Study on individual care in nursing home. Part 2. Studies on social welfare institution for the elderly from the aspect of dwelling; Koreisha kyoju shisetsu ni okeru kobetsuteki kaigo ni kansuru kosatsu. Sumai toshiteno tokubetsu yogo rojin home no arikata ni kansuru kenkyu 2

Energy Technology Data Exchange (ETDEWEB)

Inoue, Y.; Otaki, K.; Ohara, K. [Yokohama National Univ. (Japan)] Toyama, T. [Tohoku Univ., Sendai (Japan)

1998-06-30

This study pays attention to the relation between individual care and residents` activities in the social welfare institutions for the elderly (nursing homes) and aims to clarify the influence of building environment (nursing home as dwelling place) on individual care. Behaviors of care staffs and residents are surveyed in four nursing homes. The results of the analysis of the survey are as follows: The care staff`s activities are influenced not only by physical environment and also by the residents` activities. A single bed room is more effective than a multi-bed room for individual care. The small care unit is effective in building plan if the number of staffs is enough. The personal care activities which constitute the greater part of the care activities depend on the location of the residents. It is important to pay attention not only to arrange the common space but also how to use the common space. Spatial structure is required the consideration of the relative position of not only care rooms and resident rooms but also of care rooms and the space used by residents. 7 refs., 14 figs., 7 tabs.

Mechanism of spark generation from Japanese toy firework (senko-hanabi). ; Structural-Oxidizing reaction of micro graphite crystals in molten K sub 2 Sn. Senko hanabi no jikkenteki kosatsu. ; Yoyu K sub 2 Sn chu no sekiboku bikessho no kozo teki sanka hanno

Energy Technology Data Exchange (ETDEWEB)

Ito, H. (The University, of Tokyo, Tokyo (Japan))

1991-12-20

Considerations were given on the spark generating mechanism of graphite particles in molten salt polysulfide through experiments on Japanese sparklers. The firework composition mixed consisted of two kinds: KNO{sub 3}, S, amorphous carbons, charcoal and lamp black, and K{sub 2}CO{sub 3}, S, charcoal and lamp black. The main constituent in fire balls is molten salt polysulfide. The O{sub 2} generated from combustion oxidizes C and S, whereas the generated K{sub 2}CO{sub 3} reacts with S to produce K{sub 2}Sn. In the KNO{sub 3} system, the calorific power reaches the maximum with lamp black contained at 10-15%. This is thought because the K{sup +} expands the space between the graphite crystal layers making the oxidation to take place more easily into their inner sides. On the one hand, the calorific power reduced with the lamp black at more than 16% would be because the lamp black clogging the crystalline spaces restricting the oxidation. It is thought that condensation and decomposition of micro graphite crystals occur simultaneously in the fire balls. It is also believed that the micro graphite crystals jumped out as a result of gas pressure from inside the crystals generated with the progress of oxidation break off at once because of the resistance of air together with the effect of the K{sup +} in the salt polysulfide (mutual separation of each layer). 9 refs., 6 figs., 1 tab.

Experimental study on high strength concrete. 1. ; Basic properties of high strength mortar using various kinds of admixtures. Kokyodo concrete ni kansuru jikkenteki kenkyu. 1. ; Kakushu konwazai wo shiyoshita kokyodo moltar no kihonteki seijo

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T; Uenishi, T; Hayashi, Y [Okumura Corp., Tokyo (Japan)

1990-10-09

The paper studies effects of various powders as admixtures used for high strength concrete of approximately 800-1400 kg/cm {sup 2} compressive strength with the use of mortar. The following are the results of the study: In order to obtain the required table flow values, high performance AE water reducing agent must be increased with an increase of a mixing rate of silica fume (SF). However, in case of mixing blast furnace slag powder or classified fly ash (SLG or FA), AE water reducing agent can be slightly decreased, with an increase of the mixing rate. In order to obtain the required amount of air, in case of mixing SF or FA, AE agent is needed to be more increased than in case of plain mortar, while AE agent is of the same quality as in the plain one. Besides, both compressive strength rate and drying shrinkage rate show characteristic behaviors according to kinds of admixtures and mixing ratio. 10 figs., 5 tabs.

Seismic tomography inversion in the case that sources and receivers are distributed out of a 2-D plane; Shingen jushinten ga nijigen heimennai ni nai baai no danseiha tomography kaiseki ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Yokota, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Rokugawa, S; Matsushima, J [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Ashida, Y [Kyoto University, Kyoto (Japan). Faculty of Engineering

1996-10-01

In the case where sources and receivers are not distributed on a 2-D plane, seismic tomography inversion was studied. In tomography experiments, the existing wells are generally used. In such case, sources and receivers are frequently not distributed on a 2-D plane. The 2.5-D analysis method including 2-D structure and 3-D ray-tracing was thus developed. This method is featured by less memory necessary for ray-tracing calculation, and the same algorithm for velocity determination as 2-D analysis method. In previous methods, since analysis is generally carried out by projecting sources and receivers on a certain assumed 2-D plane, it can derive correct results in the case of constant velocity and straight ray, however, in the other case, it derives incorrect results. Application of 3-D tomography requires a large amount of memory, and falls into poor convergence because of various parameters. The 2.5-D analysis method can avoid these demerits. This analysis method was applied to the data obtained in Ogiri area, Kagoshima prefecture. 5 refs., 3 figs., 2 tabs.

Experimental investigation of PV modules recycling; PV module recycle no jikkenteki kento

Energy Technology Data Exchange (ETDEWEB)

Unagida, H; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Sakuta, K; Otani, K; Murata, K [Electrotechnical Laboratory, Tsukuba (Japan)

1997-11-25

Recycling, cost/energy analysis and recovery experiment were made on crystalline silicon PV modules with EVA(ethylene vinyl acetate)-laminated structure. The life of modules is dependent not on performance deterioration of PV cells themselves but on yellowing or poor transmittance of EVA caused by ultraviolet ray, and disconnection between cells by thermal stress. Recovery is carried out in 3 stages of cell, wafer and material. Recovery in the stages of cell and wafer results in considerable reduction of energy and cost. The recovery experiment was carried out using PV module samples prepared by cutting the modules into 25times15mm pieces after removing Al frames from the used modules, peeling back sheets and cutting off EVA. Since a nitric acid process at 70-80degC can dissolve EVA effectively, it is promising for reuse of surface glass and PV cells as they are. This process is also carried out under a condition around room temperature and pressure, contributing to cost reduction and energy saving for recycling. Generation of harmful NOx is only a problem to be solved. 2 refs., 6 figs., 1 tab.

Effect of operating methods of wind turbine-generator system on net power extraction under wind speed fluctuations in fields; Hendo fukyoka deno doryoku chushutsu kara mita furyoku hatsuden system no unten seigyoho ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Wakui, T. [Japan Society for the Promotion of Science, Tokyo (Japan); Hashizume, T.; Ota, E. [Waseda University, Tokyo (Japan). School of Science and Engineering

2000-01-25

The effect of operating methods of wind turbine-generator system on net power extraction under wind speed fluctuations is discussed in relation to the dynamic behavior of the system. The system is composed of a Darrieus-Savonius hybrid wind turbine and a load generator. In this paper, two types of operating method are examined; constant tip speed ratio operation for stand-alone power systems (Scheme 1) and synchronous operation for utility power systems (Scheme 2). The computed results of the net extracting power using our dynamic simulation model show that the dominant factor of power extraction in Scheme 1 is the dynamic characteristics of rotational components and that it is important to select the appropriate rated wind speed in Scheme 2. Thus, it is concluded that a conformable operating method and rated power output of the system exist for each wind condition. In particular, small-scale systems, which are smaller than approximately 10 kW-system range, are desirable to be operated under a constant tip speed ratio as stand-alone power systems. (author)

Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Kamimori, K; Sakai, K; Ishihara, O [Kumamoto University, Kumamoto (Japan)

1996-10-27

The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

Some considerations on special spacers with damping device for suppressing wake galloping in tandem cables of cable-stayed bridges; Heiretsu cable yo gensui kino tsuki supesa no gensui fuka tokusei ni kansuru 2,3 no kosatsu

Energy Technology Data Exchange (ETDEWEB)

Yoneda, M. [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology] Setouchi, H. [Kawada Industries Inc., Osaka (Japan)

1998-03-20

Cable vibration called wake galloping appears on cable-stayed bridges with parallel arranged cables and its suppression is an important problem. Various methods have been proposed for spacers with damping device for suppressing wake galloping in tandem cables of cable-stayed bridges. But, comparison of damping performances of various methods have not been discussed sufficiently. This paper deals with a type in which dampers are equipped on the midway of the tandem cables through the spacer jig and a type in which dampers are equipped on each surface of the tandem cables to generate shear deformation between them and circular spacer jig moiety and complex eigenvalue analyses are carried out on the two types with changing center spacing and diameters of the cables. The results clarify the relation between the structural damping characteristics and the cable spacing and the effect of torsional rigidity of the cables and also clarify of damping characteristics of the two types. 16 refs., 14 figs., 4 tabs.

Investigation on the dynamic response and strength of very long floating structures by beam modeling on an elastic foundation; Dansei shishojo no hari model ni yoru chodai futai kozo no doteki tawami kyodo tokusei ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

1997-08-01

A very large floating structure was replaced with the beam on an elastic foundation to examine the response characteristics in waves. Another evidence was regularly and numerically given for the basic characteristics of a very large floating body Suzuki found. New information was also obtained. The frequency response is mainly classified into a wave number control area and proper frequency control area when buoyancy elasticity exists. When the buoyancy structure is long and flexible, the proper frequency becomes continuous and the frequency control area becomes a resonance area. In the wave number control area, the Suzuki`s characteristic wave number becomes a control parameter, and various characteristic values are indicated by characteristic wave numbers. The response in the wave number control area becomes quasi-static when the distribution mass of buoyancy is fully small. The design in which the distribution mass of buoyancy is fully large must be avoided. In the displacement amplitude, the mass on the free end is severest. The proper frequency of vertical vibration relatively moves to the high-frequency side when buoyancy is considered as an elastic foundation. Attention must be thus paid to the proper frequency of vibration on the horizontal surface. 9 refs., 12 figs., 3 tabs.

Primary production and calculation in coral reefs. 1st Report. ; Theoretical consideration on changes of CO2 system in seawater. Sangosho seibutsu gunshu no kiso seisanryoku to sekkaika. 1. ; Kaisuichu no tansankei hendo ni kansuru rironteki kosatsu

Energy Technology Data Exchange (ETDEWEB)

Kudo, K [Japan Marine Science and Technology Center, Kanagawa (Japan)

1993-09-30

This paper describes an algorithm for calculating the equilibrium state of carbonate system in seawater. The photo-synthesis, respiration, and basic production ability of organic and inorganic carbon compounds by calcification of coral reef ecosystem and the change in carbonate system in seawater were discussed. The carbonate system in seawater can be estimated by determining two variables among the four variables, i.e., pH value, total carbonate, total alkalinity, and partial pressure of carbon dioxide (PCO2). The analysis program proved to give good agreement with the previously calculated results. In the inorganic production of carbonate in seawater, one mole of carbonate precipitation liberates approximately 0.6 mole of CO2 into the air, and the pH value shifts toward acid side. The experimental value (0.55) for production speed ratio of inorganic carbon to organic carbon in the seawater where the coral family is abundant brings about the increase of the organic carbon production, resulting in the decrease in PCO2 in seawater and the increase in pH value. It is assumed that it becomes of a sink of CO2 in the atmosphere. 23 refs., 3 figs., 7 tabs.

Cultural observations on the history of wheels; Sharin no rekishi no bunkashiteki kosatsu

Energy Technology Data Exchange (ETDEWEB)

Tsuboi, Y [Koyo Seiko Co. Ltd., Osaka (Japan)

1997-10-01

Since primitive times, mankind has been involved in the field of tribology through the use of sliding, rolling, rotation and similar types of motion. Various devices have been used to perform such motion, and in this lecture I will trace their history from the rollers used in ancient Mesopotamia to aid in pulling sleds to the wheels used on chariots and other vehicles throughout history until modem times. I will offer my observations on the role technology related to such rollers and wheels has played in the world`s cultures and discuss the necessity of studying technology from such a viewpoint. 11 refs., 7 figs.

Study on heat collector of the solar system utilizing outdoor air. Experimental results in cases of cold and warm regions; Gaiki donyushiki solar system no shunetsubu ni kansuru kenkyu. Kanreichi to ondanchi ni okeru shunetsu jikken to kosatsu

Energy Technology Data Exchange (ETDEWEB)

Komano, S; Ebara, Y [OM Solar Association, Shizuoka (Japan); Wada, H [Wada Building Constructors Co. Ltd., Hokkaido (Japan)

1996-10-27

An experiment on heat collection was made in the heat collector of a solar system utilizing outdoor air in cold and warm regions. In this system, outdoor air is heated by the air circulation layer on the roof exposed to solar radiation. The heated air is supplied to the object space for heating and ventilation. In the experiment in a cold region, the heat collection characteristics can be adjusted by putting a baffle plate in the air duct according to the experiment of a glass heat collector. The heat collecting air layer on only the iron roof may leak or freeze in the region subject to coldness or heavy snowfall. Therefore, preheat forms the space of a garret, and the preheat temperature comparatively becomes low. The data in which the heat collection characteristics can be adjusted using only a glass heat collector is required corresponding to the regional situation. In the experiment in a warm region, an experiment was made inclusive of the preheat for which outdoor air is absorbed at the eaves. As a result, the heat collection characteristics of preheat were improved. Moreover, a heat collection temperature of about 60{degree}C was obtained on the heat collection surface including the preheat. 1 ref., 12 figs., 3 tabs.

Sea bottom gravity survey of Osaka bay and its study; Osakawan kaitei juryoku chosa to sono kosatsu

Energy Technology Data Exchange (ETDEWEB)

Komazawa, M [Geological Survey of Japan, Tsukuba (Japan); Ota, Y; Shibuya, S; Kumai, M; Murakami, M [Japex Geoscience Institute, Inc., Tokyo (Japan)

1996-05-01

This paper reports a sea bottom gravity survey conducted with an objective to identify deep underground structure in the vicinity of the epicenter of the Hyogoken-Nanbu Earthquake. The surveyed areas are the whole Osaka Bay area north of the north latitude of 34 degrees and 20 minutes, and the eastern part of the Sea of Harima east of the east longitude of 134 degrees and 40 minutes, excluding the areas difficult of performing measurements. A square lattice with sides each about 2 km was arranged with 408 measurement points. The measurement was carried out by using an observation vessel mounted with a sea bottom gravimeter made by LaCoste and Romberg Corporation, which was lowered down to the sea bottom at the measurement points. Errors in positions and water depths at the gravity measuring points were suppressed to less than 0.002 minutes and 0.1 m, respectively. The measurement data were given necessary corrections by using a unified method applicable also to land areas, and a Bouguer anomaly chart was prepared. Based on the chart, this paper summarizes features in the Bouguer anomaly in the surveyed areas (such as the low-gravity anomaly band extending the central part of the Osaka bay from north-east to south-west, and the gradient structure existing on the Awaji island side). 6 refs., 1 fig.

Experimental study on solar desiccant cooling system. 2nd Report; Taiyonetsu kudo desiccant cooling system no jikkenteki kento. 2

Energy Technology Data Exchange (ETDEWEB)

Tanaka, H; Funato, H [Fukuoka Institute of Technology, Fukuoka (Japan); Kuma, T [Seibu Giken Co. Ltd., Fukuoka (Japan)

1996-10-27

Study has been made about a desiccant cleaning system using solar heated water for regenerating the dehumidifier. A dehumidifier and evaporation coolers are combined to attain a synergistic effect in dehumidifying and cooling the air in the house. The simultaneous control of humidity and temperature, however, is quite difficult. Under the circumstances, an evaporation cooler was removed from the outdoor air intake side, to leave a humidifier alone for the control of humidity only. In addition, the length of the dehumidifier was reduced into half for saving fan driving power and for downscaling the model. With only one evaporation cooler in operation that is installed at the exhaust side, the cooling effect is diminished by half. For dealing with the situation, ultrasonic atomization is performed at the exhaust side evaporation cooler for the improvement of the air cooling effect for the next sensible heat exchanger (intake side). The return air is heated by the solar heater water (approximately 60{degree}C hot), regenerates the dehumidifier, and then exhausted. The atomization process elevates the cooling effect, and the resultant cooling effect was as high as that expected from a 2-cooler setup. The dehumidification effect, however, lowers a little. Exclusion of the atomization process will enhance the dehumidification effect, but will reduce the cooling effect as well. 3 refs., 8 figs., 3 tabs.

Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H.; Yoshida, K. [The University of Tokyo, Tokyo (Japan)

1996-12-31

A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

Consideration on the dynamic behavior and the structural design of large scale floating structure. 2nd Report. Stability of elastic structure and design of elastic response; Choogata futai no kozo kyodo oyobi kozo sekkei ni kansuru kosatsu. 2. Dansei henkei wo koryoshita fukugensei oyobi kozo oto no sekkei

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H; Yoshida, K [The University of Tokyo, Tokyo (Japan)

1997-12-31

A policy of improving a very large floating body was planned based on its dynamic characteristics, and a proposal was made thereon. Furthermore, discussions were given on stability that considers effect of elastic deformation required when a structure is mounted on a floating body. With respect to a structural design of a very large floating body in which elastic response is governing, and upon modeling the very large floating body into an aeolotropic plate on an elastic supporting floor, it was shown that the existing range of natural vibration speed in the elastic response is in higher range than the natural vibration speed of heave. It was also indicated that the peak height of response to waves in resonance is inversely proportional to wave frequency, and furthermore, degree of flowing in of vibration energy during the resonance is determined by an inner product of spatial vibration patterns of wave force and the excited mode shape. A proposal was made on a floating body improved of excessive response in the floating body edges by changing the characteristics of the floating body edges. In addition, discussions were given on stability that considers elastic deformation of a floating body that becomes necessary when a structure, such as a building, is built on a very large floating body. 9 refs., 9 figs., 3 tabs.

Study on cobalt oxide; Sanka kobaruto ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

This is No.91 report of National Institute for Research in Inorganic Materials, concerning cobalt oxide. For the growth of single crystal by the Czochralski method, shape of interface and contamination of impurities are affected by the convection of molten liquid in the atmosphere. Various oxides besides CoO were investigated. Solid solutions of Cr2O3 and Al2O3 into CoO were also studied. Non-linear optic and dielectric properties of single crystals, such as Ba2NaNb5O15 and LiNbO3, were examined. It was considered that the positive electron having positive electric charge can be used for the study on the negative electric charge defect in materials. However, the positive electron itself is rare, which results in the too low efficiency of measurement. Efficiency improvement of 50 times was achieved by introducing a high performance 2D position detector, which was still low efficiency of one-hundredth compared with photoelectron spectroscopy. It was found that the aggregation structure of positive ion defects in CoO is a misunderstanding of phenomenon caused by the electronic state in bulk crystals. As a result of the study on the optical properties of f-electron transition metals, transparent ceramics with addition of various rare earth ions were described. 162 refs., 106 figs., 14 tabs.

Studies on silicon nitrides; Chikka keiso ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Sinters of silicon nitrides have excellent properties as a structural material, but their technological repercussion effect is not as much as has been expected. The cause is in insufficient understanding on the mutual relationship between microstructures and mechanical properties. Therefore, methods of controlling structures were first discussed in the studies on synthesis of high-tenacity ceramics. In order to achieve high reliability in material strength, discussions were given on means to have a structure developed with high reproducibility. Development was performed on {beta} powder which shows no abnormal grain growth and is stable at elevated temperatures. Then, quantitative evaluation was made on factors to manifest a self-compounding structure with columnar particles grown in ultrafine particles. The relationship between its chemical composition, microstructure and mechanical properties was also discussed. Particle shapes of silicon carbides and their fracture tenacity values were considered theoretically by using a drawing model. To evaluate the microstructure, it is important to determine the grain boundary composition, whereas an electric field radiation type high-performance electron microscope was developed. In discussing the fracture mechanism, a model was structured for behavior of covalent binding crystals against external stress. 164 refs., 95 figs., 10 tabs.

Study on apatite compounds; Apataitokei kagobutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

To clarify the material properties of apatite compounds, the synthesis method, and the evaluation of physical properties of material and elementary technology were investigated. For the study on synthesis and crystal growth, a method of precipitating calcium phosphate on the surface of metal was investigated by means of relatively mild electrolytic method using liquid phase system. A new molding method of Ca defective apatite was established. Composite similar to vital bone was prepared by means of a new low-temperature sintering. For the study on chemical properties, from the model experiments, it was found that the self-organizing phenomenon, which is observed in the composite of apatite and collagen, happened between the organic single molecular film and crystal of apatite. For the study on evaluation of physical properties and elementary technology, the surface and interface of ceramics such as apatite were investigated by means of spectroscopy, the electronic state was analyzed by the quantum chemical calculation, and the crystalline structure was analyzed using X-ray equipment. 270 refs., 102 figs., 10 tabs.

Study on electroseismic prospecting; Electroseismic tansaho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onaru, I [Kyushu University, Fukuoka (Japan); Irie, S [Mitsubishi Materials Corp., Tokyo (Japan); Tanaka, T; Mizunaga, H; Ushijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-22

This paper illustrates the results of field tests conducted as a basic investigation of electroseismic phenomenon at the site of Kyushu University. The electroseismic phenomenon is a physical phenomenon in which electromagnetic response is derived by the incident elastic wave in the underground. According to Karl E. Butler, et al., mutual motion occurs between rock matrix and pore water by the propagation of P-wave in porous media. Spatial change in the water content per unit volume occurs, which is similar to the density change with the propagation of P-wave in elastic solid. Since the pore water with mobility can bring charges generated in the electrical double layer, the change in the water content agrees with the density change. Accordingly, domains of positive and negative overcharges are generated at the top of P-wave, which can be a current source. An electric field is generated between the domains. As a result of the field tests, it was confirmed that electromagnetic phenomena can be derived by the elastic waves. 2 refs., 8 figs.

Study of white noise; Hakushoku zatsuon ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kano, R; Tada, R [Teikoku Oil Co. Ltd., Tokyo (Japan)

1996-05-01

A study was made on conditions available for white noise belonging to a finite power function with the use of a power spectrum conception. It was defined that a real variable function with a finite waveform energy was a finite energy function while that with a finite waveform power was a finite power function. A noncorrelative white noise was defined as a real variable function in which an autocorrelation function took a specific value at a certain point; however, the autocorrelation function was different between the finite energy function and the finite power function. In other words, the definition of white noise was such that `an energy spectrum was a fixed value` in the finite energy function, and that `a power spectrum was a fixed value` in the finite power function. It was pointed out, by Matsuyama (1994) with the use of the energy spectrum conception, that the white noise belonging to the finite energy function took only the form of `an arbitrary impulse function that all turned to zero except a certain point`. The same conclusion was obtained with respect to the white noise belonging to the finite power function. 1 ref., 1 tab.

Electron attachment coefficient in low E/N regions and a discussion of discharge-instability in KrF laser. ; Analysis by logarithm transformed Boltzmann equation. Tei E/N ryoiki no denshi fuchaku keisu to KrF laser reiki hoden no fuanteisei ni kansuru ichi kosatsu. ; Tai su henkan Boltzmann hoteishiki ni yoru kaiseki

Energy Technology Data Exchange (ETDEWEB)

Kawakami, H.; Urabe, J.; Yukimura, K. (Doshisha Univ., Kyoto (Japan))

1991-03-20

In a discharge excitation rare gas halide excima laser, uniform generation and stable maintenance of the excited discharge determines the laser characteristics. In this report, an approximate solution was obtained on the Boltzmann equation (frequently used for the theoretical analysis of this laser) to examine the nature of the solution. By optimizing the conversion of the variables, calculation of an electron swarm parameter in the hitherto uncertain range of the low conversion electric field was made possible, giving a generation mechanism of the uncertainty of the excited dischareg. The results are summarized as below. (1) The Boltzmann equation gives a linear solution for a logarithmic value of an electron energy in the range of low conversion electric field. (2) Time-wise responce ability between the measured voltage, current characteristics of the excitation discharge was clarified and the attachment and ionization coefficients calculated by Boltzmann equation. (3) Dependency of the attachment coefficient on the partial pressure of fluorine and kripton was examined, and the attachment coefficient was found to increase with the increase of the partial pressure for the both cases. 20 refs., 9 figs., 2 tabs.

Study of biogas storage; Biogas no chozo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Kimura, T; Umeda, H [Meiji University, Tokyo (Japan)

1997-11-25

Study was made on the storage method of a methane component in biogas mainly composed of CO2 and methane gases. Methane clathrate as molecular complex is one kind of clathrate compounds. Eight methane gas molecules are absorbed into 46 water molecules, or methane gas of 216 l is absorbed into water of 1 l, resulting in considerable compact methane storage. Although methane clathrate is usually stable only under a condition of low temperature and high pressure, its formation equilibrium shifts toward a low pressure/high temperature side by adding additives such as amine, ether and ketone. Acetone can shift formation pressure from 30 to 10atm at 1degC, and formation temperature from 1 to 10degC at 30atm. Although methane liquefaction is also an efficient storage method, it requires liquefaction temperature and pressure of -83degC and 45.6atm, respectively. The distance between methane molecules in clathrate lattice can be more shortened than that in high- pressure charged gas, suggesting higher storage efficiency. The study result showed that the handling of methane clathrate is possible around room temperature and pressure. 7 refs., 5 figs.

Proper knowledge about the growing fat; Himan ni kansuru tadashii chishiki

Energy Technology Data Exchange (ETDEWEB)

Sakamot, Yoichi

1999-07-01

Body fat is substituted for the energy adopted redundantly in the inside of the body, and the deep diabetes which relates to the increase in the fat person and this, high blood pressure, high fat blood diseases, ventilation and so-called life habit sicknesses such as an arteriosclerosis disease have been increasing. It thinks with growing fat when it wants it understood why it grows fat as to something as to that fearfulness about growing fat properly. The health making based on the individual and the weight control can't be missed to get the rich old age, which it lives through the middle age. (NEDO)

Studies on ternary silver sulfides; Fukugo gin ryukabutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Some sulfides containing silver show high ion mobility based on movability of silver, whose application is expected. Studies have been carried out centrally on synthesis of new compounds of ternary silver sulfides by elucidating the relationship among their compositions, structures and properties by means of crystal chemical studies mainly on their phase relationship. A few new compounds have been synthesized, such as the ones having the argyrodite family compound structure including transition metals. The synthesizing process takes a kind of turbulent liquid state structure at elevated temperatures because of movability of silver, but silver is fixed at low temperatures in different sites between skeleton structures made by other atoms. These studies on phase transfer, structures, and silver movability have been based on X-ray diffraction, infrared and Raman spectroscopic measurements, NMR, measurements of electric and thermal characteristics. For the studies related to compositions and structures of ternary metal sulfides which take compound crystalline structure, a structure analyzing method based on multi-dimensional hyperspatial groups was used. This paper reports the summary of the studies in seven chapters, and dwells on the remaining problems and future prospects. 158 refs., 114 figs., 65 tabs.

Studies of coal slurries property; Slurry no seijo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Kawabata, M.; Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Sakaki, T.; Shibata, M.; Hirosue, H. [Kyushu National Industrial Research Institute, Saga (Japan)

1996-10-28

It was previously found that the increase of slurry temperature provides a significant effect of slurry viscosity reduction for the coal slurry with high concentration of 50 wt%. To investigate the detailed influence of slurry temperature for the coal slurry with concentration of 50 wt%, influence of temperature on the successive change of apparent viscosity was observed at the constant shear rate. When the concentration of coal was increased from 45 wt% to 50 wt%, viscosity of the slurry was rapidly increased. When heated above 70{degree}C, the apparent viscosity decreased during heating to the given temperature, but it increased successively after reaching to the given temperature. The apparent viscosity showed higher value than that of the initial viscosity. The coal slurry with concentration of 50 wt% showed the fluidity of Newtonian fluid at the lower shear rate region, but showed the fluidity of pseudo-plastic fluid at the higher shear rate region. The slurry having high apparent viscosity by the successive change showed higher apparent viscosity with increasing the higher even by changing the shear rate. 1 ref., 4 figs.

Study of odor inside cars; Kuruma no nioi ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sato, S.; Ito, H.; Sakakibara, K.; Kaitani, K.; Hamada, C. [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Matsuo, M. [Toyota Motor Corp., Aichi (Japan)

1998-05-01

This paper describes odor in automotive cabin. Odor of new cars is rapidly disappeared during the use. This is greatly due to the adaptation of olfaction. The generation of odor is also decreased. It was found that aliphatic and aromatic hydrocarbons were rapidly disappeared. Decrements of oxygen containing and sulfur compounds were low. For amines, high boiling amines increased after three months. The odor component from crews was derived from the exhalation. Trimethylamine, methyl sulfide as well as iso-prene were detected. They could be derived from tobacco smoke, perfume and hair conditioner. Exhaust gas of diesel vehicle going ahead is one of unpleasant odors from the running atmosphere. A correlation coefficient 0.77 was obtained between the stimulation and aldehyde/ketone. A correlation equation was deduced using stimulation, discomfort degree and odor characteristics as object variables and using logarithms of trace analysis values as explanation variables. There are still a lot of unknown issues concerning combined odors. 9 refs., 9 figs., 1 tab.

Anfo and prill ammonium nitrate. Technological view of their origin and development; ANFO oyobi prill shoan ni tsuite. Tanjo to hatten no gijutsuteki kosatsu

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. [Okamoto Machine Tool Works, Ltd., Yokohama (Japan)

1997-06-30

Anfo (Ammonium Nitrate and Fuel Oil)is an explosive consisting of prill ammonium nitrate and light oil that immediately spread across the world upon its debut in the U.S. around 1956, but the details of its birth, for example the name of its inventor, are not known. Granular ammonium nitrate is in production, with its porosity enhanced to elevate oil absorption efficiency to the level for the nitrate to be proper as the material for the anfo by adjusting the water content at approximately 4% in the ammonium nitrate mother liquid before corning. Efforts are being exerted by manufacturers to improve the drying process to remove excess water efficiently from granular ammonium nitrate. In Japan, industrial production of prill ammonium nitrate for the anfo began in 1964. Since then, the problem of anfo sensitivity to detonation has been solved by adjusting the oil absorption rate of prill ammonium nitrate to be in the range of 10-12%, and the problem of ammonium nitrate solidification has been solved by the development of a solidification preventing technology that utilizes solidification preventing agents based on organic surface active agents (while inorganic anti-bonding agents are in popular use in the U.S. and Europe)

Experimental study on the effective utilization of combusted scallop cultivation waste. Hotate yoshoku haikibutsu no yuko riyo no tame no shokyaku shori joken no jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hase, Y [The Tohoku Electric Power Co. Inc., Sendai (Japan)

1993-06-15

Discussions are given on treatment methods that can utilize scallop cultivation wastes effectively. Tests to incinerate and convert the main scallop shell content, calcium carbonate, into calcium oxide (CaO) discovered optimal incinerating conditions of a temperature at 750[degree]C and a duration for 30 minutes, and 700[degree]C and one hour. CaO content in burnt shells was so high that they could be used as a raw material for quick lime. In the incineration and conversion tests on wastes from shell processing factories, the result of X-ray diffraction in chemically combined conditions of inorganics before and after the incineration revealed that the main component Ca existed as CaCO3, which may be converted into CaO when incinerated. The result also showed that the second component, Mg, existed as MgO after the incineration. From the above results, incinerating the wastes from shell processing factories at 750[degree]C would be capable of incinerating organic components completely and reducing their weights. Because the inorganic residues have high CaO content, they could be utilized effectively as a quick lime raw material. Although shells to be incinerated have low salt content because of having been boiled, salt content in scallop processing factory wastes will require discussions on possibilities of its corroding an incineration furnace. 3 figs., 7 tabs.

Experimental study of exhaust noise generated by pulsating flow downstream of pipe end; Myakudoryu ni yori yukisareru kantanbu karyu ni okeru haiki soon no jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Higashiyama, J; Iwamoto, J [Tokyo Denki University, Tokyo (Japan)

1997-10-01

A experimental study was carried out for the emissoin of the exhaust noise from an open end of the pipe generated by the pulsating flow in the pipe. The pressure histories along the pipe, the exhaust noise and visualized the flow field downstream of the pipe end were obtained. And a characteristic of frequency for the exhaust noise was examined, using Wigner distribution (WD). A relation between the pulsating flow in the pipe and the exhaust noise was important for understanding the mechanism of the exhaust noise generation. 4 refs., 8 figs., 1 tab.

Recent topics on aerodynamic noise; Kuriki soon ni kansuru saikin no wadai

Energy Technology Data Exchange (ETDEWEB)

Nishimura, M [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

1995-04-20

For measures to deal with aerodynamic noise, recent subjects were put in order and some examples of the studies were introduced in this paper. Aerodynamic noise can be classified into rotational aerodynamic noise such as jet engine fans or helicopter rotors and general aerodynamic noise such as high speed jet noise, high speed air flow inside piping, and external noise from vehicles, cars and aeroplanes. The aerodynamic noise of the air flow radiated from a wind tunnel exit was caused more or less by the pressure fluctuation of a boundary layer in a high frequency wave region. In checking the noise generated from a difference in level, projection, cavity, opening, etc., of a high speed vehicle in a wind tunnel test, the noise was louder in the case of a difference in level where the downstream side was raised. The finding was similar with projections. In the rear of a super sonic choke part, a strong flow was generated and became a violent noise source when a flow was overexpanded and a pressure was recovered with a sonic boom. However, the noise was greatly reduced by installing a porous material such as a porous metal immediately behind the choke part. An active control of noise was carried out by changing a sound field characteristic against aerodynamic self-excited noise with a speaker. 32 refs., 11 figs.

Research on harmonized molecular materials; Bunshi kyocho zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Harmonized molecular materials (HMM) were researched to create functional materials adaptable to needs such as environmental harmony and high-efficient conversion in post-industrial society and aging society. Superior mechanisms function efficiently in organisms for perception, transmission and processing of information, and transport and conversion of substances. These functions are caused by harmonization between organic molecules, or organic molecule and metal or inorganic substance. HMM is a key substance to realize these functions similar to those of organisms artificially. It is the purpose of this research to develop HMMs, reform production process by innovating separation and conversion technologies, and finally realize molecular chemical plants. This research also develops high-efficient devices to contribute to the information society, and progresses the industry of bio-functional materials such as high-sensitive bio-sensor. The functions, applications and creation technologies of three kinds of HMM such as assembly, mesophase and microporous materials were researched in fiscal 1995. 956 refs., 128 figs., 13 tabs.

Investigation research on autonomous responsive materials; Jiritsu oto zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A survey was made on autonomous responsive materials as a new material which reversibly change molecular structures and the aggregation state according to external stimuli. Autonomous responsive materials imitate environmental responsibility in the living organism system and have sensing, control and active functions for external stimuli. The materials are highly efficient and environmentally friendly. In biomimetic materials for soft actuators, drastic changes by temperature of elastic modulus of water-swollen hydrogel are used to the motion. In order to molecularly design stimulus-responsible polymer gel, studied are the relation between the micro structure and stimulus responsibility, dynamic correlation between the micro structure and the macro structure, etc. In the biomedical field, new cure and diagnosis using innovative materials are expected, and the application of autonomous responsive materials to the field is studied. For example, using hydrogel responding the temperature and the surface and controlling by temperature the interaction with components of the organism such as protein and cells, drug delivery in the organism is optimized. Also studied is the application of hydrophilic/hydrophobic changes by temperature to the chromatography. 215 refs., 47 figs., 11 tabs.

Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

2000-03-24

Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

Recent surveys and researches on pollinosis in Japan; Kafunsho ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shido, T. [The Inst. of Public Health, Tokyo (Japan)

1998-05-31

In this paper, recent investigations and researches on pollinosis are summarized as centering on the investigation entrusted by the Ministry of Health and Welfare and executed since 1992, and especially the surveys on Japanese cedar pollinosis during 1995 to 1996. The quantity of pollen surveyed in 1995 is the greatest in the survey history of nationwide flying pollen. Particularly, the quantity of cedar and hinoki pollen is 10 to 40 times as many as that in the year before. Consequently, since the sensitization and onset due to the cedar pollen increased greatly, the objects of the surveys and the researches were mainly in respect to the analysis of onset factors of pollinosis, clarification of its natural process, evaluation on the effectiveness of desensitization therapy, the clinical subjects including the confirmation of pharynx symptom and asthma symptom, and the discovery of naturally sensitizing dog. A fact that the quantity of flying pollen concerns the occurrence and degree of the clinical symptom has already been indicated by a clinical observation carried out for a long period of time. In respect to specific prophylaxis and therapy, for the first time the pollen masks and glasses sold on the market are investigated, and the necessity of the verification thereof is described. 27 refs., 7 figs., 5 tabs.

Interpretation of seismic section by acoustic modeling. Study of large amplitude events; Hadoba modeling ni yoru jishin tansa danmen no kaishaku. Kyoshinhaba event ni taisuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Tamagawa, T; Matsuoka, T; Sato, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Minegishi, M; Tsuru, T [Japan National Oil Corp., Tokyo (Japan)

1996-05-01

A large amplitude event difficult to interpret was discovered in the overlap section in offset data beyond 10km targeting at deep structures, and the event was examined. A wave field modeling was carried out by use of a simplified synclinal structure model because it had been estimated that the large amplitude event had something to do with a synclinal structure. A pseudospectral program was used for modeling the wave field on the assumption that the synclinal structure model would be an acoustic body and that the surface would contain free boundaries and multiple reflection. It was found as the result that a discontinuous large amplitude event is mapped out in the synclinal part of the overlap section when a far trace is applied beyond the structure during a CMP overlap process. This can be attributed to the concentration of energy produced by multiple reflection in the synclinal part and by the reflection waves beyond the critical angle. Accordingly, it is possible that phenomena similar to those encountered in the modeling process are emerging during actual observation. 2 refs., 8 figs.

Study on the reaction mechanism of oxygen-added enzymes for the effective utilization of unused sea weeds; Miriyo kaiso no shigenka ni kansuru sanso tenka sanso no hanno kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To effectively utilize unused sea weeds having ingestion obstructing activities for feed, the treatment by oxygen added enzyme has been investigated. Undaria pinnatifida was pasted and solidified with agar, to prepare the standard feed. Individuals of Holiotis discus hannai Ino were bred in the cistern. Extracts from ten kinds of sea weed distributed in the Sanriku Coast were added to the feed, which were compared with the standard feed to determine the ingestion obstructing activities. A testing method using cellulose painted aluminum sheet was also employed. All of the extracts from sea weeds having the ingestion obstructing activities exhibited the strong phenol reactions. The sensitivity of individuals of Holiotis discus hannai Ino depended greatly on the derived species and the chemical structures of phenolic substances. The {alpha}-hydroxymuconic acid semialdehyde (HMS), an enzyme decomposition product of catechol, provided no ingestion obstructing activity, and showed a little ingestion accelerating activity. This was considered to become ingestible through the biodegradation of phenolic substances. The HMS, a decomposition product of catechol 2,3-oxygen added enzyme derived from the petroleum decomposition bacteria, was prospective as a highly functional compound synthesizing material. 10 refs., 34 figs., 10 tabs.

Systematic analysis on mooring systems of floating structures; Futai keiryuho ni kansuru keitoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K; Suzuki, H; Ide, T [The University of Tokyo, Tokyo (Japan)

1997-12-31

Discussed herein are mooring performance requirements of the new types of marine structures now proposed, and characteristic ranges and future expansion potential of the existing mooring systems. The mooring systems studied for floating structures are catenary, single point (multi-leg and single-leg types), fixed structure with fender and tension leg mooring systems. The studied items include extraction of the elements that constitute rigidity of the spring for horizontal mooring, survey on and data collection for each element, determination of element ranges, programs for mooring analysis, assessment of mooring characteristic ranges, and potential development of the characteristic ranges. It is concluded that the existing systems with their current characteristic ranges and future possibility are insufficient for the future marine structures. It is therefore necessary to develop new mooring concepts, instead of expanding the current concepts, in order to meet the mooring performance requirements for the new marine structures. 14 refs., 9 figs., 11 tabs.

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Layered multinary lanthanum oxide [La-Mo-O]; Sojo rantan fukugo sankabutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

Studies have been carried out systematically on properties of oxides including representative transition metal, vanadium, and alkali metals. With respect to Ln2CuO4 (Ln is a rare earth element) being a simple and representative rare earth multinary oxide showing superconductivity, and its related compounds, this paper reports thermal chemistry, superconduction, and making them a superconductor by using soft chemical treatment. The paper also reports centrally on synthesis of new copper oxide superconductors under high pressure, the compositions, structures, superconductive properties of the synthetics, and the relationship between them. It describes phase equilibrium, synthesis, and structures of vanadium multinary oxides being the object of continued studies, and also reports the studies related to structure and phase transfer of NaV6O11 which shows especially interesting properties among the oxides. Studies have also been made on NMR of these compounds and copper oxide superconductors by using magnetic resonance. The paper also describes a method to analyze the structure of quasi-crystal having rotary symmetry which is not allowed in crystals, and has special long-distance order phase. 209 refs., 127 figs., 6 tabs.

Relationship between stacking process and resolution; Jugo shori to bunkaino ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsushima, J; Rokugawa, S; Kato, Y [Geological Survey of Japan, Tsukuba (Japan); Yokota, T; Miyazaki, T [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1996-10-01

This paper evaluates influences of stacking of incident angles against the reflecting surface on the resolution. Basic equations for evaluating the influences were deduced. A simple evaluation method has been provided using these equations. The present evaluation method is considered to be useful for acquisition design, processing, and interpretation of data as an indicator. According to the equations introduced in this study, there are some demerits for stacking traces whose incident angles were large. A total reflection region often appears due to the decreased resolution, and the vertical resolution decreases prior to stacking. Occasionally, it is not effective to remove traces having large incident angles from the viewpoint of resolution. In practice, the selection of most suitable trace through trial and error is not easy due to difference in individual regions. An evaluation method must be discussed, by which the optimal trace can be selected automatically during the data processing. 6 refs., 15 figs.

Study on accretion of ice on oscillating aerofoils; Shindoyokujo no chakuhyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishikawa, S; Sugihara, H [Kandenko Co. Ltd., Tokyo (Japan); Kimura, S; Sugiyama, Y [Kanagawa Institute of Technology, Kanagawa (Japan); Tsuboi, K [Ibaraki University, Ibaraki (Japan). Faculty of Engineering

1997-11-25

The effects of pitching and heaving motions of an aerofoil on accretion of ice thereon are investigated for the design of wind turbine blades. The conditions under which an aerofoil shows a heaving motion are 10m/s as wind velocity, -12degC as ambient temperature, 0.5Hz as frequency and 5mm as amplitude. Initial growth of ice is stochastic to a great extent; ice grows rapidly around the seed which is formed by chance somewhere on an laerofoil. The effects of ice appear in the flow field in the vicinity of the aerofoil front edge, as it continues to grow, providing different conditions for water droplets to collide with each other. Average ice shapes can be classified by environment, although at low repeatability. Range of ice accretion varies depending on aerofoil motion, whether it is pitching, heaving or at rest. The most important factor that determines behavior of ice accretion is conditions of the flow field near the aerofoil front edge. In a pitching or heaving motion, its speed is an important factor for growth of ice. 2 refs., 5 figs.

Study on reduction method of brake squeal; Brake naki teigen shuho ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Nakajima, T; Okada, Y [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

The reduction of brake squeal is an important technological subject in terms of making vehicles quieter. In our research, we carried out a modal analysis from the caliper to the installation bracket during generating brake squeal to identify the places that influence the squeal. Based on this, we studied proposals to reduce the squeal, and have reduced the squeal noise at about 5 kHz as reported in this paper. 1 ref., 12 figs.

Systematic analysis on mooring systems of floating structures; Futai keiryuho ni kansuru keitoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yoshida, K.; Suzuki, H.; Ide, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

Discussed herein are mooring performance requirements of the new types of marine structures now proposed, and characteristic ranges and future expansion potential of the existing mooring systems. The mooring systems studied for floating structures are catenary, single point (multi-leg and single-leg types), fixed structure with fender and tension leg mooring systems. The studied items include extraction of the elements that constitute rigidity of the spring for horizontal mooring, survey on and data collection for each element, determination of element ranges, programs for mooring analysis, assessment of mooring characteristic ranges, and potential development of the characteristic ranges. It is concluded that the existing systems with their current characteristic ranges and future possibility are insufficient for the future marine structures. It is therefore necessary to develop new mooring concepts, instead of expanding the current concepts, in order to meet the mooring performance requirements for the new marine structures. 14 refs., 9 figs., 11 tabs.

Research study on harmonized molecular materials (HMM); Bunshi kyocho zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As functional material to satisfy various needs for environmental harmonization and efficient conversion for information-oriented and aging societies, HMM were surveyed. Living bodies effectively carry out transmission/processing of information, and transport/conversion of substances, and these functions are based on harmonization between organic molecules, and between those and metal or inorganic ones. HMM is a key substance to artificially realize these bio-related functions. Its R & D aims at (1) Making a breakthrough in production process based on innovation of material separation/conversion technology, (2) Contribution to an information-oriented society by high-efficiency devices, and (3) Growth of a functional bio-material industry. HMM is classified into three categories: (1) Assembly materials such as organic ultra-thin films (LB film, self-organizing film), and organic/inorganic hybrid materials for optoelectronics, sensors and devices, (2) Mesophase materials such as functional separation membrane and photo-conductive material, and (3) Microporous materials such as synthetic catalyst using guest/host materials. 571 refs., 88 figs., 21 tabs.

Study of fuel control strategy based on an fuel behavior model for starting conditions; Nenryo kyodo model ni motozuita shidoji no nenryo hosei hosho ni tsuite no kosatsu

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Y; Uchida, M; Iwano, H; Oba, H [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

We have applied a fuel behavior model to a fuel injection system which we call SOFIS (Sophisticated and Optimized Fuel Injection System) so that we get air/fuel ratio control accuracy and good driveability. However the fuel behavior under starting conditions is still not clear. To meet low emission rules and to get better driveability under starting conditions, better air/fuel ratio control is necessary. Now we have understood the ignition timing, injection timing, and injection pulse width required in such conditions. In former days, we analyzed the state of the air/fuel mixture under cold conditions and made a new fuel behavior model which considered fuel loss such as hydrocarbons and dissolution into oil and so on. Al this time, we have applied this idea to starting. We confirm this new model offers improved air/fuel ratio control. 6 refs., 9 figs., 3 tabs.

Basic study on intelligent materialization of glass; Glass no intelligent ko zairyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

This is the report No. 98 issued by the Inorganic Material Research Institute. An intelligent material is a substance and/or material which responds intelligently to environmental conditions and exhibits functions. One of the features of amorphous materials including amorphous glass is a large freedom in chemical composition. These materials maintain order in short distance, but have as a whole the turbulent and specific atom orientation. Therefore, high tolerability in selecting the composition, and diverse synthesizing methods are available. A wide range of utilization may be conceived, such as introduction of the state of electrons having different valences in a structure, and the diverse chemical combinations. Patterns of existence of polyhedrons having different orientations, and how they are connected correlate closely with an external environment. Intelligent materials have high freedom against change in the external environment and are suitable to exhibit intelligent functions. Setting heat and light as the external conditions, attempts have been made on search and creation of intelligent materials based on state change induced by interactions between the two factors. Fundamental studies have been made on synthesis of different environment responding glasses and films, and on factors and phenomena for exhibition of the intelligence. 62 refs., 91 figs., 8 tabs.

Study on search of unknown materials. 1; Michi busshitsu no tansaku ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-28

This is No.92 report of National Institute for Research in Inorganic Materials, concerning search of unknown materials. Purposes of this study are to construct new chemical bond and reaction theory, to systematize the existing compounds, and to search and create the unknown materials, systematically. Structure prediction of electronic state was investigated by means of molecular dynamic method, to determine the electronic state and structure of multi-systems. For the magnetic semiconductors, interactions were investigated between the magnetic spin and electron or hole which is a carrier. The in-solid bond theory aims at clarifying the bond state of materials in which transition metal compounds and inter-electronic interactions are significant. Prediction of the electronic structure of unknown materials can suggest the design of new materials. In the fields of synthesis, design and synthesis of new inorganic ion exchanger and ionic conductor are investigated using Bi oxides and its related materials. There are a lot of compounds having various crystal forms for rare earth element oxides and transition metal oxides. To establish the system of material design, thermodynamics, phase equilibrium diagram, crystal structure, and physical properties of new materials were discussed. 168 refs., 127 figs., 44 tabs.

Development of new supervisory system with ITV. ITV ni yoru kanshi system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimonaga, S; Matsunaga, R; Ono, H [The Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1994-02-28

This paper describes an automatic trespassing supervisory system with ITV and picture processing (PP). The paper details an integrated control system and automatic supervision. The system functions to automatically detect a trespassing by means of PP, transfers items of information collected by sensors to a remote control center, and records relevant data. The operation principle consists of measurement of change in two or more images of moving bodies with binary value at a certain interval, determination on acceptability of the moving bodies represented by human characteristics, and identification of a trespasser. The system consists of an automatic supervisory device using PP and an automatic patrolling and searching device by means of sensor measurements. The supervisory device has images outputted from ITV and VTR processed by PP, host computer, and HD, and linked to an indication mechanism. According to the result of a site test at wireless transmission station of Kyushu Electric Power Company, the difference between measurement values collected by the searching device and those by the supervisory device was [plus minus]3% or less (other than EG output current), which is a useful value for verification. Although the basic technique has been established, practical use of the system still has some problems including performance improvement in picture processing. 37 refs., 38 figs., 18 tabs.

