Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-08-01

Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

Survey of subjects on the geothermal technology development aiming at marked improvement of economical efficiency; Keizaisei no hiyakuteki kojo to mezashita chinetsu gijutsu kaihatsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing the geothermal development cost and increasing the amount of developable resource, the paper reviewed the geothermal developmental technology. Approximately 30 MW as a scale per unit is economical. The development cost is lowered by 2% if the period for development is shortened by two years, by 11% if the utilization rate is increased by 10%, and by 3% if the success rate is increased by 10%. The cost is reduced by 10% if the steam amount per 1 pit is increased to 1.5 times, and by 4% if the reduction amount is increased to 1.5 times. Improvement of survey/exploration/evaluation technology and improvement of power generation/management technology contribute largely to making the above possible. The drilling depth also corresponds with increases in the amount of steam obtained and the cost. The construction cost including the drilling cost is also an important factor, indicating a cost reduction of 15% if the unit price is reduced by 20%. If a 30% reduction of the power generation cost at a 30MW plant can be made, a 10 yen/kWh is realized, which shows that a geothermal power plant can be competitive with a thermal power plant. When thinking of it without subsidies, the geothermal power generation is most economical of all the renewable energy. In the light of the environment, the CO2 issue, etc., the geothermal power generation is much more advantageous than the thermal power generation. 7 refs., 28 figs., 8 tabs.

FY1998 report on the surveys and studies on developing next generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For further resource and energy conservation and environmental load reduction, development is necessary on innovative chemical reaction technologies. This paper describes surveys on next generation chemical processes. As non-halogen processes subject to development of new catalysts, new processes were investigated and searching experiments and discussions were given on isocyanate, propylene oxide, and phenol. Technological progress in the C1 chemistry was investigated. Problems in hydrocarbon compound oxidation, hydroxylation, and decomposition by utilizing microorganisms were put into order as application of environmentally friendly technologies. Marine biotechnical possibilities were surveyed. The surveys were given on new processes utilizing the phase transfer catalyst forming a third phase, manufacture of biodegradable plastics, and a novel reaction system combined with self-separation process using molecular assembly. Possibilities were searched on designing a truly simple production system of highly energy saving type. Such fundamental common technologies as structure analysis, property control and reaction engineering were investigated for methods to manufacture functional micro-powder chemical materials. Development was discussed on a system for technology assessment over whole product life cycle to structure a technology assessment basis. (NEDO)

Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

Exploration for petroleum and natural gas in Sonai Plain

Energy Technology Data Exchange (ETDEWEB)

Konishi, K

1965-09-01

Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

2000-03-24

Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

Fiscal 1998 R and D project on industrial technology. Development report on use technology of bioresources such as bioconsortia (Development of analysis technology of bioconsortia); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For use of advanced functions of bioconsortia (complex microorganisms composed of more than 2 microorganisms with certain specific function), this project analyzes specific functions of specific organisms and the interaction between the specific functions, and develops isolation and incubation technologies of component organisms. In fiscal 1998, to promote this project, the meetings were held frequently in National Institute of Bioscience and human Technology. Study was made on production of useful substances and useful degradation functions in association with bioconsortia. The result showed that microorganisms coexisting with nematode produced physiologically active substances exhibiting antimicrobial activities to tubercle bacillus, MRSA and others, microorganisms coexisting in eggs of some insects produced substances having antiviral activities and activities against pathogenic bacteria in a plant, and microorganisms growing in some plants or mycorrhiza organisms produced insecticidal substances or growing-promoting substance. The basic understanding was obtained on cooperative actions of bioconsortia to bioremediation and degradation of organic substances. (NEDO)

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

Technological development for super-high efficiency solar cells. Technological development of solar-high efficiency singlecrystalline silicon solar cells (high quality singlecrystalline silicon substrates); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (kohinshitsu tankessho silicon kiban no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development for high quality efficiency singlecrystalline silicon substrates in fiscal 1994. (1) On electromagnetic casting/once FZ bath method, a Si single crystal of 600mm long was successfully obtained by improvement of power source frequency and furnace parts. High carbon content resulted in no single crystal including solids. In undoped electromagnetic casting ingots, resistivities over 1500ohm-cm were obtained because of effective preventive measures from contaminants. (2) On electromagnetic melting CZ method, since vibration and temperature control of melt surface by magnetic shield was insufficient for stable pulling of single crystals, its practical use was hopeless. (3) On electron beam melting CZ method, a Si single crystal of 25mm in diameter was obtained by preventive measures from evaporation of Si and influence of deposits, and improved uniform deposition distribution in a furnace. The oscillation circuit constant of power source, and water-cooling copper crucible structure were also analyzed for the optimum design of electromagnetic melting furnaces. 3 figs., 1 tab.

Fiscal 2000 report of investigation. Part 2. Study on development of technology for reducing nitrous oxide; 2000 nendo asanka chisso teigen taisaku gijutsu kaihatsu ni kansuru chosa hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the study focused on the possibility of technological breakthroughs, from the results of the survey on industrial technological trend and the preliminary examination concerning the technology for reducing nitrous oxide (N{sub 2}O), proposals were made on the direction of the future R and D. As technologies for reducing N{sub 2}O generation in the furnace, there are improvement of combustion process and development of high performance fluidized mediums. These are definite in their targets and methods, and are applicable as urgent countermeasures for immediate effects as well as highly reliable in the process of implementation. Meantime, as technologies for reducing N{sub 2}O in a flue gas by catalysts, there are decomposition or reduction of N{sub 2}O in the middle-temperature range (300-400 degrees C) and in the low-temperature range (lower than about 150 degrees C), suppression of N{sub 2}O as by-product generated in the NOx treatment process, and development of catalysts. These are applicable for a broad range of N{sub 2}O sources including automobiles. In addition, requiring no great modifications in the equipment infrastructure, these technologies will seem to spread immediately to a broad range of fields once an effective catalyst is developed. (NEDO)

How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

Energy Technology Data Exchange (ETDEWEB)

Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

1999-07-05

They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-09-01

This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

FY 2000 study report on the study on technological development of the chemical processes of the next generation; 2000 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The technological development of the innovative chemical reaction processes is studied, in order to accomplish further energy saving, and reduction of resource consumption and environmental loads. Described herein are the FY 2000 study results. The program for systematization of the next-generation chemical processes systematically pigeonholes the undergoing projects and subjects to be studied, based on the principles of simplification, and sets the study fields of organic bulk chemicals, organic fine chemicals, highpolymer materials and inorganic materials. The program for investigation on next-generation chemical processes reviews creation and technological use of tailor-made biocatalysts, polymer materials which utilize wood resources, tailor-made reaction process engineering for handling fine particles in high-temperature reaction fields, production and processing of materials for high-performance polymer batteries, and extreme energy saving process for polyolefins, and proposes the revisions. The newly proposed study themes include novel C1 catalytic processes toward minimal wastes, and high utilization of biotechnology for novel processes to create materials. (NEDO)

Fiscal 1998 research report. Survey on R and D, and application technology of biotechnology; 1998 nendo chosa hokokusho. Bio technology no kenkyu kaihatsu, sangyoka gijutsu nado ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Survey was made mainly on use of biotechnology as resource saving and energy saving processes. Biotechnology is in wide use in a pharmaceutical field, while its application is on the increase in agriculture, food, chemistry, energy and environment fields. The USA is ahead of Japan and Europe. In the USA, there are more than 1000 ventures, and R and D of biotechnology, in particular, gene analysis and manipulation techniques are in progress together with acquisition of patents. In biomass energy, production of ethanol from corn, and development of biodiesel are in progress in the USA and Europe, respectively. Use of biomass should be promoted because of its global environment compatibility and sustainable productivity. In the future bio-market, genome analysis and its application are most important, however, Japan is behind in such technology in the world. The Joint approach by industry, university and government is necessary from the viewpoint of a future marketability and international competitiveness. Promotion of a public acceptance and nurture of creative talents are also important. (NEDO)

Survey on utilization of database for research and development of global environmental industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsu no tame no database nado no riyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

To optimize networks and database systems for promotion of the industry technology development contributing to the solution of the global environmental problem, studies are made on reusable information resource and its utilization methods. As reusable information resource, there are external database and network system for researchers` information exchange and for computer use. The external database includes commercial database and academic database. As commercial database, 6 agents and 13 service systems are selected. As academic database, there are NACSIS-IR and the database which is connected with INTERNET in the U.S. These are used in connection with the UNIX academic research network called INTERNET. For connection with INTERNET, a commercial UNIX network service called IIJ which starts service in April 1993 can be used. However, personal computer communication network is used for the time being. 6 figs., 4 tabs.

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell / low-cost and large-area module / next-generation thin-film solar cell (Manufacture of thin-film polycrystalline solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Fiscal 1997 is the first year of another 4-year-long research and development phase. In addition to researches for improving on thin-film polycrystalline Si cell efficiency that have been under way, new efforts are started, which include the development of practicality-conscious thin film producing technologies aiming at higher throughput and yield and the development of modularization process technologies which are necessary for putting thin-film cells to practical use. Concerning the formation of a power generation layer on a polycrystalline Si thin film formed by the ZMR (zone-melting recrystallization) process, studies are conducted for improvement on its throughput and yield using a new CVD (chemical vapor deposition) unit. A method of modularization is evaluated, which involves a laminate of a thin-film cell attached to a resin-coated, reinforced glass substrate and an EVA (ethylene vinyl acetate) back film. A remarkable achievement is earned toward the practicalization of technologies of thin film formation enhanced in quality and throughput and technologies of thin film modularization. (NEDO)

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of environmental adaptation of next-generation solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - jisedai taiyo denchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys are conducted of photovoltaic power system development projects and their utilization in Japan and overseas, and a discussion is made on the progress, technical challenges, effects, and implementation systems relating to the solar cell application technology development project under the New Sunshine Program. Compiled in the report are the results of surveys of the research and development of photovoltaic power systems and their diffusion in the U.S. and European nations, and the research and development strategies for and the trends of the development of various types of solar cells in these countries. The trends of research and development of non-conventional type solar cells are also collected, which include 3 cases of TPV (thermophotovoltaic) devices, 5 cases of new inorganic materials, 1 case of new organic materials, and 4 cases of dye-sensitized solar cells. In relation to the status of resources of crystalline compound-based solar cell materials, raw materials for solar cells other than silicon are taken up, and their reserves, manufacturing methods, quantities yielded and consumed, costs, etc., are surveyed. These are all taken into consideration in discussing the basic approach to the study of future research and development as it ought to be. (NEDO)

Fiscal 1998 research report. R and D on advanced combustion technology under microgravity environment; 1998 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research was made on explication of a combustion phenomenon by using a microgravity facility, and a combustor possible to realize advanced combustion technology. In the basic research composed of 5 themes by the international joint research with NASA, 52 drop experiments using JAMIC's facility and 100 drop experiments using NASA's 2.2s drop tower were carried out. The themes are composed of an interaction in droplet arrays combustion, combustion of binary fuel sprays, combustion characteristics of solid fuel, flame dynamics around a lean flammability limit, and mass transfer around a combustion field. In the experiment using the microgravity experiment facility and analysis evaluation of the experimental data, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit, formation mechanism of NO{sub x} and an advanced combustor. For applying a pre-evaporating/pre- mixing combustion system to a combustor for aircraft engines, studies were made on some issues such as improvement of a combustion stability, NO{sub x} discharge characteristics, and optimum fuel atomizing. (NEDO)

International research cooperation in fiscal 1997. Report on the research, development, and evaluation of environmentally-friendly combustion technologies; Kokusai kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the research and development of environmentally-friendly combustion technologies that had been conducted for six years beginning in 1992, analysis and discussion were made by a special committee dedicated to the evaluation of the efforts, and the outcome is stated. In the study of zeolite-base catalysts, a highly active catalyst was developed which assumes a multilayer structure of mordenite, etc., with titanium introduced thereinto using an NO-selective reducing catalyst. As for metal complex oxide-base catalysts, various catalysts high in activity were developed, based on saponite which is a laminar, clayey compound. As for alumina-base catalysts, details were learned of the reaction mechanism and catalysis activation sites and, helped by the findings, a silver-supporting alumina catalyst was produced. In the study of direct decomposition type NOx removing catalysts, a success was achieved in causing NO to be decomposed with high selectivity in an oxygen atmosphere by use of new-type electrodes, functional layers, and solid electrolytes. In the field of catalytic combustion, a PdO-Pt/Ba-Al2O3 catalyst was developed, which is to serve for a hybrid type catalytic combustion method. 19 refs., 112 figs., 25 tabs.

Fiscal 1998 research report. R and D on advanced combustion technology under microgravity environment; 1998 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research was made on explication of a combustion phenomenon by using a microgravity facility, and a combustor possible to realize advanced combustion technology. In the basic research composed of 5 themes by the international joint research with NASA, 52 drop experiments using JAMIC's facility and 100 drop experiments using NASA's 2.2s drop tower were carried out. The themes are composed of an interaction in droplet arrays combustion, combustion of binary fuel sprays, combustion characteristics of solid fuel, flame dynamics around a lean flammability limit, and mass transfer around a combustion field. In the experiment using the microgravity experiment facility and analysis evaluation of the experimental data, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit, formation mechanism of NO{sub x} and an advanced combustor. For applying a pre-evaporating/pre- mixing combustion system to a combustor for aircraft engines, studies were made on some issues such as improvement of a combustion stability, NO{sub x} discharge characteristics, and optimum fuel atomizing. (NEDO)

Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-10-15

Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-03-01

Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

FY 1999 survey report on the survey of the trend of the development of CO2 underground sequestration; 1999 nendo CO{sub 2} chichu kakuri gijutsu ni kansuru kaihatsu doko chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Paying attention to the CO2 sequestration technology, especially underground sequestration technology, this survey proposed a model case of the CO2 underground project including CO2 emission sources, means of transportation and CO2 injection equipment in terms of economical efficiency, environmental loads and technology in Japan and in other areas, and also studied projects on underground sequestration which are viable under CTI and other frameworks. The sequestration technology is classified into ocean sequestration, biological sequestration, underground sequestration and material sequestration. The underground sequestration is classified into the enhanced oil recovery, enhanced coal bed methane recovery, depleted oil/gas reservoir sequestration, and deep aquifer sequestration. The cost of sequestration is $100-300 per 1 ton of CO2, and is low in competitiveness at present. However, in the tertiary oil recovery and coal bed methane recovery, it costs nothing for CO2 reduction. As to the enhanced oil recovery, 66 projects were carried out in 1998 in the U.S. As to the enhanced coal bed methane recovery, projects in Canada, the U.S., and the U.K. As to the deep aquifer sequestration, one project in Norway. Concerning NEDO's project, there are great possibilities in aquifer and depleted oil/gas reservoir sequestration. (NEDO)

Survey and research for the enhancement of large-scale technology development 3. Patent researches on new tasks for development under large-scale project; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 3. Ogata project shinki kaihatsu tema ni kansuru tokkyo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Regarding 'high-speed computation systems for technological use' and 'manganese nodule mining systems,' researches are conducted into technological trends from the viewpoint of patent. As for applications for patents involving the Josephson effect device, there are 79 patents disclosed in Japan, with applications from Japan recording a peak in 1977-1978 and those from overseas in 1974-1975. As for important applicants, IBM distinguishes itself among those overseas while, in Japan, the Nippon Telegraph and Telephone Public Corporation occupies 47%, and Fujitsu, Ltd., 34%. In the case of GaAs-based transistors, businesses in Japan occupies as much as 90% of the applications overwhelming overseas businesses occupying less than 10%. As for the patents on manganese nodule mining systems, 183 Japanese patents are pending, with 88 already granted in America. While the main concern in Japan has transferred from the continuous elevator bucket system of 1971-1974 to the fluid dredge system, the fluid dredge system has consistently been occupying the overpowering majority in America. (NEDO)

Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1997-07-10

The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost large-area module manufacturing technology (Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu, Jisedai hakumaku taiyodenchi mojuru no seizo gijutsu kaihatsu (CIS taiyodenchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the production of a Cu(InGa)Se{sub 2}-based thin-film solar cell submodules, having a conversion efficiency of 13% and an area of 30 cm times 30 cm, at a cost of 140 yen/Wp (at a production rate of 100 MW/year). In the effort to fabricate a large-area photoabsorption layer, reproducibility was improved by the introduction of a technique for controlling the Cu/III group ratio in and the thickness of the metal precursor film by the use of ICP (inductively coupled plasma) analysis. A maximum conversion efficiency of 12.93% and a reproducibility of 85% were achieved, which meant that the production cost goal was achieved. In the effort to develop a high-resistance buffer layer fabrication technology, a fabrication method was developed in which a lower limit was specified for solution transparency enabling the completion of the film fabrication process with no colloid formation occurring in the solution. For preventing the high-resistance buffer layer fabrication process from growing too complicated, the steps were integrated into one for the MOCVD-ZnO:B window layer. As the result, the film fabrication process subject to the film fabrication control based on solution transparency was simplified for a great increase in reproducibility. (NEDO)

FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of environmentally-friendliness enhancement for next-generation solar cell development); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Shuhen yoso gijutsu ni kansuru kenkyu chosa, Jisedai taiyodenchi kaihatsu kankyo tekioka chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Though the trends of solar cell development are becoming increasingly diverse across the world, yet none has emerged to promise a stable solar cell supply in the future. Under the circumstances, studies were conducted to clarify strategies for solar cell technology development which would be well adapted to Japan's social environments, with the trends of development in the United States and European countries taken into consideration. The surveys covered the research and development and diffusion of photovoltaic power generation in the United States and European countries, and their solar cell research and development strategies and trends of development were put together. Surveys were also conducted into the research and development of unconventional types of solar cells, such as the dye-sensitized solar cell, organic solar cell, conjugate polymer solar cell, and the polymer/C{sub 60} based solar cell, and into the status of resources of materials for solar cells such as gallium, arsenic, cadmium, tellurium, indium, selenium, and germanium. Regarding the future of photovoltaic power generation research and development, it was concluded that commercialization technology development and basic research and development should continue. Also pointed out was the importance of the enlargement of the market for photovoltaic power generation systems. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Volume 1. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture low-cost large-area modules and survey and research on analyzing how to put products into practical use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu 1))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to assist research and development to put thin film solar cells for power use into practical use and a research to put thin film solar cell manufacturing technologies into practical use, survey and research have been performed on trends in the technologies inside and outside the country. Characteristic points in thin film solar cells during the current fiscal year include: expansion of production scale of amorphous silicon solar cells, rapid progress in poly-crystalline silicon thin film solar cell technologies, and enhancement of performance in large-area modules in the a-Si, CIGS, and CdTe systems. In the trends in research and development of amorphous systems, expectation is heightening on elucidation of optical deterioration phenomena, and establishment of suppression technologies thereof. Although the highest efficiency was not renewed in thin film solar cells of small areas, progress was seen in the post-stabilization efficiency in large-area modules. A thin film solar cell manufacturing plant having an annual production capacity of 20 MW was put into operation in October in Japan. Micro (poly) crystalline silicon based solar cells have high possibility of being compatible in cost reduction and performance improvement, and energetic researches are being carried out on them in recent years as the most promising candidate of the next generation solar cells. (NEDO)

Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

1994-07-25

With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

How large-scale technological development should be in the future. Survey and research on highly automated machines; Kongo no daikibo gijutsu kaihatsu no hoko ni tsuite. Kodo jidoka kikai ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

A survey is conducted about highly automated machines such as industrial robots. The task to be subjected to development as derived from a survey conducted about needs is the construction of a dangerous work robot. It is pointed out that work in coal mines, tall buildings, industrial complexes, or nuclear power plants may encounter large-scale accidents, and the task is how to perform such work in an automated way. The tasks concluded to be subjected to development after a seed survey analysis are categorized into three groups of element technologies, namely, sensors and recognition function, mechanism and materials, and control and data processing. These element technologies are to be ultimately integrated into a robot, for critical work which is a combination of a highly intelligent robot main body and an integrated management system. Since it will happen that humans have to directly operate such a robot under delicate conditions and share the burden of judgement and thinking, it is also necessary to develop technologies to solve problems of man-to-robot engineering. It is proposed that a dangerous work robot research and development program be established before development is started. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system (development of technology to manufacture thin film solar cells (surveys and researches on analyzing practical application )). Volume 1; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to identify and analyze quickly and accurately the technological trends inside and outside the country on thin film solar cells, to reflect the results effectively on research and development of practical application of the thin film solar cells for power use, and to aid the research on practical application of the technology to manufacture the thin film solar cells. This fiscal year introduced the new project of researching and developing the poly-crystal silicon-based thin film solar cells. Discussions were given on designing the solar cells, including setting of thickness of an active layer required to improve efficiency of the silicon-based thin film solar cells, the light confining technology, and surface passivation. Comparisons and discussions were given on the new amorphous/poly-crystal silicon thin film manufacturing method and the conventional plasma CVD process. A research development program was introduced for a super laboratory to aid establishing the practical application technology for the silicon-based thin film solar cells. Chalcopyrite compounds including CuInSe2, and CdTe have not shown deterioration even in a long-term outdoor exposure test, hence they are noted as materials for high-efficiency solar cells and studied actively. Although still small in area, the net conversion efficiency was found in the order of 17%. Technological development has started to search mass production processes and commercialization possibility in the future. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey and research on practical application - Volume 1); 1999 nendo taiyoko hatsauden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu - 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A 'Sub-committee for investigation of crystalline compound semiconductor solar cells' was established with the participation of experts from the industrial, bureaucratic, and academic circles to support the manufacture of ultrahigh-efficiency crystalline compound solar cells, and a survey was conducted about technical trends relating to III-V group compound solar cells. In the study of the trends and tasks of the state of the art technology, it is stated that the III-V group compound semiconductor multi-junction solar cell was steadily improving in efficiency, that the InGaP/GaAs 2-junction cell on a Ge substrate and InGaP/GaAs/Ge 3-junction cell in particular were moving toward mass production, and that the target for the 4-junction cell to achieve was 40% or higher in efficiency. For cost reduction, investigations were made into the heteroepitaxial technology, dimensional enlargement, mass production, raw material cost reduction, feasibility of the polycrystalline thin-film technology, light concentration, etc. For efficiency improvement, boundary layer control, structure designs, etc., were studied. Investigations were also conducted into nitride semiconductors, superlattice construction, etc., which related to new materials for thin films. TPV (thermophotovoltaic) power, etc., were reviewed for their practical application. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation); 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (furyoku hatsuden gijutsu ni kansuru kaihatsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey is designed to analyze, e.g., current status of large-scale wind power generation devices/system technologies and development trends worldwide, and to make predictions about future developments, in an effort to contribute to advancements in new technology for wind power generation systems in Japan. The international R and D cooperation programs promoted by IEA and EU have helped the participants produce a number of good results at lower costs. The European countries have developed the wind power generation industries in each area, promoted by the governmental subsidy policies, and are leading the world. The system is becoming larger, from around an average unit capacity of 250kW in the beginning of the 90's to 600kW now, reducing the cost by the scale merit. The improved computer capacity has made it possible to more easily analyze the complicated rotor aerodynamics, structural dynamics, wind characteristics and other factors related to wind power generation systems. The future R and D directions will include world standards for large-scale wind turbines, advancements in wind farm technologies, offshore wind power generation systems, advancement in design technologies, and new concepts for wind power turbine designs, e.g., floating wind turbine. (NEDO)

Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of novel amorphous solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project intends to improve on large-area amorphous silicon solar cell performance and to develop high-throughput manufacturing technologies for a reduction in the cost of modules. A film substrate type amorphous solar cell structure of the serial connection type named SCAF (series-connection through apertures formed on film) is contrived. Under this method, film formation using a stepping roll system newly developed for glass substrates may be applied, and the number of manhours required is allowed to be less than under conventional serial connection forming processes. The new technique is characterized in that serial connections are established via through-holes provided in plastic substrates. Making use of the technology, progress is attained in the development of high-throughput process technology for film substrate type amorphous solar cells and of efficiency enhancement technology. In fiscal 1997, an electron beam unit for plasma generation aiming at the elucidation of reaction processes in plasma was introduced, and technologies based on the equilibrium discharge technique were developed enabling high-speed a-Si film formation without degradation in film quality. The effect of trace boron addition to the tandem cell bottom I layer was investigated, and a stabilization rate of 8.05% was achieved using a 40cm times 80cm large SCAF cell. In fiscal 1998, endeavors were exerted for similar developments. (NEDO)

Report on 1978 results. R and D on coal gasification technology (R and D on manufacture of low calorie gas for electric power generation); 1978 nendo sekitan gas ka gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden'yo teikarori gas no seizo ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-05-01

The subject research has been conducted, since fiscal 1974, on the development of a pressurized fluidized-bed low calorie gasification furnace and on the various problems concerning a combined cycle power system, with the aim of establishing a technology for manufacturing fuel gas for power generation from coal and a power generation system linked with the technology. At the end of fiscal 1974, a test equipment was completed in Yubari for the development of gasification process with a coal processing capacity of 5 t/day, operating the gasification furnace for a total of 1,506 hours and gasifying Pacific coal for a total of 185 tons. The gasification reaction conditions were varied within the range of 0.3-1.5 mm coal grain size, 850-1,050 degrees C temperature, and normal to 8 atmospheric pressure, with a continuous test conducted for 48-96 hours, and with basic operation data obtained capable of producing gas having 1,200-1,400 kcal/Nm{sup 3} calories. In addition, through feasibility study, research and investigation were carried out for technologies relating to the practicability of a gasification power generation plant in 30 MW and 500 MW class. Implemented this year were studies for grasping various operating conditions by the 5 t/day gasification equipment, manufacture of a 40 t/day gasification equipment, and foundation work for construction in the Yubari test site. (NEDO)

Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development of reference materials for polymers; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kobunshi ni kansuru hyojun busshitsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As one of the efforts to establish national reference materials at an accelerated pace in a concentrated manner, a comprehensive survey was conducted on reference materials for polymers, and research and research was conducted for the development of such. In the comprehensive survey, investigations were made into the actual use of reference materials for polymers and their management at private-sector enterprises and public research institutes in Japan and at research bodies in the U.S. and Canada. In the development of reference materials for polymers, a procedure was contrived for synthesizing monodisperse oligostyrene specimens, polymerization was carried out using an improved synthetic method, and molecular weight distribution was analyzed. Using a homogeneous oligostyrene reference material for calibration, the mean molecular weight of an oligostyrene reference material was accurately evaluated by size-excluded chromatography. In the case of a specimen with its mean molecular weight not more than 1,000, the result exhibited excellent agreement with what supercritical fluid chromatography indicated. In the development of reference materials for characteristics evaluation, this in relation to methods for evaluating thermomechanical characteristics of plastics, efforts were made to develop reference materials for evaluating dynamic viscosity/elasticity of solid plastics. (NEDO)

FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

Comprehensive research concerning the development of effective utilizing techniques of biological resources (large scale research out of the framework). Seibutsu shigen no koritsuteki riyo gijutsu no kaihatsu ni kansuru sogo kenkyu (ogata betsuwaku kenkyu)

Energy Technology Data Exchange (ETDEWEB)

1991-10-25

This paper is a research report in which the cultivated production of forest resources, the development to useful substances and the systematization to take the root in a region were studied. The distribution maps of biological resources on respective woodland systems: that is, the nationwide distribution maps of the amount of resources in Japan as to the broadleaf trees in private forests and national forests, the available amount and kinds of tree were prepared. As for the establishment of cultivation technique of the super-short deforestation forest, that is, pursue of wooden growth to the maximum limit, the superior clone 26 system was selected from the willow group through the research of wooden cultivation and the clone which showed the maximum yield reached 24t/ha every year. As for the material preparation technique due to microbial enzymes, that is, the creation and breeding of fungi which have the high lignin decomposition power, a stock of fungi which has the high lignin decomposition power and the decomposition selectivity was created by the cell fusion and the UV (ultraviolet ray) radiation treatment. As for the use of effective components in wooden resources, many useful characteristics could be detected by applying the boiling, bursting and ozone treatment. As for the mushroom cultivation through the application of unused tree kinds, a new kind of mushroom for food service was selected to clarify the possibility of fruit body formation. The development of a new material from conifers is promising. 1 tab.

FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

Development of hydroponic system using agricultural waste. 2. Utilization of ozone for sterilization of nutrient solution; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 2. Ozone ni yoru baiyoeki sakkin ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Terazoe, H; Yoshihara, T; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1995-08-01

Discussions were given on a sterilizing effect of ozone on Fusarium bacteria in hydroponic culture, and its effect on components in the culture solution. In an experiment, dry air with O3 concentration of 3.5 ppm was sent into aqueous solution inoculated with Fusarium bacteria at a flow rate of 5 liters per minute. The Fusarium bacteria was sterilized nearly completely in about five minutes. No change was observed in pH, EC and dissolved oxygen concentration of the O3-treated culture solution. However, iron and manganese among the soluble components have been oxidized by O3 and precipitated, hence these components must be added after the O3 treatment. In spinach culture performed on a culture medium inoculated with Fusarium bacteria, ozone water containing dissolved O3 at 0.8 ppm was flown into a urethane foam medium and vegetable roots. This treatment has resulted in reduction of the number of strains occurred with a wilt symptom below that in the section flown with distilled water. The spinach has grown normally without showing an effect of the ozone water. 15 refs., 10 figs., 3 tabs.

Fiscal 1997 international cooperation project. Report on the results of the research on environmental harmony type combustion technology; 1997 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Out of the R and D on the environmental harmony type combustion technology, the results of the project carried out in fiscal 1997 were summed up. In the site survey, etc., visits were paid to France, Spain, Greek, Germany, the U.K. and the U.S. to have discussions and examine the trend of research on the NOx removal catalyst and catalyst combustion. In the actual R and D, the R and D were conducted on zeolite base NOx removal catalyst, oxide composite base NOx removal catalyst, alumina base NOx removal catalyst, direct decomposition type NOx removal catalyst, catalyst combustion, etc. In the R and D of the catalyst combustion, durability under high gas flow flux was examined of PdO-Pt/Ba-Al203 catalyst developed for low temperature use, which indicated that durability and low temperature activity were heightened. As high temperature use catalyst, high temperature durability was examined of the developed Pd0-La/Gd-ZrO2 catalyst, which showed that the durability was favorable. 322 refs., 261 figs., 55 tabs.

Achievement report for fiscal 1997 on investigative research on society compatibility of development of coal hydrogasification technology; 1997 nendo sekitan suiso tenka gas ka gijutsu kaihatsu shakai tekigosei ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In view of possibility of the future tightness in natural gas supply, establishment of coal gasification technology was set as the final objective, which can supply cheaply and stably the substitution natural gas of high quality by using coal existing affluently over the world as the raw material. An investigative research is carried out under a five-year plan on society compatibility required to assess the possibility of the practical application thereof. Fiscal 1997 has performed in continuation from the previous year the 'survey on process level elevation' and 'survey on the society compatibility'. This report summarizes the achievements thereon. In the investigative research on the process level elevation, the Shell's methane synthesis process based on an oxygen blown and dry feed coal gasifier was evaluated, and the calculation process was pursued on material balance in a hydrogasification reactor as having been performed in the 'survey on developing the coal hydrogasification technology' in which its reasonability was verified. In the survey on the society compatibility of the process, a survey was carried out on natural gas (including non-conventional methane hydrate and coal bed methane) and coals as raw materials for hydrogasification. (NEDO)

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research on practical application of set solar cell); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shisshiki taiyo denchi jitsuyoka kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Possibility of practical application of dye-sensitized solar cells (Graezel cells) is discussed. Fine titania particle preparation conditions and titania thin-film electrodes were optimized and an energy conversion efficiency of 7.7% was accomplished. The screen printing method was applied to the manufacture of dye-sensitized electrodes, and performance governing factors were grasped. The use of the screen printing method resulted in a conversion efficiency of 6-8.4% when the factors were optimized. Though lower than the 10% in the Graezel report, values near that were obtained. The status of latest research and development is compiled involving studies about electron transfer dynamics in dye-sensitized solar cells, manufacture of sensitizing dyes and mesoscopic metal oxide thin-film, electron transfer layers and their physical properties, and solidification of hole transfer layers. Research was conducted aiming at their practical application, and tasks and problems in each of the said items were point out. A logical approach to achieve high conversion efficiency was deliberated, and studies were made about how to propel forward endeavors involving design guidelines for high-performance sensitizing dyes, design and preparation guidelines for thin film for electrodes, analysis of stability, solidification of the redox electrolyte, etc. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted for the acquisition of a system evaluation technique for predicting the performance of standard photovoltaic power systems and evaluation technologies applicable to residential photovoltaic power systems different from each other in terms of tilt and direction, district, solar cell type, etc. In fiscal 1999, using data collected from the Hamamatsu field test facilities and residential photovoltaic power systems installed across Japan, various design parameters, such as the irregularity compensation coefficient, temperature compensation coefficient, and the incidence compensation coefficient were determined, and, using the parameters as the secondary estimation values, design parameters were updated. In the development of simulation technologies, basic studies were made about the shadow compensation coefficient, spectral response fluctuation compensation coefficient, and the composition of polyhedral arrays. Moreover, studies were made about the estimation of large area insolation, based on the horizontal surface insolation data collected at 21 sites of residential photovoltaic power systems in the Kanto district. (NEDO)

Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1997-03-01

The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

Development of magnesium semi-solid injection molding; Magnesium han`yoyu shashutsu seikei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakamoto, K; Sakate, N; Ishida, K; Yamamoto, Y; Nishimura, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Magnesium semi-solid injection molding is safety and clean process. We have investigated influence of molding conditions on mechanical properties and dimension accuracy of products by semi-solid injection molding. As a result it was proved that the accuracy of products by this process is superior to die casting. This advantage as well as better mechanical properties can be utilized for net shape molding of some automobile parts. 4 refs., 8 figs., 3 tabs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Separate Volume 1. Development of production technology of low cost/large area modules (Investigational study on the commercialization analysis); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu {sup H}akumaku taiyodenchi no seizo gijutsu kaihatsu{sup -} Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Jitsuyoka kaiseki ni kansuru chosa kenkyu) - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the study of commercialization of thin film solar cells for electric power use and the study of production technology of thin film solar cells, survey of the technical trend of the thin film solar cell was conducted, and the FY 2000 results were summed up. The typical Si system thin film solar cell is the amorphous Si solar cell, and the quantity production has already started in Japan and abroad. Further, with the aim of making use of characteristics of the amorphous Si solar cell and also making its defects up, the development of Si thin film solar cell using microcrystal Si and polycrystal Si is greatly expected. Among those, attention is paid to the hybrid type that was proposed for the remarkable improvement in the conversion efficiency of amorphous Si solar cell. In the compound thin film system, the Cu(InGa)Se{sub 2}(CiGS) solar cell was put on the market as product by SSI, though the market scale is small. Further, as to the CdTe thin film solar cell, trial manufacture of the large area module was made in view of the housing use. In addition, there was seen great progress in the color sensitized cell and organic semiconducting solar cell mainly in the U.S. and Europe. (NEDO)

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (low-cost Si substrates); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (usugata takessho kigan seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on manufacturing technologies for low-cost high-quality Si substrates in fiscal 1994. (1) On the 220mm square type electromagnetic casting technology, development of fast stable casting technology was studied using the previously installed 220mm square type electromagnetic casting furnace. As a result, continuous stable casting was achieved at high casting speed up to 3.0mm/min. Any degradation of crystalline quality due to high speed casting was not found. (2) On the 350mm square type electromagnetic casting furnace, oscillation circuit constants were analyzed for design of the power source for No.4 electromagnetic casting furnace. In graphite heating experiment using the 350mm square type water-cooling copper crucible heated by 1000kW high-frequency power source, sufficient heat quantity was obtained for initial melting of Si. Any problems in Si melting were not found through Al block melting test. 6 figs.

