Sample records for kansoku ni yoru

  1. Estimation of underground structures in Kyoto city by seismic-array observations of microtremors; Bido no array kansoku ni yoru Kyoto shinai no chika kozo tansa

    Miyakoshi, K; Kagawa, T; Akazawa, T [Osaka Soil Test, Osaka (Japan); Ogawa, Y; Shimizu, K [Osaka Gas Corp., Osaka (Japan); Ejiri, J [Obayashi Corp., Tokyo (Japan)


    Observations of microtremors were carried out to estimate the S-wave velocity structure by using arrays of seismographs around the Kyoto Research Park. The observation points were so arranged that equilateral triangle arrays may be formed with maximum radii at 0.2 km, 0.4 km and 0.8 km respectively with the premises of the Kyoto Research Park as the center. The seismographs have used seven vertical movement components (PELS), and were adjusted to a period of eight seconds. In addition, high-cut filters of 4 Hz were used because the observation areas are located in urban areas with heavy traffic. The analysis has used the spatial self-correlation method as a means to estimate phase velocity of surface waves contained in microtremors. As a result, phase velocity estimation has become possible for frequencies from about 0.4 Hz to 2 Hz, whereas the S-wave velocity structure was estimated to a depth of down to about 900 m by using as reference the result of the reflection method exploration having been carried out in the present areas. In addition, it was suggested that microtremors with frequencies higher than 1 Hz are in unsteady state in terms of time or space. 4 refs., 7 figs., 1 tab.

  2. Hydrogenation of heteroaromatics by high pressure DTA techniques. 3; Koatsu DTA ho ni yoru hokozoku kagobutsu no suisoka (rutenium tanji shokubai ni yoru kakusuisoka datsu hetero hanno)

    Yamamoto, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Cooperation Agency, Tokyo (Japan)


    Ring-opening of heteroaromatics and heteroatom-removal reaction were studied experimentally using the acidic catalyst containing phosphoric acid for improvement of an upgrading method of coal derived oils. In experiment, some Ru-carrying metal oxide catalysts such as RMZ, RML and RMN catalyst, and MNP catalyst containing phosphoric acid were used as specimens. Nuclear hydrogenation reaction and hydro-denitrogenation reaction of dibenzothiophene and carbazole were compared with each other. The experimental results are as follows. Both RMN and RMNP catalysts offer a superior selectivity in nuclear hydrogenation reaction and hydro-denitrogenation reaction of carbazole. Although both catalysts offer an extremely high nuclear hydrogenation activity at 360{degree}C, these offer the high selectivity of denitrogenation products at 430{degree}C. In comparison of the activities of MN and MNP catalysts with the same Mn2O3:NiO ratio, MNP catalyst offers the higher denitrogenation activity than MN catalyst at 430{degree}C. 1 ref., 3 tabs.

  3. Estimation of shallow ground structure using short-period microtremors array observation. Results in Morioka area; Tanshuki bido no array kansoku ni yoru senbu chika kozo no suitei. Moriokashiiki ni okeru kekka

    Yamamoto, H; Obuchi, T; Saito, T; Iwamoto, K [Iwate University, Iwate (Japan). Faculty of Engineering; Yoshida, Y [OYO Corp., Tokyo (Japan)


    The velocity structure in the shallow ground structure was evaluated by observing microtremors of 1-10Hz in the Morioka City area. Plural wave sections free of vehicle noises or the like were selected out of the collected microtremor records, and the Fourier spectrum and coherence were calculated. Records sufficiently supporting the correlation between seismographs were chosen for the analysis. The phase velocity was calculated for each observation spot from plural array records by use of the F-K spectrum. The underground velocity structure was estimated by the inversion process using the matrix method. In this method, an early model was built on the basis of the observed phase velocity and the optimum underground velocity structure was determined by alternately performing two inversion processes: one for the case wherein the S-wave velocity is the sole parameter and the other for the case wherein the layer thickness is the sole parameter. As the result, a shallow underground velocity structure, which has good agreement with the available boring data in the Morioka City area, was successfully estimated, verifying the validity of this method. 4 refs., 7 figs.

  4. Estimation of subsurface structures in a Minami Noshiro 3D seismic survey region by seismic-array observations of microtremors; Minami Noshiro sanjigen jishin tansa kuikinai no hyoso kozo ni tsuite. Bido no array kansoku ni yoru suitei

    Okada, H; Ling, S; Ishikawa, K [Hokkaido University, Sapporo (Japan); Tsuburaya, Y; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center


    Japan National Oil Corporation Technology Research Center has carried out experiments on the three-dimensional seismic survey method which is regarded as an effective means for petroleum exploration. The experiments were conducted at the Minami Noshiro area in Akita Prefecture. Seismometer arrays were developed in radii of 30 to 300 m at seven points in the three-dimensional seismic exploration region to observe microtremors. The purpose is to estimate S-wave velocities from the ground surface to the foundation by using surface waves included in microtremors. Estimation of the surface bed structure is also included in the purpose since this is indispensable in seismic exploration using the reflection method. This paper reports results of the microtremor observations and the estimation on S-wave velocities (microtremor exploration). One or two kinds of arrays with different sizes composed of seven observation points per area were developed to observe microtremors independently. The important point in the result obtained in the present experiments is that a low velocity bed suggesting existence of faults was estimated. It will be necessary to repeat experiments and observations in the future to verify whether this microtremor exploration method has that much of exploration capability. For the time being, however, interest is addressed to considerations on comparison with the result of 3D experiments using the reflection method. 4 refs., 7 figs.

  5. Experiment for estimating phase velocity and power fraction of Love wave from three component microtremor array observation in Morioka area; Moriokashiiki deno bido no sanseibun array kansoku ni yoru love ha no iso sokudo oyobi power hi suitei no kokoromi

    Yamamoto, H; Yakuwa, A; Saito, T [Iwate University, Iwate (Japan). Faculty of Engineering


    Three component microtremor array observations were carried out in two locations in the city of Morioka for an attempt of estimating phase velocity and power fraction of Love wave by applying the expanded three component spatial self-correlation method. The microtremors were observed by using a seismograph with a natural period of one second. The arrays were so arranged as to form an equilateral triangle consisted of seven points. The maximum radii were 100 m, 50 m, 25 m and 12.5 m for vertical movements, and 100 m and 30 m for horizontal movements at the Iwate University, and 80 m, 40 m, 20 m and 10 m for vertical movements and 90 m for horizontal movements at the Morioka Technical Highschool. The analysis has used three sections, each with relatively steady state of about 40 seconds as selected from records of observations for about 30 minutes. The result of the discussions revealed that it is possible to derive phase velocity of not only Rayleigh waves but also Love waves by applying the expanded spatial self-correlation method to the observation record. Thus, estimation of underground structures with higher accuracy has become possible by using simultaneously the Rayleigh waves and Love waves. 3 refs., 11 figs., 2 tabs.

  6. Estimation of underground structures in the Osaka-Kobe area by array-network observations of microtremors; Bido no array kansoku ni yoru Osaka-Hyogo chiiki no chika kozo no suitei

    Okada, H; Ishikawa, K; Ling, S [Hokkaido University, Sapporo (Japan); Sasabe, K [Ministry of Construction, Tokyo (Japan)


    Microtremor observations have been carried out with an objective to estimate underground structures including the foundation depth in the Osaka-Kobe area which has been greatly damaged by the Hyogoken-nanbu earthquake in 1995. Different organizations have made seismic surveys and boring investigations in this area, by which elucidation has been made on the underground structures. The present observations are intended to identify S-wave velocity distribution in a wide area from the ground surface to the foundation, which is difficult to be verified by using conventional surveys and investigations. Methods to detect surface waves which are contained in microtremors include the frequency-wave number method (the F-K method) and the spatial autocorrelation method (the SPAC method). The SPAC method can estimate phase velocities of longer waves for the size of an array than with the F-K method, and is more advantageous in estimating ground structures at greater depths. S-wave velocity structure was estimated down to the foundation rocks existing in depths of about 0.5 to 2.0 km. For estimating the phase velocities in Raleigh waves, the SPAC method and the expanded spatial autocorrelation method were used. The underground structures thus derived showed a good agreement with the results of explorations using other methods. 8 figs., 1 tab.

  7. Investigation of aerodynamic stability by wind response observation during cantilever construction of the Ikara Ohashi bridge; Ikara Ohashi haridashi sekoji no kaze kansoku ni yoru taifu anteisei no kento

    Ueno, K.; Mukai, H.; Takeda, T. [Kajima Corp., Tokyo (Japan)


    In order to ensure aerodynamic stability during cantilever construction of the Ikara Ohashi Bridge, wind response observation was carried out and discussions were given on the result. The Ikara Ohashi Bridge is a 5-span continuous PC cable-stayed bridge with the central span being a concrete bridge having a length of 260 m, which is the longest in Japan. The bridge was constructed using a method that main girders are extended from the central tower to the right and left sides while the girders are stayed by bracing cables. The bridge construction site is in an area which is often subjected to typhoons and gusts like seasonal winds in winter, hence a discussion on aerodynamic stability of the bridge especially during extension work was viewed as an important matter. In addition, the construction used two small-capacity cables spaced and bundled as the bracing material, which required verification on their aerodynamic stability. In order to identify vibration characteristics of the main girders and the central tower, wind response observation has been performed as soon as the construction was begun. As a result, the vibration characteristics of the main girders and the central tower were identified, and it was verified that vibration shape and dominant frequency can be evaluated properly by an intrinsic value analysis that uses a multi-material point frame model. Furthermore, effects of different vibration absorbing measures were compared, and the effective methods were adopted as the result. 4 refs., 12 figs.

  8. Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

    Ishida, S; Suzuki, T; Yamamoto, M [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization


    This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

  9. System approach on solar hydrogen generation and the gas utilization; Taiyo energy ni yoru suiso no seisei oyobi sono riyo system ni kansuru kenkyu

    Fujii, I; Hirooka, N; Deguchi, Y; Narita, D [Meiji University, Tokyo (Japan)


    An apparatus is developed to establish a system which allows utilization of hydrogen safely and easily, and its applicability to a hydrogen system for domestic purposes is tested. The system converts solar energy by the photovoltaic cell unit into power, which is used to generate hydrogen by electrolysis of water at the hydrogen generator, stores hydrogen in a metal hydride , and sends stored hydrogen to the burner and fuel cell units. It is found that a hydrogen occluding alloy of LaNi4.8Al0.2 stores hydrogen to approximately 80% when cooled to 20 to 25degC, and releases it to 10% when heated to 40degC. The fuel cell uses a solid polymer as the electrolyte. The hydrogen gas burner is a catalytic combustion burner with a Pt catalyst carried by expanded Ni-Al alloy. The optimum distance between the burner and object to be heated is 22mm. High safety and fabrication simplicity are confirmed for use for domestic purposes. The system characteristics will be further investigated. 4 refs., 8 figs.

  10. Determination of standard Ghibbs free energy of formation of NiW sub 2 B sub 2 and activity of Ni-W binary system by EMF measurement. Kidenryokuho ni yoru NiW sub 2 B sub 2 no hyojun seisei Gibbs jiyu energy to Ni-W 2 seibunkei no katsuryo no sokutei

    Kayama, Koichiro; Hashimoto, Yasuhiko; Suzuki, Kenji; Matsuo, Hideki (Himeji Inst. of Tech., Hyogo (Japan) Fukushin Electric Co., Ltd., Hyogo (Japan))


    NiW {sub 2} B {sub 2} (M phase), existing in trinary Ni-W-B system, was measured in standard Gibbs free energy (GF) of formation in the temperature range from 1273K to 1423K by an electromotive force method (EMF) with use of solid oxide electrolyte. First, oxide phase in equilibrium with three-phase M-W-Ni solid solution region was confirmed to be B {sub 2} O {sub 3}. Binary Ni-W system solid solution in equilibrium with M phase and W phase is constant in composition with Ni-16.4mo1%W in the above temperature range. WO {sub 2} and WO {sub 2.72} were actually measured in GF. As Ni-W solid solution is in equilibrium with WO {sub 2} and WO {sub 2.72}, binary Ni-W system was measured in activity by the EMF, and Ni-16.4mo1%W solid solution was calculated in GF of mixing by use of the above measured GF of WO {sub 2} and WO {sub 2.72}. Finally with use of sample in M-W-Ni solid solution region, M phase was calculated in GF by the EMF. The result of those calculations were expressed with experimental formulas. 19 refs., 10 figs., 3 tabs.

  11. FY1995 study of highly efficient power generation system based on chemical-looping combustion; 1995 nendo chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu



    Synthesis of highly efficient and low emission power generation plant with chemical-looping combustion using various fuels such as natural gas, coal gas and hydrogen. Development of new looping materials with suitable reactivity, regenerative ability, and avoidance of carbon deposition. To obtain the design data for demo-plant by using the current experiment high- pressure fixed bed reactor. From the viewpoint of application of the proposed power generation system with chemical-looping combustion, the following main results were obtained. 1. New looping materials: NiO/NiAl{sub 2}O{sub 4}, CoO-NiO/YSZ, and Co{sub 3}O{sub 4}/CoAl{sub 2}O{sub 4}. These materials have high reactivity, repeatability, and avoidance of carbon deposition which play important roles in application of this new combustor. 2. NO{sub x} formation can be completely avoided; both fuel NO{sub x} in reduction reactor for coal gas as fuel and thermal NO{sub x} in oxidation reactor. 3. It is identified from the experiment using fixed bed reactor with the elevated pressure that NiO/NiAl{sub 2}O{sub 4} is a suitable material for coal gas or hydrogen. These promising results have provided valuable data for industrial application. (NEDO)

  12. Study on the improvement of toughness of Nb-based super high temperature materials by forming solid solution and composites; Niobuki chokoon zairyo no koyoka to fukugoka ni yoru kyojinsei kaizen ni kansuru kenkyu



    If materials superior to Ni-based and Co-based super alloys could be developed, great progress is expected in the energy source saving, enhancement of aircraft speed, and simplification of member structure. Metals having high fusing point are prospective as well as C/C composites and ceramics among possible materials. Especially, Nb has a similar density to Ni, and its fusing point is 1,000 centigrade higher than Ni. It has also ductility. Furthermore, it is characterized by the formation of solid solution with other various metals having high fusing point. Accordingly, Nb-based composite alloys having excellent high temperature strength as well as excellent ductility and toughness can be developed by enhancing the solid solution formation and the dispersion with composites of compound phases using Nb as a base material. The purpose of this study is to provide fundamental data for the development of Nb-based composite alloys. The optimum matrix materials and their fabrication processes have been investigated, to evaluate their high temperature properties. Consequently, it was found that the enhancement by the deposition of intermetallic compounds or by the dispersion of oxides was an effective method for the formation of composites of Nb-based alloys. 4 refs., 88 figs., 24 tabs.

  13. Improvement of the detection limits in radio-frequency-powered glow discharge optical emission spectrometry associated with bias-current conduction method; Jiko bias denryu donyuho ni yoru koshuha glow hoden hakko bunseki ni okeru kenshutsu genkai no kaizen

    Wagatsuma, K. [Tohoku University, Sendai (Japan). Research Institute for Materials


    A d.c. bias current driven by the self-bias voltage which is conducted through the r.f.-powered glow discharge plasma varies the emission characteristics drastically, leading to improvement of the detection power in the optical emission spectrometry. By conducting the bias currents of 20-30 mA, the emission intensities of the atomic resonance lines were 10-20 times larger than those obtained with conventional r.t.- powered plasmas. The detection limits for determination of alloyed elements in the re-based binary alloy samples were estimated to be l.6 x 10{sup -3}% Cr for CrI 425.43nm, 7 x 10{sup -4}% Mn for MnI 403.10nm, 1.9>10{sup -3}% Cu for CuI 327.40nm, 1.1 x 10{sup -3}% Al for AlI 396.16nm, and 6.6 x 10{sup -3}% Ni for NiI 352.45 nm. (author)

  14. Detection of strain behavior during phase-transformation in welds by the laser speckle method. Report 3. Application of the laser speckle method to strain masurement in the welding process; Reza supekkuru ho ni yoru yosetsubu no sohentai tojo no hizumi kenshutsu. 3. Reza supekkuru ni yoru hizumi sokuteiho no yosetsu eno tekiyo

    Muramatsu, Y.; Kuroda, S. [National Research Inst. for Metals, Tsukuba, Ibaraki (Japan); Gross, H-G. [Rostock Univ., Rostock (Germany)


    It corresponds to an information relating to defect formation due to residual stress and its accompanying defect formation to find out the period of phase-transformation and expansion volume on the transformation forming at welding. In order to estimate texture of the heat affected zone, there is an SH-CCT diagram, which is important on weld metallurgy. However, this is formed by giving a thermal recycling to a small size specimen under stress-free, which has some problems to estimate the transformation starting period in actual welding. And, the expansion volume containing the transformation cannot be found out directly by this. In this study, as the first step adaptable to this problem with laser speckle method measurable with non-contact and high precision, a linear heating with TIG to a SUS304 stainless steel thin plate without transformation was executed at first, the strain behavior accompanied with it was confirmed. Secondly, using a thin plate of 9% Ni steel showing any transformation at comparatively low temperature, probability of a phase transformation detection was investigated on a way of cooling by executing resemble linear heating. As a result, the laser speckle method was confirmed to be adaptable to this problem. 14 refs., 17 figs., 1 tab.

  15. BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

    Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College


    On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

  16. Formation of fine aggregate structure by solid-state displacement reaction of Ti with CoO or NiO. CoO oyobi NiO to Ti kan no koso chikan hanno ni yoru bisai fukugo soshiki no seisei

    Taimatsu, H; Kaneko, H [Akita Univ., Akita (Japan). Mining College; Wada, K [Akita Univ., Akita (Japan). Graduate School


    As a result of search for systems which have aggregate structures, the displacement reaction products of Ti with CoO or NiO are found to have aggregate structures in which the produced oxides and metals are entangled with each other. The displacement reaction of Ti with CoO or NiO is investigated at the temperature of 1273K. In the reaction of either couple, aggregate products are produced, and reacted layer is observed in the TiO2 matrix wherein Co or Ni phases are three dimensionally entangled in finely dispersed state of micron order. 2 layers of cavitated and dense TiO2 layers are found in the reacted layer. The thicknesses of the reacted layer are not constant according to locations, but thick portions are grown obeying the parabolic rate law. As a result of the study on the possibility of fabricating cermet by the reaction between powders, finely mixed characteristic structures are found to be easily obtained using systems which can produce aggregate structures. 24 refs., 9 figs.

  17. FY 1998 annual report on the decomposition/removal of harmful compounds in the gaseous phase by porous membrane provided with a catalytic function; 1998 nendo shokubai kinotsuki fuyo takomaku ni yoru kisochu yugai busshitsu no bunkai jokyo chosa hokokusho



    Harmful compounds, e.g., dioxins and nitrogen oxides, released into the air are causing severer environmental problems on a global scale. In order to solve these problems, it is necessary to efficiently remove the released compounds in the vicinity of the living environments, while preventing, as far as possible, their formation at the sources. An attempt has been made to develop porous membranes impregnated with composites of a variety of metallic oxides showing activities as photocatalysts and for dark reactions by the ion engineering method, in order to drastically solve the above problems. Described herein are the FY 1998 results. Thin films of various titanium oxide crystals (anatase, rutile, and their combinations) are formed on Si substrates by the ion engineering method, as the photocatalysts for decomposition of aldehyde and water (for hydrogen production), to validate the optimum crystalline structures for the photocatalysis. Porous bodies of Ni and carbon are also impregnated with anatase TiO{sub 2} for decomposition of harmful gaseous compounds and water, to validate the effects of the porous membranes provided with catalytic functions. (NEDO)

  18. Design of environment-friendly and next generation-type conversion system for unused carbon resources by developing highly functional materials; Kokino zairyo kaihatsu ni yoru kankyo chowagata jisedai miriyo tanso shigen tenkan system no kochiku

    Wakabayashi, K; Morooka, S; Arai, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sakanishi, K [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study


    Studies are conducted for the development of now-unused kinds of fossil carbon resources, such as low rank coal and heavy gravity crude oil, into higher-value liquid fuel. In the preliminary treatment process, the fossil carbon resources are dried by use of supercritical carbon dioxide, when it is found that the resources are disintegrated and water is desorbed. In a low rank coal liquefaction process using the NiMo/KB (Kefjen Black) catalyst, more than 60% is converted into oil, which rate is improved by use of the dual-temperature liquefaction process. This catalyst may be recovered by separation utilizing specific gravity difference. As a low temperature gasification catalyst, the alkaline carbonate-carried carbon catalyst is very quick at the initial stage of reaction. The perovskite-carried alkaline carbonate catalyst is high in carbon oxidizing/activating efficiency at low temperatures. The silica film deposited on an alumina-coated support tube is excellent in selectivity and speed as a hydrogen separating film, and a carbonized polyimide film as a carbon dioxide separating film. For the supercritical phase adsorption/separation of chemicals not to be distilled easily, the NaY-type zeolite functions effectively. Pd/ZrO2 serving as a carbon monoxide conversion catalyst enables the recovery of more MeOH when Pd grains are smaller in diameter.

  19. Ultrasound imaging with a micromotor; Micromotor ni yoru choonpa imaging

    Oshiro, O.; Salimuzzaman, M.; Matani, A.; Chihara, K. [Nara Institute of Science and Technology, Nara (Japan); Asao, M. [Osaka National Hospital, Osaka (Japan)


    This paper describes a new ultrasound intravascular imaging system. In this system, an ultrasound probe consists of a micromotor, an ultrasound reflecting mirror attached with the micromotor and an ultrasound transducer. Ultrasound is scanned radially by a micromotor instead of a rotation transmitting wire and the rotation of the micromotor is performed and controlled by an external magnetic field. This ultrasound imaging system with a micromotor was applied to observe the inside of blood vessels through in vitro experiments. The preliminary results suggest that this system has the sufficient ability to define the blood vessel morphology and that the simple image processing enhances signal-to-noise ratio of the reconstructed image. 12 refs., 5 figs.

  20. Laser beam cutting method. Laser ko ni yoru kaitai koho

    Kutsumizu, A. (Obayashi Corp., Osaka (Japan))


    In this special issue paper concerning the demolition of concrete structures, was introduced a demolition of concrete structures using laser, of which practical application is expected due to the remarkable progress of generating power and efficiency of laser radiator. The characteristics of laser beam which can give a temperature of one million centigrade at the irradiated spot, the laser radiator consisting of laser medium, laser resonator and pumping apparatus, and the laser kinds for working, such as CO{sub 2} laser, YAG laser and CO laser, were described. The basic constitution of laser cutting equipment consisting of large generating power radiator, beam transmitter, beam condenser, and nozzle for working was also illustrated. Furthermore, strong and weak points in the laser cutting for concrete and reinforcement were enumerated. Applications of laser to cutting of reinforced and unreinforced concrete constructions were shown, and the concept and safety measure for application of laser to practical demolition was discussed. 5 refs., 8 figs.

  1. Environment purification using microorganisms. Biseibutsu ni yoru kankyo joka

    Tanaka, H [Asahi Glass Co. Ltd., Tokyo (Japan); Harada, S


    Technologies to purify polluted soils vary with kinds of pollutants, spread of pollution, and shapes of water veins. A method is used often that several wells are drilled in a polluted area, and water is circulated between upstream wells and downstream wells, where activities of microorganisms living in that particular environment are utilized to biodegrade the pollutants. This technology is called bioremediation. This paper deals with soil pollution by chemical substances, and describes development of a technology to remove pollution caused by PCB and petroleum which is thought difficult to apply the bioremediation technology among environment purifying technologies using microorganisms. The bioremediation of petroleum pollution assumes petroleum pollution on seashores. Discussions have been given on separation from sea water of petroleum decomposing microorganisms to be used in the bioremediation, and the number of petroleum decomposing bacteria in seas near Japan. As a result, it was made clear that a few kinds of bacteria will suffice for decomposition of main components in a mixture as complex as petroleum. 5 refs., 4 figs.

  2. Development of new supervisory system with ITV. ITV ni yoru kanshi system ni kansuru kenkyu

    Shimonaga, S; Matsunaga, R; Ono, H [The Kyushu Electric Power Co. Inc., Fukuoka (Japan)


    This paper describes an automatic trespassing supervisory system with ITV and picture processing (PP). The paper details an integrated control system and automatic supervision. The system functions to automatically detect a trespassing by means of PP, transfers items of information collected by sensors to a remote control center, and records relevant data. The operation principle consists of measurement of change in two or more images of moving bodies with binary value at a certain interval, determination on acceptability of the moving bodies represented by human characteristics, and identification of a trespasser. The system consists of an automatic supervisory device using PP and an automatic patrolling and searching device by means of sensor measurements. The supervisory device has images outputted from ITV and VTR processed by PP, host computer, and HD, and linked to an indication mechanism. According to the result of a site test at wireless transmission station of Kyushu Electric Power Company, the difference between measurement values collected by the searching device and those by the supervisory device was [plus minus]3% or less (other than EG output current), which is a useful value for verification. Although the basic technique has been established, practical use of the system still has some problems including performance improvement in picture processing. 37 refs., 38 figs., 18 tabs.

  3. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on transportation of hydrogen in the form of metallic hydride; 1974-1980 nendo kinzoku suisokabutsu ni yoru suiso no yuso gijutsu no kenkyu seika hokokusho



    This report concerns the transportation and storage of hydrogen using metallic hydrides that perform absorption and desorption of hydrogen. Alloys useable for this purpose have to be capable of reversibly absorbing and desorbing hydrogen within a certain temperature range. In the absence of guidelines to follow in the quest for such alloys, the efforts at discovering them turned out to be a continual series of trials and errors. Researches were conducted into the hydrogenation reaction of Mg and Mg-based alloys and into hydrides of V-based alloys, and into Zr-based alloy hydrides such as the ZrMn{sub 2} hydride, ZrNiMn hydride, Zr(Fe{sub x}Mn{sub 1-x}){sub 2} hydrides, TiZrFe{sub 2} hydride, Zr{sub x}Ti{sub 1-x}(Fe{sub y}Mn{sub 1-y}) hydrides, etc. Also studied were the electronics of hydrogen in metallic hydrides, rates of reaction between Mg-Ni-based alloys and hydrogen systems, endurance tests for hydrides of Mg-Ni-based alloys, effects exerted by absorbed gas molecules during the storage of hydrogen in Mg-Ni-based alloys, effective thermal conductivity in a layer filled with a metallic hydride, metallic hydride-aided hydrogen transportation systems, chemical boosters, etc. (NEDO)

  4. Achievement report on research and development in the Sunshine Project in fiscal 1980. Research on a hydrogen manufacturing technology by using thermo-chemical method. (Research on equipment materials for iodine system cycle); 1980 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle no sochi zairyo no kenkyu



    This paper describes research on materials of equipment for the second stage reaction in relation with development on a hydrogen manufacturing technology by using the iodine system cycle in the thermo-chemical method. The second stage reaction produces MgO, I{sub 2} and O{sub 2} by decomposition of Mg(IO{sub 3}){sub 2} at 600 to 650 degrees C. Corrosion tests were carried out by using 25Cr-20Ni steel and Ni-50Cr alloy having shown relatively high corrosion resistance in the researches to date, which were added with trace amount of different alloy elements. The tests were performed in gas mixture of I{sub 2}, O{sub 2} and H{sub 2}O at 600 to 700 degrees C for 48 to 192 hours. The average corrosion rate of 25Cr-20Ni steel was reduced by adding Y(0.2%), Ca (0.2%) or Si+Al (1%Si+1%Al), by which relatively uniform corrosion pattern was shown, and the corrosion resistance was improved remarkably. The average corrosion rate of 25Cr-20Ni steel showed a trend of increasing by adding Si and Nb, and non-uniform corrosion like pitting has occurred, revealing that it is not preferable from the aspect of corrosion resistance. The average corrosion rates of the tested materials tended to become somewhat greater under heat insulated condition than under continuously heating condition. Effect of Mg(IO{sub 3}){sub 2} deposition is very small. (NEDO)

  5. Achievement report on research and development in the Sunshine Project in fiscal 1979. Research on hydrogen manufacturing technologies (Research on equipment materials for iodine system cycle); 1979 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle no sochi zairyo no kenkyu



    From among researches on hydrogen manufacturing technologies using thermo-chemistry in the Sunshine Project, discussions were given on equipment materials, with the second-stage reaction in the iodine system cycle as the object. This paper describes achievements in fiscal 1979. The reaction produces MgO, I{sub 2} and O{sub 2} from Mg(IO{sub 3}){sub 2}. Corrosion tests were performed by using test pieces made of Ni alloy, iron-Ni-Cr alloy, Ti alloy, Zr alloy, Nb and Ta. These materials are thought to have excellent corrosion resistance in high temperature gaseous phase composed of iodine, oxygen and water. Corrosion tests were carried out also by using sheet formed test pieces of 24 kinds of alloys and six kinds of commercially available non-ferrous metallic materials in different temperatures and atmospheres, mainly the iodine plus oxygen plus H{sub 2}O mixed gas atmosphere at 600 degrees C. The corrosion resistance of the tested materials can be divided into three ranks. Materials having relatively good resistance were Ni-50Cr alloy and Co group alloy. Materials having good corrosion resistance are very little affected by water content. The higher the temperature, the more the metal corrosivity has increased. Preliminary discussions were given on pipe formability in materials having good corrosion resistance as the equipment piping materials. Their mechanical properties were also tested. This paper also describes corrosion resistance tests under heat transferring condition by using pipe-formed test pieces. (NEDO)

  6. Cooperative measurements of microtremors in the north-eastern region of Nishinomiya city, Hyogo Pref.; Nishinomiyashi hokutobu ni okeru joji bido no godo kansoku

    Maiguma, T; Matsuzawa, H [Saitama University, Saitama (Japan). Faculty of Engineering; Sawada, Y; Tazawa, Y [Central Research Institute of Electric Power Industry, Tokyo (Japan)


    For the purpose of generally grasping space distribution of ground vibration characteristics, cooperative measurements were conducted in a wide area, mainly in the area stricken by the M7 earthquake. Forty-five organs such as governmental institutes, universities, and private company institutes participated in the measurements which were conducted at 1967 measuring points. The area which the author is in charge is an area from the north of Nishinomiya City to the south of Takarazuka City. The area is relatively far from the hypocenter area, but the magnitude is 7 there and damage was concentrated. The measurements were made by each independent team from August 29 to September 1, 1995. As a result of spectral measurements of NS, EW and UD components, conspicuous peaks were seen in an extent of 1.5 sec. cycle in almost all measuring points and components. Further, in spectra of horizontal motion components of A measuring point group, conspicuous peaks were seen in an extent of 0.15-0.5 sec. cycle, and in those in B and C measuring point groups, in an extent of 0.35-0.5 sec. cycle. In upper/lower motion components, conspicuous peaks were seen in an extent of 0.3 sec. cycle in A measuring point group. 4 figs.

  7. Magnetotelluric investigation in and around southern part of Hidaka metamorphic belt in Hokkaido, Japan; Hidaka henseitai nanbuiki ni okeru MT kansoku

    Sato, H; Utsugi, M; Hirano, K; Doi, T; Nishida, Y; Arita, K [Hokkaido University, Sapporo (Japan)


    An MT observation was conducted in the Hidaka district, Hokkaido, for the estimation of the 2D resistivity structure in the southern part of the metamorphic belt, when frequencies of the VLF, ELF, and ULF bands were used. An approximately 42km-long traverse line was set to cross the Hidaka metamorphic belt from east to west. As for the observation points, 48 VLF points, 16 ELF points, and 4 ULF points were provided. During the data processing, impedance tensor was calculated in the frequency domain for the determination of the apparent resistivity relative to frequency and the phase difference. As the result, it was found that there is a fairly large resistivity gap between observation spots MNS and KWR and that the boundary corresponds to the Hidaka metamorphic belt, that the metamorphic belt that is reflected as a conspicuous high-resistivity layer in the VLF-, ELF-MT slopes down toward the east and has a distribution as deep as 10km in the vicinity of observation point KWR, that this high-resistivity layer sandwiches a low-resistivity layer at a depth of 5-7km, and that on the east side of the metamorphic belt there is a medium-resistivity layer creeping under the belt from the east side toward the west side. 5 refs., 6 figs.

  8. Measurement of radiation and temperature of cathod spots in excimer laser discharge; Ekishima reza reiki hodennai ni fukumareru inkyoku kiten no kogakuteki kansoku to ondo no sokutei

    Minamitani, Y.; Nakatani, H. [Mitsubishi Electric Corp., Tokyo (Japan)


    Excimer laser is used in various fields such as luminous source for steppers, annealing treatment, ablation process, nuclear fusion and so on. In this paper, the radiation timing and gas temperature of cathode spots, streamer discharges and glow discharges in KrF excimer are measured by observing the radiating spectra thereof. The following conclusions are obtained from the results of the present study. Cathode spots begin to radiate at about 20ns after the discharge initiation, then the first and second radiation peaks are observed respectively when the discharge current reversing after passing zero point and the reserved discharged current approaching zero point. Streamer discharge makes flashover between electrodes at the second radiation peak of cathode spots, while the glow discharges almost disappear when streamer discharges occurring. The temperatures of cathode spots and glow discharge as 5500K and 2600K respectively are almost constant and independent upon the discharging voltage of laser. 14 refs., 12 figs.

  9. Array measurements of long-period microtremors in southwestern Kanto plain, Japan; Kanto heiya nanseibu ni okeru yaya choshuki bido no array kansoku

    Yamanaka, H; Sato, H; Kurita, K; Seo, K [Tokyo Institute of Technology, Tokyo (Japan)


    Array measurements of long-period microtremors were carried out in the southwestern part of Kanto Plain, Japan, to obtain S-wave velocity structures in sedimentary beds as fundamental data for estimating long-term strong ground motion in Kanto Plain. The major component in a long-term seismic motion observed in Kanto Plain is the surface wave. According to the result of observations on Love wave by Kinoshita et al, the wavelengths of the surface waves of a long-term cycle are 10 to 20 km. Therefore, if an array observation is to be performed at intervals of about two wavelengths, about 40 points will be required to cover the entire Kanto plain. The final phase velocity is decided by averaging phase velocities of each cycle obtained for each data set. The acquired phase velocities are analyzed inversely by using a genetic algorithm to derive the S-wave velocities at each observation point. The present microtremor array observation has used 13 points in the southwestern part of Kanto Plain to acquire S-wave velocity (Vs) distribution in sedimentary beds. It was made clear that beds with Vs of 1.0 km/s and Vs of 1.5 km/s exist in this area between the surface bed and the seismic foundation with Vs of about 3 km/s. 10 refs., 10 figs., 1 tab.

  10. Observations and analysis of free groundwater levels and groundwater pressure in landslide slopes. Jisuberi shamen no jiyu chikasuii, chikasuiatsu no kansoku to kaiseki ni tsuite

    Yoshida, S; Nakano, T [Niigata Univ., Niigata (Japan). Faculty of Agriculture; Inaba, K [Niigata Univ., Niigata (Japan). Graduate School; Sato, O [Niigata Univ., Niigata (Japan)


    It is well known that the landslides in Tertiary systems abundantly found in Niigata Prefecture, etc., frequently occur especially in the snow melting season or the heavy rain season. For studying the occurrence of such landslides, exploration of the actual condition of groundwater and evaluation of the strength of earth are very important even when the landslide occurring mechanism can be presumed in a relatively simple way about the soil mechanics. Therefore, great importance is attached to the observation and investigation on the groundwater level and pressure at landslide sites and stability analyses have been actively performed. However, it is considered that several fundamental problems still exist in the method for estimating the groundwater level and pressure in landslide slopes from the observation method and data on groundwater levels and pressure (pore pressure). In this paper, these fundamental problems are examined on the basis of concrete observations made by the writers on landslide slopes at Matunoyamagoe and Higashimusikame landslide sites in Niigata Prefecture for the past several years. 6 ref., 6 figs., 2 tabs.

  11. Analysis of vibration characteristics of a prestressed concrete cable-stayed bridge using strong motion observation data. Jishin kansoku ni motozuku PC shachokyo no shindo tokusei no kaiseki

    Inatomi, T. (Port and Harbour Research Institute, Kanagawa (Japan)); Takeda, T.; Obi, N.; Yamanobe, S. (Kajima Corp., Tokyo (Japan))


    Records of seismic observation were analyzed for the purpose of proving the validity of antiseismic design for a prestressed concrete (PC) cable-stayed bridge. This bridge is a three span continuous PC cable-stayed bridge of 498 m in bridge length, and is constructed on alluvial soft ground. The seismometer used is a servo type accelerometer. The observed frequency and mode of seismic vibration are in good agreement with those in the analysis and hence the validity of modelling of the structure in designing was confirmed. It was also confirmed that the bending vibration and torsional vibration of the main girder are separated as designed. However, some points such as a large difference in the observed vibration and analysed vibration in the mode accompanying rotation of the base are listed as problems to be solved in antiseismic design. In order to investigate the attenuation constant of the upper structure, a seismic wave response analysis was performed and its results were compared with observed ones. When the attenuation constant is assumed to be 2%, agreement of data between analysis and observation is good, and it is considered that the attenuation constant of the upper structure only without the effects of attenuation of energy escape from the base and crack generation in concrete was about 2% in the observed earthquake (maximum acceleration on the ground: 51 Gal). 8 refs., 9 figs., 2 tabs.

  12. Detection of seismic phases by wavelet transform. Dependence of its performance on wavelet functions; Wavelet henkan ni yoru jishinha no iso kenshutsu. Wavelet ni yoru sai

    Zeng, X; Yamazaki, K [Tokyo Gakugei University, Tokyo (Japan); Oguchi, Y [Hosei University, Tokyo (Japan)


    A study has been performed on wavelet analysis of seismic waves. In the wavelet analysis of seismic waves, there is a possibility that the results according to different wavelet functions may come out with great difference. The study has carried out the following analyses: an analysis of amplitude and phase using wavelet transform which uses wavelet function of Morlet on P- and S-waves generated by natural earthquakes and P-wave generated by an artificial earthquake, and an analysis using continuous wavelet transform, which uses a constitution of complex wavelet function constructed by a completely diagonal scaling function of Daubechies and the wavelet function. As a result, the following matters were made clear: the result of detection of abnormal components or discontinuity depends on the wavelet function; if the Morlet wavelet function is used to properly select angular frequency and scale, equiphase lines in a phase scalogram concentrate on the discontinuity; and the result of applying the complex wavelet function is superior to that of applying the wavelet function of Morlet. 2 refs., 5 figs.

  13. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on hydrogen production technology using thermochemical method (Research on iodine-based cycle etc.); 1974-1980 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle nado no kenkyu



    Iodine-alkaline earth metal (Mg, Ca) cycles are discovered, and the one with Mg is found excellent. The reaction consists of four stages, that is, Stage (1) where 1/5Mg(IO{sub 3}){sub 2}+MgI{sub 2}(aq) is obtained from 6/5MgO+6/5I{sub 2}, Stage (2) where 1/5MgO+1/5I{sub 2}+1/2O{sub 2} is obtained from 1/5Mg(IO{sub 3}){sub 2}, Stage (3) where MgO+2HI is obtained from MgI{sub 2}+H{sub 2}O, and Stage (4) where H{sub 2}+I{sub 2} is obtained from 2HI. Since there is much iodine and water at Stage (1), MgO thrice MgI{sub 2} in mol is added for reforming and concentration. At Stage (4), where the decomposition rate is as low as 17-27% with the equilibrium dissociation reaction proceeding at 300-700 degrees C, hydrogen is selectively separated by permeation through a porous diaphragm for the acceleration of the reaction. As for materials for the device, they are narrowed down to high-priced ones, that is, Ta and Nb for Stage (1), Ni-50Cr for Stage (2), and Mo etc. for Stages (3) and (4). Under the circumstances, a study is started for the development of a chemical vapor plating process which is high in corrosion resistance. Other cycles such as sulfur-based cycles and hybrid cycles are also investigated. (NEDO)

  14. Faults survey by 3D reflection seismics; Sanjigen hanshaho jishin tansa ni yoru danso chosa

    Tsuchiya, T; Ejiri, T; Yamada, N; Narita, N; Aso, H; Takano, H; Matsumura, M [Dia Consultants Company, Tokyo (Japan)


    This paper describes fault survey by 3D seismic reflection exploration. Survey has been conducted mainly at flat land area without pavement not in urban area in Japan. Subsurface structure is complicated with intersecting multiple faults. In this area, a lot of geological investigations have been done prior to the seismic reflection exploration. Fairly certain images of faults have been obtained. However, there were still unknown structures. Survey was conducted at an area of 170m{times}280m in the CDP range. Measurements were carried out by using 100 g of dynamite per seismic generation point combined with 40 Hz velocity geophones. Fixed distribution consisting of lattice points of 12{times}12 was adopted as an observation method. In and around the lattice, a great number of explosions were carried out. The CDP stacking method and the method of migration after stacking were used for the data processing. The 3D structures of six horizons and five faults could be interpreted. Interpreted horizons were well agreed with the logging results. 3 figs.

  15. Air environment purification using photocatalyst. Hikari shokubai ni yoru taiki kankyo joka

    Takeuchi, K [National Institute for Resources and Environment, Tsukuba (Japan)


    Noticing that metal oxides have photocatalysis for reduction in NOx concentration and examining effects of the TiO2 selected on removal of pollutant, the paper proposes a direct purification method for the air environment. Since TiO2 causes electron excitation meeting near ultraviolet irradiation, it manifests a catalytic function for various oxidation/reduction reactions. Details of the reaction mechanism are unknown, various active oxygen species generated on the surface of TiO2 under light irradiation oxidize NOx and acquire it as nitric acid on the surface. It is found that mixture of activated carbon of low hygroscopicity with TiO2 is effective to prevent a tendency of NO to desorb before NO becomes nitric acid. What 40% of the catalyst with fluorine resin is formed into like a sheet shows a high removal rate even in the amount of ultraviolet irradiation in a winter cloudy day in the wide range of 0.5 - 95.0% of NOx and SO2, and if the photocatalyst is applied to the side wall of city buildings, the NOx concentration is estimated to be reduced by as much as 20%. 5 refs., 3 figs.

  16. Foods hygiene management according to HACCP.; HACCP ni yoru shokuhin eisei kanri

    Seki, T [Niigata Enginering Co., Ltd., Tokyo (Japan)


    New foods hygiene management system HACCP(Hazard Analysis and Critical Control Point) was explained, which prevents food poisoning. Followings are described; (1) Outline of HACCP, (2) History of HAPPC, (3) Process to perform HACCP, (4) Infrastructure for HACCP, (5) How to promote HACCP, (6) Certification system in Japan. HACCP secures the safety in foods hygiene by making rules of Critical Control Points (CCP) on foods hygiene and by administrating strictly their performance. Details of works, frequency and person in charge of the work and methods to confirm and record the work are prescribed in PP (Prerequisite Program) and SSOP (Sanitation Standard Operation Procedure). (NEDO)

  17. Archaeological prospecting by DEF method; Denkai zansaho ni yoru iseki tansa

    Kishikawa, H; Aono, T; Tanaka, T; Mizunaga, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    A study is made of a newly-developed differential electric field (DEF) method, wherein potentials between potential electrodes equidistant from a current electrode is measured for directly detecting the secondary potential attributable to an anomalous-resistivity body. In this method, a current is fed into the ground from a point source C1, and four potential electrodes, two each on the X-axis and Y-axis, are provided equidistant from the point source C1 for the measurement of the potentials in the directions of X and Y. Numerical experiments and field experiments in a playground were conducted for this DEF method, and it was found that this method is effective in detecting an anomalous-resistivity bodies (ruins, etc.) situated in a homogeneous medium or in a horizontal multi-layer structure, is capable of displaying anomalous vectors enabling the estimation of the direction from the observation point of the anomalous-resistivity body, improves on work efficiency over the conventional mapping method, enables the estimation of the boundary of the anomalous-resistivity body on the basis of the peak of the anomalous electric field residue on the display, and that the obtained data can be easily processed by use of a personal computer on the site. 3 refs., 9 figs.

  18. Characterization of earthquake fault by borehole experiments; Koseinai sokutei ni yoru jishin danso no kenshutsu

    Ito, H; Miyazaki, T; Nishizawa, O; Kuwahara, Y; Kiguchi, T [Geological Survey of Japan, Tsukuba (Japan)


    A borehole was excavated to penetrate the Nojima fault at the Hirabayashi area, to investigate the underground structures of the fault by observation of the cores and well logging. The borehole was excavated from 74.6m east of the fault surface. Soil is of granodiorite from the surface, and fault clay at a depth in a range from 624.1 to 625.1m. Observation of the cores, collected almost continuously, indicates that the fault fracture zone expands in a depth range from 557 to 713.05m. The well logging experiments are natural potential, resistivity, density, gamma ray, neutron, borehole diameter, microresistivity and temperature. They are also for DSI- and FMI-observation, after expansion of the borehole. The well logging results indicate that resistivity, density and elastic wave velocity decrease as distance from fault clay increases, which well corresponds to the soil conditions. The BHTV and FMI analyses clearly detect the fault clay demarcations, and show that elastic wave velocity and BHTV results differ at above and below the fault. 3 refs., 3 figs.

  19. Ground water contamination by electrical prospecting; Denki tansaho ni yoru chikasui osen chosa

    Irie, S; Fujii, Y; Sakaguchi, S; Ushijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    A report is made about the result of vertical electric sounding conducted in the MK district, Fukuoka City, where Kyushu University is about to move. As for the method of electrical prospecting, in consideration of the need for probing a depth of 50m at the shallowest, vertical electrical sounding with a Schlumberger array of electrodes was employed. Measurements were made for 57 locations on the planar ground, the interval between electrodes gradually increased from 1 to 200m. In the 2D structure model analysis, a 2D inversion program was utilized in the ABIC minimization method. Also investigated were the relationship of electric prospecting and the geology, geological conditions, water level in the well, water quality, salt water, and pore rate from the previously-conducted investigative boring. As the result, it was estimated that the boundary between the first and second layers detected by electric prospecting reflected the level of underground water and that the boundary between the second and third layers reflected the portion where the N-value sharply increases. 4 refs., 8 figs.

  20. Seismic traveltime tomography by use of gridpoints discritization; Koshitenho ni yoru danseiha tomography kaiseki

    Hirai, T; Watanabe, T; Sassa, K [Kyoto University, Kyoto (Japan). Faculty of Engineering


    Efforts were made to enhance analytical precision and stabilize the results in seismic traveltime tomography by use of a method wherein the velocity distribution is expressed as a continuous function interpolated by parameters respectively assigned to the gridpoints. In this method, the slowness data are regarded as the parameters respectively assigned to the gridpoints, and the slowness value at a given point is determined after interpolation by the gridpoints surrounding the said point. A method based on the variation principle was used for ray tracing. As the result, it was confirmed that this method determines the ray path and traveltime with high precision. A method of least squares using Lagrange`s multiplier was applied for inversion. Comparison was made between the use of cells and the use of gridpoints in the results of inversions performed for an inclined 4-layer structure model, when it was found that the values involving the boundaries between layers, inclinations of the layers, and velocities of seismic waves are ambiguous with the cells while those with the gridpoints are reconstructed roughly correctly. 5 refs., 7 figs., 1 tab.

  1. Sewage disposal using anaerobic membrane reactor. Kenkiseimaku reactor ni yoru gesui shori

    Fujita, Y. (Dic-Degremont Co. Ltd., Tokyo (Japan))


    Discussions were given on a small-scale sewage disposal of about bod 200 mg/l, for which no many examples of use have been hitherto available, using a system combining an anaerobic reactor and membrane modules. Experiments had been carried out from 1988 through 1990 as a part of the Aqua-Renaissance Project. The test equipment wza installed in the premises of the Chigasaki Coastal Research Facilities operated by the Ministry of International Trade and Industry, which used sewage flowing from the adjoining sewage treatment plant for the southern area of the Fujisawa City. The test facility consisted of a system comprising a pretreatment facility, SS decomposing reactor, fluid-bed reactor, separation membrane modules, nitrogen removing facility and micro-organism activity measurement. The test facility was constucted assuming a treatment of 10 m{sup 3} a day. The system was divided into a composite system, A system and B system to operate the system in simplified flows. As a result of comparing the composite system, A system and B system, it was found that B system can deal with wider range of disposal for a small-scale sewage treatment of about 1000 m{sup 3} a day. 6 refs., 14 figs., 3 tabs.

  2. Evaluation of environmental impact by LCA method. LCA shuho ni yoru kankyo fuka hyoka

    Sakamura, H.; Utsuno, F.; Yasui, I. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)


    This paper explains the concept, history, and analytic methods of life cycle assessment (LCA), showing its application to beer bottles and cement factories as specific examples. The LCA is a method to calculate substances and energies put into the whole process of production of a product from raw material mining to product wasting and environmental loads emitted therefrom. It also evaluates the result collectively and quantitatively. A first case of the research is reportedly the one performed at Coca-Cola Co., Ltd. in 1969. Full-scale researches have gone forward in European countries in the recent several years, and are progressing to international networks. The analytic methods can be divided largely into an accumulation method to analyze data in each process and add them up, and a method to use an industrial association table. The former method is the most generally used method currently in overseas countries if referred to the LCA. Because the LCA can cause the analytic result and evaluation to vary depending on the purpose, it is important to define the goal, and set the scope. The LCA must develop in the future although it has a number of problems. 10 refs., 5 figs., 2 tabs.

  3. Laser material purification of neodymium. Hikari reiki seiseiho ni yoru neodymium no kojundoka

    Ogawa, Y.; Ozaki, T.; Yoshimatsu, S. (National Research Institute for Metals, Tokyo (Japan)); Chiba, K.; Umeda, H.; Saeki, M. (Nippon Steel Corp., Tokyo (Japan))


    Selective photoexcitation and photoionization of neodymium atoms were studied basically by using laser. Also, using their properties, feasibility of laser material purification (LPM) technology in gaseous phase was presented. In the selective 3-step ionization, laser beam with two kinds of proper wave length causes resonance exitation of the target element, which goes up to the excitation level of the first step, and the element is ionized by the second laser beam and the third laser beam. The 3-step ionization scheme by a single wave length laser beam of 577.612nm was used for the ionization of Nd. Nd ionized selectively by laser beam was recovered as thin layer at the negative potential side of plane electrodes placed at both sides of the laser irradiation area. In the layer formed by the TPD technology with this scheme, it is possible to decrease impuritis such as Pr by 1/16 and to form highly purified thin layer. 13 refs., 12 figs., 1 tab.

  4. Surface photo reaction processes using synchrotron radiation; Hoshako reiki ni yoru hyomenko hanno process

    Imaizumi, Y. [Tohoku University, Sendai (Japan). Institute for Materials Research; Yoshigoe, A. [Toyohashi University of Technology, Aichi (Japan); Urisu, T. [Toyohashi University of Technology, Aichi (Japan). Institute for Molecular Science


    This paper introduces the surface photo reaction processes using synchrotron radiation, and its application. A synchrotron radiation process using soft X-rays contained in electron synchrotron radiated light as an excited light source has a possibility of high-resolution processing because of its short wave length. The radiated light can excite efficiently the electronic state of a substance, and can induce a variety of photochemical reactions. In addition, it can excite inner shell electrons efficiently. In the aspect of its application, it has been found that, if radiated light is irradiated on surfaces of solids under fluorine-based reaction gas or Cl2, the surfaces can be etched. This technology is utilized practically. With regard to radiated light excited CVD process, it may be said that anything that can be deposited by the ordinary plasma CVD process can be deposited. Its application to epitaxial crystal growth may be said a nano processing application in thickness direction, such as forming an ultra-lattice structure, the application being subjected to expectation. In micromachine fabricating technologies, a possibility is searched on application of a photo reaction process of the radiated light. 5 refs., 6 figs.

  5. Analysis of bending process using forming simulation; Seikei simulation ni yoru press niji seikei kaiseki

    Hamaguchi, T; Ogawa, T; Tamai, H [Mazda Motor Corp., Hiroshima (Japan)


    FEM simulation system is becoming an effective tool in the production engineering, especially in the evaluation of press formability. We have been applying it to the evaluation of defect phenomena, such as breakage and wrinkling, which occur in the drawing process to produce auto body parts. We tried a new application which treat dimensional precision and the other defect in the flanging or bending process after trimming. In this paper, we introduced the result of development and an example applied in the analysis. 1 refs., 8 figs.

  6. Synthesizing aspartyl-phenylalanine methyl precursor by enzymatic method. Kosoho ni yoru asuparutemu zenkutai no gosei

    Hirata, M. (Waseda University, Tokyo (Japan)); Hirata, A. (Waseda University, Tokyo (Japan). School of Science and Engineering)


    Demand for aspartyl-phenylalanine methyl, an amino acid based artificial sweetener, is increasing for use by people on diet. The material is manufactured by making a precursor through dehydrating and condensing N-protective{sub L}-asparagine acid and {sub L}-phenylalanine methyl ester, and then removing the protective group. While the manufacturing methods include chemical process and enzymatic process, this paper introduces various researches done mainly by the latter process. The enzymatic process is simpler and safer than the chemical process, allowing experiments to be carried out easily. However, since the reaction equilibrium is biased more on the decomposition side than the synthesis side, it should be shifted to the synthesis side. Such operations may be carried out as separating the products simultaneously with the reaction, adding organic solvents, and operating the reaction in an organic solvent. The last operation, for example, reduces the concentration of liquid produced by the reaction by use of either water soluble or slightly soluble organic solvent, and improves the yield. It also has an advantage that relatively stable fixing enzymes can be adjusted by use of hydrophilic carriers. 68 refs., 8 figs.

