Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Report on surveys and researches to excavate international joint researches related to industrial technologies; Sangyo gijutsu ni kansuru kokusai kyodo kenkyu hakkutsu no tame no chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Five themes were taken up for a project of the 'surveys and researches to excavate international joint researches related to industrial technologies'. Investigation groups were organized and dispatched for each theme toperform domestic and overseas surveys. Discussions were given on eachtheme for the possibilities of structuring international joint researches. The five themes are as follows: 'wearable information network related technologies', wherein technologies to micronize information devices have been advanced rapidly, and the technologies are entering the age from personalizing and mobilizing the information into the wearable computing; this theme is intended to develop systems to unify these technologies by means of international joint researches: 'surveys on using unutilized animal oils and fats as chemical raw materials', which are intended to make clear possibilities and problems in utilizing animal oils and fats as raw materials for the chemical industry that can substitute fossil resources: 'international joint researches on new glasses' and 'processes to manufacture semiconductors using glassy carbon' to develop glassy carbon having excellent chemical resistance substituting quartz: and 'international joint researches on the Russian project which places environment and energy in its center'. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) -research/study concerning international cooperation (Volume 1. research/study for promoting international cooperation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru chosa kenkyu (1. kokusai kyoryoku suishin no tame no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Various measures were implemented with the aim of realizing the 'longterm vision for international cooperation' in connection with hydrogen utilization international clean energy system technology (WE-NET) formulated in fiscal 1996. The English version of the 1998 annual summary report on results was distributed to approximately 170 pertinent organizations overseas. To develop understanding of the WE-NET project, presentations were given in numerous international conferences. In addition, as research cooperation in IEA (International Energy Agency), specialists were dispatched to the hydrogen implementation committee, the corresponding committee to hydrogen implementation agreement, and to each annex. In international exchange of technical information, each WE-NET task exchanged information with organizations abroad through overseas survey and conducted research on European hydrogen project, for example. With the purpose of developing understanding of WE-NET project activities, a preparatory work was done for participation in HYFORUM2000 (Germany) and World Hydrogen Energy Conference (Beijing) which will be held in 2000. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

International research cooperation in fiscal 1997. Report on the research, development, and evaluation of environmentally-friendly combustion technologies; Kokusai kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the research and development of environmentally-friendly combustion technologies that had been conducted for six years beginning in 1992, analysis and discussion were made by a special committee dedicated to the evaluation of the efforts, and the outcome is stated. In the study of zeolite-base catalysts, a highly active catalyst was developed which assumes a multilayer structure of mordenite, etc., with titanium introduced thereinto using an NO-selective reducing catalyst. As for metal complex oxide-base catalysts, various catalysts high in activity were developed, based on saponite which is a laminar, clayey compound. As for alumina-base catalysts, details were learned of the reaction mechanism and catalysis activation sites and, helped by the findings, a silver-supporting alumina catalyst was produced. In the study of direct decomposition type NOx removing catalysts, a success was achieved in causing NO to be decomposed with high selectivity in an oxygen atmosphere by use of new-type electrodes, functional layers, and solid electrolytes. In the field of catalytic combustion, a PdO-Pt/Ba-Al2O3 catalyst was developed, which is to serve for a hybrid type catalytic combustion method. 19 refs., 112 figs., 25 tabs.

Fiscal 1996 survey of potential international cooperation for a long-term scenario on CO2 reduction; 1996 nendo CO2 sakugen ni kakawaru choki shinario ni kansuru kokusai kyoryoku kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of working out a CO2 reduction scenario and a CO2 policy introduction scenario, a survey was conducted of comparisons between ten and several models which are world-known and models of the New Earth 21, potential international cooperation to be carried out in the future, etc. The survey included organizations which are developing CO2 policy evaluation models, survey reports made in the past, details of literature for the analysis and arrangement. From the result, details of the questionnaire survey and organizations to be surveyed were decided on for the questionnaire survey. Objects for the survey were 7 countries and 22 organizations, and survey items were places for information exchange, sending/receiving of researchers, exchange of input data, comparative calculation based on the common database, joint research work, economy, the carbon tax, impact, renewable energy, how to handle and think of the carbon isolation, etc. As a result of the survey, proposed were a workshop on CO2 reduction, a comparative study of simulation models, etc. 25 refs., 50 figs., 12 tabs.

Kyoto protocol and related issues; Chikyu ondanka boshi Kyoto kaigi (COP3) to sono kadai

Energy Technology Data Exchange (ETDEWEB)

Ninomiya, Y. [Global Industrial Social Progress Research Institute, Tokyo (Japan)

1997-09-30

The Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change (COP3) will be held in Kyoto in December 1997. Described herein are the current status and issues of the convention. USA and Japan, which hold important keys to set up the abatement target, have issued no proposals concretely at the current AGBM (Ad-hoc Group Berlin Mandate) 7, and the conference for the concrete targets will be decided in the next AGBM 8 to be held in October. The final target will be set by the ministerial segment of COP3, because the negotiations for the treaty are political in nature. USA proposes reduction at a uniform, realistic rate, and Japan proposes reduction at a uniform rate or setting up the emission target per capita, each being different from reduction at a much higher uniform rate proposed by EU. Within EU, however, 10% out of 15% reduction rate it proposes is agreed by the member countries, and the remaining rate of % may not be agreed. It is necessary for the advanced parties to set up realistic and legally binding solutions, including ratification by USA, which can persuade the developing countries. tab.1

6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 2. Research study on promotion of international cooperation (standardization of hydrogen energy technology); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 2. Kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes the basic study on standardization of hydrogen energy technology, and the research study on ISO/TC197 in fiscal 1996. As a part of the WE-NET project, the subtask 2 aims at preparation of standards necessary for practical use and promotion. Developmental states in every field of hydrogen energy technologies, current states of domestic/overseas related standards and laws, and needs and issues of standardization were surveyed. In particular, the needs and issues were clarified in relation to existing standards and laws from the viewpoint of specific hydrogen property. ISO/TC197 was established in 1989 for standardization of the systems and equipment for production, storage, transport, measurement and utilization of hydrogen energy. Four working groups are in action for the supply system and tank of liquid hydrogen fuel for automobiles, the container and ship for complex transport of liquid hydrogen, the specifications of hydrogen products for energy, and the hydrogen supply facility for airports. The draft international standards were proposed to the international conference in 1996. 16 refs., 21 figs., 41 tabs.

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation - 1 (Promotion of international cooperation); 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 3. Kokusai kyoryoku ni kansuru chosa kenkyu - 1 (kokusai kyoryoku suishin no tame no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

International research cooperation was promoted and technical information was internationally exchanged for the development of the International Clean Energy Network Using Hydrogen Conversion (WE-NET) Project into a truly international cooperation project. In the promotion of international research cooperation, a collection of summarized achievement reports for fiscal 1999 translated into English, based on achievement reports on the respective tasks, was disseminated to 157 related organizations overseas. Activities related to the WE-NET Project were actively presented at international conferences. For research cooperation at IEA (International Energy Agency), engineers were dispatched to its committees and annexes specializing in hydrogen related implementation agreements. In the international exchange of technical information, overseas surveys were conducted for fulfilling the purposes of the respective WE-NET tasks. Investigations were conducted into the latest fuel cell development status across the world, not to mention the automotive fuel cell now attracting earnest attention. Moreover, surveys were conducted of hydrogen energy related research institutes abroad, and a Japanese booth was installed at Hyforum 2000 (The International Hydrogen Energy Forum 2000). (NEDO)

Fiscal 1997 international cooperation project. Report on the results of the research on environmental harmony type combustion technology; 1997 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Out of the R and D on the environmental harmony type combustion technology, the results of the project carried out in fiscal 1997 were summed up. In the site survey, etc., visits were paid to France, Spain, Greek, Germany, the U.K. and the U.S. to have discussions and examine the trend of research on the NOx removal catalyst and catalyst combustion. In the actual R and D, the R and D were conducted on zeolite base NOx removal catalyst, oxide composite base NOx removal catalyst, alumina base NOx removal catalyst, direct decomposition type NOx removal catalyst, catalyst combustion, etc. In the R and D of the catalyst combustion, durability under high gas flow flux was examined of PdO-Pt/Ba-Al203 catalyst developed for low temperature use, which indicated that durability and low temperature activity were heightened. As high temperature use catalyst, high temperature durability was examined of the developed Pd0-La/Gd-ZrO2 catalyst, which showed that the durability was favorable. 322 refs., 261 figs., 55 tabs.

Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

Feasible study of international cooperation on the long-term scenario for reducing CO2. DNE-21 simulation database; CO2 sakugen ni kakawaru choki scenario ni kansuru kokusai kyoryoku kanosei chosa. DNE21 simulation database

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes calculation codes of DNE-21 which can simulate the optimization model for reducing CO2. The DNE-21 was modified from the former NE-21. The term was set between 2000 and 2100. Optimization can be conducted across the different time. Non-conventional petroleum was removed from the primary energy. Capacity of nuclear power generation facilities was taken in the model for the optimization. Decision making analysis can be done by considering the uncertainty. The DNE-21 has eleven input files including the model operation, technical property related data, cost related data, data of tax, subsidy and customs, and scenario data of future energy demand and supply, GNP, population and nuclear power. The DNE-21 has fifteen output files including the optimization calculation results for the world, Oceania, the Middle East, North Africa, Central America, South America, former USSR, and OECD countries. 2 figs.

International Ocean Symposium (IOS) 1996; Kokusai kaiyo symposium 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-18

This is a proceedings of the International Ocean Symposium 1996. On the first day of the symposium, the following were given with a theme `The Ocean, Can She Save Us`: Underwater research and future of mankind as a commemorative speech; The ocean, can she save us -- trying to discover the true figure of the ocean as a keynote speech. Panel discussion was held on The global environment and the infinite potential of the ocean. On the second day, an approach was made mostly from a cultural aspect with a theme `The Ocean and the Japanese.` The following were given: Human links between east and west as a commemorative speech; The ocean and Japanese culture as a keynote speech; Civilization spanning across oceans as a panel discussion. The Japanese have been developing their individual technologies in shipbuilding, shipping, and ocean development, have been raised by Mother Ocean, and have lived together. Ocean has been supplying humans food, water, oxygen, marine routes, and even dream and hope. The environmental pollution is the result of the human greediness. It is fear and friendship between humans and ocean that can save humans and ocean.

Fiscal 1995 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1995 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research and development were conducted jointly with Europe of an environmental harmony type high efficient catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. In the research and development of NOx removal catalyst such as zeolite base, reformation of mostly mordenite was done by ion exchange, ion implantation, skeleton element substitution, etc. A possibility was found out of applying the membrane formation method except ion implantation as reforming means. In the R and D of the complex oxide base NOx removal catalyst, it was found that the catalyst carrying copper and silver on silica and layer clay compound under optimum conditions shows peculiarly high activity, and there is little decrease in the activity, but rather increase in it even under vapor existence. An evaluation was made of NO resolution of direct resolution element carrying noble metal electrolyte on solid electrolyte, finding out that the highest NO selectivity is shown with Pd as electrolyte and at a baking temperature of about 1300degC. Development of high- and low-temperature catalysts was also made. 417 refs., 286 figs., 63 tabs.

Fiscal 1996 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1996 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research was conducted jointly with Europe of a catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. Reformation of mordenite and {beta}-zeolite was done by ion exchange, ion implantation, and membrane formation. A catalyst was searched for to obtain reducing agents, C5-C8 components, by decomposing light oil. Saponite, clay compound, showed by copper and silver ion exchanges approximately 50% of activity under 20,000h{sup -1}, C3H6 reducing agent, and without steam. The effect of the temperature of sintering on NOx selective reductionality of silver-carrying alumina catalyst was studied, and in sintering at 800degC, activity increased. When using conductive oxides like ruthenium oxide for electrolyte, NO decomposition selectivity increased. As to the functional layer carried above the Pd electrolyte, iron oxide and magnesium oxide increased NO decomposition selectivity. PdO and rare earth oxides forming compounds controlled variation of activity by dissociation/reoxidation of PdO. As to PdO/Gd203, the initial methane combustion activity was favorable, but there was seen deterioration with age. 271 refs., 281 figs., 58 tabs.

FY1998 report on a survey related to joint utilization of welfare device development data using an international network; 1998 nendo kokusai network ni yoru fukushi kiki kaihatsu data no kyodo riyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A survey was made in relation with joint utilization of welfare device development data using an international network. Developing welfare devices requires data from ergonomic and medical systems, while the cope of the objects is wide, and the kinds are various. For proliferation of welfare devices, system compatibility evaluation including that on using environment is important, including living environments that are different by countries. The present survey has identified how data for aged, handicapped and help-needing persons are accumulated and utilized in research organizations in America and Europe for both of the ergonomic and medical areas. The survey also investigated major academic societies in overseas countries, and collected database and academic network information that support the advanced research and development. At the same time, investigations were also made on organizations and corporations who are moving forward the efficient data utilization. Welfare device and service information providing systems in Japan were investigated to compare them with the trends in other countries. Conceptions and methods were compiled to utilize data internationally and jointly. Database models for device development were considered, and a proposal was made on structuring a research and development supporting database, and the operation method thereof. (NEDO)

Fiscal 1998 research report on International Clean Energy Network using Hydrogen Conversion (WE-NET). Subtask 2. Research on promotion of international cooperation (research on standardization of hydrogen energy technologies); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) sub task. 2. Kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the fiscal 1998 research result on the basic research on standardization of hydrogen energy technologies, and ISO/TC197. As for the standardization, in relation to the hydrogen station in the WE-NET second phase research, the laws related to handling of gaseous hydrogen, and the basic issues on facility and safe handling were studied. As for ISO/TC197, the following draft standards were examined: Fuel supply system interface for liquid hydrogen vehicles, fuel tank for liquid hydrogen vehicles, container for liquid hydrogen transport, specification of hydrogen fuel, hydrogen fuel supply facility for air ports, gaseous hydrogen and hydrogen mixture fuel system for vehicles, gaseous hydrogen fuel connector for vehicles, gaseous hydrogen fuel tank for vehicles, and basic items for hydrogen system safety. Final examination of the fuel supply system interface for liquid hydrogen vehicles, and the specification of hydrogen fuel was finished, and these are scheduled to be registered for ISO. (NEDO)

FY 2000 Report on the survey results. Survey on international cooperation for development of a system for supporting low-invasion surgical operations; 2000 nendo teishinshu shujutsu shien system kaihatsu ni kakawaru kokusai kyoryoku ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The international Medical Treatment Symposium and Exhibition were held from July 20 to the end of August, 2000 in Hannover in Germany, in which the Japan's system for supporting low-invasion surgical operations was presented and information was exchanged for the system. A total of 50 to 100 neurosurgeons visited the exhibition, held as part of the symposium, every day from July 21 to 24. The system for supporting low-invasion surgical operations is rated as the most advanced one in the world. It attracted much attention, because a number of attendees applied for operating manipulator. The research trends seen in the symposium point to early diagnosis of diseases, finer surgical operations, low-invasion type operations, use of high-function diagnosis devices for improving operations, real-time imaging, and application of DNA diagnosis to pathological diagnosis, among others. Japan is leading the world in the technological areas of micromachines, robotics, high-vision and diagnosis. The bold researches, e.g., those on artificial visual and hearing systems to be embedded in the head, are pursued more extensively in the overseas countries. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Energy conservation No.2). Achievement report on international joint study on popularization promotion of geothermal heat pump-assisted environmentally compatible heating system for Changchun City, China; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (Shoe No.2). Chinetsu heat pump ni yoru Chugoku Changchun shi kankyo tekigogata danbo system no fukyu sokushin ni kansuru kokusai kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A geothermal heat pump-assisted heating system is introduced into Changchun City and a survey is conducted to determine if the system may be popularized in this extremely cold region located in the northeastern part of China. In concrete terms, the hot water that circulates through the office building of Changchun Ground Heat Development Co., Ltd., is switched to hot water prepared by a geothermal heat pump. The test continued from December 2000 to March 2001. It is then concluded that heating by geothermal heat pumps will be fully serviceable to Changchun City. Implemented are (1) the shift from the coal fired boiler system to a geothermal heat pump system comprising 16 subterranean heat exchangers for the heating of the office building which is approximately 1000 m{sup 2} large, (2) long-term monitoring of the operating conditions, (3) measurement of subterranean heat exchanger thermal conductivity and subterranean temperature, and (4) the study of pipe shapes for improved thermal efficiency, grouting materials, and the like. (NEDO)

FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries and programs of international conferences including IPCC. Report on CDM workshop; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / IPCC nado kokusai kaigi jigyo (CDM workshop hokokusho) 1998 nendo jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It is decided in the COP4 that the concrete schemes for the (Kyoto Mechanism) should be boiled down towards the end of 2000. Of the many outstanding issues concerned, those related to the clean development mechanism (CDM) involve a number of problems awaiting solution. In particular, setting the baselines for amounts of the greenhouse effect gas emissions in projects not existing, which are essential for identifying reduced amounts of emissions (or credits), poses serious difficulty because of wide arbitrariness involved in the methodology. Therefore, (standardization) of the procedures is demanded for the accurate identification. In actuality, however, no methodology has been established as to what methods will be possibly applicable to widely diversified types of projects. This workshop, therefore, has focused the discussions on the (baseline problems), expecting to serve as a trigger for the future directions by presenting international researches and promoting the discussions thereon to deepen recognition of these problems, where the AIJ experiences have served as one of the bases. (NEDO)

Fiscal 1997 survey report. Subtask 2 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study for the promotion of international cooperation; survey/study on the standardization for hydrogen energy technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In relation to the basic study of the standardization for hydrogen energy technology and ISO/TC197, the results of the fiscal 1997 survey were summarized. From fiscal 1994 through 1996, in the wide-range field related to hydrogen energy technology, the survey of the present situation of the related standards/laws was made and the needs/subjects of standardization to be studied in the future were extracted. At the present stage, however, it is still early to enter into the stage of discussing the standardization. Therefore, in this fiscal year, only in the field of the storage/transportation/handling of liquid hydrogen, standards/laws abroad and in Japan were comparatively investigated for the basic study toward the standardization. Further, concerning ISO/TC197, studies were proceeded with of the liquid hydrogen land vehicle fueling system interface/fuel tanks/transportation containers/hydrogen fuel product specifications/airport hydrogen fueling facilities. Some are at the stage of drafting the international standard. Three drafts for the new standard were added such as gaseous hydrogen/hydrogen blend vehicular fuel systems, gaseous hydrogen fuel tanks, and basic requirements for safety of hydrogen systems. The standardization is indispensable to introducing the developed technology to the commercialization. 9 refs., 5 figs., 13 tabs.

Proceedings of the papers of the 33rd Coal Science Conference (1996); Dai 33 kai sekitan kagaku kaigi happyo ronbunshu (1996)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-28

This is a proceedings of the papers made public in the 33rd (fiscal 1996) Coal Science Conference held by the Japan Institute of Energy. The number of the papers included is 82. The processes such as coal liquefaction, coal gasification and pyrolysis are largely influenced by reaction of the carbon compound in coal. However, coal, which is different in reaction characteristics depending on its producing area, is a comprehensive compound. Therefore, the trial has been made for clarifying the molecular structure and skeleton. In the sense, the following papers are taken notice of: Suzuki and others` Estimation for origin of coals by biomaker analysis; Sugimoto and others` Change of unit skeletons during the artificial coalification; Hirado and others` Study on the correlation between chemical and mineral composition of coal ashes; Okawa and others` Coal structure construction system with construction knowledge and partial energy evaluation; Kanbayashi and others` Analysis of the relationship between coal properties and liquefaction characteristics by using the coal database.

Fiscal 1991 report. International Fuel Cell Conference; Nenryo denchi kokusai symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Lectures, presentations, and questions given at the event involved items 1) Plenary session, 2) Technology development strategies, 3) Phosphoric acid fuel cell (PAFC), 4) Molten carbonate fuel cell (MCFC), 5) Solid oxide fuel cell (SOFC), 6) Other fuel cells, and item 7) Closing session. Under item 1), current states and prospects of technological development were reported by Agency of Industrial Science and Technology of Japan and by industrial technology developing organizations of the U.S. and Europe. Under item 2), a report was given by the U.S. about a fuel cell-driven automobile developing program. Under item 3), a report was given on the exchange of information about plant operation, maintenance, and inspection with importance attached to accuracy. Under item 4), reports were given about a 70kW stack operating program of the U.S. and a 1MW stack pilot plant program of Japan. Under item 5), some NEDO (New Energy and Industrial Technology Development Organization) projects and a 25kW stack operating test of Westinghouse Electric Corporation were reported. What were learned through participation in this conference are mentioned below. Japan is in the forefront as far as the development of PAFC and MCFC technologies are concerned. The U.S. is ahead of Japan in the development of SOFC while also in Japan efforts to develop element technologies for SOFC are in progress steadily. The U.S. and European countries lead Japan in the development of the polymer electrolyte fuel cell (PEFC). (NEDO)

International research on energy conservation techniques; Energy shiyo gorika shuho kokusai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to utilize energy reasonably over the whole life cycle of products, the life cycle assessment (LCA) was researched including assessment of the quantity of environmental load. LCA is composed of the inventory analysis which analyzes objectively the amount of input and output of all substances and energy due to their gathering, mining, transport, production, use, recycling and scrapping, and the impact analysis to environment based on the inventory analysis. The inventory analysis of refrigerators was conducted. The unit amount of CO2 emission generated by production of materials was estimated on the basis of previous papers. In particular, CO2 emission due to overseas production of imported raw metals reached nearly 80% in Al and 70% in copper. Recycling of materials and heat recovery by combustion of waste were also considered. Environmental effect was next assessed using the inventory data in three stages of classification, characterization and valuation. Although the weight factor of environmental effect is necessary for every emission, European and American data are now used. 59 refs., 68 figs., 81 tabs.

Public subscription project for international joint research proposals in fiscal 2000 - public subscription of international proposal (substitution No.3). Report on achievements in research related to industrial utilization and social systematization of gas hydrate technologies; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (daitai No.3). Gas hydrate gijutsu no sangyo riyo shakai system ka ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Activities have been advanced to establish necessary basic technologies by making clear the possibilities and problems in applying gas hydrate technologies to industrial fields. Activities have been taken in the following three fields: 1) industrial utilization and social systematization of gas hydrate technologies, 2) conceptual design of gas hydrate utilization technologies, and 3) researches on basic technologies to utilize the gas hydrate technologies in industries. In Item 1), discussions were given on significance of social systematization of the gas hydrate technologies, conditions for social systematization of the gas hydrate technologies, the current status of natural gas development and industrial utilization of the gas hydrate technologies. In Item 2), discussions were given on utilization of gas containability (application to natural gas transportation and storage processes), utilization of cold heat storage performance (utilization to suction air cooling of gas turbine generators), and utilization of gas selectivity (application to gas separation processes and acidic gas (CO2, SOx) separation). (NEDO)

Public subscription project for international joint research proposals in fiscal 2000 - public subscription of international proposal (substitution No.3). Report on achievements in research related to industrial utilization and social systematization of gas hydrate technologies - Separate volume; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (daitai No.3). Gas hydrate gijutsu no sangyo riyo shakai system ka ni kansuru kenkyu kaihatsu seika hokokusho (bessatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Investigations were performed on important properties when utilization of gas hydrates to industries is discussed, such as production and decomposition speeds and storage stability. Activities have been taken in the following two fields: 1) experimental studies on production and decomposition of gas hydrates, and 2) summarized view on research related to gas hydrate self-retention effect. In Item 1), a production device of stirring system using rotating blades with gas circulation holes (self-suction type) was fabricated to have discussed the production and decomposition speeds. It was made clear that the production speed is governed by the over-cooling degree under the appropriate gas circulation and appropriate stirring conditions, and that the decomposition speed becomes abnormally high unless the self-retention status is maintained. In Item 2), following the introduction, seven researches were introduced, including the first observation of abnormal reaction of gas hydrate under the decreased pressure condition, the research by Yu. P. Handa related to gas hydrate decomposition below zero degree C, and the research by E. Mayer and A. Hall Brucker related to unexpectedly stable nitrogen, oxygen, carbon monoxide and argon clathrate gas hydrate formed from amorphous solid water. (NEDO)

Study on cobalt oxide; Sanka kobaruto ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

This is No.91 report of National Institute for Research in Inorganic Materials, concerning cobalt oxide. For the growth of single crystal by the Czochralski method, shape of interface and contamination of impurities are affected by the convection of molten liquid in the atmosphere. Various oxides besides CoO were investigated. Solid solutions of Cr2O3 and Al2O3 into CoO were also studied. Non-linear optic and dielectric properties of single crystals, such as Ba2NaNb5O15 and LiNbO3, were examined. It was considered that the positive electron having positive electric charge can be used for the study on the negative electric charge defect in materials. However, the positive electron itself is rare, which results in the too low efficiency of measurement. Efficiency improvement of 50 times was achieved by introducing a high performance 2D position detector, which was still low efficiency of one-hundredth compared with photoelectron spectroscopy. It was found that the aggregation structure of positive ion defects in CoO is a misunderstanding of phenomenon caused by the electronic state in bulk crystals. As a result of the study on the optical properties of f-electron transition metals, transparent ceramics with addition of various rare earth ions were described. 162 refs., 106 figs., 14 tabs.

Studies on silicon nitrides; Chikka keiso ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Sinters of silicon nitrides have excellent properties as a structural material, but their technological repercussion effect is not as much as has been expected. The cause is in insufficient understanding on the mutual relationship between microstructures and mechanical properties. Therefore, methods of controlling structures were first discussed in the studies on synthesis of high-tenacity ceramics. In order to achieve high reliability in material strength, discussions were given on means to have a structure developed with high reproducibility. Development was performed on {beta} powder which shows no abnormal grain growth and is stable at elevated temperatures. Then, quantitative evaluation was made on factors to manifest a self-compounding structure with columnar particles grown in ultrafine particles. The relationship between its chemical composition, microstructure and mechanical properties was also discussed. Particle shapes of silicon carbides and their fracture tenacity values were considered theoretically by using a drawing model. To evaluate the microstructure, it is important to determine the grain boundary composition, whereas an electric field radiation type high-performance electron microscope was developed. In discussing the fracture mechanism, a model was structured for behavior of covalent binding crystals against external stress. 164 refs., 95 figs., 10 tabs.

Study on apatite compounds; Apataitokei kagobutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

To clarify the material properties of apatite compounds, the synthesis method, and the evaluation of physical properties of material and elementary technology were investigated. For the study on synthesis and crystal growth, a method of precipitating calcium phosphate on the surface of metal was investigated by means of relatively mild electrolytic method using liquid phase system. A new molding method of Ca defective apatite was established. Composite similar to vital bone was prepared by means of a new low-temperature sintering. For the study on chemical properties, from the model experiments, it was found that the self-organizing phenomenon, which is observed in the composite of apatite and collagen, happened between the organic single molecular film and crystal of apatite. For the study on evaluation of physical properties and elementary technology, the surface and interface of ceramics such as apatite were investigated by means of spectroscopy, the electronic state was analyzed by the quantum chemical calculation, and the crystalline structure was analyzed using X-ray equipment. 270 refs., 102 figs., 10 tabs.

Study on electroseismic prospecting; Electroseismic tansaho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onaru, I [Kyushu University, Fukuoka (Japan); Irie, S [Mitsubishi Materials Corp., Tokyo (Japan); Tanaka, T; Mizunaga, H; Ushijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-22

This paper illustrates the results of field tests conducted as a basic investigation of electroseismic phenomenon at the site of Kyushu University. The electroseismic phenomenon is a physical phenomenon in which electromagnetic response is derived by the incident elastic wave in the underground. According to Karl E. Butler, et al., mutual motion occurs between rock matrix and pore water by the propagation of P-wave in porous media. Spatial change in the water content per unit volume occurs, which is similar to the density change with the propagation of P-wave in elastic solid. Since the pore water with mobility can bring charges generated in the electrical double layer, the change in the water content agrees with the density change. Accordingly, domains of positive and negative overcharges are generated at the top of P-wave, which can be a current source. An electric field is generated between the domains. As a result of the field tests, it was confirmed that electromagnetic phenomena can be derived by the elastic waves. 2 refs., 8 figs.

Study of white noise; Hakushoku zatsuon ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kano, R; Tada, R [Teikoku Oil Co. Ltd., Tokyo (Japan)

1996-05-01

A study was made on conditions available for white noise belonging to a finite power function with the use of a power spectrum conception. It was defined that a real variable function with a finite waveform energy was a finite energy function while that with a finite waveform power was a finite power function. A noncorrelative white noise was defined as a real variable function in which an autocorrelation function took a specific value at a certain point; however, the autocorrelation function was different between the finite energy function and the finite power function. In other words, the definition of white noise was such that `an energy spectrum was a fixed value` in the finite energy function, and that `a power spectrum was a fixed value` in the finite power function. It was pointed out, by Matsuyama (1994) with the use of the energy spectrum conception, that the white noise belonging to the finite energy function took only the form of `an arbitrary impulse function that all turned to zero except a certain point`. The same conclusion was obtained with respect to the white noise belonging to the finite power function. 1 ref., 1 tab.

Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 7. Survey/study on hydrogen utilization technology; 1998 nendo suiso riyo kokusai clean energy system (WE-NET). 7. Suiso riyo gijutsu ni kansuru chosa kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper described the results of survey/study of the FY 1998 WE-NET project. In Subtask 7, survey/study have been made on the main hydrogen utilization technologies except the hydrogen combustion gas turbine since FY 1993. Based on the survey results having been obtained, study was made on conditions for introducing promising technology, future prospects, etc. in FY 1998. As to the power generation, the basic combustion test and test on hydrogen injection equipment as element test, and test on ignition equipment were carried out using rapid compression/expansion equipment. A scenario for introducing hydrogen vehicle was made, and at the same time environmental LCA was conducted by which environmental influences can be assessed. The survey of the market of pure hydrogen polymer electrolyte fuel cells were made in terms of the electric utility use, industrial use, residential/commercial use, and movement/vehicle use. Study was conducted on the combined process of oxygen production equipment and He Brayton cycle in the subzero fractionation/low-temperature VSA method. Various methods including performance, price, etc. were surveyed/studied, making it a precondition that hydrogen supply stations are installed in stand-alone distribution near places of consumption. (NEDO)

Study of biogas storage; Biogas no chozo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Kimura, T; Umeda, H [Meiji University, Tokyo (Japan)

1997-11-25

Study was made on the storage method of a methane component in biogas mainly composed of CO2 and methane gases. Methane clathrate as molecular complex is one kind of clathrate compounds. Eight methane gas molecules are absorbed into 46 water molecules, or methane gas of 216 l is absorbed into water of 1 l, resulting in considerable compact methane storage. Although methane clathrate is usually stable only under a condition of low temperature and high pressure, its formation equilibrium shifts toward a low pressure/high temperature side by adding additives such as amine, ether and ketone. Acetone can shift formation pressure from 30 to 10atm at 1degC, and formation temperature from 1 to 10degC at 30atm. Although methane liquefaction is also an efficient storage method, it requires liquefaction temperature and pressure of -83degC and 45.6atm, respectively. The distance between methane molecules in clathrate lattice can be more shortened than that in high- pressure charged gas, suggesting higher storage efficiency. The study result showed that the handling of methane clathrate is possible around room temperature and pressure. 7 refs., 5 figs.

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

Fiscal 1999 technical achievement report. Research and development project on the quickly effective international standards creation (Standardization of safety of light emitting diode or the like); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Hakko diode nado no anzensei ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Since radiation of a laser diode (LD) is quite different from that of a light emitting diode (LED), evaluating their safety under one and the same standard (criterion) is questionable. The International Electrotechnical Commission (IEC), however, treats them in the same way. For the remedy of such contradiction and for the clarification of difference between the two devices in terms of radiation characteristics, they were quantitatively measured for spatial coherence and further measured for coherence dependency of their beam diameters. Well-supported threshold levels were prepared and biological tests were conducted for proposing a revision of the LED safety standard (IEC). As for the safety of equipment with built-in infrared devices, a measurement method was prepared as IEC61913 and devices are already at the CVD (chemical vapor deposition) stage. The result will be placed before the IEC/TC76 committee for deliberation of IEC60825-1 revision. Furthermore, to establish alignment between IEC and ISO (International Standardization Organization) in terms of laser-aided measurement which is the foundation for such committee deliberation, an ISO/IEC international joint group was created, and a technical recommendation was compiled and presented to the two standardizing organizations. (NEDO)

Fiscal 1997 survey report. Subtask 9 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study on the innovative and leading technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 9 kakushinteki, sendoteki gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of giving useful suggestions/proposals to the course of WE-NET and contributing to the R and D, conducted were survey/collection/evaluation of new technologies. The paper described the fiscal 1997 results. The number of the proposals of new technology accumulated during fiscal 1993 to 1997 is 28. The proposals of new technology made in fiscal 1997 are hydrogen production effectively using solar energy by wavelength zone, hydrogen storage using fullerene, and the methanol power generation turbine system. Four technologies proposed in fiscal 1996 and 1997 were evaluated. The evaluation method requires two steps of the marking using the analytic hierarchy process (AHP) and the adjustment by the committee. The highly evaluated proposals out of those having been made were analysis/evaluation of hydrogen-oxygen internal-combustion Stirling engine, hydrogen production effectively using solar energy by wavelength zone, hydrogen production by solid oxide electrolysis, magnetic refrigeration method for hydrogen liquefaction, hydrogen production technology using photocatalyst, etc. The paper also stated the result of studying concepts of innovative/leading technologies in fiscal 1996. 4 figs., 29 tabs.

Trend of the bioceramics (for the international standardization); Baioseramikkusu no doko. Kokusai hyojunka nimukete

Energy Technology Data Exchange (ETDEWEB)

Kurita, Manabu

1999-11-01

The Ministry of International Trade and Industry Agency of Industrial Science and Technology would carry out development research of the standardization of test evaluation method of fine ceramics for the organism as research and development business of the international standardization promotion plan since this fiscal year. The fine ceramics becomes not possible material of lacking as alternative material of the organism. The public standard which appropriately evaluates the quality material in the other has not been established. JIS in the home of the result which there is Japan Fine Ceramics Association standard (test methods such as porosity and specific gravity, grain size, pore distribution, specific surface, Vickers hardness, crystal structure, bending strength, compressive strength, elastic modulus, fracture toughness, effluent of the bioceramics) JIS has not been instituted. It is present state that it becomes the Europe and America initiative artificial joint artificial bone expert committee TC-150 surgical internal burying agent ISO (ISO) and takes the one step delay. And, security of the reliability is necessary in order to fulfil the popularization in the market. The standardization must be hurried up. Research and development of test evaluation method of fine ceramics for the organism was carried out in order to attempt market expansion taking the reliability of fine ceramics material performance for the organism in our country as a sure thing, and standardizing into JIS and international standardization would be systematically advanced. Efforts would be made in fiscal 99 for research and development of evaluation method on abrasion resistance of artificial bone member subject, mechanical property such as strength degradation and biocompatibility. The technical committee of the industry-government-university from the specialist which consists in this inside is founded, and the deliberation for plan execution of this study development is got and will be effectively propelled. By lumping together, the development research will be entrusted in the foundation fine ceramics center. (translated by NEDO)

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

Report on Seminar on Clean Coal Technology '93; Clean coal technology kokusai seminar hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-11-01

The program of the above clean coal technology (CCT) event is composed of 1) Coal energy be friendly toward the earth, 2) Research on CCT in America (study of coal structure under electron microscope), and 3) Research on CCT in Australia (high intensity combustion of ultrafine coal particles in a clean way). Remarks under item 1) are mentioned below. As for SO{sub 2} emissions base unit, Japan's is 1 at its coal-fired thermal power station while that of America is 7.8. As for the level of SO{sub 2}/NOx reduction attributable to coal utilization technologies, it rises in the order of flue gas desulfurizer-aided pulverized coal combustion, normal pressure fluidized bed combustion, pressurized fluidized bed combustion, integrated coal gasification combined cycle power generation, and integrated coal gasification combined cycle power generation/fuel cell. As for the level of CO2 reduction attributable to power generation efficiency improvement, provided that Japan's average power generation efficiency is 39% and if China's efficiency which is now 28% is improved to be similar to that of Japan, there will be a 40% reduction in CO2 emissions. Under item 2) which involves America's CCT program, reference is made to efforts at eliminating unnecessary part from the catalytic process and at reducing surplus air, to the export of CCT technology, and so forth. Under item 3), it is stated that coal cleaning may govern reaction efficiency in a process of burning coal particles for gasification. (NEDO)

Fiscal 1998 international research cooperation project. Feasibility study report on excavation of international joint research seeds; 1998 nendo kokusai kyoryoku jigyo seika hokokusho. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study (FS) was made on excavation of international joint research seeds for developed countries. As FS themes, 6 themes were selected among applied 11 ones. China was interested in the joint research on improvement of a cetane number by ring-opening of LCO from fluid catalytic crackers through hydrogenation for Arabian crude oil, although China has an experience for domestic one. Since France and the USA are in the early developmental stage of practical atmospheric temperature and pressure conversion technology of lower hydrocarbon after the basic research stage, study was made on the possibility of a joint research. The other themes are as follows: Oil resource and energy conservation technology by recycling general plastics and industrial synthetic resins, advanced solid catalyst regulating technology by physicochemical technique and its application to next-generation oil refining processes, structure analysis of asphaltene and reaction mechanism analysis of heavy oil by computer simulation, and production technology of ultra-precisely controlled catalytic materials. (NEDO)

Preprint of the 40th material study joint lecture of Science Council of Japan; Dai 40 kai Nippon gakujutsu kaigi zairyo kenkyu rengo koenkai maezurishu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-19

The paper stated mostly topics from special lectures. Composite materials have a lot of potentialities, and there are larger expectations in flexible and high-strength soft composites rather than the conventional high rigidity ones. As to micro-machines, the problems are on mechanical property of the element, environment/friction/fracture/life, etc. and the evaluation method of the characteristics was studied. Concerning the research and development of the intellectual structure system, the introductive study has entered the second year. Ultimately, structures have functions similar to those of the living organism had, and conduct self-diagnosis, self-repair and autonomous-response. Railroad structures receive regular inspections according to the rule, and a half of the objects for the inspection are cracks, unbonding and weathering of concrete. With the Hanshin Awaji great earthquake especially, the anti-earthquake reinforcement has been expedited. In various kinds of materials, the finer the crystal particle becomes, the greater the high temperature deforming ability becomes. When the particle size is below the critical particle size, it shows superplasticity. The study is advancing. As to high density secondary batteries, introduced especially were Ni-hydrogen batteries and Li batteries.

Report on Symposium on Pacific Energy Cooperation 2001. Energy Security in Asian Region; Taiheiyo energy kyoryoku kaigi 2001 hokokusho. Asia chiiki no energy anzen hosho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-20

The Symposium on Pacific Energy Cooperation (SPEC), which started in 1986 to discuss energy problems and international cooperation on energy in the Pacific region, met for 2001 in Tokyo on February 20 and 21, 2001, to discuss Energy Security in Asian Region. The conference comprised two keynote addresses, four sessions, and a panel discussion. Twenty-four countries and an international organization were represented by a total of 785 participants who actively exchanged views and opinions. With Director Tsutomu Toichi, The Institute of Energy Economics, Japan, acting as chairman, two keynote addresses were delivered. Minister of Oil Bijan Namdar Zanganeh of Iran reported on The Role of I. R. Iran in Meeting the Growing Oil and Gas Demand in the Asia-Pacific Region and Potential Cooperation with the Region's Consumers. Managing Director Phil Watts of the Royal Dutch/Shell Group reported on Security in Trust - Meeting Asian Energy Needs in the 21st Century. (NEDO)

Proper knowledge about the growing fat; Himan ni kansuru tadashii chishiki

Energy Technology Data Exchange (ETDEWEB)

Sakamot, Yoichi

1999-07-01

Body fat is substituted for the energy adopted redundantly in the inside of the body, and the deep diabetes which relates to the increase in the fat person and this, high blood pressure, high fat blood diseases, ventilation and so-called life habit sicknesses such as an arteriosclerosis disease have been increasing. It thinks with growing fat when it wants it understood why it grows fat as to something as to that fearfulness about growing fat properly. The health making based on the individual and the weight control can't be missed to get the rich old age, which it lives through the middle age. (NEDO)

Studies on ternary silver sulfides; Fukugo gin ryukabutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Some sulfides containing silver show high ion mobility based on movability of silver, whose application is expected. Studies have been carried out centrally on synthesis of new compounds of ternary silver sulfides by elucidating the relationship among their compositions, structures and properties by means of crystal chemical studies mainly on their phase relationship. A few new compounds have been synthesized, such as the ones having the argyrodite family compound structure including transition metals. The synthesizing process takes a kind of turbulent liquid state structure at elevated temperatures because of movability of silver, but silver is fixed at low temperatures in different sites between skeleton structures made by other atoms. These studies on phase transfer, structures, and silver movability have been based on X-ray diffraction, infrared and Raman spectroscopic measurements, NMR, measurements of electric and thermal characteristics. For the studies related to compositions and structures of ternary metal sulfides which take compound crystalline structure, a structure analyzing method based on multi-dimensional hyperspatial groups was used. This paper reports the summary of the studies in seven chapters, and dwells on the remaining problems and future prospects. 158 refs., 114 figs., 65 tabs.

Studies of coal slurries property; Slurry no seijo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Kawabata, M.; Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Sakaki, T.; Shibata, M.; Hirosue, H. [Kyushu National Industrial Research Institute, Saga (Japan)

1996-10-28

It was previously found that the increase of slurry temperature provides a significant effect of slurry viscosity reduction for the coal slurry with high concentration of 50 wt%. To investigate the detailed influence of slurry temperature for the coal slurry with concentration of 50 wt%, influence of temperature on the successive change of apparent viscosity was observed at the constant shear rate. When the concentration of coal was increased from 45 wt% to 50 wt%, viscosity of the slurry was rapidly increased. When heated above 70{degree}C, the apparent viscosity decreased during heating to the given temperature, but it increased successively after reaching to the given temperature. The apparent viscosity showed higher value than that of the initial viscosity. The coal slurry with concentration of 50 wt% showed the fluidity of Newtonian fluid at the lower shear rate region, but showed the fluidity of pseudo-plastic fluid at the higher shear rate region. The slurry having high apparent viscosity by the successive change showed higher apparent viscosity with increasing the higher even by changing the shear rate. 1 ref., 4 figs.

Study of odor inside cars; Kuruma no nioi ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, S.; Ito, H.; Sakakibara, K.; Kaitani, K.; Hamada, C. [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Matsuo, M. [Toyota Motor Corp., Aichi (Japan)

1998-05-01

This paper describes odor in automotive cabin. Odor of new cars is rapidly disappeared during the use. This is greatly due to the adaptation of olfaction. The generation of odor is also decreased. It was found that aliphatic and aromatic hydrocarbons were rapidly disappeared. Decrements of oxygen containing and sulfur compounds were low. For amines, high boiling amines increased after three months. The odor component from crews was derived from the exhalation. Trimethylamine, methyl sulfide as well as iso-prene were detected. They could be derived from tobacco smoke, perfume and hair conditioner. Exhaust gas of diesel vehicle going ahead is one of unpleasant odors from the running atmosphere. A correlation coefficient 0.77 was obtained between the stimulation and aldehyde/ketone. A correlation equation was deduced using stimulation, discomfort degree and odor characteristics as object variables and using logarithms of trace analysis values as explanation variables. There are still a lot of unknown issues concerning combined odors. 9 refs., 9 figs., 1 tab.

FY 1998 Report on development of technologies for commercialization of photovoltaic power systems. International co-operative project (Information collected for IEA Solar Heating and Cooling Programme); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo. IEA taiyo reidanbo kyuto program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The IEA/ Solar Heating and Cooling Programme (SHCP) committee members were dispatched to the IEA/SHCP Executive Committee and Expert Meetings, to collect information, present the reports and hold the discussions, among others. Described herein are the results. The third Expert Meeting of the IEA/SHCP Task 23 prepared the document covering the examples of solar energy use in large buildings and distributed them in Subtask A, and proposed and discussed the comprehensive performance evaluation methods and simulation-based design tools in Subtask C. The second workshop of the IEA/SHCP Task 25 discussed evaluation of the current technologies for solar assisted air conditioning, design of the solar assisted cooling systems, economic evaluation and market researches, investigations of cooling system hardware, and development of simulation programs and design tools. The examples of solar cooling are mostly found in Japan, and European countries are conducting experiments and field tests, because of lack of commercial grade freezers. (NEDO)

International joint research of medical and walfare appliances; Iryo fukushi kiki kokusai kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

To further elevate the medical level and to actively enhance Japan`s contribution to the world in its effort to properly meet the task of advancing longevity of men common to all the advanced countries, investigations were made to study how international joint research should be conducted in the field of medical and welfare appliances. Candidate projects in international joint research and investigations up to fiscal 1993 were arranged, and explanation was made about the strategic and long-term research and development projects (started in fiscal 1995) about medical and welfare appliances undertaken by the Ministry of Trade and Industry of Japan. The two are quite similar to each other, the Ministry of Trade and Industry program comprising six projects that are micropores collection of blood/microdose analysis, high precision three dimensional image assisted diagnosis, less invasive surgery, artificial organs, care assisting intelligent equipment, and welfare equipment for care at home, centering about which international joint research should be propelled. Visits were made to the scenes of research and development of advanced medical and welfare appliances in the U.S. and Canada and their actual state was studied in search for possible joint researches. Further, research and development institutions in Europe were visited and information was exchanged. 25 figs., 15 tabs.

Report on the project on the researcher dispatch type international joint research survey. International joint research for creation of new industries; Kenkyusha hakengata kokusai kyodo kenkyu chosa jigyo. Shinki sangyo soshutsu kokusai kyodo kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of digging up themes of the joint research which develop the R and D in the industrial field in Japan to a new stage, researchers were dispatched to the world representing research institutes to make the research study. As to the survey of the trend of bio-informatics research, visits for survey were paid by 8 researchers to 19 research institutes in the U.S., Australia, France and Germany, and survey was made of the state of new researches such as the genetic network analysis by DNA chip data. Relating to the survey of the trend of the plan for ape genomic DNA sequence, visits for survey were paid by 6 researchers to 12 research institutes in Japan, Germany, France and the U.K. Concerning the research survey with aim of developing the selective reversible expression technology of target genes, researchers were dispatched to St. Jude Children's Research Hospital in the U.S. to conduct the following: construction of basic expression vectors, functional evaluation using cultured cells, making of the transgenic mice to which medicine dependent and cell peculiar expression control genes were introduced, analytical study of the situation of expression control, etc. (NEDO)

Recent topics on aerodynamic noise; Kuriki soon ni kansuru saikin no wadai

Energy Technology Data Exchange (ETDEWEB)

Nishimura, M [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

1995-04-20

For measures to deal with aerodynamic noise, recent subjects were put in order and some examples of the studies were introduced in this paper. Aerodynamic noise can be classified into rotational aerodynamic noise such as jet engine fans or helicopter rotors and general aerodynamic noise such as high speed jet noise, high speed air flow inside piping, and external noise from vehicles, cars and aeroplanes. The aerodynamic noise of the air flow radiated from a wind tunnel exit was caused more or less by the pressure fluctuation of a boundary layer in a high frequency wave region. In checking the noise generated from a difference in level, projection, cavity, opening, etc., of a high speed vehicle in a wind tunnel test, the noise was louder in the case of a difference in level where the downstream side was raised. The finding was similar with projections. In the rear of a super sonic choke part, a strong flow was generated and became a violent noise source when a flow was overexpanded and a pressure was recovered with a sonic boom. However, the noise was greatly reduced by installing a porous material such as a porous metal immediately behind the choke part. An active control of noise was carried out by changing a sound field characteristic against aerodynamic self-excited noise with a speaker. 32 refs., 11 figs.

Research on harmonized molecular materials; Bunshi kyocho zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Harmonized molecular materials (HMM) were researched to create functional materials adaptable to needs such as environmental harmony and high-efficient conversion in post-industrial society and aging society. Superior mechanisms function efficiently in organisms for perception, transmission and processing of information, and transport and conversion of substances. These functions are caused by harmonization between organic molecules, or organic molecule and metal or inorganic substance. HMM is a key substance to realize these functions similar to those of organisms artificially. It is the purpose of this research to develop HMMs, reform production process by innovating separation and conversion technologies, and finally realize molecular chemical plants. This research also develops high-efficient devices to contribute to the information society, and progresses the industry of bio-functional materials such as high-sensitive bio-sensor. The functions, applications and creation technologies of three kinds of HMM such as assembly, mesophase and microporous materials were researched in fiscal 1995. 956 refs., 128 figs., 13 tabs.

FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 9. Research and evaluation of innovative and leading technologies; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 9 (kakushinteki, sendoteki gijutsu ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to make useful suggestions and proposals for the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project and thereby to promote the research and development activities, the innovative and leading technologies have been studied, investigated and evaluated. In FY 1998, a total of 6 proposals were collected, and evaluated to prioritize for the conceptual studies. These are related to methanol-fueled power generation turbine system, conceptual design of high-efficiency production system for high-efficiency solar cell by the 10 GW/y scale production process, investigation of potential of wind power, CO2 recycling methanol fuel cell, investigation of catalysis materials for hydrogen combustion and catalytic combustion systems, development of reversible high-temperature steam electrolysis cell/solid oxide fuel cell by the synthesis from aqueous solutions, and mobile heat recovery hydrogen production system. Promising technologies to be reflected on the WE-NET project were examined, based on the new technologies acquired from the research and investigation so far. As a result, two candidates were selected; hydrogen liquefaction by magnetic refrigeration technology, and catalytic combustion gas turbine. (NEDO)

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 2. Research on safety measures; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 2. Anzen taisaku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 WE-NET phase 2, task 2 research result on safety measures. In the study on preparation of the safety design standard, based on the concept design of the hydrogen supply station under investigation in task 7, latent anomalies and accidents, safety measures against them, and precautions for the safety design were arranged. Survey was made on databases available to collect failure rates necessary for quantitative risk assessment. In the study on establishment of a safety evaluation method, an evaporation apparatus for liquid hydrogen was prepared for comparative experiment with liquid nitrogen. Various information on flow and evaporation properties of liquid hydrogen were obtained. Survey was made on previously reported documents for hydrogen explosion experiment and preparation of an experiment plan. The simulation model for spillage, evaporation and diffusion of liquid hydrogen was verified and improved on the basis of the experiment results. A commercially available computation program for hydrogen deflagration was introduced, and its implementation was studied. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Items of information were collected on development of technologies to put photovoltaic power generation systems into practical use, the international cooperation projects, and the IEA photovoltaic power generation program. This paper summarizes the achievements in fiscal 1999. In the activities of IEA/REWP/PVPS in the current fiscal year, the 13th and 14th Executive Committee meetings, and the 3rd Executive Conference were held. The Task 1 has performed such activities as ISR, NSR, Newsletters, and opening the Internet homepage. The Task 2 activities included structuring about 260 databases for the operation characteristics of photovoltaic power generation systems, and completing the internal material handbooks on measurement and monitoring. A new work plan was prepared for the Task 3 regarding an independent photovoltaic power generation plant for use in an island. For the building integrated photovoltaic power generation system in the Task 7, survey activities were executed by utilizing expertise conferences on building designs, system technologies, and non-technical impediments. In the feasibility survey and research on large-scale photovoltaic power generation utilizing unused land such as desert for the Task 8, the programs were established. (NEDO)

Fiscal 1999 technical survey report. Basic project on international cooperation on energy consumption improvement, etc. (Japan International Cooperation Center project on promotion of exchange of specialists); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Kokusai kyoryoku center jigyo suishin senmonka koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Specialist related to the governments of Thailand, Malaysia, and Indonesia where NEDO (New Energy and Industrial Technology Development Organization) implements its model projects were invited. They exchanged opinions with officials of the Japanese Government and affiliated organizations over measures for effective energy utilization. Opinions were also exchanged over the response of energy-consuming industries, development of technologies, and the status of their adoption. Activities of government-related participants are described below. Under a Model Project for Utilization of Waste Heat from Incineration of Industrial Waste at Industrial Estate, five Thai people with Industrial Estate of Thailand visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Keiyo Food Industrial Park. Under a model project on the recovery of waste heat from paper sludge incineration, four Malaysian people with Ministry of Energy, Communications and Multimedia or with Energy Center visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Japan Paperboard Industries Co., Ltd. Under a model project on the utilization of paper sludge and solid waste, four Indonesian people with Ministry of Industry and Trade or with Ministry of Mines and Energy visited Ministry of International Trade and Industry, NEDO, Babcock-Hitachi K.K., and Oji Paper Co., Ltd. (NEDO)

Record of the Japan - U.S. Energy Discussions / Maui Meeting. March 25-27, 1996; Nichibei energy kyogi Maui kaigi. 1996 nen 3 gatsu 25 nichi - 27 nichi

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-25

The paper summarized the status of the Japan-U.S. Energy Discussions held in the Maui Island during March 25-27, 1996. With relation to the energy supply, reported and discussed were the present situation in the Middle East, Russia, Ukraine, and the former U.S.S.R. and effects of the political situation on the world. The paper also described effects of the intergovernmental resolutions on climate change on the energy issue. In addition to comprehensive prospects in the energy field, reported and discussed were issues related to coal, electric power, nuclear power, petroleum, gas and renewable energy. The following were generally commented on: There are uncertainties and unclearability in the future energy field in terms of politics, technology and environment, and in order to quickly respond these, dialogue of a global scale is necessary. In the energy industry, it is important to pursue effectiveness by the price mechanism, the market, and governmental policies. The international cooperation is much more needed, and the Japan-U.S. cooperation is desirable especially in the fields of stabilization of international politics, promotion of technical innovation, assistance for environmental orientation in developing countries, proposal of politics, etc.

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 2. Research study on promotion of international cooperation; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 2. Kokusai kyoryoku suishin no tame no chosa kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes the research result on promotion of international cooperation in the WE-NET project in fiscal 1996. The WE-NET project aims at development of the total system for hydrogen production, transport, storage and utilization, and construction of the earth-friendly innovative global clean energy network integrating elemental technologies. Since the standpoint is different between latent resource supplying countries and technology supplying countries, the WE-NET project should be constantly promoted under international understanding and cooperation. The committee distributed the annual summary report prepared by NEDO to overseas organizations, and made positive PR activities in the 11th World Conference and others. The committee made the evaluation on the improvement effect of air pollution by introducing a hydrogen vehicle in combination with Stanford University, and preparation of PR video tapes for hydrogen energy. Preliminary arrangement of Internet home pages, establishment of a long-term vision for international cooperation, and proposal toward the practical WE-NET are also made. 9 figs., 13 tabs.

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. International cooperation project Collection of information on IEA wind power research and development program; 1999 nendo taiyoko hatsuden systsem jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo seika hokokusho. IEA furyoku kenkyu kaihatsu program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Participation was taken place in the executive committee for the implementation agreement of the IEA wind power research and development and other task workshops to investigate the status of research and development of wind power generation systems in other countries. The contents of the main activities under the implementation agreement of the IEA wind power research and development include researches on innovative technologies, analysis of the state-of-art wind power technologies, exchange of technological information, and expansion of the cooperation with industries, electric power operators, and non-IEA member countries. The agreement is participated currently by 17 countries and 19 contracted organizations from EC. The participants to the IEA R and D wind implementation agreement are taking activities in the tasks called the annexes. The activities of the annexes include exchange of fundamental technological information, annual generalization of the promotion of wind power energy utilization in the countries participated in the IEA implementation agreement, round-robin tests of windmills, and expansion of the wind characteristics database and the database for field rotor aerodynamics. Publications that have been issued include the 'Annual report', and newsletters issued once to twice annually. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use (International cooperation project - collection of information on IEA photovoltaic power generation program); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development, verification, analysis and information exchange have been performed based on the 'Treaty to Execute the Research and Cooperation Program on Photovoltaic Power Generation System'. The IEA/REWP/PVPS activities in fiscal 1999 include the participation to the two executive committee meetings (Valencia and Sydney), and the subcommittee activities. The subcommittee activities are as follows: Task I: information exchange on and proliferation of the photovoltaic power generation systems, Task II: operation performance and design of the photovoltaic power generation systems, Task III: design and operation of the independent type and the island use power plants, Task VII: Building integrated photovoltaic power generation systems, Task VI, Sub-task 5: investigations and researches on possibility for photovoltaic power generation systems utilizing unutilized lands including deserts, and Task IX: technical cooperation to expand photovoltaic power generation system markets. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use (International cooperation project - collection of information on IEA photovoltaic power generation program); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development, verification, analysis and information exchange have been performed based on the 'Treaty to Execute the Research and Cooperation Program on Photovoltaic Power Generation System'. The IEA/REWP/PVPS activities in fiscal 1999 include the participation to the two executive committee meetings (Valencia and Sydney), and the subcommittee activities. The subcommittee activities are as follows: Task I: information exchange on and proliferation of the photovoltaic power generation systems, Task II: operation performance and design of the photovoltaic power generation systems, Task III: design and operation of the independent type and the island use power plants, Task VII: Building integrated photovoltaic power generation systems, Task VI, Sub-task 5: investigations and researches on possibility for photovoltaic power generation systems utilizing unutilized lands including deserts, and Task IX: technical cooperation to expand photovoltaic power generation system markets. (NEDO)

Report on investigations in fiscal 2000. International infrastructure improving project for rationalization of energy use (Fundamental survey on effective utilization of unutilized biomass energy in ASEAN countries); 2000 nendo kokusai energy shiyo gorika kiban seibi jigyo chosa hokokusho. ASEAN shokoku ni okeru miriyo baiomasu energy no yuko riyo ni kansuru kisochosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to utilize 'biomass' being the unutilized and reproducible energy source, which exists affluently in the ASEAN countries, investigations and discussions have been carried out on electric power generation using palm shells as fuel in Malaysia. This paper reports the achievement in fiscal 2000. The biomass energy plant project was discussed with the followings as the conditions: an output of 1 MW, use of biomass in the form of wastes discharged from oil palm mills, the system of direct combustion process with boiler/steam turbine generation process, and power transmission to public grids. As a result of the discussions, the following conclusions were obtained: reduction of greenhouse effect gas exhaust will amount to 81,540 t-CO2/year, reduction will be realized on white smoke pollution caused by wastes incineration being criticized from various sectors and such harmful gas exhaust as SOx and NOx discharged from fossil fuel power generation, the uncertainty of electric power supply currently depending on DG power generation will be mitigated resulting in acquisition of economic effects, and electric power supply to 1,000 households will be possible, contributing to enhancement of living standard due to electrification. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. International cooperation project Collection of information on IEA wind power research and development program; 1999 nendo taiyoko hatsuden systsem jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo seika hokokusho. IEA furyoku kenkyu kaihatsu program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Participation was taken place in the executive committee for the implementation agreement of the IEA wind power research and development and other task workshops to investigate the status of research and development of wind power generation systems in other countries. The contents of the main activities under the implementation agreement of the IEA wind power research and development include researches on innovative technologies, analysis of the state-of-art wind power technologies, exchange of technological information, and expansion of the cooperation with industries, electric power operators, and non-IEA member countries. The agreement is participated currently by 17 countries and 19 contracted organizations from EC. The participants to the IEA R and D wind implementation agreement are taking activities in the tasks called the annexes. The activities of the annexes include exchange of fundamental technological information, annual generalization of the promotion of wind power energy utilization in the countries participated in the IEA implementation agreement, round-robin tests of windmills, and expansion of the wind characteristics database and the database for field rotor aerodynamics. Publications that have been issued include the 'Annual report', and newsletters issued once to twice annually. (NEDO)

Investigation research on autonomous responsive materials; Jiritsu oto zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A survey was made on autonomous responsive materials as a new material which reversibly change molecular structures and the aggregation state according to external stimuli. Autonomous responsive materials imitate environmental responsibility in the living organism system and have sensing, control and active functions for external stimuli. The materials are highly efficient and environmentally friendly. In biomimetic materials for soft actuators, drastic changes by temperature of elastic modulus of water-swollen hydrogel are used to the motion. In order to molecularly design stimulus-responsible polymer gel, studied are the relation between the micro structure and stimulus responsibility, dynamic correlation between the micro structure and the macro structure, etc. In the biomedical field, new cure and diagnosis using innovative materials are expected, and the application of autonomous responsive materials to the field is studied. For example, using hydrogel responding the temperature and the surface and controlling by temperature the interaction with components of the organism such as protein and cells, drug delivery in the organism is optimized. Also studied is the application of hydrophilic/hydrophobic changes by temperature to the chromatography. 215 refs., 47 figs., 11 tabs.

Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

2000-03-24

Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

Recent surveys and researches on pollinosis in Japan; Kafunsho ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shido, T. [The Inst. of Public Health, Tokyo (Japan)

1998-05-31

In this paper, recent investigations and researches on pollinosis are summarized as centering on the investigation entrusted by the Ministry of Health and Welfare and executed since 1992, and especially the surveys on Japanese cedar pollinosis during 1995 to 1996. The quantity of pollen surveyed in 1995 is the greatest in the survey history of nationwide flying pollen. Particularly, the quantity of cedar and hinoki pollen is 10 to 40 times as many as that in the year before. Consequently, since the sensitization and onset due to the cedar pollen increased greatly, the objects of the surveys and the researches were mainly in respect to the analysis of onset factors of pollinosis, clarification of its natural process, evaluation on the effectiveness of desensitization therapy, the clinical subjects including the confirmation of pharynx symptom and asthma symptom, and the discovery of naturally sensitizing dog. A fact that the quantity of flying pollen concerns the occurrence and degree of the clinical symptom has already been indicated by a clinical observation carried out for a long period of time. In respect to specific prophylaxis and therapy, for the first time the pollen masks and glasses sold on the market are investigated, and the necessity of the verification thereof is described. 27 refs., 7 figs., 5 tabs.

FY 2000 Project of developing international standards for supporting new industries. Comprehensive study for promotion of the international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru hokatsuteki chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project studies the schemes for the international standardization, trends of the international standardization by the international standardization organizations and related organizations, and activities for the international standardization by the enterprises in the advanced countries, among others, in order to promote the international standardization for the 8 research and development themes. These themes are SMIL (synchronized multimedia integration language) tag standard of the three-dimensional image data, based on MXL; systems for detecting gene recombination products; methods for testing mileage of gas-fueled automobiles; measurement of multi-colors; testing/evaluation methods for highly coherent lasers; methods of evaluating optical performance of microlenses for optical information processing; recycled CFRPs; and devices for measuring marine environments. The study results indicate that progress of the development of the international standardization of the advanced technologies can be followed by investigating the characteristics of the ISO publications; ISO is studying the business plans being developed by each TC, in order to improve market adaptability of the international standards; and the European countries add conditions for standardization when the research and development themes are contracted. (NEDO)

Report of 22nd International Symposium on Shock Waves; Dai 22 kai kokusai shogekiha symposium shusseki hokoku

Energy Technology Data Exchange (ETDEWEB)

Takayama, K. [Tohoku Univ., Sendai (Japan). Inst. of Fluid Science

1999-11-05

Outlined herein are the topics at the 22nd. International Symposium on Shock Waves, held in July 1999 in London. Prof. Takayama of Tohoku University gave an invited lecture on application of shock waves to medical area, stressing significance of shock waves on a human body. A total of 81 papers were presented from Japan. Number of Japanese papers and number of Japanese attendees both accounted for approximately 25%. The themes of these papers are centered by behavior of shock waves (e.g., propagation, reflection, and diffraction), extreme supersonic flows, interference between shock wave and boundary layer, aerodynamics (e.g., interference between vortex and shock wave), numerical simulation of shock wave phenomena, development of a new shock wave tube and measurement method, researches on elementary steps in chemical reactions, shock wave phenomena in condensed media and multi-phase media, shock wave noise produced while a high-speed train is running in a tunnel, and application of shock waves to industrial and medical areas. Japan contributes much to the application to medical area, and a method dispensing with injection is reported. Japan's aerospace-related researches include interference between shock wave and boundary layer, in which the real gas effect is taken into consideration, designs for protection from heat during the re-entry into the atmosphere, and construction of the world largest free-piston type wind tunnel. (NEDO)

Committee for international collaborative research of medical and welfare apparatus; Iryo fukushi kiki kokusai kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper summarized activities for an investigational study on the international collaborative research project on the medical and welfare apparatus implemented in fiscal 1995. As investigation activities, the second meeting of information exchanges with E.U. and three north European countries was held following the meeting in fiscal 1994, and at the same time, information exchanges were made with organizations/institutions of industry/government/university in Germany, France and Canada. The study made it clear that Europe is also taking a direction of low-degree action diagnosis/care as Japan is. Further, concrete exchanges of information advanced and an awareness of the common issues was made clear such as the necessity of developing apparatus which meets the apparatus market and users` needs. As international collaborative activities, new methods of information exchanges were adopted such as the satellite meeting of the International MR Society, meetings with researchers who visited Japan. The satellite meeting of the International MR Society was favorably accepted by participants, and it was pointed out that it is important to continue the meeting in view of the materialization of themes, etc. 4 refs., 32 figs., 5 tabs.

Project to promote exchange of international information on environmental technologies; Kankyo gijutsu kokusai joho koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Mutual information exchange at international levels is important for practical application of global environment preservation technologies, whereas the APEC Virtual Center was established in fiscal 1997. Fiscal 1998 has discussed the future functions of the Virtual Center, and carried out the following matters to improve the functions and achieve its stable operation. Discussions were given on common use with the centers of other countries and regions of the specifications of classification systems for information areas and provided information that are provided by the Virtual Center. Visits were made to sub-managing countries and regions for smooth operation of the study groups, and opinions were exchanged. Visits were made to coordinators and contact points established in each country and region when the Center was founded in fiscal 1997. A visit was made to the U.S. Environmental Protection Agency to exchange opinions on coordination measures with the Cleaner Production Strategy of the U.S.A. being a project similar to the subject project. In order to strengthen the Japan's Center, attempts were made to expand the linking information to wider scope. Special pages publishing concentratedly the items of information that the users are interested were prepared as part of the information provision. (NEDO)

Study on the reaction mechanism of oxygen-added enzymes for the effective utilization of unused sea weeds; Miriyo kaiso no shigenka ni kansuru sanso tenka sanso no hanno kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To effectively utilize unused sea weeds having ingestion obstructing activities for feed, the treatment by oxygen added enzyme has been investigated. Undaria pinnatifida was pasted and solidified with agar, to prepare the standard feed. Individuals of Holiotis discus hannai Ino were bred in the cistern. Extracts from ten kinds of sea weed distributed in the Sanriku Coast were added to the feed, which were compared with the standard feed to determine the ingestion obstructing activities. A testing method using cellulose painted aluminum sheet was also employed. All of the extracts from sea weeds having the ingestion obstructing activities exhibited the strong phenol reactions. The sensitivity of individuals of Holiotis discus hannai Ino depended greatly on the derived species and the chemical structures of phenolic substances. The {alpha}-hydroxymuconic acid semialdehyde (HMS), an enzyme decomposition product of catechol, provided no ingestion obstructing activity, and showed a little ingestion accelerating activity. This was considered to become ingestible through the biodegradation of phenolic substances. The HMS, a decomposition product of catechol 2,3-oxygen added enzyme derived from the petroleum decomposition bacteria, was prospective as a highly functional compound synthesizing material. 10 refs., 34 figs., 10 tabs.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on Task 9 in IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports activities performed by the Task 9 in the execution treaty of the IEA photovoltaic power generation system program. The Task 9 calls for the 'proliferation of photovoltaic power generation technologies under coordination with developing countries{sup .} It is intended to compile the recommendation guides, hold workshops in the model developing countries, and coordinate with assisting organizations on technological and economical issues that may occur when introducing photovoltaic power generation systems into developing countries. The current fiscal year is the first year of the five-year plan, whereas, with structuring the basic plan placed in the center, such activities were carried out as verification of the 12 member countries and two organizations, establishment of the basic programs for the work plan, selection of work divisions, the sharing thereof, and the subjected developing countries, and the way the coordination should be with the related tasks and the assisting organizations. Two expertise conferences were held in Holland and America, and three working group meetings in Japan to have discussed the activity targets in the first fiscal year. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on Task 9 in IEA photovoltaic power generation program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports activities performed by the Task 9 in the execution treaty of the IEA photovoltaic power generation system program. The Task 9 calls for the 'proliferation of photovoltaic power generation technologies under coordination with developing countries{sup .} It is intended to compile the recommendation guides, hold workshops in the model developing countries, and coordinate with assisting organizations on technological and economical issues that may occur when introducing photovoltaic power generation systems into developing countries. The current fiscal year is the first year of the five-year plan, whereas, with structuring the basic plan placed in the center, such activities were carried out as verification of the 12 member countries and two organizations, establishment of the basic programs for the work plan, selection of work divisions, the sharing thereof, and the subjected developing countries, and the way the coordination should be with the related tasks and the assisting organizations. Two expertise conferences were held in Holland and America, and three working group meetings in Japan to have discussed the activity targets in the first fiscal year. (NEDO)

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which IEA international cooperation project; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi IEA kokusai kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper summarizes the activities related to the Annex II 'Communication technology for DSM' in the international cooperation agreement on the DSM program by IEA. With regard to the 'needs in relation with DSM and the related functions and the communication technology between the demand side and the electric power companies required for the execution thereof', a survey has been made by sending question letters to ten membership nations, which has been compiled into a report. With respect to the 'evaluation on the method for international cooperation on standardization of the communication technology', replies to the question letters from the membership nations were analyzed. Decisions were given on the standards directly related to the communication technology for DSM, the standard drafting organizations, and the working groups. With regard to the 'evaluation on priority on research, development and demonstration of the communication technology for DSM', propositions were given as the project on the technology for communications inside a building for DSM and the related functions, development and transfer of DSM and the related functions from the communication media for a narrow band to a wide band, and specifications for the customers' terminals. In developing the general purpose personal computer software 'eaCOMMS', distribution and discussions were given on the trial edition. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. International cooperation projects (Collection of information on IEA photovoltaic air conditioning and hot water supply program); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Kokusai kyoryoku jigyo (IEA taiyo reidanbo kyuto program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports activities of collecting items of information by dispatching experts mainly composed of members of the IEA photovoltaic air conditioning, and solar heating and cooling program (SHCP) committee to the SHCP Executive Committee and the Task expert conferences. This treaty is intended to assist creating the environmentally sustainable future by utilizing solar designs and technologies. It also aims at developing solar technologies including cost reduction as a result of the joint researches with business entities, structuring international markets, providing items of information, quantifying the effectiveness to the environment, performing the international standardization, and promoting utilization of solar technologies in developing countries. The tasks now in action include architectural lighting, methods for analyzing solar architectural energies, optimization of solar energy utilization in large buildings, procurement of active solar systems, air conditioning systems in buildings using the solar energy, solar heat composite systems, expansion of exterior component materials for solar buildings, sustainable buildings, agricultural solar drying, solar cities, a hybrid heat/PV solar system. (NEDO)

FY 1999 project on the development of new industry support type international standards. Comprehensive survey research on the promotion of international standardization; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of promoting the international standardization effectively/strategically, a comprehensive survey was made, and the FY 1999 results were summarized. In the trend survey on the comprehensive international standardization, survey was conducted for companies in the material field (plastics, rubber and iron steel) and in the mechanical field (robot, machinery, aircraft, etc.). As a result of the survey, it was found out that they have few headquarters systems and experts, but they tackle it strategically and defensively, taking the standardization as business. Also as to the trend of CEN/CENELEC, importance of the continued trend survey was pointed out. In the survey of policy for the international standardization, survey was carried out on the trend of the process for working out the international standards (TS, ITS and SDO). Further, in relation to the technology standards and intellectual property rights in the hi-tech field, survey was made on the present situation of rules for handling intellectual property rights of organizations, groups, etc. for standardization, how to handle intellectual property rights in the standardization process, problems and the solution, etc. (NEDO)

Systematic analysis on mooring systems of floating structures; Futai keiryuho ni kansuru keitoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K; Suzuki, H; Ide, T [The University of Tokyo, Tokyo (Japan)

1997-12-31

Discussed herein are mooring performance requirements of the new types of marine structures now proposed, and characteristic ranges and future expansion potential of the existing mooring systems. The mooring systems studied for floating structures are catenary, single point (multi-leg and single-leg types), fixed structure with fender and tension leg mooring systems. The studied items include extraction of the elements that constitute rigidity of the spring for horizontal mooring, survey on and data collection for each element, determination of element ranges, programs for mooring analysis, assessment of mooring characteristic ranges, and potential development of the characteristic ranges. It is concluded that the existing systems with their current characteristic ranges and future possibility are insufficient for the future marine structures. It is therefore necessary to develop new mooring concepts, instead of expanding the current concepts, in order to meet the mooring performance requirements for the new marine structures. 14 refs., 9 figs., 11 tabs.

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Layered multinary lanthanum oxide [La-Mo-O]; Sojo rantan fukugo sankabutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Studies have been carried out systematically on properties of oxides including representative transition metal, vanadium, and alkali metals. With respect to Ln2CuO4 (Ln is a rare earth element) being a simple and representative rare earth multinary oxide showing superconductivity, and its related compounds, this paper reports thermal chemistry, superconduction, and making them a superconductor by using soft chemical treatment. The paper also reports centrally on synthesis of new copper oxide superconductors under high pressure, the compositions, structures, superconductive properties of the synthetics, and the relationship between them. It describes phase equilibrium, synthesis, and structures of vanadium multinary oxides being the object of continued studies, and also reports the studies related to structure and phase transfer of NaV6O11 which shows especially interesting properties among the oxides. Studies have also been made on NMR of these compounds and copper oxide superconductors by using magnetic resonance. The paper also describes a method to analyze the structure of quasi-crystal having rotary symmetry which is not allowed in crystals, and has special long-distance order phase. 209 refs., 127 figs., 6 tabs.

Relationship between stacking process and resolution; Jugo shori to bunkaino ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsushima, J; Rokugawa, S; Kato, Y [Geological Survey of Japan, Tsukuba (Japan); Yokota, T; Miyazaki, T [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1996-10-01

This paper evaluates influences of stacking of incident angles against the reflecting surface on the resolution. Basic equations for evaluating the influences were deduced. A simple evaluation method has been provided using these equations. The present evaluation method is considered to be useful for acquisition design, processing, and interpretation of data as an indicator. According to the equations introduced in this study, there are some demerits for stacking traces whose incident angles were large. A total reflection region often appears due to the decreased resolution, and the vertical resolution decreases prior to stacking. Occasionally, it is not effective to remove traces having large incident angles from the viewpoint of resolution. In practice, the selection of most suitable trace through trial and error is not easy due to difference in individual regions. An evaluation method must be discussed, by which the optimal trace can be selected automatically during the data processing. 6 refs., 15 figs.

Study on accretion of ice on oscillating aerofoils; Shindoyokujo no chakuhyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishikawa, S; Sugihara, H [Kandenko Co. Ltd., Tokyo (Japan); Kimura, S; Sugiyama, Y [Kanagawa Institute of Technology, Kanagawa (Japan); Tsuboi, K [Ibaraki University, Ibaraki (Japan). Faculty of Engineering

1997-11-25

The effects of pitching and heaving motions of an aerofoil on accretion of ice thereon are investigated for the design of wind turbine blades. The conditions under which an aerofoil shows a heaving motion are 10m/s as wind velocity, -12degC as ambient temperature, 0.5Hz as frequency and 5mm as amplitude. Initial growth of ice is stochastic to a great extent; ice grows rapidly around the seed which is formed by chance somewhere on an laerofoil. The effects of ice appear in the flow field in the vicinity of the aerofoil front edge, as it continues to grow, providing different conditions for water droplets to collide with each other. Average ice shapes can be classified by environment, although at low repeatability. Range of ice accretion varies depending on aerofoil motion, whether it is pitching, heaving or at rest. The most important factor that determines behavior of ice accretion is conditions of the flow field near the aerofoil front edge. In a pitching or heaving motion, its speed is an important factor for growth of ice. 2 refs., 5 figs.

Study on reduction method of brake squeal; Brake naki teigen shuho ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Nakajima, T; Okada, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

The reduction of brake squeal is an important technological subject in terms of making vehicles quieter. In our research, we carried out a modal analysis from the caliper to the installation bracket during generating brake squeal to identify the places that influence the squeal. Based on this, we studied proposals to reduce the squeal, and have reduced the squeal noise at about 5 kHz as reported in this paper. 1 ref., 12 figs.

Systematic analysis on mooring systems of floating structures; Futai keiryuho ni kansuru keitoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K.; Suzuki, H.; Ide, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

Discussed herein are mooring performance requirements of the new types of marine structures now proposed, and characteristic ranges and future expansion potential of the existing mooring systems. The mooring systems studied for floating structures are catenary, single point (multi-leg and single-leg types), fixed structure with fender and tension leg mooring systems. The studied items include extraction of the elements that constitute rigidity of the spring for horizontal mooring, survey on and data collection for each element, determination of element ranges, programs for mooring analysis, assessment of mooring characteristic ranges, and potential development of the characteristic ranges. It is concluded that the existing systems with their current characteristic ranges and future possibility are insufficient for the future marine structures. It is therefore necessary to develop new mooring concepts, instead of expanding the current concepts, in order to meet the mooring performance requirements for the new marine structures. 14 refs., 9 figs., 11 tabs.

Research study on harmonized molecular materials (HMM); Bunshi kyocho zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As functional material to satisfy various needs for environmental harmonization and efficient conversion for information-oriented and aging societies, HMM were surveyed. Living bodies effectively carry out transmission/processing of information, and transport/conversion of substances, and these functions are based on harmonization between organic molecules, and between those and metal or inorganic ones. HMM is a key substance to artificially realize these bio-related functions. Its R & D aims at (1) Making a breakthrough in production process based on innovation of material separation/conversion technology, (2) Contribution to an information-oriented society by high-efficiency devices, and (3) Growth of a functional bio-material industry. HMM is classified into three categories: (1) Assembly materials such as organic ultra-thin films (LB film, self-organizing film), and organic/inorganic hybrid materials for optoelectronics, sensors and devices, (2) Mesophase materials such as functional separation membrane and photo-conductive material, and (3) Microporous materials such as synthetic catalyst using guest/host materials. 571 refs., 88 figs., 21 tabs.

Survey on the international cooperation for resonable use techniques of energy; Energy shiyo gorika shuho kokusai kyoryoku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

LCA (life cycle assessment) is known as one of the techniques for assessing reasonable use of energy considering environment. Usefulness of LCA was examined by checking the consistency between the assessment result on refrigerators by LCA and ISO standards. LCA can digitize the data on energy substances, wastes and emission of the whole system. LCA is useful for effective use and control of resources, and to clarify the reduction chance of environmental impacts. However, the framework is necessary to estimate the accuracy of assessment technique for every category, and the reliability of influence assessment. Like a risk assessment for environmental damages, identification of discharge sources beyond the assessment function of potentials is difficult. As the viewpoint of the whole life cycle is important, assessment of local damages is difficult. The complementary use of LCA and other tools about sustainable development is important. The comparison result between ISO provisions and this LCA case study showed that this concrete research report can play a role as text book for the ISO technique. 74 refs., 38 figs., 45 tabs.

Fiscal 1998 report on Japan-Asia international cooperation project; 1998 nendo Nichi Asia kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

For the development of talent, industrial infrastructures, and new industries in countries that received Japanese cooperation, Japanese researchers were sent to universities and research organizations in Asian countries, where they were engaged in joint research and development, which involved (1) micro device technology, (2) technology for manufacturing industrial silica material by chaff incineration, (3) technology for forming and machining of alloys difficult to machine, light in weight, and high in strength, (4) technology for rare metal isolation and refining, (5) cascade-wise utilization and practical application of biomass in Asia, (6) exploration and utilization of microbial resources in Tropical Asia, (7) evaluation of biological resources existing in Southeast Asia and construction of information network, (8) development and evaluation of cultured articular cartilage, (9) technology for utilizing wastewater for production of valuable substances, and (10) studies for utilizing biological resources through utilization of diversity of symbiotic microbes and their adaptability to surroundings. Under item (1), it was planned that ultrasonic micro transducers and micro fluid devices be developed for use in the medical field. (NEDO)

`Joint Research and Development of Industrial Technology,` an international research collaboration for fiscal 1997. Utilization of 3D-woven C/C composite materials to machine components; 1997 nendo kokusai kenkyu kyoryoku jigyo `sangyo kiban gijutsu kyodo kenkyu kaihatsu`. Sanjigen ori C/C composite zairyo no kikai buhin eno oyo ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A polygonal mirror in a printer and the main shaft of a high-speed milling machine are used as models for the development of technology for applying C/C (carbon/carbon) composite materials to machine components that are required to turn at high speeds. Various C/C composites are tested for flexural strength and thermal expansion for the designing and manufacturing of C/C composites for the polygonal mirror and main shaft. The first coating on the C/C composite is deposited by laser/plasma hybrid spraying, and is a Mo coating. A spraying robot is experimentally built for homogeneous coating. In the case of polygonal mirror, an Al coating is deposited further by the gas-deposition method. The polygonal mirror proves excellent in both dimension and reflectance, and attains the target speed of 45,000rpm. In the case of milling machine main shaft, however, it is not strong enough to withstand 40,000rpm although it is a success from a viewpoint of coating technology and manufacturing technology. 15 refs., 33 figs., 13 tabs.

Achievement report for fiscal 2000 on the phase II research and development for the hydrogen utilizing international clean energy system technology (WE-NET). Task 1. Investigations and researched on system assessment; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-1. Technologies drawing attentions relate to fuel cell driven automobiles and hybrid automobiles in the field of utilizing hydrogen derived from reproducible energies and fossil energies, and fuel cell co-generation and micro gas turbine co-generation in the field of electric power generation. Hydrogen reformed from gasoline on board the automobile as the fuel for fuel cell driven automobiles, hydrogen as a by-product of coke furnace off-gas (COG), and reproducible energy hydrogen have the same fuel consumption performance as in the hybrid automobiles. Particularly the COG is low in cost, and has large supply potential. Liquefied hydrogen is as promising as compressed hydrogen in view of the cost for automotive hydrogen supply stations. What has high economic performance as the self-sustaining systems for islands are photovoltaic and wind power generation, and the system using hydrogen as the secondary energy. Since much of the reproducible energies is used for electric power demand in Japan, the by-product hydrogen and the reformed hydrogen in an amount of 9.3 billion Nm{sup 3}/year would take care of majority of the demand in view of the short time period. For a longer time span, hydrogen originated from the reproduced energies in the Pan-Pacific Region should be introduced. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 2. Investigations and researched on safety measures; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 2. Anzen taisaku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-2, the safety measures. In order to structure safety design criteria, potential anomalies, accident phenomena, and safety measures that can be applied were put into order based on the conceptual designs on hydrogen supply stations. Items of information were collected and put into order on failure rates and other factors to estimate accident occurrence frequency required for quantitative risk assessment. Representative event scenarios were selected by estimating the event evolving processes. In order to obtain knowledge about the steady state of run-off and evaporation of liquefied hydrogen, experiments were performed by using a small-size experimenting device, whereas new findings were discovered. To identify the fundamental knowledge related to explosion of hydrogen, and to verify a program simulating the explosion, explosion experiments were inaugurated to have established the stable experiment performing method. A calculation program simulating leakage and evaporation of liquefied hydrogen was verified and analyzed from the experimental results, and the program improvements were discussed. Pre-estimation and verification were carried out on the explosion experiments by using the hydrogen explosion and combustion simulating calculation program, and discussions were given on program improvement. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 12. Search and assessment of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 12. Kakushinteki sendoteki kenkyu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Search and assessment were carried out on innovative and leading technologies which are outside the development objects at the present, but are promising for the future. This paper describes the achievements in fiscal 2000. In the hydrogen manufacturing method using natural gas as the raw material, but not generating carbon dioxide, a method using plasma has the hydrogen conversion rate of more than 90%, capable of providing carbon black with added value. On a hydrogen selective enzyme hydrogenase sensor, verification was given on its sensitivity and response speed, but the discussion was interrupted because of difficulty in obtaining the enzyme. Naphthenic hydrogen storage and transportation media (easy in hydrogenation and dehydrogenation) were discussed, whereas the reaction promoting effect was identified in both of the super heating liquid film process and the membrane reactor system. Enhancement in output and efficiency may be anticipated if hydrogen-rich reformed gas is obtained by reforming methane (natural gas) by utilizing waste heat from a gas turbine of several MW capacity. Hydrogen liquefaction technologies using the magnetic freezing process was discussed as the fundamental research assignment, wherein fiscal 2000 has studied the basic design and optimal magnetic materials. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (Collection of the information on the IEA photovoltaic power generation program); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information on the photovoltaic power system was made, and the FY 2000 results were summarized. In Task I: Exchange of the information on the photovoltaic power system and the spread, the final report on 'the study on added values of PV system' was made. In Task II: Operational performance and design of the photovoltaic power system and subsystem, specifications for new database were determined, and the existing data were checked/revised/added. In Task III: Design and operation of the stand-alone type and remote island use photovoltaic power plant, survey was conducted of the present situation of technical standards and quality guarantee. In Task 7: Photovoltaic power system integrated with construction materials, work was done for making a book of installation samples of the PV system integrated with construction materials in each country. In Task 8: Investigative study of possibilities of the large-scale photovoltaic power generation using the unused land such as desert, a report making of the secondary survey was started. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Rinsangata nenryo denchi no kasoku jumyo shiken hoho no hyojunka ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As for fuel cells, which are expected as a new clean energy, the R and D are being proceeded with in various fields of the world, but the standardization has not been made both in Japan and abroad. In Japan, the situation is that the information on technical terms, indication method, performance test method, and environment/safety test methods of the phosphorous acid fuel cell power generation is publicly spread. In relation to the international promotion of fuel cells to be predicted, it is necessary to internationally standardize cells themselves which are a key component of fuel cell power generation facilities. Phosphorous acid fuel cells are expected of the earliest commercialization of all, but the common test method to evaluate life characteristics of the cell stack has not been established yet. In the R and D, for the purpose of internationally standardizing test methods to evaluate life characteristics of the cell stack, a study on the acceleration life test method of phosphoric acid fuel cells was conducted in terms of the technical trend, data, standard, etc. A plan was prepared on general rules of the method to test acceleration life at the cell reaction part of the small cell, and activities also were started for setting up a technical committee for the fuel cell power system in President`s Advisory Committee on Future Technology. 29 figs., 20 tabs.

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (Collection of the information on the IEA photovoltaic power generation program); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information on the photovoltaic power system was made, and the FY 2000 results were summarized. In Task I: Exchange of the information on the photovoltaic power system and the spread, the final report on 'the study on added values of PV system' was made. In Task II: Operational performance and design of the photovoltaic power system and subsystem, specifications for new database were determined, and the existing data were checked/revised/added. In Task III: Design and operation of the stand-alone type and remote island use photovoltaic power plant, survey was conducted of the present situation of technical standards and quality guarantee. In Task 7: Photovoltaic power system integrated with construction materials, work was done for making a book of installation samples of the PV system integrated with construction materials in each country. In Task 8: Investigative study of possibilities of the large-scale photovoltaic power generation using the unused land such as desert, a report making of the secondary survey was started. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (Collection of the information on the IEA Solar Heating and Cooling Program); 2000 nendo seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyo reidanbo kyuto program ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

By sending specialists including mostly members of the IEA (International Energy Agency)/SHCP (Solar Heating and Cooling Program) to the Executive Committee Meeting of SHCP and the Task Specialist Meeting, information was collected, and the FY 2000 results were summarized. The mission of this implementing agreement by 2004 was to positively support the creation of the future environmentally sustainable by using solar design/technology to a high degree. For it, the following were to be carried out: development of solar technology including the cost reduction through the joint research with enterprises, construction of the international market, supply of the required information, quantification of the effectiveness of solar technology for the environment, tackling with the international standardization for expansion of the use in the building sector, promotion of solar technology utilization in developing countries, etc. In this fiscal year, finished were Task 19: Solar air/heat collecting system and Task 21: Natural lighting in buildings. Activities of Tasks 22-26, which started in the previous fiscal year, were continued. Activities of Tasks 27, 28 and 29 were newly started in this fiscal year. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Projects for international research exchanges and international seminars; 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo chosa hokokusho. Kokusai kenkyu koryu jigyo / kokusai seminar kaisai jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the results of the international research exchange projects promoted by Research Institute of Innovative Technology for the Earth (RITE) in FY 2000. The international research exchanges are important for creation of new research areas and technological systems for solving the global environmental problems. In order to promote these activities, RITE invites and dispatches researchers to international conferences and symposiums, promotes research exchanges with major foreign research institutes and academic organizations, and invites and dispatches researchers for medium to long periods. These projects promote exchanges of the latest researches with various institutes, both domestic and foreign, and confirm that the research and development projects now RITE is promoting are closely related to those promoted by various organizations. In the FY 2000, RITE invites 5 foreign researchers for joint researches, and invites 3 foreign researchers to international conferences. RITE also dispatches 3 Japanese researchers to American and European universities, and 12 Japanese researchers to international conferences and the like, to effectively promote the domestic researches and grasp development tendencies at institutes of various countries. RITE holds 5 international seminars for exchanging and discussing broad topics over advanced researches related to global environmental technologies by researchers, both domestic and foreign. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

Basic study on intelligent materialization of glass; Glass no intelligent ko zairyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

This is the report No. 98 issued by the Inorganic Material Research Institute. An intelligent material is a substance and/or material which responds intelligently to environmental conditions and exhibits functions. One of the features of amorphous materials including amorphous glass is a large freedom in chemical composition. These materials maintain order in short distance, but have as a whole the turbulent and specific atom orientation. Therefore, high tolerability in selecting the composition, and diverse synthesizing methods are available. A wide range of utilization may be conceived, such as introduction of the state of electrons having different valences in a structure, and the diverse chemical combinations. Patterns of existence of polyhedrons having different orientations, and how they are connected correlate closely with an external environment. Intelligent materials have high freedom against change in the external environment and are suitable to exhibit intelligent functions. Setting heat and light as the external conditions, attempts have been made on search and creation of intelligent materials based on state change induced by interactions between the two factors. Fundamental studies have been made on synthesis of different environment responding glasses and films, and on factors and phenomena for exhibition of the intelligence. 62 refs., 91 figs., 8 tabs.

Study on search of unknown materials. 1; Michi busshitsu no tansaku ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

This is No.92 report of National Institute for Research in Inorganic Materials, concerning search of unknown materials. Purposes of this study are to construct new chemical bond and reaction theory, to systematize the existing compounds, and to search and create the unknown materials, systematically. Structure prediction of electronic state was investigated by means of molecular dynamic method, to determine the electronic state and structure of multi-systems. For the magnetic semiconductors, interactions were investigated between the magnetic spin and electron or hole which is a carrier. The in-solid bond theory aims at clarifying the bond state of materials in which transition metal compounds and inter-electronic interactions are significant. Prediction of the electronic structure of unknown materials can suggest the design of new materials. In the fields of synthesis, design and synthesis of new inorganic ion exchanger and ionic conductor are investigated using Bi oxides and its related materials. There are a lot of compounds having various crystal forms for rare earth element oxides and transition metal oxides. To establish the system of material design, thermodynamics, phase equilibrium diagram, crystal structure, and physical properties of new materials were discussed. 168 refs., 127 figs., 44 tabs.

Development of new supervisory system with ITV. ITV ni yoru kanshi system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimonaga, S; Matsunaga, R; Ono, H [The Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1994-02-28

This paper describes an automatic trespassing supervisory system with ITV and picture processing (PP). The paper details an integrated control system and automatic supervision. The system functions to automatically detect a trespassing by means of PP, transfers items of information collected by sensors to a remote control center, and records relevant data. The operation principle consists of measurement of change in two or more images of moving bodies with binary value at a certain interval, determination on acceptability of the moving bodies represented by human characteristics, and identification of a trespasser. The system consists of an automatic supervisory device using PP and an automatic patrolling and searching device by means of sensor measurements. The supervisory device has images outputted from ITV and VTR processed by PP, host computer, and HD, and linked to an indication mechanism. According to the result of a site test at wireless transmission station of Kyushu Electric Power Company, the difference between measurement values collected by the searching device and those by the supervisory device was [plus minus]3% or less (other than EG output current), which is a useful value for verification. Although the basic technique has been established, practical use of the system still has some problems including performance improvement in picture processing. 37 refs., 38 figs., 18 tabs.

Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

Study on a non-powered heat transporting system; Mudoryoku netsu hanso system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kamiya, Y [Kanto Gakuin University, Yokohama (Japan)

1997-11-25

This paper proposes a non-powered heat transportation (HT) system. The system is composed of an evaporator, condenser, receiver, switching chamber (SC) and 3 check valves which are connected with each other by vapor and liquid tubes. Condensed liquid supercooled in the condenser exists in the receiver forming a saturated condition at a concerned temperature, and condensed liquid is lifted up from the condenser to the receiver by pressure difference between the evaporator and receiver. Generally evaporation pressure is higher by pressure difference between liquid levels in the condenser and receiver. The lifted up amount of condensed liquid increases with evaporation pressure, resulting in an increase in heating surface area of the condenser and amount of condensed liquid. A proper evaporator pressure is thus retained by reduction of evaporation pressure. SC is connected with the receiver and evaporator, and switches high- and low-pressure valves by motion of an inner float to transport heat from the evaporator to condenser. Reverse HT is possible as normal latent HT by installing a bypass. Some problems are also described. 2 refs., 8 figs.

Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

Improvement of performance of the HARBEMAN house; Habiman hausu no seino kaizen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Saito, T. [Tohoku Univ., Sendai (Japan). Dept. of Aeronautics and Space Eng.; Fujino, T. [Mitsubishi Heavy Industires Ltd., Tokyo (Japan)

1998-12-05

A natural energy autonomous house (HARBEMAN house) was built in 1996 in Sendai. This house combinedly utilizes solar thermal, photovoltaic, sky radiation cooling, rainwater energies and so on. In order to utilize a lot kind of natural energies more efficiently, we will improve thermal performance of the solar collector, the sky radiator, and so on. The effect of thermal insulation, tank size, and window glazing on thermal performance will also be examined. This article reports on the improved performance of the HARBEMAN house. (author)

Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1997-07-10

The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

FY 1998 New Sunshine Project. International co-operative project (Summary); 1998 nendo new sunshine keikaku. Kokusai kyoryoku jigyo (sogoban)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the basic plans for the international co-operative projects for development of technologies for commercialization of photovoltaic power systems (e.g., IEA co-operative programme on Photovoltaic Power Systems), and the minutes of the FY 1997 and 1998 meetings of the Solar Energy Technology International Research Co-operative Committee. Japan is responsible for implementing the following projects for promoting international cooperation for, e.g., IEA Photovoltaic Power Systems (PVPS): research and development, demonstration, analysis, information exchange, introduction promotion, etc. for IEA/PVPS Programme; and research and development, demonstration, analysis, information exchange, introduction promotion, etc. for IEA/Solar Heating and Cooling Programme. Japan is also implementing the co-operative projects for the photovoltaic power systems with the Summit participants, based on Science and Technology Working Group established by the Versailles Summit, technology cooperation with, e.g., Australia, and bilateral information exchange and technological survey projects with those countries which have already developed solar energy systems, e.g., USA, France, Spain and Italy. (NEDO)

Trends in business management strategies of major international oil companies; Kokusai sekiyu kigyo meja no keiei senryaku no doko

Energy Technology Data Exchange (ETDEWEB)

Kashio, H. [The Institute of Energy Economics, Tokyo (Japan)

1995-07-01

This paper summarizes the former half part of the analysis made on business strategies of major international oil companies. The net earning of R/D Shell in fiscal 1994 increased by 1.8 billion dollars to 6.3 billion dollars. Its loan rate decreased to 16.7%. It increased the crude oil production by 3% to 2.2 million B/D, and the natural gas production by 1.2% to 7.3 billion cfd. The upstream department had the net earning decreased by 23% to 2.4 billion dollars because of decline in crude oil price. The net earning of the downstream department showed an increase by 20% over that in the previous year to 3.2 billion dollars. The chemical department had its business turned to black ink. The net earning of Exxon in the same year decreased by 200 million dollars to 5.1 billion dollars due to the reduced crude oil price and low refining margin. The upstream and downstream departments showed a decrease of 530 million and 630 million dollars respectively. The chemical department had an increase of 130% to 950 million dollars as a result of the recovery in the European markets. The net earning of Mobile in the same year showed a decrease of 2.1 billion dollars, ending in the amount of 1.1 billion dollars. The decrease has been caused by the decline in crude oil and natural gas prices and a 30% reduction in the refining margin. The chemical department changed for the better, with improved sales margins in oil products sold in overseas markets. 28 figs.