Fiscal 1997 report under consignment from NEDO on photon measuring/processing technology (development of power generation facility use high-function maintenance technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A research/development was conducted on technologies of photon applied measuring/photon applied processing/photon generation which are usable for heightening of reliability and maintenance efficiency of power generation facilities. In fiscal 1997, high melting-point metal particles were manufactured by high energy density laser for formation of high temperature and stabilized fine functional circuit. Further, a wavelength changeable ultra red laser light source was studied which can make in-situ measurement of gas concentration and components. A study was also made to examine the surface composition by measuring fluorescent X-rays emitted by radiating high intensity laser beam on the surface of material. A rod type and a slab type as a high-output complete-solidified laser are under development. There is also a development aiming at high speed/high quality photon processing such as high speed/high precision welding/cutting and laser joining. Besides, a study is being made of high energy pulse/high quality beam complete-solidified laser. The paper made a comprehensive survey of the trend of the photon measuring/monitoring technology, and made a systematical arrangement of the developmental subjects extracted. 142 refs., 357 figs., 62 tabs.

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of HFC-23 destruction technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. HFC-23 hakai gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-01

HFC-23 is produced as a by-product during HCFC-22 manufacturing (produced at by-production rate of about 2%, whereas the reaction control has limitation in reducing the production). This is one of the substances subjected to the greenhouse effect gas reduction in the climate change framework treaty. This paper describes the achievements in 1998 on developing the HFC-23 destruction technology. High-temperature pyrolysis decomposes the substance into HF and CO2, which are given absorption treatment by water and alkali to make them harmless, and are recovered finally as calcium fluoride. An equipment having the treatment capability of 195 kg/h was constructed. Design was made on a facility capable of treating fluorine containing waste water at 3 t/h at maximum. Utilities consumed in a factory (industrial water, acids for neutralization, and alkali) are used effectively to identify the effect of reducing the treatment cost. Discussions were given from the safety aspect on facilities to prevent leakage of fluorine containing waste water being a harmful substance. Fabrication was executed on a full-size treatment testing equipment that can utilize the utilities in the factory effectively, and trial equipment operation was performed to arrange the system prepared toward the future tests and researches. (NEDO)

Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

FY 2000 research cooperation project on plastic processing technology/quality inspection technology; 2000 nendo kenkyu kyoryoku jigyo. Plastic kako gijutsu hinshitsukensa gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of improving the production technology of plastic products in Saudi Arabia, the joint development was made of the formation technology/quality inspection technology of agricultural use and food packaging use polyolefin film optimum to environmental conditions of the site, in the light of the needs there, and the FY 2000 results were reported. In the field survey/joint study, for the xenon type weather resistant testing machine and the extruder of the inflation film forming machine which were transported from Japan, the following were carried out: confirmation of the situation of accepting them on the site, functional test of computer of the extruder, installation of the machine testing weather resistance, and the trial operation. In the domestic support study, the extrusion test at laboratory was conducted using the polyethylene resin produced on the site to acquire the basic data for formation stability. Further, the film formation test was made using the equipment with the same specifications as those of the equipment introduced to the site to study the performance of screw extrusion and the formation stability of film. Also conducted were the analytical test/quality evaluation of resin materials/film. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

Survey report of FY 1997 on the long-term energy technology strategy. Survey on the pre-assessment system of energy and environmental technology research and development; 1997 nendo chosa hokokusho (choki energy gijutsu senryaku chosa). Energy kankyo gijutsu kenkyu kaihatsu no jizen hyoka ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To select projects of the New Sunshine Program which is the locomotive for Japan`s research and development of energy and environmental technologies and to map out the Program`s long-term strategy, it is required to develop an effective methodology of assessing research and development themes. It is also necessary to establish the pre-assessment system which makes the assessment process more logical and which will enable the priority setting among different themes on the basis of objective and quantitative analysis. Additionally, transparency should be ensured for such a pre-assessment process through disclosure to the public and other means. The present survey aims to concretize the pre-assessment system by studying the system and techniques of an assessment system which is applicable to the research and development themes of the New Sunshine Program and is objective, quantitative and logical and which can ensure transparency and by receiving suggestions on the pre-assessment of Japan`s research and development of energies and environmental technologies through research on overseas trends of government-led research and development. 3 refs., 7 figs., 26 tabs.

FY 1995 result report. Research/development on the creation of high-grade combustion technology using a microgravity environment; 1995 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report summarized the results of the research survey carried out by Japan Space Utilization Promotion Center (JSUP) under the contract with NEDO's industrial technology research and development department. This research survey is aimed at creating high-grade combustion technology which can respond to the decrease in environmental pollutant in combustion exhaust gas from viewpoints of energy diversification and global environmental preservation in consideration of the stabilized energy supply. Established inside JSUP is a research/development committee on high-grade combustion technology which is organized by men of learning and experience from universities, national institutes, private companies, etc. Following FY 1994, the following were continuously conducted: (1) joint research with NASA as an international research cooperation; (2) test using microgravity test facilities and analysis/evaluation of the test data. The experiment was conducted using facilities, etc. of the underground gravity-free test center established as a part of the national research base arrangement project. A lot of experimental data were obtained and stored which are useful for elucidation of the combustion mechanism and the development of ground combustor. (NEDO)

FY 1996 result report. Research/development on the creation of high-grade combustion technology using a microgravity environment; 1996 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

With the aim of creating high-grade combustion technology which can respond to the decrease in environmental pollutant in combustion exhaust gas, the high-grade combustion technology research development committee was established inside JSUP (Japan Space Utilization Promotion Center), using the underground gravity-free test center. Following FY 1995, the following were conducted: (1) international joint research with NASA, and (2) tests using microgravity test facilities, etc. and analysis/evaluation of the test data. As to the international joint research, a lot of new information was obtained through the adjustment conference with NASA. Further, there were a lot of results obtained from joint tests and researches. Moreover, the leading experimental device and measuring device which are usable in the microgravity field were developed/prepared. Conducted were combustion/evaporation evaluation experiments on fuel droplet and groups of droplet, combustion characteristics elucidation evaluation experiments on high-density fuels, evaluation experiment on flammability limits, and elucidation evaluation experiments on emission mechanism of NOx, etc. Through those, abundant experimental data were able to be accumulated, and a lot of precious knowledge/information were obtained. Besides, the fabrication of high-class combustor test equipment for ground demonstration was started. (NEDO)

Report on research achievements in fiscal 1999 on development of simulation technology related to behavior of LSI circuit (re-commissioned portion); 1999 nendo LSI kairo no kyodo ni kansuru simulation gijutsu kaihatsu seika hokokusho (saiitakubun)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Development has been advanced on a new circuit design technology, in which the present digital circuit design performed according to the intensive circuit theory that regards reception and transmission of signals as migration of electrons is carried out by a new circuit theory centering on the intensive system (Quasi static closed circuit, QSCC) that regards reception and transmission of signals as propagation of wave motions. Studies required for structuring the QSCC theory were performed, such as verification of the reliability and effectiveness of the QSCC theory by means of the electro-magnetic field-circuit simulation and experiments and improvement of their completeness, development of the electro-magnetic field simulation technology required for the QSCC theory structuring, and development of a simple type design system based on the QSCC theory and a simple simulator for design verification. Specifically, the research and development on the eight items were carried out, including: 1) analysis of the generation and propagation mechanisms of electro-magnetic waves including those from LSI to circuit substrates, 2) analysis of electro-magnetic details of signals and power supply circuits including those from LSI to circuit substrates, 3) preparation of a library including the items from LSI to circuit substrates, and 4) development of a simulation technology including those from LSI to circuit substrates (QSCC designer). (NEDO)

Fiscal 1993-1998 integrated research report. R and D on advanced combustion technology under microgravity environment; 1993 - 1998 nendo sogo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For developing advanced combustion technology by using JAMIC's facility, the advanced combustion technology research committee supported by researchers of universities, national institutes and industries was prepared in JSUP, and R and D using a microgravity experiment facility and the international joint research with NASA were carried out. By using the advanced experimental equipment and measuring instrument developed for microgravity experiments, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit and NO{sub x} generation mechanism, and such precious results were obtained as storage of abundant experimental data, explication of a combustion mechanism, preparation of a database and find of new phenomena. In the ground verification experiment using the newly fabricated advanced combustor test equipment, various data effective for developing high-efficiency low-pollution combustors were obtained. Through the joint research with NASA including 5 themes, various results and the real relationship between the researchers were also obtained. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells/development of technology to manufacture low-cost large-area modules/development of technology to manufacture next generation thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction); 1997 nendo tiayoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module esizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A thin film single crystal silicon solar cell module is developed, in which a porous silicon layer is formed on the surface of a long-sized single crystal silicon substrate, a single crystal silicon film is integrated on the layer by epitaxially growing the film thereon to form a solar cell, and the solar cell is peeled off from the silicon substrate and transferred to a plastic film substrate. The achievements during this fiscal year may be summarized as follows: simultaneous formation of a porous silicon layer on a silicon substrate, reduction of anode formation current density from 200 mA/cm{sup 2} to 10 mA/cm{sup 2}, development of a silicon epitaxial device using a carbon heater, and attainment of aperture conversion efficiency of 11.8% in a thin film single crystal silicon solar cell. Three kinds of methods were developed to peel off the solar cell. A method was developed to grind silicon substrate surface from which the solar cell has been peeled off. A technology was developed to obtain a long-sized silicon substrate of about 30 cm times 10 cm times 0.1 cm from a 4-inch silicon ingot by using a wire saw. (NEDO)

FY 2000 report on the survey to support the R and D on the development of the coal/natural gas use CO2 recovery/utilization technology; 2000 nendo sekitan tennen gas katsuyogata nisanka tanso kaishu riyo gijutsu no kaihatsu ni kansuru kenkyu kaihatsu shien chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this study, technology to rationalize energy utilization is developed by which CO2 is efficiently converted into methanol which is the next generation liquid fuel by reacting CO2 with coal, natural gas and steam using solar heat. Together with this study, survey/study are conducted of the trend of the related element technology and the total system technology, trend of the competitive technology, study of comparison with the competitive technology, economical efficiency, possibility of the commercialization, etc. In this report, in Chapter 1, summarized are the trend of the R and D which each country conducts with the aim of using abundant solar energy in the Sun Belt and the trend of other R and D of energy utilization in each country. In Chapter 2, the paper describes the technology that Japan is now developing and the developmental trend of the related technology. In Chapter 3, the methanol supply/demand balance and the related researches were arranged. The most important points in future commercialization of the said technology are the establishment of technology and the economical efficiency. (NEDO)

Achievement report for fiscal 1998 on area consortium research and development business, 2nd year. Area consortium research and development (research and development of process-compatible flexible robot technology); 1998 nendo chiiki consortium kenkyu kaihatsu. Kotei tekiogata flexible robot gijutsu ni kansuru kenkyu kaihatsu (dai 2 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

To increase international competitiveness, the construction of highly productive systems capable of autonomously accommodating changes in manufacturing processes is indispensable. Robot technologies for flexible, robotized manufacturing lines will be established, and robotization will be promoted in industries related with transportation equipment and semiconductor in and near Kumamoto City. Optimization is to be achieved in such processes as IC chip insertion so that piston insertion into a cylinder with but an extremely little gap between them will be performed without scratches on the cylinder walls and that no plastic deformation will occur in the initial lack of positional correspondence. The technological tasks to be carried out include position detection based on visual information and skill making up, micro-force sensor of great precision and flexible force control, coordinated control of different types of robots, flexible handling mechanism, and integration of different techniques based on an information management system. The control of force now being exercised by humans will be reviewed from a new point of view and harmonization will be established between the human endeavor and sensing devices. Conceptual designs will be completed by the fiscal year end, with efforts concentrated on two prototypes, one for assembly lines and the other for IC inspection. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of high-reliability CdTe solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Koshinraisei CdTe taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for reliable CdTe solar cell modules, large in area and high in efficiency. In the study of large-area CdS thin film fabrication, a conversion efficiency of 12.5-14.2% was achieved in a cell in a large-area substrate using a mist method-aided process of continuous CdS film fabrication. In the study of large-area CdTe thin film fabrication, the optimization was studied of the base-forming CdS film fabrication conditions and of the CdTe film fabrication conditions in a method using a CdTe powder processed by dry kneading, and a conversion efficiency peak was found to exist when the CdS film thickness was in the range of 700-900 angstrom. In the fabrication of large-area submodules, a large-area substrate was taken up, and TCO (transparent conducting oxide) film was fabricated by the mist method, CdTe film by the normal pressure CSS method, electrodes by the screen printing method, and CdTe film patterns by the blast method. As the result, a conversion efficiency of 11.0% was achieved. In a cost estimation for large-area CdTe solar cell modules, 140 yen/Wp (conversion efficiency: 11.0%, annual production: 100 MW) was obtained. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of application type novel-structure thin-film solar cell manufacturing technology - Development of static micro-concentrator solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An acorn type concentrator is a 2-dimensional system and realizes relatively high magnification power, but it requires a special assembly process for modularization because the cells and the concentration system are quite small. Under the circumstances, studies are conducted on a prism array concentrator (PAC) which will demand a smaller burden for modularization. A PAC system is basically a 1-dimensional concentrator in terms of light collection performance. The cell to be attached to one plane in the longitudinal direction of the long triangular prism is so small as 5mm in width, yet it may be as long as 50-100mm, and the conventional flat plate assembly process may be made use of. A concentration efficiency of 82% and a conversion efficiency of 10.9% were obtained from a minimodule with a light intercepting area of 5cm times 4cm. Furthermore, a conversion efficiency of 19.7-21.4% was obtained when a small 5mm-wide cell applicable to a PAC type concentration was used. Since a prism type concentrator optical system will cost much for its molding and strengthening when it is built of glass, inexpensive EVA (ethylene-vinyl acetate copolymer) was utilized as an adhesive filler. (NEDO)

Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

Report on results concerning development of supermetal technology (FY1999-2000). Development of evaluation technology for formability of super metal (development of evaluation technology for formability of recrystallized microstructured plate); Super metal no gijutsu kaihatsu seika hokokusho (1999 - 2000 nendo). Super metal no seikeisei hyoka gijutsu nado no kaihatsu (bisai saikesshotsububan no seikeisei hyoka gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In connection with the innovative manufacturing of large base materials having a mesoscopic grain structure by means of technologies for high deformation accumulation control, recovery/recrystallization control, etc., research was conducted on evaluation technology for various characteristics such as formability, with fiscal 2000 results compiled. For the purpose of evaluating average grain size from an optical microscopic photograph of structures, it was judged reasonable to determine the average cut piece length. A device introduced to this development project was a horizontal goniometer capable of ODF (crystallite orientation distribution function)/pole figure measurement, qualitative analysis, and residual stress measurement. With warm rolling performed by controlling both material temperature of 7475 based alloys and roll temperature, thermally stable micro sub-grain structures were obtained. As a result of ODF analysis of this warm-rolled material, it was found that a {beta} orientation group existed very sharply in the area from the sheet surface to the center planar part of the thickness. The grain refinement of 5083 based alloys using a warm rolling method was also successful, with its ODF analysis revealing that the accumulation of the {beta} orientation group was very high as in the 7475 based warm-rolled materials. (NEDO)

FY 1998 industrial technology R and D project. Report on the results of the development of utilization technology of biological resource such bioconsortia system (Development of production technology of biological use petroleum substituting fuels); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Technology development was conducted for production of useful substances using the bioconsortia system. In FY 1998, the development of element technology was studied. As to the utilization technology of gut symbiotic microorganisms such as termite and longhorn beetle, clone types of gut microorganism complex system were analyzed to find out the diversification. In the decay of wood, co-culture of two species of mold fungus was increased in efficiency than single culture. More than 90% was classified/identified of the mold fungi accumulated (in wood piece)/separated for the utilization of plant symbiotic microorganisms. For the production of petroleum substituting useful resource, conditions were established of callus induction from immature embryos of tropical oil crops, especially oil palm, and of regeneration of a lot of small plants from the callus. To establish the Agrobacterium-mediated transformation system of oil palm, the binary vector harboring the reporter gene and selectable marker gene was constructed. Using the vector, oil palm tissues are inoculated and infected with agrobacteria. To heighten the function of palm oil, 10 particular clones were selected from the complementary DNA library obtained from oil palm fruit tissues. The genetic study of germs was also made. (NEDO)

FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

Fiscal 1997 technological survey report. R and D on micromachine technology (Development of high functional maintenance technology for power station equipment); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities were conducted in search of micromachine technology for a high functional maintenance system that inspects and repairs abnormal conditions such as cracks in a heat exchanger or a piping system without disassembling it in a power generating station such as a thermal or nuclear power plant. The activities were proceeded in four areas of (1) experimental manufacturing of the system (an inline self-running environment recognizing system, an external inspection system for fine tube group, and a system capable of light internal operation such as welding), (2) R and D on sophistication technology for functional devices, (3) R and D on common basic technologies, and (4) comprehensive investigation and research. In (1), examination of detailed basic specifications was carried out, as were examination of element technologies, experimental manufacturing and operation test of element devices, and performance evaluation. Further, a part of element devices was made on an experimental basis, with the basic functions demonstrated. In the comprehensive investigation and research, a trend in the future maintenance technology in power generating equipment was obtained and pigeonholed. (NEDO)

Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Survey and research of analysis of commercialization - Separate Volume: Survey of next-generation ultrahigh-efficiency solar cell system); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (Jitsuyoka kaiseki ni kansuru chosa kenkyu - Bessatsu : Jisedai chokokoritsu taiyodenchi system ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the preparation of a proposition concerning future research and development, surveys and studies were conducted centering about efficiency enhancement and cost reduction for the next generation ultrahigh-efficiency solar cell system. For improving the efficiency of the crystalline compound solar cell, studies were made about the prospects of the embodiment of a 3-junction and 4-junction types and of an increase in conversion efficiency expected to realize thanks to their light condensation behavior. It was inferred that anticipation of 29-47% conversion efficiency in 1 to 4-joint cells was theoretically acceptable. Four-joint structure cell fabrication would be a challenging task but would bring about an conversion efficiency of approximately 47% thanks to enhanced light condensation capability. As for cost reduction through the use of light condensation technology, surveys of overseas trends showed that the condensation-enhanced photovoltaic power system was characteristically fit for lower-price production. As for condensation and tracking systems, studies were made about cost calculation models of organizations involved in the United States and Europe, and then it was found that cost reduction in the optical system for condensation and in the tracking mechanism would be mandatory for the achievement of 75 yen/W. (NEDO)

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of CIS solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihtsu (CIS taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a technology to manufacture CIS-based thin film solar cells. This paper summarizes the achievements in fiscal 1999. In the research of a large-area light absorbing layer manufacturing technology, investigation was made on light absorbing layers in manufacturing sub-modules with a size of 30 cm times 30 cm. With regard to the temperature condition in the light absorbing layer forming process, it was found that the cooling rate affects particularly the adhesion in the connecting interface of the light absorbing layer and the Mo rear electrode layer. In addition, it was revealed that the sulfur take-in amount can be increases by extending the retention time at the sulfurizing temperature and by decreasing the temperature to turn the gas phase into selenium. In the research of elementary technologies to establish the mass production process, developments were performed on the high-resistance buffer layer manufacturing technology, the high-quality window layer film manufacturing technology, and the technology to manufacture rear electrode layer made of high-quality metals. In developing the patterning technology, two kinds of the existing patterning devices were modified and adjusted for patterning the substrates with a size of 30 cm times 30 cm. In addition, a processing device was installed in the conventional manually operated process for module finishing. (NEDO)

Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

Development of three-dimensional pipe bending technology; Pipe zai no sanjigen mage kako gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, K; Takeda, S [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

Recently, automotive parts uses move resin products or pipe-like products in order to achieve high quality or light weight. Additionally, the shape of automotive parts becomes more complicated. The rotary stretch bending method, although it is most popular method of bending a pipe, has some problems, such as a bending radius is limited due to use of bending mold, a thickness of an outer side of a bending portion is thinner, and a product is scratched easily during manufacturing. We have developed a three dimensional pipe bending process using a floating expanding plug and confirmed that this method can solve the above problems. 2 refs., 9 figs., 3 tabs.

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and development of technologies to manufacture amorphous silicon/thin film poly-crystalline silicon hybrid thin film solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon / usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental research has been performed on large-area low-cost manufacturing technologies on hybrid thin film solar cells of amorphous silicon and poly-crystalline silicon. This paper summarizes the achievements in fiscal 1999. The research has been performed on a texture construction formed naturally on silicon surface, and thin film poly-crystalline silicon cells with STAR structure having a rear side reflection layer to increase light absorption. The research achievements during the current fiscal year may be summarized as follows: the laser scribing technology for thin film poly-crystalline silicon was established, which is important for modularization, making fabrication of low-cost and large-area modules possible; a stabilization efficiency of 11.3% was achieved in a hybrid mini module comprising of ten-stage series integrated amorphous silicon and thin film poly-crystalline silicon; structures different hybrid modules were discussed, whereas an initial efficiency of 10.3% (38.78W) was achieved in a sub-module having a substrate size of 910 mm times 455 mm; and feasibility of forming large-area hybrid modules was demonstrated. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

FY1996 research cooperation for the development of the environmentally friendly technology for highly efficient mineral resources extraction and treatment; 1997 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The above-named project aims to jointly develop technologies to efficiently extract and recover valuable metals (gold, silver, copper, rare metals, etc.) from slag, with caution fully exercised to conserve the environment, for effectively utilizing non-ferrous resources in the Republic of Kazakhstan. The effort covers a seven-year period beginning in fiscal 1994. The elements which are studied are technologies that involve leaching, solvent extraction, electroextraction, recovery of gold and silver, and waste water treatment. In this fiscal year, wet treatment, gold and silver treatment, and waste water treatment are studied in on-site joint researches and in domestic researches for specimens sampled at the Kazakhstan site. In addition, based on the results of the above-said basic researches, some parts of the pilot plant to be constructed is designed and manufactured. For propelling forward the project, equipment necessary for joint research is procured and forwarded to the site, and Kazakhstan scientists are invited to Japan for training. (NEDO)

Fiscal 1995 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1995 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research and development were conducted jointly with Europe of an environmental harmony type high efficient catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. In the research and development of NOx removal catalyst such as zeolite base, reformation of mostly mordenite was done by ion exchange, ion implantation, skeleton element substitution, etc. A possibility was found out of applying the membrane formation method except ion implantation as reforming means. In the R and D of the complex oxide base NOx removal catalyst, it was found that the catalyst carrying copper and silver on silica and layer clay compound under optimum conditions shows peculiarly high activity, and there is little decrease in the activity, but rather increase in it even under vapor existence. An evaluation was made of NO resolution of direct resolution element carrying noble metal electrolyte on solid electrolyte, finding out that the highest NO selectivity is shown with Pd as electrolyte and at a baking temperature of about 1300degC. Development of high- and low-temperature catalysts was also made. 417 refs., 286 figs., 63 tabs.

Research and development achievement report for fiscal 1994 concerning the creation of advanced combustion technologies utilizing the microgravity environment; 1994 nendo bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The development committee concluded an agreement about on-site researches with NASA (National Aeronautics and Space Administration) for an international joint study, and the joint study was started at the underground microgravity center. Experiments were conducted at microgravity experimenting facilities and the data obtained were subjected to analysis and evaluation, which eventually contributed to the accumulation of useful data. In this fiscal year, microgravity experimenting facilities were utilized for experiments and tests for (1) the evaluation of the combustion and vaporization of fuel droplets and fuel droplet arrays, (2) analysis and evaluation of high-density fuel combustion characteristics, (3) evaluation of flammability limits, and (4) elucidation of the mechanism of the generation of NOx and the like. A total of 112 drop tests were conducted, and the acquired data were subjected to analysis and evaluation for the elucidation of the combustion mechanism, and findings were collected as mentioned below. Learned were the combustion behavior of fuel droplets such as ignition and flame propagation under item (1), combustion behavior such as ignition and combustion of high-density fuel under item (2), combustion behavior and combustion limits of premixed fuel under (3), and measurement of distribution of combustion products such as OH in the droplet fuel flaming zone under item (4). (NEDO)

Fiscal 1996 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1996 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research was conducted jointly with Europe of a catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. Reformation of mordenite and {beta}-zeolite was done by ion exchange, ion implantation, and membrane formation. A catalyst was searched for to obtain reducing agents, C5-C8 components, by decomposing light oil. Saponite, clay compound, showed by copper and silver ion exchanges approximately 50% of activity under 20,000h{sup -1}, C3H6 reducing agent, and without steam. The effect of the temperature of sintering on NOx selective reductionality of silver-carrying alumina catalyst was studied, and in sintering at 800degC, activity increased. When using conductive oxides like ruthenium oxide for electrolyte, NO decomposition selectivity increased. As to the functional layer carried above the Pd electrolyte, iron oxide and magnesium oxide increased NO decomposition selectivity. PdO and rare earth oxides forming compounds controlled variation of activity by dissociation/reoxidation of PdO. As to PdO/Gd203, the initial methane combustion activity was favorable, but there was seen deterioration with age. 271 refs., 281 figs., 58 tabs.

Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

Primary study on quantitative evaluation of driver fatigue; Unten hiro no teiryo hyoka gijutsu ni kansuru kiso kento

Energy Technology Data Exchange (ETDEWEB)

Noguchi, Y; Mochizuki, M; Toyofuku, K [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Katsuura, T [Chiba University, Chiba (Japan)

1997-10-01

Quantitative evaluation of physical and mental loads are effective in developing more human-friendly vehicles. Here attention has been focused on the mental load. Attempts were made to find some physiological indices that can be used for quantifying the mental load and resultant fatigue. Subjects were told to perform three different tasks in a climatoron, and the relation between physiological indices and their perception of fatigue as well as their capability of performing the tasks were analyzed. As a result, heart rate variability is a good index for quantitative evaluation of mental load and fatigue. 5 refs., 4 figs., 6 tabs.

Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology (Survey of peripheral element technologies - Survey of novel voltaic cell structure solar cell development); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu (shuhen yoso gijutsu ni kansuru chosa kenkyu - shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The present state and trend are surveyed of organic ferroelectric thin films, new carbon materials, fullerene compounds, and thermophotovoltaic (TPV) power. In the study of organic ferroelectric thin-film solar cells, the effort still remains at the basic stage, with the conversion rate as low as 3% in Europe and 2% in Japan. The progress of basic studies, however, is worth attention. It is deemed that 15% is the photoconversion rate to be currently expected from new carbon material solar cells. Fullerene compounds include some semiconductors whose bandgap values may be controlled across a 0.75-1.95eV range, and they may find their place in thin-film solar cells. However, their physical properties are not fully known, and their development into devices such as solar cells is scarcely reported. The research and development of TPV in the U.S. is led by NASA (National Aeronautics and Space Administration) and NREL (National Renewable Energy Laboratory), with their efforts concentrated on the development of portable power sources utilizing combustion heat. In Europe, TPV application to small-scale residential cogeneration systems is under study. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Feasibility study of wet-type solar cell commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu - Shissiki taiyo denchi jitsuyoka kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Dye-sensitized solar cell commercialization was studied for feasibility. Studies were made about photoelectric conversion efficiency and various factors supposedly to affect the life and other properties, and a wet-type (dye-sensitized type) solar cell was fabricated. In an endurance test, the dye-sensitized solar cell retained its initial performance after 3,500 hours of continuous irradiation. A 16 cm{sup 2}-large integrated type Graetzel cell was fabricated, and it achieved a photoelectric conversion efficiency of 4.6%. Furthermore, in the study of Graetzel cells, possibility of the creation of new electrolytic solutions was discussed, a non-TiO{sub 2} dye-sensitized solar cell was fabricated based on the self-assembled electrodeposition of the ZnO dye, and the feasibility was deliberated of a dye-sensitized solar sell using a composite oxide semiconductor. Concerning their development in the future, it was concluded that dye-sensitized solar cells including the Graetzel cell were equipped with the basic characteristics of a next-generation solar cell that would be requested to be low in cost and high in performance. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic power system commercialization technology (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Surveys and studies of peripheral key technologies/Surveys of ultrahigh-efficiency solar cell application fields); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu, Shuhen yoso gijutsu ni kansuru chosa kenkyu (Chokokoritsu taiyo denchi tou oyo bunya kaitaku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Surveys and studies were conducted in order to make propositions concerning the fields of application wherein the merits of ultrahigh-efficiency solar cells would be fully utilized. A questionnaire was held about solar cell application fields, and studies were made about new systems based on the need in the market for specific solar cell goods and capable of supporting their mass diffusion. Proposed as the result was the establishment of a rental (lease) system for photovoltaic power systems, a local photovoltaics advisory system, a market for used photovoltaic power systems, and so forth. In the feasibility study of photovoltaic power generation on unused land in agricultural villages, surveys were conducted concerning energy problems, the energy structure, the actual state of energy consumption, the abandoned farm and its utilization, and so forth. Propositions involving photovoltaic power feasibility were then made, which covered power consumption for greenhouse culture, energy supply for producing methanol out of biomass, power sources for insect incapacitating yellow fluorescent lamps, power sources for livestock barn air-conditioning, power sources for animal excretion treatment, and so forth. (NEDO)

Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture application type thin film solar cells with new structure (development of technologies to manufacture amorphous silicon and thin film poly-crystal silicon hybrid thin film solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was performed with an objective to manufacture amorphous silicon and thin film poly-crystal silicon hybrid solar cells with large area and at low cost, being a high-efficiency next generation solar cell. The research was performed based on a principle that low-cost substrates shall be used, that a manufacturing process capable of forming amorphous silicon films with large area shall be based on, and that silicon film with as thin as possible thickness shall be used. Fiscal 1997 has started research and development on making the cells hybrid with amorphous silicon cells. As a result of the research and development, such achievements have been attained as using texture structure on the rear layer in thin poly-crystal silicon film solar cells with a thickness of two microns, and having achieved conversion efficiency of 10.1% by optimizing the junction interface forming conditions. A photo-deterioration test was carried out on hybrid cells which combine the thin poly-crystal silicon film cells having STAR structure with the amorphous silicon cells. Stabilization efficiency of 11.5% was attained after light has been irradiated for 500 hours or longer. (NEDO)

1998 report on development of high-efficiency waste power generation technology. 2. Development of waste gasification and ash melting power generation technology; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Haikibutsu gas ka yoyu hatsuden gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In regard to waste gasification and ash melting power generation, a basic test and examination were conducted in fiscal 1998, with a full-scale development test made ready to start. In the development of technology for raising steam temperature, evaluation of high temperature corrosivity of SH materials and development of high-temperature dust removal system were carried out for example, as were development of dechlorination technology for thermal decomposition process and development of ceramic high-temperature air heater. In the development of technology to prevent exhaust gas reheating, preliminary examination was made on denitrification technologies using a catalyst with superior low-temperature activity. In the development of technology to reduce self-heat melting critical calorific value, investigation and basic test were carried out concerning a stable waste feed system, with a pilot test device experimentally manufactured and tested based on the findings. In the development of technology for reducing external fuel input, examination and analysis were performed on pretreatment techniques for waste plastics, with basic data obtained for a waste blowing system project. In addition, the thermal decomposition and combustion characteristics of waste plastics were clarified by the basic test. (NEDO)

Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Survey and research for the enhancement of large-scale technology development 1. Japan's large-scale technology development and the effects; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 1. Nippon no daikibo gijutsu kaihatsu to sono koka

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A survey is conducted into the effects of projects implemented under the large-scale industrial technology research and development system. In the development of 'ultraperformance computers,' each of the technologies is being widely utilized, and the data service system of Nippon Telegraph and Telephone Public Corporation and the large computer (HITAC8800) owe much for their success to the fruits of the development endeavor. In the development of the 'desulfurization technology,' the fruits are in use by Tokyo Electric Power Co., Inc., and Chubu Electric Power Co., Inc., incorporated into their desulfurization systems. Although there is no practical plant based on the 'great-depth remotely controlled submarine oil drilling rig,' yet oceanic technologies and control methods are being utilized in various fields. The 'seawater desalination and by-product utilization' technologies have enabled the establishment of technologies of the top level in the world thanks to the resultant manufacture of concrete evaporator and related technologies. Eleven plants have been completed utilizing the fruits of the development. In the field of 'electric vehicle,' there is no commercialization in progress due to problems in cost effectiveness though remarkable improvement has been achieved in terms of performance. Technologies about weight reduction, semiconductor devices, battery parts and components, etc., are being utilized in many fields. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (technical development for production of high purity silicon); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (taiyo denchiyo silicon seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of manufacturing technologies of Si for solar cells in fiscal 1994. (1) P in Si could be successfully reduced to 0.1ppmw by EB melting method. The condition possible to reduce P in Si while continuously supplying metal Si was found. The 20kg class EB melting equipment was also designed and manufactured which can be connected with solidifying rough refining process. (2) Use of a water-cooling copper mold was studied using a small melting equipment for cost reduction in solidifying rough refining process. As a result, the prospect of crucible-free technology for removal of P and solidifying rough refining was obtained. (3) B in Si could be successfully reduced to the target of 0.1ppmw by vapor addition method using a plasma melting equipment. (4) The prototype SOG-Si achieved a conversion efficiency of 14.1% as solar cell. In addition, the advanced solar cell prepared by efficiency enhancement process achieved a conversion efficiency of 15.9%. 3 figs.