Proceedings of RITE international workshop on valuation; Total eko balance ni kansuru kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The RITE International Workshop on Valuation was held in Tokyo and Osaka in February 1996, and eight papers on total ecobalance were reported. In The Field of Impact Assessment, described were constitution and methodology about impact assessment in a wide sense. In LCA Yesterday, Today and Tomorrow, discussed were the historical development and future outlook of LCA. In Standardization of Product Life Cycle Assessment, a survey of the present situation of LCA international standardization was made. In the Relationship between Product Life Cycle Assessment Methodology, considered was the relationship between the goal definition of the product life cycle assessment and the methodological choices. In Valuation in LCA, the present study of LCA was reviewed. Besides, reviews of the LCA study in Japan were made public.

Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

Study on a non-powered heat transporting system; Mudoryoku netsu hanso system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kamiya, Y [Kanto Gakuin University, Yokohama (Japan)

1997-11-25

This paper proposes a non-powered heat transportation (HT) system. The system is composed of an evaporator, condenser, receiver, switching chamber (SC) and 3 check valves which are connected with each other by vapor and liquid tubes. Condensed liquid supercooled in the condenser exists in the receiver forming a saturated condition at a concerned temperature, and condensed liquid is lifted up from the condenser to the receiver by pressure difference between the evaporator and receiver. Generally evaporation pressure is higher by pressure difference between liquid levels in the condenser and receiver. The lifted up amount of condensed liquid increases with evaporation pressure, resulting in an increase in heating surface area of the condenser and amount of condensed liquid. A proper evaporator pressure is thus retained by reduction of evaporation pressure. SC is connected with the receiver and evaporator, and switches high- and low-pressure valves by motion of an inner float to transport heat from the evaporator to condenser. Reverse HT is possible as normal latent HT by installing a bypass. Some problems are also described. 2 refs., 8 figs.

Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

Improvement of performance of the HARBEMAN house; Habiman hausu no seino kaizen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Saito, T. [Tohoku Univ., Sendai (Japan). Dept. of Aeronautics and Space Eng.; Fujino, T. [Mitsubishi Heavy Industires Ltd., Tokyo (Japan)

1998-12-05

A natural energy autonomous house (HARBEMAN house) was built in 1996 in Sendai. This house combinedly utilizes solar thermal, photovoltaic, sky radiation cooling, rainwater energies and so on. In order to utilize a lot kind of natural energies more efficiently, we will improve thermal performance of the solar collector, the sky radiator, and so on. The effect of thermal insulation, tank size, and window glazing on thermal performance will also be examined. This article reports on the improved performance of the HARBEMAN house. (author)

Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1997-07-10

The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

Report on 'manufacturing technology supported by advanced and integrated information system through international cooperation'. Domestic surveys; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kokunai chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The committee of manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC) has been established as the organization to promote necessary surveys, deliberate the research and development guidelines and themes, and thereby support the joint R and D projects with Asian countries to improve information systems for their manufacturing industries by MATIC. The R and D skeletons are set in FY 1994 for the works in and after FY 1995. The relationships between affiliates of Japanese enterprises and local enterprises, actual conditions of the manufacturing industries and so on are surveyed, in order to extract problems related to the information systems for the promising manufacturing industries in the Asian countries. Each industry has its own characteristics with respect to, e.g., numbers f parts and process steps, product life cycle, extent of automation, skill of workers, and spread of the related industries. Therefore, 3 industrial areas are picked up as those considered to be adequate for the case studies, and surveyed for the system functions, performance, elementary techniques and so on which are required to establish the information systems for their production systems. (NEDO)

Report on a survey in fiscal 1999. Survey on the actual state of utilizing unified evaluation models for global warming; 1999 nendo chikyu ondanka ni kansuru togo hyoka model no katsuyo jittai ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present survey is intended to compare and analyze major unified global warming evaluation models available inside and outside the country, and analyze the directionality on supports for the future model developments that will be performed by the Ministry of International Trade and Industry. The report describes in Section 1 how the summaries of the global warming evaluation models may be put into order. A unified evaluation model may be positioned basically as a platform to unify the processes of recognizing scientific problems and the processes of determining the policies. Section 2 describes how the summaries of the major global warming evaluation models may be put into order. The models include the followings: DNE21 (Dynamic New Earth 21), GRAPE model, AIM model, MESSAGE (IIASA) model, IMAGE2 (RIVM), and GREEN (Gene Ral Equilibrium Environment)(OECD). Section 3 summarizes the purposes, general situation of development, scope of the objects, and technological features as the features of each model. Section 4 describes the analysis of the actual state of utilizing unified evaluation models for global warming. The results of the analysis were put into order in a map form to make clear the positioning of the major models that have been put into order. (NEDO)

Consideration of the reservoir by the temperature history at the Hijiori HDR (hot dry rock) wells; Hijiori koon gantai no kokukosei ni okeru ondo rireki wo mochiita choryuso no kosatsu

Energy Technology Data Exchange (ETDEWEB)

Takahashi, W; Shinohara, N; Osato, K; Takasugi, S [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

1997-10-22

Hot dry rock (HDR) power generation has been promoted by NEDO since 1984 at Hijiori, Okura village, Mogami-gun, Yamagata Prefecture. Hydraulic fracture tests and circulation tests have been conducted using four wells named as SKG-2, HDR-1, HDR-2 and HDR-3. Based on these test results, flow models of Hijiori shallow and deep reservoirs have been proposed. Conventional circulation tests have been analyzed only using temperature profile data. In this paper, circulation tests are analyzed by numerical simulation, to discuss individual characteristics of the shallow and deep reservoirs. Injection flow, production flow and circulation days were inputted as past circulation test data, to discuss the characteristics of geological layers, especially the permeability data, by which the features of temperature profiles in each well can be explained. As a result, it was found that the extension of permeable zone affecting the temperature in the SKG-2 well equivalent to the shallow reservoir was larger than that in the HDR-1 well. It was also found that there was a large difference in the permeability between the HDR-2a and HDR-3 wells. 5 refs., 8 figs., 2 tabs.

Survey on commercial use of fuel cells; Nenryo denchi ni kansuru jitsuyoka no tame no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The basic survey was carried out for the future approach to R & D of fuel cells. Phosphoric acid fuel cell (PAFC) is in the stage of demonstration research and field test supported by subsidy after the end of Sunshine project. Its reliability and durability problems are being solved, and its cost reduction is only one problem for practical use. Distributed systems or on-site systems will be used utilizing its excellent environmental characteristics. Molten carbonate fuel cell (MCFC), solid oxide one (SOFC) and polymer electrolyte one (PEFC) under development were thus surveyed. The following are surveyed: (1) Contribution to a human society such as improvement of energy demand/supply structure and environmental protection, (2) Technological items such as outlook for R & D, validity of developmental issues, comparison between various R & D and significance in industrial promotion, (3) Economic items such as profitability and feasible period, and (4) Social items such as sociability, compatibility to needs, possibility of locations, international meaning, market scale and promotion scenario. 90 refs., 67 figs., 96 tabs.

Investigation into the emission of greenhouse effect gases; Onshitsu koka gas no haishutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper grasped the situation of greenhouse effect gas emissions of advanced countries based on the reports from them. The advanced countries which concluded the U.N. Framework Convention on Climate Change (OECD member countries, the former U.S.S.R., and East European countries) are to be reported to the office concerned with work for the framework the situation of their greenhouse effect gas emissions according to the obligation of the framework. In and after April 1997, they made the second report. The paper summarized changes in emission amount, the future trend, and the policies/measures mainly taken of nine countries which have already presented the second report (the U.S., the U.K., Germany, Holland, Italy, Norway, Sweden, Finland, and New Zealand) and one country (Russia) which has made only the first report. Moreover, the literature was collected and summed up concerning the mechanism and coefficients of the emission of nitrous oxide and methane. The collected literature was classified into all fields/plural number of fields, energy relation, industrial process relation, relation with the use of organic solvent and other products, agricultural relation, relation with changes in land use and forests, and waste relation. 4 figs., 228 tabs.

Survey and research on applications of parallel compiler; Heiretsu compiler tekiyorei ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-31

An urgent proposition is made that an advanced computing software program development and maintenance system be set up, and activities are conducted in search of strategies and guidelines for the establishment of such a system. Out of recognition that it is important to develop software programs such as operation systems for supercomputers, a survey is conducted of software technology development strategies especially involving application software programs. It is proposed that efforts be positively exerted to develop strategic software developing programs for advanced computing for concentratedly enhancing the development now under way of strategic software programs. In concrete terms, named as strategic software programs to be developed are a next-generation semiconductor TCAD (technology computer-aided design) system, protein structure/function analysis system, fatigue simulation system, next-generation fluid analysis system, chemical reaction simulator, grid computing, and a nanodevice surface analysis system. (NEDO)

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

Catalytic activity of pyrite for coal liquefaction reaction; Tennen pyrite no shokubai seino ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Hirano, K.; Kozu, M.; Okada, T.; Kobayashi, M. [Nippon Coal Oil Co. Ltd., Tokyo (Japan)

1996-10-28

Since natural pyrite is easy to obtain and cheap as coal liquefaction catalyst, it is to be used for the 150 t/d scale NEDOL process bituminous coal liquefaction pilot plant. NEDO and NCOL have investigated the improvement of catalytic activity of pulverized natural pyrite for enhancing performance and economy of the NEDOL process. In this study, coal liquefaction tests were conducted using natural pyrite catalyst pulverized by dry-type bowl mill under nitrogen atmosphere. Mechanism of catalytic reaction of the natural pyrite was discussed from relations between properties of the catalyst and liquefaction product. The natural pyrite provided an activity to transfer gaseous hydrogen into the liquefaction product. It was considered that pulverized pyrite promotes the hydrogenation reaction of asphaltene because pulverization increases its contact rate with reactant and the amount of active points on its surface. It was inferred that catalytic activity of pyrite is affected greatly by the chemical state of Fe and S on its surface. 3 refs., 4 figs., 1 tab.

Experimental study on the simple water hammer pump; Kan`igata water hammer pump ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Muto, M; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1997-11-25

Outlined herein are experimental results with a water hammer pump. It is a unique pump in that it depends only on potential energy of water to pump-up water. Water flows downwards from a reservoir at a high position into the pump , and is released from the exhaust valve. When velocity of water flowing in the pipe reaches a certain level, hydraulic force exceeds gravity of the exhaust valve to rapidly closes it, which is accompanied by rapid increase in pressure in the pump. High-pressure water flows into the air chamber, after pushing up the lifting valve, to compress air in the chamber. The lifting valve is closed, when pressure in the air chamber exceeds that in the pump, to pump up water in the chamber through the lifting pipe. Closure of the lifting valve produces a negative pressure within the pump, which, together with gravity of the exhaust valve, opens the valve again. The pump lifts water at 1.64l/min under the conditions of head: 3m and lift: 6m at an efficiency of 48.1%. 1 ref., 4 fig., 2 tab.

Temperature dependency of electrical resistivity of soils; Tsuchi no hiteiko no ondo izonsei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Park, S; Matsui, T [Osaka University, Osaka (Japan). Faculty of Engineering; Park, M; Fujiwara, H [Osaka University, Osaka (Japan)

1997-10-22

Kinds of ground materials, porosity, electrical resistivity of pores, degree of saturation, and content of clays are the factors affecting the electrical resistivity of soils. In addition to these factors, the electrical resistivity of soils around hot spring water and geothermal areas depends on the temperature due to fluctuation of cation mobility in the pore water with the temperature. In this paper, the temperature dependency of electrical resistivity of groundwater and soils is investigated by recognizing that of groundwater as that of pore water. As a result, it was found that the electrical resistivity of groundwater becomes lower as increasing the amount of dissolved cation, and that the temperature dependency of electrical resistivity is not significant because of the small mobility of cation. The electrical resistivity of soils was significantly affected by that of pore water, in which the mobility of cation was changed with temperature changes. Accordingly, the temperature dependency of electrical resistivity of soils has a similar tendency as that of groundwater. 5 refs., 9 figs., 2 tabs.

Consideration of some difficulties in migration velocity analysis; Migration velocity analysis no shomondai ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Akama, K [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1997-10-22

Concerning migration velocity analysis in the seismic exploration method, two typical techniques, out of velocity analysis techniques using residual moveout in the CIP gather, are verified. Deregowski`s method uses pre-stacking deep-level migration records for velocity analysis to obtain velocities free of spatial inconsistency and not dependent on the velocity structure. This method is very like the conventional DMO velocity analysis method and is easy to understand intuitively. In this method, however, error is apt to be aggravated in the process of obtaining the depth-sector velocity from the time-RMS velocity. Al-Yahya`s method formulates the moveout residual in the CIP gather. This assumes horizontal stratification and a small residual velocity, however, and fails to guarantee convergence in the case of a steep structure or a grave model error. In the updating of the velocity model, in addition, it has to maintain required accuracy and, at the same time, incorporate smoothing to ensure not to deteriorate high convergence. 2 refs., 5 figs.

Survey of energy load leveling system in Europe; Energy fuka heijunka taisaku ni kansuru Europe chosa

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Y. [Setsunan University, Osaka (Japan). Faculty of Engineering

1998-05-05

This paper describes the survey of energy load leveling systems in Europe. In Denmark, especially regional heating is remarkably diffused, and they have 350 plants. With extending the service areas, the energy load leveling has been promoted. For the cogeneration plants of SK Power, the largest electric power company, they have hot water heat storage tanks for regional heat supply with a total capacity 2,200 MWh. The regional heating system in Goeteborg City of Sweden supplies 80% of the total heat demand of the city. Unused energy sources derived from petroleum refining, sewage treatment, and garbage burning are utilized. In Uppsala, they have seasonal heat storage systems using solar heat. The Vienna Regional Heat Supply Corporation supplies heat equivalent to 5,000 GWh a year. Cogeneration plants and garbage burning plants are used as heat sources, and 25% of the total heating in the city is supplied. In Austria, they have an electric power demand with a peak in winter, and they have a pumped-storage power station in Kaprun for the annual load leveling using dump power in summer. This paper also introduces a compressed air storage gas turbine plant at Huntorf of Germany, and a large-scale underground natural gas storage of Gaz de France. 6 figs.

Test and evaluation on safety relating to biotechnology; Biotechnology ni kansuru anzensei no shiken to hyoka

Energy Technology Data Exchange (ETDEWEB)

Okada, M. [Bio-Oriented Technology Research Advancement Inst., Saitama (Japan)

1996-09-05

This paper describes the current status and how works are being carried out on safety tests and evaluation of gene recombinants in plants and microorganisms. In the field of plants, Flavr Savr tomato which has been improved in fully ripe fruit distribution and keeping quality was commercialized as the world`s first recombinant food in May 1994 by Calgene, Inc. of America. Other vegetables, such as soybean, corn, potato, and pumpkin have been completed of all items of safety evaluation, and are approaching the commercialization phase. The safety evaluation system for living organisms created by using recombinant DNA technologies has been established internationally with regard to its general framework and contents based on accumulated knowledeges and experiences as a result of utilization of over twenty years. Industrial utilization guidelines for recombinants in Japan have been established in correspondence with the OECD recommendation in 1986. Experiments to verify recombinants to be safe in environment, and cultivation of the recombinants for utilization are performed based on the experimental guidelines and utilization guidelines. 15 refs., 1 fig., 5 tabs.

Research for a database of alternative energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper collects and arranges data on the unused energy in terms of examples of the introduction in Japan and other countries, policies, laws and rules, subsidy systems, etc. In the overview of the system, described was typical heat supply systems utilizing unused energy. As to concrete examples of the introduction in Japan, the examples were arranged by unused energy source, by temperature level, and by region, and a detailed data book of the typical introduction examples was made. As to examples overseas, data were arranged on the introduction mainly in Europe and the U.S. With relation to policies, laws and rules, and subsidy systems in Japan and overseas, investigated were policies, laws and rules, and subsidy systems concerning unused energy mostly in Japan, Europe and the U.S. As to the production quantity, the actual amount of introduction, and the predicted amount of introduction, survey on the effect and arrangement of the data were conducted in terms of typical two heat supply facilities utilizing unused energy. The paper adds information pertaining to the cost, main related companies and groups, the distribution cost, etc.

Emergency housing after natural disaster; Shizen saigaigo no oukyu kyoju kankyo seibi sisutemu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, Masami [Kyoto University, Kyoto (Japan). Graduate School of Engineering

1998-12-16

In Japan, there were some serious disasters in recent years. In 1991, Unzen-Fugendake erupted and more than 1,000 people were forced to take refuge from their houses. In 1993, Hokkaido-Nanseioki earthquake attacked the south-east area of Hokkaido and more than 3,557 houses were destroyed. In Japan, the government supplies the temporary housing to those who lost house from the natural disasters. The purpose of supplying temporary houses mentioned in the disaster relief law (established in 1947) prescribes the purpose of temporary housing that to rescue the poor who can not afford getting a shelter with their own funds. But actual condition of temporary housing is completely different. Government supplies temporary housing to all those who request temporary housing. The term of using temporary house tend to become longer. The regulation about temporary housing has not been yet up to dated. Many problems concerning about temporary housing originate in outdated regulation. The temporary housing have to be ranked in the part of restoration process from natural disaster. (author)

Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

CFD prediction of heat island formation on growing Asian cities. Effect of urbanization in Shanghai; Kyodaikasuru Asia no toshi ni okeru heat island keisei ni kansuru CFD yosoku. Shanghai no toshika ga oyobosu eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ojima, T.; Murakami, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Mitsumoto, K. [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-10-01

Study is conducted of the effect of change in land use and increase in artificial exhaust heat on heat island formation in Shanghai. Concerning the land use distribution in Shanghai, a point sampling survey was conducted in the 1930s using topographic charts, when the area was broken down into building-occupied region, paddy field, bare ground, and waters. In the 1990s, thanks to data from satellites, high-density and low-density urban regions have added. Calculation for Shanghai is performed, based on the rate of increase in Tokyo`s population and data predicted for Shanghai`s population, on the assumption that Shanghai`s population in the 2050s will grow 2.3 times larger than it is in the 1990s. The prediction thus produced indicates that the urban area in Shanghai in the 2050s will be as large as that of the present-day Tokyo that covers a 50km zone. Heat island formation prediction for Shanghai is worked out using computational fluid dynamics (CFD)-aided simulation. According to the prediction, while the maximum temperature in the 1930s was 29.6degC or 4degC higher than in the suburbs, it is 33.2degC or 7.6deg higher in the 1990s, and will be 34.4degC or 8.6degC higher in the 2050s. 16 refs., 11 figs., 1 tab.

Methods for constructing time synchronous networks. Part 1. Consideration and experiment of time synchronizing functions and devices; Zenkei jikoku dokimo no kosei shuho. 1. Jikoku doki hoshiki no kino kento to jikkenteki kensho

Energy Technology Data Exchange (ETDEWEB)

Serizawa, Y.; Kitamura, K.; Myojin, M.; Shimizu, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Nenohi, H.; Morimitsu, M.; Masui, O.; Matsushima, T. [NEC Corp., Tokyo (Japan)

1996-03-01

For the purpose of the back-up protection of regional power line system and the protection and control of accident influence, construction methods of time synchronizing network have been investigated. This paper proposes a method suitable for business power communication. For the synchronization between stations, transmission delay and its fluctuation have to be measured accurately by transmitting time signals between stations. Based on the observed delay values, the function of time correction (phase synchronizing control) of synchronized station is required. A mutual type synchronizing method was proposed, to which a sampling synchronization method of carrier relay system for transmission line protection was applied. In this method, transmission of time signals and measurement of delays are mutually conducted between stations, and phases of independent transmitters of the both stations are controlled so as to be equivalent. This method is characterized by the suppression of delays with fluctuation in the same direction of two-way transmission. For the transmission of time signals, two types of synchronizing devices were employed, i.e., synchronous and asynchronous manners. In the former, frequency synchronous network of SDH (synchronous digital hierarchy) was synchronized. In the latter, a carrier relay device was utilized independent of frequency synchronous network. It was expected that a synchronous network with an order of {mu}s can be constructed. 11 refs., 21 figs., 3 tabs.

Experimental study of gas combustion fluidized bed and radiation contribution to heat transfer inside the bed. Gas nensho ryudoso to sono sonai netsudentatsu ni okeru fukusha no kiyo ni tsuite no jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yamada, Y; Takahashi, S [Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan); Maki, H [Science Univ. of Tokyo, Noda, Chiba (Japan). Faculty of Science and Technology

1992-11-25

Fluidized bed as a coal combustion boiler has a practical application, but, there is not an example of which gas like helium as a cooling medium flow in a thin tube with diameter of 6 mm like a stirling engine and necessary data for selecting the medium of fluidized bed and estimating the heat transfer coefficient. Specially, it is difficult to correctly estimate the radiation effect concerned with the heat transfer coefficient in case of interposing the heat transfer tube at 800 [degree]C in the high-temperature fluidized bed at more than 900 [degree]C. Therefore, for investigating the thermal characteristics when the temperature of pipe itself is at high temperature, in the gas combustion fluidized bed in which alumina particle as fluidized medium is filled, the cooling tubes by using carbonic acid gas as a cooling medium was interposed, heat transfer coefficient was measured, radiation effect was clarified by experiment, and characteristics of the gas combustion and of the exhaust gas of fluidized bed when gas is used for a fuel was investigated. 13 refs., 12 figs., 1 tab.

Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

Investigation on structuring the human body function database; Shintai kino database no kochiku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Based on the concept of human life engineering database, a study was made to know how to technically make such a database fittable to the old people in the age-advancing society. It was then proposed that the old people`s human life engineering database should be prepared to serve for the development and design of life technology to be applied into the age-advancing society. An executive method of structuring the database was established through the `bathing` and `going out` selected as an action to be casestudied in the daily life of old people. As a result of the study, the proposal was made that the old people`s human body function database should be prepared as a R and D base for the life technology in the aged society. Based on the above proposal, a master plan was mapped out to structure this database with the concrete method studied for putting it into action. At the first investigation stage of the above study, documentation was made through utilizing the existing documentary database. Enterprises were also interviewed for the investigation. Pertaining to the function of old people, about 500 documents were extracted with many vague points not clarified yet. The investigation will restart in the next fiscal year. 4 refs., 38 figs., 30 tabs.

Numerical simulation on streaming potentials in a wellbore; Koseinai no ryudo den`i ni kansuru suchi simulation

Energy Technology Data Exchange (ETDEWEB)

Ikeda, N [Kyushu University, Fukuoka (Japan)

1996-05-01

This paper reports numerical computation of streaming potentials which are generated by transient pressure waves propagating the vicinity of wellbore wall immediately after a mud cake formed on the wellbore wall has been removed. One existing analysis solution on heat conduction was utilized upon changing the parameters in order to derive fluid pressure inside the ground bed. Calculations were carried out by using the existing three-dimensional finite difference method (partly re-written) based on the relationship constituted between the fluid pressure and the streaming potential. This paper presents results of calculating the streaming potentials in wellbores on models having wellbores filled with mud water in a cubic ground bed existing with ground bed water at saturation of 100%. The calculations have been conducted on the following cases: a case where permeability of the ground bed is small with the fluid under two conditions of low electric resistivity and high electric resistivity, a case where the permeability is large with the fluid under the above conditions, and a case where a small area of bore wall is covered with a rubber pad having high electric resistivity under a low electric resistivity condition. 8 refs., 5 figs.

Study on fuel particle motion of a diesel spray; Diesel funmu ryushi no kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, N. [Isuzu Motors Ltd., Tokyo (Japan); Tsujimura, K.

1998-08-25

This study was performed to clarify the mechanism of mixture formation at peripheral area of diesel spray with PIV technique. Two dimensional cross-sectional photographs of diesel spray were taken with double pulse laser sheet. Local fuel spray particles were analyzed with an auto-correlation method and velocity vector and vorticity of the fuel spray particle were obtained. The vortex number increased and vorticity scale became smaller and its value grew higher with both smaller injection nozzle diameter and higher fuel injection velocity. With this injection condition, the mixing of fuel spray with ambient gas seems to be improved and the turbulence is expected to increase in the regions of higher vortex number, higher vorticity and smaller vorticity scale. Based on above results, the branch-like structure of diesel fuel spray was considered to be caused by vortices which formed in the shear layer between the spray and the ambient gas. 14 refs., 18 figs., 1 tab.

Indoor environment and allergy except housedust mite; Jukankyo to allergy ni kansuru dani igai no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakao, F.; Nishima, S.

1998-05-31

Pathopoiesis factors of allergic diseases include immune antibody productivity sthenia reacting with antigens such as mite or the like in allergy reaction which is regarded as based on genetic fact (atopic diathesis), and environmental factors as external factors. The environmental factors are further classified into specific factors (antigens) and nonspecific factors. The former factors include the indoor factors such as mite, mould, animals bred indoor, etc., and outdoor factors such as pollen and so on. The latter factors include indoor factors such as passive smoking, carbon monoxide, nitrogen oxides, formaldehyde, etc., and outdoor factors such as sulfur oxides, nitrogen oxides, airborne particles and so on. In this paper, the environmental factors in relation to allergic diseases expect mite are introduced. Besides mould, cockroach/insect, fur dust and dandruff of animals, adjustment of room temperature/humidity, smoking, indoor and outdoor air pollution are mentioned as the environmental factors expect mite, and the cause-effect relations thereof are explained. 24 refs., 3 figs., 7 tabs.

Study on the thermal stability of nitrobenzene derivatives; Chikan nitorobenzen rui no netsu anteisei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, Tatsuya; Akutsu, Yoshiaki; Arai, Mitsuru; Tamura, Masamitsu [The University of Tokyo, Tokyo (Japan). Department of Chemical System Engineering School of Engineering

1999-10-31

In order to clarify the thermal decomposition behavior of nitrobenzene derivatives, the influences of interaction between nitro group and other substituents on thermal decomposition of nitrobenzene derivatives have been studied using sealed cell DSC and PM3 MO calculations. As a result, the mixtures of nitrobenzene and mono substituted benzenes having substituents containing hydrogen such as {sup -}CH{sub 3}, {sup -}COOH, {sup -}NH{sub 2}, and {sup -}OH showed 30-100 degree C lower T{sub DSC} value than nitrobenzene. Mono-substituted nitrobenzene having substituents containing hydrogen also showed lower T{sub DSC} value. On the other hand, PM3 MO calculations of hydrogen-bonded complexes of nitrobenzene and mono substituted benzene show that the hydrogen bonding of a nitro group and hydrogen of substituents may make the N-O bond length longer to induce the thermal decomposition. From These results, it can be said that the thermal decomposition of nitrobenzene derivatives would be unstabilized by the hydrogen bonding of a nitro group and a substituent containing hydrogen. (author)

Feasibility study for seismic monitoring of gas injection; Atsunyu gasu monitaringu no kanosei hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishida, A.; Ogawa, T.; Yokota, T.; Shimada, N.; Onozuka, S.; Kono, F.; Miyagi, T. [Japan National Oil Corp., Tokyo (Japan)

1998-10-30

In this study, seismic monitoring of injected gas in a carbonate reservoir was investigated using multidisciplinary approach which consisted of geological/reservoir modeling, reservoir flow simulation, rock physics and seismic modeling. A case study was conducted over Lower Cretaceous carbonate reservoir offshore Abu Dhabi. The gas saturation and reservoir pressure data were obtained from the reservoir flow simulation. The velocity data of dry rock samples under the various conditions were also obtained from rock physics study. These outputs were converted to the velocity model using Gassmann's equation. The calculated velocity from Gassmann's equation is well correlated with velocity from laboratory measurements. Therefore we con confirm that the Gassmann's equation is applicable to estimate the velocity of the gas saturated reservoir rock. Based on the velocity model, synthetic seismic sections before and after gas injection were constructed in order to verify the influence of gas flood. As the results, amplitude difference between the two synthetic seismograms was observed at top and bottom reflectors of the reservoir zone. This amplitude variation is caused by both gas saturation change and pressure change. Although further investigation is needed to detect the cause of the variation, this study indicates the possibility of seismic reservoir monitoring. (author)

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-10

Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

Study on the product estimation of small wind turbines; Kogata fusha no hatsudenryo yosoku ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsuzawa, K.; Kimura, Y.; Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan); Nagai, H. [Nihon Univ., Chiba (Japan). Coll. of Industrial Technology

1998-09-01

In order to clarify problems involved in application of Weibull probability distribution used for estimation of power production by a large wind turbine to a small wind turbine, and solutions thereof, the estimated results are compared with the observed ones. The conventional estimation method, when applied to a small wind turbine, tends to overestimate production of power, because of overestimated production in a high wind velocity range which occurs less frequently. Estimation of power produced by a wind turbine is based on working wind velocity range, determined from the furling mechanism for the power generation characteristics of the wind turbine concerned. In the case of a small wind turbine, on the other hand, better estimates are obtained from the working wind velocity range in which Weibull wind velocity distribution is used to determine probability of occurrence. For wind turbines working at low to medium wind velocities, such as Savonius wind turbine, the estimates are in fairly good agreement with the observed results, by which is meant that the conventional estimation method aided by Weibull distribution can be directly applicable to small wind turbines. 4 refs., 3 figs., 3 tabs.

Study on the structural characteristics of extradosed concrete bridges; Ekusutoradozudo kyo no kozo tokusei ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Oka, Y. [Japan Highway Public Corp., Tokyo (Japan); Kasuga, A. [Sumitomo Construction Co. Ltd., Tokyo (Japan); Yamazaki, J. [Nihon Univ., Tokyo (Japan). Coll. of Science and Engineering

1997-03-31

Parameters are analyzed to provide data for deciding, in the planning and designing stages, whether a cable stayed bridge or an extradosed bridge should be adopted. Comparative investigation of the vibration properties of both types of bridges is also referred to. The result of the study on the structural properties of the cable stayed road bridge and the extradosed road bridge is introduced. Based on the concept of the extradosed bridge, designers are now able to select without restraint the after load sharing rate of the diagonal members. Parameter analysis of a diagonal member reinforced 3-span continuous beam is performed. By introducing indices showing the load sharing rate of the diagonal member, the cable stayed bridge can be distinguished logically from the extradosed bridge in designing. It is found important that the height of the main tower is set to approximately 10% the length of the center span for the construction of the extradosed bridge. The vibration properties of the cable stayed bridge and the extradosed bridge of the same scale are compared. 7 refs., 18 figs., 6 tabs.

Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-11-01

On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-10

This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-11-01

On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on chemical use); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-04-15

The whole amount of hydrogen consumption for chemical industries all over the world is estimated to be 249.7 billion Nm{sup 3} in 1974, while 367.2 billion Nm{sup 3} in 1980 roughly under a bold assumption, based on 3 current big consumption fields of ammonia production, methanol production and petroleum refining, and some promising fields in the future such as reduced iron and synthetic protein. Consumption ratios for every field are probably 54.9% in ammonia production, 30% in petroleum refining, 9.5% in methanol production and 5.6% in others in 1974, and nearly similar in 1980. However, although there are various troubles, if a large amount of methanol is used as fuel in the future, and its production plan is promoted to satisfy the demand of methanol fuel, hydrogen consumption for methanol production will increase drastically. In the future, if the production process of hydrogen as secondary fuel is established, such hydrogen also will be used for various chemical industries naturally. Research was thus made on use of oxygen as byproduct inevitably. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-10

This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

International Workshop on Carbon Cycling and Coral Reef Metabolism; Sangosho no tanso junkan ni kansuru kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-16

The paper described the International Workshop on Carbon Cycling and Coral Reef Metabolism which was held at Miyako-jima, Okinawa Pref. on October 17-24, 1995. In the workshop, researchers got together which are involved in marine chemistry, marine biology, coral ecology, and environmental science, and discussed the carbon cycling and metabolism of coral reef. Discussions were made on what the coral reef ecosystem is, and what the definition of a sink or a source for CO2 is. Also discussed were scales of how much time and space should be considered to make these issues clear. Further, it was proposed that it was necessary to investigate carbon balance of both the whole system and the components of the system and to keep track of mass transfer among neighboring components of the system. Seventeen presentations were given. The workshop obtained a definite consensus on carbon balance of the coral reef system. 123 refs., 39 figs., 9 tabs.

Study on abrasion resisting material for apron of dam; Dam apron bu no taimamo sozai ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Inaba, H.; Hiraki, M.; Miyamoto, T. [Hokuriku Electric Power Co. Inc., Toyama (Japan)

1995-01-25

A `laminated rubber tile` and a `shock absorbing holed-in anchor` were devised in connection with the apron of a dam for a hydroelectric power plant. As the result of a survey on the hydroelectric power plants, ten plus places were observed where a general kind of concrete was severely worn in the company territory; but, there were substantial number of rubber materials that had still been sound for over ten years after the installation. In spite of the soundness of the rubber tiles, however, it was observed that their anchor supports had been cut and separated. An abrasion comparison test of concrete and rubber materials revealed that the rubber materials were considerably superior in abrasion resistance. Various rubber tiles were tested for abrasion resistance, tear strength, tensile strength, impact strength, etc.; and methods for fixing rubber tiles were also tested such as a holed-in anchor, chemical anchor and adhesives. As a result, a laminated rubber tile was designed with its upper layer constituted of a rubber sold on the market and its lower layer of a fiber reinforced rubber also on the market, and so was a shock absorbing type holed-in anchor. 1 ref., 11 figs., 4 tabs.

Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

Basic research on the carbon dioxide fixation using seaweed. Kaisorui no tansan gas kotei ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, M.; Ishihara, T. (The Kansai Electric Power Co. Inc., Osaka (Japan))

1993-08-25

Study was made for grasping the basic data of CO2 fixation technology by seaweed. The photosynthesis under the sea, which is different from that on the land, is judged to be made by taking in HCO3[sup -] and converting it into CO2 inside the plant. Porphyra yezoensis which is seaweed is cultivated as comestible. With a rise in CO2 content, the growth in length of leaves was observed to be accelerated through ventilating Porphyra yezoensis with the three test types of air which respectively contained 350ppm (atmospheric CO2 content), 1000ppm and 1600ppm CO2. As a result of measuring the photosynthesis speed by the generated quantity of O2, it was heightened with a rise in dissolved inorganic carbonic acid content of the sea water. Measurement was also made of daily fluctuation in calcification speed by Corallina officinalis capable of calcification by ventilating it with 350ppm and 1600ppm CO2. In case of 1600ppm, the sedimentation of CaCO3 was prevented. In case of 350ppm, the sedimentation was quantitatively larger during the bright period than that during the dark period. The growth of Gracilaria gigas which is an agar material was compared by changing the above CO2 levels. In case of 1600ppm, the weight grew to 2.3 times in 20 days. 16 figs., 2 tabs.

Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

Research on brake noise. Concerning LT drum brake; Brake noise ni kansuru kenkyu. LT Drum brake ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Chikamori, S; Shimizu, Y [Seikei University, Tokyo (Japan); Yano, M [Mitsubishi Motor Corp., Tokyo (Japan)

1997-10-01

The four degrees of freedom of shoe motion were adopted by considering the bending for the shoe vibration, and the simulation model was derived. Using this model, the mechanism by which the squeal is generated was reviewed. And conditions for the occurrence of squeal vibration were determined by a series of simulations. Then father analysis was conducted on the influences of various parameters upon the occurrence of squeal vibration. 2 refs., 10 figs.

Some considerations about improvement for fatigue strength of structures; Shatai kozobutsu no hiro kyodo kojo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kimoto, H; Toyama, K; Maruyama, H; Magara, S [Press Kogyo Co. Ltd., Kanagawa (Japan)

1997-10-01

To reduce weight, higher tensile strength and/or thinner plate are used or considered in vehicle structures. In general, welded or notch sections, fatigue strength decreases because of increasing concentrated stress or effect of notch sensitivity and so on. In this paper, some methods are studied to improve fatigue strength and obtain a long life. 2 refs., 11 figs., 5 tabs.

Report on reuse of concrete and masonry in foreign countries; Concrete no recycle ni kansuru kaigai no doko

Energy Technology Data Exchange (ETDEWEB)

Yamato, T. [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

1997-07-01

Referring to the report by RILEM in 1976, this paper introduces the status and guidelines on recycling concrete in foreign countries. In Flanders, Belgium, a sub-committee was established in 1990 under the auspices of Environment Agency and the Ministry of Construction. Researches and investigations have been carried out to prepare flexible guidelines so that reclaimed aggregates may be used in public constructions. The Belgian Road Research Center, the Belgian Building Research Institute and its subsidiaries are supporting several investigation and research projects. In England, about 10% of aggregates is estimated to have been made of wastes and recycled materials. The seventh revised edition of the expressway construction specifications in the concrete aggregate standard BS882 has approved for use as an aggregate for pavement concrete if quality of crushed concrete meets the quality and grain size standard of BS882. Additionally, this paper shows a list of specifications and standards for reclaimed aggregates made in the U.S.A., France, Germany and other countries. 18 refs., 3 tabs.

Study about the effect of microgravity on biofunctions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A study is made for the elucidation of the effect of microgravity on biofunctions. The protoplast of shiitake is exposed to microgravity and then cultured, and a significant difference occurs. The rate of colony formation by cell fusion in the test sector is found to be two times higher than that in the control sector. When swimming ciliates which are unicellular are suddenly exposed to microgravity, their swimming speeds changed differently according to the direction of swimming. When a mouse subjected to acupuncture for three days is exposed to microgravity, its water metabolism and excretory function are enhanced. A mouse treated with Chinese medicine reacts in the similar way. The change due to microgravity in the amount of acetylcholine in the hypothalamus is found characteristically time dependent. Mice infected with lethal herpes viruses just after exposure to microgravity die at a rate in proportion to the number of exposures and to the amount of viruses given. The migration speed of chemical stripes in case of a gel-base BZ (Belousov-Zhabotinsky) reaction under microgravity is equal to that on the ground. The trigger wave migration speed in case of a water solution-base BZ reaction under microgravity is reduced to approximately 80% of the speed on the ground. 12 refs., 31 figs., 3 tabs.

Technology assessment on a hydrogen fueled aircraft system; 1980 nendo suiso nenryo kokuki system ni kansuru technology assissment

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper describes technology assessment on a hydrogen fueled aircraft system. Indispensable as technological assignments are structuring different safety systems including prevention of leakage and ignition, not to speak of developing an airframe structure that considers cryogenic and brittle nature of liquefied hydrogen. Operation related industries would be subjected to increased burdens, such as purchase and servicing of new implements and materials, but the liquefied hydrogen industry will have a chance of growing largely with wide repercussions. In the environmental aspect, the aircraft will have less CO and SOx emission in exhaust gas and lower noise than the conventional jet aircraft. Technological problems to be solved in the development include the safety of fuel tanks, safety assurance measures, and liquefied hydrogen of the required amount to be supplied easily and at low cost. To meet these requirements, noticeable progress is demanded in hydrogen manufacturing technologies. What is also required is explosion-proof safety that does not have to require crews to take special considerations in take-off and landing, not to speak of during flight. This also applies to fuel feeding and servicing on the ground. Considerations must be given that rise in operation cost should not be excessive. (NEDO)

Heat transfer simulation in a furnace for steam reformer. Gas kaishitsu ronai no dennetsu simulation ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kudo, K; Taniguchi, H; Guo, K [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering; Katayama, T; Nagata, T [Tokyo Gas Co. Ltd., Tokyo (Japan)

1991-01-10

This paper discusses the heat transfer analysis in a furnace for LPG reforming to produce gas enriched hydrogen. The three-dimensional combined radiative and convective heat transfer processes in a furnace for LPG reforming is simulated by introducing the radiosity concept into the radiative heat ray method for an accurate radiative heat transfer analysis. Together with an analysis of the chemical reaction in the reactor tubes of the furnace, the heat transfer simulation gives the three-dimensional profile of the combustion gas temperature in the furnace, the tube-surface heat-flux distribution and the composition of the reformed gas. From the results of the analysis, it was clarified that increasing the jet angle of the heating burner raises the gas temperature and the tube surface heat flux near the burner entrance, and that the flame shape is the most important factor for deciding the heat flux distribution of the tube surface because the heat transfer effect by flame radiation is much more than that by convection of the combustion gas. 18 refs., 9 figs., 2 tabs.

Mechanical properties of weft knitted fabric reinforced composites. Iamimono kyoka fukugo zairyo no rikigakuteki tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Wu, W.; Inoda, M.; Kotaki, M.; Goto, A.; Fujita, A.; Hamada, H.; Maekawa, Z. (Kyoto Institute of Technology, Kyoto (Japan). Faculty of Textile Science)

1993-09-15

Mechanical properties and failure behavior of weft knitted fabric reinforced composites were studied. Aramid fiber was used as reinforcement (knitting fiber), and epoxy resin as matrix. Different tensions were applied to the weft knitted fabric in a course or wale direction to prepare 5 kinds of fiber reinforced composites with different densities of the knitted fabric, and tensile test pieces were thus provided by cutting each composite in a course or wale direction. As a result, the weft knitted fabric reinforced composite offered a dynamical anisotropy, and the tensile strength of the test pieces was higher in wale direction than course one. Fracture in a course direction occurred at the section with extreme low fiber content, while fracture in a wale direction occurred at a loop interlocking region due to stress concentration. The tensile strength was constant or increased in a course or wale direction by stretching the knitted fabric before molding, respectively. 21 refs., 15 figs., 2 tabs.

Fundamental characteristics on electric system of solar electric vehicle; Solar car no denki keito ni kansuru kiso tokusei

Energy Technology Data Exchange (ETDEWEB)

Fujita, S; Sasaki, M; Kaga, T; Koyama, N [Hachinohe Institute of Technology, Aomori (Japan)

1996-10-27

The electric system of a solar vehicle was removed and the fundamental characteristics examined in order to carry out a basic experiment on the electric system. Using a basic circuit with panels, batteries and loads connected, the voltage and current were measured in the presence/absence of the trackers, batteries, etc., and then, their effects were examined. Simultaneously, the quantity of solar radiation was also measured. The lowering of the output voltage was somewhat relaxed with the use of the trackers. Further, with the trackers used, the output voltage of the panel was small in spite of a large quantity of solar radiation compared to the case without the trackers, which was due to the restriction of the output voltage by the trackers. When measured without batteries, the output voltage of the panel was such that the load current was also influenced by the variation of insolation, so that, with a large decrease in insolation, the load current was decreased with the supply of current suspended from the panel. 7 figs., 1 tab.

On the relationship between stacking process and resolution. 2; Jugo shori to bunkaino ni kansuru kiso kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T; Miyazaki, M [Geological Survey of Japan, Tsukuba (Japan)

1997-05-27

With respect to concept of resolution in seismic exploration using the reflection method, detailed considerations were given on processes of forming the resolution as a result of arranging observation points at vibration transmitting and receiving points. In the discussion, numerical experiments were carried out, in which the scattering stacking process is applied in a model having one scatterer existing in homogeneous media. The experiments investigated an imaging formation process of the scatterer when arrangement of the vibration transmitting and receiving points were changed from a coarse condition to a dense condition while the number of transmitting and receiving points is being increased. Resolution is created if waveforms having finite frequencies are used as input, and the imaging is performed by utilizing the limited number of vibration receiving and transmitting points. If the concept of equi-travel plane is used under these conditions, the equi-travel planes perform negation with each other, and it was indicated that visual resolution is expressed by how good the negating effect is. It was discovered that such concept of the resolution is quite ambiguous in terms of engineerings. 2 refs., 17 figs.

Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

Study on grout-filled coupling steel sleeve; Kokan sleeve wo mochiita grout jutenshiki tekkin tsugite ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Y. [Osaka University, Osaka (Japan)

1997-06-01

Newly designed grout-filled coupling sleeve is discussed, which uses as the sleeve an electric resistance welded tube with protrusions formed in a checker pattern on its inner wall and is capable of using various premixed grouting materials available on the market. Specimens are subjected to uniaxial tensile loading and positive/negative cyclic loading, and the impact of various factors on the basic performance of the specimens and their stress/distortion characteristics at local spots in the reinforcing bar are disclosed. In the positive/negative cyclic loading in the plastic region, however, such findings are not obtained. In view of the stress/distortion characteristics at local spots in the reinforcing bar, a method is proposed for estimating the coupling strength and fracture type. A method for estimating the deformation behavior of the coupling, however, is not proposed. Investigations are conducted into the manufacture and installation of the grout holding framework, coupling fixing jigs, plugs, etc., and it is found that precasting should be studied in the future. 38 refs., 156 figs., 30 tabs.

Performance analysis on natural energy autonomous house (HARBEMAN house); Shizen energy jiritsu house (HARBEMAN house) ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1996-10-27

To reduce fossil fuel consumption and CO2 emission, this article introduces an actually constructed natural energy autonomous house. It has a solar collector on the south roof for hot water supply and a sky radiator on the north roof for cooling water supply. The sky radiator uses radiation cooling phenomena into the space by electromagnetic wave through the window of atmosphere. This house also has an insulated tank with a capacity of 31 m{sup 3} in its underground. In the long-term heat storage mode, the heat is collected through the solar radiation during the period from summer to spring and is stored in the underground water tank, to use it for heating and hot water supply in winter. The heat can be recovered from the garbage waste incinerator. A gas fired auxiliary boiler is used for the shortage. In the long-term heat regeneration mode, the heat is regenerated through the sky radiator during the period from spring to summer and is stored in the underground water tank, to use it for cooling in summer. For the shortage, the water is cooled using a heat pump operated by the midnight power. The insulating performance is improved by using the pair glass in windows and the glass wool in the walls. Rain water is collected in a tank with a capacity of 2 m{sup 3}, to use it for toilet water. Annual energy and water saving is equivalent to 600,000 yen. 10 refs., 10 figs., 2 tabs.

Study on molecular controlled mining system of methane hydrate; Methane hydrate no bunshi seigyo mining ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kuriyagawa, M; Saito, T; Kobayashi, H; Karasawa, H; Kiyono, F; Nagaoki, R; Yamamoto, Y; Komai, T; Haneda, H; Takahashi, Y [National Institute for Resources and Environment, Tsukuba (Japan); Nada, H [Science and Technology Agency, Tokyo (Japan)

1997-02-01

Basic studies are conducted for the collection of methane from the methane hydrate that exists at levels deeper than 500m in the sea. The relationship between the hydrate generation mechanism and water cluster structure is examined by use of mass spectronomy. It is found that, among the stable liquid phase clusters, the (H2O)21H{sup +} cluster is the most stable. Stable hydrate clusters are in presence in quantities, and participate in the formation of hydrate crystal nuclei. For the elucidation of the nucleus formation mechanism, a kinetic simulation is conducted of molecules in the cohesion system consisting of water and methane molecules. Water molecules that array near methane molecules at the normal pressure is disarrayed under a higher pressure for rearray into a hydrate structure. Hydrate formation and breakdown in the three-phase equilibrium state of H2O, CH4, and CO2 at a low temperature and high pressure are tested, which discloses that supercooling is required for formation, that it is possible to extract CH4 first for replacement by guest molecule CO2 since CO2 is stabler than CH4 at a lower pressure or higher temperature, and that formation is easier to take place when the grain diameter is larger at the formation point since larger grain diameters result in a higher formation temperature. 3 figs.

Performance test of deodorants for ammonia gas; Ammonia gas ni taisuru dasshuzai no seino kentei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yano, H.; Hashimoto, S.; Yonemura, S. [Shimizu Corp., Tokyo (Japan); Shoda, M. [Tokyo Institute of Technology, Tokyo (Japan)

1998-01-10

This paper presents the results of performance tests of various kinds of adsorbents by static and dynamic adsorption methods to select the optimum deodorant (adsorbent) for ammonia gas (NH3). In the performance test of the static adsorption method, the amounts of NH3 adsorbed by 21 kinds of adsorbents including physical and chemical adsorbents were measure. The amounts adsorbed physical adsorbent No. 6, chemical adsorbents Nos. 18, 19 and 20 which showed higher adsorption ability were 0.0160g/g, 0.0284g/g, 0.0250g/g, and 0.0249g/g respectively at 30degC under equilibrium pressure of 50 mmHg. All of the adsorbent showed in Freundlich`s adsorption isotherm for NH3. Although the correlation between specific area, pore volume, mean pore radius, pH each adsorbent and the amount of adsorbed were tried, the correlation between the pH and the amount of NH3 adsorbed was significant. This suggests that the pH is a proper criterion for selection for adsorbents. The performance test of the dynamic adsorption method, was conducted for adsorbents Nos. 6, 18, 19 and 20 above-mentioned. The 10% breakthrough time was compared as the performance index. The breakthrough time of the adsorbent which the amount adsorbed was large was long but the breakthrough time was not proportional to the amount adsorbed. These results suggest that the performance test only by the static adsorption method is insufficient and that the breakthrough time test by the dynamic adsorption method is essential. 13 refs., 10 figs., 4 tabs.

Primary study on quantitative evaluation of driver fatigue; Unten hiro no teiryo hyoka gijutsu ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Noguchi, Y; Mochizuki, M; Toyofuku, K [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Katsuura, T [Chiba University, Chiba (Japan)

1997-10-01

Quantitative evaluation of physical and mental loads are effective in developing more human-friendly vehicles. Here attention has been focused on the mental load. Attempts were made to find some physiological indices that can be used for quantifying the mental load and resultant fatigue. Subjects were told to perform three different tasks in a climatoron, and the relation between physiological indices and their perception of fatigue as well as their capability of performing the tasks were analyzed. As a result, heart rate variability is a good index for quantitative evaluation of mental load and fatigue. 5 refs., 4 figs., 6 tabs.