Report on a survey in fiscal 1999. International study exchange project; 1999 nendo kokusai kenkyu koryru jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Exchange with overseas researchers and research organizations has important significance in promoting research and development toward creating new research areas and structuring new technological systems intended for solving global environment problems. In cooperation with RITE and RITE researchers and relevant learned societies, researchers were invited or dispatched to international conferences and international symposiums with regard to global environment related technologies. In addition to interaction with major overseas research institutions and universities, medium and long-term dispatch and invitation have been performed that are considered to play an important role in future research exchange activities based on the achievements of short-term invitations and dispatches and examinations with potential research exchanges. As a result, domestic and overseas interactions on the latest researches were performed, while basic and applied researches related to global environment technologies are being proceeded also in various areas of studies outside the country. It was identified that these exchange activities have close relationship with research and development of industrial technologies serving for global environment preservation, which are being promoted by RITE. (NEDO)

Survey report for fiscal 1999 on internationalization of technologies for effective use of energy resources. Survey of international trend of technology management (Survey of necessity of creating a strategic research organization for researches on technology, management, innovation, etc., for international competitiveness enhancement); 1999 nendo energy shigen yuko riyo gijutsu kenkyu kokusaika chosa kokusai gijutsu keiei doko chosa hokokusho. Kokusai kyoryoku kyoka wo mokuteki to suru 'gijutsu' 'keiei' 'innovation' nado no senryakuteki kenkyu kiko sosetsu no hitsuyosei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Innovation plays an important role for Japan to flexibly utilize its achievements for the purpose of properly responding to new business environments and to secure competitiveness in the market. Japan lacks experts equipped with knowledge and ability as regards technology development and management which are necessary for the planning and creation of technologies, and is also short of institutes for raising experts. In America, technology management won an important position in the 1980s in the effort at industrial renovation, and the industry, government, and academia in a body endeavored to elevate the level steadily, continuously, and deliberately, to eventually provide a source of great propulsion and international competitiveness toward today's economic success. Investigations were conducted, and a proposition is made for the establishment of an international technology management research center. Such a center will study technology management and innovation through international exchange based mainly on the industrial circle and through the organic coordination of the industry, government, and academia for widely observing changes in international society for economic frontier cultivation. A practical training and intelligent network will be organized on the global scale, which will serve as an information transmitter. A skeleton of the plan is shown. (NEDO)

Report on 'manufacturing technology supported by advanced and integrated information system through international cooperation'. Domestic surveys; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kokunai chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The committee of manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC) has been established as the organization to promote necessary surveys, deliberate the research and development guidelines and themes, and thereby support the joint R and D projects with Asian countries to improve information systems for their manufacturing industries by MATIC. The R and D skeletons are set in FY 1994 for the works in and after FY 1995. The relationships between affiliates of Japanese enterprises and local enterprises, actual conditions of the manufacturing industries and so on are surveyed, in order to extract problems related to the information systems for the promising manufacturing industries in the Asian countries. Each industry has its own characteristics with respect to, e.g., numbers f parts and process steps, product life cycle, extent of automation, skill of workers, and spread of the related industries. Therefore, 3 industrial areas are picked up as those considered to be adequate for the case studies, and surveyed for the system functions, performance, elementary techniques and so on which are required to establish the information systems for their production systems. (NEDO)

Report on a survey in fiscal 1999. Survey on the actual state of utilizing unified evaluation models for global warming; 1999 nendo chikyu ondanka ni kansuru togo hyoka model no katsuyo jittai ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present survey is intended to compare and analyze major unified global warming evaluation models available inside and outside the country, and analyze the directionality on supports for the future model developments that will be performed by the Ministry of International Trade and Industry. The report describes in Section 1 how the summaries of the global warming evaluation models may be put into order. A unified evaluation model may be positioned basically as a platform to unify the processes of recognizing scientific problems and the processes of determining the policies. Section 2 describes how the summaries of the major global warming evaluation models may be put into order. The models include the followings: DNE21 (Dynamic New Earth 21), GRAPE model, AIM model, MESSAGE (IIASA) model, IMAGE2 (RIVM), and GREEN (Gene Ral Equilibrium Environment)(OECD). Section 3 summarizes the purposes, general situation of development, scope of the objects, and technological features as the features of each model. Section 4 describes the analysis of the actual state of utilizing unified evaluation models for global warming. The results of the analysis were put into order in a map form to make clear the positioning of the major models that have been put into order. (NEDO)

Fiscal 1999 technical research report. Development project on prompt-effect international standards for developing new industry (Comprehensive survey and research concerning promotion of international standardization); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For encouraging the promotion of international standardization involving the six subjects of advanced technology taken up under the above-named project, wide-range investigations are conducted into measures for international standardization, the activities of international standardizing agencies and organizations, and the approaches of European and American business corporations to this issue. Technical literature and material are studied in Japan, and interviews are held overseas with responsible persons at organizations and corporations engaged in this task. At Standards Development Organization (SDO) of America, verification tests are under way for early development into international standards of technical standards it has so far developed independently. For the strategical utilization of intellectual property incorporated into its technical standards, SDO accepts that the best policy is to win approvals from patent proprietors at the early stage of standardization process by presenting them with conditions about patent implementation. In Europe and America, for the enhancement of their competitive power in the international theater, governments and civil sectors cooperate with each other for the establishment of international standards and, in business corporations, the management takes the initiative in coping with the issue with an understanding that there are business opportunities in international standardization. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Study of the international standardization by the economic evaluation of environmental impacts; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Kankyo compact no keizai hyoka ni yoru kokusai hyojunka no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of the international standardization, conducted was a R and D of `the economic evaluation method of environmental impacts.` Survey/analysis were conducted of the trends in the U.S. and Europe where the study on environmental costs is advancing, and study systems were constructed in cooperation with Resources for the Future (RFF), the U.S. Electric Power Research Institute, the University of London, etc. As to impact analysis models, the development of environmental excrement transfer models has been finished, and the development of D-R relational equations which reflected characteristics in Japan has been started. In the joint study with the U.S. RFF, conducted were survey/analysis using the CVM (contingent valuation method). By the comparison of the survey data with actual medical data and comparison with the economic value conversion method, etc., validity and consistency of the CVM method were verified. As a result, it was found that these survey data could be explained without inconsistency. A case study of the environmental cost evaluation was made for electric power, iron/steel and electricity, and it was verified that this developmental method was fully applicable to the environmental impact evaluation of the actual production system. 27 refs., 33 figs., 89 tabs.

FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

Fiscal 2000 project for promoting international cooperation for global environment. International information network project for global environment (Survey on information network for environmental technology transfer); 2000 nendo chikyu kankyo kokusai kyoryoku jigyo hokokusho. Chikyu kankyo kokusai joho network jigyo (kankyo gijutsu iten joho network chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Environmental technology information database has been shown on Internet for the purpose of transferring environmental technologies; in order to reinforce it this year, a viewpoint was directed to developing countries, with research carried out on the environmental preservation information of the Philippines and Thailand. In the research, in view of promoting cleaner production in developing countries, UNEP regional offices, which are active in the operation, and Asian Development Bank were examined, with their methods, plans and strategies of disseminating the cleaner production surveyed. Also, the database was added with the activities by the organizations concerned in Philippines and Thailand. As for the environmental management system ISO14001, some local governments in Philippines and Thailand will presumably acquire ISO14001 in the future to deal with their environmental management; under the circumstances, Miyama Town was chosen that was first in Mie Prefecture to obtain ISO14001, with the details investigated concerning its environmental policy and the acquisition of ISO14001; and, on the basis of the investigation, a database was prepared so that guidelines for environmental management were provided for the local governments. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (IEA photovoltaic power generation program - Collection of the information on Task IX); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information was made on Task IX: Promotion of the effective spread of the PV technology in developing countries, and the FY 2000 results were summarized. In Task IX, for technical/economic subjects in introducing the PV system to developing countries, a commendable/practical guide using the experiences having been gained was to be arranged. Also, workshop was to be opened in developing countries as model, and cooperation was to be promoted with international organizations such as the Bank of the World. In this fiscal year, two meetings of specialists (abroad) and four sectional meetings of operation (in Japan) were held. This fiscal year was the second year of the 5-year plan. The standard for selecting developing countries as model was studied, and a draft of the commendable/practical guide was made and discussed in the meeting of specialists. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. International cooperation project (IEA photovoltaic power generation program - Collection of the information on Task IX); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai jigyo kyoryoku (IEA taiyoko hatsuden program task IX ni kansuru joho shushu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on 'the Implementing agreement for a research cooperation project on the photovoltaic power system' being promoted by IEA, collection of the information was made on Task IX: Promotion of the effective spread of the PV technology in developing countries, and the FY 2000 results were summarized. In Task IX, for technical/economic subjects in introducing the PV system to developing countries, a commendable/practical guide using the experiences having been gained was to be arranged. Also, workshop was to be opened in developing countries as model, and cooperation was to be promoted with international organizations such as the Bank of the World. In this fiscal year, two meetings of specialists (abroad) and four sectional meetings of operation (in Japan) were held. This fiscal year was the second year of the 5-year plan. The standard for selecting developing countries as model was studied, and a draft of the commendable/practical guide was made and discussed in the meeting of specialists. (NEDO)

Survey on commercial use of fuel cells; Nenryo denchi ni kansuru jitsuyoka no tame no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The basic survey was carried out for the future approach to R & D of fuel cells. Phosphoric acid fuel cell (PAFC) is in the stage of demonstration research and field test supported by subsidy after the end of Sunshine project. Its reliability and durability problems are being solved, and its cost reduction is only one problem for practical use. Distributed systems or on-site systems will be used utilizing its excellent environmental characteristics. Molten carbonate fuel cell (MCFC), solid oxide one (SOFC) and polymer electrolyte one (PEFC) under development were thus surveyed. The following are surveyed: (1) Contribution to a human society such as improvement of energy demand/supply structure and environmental protection, (2) Technological items such as outlook for R & D, validity of developmental issues, comparison between various R & D and significance in industrial promotion, (3) Economic items such as profitability and feasible period, and (4) Social items such as sociability, compatibility to needs, possibility of locations, international meaning, market scale and promotion scenario. 90 refs., 67 figs., 96 tabs.

Investigation into the emission of greenhouse effect gases; Onshitsu koka gas no haishutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper grasped the situation of greenhouse effect gas emissions of advanced countries based on the reports from them. The advanced countries which concluded the U.N. Framework Convention on Climate Change (OECD member countries, the former U.S.S.R., and East European countries) are to be reported to the office concerned with work for the framework the situation of their greenhouse effect gas emissions according to the obligation of the framework. In and after April 1997, they made the second report. The paper summarized changes in emission amount, the future trend, and the policies/measures mainly taken of nine countries which have already presented the second report (the U.S., the U.K., Germany, Holland, Italy, Norway, Sweden, Finland, and New Zealand) and one country (Russia) which has made only the first report. Moreover, the literature was collected and summed up concerning the mechanism and coefficients of the emission of nitrous oxide and methane. The collected literature was classified into all fields/plural number of fields, energy relation, industrial process relation, relation with the use of organic solvent and other products, agricultural relation, relation with changes in land use and forests, and waste relation. 4 figs., 228 tabs.

Survey and research on applications of parallel compiler; Heiretsu compiler tekiyorei ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-31

An urgent proposition is made that an advanced computing software program development and maintenance system be set up, and activities are conducted in search of strategies and guidelines for the establishment of such a system. Out of recognition that it is important to develop software programs such as operation systems for supercomputers, a survey is conducted of software technology development strategies especially involving application software programs. It is proposed that efforts be positively exerted to develop strategic software developing programs for advanced computing for concentratedly enhancing the development now under way of strategic software programs. In concrete terms, named as strategic software programs to be developed are a next-generation semiconductor TCAD (technology computer-aided design) system, protein structure/function analysis system, fatigue simulation system, next-generation fluid analysis system, chemical reaction simulator, grid computing, and a nanodevice surface analysis system. (NEDO)

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

Catalytic activity of pyrite for coal liquefaction reaction; Tennen pyrite no shokubai seino ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Hirano, K.; Kozu, M.; Okada, T.; Kobayashi, M. [Nippon Coal Oil Co. Ltd., Tokyo (Japan)

1996-10-28

Since natural pyrite is easy to obtain and cheap as coal liquefaction catalyst, it is to be used for the 150 t/d scale NEDOL process bituminous coal liquefaction pilot plant. NEDO and NCOL have investigated the improvement of catalytic activity of pulverized natural pyrite for enhancing performance and economy of the NEDOL process. In this study, coal liquefaction tests were conducted using natural pyrite catalyst pulverized by dry-type bowl mill under nitrogen atmosphere. Mechanism of catalytic reaction of the natural pyrite was discussed from relations between properties of the catalyst and liquefaction product. The natural pyrite provided an activity to transfer gaseous hydrogen into the liquefaction product. It was considered that pulverized pyrite promotes the hydrogenation reaction of asphaltene because pulverization increases its contact rate with reactant and the amount of active points on its surface. It was inferred that catalytic activity of pyrite is affected greatly by the chemical state of Fe and S on its surface. 3 refs., 4 figs., 1 tab.

Experimental study on the simple water hammer pump; Kan`igata water hammer pump ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Muto, M; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1997-11-25

Outlined herein are experimental results with a water hammer pump. It is a unique pump in that it depends only on potential energy of water to pump-up water. Water flows downwards from a reservoir at a high position into the pump , and is released from the exhaust valve. When velocity of water flowing in the pipe reaches a certain level, hydraulic force exceeds gravity of the exhaust valve to rapidly closes it, which is accompanied by rapid increase in pressure in the pump. High-pressure water flows into the air chamber, after pushing up the lifting valve, to compress air in the chamber. The lifting valve is closed, when pressure in the air chamber exceeds that in the pump, to pump up water in the chamber through the lifting pipe. Closure of the lifting valve produces a negative pressure within the pump, which, together with gravity of the exhaust valve, opens the valve again. The pump lifts water at 1.64l/min under the conditions of head: 3m and lift: 6m at an efficiency of 48.1%. 1 ref., 4 fig., 2 tab.

Temperature dependency of electrical resistivity of soils; Tsuchi no hiteiko no ondo izonsei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Park, S; Matsui, T [Osaka University, Osaka (Japan). Faculty of Engineering; Park, M; Fujiwara, H [Osaka University, Osaka (Japan)

1997-10-22

Kinds of ground materials, porosity, electrical resistivity of pores, degree of saturation, and content of clays are the factors affecting the electrical resistivity of soils. In addition to these factors, the electrical resistivity of soils around hot spring water and geothermal areas depends on the temperature due to fluctuation of cation mobility in the pore water with the temperature. In this paper, the temperature dependency of electrical resistivity of groundwater and soils is investigated by recognizing that of groundwater as that of pore water. As a result, it was found that the electrical resistivity of groundwater becomes lower as increasing the amount of dissolved cation, and that the temperature dependency of electrical resistivity is not significant because of the small mobility of cation. The electrical resistivity of soils was significantly affected by that of pore water, in which the mobility of cation was changed with temperature changes. Accordingly, the temperature dependency of electrical resistivity of soils has a similar tendency as that of groundwater. 5 refs., 9 figs., 2 tabs.

Consideration of some difficulties in migration velocity analysis; Migration velocity analysis no shomondai ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Akama, K [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1997-10-22

Concerning migration velocity analysis in the seismic exploration method, two typical techniques, out of velocity analysis techniques using residual moveout in the CIP gather, are verified. Deregowski`s method uses pre-stacking deep-level migration records for velocity analysis to obtain velocities free of spatial inconsistency and not dependent on the velocity structure. This method is very like the conventional DMO velocity analysis method and is easy to understand intuitively. In this method, however, error is apt to be aggravated in the process of obtaining the depth-sector velocity from the time-RMS velocity. Al-Yahya`s method formulates the moveout residual in the CIP gather. This assumes horizontal stratification and a small residual velocity, however, and fails to guarantee convergence in the case of a steep structure or a grave model error. In the updating of the velocity model, in addition, it has to maintain required accuracy and, at the same time, incorporate smoothing to ensure not to deteriorate high convergence. 2 refs., 5 figs.

Survey of energy load leveling system in Europe; Energy fuka heijunka taisaku ni kansuru Europe chosa

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Y. [Setsunan University, Osaka (Japan). Faculty of Engineering

1998-05-05

This paper describes the survey of energy load leveling systems in Europe. In Denmark, especially regional heating is remarkably diffused, and they have 350 plants. With extending the service areas, the energy load leveling has been promoted. For the cogeneration plants of SK Power, the largest electric power company, they have hot water heat storage tanks for regional heat supply with a total capacity 2,200 MWh. The regional heating system in Goeteborg City of Sweden supplies 80% of the total heat demand of the city. Unused energy sources derived from petroleum refining, sewage treatment, and garbage burning are utilized. In Uppsala, they have seasonal heat storage systems using solar heat. The Vienna Regional Heat Supply Corporation supplies heat equivalent to 5,000 GWh a year. Cogeneration plants and garbage burning plants are used as heat sources, and 25% of the total heating in the city is supplied. In Austria, they have an electric power demand with a peak in winter, and they have a pumped-storage power station in Kaprun for the annual load leveling using dump power in summer. This paper also introduces a compressed air storage gas turbine plant at Huntorf of Germany, and a large-scale underground natural gas storage of Gaz de France. 6 figs.

Test and evaluation on safety relating to biotechnology; Biotechnology ni kansuru anzensei no shiken to hyoka

Energy Technology Data Exchange (ETDEWEB)

Okada, M. [Bio-Oriented Technology Research Advancement Inst., Saitama (Japan)

1996-09-05

This paper describes the current status and how works are being carried out on safety tests and evaluation of gene recombinants in plants and microorganisms. In the field of plants, Flavr Savr tomato which has been improved in fully ripe fruit distribution and keeping quality was commercialized as the world`s first recombinant food in May 1994 by Calgene, Inc. of America. Other vegetables, such as soybean, corn, potato, and pumpkin have been completed of all items of safety evaluation, and are approaching the commercialization phase. The safety evaluation system for living organisms created by using recombinant DNA technologies has been established internationally with regard to its general framework and contents based on accumulated knowledeges and experiences as a result of utilization of over twenty years. Industrial utilization guidelines for recombinants in Japan have been established in correspondence with the OECD recommendation in 1986. Experiments to verify recombinants to be safe in environment, and cultivation of the recombinants for utilization are performed based on the experimental guidelines and utilization guidelines. 15 refs., 1 fig., 5 tabs.

Research for a database of alternative energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper collects and arranges data on the unused energy in terms of examples of the introduction in Japan and other countries, policies, laws and rules, subsidy systems, etc. In the overview of the system, described was typical heat supply systems utilizing unused energy. As to concrete examples of the introduction in Japan, the examples were arranged by unused energy source, by temperature level, and by region, and a detailed data book of the typical introduction examples was made. As to examples overseas, data were arranged on the introduction mainly in Europe and the U.S. With relation to policies, laws and rules, and subsidy systems in Japan and overseas, investigated were policies, laws and rules, and subsidy systems concerning unused energy mostly in Japan, Europe and the U.S. As to the production quantity, the actual amount of introduction, and the predicted amount of introduction, survey on the effect and arrangement of the data were conducted in terms of typical two heat supply facilities utilizing unused energy. The paper adds information pertaining to the cost, main related companies and groups, the distribution cost, etc.

Experimental study on the control interaction force coefficient; Soju ryutairyoku kansho keisu ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatake, K; Oda, K; Yoshitake, A; Fujita, K; Nakajima, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1996-04-10

The interaction force induced to hull by steering is important for prediction of control performance of ships. The control interaction force coefficient dependent on the steering has been investigated through the rudder angle tests using three small model ships with a length of 2.5 m, i.e., mathematical type of ship, cargo type of ship, and tanker type of ship. The interaction forces acting on the hull, propeller, and rudder were determined by measuring the lateral force as well as the forward force of the hydrodynamic forces acting on the rudder. These forces were compared with the theoretically calculated values. Prior to the rudder angle tests, the self propulsion factor and the number of revolution of propeller were determined from the results of the open water tests, resistance tests, and self propulsion tests by the changing load method. The rudder angle tests were conducted under this number of revolution of propeller as a standard condition, and under those increasing and decreasing by 15%. Consequently, the interaction forces determined from the rudder angle tests agreed well with those determined from the other tests. When comparing the control hydrodynamic forces determined from the tests with those theoretically calculated, a similar trend was observed. Effectiveness of the theoretical model was confirmed. 4 refs., 14 figs., 3 tabs.

Emergency housing after natural disaster; Shizen saigaigo no oukyu kyoju kankyo seibi sisutemu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Masami [Kyoto University, Kyoto (Japan). Graduate School of Engineering

1998-12-16

In Japan, there were some serious disasters in recent years. In 1991, Unzen-Fugendake erupted and more than 1,000 people were forced to take refuge from their houses. In 1993, Hokkaido-Nanseioki earthquake attacked the south-east area of Hokkaido and more than 3,557 houses were destroyed. In Japan, the government supplies the temporary housing to those who lost house from the natural disasters. The purpose of supplying temporary houses mentioned in the disaster relief law (established in 1947) prescribes the purpose of temporary housing that to rescue the poor who can not afford getting a shelter with their own funds. But actual condition of temporary housing is completely different. Government supplies temporary housing to all those who request temporary housing. The term of using temporary house tend to become longer. The regulation about temporary housing has not been yet up to dated. Many problems concerning about temporary housing originate in outdated regulation. The temporary housing have to be ranked in the part of restoration process from natural disaster. (author)

Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

Static behaviors of long-span cable-stayed bridge; Chodai shachokyo no seiteki kyodo ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Xie, Xu [Saitama Univ., Saitama (Japan). Graduate School; Yamaguchi, H.; Ito, M. [Saitama Univ., Urawa (Japan). Faculty of Engineering

1996-04-21

In this study, incremental equation of cable-stayed bridge is formulated by finite element method taking the geometrical nonlinear analysis into account. Then, as an example of designing a bridge with 1500m span, setting up the initial tension, analysis of in-plane behavior caused by live loads as well as analysis of the behavior against wind caused by out-of-plane wind load that are necessary for designing a bridge with 1500m span are carried out. The main results obtained through the study are as follows. As for the cable stayed bridge with 1500m center super long-span having supplementary supporting points between the side arms, the geometrical non-linearity caused by the in-plane design live loads is not remarkable. The effects of wind which acts on girders on analysis of the behaviors against wind are different depending on the aerodynamic performance of the girder and in the case of high wind speed, strong effects on the behavior against wind of the in-plane and screws generate. As the changing of tension of the cable makes influences on the force of in-plane cross section and on displacement of the girder, if the wind speed is very high, the analysis results of the behaviors against wind of in-plane and screws of the cable-stayed bridge may be different depending on in what manner the wind load on the cable to be treated. 16 refs., 16 figs., 1 tab.

CFD prediction of heat island formation on growing Asian cities. Effect of urbanization in Shanghai; Kyodaikasuru Asia no toshi ni okeru heat island keisei ni kansuru CFD yosoku. Shanghai no toshika ga oyobosu eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ojima, T.; Murakami, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Mitsumoto, K. [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-10-01

Study is conducted of the effect of change in land use and increase in artificial exhaust heat on heat island formation in Shanghai. Concerning the land use distribution in Shanghai, a point sampling survey was conducted in the 1930s using topographic charts, when the area was broken down into building-occupied region, paddy field, bare ground, and waters. In the 1990s, thanks to data from satellites, high-density and low-density urban regions have added. Calculation for Shanghai is performed, based on the rate of increase in Tokyo`s population and data predicted for Shanghai`s population, on the assumption that Shanghai`s population in the 2050s will grow 2.3 times larger than it is in the 1990s. The prediction thus produced indicates that the urban area in Shanghai in the 2050s will be as large as that of the present-day Tokyo that covers a 50km zone. Heat island formation prediction for Shanghai is worked out using computational fluid dynamics (CFD)-aided simulation. According to the prediction, while the maximum temperature in the 1930s was 29.6degC or 4degC higher than in the suburbs, it is 33.2degC or 7.6deg higher in the 1990s, and will be 34.4degC or 8.6degC higher in the 2050s. 16 refs., 11 figs., 1 tab.

Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

Fiscal 1997 survey report. Subtask 2 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study for the promotion of international cooperation); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 (kokusai kyoryoku suishin no tame no choa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The survey was aimed at developing the WE-NET as a joint project worldwide by taking concrete measures such PR activities to obtain international understanding and cooperation of WE-NET based on the survey/grasp of researches of research institutes in each country and the developmental trend of hydrogen energy in each of the main countries. Implementing a `long-term vision for the WE-NET international cooperation,` the following measures were taken in fiscal 1997. PR activities were positively developed which coped with the worldwide increasing interest in WE-NET such as delivery to overseas institutions of the fiscal 1996 survey report in English summarized by NEDO and information exchanges, and participation in international conferences and presentation of the research results. From a standpoint of positively proceeding with the international technical information exchange, the following were conducted following fiscal 1996: 1) the evaluation study jointly made with Stanford University of effects of reducing air pollution by introducing hydrogen cars, 2) survey on the U.S. hydrogen project, and 3) preparation for opening of the WE-NET internet home pages. 17 figs., 18 tabs.

FY 1999 survey report on the global environment international cooperation promotion project/global environment international information network project. Survey of the environmental technology transfer information network; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / chikyu kankyo kokusai joho network jigyo. Kankyo gijutsu inten joho network chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

At International Center for Environmental Technology Transfer, the following were conducted for enrichment of the environmental technology information: surveys of the state of activities in international organizations and developed countries, cleaner production (CP), ISO, etc. and construction of database. As to the reinforcement of environmental preservation technology information database, enrichment of the data on environmental preservation was attempted mainly about ways of thinking of environmental preservation which brought fruitful results to international organizations overseas. The hierarchization/supplementation were conducted of CP databases which attract much attention especially among developing countries. In the survey of models for environmental preservation, autonomous bodies in Mie prefecture and the certified consultant were taken up to study the process up to the acquisition of ISO14001. The database was so made that it can be a guide for the environmental management in autonomous bodies in developing countries. In the CP survey, as to the United Nations Environment Programme (UNEP), definition/thought were examined in terms of CP, eco-efficiency, pollution prevention, green productivity, etc. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Quantification of the sensory evaluation and international standardization in the paint field; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Toryo bun`ya ni okeru kanno hyoka no teiryoka to kokusai hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Japanese paint users demand products of higher-quality than users in the U.S. and Europe, and therefore, paint makeres in Japan are making strenuous efforts to improve the product quality in terms of homogeneity, appearence and durability of the surface of paint films. However, the evaluation of paint surfaces is conducted by the qualitative sensory evaluation, resulting in obtaining no appropriate evaluation. Accordingly, the following were developed as new evaluation methods which give rational and economical indicators, contribute to shortening of the period for development of new products, and aim at the international standardization: 1) quantitative evaluation of the paint drying process; 2) image analysis of the degraded part of paint films; 3) surface analysis of paint films. In 1), a kinetic friction measuring quantitative evaluation of the surface of paint films was developed. In 2), the development of an exclusive program by the image analysis made the quantitative evaluation with high accuracy/reliability possible. In 3), an evaluation method was developed in which differences among the specimens can be detected by the chemiluminescent measurement in an extremely early stage of exposure when the gloss change just begins. As to the chalking, a new evaluation was developed in which the degree of chalking can quantitatively be evaluated by attaching a special adhesion tape to the degraded part of paint films and by the optical measurement of the degree of transparency. 101 refs., 341 figs., 118 tabs.

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

Investigation on structuring the human body function database; Shintai kino database no kochiku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Based on the concept of human life engineering database, a study was made to know how to technically make such a database fittable to the old people in the age-advancing society. It was then proposed that the old people`s human life engineering database should be prepared to serve for the development and design of life technology to be applied into the age-advancing society. An executive method of structuring the database was established through the `bathing` and `going out` selected as an action to be casestudied in the daily life of old people. As a result of the study, the proposal was made that the old people`s human body function database should be prepared as a R and D base for the life technology in the aged society. Based on the above proposal, a master plan was mapped out to structure this database with the concrete method studied for putting it into action. At the first investigation stage of the above study, documentation was made through utilizing the existing documentary database. Enterprises were also interviewed for the investigation. Pertaining to the function of old people, about 500 documents were extracted with many vague points not clarified yet. The investigation will restart in the next fiscal year. 4 refs., 38 figs., 30 tabs.

Numerical simulation on streaming potentials in a wellbore; Koseinai no ryudo den`i ni kansuru suchi simulation

Energy Technology Data Exchange (ETDEWEB)

Ikeda, N [Kyushu University, Fukuoka (Japan)

1996-05-01

This paper reports numerical computation of streaming potentials which are generated by transient pressure waves propagating the vicinity of wellbore wall immediately after a mud cake formed on the wellbore wall has been removed. One existing analysis solution on heat conduction was utilized upon changing the parameters in order to derive fluid pressure inside the ground bed. Calculations were carried out by using the existing three-dimensional finite difference method (partly re-written) based on the relationship constituted between the fluid pressure and the streaming potential. This paper presents results of calculating the streaming potentials in wellbores on models having wellbores filled with mud water in a cubic ground bed existing with ground bed water at saturation of 100%. The calculations have been conducted on the following cases: a case where permeability of the ground bed is small with the fluid under two conditions of low electric resistivity and high electric resistivity, a case where the permeability is large with the fluid under the above conditions, and a case where a small area of bore wall is covered with a rubber pad having high electric resistivity under a low electric resistivity condition. 8 refs., 5 figs.

Study on fuel particle motion of a diesel spray; Diesel funmu ryushi no kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, N. [Isuzu Motors Ltd., Tokyo (Japan); Tsujimura, K.

1998-08-25

This study was performed to clarify the mechanism of mixture formation at peripheral area of diesel spray with PIV technique. Two dimensional cross-sectional photographs of diesel spray were taken with double pulse laser sheet. Local fuel spray particles were analyzed with an auto-correlation method and velocity vector and vorticity of the fuel spray particle were obtained. The vortex number increased and vorticity scale became smaller and its value grew higher with both smaller injection nozzle diameter and higher fuel injection velocity. With this injection condition, the mixing of fuel spray with ambient gas seems to be improved and the turbulence is expected to increase in the regions of higher vortex number, higher vorticity and smaller vorticity scale. Based on above results, the branch-like structure of diesel fuel spray was considered to be caused by vortices which formed in the shear layer between the spray and the ambient gas. 14 refs., 18 figs., 1 tab.

Indoor environment and allergy except housedust mite; Jukankyo to allergy ni kansuru dani igai no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakao, F.; Nishima, S.

1998-05-31

Pathopoiesis factors of allergic diseases include immune antibody productivity sthenia reacting with antigens such as mite or the like in allergy reaction which is regarded as based on genetic fact (atopic diathesis), and environmental factors as external factors. The environmental factors are further classified into specific factors (antigens) and nonspecific factors. The former factors include the indoor factors such as mite, mould, animals bred indoor, etc., and outdoor factors such as pollen and so on. The latter factors include indoor factors such as passive smoking, carbon monoxide, nitrogen oxides, formaldehyde, etc., and outdoor factors such as sulfur oxides, nitrogen oxides, airborne particles and so on. In this paper, the environmental factors in relation to allergic diseases expect mite are introduced. Besides mould, cockroach/insect, fur dust and dandruff of animals, adjustment of room temperature/humidity, smoking, indoor and outdoor air pollution are mentioned as the environmental factors expect mite, and the cause-effect relations thereof are explained. 24 refs., 3 figs., 7 tabs.

Study on the thermal stability of nitrobenzene derivatives; Chikan nitorobenzen rui no netsu anteisei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, Tatsuya; Akutsu, Yoshiaki; Arai, Mitsuru; Tamura, Masamitsu [The University of Tokyo, Tokyo (Japan). Department of Chemical System Engineering School of Engineering

1999-10-31

In order to clarify the thermal decomposition behavior of nitrobenzene derivatives, the influences of interaction between nitro group and other substituents on thermal decomposition of nitrobenzene derivatives have been studied using sealed cell DSC and PM3 MO calculations. As a result, the mixtures of nitrobenzene and mono substituted benzenes having substituents containing hydrogen such as {sup -}CH{sub 3}, {sup -}COOH, {sup -}NH{sub 2}, and {sup -}OH showed 30-100 degree C lower T{sub DSC} value than nitrobenzene. Mono-substituted nitrobenzene having substituents containing hydrogen also showed lower T{sub DSC} value. On the other hand, PM3 MO calculations of hydrogen-bonded complexes of nitrobenzene and mono substituted benzene show that the hydrogen bonding of a nitro group and hydrogen of substituents may make the N-O bond length longer to induce the thermal decomposition. From These results, it can be said that the thermal decomposition of nitrobenzene derivatives would be unstabilized by the hydrogen bonding of a nitro group and a substituent containing hydrogen. (author)

Feasibility study for seismic monitoring of gas injection; Atsunyu gasu monitaringu no kanosei hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishida, A.; Ogawa, T.; Yokota, T.; Shimada, N.; Onozuka, S.; Kono, F.; Miyagi, T. [Japan National Oil Corp., Tokyo (Japan)

1998-10-30

In this study, seismic monitoring of injected gas in a carbonate reservoir was investigated using multidisciplinary approach which consisted of geological/reservoir modeling, reservoir flow simulation, rock physics and seismic modeling. A case study was conducted over Lower Cretaceous carbonate reservoir offshore Abu Dhabi. The gas saturation and reservoir pressure data were obtained from the reservoir flow simulation. The velocity data of dry rock samples under the various conditions were also obtained from rock physics study. These outputs were converted to the velocity model using Gassmann's equation. The calculated velocity from Gassmann's equation is well correlated with velocity from laboratory measurements. Therefore we con confirm that the Gassmann's equation is applicable to estimate the velocity of the gas saturated reservoir rock. Based on the velocity model, synthetic seismic sections before and after gas injection were constructed in order to verify the influence of gas flood. As the results, amplitude difference between the two synthetic seismograms was observed at top and bottom reflectors of the reservoir zone. This amplitude variation is caused by both gas saturation change and pressure change. Although further investigation is needed to detect the cause of the variation, this study indicates the possibility of seismic reservoir monitoring. (author)

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-10

Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

Study on the product estimation of small wind turbines; Kogata fusha no hatsudenryo yosoku ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsuzawa, K.; Kimura, Y.; Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan); Nagai, H. [Nihon Univ., Chiba (Japan). Coll. of Industrial Technology

1998-09-01

In order to clarify problems involved in application of Weibull probability distribution used for estimation of power production by a large wind turbine to a small wind turbine, and solutions thereof, the estimated results are compared with the observed ones. The conventional estimation method, when applied to a small wind turbine, tends to overestimate production of power, because of overestimated production in a high wind velocity range which occurs less frequently. Estimation of power produced by a wind turbine is based on working wind velocity range, determined from the furling mechanism for the power generation characteristics of the wind turbine concerned. In the case of a small wind turbine, on the other hand, better estimates are obtained from the working wind velocity range in which Weibull wind velocity distribution is used to determine probability of occurrence. For wind turbines working at low to medium wind velocities, such as Savonius wind turbine, the estimates are in fairly good agreement with the observed results, by which is meant that the conventional estimation method aided by Weibull distribution can be directly applicable to small wind turbines. 4 refs., 3 figs., 3 tabs.

Study on the structural characteristics of extradosed concrete bridges; Ekusutoradozudo kyo no kozo tokusei ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Oka, Y. [Japan Highway Public Corp., Tokyo (Japan); Kasuga, A. [Sumitomo Construction Co. Ltd., Tokyo (Japan); Yamazaki, J. [Nihon Univ., Tokyo (Japan). Coll. of Science and Engineering

1997-03-31

Parameters are analyzed to provide data for deciding, in the planning and designing stages, whether a cable stayed bridge or an extradosed bridge should be adopted. Comparative investigation of the vibration properties of both types of bridges is also referred to. The result of the study on the structural properties of the cable stayed road bridge and the extradosed road bridge is introduced. Based on the concept of the extradosed bridge, designers are now able to select without restraint the after load sharing rate of the diagonal members. Parameter analysis of a diagonal member reinforced 3-span continuous beam is performed. By introducing indices showing the load sharing rate of the diagonal member, the cable stayed bridge can be distinguished logically from the extradosed bridge in designing. It is found important that the height of the main tower is set to approximately 10% the length of the center span for the construction of the extradosed bridge. The vibration properties of the cable stayed bridge and the extradosed bridge of the same scale are compared. 7 refs., 18 figs., 6 tabs.

Report on International Symposium for the Promotion of APEC Environmental Technology Exchange and Experts; APEC kankyogijutsu koryusokushin kokusai shinpojium jisshi hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The above event took place at Nagoya City, Japan, on December 5, 2000. Taken up were the response of developing nations to the problem of environmental protection, their needs for environmental technologies, examples of the transfer of environmental technologies carried out by Japan's environment related businesses or organizations, introduction of technologies Japan was able to present, and so forth. Introduced also were the current state and future outlook of such activities as the exchange of environmental technologies and business through the utilization of the virtual center for APEC (Asia-Pacific Economic Cooperation Conference) environmental technology exchange now in service, and so forth. At the symposium, a keynote address entitled Toward the Realization of Sustainable Society was delivered by Professor Yamamoto of the Institute of Industrial Science of the University of Tokyo. Panel discussions were held on the exchange of environmental technologies and business making use of the international network APEC-VC (virtual center) at Session 1, on some front-line cases of environmental technology transfer at Session 2, and on the transfer of technologies useful for developing nations as it ought to be at Session 3. (NEDO)

Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports presented to the international forum held by RITE); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishihn jigyo kokusai seminar shiryo. RITE chikyu kankyo kokusai forum hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research Institute of Innovative Technology for the Earth (RITE) has been inviting creative, advanced research projects still in the early stage on an international scale to raise the research seeds for global environment preservation, and promoting the selected themes. The organization has invited the domestic authorities and researchers for the research projects selected from abroad as the good projects in the areas of biology and chemistry, to hold the international forum in March 2001. The keynote lecture in the area of biology addresses the latest researches on plant and life science, stressing how the researches contribute to global environmental problems. The keynote lecture in the area of chemistry addresses possibility of establishment of energy resource cycles utilizing the natural force of the earth. The last lecture introduces the research results by the environmental catalyst research group of RITE. The forum has animated questions and answers in the lectures selected as the good research projects. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.4). Achievement report on effective utilization of waste heat energy; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.4). Hainetsu energy no yuko riyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Endeavors are exerted to develop a medium temperature thermoelectric module technology, which is one of energy/environment related technologies, in cooperation with Russia. The ultimate goal of this technology is to develop a hybrid power generation system which utilizes waste heat. Activities are conducted in three fields involving (1) the basic concept and design of thermoelectric power generation systems, (2) development of thermoelectric power generation systems, and (3) others, including the goal and self-evaluation. Summarized in field (2) are the overall activity plan, development of medium temperature thermoelectric power generation modules, development of cascade type hybrid modules, development of thermoelectric power generation systems, results of thermoelectric power generation system evaluation tests, and technical problems. Carried out for the development of thermoelectric power generation systems are the development of a medium temperature p-type thermoelectric power generation material Mn-Si, development of a method for synthesizing the Mn-Si material, and the development of a medium temperature n-type thermoelectric power generation material Co-Sb. Various methods are studied relative to the fabrication of electrodes, and the thermal spraying method is employed for a success in the development of a medium temperature thermoelectric power generation module of Mn-Si(p)/Co-Sb(n) for the first time in the world. (NEDO)

Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-11-01

On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-10

This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-11-01

On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on chemical use); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-04-15

The whole amount of hydrogen consumption for chemical industries all over the world is estimated to be 249.7 billion Nm{sup 3} in 1974, while 367.2 billion Nm{sup 3} in 1980 roughly under a bold assumption, based on 3 current big consumption fields of ammonia production, methanol production and petroleum refining, and some promising fields in the future such as reduced iron and synthetic protein. Consumption ratios for every field are probably 54.9% in ammonia production, 30% in petroleum refining, 9.5% in methanol production and 5.6% in others in 1974, and nearly similar in 1980. However, although there are various troubles, if a large amount of methanol is used as fuel in the future, and its production plan is promoted to satisfy the demand of methanol fuel, hydrogen consumption for methanol production will increase drastically. In the future, if the production process of hydrogen as secondary fuel is established, such hydrogen also will be used for various chemical industries naturally. Research was thus made on use of oxygen as byproduct inevitably. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-10

This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

Survey report for fiscal 1999 on internationalization of technologies for effective use of energy resources. Survey by exploration of international cooperative researches on energy-saving through advanced use of steel slag; 1999 nendo energy shigen yuko riyo gijutsu kenkyu kokusaika chosa hokokusho. Tekko slag no kodo riyo ni yoru sho energy gijutsu ni kansuru kokusai kyodo kenkyu no tansaku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As for the collection of sensible heat, 1/3 of blast-furnace slag is treated to the purpose at the Teesside Technology Centre, Britain, but none is collected in the latter half of tapping in case there is so much slag that cooling cannot be done in time. In the case of a large blast furnace, some measures have to be contrived because molten iron comes out of the furnace intermittently. In Germany, the heat collection rate is as low as 3%, with no effort made at heat collection. In North America, desire to develop such a technology is not strong. A visit was made to the Institute of Ocean Sciences, Canada, in relation to the concept of using steel slag as a eutrophic source for marine photo-plankton. A large-scale long-term test is under way for examining the relationship between global warming and ocean current circulation. There are possibilities that Japan will enter into the project for a joint study, for example, of heavy metal elution from slag though the test fails to name slag as the direct object of study. Not only for Canada but also for any other country who faces the sea, it may be a meaningful national policy to inject some active ingredients into the sea for an increase in living marine resources. Greece is engaged in the ocean dumping of nickel slag on an experimental basis but, in view of the purpose of the experiment, Japan will not be a participant in the project. (NEDO)

Fiscal 2000 report. Feasibility study on international cooperation concerning technology transfer; 2000 nendo gijutsu iten ni kakawaru kokusai kyoryoku kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A workshop was held concerning technology transfer in the software of environmental technologies, for the purpose of contributing to CTI (Climate Technology Initiative), an international framework for dealing with technological problems in preventing climate change, with the results of the workshop compiled. The workshop was held for a period from September 10 to September 23, 2000; the contents were, for example, an outline on energy conservation, introduction to cleaner production, lectures on related technologies, seminars on actual cases including case studies, factory tours, etc., and discussion session by all participants; and, in general, the workshop was conducted so as to promote understanding on cleaner production and energy conservation. Four lecturers were invited to this workshop from an international organization, U.S. and Japan. In addition, two staff members and two technical consultants from ICETT (the International Center for Environmental Technology Transfer) gave lectures and advice as technology advisers. Three environmental specialists were invited from each of the five countries, China, Indonesia, Thailand, Philippines, and Vietnam. (NEDO)

Survey on the possibility of international cooperation on production technology of biohydrogen; Bio suiso seizo gijutsu ni kakawaru kokusai kyoryoku kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D on the production technology of hydrogen by biotechnology is one of the effective projects for worldwide energy supply technology and global environment protection technology in the 21st century. The research trend of various institutions promoting R and D on production technology of biohydrogen in the U.S.A. and other countries was surveyed together with the possibility of international cooperation. The production technology of biohydrogen is being watched over the world. Various researches are in promotion corresponding to environmental conditions as follows: search of not only photosynthetic bacteria but also such bacteria with hydrogen productivity as algae and anaerobic bacteria, and the gene engineering study for improving the hydrogen productivity of target microorganisms. All the institutions visited for this survey have great expectations in wide cooperative study in the future. On the possibility of international cooperation on the production technology of biohydrogen, the further precise survey should be promoted for developing more effective technologies based on the previous survey results. 156 refs., 10 tabs.

Fiscal 1999 report on international joint research project on global environmental technology; 1999 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of the above-named effort, Japanese researchers were dispatched to overseas universities and laboratories for implementing joint researches into 11 subjects selected by the NEDO (New Energy and Industrial Technology Development Organization) screening committee. When the feedback of fruits of the researches to NEDO projects is taken into account, it may be said that the accomplishments, attained relative to the development of processes for the practical application of environmentally-friendly biomass energy and measures for promoting its adoption, will contribute to the completion of an environmentally-friendly energy production process, excellent in CO2 emissions reduction, in which biomass will be the raw material. In relation to the technology of installing pipes for CO2 discharge into the ocean, some of the dispatched researchers had an opportunity of studying technological problems not deal with under NEDO research and development projects. In the study of organized structures of low-purity CO2 bubble groups, a great contribution was made to the promotion of the NEDO-implemented project of evaluating the impact of CO2 storage in the ocean upon environments. The development of remedial technologies for Microcystis aeruginosa-invaded lakes by introducing environmental engineering assumes a very important position in the endeavors for environmental improvement in developing nations in the Asia-Pacific region. (NEDO)

Fiscal 1998 report on international joint research project for preventing global warming; 1998 nendo chikyu ondanka boshi kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

Japanese researchers were dispatched to research institutes abroad for conducting joint studies on nine subjects for which such efforts would work effectively. The researchers were sent to various research institutes in the U.S., Britain, Germany, and others. The nine subjects were (1) the application of the most up-to-date welding and bonding technologies to liquid hydrogen storage/transportation containers, (2) development of low-temperature high-activity metal catalysts for energy conservation processes, (3) study of CO2 emission behavior using a large-scale simulator of deep sea circumstances, (4) study of condensation control for steam and chemical species in the global atmosphere, (5) numerical analysis of semiconductor crystal growth for ultralow loss power device, (6) development of sulfur-rich hydrocarbon gasification technology using a metal melting furnace, (7) assessment of techniques for evaluating origins of environmental pollution gas, geothermal gas, and soil gas using multiple isotopes, (8) analysis of behavior of the steam circulation type turbine system, and (9) the embodiment of a large premixed compression ignition engine. (NEDO)

Study on abrasion resisting material for apron of dam; Dam apron bu no taimamo sozai ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Inaba, H.; Hiraki, M.; Miyamoto, T. [Hokuriku Electric Power Co. Inc., Toyama (Japan)

1995-01-25

A `laminated rubber tile` and a `shock absorbing holed-in anchor` were devised in connection with the apron of a dam for a hydroelectric power plant. As the result of a survey on the hydroelectric power plants, ten plus places were observed where a general kind of concrete was severely worn in the company territory; but, there were substantial number of rubber materials that had still been sound for over ten years after the installation. In spite of the soundness of the rubber tiles, however, it was observed that their anchor supports had been cut and separated. An abrasion comparison test of concrete and rubber materials revealed that the rubber materials were considerably superior in abrasion resistance. Various rubber tiles were tested for abrasion resistance, tear strength, tensile strength, impact strength, etc.; and methods for fixing rubber tiles were also tested such as a holed-in anchor, chemical anchor and adhesives. As a result, a laminated rubber tile was designed with its upper layer constituted of a rubber sold on the market and its lower layer of a fiber reinforced rubber also on the market, and so was a shock absorbing type holed-in anchor. 1 ref., 11 figs., 4 tabs.

Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

Basic research on the carbon dioxide fixation using seaweed. Kaisorui no tansan gas kotei ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, M.; Ishihara, T. (The Kansai Electric Power Co. Inc., Osaka (Japan))

1993-08-25

Study was made for grasping the basic data of CO2 fixation technology by seaweed. The photosynthesis under the sea, which is different from that on the land, is judged to be made by taking in HCO3[sup -] and converting it into CO2 inside the plant. Porphyra yezoensis which is seaweed is cultivated as comestible. With a rise in CO2 content, the growth in length of leaves was observed to be accelerated through ventilating Porphyra yezoensis with the three test types of air which respectively contained 350ppm (atmospheric CO2 content), 1000ppm and 1600ppm CO2. As a result of measuring the photosynthesis speed by the generated quantity of O2, it was heightened with a rise in dissolved inorganic carbonic acid content of the sea water. Measurement was also made of daily fluctuation in calcification speed by Corallina officinalis capable of calcification by ventilating it with 350ppm and 1600ppm CO2. In case of 1600ppm, the sedimentation of CaCO3 was prevented. In case of 350ppm, the sedimentation was quantitatively larger during the bright period than that during the dark period. The growth of Gracilaria gigas which is an agar material was compared by changing the above CO2 levels. In case of 1600ppm, the weight grew to 2.3 times in 20 days. 16 figs., 2 tabs.

Experimental study of water permeability in waste disposal facilities; Haikibutsu shori shisetsu no shisuisei ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Konishi, M; Shiraishi, H; Terada, M [Okumura Corp., Osaka (Japan)

1995-08-22

A cement-based filler is one of the back filling materials used in radioactive wastes disposal facilities. This paper describes fundamental tests performed on a filling material as to its filling performance, water permeation characteristics, and adsorption property to cerium by using the normal cement mortar (SM) that uses the water-to-cement ratio of 40% and the silica fume mortar (SFM). Furthermore, model wastes were fabricated by using a filling mortar of about 1 m{sup 3} and a 200-liter drum, which were used for tests on the filling and water cut-off performances. The result of the fundamental tests revealed the following matters: all of the materials show good filling performance and adsorbability when an adequate amount of high-performance water reducing agent is mixed; and the diffusion coefficient of the SFM is less than one tenth of that for the SM, showing high water cut-off effect. It was made clear from the tests using simulated test pieces that the Lugeon test value and water permeation coefficient of the SFM is less than half of that for the SM, and high water cut-off effect can be obtained by using the SFM. 11 refs., 8 figs., 4 tabs.

Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

Experimental study on power augmentation of Savonius rotor; Savonius gata fusha no shutsuryoku zokyo ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, S; Kikuchi, K; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1997-11-25

Wind power now being used is mostly for power generation, and the power generating rotor is represented by the horizontal propeller type. The vertical type, such as Savonius rotor which uses drag force, may be used for special purposes. The Savonius rotor has been used for water pumping-up and ventilation for its characteristics of low rotational speed and high torque. The authors have proposed, based on the data collected by operating a wind mill of 10W, a method for reducing resistance by deflecting wind flowing onto the return bucket to augment drag force, in an attempt to make the system more functional. The Savonius rotor is equipped with a semi-cylindrical cover, and guide and side plates, to follow their effects. It is found that these plates work to augment power without needing expansion of sweeping area. 4 refs., 12 figs.

Research on brake noise. Concerning LT drum brake; Brake noise ni kansuru kenkyu. LT Drum brake ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Chikamori, S; Shimizu, Y [Seikei University, Tokyo (Japan); Yano, M [Mitsubishi Motor Corp., Tokyo (Japan)

1997-10-01

The four degrees of freedom of shoe motion were adopted by considering the bending for the shoe vibration, and the simulation model was derived. Using this model, the mechanism by which the squeal is generated was reviewed. And conditions for the occurrence of squeal vibration were determined by a series of simulations. Then father analysis was conducted on the influences of various parameters upon the occurrence of squeal vibration. 2 refs., 10 figs.

Some considerations about improvement for fatigue strength of structures; Shatai kozobutsu no hiro kyodo kojo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kimoto, H; Toyama, K; Maruyama, H; Magara, S [Press Kogyo Co. Ltd., Kanagawa (Japan)

1997-10-01

To reduce weight, higher tensile strength and/or thinner plate are used or considered in vehicle structures. In general, welded or notch sections, fatigue strength decreases because of increasing concentrated stress or effect of notch sensitivity and so on. In this paper, some methods are studied to improve fatigue strength and obtain a long life. 2 refs., 11 figs., 5 tabs.

Report on reuse of concrete and masonry in foreign countries; Concrete no recycle ni kansuru kaigai no doko

Energy Technology Data Exchange (ETDEWEB)

Yamato, T. [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

1997-07-01

Referring to the report by RILEM in 1976, this paper introduces the status and guidelines on recycling concrete in foreign countries. In Flanders, Belgium, a sub-committee was established in 1990 under the auspices of Environment Agency and the Ministry of Construction. Researches and investigations have been carried out to prepare flexible guidelines so that reclaimed aggregates may be used in public constructions. The Belgian Road Research Center, the Belgian Building Research Institute and its subsidiaries are supporting several investigation and research projects. In England, about 10% of aggregates is estimated to have been made of wastes and recycled materials. The seventh revised edition of the expressway construction specifications in the concrete aggregate standard BS882 has approved for use as an aggregate for pavement concrete if quality of crushed concrete meets the quality and grain size standard of BS882. Additionally, this paper shows a list of specifications and standards for reclaimed aggregates made in the U.S.A., France, Germany and other countries. 18 refs., 3 tabs.

Study about the effect of microgravity on biofunctions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A study is made for the elucidation of the effect of microgravity on biofunctions. The protoplast of shiitake is exposed to microgravity and then cultured, and a significant difference occurs. The rate of colony formation by cell fusion in the test sector is found to be two times higher than that in the control sector. When swimming ciliates which are unicellular are suddenly exposed to microgravity, their swimming speeds changed differently according to the direction of swimming. When a mouse subjected to acupuncture for three days is exposed to microgravity, its water metabolism and excretory function are enhanced. A mouse treated with Chinese medicine reacts in the similar way. The change due to microgravity in the amount of acetylcholine in the hypothalamus is found characteristically time dependent. Mice infected with lethal herpes viruses just after exposure to microgravity die at a rate in proportion to the number of exposures and to the amount of viruses given. The migration speed of chemical stripes in case of a gel-base BZ (Belousov-Zhabotinsky) reaction under microgravity is equal to that on the ground. The trigger wave migration speed in case of a water solution-base BZ reaction under microgravity is reduced to approximately 80% of the speed on the ground. 12 refs., 31 figs., 3 tabs.

Technology assessment on a hydrogen fueled aircraft system; 1980 nendo suiso nenryo kokuki system ni kansuru technology assissment

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper describes technology assessment on a hydrogen fueled aircraft system. Indispensable as technological assignments are structuring different safety systems including prevention of leakage and ignition, not to speak of developing an airframe structure that considers cryogenic and brittle nature of liquefied hydrogen. Operation related industries would be subjected to increased burdens, such as purchase and servicing of new implements and materials, but the liquefied hydrogen industry will have a chance of growing largely with wide repercussions. In the environmental aspect, the aircraft will have less CO and SOx emission in exhaust gas and lower noise than the conventional jet aircraft. Technological problems to be solved in the development include the safety of fuel tanks, safety assurance measures, and liquefied hydrogen of the required amount to be supplied easily and at low cost. To meet these requirements, noticeable progress is demanded in hydrogen manufacturing technologies. What is also required is explosion-proof safety that does not have to require crews to take special considerations in take-off and landing, not to speak of during flight. This also applies to fuel feeding and servicing on the ground. Considerations must be given that rise in operation cost should not be excessive. (NEDO)

Heat transfer simulation in a furnace for steam reformer. Gas kaishitsu ronai no dennetsu simulation ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kudo, K; Taniguchi, H; Guo, K [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering; Katayama, T; Nagata, T [Tokyo Gas Co. Ltd., Tokyo (Japan)

1991-01-10

This paper discusses the heat transfer analysis in a furnace for LPG reforming to produce gas enriched hydrogen. The three-dimensional combined radiative and convective heat transfer processes in a furnace for LPG reforming is simulated by introducing the radiosity concept into the radiative heat ray method for an accurate radiative heat transfer analysis. Together with an analysis of the chemical reaction in the reactor tubes of the furnace, the heat transfer simulation gives the three-dimensional profile of the combustion gas temperature in the furnace, the tube-surface heat-flux distribution and the composition of the reformed gas. From the results of the analysis, it was clarified that increasing the jet angle of the heating burner raises the gas temperature and the tube surface heat flux near the burner entrance, and that the flame shape is the most important factor for deciding the heat flux distribution of the tube surface because the heat transfer effect by flame radiation is much more than that by convection of the combustion gas. 18 refs., 9 figs., 2 tabs.

Mechanical properties of weft knitted fabric reinforced composites. Iamimono kyoka fukugo zairyo no rikigakuteki tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Wu, W.; Inoda, M.; Kotaki, M.; Goto, A.; Fujita, A.; Hamada, H.; Maekawa, Z. (Kyoto Institute of Technology, Kyoto (Japan). Faculty of Textile Science)

1993-09-15

Mechanical properties and failure behavior of weft knitted fabric reinforced composites were studied. Aramid fiber was used as reinforcement (knitting fiber), and epoxy resin as matrix. Different tensions were applied to the weft knitted fabric in a course or wale direction to prepare 5 kinds of fiber reinforced composites with different densities of the knitted fabric, and tensile test pieces were thus provided by cutting each composite in a course or wale direction. As a result, the weft knitted fabric reinforced composite offered a dynamical anisotropy, and the tensile strength of the test pieces was higher in wale direction than course one. Fracture in a course direction occurred at the section with extreme low fiber content, while fracture in a wale direction occurred at a loop interlocking region due to stress concentration. The tensile strength was constant or increased in a course or wale direction by stretching the knitted fabric before molding, respectively. 21 refs., 15 figs., 2 tabs.

Fundamental characteristics on electric system of solar electric vehicle; Solar car no denki keito ni kansuru kiso tokusei

Energy Technology Data Exchange (ETDEWEB)

Fujita, S; Sasaki, M; Kaga, T; Koyama, N [Hachinohe Institute of Technology, Aomori (Japan)

1996-10-27

The electric system of a solar vehicle was removed and the fundamental characteristics examined in order to carry out a basic experiment on the electric system. Using a basic circuit with panels, batteries and loads connected, the voltage and current were measured in the presence/absence of the trackers, batteries, etc., and then, their effects were examined. Simultaneously, the quantity of solar radiation was also measured. The lowering of the output voltage was somewhat relaxed with the use of the trackers. Further, with the trackers used, the output voltage of the panel was small in spite of a large quantity of solar radiation compared to the case without the trackers, which was due to the restriction of the output voltage by the trackers. When measured without batteries, the output voltage of the panel was such that the load current was also influenced by the variation of insolation, so that, with a large decrease in insolation, the load current was decreased with the supply of current suspended from the panel. 7 figs., 1 tab.

On the relationship between stacking process and resolution. 2; Jugo shori to bunkaino ni kansuru kiso kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T; Miyazaki, M [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

With respect to concept of resolution in seismic exploration using the reflection method, detailed considerations were given on processes of forming the resolution as a result of arranging observation points at vibration transmitting and receiving points. In the discussion, numerical experiments were carried out, in which the scattering stacking process is applied in a model having one scatterer existing in homogeneous media. The experiments investigated an imaging formation process of the scatterer when arrangement of the vibration transmitting and receiving points were changed from a coarse condition to a dense condition while the number of transmitting and receiving points is being increased. Resolution is created if waveforms having finite frequencies are used as input, and the imaging is performed by utilizing the limited number of vibration receiving and transmitting points. If the concept of equi-travel plane is used under these conditions, the equi-travel planes perform negation with each other, and it was indicated that visual resolution is expressed by how good the negating effect is. It was discovered that such concept of the resolution is quite ambiguous in terms of engineerings. 2 refs., 17 figs.

Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

Study on grout-filled coupling steel sleeve; Kokan sleeve wo mochiita grout jutenshiki tekkin tsugite ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Y. [Osaka University, Osaka (Japan)

1997-06-01

Newly designed grout-filled coupling sleeve is discussed, which uses as the sleeve an electric resistance welded tube with protrusions formed in a checker pattern on its inner wall and is capable of using various premixed grouting materials available on the market. Specimens are subjected to uniaxial tensile loading and positive/negative cyclic loading, and the impact of various factors on the basic performance of the specimens and their stress/distortion characteristics at local spots in the reinforcing bar are disclosed. In the positive/negative cyclic loading in the plastic region, however, such findings are not obtained. In view of the stress/distortion characteristics at local spots in the reinforcing bar, a method is proposed for estimating the coupling strength and fracture type. A method for estimating the deformation behavior of the coupling, however, is not proposed. Investigations are conducted into the manufacture and installation of the grout holding framework, coupling fixing jigs, plugs, etc., and it is found that precasting should be studied in the future. 38 refs., 156 figs., 30 tabs.

Performance analysis on natural energy autonomous house (HARBEMAN house); Shizen energy jiritsu house (HARBEMAN house) ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1996-10-27

To reduce fossil fuel consumption and CO2 emission, this article introduces an actually constructed natural energy autonomous house. It has a solar collector on the south roof for hot water supply and a sky radiator on the north roof for cooling water supply. The sky radiator uses radiation cooling phenomena into the space by electromagnetic wave through the window of atmosphere. This house also has an insulated tank with a capacity of 31 m{sup 3} in its underground. In the long-term heat storage mode, the heat is collected through the solar radiation during the period from summer to spring and is stored in the underground water tank, to use it for heating and hot water supply in winter. The heat can be recovered from the garbage waste incinerator. A gas fired auxiliary boiler is used for the shortage. In the long-term heat regeneration mode, the heat is regenerated through the sky radiator during the period from spring to summer and is stored in the underground water tank, to use it for cooling in summer. For the shortage, the water is cooled using a heat pump operated by the midnight power. The insulating performance is improved by using the pair glass in windows and the glass wool in the walls. Rain water is collected in a tank with a capacity of 2 m{sup 3}, to use it for toilet water. Annual energy and water saving is equivalent to 600,000 yen. 10 refs., 10 figs., 2 tabs.

Study on box shield tunneling method in trial field operation; Box shield koho jissho seko ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Tada, K.; Taniguchi, T. [Toda Corp., Tokyo, (Japan); Furukawa, K.; Nakagawa, K. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering

1997-03-20

This paper describes a rectangular section shield tunneling method as a part of developments of non-circular section shield tunneling methods. The non-circular shield is drawing attention because of need of excavation in small land available in urban areas and between congested existing structures, as well as reduction in the excavated soil amount. A full-scale machine was fabricated to perform a natural ground excavation experiment. The cutter units comprising two each of drum cutters and ring cutters were arranged above and below, by which two tunnels of 40 m long with a cross section of 2.85 m {times} 2.85 m were excavated. The natural ground was supported safely by holding mud water pressures at cutting points constant, thus stability of the cutting points was ensured. Back-filling has made complete filling of tail void (clearance between a segment and the ground) possible, resulting in suppression in conditional change of the surrounding ground. Attitude control has been performed properly as a result of correct selection of shield jacks and use of deflection jacks. Broken-type over-cutters were used to have constructed tunnels with curve radius of 80 and 100 m with high accuracy. Thrust and propulsion speed of the shield do not differ from those of circular shields. Possibilities of this construction method were verified. 8 refs., 26 figs., 2 tabs.

Study on molecular controlled mining system of methane hydrate; Methane hydrate no bunshi seigyo mining ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kuriyagawa, M; Saito, T; Kobayashi, H; Karasawa, H; Kiyono, F; Nagaoki, R; Yamamoto, Y; Komai, T; Haneda, H; Takahashi, Y [National Institute for Resources and Environment, Tsukuba (Japan); Nada, H [Science and Technology Agency, Tokyo (Japan)

1997-02-01

Basic studies are conducted for the collection of methane from the methane hydrate that exists at levels deeper than 500m in the sea. The relationship between the hydrate generation mechanism and water cluster structure is examined by use of mass spectronomy. It is found that, among the stable liquid phase clusters, the (H2O)21H{sup +} cluster is the most stable. Stable hydrate clusters are in presence in quantities, and participate in the formation of hydrate crystal nuclei. For the elucidation of the nucleus formation mechanism, a kinetic simulation is conducted of molecules in the cohesion system consisting of water and methane molecules. Water molecules that array near methane molecules at the normal pressure is disarrayed under a higher pressure for rearray into a hydrate structure. Hydrate formation and breakdown in the three-phase equilibrium state of H2O, CH4, and CO2 at a low temperature and high pressure are tested, which discloses that supercooling is required for formation, that it is possible to extract CH4 first for replacement by guest molecule CO2 since CO2 is stabler than CH4 at a lower pressure or higher temperature, and that formation is easier to take place when the grain diameter is larger at the formation point since larger grain diameters result in a higher formation temperature. 3 figs.

Performance test of deodorants for ammonia gas; Ammonia gas ni taisuru dasshuzai no seino kentei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yano, H.; Hashimoto, S.; Yonemura, S. [Shimizu Corp., Tokyo (Japan); Shoda, M. [Tokyo Institute of Technology, Tokyo (Japan)

1998-01-10

This paper presents the results of performance tests of various kinds of adsorbents by static and dynamic adsorption methods to select the optimum deodorant (adsorbent) for ammonia gas (NH3). In the performance test of the static adsorption method, the amounts of NH3 adsorbed by 21 kinds of adsorbents including physical and chemical adsorbents were measure. The amounts adsorbed physical adsorbent No. 6, chemical adsorbents Nos. 18, 19 and 20 which showed higher adsorption ability were 0.0160g/g, 0.0284g/g, 0.0250g/g, and 0.0249g/g respectively at 30degC under equilibrium pressure of 50 mmHg. All of the adsorbent showed in Freundlich`s adsorption isotherm for NH3. Although the correlation between specific area, pore volume, mean pore radius, pH each adsorbent and the amount of adsorbed were tried, the correlation between the pH and the amount of NH3 adsorbed was significant. This suggests that the pH is a proper criterion for selection for adsorbents. The performance test of the dynamic adsorption method, was conducted for adsorbents Nos. 6, 18, 19 and 20 above-mentioned. The 10% breakthrough time was compared as the performance index. The breakthrough time of the adsorbent which the amount adsorbed was large was long but the breakthrough time was not proportional to the amount adsorbed. These results suggest that the performance test only by the static adsorption method is insufficient and that the breakthrough time test by the dynamic adsorption method is essential. 13 refs., 10 figs., 4 tabs.

Primary study on quantitative evaluation of driver fatigue; Unten hiro no teiryo hyoka gijutsu ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Noguchi, Y; Mochizuki, M; Toyofuku, K [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Katsuura, T [Chiba University, Chiba (Japan)

1997-10-01

Quantitative evaluation of physical and mental loads are effective in developing more human-friendly vehicles. Here attention has been focused on the mental load. Attempts were made to find some physiological indices that can be used for quantifying the mental load and resultant fatigue. Subjects were told to perform three different tasks in a climatoron, and the relation between physiological indices and their perception of fatigue as well as their capability of performing the tasks were analyzed. As a result, heart rate variability is a good index for quantitative evaluation of mental load and fatigue. 5 refs., 4 figs., 6 tabs.

Hydrogen energy technology development conference. From production of hydrogen to application of utilization technologies and metal hydrides, and examples; Suiso energy gijutsu kaihatsu kaigi. Suiso no seizo kara riyo gijutsu kinzoku suisokabutsu no oyo to jirei

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-02-14

The hydrogen energy technology development conference was held on February 14 to 17, 1984 in Tokyo. For hydrogen energy systems and production of hydrogen from water, 6 papers were presented for, e.g., the future of hydrogen energy, current state and future of hydrogen production processes, and current state of thermochemical hydrogen technology development. For hydrogen production, 6 papers were presented for, e.g., production of hydrogen from steel mill gas, coal and methanol. For metal hydrides and their applications, 6 papers were presented for, e.g., current state of development of hydrogen-occluding alloy materials, analysis of heat transfer in metal hydride layers modified with an organic compound and its simulation, and development of a large-size hydrogen storage system for industrial purposes. For hydrogen utilization technologies, 8 papers were presented for, e.g., combustion technologies, engines incorporating metal hydrides, safety of metal hydrides, hydrogen embrittlement of system materials, development trends of phosphate type fuel cells, and alkali and other low-temperature type fuel cells. (NEDO)

FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports presented to the international workshop for selective oxidation catalysts); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo kokusai seminar jigyo shiryo. Sentaku sanka shokubai kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the international workshop for selective oxidation catalysts, promoted by RITE. The session of methane activation includes a comprehensive lecture on designs of selective alkane oxidation catalysts developed since the 1980s, describing the simplified catalyst design procedures and, at the same time, pointing out the vapor-phase reactions governing the overall reactions at high temperature. The session of alkane oxidation includes a lecture on oxidation of ethane into acrolein in the presence of a silica catalyst supporting isolated active sites, stressing necessity for controlling the vapor-phase reactions and importance of isolating the active sites. The session of crystalline materials includes a lecture on Ti-siting in Ti-containing molecular sieve and selective oxidation catalyst functions, concentrating discussion on oxidation with H{sub 2}O{sub 2} as the oxidant on TS-1. The session of engineering hybrid includes a lecture on catalytic partial oxidation of alkanes in millisecond reactors, describing that possibility of controlling the vapor-phase reactions in the presence of monolith, porous-plate catalysts in a reactor through which the reactant gases pass in a very short time, of the order of millisecond. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Substitution No.1). Achievement report on development of biogasification process for low coalification degree coal; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (daitai No.1). Teisekitankadotan no biogas ka process kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this biogasification process, coal is subjected to pretreatment and then experiences methane fermentation. The aim is to reduce the amount of CO{sub 2} per unit thermal equivalent to be generated by low coalification degree coal. The electrolytic oxidation technology for coal pretreatment is developed jointly with ESC (Electrosynthesis Company, Inc.), U.S. For the development and improvement of electrolytic oxidation technology, the experimenting electrolytic tank of ESC and a small-scale electrolytic oxidation unit developed by the same are used. Using the developed electrolytic oxidation technology, coal is made meltable at a rate of 2.93%/min, which means that 80% or more of the coal turns meltable in 30 minutes. The technology has its own problem, however, that the power consumption rate is high. The report comprises nine chapters, including (1) the goal and background of research and development, (2) enhancement of research and development, (3) electrolytic oxidation of low coalification degree coal, (4) methane fermentation, (5) prospect of practical application, (6) reference materials and list of literature, and (7) reports on research tours overseas. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Novel No.3). Achievement report on research and development of highly adaptive prosthetic upper limbs; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (shinki No.3). Tekiogata joshi hosogu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop prosthetic upper limbs easy to operate and high in reliability. Development activities are conducted in the three fields of (1) the study of a sensor feedback type power-driven prosthetic hands, (2) development of a power assist for upper limbs, and (3) the goal and self-evaluation. In field (1), pending problems are taken up, evaluation (Jet Propulsion Laboratory of National Aeronautics and Space Administration, U.S.) is made, evaluation report is studied, new objects of development are named, and power-driven prosthetic hands are manufactured. As the result, small and light prosthetic hands are built, capable of performing delicate acts. They want more grasping power, however, and want improvement. In field (2), the development goal is studied, and efforts are made to develop a power assist mechanism. As the result, a basic mechanism that can bend and extend each of the fingers is now complete although some problems remain to be solved for the users to operate them conveniently in their daily life. The technologies mentioned in this report may be applied also to massaging instruments, power input devices for robotic manipulators, and a force feedback aided situation recognition system utilizing the power transmission mechanism. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen gas turbine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso gas turbine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-31

This research aims at establishment of the meaning of using hydrogen as gas turbine fuel in the hydrogen energy system and various conditions for hydrogen gas turbines, and approaches to the feasibility study and R and D of hydrogen gas turbines in the future. In fiscal 1975, researches were made on (1) feasibility study on hydrogen-oxygen gas turbine, (2) establishment of various conditions for technical, social and economic realization of hydrogen gas turbines in the total energy system, and (3) study on technical troubles to be solved for realization of hydrogen gas turbines. For the above researches, study was made on hydrogen combustion based on the hydrogen combustion test result of gas mixture including hydrogen, and on the feasibility of aphodid cycle. In addition, study on the applicability of hydrogen-oxygen gas turbines, comparative study on hydrogen-oxygen gas turbine, MHD power generation and fuel cell, and the future prospect of hydrogen gas turbines for ships were made to place this hydrogen gas turbine. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

Fiscal 1998 research report. Feasibility study on international cooperation for technology transfer; 1998 nendo chosa hokokusho. Gijutsu iten ni kakawaru kokusai kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

CTI (Climate Technology Initiative) is a framework for use by developed countries in international cooperation and voluntary promotion of the development and diffusion of technologies contributory to reduction of greenhouse gas emissions. The CTI's activity goal is to accelerate the transfer and diffusion of technologies for climate change control. As the first step toward personnel development programs relating to energy efficiency, CTI organized its workshop on that theme. The results of the workshop have been examined, and its achievements were reported at COP4 meeting, while responses by participatory countries were studied to evaluate the potential of international cooperation with regard to personnel development for reducing greenhouse gas emissions. In fiscal 1998, the CTI workshop 'Energy Efficiency' was held. The participants from developing countries understood the necessity and importance of energy saving enough through discussions in the workshop, and announced their message toward the world at COP4 meeting. (NEDO)

Fiscal 1998 research report on the international cooperation for techniques of rational energy use; 1998 nendo energy shiyo gorika shuho kokusai kyoryoku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For promotion of the implementation of LCA, 'Japan-Europe joint project for LCA (life cycle assessment) of photocopiers' was established. The following organizations were selected for this project; Material Research Institute of the Swiss Confederation (EMPA), PE Engineering (PE) consortium and Stuttgart University (IKP) of Germany, Leiden University of the Netherlands (CML), and Pre Consultant of the Netherlands as the European coordinator of the project. The project includes the following as issues: The estimation method of material composition/production process data from parts names, practical data items (kind of materials, inventory data) used by European institutes, the guidance for construction of Japanese LCA database, and the viewpoint of inventory accuracy. The following are also reported: the limitation of possible impact assessment based on current inventory analysis data, the viewpoint on the time dependence and regional one of impact assessment, and the viewpoint on integration of impact assessment. (NEDO)

Fiscal 1999 survey report. Survey of international cooperation over energy use rationalization techniques; 1999 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the past, studies have been conducted involving the possibility of development of information offering techniques for the realization of sustainable society, for which LCA (life cycle assessment) as a tool for reducing energy consumption and environmental impact is investigated and case studies are conducted in this connection. In this fiscal year, for the purpose of deliberating how to utilize the LCA results, a survey is conducted of how LCA is being used as a tool for constructing an environmental management system set forth in the ISO14000 series, by holding conferences with LCA researchers representing the respective countries involved. Investigations are conducted into the actualities of the environmental management system, environmental performance assessment, and environmental labelling whose standardization has been under way in compliance with the ISO14000 series, into the actualities of matters relating to assessment techniques and decision making such as environmentally-friendly designing, supply chain management, reports on environments, etc., which are becoming established in enterprises, and into the actualities of access to and disclosure of information. International cooperative researches are conducted, participated in by five leading organizations of Sweden, Germany, Denmark, and Canada, and Japan's National Institute for Resources and Development, where actual states of LCA utilization are introduced and improvement on LCA techniques are discussed. (NEDO)

Fiscal 1999 survey report. Survey of international cooperation over energy use rationalization techniques; 1999 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the past, studies have been conducted involving the possibility of development of information offering techniques for the realization of sustainable society, for which LCA (life cycle assessment) as a tool for reducing energy consumption and environmental impact is investigated and case studies are conducted in this connection. In this fiscal year, for the purpose of deliberating how to utilize the LCA results, a survey is conducted of how LCA is being used as a tool for constructing an environmental management system set forth in the ISO14000 series, by holding conferences with LCA researchers representing the respective countries involved. Investigations are conducted into the actualities of the environmental management system, environmental performance assessment, and environmental labelling whose standardization has been under way in compliance with the ISO14000 series, into the actualities of matters relating to assessment techniques and decision making such as environmentally-friendly designing, supply chain management, reports on environments, etc., which are becoming established in enterprises, and into the actualities of access to and disclosure of information. International cooperative researches are conducted, participated in by five leading organizations of Sweden, Germany, Denmark, and Canada, and Japan's National Institute for Resources and Development, where actual states of LCA utilization are introduced and improvement on LCA techniques are discussed. (NEDO)

Fiscal 1998 research report. Feasibility study on international cooperation for technology transfer; 1998 nendo chosa hokokusho. Gijutsu iten ni kakawaru kokusai kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

CTI (Climate Technology Initiative) is a framework for use by developed countries in international cooperation and voluntary promotion of the development and diffusion of technologies contributory to reduction of greenhouse gas emissions. The CTI's activity goal is to accelerate the transfer and diffusion of technologies for climate change control. As the first step toward personnel development programs relating to energy efficiency, CTI organized its workshop on that theme. The results of the workshop have been examined, and its achievements were reported at COP4 meeting, while responses by participatory countries were studied to evaluate the potential of international cooperation with regard to personnel development for reducing greenhouse gas emissions. In fiscal 1998, the CTI workshop 'Energy Efficiency' was held. The participants from developing countries understood the necessity and importance of energy saving enough through discussions in the workshop, and announced their message toward the world at COP4 meeting. (NEDO)

Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-04-20

Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

Investigations on steel slag re-utilization in developing countries; Hatten tojokoku ni okeru tekko slag sairiyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to promote steel slag re-utilization in developing countries, a possibility was presented for technical cooperation to India, Indonesia and Thailand upon putting the status of slag utilization in Japan into order. Blast furnace slag produced in Japan (having a re-utilization rate of 95%) is re-utilized and processed as cement aggregates and road beds, and converter slag as civil engineering materials and ores. Steel making slag (having a re-utilization rate of 80%) is re-utilized as road, processing and civil engineering materials. Since the steel making slag faces intensifying competition with ash made by incinerating construction and general wastes, it is important to improve its price competitiveness or mixed utilization with other materials. Re-utilization has not advanced to a recognizable level in developing countries because of having no difficulty for availability of lands for wastes. However, growth of full-scale steel industries and elevation in tendency of environment preservation now urge increase in the slag re-utilization rate. Required to achieve the goal would include wider use of re-utilization technologies, quality control on slag, joint use of facilities to produce re-utilization products, and governmental assistance on burdens of transportation cost. Assistance from Japan is expected to help meet these requirements. 25 figs., 31 tabs.

Committee report on visual appearance of neon lights. Neon no hikari no miekata ni kansuru tokubetsu kenkyu iinkai hokoku

Energy Technology Data Exchange (ETDEWEB)

Kansaku, H. (Chukyo University, Nagoya (Japan). Faculty of Letters)

1991-04-25

Were summarized the results of experiments and literature searches, conducted by the Commettee on Visual Appearance of Neon Lights,'' which was set up to provide scientific and basic data for understanding of relationship between neon lights and psychological reaction of human, and for realizing of neon sign advertisements with playing a role as neon lights and without any environmental problems. Analytical results of influences of six colors, such as red, yellow, green, blue, violet, and white, brightnesses, and flickering frequencies to the psycological reaction of human on the direct observations of neon lights were described. Results of influences of the neon light incidence into the room to the psychology of residents were also introduced. Furthermore, evaluation of neon lights as an aspect was discussed. Consequently, based on the combination of activity and estimativity, some attentions to be payed on the setting-up of neon lights were pointed out. A red flickering neon light'' was given as clearly a bad example. 2 figs.

Survey on bio-chemical complex harmonized with global environment. 3; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A survey was conducted of bio-chemical complex harmonized with the global environment for the purpose of constructing the material production process harmonized with the environment by the process fusion between biological conversion and chemical reaction. Palm oil was taken up as renewable raw material plant resource. The process utilizing bio-chemical reaction advances at normal temperature and pressure and is high in reaction specificity and selectivity. This is a recycling, circulation and environmental harmony type production technology which brings high yield, energy conservation, resource conservation, and low environmental loads. Waste water treatment and production of useful substances from sludge were thought as elementary technology. A possibility was studied of enzyme production by culturing solid waste, and the enzyme was applied to the hydrolysis process. The paper indicated trace components in the palm oil and the extraction method and proposed the production process of new derivatives for adding value to hydrolysate. A study was also made of the overall process flow which integrated these new processes and the material balance. The comprehensive evaluation of this new process was made from the aspect of the product structure, the market, construction cost, economical efficiency, and the environment. 133 refs., 65 figs., 56 tabs.

Subjects on geochemical technology for geothermal power plant. Chinetsu hatsudensho ni okeru kagaku kanri gijutsu ni kansuru shomondai. 1

Energy Technology Data Exchange (ETDEWEB)

Hirowatari, K [Kyushu Electric Power Co. Ltd., Fukuoka (Japan)

1991-04-30

This paper introduces the following technologies and countermeasures found to be successful in solving geochemical problems relating to the maintenance and management of geothermal power plants belonging to Kyushu Electric Power Co., Ltd. In controlling condensate properties,curtailment of pH fluctuation range by changing the injection point of NaOH,inactivation of sulphur bacteria by using chloramphenicol and prevention of slime loading of the condenser strainer by running of the cooling tower without make-up water were achieved. In the environmental countermeasures,it was concluded that Fe-ion injection method was most effective to remove As out of waste hot waters which are all reinjected into the underground formation now. By understanding the characteristics of the well eruption fluids,the attenuation mechanism of steam producing wells could be estimated, which were interference,re-eruption and degradation of the reservoir temperature caused by the reinjected hot waters. And the problems associated with the attenuation of steam producing wells have been solved fundamentally by taking proper countermeasures to eliminate the influence of reinjected hot waters. The atteunuation of reinjection well was found to be caused dominantly by silica loading at the permeable zone of wellbore and to be effectively solved by high temperature reinjection of the waste hot waters, controlling of temp. degradation of hot waters to be reinjected and prevention of air mixing. After applying proper countermeasures, the attunuation rate of the reinjection well has been fairly improved. 13 refs., 21 figs., 2 tabs.

Study on evaluating method for earthquake resisting performance of steel piers; Kosei kyokyaku no taishinsei ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Isoe, A.; Hashimoto, Y.; Morimoto, C.; Sakoda, H.; Ishige, T.; Yoshikawa, T.; Kishida, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1998-12-20

After the shock of Hyogoken Nanbu Earthquake in 1995, protection against level 2 earthquake becomes important subject for civil structures. Subsequently plastic design methods for steel piers have been studied and rapidly introduced. The authors developed a method to evaluate the earthquake resisting performance of a steel pier with a single mass model. This model is useful for design because of its simplicity but on the other hand it can not consider the effects of piers` interaction in space. To include this effect in an analysis a simple 3 dimensional calculation model of box-column pier is developed. (author)

Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

Investigations on installation of the heat exchange system in geothermal wells; Chinetsu koseinai netsukokan system donyu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The heat exchange system in geothermal wells is a system that replaces the air source heat pump and uses underground beds or groundwater as a heat source to heat rooms by collecting underground heat in winter, and cool rooms in summer by operating a heat media circuit in reverse direction through the action of a reverse flow valve to discharge heat underground. This paper describes feasibility investigations on the system including its technical trend for introducing the system technology. Technological and economic discussions were given by classifying the intra-well heat exchange device in its installation direction (horizontal loop type and vertical installation type), underground heat exchange media (antifreeze solution/water cyclic system and direct expansion system), and underground heat transfer (heat conduction system and heat convection system). As a result of discussing each system, it was concluded that the following two systems are promising: A = vertical installation, antifreeze solution/water cyclic and heat conduction system, and B = vertical installation, antifreeze solution/water cyclic and heat convection system. Since the system B was found to have better efficiency and economy among both systems, it is necessary to verify an intra-well heat exchange system and operation methods that suit the system B effectively. 21 refs., 8 tabs.

Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatani, T. [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K.; Moriyoshi, N. [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T. [Nagoya Institute of Technology, Nagoya (Japan)

1996-12-31

Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N; Omata, K [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

Consideration on local blast vibration control by delay blasting; Danpatsu happa ni yoru kyokuchiteki shindo seigyo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Mogi, Gento; Adachi, Tsuyoshi; Yamatomi, Jiro [The University of Tokyo School of Engineering Department of Geosystem Engineering, Tokyo (Japan); Hoshino, Tatsuya [Mitsui Mining and Smelting Corp., Tokyo (Japan)

1999-10-31

In this research, local blast vibration control based on the theory of superposition of waves was investigated. Firstly, the influence of delay time errors of conventional electric detonators upon the level of local blast vibration was examined. Secondly, for a further effective local blast vibration control, a new delay blasting design concept 'combined delay blasting' that postulates the use of electronic detonators, which virtually have no delay time errors, is proposed. For a delay blasting with uniform detonation time intervals, an optimum time interval to minimize the local PPV (Peak Particle Velocity) is obtained based on the relationship between the PPV and the time interval, which is derived by superposing identical vibration time histories of each single hole shot. However, due to the scattering of the actual delay time caused by errors, PPV of a production blast seldom coincides with the estimated one. Since the expected value and the variance of PPV mainly depend on sensitivity of PPV around the nominal delay time, it is proposed that not only the optimum but also several sub-optimum candidates of delay time should be examined taking error into consideration. Concerning the 'combined delay blasting', its concept and some simulation results are presented. The estimated reduction effect of blast vibration of a delay blast based on this concept was quite favorable, indicating a possibility for further effective local blast vibration control. (author)

Study on torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kojima, N; Kishimura, K [Meiji University, Tokyo (Japan)

1996-10-27

Discussing the rotor blades of the torsion arc blade type (TABT) wind turbine, difference in windmilling characteristics was determined between elliptic blades and rectangular blades by theoretical analysis and model experiment. Experimental generation of power was carried out using a test wind turbine in the natural wind. First, elliptic blades were bent into arcs and fixed to shaft. The action force was determined calculating the blade area and the wind velocity vertical thereto. Furthermore, the force in the direction to turn the rotor was determined with the effect of the part behind the blade taken into account. The rotation-curbing air resistance in the flank direction that a rotor experiences was subtracted to determine the torque generated. A formula was derived for the elliptic blade. Second, a formula was derived in the same way for the case of rectangular blades. In conclusion, in the case of 6-blade wind turbine, the rate of responsibility for wind turbine rotation of the part behind the blade was approximately 50% of the part in front of the blade. Shape coefficients were introduced into the theory, which resulted in values agreeing well with values obtained from experiments. Elliptic blades yielded more power than rectangular blades at the same wind velocity. High in durability, the TABT wind turbine is expected to be put into practical use as a compact auxiliary power generating device. 2 refs., 14 figs.

Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

1996-02-15

To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

Comparison about the bone material examination of JIS and ISO; Honezai shiken ni kansuru JIS to ISO no hikaku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Sumie.; Yanagi, Kei.; Shimura, Akiharu.; Murohoshi, Shiori. [Japan Testing Center for Construction Materials, Tokyo (Japan)

1998-12-01

There are various things in slug bone material and so on manufactured from the macadam, crumble sand. Which crushed rock including gravel, sand to produce in the nature and which was manufactured, and a lightweight bone material and the industry by-product with the bone material used for the concrete. It is necessary with a bone material to grasp the nature of the bone material itself properly to occupy about 70% of the capacity in the concrete and to manufacture the good concrete of the quality from the influence that influence to the various concrete materiality that quality being big. When the quality of a bone material to use for the concrete is confirmed, an examination is being done in accordance with the way of examining it established as the Japanese industry standard in our country. (NEDO)

Investigational study on construction of the physical function database; Shintai kino data base no kochiku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

An investigational study was carried out on construction of the physical function database which can supply data useful for planning, design and production when companies provide products and barrier-free environment for the aged society. Up to now, the final image of database was studied as to the visual function. In addition, this study is aimed at constructing the physical function database. In the literature survey, basic data on physical characteristics of the aged which have lain scattered were collected and systematically sorted in relation to the exercise function in order to make an analysis of the data and measuring technology in terms of reliability, importance, and applied values. In the survey of corporate needs, an examination of concrete needs for the exercise function and auditory function was made for general companies and companies related to the medical and welfare apparatus field. As to the visual function, a study was conducted on selection of new items for visual measurement and measuring methods. In the study of the database structure, a pilot database was constructed and subjects were extracted. 529 refs., 57 figs., 15 tabs.

Report on the actual situations of the commercially applied, industrial robots; Sangyoyo robot ni kansuru kigyo jittai chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

Described herein are the actual situations of industrial robots as the FY 1991 questionnaire survey results. The questionnaires were sent to 541 factories, and 74% thereof were recovered. The major machine types fall into categories of manual manipulator, stationary sequence manipulator, remote controlling robot, sequence robot, playback robot, numerically controlling robot and intelligent robot. They are mainly driven by hydraulic, pneumatic, or electrical power. Their mechanism types cover polar coordinate, cylindrical coordinate, rectangular coordinate and articulation types, among others. They are mainly controlled by electronically, electrically (hydraulic or relay), or pneumatically. The major purposes for general works include casting, forging, resin processing, heat treatment, pressing, welding, coating, machining, cutting, assembling, reception/delivery of goods, and testing/inspection. The special works they are in service include those for power/gas/water services, construction works, and research and development. By work step, they are in service, e.g., for loading/unloading goods, palletising/packing goods, supporting, screening, welding, spraying/coating, grinding, clamping, assembling, and riveting. (NEDO)

Investigation on vibrational dampers for cables of Tsurumi Tsubasa bridge; Tsurumi tsubasabashi no keburu seishin hoshiki ni kansuru jisho

Energy Technology Data Exchange (ETDEWEB)

Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Public Corp., Tokyo (Japan); Yamada, H. [Yokohama National Univ. (Japan)] Murakami, T. [NKK Corp., Tokyo (Japan). Applied Technology Research Center

1998-03-20

In a long cable-stayed bridge, countermeasure against wind induced vibration should be often taken at the same time together with the measure against angular bent phenomena (phenomena in which secondary bending stress is generated on the front of fixing socket by live load). The conventional countermeasure is a combined use of buffer rubber and dampers. This study points out problems in the conventional countermeasure on the application to the cables of the Tsurumi Tsubasa Bridge and combination of dampers and angular bending buffer device is examined. The result shows that a combined use of high-damping rubber and oil dampers enables installation of the dampers in a lower position while maintaining the performance and is excellent in the easiness in installation and maintenance and in aesthetic view. This system was applied to the Tsurumi Tsubasa Bridge and the effectiveness on damping and angular bending relaxation was confirmed through the model tests, and vibration tests and field observation on the cables. 9 refs., 20 figs., 7 tabs.

Study of hydrogen engine for a hybrid electric vehicle. 1; Hybrid denki jidoshayo suiso engine ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Iguchi, T.; Numata, T. Hiruma, M.; Yamane, K.; Nakajima, Y.; Furuhama, S. [Musashi Institute of Technology, Tokyo (Japan); Takagi, Y. [Nissan Motor Co. Ltd., Tokyo (Japan)

1998-10-15

Study was made on application of a hydrogen engine to series hybrid electric vehicle (SHEV). Power of 20kW (for steady driving of a vehicle of 1t in total weight on flat road surface at 100km/h), and NOx emission concentration equivalent to that of EZEV (equivalent zero emission vehicle) were used as target performance. One of the merits of using a hydrogen engine for HEV is that conventional high-reliability gasoline engines can be used as hydrogen engines only by a bit of modification. A modified conventional 4-cylinder 4-cycle gasoline engine was used for this study. Hydrogen gas was continuously supplied through an intake manifold for premixed combustion by spark ignition. Brake thermal efficiency was improved from 30.5% to 35.5% by use of a high compression ratio and reduction of friction loss. NOx emission concentration could be controlled within 10ppm by ultra-lean combustion even at excess air ratios over 2.5. Both high efficiency and low emission were achieved at the same time around 3000rpm in engine revolution. 4 refs., 12 figs., 1 tab.

Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatani, T [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K; Moriyoshi, N [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T [Nagoya Institute of Technology, Nagoya (Japan)

1997-12-31

Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

Fiscal 1995 investigation on biological fixation of carbon dioxide; 1995 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To cope with the global warming caused by CO2, an investigation was conducted into biological fixation. It is necessary to make a many-sided and comprehensive study on the mechanism of CO2 fixation, the scale (area and carbon holding density), the rate and the environmental impact of the introduction of the technology and the technical problems, and to make a quantitative evaluation of each of the methods in order to make them practical proposals. The global ecosystem is classified into the land biota and ocean biota, and each typical ecosystem was surveyed in terms of the surface area, the carbon holding amount (presently existing amount), the net primary production amount, the required nutrient salt amount, the transpiration rate, etc. Next, a discussion was made on the increasing effect of the carbon fixation amount by changing the present ecosystem from the aspect of scale and rate. At the same time, a study was carried out of energy efficiency, economical efficiency and problems. Last, elementary technology was taken up which seems to be important for implementing measures for the biological carbon fixation. As to the ocean, it is necessary to obtain information, which is not sufficient to utilize marine biota for CO2 fixation, especially on the mechanism of depth-direction transfer of organism and its quantitative grasp. As to the land, one of the measures is conversion of the ecosystem where the amount of carbon fixed is small to the ecosystem where the amount is large. 249 refs., 58 figs., 51 tabs.

Study on fault diagnostic system using modularized knowledge; Mojuru gata chishiki wo mochiita ijo shindan system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimada, Y.; Sayama, H.; Suzuki, K. [Okayama Univ. (Japan). Dept. of Industrial and Mechanical Engineering

1997-08-15

Recently, a fault diagnostic expert system was prosperously developed as an objective of chemical plants and nuclear power plants. In this paper, a fault diagnostic method using modularized knowledge was proposed, a fault diagnostic system was constructed for an experimental plant, and the effectiveness of this method was clarified by carrying out a fault diagnostic experiment. The characteristics of the proposed fault diagnostic system were as follows: The necessary knowledge for diagnosing faults was made into each process element. Based on this method, the revision and addition of a knowledge base could be carried out in each element, and the design change of a plant could be flexibly corresponded by only changing the related part of the process flow graph. The estimated results were stored into the working memory, not only faults of an element in which faults resulted could be estimated, but also the fault propagating path could be clarified. 8 refs., 6 figs., 3 tabs.

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports on photosynthetic CO2-assimilating enzymes by the international workshops); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo kokusai seminar jigyo shiryo. Kogosei CO2 kotei koso kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the reports on photosynthetic CO2-assimilating enzymes, presented to the international symposium. These enzymes are important for assimilating CO2 in air, maintaining the environments and production of foods. For genes and proteins, the topics include diversification and function evolution of the RuBisCO (ribulose 1,5-bisphosphate carboxylase/oxygenase) in the natural environments, in particular in microorganisms. For activity regulation of PEPC, the topics include three-dimensional structures of PEPC and phosphorylation mechanisms and activity regulation therefor. For activity regulation of RuBisCO, the topics include post-translational activity of the enzymes (e.g., methylated enzyme); molecular regulation mechanisms involved in the biosynthesis and decomposition of RuBisCO; and activity regulation mechanisms in the chloroplast. For leaf photosynthesis and RuBisCO, the topics include importance of enzymes and involved in-vivo reaction steps for leaf photosynthesis CO2 assimilation reactions. For function of PEPC, the topics include the biochemically and molecular biologically necessary and sufficient conditions for the C4 mechanism as the special photosynthesis mechanism. For transgenic approaches, the topics include procedure for allowing the RuBisCO gene of a dissimilar organism to function in the tobacco chloroplast, and introduction of enzymes involved in the C4 photosynthesis pathway in C3 plants. (NEDO)

Fiscal 2000 international energy use rationalization measures project. International energy consumption efficiency improvement technology diffusion project - Green helmet project (Thailand: Report on heating furnace energy conservation seminar); 2000 nendo. Kokusai energy shiyo gorika to taisaku jigyo, Kokusai energy shohi koritsuka to gijutsu fukyu jigyo, Green helmet jigyo (Thai : kanetsuro shoenergy seminar hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The above-named seminar was held in Bangkok, Thailand, on January 30, 2001, and covered three kinds of industries of ceramics, glass, and aluminum. Approximately 200 people attended the meeting, consisting of NEDO (New Energy and Industrial Technology Development Organization)-affiliated people and 16 lecturers from Japan, and Thai participants. The seminar comprised a 'keynote address' and 'lectures on engineering' that aimed at the three industries as a whole, and 'lectures on engineering' and 'cases and activities for energy conservation' that aimed, respectively, at the three industries. Lectures were delivered on operating technologies which were already in practical use and on state-of-the-art technologies. The keynote address, entitled 'Global warming prevention and industrial furnaces,' covered the results of the 'High-performance industrial furnace field test project.' The lectures on engineering dealt with the 'instrumentation control system' and 'heat insulation technology' which were basic technologies for energy conservation and 'diagnosis technology and practice' which aimed at the enhancement of energy conservation after the start of operation. Questions and answers were earnestly exchanged. (NEDO)

FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 2. Examination and promotion of measures to obtain international understanding and cooperation; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 (kokusai kyoryoku shuishin no tame no chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the results of examination and promotion of measures to obtain international understanding and cooperation, and examination and development of measures to promote international exchange of technical information, conducted in the FY 1998 continuously from the previous year, with the object to realize the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project. In the FY 1998, the English version of the 1997 annual summary report was distributed to a total of about 150 overseas organizations. The WE-NET project activities were presented to the 12th World Hydrogen Energy Conference, International Joint Power Generation Conference held in 1998 by American Society of Mechanical Engineers, and 2nd International Symposium on Advanced Energy Conversion Systems and Related Technologies. For the examination and development of measures to promote international exchange of technical information, the contracting party of Japan for the Hydrogen Implementation Agreement with IEA has been shifted from the government of Japan to NEDO. NEDO has been representing Japan for various workshops on the tasks. The hydrogen projects conducted by Germany and USA were also surveyed. The WE-NET project homepage was opened in June, 1998. (NEDO)

Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on peripheral technologies around hydrogen); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

This report summarizes the fiscal 1975 research result on peripheral and seed technologies for hydrogen energy systems. Chapter 1 'Evaluation method for thermochemical techniques' reports critical study on qualitative evaluation method, estimation method for thermal efficiencies, and trial cost calculation example. Chapter 2 'Current state and problems of water electrolysis and hybrid technique composed of electrolysis and thermochemical technique' reports general survey on current water electrolysis and new technologies under development to clarify possible electrolytic voltage drop, from the practical viewpoint. Chapter 3 'Use of a high- temperature gas cooling reactor for hydrogen production' reports survey on the current and future reactors, and characteristics of such nuclear reactors, from the viewpoint that study on thermochemical technique is dependent on use of a high-temperature gas cooling reactor. Chapter 4 'Hydrogen transport and storage technology using organic compounds including oxygen' reports that acetone-isopropanol system is better for hydrogen storage. Chapter 5 'Water electrolysis using photo-semiconducting electrode' reports the additional survey. (NEDO)

Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Study on individual care in nursing home. Part 2. Studies on social welfare institution for the elderly from the aspect of dwelling; Koreisha kyoju shisetsu ni okeru kobetsuteki kaigo ni kansuru kosatsu. Sumai toshiteno tokubetsu yogo rojin home no arikata ni kansuru kenkyu 2

Energy Technology Data Exchange (ETDEWEB)

Inoue, Y.; Otaki, K.; Ohara, K. [Yokohama National Univ. (Japan)] Toyama, T. [Tohoku Univ., Sendai (Japan)

1998-06-30

This study pays attention to the relation between individual care and residents` activities in the social welfare institutions for the elderly (nursing homes) and aims to clarify the influence of building environment (nursing home as dwelling place) on individual care. Behaviors of care staffs and residents are surveyed in four nursing homes. The results of the analysis of the survey are as follows: The care staff`s activities are influenced not only by physical environment and also by the residents` activities. A single bed room is more effective than a multi-bed room for individual care. The small care unit is effective in building plan if the number of staffs is enough. The personal care activities which constitute the greater part of the care activities depend on the location of the residents. It is important to pay attention not only to arrange the common space but also how to use the common space. Spatial structure is required the consideration of the relative position of not only care rooms and resident rooms but also of care rooms and the space used by residents. 7 refs., 14 figs., 7 tabs.

Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen engine for aircraft); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kokukiyo suiso engine ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-01

This report summarizes the research results on (1) the prospect of an aviation system based on hydrogen energy, (2) the total system of aircraft based on hydrogen energy, and (3) the performance, structure and specifications of airplanes and engines using synthetic fuel such as hydrogen. In (1), study was made on air transport energy, and prediction was made on the demand of liquid hydrogen assuming conversion of petroleum fuel into hydrogen fuel in the future. In (2), the supply system of liquid hydrogen is essential in conversion of current aircraft fuel into liquid hydrogen. Such supply system over the world is also necessary in conversion into liquid hydrogen for both domestic and international airlines. In (3), in order to discuss the feasibility of liquid hydrogen fuel aircraft, the merit of such aircraft as compared with current aircraft using JP fuel, and whether designing a new airframe or modifying existing airframes, study was made conceptually on the size and capacity of airframe by statistical treatment and analysis of previous conceptual designs. (NEDO)

Studies on factors of disorder and regularity in the streeet view. Part 1. ; Studies on disorder and regularity in the central business district. Gairo keikan no ranzatsuter dot seizensei yoin ni kansuru kenkyu. 1. ; Chushin shigaichi ni okeru ranzatsuter dot seizensei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsunoto, N; Teranishi, N; Senda, M [Nagoya Institute of Technology, Nagoya (Japan). Faculty of Engineering

1991-11-30

This study intends to identify the visual confusion in spatial views by the routine human conveption of regularity and disorder, and elucidate physical factors that cause the disorder and regularity in street views. The disorder factors include the additions annexed to the view afterwards, and the regularity factors include those flat objects that decide the pattern of a view. Many factors can be either disorder or reguarity factors according to their sizes, how they look, and how they are affected by surrounding objects. The disorder in a street view is approximately determined of its degree by such distribution patterns as the spread and convergence of the disorder factors. The disorder can be intensified stronger by the spread of the factors widely over an entire area or the existence of objects that give disorderly impressions, rather than by the number of disorder factors. The regularity is affected easily by the disorder factors, it being lowered by intensities of the disorder. The deciding factors for the disorder or regularity are the kinds of objects, how they are laid out and what they are surrounded with. The factors that govern the degrees of the disorder and regularity are how large the area they are distributed in, the number, how they look, and where they are positioned. 24 refs., 9 figs., 6 tabs.

Preliminary reports on fiscal 2000 results of project for subsidizing international joint research; 2000 nendo kokusai kyodo kenkyu josei jigyo seika hokoku kai yokoshu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

This paper presents preliminary reports on fiscal 2000 results of project for subsidizing international joint research sponsored by NEDO. For international joint research teams doing excellent studies, their research expenses are subsidized, thereby promoting international research exchange, enhancing international level of industrial technology and contributing to the formation of basis for innovative industrial technology. The projects relating to the global environmental field are implemented jointly with RITE. The contents of the report to be published are, in the global environmental field (practicability study), development of oil substitute resources, reproducible resources, and technologies for producing polymeric and plastic materials benign to the earth by microorganism using carbon dioxide. In the substance/material field, the contents of the report are innovative production and device application of tunable photonic crystals using electronic penetration network; development of new synthesis process of innovative nitride, creation and theoretical calculation of electromagnetic function; studies on quantum transportation in superconductor and semiconductor bonding structures; and studies on quantum liquid and solid, and application to materials science and technology. (NEDO)

Fiscal 1997 survey report on international cooperation for the energy use rationalization method; 1997 nendo jigyo hokokusho (energy shiyo gorika shuho kokusai kyoryoku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To carry out LCA in ISO-14040, inventory analysis (IA) is the basic. For studying arrangement of public data to carry out IA, collection work was done of background data which are indirectly concerned with copying machine. First, methods to make inventory data (ID) which are thinkable in the present situation were prepared, and items of emitted matters to be collected were set up in relation to the impact assessment method. Secondly, scenarios of each stage of life cycle of copying machine were set up, and virtual data on the material/energy consumption amount were arranged. Based on this, a method was further studied for making ID of the parts used in electric power, iron/steel, plastics, and copying machine. Third, based on the above-mentioned study results, ID was actually made, and a possibility was studied of making inventory in life cycle of copying machine. Moreover, the state of the automobile LCA carried out at Stuttgart University was examined. At last, the paper summed up subjects of and future study methods for the inventory making method. 2 refs., 25 figs., 77 tabs.

Report on an international joint research project for global environment technology in fiscal 1998; 1998 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to serve for measures against global problems taken by Japan, joint research was carried out with overseas research organizations. The research project selected ten themes considering urgency, internationality and economic proliferation effect in areas to serve for solution of global environment problems. These themes include removal or emission control of greenhouse effect gases, measures against atmospheric environment problems such as acid rains and ozone layer destruction, prevention of ocean contamination, development and effective utilization of energies and resources. When the feedback of these themes to the NEDO projects is considered, the research achievements in relation with development of the acid rain monitoring system in particular support indirectly development of carbon dioxide fixation technologies. The research achievements in developing an environmentally friendly biomass energy manufacturing process and environmental effect evaluation thereon contribute as an effective process to carbon dioxide reduction using biomass as raw materials. The achievements in research of nonlinear interfacial properties and mixed phase turbulence of low-purity carbon dioxide bubbles contribute to a project related to storage of carbon dioxide in oceans. (NEDO)

Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

Survey of pollution-resistant plants and their cultivating techniques; Osen busshitsu taisei shokubutsu to sono shokusai gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The reduction of forests due to environmental pollution has been surveyed, to investigate the pollution-resistant plants and solid microorganisms. In Japan, the blight of needle-leaf trees (pine and momi fir) and of Japanese oak has occurred, and blight of some other trees, such as wild cherry trees, Japanese apricot trees, birch, Japanese cedar, cypress and bamboo, has been reported from various regions. In this article, plants reported to be resistant to pollutants are listed, and the physiological features of these plants are described. Furthermore, to develop pollution-resistant plants, reports relating to clarification of the mechanism of resistance development and the genes involved are reviewed. Microorganisms which symbioses for roots support these root functions. They also suppress the activity of pathogenic microorganisms and improve the environment around the roots, thus helping plants to grow normally. The roles played by symbiotic microorganisms and how to utilize these organisms are discussed. Their functions in coping with acid rain and heavy metal pollution, and how to utilize such functions are also discussed. 707 refs., 13 figs., 13 tabs.

Study on the cutting behavior of plasma sprayed ceramic coatings. Plasma yosha ceramics himaku no sessaku kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Inui, Y; Kubohori, T; Ikuta, T [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1992-09-30

Fracture behavior of Al2O3-TiO2 sprayed ceramic coating was investigated at low cutting speeds when using two dimensional cutting. Scanning electron microscope was used to observe the generation, development and propagation of cracks during cutting. Small cracks and fracture have been developed in the cutting groove along the cutting direction, and there has been many fractures in spray particles unit. In the initial stage of cutting, radiant cracks have developed on the sprayed coating, however, linear big cracks starting from the cutting edge towards the cutting direction, have developed. The cracks have developed along the grain boundary of coating component, and cracks progressed along the portion with weak bonding force. When the depth of the cut was under 5[mu]m, the cutting face has formed many microfractures, and the cutting has been very stable. It has been necessary to select the cutting conditions that do not cause big fracture, microcutting and so on, in order to achieve favorable surface condition with minor fractures. 8 refs., 13 figs., 2 tabs.

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

Performance analysis on natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no simulation ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1997-11-25

Outlined herein are a procedure developed to simulate performance of an energy-autonomous (independent) solar house referred to as HARBEMAN HOUSE (HH) built in 1996 in City of Sendai, comparison between the simulated and observed results, and characteristics of the solar house. The house is equipped with a solar collector and sky radiator, both installed on the roof, the former facing south to collect solar energy and generate hot water whereas the latter facing north to radiate heat and generate cool water. Both are connected to an underground heat-insulated tank having a capacity of 31m{sup 3}, which stores hot or cool water to keep their conditions for extended periods. The solar system operates in heat- or cool-storage mode. In the heat-storage mode, quantity of heat stored increases, although at a slow rate, as tank capacity increases. In the cool-storage mode, on the other hand, quantity of cool stored increases in proportion to tank capacity. This is because solar energy is collected throughout the year whereas cooling by radiation is concentrated in early spring. Loss rate of heat stored increases as tank capacity increases, and the opposite trend is observed with cool stored. 12 refs., 7 figs., 2 tabs.

Study on the effect of micro-gravity on bio-functions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The effect of micro-gravity on bio-functions and vital reaction was studied using the facility of Underground Gravity-free Experiment Center Co. On the effect on osteoblast shape and gene expression, although fluorochrome reacting with Ca was well taken into cells, no significant difference in Ca content in cells was observed before/after falling. Expression of genes related to cell propagation was controlled under micro-gravity. Protoplast fusion of Lentinus was unaffected by micro-gravity. The mRNA fragments of gravity sensitive mutant of rice plant were affected by micro-gravity. Paramecium was set swimming in solutions with different specific gravities. The reaction behavior of Paramecium was affected by the difference in specific gravity between cell bodies and solutions. The water content metabolism functions of a mouse with needle stimulus, in particular excretory, were slightly promoted by micro- gravity. The cortisol level in blood of a falling mouse group rose showing strong stress. As the preliminary study on the geotaxis of insects, motion of bagworm was observed. 12 refs., 38 figs., 4 tabs.

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by Optoelectronic Industry and Technology Development Association as part of the cooperation programs, for establishing the Asian environmental information networks. It outlines the research cooperation project for the environmental networks, results of the 4 on-the-spot surveys, 2 occasions for inviting researchers to Japan, and construction of the internet and Asian environmental information network systems. (NEDO)

Outline and summary of research for a database of unused energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For effective promotion of the new energy utilization project of NEDO and preparation of the future new energy vision, the data on unused energy were systematically arranged. The definition of heat supply systems using unused energy was clarified, and the kind and property of unused energy were arranged. Some typical systems of heat supply facilities using unused energy were presented. The data were classified by energy source, temperature level and region, and the detailed database was prepared for the typical systems. The overseas database was prepared, in particular, for European and American systems. Domestic and overseas policies, laws and subsidy systems were arranged. The introduction effect of two heat supply facilities using unused energy was surveyed, and their operation costs were analyzed. Basic terminology related to unused energy was compiled and explained. Related organizations, in particular, manufacturers were surveyed and arranged. The main manufacturers of a heat recovery refrigerator and waste heat boiler as typical equipment, and the number of these equipment shipped were arranged. 51 figs., 116 tabs.

FY1995 study of feedback type gait training system; 1995 nendo feedback gata hoko kuren sochi ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this project is to develop and demonstrate the utility of feedback type gait training equipment designed for the measurement and evaluation by a walking training of the aged or patient. As similar concepts of walking training, a locomotion in the water for the aged is applied in rehabilitation. Our development of this study established the system of a suspending mechanism which revolves around the prop, and a walking on the circular type force plate by the aged or patient. It is possible to detect a walking reaction force of several patients from force plate simultaneously. And then, the data from force plate makes feedback signal to put up the patient like a buoyancy in the water. Concerning the evaluations of walking pattern a step range, a hanging ratio and a walking speed, etc. are acquired for each patient by the acknowledgment base. This system is actively able to perform a walking training continuously compared with conventional passive gait equipment. (NEDO)

Research on crystal growth by using pressure as a control parameter; Atsuryoku seigyo ni yoru kessho seicho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

This research project aims to establish a technique for crystal growth using pressure as a principal control parameter, and combining it with a microgravity condition, to develop a novel process material fabrication. Since the solubility of materials depends on pressure, it is possible to control a supersaturated condition for crystal growth by changing pressure. The growth condition can be controlled precisely, which is not possible by conventional methods that vary temperature and other factors. On the other hand, because a concentration diffusing field is formed autonomically around crystals in association with their growth, density convection is generated under gravity as a result of difference in the concentrations, making the growth conditions severely complex and uncontrollable. Ideal crystal growth condition control may be possible if the pressure control is performed under micro-gravity by which generation of the density convection can be suppressed. Realization has been achieved on in-situ observation by using high-magnification microscope which uses a diamond anvil cell, development of a hydraulic type optic pressure cell, and a high- speed crystal growing technology by means of pressure control utilizing the cell. New findings were also obtained on effects of pressure on crystal forms, and the pressure induced solid phase transfer mechanism. 67 refs., 49 figs., 3 tabs.

Demonstrative study for the wind and solar hybrid power system. 2; Furyoku taiyoko hybrid hatsuden system ni kansuru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kimura, Y; Sakuma, H; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1996-10-27

In order to verify the complementary relationship between wind and solar energy, the long-term field test of the hybrid power system was conducted at the natural energy square of Ashikaga Institute of Technology. The solar cell blade windmill composed of a Savonius windmill and flexible solar cells applied to swept buckets was also prepared. As a result, the wind power generation was promising mainly in the winter period including the late fall and early spring, while solar one was stable all the year through although it was slightly poor in winter. Stable power generation was thus achieved by combining wind energy with solar energy. As the whole data of other wind and solar power generation systems at the square were analyzed for every month, the same conclusion as the solar cell blade windmill was obtained as follows: the wind power generation in Ashikaga area is promising in Nov.-March from the field test result for 16 months, solar power generation is stable all the year through, the hybrid power system is effective in Nov.-April, and the solar cell blade windmill is equivalent to the hybrid power system. 3 refs., 5 figs.

Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

Study on visibility evaluation model which is considered field factors; Field factor wo koryoshita shininsei hyoka model ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakanishi, M; Hagiwara, T [Hokkaido University, Sapporo (Japan)

1997-10-01

The present study proposes a model to evaluate visual performance of road traffic facilities required for drivers. Two factors were employed to obtain the suitable contrast for drivers under driving situation. One factor is a suitable luminance range, which is derived from minimum required luminance and glare luminance. Another is a field. The model showed capability of providing visibility range in some cases. 8 refs., 4 figs., 2 tabs.

Ultimate strength analysis of long-span cable-stayed bridges; Chodai chachokyo no shukyoku kyodo kaiseki to kyodo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Xie, X.; Yamaguchi, H. [Saitama Univ., Urawa (Japan)] Nagai, M. [Nagaoka Technical Coll., Niigata (Japan)

1998-07-21

Recently, span of cable-stayed bridges has been getting loner and longer, present situation is that cable-stayed bridges with span 600 to 800m class have been built inside and outside the country, and accurate determination of its ultimate strength has been an important problem statistically. However, concrete design method for evaluating load bearing stress of long-span cable-stayed bridge. Particularly of the main beam whose axial stress is dominating, has not been established so far. As for cable-stayed bridge, even for long-span, effect of plasticization of cross section on ultimate strength is severe because there is little effect of geometric nonlinearity and it is thought that accurate evaluation of ultimate strength only by elastic finite potential analysis is difficult. Accordingly, it is necessary to study the behavior by using combined nonlinear analysis considering the nonlinearity of the material in order to evaluate the safety and economy to long-span cable-stayed bridge. In this report, 3 dimensional analysis method was formularized taking into account the combine nonlinearity of multi-box girder and analysis program of ultimate strength behavior of long-span cable-stayed bridge was developed. 19 refs., 17 figs., 2 tabs.

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (power generation No.15). Achievement report on development of guided boring system for buried power network; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.15). Denryokumo chichuka hikaisaku kanro kensetsu koho no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

What impedes the popularization of the guided boring system is the functional insufficiency of the drilling position measuring method. For the purpose of properly dealing with the situation, efforts are made to develop a new drilling position measuring method which is highly reliable even when there exist previously buried pipes or electromagnetic noise. Activities are conducted in the two sections of (1) the study of an drilling position measuring method not to be easily affected by magnetic noise and (2) the study of a method for detecting previously buried objects. In section (1), based on the technology of a drilling position measuring system (locator) which is currently the most popular among horizontal drilling systems, a signal processing technology capable of reducing the effect of noise and a new position measuring method are contrived, and it is proved by the use of an experimenting system that they work effectively. In section (2), with attention paid to the small horizontal drilling device, an underground radar technology with the radar probing into the ground from the ground surface or from a drilling head is studied as an effective and easy-to-use method for detecting previously buried steel pipes. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Energy conservation No.4). Development of passive cooling mechanism fit for high-temperature high-humidity region; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (Shoe No.4). Koon tashitsu chiiki tekigogata passive reikyaku kiko no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made in cooperation with Vietnam to develop a heat insulating material for buildings, to be used for passive cooling mechanisms symbiotic with the environment and capable of energy conservation. Vegetables are planted on the surface of this building material. Activities are conducted in the three domains of (1) the development of energy conservation-conscious basic materials, (2) selection of vegetables, and (3) the simulation of the effect of the developed materials on temperature. The basic type of the newly developed building material is an asbestos-free vegetable fiber-reinforced cement slate which is covered by such vegetables as members of the Passifloraceae, Vitaceae, and Araliaceae. Conducted in domain (1) are surveys of the actual state of basic material manufacturing in Vietnam and studies of the basic properties of vegetable fiber, properties displayed by vegetable fiber under various chemical environments, selection of vegetable fiber as the basic aggregate, mineral fiber, and the basic material manufacturing conditions. The result of heat load calculation carried out using SMASH for Windows ver.2, which is a program developed for thermal load calculation for houses, shows that the new material lowers the temperature by approximately 3 degrees C. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on automobile engine); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-10

The paper made an investigational study of the data of a wide range which seems to be related to the use of hydrogen as automobile use fuel. The advantage is that the exhaust can almost be non-pollutant. The engine performance can be on the same level as that of the present gasoline engine or can be improved. The reasons are that the compression rate is heightened and that automobile can be driven at lean mixture rate. As to weak points, the volume and weight increase when it is loaded on vehicle. The cost of hydrogen is higher than that of petroleum. The problems to be quickly solved are as follows. Improvement of the combustion method: a wide range of development not only the electric ignition method, but the diesel method, and the basic study for it. It is necessary to establish the basis for a method to connect the storage method and engine. It is also necessary to comprehensively review rules related to safety. For the future, the conversion to artificial fuel is indispensable, and hydrogen has the most characteristics as energy medium. The problem is much larger sizes of fuel tank and pump, but there will be a possibility of producing a new technology together with the hydrogen production technology. The fundamental research should be promoted without any hesitation. (translated by NEDO)

Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

Study on internal flow near the impeller outlet of a winnowing fan. 2nd Report. Discussion of a impeller with forward-inclined blades by computational fluid dynamics; Karami fan no haneguruma deguchibu kinbo no nagare ni kansuru kenkyu. 2. CFD wo mochiita maemuki hane ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kawase, M. [Tokushima University, Tokushima (Japan); Fukutomi, J.; Nakase, Y. [Tokushima University, Tokushima (Japan). Faculty of Engineering

2000-03-25

Because of a strong 3-dimensional flow, it is difficult to produce a uniform flow or improve efficiency with winnowing fans. Through experiments with various types of impellers, it was found in an earlier study that a forward-inclined impeller could produce a uniform flow and improve efficiency. It was ten reported in a subsequent study aimed at identifying the mechanism behind this, in which the relationship between velocity and static pressure in an impeller of small inclination angle was examined from the perspective of flow, that flow analysis was effective towards estimating inconsistent flow characteristics. Based on these findings, this project was designed to measure and analyze flow characteristics in a forward-inclined impeller. It was found that forward-inclined impellers have many regions of circulating flow and that the mainstream which moves to the outlet is narrow in effective area. As a result, velocity increases and discharge blow rapidly expands within a short distance. Therefore, good static pressure recovery is obtained. (author)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

Fiscal 2000 report of investigation. International cooperative investigation on method for rationalizing use of energy; 2000 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigative research was conducted for the purpose of building a database for LCA (life cycle assessment) that will be commonly used in Asian countries and developing an applicable environmental assessment methodology, with the fiscal 2000 results compiled. This year, joint researches and investigations were carried out with four countries, namely, Konkuk University (Korea), Taiwan Environmental Management Association (Taiwan), Universiti Putra Malaysia (Malaysia), and Thailand Environmental Institute (Thailand). The investigation covered the status how LCA problems were dealt with and how LCA infrastructures were built in the four countries. In the construction of the database for LCA, methods of preparing the LCA inventory database and their results were investigated concerning electrical power systems and production of basic materials (steel products), which were most important in implementing LCA in particular. In Thailand and Malaysia, lack of data for LCA was presumed; hence, necessary data sources were examined. Further, investigated also were the state of importing subterranean resources such as coal, oil, natural gas and iron ore, and the resource material flow or the like in each country. (NEDO)

Project to promote the technical development of global environmental industries. International research exchange project; Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Exchanges with researchers/research institutes in overseas countries have an important meaning in promoting the research and development toward the creation of new research fields where the solution to the environmental problem is aimed at and toward the construction of new technological systems. Therefore, under the cooperation of Research Institute of Innovative Technology for the Earth (RITE), and RITE related researchers and societies, given were invitation and dispatch of researchers to international conferences and symposia involved in the global environment related technology, and exchanges with major overseas research institutes/universities. At the same time, based on the short-term invitation and dispatch so far given, a system was established for medium- and long-term dispatch/invitation of researchers who are thought to hold an important position in the future research activities. From the results obtained, domestic and foreign exchanges relating to the latest research could be promoted. In addition, researches in the basic domain related to the global environmental technology were advanced in a variety of fields overseas. The numbers of invitation and dispatch given in fiscal 1995 were 12 and 13, respectively, the results of which were included in this paper. 121 refs., 74 figs., 11 tabs.

Report for fiscal 1998 on the international joint research project of medical welfare equipment; Iryo fukushi kiki kokusai kyodo kenkyu jigyo 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In connection with the international joint research project of medical welfare, a report was made on the results of the investigation conducted in 1998 concerning the technology of overseas medical welfare equipment. In the investigation of china, observation was made on the actual state of the representative medial institutions, with opinions exchanged. Obsolete equipment and old technology are the present state in China, which is strongly desirous of exchanging information with Japan. In Taiwan, being full of venture spirit, an ultrasonic thermal treatment apparatus and an ultrasonic echo device have been produced for example. In Europe, an observation tour was conducted on a German manipulator and process robot while an investigative visit and exchange of opinions were made on the living environment and facilities in Italian training center for physically handicapped persons. Japan's self-supporting and assisting system for excretion attracted many questions and comments. In the investigation in the U.S., views were exchanged concerning '{sup 13}C-MRS device for non-invasion brain metabolic measurement' in research institutions such as universities. A machine developed in Japan received a high evaluation in that {sup 13}C spectrum was obtained from a substantial depth. (NEDO)

FY 2000 survey report on possibilities of the international joint study in the Asian region; 2000 nendo Asia chiiki kokusai kyodo kenkyu kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was conducted of policies on energy spread, trends of energy development, etc. in energy conservation and substitution energy fields after the economic crisis in Asian countries, and the results were summed up. In Thailand, it is expected that the effective use of solar energy can be an effective means as a substitution energy. Further, the energy conservation by demand-side management, etc. is to be urgently taken. Indonesia is abundant in energy resources and does not take energy conservation measures very much. As to petroleum substituting energy, it is expected that the diversified use of coal, natural gas, hydroelectric power, geothermal energy, etc. will be advanced. In Malaysia, a policy in which energy is dispersed to natural gas, hydroelectric power and coal is being taken for reduction of the dependence upon petroleum. In India, joint projects with developed countries are proceeded with in the fields of electric power, energy conservation and renewable energy. In China, the policy for advancing new energy utilization is being taken that the thermal power generation is optimized, hydroelectric power generation is positively adopted, and nuclear power generation is moderately used, according to characteristics in the region. (NEDO)

Effect of ventilated structure on dehumidification. ; Experimental result in winter. Tsuki koho no haishitsu koka ni kansuru kenkyu. ; Toki jikken kekka

Energy Technology Data Exchange (ETDEWEB)

Sugai, T; Ozaki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering; Katayama, T; Hayashi, T; Shiotsuki, Y [Kyushu University, Fukuoka (Japan)

1912-09-01

Temperature and humidity characteristics and condensation within walls under heating and humidification were studied experimentally in winter using two test houses of conventional and ventilated structures. The absolute humidity in conventional one fluctuated depending on temperature gradient, water flux due to humidification and water adsorption onto glass wool, and accumulated water increased with humidification. That in ventilated one was also affected by dehumidification through ventilation layers. Under heating and humidification, the absolute humidity increased depending on temperature rise and water flux within walls. In conventional one, condensation was frequently observed on felt in walls and others because of accumulated humidity, while in ventilated one, humidity was kept lower within walls even under heating, because humidity in walls was discharged through ventilation layers. Condensation was also scarcely observed on waterproof moisture-permeable sheets in walls and others. 3 refs ., 39 figs 1., tab.

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-10-01

For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

Study on hydrogen storage alloy for NiMH EV battery; EV yo NiMH denchi no suiso kyuzogokin ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kanemoto, M.; Tanaka, T.; Furukawa, K.; Watada, M.; Oshitani, M. [Yuasa Corp., Osaka (Japan)

1998-10-30

We have developed a high performance hydrogen storage alloy (MH alloy) suited to NiMH batteries for EV use. During the course of the development, the effects of alloy composition and structure (B/A ratio in AB{sub 5}) on cycle life and high-rate discharge of MH electrodes were investigated using mainly SEM, XRD, TEM analysis. It was found that Co content and B/A ratio (5.1/5) of MH alloy have significant effects on corrosion resistance and high-rate discharge at low temperature. Further, the surface treatments of MH alloy with weak acids and hydrophobic agents were effective for improving the initial activation and for depressing the cell internal pressure build-up. (author)

Investigational research on CO2 isolation technology in fiscal 1995; 1995 nendo nisanka tanso no kakuri gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper studied present technical subjects and future study subjects of the CO2 isolation technology in order to clarify technical and social problems and the developmental subjects of the CO2 isolation technology and related technologies for separating/concentrating CO2 emitted in relation to quantity consumption of fossil fuel and storing it in ocean or underground. Main items for the study were: (1) investigational study of the technology of CO2 ocean storage, (2) investigational study of environmental effect assessment in storing CO2 in ocean, (3) investigational study of the technology of CO2 ocean storage, etc. Technologies required for the ocean isolation were arranged such as CO2 storage, injection, dispersion technique, CO2 behavior simulation, and the developmental subjects were extracted. Further, in the deep-sea bottom storage method, a simulation to calculate the range of PH effects was conducted presuming the specified amount of CO2 and applying known physical values, and evaluation of the CO2 ocean discharge/solution method was made. A method was also studied for experiments on water bacteria and benthos. 127 refs., 102 figs., 81 tabs.

Studies on reducing the thermal loads of solar-pumped solid state lasers; Taiyoko reiki laser no netsufuka teigen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimizu, K; Yugami, H; Naito, H; Arashi, H [Tohoku University, Sendai (Japan)

1997-11-25

It was intended to reduce the thermal loads of solar-pumped solid state lasers (highly densified solar light is irradiated directly onto a laser medium to cause excitation. No electric power is required for the excitation.). For this purpose, experiments were performed by using a selective permeation film. Solar light includes wavelengths not effective for excitation, which causes heat generation and thermal loads such as lens heating effect and thermal stress compounded refraction, degrading the laser beam quality. The Nd:YAG was used as a laser medium, and a multi-layered film (composed of SiO2 and TiO2) which cuts wavelength below 500 nm as a selective permeation film to cut light having wavelengths not required for excitation. A laser transmitting experiment revealed that the slope efficiency is improved by 27% as compared to not using the film. Beam fluctuation was improved to 45%. Using the selective permeation film has realized more efficient conversion of the solar light into a beam with better quality. The results for calculation of heat lens effect by using temperature distribution simulation showed good agreement with experimental values. Using the selective permeation film can suppress the maximum temperature of a laser rod to 68%, as well as the thermal stress. 9 figs., 2 tabs.

Improved design of three-dimensional lens for low concentrator PV modules; Teishukogata taiyo denchiyo sanjigen lens no koseinoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Goma, S; Yoshioka, K; Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan)

1997-11-25

Attention is paid to reduction in area required for solar cells by solar concentration as a means of solving cost limits of solar cells and unstable supply of Si materials. Low concentration solar cells are effective from the aspects of utilization of scattered light and unnecessary ray tracing. The optical concentration ratio was calculated of three-dimensional lens having design values of various north/south and east/west direction allowable incidence half angles. The three-dimensional lens are designed by cutting a rectangular parallelepiped by the two-dimensional composite elliptical plane designed by various allowable incidence half angles from two directions of north/south and east/west. Using Perez`s sky solar radiation models and meteorological data HASP, calculated were the annual accumulated global radiation ratio on an inclined surface and the optical efficiency. Calculated were the solar cell area ratio and solar concentration area ratio of the concentration type to obtain solar radiation the same as that of the planar type. From the optimization calculation, it was found that lens are optimal which have design values of north/south and east/west direction allowable incidence half angles of 30-70deg. The solar cell area ratio is 57% and the solar concentration area ratio is 1.2 times. It was found that by making the module area 1.2 times, more than 40% of the solar cells used can be saved. 5 refs., 8 figs.

Study on recent research trends in the chemical fields; Kagaku bun`ya ni okeru saikin no kenkyu doko ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This research is conducted to search study themes of chemistry expected towards the 21st century. The complex compound in the fundamental chemistry field and the bio-medical materials in the applied chemistry field are taken up. Bio-medical materials are used for the restoration, rehabilitation, and treatment of the organ and the improvement of its functions. For implants such as hearts, anti-thrombin and anti-calcium precipitation effects and high endurance are required. In this field, special copolymers and bio-membrane-emulating surfaces are studied. For artificial organs, hybrid type materials combining cells, and physiologically active and artificial materials are also studied. There are studies on the missile therapy of drugs and DDS (drug delivery system). The complex compounds contain metallic elements, such as Fe, Mn, Co and Cu, and groups known as ligands which combine these metal elements. They can have a variety of stereo-structures and physical properties. They also exhibit a diversity of functions including electron donor bonding, molecular recognition, chemical substitution, and pharmaceutical activity. These features open up a promising potential for their prospective use as physiologically active substances, cancerostats, new materials, artificial photosynthesis, memory elements, and complex catalysts. 88 refs., 35 figs., 6 tabs.

Investigational study of optical function materials for two-dimensional data processing; Nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper investigated/studied `space light modulation materials,` `dynamic hologram/memory materials,` `optical waveguide path materials,` etc. which become key materials in the high speed two dimensional processing. As to electrooptical materials proposed in this investigational study, the external electric field and the electric charges generated make quality of molecules themselves directly change to memory strong/weak signals of light. Therefore, the response velocity becomes less than a millionth of that of the liquid crystal display, and high speed which is needed for realtime moving image processing is anticipated. Hologram includes the phase information in addition to information on light strength. Therefore, it is a large capacity record medium and at the same time a record medium which can read/write two dimensional information as it is. With optical fiber, images cannot be transmitted as they are. Light waveguide path materials are those that accumulate roles of mirror and lens in a sheet of the material and construct a system which is strong in vibration, as optical parts connecting among materials for two dimensional data processing. 273 refs., 107 figs., 17 tabs.

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-05-01

The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

Trend of research on future development of new biocatalysts. 2; Shinki bio shokubai no sosei ni kansuru kenkyu doko chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Creation of new biocatalysts was surveyed to convert chemical reactions into environment-friendly processes. Biocatalysts are characterized by their high catalytic activity, uniqueness of reactions, and non-pollution under mild conditions. Stability is required for them, such as heat resistance, solvent resistance, acid resistance and alkali resistance, under severe conditions. For the development of new biocatalysts, it is necessary to multiply utilize the techniques containing enzymes, ribozymes, mold synthetic polymers, chemical modification, and non-natural proteins. Natural enzymes have been conventionally improved through the search, imitation and modification. Hereafter, new biocatalysts with functions required for the reactions should be created by integrating information regarding functions, structures and activation of these enzymes. It is indispensable to cooperate closely with supporting techniques, such as gene engineering, organic synthesis, biophysics and computer chemistry. 35 refs., 26 figs., 1 tab.

Study on the impact assessment for the life cycle assessment (LCA); Kankyo fuka bunseki ni okeru impact assessment ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes the impact assessment which is an important step for LCA. For classification of the impact assessment, the existing literature was reviewed and a skeleton for the classification was proposed. The weighting factors for nine selected impact categories, which were used to calculate environmental load point (ELP) for the valuation, were obtained for two overseas groups, i.e., students of Amsterdam University and SETAC Europe members. It was found that the former provided the similar trends to general Japanese, however that the latter gave high weighting in the global warming and depletion of ozone layer. The ELP was proposed and applied to automatic washing machine, coffee maker, waste incineration power generation system, and co-generation system. As a result, its effectiveness was demonstrated. This report also describes problems for the LCA of thermal and material recycling of PS trays. 99 refs., 96 figs., 73 tabs.

Survey on a possibility of geothermal utilization in Tomakomai City; 1980 nendo Tomakomaishi ni okeru chinetsu riyo kanosei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-11-01

This paper describes a possibility of geothermal utilization in Tomakomai City. The Tomakomai area has an extremely great amount of hot water existing in deep layers, leading to a consideration that it is very highly possible to develop the hot water. As seen from the underground structure and ground temperature gradient in the Tomakomai sedimentary basin, the development depth would be considerably great, being assumed to be about 2,000 meters. The acquisition amount per well is estimated 100 m{sup 3}/hour or more at 65 degrees C. Rise in petroleum price in the future is an unavoidable fate, hence geothermal water utilization has a fully bright future. The water has relatively low temperature, and is effective for use in room heating, hot water supply, and agricultural and livestock industries. It is worth considering utilization as a local energy system. It has also large secondary effects. According to the latest trial calculation, the unit price for hot water for room heating and hot water supply would be 10 to 20 yen per 1,000 kilo-calories. If the same amount of hot water should be supplied from a boiler, fossil fuel of 20,470 kl/year would be required. If converted by using a kerosene price of 75 yen per liter, the cost would be 1.3 billion 35 million yen, comparatively higher than the geothermal water utilization. (NEDO)

Research cooperation project on conservation and sustainable use of tropical bioresources; Seibutsu tayosei hozen to jizokuteki riyonado ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research cooperation has been conducted on the conservation of biological species inhabiting in the tropical rainforest in developing countries in tropic zone and the sustainable use of genetic resources using biotechnologies. For the research cooperation with Thailand in FY 1996, research of the food acquisition strategy of the Primates has been conducted. A total of 19 species of animals and plants, i.e., 7 species of arbors, 7 species of herbs, and 5 species of insects, were newly confirmed for pig-tailed monkey. In Indonesia, a feasibility study was conducted on the information center of Indonesian tropical bioresources. For the research of culture collection of bacteria, 113 strains of acetic acid bacteria and 85 strains of lactic acid bacteria were separated from Indonesian specimens, and they were identified. An agreement was concluded with Malaysia, and discussions were conducted for the concrete implementation plan. For the project, construction of a database was investigated for bioresources including bacteria and higher animals useful for industries. Maintenance of gene bank was also investigated. 391 refs., 61 figs., 93 tabs.

Report on investigations and studies on chemical conversion of photo-energy; Hikari energy no kagakuteki henkan ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper summarizes problems in utilization of solar energy, their solutions, features, the currently achieved results, and prospects. With regard to water decomposition using semiconductors, simultaneous generation of hydrogen and oxygen has already been achieved, and there is high possibility of raising the efficiency by improving catalysts. Water decomposition using metal complexes has acceleration of charge isolation as the largest problem, whose prospect of solution is not necessarily bright at the present time. Photo-catalytic reaction is a field to be discussed as one means of developing a new synthesizing method from the viewpoint of organic synthetic chemistry. Conversion into electric energy that uses a photovoltaic process has high efficiency, and is a field to be noted. In photo-energy conversion by means of photo-synthesis, living organisms performing hydrogen production at high efficiency have been discovered. Important studies include the studies in terms of chemical engineering using these living organisms, improvement of breeds by gene manipulations, and studies that utilize living organisms or part of the constituting components. (NEDO)

Study on the estimation method of maneuvering hydrodynamic force in turning motion; Senkai undoji no soju ryutairyoku suiteiho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kijima, K; Yukawa, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Maekawa, K [Hokkaido University, Sapporo (Japan). Faculty of Fisheries

1996-04-10

Estimation of the maneuvering performance of ships is very important from the viewpoint of safe navigation. Using three types of VLCCs (SR221A, B, C) with locally different stern frame lines as computational models, the estimation method of hull hydrodynamic force in turning motion was studied theoretically taking frame line shapes into account. The unstable behavior of courses was also studied using linear differential coefficients obtained from the estimation result on hull hydrodynamic force in oblique navigation and turning motion. As a result, the estimation result on hull hydrodynamic force was slightly different quantitatively from model test results in a range of large drift angle or turning angular velocity, while that was relatively well agreed with test results in a range of small such angle and velocity. As the study result on the unstable behavior of courses by using linear differential coefficients obtained from the estimation result on hull hydrodynamic force, determination of a course stability was possible by considering local difference in hull shape. 4 refs., 8 figs., 1 tab.

Survey on weather changes associated with large-scale tree-planting. 2; Daikibo ryokuka ni tomonau kiko henka ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

An investigational study was made for large-scale tree-planting aiming at CO2 fixation. Water resource and precipitation relating to tree-planting were determined from NASA data and arranged into the global distribution map. It was found that Australia and the Chinese continent are under the relatively favorable condition. As for the soil condition, nutrition resource is short in the desert and unused zone. From the vegetation data obtained from meteorological satellite NOAA, developed was a method for estimating net primary productivity of terrestrial ecosystem and obtained was a global distribution map for the amount of CO2 fixed under the present terrestrial vegetation. At the same time, areas which have great potentiality of tree-planting were selected from the map for estimating potentiality of the global tree-planting. To study the promotion of rainfall as a means of expanding the potential tree-planting area, the conventional meteorological and physical model was improved, and more realistic simulation was made possible. Also as to the water utilization technology, the modeling method was developed. As the area having a potentiality of expanding tree-planting, Australia (especially the west) was cited as the first candidate, and China the second candidate. 108 refs., 128 figs., 49 tabs.

Study on a technology to afforest water level varying part of a reservoir; Chosuichi suii hendobu ryokuka gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onodera, O.; Matsubara, K.; Koyama, S. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1999-03-19

Equisetum was noted as a plant adaptable to stringent environment referred to as the water level varying part of a reservoir, and was used for afforestation trials. The afforestation trials were performed at the reservoir of Uryuu Dam No. 1 and the regulating reservoir of Moiwa Dam of Hokkaido Electric Power Company. Although the rate of water level variation is small at Uryuu Dam No. 1, it is necessary for Equisetum to withstand submergence and drought for an extended period of time. Moiwa Dam has high water level variation rate, but its water depth is small, and the reservoir is free of long-term submergence and drought. As a result of long-term observation from 1993 through 1997, Equisetum was found having grown well at lower altitude part with higher submergence frequency. It has grown favorably even in parts where submergence rate reaches about 80%. However, at higher altitude with submergence rate of 10% or lower, decrement trend was seen. At Moiwa Dam, Equisetum was all buried in accumulated sand and earth, revealing that such an environment is unsuitable for Equisetum as the one subject to effect of sand and earth that flow in during freshet. (NEDO)

Research cooperation of the development of laser radar for environmental measurements; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research and development of the laser radar for measuring the air pollution in urban areas and the environmental information network have been conducted through the cooperation with Indonesian researchers. A measurement system suitable to actual situation of Indonesia has been constructed. In FY 1996, some works have been conducted as in the final fiscal year. To set the laser radar for environmental measurements and to make a plan of measurement research, conditions of air pollution in Indonesia and setting places of systems have been investigated. Opinions for the cooperation research have been exchanged with Indonesian researchers. Actual trends of the environmental measurements technology using laser radar have been surveyed. Indonesian researchers have been invited to learn operation and data processing of the system. One unit of MIE diffusion laser radar system has been designed and fabricated, and an additional data processing program has been made. The system has been delivered to Jakarta and installed. After the adjustment, performance tests have been conducted to complete the construction of the system. 3 refs., 72 figs., 10 tabs.

Research on giving antibacteria activity of tailored dental materials; Gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The secondary dental caries easily occur by breeding of bacteria in cavities between living body and composite resin, false tooth or root of tailored tooth as tooth repairing materials. The antibacteria activity of tailored dental materials was thus studied by implanting Ag ion. The antibacteria effect with time after culture of caries bacteria was studied by implanting Ag ion into SiO2 powder, PMMA samples and Ti alloy samples at 20 and 200keV in energy of ion. In addition, the antibacteria activity of SiO2 powder as composite material was found at 25keV which was previously effective for the antibacteria activity. This SiO2 filler (Ag{sup +} filler) showed the antibacteria activity on every bacteria sample after 2h, and in particular, could kill all of 3 kinds of bacteria obtained from a composite resin surface after 12h. The number of living S. salivarius was reduced by half after 12h. The application of the composite resin filler implanted with Ag{sup +} is significant to prevent recurrence of caries. 5 refs., 27 figs., 7 tabs.

Evaluation of damping property of long-span prestressed concrete cable-stayed bridges; Chodai PC shachokyo no gensui tokusei ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Yamanobe, S.; Niihara, Y.; Minami, H.; Kono, T. [Kajima Corp., Tokyo (Japan)

1999-09-30

As to the dynamic design in the antiseismic design of PC cable-stayed bridges, evaluation of damping is important. Since it is difficult to evaluate damping property theoretically and analytically, a lot of studies have not been made about how to set up damping coefficients. In this study, using analytical models of existing long-span PC cable-stayed bridges, to clarify causes of damping of long-span PC cable-stayed bridge, the rate of strain energy in each member was examined. Equivalent damping coefficients of each member, effects of friction in movable bearing, and effects of basically radiational damping were studied. The correspondence with the results of the vibration experiments conventionally made were studied. (translated by NEDO)

Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.18). Achievement report on development of device for monitoring biomass decomposing enzyme gene expression; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.18). Biomass bunkai koso idenshi hatsugen monitoring device no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A fuel production system is under development to supply fuel for power generation, in which biomass is efficiently fermented. In this connection, based on biomass decomposing enzyme related gene information provided by Japan and the U.S., a DNA (deoxyribonucleic acid) chip is built, wherein biomass decomposing enzymes, control factors, and enzyme secretion enhancing genes are densely deposited. Efforts are made, using the chip for the monitoring of the enzyme production process during the culture of mold, to develop technologies for collecting information simultaneously and comprehensively concerning the expression of great numbers of biomass decomposing enzyme genes and concerning other genes that control the production or enhance the secretion of enzymes. In concrete terms, approximately 2000 types of genes are selected out of the Aspergillus EST database held by the Japanese and U.S. members, and cDNA from the original clones is amplified and purified for each DNA of the 2000 genes. The purified DNA is spotted and fixed on the glass plate for a DNA chip and applied to the mRNA pool whose gene expression profile is known, and the detection conditions are studied for the DNA chip and specifications are optimized. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Novel No.2). Achievement report on development of high-strength ultralight biocompatible implant material using porous titanium; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (shinki No.2). Takoshitsu chitan ni yoru seitai shinwasei kokyodo chokeiryo implant zai no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An implant material manufacturing technology is developed for which a titanium based metal material is made porous and osteoblasts are allowed into holes in the material surface for the establishment of fixation and mechanical similarity between the material and bones. Activities are conducted in the six fields of (1) the establishment of material adjusting technology, (2) establishment of high-porosity sintering technology, (3) research and development of hydrogen-aided technology of pore formation, (4) improvement on mechanical characteristics/dimensions evaluation technology, (5) establishment and implementation of biocompatibility evaluation technology, and (6) the development of technology for commercializing high-porosity implant materials. In field (3), pure titanium and titanium hydride are pulverized and classified, and very fine powders only are mixed and sealed into a capsule made of pure iron, which is subjected to extrusion into bulk and then heated to a high temperature for the generation of hydrogen gas for the formation of a limitless number of pores. Pure titanium and a Ti-Al-V-Mo-Fe alloy easy to treat in a low-temperature superplastic process are used for the study of the process. In field (6), in the wake of element technology development, commercialization of implant materials is considered, technical tasks to discharge before new industry creation are made clear, and measures in this connection are studied. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Energy conservation No.3). Achievement report on development of micro-scale boiling aided high efficiency heat removing device; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (shoe No.3). Micro scale boiling ni yoru kokoritsu honetsu device no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies are conducted about basic matters of heat transfer with boiling, such as critical heat flux intensification, prevention of dry-out, and the development of refrigerants suitable for use for heat transfer with boiling, for the purpose of developing boiling heat conduction type high-efficiency heat removing devices for use in electronics, and then heat removing devices usable as power devices in the future are experimentally designed. Activities are conducted in the three fields of (1) the study of basic micro-boiling technology, (2) development of micro-scale boiling element technology, and (3) international joint studies. Efforts are made to develop the technology of removing heat from ultrahigh heat fluxes using a micro-valve in field (1), to develop the technology of heat transfer by boiling in a micro-channel in field (2); and to develop the technology of critical heat flux intensification in a boiling heat exchanger in an electromagnetic field (3). In an effort to develop the technology of heat removal, a heat transfer plate is installed at the bottom of a path which is narrow, horizontal, and rectangular, and distilled water is allowed to flow and boil. Micro-bubble emission boiling occurs by a subcooling degree of 40K at an average flow rate of 0.5 m/s, and an ultrahigh heat flux of 2-7 times 10{sup 6} W/m{sup 2} is obtained. The value is 2-4 times as high as the current IC chip critical heat flux. (NEDO)

Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

Energy Technology Data Exchange (ETDEWEB)

1991-11-07

Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

Report on the results of the FY 1999 introductory R and D of MGC ultra-high efficiency turbine system technology. International cooperative project of MGC technology investigational study (R and D on advanced engine and energy saving use ceramics); 1999 nendo MGC chokokoritsu turbine system gijutsu sendo kenkyu kaihatsu seika hokokusho. MGC gijutsu chosa kenkyu kokusai kyoryoku jigyo (senshinteki engine oyobi sho energy yo yotoyo ceramics ni kansuru kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

As the R and D of advanced engine and energy saving use ceramics, this project is being conducted by the U.S., Germany, Sweden, Belgium and Japan under Annex II of the Committee of Energy Research Technology (CERT) established by International Energy Agency (IEA). For structure use ceramic materials, their raw material powder is tested and a method to evaluate characteristics of their sintered bodies is studied. The research was divided into Subtask 11 (test on mechanical characteristics) and Subtask 12 (evaluation of raw material powder). Each subtask decides on the details of the international joint research and the associated research assigned to each country. In the testing study on mechanical characteristics in this fiscal year, the evaluation method was studied of thermal characteristics of materials for heat resistant high temperature members. In the study for evaluation of raw material powder in this fiscal year, a method was studied for evaluation of characteristics of fine ceramic powder. The results to be obtained in this study are related to mechanical characteristics of materials for heat resistant high temperature members and to the basic evaluation method of characteristics of raw material powder. The results of the study are surely indispensable for promotion of the application of these materials. (NEDO)

Fundamental cooperation project in fiscal 2000 for improving international energy consumption efficiency. Investigations in relation with prevention of global warming (analytical comparison centering around cost effectiveness related to greenhouse effect gas (GHG) reduction in overseas countries); 2000 nendo kokusai energy shohi koritsu ka chosa nado kyoryoku kiso jigyo - chikyu ondanka boshi kanren chosa hokokusho. Kaigai deno GHG sakugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to provide discussion materials for measures to achieve the GHG emission reduction target, investigations and discussions have been made on the following subjects: cost effectiveness of reducing GHG emission by target countries and target technologies, use of maps and databases on the possible reduction quantity of GHG emission, the targeted countries and business categories. Regarding the target countries, investigations were made on the general situation of the energy consumption efficiency, difference between their energy consumption efficiency by industries and that in Japan, and the GHG emission quantities by sectors. As a result, 31 counties hopeful in reducing CO2 emission were selected. With regard to technologies to reduce CO2 emission, technologies having been practically used and proliferated in Japan were used as the base, whereas 43 technologies were systematized for such departments as industries, business operations, households, and transportation. According to a trial calculation on the effect of CO2 emission reduction, if the 43 technologies are applied to the 31 target countries, CO2 emission reduction of 698 million tons as a whole would be possible, for which the required expense was calculated as 114.4 trillion yen. In evaluating the CO2 emission reducing technologies, the cost effectiveness of each technology was evaluated by cost per GHG emission reduction of 1t-CO2. (NEDO)

Fiscal 1998 research report (continued from the fiscal 1997 project). International survey project for rational energy use / Basic survey on efficient energy use in developing countries (Database construction project) / Survey on Japanese energy conservation technologies; 1998 nendo (1997 nendo jigyo kurikoshi) kokusai energy shiyo gorika nado chosa jigyo hatten tojokoku energy shohi koritsuka kiso chosa (database kochiku jigyo) chosa hokokusho. Nippon no sho energy gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

As a part of development of the energy conservation technology database, revision was made on 'Directory of Energy Conservation Technology in Japan' which was published to present the energy conservation technology of the Japanese energy-intensive industry to Asian countries in fiscal 1996. The previous directory was composed of 307 technical items, and 126 items among them were deleted and new 63 items were added through this revision. The technologies with energy conservation effects more than 10% were mainly selected by knowledge of the industrial members of the committee and other specialists. The energy conservation effect widely ranges from low-level one to high-level one, and the number of all the energy conservation technologies is enormous. Consequently, it should be considered that the applicable extent of the energy conservation technologies is dependent on the energy cost or economical situation of Japan and developing countries. (NEDO)

Fiscal 1999 survey report. Survey of feasibility of international cooperation in the transfer of technology; 1999 nendo gijutsu iten ni kakawaru kokusai kyoryoku kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Among the activity goals of CTI (climate technology initiative), which is a framework designed to encourage international cooperation of leading nations in the voluntary development and diffusion of technologies supposed to contribute to the reduction of greenhouse gas emissions, there is the promotion of the transfer and diffusion of climate change preventing technologies. To achieve the goal, energy efficiency oriented workshops will be held as part of the training for the raising of people skilled in energy saving, the results will be examined, the achievements attained at such events will be introduced at COP5 (Conference of the Parties at Bonn), and the responses of the respective countries will be reviewed, all these for the investigation of the feasibility of international cooperation for raising people dedicated to the reduction of greenhouse gas emission. In this fiscal year, aiming to make clear the possibility of contribution to the transfer of software-related technologies through cooperation of multiple nations, lecturers from leading countries and participants from developing nations met, held a workshop over energy efficiency technologies, and the results were compiled. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Overall survey; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper summed up the results of the survey of tackling with the international standardization by enterprises and organizations involved in the standardization in the U.S., Europe and Japan, the results of the R and D on 20 themes for the international standardization, and the development toward the international standardization. As the R and D themes, the following were selected: the development of chemical method to analyze/evaluate metallic coatings of surface treated steel coating sheets, R and D of the basic evaluation method of functional composite particles, international standards for computer/manikins, basic technology of color image management, study on optimizing design/evaluation technology using quality engineering, study of the international standardization by economic evaluation of environmental impacts, R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells, development of a test method of halogen-free flame-retardant cables and a study of the cable standards, standard measuring methods of hormone effects of chemical substances, quantification of the sensory evaluation and international standardization in the paint field, experimental study on the international standardization for immunochemical measurement of chemical substances, etc. 24 figs., 16 tabs.