1998 report on results of technological development of super metal. Innovative technological development for producing advanced structure controlled metallic material (high-speed large reduction rolling technology); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kodo soshiki kozo seigyo kinzoku zairyo sosei gijutsu kaihatsu (kosoku daiatsuka atsuen gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A report was made on the 1998 results concerning technological development of super metal. In the 'research and development of super metal', metallurgical examination has been made on crystal grain super refining process using a machining simulator, with studies carried out on crystal grain refining by utilizing large-strain deformation with more than 50% deformation for a single pass and a diploid structure. As a result, it was found that the crystal grain size can be refined to approximately 1{mu}m. Consequently, in fiscal 1998, a high-speed large reduction rolling test equipment was developed capable of rendering a sheathing technology in a mechanically testable size by a rolling method. This test equipment has such capacity as the maximum load of 1,000 ton and the maximum torque of 95 ton/m and is a rolling mill whose scale is largest in the nation on the laboratory level. The rolling speed can be 120mpm, a very fast speed for a large sized rolling mill. Moreover, equipped with an immediate water cooling facility adjacent to the rolls and an automatic operating system for example, it is a high function rolling mill capable of cooling and rolling that render the complex and delicate sheathing technology of super metal. (NEDO)

WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

FY 1995 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1995 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This promotion project on the cooperative research aims to efficiently extract and recover valuable metals (gold, silver, copper, rare metal, etc.) including in large quantity in tailings of ores in the Republic of Kazakhstan. In FY 1995, conducted were the field survey, support study in Japan, acceptance of researchers from Kazakhstan, conceptual design of pilot plant, etc. The ore/mineral for Cu is mainly an alteration ore of chalcopyrite. Au and Ag are low grade and unknown, and the main gangue mineral is pyrite. The low grade ore (waste/much) of the Nikolayevska mine has a tendency to leaching at normal temperature, but the ore of mostly chalcopyrite such as tailings from each place has difficulty in leaching. It gets leaching by increasing temperature. The more the temperature rises, the more conspicuous the reaction becomes. Further, chalcopyrite is leached with priority over pyrite. From the result, a technical potentiality was obtained of leaching of low grade chalcopyrite in tailings mostly of pyrite. The existence of Thiobacillus ferrooxidans was confirmed. As to the recovery method for Au and Ag, CIC is studied. The process of waste/much is solvent extraction, electrowinning study and leaching, and that of tailings is bacteria leaching and leaching study. (NEDO)

Research report on the effect of the large-scale industrial technology development system and on how it should be in the future; Ogata kogyo gijutsu kaihatsu seido no seika oyobi kongo no arikata ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

A survey was done about projects implemented under the above-named development system inaugurated in fiscal 1966, and studies are made as to how large projects should be in the future. The survey covered the subjects which had been completed by fiscal 1985, that is, the remotely controlled submarine drilling device for oil, seawater desalination and by-product utilization, electric vehicle, technology of comprehensive control of automobiles, pattern information processing system, direct iron making by use of high-temperature reduced gas, manufacture of olefines from heavy oil, aviation jet engine, resources recycling/reuse system, superhigh-performance laser-aided combined manufacturing system, submarine oil production system, and the optics-aided measurement/control system. Answers were heard from corporations concerned. The answers contained some complaints, concerning the shortage of experience on the part of participating corporations, degradation in planning functions, increase in the burden of leading companies, shortage of study or conference about an optimum promotion system, problems in accounting and auditing systems, etc., and suggestions were presented for improvement on large-scale projects. (NEDO)

FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This promotion project on the cooperative research aims at developing technology to efficiently extract and recover valuable metals including in large quantity in tailings of ores in the Republic of Kazakhstan in consideration of the environmental harmony. The support study in Japan was conducted as follows. As to the Nikolayevska low grade ore, high leaching speed and high leaching rate by grain refining were made possible. The coarse grain was also possible of leaching if leached for a long time. The sulfide froth is possible of leaching in fine grain and in the temperature range of 50 degrees C. The Zhezkent tailings were possible of leaching with sulfuric acid, by aeration, and in the range of medium temperature. The sulfide froth was possible of leaching in fine grain and at temperature of 50 degrees C. After filtration/washing and regrinding, high sampling rates of bulk concentrate and pyrite concentrate were obtained by sulfide flotation by zanthate. The Zhezkent copper concentrate was tested on various factors such as grain size, temperature, and washing/no washing, to confirm effects of bacteria. In the pre-observation test on Au and Ag leaching, cyanogen leaching test was conducted using Cu leaching residue. About Cu, studied were leaching (vat leaching, flotation froth machine agitation (temperature increase, bacteria)), solvent extraction, and electrowinning. About Au and Ag, studied were cyanogen leaching and process of adsorption of activated carbon. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the bioconsortium system utilization/production technology); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Fukugou seibutsukei riyo seisan gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the functional substance production technology, petroleum degrading/cleaning technology and high-grade utilization technology of the unused petroleum fraction, study was conducted of the culture control technology in substance production and substance decomposition by bioconsortia, and the FY 1999 results were reported. As to the functional material production technology, study was made of the separation/culture technology, functional substance production technology using bioconsortia (control substance searching method in the ocean microbial consortia system, isolation of control substance/structure determination/separation of production bacteria, elucidation of the inter-species communication substance function, heightening of function of the production microbial consortia), etc. Concerning the effective degrading/cleaning technology of petroleum compounds, study was made of the molecular genetic analysis technology, histochemical analysis technology, analysis technology of the solvent resistance mechanism, bioconsortia analysis system technology, global environmental purification technology such as the effective decomposition of environmental pollutants, etc. Relating to the high-grade utilization technology of the unused petroleum fraction, study was made of the chemical analysis of the photolysis crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

Achievement report in fiscal 2000 on technical development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of wooden board manufacturing technology using demolished building lumbers); 2000 nendo kenchiku glass nado recycle gijutsu kaihatsu seika hokokusho. Kenhciku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai wo mochiita mokushitsu board seizo gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development has been made on a wooden board manufacturing technology re-utilizing demolished building lumbers and waste plastics with an intention of saving resources and reducing wastes. This paper summarizes the achievements in fiscal 2000. In developing the technology to re-use demolished building lumbers, a method for removing metals attached to demolished building lumbers was established by using a magnetic separator and a metal detector, with which it was verified that iron can be removed nearly 100%. With regard to waste plastics, simultaneous use of specific gravity separation utilizing centrifugal force and electrostatic separation provided a prospect that metals and plastics of high melting points can be removed from mixed resins in waste household electric appliances, and that polypropylene (PP), polystyrene (PS), and ABS can be classified at high accuracy. In manufacturing waste wood and waste plastic boards, pilot plants were built to use the 'melt spray method', 'melt blow method', and 'laminating method' as the means to spray molten resin onto wood raw materials, wherein trials were performed on mixing molten resins with wood flakes, and on board forming. (NEDO)

Industrial science and technology research and development business for fiscal 1998. Research and development achievement report on glycoconjugate production and utilization technologies (Development of technologies of glycoconjugate-aided CO{sub 2} fixation and utilization); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu seika hokokusho (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Enzymatic and chemical methods were combined and methods were developed for synthesizing mucin type sugar chains and glycopeptides. The influence of sugar chain positions and structures on glycoconjugate stereo structures and physiological activities was analyzed, and glycopeptide structural activities and glycoconjugate remodelling were studied. To create an industrial advantage in a glycoprotein production system by use of zooblasts, sugar chain structure control through sugar transfase occurrence control was studied. For the production of man-adaptive sugar chains using yeast, new yeast variations were subjected to molecular breeding, and tested for the resultant improvement on productivity. Sugar chain marking and refining techniques and various responding mechanisms on the solid surface were elucidated, which enabled structure analyses using sugar chain recognition molecules such as lectins and antibodies. A database on interactions between sugar chains and sugar chain recognition molecules was constructed using the said findings. An analyzing program was also formulated tentatively. This paper also covers general surveys and studies on technologies of producing and utilizing glycoconjugates. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Dissolution/deposition method); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to manufacture the above at low cost by a dissolution/deposition method. Under this method, a film is fabricated containing crystals high in quality and large in size though the film area is very small. In fiscal 1998, an effort to fabricate a film to cover a 10cm square substrate failed. The failure is explained by that the heater was too small for the substrate area and that the failure to uniformly heat the substrate resulted in an inplane temperature distribution greater than expected. The furnace was modified in a minor way to narrow substrate temperature distribution as much as possible. Another attempt was made to fabricate a larger-area film on a 5cm square substrate, and then crystals grew to cover approximately the whole surface of the 5cm square substrate. Efforts will continue to achieve the goal. As for the mechanism of film fabrication on substrates of different kinds, self-coating is now described by difference in heat conductivity between a carbon substrate and silicon substrate. Thanks to individual control in a small film fabricating unit, a film thickness of approximately 100 micrometers was achieved. The distance of diffusion was 30 micrometers or more in the case of a small area, and the efficiency of a solar cell using this film was found at 10.2%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules (dissolution and deposition process); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (yokai sekishutsuho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was performed by noticing on the plasma spraying method as a process that can manufacture thin poly-crystalline silicon films at a high speed. Fiscal 1997 has established a technology that can form a silicon film directly without using seed crystals in an area of 2-cm square on a carbon supported substrate by using a small film manufacturing equipment using the dissolution and deposition process. The size of the crystal is as very large as several hundred {mu}m, by which a possibility of making high-performance solar cells was verified. Discussions were given to apply this technology to large-area substrates, whereas a device was developed, which is capable of forming a film in an area corresponding to 10-cm square. According to a film forming experiment using this device, the film has begun being formed on part of a 10-cm square substrate, verifying the effectiveness of this method. While the film thickness is about 100 {mu}m, it was confirmed that the crystal size will not change even if the thickness is made mechanically as thin as about 50 {mu}m. Further discussions were given on enhancement of wettability by means of coating, and light enclosing structure. (NEDO)

Development of production technology for deep-seated geothermal resources; Shinbu chinetsu shigen seisan gijutsu no kaihatsu gaiyo

Energy Technology Data Exchange (ETDEWEB)

Wada, T.; Akazawa, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1997-11-01

In order to increase the geothermal power generation volume in Japan furthermore after now, it is necessary to develop the deep-seated geothermal fluid collecting technique at 3,000 to 4,000m in depth and about 350degC. In order to collect the deep-seated geothermal resources economically and effectively, there are some principally important problems on production techniques such as P (pressure)-T(temperature)-S (flow rate)-D (fluid density) logging technique, P (pressure)-T (temperature)-C (chemical composition) monitoring technique, high temperature tracer monitoring technique, scale monitoring technique, scale protection and removal technique and so on. The PTSD logging technique is a measuring technique for collecting some data necessary to conduct production management effectively. The PTC monitoring technique is a technique for collecting data on the geothermal resources essential for the resources evaluation and presumption, and tracer monitoring technique is a technique for collecting actual measurement data of fluid flow analysis in the deep-seated geothermal resources. And the sale monitoring is a technique for collecting data on various kinds of scale components of the deep-seated geothermal water and in the steam. In this paper, these techniques are summarized. 8 figs.

Fiscal 1992 survey report. Coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. In the study of coal hydrogasification, a mathematical simulation was implemented to estimate the distribution of products with the pyrolytic reaction and the hydrogenolytic reaction controlled independently in the ARCH-2 (advanced rapid coal hydrogasification-2) process, the said two reactions representing the key concepts of the ARCH-2 process. It was then disclosed that a two-stage reaction control would increase the liquid yield. Also, a tentative calculation was made of gas cooling efficiency and cost performance in a process capable of achieving the target liquid acquisition rate. It was then found that BTX (benzene, toluene, xylene) production up to approximately 15% in terms of carbon was feasible and that the SNG price would be 29.03 yen/Nm{sup 3} with benzene priced at 90 yen/kg, these promising a better result than in the ARCH-1 process. The gas cooling efficiency of the ARCH-2 process was but 72.0% or less, however, which demanded improvement. Studies were made, based on the results of studies in progress since fiscal 1990, about what the hydrogasification process for Japan to develop should be. (NEDO)

Fiscal 1993 survey report. Coal hydrogasification technology development; 1993 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. The hydrogasification process that Japan should develop is a flexible process that operates on the three modes of the maximum SNG yield, the maximum heat efficiency, and the maximum BTX (benzene, toluene, xylene) yield. Such being the case, an ARCH (advanced rapid coal hydrogasification) process was proposed, provided with a reactor capable of an ARCH-1 type operation for the maximum gas cooling efficiency and an ARCH-2 type operation for the maximum liquid yield. As for the details of the ARCH process development, the time and priority for development were determined for each of the items in consideration of the technical contents and the steps of development in the flow from a bench plant to a demonstration plant. The technology of char cooling and extraction was specified as the first item to be immediately dealt with. As for the development of the hydrogasification reactor, it was concluded that it was suitable to begin with the development of an injector. According to the development plan, the cost required up to a pilot plant test was estimated at 2 billion yen. (NEDO)

Development of simulation technology on full auto air conditioning system; Auto eakon no simulation gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Fujita, N; Otsubo, Y; Matsumura, K; Sako, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Mazda has developed simulation technology on control of full auto air conditioning system. We have developed the development tool based on the technology, aiming at higher controllability of full auto air conditioning system and shorter development period. The tool performs simulation on control, on-vehicle evaluation of actual load operation, collecting data and analyzing them by personal computer. This paper reports our verification results on effectiveness of the technology/ and the tool. 4 refs., 9 figs.

Fiscal 1991 survey report. Coal hydrogasification technology development; 1991 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. Dealt with in the survey of basic studies on hydrogasification were the effect of gasification conditions, mechanism of tar decomposition, model-using estimation and assessment of reaction heat, and so forth. In an effort to develop a reactor, the current status was studied and future tasks were extracted concerning the one-through type and the internal circulation type entrained bed hydrogasification furnaces. In the study of practical application of the coal hydrogasification process, it was found that gas cooling efficiency would be increased from last fiscal year's 75.2% to approximately 78% by optimizing the process configuration. An ARCH (advanced rapid coal hydrogasification) process to have a novel reactor was proposed, and, for its commercialization, guidelines for dimensionally enlarging the process were worked out and tasks to discharge at each of the development stages were extracted. Relative to pilot tests, an efficient development program was deliberated, in particular, which comprised ARCH-1 and ARCH-2. (NEDO)

Fiscal 1994 survey report. Coal hydrogasification technology development; 1994 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. For the development of an ARCH (advanced rapid coal hydrogasification) process, a plan was prepared covering the basic concept of the process, overall development program, hydrogen/oxygen burner, and an injector. The overall development program comprises element studies (4 years) and the study of the operation of a 50 tons/day pilot plant (8 years), and deals with the development of a reactor and peripheral equipment. Next comes a total system verification effort using a 200 tons/day verification plant in combination with a hydrogen production process, and this aims to achieve commercialization at 3 million Nm{sup 3}/day. As for the hydrogen/oxygen burner, a structure was proposed after surveys of literature and patents on burner structures, ignition methods, and monitoring methods. In the development of an injector, a plan was prepared for testing, and improving, the performance in a cold/hot model of a specimen incorporating the proposed hydrogen/oxygen burner. Basic studies to be carried out include simulation-aided performance prediction. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of application type novel-structure thin-film solar cell manufacturing technology - Development of amorphous silicon/thin-film polycrystalline silicon hybrid thin-film solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu / amorphous silicon/usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to manufacture the above for the development of low-cost high-efficiency practical cells. Technologies were developed to homogeneously fabricate films with an average efficiency of 10% or more in a 100mm times 85mm area in a STAR (naturally surface texture and enhanced absorption with a back reflector) structure thin-film polycrystalline silicon (poly-Si) solar cell. The texture shape was improved for a higher light trapping effect and a STAR structure cell highly sensitive to long wavelengths and fit for use for a hybrid cell bottom layer was obtained. Various cells were examined for temperature characteristics, and it was found that thin-film poly-Si cells present a temperature coefficient equal to or less than that of bulk single-crystal silicon systems, and hybrid cells a temperature coefficient similar to that of a-Si systems. The technology was applied to a hybrid solar cell in which an a-Si cell was placed on STAR structure thin film poly-Si cells, and a resultant 3-layer a-Si/poly-Si/poly-Si cell exhibited a stabilization factor of 12.0% after 550 hours of optical irradiation. (NEDO)

Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-04-20

Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

Subjects on geochemical technology for geothermal power plant. Chinetsu hatsudensho ni okeru kagaku kanri gijutsu ni kansuru shomondai. 1

Energy Technology Data Exchange (ETDEWEB)

Hirowatari, K [Kyushu Electric Power Co. Ltd., Fukuoka (Japan)

1991-04-30

This paper introduces the following technologies and countermeasures found to be successful in solving geochemical problems relating to the maintenance and management of geothermal power plants belonging to Kyushu Electric Power Co., Ltd. In controlling condensate properties,curtailment of pH fluctuation range by changing the injection point of NaOH,inactivation of sulphur bacteria by using chloramphenicol and prevention of slime loading of the condenser strainer by running of the cooling tower without make-up water were achieved. In the environmental countermeasures,it was concluded that Fe-ion injection method was most effective to remove As out of waste hot waters which are all reinjected into the underground formation now. By understanding the characteristics of the well eruption fluids,the attenuation mechanism of steam producing wells could be estimated, which were interference,re-eruption and degradation of the reservoir temperature caused by the reinjected hot waters. And the problems associated with the attenuation of steam producing wells have been solved fundamentally by taking proper countermeasures to eliminate the influence of reinjected hot waters. The atteunuation of reinjection well was found to be caused dominantly by silica loading at the permeable zone of wellbore and to be effectively solved by high temperature reinjection of the waste hot waters, controlling of temp. degradation of hot waters to be reinjected and prevention of air mixing. After applying proper countermeasures, the attunuation rate of the reinjection well has been fairly improved. 13 refs., 21 figs., 2 tabs.

Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N; Omata, K [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

Survey and research for the enhancement of large-scale technology development 2. How large-scale technology development should be in the future; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 2. Kongo no ogata gijutsu kaihatsu no arikata

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A survey is conducted over the subject matter by holding interviews with people, employed with the entrusted businesses participating in the large-scale industrial technology development system, who are engaged in the development of industrial technologies, and with people of experience or academic background involved in the project enhancement effort. Needs of improvement are pointed out that the competition principle based for example on parallel development be introduced; that research-on-research be practiced for effective task institution; midway evaluation be substantiated since prior evaluation is difficult; efforts be made to organize new industries utilizing the fruits of large-scale industrial technology for the creation of markets, not to induce economic conflicts; that transfer of technologies be enhanced from the private sector to public sector. Studies are made about the review of research conducting systems; utilization of the power of private sector research and development efforts; enlightening about industrial proprietorship; and the diffusion of large-scale project systems. In this connection, problems are pointed out, requests are submitted, and remedial measures and suggestions are presented. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-30

The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

FY 2000 report on the results of the development of the next generation chemical process technology/development of the non-halogen chemical process technology; 2000 nendo jisedai kagaku process gijutsu kaihatsu non halogen kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of conserving energy and reducing environmental loads, the R and D were conducted of a new chemical process (non-halogen chemical process) using new catalytic reaction, etc., and the FY 2000 results were summed up. As to the development of a new method to synthesize isocyanate, the development was proceeded with of a method to synthesize diisocyanate by the dicarbamate reaction and pyrolysis of the carbamate, and the effect of catalyst on the yield of carbamate reaction was grasped. Concerning the development of a new synthetic method of epoxides, the development was proceeded with of the catalyst for synthesizing propylene oxides from propylene and hydrogen/oxygen, and conditions were obtained for preparation of a catalyst of the basic catalytic system and with reproducibility. Moreover, the development was proceeded with of a new catalyst used in doing epoxidation of 1-butene using the organic system hydroperoxide. Concerning the development of a new method to synthesize phenol, a promising system was found out by finding out the basic catalytic system of oxidation acetoxyl reaction and proceeding with the search for co-catalyst, carrier, etc. (NEDO)

FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a technology to measure inside of wells (Development of a fracturing technology); 1980 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper describes the achievements in fiscal 1980 in developing a technology to measure inside of geothermal wells, and of fracturing (to achieve enhancement and regeneration of well performance). Design and fabrication were completed on the in-tunnel sensor for a neutron/density logger. The sensor withstood use at a temperature as high as 275 degrees C. In logging and reservoir evaluation field tests, reliable data were derived even at a depth of 1,800 m and a temperature of 250 degrees C. Characteristics of response of radioactivity logging (neutron and density logging) to different igneous rocks were investigated by using rock blocks. For the fracturing facilities, improvements were given on transportation performance and installation workability of the preliminary observation device, by utilizing the experience obtained in the previous fiscal year. A composite (divided into two units) centrifugal multi-stage pumping device was developed so that a water injection test can be performed in a wide capacity range according to the intended wells, where nearly satisfying performance was derived. For the fracturing technology, in order for even small test pieces to be capable of evaluating fracture tenacity accurately with consideration on nonlinear behavior of rocks, elasto-plastic fracture tenacity tests were carried out with AE measurement being performed simultaneously. The paper also describes studies on fracturing fluids. (NEDO)

Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of solar system (research for solar/energy-conservation technology retrofitted to existing buildings); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa)

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for solar/energy-conversion technologies retrofitted to existing buildings. The estimated effects and economic viability of retrofitting technologies show that they bring very high energy-saving effects when applied to heating and hot water supply, which consume a large portion of energy, but relatively low energy-saving effects when applied to cooling, solar walls, glazed balconies and transparent insulators. The study on applicability of these technologies in Japan indicates that the technologies which can recover cost within an average life time are those applied to windows, solar collector systems for hot water supply and heating, and transparent insulators. Although these technologies are low in applicability to cooling viewed from the angle of cost recovery, retrofitted radiation type cooling systems improve not only cooling and energy-saving effects but also comfortableness.

Fiscal 1994 New Sunshine Program achievement report. Development of industrial solar system practicalization technology - Survey and research on solar system (Survey and research on city-oriented solar technology); 1994 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Solar technology and energy conservation technology (through retrofitting) which can be introduced into existing buildings are evaluated for their effect and economic efficiency. Studied are technologies verified to be technically feasible at the current stage, introducible into existing buildings without major modification, low in introduction cost, and high in energy conservation effect. How retrofitting technology should be in Japan is discussed. In Japan where demand for heat is smaller than in Europe or America and building service life is shorter, conditions to meet for efficient cost recovery are quite severe. Suitable measures to enhance cost recovery include use of multiple panels of low-radiation glass and light modulators for windows and use of collecting technologies such as solar systems for hot water supply and air solar collectors. Use of a transparent insulator is also recommended. Japanese houses demand repair and reconstruction very often, which helps cost recovery. Dependence on locality is extensive, and this causes difference in solar system application. Since it is high in temperature and humidity in summer in Japan, there is a great need for environmental comfort, and therefore not only energy conservation but also comfortable air-conditioning is important. (NEDO)

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. International cooperation project Collection of information on IEA wind power research and development program; 1999 nendo taiyoko hatsuden systsem jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo seika hokokusho. IEA furyoku kenkyu kaihatsu program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Participation was taken place in the executive committee for the implementation agreement of the IEA wind power research and development and other task workshops to investigate the status of research and development of wind power generation systems in other countries. The contents of the main activities under the implementation agreement of the IEA wind power research and development include researches on innovative technologies, analysis of the state-of-art wind power technologies, exchange of technological information, and expansion of the cooperation with industries, electric power operators, and non-IEA member countries. The agreement is participated currently by 17 countries and 19 contracted organizations from EC. The participants to the IEA R and D wind implementation agreement are taking activities in the tasks called the annexes. The activities of the annexes include exchange of fundamental technological information, annual generalization of the promotion of wind power energy utilization in the countries participated in the IEA implementation agreement, round-robin tests of windmills, and expansion of the wind characteristics database and the database for field rotor aerodynamics. Publications that have been issued include the 'Annual report', and newsletters issued once to twice annually. (NEDO)

Report on achievements in fiscal 1999 on the project for research and development of an intellectual base creating and utilizing technology. Research and development of standard substances related to polymers; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu jigyo gyomu seika hokokusho. Kobunshi ni kansuru hyojun busshitsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on researching and developing standard substances related to polymers. Investigations were performed on polystyrene with average molecular weights of 300 to 2,000 being the standard polymeric substance as the primary subject, and polycarbonate with molecular weight of about 300,000 as the secondary subject. Development was executed on the fundamental technologies related to chromatographic conditions for separation to acquire polymers without molecular weight distribution or with very little distribution (single dispersion), and sampling conditions for the sampling chromatography. Uniform polymers were used as the primary calibration standard substance to have developed the fundamental method and the fundamental conditions to value exactly the average molecular weight values such as in the single dispersion test. Polyvinyl chloride (PVC) was taken up as the valuing material as a polymeric material with less secular change being the indispensable element as the standard substance, and capable of being stably supplied. Round robin tests were performed by 16 testing organizations on the tensile elasticity specified in ISO10350 in accordance with the international standard guide 35 to have valued the standard substances. Variance in property values of PVC sheets was analyzed, and the standard deviation was verified. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. International cooperation project Collection of information on IEA wind power research and development program; 1999 nendo taiyoko hatsuden systsem jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo seika hokokusho. IEA furyoku kenkyu kaihatsu program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Participation was taken place in the executive committee for the implementation agreement of the IEA wind power research and development and other task workshops to investigate the status of research and development of wind power generation systems in other countries. The contents of the main activities under the implementation agreement of the IEA wind power research and development include researches on innovative technologies, analysis of the state-of-art wind power technologies, exchange of technological information, and expansion of the cooperation with industries, electric power operators, and non-IEA member countries. The agreement is participated currently by 17 countries and 19 contracted organizations from EC. The participants to the IEA R and D wind implementation agreement are taking activities in the tasks called the annexes. The activities of the annexes include exchange of fundamental technological information, annual generalization of the promotion of wind power energy utilization in the countries participated in the IEA implementation agreement, round-robin tests of windmills, and expansion of the wind characteristics database and the database for field rotor aerodynamics. Publications that have been issued include the 'Annual report', and newsletters issued once to twice annually. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction) (development of technology to manufacture micro light collection type solar cells); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (micro shukogata taiyo denchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

These technological developments are intended to demonstrate module efficiency of a micro light collection type solar cell of 15% by fiscal 2000, and obtain prospect on the module manufacturing cost of 140 yen per watt. Discussions given during fiscal 1997 are as follows: development has been performed on a design method to decide construction of a non-tracking micro light collection type module; in the state of cells being integrated on the module, the cells are arranged minutely and discretely, whereas, with discussions on a method to form them and assessment of the optical system as the main objective, single crystal silicon solar cells with a size smaller than 5 mm were fabricated on a trial basis; problems of forming micro cells by using the wafer cutting process were clarified; micro cells operating on light collection were fabricated trially to extract technological problems in light collecting operation and discuss technical problems in mass production; and development was performed on an evaluation method to analyze the cells' light collecting operation, and discussions were given on a method to estimate power generation amount from the light collection type modules. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

Report on results for fiscal 1997 on development of coal liquefaction technology . Development of liquefaction base technology (studies on development and internationalization of environmentally benign coal liquefaction technology); 1997 nendo sekitan ekika gijutsu seika hokokusho. Ekika kiban gijutsu no kaihatsu (kankyo chowagata sekitan ekika gijutsu no kaihatsu oyobi kokusaika kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The research objective is the development of environmentally benign coal liquefaction technology and the studies on internationalization of coal liquefaction technology. Implemented for the former are (1) research on improvement and rationalization of liquefaction process and (2) research on advancement of liquefaction base technology. In (1), studies were made on in-oil preprocessing technology and scale suppressing measures for the purpose of obtaining reform/high grade of coal, and on improvement of liquefied oil collecting ratio, sophistication of coal slurry and attainment of light oil/high grade from liquefied crude oil for the purpose of optimizing liquefaction reactive conditions and improving a solvent. In (2), in developing high activity/high dispersion type new catalysts, catalytic sufurization behavior and activity manifestation mechanism were explored, as were iron hydroxide based iron ore properties and liquefaction reactive characteristics. The initial reactive characteristics of liquefaction for example were investigated for the purpose of collecting basic data for expanding kinds of coal. In order to attain the latter objective of the research, a feasibility study of liquefaction location was conducted, as were the investigation including sampling of iron ore for catalytic material and the investigation of coal gasification technology. After the completion of the Australian brown coal liquefaction project, the development of the coal liquefaction technology commenced in fiscal 1994 produced a number of useful records and ended in 1997. (NEDO)

Study on evaluating method for earthquake resisting performance of steel piers; Kosei kyokyaku no taishinsei ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Isoe, A.; Hashimoto, Y.; Morimoto, C.; Sakoda, H.; Ishige, T.; Yoshikawa, T.; Kishida, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1998-12-20

After the shock of Hyogoken Nanbu Earthquake in 1995, protection against level 2 earthquake becomes important subject for civil structures. Subsequently plastic design methods for steel piers have been studied and rapidly introduced. The authors developed a method to evaluate the earthquake resisting performance of a steel pier with a single mass model. This model is useful for design because of its simplicity but on the other hand it can not consider the effects of piers` interaction in space. To include this effect in an analysis a simple 3 dimensional calculation model of box-column pier is developed. (author)

Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on long-term reliability of inverter); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - inverter no choki shinraisei no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In fiscal 1999, the power conditioner which is the primary component of a photovoltaic power system was subjected to an accelerated test, etc., for the evaluation of its durability. For the accelerated test, operating conditions were so set that acceleration be implemented according to Arrhenius' law at ambient temperature 40 degrees C and relative humidity 36%. For the operation of the power conditioner, it was so set that the operation duration be 3.5 hours with a rest time of 4.5 hours for the night or the like. In the accelerated test conducted as in the previous year, 1100 cycles were completed recording the maximum, equivalent to approximately 8-1/2 years according to Arrhenius' law. After the test, no life affecting changes were detected in specimen device A, B, or D. Specimen C, however, failed during the test. As for the evaluation of durability of components, the electrolytic capacitor in the power conditioner was named. Reliability related literature was investigated and a durability evaluation test was started, with consideration given to the voltage to apply and service temperature. (NEDO)

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on peripheral technologies around hydrogen); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

This report summarizes the fiscal 1975 research result on peripheral and seed technologies for hydrogen energy systems. Chapter 1 'Evaluation method for thermochemical techniques' reports critical study on qualitative evaluation method, estimation method for thermal efficiencies, and trial cost calculation example. Chapter 2 'Current state and problems of water electrolysis and hybrid technique composed of electrolysis and thermochemical technique' reports general survey on current water electrolysis and new technologies under development to clarify possible electrolytic voltage drop, from the practical viewpoint. Chapter 3 'Use of a high- temperature gas cooling reactor for hydrogen production' reports survey on the current and future reactors, and characteristics of such nuclear reactors, from the viewpoint that study on thermochemical technique is dependent on use of a high-temperature gas cooling reactor. Chapter 4 'Hydrogen transport and storage technology using organic compounds including oxygen' reports that acetone-isopropanol system is better for hydrogen storage. Chapter 5 'Water electrolysis using photo-semiconducting electrode' reports the additional survey. (NEDO)

Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-30

The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

Report on results concerning development of supermetal technology (FY2000). Development of technology for high-anticorrosive iron-based microstructured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of greatly improving strength and corrosion-resistance through ultra-refinement of crystal grains of steel materials, research was conducted on microstructure refinement technology utilizing strong magnetic fields and on mechanical property estimation technology for ultra-refined structure steel using computational science, with fiscal 2000 results compiled. In the research for grain refinement utilizing magnetic fields, an inline experiment of transformation was carried out and, as a result, equi-axed grains of 1.6 {mu}m were attained on a 3 mm thick steel plate of commercially used composition by a method of recrystallization after cold rolling. The experiment revealed that the 1 {mu}m grains could be obtained by setting cold-rolling work load to 80%. In addition, data were acquired relating to conditions such as steel composition affecting the formation of orientation in structures, work load and rolling temperature for areas to be recrystallized, holding temperature and time in the magnetic field, and intensity of the magnetic field. In the research for estimating mechanical properties of microstructures by computational science, a Monte Carlo simulation was carried out by employing the result of a polycrystal plasticity method program as the initial value, with a prototype established of the integrated simulation method from the deformation to the microstructure formation. (NEDO)

FY 1992 Report on the results of the research and development of micromachine technologies. R and D of highly functional maintenance technologies for power generating systems; 1992 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

Described herein are the FY 1992 results of the R and D project aimed at development of microcapsules, mother machines, examination modules without retrieval and working modules with retrieval, and their application to total systems for development of the highly functional maintenance technologies for power generating systems. Researches on the microgenerators involve studies and extraction of technical problems for structures, thin-film magnet production methods, coil winding methods, high-speed microbearings and microaccelerators. Researches on the mother machines involve development of the basic elements, on a trial basis, of the electrostatic actuators for the mechanisms of driving the main bodies, and evaluation of their characteristics by a minute torque analyzer. Researches on the examination modules without retrieval involve basic studies on, e.g., expansion driving, supersonic and microwave energy conversion devices for the expansion transfer mechanisms, development of these devices on a trial basis, evaluation of their functions, and extraction of the problems. Researches on the working modules with retrieval involve studies on shape memory alloy materials for tubular manipulators and actuator mechanisms. (NEDO)

Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

Report on achievements in research and development in fiscal 1982 commissioned from the Sunshine Project. Development of a pit condition measuring technology (Development of a fracturing technology); 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Development was made on a measuring instrument intended of acquiring information inside geothermal wells under high temperature and pressure. Research and development was performed on a fracturing technology to enhance characteristics of wells. What have been performed as a result of the development of the in-pit measuring instrument are application of high temperature logging cables as a result of development of logging devices, and the fabrication of a digital data analyzer. In developing the logging and reservoir evaluating technologies, field test were performed by using a logger that uses neutrons, installed with a radiation source. In developing the fracturing technology, discussions were given on the equation of relationship proposed from the standpoint of fracture dynamics, and investigations were made on examples of values, in order to anticipate hydraulic fracturing pressure applied in fracturing. In the research of fracturing additives, discussions were given on gelling agents supported by use of water glass, and alumina prop agents. For the preliminary observation devices, a high-pressure low flow rate control device was installed on the high-pressure plunger pump, improvement was made on the composite centrifugal multi-stage pump. (NEDO)

Fiscal 1998 research report on application technology of molecular assemblies for a functional protein system (Development of advanced maintenance technology for power plants); 1998 nendo kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu. Hatsuden shisetsuyo kokino mentenansu gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Basic research was made on engineering reappearance and industrial use of the complex function of molecular assemblies for a functional protein system of organisms. In research on a light controllable reaction system by physicochemical technique, construction of a light controllable bioreactor is in promotion. In research on a light controllable reaction system by biochemical technique, researches are in promotion on structure and correlation analysis of photosynthetic protein complex, stabilization of an activity, and conversion of light energy to membrane transport energy using cyanobacteria as material. In research on a molecular recognition controllable reaction system in a fine membrane region, correlation analysis of the structure and function of glutamine receptor channels is in promotion. In addition, researches were made on reconstitution of endocytic micromachinery, a multi-enzyme system for synthesis of glycosphingolipids, a complex redox system by genetic engineering technique, and application technology of molecular assemblies for a functional protein system. (NEDO)

The maximum allowable temperature of zircaloy-2 fuel cladding under dry storage conditions

International Nuclear Information System (INIS)

Mayuzumi, M.; Yoshiki, S.; Yasuda, T.; Nakatsuka, M.

1990-09-01

Japan plans to reprocess and reutilise the spent nuclear fuel from nuclear power generation. However, the temporary storage of spent fuel is assuming increasing importance as a means of ensuring flexibility in the nuclear fuel cycle. Our investigations of various methods of storage have shown that casks are the most suitable means of storing small quantities of spent fuel of around 500 t, and research and development are in progress to establish dry storage technology for such casks. The soundness of fuel cladding is being investigated. The most important factor in evaluating soundness in storage under inert gas as currently envisaged is creep deformation and rupture, and a number of investigations have been made of the creep behaviour of cladding. The present study was conducted on the basis of existing in-house results in collaboration with Nippon Kakunenryo Kaihatsu KK (Nippon Nuclear Fuel Department Co.), which has hot lab facilities. Tests were run on the creep deformation behaviour of irradiated cladding, and the maximum allowable temperature during dry storage was investigated. (author)

Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

Survey of pollution-resistant plants and their cultivating techniques; Osen busshitsu taisei shokubutsu to sono shokusai gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The reduction of forests due to environmental pollution has been surveyed, to investigate the pollution-resistant plants and solid microorganisms. In Japan, the blight of needle-leaf trees (pine and momi fir) and of Japanese oak has occurred, and blight of some other trees, such as wild cherry trees, Japanese apricot trees, birch, Japanese cedar, cypress and bamboo, has been reported from various regions. In this article, plants reported to be resistant to pollutants are listed, and the physiological features of these plants are described. Furthermore, to develop pollution-resistant plants, reports relating to clarification of the mechanism of resistance development and the genes involved are reviewed. Microorganisms which symbioses for roots support these root functions. They also suppress the activity of pathogenic microorganisms and improve the environment around the roots, thus helping plants to grow normally. The roles played by symbiotic microorganisms and how to utilize these organisms are discussed. Their functions in coping with acid rain and heavy metal pollution, and how to utilize such functions are also discussed. 707 refs., 13 figs., 13 tabs.

Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

Fiscal 1998 research report on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 1998 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Russia having natural gas resources largest in the world is actively promoting the basic research on liquefaction technology of natural gas such as Fischer-Tropsch (FT) synthetic catalyst, and its research potential is extremely high. This 3-year research project surveys the R and D trends of catalyst technology for liquefaction of natural gas, and fabricates the prototype FT synthetic catalyst based on the idea of Russian researchers to evaluate its feasibility experimentally. This report summarizes the following to clarify the research background: (1) The technology system for liquefaction of natural gas, and its future R and D trend, (2) The R and D trends of liquefaction technology of natural gas in the world, (3) The R and D trends of liquefaction technology of natural gas in Russia, (4) The research system of catalyses in Russia, (5) The activities of Russian catalysis research institutes, (6) The fuel liquefaction technologies of Russian major research institutes, and (7) The proposals from Russian research institutes. (NEDO)

FY 1999 research cooperation project. Research cooperation in development of technology to extract/treat mineral resources in environmental harmony and high-efficiently; 1999 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project is aimed at effectively using non-ferrous metal resource in Kazakhstan Republic and at conducting a joint development of the environment-friendly and efficient technology to extract/collect valuable metals (copper, gold, silver, rare metal, etc.) including in quantity in the slag generated with the mine operation in Kazakhstan. For the purpose of collecting valuable metals from slag, etc., the project is to develop the technology to collect valuable metals in saving energy and in low environmental loads by adopting the wet treatment process and to carry out the field survey on the existence of slag, etc. and the research on minerals. As the field research/domestic research, various element technologies are also to be carried out such as leaching, solvent extraction, electrolyte sampling, and waste water treatment. Based on the R and D of the element technology, a pilot plant is designed/fabricated and installed at the site in Kazakhstan. Then, the operation is studied and analyzed to make a technically/economically comprehensive evaluation. In this fiscal year, the field survey, research on the wet treatment, and test on the waste water treatment are conducted. Facilities of a pilot plant were transported to the site. (NEDO)

Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

Energy Technology Data Exchange (ETDEWEB)

Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

2000-03-01

Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

Research of fluidized bed cement clinker sintering system by pilot plant; Ryudosho cement shosei gijutsu no kaihatsu. 7

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Sato, N; Hashimoto, I; Nakatsuka, M [The Cement Association of Japan, Tokyo (Japan)

1996-09-01

While a cement manufacturing process generally performs sintering by using a rotary kiln, a development work has been carried out as a subsidy operation of the Agency of Natural Resources and Energy on a cement sintering technology using a fluidized bed consisted of two furnaces: a jet flow bed granulating furnace and a fluidized bed sintering furnace. This paper reports the results of tests and researches performed during fiscal 1995. A plant with a scale of 20 ton-a-day production started in 1993 after having gone through bench scale tests. The year 1995 conducted by August its performance evaluation, review of the operation method and the safety criteria, and generalization of the tests. A multi-stage cyclone system has been employed in the preheating equipment for cement material powder. A number of improvements have been realized in the aspects of construction and operation, such as stabilization of dust collecting efficiency by employing a high-efficiency type cyclone, and operation with reduced pressure variation. Based on these results, a construction had been progressed in parallel on a new plant upscaled to 200 ton-a-day production. The new plant was completed in December, 1995. 9 figs., 8 tabs.

Separation of unburned carbon from coal fly ash through froth flotation; Sekitanbai no shisshiki datsutanso gijutsu kaihatsu shiken

Energy Technology Data Exchange (ETDEWEB)

Miwa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Murakami, T [The Coal Mining Research Center, Japan, Tokyo (Japan)

1996-09-01

Coal ash tends to become containing more unburned carbon and porous substances depending on conditions of combustion, whose adverse effects to products due to water adsorbability, absorbability and color tones create obstacles in its utilization. Therefore, research and development works have been progressed on wet type carbon removing technology which is characterized in that coal is pulverized to preferable degrees and subjected to flotation. This paper reports the results obtained during fiscal 1995. The results may be summarized as follows: as a result of the comparison test on a column flotation machine and an FW type flotation machine of machine stirring type, the former machine showed better flotation efficiency; several methods were investigated on crushing as a treatment prior to flotation, whereas a mixer with greater circumferential speed and a homo mixer showed the highest efficiency; strength of the impact to the flotation efficiency was found to decrease in the order of pulp concentration > pretreatment time > collector addition ratio; and as a result of the evaluation on refined ash as a cement admixture and carbons as fuel, possibilities were found in them for practical application. 16 figs., 2 tabs.

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

Research, development, and evaluation of basic technologies for next-generation industries. Technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu hyoka. Saibo tairyo baiyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

The project aims to establish basic technologies for the mass culture of cells by utilizing the features of animal cells, which will enable a large, stable supply of fine chemicals such as highly functional physiologically active proteins whose industrial production the conventional technique of synthesis fails to realize. For this purpose, efforts are exerted to select cells which are capable of producing target substances, to breed highly productive strains, to develop a serumless medium that satisfies demands for an all-purpose feature and heat sterilization, and to develop technologies of high-density culture and effective refining, etc. Some DNA (deoxyribonucleic acid) recombination technologies are also resorted to. As the result, a high-density culture of 2 times 10{sup 8} cells/ml has become available. Production is now feasible of various differentiation-inducing elements such as monoclonal antibodies with anti-HB virus activity, DIF, etc. Furthermore, cooperation with the Tsukuba University leads to the discovery of a novel vasopressor peptide (endothelin). The heat sterilization accepting serumless medium, which is put to practical use as the first of the kind in the world under this research and development project, contributes to the advancement of basic studies about cell biology. (NEDO)

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the system evaluation technology; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu - System hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Based on the evaluation method for the performance prediction system of the standard photovoltaic power system, the R and D were conducted of the system generation output prediction technology which is general-purpose, simplified and applicable to various kinds of photovoltaic power system for residential use, and the FY 2000 results were summed up. In this fiscal year, the photovoltaic power system for residential use was increasingly installed at 15 places, and 100 sites in total were made database and analyzed. As to the development of simulation technology, technology of calculation was established such as the simulation of multi-plane array composition and correction of multi-plane array incidence. Further, technical information on system trouble and knowledge/information/proposal for reducing power generation loss were arranged by design parameter. Using the data on solar radiation/power loss at sites of residential use photovoltaic power systems installed in the Kanto area, value analysis of the capacity of wide area facilities of the photovoltaic power system was made by the statistical method. This study was compiled into the revised edition of design manual. (NEDO)

Fiscal 2000 survey report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of micrometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (micrometer order de seigyosareta material sosei process gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop sub-millimeter order coating creation technologies for engine cylinder bores, valve seats, and the like, for improvement on the performance of tribology related parts, which is necessary to assure environmental preservation, energy conservation, and resource conservation for industrial and transportation equipment. The coating liquid is applied in drops to the object and is irradiated with laser for re-melting for the formation of a coating. The technique is characterized in that it produces a 100 micrometer order coating. Activities are conducted in the four fields of (1) the technology of forming a coating by the use of high energy pulse laser, (2) technology of wear resistant surface treatment, (3) technologies for creating self-heating compounds and for bonding the same in practical applications, and (4) the analysis of the mechanism of tribological characteristics of a coating fabricated by hybrid laser surface treatment. In field (3), an Fe{sub 3}Al coating is fabricated by a combustion synthesis process in which a powder coating is pressed and simultaneously electrified for combustion (reaction), and the result is tested for physical properties. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of nanometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (nanometer order de seigyo sareta material sosei process gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop tribo-material creation process technologies capable of meeting the needs of environmental protection and energy conservation relative to automobile engine parts such as piston rings, cams, shims, and the like. Activities are conducted in the three fields of (1) the research and development of nanostructure material creation technologies, (2) research and development of tribological evaluation technologies, and (3) the verification of the developed technologies. In field (1), a nanostructure control process is studied, and tribo-composite materials are examined. In field (1), in fiscal 2000, the arc ion plating method is selected as a nanostructure control process, and the closed type nonequilibrium magnetron sputtering method as the base for development into a process. As for tribo-composite materials, Ti-Si-N based and Cr-Si-N based coatings find their feasibility in shims, and Cr-Si-N based and Cr-Si-C-N based coatings in piston rings. Compiled in this report are the summary, and the studies of nanostructure control process technologies, joint studies, composite ceramic coating practicalization technologies, and technologies for putting to practical use coatings which comprise layers of different substances. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. R and D of complex carbonhydrate production/utilization technology (Development of CO2 fixation/effective utilization technology by applying complex carbonhydrate); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toushitsu seisan riyo gijutsu no kenkyu kaihatsu (Fukugo toushitsu oyo nisankatanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of making an industrial use of complex carbonhydrate performing an important function in substance recognition, etc., which cannot be realized by only nucleic acid, protein and lipid, the R and D of the basic technology related to the production/utilization were conducted, and the FY 1999 results were reported. In the study of synthesis/utilization/remodeling technology of complex carbonhydrate using the chemical synthesis method, the R and D were made not only on the synthesis of sugar chain but for the synthesis method of the peptide added with sugar chain, that is, glycopeptide. Further, as to the reaction with the aim of the application, there was hope for large-quantity synthesis of milk oligosaccharide by the oxygen method. In the study of the design technology of complex carbonhydrate molecules, the systematical analysis using the model glycopeptide was conducted of effects of the sugar chain addition part and sugar chain structure on the 3D structure and physiological activity. Concerning the synthesis/utilization/remodeling technology of complex carbonhydrate using the biological method, study was made of the animal cell utilization, microorganism utilization, technology of structural analysis of complex carbonhydrate, etc. (NEDO)

Achievement report in fiscal 2000 on technological development to recycle waste building materials and glasses. Development of waste building material recycling technology (Research and development of recycling technology corresponding to grades of demolished building lumbers); 2000 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu (kenchiku kaitai mokuzai no hin'i ni taioshita recycle gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reduce wastes, and promote effective utilization of wood resources, research and development has been made on a demolished building material recycling technology. This paper summarizes the achievements in fiscal 2000. In developing the technology to manufacture high water resistant wood boards, discussions were given on resor type phenolic resin as an adhesive, and on the medium density fiberboard (MDF) being a substitute material for plywood as the wooden board. As a result, a highly water resistant MDF that can clear JIS E0 has been developed. In the research of a technology to enhance durability of wooden boards, the in-liquid roll press method was devised to perform impregnation of chemicals into board raw materials continually and simply, whose device was fabricated on a trial basis. With regard to recycling of medium to low grade wood-based wastes, researches were performed on pulverization of the wastes, fabrication of liquefied woods, and effective utilization of the liquefied woods. Both of a hammer mill and a chip saw crusher fabricated wood powder with nearly uniform grain size regardless of types of the wood-based wastes. Liquefaction of plywood and PB boards required more stringent reaction conditions than liquefaction of such ordinary members as pillar materials and laminated lumbers. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology - Photovoltaic system data book, separate volume); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu bessatsu (taiyoko hatsuden system data shu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the research and development of photovoltaic power generation system evaluation technology, great progress has been achieved in performance improvement and cost reduction as far as constituent devices such as power modules and inverters are concerned. In the designing of systems, however, quantitative elucidation of loss and power reduction factors remains insufficient. Under the circumstances, several types of photovoltaic power generation systems expected to be put to practical application in the future are taken up, test facilities are constructed which simulate them, and data are collected. The thus-collected data are utilized for research and development of evaluation techniques necessary for the improvement of photovoltaic system efficiency, such as design parameter quantification, databasing and utilization thereof, and simulation technologies, for the establishment of technologies for optimum designs and optimum operations. The data book accommodates data, arranged in an easy-to-use fashion, collected about verification test facility (interconnected systems, independent systems, and water pump systems) operation, weather conditions, and residential photovoltaic power generation systems. (NEDO)

Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

Report on the FY 1998 results of the New Sunshine Project (B version). Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In 1994, a memorandum on the research cooperation was agreed between NEDO and BPPT (The Agency for the Assessment and Application Technology) in Indonesia, based on the request for the coal liquefaction technology cooperation from BPPT. It includes the following items: conference for professionals to be held, invitation and training of Indonesian engineers, activity for joint field survey and potential survey of location of coal liquefaction commercial plant. Further in 1997, the secondary memorandum was concluded for the potential survey for securing the hydrogen required for coal liquefaction by coal gasification. The survey was summarized as the potential survey for location of coal liquefaction. In the testing study for improving economical efficiency of liquefaction process, it was made clear that the higher the Fe content of Banko coal is, the higher the reaction of liquefaction is, and that Fe compounds in coal show catalysis. In the Soroako area in Sulawesi island, there are the nickel mine run by PT. Inco. Soroako limonite is promising as catalyst material for commercial-scale coal liquefaction. In the gasification method, the plant construction cost increases, but the production amount of coal-derived liquid can be increased. That is more profitable than the production of hydrogen from natural gas. (NEDO)

`Technology for Advanced Treatment of High Melting Point Metal-Based Material,` local research and development of important technology for fiscal 1997. Development of materials creation technology for high efficiency power generator components; 1997 nendo juyo chiiki gijutsu kenkyu kaihatsu. `Koyuten kinzokukei buzai no kodo kako gijutsu` (kokoritsu hatsuden`yo buzai sosei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Efforts are made for the creation of high melting point metal-base materials to replace the currently-used Ni-base superalloys for the turbine to withstand higher operating temperatures. The main efforts made in fiscal 1997 are outlined. As in fiscal 1996, Nb-base solution alloys, in which solution reinforcement elements such as Mo and W are alloyed, are manufactured by button arc melting and tested for mechanical properties and texture/characteristics. In the designing and evaluation for a strongest Nb-base composite material, Nb-base composite materials are manufactured by use of particle dispersion-strengthening attained by addition of intermetallic compounds or elements to contribute to the formation of oxides, carbides, or nitrides. Nb-base composite materials may also be manufactured by use of eutectic-strengthening attained by utilizing crystallization in the process of coagulation. The resultant Nb-base composite materials are evaluated for their dynamic characteristics at high temperatures. In the development and evaluation of technologies for creating Nb-base materials for high-temperature components, larger specimens as heavy as several kg are tested in line with small specimens for basic studies, and the results are utilized for alloy designing for high-temperature materials. 50 refs., 97 figs., 15 tabs.

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Technological development of hot rock power generation system - development of elementary technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to identify the possibility of a hot rock power generation system, technological R and D has been performed on structuring of a man-made hydrothermal system, fracture mapping, downhole measurement and a circulating extraction system. This paper summarizes the achievements in fiscal 2000. With regard to the long-term circulating extraction test, a circulating heat extraction and test device was installed at the hot rock experimental field in the Hijiori area in Yamagata Prefecture, where geochemical data collection and tests including analyses thereon have begun. In reservoir bed analysis, a well module was incorporated into a reservoir bed simulator to improve the module so that comparison with the data of actual production on the ground can be performed. For the fracture mapping, AE having been observed during the long-term circulation test was analyzed, whereas it was estimated that the seismic source would not move or expanded during this period. A PTS logging has been performed during the long-term circulation test to investigate characteristics of the flow-out zone of the injection well and the production zone of the production well. In making the fracture model, an initial model was fabricated to estimate heat extraction behavior in the long-term circulation test. (NEDO)

Report on New Sunshine Program-supported undertakings for fiscal 1995. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported are the results of researches conducted in fiscal 1995. For the formulation of a general development design, data are collected about domestic high-temperature thermal wells through questionnaires and literature probing, and are scrutinized. As for the development of logging technology, a memory type PT (Pressure, Temperature) logger is experimentally constructed, and is found to properly operate in an environment of up to 350degC in a production well. An experimentally manufactured S-probe proves to be capable of heat insulation and sealing. In the field of PT monitoring, a high-temperature optical fiber is experimentally fabricated for study, capable of measuring temperatures up to 400degC. As for the development of high-temperature tracer monitoring technology, basic experiments are conducted about the thermal characteristics of aromatic acids, and preparatory experiments about gas phase tracers. In the study of scale monitoring technology, deep-seated fluids are collected and analyzed. In the field of production control, technical problems are discussed and information is gathered centering on methods for scale prevention and removal. 31 refs., 90 figs., 40 tabs.

Report on New Sunshine Program-supported undertakings for fiscal 1997. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu, shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Reported are the results of researches conducted in fiscal 1997. In the field of PTSD (Pressure, Temperature, Spinner flowmeter, fluid Density) well logging, the high-temperature performance of a memory type PT (Pressure, Temperature) well logger is confirmed in a demonstration test. As for the S-probe, modification is effected for the reduction of the outside diameter from 70mm to 56mm, and tests are conducted in real wells. As for the D-probe, a laboratory test is conducted and then the probe behaves as predicted. In the field of PCT (Pressure, Chemical, Temperature) monitoring, the sampler is subjected to an on-site test in Italy, when water is successfully sampled out of the well. In the field of scale monitoring technique, deep-seated fluid is collected and examined, and the scale deposition rate in the deep-seated fluid is determine. For the study of production control technology with respect to scale prevention and removal, an Mg-Si scale synthesis test is conducted in the temperature range of 100-300degC, and it is found that the solubility of scale decreases with a rise in temperature. 19 refs., 93 figs., 24 tabs.

Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

FY 2000 Development of technologies for reducing power consumption during the stand-by period. Report on the research and development results of rationally reducing power consumption by home electric appliances; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden seihin no taikiji shohi denryoku no goriteki sakugen ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The research and development project is implemented for development of the system which automatically switches off the power source for a standing-by appliance by analyzing life pattern in each home, in order to reduce consumed power during the stand-by period. The actual service conditions of appliances in each home are surveyed through the questionnaires and recording in the diary. The analysis results indicate that as high as 70% of those who are inquired take interest in energy saving, especially high among full-time housewives. The home electric appliances considered by many to wastefully consume power are functional-keeping types, e.g., (jar pots) and (toilet seats equipped with a washing function with warm water), and heating appliances, e.g., (hot carpets). The power consumption trends at each time in each home are measured and grasped by the aid of a tool with built-in personal computer, and the algorithm for predicting use of the appliances in each home is developed for each home, based on the analysis results. The prototype energy-saving adapter and centralized controller are developed, and subjected to various tests to develop the learning/controlling algorithms. The demonstration tests of the energy-saving adapter developed confirm that power consumption during the stand-by period can be reduced at least by 10%. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / R and D on process adaptive type flexible robot technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium bun`ya / kotei tekiogata flexible robot gijutsu ni kansuru kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of establishing robot technology required for the construction of a highly functional automation line with flexibility, the R and D were conducted. At Kumamoto University, a model following type power control system was studied into which polynominal trajectory formation algorithm was integrated. Also studied was damping control of robot arms in a disturbance environment. The following were further carried out: experimental verification (HIRATA Corporation) of the application of power control and intelligent control to transportation equipment production line, experimental verification (SAKURAI SEIGI Co. Ltd.) of the application of power control and intelligent control to semiconductor testing equipment, R and D (OMRON Corporation) of high accuracy force sensing and positioning system, research (Kumamoto Technopolis Foundation) on flexible arms/hands suitable for cooperative control, sensor-based skill (Electrotechnical Laboratory), research (Kyushu National Industrial Research Institute) on tactual system and tactual sensing, etc. 20 refs., 86 figs., 14 tabs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Development of production technology of application type new structure thin film solar cells (Development of production technology of high efficiency hybrid thin films/sheet solar cells); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Oyogata shinkozo hakumaku taiyodenchi no seizo gijutsu kaihatsu, (Kokoritsu hybrid gata hakumaku / sheet taiyodenchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of realizing low cost and high efficiency hybrid thin films/sheet solar cells, the R and D were carried out, and the FY 2000 results were reported. As to the formation technology of the upper cell, the following technologies were developed and the results contributory to the heightening of efficiency were obtained: technology for improvement of cell characteristics by gap widening of p layer, technology for optimization of formation conditions of i layer corresponding to the hybrid solar cell, technology for heightening of current by the intermediate ZnO layer just under the upper cell. Relating to the development of formation technology of high quality microcrystal thin films, it was indicated that the microcrystal silicon thin film had the conformity effective also for polycrystal silicon, and at the same time, the conversion efficiency of 12.8% and release voltage of 0.579V were obtained by the cell using the cast polycrystal board. In the thin film/polycrystal sheet hybrid solar cell in which all these technologies were integrated, the conversion efficiency of 12.0% was achieved, and the possibility was verified of achieving the target efficiency of 14% by further improvement of FF. (NEDO)

FY1995 study of feedback type gait training system; 1995 nendo feedback gata hoko kuren sochi ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose of this project is to develop and demonstrate the utility of feedback type gait training equipment designed for the measurement and evaluation by a walking training of the aged or patient. As similar concepts of walking training, a locomotion in the water for the aged is applied in rehabilitation. Our development of this study established the system of a suspending mechanism which revolves around the prop, and a walking on the circular type force plate by the aged or patient. It is possible to detect a walking reaction force of several patients from force plate simultaneously. And then, the data from force plate makes feedback signal to put up the patient like a buoyancy in the water. Concerning the evaluations of walking pattern a step range, a hanging ratio and a walking speed, etc. are acquired for each patient by the acknowledgment base. This system is actively able to perform a walking training continuously compared with conventional passive gait equipment. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Development of production technology of low-cost/large-area modules (Development of production technology of application type new structure thin film solar cells/Development of production technology of amorphous silicon-thin film polycrystal silicon hybrid thin film solar cells); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Oyogata shinkozo hakumaku taiyodenchi no seizo gijutsu kaihatsu, Amorufasusilicon hakumaku takessho silicon hybrid hakumaku taiyodenchi no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing the application type new structure thin film solar cell that is low-cost, high-efficient and practical, a developmental study was made of production technology of amorphous silicon/thin film polycrystal silicon hybrid thin film solar cells, and the FY 2000 results were reported. In the study of the heightening of efficiency of the small area hybrid cell, a structure was adopted in which a transparent intermediate layer was installed between a-Si cell and bottom poly-Si cell, and the initial efficiency of 14.0% was obtained in the small area cell 1cm square. As to the large area hybrid module, the initial efficiency of 11.7% and maximum output of 44.9W were achieved in the large area substrate module with a size of 910 x 455mm. In the indoor/outdoor evaluation of the output of hybrid modules, conducted were the outdoor measurement and the output measurement made every season under the mock spectral light in two-light simulator. In summer, F.F. was improved by spectral gain and anneal effect, and the effective output about 8% higher was recognized in the module after stabilization. (NEDO)

Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of complex biosystem analyzing technology; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The aim is to utilize the sophisticated functions of complex biosystems. In the research and development of technologies for effectively utilizing unexploited resources and substances such as seeweeds and algae, seaweeds are added to seawater to turn into a microbial suspension after the passage of two weeks, the suspension is next scattered on a carageenan culture medium, and then carageenan decomposing microbes are obtained. In the research and development of technologies for utilizing microbe/fauna-flora complex systems, technologies for exploring and analyzing microbes are studied. For this purpose, 48 kinds of sponges and 300 kinds of bacteria symbiotic with the sponges are sampled in Malaysia. Out of them, 15 exhibit enzyme inhibition and Artemia salina lethality activities. In the development of technologies for analyzing the functions of microbes engaged in the production of useful resources and substances for animals and plants, 150 kinds of micro-algae are subjected to screening using protease and chitinase inhibiting activities as the indexes, and it is found that an extract of Isochrysis galbana displays an intense inhibitory activity. The alga is cultured in quantities, the active component is isolated from 20g of dried alga, and its constitution is determined. (NEDO)

Research and development achievement report for fiscal 1998 on accelerated type biological function construction technologies. Development of new-type advanced-function enzyme creating technologies; 1998 nendo kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu seika hokokusho. Shingata kokino koso sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An artificial mutation/selection system was constructed in a laboratory based on molecular-level findings collected about the biological evolution mechanism, and biotechnology was studied for creating excellent biological functions. In the study of novel mutation generating technologies, selection is performed after the formation of numerous chimera enzymes by a family shuffling process using resistance to heat as the index. Then, a hybrid enzyme with its resistance to heat more than 10 times higher than that of the parent enzyme was obtained. In the study of establishing coordination between genotype and phenotype, a highly sensitive bacterial coordination technology was developed, and a highly sensitive detection method was constructed using a flow cytometer. As for technologies of highly efficient selection, a research was conducted about the selection of catalytic antibodies equipped with protease and esterase activity. In the study of technologies for enhancing adaptive walk in an evolution experimenting system, the usefulness is studied of a terrain survey based on the adaptive walk theory and a high-efficiency adaptive walk method using the mutation scrambling method. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system (Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Tandem type solar cells are developed, in which solar cells with different band gaps are stacked for effectively utilizing optical energy across the entire range of solar spectrum. A material gas supply control device for multiple epitaxial growth was added to a large-area GaAs film epitaxial growth unit, and a film thickness homogeneity of {+-}1% was achieved. A GaInP epitaxial layer fabricated in the same way was also enhanced in homogeneity. A low-carrier concentration layer was inserted into the top cell GaInP p-n junction for the construction of a p-i-n structure, and this improved on the short-circuit current. Furthermore, a p-p-i-n structure was constructed having two emitter layers, and this improved on spectral sensitivity for the achievement of a conversion efficiency of 13.6%. Studies were conducted about the tunnel junction which plays an important role in the stacking of cells, and the tunnel peak current was increased to 7.41A/cm{sup 2}. Fabrication is now under way of a GaInP/GaAs stacked cell, which is expected to exhibit a conversion efficiency of 25% or higher. In the case of a GaInAs cell to serve as the bottom cell, a conversion efficiency of 5.1% was achieved. Consequently, it is safely expected that a 3-junction stack of GaInP/GaAs//GaInAs will exhibit a conversion efficiency of 30% or higher. (NEDO)

Report on achievements in fiscal 1998. Development of a waste disposal and recycle related technology. (Development of a technology to dispose of air bags adequately); 1998 nendo haikibutsu shori recycle kanren gijutsu kaihatsu air bag tekisei shori gijutsu no kaihatsu nado seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

This technological development is intended to develop a process technology to dispose adequately of air bags convergently when they are removed from waste cars, with consideration paid on environmental and safety aspects. This technology that can dispose of air bags remaining as air bag modules (ABM) in large quantity and adequately can solve the problems of maloperation in opening them in cars and noise in conventional disposal methods. The recovery and disposal system using an inflator can be expected of reducing work load on dismantling contractors and enhancing the work safety. Furthermore, the energy saving process utilizing combustion of plastics can save resources. However, this technology has not elucidated how dioxins, dust, smoke, sulfides, and nitrogen oxides are generated and how the generation can be prevented. Therefore, an exhaust gas dioxin testing facility and an exhaust gas treating facility were installed additionally to the existing heating treatment facility to develop a disposal technology to treat adequately the exhaust gases generated when ABMs are disposed conveergently in large quantity, and treat the waste water discharged from the facilities. Fiscal 1998 has performed preliminary tests to accumulate fundamental data, and design and installation of the above two facilities. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1999 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant); 1999 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1999. In the disassembling study, wear, corrosion, and wall thickness change were investigated, and non-destructive inspection was performed on the major four facilities, and such newly developed devices as the liquefying catalyst manufacturing facilities, the slurry heat exchanger, and the let-down valves. The sampled test pieces were investigated of changes in the mechanical properties by means of the metallic structure inspection, hardness test, tensile test, and impact test. Deposits in the devices were investigated of their depositing conditions and constituents. The result reveals that the 3 Cr-1Mo-1/4V-Ti-B steel developed for the high-temperature, high-pressure, and hydrogen environment of the coal liquefaction plant showed excellent low-temperature tenacity and maintained good characteristics. No problems were discovered in corrosion resistance if PP using materials are used. The slurry handling centrifugal pump and instrumentation vales were worn out severely requiring replacements during the operation, for which further discussions are desired to be given. (NEDO)

Report on research achievements in fiscal 1999. Research and development of an ultra-high density electron SI technology (development of a technology for energy use rationalization); 1999 nendo chokomitsudo denshi SI gijutsu no kenkyu kaihatsu energy shiyo gorika gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

A high-density information network society is going to be realized in the 21st century. Information communication devices used therein are demanded of having high speed and high performance including acoustic and image digital processing, reduced size and weight, and low electric power consumption. While explosion in increase is estimated in the quantity of information handled by these information communication devices, there is a trend that the speed increase in CPU cannot follow the quantity increase. The present proposal is intended to make drastic performance enhancement by using the electron SI (comprehensive mounting) technology which includes making the LSI chips three dimensional and compounding light and electric power mounting, as well as design optimization. The present research and development has an objective to integrate the following three elements to achieve an ultra-high density electron SI technology: (1) a three-dimensional lamination technology making shortest wiring between LSI chips possible, (2) a light and electric power compounded mounting technology making high speed and large capacity transmission inside a board possible, and (3) optimal wiring structure design to suppress unnecessary electromagnetic radiation caused by increasing signal speeds. The research plan period lasts for five years. This paper reports the progresses in each theme in fiscal 1999. (NEDO)

Report on the achievements in fiscal 1999. Research and development on a basic technology to apply superconductivity (Research and development on a basic technology to apply superconductivity); 1999 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo oyo kiban gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The development of a basic technology to improve superconductivity characteristics has performed (1) studies on the high-temperature superconductivity mechanism, (2) studies on the critical current mechanism, and (3) search for materials. In Item (1), composition and temperature dependence were investigated by measuring superconductivity gap and change in the electron state of pseudo gap using photo-electron spectra and Raman scattering spectra. In Item (2), magnetic flux behavior in the vicinity of the irreversible line was investigated on magnetic flux dynamics of Bi2212 by measuring magnetic resistance and magnetization. High viscosity condition having strong magnetic flux liquid zone was discovered. In Item (3), Sr was used in place of Ba as the constituting element, and several new mercury-based superconductors were synthesized successfully by using the high pressure synthesizing method. In developing superconductive bulk materials and wire materials, elucidation was given on (1) an element technology for high magnetic power bulk materials, (2) an element technology for high critical temperature bulk materials, (3) a fundamental technology for manufacturing next generation wire materials, (4) a fundamental technology for manufacturing next generation large current conductors, and (5) growth mechanism in wire material crystals. Development of laminating and processing technologies for superconductive materials has worked on (1) a single crystal substrate technology, (2) a thin film lamination technology, (3) a standard bonding technology, (4) an advanced bonding technology, and (5) a thin film and bond evaluation technology. (NEDO)

FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

Summary of the achievements in fiscal 1991 in developing the coal liquefaction technology and the bituminous coal liquefaction technology. Studies by using a pilot plant; 1991 nendo sekitan ekika gijutsu kaihatsu rekiseitan ekika gijutsu no kaihatsu seika gaiyo. Pilot plant ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-08-01

This paper describes the achievements in 1991 on studies on the bituminous coal liquefaction technology using a pilot plant. Based on the detailed design of the 150-t/d pilot plant, study problems and analysis items were reviewed, and a material balance acquiring method and a reaction column data analyzing method were discussed. Utilization of the liquefaction simulator was attempted. Efficient execution of the pilot plant operation study requires to have the basic and support study achievements reflected on the pilot plant operation, and clarify the roles to be played by the groups. Therefore, discussion items were compiled. The overall process plan for the design and construction was reviewed based on the plan discussed in fiscal 1990. Fiscal 1991 has launched common civil engineering constructions. The operation plans for the main four facilities in the pilot plant, which have been prepared in fiscal 1988, were continued of reviewing to cope with the situation of the decreased construction budget. The budget was reviewed again in fiscal 1991, which would present a prospect of starting the operation in fiscal 1995. Annual reviews on the basic operation plans for the main four facilities and the conceptions taken to date were put into order. The project management system was also expanded and re-arranged, including the information registration and retrieval system. (NEDO)

Achievement report for fiscal 1998 on the development of super-metal technology. Development of technology of high corrosion-resistance iron base controlled microstructure materials; 1998 nendo super metal no gijutsu kaihatsu. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

During ultrafine structure formation due to transformation from austenite to ferrite in an intense magnetic field, the transformation is accelerated by the thermodynamic stabilization of the ferrite phase which is ferromagnetic. The application of an intense magnetic field works effectively during the generation of nuclei. When a magnetic field is applied during reverse transformation, a honeycomb 2-phase structure is formed oriented toward the direction of the magnetic field and, when the structure is vertically compressed, the recrystallized structure is made ultrafine effectively. In pearlite transformation, hardening occurs when carbon atoms supersaturated in density are introduced in the presence of a magnetic field gradient, and curing further promotes precipitation hardening. In a ferrite complex phase system, wherein ultrafine globular cementite is uniformly distributed, plastic instability becomes explicit in a tensile test. There is a good possibility that an ultrafine structure recrystallization model may be built by calculation, into which the distribution of energy stored prior to recrystallizing nucleus formation is incorporated. The profile of a conceptual process of off-line or in-line integration of heavy-strain process and intense magnetic field application has become tangible. (NEDO)

FY 1975 Report on results of Sunshine Project. Development of techniques of digging high-temperature beds (Feasibility study on digging high-temperature beds); 1975 nendo koon chiso kussaku gijutsu no kaihatsu seika hokokusho. Koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-31

The environmental conditions for which the digging techniques are to be developed have been set at 3,000 to 5,000 m as depth, 400 degrees C as temperature and 500 kg/cm{sup 2} as pressure. The environmental temperature was set at 250 degrees C as the first phase in the previous year. In this year, the temperature level is increased to 400 degrees C for the feasibility study on technological development. For development of the high-temperature bed digging apparatuses, masts, sub-structures, drawworks, slurry pumps, and pipe addition handling are studied as the problems involved in the rotary table method. Also studied are the related themes, e.g., drill pipes, drill collars, casing pipes, slurry, cementing and instruments to be installed in geothermal wells. For development of the bits, various problems to be solved are studied, including slurry circulation systems, bit diameter and speed of rotation, and bit configurations as those involved in the digging systems; heat-resistant materials, bit tooth forms, hardening of the edges, bearing configurations and cooling mechanisms as those involved in the bit structures; and optimum service conditions and selective use standards for roller cutter and solid bits. Other items studied include structures of the apparatuses for geothermal well mouth, and wear of digging tools for the air drilling method. (NEDO)

FY 1998 result report. Report on the results of the examinational research on the trend of technology development in the iron/steel industry; 1998 nendo seika hokokusho. Tekko sangyo no gijutsu kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The trend of the technology development in the Japanese iron/steel industry was compared with those in foreign countries and surveyed to increase the international competitive strength. From the viewpoints of technology, industry and goods, the iron/steel field was characterized based on the statistic data, and especially automobile use steel materials were selected such as cold rolling high tension steel sheet, surface treated steel sheet, and bearing sheet. The analysis of factors of competitive superiority was conducted, and the following were presented: measures for process continuation, and measures taken from the age of equipment and cost indexes. The paper also surveyed the trend of pig iron making/steel making technology in Asia. The present international technical competitiveness in the iron/steel industry in Japan, especially of automobile use steel sheet, is very high. This is because of the well-functioned demand-oriented development, and also as a result of the mutually influentially conducted equipment development such as process continuation and development of new goods, supposing the iron/steel continuous process and reduction in impurities. However, fears are the stagnation in the recent technical development strength and the saturation of new equipment. Moreover, the further heightening is needed of the international cost competitive strength of general-purpose products. (NEDO)

Report on survey for fiscal 1997. Survey concerning the effective use of the products of Industrial and Scientific Technologies Research and Development System; 1997 nendo chosa hokokusho. Sangyo kagaku gijutsu kenkyu kaihatsu seido no seika no katsuyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This survey aims at formulating measures for further soliciting the effective use of the products yielded up to date by the above-named system and at suggesting them to NEDO (New Energy and Industrial Technology Development Organization) who operate the system. In the survey, questionnaires are given and replied, about how the results of the industrial technology system and the public request for proposition system have been utilized, respectively. As for the enforcement of in-house research and development efforts after the project, 54% answer affirmative, 46% negative. The enforcement rate is relatively high in `recombinant DNA utilization technology,` `photoreactive materials,` `bio-element,` and `super-advanced processing system.` The enforcement rate is low in `fine ceramics` and `technology for creating space at great depth.` As for the feasibility of the products of the system, 76% are judged feasible and 23% unfeasible. Ranked high in feasibility are `processing technology creating advanced functions,` `fine ceramics,` `ultimate work robot,` and `super-advanced processing system.` Feasibility is judged low in `recombinant DNA utilization technology,` `photoreactive materials,` and `bio-element.` 2 refs., 16 figs., 6 tabs.