  7. Heightening in efficiency of biological treatment by additives. Tenkazai ni yoru seibutsu shori no koritsuka

    Ishikawa, M. (Fukui Institute of Technology, Fukui (Japan))


    The activated sludge process and other biological treatments, though utilized for most sewerage and drainage water disposals, often necessitate the maintenance to be managed with a professional knowledge so that confrontation is oftem impossible with trouble in management. In the present report, different basic studies are to be introduced of microbial activation by an addition with saponin. Saponin'', etymologically identical with savon'' and soap'', has been being used as natural cleaner, emulsifier and foamer in South America and Europe since olden times, and is used also for the processed food and potable water in the USA. The present experiment concluded that, in case of using it as microbial activator, the activated sludge can be considerably increased in load quantity of disposal by the heightening in oxygen-supplying power, high concentration microbial maintenance, microbial activation, etc. In the future, there will remain many problems unsolved such as what is the optimized condition for the addition depending upon the condition of base material. 3 refs., 6 figs., 1 tab.

  8. Long distance energy transfer via electromagnetic waves. Denjiha keitai ni yoru energy no chokyori yuso

    Matsumoto, H. (Kyoto University, Kyoto (Japan))


    This paper describes the following matters on electric power transportation using microwaves: the world's first microwave power transmission experiment, MINIX, was carried out in Japan in 1986; power transportation using microwaves requires developing high-efficiency amplifiers, power receiving systems, and high-accuracy microwave controlling techniques; the transportation system has problems discussed on effects of microwave beams on living organisms and the existing communication networks, and atmosphere-plasma interactions on transmission paths; and a MILAX experiment was carried out in Japan in 1992, which transmitted power using a microwave of about 2.4 GHz and succeeded in flying a model airplane at an altitude of about 10 meters for about 40% seconds. The technology developed from this experiment is scheduled to be used for an ISY-METS rocket experiment in January 1993. This experiment is an extension of the MINIX experiment to transmit power using microwaves in ionosphere plasma. 30 refs., 7 figs.

  9. Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

    Ishizaki, T [Ministry of Transportation, Tokyo (Japan)


    With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

  10. Measurement of crack in rock using transmitted elastic wave; Toka danseiha ni yoru ganbannai kiretsu keisoku

    Tomishima, Y [National Institute for Resources and Environment, Tsukuba (Japan)


    With an objective to measure at high accuracy the positions and sizes of cracks existing in rocks, a theoretical study has been carried out on a method which utilizes initial movement characteristics of P-wave. The P-wave which diffracts and propagates at a crack tip has a characteristic that its phase may reverse according to the positional relationship between vibration transmitting and receiving points. This positional relationship is decided by the Poisson ratio of media alone. Therefore, when the P-wave is measured while the vibration transmitting and receiving points are moved sandwiching a crack, the polarity of received waveform is changed from negative to positive at a certain position as a boundary. In order to measure this change at high accuracy, an elastic wave of high frequency is required, but it is not easy to obtain the wave in situ. In contrast, utilizing the initial movement polarity can not only identify the change in the polarity, but also perform measurement at high accuracy. The present study discussed a case where cracks are parallel with a free surface and a case where the cracks have angles with the free surface, whereas it was shown that positions of the upper and lower tips of a crack, and length of the crack can be measured accurately. 4 refs., 5 figs.

  11. Point-to-point microwave power transmission experiment; Maikuroha ni yoru denryoku yuso no kiso kenkyu

    Shimokura, N.; Kirihara, T. [Kansai Electric Power Co. Inc., Osaka (Japan)


    In order to demonstrate the power transmission using microwave and arrange advantages and problems in the wireless power transmission, field tests of point-to-point power transmission were conducted. Microwave frequency of 2.45 GHz was used, which is assigned as the industrial, scientific and medical frequency. The transmission system is composed of generator, director tube, primary radiator, and transmission antenna. The maximum 5 kW of microwave power can be transmitted by combining a 3 m-diameter parabolic antenna and a magnetron. The receiving system is composed of devices called as RECTENNA (rectifying antenna). A large capacity and high efficiency RECTENNA was developed, by which the maximum 2.5 W of input power per single device can be provided. As a result of the experiments, efficiency at the transmission side was over 70%, and RF-DC efficiency at the receiving side was about 51%. At the open-air test site, however, the total efficiency of only 14.8% could be obtained. 8 refs., 12 figs.

  12. Energy transmission using microwaves and its possibility. Maikuroha ni yoru energy yuso to sono kanosei

    Matsumoto, H.; Shinohara, N. (Kyoto University, Kyoto (Japan))


    Transmitting of electric energy in the form of electromagnetic waves is a century-old idea, which has reached its final step of realization at last. This paper describes a review and future prospects on electric power transmitting technologies using microwaves (a wavelength of 12 cm is thought as the most promising candidate). Electric power was transmitted successfully to a flying helicopter in the U.S.A. in 1964. Transmission of 30-kW power was performed in 1975 to a power receiving rectenna (an antenna with microwave receiving rectification circuit) placed 1.6 tm away using a parabola as a transmitting antenna. These studies were carried over to the investigative studies on space power stations (SPS). This is a conception to install a static satellite equipped with a huge solar cell array in the sky of about 36,000 km high to generate power, convert the power to microwaves, and transmit the power of ten million kilowatt class to the ground. A number of results of advanced experiments have been obtained in Japan using rockets or aircraft. 26 refs., 5 figs.

  13. Depolymerization of coal by oxidation and alkylation; Sanka bunkai to alkyl ka ni yoru sekitan kaijugo

    Tomita, H.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology


    Change in depolymerization degree and coal structure was studied for depolymerization treatment of coal in various alcohol containing aqueous hydrogen peroxide. In experiment, the mixture of Yallourn coal, alcohol and aqueous hydrogen peroxide was agitated in nitrogen atmosphere of normal pressure at 70{degree}C for 12 hours. As the experimental result, the methanol solubility of only 5% of raw coal increased up to 35.2% by hydrogen peroxide treatment, while the yield of insoluble matters also decreased from 94% to 62%. Most of the gas produced during treatment was composed of inorganic gases such as CO and CO2, and its carbon loss was extremely decreased by adding alcohol. From the analytical result of carbon loss in hydrogen peroxide treatment, it was clarified that alkylation advances with introduction of alkyl group derived from alcohol into coal by hydrogen peroxide treatment under a coexistence of alcohol, and depolymerization reaction of coal itself is thus promoted by alcohol. 4 refs., 7 figs., 1 tab.

  14. Development of plastic pulley by injection molding; Shashutsu keisei ni yoru jushi pulley no kaihatsu

    Yoshizumi, F; Funatsu, A; Yazawa, H [Sumitomo Bakelite Co. Ltd., Tokyo (Japan)


    We developed plastic pulley for automobile manufactured by injection molding which will reduce manufacturing cost. We have developed product design, injection molding technology especially to improve mechanical strength and phenolic molding compound with good wear resistance and high mechanical strength. We have established `Injection Compression molding` technology to improve mechanical strength of weld portion. We also developed phenolic molding compound which is composed of one step resin and long organic fiber to obtain good wear resistance and high mechanical strength. Manufacturing cost will be reduced by using injection molding combined with lower material cost of the newly developed compound. 12 figs., 2 tabs.

  15. Fault structure analysis by means of large deformation simulator; Daihenkei simulator ni yoru danso kozo kaiseki

    Murakami, Y.; Shi, B. [Geological Survey of Japan, Tsukuba (Japan); Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering


    Large deformation of the crust is generated by relatively large displacement of the mediums on both sides along a fault. In the conventional finite element method, faults are dealt with by special elements which are called joint elements, but joint elements, elements microscopic in width, generate numerical instability if large shear displacement is given. Therefore, by introducing the master slave (MO) method used for contact analysis in the metal processing field, developed was a large deformation simulator for analyzing diastrophism including large displacement along the fault. Analysis examples were shown in case the upper basement and lower basement were relatively dislocated with the fault as a boundary. The bottom surface and right end boundary of the lower basement are fixed boundaries. The left end boundary of the lower basement is fixed, and to the left end boundary of the upper basement, the horizontal speed, 3{times}10{sup -7}m/s, was given. In accordance with the horizontal movement of the upper basement, the boundary surface largely deformed. Stress is almost at right angles at the boundary surface. As to the analysis of faults by the MO method, it has been used for a single simple fault, but should be spread to lots of faults in the future. 13 refs., 2 figs.

  16. Weight reduction of automobile parts using light metals. Keikinzoku shiyo ni yoru jidosha buhin no keiryoka

    Hayashi, S [Toyota Motor Corp., Aichi (Japan)


    Weight reduction of automobiles is required from the viewpoint of reduction of CO2 emission and energy conservation. Comparing a car with another one of almost the same size and performance with 1% reduced weight, combustion efficiency of the latter can be improved by 0.5-0.8%. This report introduces several examples, in which steel parts are replaced with light alloy parts to reduce car weight, and describes the future perspective. Concerning a cylinder block which is the heaviest part among engine parts, a block made of aluminum alloy with no cast liner has been developed. There is also an example of an oil pan adopting aluminum die-cast for a part of it. A valve lifter made of aluminum alloy has been developed for valve system parts and has contributed to friction loss, noise reduction, and improvement of fuel consumption. As for steering system parts, a steering bracket made of Mg alloy die-cast has been developed. The use of light alloy parts, in general, increases material cost. Therefore it is now required to build up closer connection between designs and production techniques and to improve reliability of casting and forging technologies. 5 refs., 20 figs.

  17. Biomodification of edible fats and oils by yeasts; Kobo ni yoru shokuyo yushi no seibutsugakuteki kaishitsu

    Fujimoto, K.; Endo, Y. [Tohoku University, Sendai (Japan). Faculty of Agriculture


    Lipid-biomodification ability was examined for yeasts isolated from soil using culture medium containing beef tallow (2%). Some yeasts, e.g. Candida, Trichosporon and Rhodotorula species were able to grow on fats and oils. Fatty acid and triacylglycerol compositions were modified in lipids of some strains. Candida sp. MIS-1 and YM1-1 preferentially produced oleic acid. Candida sp. MIS-1 had high level of triacylglycerol with a melting point like olive oil. Fatty acid composition of lipids in Candida lipolytica IAM4948 and Rhodotorula sp. AO3-5 was similar to that of cacao butter. Yeast oils obtained from C. lipolytica provided the melting characterization different from beef tallow. 30 refs., 3 figs., 7 tabs.

  18. Continuous gravity monitoring of geothermal activity; Renzoku juryoku sokutei ni yoru chinetsu katsudo no monitoring

    Sugihara, M [Geological Survey of Japan, Tsukuba (Japan)


    To clarify the geothermal activity in the geothermal fields in New Zealand, gravity monitoring was conducted using SCINTREX automatic gravimeter. The measurements were conducted between the end of January and the beginning of March, 1996. Firstly, continuous monitoring was conducted at the standard point for about ten days, and the tidal components were estimated from the records. After that, continuous monitoring was conducted at Waimangu area for several days. Continuous monitoring was repeated at the standard point, again. At the Waimangu area, three times of changes in the pulse-shape amplitude of 0.01 mgal having a width of several hours were observed. For the SCINTREX gravimeter, the inclination of gravimeter is also recorded in addition to the change of gravity. During the monitoring, the gravimeter was also inclined with the changes of gravity. This inclination was useful not only for the correction of gravity measured, but also for evaluating the ground fluctuation due to the underground pressure source. It is likely that the continuous gravity monitoring is the relatively conventional technique which is effective for prospecting the change of geothermal reservoir. 2 figs.

  19. Three dimensional wavefield modeling using the pseudospectral method; Pseudospectral ho ni yoru sanjigen hadoba modeling

    Sato, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center


    Discussed in this report is a wavefield simulation in the 3-dimensional seismic survey. With the level of the object of exploration growing deeper and the object more complicated in structure, the survey method is now turning 3-dimensional. There are several modelling methods for numerical calculation of 3-dimensional wavefields, such as the difference method, pseudospectral method, and the like, all of which demand an exorbitantly large memory and long calculation time, and are costly. Such methods have of late become feasible, however, thanks to the advent of the parallel computer. As compared with the difference method, the pseudospectral method requires a smaller computer memory and shorter computation time, and is more flexible in accepting models. It outputs the result in fullwave just like the difference method, and does not cause wavefield numerical variance. As the computation platform, the parallel computer nCUBE-2S is used. The object domain is divided into the number of the processors, and each of the processors takes care only of its share so that parallel computation as a whole may realize a very high-speed computation. By the use of the pseudospectral method, a 3-dimensional simulation is completed within a tolerable computation time length. 7 refs., 3 figs., 1 tab.

  20. Groundwater exploration by self-potential method; Shizen den`iho ni yoru chikasui tansa

    Onaru, I; Irie, S; Mizunaga, H; Ushijima, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    This paper describes results measured from the field experiments and data analysis of the groundwater exploration by self-potential method. The field survey was conducted in the vicinity of spring water source in the suburbs of Fukuoka City. For the field experiments, potential differences from the standard potential electrode set at the distance about 200 m were measured at multi-points, simultaneously. For the laboratory experiments, assuming that the groundwater flows in a permeable layer, streaming potential change was observed against the changes of flow rate and electrical conductivity. Thus, the generation of streaming potential was investigated. For the experiment using specimens obtained at the spring water source, the potential changed to negative and was stabilized in around -80 mV after 15 minutes. Numerical simulation was conducted by means of the three-dimensional finite difference method using parameters obtained from the laboratory experiments. From these results, the groundwater flow image could be obtained. It was also confirmed that the self-potential observed in the spring water source area was caused by the streaming potential. 11 refs., 9 figs.

  1. 3D pre-stack time migration; Kiruhihoffuho ni yoru sanjigen jugo mae jikan migration shori

    Nakajima, Y; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsuru, T [Japan National Oil Corp., Tokyo (Japan)


    This paper reports pre-stack migration in elastic wave exploration as to its algorithm and examples of processed data. The time migration processing hypothesizes that seismic waves propagate linearly. It calculates travel time by dividing the sum of the straight distance from a vibration transmitting point to an image point and the straight distance from the image point to a vibration receiving point with RMS velocity given as a parameter. To maintain the relative relation of amplitude sizes, the signal on an elliptic body is made smaller in inverse proportion to the size of that elliptic body. With regard to apparent interval of input trace as seen from the reflection surface, or with regard to density, the signal is made smaller by cos{theta} times. While this program deals with three-dimensional migration, its output turns out as an arbitrary two-dimensional plane. The program requires a huge amount of data processing, whereas a method is used, that the input trace is divided, each group is processed by using separate computers, and the results are summed up. 3 refs., 4 figs.

  2. Countermeasures for increasing sequence continuous casting; Renchu kinosei taikabutsu zaishitsu, kozo kaizen ni yoru renrenchusu kojosaku

    Tsuda, Masato; Shinagawa, Hiroaki; Kamada, Ryuji; Hiraga, Yutaka; Hara, Takayasu [Nippon Steel Corp., Tokyo (Japan)


    In the second continuous casting line of Kure Iron Works, Nisshin Steel Co., Ltd. improvement of the continuous casting counts per tundish was attempted for a target of max. 20. The results are as follows: (1) Non-SiO{sub 2} conversion of material for the long nozzle immersed part: About 20% improvement of durability compared with a conventional material to clear 0.059 mm/min of the targeted erosion speed when 20 CCC/TD is realized, (2) Durability improvement of SN plate: About 20% durability improvement was attained compared with a conventional material by the adoption of a non-SiO{sub 2} material, (3) Erosion resistance improvement of the immersed nozzle slug line part: Castable period was extended to 1 ch life improvement by increasing zirconia content, (4) Rise of stopper full open position: The rise of the full open position produced less variation of melt level than the conventional structure without increase of the SN opening, enabling plugging prevention between the stopper head and the upper nozzle which was an objective of this improvement, (5) Structure improvement of the upper nozzle: This improvement successfully prevented leaks from damage of the casting stop nozzle metal case and enabled casting under low gas flow even in TD nozzle plugging. These improvements gave a possibility to achieve max. 20 CCC/TD. (NEDO)

  3. Regeneration of furfural on activated carbon with methanol; Furufuraru kyuchakutan no metanoru ni yoru saisei

    Sudo, Y. [Tokyo National College of Technology, Tokyo (Japan); Suzuki, M. [Tokyo Univ. (Japan). Inst. of Industrial Science


    Experiments of regenerating solvent from activated carbon are performed using furfural (1-phenyl-2-propane) as the absorbent and methanol as the solvent for regeneration. In 5 repeated adsorption-desorption cycles, the solvent becomes in dynamic stationary state after the second cycle with about 10% not desorption yet, and it is found that considerable number of repetition of furfural adsorbed carbon regeneration is possible by the use of methanol. The overall mass transfer coefficient of furfural and methanol in desorption is calculated. In addition, an experiment is carried out changing the adsorption ratio of furfural and the flow velocity of methanol to investigate desorption mechanism of furfural adsorbed carbon. Larger difference of adsorption equilibrium of furfural in aqueous solution and in methanol is efficient in desorption of furfural adsorbed carbon by methanol, but it is found that desorption rate is affected by mixed diffusion in the column and the surface diffusion is dominant in particles. 17 refs., 10 figs.

  4. High power YAG laser cutting; Koshutsuryoku YAG laser ni yoru setsudan gijutsu

    Owaki, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)


    This paper describes features of high power YAG cutting. The optical fiber transmission YAG laser machining system has some advantages in which optical path length compensation unit is not required and measures for low power loss and dust are not required, when compared with the CO2 laser system. Its application to the cutting of stainless steel plates has attracted attention. Cutting tests of SUS304 were conducted using high power YAG laser. Cutting of SUS304 plate with a thickness of 40 mm could be successfully done at the power of 3.5 kW. Cutting tests of SUS304 pipes with a thickness of 8 mm in water under the depth of 20 m were also conducted using air as assist gas at the power of 2.5 kW. Excellent results were obtained without scale deposition. For the tests by the composite beam using 3 kW and 4 kW systems, SUS304 plate with a thickness of 50 mm could be cut at the cutting speed of 0.1 m/min. Laser cutting of pipes from the internal surface was conducted using a newly developed small machining head which can rotate in the peripheral direction. Excellent quality for welding was confirmed. Cutting speed and plate thickness were improved by combining water jet cutter and YAG laser unit. 6 refs., 10 figs.

  5. Car audio using DSP for active sound control. DSP ni yoru active seigyo wo mochiita audio

    Yamada, K.; Asano, S.; Furukawa, N. (Mitsubishi Motor Corp., Tokyo (Japan))


    In the automobile cabin, there are some unique problems which spoil the quality of sound reproduction from audio equipment, such as the narrow space and/or the background noise. The audio signal processing by using DSP (digital signal processor) makes enable a solution to these problems. A car audio with a high amenity has been successfully made by the active sound control using DSP. The DSP consists of an adder, coefficient multiplier, delay unit, and connections. For the actual processing by DSP, are used functions, such as sound field correction, response and processing of noises during driving, surround reproduction, graphic equalizer processing, etc. High effectiveness of the method was confirmed through the actual driving evaluation test. The present paper describes the actual method of sound control technology using DSP. Especially, the dynamic processing of the noise during driving is discussed in detail. 1 ref., 12 figs., 1 tab.

  6. Environmental pollution by dioxin and its biodegradation; Dioxin ni yoru kankyo osen to sono biseibutsu bunkai

    Nojiri, H.; Yamane, H.; Omori, T. [Tokyo Univ. (Japan)


    Polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and coplanar polychlorinated biphenyls (Co-PCBs) exhibit similar chemical and biological properties. Because of their highly toxic activity, the pollution with these compounds, which are called dioxin-related compounds, is one of the most serious environmental problems. In this review, we described the analytical methods of dioxin-related compounds in environmental samples, especially in the exhaust gas from the incineration site of municipal solid waste. In addition, we described the present situation of environmental pollution by dioxin-related compounds, including pollution levels in environmental, human, and food samples, daily intakes, and risk assessment. On the other hand, a number of microorganisms have been reported which are able to degrade dioxin-related compounds including PCDDs and PCDFs. These microorganisms are classified into two groups, lignin-degrading white rot fungi and the dioxin-degrading bacteria. We also described the degradation pathways of dioxin-related compounds in these microorganisms, and their degradative enzymes. 47 refs., 5 figs., 4 tabs.

  7. Catalyst surface characterized by high magnetic field NMR; Kojiba NMR ni yoru shokubai hyomen no kansatsu

    Sato, S. [Chiba University, Chiba (Japan). Faculty of Engineering


    This paper introduces studies performed by the authors on observation of surface of solid catalysts by means of solid NMR measurement using the high-speed MAS technology which uses a high magnetic field device. In the studies, a device with 14.1T (resonant frequency of proton at 600 MHz) was used to conduct CP-MAS NMR measurement on {sup 29}Si to identify bonding of silica carrier in a fixed aluminum chloride catalyst. As a result, it was verified that the surface structure of aluminum chloride species deposited on the silica carrier turns to a structure in which AlCl2 species of a monomeric substance is bonded with a surface hydroxyl group and fixed in four- or five-orientation. When adjusted at low temperatures, an Al2Cl5 structure is formed, which is fixed as a dimeric substance with AlCl3 oriented in the AlCl2 species. It is conceived that the Al2Cl5 species has higher electrophilicity than the AlCl2 species as a result of AlCl3 oriented in AlCl2, whereas the hydroxyl group on the silica surface oriented with the Al2Cl5 species dissociates, discharging protons, thus showing strong acidity. 18 refs., 8 figs., 2 tabs.

  8. CVT control and vehicle acceleration; CVT hensoku ni yoru shasoku otosei

    Takiyama, T; Morita, S [Osaka City University, Osaka (Japan)


    For the drivetrain control, it becomes important for fuel economy or AHS to control the throttle valve of the engine and the gear ratio of CVT simultaneously by DBW when CVT is equipped with the automobile. In this paper, LQI control theory was applied to control the drivetrain as 2-I/O system to satisfy the commanded speed and better fuel economy. And modification of the weight parameter of LQI was investigated to obtain the desired performance for fuel economy or vehicle acceleration. Relatively good expected results were obtained. 5 refs., 7 figs., 1 tab.

  9. Treatment of hexavalent chrome by bacteria. Saikin ni yoru rokka kuromu no shori

    Otake, H [Hiroshima University, Hiroshima (Japan). Faculty of Engineering


    A biological reduction method in which hazardous hexavalent chrome is reduced by bacteria is explained as one of the bioremediation technologies. Those bacteria are separated from active sludge in the urban sewage treatment plant. The hexavalent chrome-reducing bacteria were isolated by cultivating the sludge. They were Enterobacter cloacae which are intestinal bacteria. Then, they were named HO1 stock. As a result of analyzing the reduction mechanism, it was made clear that the function is localized in the cellular endosporium and that the reduction is made by utilizing the electronic transfer system of endosporium. Under both aerobic and anaerobic conditions, they convert the hexavalent chrome into the trivalent chrome outside the cells. As a result of test, it was known that 5mM hexavalent chrome can be treated in one day. A quick reduction was confirmed also through an experiment in which carbon source was added to the industrial wastewater. If used for the treatment of sludge/water contaminated by hexavalent chrome, the present reduction by bacteria has the following advantages: The highest reduction rate is given near pH=7 at ordinary temperatures. It is not necessary to add chemicals. Energy is not needed. It is a disadvantageous fact that the present bacteria, if exposed to oxygen, become inactive. 18 refs., 5 figs.

  10. FY1995 community support by mobile agents; 1995 nendo mobile agent ni yoru community keisei shien



    The purpose is to develop fundamental technologies for navigation systems and mobile computing systems in museums, theme parks and cities. Concretely, we implement software agents into the mobile computing environment which consists of PHS, mobile computers and mobile robots, and realize various functions to access regional information. We have studied on Communityware which supports human activities and communities by using mobile agents implemented into mobile computers and town robots. The mobile agents, which intelligently process information obtained in physical and virtual worlds, access regional information which is omnipresent in the environment. With respect to the approach using mobile computers, we have provided one hundred mobile computers in the international conference on multiagent systems 1996 and carried out the first experimentation of mobile computing in the world. The mobile computer has two functions: Community Viewer which displays interactions between members of communities and Social Matchmaker which supports to hold meetings by searching for people who have common interests. With respect to the approach using town robots, we have developed a robot system which can robustly behave in a complex outdoor environment by using vision agents embedded in the environment. The system aims at support of people in streets. (NEDO)

  11. Fixation of carbon dioxide by coral reef. Sangosho ni yoru CO2 no kotei

    Yamamuro, M [Geological Survey of Japan, Tsukuba, Ibaraki (Japan)


    The methods for fixation of carbon dioxide in the atmosphere in order to control the greenhouse effect, are groped. Carbon is fixed through two ways such as the production of organic compounds by photosynthesis and formation of calcium carbonate by calcification. Among them, the photosynthesis fixes carbon dioxide in the air, and calcification, on thinking of only chemical equilibrium in the sea water, is a process to exhaust carbon dioxide from ocean to the atmosphere. It is, therefore, uneven in opinions of researchers if the coral reef is an absorbing source or an exhausting one of carbon dioxide. A conventional discussion on this theme, did not carry out based on the actual search or measurement, but preceded on modelling. In order, therefore, to introduce a scientific decision on a play of the coral reef for the global carbon circulation, it seems to take more time. In this paper, an opinion that the coral reef is an absorbing source of carbon dioxide in the air according to some measuring results of carbon dioxide fixation velocity and organic compounds volume in sediments in the coral reefs, are described. 11 refs., 4 figs.

  12. CO2 fixation by coral reefs. Sangosho ni yoru nisanka tanso no kotei

    Kayane, H [Geological Survey of Japan, Tsukuba (Japan)


    In order for a coral reef to be a CO2 absorbing source, a condition would have to be satisfied that, with respect to production of organic carbon through photosynthesis, a total production by coral reef organism association is large, and the ratio of the total production to a total consumption is more than one. A requirement that the ratio of inorganic carbon production through calcification be 1.5 or more must also be met. Measurements have been carried out at coral fields off the Ishigaki Island by the Geological Research Center. The measurement results revealed that production is high for both of organic carbon and inorganic carbon, surplus organic carbon is produced, and CO2 is absorbed into the coral reefs. It was also found by measuring the stable isotope ratio of nitrogen in coral reef organisms that nitrogen required for the production in the coral reefs is supplied from the atmosphere through nitrogen fixation. The paper adds a description that CaCO3 deposition in the coral reefs has peaked in 5000 years to 6000 years ago, and it is in a ceiling-hit condition now. 25 refs., 3 figs.

  13. Biological fixation of carbon dioxide. Seibutsu ni yoru nisanka tanso no kotei

    Someya, J [Fermentaion Research Institute, Tsukuba (Japan)


    Bulks of photosynthetic product to reduce the carbon dioxide by the light energy are forests, represented by the tropical rain forests, on the land, and marine algae and coral reefs in the ocean. For the purpose of effectively utilizing the fixation power of carbon dioxide through the photosynthesis by higher plants and algae, it is necessary to make many further researches, starting with a conditional selection of species, excellent in both absorption and fixation of carbon dioxide. The Japan Technology Transfer Association has recently issued a design to build a large scale closed type farm in the vicinity of factory, exhausting the carbon dioxide, and supply it to structure a system of producing vegetable and other food. What largely contributes to the calcification in the ocean is the coral reefs, where coral is symbiotic with brown algae., called dinoflagellatae. Those algae are judged to accelerate the formation of calcium carbonate by the photosynthesis. To estimate the absorption power of oceanic carbon dioxide, it is important to quantitatively know the calcification by the coral. 4 figs., 1 tab.

  14. Coral reefs as fixers of CO2. Sangosho ni yoru nisanka tanso no kotei

    Yamamuro, M [Geological Survey of Japan, Tsukuba (Japan)


    This paper explains CO2 fixing mechanisms in coral reefs and technologies to construct coral reef eco-factories. A coral reef fists CO2 through two routes of photosynthesis and calcification, with both processes proceeding conjugately. Calcification is driven by the photosynthesis that proceeds at a rate more than ten times faster than the calcification. The Geological Survey of Japan is working on elucidating CO2 fixing mechanisms in coral reefs and studying coral reef eco-factory structuring technologies to utilize the capability of the mechanisms at a possible maximum extent. This study is directed to optimizing site conditions for coral reefs, optimal arrangements and environmental conditions for clusters, and production process determining factors. The structuring technologies may include controlling water temperatures, water flows, nutritious salts, and suspended substances that match optimal CO2 fixing conditions in coral reefs; seeding technologies for coral reef organisms; aquaculture techniques utilizing fixed CO2; combination with cultivating techniques; and combination with new energy technologies including sea water temperature difference power generation to control water flows and maintain facilities. 4 refs., 5 figs.

  15. Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa



    The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

  16. Chlorofluorocarbons (CFCs) destruction technology by induction coupled plasma; Koshuha purazuma ni yoru tokutei furon hakai gijutsu ni tsuite

    Kobayashi, A. [Nippon Steel Corp., Tokyo (Japan)


    Abolishing flon in which the reuse by pollution and degradation is difficult by recovery flon and recovery and recycling process which do not rotate for the middle reuse that the recovery system is constructed is arising. And, the specific flon recovery quantity increases with the progress of development of the recent CFC substitute and renewal to the CFC substitute correspondence machine. Specific flon collapse technique using rf plasma introduced in this paper cultivated the basic technology in Agency of Industrial Science and Technology, resources environment integrated research place. The demonstrated operation research was carried out under Ministry of International Trade and Industry, New Energy and Industrial Technology Development Organization since December 1994. (NEDO)

  17. High-accuracy measurement of ship velocities by DGPS; DGPS ni yoru sensoku keisoku no koseidoka ni tsuite

    Yamaguchi, S; Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics


    The differential global positioning system (DGPS) can eliminate most of errors in ship velocity measurement by GPS positioning alone. Through two rounds of marine observations by towing an observation robot in summer 1995, the authors attempted high-accuracy measurement of ship velocities by DGPS, and also carried out both positioning by GPS alone and measurement using the bottom track of ADCP (acoustic Doppler current profiler). In this paper, the results obtained by these measurement methods were examined through comparison among them, and the accuracy of the measured ship velocities was considered. In DGPS measurement, both translocation method and interference positioning method were used. ADCP mounted on the observation robot allowed measurement of the velocity of current meter itself by its bottom track in shallow sea areas less than 350m. As the result of these marine observations, it was confirmed that the accuracy equivalent to that of direct measurement by bottom track is possible to be obtained by DGPS. 3 refs., 5 figs., 1 tab.

  18. Research on crystal growth by using pressure as a control parameter; Atsuryoku seigyo ni yoru kessho seicho ni kansuru kenkyu



    This research project aims to establish a technique for crystal growth using pressure as a principal control parameter, and combining it with a microgravity condition, to develop a novel process material fabrication. Since the solubility of materials depends on pressure, it is possible to control a supersaturated condition for crystal growth by changing pressure. The growth condition can be controlled precisely, which is not possible by conventional methods that vary temperature and other factors. On the other hand, because a concentration diffusing field is formed autonomically around crystals in association with their growth, density convection is generated under gravity as a result of difference in the concentrations, making the growth conditions severely complex and uncontrollable. Ideal crystal growth condition control may be possible if the pressure control is performed under micro-gravity by which generation of the density convection can be suppressed. Realization has been achieved on in-situ observation by using high-magnification microscope which uses a diamond anvil cell, development of a hydraulic type optic pressure cell, and a high- speed crystal growing technology by means of pressure control utilizing the cell. New findings were also obtained on effects of pressure on crystal forms, and the pressure induced solid phase transfer mechanism. 67 refs., 49 figs., 3 tabs.

  19. Test results of cultivation of vegetables with fish breeding water; Yogyosui riyo ni yoru yasai saibai shiken kekka ni tsuite

    Nishida, S. [Hokuriku Electric Power Co. Inc., Toyama (Japan)


    Entrails of fish, fowls and domestic animals are mostly incinerated at large expenses, although partly used as foods. This study is to test `possibility of vegetable cultivation with fish breeding water,` where the entrail wastes are used as baits for fish breeding, and fish excretions are used as the fertilizer for vegetable cultivation to purify water for fish breeding. The cultivation bed consists of two sections, one for fish breeding/vegetable cultivation and the other for vegetable cultivation by the normal method. Vegetable grow notably less in the former than in the latter, 54.6 to 79.5 versus 100. Spinach contains slightly higher contents of vitamins A and C by 6 and 13%, when cultivated in the former than in the latter. Quantities of total nitrogen, phosphorus and potassium as the fertilizer components in the former are 49, 49 and 1.7% of those in the latter. It is predicted, judging from growth of the vegetables, that the former gives a harvest comparable with that by the latter, when given a 6 to 13 days longer cultivation period. 3 figs., 2 tabs.

  20. Test results on vegetable cultivation using fish breeding water; Yogyosui riyo ni yoru yasai saibai shikenkekka ni tsuite

    Nishida, S. [Hokuriku Electric Power Co. Inc., Toyama (Japan)


    Although a part of the entrails of fishes, birds and livestock is used for food, most of them are treated by costly combustion because of their bad odor and looking, and International Environment and Welfare Laboratory, Toyama prefecture in Japan is studying their profitable treatment. As a part of such study, possibility of hydroponic cultivation of vegetable was tested using fish breeding water including excretions of fishes and residual feeds after use of waste as feed, and the growth condition, safety and effectiveness of cultured vegetable were verified. Three-hundred and fifty viviparous Oryzias were released into a breeding water area with no controlled pH and EC (electric conductivity). For comparison a culture solution area of 6.0 in pH and 1.2ms/cm in EC was prepared. The result on cultivation of 6 kinds of vegetable in culture beds supported by circulation of these water showed that hydroponic cultivation of vegetable using fish breeding water is possible, and average growth of 68% is obtained although difference in growth for every vegetable is found. 8 figs., 5 tabs.

  1. Flat plate approximation in the three-dimensional slamming; Heiban kinji ni yoru sanjigen suimen shogeki keisanho ni tsuite

    Toyama, Y. [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)


    A slamming load generated by interactive motions between a ship body and water face is an important load in ensuring safety of the ship. A flat plate approximation developed by Wagner is used as a two-dimensional slamming theory, but it has a drawback in handling edges of a flat plate. Therefore, an attempt was made to expand the two-dimensional Wagner`s theory to three dimensions. This paper first shows a method to calculate water face slamming of an arbitrary axisymmetric body by using circular plate approximation. The paper then proposes a method to calculate slamming pressure distribution and slamming force for the case when shape of the water contacting surface may be approximated by an elliptic shape. Expansion to the three dimensions made clear to some extent the characteristics of the three-dimensional slamming. In the case of two dimensions or a circular column for example, the water contacting area increases rapidly in the initial stage generating large slamming force. However, in the case of three dimensions, since the water contacting area expands longitudinally and laterally, the slamming force tends to increase gradually. Maximum slamming pressure was found proportional to square of moving velocity in a water contacting boundary in the case of three dimensions, and similar to stagnation pressure on a gliding plate. 12 refs., 17 figs., 1 tab.

  2. Consideration on local blast vibration control by delay blasting; Danpatsu happa ni yoru kyokuchiteki shindo seigyo ni kansuru ichikosatsu

    Mogi, Gento; Adachi, Tsuyoshi; Yamatomi, Jiro [The University of Tokyo School of Engineering Department of Geosystem Engineering, Tokyo (Japan); Hoshino, Tatsuya [Mitsui Mining and Smelting Corp., Tokyo (Japan)


    In this research, local blast vibration control based on the theory of superposition of waves was investigated. Firstly, the influence of delay time errors of conventional electric detonators upon the level of local blast vibration was examined. Secondly, for a further effective local blast vibration control, a new delay blasting design concept 'combined delay blasting' that postulates the use of electronic detonators, which virtually have no delay time errors, is proposed. For a delay blasting with uniform detonation time intervals, an optimum time interval to minimize the local PPV (Peak Particle Velocity) is obtained based on the relationship between the PPV and the time interval, which is derived by superposing identical vibration time histories of each single hole shot. However, due to the scattering of the actual delay time caused by errors, PPV of a production blast seldom coincides with the estimated one. Since the expected value and the variance of PPV mainly depend on sensitivity of PPV around the nominal delay time, it is proposed that not only the optimum but also several sub-optimum candidates of delay time should be examined taking error into consideration. Concerning the 'combined delay blasting', its concept and some simulation results are presented. The estimated reduction effect of blast vibration of a delay blast based on this concept was quite favorable, indicating a possibility for further effective local blast vibration control. (author)

  3. Flat plate approximation in the three-dimensional slamming; Heiban kinji ni yoru sanjigen suimen shogeki keisanho ni tsuite

    Toyama, Y [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)


    A slamming load generated by interactive motions between a ship body and water face is an important load in ensuring safety of the ship. A flat plate approximation developed by Wagner is used as a two-dimensional slamming theory, but it has a drawback in handling edges of a flat plate. Therefore, an attempt was made to expand the two-dimensional Wagner`s theory to three dimensions. This paper first shows a method to calculate water face slamming of an arbitrary axisymmetric body by using circular plate approximation. The paper then proposes a method to calculate slamming pressure distribution and slamming force for the case when shape of the water contacting surface may be approximated by an elliptic shape. Expansion to the three dimensions made clear to some extent the characteristics of the three-dimensional slamming. In the case of two dimensions or a circular column for example, the water contacting area increases rapidly in the initial stage generating large slamming force. However, in the case of three dimensions, since the water contacting area expands longitudinally and laterally, the slamming force tends to increase gradually. Maximum slamming pressure was found proportional to square of moving velocity in a water contacting boundary in the case of three dimensions, and similar to stagnation pressure on a gliding plate. 12 refs., 17 figs., 1 tab.

  4. Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

    Suzuki, H; Seo, K; Yamanaka, H [Tokyo Institute of Technology, Tokyo (Japan)


    The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

  5. Estimation of Rayleigh-wave spectral ratio from microtremors using a three-component single-station seismograph; Itten sanseibun bido kansoku ni motozuita Rayleigh ha shinpukuhi no suitei

    Yamamoto, H; Mizutani, K; Saito, t [Iwate University, Iwate (Japan). Faculty of Engineering


    Discussions were given on the possibility of estimating Rayleigh-wave spectral ratio utilizing phase difference between horizontal movements and vertical movements by using a three-component single-station seismograph. The test has selected as an observation point a location in the city of Kushiro where a pulp and paper mill generating microtremors is the focal point, and the underground structure at that point has been estimated by using the vertical array observation method. The observation system has used three components of a velocity type seismograph having a natural period of one second, an amplifier and an analog data recorder. As a result of the discussions, the following matters were made clear: the spectral ratio with a phase difference of 90 degrees agrees with the frequency at a peak trough of the theoretical Rayleigh-wave spectral ratio; the values of the spectral ratio at the phase difference of 90 degrees and the values of the theoretical Rayleigh-wave spectral ratio correspond well excepting in frequency bands of the peak trough; and these results suggest that the Rayleigh-wave spectral ratio may be estimated by utilizing the phase difference between horizontal movements and vertical movements. Estimation of the underground structure by using the inverse analysis of this Rayleigh-wave spectral ratio is expected in the future. 6 refs., 5 figs., tab.

  6. Measurement of Activity Coefficients of Solvents in Poly ( ethylene oxide ) Using Gas-Chromatographic Method and Correlation by Polymer-ASOG; Poriechirenokishido chu no yobai katsuryo keisu no gasukuromatogurafu ho ni yoru sokutei to Polymer-ASOG ni yoru sokan

    Tochigi, K.; Kurita, S.; Ohashi, M. [Yuki Gosei Kogyo Co. LTd., (Japan); Kojima, K. [Nihon University, Tokyo (Japan). Department of Industrial Chemistry


    Infinite dilution activity coefficients (353.15-393.15 K) of six solvents (benzene, toluene, p-xylene, cyclohexane, acetone and methylethylketone) and activity coefficient at finite concentrations (353.15 K, 373.15 K) of these solvents in poly (ethylene oxide) are measured using gas-chromatographic method. The experimental data are then correlated by a polymer-ASOG model. 18 refs., 2 figs., 3 tabs.

  7. Distribution of strong ground motion from uppermost crustal structure. Comparison with disaster from the Hyogo-ken Nanbu Earthquake; Yaya fukai chika kozo no henka ni yoru kyoshindo bunpu. Hyogoken nanbu jishin ni yoru higai bunpu tono hikaku

    Zhao, Z; Okubo, R [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan)


    It was intended to elucidate characteristics of distribution of damages caused by an earthquake which occurs directly below an urban area. Therefore, numerical simulation using the pseudo-spectral method was performed on characteristics of seismic wave propagation in non-homogenous media composed of rock beds and sediment beds, and of seismic wave amplitudes on ground surface. The simulation has utilized information on underground structures disclosed by using the latest physical exploration method. The underground structure model assumed a two-dimensional model hypothesizing presence of upper, middle and lower beds in the Osaka bed group on granite, using as reference the information on S-wave velocity underground structure revealed by the microtremor exploration method. With an objective to elucidate characteristics of distribution of collapse ratio in the area from 8-chome, Okamoto, Higashinada Ward, Kobe City to 2-chome of Sakanasaki Minamicho, as damages suffered from the Hyogo-ken Nanbu Earthquake, a simulation has been performed varying the structure model based on the results derived by the microtremor exploration method and the reflection method. As a result, it was shown that the characteristics of the maximum amplitude distribution of displacement of ground surface, velocity and acceleration agree well with those of the collapse ratio distribution, and that the simulation using the pseudo-spectral method is an effective means to analyze the ground surface collapse ratio distribution. 5 refs., 3 figs.

  8. Surface flaw detection by means of infrared radiometer. Part 3. ; Detection limit influenced by an environment temperature. Sekigai hoshakei ni yoru hyomen kekkan no kenshutsu. 3. ; Shuhen ondo ni yoru kenshutsu genkai no eikyo

    Okamoto, U; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T [Ibaraki University, Ibaraki (Japan); Eto, M; Ooka, N; Kanaya, K; Eto, Y [Japan Atomic Energy Research Institute, Ibaraki (Japan); Kurokawa, T [Nippon Denki Sanei Ltd. Co., Tokyo (Japan)


    Measuring a radiation energy distribution around surface flaw by means of a infrared rediometer can detect fine flaw on the surface. The characteristics were examined using a light quantum type radiation thermometer consisted of Hg-Cd-Te as a sensor. A surrounding wall consisted of a black body wall was installed between the sensor and test piece, and by thus maintaining the surrounding wall temperature constant, reflection energy from the test piece surface was maintained constant for stabilized measurement. The measurement values are the sum of energies from emission and reflection, or the so-called radiosity values. To avoid effects from the reflection to reduce variance in the emissivity, it is necessary to keep the surrounding wall temperatures lower by more than 20 {degree}C than the test piece radiation temperatures. Emissivity can be calculated from the rediositivity (sum of the radiation and the reflection), the surrounding wall temperatures, and the test piece radiation temperatures. If the surface is rough, variance in the measurements increases. The larger the difference in the test piece and surrounding wall temperatures, the thermo image of the defects on the test piece surface becomes more distinctive, thus the detection limit can be enhanced. 7 refs., 13 figs.

  9. Wavefield analysis in inhomogeneous media by wavelet transform; Wavelet henkan ni yoru fukinshitsu baitai no hadoba kaiseki

    Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Ichie, Y [The University of Tokyo, Tokyo (Japan)


    Data processing techniques have been investigated for clarifying structures and physical properties of geothermal reservoirs in the deep underground by seismic exploration using multiple wells. They include the initial motion time-distance tomography, amplitude tomography, diffracted wave tomography, and structure imaging using reflected wave or scattered wave. When applying these data processing methods to observed records, weak and minor signals essentially required are canceled due to averaging the analytical fields. In this study, influence of inhomogeneous media on the wavefield was evaluated. Data were analyzed considering frequency by using wavelet transform by which time-frequency can be easily analyzed. From the time-frequency analysis using wavelet transform, it was illustrated that high frequency scattered waves, generated by scatterer like cracks or by irregularity on the reflection surface, arrive behind direct P-wave and direct S-wave. 5 refs., 8 figs.

  10. Causality analysis of alpha activities by multidimensional directed coherence; Tajigen yuko coherence ni yoru {alpha}ritsudo no ingasei kaiseki

    Sakata, O.; Shimada, N.; Shiina, T. [University of Tsukuba, Tsukuba (Japan); Saito, Y.; Imanishi, N.


    Alpha activities as a basic component of EEG (electroencephalogram) are mainly observed with eye-closed and reported state, and indicates rhythmic and diffused pattern on the scalp. Therefore analysis of the relation among many sequences of alpha activities measured at different positions on the scalp is expected to be useful not only for diagnosing psychiatric but also for investigating mechanism of brain information processing by means of causality analysis that is, macroscopic estimation of flow pattern within brain. Although coherence analysis has been proposed as a method for estimating the direction and magnitude of information flow between two sequences, superposition of results for each pair of sequences can not represent true relation among the whole sequences. In this paper, we proposed the multidimensional directed coherence analysis by modifying two-channel formula in order to apply it to the analysis of multi-channel sequence of alpha activities. Results of simulation revealed that multidimensional directed coherence can indicate more quantitatively the relation among the multi-channel sequences compared with conventional two-channel formula. Moreover, the proposed method was applied to the analysis of EEG data of normal volunteer and patient. Results show the method can provide a useful diagnostic information by assessment of the signal flow pattern within brain. 16 refs., 10 figs.

  11. Synthesis of Monodispersed Spherical Single Crystalline Silver Particles by Wet Chemical Process; Shisshiki kagakuho ni yoru tanbunsankyujo tankesshoginryushi no gose

    Ueyama, Ryousuke.; Harada, Masahiro.; Ueyama, Tamotsu.; Harada, Akio. [Daiken Chemistry Industry Corporation, Osaka (Japan); Yamamoto, Takashi. [National Defence Academy, Kanagawa (Japan). Dept. of Electrical Engineering; Shiosaki, Tadashi. [Nara Institute of Science and Technology, Nara (Japan). Graduate School of Materials Science; Kuribayashi, Kiyoshi. [Teikyo University of Science and Technology, Yamanashi (Japan). Dept. of Materials


    Ultrafine silver monodispersed particle were prepared by wet chemical process. To decrease the reduction speed, an important factor in generating monodispersed particles is to control the following three factors: synthesis temperature, concentration of aggregation-relaxing agent added, and concentration of silver nitrate solution. Synthesis of monodispersed spherical Ag particles, used as metal powders for electrode, became possible using the nucleus grouwth reaction method. This process also allowed the control of the diameter of the powder particles. The silver particles were distributed in ta narrow particle diameter range with on average of 0.5 {mu}m. Transmission electron microscopy (TEM) revealed that single-crystalline silver particles were prepared by the present method. (author)

  12. Removal of chemical substances from the atmosphere by photocatalysis; Hikarishokubai ni yoru kiso kagaku busshitsu no jokyo

    Takeuchi, K; Kutsuna, S [National Institute for Resources and Environment, Tsukuba (Japan)


    Suppression at a source is the principle of suppressing air pollution caused by vapor phase chemical substances. For the case of these substances with extremely low concentrations, discussions were given on decomposition by means of photocatalysts (that utilize solar light) to directly purify them in the atmospheric condition. Catalysis takes place in providing and receiving electrons, that is, oxidation and reduction of the electrons, under light irradiation by using photocatalysts in which light excites and causes internal electrons to migrate freely. Titanium oxide was found effective because it is high in catalytic activity, stable chemically, and harmless. Photodecomposition reaction of chlorinated organic compounds on TiO2 proceeds very fast except for fluorocarbons. In practical use, the catalyst must be fixed so that no catalyst powder will scatter around. Porous TiO2 sheets were, therefore, manufactured using fluorine resin as a binder. The sheets were used to have removed successfully NOx, SO2 and low-grade aldehyde with concentrations from 0.01 to 10 ppm (corresponding to gases discharged from a tunnel). Since the catalyst can function even under solar light, it can remove NOx during daytime, and can be regenerated by precipitation (passive environment purification). The catalyst was verified effective when used on roads in urban areas. 16 refs., 9 figs., 3 tabs.

  13. Acetaldehyde formation from ethanol over titanium dioxide photocatalyst. Nisanka titan hikarishokubai ni yoru ethanol kara no acetaldehyde no seisei

    Iseda, K [Government Industrial Research Institute, Nagoya, Nagoya (Japan)


    The suspention of TiO {sub 2} (rutile structure, 99.9%, 300 mesh) photocatalyst in ethanol was irradiated under ultraviolet light in an argon atmosphere at 25 centigrade. Acetaldehyde, methane and hydrogen were detected as products. When the photocatalysis of TiO {sub 2} itself was examined comparing with the result of blank test without using catalyst, the activity of TiO {sub 2} was confirmed only for the formation of acetaldehyde among the products. The yields of acetaldehyde increased with increasing addition of catalyst. The increasing rate of methane yields was rather small and the methane yields were lower than those in the blank tests. The hydrogen yields were almost same as in the blank tests. Acetal was formed in the blank test but was not formed with addition of TiO {sub 2}. It was provided that TiO {sub 2} was an effective catalyst for the formation of acetaldehyde. 6 ref., 5 figs.

  14. Three dimensional reflection velocity analysis based on velocity model scan; Model scan ni yoru sanjigen hanshaha sokudo kaiseki

    Minegishi, M; Tsuru, T [Japan National Oil Corp., Tokyo (Japan); Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)


    Introduced herein is a reflection wave velocity analysis method using model scanning as a method for velocity estimation across a section, the estimation being useful in the construction of a velocity structure model in seismic exploration. In this method, a stripping type analysis is carried out, wherein optimum structure parameters are determined for reflection waves one after the other beginning with those from shallower parts. During this process, the velocity structures previously determined for the shallower parts are fixed and only the lowest of the layers undergoing analysis at the time is subjected to model scanning. To consider the bending of ray paths at each velocity boundaries involving shallower parts, the ray path tracing method is utilized for the calculation of the reflection travel time curve for the reflection surface being analyzed. Out of the reflection wave travel time curves calculated using various velocity structure models, one that suits best the actual reflection travel time is detected. The degree of matching between the calculated result and actual result is measured by use of data semblance in a time window provided centering about the calculated reflective wave travel time. The structure parameter is estimated on the basis of conditions for the maximum semblance. 1 ref., 4 figs.

  15. Evaluation of permeability of Nojima fault by hydrophone VSP; Hydrophone VSP ni yoru Nojima danso no tosuisei hyoka

    Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)


    The multi-offset hydrophone VSP experiments were carried out using a 750m deep borehole as the oscillation receiver, which penetrates the Nojima fault, to detect water-permeable cracks and evaluate their characteristics. Soil around the borehole is of granodiorite, and fault clay is found at a depth in a range from 623 to 624m. A total of 4 dynamite tunnels were provided around the borehole as the focus. The VSP results show that the tube waves are generated at 22 depths, including the depth at which fault clay is found. However, these waves are generated at only 6 depths in an approximately 150m long fracture zone, suggesting that the cracks in the zone are not necessarily permeable. It is also found that crack angle determined by the analysis of tube waves almost coincides with that of fault clay determined by the core, BHTV and FMI, and that permeability is of the order of 100md at a depth of fault clay or shallower. 3 refs., 2 figs., 2 tabs.

  16. Suppression of 3D coherent noise by areal geophone array; Menteki jushinki array ni yoru sanjigen coherent noise no yokusei

    Murayama, R; Nakagami, K; Tanaka, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center


    For improving the quality of data collected by reflection seismic exploration, a lattice was deployed at one point of a traverse line, and the data therefrom were used to study the 3D coherent noise suppression effect of the areal array. The test was conducted at a Japan National Oil Corporation test field in Kashiwazaki City, Niigata Prefecture. The deployed lattice had 144 vibration receiving points arrayed at intervals of 8m composing an areal array, and 187 vibration generating points arrayed at intervals of 20m extending over 6.5km. Data was collected at the vibration receiving points in the lattice, each point acting independently from the others, and processed for the composition of a large areal array, with the said data from plural vibration receiving points added up therein. As the result of analysis of the records covering the data collected at the receiving points in the lattice, it is noted that an enlarged areal array leads to a higher S/N ratio and that different reflection waves are emphasized when the array direction is changed. 1 ref., 6 figs.

  17. Velocity structure of Nojima-fault by VSP method; VSP ho ni yoru Nojima danso no sokudo kozo

    Kuwahara, Y; Ito, H; Kiguchi, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)


    In order to investigate in detail structures of the fractured fault band, the VSP tests were conducted using a 750m deep borehole penetrating the Nojima fault in Awaji Island. The borehole penetrates the fault clay band at a depth of 624m in the Hirabayashi area. The offset VSP survey, conducted by the aid of hydrophone through the naked borehole, detects many characteristic phenomena resulting from the fault fracture. Largely fractured lithofacies are found by the core observation at a depth in a range from 557 to 673m. P-waves propagate at 4.6 and 5.1km/s above and below the fractured band, respectively. The fractured band is subdivided into 2 sections, both being of low speed of 4.5 and 3.1km/s. The X1 and X2 phases resulting from the fault fracture are also observed, above and below the fractured band. The causes for these wave phases are now under investigation. 4 figs.