Report on a feasibility study of making an international joint research on energy in the Asia region; Asia chiiki kokusai kyodo kenkyu kanosei chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A survey was conducted on the energy situation in Thailand, Indonesia, Malaysia, the Philippines and India, and a possibility of making an international joint research. Thailand has sharply increased investments from Europe and the U.S. since 1985, and has been making a rapid industrialization. As to the energy policy, it is important to secure the stable supply and stabilize the price. Indonesia has been rapidly increasing energy consumption in accordance with the recent economic growth, and is fear of becoming a net oil importing country in the near future. They are taking a policy for securing as much domestic oil and gas as possible. Malaysia has been keeping a high growth of over 8% per year for the past 8 years and rapidly increased energy demand. It is expected that they will maintain a high level of the development of energy resources. In the Philippines, the industrial energy is mostly coal, but electricity expected in future is from the oil-fueled power generation. The stable import of oil is a problem. 45 figs., 51 tabs.

Fiscal 1996 report on the committee for international collaborative research of medical and welfare apparatus; 1996 nendo chosa hokokusho (iryo fukushi kiki kokusai kyodo kenkyu jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

From a viewpoint that cancer, cerebral hemorrhage, heart disease, etc. caused by the progress in aging are problems not only to Japan but to all developed countries, a possibility of Japan`s joint study with other countries was examined to promote efficiently and effectively research/development of the apparatus required. Moreover, from a viewpoint of being the same Asian countries, a possibility of the joint study was examined also with developing countries which are largely different in disease structure and environment of the use of apparatus from developed countries. In the examination on medical/welfare apparatus technology of China, before the site examination, a book of data was arranged on the actual state of population and disease structure and the R and D situation of medical/welfare apparatus in Japan, and at the same time, celebrated persons in China were introduced by the scientific society side as widely as possible. By this preliminary study, the original objective of the examination could be achieved. In the examination with the U.S. and Europe, Japan held meetings with engineers of the U.K., France and the U.S. Japan`s `load control type walking supporting apparatus,` of which the development was finished, was very highly evaluated by each organ of the countries

Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

Report of the 8th International Symposium on the Observation of the Continental Crust Through Drilling; Dai 8 kai tairiku kagaku kussaku kokusai symposium ni sankashite

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K. [Super Deep Core Drilling Study Group, Japan, Tokyo (Japan)

1996-11-29

This report relates to the 8th International Symposium on the Observation of the Continental Crust Through Drilling, convened at Agency of Industrial Science and Technology, Tsukuba City, on February 26, 1996. The symposium was represented by approximately 200 people from the U.S., Canada, Britain, Germany, France, Russia, China, and some others, who discussed active faults, drilling and logging, transfer of fluids and heat in the crust, history of the earth and climate, ICDP (International Continental Scientific Drilling Program) and international cooperation under this program in the future, etc. In reference to ultradeep drilling in the world, drillings by Germany`s KTB (Kontinentales Tiefbohrprogramm)(9,101m deep) and Russia at Kola Peninsula (l2,261m) were reviewed. Concerning the efforts of U.S. Continental Scientific Drilling Program during the previous 11-year period, it was reported that it had cost a total of $84,000,000; that investigations had been made into volcanos and geotherm, fault tectonics, sedimentary basins, holes due to meteorites, and metal ore deposits; and that 61 holes (total length: 31,310m and maximum depth: 3,510m) had been drilled and investigated. 6 figs., 3 tabs.

WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for aircraft engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Koku engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-01

With an objective to utilize hydrogen fuel in aircraft engines, a conceptual design survey was carried out on medium size transport aircraft. Large size long-distance aircraft and SST loaded with a great amount of fuel have the jet fuel (JP) increase take-off weight, affecting largely the selection of wing area and engine thrust. If the hydrogen fuel can be liquefied, large reduction can be achieved and the economic effect can be increased. However, for short-distance transport aircraft, the fuel weight ratio is small, where no large advantage is anticipated even if hydrogen is liquefied. Nevertheless, considering oil depletion in the future, a conceptual design was performed on the YX2688 short-medium distance aircraft being discussed of development. Even the short-medium distance aircraft that can be developed and commercialized as civilian use aircraft has a number of common points with large aircraft development, such as hydrogen fuel using technologies and safety. Although the advantage of using liquefied hydrogen as fuel may of course be smaller in the short-medium distance aircraft than in larger aircraft, the trend of using hydrogen fuel is historical necessity, whose development plans should be moved forward. (NEDO)

Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education - iron and steel (Survey on education accreditation in material field); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (tekko) -Zairyo bunya ni okeru kyoiku nintei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, a survey was performed on external accreditation systems for engineer education such as in universities and other organizations in the material field. In the survey, discussions were given on whether or not the education program accreditation system for the material field being structured has any problem in the actual operation of the accreditation through trials at Chiba Engineering University and Tokai University. As a result, it was revealed that the criteria are too general, requiring more detailed description on the guideline, and criteria should be so considered that assessment at higher levels can be given to the graduation research, which is a Japan's particular education system. In addition, it was made clear as a problem in the education programming side that a room for improvement remains in the education methods for the engineering ethics, communication skills, and the method for evaluating the students' achievements. In the survey on the methods for examination and accreditation in the U.S.A. it was found out that education organizations are perplexed with the new criteria of EC 2000. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for chemical utilization); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-04-15

Surveys and studies were performed on chemical utilization of hydrogen regarding its status of development and utilization inside and outside the country, as well as its future prospect. This paper describes chemical utilization of hydrogen in ammonia, methanol, petroleum refining and other industries as the existing fields. It also describes chemical utilization of oxygen in iron and steel, chemical and other industries. It describes methanol as a pollution-free auxiliary fuel for electric power plants as a new type of hydrogen application. Acetic acid made by using the Monsanto method which carbonylate methanol is drawing attention in terms of economy, and is in the phase of discussing commercialization. Synthesizing ethylene glycol from carbon monoxide and hydrogen may be conceived economically. Methanol for synthesized protein depends on the possibility of future development. In the iron and steel industry, electric furnace steel makers are planning production of reduced iron, where the direct reduction process using hydrogen is considered as a complementary process, including countermeasures for scrap iron. This paper estimates hydrogen amount as a raw material for ammonia to remove NOx by using the ammonia reduction process. It also describes possibility of other types of utilization. (NEDO)

Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the chemical utilization); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-07-01

This paper reports on the present situation of the chemical use of hydrogen and oxygen, and the short-term, medium-term, and long-term forecast. The main usage of hydrogen is ammonia synthesis, petroleum refining, and methanol synthesis. In the usage of these three, there are factors of structural changes now and in future, and it is extremely difficult to predict the amount in a short term up to around 1980. In a medium term prediction, from the result of predicting the demand of ammonia, methanol and hydrodesulfurization, the total 1985 hydrogen demand is estimated at approximately 60 billion Nm{sup 3}, and approximately 67 billion Nm{sup 3} as the gross hydrogen demand. Further, judging from that synthetic protein, fuel use methanol, and reduced iron are estimated to reach a certain production size in and after 1985, new demand for hydrogen is expected to be approximately 100 billion Nm{sup 3} mostly including fuel use methanol. In a long term prediction, it is extremely hard to predict the demand because of various factors existing in Japan and abroad. As predicted in a medium term, the amount of chemical use of hydrogen is expected to increase more and more, even if calculating it only in the field of ammonia synthesis, petroleum refining, and methanol synthesis. (NEDO)

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y [Hiroshima University, Hiroshima (Japan); Okusu, M [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1997-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Survey on the feasibility of high-efficiency gas turbine power generation system; Kokoritsu gas turbine hatsuden system ni kansuru jitsuyo kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For higher-efficiency power generation cycle plants with less restrained conditions for a location, the conceptual design of an inter-cooled regenerative two-fluid cycle plant (ISTIG) was attempted using a modified aircraft gas turbine. A high-performance turbo fan engine is used for middle-class power generation. The first stage combustion gas drives the first stage turbine, and its exhaust gas is used for the second stage combustion. Because of two-axial type of high and low pressure, improvement of thermal efficiency is expected by easy-to-install inter-cooler. ISTIG superior in operability is suitable for medium load or distributed power generation facilities, and aims at higher efficiency of a 60% level. ISTIG includes a large amount of water vapor in combustion air by adopting a diffusion type combustor eliminating back fire, and can reduce exergy loss by preheating fuel gas. Since load of the high-pressure turbine shifts toward low-pressure one by the inter-cooler, some considerations are necessary for low-pressure side cooling together with reheating cycle. Because of unnecessary steam turbine, the construction cost per kW can be reduced by 20%. 41 refs., 64 figs., 27 tabs.

Required grades of hull steel plates in consideration of fracture toughness; Hakai jinsei wo koryoshita sentaiyo koban shiyo kubun ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Yajima, H; Yamamoto, M; Ogaki, Y [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1997-10-01

This paper discusses the required grades of hull steel plates based on the steel ship rule of Nippon Kaiji Kyokai (NK). The minimum value of the allowable crack length in NK rule (critical safety crack length at 0degC just before brittle unstable crack causing fatal fracture) was estimated. In the case where the estimated crack tip exists in a matrix, the crack length was a minimum of 200-210mm, while nearly 60mm in a fusion line at high-heat-input welded joint. The allowable crack lengths estimated from a specified value in the NK rule were fairly different. The allowable crack length at 0degC was also estimated from the minimum value in V-notch Charpy impact test. The private proposal on the required grades of hull steel plates in consideration of fracture toughness was discussed. Thirty-five percent of crack lengths found in real ships is 100mm or less, however, cracks of 250-400mm long are frequently found suggesting the allowable crack length of 400mm. The required grade integrally considering required values and design conditions is demanded to secure the reliability of hull strength. 5 refs., 5 figs., 2 tabs.

Survey report on an environmental harmony type production system of chemical products; Kankyo chowagata kagaku seihin seizo system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

As part of establishing an environmental harmony type production system of chemical products, study and survey were made on PET bottles. Using the life cycle analysis method (LCA), a study was made for proposing a material recycle (MR) method which is environmentally and economically excellent in the stage of recycling waste PET bottles. The total cost of recycling can be reduced by 34% supported by a decrease in equipment cost and improvement in yield if there is no mixture of foreign substances such as aluminum caps and PVC bottles. However, the ratio of the amount obtained from the reduction to the total production cost is small, and it is necessary to take measures from a viewpoint of the cost in a total production process and environmental loads. In a survey in Kawaguchi city, PET bottles discharged from the business sector occupied 41% of all the discharge amount. In a survey in Yokohama city, very important data were obtained on PET bottles appointed as the second type under the recycle law. The quality of PET bottles to be brought to the recycling plant is important for effectively processing PET bottles in MR method. For achievement of MR which is low in cost and small in environmental load, needed were cooperation by citizens, the shipping management system in autonomous government, and changes in design and material quality to be made by the industrial circle. 8 refs., 64 figs., 68 tabs.

Basic studies on application of vegetable factory in Tohoku region; Tohoku chiho ni okeru yasai kojo no jitsuyoka ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Okano, T; Terazoe, H; Shoji, K; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan); Tanaka, M; Miura, K [Tohoku Electric Power Co. Inc., Sendai (Japan)

1995-08-01

To construct vegetable factories in the Touhoku region, items of information have been collected with respect to items to be cultured and market conditions. Experimental discussions have also been given on new culture items and methods for utilizing snow. Using the results of investigations on the market conditions and weather environments, the following three kinds of spicy vegetables were selected: water cress which grows in about 46 culture days after seeding and in about 36 days by herbaceous cutting to a harvest of about 700 g/m{sup 2}, green perilla which grows in about 85 culture days to a number of salable leaves of 100 per stock, with an average leaf area of about 55 cm{sup 2}, and trefoil which grows in about 56 culture days to a harvest of about 5100 g/m{sup 2}. According to a storage experiment using snow, lettuce packed with snow in a box retained at a temperature of 5{degree}C and a humidity of 100%, pre-cooled for one day and then stored for six days in a refrigerator at 5{degree}C presented very little decrease in fresh weight and no decrease in freshness. The same result was obtained also for the Sunny Lettuce. 9 refs., 19 figs., 9 tabs.

Estimated method of permeability in the granitic rocks by geophysical loggings; Butsuri kenso shuho ni yoru kakoganchu no tosuisei ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Matsuoka, K; Hashimoto, N. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)]Ogata, N. [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

1997-10-22

Water permeability in granite is estimated by performing geophysical investigation using a 500m-deep test hole drilled in granitic rocks in the vicinity of a Tono mine. The investigation consists of flowmeter logging and geophysical logging. In flowmeter logging, a probe is moved up and down in the hole at a constant speed by use of a cable, and the cable speed and impeller revolution are used to workout the relative speed of the fluid in the hole. In the geophysical logging, a probe attached to the leading end of a logging cable is replaced with other probes so as to acquire different geophysical data. In a hole drilled in a crack-abundant rockbed such as a granitic rockbed, the inflow and outflow of ground water is governed mainly by water-permeable crack zones, and the result of the flowmeter logging show that this hole has three highly water-permeable zones. Using the results of the loggings, a correlative equation is worked out between changes in flow speed and changes in permeability index obtained by hydraulics tests. Among the various results achieved by the geophysical logging, a fine correlationship is found between an equation relative to permeability obtained using electricity and density and water-permeability indexes obtained by hydraulic tests conducted in situ. 4 refs., 8 figs., 1 tab.

Consideration on standard substance for the conbustion test of oxidizing solid. Sankasei kotai no nensho shiken no kijun busshitsu ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Muranaga, K [The Japan Carlit Co. Ltd., Tokyo (Japan); Tamura, M; Yoshida, T [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1991-04-15

The mixture of KClO {sub 3} and wood flour is the standard substance in the combustion test by the Fire Service Law to investigate the accelerating combustion of an oxidizing agent, but it is difficult to measure the combustion time owing to the intermittent combustion. This paper described the study to get any compounds superior to the above mentioned. Since the mixture of KNO {sub 3}-wood flour combusts more rapidly than that of KClO {sub 3}-wood flour, a new mixture of similar combustion rate to that of the mixture of KClO {sub 3} and wood flour and without intermittent combustion was tried to get by adding an inactive solid powder to decrease the combustion rate. But a new mixture which has the combustion time of about 4 minutes, shows uniform combustion instead of intermittent combustion and shows the only slight variation of combustion time, could not be found. It is because of intermittent combustion that the mixture of KClO {sub 3} and wood flour can endure the combustion for 4 minutes although this mixture has larger reaction heat. The combustion time of this mixture is shortened if the igniting nichrome wire temperature exceeds 1,000 centigrade. Further, the bulk density of deposit affects greatly the combustion time. 7 refs., 2 figs., 4 tabs.

Investigation on behavior of bacteria in reservoir for microbial enhanced oil recovery; Biseibutsuho (MEOR) no tameno yusonai saikin katsudo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, K.; Tanaka, S.; Otsuka, M.; Nakaya, K. [Kansai Research Institute, Kyoto (Japan). Lifescience Research Center; Maezumi, S.; Yazawa, N. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Hong, C.; Chida, T.; Enomoto, H. [Tohoku University, Miyagi (Japan). Graduate School of Engineering

2000-07-01

Behavior of bacteria activated in reservoir though molasses-injection-tests, was investigated using the restriction fragment length polymorphism analysis with the polymerase chain reaction (PCR-RFLP) method, for elucidating potential bacteria to suppress in situ growth of microbes to be injected into the reservoir in the microbial enhanced oil recovery (MEOR) process. As a result, some bacteria belonging to Enterobacteriaceae species or their close relative species were grown predominantly in the reservoir, among bacteria inhibiting in the ground-water. The foregoing indicates that behavior of these bacteria in reservoir must be taken into consideration when giving a full account of behavior of microbes to be injected into the reservoir to put the MEOR process into operation. Potential proliferation using molasses to activate those bacteria was also estimated on the laboratory tests, to clarify the growth of microbes to be injected into the reservoir to operate the MEOR process. In consequence, it became clear that these bacteria have a potential growth exceeding 10{sup 8} CFU/ml, utilizing molasses. These facts indicated that microbes to be injected into the reservoir at the MEOR field tests are necessary to grow more excellently than bacteria inhabiting in the ground-water. In addition, as flow, the injection fluid is influenced by reservoir heterogeneity caused by injection of molasses, it was inferred that microbes to be injected into the reservoir at the MEOR field process are also necessary to grow more remarkably than bacteria inhabiting in the reservoir brine at high permeability zones and bacteria inhabiting in the reservoir rock. Furthermore, the results of the functional testing for MEOR conducted in the presence of bacteria activated through molasses-injection-tests indicated the importance of effective use of microbes to be injected, taking into account the characteristics of the reservoir and function for MEOR of those microbes. (author)

Evaluation for characteristics of around the Nojima fault; Butsuri tansa ni yoru `Nojima jishin danso` shuhen no jiban bussei ni kansuru ichihyoka

Energy Technology Data Exchange (ETDEWEB)

Shimizu, K; Tsuji, T [Newjec Inc., Osaka (Japan); Tsuji, M [OYO Corp., Tokyo (Japan)

1996-05-01

Various surveys were conducted for the area around the Nojima fault, including ground surface, two-dimensional electrical and boring surveys and elastic wave tomography, in order to grasp properties of the ground around the `Nojima earthquake fault.` The resistivity image method as one of the two-dimensional electrical methods was used to grasp fault shapes over a wide range of the 1.6km long section extending between Esaki and Hirabayashi. The courses of traverse were set in the direction almost perpendicular to the fault. Boreholes were excavated and elastic wave tomography was conducted between the boreholes on the 9th and 17th courses of traverse, to confirm ground/mountain conditions and to compare the results with observed elastic wave velocities. Very low resistivities are observed at places where granite is distributed, suggesting that the fault-induced changes are not limited to the area around the fault. The zone in which elastic wave velocity decreases is narrow, 10m at the longest, at a velocity of 2.4km/s or lower, which is a low velocity for that propagating in granite. 5 refs., 4 figs.

Research on improvement of indoor air quality and prevention of fungi; Shitsunai kuki kankyo no kaizen to kabi boshi ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Tatsuaki [Ochanomizu University, Tokyo (Japan). Faculty of Human Life and Environmental Sciences

1998-12-16

An epidemiological survey survey was performed to elucidate the fungal flora of a dwelling house. The measurements were carried out in an apartment in Yokohama from Jul. 1996 to Dec. 1997. Fungi were isolated from 106 sampling points (the surface of the walls, floors, etc.) with sterile stamps. It was proved that Cladsporium, Penicillium, Eurotium, and Yeasts showed characteristic distribution. Especially Cladsporium was not isolated from the spring to the summer, but increased in the autumn. In addition to the survey, experiments on fungal growth temperature (13, 20, 25, 30, 36, 42 degree C) and water activity (A w 0.75{approx}0.97) were carried out. Cladsporium grew well in 13, 20, 25 and 30 degree C, but didn't grow in 36 and 42 degree C. In addition, the growth activity of Cladsporium was down below Aw 0.91. Eurotium was isolated from under Tatami, where it has an unchanging temperature and relative humidity. Yeasts preferred very high humidity. It was concluded that environmental factors such as temperature and relative humidity related to the growth of fungi. (author)

Study of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu keisei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

1998-05-01

A study is being made on premixed lean diesel combustion (PREDIC) by means of early fuel injection in diesel engines. The PREDIC makes it possible to largely reduce NOx emission, but has such problems as ignition control and increase in THC and CO generation. In order to clarify the relationship between fuel spray characteristics in the PREDIC and properties of gas mixture and exhausts, the present study has investigated spread and internal structure of the spray by means of spray observation experiment using a pintle swirl nozzle. Based on the result therefrom, simulations were used to investigate effects of spatial dispersion characteristics of the spray on properties of the gas mixture and exhausts before ignition. The pintle swirl nozzle forms conical spray having an air layer inside the spray, where penetration is suppressed even under low atmospheric pressure. By forming hollow spray or solid spray in the conical spray, a possibility was indicated that equivalent ratio distribution of the gas mixture can be controlled and NO emission may be reduced. 8 refs., 12 figs., 1 tab.

Study of high load operation limit for premixed compression ignition engine; Yokongo asshuku chakka kikan no kofuka unten genkai ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Shimazaki, N. [Isuzu Advanced Engineering Center Ltd., Kanagawa (Japan); Akagawa, H. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Tsujimura, K. [Chiba Institute of Technology, Chiba (Japan); Miyamoto, T.

2000-11-25

NO{sub x} emission was remarkably reduced by PREDIC (PREmixed lean DIesel Combustion) system in which fuel was injected at very early stage of compression stroke and the major part of the fuel is considered to be burned with self-ignition of premixed charge around TDC. However PREDIC system had some problems, a restriction of a high load operation was one of these problems. In order to investigate the combustion characteristics of PREDIC at the richer operation limit, a test engine was operated with gaseous fuel-air mixture where less heterogeneous mixture can be formed than that of conventional diesel engines. A steep pressure rise or the abrupt increase in NO{sub x} emission determined the richer operation limit. This was at 2 to 2.4 of excess air ratio. Supercharging operation enabled the high load operation more than 2.4 of excess air ratio. (author)

Fiscal 1999 research cooperation project report. Research cooperation on coal liquefaction technology; 1999 nendo sekitan ekika gijutsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research cooperation project result on coal liquefaction technology. Cooperative FS was made on coal liquefaction technology of Indonesian coal as petroleum substituting energy. To obtain the basic data necessary for the FS, study was made on the applicability of Indonesian natural minerals as catalytic materials. Promising low-cost abundant Soroako Limonite ore showed a high catalytic activity for liquefaction reaction of Banko coal, and an excellent grindability. Improved BCL process including hydrogenation process was promising for production of high-quality coal liquid superior in storage stability with less nitrogen and sulfur contents. Survey was made on the general conditions of Tanjung Enim area including South Banko coal field concerned, and the geological features and coal seam of South Banko coal field which is composed of 3 seams including coal deposits of 6.35 hundred million tons. To study the marketability of coal liquid, survey was made on the current situation of oil, oil product standards, and blendability of coal liquid. Hydrogen for the liquefaction process can be obtained by coal gasification. (NEDO)

Application of photovoltaic generating system to electric power in large ship; Taiyoko hatsuden system no ogata senpaku eno oyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Katagi, T; Ogawa, S; Nishikawa, E; Hashimoto, T [Kobe University of Mercantile Marine, Kobe (Japan); Ishida, K

1996-10-27

This paper describes the design of electric power system in a ship with photovoltaic power generating system, to examine applicability of the photovoltaic power generating system to the inboard power source. It also discusses effectiveness of the system for sea environment. At first, the actual route of a car carrier, meteorological data, and quantity of power consumption were picked up from the deck logbook and engine logbook. Then, the installation area of photovoltaic arrays, the quantity of photovoltaic power generation derived from the quantity of solar radiation, and the capacities of batteries and inverters were calculated, to design the electric power system in the ship with photovoltaic power generation system. Moreover, the NOx and SOx emissions were compared between the present power system and the usual power system using diesel power generator, to discuss the effectiveness of the present system for sea environment. Consequently, it was found that the emission of NOx was reduced by about 33% and the emission of SOx was reduced by about 28% compared to the usual power system. The effectiveness for sea environment was confirmed. 9 refs., 5 figs., 4 tabs.

Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y. [Hiroshima University, Hiroshima (Japan); Okusu, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1996-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Study on collapse behavior of a square plate subjected to water pressure; Suiatsu wo ukeru kukeiban no atsukai kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yao, T; Fujikubo, M; Mizutani, K [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1996-04-10

Bottom plates of a hull are subjected to laterally distributing force due to in-plane compression force and water pressure in the ship`s length direction as a result of longitudinal bending in a hogging condition. Because buckling collapse of the hull bottom plates leads directly to longitudinal bending collapse of the hull bottom cross section, the hull bottom plates must have sufficient strength. The present study performs a static elastic large deflection analysis and an elasto-plastic large deflection analysis. It elucidates buckling collapse behavior of a square plate subjected to water pressure and in-plane compression load, and considers limits in application of conventional approximation analysis methods. In the case of a water pressure action, deflection components growing in excess of the buckling load do not necessarily correspond to buckling modes of the case where no water pressure is acting upon. Conventional approximation analysis methods may not be able often to pursue actual buckling phenomena. According the result of an analysis on hull bottom panels of an actual ship, the ultimate strength decreases when the water pressure is large. Compression force in the lateral direction as a result of water pressure acting on ship`s sides affected very little the ultimate strength. 3 refs., 7 figs.

Consideration on longitudinal bending moment in waves of a large high-speed ship; Ogata kosokutei no haro tatemage moment ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Deguchi, M; Takimoto, T; Kasuda, T; Tozawa, S [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1996-04-10

While high-speed ships are on a trend of increased speed, size and diversity, one of the most important items is a discussion on large high-speed ships with a total length of 100 m class on their longitudinal strength in waves. With such a background, a model ship intended of realizing a large high-speed was assumed, and verification of reliability in structural strength and establishment of a design method for this ship were intended. Therefore, oceanographic condition setting, design load setting, FEM analysis, and strength assessment were carried out. This paper reports the results of comparison with and consideration on conventional criteria and linear calculations, mainly the results of simulated calculations on non-linear hull movement/wave load which have been performed in discussing the loads. The result of the non-linear simulation is thought to have well simulated non-linearity characteristic to the ship. Conventional criteria which have been arranged on the record of use for small ships are considered impossible to be applied to large high-speed ships. Under such a situation, the simplified equations by Kaneko et al are judged effective in making an initial plan for this type of ship. 6 refs., 7 figs., 2 tabs.

Research and development on a single-frequency simultaneous two-way cellular wireless device; Ichishuha doji sohoko ido musenki ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A cellular wireless device performs signal transmission and receiving using only one assigned frequency because of effective frequency utilization, and therefore, is inconvenient in actual use. For this reason, a cellular wireless device operating on a new principle was developed to make simultaneous two-way calls possible on one frequency. The operation principle is such that one frequency is used, voice signal is divided on the transmission side at every 0.4 second, compressed in time to 1/2, and transmitted in 0.2 second upon modulation; and the receiving side extends the signal to a double length upon demodulation to take out the original voice signal. Thus, the transmission time is reduced to half, and the remaining half time thus obtained is assigned to the receiving time from a caller in the similar method to perform a two-way simultaneous call. Both hands can be used freely during a call, making the safe call possible even while driving a vehicle or performing a work. High confidentiality can be maintained by means of voice processing, compression, and extension. Size of the device was reduced, reliability and clarity were optimized, and a large number of frequency can be switched easily. Field test have proved that the device meets the criteria specified in the Electric Wave Law. The device was begun of business use in 1992. It can be connected with portable type telephone sets and those used in business compounds. 2 figs.

Report on evaluation of research and development of superhigh-function electronic computers; Chokoseino denshi keisanki no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-02-20

Described herein is development of superhigh-function electronic computers.This project was implemented on a 6-year joint project, beginning in FY 1966, by the government, industrial and academic circles, with the objective to develop standard, large-size computers comparable with those of the world's highest functions by the beginning of the 70's. The computers developed by this project met almost all of the specifications of the world's representative, large-size commercial computers, partly surpassing the world's machine. In particular, integration of the virtual memory, buffer memory and multi-processor functions, which were considered to be the central technical features of the computers of the next generation, into one system was a Japan's unique concept, not seen in other countries. The other developments considered to have great ripple effects are seen in LSI's, and techniques for utilizing and mounting them and for improving their reliability. Development of magnetic discs is another notable result for the peripheral devices. Development of the input/output devices was started to correspond to inputting, outputting and reading Chinese characters, which are characteristics of Japan. The software developed has sufficient functions for common use and is considered to be the world's leading, large-size operating system, although evaluation thereof largely awaits the actual specification results. (NEDO)

Hydraulic mechanism of siltation in approach channels and harbors. Siltation ni yoru koroter dot hakuchi maibotsu no suiri kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Irie, I [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering; Murakami, K; Tsuruya, H [Ministry of Transportation, Tokyo (Japan). Port and Harbour Research Inst.

1991-11-20

The phenomena that clay or mud is carried away by waves or currents and deposited in approach channels and harbors are called siltation, and hinder often seriously the navigation of vessels and their arrival at as well as departure from wharves, etc.. In this paper, the hydraulic mechanism of siltation in harbors and approach channels in the sea area is chozen in particular, and waves and currents as the external force governing the travel of bottom mud, the properties of sunken mud, the supply source of sunken mud in approach channels, and grasping of the mud sinking mechanism as well as countermeasures against mud sinking are stated mainly centering around the results obtained from the in situ observations at Kumamoto Port and Banjarmasin Port and their mathematical calculations. The bottom mud traveling mechanism has been accepted as a study subject respectively from such wide viewpoints as river engineering, agriculture, environmental engineering, sanitary engineering, chemical engineering and mechanical engineering, and in addition, it has been under study by coastal engineering. Siltation under the wave actions is still in the state of research even in advanced countries in America and Europe. The siltation research in Japan has a short history, but this is the field which must be coped with positively. 19 refs., 17 figs.

Study of hydrocarbon emission in small direct injection engines; Kogata DI diesel kikan ni okeru teifukaji HC haishutsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tsurushima, T; Zhang, L; Ueda, T; Fujino, R; Yokota, K [Isuzu Advanced Engineering Center, Tokyo (Japan)

1997-10-01

The cause of unburned hydrocarbon emission in small DI diesel engines at light load was studied. An optically accessible engine which was enabled to visualize the squish area was used to investigate the behavior of spray, mixture distribution and so on. Based on these observations and engine tests, the factors such as the direct impingement of liquid phase fuel spray to the combustion chamber wall the unevenness of fuel spray among holes and spreading of the fuel droplets, mixture and flame to the squish area were supposed to be the cause of forming HC emission. 18 refs., 10 figs., 2 tabs.

Survey of implementation plan constructed for `the New Earth 21 Project`; Chikyu saisei keikaku no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

It is necessary to establish scenarios for reducing CO2 emissions and for developing CO2 emission control technologies to obtain a global consensus, using appropriate analytical models. For modification of the DNE-21 (Dynamic New Earth 21) model, it has a category designated as innovative technologies not involving CO2 emission and an optional consideration for the absorption of atmospheric CO2 by biomass. A global carbon circulation model, including vegetation in its scope, is also incorporated. Major results of the simulation are shown. When 20% reduction in CO2 emissions is required for only OECD countries after the year 2020, it has been demonstrated that CO2 concentration in the atmosphere will reach as high as about 900 ppm in 2100 due to CO2 emission by developing countries, and will not be a tolerable level. Under the condition that CO2 concentration in the atmosphere is controlled at 450 ppm in 2100, the amount of renewable source of energy from photovoltaic power generation and biomass will increase and technologies of CO2 recovery and storage will decrease. Research and development of the production of methanol from recovered CO2 will be adopted as innovative technology for CO2 measures. 69 refs., 112 figs., 79 tabs.

Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

Investigation and study on each technique and example of intelligent planning; Intelligent planning no kakushu shuho to jirei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-11

Various problems on intelligent planning (IP) and the tendency of basic technology were investigated. For each technique of IP, a Petri net and mark graph have been widely used as the modeling and analysis methods of a discrete event system. Moreover, various planning problems were modeled by a traveling salesman problem, and the efficient solution of the traveling salesman problem has been studied simultaneously. The tendency of the basic technology and application system viewed from an example of intelligent plant planning was investigated as an applied field of planning technology, with importance attached to the production system and robot planning. In the scheduling technology of the production system, the activation of an AI study and a new theory (i.e., architecture study) based on natural science information was investigated with the transition in the world as a trigger. A robot system has been planned in a wide range such as the environmental information acquisition planning of a robot. 202 refs., 69 figs., 4 tabs.

Fiscal 1997 survey report. Survey on the innovative well drilling technology; 1997 nendo chosa hokokusho. Kakushinteki kosei kussaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In the geothermal drilling, reduction of the cost of well drilling is an important subject for technical development. The geothermal resource development tends to be made at higher temperatures and at deeper wells. In the present drilling technology, the cost is rising with the exponentially increasing depth and temperature, and there is also occurring the technical limit. Accordingly, the survey clarified the limit of the present drilling technology/cost to point out the research trend of the drilling technology as substitute for the present one, possibilities of the introduction, and the R and D target and subjects. As to latest drilling systems abroad and in Japan, the following were surveyed to study and extract promising technologies and systems: improvement/application of drilling equipment/materials (enhancement of heat resistance of the main drilling equipment, etc., cooling effects of top drive, heat resistance verification of MWD tools, PDM, tricone bits, multi-stage cementing tools, etc.), heightening of drilling rates, trend surveys of slim hole drilling, control drilling, well maintenance/workover, and well design technology. 68 refs., 73 figs., 40 tabs.

Investigation of nitrous oxide (N2O) abatement technologies. 2; Asanka chisso (N2O) no teigen taisaku ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Emission amount of nitrous oxide (N2O) from anthropogenic sources is analyzed, and reduction effects by the abatement technologies are evaluated. The concentration of nitrous oxide in the atmosphere continues to increase and emissions from agricultural and ecosystem sources are drawing particular attention. For the emission of N2O in Japan, 8.28 Gg-N2O per year is emitted from fossil fuel combustion facilities, 6.95 from waste incineration facilities, 22.5 from transportation vehicles including automobiles, 26.7 from the chemical industry including establishments engaged in adipic acid production, 2.1 from sewage treatment facilities including septic tanks, 6.3 from farmland, and 7.1 from livestock excrement. For the N2O abatement technologies for different sources, fuel improvement, high temperature combustion, acceleration of reduction decomposition reaction, and development of catalysts are significant for the combustion technologies. In connection with N2O discharged in the process of adipic acid production, major businesses have internationally committed to up to 99% abatement of the N2O emissions by 1998. With regard to wastewater and sewage treatment facilities and septic tanks, improvement in COD/NO-N ratio, retention period, pH level, and reduction process is pointed out. 204 refs., 70 figs., 53 tabs.

Fiscal 2000 survey report. Survey and study of constellation satellites technology; 2000 nendo chosa hokokusho. Konsutereshon eisei gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demands for constellation satellites were surveyed and satellite systems were studied for extracting basic technical tasks relative to constellation satellite systems and for drafting space verification plans. For a constellation satellite system to accomplish its missions, two or more satellites have to be simultaneously navigated. It is assumed that its field of application will cover earth observation, information communication, risk management, disaster prevention, and the like. With such applications taken into consideration, surveys and studies were conducted about the need and marketability of constellation satellites, need of state-level involvement, and requests for missions to be imposed on a constellation system. For plural satellites to satisfy mission requests by coordinating with each other, it will be necessary to develop basic technologies, such as navigational guidance, communications control, system autonomous management, and operation on the ground. Functions and performance that a constellation satellite system are requested to have and basic technologies to be studied and developed were extracted, and space verification plans were drafted. (NEDO)

Report on `Survey of commercialization of intellectual ownership such as patent rights`; `Tokkyoken nado chiteki shoyuken no jitsuyoka ni kansuru chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A survey was conducted on research results in industrial circles, universities, etc. in the U.S., Europe and Japan, especially the state of how intellectual ownership such as patent rights is handled and the present situation of the commercialization of intellectual ownership, proposing problems and measures to be taken for promotion of practical use of excellent research results in Japan. The most important thing obtained from the survey is that study jointly by industrial circles and universities in the U.S. and Europe is much more advancing than that in Japan and is firmly established not only in industrial circles, universities and national research institutes, but in the whole society, actually producing a lot of favorable results. For Japan to catch up with the U.S. and Europe, needed is not only accumulation of the ideas in the past, but drastic measures to be taken from a new point of view. Concretely, it was proposed that by belonging intellectual properties such as patent rights to universities/research institutes and transferring their disposal rights to them, royalties of licenses are given back to inventors as incentives, and that as a body promoting the transfer to the industrial circle, `management organization` to which private vitality is introduced is established in universities/research institutes in order to promote interconnection between the industrial circle and universities. 15 refs., 35 figs., 36 tabs.

Survey on the life cycle system of a product with shared information; Joho kyoyugata product life cycle system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report provides and proposes new concept and optimization technology on the life cycle system of product for emission minimum. For the proposed life cycle system of product with shared information, the global emission minimum is realized by considering the final emission, the information is given to the product and shared in all the life cycle system, the information sending function is considered from the product, and the information necessary for material processing are actively used. For this life cycle system of product, development of the information model for the system, development of the technology of data saving, renewing, searching and sending, development of sensing and re-using technologies of the product for life cycle, development of the technology attaching information in the product for emission minimum, design of the guidelines of material composition, and research and development of materials for emission minimum are extracted and provided as tasks. 26 refs., 69 figs., 8 tabs.

Analysis and model-tests on vortex-induced oscillation of bridges; Kyoryo no uzu reishin ni kansuru sanjigen oto kaiseki to fudo jikken

Energy Technology Data Exchange (ETDEWEB)

Yamamura, N. [Hitachi Zosen Corp., Osaka (Japan); Ogasawara, M. [Kansai Electric Power Co. Inc., Osaka (Japan); Shiraishi, N. [Maizuru College of Technology, Kyoto (Japan); Nanjo, M.

1996-07-21

In order to predict the three-dimensional response to vortex-induced oscillation of bridges, a model was investigated using the aerodynamic force coefficient including vortex-induced and self-excited forces, and the nonlinear response coefficient expressing constancy of response to vortex-induced oscillation. In the analysis, change of frequency in wind by the self-excited force, aerodynamic damping term, effect of the mode, and correlation of the vortex-induced force along member axis were taken into account. The aerodynamic force and nonlinear response coefficients were identified from the homogeneous and turbulent flow results of wind tunnel tests using a two-dimensional spring support rigid body model with varied damping factor. The aerodynamic damping term can be estimated from the nonlinear aerodynamic force coefficient, but it was enough to calculate it from the quasi-stationary coefficient in general bridge profiles. The correlation of the vortex-induced force was obtained from measurements of the vertical variation components of trailing flow under the resonance state, or the pressure distribution of the member surface. When comparing to the wind tunnel test of three-dimensional model of cable-stayed bridge, the response amplitude by the present analysis method was consistent well with the test results rather than by the method in which the amplitude of two-dimensional model was corrected. 10 refs., 4 figs., 3 tabs.

Some studies on structural planning of long-span cable stayed bridge; Choshikan shachokyo no kozo keikaku ni kansuru 2,3 no kosatsu

Energy Technology Data Exchange (ETDEWEB)

Endo, T. [NKK Corp., Tokyo (Japan)

1997-06-20

Feasibility of cabled-stayed bridges with 1000m-grade spans is discussed while re-examining the plan for constructing a Great Tatara Bridge to connect Honshu and Shikoku, Japan, and in this process various tasks and questions are isolated. Some which will be problems in designing the new bridge structure are taken up, including the load-bearing capability of the bridge as a whole, vibration of long cables, resistance to long-period earthquakes, and accuracy management during the construction work. Findings are stated below. A cable-stayed bridge is not significantly different from a suspension bridge and is sufficiently feasible until the span exceeds 1500m. When the span is longer, however, the bridge beam cross section needs be designed very prudently in view of the great axial force and wind load to be imposed on it. Effective for the assurance of load-bearing capability for a long-span cabled-stayed bridge is a structure in which load is elastically confined in the direction of the bridge axis. In connection with vibration damping for very long cables, it is verified that a new dimpled cable suits the purpose of suppressing wind load from increasing without reduction in damping effect. 28 refs., 23 figs., 7 tabs.

Studies on connecting structure between steel shell and steel reinforced concrete; Kokaku to tekkotsu tekkin concrete tono ketsugo kozo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Morimoto, A. [Kinki University, Osaka (Japan). Faculty of Science and Engineering; Morikawa, H.; Ito, N. [Metropolitan Expressway Public Corp., Tokyo (Japan)

1996-02-15

On the insert reinforcing bar structure for the connecting part of the main tower of cable stayed bridges, this paper reports verification results on a load resistant safety with a full-scale model, structure analysis and construction work. The basic structure was composed of a drilled steel shell, inserted reinforcing bars, fixing structure of bars in lining concrete of the shell and a pressure bearing plate. As an experimental result, the connecting part had a sufficient load carrying capacity against both tensile and compressive loads. The shear stress of the insert reinforcing bar structure was estimated successfully under von Mises`s condition. The shear spring constant in deformation characteristics was linearly proportional to an inserted reinforcing bar ratio. In earthquake, nearly 60% of an allowable compressive load was transferred to concrete through the pressure bearing plate. The analytical results of load resistant deformation characteristics of the connecting part well agreed with experimental ones, and the proposed analytical model was applicable to estimation of a dynamic behavior. 5 refs., 22 figs., 4 tabs.

Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

FY 2000 Report on the survey results. Survey on international cooperation for medical treatment/welfare equipment; 2000 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The NEDO's representatives visited Europe and China with the objectives of, e.g., international cooperation and information exchanges for medical treatment/welfare equipment. For the welfare equipment technologies, they visited the research institutes and facilities in UK and Germany, among others, to find that the European countries place more emphasis on researches to meet the needs than on advancing the equipment itself. For the medical treatment equipment, they visited the bio-research institutes in Europe for exchanging information on post-genome and tissue engineering. The European countries are behind USA in research fund and manpower for bio-technology and bio-medical, although making great efforts with much expectation on these areas. The China's medical treatment/welfare technologies seem to be clearly still in the stage of needing aids rather than rendering cooperation. However, China has been producing a number of new products in the areas where her traditional arts of medicine are combined with advanced techniques of the West, e.g., those for examination, as felt from a number of the equipment types presented to the China Medical Treatment Equipment Exhibition. (NEDO)

FY 1999 report on the survey of the international joint research project on medical welfare equipment; 1999 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of internationally cooperating in the R and D of medical welfare equipment, visits were paid to Australia and the U.S. to survey the related administration/research institutes/medical welfare facilities. Australia is a world leader of heart (transplant) operation, organ transplant, artificial middle ear, apneic relaxation equipment, ophthalmological equipment, bio-materials, etc. The country wants to positively promote the international cooperation with Japan because both countries are complementary to each other. Starting about 1999, the U.S. entered the age of competition of the R and D with the use of genome, and the post-genome age is already beginning there. A number of ventures are running for creation of new industry. As to the U.S. government's measures taken for subsidy, regulation, etc. toward new industry, the information could be obtained from the persons concerned. The impression of a tour of welfare facilities in the U.S. was that hardware/software are systematically prepared there, and the aged live bright and positive lives and enjoy lives. (NEDO)

1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

FY 1998 annual report on the fourth international forum on environmental catalysis (IFEC 99); Dai 4 kai kankyo shokubai kokusai forum (IFEC '99) 1998 nendo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The 4th international forum on environmental catalysis, held in January 1999 in Chemical Society of Japan's Hall, had a total attendees exceeding 170, including 10 foreign attendees invited. A total of 20 papers (including 10 by foreign attendees) were presented, discussing diversified problems; 3 keynote addresses regarding (to what extent environmental catalyst can contribute); and 5 for the session of catalysts for clean processes, 6 for the session of eco-friendly chemistry, and 8 for the session of environmental catalysts for air pollution. The lectures included (global environmental problems and environmental catalysts) by Prof. Segawa of Sophia University as the opening address; solid base catalysts by Prof. Ono of Tokyo Institute of Technology in the session of (catalysts for clean processes); activation of dioxygen by transition metal complexes-new approach to highly selective catalytic oxidation with molecular oxygen by Prof. Moro-oka of Tokyo Institute of Technology in the session of (Eco-friendly chemistry; and environmental catalysts-present and future as the comprehensive review by Prof. Misono of University of Tokyo in the session of (environmental catalysts for air pollution). (NEDO)

FY 1999 report on the survey of the international joint research project on medical welfare equipment; 1999 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of internationally cooperating in the R and D of medical welfare equipment, visits were paid to Australia and the U.S. to survey the related administration/research institutes/medical welfare facilities. Australia is a world leader of heart (transplant) operation, organ transplant, artificial middle ear, apneic relaxation equipment, ophthalmological equipment, bio-materials, etc. The country wants to positively promote the international cooperation with Japan because both countries are complementary to each other. Starting about 1999, the U.S. entered the age of competition of the R and D with the use of genome, and the post-genome age is already beginning there. A number of ventures are running for creation of new industry. As to the U.S. government's measures taken for subsidy, regulation, etc. toward new industry, the information could be obtained from the persons concerned. The impression of a tour of welfare facilities in the U.S. was that hardware/software are systematically prepared there, and the aged live bright and positive lives and enjoy lives. (NEDO)

Achievement report for fiscal 1999. FS surveys to excavate international joint research seeds; 1999 nendo kokusai kyodo kenky seeds hakkutsu no tame no FS chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The FS surveys to excavate international joint research seeds are intended to promote international joint researches, whereas surveys have been carried out in fiscal 1999 on eight themes covering as wide scope as new energies, resource conservation, energy conservation, environment preservation, functional materials, information communication technologies, and bio-technologies. The eight themes are: researches on energy conservation in petroleum and petrochemical industries by using advanced distillation processes (to develop an internal heat exchange type distillation column, and realize energy conservation exceeding the minimum reflux status being the limitation of conventional energy saving means), researches on treatment of hard-to-decompose chemical substances by utilizing surface reformation by means of discharge, a new process monitoring technology (process tomography), establishment of human immortalization cells due to co-manifestation of mortalin and telomerase and elucidation of their structure, a remote maintenance technology using integrated type sensors, application of new heat resistant plastics to photo and electronic materials, preparation processes of petroleum catalysts utilizing in situ XAFS, elucidation and design of the structure of the ultra-micro metal activation point in the reaction process, and surveys on necessity of developing a continuous and massive separation system of high-level energy and resource saving type using liquid-liquid distribution. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research related to hydrogen gas turbines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu. Suiso gas turbine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper describes development of hydrogen gas turbines from among the comprehensive discussions on hydrogen utilizing subsystems. Hydrogen and oxygen gas turbine cycle has varying optimal conditions of plant efficiency depending on fuel patterns. The regenerative cycle may have the turbine inlet temperature at about 1,000 degrees C. The inlet pressure would be ten and odds atmospheric pressure. It is better to keep the inlet temperature higher in order to obtain high specific power. Reduction of power generation cost in using this plant requires that construction cost be decreased, and the specific power be increased if the plant efficiency (in other words, running cost) is assumed constant. Further development is required on technologies to use higher temperatures and pressures. For that purpose, discussions should be given on material development, structural design, and inspection. Hydrogen gas turbines, which present low pollution depending on combustion methods, have great significance for such social problem as environmental contamination. In terms of economy, since hydrogen gas turbines depend on efficiency and fuel unit cost, the evaluation thereon may vary depending on how well the regenerative gas turbines have been established, in addition to future change in hydrogen price and the technologies to use higher temperatures and pressures. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for aircraft engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Koku engine ni kansuru kenkyu (furoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-01

This paper introduces two out of six theses related to hydrogen fueled aircraft engines presented at the First World Hydrogen Energy Conference held in Miami in March 1976. One thesis mentions several initial prospects related to terrestrial requirements on hydrogen fueled transport aircraft. Liquefied hydrogen is attractive for large long-distance transport aircraft. Its high energy content can reduce the take-off full load weight by more than 30%, enhancing the economic effect of the aircraft. Saving fossil fuels will require national policy decisions in the near future, where introduction of liquefied hydrogen is more advantageous for long-distance aircraft. However, its introduction into wide-body transport aircraft being the major consumer requires transportation companies and airport authorities to carry out joint development with transport aircraft makers and liquefied hydrogen suppliers. The second thesis describes special natures of fuel subsystems for liquefied hydrogen fueled aircraft. Requirements to major fuel system elements and operation characteristics require evaluation as a comprehensive system, rather than as individual component criteria. In addition, hardware, experience and fuel systems as they are now in space development may not necessarily serve for the purpose. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and researches on peripheral technologies (Research related to automotive engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper discusses hydrogen fueled automotive engines. Because hydrogen has a very wide ignition mixture ratio limit for spark ignition engines, very lean combustion is possible without a need of throttling, and thermal efficiency in partial load is high. Thermal efficiency while a car is being driven is reportedly higher by 30% to 50%. Values for CO and CH in exhaust gas are negligible, while NOx is at about the same degree as in gasoline engines, which can be made extremely low during lean burn operation. The spontaneous ignition temperature is higher by about 200 degrees C than that of light oil, which presents difficulty in use for diesel engines. Because of small ignition energy and high combustion velocity, excessively early ignition and reverse ignition can occur easily. Hydrogen would be promising if new manufacturing systems are developed and production cost is reduced, and on the other hand, if petroleum price rises sharply. Hydrogen is also expected as a measure to prevent pollution, including that from soot, odor and CO2. The largest difficulty is in the transportation method, and the only possible method at the present is transportation in liquefied hydrogen form. However, practical application will have such problems as tanks, feeding devices, and cost. Development is desired on light-weight metallic hydrides. Technologies for safety and engine performance must also be developed. (NEDO)

Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Kamimori, K; Sakai, K; Ishihara, O [Kumamoto University, Kumamoto (Japan)

1996-10-27

The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

Empirical analysis of consumer decision making processes on setting up residential photovoltaic systems; Jutakuyo taiyoko hatsuden system no donyu ni kansuru ishiki bunseki

Energy Technology Data Exchange (ETDEWEB)

Iuchi, M; Okawara, T; Tsuchiya, T [Central Research Institute of Electric Power Industry, Tokyo (Japan); Konakayama, A [Tokai Univ., Tokyo (Japan)

1996-10-01

Inquiries are made to consumers (monitors) who own a photovoltaic power generation system at their houses, and their replies are analyzed for isolating the factors involving the purchase of this domestic power generating system. A large part of the monitors are 40-50 years old males in the relatively high income bracket. They are very interested in problems of global environments, resources, and energy, and are inclined to assume value-consciousness and life-style which encourage them to love health and nature, participation in social functions, and decision-making. The need for the protection of global environments occupies more than 90% of the reasons for their adoption of photovoltaic power generation. The monitors strongly feel, however, that they paid very much for the apparatus although they were granted some subsidies. As for motives for their acquisition of the system, their answers are categorized into four groups according to their responses as to whether (or not) they expect economic merits though dependent on future development and whether (or not) they accept the current energy policies. The result shows that some monitors think like average citizens. 17 refs., 22 figs., 11 tabs.

Fiscal 2000 survey report on the survey and research on green technology industry; 2000 nendo green technology industry ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The approaches of the Government and local autonomies to green technologies are surveyed toward the construction of a green technology industry. The present activities and future outlook of environmental industries interested in green technologies are surveyed and examined, the green technologies here including (1) energy conservation measures and development of non-fossil fuels, (2) energy-related and environmental measures for countering global warming, (3) waste treatment measures for countering dioxins and endocrine disrupters. A survey is conducted of the outlines and future trends of green technology related important studies now under way at laboratories and research institutes of universities, the Government, and private-sector corporations. Based on the results of the surveys, important subjects of technical development in green technologies are extracted and studied for the possibility and outlook of their practical application. Tasks to discharge and problems to occur before they are introduced to the market are also evaluated and confirmed. Based on the results of the research and development of green technologies, actualities of environmental industries are taken up, and the problems and tasks to be settled before environmental technologies are introduced to the market are investigated and studied. (NEDO)

Investigation on chemical heat pump using calcium-chloride; Enka calcium no suiwa dassui hanno wo mochiita solar chemical heat pump ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Arai, T; Saito, Y [Meiji University, Tokyo (Japan)

1997-11-25

With an objective of developing a room heating system utilizing a solar chemical heat pump, an experimental system was fabricated to evaluate its performance. Steam was employed as a working gas, and for a reaction material, calcium-chloride was used, which has a reaction temperature zone permitting safe use and fitting the purpose among other hydrate systems and has high standard enthalpy in hydration. Water was used as a solar heat transferring medium. The system operates under the following principle: a container I is filled with hydrated salt and a container II with water, the two containers being linked with a pipe interposed with a valve; heat is inputted and outputted by performing charging and discharging alternately; and the role of a heat pump is played by deriving from environment the heat of water evaporation in the container II during discharging. The COP must take into account the electric power consumption of the water circulation pump to transfer solar heat. A COP of 0.256 was derived as a result of the experiment. 3 refs., 5 figs.

Study on the distribution of streaming potential while groundwater pumping up; Chikasui no kumiage ni tomonau ryudo den`i hassei ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Sato, H; Shima, H; Sakurai, K [OYO Corp., Tokyo (Japan)

1997-10-22

This paper describes effectiveness of water channel prospecting by means of streaming potential method. To investigate the distribution of streaming potential on the ground surface while groundwater pumping up, some laboratory experiments were performed. A system was constructed, in which fluid is flowed in an experimental cistern from its both ends and self-flowed through a strainer pipe fixed for flowing out the fluid at the center of the cistern. Streaming potential with the flowing of the fluid was observed. Positive streaming potential waveform was generated with the flowing of the fluid, and the potential increased with approaching the strainer pipe. A groundwater pumping test facility was used as a field test site. There was a positive maximal point of potential distribution at about 30 m far from the pumping well in the southeast direction. The potential gradually decreased in the eastern part from the maximal point. The potential steeply decreased in the northwest direction from the pumping well. From these experiments, it was found that the groundwater flow and underground structures can be reflected by the distribution of streaming potential, and that the present method is effective for water channel prospecting. 3 refs., 8 figs.

Survey on the construction of realization scenario of large-scale revegetation of arid regions; Daikibo ryokuka no jitsugenka scenario sakusei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In order to fix carbon dioxide as a measure to mitigate global warming, research of large-scale revegetation of arid regions has been conducted toward the ultimate goals of systematizing revegetation technologies centered on securing and using water resources, evaluating the feasibility of arid revegetation by extending the viewpoint to examine even rainfall increase by artificial means, and establishing a strategic program for large-scale revegetation. A trial revegetation feasibility map was made for a selected target region in Western Australia, and rough revegetation steps were formulated. Selection of proper region, introduction of technology, and planning were conducted by grasping environment of the target revegetation region. As a result, it was found that growth of plants is vigorous at the catchment areas due to the surface water transfer along the topography of surface in spite of poor rainfall. Obstruction of plant growth is partly caused by the corrosion of soil and accumulation of salt, but mainly caused by the shortage of water. Based on these data, ranking of proper regions was evaluated. When the technology is introduced in the region with A-rank, several times of water can be collected. 60 refs., 61 figs., 30 tabs.

Survey on chemical engineering technologies for the global environmental protection; Chikyu kankyo hozen no tame no kagaku kogakuteki taisaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

The present paper suggests chief measures to suppress and reduce global greenhouse gases. Under the control of artificial environments such as bioreactor, hydroponics and vegetable factory, a very high fixing rate of CO2 can be obtained, but CO2 generation accompanying electric power consumption is also large. It is preferable to use methane as resource by reforming reactions or selective oxidative reaction. In the recovery technique of fluorocarbon, 100% recovery is desirable. Techniques for decomposing recovered fluorocarbon and converting it to harmless material are the most backward ones. Understanding of essential structural relationship of coal is necessary for establishing combustion technique for the reduction of N2O. The integrated power generation system composed from solid electrolyte type fuel cell and coal-gasifying process, high-performance, superheat pump system form scientific technology imposing no burden on the global environment. Establishment of purification technique for industrial- or living-related drain inflowing to a closed water area system, establishment and reinforcement of inspection system for oil spill in the oceans in a global scale are required. 240 refs., 63 figs., 30 tabs.

Research on elaboration of the action plan for the New Earth 21; `Chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Elaboration of the action plan for the New Earth 21 plan proposed by Japan in Houston Summit was researched. In fiscal 1995 three types of energy supply/demand scenarios, sensitivity analysis under various conditions, and cases presupposing CO2 emission regulations or not were evaluated by analysis toward 2050 using the New Earth 21 Model (NE 21 Model). Energy-saving is important, and CO2 recovery/treatment technology is introduced according to CO2 emission regulations, while attention is focussed on biomass energy. The issue of solar and wind power generation is cost reduction. In a presupposed horizontally integrated energy system, methanol represents an important intermediate energy. As a whole, CO2 reduction can be achieved by various combinations of energy-saving, introduction of regenerative energy, and CO2 recovery/treatment technology. Case studies of the action plan were conducted by unifying the evaluation criterion on coal IGCC, photovoltaic generation and biomass. The NE 21 Model was useful for elaboration of the reduction scenarios of CO2 emission. 26 refs., 84 figs., 28 tabs.

Improvement of prediction accuracy of large eddy simulation on colocated grids; Colocation koshi wo mochiita LES no keisan seido kaizen ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Inagaki, M.; Abe, K. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

1998-07-25

With the recent advances in computers, large eddy simulation (LES) has become applicable to engineering prediction. However, most cases of the engineering applications need to use the nonorthgonal curvilimear coordinate systems. The staggered grids, usually used in LES in the orthgonal coordinates, don`t keep conservative properties in the nonorthgonal curvilinear coordinates. On the other hand, the colocated grids can be applied in the nonorthgonal curvilinear coordinates without losing its conservative properties, although its prediction accuracy isn`t so high as the staggered grid`s in the orthgonal coordinates especially with the coarse grids. In this research, the discretization method of the colocated grids is modified to improve its prediction accuracy. Plane channel flows are simulated on four grids of different resolution using the modified colocated grids and the original colocated grids. The results show that the modified colocated grids have higher accuracy than the original colocated grids. 17 refs., 13 figs., 1 tab.

Study on load levelling by means of the control of air conditioner operation; Kuchoki kado seigyo ni yoru fuka heijunka ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, H. [Hiroshima University, Hiroshima (Japan); Sadakuni, S. [Japan Broadcasting Corp., Tokyo (Japan)

1995-04-20

The recent drastic increase in the number of air conditioners has caused sharp and narrow peaks in summer seasons due to the inherent temperature sensitive characteristics. The authors proposed to reduce the peak power demand by controlling air conditioner operations, verifying its effectiveness on peak demand clipping. However, the former study has shortcomings in that any qualitative treatment of room temperatures or pleasant feeling was not attempted and it did not provide a way of assessing peak demand clipping in a power system as a whole. In this paper, we shall first propose a new control method that can compromise pleasant feeling and reduction in power demand. Although air conditioners are used to pursue `pleasant feeling`, this contradicts to reduce power consumption and further more the concept of `pleasant feeling` is very vague. Hence, `Weber-Fechner`s law` is utilized to quantify the pleasant feeling which is treated as fuzzy quantity. Fuzzy co-ordination method is used to compromise power demand curtailment and pleasantness. In the second part of this paper, we shall propose an approach of assessing the amount of peak load clipping when the newly proposed control strategy is adopted in a real size power system: A decrease in the required generation capacity is estimated provided that the Loss of Load Probability (LOLP) is maintained at the same level before and after the application of the new control strategy. The reduction can be regarded as a dividend of load management. 5 refs., 9 figs., 5 tabs.

FY 1999 report on investigation on establishment of body function database; 1999 nendo shintai kino database no kochiku ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The investigation is made to provide the data which widely cover various characteristics of aged persons for the general designers who design equipment and environments for aged persons. It is found, by the tests for measuring sight and hearing sensations of the aged, that they generally need higher sound to hear; frequency of alarming sound is preferably lowered from 3,000 to 4,000Hz now used for the equipment to 1,000 to 2,000Hz, and the level at which sound can be heard is significantly different from that at which the announcement can be understood. For evacuation order or the like, for example, it is necessary to announce the disaster site and evacuation routes, which the aged hear for the first time, especially slowly and distinctively. The database of body functions of the aged are improved by correcting the problems associated with depth of strata and poor prospects, frequently pointed out by those who look up the data from the daily actions, in such a way that the system can be easily looked at from notices for each function position of the product and also from the related human characteristics. (NEDO)

Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Itagaki, H. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H.; Ito, S. [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M.

1996-12-31

Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

Research on active magnetic levitation of multiple high-T{sub c} superconductors; Fukusu no baruku chodendotai wo mochiita akuteibu jikifujo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishi, K.; Tachi, K.; Sawa, K. [Keio University, Tokyo (Japan); Iwasa, K. [Francis Bitter Magnet Laboratory, Cambridge (United States); Nagashima, K.; Fujimoto, H. [Railway Technical Research Institute, Tokyo (Japan); Miyamoto, T.; Tomita, M.; Murakami, M. [Superconducting Research Laboratory, Tokyo (Japan)

1999-11-25

This paper describes a new [electromaglev] system, in which multiple Y-Ba-Cu-O bulk superconductors are levitated on a DC magnet. In this system, we have succeeded in controlling the levitation height and force like the case of a single bulk system. We also simulated the total levitation force for multiple bulks, which were in good agreement with the experimental results. (author)

Fiscal 2000 survey report. Research on creation of microspheric photonic material; 2000 nendo bishokyu photonics zairyo no sosei ni kansuru kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Experiments were conducted under microgravity for findings on the creation of microspheric photonic materials which are high in sphericity. The experiments were carried out at the fall type microgravity facility of Japan Microgravity Center (JAMIC). In the experiments on the ground surface and under microgravity, glass specimens of 3BaO-97B{sub 2}O{sub 3} mol%, 4BaO-96B{sub 2}O{sub 3} mol%, and 2SrO-98B{sub 2}O{sub 3} mol% were tested. They were heated, melted, and cooled for the on-site observation of phase splitting in them. It was found as the result that, in the case of specimen 3BaO-97B{sub 2}O{sub 3}, the phase splitting start under microgravity was similar to that on the ground surface while the nucleation velocity was lower under microgravity. Specimen 2SrO-98B{sub 2}O{sub 3} mol% exhibited an approximately 0.5-second delay in its phase splitting start under microgravity as compared with its ground surface behavior. As for the nucleation velocity under microgravity, the value was same as that on the ground surface in the first half but, in the second half, it was lower than that on the ground surface. The said approximately 0.5-second delay in the phase splitting start was, when the cooling rate was taken into consideration, attributed to an approximately 6.5 degrees C fall in the phase splitting start temperature, and this suggested that phase splitting was suppressed under microgravity. (NEDO)

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Fiscal 1999 technical survey report. Survey of energy conservation technologies in Japan; 1999 nendo kokunai no sho energy gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

NEDO (New Energy and Industrial Technology Development Organization), in its effort to implement a joint project with importing countries, endeavors to popularize energy conservation technologies by introducing them into plants in the importing countries and by demonstrating their validity on real systems. Energy conservation technologies in use in Japan's steelmaking, cement making, chemical, and oil refining industries were reassessed in view of their usefulness in the above-said project. During the reassessment, they were analyzed also for cost effectiveness for the scales on which they would possibly be introduced. Ninety-four technologies were reassessed, which involved the top pressure recovery facilities, continuous casting facilities, high frequency melting furnace, and high efficiency sintering furnace ignition device, these for the steelmaking industry; the materials crushing vertical roller mill, NSP (new suspension preheater) type cement calcination kiln, finishing process preliminary crusher, urban wastes conversion into materials for cement making or into fuel, these for the cement making industry; the multi-effect evaporator for an ammonia manufacturing process and the device for collecting waste heat at the outlet of a synthetic gas compressor, these for the chemical industry; and reduction in the amount of injection steam by use of vacuum distillation tower top steam recycling, etc., these in relation with oil refining facilities. (NEDO)

Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

1997-10-01

Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

Investigations on an environment friendly chemical reaction process (eco-chemistry). 2; Kankyo ni yasashii kagaku hanno process (eko chemistry) ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to structure a chemical reaction process that does not discharge a large amount of waste by-products or harmful chemical substances, or so-called environment friendly process, investigations and discussions were given based on the results derived in the previous fiscal year. A proposal was made to reduce environmental load on development of oxidized and dehydrogenated catalysts that can produce selectively ethylene, propylene and isobutylene in an oxidation process. In liquid phase oxidation, redox-based oxidation and solid catalyzation of automatic oxidation reaction were enumerated. In acid base catalyst reaction, development of ultra strong solid acid was described to structure no pollution discharging process. In the fine chemical and pharmaceutical fields, the optical active substance method and the position-selective aromatics displacement reaction were evaluated to reduce environmental load. A questionnaire survey performed on major chemical corporations inside and outside the country revealed the following processes as the ones that can cause hidden environmental problems: processes discharging large amount of wastes, processes treating dangerous materials, and processes consuming large amount of energy. Development of catalysts is important that can realize high yield, high selectivity and reactions under mild conditions as a future environment harmonizing chemical process. 117 refs., 23 figs., 22 tabs.

Performance analysis on utilization of sky radiation cooling energy for space cooling. Part 2; Hosha reikyaku riyo reibo system ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Marushima, S; Saito, T [Tohoku University, Sendai (Japan)

1996-10-27

Studies have been made about a heat accumulation tank type cooling system making use of radiation cooling that is a kind of natural energy. The daily operating cycle of the cooling system is described below. A heat pump air conditioner performs cooling during the daytime and the exhaust heat is stored in a latent heat accumulation tank; the heat is then used for the bath and tapwater in the evening; at night radiation cooling is utilized to remove the heat remnant in the tank for the solidification of the phase change material (PCM); the solidified PCM serves as the cold heat source for the heat pump air conditioner to perform cooling. The new system decelerates urban area warming because it emits the cooler-generated waste heat not into the atmosphere but into space taking advantage of radiation cooling. Again, the cooler-generated waste heat may be utilized for energy saving and power levelling. For the examination of nighttime radiation cooling characteristics, CaCl2-5H2O and Na2HPO4-12H2O were tested as the PCM. Water was used as the heating medium. In the case of a PCM high in latent heat capacity, some work has to be done for insuring sufficient heat exchange for it by, for instance, rendering the flow rate low. The coefficient of performance of the system discussed here is three times higher than that of the air-cooled type heat pump system. 8 refs., 5 figs., 4 tabs.

Study on the living environment of semi-underground room with attached green house; Fusetsu onshitsu no aru hanchikashitsu no kyojusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Tsukayama, N [Ochanomizu University, Tokyo (Japan)

1996-10-27

In response to demand for the expansion of living space, the living environment of semi-underground room has been investigated. An attached green house (passive solar house) is adjacent to the semi-underground room. This is reinforced concrete construction, having flat type solar collector on its roof and lighting window in its north side. It does not have artificial air conditioners. Based on the measurements of daylight factor, artificial lighting is not required at the window in the daytime, but it is desirable to use daylight and artificial lighting together at the center. The performance of sound insulation depends on the high performance soundproof sash level. There is less daily temperature variation due to its large heat capacity, and less yearly temperature variation than the outside. By shielding the solar radiation, the insolation in the green house in summer can be restricted in the same as in winter. The insolation can be easily received in winter due to its large vertical intensity of solar radiation. The green house in the south side is useful for improving the living environment of semi-underground room. The temperature rise in the semi-underground room can be restricted by opening window in summer. It is desirable for the comfortable living to use artificial cooling to reduce the daytime temperature by 3 to 4{degree}C. In winter, it is comfortable to heat by 4 to 5{degree}C. 2 refs., 7 figs.

Features of vertical axis wind turbine and development of airfoils sections; Chokusen yokugata suichoku jiku fusha no tokucho to yokugata ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan); Nakayama, H [Oriental Kiden Company, Osaka (Japan)

1996-10-27

Features of a straight wing type vertical axis wind turbine (VAW) and its airfoil sections were studied. The wind turbine in which various aerodynamic work components are mounted on the rotation axis normal to the ground surface is named VAW. Like the airfoil section of aircraft, in lift type VAW, wind turbines were driven by lift 70-90 times as large as drag in some cases. Features of the VAW airfoil section which is a straight wing in plan and a fixed pitch wing (with a fixed angle to a blade support arm) in cross section, and those of wind turbines were studied. Some factors affecting the features, work principle and performance of VAW were clarified. On airfoil sections, products of each weight function and each corresponding aerodynamic factor (lift, drag and pitching moment factors) were plotted on an attack angle ({alpha}) axis. From the conditions for increasing the total sum of areas drawn by the products on the {alpha} axis, various characteristics required for airfoil sections were clarified. Such characteristics nearly agreed between an airfoil section for favorable starting characteristics and that for high efficiency. 3 refs., 7 figs.

Stability analyses of urban water supply systems with wastewater reuse; Toshi haisui no junkan riyo ni yoru mizu kyokyu anteika ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H.; Zhang, S. [Meijo Univ., Nagoya (Japan); Okada, N. [Kyoto Univ., Kyoto (Japan). Disaster Prevention Research Inst.

1995-10-20

Wastewater reuse can be considered as a type of water resource development which is expected to improve the aquatic environment, as well as the stability and reliability of municipal water supply systems. To this extent, wastewater reuse has been taken into account in the planning of water supply systems in several Japanese cities. However, to date the effect of wastewater reuse on water supply system stabilization has not been discussed quantitatively, and the relation between waster water reuse rate and water supply system stability has not been analyzed. In this study, a stochastic model has been presented to evaluate the stability of water supply systems with optimal wastewater reuse rate. Some theoretical analyses and numerical studies were performed, and all of the results have shown that the model is reliable for not only basic studies on water supply system stability, but also for practical use as well. 5 refs., 5 figs., 3 tabs.

Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

2000-10-25

The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

Studies on the friction and wear properties of synchronizer rings and gear cones; Shinkuro kiko ni okeru masatsu mamo tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hayashi, K; Kunoki, T [COSMO Research Institute, Tokyo (Japan)

1997-10-01

The influence of materials of synchronizer rings, automotive gear oils and sulfur-phosphorus EP additives on the friction and wear properties of synchromesh system was studied by using a synchromesh friction tester. As a result, the durability was decreased by using the synchronizer ring made of copper alloys. The initial friction performance estimated by using the synchronizer ring made of resin have influence on EP additives, in particular some kinds of phosphorus type additives. 3 refs., 12 figs.

Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Itagaki, H [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H; Ito, S [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M

1997-12-31

Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

FY 1999 report on the survey of the basic cooperation project of enhancement of the international energy consumption efficiency. Project on promotion of exchanges with the persons concerned with government agencies, etc.; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo, kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Seifu kikan nado kankeisha koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of promoting the understanding of effective energy utilization and constructing corporative relations between countries, the persons concerned with government agencies of India, China, Indonesia, Vietnam, Myanmar and Thailand were invited to Japan, and exchanges of opinions were made on policies, technical development, the state of the introduction, etc. The persons concerned with governments of India, China and Indonesia participate in NEDO Forum 2001 to give lectures on the energy policy of their own. The persons sent from the Vietnamese government paid visits for survey to NEDO, Obayashi Corp., Kawasaki Heavy Industries, Ltd., Mitsubishi Materials Corp. and Taiheiyo Cement Corp. as reference of the model project on cement sintering plant power reduction. The persons sent from the Myanmar government paid visits for survey to NEDO, ECCJ, Chiyoda Corp., Yokogawa Electric Corp. and Cosmo Oil Co. as reference of the model project on energy conservation at fertilizer plant. The persons concerned with the Thai government paid visits for survey to the plants concerned with the model project on residue combustion waste heat recovery facilities at paper mills and the model project on waste heat recovery at steel material heating furnace. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.1). Achievement report on development of novel high-performance dry type desulfurization agent made from coal ash; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.1). Sekitanbai wo genryo to suru shinki koseino kanshiki datsuryuzai no kaihatsu to riyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop a technology of using quicklime instead of slaked lime for a reduction in desulfurization cost, based on the technology of the coal ash utilizing dry type desulfurization device operating on coal ash, slaked lime, and gypsum, as hardened by hydration. Activities are conducted in the three fields of (1) basic study, (2) desulfurization agent bench-scale manufacturing test, and (3) study for putting the technology to practical application. In field (1), the basics are studied of the lime slaking process in the manufacture of a dry type desulfurization agent from quicklime, the mechanism is elucidated of the generation of active desulfurization substances, and effective utilization is studied of the desulfurization agent after use. In field (3), conceptual designs are prepared, cost efficiency of desulfurization systems are evaluated, simplified absorption systems are studied, and the trends of dry type desulfurization systems are surveyed. The cost of desulfurization under development is equivalent to that of the wet type method (limestone-gypsum system) when the used desulfurization agent is discarded, and is approximately 60% of the wet type method when the whole amount is effectively utilized. (NEDO)

Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.10). Achievement report on independent distributed type power generation technology of using now-unused gas pressure difference energy; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.10). Miriyo gas atsuryokusa energy ni yoru dokuritsu bunsangata hatsuden gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Development is under way of a power generation system utilizing pressure difference during fuel gas transportation, independent from the outside and installable in the vicinity of the load. It is assumed that power is supplied to a decompression device in a fuel gas supply pipeline. Fuel gas placed under high pressure in the mainline is decompressed upon arriving at a consumer area. The intended technology of utilizing the now-unused pressure difference will be employed for power generation, and energy will be collected accordingly. Activities are conducted in the three fields of (1) the acquisition of heat sources for heating, (2) the development of technologies for compensating for seasonal and daily load variations on gas or power, and (3) the development of control technologies to cope with emergency. In field (1), a system is developed, independent from external heat sources, to operate on an indirect heating system based on a heating furnace. In domain (2), it is proved that high efficiency system operation will be available if the influence of gas pipeline transportation parameters on load variations is analyzed for the effective utilization of the pipeline operating system. (NEDO)

Report on the FY 1999 feasibility study for the international joint research in the Asian area. 6; 1999 nendo Asia chiiki kokusai kyodo kenkyu kanosei chosa hokokusho. 6

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper surveyed the situation of the recent economic crisis, social circumstances, trends of energy policies, etc. in Asian countries. The energy consumption in Asian countries mainly including ASEAN countries and China is expected to show a large growth hereinafter together with a rapid economic growth on a long-term basis. Further, the harmony with the environmental problem has been requested. This problem is important also to Japan from a viewpoint of the regional response to the stabilized energy supply/environmental problems. The response to global environmental problems in these countries and the promotion of development/spread of new energy/energy conservation are strongly desired. For the spread of these technologies, it is effective to actually construct/operate/maintain plants under the joint research with Japan from viewpoints of personnel training, technology improvement, PR effects, etc. It is helpful also for Japan from the aspect of technology development such as data acquisition. It is necessary to accurately grasp the needs and technical levels of the other country in the case of carrying out the joint research. The survey was made about 7 countries including Thailand, Indonesia, Malaysia, the Philippines, India, China and Vietnam. (NEDO)

FY 1997 Report on New Sunshine Project. International co-operative projects (Australia-Japan solar energy technology cooperation, etc); 1997 nendo kokusai kyoryoku jigyo. Nichigonado taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Described herein are the progresses, memorandum concluded for the new project, NEDO/MUERI project activities, among others, for, e.g., Australia-Japan solar energy technology co-operative project. The photovoltaic cell outdoor exposure test project has been progressing as expected in Australia since FY 1996. The test data have been collected for one year and analyzed successively. The second information exchange workshop is scheduled in June 1998 in Sydney for the thin-film, polycrystalline photovoltaic cell manufacturing technologies. The new type photovoltaic cell long-term exposure test project has been started in FY 1997 as the new project in Oman. The weather conditions of the test site are very severe, very high both in temperature and humidity. The new type photovoltaic cell modules, centered by the amorphous silicon, will be exposure-tested in the severe atmospheres, to verify long-term reliability of the photovoltaic cells. A total of 5 types of the modules are to be exposure-tested; 3 types of 6 amorphous silicon cells, one type of 2 CdS/CdTe cells, and one type of 2 thin-film polycrystalline cells. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Robot control system; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Robot seigyo system

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

R and D of the robot control system was conducted in the following items: 1) integrated open control system, 2) remote control robot manipulation language, 3) human factor robot use built-in LAN system, 4) built-in actuator driver. In 1), there were some problems to be pointed out around the system, but the effectiveness was confirmed as system architecture of each verification item. In 2), development/design were made of RCML(R-Cube Manipulation Language) as a remote robot manipulation language, telecommunication protocol, and the experimental system, and the international standardization was targeted. In 3), the R and D was conducted of the realtime telecommunication protocol which clears the standards for the distributed control required for construction of human factor robot and the advanced realtime micro-controller, ULSI, which is the one that the protocol was made IC. In 4), an intelligent connector for built-in actuator was developed which enables saving of wiring in robot system and plug-in connection. 13 refs., 186 figs., 53 tabs.

FY1998 survey of overseas coal import base arrangement promotion. Survey of the international coal situation; 1998 nendo kaigaitan yunyu kiban seibi sokushin chosa. Kokusai sekitan jijo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper summarized in a fixed form the coal situation of the major coal producing countries (exporting countries) in the world and major European countries. The survey outlined general circumstances, economy/industry/trade, etc. of each country. As to the coal relation, described are coal reserves, production/supply-demand/export, properties of the main brands, the mining industry law, foreign investment control, working custom, etc. In Part 1, the paper selected the following as coal exporting countries: Australia, Canada, China, Columbia, Indonesia, New Zealand, Poland, Russia, South Africa, the U.S., and Venezuela. In Part 2, the paper described coal trends in the main European countries such as France, Germany, the U.K., and Spain, in terms of maps, general circumstances, main economic indexes, changes in imports/exports, imports/exports from/to the main countries, trade configuration by item, recent energy policy and coal policy, changes in coal supply/demand and future, coal-related governmental organizations, etc. (NEDO)

Fiscal 1997 report on a feasibility study of international joint researches in the Asian region; 1997 nendo chosa hokokusho (Asia chiiki kokusai kyodo kenkyu kanosei chosa (4)hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is thought that the energy consumption in Asian countries with ASEAN and China as center will a marked growth also in future together with a rapid economic growth, but harmony with environmental problems and economic growth is being taken as a serious problem. This is an important issue also to Japan from viewpoints of secure energy supply and regional response to the environmental issue. Accordingly, strongly desired is positive response to global environmental issues and promotion in development/spread of new energy/energy conservation in these countries. For the spread of the technologies, actual construction/operation of plants by joint researches with Japan are effective from aspects of personnel raising, technical improvement, PR effects, etc. This is also helpful for Japan in terms of technological development because Japan can also get the unobtainable data from the operation under appropriate conditions. This is a report on the studies of the trends of global environmental problems in Thailand, Indonesia, Malaysia, the Philippines, India and China. 3 figs., 72 tabs.

New energy vision at Sabae City. Toward realization of 'environmental international city'; 2001 nendo Sabae shi chiiki shin energy vision. Kankyo kokusai toshi Sabae no jitsugen ni mukete

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

With an object of accelerating introduction of and uplifting consciousness on new energies at Sabae City in Fukui Prefecture, a new energy vision was put into order based on the result of the initial stage investigation having been performed in the previous fiscal year. Solar light and solar heat energies will be introduced positively into public facilities, and at the same time works will be implemented to accelerate the proliferation thereof into general households. The target of introduction by the year 2010y is set to 2,600 kW by photovoltaic power generation, and the introduction thereof is planned to schools, nursery schools, municipality operated houses, and unattended facilities. With regard to solar heat water warmer, the present proliferation rate of about 7.3% will be raised to 15%. Regarding wastes generated from industrial areas, efficient energy extraction by thermal recycling is intended on the assumption of suppression of wastes generation, their re-use, and recycling. Systems may include the bio-gas system, cogeneration, and recovery of energies from plastics wastes. For acceleration of proliferation of new energies in general, promotion of introduction will be achieved on mini-wind power generation, small hydroelectric power generation, and fuel cell automobiles. (NEDO)

17th Business Report Meeting of New Energy Industrial Technology Development Organization (NEDO). Section Meeting on International Cooperation Projects; Dai 17 kai jigyo hokokukai. Kokusai kyoryoku jigyo bunkakai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

In this section meeting, reports were made on the following themes: 1) pregrinder model project; 2) power recovery model project; 3) energy conservation model project and the importance of the spread. In 1), this model project aims to demonstrate that the electric power unit requirement for cement production can be reduced by installing a pregrinder at the front step of ball mill as the finish process at a cement factory in Indonesia, increasing capacity of ball mill grinding, and reducing operational loads of the ball mill which is large in power consumption. In 2), this project aims to supply China a technology to recover power from high temperature/high pressure exhaust gas via gas expander as electric power of 5.8MW after separating FCC catalyst associated with from the exhaust gas from the generative tower of fluid catalytic cracking equipment for oil refining. To come up to expectations for Japan from neighboring countries in Asia, NEDO Information Center carried out the energy conservation model project, etc. as the international cooperation related project in the energy/environment field. The center is now developing 10 projects. (NEDO)

Report on investigations in fiscal 2000 on the global warming prevention related investigations in cooperative fundamental project of investigating improvement in international energy consumption efficiency. Analysis and comparison centering on cost effectiveness in relation with greenhouse gas (GHG) reduction in Japan; 2000 nendo kokusai energy shohi koritsuka chosanado kyoryoku kiso jigyo chikyu ondanka boshi kanren chosa hokokusho. Kokunai deno GHG sakyugen ni kansuru hiyo tai koka wo chushin to shita bunseki hikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The present investigative research is intended to grasp the whole image of cost effectiveness of the energy saving and new energy technologies to suppress and reduce CO2 emission in Japan. Furthermore, the research considers the cost effectiveness and discusses the efficiency and the directionality of reducing CO2 emission from an estimation of the social introduction cost of individual technologies and quantity of CO2 emission reduction. These activities are intended to provide the fundamental items of information when discussing the measures to achieve the emission reduction target imposed on Japan. The research divides the whole aspect into energy conversion, industrial, consumer and transportation departments for discussion, and calculates the technological items that can be introduced by 2010 and the quantity of the introduction thereof, as well as the effect of reducing CO2 emission. Calculations are also performed on 27 elementary technologies in total and the CO2 emission reducing effect, assuming technological possibilities. Subsequently, analyses are carried out from the viewpoint of cost effectiveness by departments. It is shown that the average cost effectiveness is distributed in the range from 108,000 yen/ton to 1,129,000 yen/ton. Scenarios of reducing CO2 emission are discussed from the analyses of the cost effectiveness. (NEDO)

FY 1999 report on the results of the project supplementary to the New Sunshine Project - Feasibility of coal hydrogasification technology in China. Investigational study of the social adaptability (Feasibility study of the international cooperation - Report of Beijing Research Institute of Coal Chemistry); 1999 nendo New Sunshine keikaku hojo jigyo (Bessatsu, Kokusai kyoryoku kanosei chosa Pekin Bai kagaku kenkyujo) hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu - Shakai tekigo sei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing the coal hydrogasification technology which has a possibility of producing high-quality substitute natural gas in quantity and at low cost, an investigational study of the social adaptability was made. In this fiscal year, the following were carried out: outlook of energy supply/demand in China and the problems, natural gas resource and the plan for the use, actual state of the town gas business and the future plan, etc. As a part of the study, Beijing Research Institute of Coal Chemistry, China Coal Research Institute, made a survey under the research contract. As to the general situation of natural gas in China, report was made on the following: present situation of the development of natural gas resource in China, present situation of town gas in large cities of China, present situation and outlook of coal development and utilization in China, assessment of the coal mine area adaptable to coal hydrogasification, etc. In the survey of the area suitable for coal hydrogasification, report was made on the present situation and future of energy supply/demand in Shanghai, Shanxi, Shenfua and Xinjiang, present situation and future of town gas supply, etc. Survey/report were also made on the coal hydrogasification technology and the applicability. (NEDO)

FY 2000 report on the results of the project supplementary to the New Sunshine Project - Feasibility of coal hydrogasification technology in China. II - Final report. Investigational study of the social adaptability (Feasibility study of the international cooperation - Report of Beijing Research Institute of Coal Chemistry); 2000 nendo New Sunshine keikaku hojo jigyo (Bessatsu kokusai kyoryoku kanosei chosa Pekin Bai kagaku kenkyujo) hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu - Shakai tekigo sei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing the coal hydrogasification technology which has a possibility of producing high-quality substitute natural gas in quantity and at low cost, an investigational study of the social adaptability was made. In this fiscal year, the following were carried out: natural gas resource and the plan for the use in China, actual state of the town gas business and the future plan, etc. As a part of the study, Beijing Research Institute of Coal Chemistry, China Coal Research Institute, made a survey under the research contract. As a result of the survey, the following was found out: In Xinjiang and Urumchi, Uigur Autonomous Region, there is an abundant coal resource that is suitable for coal hydrogasification, the transportation pipeline of natural gas had been constructed, and public facilities are prepared, and therefore, both cities are suitable for the construction of coal hydrogasification plant. Datong, Shanxi Province, is a largest city of coal production, enables the long-term coal supply for coal hydrogasification, and has a plan for remodeling of old facilities and construction of new facilities for the introduction of natural gas, and therefore, the city is suitable for the construction of coal hydrogasification plant. (NEDO)

Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

Achievement report for fiscal 1976 on Sunshine Program. Comprehensive examination of hydrogen-utilizing subsystems and research on peripheral technologies (Survey and research on hydrogen production by quinon method); 1976 nendo suiso riyo subsystem no sototeki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kinonho ni yoru suiso seizoho ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

The quantum yield and conversion efficiency are measured during photosensitized water decomposition at an n-type TiO{sub 2} semiconductor electrode built from a rutile type single crystal, and the role of the TiO{sub 2} electrode is clearly defined. A method is tested of acquiring a photoactive TiO{sub 2} semiconductor as an oxide coating and an oxide coating electrode is fabricated, and its characteristics are determined and then compared with the above-said measurements. A WO{sub 3} semiconductor is manufactured, and its characteristics are compared with the above-said measurements. The mechanism of photosensitized decomposition at a semiconductor electrode is examined, and guidelines are established to follow for improvement on efficiency in semiconductor electrode-aided hydrogen production. Dark and light reactions are caused to occur by adding methyl viologen, potassium ferrocyanide, and potassium ferricyanide, and the photochemical reaction characteristics are clearly defined. Oxygen is generated by use of chloroplast. Use of an acrylamide membrane and an osmotic membrane enables a continuous 48-hour test. A solar beam is concentrated on a TiO{sub 2} electrode for a reaction of Q+H{sub 2}O{yields}QH{sub 2}+1/2O{sub 2}{up_arrow} to occur. A reaction of QH{sub 2}{yields}Q+H{sub 2}{up_arrow} is caused to occur as an electrode reaction. A current of 3.7mA and a voltage of 2.4mV are recorded on a fine day at the beginning of October, and 0.4mA and 0.2mV on a cloudy day. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the hydrogen engine for airplane use); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kokukiyo suiso engine ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This study is aimed at using hydrogen as fuel for airplane engine in the study on the use of hydrogen energy to be made as one of the new energy developments. In the investigational study plan, technical/economical possibilities of the airplane engine using hydrogen as fuel and the airplane carrying the engine are grasped to make the details of the R and D clear by the end of FY 1976. By the end of FY 1974, the actual state in the world of the airplane engine using hydrogen as fuel and the airplane carrying the engine was grasped to make the problems clear. The detailed R and D are as follows. (1) Survey of the actual state of and the problems of the hydrogen engine in Japan and abroad (to be conducted in FY 1974). (2) Consideration of the conceptual design of the potential hydrogen engine, and possibility of the commercialization and prediction of the time of the commercialization (to be conducted in FY 1975). (3) Survey of type, performance, etc. of the airplane carrying hydrogen engine, and the actual economical value and demand (to be conducted in FY 1976). This paper described the results of the survey on hydrogen general and hydrogen use airplane. (NEDO)

Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Research on actualities of Japanese industries' research and development potential); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (Nippon kigyo no kenkyu kaihatsuryoku no jittai ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For working out propositions on what the country should do and on what improvement industries should make for the strengthening of industries' competitive power on the market, analyses were conducted into the objects of research and development, organizations engaged in research and development activities, methods of evaluation, and the like. In concrete terms, studies were made on industries' roles in research and development activities and on the actualities of basic research and development potential, and then a survey was conducted through questionnaires and interviews about (1) tasks relating to corporation management and research and development potential, (2) development of research dedicated talent and its fluidity, and (3) problems feared to get worse in the future. Questionnaires were sent to 217 corporations or 577 people of whom 37.6% responded. Each item is described below. Under item (1), it is pointed out that basic research has shrunk as a whole, that pressure is on the increase urging that research directly increase profit, and that theme selection is made to match the business model. Under item (2), it is stated that post-doctorate researchers' knowledge is respected but that recruitment is another matter, and that fluidity of researchers between corporations will increase. Under item (3), it is pointed out that researchers are increasingly inferior in quality and that brain drain out of Japan is feared. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

Research and development cooperation project on environmental measurement using laser radar in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

As one of the international research cooperation projects, the research cooperation in developing laser radar for environment measurement started between Japan and Indonesia. The project is scheduled to be carried out in a 4-year plan starting fiscal 1993. In fiscal 1993, conducted were negotiations with Indonesia on its implementation and a field survey. Between January 6 and 15, 1994, the first field survey was made in terms of topography, climate, road network and traffic situation of Jakarta city, and the proposed sites for installation were reported. The paper also introduced the reception system on the Indonesian side and a request for technical learning through stay in Japan. The second field survey was conducted between February 27 and March 6, 1994. Indonesia requested that they want to make laser radar observation not only for the local area, but the one that covers industrial areas, central urban areas and residential areas. Incidentally, there was an opinion that it is important to elucidate the pollution mechanism. 19 refs., 43 figs., 6 tabs.

Research and development cooperation project on environmental measurement using laser radar in fiscal 1994; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper outlined activities in fiscal 1994 in the R and D cooperation project on a laser radar for environmental measurement. In the activities in fiscal 1994 of `the ODA laser radar development committee,` the committee held four meetings, two field surveys were carried out, and two researchers were invited from Indonesia. In the field survey, the environment in Jakarta city was investigated in terms of changes in population and number of the cars registered. Further, from data collected during 1994-1998 in the central Jakarta city, the following were made clear: the trend of a decrease in SO2, the trend of a rapid increase and an excess of NO2 content over the environmental standard, the status of pollution of which the level is close to the upper limit of the environmental standard of dust, etc. In the meeting of the policy study for the field survey at LIPI headquarters, Japan proposed a system which is constituted of a difference absorption laser radar, two Mie scattering laser radars, and a central processing unit. The sites proposed were studied in cooperation with Indonesia. 40 refs., 65 figs., 9 tabs.

FY 1996 annual report of investigation on biological fixation of carbon dioxide. 2; 1996 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Various kinds of biological fixation processes of CO2 were evaluated from the various viewpoints. Afforestation of tropical and temperate areas, greening of desert, biomass energy production in these areas by energy plantation, coastal mangrove plantation, fertilization with nitrogen and phosphate to outer ocean and coastal, upwelling zone fertilization with iron, and coral reef expansion combined with OTEC (ocean thermal energy conversion) were comparatively investigated as the selected measures. As a result, the cost of CO2 fixation by cultivation of sea weed and plankton was much higher than that of afforestation. The iron fertilization method which was considered to be one of the high CO2 reduction potentials might be economical. However, its effect could not be quantitatively evaluated. The afforestation of tropical and temperate areas seemed to be most feasible in a short term from the viewpoints of economy and environment. It was suggested that the establishment of a systematic water management technology could make greening and afforestation of desert. 76 refs., 27 figs., 28 tabs.

Fiscal 1994 technological survey report. Research study on polymer materials by precision polymerization; 1994 nendo seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In the paradigm that propelled polymer chemistry, there are involved the establishment of polymer concept, engineering plastics, regulation of higher ordered structure, and precision polymerization. The first two produced the polymer chemistry era in the 20th century. The regulation of higher ordered structure and the precision polymerization are the fundamental technologies supporting the polymer chemistry of the 21st century. The precision polymerization is a technology for regulating the stereospecificity, sequential structure, and molecular weight of polymers by regulating atoms and molecules and is referred to the following important techniques to be concrete. In the precision addition polymerization, stereospecific regulation and purification of active site to give living polymers are required while, in the precision condensation polymerization, regulation of condensation probability process to be secondary Marcov chain is necessary, as is the establishment of non-defect condensation condition avoiding high temperature deterioration and the like. In the biomimetic precision polymerization, key issues are the method of incorporating molecular recognition control and sequential structure control by living organs into an industrial process. If the higher ordered structure can be regulated by the precision polymerization, it is possible to obtain numerous high performance/high functional materials such as superconductors. (NEDO)

Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

Report on an investigation into heat pumps in China in fiscal 1995; 1995 nendo Chugoku ni okeru heat pump system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper surveyed the present status, the status of spread, and the technical development of the technology of heat pumps for residential and industrial uses in China. Main examples of installation of heat pumps are cited below: steam drive absorption type refrigerators in Beijing; sea water heat source turbo heat pumps in Qingdao; hot water drive absorption type refrigerators in Beijing; oil-fueled absorption type water cooling and heating appliances in Beijing; ice latent heat storage airconditioning systems using electrically-driven screw chiller in Beijing; temperature rising systems using electrically-driven heat pump of the solar energy utilization warm water swimming pool in Guangdong Province; cooling water supply using waste heat utilization absorption type refrigerator of the alcohol plant in Shandong Province; timber drying systems using electrically-driven heat pump, and marine product cultivation systems in Quangdong Province; distillation systems using steam turbine heat pump in Jiangxi Province. The demand for heat pumps is expected to be 20 million units under the 9th 5-year plan, and the development of equipment is thought to go toward promotion of energy conservation, low noise, multi-type or multi-functional air conditioning equipment, and computer use. 137 figs., 40 tabs.

Experimental study on the response of very large floating structures (VLFS) in wave; Choogata futaishiki kaiyo kozobutsu no harochu oto ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ota, M; Ikegami, H; Yamaguchi, Y [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1997-10-01

The elastic response of VLFS of 1200m long in wave was studied experimentally using a water tank and integral elastic model of 1/80 scale. As offshore airport, a ultra- thin box type floating structure of 5km long, 1km wide and several meter thick is used, and the effect of elasticity is not negligible for such a structure. The experiment used a water tank of 160m long, 30m wide and 3.1m deep. Supposing a water depth of 20m for real VLFSs, the experiment was carried out mainly in a local shallow water area prepared with a temporary bottom together with that in a deep water area. A simple mooring equipment with a linear spring equivalent to real VLFSs was used. The integral floating model was prepared by not mechanical but welded junction to obtain uniform elasticity. The response in wave showed a complicated 3-D behavior, offering useful data for verification of a behavior estimation method. The response was nearly equal between shallow and deep water areas at the same wave length, and the response amplitude in regular waves was equivalent to the significant amplitude in long and short crested irregular waves. 7 refs., 8 figs., 3 tabs.