Research cooperation project in fiscal 2000. Research cooperation on developing high-efficiency mineral resource extracting and processing technology of environment harmonizing type; 2000 nendo kenkyu kyoryoku jigyo. Kankyo chowagata kokoritsu kobutsushigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A joint research has been carried out in the Republic of Kazakhstan on a technology to extract and recover efficiently the valuable metals (copper, gold, silver and others) contained in ore wastes in large quantity, with considerations given to the environment. This paper summarizes the achievements in fiscal 2000 being the last fiscal year. This joint research has performed researches on the processing technology and processes, and on the operation research by using a pilot plant, using low-grade ores in the Nikolayevska Mine and ore wastes from the Zhezkent Mineral Dressing Mill as the objects. As a result of the researches, the following matters were discovered: if the ore wastes are used as the starting materials in the copper recovering process using the chemical leaching process, the copper price of $1,800 per ton is the breakeven point; economic effect is enhanced by grinding the starting materials into finer particles, adding a zinc recovery process, and recovering gold by using cyanogens; and this pilot plant is pollution free, and easy in maintenance and control. These processes were concluded effective in reducing the efficient waste ore processing and environmental cost being the environmental problem in Kazakhstan. (NEDO)

Report on the surveys in fiscal 1984. Surveys on the possibility of using coal liquefied oil as a raw material, and technological development thereon; 1984 nendo sekitan ekikayu no genryoka no kanosei oyobi sono gijutsu kaihatsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

With an objective to establish an optimal method for utilizing coal liquefied oil, surveys were performed on the current status of applicable separation technologies for effective utilization of the hetero compounds of O and N contained in liquefied oil, the possibility of hetero compound utilization and issues in technological development for the utilization thereof. Since coal liquefied oil reflects greatly the coal composition and its structure, it contains generally a greater amount of hetero compounds, such as nitrogen and sulfur, as well as aromatic compounds than petroleum. If the hetero compounds could be removed from the liquefied oil more effectively before reforming as a result of progress in separation technologies, hydrogen consumption may be reduced. In addition, economic performance of the coal liquefaction business can be relatively improved by establishing a technology to utilize more effectively these by-products. The current fiscal year has performed surveys on the current status of technologies to separate oxygen and nitrogen in liquefied oil, the possibility of utilizing these hetero compounds, and issues in technological development for the utilization thereof. At the same time, surveys were carried out on the compositions, contents, and separation and analysis methods of hetero compounds in oil obtained by using the coal liquefaction systems being practically used. (NEDO)

Achievement report for fiscal 1998. Research and development of technologies for creating new organic electroluminescent devices (2nd fiscal year); 1998 nendo seika hokokusho. Shin'yuki electronics ruminessensu device no sosei gijutsu ni kansuru kenkyu kaihatsu (dai 2 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim of the efforts was to commercialize a multicolor, organic electroluminescent (EL) display and an energy efficient light source, to develop a highly efficient luminescent material, and to develop a protecting film for use in optical and electronic devices and technologies to seal the protecting film. Achievements in fiscal 1998 are mentioned below. The Kyushu office of Matsushita Electric Industrial Co., Ltd., manufactured a uniformly luminescent large screen, and Nisimu Electronic Industry Co., Ltd., fabricated a luminescent organic film by the wet method. As for materials, Dojindo mass-synthesized a hole transfer material, developed a new carrier transfer material, and developed a high-performance luminescent material. Daiden Co., Ltd., produced rare earth complexes and laminated pevskite. As for packaging technology, Shoei Chemical Co. developed a low-expansion glass filler, Kyushu University's Advanced Technology Joint Research Center formed an SiON protecting film on an EL device, and Fukuoka Mechanic and Electric Laboratory produced a DLC (diamond-like carbon) film. (NEDO)

Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Survey of natural gas technology trend); 2000 nendo choki energy gijutsu senryaku nadoni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (tennen gas gijutsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In search of new technical tasks involving the supply, transportation, and utilization of natural gas, a survey is conducted of the trend of natural gas supply and demand, trend of development of related technologies, and their impact on the market. After natural gas matters are outlined and definition and classification are established, investigations are conducted into natural gas production and the trend of new natural gas consuming countries supposedly to affect the natural gas supply and demand situation. Taken up as relevant technologies are cogeneration, natural gas powered automobiles, fuel cells, GTL (gas to liquid) technology, and micro gas turbines. These technologies are examined from the viewpoints of environmentally-friendliness and energy conservation feature, and then tasks to discharge are proposed in the fields of technology development, operation, and fuel. For natural gas powered automobiles, vehicular performance improvement and the conformability and standardization of high-pressure parts and components are taken up in the field of technology development, and the introduction and augmentation of quick fillers for natural gas and increase in the number of natural gas supply stations are taken up in the field of operation. Concerning fuel cells, in the field of fuels to be fed to the same, technologies of hydrogen storage and of refining and reforming of oil based fuels are taken up. (NEDO)

NEDO Forum 2001. Session on industrial technology development (Future of thing making and manufacturing/processing technologies); NEDO Forum 2001. Sangyo gijutsu kaihatsu session (monozukuri seisan kako gijutsu no mirai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. In a lecture entitled 'History of thing making,' the roles played by the now-defunct National Testing Laboratory and Industrial Test and Research Center were described and strategy for future development was predicted. In a lecture entitled 'Thing making and international apprentices competition,' apprenticeship training in practice at Denso Systems Corporation was presented. In a lecture entitled 'Key technology in thing making: outlook of metal mold industry,' shift in Japanese manufacturers' paradigm and change in metal mold marketing were explained, and the importance of reaching for the first position in the world in some specific fields or of expanding the scope of work in the entire value chain was stressed. In a lecture entitled 'Digital meister project: Aiming at amalgamation of IT (information technology) and MT (manufacturing technology),' database construction in the manufacture of metal molds, introduction of knowledge management systems, and development of CAD/CAM/CAE (computer-aided design/computer-aided manufacturing/computer-aided engineering) were discussed. (NEDO)

Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology - Research and survey of peripheral element technologies (Research and survey for development of solar cell of new power generation device structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu / shuhen yoso gijutsu ni kansuru chosa kenkyu (shinhatsuden soshi kozo taiyo denchi kaitaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Attention is paid to behavior at the molecular level with reference taken to the photosynthetic mechanism, and a behavioral mechanism is proposed, which incorporates, in place of the conventional band model, a concept of a molecular structure based on electron transfer, excitation energy transfer, and reactions of oxidation and reduction. Discussion is then made on elements of technology development for the embodiment of high-efficiency organic ferroelectric thin-film solar cells. The elements taken up include the feasibility of organic ferroelectric thin-film cells, photoelctric conversion systems of plants and photosynthetic bacteria, solar cells using donor-acceptor type dyes, organic thin-film solar cells using conductive polymers, and efficient photoexcitation of organic dyes. Fullerene compounds are semiconductive and their band gaps may be controlled to stay within the range of 0.75-1.9eV, and this justifies a hope that they will serve as solar cells. As for TPV (thermophotovoltaic) conversion, it is under development mainly at NASA (National Aeronautics and Space Administration) as a transportable power source based on heat of combustion. Efforts are also being exerted since 1990 in five European countries to develop TPV systems for small-scale cogeneration. (NEDO)

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-10-01

For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

Investigational research on CO2 isolation technology in fiscal 1995; 1995 nendo nisanka tanso no kakuri gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper studied present technical subjects and future study subjects of the CO2 isolation technology in order to clarify technical and social problems and the developmental subjects of the CO2 isolation technology and related technologies for separating/concentrating CO2 emitted in relation to quantity consumption of fossil fuel and storing it in ocean or underground. Main items for the study were: (1) investigational study of the technology of CO2 ocean storage, (2) investigational study of environmental effect assessment in storing CO2 in ocean, (3) investigational study of the technology of CO2 ocean storage, etc. Technologies required for the ocean isolation were arranged such as CO2 storage, injection, dispersion technique, CO2 behavior simulation, and the developmental subjects were extracted. Further, in the deep-sea bottom storage method, a simulation to calculate the range of PH effects was conducted presuming the specified amount of CO2 and applying known physical values, and evaluation of the CO2 ocean discharge/solution method was made. A method was also studied for experiments on water bacteria and benthos. 127 refs., 102 figs., 81 tabs.

Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsukui, R; Tsuru, T [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1996-05-01

The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

Study on a technology to afforest water level varying part of a reservoir; Chosuichi suii hendobu ryokuka gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onodera, O.; Matsubara, K.; Koyama, S. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1999-03-19

Equisetum was noted as a plant adaptable to stringent environment referred to as the water level varying part of a reservoir, and was used for afforestation trials. The afforestation trials were performed at the reservoir of Uryuu Dam No. 1 and the regulating reservoir of Moiwa Dam of Hokkaido Electric Power Company. Although the rate of water level variation is small at Uryuu Dam No. 1, it is necessary for Equisetum to withstand submergence and drought for an extended period of time. Moiwa Dam has high water level variation rate, but its water depth is small, and the reservoir is free of long-term submergence and drought. As a result of long-term observation from 1993 through 1997, Equisetum was found having grown well at lower altitude part with higher submergence frequency. It has grown favorably even in parts where submergence rate reaches about 80%. However, at higher altitude with submergence rate of 10% or lower, decrement trend was seen. At Moiwa Dam, Equisetum was all buried in accumulated sand and earth, revealing that such an environment is unsuitable for Equisetum as the one subject to effect of sand and earth that flow in during freshet. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of new building material integrated solar cell modules - investigation and research on analysis of practical application); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to promote the research to put new building material integrated solar cell modules into practical use, the following items were investigated: (1) functions and specifications for harmonizing with buildings, (2) new module materials that can respond to building materials, (3) marketability, (4) standardization of the assessment methods, (5) consistency with relevant legislation and related institutions, (6) effects on environment as building materials, and (7) investigation on technological trends inside and outside the country. In Item (1), the significance of developing the new building material integrated solar cell modules was made clear. In Item (2), the performance requirements on the currently used module materials were put into order. In Item (3), the market size was investigated, and assignments to establishing the market were put into order, such as the distribution and construction institutions, and assistance to the system introduction. In Item (4), standardization and unification of the assessment methods were discussed, and the items to be standardized were extracted. In Item (6), LCA on the currently used modules was performed. In Item (7), participation was made to the second solar beam power generation conference and EUROSUN '98; investigations were made on trends of developing the new building material integrated solar cell modules and how the recycling related legislation is being progressed; and the achievements in the development activities were confirmed, and the assignments were investigated at the new building material integrated solar cell module subcommittee. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of the new solar cell module integrated with construction materials - Investigative study on analysis for commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system, shuhen gijutsu no kenkyu kaihatsu (Shinkenzai ittaigata taiyodenchi mojuru no kenkyu kaihatsu - Jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the study for commercialization of the new module integrated with construction materials, survey of the technical trend of the new module integrated with construction materials in Japan and abroad was conducted, and the FY 2000 results were summarized. As to the module material correspondent to construction materials, the results of the survey made in the past three years were summarized, and the subjects to be considered in future were arranged from a viewpoint of disposal/recycle of modules. Concerning the marketability, various policies for the spread of solar cell module that is an immature good were arranged. Survey was also made of the photovoltaic power system using the field test project as a sample, and the following were made clear: The photovoltaic power generation has appeal for environmental consideration and energy conservation; In some cases, the power generation effect was not as much as expected because the information on design/construction is not sufficient. Relating to the evaluation of its effect on the environment, the paper summarized the environmental influence in each of the module methods at each stage of production/utilization/disposal and the basic items for measures to cope with the influence. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on environmental measures for compound solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - kagobutsu taiyo denchi module no kankyo taisaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research is conducted to properly deal with environmental problems, such as compromised solar cell safety, which may follow the mass introduction and diffusion of photovoltaic power systems. In the research of fiscal 1999 on technical literature on environmental measures against lead and animal tests, a need was found to reduce lead in power systems and to grasp lead elution characteristics for the establishment of environmental measures. In a safety test conducted for thin-film CIS (copper indium diselenide) based solar cells, basic data were collected about the vaporization rate of Se, the effect of moisture on the Se vaporization rate, etc. Basic data were also collected about the relationship between the combustion temperature and the amount of scattered lead in particular from the solder used as the conducting material in silicon based solar cells. In the evaluation of the environmental impact of thin-film CIS solar cells in case of fire, it was found that Se concentration below 10-20m in the plume was near the permissible concentration of 0.1mg/m{sup 3} as recommended by Japan Society for Occupational Health and that the concentration levels predicted for the periphery were two orders of magnitude smaller than the mandatory level. (NEDO)

Report on the results of the FY 1999 introductory R and D of MGC ultra-high efficiency turbine system technology. International cooperative project of MGC technology investigational study (R and D on advanced engine and energy saving use ceramics); 1999 nendo MGC chokokoritsu turbine system gijutsu sendo kenkyu kaihatsu seika hokokusho. MGC gijutsu chosa kenkyu kokusai kyoryoku jigyo (senshinteki engine oyobi sho energy yo yotoyo ceramics ni kansuru kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

As the R and D of advanced engine and energy saving use ceramics, this project is being conducted by the U.S., Germany, Sweden, Belgium and Japan under Annex II of the Committee of Energy Research Technology (CERT) established by International Energy Agency (IEA). For structure use ceramic materials, their raw material powder is tested and a method to evaluate characteristics of their sintered bodies is studied. The research was divided into Subtask 11 (test on mechanical characteristics) and Subtask 12 (evaluation of raw material powder). Each subtask decides on the details of the international joint research and the associated research assigned to each country. In the testing study on mechanical characteristics in this fiscal year, the evaluation method was studied of thermal characteristics of materials for heat resistant high temperature members. In the study for evaluation of raw material powder in this fiscal year, a method was studied for evaluation of characteristics of fine ceramic powder. The results to be obtained in this study are related to mechanical characteristics of materials for heat resistant high temperature members and to the basic evaluation method of characteristics of raw material powder. The results of the study are surely indispensable for promotion of the application of these materials. (NEDO)

Report of high efficiency waste power generation technology development in 1995; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (1995 nendo hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

High temperature and high pressure steam has been investigated for the high efficiency waste power generation technology development. The steam temperature below 300 centigrade is currently employed to avoid the corrosion of superheater, and the generating efficiency is less than 15%. Practical application of 500 centigrade and 100 kg/cm{sup 2} is planned by developing corrosion resistance materials. Environmental load reduction technology has been also developed. For the external circulation type fluidized bed furnace combustion tests using dummy waste in fiscal 1995, the temperature control at bag filter was effective for suppressing the dioxins. When using waste plastics, HCl could be reduced by blowing Ca compounds. Various Cr-Ni-Mo-based alloys have been developed as a corrosion resistance superheater tube material, and are currently tested. For the environmental load reduction technology, the development of pulse plasma exhaust gas treatment method has been continued from fiscal 1993. In fiscal 1995, this method was confirmed using a small-scale test unit, and also tested using a 5000 Nm{sup 3}/h bench-scale unit. The removal rates of dioxins at the outlet of bag filter were 99.8% and 99.3%, respectively. They were found to be affected greatly by the pulse waveform. 13 refs., 107 figs., 24 tabs.

NEDO Forum 2001. Session on advanced power generation and storage technology development; NEDO Forum 2001. Shindenryoku gijutsu kaihatsu session

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-20

The presentations made at the above-named session and remarks made at the panel discussion of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Predicted by Deputy Chairman Tanaka of International Superconductivity Technology Center in his lecture entitled 'Energy problem in IT (information technology) oriented society' were that possibilities were high that power consumption would rapidly increase in line with the progress of broad band and wireless, that energy conservation and environmental technologies should be developed urgently, and that superconductivity technology would assume an important role. Discussed at the panel on 'Prospect of distributed power sources in power systems' were 'Power utilization by information communication in IT-oriented days and needs for development,' 'Energy utilization involving buildings and needs for development,' 'Tasks to discharge in cogeneration technology development and coordination with power systems,' 'Technical problems involving interconnection of distributed power sources and needs for development,' 'Present state of distributed power sources and needs for development,' and 'From Fuel and Storage Technology Development Department to Advanced Power Generation and Storage Technology Development Department.' (NEDO)

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (low-cost Si sheets by continuous casting method); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (renzoku cast ho ni yoru tei cost Si kiban seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on manufacturing of low-cost Si substrates by continuous casting method in fiscal 1994. (1) On manufacturing of ingots of 16 piece size, the ingot of nearly 170kg was manufactured by batch process using the Si melt injection unit prepared in last year. (2) On oxygen and carbon contents in wafers, the contents were measured by FT-IR after slicing of the ingot. As a result, the oxygen and carbon contents could be successfully reduced to the targets of 10ppma and 5ppma or less, respectively. (3) The resistivity distribution of the ingot ranged over the target of 1-2ohm-cm. (4) Cells of 100 {times} 100mm{sup 2} wide and 350{mu}m thick were verified by in-house evaluation process. Although lower cell conversion efficiency was found at the center top of the ingot, a vertical efficiency stability was nearly sufficient as a whole. (5) On the crystal growth unit prepared in fiscal 1994, any problems were not found on automatic driving and vibration during moving. 8 figs.

Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. R and D of high-performance industrial furnaces, etc; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho). Koseino kogyoro nado ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

Report on results of development of fuel cell power generation technology 1998. Research and development on polymer electrolyte fuel cell (technological development of element, research on ion exchange membrane for practicability of high performance cell); 1998 nendo seika hokokusho. Nenryo denchi hatsuden gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, yoso kenkyu kaihatsu (koseino denchi jitsuyoka no tame no ion kokan maku ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This paper explains the results during fiscal 1998 of ion exchange membranes in the development of polymer electrolyte fuel cells. Studies were made on three kinds of standard and two kinds of experimental membranes selected among the Flemion membranes, which are perfluorosulfonic acid membranes made by Asahi Glass Co.,Ltd., and also on the Nafion membranes by Dupon as reference. As the resistance evaluation of the environmental cycle for the membranes, a temperature cycle test was carried out, with the characteristics measured such as moisture content, membrane resistance, mechanical properties, and gas permeability, so that the effects were examined of the temperature cycle on the membranes. Evaluation was also commenced on the water permeability, an important substance-moving characteristic of ion exchange membranes. In the evaluation of the characteristics of membrane-electrode assemblies, the environmental cycle test was performed by joining electrodes to membranes, with the evaluation similarly made as for the membranes alone. On the basis of a correlation between the water permeability and the cell performance, studies were made on the effect of thickness of the membranes on the cell performances. A continuous stability/durability operation of 3,500 hours was verified using Flemion R. As for membrane reinforcement, studies were continued on the cloth and fibril reinforcements as in the previous year.(NEDO)

Industrial science and technology research and development institutions in fiscal 2000. Research and development of human media (Report on achievements in research and development of high-level information system for petroleum plant); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho (sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Having selected a petroleum refining plant as a large and complex system, a system was developed, that is capable of operating safely and efficiently a plant even by young operators by utilizing the human media technology that realizes information environment having a sense of unity with humans. With this system, if an anomaly is detected in the plant condition, the agent and the operator talk with each other freely, and necessary items of information are displayed on a large screen from moment to moment according to the priority thereof. Activities were taken in the following nine areas: 1) the total system, 2) research on an interface agent, 3) research on hypothetic plant indication interface, 4) research on a discrete cooperative treatment technology, 5) research on plant models and interface systems, 6) research on plant ontology, 7) research on significance indication interface, 8) improvement of tools to structure a large-screen integrated indication system, and 9) investigations on technological trends in foreign countries. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths (Development of technology to produce geothermal resources in great depths); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop geothermal resources, research and development has been performed on the production technologies for the deep-seated geothermal resources, such as pressure, temperature, flow speed and density (PTSD) logging technologies. This paper summarizes the achievements in fiscal 1999. In the actual well test on the developed D-probe, it was verified that the probe operates normally under high temperature environment (342 degrees C) which exceeds the measurement limit of conductive cables (315 degrees C). In developing the PTC monitoring technology, the downhole sampler was improved, and a test was performed in the actual hole in the Hijiori area in Yamagata Prefecture. As a result, collection of hot water of about 900 mL has become possible. In developing the high-temperature tracer monitoring technology, simulation was performed keeping in mind charging the tracer into the Hijiori geothermal area, whereas specifications for charging and collecting the tracer were determined. In developing the scale monitoring technology, experiments were carried out on the fluid systems under deep geothermal conditions by using scale forming devices, by which it was indicated that silica is the important scale constituent. (NEDO)

Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and increase in density of matrixes, and harmonization with long fibers. Silicon nitride was trially made with low lubrication/friction coefficients and high strength. A simulation method for crack progress behavior evaluation was developed using a testing notched specimen heterogeneous microstructures. Analyses were made of brittle fracture mechanics and reliability evaluation. 273 refs., 344 figs., 29 tabs.

Fiscal 1997 report on the results of the cooperative research project under consignment from NEDO on technology for simply setting-up of the molding conditions of engineering plastics; 1997 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (Engineering plastic no seikei joken kan`i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A cooperative research project was carried out between Japan and Thailand with the aim of developing a system which can simply set up molding conditions using as elements the technology on mold design and injection molding in plastic parts production and the experiment/evaluation technology for making sure of the quality of molded products. In fiscal 1997, based on the basic plan worked out in the previous fiscal year, molding equipment, auxiliary equipment, mold, experimental equipment, injection molding CEA system, etc. were installed at Thailand`s BSID (Bureau of Supporting Industries Development). Supported by equipment manufacturers, the technical guidance was given for operation/maintenance/control of all equipment. At the same time, researchers were sent from Japan, and the joint research was started. Japan received three researchers from BSID for training of molding technology, injection molding CEA program use technology, and experimental evaluation technology. The engineering plastics used for study are polyacetal, polyamide and polycarbonate. 17 refs., 68 figs., 14 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Report on achievements in fiscal 1998. Development of useful substance production technology utilizing gene combination technology; 1998 nendo idenshi kumikae gijutsu wo riyoshita yuyo busshitsu seisan gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In developing a useful substance producing technology utilizing gene combination technology, plants are taken as a kind of useful substance producing arena, wherein useful protein genes of animals are introduced and manifested in the plants. Thereupon, technological development was carried out for the following items with regard to mass production of useful substances that can be utilized industrially, such as cytokine, by means of plant and cell cultivation: 1. Development of a useful substance producing technology utilizing gene combination technology, and 2. Comprehensive surveys and researches. For the technology to obtain and design useful substance producing genes originated from animals, development of a technology to search and acquire useful genes originated from animals, and a design and modification technology for useful genes. For the technology to introduce genes into gene combined plants, creation of plants combined with useful substance producing genes, and development of an introduction technology using plant virus vector. For the technology to produce high-function chemical substances in the gene combined plants, establishment of technologies for mass breeding and activity analysis of gene combined plants and cultivated cells, and for extraction and refinement of useful substances from the gene combined plants. In the comprehensive surveys and researches, technologies were surveyed and items of information were collected inside and outside the country. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / R and D on downsizing technology of machine tools (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / kosaku kikai no downsizing gijutsu ni kansuru kenkyu kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D were conducted aiming at downsizing machine tools by combining microfactory technology owned by Mechanical Engineering Laboratory, Agency of Industrial Science and Technology of MITI with fundamental element technology owned by industrial groups of machine tools. In fiscal 1997, as to the study of spindle drum indexing mechanism in making main spindle multiaxial, the following have been finished: the basic study through openness of controller and networks, confirmation of function of the equipment acquired, and initialization of the driver software. Relating to the study on machining conditions of dry machining processing, delivery and installation of cold air machining instrument have been finished. Concerning the optical measurement of spindle radial run-out vectors, a system to make optical no contact measurement of radial direction components of rotation error was constructed with high accuracy pin gauge attached to the work spindle clamp mechanism as a medium. About the study on sensor-based state recognition technology, specifications for various kinds of sensor were decided on. 5 refs., 67 figs., 3 tabs.

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Research cooperation of the development of laser radar for environmental measurements; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Research and development of the laser radar for measuring the air pollution in urban areas and the environmental information network have been conducted through the cooperation with Indonesian researchers. A measurement system suitable to actual situation of Indonesia has been constructed. In FY 1996, some works have been conducted as in the final fiscal year. To set the laser radar for environmental measurements and to make a plan of measurement research, conditions of air pollution in Indonesia and setting places of systems have been investigated. Opinions for the cooperation research have been exchanged with Indonesian researchers. Actual trends of the environmental measurements technology using laser radar have been surveyed. Indonesian researchers have been invited to learn operation and data processing of the system. One unit of MIE diffusion laser radar system has been designed and fabricated, and an additional data processing program has been made. The system has been delivered to Jakarta and installed. After the adjustment, performance tests have been conducted to complete the construction of the system. 3 refs., 72 figs., 10 tabs.

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power generation system evaluation technology (Research and development of system evaluation technology - Separate volume: Collection of data of photovoltaic power generation systems); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu - Bessatsu: taiyoko hatsuden system data shu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the establishment of technologies for optimum designs and optimum operation for various types of photovoltaic power systems, data are compiled in this volume, collected from the field test facilities and residential photovoltaic power systems. Operating data and meteorological data from the field test facilities (interconnection system, independent system, and water pump system) are arranged as easy-to-use supplementary data to help studies in relation to the 'energy flow in the test field facility systems' which is in the fiscal 1999 achievement report. As for data collected from residential photovoltaic power systems, they are arranged as easy-to-use supplementary data to help studies in relation to the 'Data and evaluation of residential photovoltaic power systems' which again belongs in the fiscal 1999 achievement report. (NEDO)

Report on achievements in fiscal 1999 on research and development of immediately effective and innovative energy environment technology. Part 1. Development of immediately effective and high-efficiency solar cells, and development of technology to slice and manufacture thin-type large-area polycrystalline substrates; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (usugata daimenseki takessho kiban slice seizo gijutsu kaihatsu 1)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of decreasing silicon usage quantity for the purpose of reducing the solar cell production cost, development is being performed on an ingot cutting technology to cut a silicon ingot to Kerf loss of 150 {mu} m and thickness of 150 {mu} m, and in which the produced wafers can withstand the cell making. Investigations revealed that a wire saw is suitable as the cutting system, and the wire used must have a diameter of less than 120 {mu} m, and a strength of more than 3850 N/mm{sup 2}. A prototype wire was fabricated, whose diameter is 120 {mu} m, and in which the strength is distributed between 3870 and 4110 N/mm{sup 2}. It was found possible that a wire of 160 {mu} m can be used to slice an ingot having a cross section surface of 150 mm square and a length of 300 mm into a slice having a Kerf loss of 200 {mu} m and a thickness of 180 {mu} m. This wafer had the in-plane distribution of the substrate thickness at {+-} 12.5 {mu}, swell of 120 {mu} at maximum, and surface roughness of 5 {mu}. Making ten of these wafers into a cell resulted in a yield of 60%. Assignments are the clarification of the properties of the cutting wire, the preparation of a thin wire with homogeneous quality, and the establishment of a technology to cut Kerf loss of 150 {mu} and substrate thickness of 150 {mu}. (NEDO)

Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy (Textile technology field)); 1999 nendo choki energy gijutsu senryku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a textile technology field. Social demand and constraint in the 21st century restrict human life and industrial activity, however, include huge business chances. This technology strategy aims at construction of textile business contributing to the society, and improvement of the international competitiveness of Japanese textile industry. Analysis was made on the current international competitiveness of the textile industry in comparison between Japanese and American productivity. As factors hindering technological innovation, the following were pointed out: poor cooperation among industry, academia and government, poor cooperation among different kinds of industries, poor preparation of basic technology, knowledge base and creation base, and poor deregulation. As the future target and strategy, 7 technology targets, 2 creation targets, and every target year were showed. 4 proposals were also showed as follows: preparation of a technology base, creation base, talent education and knowledge base, and protection of intellectual property rights. (NEDO)

Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Iron and steel technology field; 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) (tekko gijutsu bun'ya)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a steel technology field. Japanese steel industry should correspond to requirements of the international economic society as the top runner. Although it is now difficult to suppose a basic technology innovation, stable supply of basic materials is necessary for peripheral industries. The basic raw material technology is the basis of domestic and overseas socio- economic activities. The technology development support system to retain the world-wide leadership of Japanese industries is a strategic issue. Preparation of cooperative R and D bases of industry, academia and government along a national policy is important. Strong promotion of such national projects is also essential as global environment problem, positive use of advanced information tools, development of technologies and products of unexplored fields, and development of new products and demand creation according to social needs. Such measures along social requirements are also important as raw material development to double an energy efficiency, and the policy and system to construct a recycling society and living spaces. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Report on development of high-efficiency wastes power generation technology in fiscal 1998. 1. Development of component technology, and demonstration test of a pilot plant; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Yoso gijutsu kaihatsu (pilot plant jissho shiken) (dai 1 bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A technology is developed to perform high-efficiency power generation by generating high-temperature and high-pressure steam stably by burning general wastes and combustible industrial wastes as fuel. This paper describes summary of the achievements in fiscal 1998. Corrosion tests were performed on over-heater materials under steam condition of 500 degrees C and 100 kg/cm{sup 2} by using a hot model. It was verified by the tests that the corrosion environment around an external heat exchanger is milder than that with an external stack. A circulation fluid bed was simulated from operation data, and a prospect was obtained on steam conditions required for the high-efficiency power generation. In order to elucidate the corrosion mechanism, discussions were given on deposited ash properties, corrosion characteristics and stress. Elucidation was made on a discharge chamber structure most suitable for removing dioxins and NOx by using a waste gas treatment process that uses plasma generated by discharge. A concept design was made. The economic effect of the system is equivalent to that of the activated carbon blow-in process, whereas a waste gas treatment system was nearly completed. As a result of the pilot plant test, the power generation efficiency is estimated to be 30% in a scale of 1200 tons per 24 hours. A demonstration test revealed that dioxin emission was far below the regulation value. An optimal system was also discussed. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

Survey report for fiscal 1993 on development of coal and brown coal liquefaction technologies. Part 2. Survey of economic efficiency of brown coal liquefaction process; 1993 nendo sekitan ekika gijutsu kaihatsu kattan ekika gijutsu no kaihatsu chosa hokokusho. 2. Kattan ekika process no keizaisei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Financial assessment is carried out by estimating the liquefaction product cost (selling price) at which the predetermined rate of return on investment is to be earned, which is calculated by the DCF (discount cash flow) method. The cash flow is determined from the net after taxes for each business year, and the balance after the subtraction of long- and short-term borrowings is converted to the present worth as of the operation commencement year at the predetermined discount rate, and a total is calculated for the period. When the difference between the total and the equity does not vanish, the coal liquid selling price is changed, and this process is repeated until the difference vanishes. If a 20% reduction in the plant construction cost is feasible, the coal liquefaction product will be competing with the crude oil in the market in around 2030. Although the financial analysis is a profitability analysis from the fund providers' viewpoint, the benefit as seen from the project siting country needs to be assessed by an economic analysis, and probabilities are that, in the presence of great profits, the project will materialize if the two are found to earn more than average after the profits are impartially divided. Japan's benefits and expenditures are compared and subjected to an economic analysis, and a result of 6-15% is obtained. This means that the project will realize in case EIRR (economic internal rate of return) is higher than the fund procuring cost of 11%. (NEDO)

FY 1999 report on the result for research and development of instantaneously effective and innovative energy and environment technology. Development of technology to use combustible wastes as resources and fuels; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu kanengomi saishigen nenryoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Manufacturing compressed fuel, or refuse paper and plastic fuel (RPF) from combustible wastes such as used papers and waste plastics to utilize them effectively as a fuel to substitute fossil fuels is regarded as a promising engagement. However, this process indispensably requires removal of chlorine contained in used papers and waste plastics to a degree that they do not impede the combustion. The present research and development is intended to develop a PRF pretreatment technology and a dechlorination technology, and establish a technology to utilize the materials as resources and fuels as thermal recycling of combustible wastes. The current fiscal year has performed research and development on the following themes: development of a sorting system and a crushing system in developing the pretreatment technology, whereas for the former system, sorting tests were carried out by using a vibration type wind power sorting machine and an inertia force wind power sorting machine, and for the latter system, data were obtained on the crushing characteristics; dechlorination tests, in which it was discovered that the mixing ratio of used paper in the material affects the chlorine concentration; research on combustion characteristics, in which fundamental combustion tests using a small fluidized bed, combustion tests using a bench scale fluidized bed, and stoker fired furnace combustion tests were performed; and demonstrative operation researches. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

FY 1999 report on the results of the development of recycling technology of waste architectural materials, glass, etc. Development of the simple glass coloring/decoloring technology; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kan'igata glass chakudasshoku gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of increasing the ratio of recycling of waste architectural materials, glass, etc., the development was proceeded with of easy coloring of colorless glass by light irradiation and decoloring of it by heat treatment. The important point for technical development is to develop glass materials which are colored by light and decolored by heat at a level of technique with practicality and to develop coloring/decoloring device. Studies were made in the following three fields: 1) optimization of coloring/decoloring conditions for coloring/decoloring occurring from defects (color centers) under light irradiation; 2) optimization of coloring/decoloring conditions occurring from colorless ions and particulate formation under light irradiation; 3) development of a visible drawing device. In 1), bottle, sheet glass, and soda-lime silicate glass are colored brown by X-ray/UV radiation, but the coloring is bad in stability. However, it was found that the addition of silver oxide improved stability. In 2), it was recognized that when the glass containing a trace of Mn was melted in the reducing atmosphere, it became colorless, and when radiated by X-ray and heat-treated at approximately 200 degrees C, it was colored bluish violet which was vivid and stable. (NEDO)

Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

Fiscal 1997 research report on development of use technology of bio-resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho (fukugo seibutsukei riyo seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report summarizes the fiscal 1997 research results on production technology of functional materials, and the research study result for utilizing substance production and decomposition by complex biosystem for industries. For detecting technique of microorganisms in soil, staining by CFDA-AM was suitable, and allowed visualization of sulfate- reducing bacteria during culture. For research on functional analysis technology, study was made on atomic force microscope technology to detect microorganisms in environment and observe their fine structures. For research on detection, separation and cultivation technology of difficult-to-culture microorganisms, a molecular genetic analysis method of microbial communities and a determination method of their viability were selected. For functional substance production technology, study was made on technical utilization of bioflocculant produced by microbial consortia as environment-friendly oil removal reagent, and on gene transfer control in microbial consortia. For the research study for the project, survey was made on useful substances produced by complex biosystem. (NEDO)

Survey report for fiscal 1993 on development of coal and brown coal liquefaction technologies. Part 2. Survey of economic efficiency of brown coal liquefaction process; 1993 nendo sekitan ekika gijutsu kaihatsu kattan ekika gijutsu no kaihatsu chosa hokokusho. 2. Kattan ekika process no keizaisei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Financial assessment is carried out by estimating the liquefaction product cost (selling price) at which the predetermined rate of return on investment is to be earned, which is calculated by the DCF (discount cash flow) method. The cash flow is determined from the net after taxes for each business year, and the balance after the subtraction of long- and short-term borrowings is converted to the present worth as of the operation commencement year at the predetermined discount rate, and a total is calculated for the period. When the difference between the total and the equity does not vanish, the coal liquid selling price is changed, and this process is repeated until the difference vanishes. If a 20% reduction in the plant construction cost is feasible, the coal liquefaction product will be competing with the crude oil in the market in around 2030. Although the financial analysis is a profitability analysis from the fund providers' viewpoint, the benefit as seen from the project siting country needs to be assessed by an economic analysis, and probabilities are that, in the presence of great profits, the project will materialize if the two are found to earn more than average after the profits are impartially divided. Japan's benefits and expenditures are compared and subjected to an economic analysis, and a result of 6-15% is obtained. This means that the project will realize in case EIRR (economic internal rate of return) is higher than the fund procuring cost of 11%. (NEDO)

Report on the research and development under a consignment from NEDO of high temperature carbon dioxide fixation and utilization technology for fiscal 1996; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku gyomu seika hokokusho. Nisanka tanso koon bunri kaishu sairiyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the prevention of global warming, this R and D is aimed at separating/recovering high temperature CO2 from high temperature gas at 300degC or above and developing technology for effective use of the recovered CO2 as measures taken for reduction in CO2 emissions from the fixed emission sources. In this fiscal year, the following were proceeded with: heightening of separation performance evaluation technology, promotion of technical development of ceramic separation membranes and supports, and development of element technology of modular integration. In the examinational research on separation technology and system optimization, the following were conducted: survey of trends of the technical development, conceptual design of plant and prediction of process behavior, assessment of applicability of the process, and study of effects of utilization/spread of the developmental technology. In the former R and D, borosilicate glass powder rich in alkali is formed on the ring by joining the trially manufactured hollow fiber type membrane and the same form alumina cylinder, and sealing property and strength which stand measurement of permeability were confirmed. In the latter, an innovative process applied with CO2 high temperature separation technology was studied to examine effects of the spread of high temperature gas separation technology. 403 refs., 478 figs., 134 tabs.