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen gas turbine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso gas turbine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-31

This research aims at establishment of the meaning of using hydrogen as gas turbine fuel in the hydrogen energy system and various conditions for hydrogen gas turbines, and approaches to the feasibility study and R and D of hydrogen gas turbines in the future. In fiscal 1975, researches were made on (1) feasibility study on hydrogen-oxygen gas turbine, (2) establishment of various conditions for technical, social and economic realization of hydrogen gas turbines in the total energy system, and (3) study on technical troubles to be solved for realization of hydrogen gas turbines. For the above researches, study was made on hydrogen combustion based on the hydrogen combustion test result of gas mixture including hydrogen, and on the feasibility of aphodid cycle. In addition, study on the applicability of hydrogen-oxygen gas turbines, comparative study on hydrogen-oxygen gas turbine, MHD power generation and fuel cell, and the future prospect of hydrogen gas turbines for ships were made to place this hydrogen gas turbine. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-04-20

Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

Investigations on steel slag re-utilization in developing countries; Hatten tojokoku ni okeru tekko slag sairiyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to promote steel slag re-utilization in developing countries, a possibility was presented for technical cooperation to India, Indonesia and Thailand upon putting the status of slag utilization in Japan into order. Blast furnace slag produced in Japan (having a re-utilization rate of 95%) is re-utilized and processed as cement aggregates and road beds, and converter slag as civil engineering materials and ores. Steel making slag (having a re-utilization rate of 80%) is re-utilized as road, processing and civil engineering materials. Since the steel making slag faces intensifying competition with ash made by incinerating construction and general wastes, it is important to improve its price competitiveness or mixed utilization with other materials. Re-utilization has not advanced to a recognizable level in developing countries because of having no difficulty for availability of lands for wastes. However, growth of full-scale steel industries and elevation in tendency of environment preservation now urge increase in the slag re-utilization rate. Required to achieve the goal would include wider use of re-utilization technologies, quality control on slag, joint use of facilities to produce re-utilization products, and governmental assistance on burdens of transportation cost. Assistance from Japan is expected to help meet these requirements. 25 figs., 31 tabs.

Committee report on visual appearance of neon lights. Neon no hikari no miekata ni kansuru tokubetsu kenkyu iinkai hokoku

Energy Technology Data Exchange (ETDEWEB)

Kansaku, H. (Chukyo University, Nagoya (Japan). Faculty of Letters)

1991-04-25

Were summarized the results of experiments and literature searches, conducted by the Commettee on Visual Appearance of Neon Lights,'' which was set up to provide scientific and basic data for understanding of relationship between neon lights and psychological reaction of human, and for realizing of neon sign advertisements with playing a role as neon lights and without any environmental problems. Analytical results of influences of six colors, such as red, yellow, green, blue, violet, and white, brightnesses, and flickering frequencies to the psycological reaction of human on the direct observations of neon lights were described. Results of influences of the neon light incidence into the room to the psychology of residents were also introduced. Furthermore, evaluation of neon lights as an aspect was discussed. Consequently, based on the combination of activity and estimativity, some attentions to be payed on the setting-up of neon lights were pointed out. A red flickering neon light'' was given as clearly a bad example. 2 figs.

Survey on bio-chemical complex harmonized with global environment. 3; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A survey was conducted of bio-chemical complex harmonized with the global environment for the purpose of constructing the material production process harmonized with the environment by the process fusion between biological conversion and chemical reaction. Palm oil was taken up as renewable raw material plant resource. The process utilizing bio-chemical reaction advances at normal temperature and pressure and is high in reaction specificity and selectivity. This is a recycling, circulation and environmental harmony type production technology which brings high yield, energy conservation, resource conservation, and low environmental loads. Waste water treatment and production of useful substances from sludge were thought as elementary technology. A possibility was studied of enzyme production by culturing solid waste, and the enzyme was applied to the hydrolysis process. The paper indicated trace components in the palm oil and the extraction method and proposed the production process of new derivatives for adding value to hydrolysate. A study was also made of the overall process flow which integrated these new processes and the material balance. The comprehensive evaluation of this new process was made from the aspect of the product structure, the market, construction cost, economical efficiency, and the environment. 133 refs., 65 figs., 56 tabs.

Subjects on geochemical technology for geothermal power plant. Chinetsu hatsudensho ni okeru kagaku kanri gijutsu ni kansuru shomondai. 1

Energy Technology Data Exchange (ETDEWEB)

Hirowatari, K [Kyushu Electric Power Co. Ltd., Fukuoka (Japan)

1991-04-30

This paper introduces the following technologies and countermeasures found to be successful in solving geochemical problems relating to the maintenance and management of geothermal power plants belonging to Kyushu Electric Power Co., Ltd. In controlling condensate properties,curtailment of pH fluctuation range by changing the injection point of NaOH,inactivation of sulphur bacteria by using chloramphenicol and prevention of slime loading of the condenser strainer by running of the cooling tower without make-up water were achieved. In the environmental countermeasures,it was concluded that Fe-ion injection method was most effective to remove As out of waste hot waters which are all reinjected into the underground formation now. By understanding the characteristics of the well eruption fluids,the attenuation mechanism of steam producing wells could be estimated, which were interference,re-eruption and degradation of the reservoir temperature caused by the reinjected hot waters. And the problems associated with the attenuation of steam producing wells have been solved fundamentally by taking proper countermeasures to eliminate the influence of reinjected hot waters. The atteunuation of reinjection well was found to be caused dominantly by silica loading at the permeable zone of wellbore and to be effectively solved by high temperature reinjection of the waste hot waters, controlling of temp. degradation of hot waters to be reinjected and prevention of air mixing. After applying proper countermeasures, the attunuation rate of the reinjection well has been fairly improved. 13 refs., 21 figs., 2 tabs.

Study on evaluating method for earthquake resisting performance of steel piers; Kosei kyokyaku no taishinsei ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Isoe, A.; Hashimoto, Y.; Morimoto, C.; Sakoda, H.; Ishige, T.; Yoshikawa, T.; Kishida, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1998-12-20

After the shock of Hyogoken Nanbu Earthquake in 1995, protection against level 2 earthquake becomes important subject for civil structures. Subsequently plastic design methods for steel piers have been studied and rapidly introduced. The authors developed a method to evaluate the earthquake resisting performance of a steel pier with a single mass model. This model is useful for design because of its simplicity but on the other hand it can not consider the effects of piers` interaction in space. To include this effect in an analysis a simple 3 dimensional calculation model of box-column pier is developed. (author)

Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

Investigations on international standardization of environmental management systems. 3; Kankyo kanri system no kokusai hyojunka ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Japan as an ISO member country identifies the state of discussions in the environmental management standard deliberation committee at ISO. Investigations were performed on international standardization of environmental management systems for the purpose of participating and cooperating in preparing and establishing international standards related to environmental management, and playing part in working, solving and improving environmental problems. Under the circumstances that environmental problems are drawing worldwide interest, the International Organization for Standardization (ISO) has been carrying out since 1993 deliberations on environmental management standards to institutionalize environmental management rules to check effects of business activities on the environment. The International Organization for Standardization/Environmental Management Technical Committee (ISO/TC207) was installed, at which series number of 1400 order was allotted for environmental management related standards, and major standards have come to a final stage of standard formulation at the TC207 Oslo conference in June 1995. In Japan, the Ministry of International Trade and Industry has established an environmental management standard deliberation committee composed of people of experience or academic standing to advance discussions on how the environmental management should be in business entities through deliberations on ISO standards.

Investigations on installation of the heat exchange system in geothermal wells; Chinetsu koseinai netsukokan system donyu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The heat exchange system in geothermal wells is a system that replaces the air source heat pump and uses underground beds or groundwater as a heat source to heat rooms by collecting underground heat in winter, and cool rooms in summer by operating a heat media circuit in reverse direction through the action of a reverse flow valve to discharge heat underground. This paper describes feasibility investigations on the system including its technical trend for introducing the system technology. Technological and economic discussions were given by classifying the intra-well heat exchange device in its installation direction (horizontal loop type and vertical installation type), underground heat exchange media (antifreeze solution/water cyclic system and direct expansion system), and underground heat transfer (heat conduction system and heat convection system). As a result of discussing each system, it was concluded that the following two systems are promising: A = vertical installation, antifreeze solution/water cyclic and heat conduction system, and B = vertical installation, antifreeze solution/water cyclic and heat convection system. Since the system B was found to have better efficiency and economy among both systems, it is necessary to verify an intra-well heat exchange system and operation methods that suit the system B effectively. 21 refs., 8 tabs.

Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatani, T. [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K.; Moriyoshi, N. [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T. [Nagoya Institute of Technology, Nagoya (Japan)

1996-12-31

Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N; Omata, K [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

Consideration on local blast vibration control by delay blasting; Danpatsu happa ni yoru kyokuchiteki shindo seigyo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Mogi, Gento; Adachi, Tsuyoshi; Yamatomi, Jiro [The University of Tokyo School of Engineering Department of Geosystem Engineering, Tokyo (Japan); Hoshino, Tatsuya [Mitsui Mining and Smelting Corp., Tokyo (Japan)

1999-10-31

In this research, local blast vibration control based on the theory of superposition of waves was investigated. Firstly, the influence of delay time errors of conventional electric detonators upon the level of local blast vibration was examined. Secondly, for a further effective local blast vibration control, a new delay blasting design concept 'combined delay blasting' that postulates the use of electronic detonators, which virtually have no delay time errors, is proposed. For a delay blasting with uniform detonation time intervals, an optimum time interval to minimize the local PPV (Peak Particle Velocity) is obtained based on the relationship between the PPV and the time interval, which is derived by superposing identical vibration time histories of each single hole shot. However, due to the scattering of the actual delay time caused by errors, PPV of a production blast seldom coincides with the estimated one. Since the expected value and the variance of PPV mainly depend on sensitivity of PPV around the nominal delay time, it is proposed that not only the optimum but also several sub-optimum candidates of delay time should be examined taking error into consideration. Concerning the 'combined delay blasting', its concept and some simulation results are presented. The estimated reduction effect of blast vibration of a delay blast based on this concept was quite favorable, indicating a possibility for further effective local blast vibration control. (author)

Study on torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kojima, N; Kishimura, K [Meiji University, Tokyo (Japan)

1996-10-27

Discussing the rotor blades of the torsion arc blade type (TABT) wind turbine, difference in windmilling characteristics was determined between elliptic blades and rectangular blades by theoretical analysis and model experiment. Experimental generation of power was carried out using a test wind turbine in the natural wind. First, elliptic blades were bent into arcs and fixed to shaft. The action force was determined calculating the blade area and the wind velocity vertical thereto. Furthermore, the force in the direction to turn the rotor was determined with the effect of the part behind the blade taken into account. The rotation-curbing air resistance in the flank direction that a rotor experiences was subtracted to determine the torque generated. A formula was derived for the elliptic blade. Second, a formula was derived in the same way for the case of rectangular blades. In conclusion, in the case of 6-blade wind turbine, the rate of responsibility for wind turbine rotation of the part behind the blade was approximately 50% of the part in front of the blade. Shape coefficients were introduced into the theory, which resulted in values agreeing well with values obtained from experiments. Elliptic blades yielded more power than rectangular blades at the same wind velocity. High in durability, the TABT wind turbine is expected to be put into practical use as a compact auxiliary power generating device. 2 refs., 14 figs.

Evaluation on lifetime risk in reinforced concrete structure; RC kozo no lifetime risk no hyoka ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, M. [Public Works Research Institute, Tsukuba (Japan); Adachi, H. [Taisei Corp., Tokyo (Japan); Akakura, Y. [Ministry of Transport, Tokyo (Japan); Ibayashi, K.; Ozaka, Y. [Tohoku Gakuin Univ., Sendai (Japan)

1996-02-15

To evaluate the risk during longevity of reinforced concrete structure subjected to earthquake motions, called lifetime risk, damage and safety were estimated by means of the earthquake risk analysis and earthquake response analysis. For the earthquake risk analysis, historical earthquake data with relatively low accuracy were efficiently taken into account, to determine the annual mean generation probability against the earthquake motion strength in ten main cities. A new damage index with load hysteresis was defined as an anti-earthquake evaluation index where accumulative damage is taken into consideration. Assuming that the damage transits from `certain state` to `certain state` every time the earthquake motion generates at the noticeable place, damage transition matrix expressing transition probability was calculated by using the results of earthquake risk analysis and the accumulative damage index. The lifetime risk was calculated from the damage transition matrix and the earthquake motion generation probability, to evaluate the safety. 21 refs., 10 figs., 8 tabs.

Comparison about the bone material examination of JIS and ISO; Honezai shiken ni kansuru JIS to ISO no hikaku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Sumie.; Yanagi, Kei.; Shimura, Akiharu.; Murohoshi, Shiori. [Japan Testing Center for Construction Materials, Tokyo (Japan)

1998-12-01

There are various things in slug bone material and so on manufactured from the macadam, crumble sand. Which crushed rock including gravel, sand to produce in the nature and which was manufactured, and a lightweight bone material and the industry by-product with the bone material used for the concrete. It is necessary with a bone material to grasp the nature of the bone material itself properly to occupy about 70% of the capacity in the concrete and to manufacture the good concrete of the quality from the influence that influence to the various concrete materiality that quality being big. When the quality of a bone material to use for the concrete is confirmed, an examination is being done in accordance with the way of examining it established as the Japanese industry standard in our country. (NEDO)

Investigational study on construction of the physical function database; Shintai kino data base no kochiku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

An investigational study was carried out on construction of the physical function database which can supply data useful for planning, design and production when companies provide products and barrier-free environment for the aged society. Up to now, the final image of database was studied as to the visual function. In addition, this study is aimed at constructing the physical function database. In the literature survey, basic data on physical characteristics of the aged which have lain scattered were collected and systematically sorted in relation to the exercise function in order to make an analysis of the data and measuring technology in terms of reliability, importance, and applied values. In the survey of corporate needs, an examination of concrete needs for the exercise function and auditory function was made for general companies and companies related to the medical and welfare apparatus field. As to the visual function, a study was conducted on selection of new items for visual measurement and measuring methods. In the study of the database structure, a pilot database was constructed and subjects were extracted. 529 refs., 57 figs., 15 tabs.

Report on the actual situations of the commercially applied, industrial robots; Sangyoyo robot ni kansuru kigyo jittai chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

Described herein are the actual situations of industrial robots as the FY 1991 questionnaire survey results. The questionnaires were sent to 541 factories, and 74% thereof were recovered. The major machine types fall into categories of manual manipulator, stationary sequence manipulator, remote controlling robot, sequence robot, playback robot, numerically controlling robot and intelligent robot. They are mainly driven by hydraulic, pneumatic, or electrical power. Their mechanism types cover polar coordinate, cylindrical coordinate, rectangular coordinate and articulation types, among others. They are mainly controlled by electronically, electrically (hydraulic or relay), or pneumatically. The major purposes for general works include casting, forging, resin processing, heat treatment, pressing, welding, coating, machining, cutting, assembling, reception/delivery of goods, and testing/inspection. The special works they are in service include those for power/gas/water services, construction works, and research and development. By work step, they are in service, e.g., for loading/unloading goods, palletising/packing goods, supporting, screening, welding, spraying/coating, grinding, clamping, assembling, and riveting. (NEDO)

Investigation on vibrational dampers for cables of Tsurumi Tsubasa bridge; Tsurumi tsubasabashi no keburu seishin hoshiki ni kansuru jisho

Energy Technology Data Exchange (ETDEWEB)

Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Public Corp., Tokyo (Japan); Yamada, H. [Yokohama National Univ. (Japan)] Murakami, T. [NKK Corp., Tokyo (Japan). Applied Technology Research Center

1998-03-20

In a long cable-stayed bridge, countermeasure against wind induced vibration should be often taken at the same time together with the measure against angular bent phenomena (phenomena in which secondary bending stress is generated on the front of fixing socket by live load). The conventional countermeasure is a combined use of buffer rubber and dampers. This study points out problems in the conventional countermeasure on the application to the cables of the Tsurumi Tsubasa Bridge and combination of dampers and angular bending buffer device is examined. The result shows that a combined use of high-damping rubber and oil dampers enables installation of the dampers in a lower position while maintaining the performance and is excellent in the easiness in installation and maintenance and in aesthetic view. This system was applied to the Tsurumi Tsubasa Bridge and the effectiveness on damping and angular bending relaxation was confirmed through the model tests, and vibration tests and field observation on the cables. 9 refs., 20 figs., 7 tabs.

Study of hydrogen engine for a hybrid electric vehicle. 1; Hybrid denki jidoshayo suiso engine ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Iguchi, T.; Numata, T. Hiruma, M.; Yamane, K.; Nakajima, Y.; Furuhama, S. [Musashi Institute of Technology, Tokyo (Japan); Takagi, Y. [Nissan Motor Co. Ltd., Tokyo (Japan)

1998-10-15

Study was made on application of a hydrogen engine to series hybrid electric vehicle (SHEV). Power of 20kW (for steady driving of a vehicle of 1t in total weight on flat road surface at 100km/h), and NOx emission concentration equivalent to that of EZEV (equivalent zero emission vehicle) were used as target performance. One of the merits of using a hydrogen engine for HEV is that conventional high-reliability gasoline engines can be used as hydrogen engines only by a bit of modification. A modified conventional 4-cylinder 4-cycle gasoline engine was used for this study. Hydrogen gas was continuously supplied through an intake manifold for premixed combustion by spark ignition. Brake thermal efficiency was improved from 30.5% to 35.5% by use of a high compression ratio and reduction of friction loss. NOx emission concentration could be controlled within 10ppm by ultra-lean combustion even at excess air ratios over 2.5. Both high efficiency and low emission were achieved at the same time around 3000rpm in engine revolution. 4 refs., 12 figs., 1 tab.

Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakatani, T [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K; Moriyoshi, N [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T [Nagoya Institute of Technology, Nagoya (Japan)

1997-12-31

Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

Fiscal 1995 investigation on biological fixation of carbon dioxide; 1995 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To cope with the global warming caused by CO2, an investigation was conducted into biological fixation. It is necessary to make a many-sided and comprehensive study on the mechanism of CO2 fixation, the scale (area and carbon holding density), the rate and the environmental impact of the introduction of the technology and the technical problems, and to make a quantitative evaluation of each of the methods in order to make them practical proposals. The global ecosystem is classified into the land biota and ocean biota, and each typical ecosystem was surveyed in terms of the surface area, the carbon holding amount (presently existing amount), the net primary production amount, the required nutrient salt amount, the transpiration rate, etc. Next, a discussion was made on the increasing effect of the carbon fixation amount by changing the present ecosystem from the aspect of scale and rate. At the same time, a study was carried out of energy efficiency, economical efficiency and problems. Last, elementary technology was taken up which seems to be important for implementing measures for the biological carbon fixation. As to the ocean, it is necessary to obtain information, which is not sufficient to utilize marine biota for CO2 fixation, especially on the mechanism of depth-direction transfer of organism and its quantitative grasp. As to the land, one of the measures is conversion of the ecosystem where the amount of carbon fixed is small to the ecosystem where the amount is large. 249 refs., 58 figs., 51 tabs.

Study on fault diagnostic system using modularized knowledge; Mojuru gata chishiki wo mochiita ijo shindan system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimada, Y.; Sayama, H.; Suzuki, K. [Okayama Univ. (Japan). Dept. of Industrial and Mechanical Engineering

1997-08-15

Recently, a fault diagnostic expert system was prosperously developed as an objective of chemical plants and nuclear power plants. In this paper, a fault diagnostic method using modularized knowledge was proposed, a fault diagnostic system was constructed for an experimental plant, and the effectiveness of this method was clarified by carrying out a fault diagnostic experiment. The characteristics of the proposed fault diagnostic system were as follows: The necessary knowledge for diagnosing faults was made into each process element. Based on this method, the revision and addition of a knowledge base could be carried out in each element, and the design change of a plant could be flexibly corresponded by only changing the related part of the process flow graph. The estimated results were stored into the working memory, not only faults of an element in which faults resulted could be estimated, but also the fault propagating path could be clarified. 8 refs., 6 figs., 3 tabs.

Robust estimation of space influence model. Part 2. ; Synthesis of urban lattice data analysis for practical use. Kukan eikyo model no antei suiteiho. 2. ; Jikkenteki mesh data kaiseki system kochiku no tameno kukan sokan bunsekiho no taikeika

Energy Technology Data Exchange (ETDEWEB)

Aoki, Y.; Osaragi, T. (Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering)

1991-07-30

In this study, a method for robust estimation of parameters of the space influence function model, which was possible to become unstable, was investigated by applying a principal component method. In order to carry out the robust estimation of parameters without the effect of multicollinearity, regression coefficients of principal components with small eigenvalue and with small single-correlation with dependent variables were required to forced to be zero in the estimation method by principal component. Through the case study using the real urban lattice data, the conventional method was compared with the principal component method. As a result, the latter method realized the excellent sabilization of spatial distribution patterns of estimation parameters and the simple interpretation of parameters. It also improved reliability since 95% confidence interval of the estimated value became smaller. This method was found to be effective as a basic measure to acheve the stability of parameters. 10 refs., 7 figs.

Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on peripheral technologies around hydrogen); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

This report summarizes the fiscal 1975 research result on peripheral and seed technologies for hydrogen energy systems. Chapter 1 'Evaluation method for thermochemical techniques' reports critical study on qualitative evaluation method, estimation method for thermal efficiencies, and trial cost calculation example. Chapter 2 'Current state and problems of water electrolysis and hybrid technique composed of electrolysis and thermochemical technique' reports general survey on current water electrolysis and new technologies under development to clarify possible electrolytic voltage drop, from the practical viewpoint. Chapter 3 'Use of a high- temperature gas cooling reactor for hydrogen production' reports survey on the current and future reactors, and characteristics of such nuclear reactors, from the viewpoint that study on thermochemical technique is dependent on use of a high-temperature gas cooling reactor. Chapter 4 'Hydrogen transport and storage technology using organic compounds including oxygen' reports that acetone-isopropanol system is better for hydrogen storage. Chapter 5 'Water electrolysis using photo-semiconducting electrode' reports the additional survey. (NEDO)

Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen engine for aircraft); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kokukiyo suiso engine ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-01

This report summarizes the research results on (1) the prospect of an aviation system based on hydrogen energy, (2) the total system of aircraft based on hydrogen energy, and (3) the performance, structure and specifications of airplanes and engines using synthetic fuel such as hydrogen. In (1), study was made on air transport energy, and prediction was made on the demand of liquid hydrogen assuming conversion of petroleum fuel into hydrogen fuel in the future. In (2), the supply system of liquid hydrogen is essential in conversion of current aircraft fuel into liquid hydrogen. Such supply system over the world is also necessary in conversion into liquid hydrogen for both domestic and international airlines. In (3), in order to discuss the feasibility of liquid hydrogen fuel aircraft, the merit of such aircraft as compared with current aircraft using JP fuel, and whether designing a new airframe or modifying existing airframes, study was made conceptually on the size and capacity of airframe by statistical treatment and analysis of previous conceptual designs. (NEDO)

Studies on factors of disorder and regularity in the streeet view. Part 1. ; Studies on disorder and regularity in the central business district. Gairo keikan no ranzatsuter dot seizensei yoin ni kansuru kenkyu. 1. ; Chushin shigaichi ni okeru ranzatsuter dot seizensei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsunoto, N; Teranishi, N; Senda, M [Nagoya Institute of Technology, Nagoya (Japan). Faculty of Engineering

1991-11-30

This study intends to identify the visual confusion in spatial views by the routine human conveption of regularity and disorder, and elucidate physical factors that cause the disorder and regularity in street views. The disorder factors include the additions annexed to the view afterwards, and the regularity factors include those flat objects that decide the pattern of a view. Many factors can be either disorder or reguarity factors according to their sizes, how they look, and how they are affected by surrounding objects. The disorder in a street view is approximately determined of its degree by such distribution patterns as the spread and convergence of the disorder factors. The disorder can be intensified stronger by the spread of the factors widely over an entire area or the existence of objects that give disorderly impressions, rather than by the number of disorder factors. The regularity is affected easily by the disorder factors, it being lowered by intensities of the disorder. The deciding factors for the disorder or regularity are the kinds of objects, how they are laid out and what they are surrounded with. The factors that govern the degrees of the disorder and regularity are how large the area they are distributed in, the number, how they look, and where they are positioned. 24 refs., 9 figs., 6 tabs.

Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

Survey of pollution-resistant plants and their cultivating techniques; Osen busshitsu taisei shokubutsu to sono shokusai gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The reduction of forests due to environmental pollution has been surveyed, to investigate the pollution-resistant plants and solid microorganisms. In Japan, the blight of needle-leaf trees (pine and momi fir) and of Japanese oak has occurred, and blight of some other trees, such as wild cherry trees, Japanese apricot trees, birch, Japanese cedar, cypress and bamboo, has been reported from various regions. In this article, plants reported to be resistant to pollutants are listed, and the physiological features of these plants are described. Furthermore, to develop pollution-resistant plants, reports relating to clarification of the mechanism of resistance development and the genes involved are reviewed. Microorganisms which symbioses for roots support these root functions. They also suppress the activity of pathogenic microorganisms and improve the environment around the roots, thus helping plants to grow normally. The roles played by symbiotic microorganisms and how to utilize these organisms are discussed. Their functions in coping with acid rain and heavy metal pollution, and how to utilize such functions are also discussed. 707 refs., 13 figs., 13 tabs.

Study on the cutting behavior of plasma sprayed ceramic coatings. Plasma yosha ceramics himaku no sessaku kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Inui, Y; Kubohori, T; Ikuta, T [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1992-09-30

Fracture behavior of Al2O3-TiO2 sprayed ceramic coating was investigated at low cutting speeds when using two dimensional cutting. Scanning electron microscope was used to observe the generation, development and propagation of cracks during cutting. Small cracks and fracture have been developed in the cutting groove along the cutting direction, and there has been many fractures in spray particles unit. In the initial stage of cutting, radiant cracks have developed on the sprayed coating, however, linear big cracks starting from the cutting edge towards the cutting direction, have developed. The cracks have developed along the grain boundary of coating component, and cracks progressed along the portion with weak bonding force. When the depth of the cut was under 5[mu]m, the cutting face has formed many microfractures, and the cutting has been very stable. It has been necessary to select the cutting conditions that do not cause big fracture, microcutting and so on, in order to achieve favorable surface condition with minor fractures. 8 refs., 13 figs., 2 tabs.

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

Performance analysis on natural energy autonomous house, HARBEMAN house; Shizen energy jiritsu house (HARBEMAN house) no simulation ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujino, T; Saito, T [Tohoku University, Sendai (Japan)

1997-11-25

Outlined herein are a procedure developed to simulate performance of an energy-autonomous (independent) solar house referred to as HARBEMAN HOUSE (HH) built in 1996 in City of Sendai, comparison between the simulated and observed results, and characteristics of the solar house. The house is equipped with a solar collector and sky radiator, both installed on the roof, the former facing south to collect solar energy and generate hot water whereas the latter facing north to radiate heat and generate cool water. Both are connected to an underground heat-insulated tank having a capacity of 31m{sup 3}, which stores hot or cool water to keep their conditions for extended periods. The solar system operates in heat- or cool-storage mode. In the heat-storage mode, quantity of heat stored increases, although at a slow rate, as tank capacity increases. In the cool-storage mode, on the other hand, quantity of cool stored increases in proportion to tank capacity. This is because solar energy is collected throughout the year whereas cooling by radiation is concentrated in early spring. Loss rate of heat stored increases as tank capacity increases, and the opposite trend is observed with cool stored. 12 refs., 7 figs., 2 tabs.

Study on the effect of micro-gravity on bio-functions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The effect of micro-gravity on bio-functions and vital reaction was studied using the facility of Underground Gravity-free Experiment Center Co. On the effect on osteoblast shape and gene expression, although fluorochrome reacting with Ca was well taken into cells, no significant difference in Ca content in cells was observed before/after falling. Expression of genes related to cell propagation was controlled under micro-gravity. Protoplast fusion of Lentinus was unaffected by micro-gravity. The mRNA fragments of gravity sensitive mutant of rice plant were affected by micro-gravity. Paramecium was set swimming in solutions with different specific gravities. The reaction behavior of Paramecium was affected by the difference in specific gravity between cell bodies and solutions. The water content metabolism functions of a mouse with needle stimulus, in particular excretory, were slightly promoted by micro- gravity. The cortisol level in blood of a falling mouse group rose showing strong stress. As the preliminary study on the geotaxis of insects, motion of bagworm was observed. 12 refs., 38 figs., 4 tabs.

Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by Optoelectronic Industry and Technology Development Association as part of the cooperation programs, for establishing the Asian environmental information networks. It outlines the research cooperation project for the environmental networks, results of the 4 on-the-spot surveys, 2 occasions for inviting researchers to Japan, and construction of the internet and Asian environmental information network systems. (NEDO)

Outline and summary of research for a database of unused energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For effective promotion of the new energy utilization project of NEDO and preparation of the future new energy vision, the data on unused energy were systematically arranged. The definition of heat supply systems using unused energy was clarified, and the kind and property of unused energy were arranged. Some typical systems of heat supply facilities using unused energy were presented. The data were classified by energy source, temperature level and region, and the detailed database was prepared for the typical systems. The overseas database was prepared, in particular, for European and American systems. Domestic and overseas policies, laws and subsidy systems were arranged. The introduction effect of two heat supply facilities using unused energy was surveyed, and their operation costs were analyzed. Basic terminology related to unused energy was compiled and explained. Related organizations, in particular, manufacturers were surveyed and arranged. The main manufacturers of a heat recovery refrigerator and waste heat boiler as typical equipment, and the number of these equipment shipped were arranged. 51 figs., 116 tabs.

FY1995 study of feedback type gait training system; 1995 nendo feedback gata hoko kuren sochi ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this project is to develop and demonstrate the utility of feedback type gait training equipment designed for the measurement and evaluation by a walking training of the aged or patient. As similar concepts of walking training, a locomotion in the water for the aged is applied in rehabilitation. Our development of this study established the system of a suspending mechanism which revolves around the prop, and a walking on the circular type force plate by the aged or patient. It is possible to detect a walking reaction force of several patients from force plate simultaneously. And then, the data from force plate makes feedback signal to put up the patient like a buoyancy in the water. Concerning the evaluations of walking pattern a step range, a hanging ratio and a walking speed, etc. are acquired for each patient by the acknowledgment base. This system is actively able to perform a walking training continuously compared with conventional passive gait equipment. (NEDO)

Research on crystal growth by using pressure as a control parameter; Atsuryoku seigyo ni yoru kessho seicho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-31

This research project aims to establish a technique for crystal growth using pressure as a principal control parameter, and combining it with a microgravity condition, to develop a novel process material fabrication. Since the solubility of materials depends on pressure, it is possible to control a supersaturated condition for crystal growth by changing pressure. The growth condition can be controlled precisely, which is not possible by conventional methods that vary temperature and other factors. On the other hand, because a concentration diffusing field is formed autonomically around crystals in association with their growth, density convection is generated under gravity as a result of difference in the concentrations, making the growth conditions severely complex and uncontrollable. Ideal crystal growth condition control may be possible if the pressure control is performed under micro-gravity by which generation of the density convection can be suppressed. Realization has been achieved on in-situ observation by using high-magnification microscope which uses a diamond anvil cell, development of a hydraulic type optic pressure cell, and a high- speed crystal growing technology by means of pressure control utilizing the cell. New findings were also obtained on effects of pressure on crystal forms, and the pressure induced solid phase transfer mechanism. 67 refs., 49 figs., 3 tabs.

Demonstrative study for the wind and solar hybrid power system. 2; Furyoku taiyoko hybrid hatsuden system ni kansuru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kimura, Y; Sakuma, H; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1996-10-27

In order to verify the complementary relationship between wind and solar energy, the long-term field test of the hybrid power system was conducted at the natural energy square of Ashikaga Institute of Technology. The solar cell blade windmill composed of a Savonius windmill and flexible solar cells applied to swept buckets was also prepared. As a result, the wind power generation was promising mainly in the winter period including the late fall and early spring, while solar one was stable all the year through although it was slightly poor in winter. Stable power generation was thus achieved by combining wind energy with solar energy. As the whole data of other wind and solar power generation systems at the square were analyzed for every month, the same conclusion as the solar cell blade windmill was obtained as follows: the wind power generation in Ashikaga area is promising in Nov.-March from the field test result for 16 months, solar power generation is stable all the year through, the hybrid power system is effective in Nov.-April, and the solar cell blade windmill is equivalent to the hybrid power system. 3 refs., 5 figs.

Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

Study on visibility evaluation model which is considered field factors; Field factor wo koryoshita shininsei hyoka model ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakanishi, M; Hagiwara, T [Hokkaido University, Sapporo (Japan)

1997-10-01

The present study proposes a model to evaluate visual performance of road traffic facilities required for drivers. Two factors were employed to obtain the suitable contrast for drivers under driving situation. One factor is a suitable luminance range, which is derived from minimum required luminance and glare luminance. Another is a field. The model showed capability of providing visibility range in some cases. 8 refs., 4 figs., 2 tabs.

Ultimate strength analysis of long-span cable-stayed bridges; Chodai chachokyo no shukyoku kyodo kaiseki to kyodo ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Xie, X.; Yamaguchi, H. [Saitama Univ., Urawa (Japan)] Nagai, M. [Nagaoka Technical Coll., Niigata (Japan)

1998-07-21

Recently, span of cable-stayed bridges has been getting loner and longer, present situation is that cable-stayed bridges with span 600 to 800m class have been built inside and outside the country, and accurate determination of its ultimate strength has been an important problem statistically. However, concrete design method for evaluating load bearing stress of long-span cable-stayed bridge. Particularly of the main beam whose axial stress is dominating, has not been established so far. As for cable-stayed bridge, even for long-span, effect of plasticization of cross section on ultimate strength is severe because there is little effect of geometric nonlinearity and it is thought that accurate evaluation of ultimate strength only by elastic finite potential analysis is difficult. Accordingly, it is necessary to study the behavior by using combined nonlinear analysis considering the nonlinearity of the material in order to evaluate the safety and economy to long-span cable-stayed bridge. In this report, 3 dimensional analysis method was formularized taking into account the combine nonlinearity of multi-box girder and analysis program of ultimate strength behavior of long-span cable-stayed bridge was developed. 19 refs., 17 figs., 2 tabs.

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on automobile engine); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-10

The paper made an investigational study of the data of a wide range which seems to be related to the use of hydrogen as automobile use fuel. The advantage is that the exhaust can almost be non-pollutant. The engine performance can be on the same level as that of the present gasoline engine or can be improved. The reasons are that the compression rate is heightened and that automobile can be driven at lean mixture rate. As to weak points, the volume and weight increase when it is loaded on vehicle. The cost of hydrogen is higher than that of petroleum. The problems to be quickly solved are as follows. Improvement of the combustion method: a wide range of development not only the electric ignition method, but the diesel method, and the basic study for it. It is necessary to establish the basis for a method to connect the storage method and engine. It is also necessary to comprehensively review rules related to safety. For the future, the conversion to artificial fuel is indispensable, and hydrogen has the most characteristics as energy medium. The problem is much larger sizes of fuel tank and pump, but there will be a possibility of producing a new technology together with the hydrogen production technology. The fundamental research should be promoted without any hesitation. (translated by NEDO)

Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

Study on internal flow near the impeller outlet of a winnowing fan. 2nd Report. Discussion of a impeller with forward-inclined blades by computational fluid dynamics; Karami fan no haneguruma deguchibu kinbo no nagare ni kansuru kenkyu. 2. CFD wo mochiita maemuki hane ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Kawase, M. [Tokushima University, Tokushima (Japan); Fukutomi, J.; Nakase, Y. [Tokushima University, Tokushima (Japan). Faculty of Engineering

2000-03-25

Because of a strong 3-dimensional flow, it is difficult to produce a uniform flow or improve efficiency with winnowing fans. Through experiments with various types of impellers, it was found in an earlier study that a forward-inclined impeller could produce a uniform flow and improve efficiency. It was ten reported in a subsequent study aimed at identifying the mechanism behind this, in which the relationship between velocity and static pressure in an impeller of small inclination angle was examined from the perspective of flow, that flow analysis was effective towards estimating inconsistent flow characteristics. Based on these findings, this project was designed to measure and analyze flow characteristics in a forward-inclined impeller. It was found that forward-inclined impellers have many regions of circulating flow and that the mainstream which moves to the outlet is narrow in effective area. As a result, velocity increases and discharge blow rapidly expands within a short distance. Therefore, good static pressure recovery is obtained. (author)

3Wave propagation in rock samples under medium and low temperature conditions. Characteristics of methane hydrate-BSR phenomena; Chu teion ryoiki ni okeru ganseki shiryo no hado denpa tokusei. 1. Methane hydrate BSR gensho no kosatsu suitei

Energy Technology Data Exchange (ETDEWEB)

Rokugawa, S; Kato, Y; Matsushima, J; Sano, A [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1997-10-22

In relation to sea-bottom pseudo reflection face and methane hydrate in seismic exploration records, fundamental experimental studies have been made. In order to get a handhold to elucidate phenomena accompanying methane hydrate, the studies have investigated wave propagation behavior of rock samples and sandy sediments under medium and low temperature conditions. The experiments have used a constant-temperature cooling water circulating equipment to control temperatures of each sample. The samples were placed in a cooler box with the vibration transmitter and receiver fixedly installed, and changes of the waves against temperature change were measured. Sand-stones and two kinds of tuffs were used as rock samples for the measurement. Artificial sand sample soaked in water was used as a substitute for a methane hydrate layer. As a result of the experiments, the relation between the hydrate layer and the gas layer was comprehended. In addition, the blanking phenomenon was thought occurring as a result of the nearly whole substance presenting the speed of ice due to freezing of the sediments, rather than by what is described in the ground homogeneousness theory. 5 refs., 9 figs.

Thermal boundary condition effects on forced convection heat transfer. Application of a numerical solution of an adjoint problem; Kyosei tairyu netsudentatsu mondai ni okeru netsuteki kyokai joken no eikyo. Zuihan mondai no suchi kai wo mochiita kosatsu

Energy Technology Data Exchange (ETDEWEB)

Momose, K.; Saso, K.; Kimoto, H. [Osaka University, Osaka (Japan). Faculty of Engineering Science

1997-11-25

We propose a numerical solution for the adjoint operator of a forced convection heat transfer problem to evaluate mean heat transfer characteristics under arbitrary thermal conditions. Using the numerical solutions of the adjoint problems under Dirichlet and Neumann conditions, both of which can be computed using a conventional CFD code, the influence function of the local surface temperature on the total heat transfer and that of the local surface heat flux on the mean surface temperature are obtained. As a result, the total heat fluxes for arbitrary surface temperature distributions and the mean surface temperatures for arbitrary surface heat flux distributions can be calculated using these influence functions. The influence functions for a circular cylinder and for an in-line square rod array are presented. 14 refs., 9 figs., 1 tab.

Effect of ventilated structure on dehumidification. ; Experimental result in winter. Tsuki koho no haishitsu koka ni kansuru kenkyu. ; Toki jikken kekka

Energy Technology Data Exchange (ETDEWEB)

Sugai, T; Ozaki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering; Katayama, T; Hayashi, T; Shiotsuki, Y [Kyushu University, Fukuoka (Japan)

1912-09-01

Temperature and humidity characteristics and condensation within walls under heating and humidification were studied experimentally in winter using two test houses of conventional and ventilated structures. The absolute humidity in conventional one fluctuated depending on temperature gradient, water flux due to humidification and water adsorption onto glass wool, and accumulated water increased with humidification. That in ventilated one was also affected by dehumidification through ventilation layers. Under heating and humidification, the absolute humidity increased depending on temperature rise and water flux within walls. In conventional one, condensation was frequently observed on felt in walls and others because of accumulated humidity, while in ventilated one, humidity was kept lower within walls even under heating, because humidity in walls was discharged through ventilation layers. Condensation was also scarcely observed on waterproof moisture-permeable sheets in walls and others. 3 refs ., 39 figs 1., tab.

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-10-01

For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

Study on hydrogen storage alloy for NiMH EV battery; EV yo NiMH denchi no suiso kyuzogokin ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kanemoto, M.; Tanaka, T.; Furukawa, K.; Watada, M.; Oshitani, M. [Yuasa Corp., Osaka (Japan)

1998-10-30

We have developed a high performance hydrogen storage alloy (MH alloy) suited to NiMH batteries for EV use. During the course of the development, the effects of alloy composition and structure (B/A ratio in AB{sub 5}) on cycle life and high-rate discharge of MH electrodes were investigated using mainly SEM, XRD, TEM analysis. It was found that Co content and B/A ratio (5.1/5) of MH alloy have significant effects on corrosion resistance and high-rate discharge at low temperature. Further, the surface treatments of MH alloy with weak acids and hydrophobic agents were effective for improving the initial activation and for depressing the cell internal pressure build-up. (author)

Investigational research on CO2 isolation technology in fiscal 1995; 1995 nendo nisanka tanso no kakuri gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper studied present technical subjects and future study subjects of the CO2 isolation technology in order to clarify technical and social problems and the developmental subjects of the CO2 isolation technology and related technologies for separating/concentrating CO2 emitted in relation to quantity consumption of fossil fuel and storing it in ocean or underground. Main items for the study were: (1) investigational study of the technology of CO2 ocean storage, (2) investigational study of environmental effect assessment in storing CO2 in ocean, (3) investigational study of the technology of CO2 ocean storage, etc. Technologies required for the ocean isolation were arranged such as CO2 storage, injection, dispersion technique, CO2 behavior simulation, and the developmental subjects were extracted. Further, in the deep-sea bottom storage method, a simulation to calculate the range of PH effects was conducted presuming the specified amount of CO2 and applying known physical values, and evaluation of the CO2 ocean discharge/solution method was made. A method was also studied for experiments on water bacteria and benthos. 127 refs., 102 figs., 81 tabs.

Studies on reducing the thermal loads of solar-pumped solid state lasers; Taiyoko reiki laser no netsufuka teigen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shimizu, K; Yugami, H; Naito, H; Arashi, H [Tohoku University, Sendai (Japan)

1997-11-25

It was intended to reduce the thermal loads of solar-pumped solid state lasers (highly densified solar light is irradiated directly onto a laser medium to cause excitation. No electric power is required for the excitation.). For this purpose, experiments were performed by using a selective permeation film. Solar light includes wavelengths not effective for excitation, which causes heat generation and thermal loads such as lens heating effect and thermal stress compounded refraction, degrading the laser beam quality. The Nd:YAG was used as a laser medium, and a multi-layered film (composed of SiO2 and TiO2) which cuts wavelength below 500 nm as a selective permeation film to cut light having wavelengths not required for excitation. A laser transmitting experiment revealed that the slope efficiency is improved by 27% as compared to not using the film. Beam fluctuation was improved to 45%. Using the selective permeation film has realized more efficient conversion of the solar light into a beam with better quality. The results for calculation of heat lens effect by using temperature distribution simulation showed good agreement with experimental values. Using the selective permeation film can suppress the maximum temperature of a laser rod to 68%, as well as the thermal stress. 9 figs., 2 tabs.

Improved design of three-dimensional lens for low concentrator PV modules; Teishukogata taiyo denchiyo sanjigen lens no koseinoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Goma, S; Yoshioka, K; Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan)

1997-11-25

Attention is paid to reduction in area required for solar cells by solar concentration as a means of solving cost limits of solar cells and unstable supply of Si materials. Low concentration solar cells are effective from the aspects of utilization of scattered light and unnecessary ray tracing. The optical concentration ratio was calculated of three-dimensional lens having design values of various north/south and east/west direction allowable incidence half angles. The three-dimensional lens are designed by cutting a rectangular parallelepiped by the two-dimensional composite elliptical plane designed by various allowable incidence half angles from two directions of north/south and east/west. Using Perez`s sky solar radiation models and meteorological data HASP, calculated were the annual accumulated global radiation ratio on an inclined surface and the optical efficiency. Calculated were the solar cell area ratio and solar concentration area ratio of the concentration type to obtain solar radiation the same as that of the planar type. From the optimization calculation, it was found that lens are optimal which have design values of north/south and east/west direction allowable incidence half angles of 30-70deg. The solar cell area ratio is 57% and the solar concentration area ratio is 1.2 times. It was found that by making the module area 1.2 times, more than 40% of the solar cells used can be saved. 5 refs., 8 figs.

Study on recent research trends in the chemical fields; Kagaku bun`ya ni okeru saikin no kenkyu doko ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This research is conducted to search study themes of chemistry expected towards the 21st century. The complex compound in the fundamental chemistry field and the bio-medical materials in the applied chemistry field are taken up. Bio-medical materials are used for the restoration, rehabilitation, and treatment of the organ and the improvement of its functions. For implants such as hearts, anti-thrombin and anti-calcium precipitation effects and high endurance are required. In this field, special copolymers and bio-membrane-emulating surfaces are studied. For artificial organs, hybrid type materials combining cells, and physiologically active and artificial materials are also studied. There are studies on the missile therapy of drugs and DDS (drug delivery system). The complex compounds contain metallic elements, such as Fe, Mn, Co and Cu, and groups known as ligands which combine these metal elements. They can have a variety of stereo-structures and physical properties. They also exhibit a diversity of functions including electron donor bonding, molecular recognition, chemical substitution, and pharmaceutical activity. These features open up a promising potential for their prospective use as physiologically active substances, cancerostats, new materials, artificial photosynthesis, memory elements, and complex catalysts. 88 refs., 35 figs., 6 tabs.

Investigational study of optical function materials for two-dimensional data processing; Nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper investigated/studied `space light modulation materials,` `dynamic hologram/memory materials,` `optical waveguide path materials,` etc. which become key materials in the high speed two dimensional processing. As to electrooptical materials proposed in this investigational study, the external electric field and the electric charges generated make quality of molecules themselves directly change to memory strong/weak signals of light. Therefore, the response velocity becomes less than a millionth of that of the liquid crystal display, and high speed which is needed for realtime moving image processing is anticipated. Hologram includes the phase information in addition to information on light strength. Therefore, it is a large capacity record medium and at the same time a record medium which can read/write two dimensional information as it is. With optical fiber, images cannot be transmitted as they are. Light waveguide path materials are those that accumulate roles of mirror and lens in a sheet of the material and construct a system which is strong in vibration, as optical parts connecting among materials for two dimensional data processing. 273 refs., 107 figs., 17 tabs.

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-05-01

The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

Trend of research on future development of new biocatalysts. 2; Shinki bio shokubai no sosei ni kansuru kenkyu doko chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Creation of new biocatalysts was surveyed to convert chemical reactions into environment-friendly processes. Biocatalysts are characterized by their high catalytic activity, uniqueness of reactions, and non-pollution under mild conditions. Stability is required for them, such as heat resistance, solvent resistance, acid resistance and alkali resistance, under severe conditions. For the development of new biocatalysts, it is necessary to multiply utilize the techniques containing enzymes, ribozymes, mold synthetic polymers, chemical modification, and non-natural proteins. Natural enzymes have been conventionally improved through the search, imitation and modification. Hereafter, new biocatalysts with functions required for the reactions should be created by integrating information regarding functions, structures and activation of these enzymes. It is indispensable to cooperate closely with supporting techniques, such as gene engineering, organic synthesis, biophysics and computer chemistry. 35 refs., 26 figs., 1 tab.

Study on the impact assessment for the life cycle assessment (LCA); Kankyo fuka bunseki ni okeru impact assessment ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes the impact assessment which is an important step for LCA. For classification of the impact assessment, the existing literature was reviewed and a skeleton for the classification was proposed. The weighting factors for nine selected impact categories, which were used to calculate environmental load point (ELP) for the valuation, were obtained for two overseas groups, i.e., students of Amsterdam University and SETAC Europe members. It was found that the former provided the similar trends to general Japanese, however that the latter gave high weighting in the global warming and depletion of ozone layer. The ELP was proposed and applied to automatic washing machine, coffee maker, waste incineration power generation system, and co-generation system. As a result, its effectiveness was demonstrated. This report also describes problems for the LCA of thermal and material recycling of PS trays. 99 refs., 96 figs., 73 tabs.

Survey on a possibility of geothermal utilization in Tomakomai City; 1980 nendo Tomakomaishi ni okeru chinetsu riyo kanosei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-11-01

This paper describes a possibility of geothermal utilization in Tomakomai City. The Tomakomai area has an extremely great amount of hot water existing in deep layers, leading to a consideration that it is very highly possible to develop the hot water. As seen from the underground structure and ground temperature gradient in the Tomakomai sedimentary basin, the development depth would be considerably great, being assumed to be about 2,000 meters. The acquisition amount per well is estimated 100 m{sup 3}/hour or more at 65 degrees C. Rise in petroleum price in the future is an unavoidable fate, hence geothermal water utilization has a fully bright future. The water has relatively low temperature, and is effective for use in room heating, hot water supply, and agricultural and livestock industries. It is worth considering utilization as a local energy system. It has also large secondary effects. According to the latest trial calculation, the unit price for hot water for room heating and hot water supply would be 10 to 20 yen per 1,000 kilo-calories. If the same amount of hot water should be supplied from a boiler, fossil fuel of 20,470 kl/year would be required. If converted by using a kerosene price of 75 yen per liter, the cost would be 1.3 billion 35 million yen, comparatively higher than the geothermal water utilization. (NEDO)

Research cooperation project on conservation and sustainable use of tropical bioresources; Seibutsu tayosei hozen to jizokuteki riyonado ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research cooperation has been conducted on the conservation of biological species inhabiting in the tropical rainforest in developing countries in tropic zone and the sustainable use of genetic resources using biotechnologies. For the research cooperation with Thailand in FY 1996, research of the food acquisition strategy of the Primates has been conducted. A total of 19 species of animals and plants, i.e., 7 species of arbors, 7 species of herbs, and 5 species of insects, were newly confirmed for pig-tailed monkey. In Indonesia, a feasibility study was conducted on the information center of Indonesian tropical bioresources. For the research of culture collection of bacteria, 113 strains of acetic acid bacteria and 85 strains of lactic acid bacteria were separated from Indonesian specimens, and they were identified. An agreement was concluded with Malaysia, and discussions were conducted for the concrete implementation plan. For the project, construction of a database was investigated for bioresources including bacteria and higher animals useful for industries. Maintenance of gene bank was also investigated. 391 refs., 61 figs., 93 tabs.