  18. Three-dimensional TDEM modeling using integral equation method. 2; Sekibun hoteishikiho ni yoru TDEM no sanjigen modeling. 2

    Noguchi, K; Endo, M [Waseda University, Tokyo (Japan). School of Science and Engineering


    A study was made about integral equation-assisted numerical calculation in a time domain electromagnetic (TDEM) 3D modeling. The total number of cells should be minimized now that the time required for calculation depends a great deal upon the total number of cells. On the assumption of a thin plate-like layer of anomaly in presence, with its center positioned just below the receiving point and with its entirety buried in a homogeneous 100 Ohm m medium, the correlation between the distance and the maximum cell length in the horizontal direction and the method of dividing were examined. As the result, it was found that a dividing method respecting the exponential function shortens the calculation time and that, for obtaining a true response and for minimizing the calculation time, the length of the horizontal side of the cell nearest to the transmission source needs be set to be not more than 1/2 of the distance. It was also found that the length of the side in the direction of depth of the topmost cell needs be set to be not more than approximately 1/3 of the depth of the upper surface of the plate-shaped anomaly. 2 refs., 10 figs., 2 tabs

  19. Manufacture of lightweight aggregates utilizing coal fly ash. Sekitan bai riyo ni yoru jinko keiryo kotsuzai seizo

    Ishii, K [Kyushu Electric Power Co. Inc., Fukuoka (Japan)


    Processing of a large amount of coal ash is a serious problem in considering the locational conditions of coal firing power generation plants. 46% of the coal ash was effectively used in 1985, and the remaining 54% was disposed at landfills on land and sea. Positive promotion of the effective use of coal ash is the necessity. A production method for an artificial lightweight aggregate utilizing coal ash was established by a joint research. The history of the research and development of this artificial lightweight aggregate (brand name: FA-lIGHT), outline of the manufacturing facilities, physical properties and result of use are introduced. The lightweight aggregates are used not only for the construction of multistoried buildings but also used as most suitable aggregates for making lightweight large scale panels and concrete secondary products such as lightweight blocks. FA-LIGHT is most suitable for use in the production of concrete lightweight aggregates, and can be used for hydroponic agriculture and for the improvement of drainage of land. Spread of its use is expected. 5 figs., 5 tabs.

  20. Structural study of synthetic polymers by MALDI-TOFMS; MALDI-TOFMS ni yoru gosei kobunshi no kozo kaiseki

    Noguchi, K.; Hirayama, K. [Ajinomoto Co. Inc., Tokyo (Japan)


    As observation results on the time-dependent change in the ring-opening reaction of novolac epoxy resin with acetic acid by MALDI-TOFMS, the epoxy ring was opened with reaction time, the hydroxy group formed by the ring-opening reaction was acetylated, those components were measured. In the case of the FABMS/MS observation of materials and the reaction products, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. In the polymerization of bisphenol A epoxy resin with N, N`-dimethylethylenediamine, it was observed by MALDI-TOFMS that many kinds of polymers with high molecular weight were formed with an increase of reaction time. In this case, the LSIMS/MS observation of materials and the reaction products was carried out, the estimation structure could be confirmed from the measured results of MALDI-TOFMS. 19 refs., 8 figs.

  1. Upgrading of brown coal by slurry-dewatering; Kattan no yuchu dassui ni yoru clean kotai nenryo no seizo

    Okuma, O.; Shimizu, T.; Inoue, T.; Shigehisa, T.; Deguchi, T.; Katsushima, S. [Kobe Steel, Ltd., Kobe (Japan)


    This paper describes an outline of solid fuel production process from brown coal and the investigation results of its elemental techniques. Dried coal is produced by this process which consists of a dewatering of crushed brown coal in oil-based solvent, a solid and liquid separation of slurry, and a remained oil recovery by heating. This process is characterized by the higher thermal efficiency compared with usual drying and the restraint of spontaneous combustion of product coal. It was revealed that solid fuel with low moisture, low ash, low sulfur, and suppressed spontaneous combustion property can be produced from Australian brown coal through this process. From the comparison between kerosene and fuel oil A, it was confirmed that the oil content during dewatering was smaller and the oil recovery by heating was easier by using a solvent with lower boiling point. It was also confirmed that the spontaneous combustion property can be suppressed using small amount of asphalt by solving asphalt in the solvent and adsorbing asphalt on the surface of brown coal. From these results, low rank coals including brown coal, which are difficult to use, are expected to be used as clean coal with low ash and low sulfur through this process. 2 refs., 7 figs., 2 tabs.

  2. Method for analyzing electromagnetic-force-induced vibration and noise analysis; Denjiryoku reiki ni yoru dendoki no shindo hoshaon kaisekiho

    Shiohata, K.; Nemoto, K.; Nagawa, Y.; Sakamoto, S.; Kobayashi, T.; Ito, M.; Koharagi, H. [Hitachi, Ltd, Tokyo (Japan)


    In this analysis method, electromagnetic force calculated by 2-dimensional analysis is transformed into external force for 3-dimensional structural-vibration analysis. And a modeling procedure for a vibrating structure is developed. Further, a space-modal-resonance criteria which relates electromagnetic force to structural-vibration or noise is introduced. In the structural-vibration analysis, the finite element method is used; and in the noise analysis, the boundary element method is used. Finally, vibration and noise of an induction motor are calculated using this criteria. Consequently, high-accuracy modeling is achieved and noise the calculated by the simulation almost coincides with that obtained by experiments. And it is clarified that the-space-modal resonance criteria is effective in numerical simulation. 11 refs., 9 figs., 3 tabs.

  3. Glass marking with diode-pumped Nd:YLF laser; Handotai reiki Nd:YLF laser ni yoru glass marking

    Sakai, F.; Hayashi, K. [Sumitomo Heavy Industries, Ltd., Tokyo (Japan)


    The compact marking system based on a beam scanning system in which the fourth harmonic (FHG: 262 nm in wavelength) of a diode-pumped Nd:YLF (Nd:LiYf4) laser is used for the source of ultraviolet light is described. The result of application to the glass marking that caused a problem due to the generation of cracks is also explained. The machining characteristics significantly vary depending on the type of glass. During actual marking, sample processing must be beforehand carried out to optimize the processing conditions after confirming that there is no problem in practical use. For marking on the glass used for liquid-crystal board, it is valid to improve the density of a dot and increase the number of shots per dot for obtaining high visibility. However, cracks may occur in the clearance of each dot because of the thermal effect. Therefore, the processing conditions must be optimized according to the glass type and crack generation state. The generation of cracks can be suppressed by setting the processing conditions to the optimum level. As a result, satisfactory marking is obtained. 8 refs., 6 figs.

  4. Adaptation of topology optimization on truck-structure; Kinshitsukaho ni yoru iso saitekika shuho no truck kozo eno tekiyo

    Tachibana, H; Kojima, A; Chiba, S [Mitsubishi Motors Corp., Tokyo (Japan)


    An optimization using the homogenization method has been applied to a truck-structure on the concept design stage. A truck-structure is grouped into 3 classes (thin plate structure , thick plate structure and solid structure), then example, effectiveness and method for the application for the purpose of weight reduction , high rigidity and high eigen-frequency are introduced. 3 refs., 24 figs., 1 tab.

  5. Modeling of power train by applying the virtual prototype concept; Kaso genkei ni yoru power train no model ka

    Hiramatsu, S; Harada, Y; Arakawa, H; Komori, S [Mazda Motor Corp., Hiroshima (Japan); Sumida, S [U-Shin Corp., Tokyo (Japan)


    This paper describes the simulation of power train that includes the model developed by applying the virtual prototype concept. By this concept, subsystem models which consist of functional model and mechanism models are integrated into a total system model. This peculiarity in architecture of model, which is called the hierarchical structure, enables us to model a system of large scale with many units, systems and parts easily. Two kinds of computer simulations are performed. One is engine revolution fluctuation by accessory load input, and the other is changing gears by automatic transmission. They are verified to have sufficient accuracy. 2 refs., 12 figs.

  6. Emission and combustion characteristics of multiple stage diesel combustion; Nidan nensho ni yoru diesel kikan no nensho to haishutsubutsu tokusei

    Hashizume, T; Miyamoto, T; Tsujimura, K [New A.C.E. Institute Co. Ltd., Tokyo (Japan); Kobayashi, S; Shimizu, K [Japan Automobile Research Institute, Tsukuba (Japan)


    A new concept of multiple stage diesel combustion was studied by means of engine test, combustion observation and numerical simulation, in order to reduce NOx emissions at high load conditions. With this concept, the premixed combustion occurs under the fuel lean conditions and the diffusion combustion occurs under the high temperature conditions. As seen in the result of combustion observation, a first stage combustion occurs with no luminous flame. A second stage combustion occurs with a luminous flame after very short ignition delay period. However the luminous flame is disappeared immediately. Because cylinder temperature is high, and hence soot oxidizes immediately. 5 refs., 11 figs., 1 tab.

  7. Investigation of iron current measurement to detect combustion quality; Ion denryu ni yoru nensho jotai kenshutsu no kento

    Nakata, K; Mogi, K [Toyota Motor Corp., Aichi (Japan)


    The possibility and problems were investigated in detecting the combustion quality by means of ion current measured at the spark plug. The ion current has two peaks during one combustion stroke; first peak is generated by flame around the spark plug just after ignition and second one appears with the rise in temperature of burned gases. As the result of investigations, it was confirmed that the first ion peak might be useful to forecast the combustion quality, but it would be hard to practice owing to the spark duration. And the second peak offered the information of combustion chamber pressure. 4 refs., 12 figs., 1 tab.

  8. Defect detection of elevator wire rope by using wavelet analysis; Wavelet kaiseki ni yoru elevator rope no sonsho kenshutsu

    Kaneda, M.; Kawata, A.; Hayashi, S. [Kansai University, Osaka (Japan). Faculty of Engineering; Tokui, K. [Mitsubishi Electric Building Techno-Service Co. Ltd., Tokyo (Japan)


    Detecting strand breakage and local wear of elevator wire rope uses currently a method using a rope tester. This method magnetizes a rope with electric magnet and detects defected part as leakage flux. Pulsed signals are issued from the defected part, variation in magnetic flux leakage due to rope swinging produces noise, and both get mixed together. Therefore, the detection is performed finally by visual check and palpation. This paper discusses a method that analyzes measurement data derived by the rope tester by using wavelet conversion, and detects the defected part automatically without being confused by noise. The pulsed signals generated from the defected part can be detected from noise by decomposing multiplex resolution using the Haar basis. As a result of the experiment, cases that may be overlooked in visual check because of S/N ratio being too small or the pulsed signals being too weak were all detected. 11 refs., 14 figs.

  9. High-speed conversion of carbon dioxide into methanol using catalyst. Shokubai ni yoru nisanka tanso no kosoku methanol ka

    Inui, T. (Kyoto University, Kyoto (Japan). Faculty of Enineering)


    This paper describes high-speed conversion of CO2 into methanol. When a Cu-Zn-Cr-Al oxide-based catalyst (MSCp catalyst) prepared by using a sedimentation process used for synthesizing methanol from CO is applied to converting CO2 into methanol, the methanol yield decreases down to a several fraction of CO to methanol conversion, with a possibility of greater catalytic deactivation. If this catalyst prepared by using a homogeneous gelation process (MSCg catalyst) is used, the yield of methanol from CO2 increases by 240 plus percent over the case of using the MSCp catalyst, and no catalytic deactivation occurs at all during a use for ten and odd hours. Further, when La2O3 is added to the MSCg catalyst at 4% by weight, the methanol yield increases by about two times as much as the case without addition, and the temperature at which the maximum yield is achieved shifts to a lower temperature side by about 20[degree]C. Combining Ag or Pd with the MSCg catalyst provides the same effects. The paper touches on an attempt of high-speed CO2 conversion using this catalyst loaded with ceramic fibers. 15 refs., 5 figs., 2 tabs.

  10. Baking of the multi-itemed clinker by the large kiln; Ogata kirun ni yoru tahinshu kurinka no shosei

    Kihara, Yasuhiro [Ube Industies, Ltd., Yamaguchi (Japan)


    In the Ube cement plant, it had 5 DB kilns, and it became a base of the special cement manufacture. However, the productivity difference with the special cement manufacture by the large kiln recently spread, and in the DB cairn, it was judged with the limit. Therefore, the rationalization which put together DB kiln of 5 in NSP kiln of 1 was carried out, while the role of the special cement manufacture base was maintained. In this paper, the outline of variety switching technology in large and single kiln of 1 for the multi-itemed and multi-itemed clinker production is introduced in this. (NEDO)

  11. Synthesis and chemical recycling of high polymers using C1 compounds; C1 kagobutsu ni yoru kobunshi no chemical recycle

    Masuda, T. [National Institute of Materials and Chemical Research, Tsukuba (Japan)


    The paper outlined a study of the synthesis of high polymers using C1 compounds which are continuously usable chemical materials and the related compounds such as the derivatives, and also the chemical recycle. In the case of waste plastics mixed in urban refuse, effective is the chemical recycle where C1 compounds obtained by gasifying the mixed waste are used as high polymer material. For the synthesis and recycle of high polymers using C1 compounds, there are three routes: Route A (recycle via high polymer materials), Route B (recycle via C1 compounds and high polymer materials), and Route C including global-scale carbon recycle (recycle via carbon dioxide from biodegradable plastics using microorganism). Among high polymers, those that can be synthesized from C1 compounds, for example, polymethylene, polyacetal and polyketone can be chemically recycled by Route B. 30 refs., 2 figs., 1 tab.

  12. PWM pulse pattern optimization method using carrier frequency modulation. Carrier shuhasu hencho ni yoru PWM pulse pattern saitekikaho

    Iwaji, Y.; Fukuda, S. (Hokkaido University, Sapporo (Japan))


    Sinusoidal inverters are getting more widely used keeping pace with the development of semiconductor switching elements. This paper discusses optimizing a PWM pulse pattern at an inverter output to drive an induction motor, proposes methods for improving distortion and torque ripples using a carrier frequency modulation (CFM), and describes a method for realizing the improvement through use of a single-chip microcomputer. The method defines evaluation parameters corresponding to the distortion and torque ripples, and optimizes the CFM depth to the parameters. The PWM pulse pattern has its voltage vector and time width so selected that the time integrated space vector of a three-phase voltage approaches a circular locus. Furthermore, the carrier frequency, that is the sampling frequency of the inverter, is also adjusted so that the above evaluation parameters are minimized. The addition of a new variable called the frequency modulation provides freedom in selecting an output characteristic as called for by the purpose. 12 refs., 18 figs.

  13. Toughened cyanate ester alloys via reaction-induced phase separation; Hanno yuhatsugataso bunkai ni yoru taishogekisei cyanate ester alloy

    Hirohata, T.; Kuroda, M.; Nishimura, A. [Sumitomo Electric Industries, Ltd., Osaka (Japan); Inoue, T. [Tokyo Institute of Technology, Tokyo (Japan)


    For the purpose of toughening the matrices of fiber-reinforced plastics (FRPs), the effect of thermosetting/thermoplastic polymer alloys based on cyanate ester alloys is investigated. In the experiment, materials are heated and then allowed to set, which are mixtures of 87.0-43.5wt% of cyanate ester resin, 0-43.5wt% of epoxy resin, and 13.0wt% of soluble polyimide. FRP properties are examined by measuring the after-shock compressive strength, flexural elasticity and flaxural strength, and by performing morphology observation. It is then found that a cyanate ester/soluble polyimide system forms a polymer alloy with phase separation, that its glass transition temperature does not drop, and that the rupture strength is increased approximately twice. A carbon fiber-reinforced plastic (CFRP) incorporating this system is twice higher in after-shock compression strength than a CFRP incorporating a cyanate ester. The system withstands high temperatures, retaining at 200degC approximately 90% of the elastic modulus it exhibits at room temperature. 15 refs., 16 figs.

  14. Development of materials of `bekko work` using horn; Gyukaku riyo ni yoru bekko daitai zairyo no kaihatsu

    Mori, S.; Nagata, S. [Technology Center of Nagasaki, Nagasaki (Japan); Sakoguchi, A. [Kumamoto Institute of Technology, Kumamoto (Japan)


    The technical art `Bekko` is one of the traditional technologies in Japan, and the materials of `Bekko` are shells of hawksbills. However, the industry of `Bekko Work` has been facing a crisis recently, because the import of turtleshell is restricted. We have therefore tried to develop new materials as substitutes for the turtleshell by utilization of horn. The noteworthy aspects in this study are as follows: (a) It has been clearly established that the horn could be reformed with amber color similar to that of turtleshell by chemical treatment using hydrogen peroxide (H2O2). (b) It is also of interest that we produced new materials like `Bekko` by mixing horn powder and turtleshell powder at the appropriate ratio and molding them in the temperature range of 110-120{degree}C. 1 ref., 6 figs., 3 tabs.

  15. Visual communication system among underwater robots and divers. Kaichu robot ya diver kan no shikaku ni yoru tsushin

    Chiba, H. (East Japan Railway Co., Tokyo (Japan)); Ura, T.; Fujii, T. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)


    Performing coordinated works between underwater robots and divers, often called undersea agents, requires communication means to promote mutual understanding. This paper describes a system to make visual communications as a communication means used under sea, and discusses elementary technologies to realize mutual communications between the agents. The visual communication system comprises a device to indicate command patterns that correspond to intentions to be communicated using five electroluminescence (EL) panels, a CCD camera, and a transponder. Discussions were given on image processing to recognize the command patterns, EL panel positions, and communication protocols. As a result of experiments assuming underwater communications between divers and robots, using a water tank, it was found that the command patterns can be recognized if illuminance in the water tank is 100 lux or lower. Validity of the system was verified in the experiments. 4 refs., 9 figs., 1 tab.

  16. Estimation of the charge quantity from solar cell to battery; Taiyo denchi ni yoru chikudenchi eno juden yosoku

    Tsutsumi, K; Nishitani, M [Daiichi University, College of Technology, Kagoshima (Japan)


    In performing an experiment of running a small electric vehicle by installing solar cells in it and by charging the storage battery at a specific voltage, an estimation was made on the charge quantity to the battery for each solar altitude and inclination of a module at different hours. The solar altitude was determined at Daiichi University, College of Technology, according to the month and the time of day from a formula using day-declination and time equation of a chronological table of science. The quantity of global solar radiation was determined by resolving the solar radiation into its direct and diffuse components on the basis of the extra-terrestrial solar radiation quantity with the change in radius vector taken into consideration; and then, the global solar radiation on the inclined face was obtained from the angle of inclination and incidence. On the roof of a Daiichi University building, solar cell modules were installed facing north and south at 0{degree}, 30{degree}, 45{degree}, 60{degree} and 90{degree} each, so that a short-circuit current was measured for each differently inclined angle. As a result of the experiment, shown in an regression formula is a relation between the temperature conversion value of the maximum output of the solar cell at the standard temperature of 25{degree}C and the quantity of solar radiation on the inclined surface. Consequently, it enabled the prediction of a charging quantity, in the case of running a small vehicle with solar cells installed, from the quantity of solar radiation on the inclined surface in the clear weather. 2 refs., 4 figs., 2 tabs.

  17. Application of cytotoxicity test for toxic micropollutants. Saibo dokusei shiken ni yoru yugai kagaku busshitsu osen no hyoka

    Utsumi, H; Hamada, A [Showa University, Tokyo (Japan). School of Pharmaceutical Science; Ono, Y [National Institute of Hygienic Sciences, Tokyo (Japan)


    Considerations were given from a viewpoint of assessing toxicity to human bodies on methods of assessing water pollutants and organisms, and applicability of cytotoxity test using cultured cells to water quality assessment. Biological assessment systems used for water environment may use tests using multicellular organisms, cells, or organelles in cells. The organism assessment method is intended mainly for assessing ecological effects, and a suitable method must be selected upon extrapolating it to human bodies. A toxicity parameter used most frequently in a cytotoxity test is the cell revival rate, and life and death are determined from liberation of enzymes in cells, or with color rejection tests and incorporation tests. There are a number of test specimens of raw tap water and its chlorine treatment condensate that show no mutagenicity but cytotoxity. Efficiencies of removal by means of mild chlorine treatment, fast filtration, and activated carbon adsorption vary greatly with cytotoxity and mutagenicity. Introducing the cytotoxity test is expected of further contributing to improving safety in water quality. 24 refs., 1 fig., 7 tabs.

  18. Electromagnetic analysis of HTSC by advanced fluxoid dynamics method; Kairyogata jisoku ryoshi doryokugakuho ni yoru koon chodendotai no denji kaiseki

    Demachi, K.; Nakano, M.; Miya, K. [The Univ. of Tokyo, Tokyo (Japan). Graduate School of Engineering


    In this study, the improved fluxoid quantum dynamics method which applied the handling of the lattice in the lattice gas automaton method into the fluxoid quantum dynamics was developed. The saving of a memory capacity and the speedup of the calculation were carried out. Using a BSCCO single crystal which introduced a pinning center by the heavy ion irradiation as an analysis object, the validity of this technique was shown by the comparison with the experimental result. By the improved fluxoid quantum dynamics method, the space was made discrete by the triangular lattice in the two-dimensional system. The fluxoid quantum exists only on the lattice point, and received the force from the fluxoid quantum, the Meissner magnetic field and the pinning center in the circumference, and then moved to the 6 neighboring lattice points. Since the pattern of the positional relation of the fluxoid quantum was limited by the use of triangular lattice, the high-speed computation became possible by storing the interaction force into a database. The dependence for the radiation value of the torque in the axial type super-conductive magnet bearings was analyzed, and the possibility of the rotational loss control by the heavy ion irradiation was shown. (NEDO)

  19. Next-generation mass standard using the superconducting magnetic levitation method; Chodendo jiki fujoho ni yoru jisedai shitsuryo hyojun

    Miki, Yukinobu; Shiota, Fuyuhiko; Fujii, Yusaku [National Research Laboratory of Metrology, Tsukuba (Japan)


    The Present mass standard based on the prototype of the kilogram has some serious problems such as surface contamination and unrecoverablity in the case of damage or loss. Research on monitoring and finally replacing the present mass standard are therefore encouraged and some approaches have been proposed. In this article, the superconducting magnetic levitation method, which is one of the approaches that also makes use of the unique properties of superconductivity, is reviewed together with a brief description about mass and electric standards. (author)

  20. Three-dimensional TDEM modeling using finite-difference method; Sabunho ni yoru TDEM ho no sanjigen modeling

    Noguchi, K; Endo, M [Waseda University, Tokyo (Japan). School of Science and Engineering


    Study is made on the theory of three-dimensional modelling of TDEM (Time Domain Electromagnetic) method based on the theory of Wang and Hohmann. A difference scheme is built and investigation is conducted about calculation accuracy with attention paid especially to space and time division, and the obtained optimum value is compared with the analytical solution for a homogeneous medium. As the result, it becomes possible to have a high-accuracy TDEM response thanks to the obtained optimum parameter. In an example, a response is determined in the case of a high-resistivity body in presence near the ground surface. Calculation is performed under the given conditions of a medium 100 ohm/m in resistivity, anomalous bodies 200, 500, 1000, 2000,5000, and 10,000 ohm/m in resistivity, respectively, and a distance in the direction of depth of 20m. The result indicates that it is possible to estimate the effect of the ground surface terrain on a TDEM response. Since the effect of the ground surface terrain emerges at the initial part of a response, it is inferred that consideration of terrain is mandatory in building a model if it is for interpreting the subsurface structure in detail. 5 refs., 7 figs.

  1. Accuracy of parameters of permeable fractures by hydrophone VSP; Hydrophone VSP ni yoru tosuisei kiretsu no tokusei hyoka no seido

    Kiguchi, T; Ito, H; Kuwahara, Y; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Yabuuchi, S; Hasegawa, K [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)


    Hydrophone VSP (vertical seismic profiling) experiment is under way as a technique for detecting subsurface water-permeable cracks by use of boreholes and for evaluating their characteristics (permeability index, crack direction, dip angle). In this report, tube waves observed by hydrophone VSP are subjected to analysis for the determination of water-permeable crack characteristics, the impact caused by errors in the value inputted for analysis is estimated, and a model calculation is performed in case there is no agreement between data from the borehole and data from VSP, all for examining the VSP records for accuracy. When an error rate of 15% is given to the tube wave/P-wave amplitude ratio, a change of 40% or lower results in the permeability index, and a change of 10deg or less in the dip angle, which means that an error in the amplitude ratio does not affect the analysis very much. Changes in the amplitude ratio resulting from changes in crack direction and dip angle differ, dependent on the offset rate. When angular differences among plural crack directions are within 90deg and dip angles within 60deg, the result of analysis represents the average characteristics of the plural cracks. 7 refs., 5 figs., 2 tabs.

  2. Reflector imaging by diffraction stacking with stacking velocity analysis; Jugo sokudo kaiseki wo tomonau sanran jugoho ni yoru hanshamen imaging

    Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T [Japan National Oil Corp., Tokyo (Japan); Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan)


    Concerning seismic reflection survey for geometrical arrangement between pits, the scattering stacking method with stacking velocity analysis is compared with the CDP (common depth point horizontal stacking method). The advantages of the CDP supposedly include the following. Since it presumes an average velocity field, it can determine velocities having stacking effects. The method presumes stratification and, since such enables the division of huge quantities of observed data into smaller groups, more data can be calculated in a shorter time period. The method has disadvantages, attributable to its presuming an average velocity field, that accuracy in processing is lower when the velocity field contrast is higher, that accuracy in processing is low unless stratification is employed, and that velocities obtained from stacking velocity analysis are affected by dipped structures. Such shortcomings may be remedied in the scattering stacking method with stacking velocity analysis. Possibilities are that, as far as the horizontal reflection plane is concerned, it may yield stack records higher in S/N ratio than the CDP. Findings relative to dipped reflection planes will be introduced at the presentation. 6 refs., 12 figs.

  3. Calculation of lobe mixer flow with reynolds stress model. Oryoku hoteishiki model ni yoru lobe mixer ryu no suchi keisan

    Yamamoto, Makoto; Arakawa, Chuichi; Tagori, Tetsuo [Ishikawajima-Harima Heavy Industries, Co., Ltd., Tokyo (Japan) Univ. of Tokyo, Tokyo (Japan). Faculty of Engineering Univ. of Tsukuba, Tsukuba (Japan)


    It is considered that exhaust gas energy of turbofan engine is partly collected to realize the improvement of propulsion efficiency together with the reduction of noise appeared by the change in velocity distribution of exhaust gas flow. Then Lobe mixer was studied and its effectiveness was widely recognized, however the development of more realistic prediction method of exhaust nozzle system including Lobe mixer, is not completed yet. The stress equation model with low Reynolds Number which is easily used by the expansion of Launder Reece Rodi model in three dimension coordinate system was newly constructed. Applicability of the stress equation in more complicated flow field was greatly improved. While the above model was applied to Lobe mixer system, then the qualitative reproduction of mixing process accompanied with flow around Lobe and longitudinal eddy of core or bi-pass flow, was realized. There is room for improvement of pressure strain correlation term and behavior of Reynolds stress very close by wall surface in this model. 16 refs., 9 figs., 1 tab.

  4. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Nakamura, M; Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T [Kyushu University, Fukuoka (Japan)


    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  5. Structural changes in deashed coals induced by heat treatment; Kanetsu shori ni yoru dakkaitan no kozo henka

    Sugano, M.; Sekita, M.; Muramatsu, Y.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology


    Change in structures of 3 kinds of coals with different coal ranks and their deashed coals was studied by heat treatment below 200{degree}C. In experiment, crushed Adaro, Taiheiyo and Huaibei coals below 200mesh and their deashed coals were used as specimens. The coal and deashed coal specimens dried in vacuum at 110{degree}C for 3 hours were filled into an autoclave, and the heat-treated coal specimens were prepared by holding them under initial nitrogen pressure of 2kg/cm{sup 2} at a fixed temperature for 30min. Extraction using pyridine as solvent, volumetric swelling using methanol or benzene as solvent, and measurement of the amount of carboxyl and phenolic hydroxyl functional groups were conducted for these coal specimens. The experimental results are as follows. Huaibei coal has developed aromatic ring structure, and its structure is hardly affected by heat treatment. The oxygen containing functional groups decrease by heat treatment over 100{degree}C in Adaro coal and 150{degree}C in Taiheiyo coal, and PS, MQ and BQ also decrease due to aggregation between molecules. 5 refs., 2 figs.

  6. Prediction of DI diesel engine emissions by multidimensional simulation; Tajigen simulation ni yoru DI diesel engine no seino yosoku

    Ishii, Y; Zhang, L; Hamaguchi, K; Minami, T; Yokota, K [Isuzu Advanced Engineering Center, Tokyo (Japan)


    To achieve the goal of using multidimensional simulation as a useful tool for predicting engine emissions in the stage of design or choice chamber shape and nozzle specifications, much work is needed to improve and modify calculation models. In this study , the spray model of KIVA-II have been modified using experimentally measured penetration of spray liquid phase. The modified KIVA-II was applied to a HSDI engine with different chambers and injectors. As a result of comparing with experiments, it was found that the KIVA-II using the modified spray model could relatively predict the change of emissions. 6 refs., 12 figs., 2 tabs.

  7. Effect and limitation of tuning accelerator pedal sensitivity by DBW; DBW ni yoru akuseru kando settei no koka to genkai

    Takada, Y; Morita, S [Osaka City University, Osaka (Japan)


    DBW (Drive By Wire) system makes the constraint of direct connection between an accelerator pedal and the throttle valve free, so that optionally turning of throttle valve sensitivity becomes possible in automobiles driving. Reported here is the discussion of the effect and the limitation of this optionally tuning. As the former result, it became clear that the tuning method using torque signal and speed signal of the drive shaft, was easier than the method using only speed signal by PD control action. And as the latter result, upper limit was bound by the low gear ratio and tire spin. 2 refs., 11 figs.

  8. Confinement of solar thermal energy by Nesa film; Nesa maku ni yoru taiyo netsu energy no fujikome

    Shimizu, A; Yano, K; Kasuga, M; Daigo, Y [Yamanashi University, Yamanashi (Japan). Faculty of Engineering


    This paper reports a Nesa (SnO2) film as selective transmissive film for effective confinement of solar thermal energy. Solar light spectrum ranges from 0.3 to 2.0{mu}m, while thermal radiation from bodies at 100-200degC is infrared ray more than 2{mu}m. Consequently, a solar water heater using the film which can pass rays below 2.0{mu}m while reflect rays over 2.0{mu}m for windows is very efficient. The Nesa film reflects rays with wavelengths more than plasma wavelengths (controllable from 1 to several {mu}m) by plasma action of free electrons. The Nesa films with different carrier densities were fabricated by spraying deposition method at dopant rates (Sb/Sn) from 0 to 2mol%. The solar water heaters were prepared using normal glass and specific glass coated with the Nesa film as selective transmissive film. The heater using the glass coated with the Nesa film of 2{mu}m plasma wavelength for windows could efficiently confine solar heat. The Nesa film of 700nm plasma wavelength which can pass visible light while reflect infrared ray was effective to reduce cooling/heating losses. 3 refs., 6 figs.

  9. Realization of an accelerator for environmental refreshment in case of soil; Fukyugata kasokuki ni yoru kankyo sosei eno koka

    Isogai, H [Electrotechnical Laboratory, Tsukuba (Japan)


    Learning from a history of the earth of ancient times, the paper studies effects of refreshing environment and soil or making them natural and harmless mostly using primitive bacteria, and develops element technology which is industrially accelerating. The spread type accelerator working only by solar energy was installed and operated for experiment. As indices of refreshment effects, a study was comparatively made between a sugar degree of sweet potato and a yield shown in the number of potatotimesunit weight. An EM propagation garbage layer is formed, and the two sections were installed of a site of the actual installation of the spread type accelerator and a site naturally left alone. Other effects of weather, temperature and humidity which are external factors and general fertilization are offset as common modes, and a consideration was so made that only refreshment effects of primitive bacteria can be relatively compared. Acceleration effects in using accelerator for growing sweet potato could be quantitatively confirmed. As to sugar degree, because the last study was made in the beginning of summer, the underground temperature was high enough. Even only EM effects were fully effective. This time, the weather was much colder, and it was found to be a must to use accelerator. 2 figs.

  10. Monitoring of EOR operations by electrical prospecting. 2; Denki tansaho ni yoru sekiyu kyosei kaishuho no monitoring. 2

    Ushijima, K; Mizunaga, H; Tanaka, T; Masuda, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tamagawa, T [Japex Jeoscience Institute, Tokyo (Japan)


    Fluid flow tomography (FFT) was applied to monitor the behavior of underground fluid in steam enhanced oil recovery (EOR) for oil sand reservoirs. FFT uses electrode arrangement of a mise-a-la-masse method, and continuously measures time variation in charged and spontaneous potential at various surface points to obtain realtime the images of underground seepage flow. It continuously measures ground surface potentials of 120 channels at intervals of 2s by applying alternative DC between a casing pipe and distant current electrode. It separates charged and spontaneous potential components, and converts them into time series data. It estimates the time and spacial distributions of seepage flow from time variation in spontaneous potential. It determines the change rate distribution of time-sliced apparent resistivity from charged potential to estimate the scale and area of seepage flow. As the experimental result, positive and negative electrodes in the change rate distribution were observed, and the direction connecting each electrode agreed with that of resistivity anomaly. FFT could observe realtime time variation in apparent resistivity due to steam injection. 9 refs., 7 figs.

  11. Monitoring of IOR/EOR operations by electrical prospecting; Denki tansaho ni yoru IOR/EOR monitoring

    Ushijima, K; Mizunaga, H; Ikeda, H; Masuda, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    Fluid flow tomography (FFT) was developed to monitor enhanced oil recovery IOR/EOR operations. This method uses a casing pipe as linear current source by connecting a current electrode with a well inlet, and the other electrode is grounded at a point far different from the well. Potentials are rapidly measured at the same time by multi-channel receiving electrodes installed on the ground to obtain time series data composed of charged potential and superimposed spontaneous potential. After separation of both potentials, the charged potential data are processed by the conventional mise-a-la-masse method to extract local anomaly, determine the residual distribution and relative change distribution of time-sliced apparent resistivity, and obtain the 3-D profile of fluid. The spontaneous potential is also processed to obtain the deflection distribution of time-sliced potential at a specific time. Quantitative 3-D interpretation is conducted focusing attention on the generation mechanism of spontaneous potential. Behavior of underground permeated flow is determined as time series animation images to image fluid direction. This method was effective in real fields. 8 refs., 4 figs.

  12. Resistivity structures imaging using time-domain electromagnetic data; TDEM ho ni yoru chika hiteiko kozo no imaging

    Noguchi, K [Waseda University, Tokyo (Japan). School of Science and Engineering; Endo, M [Waseda University, Tokyo (Japan)


    The kernel function for transient vertical magnetic dipole was defined for semi-infinite uniform medium, and the 1-D imaging algorithm by TDEM (time-domain electromagnetic) method was developed for underground resistivity structure. Electromagnetic migration method directly images sectional resistivity profiles from the data observed by frequency-domain MT method, and determines underground resistivity profiles by integral equation of MT field using the concept of return travel time in reflection seismic exploration. The method reported in this paper is also one of the EM migration methods. The imaging algorithm of 2-D resistivity structure was developed by correcting 1-D imaging in consideration of the effect of 2-D anomaly on 1-D imaging (the resistivity of anomaly can be obtained from the resistivity contrast between anomaly and medium). The conventional methods require enormous forward computation, while this method can obtain underground resistivity structure in extremely short computation time, resulting in superior practicability. 12 refs., 7 figs.

  13. Development of low rank coals upgrading and their CWM producing technology; Teihin`itan kaishitsu ni yoru CWM seizo gijutsu

    Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Tsurui, M; Suto, Y; Asakura, M [JGC Corp., Tokyo (Japan); Ogawa, J; Yui, M; Takano, S [Japan COM Co. Ltd., Japan, Tokyo (Japan)


    A CWM manufacturing technology was developed by means of upgrading low rank coals. Even though some low rank coals have such advantages as low ash, low sulfur and high volatile matter content, many of them are merely used on a small scale in areas near the mine-mouths because of high moisture content, low calorification and high ignitability. Therefore, discussions were given on a coal fuel manufacturing technology by which coal will be irreversibly dehydrated with as much volatile matters as possible remaining in the coal, and the coal is made high-concentration CWM, thus the coal can be safely transported and stored. The technology uses a method to treat coal with hot water under high pressure and dry it with hot water. The method performs not only removal of water, but also irreversible dehydration without losing volatile matters by decomposing hydrophilic groups on surface and blocking micro pores with volatile matters in the coal (wax and tar). The upgrading effect was verified by processing coals in a pilot plant, which derived greater calorification and higher concentration CWM than with the conventional processes. A CWM combustion test proved lower NOx, lower SOx and higher combustion rate than for bituminous coal. The ash content was also found lower. This process suits a Texaco-type gasification furnace. For a production scale of three million tons a year, the production cost is lower by 2 yen per 10 {sup 3} kcal than for heavy oil with the same sulfur content. 11 figs., 15 tabs.

  14. Fracture mapping in rock slope using geophysical instruments; Butsuri tansa ni yoru ganban shamennai no kiretsu bunpu hyoka

    Kurahashi, T; Inazaki, T [Public Works Research Institute, Tsukuba (Japan); Watanabe, S [Geological Survey of Japan, Tsukuba (Japan)


    An attempt was made to visualize distribution of cracks in a rock slope by applying geophysical survey onto a rock slope. Geophysical logging and seismic survey using the reflection method were used as the methods for the geophysical survey. The rock slope subjected to the survey is located in a gorge along the Yoshino river in Yamashiro Town, Tokushima Prefecture. The slope has a width of 25 m and a height of 30 m. Its overhang in a nose form may has a possibility of causing collapse due to sliding. Cracks developed by horizontal schistosity were detected by performing geophysical logging on VSP, calipers, natural gamma-ray spectra, temperature and borehole in a borehole drilled vertically from the top of the slope. The seismic survey using the reflection method detected the cracks by emphasizing joints in the perpendicular direction. A possibility was shown to visualize the crack distribution with high resolution by using the above geophysical survey on the rock slope. In order to detect the crack distribution with still higher resolution, development into a three-dimensional exploration in the future is desired, not to speak of improvement in signal receivers, and discussions on geometry. 1 ref., 6 figs.

  15. Application of vector CSAMT for the imaging of an active fault; CSAMT ho ni yoru danso no imaging

    Kobayashi, T; Fukuoka, K [Oyo Corp., Tokyo (Japan)


    With an objective to identify three-dimensionally resistivity in deep fault in the Mizunawa fault in Fukuoka Prefecture, a measurement was carried out by using the CSAMT method. The measurement was conducted by arranging seven traverse lines, each line having observation points installed at intervals of about 500 m. Among the 68 observation points in total, 33 points performed the vector measurement, and the remaining points the scaler measurement. For observation points having performed the vector measurement, polarized wave eclipses were depicted in the electric field to discuss which direction the current will prevail in. For analyses, a one-dimensional analysis was performed by using an inversion with smoothing restriction, and a two-dimensional analysis was conducted by using the finite element method based on the result of the former analysis. The vector measurement revealed that the structure in the vicinity of a fault was estimated to have become complex, and the two-dimensional analysis discovered that the Mizunawa fault is located on a relatively clear resistivity boundary. In addition, it was made clear that the high resistivity band may even be divided into two regions of about 200 ohm-m and about 1000 ohm-m. 2 refs., 7 figs.

  16. Detection of multiple AE signal by triaxial hodogram analysis; Sanjiku hodogram ho ni yoru taju acoustic emission no kenshutsu

    Nagano, K; Yamashita, T [Muroran Institute of Technology, Hokkaido (Japan)


    In order to evaluate dynamic behavior of underground cracks, analysis and detection were attempted on multiple acoustic emission (AE) events. The multiple AE is a phenomenon in which multiple AE signals generated by underground cracks developed in an extremely short time interval are superimposed, and observed as one AE event. The multiple AE signal consists of two AE signals, whereas the second P-wave is supposed to have been inputted before the first S-wave is inputted. The first P-wave is inputted first, where linear three-dimensional particle movements are observed, but the movements are made random due to scattering and sensor characteristics. When the second P-wave is inputted, the linear particle movements are observed again, but are superimposed with the existing input signals and become multiple AE, which creates poor S/N ratio. The multiple AE detection determines it a multiple AE event when three conditions are met, i. e. a condition of equivalent time interval of a maximum value in a scalogram analysis, a condition of P-wave vibrating direction, and a condition of the linear particle movement. Seventy AE signals observed in the Kakkonda geothermal field were analyzed and AE signals that satisfy the multiple AE were detected. However, further development is required on an analysis method with high resolution for the time. 4 refs., 4 figs.

  17. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Nakamura, M.; Koterayama, W. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H. [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T. [Kyushu University, Fukuoka (Japan)


    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  18. Distributed scheduling for autonomous vehicles by reinforcement learning; Kyoka gakushu ni yoru mujin hansosha no bunsangata scheduling

    Unoki, T.; Suetake, N. [Oki Electric Industry Co. Ltd., Tokyo (Japan)


    In this paper, we propose an autonomous vehicle scheduling schema in large physical distribution terminals publicly used as the next generation wide area physical distribution bases. This schema uses Learning Automaton for vehicles scheduling based on Contract Net Protocol, in order to obtain useful emergent behaviors of agents in the system based on the local decision-making of each agent. The state of the automaton is updated at each instant on the basis of new information that includes the arrival estimation time of vehicles. Each agent estimates the arrival time of vehicles by using Bayesian learning process. Using traffic simulation, we evaluate the schema in various simulated environments. The result shows the advantage of the schema over when each agent provides the same criteria from the top down, and each agent voluntarily generates criteria via interactions with the environment, playing an individual role in tie system. 22 refs., 5 figs., 2 tabs.

  19. Function analysis of working integrated circuit with scanning laser microscope. Laser kenbikyo ni yoru IC no dosa kansatsu

    Ode, T. (Lasertec Corp., Kanagawa (Japan))


    By scanning a laser light, the reaction of a specimen against the light is detected in some means. The optical effect can be visualized by displaying that on the CRT or the like in synchronism with the scanning. Among these, an image formed and visualized by internal photoelectric effect by light is called OBIC image, and chiefly used for evaluating and analyzing semiconductor devices. Observing this OBIC image by a high speed scanning laser microscope has been spotlighted these days as an effective means for observing the state of p-n junction of an IC in operation. This paper descries the principle, the observing method, the detecting circuit, etc. of the semiconductor observing method using a laser microscope. Further, actual examples of detecting defects of an IC by means of OBIC image are shown. As for the problem, since leak parts are displayed as negative contrast in the OBIC image to affect finding work of leak part, the necessity of improvement is pointed out. 39 refs., 11 figs.

  20. Improvement of residual stress in stainless steel by cavitating jet; Cavitation funryu ni yoru stainless ko no zanryu oryoku kaizen

    Soyama, H.; Saka, M. [Tohoku Univ., Sendai (Japan)] Park, J. [Kyung Nam Junior College, Pusan (Korea, Republic of). Dept. Vehicle Eng.] Abe, H. [Tohoku Univ., Sendai (Japan)


    In order to strengthen materials, the improvement of residual stress in stainless steel by using a cavitating jet was investigated. In case of cavitating jet, the cavitation intensity can be controlled by hydraulic parameters such as upstream pressure and downstream pressure. In general, cavitation produces damage on hydraulic machinery. However, at the initial stage of cavitation erosion process, plastic deformation takes place on the material surface, then it is possible to do peening without damage considering the cavitation intensity and the exposure time. In order to evidence the suitable condition on the improvement of residual stress by the cavitating jet, the residual stress in SUS304 and SUS316 was examined. The three normal stresses in different directions were measured by X-ray diffraction method, then the principal stresses were calculated. Both principal stresses were changed from tension to compression within 10 seconds by the cavitating jet. The compressive stress resulted by the cavitating jet was saturated after a certain time. It was concluded that the cavitating jet improved the residual stress in stainless steel SUS316 as well as SUS304. 24 refs., 9 figs.

  1. Tidal energy conversion. Renewable energy; 3-3 choseki / choryu hatsuden. II. saisei kano energy ni yoru hatsuden

    Makino, T. [Tobishima Corp., Tokyo (Japan)


    There are not much examples applying tidal energy conversion, but tide and tidal current phenomena can be forecasted so correctly regardless of weather that the applying tidal energy is to be expected in the future. The largest tidal power plant is at Reims in France and install 24 Kaplan turbines each of which outlet power is 10,000kW (rotational direction is reversible) on the breakwater (750m is length). Tidal range at this place being 8.5m on an average, during the period of flowing seawater into the reservoir and on the contrary during the period of discharging seawater to the sea generation is both performed. Though there is no actual result of tidal power plant in Japan, in tidal current power system experimental generators have been installed at Kurushima channel and Naruto channel. Nihon University carried out various kinds of experiment using a Darius turbine (1.6m in dia.) at Kurushima channel and got outlet power of 3kW at the maximum (1983-`88). There are few coasts which have sufficient tide range in Japan, but there are so good many applicable coasts in China and Southeast Asia that the tidal power generation is to be expectatively. 12 refs., 5 figs., 1 tab.

  2. Smoke reduction using multiple stage diesel combustion; Nidan nensho ni yoru diesel kikan no smoke teigen koka

    Tsujimura, K. [Chiba Institute of Technology, Chiba (Japan); Hashizume, T.; Miyamoto, T.; Akagawa, H.


    A new diesel combustion concept termed MULDIC (MULtiple stage Diesel Combustion), which can reduce NO{sub x} emissions at high load conditions, was studied by means of engine test, combustion observation and numerical simulation. The engine test showed that simultaneous reduction of NO{sub x} and smoke could be obtained with MULDIC operation. In-cylinder combustion observation was carried out in order to clarify the cause of the smoke reduction of the MULDIC. In these photographs, a first stage combustion sins observed with nonluminous flame. In a second stage combustion, a highly sooting luminous flame was observed because the ignition delay was short. However this luminous flame disappeared quickly. Computational results showed that, oxygen is distributed evenly in the cylinder in later portion of the second stage combustion. Moreover, since cylinder temperature was very high, most of the soot oxidized rapidly. Thus, low smoke combustion was obtained. (author)

  3. Developing chiral technologies. Optical division by liquid chromatography; Hattensuru kiraru technology. Ekitai chromatography ni yoru kogaku bunkatsu

    Onishi, a. [Daicel Chemical Industries, Ltd., Osaka (Japan)


    Optical division using chiral fixing phase for polysaccharide derivative based HPLC has been exhibiting superior capability as an analysis means. It now has transcended the framework of analysis as a result of the encounter with the SMB process, and is completing itself as an optically active body manufacturing means. This paper introduces the following examples of applying the chiral fixing phase for HPLC using polysaccharide derivatives as an unconformity identifier to the unconformity identifying mechanism and mass synthesis: 1) aromatic groups and carbamate groups as substitution groups are arranged regularly along a polysaccharide main chain having a regular and unconformable stereostructure, and a certain `unconformity identification field` is formed: 2) hydrogen bonding and dipole-to-dipole interactions take place between solutes in the ester groups and carbamate groups, and such an interaction act as stacking of aromatic rings among those having aromatic rings; and as a result, interactions in 2) occur in the `unconformity identification field` in 1), where the unconformity identification is executed. This paper describes the pseudo migration bed (SMB) process developed by UOP Corporation as a method for mass-synthesizing fillers for the polysaccharide derivative based HPLC. 6 refs., 3 figs.

  4. 6kW class laser cutting equipment; 6kW daishutsuryoku laser setsudanki ni yoru atsuita setsudan

    Nagata, Y.; Nagahori, M. [Tanaka Engineering Works Ltd., Saitama (Japan)


    Application of the laser cutting machine to the area of cutting steel plates of 5 mm thick or more was first enabled in 1990 by the 2 kW oscillator that was introduced in that year. The thick plate cutting industry has a short history. This paper describes the features and performance of the 6 kW laser cutting machine that was announced in April, 1994. The machine uses a newly developed high-speed axial flow type carbon dioxide laser oscillater with the rated output of 6 kW. As the discharge excitation method, the machine adopted the RF (radio frequency) method that causes low contamination in the discharge tube. The 6 kW laser cutting machine has a number of features such as a large cutting area provided by the oscillator contained in the cutting machine, cutting quality stabilized by the optical path length fixing unit, and automatic functions such as automatic setting of the cutting conditions and scheduled operation. The machine can cut mild steel plates of up to 40 mm thick (or up to 16 mm for stainless steel plates) at the cutting speed of 1600 mm/min for a 16 mm thick plate and 2200 mm/min for a 12 mm thick plate, with the good cut sectional surface. 5 figs., 1 tab.

  5. Biological wastewater treatment technology with application of multihole glasses. Takoshitsu glass wo riyoshita biseibutsu ni yoru haisui shoriho no kenkyu

    Honda, S; Murayama, Y; Tanaka, H; Yazawa, T; Eguchi, K [Government Industrial Research Institute, Osaka (Japan)


    This paper describes efficiency improvement in wastewater treatment to separate SS component using anaerobic fermentation with fixable microorganisms and multihole glass separation films. Measurement of microorganism deposition on microporous PVF resin in a fermentation tank revealed that hydrophilic resins with smooth surface have better deposition, and the suitable carrier hole diameters were from 300[mu]m to 500[mu]m. Adding slightly-soluble carbonate when bacteria are fixed collectively is effective in preserving the entire methane fermentation reaction system and stabilizing the carriers. A composite film comprising SiO2-ZrO2-based porous glass made by using a sol-gel process and porous ceramics had the maximum desalination rate reaching 90%. The permeation rate at a film thickness of 2[mu]m was 46 times as much of that for 500-[mu]m single-layer porous glass. As a result of reforming the pore surface by introducing -Si(CH3)3, the film has turned affinitive to non-polar solvent, repelling water to permeate. In an experiment for fermentation liquid permeation of separation film composite bioreactor using digestive sludge, the higher the SS particle concentration, the more the initial clogging was difficult to occur. The film permeating flow velocity showed a maximum value at hole diameters of about 0.2[mu]m. 3 refs., 6 figs., 2 tabs.

  6. Detection of buried pipes by polarimetric borehole radar; Polarimetric borehole radar ni yoru maisetsukan no kenshutsu jikken

    Sato, M.; Niitsuma, H. [Tohoku University, Sendai (Japan); Nakauchi, T. [Osaka Gas Co. Ltd., Osaka (Japan)


    If the borehole radar is utilized for detection of buried pipes, the underground radar measurement becomes possible even in the situation where the mesurement on the earth surface is difficult, for example, such a place as under the road where there is much traffic. However, since buried pipes are horizontally installed and the existing borehole radar can send/receive only vertical polarization, the measurement conducted comes to be poor in efficiency from a viewpoint of the polarization utilization. Therefore, by introducing the polarimetric borehole radar to the detection of buried pipes, a basic experiment was conducted for the effective detection of horizontal buried pipes. Proposing the use of a slot antenna which can send/receive horizontal polarization in borehole in addition to a dipole antenna which sends/receives vertical polarization, developed was a step frequency type continuous wave radar of a network analyzer basis. As a result of the experiment, it was confirmed that reflection from buried pipes is largely dependent on polarization. Especially, it was found that in the slot dipole cross polarization mesurement, reflection from buried pipes can be emphasized. 4 refs., 5 figs.

  7. Free convective heat loss from cavity-type solar furnace; Solar receiver kara no shizen tairyu ni yoru netsusonshitsu

    Fujii, I; Ito, N [Meiji University, Tokyo (Japan)


    Free convective heat loss from solar heat receivers was studied, using three laboratory model receivers (different in depth L and aperture diameter d) heated by electric heaters. Most of the heat produced by heaters was transmitted to the air inside. The cylindrical vessel walls were fully insulated against heat. Heat loss being supposed to result mainly from transfer by free convection, the experiment results were edited by use of Nusselt number Nu and Rayley number Ra. Relations between Nu(D/d){sup m1} and Ra(L/D){sup m2} were plotted in a chart. Here, D is the receiver inner diameter, and m1 and m2 are constants that can be determined by computation. Tests points were provided approximately lineally, irrespective of D, L, or receiver inclination. Air currents were found to produce one or more swirls inside, thanks to the current visualization technique, when the receiver inclination was not sharper than 120{degree} (except 0{degree}). The number of swirls increased as the inner wall temperature rose. This kind of behavior of air currents directly affects the degree of heat loss. 9 refs., 4 figs.

  8. Study of removing a peat-layer from surface active agents; Deitanso ni yoru kaimen kasseizai no jokyo

    Umemiya, H; Kitamura, K [Yamagata University, Yamagata (Japan)


    An experiment was performed on a system for recycling water resources by using a peat-layer. A laboratory device was also made in order to examine the effects of a peat-layer on surface active agents. In the experiment, a water examination was carried out in which a mixture of water and kitchen detergent at the rate of 15,000 to 1 was filtered through a peat-layer of 2-3cm thick, as was a mixture of water, kitchen detergent and oil at the rate of 15,000 to 1 to 2. In the water examination, various measurements were done such as the measurement of COD by potassium permanganate acid process, measurement of pH by a pH meter with glass electrodes and measurement of coefficient of permeability by a variable water level permeability test. As a result of the experiment, it was revealed that a peat-layer had ability to remove surface active agents, that injection water tended to increase acidity in a peat-layer and that a peat-layer had ability to remove foaming of surface active agents. The COD of domestic waste water decreased from 12mg/l to 0.16mg/l in the system for recycling water resources using a peat-layer. 3 refs., 10 figs., 1 tab.