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a voluminous cell incubation technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research and development in fiscal 1981 on the 'voluminous cell incubation technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. In the research of a method for producing industrial materials using cells originated from lymph-based trunk cells, researches were performed on selection and breeding of cells, development of serum-free media, and establishment of the optimal culture method with regard to the method for producing industrial materials using stocks producing virus induced interferon. Regarding the method for producing industrial materials using idio-interferon producing mutable stocks, research and development was made on selection and breeding of superior cell stocks and serum-free media. With regard to the method for producing industrial materials using marrow originated cells, such researches were carried out as technological investigations, collection of cells, establishment of the proliferating condition for myeloid leukemia cells, discussions on the assay method for differentiation inducing factors, and search for cells producing useful substances. Other activities include research of the method for producing industrial materials using cells originated from epithelium cells, information exchange on voluminous cell incubation technologies, and investigations on literatures and patents. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of ultrahigh-efficiency crystalline compound solar cell manufacturing technology; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Efforts are made to develop a GaInP/GaAs-based compound semiconductor solar cell built on an Si substrate, the Si substrate being lower in cost, higher in mechanical strength, lighter in weight, and higher in heat conductivity than a GaAs or Ge substrate. Fiscal 1999 studies involved improvement on GaAs/Si heteroepitaxial growth and the evaluation of crystallinity in thus grown layers, improvement on cell characteristics, fabrication and evaluation of an n{sup +}/p structure cell, and so forth. As for crystal growing technologies, a 980 degree C 5-heat-cycle annealing method was applied, and the density of dislocation was reduced to 5 times 10{sup 6}cm{sup -2}. In the fabrication of cells, an n{sup +}/p structure cell was studied, and the cell achieved 12.5mAcm{sup -2} in short-circuit photoelectric current over 9mAcm{sup -2} of the conventional p{sup +}/n structure GaInP cell. Without any special effort to optimize the structure, a GaInP/GaAs layer-built cell on a GaAs substrate achieved 23.7% in conversion efficiency. When it is taken into consideration that conversion efficiency on an Si substrate is approximately 80% of what is achieved on a GaAs substrate, it is deemed that the achievement of 23.7% suggests that near 20% in conversion efficiency may become available on an Si substrate. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the consortium based analysis technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made to look for the consortium based analysis technology by which the consortium base can be analyzed as it is using the molecular biological method. Studies were made in the following four fields: 1) new identification technology of eucaryote using II DNA topoisomerase genes (PCR amplification method of II DNA topoisomerase genes); 2) method to detect new recognition peptide activated microorganism (adjustment of cortical antigen); 3) technology to elucidate detection/response mechanism of the specific environment and adaptation/resistance mechanism of the specific environment; 4) incubation method inside 3D matrices. In 3), studies were made of the analysis of inhibition mechanism of korormicin and separation of solvent-resistant oil degradable bacteria. In 4), for the settlement and dynamic analysis of microorganism consortium by studying incubation conditions, conducted was the molecular system analysis of bacteria and eumycetes inhabiting in sponge. (NEDO)

FY 1998 annual summary report on manipulation of atomic and molecular extremes. Development of technologies for high-efficiency analysis/manipulation of DNA and the like; 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to establish the techniques for observation/manipulation of atoms and molecules, as the common basic techniques for various industrial areas, e.g., new materials, electronics, biotechnology and chemical. Development of atomic field and scanning tunneling microscopes working under extreme conditions has been pursued, in order to manipulate complex systems, such as living body. For identification of molecular species, laser-excited fluorescence is combined with scanning mechanical probing to further refine the single molecule detection/identification techniques, and the objectives are set to develop a new method for evaluating molecules in a living body using a scanning probe microscope, and also to develop a novel scanning probe microscope for molecules in a living body. The other efforts were directed to R and D of the techniques for observing structures of organic molecules and the like through the measurements of adsorption process of organic molecules and clusters on semiconductor substrates and their surface reactions, and precision measurements of vibrational conditions of adsorbed molecular species reacting in the solid-liquid interfaces by high-sensitivity Raman spectroscopy to elucidate the catalysis mechanisms at the molecular level. (NEDO)

Achievement report for fiscal 1987 on the entrusted research and development of basic technologies for next-generation industries. Research and development of technologies of mass culture of cells; 1987 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The aim is to add value to the chemical industry by establishing technologies for realizing a large and stable supply of fine chemical products whose industrial production is difficult when conventional techniques are applied, the products including various useful substances yielded by animal cells including those of man. To fulfill the aim, efforts are exerted to complete basic technologies involving the mass culture of cells through conducting researches into animal biofunctions. This report covers the endeavors made in fiscal 1987 under the above-named project created in fiscal 1981. All the subject matters are for the development of substance production methods for industrial use, and include the studies of use of optimal cultivation methods mainly for serumless cultures and cultivation engineering, studies centering on the high-density cultivation of cells and serumless cultures, studies using suspended and quasi-suspended cell lines, studies using cells deriving from bone marrow, and studies using epithelial cells. Furthermore, the results are outlined of the comprehensive researches conducted into technologies of mass cultivation of cells. (NEDO)

Fiscal 1994 report on results of R and D on new forming technology of composite materials. Development of innovative technology for producing members for high efficiency power generation; 1994 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Activities were conducted in the three areas of (1) R and D on ceramic matrix composite forming technology, (2) R and D on metallic matrix composite forming technology, and (3) comprehensive investigation and adjustment, for the purpose of developing materials that manifest superplasticity among ceramic and metallic matrix composites as well as developing the forming and fabrication technology and also of improving productivity by simplifying the fabrication processes. In (1), upon discovering that the superplastic properties of zirconia (3Y-ZrO{sub 2}) sold in the market is affected by the grain size and impurities (Al{sub 2}O{sub 3}) of the material, a zirconia was developed in which a trace of Al{sub 2}O{sub 3} and SiO{sub 2} were added, with a method detected capable of the fabrication through a low deforming stress. In (2), development was carried forward for a new high specific strength high-temperature material applicable to aircraft engines for example, as well as its forming and fabrication technology, by making a composite between metals and between metal and ceramics by a mechanical alloying (MA) method. Metalcarbide, nitride and oxide made by the MA method were sintered by hot press or the like, and a sintered material was thereby obtained that was superplastic and capable of the near net-shape forming. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1995. 2. Main subject (Part 1. Physiologic indexing technology); 1995 nendo ningen kankaku kesoku oyo gijutsu no kenkyu kaihatsu. 2. Honronhen (Seiri shihyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This paper describes the physiological indexing technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1995. In work stress evaluation using mainly autonomic nervous system indexes, factors for the work stresses were extracted and experimental environments were put in order in applying the technology to the indexing at higher levels and the coordinative works. Use of common primary indexes was introduced for transitory stress, and the common primary indexes were introduced also for chronic stress. In the stress evaluation using composite physiological function measurement, data analyses were made, and discussions were given on the time series basis on the action indexes and the physiological indexes as the work performance of a work load assigning work to elucidate points of the problems. In stress indexing using skin temperatures, a possibility was obtained in indexing by using the skin temperatures on transitory stresses during tension and monotonous work. Measurement of stresses with hormone placed as the main subject tries to apply to human being the changes in hormones which have been verified since quite some time ago by animal experiments. However, it is difficult to find a definite trend because of complexity of stresses in the human society. For the basic arousal indexing, studies were made on improvement of accuracy of the monitor and quantification of actions of physical stimulation. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 8) - development of hydrogen production technology; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 8. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

R and D was conducted with the view of establishing hydrogen production technology based on the solid high polymer electrolyte water electrolysis method, which presumably offers higher efficiency and lower cost than conventional methods. This year, as well as implementing development of large-scale cell lamination (electrode area 2,500 cm{sup 2}, 10 cells) by using two hydrogen production methods (electroless plating method and hot press method), work was started for developing cells (electrode area 1,000 cm{sup 2}) for hydrogen stations. In the research on longterm durability improvement, with a 50 cm{sup 2} membrane electrolyte or cell, the evaluation test results were obtained of stable electrolytic performance showing more than 93% energy efficiency after 400 hour operation, under the conditions with electrolysis pressure 0.4MPa and electrolysis temperature 120 degree C. In a test of 1,000 cm{sup 2} prototype cell for hydrogen stations, the evaluation result was obtained for energy efficiency of 92% under the conditions with electrolysis pressure 0.5MPa and electrolysis temperature 120 degree C; thus, this year's target efficiency of over 90% was achieved. Further, enhancement of the quality was contrived for example by improving the electroless plating method and remodeling a roll press machine. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a voluminous cell incubation technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Saibo tairyo baiyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research and development in fiscal 1981 on the 'voluminous cell incubation technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. In the research of a method for producing industrial materials using cells originated from lymph-based trunk cells, researches were performed on selection and breeding of cells, development of serum-free media, and establishment of the optimal culture method with regard to the method for producing industrial materials using stocks producing virus induced interferon. Regarding the method for producing industrial materials using idio-interferon producing mutable stocks, research and development was made on selection and breeding of superior cell stocks and serum-free media. With regard to the method for producing industrial materials using marrow originated cells, such researches were carried out as technological investigations, collection of cells, establishment of the proliferating condition for myeloid leukemia cells, discussions on the assay method for differentiation inducing factors, and search for cells producing useful substances. Other activities include research of the method for producing industrial materials using cells originated from epithelium cells, information exchange on voluminous cell incubation technologies, and investigations on literatures and patents. (NEDO)

Fiscal 2000 report on results of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of technology for innovative metallic material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of obtaining higher strength/toughness in metallic materials, R and D was conducted concerning nano-sized grain refining and bulk forming by micro-grain dispersion, with fiscal 2000 results compiled. In {gamma} stainless steel, development was conducted using SUS304 as the base material, revealing that ZrC was effective for forming a micro-crystallized grain structure. In addition, it was found feasible that precipitation behavior of carbide was controllable through a temperature rising process at the time of solidification forming. In an HIP+ (hot isostatic pressing) hot forged material with ZrC finely dispersed, it characteristically showed an average crystalline grain size of about 300 nm, a tensile strength of 1,085 MPa, and a Charpy impact value of 1.86 MJ/m{sup 2}. Further, in thin plates micro-crystallized by thermo-mechanical treatment using martensite reverse transformation, a strain rate sensitivity index m value became 0.3 or higher at a strain rate of 10{sup -2}S{sup -1}, indicating manifestation of superplasticity. In {sigma} stainless steel, TiO{sub 2} and ZrO{sub 2} were examined for their effect of suppressing grain growth on the basis of SUS410. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 1); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The achievements during fiscal 1993 of research and development on a method to evaluate warm heat comfort by living scenes of workers by using a human body thermal model included completion of a human thermal model introduced with physiological knowledge such as artery-vein anastomosed (AVA) blood vessels and two-system blood circulation net. The effectiveness of the model was experimented and verified. It was made possible to estimate the reversal phenomenon occurring in hot heat environment, in which skin temperatures at peripheral body parts rise higher than those in the body trunk part, and skin temperature distribution. In the correlation study to estimate statistically the sense volume from skin temperatures, it was possible to estimate significantly different sense volumes from face skin temperatures, but the estimation accuracy was low because of such factors as difference in individuals. What is important in enhancing the accuracy is to identify ecological reactions of human being caused from change in the sense volume, select effective parameters, and study the mechanisms. In order to develop stress relaxing scents, discussions were given on degree of subjectivity stress by question papers and cortisol concentration in saliva as the parameters. An experimental system was developed to measure the effects of the scents to relax work stresses. A screening method was developed, whereas effects of 15 kinds of scent materials were investigated. (NEDO)

FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of developing the industrial utilization technology, analysis was made of functions and interactions of the specified functional biological groups, and at the same time the developmental study was made of the technology to isolate/culture the constitutive biological groups. The FY 1998 results were summed up. As to the technology to detect microorganisms in soil, the SFDA method was improved and the new dyeing method was developed. And, there almost was hope for the development. Concerning the functional analysis technology, the functional substances peculiarly manifested only in the complex system in the ocean environment are searched. Several kinds of compounds were found out, and at the same time the test to confirm the biological activity is under way. Relating to the isolation/culture technology, study was made on rotten fruit, and the existence in the sample of the microorganisms which are difficult in isolation/culture was newly confirmed. In regard to the culture of the microorganisms which are difficult in isolation/culture, availability of the replica method was found out. As to the technology to produce functional substances, studies were made on the following: utilization technology of the environmental harmony type oil/water separation polymer producing microbial consortia, method to artificially make gene exchanges in the microbial consortia, etc. (NEDO)

1998 report on results of research and development on new venture type industrial science and technology. 'Technological development of super metal' (technological development of innovative metallic material); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Results on 1998 research and development were summarized concerning the technological development of innovative metallic materials. In the research of particulate micro-diffusion technology, as a modeling of nano-structure holding process, Ag/Fe nano-crystal alloy was manufactured by inert gas vapor deposition, with the structural change at the time of rolling examined. In addition, a large-scale spark plasma sintering device was developed, with a 40mm diameter cylinder manufactured. In the research on crystal grain refining process by a stirring solidification method, crystal grain refining was achieved to 1{mu}m order. In the development of an advanced aluminum alloy forming method, concerning a high-speed superplastic molding technology, a basic evaluation test was carried out for the superplastic characteristics of rapidly solidified aluminum alloy continuously from fiscal 1997. Further, a calculator simulation was performed by the finite element method for the high-speed superplastic molding. From these results, knowledge was obtained necessary for the detailed design of a high-speed superplastic molding device. On the basis of this knowledge, manufacturing of the equipment was implemented, as were the introduction, rise, basic test, etc. (NEDO)

Project to aid development of an oil substituting fuel manufacturing technology in fiscal 1998. Report on the result of developing a technology to make cable covering materials into fuel; 1998 nendo sekiyu daitai nenryo seizo gijutsu kaihatsu hojo jigyo. Densen hifukuzai nenryoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development have been carried out with an objective to re-utilize waste cable covering materials as oil substituting energy. The research has been performed on behavior of chlorine and lead being substances that impede making the cable covering materials into fuel, development of a technology to remove chlorine, lead and copper, and pelletizing properties for fuel making. In the study of behavior of chlorine and lead, the following matters were made clear: dechlorination reaction completes within 30 minutes if pyrolysis temperature is higher than 300 degrees C; the more the amount of filler CaCO3 in test samples, the less the dechlorination amount; and secular deterioration does not affect the dechlorination amount. A technology has been developed successfully to remove the substances that hinder making the cover materials into fuel, achieving the target values of copper at 0.2% or less, lead at 0.3% or less, and chlorine at 5% or less. In developing the pelletizing technology that puts the cover materials into raw materials for blast furnaces, dechlorination rate of 90% was achieved by mixing coke/PVC at a ratio of 1/1 and dechlorinating it by using a rotary kiln. It was verified that the product is free of problems in particle size as the blast furnace raw material. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1993. 4. Research and development of correlation and evaluation technology (Part 2); Ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 4. Sokan hyoka gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Developments were performed during fiscal 1993 on a system to investigate correlation among external stimulating environment, physiological effects and sense volume based on a physiological reaction model. The development works included improvement of the model, discussions on a method to estimate parameters inside living organisms, and a method to collect subjectivity volume data. Prototypes thereof were fabricated, evaluated, and experimented, where nearly complete achievement of the targeted functions was verified. In developing a technology to evaluate quantitatively the comfort of composite environments composed mainly of warm heat environment, discussions were given on an integration evaluating expression in order not to make handling the environmental physical volume too complex. The expression models the evaluation of governing sense volume in individual environments of warm heat, light beam, and sound, and calculates the composite environment evaluation indexes by using the evaluation indexes obtained from the modeling as the descriptive variables. In developing the space-type human interface adapted to human senses, a computer system to realize the interface and the platform for function mounting were developed. The development items were broken down respectively on the basic technologies for functional aspect and surveillance and control function mounting, and the software systems. The human comfort meter achieved the basic design target. (NEDO)

Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the technology to use high grade functions of the bioconsortia system, the R and D were conducted, and the FY 1998 results were summed up. As to the study of functional material producing technology, screening of the 2400 strains owned by Marine Biotechnology Institute was conducted using reporter strain, and about 400 strains of homoserine lactone producing bacteria which are interbiological information convey substances were obtained. Concerning the effective decomposing/purifying technology of petroleum products, study of petroleum decomposition analysis technology was finished in the development of culture/control technology of petroleum decomposition microbial consortia constitutive bacteria. Relating to the analysis of the petroleum decomposition microbial consortia, changes in the bacteria population at the site of the heavy oil pollution accident on the Sea of Japan were investigated for the past one year by the PCR/DGGE method. It was found out that levels of the oil pollution in ocean could be assessed by measuring the concentration of Alcanivorax. As to the technology for highly utilizing unused petroleum fractions, conducted were the chemical analysis of photolytic crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Research on engineering methods for cost effective PV installation; Shuhen gijutsu no kenkyu kaihatsu. Tashu secchi koho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of engineering methods for photovoltaic power system installation in fiscal 1994. (1) On the survey on applicable fields, various application aspects, applicability, and problems on location and legal regulation were continuously studied for railway, river reservation, lake surface and public facility as promising locations after highway in the last fiscal year. The result pointed out relatively easy possibility of PV power generation of nearly 11,700MW except residence and building fields. (2) On installation technology of solar cell arrays, several models based on various installation conditions, construction methods and system configurations were studied, and various application aspects were proposed by combination of simple design conditions. (3) On test and evaluation of the structural design of array racks, wind tunnel experiments were conducted for structure wall, platform shed and highway sound insulation wall. (4) On basic design of various promising systems, the conceptual design of interconnection systems was carried out assuming applications to highway and railway. 7 figs., 3 tabs.

FY 2000 report on the survey on the long-term energy technology strategy, etc. - Basement technology for implementation of industrial technology strategy. Survey on the extraction of preferential important technical subjects in FY 2002; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho - sangyo gijutsu senryaku sakutei kiban chosa. 2002 nendo yusenteki juyo gijutsu kadai no chushutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey is to investigate the consciousness of researchers and engineers of enterprises, universities, etc, of the importance of about 100 important technical subjects in 'the industrial technology strategy' prepared by the Ministry of Economy, Trade and Industry. In the questionnaire survey, the following were selected: 1)systematization of policy in consideration of the social needs and R and D of the technology to realize it; 2) R and D of the technology to advance the future frontier; 3) technical subjects that the government should promptly start to tackle in each classification in arrangement of the intellectual basis. Answers to the following items were obtained: 'selection reasons' for why it was considered important in each technical subject, 'lead time' toward the time of the industrialization, 'international positioning' of Japan against Western countries, 'possibility of heightening/maintaining the international competitive force,' and 'items that the government should participate in.' In 1), the following four big targets were arranged: 'security/safety,' 'informatization,' 'environment' and 'energy'. In 2), the following technical subjects were arranged: 'biotechnology,' 'information communication technology,' 'production technology,' 'materials/process technology,' 'energy/environment' and 'new blending/traversable/integrated technology.' In the results of the survey, analyzed were big targets, and trends and characteristics at technical field levels. (NEDO)

FY 2000 research and development of fundamental technologies for AC superconducting power devices. R and D of fundamental technologies for superconducting power cables and faults current limiters, R and D of superconducting magnets for power applications, and study on the total systems and related subjects; 2000 nendo koryu chodendo denryoku kiki kiban gijutsu kenkyu kaihatsu seika hokokusho. Chodendo soden cable kiban gijutsu no kenkyu kaihatsu, chodendo genryuki kiban gijutsu no kenkyu kaihatsu, denryokuyo chodendo magnet no kenkyu kaihatsu, total system nado no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for research and development of fundamental technologies for AC superconducting power devices has been started, and the FY 2000 results are reported. The R and D of fundamental technologies for superconducting power cables include grasping the mechanical characteristics associated with integration necessary for fabrication of large current capacity and long cables; development of barrier cable materials by various methods; and development of short insulated tubes as cooling technology for long superconducting cables, and grasping its thermal/mechanical characteristics. The R and D of faults current limiters include introduction of the unit for superconducting film fabrication, determination of the structures and layouts for large currents, and improvement of performance of each device for high voltages. R and D of superconducting magnets for power applications include grasping the fundamental characteristics of insulation at cryogenic temperature, completion of the insulation designs for high voltage/current lead bushing, and development of prototype sub-cooled nitrogen cooling unit for cooling each AC power device. Study on the total systems and related subjects include analysis for stabilization of the group model systems, to confirm improved voltage stability when the superconducting cable is in service. (NEDO)

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 2. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo 2))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 1. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo-1))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-01

Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

Fiscal 1999 research cooperation project report. Research cooperation on coal liquefaction technology; 1999 nendo sekitan ekika gijutsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research cooperation project result on coal liquefaction technology. Cooperative FS was made on coal liquefaction technology of Indonesian coal as petroleum substituting energy. To obtain the basic data necessary for the FS, study was made on the applicability of Indonesian natural minerals as catalytic materials. Promising low-cost abundant Soroako Limonite ore showed a high catalytic activity for liquefaction reaction of Banko coal, and an excellent grindability. Improved BCL process including hydrogenation process was promising for production of high-quality coal liquid superior in storage stability with less nitrogen and sulfur contents. Survey was made on the general conditions of Tanjung Enim area including South Banko coal field concerned, and the geological features and coal seam of South Banko coal field which is composed of 3 seams including coal deposits of 6.35 hundred million tons. To study the marketability of coal liquid, survey was made on the current situation of oil, oil product standards, and blendability of coal liquid. Hydrogen for the liquefaction process can be obtained by coal gasification. (NEDO)

Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

Fiscal 1997 survey report. Survey on the innovative well drilling technology; 1997 nendo chosa hokokusho. Kakushinteki kosei kussaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In the geothermal drilling, reduction of the cost of well drilling is an important subject for technical development. The geothermal resource development tends to be made at higher temperatures and at deeper wells. In the present drilling technology, the cost is rising with the exponentially increasing depth and temperature, and there is also occurring the technical limit. Accordingly, the survey clarified the limit of the present drilling technology/cost to point out the research trend of the drilling technology as substitute for the present one, possibilities of the introduction, and the R and D target and subjects. As to latest drilling systems abroad and in Japan, the following were surveyed to study and extract promising technologies and systems: improvement/application of drilling equipment/materials (enhancement of heat resistance of the main drilling equipment, etc., cooling effects of top drive, heat resistance verification of MWD tools, PDM, tricone bits, multi-stage cementing tools, etc.), heightening of drilling rates, trend surveys of slim hole drilling, control drilling, well maintenance/workover, and well design technology. 68 refs., 73 figs., 40 tabs.

Fiscal 2000 survey report. Survey and study of constellation satellites technology; 2000 nendo chosa hokokusho. Konsutereshon eisei gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demands for constellation satellites were surveyed and satellite systems were studied for extracting basic technical tasks relative to constellation satellite systems and for drafting space verification plans. For a constellation satellite system to accomplish its missions, two or more satellites have to be simultaneously navigated. It is assumed that its field of application will cover earth observation, information communication, risk management, disaster prevention, and the like. With such applications taken into consideration, surveys and studies were conducted about the need and marketability of constellation satellites, need of state-level involvement, and requests for missions to be imposed on a constellation system. For plural satellites to satisfy mission requests by coordinating with each other, it will be necessary to develop basic technologies, such as navigational guidance, communications control, system autonomous management, and operation on the ground. Functions and performance that a constellation satellite system are requested to have and basic technologies to be studied and developed were extracted, and space verification plans were drafted. (NEDO)

Research cooperation promotion business for fiscal 1998. Research cooperation in the development of environmentally-friendly high-efficiency mineral resources extracting and processing technologies; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation was conducted in the Republic of Kazakhstan for efficiently extracting and collecting valuable metals (gold, silver, copper, and rare metals) contained in volume in the slag generated by mining operation, with caution exercised not to disturb the environment. The research items taken up for development involved technologies of the leaching of the target elements using sulfuric acid, microbes, etc.; extraction using solvents; electroextraction; collection of gold and silver; and the treatment of waste water. In fiscal 1998, the wet process and the processing of gold and silver were studied, for which the specimens sampled at the research site in and after fiscal 1996 were used. As for the fabrication of pilot plant facilities, all were completed in fiscal 1998, and part of them was transported to the research site. Procurement and transportation necessary for the joint research were also carried out. Furthermore, to ensure effective execution of the project, scientists were invited from Vniitsvetmet, the Kazakhstan research institute for non-ferrous metals, for training, who included the institute director, deputy director, patent/liaison department chief, and two researchers. (NEDO)

Report on achievements in fiscal 1979 in Sunshine Project. Development of a high-temperature ground layer drilling technology (feasibility study on high-temperature ground layer drilling); 1979 nendo koon chiso kussaku gijutsu no kaihatsu seika hokokusho. Koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

This paper reports research achievements on the following items: (1) a roller cutter bit, (2) solid bit and air friction bit, and (3) bit materials. In Item 1, fabrication and test were performed on a roller cutter bit on which studies were made for use, heat treatment, and manufacturing method of improved heat resistant steels. Effects were obtained in tip retention force when high-temperature rocks are drilled. Research and development was made on construction of a bearing as a friction type bit, in which dry bearing pressed in with a solid lubricating agent was inserted into an outer race. In Item 2, an indoor drilling test was carried out on a solid bit using two-layered ultra hard tip. A durability test on an air friction bit bearing recognized no wear on a check after operation of about 40 hours under a load of 3 tons and at a rotation speed of 80 rpm. Thus, the bearing was considered sufficiently reliable from the aspect of durability. In mud water drilling in the field, some wear was observed in the thrust direction. In Item 3, studies were performed on heat and corrosion resistant tip materials, bit materials using heat resistant alloys, improvement in bearing materials, strengthening of inside of a cutter made of metallurgically sintered powder, provision of heat resistance onto bit materials, indoor cutting tests, and seals for bits. (NEDO)

Fiscal 1997 report on the results of the R and D on the invention of high-level combustion technology using the microgravity environment; 1997 nendo seika hokokusho (bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of achieving both the diversification of energy resources and the reduction in environmental pollutants in fuel exhaust gases, the paper conducted elucidation of combustion phenomena using microgravity facilities and research on combustors which make high-level combustion possible. In the experimental study using microgravity experimental facilities, conducted were evaluation experiments on combustion/evaporation of fuel droplets and droplet groups, elucidation/evaluation experiments of combustion characteristics of high-density fuels, evaluation experiments of flammability limit, and elucidation/evaluation experiments of emission mechanisms of NOx, etc. Analysis/evaluation of the data obtained and elucidation of the combustion mechanism were conducted. Further, by applying the results of the microgravity experiment, the high-level combustor experimental facilities were fabricated, and validation tests were started. In the international joint research with US`s NASA, the following were conducted using JAMIC`s facilities and NASA`s 2.2 second drop tower: study of mutual interference of droplet series combustion, study of binary system fuel droplet series combustion, study of combustion characteristics of solid fuels, study of behavior of flames around the lean flammable limit, etc. 151 refs., 253 figs., 7 tabs.

Investigation on application of coal ash, lime and gypsum-based compositions. ; Development of technology to utilize and dispose of used desulfurizing agnet. Sekitanbaiter dot sekkaiter dot sekkokei soseibutsu no oyo ni kansuru chosa. ; Shiyozumi datsuryu zai no riyo shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Mori, K. (The Hokkaido Electric Power Co. Inc., Sapporo (Japan))

1991-11-20

This paper describes the result of an investigation by testing on re-utilizing the used desulfurizing agent discharged from a thermal power plant as a sludge disposer and a deodorant. The used desulfurizing agent used in the test is a nearly neutral substance composed mainly of SiO{sub 2} and CaSO{sub 4}. The paper describes that the tested agent has a character to solidify when added with water, and the solidified substance made from the agent added into a sludge is nearly neutral and usable in the similar manner as in the commercially available sludge solidifying materials. The paper also reports that in a field test for applying this tested agent to cover the sludge surface, a marked effect of improving water quality was recognized, including the increased water transparency. It also states that the tested agent absorbs ammonia actively, and that as a result of investigating its applicability as a deodorant for pet excreta odors, the agent can be handled more easily than the commercially available deodorants and has a deodorizing effect equivalent to or better than them. 4 refs., 7 figs., 6 tabs.

NEDO Forum 2000. Geothermal technology development session (new development of geothermal energy); Chinetsu gijutsu kaihatsu session. Chinetsu energy no shintenkai

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The following themes were presented at this session: (1) geothermal development in the future, (2) the current status of geothermal development and utilization, (3) surveys on the promotion of geothermal development, and (4) verification and investigation on geothermal exploration technologies, development of hot water utilizing power generation plants, and international cooperation on geothermal development and utilization. In Item 2, report was made on the current status of geothermal power plants in Japan and their future development targets, long-term overview of geothermal development, measures and budgets to achieve the targets of geothermal development. In Item 3, it is reported that out of 48 areas completed of the survey (including the new promotion surveyed areas), the areas possible of steam power generation and confirmed of temperatures higher than 200 degrees C are 30 areas, and the areas possible of binary power generation (using down hole pumps) and small to medium scale power generation, confirmed of temperatures of 100 to 200 degrees C are 13 areas. In Item 4, reports were made on the reservoir bed variation exploring method, surveys on deep geothermal resources, a 10-MW demonstration plant, a system to detect well bottom information during excavation of geothermal wells, a technology to collect deep geothermal resources, and a hot-rock using power generation system. In Item 5, geothermal exploration in remote islands in the eastern part of Indonesia, and the IEA cooperation projects were reported. (NEDO)

FY1995 development of a novel rapid immunoassay technology; 1995 nendo shinkina kosoku men'eki sokutei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

By utilizing the phenomenon that the antigen induces association of VH and VL, which are the antigen-recognizing fragments of antibody, develop a novel rapid immunoassay technology which will eliminate the defects of conventional immunoassays, such as long measuring time and requirement of expensive large automated apparatus. In addition, develop a methodology to make Fvs with low VH-VL affinity but that associate tightly in the presence of antigen. Using a model anti-hen egg lysozyme antibody HyHEL-10 Fv and BlAcore, we have clarified the kinetic basis of the Fv stabilization by HEL. By labeling HyHEL-10 VH, VL with succinimide esters of fluorescein and tetramethylrhodamin, respectively, at their N-termini, we could successfully detect VH-VL association by the increment of fluorescence resonance energy transfer. As a result, 1 {mu} g/ml of antigen could be detected homogeneously in less than 5 minutes. Some VH-VL association measurement systems were made by utilizing M13 phage display of VH fragments of HyHEL-10, anti-nitrophenacetyl, anti-digoxin antibodies. (NEDO)

Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

Execution management of batter piles and problems of technical development. Uchikomi kui no seko kanri to gijutsu kaihatsu no kadai

Energy Technology Data Exchange (ETDEWEB)

Ninomiya, Y [JDC Corp., Tokyo (Japan); Omori, H [Nippon Kokan Koji K.K., Yokohama (Japan)

1991-05-15

This report introduces the practical examples of the present system of execution manegement. Necessary functions and basic problems are described as well as the possibility of utilizing hydraulic/pneumatic pressure for the automation or the robotization which are the future technical problems. Application examples are also shown on the execution management system by means of an accelometer which was developed by the authors. This area is not long after the start of study. Essential points of the execution management of the batter piles are that the front tips of the piles are confirmed to be securely penetrated to the specified depth in the specific support layer giving the required supporting strength at the same time. For this purpose, what are required are to accurately measure the penetration displacement of the piles and assess the maximum penetration and final penetration and the amount of the rebound. Then the support strength should be checked from the dynamic support force. For this, it is required to develop an execution management system which is simple and adept for the operation at the spot. 9 refs., 12 figs., 5 tabs.

Basic research program for innovated coal utilization in Japan. BRAIN-C program; Sekitan riyo kiban gijutsu kaihatsu. BRAIN-C program

Energy Technology Data Exchange (ETDEWEB)

Harada, M [Center for Coal Utilization, Japan, Tokyo (Japan)

1996-09-01

This paper introduces the circumstances and purpose of establishing the Basic Research Associate for Innovated Coal Utilization (BRAIN-C) Program started in October 1995, and the summary of the results therefrom in fiscal 1995. Although development of coal utilization technologies has been implemented over a number of years, there are many problems still requiring solutions. Early realization has been urged on diversification of coal utilization, acceleration of technological development and diversification of coal types. In order to achieve these goals, the necessity was recognized afresh on not only the hardwares, but also on basic technologies in terms of software which can identify properties of coals, systematize different reactions, and estimate reactions, fluidity and heat transmission of coals. Therefore, receiving a subsidy from the Agency of Natural Resources and Energy of the Ministry of International Trade and Industry, a research and development program to be implemented jointly by industries, administrative agencies and academic societies had been started with a five-year plan for the time being. With the activities for the program such as collecting 50 to 100 types of coals and supplying them to researchers, the program had been accelerated in fiscal 1995 on a large number of themes and results therefrom, including fundamental properties and thermo-chemical reactions. 2 figs., 4 tabs.

Development of regeneration technique for diesel particulate filter made of porous metal; Kinzoku takotai DPF no saisei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yoro, K; Ban, S; Ooka, T; Saito, H; Oji, M; Nakajima, S; Okamoto, S [Sumitomo Electric Industries, Ltd., Osaka (Japan)

1997-10-01

We have developed the diesel particulate filter (DPF) in which porous metal is used for a filter because of its high thermal conductivity and a radiation heater is used for a regeneration device because of its uniform thermal distribution. In the case high trapping efficiency is required, filter thickness should be thick. The thicker filter has a disadvantage of difficulty in regeneration because of the thermal distribution in the direction of thickness. In order to improve regeneration efficiency, we designed the best filter-heater construction which achieves uniform thermal distribution by using computer simulation and we confirmed good regeneration efficiency in the experiment. 4 refs., 14 figs., 1 tab.

Development of novel processes for Cu concentrates without producing sulfuric acid; Hiryusan hasseigata no atarashii doshigen shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, T; Noguchi, F; Takasu, T; Ito, H [Kyushu Inst. of Technology, Kitakyushu (Japan). Faculty of Engineering

1997-02-01

In the refining process for the production of copper from pyrites, heat treatment is carried out in a neutral atmosphere so that part of the sulphur will be collected in the form of simple sulfur and that pyrites naturally low in reactivity will be made active. A basic study is also conducted of a very high speed electrolytic method. The chemical aspects of pyrites which are various in composition (mainly CuFeS2) are clarified by X-ray diffraction, and then is subjected to heat-treatment in a 773K-1073K argon atmosphere. There is a decrease in the amount of sulfur at a temperatures not lower than 973K. The X-ray main diffraction line splits for the emergence of some lower angle diffraction lines. The specimen is then subjected to a leach test in a copper chloride base liquor, to disclose that leachability grows remarkably higher in the presence of a great change in the X-ray diffraction lattice constant. An experiment follows in which an electrolyte is allowed to flow at a high speed for accelerating the rate of electrolytic refining in an effort to prevent the passivation of anode and deposition of dendrite on the cathode that is apt to occur when the current density is high. Passivation is prevented when the flow rate is 10m/min or higher in the vicinity of the anode surface for the formation of a smooth electrodeposited surface. 2 refs., 2 figs., 2 tabs.