Report on investigations and studies on chemical conversion of photo-energy; Hikari energy no kagakuteki henkan ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper summarizes problems in utilization of solar energy, their solutions, features, the currently achieved results, and prospects. With regard to water decomposition using semiconductors, simultaneous generation of hydrogen and oxygen has already been achieved, and there is high possibility of raising the efficiency by improving catalysts. Water decomposition using metal complexes has acceleration of charge isolation as the largest problem, whose prospect of solution is not necessarily bright at the present time. Photo-catalytic reaction is a field to be discussed as one means of developing a new synthesizing method from the viewpoint of organic synthetic chemistry. Conversion into electric energy that uses a photovoltaic process has high efficiency, and is a field to be noted. In photo-energy conversion by means of photo-synthesis, living organisms performing hydrogen production at high efficiency have been discovered. Important studies include the studies in terms of chemical engineering using these living organisms, improvement of breeds by gene manipulations, and studies that utilize living organisms or part of the constituting components. (NEDO)

Study on the estimation method of maneuvering hydrodynamic force in turning motion; Senkai undoji no soju ryutairyoku suiteiho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kijima, K; Yukawa, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Maekawa, K [Hokkaido University, Sapporo (Japan). Faculty of Fisheries

1996-04-10

Estimation of the maneuvering performance of ships is very important from the viewpoint of safe navigation. Using three types of VLCCs (SR221A, B, C) with locally different stern frame lines as computational models, the estimation method of hull hydrodynamic force in turning motion was studied theoretically taking frame line shapes into account. The unstable behavior of courses was also studied using linear differential coefficients obtained from the estimation result on hull hydrodynamic force in oblique navigation and turning motion. As a result, the estimation result on hull hydrodynamic force was slightly different quantitatively from model test results in a range of large drift angle or turning angular velocity, while that was relatively well agreed with test results in a range of small such angle and velocity. As the study result on the unstable behavior of courses by using linear differential coefficients obtained from the estimation result on hull hydrodynamic force, determination of a course stability was possible by considering local difference in hull shape. 4 refs., 8 figs., 1 tab.

Survey on weather changes associated with large-scale tree-planting. 2; Daikibo ryokuka ni tomonau kiko henka ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

An investigational study was made for large-scale tree-planting aiming at CO2 fixation. Water resource and precipitation relating to tree-planting were determined from NASA data and arranged into the global distribution map. It was found that Australia and the Chinese continent are under the relatively favorable condition. As for the soil condition, nutrition resource is short in the desert and unused zone. From the vegetation data obtained from meteorological satellite NOAA, developed was a method for estimating net primary productivity of terrestrial ecosystem and obtained was a global distribution map for the amount of CO2 fixed under the present terrestrial vegetation. At the same time, areas which have great potentiality of tree-planting were selected from the map for estimating potentiality of the global tree-planting. To study the promotion of rainfall as a means of expanding the potential tree-planting area, the conventional meteorological and physical model was improved, and more realistic simulation was made possible. Also as to the water utilization technology, the modeling method was developed. As the area having a potentiality of expanding tree-planting, Australia (especially the west) was cited as the first candidate, and China the second candidate. 108 refs., 128 figs., 49 tabs.

Study on a technology to afforest water level varying part of a reservoir; Chosuichi suii hendobu ryokuka gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onodera, O.; Matsubara, K.; Koyama, S. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1999-03-19

Equisetum was noted as a plant adaptable to stringent environment referred to as the water level varying part of a reservoir, and was used for afforestation trials. The afforestation trials were performed at the reservoir of Uryuu Dam No. 1 and the regulating reservoir of Moiwa Dam of Hokkaido Electric Power Company. Although the rate of water level variation is small at Uryuu Dam No. 1, it is necessary for Equisetum to withstand submergence and drought for an extended period of time. Moiwa Dam has high water level variation rate, but its water depth is small, and the reservoir is free of long-term submergence and drought. As a result of long-term observation from 1993 through 1997, Equisetum was found having grown well at lower altitude part with higher submergence frequency. It has grown favorably even in parts where submergence rate reaches about 80%. However, at higher altitude with submergence rate of 10% or lower, decrement trend was seen. At Moiwa Dam, Equisetum was all buried in accumulated sand and earth, revealing that such an environment is unsuitable for Equisetum as the one subject to effect of sand and earth that flow in during freshet. (NEDO)

Research cooperation of the development of laser radar for environmental measurements; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research and development of the laser radar for measuring the air pollution in urban areas and the environmental information network have been conducted through the cooperation with Indonesian researchers. A measurement system suitable to actual situation of Indonesia has been constructed. In FY 1996, some works have been conducted as in the final fiscal year. To set the laser radar for environmental measurements and to make a plan of measurement research, conditions of air pollution in Indonesia and setting places of systems have been investigated. Opinions for the cooperation research have been exchanged with Indonesian researchers. Actual trends of the environmental measurements technology using laser radar have been surveyed. Indonesian researchers have been invited to learn operation and data processing of the system. One unit of MIE diffusion laser radar system has been designed and fabricated, and an additional data processing program has been made. The system has been delivered to Jakarta and installed. After the adjustment, performance tests have been conducted to complete the construction of the system. 3 refs., 72 figs., 10 tabs.

Research on giving antibacteria activity of tailored dental materials; Gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The secondary dental caries easily occur by breeding of bacteria in cavities between living body and composite resin, false tooth or root of tailored tooth as tooth repairing materials. The antibacteria activity of tailored dental materials was thus studied by implanting Ag ion. The antibacteria effect with time after culture of caries bacteria was studied by implanting Ag ion into SiO2 powder, PMMA samples and Ti alloy samples at 20 and 200keV in energy of ion. In addition, the antibacteria activity of SiO2 powder as composite material was found at 25keV which was previously effective for the antibacteria activity. This SiO2 filler (Ag{sup +} filler) showed the antibacteria activity on every bacteria sample after 2h, and in particular, could kill all of 3 kinds of bacteria obtained from a composite resin surface after 12h. The number of living S. salivarius was reduced by half after 12h. The application of the composite resin filler implanted with Ag{sup +} is significant to prevent recurrence of caries. 5 refs., 27 figs., 7 tabs.

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for aircraft engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Koku engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-01

With an objective to utilize hydrogen fuel in aircraft engines, a conceptual design survey was carried out on medium size transport aircraft. Large size long-distance aircraft and SST loaded with a great amount of fuel have the jet fuel (JP) increase take-off weight, affecting largely the selection of wing area and engine thrust. If the hydrogen fuel can be liquefied, large reduction can be achieved and the economic effect can be increased. However, for short-distance transport aircraft, the fuel weight ratio is small, where no large advantage is anticipated even if hydrogen is liquefied. Nevertheless, considering oil depletion in the future, a conceptual design was performed on the YX2688 short-medium distance aircraft being discussed of development. Even the short-medium distance aircraft that can be developed and commercialized as civilian use aircraft has a number of common points with large aircraft development, such as hydrogen fuel using technologies and safety. Although the advantage of using liquefied hydrogen as fuel may of course be smaller in the short-medium distance aircraft than in larger aircraft, the trend of using hydrogen fuel is historical necessity, whose development plans should be moved forward. (NEDO)

Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education - iron and steel (Survey on education accreditation in material field); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (tekko) -Zairyo bunya ni okeru kyoiku nintei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, a survey was performed on external accreditation systems for engineer education such as in universities and other organizations in the material field. In the survey, discussions were given on whether or not the education program accreditation system for the material field being structured has any problem in the actual operation of the accreditation through trials at Chiba Engineering University and Tokai University. As a result, it was revealed that the criteria are too general, requiring more detailed description on the guideline, and criteria should be so considered that assessment at higher levels can be given to the graduation research, which is a Japan's particular education system. In addition, it was made clear as a problem in the education programming side that a room for improvement remains in the education methods for the engineering ethics, communication skills, and the method for evaluating the students' achievements. In the survey on the methods for examination and accreditation in the U.S.A. it was found out that education organizations are perplexed with the new criteria of EC 2000. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for chemical utilization); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-04-15

Surveys and studies were performed on chemical utilization of hydrogen regarding its status of development and utilization inside and outside the country, as well as its future prospect. This paper describes chemical utilization of hydrogen in ammonia, methanol, petroleum refining and other industries as the existing fields. It also describes chemical utilization of oxygen in iron and steel, chemical and other industries. It describes methanol as a pollution-free auxiliary fuel for electric power plants as a new type of hydrogen application. Acetic acid made by using the Monsanto method which carbonylate methanol is drawing attention in terms of economy, and is in the phase of discussing commercialization. Synthesizing ethylene glycol from carbon monoxide and hydrogen may be conceived economically. Methanol for synthesized protein depends on the possibility of future development. In the iron and steel industry, electric furnace steel makers are planning production of reduced iron, where the direct reduction process using hydrogen is considered as a complementary process, including countermeasures for scrap iron. This paper estimates hydrogen amount as a raw material for ammonia to remove NOx by using the ammonia reduction process. It also describes possibility of other types of utilization. (NEDO)

Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the chemical utilization); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-07-01

This paper reports on the present situation of the chemical use of hydrogen and oxygen, and the short-term, medium-term, and long-term forecast. The main usage of hydrogen is ammonia synthesis, petroleum refining, and methanol synthesis. In the usage of these three, there are factors of structural changes now and in future, and it is extremely difficult to predict the amount in a short term up to around 1980. In a medium term prediction, from the result of predicting the demand of ammonia, methanol and hydrodesulfurization, the total 1985 hydrogen demand is estimated at approximately 60 billion Nm{sup 3}, and approximately 67 billion Nm{sup 3} as the gross hydrogen demand. Further, judging from that synthetic protein, fuel use methanol, and reduced iron are estimated to reach a certain production size in and after 1985, new demand for hydrogen is expected to be approximately 100 billion Nm{sup 3} mostly including fuel use methanol. In a long term prediction, it is extremely hard to predict the demand because of various factors existing in Japan and abroad. As predicted in a medium term, the amount of chemical use of hydrogen is expected to increase more and more, even if calculating it only in the field of ammonia synthesis, petroleum refining, and methanol synthesis. (NEDO)

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y [Hiroshima University, Hiroshima (Japan); Okusu, M [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1997-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Survey on the feasibility of high-efficiency gas turbine power generation system; Kokoritsu gas turbine hatsuden system ni kansuru jitsuyo kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For higher-efficiency power generation cycle plants with less restrained conditions for a location, the conceptual design of an inter-cooled regenerative two-fluid cycle plant (ISTIG) was attempted using a modified aircraft gas turbine. A high-performance turbo fan engine is used for middle-class power generation. The first stage combustion gas drives the first stage turbine, and its exhaust gas is used for the second stage combustion. Because of two-axial type of high and low pressure, improvement of thermal efficiency is expected by easy-to-install inter-cooler. ISTIG superior in operability is suitable for medium load or distributed power generation facilities, and aims at higher efficiency of a 60% level. ISTIG includes a large amount of water vapor in combustion air by adopting a diffusion type combustor eliminating back fire, and can reduce exergy loss by preheating fuel gas. Since load of the high-pressure turbine shifts toward low-pressure one by the inter-cooler, some considerations are necessary for low-pressure side cooling together with reheating cycle. Because of unnecessary steam turbine, the construction cost per kW can be reduced by 20%. 41 refs., 64 figs., 27 tabs.

International symposium on environmental impacts of advanced alternative to CFC; CFC shinki daitai busshitsu no kankyo eikyo ni kansuru kokusai symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-07

The international symposium on environmental effects of new CFC substitutes was held in Tsukuba City, Ibaraki Pref. on February 7-9, 1996, and 19 papers were made public. In Session 1 (Plenary lecture), reports were made on Global warming and climate change: a review of recent studies; Stratospheric ozone, CFCs, and CFC-substitutes: an update, etc. In Session 2, Measurements of OH rate constants for advanced refrigerants as well as HCFCs and HFCs; The reaction rate of CFC alternatives with OH radical; Experimental and estimated rate constants: reactions of hydroxyl radicals with several halocarbons, etc. In Session 3, Measurement of uptake coefficients of some acetyl halides and fluorinated ethers into water; Mass transfer at the air/water interface: removal processes of halocarbonyl compounds; Heterogeneous reactions of fluorinated ethers on allophane or titanium dioxide, etc. In Session 4, papers were reported on model calculations relating to the global warming.

Required grades of hull steel plates in consideration of fracture toughness; Hakai jinsei wo koryoshita sentaiyo koban shiyo kubun ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Yajima, H; Yamamoto, M; Ogaki, Y [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1997-10-01

This paper discusses the required grades of hull steel plates based on the steel ship rule of Nippon Kaiji Kyokai (NK). The minimum value of the allowable crack length in NK rule (critical safety crack length at 0degC just before brittle unstable crack causing fatal fracture) was estimated. In the case where the estimated crack tip exists in a matrix, the crack length was a minimum of 200-210mm, while nearly 60mm in a fusion line at high-heat-input welded joint. The allowable crack lengths estimated from a specified value in the NK rule were fairly different. The allowable crack length at 0degC was also estimated from the minimum value in V-notch Charpy impact test. The private proposal on the required grades of hull steel plates in consideration of fracture toughness was discussed. Thirty-five percent of crack lengths found in real ships is 100mm or less, however, cracks of 250-400mm long are frequently found suggesting the allowable crack length of 400mm. The required grade integrally considering required values and design conditions is demanded to secure the reliability of hull strength. 5 refs., 5 figs., 2 tabs.

Survey report on an environmental harmony type production system of chemical products; Kankyo chowagata kagaku seihin seizo system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

As part of establishing an environmental harmony type production system of chemical products, study and survey were made on PET bottles. Using the life cycle analysis method (LCA), a study was made for proposing a material recycle (MR) method which is environmentally and economically excellent in the stage of recycling waste PET bottles. The total cost of recycling can be reduced by 34% supported by a decrease in equipment cost and improvement in yield if there is no mixture of foreign substances such as aluminum caps and PVC bottles. However, the ratio of the amount obtained from the reduction to the total production cost is small, and it is necessary to take measures from a viewpoint of the cost in a total production process and environmental loads. In a survey in Kawaguchi city, PET bottles discharged from the business sector occupied 41% of all the discharge amount. In a survey in Yokohama city, very important data were obtained on PET bottles appointed as the second type under the recycle law. The quality of PET bottles to be brought to the recycling plant is important for effectively processing PET bottles in MR method. For achievement of MR which is low in cost and small in environmental load, needed were cooperation by citizens, the shipping management system in autonomous government, and changes in design and material quality to be made by the industrial circle. 8 refs., 64 figs., 68 tabs.

Basic studies on application of vegetable factory in Tohoku region; Tohoku chiho ni okeru yasai kojo no jitsuyoka ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Okano, T; Terazoe, H; Shoji, K; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan); Tanaka, M; Miura, K [Tohoku Electric Power Co. Inc., Sendai (Japan)

1995-08-01

To construct vegetable factories in the Touhoku region, items of information have been collected with respect to items to be cultured and market conditions. Experimental discussions have also been given on new culture items and methods for utilizing snow. Using the results of investigations on the market conditions and weather environments, the following three kinds of spicy vegetables were selected: water cress which grows in about 46 culture days after seeding and in about 36 days by herbaceous cutting to a harvest of about 700 g/m{sup 2}, green perilla which grows in about 85 culture days to a number of salable leaves of 100 per stock, with an average leaf area of about 55 cm{sup 2}, and trefoil which grows in about 56 culture days to a harvest of about 5100 g/m{sup 2}. According to a storage experiment using snow, lettuce packed with snow in a box retained at a temperature of 5{degree}C and a humidity of 100%, pre-cooled for one day and then stored for six days in a refrigerator at 5{degree}C presented very little decrease in fresh weight and no decrease in freshness. The same result was obtained also for the Sunny Lettuce. 9 refs., 19 figs., 9 tabs.

Estimated method of permeability in the granitic rocks by geophysical loggings; Butsuri kenso shuho ni yoru kakoganchu no tosuisei ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Matsuoka, K; Hashimoto, N. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)]Ogata, N. [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

1997-10-22

Water permeability in granite is estimated by performing geophysical investigation using a 500m-deep test hole drilled in granitic rocks in the vicinity of a Tono mine. The investigation consists of flowmeter logging and geophysical logging. In flowmeter logging, a probe is moved up and down in the hole at a constant speed by use of a cable, and the cable speed and impeller revolution are used to workout the relative speed of the fluid in the hole. In the geophysical logging, a probe attached to the leading end of a logging cable is replaced with other probes so as to acquire different geophysical data. In a hole drilled in a crack-abundant rockbed such as a granitic rockbed, the inflow and outflow of ground water is governed mainly by water-permeable crack zones, and the result of the flowmeter logging show that this hole has three highly water-permeable zones. Using the results of the loggings, a correlative equation is worked out between changes in flow speed and changes in permeability index obtained by hydraulics tests. Among the various results achieved by the geophysical logging, a fine correlationship is found between an equation relative to permeability obtained using electricity and density and water-permeability indexes obtained by hydraulic tests conducted in situ. 4 refs., 8 figs., 1 tab.

Investigation on behavior of bacteria in reservoir for microbial enhanced oil recovery; Biseibutsuho (MEOR) no tameno yusonai saikin katsudo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, K.; Tanaka, S.; Otsuka, M.; Nakaya, K. [Kansai Research Institute, Kyoto (Japan). Lifescience Research Center; Maezumi, S.; Yazawa, N. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Hong, C.; Chida, T.; Enomoto, H. [Tohoku University, Miyagi (Japan). Graduate School of Engineering

2000-07-01

Behavior of bacteria activated in reservoir though molasses-injection-tests, was investigated using the restriction fragment length polymorphism analysis with the polymerase chain reaction (PCR-RFLP) method, for elucidating potential bacteria to suppress in situ growth of microbes to be injected into the reservoir in the microbial enhanced oil recovery (MEOR) process. As a result, some bacteria belonging to Enterobacteriaceae species or their close relative species were grown predominantly in the reservoir, among bacteria inhibiting in the ground-water. The foregoing indicates that behavior of these bacteria in reservoir must be taken into consideration when giving a full account of behavior of microbes to be injected into the reservoir to put the MEOR process into operation. Potential proliferation using molasses to activate those bacteria was also estimated on the laboratory tests, to clarify the growth of microbes to be injected into the reservoir to operate the MEOR process. In consequence, it became clear that these bacteria have a potential growth exceeding 10{sup 8} CFU/ml, utilizing molasses. These facts indicated that microbes to be injected into the reservoir at the MEOR field tests are necessary to grow more excellently than bacteria inhabiting in the ground-water. In addition, as flow, the injection fluid is influenced by reservoir heterogeneity caused by injection of molasses, it was inferred that microbes to be injected into the reservoir at the MEOR field process are also necessary to grow more remarkably than bacteria inhabiting in the reservoir brine at high permeability zones and bacteria inhabiting in the reservoir rock. Furthermore, the results of the functional testing for MEOR conducted in the presence of bacteria activated through molasses-injection-tests indicated the importance of effective use of microbes to be injected, taking into account the characteristics of the reservoir and function for MEOR of those microbes. (author)

Evaluation for characteristics of around the Nojima fault; Butsuri tansa ni yoru `Nojima jishin danso` shuhen no jiban bussei ni kansuru ichihyoka

Energy Technology Data Exchange (ETDEWEB)

Shimizu, K; Tsuji, T [Newjec Inc., Osaka (Japan); Tsuji, M [OYO Corp., Tokyo (Japan)

1996-05-01

Various surveys were conducted for the area around the Nojima fault, including ground surface, two-dimensional electrical and boring surveys and elastic wave tomography, in order to grasp properties of the ground around the `Nojima earthquake fault.` The resistivity image method as one of the two-dimensional electrical methods was used to grasp fault shapes over a wide range of the 1.6km long section extending between Esaki and Hirabayashi. The courses of traverse were set in the direction almost perpendicular to the fault. Boreholes were excavated and elastic wave tomography was conducted between the boreholes on the 9th and 17th courses of traverse, to confirm ground/mountain conditions and to compare the results with observed elastic wave velocities. Very low resistivities are observed at places where granite is distributed, suggesting that the fault-induced changes are not limited to the area around the fault. The zone in which elastic wave velocity decreases is narrow, 10m at the longest, at a velocity of 2.4km/s or lower, which is a low velocity for that propagating in granite. 5 refs., 4 figs.

Research on improvement of indoor air quality and prevention of fungi; Shitsunai kuki kankyo no kaizen to kabi boshi ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Tatsuaki [Ochanomizu University, Tokyo (Japan). Faculty of Human Life and Environmental Sciences

1998-12-16

An epidemiological survey survey was performed to elucidate the fungal flora of a dwelling house. The measurements were carried out in an apartment in Yokohama from Jul. 1996 to Dec. 1997. Fungi were isolated from 106 sampling points (the surface of the walls, floors, etc.) with sterile stamps. It was proved that Cladsporium, Penicillium, Eurotium, and Yeasts showed characteristic distribution. Especially Cladsporium was not isolated from the spring to the summer, but increased in the autumn. In addition to the survey, experiments on fungal growth temperature (13, 20, 25, 30, 36, 42 degree C) and water activity (A w 0.75{approx}0.97) were carried out. Cladsporium grew well in 13, 20, 25 and 30 degree C, but didn't grow in 36 and 42 degree C. In addition, the growth activity of Cladsporium was down below Aw 0.91. Eurotium was isolated from under Tatami, where it has an unchanging temperature and relative humidity. Yeasts preferred very high humidity. It was concluded that environmental factors such as temperature and relative humidity related to the growth of fungi. (author)

Study of fuel spray characteristics for premixed lean diesel combustion; Kihaku yokongo diesel kikan ni okeru nenryo funmu keisei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

1998-05-01

A study is being made on premixed lean diesel combustion (PREDIC) by means of early fuel injection in diesel engines. The PREDIC makes it possible to largely reduce NOx emission, but has such problems as ignition control and increase in THC and CO generation. In order to clarify the relationship between fuel spray characteristics in the PREDIC and properties of gas mixture and exhausts, the present study has investigated spread and internal structure of the spray by means of spray observation experiment using a pintle swirl nozzle. Based on the result therefrom, simulations were used to investigate effects of spatial dispersion characteristics of the spray on properties of the gas mixture and exhausts before ignition. The pintle swirl nozzle forms conical spray having an air layer inside the spray, where penetration is suppressed even under low atmospheric pressure. By forming hollow spray or solid spray in the conical spray, a possibility was indicated that equivalent ratio distribution of the gas mixture can be controlled and NO emission may be reduced. 8 refs., 12 figs., 1 tab.

Fiscal 1999 research cooperation project report. Research cooperation on coal liquefaction technology; 1999 nendo sekitan ekika gijutsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research cooperation project result on coal liquefaction technology. Cooperative FS was made on coal liquefaction technology of Indonesian coal as petroleum substituting energy. To obtain the basic data necessary for the FS, study was made on the applicability of Indonesian natural minerals as catalytic materials. Promising low-cost abundant Soroako Limonite ore showed a high catalytic activity for liquefaction reaction of Banko coal, and an excellent grindability. Improved BCL process including hydrogenation process was promising for production of high-quality coal liquid superior in storage stability with less nitrogen and sulfur contents. Survey was made on the general conditions of Tanjung Enim area including South Banko coal field concerned, and the geological features and coal seam of South Banko coal field which is composed of 3 seams including coal deposits of 6.35 hundred million tons. To study the marketability of coal liquid, survey was made on the current situation of oil, oil product standards, and blendability of coal liquid. Hydrogen for the liquefaction process can be obtained by coal gasification. (NEDO)

Application of photovoltaic generating system to electric power in large ship; Taiyoko hatsuden system no ogata senpaku eno oyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Katagi, T; Ogawa, S; Nishikawa, E; Hashimoto, T [Kobe University of Mercantile Marine, Kobe (Japan); Ishida, K

1996-10-27

This paper describes the design of electric power system in a ship with photovoltaic power generating system, to examine applicability of the photovoltaic power generating system to the inboard power source. It also discusses effectiveness of the system for sea environment. At first, the actual route of a car carrier, meteorological data, and quantity of power consumption were picked up from the deck logbook and engine logbook. Then, the installation area of photovoltaic arrays, the quantity of photovoltaic power generation derived from the quantity of solar radiation, and the capacities of batteries and inverters were calculated, to design the electric power system in the ship with photovoltaic power generation system. Moreover, the NOx and SOx emissions were compared between the present power system and the usual power system using diesel power generator, to discuss the effectiveness of the present system for sea environment. Consequently, it was found that the emission of NOx was reduced by about 33% and the emission of SOx was reduced by about 28% compared to the usual power system. The effectiveness for sea environment was confirmed. 9 refs., 5 figs., 4 tabs.

Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Imai, Y. [Hiroshima University, Hiroshima (Japan); Okusu, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

1996-12-31

A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

Study on collapse behavior of a square plate subjected to water pressure; Suiatsu wo ukeru kukeiban no atsukai kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yao, T; Fujikubo, M; Mizutani, K [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1996-04-10

Bottom plates of a hull are subjected to laterally distributing force due to in-plane compression force and water pressure in the ship`s length direction as a result of longitudinal bending in a hogging condition. Because buckling collapse of the hull bottom plates leads directly to longitudinal bending collapse of the hull bottom cross section, the hull bottom plates must have sufficient strength. The present study performs a static elastic large deflection analysis and an elasto-plastic large deflection analysis. It elucidates buckling collapse behavior of a square plate subjected to water pressure and in-plane compression load, and considers limits in application of conventional approximation analysis methods. In the case of a water pressure action, deflection components growing in excess of the buckling load do not necessarily correspond to buckling modes of the case where no water pressure is acting upon. Conventional approximation analysis methods may not be able often to pursue actual buckling phenomena. According the result of an analysis on hull bottom panels of an actual ship, the ultimate strength decreases when the water pressure is large. Compression force in the lateral direction as a result of water pressure acting on ship`s sides affected very little the ultimate strength. 3 refs., 7 figs.

Consideration on longitudinal bending moment in waves of a large high-speed ship; Ogata kosokutei no haro tatemage moment ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Deguchi, M; Takimoto, T; Kasuda, T; Tozawa, S [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1996-04-10

While high-speed ships are on a trend of increased speed, size and diversity, one of the most important items is a discussion on large high-speed ships with a total length of 100 m class on their longitudinal strength in waves. With such a background, a model ship intended of realizing a large high-speed was assumed, and verification of reliability in structural strength and establishment of a design method for this ship were intended. Therefore, oceanographic condition setting, design load setting, FEM analysis, and strength assessment were carried out. This paper reports the results of comparison with and consideration on conventional criteria and linear calculations, mainly the results of simulated calculations on non-linear hull movement/wave load which have been performed in discussing the loads. The result of the non-linear simulation is thought to have well simulated non-linearity characteristic to the ship. Conventional criteria which have been arranged on the record of use for small ships are considered impossible to be applied to large high-speed ships. Under such a situation, the simplified equations by Kaneko et al are judged effective in making an initial plan for this type of ship. 6 refs., 7 figs., 2 tabs.

Research and development on a single-frequency simultaneous two-way cellular wireless device; Ichishuha doji sohoko ido musenki ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A cellular wireless device performs signal transmission and receiving using only one assigned frequency because of effective frequency utilization, and therefore, is inconvenient in actual use. For this reason, a cellular wireless device operating on a new principle was developed to make simultaneous two-way calls possible on one frequency. The operation principle is such that one frequency is used, voice signal is divided on the transmission side at every 0.4 second, compressed in time to 1/2, and transmitted in 0.2 second upon modulation; and the receiving side extends the signal to a double length upon demodulation to take out the original voice signal. Thus, the transmission time is reduced to half, and the remaining half time thus obtained is assigned to the receiving time from a caller in the similar method to perform a two-way simultaneous call. Both hands can be used freely during a call, making the safe call possible even while driving a vehicle or performing a work. High confidentiality can be maintained by means of voice processing, compression, and extension. Size of the device was reduced, reliability and clarity were optimized, and a large number of frequency can be switched easily. Field test have proved that the device meets the criteria specified in the Electric Wave Law. The device was begun of business use in 1992. It can be connected with portable type telephone sets and those used in business compounds. 2 figs.

Report on evaluation of research and development of superhigh-function electronic computers; Chokoseino denshi keisanki no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-02-20

Described herein is development of superhigh-function electronic computers.This project was implemented on a 6-year joint project, beginning in FY 1966, by the government, industrial and academic circles, with the objective to develop standard, large-size computers comparable with those of the world's highest functions by the beginning of the 70's. The computers developed by this project met almost all of the specifications of the world's representative, large-size commercial computers, partly surpassing the world's machine. In particular, integration of the virtual memory, buffer memory and multi-processor functions, which were considered to be the central technical features of the computers of the next generation, into one system was a Japan's unique concept, not seen in other countries. The other developments considered to have great ripple effects are seen in LSI's, and techniques for utilizing and mounting them and for improving their reliability. Development of magnetic discs is another notable result for the peripheral devices. Development of the input/output devices was started to correspond to inputting, outputting and reading Chinese characters, which are characteristics of Japan. The software developed has sufficient functions for common use and is considered to be the world's leading, large-size operating system, although evaluation thereof largely awaits the actual specification results. (NEDO)

Hydraulic mechanism of siltation in approach channels and harbors. Siltation ni yoru koroter dot hakuchi maibotsu no suiri kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Irie, I [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering; Murakami, K; Tsuruya, H [Ministry of Transportation, Tokyo (Japan). Port and Harbour Research Inst.

1991-11-20

The phenomena that clay or mud is carried away by waves or currents and deposited in approach channels and harbors are called siltation, and hinder often seriously the navigation of vessels and their arrival at as well as departure from wharves, etc.. In this paper, the hydraulic mechanism of siltation in harbors and approach channels in the sea area is chozen in particular, and waves and currents as the external force governing the travel of bottom mud, the properties of sunken mud, the supply source of sunken mud in approach channels, and grasping of the mud sinking mechanism as well as countermeasures against mud sinking are stated mainly centering around the results obtained from the in situ observations at Kumamoto Port and Banjarmasin Port and their mathematical calculations. The bottom mud traveling mechanism has been accepted as a study subject respectively from such wide viewpoints as river engineering, agriculture, environmental engineering, sanitary engineering, chemical engineering and mechanical engineering, and in addition, it has been under study by coastal engineering. Siltation under the wave actions is still in the state of research even in advanced countries in America and Europe. The siltation research in Japan has a short history, but this is the field which must be coped with positively. 19 refs., 17 figs.

Study of hydrocarbon emission in small direct injection engines; Kogata DI diesel kikan ni okeru teifukaji HC haishutsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tsurushima, T; Zhang, L; Ueda, T; Fujino, R; Yokota, K [Isuzu Advanced Engineering Center, Tokyo (Japan)

1997-10-01

The cause of unburned hydrocarbon emission in small DI diesel engines at light load was studied. An optically accessible engine which was enabled to visualize the squish area was used to investigate the behavior of spray, mixture distribution and so on. Based on these observations and engine tests, the factors such as the direct impingement of liquid phase fuel spray to the combustion chamber wall the unevenness of fuel spray among holes and spreading of the fuel droplets, mixture and flame to the squish area were supposed to be the cause of forming HC emission. 18 refs., 10 figs., 2 tabs.

Survey of implementation plan constructed for `the New Earth 21 Project`; Chikyu saisei keikaku no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

It is necessary to establish scenarios for reducing CO2 emissions and for developing CO2 emission control technologies to obtain a global consensus, using appropriate analytical models. For modification of the DNE-21 (Dynamic New Earth 21) model, it has a category designated as innovative technologies not involving CO2 emission and an optional consideration for the absorption of atmospheric CO2 by biomass. A global carbon circulation model, including vegetation in its scope, is also incorporated. Major results of the simulation are shown. When 20% reduction in CO2 emissions is required for only OECD countries after the year 2020, it has been demonstrated that CO2 concentration in the atmosphere will reach as high as about 900 ppm in 2100 due to CO2 emission by developing countries, and will not be a tolerable level. Under the condition that CO2 concentration in the atmosphere is controlled at 450 ppm in 2100, the amount of renewable source of energy from photovoltaic power generation and biomass will increase and technologies of CO2 recovery and storage will decrease. Research and development of the production of methanol from recovered CO2 will be adopted as innovative technology for CO2 measures. 69 refs., 112 figs., 79 tabs.

Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

Investigation and study on each technique and example of intelligent planning; Intelligent planning no kakushu shuho to jirei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-11

Various problems on intelligent planning (IP) and the tendency of basic technology were investigated. For each technique of IP, a Petri net and mark graph have been widely used as the modeling and analysis methods of a discrete event system. Moreover, various planning problems were modeled by a traveling salesman problem, and the efficient solution of the traveling salesman problem has been studied simultaneously. The tendency of the basic technology and application system viewed from an example of intelligent plant planning was investigated as an applied field of planning technology, with importance attached to the production system and robot planning. In the scheduling technology of the production system, the activation of an AI study and a new theory (i.e., architecture study) based on natural science information was investigated with the transition in the world as a trigger. A robot system has been planned in a wide range such as the environmental information acquisition planning of a robot. 202 refs., 69 figs., 4 tabs.

Fiscal 1997 survey report. Survey on the innovative well drilling technology; 1997 nendo chosa hokokusho. Kakushinteki kosei kussaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In the geothermal drilling, reduction of the cost of well drilling is an important subject for technical development. The geothermal resource development tends to be made at higher temperatures and at deeper wells. In the present drilling technology, the cost is rising with the exponentially increasing depth and temperature, and there is also occurring the technical limit. Accordingly, the survey clarified the limit of the present drilling technology/cost to point out the research trend of the drilling technology as substitute for the present one, possibilities of the introduction, and the R and D target and subjects. As to latest drilling systems abroad and in Japan, the following were surveyed to study and extract promising technologies and systems: improvement/application of drilling equipment/materials (enhancement of heat resistance of the main drilling equipment, etc., cooling effects of top drive, heat resistance verification of MWD tools, PDM, tricone bits, multi-stage cementing tools, etc.), heightening of drilling rates, trend surveys of slim hole drilling, control drilling, well maintenance/workover, and well design technology. 68 refs., 73 figs., 40 tabs.

Investigation of nitrous oxide (N2O) abatement technologies. 2; Asanka chisso (N2O) no teigen taisaku ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Emission amount of nitrous oxide (N2O) from anthropogenic sources is analyzed, and reduction effects by the abatement technologies are evaluated. The concentration of nitrous oxide in the atmosphere continues to increase and emissions from agricultural and ecosystem sources are drawing particular attention. For the emission of N2O in Japan, 8.28 Gg-N2O per year is emitted from fossil fuel combustion facilities, 6.95 from waste incineration facilities, 22.5 from transportation vehicles including automobiles, 26.7 from the chemical industry including establishments engaged in adipic acid production, 2.1 from sewage treatment facilities including septic tanks, 6.3 from farmland, and 7.1 from livestock excrement. For the N2O abatement technologies for different sources, fuel improvement, high temperature combustion, acceleration of reduction decomposition reaction, and development of catalysts are significant for the combustion technologies. In connection with N2O discharged in the process of adipic acid production, major businesses have internationally committed to up to 99% abatement of the N2O emissions by 1998. With regard to wastewater and sewage treatment facilities and septic tanks, improvement in COD/NO-N ratio, retention period, pH level, and reduction process is pointed out. 204 refs., 70 figs., 53 tabs.

Fiscal 2000 survey report. Survey and study of constellation satellites technology; 2000 nendo chosa hokokusho. Konsutereshon eisei gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demands for constellation satellites were surveyed and satellite systems were studied for extracting basic technical tasks relative to constellation satellite systems and for drafting space verification plans. For a constellation satellite system to accomplish its missions, two or more satellites have to be simultaneously navigated. It is assumed that its field of application will cover earth observation, information communication, risk management, disaster prevention, and the like. With such applications taken into consideration, surveys and studies were conducted about the need and marketability of constellation satellites, need of state-level involvement, and requests for missions to be imposed on a constellation system. For plural satellites to satisfy mission requests by coordinating with each other, it will be necessary to develop basic technologies, such as navigational guidance, communications control, system autonomous management, and operation on the ground. Functions and performance that a constellation satellite system are requested to have and basic technologies to be studied and developed were extracted, and space verification plans were drafted. (NEDO)

Report on `Survey of commercialization of intellectual ownership such as patent rights`; `Tokkyoken nado chiteki shoyuken no jitsuyoka ni kansuru chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A survey was conducted on research results in industrial circles, universities, etc. in the U.S., Europe and Japan, especially the state of how intellectual ownership such as patent rights is handled and the present situation of the commercialization of intellectual ownership, proposing problems and measures to be taken for promotion of practical use of excellent research results in Japan. The most important thing obtained from the survey is that study jointly by industrial circles and universities in the U.S. and Europe is much more advancing than that in Japan and is firmly established not only in industrial circles, universities and national research institutes, but in the whole society, actually producing a lot of favorable results. For Japan to catch up with the U.S. and Europe, needed is not only accumulation of the ideas in the past, but drastic measures to be taken from a new point of view. Concretely, it was proposed that by belonging intellectual properties such as patent rights to universities/research institutes and transferring their disposal rights to them, royalties of licenses are given back to inventors as incentives, and that as a body promoting the transfer to the industrial circle, `management organization` to which private vitality is introduced is established in universities/research institutes in order to promote interconnection between the industrial circle and universities. 15 refs., 35 figs., 36 tabs.

Survey on the life cycle system of a product with shared information; Joho kyoyugata product life cycle system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report provides and proposes new concept and optimization technology on the life cycle system of product for emission minimum. For the proposed life cycle system of product with shared information, the global emission minimum is realized by considering the final emission, the information is given to the product and shared in all the life cycle system, the information sending function is considered from the product, and the information necessary for material processing are actively used. For this life cycle system of product, development of the information model for the system, development of the technology of data saving, renewing, searching and sending, development of sensing and re-using technologies of the product for life cycle, development of the technology attaching information in the product for emission minimum, design of the guidelines of material composition, and research and development of materials for emission minimum are extracted and provided as tasks. 26 refs., 69 figs., 8 tabs.

Analysis and model-tests on vortex-induced oscillation of bridges; Kyoryo no uzu reishin ni kansuru sanjigen oto kaiseki to fudo jikken

Energy Technology Data Exchange (ETDEWEB)

Yamamura, N. [Hitachi Zosen Corp., Osaka (Japan); Ogasawara, M. [Kansai Electric Power Co. Inc., Osaka (Japan); Shiraishi, N. [Maizuru College of Technology, Kyoto (Japan); Nanjo, M.

1996-07-21

In order to predict the three-dimensional response to vortex-induced oscillation of bridges, a model was investigated using the aerodynamic force coefficient including vortex-induced and self-excited forces, and the nonlinear response coefficient expressing constancy of response to vortex-induced oscillation. In the analysis, change of frequency in wind by the self-excited force, aerodynamic damping term, effect of the mode, and correlation of the vortex-induced force along member axis were taken into account. The aerodynamic force and nonlinear response coefficients were identified from the homogeneous and turbulent flow results of wind tunnel tests using a two-dimensional spring support rigid body model with varied damping factor. The aerodynamic damping term can be estimated from the nonlinear aerodynamic force coefficient, but it was enough to calculate it from the quasi-stationary coefficient in general bridge profiles. The correlation of the vortex-induced force was obtained from measurements of the vertical variation components of trailing flow under the resonance state, or the pressure distribution of the member surface. When comparing to the wind tunnel test of three-dimensional model of cable-stayed bridge, the response amplitude by the present analysis method was consistent well with the test results rather than by the method in which the amplitude of two-dimensional model was corrected. 10 refs., 4 figs., 3 tabs.

Studies on connecting structure between steel shell and steel reinforced concrete; Kokaku to tekkotsu tekkin concrete tono ketsugo kozo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Morimoto, A. [Kinki University, Osaka (Japan). Faculty of Science and Engineering; Morikawa, H.; Ito, N. [Metropolitan Expressway Public Corp., Tokyo (Japan)

1996-02-15

On the insert reinforcing bar structure for the connecting part of the main tower of cable stayed bridges, this paper reports verification results on a load resistant safety with a full-scale model, structure analysis and construction work. The basic structure was composed of a drilled steel shell, inserted reinforcing bars, fixing structure of bars in lining concrete of the shell and a pressure bearing plate. As an experimental result, the connecting part had a sufficient load carrying capacity against both tensile and compressive loads. The shear stress of the insert reinforcing bar structure was estimated successfully under von Mises`s condition. The shear spring constant in deformation characteristics was linearly proportional to an inserted reinforcing bar ratio. In earthquake, nearly 60% of an allowable compressive load was transferred to concrete through the pressure bearing plate. The analytical results of load resistant deformation characteristics of the connecting part well agreed with experimental ones, and the proposed analytical model was applicable to estimation of a dynamic behavior. 5 refs., 22 figs., 4 tabs.

Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research related to hydrogen gas turbines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu. Suiso gas turbine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper describes development of hydrogen gas turbines from among the comprehensive discussions on hydrogen utilizing subsystems. Hydrogen and oxygen gas turbine cycle has varying optimal conditions of plant efficiency depending on fuel patterns. The regenerative cycle may have the turbine inlet temperature at about 1,000 degrees C. The inlet pressure would be ten and odds atmospheric pressure. It is better to keep the inlet temperature higher in order to obtain high specific power. Reduction of power generation cost in using this plant requires that construction cost be decreased, and the specific power be increased if the plant efficiency (in other words, running cost) is assumed constant. Further development is required on technologies to use higher temperatures and pressures. For that purpose, discussions should be given on material development, structural design, and inspection. Hydrogen gas turbines, which present low pollution depending on combustion methods, have great significance for such social problem as environmental contamination. In terms of economy, since hydrogen gas turbines depend on efficiency and fuel unit cost, the evaluation thereon may vary depending on how well the regenerative gas turbines have been established, in addition to future change in hydrogen price and the technologies to use higher temperatures and pressures. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and research on peripheral technologies (Research for aircraft engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Koku engine ni kansuru kenkyu (furoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-05-01

This paper introduces two out of six theses related to hydrogen fueled aircraft engines presented at the First World Hydrogen Energy Conference held in Miami in March 1976. One thesis mentions several initial prospects related to terrestrial requirements on hydrogen fueled transport aircraft. Liquefied hydrogen is attractive for large long-distance transport aircraft. Its high energy content can reduce the take-off full load weight by more than 30%, enhancing the economic effect of the aircraft. Saving fossil fuels will require national policy decisions in the near future, where introduction of liquefied hydrogen is more advantageous for long-distance aircraft. However, its introduction into wide-body transport aircraft being the major consumer requires transportation companies and airport authorities to carry out joint development with transport aircraft makers and liquefied hydrogen suppliers. The second thesis describes special natures of fuel subsystems for liquefied hydrogen fueled aircraft. Requirements to major fuel system elements and operation characteristics require evaluation as a comprehensive system, rather than as individual component criteria. In addition, hardware, experience and fuel systems as they are now in space development may not necessarily serve for the purpose. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on hydrogen utilizing subsystems and researches on peripheral technologies (Research related to automotive engines); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper discusses hydrogen fueled automotive engines. Because hydrogen has a very wide ignition mixture ratio limit for spark ignition engines, very lean combustion is possible without a need of throttling, and thermal efficiency in partial load is high. Thermal efficiency while a car is being driven is reportedly higher by 30% to 50%. Values for CO and CH in exhaust gas are negligible, while NOx is at about the same degree as in gasoline engines, which can be made extremely low during lean burn operation. The spontaneous ignition temperature is higher by about 200 degrees C than that of light oil, which presents difficulty in use for diesel engines. Because of small ignition energy and high combustion velocity, excessively early ignition and reverse ignition can occur easily. Hydrogen would be promising if new manufacturing systems are developed and production cost is reduced, and on the other hand, if petroleum price rises sharply. Hydrogen is also expected as a measure to prevent pollution, including that from soot, odor and CO2. The largest difficulty is in the transportation method, and the only possible method at the present is transportation in liquefied hydrogen form. However, practical application will have such problems as tanks, feeding devices, and cost. Development is desired on light-weight metallic hydrides. Technologies for safety and engine performance must also be developed. (NEDO)

Micromotors making use of electric field conjugate fluid (ECF). Proposition for Re-type ECF micromotor and study of its miniaturized version performance by experiment; Denkai kyoeki ryutai (ECF) wo oyoshita micromotor. RE gata ECF micromotor no teian oyobi bishoka tokusei no jikkenteki kento

Energy Technology Data Exchange (ETDEWEB)

Kondo, Y.; Yokota, S.; Nemoto, T. [Tokyo Institute of Technology, Tokyo (Japan); Otsubo, Y. [Chiba University, Tokyo (Japan); Edamura, K.

1999-01-15

A stator electrode (SE)-type ECF micromotor and a rotor electrode (RE)-type ECF micromotor are proposed, and have been tentatively constructed, both making use of ECF in which a jet flow is generated upon application of an electrostatic field across line electrodes. At the beginning, experiments are conducted to establish relationship between the impressed voltage and the number of revolutions in the RE-type micromotor that is expected to generate more torque than the SE-type micromotor. Next, the RE-type micromotor is miniaturized, and experiments are conducted to study the changes in power density and efficiency brought about by miniaturization. (translated by NEDO)

Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

Empirical analysis of consumer decision making processes on setting up residential photovoltaic systems; Jutakuyo taiyoko hatsuden system no donyu ni kansuru ishiki bunseki

Energy Technology Data Exchange (ETDEWEB)

Iuchi, M; Okawara, T; Tsuchiya, T [Central Research Institute of Electric Power Industry, Tokyo (Japan); Konakayama, A [Tokai Univ., Tokyo (Japan)

1996-10-01

Inquiries are made to consumers (monitors) who own a photovoltaic power generation system at their houses, and their replies are analyzed for isolating the factors involving the purchase of this domestic power generating system. A large part of the monitors are 40-50 years old males in the relatively high income bracket. They are very interested in problems of global environments, resources, and energy, and are inclined to assume value-consciousness and life-style which encourage them to love health and nature, participation in social functions, and decision-making. The need for the protection of global environments occupies more than 90% of the reasons for their adoption of photovoltaic power generation. The monitors strongly feel, however, that they paid very much for the apparatus although they were granted some subsidies. As for motives for their acquisition of the system, their answers are categorized into four groups according to their responses as to whether (or not) they expect economic merits though dependent on future development and whether (or not) they accept the current energy policies. The result shows that some monitors think like average citizens. 17 refs., 22 figs., 11 tabs.

Fiscal 2000 survey report on the survey and research on green technology industry; 2000 nendo green technology industry ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The approaches of the Government and local autonomies to green technologies are surveyed toward the construction of a green technology industry. The present activities and future outlook of environmental industries interested in green technologies are surveyed and examined, the green technologies here including (1) energy conservation measures and development of non-fossil fuels, (2) energy-related and environmental measures for countering global warming, (3) waste treatment measures for countering dioxins and endocrine disrupters. A survey is conducted of the outlines and future trends of green technology related important studies now under way at laboratories and research institutes of universities, the Government, and private-sector corporations. Based on the results of the surveys, important subjects of technical development in green technologies are extracted and studied for the possibility and outlook of their practical application. Tasks to discharge and problems to occur before they are introduced to the market are also evaluated and confirmed. Based on the results of the research and development of green technologies, actualities of environmental industries are taken up, and the problems and tasks to be settled before environmental technologies are introduced to the market are investigated and studied. (NEDO)

Investigation on chemical heat pump using calcium-chloride; Enka calcium no suiwa dassui hanno wo mochiita solar chemical heat pump ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Arai, T; Saito, Y [Meiji University, Tokyo (Japan)

1997-11-25

With an objective of developing a room heating system utilizing a solar chemical heat pump, an experimental system was fabricated to evaluate its performance. Steam was employed as a working gas, and for a reaction material, calcium-chloride was used, which has a reaction temperature zone permitting safe use and fitting the purpose among other hydrate systems and has high standard enthalpy in hydration. Water was used as a solar heat transferring medium. The system operates under the following principle: a container I is filled with hydrated salt and a container II with water, the two containers being linked with a pipe interposed with a valve; heat is inputted and outputted by performing charging and discharging alternately; and the role of a heat pump is played by deriving from environment the heat of water evaporation in the container II during discharging. The COP must take into account the electric power consumption of the water circulation pump to transfer solar heat. A COP of 0.256 was derived as a result of the experiment. 3 refs., 5 figs.

Study on the distribution of streaming potential while groundwater pumping up; Chikasui no kumiage ni tomonau ryudo den`i hassei ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Sato, H; Shima, H; Sakurai, K [OYO Corp., Tokyo (Japan)

1997-10-22

This paper describes effectiveness of water channel prospecting by means of streaming potential method. To investigate the distribution of streaming potential on the ground surface while groundwater pumping up, some laboratory experiments were performed. A system was constructed, in which fluid is flowed in an experimental cistern from its both ends and self-flowed through a strainer pipe fixed for flowing out the fluid at the center of the cistern. Streaming potential with the flowing of the fluid was observed. Positive streaming potential waveform was generated with the flowing of the fluid, and the potential increased with approaching the strainer pipe. A groundwater pumping test facility was used as a field test site. There was a positive maximal point of potential distribution at about 30 m far from the pumping well in the southeast direction. The potential gradually decreased in the eastern part from the maximal point. The potential steeply decreased in the northwest direction from the pumping well. From these experiments, it was found that the groundwater flow and underground structures can be reflected by the distribution of streaming potential, and that the present method is effective for water channel prospecting. 3 refs., 8 figs.