  9. Cooling effects of artificial water facilities by using a moving type turbulence promoter; Kudo ranryu sokushintai ni yoru suireikyaku jikkenho

    Miyake, K; Nomura, T; Nishimura, N; Iyota, H [Osaka City University, Osaka (Japan)


    Artificial water facilities present an effective means to alleviate trying micrometeorological phenomena such as warming of the urban space. For the reproduction of such an alleviating means by use of a model in a wind tunnel, a moving disturbance promoter (moving spire) was developed so as to render disturbances in a wind tunnel current similar in scale to ones in the real atmosphere, and an air current cooling experiment was conducted using a model fountain. The effort was intended for a small-size wind tunnel without a space large enough for disturbance promoter installation, and a moving type spire was developed for promoting disturbance effectively. The new spire is driven by a driving unit consisting of a motor and cam and can change its angle relative to the main current by 140{degree} at a rotation cycle of 1.7Hz., and this changes the flow direction of the main current periodically. As compared with the generally used combination of a roughness block and stationery spire, this new spire produced a disturbance intensity two times greater and a disturbance scale three times larger. When the disturbance intensity and scale were increased, the cooling characteristics of the air current changed in response to changes in the state of flow. 8 refs., 7 figs., 1 tab.

  10. Shift operation control of automatic transmission by {mu}-synthesis; {mu} synthesis ni yoru jido hensokuki no hensoku seigyo

    Nagaoka, M; Nishiyama, Y; Nakayama, Y; Kamada, S [Mazda Motor Corp., Hiroshima (Japan)


    We have developed a control technology, which the robust control theory is applied, to improve a shift quality of automatic transmission for a passenger car. When applying the robust control theory to the transmission control, many issue arise such as difficulty in system identification and/or the capability of ECU for computing. Recently, We have obtained an exact performance that allows the transmission to be robust controlled with an onboard ECU by improving the system identification process and reducing the model dimensions after the controller design finalized. 6 refs., 7 figs.

  11. Microfiltration of soy sauce sediment with rotating disk membrane module; Kaitengata enbanmaku module ni yoru shoyuori no roka

    Matsushita, K.; Kanekuni, N.; Nogaki, H.; Itakura, I.; Shimizu, Y.; Watanabe, A. [TOTO Ltd., Kitakyushu (Japan)


    Soy sauce sediment is formed in pasteurization of raw soy sauce. It is treated as industrial waste, though its main component is soy sauce, because of difficulty in perfect clarification of the suspension. In this paper, we decided a suitable range of pore size of microfiltration and a cut-off level of ultrafiltration to clarify soy sauce sediment and we developed a rotating disk membrane module (RD Module) and compared performance with conventional a multi-tubular membrane module (MT Module). The optimum range to obtain soy sauce of quality was less than a pore size of O.2{mu}m for microfiltration, while ultrafiltration was not suitable for soy sauce sediment. Ultrafiltration was restricted by rejection of colors and nucleic acids and related compounds in soy sauce sediment, rather than rejection of bacteria and ethanol. An RD Module could recover soy sauce of quality and was superior to an MT Module for concentration ratio, but the permeate fluxes of the RD Module decreased under conditions of high revolution as centrifugal forces were exerted on the permeate in the disk membrane. The power consumption of the RD Module was proportional to the cube of number of revolutions and to the fifth power of the radius, so it was found that one of methods for the scale up is to increase the number of disk membranes than increase the radius. 15 refs., 8 figs., 1 tab.

  12. Improved practical formulas for estimation of cable tension by vibration method; Shindoho ni yoru cable choryoku jitsuyo santeishiki no hosei

    Zui, H. [Setsunan University, Osaka (Japan). Faculty of Engineering; Shinke, T. [Kobe Technical College, Kobe, Kobe (Japan); Hamazaki, Y. [Kobe Steel, Ltd., Kobe (Japan)


    The vibration method is usually utilized on the measurement of cable tension during construction of cable bridge such as Nielsen bridges or cable stayed bridges. Practical formula for the vibration method previously proposed by authors is often used where bending rigidity is taken into account. These formula, however, have a certain limit of application and do not yield good results when the cable is not slender or not enough mentioned. The practical formula is modified to improve the accuracy and new formulas are made. The new practical formulas are applicable to any cables, regardless of its length and tension in it. The accuracy is confirmed through comparison of the value obtained by practical formulas with measured values and calculated value by F.E.M. 2 refs., 4 figs., 1 tab.

  13. Large-diameter boring of rock bed by a reveres circulation drill; Ribasu sakyureshon doriru ni yoru daikokei ganban sakko

    Sakae, S.; Torii, K. [Kajima Corp., Tokyo (Japan); Hoshino, S.; Motoyama, M.


    The Itojima Large Bridge is a road bridge of 675 m in the total length connecting together the Nagashima Island and the Itojima Island in the northwest district of Kagoshima Prefecture, having a central span of 260 m and comprising a 5-span-continuous PC cable stayed bridges and PC box girder bridges. The foundation of this bridge employs a multi-pillar type pile structure. The piling work was started in July, 1991 by a hole inset method in a severe working environment where the depth of water is 20 m, the range of the tides is 4 m, the speed of tidal current is 2 kt, the rock bed structure is complicated and the steep seabed is steeply inclined. This report describes the results of the execution of the reverse circulation drilling, which has a high general versatility in rock bed boring, using self-lifting barges and large working boats during the rock bed boring for the foundation piling for the construction of the Itojima Large Bridge. The report, especially, also introduces the details of the work that casing pipes were driven into a stable rock bed by a vibrojet method for the measure against the collapse of a bore wall which occurred during the boring work. 24 figs., 14 tabs.

  14. Leveling of battery load and extension of battery life by serial connection of electric double layer capacitors with batteries for electric vehicles. Experimental results on the small model; Denki jidoshayo denchi to denki nijuso capacitor no chokuretsu setsuzoku ni yoru denchi futan no heijunka oyobi denchijumyo no enshinka. (kogata model ni yoru jikken seika). Kogata model ni yoru jikken seika

    Takehara, J.; Okubo, N.; Miyaoka, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)


    The load leveling method of batteries for electric vehicles was studied for extension of a battery life and mileage every charging. Under large load fluctuation conditions such as deceleration and acceleration, use of electric power sources other than battery for peek load at acceleration can improve a battery life, output power capacity and mileage every charging. Combination of effective recovery of regenerative power at deceleration with its discharge at acceleration is one of the effective methods. The electric double layer capacitors are serially connected with the batteries, regenerative power is charged only into the capacitors, and both voltages of the battery and capacitor are applied to a power circuit. Battery load is reduced by load on the capacitor. Until the capacitor is re-charged by regenerative power after full discharge, power is supplied only by battery through a diode. Capacitor power is used as effectively as possible until approaching considerably low voltage. As peak load of the battery is reduced by 30%, the mileage increases by 5.7%, and the battery cycle life becomes 1.5 times longer. 7 refs., 5 figs., 3 tabs.

  15. Investigation on the chemically fixing technique of carbon dioxide utilizing solar energy; Taiyo energy riyo ni yoru nisanka tanso no kagakuteki koteika gijutsu ni kansuru chosa


    This report describes the results of effective fixing technique of CO2 by utilizing solar energy. First of all, the investigation was directed to the technique for synthesizing ethylene, hydrocarbons and alcohol by electrochemical reduction of CO2. The power required for this process is supplied by photovoltaic power generation. Development of excellent electrode catalyst is needed because the reduction of CO2 requires a high overvoltage. It is desirable to enhance the selectivity of the reaction for specific material and improve the transport process in the electrolytic cell. Next, designing of material and reaction of photocatalysts using semiconductor electrode and semiconductor particulate was examined. A semiconductor electrode made of FeS2 is inexpensive and has a high ability of collecting solar light. In the category of photocatalysis system, a photocatalytic system in which semiconductor particles are embedded in vesicle and a photpocatalyst based on potassium niobate are noteworthy. As biosystem, the method of reducing CO2 by calcareous algae which simultaneously advances fixing and calcification of CO2 by photosynthesis is noteworthy. 129 refs., 45 figs., 20 tabs.

  16. Evaluation for characteristics of around the Nojima fault; Butsuri tansa ni yoru `Nojima jishin danso` shuhen no jiban bussei ni kansuru ichihyoka

    Shimizu, K; Tsuji, T [Newjec Inc., Osaka (Japan); Tsuji, M [OYO Corp., Tokyo (Japan)


    Various surveys were conducted for the area around the Nojima fault, including ground surface, two-dimensional electrical and boring surveys and elastic wave tomography, in order to grasp properties of the ground around the `Nojima earthquake fault.` The resistivity image method as one of the two-dimensional electrical methods was used to grasp fault shapes over a wide range of the 1.6km long section extending between Esaki and Hirabayashi. The courses of traverse were set in the direction almost perpendicular to the fault. Boreholes were excavated and elastic wave tomography was conducted between the boreholes on the 9th and 17th courses of traverse, to confirm ground/mountain conditions and to compare the results with observed elastic wave velocities. Very low resistivities are observed at places where granite is distributed, suggesting that the fault-induced changes are not limited to the area around the fault. The zone in which elastic wave velocity decreases is narrow, 10m at the longest, at a velocity of 2.4km/s or lower, which is a low velocity for that propagating in granite. 5 refs., 4 figs.

  17. Interpretation of seismic section by acoustic modeling. Study of large amplitude events; Hadoba modeling ni yoru jishin tansa danmen no kaishaku. Kyoshinhaba event ni taisuru kosatsu

    Tamagawa, T; Matsuoka, T; Sato, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Minegishi, M; Tsuru, T [Japan National Oil Corp., Tokyo (Japan)


    A large amplitude event difficult to interpret was discovered in the overlap section in offset data beyond 10km targeting at deep structures, and the event was examined. A wave field modeling was carried out by use of a simplified synclinal structure model because it had been estimated that the large amplitude event had something to do with a synclinal structure. A pseudospectral program was used for modeling the wave field on the assumption that the synclinal structure model would be an acoustic body and that the surface would contain free boundaries and multiple reflection. It was found as the result that a discontinuous large amplitude event is mapped out in the synclinal part of the overlap section when a far trace is applied beyond the structure during a CMP overlap process. This can be attributed to the concentration of energy produced by multiple reflection in the synclinal part and by the reflection waves beyond the critical angle. Accordingly, it is possible that phenomena similar to those encountered in the modeling process are emerging during actual observation. 2 refs., 8 figs.

  18. Interpretation SP anomaly caused by subsurface fluid flow; Chika ryudokei ni yoru shizen den`i anomaly no kaishaku ni tsuite

    Yasukawa, K [Geological Survey of Japan, Tsukuba (Japan); Mogi, T; Kawahira, M [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    A PTSP simulator, developed by combining a fluid flow simulator and a simulator for computing the spontaneous potential (SP) out of flow velocity distribution, was used to investigate the impact of the distribution of terrain, permeability, and resistivity upon the ground surface SP. SP computation using simple models such as highlands or cliffs indicated that the terrain-caused SP anomaly was negatively dependent upon elevation. It was also indicated, however, that, in some types of resistivity distribution, the SP profile changes, the peak goes out of place, and even the apparent polarity may reverse in extreme cases. In the study of the SP profile for the Takeyu hot spa, Oita Prefecture, PTSP-aided modeling was carried out. It was then found that fluid flows caused by the terrain were not enough to explain the peak at the middle of the mountain, which suggested the existence of a fluid flow caused by temperature distribution. 11 refs., 5 figs.

  19. Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

    Inagaki, Y; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering


    This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

  20. Evaluation stationariness of triaxial seismic while drilling and detection of reflected wave; Kosei kussaku ni tomonau danseiha no sanjiku kaiseki ni yoru hiteijo hyoka to hanshaha no kenshutsu

    Yoshida, T; Asanuma, H; Niitsuma, H [Tohoku University, Sendai (Japan). Faculty of Engineering


    This paper reports a method to detect reflected wave components contained in an elastic wave caused in association with well drilling. Measurement was made on an elastic wave caused in association with well drilling in an experimental field by using a triaxial elastic wave detector disposed in a measurement well. Analyzing the particle motion tracks in the derived elastic wave signals (to derive the main axial direction of a three-dimensional hologram) revealed that oscillation direction of the signals changes non-steadily by time centering around the S-wave oscillation direction. In addition, a sound source position was estimated during the drilling. Existence probability of the S-wave signal in the non-steady continuous signals was estimated by handling the particle motion tracks stochastically. In addition, this existence probability was used as a weighting function for a correlative analysis to detect a reflected wave from directly reaching wave components in the non-steady continuous signals. Thus, improvement in reliability of reflected wave detection was attempted. Effectiveness of this method was endorsed by the field data. 3 refs., 7 figs.

  1. Study on heavy duty truck stability control by braking force control; Seidoryoku seigyo ni yoru truck no sharyo kyodo anteika ni taisuru ichikosatsu

    Matsuda, K; Shinjo, H; Harada, M; Ohata, K; Sakata, K [Mitsubishi Motors Corp., Tokyo (Japan)


    Now a days we are discussing about the vehicle stability control system which freely controls the braking force of each wheel to apply the yaw t and decelerate the vehicle. The system drastically improve the vehicle cornering performance and stabilize the vehicle behavior in its critical area. This paper discusses a point to notice in case of applying this technique for heavy duty trucks, and describes the possibility of the stabilization for vehicle cornering behavior about heavy duty truck. 3 refs., 10 figs., 2 tabs.

  2. Estimation of performance of a high-speed boat by using the Rankine source method; Kosokutei no rankinsosuho ni yoru seino suitei ni tsuite

    Eguchi, T [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)


    This paper describes estimation of performance of a high-speed boat by using the Rankine source method. An orthogonal coordinate system is considered, which uses the center of a hull as the zero point, and is made dimensionless by using the hull length. The catamaran boat or the single hull boat being the subject of the discussion is supposed to have a transom stern, and to be sailing at a constant speed in the -X direction. A governing equation and a border condition were formulated using disturbance speed potential and X-direction speed differentiation. An inverse specular image was employed as a specular image system upon considering attitude change in the high-speed boat. As to the division of hull surface, the portions protruded above the static water surface were cut off from among the panel data of boat CAD. Considering a high speed condition in which the water surface is completely separated at the transom section, the water level at the transom section was supposed to be at the same height as at the rear end of the hull. Blow-out intensity at the water surface was derived in such a way that a CAD panel of the rear end of the hull is searched and wave height agrees with the height of the transom in the Z direction. A resistance curve may be obtained easily by using a personal computer. 4 refs., 8 figs.

  3. Formation of secondary products in water purification. ; Charactarization of chlorination by-products. Josui shori ni okeru fukuseiseibutsu. ; Enso shori ni yoru shodoku fukuseiseibutsu no seisei tokusei

    Aizawa, T [The Inst. of Public Health, Tokyo (Japan)


    Chlorination of drinking water is an inevitable process for the purification of drinking water. It has been made clear that injected free chlorine reacts with organic matter in water to produce chlorinated by-products. Many of those compounds are toxic, and studies have been made on the international water quality standard. Water quality standard has been revised also in Japan. The sources of organic matter which is the cause for production of chlorinated by-products vary according to the kinds and conditions of the water source for drinking water. Removal of precursors in the original water, removal of by-products, and change in the disinfection system with alternate disinfectant for chlorine are among the measures for decreasing chlorinated by-products at water purification plants, but the first one is employed as the basis method. It is expected that more severe regulation may be imposed on the quality of the water source for drinking water, and more strict oxidation and disinfection systems is inevitable for water management based on the new water quality standard. 10 refs., 5 figs., 2 tabs.

  4. MT survey in the Minaminoshiro oil field; Minaminoshiro chiiki ni okeru MT ho ni yoru sekiyu tanko (sanjigen MT ho chosa no kento). 1

    Matsuo, K; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center


    Preliminary experiment, investigation, and study are conducted prior to an experimental 3-D MT (magnetotelluric) survey planned to be carried out in the Minaminoshiro district, Akita Prefecture. In the preliminary investigation, MT measurements were performed at nine locations. It was anticipated that national highways, waste treatment plants, high-voltage power lines, and railways in presence in the district would act as noise sources. Although the impact of such noise was detected in the single site treatment result, yet it was found that it would be mostly eliminated by use of the remote reference treatment. It was learned that the resistivity structure in this district was quite low in contrast or 1 ohm/m against 30 ohm/m, but the result of 3-D model calculation indicated that a sufficient analysis would be possible even in such a low contrast case. Furthermore, as the result of the study of the density of observation stations in the magnetic field, it was found that changes in the response of magnetic field to the resistivity structure would be approximately 2% at the maximum and that the ill effect on the result of measurement would be of the negligible magnitude even when a single magnetic field observation station is deployed against plural electric field observation stations. 6 refs., 7 figs.

  5. Estimated method of permeability in the granitic rocks by geophysical loggings; Butsuri kenso shuho ni yoru kakoganchu no tosuisei ni kansuru ichikosatsu

    Matsuoka, K; Hashimoto, N. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)]Ogata, N. [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)


    Water permeability in granite is estimated by performing geophysical investigation using a 500m-deep test hole drilled in granitic rocks in the vicinity of a Tono mine. The investigation consists of flowmeter logging and geophysical logging. In flowmeter logging, a probe is moved up and down in the hole at a constant speed by use of a cable, and the cable speed and impeller revolution are used to workout the relative speed of the fluid in the hole. In the geophysical logging, a probe attached to the leading end of a logging cable is replaced with other probes so as to acquire different geophysical data. In a hole drilled in a crack-abundant rockbed such as a granitic rockbed, the inflow and outflow of ground water is governed mainly by water-permeable crack zones, and the result of the flowmeter logging show that this hole has three highly water-permeable zones. Using the results of the loggings, a correlative equation is worked out between changes in flow speed and changes in permeability index obtained by hydraulics tests. Among the various results achieved by the geophysical logging, a fine correlationship is found between an equation relative to permeability obtained using electricity and density and water-permeability indexes obtained by hydraulic tests conducted in situ. 4 refs., 8 figs., 1 tab.

  6. Global environmental benefits of industrial heat pumps (fiscal 1993); 1993 nendo koon heat pumping gijutsu ni yoru chikyu ondanka keigen koka ni kansuru chosa kenkyu hokokusho



    An investigational study was conducted aiming at making a quantitative grasp of effects of the spread of industrial heat pumps on energy conservation and greenhouse gas reduction and at promoting the spread. Finally, the following eight countries joined this international joint research: Canada, France, Japan, Holland, Norway, Sweden, the U.K. and the U.S. Each country share the work and expenses for the research with each other. Japan made investigational researches on the application of heat pumps to processes of the chemical industry, oil refining industry, food industry, paper/pulp industry, and dyeing/weaving industry, and on the effects of greenhouse gas reduction. As procedures taken, values up to 2010 were estimated of energy prices in each country, energy supply/demand, rates of the heat source configuration for electric power supply, etc., the heat flow of the above-mentioned process was made clear, and analyses were conducted of annual profits, energy consumption, and depreciation period in the case of adopting heat pumps. Moreover, the energy conservation amount and greenhouse effect gas reduction amount were estimated based on the result of the analyses. 69 figs., 196 tabs.

  7. Optimization of the ship type using waveform by means of Rankine source method; Rankine source ho ni yoru hakei wo mochiita funagata saitekika ni tsuite

    Hirayama, A; Eguchi, T [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)


    Among the numerical calculation methods for steady-state wave-making problems, the panel shift Rankine source (PSRS) method has the advantages of rather precise determination of wave pattern of practical ship types, and short calculation period. The wave pattern around the hull was calculated by means of the PSRS method. The waveform analysis was carried out for the wave, to obtain an amplitude function of the original ship type. Based on the amplitude function, a ship type improvement method aiming at the optimization of ship type was provided using a conditional calculus of variation. A Series 60 (Cb=0.6) ship type was selected for the ship type improvement, to apply this technique. It was suggested that optimum design can be made for reducing the wave making resistance by means of this method. For the improvement of Series 60 ship type using this method, a great degree of reduction in the wave making resistance was recognized from the results of numerical waveform analysis. It was suggested that the ship type improvement aiming at the reduction of wave-making resistance can be made in shorter period and by smaller labor compared with the method using a waveform analysis of cistern tests. 5 refs., 9 figs.

  8. Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2



    Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

  9. Fundamental study on leak detection of underground gas pipeline using passive acoustic method; Judogata onkyo keisoku ni yoru maisetsu gas dokan hason kasho no kenshutsu ni kansuru kenkyu

    Jinguji, M; Imaizumi, H; Kunimatsu, S; Isei, T [National Institute for Resources and Environment, Tsukuba (Japan)


    With an objective to detect gas leaking from an underground gas pipeline, discussions have been given on a method which utilizes acoustic characteristics of leakage. On leaking sound generated from damaged portions, the form of damaging was hypothesized as pinholes, and spectra of leaking sounds from holes with different diameters were measured. The dominant frequency decreases as the hole diameter increases, while it is in a region of relatively high frequency of 1 kHz or higher. However, detection from the ground surface was impossible when cover soil has thickness from 0.5 to 1.5 m. In an experiment to measure leaking sound inside the pipe, pressure in the pipe was adjusted to 0.02 atm which is a standard pressure for a low-pressure pipe, and the sound was measured when the hole diameters were varied. In any of the results obtained by varying the hole diameter, spectra having the dominant frequency in the region of 1 kHz or higher were measured. In addition, it was found that sound pressure difference of as much as 50 dB at maximum is generated as compared with a case of no sound leakage. The above results verified that monitoring the high frequency of 1 kHz or higher is effective in detecting leakage from small damages. 2 refs., 4 figs.

  10. Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho



    With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

  11. Study on load levelling by means of the control of air conditioner operation; Kuchoki kado seigyo ni yoru fuka heijunka ni kansuru ichikosatsu

    Sasaki, H. [Hiroshima University, Hiroshima (Japan); Sadakuni, S. [Japan Broadcasting Corp., Tokyo (Japan)


    The recent drastic increase in the number of air conditioners has caused sharp and narrow peaks in summer seasons due to the inherent temperature sensitive characteristics. The authors proposed to reduce the peak power demand by controlling air conditioner operations, verifying its effectiveness on peak demand clipping. However, the former study has shortcomings in that any qualitative treatment of room temperatures or pleasant feeling was not attempted and it did not provide a way of assessing peak demand clipping in a power system as a whole. In this paper, we shall first propose a new control method that can compromise pleasant feeling and reduction in power demand. Although air conditioners are used to pursue `pleasant feeling`, this contradicts to reduce power consumption and further more the concept of `pleasant feeling` is very vague. Hence, `Weber-Fechner`s law` is utilized to quantify the pleasant feeling which is treated as fuzzy quantity. Fuzzy co-ordination method is used to compromise power demand curtailment and pleasantness. In the second part of this paper, we shall propose an approach of assessing the amount of peak load clipping when the newly proposed control strategy is adopted in a real size power system: A decrease in the required generation capacity is estimated provided that the Loss of Load Probability (LOLP) is maintained at the same level before and after the application of the new control strategy. The reduction can be regarded as a dividend of load management. 5 refs., 9 figs., 5 tabs.

  12. Tyre noise predictions from computed road surface texture induced contact pressure; Romen no outotsu ni kiinsuru sesshoku atsuryoku ni yoru tire soon no suitei

    Mikami, T. [Japan Automobile Research Institute Inc., Tsukuba (Japan)


    A method for tire/road noise prediction is studied based on the result of road surface profile measurement (horizontal direction measurement interval 3mm, horizontal direction measurement accuracy 8{mu}m, distance measured 1655m, using a laser-aided profile meter). The obtained road surface profile is used for the calculation of contact pressure that occurs between the tire tread and road surface (using the 2-dimensional calculation model of Clapp et al.). For the examination of the relationship between the contact pressure and generated noise, tire noise is measured using a microphone array provided near the tire circumference. The frequency spectral ratio between the generated noise and contact pressure is determined as a transmission function. It may be said that the transmission function is unique to the tire, not dependent on the road surface profile. The road surface profile is determined by use of the transmission function, and this enables the prediction of the noise from the tire. Noises were measured on several kinds of road surfaces different in coarseness for a passenger car and truck, and the values from these actual measurements are compared with the predicted values, and then it is found that the prediction model is valid. (NEDO)

  13. Hydraulic mechanism of siltation in approach channels and harbors. Siltation ni yoru koroter dot hakuchi maibotsu no suiri kiko ni kansuru kenkyu

    Irie, I [Kyushu Univ., Fukuoka (Japan). Faculty of Engineering; Murakami, K; Tsuruya, H [Ministry of Transportation, Tokyo (Japan). Port and Harbour Research Inst.


    The phenomena that clay or mud is carried away by waves or currents and deposited in approach channels and harbors are called siltation, and hinder often seriously the navigation of vessels and their arrival at as well as departure from wharves, etc.. In this paper, the hydraulic mechanism of siltation in harbors and approach channels in the sea area is chozen in particular, and waves and currents as the external force governing the travel of bottom mud, the properties of sunken mud, the supply source of sunken mud in approach channels, and grasping of the mud sinking mechanism as well as countermeasures against mud sinking are stated mainly centering around the results obtained from the in situ observations at Kumamoto Port and Banjarmasin Port and their mathematical calculations. The bottom mud traveling mechanism has been accepted as a study subject respectively from such wide viewpoints as river engineering, agriculture, environmental engineering, sanitary engineering, chemical engineering and mechanical engineering, and in addition, it has been under study by coastal engineering. Siltation under the wave actions is still in the state of research even in advanced countries in America and Europe. The siltation research in Japan has a short history, but this is the field which must be coped with positively. 19 refs., 17 figs.

  14. Disinfectants used in medal field and problems caused from their use. Igaku ryoiki ni okeru sakkinzai to sorera shiyo ni yoru mondaiten

    Okuda, K; Watabe, S [Yokohama City University, Yokohama (Japan). School of Medicine


    This paper describes typical anti-microorganism chemicals used in hospitals, and touches on measures against intra-hospital infection. Killing microorganisms reliably by using a high-pressure steam sterilization method is the best means for medical devices and apparatuses. However, there are high-priced medical devices that cannot withstand such a method and require other processes according to the situations, such as gas sterilization and alcohol disinfection. In addition to such sterilization methods as using heat, alcohols, and gases, methods that have been developed recently may include the following: use of Bronopol (an antiseptic) and anti-mold agents that have electronphilic functional groups, disinfectants using metal ions from silver, zinc and copper, and other materials. The problem of intra-hospital infection is caused typically by MRSA, hepatitis virus and Pseudomonas aeruginosa. Preventive measures require good knowledge about their infection courses and disinfecting technologies, as well as an attention not to cause change in the ecology as a result of using excessively strong chemicals. 18 refs., 1 fig., 1 tab.

  15. Analysis of flow and turbulence in high pressure spray by image processing technique. Gazo shori ni yoru koatsu funmunai ni okeru ryudo to midare no kaiseki

    Yamaguchi, I. (Japan Automobile Research Institute, Inc., Tsukuba (Japan)); Nishida, M.; Nakahira, T.; Komori, M.; Tsujimura, K.


    The image processing technique (reported previously) developed for analyzing combustion in a diesel engine was applied to measuring flow and turbulent intensity in a high pressure spray. Copper vapor laser beam in a sheet form with a thickness of 0.2 mm was injected into the cross section of a spray center in a container. Photographs of the scattered lights of the beam is converted into digital values and analyzed using an image processing equipment. With the laser light emitting frequency set to 20 KHz at a maximum, the flow velocity is measured from changes in photographic image density in two subsequent photographs, and the turbulence intensity from changes in brightness intensity. As a result, it was clarified that the flow velocity and the turbulence intensity in the spray cross section increase with raising the spray pressure. Further discussions are being made on the measuring method, including changes in the image brightness associated with entrance and exit of spray particulates into the laser beam sheet, and effects of the laser beam sheet thickness on the measurements of the turbulence intensity. 6 refs., 6 figs.

  16. Characteristics of radiation temperature and radiosity coefficient by means of infrared radiometer. Sekigai hoshakei ni yoru zairyo hyomen no hosha tokusei ni tsuite

    Okamoto, Y; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T; Sato, K [Ibaraki University, Ibaraki (Japan); Kurokawa, T [NEC San-ei Instrumentsu Ltd., Tokyo (Japan)


    A radiation thermometer was applied to the measurement and analysis of radiation temperature of the material surface. In this paper, the characteristics of the radiation temperature and the radiosity coefficient of gray body materials are investigatied. An infrared radiometer was used, which detects radiation energy in the region between 8 and 13{mu}m of wavelength. This infared radiometer has a Hg-Cd-Te photon radiation sensor. The variation of emissivity was measured for the four kinds of non-metalic materials, i.e., graphite, carbon fiber composite, Si-SiC ceramic, and black paint spread on an aluminum plate. As a result, the relationship between material temperature and radiation energy was made clear. Furthermore, the space-dependent variation of the radiation temperature and the radiosity coefficient was derived from the two-dimensional CRT image of the infrared radiometer. Consequently, the emmisivity variation gave a maximum for the carbon fiber composite surface rich in irregularity, and decreased in the order of graphite, Si-SiC, and black paint. 7 refs., 15 figs.

  17. Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa



    For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

  18. Results of geophysical survey on Hanaore-fault in the Kyoto urban area; Butsuri tansa ni yoru Kyoto shigaichi ni okeru Hanaore danso chosa

    Yoshioka, T. [Geological Survey of Japan, Tsukuba (Japan); Echigo, T. [Osaka Soil Test, Osaka (Japan); Toshioka, T.; Matsubara, Y. [Oyo Corp., Tokyo (Japan)


    This paper reports results of gravity survey and seismic survey using the shallow bed reflection method to identify distribution of the Hanaore fault in the Kyoto urban area. In the gravity survey, level differential structure caused by the fault was identified as an abrupt change in Bouger anomalous values. The continuity therefrom made the estimation possible on existence and positions of such faults as the Hanaore fault belonging to the Hanaore fault system, the Shishigaya fault, the Kaguraoka fault, and the Okazaki fault. The estimation as a result of the gravity survey include the following findings: the Hanaore fault runs from south of the Yoshidayama in the south-north direction; the distribution of the Okazaki fault has a level differential structure falling on the east side; the structure shows low Bouger anomaly distribution; and this area forms a rift valley belt. In the seismic survey using the shallow bed reflection method, no distinct reflection plane considered as the basement was verified because of influence from urban area noise. However, it was possible to estimate such an underground structure as a monoclinal fold from shapes of the reflection plane and the distribution depths. 7 refs., 5 figs.

  19. Stability analyses of urban water supply systems with wastewater reuse; Toshi haisui no junkan riyo ni yoru mizu kyokyu anteika ni kansuru kenkyu

    Watanabe, H.; Zhang, S. [Meijo Univ., Nagoya (Japan); Okada, N. [Kyoto Univ., Kyoto (Japan). Disaster Prevention Research Inst.


    Wastewater reuse can be considered as a type of water resource development which is expected to improve the aquatic environment, as well as the stability and reliability of municipal water supply systems. To this extent, wastewater reuse has been taken into account in the planning of water supply systems in several Japanese cities. However, to date the effect of wastewater reuse on water supply system stabilization has not been discussed quantitatively, and the relation between waster water reuse rate and water supply system stability has not been analyzed. In this study, a stochastic model has been presented to evaluate the stability of water supply systems with optimal wastewater reuse rate. Some theoretical analyses and numerical studies were performed, and all of the results have shown that the model is reliable for not only basic studies on water supply system stability, but also for practical use as well. 5 refs., 5 figs., 3 tabs.

  20. Development of multi-filter spectroradiometry; Filter hoshiki ni yoru bunka hosharyo no keisoku hoho to sono supekutoru no hyogen hoho ni tsuite

    Miyake, Y; Aoshima, T; Minoda, T; Kato, T; Kondo, S [Eiko Instruments Trading Co. Ltd., Tokyo (Japan)


    Described in this paper is a technique of solar radiation spectroradiometry in which high-resolution wavelength computation adds to a multi-filter method. The solar spectrum upon entering the atmosphere is scattered and absorbed by parameter-constituting elements such as gas, aerosol, cloud particles, etc., and its spectral contour is complicatedly deformed relative to wavelength. Taking advantage of the fact that the scattering and absorbing characteristics of some of the elements are constant relative to wavelength, a simple equation was constructed to enable high-resolution spectrum measurement wavelength-wise, and this compensates for the limit in measurable wavelength that the conventional multi-filter method suffers from. The new method discussed here is not so expensive as the grating method thanks to the employment of filters, is capable of determining spectral radiation quantities with a precision of {plus_minus}5%, and is reduced in terms of the capacity of memory for data storage. The new method enables data collection under various atmospheric conditions that the four seasons present, which the difficult-to-apply and expensive spectroradiometer fails. It is expected that this method will find its use in collecting basic data for the designing of photovoltaic power generation systems, in the study of photochemical reaction in agriculture, and in collecting basic data for daylight lighting. 1 ref., 6 figs., 2 tabs.

  1. Research on giving antibacteria activity of tailored dental materials; Gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu



    The secondary dental caries easily occur by breeding of bacteria in cavities between living body and composite resin, false tooth or root of tailored tooth as tooth repairing materials. The antibacteria activity of tailored dental materials was thus studied by implanting Ag ion. The antibacteria effect with time after culture of caries bacteria was studied by implanting Ag ion into SiO2 powder, PMMA samples and Ti alloy samples at 20 and 200keV in energy of ion. In addition, the antibacteria activity of SiO2 powder as composite material was found at 25keV which was previously effective for the antibacteria activity. This SiO2 filler (Ag{sup +} filler) showed the antibacteria activity on every bacteria sample after 2h, and in particular, could kill all of 3 kinds of bacteria obtained from a composite resin surface after 12h. The number of living S. salivarius was reduced by half after 12h. The application of the composite resin filler implanted with Ag{sup +} is significant to prevent recurrence of caries. 5 refs., 27 figs., 7 tabs.

  2. Study on a new type variable valve lift timing mechanism with a three dimensional cam; Sanjigen cam ni yoru shinkahen valve lift timing kiko ni kansuru kenkyu

    Ogura, M; Song, C [Nippon Institute of Technology, Saitama (Japan)


    The variable valve timing mechanism was invented to get a torque band at wide engine speed, and to reduce a compression job and pumping loss by a miler cycle at partial load. In this paper, the new type variable valve timing mechanism applying a three dimensional cam was proposed. Also, the feature of mechanism and the control system was done obviously. Further, about a miler cycle, a thermodynamics -like consideration was described. 5 refs., 8 figs.

  3. Ni hombres ni mujeres providenciales

    Montaño Virreira, Sonia


    Debo advertir a la y el lector de este texto que lo que a continuación se presenta no es, ni de lejos, una propuesta realista, si por ella entendemos la traducción, enclave mujer, de las actuales tendencias de liderazgo político vigentes en la región. Por el contrario, intento argumentaren favor de un liderazgo que supere el caudillismo como estilo y se aproxime al máximo hacia el respeto de las formas, entendiendo que sin ellas no es posible construir la democracia. Para hacerlo reviso rápid...

  4. Effects of air pollution on the health of regional inhabitants. Part I. Survey of disease state by Enquete. Taiki osen ga chiiki jumin no kenko ni oyobosu eikyo ni tsuite-dai ippo; anketo ni yoru shojo chosa


    From May to July 1972, the disease states of 2096 inhabitants (710 men and 1386 women) in the Fukushima Ward of Osaka City, where the concentration of sulfur trioxide in the air was (yearly average) 1.81 mg/day/100 sq cm and that of carbon monoxide was 5.3 ppM, and that of nitrogen dioxide was 5.3 ppM, were surveyed. The number of persons surveyed was 2.9% of all the inhabitants of the Ward. Twenty-two point one percent were in their thirties, 20.1% in their forties, 16.5% in their sixties, and 15.3% in their fifties. Those who experienced chest diseases were 2.9% of the total, and those with heart diseases were 1.5%. Non-smoking men were 31.7% of the total. The percentage of long-term complaints of cough and sputum was 11.8% in the eastern section, 11.2% in the northern section, 10.0% in the southern section, 6.8% in the western section of the Ward. The frequency of complaints was highest in the sixties (12.7%), followed by 11.5% in the fifties, 11.3% in the thirties, and 8.6% in the forties. The frequency of complaints from men was 11.1% and that from women was 6%. The frequency of complaints was 19.8% in smokers, 8.5% in those who smoked less, and 6.8% in non-smokers. The frequency of complaints classified by residential area showed 12.6% in industrial areas, and 7.8% in residential and commercial areas. The frequency of complaints of inhabitants who live along National Road No. 2 was relatively high, ranging from 15.0 to 18.8%, and the frequency of complaints of inhabitants was apparently higher than those of people who only work in the Ward.

  5. Development of hydroponic system using agricultural waste. 2. Utilization of ozone for sterilization of nutrient solution; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 2. Ozone ni yoru baiyoeki sakkin ni kansuru kento

    Terazoe, H; Yoshihara, T; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)


    Discussions were given on a sterilizing effect of ozone on Fusarium bacteria in hydroponic culture, and its effect on components in the culture solution. In an experiment, dry air with O3 concentration of 3.5 ppm was sent into aqueous solution inoculated with Fusarium bacteria at a flow rate of 5 liters per minute. The Fusarium bacteria was sterilized nearly completely in about five minutes. No change was observed in pH, EC and dissolved oxygen concentration of the O3-treated culture solution. However, iron and manganese among the soluble components have been oxidized by O3 and precipitated, hence these components must be added after the O3 treatment. In spinach culture performed on a culture medium inoculated with Fusarium bacteria, ozone water containing dissolved O3 at 0.8 ppm was flown into a urethane foam medium and vegetable roots. This treatment has resulted in reduction of the number of strains occurred with a wilt symptom below that in the section flown with distilled water. The spinach has grown normally without showing an effect of the ozone water. 15 refs., 10 figs., 3 tabs.

  6. FY1998 research report on the basic research on geothermal district heating in Kamchatka, Russia; 1998 nendo Roshia Renpo Kamchatka shu ni okeru chinetsu riyo ni yoru chiiki danbo ni kansuru kiso chosa hokokusho



    Petropavlovsk-Kamchatky (P-K) city in Kamchatka, Russia is operating hot-water district heating using heavy oil boilers and waste hot water of thermal power plants as heat sources. Feasibility study was made on district heating using natural geothermal hot water and/or geothermal heat pump systems as heat sources of hot water supply for reduction of greenhouse effect gas emission. Among 3 areas including geothermal hot water, use of hot water in K area was impossible because of lower temperature and less spring water. Use of hot water in P and UP areas was impossible as primary hot water because of temperature drop to 64 degrees C during hot water supply toward P-K city. The building heating operation test was carried out using the geothermal heat pump system installed in a newly drilled heat exchange well of 100m deep. As a result, sufficient heat recovery was achieved for heating. If all of 49 boiler houses for heating are replaced with such geothermal heat pump systems, CO{sub 2} reduction was estimated to be 520,000t/y. (NEDO)

  7. Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

    Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering


    The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

  8. Characteristic analysis of methane-gas generation by oxidizing heat of stored coal and hold ventilation control; Sekitan unpansen ni okeru sanka hatsunetsu ni yoru methane gas hassei to sonai kankyo seigyo ni tsuite

    Fukuchi, N; Nakashima, T [Kyushu Univ., Fukuoka (Japan); Kudo, S


    A demand of coal shows the tendency in the increase worldwide, with this, the marine transportation of the coal gradually increases, and the collier has also enlarged. The traffic pattern of coal is mainly the bulk transportation. In this transportation system, by the oxidation exothermic reaction of the coal, methane gas is produced, simultaneously the coal quality such as coking property or heat quantity is decreased and sometimes spontaneous ignition is caused. Therefore, it is necessary to equip with a ventilator to control the concentration of methane gas and to avoid the self heating of the coal. In this study, the quantity of methane-gas produced by heating coal using an electric furnace was measured and the experiment to investigate the temperature dependency of the methane-gas generated from the coal was conducted. By using the result of the measurement, the quantity of methane-gas produced from the coal stored in the hold of a coal cargo was estimated. And, the mathematical analyses on the changing degree depend on the times of a temperature in the hold under navigation, a concentration of oxygen and a concentration of methane-gas, were conducted. 11 refs., 19 figs., 2 tabs.

  9. Estimation of overprotection region on the painted steel plate under impressed-current cathodic protection. Gaibu dengenho ni yoru inkyoku boshoku ka no toso kohan ni okeru kaboshoku iki ni tsuite

    Iwata, M.; Huang, Y.; Fujimoto, Y. (Hiroshima Univ., hiroshima (Japan). Faculty of Engineering)


    Painting and cathodic protection are used in combination as a corrosion resisting measure for ship hull. n analytic method which uses the boundary element method for protection electric field by impressed-current method is proposed to show that rational determination is possible for the arrangement and current of the anode, and the arrangement and set voltage of the reference electrode used to control the current. However, repetitive calculation is necessary until overprotection voltage disappears from the surface of the painted steel plate while giving optional insulated area because the insulated area of adequate dimension is unknown. To decrease the number of this repetitive calculation, a study is made on a method of estimating the magnitude of the insulated area to be input as the initial value in the electric field analysis by the boundary element method. Although the insulated area has been empirically obtained, such formurization may be useful for automatic optimization using a computer of the location and number of anode, anode current, arrangement and set voltage of the reference electrode, magnitude of the insulated area, etc. in the impressed-current cathodic protection system. 2 refs., 10 figs., 1 tab.

  10. Few studies of the effect of diluents on extraction of cobalt with D2EHPA. D2EHPA ni yoru Co no chushutsu ni ataeru kishakuzai no eikyo ni kansuru jakkan no kento

    Aranae, M.; Nakataka, Y.; Wakamatsu, T. (Kyoto Univ., Kyoto (Japan). Faculty of Engineering); Saito, I.; Sakamoto, H. (Environment Research Inst. Resources Technical Tsukuba (Japan))


    Study was made on extraction of cobalt from weak acid solution with di-(2-ethylhexyl) phosphoric acid (D2EHPA) using various polar diluents such as benzene, toluene, o-xylene, m-xylene, n-heptane, cyclohexane and n-hepatne-benzene mixtures. Extraction efficiency of cobalt has decreased in the order, n-heptane > cyclohexane > m-xylene > o-xylene > toluene > benzene and this order has been in good agreement with the decreasing order of solubility parameters of diluents,and has shown the possibility of application of regular solution theory. When n-heptane and cyclohexane as diluents, in low loading ratio(L),were used Co-D2EHPA polymer were formed compared to other diluents. On the other hand when mixture of n-heptane/benzene was used as diluent, the efficiency of extraction, salting-out effect and formation of Co-D2EHPA polymer has changed with the texture of mixture.This change may be due to the effect of L and it has been thought for the necessity of investigation of extraction of cobalt in low polar diluents. 13 refs., 5 figs., 2 tabs.

  11. Relationship between the electric resistivity and the rain fall in discontinuity zone of rock slope by the continuous measurement; Renzoku tokei ni yoru ganban shamen no furenzokutaibu ni okeru mikake hiteiko henka to kou tono kankei ni tsuite

    Kusumi, H; Nishida, K [Kansai University, Osaka (Japan). Faculty of Engineering; Nakamura, M [Newjec Inc., Osaka (Japan)


    The relationship between change in resistivity and rainfall was studied by continuously measuring resistivities of fracture zone and stratum boundary along the measuring line of 95m long from the top to bottom of rock slope. The measurement field was located on a hill of 150-200m high at the northern part of Arima-Takatsuki tectonic line. Electrodes of 30m in maximum measuring depth were arranged at 289 points by dipole-dipole method. Resistivity was continuously measured at time intervals of 6 hours. Apparent resistivity was hardly affected by rainfall at points with less infiltration of stormwater from the ground surface, while it decreased by rainfall at points on fracture zone, stratum boundary or bleeding channel. The change rate of apparent resistivity could be approximated with the exponential function of rainfall. In such case, the apparent resistivity under most dried condition at the concerned point should be used as reference maximum apparent resistivity. The change rate of apparent resistivity due to rainfall in fracture zone reflects infiltration of stormwater, suggesting to be useful for disaster prevention of slopes. 5 refs., 6 figs.

  12. Decay of 57Ni

    Santos Scardino, A.M. dos.


    The decay of 57 Ni to 57 Co was studied by gamma ray spectroscopy using both singles and coincidence spectra. The sources were obtained with the 58 Ni (Y,n) 57 Ni reaction. Natural metallic nickel was irradiated in the bremsstrahluhng beam of the linear accelerator of the Instituto de Fisica da Universidade de Sao Paulo with 30 MeV electrons. The singles espectra were taken with 104 cc HPGe detector and the coincidences espectra with 27 and 53cc Ge(Li) and 104 cc. HPGe detectors. The energies of transitions that follow the 57 Ni decay were measured using 56 Co as standard (which was obtained by (Y,np) reaction in 58 Ni) and taking into account the cascade cross-over relations. (author) [pt

  13. Natural convection heat transfer in an anisotropic porous cavity heated from the side. 2nd Report. experiment by hele-shaw cell; Tosuiritsu ni ihosei wo yusuru howa takoshitsu sonai no sokuho kanetsu ni yoru shizen tairyu netsu dentatsu. 2. Hele shaw cell ni yoru jikken

    Kimura, S; Okajima, A; Kiwata, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering


    Natural convection heat transfer and flow structure in an anisotropic porous medium of square cavity saturated with Boussinesq fluid has been studied experimentally using a Hele-Shaw cell. The permeability ratio defined by K=K{sub y}/K{sub x} was put to three different values; 0.4, 1 and 2.5. The convection patterns at three different permeability ratios are visualized for several different Rayleigh numbers by the pH indicator method. When K is 0.25, the visualized flow is mainly in the vertical direction. On the contrary for K=4 the convecting flow is in the horizontal direction. The average heat transfer coefficients are also measured, and the corresponding Nusselt number are plotted as a function of K. It is found that the corresponding Nusselt numbers are scaled with (KRa){sup 1/2}. The experimental results of flow pattern and heat transfer are accord with those obtained by our previous theory. (author)

  14. Technology to prevent deposition of marine organisms by means of electrically conductive coating. Discussions on current and potential distribution by using experiments; Doden tomaku ni yoru kaiyo seibutsu fuchaku boshi gijutsu. Denryu den`i bunpu ni kansuru jikken ni yoru kento

    Usami, M; Masaki, T [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Ueda, K


    Steel structures in sea water and surface of hulls are deposited with such marine organisms as microorganisms, algae and shellfish. The deposition causes a large problem such as occurrence of abnormal local corrosion in the structures, and increase in cruising resistance in ocean vessels. The present study has introduced a simplified equation of estimation for current and potential distribution in parts coated with an electrically conductive film, and verified its reasonability by an experiment. The equation of estimation was introduced by following a model of current flow in the electrically conductive coating. The experiment has the conductive coating applied to the interior of a concrete water tank with a length of 10.8 m, a width of 5 m and a depth of 3 m to measure potential at different locations. The conductive coating was energized from copper foils attached on each applied face, whereas the current was applied to two faces between the conductive films as a pair among the four coating applied faces to measure potential in each location. A simulated calculation revealed that the potential range in the depth direction is made smaller if specific resistance of the conductive film is decreased, and made greater if increased. Effectiveness of the equation of estimation was verified by an experiment. This method has provided a prospect of achieving optimization of the specification for application of the conductive film. 2 refs., 7 figs.

  15. Technology for semi-endless use of lubricating oil, no waste oil, improvement of reliability and keeping high thermal efficiency in engines; Jinzo kino seijo gijutsu ni yoru engine oil no han`eikyu shiyo to haiyu zero, oyobi shinraisei kojo to netsukoritsu teika no boshi (joyosha ni yoru shiken oyobi truck ni okeru jitsuyoka)

    Azuma, T [Teikyo University, Tokyo (Japan); Sumimoto, M; Kimura, I


    The authors have developed a new technology which enables it to use lubricating oil almost forever without any waste oil, only compensating lost oil and additives. The system has been working well in many marine and co-generation diesel engines. These engines have been also free from most of engine troubles. This paper reports the test results made on a car and some trucks. Besides above mentioned advantages, the results show that high thermal efficiency has been kept for more than ten years in the car tested and that the exhaust gas brake is much improved in the trucks. 8 refs., 4 figs.

  16. Bridging exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles

    Rinaldi-Montes, Natalia, E-mail: [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain); Gorria, Pedro [Departamento de Física & IUTA, EPI, Universidad de Oviedo, E-33203 Gijón (Spain); Martínez-Blanco, David [Servicios Científico-Técnicos, Universidad de Oviedo, E-33006 Oviedo (Spain); Fuertes, Antonio B. [Instituto Nacional del Carbón, CSIC, E-33080 Oviedo (Spain); Fernández Barquín, Luis [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, E-39005 Santander (Spain); Puente-Orench, Inés [Instituto de Ciencia de Materiales de Aragón, CSIC-Universidad de Zaragoza and Institut Laue-Langevin, BP 156, F-38042 Grenoble Cedex 9 (France); Blanco, Jesús A. [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain)


    Among all bi-magnetic core(transition metal)@shell(transition metal oxide) nanoparticles (NPs), Ni@NiO ones show an onset temperature for the exchange bias (EB) effect far below the Néel temperature of bulk antiferromagnetic NiO. In this framework, the role played by the magnetism of NiO at the nanoscale is investigated by comparing the microstructure and magnetic properties of NiO and Ni@NiO NPs. With the aim of bridging the two systems, the diameter of the NiO NPs (~4 nm) is chosen to be comparable to the shell thickness of Ni@NiO ones (~2 nm). The EB effect in Ni@NiO NPs is attributed to the exchange coupling between the core and the shell, with an interfacial exchange energy of ΔE~0.06 erg cm{sup −2}, thus comparable to previous reports on Ni/NiO interfaces both in thin film and NP morphologies. In contrast, the EB detected in NiO NPs is explained in a picture where uncompensated spins located on a magnetically disordered surface shell are exchange coupled to the antiferromagnetic core. In all the studied NPs, the variation of the EB field as a function of temperature is described according to a negative exponential law with a similar decay constant, yielding a vanishing EB effect around T~40–50 K. In addition, the onset temperature for the EB effect in both NiO and Ni@NiO NPs seems to follow a universal dependence with the NiO crystallite size. - Highlights: • Comparison of the exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles. • Universal temperature dependence of the exchange bias effect. • Suggested similar physical origin of the effect in both systems. • Size and crystallinity of the NiO shell hold the key for exchange bias properties.

  17. Synthesis of calcium-deficient by hydroxyapatite-collage composite by the electrolytic deposition method; Denkai sekishutsu ho ni yoru karushiumu kesson hidorokishiapataito-coragen fukugotai no gosei

    Okamura, H. [Niigata University, Niigata (Japan). Graduate School Of Science and Technology; Yasuda, M.; Oota, M. [Niigata University, Niigata (Japan)


    Hydroxyapatite is known as that it has a good joining property with teeth and bone, and a study on the application to the living body was conducted by using this property. Its application examples were given as the cement used in dentistry, the artificial tooth root, the artificial bone, the bone cement and the artificial joint. However, they were a sinter heated at more than 1000degC, and were put into use by means of reinforcement using a titanium alloy since their mechanical strength was low. In this study, synthesis of calcium-deficient hydroxyapatite (DAp) and collagen composite by the electrolytic deposition method was attempted in order to develop bionic materials, and the correlation of various physical properties of the obtained composite and the electrolytic deposition conditions were investigated. When the electrolytic voltage is more than 22.0V, a single phase of DAp could be obtained. It was clarified that a DAp and collagen composite was synthesized from results of IR and ESR. 16 refs., 5 figs.

  18. Fundamental principles of a new EM tool for in-situ resistivity measurement; Denji yudoho ni yoru den`ichi hiteiko sokutei sochi no kento

    Noguchi, K; Aoki, H [Waseda University, Tokyo (Japan). School of Science and Engineering; Saito, A [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)


    For the purpose of measuring in-situ resistivity without contact with the rock, a study was made about a measuring device using electromagnetic induction. This measuring device has two concentric transmission loops and a receiving point at the center of the loops, and performs focusing by canceling the primary magnetic field at the receiving point. Using this device, a trial was made to eliminate the influence of surface undulation. In the model calculation, response was calculated after the structure with a heavily undulated ground surface was replaced by a two-layer structure with the first layer provided with a higher resistivity. In the model, the first layer had a resistivity of 10000 Ohm m, and the second layer 1000 Ohm m. Using the ratio between the transmission loop radii as a parameter, relationship with the thickness of the first layer was studied, and it was found that the sensitivity to the second layer resistivity increases when the inner and outer loops are nearer to each other in terms of radius and that this eliminates the influence near the surface layer. A decision needs to fall within a scope assuring good reception because response intensity decreases as the ratio between the transmission loop radii approaches 1. 3 refs., 11 figs.