Development of novel processes for Cu concentrates without producing sulfuric acid; Hiryusan hasseigata no atarashii doshigen shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Awakura, Y; Hirato, T [Kyoto University, Kyoto (Japan)

1997-02-01

Studies are conducted to develop a new wet method for copper concentrates to replace the conventional dry smelting method for the settlement of problems involving the processing of impurities for environmental protection. A specimen of pyrites polycrystals is subjected to leaching at 80 {degree}C in a strongly acidic cupric solution. Findings are that the element sulfur generated in this process does not impede leaching and only approximately 4% of the sulfur is oxidized into sulfur ions; that the presence of more than 2g/liter of bromide ions produced during bromine-aid leaching of gold changes the structure of sulfur for the inhibition of leaching; that circulation of a bromine-containing leaching liquid is not desired since even a small amount of approximately 0.02mol/liter inhibits the leaching rate. Controlled potential electrolysis is performed for the anode in an acid solution containing CuCl, NaCl, and NaBr, for the observation of oxidation/reduction potentials predicted by Nernst`s equation. It is then disclosed that bromine is more effective than chlorine in gold leaching and that the solution potential during leaching agent regeneration enables the monitoring of solution constitution. 2 refs.

Fiscal 1999 research achievement report on the development of SNPs related technologies; 1999 nendo SNPs kanren gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop specimen processing technologies for modifying and enabling various kinds of specimens to automatically undergo SNP (single nucleotide polymorphism) analysis for medicine development and clinical diagnostic activities and to develop technologies and apparatuses to enable rapid, inexpensive, and simple search and analysis of SNPs using DNA (deoxyribonucleic acid) chips and mass spectrometry. Activities are conducted in the four fields involving (1) the development of a practical clinical system for rapid detection and analysis of SNPs, (2) research and development of an SNP scoring system using bar-coded oligonucleotides and magnetic beads, (3) research and development of a high-speed SNP analysis system using a mass spectrometer, and (4) the development of a high throughput SNP analysis line. Efforts exerted in field (1) involve a protein fixation method using plasma polymerization and its application to DNA arrays, development of an SNP detection method using human genomes, construction of a rapid DNA detection device using an electric field, development of an SNP analysis system using the solid phase HPA (hybridization protection assay) method, and SNP analysis using solid phase ligation. (NEDO)

Present situation of technical development to cope with CO sub 2 exhaust. CO sub 2 taisaku gijutsu kaihatsu no genjo

Energy Technology Data Exchange (ETDEWEB)

Sema, T [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1991-04-01

A quantitative evaluation was made on techniques of CO{sub 2} immobilization utilizing organisms by referring to literatures. The techniques used for the evaluation were the following six ones: The first one is to plant trees on wastelands located in the tropics and the subtropics and CO{sub 2} is immobilized by grown trees. The second one is to compulsorily blow CO{sub 2} into water to immobilize CO{sub 2} by multiplicated microorganisms such as green algae. The third one is to multipulicate phytoplanktons by spraying deficient trace elements on oceans where trace elements such as Fe are deficient in spite of rich nutritive salts to absorb and immobilize CO{sub 2}in seawater. The fourth one is to multipulicate shellfishes in coastal regions to immobilize CO{sub 2} in seawater as their shells. The fifth one is to multipulicate many coral reefs in tropic or subtropic coastal regions to immobilize CO{sub 2} as calcium carbonate. The sixth one is to multipulicate large size seaseeds such as giant kelps in shallow seawaters to immobilize CO{sub 2} in seawater. The width of each applicabe area, immibilizingcapability of CO{sub 2} and the executing cost were considered to evaluate respective methods. As a result, the multipulication of marine planktons were thought most promising. 1 fig., 4 tabs.

Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

Results of the supplementary work to the fiscal 1994 New Sunshine Project. Development of geothermal power plants, etc. (development of production, technology for deep-seated geothermal resources); 1994 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant to kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reports on the fiscal 1994 results of the study of the development of a technology for collecting deep-seated geothermal resources, which has been made for increasing the capacity of the geothermal power generation as a part of the New Sunshine Project. As a plan for the development, a development is made of logging equipment and its auxiliary system and then characteristics of the deep-seated geothermal well are clarified. The logging equipment is a PTSD (pressure/temperature/spinner flow-meter/fluid density) logger which stands the use at deep-seated geothermal wells of 400{degree}C and 490 kgf/cm{sup 2} and measures pressure, temperature, flow rate and fluid density under static and dynamic conditions. In this fiscal year, metal seals were developed for preventing geothermal fluids from penetrating into the PT probe. Qualities and inner/outer diameters of various kinds of structural materials used in the S probe were determined, and output necessary enough to detect the rotation number is obtained. Measuring precision of D logging by {gamma} rays was evaluated. The study was made of the monitoring technology including the borehole and ground measuring system, the borehole fluid sampling and the scale formation. Relating to the tracer widely used in monitoring of hydrothermal reservoirs, investigated was the trend of the technology from abroad. 8 refs., 60 figs., 26 tabs.

Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research, development, and survey of crystalline solar cell evaluation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (kesshokei taiyo denchi hyoka system no kenkyu kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the basic study of ultrahigh-efficiency cells, the technology of ribbon crystal growing is again attracting attention for shortage of Si material supply. The new technology and problems to solve for cost reduction for it are discussed. Concerning the bulk type crystalline Si which is a core material, recent trends are mentioned involving studies of basic substrate properties such as the photoabsorption coefficient and crystal defects for achieving higher efficiency, development of gettering and surface passivation technologies, enhancement of processing speeds, radiation concentration behavior, etc. Newly obtained findings about photodegradation are mentioned, and some remedial measures are described. Recent reports on the application of porous Si to solar cells are compiled. In connection with the development of low-cost quantity-production process technologies, a remarkable progress recently marked by polycrystalline Si solar cells is described. Furthermore, it is stated that new process technologies will be required in the fields of material refining, substrate manufacturing, and cell fabrication. A proposition is presented aiming at developing cell modules compatible with application systems and practicalizing modules that may be integrated with roofing materials. Reference is also made to surveys overseas. (NEDO)

Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of high- efficiency production process technology); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on R and D of laser processing technology, in-situ measurement technology, and generation and control technology of photon as laser beam source, for energy saving and efficiency improvement of energy-consumptive production processes such as welding, jointing, surface treatment and fine particle fabrication. The research was carried out by a technical center, 9 companies and a university as contract research. The research themes are as follows: (1) Processing technology: simulation technology for laser welding phenomena, synthesis technology for quantum dot functional structures, and fabrication technology for functional composite materials, (2) In-situ measurement technology: fine particle element and size measurement technology, (3) All- solid state laser technology: efficient rod type LD-pumping laser module, pumping chamber of slab type laser, improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology, fabrication technology for nonlinear crystals, and high-efficiency harmonic generation technology. Comprehensive survey was also made on high- efficiency photon generation technologies. (NEDO)

Fiscal 1999 achievement report on research and development of industrial technologies. Research and development of synergy ceramics; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are conducted in the two fields of (1) survey and research and (2) development of technology for evaluating high temperature dynamic corrosion characteristics of heat resistant ceramics. In field (1), a comprehensive survey is conducted, an application study is conducted about high temperature gas separating ceramic membranes, and efforts are made to put to practical use ceramic parts manufactured by a low cost production process. In the application study of ceramic membranes, technologies are developed for a process of manufacturing high temperature gas separating porous ceramic membranes capable of separating and purifying gas emissions and gas ingredients, which involves the development of technologies for improving on gas separation and purification functions, development of technology of providing catalyst support function, technology of porous membrane formation, evaluation of separation characteristics, and so forth. In an application study for ceramic parts manufactured by a low cost manufacturing process, which involves structural ceramics, optimization is accomplished for materials synthesizing technologies by means of mechanical alloying, and cylinder liners are fabricated and evaluated for a natural gas engine made of silicon nitride based ceramics. In field (2), a high temperature dynamic corrosion testing device is built for heat shield coatings. (NEDO)

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Aerospace technology field (Aircraft technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kokuki gijutsu bun'ya))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 basic research result on industrial technology strategy of an aircraft technology field. In an aircraft field, since the major theme is application of new technologies to new airframe development, with joining in international cooperative development of aircraft, Japanese initiative development of airframes based on the domestic market demands and profitability should be started as early as possible. Because there is no airframe development by only one country including U.S.A., Japan is profitable to unite with some overseas companies, and invest selectively in specific leading fields. Positive technical support to safety, reliability, comfort and environment harmony are also important. More important theme than establishment of elementary technologies is preparation of an integrated flight demonstration system to expand application chances of development results, and preparation of various test facilities for tests required during development activities. Application of information technologies to the whole aircraft industry, and organic cooperation between the private and public sectors are also important. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of practical application of integrated solid waste recycling technique using highly developed equipment for waste water; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kokinoka kaishu mizushori system wo mochiita saishigen shori gijutsu no jitsuyoka ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to dry and pulverize into PDS (pulverized dry sludge) the waste (concrete sludge) discharged from ready-mixed concrete plants, and to develop its practical application. The fine sand component contained in the waste water after washing is removed to the maximum extent, and high-quality sludge-based PDS suitable for reuse is recovered. The process comprises an aggregate recovery stage, fine sand removing stage, coagulation/sedimentation stage, dewatering stage, crushing stage, drying stage, and a collection stage. High-quality PDS contains 30-40 mass% of CaO and 10-20 mass% of SiO{sub 2}, and its particles have an average diameter of 3-20{mu}m and an average specific surface area of 5,000-30,000cm{sup 2}/g. A particle is roundish with its angles rounded off. As for the fine sand component, not less than 90% thereof is removed by a wet cyclone method, and the water is collected and supplied for PDS manufacture. The development is already complete of powder and liquid coagulants, of which not less than 96% is inorganic, as coagulants exclusively for use for concrete. The quality of the manufactured PDS fulfills the target values, and it is concluded that PDS is recyclable like blast furnace slag or fly ash. (NEDO)

Fiscal 1999 research report on long-term energy technology strategy. Pt. 2. Basic research on industrial technology strategy (Individual technology strategy.) Material technology field (Fine ceramics); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 2. Sangyo gijutsu senryaku sakutei kiban chosa (bun'ya betsu gijutsu senryaku) zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the basic research result on industrial technology strategy for a glass field. Japan is facing such various economic problems as attack by developing countries, collapse of economic babble and yen's appreciation, and environment problems over a period of several years, and a glass industry is also under the influence of such problems. For continuous development of Japan and improvement of the international competitiveness of Japan, development of a glass industry is essential. Both co- possession of technical issues by cooperation of the members, and breakdown of conventional structures of the industry are necessary. Clarification of technical issues, and cooperation of industry, academia and government is essential. The current state, promise and issues of domestic and overseas glass technology and its R and D are described. The joint target of an industrial strategy for researchers and engineers of every sector, and the approach to such target are showed from the viewpoint of the issues for Japan and preparation of common basic technology. The role of each sector for environment preparation and policy is described to achieve the target. (NEDO)

Research and development on a single-frequency simultaneous two-way cellular wireless device; Ichishuha doji sohoko ido musenki ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A cellular wireless device performs signal transmission and receiving using only one assigned frequency because of effective frequency utilization, and therefore, is inconvenient in actual use. For this reason, a cellular wireless device operating on a new principle was developed to make simultaneous two-way calls possible on one frequency. The operation principle is such that one frequency is used, voice signal is divided on the transmission side at every 0.4 second, compressed in time to 1/2, and transmitted in 0.2 second upon modulation; and the receiving side extends the signal to a double length upon demodulation to take out the original voice signal. Thus, the transmission time is reduced to half, and the remaining half time thus obtained is assigned to the receiving time from a caller in the similar method to perform a two-way simultaneous call. Both hands can be used freely during a call, making the safe call possible even while driving a vehicle or performing a work. High confidentiality can be maintained by means of voice processing, compression, and extension. Size of the device was reduced, reliability and clarity were optimized, and a large number of frequency can be switched easily. Field test have proved that the device meets the criteria specified in the Electric Wave Law. The device was begun of business use in 1992. It can be connected with portable type telephone sets and those used in business compounds. 2 figs.

Report on evaluation of research and development of superhigh-function electronic computers; Chokoseino denshi keisanki no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1973-02-20

Described herein is development of superhigh-function electronic computers.This project was implemented on a 6-year joint project, beginning in FY 1966, by the government, industrial and academic circles, with the objective to develop standard, large-size computers comparable with those of the world's highest functions by the beginning of the 70's. The computers developed by this project met almost all of the specifications of the world's representative, large-size commercial computers, partly surpassing the world's machine. In particular, integration of the virtual memory, buffer memory and multi-processor functions, which were considered to be the central technical features of the computers of the next generation, into one system was a Japan's unique concept, not seen in other countries. The other developments considered to have great ripple effects are seen in LSI's, and techniques for utilizing and mounting them and for improving their reliability. Development of magnetic discs is another notable result for the peripheral devices. Development of the input/output devices was started to correspond to inputting, outputting and reading Chinese characters, which are characteristics of Japan. The software developed has sufficient functions for common use and is considered to be the world's leading, large-size operating system, although evaluation thereof largely awaits the actual specification results. (NEDO)

Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

Report on achievements of research and development of a technology to apply human senses to measurements in fiscal 1992. 3. Research and development of a simulated environment presenting technology; 1992 nendo ningen kankaku keisoku oyo gijutsu no kenkyu kaihatsu. 3. Mogi kankyo teiji gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the simulated environment presenting technology, extracted from the achievements in the development of a technology to apply human senses to measurements in fiscal 1992. Methods to present, evaluate and improve composite acoustic environment handle the effects compounded of air propagating sound, solid propagating sound, and low frequency sound, and researches are being performed to elucidate noise evaluation indexes. A composite acoustic environment presenting device was designed, part of which has been fabricated. In the research of a radiation model that serves for enhancing working environment, development was made on a manually controlled artificial sunlight radiation device model. To simulate the kaleidoscopically changing spectral radiation intensity in the nature, the existing filters are insufficient, and development of a new system was necessary. Therefore, the developed and fabricated artificial sunlight radiation device was provided with a function that can simulate different natural sun beams in the manner of envelope approximation. In addition, the device was provided with ultra-violet ray cutting function to make it safe for human body. In the research of high-accuracy real visual sense recognition, a high-speed prototyping system, an improved sensor system, and a contact software were prepared. The intended targets were basically achieved. (NEDO)

Fiscal 1993 report on technological results. R and D on new forming technology of composite materials (Development of innovative technology for producing members for high efficiency power generation); 1993 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

A forming technology was developed which uses superplasticity of composite materials, i.e., high-functional materials for power generating equipment for example. Activities were conducted in the three areas of (1) ceramic based composite materials, (2) development of metal-based composite forming technology, and (3) comprehensive investigation and adjustment. In (1), with a view to finding a composite forming technology, in which high tenacity materials are obtained by evenly dispersing particles or whiskers as reinforcements in a matrix, a room temperature forming technique using fine particles was exploited, as were a high temperature forming technique using fused bodies and a possibility of manifestation of superplasticity in the prepared composite materials. The materials used were Si{sub 3}N{sub 4} matrix-SiC, Al{sub 2}O{sub 3} matrix-TiC, and glass matrix composite based materials filling ceramics in fine holes of porous glass. In (2), composite forming technologies were examined for such composite materials as Al alloy matrix-SiC particulate-based by a molten metal stirring method, Al alloy matrix-ceramics short fiber-based by a high pressure forging method, Ti alloy matrix-ceramics particulate-based by a mechanical alloying method, and Al alloy matrix-ceramics particulate-based by an alkoxide method/powder metallurgy method. (NEDO)

FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

In the study of a corrosion resistant high sensitivity gas sensor, the following two technologies are needed: decrease in impurities of materials for super-higher purity, and formation of films with physically high quality such as orientation and homogeneity. Experiments were made on laser excitation separation refining, CVD, laser ablation, super-high vacuum, etc. For the stabilized formation of high-adhesion thin/thick films, studies were carried out of the surface activation for processing substrate surface before film formation, interface counter diffusion in thin film formation process, and the technology for combination of these. The higher-order structure control of materials was attempted using the reaction field combined with the photochemical reaction by the high grade photon field, based on the molecular beam vapor-deposition technology under super-high vacuum. In the synthesis of materials by the photon combined reaction field, studies were made of the design/process of a dynamic device which reacts like pulse the photon/high pressure/strong magnetic field on carbonaceous materials and a static combined reaction field device by the stationary high pressure field. A study was commenced of a synthesis method in relation to fullerene with a new structure which has unique characteristics. (NEDO)

FY 2000 report on the results of the R and D of fundamental technologies of superconductivity applications. Development of technology to process low consumption power ultra high speed signals; 2000 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

In relation to the project on the R and D of fundamental technologies of superconductivity applications, the FY 2000 results of the design/fabrication of superconducting circuits were summarized. As to the development of technology to design superconducting circuits, an increase in circuit scale was tried targeting AD converter use modulator and decimation filter. As a result, operation was confirmed in element circuits of flux quantum multiplier circuit, feed back driver, DC isolator, etc. Concerning the development of technology for standard junction and integration, RHEED observations on the thin film surface before/after etching and YBa{sub 2}Cu{sub 3}O{sub 7-x} re-deposition were tried to be made, and the potentiality as monitoring technology was indicated. With respect to the fabrication of small scale circuits for demonstration, the design/trial fabrication were made of the basic pattern of SFQ circuit elements such as DC-SFQ, T-FF and SQUID for inductance rating. In regard to the development of technology to measure characteristics of superconducting circuits, a system was fabricated for processing and measuring output signals from {sigma}-{delta} modulators by semiconductor circuits, and it made the evaluation of AD converter performance possible. (NEDO)

FY 1996 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Ti-Ni micro particle composite thick films could be synthesized using pulse evaporation type/magnetic field closed type evaporation source for both high hardness and high toughness. Corrosion resistant gradient composition thick films were obtained which change in composition from Ni to CrSi2 by on-substrate collision/serial sintering technology by micro particles produced by hybrid-plasma. The following were conducted: synthesis of micro particles by laser induction vapor phase reaction, formation of collision of airsol particles, and development of the continuous creation process of nano structure advanced materials by continuous combination of microwave sintering. As the higher-order structure control technology in the molecular beam complex reaction field, studies were made of photochemical reaction, effects of magnetic field on other-molecular reaction, and functional control technology. The molecular/higher-order structure control by photochemical reaction was an important factor for sensor function improvement of the formed thin film. Photon/pressure complex reaction field device was developed and an experiment was made on the material synthesis. The diamond/cBN solid solution synthesis, etc. were conducted and the hardness next to diamond was obtained. (NEDO)

Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of technologies to manufacture ultra-high efficiency crystalline compound solar cells; 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu kessho kagobutsu taiyo denchi no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on laminated cells comprising of GaInP/GaAs//GaInAs using poly-element compound semiconductors. This paper summarizes the achievements in fiscal 1999. In developing the technology to manufacture large-area ultra-high efficiency cells, fabrication of 5-cm square GaAs cells was worked on, and a conversion efficiency of 24.7%, which is equivalent or better than that for 1-cm square cell, was achieved by using the epitaxial growth temperature for the GaAs cell structure of 600 degrees C, by adopting the p-on-p structure and by making the electrode thicker by using the plating method. Furthermore, trial fabrication was performed on 5-cm square cells also on GaInAs as the bottom cell. A conversion efficiency of 4.6% was obtained in a 5-cm square cell as a result of high level homogenization of film thickness and composition by optimizing the gas flow in growing GaInAs onto an InP substrate, and using a growth temperature of 550 degrees C. In developing the technology to form GaInP/GaAs laminated cells, discussions were given by using 5-mm square cells on especially improving the GaInP crystallinity and reducing the series resistance in the window layer. GaInP/GaAs-2 bonded lamination cells were fabricated, whereas a conversion efficiency of 19.63% was obtained without using a reflection preventing film. (NEDO)

FY 1999 report on the results of the technology development of super metal. Development of technology of high corrosion resistant iron-base fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing iron/steel materials which enable remarkable improvement of maintenance loads and longevity of oil field developmental materials, study was conducted for remarkable improvement of strength and corrosion resistance by making crystal grain of iron/steel materials micro-fine to the limit, and the FY 1999 results were summed up. The study was conducted on the technology of fine structure formation using strong magnetic field and technology to predict material quality of micro structure using computational science. As a result, it was found that the fine grain even in size can be obtained by a combination of magnetic field orientation and recrystallization. By this, an image was constructed of the industrialization process of fine grained steel production which was combined with warm rolling process and applied strong magnetic field. Using the method to homogenize the finite element method, the basement was established for the method to evaluate an effect of the second phase on mechanical characteristics of fine multi-phase structure steel. The cementite single-phase film which is an important structural phase of carbon steel was successfully formed, and the Young's modulus and Poison ratio were determined as basic data for material design. (NEDO)

Fiscal 1999 report on results of R and D of industrial science and technology that creates new industry. Development of super metal technology (development of technology for innovative metallic material); 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of obtaining higher strength/toughness and higher anticorrosion in metallic materials, R and D was conducted on technologies for grain refining/dispersing and for amorphous bulk formed bodies, with fiscal 1999 results compiled. In the technological study on grain refinement and dispersion, austenitic stainless steel and 12Cr ferrite steel were used, with creative manufacturing carried out for microcrystallized structure materials by a powder metallurgy method. The result of the study revealed that suppressing grain growth by carbide or oxide was important for grain refinement, and that homogenizing the inside of a material by hot forging after solidification forming was essential for ductility improvement. In the development of the technology for amorphous bulk formed bodies, a laser heating type forming test device was designed and manufactured, with a technique examined in which bulk amorphous of a complex-shaped article was formed through rapid quenching of amorphous alloy powder by laser. This year, a trial production was performed for the laminated solidified bodies of Ni amorphous alloy powder, and the basic data was thereby collected such as feeding of the powder and conditions of the laser irradiation. (NEDO)

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

Fiscal 1998 R and D project on global environmental industrial technology. R and D result report on environment- friendly production technology (advanced chemical synthesis reactor); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bio reactor) kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For high-efficiency production of substances by bioreactor, study was made on a bio-control mechanism as its elementary technology. On the study of breeding technology by expression control, the structure design of a control region and development of new expression vectors had been finished, and study was made on breeding of high-efficiency recombinant production cells by using candidate expression vectors. On the study of breeding technology by multi-stage enzyme reaction control, the enzyme gene of a system synthesizing cysteine from glycerol was searched, and hydroxypyruvaldehyde hydrogenase gene was isolated as substance production model. Cysteine production Escherichia coli combined with serineacetyl transferase gene was also prepared. In addition, study started on cloning of hydroxyacetone oxidase gene. On development of reactor system technology, for conversion of serine to cysteine, study was made on optimization of a reaction condition by theory of enzyme reaction rate. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 1/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 1/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study RUN-5, the operation was carried out by using the Tanito Harum coal of Indonesia, and raising the slurry concentration to 50% by weight. The operation stability when the high concentration slurry was used was verified, and the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired by using the NAT method. In the RUN-6 and 7, for the purpose of verifying the applicability of the NEDOL process to the wide range of coal types as the process feature, the Adaro coal of Indonesia and the Ikejima coal of Japan were used, and the operation at high slurry concentration was performed at 80% load and under the standard NEDOL conditions. The operation stability when the upper and lower limit coals was used was verified, and the operability at high slurry concentration was identified. At the same time, the liquefying reaction column fluidity property data, and the material balance and heat balance data were acquired. The development targets established by the Industrial Technology Council have all been achieved. (NEDO)

FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper described the FY 1993 results of the technology to create high efficiency power generation use members. A processing method was proposed in which to manifest magnetic characteristics up to the theoretical value level, crystallization of magnetic alloy amorphous was controlled and size/configuration of precipitated micro-fine crystals are made ideal. For the development of environmental purification use high functional catalysts, experiments were conducted on the heightening of purity of materials. Namely, by the two wavelength two stage excitation method using color laser, atomic beams of the material metal emitted by electronic beam evaporating source are photo-excited up near the ionization level. These are separated from the non-ionized components by electrostatic field application, and only the ionized atoms are vapor-deposited on substrate. The separation accuracy was good. Plasma excitation of raw gas was done independently for every component, and the multi-source excitation plasma CVD was proposed which is film-formed on the substrate of which the periphery was separately controlled. The synthesis method was considered of higher-order structure control high functional organic materials which are composed of electrode reaction/high grade photon/extreme magnetic field. Study was made of complex reaction field application film-forming/molecular orientation technology using a small test device. (NEDO)

Explanative report on the achievements in research and development of a coal gasification technology in fiscal 1981. Research and development of a low-calorie gasification power generation technology; 1981 nendo sekitan gas ka gijutsu no kenkyu kaihatsu seika setsumeisho. Teikarori gas ka hatsuden gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the development works on a low-calorie gasification power generation technology in research and development of a coal gasification technology in fiscal 1981. The third sub-committee was established in the Coal Gasification Committee, and the sub-committee has summarized a survey report on coal gasification composite power generation upon having held seven discussion meetings. Surveys were carried out on the fluidized bed gasification process and the coal gasification composite power generation systems mainly in Germany and the U.S.A. where development of coal gasification technologies has been advanced. Germany and Britain who use great amount of coal are urged to find ways for how to clear the environmental criteria applied in the EC countries. The U.S.A. is moving forward the development of coal gasification technologies for power generation, chemical materials, and industrial fuel to be used as the substitutes to petroleum. This paper describes the development works at the Electric Power Development Company to realize a coal gasification composite power generation system of 1,000 t/d class. The pressurized fluidized bed system is assumed, and a verification test is scheduled to be performed on the chemical reaction characteristics by using a 40-t/d furnace. The furnace shape will be decided upon executing high-pressure cold model experiments. Fiscal 1981 has fabricated and installed devices for the high-pressure coal feeding system. Operation tests, air tightness tests, and instrumentation tests have verified normal operation. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of tanker for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso yuso tanker no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the tanker for liquid hydrogen transport was studied. In fiscal 1996, some experiments and numerical analyses were proposed which are necessary to solve technological issues extracted in fiscal 1995 for heat insulation structure. The issue was roughly classified into vacuum and non-vacuum insulation, and their basic functions and required performance were arranged. Boil-off rate of 0.2-0.4%/d was targeted. The insulation system which applies polyurethane form (PUF) to tank surfaces and injects atmospheric N2 gas into the surrounding hold space, could achieve the targeted insulation performance by PUF of 1m in thickness. The system of vacuum panel insulation and atmospheric N2 gas injection into a hold space required the panel of 500mm in thickness because of the large effect of metallic outer panel material. The system of vacuum hold and PUF panels was faced with the essential issue for realizing and maintaining vacuum hold. The super insulation system featured by layered insulation materials and vacuum layer spaces was also strongly affected by degree of vacuum. 23 figs., 8 tabs.

FY 1998 R and D of utilization of biological resources such as those in bioconsortia. Report on development results of techniques for utilization/production of organisms in bioconsortia; 1998 nendo fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to analyze functions and interactions of organisms having specific functions, to develop the techniques for isolating and cultivating the constituent organisms, and thereby to develop the techniques for their industrial utilization, in order to develop the techniques for handling organisms in bioconsortia as the techniques to utilize their functions, e.g., production and decomposition of materials, and also to develop the techniques for culturing/controlling microorganisms in bioconsortia and for strengthening their functions. The FY 1998 themes are development of the functional material production technology, and comprehensive study for the project. More concretely, the former includes histochemical analytical technology (development of techniques for detecting microorganisms in soil, and of techniques for in-situ detection/isolation of specific microorganisms in bioconsortia and for analysis their functions), isolation and culture technology (development of detection, separation and cultivation technology of microorganisms that are not easily cultured), functional substance production technology (technical utilization of microbial consortia for production of environment-friendly oil/water separation polymers), and functional material production technology (development of methods for artificial gene exchange in microbial consortia). (NEDO)

Report on achievements in fiscal 1999. Development of technology to utilize biological resources such as composite organism systems (development of technology to utilize and produce composite organism systems); 1999 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

It is intended to achieve the following objectives in terms of the technologies to utilize such functions as material production and material decomposition by using composite organism systems: develop a technology to handle the composite organism systems; establish a composite microorganism cultivation control technology, and a composite microorganism system function strengthening technology; develop a technology to separate and cultivate organism groups constituting them, and develop industrial utilization technologies. The fiscal 1999 has discussed developing the elementary technologies for the technology to utilize functions of the composite organism systems on the following research items: 1. a functional material production technology; and 2. comprehensive investigations and researches. In Item 1, development was made on a technology to detect, separate and cultivate microorganisms in soil as the histochemical analytical technology. Development was made on an in situ detection, separation and function analyzing technology for particular composite microorganisms as the function analyzing technology. In the separation and cultivation technology, development was made on a technology to detect, separate and cultivate difficult-to-cultivate microorganisms. In the functional material production technology, development was made on a technology to utilize microbial consortia producing environmentally harmonizing oil-water separating polymers, and a method to execute artificially the gene exchange in the microbial consortia. (NEDO)

Achievement report on developing coal liquefaction technologies in fiscal 1998 - edition B. Development of bituminous coal liquefaction technology (studies by using pilot plant) 2/2; 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho B. 2/2. Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to improve the environment by substituting petroleum energy by coal, and by reducing emission of SOx and NOx, research and development has been performed on coal liquefaction technologies. This paper summarizes the achievements thereof in fiscal 1998. In the operation study, the coal charging operation has been carried out for 269 days (6,169 hours) in total since the operation has been launched, and the targets were achieved. In the facility repairs, periodical inspections were performed including daily maintenance during the operation, the legal inspection on the boiler and the pressure vessel of the category one after completing the RUN-5, and disassembling and opening inspections on other devices. After having completed the RUN-6 and 7, the final verification inspection and the facility rinsing were performed after the operation studies have been completed. The data acquired in the facility maintenance were summarized as part of the technological package after the assessment. The investigative researches have executed development of a liquefying reaction simulator, tests and investigations on pulverization of the liquefying catalyst, evaluation on the activity of the used hydrogenating catalyst, and investigation on the effect of the coal liquefaction facilities and products on the environment. The technologies were investigated on coal liquefaction, and the plans for disassembling studies were established. (NEDO)

FY 1992 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The paper described the FY 1992 results of the technology to create high efficiency power generation use members. To enhance characteristics of super-high property permanent magnet up to the theoretical level, the development was proposed of a technology to control the size/configuration of micro crystal phase in association with the crystallization of alloy amorphous. For the development of environmental purification use high functional catalysts, a refining method using laser excitation was studied. The observation was also made of molecular adsorption on the Pd thin film catalyst prepared by RF sputtering. The multi-source excitation plasma CVD was proposed which was film-formed by exciting plasma as raw gas independently for each component and supplying it to the substrate of which the periphery was separately controlled. The paper also described the development of technology for ion/light combined assist ultra-thin film production for development of gas turbine combustion sensor. The study was also made of the synthesis of higher-order structure controlled high functional organic materials using the electrode interface combined field which is composed of electrode reaction/high grade photon/extreme magnetic field. In the development of the higher-order structure control technology using the photon combined reaction field, studies were made of the photo reaction film formation technology, the basic film formation technology in the combined reaction field, and the molecular orientation technology. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of storage facility for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the storage facility for a large amount of liquid hydrogen (LH) was studied. Gasification loss caused by heat input of LH delivery pumps was studied for liquefaction and power generation bases assuming an pump efficiency of 70%, and the total heat and mass balance such as interface conditions for calculating the amount of boil-off gas was reviewed. The target storage capacity of 50,000m{sup 3} was reasonable, however, the performance of loading arms should be examined. The capacity around 5,000m{sup 3} of coastal localized bases was reasonable for control delivery loss caused by coastal tanker or LH container system to 2.6%. The capacity of 500m{sup 3} was suitable for inland bases, resulting in the loss of 1.2%. The concept design of the storage tank of 50,000m{sup 3} extracted confirmation of low-temperature characteristics of adiabatic materials and structures, and development of leakage inspection technology and vacuum holding technology as issues. The concept design of the underground storage tank showed that the material specifications for LNG ones are applicable to it by using proper adiabatic structures. 4 refs., 72 figs., 27 tabs.

Achievement report for fiscal 1998 on the research and development of a basic technology to apply superconduction. Development of a low power consuming and high-speed signal processing technology; 1998 nendo chodendo oyo kiban gijutsu kenkyu kaihatsu seika hokokusho. Teishohi denryoku chokosoku shingo shori gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The development of a superconduction circuit designing and manufacturing technology has achieved the following results: with respect to designing a circuit for single flux quantum (SFQ), the 'high-speed high-accuracy AC converter for front end of software radio' was selected as the target for a prototype to demonstrate the performance of the SFQ circuit. In analyzing movements of different SFQ basic circuits, such circuit simulator software versions were introduced as Saber, WR-SPICE, Wins, and Microcap, different motion waveforms for basic theoretical circuits were derived to compare their performances, and the effectiveness was verified respectively. In trial fabrication of a small demonstration circuit, design parameters were acquired from SQUID. In developing the technology to measure superconduction circuit characteristics, the following results were obtained: with regard to the element measuring and evaluating technology, an in-plane distribution measuring device was started up; and with respect to the circuit characteristics measuring and evaluating technology, a measuring system with low noise and low magnetic field was introduced. Regarding the circuit high-speed characteristics evaluating technology, development was made on a micro-strip line and coplanar transmission route converter. (NEDO)

Report on the achievements in development of a coal liquefaction technology (a solvent extraction and liquefaction technology) in the Sunshine Project in fiscal 1981. Data 1. Development of a brown coal based solvent extraction plant (50 t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 1). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the data-1 for developing a brown coal based solvent extraction plant in the Sunshine Project in fiscal 1981. The data are for the development of a liquefaction plant for Victoria brown coal produced in Australia (a 50-t/d pilot plant). Fiscal 1981 has performed detailed design on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the machines and devices was procured, and the site construction was begun. Detailed design documents and drawings were prepared. The data collected in relation with the plant design included the followings: device lists, entire factory layout drawings, device arrangement drawings, process flow sheets, utility flow sheets (fuel gas and fuel oil systems, steam and condensate systems, air for instrumentation, plant air, cooling water supply and return, industrial water and treated water, a waste water treatment system, a nitrogen system, and a waste gas system), public pollution preventing facilities, hazardous location classifying plans, and material balances. The data collected in relation with the machine design included pressure vessel engineering specifications, heat exchanger engineering specifications, and device purchase specifications. (NEDO)

FY 1998 report on the results of the research and development of fundamental technologies for superconductor applications; 1998 nendo chodendo oyo kiban gijutsu kenkyukaihatsu seika hokokusho. Chodendo oyo kiban gijutsu keknyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

As to the research on the superconductor manifestation mechanism, Y123 monocrystal which was partially replaced with Zn and Ni was manufactured, and it was made clear that the addition of these impurities greatly change anisotropy of superconductors. It was made clear that instability of lattice and magnetism is included in high temperature superconductor. Also made clear was an important role in the Nb/Ba replacement in existence of magnetic flux melting phase transfer and the magnetic field induced pinning effect. The manufacture of Y123 bicrystal membrane was successful by the liquid phase epitaxy method. The manufacture of non-copper base K-Bi-O new superconductor was successful by the ultra-high pressure synthesis method. The stabilized process was established for large size crystals of 15-20mm square in Y base and of 20-25mm square in Nd base. Also successful was the growth by LPE method of crystal with thick membrane of 20mm x 20mm x 10{mu}m on the MgO monocrystal substrate. The non-bicrystalization of Y base Nd base monocrystal was successful, and the peak phenomenon control in Jc-H was found out. By neutron irradiation, the acquisition magnetic field of 3.7T at 77K was achieved using bulk Y base 123 material with diameter of 3cm. And, the critical current density of 60,000 A/cm{sup 2} was achieved at 77K and 3T. (NEDO)

FY 1998 annual summary report on photon measuring/processing techniques. Development of the techniques for high-efficiency production processes; 1998 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to develop the techniques for energy-efficient laser-aided processing; techniques for high-precision, real-time measurement to improve quality control for production processes and increase their efficiency; and the techniques for generating/controlling photon of high efficiency and quality as the laser beam sources therefor, in order to promote energy saving at and improve efficiency of production processes consuming large quantities of energy, e.g., welding, joining, surface treatment and production of fine particles. The R and D themes are microscopic processing technology: simulation technology for laser welding phenomena; microscopic processing technology: synthesis of technology for quantum dot functional structures; in-situ status measuring technology: fine particle elements and size measurement technology; high-power all-solid-state laser technology: efficient rod type LD-pumping laser modules and pumping chamber of a slab-type laser; tightly-focusing all-solid-state laser technology: improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology and fabrication technology for nonlinear crystal; and comprehensive investigation of photonics engineering: high-efficiency harmonic generation technology. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program. Practical application technologies for photovoltaic power systems (Development of peripheral technologies); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu seika hokokusho. Shuhen gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

As for their outputs, the 3kW separately-excited and self-excited photovoltaic power plants yield daily averages of 7.8kWh and 6.9kWh, respectively, and this means that the self-excited type is inferior to the separately-excited type in terms of conversion efficiency. Automatic measuring devices for photovoltaic characteristics are installed at Sapporo, Sendai, Nagoya, and Miyazaki, which will elucidate regional difference in photovoltaic characteristics. A simulation of photovoltaic characteristics is performed and the resultant value is compared with the yield of an experimental 3kW system, and the result of the comparison is found reasonable. Cell arrays are subjected to investigation for configurations lowest in output loss for the respective shadow patterns. Harmonic characteristics are analyzed under plural-interconnection circumstances. Studies are made to miniaturize and simplify system constituents, and it is found that a 3-hour storage is proper for a 3kW-class storage battery. It is also found that a self-excited type suffers less voltage fluctuation in interconnected operation on a small short-circuit capacity system. Possibilities are that independent operation is started when output is larger than load, which is to be detected by checking changes in phase, frequency, etc. Array configuration, arresters, and shielding wires are taken up for the study of measures to cope with direct thunder strokes. (NEDO)

FY 1998 annual summary report on photon measuring/processing techniques. Development of highly functional maintenance techniques for power generating facilities; 1998 nendo foton keisoku kako gijutsu. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The objectives are set to develop the techniques for non-destructive measurement of conditions of facility portions, especially those exposed to severe environments, e.g., elevated temperature and pressure, over a wide range; the techniques for measurement of leakage of, e.g., gases, at high sensitivity; the techniques of laser-aided welding and surface-modification treatment for the members exposed to severe conditions; and the techniques for generating photon beams of high quality and energy density as the tools therefor, in order to improve reliability and maintenance efficiency of power generating facilities. The R and D themes are microscopic processing technology: fabrication technology for functional micro-composite circuits; in-situ status measuring technology: gas concentration/component measurement technology, and photon wavefront compensation device technology; non-destructive composition measuring technology: high-sensitivity detection technology using short-wavelength photons; high-power all-solid-state laser technology: rod-type laser and slab-type laser; tightly-focusing all-solid-state laser technology: high-energy pulse, high-quality laser; and comprehensive investigation of photonics engineering: investigation for photon-applied measurement technologies. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

Survey on chemical engineering technologies for the global environmental protection; Chikyu kankyo hozen no tame no kagaku kogakuteki taisaku gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

The present paper suggests chief measures to suppress and reduce global greenhouse gases. Under the control of artificial environments such as bioreactor, hydroponics and vegetable factory, a very high fixing rate of CO2 can be obtained, but CO2 generation accompanying electric power consumption is also large. It is preferable to use methane as resource by reforming reactions or selective oxidative reaction. In the recovery technique of fluorocarbon, 100% recovery is desirable. Techniques for decomposing recovered fluorocarbon and converting it to harmless material are the most backward ones. Understanding of essential structural relationship of coal is necessary for establishing combustion technique for the reduction of N2O. The integrated power generation system composed from solid electrolyte type fuel cell and coal-gasifying process, high-performance, superheat pump system form scientific technology imposing no burden on the global environment. Establishment of purification technique for industrial- or living-related drain inflowing to a closed water area system, establishment and reinforcement of inspection system for oil spill in the oceans in a global scale are required. 240 refs., 63 figs., 30 tabs.