Survey on the construction of realization scenario of large-scale revegetation of arid regions; Daikibo ryokuka no jitsugenka scenario sakusei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In order to fix carbon dioxide as a measure to mitigate global warming, research of large-scale revegetation of arid regions has been conducted toward the ultimate goals of systematizing revegetation technologies centered on securing and using water resources, evaluating the feasibility of arid revegetation by extending the viewpoint to examine even rainfall increase by artificial means, and establishing a strategic program for large-scale revegetation. A trial revegetation feasibility map was made for a selected target region in Western Australia, and rough revegetation steps were formulated. Selection of proper region, introduction of technology, and planning were conducted by grasping environment of the target revegetation region. As a result, it was found that growth of plants is vigorous at the catchment areas due to the surface water transfer along the topography of surface in spite of poor rainfall. Obstruction of plant growth is partly caused by the corrosion of soil and accumulation of salt, but mainly caused by the shortage of water. Based on these data, ranking of proper regions was evaluated. When the technology is introduced in the region with A-rank, several times of water can be collected. 60 refs., 61 figs., 30 tabs.

Survey on chemical engineering technologies for the global environmental protection; Chikyu kankyo hozen no tame no kagaku kogakuteki taisaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

The present paper suggests chief measures to suppress and reduce global greenhouse gases. Under the control of artificial environments such as bioreactor, hydroponics and vegetable factory, a very high fixing rate of CO2 can be obtained, but CO2 generation accompanying electric power consumption is also large. It is preferable to use methane as resource by reforming reactions or selective oxidative reaction. In the recovery technique of fluorocarbon, 100% recovery is desirable. Techniques for decomposing recovered fluorocarbon and converting it to harmless material are the most backward ones. Understanding of essential structural relationship of coal is necessary for establishing combustion technique for the reduction of N2O. The integrated power generation system composed from solid electrolyte type fuel cell and coal-gasifying process, high-performance, superheat pump system form scientific technology imposing no burden on the global environment. Establishment of purification technique for industrial- or living-related drain inflowing to a closed water area system, establishment and reinforcement of inspection system for oil spill in the oceans in a global scale are required. 240 refs., 63 figs., 30 tabs.

Research on elaboration of the action plan for the New Earth 21; `Chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Elaboration of the action plan for the New Earth 21 plan proposed by Japan in Houston Summit was researched. In fiscal 1995 three types of energy supply/demand scenarios, sensitivity analysis under various conditions, and cases presupposing CO2 emission regulations or not were evaluated by analysis toward 2050 using the New Earth 21 Model (NE 21 Model). Energy-saving is important, and CO2 recovery/treatment technology is introduced according to CO2 emission regulations, while attention is focussed on biomass energy. The issue of solar and wind power generation is cost reduction. In a presupposed horizontally integrated energy system, methanol represents an important intermediate energy. As a whole, CO2 reduction can be achieved by various combinations of energy-saving, introduction of regenerative energy, and CO2 recovery/treatment technology. Case studies of the action plan were conducted by unifying the evaluation criterion on coal IGCC, photovoltaic generation and biomass. The NE 21 Model was useful for elaboration of the reduction scenarios of CO2 emission. 26 refs., 84 figs., 28 tabs.

Improvement of prediction accuracy of large eddy simulation on colocated grids; Colocation koshi wo mochiita LES no keisan seido kaizen ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Inagaki, M.; Abe, K. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

1998-07-25

With the recent advances in computers, large eddy simulation (LES) has become applicable to engineering prediction. However, most cases of the engineering applications need to use the nonorthgonal curvilimear coordinate systems. The staggered grids, usually used in LES in the orthgonal coordinates, don`t keep conservative properties in the nonorthgonal curvilinear coordinates. On the other hand, the colocated grids can be applied in the nonorthgonal curvilinear coordinates without losing its conservative properties, although its prediction accuracy isn`t so high as the staggered grid`s in the orthgonal coordinates especially with the coarse grids. In this research, the discretization method of the colocated grids is modified to improve its prediction accuracy. Plane channel flows are simulated on four grids of different resolution using the modified colocated grids and the original colocated grids. The results show that the modified colocated grids have higher accuracy than the original colocated grids. 17 refs., 13 figs., 1 tab.

Study on load levelling by means of the control of air conditioner operation; Kuchoki kado seigyo ni yoru fuka heijunka ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Sasaki, H. [Hiroshima University, Hiroshima (Japan); Sadakuni, S. [Japan Broadcasting Corp., Tokyo (Japan)

1995-04-20

The recent drastic increase in the number of air conditioners has caused sharp and narrow peaks in summer seasons due to the inherent temperature sensitive characteristics. The authors proposed to reduce the peak power demand by controlling air conditioner operations, verifying its effectiveness on peak demand clipping. However, the former study has shortcomings in that any qualitative treatment of room temperatures or pleasant feeling was not attempted and it did not provide a way of assessing peak demand clipping in a power system as a whole. In this paper, we shall first propose a new control method that can compromise pleasant feeling and reduction in power demand. Although air conditioners are used to pursue `pleasant feeling`, this contradicts to reduce power consumption and further more the concept of `pleasant feeling` is very vague. Hence, `Weber-Fechner`s law` is utilized to quantify the pleasant feeling which is treated as fuzzy quantity. Fuzzy co-ordination method is used to compromise power demand curtailment and pleasantness. In the second part of this paper, we shall propose an approach of assessing the amount of peak load clipping when the newly proposed control strategy is adopted in a real size power system: A decrease in the required generation capacity is estimated provided that the Loss of Load Probability (LOLP) is maintained at the same level before and after the application of the new control strategy. The reduction can be regarded as a dividend of load management. 5 refs., 9 figs., 5 tabs.

FY 1999 report on investigation on establishment of body function database; 1999 nendo shintai kino database no kochiku ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The investigation is made to provide the data which widely cover various characteristics of aged persons for the general designers who design equipment and environments for aged persons. It is found, by the tests for measuring sight and hearing sensations of the aged, that they generally need higher sound to hear; frequency of alarming sound is preferably lowered from 3,000 to 4,000Hz now used for the equipment to 1,000 to 2,000Hz, and the level at which sound can be heard is significantly different from that at which the announcement can be understood. For evacuation order or the like, for example, it is necessary to announce the disaster site and evacuation routes, which the aged hear for the first time, especially slowly and distinctively. The database of body functions of the aged are improved by correcting the problems associated with depth of strata and poor prospects, frequently pointed out by those who look up the data from the daily actions, in such a way that the system can be easily looked at from notices for each function position of the product and also from the related human characteristics. (NEDO)

Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Itagaki, H. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H.; Ito, S. [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M.

1996-12-31

Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

Research on active magnetic levitation of multiple high-T{sub c} superconductors; Fukusu no baruku chodendotai wo mochiita akuteibu jikifujo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nishi, K.; Tachi, K.; Sawa, K. [Keio University, Tokyo (Japan); Iwasa, K. [Francis Bitter Magnet Laboratory, Cambridge (United States); Nagashima, K.; Fujimoto, H. [Railway Technical Research Institute, Tokyo (Japan); Miyamoto, T.; Tomita, M.; Murakami, M. [Superconducting Research Laboratory, Tokyo (Japan)

1999-11-25

This paper describes a new [electromaglev] system, in which multiple Y-Ba-Cu-O bulk superconductors are levitated on a DC magnet. In this system, we have succeeded in controlling the levitation height and force like the case of a single bulk system. We also simulated the total levitation force for multiple bulks, which were in good agreement with the experimental results. (author)

Fiscal 2000 survey report. Research on creation of microspheric photonic material; 2000 nendo bishokyu photonics zairyo no sosei ni kansuru kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Experiments were conducted under microgravity for findings on the creation of microspheric photonic materials which are high in sphericity. The experiments were carried out at the fall type microgravity facility of Japan Microgravity Center (JAMIC). In the experiments on the ground surface and under microgravity, glass specimens of 3BaO-97B{sub 2}O{sub 3} mol%, 4BaO-96B{sub 2}O{sub 3} mol%, and 2SrO-98B{sub 2}O{sub 3} mol% were tested. They were heated, melted, and cooled for the on-site observation of phase splitting in them. It was found as the result that, in the case of specimen 3BaO-97B{sub 2}O{sub 3}, the phase splitting start under microgravity was similar to that on the ground surface while the nucleation velocity was lower under microgravity. Specimen 2SrO-98B{sub 2}O{sub 3} mol% exhibited an approximately 0.5-second delay in its phase splitting start under microgravity as compared with its ground surface behavior. As for the nucleation velocity under microgravity, the value was same as that on the ground surface in the first half but, in the second half, it was lower than that on the ground surface. The said approximately 0.5-second delay in the phase splitting start was, when the cooling rate was taken into consideration, attributed to an approximately 6.5 degrees C fall in the phase splitting start temperature, and this suggested that phase splitting was suppressed under microgravity. (NEDO)

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Fiscal 1999 technical survey report. Survey of energy conservation technologies in Japan; 1999 nendo kokunai no sho energy gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

NEDO (New Energy and Industrial Technology Development Organization), in its effort to implement a joint project with importing countries, endeavors to popularize energy conservation technologies by introducing them into plants in the importing countries and by demonstrating their validity on real systems. Energy conservation technologies in use in Japan's steelmaking, cement making, chemical, and oil refining industries were reassessed in view of their usefulness in the above-said project. During the reassessment, they were analyzed also for cost effectiveness for the scales on which they would possibly be introduced. Ninety-four technologies were reassessed, which involved the top pressure recovery facilities, continuous casting facilities, high frequency melting furnace, and high efficiency sintering furnace ignition device, these for the steelmaking industry; the materials crushing vertical roller mill, NSP (new suspension preheater) type cement calcination kiln, finishing process preliminary crusher, urban wastes conversion into materials for cement making or into fuel, these for the cement making industry; the multi-effect evaporator for an ammonia manufacturing process and the device for collecting waste heat at the outlet of a synthetic gas compressor, these for the chemical industry; and reduction in the amount of injection steam by use of vacuum distillation tower top steam recycling, etc., these in relation with oil refining facilities. (NEDO)

Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

1997-10-01

Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

Investigations on an environment friendly chemical reaction process (eco-chemistry). 2; Kankyo ni yasashii kagaku hanno process (eko chemistry) ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to structure a chemical reaction process that does not discharge a large amount of waste by-products or harmful chemical substances, or so-called environment friendly process, investigations and discussions were given based on the results derived in the previous fiscal year. A proposal was made to reduce environmental load on development of oxidized and dehydrogenated catalysts that can produce selectively ethylene, propylene and isobutylene in an oxidation process. In liquid phase oxidation, redox-based oxidation and solid catalyzation of automatic oxidation reaction were enumerated. In acid base catalyst reaction, development of ultra strong solid acid was described to structure no pollution discharging process. In the fine chemical and pharmaceutical fields, the optical active substance method and the position-selective aromatics displacement reaction were evaluated to reduce environmental load. A questionnaire survey performed on major chemical corporations inside and outside the country revealed the following processes as the ones that can cause hidden environmental problems: processes discharging large amount of wastes, processes treating dangerous materials, and processes consuming large amount of energy. Development of catalysts is important that can realize high yield, high selectivity and reactions under mild conditions as a future environment harmonizing chemical process. 117 refs., 23 figs., 22 tabs.

Performance analysis on utilization of sky radiation cooling energy for space cooling. Part 2; Hosha reikyaku riyo reibo system ni kansuru kenkyu. 2

Energy Technology Data Exchange (ETDEWEB)

Marushima, S; Saito, T [Tohoku University, Sendai (Japan)

1996-10-27

Studies have been made about a heat accumulation tank type cooling system making use of radiation cooling that is a kind of natural energy. The daily operating cycle of the cooling system is described below. A heat pump air conditioner performs cooling during the daytime and the exhaust heat is stored in a latent heat accumulation tank; the heat is then used for the bath and tapwater in the evening; at night radiation cooling is utilized to remove the heat remnant in the tank for the solidification of the phase change material (PCM); the solidified PCM serves as the cold heat source for the heat pump air conditioner to perform cooling. The new system decelerates urban area warming because it emits the cooler-generated waste heat not into the atmosphere but into space taking advantage of radiation cooling. Again, the cooler-generated waste heat may be utilized for energy saving and power levelling. For the examination of nighttime radiation cooling characteristics, CaCl2-5H2O and Na2HPO4-12H2O were tested as the PCM. Water was used as the heating medium. In the case of a PCM high in latent heat capacity, some work has to be done for insuring sufficient heat exchange for it by, for instance, rendering the flow rate low. The coefficient of performance of the system discussed here is three times higher than that of the air-cooled type heat pump system. 8 refs., 5 figs., 4 tabs.

Study on the living environment of semi-underground room with attached green house; Fusetsu onshitsu no aru hanchikashitsu no kyojusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Tsukayama, N [Ochanomizu University, Tokyo (Japan)

1996-10-27

In response to demand for the expansion of living space, the living environment of semi-underground room has been investigated. An attached green house (passive solar house) is adjacent to the semi-underground room. This is reinforced concrete construction, having flat type solar collector on its roof and lighting window in its north side. It does not have artificial air conditioners. Based on the measurements of daylight factor, artificial lighting is not required at the window in the daytime, but it is desirable to use daylight and artificial lighting together at the center. The performance of sound insulation depends on the high performance soundproof sash level. There is less daily temperature variation due to its large heat capacity, and less yearly temperature variation than the outside. By shielding the solar radiation, the insolation in the green house in summer can be restricted in the same as in winter. The insolation can be easily received in winter due to its large vertical intensity of solar radiation. The green house in the south side is useful for improving the living environment of semi-underground room. The temperature rise in the semi-underground room can be restricted by opening window in summer. It is desirable for the comfortable living to use artificial cooling to reduce the daytime temperature by 3 to 4{degree}C. In winter, it is comfortable to heat by 4 to 5{degree}C. 2 refs., 7 figs.

Features of vertical axis wind turbine and development of airfoils sections; Chokusen yokugata suichoku jiku fusha no tokucho to yokugata ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan); Nakayama, H [Oriental Kiden Company, Osaka (Japan)

1996-10-27

Features of a straight wing type vertical axis wind turbine (VAW) and its airfoil sections were studied. The wind turbine in which various aerodynamic work components are mounted on the rotation axis normal to the ground surface is named VAW. Like the airfoil section of aircraft, in lift type VAW, wind turbines were driven by lift 70-90 times as large as drag in some cases. Features of the VAW airfoil section which is a straight wing in plan and a fixed pitch wing (with a fixed angle to a blade support arm) in cross section, and those of wind turbines were studied. Some factors affecting the features, work principle and performance of VAW were clarified. On airfoil sections, products of each weight function and each corresponding aerodynamic factor (lift, drag and pitching moment factors) were plotted on an attack angle ({alpha}) axis. From the conditions for increasing the total sum of areas drawn by the products on the {alpha} axis, various characteristics required for airfoil sections were clarified. Such characteristics nearly agreed between an airfoil section for favorable starting characteristics and that for high efficiency. 3 refs., 7 figs.

Stability analyses of urban water supply systems with wastewater reuse; Toshi haisui no junkan riyo ni yoru mizu kyokyu anteika ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H.; Zhang, S. [Meijo Univ., Nagoya (Japan); Okada, N. [Kyoto Univ., Kyoto (Japan). Disaster Prevention Research Inst.

1995-10-20

Wastewater reuse can be considered as a type of water resource development which is expected to improve the aquatic environment, as well as the stability and reliability of municipal water supply systems. To this extent, wastewater reuse has been taken into account in the planning of water supply systems in several Japanese cities. However, to date the effect of wastewater reuse on water supply system stabilization has not been discussed quantitatively, and the relation between waster water reuse rate and water supply system stability has not been analyzed. In this study, a stochastic model has been presented to evaluate the stability of water supply systems with optimal wastewater reuse rate. Some theoretical analyses and numerical studies were performed, and all of the results have shown that the model is reliable for not only basic studies on water supply system stability, but also for practical use as well. 5 refs., 5 figs., 3 tabs.

Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

2000-10-25

The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

Studies on the friction and wear properties of synchronizer rings and gear cones; Shinkuro kiko ni okeru masatsu mamo tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Hayashi, K; Kunoki, T [COSMO Research Institute, Tokyo (Japan)

1997-10-01

The influence of materials of synchronizer rings, automotive gear oils and sulfur-phosphorus EP additives on the friction and wear properties of synchromesh system was studied by using a synchromesh friction tester. As a result, the durability was decreased by using the synchronizer ring made of copper alloys. The initial friction performance estimated by using the synchronizer ring made of resin have influence on EP additives, in particular some kinds of phosphorus type additives. 3 refs., 12 figs.

Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Itagaki, H [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H; Ito, S [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M

1997-12-31

Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

Achievement report for fiscal 1976 on Sunshine Program. Comprehensive examination of hydrogen-utilizing subsystems and research on peripheral technologies (Survey and research on hydrogen production by quinon method); 1976 nendo suiso riyo subsystem no sototeki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kinonho ni yoru suiso seizoho ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

The quantum yield and conversion efficiency are measured during photosensitized water decomposition at an n-type TiO{sub 2} semiconductor electrode built from a rutile type single crystal, and the role of the TiO{sub 2} electrode is clearly defined. A method is tested of acquiring a photoactive TiO{sub 2} semiconductor as an oxide coating and an oxide coating electrode is fabricated, and its characteristics are determined and then compared with the above-said measurements. A WO{sub 3} semiconductor is manufactured, and its characteristics are compared with the above-said measurements. The mechanism of photosensitized decomposition at a semiconductor electrode is examined, and guidelines are established to follow for improvement on efficiency in semiconductor electrode-aided hydrogen production. Dark and light reactions are caused to occur by adding methyl viologen, potassium ferrocyanide, and potassium ferricyanide, and the photochemical reaction characteristics are clearly defined. Oxygen is generated by use of chloroplast. Use of an acrylamide membrane and an osmotic membrane enables a continuous 48-hour test. A solar beam is concentrated on a TiO{sub 2} electrode for a reaction of Q+H{sub 2}O{yields}QH{sub 2}+1/2O{sub 2}{up_arrow} to occur. A reaction of QH{sub 2}{yields}Q+H{sub 2}{up_arrow} is caused to occur as an electrode reaction. A current of 3.7mA and a voltage of 2.4mV are recorded on a fine day at the beginning of October, and 0.4mA and 0.2mV on a cloudy day. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the hydrogen engine for airplane use); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kokukiyo suiso engine ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This study is aimed at using hydrogen as fuel for airplane engine in the study on the use of hydrogen energy to be made as one of the new energy developments. In the investigational study plan, technical/economical possibilities of the airplane engine using hydrogen as fuel and the airplane carrying the engine are grasped to make the details of the R and D clear by the end of FY 1976. By the end of FY 1974, the actual state in the world of the airplane engine using hydrogen as fuel and the airplane carrying the engine was grasped to make the problems clear. The detailed R and D are as follows. (1) Survey of the actual state of and the problems of the hydrogen engine in Japan and abroad (to be conducted in FY 1974). (2) Consideration of the conceptual design of the potential hydrogen engine, and possibility of the commercialization and prediction of the time of the commercialization (to be conducted in FY 1975). (3) Survey of type, performance, etc. of the airplane carrying hydrogen engine, and the actual economical value and demand (to be conducted in FY 1976). This paper described the results of the survey on hydrogen general and hydrogen use airplane. (NEDO)

Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Research on actualities of Japanese industries' research and development potential); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (Nippon kigyo no kenkyu kaihatsuryoku no jittai ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For working out propositions on what the country should do and on what improvement industries should make for the strengthening of industries' competitive power on the market, analyses were conducted into the objects of research and development, organizations engaged in research and development activities, methods of evaluation, and the like. In concrete terms, studies were made on industries' roles in research and development activities and on the actualities of basic research and development potential, and then a survey was conducted through questionnaires and interviews about (1) tasks relating to corporation management and research and development potential, (2) development of research dedicated talent and its fluidity, and (3) problems feared to get worse in the future. Questionnaires were sent to 217 corporations or 577 people of whom 37.6% responded. Each item is described below. Under item (1), it is pointed out that basic research has shrunk as a whole, that pressure is on the increase urging that research directly increase profit, and that theme selection is made to match the business model. Under item (2), it is stated that post-doctorate researchers' knowledge is respected but that recruitment is another matter, and that fluidity of researchers between corporations will increase. Under item (3), it is pointed out that researchers are increasingly inferior in quality and that brain drain out of Japan is feared. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

Research and development cooperation project on environmental measurement using laser radar in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

As one of the international research cooperation projects, the research cooperation in developing laser radar for environment measurement started between Japan and Indonesia. The project is scheduled to be carried out in a 4-year plan starting fiscal 1993. In fiscal 1993, conducted were negotiations with Indonesia on its implementation and a field survey. Between January 6 and 15, 1994, the first field survey was made in terms of topography, climate, road network and traffic situation of Jakarta city, and the proposed sites for installation were reported. The paper also introduced the reception system on the Indonesian side and a request for technical learning through stay in Japan. The second field survey was conducted between February 27 and March 6, 1994. Indonesia requested that they want to make laser radar observation not only for the local area, but the one that covers industrial areas, central urban areas and residential areas. Incidentally, there was an opinion that it is important to elucidate the pollution mechanism. 19 refs., 43 figs., 6 tabs.

Research and development cooperation project on environmental measurement using laser radar in fiscal 1994; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper outlined activities in fiscal 1994 in the R and D cooperation project on a laser radar for environmental measurement. In the activities in fiscal 1994 of `the ODA laser radar development committee,` the committee held four meetings, two field surveys were carried out, and two researchers were invited from Indonesia. In the field survey, the environment in Jakarta city was investigated in terms of changes in population and number of the cars registered. Further, from data collected during 1994-1998 in the central Jakarta city, the following were made clear: the trend of a decrease in SO2, the trend of a rapid increase and an excess of NO2 content over the environmental standard, the status of pollution of which the level is close to the upper limit of the environmental standard of dust, etc. In the meeting of the policy study for the field survey at LIPI headquarters, Japan proposed a system which is constituted of a difference absorption laser radar, two Mie scattering laser radars, and a central processing unit. The sites proposed were studied in cooperation with Indonesia. 40 refs., 65 figs., 9 tabs.

FY 1996 annual report of investigation on biological fixation of carbon dioxide. 2; 1996 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Various kinds of biological fixation processes of CO2 were evaluated from the various viewpoints. Afforestation of tropical and temperate areas, greening of desert, biomass energy production in these areas by energy plantation, coastal mangrove plantation, fertilization with nitrogen and phosphate to outer ocean and coastal, upwelling zone fertilization with iron, and coral reef expansion combined with OTEC (ocean thermal energy conversion) were comparatively investigated as the selected measures. As a result, the cost of CO2 fixation by cultivation of sea weed and plankton was much higher than that of afforestation. The iron fertilization method which was considered to be one of the high CO2 reduction potentials might be economical. However, its effect could not be quantitatively evaluated. The afforestation of tropical and temperate areas seemed to be most feasible in a short term from the viewpoints of economy and environment. It was suggested that the establishment of a systematic water management technology could make greening and afforestation of desert. 76 refs., 27 figs., 28 tabs.

Fiscal 1994 technological survey report. Research study on polymer materials by precision polymerization; 1994 nendo seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In the paradigm that propelled polymer chemistry, there are involved the establishment of polymer concept, engineering plastics, regulation of higher ordered structure, and precision polymerization. The first two produced the polymer chemistry era in the 20th century. The regulation of higher ordered structure and the precision polymerization are the fundamental technologies supporting the polymer chemistry of the 21st century. The precision polymerization is a technology for regulating the stereospecificity, sequential structure, and molecular weight of polymers by regulating atoms and molecules and is referred to the following important techniques to be concrete. In the precision addition polymerization, stereospecific regulation and purification of active site to give living polymers are required while, in the precision condensation polymerization, regulation of condensation probability process to be secondary Marcov chain is necessary, as is the establishment of non-defect condensation condition avoiding high temperature deterioration and the like. In the biomimetic precision polymerization, key issues are the method of incorporating molecular recognition control and sequential structure control by living organs into an industrial process. If the higher ordered structure can be regulated by the precision polymerization, it is possible to obtain numerous high performance/high functional materials such as superconductors. (NEDO)

Report of international workshop on technical elements for aviation safety; Koku anzensei kojo no tame no gijutsu kadai ni kansuru kokusai kaigi wo kaisaishite

Energy Technology Data Exchange (ETDEWEB)

Terada, H. [National Aerospace Laboratory, Tokyo (Japan)

1999-06-05

The international workshop on technical elements for aviation safety was opened in Tokyo on March 15-17, 1999 with 75 domestic and overseas participants, and 18 reports. On aircraft operation, report was made on the research of a practical visual sense supporting equipment for cockpits to reduce workload of crew at takeoff and landing, and improve a safety. On human factor, report was made on the managers` recognition of their responsibility on safety in Titanic accident. On aircraft passenger cabin safety and emergency escape, discussion was made on the order of priority of 30 factors effective for improving a survival rate in crush accidents, and report was made on current R & D of flame retardant interior materials with less toxicity for passenger cabins. On aircraft body structure, report was made on the research on growth and propagation of fatigue cracks by more than 10{sup 8} cycle loading, and the simulation of complex loading to estimate residual lives of body structure. (NEDO)

Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

Report on an investigation into heat pumps in China in fiscal 1995; 1995 nendo Chugoku ni okeru heat pump system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper surveyed the present status, the status of spread, and the technical development of the technology of heat pumps for residential and industrial uses in China. Main examples of installation of heat pumps are cited below: steam drive absorption type refrigerators in Beijing; sea water heat source turbo heat pumps in Qingdao; hot water drive absorption type refrigerators in Beijing; oil-fueled absorption type water cooling and heating appliances in Beijing; ice latent heat storage airconditioning systems using electrically-driven screw chiller in Beijing; temperature rising systems using electrically-driven heat pump of the solar energy utilization warm water swimming pool in Guangdong Province; cooling water supply using waste heat utilization absorption type refrigerator of the alcohol plant in Shandong Province; timber drying systems using electrically-driven heat pump, and marine product cultivation systems in Quangdong Province; distillation systems using steam turbine heat pump in Jiangxi Province. The demand for heat pumps is expected to be 20 million units under the 9th 5-year plan, and the development of equipment is thought to go toward promotion of energy conservation, low noise, multi-type or multi-functional air conditioning equipment, and computer use. 137 figs., 40 tabs.

Study on estimating fluid force acting on a hull during maneuvering movement; Soju undoji no sentai ni sayosuru ryutairyoku no suitei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yukawa, K; Kijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-01

With types of general cargo vessel and VLCC vessel as the object of discussion, a method was discussed to estimate fluid force acting theoretically on a hull during maneuvering movement, taking frame line shape into consideration. A vortex model was improved by giving consideration of time-based decay on intensity of discrete vortex lines based on the Rankine vortex. Modeling of flow fields around a hull was attempted to deal with movements in which width and draft are small as compared with the ship length, and turning angle speed and deviation angle are small. It was assumed that the ship speed is slow and effects of waves can be disregarded. Specular images of the hull were taken with regard to free surface, and handled as a double body model. Speed potential to express flow fields around a hull is required to satisfy the following five boundary conditions of Laplace, substance surface, free vortex layers, infinity and exfoliation. The potential may be handled as a two-dimensional problem in a field near the hull by using assumption of a slender and long body and conformal mapping. It was found possible to estimate hull fluid force with relatively good accuracy. Fine linear coefficients derived from the estimation were used to have performed highly accurate determination on course stabilization. 5 refs., 6 figs., 2 tabs.

Fiscal 2000 survey report. Basic research on hot molding of amorphous ceramics; 2000 nendo amorphous netsukan ceramics seikeiho ni kansuru kiso kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Experiments were conducted on the plasticity processing of heat resistant ceramics making use of the viscous deformation of amorphous ceramics in the supercooled liquid temperature domain. Concerning the preparation of powder of amorphous ceramics, the plasma rotating electrode method of Institute for Materials Research, Tohoku University, was employed, and a bamboo leaf shaped amorphous flake was successfully fabricated by increasing the arc discharge current. In a search of texture easy to turn amorphous, it was observed that Al{sub 2}O{sub 3}-La{sub 2}O{sub 3} had a supercooled liquid domain of as large as 70K, and this enabled a conclusion that it was a promising candidate for hot molding in a supercooled liquid domain. In an experiment of molding in a supercooled liquid domain, Al{sub 2}O{sub 3}-Gd{sub 2}O{sub 3} was used in a press molding process. As the result, a compact bulk mold was obtained in a temperature domain far lower than in the case of conventional sintering. Crystallization had already advanced in all the molds experimentally fabricated by press molding, and this disabled a study of characteristics to be exhibited by an amorphous mold, but it was found that they had a compressive strength of approximately 1,800MPa. (NEDO)

Coal liquefaction in early stage of NEDOL process 1t/d PSU; 1t/d PSU ni okeru ekika shoki hanno ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ikeda, K.; Kawabata, M.; Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

To investigate the behavior of coal liquefaction reaction in early stage as a part of studies on the coal liquefaction characteristics using NEDOL process 1 t/d process supporting unit (PSU), coal slurry sample was taken from the outlet of slurry preheater located in the upflow of liquefaction reactors, and was tested. Tanito Harum coal was used for liquefaction. Preheater was operated under the condition of pressure of 170 kg/cm{sup 2}, gas flow rate of 64 Nm{sup 3}/hr, and at temperature up to 410{degree}C at the outlet, in response to the standard test condition. The slurry sample was discharged into a high temperature separator with temperature of 250{degree}C. Liquefaction was not proceeded at the outlet of preheater. Solid residue yielded around 80%, and liquid yielded around 15%. Gases, CO and CO2, and water yielded also small amount around 3%. The solid sample contained much IOM fraction (tetrahydrofuran-insoluble and ash), and the liquid contained much heavy oil fraction. Hydrogenation was not proceeded, and the hydrogen consumption was very low showing below one-tenth of that at the usual operation. Hydrogen sulfide gas was formed at early stage, which suggested that the change of iron sulfide catalyst occur at early stage of liquefaction. 1 ref., 5 figs., 2 tabs.

Studies on the utilization of inedible parts produced at processing the marine products. Part 1; Suisan haikibutsu no kodo riyo ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Kitamura, S.; Nomura, A.; Quinones, H. [Industrial Technology Center of Kochi Prefecture, Kochi (Japan)

1995-09-01

For the purpose of effectively using marine products in Kochi pref., analyses were made of the components of the following marine products: the head and inside of frigate mackerel disposed of at the time of producing dried frigate mackerel (an annual catch of the frigate mackerel is about 12000-15000 tons, almost half of which is used for processing for dried bonito), the head and other part of lobster disposed of at lobster restaurants (including the shell of lobster), the skin of lazard fish disposed of in boiled fish paste producing plants. The analysis was conducted in terms of the composition of coarse fatty and fatty acid, free amino acid, ATP related compounds, etc. As a result, the following were found out: in the fat of the head and inside of frigate mackerel, DHA (docosahexaenoic acid) and EPA (eicosapentaenoic acid) were included by 20-30% and 10%, respectively, and the fat is promising as supply source of high-grade unsaturated fatty acid; in the head and other part of lobster, chitin chitosan is included in addition to free amino acid such as glycine and alanine; in the skin of lazard fish, ATP related compounds such as inosinic acid are included, and the skin is useful for a raw material of the seasoning. 15 refs., 4 figs., 6 tabs.

Study on state grouping and opportunity evaluation for reinforcement learning methods; Kyoka gakushuho no tame no jotai grouping to opportunity hyoka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yu, W.; Yokoi, H.; Kakazu, Y. [Hokkaido University, Sapporo (Japan)

1997-08-20

In this paper, we propose the State Grouping scheme for coping with the problem of scaling up the Reinforcement Learning Algorithm to real, large size application. The grouping scheme is based on geographical and trial-error information, and is made up with state generating, state combining, state splitting, state forgetting procedures, with corresponding action selecting module and learning module. Also, we discuss the Labeling Based Evaluation scheme which can evaluate the opportunity of the state-action pair, therefore, use better experience to guide the exploration of the state-space effectively. Incorporating the Labeling Based Evaluation and State Grouping scheme into the Reinforcement Learning Algorithm, we get the approach that can generate organized state space for Reinforcement Learning, and do problem solving as well. We argue that the approach with this kind of ability is necessary for autonomous agent, namely, autonomous agent can not act depending on any pre-defined map, instead, it should search the environment as well as find the optimal problem solution autonomously and simultaneously. By solving the large state-size 3-DOF and 4-link manipulator problem, we show the efficiency of the proposed approach, i.e., the agent can achieve the optimal or sub-optimal path with less memory and less time. 14 refs., 11 figs., 3 tabs.

System approach on solar hydrogen generation and the gas utilization; Taiyo energy ni yoru suiso no seisei oyobi sono riyo system ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujii, I; Hirooka, N; Deguchi, Y; Narita, D [Meiji University, Tokyo (Japan)

1997-11-25

An apparatus is developed to establish a system which allows utilization of hydrogen safely and easily, and its applicability to a hydrogen system for domestic purposes is tested. The system converts solar energy by the photovoltaic cell unit into power, which is used to generate hydrogen by electrolysis of water at the hydrogen generator, stores hydrogen in a metal hydride , and sends stored hydrogen to the burner and fuel cell units. It is found that a hydrogen occluding alloy of LaNi4.8Al0.2 stores hydrogen to approximately 80% when cooled to 20 to 25degC, and releases it to 10% when heated to 40degC. The fuel cell uses a solid polymer as the electrolyte. The hydrogen gas burner is a catalytic combustion burner with a Pt catalyst carried by expanded Ni-Al alloy. The optimum distance between the burner and object to be heated is 22mm. High safety and fabrication simplicity are confirmed for use for domestic purposes. The system characteristics will be further investigated. 4 refs., 8 figs.

Reduction mechanism of dynamic loads on down wind rotor; Furyoku hatsuden system down wind rotor no doteki kaju no keigen kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Seki, K; Shimizu, Y; Yasui, T [Tokai University, Tokyo (Japan)

1997-11-25

Dynamic force on blades in a large wind mill changes with rotational speed for various reasons, such as wind shear that causes vertical distribution of wind velocity or titling angle. Therefore, a 2-blade system on a teetered hub is a practical selection for the coned, down-wind type. Use of teetered axis greatly reduces bending moment in the flap direction and that at the axis of rotation. An attempt was made to understand dynamic loads by inertial force resulting from oscillation of the blade rotating on the teetered axis, and thereby to avoid them. The in-plane load can be diminished to zero when the teetered axis is coincided with the center of gravity, but generally cannot be avoided when the blade is strained significantly, except it is operated at the rated condition. The in-plane load and bending moment can be avoided, when rotational freedom is given around the y axis. Dynamic load on a down-wind rotor can be avoided by use of universal joint. 3 refs., 6 figs.

Research report for fiscal 1998. Research into the recycling of plastic wastes into resources; 1998 nendo hai plastic no saishigenka ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The actualities in Japan are investigated of the types and quantities of plastic wastes, collection and recovery systems, and recycling technologies. Plastic wastes exceeded 9-million tons in 1996, of which 39% was effectively utilized while 61% was merely incinerated or used for reclamation. The 61% of the plastic wastes which are equivalent to oil resources in terms of the energy they contain is found dealt with in such ways, for which additional energy has to be consumed. Some problems are mentioned that occur in the CO2 gas reduction effort in the process of plastic waste recycling for each of its stages of production, distribution, assortment, recovery, and reuse. The problems involve the required reform into production designs and systems with the greatest importance attached to recyclability; share of the expenses between the producing and distributing parties and financial support to assortment/recovery systems; reform of consciousness of both people at large and the administrative organizations, mutual collaboration between them, and reasonable share of expenses between them; construction of a unified assortment/recovery system; expansion of the scope of use of recycled products and the building of environments that encourage their use; diversification of recycling methods and establishment of technologies therefor; and limits on the use of materials and products that generate heavy impacts on environments during their life cycles. (NEDO)

Study on the performance improvement of multiblade fans. Effects of suction cones; Tayoku fan no seino kaizen ni kansuru kenkyu. Suction cone no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kuratani, F.; Ogawa, T. [Hyogo University of Teacher Education, Hyogo (Japan); Yamamoto, S.

1999-07-25

In order to improve the performance of a multiblade fan, the effects of three types of suction cones of the fan casing on the fan efficiency and noise are investigated experimentally. The first type of the suction cone is the insertion type, which is inserted into the inside of the fan impeller. The second type is the extrusion type, which extrudes outside from the casing surface. The third type is the combination type of two types. The results of those three types are compared with those of the commonly used suction cone. The followings are made clear: (1) The insertion type and the extrusion type are effective in improving the efficiency and reducing noise. (2) The optimal lengths of the insertion and the extrusion exist. (3) The combination type is more effective in improving the efficiency. (4) The combination type with the skewed cutoff of the fan casing shows the best effect. (author)

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

1996-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

Report on a survey in fiscal 1999. Survey on movements in technologies related to phytoremediation; 1999 nendo phytoremediation ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey is intended to discuss the status quo in movements of technologies related to phytoremediation (PM) that utilizes metabolic functions of plants, the overseas situation thereof where the PM application has advanced, and the future technological problems. The PM can be divided largely into the following four categories according to the actions of plants: 1) phyto-extraction - absorbs substances dissolved in water directly or through actions of leguminous bacteria to purify the water or soil; 2) phyto-transformation - action to absorb polluting substances into plant bodies and decompose them; 3) phyto-stimulation - rhizospheric microorganisms are activated by enzymes secreted from roots to decompose chemical substances; and 4) phyto-stabilization - actions to fix or stabilize polluting chemical substances by actions of substances secreted from plants and/or leguminous bacteria in soil and interactions with soil particles. Japan's independent researches have derived such researches as a research to utilize street lining trees to purify polluted air, a research to realize purification of hard-to-degrade substances by introducing degradable genes of microorganisms, and a research intended to create plants that accumulate in them heavy metals densely. (NEDO)

FY 2000 report on the results of the research study of environmental information network; 2000 nendo kankyo joho network ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research study on environmental information network formation. The Internet is experiencing an explosive increase in volume of information distributed therethrough. This is accompanied by increased problems related to information searches, information exchange security and information-reliability guarantees. First in demand are excellent portal sites, and second are sites that can be relied on to responsibly provide information. Cooperation with the real world off the Net is of particular importance, because the operating organizations, e.g., sites, will lose their raison deter, unless they clarify their unique abilities and characteristics under the tendencies towards broadened bands and ubiquity. The public sector, on the other hand, is highly reliable, accumulates a large volume of information, and has high network capacity. It has various functions, e.g., supporting the activities pertaining to ISO standards, and promoting the activities, e.g., those for educational programs, interdisciplinary exchanges by researchers, and matching of various organizations. The international cooperation for environmental information needs construction and operation of the networks, and construction of the infrastructures in the developing countries. If information becomes more ubiquitous, a chaotic sea of information will result. NEDO is strongly obliged to serve as the beacon, because it has established a huge volume of environment-related technologies, information, and networks. (NEDO)

Evaluation report on research and development of an ultra-advanced processing system. 3; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

This paper describes comprehensive evaluation on the following technologies as the ultra-advanced processing system: (1) large output excimer laser, (2) high-density ion beam, (3) an ultra-precision machining device, (4) ultra-advanced processing, (5) measurement and evaluation, and (6) comprehensive test. In the item (1), research and development was performed on such technologies as output increasing, output stabilization and beam formation, having achieved the targets. In the item (2), research and development was performed on such technologies as beam convergence, plasma control, ion transportation, high-frequency quadruple pole acceleration, and large-capacity class ion beam, having achieved the targets. In the item (3), research and development was performed on form creation and ultra-precision machining, having achieved the targets. In the item (4), research and development was performed on formation of high function thin films to apply the laser abrasion process to large area, ion surface modification, wide band area optics, high reflectance optics, ion injection, dynamic mixing, and modification of ultra high-grade metal surface, having achieved the targets. In the item (5), research and development was performed on high-accuracy roughness measurement, shape measurement, optical property evaluation, a wavelength meter, ultra advanced processing standard measurement, and environment correction technology, having achieved the targets. In the item (6), comprehensive demonstration was carried out on the component technologies. (NEDO)

Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

Survey on the scrap iron and steel recycling in Thailand and Indonesia; Hatten tojokoku (Tai Indonesia) ni okeru tetsu scrap saiseiyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes the survey results of the scrap iron and steel recycling industries in Thailand and Indonesia. The purpose of this survey is to extract problems obstructing the scrap iron and steel recycling, to recognize the present situation and predict the future situation, and to examine the possibility of international cooperation. As a result of the survey, it was found that the quality of scrap collected in the domestic market is poor as it contains too many impurities for it to be utilized for the manufacture of many higher quality iron and steel products. The actual quantity of domestically collected scrap is too low to support the expected growth in demand in each nation. Current environmental management practices are largely concerned with the construction of wastewater treatment facilities and the extraction of furnace dust. However, the lack of enforcement of environmental regulations does not encourage companies to implement sound environmental practices. Neither government actively promotes and investigates iron and steel recycling in the domestic, commercial or industrial sectors. Collaboration with overseas nations having more advanced iron and steel industries could be helpful to the scrap recycling industry in both nations. 6 figs., 21 tabs.

Study on soot particle formation and oxidation in DI diesel engine; Chokufunshiki diesel kikan ni okeru susu ryushi no seicho sanka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kurata, K; Senda, J; Fujimoto, H [Doshisha University, Kyoto (Japan); Asai, G [Yanmar Diesel Engine Co. Ltd., Osaka (Japan)

1997-10-01

To clarify soot formation and oxidation process in diesel combustion, the natural emission of OH radical and the flame temperature were obtained in the combustion chamber of D.I. diesel engine. Further, soot were detected by LII (Laser Induced Incandescence) and LIS (Laser Induced Scattering) technique to assess the relative soot diameter and its number density. OH emission and flame temperature were compared with data of soot diameter and number- density. The results show that : (1) OH emission has relation to flame temperature. (2) OH emission arises latter than soot emission, because early soot at early combustion consume OH to oxidate. (3) As soon as it is ignited, soot particles are formed in the region of low temperature. 6 refs., 7 figs., 2 tabs.

Report on a survey in fiscal 1999. Survey on movements in technologies related to phytoremediation; 1999 nendo phytoremediation ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey is intended to discuss the status quo in movements of technologies related to phytoremediation (PM) that utilizes metabolic functions of plants, the overseas situation thereof where the PM application has advanced, and the future technological problems. The PM can be divided largely into the following four categories according to the actions of plants: 1) phyto-extraction - absorbs substances dissolved in water directly or through actions of leguminous bacteria to purify the water or soil; 2) phyto-transformation - action to absorb polluting substances into plant bodies and decompose them; 3) phyto-stimulation - rhizospheric microorganisms are activated by enzymes secreted from roots to decompose chemical substances; and 4) phyto-stabilization - actions to fix or stabilize polluting chemical substances by actions of substances secreted from plants and/or leguminous bacteria in soil and interactions with soil particles. Japan's independent researches have derived such researches as a research to utilize street lining trees to purify polluted air, a research to realize purification of hard-to-degrade substances by introducing degradable genes of microorganisms, and a research intended to create plants that accumulate in them heavy metals densely. (NEDO)

Study on the detached house plan using of a maximum natural energy. Part 1; Shizen energy fukugo riyo no keikaku ni kansuru kenkyu. 1

Energy Technology Data Exchange (ETDEWEB)

Wada, I; Mino, M; Miyata, T; Okawa, M [Nihon University, Tokyo (Japan)

1996-10-27

The geographical position or environment is set on the assumption that the natural energy of a detached house is used in a hybrid state. Moreover, the energy consumption of the house and the natural energy supply obtained from the geographical position were compared and investigated. As a result, the energy consumption is 10,617 kWh, and the energy supply is 8,236 kWh. About 78% of the whole consumption can be theoretically made from natural energy. The energy supply is calculated on the low side during prediction. Therefore, an increase in the energy supply is expected by installing a solar collector based on solar energy, expanding the solar panel area, and increasing the number of wind mills. However, this energy is partially lost via an inverter while it is supplied to the general domestic equipment. At the six main points in Tokyo and its districts, the adaptability of natural energy used based on the regional characteristics is investigated presently and the installation of a system is examined. 13 refs., 2 figs., 6 tabs.

Fiscal 1994 survey report. Survey of environmentally friendly chemical process (Ecochemistry); 1994 nendo kankyo ni yasashii kagaku hanno process (ecochemistry) ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Processes that contain latent environmental problems are the massive generation of wastes (inorganic salt, acid catalyst, base catalyst, and huge quantities of wastewater), handling of dangerous substances (use of hydrogen fluoride, use of phosgene, and use of substances whose discharge is legally controlled), processes which consume much energy (circulation of quantities of raw materials, use of quantities of solvents, separation of products with difficulties, use of high pressure, and multiple stage reaction), and processes which are expected to use resources now remaining unexploited. As an element technology for the solution of problems, there is the development of a solid redox catalyst for liquid phase oxidation. As compared with a liquid phase homogeneous catalyst, it discharges less inorganic wastes, facilitates the separation, recovery, and treatment of inorganic salts, corrodes structural materials less, and is thermally stable. An alkane partial oxidation catalyst when developed will achieve more energy conservation than an alkene oxidation catalyst. In relation to acid/base reaction, the zeolite catalyst will be improved and ultrastrong acids and ultrastrong bases will be developed, and these will reduce wastes, mitigate corrosion, and facilitate product separation. The development of a process is also expected which will avoid the use of toxic phosgene. (NEDO)

Fiscal 1995 research investigation on chemical process technology using supercritical fluid; 1995 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the supercritical fluid utilization technology, conducted in fiscal 1995 were collection of basic data, extraction of R and D subjects and survey/analysis of application fields based on the literature survey and overseas field survey. From the research results, the following were selected as research subjects: as to the clean/recycling process technology, non-selection cascade treatment process of mixed waste plastics, hazardous waste treatment process, and radioactive waste treatment process. As to the unused resource utilization process technology, the supercritical submerged combustion power generation process, heavy hydrocarbon resource reutilization process, biomass synthetic utilization process, and carbon dioxide reutilization process. As to the next generation reaction process technology, the simple reaction process, de-organic solvent process, chemical materialization process for methane, and reaction separation combined process. As the innovative material process technology, the plastic forming process, high-functional materials, high-efficiency energy conversion materials, and heightening of function of solid wastes. 537 refs., 116 figs., 54 tabs.

Research and development cooperation project on environmental measurement using laser radar in fiscal 1995; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of contributing to the environmental management in Indonesia, Japan made R and D of a laser radar to measure the urban air pollution and an environmental network jointly with Indonesia in compliance with the actual situation of the country. At present, in developing countries, air pollution is becoming a big problem because of increases in population and in energy consumption in urban areas according to the industrial/economic growth. As for the laser radar, it is an active sensor with laser as light source and can observe in high resolution the three-dimensional space distribution such as density and composition of air pollutants. Japan is a leader in the development of laser technology which is a core technology for the laser radar and the preceding research. The equipment is installed at several points of urban areas in Indonesia, and at the same time, the observation network is constructed to collect, analyze and process data at the central processing center. This is a 4-year plan from fiscal 1993 to 1996. In fiscal 1995, negotiations with Indonesia and field surveys were conducted to determine sites for installation. A plan for system improvement was also decided on. 38 refs., 24 figs., 14 tabs.

On the estimation method of hydrodynamic forces acting on a huge floating structure; Choogata futai ni hataraku haryoku ryutairyoku no suiteiho ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kagemoto, H.; Fujino, M.; Zhu, T. [The University of Tokyo, Tokyo (Japan)

1996-12-31

A floating structure such as an international airport is anticipated to have a length of about 5,000 m and a width of about 1,000 m. A singular point method may be used as a method to estimate force that such a floating body is subjected to from waves. In order to derive a solution with practically sufficient accuracy, 1250 elements are required in the length direction and 250 elements in the width direction, or a total of 312,500 elements. Calculating this number of elements should use finally a linear equation system handling complex coefficients comprising 312,500 elements, which would require a huge amount of calculation time. This paper proposes a method to derive solution on wave forces acting on a super-large floating structure or fluid force coefficients such as added mass coefficients and decay coefficients at a practically workable calculation amount and still without degrading the accuracy. The structure was assumed to be a box-shaped structure. Strengths of the singular points to be distributed on each element were assumed to be almost constant except for edges in lateral, oblique and longitudinal waves. Under this assumption, the interior of the floating structure excepting its edges was represented by several large elements to have reduced the number of elements. A calculation method proposed based on this conception was verified of its effectiveness. 2 refs., 25 figs., 3 tabs.