  19. Forward prediction of tunnel face by use of equi-traveltime planes; Tosojimen no riyo ni yoru tunnel kiriha zenpo tansa

    Ashida, Y [Kyoto University, Kyoto (Japan). Faculty of Engineering; Hirano, T [Nishimatsu Construction Co. Ltd., Tokyo (Japan)


    The result is reported herein of a depth transform algorithm application utilizing equi-traveltime planes in reflection seismic exploration for the purpose of knowing the structure configuration in front of the tunnel face in a tunnel excavation process. A vibration producing hole was provided 0.5m above the ground surface while a vibration receiving hole was provided at 1.5m above the ground surface, and the excavated lengths were 1.5m and 0.5m, respectively. There were 24 recording channels, from which inline offset records were taken. The on-site records were subjected to 100-1000Hz band pass filtering. The elastic wave propagation rate in the rock used for depth conversion was set at 400m/s in consideration of the distance and direct wave travel time from the vibration source to the vibration receiving point. As the result of study, weak layers were found in the neighborhood of 230-240m, 260-270m, and 280-290m. This method requires less core memory for calculation and completes calculation in a shorter period of time, which enables a conclusion that it will be effective in grasping the 3-dimensional structure in front of the tunnel face in the working scene. 4 refs., 7 figs.

  20. Simulation on breakage of heterogeneous materials caused by detonative loading; Bakugo shogeki ni yoru fukinshitsu zairyo no hakai gensho no simulation

    Sassa, K; Watanabe, T; Ashida, Y [Kyoto University, Kyoto (Japan). Faculty of Engineering


    Investigations were conducted by simulation of breakage of inhomogeneous materials (rock) attributable to detonative loading, which simulation used the Days-2 Code. During the simulation, one-free-face blastings were used for testing a homogeneous structure, horizontal 2-layer structure, and horizontal 3-layer structure. Property values were assigned to the rocks on the assumption that they were sedimentary rocks such as sandstone or mudstone or hard rocks such as granite. As the result, it was found that a detonative loading resulted in shear failure in a sphere near the focus that was followed by radially developed cracks due to tension breakage, that more area is damaged in a soft rock than in a hard rock, that cracks due to breakage are produced by the overlapping of waves directly from the focus and those reflected from the free face in case of one-free-face blastings, that such cracks propagated along the soft rock layer in case there is a soft rock layer in a hard rock, but that breakage does not extend beyond the soft rock layer. 6 refs., 6 figs., 1 tab.

  1. Estimation of subsurface-fracture orientation with the three-component crack-wave measurement; Kiretsuha sanjiku keisoku ni yoru chika kiretsumen no hoko suitei

    Nagano, K; Sato, K [Muroran Institute of Technology, Hokkaido (Japan); Niitsuma, H [Tohoku University, Sendai (Japan)


    This paper reports experiments carried out to estimate subsurface-fracture orientation with the three-component crack-wave measurement. The experiments were performed by using existing subsurface cracks and two wells in the experimental field. An air gun as a sound source was installed directly above a subsurface crack intersection in one of the wells, and a three-component elastic wave detector was fixed in the vicinity of a subsurface crack intersection in the other well. Crack waves from the sound source were measured in a frequency bandwidth from 150 to 300 Hz. A coherence matrix was constituted relative to triaxial components of vibration in the crack waves; a coherent vector was sought that corresponds to a maximum coherent value of the matrix; and the direction of the longer axis in an ellipse (the direction being perpendicular to the crack face) was approximated in particle motions of the crack waves by using the vector. The normal line direction of the crack face estimated by using the above method was found to agree nearly well with the direction of the minimum crust compression stress measured in the normal line direction of the crack face existed in core samples collected from the wells, and measured at nearly the same position as the subsurface crack. 5 refs., 4 figs.

  2. Subsurface geology by shallow seismic reflection survey and microgravity survey in Kobe area; Senso hanshaho danseiha tansa oyobi seimitsu juryoku tansa ni yoru Kobe chiiki no chika chishitsu

    Endo, H; Makino, M; Murata, Y; Watanabe, S [Geological Survey of Japan, Tsukuba (Japan)


    This paper reports discussions on subsurface structure of the Kobe area by means of microgravity survey. A Bouguer anomaly distribution graph was obtained (which is close to a near straight line) by measuring the gravity at measurement points with an interval of about 25 m along a traverse line (with a total length of about 1.7 km) in an approximately NNW-SSE direction crossing the downtown of the city of Kobe. Viewing the residuals to a straight line linking the values at both ends of the traverse line revealed that the gradient in the Bouguer anomaly distribution changes as if it is bent at a point near the center of the traverse line as a boundary. Deriving the residuals from fine changes seen in a distribution graph for the residuals made clear that this residual distribution has two discontinuous points. The paper indicates that the bending point in the former case corresponds to a reverse fault in a base bed of a flat land as compared with the result of model calculation on the base structure and gravity distribution. The discontinuous points in the latter case agree with positions of fault distribution derived by a reflection elastic wave survey. 6 refs., 4 figs.

  3. Development of the electromagnetic tomography system. Field test results using existing equipment; EM tomography system no kaihatsu. Kison sochi ni yoru test sokutei kekka

    Kumekawa, Y; Miura, Y; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Arai, E [Metal Mining Agency of Japan, Tokyo (Japan)


    With the purpose of developing an electromagnetic tomography system, an observation was carried out with existing equipment combined, and the data was analyzed. The measuring equipment consisted of existing borehole vertical magnetic field sensors as the sensor part, MT method receivers as the receiving device, and existing CSMT method transmitters as the transmitting device. The measuring was performed at the Richmond Field Station which was abundant in existing data and which had a comparatively simple resistivity structure. The borehole vertical magnetic field sensors were lowered inside the borehole, and signal sources were arranged at 10m apart on the traverse line in the direction from northeast to southwest with the borehole as the center. The analysis of the data was made with the use of EM1D by three models, namely, 10 ohm{center_dot}m homogeneous earth model, 100 ohm{center_dot}m homogeneous earth model, and horizontal 7 layer model prepared on the basis of electric logging results; and a comparative examination was made against the measured data. As a result, it was demonstrated that the test measurement agreed very well with the model from the electric logging results and that it was the data reflecting a resistivity structure. 8 refs., 6 figs.

  4. Development of the electromagnetic tomography system. Sensitivity study of anomalous body by model studies; EM tomography system no kaihatsu. Model kaiseki ni yoru ijotai no kando chosa kekka

    Kumekawa, Y; Miura, Y; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Arai, E [Metal Mining Agency of Japan, Tokyo (Japan)


    An examination was made by a model analysis on sensitivity and the like against a resistive anomalous body, in connection with an electromagnetic tomography system with surface earthquake sources and underground receiver arrangements. A resistivity model was of a three-dimensional structure, and built with a 5 ohm{center_dot}m low resistivity anomalous body assembled in a 100 ohm{center_dot}m homogeneous medium. As a result of the examination, it was shown that the size limitation of an analyzable anomalous body was 50{times}50{times}20m at a frequency of 8 to 10kHz and that a system with high precision in a high frequency range was necessary. The examination of effects under a shallow anomalous body revealed, for example, that the fluctuation of a low frequency response was large compared with a deep anomalous body and that, where a second anomalous body existed under it, the effect also appeared with a surface earthquake source positioned in the opposite side from the anomalous body. The examination of effects under the three dimensional structure revealed, for example, that a remarkable change appeared in the data with the change in the inclined angle of the transmission line against the strike of the anomalous body. 4 refs., 7 figs.

  5. Load leveling by a battery system in an electric power system with a photovoltaic system; Taiyoko hatsuden system ga donyusareta denryoku keito no chikudenchi ni yoru fuka heijunka

    Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)


    Storage battery-aided load leveling system is introduced into a power system having a photovoltaic power generation (PV) system, and the effect of the introduction is examined. For this purpose, the resultant improvement on the load factor and reduction in the annual cost are evaluated. Used as the load factor in the studies are the hourly records of power transmitted and received by Chubu Electric Power Co., Inc., in 1995. The output of the PV system is calculated using weather data collected in Nagoya City in the same year. Findings as the result of the studies are stated below. The maximum power is suppressed but a little if it is only the PV system that is introduced into the system. That is, a 2GW PV system introduced into the system suppresses the maximum power only by 0.5GW or less. The maximum power is suppressed more effectively when a storage battery is added, and it decreases linearly with an increase in the storage battery capacity. As for reduction in the cost, the reducing effect is higher when the rate of storage battery capacity/introduced PV capacity is higher in the presence of an introduced PV capacity of 0.8GW or more. 2 refs., 7 figs., 3 tabs.

  6. Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

    Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)


    Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

  7. Photogrammetric measurement of two-dimensional small-amplitude waves; Hakuso suiryu no nijigen bisho shinpukuha no shashin sokuryoho ni yoru sokutei

    Yoshino, F. [Tottori University, Tottori (Japan). Faculty of Engineering; Urata, K. [Hitachi Zosen Corp., Osaka (Japan); Kishi, H.


    A photogrammetric measurement method for two-dimensional small-amplitude waves were proposed where a diffuse reflection spot is used as an index point. An equation used to obtain the still water depth was introduced. This equation was confirmed experimentally by using a laser displacement sensor which is equivalent to a camera-index-point system in principle. To confirm the applicability of this method to waves form measurement, numerical simulations of measurement by this method were carried out for sinusoidal waves and a composed wave. The results of these simulations show that the small-amplitude waves can be measured with sufficient accuracy when the water surface inclination is small. 4 refs., 14 figs., 1 tab.

  8. Three component particle velocimetry using laser sheets for cycle-resolved, in-cylinder measurements; Laser sheet ho ni yoru cylinder nai nagare no sanjigen sokutei

    Ishii, K.; Urata, Y.; Yoshida, K.; Ono, T. [Honda Motor Co. Ltd., Tokyo (Japan)


    Analysis of the cycle-by-cycle variation of combustion in an internal combustion engine can be aided by the cycle-resolved measurement of the in-cylinder gas velocity. This paper describes the principle and operation of, and results obtained from, a particle coded-pulse velocimeter (PCPV) which measured the three components of velocity within normal planes to the axis of cylinder. The PCPV was applied to a 1.5 litre lean-burn engine in order to record the flow pattern. The intake air was seeded with light microcapsules of approximately 50{mu}m diameter which scattered light from a system of up to two sets of three plane laser sheets, distinguished by colour and thickness and pulsed by acousto-optic modulators, illuminating planes in the bore of the engine. The magnitudes of the axial and cross bore components of the velocity vector were found from the measured lengths and the duration of the particle tracks. The results from the PCPV measurements are time-resolved and instantaneously three-dimensional and thus the PCPV is capable of identifying the transition from a disordered flow, such as the intake process, to well-ordered flows such as occur during a compression process. The derived swirl and tumble ratios were relatively in good agreement with those measured by an impulse swirl meter. 6 refs., 8 figs., 1 tabs.

  9. Ion exclusion chromatography for the purification of L-glutamine; Ion haijo chromatography ni yoru L-glutamine no seiseiho no kenkyu

    Ito, H.; Nishi, A.; Naruse, M. [Ajinomoto Co. Inc., Kawasaki (Japan)


    Ion exclusion chromatography for the purification of L-glutamine is studied. L-glutamine is usually produced by fermentation and used in pharmaceuticals. By using a model solution of L-glutamine and L-glutamic acid, the optimum cation exchange resin is examined. As a result of the experiments, it is found that a cation exchange resin which has smaller crosslinkage and smaller diameter is better. Ammonium sulfate, L-glutamic acid and pyrrolidonecarboxylic acid, which are usually contained in fermentation broth as impurities, are effectively separated by this method. Moreover, the experimental data of the chromatography is expressed fairly well by the differential equations which express the mass transfer in the fixed bed. 8 refs., 5 figs., 2 tabs.

  10. On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

    Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)


    Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

  11. Aerodynamic characteristics of a wing near its tip using panel method. Panel ho ni yoru tandokuyoku yokutan fukin no kuryoku tokusei

    Choi, J [Nagoya University, Nagoya (Japan); Sugiyama, Y [Nagoya University, Nagoya (Japan). Faculty of Engineering


    The study described in this paper is intended to evaluate the aerodynamic characteristics of a turbo machine wing or an aircraft wing near its tip, using the panel method. The paper describes the case of a rectangular wing with a large aspect ratio. The introduced linear simultaneous equation was solved using a computer, and compared with the experimental result. The result may be summarized as follows: The distribution of pressure on the wing near its tip using the panel method takes the same shape as that for the experimental result; the negative pressure calculated close to the wing's trailing edge near the wing tip is a result of a three-dimensional effect of the flow along the wing width; the calculation and the experiment showed an increase in local lift coefficient and locally induced resistance coefficient in the vicinity of wing tip; the speed component in the y'' direction explains the structure of the wing surface velocity forming wing backwash vortex given by the lift linearity theory; and the result of calculation on the pressure distribution in the wing chord direction near the wing tip is very close to the experimental result except for the wing flank in the close vicinity of the wing tip upstream of the wing chord middle point. 11 refs., 13 figs.

  12. Estimation for origin of coals on biomaker analysis; Jinko sekitan oyobi tennen sekitan no biomaker bunseki ni yoru sekitan kigen busshitsu no suitei

    Suzuki, Y. [Geological Survey of Japan, Tsukuba (Japan); Sugimoto, Y. [National Institute of Materials and Chemical Research, Tsukuba (Japan); Okada, K. [Coal Mining Research Center, Tokyo (Japan)


    In order to study coal production processes, an estimation study was carried out on coal originating materials by using biomaker analysis. Test samples are original coals collected directly from a mine in Hokkaido (not having been subjected cleaning). Mixing and solvent extraction were performed after pulverization, and then tests were given on saturated hydrocarbon components divided by using a silicagel column chromatograph for the present study. It can be known from n-alkane distribution in the coal that low molecular alkane increases with increasing degree of coalification. Artificial coal made by wet-heating Metasequoia leaves contains only little n-alkane. Diterpenoid compound exists in the Taiheiyo and Akabira coals. Tetra-cyclic diterpernoid is contained abundantly in subtropical coniferous trees, serving as a parameter for warm environment. The compound is contained also in the Fushun coal, but not in Indonesian coals. Hopanoid constitution shows very high similarity, but H/C atomic ratio may vary largely even if the coalification is at the same degree. This is likely to be caused from difference in originating materials. Hopanoids are bacteria attributed substances, whose activities are not affected by the originating materials. 2 figs., 1 tab.

  13. Explosive treatment of Illinois No.6 coal with a mixed solvent of water and cyclohexanol; Mizu-cyclohexanol kongo yozai ni yoru Illinois tan no bakusai shori

    Hashimoto, T.; Takada, H.; Asami, K.; Yano, M. [Osaka City University, Osaka (Japan). Faculty of Engineering


    Coal was treated at high temperature under high pressure in the binary system mixed solvent of water and organic solvent, and the solvent treated coal was liquefied. When the treated coal was treated again by the explosive method in which high temperature and pressure were released immediately, the oil yield was higher than that by the normal method in which high temperature and pressure were reduced gradually to room temperature and atmospheric pressure. In this study, an explosive treatment unit with increased scale of sample amount was newly fabricated. Illinois No.6 coal was treated by the explosive method in a mixed solvent of water and cyclohexanol using this unit. Changes in shape on the surface, specific surface area, and functional groups were analyzed. The explosively treated coal contained more amount of low boiling point components than the normally treated coal. It was suggested that the oil yield of explosively treated coal increased due to the liquefaction of these components during the successive hydrogenation process. For the explosively treated coal, micro pores were fractured by the rapid change in the volume of solvent molecules, and the specific surface area was smaller than that of the normally treated coal. When the treatment temperature was increased from 300{degree}C to 350{degree}C, specific surface areas of both the treated coals increased. 2 refs., 3 figs., 2 tabs.

  14. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)


    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  15. Depolymerization of coal by O2 oxidation followed by acid hydrolysis; Sanso sanka-kasui bunkai ni yoru sekitan no teionkai jugo

    Aizawa, S.; Hayashi, J.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    With an objective to elucidate characteristics of oxygen addition to coal, and characteristics of solvent extraction by means of depolymerization, experiments were performed on oxygen oxidation and acid hydrolysis of brown coals. Coals used for the experiments are Morwell (MW), Yallourn (YL) , South Banko (SB) and Wyoming (WY) coals. Test samples were suspended in weak alkaline aqueous solution, and then oxygen was blown into them with pressure kept at atmospheric pressure. After a lapse of a predetermined time, the samples were cooled, and made as acidic as pH 1.3 in hydrochloric acid, followed by acid hydrolysis. Oxygen consumption increased with the reaction time, and with the MW coal, one mol oxygen reacted to 11 mols of coal. Spectral analysis on the YL and WY coal experiments revealed that aliphatic carbon combined with aromatic carbon or ether group has turned to peroxide, whose C-C or C-O bond was broken down as a result of acid hydrolysis of the peroxide, producing oxygen containing compounds. As a result of the depolymerization, the rate of extraction by using DMF, DMSO and methanol/THF mixed solvent increased to 90% or higher. Proportion of bond and cutting-off affects largely collapse of the cross-link structure. The carbon conversion to volatiles was at most 4%. 1 ref., 10 figs.

  16. ESR study on the interaction between carbon blacks and oxygen molecules; ESR ho ni yoru carbon black to sanso bunshi tono sogo sayo no kenkyu

    Okazaki, M.; Toriyama, K.; Konishi, Y. [National Industrial Research Institute of Nagoya, Nagoya (Japan)


    Interaction between carbon blacks and oxygen molecules has been studied by means of electron spin resonance (ESR) spectroscopy. The ESR spectra of the carbon blacks appears at the g-value of free spin, which are contributed by both isolated electrons and conduction electrons. Upon introducing oxygen to the system the ESR linewidth was broadened in proportion to the partial pressure of oxygen. In case of lampblack (LB 101, Degussa) the interaction was not so strong that it took a tong time at 77K for the linewidth to reach the maxmum value. In case of gassblack (P 140 V, Degussa), on the other hand, the oxygen was easily adsorbed at 298K and the linewidth at 77K became its maximum immediately after cooling. The number of unpaired electrons decreased when the system was kept at 298 K and the decrease was prominent for the local spins. These phenomena have been explained with a simple band model for the electron. (author)

  17. Preparation of tazheranite powders by solid phase reaction and conductivity of sintered bodies. Kosoho ni yoru tazheranite no funmatsu gosei to dodensei

    Kuramochi, H; Kobayashi, H; Mitamura, T [Saitama University, Saitama (Japan). Faculty of Enginering; Mori, T; Yamamura, H [Tosoh Co., Tokyo (Japan)


    Single phase powder of Ca0.2Zr(0.8-x)TixOy was synthesized by replacing a part of ZrO2 in tazheranite which belongs to cubic crystal mineral of 3 constituents of CaO/ZrO2/ TiO2 with TiO2 to study the conductivity. Predetermined powder amounts of CaCO3, ZrO2 and TiO2 were respectively weighed and mixed with wet condition, the carbonate was decomposed at 1,000 centigrade, and after mixed again with wet condition, the mixture was dried and calcined again at 1,200 to 1,300 centigrade for 2 to 20 hours to get the powder. This powder was crushed and classified to make molded items by uniaxial pressing and the items were fired at 1,400 to 1,600 centigrade for 1 to 10 hours. The conductivity of sintered bodies was measured by the complex impedance method. The following results could be obtained: The targeted powder could be synthesized at the composition range of x=0.04 to 0.10 and the apparent x of single phase area was widened to 0.15 at the firing temperature of 1,500 centigrade. The activation energies of the conductivity of sintered items were 120 to 130kJ/mol, indicating that the electric conductivity was dominated by the ion conduction and was not affected by TiO2 amount, and the formed phase. The grain resistance increased and the grain boundary resistance decreased with the increase of TiO2 amount. 17 refs., 9 figs.

  18. Surface wettability control by titanium dioxide photo-induced reaction. Super-hydrophilic properties; Sanka chitan ni yoru hikari reiki shinsuika gijutsu. Hikari shokubai chosinsuisei

    Watanabe, T. [The University of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology


    Hydrophilicity results when the surface of titanium dioxide is reduced for the specified oxygen to be replaced by hydroxyl groups. The ease with which such a structural change occurs is subject to variation between titanium dioxide crystal surfaces, and is dependent greatly on the atmosphere. No hydrophilic trend is observed in an atmosphere of oxygen only without moisture and, in darkness without light, hydrophobicity occurs early. Although the contacta angle titanium dioxide with water with stability is not known, yet it is presumed, on the analogy of the case of strontium titanate, that it is in the range of 20-40 degrees. A hydrophilic trend below the range is attrributed to structural changes. The control of surface wettability is one of the basic tasks to fulfill in various kinds of mechanisms and manufacturing processes. The technology of wettability control using a titanium dioxide coating which is quite durable will be applied not only to functions involving defogging, dripproof, and self-cleaning, but also to the control of heat transmission in the mechanism and to the bonding process. (NEDO)

  19. Numerical simulation of an excited round jet under helical disturbances by three-dimensional discrete vortex method; Helical kakuran ni yoru reiki enkei funryu no uzuho simulation

    Izawa, S.; Kiya, M.; Mochizuki, O. [Hokkaido University, Sapporo (Japan)


    The evolution of vortical structure in an impulsively started round jet has been studied numerically by means of a three-dimensional vortex blob method. The viscous diffusion of vorticity is approximated by a core spreading model originally proposed by Leonard (1980). The jet is forced by axisymmetric, helical and multiple disturbances. The multiple disturbances are combinations of two helical disturbances of the same mode rotating in the opposite directions. The multiple disturbances are found to enhance both the generation of small-scale structures and the growth rate of the jet. The small-scale structures have highly organized spatial distributions. The core spreading method is effective in aquiring the core overlapping in regions of high extensional rate of strain. 21 refs., 12 figs.

  20. Control of population of excited nitrogen molecules by mixing hydrogen in low pressure discharge; Chisso jun`antei reiki bunshi mitsudo no quenching ni yoru seigyo no kento

    Uematsu, K.; Yumoto, M.; Sakai, T. [Musashi Institute of Technology, Tokyo (Japan)


    The authors have studied on surface treatment of PTFE by a low pressure discharge. It is deduced that excited nitrogen molecules contribute to introduce polar components on the surface. To confirm the speculation, we tried to change population of metastable nitrogen N2 (A{sup 3}{Sigma}u{sup +}) by quenching precursor N2 (B{sup 3}{pi}g), with hydrogen molecule. The decrease of relaxation time which indicates a change of excited molecule and measured by emission spectroscopy using a time after glow method was obtained. As a result, the relaxation times of N2 (B{sup 3}{pi}g) and N2 (A{sup 3}{Sigma}u{sup +}) decreased to 55% and 20% respectively, when mixing ratio of hydrogen was 3%. It was also deduced that hydrogen atom may take a part in a quenching process of N2 (A{sup 3}{Sigma}u{sup +}). 14 refs., 11 figs., 1 tab.

  1. Surface wettability control by titanium dioxide photo-induced reaction. Super-hydrophilic properties. Sanka chitan ni yoru hikari reiki shinsuika gijutsu. Hikari shokubai chosinsuisei

    Watanabe, T. (The University of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology)


    Hydrophilicity results when the surface of titanium dioxide is reduced for the specified oxygen to be replaced by hydroxyl groups. The ease with which such a structural change occurs is subject to variation between titanium dioxide crystal surfaces, and is dependent greatly on the atmosphere. No hydrophilic trend is observed in an atmosphere of oxygen only without moisture and, in darkness without light, hydrophobicity occurs early. Although the contacta angle titanium dioxide with water with stability is not known, yet it is presumed, on the analogy of the case of strontium titanate, that it is in the range of 20-40 degrees. A hydrophilic trend below the range is attrributed to structural changes. The control of surface wettability is one of the basic tasks to fulfill in various kinds of mechanisms and manufacturing processes. The technology of wettability control using a titanium dioxide coating which is quite durable will be applied not only to functions involving defogging, dripproof, and self-cleaning, but also to the control of heat transmission in the mechanism and to the bonding process. (NEDO)

  2. Analysis of combustion in an ATAC engine with measurement of radical luminescence; Radical hakko keisoku ni yoru ATAC engine no nensho kaiseki

    Park, Y; Oguma, H; Ueda, H; Iida, N [Keio University, Tokyo (Japan)


    In order to make clear of the combustion mechanism and the frame structure in two stake, so called, active thermo-atmosphere combustion (ATAC) engine fueled by gasoline and methanol, we measured the 2-demensional images of OH, CH and C2 radical band spectra in both ATAC and SI combustion mode. From the results of pressure data in the cylinder, the heat release rate was calculated. We evaluated the correlation of radical luminescence intensity and the rate of heat release. 3 refs., 4 figs., 2 tabs.

  3. Quantitative measurements of air-fuel mixture distribution in a cylinder using LIF; LIF ni yoru tonai kongoki nodo no teiryoteki keisoku

    Kato, S; Kadoi, N [Subaru Research Center, Tokyo (Japan)


    It is necessary to understand the mechanisms of mixture formation in a cylinder to improve engine performance, especially for a gasoline direct injection engine. In this study, a quantitative air-fuel mixture measurement technique using PLIF was developed. Across a laser sheet, a transparent liner was placed between two calibration cells which increased the reliability of fuel concentration. This technique was applied to gasoline direct injection engine to clarify the effect of injection timing on stratified charged mixture. 4 refs., 6 figs., 3 tabs.

  4. Basic study on mass transportation systems in buildings by means of multiple-cage elevators; Junkangata erebeta ni yoru biru nai tairyo yuso sisutemu no kiso kento

    Fujino, A.; Tobita, T. [Hitachi, Ltd., Tokyo (Japan); Nakagawa, K. [Shimizu Corporation, Tokyo (Japan)


    From the viewpoints of realization of mass transportation, improvement of space factor in buildings, transportation systems in buildings are surveyed to compare the characteristics. Then, a loop-type independently-driven multiple-cage elevator (circulating elevator) system is proposed to estimate its transportation capacity, and necessary data for realizing transportation capacity higher than twice that of the conventional elevator are presented. As regards operational control, a high efficient control method is proposed which can restrain needless stops particular to the multiple-cage system and improve the waiting time and round trip time, and the result of the investigation by simulation is reported. Basic operation method of the loop-type elevator is determined, and the transportation capacity is estimated by simulation. The application in which the loop-type elevator can exhibit the best performance is its use in 15 floor-class buildings or for local bank zones in large-scale buildings in a system combined with the shuttle system. 9 refs., 12 figs., 5 tabs.

  5. Insulation diagnosis of rotating machines for elevators by an expert system based on fuzzy inference. Fuzzy suiron wo donyushita expert system ni yoru shokokiyo kaitenki no zetsuen shindan

    Kaneko, K.; Oshima, H. (Tokai Univ., Tokyo (Japan)); Yamada, N.; Iijima, T. (Mitsubishi Electric Building Techno-Service Co. Ltd., Tokyo (Japan))


    Using the data measured with the insulation deterioration diagnostic system for rotating machines for elevators, which is newly developed utilizing the past experience, an expert system which enables insulation deterioration diagnosis even by field maintenance engineers to some extent. In this system, the knowledge and experience of specialists are loaded in a personal computer as the rule for insulation deterioration diagnosis to perform insulation deterioration diagnosis by fuzzy inference and 'hypothesis-verification' type backward reasoning inference. The structured expert system is outlined. The result of insulation diagnosis by this system s compared with that made by specialists to evaluate the effectiveness of the diagnosed result of this system, and shows 84% agreement with the results obtained by specialists. It is, therefore, considered to be a highly practical expert system. 10 refs., 7 figs., 1 tab.

  6. Reinforcing method for reinforced concrete structures by using carbon fibers; Tanso sen`i ni yoru tekkin concrete kozobutsu no hokyo koho

    Tanaka, T.; Taniki, K. [Mitsubishi Kasei Corp., Tokyo (Japan); Kojima, N.; Kimura, K.; Katsumata, H. [Obayashi Corp., Osaka (Japan)


    This paper describes the development of a reinforcing method for reinforced concrete (hereinafter RC) structures by using carbon fibers (hereinafter CF). This developed method attaches a light-weight CFUD prepreg material for reinforcement by laterally winding CF strand impregnated with epoxy resin, which is hardened under normal temperature. This method is economical because no skills and special tools are required. An RC pillar with circular cross section and a hollow RC test body assuming a chimney were used as models. The paper details the experiment. This method has been used in several ten existing RC stacks with effective reinforcing result. Resistance strengths of CF strands and UD prepregs were verified in an accelerated exposure test performed according to JIS A 1415, standard for plastic building materials. The effects of the anti-seismic reinforcement have resulted in improvement in shear resistance force in RC pillars by means of CF winding method, improvement in bending stress in RC structures as a result of CF attaching method, and effectiveness in repair of existing RC stacks. Sufficient exposure resistance has also been proved. A bending test by means of two-point concentrated loading has been performed as a weighted test. 4 figs.

  7. Corrosion prevention of the rail by thermal spray coating of Zn-Al alloy; Zn-Al gokin yosha hifuku ni yoru reru no boshoku

    Mizoguchi, S. [Nippon Steel Corp., Kitakyushu (Japan)] Urashima, C. [Kyushu Techno Research Corp., Fukuoka (Japan); Itai, K. [Nippon Steel Corp., Kitakyushu, Fukuoka (Japan). Technical Research Inst. of Yawata Works; Ichiriki, T.; Nishiki, M. [Kyushu Rail way comdany, Fukuoka (Japan)


    Replacement of the rail in under-sea tunnel such as the Kammon Tunnel is carried out very five years because of the severe corrosion caused by the humid state due to the leakage of sea water or the mist of sea water swept up by the passing trains. In this study, salt water spraying or sea water spraying test is carried out using Zn-Al alloy with the corrosion resistance and thermal spray efficiency even higher than those of Zn or Al. A rail coated by thermal spray of Zn-15mass%Al alloy has been laid by trial in the practical rail road of Kammon Tunnel for 5 years and 3 months, the deterioration degree of the coating, pitting depth, actual fatigue strength, etc. are evaluated. Further, these factors of a rail re-coated by Zincrich Primer+Tar Epoxy and a bare rail laid at the same time are evaluated for comparison. It is presumed by the results of the examination about the service life of a rail coated by the thermal spray of Zn-Al alloy based on the pitting depth in the rail base that the service life of such coated rail is more than twice as that of the bare rails used currently. 5 refs., 14 figs., 3 tabs.

  8. Finite-volume simulation of the flow around a sailing boat with unsteady motion; Hiteijo undo wo okonau hansotei no yuten taisekiho ni yoru simulation

    Akimoto, H. [Tottori University, Tottori (Japan). Faculty of Engineering


    A new simulation code WISDAM-7 is developed to simulate performance of a sailing boat moving three-dimensionally on a free surface. It adequately predicts forces acting on each element, such as hull, sail, keel and rudder, and use them as the inputs to solve equations of hull motion of 6 freedoms. Its major features are the grid system fit for both free and hull surfaces, generation of discrete space by the finite-volume method, handling of the velocity vectors directly as those in the Descartes system, velocity and pressure placed at the cell center, use of the moving grid system for free and object surfaces, and use of equations of hull motion of 6 freedoms. It is confirmed by comparing simulated motion of an IACC class yacht with the observed surface pressure distributions in the test tank that the new method satisfies the basic requirements for simulation of sailing boat motion and expands the applicable range of CFD to general motion conditions. 8 refs., 18 figs.

  9. Method for solving an inverse problem of wing type by using a simple panel method; Kanbenna panel ho ni yoru yokugata gyaku mondai no ichikaiho

    Ando, J; Matsumoto, D; Maita, S; Nakatake, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    This paper describes one method for solving an inverse problem of wing type based on the source and quasi continuous vortex lattice method (SQCM) in designing marine propellers and underwater wings. With the SQCM, vortices and control points are distributed on wing camber according to the QCM, and wing surface is divided into certain number of panels. This is the method to decide vortex intensity and blow-out intensity simultaneously from the condition that vertical speed on the camber and the wing surface is zero, upon having distributed blow-out with certain intensity inside the panel. The method solves the inverse problem with the following process: specific point distribution is so determined that the targeted velocity on the wing surface is satisfied when wing surface pressure distribution and uniform flow velocity are given; and then the panels are so rearranged as in parallel with direction of the flow on the surface of the wing calculated by using these specific points to derive the targeted wing shape. This paper describes the problem solving procedure in great detail. It also introduces examples of numerical calculations. It shows one method for solving the inverse problem in wing type using the SQCM as a simple panel method, whereas its good convergence and stability were verified. Considerations on effects of free surface and expansion of the method into three-dimensional problems will be implemented in the future. 11 refs., 8 figs.

  10. Method for calculating wave resistance in a catamaran by using a simple panel method; Kanbenna panel ho ni yoru katamaran no zoha teiko keisanho

    Kataoka, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    This paper describes a method for calculating wave resistance in a catamaran by using a simple panel method. Two Wigley models were put side by side to make a catamaran, speccular images were taken on a face symmetrical in the left and right sides, and only one side (the demi-hull) was used as a region to be calculated. Considering blow-out onto the demi-hull surface and still water surface, a model was constituted, in which discrete vortices were distributed on the demi-hull camber to flow the vortices out to an infinitely distance place from the stern. A free surface condition according to double model linearization by Dawson was derived for this model in terms of numerical analysis. The Kutta`s condition is incorporated when SQCM is used concurrently with the Rankine source method, but not incorporated when not used. Calculations were performed on both conditions. Wave resistance was derived by using pressure integral on the hull surface. It is better to consider the Kutta`s condition when the distance between the demi-hulls is small. However, if the distance is large, or speed is great for the boat length resulting in less interference between the demi-hulls, there is very little difference due to the Kutta`s condition. Difference in the wave shapes causes how waves are made to vary. 11 refs., 8 figs.

  11. FY1995 studies on saving energy by use of nitrogen- fixing bacteria; 1995 nendo chisso koteikin no katsuyo ni yoru sho energy no kenkyu



    To save energy by improving the ability of nitrogen-fixing bacteria (Kebsiella oxytoca, Azospirillum lipoferum and Sphingomonas paucimobilis) in the rhizosphere of rice, by means of genetic analysis and engineering of the nif genes. Analysis and improvement of the nif genes were performed in 3 species of nitrogen-fixing bacteria in the rhizoshere of rice. (1) In an facultative anaerobe, K. oxytoca, the repressor gene, nifL was destroyed, and the activator gene, nifA was fortified, to attain a novel mutant strain R16, which fixes nitrogen even in the presence of NH{sub 4}{sup +}. (2) In a microaerophilic nitrogen fixer, A. lipoferum, the regulatory genes draT and draG were cloned and analysed, and an improved strain TA1 was obtained by introduction of K. oxytoca nifA gene. (3) In an aerobic nitrogen-fixer S. paucimobilis, the nifA gene was cloned and sequenced, and the activity was expressed in E. coil to show that the product activates the nif promoters of Azospirillurn and Klebsiella. (4) The improved strains K. oxytoca R16 and A. lipoferun TA1 were inoculated to rice plant cultured in a pot without addition of nitrogen source. The inoculated plant showed twice as much dry weight as the noninoculated plant, showing that the improved strains are effective to stimulate the growth of rice. (NEDO)

  12. Optimal control of aerobic bacteria fermentaion by dynamic programming method. Doteki keikakuho ni yoru kokisei saikin hakko process no saiteki seigyo

    Kidoushi, H; Murayama, S; Shiomi, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Haneda, K; Yamada, Y [Asahi Chemical Industry Co. Ltd., Tokyo (Japan)


    A dynamic programing method was applied for maximizing a production yield in controlling the process of aerobic bacteria fermentation. An optimal control was carried out by air flow rate under a sufficient sugar supply condition, using the bacteria amount as a state variable and the air flow rate as an operation variable, under conditions where the sugar consuming rate is not a limiting factor. The growth and production were modelled, and the relationship of both the specific growth rate and the specific production rate to the specific respiration rate was was expressed as functional tables. A simulation was carried out, which provided an optimum air flow pattern. This relationship between the bacteria amount and the optimum air flow rate was mapped to perform a map control. Conditions other than the air flow pattern were made to agree with the previous empirical cultivation method, and experiments were conducted using a cultivation tank of 0.03 m {sup 3}. A yield increase of 13.6% over the conventional method was attained, thus the reasonability of the modelling was verified. It was found that there are portions where the width of the optimum air flow control is wide and narrow, and it is possible to reduce the number of maps if this this is taken into account. 4 refs., 8 figs., 2 tabs.

  13. Evaluation of water content in rock mass by electromagnetic and resistivity tomography. Denjiha, hiteiko tomography ni yoru ganban no gansui jotai hyoka

    Inaba, T; Inoue, M; Matsumoto, K [Kajima Corp., Tokyo (Japan)


    As a method to evaluate the rock mass, electromagnetic tomography and resistivity tomography were tested on the original site. The electromagnetic tomography can tomographically analyze the propagation velocity and initial amplitude damping. The resistivity tomography uses a finite element method from the initial resistivity distribution model and finally gives a model which is nearly equal to the actual resistivity distribution. Both the above tomographic analyses can detect the crushed spot as a low velocity, high damping and low resistivity spot. However, the electromagnetic tomography could detect finer structure than the resistivity tomography. The water content of rock mass was evaluated from the damping coefficient which was given by the amplitude damping tomography of electromagnetic wave. If it is compared with the water content which is given by the dielectric constant of velocity tomography, there partially exists discrepancy between both, because the damping coefficient contains information on cracks which disperse and reflect the electromagnetic wave. Between the resistivity and porosity, there exists a known experimental formula, which was satisfied by the presently given resistivity. 9 refs., 10 figs.

  14. New computational and experimental stress analysis method for the design decision on optimum piston configuration. Piston oryoku no computer simulation to shinshikenho ni yoru keijo saitekika

    Anno, N; Sugita, J [Honda R and D, Co. Ltd., Saitama (Japan)


    Piston troubles are mostly caused by cracks generating in each part of a piston. The finite element method (FEM) has been used for stress analysis of the piston, but has not been applied enough to design optimum configurations due to too much time for making models. In this study, stress analysis was carried out by the boundary element method (BEM), with which it is easy to make models and to change configurations, with various improvements. In addition, methods to execute a thermal load fatigue test and an actual running test to confirm analytical results were also improved. BEASY was used as basic software for analysis by BEM, and some improvements such as reduction of CPU time and optimization of memory using methods were carried out. It was easy to change configurations of the models by BEM, and the effect of the change in the piston boss configuration upon the stress agreed well with the actual test result. Design and evaluation of the optimum configuration has become easier by feedback of the results of the newly developed thermal load fatigue test to the analysis by BEM. 5 refs., 12 figs., 2 tabs.

  15. Fabrication of low cost high performance large size composite structures by electron beam curing (EBC); Denshisen koka (EBC) ni yoru tei cost koseino ogata fukugozai kozo no seizo

    Kamimura, K.; Parrot, P.


    This article introduces the electron beam curing (EBC), which is high speed non-heating cure technique for the high performance resin for structures, conducted by Aerospacial Co., Ltd. In this technique, very strong electron beam and X-ray are used in response to the thickness of curing region of members, and the muzzle has energy of 10 MeV as permeation control energy and power of 20 kW as cure time control power. Advantages of fabrication of composite products by EBC is derived from the elimination of exoergic and heating curing processes and the local cure molding. For the EBC, the residual stress is not generated, the size is stable, the insertion of different materials is easy without mismatch of thermal expansion between the composites and metals, the homogeneous bridge can be obtained to stabilize the material quality, the processing time can be shortened, it is suitable to mass production, and the cure of products can be controlled. About 30% to 40% of the cost of products can be reduced. 1 ref., 6 figs., 1 tab.

  16. Investigation on flow pattern by submersible mechanical aerator aused in anaerobic-aerobic tank. Kenki koki ken'yo suichu aerator ni yoru sonai ryudo no chosa kensho

    Ogasawara, M; Inoue, H; Kamei, T; Kato, N [Ebara Corp., Tokyo (Japan)


    As explained in the present report, flow pattern was verified in a submersible aerator tank for both anaerobic and aerobic wastewater treatment (submersible plant for the mechanical agitation and aeration). The verification was made in a water passage of the sewage treatment plant. The flowing was conditioned as per the measurement of both flow velocity and activated sludge concentration. The submersible aerator was installed so that balance might be kept in ventilating pressure between it and the diffusing plate. The flowing on the tank bottom was stabilized by installing a special guide at the outlet of aerator. The result was as follows: in both tanks during the anaerobic operation, the flow velocity was 0.15m/s as a whole and higher than the standard of 0.1m/s on the tank bottom. Under the tank top and at the middle of tank height, the flow velocity is lower than that on the tank bottom and the intake of dissolved oxygen is weak. In both tanks during the aerobic operation, the flow velocity as a whole is higher than that during the anaerobic operation. It is attributable to the airlift effect. The flow pattern during the aerobic operation is characterized by the flow which is generated, by airlift effect, under the tank top toward the wall. Then, that flow effectively works for the flowing on the tank bottom. Hardly dispersed, the pollutant concentration indicates that the flowing is sufficient in the tank. 4 refs., 6 figs., 3 tabs.

  17. Mixing of two-component flow in a simplified stirred tank with cellular automaton method; Cellular automaton ho ni yoru kakuhan sonai no niseibunryu no kongo keisan

    Watanabe, S; Takahashi, R [Tokyo Institute of Technology, Tokyo (Japan)


    The applicability of a cellular automaton technique to engineering problems will be examined by dealing with mixing in multicomponent flow. The quality and accumulation rate of the product depend on the mixing of raw materials basically. After thoroughly understanding the mixing process, we optimize the geometrical allocation of such elements as a propeller with casing, a chimney and a product output nozzle in a reactor. Usually mixing is formulated by partial differential equations of conservation laws and empirical formulae, and solved numerically by the finite difference technique. In order to evaluate the fine structure of time-dependent interfacial behavior in multicomponent flow, the cellular automaton technique is used, since this has an advantage of describing the pattern formation in detail. It will be demonstrated in the present paper that mixing of two-component immiscible flow is reasonably simulated mesoscopically. 13 refs., 17 figs.

  18. Efflux Performance of Submicron Particles in Packed Bed under Periodic Pressure Conditions; Shuki atsuho ni yoru juten sonai sabumikuron biryushi no ryushutsu tokusei

    Ping, Z; Iritani, E; Murase, T [Nagaya Univ. Nagoya (Japan). Department of Chemical Engineering


    Permeation experiments of ultrapure water were conducted under periodic pressure conditions using a packed bed obtained by dispersing submicron particles of polymethyl methacrylate (PMMA) uniformly into a packed bed of particles of White Alundum. It is clearly demonstrated that washing performance under periodic pressure conditions where the permeation pressure is applied periodically is improved dramatically, compared with that under constant pressure conditions. It is also shown that the effect of periodic pressure operation is especially noticeable in the initial stage of the pressurizing period, and that a pressurizing time smaller than 2 min is very effective under conditions examined in this study. 4 figs.

  19. Development of optical interference-type micro accelerometer for subsurface microseismic measurement; Micromachining ni yoru chika danseiha keisoku no tame no hikari kanshogata kasokudo sensor no kaihatsu

    Hirata, K; Niitsuma, H; Esashi, M [Tohoku University, Sendai (Japan). Faculty of Engineering


    Manufacture is under way of an optical interference-type micro accelerometer making use of the micromachining technology and an optical fiber measuring system for detecting microseismic waves in the ground. The sensor is required to be capable of detecting acceleration 0.1-1gal in amplitude, to be flat in amplitude characteristic in a frequency range of 10Hz-several kHz, to be ensured of straight phase characteristics to enable the measurement of transient phenomena, to be low in cross sensitivity, and to be high in resistance to water, pressure, and heat. The sensor is constructed in the following way. In the process for treating silicon, anisotropic etching is performed for the formation of a gap between the fiber end face and oscillator, boron is diffused, a stopper is formed, and then the silicon is subjected to penetrating etching. In the process for the optical fiber section, an optical fiber is inserted into a glass tube and fixed by an adhesive agent, and then the glass tube end face is polished, this together with the fiber end. Indium-tin oxide is sputtered onto the glass tube end. Finally, the sensor is assembled. 5 refs., 4 figs., 1 tab.

  20. Development of micro capacitive accelerometer for subsurface microseismic measurement. Second Report; Micromachining ni yoru chika danseiha kenshutsu no tame no silicone yoryogata kasokudo sensor no seisaku. 2

    Nishizawa, M; Lim, G; Niitsuma, H; Esashi, M [Tohoku University, Sendai (Japan)


    Micromachining-aided manufacture is under way of a silicon capacitive accelerator sensor, high in sensitivity and broad in bandwidth, for detecting subsurface microseismic waves. The sensor detects acceleration by use of changes in capacities of the top and bottom capacitors generated when a spring-supported weight experiences displacement upon application of acceleration to the said weight. A diode bridge circuit is employed as the circuit for detecting acceleration. As for sensitivity of the sensor, when the virtual noise inputted into the electronic circuit is presumed at 1{mu}V and the circuit driving voltage at 5V, the sensor minimum detectability will be 2.5mgal in the presence of a 3{mu}m gap between the weight and an electrode plate. The natural vibration frequency is set at 1kHz. Such specifications may be realized using the current micromachining technology, and possibilities are that the bandwidth will be further expanded when the sensor is used in a servo-type configuration. The effort is still at the stage of acceleration sensor manufacturing, with a stopper just formed for the silicon weight. 9 refs., 6 figs., 1 tab.

  1. Fundamental principles of a new EM tool for in-situ resistivity measurement. 2; Denji yudoho ni yoru gen`ichi hiteiko sokutei sochi no kento. 2

    Noguchi, K; Aoki, H [Waseda University, Tokyo (Japan). School of Science and Engineering; Saito, A [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)


    In-situ resistivity measuring devices are tested for performance in relation to the principle of focusing. After numerical calculation, it is shown that in the absence of focusing the primary magnetic field will prevail and that changes in the separate-mode component will be difficult to detect in actual measurement because the in-phase component assumes a value far larger than the out-of-phase component. Concerning the transmission loop radius, the study reveals that a larger radius will yield a stronger response and that such will remove the influence of near-surface layers. Two types of devices are constructed, one applying the principle of focusing and the other not, and both are activated to measure the response from a saline solution medium. The results are compared and it is found that focusing eliminates the influence of the primary magnetic field and that it enables the measurement of changes in resistivity of the medium which cannot be detected in the absence of focusing. 3 refs., 9 figs.

  2. Fault fracture zone evaluation using borehole geophysical logs; case study at Nojima fault, Awaji island; Kosei butsuri kenso ni yoru danso hasaitai no hyoka

    Ikeda, R; Omura, K [National Research Institute for Disaster Prevention, Tsukuba (Japan); Yamamoto, T [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)


    Ikeda, et al., in their examination of log data obtained from a borehole (2000m deep) drilled at Ashio, Tochigi Prefecture, where micro-earthquakes swarm at very shallow levels, pay special attention to porosity. Using correlationship between the porosity and elastic wave velocity/resistivity, the authors endeavor to find the presence of secondary pores, dimensions of faults, composition of water in strata in faults, and difference in matrix between rocks, all these for the classification and evaluation of fault fracture zones. In the present report, log data from a borehole (1800m deep) drilled to penetrate the Nojima fault (Nojima-Hirabayashi, Awaji island) that emerged during the Great Hanshin-Himeji Earthquake are analyzed in the same way as the above-named Ashio data, and the results are compared with the Ashio results. Immediately below the Nojima-Hirabayashi fault fractured zone, stress is found remarkably reduced and the difference stress quite small in size. This is interpreted as indicating a state in which clay has already developed well in the fault fractured zone ready to allow the occurrence of shear fracture or a state in which such has already occurred for the release of stress. 4 refs., 5 figs.

  3. Simulation of fault-bend fold by incompressible Newtonian fluid; Hiasshukusei Newton ryutai ni yoru danso oremagari shukyoku kozo no simulation

    Tamagawa, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Tsukui, R [Japan National Oil Corp., Tokyo (Japan). Technology Research Center


    Incompressible Newtonian fluid simulation is experimentally applied to faults typical of the compression and extension fields. A fault-bend folding structure of the flat-ramp flat fault in the compression field and a folding structure of a normal fault in the extension field are studied, and the results are compared with those obtained by the balanced cross section method. The result of calculation indicates that the velocity gradient with the ramp angle set at 30deg is correspondent to stress and that stress concentration is taking place at the ramp section of the fault. This solution is an approximation and does not necessary support the conservation of area but, when the ramp angle is allowed to change from 10 through 40deg, it is found that the conservation of area holds though roughly. It is found that the configuration of the folding structure formed by a flat-ramp flat fault is positioned between the anomalous-mode layer parallel shear typical of a balanced cross section and the folding structure formed by a vertical shear. 7 refs., 7 figs.

  4. Applying flame colors to mixture strength measurement in laminar premixed flames. 2nd Report; Kaenshoku ni yoru soryu yokongo kaen no toryohi keisoku. 2

    Tatsuta, S. [Asahikawa National College of Technology, Hokkaido (Japan); Fujita, O.; Ito, K. [Hokkaido University, Sapporo (Japan). Faculty of Engineering


    The flame color method to measure mixture strength in laminar premixed flames was investigated as a new combustion diagnostic technique. Flame colors were quantitatively determined by chromaticity coordinates (x, y) defined by the CIE 1931 standard colorimetric system. Using 12 types of hydrocarbons, the (x, y) of an inner cone in premixed laminar flames held on a circular tube burner were measured with a colorimeter, and the relationship between the (x, y) and the equivalence ratio {phi} of the mixture was examined in a range of {phi}=0.9 to 1.4. The experimental results indicated that the equivalence ratio could be measured with accuracy of 0.008-0.014 and error due to axial position in the inner cone was less than 0.02-0.05. Humidity of air had almost negligible effects on the accuracy of the measurement. Results also indicated that the effect of back-light could be corrected by introducing the concept of additive mixture of color stimuli. 21 refs., 8 figs., 2 tabs.

  5. Rapid production of metallurgical coke by a pressurized hot-briquetting method. Netsukan kaatsu seikei ni yoru cokes no jinsoku seizo no kokoromi

    Miura, K.; Hayashi, J.; Noguchi, N. (Kyoto University, Kyoto (Japan). Research Laboratory of Carbonaceous Resources Conversion Technology); Hashimoto, K. (Kyoto University, Kyoto (Japan). Faculty of Engineering)


    Rapid production of metallurgical coke from non- and slightly coking coals was studied by pressurized hot-briquetting method. Coal specimens were filled into the mold after pulverizing, and heated at a constant temperature rise rate up to caking temperature under loading pressure to obtain caked coal specimens. Such specimens were then carbonized in nitrogen gas at 800[degree]C. As a result, the coke obtained was superior in compressive strength as compared with commercial cokes, however, its CO2 reactivity was very high requiring heating up to 1,000[degree]C to decrease it, while the reactivity was strongly dependent on coal kind. The optimum processing conditions for slightly coking coal were as follows; loading pressure: 10 [times] 10[sup 5] Pa or more, temperature range under loading pressure: 300-450[degree]C, temperature rise rate: 2-100[degree]C/min, and caking temperature: nearly 500[degree]C. No coke could be produced from coking coals because no volatile matter could be removed from it in a short time under pressure. 13 refs., 8 figs., 1 tab.

  6. Low-frequency noise reduction of fans using the acoustically treated duct; Kyuon duct ni yoru fan soon no teishuhaiki teigen

    Kaneko, K; Fujii, S [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering; Shirasaya, H [Kawasaki Heavy Industries, Ltd., Tokyo (Japan)


    Reducing noise in a low frequency region of 1 kHz or less has become an important problem as a result of emergence of an ultra-high bypass engine in aircraft engines. Therefore, an attempt was made of experimenting and analyzing noise absorption characteristics in low-frequency noises. In the experiment, a low-frequency flow with an air volume of about 3 m{sup 3}/minute was made at a stable operating point of a fan device consisting of moving blades and static blades, with a sound absorbing duct disposed in the forward section. The duct is a 500-mm long steel box with an oblong cross section, in which the top and the bottom parts can move vertically, and a variable air layer was formed between a sound absorbing material (a sheet material made of microfine spherical resin powders solidified to a thickness of 6 mm) and a rigid wall made of iron plate. Noise waves and sound absorption amount were measured on different air layer thicknesses, and analyzed theoretically. As a result, such findings were obtained as: the sound absorption amount is affected by the main stream direction mode of sound pressures in cavity; valleys are formed where the sound absorption amount decreases remarkably in a specific cycle; and peaks are built where the sound absorption amount increases in other regions. 7 refs., 12 figs.