Fiscal 1999 technical survey report. Survey of energy conservation technologies in Japan; 1999 nendo kokunai no sho energy gijutsu ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

NEDO (New Energy and Industrial Technology Development Organization), in its effort to implement a joint project with importing countries, endeavors to popularize energy conservation technologies by introducing them into plants in the importing countries and by demonstrating their validity on real systems. Energy conservation technologies in use in Japan's steelmaking, cement making, chemical, and oil refining industries were reassessed in view of their usefulness in the above-said project. During the reassessment, they were analyzed also for cost effectiveness for the scales on which they would possibly be introduced. Ninety-four technologies were reassessed, which involved the top pressure recovery facilities, continuous casting facilities, high frequency melting furnace, and high efficiency sintering furnace ignition device, these for the steelmaking industry; the materials crushing vertical roller mill, NSP (new suspension preheater) type cement calcination kiln, finishing process preliminary crusher, urban wastes conversion into materials for cement making or into fuel, these for the cement making industry; the multi-effect evaporator for an ammonia manufacturing process and the device for collecting waste heat at the outlet of a synthetic gas compressor, these for the chemical industry; and reduction in the amount of injection steam by use of vacuum distillation tower top steam recycling, etc., these in relation with oil refining facilities. (NEDO)

Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Fiscal 1996 report on technological results. R and D on micromachine technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are (1) research on micromachine systems, (2) a subminiature liquid synthesizing system, and (3) comprehensive investigation and research. In (1), the researches were carried out on the miniaturization and functional combination of a micro laser catheter and a micro tactile sensor catheter, which are the primary components of a coeliac diagnostic and therapeutic system, a 'micro catheter for cerebral blood vessel/treatment', as a micromachine system in the medical field. In (2), R and D was conducted on a system element technology assuming it contributed to a subminiature liquid synthesizing system capable of preparing various liquids including pharmaceuticals accurately with a trace amount. In (3), examination was made on the application area of a micromachine system with priority given to a medical field and also on technological subjects to be tapped, as well as on the contents of (2), with a device installed for evaluating the operating characteristic of a distribution type fluid actuator as needed for the development. (NEDO)

Fiscal 1997 report on technological results. R and D on micromachine technology; 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches on basic element technology of micromachines are conducted that operate autonomously in a narrow small part in a complicated apparatus or in vivo. The areas of activity are 1. research on micromachine systems and 2. comprehensive investigation and research. In 1, (1) a micro catheter and (2) a micro tactile sensor catheter were studied while, in 2, basic technology and technological problems, particularly those problems concerning sophistication in the medical field were examined and studied. Further, in (1), with the purpose of developing a micro laser catheter for diagnosis/treatment, researches were implemented on the technology of integrating micro laser and an optical fiber which were components of the catheter and on the fabrication of the fine diameter of a micro catheter as well as on the characteristical improvement of the base body on which minute elements were mounted. In (2), characteristical improvement and sophistication were carried out for a high sensitivity contact pressure sensor and a diagnostic tactile sensor, which are mounted on a catheter having a positive bulge control mechanism for insertion into body cavity, with a sensor probe manufactured experimentally. (NEDO)

Report on the fiscal 1996 development of high efficient waste power generation technology; 1996 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The technical development was made by which high-temperature/high-pressure steam is generated in the incineration furnace using general waste, combustible industrial waste, etc. as fuel to generate power high efficiently, and reliability of the superheater, etc. was verified by the pilot plant. For it, the following were conducted: development of element technology (high-temperature/high-efficiency combustion furnace, corrosion resistant super heater materials, environmental load reduction technology) and the demonstration (demonstrative test in pilot plant, study of an optimum total system). In relation to the external circulation type fluidized bed furnace, reformation was made which enables simultaneous sampling of dioxins, etc. The combustion test was done using the reformed combustion testing furnace to obtain the data necessary for the study of formation/decomposition mechanism of dioxin. The amount of corrosion reduction of superheater sample material for pilot plant use was determined. A study was made of improvement of removal of dioxins and NOx in the pulse plasma exhaust gas treatment method. The pilot plant was installed. 10 refs., 205 figs., 79 tabs.

Development of technology for fuel alcohol. ; Searching and breeding of superior bacteria. Nenryoyo alcohol gijutsu kaihatsu. ; Yushukin no kensakuter dot ikushu

Energy Technology Data Exchange (ETDEWEB)

1990-10-01

In order to develop superior ethanol fermenting bacteria which would directly transform fibers into ethanol, which would lead to the utilization of unused waste industrial agricultural and forestry products, separation of potential strains from extensive collections of microbe resources from in and out of this country and adding of salt resistance, alcohol resistance, cellulose digestion properties using bio-technology were conducted. In searching for superior bacteria, some cells used in the sugar test plant showed no decrease in fermentation yields in 0.4% CaCl{sub 2}, 0.25 MgCl{sub 2} cultures, and some showed no decrease even with 1% KCl. In the breeding of superior bacteria, zymomonus with 4 times CMCase (a component enzyme of a cellulose degrading enzyme) activity, zymomonus which could grow in maltose cultures, zymomonus which had xylose isomerase genes linked to pyruvate carboxylase promoters, zymomonus resistant to 7% ethanol and 1% KCl, thermophilic and anaerobic cellulose degrading bacteria were developed. 1 tab.

Achievement report for fiscal 1998. Development of next-generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches are conducted on the development of a technology of catalytic cracking of naphtha, technology relative to selective oxidation reaction of saturated hydrocarbons, process technology utilizing solid-phase reaction field, and a process technology utilizing novel reaction mechanism. Also, a survey is conducted on chemical processes of the next generation. Concerning the catalytic cracking of naphtha, reaction systems are roughly divided into two groups by whether or not they proceed in the presence of oxygen. As for rare earth oxide catalyst systems and zeolitic catalyst systems, their performance is confirmed and their reaction mechanisms are estimated. Concerning the selective oxidation reaction of hydrocarbons, studies are made to enhance the performance of catalytic systems that have been selected in researches conducted in the past. Concerning the process of solid phase reaction field utilization, the project is summarized and a concept is constructed of 'solid phase catalyst.' Concerning novel reaction mechanism utilizing process technologies, development is discussed of a novel process using membrane reactor, a highly functional hydrogen permeable membrane, a low-temperature dehydrogenation catalyst, etc., and a dehydrogenation membrane reactor is experimentally built. (NEDO)

Data book on new energy technology development in FY 1997. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Various policies are being implemented in the field of new energy technology in line with progress in technological development. Examples are about assistance mechanism, field test projects and advisory projects to support the introduction of new energy technology. In order to promote the introduction of new energy efficiently, it is necessary to compile the various information regarding new energy in a comprehensive and systematic way, and formulate a basic data set. Among various new energy technologies, cogeneration is discussed in this report. The latest published data on the respective technologies are compiled particularly regarding their overall systems, examples of introduction, assistance mechanisms and state of implementation in foreign countries. Items included in this report are the trend of cogeneration, outline of system, state of introduction, forecast of introduction, overview of policies, basic terms, and related organizations. 9 figs.

Survey on problems in developing technologies for the global environment issues (Version II); Chikyu kankyo mondai gijutsu kaihatsu kadai chosa. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-07-01

This paper describes a survey on problems in developing technologies for the global environment issues. Technological development of means to reduce generation of environmental issues and substitutive means for non-generation thereof is being moved forward specifically in the Sunshine Project and the Moonlight Project. The Chemical Technology Research Institute assumes that it has a responsibility to positively contribute to developing a technological system that matches the substance circulation mechanism of the earth from the fields of chemistry. Therefore, the Institute has organized working groups that have been identifying problems from their expertise standpoints and have been extracting study assignments. Subsequent to the Version I, the Version II has been compiled. The Version II takes up the simulation of global warming mechanisms, behavior of gases dissolved in oceans, and possibility of fixing CO2 in oceans. With respect to fluorocarbons, the Version II describes development of substitutive substances, their stability, combustion method as a destruction technique, and destruction by means of super criticality. Regarding CO2, the version introduces technologies to re-use CO2 as a resource by means of membrane separation, storage, and contact hydrogenation. The volume also dwells on CO2 reduction by using photo-chemical and electrochemical reactions, CO2 reduction and photo-synthesis by using semiconductors as photo catalysts and electrodes. (NEDO)

Achievement report for fiscal 1998. Development of next-generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches are conducted on the development of a technology of catalytic cracking of naphtha, technology relative to selective oxidation reaction of saturated hydrocarbons, process technology utilizing solid-phase reaction field, and a process technology utilizing novel reaction mechanism. Also, a survey is conducted on chemical processes of the next generation. Concerning the catalytic cracking of naphtha, reaction systems are roughly divided into two groups by whether or not they proceed in the presence of oxygen. As for rare earth oxide catalyst systems and zeolitic catalyst systems, their performance is confirmed and their reaction mechanisms are estimated. Concerning the selective oxidation reaction of hydrocarbons, studies are made to enhance the performance of catalytic systems that have been selected in researches conducted in the past. Concerning the process of solid phase reaction field utilization, the project is summarized and a concept is constructed of 'solid phase catalyst.' Concerning novel reaction mechanism utilizing process technologies, development is discussed of a novel process using membrane reactor, a highly functional hydrogen permeable membrane, a low-temperature dehydrogenation catalyst, etc., and a dehydrogenation membrane reactor is experimentally built. (NEDO)

Fiscal 1982 Sunshine Project research report. Development of bore hole measurement technology; 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This report summarizes the fiscal 1982 research result on development of measuring instruments for information collection in geothermal bore holes under high-temperature high-pressure conditions. In development of high-temperature well logging cable, the new TFE Teflon insulated well logging cable (3,300m) applicable up to 320 degreesC was prepared. In development of digital well logging system, the data analyzer for edition and analysis of recorded digital logging data, the depth panel with an automatic depth correction mechanism, and the fiber optics controller were prepared. Preparation of the whole digital well logging system was thus completed. Field test was made at 3 wells in 2 geothermal areas. At the test well in Nigori-Gawa area, Hokkaido, performance test was made on the digital well logging system, TFE Teflon well logging cable, and improved winch completed in this fiscal year. At the same time, the radioactive well logging test using radioactive isotope showed the satisfactory result except neutron well logging. (NEDO)

Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on analysis of trends of technical innovation in Japan/Europe/the U.S.; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiso chosa (Nichibeio no gijutsu kakushin doko no bunseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For survey of the industrial competitive force, it is important to arrange the environment where the continuous and spontaneous technical innovation is generated. To recognize the present situation, the patent information relating to technical innovation, etc. were collected, indices of the number of patent, degree of the reference and scientific link in Japan, the U.S., and Europe were taken out by technology field to analyze the patent trend in the past 10 years. By technology field, the U.S. is superior in a lot of fields. Japan is at top rank in office supplies and camera fields, made strenuous efforts in automobile and semiconductor/electronic fields, but is behind others in medicine, biotechnology and aerospace fields. Concerning the number of patent registration in the U.S., Japan is superior to the U.S. in automobile/electric equipment/metal industries. Europe is superior in food and engineering fields. The U.S. is superior in aerospace industry and biotechnology fields. The U.S. is featured by a large number of patent applications by universities and government organizations. (NEDO)

FY 2000 report on the survey on the long-term energy technology strategy. Fundamental survey to work out industrial technology strategies (technology strategy by field - material technology field); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of constructing the material technology strategy, conducted were study of the trend of technical development, arrangement of material technology seeds, and survey of the R and D environment. Concretely, the paper carried out the grasp of the national projects related to materials in Europe and the U.S., patent registration (U.S.-Japan comparison)/application (Europe/Japan), transfer of technology trade, and survey of the trend of papers made public in scientific magazines. Further, in the survey of the R and D environment, conducted were how to treat researchers/engineers, how to handle intellectual ownership, system to promote the cooperation among industry/university/government, and comparison among countries in policies of technology such as patent strategy. The results of the survey were classified into the following 4 items: 1) trend of the technical development in the material technology field; 2) developmental environment in the material technology field; 3) competitive force in the material field and material user needs/seeds maps; 4) proposal for the material technology strategy. As to the competitive force of material technology in 3), the paper took up organic/polymer, iron/steel, aluminum, semiconductor, and ceramic materials. (NEDO)

FY 2000 Research and development project for creation of the standards. Standardization of information-providing technologies for establishing human/machine interfaces; 2000 nendo kijun sosei kenkyu kaihatsu jigyo seika hokokusho. Hito to kikai no interface kochiku no tame no joho teikyo gijutsu ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey/test/research project is aimed at standardization of providing information smoothly while securing safety for various types of drivers by introducing advanced technologies into vehicles.The methods of evaluating priorities of 105 items of information for drivers, which are taken up by ISO, are followed to find that 5.90, 2.05 and 0.11 items are selected for the alarm, route guiding and general information systems, respectively. These results are in agreement with the related literature survey results. The test results of the visual/auditory displays corresponding to the priority information types indicate that the adequate alarm displays are 'red/50nt/0.2 seconds, 30% frequency/6.0 degrees' for the visual sensation, and '80dB/2.0KHz+1.5 harmonics/0.2 seconds, 70% frequency' for the auditory sensation. The study on information volume and information recognizing time indicates that the symbol pattern is better than the letter pattern for the simultaneous display of up to 2 items learned beforehand. The others studied include alarm designs and management of two or more alarms. (NEDO)

Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a high-temperature bed drilling technology (Feasibility study on high-temperature bed drilling); 1980 nendo koon chiso kusaku gijutsu no kaihatsu seika hokokusho. Koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Discussions were given on feasibility of a technology to drill efficiently a high-temperature bed (350 degrees C and 400 kg/cm{sup 2}) to 3 to 5 km. This paper summarizes the bit items for development (bearings, cutters, blade tips, sealing materials, a tip retaining method and structures). The roller cutter bit had the retaining power of the mother cutter material strengthened by using improved carbonized steel and heat treatment. A bit bearing using heat resistant material showed a life of 40 hours or longer at 350 degrees C. The solid bit using a two-layered ultra hard blade tip achieved a drilling rate of 0.84 m/h without any breakage. Studies were also advanced on the air friction drilling method. This paper also dwelled on heat and corrosion resistant blade tips, materials, enhancement of heat resistance in powder sintered cutters, and studies on the bit sealing. In addition to discussions on the percussion drilling as a new drilling method, discussions were given on slanted drilling, air drilling and multi-leg drilling. The paper summarizes these discussions together with development problems to be solved in the future. Research and development works were carried out also on an explosion preventing device, a roll packer, and a rotating head prevent device. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

Achievement report for fiscal 1999 on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Survey and research on its social acceptability); 1999 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu - Shakai tekigo sei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to evaluate feasibility of practical use and economy of the coal hydrogasification technology (the ARCH process), survey and research have been performed. This paper summarizes the achievements in fiscal 1999. In the survey on the social acceptability, survey has been made on the future trend in the demand and supply and the price of LNG, LPG, and coal for hydrogasification. As a result, it was discovered that the price of LNG imported into Japan is determined as if linked with the crude oil price, and Saudi Arabia is the price leader of the LPG price. With respect to the survey on the possibility of international cooperation, surveys were conducted on the prospects of the long-term demand and supply in China, natural gas resources, and the demand and supply thereof. The feasibility study has estimated the product gas manufacturing cost after the process has been improved. In the trial calculation on the three-mode cost, it was discovered that, although the profit from byproducts is great, the BTX maximized mode causes the manufacturing cost to be higher by as much as 2 to 3 yen per Nm{sup 3} than that of other modes because of higher unit consumption in raw materials and higher construction cost. (NEDO)

Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development in its 3rd year (Research and development of process change accommodating flexible robot technology); 1999 nendo kotei tekiogata flexible robot gijutsu ni kansuru kenkyu kaihatsu seika hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A prototype force control piston insertion device which does not need jigs is built for use on the assembly line. An extensive reduction in investment for automated facilities is expected to realize because jigs conventionally required for each size are dispensed with. For expanding the scope of force control application, the device is verified for serviceability by use of a 5-axis robot and a visual servo control technique. A combination of vibration control and tracking control is applied to an integrated simulation/experiment environment. For the processing of inner force sensor data, a pseudo contact point monitoring technique is used. A wire type tactile sensor is proposed, which has a flexible-structure moment detector in which a flexible beam like a piano wire is the probe. For the inspection of ICs (integrated circuits), a passive compliance unit and a force control based flexible inserter are fabricated, to be used for a reduction in the number of no-good contacts. Technologies of shock absorption aided by robot terminal device tactile sense and of virtual damper control for shortening the setting time are verified for their validity by use of the IC inspecting inserter. (NEDO)

Research cooperation promoting project in fiscal 1998. Research cooperation related to developing mine resources extraction and treatment technologies of environment harmonizing and high efficiency type; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to realize more effective utilization of non-ferrous metal resources, joint research cooperation is made with the Republic of Kazakhstan. It is intended that valuable metals (gold, silver, copper, rare metals, and others) contained at large quantity in ore scraps generated in association with mine operation be extracted and recovered efficiently paying considerations to the environment. The treatment process consists of the following conception: raw materials such as ore scraps are leached by sulfuric acid and microorganisms to separate and recover gold and silver; the leach liquor containing valuable metals is extracted by using solvent and recovered of copper and rare metals via an electrolytic process; and the waste water is treated and discharged. Fiscal 1998 has performed studies on the wet treatment system at the site and in Japan, the gold and silver treatment, and the waste water treatment by using samples collected from the site in fiscal 1996. Based on the results of these fundamental studies, a pilot plant was built, and all of the facility fabrication was completed in fiscal 1998. Part of the facilities has been transported to the site. To drive the project forward effectively, materials and items of equipment required for the joint research were procured and transported to the country, and at the same time Kazakhstanian researchers were received in Japan for training. (NEDO)

FY 2000 Research and development project for creation of the standards. Standardization of information-providing technologies for establishing human/machine interfaces; 2000 nendo kijun sosei kenkyu kaihatsu jigyo seika hokokusho. Hito to kikai no interface kochiku no tame no joho teikyo gijutsu ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey/test/research project is aimed at standardization of providing information smoothly while securing safety for various types of drivers by introducing advanced technologies into vehicles.The methods of evaluating priorities of 105 items of information for drivers, which are taken up by ISO, are followed to find that 5.90, 2.05 and 0.11 items are selected for the alarm, route guiding and general information systems, respectively. These results are in agreement with the related literature survey results. The test results of the visual/auditory displays corresponding to the priority information types indicate that the adequate alarm displays are 'red/50nt/0.2 seconds, 30% frequency/6.0 degrees' for the visual sensation, and '80dB/2.0KHz+1.5 harmonics/0.2 seconds, 70% frequency' for the auditory sensation. The study on information volume and information recognizing time indicates that the symbol pattern is better than the letter pattern for the simultaneous display of up to 2 items learned beforehand. The others studied include alarm designs and management of two or more alarms. (NEDO)

Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

Evaluation report on the research and development of automatic sewing systems; 'Jido hosei system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

A comprehensive evaluation is made upon completion of the automatic sewing system research and development project. The project aims to achieve a 50% increase in productivity through effective use of a multiple-product/small-amount production scheme in small and medium sewing industries. The intelligent cloth inspecting machine (prior to sewing) in a laser-aided cutting system is as competent as the currently used sewing mill inspection system, and the resultant data are effectively utilized in the cutting process. As for the cutter, it is demonstrated that it is more than two times higher in cutting speed than a currently used laser cutting system; that it is sufficiently accurate in avoiding parts with flaws and in pattern matching; and that it is reliable in complying with process information provided. As for the flexible sewing system, it is acknowledged that it correctly recognizes information attached to cut parts and that it joins them with flexibility in response to changes in the material, pattern, or size. As for the high-technology assembling system, satisfaction is found in its automated 3-dimensional sewing of parts received from the previous stage and in its flow of production. As for the 3-dimensional flexible press, the quality after finish is found satisfying. The said systems are integratedly operated, and it is found that the goal of the research and development has been achieved. (NEDO)

Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

2000-10-25

The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

FY 2001 report on the results of the follow-up study of development of the highly effective waste power generation; 2001 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up gijutsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of safe operation of the highly effective waste power generation pilot plant, confirmation of the performance of corrosion resistant super heater materials under the high temperature corrosion environment, collection of the data on environmental load characteristics in waste incineration, etc., the follow-up study was made. The results were as follows: The pilot plant was able to generate high temperature/high pressure vapor stably for approximately 13,500 hours in FY 2000 and FY 2001 and for approximately 27,800 hours in 4 years since the start of the demonstrative test. The planned performance of plant facilities was fully satisfied, and the performance of environmental load reduction was fully satisfied in standard values of soot/dust, SOx, NOx, hydrogen chloride and dioxins in exhaust gas. Concerning the super heater use developmental material, its durability of 5 years or more was confirmed. It was forecast that by using this, the heightening of temperature/pressure of boiler to 500 degrees C and 100 atmospheric pressure was achieved. Further, the useful information/knowledge on plant design were obtained such as the corrosion prevention technology for waste plant and the forecast of corrosion life of materials. (NEDO)

Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Research on actualities of Japanese industries' research and development potential); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (Nippon kigyo no kenkyu kaihatsuryoku no jittai ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For working out propositions on what the country should do and on what improvement industries should make for the strengthening of industries' competitive power on the market, analyses were conducted into the objects of research and development, organizations engaged in research and development activities, methods of evaluation, and the like. In concrete terms, studies were made on industries' roles in research and development activities and on the actualities of basic research and development potential, and then a survey was conducted through questionnaires and interviews about (1) tasks relating to corporation management and research and development potential, (2) development of research dedicated talent and its fluidity, and (3) problems feared to get worse in the future. Questionnaires were sent to 217 corporations or 577 people of whom 37.6% responded. Each item is described below. Under item (1), it is pointed out that basic research has shrunk as a whole, that pressure is on the increase urging that research directly increase profit, and that theme selection is made to match the business model. Under item (2), it is stated that post-doctorate researchers' knowledge is respected but that recruitment is another matter, and that fluidity of researchers between corporations will increase. Under item (3), it is pointed out that researchers are increasingly inferior in quality and that brain drain out of Japan is feared. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

FY 1974 report on the results of the Sunshine Project. Comprehensive study of hydrogen use subsystem and study on the periphery technology (Study on the periphery technology of hydrogen); 1974 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-05-01

This is aimed at making an investigational study on the periphery technology and sprouting technology of the hydrogen energy system. In Volume 1, 'Technology of hydrogen production,' as to the hydrogen production, the paper summed up the expected technical subjects on the electrolysis method and thermochemical method. The paper further included the survey of the direct pyrolysis method and the hydrogen production method using solar energy. Concerning the latter, in Volume 2, the light electrode reaction was theoretically developed, and samples of various hybrid methods were concretely studied. In relation to subjects on hydrogen and materials, in Volume 3, the results were described of the investigation into the hydrogen behavior in metal which is the most basic field of the subjects. About the storage method which is important as periphery technology, the study was made of the methods which can be expected but liquefied hydrogen and metal hydride which are now under research and development. In the last volume, as a part of the work to review the hydrogen energy system from a wider viewpoint, the basic study was additionally made in comparison with the system using coal. (NEDO)

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

Fiscal 1997 report on the development of an energy use rationalization ultra-high tech liquid crystal technology. Project of development/promotion of ultra-high tech electronic technology / technology of design/control/analysis of new functional electronic materials; 1997 nendo kenkyu seika hokokusho energy shiyo gorika chosentan ekisho gijutsu kaihatsu. Chosentan denshi gijutsu kaihatsu sokushin jigyo / shinkino denshi zairyo sekkei seigyo bunseki gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

A research was conducted with the aim of developing an ultra-low power consuming type information display which supports the next next generation informatizing society. As to the function combined type fine structure formation technology, a formation technology of fine structure supporting multi-layer pixel by organic polymer materials was established to confirm a possibility of adopting it to high functional liquid crystal display. Concerning the high functional fine structure formation technology, a study was proceeded with on holographic PDLC which is an interference reflection coloring method. In relation to the low temperature film formation technology of ferroelectric thin films, a film formation device was introduced to obtain basic data, and at the same time a possibility was studied of improving film characteristics by laser annealing conducted after the film formation. Moreover, concerning the new functional material technology, studies were made of optical interference/high light-scattering control materials, light alignment elements, ultra-high purity/ultra-reliable optical materials, ultra-anisotropy optical materials, etc. About the light reflection characteristics control technology, studied were new liquid crystal molucular orientaion control technology, multi-dimensional anisotropy structure formation technology, etc. 100 refs., 273 figs., 58 tabs.

Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and dessolution deposition process); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu (yokai sekishutsuho))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to manufacture low-cost large-area solar cell modules, developmental research has been performed on a film manufacturing technology using the dessolution deposition process. This paper summarizes the achievements in fiscal 1999. The research has been performed on a technology to form a thin silicon film directly on carbon substrates being substrates of different kinds, without using seed crystals. The researches made up to the previous fiscal year has made possible to form the film onto a substrate of about 5-cm square, has fabricated cells although with a small area, and indicated the importance of reducing concentrations of impurities in the solvent metals used. The researches performed during the current fiscal year executed modifications to reduce the temperature distribution in the substrate surfaces, including size increase in the heater, and improvement in the cooling heat conduction mechanism. As a result, films were formed successfully on 7.5-cm square substrates. In reducing the process temperatures, it was made clear that films can be formed at lower than 700 degrees C by using zinc as a solvent metal. Furthermore, the purity enhancement in the solvent metal achieved a conversion efficiency of 11.6% although the area is as small as 3.73 cm{sup 2}. (NEDO)

FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-04-01

Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

FY 2000 Report on the results of research and development of the important regional technologies. Development of high-order processing of high-melting metal-based parts (Development of technologies for creating parts for high-efficiency power production); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Koyuten kinzokukei buzai no kodo kako gijutsu (kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of heat-resistant materials, aimed at increasing operating temperature of gas turbines not equipped with a cooling system and thereby further improving their thermal efficiency. The program for design/evaluation of high-strength, Nb-based solid solution alloys develops the Nb-based alloy reinforced with a solid solution comprising 5 to 30% of Mo and 5 to 15% of W, all by atom, simultaneously dissolved. The program for design/evaluation of high-strength, Nb-based composite materials confirms effectiveness of incorporating Si in a Nb alloy and separating silicide in the Nb-based solid solution alloy matrix as the combined mechanism of reinforcing the alloy. The program for creation/evaluation of Nb-based parts which withstand superhigh temperature finds that the discharge plasma method gives the structure, in a very short time, almost on a level with that given by the solution solidification method. The program for oxidation resistance improving technologies develops the electrochemical process for forming the oxidation-resistant coating film. The stable oxidation-resistant performance is observed in the preliminary test, because the sample loses no weight when exposed to around 1000 degrees C in air for 10 hours. (NEDO)

Report on 'manufacturing technology supported by advanced and integrated information system through international cooperation'. Domestic surveys; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kokunai chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The committee of manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC) has been established as the organization to promote necessary surveys, deliberate the research and development guidelines and themes, and thereby support the joint R and D projects with Asian countries to improve information systems for their manufacturing industries by MATIC. The R and D skeletons are set in FY 1994 for the works in and after FY 1995. The relationships between affiliates of Japanese enterprises and local enterprises, actual conditions of the manufacturing industries and so on are surveyed, in order to extract problems related to the information systems for the promising manufacturing industries in the Asian countries. Each industry has its own characteristics with respect to, e.g., numbers f parts and process steps, product life cycle, extent of automation, skill of workers, and spread of the related industries. Therefore, 3 industrial areas are picked up as those considered to be adequate for the case studies, and surveyed for the system functions, performance, elementary techniques and so on which are required to establish the information systems for their production systems. (NEDO)

Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of drilling technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen kussaku gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of developing deep geothermal resources, development of 'drilling technology of deep geothermal resources' was made from FY 1991 to FY 2001, and the results were summarized. As to the development of bits, the bit that can be used for 30 hours or more at a temperature of 250 degrees C was developed, and the demonstrative test was made in FY 1997. Relating to the development of the high temperature use drilling mud, the mud that can be used at a temperature of 350 degrees C was developed, and the test using the actual well was conducted in FY 1997. Concerning the development of the high temperature use cement slurry, the cement slurry with specific gravity of 1.35 or below that can be used under the environment of a temperature of 350 degrees C was developed, and the hanging test of the specimen was made in the actual well in FY 1998. About the development of the high temperature use downhole motor, a prototype of 1/12 scale was fabricated in FY 1998, and the performance test at high temperature was conducted. As to the development of the high temperature use high strength cement slurry, a cement slurry with specific gravity of 1.50 or below and compressive strength of 19.61 MPa that is used under the environment of a temperature of 300 degrees C was developed, and the test on the long-term compressive strength was made in FY 2001. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - R and D of evaluation technology of the photovoltaic power system. R and D of the solar cell evaluation system; 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyodenchi hyoka gijutsu no kenkyu kaihatsu - Taiyodenchi hyoka system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the development of the basic technology for the integrated evaluation of solar cell performance, grasp of degradation phenomena of solar cell modules by outdoor exposure test, development of the accelerated degradation test method, etc., and the FY 2000 results were summed up. As to the development of the ultra-high approximation solar simulator for cell evaluation, a simulator was fabricated of which the irradiation non-uniformity is {+-} 1.0% and the spectral agreement is within {+-} 10% in 10 wavebands out of the 16 wavebands. Relating to the development of evaluation technology of large area modules, performance of the spectral irradiance distribution, etc. was improved by modification of the solar simulator, which made accurate measurement possible. In the study of degradation of solar cell modules, exposure tests on various kinds of solar cell modules were continued at 5 sites in Japan, 3 sites in Australia and 1 site in Oman for data collection/analysis. Further, analysis was made of Isc changes in the early stage of exposure, phenomenon of cell's cloudy discoloration, degradation caused by increase in series resistance, etc. As the test method of light accelerated degradation of A-Si solar cell, a brightness cycle test method was developed. (NEDO)

FY 1999 research and development of technologies for creating original high-function materials. Development of technologies for functionalized materials for power generating facilities (Report on the R and D results of controlling precise structures of polycondesed systems); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu (shukugokei seimitsu kozo seigyo no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the polymerization catalysts and precise polymerization processes which can freely control the primary structures, e.g., molecular weight, regularity, branching and terminal group structures, of the polymers produced by polycondensation and ring-opening polymerization, in order to drastically improve their functions, and the FY 1999 results are reported. The basic studies on the precise polycondensation successfully lead to chemoselective synthesis of polymers by the direct polymerization, and synthesis of polyamides of narrow molecular weight distribution and high-molecular-weight aliphatic polyesters. The other items studied include precisely, regularly sequential polymerization by amine activation, innovative synthesis of polycarbonate, precise control of branching structures, regioselective oxidative coupling polymerization, and matrix polycondensation. The basic studies on the controlled ring-opening polymerization cover cationic ring-opening polymerization behavior of 6-membered thiocarbonate derivative having an ester group, to generalize the polymerization controlled by neighboring group participation. The other items studied include precise control of branching structures, molecular weights, network polymer structures, and polymer unit sequences. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

FY 1998 report on the project for development of hot water utilizing power generating plants and others, supported by New Sunshine Project. Development of extraction technologies and development of production technologies for the deep-seated geothermal resources; 1998 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of the activities for development of extraction and production technologies for the deep-seated geothermal resources, which are expected to contribute to increased geothermal power generation capacity. The program for the PTSD logging technology connects the S probe to PT probe, to simultaneously measure temperature, pressure and volumetric flow, producing the data of good quality even in a high temperature environment over 327 degrees C. Thus, possibility of the commercial system is confirmed. The D probe also produces a density calibration curve showing very good linearity, and operates normally in a high temperature environment of 406 degrees C. The program for the PTC monitoring technology conducts the field tests at Larderello, Italy, to confirm the sampler functions in a high temperature environment. The program for the tracer monitoring technology extracts promising tracers stable at high temperature from those for the liquid, vapor and liquid/vapor mixed phases. Silica is observed to be massively dissolved at 400 to 1,000mg/kg in the fluid under deep geothermal conditions. Scale precipitation rate is minimal for the first 21 days, but increases linearly with time thereafter. The experiments are also conducted for formation and prevention of the Fe-Si-based scales during the flushing period. (NEDO)