Leading research in fiscal 1996. Research study on advanced measurement/analysis technology; 1996 nendo sendo kenkyu. Kodo keisoku bunseki gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For development of production technologies suitable for environment, safety and advanced information-oriented society by improving the flexibility of production lines, some new measurement technologies were researched. Problem solution was attempted by combining the in-situ multi-dimensional measurement technology capable of easily obtaining various 3-D information with the non-contact photon measurement technology superior in operability and sensitivity under any environment conditions. This solution requires a compact radiation source with higher brightness and wider spectral range, and a high-sensitive detector. The technology concentrating photon onto minute regions, high-efficiency transmission, and control technology of photon wave front are also necessary. Development and international standardization of a common interface is unavoidable. In addition, its network is essential for advanced use of multimedia,. In the future, the comfortable life surrounded by advanced products and multimedia, comfortable social environment, safety and resource saving will be achieved by this technology. 94 refs., 75 figs., 15 tabs.

Report on the cooperative study of technology to collect valuable resources in brine; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reported on the research, design, and evaluation on a system to recover by sedimentation magnesium from the brine in the salt manufacture by solar evaporation in Mexico, and a system to recover by adsorbent lithium, boron, etc. from the brine of the solar pond salt field in China. In the case of Mexico, an overall recovery system was developed, but in the evaluation of economy of the system, it cannot be said that the system is feasible even if assuming that the required fresh water can be secured. It was found out that the economical efficiency largely depends upon the cost of hydrated lime and the selling price of magnesia clinker. In the case of China, a plant for production of 500 tons/year of lithium carbonate was conceptually designed to evaluate the economical efficiency. As a result, the internal profitability of the plant is not so high, approximately 6%, though continuously profitable during the operation of 15 years. It was indicated that the project was not economically very efficient. 164 figs., 44 tabs.

FY 1974 Report on results of Sunshine Project. Feasibility study on digging high-temperature beds; 1974 nendo koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-31

The desired target geothermal conditions for which the digging equipment is to be developed are 3,000 to 5,000 m as depth, 400 degrees C as temperature and 500 kg/cm{sup 2} as pressure. As the first phase, the study is conducted on feasibility of development of techniques for digging high-temperature beds under a temperature condition of 250 degrees C, where the rotary table type digger is mainly studied. It is most widely used for digging oil wells as well as geothermal wells. The current rotary table B type digger is studied as the equipment serviceable at 250 degrees C as the target temperature level for the moment for digging high-temperature beds. The studied items include the problems involved in the digger body, pipes, bits and other members, and also measures to expand its possibility. Also studied/surveyed are applicability of the new digging techniques now under development to geothermal wells, and techniques for fracturing high-temperature rocks. This report summarizes to help select the methods desired to be developed in the future, and plan development of the digging systems. (NEDO)

Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Funaki, T; Hayashi, S [Osaka University, Osaka (Japan). Faculty of engineering

1997-12-31

It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

Achievement report on research and development in the Sunshine Project in fiscal 1976. Comprehensive discussion on a hydrogen utilizing subsystem and research on peripheral technologies (Research on peripheral technologies for hydrogen); 1976 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This paper describes research on peripheral technologies for hydrogen. For the cost of manufacturing hydrogen from different primary energies, coal gasification could be the lowest at the present time. In the nuclear power field, the thermo-chemical method and the water electrolysing method may be assumed, but they depend greatly on future technological development. Particularly the water electrolysing method is dependent on electric power cost. In the hybrid method, hydrogen is obtained from electrolysing reaction with water of sulfur dioxide derived by paralyzing sulfuric acid (oxygen is also generated). The method requires two forms of energies, heat and electric power, whereas combination with a very high temperature reactor (VHTR) is being discussed as a heat source. This method may not be said greatly more advantageous than the direct water electrolysis, but may have future possibility. Hydrogen manufacturing utilizing living organisms is an interesting matter in terms of science and engineering, with a large number of research achievements beginning to appear. Expectation is drawn on the mechanism based on co-work of photosynthesis and a hydrogen generation system, alga and bacterium strain search, separation, cultivation, and applied research and development. Research is also under way to obtain hydrogen by converting photo-energy by using an electrochemical photo-cell utilizing semiconductor electrode to electrolyse water (color sensitizing) (NEDO)

Fiscal 2000 survey on electrical power supply system for the purpose of reducing greenhouse effect gas. Three scenarios for spread of distributed power generation by 2010; 2000 nendo onshitsu koka gas sakugen no tame no denryoku kyokyu system ni kansuru chosa hokokusho. 2010 nen made no bunsangata dengen fukyu ni kansuru mittsu no scenario

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An examination was conducted concerning the course of spread of distributed power generation (on-site power generation of 2,000 kW or less) by the year 2010, with three scenarios prepared. In the scenario 1, the government will completely deregulates the power market and take no other steps, leaving the matter to market competition. The universal service will be abandoned, which means higher power prices for remote regions, contributing to the spread of home power generation. In the scenario 2, the government, having reached the limits of the nuclear propulsion policy, will adopt natural gas as the center of its electrical power policy, providing preferential treatments such as subsidies and tax exemptions and requesting the power companies to increase their usage. This will lead to higher transmission charges, with distributed power generation more advantageous to the IPPs in terms of cost. In the scenario 3, environmental awareness will make increase in the capacity quite difficult including power generation facilities and transmission/distribution network, and will invite a power crisis in the long run through insufficient capacity in power generation and transmission/distribution volume. Distributed power generation requiring no reinforcement to the grid will spread such as household-use type without system interconnection, solar cells or small fuel cells. (NEDO)

FY 1998 report on the results of the technology development on the integration of nerve information; 1998 nendo shinkei joho togo ni kansuru gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This R and D aims at developing the interface system including 2D multipoint high density electrode elements which measure and analyze the information processing process of cranial nerves at high speed and in minute detail. The R and D were carried out on the following 4 subjects: 1) development of 2D high density multipoint electrode; 2) development of alignment/bonding technology; 3) development of technology for existence maintenance/activation of nerve cells; 4) study of performance evaluation and applicability of the system. In 1), an electrode is developed in which the high density multipoint platinum electrode was built on glass substrate, and the following are conducted: making a pattern of alignment of this electrode, making the shape of electrode 3D, and technical development of surface composition. In 2), the following are developed: technology to align cells on the patterned electrode element correctly and technology to bond cells on the element for a long time. In 3), the following are developed: functional materials to hold living nerve cells/nerve systems on the electrode element for a long time, nutrition system, and technology to monitor the state of cells/systems on the substrate. In 4), conducted are the evaluation of performance of the developmental system and the applicability to the screening in nervous function molecular search, etc. (NEDO)

Report on evaluation concerning R and D of magneto hydrodynamic (MHD) generation. Introduction; Denji ryutai (MHD) hatsuden no kenkyu kaihatsu ni kansuru hyoka hokokusho. Soron

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

Evaluation was conducted concerning R and D on magneto hydrodynamic (MHD) generation, with proposals made for the future R and D. As a result of the experimental operation and studies of the Mark 7 machine for MHD generation, a cold wall type generation channel was found promising in the long-term durability under MHD generation conditions. In addition, R and D was conducted on the exhaust gas control system that fulfilled an environmental standard, seed recovery method, grasp of seed coagulation state, etc. The R and D on element technologies were carried out along with the R and D of the Mark 7 and played a role in the backup of its experiment. MHD generation presents a large number of attractive characteristics, with its development expected in the future. However, it seems too early to immediately move on to the next step. Examinations should be made on such matters as comparisons with various kinds of new power generation systems using coal, trends in foreign countries particularly the U-500 project of the Soviet Union, the ideal system for more efficient development, and possibility of international cooperation. (NEDO)

Report for fiscal 2001 investigations on energy saving assistance institutions in different countries; 2001 nendo kakkoku no sho energy shien seido ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Taking up China, India, Indonesia and Thailand as the object, investigations were performed on political financing measures that can be used for installing energy saving facilities, and on applicable preferential taxation systems that are applied in each country. Indonesia has no aid measures such as subsidies and political financing directly purposed for energy conservation. Import duty exemption is applied for the purpose of promoting investments. Three kinds of funds are available through IFCT to implement fund aid to protect the environment. Energy saving fund has been established as an energy saving policy to provide subsidies. Energy saving machineries recognized by the investment committee are exempted from the import duties. India has no political financing measures directly purposed for energy conservation. Its preferential taxation system for energy conservation includes the 100% accelerated amortization system for energy saving machineries and facilities, and the preferential import duty system. In China, the financing from the China National Development Bank is considered utilizable in installing energy saving facilities. The country has no aid measures in the taxation system, but fund aid and subsidy by supplementing interest are provided. (NEDO)

Study on low permeable backfill materials. Backfill materials for waste disposal facilities; Koshisuisei juten zairyo ni kansuru kenkyu. Hoshasei haikibutsu shobun shisetsu eno tekiyosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, F; Konishi, M; Shiraishi, H [Okumura Corp., Osaka (Japan)

1994-11-15

A discussion was given on the fundamental properties of mortar made from cement mixed with silica fume. Four kinds of silica fumes with different particle size distributions were used. The following results were obtained: distribution of pores in mortar admixed with silica fume shifts to the smaller radius side; while the admixture increases the compression strength in mortar, the increasing trend varies depending on the kinds of silica fumes; this is thought to be caused from the difference in pozzolan activity between silica fumes; and the strength increase is caused by densification of the structure due to the pozzolan reaction that is generated after hydration, or in other words, decrease in the pore volume. The applicability of the mortar was investigated as a filling mortar to fill up clearances between wastes. It was found that the filling performance can be controlled by mixing silica fume at an adequate level and adjusting the viscosity. The diffusion coefficient for the admixed concrete is smaller by 30% to one digit than that for the ordinary concrete. High-performance water stopping concrete of 0.11 {times} 10{sup 4}cm {sup 2}/s at maximum was obtained. The concrete can be regarded as a material having superb filling and water stopping performances. 6 refs., 4 figs., 5 tabs.

Research report on the trend of preventive measures against global warming by substituting CFCs; Daitai freon no chiku ondanka taisaku doko ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper reports the research results on the present state and future trend of protective measures for the ozone layer, and the trend of preventive measures against global warming by substituting CFCs such as HFC, through international conferences, meetings and lecture meetings, and literature survey. In the 8th meeting of the parties to the Montreal Protocol, it was presented that refrigerator producers in Thailand phased out CFCs from their products earlier than the schedule in cooperation with Japan. The final draft including the approval of essential use from 1997 to 2002 was reviewed, and reported to the technology/economy assessment panel. Reduction of ozone depleting substances was guided in Thailand, Indonesia and Philippines. The latest trend of substituting technologies of HCFC was surveyed, and the control trend of F-containing greenhouse effect gas emission was also surveyed through the conference of the parties of climate change in fiscal 1996. Based on the IPCC report in 1995, the emission amount of greenhouse gases of nearly 10% in contribution such as CO2, methane and fluorocarbon was arranged. R and D on destruction of CFCs was also surveyed. 35 refs., 54 figs., 32 tabs.

Basic survey on the residence using hybrid energy in snowy cold regions; Sekisetsu kanreichi ni okeru hybrid energy katsuyogata jutaku nado ni kansuru kiso chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The conceptual model and feasibility of the hybrid energy system for residences and public facilities in snowy cold regions were studied. Based on the existing data, the existing and available amounts of natural energy and unused energy in the target area, Sapporo were estimated. Based on the predicted energy demands of 4 kinds of building models, the energy systems for such models were studied. The use of the following energies was considered: photovoltaic power generation and solar heat for all the models, household sewage energy for the multiple-dwelling house model, and wind power generation for the public facility model. The annual energy balance was calculated to evaluate it. The use of additional commercial electricity was necessary, while surplus solar heat energy was found in summer which can push up the self-sufficiency rates of the residence and public facility models to 70% and 44%, respectively. The multiple- dwelling house model which can use a large amount of household sewage energy could utilize 80% of new energy, while the other 3 models utilized only 60-70% of that. 81 figs., 42 tabs.

FY 1997 survey report on information sharing product life-cycle systems. 2; 1997 nendo joho kyoyugata product life cycle system ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Highly value-added products considering a total life-cycle of products by integrating both production and consumption activities are much in demand, and each information corresponding to each product should be realized by concept integrating both information and product as common element. Survey was made on what a social system integrating production and consumption should be, a product information model, and technology integrating both information and product for raw material, industrial machine and household appliance as examples. An information model shared by the whole production and consumption activities was first prepared. Based on this model, data storage, update, retrieval and dispatch technologies were surveyed and developed for life-cycle systems. Degradation and life sensing technology was surveyed for maintenance, repair and disposal activities using proper unstable information of each product. A support system for use of shared information was developed to promote a new highly value-added function. Total evaluation was made on information sharing product life-cycle systems. 10 refs., 23 figs., 7 tabs.

Properties of board made from wood powder with phenol-formaldehyde-powder resin; Mokufun wo genryo to shita board no seizo to zaishitsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, S.; Yamada, M. [Shizuoka Univ., Shizuoka (Japan). Faculty of Agriculture

1998-04-15

The purpose of this study is to acquire fundamental knowledge about the factors for production and the physical properties of boards when wood powder is used as the main material and powder adhesive is used as the binder in the formation of wood boards under heat and pressure. The effects of temperature for pressing, specific gravity of board, and the ratio of adhesive on bending strength, internal binding force, and size and stability against moisture are investigated. The temperature behavior at the central area of boards under heat and pressure shows similar tendency of stagnation near 140degC which increases thereafter irrespective of the temperature of the hot plate in this experiment. The bending property increases linearly when the resin content is low, and shows the tendency of leveling off gradually when the resin content is larger than 20%. Linear relation with specific gravity if obtained in the 0.6 to 1.0 specific gravity range. Wood powder boards have high internal size stability in the thickness direction than ordinary wood boards. 13 refs., 11 figs.

Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

Energy Technology Data Exchange (ETDEWEB)

Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering

1996-05-01

This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

Fiscal 1999 survey report. Basic survey on practical application of innovative energy technologies; 1999 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This survey aims to verify whether recoverable energies can bear the important role of energy source in place of fossil fuels, to probe into problems that may arise in the process of recoverable energy introduction, and to compile suggestions about measures toward their smooth introduction, these by working out an 'ultralong-term world energy supply and demand outlook' valid up to 2100. Various measures to deal with global warming are analyzed by simulation. The study is not to predict what is in store but to metrically describe and present choices and possibilities for the future with a theoretical consistency based on various factors including economic growth, population, demand for energy, magnitude of fossil energy resources, and feasibility and cost of recoverable energies. This study implies that there is not a single, determining policy for solving the global warming problem and that it is important to cope with the problem by resorting to combinations of various means. (NEDO)

Fiscal 1996 investigational research on the chemical process technology using supercritical fluids; 1996 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Importance was studied of making a research on the chemical process technology using the supercritical fluid. As for its effect on global warming, the amount of CO2 emission was compared during the operation between the conventional process and the process using the supercritical fluid, the CO2 reduction rate and amount were trially calculated, and a CO2 reduction of a several ten thousand ton scale in carbon conversion was predicted. As to hazardous materials and the reaction of waste retrieval, it was made clear that the process using the supercritical fluid was valid also for objects for which the chemical process used to be impossible, which indicates a possibility of the widening field of application. Concerning its effect on the energy conservation, energy reduction of several ten thousand tons in heavy oil conversion was predicted by replacing all the existing processes with supercritical fluids. Relating to the recycling, with the use of supercritical fluids, the process is possible which produces higher quality and yield and fewer unnecessary products such as char than the conventional process. 197 refs., 102 figs., 71 tabs.

Investigational report on international joint research in medical/walfare appliances in fiscal 1993; 1993 nendo iryo fukushi kiki kokusai kyodo kenkyu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The field of concrete cooperation, method of R and D, and business, environment to support the project, and system to promote the project were studied for the research under international cooperation through investigating the trend and organization of R and D of the medical/welfare appliances at home and abroad. Projects were then proposed. In the project for collecting/analyzing the trace quantity of blood, the anomaly is inspected at a molecular level from the collected trace quantity of blood to make the biochemical inspection painless for the patients suffering from infectious symptom or disease of adults. In the project for the high-accuracy and high-function measurement without invading the diseased part of living body, the configuration and metabolic function are measured by nuclear magnetic resonance to early detect the symptom of Alzheimer and other different obstinate diseases. In the operation support system project with three-dimensional images of living body, the three-dimensional information is obtained, by X-ray CT or MRI, about the diseased part of living tissue. Upon the exact determination of its location, the disease is cured. Besides, the monitoring systemproject was proposed for the old people`s safety against dementia. The human care robot project was also done. 56 refs., 11 figs., 15 tabs.

Fundamental study on the melting process of crushed ice in a heat storage container; Chikunetsu sonai ni takuwaeta saihyo no yukai ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yanadori, M; Kobori, H [Hitachi, Ltd., Tokyo (Japan); Tsubota, Y [Tokyo Electric Power Co. Inc., Tokyo (Japan)

1998-03-25

This report deals with heat transfer in the melting process of crushed ice filling in a ice/water heat storage container. Volumetric heat transfer rate and melting end-time are measured when rectangular-type, small-stone-type and particle-type ice in the container are melted by circulation hot water. Melting end-time of small-stone-type ice is the shortest and that of particle-type ice is the latest. Volumetric heat transfer rate of small-stone-type ice and rectangular-type ice is larger than that of particle-type ice. The flow rate of circulation hot water throwing in container through a inlet pipe influences remarkably on heat transfer rate. 4 refs., 10 figs.

Report on investigations and studies on development of materials for hydrogen absorbing alloys; Suiso kyuzo gokin no zairyo no kaihatsu ni kansuru chosa kenkyu hokokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper describes investigations and studies on hydrogen absorbing alloy materials and the technologies to utilize them. In the investigations and studies, literatures were collected and put into order, questionnaire surveys were performed and analyzed, lecture meetings and panel discussions were held, and the discussion results were summarized. In the present status of developing hydrogen absorbing alloys, the current status of and problems in developing such hydrogen absorbing alloys as Ti-based, Mg-based, and rare earth-based alloys were put into order. Discussions were given on prospects of possibilities of developing new alloys, making them amorphous, and putting them into mass production. In the current status of developing the utilizing technologies, such technologies as hydrogen storage systems and heat pumps were put into order and discussed. With regard to problems in hydrogen absorbing alloys, discussions were given on alloy weight, pulverization, activation, heat conductivity, and alloy costs. In discussing the safety, discussions were given on the safety and compliance with related laws and regulations relative to hydrogen transportation using a great amount of hydrogen absorbing alloys, their storage, and heat storage systems. In addition, questionnaire surveys were carried out with an objective to identify the status of developing hydrogen absorbing alloys and needs from the industries. (NEDO)

Research cooperation in the development of laser radar for environmental measurements. Environmental network; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku. Kankyo network

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Among the research cooperation in the development of laser radar for environmental measurements with Indonesia between FY 1993 and FY 1996, results of the research and development of the environmental network are summarized. For the environmental information network, the Tokyo NOC is linked as an Internet connection point in Japan with the Jakarta NOC using an international dedicated line with a capacity of 64 Kbps. The Tokyo NOC is linked with domestic environmental information researchers using Internet. Thus, data stored in the data processing system of laser radar can be exchanged, information in both countries can be exchanged using E-mail, and data can be accumulated. For the research cooperation with Indonesia, research of path control and information relay server, research of effective transmission of data on the network, and research of multimedia communication have been conducted. The multimedia communication, distributed processing, and extension of dedicated line network using PPTP have been also conducted. 39 figs., 4 tabs.

Survey on the technological development issues for large-scale methanol engine power generation plant; Ogata methanol engine hatsuden plant ni kansuru gijutsu kaihatsu kadai chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Based on the result of `Survey on the feasibility of large-scale methanol engine power generation plant` in fiscal 1992, concrete technological development issues were studied for its practical use, and the technological R & D scheme was prepared for large-scale methanol engine power plant featured by low NOx and high efficiency. Technological development issues of this plant were as follows: improvement of thermal efficiency, reduction of NOx emission, improvement of the reliability and durability of ignition and fuel injection systems, and reduction of vibration. As the economical effect of the technological development, the profitability of NOx control measures was compared between this methanol engine and conventional heavy oil diesel engines or gas engines. As a result, this engine was more economical than conventional engines. It was suggested that development of the equipment will be completed in nearly 4 years through every component study, single-cylinder model experiment and real engine test. 21 refs., 43 figs., 19 tabs.

Report on the surveys in fiscal 1999. Surveys on practical application of the research achievements; 1999 nendo kenkyu seika no jitsuyoka ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A number of technological hurdles exist in the process of practically applying the fundamental researches, wherein risks for private business entities to promote the technological development are not at all small. The present surveys are intended to elucidate the actual status as to how a practical application process for technologies is positioned in the series of research and technological development activity floats by private corporations, and what kinds of problems are present, to serve for discussing the way the future supportive environment improvement should be. The 'practical application processes' in private corporations were put into order and analyzed, using as the base the existing study results relative to technological innovation mechanisms. Investigations ere performed on the existing Japanese research and technological development supporting institutions for the practical application processes employed by the private corporations. The result was used for reference of discussing the problems therein. Furthermore, it is indicated that, in the R and D strategies in the U.S.A., profitability is placed as the largest target by means of strengthening the linkage between research and commercialization. This has resulted in decline in the fundamental researches, for which discussions are developed currently. This paper reports investigations on the actual status of business enterprises in the practical application processes. (NEDO)

Feasibility design of a floating airport and estimation of environmental forces on it; Futaishiki kuko no sekkei to kankyo gairyoku no suitei ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Inoue, Y.; Tabeta, S.; Takei, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

1996-12-31

A rough design was performed on a floating airport. On this floating structure, environmental external force was estimated, mooring design was carried out, and discussions was given on the position retaining performance important for airport functions and behavior of the floating structure. The discussion was given on cases that the airport is surrounded and not surrounded by floating breakwaters. A floating structure which becomes super-large in size requires considerations on force due to sea level gradient as a result of a tide. Deriving flow condition changes and force acting on the floating structure simultaneously by using numerical calculations makes it possible to estimate current force given with considerations on influence of the flow conditions created by installing the floating airport. Estimation was carried out by using a zone dividing method on wave drifting force acting upon the floating airport. As a result, it was found that installing floating and permeating type breakwaters can reduce the wave drifting force acting on the floating airport. The wave drifting force working on the floating airport can be reduced by installing the floating and permeating type breakwaters to lower levels than when no such breakwaters are installed. The airport may be moored with less number of fenders when the fenders of the same type are used. 18 refs., 10 figs., 5 tabs.

FY 2000 report on the survey of energy conservation technology in Japan; 2000 nendo chosa hokoku. Nihon kokunai no sho energy gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting self-help efforts to deal with energy environmental problems in developing countries in the Asian region, etc. and making the transfer of the energy conservation technology and petroleum substituting energy technology that are at a practical stage and are owned by Japan, evaluation of each technology was conducted in terms mainly of applicability for a model project. The existing survey data were supplemented/deleted. As the model project supposing the application to developing countries in Asia, types of industry for survey were selected as follows: iron/steel, nonferrous metal, chemical industry, oil refining, ceramics/earthware, paper/pulp, foodstuffs, textile/spinning, electricity (power generation)/gas, technologies common to all industry types. Technologies for survey were energy saving production facilities and energy saving equipment at plant with a regular scale to which the applicability as the model project was supposed. The energy saving effect was all calculated in TOE, and the method to calculate the effect was also described. The paper further described possibilities of introduction/spread of the said technologies to developing countries in Asia, introduction limitation/preconditions, cost vs. effect, etc. (NEDO)

Evaluation report on research and development of an ultra-advanced processing system. Summary edition; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

Research, development and evaluation were performed with an objective of establishing the basic processing technology and ultra-precision machining device technology utilizing large output excimer laser and high density ion beams. With regard to the large output excimer laser technology, the short wavelength excimer laser life extension technology has demonstrated ong-life operation of 1.02 times 10{sup 9} shots exceeding the final target at the initial laser output of 105 mJ/pulse. With respect to the high-density ion beam technology, the gas phase converged ion beam technology has achieved an ionic current density of 2.5 {mu}A/sr. and a beam current of 25 pA. Regarding the ultra-precision machining device technology, a large ultra-precision grinding machine of five shaft control type was developed as a final target demonstrating machine, which exhibited the shape accuracy of 0.7 {mu}m and surface roughness of 3.45nm. The surface roughness satisfied the final target. Other activities include studies on the ultra-advanced processing technology, measurement and evaluation technology, comprehensive tests, and practical application of the technologies, having derived respective achievements. (NEDO)

Study on property-gradient polymer electrolyte for rechargeable lithium batteries; Lithium niji denchi no tame no keisha tokusei kobunshi denkaishitsu no sosei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kokumi, Z; Kanemura, S; Inaba, M; Takehara, Z; Yao, K; Uchimoto, Y [Kyoto University, Kyoto (Japan)

1997-02-01

This paper describes the fundamental experiments for creating property-gradient polymer electrolyte for rechargeable lithium batteries. The rechargeable lithium battery is composed of an anodic composite agent section with high ion conductivity, a separator equivalent section with high mechanical strength (high bridging degree), and a section surpressing the precipitation of metal lithium by contacting with it. The continuous property-gradient polymer electrolyte was tried to be synthesized by means of the plasma polymerization method. As a result, plasma polymerization electrolyte with high ion conductivity could be prepared from the liquid phase by using a monomer with low vapor pressure. Porous material simulating the anodic composite agent was impregnated by the monomer, which was plasma-polymerized. As a result, it was found that the bridging degree decreased from the surface towards the inside of the plasma-polymerized porous material. In addition, polymer was prepared using fluorine-base monomer. Thus, LiF thin film could be prepared through the reaction between the polymer and metal lithium. 3 figs.

Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ishida, S; Suzuki, T; Yamamoto, M [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

1997-02-01

This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

Study of shift shock reduction of an automatic transmission using robust control; Robust seigyo wo mochiita ido hensokuki no hensoku shock teigen ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Oshima, K [JATCO Corp., Shizuoka (Japan); Totsuka, H; Sanada, K; Kitagawa, A [Tokyo Institute of Technology, Tokyo (Japan)

1997-10-01

To effectively reduce shift shock of an Automatic Transmission, we designed a feed-back controller that manipulates the hydraulic pressure of a clutch and input torque, and also controls the turbine revolution and output torque. We used robust control theory to consider the fluctuation of hydraulic characteristics and friction elements, and verified the effect of the controller by simulation and experiment. 1 ref., 11 figs.

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Investigational study on the hydrogen production method by the quinone method); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kinonho ni yoru suiso seizoho ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the hydrogen production from water by means of quinone compounds. The paper studied a preparation method in case of using n-TiO2 photosemiconductor and p-GaAs and Gap photosemiconductor to photoelectrode as catalysts of this reaction. The reaction from p-benzoquinone to p-hydroquinone by reaction with H2O were studied in terms of photochemical reaction, and light reaction/dark reaction of photosemiconductor electrode. As a result, it was found out that this reaction easily advances by the photochemical reaction by solar light, and also that it advances by the counter electrode Pt electrode reaction in the water electrolysis of n-TiO2 photosemiconductor electrode. The H2 production reaction from p-hydrogquinone was studied in terms of the photochemical reaction, photosemiconductor electrode reaction, and effects of the catalysis of electron transport of metal salts, methylviologen, etc. As a result, in the n-TiO2 photosemiconductor electrode reaction, H2 formation was not as great as it can be confirmed. However, it was found that p-hydroquinone can produce H2 under the existence of methylviologen or Fe salts. (NEDO)

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Survey of research management technique to contribute to formulation of long-term energy strategy); 2000 nendo choki energy gijutsu senryaku ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (choki energy senryaku sakutei nado ni kansuru kenkyu kanri shuho no chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of acquiring research management related basic materials necessary in the study of long-term energy strategy, a survey is conducted of the history, theory, and techniques of research management, the state of its utilization, and the products. The results of the survey are compiled into an introduction, itemized discussion, and materials. In the introduction, the purpose and basics of research management are discussed and confirmed. Taken up in the itemized discussion are an item (1) on research management relating to the selection of themes for research and development, which discusses the formulation of research and development strategy, selection of themes for research and development, formulation of plans for them, and a theme selection assisting system, an item (2) on research management relating to the management of research implementation, which discusses the management of implementation of research and development, interim assessment, and an implementation management assisting system, and an item (3) on the studies of key points for implementation and of research management for NEDO (New Energy and Industrial Technology Development Organization) to practice. As for the materials, they comprise commentaries on theories and techniques, an ex post facto assessment system and instances of assessment, list of persons related to research management, and commentaries on reference materials. (NEDO)

FY 1998 annual summary report on shared product life-cycle total information system. 3; 1998 nendo joho kyoyugata product lifecycle system ni kansuru chosa hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Recycling resources is gaining importance increasingly to correspond to global environmental problems. In urban areas, in particular, it is important to efficiently recover and recycle used large-size consumer products, e.g., home electric appliances and automobiles, which are discharged in large quantities. This study proposes a shared product life-cycle total information system, based on recognition that material recycling systems, encompassing stock materials, product production, consumption, and disposal and recycling of wastes, are essential. This system corresponds a material to information, in an attempt to realize more efficient recycling of products. The study for this fiscal year was focused on use of information modules attached to products and their members, product recycling systems using these modules, necessity for and problems involved in thermal recycle systems, problems involved in recycling home electric appliances and extraction of the data for their recycling, and material recycling process systems for home electric appliances and automobiles. (NEDO)

FY 2000 Study report on the study on trends of the technologies related to climate change; 2000 nendo kiko hendo ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project is aimed at construction of the system which can provide information after searching in realtime key words in a vast volume of reports by Intergovernment Panel on climate Change (IPCC) and answers to Policy Relevant Questions (PRQ). The technical terms appearing in scientific documents use few synonyms to avoid ambiguity, and analysis of frequency of keywords is expected to be an index which provides important information. The chapters in the IPCC reports are not independent but coordinated with each other. It is therefore considered that analysis of the inter-chapter structures based on the keyword frequency analysis provides the meaningful viewpoints for, e.g., understanding Third Accessment Report (TAR) and extraction of the future research themes. For analysis of the logical structures of the sentences containing the keywords, special attention is focused on the term (sustainability) as the most important keyword in TARs, and its logical structures are analyzed. It is decided that the answers to PRQ are extracted from TOD. (NEDO)

Global environmental benefits of industrial heat pumps (fiscal 1993); 1993 nendo koon heat pumping gijutsu ni yoru chikyu ondanka keigen koka ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

An investigational study was conducted aiming at making a quantitative grasp of effects of the spread of industrial heat pumps on energy conservation and greenhouse gas reduction and at promoting the spread. Finally, the following eight countries joined this international joint research: Canada, France, Japan, Holland, Norway, Sweden, the U.K. and the U.S. Each country share the work and expenses for the research with each other. Japan made investigational researches on the application of heat pumps to processes of the chemical industry, oil refining industry, food industry, paper/pulp industry, and dyeing/weaving industry, and on the effects of greenhouse gas reduction. As procedures taken, values up to 2010 were estimated of energy prices in each country, energy supply/demand, rates of the heat source configuration for electric power supply, etc., the heat flow of the above-mentioned process was made clear, and analyses were conducted of annual profits, energy consumption, and depreciation period in the case of adopting heat pumps. Moreover, the energy conservation amount and greenhouse effect gas reduction amount were estimated based on the result of the analyses. 69 figs., 196 tabs.

Study of the influence of microgravity on the biological cells and molecular level; Seitai saibo bunshi level ni okeru bisho juryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The shape of osteoblast, gene appearance, gene of rice blast, cellular fusion of plants, gravity acceptance mechanism of unicellular organisms, and physiological and immunity functions of mice were investigated under the microgravity condition. The influence of gravity on the vital reaction and the influence of microgravity on the crystallization of vital substances were also investigated. For the observation of osteoblast, the fluorescence dye reacted with Ca was well taken in the cells. The microgravity affected the stability of rice blast, but hardly affected the protoplast culture of mushroom. The reaction of ciliate against the gravity related to the specific gravity difference between cells and outer liquid. The level of adrenaline in blood of mice increased during the drop. The moving speed of trigger waves of chemical parallel slit formed at the BZ reaction under the microgravity became 60% to 80% of that on the ground. In the case of crystallization at the deposition agent concentration of 1% to 4%, the turbidity showing the degree of crystallization changed complicatedly. Nine processes of crystal growth were recognized. 21 refs., 55 figs., 1 tab.

Fiscal 1994 survey report. Survey of recent trends in CFC phaseout measures overseas; 1994 nendo shogaikoku ni okeru freon taisaku saishin doko ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Technical literature is referred to for the survey of recent trends in CFC (chlorofluorocarbon) phaseout in various countries overseas. The European Union will totally abolish CFC by the end of 1994 while other developed countries will totally abolish the same by the end of 1995 in compliance with the Montreal protocol. Many of the developing countries are actively striving to reduce CFC use with the help of the Multilateral Fund of Montreal. China and India have production facilities in themselves, and have not announced a phaseout program. There is a proposition for accelerating the regulation of HCFCs (hydrochlorofluorocarbons), but reliable substitutes for them are not yet available and their ozone layer restoring capability if used will be slight. It is feared that such will on the contrary retard CFC phaseout in developing countries. Accordingly, any abrupt acceleration of CFC phaseout implementation is inappropriate. Introduced in this report as fluorine-containing greenhouse gas-related information are a summary of the United Nations Framework Convention on Climate Change and the history of Intergovernmental Panel on Climate Change activities. According to an American survey, the aluminum industry emits 30,000 tons of CF{sub 4} and C{sub 2}F{sub 6}, and the semiconductor manufacturing industry 2,000-3,000 tons. As for SF{sub 6}, 5,000-8,000 tons are emitted mainly by the power industry. Measures for inhibiting them are being taken. (NEDO)

Investigation on the chemically fixing technique of carbon dioxide utilizing solar energy; Taiyo energy riyo ni yoru nisanka tanso no kagakuteki koteika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

This report describes the results of effective fixing technique of CO2 by utilizing solar energy. First of all, the investigation was directed to the technique for synthesizing ethylene, hydrocarbons and alcohol by electrochemical reduction of CO2. The power required for this process is supplied by photovoltaic power generation. Development of excellent electrode catalyst is needed because the reduction of CO2 requires a high overvoltage. It is desirable to enhance the selectivity of the reaction for specific material and improve the transport process in the electrolytic cell. Next, designing of material and reaction of photocatalysts using semiconductor electrode and semiconductor particulate was examined. A semiconductor electrode made of FeS2 is inexpensive and has a high ability of collecting solar light. In the category of photocatalysis system, a photocatalytic system in which semiconductor particles are embedded in vesicle and a photpocatalyst based on potassium niobate are noteworthy. As biosystem, the method of reducing CO2 by calcareous algae which simultaneously advances fixing and calcification of CO2 by photosynthesis is noteworthy. 129 refs., 45 figs., 20 tabs.

Studies on the catalysts for coal liquefaction. ; Rheological studies of coal liquefaction process. Sekitan ekikayo shokubai ni kansuru kenkyu. ; Sekitan ekika process no rheology teki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Muraoka, T; Oda, H; Yokokawa, C [Kansai University, Osaka (Japan). Faculty of Engineering

1991-11-07

Hydrogenolysis of different rank coals as Taiheiyo coal (75.7C%) and Pittston coal (85.4C%) were conducted in the presence of four kinds of catalysts (CuCrO4, Fe2O3+S, MoO3-TiO2 and MoS3-Al2O3) with an addition of tetralin as vehicle. The variation in viscosity in every reaction system was traced in the initial stage of the reaction by a torque meter attached to an autoclave. As a result, in every system, the torque decreased in the initial stage of temperature rise because of reduction of a solvent viscosity. The torque subsequently increased with temperature indicating two peaks before the following gradual decrease. In Taiheiyo coal, both peaks were low, and its coal conversion was more than 85%, while in Pittston coal, both peaks were sharp and high, and both subsequent torque reduction and coal conversion were smaller than those of Taiheiyo coal. 5 refs., 10 figs., 2 tabs.

Investigation of the deposit formation in pipelines connecting liquefaction reactors; 1t/d PSU ni okeru ekika hanno tokan fuchakubutsu no seisei yoin ni kansuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Okada, Y.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

1996-10-28

The liquefaction reaction system of an NEDOL process coal liquefaction 1t/d PSU was opened and checked to investigate the cause of the rise of differential pressure between liquefaction reactors of the PSU. The liquefaction test at a coal concentration of 50 wt% using Tanito Harum coal was conducted, and it was found that the differential pressure between reactors was on the increase. By the two-phase flow pressure loss method, deposition thickness of deposit in pipelines was estimated at 4.4mm at the time of end operation, which agreed with a measuring value obtained from a {gamma} ray. The rise of differential pressure was caused by deposit formation in pipelines connecting reactors. The main component of the deposit is calcite (CaCO3 60-70%) and is the same as the usual one. It is also the same type as the deposit on the reactor wall. Ca in coal ash is concerned with this. To withdraw solid matters deposited in the reactor, there are installed pipelines for the withdrawal at the reactor bottom. The solid matters are regularly purged by reverse gas for prevention of clogging. As the frequency of purge increases, the deposit at the reactor bottom decreases, but the deposit attaches strongly to pipelines connecting reactors. It is presumed that this deposit is what Ca to be discharged out of the system as a form of deposition solid matter naturally in the Ca balance precipitated as calcite in the pipeline connecting the reactor. 3 refs., 5 figs., 4 tabs.

Questionnaire investigation for the earthquake in Honjo city and Yazawa city, Akita Prefecture; Jishin ni kansuru ishiki chosa (Akitaken Honjoshi oyobi Yuzawashi ni okeru anketo kara)

Energy Technology Data Exchange (ETDEWEB)

Nogoshi, M [Akita University, Akita (Japan). College of Education; Kabutoya, S

1996-05-01

Consciousness for the earthquake was investigated by questionnaire surveys made in Honjo City and Yuzawa City, Akita Pref. in October 1995 twelve years after the Nihonkai Chubu Earthquake (M=7.7) in May 1983. The survey was conducted in terms of 27 items including personality, memory, knowledge/interest, psychology/action, mental attitude/preparations, wishes for researchers and administration, etc. Also included were the items on the Great Hanshin-Awaji Earthquake and the earthquake blank areas. The number of distributed questionnaires and the recovery rate of them are 1500 and 79.2% in Honjo City, and 1700 and 84.7% in Yuzawa City. From the survey, it was found that people have a lot of knowledge of and high interest in the earthquake and well remember it, and a lot of people know of tsunami, liquefaction phenomena, and the earthquake blank area. Further, they are afraid of earthquakes and think of their actions to be taken in case of earthquake. However, most people are little prepared for earthquakes. Important future subjects were suggested for the study of disaster prevention measures. 13 figs.

Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

Energy Technology Data Exchange (ETDEWEB)

Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

1997-11-25

In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

Report on a survey in fiscal 1999. Survey on movements in technologies related to climate change; 1999 nendo kiko hendo ni kansuru gijutsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Working group 3 of the Intergovernmental Panel on Climate Change (IPCC) is now conducting technological and socio-economical assessments of climate change mitigation measures. The objectives of this research are, in conjunction with the IPCC activities, to perform investigation on the draft of the Third Assessment Report and the related literatures, and survey and study movements in technologies for climate change mitigation measures by performing investigations and researches by using models as required. Chapter 1 generalizes the activities of IPCC since 1988, and describes the preparation schedule for the third assessment report being worked on, as well as the summary movements thereof and the features of the third assessment report. Chapter 2 states the history of the activities. Chapter 3 describes that the third assessment report (draft) being prepared by the Working Group 3 is composed as a whole of the options of implementation, the theoretical background of the implementation, the international institutions, and the evaluation on the implementation. It generalizes the first order draft (FOD). Chapter 4 states the results of investigations on the points of issue which were regarded as the problems in the process of preparing the FOD. Chapter 5 describes the investigations of the FOD, making various important keywords as the axis of the investigations. (NEDO)

Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

Technological development for super-high efficiency solar cells. Survey on the commercialization on analysis; Chokokoritsu taiyo denchi no gijutsu kaihatsu. Jitsuyoka kaiseki ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on analysis of super-high efficiency solar cells for practical use in fiscal 1994. (1) On the survey on crystalline compound solar cells, it was pointed out that the present study target is III-V compound semiconductor solar cell, and efficiencies of 36-39% are theoretically expected by use of two-junction cells. (2) On structure of super-high efficiency solar cells of 40%, selection of upper and lower cell materials for multi-junction cells, high-efficiency tandem Si solar cells, and the merit and possibility of light collection operation were surveyed, and their issues were discussed. (3) On physical properties of mixed crystalline semiconductors and characteristic evaluation of solar cells, impurities, trap center, minority carrier life, and applicability of supper lattice structure to high-efficiency solar cells were surveyed. (4) On fabrication technology of compound semiconductor solar cells, various problems of and approaches to electrode formation and antireflection film technologies, the meaning and issues of thin film substrate technology and continuous process, trial calculation of costs, safety, and resource problem were surveyed.

FY 1993 annual report. Survey and study on establishment of databases for body functions; 1993 nendo shintai kino database no kochiku ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

As part of the health/welfare-related information collection, analysis and information service project, establishment of the databases is surveyed and studied for human life technology and body functions of the aged in the aging society. The survey/study on establishment of the human life technology for the aged covers concept of human life technology, systems of the databases for human life technology, and techniques for the database systems. The case study on the human life technology databases for the aged takes up everyday life behaviors of the aged as the models, and analyzes human and life characteristics in everyday life, to clarify the human characteristic, human performance and human life technology design data to be stored in the databases. The validity of the method developed by this project is tested for their behaviors, such as bathing and outgoing. For establishment of the databases for body functions of the aged, literature surveys and interviews are conducted for the technological trends. (NEDO)

Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

1997-02-01

Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

Study of recent fuel oil cost in air lines (Part 2). Saikin no airline no nenyuhi ni kansuru ichikosatsu (2); Nenryo shohi to hiyo tai koka

Energy Technology Data Exchange (ETDEWEB)

Tanabe, Yoshikazu.

1989-03-01

Through an arrangement of published data about American air lines during 1985 through 1987, the overall expense vs. transportation fee (expense vs. effect) was studied as a main viewpoint. As a result, the fuel oil cost, even in case of wide fuselage plane, high in transportation efficiency, was high in ratio, 32 to 52% (3 to 5 times as high as that 12 to 14 years ago), and fluctuated connectedly with the oil price. While the jet fuel price fluctuated connectedly with the oil price per equal volume with 1.3 to 1.4 of price ratio. Further, the flight range ratio was recorded to be approx. 0.06 to 0.24 km/kg. While the transportation efficiency was lower than approx. 5000kg*km/kg with a wide range of overall expense, approx. 9 to 87 cents per compensative transportation ton*km. Because even a sudden decrease in transportation quantity did not decrease the overall expense, it was known to be important in management to secure the transportation quantity. 30 refs., 15 figs., 1 tab.

Evaluation report on research and development of high-speed computation system for technological use; Kagaku gijutsuyo kosoku keisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-08-01

The above-named project is an effort implemented under the large-scale industrial technology research and development system through the cooperation of industrial, academic, and governmental circles in the nine-year-long period beginning in fiscal 1981. The project aims to establish technologies required for putting to practical use a high-speed computation system capable of speedily dealing with huge technological problems which the computers available at the commencement of the project failed to solve. The goals set for new devices and comprehensive systems were sufficiently challenging in view of the technological level of those days, and are still at the highest level in the world. It is judged that the goals were set with reason and appropriateness. The liaison council for the implementation of the project is constituted of people of experience or academic standing, entrusted research and development activities, Ministry of International Trade and Industry bureaus concerned, and the Electrotechnical Laboratory of the same ministry. Discussion, coordination, and communication on concrete matters are under way between the constituent members, contributing to the enhancement of research and development. The liaison council activities are evaluated to be appropriate and effective. (NEDO)

Research on a new rubber's absorber system for cable-stayed bridges. PC shachokyoyo shazai teichakubu shindo kyushuyo boshin gomu no shinkiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Oikawa, K.; Kibe, H.; Ohashi, W. (SE Corp., Tokyo (Japan))

1993-09-30

Cable-stayed bridges are being constructed increasingly and their maximum effective span length is becoming longer to the extent that it is about to reach the limit, thereby diagonal members which, by nature, tend to vibrate become much longer, hence problems concerning vibration have drawn attention. In this article, regarding vibration insulating rubber for absorbing vibrations to be set at an anchorage of diagonal members, a new mechanism has been invented and its analysis as well as demonstration experiment have been conducted. This mechanism is based on the concept that the vibration insulating rubber has been set beforehand at the time of installing the diagonal members, adheres to the diagonal members immediately after the diagonal members are stretched, but its adherence is released simply when tension adjustment is needed, and the spring constant of the rubber can be calculated simply within the range of practical use. The results obtained from the above analysis and demonstration experiment are as follows; it is necessary to set vibration insulating rubber in the vicinity of the anchorage of diagonal members in order to absorb vibrations of the members and the method to make its setting simple and secure has been confirmed. Also the calculation method of spring constant of vibration insulating rubber necessary for estimating the secondary bending stress of diagonal member has been confirmed, thereby designing of vibration insulating rubber has become easy. 8 refs., 14 figs., 2 tabs.

Proposal of self-anchored cable-supported bridge with main span length of 500m; Chuo span 500m kibo no jiteishiki tsurigatashiki kyoryo ni kansuru teian

Energy Technology Data Exchange (ETDEWEB)

Fukasawa, Y.; Sugiyama, T. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Kaneko, S.; Mukoyama, T.; Iwaki, T. [Pacific Consultants K.K., Tokyo (Japan)

1995-12-15

In order to investigate the feasibility of construction of cable-supported bridge at the site where ground condition is poor and/or air route restriction shoed be considered the static and dynamic characteristics of both self-anchored cable-stayed bridge with relatively low tower and self-anchored suspension bridge have been discussed. The main span length of bridge considered here is about 500 m because of the fact that stress resultant of main girder caused by design loads is considerably lower than its design strength in the existing cable-supported bridges of this scale. The result shows that the application of both types of cable-supported bridges to the above described site may be possible as enough static safety and economy are ensured. It has been also revealed that no problem may occur from both wind and earthquake resistant viewpoints. 10 refs., 24 figs., 8 tabs.

FY 2000 research cooperation project on plastic processing technology/quality inspection technology; 2000 nendo kenkyu kyoryoku jigyo. Plastic kako gijutsu hinshitsukensa gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of improving the production technology of plastic products in Saudi Arabia, the joint development was made of the formation technology/quality inspection technology of agricultural use and food packaging use polyolefin film optimum to environmental conditions of the site, in the light of the needs there, and the FY 2000 results were reported. In the field survey/joint study, for the xenon type weather resistant testing machine and the extruder of the inflation film forming machine which were transported from Japan, the following were carried out: confirmation of the situation of accepting them on the site, functional test of computer of the extruder, installation of the machine testing weather resistance, and the trial operation. In the domestic support study, the extrusion test at laboratory was conducted using the polyethylene resin produced on the site to acquire the basic data for formation stability. Further, the film formation test was made using the equipment with the same specifications as those of the equipment introduced to the site to study the performance of screw extrusion and the formation stability of film. Also conducted were the analytical test/quality evaluation of resin materials/film. (NEDO)

FY 1998 survey report. Examinational research on the construction of body function database; 1998 nendo chosa hokokusho. Shintai kino database no kochiku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The body function database is aimed at supplying and supporting products and environment friendly to aged people by supplying the data on body function of aged people in case of planning, designing and production when companies supply the products and environment. As a method for survey, group measuring was made for measurement of visual characteristics. For the measurement of action characteristics, the moving action including posture change was studied, the experimental plan was carried out, and items of group measurement and measuring methods were finally proposed. The database structure was made public at the end of this fiscal year, through the pre-publication/evaluation after the trial evaluation conducted using pilot database. In the study of the measurement of action characteristics, the verification test was conducted for a small-size group. By this, the measurement of action characteristics was finally proposed. In the body function database system, subjects on operation were extracted/bettered by trially evaluating pilot database, and also adjustment of right relations toward publication and preparation of management methods were made. An evaluation version was made supposing its publication. (NEDO)

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H [Toyo Construction Co. Ltd., Tokyo (Japan)

1997-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-08-01

Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

1998 research cooperation project. Research cooperation on environment-compatible type water resource effective-utilization system; 1998 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of securing water stably and preventing water pollution in the Philippines, R and D were carried out on a wastewater treatment and water reclamation and reuse system which is easy to operate and maintain and low in cost through the research cooperation between the Philippine Industrial Technology Development Institute and Japan. According to the survey result of statistical data concerning water pollution load structure by industrial wastewater classified by the industry in the Philippines, enumerated are the food manufacturing industry, paper pulp manufacturing industry, and the textile dyeing industry as those greatly affecting water pollution in BOD exhaust and wastewater, etc. Consequently, with Ram Food Product Co. of vegetable processing and Solid Mill Co., of textile dyeing as plants to be studied, a wastewater treatment test was performed in a laboratory scale. From the result of the test, the pilot plant was basically designed to have 'anaerobic + aerobic treatment + tertiary treatment' for the treatment process, with an one-tank type UASB method used as the anaerobic treatment, with a sand filtration + activated charcoal treatment as the tertiary treatment, and with the cost effectiveness for water reuse set to be examined. (NEDO)

Survey of subjects on the geothermal technology development aiming at marked improvement of economical efficiency; Keizaisei no hiyakuteki kojo to mezashita chinetsu gijutsu kaihatsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing the geothermal development cost and increasing the amount of developable resource, the paper reviewed the geothermal developmental technology. Approximately 30 MW as a scale per unit is economical. The development cost is lowered by 2% if the period for development is shortened by two years, by 11% if the utilization rate is increased by 10%, and by 3% if the success rate is increased by 10%. The cost is reduced by 10% if the steam amount per 1 pit is increased to 1.5 times, and by 4% if the reduction amount is increased to 1.5 times. Improvement of survey/exploration/evaluation technology and improvement of power generation/management technology contribute largely to making the above possible. The drilling depth also corresponds with increases in the amount of steam obtained and the cost. The construction cost including the drilling cost is also an important factor, indicating a cost reduction of 15% if the unit price is reduced by 20%. If a 30% reduction of the power generation cost at a 30MW plant can be made, a 10 yen/kWh is realized, which shows that a geothermal power plant can be competitive with a thermal power plant. When thinking of it without subsidies, the geothermal power generation is most economical of all the renewable energy. In the light of the environment, the CO2 issue, etc., the geothermal power generation is much more advantageous than the thermal power generation. 7 refs., 28 figs., 8 tabs.