  7. Wind tunnel investigation of a USB-STOL transport semi-span model. 2; CAD sekkei ni yoru USB-STOL ki hansai mokei no fudo shiken. 2

    Takahashi, H; Okuyama, M; Fujieda, H; Fujita, T; Iwasaki, A [National Aerospace Laboratory, Tokyo (Japan)


    The Quiet Short Take-Off and Landing (QSTOL) Experimental Aircraft `ASKA` has been researched and developed by the National Aerospace Laboratory (NAL). The `ASKA` was based upon the airframe of the home produced C-1 tactical transport which was modified into the Upper Surface Blowing (USB) -powered high- lift STOL aircraft. The wing configuration, however, was not changed. Therefore, this Experimental Aircraft does not always have the optimum configuration of a USB-type aircraft. So the authors tried to improve the aerodynamic characteristics of the STOL Aircraft. This paper describes the investigations which have been conducted to improve the aerodynamic characteristics of a subsonic jet transport semi-span model with an Upper Surface Blown Flap system which has been newly designed using the NAL STOL-CAD program. The model had an 8.2{degree} swept wing of aspect ratio 10.0 and four turbofan engines with short USB nozzles. The tests were conducted in the NAL 2{times}2m Gust Wind Tunnel with closed section and results were obtained for several flap and slat deflections at jet momentum coefficients from 0 to 1.85. Compared with the aerodynamic characteristics of the `ASKA` model, we determined that the airframe weight can be reduced and the aerodynamic characteristics can be improved significantly. 14 refs., 44 figs.

  8. Entrapment and degradation of particulate organics in anaerobic fluidized bed reactor. Kenkisei ryudosho ni yoru fuyusei yuki kokeibutsu no hosoku to bunkai

    Araki, N. (Nagaoka National College of Technology, Niigata (Japan)); Harada, H.; Momonoi, K. (Nagaoka University of Technology, Niigata (Japan))


    A start-up experiment on an anaerobic fluidized bed reactor has been performed using simulated wastewater added with cellulose as a suspended substance to discuss behavior of suspended base materials and change in bacterial phases of biofilm constituting bacteria cluster. Cellulose removal efficiency of the reactor was 98% of a volumetric load of up to 2 g COD[center dot]1[sup -1][center dot]d[sup -1] performing efficient decomposition including methane. Cellulose content in the fluidized bed increased to 3% to 16% of the fluidized bed MLVSS with increase in a volumetric load from 3 to 10 g COD[center dot]1[sup -1][center dot]d[sup -1]. Bacteria, of which activity changes largely with growth of biofilms among other anaerobic bacteria clusters, are acid producing bacteria and acetic acid-selective methane bacteria, which have grown to 31 times and 70 times at maximum respectively as compared to their species sludge. Sludge resident time in the reactor has dropped rapidly from 80 days to 2.6 days as a result of accumulation of cellulose in the biofilms. The cellulose decomposing activity of the biofilms increases as the biofilms grow. The maximum value was 0.20 Cellulose[center dot]g[sup -1] VSS[center dot]d[sup -1]. 19 refs., 8 figs., 4 tabs.

  9. Fluidized pellet bed bioreactor system for SS, COD, nitrogen and phosphorus; Ryudoso zoryu bio reactor system ni yoru SS, COD, chisso oyobi rin jokyo

    Shimizu, T.; Tanbo, N.; Kudo, K. [Hokkaido University, Sapporo (Japan). Faculty of Engineering; Hamaguchi, T.; Nakabayashi, A. [Tsukishima Kikai Co. Ltd., Tokyo (Japan)


    An examination was carried out on a treatment system which was constituted of an aerobic fluidized pellet bed (AFRB) bioreactor and the two steps comprising a contact aeration process and a sand filtration process for sewage/drainage treatment. The following data were obtained from the experiment by a pilot plant installed in a sewage plant. The removal ratios were the same as or above 95% in SS, 95% in total phosphorus, 85% in COD and 80% in total nitrogen. The highly dense sludge pellets formed in the AFPB bioreactor in summer contained aerobic filamentous bacteria that were capable of multiplying. The sludge retention time of this bioreactor was 2.2 to 8.1 days which were sufficient for the multiplication of denitrifiers, whose number and activity were also satisfactory for dinitrification. Further, other microorganisms existed in the bioreactor such as sulfate reducers and methanation bacteria. The role of a contact aeration tank was the oxidized decomposition and nitration of soluble BOD, and the biofilm had niterite and nitrate bacteria adhered to it. Assuming the retention time of the tank was two hours, the nitration ratio was 90% or more at the water temperature of 15{degree}C or higher. 29 refs., 12 figs., 2 tabs.

  10. Characterization of algae removal in a fluidized bed biofilm reactor system for lake water treatment; Kokisei ryudosho seibutsu rokaho ni yoru kosuichu no sorui jokyo tokusei

    Tanaka, T.; Tsuzuki, K.; Nishijima, N.; Takagi, T. [Hitachi, Ltd., Tokyo (Japan); Terazono, K. [Water Resources Environment Technology Center, Tokyo (Japan)


    This paper describes a pilot plant study on algae removal of a fluidized bed biofilm reactor system for lake water treatment. The system does not need backwashing because the fluidized bed suffers no clogging. Moreover, the system uses dissolved oxygen in influent water for aerobic biological treatment without aeration equipment. Thus, this system is a low energy and easy maintenance way to purify eutrophic lake water. The system was operated continuously at a flow rate of 1500 m{sup 3}/d{sup 1} for 9 months at Tsuchiura Port in Lake Kasumigaura. In this study, chlorophyll-a and dissolved oxygen in both influent and effluent water were monitored continuously. In summer (August to September) when water bloom occurred, the average removal efficiency of chlorophyll-a was 64% at the average influent chlorophyll-a concentration of 137.8 {mu}g/l{sup 1}. During the total experimental period (9 months), the average daily amount of removed chlorophyll-a was 40.3 g/d{sup 1} at the average influent chlorophyll-a concentration of 89.5 {mu}g/l{sup 1}. By analyzing the relationship between the removed chlorophyll-a and the consumption of dissolved oxygen, it was estimated that almost all of algae trapped in the reactor was degraded biologically. 20 refs., 12 figs., 2 tabs.

  11. Hydrophobization og the surface fo malachite with some fluorosurfactants. 2,3 no fussokei kaimen kasseizai ni yoru malachite hyomen no sosuika

    Kobayashi, M [National Reserach Institute for Pollution and Resources, Tsukuba (Japan); Wakamatsu, T [Kyoto University, Kyoko (Japan). Faculty of Engineering


    The depleting trends of high-grade ores in recent years make it unavoidable to float ores in fine powder forms. To achieve this, research and development is important on such a recovering agent that can hydrophobize the surfaces of useful ores selectively and powerfully. This paper describes the discussion on three kinds of fluorosurfactant, namely perfluorooctanoic acid, Ftergent-100 and Ftergent-150, whic were used to hydrophobize the surface of malachite, and compared of its utilization possibility as a recovery agent with other surfactants. As a result, it was found that the Ftergent-100, which contains five CF{sub 3}{sup {minus}} in one molecule having extremely low critical surface tension, and the Ftergent-150 can hydrophobize sufficiently the malachite surface and provide good deposition. The region providing good deposition was at a weak-acidic to weak-alkali region in the case of the Ftergent-150. Therefore, both materials are thought they could be used as a recovering agent. 8 refs., 10 figs., 3 tabs.

  12. Selective extraction of palladium with caffeine from acidic chloride media; Sansei enkabutsu yoeki karano kafuein ni yoru parajiumu no sentakuteki chushutsu

    Kaikake, K.; Baba, Y. [Miyazaki University, Miyazaki (Japan). Faculty of Engineering


    In order to examine the possibility of caffeine as an extractant, the extraction of metal ions from acidic chloride media was studied at 298 K using the mixture solvent of chloroform and 2-ethyl-1-hexanol. Caffeine has exhibited a high selectivity for palladium (2) over base metals such as copper (2), nickel (2), and iron (3), and over precious metal such as platinum (4). The stoichiometric relation in the extraction of palladium (2) with caffeine was elucidated by examining the effects of chloride ion, hydrogen ion, and caffeine concentrations on its extractability. In addition, palladium (2) was found to be extracted selectively with caffeine from the mixture containing a 25-fold amount of platinum (4) or copper (2). The stripping of palladium (2) was performed to an extent of 80% by a single batchwise treatment with an aqueous mixture solution of hydrochloric acid and thiourea. (author)

  13. Study on the inside gas flow visualization of oxygen sensor cover; Kashika ni yoru O2 sensor cover nai no gas nagare hyoka

    Hocho, S; Mitsuishi, Y; Inagaki, M [Nippon Soken, Inc., Tokyo (Japan); Hamaguchi, S; Mizusawa, K [Toyota Motor Corp., Aichi (Japan)


    In order to make clear the difference of the response time between the oxygen sensors with different protection covers, we visualized gas flow inside of sensor covers by means of two experimental methods: One is `Smoke Suspension Method` using liquid paraffin vapor as the smoke. With smoke suspension method, we detected the streamlines inside of the covers. The other is `Color Reaction Method` using the reaction of phenolphthalein and NH3 gas. With color reaction method, we confirmed the streamline inside of the cover and furthermore detected the difference of the response time of each sensor. 3 refs., 7 figs., 1 tab.

  14. Estimation of tire characteristics by concerning test data of vehicles; Jidosha no senkai shiken data ni yoru dire tokusei no suisan

    Nakamura, M; Sekine, T; Nagae, H [Nihon University, Tokyo (Japan)


    To study and/or develop the vehicle motion of a braking in turns theoretically, the cornering characteristics of the tire under the action of braking forces must be required. On the other hand, such data are very few to be published and also there be few tire testing machine to be able to use. The authors tried to derive such data from the vehicle behaviors in steady turns and braking in turns. Because each wheel loads are unknown factors, the two wheeled vehicle model are employed in analysis. The methodology of analysis and the reasonable results are presented in this paper. 5 refs., 10 figs., 2 tabs.

  15. Analysis of stress distribution of timing belts by FEM; Yugen yosoho ni yoru timing belt oryoku kaiseki (belt code oryoku bunpu kaiseki hokoku)

    Furukawa, Y; Tomono, K; Takahashi, H; Uchida, T [Honda R and D Co. Ltd., Tokyo (Japan)


    A model of the belt analyzed by-ABAQUS (: a general nonlinear finite element program) successfully confirmed the mechanism that generates the belt cord stress. A quite good agreement between experimental and computed results for the stress distribution of the belt cord. It is found that maximum stress of the cords occurs near the root of the tooth by calculation, where the belt cords break off. 3 refs., 9 figs.

  16. Experimental analysis of the structure attenuation characteristics on engine noise by pseudo cylinder pressure excitation; Giji tonaiatsu kashin ni yoru engine kozo no soon tokusei hyoka

    Ozawa, H; Nakada, T [Isuzu Advanced Engineering Center, Tokyo (Japan)


    The engine structure attenuation has been experimentally analyzed by the newly developed in-cylinder excitation system. It can reproduce the complete cylinder pressure in non-running engine conditions by adopting the hydraulic and the piezoelectric actuator. The structure attenuation measured in this system has a good coincidence with the ones measured in actually engine operating conditions, meanwhile the current method, which applied only high frequency components as the excitation pressure, was shown to have the unsatisfied agreement. As a result, the proposed system has been concluded to be very useful to estimate the engine noise characteristics in non-running conditions. 4 refs., 11 figs., 1 tab.

  17. Improvement of road noise by reduction of acoustic radiation from body panels; Panel no hoshaon teigen ni yoru road noise no kaizen

    Kamura, T; Utsunomiya, A; Sugihara, T; Tobita, K [Mazda Motor Corp., Hiroshima (Japan)


    This paper describes road noise reduction methods accomplished by reducing acoustic power radiated from body panels. Fundamental study of acoustic and dynamic characteristics with rectangular panels revealed following results: (1) The lower stiffness panel had lower radiation efficiency and made damping materials work more effective to reduce the acoustic power. (2) The acoustic power was also reduced by designing the panel so that it can generate the vibration of (2, 2) mode, which has the lowest radiation efficiency, in road noise frequency region. By applying these methods to a vehicle floor, we confirmed the improvement of road noise performance. 3 refs., 12 figs.

  18. Development of aluminium viscous damper by high speed MIG welding process; Kosoku MIG yosetsuho ni yoru aluminium sei viscous damper no kaihatsu

    Hino, H; Hotta, M [Nippon Light Metal Co. Ltd., Tokyo (Japan); Maeda, Y; Shimizu, H [Fukoku Co. Ltd., Saitama (Japan)


    We have developed a welded aluminum viscous damper to improve the joining strength between the case and the cover of the conventional damper mechanically fastened by adhesion. The distortion of the welded damper was decreased to an acceptable level using the high speed MIG welding process. Sound quality and good appearance were obtained by optimizing the initial speed of the filler wire and by controlling the welding conditions at the starting part and in the lap part. The leakage load and the fatigue limit of the welded damper were 5 and 10 times those of the conventional damper, respectively. 3 refs., 15 figs.

  19. Degradation of organophosphoric acid triesters by the aquatic bacteria and toxicity to fish; Yuki rinsan toriester no suichu saikin ni yoru bunkai to dokusei

    Kawai, S. [Kobe College, Hyogo (Japan)


    This paper describes biodegradation of organophosphoric acid triesters (OPEs) in water environment, in particular, by aquatic bacteria. In culture experiment using river water in Osaka, aryl system OPEs such as triphenyl phosphate (TPP) and tricresyl phosphate (TCP) are more easily degraded than alkyl system OPEs, and OPEs including Cl are hardly degraded. Properties of isolated TBP degradation bacteria and enzymes, and TCP degradation bacteria isolated from Mukogawa river water are examined. OPEs are toxic to fishes equivalently to or more than organophosphoric system pesticides. However, the cause of their toxicity can`t be interpreted only by cholinesterase activity hindrance of nervous system. Absorption, accumulation, metabolism and degradation of OPEs are dependent on fishes and kinds of OPEs. Although the toxicity evaluation using experimental animals is important, the evaluation using cultured bacteria is recognizing once again from various viewpoints. Direct toxicity of OPEs to fishes or aquatic organisms is yet unidentified, however, the influence of OPEs on human beings is rather important. 39 refs., 10 figs., 2 tabs.

  20. Soot and NOx simultaneous reduction by use of CO2 mixed fuel; Ekika CO2 yokai nenryo ni yoru diesel kikan no susu, NOx no doji teigen

    Senda, J; Yokoyama, T; Ikeda, M; Fujimoto, H [Doshisha University, Kyoto (Japan); Ifuku, Y [Kubota Corp., Osaka (Japan)


    We propose the new fuel injection system by use of diesel fuel dissolved with CO2 to reduce both soot and NOx simultaneously. In this paper spray combustion characteristics of CO2 mixed fuel is reported. It is revealed that flame temperature and KL factor at the CO2 mixed fuel combustion are lower than at the only n-tridecane combustion due to separation or partly flashing of CO2component. And the result of exhaust gas measurement shows the capability that CO2 mixed fuel is able to reduce both soot and NOx simultaneously. 12 refs., 7 figs., 1 tab.

  1. Automobile simulation model and its identification. Behavior measuring by image processing; Jidosha simulation model to dotei jikken. Gazo kaiseki ni yoru undo no keisoku

    Suzuki, H; Morita, S; Matsuura, Y [Osaka Sangyo University, Osaka (Japan)


    Model simulation technology is important for automobiles development. Especially, for the investigations concerning to ABS, TRC, VDC, and so on, the model should be the one which can simulates not only whole behaviors of the automobile, but also such internal information as torque, acceleration, and, velocity of each drive shafts, etc.. From this point of view, 4-wheels simulation model which can simulates almost over 50 items, was made. On the other hand, technique of 3-D image processing using 2 video cameras was adopted to identify the model. Considerably good coincidences were recognized between the simulated values and measured ones. 3 refs., 7 figs., 2 tabs.

  2. Identification of Fusarium oxysporum in the fluid of hydroponic culture using DNA analysis; DNA kaiseki ni yoru suiko saibai yoekichu no horenso ichobyokin

    Oyama, K.; Kawabata, T. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)


    In the case of circularly using a fluid of the hydroponic culture for crops such as vegetable, the destructive damage is caused when specified harmful germs multiply in the growing crop. therefore, it is necessary to find the germs in question out and deal with them as quickly as possible. In this paper, studies were made on a sure identification technology of F. oxysporum using DNA analysis and the measures to prevent crop damages caused by diseases. The results of the study are reported. (translated by NEDO)

  3. Investigation of the simulation for the solar DHW system by TRNSYS; TRNSYS ni yoru kaihogata tank wo mochiita solar kyuto system no simulation chosa

    Oishi, M; Noguchi, T [Japan Quality Assurance Organization, Tokyo (Japan); Okumiya, M [Nagoya University, Nagoya (Japan)


    With an objective of establishing a method for evaluating performance of a photovoltaic hot water supply system, a discussion was given on utilization of the simulation program, TRANSYS. The discussion was addressed on a photovoltaic hot water supply system of forcible circulation type using commercially available open-type heat storage tanks. An experiment was performed as an indoor test using an artificial solar light source. The TRANSYS makes available a type 04 which handles each node as a complete mixture by fixing and dividing the heat storage tank, and a type 38 which expresses heat transfer between temperature layers by means of piston flow as a heat transfer coefficient. Both types were subjected to calculation. The result of the discussion may be summarized as follows: both types provided values close to the experimental values of quantity of heat derived by utilizing solar heat; however, with the type 04, heat transfer cannot be modeled if the system is left still with temperature difference in the heat storage tank being large; and with the type 38, modeling is possible when the system is left still with temperature difference in the heat storage tank being large, but temperature gradient is difficult to be modeled during heat collection and when hot water is supplied. 1 ref., 7 figs., 5 tabs.

  4. Character of photovoltaic/thermal hybrid collector. Character analysis by numerical calculation; Taiyoko netsu hybrid collector no tokusei. Suchi keisan ni yoru tokusei kaiseki

    Morita, Y; Iwawaki, T; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)


    In order to investigate characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/T{sub s}) operating under varying conditions, energy equilibrium equations have been developed for numerical calculation, and the calculated results were compared with the observed ones. The calculated characteristics are close to the observed ones, both for photoelectric conversion and heat collecting characteristics, demonstrating validity of these energy equations. It is found, by comparing characteristics of PV/T{sub A} (covered with glass) with those of PV/T{sub B} (not covered with glass), that these characteristics are greatly affected by glass cover. Maximum overall excergy levels attained are 13.29% with PV/T{sub A} and 11.48% with PV/T{sub B} under the conditions of solar radiation intensity H: 800W/m{sup 2}, ambient temperature: 20degC and wind velocity: 0.5m/s, where flow rates of heat medium are 2.0times10{sup -3} and 4.0times10{sup -3}kg/s, respectively. Thus, the PV/T{sub A} system has a higher maximum excergy efficiency than the PV/T{sub B} system. The PV/T{sub A} gives water of higher temperature, demonstrating that covering the system with glass increases maximum excergy efficiency and optimum temperature. 6 refs., 5 figs., 2 tabs.

  5. Optimal operation by dynamic programming in a solar/electric hot-water system; Taiyonetsu/denryoku kyuto system no doteki keikakuho ni yoru saiteki un`yo

    Edo, S; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)


    With regard to utilization of a solar/electric hot-water system, a discussion was given by using a dynamic programming method on operation of a system which minimizes power charge. The discussed system is an installation in a welfare facility accommodating 100 persons, where solar heat is stored in a heat storage tank from a heat collector, and utilized for hot water supply. If the solar heat is insufficient for required hot water quantity, the water is heated by using an electric heater. The discussion compared the system operation using the dynamic programming method with the following two systems: the operation method 1, which does not utilize insolation forecast and the operation method 2, in which insolation forecast is utilized and late-night electric power is utilized for heating water in shortage. As a result of the calculation, the operation using the dynamic programming method conducts heat storage by utilizing the late-night power even if insolation is sufficient in winter in order to suppress heating by utilizing late-night power for days with less insolation. Thus, suppression is given on excessive utilization of day-time power and on rise in annual maximum power demand. It was found that the present system reduces power consumption by 37.7% when compared with the operation method 1, and 22.7% when compared even with the operation method 2. 3 refs., 5 figs., 3 tabs.

  6. Estimation of clearness index using neural network with meteorological forecast; Kisho yoho wo nyuryoku toshita neural network ni yoru seiten shisu no yosoku

    Nishimura, S; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)


    Discussions were given on estimation of clearness index in order to operate stably a solar energy utilizing system. All-sky insolation amount varies not only by change in the climate, but also seasonal change in the sun`s altitude. Therefore, a clearness index (ratio of all-sky insolation to out-of-atmosphere insolation) was used. The larger the value, the higher the solar ray permeability. The all-sky insolation amount is a measured value, while the out-of-atmosphere insolation amount is a calculated value. Although the clearness index may be roughly estimated by weather forecast, the clearness index varies largely even on the same weather forecast, especially for cloudy days, if a weather forecast actually having error is used. Therefore, discussions were given on estimation of the clearness index by using a neural network which uses meteorological information such as air temperatures and precipitation probabilities as inputs. Using multiple number of meteorological forecast information simultaneously has reduced the average square error to 49% of that using only the weather forecast. The estimation accuracy depends on the accuracy of meteorological forecast, but using multiple number of forecast information can improve the accuracy. 6 refs., 7 figs., 1 tab.

  7. Simulation study on single family house with solar floor and domestic hot water heating system by EESLISM; EESLISM ni yoru taiyonetsu danbo kyuto jutaku no simulation

    Roh, H; Udagawa, M [Kogakuin University, Tokyo (Japan)


    Indoor thermal conditions and energy performance were simulated, by the aid of EESLISM as a common simulation program for indoor thermal conditions and energy systems, for an actual two-storied single family house equipped with solar-heated floors and a domestic hot water (DHW) heating system, in order to investigate applicability of the simulation program. The house, built in Shibuya Ward in Tokyo, has a total floor area of 164m{sup 2}, with a living room, dining room and study heated by the solar system for a total floor area of 35m{sup 2}. A heat-storage tank is provided, dedicated to the DHW system. The solar collector is of flat type, with selectively light-absorbing planes, having a total collector area of 11.46m{sup 2}. The operating conditions of the floor-heating and DHW systems are almost reproduced. It is necessary to take surrounding conditions into consideration; solar radiation in daytime will be overestimated if adjacent buildings are neglected to give higher temperature in the space and on the wall on the south than the observed level. 6 refs., 5 figs., 1 tab.

  8. Assessment of global environmental impacts by utilizing methodology of LCA on solar water heater for dwellings; LCA shuho ni yoru taiyonetsu onsuiki no kankyo fuka hyoka

    Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan); Asai, S [Yazaki Corp., Tokyo (Japan)


    CO2 emission was quantified through the life cycle of a solar water heater to assess its environment impact. Although LCA (life cycle assessment) originally sums up I/O of all materials and energy through the whole life cycle of a product to examine environment impact, this assessment was carried out for only CO2. Calculation of CO2 emission assumed a natural circulating solar water heater of 200 l in effective hot water capacity, 2.78m{sup 2} in effective collecting area, and 0.5 in average annual collecting efficiency of total solar radiation, and an auxiliary city gas heat source for compensating insufficient heat quantity. The total CO2 emission in the life cycle of a solar water heater was obtained from an industrial association table assuming the life cycles of 10 and 20 years. CO2 emission was estimated to be 5407.1kg-CO2 and 10665.2kg-CO2 for 10 and 20 years, respectively. CO2 emission due to city gas was largest in the total CO2 emission in the life cycle. As a result, for reduction of CO2 emission due to a solar water heater, improvement of equipment efficiency was most important. 6 refs., 5 figs., 3 tabs.

  9. Characteristic on photovoltaic/thermal hybrid collector. Evaluation of excergetic theory; Taiyoko netsu hybrid collector no tokusei. Exergy ni yoru hyoka

    Iwawaki, H; Morita, Y; Fujisawa, T; Tani, T [Science University of Tokyo, Tokyo (Japan)


    Described herein are characteristics of photovoltaic (PV)/thermal hybrid collectors (PV/Ts), in which a PV module is combined with a plate-shape solar heat collector to simultaneously produce electric power and heat. Their efficiency is assessed by exergy. The test results indicate that the PV/T system gives a 1.07 times higher exergy than the PV system, 86.3 versus 80.7kWh. In terms of energy, the optimum values (OVs) are 5, 44 and 37% lower than the measuring values (MVs) for electrical energy, thermal energy and total exergy. In terms of exergy, on the other hand, OV is 5% lower than MV for electrical energy, but 893 times higher for thermal energy and 1.26 times higher for total exergy. As a result, the exergy level is 26% higher than that of a system which generates power as the main product and heat as the auxiliary product. 3 refs., 6 figs., 5 tabs.

  10. Inversion of Love wave phase velocity using smoothness-constrained least-squares technique; Heikatsuka seiyakutsuki saisho jijoho ni yoru love ha iso sokudo no inversion

    Kawamura, S [Nippon Geophysical Prospecting Co. Ltd., Tokyo (Japan)


    Smoothness-constrained least-squares technique with ABIC minimization was applied to the inversion of phase velocity of surface waves during geophysical exploration, to confirm its usefulness. Since this study aimed mainly at the applicability of the technique, Love wave was used which is easier to treat theoretically than Rayleigh wave. Stable successive approximation solutions could be obtained by the repeated improvement of velocity model of S-wave, and an objective model with high reliability could be determined. While, for the inversion with simple minimization of the residuals squares sum, stable solutions could be obtained by the repeated improvement, but the judgment of convergence was very hard due to the smoothness-constraint, which might make the obtained model in a state of over-fitting. In this study, Love wave was used to examine the applicability of the smoothness-constrained least-squares technique with ABIC minimization. Applicability of this to Rayleigh wave will be investigated. 8 refs.

  11. Laboratory investigation on streaming potential for sandy soil and weathered rock; Shitsunai jikken ni yoru sashitsu jiban oyobi fuka ganban no ryudo den`i no kento

    Sato, H; Shima, H [OYO Corp., Tokyo (Japan)


    Laboratory experiment on sandy soil and weathered rock was conducted to clarify the generation mechanism of streaming potential due to underground fluid. Streaming potential is caused by underground fluid flow, namely by fluid flow in porous substances as electrokinetic phenomenon. In experiment, Inagi sand, Toyoura sand and strongly decomposed weathered granite were used. In Inagi and Toyoura sands, positive streaming potential was observed downstream in fluid flow. Streaming potential could be nearly determined as primary function of fluid velocity, and generated streaming potential increased with fluid resistivity. Streaming potential was higher in Inagi sand than Toyoura sand, probably depending on hydraulic radius, size of bleeding channel, and conductivity of sand surface. In weathered granite, negative streaming potential was measured. In the case of positive {zeta} potential, negative streaming potential is theoretically generated downstream in fluid flow. This experiment suggested possible generation of negative streaming potential in some kinds of ground. 2 refs., 6 figs., 1 tab.

  12. Resistance test of high-speed ship by means of attitude control method. Part 2; Shisei seigyo hoshiki ni yoru kosokutei no teiko shiken. 2

    Hayashida, S [Nagasaki Institute of Applied Science, Nagasaki (Japan)


    The previous paper has proposed a resistance test method by controlling the attitude of a high-speed model ship using a personal computer without making a data base. For this method, the fluid force acting on the hull of model ship is measured, to change its attitude based on the measurement, and then, the fluid force is measured again, to change the attitude again. The traveling attitude is created by repeating this, to measure the force acting on the hull. Since the attitude is changed by calculating using the fluid force measured, various factors can be considered in the calculation process. For example, a test with an arbitrary displacement in an arbitrary position of center of gravity can be conducted in spite of actual displacement and position of center of gravity of the model ship. A test for a high-speed ship was conducted through this method, to obtain nearly satisfactory results compared with a usual resistance test. Occasionally, a lot of repetitions were required to satisfy the balancing condition of the force. In this study, the improvement of testing efficiency has been planned by modifying the analyzing program. 5 refs., 7 figs., 1 tab.

  13. Computational study on full-wave inversion based on the acoustic wave-equation; Onkyoha hado hoteishiki full wave inversion no model keisan ni yoru kento

    Watanabe, T; Sassa, K [Kyoto University, Kyoto (Japan); Uesaka, S [Kyoto University, Kyoto (Japan). Faculty of Engineering


    The effect of initial models on full-wave inversion (FWI) analysis based on acoustic wave-equation was studied for elastic wave tomography of underground structures. At present, travel time inversion using initial motion travel time is generally used, and inverse analysis is conducted using the concept `ray,` assuming very high wave frequency. Although this method can derive stable solutions relatively unaffected by initial model, it uses only the data of initial motion travel time. FWI calculates theoretical waveform at each receiver using all of observed waveforms as data by wave equation modeling where 2-D underground structure is calculated by difference calculus under the assumption that wave propagation is described by wave equation of P wave. Although it is a weak point that FWI is easily affected by noises in an initial model and data, it is featured by high resolution of solutions. This method offers very excellent convergence as a proper initial model is used, resulting in sufficient performance, however, it is strongly affected by initial model. 2 refs., 7 figs., 1 tab.

  14. Three dimensional numerical modeling for ground penetrating radar using finite difference time domain (FDTD) method; Jikan ryoiki yugen sabunho ni yoru chika radar no sanjigen suchi modeling

    Sanada, Y; Ashida, Y; Sassa, K [Kyoto University, Kyoto (Japan)


    3-D numerical modeling by FDTD method was studied for ground penetrating radar. Radar radiates electromagnetic wave, and determines the existence and distance of objects by reflection wave. Ground penetrating radar uses the above functions for underground surveys, however, its resolution and velocity analysis accuracy are problems. In particular, propagation characteristics of electromagnetic wave in media such as heterogeneous and anisotropic soil and rock are essential. The behavior of electromagnetic wave in the ground could be precisely reproduced by 3-D numerical modeling using FDTD method. FDTD method makes precise analysis in time domain and electric and magnetic fields possible by sequentially calculating the difference equation of Maxwell`s equation. Because of the high calculation efficiency of FDTD method, more precise complicated analysis can be expected by using the latest advanced computers. The numerical model and calculation example are illustrated for surface type electromagnetic pulse ground penetrating radar assuming the survey of steel pipes of 1m deep. 4 refs., 3 figs., 1 tab.

  15. Three dimensional transient electromagnetic model study for fracture prediction from tunnel face; Sanjigen model keisan ni yoru TEM ho no tunnel zenpo tansa eno tekiyosei no kento

    Wada, K; Tsutsui, T; Saito, A [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan); Hara, T [Toda Corp., Tokyo, (Japan); Zhdanov, M [University of Utah, UT (United States)


    In order to apply TEM model to fracture prediction at tunnel face, 3-D TEM model computation by FEM was conducted by installing a transmission loop on a tunnel face. MT field responses diffusing into the 3-D model were computed by time-domain difference calculus, and analytical precision was improved by introducing a staggered grid method. In the case where a low resistive zone exists before a tunnel face, time variance in diffused eddy current and induction current in the low resistive zone could be obtained. The difference in tunnel-axial transient curve (transient phenomenon curve in magnetic field) between uniform medium and low resistive zone models was based on the absorption process of diffused eddy current into the low resistive zone, and the expanding process of it toward the outside. Change in background condition could be predicted from the background and the ratio of transient curves every measurement. The detection limit of the low resistive zone was dependent on resistivity contrast, distance and geometry. Fluctuation in measurement due to noises and S/N ratio were also essential. 3 refs., 10 figs.

  16. Destratification efficiency by hypolimnitic water lifter with air bullets. Kihodan wo mochiita shinsosui yosui shisetsu ni yoru mitsudo seiso no kongo koritsu

    Ikeda, H; Suga, K [Utsunomiya University, Tochigi (Japan). Faculty of Engineering; Asaeda, T [Saitama University, Saitama (Japan). Faculty of Engineering


    The intermittent aeration and circulation method is used frequently to destruct temperature stratification in a reservoir to prevent it from eutrophication. This method uses a cylinder erected in water, into which air bullets are shot out intermittently to circulate and mix heavier water mass upward. The present study has performed numerical analysis on the process to mix density stratifications by operating an intermittent water lifter cylinder for an extended period of time, and discussed responses of each factor to variation. The numerical computation has been carried out according to the equation of motion for water and air in the water lifter cylinder, and the numerical model that hypothesizes the double plume after air bubbles have departed from the water lifter cylinder. The result indicated that the amount of hypolimnitic water lifted against the amount of air injected can be expressed by an empirical formula that uses only the relative air bullet volumes. An evaluation formula for the water lifting efficiency has also been derived. It has been found for the stratification mixing that trends in the mixing efficiency can be identified by two parameters of dimensionless air bubble amount and stratification strength. 17 refs., 11 figs., 4 tabs.

  17. Development of the anomaly diagnosis system for transformers using trace constituents in oil; Yuchu biryo seibun ni yoru hen`atsuki ijo shindan hoho no kaihatsu

    Ono, H.; Ono, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)


    In order to complement an anomaly diagnosis system by analysis of gases in oil for transformers, the analysis/diagnosis method of trace constituents in oil was developed. Liquid-liquid solvent extraction using methanol aqueous solution as extract, and high-speed liquid chromatography were adopted to analyze decomposed products dissolved into oil by over heating as trace constituents. The relation between over heat temperature and the amount of decomposed products by over heating was studied by simulation experiment of over heat anomaly. The detectable duration of anomaly after its generation was also studied by examining the adsorption phenomenon of the thermal decomposed products onto insulating materials. As a result, the criterion of the analysis/diagnosis method was prepared by using 5-hydroxymethylfurfural as index constituent of over heating anomaly. Although furfural was also effective as index constituent, it was excluded from the index constituent because furfural is formed by deterioration of transformers even during normal operation. 2 refs., 19 figs., 7 tabs.

  18. Diagnosis by acetone for deterioration of breathing transformers containing an adsorbent in the insulating oil; Acetone ni yoru kyuchakuzai iri kaihogata hen`atsuki no keinen rekkado shindan

    Awata, M.; Mizuno, K.; Ueda, T. [Chubu Electric Power Co. Ltd., Nagoya (Japan); Ota, N.; Ishii, T.; Tsukioka, H.


    The high-precision diagnosis for deterioration of a breathing transformer containing an adsorbent was investigated. An adsorbent (activated alumina) may be contained in oil to eliminate the deterioration product in insulating oil or the moisture. In this case, the deterioration component furfural in insulating paper is adsorbed. The concentration in furfural oil cannot be thus used for deterioration diagnosis. Acetone and furan with good relation between the adsorption characteristics for activated alumina and the insulating paper deterioration in an accelerated deterioration test can be effectively used as a new deterioration index component of insulating paper. The disassembly survey showed that acetone is valid as the index component of deterioration diagnosis. Furan is not detected in a breathing transformer, but effective in diaphragm-type and nitrogen-sealed transformers. The adsorption of acetone by activated alumina requires no correction for the change in oil temperature at about 10{degree}C. The solubility of acetone for insulating oil is 60 times at 20{degree}C as high as CO2, and the discharge rate from a breather is little (1/25). Therefore, acetone is much more excellent than CO2 as the precision of a deterioration index. 21 refs., 15 figs., 4 tabs.

  19. Cavity detection based on EM migration of TEM data; TEM ho data no denji migration ni yoru kudo kenshutsu no kokoromi

    Shiga, N; Wada, K; Tsutsui, T [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan); Hara, T [Toda Corp., Tokyo (Japan)


    With an objective to discuss applicability of resistivity imaging using electromagnetic migration to detection of underground cavity, an applicability test was carried out on calculation of a numerical model and measurement data. By using the numerical model, a calculation was performed on a hypothetical case that a cubic cavity with sides each at 40 m exists in a homogenous medium of 200 ohm-m, with the cavity top located 20 m below the ground surface. As a result, it was possible to structure in a very short calculation time an image of the cavity which cannot be identified by one-dimensional inverse analysis. In the case of this cavity, a center of the image was structured on its lower face. It was shown that a location to indicate the image must be changed according to difference in the measurement locations. In a test on data measured in an underground cavity in the city of Utsunomiya, Tochigi Prefecture, it was found that the result may vary largely depending on structure of the background necessary for migration. Referring to a result of measurement performed in a location in which no target has been set can provide a good result. 5 refs., 7 figs., 1 tab.

  20. Geoelectrical structure by electrical logs and Schlumberger sounding at the Akinomiya geothermal field, Akita Prefecture; Denki kenso oyobi Schlumberger ho ni yoru Akinomiya chinetsu chiiki no hiteiko kozo

    Kajiwara, T; Takemoto, S


    Based on the electrical logging data of the existed well and Schlumberger sounding data obtained in 1974, a two-dimensional inversion analysis of the specific resistance profile was conducted at the Akinomiya geothermal field, Akita Prefecture. From the electrical logging data, relationships between the geology and the specific resistance were illustrated. The specific resistance values of basement rocks showed more than 100 ohm-m, which were higher than those of the other seams. Intrusive rocks and tuffs in the basement rocks showed locally low values less than 100 ohm-m. Younger volcanic rocks showed low values around 10 ohm-m. As a result of the two-dimensional inversion analysis, the basement rocks could be detected as high specific resistance layers. Accordingly, it was considered that the basement rocks in this field can be detected as high specific resistance layers by analyzing the results of field survey sufficiently. Low specific resistance zones were observed in the shallow depth, which corresponded to the fumarolic gases. There were some layers with remarkably varied specific resistance values, which were considered to be related with alteration. 6 refs., 3 figs.

  1. Development of micro capacitive accelerometer for subsurface microseismic measurement; Micromachining ni yoru chika danseiha kenshutsu no tame no silicon yoryogata kasokudo sensor no seisaku

    Nishizawa, M; Niitsuma, H; Esashi, M [Tohoku University, Sendai (Japan). Faculty of Engineering


    A silicon capacitive accelerometer was fabricated to detect subsurface elastic waves by using micromachining technology. Characteristics required for it call for capability of detecting acceleration with amplitudes from 0.1 to 1 gal and flat amplitude characteristics in frequency bands of 10 Hz to several kHz. For the purpose of measuring transition phenomena, linear phase characteristics in the required bands must be guaranteed, cross sensitivity must be small, and resistance to water, pressure and heat is demanded. Sensitivity of the sensor is determined finally by noise level in a detection circuit. The sensor`s minimum detection capability was 40 mgal in the case of the distance between a weight and an electrode being 3 {mu}m. This specification value is a value realizable by the current micromachining technology. Dimensions for the weight and other members were decided with the natural frequency to make band width 2 kHz set to 4 kHz. Completion of the product has not been achieved yet, however, because of a problem that the weight gets stuck on the electrode plate in anode bonding in the assembly process. 7 refs., 5 figs., 1 tab.

  2. Three dimensional numerical modeling for investigation of fracture zone filled with water by borehole radar; Borehole radar ni yoru gansui hasaitai kenshutsu no sanjigen suchi modeling

    Sanada, Y; Watanabe, T; Ashida, Y [Kyoto University, Kyoto (Japan); Hasegawa, K; Yabuuchi, S [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)


    Water bearing fracture zones existing in rock mass largely influence the underground water flow and dynamic property of rock mass. The detailed survey of the location and size of water bearing fracture zones is an important task in the fields such as civil engineering, environment and disaster prevention. Electromagnetic waves of high frequency zones can be grasped as a wave phenomenon, and the record obtained in the actual measurement is wave forms of time series. In the exploration using borehole radar, this water bearing fracture zone becomes the reflection surface, and also becomes a factor of damping in the transmitted wave. By examining changes which these give to the observed wave forms, therefore, water bearing fracture zones can be detected. This study made three dimensional numerical modeling using the time domain finite difference method, and obtained the same output as the observed wave form obtained using borehole radar. By using this program and changing each of the parameters such as frequency and resistivity in the homogeneous medium, changes of the wave forms were observed. Further, examples were shown of modeling of detection of water bearing fracture zones. 5 refs., 16 figs., 1 tab.

  3. Archaeological prospecting using electrical resistivity method. Case history of Kaibukiyama ancient tomb; Denki tansaho ni yoru iseki tansa. Kaibukiyama kofun no chosarei

    Mizunaga, H; Ushijima, K; Kishikawa, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    To grasp the three-dimensional structure of ancient tomb during the archaeological prospecting of Kaibukiyama ancient tomb, various electrical resistivity methods were tried. For the survey, firstly, in order to clarify the electrical resistivity structure of rear circular part of ancient tomb, roughly, mapping was conducted by means of two-electrode method using a multi-channel measuring system. Then, the vertical prospecting was conducted densely with a mesh form having VES intervals of 2 m as a detailed survey by means of Schlumberger method. For the three-dimensional inverse analysis of apparent electrical resistivity data by the two-electrode method, a program with high calculation speed was developed by using algorithm where Jacobian with a homogeneous model is adopted for the Jacobian calculation. As a result of the analysis, an outline of underground 3-D resistivity structure was determined. The resistivity anomaly with high values obtained from the results of 2-D inverse analysis of VES curve by means of Schlumberger method agreed well with the central part of the ancient tomb, which was confirmed during the archaeological survey. 4 refs., 8 figs.

  4. Recognition and detection of seismic phases by artificial neural network detector; Jinko neural network ni yoru jishinha no ninshiki to kenshutsu

    Yamazaki, K; Wang, W [Tokyo Gakugei University, Tokyo (Japan)


    Initial parts of P-waves, medium or high in intensity, are detected using an artificial neural network (ANN). The ANN is the generic name given to information processing systems of the non-Neumann type configured to human brain in point of information processing function, and is packaged into computers in the form of software capable of parallel processing, self-organizing, learning, etc. In this paper, a hierarchical ANN-assisted seismic motion recognition system is constructed on the basis of an error reverse propagation algorithm. It is reported here, with a remark that this study wants much more data from tests for the evaluation of the quality of the recognition, that P-wave recognition has been achieved. When this technique is applied to the S-wave, much more real-time information will become available. For the improvement of the system, a number of problems have to be solved, including the establishment of automatic refurbishment through adaptation-and-learning and configuration that incorporates frequency-related matters. It is found that this system is effective in seismic wave phase recognition but that it is not suitable for precision measurement. 7 refs., 4 figs.

  5. Laboratory study on streaming potential for exploring underground water flow; Shitsunai jikken ni yoru ryudo den`i wo mochiita mizu michi tansa no kanosei no kento

    Sato, H; Shima, H [Oyo Corp., Tokyo (Japan)


    To investigate a possibility of exploration of underground water flow as well as to grasp the underground fluid flow by measuring streaming potential at the ground surface, some experiments were conducted using a model unit by considering the difference of permeability. For this experimental unit, water is driven by adding head difference between the polyethylene vessel filled with water and the experimental water tank. The size of water tank is 350{times}160 mm with a height of 160 mm. Twenty platinum electrodes are set on the cover of water tank. Toyoura standard sand and Kanto loam were used for the experiments. For the experiments, fluid was injected in various combined models by considering the permeability, to measure the streaming potential. As a result, it was explained by the streaming potential that the fluid flows in a form of laminar flow in the experimental water tank, and that the movement of fluid in the Kanto loam is quite slow. It was also confirmed that the streaming potential method is an effective technique for grasping the movement of fluid. 3 refs., 8 figs.

  6. Case study of geostructural prospect of a tunnel by using geophysical methods; Butsuri tansa ni yoru tunnel chisan yosoku to jissai

    Ueda, H [Japan Railway Construction Public Corp., Tokyo (Japan); Kawakami, J [Taisei Construction Corp., Tokyo (Japan); Nagasue, I; Hiwatashi, S; Wakuno, M [Oyo Corp., Tokyo (Japan)


    A preliminary survey was carried out by combining elastic wave exploration (using a refraction method) and electrical exploration (using a resistivity imaging method) on a long tunnel planned in a granite distributed area. This paper describes a case of verifying geological condition in the area by using a trial survey well and horizontal boring. This tunnel goes through the Seburi mountainous area on the border of Fukuoka Prefecture and Saga Prefecture for a total distance of 12 km. The refraction method and the resistivity imaging method were selected from the necessity of identifying the weathering condition in natural ground, and distributions of fault crush zones and underground water in a section extending 560 m from the well entrance. As a result of comparing the natural ground condition interpreted from the geophysical survey results with the construction records, the fault was detected as a cracked or deformed section in the part where the resistivity value changes abruptly or where the resistivity is low. The tunnel natural ground classification showed a good correspondence with the elastic wave velocities. The largest flooding section showed a good agreement with the section where the resistivity changes suddenly to a lateral direction. Thus, the geological information interpreted from both surveys presented a good correspondence with the construction records, leading to a judgment that the prediction is possible. 3 refs., 4 figs., 5 tabs.

  7. Computational study on full-wave inversion based on the elastic wave-equation; Dansei hado hoteishiki full wave inversion no model keisan ni yoru kento

    Uesaka, S [Kyoto University, Kyoto (Japan). Faculty of Engineering; Watanabe, T; Sassa, K [Kyoto University, Kyoto (Japan)


    Algorithm is constructed and a program developed for a full-wave inversion (FWI) method utilizing the elastic wave equation in seismic exploration. The FWI method is a method for obtaining a physical property distribution using the whole observed waveforms as the data. It is capable of high resolution which is several times smaller than the wavelength since it can handle such phenomena as wave reflection and dispersion. The method for determining the P-wave velocity structure by use of the acoustic wave equation does not provide information about the S-wave velocity since it does not consider S-waves or converted waves. In an analysis using the elastic wave equation, on the other hand, not only P-wave data but also S-wave data can be utilized. In this report, under such circumstances, an inverse analysis algorithm is constructed on the basis of the elastic wave equation, and a basic program is developed. On the basis of the methods of Mora and of Luo and Schuster, the correction factors for P-wave and S-wave velocities are formulated directly from the elastic wave equation. Computations are performed and the effects of the hypocenter frequency and vibration transmission direction are examined. 6 refs., 8 figs.

  8. Fault detection by Turam TEM survey. Numerical model studies and a case history; TEM ho Turam sokutei haichi ni yoru danso kenshutsu no kokoromi. Model keisan to jisshirei

    Wada, K; Tsutsui, T [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan); Ito, T [Chiba Univ., Chiba (Japan). Faculty of Science; Takeuchi, A [Toyama University, Toyama (Japan). Faculty of Science; He, P [Power Reactor and Nuclear fuel Development Corp., Tokyo (Japan)


    With an objective to detect faults estimated to exist along the Shigesumi valley in the Kamioka mine, discussions were given by using electromagnetic survey, which uses the Turam measurement arrangement based on the TEM method, and three-dimensional model calculations. The Turam measurement arrangement, which installs transmission loop fixedly, is used to identify nature and distribution of electrically conductive objects upon noticing abnormal portions in magnetic fields in the measurement data. In the model calculation, the plate model calculation method and the FDTD method were used, and so was the calculation code TEM3DL. The result revealed that strong topographical influence is seen from steep V-shaped valley existing along the traverse line in the measurement data, but an abnormal resistivity band accompanying remarkable distortion in the curve was detected. According to the result of the model calculation, anomaly detection may be found difficult in locations where a low resistivity band has not grown enough locally. It was possible from these facts to assume a model in which the low resistivity band exists directly below the Shigesumi valley, suggesting existence of faults. 2 refs., 8 figs.

  9. Nodal head method with matric operation in analysis of mine ventilation networks. Matrics kaiho wo mochiita setten ho ni yoru tsuki mo kaiseki

    Sasaki, K.; Miyakoshi, H. (Akita Univ., Akita (Japan). Mining College); Kinoshita, H.; Onozuka, T. (Hanaoka Mining Co. Ltd., Akita (Japan))


    In this report, the method of analyzing mine ventilation networks is explained in which the direct matric operation method is applied to the solution of the linear equation system introduced from the fundamental equation of the nodal head method. In other words, the fundamental equation was expressed by genelarized equation composition by using connecting functions between nodes and the algorism of a computer program was clarified. And the calculation method necessary for other ventilation netwrks analysis was shown in a concrete form. For solving the linear equation system, the matric operation method based on the modified Choleski's method was used in order to speed up the calculation and stabilize the convergence process of the solution. As examples, calculation was made on the ventilation networks of total numbers of the nodes of 8, 14, 51 and 141. From these ventilation network analyses, using a linear equation system concerning the nodal pressure correction, it was found that in the system with convergence acceleration coefficient of 1.4, the number of sequential repeating frequency of approximation Mc which was required for convergence was in the order of Mc {approx equal} 13 (cycle) for the condition that the fan pressure was constant and the convergence condition was {vert bar} AQi {vert bar}{sub max} {lt} 0.1m {sup 3}/min. 14 refs., 12 figs., 3 tabs.

  10. Evaluation of flux-trapping and magneto-resistibility of superconductors by ESR spectroscopy; ESR ho ni yoru chodendotai no jisoku hosoku to taijiba tokusei no hyoka

    Kusumori, T; Matsuura, K; Muto, H [National Industrial Research Institute of Nagoya, Nagoya (Japan)


    The abnormal sisal, which was observed in the ESR measurement of superconductors, was confirmed to be a non-ESR (non resonant) signal, from an ESR experiment applying parallel and vertically polarized microwave fields and from the calculation of the ESR transition probabilities. The field modulation dependence of the spectra revealed that the signal was composed of two components. From the modulation-scheme analysis and a study of type I and II superconductors, two components were assigned to the microwave responses to magnetizations trapped in the crystalline portion and at intergranular Josephson junctions. The former B and the batter J components are observed in the first derivative and absorption a form, respectively, and their polarities differently behave for the field sweep reversal. Based on these results, we have improved an ESR spectrometer, which makes it possible to measure separately two kinds of magnetization and to study the trapping ability and quantum flux. 11 refs., 12 figs., 1 tab.

  11. Thermochemical recuperative combined cycle with methane-steam reforming combustion; Tennengasu kaishitsu nensho ni yoru konbaindo saikuru hatsuden no kokoritsuka oyobi denryoku fuka heijunka taio

    Kikuchi, R.; Essaki, K.; Tsutsumi, A. [The University of Tokyo, Tokyo (Japan). Dept. of Chemical System Engineering; Kaganoi, S.; Kurimura, H. [Teikoku Sekiyu Co., Tokyo (Japan); Sasaki, T.; Ogawa, T. [Toshiba Co., Tokyo (Japan)


    Thermochemical recuperative combined cycles with methane-steam reforming are proposed for improving their thermal efficiency and for peak-load leveling. For targeting higher thermal efficiency, a cycle with methane-steam reforming reaction heated by gas turbine exhaust was analyzed. The inlet temperature of gas turbine was set at 1,350 degree C. Low-pressure steam extracted from a steam turbine is mixed with methane, and then this mixture is heated by part of the gas turbine exhaust to promote a reforming reaction. The rest of the exhaust heat is used to produce steam, which drives steam turbines to generate electricity. The effect of steam-to-methane ratio (S/C) on thermal efficiency of the cycle, as well as on methane conversion, is investigated by using the ASPEN Plus process simulator. The methane feed rate was fixed at constant and S/C ratio was varied from 2.25 to 4.75. Methane conversion shows an increasing trend toward the ratio and has a maximum value of 17.9 % at S/C=4.0. Thermal efficiency for the system is about 51 % higher than that calculated for a conventional 1,300 degree C class combined cycle under similar conditions. A thermochemical recuperative combined cycle is designed for peak-load leveling. In night-time operation from 20 : 00 to 8 : 00 it stores hydrogen produced by methane steam reforming at S/C=3.9 to save power generation. The gas turbine inlet temperature is 1,330 degree C. In daytime operation from 8 : 00 to 20 : 00 the chemically recuperated combined cycle operated at S/C=2.0 is driven by the mixture of a combined cycle operated at constant load with the same methane feed rate, whereas daytime operation generated power 1.26 times larger than that of the combined cycle. (author)

  12. FY1995 report on the analyses of functional living systems using magnetic stimulation and magnetic fields; 1995 nendo jiki shigeki oyobi kyojiba ni yoru seitai kino kaimei



    The purpose of the project is to widen the understanding of the biological effects o magnetic fields and to search potential applications of biomagnetics to medical diagnosis and treatments. We developed a method of localized magnetic stimulation of the brain. By concentrating induced eddy currents on a target with a pair of opposing pulsed magnetic fields produced by a figure-eight coil, they were able to stimulate the human cortex within a 5 mm resolution. We studied the properties of diamagnetic water in static magnetic fields. The phenomenon that the surface of the water was pushed back by magnetic fields of higher gradients was observed. The behavior of oxygen dissolved in an aqueous solution under magnetic fields of up to 8T with a gradient of 50T/m was studied. For oxygen concentrations greater than 11 mg/l, a clear redistribution of dissolved oxygen was observed. Effects of strong magnetic fields on a process of dissolution of fibrin clots was studied. Fibrin polymers in water magneto-phoresically drifted in the direction of increasing magnetic fields, and dissolution of fibrin polymers by plasmin was accelerated. (NEDO)

  13. Buckling collapse analysis of framed structures by using adaptively shifted integration technique. Junnogata shifted intergration ho ni yoru honegumi kozo no zakutsu hokai kaiseki

    Toi, Y.; Isobe, D. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)


    This paper describes the following matters on application of an adaptively shifted integration technique to a buckling collapse analysis of framed structures: This method is a method in a finite element analysis using three-dimensional girder elements to arrange value integration points at optimal locations in a linear analysis if the elements are in an elastic transform condition on the whole. The method then moves the value integration points so that plastic hinge will occur in these locations immediately after part of the elements has yielded. The method was applied to analyzing an elastic buckling problem in several loading patterns for either a both-end supported or a one-end fixed beam member. A result was obtained that a number of elements required for one member is four at minimum. In a buckling analysis of framed structures, a satisfactory result was obtained by using an automatic element segmenting algorithm, which begins the analysis with one element one member, and immediately after a member is determined with a possibility of generation of buckling, splits that member only into four elements. 6 refs., 5 figs.