Study on estimating fluid force acting on a hull during maneuvering movement; Soju undoji no sentai ni sayosuru ryutairyoku no suitei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yukawa, K; Kijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-01

With types of general cargo vessel and VLCC vessel as the object of discussion, a method was discussed to estimate fluid force acting theoretically on a hull during maneuvering movement, taking frame line shape into consideration. A vortex model was improved by giving consideration of time-based decay on intensity of discrete vortex lines based on the Rankine vortex. Modeling of flow fields around a hull was attempted to deal with movements in which width and draft are small as compared with the ship length, and turning angle speed and deviation angle are small. It was assumed that the ship speed is slow and effects of waves can be disregarded. Specular images of the hull were taken with regard to free surface, and handled as a double body model. Speed potential to express flow fields around a hull is required to satisfy the following five boundary conditions of Laplace, substance surface, free vortex layers, infinity and exfoliation. The potential may be handled as a two-dimensional problem in a field near the hull by using assumption of a slender and long body and conformal mapping. It was found possible to estimate hull fluid force with relatively good accuracy. Fine linear coefficients derived from the estimation were used to have performed highly accurate determination on course stabilization. 5 refs., 6 figs., 2 tabs.

Fiscal 2000 survey report. Basic research on hot molding of amorphous ceramics; 2000 nendo amorphous netsukan ceramics seikeiho ni kansuru kiso kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Experiments were conducted on the plasticity processing of heat resistant ceramics making use of the viscous deformation of amorphous ceramics in the supercooled liquid temperature domain. Concerning the preparation of powder of amorphous ceramics, the plasma rotating electrode method of Institute for Materials Research, Tohoku University, was employed, and a bamboo leaf shaped amorphous flake was successfully fabricated by increasing the arc discharge current. In a search of texture easy to turn amorphous, it was observed that Al{sub 2}O{sub 3}-La{sub 2}O{sub 3} had a supercooled liquid domain of as large as 70K, and this enabled a conclusion that it was a promising candidate for hot molding in a supercooled liquid domain. In an experiment of molding in a supercooled liquid domain, Al{sub 2}O{sub 3}-Gd{sub 2}O{sub 3} was used in a press molding process. As the result, a compact bulk mold was obtained in a temperature domain far lower than in the case of conventional sintering. Crystallization had already advanced in all the molds experimentally fabricated by press molding, and this disabled a study of characteristics to be exhibited by an amorphous mold, but it was found that they had a compressive strength of approximately 1,800MPa. (NEDO)

Coal liquefaction in early stage of NEDOL process 1t/d PSU; 1t/d PSU ni okeru ekika shoki hanno ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ikeda, K.; Kawabata, M.; Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

To investigate the behavior of coal liquefaction reaction in early stage as a part of studies on the coal liquefaction characteristics using NEDOL process 1 t/d process supporting unit (PSU), coal slurry sample was taken from the outlet of slurry preheater located in the upflow of liquefaction reactors, and was tested. Tanito Harum coal was used for liquefaction. Preheater was operated under the condition of pressure of 170 kg/cm{sup 2}, gas flow rate of 64 Nm{sup 3}/hr, and at temperature up to 410{degree}C at the outlet, in response to the standard test condition. The slurry sample was discharged into a high temperature separator with temperature of 250{degree}C. Liquefaction was not proceeded at the outlet of preheater. Solid residue yielded around 80%, and liquid yielded around 15%. Gases, CO and CO2, and water yielded also small amount around 3%. The solid sample contained much IOM fraction (tetrahydrofuran-insoluble and ash), and the liquid contained much heavy oil fraction. Hydrogenation was not proceeded, and the hydrogen consumption was very low showing below one-tenth of that at the usual operation. Hydrogen sulfide gas was formed at early stage, which suggested that the change of iron sulfide catalyst occur at early stage of liquefaction. 1 ref., 5 figs., 2 tabs.

Studies on the utilization of inedible parts produced at processing the marine products. Part 1; Suisan haikibutsu no kodo riyo ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Kitamura, S.; Nomura, A.; Quinones, H. [Industrial Technology Center of Kochi Prefecture, Kochi (Japan)

1995-09-01

For the purpose of effectively using marine products in Kochi pref., analyses were made of the components of the following marine products: the head and inside of frigate mackerel disposed of at the time of producing dried frigate mackerel (an annual catch of the frigate mackerel is about 12000-15000 tons, almost half of which is used for processing for dried bonito), the head and other part of lobster disposed of at lobster restaurants (including the shell of lobster), the skin of lazard fish disposed of in boiled fish paste producing plants. The analysis was conducted in terms of the composition of coarse fatty and fatty acid, free amino acid, ATP related compounds, etc. As a result, the following were found out: in the fat of the head and inside of frigate mackerel, DHA (docosahexaenoic acid) and EPA (eicosapentaenoic acid) were included by 20-30% and 10%, respectively, and the fat is promising as supply source of high-grade unsaturated fatty acid; in the head and other part of lobster, chitin chitosan is included in addition to free amino acid such as glycine and alanine; in the skin of lazard fish, ATP related compounds such as inosinic acid are included, and the skin is useful for a raw material of the seasoning. 15 refs., 4 figs., 6 tabs.

Study on state grouping and opportunity evaluation for reinforcement learning methods; Kyoka gakushuho no tame no jotai grouping to opportunity hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yu, W.; Yokoi, H.; Kakazu, Y. [Hokkaido University, Sapporo (Japan)

1997-08-20

In this paper, we propose the State Grouping scheme for coping with the problem of scaling up the Reinforcement Learning Algorithm to real, large size application. The grouping scheme is based on geographical and trial-error information, and is made up with state generating, state combining, state splitting, state forgetting procedures, with corresponding action selecting module and learning module. Also, we discuss the Labeling Based Evaluation scheme which can evaluate the opportunity of the state-action pair, therefore, use better experience to guide the exploration of the state-space effectively. Incorporating the Labeling Based Evaluation and State Grouping scheme into the Reinforcement Learning Algorithm, we get the approach that can generate organized state space for Reinforcement Learning, and do problem solving as well. We argue that the approach with this kind of ability is necessary for autonomous agent, namely, autonomous agent can not act depending on any pre-defined map, instead, it should search the environment as well as find the optimal problem solution autonomously and simultaneously. By solving the large state-size 3-DOF and 4-link manipulator problem, we show the efficiency of the proposed approach, i.e., the agent can achieve the optimal or sub-optimal path with less memory and less time. 14 refs., 11 figs., 3 tabs.

System approach on solar hydrogen generation and the gas utilization; Taiyo energy ni yoru suiso no seisei oyobi sono riyo system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Hirooka, N; Deguchi, Y; Narita, D [Meiji University, Tokyo (Japan)

1997-11-25

An apparatus is developed to establish a system which allows utilization of hydrogen safely and easily, and its applicability to a hydrogen system for domestic purposes is tested. The system converts solar energy by the photovoltaic cell unit into power, which is used to generate hydrogen by electrolysis of water at the hydrogen generator, stores hydrogen in a metal hydride , and sends stored hydrogen to the burner and fuel cell units. It is found that a hydrogen occluding alloy of LaNi4.8Al0.2 stores hydrogen to approximately 80% when cooled to 20 to 25degC, and releases it to 10% when heated to 40degC. The fuel cell uses a solid polymer as the electrolyte. The hydrogen gas burner is a catalytic combustion burner with a Pt catalyst carried by expanded Ni-Al alloy. The optimum distance between the burner and object to be heated is 22mm. High safety and fabrication simplicity are confirmed for use for domestic purposes. The system characteristics will be further investigated. 4 refs., 8 figs.

Reduction mechanism of dynamic loads on down wind rotor; Furyoku hatsuden system down wind rotor no doteki kaju no keigen kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan)

1997-11-25

Dynamic force on blades in a large wind mill changes with rotational speed for various reasons, such as wind shear that causes vertical distribution of wind velocity or titling angle. Therefore, a 2-blade system on a teetered hub is a practical selection for the coned, down-wind type. Use of teetered axis greatly reduces bending moment in the flap direction and that at the axis of rotation. An attempt was made to understand dynamic loads by inertial force resulting from oscillation of the blade rotating on the teetered axis, and thereby to avoid them. The in-plane load can be diminished to zero when the teetered axis is coincided with the center of gravity, but generally cannot be avoided when the blade is strained significantly, except it is operated at the rated condition. The in-plane load and bending moment can be avoided, when rotational freedom is given around the y axis. Dynamic load on a down-wind rotor can be avoided by use of universal joint. 3 refs., 6 figs.

Research report for fiscal 1998. Research into the recycling of plastic wastes into resources; 1998 nendo hai plastic no saishigenka ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The actualities in Japan are investigated of the types and quantities of plastic wastes, collection and recovery systems, and recycling technologies. Plastic wastes exceeded 9-million tons in 1996, of which 39% was effectively utilized while 61% was merely incinerated or used for reclamation. The 61% of the plastic wastes which are equivalent to oil resources in terms of the energy they contain is found dealt with in such ways, for which additional energy has to be consumed. Some problems are mentioned that occur in the CO2 gas reduction effort in the process of plastic waste recycling for each of its stages of production, distribution, assortment, recovery, and reuse. The problems involve the required reform into production designs and systems with the greatest importance attached to recyclability; share of the expenses between the producing and distributing parties and financial support to assortment/recovery systems; reform of consciousness of both people at large and the administrative organizations, mutual collaboration between them, and reasonable share of expenses between them; construction of a unified assortment/recovery system; expansion of the scope of use of recycled products and the building of environments that encourage their use; diversification of recycling methods and establishment of technologies therefor; and limits on the use of materials and products that generate heavy impacts on environments during their life cycles. (NEDO)

Study on the performance improvement of multiblade fans. Effects of suction cones; Tayoku fan no seino kaizen ni kansuru kenkyu. Suction cone no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kuratani, F.; Ogawa, T. [Hyogo University of Teacher Education, Hyogo (Japan); Yamamoto, S.

1999-07-25

In order to improve the performance of a multiblade fan, the effects of three types of suction cones of the fan casing on the fan efficiency and noise are investigated experimentally. The first type of the suction cone is the insertion type, which is inserted into the inside of the fan impeller. The second type is the extrusion type, which extrudes outside from the casing surface. The third type is the combination type of two types. The results of those three types are compared with those of the commonly used suction cone. The followings are made clear: (1) The insertion type and the extrusion type are effective in improving the efficiency and reducing noise. (2) The optimal lengths of the insertion and the extrusion exist. (3) The combination type is more effective in improving the efficiency. (4) The combination type with the skewed cutoff of the fan casing shows the best effect. (author)

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

1996-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

Report on a survey in fiscal 1999. Survey on movements in technologies related to phytoremediation; 1999 nendo phytoremediation ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey is intended to discuss the status quo in movements of technologies related to phytoremediation (PM) that utilizes metabolic functions of plants, the overseas situation thereof where the PM application has advanced, and the future technological problems. The PM can be divided largely into the following four categories according to the actions of plants: 1) phyto-extraction - absorbs substances dissolved in water directly or through actions of leguminous bacteria to purify the water or soil; 2) phyto-transformation - action to absorb polluting substances into plant bodies and decompose them; 3) phyto-stimulation - rhizospheric microorganisms are activated by enzymes secreted from roots to decompose chemical substances; and 4) phyto-stabilization - actions to fix or stabilize polluting chemical substances by actions of substances secreted from plants and/or leguminous bacteria in soil and interactions with soil particles. Japan's independent researches have derived such researches as a research to utilize street lining trees to purify polluted air, a research to realize purification of hard-to-degrade substances by introducing degradable genes of microorganisms, and a research intended to create plants that accumulate in them heavy metals densely. (NEDO)

FY 2000 report on the results of the research study of environmental information network; 2000 nendo kankyo joho network ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research study on environmental information network formation. The Internet is experiencing an explosive increase in volume of information distributed therethrough. This is accompanied by increased problems related to information searches, information exchange security and information-reliability guarantees. First in demand are excellent portal sites, and second are sites that can be relied on to responsibly provide information. Cooperation with the real world off the Net is of particular importance, because the operating organizations, e.g., sites, will lose their raison deter, unless they clarify their unique abilities and characteristics under the tendencies towards broadened bands and ubiquity. The public sector, on the other hand, is highly reliable, accumulates a large volume of information, and has high network capacity. It has various functions, e.g., supporting the activities pertaining to ISO standards, and promoting the activities, e.g., those for educational programs, interdisciplinary exchanges by researchers, and matching of various organizations. The international cooperation for environmental information needs construction and operation of the networks, and construction of the infrastructures in the developing countries. If information becomes more ubiquitous, a chaotic sea of information will result. NEDO is strongly obliged to serve as the beacon, because it has established a huge volume of environment-related technologies, information, and networks. (NEDO)

Evaluation report on research and development of an ultra-advanced processing system. 3; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

This paper describes comprehensive evaluation on the following technologies as the ultra-advanced processing system: (1) large output excimer laser, (2) high-density ion beam, (3) an ultra-precision machining device, (4) ultra-advanced processing, (5) measurement and evaluation, and (6) comprehensive test. In the item (1), research and development was performed on such technologies as output increasing, output stabilization and beam formation, having achieved the targets. In the item (2), research and development was performed on such technologies as beam convergence, plasma control, ion transportation, high-frequency quadruple pole acceleration, and large-capacity class ion beam, having achieved the targets. In the item (3), research and development was performed on form creation and ultra-precision machining, having achieved the targets. In the item (4), research and development was performed on formation of high function thin films to apply the laser abrasion process to large area, ion surface modification, wide band area optics, high reflectance optics, ion injection, dynamic mixing, and modification of ultra high-grade metal surface, having achieved the targets. In the item (5), research and development was performed on high-accuracy roughness measurement, shape measurement, optical property evaluation, a wavelength meter, ultra advanced processing standard measurement, and environment correction technology, having achieved the targets. In the item (6), comprehensive demonstration was carried out on the component technologies. (NEDO)

Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

Survey on the scrap iron and steel recycling in Thailand and Indonesia; Hatten tojokoku (Tai Indonesia) ni okeru tetsu scrap saiseiyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes the survey results of the scrap iron and steel recycling industries in Thailand and Indonesia. The purpose of this survey is to extract problems obstructing the scrap iron and steel recycling, to recognize the present situation and predict the future situation, and to examine the possibility of international cooperation. As a result of the survey, it was found that the quality of scrap collected in the domestic market is poor as it contains too many impurities for it to be utilized for the manufacture of many higher quality iron and steel products. The actual quantity of domestically collected scrap is too low to support the expected growth in demand in each nation. Current environmental management practices are largely concerned with the construction of wastewater treatment facilities and the extraction of furnace dust. However, the lack of enforcement of environmental regulations does not encourage companies to implement sound environmental practices. Neither government actively promotes and investigates iron and steel recycling in the domestic, commercial or industrial sectors. Collaboration with overseas nations having more advanced iron and steel industries could be helpful to the scrap recycling industry in both nations. 6 figs., 21 tabs.

Study on soot particle formation and oxidation in DI diesel engine; Chokufunshiki diesel kikan ni okeru susu ryushi no seicho sanka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kurata, K; Senda, J; Fujimoto, H [Doshisha University, Kyoto (Japan); Asai, G [Yanmar Diesel Engine Co. Ltd., Osaka (Japan)

1997-10-01

To clarify soot formation and oxidation process in diesel combustion, the natural emission of OH radical and the flame temperature were obtained in the combustion chamber of D.I. diesel engine. Further, soot were detected by LII (Laser Induced Incandescence) and LIS (Laser Induced Scattering) technique to assess the relative soot diameter and its number density. OH emission and flame temperature were compared with data of soot diameter and number- density. The results show that : (1) OH emission has relation to flame temperature. (2) OH emission arises latter than soot emission, because early soot at early combustion consume OH to oxidate. (3) As soon as it is ignited, soot particles are formed in the region of low temperature. 6 refs., 7 figs., 2 tabs.

Report on a survey in fiscal 1999. Survey on movements in technologies related to phytoremediation; 1999 nendo phytoremediation ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey is intended to discuss the status quo in movements of technologies related to phytoremediation (PM) that utilizes metabolic functions of plants, the overseas situation thereof where the PM application has advanced, and the future technological problems. The PM can be divided largely into the following four categories according to the actions of plants: 1) phyto-extraction - absorbs substances dissolved in water directly or through actions of leguminous bacteria to purify the water or soil; 2) phyto-transformation - action to absorb polluting substances into plant bodies and decompose them; 3) phyto-stimulation - rhizospheric microorganisms are activated by enzymes secreted from roots to decompose chemical substances; and 4) phyto-stabilization - actions to fix or stabilize polluting chemical substances by actions of substances secreted from plants and/or leguminous bacteria in soil and interactions with soil particles. Japan's independent researches have derived such researches as a research to utilize street lining trees to purify polluted air, a research to realize purification of hard-to-degrade substances by introducing degradable genes of microorganisms, and a research intended to create plants that accumulate in them heavy metals densely. (NEDO)

Study on the detached house plan using of a maximum natural energy. Part 1; Shizen energy fukugo riyo no keikaku ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Wada, I; Mino, M; Miyata, T; Okawa, M [Nihon University, Tokyo (Japan)

1996-10-27

The geographical position or environment is set on the assumption that the natural energy of a detached house is used in a hybrid state. Moreover, the energy consumption of the house and the natural energy supply obtained from the geographical position were compared and investigated. As a result, the energy consumption is 10,617 kWh, and the energy supply is 8,236 kWh. About 78% of the whole consumption can be theoretically made from natural energy. The energy supply is calculated on the low side during prediction. Therefore, an increase in the energy supply is expected by installing a solar collector based on solar energy, expanding the solar panel area, and increasing the number of wind mills. However, this energy is partially lost via an inverter while it is supplied to the general domestic equipment. At the six main points in Tokyo and its districts, the adaptability of natural energy used based on the regional characteristics is investigated presently and the installation of a system is examined. 13 refs., 2 figs., 6 tabs.

Fiscal 1994 survey report. Survey of environmentally friendly chemical process (Ecochemistry); 1994 nendo kankyo ni yasashii kagaku hanno process (ecochemistry) ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Processes that contain latent environmental problems are the massive generation of wastes (inorganic salt, acid catalyst, base catalyst, and huge quantities of wastewater), handling of dangerous substances (use of hydrogen fluoride, use of phosgene, and use of substances whose discharge is legally controlled), processes which consume much energy (circulation of quantities of raw materials, use of quantities of solvents, separation of products with difficulties, use of high pressure, and multiple stage reaction), and processes which are expected to use resources now remaining unexploited. As an element technology for the solution of problems, there is the development of a solid redox catalyst for liquid phase oxidation. As compared with a liquid phase homogeneous catalyst, it discharges less inorganic wastes, facilitates the separation, recovery, and treatment of inorganic salts, corrodes structural materials less, and is thermally stable. An alkane partial oxidation catalyst when developed will achieve more energy conservation than an alkene oxidation catalyst. In relation to acid/base reaction, the zeolite catalyst will be improved and ultrastrong acids and ultrastrong bases will be developed, and these will reduce wastes, mitigate corrosion, and facilitate product separation. The development of a process is also expected which will avoid the use of toxic phosgene. (NEDO)

Fiscal 1995 research investigation on chemical process technology using supercritical fluid; 1995 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the supercritical fluid utilization technology, conducted in fiscal 1995 were collection of basic data, extraction of R and D subjects and survey/analysis of application fields based on the literature survey and overseas field survey. From the research results, the following were selected as research subjects: as to the clean/recycling process technology, non-selection cascade treatment process of mixed waste plastics, hazardous waste treatment process, and radioactive waste treatment process. As to the unused resource utilization process technology, the supercritical submerged combustion power generation process, heavy hydrocarbon resource reutilization process, biomass synthetic utilization process, and carbon dioxide reutilization process. As to the next generation reaction process technology, the simple reaction process, de-organic solvent process, chemical materialization process for methane, and reaction separation combined process. As the innovative material process technology, the plastic forming process, high-functional materials, high-efficiency energy conversion materials, and heightening of function of solid wastes. 537 refs., 116 figs., 54 tabs.

Research and development cooperation project on environmental measurement using laser radar in fiscal 1995; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of contributing to the environmental management in Indonesia, Japan made R and D of a laser radar to measure the urban air pollution and an environmental network jointly with Indonesia in compliance with the actual situation of the country. At present, in developing countries, air pollution is becoming a big problem because of increases in population and in energy consumption in urban areas according to the industrial/economic growth. As for the laser radar, it is an active sensor with laser as light source and can observe in high resolution the three-dimensional space distribution such as density and composition of air pollutants. Japan is a leader in the development of laser technology which is a core technology for the laser radar and the preceding research. The equipment is installed at several points of urban areas in Indonesia, and at the same time, the observation network is constructed to collect, analyze and process data at the central processing center. This is a 4-year plan from fiscal 1993 to 1996. In fiscal 1995, negotiations with Indonesia and field surveys were conducted to determine sites for installation. A plan for system improvement was also decided on. 38 refs., 24 figs., 14 tabs.

On the estimation method of hydrodynamic forces acting on a huge floating structure; Choogata futai ni hataraku haryoku ryutairyoku no suiteiho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kagemoto, H.; Fujino, M.; Zhu, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

A floating structure such as an international airport is anticipated to have a length of about 5,000 m and a width of about 1,000 m. A singular point method may be used as a method to estimate force that such a floating body is subjected to from waves. In order to derive a solution with practically sufficient accuracy, 1250 elements are required in the length direction and 250 elements in the width direction, or a total of 312,500 elements. Calculating this number of elements should use finally a linear equation system handling complex coefficients comprising 312,500 elements, which would require a huge amount of calculation time. This paper proposes a method to derive solution on wave forces acting on a super-large floating structure or fluid force coefficients such as added mass coefficients and decay coefficients at a practically workable calculation amount and still without degrading the accuracy. The structure was assumed to be a box-shaped structure. Strengths of the singular points to be distributed on each element were assumed to be almost constant except for edges in lateral, oblique and longitudinal waves. Under this assumption, the interior of the floating structure excepting its edges was represented by several large elements to have reduced the number of elements. A calculation method proposed based on this conception was verified of its effectiveness. 2 refs., 25 figs., 3 tabs.

Leading research in fiscal 1996. Research study on advanced measurement/analysis technology; 1996 nendo sendo kenkyu. Kodo keisoku bunseki gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For development of production technologies suitable for environment, safety and advanced information-oriented society by improving the flexibility of production lines, some new measurement technologies were researched. Problem solution was attempted by combining the in-situ multi-dimensional measurement technology capable of easily obtaining various 3-D information with the non-contact photon measurement technology superior in operability and sensitivity under any environment conditions. This solution requires a compact radiation source with higher brightness and wider spectral range, and a high-sensitive detector. The technology concentrating photon onto minute regions, high-efficiency transmission, and control technology of photon wave front are also necessary. Development and international standardization of a common interface is unavoidable. In addition, its network is essential for advanced use of multimedia,. In the future, the comfortable life surrounded by advanced products and multimedia, comfortable social environment, safety and resource saving will be achieved by this technology. 94 refs., 75 figs., 15 tabs.

Report on the cooperative study of technology to collect valuable resources in brine; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reported on the research, design, and evaluation on a system to recover by sedimentation magnesium from the brine in the salt manufacture by solar evaporation in Mexico, and a system to recover by adsorbent lithium, boron, etc. from the brine of the solar pond salt field in China. In the case of Mexico, an overall recovery system was developed, but in the evaluation of economy of the system, it cannot be said that the system is feasible even if assuming that the required fresh water can be secured. It was found out that the economical efficiency largely depends upon the cost of hydrated lime and the selling price of magnesia clinker. In the case of China, a plant for production of 500 tons/year of lithium carbonate was conceptually designed to evaluate the economical efficiency. As a result, the internal profitability of the plant is not so high, approximately 6%, though continuously profitable during the operation of 15 years. It was indicated that the project was not economically very efficient. 164 figs., 44 tabs.

FY 1974 Report on results of Sunshine Project. Feasibility study on digging high-temperature beds; 1974 nendo koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-31

The desired target geothermal conditions for which the digging equipment is to be developed are 3,000 to 5,000 m as depth, 400 degrees C as temperature and 500 kg/cm{sup 2} as pressure. As the first phase, the study is conducted on feasibility of development of techniques for digging high-temperature beds under a temperature condition of 250 degrees C, where the rotary table type digger is mainly studied. It is most widely used for digging oil wells as well as geothermal wells. The current rotary table B type digger is studied as the equipment serviceable at 250 degrees C as the target temperature level for the moment for digging high-temperature beds. The studied items include the problems involved in the digger body, pipes, bits and other members, and also measures to expand its possibility. Also studied/surveyed are applicability of the new digging techniques now under development to geothermal wells, and techniques for fracturing high-temperature rocks. This report summarizes to help select the methods desired to be developed in the future, and plan development of the digging systems. (NEDO)

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T; Hayashi, S [Osaka University, Osaka (Japan). Faculty of engineering

1997-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

FY 1998 annual report on the survey report on possibility of international joint researches for Asian countries. 5; 1998 nendo Asia chiiki kokusai kyodo kenkyu kanosei chosa hokokusho. 5

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are results of surveys on dissemination policies for, and development trends in, energy saving and new energy areas in 6 Asian countries, Thailand, Indonesia, Malaysia, the Philippines, India and China. Possible joint research themes for Indonesia include effective utilization of palm oil residue, modernization of distribution systems, high-efficiency coal-fired thermal power generation techniques, and promotion of dissemination of solar cells. For Malaysia, renewable energies, e.g., photovoltaic power, will be developed to promote electrification for those areas not well electrified. The Philippines is positively receiving technical and financial aids for new energy and energy-saving areas from the advanced countries. India is considering to introduce a number of projects for, e.g., technological optimization of power supply area, decentralized power generation, oil exploitation and extraction techniques, and photovoltaic power generation. China is still in the preliminary stage in its energy research and development, and will need further joint researches in the energy sector. (NEDO)

FY 1998 international cooperation project for global environment/project to evaluate influence of climate change; 1998 nendo chosa hokokusho. Chikyu kankyo kokusai kyoryoku jigyo/kiko hendo eikyo hyokanado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the international cooperation for the global warming problem, evaluation/study were conducted on policy to lessen climate changes from viewpoints of scientific technology, environment, and economy/society. In the development of evaluation methods on cost analysis, the following were pointed out: Changes in resource utilization brought about as a result of the policy are all needed to be numerated; In resource, clean air and water, and also abolition of price barrier and prices now in force are included. As subjects on the technology transfer, cited are barriers in aspects of organization/system and barriers in aspects of economy/finance and society. Especially, it was pointed out that it is necessary to exchange the persons concerned in the industrial sector. Of various optional policies toward the prevention of global warming, the Kyoto mechanism not only has an economical merit of the use of low cost option but can be fairly promising from an environmental viewpoint of internationally controlling the greenhouse effect gas emission, if the characteristic of practically using the market can be so designed that it fulfills its function. (NEDO)

Fiscal 1999 international engineer exchange project (Coal mining technology field). Overseas workshop (Australia); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Goshu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the technology exchange with Australian coal mining engineers, the technical levels and needs on coal production, safety and environment in Australia, and the FS result on transfer of Japanese technologies, engineer exchange and joint research in a coal mining technology field. The overseas workshop (Australia) was held on Nov. 9, 1999 (Tues.) in Brisbane, Queensland. The Australia-Japan Technology Exchange Workshop on coal resources and coal mining technology includes 5 sessions (keynote address, trends and issues of coal resource development, coal resources and production technology, coal resources and safety technology, coal resources and environmental problems), and the open forum discussion on innovative technologies for coal mining. 6 Japanese specialists and 11 Australian specialists read papers. After the workshop, the participants visited Liddell Mine in New South Wales to master natural conditions, and production and safety technology levels of Australian coal mines, and to exchange various information with Australian coal mining engineers. (NEDO)

Fiscal 1998 engineer interexchange project (coal mine technology field). International interexchange project (Workshop in Japan); 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya). Kokusai koryu jigyo (kokunai workshop)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the workshop and technical tour held in Japan for technical interexchange of domestic and overseas engineers. From the information obtained, the higher productivity of coal mines is dependent on selective mining under blessed geological conditions, however, basically establishment of an advanced management technique for inexpensive stable operation. Both preliminary collection of geological information and introduction of advanced facilities even under unstable conditions are necessary. The balance and optimization of the whole system, and an excellent human nature for operation are also essential. Use of roof bolt supports is diffusing as improvement technology of excavation speed and roof control technology over the world. However, for introduction of new technologies, collection of test results and various kinds of training are necessary. Methane gas in coal seams as the main theme of the Hokkaido workshop is a precious unused natural resource, and important for prevention of global warming and coal mine protection measures. Its use is dependent on development of gas drainage technology. (NEDO)

Promotional operation for developing industrial technologies for global environment in fiscal 1998. International research exchange operation; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective of creating a new scope of study intended of solving global environment problems and structuring a new technical system, exchanges with overseas researchers and research institutions have been carried out subsequent to those in last year. In fiscal 1998, six researchers from different countries were invited to implement joint researches, and two overseas researchers were invited to an international conference on industrial technologies for global environment. In addition, in order to identify trends of research and development in overseas countries, two researchers were sent to universities in Germany and the U.S.A., and three researchers to international conferences and symposiums on the industrial technologies for global environment. It was intended to exchange technological information between overseas researchers and Japanese researchers who are performing the advanced researches on the industrial technologies for global environment, and to proliferate the latest items of technological information. Therefore, seven international seminars have been held, including the '98 Japan-China Global Environment Protection Symposium, 'substance migration and carbon circulation in coral reefs', 'plant bio-technologies in the 21st century', and the Fourth International Forum for Environmental Catalysts. (NEDO)

Fiscal 1999 technical achievement report. Development project on international standards for developing new industry (Comprehensive research); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development of 13 individual subjects whose achievements are expected to come into use on the international scale was started in fiscal 1998, to be completed in three years. Progress is reviewed for each of the subjects, and the findings are mentioned below. Research and development is progressing smoothly, specifications to be internationalized have been narrowed down, and it is now foreseen that the main points of the specifications to be presented will be successfully prepared. There are some subjects, however, about which it is difficult to specify to which technical committees they are to be submitted. Assistance, for instance supply of information, by technical committees involved is indispensable. The attitude toward international standardization taken by European and American business corporations visited for study by Japanese researchers is to be disseminated to Japanese business corporations since the information thus collected will help them. Although 75% of the 13 subjects have reached a level where they may be presented as specifications for international standardization, yet they need active support by organizations concerned and research of trends of internationalization-related institutions before they are actually accepted as international standards. (NEDO)

Promotional operation for developing industrial technologies for global environment in fiscal 1998. International research exchange operation; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective of creating a new scope of study intended of solving global environment problems and structuring a new technical system, exchanges with overseas researchers and research institutions have been carried out subsequent to those in last year. In fiscal 1998, six researchers from different countries were invited to implement joint researches, and two overseas researchers were invited to an international conference on industrial technologies for global environment. In addition, in order to identify trends of research and development in overseas countries, two researchers were sent to universities in Germany and the U.S.A., and three researchers to international conferences and symposiums on the industrial technologies for global environment. It was intended to exchange technological information between overseas researchers and Japanese researchers who are performing the advanced researches on the industrial technologies for global environment, and to proliferate the latest items of technological information. Therefore, seven international seminars have been held, including the '98 Japan-China Global Environment Protection Symposium, 'substance migration and carbon circulation in coral reefs', 'plant bio-technologies in the 21st century', and the Fourth International Forum for Environmental Catalysts. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on a hydrogen utilizing subsystem and research on peripheral technologies (Research on peripheral technologies for hydrogen); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper describes research on peripheral technologies for hydrogen. For the cost of manufacturing hydrogen from different primary energies, coal gasification could be the lowest at the present time. In the nuclear power field, the thermo-chemical method and the water electrolysing method may be assumed, but they depend greatly on future technological development. Particularly the water electrolysing method is dependent on electric power cost. In the hybrid method, hydrogen is obtained from electrolysing reaction with water of sulfur dioxide derived by paralyzing sulfuric acid (oxygen is also generated). The method requires two forms of energies, heat and electric power, whereas combination with a very high temperature reactor (VHTR) is being discussed as a heat source. This method may not be said greatly more advantageous than the direct water electrolysis, but may have future possibility. Hydrogen manufacturing utilizing living organisms is an interesting matter in terms of science and engineering, with a large number of research achievements beginning to appear. Expectation is drawn on the mechanism based on co-work of photosynthesis and a hydrogen generation system, alga and bacterium strain search, separation, cultivation, and applied research and development. Research is also under way to obtain hydrogen by converting photo-energy by using an electrochemical photo-cell utilizing semiconductor electrode to electrolyse water (color sensitizing) (NEDO)

Fiscal 2000 survey on electrical power supply system for the purpose of reducing greenhouse effect gas. Three scenarios for spread of distributed power generation by 2010; 2000 nendo onshitsu koka gas sakugen no tame no denryoku kyokyu system ni kansuru chosa hokokusho. 2010 nen made no bunsangata dengen fukyu ni kansuru mittsu no scenario

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An examination was conducted concerning the course of spread of distributed power generation (on-site power generation of 2,000 kW or less) by the year 2010, with three scenarios prepared. In the scenario 1, the government will completely deregulates the power market and take no other steps, leaving the matter to market competition. The universal service will be abandoned, which means higher power prices for remote regions, contributing to the spread of home power generation. In the scenario 2, the government, having reached the limits of the nuclear propulsion policy, will adopt natural gas as the center of its electrical power policy, providing preferential treatments such as subsidies and tax exemptions and requesting the power companies to increase their usage. This will lead to higher transmission charges, with distributed power generation more advantageous to the IPPs in terms of cost. In the scenario 3, environmental awareness will make increase in the capacity quite difficult including power generation facilities and transmission/distribution network, and will invite a power crisis in the long run through insufficient capacity in power generation and transmission/distribution volume. Distributed power generation requiring no reinforcement to the grid will spread such as household-use type without system interconnection, solar cells or small fuel cells. (NEDO)

FY 1998 report on the results of the technology development on the integration of nerve information; 1998 nendo shinkei joho togo ni kansuru gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This R and D aims at developing the interface system including 2D multipoint high density electrode elements which measure and analyze the information processing process of cranial nerves at high speed and in minute detail. The R and D were carried out on the following 4 subjects: 1) development of 2D high density multipoint electrode; 2) development of alignment/bonding technology; 3) development of technology for existence maintenance/activation of nerve cells; 4) study of performance evaluation and applicability of the system. In 1), an electrode is developed in which the high density multipoint platinum electrode was built on glass substrate, and the following are conducted: making a pattern of alignment of this electrode, making the shape of electrode 3D, and technical development of surface composition. In 2), the following are developed: technology to align cells on the patterned electrode element correctly and technology to bond cells on the element for a long time. In 3), the following are developed: functional materials to hold living nerve cells/nerve systems on the electrode element for a long time, nutrition system, and technology to monitor the state of cells/systems on the substrate. In 4), conducted are the evaluation of performance of the developmental system and the applicability to the screening in nervous function molecular search, etc. (NEDO)

Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

Report for fiscal 2001 investigations on energy saving assistance institutions in different countries; 2001 nendo kakkoku no sho energy shien seido ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Taking up China, India, Indonesia and Thailand as the object, investigations were performed on political financing measures that can be used for installing energy saving facilities, and on applicable preferential taxation systems that are applied in each country. Indonesia has no aid measures such as subsidies and political financing directly purposed for energy conservation. Import duty exemption is applied for the purpose of promoting investments. Three kinds of funds are available through IFCT to implement fund aid to protect the environment. Energy saving fund has been established as an energy saving policy to provide subsidies. Energy saving machineries recognized by the investment committee are exempted from the import duties. India has no political financing measures directly purposed for energy conservation. Its preferential taxation system for energy conservation includes the 100% accelerated amortization system for energy saving machineries and facilities, and the preferential import duty system. In China, the financing from the China National Development Bank is considered utilizable in installing energy saving facilities. The country has no aid measures in the taxation system, but fund aid and subsidy by supplementing interest are provided. (NEDO)

Study on low permeable backfill materials. Backfill materials for waste disposal facilities; Koshisuisei juten zairyo ni kansuru kenkyu. Hoshasei haikibutsu shobun shisetsu eno tekiyosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, F; Konishi, M; Shiraishi, H [Okumura Corp., Osaka (Japan)

1994-11-15

A discussion was given on the fundamental properties of mortar made from cement mixed with silica fume. Four kinds of silica fumes with different particle size distributions were used. The following results were obtained: distribution of pores in mortar admixed with silica fume shifts to the smaller radius side; while the admixture increases the compression strength in mortar, the increasing trend varies depending on the kinds of silica fumes; this is thought to be caused from the difference in pozzolan activity between silica fumes; and the strength increase is caused by densification of the structure due to the pozzolan reaction that is generated after hydration, or in other words, decrease in the pore volume. The applicability of the mortar was investigated as a filling mortar to fill up clearances between wastes. It was found that the filling performance can be controlled by mixing silica fume at an adequate level and adjusting the viscosity. The diffusion coefficient for the admixed concrete is smaller by 30% to one digit than that for the ordinary concrete. High-performance water stopping concrete of 0.11 {times} 10{sup 4}cm {sup 2}/s at maximum was obtained. The concrete can be regarded as a material having superb filling and water stopping performances. 6 refs., 4 figs., 5 tabs.

Research report on the trend of preventive measures against global warming by substituting CFCs; Daitai freon no chiku ondanka taisaku doko ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper reports the research results on the present state and future trend of protective measures for the ozone layer, and the trend of preventive measures against global warming by substituting CFCs such as HFC, through international conferences, meetings and lecture meetings, and literature survey. In the 8th meeting of the parties to the Montreal Protocol, it was presented that refrigerator producers in Thailand phased out CFCs from their products earlier than the schedule in cooperation with Japan. The final draft including the approval of essential use from 1997 to 2002 was reviewed, and reported to the technology/economy assessment panel. Reduction of ozone depleting substances was guided in Thailand, Indonesia and Philippines. The latest trend of substituting technologies of HCFC was surveyed, and the control trend of F-containing greenhouse effect gas emission was also surveyed through the conference of the parties of climate change in fiscal 1996. Based on the IPCC report in 1995, the emission amount of greenhouse gases of nearly 10% in contribution such as CO2, methane and fluorocarbon was arranged. R and D on destruction of CFCs was also surveyed. 35 refs., 54 figs., 32 tabs.

Basic survey on the residence using hybrid energy in snowy cold regions; Sekisetsu kanreichi ni okeru hybrid energy katsuyogata jutaku nado ni kansuru kiso chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The conceptual model and feasibility of the hybrid energy system for residences and public facilities in snowy cold regions were studied. Based on the existing data, the existing and available amounts of natural energy and unused energy in the target area, Sapporo were estimated. Based on the predicted energy demands of 4 kinds of building models, the energy systems for such models were studied. The use of the following energies was considered: photovoltaic power generation and solar heat for all the models, household sewage energy for the multiple-dwelling house model, and wind power generation for the public facility model. The annual energy balance was calculated to evaluate it. The use of additional commercial electricity was necessary, while surplus solar heat energy was found in summer which can push up the self-sufficiency rates of the residence and public facility models to 70% and 44%, respectively. The multiple- dwelling house model which can use a large amount of household sewage energy could utilize 80% of new energy, while the other 3 models utilized only 60-70% of that. 81 figs., 42 tabs.

FY 1997 survey report on information sharing product life-cycle systems. 2; 1997 nendo joho kyoyugata product life cycle system ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Highly value-added products considering a total life-cycle of products by integrating both production and consumption activities are much in demand, and each information corresponding to each product should be realized by concept integrating both information and product as common element. Survey was made on what a social system integrating production and consumption should be, a product information model, and technology integrating both information and product for raw material, industrial machine and household appliance as examples. An information model shared by the whole production and consumption activities was first prepared. Based on this model, data storage, update, retrieval and dispatch technologies were surveyed and developed for life-cycle systems. Degradation and life sensing technology was surveyed for maintenance, repair and disposal activities using proper unstable information of each product. A support system for use of shared information was developed to promote a new highly value-added function. Total evaluation was made on information sharing product life-cycle systems. 10 refs., 23 figs., 7 tabs.

Properties of board made from wood powder with phenol-formaldehyde-powder resin; Mokufun wo genryo to shita board no seizo to zaishitsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, S.; Yamada, M. [Shizuoka Univ., Shizuoka (Japan). Faculty of Agriculture

1998-04-15

The purpose of this study is to acquire fundamental knowledge about the factors for production and the physical properties of boards when wood powder is used as the main material and powder adhesive is used as the binder in the formation of wood boards under heat and pressure. The effects of temperature for pressing, specific gravity of board, and the ratio of adhesive on bending strength, internal binding force, and size and stability against moisture are investigated. The temperature behavior at the central area of boards under heat and pressure shows similar tendency of stagnation near 140degC which increases thereafter irrespective of the temperature of the hot plate in this experiment. The bending property increases linearly when the resin content is low, and shows the tendency of leveling off gradually when the resin content is larger than 20%. Linear relation with specific gravity if obtained in the 0.6 to 1.0 specific gravity range. Wood powder boards have high internal size stability in the thickness direction than ordinary wood boards. 13 refs., 11 figs.

Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-05-01

This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

Fiscal 1999 survey report. Basic survey on practical application of innovative energy technologies; 1999 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey aims to verify whether recoverable energies can bear the important role of energy source in place of fossil fuels, to probe into problems that may arise in the process of recoverable energy introduction, and to compile suggestions about measures toward their smooth introduction, these by working out an 'ultralong-term world energy supply and demand outlook' valid up to 2100. Various measures to deal with global warming are analyzed by simulation. The study is not to predict what is in store but to metrically describe and present choices and possibilities for the future with a theoretical consistency based on various factors including economic growth, population, demand for energy, magnitude of fossil energy resources, and feasibility and cost of recoverable energies. This study implies that there is not a single, determining policy for solving the global warming problem and that it is important to cope with the problem by resorting to combinations of various means. (NEDO)

Fiscal 1996 investigational research on the chemical process technology using supercritical fluids; 1996 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Importance was studied of making a research on the chemical process technology using the supercritical fluid. As for its effect on global warming, the amount of CO2 emission was compared during the operation between the conventional process and the process using the supercritical fluid, the CO2 reduction rate and amount were trially calculated, and a CO2 reduction of a several ten thousand ton scale in carbon conversion was predicted. As to hazardous materials and the reaction of waste retrieval, it was made clear that the process using the supercritical fluid was valid also for objects for which the chemical process used to be impossible, which indicates a possibility of the widening field of application. Concerning its effect on the energy conservation, energy reduction of several ten thousand tons in heavy oil conversion was predicted by replacing all the existing processes with supercritical fluids. Relating to the recycling, with the use of supercritical fluids, the process is possible which produces higher quality and yield and fewer unnecessary products such as char than the conventional process. 197 refs., 102 figs., 71 tabs.

Fundamental study on the melting process of crushed ice in a heat storage container; Chikunetsu sonai ni takuwaeta saihyo no yukai ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yanadori, M; Kobori, H [Hitachi, Ltd., Tokyo (Japan); Tsubota, Y [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1998-03-25

This report deals with heat transfer in the melting process of crushed ice filling in a ice/water heat storage container. Volumetric heat transfer rate and melting end-time are measured when rectangular-type, small-stone-type and particle-type ice in the container are melted by circulation hot water. Melting end-time of small-stone-type ice is the shortest and that of particle-type ice is the latest. Volumetric heat transfer rate of small-stone-type ice and rectangular-type ice is larger than that of particle-type ice. The flow rate of circulation hot water throwing in container through a inlet pipe influences remarkably on heat transfer rate. 4 refs., 10 figs.

Report on investigations and studies on development of materials for hydrogen absorbing alloys; Suiso kyuzo gokin no zairyo no kaihatsu ni kansuru chosa kenkyu hokokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper describes investigations and studies on hydrogen absorbing alloy materials and the technologies to utilize them. In the investigations and studies, literatures were collected and put into order, questionnaire surveys were performed and analyzed, lecture meetings and panel discussions were held, and the discussion results were summarized. In the present status of developing hydrogen absorbing alloys, the current status of and problems in developing such hydrogen absorbing alloys as Ti-based, Mg-based, and rare earth-based alloys were put into order. Discussions were given on prospects of possibilities of developing new alloys, making them amorphous, and putting them into mass production. In the current status of developing the utilizing technologies, such technologies as hydrogen storage systems and heat pumps were put into order and discussed. With regard to problems in hydrogen absorbing alloys, discussions were given on alloy weight, pulverization, activation, heat conductivity, and alloy costs. In discussing the safety, discussions were given on the safety and compliance with related laws and regulations relative to hydrogen transportation using a great amount of hydrogen absorbing alloys, their storage, and heat storage systems. In addition, questionnaire surveys were carried out with an objective to identify the status of developing hydrogen absorbing alloys and needs from the industries. (NEDO)

Research cooperation in the development of laser radar for environmental measurements. Environmental network; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku. Kankyo network

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Among the research cooperation in the development of laser radar for environmental measurements with Indonesia between FY 1993 and FY 1996, results of the research and development of the environmental network are summarized. For the environmental information network, the Tokyo NOC is linked as an Internet connection point in Japan with the Jakarta NOC using an international dedicated line with a capacity of 64 Kbps. The Tokyo NOC is linked with domestic environmental information researchers using Internet. Thus, data stored in the data processing system of laser radar can be exchanged, information in both countries can be exchanged using E-mail, and data can be accumulated. For the research cooperation with Indonesia, research of path control and information relay server, research of effective transmission of data on the network, and research of multimedia communication have been conducted. The multimedia communication, distributed processing, and extension of dedicated line network using PPTP have been also conducted. 39 figs., 4 tabs.

Survey on the technological development issues for large-scale methanol engine power generation plant; Ogata methanol engine hatsuden plant ni kansuru gijutsu kaihatsu kadai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Based on the result of `Survey on the feasibility of large-scale methanol engine power generation plant` in fiscal 1992, concrete technological development issues were studied for its practical use, and the technological R & D scheme was prepared for large-scale methanol engine power plant featured by low NOx and high efficiency. Technological development issues of this plant were as follows: improvement of thermal efficiency, reduction of NOx emission, improvement of the reliability and durability of ignition and fuel injection systems, and reduction of vibration. As the economical effect of the technological development, the profitability of NOx control measures was compared between this methanol engine and conventional heavy oil diesel engines or gas engines. As a result, this engine was more economical than conventional engines. It was suggested that development of the equipment will be completed in nearly 4 years through every component study, single-cylinder model experiment and real engine test. 21 refs., 43 figs., 19 tabs.

Wayfinding and sense of direction with regard to metal representations. ''Hokokan'' no hoji narabini daigae keiro tansaku ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funahashi, K. (Osaka University, Osaka (Japan). Faculty of Enigneering)

1991-07-30

Two kinds of typical environmental learning methods(direction and distance learning and route learning) were conducted experimentally as methods of environmental cognition in unfamiliar areas. Then, aspects of maintaining the sense of direction in grasping space structure of the area environment as well as concrete alternative wayfinding behaviors considered to be behavioral indexes for cognitive mapping were investigated. At the starting point, instruction related to the direction was given to P group, and that related to the route was given to M group. As a result, both groups decided the direction or found the alternative route according to the obtained information. The P group decided the direction properly by grasping the whole directional relations of the area and space structure of the route there. However, it was difficult for them to find the alternative route after restructuring the relations between specific points of the route. Concerning the motor relevant representation of the M group by time-dependent understanding of the route, continual occurence of perceptual characteristics on the way was worth noticing. 13 refs., 8 figs., 6 tabs.

Report on the surveys in fiscal 1999. Surveys on practical application of the research achievements; 1999 nendo kenkyu seika no jitsuyoka ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A number of technological hurdles exist in the process of practically applying the fundamental researches, wherein risks for private business entities to promote the technological development are not at all small. The present surveys are intended to elucidate the actual status as to how a practical application process for technologies is positioned in the series of research and technological development activity floats by private corporations, and what kinds of problems are present, to serve for discussing the way the future supportive environment improvement should be. The 'practical application processes' in private corporations were put into order and analyzed, using as the base the existing study results relative to technological innovation mechanisms. Investigations ere performed on the existing Japanese research and technological development supporting institutions for the practical application processes employed by the private corporations. The result was used for reference of discussing the problems therein. Furthermore, it is indicated that, in the R and D strategies in the U.S.A., profitability is placed as the largest target by means of strengthening the linkage between research and commercialization. This has resulted in decline in the fundamental researches, for which discussions are developed currently. This paper reports investigations on the actual status of business enterprises in the practical application processes. (NEDO)