Study on properties of mortar using silica fume and ground blast furnace slag. Silica fume oyobi koro slag funmatsu wo mochiita mortar no tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiiba, H; Honda, S; Araki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

1992-09-01

The effect of silica fume and ground blast furnace slag in concrete on the content of superplasticizer, and dynamic properties of hardened mortar with such admixtures were studied experimentally. Although the dependence of a flow value on the superplasticizer was dominated by kinds of superplasticizers, blast furnace slag enhanced the flow value resulting in a high fluidity. Adsorption of superplasticizers onto admixtures was dependent on kinds of superplasticizers, and adsorption onto blast furnace slag was 1.3-2 times that onto normal Portland cement (NPC). The compressive strength of mortar increased by mixing admixtures, while the bending strength was enhanced only by mixing silica fume. Mixing mortar was lower in dynamic elastic modulus than NPC mortar at the same compressive strength, and the velocity of supersonic wave in mortar was scarcely affected by mixing. 11 refs., 14 figs., 3 tabs.

Visualization and image analysis of dynamic stall phenomenon for a Darrieus wind turbine; Darrieus fusha ni okeru doteki shissoku gensho no kashika to gazo kaisekini kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fujisawa, N.; Shibuya, S.; Takano, T. [Niigata University, Niigata (Japan)

1999-10-25

The flow field around a Darrieus wind turbine is studied by flow visualization and PIV measurement in a rotating frame of reference to understand the unsteady nature of dynamic stall appearing at low tip-speed ratios. The qualitative nature of the dynamic stall observed by the flow visualization using dye injection technique is quantitatively reproduced in the instantaneous velocity distributions around the blade measured by PIV technique. These results indicate that two pairs of stall vortices are generated in one cycle of the turbine rotation and they grow in size as the tip-speed ratio decreases. The mechanism of the dynamic stall is found to be due to the flow separation over the suction side of the blade followed by the generation of in-flow motion from the pressure side to the suction side of the blade through the trailing edge. (author)

Research report of fiscal 1997. Basic research on the commercialization of innovative energy technologies; 1997 nendo chosa hokokusho. Kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper summarizes the research result in fiscal 1997 from the basic research results on the commercialization of innovative energy technologies. The target of a photovoltaic power generation market includes isolated power sources (several kWp) for distant places or developing countries, and those (several tens kWp) for personal residences or public facilities. Although the former is mainly promoted in the West, while the latter over the world, their profitability is unsolved. Power plants over several hundreds kWp are in demonstration test. Solar heat power generation of several tens to hundreds MWp is most profitable, however, small-scale one is poor in feasibility. Australia takes an interest in distributed photovoltaic power generation directly connected with actual lives of residents, and has a dominant opinion that desert is useless as large-scale site. This country lays emphasis on protection and maintenance rather than positive use of desert based on a basic cognition that desert is easily changed and broken. The Australian government announced power company`s obligation to use renewable energy by 2%, and a strong organization is scheduled to be newly established. 59 figs., 57 tabs.

Fiscal 1993 study of engineering for making areas prosperous using natural energy; 1993 nendo kankyo chowagata green techno system no kokusai kyoryoku model ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper studied the engineering for activating areas using natural energy. A system has started in which electric power companies purchase surplus electric power from the natural energy use power generation such as the wind power and photovoltaic power generation, etc., and a lot of local self-governing bodies in the country plan `projects to promote town` using the system. However, few engineers and makers can plan `a project to promote town,` making effective use of natural energy which is fickle. Therefore, first, the paper arranged the actual status mostly of the cases of `the projects` using natural energy which have been carried out in the country. Next, the trend of the natural energy utilization technology in countries including the U.S. was described. Moreover, assuming model areas in Japan for working out a concept of model projects on the natural energy utilization and town promotion, a concept was proposed making full use of the utilization technology which has now usability. Arrangement is being made for conditions for the full scale spread as seen in the subsidy system for general users. 3 refs., 176 figs., 61 tabs.

Fiscal 1999 survey report. Survey of leading countries' approaches to biomass energy development; 1999 nendo shuyokoku ni okeru biomass energy kaihatsu eno torikumi ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The survey aims to help Japan deliberate its future biomass energy development strategy including the course Japan is to follow in its research and development of biomass energy by clarifying leading countries' approaches to the subject matter and trends of their research and development efforts in this connection. The states of biomass energy development in the U.S. and Europe are reported. In the U.S., President Clinton issued Executive Order 13134 on August 12, 1999, regarding bio-based products and bioenergy development. In this country, bioenergy and bio-based production technologies have developed to reach a stage where business pays, and commercial plants are in service. The U.S. Administration mentions as a strategy the efficient development of the bioenergy industry. In Europe, where resources are versatile and local, it is difficult to assess the economy of scale, and small-scale development efforts are being accumulated. Practical technologies under development mostly involve direct combustion. European measures are similar to U.S. measures in that such political goals as local development and employment promotion are firmly woven into them. (NEDO)

Reports on 1974 result of Sunshine Project. Research on tar sand and oil shale; 1974 nendo tar sand oyobi oil shale ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-04-04

The purpose of this research is to grasp the policy of the oil sand resource countries, the properties and existing conditions of the resources, effects of the oil sand resources on a long term energy supply/demand, etc., and to clarify the meaning and position of the researches on the development of oil sand resources in the future energy policy of Japan. The quantities of oil sand resources are mostly in the process of investigation except Alberta province of Canada and are estimated to be two trillion barrels. The quantity for which strip mining is possible is about 90 billion barrels, which are mostly located in the Athabasca region. The oil sand holding countries take a policy of positively developing oil sand. No barriers are particularly provided against the introduction of foreign technology and capital. Where the prospects are possible for the development of oil sand are Canada and Venezuela. R and D should be emphasized on the refining of bitumen and the extraction method within the oil reservoir. The investment per b/d is about 15-20 thousand dollars, which is likely to be more than twice as much as for the North Sea oilfields. The properties and quality of the synthetic crude oil are superior while the risk of exploitation is small; therefore, oil sand will be competitive with crude oil in the future. (NEDO)

Report on surveys in fiscal 2000 on the survey on promotion of freer flow of researchers; 2000 nendo kenkyu jinzai no ryudoka sokushin ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to help discuss the system and environment improvement to promote freer flow of Japanese researchers, surveys and discussions were given on the actual status in America and European countries. In the U.S., results as independent researchers are demanded from the very early time under the severely competitive environment, wherein the fair evaluation of the results allows the researchers to step-up the positions and research environment to which the researchers are oriented. In Germany, a function to promote researcher mobility is available as a system, such as promotion of exchange with other sectors during researcher education course (the internship system at the fourth grade in a university, and power training and performance record building at the Max-Planck Institut during the long term of post-doctoral period before attaining a professor position), or prohibition of inviting university professors into the same faculty. The actual status of Japan not having high mobility of researchers has been caused by the system based on the lifetime employment, whose shortcomings include stiffness in personnel affairs, and reduction in activities of researchers due to aging. (NEDO)

Report on the FY 1999 research survey on the development of high ductile chromium alloys; 1999 nendo koensei kuromu gokin no kaihatsu ni kansuru kenkyu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D of chromium alloys had been conducted till about the 1970s, which brought the unfavorable results. That's why chromium alloys are brittle at normal temperature and difficult in processing. However, the technology development in recent years review them. The development is earnestly desired also of the materials exceeding the Ni base super alloys which are heat resistant materials for power generation. Cr is rich as resource and light-weighted, and the oxidation film is stable and self-restorational at high temperature. The alloys are excellent in processability at normal temperature and excellent also in toughness. The nitrogen content is strongly concerned with brittleness and intergranular fracture at normal temperature. Therefore, Cr alloys were trially manufactured by the HIP sintering/hot forging method using electrolytic Cr powder with high-purity (99.99%) and low-nitrogen (10ppm) to study a possibility of improving brittleness at normal temperature, mechanical properties at high temperature, oxidation resistance, high-temperature corrosion resistance, etc. A variety of excellent characteristics of Cr alloys were made clear. However, also made clear were the problems: strength is low at normal temperature/high temperature; screw process is impossible because of high notch sensibility; those are not almighty high-temperature corrosion resistant materials. Further efforts should be exerted for the commercialization. (NEDO)

Report on survey in fiscal 2000 on the feasibility study on structuring research aiding net; 2000 nendo kenkyu shien net no kochiku ni kansuru kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A study has been performed on the possibility of efficient utilization of research resources by summarizing the resource information for research and development by the industrial, governmental and academic areas and by providing research organizations with the information through the Internet. As a result of the survey on research aiding cases that apply the network used by the public organizations and corporations inside and outside the country, it was found that Japan often utilizes research facilities and holds seminars having selected regional research organizations, while the U.S. provides large-size aids in wide area, such as technological information service, patent service, and human resource service. A questionnaire survey was conducted on interests toward the necessity of research aids, specific needs for aids, and provided services. As a result, it was revealed that interest toward the research aiding net is considerably high, and strong demands are present in structuring database for the research human resource information, needs information, and information on researchers in different fields. Discussions were given on structuring the research aiding net, wherein the system contents, structuring expense, and the development schedule were presented. (NEDO)

Report on the FY 1999 R and D survey on ultra-high sensitive photoelectric converter; 1999 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

By the ICB method which is one of the ion engineering methods, photomultipliers were formed using organic dye thin films. By changing the energy to bond traps on thin film/metal electrode interface and electric charges by change of acceleration energy of ion beams, a technology was developed for adjusting the optimum operating temperature between -20 degrees C and +100 degrees C. The wide range of operating temperature and favorable SN ratio can be realized. It was made clear that the dark current of the photomultiplier is composed of two components of contribution by the residual charge stored on the interface at photomultiplying and of contribution by charge injection from the Schottky barrier. Based on this, the residual electric charge removal method by heating and applied pulse voltage was developed. The development for practical use was studied of ultra-high sensitive photoelectric converters. As an intelligent photo sensor, a biomimetic visual photosensor was proposed which uses amplification/memory/arithmetic functions and film formation/processability of organic thin films. The paper also described the image sensor. (NEDO)

Research on adoption of graphic processing system into electric power facilities operation management. Denryoku setsubi kanri gyomu ni okeru zukei shori system no tekiyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Jitsubuchi, Yoshiyasu; Uryu, Kenji; Terasaki, Naoaki (Kyushu Electric Power Co., Inc., Fukuoka (Japan))

1989-03-30

In the technical department of electric power companies, there are innumerable single line diagram, machinery arrangement plan and other facilities drawings. Based on those drawings, facilities planning, work design, construction plan, maintenance and management data, etc. are made, for which making heightening is desired in efficiency of drawing filing management. Therefore, research was made on the adoption of CAD technology through modeling power transmission line, and power generating and transforming station operation management. First for the application of power transmission facilities, the power transmission line plan and facilities information were planned to be unified in management. Ie., the power transmission line plan and profile being shown on the display, symbols of steel towers, cable lines, etc. were further picked by mouth to easily substantiate the facilities. While image input and CAD of drawing were made in combined treatment. Then for the application to the power generating and transforming facilities, the single line diagram and facilities information were unified in management, together with demonstration of data interchangeability among different kinds of CAD system. 13 figs., 9 tabs.

Study of the heat island phenomenon in large cities and the measures to prevent it; Daitoshi ni okeru heat island gensho to sono taisaku ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kawasaki, T.; Ishitani, H.; Matsuhashi, T. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1997-01-30

The paper made an analysis of the heat island phenomenon in the Kanto area using 3-D numerical analysis models and a study on the effectiveness of the measures to prevent it. The models are composed of advection/diffusion models of heat/steam in the wind-velocity field and atmospheric air, heat diffusion models in the underground and undersea, and heat balance models on the ground surface and sea surface. In the calculation, a simulation was conducted of the case of taking the following three measures: the case where the exhaust heat was reduced 30% in the assumed typical day of summer; the case where the heat volume of buildings/trunk roads was reduced; the case where the evaporation efficiency of buildings/trunk roads was raised. The result of the study was as follows: The reduction effect of the exhaust heat is totally large, but precisely observing, some meshes contrarily showed rises in temperature in the suburbs. Also in the case of reducing the heat volume, the same phenomenon occurred, but the effect was large in the center of a city. It was found that the effect was unexpectedly large in the case of increasing the evaporation efficiency. 7 refs., 14 figs., 2 tabs.

FY1998 report on the surveys and studies on developing next generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For further resource and energy conservation and environmental load reduction, development is necessary on innovative chemical reaction technologies. This paper describes surveys on next generation chemical processes. As non-halogen processes subject to development of new catalysts, new processes were investigated and searching experiments and discussions were given on isocyanate, propylene oxide, and phenol. Technological progress in the C1 chemistry was investigated. Problems in hydrocarbon compound oxidation, hydroxylation, and decomposition by utilizing microorganisms were put into order as application of environmentally friendly technologies. Marine biotechnical possibilities were surveyed. The surveys were given on new processes utilizing the phase transfer catalyst forming a third phase, manufacture of biodegradable plastics, and a novel reaction system combined with self-separation process using molecular assembly. Possibilities were searched on designing a truly simple production system of highly energy saving type. Such fundamental common technologies as structure analysis, property control and reaction engineering were investigated for methods to manufacture functional micro-powder chemical materials. Development was discussed on a system for technology assessment over whole product life cycle to structure a technology assessment basis. (NEDO)

FY1995 study of very flexible software structures based on soft-software components; 1995 nendo yawarankana software buhin ni motozuku software no choju kozo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this study is to develop the method and tools for changing the software structure flexibly along with the continuous continuous change of its environment and conditions of use. The goal is the software of very high adaptability by using soft-software components and flexible assembly. The CASE tool platform Sapid based on a fine-grained repository was developed and enforced for raising the abstraction level of program code and for mining potential flexible components. To reconstruct the software adaptable to a required environment, the SQM (Software Quark Model) was used in managing interconnectivity and other semantic relationships of among components. On these two basic systems, we developed various methods and tools such as those for static and dynamic analysis of very flexible software structures, program transformation description, program pattern extraction and composition component optimization by partial evaluation, component extraction by function slicing, code encapsulation, and component navigation and application. (NEDO)

Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aoyama, K.; Sawada, K. [The University of Tokyo, Tokyo (Japan)

1996-12-31

Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

Study on the detonation properties of explosives in bore hole and precise controlled blasting; Happa konai no bakuyaku no bakugosei to seimitsu seigyo happa ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-08

In order to perform efficient and safe controlled blasting, attaining sufficient detonation from explosive is important. Therefore, a mechanism of detonation in a bore hole was studied. Two detonation phenomenon measuring methods were established: one is a continuous detonation speed measuring method by using a resistance wire probe, and another is a detonation mark observing and evaluating method using aluminum and metallic lead plates. Assuming delay blastings in multiple bore holes used practically, discussions were given on detonation phenomena of explosives under pressurized condition. Under dynamic pressure condition, size of the pressurization and delay time of the detonations affected largely the detonation. Discussions were given on blasting effect and safety according to difference in forward initiation and reverse initiation. The reverse initiation method was verified to have excellent blasting effect, maintain good face conditions, and assure safety against inflammable gases. A precision initiation method was developed, which can control the initiation time of a detonator more precisely. The initiation accuracy is more than 1000 times greater than the ordinary instantaneously detonating electric detonator. The precision control of the initiation time proved to develop greater crack propagation. Vibration and stone scattering were also controlled. This paper also describes application of the method to a rock elastic wave exploration technique. 136 refs., 99 figs., 13 tabs.

Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

Report on evaluation of research and development of light-aided instrumentation/control systems. Abstract; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-08-01

This research and development project is aimed at commercialization of the light-aided instrumentation technology systems which safely, stably measure, transmit and control process information including image information, e.g., temperature, flow rates and components at large plants in industrial complexes, in the severe atmospheres in the presence of, e.g., electromagnetic induction and combustible gases. These optical systems need development of light transmitting/receiving devices, various optical devices that constitute the network nodes, and various types of sensors of improved functions and reliability, in addition to development of the techniques required for transmitting large quantities of information on a large scale. This project has attempted to systematically make break-through in the individual elementary techniques, in particular those in the widely diversified technological areas for the advanced devices, and thereby to expand the instrumentation/control technology frontiers. The results of studies on gallium/arsenic crystals, which are prerequisite for photoelectronic integrated circuits as the bases for the light application technology, and processes for producing thereof are highly rated worldwide. It is planned to effectively utilize the total system, constructed at then Nippon Mining's Mizushima Refinery, and thereby to establish the effective instrumentation techniques for commercial plants and to promote commercialization of these results. (NEDO)

Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, K. [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H. [Toyo Construction Co. Ltd., Tokyo (Japan)

1996-12-31

The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

Simulation model study of limitation on the locating distance of a ground penetrating radar; Chichu tansa radar no tansa kyori genkai ni kansuru simulation model no kochiku

Energy Technology Data Exchange (ETDEWEB)

Nakauchi, T; Tsunasaki, M; Kishi, M; Hayakawa, H [Osaka Gas Co. Ltd., Osaka (Japan)

1996-10-01

Various simulations were carried out under various laying conditions to obtain the limitation of locating distance for ground penetrating radar. Recently, ground penetrating radar has been remarked as location technology of obstacles such as the existing buried objects. To enhance the theoretical model (radar equation) of a maximum locating distance, the following factors were examined experimentally using pulse ground penetrating radar: ground surface conditions such as asphalt pavement, diameter of buried pipes, material of buried pipes, effect of soil, antenna gain. The experiment results well agreed with actual field experiment ones. By adopting the antenna gain and effect of the ground surface, the more practical simulation using underground models became possible. The maximum locating distance was more improved by large antenna than small one in actual field. It is assumed that large antenna components contributed to improvement of gain and reduction of attenuation during passing through soil. 5 refs., 12 figs.

FY 1998 annual report on the research and development of superhigh-sensitivity photocurrent conversion devices; 1998 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are research and development of superhigh-sensitivity photocurrent conversion devices. The huge photocurrent multiplication effect exhibited by a thin film of organic pigment semiconductor is expected to be applicable to various new devices, e.g., superhigh-sensitivity, intelligent optical sensor families and photocurrent devices. Photocurrent multiplier thin films of perylene is prepared by an ionized cluster beam method, to evaluate their structures and photocurrent characteristics as the basic knowledge for controlling their characteristics by the ion engineering procedures. Photocurrent multiplier thin films of new, two-layer structure are developed, and improvement and stabilization of their characteristics are studied. Increasing sensing sensitivity by, e.g., introduction of p-n junction and reducing dark current resulting from the light memory effect are found to be effective to improve the S/N ratio. An organic EL light-emitting layer capable of positive/negative feedback, as one of the elementary techniques for realizing intelligent devices, is made on a trial basis and evaluated for its characteristics, and studied for its application to photocurrent multiplier thin films. Functional devices in which the arithmetic and controlling functions of the thin films are utilized are also studied. (NEDO)

Preparation and utilization of amorphous siliceous materials from serpentine (Mg3Si2O5(OH)4) by acid treatment; Jamonseki no kofuka kachika ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-30

Concerning the conversion of serpentine, not only its magnesium component but also silica component, into industrial materials, conditions suitable for the production of porous materials and amorphous silica by acid treatment were evaluated, and the properties of the products were evaluated. The silica resulting from the acid treatment of serpentine comes out in different forms, each reflecting the structure of the parent rock, that is, an amorphous mass of planar particles from antigorite and a fascicular mass of filaments from chrysotile. A microporic structure resulted when a small quantity of magnesium was allowed to remain in the skeleton structure and acid treatment conditions were properly adjusted. Several siliceous compounds were prepared for the purpose of finding use for silica from this rock, and then it was found that high-efficiency production of high-crystallinity compounds was possible and that they were furnished with properties fit for use as materials. Furthermore, study was made about the kaolinite reaction in which serpentine would be directly converted into useful materials. 105 refs., 55 figs., 6 tabs.

Knowledge capital, productivity and competitiveness. Empirical evidence for the G-5 countries; Chishiki shihon no chikuseki to seisansei kokusai kyosoryoku. G5 shokoku ni kansuru jissho bunseki

Energy Technology Data Exchange (ETDEWEB)

Sakurai, N.; Miyazaki, H.

1999-06-01

Technological change is a major driving force for long-run economic growth. New theories on growth have stressed the importance of innovative and adaptive capacity of firms in order to fully reap the benefits of research and development (R and D) within the firms as well as those spilled-over from other firms and abroad. This report empirically investigates the relationship between R&D and productivity as well as that between productivity and industrial competitiveness for the G-5 countries (Japan, the US, (West) Germany, France and the UK). To do so, we have constructed comparable data on R and D capital stock (so-called 'knowledge capital'), the level and growth rates of total factor productivity (TFP), and the revealed comparative advantage (RCA) index for 22 manufacturing industries in each G-5 country. The major results are summarized as follows. First, the volume of knowledge capital for Japan is still far smaller than that of the US (40% for total manufacturing in 1995). Second, there is no clear tendency of TFP convergence to the US level for each country after 1980 and its level for Japan is about 70% of the US in 1993. In addition, the TFP gap between Japan and the US has recently widened for high-tech sector. Third, the estimated elasticities of TFP with respect to the R&D stock for manufacturing sector during the mid-1970s and the early 1990s are 0.07 for Japan and 0.21 for the US on average, with deteriorating R and D potency in Japanese manufacturing. For high-technology industries, they are much larger with the estimates of 0.45 for Japan and 0.86 for the US on average, whereas for Japan the R&D performance becomes worse during the last decade. Fourth, we found that international competitiveness in industries depends not only on TFP and exchange rate fluctuations, but also on various non-price factors such as product quality, marketing ability, and product market segmentation. (author)

Study on a new type variable valve lift timing mechanism with a three dimensional cam; Sanjigen cam ni yoru shinkahen valve lift timing kiko ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ogura, M; Song, C [Nippon Institute of Technology, Saitama (Japan)

1997-10-01

The variable valve timing mechanism was invented to get a torque band at wide engine speed, and to reduce a compression job and pumping loss by a miler cycle at partial load. In this paper, the new type variable valve timing mechanism applying a three dimensional cam was proposed. Also, the feature of mechanism and the control system was done obviously. Further, about a miler cycle, a thermodynamics -like consideration was described. 5 refs., 8 figs.

Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

FY1995 study on objective measurement of mental stress caused by operation; 1995 nendo kiki sosa ni okeru seishinteki fuka no kyakkanteki keisoku gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The task with operating highly functional and intelligent machines, is supposed to cause the mental stress such as tension, anxiety or fear, owing to the operation itself and movement of the machines. The purpose of the project is to establish the physiological sensing technique in objective measurement of the various mental stress caused by the operation or the movement of machines, aiming at designing the optimal interfaces in man-machine system. Subjective quantities and physiological responses are measured, under the stresser of five different conditions, such as a monotonous task, a task which causes tension, and a motion of a robot which causes fear. BP, ECG, and are measured as Physiological items. More precisely, the variation in systolic pressure, RRI of heartbeat or LF/HF value obtained by its spectrum analysis, and the power spectrum of a wave or CNV area derived from spectrum analysis of EGG, are obtained for each item. The results of the experiment show that subjective responses such as irritation, tension and concentration due to the increase of the task load, and fear caused by the movement of machines, are able to be measured by physiological responses such as BP, ECG and EEG. (NEDO)

Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aoyama, K; Sawada, K [The University of Tokyo, Tokyo (Japan)

1997-12-31

Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

FY 2000 report on the survey on the long-term energy technology strategy, etc. - Basement technology for implementation of industrial technology strategy. Survey on the extraction of preferential important technical subjects in FY 2002; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho - sangyo gijutsu senryaku sakutei kiban chosa. 2002 nendo yusenteki juyo gijutsu kadai no chushutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey is to investigate the consciousness of researchers and engineers of enterprises, universities, etc, of the importance of about 100 important technical subjects in 'the industrial technology strategy' prepared by the Ministry of Economy, Trade and Industry. In the questionnaire survey, the following were selected: 1)systematization of policy in consideration of the social needs and R and D of the technology to realize it; 2) R and D of the technology to advance the future frontier; 3) technical subjects that the government should promptly start to tackle in each classification in arrangement of the intellectual basis. Answers to the following items were obtained: 'selection reasons' for why it was considered important in each technical subject, 'lead time' toward the time of the industrialization, 'international positioning' of Japan against Western countries, 'possibility of heightening/maintaining the international competitive force,' and 'items that the government should participate in.' In 1), the following four big targets were arranged: 'security/safety,' 'informatization,' 'environment' and 'energy'. In 2), the following technical subjects were arranged: 'biotechnology,' 'information communication technology,' 'production technology,' 'materials/process technology,' 'energy/environment' and 'new blending/traversable/integrated technology.' In the results of the survey, analyzed were big targets, and trends and characteristics at technical field levels. (NEDO)

FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Investigational study of behavior of trace impurities in the liquefaction process); 1974 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Ekika katei ni okeru biryo fujunbutsu no kyodo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-28

Hydrogen gas as material is produced mostly by steam reforming of hydrocarbons, and includes a considerable amount of impurities such as carbon dioxide, nitrogen and oxygen. The concentration of impurities in the refined gas is approximately 1ppm. In the liquefaction process of hydrogen liquefaction plant, the gases entering the low temperature portion near the free expansion valve (J-T valve) are mostly oxygen and nitrogen. When oxygen is solidified, attached, accumulated near J-T valve, it incurs a possibility of exploding for reason of impact force, etc. by contact with the valve portion. A mixture of hydrogen and oxygen ignites at the minimum value of approximately 0.02 milli-joule, and therefore it has great danger of explosion. As viewed from a point of danger prevention, there is a possibility of explosion when the hydrogen-oxidizing agent mixture is formed. Accordingly, it is necessary to conduct an experiment for confirming the explosion at J-T valve portion. From viewpoints of prevention of explosion accident and running operation, it is necessary to experimentally grasp the definite allowable oxygen concentration. Further, it is necessary to establish a technology to continuously and accurately measure the concentration of trace impurities in hydrogen gas. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Report on achievements in fiscal 1998. Survey on environmental effects from photovoltaic power generation systems; 1998 nendo daikibo taiyoko hatsuden system no kankyo eikyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Different environmental effects may be assumed when large-size photovoltaic power generation systems are installed in vast unutilized lands including deserts. Knowledge having been acquired to date has been put into order on the following subjects as the pre-survey thereon: (1) environmental characteristics of desert areas, (2) discussions on environmental effects from (a) environmental assessment viewpoints, (b) contents of the environmental assessment, and (c) environmental assessment institutions, and (3) the survey policy. In discussing the environmental characteristics, it is revealed that desert areas are neither sterile nor unused, but pasturage and agriculture have been carried out in historical and traditional ways. In discussing the environmental effects, it was recognized that surveys on primary and secondary effects on the environmental are indispensable. With regard to the institutions, there are countries who have and have not the institutions even among the OECD member states. In addition, it was known that environments in the desert areas vary greatly according to the particular areas, whereas there are possibilities of installing the facilities because the effects of the facility locations on the environment are various. Therefore, it was decided to start from the case studies in locations of different types. (NEDO)

Research and development cooperation project on environmental measurement using laser radar (environmental network) in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

For the purpose of contributing to the research cooperation project on the development of a laser radar for environmental measurement, the paper surveyed the present and future trend of the environment related information network in Indonesia. The survey was conducted in terms of a name of the network, the main administration body, the number of users, the utilization status, the use protocol, details of service, domestic mode installation sites and the main administration body, accounting system, types of the network used, reliability and stability of network, limitations on the use and details of the limitation, etc. The plan for expanding telecommunication equipment is being advanced in a very quick tempo. However, there are many problems in digitalization, and it is feared that the plan will be delayed. As to telecommunication quality and connection quality, the telecommunication completion rate, SCR, is very low, approximately 24% on average, which is equal to that around 1990 in Japan. The business service for users is all bureaucratic since they have a lot of applications for the installation piling up with no exception to the rule of developing countries. 23 figs., 10 tabs.

Study of initial stage in coal liquefaction. Increase in oil yield with suppression of retrogressive reaction during initial stage; Ekika hanno no shoki katei ni kansuru kenkyu. 1.

Energy Technology Data Exchange (ETDEWEB)

Uesugi, K.; Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

1996-10-28

For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogen transfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic effect between the improvement of liquefaction by suppressing polymerization/condensation at the initial stage of reaction through the prethermal treatment and the effective hydrogen transfer accompanied with the improvement of contact efficiency of coal/catalyst by the concentration of slurry at the stage of liquefaction. 4 refs., 8 figs.

Fiscal 1998 research report. Research on energy conversion technology using biomass resources; 1998 nendo chosa hokokusho. Biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study was made on construction of the new energy production system by thermochemical conversion or combination of thermochemical and biological conversions of agricultural, fishery and organic waste system biomass resources. This report first outlines types and characteristics of biomass over the world, proposes the classification method of biomass from the viewpoint of biomass energy use, and shows the introduction scenario of biomass energy. The energy potential is calculated of agricultural waste, forestry waste and animal waste as the most promising biomass energy resources, and the biomass energy potential of energy plantation is estimated. The present and future of biochemical energy conversion technologies are viewed. The present and future of thermochemical energy conversion technologies are also viewed. Through evaluation of every conversion technology, the difference in feature between each conversion technology was clarified, and the major issues for further R and D were showed. (NEDO)

Research report for fiscal 1998. Study of utilization of biomass including foods in energy industry; 1998 nendo shokubutsu nado no biomass no energy riyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Rice being produced as food is taken up out of various types of biomass, and a feasibility study from the viewpoints of technology and economy is conducted as to its use in the energy industry. The production of ethanol from rice, though it has no past record worth discussion, is similar to the production of ethanol from other biomass resources in terms of technology and economy. The problem is that the production cost of rice is far higher than those of other materials. It is expected, however, that there will a large-scale production cost reduction and an increase in the yield when novel cultivation techniques are introduced in the future. It is also expected that alcohol from rice will be sufficiently competitive with alcohol from molasses or the like when the exploitation of cellulose-family by-products such as husks becomes feasible. The study on this occasion deals solely with the effective use of farmland and the surplus rice. A confrontation between rice as a biomass resource and rice as a food has to be avoided as much as possible in the long term because it may cause a price rise and compromise the security of food supply. That is, in discussing this matter, it is mandatory to draw a very definite line between rice as a food and rice as an alcohol production material. (NEDO)

Investigation into the analysis method of total ecobalance in chemical industry products. 3; Kagaku kogyo seihin ni okeru total eko balance no bunseki shuho ni kansuru chosa. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of establishing a total life-cycle ecobalance analysis (LCA) method, the paper studied making of a general computer program for chemical industry products. The study has been made on general-purpose plastics (PET/PSP (polystyrene paper)) since fiscal 1993 aiming at making the CO2 emission computing program covering the entire process of production from extraction of raw materials through waste disposal. In fiscal 1995, the following were conducted for enhancement of generalization of the method: expansion of environmental load items and increase in validity of the concept, and expansion of database. Notice was taken of not only CO2 but SOx, NOx and water quality load items. The survey was made on the recycling situation in Japan and abroad and the PET recycling plant , and environmental load item data are collected to expand database. The program was verified by analyzing an example of reusing PET bottle to carpet, and one-step development can be made toward the establishment of the method. Moreover, an analysis was made for the environmental assessment of the related programs abroad, and a tentative original plan can be proposed for the standardization of environmental load analysis and the integrated assessment method. 39 refs., 130 figs., 76 tabs.

Research and development cooperation project on environmental measurement using laser radar in fiscal 1994 (environmental network); Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Under the R and D of a laser radar for environmental measurement which are conducted in cooperation with Indonesia, the paper reported the R and D of the environmental network in fiscal 1994. Four field surveys were made, and the following were conducted: proposal of a technical system, adjustment of the Asian environmental information network with BPPT and LIPI which are organs on the Indonesian side, installation of/technical discussion on network equipment, etc. There is IPTEKNET as a plan of a nationwide network of the scientific technology information service in Indonesia. The analytical design phase of this system converged in 1992, and the predicted investment amount in the coming five years is expected to be 6.7 million US dollars. As the future Asian environmental information network work, planned are connection between BPPT and Tokyo CC and connection at BPPT between the Asian environmental information network and IPTEKNET. Network managers at sites are very skillful, and therefore, the thorough cooperative work is anticipated. 24 figs.

Survey on actual status of R and D fund assistance in the U.S.A.; Beikoku ni okeru kenkyu kaihatsu shikin enjo no jittai nado ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

As a basic survey to serve for establishment of science and technology policies, a survey was carried out on the actual status of R and D fund assistance in the U.S.A., roles of the government and civil sectors, and how they are interrelated. The survey was performed in detail on the following items: the assistance and cooperation measures taken by the U.S. government, and technological policies of the U.S. government; fund subsidies and policies toward technological research and development provided by the U.S. government; research and development plans and projects being the object of the subsidies given by the U.S. government; assistance and cooperation of private organizations for financing research and development activities in the U.S.A.; cooperation and joint works among industries, the government and universities (research consortiums) in the research and development activities; legal assistance policies for research and development in the U.S.A., the favorable tax system for research and development, the 1984 National Joint Research Act, and the actual status and analysis of the legal assistance policies in the U.S.A. for aiding research and development tests. (NEDO)

Investigational study of the CO2 balance in high temperature CO2 separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

An investigational study was conducted to clarify the adaptable environment and effectivity of technologies of high temperature separation/recovery/reutilization of CO2. In the study, data collection, arrangement and comparison were made of various separation technologies such as the membrane method, absorption method, adsorption method, and cryogenic separation method. With the LNG-fired power generation as an example, the adaptable environment and effectivity were made clear by making models by a process simulator, ASPEN PLUS. Moreover, using this simulator, effects of replacing the conventional steam reforming of hydrocarbon with the CO2 reforming were made clear with the methanol synthesis as an example. As to the rock fixation treatment of high temperature CO2, collection/arrangement were made of the data on the fixation treatment of the CO2 separated at high temperature into basic rocks such as peridotite and serpentinite in order to clarify the adaptable environment and effectivity of the treatment. Besides, a potentiality of the fixation to concrete waste was made clear. 57 refs., 57 figs., 93 tabs.

Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

Research and development cooperation project on environmental measurement using laser radar in fiscal 1995 (environmental network); Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

As a part of the cooperative work with Indonesia of R and D of a laser radar for environmental measurement, the paper described the development of an environmental network. The field survey was conducted in April, July and December 1995 and in March 1996. For the investigational research, five meetings of the committee and four times of group work were held. The Asian environmental network was studied in terms of its arrangement, operation and management, and the overall network/path control design were being prepared. To make the persons concerned abroad and in Japan understood the APEC Osaka Conference held in November 1995, a homepage APEC `95 Kansai was opened using WWW (World Wide Web, a decentralized hyper media system which can dispatch information to the whole world by network using hyper text). Moreover, in connection with this, a homepage was opened of CICC (Center of the International Cooperation for Computerization, a center controlling the whole Asian environmental information network system where E-mail and data are exchangeable with Indonesia via Tokyo NOC (Network Operation Center)). 49 figs., 8 tabs.

Study on particle behavior in the expansion of fluidized bed using a simple optical probe. Kogaku probe wo mochiita ryudoso no bocho sonai ryushi kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kato, Y; Miyamoto, M [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Chimura, T [Toyota Motor Co. Ltd., Tokyo (Japan); Idei, Y [Ube Industries, Ltd., Tokyo (Japan)

1991-09-25

In order to clarify the relationship between the heat transfer rate and the expansion bed in a group of horizontal pipes in a freeboard region (an area of the heat-transfer pipe exposed above the height of static particle bed from the beginning) in a cold model of the fluidized bed, particle behavior was measured using an optical measuring method. The light axis position was set higher than the heat-transfer as X {sub p} in a direction perpendicular from the distributor, and the static bed height was set to L {sub c}. The frequency of particles and particle lumps coming to presence between the light axes is termed V {prime}{sub p}(time-averaged dimensionless amount of the optical probe output). The V {prime}{sub p} decreases with an increase in the flow velocity, and, when the difference between the probe tip and the static bed height, X {sub p}{minus} L {sub c} is small, it shows the minimum value at a certain flow velocity and then rises again. The root mean square value of the probe output, V {prime}{sub f} increased with an increase in the flow velocity, reached its maximum, then decreased to the minimum, and rose again. The flow velocity that takes the maximum heat transfer rate can be identified from the relationship among the dimensionless amount of the maximum expansion bed height and the average expansion bed height, the dimensionless height of X {sub p} when V {prime}{sub p} and V {prime}{sub f} obtained at each X {sub p} show the extreme values, and the dimensionless height of the heat-transfer pipes when the average transfer rate takes the maximum value. 6 refs., 5 figs.

Report on follow-up for joint research of valuable resources recovery techniques from brackish water; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku follow up hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report describes follow-up for research and development on the recovery of valuable resources, such as magnesium, bromine and boron, contained in the brackish water for manufacture of common salt in the coastal region of Mexico. For the field survey, salt garden, irrigation plant and manufacturing plant of dinning salt were inspected. The optimum site was examined by assuming desalination plant and solar pond. The groundwater in coastal regions is progressively salified. Since the coastal region is a tourist resort with an round-trip area of whales, environmental protection is indispensable. For the joint research with invited researchers, the solar pond system and fresh water generation were studied. As a result, it was found that the solar pond system is an excellent method for keeping thermal energy in a low cost at the salt garden with abundant solar energy, and that the desalination system combined with distilling is the most suitable method. 7 refs., 8 figs., 1 tab.

Integrated interpretation of AE clusters and fracture system in Hijiori HDR artificial reservoir; Hijiori koon gantai jinko choryuso no AE cluster to kiretsu system ni kansuru togoteki kaishaku

Energy Technology Data Exchange (ETDEWEB)

Tezuka, K [Japan Petroleum Exploration Corp., Tokyo (Japan); Niitsuma, H [Tohoku University, Sendai (Japan)

1997-05-27

With regard to a fracture system in the Hijiori hot dry rock artificial reservoir, an attempt was made on an interpretation which integrates different data. Major factors that characterize development and performance of an artificial reservoir are composed of a fracture system in rocks, which acts as circulating water paths, a heat exchange face and a reservoir space. The system relates not only with crack density distribution, but also with cracks activated by water pressure fracturing, cracks generating acoustic emission (AE), and cracks working as major flow paths, all of which are characterized by having respective behaviors and roles. Characteristics are shown on AE cluster distribution, crack distribution, production zone and estimated stress fields. Mutual relationship among these elements was discussed based on the Coulomb`s theory. The most important paths are characterized by distribution of slippery cracks. Directions and appearance frequencies of the slippery cracks affect strongly directionality of the paths, which are governed by distribution of the cracks (weak face) and stress field. Among the slippery cracks, cracks that generate AE are cracks that release large energy when a slip occurs. Evaluation on slippery crack distribution is important. 7 refs., 8 figs.

Fundamental study on leak detection of underground gas pipeline using passive acoustic method; Judogata onkyo keisoku ni yoru maisetsu gas dokan hason kasho no kenshutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Jinguji, M; Imaizumi, H; Kunimatsu, S; Isei, T [National Institute for Resources and Environment, Tsukuba (Japan)

1997-05-27

With an objective to detect gas leaking from an underground gas pipeline, discussions have been given on a method which utilizes acoustic characteristics of leakage. On leaking sound generated from damaged portions, the form of damaging was hypothesized as pinholes, and spectra of leaking sounds from holes with different diameters were measured. The dominant frequency decreases as the hole diameter increases, while it is in a region of relatively high frequency of 1 kHz or higher. However, detection from the ground surface was impossible when cover soil has thickness from 0.5 to 1.5 m. In an experiment to measure leaking sound inside the pipe, pressure in the pipe was adjusted to 0.02 atm which is a standard pressure for a low-pressure pipe, and the sound was measured when the hole diameters were varied. In any of the results obtained by varying the hole diameter, spectra having the dominant frequency in the region of 1 kHz or higher were measured. In addition, it was found that sound pressure difference of as much as 50 dB at maximum is generated as compared with a case of no sound leakage. The above results verified that monitoring the high frequency of 1 kHz or higher is effective in detecting leakage from small damages. 2 refs., 4 figs.

Report on surveys and researches to excavate international joint researches related to industrial technologies; Sangyo gijutsu ni kansuru kokusai kyodo kenkyu hakkutsu no tame no chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Five themes were taken up for a project of the 'surveys and researches to excavate international joint researches related to industrial technologies'. Investigation groups were organized and dispatched for each theme toperform domestic and overseas surveys. Discussions were given on eachtheme for the possibilities of structuring international joint researches. The five themes are as follows: 'wearable information network related technologies', wherein technologies to micronize information devices have been advanced rapidly, and the technologies are entering the age from personalizing and mobilizing the information into the wearable computing; this theme is intended to develop systems to unify these technologies by means of international joint researches: 'surveys on using unutilized animal oils and fats as chemical raw materials', which are intended to make clear possibilities and problems in utilizing animal oils and fats as raw materials for the chemical industry that can substitute fossil resources: 'international joint researches on new glasses' and 'processes to manufacture semiconductors using glassy carbon' to develop glassy carbon having excellent chemical resistance substituting quartz: and 'international joint researches on the Russian project which places environment and energy in its center'. (NEDO)

Report for fiscal 1998. Joint research of environment-friendly system for effectively utilizing water resources; 1998 nendo hokokusho. Kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The research is conducted in cooperation with Industrial Technology Development Institute of the Philippines, and aims to solve water related problems such as unstable water supply and water quality pollution though developing a waste water treatment and recycling system which is easy to operate and maintain, low in cost, and usable in the Philippines. Fiscal 1998 is the second year of the project. Statistics are studied about the load that each industrial branch imposes on water for its pollution, and it is found that food manufacturers, paper pulp mills, and fiber dyeing plants are heavily responsible for water pollution. A method consisting of single-tower UASB anaerobic treatment and activated sludge treatment is applied as a water treatment process to Ram Food Products Corporation, and its optimization is studied. A removal rate 60% is achieved after a 12-hour treatment period at a COD (chemical oxygen demand) rate of 8g/liter/day. A method consisting of coagulating sedimentation and activated sludge treatment is applied to the waste water from a Solid Mill Corporation dyeing plant, when it is found that the water after ultimate treatment is almost colorless and that COD is 76mg/liter and BOD (biological oxygen demand) 13mg/liter, and these suggest that the waste water is recyclable. Since it is low in COD removing rate, the application of anaerobic treatment to high-concentration water after washing is not appropriate. (NEDO)

Investigational study on the development, production and wide spread of welfare apparatus in north Europe; Hokuo ni okeru fukushi yogu no kaihatsu seisan fukyu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of grasping the present situation of the development/production/spread of welfare apparatus in north Europe, an investigation was conducted paying visits to Sweden and Denmark. Basically in the Swedish policy for handicapped persons, disablement is defined not only as features which belong to each individual, but as problems arising when the environment surrounding each individual touches one another. Moreover, characteristics of their policies on welfare apparatus are that major welfare apparatus can be provided for the disabled free of charge, and that the government and public organs play a major role in each step of the development, evaluation, distribution and provision of welfare apparatus. Features of the market of welfare apparatus are that users and buyers of the apparatus are different persons, that a public corporation called SUB participates in determining selling prices, etc., and that the market reflects needs and requests from users comparatively naturally. The needs for welfare apparatus at the Research Institute of Handicapped Persons are grasped through opinion exchanges with groups of handicapped persons or information exchanges with the technical aid center. 3 refs., 11 figs., 10 tabs.

Study on characteristics of response to nodal vibration in a main hull of a large-size ferry boat; Ogata feri no shusentai yodo oto tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Takimoto, T; Yamamoto, A; Kasuda, T; Yanagi, K [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

1996-04-10

Demand for reduction in vibration and noise in large-size ferry boats has been severer in recent years. On the other hand, vibration exciting force in main engines and propellers is on an increasing trend in association with increase in speed and horsepower. A large-size ferry boat uses an intermediate-speed diesel engine which has high vibration exciting frequency. Therefore, discussions were given on characteristics of response to nodal vibration in a main hull induced by primary internal moment in a main engine in a large-size ferry boat mounting an intermediate speed main engine. Results of detailed vibration calculations, vibration experiments using an actual ship, and results of measurements were used for the discussions. Natural frequency for two-node vibration above and below the main hull was set for an equation of estimation such that the whole ship is hypothesized to have been structured with beams having the same cross section according to the Todd`s equation, and effect of rigidity of the long structure can be evaluated. Parameters were derived by using the minimum square method that uses the measured natural frequency of the ship A through the ship E among large-size ferry boats. The derived result may be summarized as follows: this equation of estimation has an estimation error of about 5% against the natural frequency for nodal vibration above and below the main hull; and this equation of estimation has an estimation error of about 30% against the acceleration in the vertical direction at the end of the stern. 2 refs., 11 figs., 1 tab.

Fiscal 1999 survey report. Survey of leading countries' approaches to biomass energy development; 1999 nendo shuyokoku ni okeru biomass energy kaihatsu eno torikumi ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The survey aims to help Japan deliberate its future biomass energy development strategy including the course Japan is to follow in its research and development of biomass energy by clarifying leading countries' approaches to the subject matter and trends of their research and development efforts in this connection. The states of biomass energy development in the U.S. and Europe are reported. In the U.S., President Clinton issued Executive Order 13134 on August 12, 1999, regarding bio-based products and bioenergy development. In this country, bioenergy and bio-based production technologies have developed to reach a stage where business pays, and commercial plants are in service. The U.S. Administration mentions as a strategy the efficient development of the bioenergy industry. In Europe, where resources are versatile and local, it is difficult to assess the economy of scale, and small-scale development efforts are being accumulated. Practical technologies under development mostly involve direct combustion. European measures are similar to U.S. measures in that such political goals as local development and employment promotion are firmly woven into them. (NEDO)

Characteristic analysis on the deformation behaviour of shell-like lattice structures subjected to follower forces; Judo kaju wo ukeru kosa arch kozo no daihenkei kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fukuchi, N.; Okada, K. [Kyushu University, Fukuoka (Japan); Fujii, M. [Namura Shipbuilding Co. Ltd., Osaka (Japan); Shiraki, M. [Toyota Motor Corp., Aichi (Japan)

1998-09-04

The deformation mechanisms of submerged shell-like lattice structures with membrane are in principle of a non-conservative nature since the follower type hydrostatic pressure. In the region of large deformations, especially in the case of geometrically deep shell-like lattice structures, the system could be much more accurately defined in a mono-clinically convected coordinate description than the conventional spatial description. Also, a complete analysis of a non-conservative system requires a criterion since the system can have multiple ranges of stability and instability involving buckling and snapping. This paper presents the development of the governing equations for the finite deformations of shell-like lattices defined in a mono-clincally convected coordinate description and applies the same to different cases of lattice deformations. The validity of the formulations is verified for finite deformation. The examples of some geometrically special shell-like lattice structures are presented as well to show the feasibility of the present formulation. 5 refs., 11 figs.