  14. Improvement of D.I. diesel engine combustion using numerical simulation; Chokufun diesel kikan no nensho kaizen shuho. Suchi kaiseki ni yoru torikumi

    Minami, T.; Adachi, T.; Isyii, Y. [Isuzu Motors Ltd., Tokyo (Japan)


    For the purpose of improving DI diesel engine combustion, it is important to predict air flow of intake and exhaust manifold, intake port flow, combustion chamber swirl and fuel spray combustion. This paper describes the application of numerical simulation to the engines, the analysis of phenomena and a problem of simulation model modification. (author)

  15. Application of monolithic lining to tundish and extension of tundish life with improvement of refractories; Tandeisshu futeiseika to taikabutsu kaizen ni yoru jumyo kojo

    Mori, Eiichiro; Fujta, Takashi; Tanikawa, Kanji [Kobe Steel Corp., Hyogo (Japan)


    As a part of realization of monolithic liming of a tundish lining refractory, a study on 2CC and 3CC tundish monolithic refractories was carried out to improve placing efficiency and extend its life. Main inspection points were set on (1) casting facility specifications and (2) structure and material. A force feeding pump system with a high degree of freedom for placing layout was selected. It was judged preferable than a hopper dolly type ladle repair facility in the degree of freedom for a placing site and facility expenses, though little inferior at maintenance. A force feeding pump is combined with a boom to enable the facility to cast for plural objects. Low expansion and creep properties were given to the refractory by reviewing the addition of the expansive material and the structure was improved by setting anchor blocks at corner parts. The cost of refractories was reduced and labor saving of refractory placing workers was achieved by widely extending the life. (NEDO)

  16. Life prolongation and cost reduction of steel ladles with improving refractories and their structure; Taikabutsu zaishitsu to kozo kaizen ni yoru shuka taikabutsu no chojumyoka to kosuto teigen

    Nakai, Masato; Kasahara, Hajime; Fukutani, Fujio; Imai, Hiroyuki [Nippon Steel Corp., Tokyo (Japan)


    Steel Making Plant, Hirohata Iron Works, Nippon Steel Corp. succeeded to reduce the cost of furnace materials by measures described below down to 49% compared to that in 1992. (1) For tuyre bricks, cleanability against oxygen was improved by compacting by vacuum cast forming. (2) For SL bricks, the cost was reduced by applying imported bricks and optimization of the range of use. (3) For alumina-magnesia amorphous refractories for side walls, low expansion and breaking resistance were improved by optimization of magnesia quantity and silica ultra fine powder quantity. (4) For side wall structure, improvement of tie-in between the ground part and the side wall and lining with efficient thickness were carried out. (NEDO)

  17. Improvement of efficiency by proportional and integral control for compact boiler; Shoyoryo boiler no renzoku seigyo (P.I seigyo) ni yoru seino kaizen

    Yanagida, T. [Kawasaki Thermal Engineering Co. Ltd., Shiga (Japan)


    Efficiency of a compact boiler is improved by the introduction of a continuous P.I. control. It is controlled by the following procedure. The proportional control, which controls magnitude of combustion in proportion to a load requirement, is combined with an integral control function which keeps steam pressure at a given level, in order to stabilize steam pressure at a level comparable to that of a large, water-tube type boiler. A stable steam pressure is realized by including control of make-up water supply, to minimize the effects of water supply on steam pressure. The effects of characteristics of the combustion valve on control are relaxed by programming. In addition to the above, rotational speed of the motor for the forced draft fan is controlled for each load level, to reduce power consumption. These bring improved quality of steam, i.e., stabilized steam pressure, improved follow-up characteristics of the steam and secured dryness of the steam. Energy-saving is also achieved, i.e., reduction of noise and power consumption at a low combustion load are achieved by improved real boiler efficiency and inverter-aided control of the forced draft fan. Low-NOx burners are adopted, to abate NOx content to 60ppm or less at any load. 16 figs.

  18. Adaptive feedforward control for improving output power response of CO2 laser; Tekiogata feedforward ni yoru laser shutsuryoku oto no kaizen

    Imai, Y.; Takahashi, t.; Morita, A. [Mitsubishi Electric Corp., Tokyo (Japan)


    Feedback control has been used to stabilize the steady-state output power of a CO2 laser to overcome the problems caused by the change in the temperature/deterioration of CO2 gas. The transient response, however, is as slow as a few hundred milliseconds because of the slow dynamics of a thermopile power sensor. When machining conditions of a CO2 laser are changed, this rather slow response requires an extra dwell time, resulting in low productivity of the machining. To cope with this problem, the authors have developed adaptive feedforward control for a CO2 laser in addition to conventional feedback control. The model of a CO2 laser is described as a gain, which is varied by the setting parameters; laser power, pulse frequency and duty factor, as well as gas conditions. In this paper, two new variables, effective discharge power and threshold discharge power, are introduced to obtain a compact and adjustable model. With the proposed control system, the step response time of a laser power is reduced to less than ten milliseconds without overshoot, and can be set to desired constant time. The effects of such a fast and stable response on the machining speed and machining quality are examined. The experimental results show that for thin metal line-cutting, neither the melt-off area nor dross is observed even in the no-dwell time case. For thin metal hole-cutting, the machining speed is improved by 30%. 11 refs., 14 figs., 3 tabs.

  19. Improvement of In2O3-based CO sensor by using surface modifiers; Hyomen shushokuzai ni yoru sanka injiumukei soshi no CO kenchi tokusei no kaizen

    Yamaura, H.; Miura, N.; Amaze, N. [Kyushu University, Fukuoka (Japan); Tamaki, J. [Ritsumeikan University, Kyoto (Japan); Moriya, K. [Osaka Gas Co. Ltd., Tokyo (Japan)


    Aiming at developing a semiconductor CO sensor applicable to the safety control of gas appliances, we carried out an extensive material search for promoters to In2O3-based elements. Among the elements added (0.5 wt%) with each of 12 transition metal oxides, the Co3O4-added one was outstanding in sensitivity and selectivity to CO at 200degC. Remarkably the sensing properties of this element could be improved further by the addition of Au (0.04 wt%). The doubly promoted element, Au(0.04 wt%)-Co(0.5 wt%)-In2O3, gave excellent characteristics in sensitivity to CO, selectivity to CO over H2 and other selected gases, and response rates at 250degC. The promoting effects of the additives were shown to originate from the proper enhancement of catalytic activity for CO oxidation. 11 refs., 9 figs.

  20. Improvement in mechanical properties of chromium-nickel sintered compacts by repeated rolling and annealing; Kuromu nickel shoketsuzai no kurikaeshi atsuen shodon ni yoru kikaiteki seishitsu no kaizen

    Harada, Y. [Toyohashi University of Technology, Aichi (Japan); Omori, M. [Hiroshima-Denki Institute of Technology, Hiroshima (Japan); Ando, H. [Nippon Steel Glass Co. Ltd., Tokyo (Japan); Matsui, H. [Tadano Ltd., Kagawa (Japan); Okita, T. [Honda R and D Co. Ltd., Tokyo (Japan)


    Chromium-nickel sintered compacts containing 50 and 80 mass%Cr were tried to improve their mechanical properties by means of a thermo-mechanical treatment, i.e., repeated rolling and annealing. Specimens from the as-sintered compacts showed no ductility at room temperature and small ductility at temperatures higher than 1000 K because of poor alloying of nickel with chromium. Tensile properties of the sheets repeatedly rolled with the intermediate annealing at 1173 K were very similar to those of the as-sintered specimen. While the sheets rolled with the annealing at 1573 K were excellently improved in their strength and ductility due to the considerable interdiffusion of chromium and nickel. The intermediate temperature embrittlement, that is, the ductility minimum well observed around 1000 K in a chromium-nickel alloy appeared also in the sheets rolled with the annealing at 1573 K. 15 refs., 13 figs., 1 tab.

  1. Improvement of lean combustion characteristics of heavy-hydrocarbon fuels with hydrogen addition; Suiso tenka ni yoru kokyu tanka suisokei nenryo no kihaku nensho no kaizen

    Sakai, Y. [Saitama Institute of Technology, Saitama (Japan); Ishizuka, S. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering


    The Lewis numbers of lean heavy-hydrocarbon fuels are larger than unity, and hence, their flames are prone to extinction in a shear flow, which occurs in a turbulent combustion. Here, propane is used as a representative fuel of heavy-hydrocarbon fuels because the Lewis number of lean propane/air mixtures is larger than unity, and an attempt to improve its combustion characteristics by hydrogen addition has been made. A tubular flame burner is used to evaluate its improvement, since a rotating, stretched vortex flow is established in the burner. The results show that with' hydrogen addition, the fuel concentration, the flame diameter and the flame temperature at extinction are reduced and its combustion characteristics are improved. However, it is found that the effective equivalence ration at extinction cannot become so small as that of lean methane/air mixture, which has a Lewis number less than unity. (author)

  2. Improvement of wells turbine performance by means of 3D guide vanes; Sanjigen annai hane ni yoru wells turbine seino no kaizen

    Takao, M.; Kim, T.H. [Saga University, Saga (Japan); Setoguchi, T. [Saga University, Saga (Japan). Faculty of Science and Engineering; Inoue, M. [Kyushu University, Fukuoka (Japan). Faculty of Engineering


    Performance of a Wells turbine was improved by equipping 3D guide vanes before and behind a rotor. For further improvement, 3D guide vanes have been proposed in this paper. The performance of the Wells turbine with 2D and 3D guide vanes have been investigated experimentally by model testing under steady flow conditions. Then, the running and starting characteristics in irregular ocean waves have been obtained by a computer simulation. As a result, it is found that both of the running and starting characteristics of the Wells turbine with 3D guide vanes are superior to those of the turbine with 2D guide vanes. (author)

  3. Stall margin improvement of an axial flow fan with end wall injection and suction; Hekimen fukidashi suidashi ni yoru han'yo jikuryu sofuki no shissoku kaizen

    Nishioka, K.; Kuroda, H.; Obata, S.; Chimura, O. [National Defense Academy, Kanagawa (Japan)


    The experimental studies are conducted to reveal the mechanism of stall margin improvement of an axial flow fan by injection or suction from the end wall. In case of injection, the largest improvement is obtained by the injection at about 0. 14 {approx} 0 .21 times axial chord length downstream from leading edge. The reason for large improvement is that stall vortex, shed intermittent separation vortex and tip leakage vortex are dissipated by this injection, and also that this blowing suppresses the separation of boundary layer. In case of suction, the largest improvement is found for the suction from the end wall near leading edge. The amplitude of periodic static pressure after stall inception becomes smaller in comparison with injection cases. These effects are increased with the increase of suction flow rate, because the discharge of the vortex occurs more easily. On the other hand, the suction from the upstream of leading edge reduces the axial velocity near rotor tip, and then it induces stall. Also we tried to visualize the tip region flow, The suppression mechanism is discussed based on the visualization. The suppression of stall is successfully photographed. (author)

  4. Life prolongation of hot metal ladle by improved shape and material of the bricks; Renga keijo to zaishitsu kaizen ni yoru yosenka jumyo no encho

    Miwa, Toru.; Mori, Hajime.; Fukushima, Hironori.; Iiyama, Makoto. [NKK Corp., Tokyo (Japan)


    Keihin Works, NKK, intended to extend life of a hot metal ladle and reduction of refractory cost by improving shapes and materials of bricks. The refractory composition of the ladle is a 4-layer structure constituted of a permanent lining comprising 3 layers of agalmatolite bricks and a 180 mm thick work lining. High alumina bricks are used for a free board part and Al{sub 2}O{sub 3}-SiC-C bricks for the slag line part to the ground part. Elevation of the pore rate was observed from the working face to the back face in a brick after use. The former is considered caused by densification of structure and the latter by embrittlement by oxidation. Cracks parallel to the working face are considered caused by structural spalling by the difference of the physical properties. Since cracks vertical to the working face are observed, the finite element method (FEM) thermal stress analysis is applied to inspect the possibility of cracks by thermal stress. A brick whose degree of sintering was suppressed was tri allyl manufactured. It brought wide extension of life and reduction of refractory cost. (NEDO)

  5. Stall margin improvements of conventional axial flow fans with the reformed casingtreatments; Casingtreatment ni yoru han`yo jikuryu sofuki no shissoku kaizen

    Nishioka, K.; Kuroda, H.; Obata, S.; Chimura, O. [National Defense Academy, Kanagawa (Japan); Takeishi, M.


    At the first part of this paper, the experiments and results to the blowing and suction on a fan are presented, and it is found that blowing toward the down stream direction are more effective and blowing location is suitable on the leading edge side of blades. On basis of these results, the reformed casingtreatments which the blowing air from the slots makes the large relative momentum for blade chord are build, and the experiments using the two conventional fans equipped with the reformed casingtreatment and conventional one are performed. So, the very large stall margin improvements (about 1.7 times) and about 0.5% efficiency penalty of 10% stall margin improvement at design flow rate are obtained for the reformed casingtreatment. 10 refs., 15 figs., 1 tab.

  6. Improvements of diesel combustion with pilot and main injections at different piston positions; Piston iso wo koryoshita pilot funsha ni yoru diesel nenshono kaizen

    Li, C.; Ogawa, H.; Miyamoto, N. [Hokkaido University, Sapporo (Japan); Sakai, A. [Nissan Motor Co. Ltd., Tokyo (Japan)


    The fuel spray distribution in a DI diesel engine with a pilot injection was actively controlled by pilot and main fuel injections at different piston positions to avoid the main fuel injection from hitting the pilot flame. A CFD analysis demonstrated that the movement of the piston with a cavity divided by a central lip along the center of the sidewall effectively separated the cores of the pilot and main fuel sprays. The experiments showed that more smoke was emitted with pilot injection in an ordinary cavity without the central lip while smokeless and low NO{sub x} operation was realized with pilot injection in a cavity divided by a central lip even at heavy loads where ordinary operation without pilot injection emitted smoke so much. The indicated specific energy consumption ISEC was a little bit higher with the pilot injection, mainly because of the reduction in the degree of constant volume combustion. With the advanced pilot injection, ISEC was improved more than that with the retarded pilot injection while the NO{sub x} is a little higher than the retarded pilot injection maintaining still much lower than in ordinary operation. (author)

  7. New method for 3-dimensional visualization of distributed gas using laser ultrasonic technique; Laser choonpaho ni yoru gas no 3 jigen kukan bunpu keisoku

    Ochiai, M.; Kubo, K.; Kanemoto, S. [Toshiba Corp., Tokyo (Japan); Kokubo, T. [Tokyo Electric Power Co., Inc. (Japan)


    In case that detection of gas leak is performed applying gas sensors, not only sensing for extremely small amount of gas but also measurement of spatial distribution state from the viewpoint of identification of leaking places are important. Meanwhile, it is known that the methane, main component in fuel gas, has characters which absorbs ray having certain specific wavelength and in addition emits its absorbed energy acoustically. As to a photo-acoustic effect in an open space, it is newly found that the signal has a frequency of about 40 kHz and a propagation directivity which is perpendicular to the laser axis. In the feasibility test based on this property, methane molecules are excited by an optical parametric oscillator (OPO) type laser source which has a wavelength of 1330 micron and an output power of about 5 mJ/pulse. Array microphones and 2-dimensional laser scanning system are used for detecting the gas distribution. In the next place, owing to analyzing phase differences of sound wave on the basis of oscillation time of pulse laser, it was verified that the 3-dimensional distribution of gas was measurable. 8 refs., 9 figs., 2 tabs.

  8. Stereo-selective hydrolytic reaction of toxic compounds by enzyme immobilized on porous ceramics; Takoshitsu ceramics kotaika koso ni yoru dokusei kagobutsu no rittai sentakuteki kasui bunkai hanno

    Kato, K.; Saito, T. [National Industrial Research Institute of Nagoya, Nagoya (Japan)


    Experiment was made on stereo-selective hydrolytic reaction of trifluoroethyl ester of ketoprophene by various kinds of lipase. In addition, study was made on the stability of lipase simply immobilized on porous ceramics under the existence of organic solvent. In the experiment, the hydrolytic activity of 8 kinds of lipase was studied for ketoprophene monochloroethyl ester (1a) and trifluoroethyl ester (1b). The experiment result showed that lipase M originating in mold (Mucor Javanicus) shows a high reactivity and stereo-selectivity for the compound (1a). The lipase immobilized on porous ceramics was easily obtained by a very simple method composed of only throwing carriers into enzyme suspension, agitation and refrigerated drying. The lipase immobilized on porous ceramics 'Toyonite 200-A' synthesized from kaolinite retained the residual activity of nearly 50%, original selectivity and considerable stability after 5 times of repetitive uses. This study result is useful for bio- reactors and bio-sensors for synthesis or decomposition of compounds. (NEDO)

  9. Flows around a moving flat plate simulated by the method of cellular automata. Seru outoman ho ni yoru ido heiban mawari no nagare

    Tsutahara, M; Tomiyama, A; Kimura, T; Murata, H [Kobe University, Kobe (Japan). Faculty of Engineering


    In order to analyze the field of flow containing a moving boundary by the method of cellular automaton, the method of giving the boundary conditions in the case where a wall is moving at a constant velocity in the normal direction was examined. This method is used to simulate the movement of continuous fluid by statistically treating the movement of many discrete particles which repeat translation and collision. The collision law of particles at grid points is formulated so as to conserve mass(number of particles) and momentum for the purpose of satisfying the governing equation of flow. The object is the flow in the case where a flat plate moves in the normal direction inside the fluid enclosed by rectangular walls and the plate was assumed that it is first in a standing condition, then starts to move from left to right at a speed of V and stops in front of the right wall. Three boundary conditions, surrounding wall, plate in the standing condition and moving plate, were considered. Flow rates were calculated concerning the translation and collision and each divided mean-field-approximation region(space having a magnitude of capable of averaging operation of particles). Effectiveness of proposed boundary conditions was confirmed by a visualization experiment. 3 refs., 14 figs.

  10. Electrostatic settling of catalyst particles in hydrogenation of methyl benzoate. Denkai chinkoho ni yoru ansokukosan mechiru suisoka hannoeki kara no shokubai ryushi bunri

    Kato, K. (Japan Energy Corp., Tokyo (Japan). Central Research Lab.)


    As benzyl alcohol (BA), which is one of the simplest alcohol having aromatic ring, has been used widely for the fields related to soap, perfume and chemicals industry, its usage has not always been so much because of its expensiveness. Authors developed previously a new process technique to produce cheaper and higher purity BA not through chlorination process using toluene as its raw materials. The BA can be obtained by hydrogenating methyl benzoate (MB) at a dispersion babble tower using cupper-chromium type powder catalyst in mixed solvent of methanol and toluene. The catalyst becomes much fine particles after the reaction. In this study, it is examined to separate MB hydrogenation reaction solution obtained by electrostatic settling into solid and liquid phases as an aim to improve the BA production process. Rate of electrostatic settling does not depend upon solid concentration, slurry forming conditions, electrode materials, specific resistance of slurry layer and others, but is in proportion to electric field intensity. Furthermore, process of the electrostatic settling is expressed by an equation. 9 refs., 9 figs., 3 tabs.

  11. Development of small-size transmission tower erection method; Kogata tetto kumitate koho no kaihatsu kenkyu (gaibushiki crane ni yoru kogata tetto kumitate koho no kaihatsu)

    Matsuishi, S.; Asano, J.; Koji, Y. [Kansai Electric Power Co. Inc., Osaka (Japan); Tsujimura, I.; Teramoto, A. [The Kanden Kogyo Incorporated, Osaka (Japan); Sasaki, T.; Mito, K. [AG Ajikawa Corp., Osaka (Japan); Tsuji, M.; Fukumoto, T.; Yamaguchi, N.


    To reduce the construction period and cost and to enhance the safety during 77 kV-class transmission tower election, a new method of small steel transmission tower erection using an external type crane has been developed. For the selection of cranes, a commercially available self-climbing crane was employed which has an operating radius of 11 m, a lifting load capacity of 1.5 t, and a lift of up to 60 m. For the space analysis using a model tower, various supporting methods with horizontal supporting members, stress analysis for each tower stub, and apparatuses were examined. For the demonstration tests of election using the model tower, strain gages were attached at each point of steel tower, crane and horizontal supporting members, to measure the stress of members at each stage of the election. It was confirmed that there were no problems. For the election of actual steel tower, the practicality of this method was compared with that of conventional methods. The construction period was reduced in 20%, and the cost was reduced in 4%. The safety of this method was drastically enhanced due to the lack of moving on the tower and less manual operation. 9 figs., 1 tab.

  12. Simultaneous reduction of NOx and smoke using stratified charge compression ignition; Sojo kongoki no asshuku chakka ni yoru NOx smoke no doji teige

    Hashizume, T.; Miyamoto, T.; Akagawa, H. [New ACE Institute Co. Ltd., Ibaraki (Japan); Tsujimura, K. [Chiba Institute of Technology, Chiba (Japan)


    Simultaneous reduction of NO{sub x} and smoke under high load conditions could be obtained by MULDIC (MULtiple stage DIesel Combustion) where mixture was made stratified before ignition. In this investigation of the basic characteristics of MULDIC, gaseous fuels (DME, Propane) were charged into the intake air which led to the creation of homogeneous lean mixture, and liquid fuel was injected into the cylinder and made rich mixture. The results of the engine test showed that NO{sub x} emissions could be reduced to less than 100 ppm and smoke emissions were also maintained 0 FSN even at higher loads. Moreover, homogeneous rich mixture test results showed that low smoke combustion could be obtained under equivalence ratio of 1.6. In MULDIC, increasing the ignition delay period of injected fuel, soot formation rate was decreased, because over rich region was avoided. (author)

  13. Application of adaptive control to windmill power system by computer simulation. Simulation ni yoru tekio seigyo no furyoku hatsuden system eno oyo

    Tomiya, T.; Matsuo, T. (Anan College of Technology, Tokushima (Japan)); Suzuki, T.; Kamano, T. (Tokushima University, Tokushima (Japan). Faculty of Engineering)


    A windmill power system using load DC generators having resistive load was subjected to discussions by simulation on development of a control method and its output characteristics to draw out the wind energy effectively even when the system characteristics are unknown. The control method used is a mountaineering method available among adaptive control methods. As a result of discussions, the effectiveness of the mountaineering method was confirmed in controlling the output either when the wind velocity is constant or variable. With respect to the control interval, which is a problem in carrying out a control, it was found that the control output stabilizes as the control interval is increased when the wind velocity is constant, but takes longer time before reaching a steady state output. When the wind velocity is variable, the increased control interval reduces the output slightly because of the load resistance change becoming coarser. It was also revealed that, on simulated natural winds, this control method can draw out more energy than by a fixed load resistance. 7 refs., 11 figs., 1 tab.

  14. Removal of minute amount of furfural in ethanol aqueous solution by use of batch-rectification; Kaibun seiryu ni yoru ethanol suiyoekichu no biryo furfural no jokyo

    Nakano, K.; Shimoda, M.; Uemura, Y.; Hatate, Y. [Kagoshima University, Kagoshima (Japan). Faculty of Engineering


    Furfural is produced in the distillation stage of low-class distilled spirit manufacturing and badly influences the quality of products. The removal of minute amount of furfural in an ethanol aqueous solution was thus investigated by an Oldershow-type batch-rectifying column consisting of ten plates. Furfural of 50 ppm was added to an ethanol aqueous solution of 6.6 mole% as raw materials. If the ethanol concentration in the upper distillation plates is set high, furfural is forecast to be concentrated in the intermediate plate. In an experiment, side-cut was carried out at this plate. If side-cut is performed at the seventh-plate tray from the top, the total side-cut rate is 12%. In this case, 77% of furfural is removed. The side-cut rate of ethanol at that time was 11%. Moreover, 85% of furfural was removed when ethanol with high concentration was extracted from the top under total reflux conditions and when side-cut was carried out. Only 9% of ethanol was distilled in this case. It was confirmed that furfural can be separated using a multi-plate batch-distilling column. 2 refs., 4 figs., 1 tab.

  15. Dynamic stability analysis of circular arch subjected to follower forces with small disturbances; Judo kaju wo ukeru enkei arch no yuran ni yoru doteki kyodo to anteisei kaiseki

    Fukuchi, N.; Okada, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hirano, Y. [Sumitomo Heavy Industries, Ltd., Tokyo (Japan)


    This paper describes the deformation and dynamic stability of circular arch subjected to follower forces in a submerged membrane type marine structure reinforced by arch frames. Governing equations for finite deformations of the circular arch subjected to follower forces are introduced using an embedded curve coordinate, which are formulated by applying Galerkin method. In addition, equations of motion due to small disturbances under given condition of loading are introduced. Based on these equations, dynamic stability of the arch is analyzed by means of Runnge-Kutta-Gill method, to clarify the relationship between disturbances and instability regions and the resulting phenomena. Near the boundary regions of stability, both amplitude and cycle of deformation are greatly affected by the amplitude of disturbances. The dynamic instability is governed by the inverse symmetry primary mode with minimum characteristic frequency which is specific for the circular arch. The dynamic stability has high parameter dependency, and the instability regions have a complicated shapes. Although flattened arch has a smaller static critical load, it provides the dynamic stability against the disturbance. 5 refs., 10 figs.

  16. Development in high speed and high quality laser cutting process in fiber reinforced plastics; FRP no laser ni yoru kosoku, kohinshitsu setsudan gijutsu no kaihatsu

    Ishide, T.; Shirota, H.; Matsumoto, O. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)


    Trimming was performed and studied by cutting KFRP, an epoxy matrix with Kevlar fiber woven thereinto, using various laser beams. The CO2 laser is capable of high-speed cutting but the product is low in quality. The surface of a cut by the YAG laser is not high in quality even with its peak output elevated. The thermally affected area is smaller under the excimer laser but it is low in cutting speed. The ablation properties of the excimer laser were investigated and the beam was shaped into a linear beam for another experiment, but it failed to attain the target speed of cutting. Next, a combination of excimer laser and CO2 laser was used for cutting. It was so designed that the preceding CO2 laser cuts the KFRP at a high speed to leave behind a carbonized layer, which is followed by a linear beam which vaporizes the carbonized layer for removal. An optical system is adopted for reshaping the excimer oscillated beam into a tube-like beam. Optical conditions were determined for a fluence value required for the removal of the carbonized layer. When the CO2 laser was set at 160W and the excimer laser at 20W, a 1mm-thick sheet was successfully cut at a speed of 16.7mm/sec. 3 refs., 7 figs.

  17. Fundamental experiment for flash removal of aluminum alloy by CO2 laser beam cutting; CO2 laser beam setsudan ni yoru aluminium gokin no ibaritori no kiso jikken

    Kataoka, Y.; Tokunaga, T. [University of Industrial Technology, Kanagawa (Japan); Miyazaki, T. [Chiba Institute of Technology, Chiba (Japan)


    CO2 laser beam has been applied to cut of the aluminum alloy. Average cut width, roughness of cut surface and average thickness of heat affected zone are investigated as functions of laser power, cutting speed and assist gas pressure. The average cut width increases with laser power, but it does not depend on the cutting speed. The narrowest average cut width obtained is 0.22mm under the conditions of laser power of 900W and cutting speeds from 600 to 1000mm/min. The roughness of cut surface decreases with decreasing cutting speed. The best smoothness of cut surface obtained is 17 {mu}m (Rmax) , when the conditions are 1100W and 600mm/min. The average thickness of heat affected zone decreases with increasing assist gas pressure. CO2 laser beam cutting is applicable to flash removal from aluminum alloy casting. This process is expected to reduce the need of physical labor and to improve the working conditions in the foundry industry. 32 refs., 10 figs., 2 tabs.

  18. Coal structure construction system with construction knowledge and partial energy evaluation; Kochiku chishiki to bubunteki energy hyoka ni yoru sekitan bunshi kozo kochiku system

    Okawa, T.; Sasai, T.; Komoda, N. [Osaka University, Osaka (Japan). Faculty of Engineering


    The computer aided coal structure construction system is proposed, and a computational construction example is presented. The coal structure construction engine of this system fabricates molecular structure by connecting fragments sequentially inputted through a user interface. The best structure candidate is determined using construction knowledge and partial energy evaluation every addition of one fragment, and this process is subsequently repeated. The structure evaluation engine analyzes the 3-D conformation candidate by molecular dynamics, and evaluates the conformation by determining the energy value of an optimum structure. As an example, this system was applied to construction of coal molecular structure based on the actual data of partial structure composed of 26 structures from 2l kinds of aromatic cluster structures, 27 bonds from 2 kinds of bridged bonds, and 16 groups from 2 kinds of terminal substitutional groups. As a result, this system could construct a superior structure according to expert knowledge from the viewpoint of energy. 6 refs., 5 figs., 2 tabs.

  19. Separation of polyunsaturated fatty acid esters by flowing liquid membrane with porous partition.; Kakumaku gata ryudo ekimaku ni yoru kodo fuhowa shibosan esuteru no bunri

    Yokosawa, R.; Nii, S.; Takahashi, K. [Nagoya Univ., Nagoya (Japan). Depertment of Chemical Engineering; Misawa, Y. [Harima Chemicals, Inc., Osaka (Japan)


    A laboratory-constructed flowing liquid membrane apparatus with porous partition (FLM) was applied to the separation of such polyunsaturated fatty acid esters (PUFA-Ets) as eicosapentaenoic acid ethylester (EPA-Et) and docosahexaenoic acid ethylester (DHA-Et) at 293 K. The hydrophilic porous membrane was used as a partition, and 2 M AgNO{sub 3} aqueous solution was used as a membrane liquid. By using dodecane as a feed diluent and m-xylene as a recovery solution, PUFA-Ets were successfully separated from mixture of fatty acid esters. The recovery fraction of PUFA-Ets and the separation degree between DHA-Et and EPA-Et were investigated ; it increases with the velocity of membrane liquid and the flow path length in the module, while it decreased with the velocity of feed and recovery solution. The recovery fraction of DHA-Et reachs 60% with only 8 s-retention time by the continuous operation. The concentrations of the DHA-Et at the outlet of the module were simulated based on the mass transfer model, which gave nearly 85% recovery fraction with 30 s-retention time. These results show that a stable operation, a high recovery and a high recovery and a high throughput are realized by the FLM. (author)

  20. Reduction of nitrogen in the excretion on Japanese flounder using Ulva and Capitellid; Anaaosa to itogokai ni yoru hirame haisetsubutsuchu no chisso shori

    Honda, H.; Kikuchi, K.; Sakaguchi, I. [Central Research Institute of Electric Power Industry, Tokyo (Japan)


    To develop the culture residue treatment technique using aquatic organisms, the ammonia and nitrate uptake rates of seaweed Ulva and the nitrogen reduction rate of polychaeta annelid Captella sp. with organic sediment predaceous ability were examined in the excretion of Japanese flounder. Nitrogen uptake rate of Ulva was affected by water temperature. It was highest at 20degC, followed at 15degC and 25degC in the order. It was not affected by light intensity between 1500 and 6000 lux. Ammonia and nitrate uptake rates by Ulva were estimated to be 28.2 and 14.6 {mu}g-N/g/h at 20degC under 3000 lux, respectively. Proportion of feces excreted from Capitellid to ingested sediments was 0.38. At 25degC, Capitellid population of one thousand individuals ingested-N at the rate of 24 mg-N/day, and excreted the feces-N of Capitellid at the rate of 7 mg-N/day. About 70% of nitrogen in the sediment was reduced through this process. 15 refs., 9 figs., 13 tabs.

  1. Fracture inspection by BHTV logging through a vinyl chloride tube; Enbi pipe ga sonyusareta kosei deno BHTV ni yoru kiretsu chosa

    Horikawa, H.; Okabe, T.; Takasugi, S. [GERD Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Yamauchi, Y.; Imanishi, H. [Osaka Soil Test, Osaka (Japan)


    A borehole televiewer (BHTV) logging was conducted to investigate cracks in bored wells. The logging process shoots ultrasonic waves onto bore walls and utilizes reflection waves from the bore walls. If the bores are filled with muddy water, or the ultrasonic waves can pass through even if vinyl chloride tubes have been inserted after excavation, the state of the bore walls can be investigated in principle. Conventional optical scanners are, however, incapable of making this investigation. The BHTV logging can be used for identifying lithofacies from reflection intensities from bore walls (it depends on sound impedance of rocks), not to speak of finding cracks. As a result of making logging upon setting time windows from 105 to 145 {mu} sec in a bored well inserted with a vinyl chloride tube, cracks in the bore wall were identified clearly through the vinyl chloride tube. If the distance between the bore wall and the vinyl chloride tube becomes smaller, setting the time window becomes difficult, making reflection data acquisition more difficult. Impacts of decentering in the vinyl chloride tube on the data and the crack analysis result are small. The reflection intensity has decreased by about half as a result of having the circular vinyl chloride tube inserted. 5 refs., 9 figs., 1 tab.

  2. Development of continuous mixer originated from an idea of udon noodle kneading; Udonneri no haso ni yoru renzokuneri mikisa no kaihatsu

    Maeda, Matabe; Yamada, Ichiu [Maeda Corp., Tokyo (Japan)


    The titled idea was applied to solve a difficult mixing problem of concrete of high fine powder content. In mixing of powdery concrete, and there are disadvantages that long time is required and uniform mixing of water with material is difficult. To solve these disadvantages, a udon noodle kneading system in which an action of folding and extending was repeated to uniformly disperse material was adopted. This is a utilization case of theory of n powers of 2, the material is uniformly dispersed becoming 1,024 layers in 10 times, one million layers in 20 time, 1 billion layers in 30 times. A new model mixer M{center_dot}Y BOX was developed and compared with the conventional system. While an experiment is under way, this mixer seems to be applicable to food industry, pharmaceutical industry, pottery,chemical industry. (NEDO)

  3. Experiment for buried pipes by stepped FM-CW radar; Step shiki FM-CW radar ni yoru maisetsukan tansa jikken

    Suzuki, K.; Ito, M. [Kawasaki Geological Engineering, Co. Ltd., Tokyo (Japan); Tanabe, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)


    The underground radar exploration is adopted to surveys of cavity under the road and buried pipes since the result of high resolution is obtained. However, the explorative depth of the radar is shallow, 2-3m in soil basement, and its applicable field has been limited. The continuous wave radar (FM-CW radar) was devised to get deeper explorative depth, but has been used for the geological structure survey such as the fault survey since it is lower in resolution as compared with the pulse radar. Therefore, to make use of characteristics of the continuous wave radar and enhance resolution in the shallow part, an experiment on buried pipes was conducted for the purpose of assessing and improving the FM-CW radar. In this processing, the wave form treatment used in the reflection method seismic survey was adopted for the radar survey. There are some problems, but it is effective to adopt the same algorithm to that used in the seismic survey to the radar exploration. The explorative depth was discussed from the damping rate of electromagnetic waves and dynamic range of facilities of the experimental site, and 7m was obtained. 5 figs., 1 tab.

  4. Polarimetric borehole radar measurement near Nojima fault and its application to subsurface crack characterization; Polarimetric borehole radar ni yoru Nojima danso shuhen no chika kiretsu keisoku jikken

    Sato, M.; Taniguchi, Y.; Miwa, T.; Niitsuma, H. [Tohoku University, Sendai (Japan); Ikeda, R. [National Research Institute for Disaster Prevention, Tsukuba (Japan); Makino, K. [Geophysical Surveying and Consulting Co. Ltd., Tokyo (Japan)


    Practical application of subsurface crack characterization by the borehole radar measurement to which the radar polarimetric method was introduced was attempted to measuring objects for which the borehole radar has not been much used, for example, the inside of low loss rock mass or fracture zone where cracks tightly exist. A system was trially manufactured which makes the radar polarimetric measurement possible in the borehole at a 1000m depth and with a about 10cm diameter, and a field experiment was conducted for realizing the subsurface crack characterization near the Nojima fault. For the measuring experiment by the polarimetric borehole radar, used were Iwaya borehole and Hirabayashi borehole drilled in the north of Awaji-shima, Hyogo-ken. In a comparison of both polarization systems of Hirabayashi borehole, reflected waves at depths of 1038m and 1047m are relatively stronger in both polarization systems than those with the same polarization form and at different depths, whereas reflected waves around a 1017m depth are strong only as to the parallel polarization system. Characteristics of the polarization in this experiment indirectly reflect crack structures. 6 refs., 6 figs., 1 tab.

  5. Concurrent multidisciplinary mechanical design based on design task analysis and knowledge sharing; Sekkei task bunseki to joho kyoyu ni yoru mechatronics kyocho sekkei

    Kondo, K.; Ozawa, M.; Mori, T. [Toshiba Corp., Tokyo (Japan)


    We have developed a systematic design task planning method based on a design structure matrix(DSM) and a lumped model- based framework for knowledge sharing in a concurrent design environment as key techniques for developing higher quality products in a shorter design time. The DSM facilitates systematic analysis of dependencies among design tasks and optimization of the design process. The framework based on a lumped model description of mechanical systems enables concurrent and cooperative work among multidisciplinary designers at an early stage of the design process. In this paper, we also discuss the relationships between these techniques and the product development flow from product definition to detailed design. (author)

  6. Improvement of diesel engine performance by hydraulically powered electronic control (mechatronics) system. Hakuyo diesel kikan no mechatronics system ni yoru seino kojo

    Sonoda, K.; Nakamura, Y.; Kajima, T.; Sato, S.; Fujii, T.; Tobe, Y. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))


    This paper describes new hydraulically-actuated mechanisms for both fuel injection and inlet/exhaust valve operation of diesel engines through solenoid valves, which obviate the conventional cam-driven system. These mechanisms were integrated with an electronic control unit also developed in this study and they were mounted as a mechatronics system'' on a power-increased single-cylinder engine. This mechatronics system was mainly composed of an injection control. boost and accumulation component, an inlet and exhaust valve control component, a solenoid valve, an electronic control equipment, a hydraulic power unit, and a maneuvering unit. The verification test was carried out for the improvement of diesel engine performance by the hydraulically powered mechatronics system. As a result, it was proved not only that these mechanisms provide stable operating characteristics over a wide range of conditions, but also that the electronic control system allows accurate, smooth response. 3 refs., 23 figs., 2 tabs.

  7. Solution of combinatorial optimization problems by an accelerated hopfield neural network. Kobai kasokugata poppu firudo nyuraru netto ni yoru kumiawase saitekika mondai no kaiho

    Ohori, T.; Yamamoto, H.; Setsu, Nenso; Watanabe, K. (Hokkaido Inst. of Technology, Hokkaido (Japan))


    The accelerated approximate solution of combinatorial optimization problems by symmetry integrating hopfield neural network (NN) has been applied to many combinatorial problems such as the traveling salesman problem, the network planning problem, etc. However, the hopfield NN converges to local minimum solutions very slowly. In this paper, a general inclination model composed by introducing an accelerated parameter to the hopfield model is proposed, and it has been shown that the acceleration parameter can make the model converge to the local minima more quickly. Moreover, simulation experiments for random quadratic combinatorial problems with two and twenty-five variables were carried out. The results show that the acceleration of convergence makes the attraction region of the local minimum change and the accuracy of solution worse. If an initial point is selected around the center of unit hyper cube, solutions with high accuracy not affected by the acceleration parameter can be obtained. 9 refs., 8 figs., 3 tabs.

  8. Method for the traveling salesman problem by controlling two parameters of the Hopfield neural network; Parameter seigyogata hop field net ni yoru junkai salesman mondai no kaiho

    Setsu, N.; Murakami, K.; Ohori, T.; Watanabe, K. [Hokkaido Institute of Technology, Sapporo (Japan)


    For solving the traveling salesman problem (TSP) by using a continuous value outputting neural net (NN), an investigation was given on the accuracy of solution and the possibility on traveling routes by using the penalty coefficient and temperature as the parameters for energy functions. The parameter range to obtain high-quality traveling routes was shown by a numerical experiment. The experimental result revealed that, when the penalty coefficient `r` is large, the traveling route possibility tends to become higher, but the route length increases, and when the `r` is small, the traveling route possibility becomes lower, but the route length decreases, also in the continuous value outputting NN as in the two-value outputting NN. Noticing this fact, and in order to improve the traveling route possibility as well as the solution quality, a method was proposed to expand the penalty control method which was proposed previously by the authors on the two-value outputting NN, into the continuous value outputting NN. In addition, a proposal was also made on a method to derive an optimal temperature efficiently by using the golden section method. It was found that the relative error has been reduced by 48% on the average as compared with that in the conventional method in which the temperature is fixed. 6 refs., 5 figs.

  9. Changes of inflammatory cells in rat lungs exposed to diesel emissions; Diesel haiki bakuro ni yoru rat hai no ensho saibo no henka

    Kato, A. [Japan Automobile Research Institute Inc., Tsukuba (Japan); Kagawa, J. [Tokyo Women`s Medical College, Tokyo (Japan)


    Study was made on the effect of exposure to diesel emissions on inflammatory cells in a rat lungs. Four kinds of exposure gases with different contents of NO2 and particulate were prepared by diluting diesel emissions. Rats were exposed to diluted diesel emissions for 24 months, and inflammatory cells were detected morphologically in light microscopic and TEM specimens. As a result, particle-laden- alveolar macrophages increased dose- and time-dependently into the submucosa of intrapulmonary bronchioles, alveolar spaces and interstitume of alveolar walls, and bronchoassociated lymphatic tissues. Mast cells infiltrated into the interspaces of epithelial cells in airways. In the submucosa of the terminal bronchioles and the interstitume of alveolar walls, some sorts of inflammatory cells such as mast cells, plasma cells, neutrophils and lymphocytes infiltrated, and some cells showed cell-to-cell contacts. However, the airways were rarely injured by infiltration of inflammatory cells except for a fibrotic change. 2 refs., 2 figs., 2 tabs.

  10. Numerical prediction with `DMDF` model of pack ice motion in the Okhotsk sea; DMDF model ni yoru Okhotsk kai ryuhyo undo no suchi yosoku

    Matsuzawa, T.; Yamaguchi, H.; Suzuki, S.; Kato, H. [The University of Tokyo (Japan); Rheem, C. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science


    A simulation was performed on pack ice motion in the Okhotsk Sea in winter by using the distributed mass/discrete floe (DMDF) method that carries out a dynamic numerical calculation of pack ice motion. Several kinds of cases were compared and calculated. As a result, effectiveness was verified on a DMDF model with boundary conditions which are relatively large in range and complex in nature. At the same time, it was possible to estimate part of the characteristics of pack ice motion in this sea area. The numerical calculation used the floe distribution on February 1, 1994 as the initial condition, and performed calculations on conditions until February 8 giving considerations on meteorological and hydrographic data. As a result, the calculation result showed the same movements as those in the observed ice conditions. If an ocean current is hypothesized steady, the calculation is affected more than necessarily by the ocean current, and it derives a result departed from reality. From these findings, it was elucidated that floe motions are governed mainly by wind; and in making a numerical modeling, a consideration including composition with the ocean current is necessary. Shear stress of wind has its acting direction displaced from the wind direction because of effect of the Corioli`s force. 6 refs., 13 figs., 2 tabs.

  11. Simulation of tandem hydrofoils by finite volume method with moving grid system; Henkei koshi wo tsukatta yugen taisekiho ni yoru tandem suichuyoku no simulation

    Kawashima, H. [Ship Research Inst., Tokyo (Japan); Miyata, H. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering


    With an objective to clarify possibility of application of time-advancing calculated fluid dynamic (CFD) simulation by using a finite volume method with moving grid system, a simulation was performed on motion of a ship with hydrofoils including the control system therein. The simulation consists of a method that couples a moving grid system technology, an equation of motion, and the control system. Complex interactions between wings and with free surface may be considered automatically by directly deriving fluid force from a flow field by using the CFD. In addition, two-dimensional flows around tandem hydrofoils were calculated to solve the motion problem within a vertical plane. As a result, the following results were obtained: a finite volume method using a dynamic moving grid system method was applied to problems in non-steady tandem hydrofoils to show its usefulness; a method that couples the CFD with the equation of motion was applied to the control problems in the tandem hydrofoils to show possibility of a new technology for simulating motions; and a simulation that considers such wing interference as wave creation, discharged vortices, and associated flows was shown useful to understand characteristics of the tandem hydrofoils. 13 refs., 14 figs.

  12. Numerical simulation for submerged body fitted with hydrofoil by boundary element method; Kyokai yosoho ni yoru yokutsuki bossuitai mawari no nagare keisan

    Masuda, S.; Kasahara, Y.; Ashidate, I. [NKK Corp., Tokyo (Japan)


    In a high-speed boat of a type using hydrofoils, lifting force increases in proportion to square of its length, while displacement is proportional to the third power. Therefore, an idea has come up that speed of a large boat may be increased by combining the hydrofoils with a submerged body. In other words, the idea is to levitate a ship by using composite support consisting of buoyancy of the submerged body and lifting force caused by the hydrofoils. Insufficiency of the lifting force may be complemented by the buoyancy of the submerged body which increases in an equivalent rate as that in the displacement. However, combining a submerged body with hydrofoils render a problem that lifting force for hydrofoils decreases because of interactions among the submerged body, hydrofoils, and free surface. Therefore, assuming a model of a submerged body with a length of 85 m cruising at 40 kt, analysis was given on decrease in lifting force for hydrofoils due to interactions between the submerged and lifting body and free surface by using the boundary element method. As a result, it was verified that the lifting force for the hydrofoils decreases as a result of creation of a flow that decreases effective angle of attach of the hydrofoils. It was also made clear that making the submerging depth greater reduces the decrease in the lifting force. 9 refs., 14 figs., 1 tab.

  13. Evaluation of building envelopes from the viewpoint of capability of controlling thermal environment; Onnetsu kankyo chosei noryoku ni yoru kenchiku gaihi no hyoka no kokoromi

    Umeda, K; Ono, S [Taisei Corp., Tokyo (Japan); Shukuya, M [Musashi Institute of Technology, Tokyo (Japan)


    The ability that architectural space improves the thermal environment in comparison with outdoor environment is called the `capability of controlling thermal environment.` As the value becomes higher, the indoor thermal environment is more improved. In this paper, the controlling capability of six building envelopes with different window systems was compared. The heat transfer in the wall and window system is approximated using a lumped mass model of heat capacity to obtain a heat balance equation and combined with the heat balance equation in indoor air for backward difference. The wall surface temperature and indoor air temperature in a calculation model are then calculated. A radiation absorption coefficient is used for mutual radiation on each wall. In the model, the adjoining room or first- and second-floor rooms were made the same in conditions as the model on the assumption that the one-side lighted office in an RC reference floor is in the non-illumination and non-airconditioning state. In summer, the controlling capability remarkably varies depending on the window system. For the window facing the south, the annual capability is more advanced than in other directions and the indoor thermal environment is improved on the average. 7 refs., 12 figs., 1 tab.

  14. Clearness index in cloudy days estimated with meteorological information by multiple regression analysis; Kisho joho wo riyoshita kaiki bunseki ni yoru dontenbi no seiten shisu no suitei

    Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan). Faculty of Engineering


    Study is under way for a more accurate solar radiation quantity prediction for the enhancement of solar energy utilization efficiency. Utilizing the technique of roughly estimating the day`s clearness index from forecast weather, the forecast weather (constituted of weather conditions such as `clear,` `cloudy,` etc., and adverbs or adjectives such as `afterward,` `temporary,` and `intermittent`) has been quantified relative to the clearness index. This index is named the `weather index` for the purpose of this article. The error high in rate in the weather index relates to cloudy days, which means a weather index falling in 0.2-0.5. It has also been found that there is a high correlation between the clearness index and the north-south wind direction component. A multiple regression analysis has been carried out, under the circumstances, for the estimation of clearness index from the maximum temperature and the north-south wind direction component. As compared with estimation of the clearness index on the basis only of the weather index, estimation using the weather index and maximum temperature achieves a 3% improvement throughout the year. It has also been learned that estimation by use of the weather index and north-south wind direction component enables a 2% improvement for summer and a 5% or higher improvement for winter. 2 refs., 6 figs., 4 tabs.

  15. Characteristics on the heat storage and recovery by the underground spiral heat exchange pipe; Chichu maisetsu spiral kan ni yoru chikunetsu shunetsu tokusei

    Imai, I [Kure National College of Technology, Hiroshima (Japan); Taga, M [Kinki University, Osaka (Japan)


    The consistency between the experimental value of a soil temperature and the calculation value of a soil temperature given by a non-steady heat conduction equation was confirmed. The experimental value is obtained by laying a spiral heat exchange pipe in the heat-insulated soil box and circulating hot water forcibly in the pipe. The temperature conductivity in soil significantly influences the heat transfer in soil. The storage performance is improved when the temperature conductivity increases because of the contained moisture. As the difference between the initial soil temperature and circulating water temperature becomes greater, the heat storage and recovery values increase. A thermal core heat transfer is done in the spiral pipe. Therefore, the diameter of the pipe little influences the heat storage performance, and the pitch influences largely. About 50 hours after heat is stored, the storage performance is almost the same as for a straight pipe that uses the spiral diameter as a pipe diameter. To obtain the same heat storage value, the spiral pipe is made of fewer materials than the straight pipe and low in price. The spiral pipe is more advantageous than the straight pipe in the necessary motive power and supply heat of a pump. 1 ref., 11 figs., 1 tab.

  16. Dynamics of hydrogen induced blistering of a low carbon steel sheet by lamb waves analysis; Ramuha no teiryo kaiseki ni yoru hakubanteitansoko no suiso hare no dainamikkusu

    Sato, Teruyoshi.; Takemoto, Mikio. [Aoyama Gakuin University, Tokyo (Japan). Faculty of Science and Engineering


    With the aim of studying the fracture dynamics of environmentally assisted fractures in thin plates, we developed a new source simulation method of the zeroth-order symmetric (or S{sub 0}-) Lamb wave using the experimental overall-transfer function of the system. The transfer function was determined by the time-domain deconvolution of detected S{sub 0}-Lamb component by the artificial fracture source of a compression -type PZT element whose vibration kinetics was estimated by the iteration so that the S{sub o}-waveform detected. Hydrogen induced blistering was found to be caused by the succession of fast Mode-I fracture with source rise times from 0.6 to 1.0{mu}s. The crack volume estimated by the source simulation corresponded to that of fine blistering with an opening displacement of 5{mu}m. As the estimated fracture kinetics of hydrogen blistering coincide with those of delayed fracture of high tension low alloy steel under tensile loading, the kinetics of first and micro-fractures and blistering induced by hydrogen gas precipitation appears to be independent on the hydrogen solubility and strength of steels, the applied stresses and the orientation of cracks. (author)

  17. Review of research on remote sensing with digital map. Remote sensing to suchi chizu no ketsugo ni yoru kenkyu no shokai

    Tanaka, S; Sugimura, T [Remote Sensing Technology Center of Japan, Tokyo (Japan)


    This paper describes the relationship between remote sensing and digital map. The relation between remote sensing and digital map is roughly classified into two kinds. One of them is utilization of remote sensing and digital map in combination to analyze phenomena, and the other is normalization of remote sensing data by use of digital map. For examples of utilizing remote sensing and digital map, there are the creation of a perspective image of ground scene from Landsat MSS data by use of a mesh type digital map of the orthogonal co-ordinates, and the creation of an image of the enviromental research along roads from satilite data by use of a vector type digital map. Furthermore, this paper introduces a procedure of correcting geographical strains by use of a digital map and converting a radar image to corrected plane image, and the use of a digital map in the global scale for the analysis of floods and other purposes. 20 refs., 5 figs., 1 tab.

  18. Studies on utilization of nitrogen-fixing bacteria for saving energy; Chisso koteikin no katsuyo ni yoru sho energy no kenkyu

    Uozumi, T; Koyama, R; Horiuchi, M; Hidaka, M; Masaki, H [The University of Tokyo, Tokyo (Japan); Shigematsu, T; Inoue, A [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)


    This paper describes analysis and enhancement of nitrogen-fixing gene of rice root bacteria, such as Klebsiella oxytoca, Azospirillum lipoferumn and Sphingomonas paucimobilis, for realizing energy saving through conservation of nitrogenous fertilizers. For K. oxytoca, modified strain R-16 was developed, which can fix nitrogen effectively even in the presence of NH4{sup +}. Nitrogen-fixing ability of A. lipoferumn depends on the activity control by the modification of nitrogen-fixing enzyme as well as on the adjustment of transcription level by the transcription activating gene, nifA. The control gene relating to the above was analyzed by making clones. As a result, a modified strain TAl without the control by NH4{sup +} was developed. The R-16 and TAl strains were inoculated into rice sterile-cultured without nitrogen. Consequently, inoculated strains were settled in the root, which resulted in the increased vegetation weight of plant to two times heavier than that without inoculation. 9 refs.

  19. Synthesis of AlN fine particles by surface corona discharge-CVD; Enmen corona hoden CVD ni yoru AlN biryushi no gosei

    Oyama, Y.; Chiba, S. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Harima, K> ; Kondo, K.; Shinohara, K. [Hokkaido University, Sapporo (Japan)


    With an objective to improve insulating and heat dissipating substrates substituting for the conventional alumina substrates, discussions been given on synthesis of AlN fine particles by means of gaseous phase reaction between AlCl3 and NH3 using surface corona discharge as a reaction exciting source. AIN particles should be highly pure to acquire high-heat conductivity, and fine and uniform particles to obtain dense sinters at low temperatures. The particles obtained by using the present method were amorphous particles having nearly spherical form and smooth surface. The particle diameter depends on the initial concentration of AlCl3, and is proportional to 0.4 square of the concentration. Within the range in the present experiment, the diameters ranged from 208 nm to 431 nm. The particle diameter increased in proportion to 0.2 square of an average gas stagnating time within the plasma generating region. The particle size distribution consisted of highly uniform fine particles having the standard deviation at about the same degree as that in the conventional thermal CVD process. The alumina-based oxygen was removed completely by reduction due to graphite powder, but the re-oxidation during removal of the remaining graphite using combustion had oxygen remained at 7.4% by weight. 16 refs., 7 figs.