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

Report on the research achievements in the Sunshine Project in fiscal 1992. Studies on a direct gasification catalyst; 1992 nendo chokusetsu ekika shokubai ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-10-01

This paper describes the research achievements in the Sunshine Project in fiscal 1992 in studies on a direct gasification catalyst. The paper summarizes the points where the catalyst research has reached to date. The catalyst surface effective for hydrogenation is the metal surface that can dissociate hydrogen. However, metals having large adsorption heat against hydrogen do not show the activity greatly because these metals are difficult of desorbing hydrogen having high dissociating activity. The coal liquefaction system has the surface oxidized by water content, wherein hydrogen dissociation cannot be expected, and sulfides are suitable. When a sulfide catalyst contacts hydrogen, the catalyst itself is desulfurized, producing H{sub 2}S and becomes a low-order sulfide. When atmospheric H{sub 2}S contacts this sulfide, it dissociates into HS and H, and this H behaves as active hydrogen. However, the liquefaction activity can be recognized even in a sulfuric acid type catalyst containing no sulfide whatsoever, wherein the H{sub 2}S partial pressure in the reaction system becomes extremely low. This fact means that the active hydrogen is not necessarily generated by the dissociation of H{sub 2}S. There is no other way but to think that hydrogen is dissociated directly without going through H{sub 2}S. If this is true, it provides a new guideline in developing and designing the future catalysts. (NEDO)

Report on achievements in fiscal 1975 in Sunshine Project. Studies on a technology to measure inside of wells; 1975 nendo koseinai sokutei gijutsu ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

In order to identify the actual status of geothermal reservoirs, development is made on a technology to detect cracks in a geothermal reservoir. This fiscal year has launched development of a PS sonic logging device of well wall compression type, which is considered most effective in crack detection. This device has a number of new development elements such as a mechanism to have a transmitter and a receiver compressed on a geologic stratum to send sonic energy directly into the stratum, simultaneous use of S-wave having excellent characteristics in evaluating crack faces quantitatively and calculating porosities, and a cooling mechanism for electronics installed in the wells. Combining this with a micro seismogram log scheduled to be fabricated in fiscal 1976 will form the mainstream of crack face detection. A continual flow meter measures behavior of steam and hot water to identify flow-out or flow-in patterns and depths of fluid in wells under flowing condition. Adding this meter to temperature and pressure elements scheduled to be developed in fiscal 1976 will provide data to give an important guideline in underground heat production. This meter was attempted with enhancement in heat and pressure resistant characteristics and stabilization of operation for design and fabrication, which were carried out using the spinner flow meter as the base. (NEDO)

Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

Survey and research on the effects of technological development. Annex (Tables of technology-related data); Gijutsu kaihatsu no koka ni kansuru chosa kenkyu. Bessatsu (gijutsu kanren data list)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Compiled into a report are the data about trends in Japan's research and development efforts broken down by industry covering a period of 1960-1980. The data items are quite versatile, including the number of companies engaged in researches and their rates, number of employees, total sales volume, profits through business, number of employees related to researches, number of dedicated researchers, number of dedicated researchers per 10,000 employees, disbursement of in-house research expenses, rate of personnel expenses to in-house research expenses, rate of disbursement of in-house research expenses to total sales volume, rate of disbursement of in-house research expenses to profits through business, disbursement of in-house research expenses per company, disbursement of in-house research expenses per dedicated researcher, in-house research expenses broken down by purpose (basic research, applied research, research for development), component ratio (basic research, applied research, research for development), number of dedicated researchers per speciality (total number, mathematics and physics, chemistry, biology, geology, engineering, civil engineering and construction, machinery and ship and aviation, electricity and communication, mining and metallurgy, textile, agriculture and forestry, fishery, stock-breeding and veterinarian, medicine and dentistry, pharmacy), number of technologies exported, total sum of export, etc. (NEDO)

Experimental and analytical study on internal resonances in a cable-stayed beam model. Cableter dot hari model wo mochiita shachokyo no naibu kyoshin ni kansuru jikken to kaiseki

Energy Technology Data Exchange (ETDEWEB)

Fujino, Y.; Warnitchai, P.; Pacheco, B. (The University of Tokyo, Tokyo (Japan). Faculty of Engineering)

1991-07-15

This paper examines the dynamic characteristics on the model of the beam supported by one cable, the most simple type of cable-stayed bridge, with fundamental and important linear and nonlinear internal resonances from the experimental and analytical aspects. Vertical oscillation of the beam is able to cause parametric oscillation of the cable, so that dynamic phenomena which derive from internal resonance such as saturation of amplitude of vertical oscilation of the beam are observed experimentally. Based on the concept of local and global oscillation modes, a 3-DOF(degree of freedom) model is formulated considering the geometric nonlinearity of the cable. Then, a test of a small model, taking notice of linear compound of the cable and the beam as well as autoparametric compound by quadratic nonlinear terms, is conducted under vertical and horizontal harmonic excitations. After identifying the parameter of the model, the experimental value is compared with the analytical value. As a result, it is shown that both of them are highly consistent with each other. 16 refs., 9 figs., 2 tabs.

Effect of mixture formation process of premixed lean diesel combustion. Study of the effect of mixture homogeneity on premixed lean diesel combustion in aid of numerical simulation; Yokongo diesel nensho ni okeru kongoki keisei katei no eikyo. Kongoki no kin`itsusei no eikyo to suchi simulation ni yoru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Shimazaki, N; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

NOx emission was extremely decreased by PREDIC (PREmixed lean DIesel Combustion) in which fuel was injected at very early stage of compression stroke and the combustion started at near the TDC by self ignition. We have considered that NOx reduction is caused the decrease of a region of stoichiometric mixture ratio by means of extremely early injection. Therefore the homogeneity is very important to decrease of NOx. In this study to investigate the effect of mixture homogeneity in the PREDIC, gaseous fuels (DME, CH4) were charged into the intake, by the combination of direct fuel injection, the mixture heterogeneity was positively changed. In addition the mixture formation process is shown in aid of numerical simulation, it is observed that the homogeneous has the advantage of low NOx emission in PREDIC region. 9 refs., 10 figs., 1 tab.

FY 1974 Report on results of Sunshine Project. Feasibility study on techniques for measurement of conditions within geothermal wells; 1974 nendo chinetsu koseinai sokutei gijutsu ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

This report covers the principles and methods of various bed-detecting techniques and their application, to begin with, current status of these techniques, results of feasibility studies on system data processing, well mouth analyzing systems, how to develop techniques for detecting geothermal beds, bed-detecting systems and environment-simulating devices, and finally conclusions, for the subject research and development project. The detecting techniques used for the geothermal area include those based on electrical properties, temperature, pressure and flow rate, analysis of core and fluids collected by analyzing systems at the well mouths, and detection of H{sub 2}S gas. Evaluation of geothermal reservoirs needs the data of absolute temperature of the geothermal sources, quantities of vapors spouting out of the wells, depth of boiling planes and pressure; and other basic data, e.g., void volumes of broad sense, quantitative evaluation results of cracks, shapes of naked well walls, expansion of reservoirs relative to bed, and effective bed thickness, which are determined by bed-detecting techniques for physical properties. It is necessary to develop the bed-detection systems adequately covering bed-detection items, detection of production beds for geothermal measurement, other bed-detection systems, and heat-resistant wire line cables and other cables serviceable at high temperature, as the essential items for obtaining the above data. (NEDO)

Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

Fiscal 2000 survey report. Research on bone-forming dental material capable of reducing plaque adhesion; 2000 nendo shiko fuchaku boshigata hone keisei shika zairyo ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development efforts are exerted to produce advanced dental materials equipped with such functions as plaque reduction, bactericidal effect, and early formation of hydroxyapatite (HAP). In the study of fluorine ion implantation for plaque reduction, it is found that in a specimen implanted with fluorine ions the adhesion of carius streptococci is reduced to 1/3-1/10 for the achievement of remarkable improvement. In particular, carious streptococcus multiplication is suppressed when the metal shield layer is replaced with a titanium mesh. For the realization of a thin film formation method for osteoblast multiplication through reforming the material surface in the study of bone-forming dental materials, film formation conditions under which a P/Ca rate which is quite near that of ameloblast are achieved by use of a high frequency magnetron sputtering device. A titanium plate coated with a thus-formed film is annealed for a great increase in its wet contact angle, and then adhesion of bacteria is reduced and an osteoblast multiplication rate is increased by 20% or more, as compared with the case of no treatment in a petri dish. (NEDO)

Fiscal 1998 research report. Survey on the current trend of private R and D efforts; 1998 nendo chosa hokokusho. Minkan no kenkyu kaihatsu doko no jittai ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For promotion of the R and D system of technologies creating new industries, this survey collected the basic data and information on the trend of private R and D efforts and industries, and arranged every data and information obtained. The data on United States, Germany, France and U.K. in addition to Japan were collected. Survey was made first on the administrative support system for private R and D efforts. The R and D-related budget, R and D support program and private R and D-related fund of Japan, United States and U.K. are mainly outlined. Survey was made next on private R and D activities. The R and D-related fund, researcher and patent of main countries are outlined in international comparison. Survey was also made on the current state of various industries. The industry scale and structure of every Japanese manufacturing industry are outlined. Finally, the industrial statistics are given concerning Japanese 'chemical industry,' 'communication-electronics-electric measuring instrument industry' and 'automobile industry' with a high rate of R and D-related expenditures. (NEDO)

Report on achievements in fiscal 1974 in Sunshine Project. Study on hot water systems in geothermal areas; 1974 nendo chinetsu chiiki no netsusuikei ni kansuru kenkyu seika chukan hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This study has begun in fiscal 1973 under a five year plan with an objective to elucidate origin and maintenance of reservoirs of geothermal fluids. To achieve the objective, estimation was made on the systems of infiltration, storage and gushing of the fluids, particularly on infiltration areas. In the hydraulic flow rate study, observation was carried out in the Onikubi area on amount of rainfall, air pressures, temperatures, electric conductivity, and pH, and in ten fluid sources on flow rates, temperatures and pH. Flow rate observation was started at three rivers. In the Kuju area, flow rate observation was started on four fluid sources. Observations were started on temperatures, electric conductivity, flow rates, amount of rainfall by using the Takenoyu geothermal steal wells, and on amount of rainfall in the Teraono and Hacchobara areas. In the study of isotopic geology, site analyses and water collection were carried out in the Kuju area for underground water in six locations, hot spring water in seven locations, and 17 test samples from two geothermal wells. As a study on reservoirs, observation was started in the southern Hachimantai area on measurement of ground fluctuation in association with steam collection. In parallel, fracture survey and gravity measurement were carried out. In order to investigate transformed geology, analytic samples were collected from 12 survey wells in the Onikubi area. A spinner flow mater was tested in that area. (NEDO)

Fiscal 1975 Sunshine Project research report. Research on safety technology for hydrogen energy systems; 1975 nendo suiso energy system ni okeru hoan gijutsu ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-05-01

Important notices and problems on the safety for hydrogen gas were analyzed. Analysis was made on hydrogen gas property, flammability, explosivility, bio-toxicity, equipment, storage, transport, leakage, fire, technology and education for safety management, and quality and analysis of products. Study was also made on the relation between the above items and every domestic or overseas standard. Important notices and problems on the safety for liquid hydrogen were analyzed. Analysis was made on liquid hydrogen property, liquefaction and refining equipment, transport, storage, materials concerned, bio-toxicity, leakage, fire fighting technique, and safety management. Among them, such problems are pointed out from the viewpoint of accident prevention, as O-P conversion, refining of hydrogen gas for liquefaction, selection of structural materials, hydrogen embrittlement, layout of various equipment and devices, explosion-proof electric devices, and leakage detection. Research on effective fire fighting and fire preventive measures against hydrogen leakage and diffusion from tanks or piping are also in demand. (NEDO)

Survey of the measures to be concretely taken for CEV introduction/spread in the region; Chiiki ni okeru CEV donyu fukyu no tame no gutaiteki hosaku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the Hanshin/Harima region where CEV introduction/spread are expected and there is a great pervasive effect, survey/study were conducted to plan the construction of facilities for natural gas vehicle fuel supply in future. In the survey, the paper summed up the state of CEV spread in the Hyogo prefecture, the state of construction of fuel supply facilities, etc. Further, by the questionnaire survey, the needs for construction of fuel supply facilities were grasped, and the intention of introducing natural gas vehicle was sounded out. In the study of a wide-area construction plan for natural gas fuel supply facilities, the Hanshin/Harima region was divided into zones based on geographical conditions, traffic system, etc., and the number of the needed fuel supply facilities was calculated which corresponds to the targeted number of natural gas vehicle introduction set up by the nation. Moreover, by the questionnaire survey, the needs for fuel supply facilities were grasped, and a method for setting up the order of priority in the construction was determined/proposed. Through the study of these, a manual was made out which is usable for the CEV introduction and the construction plan for natural gas fuel supply facilities in other regions. (NEDO)

Investigations on sail force by full scale measurement and numerical calculation. Part 1. Steady sailing performance; Sail ryutairyoku ni kansuru jissen shiken to suchi keisan. 1. Teijo hanso seino

Energy Technology Data Exchange (ETDEWEB)

Masuyama, Y.; Fukasawa, T. [Kanazawa Institute of Technology, Ishikawa (Japan); Kitazaki, T. [DMW Corp., Tokyo (Japan)

1997-06-01

Sailing forces are measured with a 10.3m long full-scale sailing boat, equipped with a sail force dynamometer, CCD camera for sail shape measurement and an instrument for detecting sailing conditions of the hull, in order to obtain highly reliable performance data of a sailing yacht. The vortex lattice method is used for step-by-step numerical calculations, and the results are compared with the observed ones. The test results clearly show performance changing with slight changes in relative wind directions and sail shapes, which are not clearly obtained by the traditional wind tunnel tests. The calculated results, although deviating from the observed ones to some extent, well represent trends of performance changing with wind directions and sail shapes. In particular, changed performance caused by slight changes in draft at the main sail is clearly demonstrated. The numerical calculation is considered to be useful for searching for sail trim conditions. 17 refs., 18 figs., 1 tab.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

Study on high concentration solar concentrator using a Fresnel lens with a secondary concentrator; Fresnel lens to niji shukokei wo mochiita solar chemistry yo kobairitsu shukokei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aihara, T; Suzuki, A; Fujibayashi, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

A high concentration light collection system for solar chemistry was devised by using an inexpensive Fresnel lens in a primary concentration system and a conical type concentrator in a secondary concentration system. A Fresnel lens alone would not achieve sufficiently high light collecting magnification to attain high temperatures because of restrictions in the opening angle as seen from a focus. Therefore, a secondary concentration system was installed on a focus for an attempt of stopping. Reflection plane of a three-dimensional compound parabolic concentrator (CPC) is a rotary parabolic plane, whose process is expensive because of its surface processing accuracy. Therefore, a conical type concentrator was employed as a secondary concentration system. This system may not be capable of achieving as high concentration as in the CPC, but its shape is simple and it is inexpensive. In its optimization, a complete black body surface placed in vacuum atmosphere was hypothesized as a light concentrating part for the secondary concentration system to calculate heat collecting efficiencies at respective temperature settings. Using simultaneously the secondary concentration system, rather than collecting heat by using a Fresnel lens alone, has attained as high value as from 5.99% (500 degC) to 43.47% (1400 degC). Economical high-temperature heat collection of solar chemistry level may be possible by using a Fresnel lens and a conical secondary concentration system. 1 ref., 7 figs., 2 tabs.

FY 1994 report on the cooperative research on the biological use mine wastewater treatment technology; 1994 nendo bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In this project, a pilot plant for mine wastewater treatment facilities using Thiobacillus ferrooxidans was installed at the Wushan mine in China to study the operation using the bacteria habitable in this mine. The project aims at establishing the mine wastewater treatment technology using the method of Thiobacillus ferrooxidans in China. The field survey and study in Japan were carried out. In the field survey, the technical guidance was given for incubation method, neutralization experiment method and analysis method of Thiobacillus ferrooxidans. In the study in Japan, one kind of bacteria to be used was selected in the 'selection test for the optimum kind of bacteria,' and a study was made which was titled 'Study of mine wastewater treatment using the method of Thiobacillus ferrooxidans which is suitable for the mine site.' In 'Study of the optimum removal of heavy metal in mine wastewater,' a table test of sulfide precipitation method was conducted on copper removal/recovery to make formation conditions of copper sulfide clear. The conditions obtained were reflected in 'Study of mine wastewater treatment by the method of Thiobacillus ferrooxidans which is suitable for the mine site,' and various conditions for bacteria oxidation process were studied. The paper surveyed characteristics of heavy metal and temperature of Chinese strains. Further, the basic data were acquired which contribute to the production of inorganic flocculants. (NEDO)

Achievement report for fiscal 1993 on research under Sunshine Program. Research on direct liquefaction reaction of coal; 1993 nendo sekitan no chokusetsu ekika hanno ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The reaction velocity constant of coal or the distribution of products in a high-pressure hydrocracking process of coal are found not to be affected by the temperature rise rate. The liquefaction of coal using CO and water is analyzed using a high-pressure differential thermal analyzer. The hydrogen gas generated during the water gas reaction reacts with CO for the formation of alcohols, carbonic acid, etc. The reaction rate is found to be higher when the specimen contains more oxygen. When coals greatly different from each other in terms of thermolytic reactivity, caking property, and intersolubility with medium oils are mixed, synergistic effects are exhibited, positive when active hydrogen supply is abundant and negative when it is short. In the case of the Hokkaido coal which contains 73.0-87.4% carbon, the grain diameter does not affect the liquefaction rate when the coal is crushed to the 48-mesh size approximately. Reaction velocity in direct liquefaction does not relate to hydrogen pressure. Asphaltenes in coal liquefaction are produced at the beginning of reaction, to be reduced in molecular weight due to cleavage of methylene crosslinks with the progress of reaction. Studies are conducted in a 0.1t/d-capable bench plant about liquefaction reaction characteristics and coal liquid properties, and chemical structures. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1976. Research related to hydrogen combustion technologies; 1976 nendo suiso nensho gijutsu ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

Regarding the Sunshine Project, this paper describes characteristics and technologies of hydrogen combustion, problems in developing combustion devices and conceptual design thereof, catalytic combustion, hydrogen energy systems, and economic evaluation on hydrogen fuel as a heating energy. Hydrogen combustion could emit small amount of NOx if it is sufficiently pre-mixed with air, but at the same time could cause reverse ignition very easily making its practical use difficult. Abolishing the air pre-mixture would cause no fear of reverse ignition, but generate much more NOx than from hydrocarbon fuels. Even if attempting to apply conventional methods such as two-stage combustion, partial stack gas recirculation, water addition, and lean burn systems, many of them cannot be applied as they are, requiring research and development efforts. Discussions on hydrogen energy as a system included those on thermo-chemical hydrogen manufacturing using heat from high temperature gas reactors (using water as the raw material), and electrolytic hydrogen gas manufacturing utilizing surplus electric power from high speed breeder reactors. Whether these methods could be used in markets economically will depend on manufacturing efficiency and cost of hydrogen gas. As the economic evaluation on hydrogen as fuel, discussions and considerations were given on introduction priority in the industrial heating furnace field. (NEDO)

Investigations and researches on CO2 balance in a high-temperature carbon dioxide separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With an objective to select a promising process by comparing application environments and effectiveness of a high-temperature carbon dioxide separation, recovery and re-utilization technology with other methods, investigations were performed on reducible amount of carbon dioxide discharge by using material balance and system introduction. A large number of chemical and physical technologies are being developed for the separation and refining methods. This paper discusses the technologies for their application to iron and steel making, oil refining, and petrochemical industries, the so-called heavy and large product industries. As a possibility of utilizing the high-temperature separated CO2 in iron and steel making, an investigation was given on the direct iron ore smelting reduction process. It would be unreasonable to use CO2 in oil refining as a substitute to air to regenerate a catalytic decomposition and reformation catalyst because of decline in the catalytic activity. A discussion was given on a case to replace steam with CO2 in steam reformation and pyrolysis of hydrocarbons. The discussion requires the objective to be focused on such items as C/H ratio at a reformer outlet and relationship of balance in decomposition products. The C1 chemical and others were reviewed to search possibilities for their use as raw materials of chemicals used in chemical industries. Possibilities were discussed to fix high-temperature CO2 into peridotite and serpentine. 42 refs., 32 figs., 11 tabs.

Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

FY 1997 report on the study on development of corrosion-resistant ceramics for refuse incinerators; 1997 nendo chosa hokokusho (gomi shokyakuroyo taishoku ceramics zairyo no kaihatsu ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes development of structural materials for municipal refuse incinerators, in particular, high- temperature corrosion-resistant ceramics for inner walls. Unlike boiler tubes of which inner walls are cooled by water or water vapor, refractory for inner walls is subjected to high-temperature flame over 1000degC, corrosive gases such as HCl and SO2. and low-melting point corrosive dust such as chloride, sulfate and oxide under strong corrosive environment. Experiment was made on 14 kinds of ceramics including commercially available oxide system, non-oxide system and refractory system ceramics. Except graphite system ones, every ceramics, in particular, Al2O3, ZrO2, B4C-doped SiC and CVD-SiO showed superior properties. Commercially available ceramics, in particular, non-oxide system ones are very expensive. Since inner wall materials for refuse incinerators are heat-/corrosion-resistant consumption articles, it is suggested that improvement of reasonable oxide system ceramics or conventional SiC system ones is better. 73 refs., 89 figs., 39 tabs.

Achievement report on the survey concerning possibility of expansion of ITS technology application to various mobility systems; Kakushu mobility system eno ITS gijutsu tekiyo kakudai kanosei ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to evaluate the results so far achieved in 'The research and development of ITS (intelligent transportation system) by use of clean energy vehicles' and 'Research and development of ITS technology assisted mobility systems' and the development systems under which the efforts are exerted and to evaluate the possibility of their practical application and the spread of the effects brought about. Ex post facto evaluation is conducted of two types of test systems. The first type includes a rent-a-car for business use in the urban area, a rent-a-car for sightseeing, and a system which is an ITS provided electric car as a domestic second car in the residential district. The second type includes a shuttle bus park-and-ride system and a natural gas fueled physical distribution truck. The result is that the ITS provided electric car system is evaluated high by evaluation committee members. The score lowers in the order of the system for business use in the urban area, the system for sightseeing, and the second car system in the residential district. An electric car reduces its environmental impact when it uses a power generation system that utilizes renewable energy. It has become clear that high convenience will be achieved when a dispatching system is improved for a combination of a 'subminiature electric vehicle and ITS technology' as a method to satisfy the demand for commutation means in case the clientele is one or two people. (NEDO)

Fiscal 1994 report on the survey of making models for introducing petroleum substituting energy systems; 1994 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. appropriate and concrete guidance for introducing energy systems which meet with features of the areas and buildings and courses for how to construct infrastructures of towns or cities in case of development and redevelopment. Recently, also in local governments, etc., there are seen attitudes toward positive study of introduction of energy conservation systems and petroleum substituting energy systems in case of redevelopment, and the situation is that the spread and expansion are expected by giving appropriate guidance for the introduction. Accordingly, the study makes analyses of the trend and characteristics of developmental projects and makes/arranges models of promising petroleum substituting energy systems, aiming at contributing to promotion of guidance for the introduction to local governments, entrepreneurs, etc. Approximately 20 models of petroleum substituting energy systems were made which are thought to be promising. For each, the following were arranged: outline of system, introduction target, introduction effects, the point of promotion of the introduction, related subsidy systems, actual results, etc. 22 figs., 34 tabs.

Fiscal 1998 research report on the basic research on the practical application of innovative technologies. 2; 1998 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report is composed of the part 1 'Estimation of fossil energy resources and preliminary preparation of the super- long-term view of energy supply and demand', and the part 2 'Research on concrete conditions for introducing renewable energy (RES)'. In the part 1, estimation was made on the amount of non-conventional fossil energy resources such as oil sand, oil shale, coal bed methane and methane hydrate. Study was also made on the role of nuclear power, fast breeder reactor and nuclear fusion in the world energy supply and demand in the 21st century. In addition, as preliminary study on the super-long-term view of energy supply and demand in the next fiscal year, study was made on a scenario and measuring model considering energy supply restriction and CO{sub 2} problem. In the part 2, research was made on the amount of resources, applicable fields and cost estimation for various RESs such as solar energy, wind power, biomass, oceanic energy, geothermal energy and hydraulic power. Several technical issues on transport, storage, conversion and use for every energy were arranged toward real introduction, efficient use and stable supply of such RESs. (NEDO)

FY 1998 annual summary report on recent trends of global warming prevention measures with fluorochlorohydrocarbon alternatives; 1998 nendo daitia furon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the recent trends of the ozone layer protection and global warming prevention measures. Latest international information has been collected by attending the 10th Meeting of the Party of Montreal Protocol, and the 17th and 18th Open Ended Working Group. The important decisions made so far are investigation on the novel ozone layer destruction substances, requirement of studying on decommissioning Halon facilities, collection of information of HFC and PFC, and reporting to IPCC. Information regarding regulation trends of HFC, PFC and SF{sub 6} are collected by attending the COP-4 meeting and the preparatory meetings therefor. The report on these 3 substances will be completed in July or so, 1999. The trends of technical development in HCFC alternatives in refrigeration and blowing sectors were investigated. HFC-245fa and HFC-365mfc are introduced. Also introduced is latest information regarding the emission estimation and control measures of HFC in USA and UK, emission control measures of SF{sub 6} in USA and Japan, and techniques for destruction of CFC and the like, which could be the basic techniques for controlling diffusion of HFC. The CFC phase-out programs of China, the biggest ozone layer destruction substance (e.g., CFC) consuming country, are also outlined. (NEDO)

Research cooperation project for fiscal 1999. Research cooperation on environment-compatible type water resource effective utilization system; 1999 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Efforts are made under this project to develop a wastewater treatment/regeneration system, easy to operate and maintain and low in cost, jointly with a Philippine research institute. Technologies are transferred to this institute concerning research and development, system designing, operation, maintenance, and management. The goal is to disseminate such technologies in the Philippines. As for fiscal 1999 endeavors, emphases are placed on the items described below. The Container Corporation which regenerates waste paper and the RAM Food Corporation which manufactures canned foods and pickles are selected as the sites for pilot plant research. Wastewater discharged by the two corporations is subjected to laboratory-scale wastewater treatment (combination of aerobic/anaerobic treatment and activated carbon adsorption), by which a pilot plant wastewater treatment process is determined and designing conditions are defined. As for activated carbon for advanced wastewater treatment, a fine grain sample, which is the lowest in price among activated coconut shell charcoals produced in the Philippines, is acquired, and tested for performance. A wastewater treatment pilot plant is complete at the Container Corporation, and has started operation. (NEDO)

Study on an optimum ratio of PV output energy to WG output energy in PV/WG hybrid system; Taiyoko/furyoku hybrid hatsuden system no saiteki yoryohi ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Nishikawa, S [Kandenko Co. Ltd., Tokyo (Japan)

1996-10-27

A photovoltaic power (PV) and wind generated power (WG) are an unlimited clean energy source, yet their output is unstable depending on the fluctuation of weather conditions such as solar radiation and wind velocity. Consequently, a large-scale power storage equipment is necessitated leading to a high cost especially in an independent system. As a solution, a method is available in which PV and WG are combined so that the effect may be utilized for stabilizing the output of a system as a whole, at a site where a fluctuation pattern is different between photovoltaic energy and wind energy. In building a hybrid system by PV and WG, sites with such supplementary effect existing were selected from the viewpoint of stabilizing the fluctuation of the power generation in the long run; and then, an examination was made on the optimum PV capacity ratio (%Ppo) in each site. As a result, it revealed that the %Ppo had great bearing on a ratio of PV energy fluctuation to WG, which was converted to a numerical formula. A comparatively simple examination by means of meteorological data also indicated that the share ratio was possibly optimized between the quantities of PV and WG energy. 4 refs., 2 figs., 2 tabs.

Estimation of the crack growth mechanism in the coking process. ; Behavior of fracture mechanics parameter. Cokes sonai kiretsu shinten ni kansuru ichikosatsu. ; Hakai rikigaku parameter no kyodo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Yoshino, H; Sato, H; Nogami, H; Miura, T [Tohoku University, Sendai (Japan). Faculty of Engineering

1991-07-10

Cracks generated in coke layers during a coking furnace operation are an important factor not only to decide quality of the product, but also govern the energy consumption affecting the heat transfer and material transfer. This paper describes estimations of thermal stress and observations to fracture mechanics parameters, applying the incremental theory to surface cracks seen in the initial stage of carbonization. As a result of calculations using the crack tip opening displacement (CTOD) as a parameter to evaluate displacement in the vicinity of crack tips, the values increased with the increasing heating rate, and agreed qualitatively with the trend found in the experiments. The CTOD relates closely to the temperature dependence of the contraction coefficient, and varies largely at the transition point from the first maximum point to the second maximum point, from which the surface cracks are predicted to have been generated in this temperature region. Also, an estimation was made on the stress expansion coefficient from the stress distribution, and a result that can explain the experimental resultswas obtained. 10 refs., 11 figs.

Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H; Seo, K; Yamanaka, H [Tokyo Institute of Technology, Tokyo (Japan)

1997-05-27

The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

Fiscal 1998 research cooperation project. Research cooperation on diversity preservation and sustainable use for living organisms; 1998 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report describes the titled research cooperation. Joint R and D with Thailand, Indonesia and Malaysia was made on collection and preservation of bio-resources such as tropical rain forest, and sustainable use of them by developing countries themselves. The project includes the simple identification and preservation technology of biospecies such as microorganism, assessment and monitoring technology of ecosystem, search of useful functions of biospecies, and construction of a bio-resource information network. This project promotes conversion of excessive hunting into resource conservation in agriculture, forestry and fisheries industries, and establishment of the basis of new product development in chemical and pharmaceutical industries. This project also contributes to preparation of the basic scheme of developed countries including Japan to countries holding bio-resources in addition to industrial basis preparation of every country. Until 1997, basis establishment has been made such as training of researchers, preparation of equipment and technical guidance, and in the final 1998, various results such as extraction of promising samples from microorganisms were obtained. (NEDO)

Enhancement of condensation heat transfer using electric field. Effects of wire-electrode coating; Denba ni yoru gyoshuku netsu dentatsu no sokushin ni kansuru kenkyu. Wire denkyoku no hifuku koka

Energy Technology Data Exchange (ETDEWEB)

Chu, R. [Gifu University, Gifu (Japan). Faculty of Enginering; Nishio, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Tanasawa, I. [Nihon University, Fukushima (Japan). College of Engineering

2000-08-25

In the present paper, an attempt is made to develop an effective EHD enhancement technique for condensation heat transfer of steam around a horizontal finned tube. The main idea in the present study is to reduce the power consumption by using a partially coated electrode, and the experimental data of heat transfer coefficients and flooding angles are presented. The result indicates that, by using such an electrode, the enhancement ratio keeps almost the same level with that of a bare electrode but the power consumption can be markedly decreased. Within the present experimental range, the condensation heat transfer coefficient on the finned tube with the partially coated electrode reaches a value about 3 times larger than that without electrode. In addition, a model in presented for the EHD effect on the flooding angle and it is confirmed that the prediction from the model is in good agreement with the experimental data. (author)

Manufacturing technology supported by advanced and integrated information system through international cooperation in fiscal 1995; Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Informatization using mainly computers is more and more important contributing to the upgrading in society, economy and a variety of fields. As to informatization in developing countries, however, there has still been few to be seen. Accordingly, gaps are getting larger between developing countries and developed countries where informatization is acceleratedly advanced. In the light of such actual state, Center of the International Cooperation for Computerization (CICC) contracted with NEDO and promoted a project `Manufacturing technology supported by advanced and integrated information system through international cooperation.` This is a project to study jointly with five Asian countries with which NEDO made a basic contract, China, Indonesia, Malaysia, Singapore and Thailand. Working group is set up for each theme such as automobiles/parts, electric home appliances/parts, and fiber/apparel, to study the construction of a model house and the design of a system. In fiscal 1994, the field survey was conducted, and in fiscal 1995 the system design was started. 16 figs., 1 tab.

Fiscal 1996 report on the investigational research on the construction of a database of physical functions; 1996 nendo chosa hokokusho (shintai kino database no kochiku ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of realizing `the affluence` sought in the Japanese economic society, the supply and preparation of products, service and environments friendly to human beings seem to be important. In the future, the development of products which are fully considered also of aged and handicapped people is more expected than the conventional manufacturing of products added with value. Especially in accordance with the rapid aging, from a viewpoint that the lowering of physical functions caused by aging has an exactly close relation with the response to products and the environment, development of the database of physical functions for the aged which is useful for the design is urgently promoted. First, the data to be supplied for database were selected. As to the selection method, the data required for database were defined by collection/analysis of the existing data, examination of the needs of enterprise designers, and analysis of daily activities. In the study of the database, the structure by which data can be effectively supplied was studied and verified by pilot database for extraction of the subjects and solution to the problems. 6 refs., 57 figs., 26 tabs.

Fiscal 2000 report of investigation. Part 2. Study on development of technology for reducing nitrous oxide; 2000 nendo asanka chisso teigen taisaku gijutsu kaihatsu ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the study focused on the possibility of technological breakthroughs, from the results of the survey on industrial technological trend and the preliminary examination concerning the technology for reducing nitrous oxide (N{sub 2}O), proposals were made on the direction of the future R and D. As technologies for reducing N{sub 2}O generation in the furnace, there are improvement of combustion process and development of high performance fluidized mediums. These are definite in their targets and methods, and are applicable as urgent countermeasures for immediate effects as well as highly reliable in the process of implementation. Meantime, as technologies for reducing N{sub 2}O in a flue gas by catalysts, there are decomposition or reduction of N{sub 2}O in the middle-temperature range (300-400 degrees C) and in the low-temperature range (lower than about 150 degrees C), suppression of N{sub 2}O as by-product generated in the NOx treatment process, and development of catalysts. These are applicable for a broad range of N{sub 2}O sources including automobiles. In addition, requiring no great modifications in the equipment infrastructure, these technologies will seem to spread immediately to a broad range of fields once an effective catalyst is developed. (NEDO)

Manufacturing technology supported by advanced and integrated information system through international cooperation in fiscal 1994; Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Among NEDO`s international research cooperation projects, the paper described Japan`s cooperation with Asian countries in development of an easy-operated electronic design/production supporting system. The project aims to realize information realtime technology by which data for design/manufacturing of machine/electronics/fiber/apparel can mutually be used among countries. For it, design data standard and electronic information exchange standard are developed. A production information integrated database system is developed for sharing processing data. Parts data are put into a library. Graphic user interface and multi-media technology are developed so as to comply with the environment of different usages. In fiscal 1994, emphasis of activities was placed on survey of the status quo of the institution of the party country, fermentation of mutual understanding, and study of a cooperative project plan. Memorandums on research cooperation were concluded with Indonesia, Malaysia, Singapore and Thailand. In addition, understanding of this project by the party country was able to be enhanced

Evaluation report on research and development of an ultra-advanced processing system. Sections 1 and 2; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 1 and 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-08-01

The ultra-advanced processing system is intended to develop an ultra-advanced processing device technology and an ultra-advanced processing technology. These technologies are indispensable to create such new processing technologies as ultra-precision and ultra-micro processing, and ultra high-grade surface modification processing, which have been impossible by the processing technologies having been available to date. It is also intended to develop a measuring and evaluating technology to support the above technologies. The intended system makes it possible to produce 21st century electronic components and ultra-high grade environment resistant materials. In order to achieve these goals, research and development has been performed on the excited beam technologies such as large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology to assure the reliability of these technologies as the fundamental technologies. This project has begun in fiscal 1986, where fiscal 1987 has achieved development of component technologies related to the large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology, and completed the device technology, having achieved the final target. (NEDO)

Study on the blasting demolition of steel construction. Part 2. Demolition work of steel tower; Tekkotsu kozobutsu no bakuha kaitai ni kansuru kenkyu. 2. Koro yagura happa kaitai koji

Energy Technology Data Exchange (ETDEWEB)

Ogata, Y.; Wada, Y.; Katsuyama, K. [National Institute for Resources and Environment, Tsukuba (Japan); Nishida, T.; Hoshino, M.; Nagano, M. [Kacoh Co. Ltd., Tokyo (Japan)

1997-06-30

This paper describes the blasting demolition of steel tower of iron works. The steel tower had four columns, and its dimension was 17 mtimes17 m in cross section and 77.6 m height. The total weight was about 1,724 t. The 18.4 kg V-type linear shaped charge was fixed around columns with box weld structures, and initiated using 16 seismograph electric detonators. Vibration and noise were measured during blasting and collapse of the tower. In the both case, the vibration levels were between 67 and 71 dB, which were low and under 75 dB, the standard level during specific construction works of the regulation act of vibration. The noise level was 120 dB(A) at the point 200 m away from the blasting source, which was over 85 dB(A), the standard level. The collapse process of steel tower was simulated using discontinuous deformation analysis. The results agreed well with those from the actual collapse. The steel tower landed about 6 seconds after the initiation, and it took about 15 seconds to complete the collapse. Before the demolition, the 6 t parts of forefeet of two columns in the collapse direction were cut and removed by blasting. Thus, the collapse was controlled in the given direction. 5 refs., 13 figs., 2 tabs.

Study on wave power generation of electricity using torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha wo mochiita haryoku hatsuden ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kojima, N; Kishimura, K [Meiji University, Tokyo (Japan)

1996-10-27

Windmilling characteristics of a combination of a torsion arc blade type (TABT) horizontal axis wind turbine and a reverse torsion arc blade type (RTABT) horizontal axis wind turbine were evaluated in a wave activated power generation experiment. The TABT wind turbine had six blades, and the front and rear parts of the blade were twisted in the same direction, which caused the direction of rotor rotation to change as the direction of wind along the shaft changed. The RTABT wind turbine had twelve blades, and the front and rear parts of the blade were twisted reverse to each other, which allowed the direction of rotor rotation to stay constant even in the presence of wind direction reversal. To keep the direction of rotor rotation unchanged in the presence of flow direction reversal along the power generating turbine shaft, a single-stage type RTABT wind turbine and a double-stage type were used, the double-stage type being a series connection of a first-stage RTABT (for blowout and suction) and second-stage TABT (for blowout only). Both single-type and double-type rotated in the same direction irrespective of the direction of air flow. The output of the double type was obtained by adding up the values obtained from the individual turbines. The double type was two to three times higher in efficiency than the single type in turbine revolution and power output. 2 refs., 13 figs.

Report on achievements in fiscal 1975 in Sunshine Project. Feasibility study on a volcanic electric power generation system; 1975 nendo kazan hatsuden hoshiki ni kansuru feasibility study seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

The survey and study activities in the second year for the feasibility study (FS) on a volcanic electric power generation system consist of the following three parts: Part I, the case study on Satsuma Iojima Island, Part II, case study on Toyohane Mine, and Part III, FS on remote measurement of volcanic fume. The Part I, which has been performed subsequently from the previous fiscal year, has carried out the following surveys at different sites: meteorological, hydrological and underground water surveys, natural earthquake survey, fume and hot spring surveys (on-shore and off-shore), heat dissipation survey, tide level survey, underground structure survey (electric exploration), natural environment (vegetation) survey, thermal image survey, and social environment survey. The part II has begun surveys starting this fiscal year, because a considerable number of high temperature portions are already known to exist in the gallery, where there is a possibility of dry and hot rocks to exist without relationship with the present volcanic activities. This fiscal year has carried out mainly putting into order and analyzing the materials having been obtained in association with mine developments. The part III has been performed succeeding the 'FS on technologies to measure volcanic fume energy' done by the Japan Mining Industry Association. Some experiments were also executed at the Aso volcano. (NEDO)

FY1995 study of highly efficient power generation system based on chemical-looping combustion; 1995 nendo chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Synthesis of highly efficient and low emission power generation plant with chemical-looping combustion using various fuels such as natural gas, coal gas and hydrogen. Development of new looping materials with suitable reactivity, regenerative ability, and avoidance of carbon deposition. To obtain the design data for demo-plant by using the current experiment high- pressure fixed bed reactor. From the viewpoint of application of the proposed power generation system with chemical-looping combustion, the following main results were obtained. 1. New looping materials: NiO/NiAl{sub 2}O{sub 4}, CoO-NiO/YSZ, and Co{sub 3}O{sub 4}/CoAl{sub 2}O{sub 4}. These materials have high reactivity, repeatability, and avoidance of carbon deposition which play important roles in application of this new combustor. 2. NO{sub x} formation can be completely avoided; both fuel NO{sub x} in reduction reactor for coal gas as fuel and thermal NO{sub x} in oxidation reactor. 3. It is identified from the experiment using fixed bed reactor with the elevated pressure that NiO/NiAl{sub 2}O{sub 4} is a suitable material for coal gas or hydrogen. These promising results have provided valuable data for industrial application. (NEDO)

Preliminary research on the activities implemented jointly (AIJ) workshop. Present AIJ in China; Kyodo jisshi katsudo workshop ni kansuru jizen chosa. Chugoku ni okeru kyodo jisshi katsudo no genjo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In order to positively promote the activities implemented jointly (AIJ) of the United Nations Framework Convention on Climate Change, the AIJ workshop acting in contact with Asia/Pacific countries, in particular, Chine having large effect on global environmental pollution was researched preliminarily. AIJ approved in the convention is the effective means to promote measures against global warming cost-effectively by optimally combining every developed country`s technology, know-how and fund. Distribution of the credit for greenhouse gas emission reduction by AIJ is unsolved because of the disagreement of views between developed and developing countries. The pilot phase of AIJ projects is carried out by voluntary workers jointly with developing countries until establishment of international rules. In fiscal 1995, the following were studied: the framework necessary for AIJ between Japan and China, the organization for promoting concrete AIJ projects, and the means to create the reliance of China for AIJ projects. 6 refs., 10 figs.

Study of selective oxidation of methane catalyzed by solid superacid in unique reaction field; Tokushu hannoba no kotai chokyosan wo mochiiru methane no sentaku sanka hanno ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Misonoo, M; Tatsumi, T; Mizuno, T; Inumaru, T [The University of Tokyo, Tokyo (Japan)

1997-02-01

Selective oxidation of lower alkanes by use of heteropolymeric compounds is studied. Alkanes are activated on Cs2.5H0.5PW12O40 serving as catalyst, and their activity and selectivity improve when the catalyst is developed into a dual function catalyst in which Cs and Pt are combined. A success is reported of the synthesis of a heteropolymeric acid in which two molecules of the coordination element wolfram are replaced with a transition metal of the first period, on which acid the oxidation of cyclohexane is enhanced. Cs2.5Ni0.08H1.34PVMo11O40 as a metal/heteropolymeric acid dual function catalyst enables the direct oxidation (9% recovered at 340{degree}C) of isobutane into a methacrylic acid, which is attributed to the harmonious coordination of the oxidizing work of the catalyst and acidity. It is possible to oxidize propane into the acrylic acid, but not ethane into the acetic acid. In the case of Pd/Cs2.5H1.5PVMo11O40, the formic acid, methanol, etc., are produced upon addition of hydrogen to the system. This reaction in the hydrogen/oxygen system is supposed to take place via activated oxygen seeds as in the case of oxidation by hydrogen peroxide. 10 refs.

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

Achievement report on research and development in the Sunshine Project in fiscal 1977. Studies on hydrogen energy total systems and the safety assuring technologies thereon (Studies on preparing criteria for the safety assuring technologies for hydrogen energy total systems); 1977 nendo suiso energy total system to sono hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso energy total system no hoan gijutsu kijun no sakusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

Studies have been made on preparing criteria for the safety assuring technologies for hydrogen energy total systems. The outline of the technological guideline for hydrogen manufacturing processes in the high temperature and pressure water decomposition method is the same as that in the normal pressure water decomposition method. However, its high temperature and pressure environment can cause new safety problems. Considerations should be given on, for example, material problems in structural materials and insulation materials including electrodes and membranes, introduction of gas-liquid separation and pressure balancing devices, problems in electrolyte circulation, and safety problems that may occur because of generation of hydrogen and oxygen under high temperature and pressure conditions. This paper summarizes these matters by surveying literature data. In order to provide basic information to prepare criteria for safety assuring technologies for the gaseous hydrogen liquefaction process, surveys and studies were made based on different items of technological information and experimental study results. Safety assuring technologies were discussed on metal hydrides (promising means for storing hydrogen). Powder is used to enhance hydrogen absorbing performance, whereas the metal hydrides are pulverized as a result of repetition of absorption and discharge of hydrogen. This paper describes also metal dust explosion disaster and its risk of occurrence. (NEDO)

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on analysis of trends of technical innovation in Japan/Europe/the U.S.; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiso chosa (Nichibeio no gijutsu kakushin doko no bunseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For survey of the industrial competitive force, it is important to arrange the environment where the continuous and spontaneous technical innovation is generated. To recognize the present situation, the patent information relating to technical innovation, etc. were collected, indices of the number of patent, degree of the reference and scientific link in Japan, the U.S., and Europe were taken out by technology field to analyze the patent trend in the past 10 years. By technology field, the U.S. is superior in a lot of fields. Japan is at top rank in office supplies and camera fields, made strenuous efforts in automobile and semiconductor/electronic fields, but is behind others in medicine, biotechnology and aerospace fields. Concerning the number of patent registration in the U.S., Japan is superior to the U.S. in automobile/electric equipment/metal industries. Europe is superior in food and engineering fields. The U.S. is superior in aerospace industry and biotechnology fields. The U.S. is featured by a large number of patent applications by universities and government organizations. (NEDO)

FY 2001 report on the integrated evaluation of the research cooperation project. Research cooperation program on the development of environmental measurement use laser radar/research cooperation project on the mining waste water treatment technology using biology; 2001 nendo kenkyu kyoryoku jigyo sogo hyoka hokokusho. Kankyo kesokuyo reza reda no kaihatsu ni kansuru kenkyu kyoryoku - Baio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

By research groups having been sent, the integrated evaluation was made of the projects on the research cooperation with Indonesia in the development of environmental measurement use laser radar and the research cooperation with China in the mining waste water treatment technology using biology. As to the research cooperation with Indonesia, the purpose/target proposed were almost achieved, and all were favorably carried out. Especially, after finishing the project, the design/manufacture of an on-vehicle type Mie-scattering laser radar were made using the acquired laser technology. And, it was reported that an observation study of the state of air pollution in Bandung city was made using the laser radar. It can be said that generally the research cooperation with China was smoothly proceeded with. However, the Wushan mine is small in scale of management, and therefore, there might have been some points to be reviewed in selection of the mine for research. The pilot plant installed at the Wushan mine is not now operated. If the mine has strong management force, the effective use of the pilot plant after finishing the project might have been studied. (NEDO)

FY 2000 research cooperation project on the research cooperation for the commercialization of the regional adaptation type photovoltaic power generation system, etc. Research cooperation for the commercialization of the methane fermentation gas fuel cell power generation system; 2000 nendo kenkyu kyoryoku jigyo. Chiiki tekigogata taiyoko hatsuden system to no jitsuyoka ni kansuru kenkyu kyoryoku (Metan hakko gas nenryo denchi hatsuden system no jitsuyoka ni kansuru kenkyu kyoryoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research cooperation for the commercialization of methane fermentation gas fuel cell power generation system was made in a stock farm in Guangzhou city, China, and the FY 2000 results were summed up. In the project, the methane fermentation gas is recovered from animal faces, and a power generation system by fuel cell using the gas as fuel is constructed, and at the same time the waste is made compost and used as manure. In this fiscal year, the starting ceremony was made at the stock farm in Guangzhou city in June, and the main body of fuel cells was carried in and assembled. The trial operation of the system was successfully made in March 2001. At the same time, survey of the waste water from the farm and methane fermentation was made with accuracy. Survey was further made of the actual state of the recent energy supply/demand and the present situation of renewable energy as measures taken for non-electrification areas and environmental problems. As a result, the importance of further cooperation with the China side was emphasized in terms of the securing of animals/faces, optimum methane fermentation/recovery from animal faces, optimization of electric power of the area and environmental response, etc. (NEDO)

Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

Report on surveys and researches at the New Energy General Development Organization in fiscal 1980. Surveys and researches on hydrogen energy; 1980 nendo suiso energy ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-09-01

This paper describes surveys and researches on hydrogen energy in fiscal 1980. The high-temperature high-pressure water decomposition process in hydrogen manufacturing technologies had development proceeded on membranes and electrodes, and succeeded operating a 4 Nm{sup 3}/hr plant. Also for the solid electrolyte electrolytic process, a test plant of 1.3 m{sup 3}/hr was completed. The paper describes iodine and bromine system cycle, high-temperature gas atomic reactor cycle, and hybrid process with regard to the thermo-chemical method cycle. Problems in different cycles include necessities to advance the development paying attention on sufficient discussions on thermal efficiency of 35% or higher, heat regeneration and recovery, discussions on separation and transportation, and durability of reactive device materials. The paper also introduces research on hydrogen manufacturing utilizing chemical conversion of solar energy, biomass, and microorganisms. For technologies to store and transport hydrogen, the paper introduces metal hydrides, whereas Ti-based and misch metal-based alloys were found suitable. For transportation, Mg-based alloy hydrides were regarded as the most expected hydrogen absorbing material. Surveys were made also on the current status of the manufacturing industry, production and utilization of hydrogen. (NEDO)

Achievement report for fiscal 1976 on Sunshine Program. Research on safety technology in hydrogen energy system; 1976 nendo suiso energy system ni okeru hoan gijutsu ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

Material is collected relative to the safety of hydrogen inside Japan and outside and, on the basis of the collected data, generalization is made of a draft of general standards for the safety of hydrogen and a draft of technological standards for the safety of gaseous hydrogen and liquid hydrogen. In the draft of general standards for the safety of hydrogen, the physical properties of hydrogen and basic matters about the handling of hydrogen are put together, and the possible ignition sources are classified and measures against ignition are shown, and general matters about fire prevention and fighting are explained. Hydrogen attack and embrittlement are taken into consideration, and the caution to exercise when selecting, treating, and processing materials for use with hydrogen is described. Attention is paid to the handling of hydrogen, referring to the dangers of aerohypoxia, frostbite and cold death, and burns. Furthermore, a proposition is newly suggested this fiscal year, which emphasizes the need of disaster preventing facilities such as explosion-proofed electrical equipment and explosion-proofed wiring and explains where to install them and how to maintain them. Also taken up in the research are the need of measures, such as the delivery of safety education and training to workers, to cope with dangers peculiar to hydrogen, and the methods of implementing such programs. (NEDO)

FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

FY 1996 Report on the research and development project for interdisciplinary area. Part.2. Research on bionic designs; 1996 nendo yugo ryoiki kenkyu kaihatsu. 2. Bionic design ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The objects of this project are to elucidate the self-organization mechanisms of a living body, e.g., functional adaptation to environments and self-restoration, to utilize the molecular interactions in a living body, and thereby to establish the basic technologies for developing molecular motor functions, e.g., artificial organs. Described herein are the FY 1996 results. For creation of living soft tissues, N-ePTFE and Gf are found to be good base materials for cell growth in the serum-free culture, and may be applicable to bio-reactors. Sugar-bound high-molecular-weight compounds and artificial hyaloid body are created. For hard tissue materials, e.g., artificial articulation, the macrophage is activated by englobing worn debris of polyethylene, to activate the broken bone cells that absorb the bone, causing the artificial articulation to become loose. For researches on molecular motor mechanisms, it is considered that myosin changes the head morphology to give a driving force to the muscle, and this concept is studied in detail. The photosynthesizing protein is a molecule related to light and electricity, and is useful as the material to apply the living functions to industrial technologies. The technologies for assembling molecules are studied by utilizing the self-organization functions of living molecules. Development of other molecular machines is also attempted. (NEDO)