  20. Studies on sleep patterns and fatigue due to shift work and their work adaptability. Kotai sagyo ni yoru suimin dotai to hiro oyobi sono sagyo tekiosei no kenkyu

    Matsuoka, N.; Yokota, A. (Univ. of Occupational and Environmental Health, Kitakyushu (Japan). School of Medicine)


    Studies were made on sleep patterns and fatigue due to shift work and their work adaptability with respect to the following items: (1) With a nurse work system as the object, a survey of rectum temperature, heart rate and rhythm before and after a midnight shift, and sleep at rising in the morning using the OSA survey method; (2) To analyze actual conditions of cumulative fatigue felt by shift workers and fatigue factors, a survey on shift work history, overtime work time, work patterns, symptoms of cumulative fatigue, and and life satisfaction; (3) A survey on daytime sleep record maintained at working places of guards including those of middle or advanced age, and sleep as affected by a nap; (4) A method of improving complains of circadian rhythm disorders because of variations in sleep and emergence rhythms experienced by shift workers, and discussions of usability of light radiation; and (5) Establishment of a technique to indicate effects of psychological burdens and psychogenic stress on visual functions of shift workers using tensions in focal adjustment. 5 figs., 5 tabs.

  1. Optimization of the catalytic converter internal flow by using 3D-CFD; Sanjigen nagare kaiseki ni yoru shokubai converter nai nagare no saitekika

    Toi, M; Sugiura, S [Toyota Motor Corp., Tokyo (Japan)


    By using computational fluid dynamics and statistical quality control method, we investigated the contribution of front and rear catalytic converter cone shape for the pressure loss and the partial flow, also led the optimal terms and the predictional formulations efficiently. According to this, we can investigate the optimal position of the catalytic converter from the planning. 8 figs., 6 tabs.

  2. Study of heart rate variability in driving situation by fractal analysis; Fractal kaiseki ni yoru untenchu no shinpaku hendo no bunseki

    Hirata, Y; Nagaoka, M [Mazda Motor Corp., Hiroshima (Japan)


    This paper will explain method of fractal analysis for heart rate variability, as measuring method of mental stress in vehicle driving. In the previous, although there was a measuring method of mental stress by RSA, a issue arise such as reliability of analysis, because driver`s heart rate affect by respiration and muscle motion as well. We have established a method to measure mental stress by fractal dimension. And tried it is the proving ground and public road driving. We have confident that it is more reliable than RSA to quantify driver`s mental stress and fatigue. 9 refs., 9 figs., 1 tab.

  3. Detachment of solid particulate soils by centrifugal force part 3; Properties of direction for removal force. Enshinryoku ni yoru ryushi yogore no jokyo. dai sanpo; Jokyoryoku no hokosei

    Iwasaki, Y. (Koriyama Womens College, Fukushima (Japan)); Lee, S.H. (Tokyo Gakugei Univ., Tokyo (Japan)); Yabe, A. (Bunka Womens Univ., Tokyo (Japan))


    Removal by centrigugal force of polystyrene-latex particles with particle sizes of 5, 10 and 15 {mu} m adhering to a glass substrate is studied. Washing was carried out by using an ultracentrifuge provided with an angular rotor, with a rotor angle {theta} of 0 {approximately} 60 {degree}, varying the ratio of horizontal component Fh to vertical component Fv from 1:0 to 1:1.73. Washing was further carried out, changing an angle {theta}{prime} of centrifugal force to the surface on which the particles adhered. From this experiment, the following conclusions were obtained. The less the contribution of Fv to the constant Fh, or reversely the greater the contribution of Fh to the constant Fv, the more was the extent of removal. When the surface on which the particles adhered was turned to the direction pressed by centrifugal force, Fv acted negatively for removal of particles and exhibited a different tendency from that when turned to the the centrifugal direction. When {theta}{prime} was 180 {degree}, the removal force giving an extent of removal of about 80% was 1.5 {times} 10 {sup {minus} 9} N for 5 and 10 {mu} m particles, and 25 {times} 10 {sup {minus} 9} N for 15 {mu} m particles. 11 refs., 14 figs., 3 tabs.

  4. Near-field ground-motion intensity related to displacement of objects; Chokka jishin ni yoru buttai no ido to jishindo tsuyosa

    Omachi, T. [Tokyo Institute of Technology, Tokyo (Japan)


    Examples of object displacement due to the earthquake in Japan were reversely analyzed. The example of stone jumping in 1984 was studied. Because of soft ground, the characteristic period can be detected by composing a spring system of stone (as a mass) against the ground. As the phenomenon is considered as seismic response, the following facts were known through vibrational test and numerical analysis simulation: the stone jumping is a non-linear response, and depends upon the period and amplitude of input. Its distance is influenced by the horizontal movement. To make the stone jump, the component of which the period is 0.3 to 1.0 sec is dominant with the necessary acceleration of 1.5g. A bell tower weighing 5t in total was displaced 1m by the earthquake in 1909. A model test was conducted by measuring the characteristic period of ground and bell tower. It was known that not the vibration in the direction of beams, but the stronger vibration than 0.1g in the diagonal direction made the pillars jump. The earthquake in 1930 made an exhibited torpedo slide and leave its frictional marks. Through the simulation conducted, it was presumed that the first and succeeding frictional marks were marked by the P-wave and S-wave, respectively, and that the seismic duration was almost 10 sec with the acceleration of 1.3 to 2g. 11 refs., 10 figs., 1 tab.

  5. Method of measurement of near tip field of fast propagating cracks by means of interferometry; Hikari kansho ni yoru kosoku shinten kiretsu sentanbu no oryokuba keisokuho

    Suzuki, s.; Miyazaki, F. [Toyohashi University of Technology, Aichi (Japan); Nakane, K. [Nitto Denko Corp., Osaka (Japan)


    The measurement by an interference method at the tip of fast propagating cracks was investigated. To clarify the direction-dependent problem of dynamic cracks in a higher-order term, a high-precision stress field must be measured in every direction. In this method, the propagated interference fringes near the crack tip are shot at a speed of some hundreds of m/sec, and the coefficient of dynamic stress extension is obtained from the expression given when the number of fringes (`m`) in the interferences fringes is differentiated partially. The information below was obtained. The stress field in every direction can be analyzed by the interference method. However, the interference fringes in an area of absolute {theta} < 120{degree} are radially spread from the crack tip, so the precision of the interference fringes in the {gamma} direction deteriorates. In this area, the above partial differential is higher in precision when {alpha}m/{alpha}{theta} is used instead of {alpha}m/{alpha}{gamma}. The stress extension coefficient obtained by a caustic method can be verified if a stress field of {theta} = {plus_minus}72{degree} is analyzed by the interference method. By shooting in this optical system, the COD measurement, the K-value measurement of caustic light, and the stress field measurement by an interference method can be done simultaneously. 17 refs., 11 figs.

  6. Change of wettability of PTFE surface by sputter etching and excimer laser. Sputter etching oyobi excimer laser ni yoru PTFE hyomen no shinsuika

    Yamamoto, S. (Nitto Denko Corp., Osaka (Japan)); Kubo, U. (Kinki University, Osaka (Japan))


    The wettability of PTFE (polytetrafluoroethylene) surfaces was improved by sputter etching and excimer laser irradiation. In sputter etching, the PTFE surface was treated by reactive sputter etching with H2O gas to give active groups on the surface. In laser irradiation, the surface was irradiated in pure water by high-energy KrF excimer laser. As the surface wettability was evaluated with a contact angle to water, the contact angle decreased remarkably in both treatments resulting in a good improvement effect. In sputter etching, various new chemical bonds such as F-C=O, F2C-FC-O, F2C-C-O and C-O were observed because of a decrease in F and incorporation of oxygen. Such chemical bonds could be eliminated by ultraviolet ray irradiation, and the treated surface condition approached the initial condition after irradiation of 200 hours. In laser irradiation, it was suggested that C-F bonds were broken, and OH groups were added to the surface by dissociation of H2O to H and OH. 7 refs., 8 figs., 1 tab.

  7. Increase in information by improvement of measuring method in a multichannel taste sensor; Multichannel aji sensor no sokutei hoho no kairyo ni yoru johoryo no zoka

    Ikezaki, H.; Taniguchi, A. [Anritsu Corp., Tokyo (Japan)


    We have developed a multichannel taste sensor with lipid membranes which can detect and quantify the basic taste substances in aqueous solution. The aim of the present study is to increase selectivity to adsorptive taste substances (bitter, umami and astringent taste substances) for quantification of taste by improving measuring methods. High selectivity to adsorptive taste substances is obtained by CPA measurement algorithm (CPA: Change of membrane Potential caused by Adsorption). High repeatability is also obtained by developing a cleaning technique of taste sensor. 18 refs., 8 figs., 5 tabs.

  8. Analysis of taste qualities and ingredients of beer by taste sensing system; Mikaku sensor ni yoru beer no ajishitsu to seibun no bunseki

    Ezaki, S.; Yuki, T. [Kinki University, Osaka (Japan); Toko, K. [Kyushu University, Fukuoka (Japan); Tsuda, Y.; Nakatani, K. [Suntory Ltd., Osaka (Japan)


    The taste of beer was measured using a taste sensing system with eight kinds of lipid membrane. The output from the sensor has high discriminating power and high correlation with taste substances in beer and sensory test by human. The estimation of the concentration of taste substances by multiple regression analysis was fairly well. The taste sensor also well estimated the result of sensory test of many keywords concerning beer taste. 16 refs., 8 figs., 1 tab.

  9. Deflection control system for prestressed concrete bridges by CCD camera. CCD camera ni yoru prestressed concrete kyo no tawami kanri system

    Noda, Y.; Nakayama, Y.; Arai, T. (Kawada Construction Co. Ltd., Tokyo (Japan))


    For the long-span prestressed concrete bridge (continuous box girder and cable stayed bridge), the design and construction control becomes increasingly complicated as construction proceeds because of its cyclic works. This paper describes the method and operation of an automatic levelling module using CCD camera and the experimental results by this system. For this automatic levelling system, the altitude can be automatically measured by measuring the center location of gravity of the target on the bridge surface using CCD camera. The present deflection control system developed compares the measured value by the automatic levelling system with the design value obtained by the design calculation system, and manages them. From the real-time continuous measurement for the long term, in which the CCD camera was set on the bridge surface, it was found that the stable measurement accuracy can be obtained. Successful application of this system demonstrates that the system is an effective and efficient construction aid. 11 refs., 19 figs., 1 tab.

  10. Vertical gust response prediction of cable-stayed bridges in yawed wind; Shachokyo no shafu ni yoru enchoku gust oto no yosoku

    Nakamura, S.; Nagamachi, K.; Kawai, Y. [Kawasaki Steel Corp., Tokyo (Japan); Kimura, K.; Fujino, Y. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Tanaka, H.


    This paper outlines the vertical gust response analysis method in a yawed wind, gives an analytic example, and compares the experimental result with the analytic result to investigate the application of an analysis method and the validity of assumption and approximation. The vertical gust response to two cable-stayed bridges under construction in a yawed wind was predicted by applying assumption and approximation to the gust response prediction method in a yawed wind with the cantilever model having a plate cross-section manipulated. In this case, the wind velocity component perpendicular to the leading edge was defined as an effective wind velocity, and a bridge axis and the component perpendicular to a bridge axis were separately calculated in response. Moreover, some aerodynamic coefficients of a bridge girder cross-section were approximately obtained from the characteristics of the flat blades with same aspect ratio. The obtained analytic result was compared with the wind tunnel test result based on all bridge models. The result showed that the former almost coincides with the latter, the assumption and approximation of this time are verified in validity, and this analysis method can be used for cable-stayed bridges under construction. 10 refs., 7 figs., 2 tabs.

  11. Field vibration test of a long-span cable-stayed bridge by large exciters. Daishinpuku kashin ni yoru chodai shachokyo no jikkyo shindo jikken

    Okauchi, I. (Chuo University, Tokyo (Japan). Faculty of Science and Engineering); Miyata, T. (Yokohama National University, Yokohama (Japan). Faculty of Engineering); Sasaki, N. (Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)); Tatsumi, M.


    Long-span cable-stayed bridge requires indispensably discussions on safety against gale and earthquake, and correct assessment on its inherent vibration characteristics at the design stage is critical. However, theoretical assessment on structural decay is difficult, hence it is desirable to make measurement and verification upon its completion. This paper reports the result of measurements and considerations on a three-span continuous steel cable-stayed bridge with a length of 790 m (185 m + 420 m + 185 m) spanning between Hitsuishi Island and Iwakuro Island in the Kojima-Sakaide route of the Honshu-Shikoku connecting bridge. Large shaking machines were used to give girders vibrations with large amplitudes (10 cm at maximum), and high-accuracy measurements were made. The measurements verified the reasonability of the dynamic design for the bridge. The measured value of the logarithmic decay rate [delta] as the major experimental data presented that bending vibration is large as a whole, with torsional vibration somewhat smaller, and all the design values were on safety side. Confirmation was made on amplitude dependence of the decay rate, the inherent modes of low-order vibrations, and coupled behaviors among the girders, cables, and towers. 16 refs., 13 figs., 3 tabs.

  12. Vertical vibration control system for PC cable-stayed bridge during cantilever construction; Shuketa jogedo seishin sochi ni yoru haridashi sekoji no PC shachokyo no seishin

    Oshio, M.; Nakano, R.; Niihara, Y.; Yano, K.; Takeda, T. [Kajima Corp., Tokyo (Japan)


    A PC cable-stayed bridge under extension construction having long span length may have long-cycle vibration generated because of wind. The vibration puts workers working on main girders into a state of seasick causing the workability to drop. Therefore, with an objective to reduce vibration occurring on the main girders during construction, discussions were given on application of an active type vertical vibration absorbing device. The vibration absorbing device is an active system that a weight is driven vertically by a hydraulic actuator. The device was developed with a target that damping ratio when a maximum extension is 120 m becomes three times that when no vibration is absorbed for a 5-span continuous PC cable-stayed bridge with a length of 675 m, a central span of 260 m, and a width of 11 m. A cage housing the weight is connected with the actuator at its top by using pins, and the weight is supported being suspended from the top of the actuator. Vibration is absorbed by utilizing reactive force generated when the weight is driven vertically by the hydraulic actuator. The hydraulic actuator contains a gas spring that supports the dead weight of the weight. Experiments have verified the effectiveness of the vertical vibration absorbing device. 4 refs., 12 figs., 3 tabs.

  13. Reduction of seismic response long-span PC cable-stayed bridge by passive dampers; Damper ni yoru saidai PC shachokyo no jishinji oto no teigen

    Takeda, T.; Yamanobe, S.; Niihara, Y. [Kajima Corp., Tokyo (Japan)


    It is important in designing a PC cable-stayed bridge to properly estimate the seismic response of the bridge for reduction of the response. In this paper, an improvement of the seismic resistance of PC cable-stayed bridges when dampers are installed between the deck and piers and lateral vibration of the deck is restricted is investigated using a time history response model. PC cable-stayed bridges with a span length of 400 m, particularly two types of bridges of harp and semi-harp are investigated and the following is found by analyzing the case where there are installed hysteresis type dampers (with 1 cm yield displacement and secondary rigidity assumed to be 1/10 times that of initial rigidity, the initial rigidity being parametrically changed.) or viscous type dampers (a damping factor is changed.) The result shows that the dampers can reduce the seismic response of a PC cable-stayed bridge and that a semi-harp configuration of stay cables where stay cable members are substantially vertically arranged is more effective than a harp configuration for the seismic performance of PC cable-stayed bridges. The damper partly bear inertial force of the bridge upon earthquake whereby tension of the stay cable members is reduced and bending moment of the deck is reduced. There is existing an optimum characteristic value of the damper concerning the bending moment of the piers. 5 refs., 7 figs., 2 tabs.

  14. Wind-induced cable vibrations and countermeasures of cables of PC cable-stayed bridge. PC syachokyo keburu no kaze ni yoru shindo to sono taisaku

    Yoneda, M. (Kawada Industries Inc., Tokyo (Japan))


    In recent years, long span of cable-stayed bridges is remarkable. The wind-induced cable vibration called as line vibration and wake galloping was given as an important problem not only in the steel cable-stayed bridges but also in the PC cable-stayed bridges. The technical engineers in design of the cable-stayed bridges have many times to confront the problems on the vibration control of cables, it is considered that sufficient understand of the wind-induced vibration and countermeasures for cables of the PC cable-stayed bridges is necessary. Many reports on the countermeasure examples and trend of vibration control centred on cables of the cable-stayed bridges have been published. In this paper, the wind-induced vibration of cables in the cable-stayed bridges was reviewed, the examples of countermeasures of vibration control on cables in the PC cable-stayed bridges was mainly introduced. The remaining tasks and future prospects on vibration control of the PC cable-stayed bridges were described. 14 refs., 13 figs., 4 tabs.

  15. Identification of dynamic characteristics by field vibration test in Tsurumi Tsubasa bridge; Tsurumi Tsubasakyo no shindo jikken ni yoru doteki tokusei no dotei

    Yamaguchi, H. [Saitama University, Saitama (Japan). Faculty of Engineering; Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Expressway Public Corp., Tokyo (Japan); Kato, M.; Okada, J. [NKK Corp., Tokyo (Japan)


    Field vibration test of the Tsurumi Tsubasa Bridge, a long span cable stayed bridge, has been conducted. Focusing on its dynamic characteristics, an identification method from test results and its validity were investigated. The natural frequency identified using mode circle and resonance curve from steady vibration test agreed with that identified by the peak method from free damping test. Accordingly, there was no difference due to identification methods, and both methods provided appropriate accuracy. The natural vibration mode obtained from the steady vibration test agreed with that obtained by the eigenvalue analysis. The dispersion of experimental values, which indicates the adaptation to mode circle method, became a scale indicating reliability of identified values. When the damping obtained by the half power method for the microtremors test is compared with that identified from the steady vibration test and free damping test, it is required to compare them at lower amplitude level region, considering that the amplitude level of microtremors test is very low. For the dynamic characteristics of the Tsurumi Tsubasa Bridge, it was found that it has lower natural frequency and higher modal damping compared with other cable stayed bridges with similar scale of span. 18 refs., 13 figs., 4 tabs.

  16. Prevention of the growth of algae and protests in water treated with a calcinated sand; Ceramics seihin ni yoru suisochu no soruinado no hassei boshi

    Watanabe, K.; Kakita, Y. [Fukuoka University, Fukuoka (Japan). Faculty of Pharmaceutical Science; Tanaka, A.; Yamasaki, K.; Masamoto, H.; Nakahara, S. [Fukuoka University, Fukuoka (Japan). Faculty of Engineering; Egashira, K. [Kyudenko Corp., Fukuoka (Japan)


    A commercial calcinated sand, Cleansand-205 (abbr. Kls-205 : a silica sand coated by a special procedure with a mixture of the oxides of Si, Al, Ti, and Ag), was tested for its ability to inhibit the growth of algae in a laboratory (batch-system) experiment. The growth of algae in water taken from a domestic gold fish basin was inhibited almost completely by about 5% (w/v) of Kls-205, under the conditions where fairly amounts of both nitrogen and phosphorus were present. However, Kls-205 (5%) showed little inhibition on algae which had already abundantly grown, and did not suppress further growth. The abilities of Kls-205 to adsorb nitrogen, phosphorus and carbon dioxide required for the growth and photosynthesis of algae were weak. The amounts of beta- and gamma-radiation and harmful heavy metal ions were the same levels as those from non-treated natural water. The dissolution of any antialgal substances and the generation of active oxygens were not observed. The possible role of Ag and/or its oxide with oligodynamie in inhibiting the growth of algae by Kls-205 was discussed. 15 refs., 4 figs., 2 tabs.

  17. Geochemical fixation of carbon dioxide in the environment. Chikyu kagakuteki kenchi kara no tansan'en ni yoru nisanka tanso no kotei

    Ishikawa, M [Mitsubishi Research Institute, Inc., Tokyo (Japan)


    The Mitsubishi Research Institute has investigated and discussed the current situation and the future direction of the studies on geochemical fixation of carbon dioxide by means of carbonates. This paper summarizes the results thereof. The discussion items are listed as follows: The current status of land areas active in carbonate fixation (lake-bottom deposits, sabkha, dry areas, carbonate rock areas); investigation on sea areas active in carbonate fixation (coral reef areas, land shelf areas, open sea areas, and mantle); development of environmental change analyzing technologies (measurement of ancient environments, measurement of fixation ages, development of local area analysis, measurement of diagenetic structures, origin and behavior of trace elements in carbonate substances, and measurement of the current environments); evaluation on fixation ability of carbon sinks (circulation and fixation in coral reef ecosystems, calcification mechanisms in calcareous algae, dissolution processes at ocean bottoms, and inorganic chemical measurement); and investigation on simulation models (solution chemistry equilibrium model and global carbonate circulation model). 4 refs., 1 tab.

  18. OpenNI cookbook

    Falahati, Soroush


    This is a Cookbook with plenty of practical recipes enriched with explained code and relevant screenshots to ease your learning curve. If you are a beginner or a professional in NIUI and want to write serious applications or games, then this book is for you. Even OpenNI 1 and OpenNI 1.x programmers who want to move to new versions of OpenNI can use this book as a starting point. This book uses C++ as the primary language but there are some examples in C# and Java too, so you need to have about a basic working knowledge of C or C++ for most cases.

  19. Gd-Ni-Si system

    Bodak, O.I.; Shvets, A.F.


    By X-ray phase analysis method isothermal cross section of phase diagram of the Gd-Ni-Si system at 870 K is studied. The existence of nine previously known compounds (GdNisub(6.72)Sisub(6.28), GdNi 10 Si 2 , GdNi 5 Si 3 , GdNi 4 Si, GdNi 2 Si 2 , GdNiSi 3 , GdNiSi 2 , Gd 3 Ni 6 Si 2 and GdNiSi) is confirmed and three new compounds (GdNisub(0.2)Sisub(1.8), Gdsub(2)Nisub(1-0.8)Sisub(1-1.2), Gd 5 NiSi 4 ) are found. On the base of Gd 2 Si 3 compound up to 0.15 at. Ni fractions, an interstitial solid solution is formed up to 0.25 at Ni fractions dissolution continues of substitution type. The Gd-Ni-Si system is similar to the Y-Ni-Si system

  20. Internal carbonitriding behavior of Ni-V, Ni-Cr, and Ni-3Nb alloys

    Allen, A.T.; Douglass, D.L.


    Ni-2V, Ni-5V, Ni-12V, Ni-10Cr, Ni-20Cr, and Ni-3Nb alloys were carbonitrided in C 3 H 6 and NH 3 gas mixtures (bal H 2 ) over the range 700--1,000 C. Carbonitridation of Ni-12V and Ni-20Cr in C 3 H 6 /NH 3 /H 2 (1.5/1.5/97 v/o) and (1.5/10/88.5 v/o) produced duplex subscales consisting of near-surface nitrides with underlying carbides. Growth of each zone obeyed the parabolic rate law under most conditions. The presence of carbon generally did not effect the depth of the nitride zones compared to nitriding the alloys in NH 3 /H 2 (10/90 v/o). However, at 700 C, the nitride zones were deeper in the carbonitrided Ni-V alloys and Ni-20Cr. The presence of nitrogen generally increased the depth of the carbide zones in Ni-12V and Ni-20Cr compared to carburizing these alloys in C 3 H 6 /H 2 (1.5/98.5 v/o). VN, CrN, and NbN formed in Ni-V, Ni-Cr, and Ni-Nb alloys, respectively, whereas the underlying carbide layers contained V 4 C 3 in Ni-12V, Cr 3 C 2 above a zone of Cr 7 C 3 in Ni-20Cr, and NbC in Ni-3Nb. The solubilities and diffusivities of nitrogen and carbon in nickel were determined. Nitrogen and carbon each exhibited retrograde solubility with temperature in pure Ni in both carbonitriding environments. Nitrogen diffusion in nickel was generally lower in each carbonitriding mixture compared to nitrogen diffusion in a nitriding environment, except at 700 C when nitrogen diffusion was higher. Carbon diffusion in nickel was generally higher in the carbonitriding environments compared to carbon diffusion in a carburizing environment

  1. Nipah Virus (NiV)

    ... Form Controls Cancel Submit Search the CDC Nipah Virus (NiV) Note: Javascript is disabled or is not ... gov . Recommend on Facebook Tweet Share Compartir Nipah virus (NiV) is a member of the family Paramyxoviridae , ...

  2. Experimentation to seek the local speciality in kWh of P.V. system, and a study of its measuring method and instruments and apparatus; Taiyoko hatsuden system no jibetsu hatsudenryo no chiiki tokusei wo motomeru jissho shiken narabini, sono sokutei kansoku no hoho kiki ni kansuru kenkyu

    Anno, T.


    Introduced in this paper are some problems that the author encounters in relation with a 2.6kW photovoltaic power generation system installed at the author`s residence for the purpose of measuring the hourly amounts of generated power. Giving rise to questions in the inverter and the control system are the conversion efficiency under a partial load, the scope of little amounts that are omitted, the maximum power point tracking system and its performance, etc. The author wants to learn how to land on an appropriate conductor thickness and to know the special specifications if any for heavy-snow regions and their effect. Much has been learned from presenters, moderators, and participants at scientific events and through private talks. Although it seems that there exists some relationship between the maximum power point tracking system and the diameter of conductors suitable for the system, yet the manufacturers fail to give clear-cut answers. The author thinks that end-users find many black box-like parts in the system, which the author leaves uncared for now for later study. It is learned that there is no specification intended exclusively for heavy-snow regions. The author`s system is in operation with hourly output recording and data accumulation started. 2 figs.

  3. Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)


    To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

  4. Ni República parlamentaria ni presidencialista

    Álvarez Tardío, Manuel


    Revista de Estudios Políticos (Nueva Época), Núm. 123. Enero-Marzo 2004 Este trabajo está dedicado al estudio de un aspecto básico del sistema político de la II República española (1931-1936): el modelo de presidencia de la República y de relaciones de la misma con el parlamento y el gobierno. Aquí se sostiene que la Segunda República, de acuerdo con su Constitución, no fue un régimen parlamentario ni presidencial. Combinó de forma extraña y ambigua elementos de ambos modelos. Probablement...

  5. Fiscal 1997 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1997 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)



    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, equipment and devices were procured for the product oil reforming facilities and their installation was partly accomplished. In the coal injection operation, a 60-day slurry operation was conducted, using coal types of the upper limit and lower limit qualities, for expanding the scope of coal types applicable to the NEDOL process and for exploring optimum conditions, and another operation of 37 days was conducted using Chinese coal and Chinese-prepared liquefaction catalysts, and the two operations were studied for difference in yields and in operationality. Characteristics of the liquefaction reactors were investigated and basic studies were made relative to the physical property of the yielded coal oil. In the operation for maintenance, the 1st liquefaction reactor was singly operated for an 8-day slurry operation, which was to check the progress of liquefaction in a 1-reactor setup. Concerning the reforming of the product oil, the hydrogenation reactors were checked for their response to temperature control. Moreover, hydrogenation solvents were produced for the PSU and for China. (NEDO)

  6. Study of QoS control and reliable routing method for utility communication network. Application of differentiated service to the network and alternative route establishment by the IP routing protocol; Denryokuyo IP network no QoS seigyo to shinraisei kakuho no hoho. DiffServ ni yoru QoS seigyo no koka to IP ni yoru fuku root ka no kento

    Oba, E.


    QoS control method which satisfies utilities communication network requirement and alternative route establishment method which is for sustaining communication during a failure are studied. Applicability of DiffServ (Differentiated Service), one of the most promising QoS control method on IP network and studying energetically in IETF WG, is studied and it is found most application used in the utility communication network except for relaying system information could he accommodated to the DiffServ network. An example of the napping of the utility communication applications to the DiffServ PHB (Per Hop Behavior) is shown in this paper. Regarding to the alternative route, usual IP routing protocol cannot establish alternative route which doesn't have common links and nodes in their paths for a destination. IP address duplication with some modification of routing protocol enables such alternative route establishment. MPLS, distance vector algorithm and link state algorithm are evaluated qualitatively, and as a result, we found MPLS is promising way to establish the route. Quantitative evaluation will be future work. (author)

  7. Developments of DPF systems with mesh laminated structures. Performances of DPF systems which consist of the metal-mesh laminated filter combustion with the alumina-fiber mesh, and the combustion device of trapped diesel particles; Mesh taso kozo no DPF no kaihatsu. Kinzokusen to arumina sen`i mesh ni yoru fukugo filter to filter heiyo heater ni yoru DPF no seino

    Kojima, T; Tange, A; Matsuda, K [NHK Spring Co. Ltd., Yokohama (Japan)


    For the purpose of continuous run without any maintenance, new DPF (diesel particulate filter)systems laminated by both metal-wire mesh and alumina-fiber mesh alternately, are under the developments. The perfect combustion of trapped diesel particulate can be achieved by a couple of the resistance heating devices inserted into the filter. 5 refs., 7 figs., 3 tabs.

  8. Measurement of turbulent flow fields in a agitated vessel with four baffles by laser-doppler velocimetry. Analysis with periodic averaged velocity profiles; Baffle tsuki heiento kakuhan sonai nagare no LDV ni yoru keisoku. Shuki heikin sokudo bunpu ni yoru kaiseki

    Suzukawa, K [Ube Industries, Ltd., Tokyo (Japan); Hashimoto, T; Osaka, H [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering


    The 3-D flow field relative to a rotating paddle blade is acquired by synchronizing LDV measurements with the output of a shaft-mounted encoder. This makes it possible to capture the impeller stream velocity field, including the details of the discharge flow region behind the blades. Mean velocities ensemble-averaged between a specific impeller blade pair (over 90deg) show the extent of periodicity and the passage and structure of the discharge flow region. Pumping capacities are determined at both sides of impeller and tip of impeller, and it is shown that the radial jet is a consequence of fluid entrainment into the discharge flow region. Mean velocities taken in a rotating frame of reference reveal a significant periodic variation near the impeller than those taken in a fixed frame. 13 refs., 12 figs., 1 tab.

  9. Suppression of inducer stall based on inlet recirculation in a centrifugal impeller. 1st Report. Improvement in stall limit by ring groove arrangement; Enshin haneguruma iriguchi junkanryu ni yoru inducer shissoku no yokusei. 1. kanjoko ni yoru shissoku genkai no kaizen

    Ueki, H.; Ishida, M.; Sakaguchi, D.; Sun, Z. [Nagasaki University, Nagasaki (Japan). Faculty of Engineering


    A ring groove arrangement is proposed to suppress unstable flow or surge in a centrifugal blower. The ring groove arrangement connects the upstream position of impeller inlet and the inducer throat tip through a bypass. The recirculation flow 'vas formed by the pressure difference between the two positions, and the recirculation flow rate was changed by increasing the ring groove widths. The inlet recirculation results in a decrease in the flow rate of unstable flow inception, and an up to 800 improvement in stall limit was obtained by the ring groove arrangement at a small expense of the delivery pressure drop. The improvement of stall limit in the present experiment seems to be mainly due to decrease in flow incidence based on the inlet recirculation flow. Tre flow incidence decreases more as the recirculation flow rate increases, thus resulting in a larger improvement in stall limit. (author)

  10. Fiscal 1996 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1996 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)



    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, detailed designs were prepared for product oil reforming facilities and some equipment and devices were procured. In addition, the 3rd liquefaction reactor cone section and the neutron attenuation-aided measuring device were refurbished. In the injection of coal, a 62-day and 23-day slurry injection operations were accomplished using Tanito Harum coal, when the impact imposed on the yield of the product, etc., by the change of liquefaction catalysts and by gas phase hydrogen concentration enriching conditions was investigated, and the unit was examined for operationality. During a 42-day operation for maintenance, the unit was operated using only the slurry heater for the investigation of the initial reaction in liquefaction, and studies were conducted about the heater exit temperature, G/L (gas-liquid ratio), and the effect to ensue from the use of a different solvent. In the effort to develop and evaluate new materials, implantation tests were conducted for metallic materials and the 3rd liquefaction reactor was subjected to a non-destructive inspection. Wastewater from the process was examined for quality, and environment-related measurements were performed for the atmosphere. (NEDO)

  11. Fiscal 1998 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1998 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)



    The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. For the modification of facilities, product oil reforming facilities were installed. In the coal injection operation, a 59-day slurry operation was carried out using Tanito Harum coal, which was for the evaluation of the reforming effect under the product reforming conditions, operationality, and liquefaction characteristics. A 37-day slurry operation was also performed using Chinese coal, which was intended to pursue improved cost performance and to collect the light oil fraction in the flow of reforming operation. In the operation for maintenance, investigations were conducted into conditions for hydrogenation in a 1-through operation involving the solvent hydrogenation process and the normal pressure distillation facilities and into the effect of pre-hydrogenation solvent properties, which aimed at grasping the effect of product oil reforming measures and their influence on operationality. In the survey of environments, the properties of wastewater from the liquefaction process using Tanito Harum coal were studied and toxicity evaluation tests were conducted for activated sludge. (NEDO)

  12. Microstructural development in NiAl/Ni-Si-B/Ni transient liquid phase bonds

    Gale, W.F.; Orel, S.V.


    A transmission electron microscopy (TEM) based investigation of microstructural development during transient liquid phase bonding of near-stoichiometric NiAl to commercial purity nickel is presented in this article. The work described employed Ni-4.5 wt pct Si-3.2 wt pct B (BNi-3) melt-spun interlayers. The precipitation of both Ni-Al based phases and borides within the joint and adjacent substrate regions is discussed. The article considers martensite formation (within the NiAl substrate) and the precipitation of L1 2 type phases (both within the joint and at the interface with the NiAl substrate). The relative roles of the two substrate materials (NiAl and Ni) in the isothermal resolidification process are identified. The preferential formation of Ni 3 B boride phases in the Ni substrate near the original location of the Ni substrate-joint interface is discussed and contrasted with the absence of similar events in the NiAl substrate

  13. Ni landsbyer i Danmark

    Larsen, Jacob Norvig

    Denne rapport beskriver en evaluering af statsstøttede forsøg med at styrke og udvikle mindre lokalsamfund. Forsøgene er gennemført i ni kommuner. Da der i disse år er stor opmærksomhed om de små byers og samfunds udviklingsmuligheder, har erfaringerne fra forsøgsprojekterne bred interesse. Forsø...

  14. Generalized report on the research cooperation promoting project. Research cooperation related to the mine waste water treatment technology utilizing biotechnology; Kenkyu kyoryoku suishin jigyo sokatsu hokokusho. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku



    This paper is a generalized report in relation with the mine waste water treatment technology utilizing biotechnology, from among the promotion projects for research cooperation with China. Ferric iron (Fe{sup 3+}), which precipitates at low pH, is produced by utilizing bacteria which derives energy from oxidizing ferrous iron (Fe{sup 2+}) in the waste water, and the iron is precipitated and removed by using low-cost calcium carbonate as a neutralizing agent. Joint researches and developments have been carried out on selection of optimal kinds of bacteria, cultivation of bacteria oxidizing iron at high efficiency, optimal removal system of heavy metals in mine waste water, and recovery of useful resources. Japanese engineers were sent to sites in China, Chinese researchers were received in Japan, and pilot plants were operated and studied. For the purpose of proliferating and enlightening the result of the project, a seminar was held in Beijing in February 1998. In order for the achievements derived up to fiscal 1998 to be used in diverse fields, fiscal 1999 will carry out follow-ups, including assistance, for the voluntary researches performed by China. The follow-ups will also include confirmation on the state of testing the iron oxidizing bacteria technology, technical guidance, and analyses and discussions on the data. (NEDO)

  15. Study of promotion of CO2 fixation by the environmental improvement in the coral reef area; Kansho chitai ni okeru kankyo kaizen ni yoru CO2 kotei sokushin no kenkyu

    Maruoka, T.; Ishitani, H.; Matsuhashi, R.; Yamada, K.; Komiyama, H.; Kraines, S. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering


    A study was conducted on how to fix CO2 in the ocean using coral reefs. Coral reefs have extremely high primary productivity ( production quantity of organic matters by photosynthesis) and are expected to be resources to fix CO2 when the quantity of photosynthesis exceeds the quantity of CO2 emitted in association with formation of calcium carbonate skeleton. If organic substances produced in coral reefs are well carried into the open sea, those are settled down on deep beds, which enables the storage into the ocean. At the coral reef floating in the ocean, it is not very deep inside and the seawater stays there, but it has a steep depth outside. By the numerical calculation, an examination was made on how the waterflow changes when making the flow path of seawater between the inland sea and open sea. From the actual calculation of an atoll, it was found that seawater comes in and out from the open sea to the inland sea near the opening of the atoll in accordance with the high tide and ebb tide, but the water stays at the deep bottom of the atoll. When installing a channel with a 10m depth at the portion where the water flows softly, the seawater was actively exchanged. 6 refs., 4 figs.

  16. FY 1994 report on the cooperative research on the biological use mine wastewater treatment technology; 1994 nendo bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku hokokusho



    In this project, a pilot plant for mine wastewater treatment facilities using Thiobacillus ferrooxidans was installed at the Wushan mine in China to study the operation using the bacteria habitable in this mine. The project aims at establishing the mine wastewater treatment technology using the method of Thiobacillus ferrooxidans in China. The field survey and study in Japan were carried out. In the field survey, the technical guidance was given for incubation method, neutralization experiment method and analysis method of Thiobacillus ferrooxidans. In the study in Japan, one kind of bacteria to be used was selected in the 'selection test for the optimum kind of bacteria,' and a study was made which was titled 'Study of mine wastewater treatment using the method of Thiobacillus ferrooxidans which is suitable for the mine site.' In 'Study of the optimum removal of heavy metal in mine wastewater,' a table test of sulfide precipitation method was conducted on copper removal/recovery to make formation conditions of copper sulfide clear. The conditions obtained were reflected in 'Study of mine wastewater treatment by the method of Thiobacillus ferrooxidans which is suitable for the mine site,' and various conditions for bacteria oxidation process were studied. The paper surveyed characteristics of heavy metal and temperature of Chinese strains. Further, the basic data were acquired which contribute to the production of inorganic flocculants. (NEDO)

  17. Fiscal 1999 survey report. Part 2. Research study on restraint of carbon dioxide generation by green chemistry; 1999 nendo green chemistry ni yoru CO{sub 2} hassei yokusei ni kakawaru chosa kenkyu. 2



    In connection with green chemistry, a concept of bringing paradigm shift to chemical technologies as something that makes reduction in environmental load compatible with economic activities; surveys were made this year on the developments of fine chemicals from renewable resources such as cellulose among the cases of developing chemical substances/products to be called 'green chemicals' reducing environmental load; developments of surfactants produced by certain microorganism, plastic additives with reduced pollutant loads, particularly fire retardants and environmentally benign reactant solvents; concept of green chemistry in the development of chlorofluorocarbon-alternatives; and up-to-date technological level concerning a design method of chemical materials and an estimation method for chemical safety using quantum chemistry calculation. In regard to the chemical materials and products intrinsically containing a certain level of risk, R and D should be reinforced and accelerated in the future on the alternative materials/products reducing their toxicity. In this case, along with the importance of discussing compatibility of technological possibility with economical adaptability, sociological study seems to be necessary in incorporating environmental load reduction into economic evaluation. (NEDO)

  18. Recovery of gold with ion exchange resin from leaching solution by acidothioureation. Ion kokan jushiho ni yoru ryusan sansei chio nyoso kinshinshutsueki kara no kin no kaishu ni kansuru kenkyu

    Nakahiro, Y.; Ninae, M.; Kusaka, E.; Wakamatsu, T. (Kyoto University, Kyoto (Japan). Faculty of Engineering); Horio, Y. (Yamaha Co. Ltd., Tokyo (Japan))


    Recovery of gold with ion exchange resin from leaching solution by acidothioureation, and elution of gold from ion exchange resin with gold were studied experimentally. As the result of batch adsorption experiments of Au(TU){sub 2}{sup +} into various kinds of ion exchange resins, strong acidic cation exchange resin was most suitable, and gold was fully adsorbed into such resin in the pH range from 1.2 to 2.0 without any effects of thiourea in the leaching solution on adsorption of gold. As the result of batch elution experiments in various kinds of eluates, copper was eluted in HNO{sub 3}(1 N) + H{sub 2}O{sub 2}(1wt%) elute, both iron and zinc in NH{sub 4}NO{sub 3}(0.5 M) elute, and gold in Na{sub 2}S{sub 2} O{sub 3}(0.05 M) elute resulting in the recovery of gold. As the result of column elution experiments, Amberlite 200C was most effective among some ion exchangers used for recovery of Au(CS(NH{sub 2}){sub 2}){sub 2}{sup +}. 16 refs., 15 figs.

  19. Report on the research cooperation promoting project in fiscal 1998. Research cooperation related to the mine waste water treatment technology utilizing biomass; 1998 nendo kenkyu kyoryoku suishin jigyo hokokusho. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kyoryoku



    This paper describes the achievement in relation with the mine waste water treatment technology utilizing biomass, from among the promotion projects for research cooperation with China. Waste water is converted into ferric iron (Fe{sup 3+}), which precipitates at low pH, by utilizing iron oxidizing bacteria which use ferrous iron (Fe{sup 2+}) in the waste water as the energy source, and is precipitated and removed by using low-cost calcium carbonate as a neutralizing agent. Fiscal 1998 has performed eight site surveys with 47 persons in total. The main survey items are the study and guidance of pilot plant operation and the survey on measures to prevent occurrence of contamination by heavy metals in Wushan Mine. Additional site surveys were made at Dexing Mine and Yinshan Lead/Zinc Mine. Continued from fiscal 1997, consumables required for the pilot plant were purchased, and items of the bench-scale testing equipment used by Japan for domestic researches (an oxidation and neutralization testing equipment and a copper recovering and testing equipment) were transported to China. The operation research data of the pilot plant were put in order and analyzed. This paper summarizes the concept design of the shaft waste water treatment facilities for the north mine in Wushan Mine, and the surveys on measures for heavy metal contamination sources. (NEDO)

  20. Effect of temperature on degradation of musty odour compound producing by cyanobacteria, Phormidium tenue by microflagellate, Monas guttula; Benmochu Monas guttula ni yoru kabishu sansei sorui Phormidium tenue no bunkai ni oyobosu ondo no eikyo

    Lee, B.; Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Sugiura, N. [Ibaraki Prefectural Waterworks, Ibaraki (Japan); Inamori, Y.; Nishimura, O. [National Inst. for Environmental Studies, Tsukuba (Japan); Higashi, T. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical


    Biodegradation characteristics of cyanobacteria, Phormidium tenue and its metabolites, 2-methylisoborneol (MIB) by protozoan microflagellate, Monas guttula, and the effect of temperature on them were examined in batch culture experiment. The flagellate was found to predate on P. tenue favorably as a food source within a wide temperature range from 10degC to 30degC. Specific growth rate ({mu}) and generation time (t{sub d}) of the flagellate were 4.6 day{sup -1} and 3.5 h{sup -1}, respectively at 20degC and 30degC, whereas in the case of 10degC the lag values of {mu} and t{sub d} were obtained by 1.9 fold in comparison with the removal ratio of 61% at the first cultivation day and that of 99% at the 2nd day at 30degC, while at 20degC the removal was only about 30% in the first day, but P. tenue could be perfectly reduced at the 2nd day. Although the reduction rate of the P. tenue was slow at the lower temperature of 10degC, the removal reached 98% in the 7th day. Removal rate of P. tenue by the flagellate increased with the increase in temperature and reached the maximal value with 4.0 h{sup -1} at 30degC. The flagellate could contribute to the degradation of MIB, although the degradation was lower than that of P. tenue. It was found that the microflagellate could favorably predate on P. tenue and degrade its metabolite, MIB emitting musty odor in a wide range of temperature. 27 refs., 8 figs., 3 tabs.

  1. Achievement report for fiscal 1984 on Sunshine Program. Research on liquefaction characteristics different between coal types and on technical physical properties; 1984 nendo tanshu ni yoru ekika tokusei to kogakuteki busseichi ni kansuru kenkyu seika hokokusho



    Liquefaction characteristics of coal specimens, collected from many locations across the world, are determined so as to make clear the correlations between coal type and liquefaction reactivity. Conducted for this purpose are the analysis of chemical structures of the specimens, liquefaction tests in an autoclave using various catalysts and medium oils, liquefaction tests in a 0.1t/d bench plant, investigation of the constituents of the generated oil and their separation, and the secondary stabilization treatment for the commercialization of the product. The reaction tower is kept under constant conditions, the state of the liquid mixture in the reaction tower is evaluated by tracking the flow of coal out of the reaction tower after switchover from anthracene oil to coal paste, the gas flow in the reaction tower is estimated by tracking time-wise changes in the concentration level of inert gas at the reaction tower outlet port, the inert gas having been injected in pulses into the reaction system operating under the reaction conditions. For the implementation of the above-mentioned steps, a system is designed and constructed for directly collecting samples from the vapor phase section in the reaction tower operating under given reaction conditions (temperature: 400-450 degrees C, pressure 150-300kg/cm{sup 2}), and experiments are conducted to collect gas/liquid equilibrium data in the reaction tower under the given reaction conditions. (NEDO)

  2. Relation between front suspension layout and handling performance. Analysis depending on the Taguchi method and ADAMS; Front suspension layout to soda tokusei no kankei ni tsuite. Kiko kaiseki gengo wo mochiita hinshitsu kogaku ni yoru kaiseki

    Okada, K [Daihatsu Motor Co. Ltd., Osaka (Japan)


    A variation of suspension layout gives an influence to the vehicle dynamics. Examined the suspension layout variation to make the handling performance change small. Analyzed the effect of suspension layout variation about steering response delay and gain besides the tire wear effect and movable load. 3 refs., 12 figs., 4 tabs.

  3. Report on the FY 1999 investigational survey on the activation of oxygen electrode by ion implantation; 1999 nendo ion chunyuho ni yoru sanso denkyoku no kasseika ni kansuru kenkyu chosa hokokusho



    The oxygen electrode is important as the base electrode for water electrolysis and fuel cell, but to move it, overvoltage (activated energy) in addition to equilibrium voltage is necessary, which leads to the lowering of energy efficiency. By forming the active spot by ion implantation, the lowering of overvoltage was studied. The implantation of Ru{sup +} ion in Ruthenium dioxide thin film electrode reduced the oxygen generating overvoltage by 15-20mV. Even in the oxygen reduction, activity was also increased. The chemical composition of thin film does not change by ion implantation. The increase in activity is based on a physical change which is called the surface defect formation. The layer of ion implantation is composed of microcrystals, which is thought to contribute to the formation of any active spot. Ions were implanted in Pt electrode as a practical use material, and even in the oxygen reduction of Pt, a possibility of heightening activity by ion implantation was admitted even in the oxygen reduction of Pt. The generation of high activity oxygen by ion plantation and development of oxygen reduction electrode were established as one method as a rule. (NEDO)

  4. Report on evaluation of research and development of direct steel-making using high-temperature reducing gas. Phase 1. Draft; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho (an)



    Described herein is development of direct steel-making using high-temperature reducing gas. A light hydrocarbon fraction (boiling point: 230 degrees C or lower), produced by steam cracking of vacuum residua, is reformed into a reducing gas in the presence of steam, using heat to be supplied by a nuclear plant which produces high-temperature gases for various purposes. This reducing gas is then supplied to a plant for producing reduced iron. This project has established basic techniques for designing, constructing and operating a direct steel-making pilot plant, to be connected to a 50 MWt high-temperature gas test furnace. The closed iron-making system and greatly reduced SOx emissions to several fractions of the current level are some of the expected effects. The environmental impacts of the high-temperature gas furnace will be on a level with those associated with a light-water reactor. Cracking and gasification of vacuum residua, which has found limited purposes so far, should expand its applicable areas and reduce dependence on fossil resources, leading to diversification of energy sources. The overall thermal efficiency of the high-temperature gas furnace is expected to increase to at least 60%, because its high-temperature gases of around 1,000 degrees C can be used for heating processes, and the waste heat can be further used for generation of steam for power production. (NEDO)

  5. Preparation of ZrO2 thin films by CVD using H2-CO2 as oxidizer. H2-CO2 wo sanka gas ni mochiita CVD ho ni yoru ZrO2 maku no sakusei

    Aizawa, M; Kobayashi, C [Toto Ltd., Kitakyushu (Japan); Yamane, H; Hirai, T [Tohoku University, Sendai (Japan). Institute for Materials Research


    This report describes an outline on the results of investigation on the formation of ZrO2 films from [beta]-diketone chelate of Zr using H2/CO2 as oxidizing gas by application of the CVD method at a temperature as high as 1000[degree]C. The deposition rate is 4[mu]m/h at 650[degree]C, increases with rise of temperature and reaches 10[mu]m/h at 900-1000[degree]C. No lowering of the rate at high temperature seems to be caused by temperature dependence of water (increase of water concentration above 850[degree]C). The physical form of ZrO2 is black and amorphous at 650[degree]C; grey and tetragonal at 850[degree]C; white, monoclinic and tetragonal at 950-1000[degree]C. All of these films showed a fine-grain, polycrystalline structure at any temperature and became white by heat-treatment at 1100[degree]C for 100h. This treatment gave no change to amorphous films but transformed tetragonal films and the mixture films of tetragonal and monoclinic crystals into white monoclinic Zr films. This may be because oxygen defects were present in black and grey films of low deposition temperature due to insufficient oxydation of raw material by H2O. Instability of tetragonal crystals seems to be attributed to participation of oxygen defects. In conclusion, possibility of high-temperature film formation was confirmed. 17 refs., 4 figs.

  6. Researches regarding a constructing problem of a PV system. Part 1. Conscious investigation by means of a questionnaire survey; Taiyoko hatsuden system ni okeru kenchikuteki shomondai no kenkyu. 1. Anketo chosa ni yoru ishiki chosa

    Nakajima, Y; Yamazaki, R; Kuroki, T [Kogakuin University, Tokyo (Japan)


    The installation and introduction of photovoltaic power generation systems (PVS) in buildings are growingly expected in the construction field from now, coupled with the marketing of a solar cell module as a product for a construction material in the form of an external wall or a roof material for example. For this purpose, it is necessary at first to summarize problems that may arise at the time of or after the installation of PVS as a product. This paper examines an opinion poll, degree of recognition, current problems, etc., of PVS as a result of a questionnaire survey given to engineers and architects engaged in the actual construction business. The degree of recognition and interest was very high. Consultation or request for PVS installation was much more than predicted in numbers. Roughly 50% of the respondents reacted positively for the future installation request of PVS and, combined with the respondents who answered to look into the installation tentatively, not less than 90% were of a forward-looking opinion. The 85% of the respondents was not aware of the monitor business system for residential PVS. Further, the survey clearly brought out the importance of cost problems. 1 ref., 11 figs., 3 tabs.

  7. Report on the Sunshine Project in fiscal 1990. Studies on liquefaction characteristics by coal types and on engineering properties; 1990 nendo tanshu ni yoru ekika tokusei to kogakuteki busseichi ni kansuru kenkyu hokokusho



    This paper describes the achievements at the Government Industrial Development Laboratory, Hokkaido in the Sunshine Project in fiscal 1990. Surveys were carried on different catalytic activities for co-liquefaction of various types of coals. The Ru system was found preferable in acquiring fatty family products of low boiling points. Reactions of co-liquefaction constituents do not progress independently, but have positive interaction. Adding Ru is effective in accelerating hydrogenation of condensed aromatic rings and hydrogenation of cleaving nucleus, but in view of the hydrogenating decomposition capability, the Mo-system may be better. In a liquefaction plant test, diesel oil was manufactured by reforming and improving the Yallourn coal light oil. However, the oxygen content was too high, aggravating the temperature distribution control in catalyst bed, and not having achieved the intended denitrification rate. Discussions were given on co-liquefaction of the depressurization residues of Cold Lake (CLVB[vacuum bottom])/Athabasca (ATVB) and Battle River coal. The CLCVB and ATVB were turned into lower molecules easily through hydrogenation treatment. The reaction characteristics reflected the characteristics of medium oil. Depolymerization of coal has progressed faster in ATVB. In the study on the engineering property values, discussions were given on behavior of solid particles in a bubble column, and gas hold-up of slurry. (NEDO)

  8. Investigation on the dynamic response and strength of very long floating structures by beam modeling on an elastic foundation; Dansei shishojo no hari model ni yoru chodai futai kozo no doteki tawami kyodo tokusei ni kansuru kosatsu

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering


    A very large floating structure was replaced with the beam on an elastic foundation to examine the response characteristics in waves. Another evidence was regularly and numerically given for the basic characteristics of a very large floating body Suzuki found. New information was also obtained. The frequency response is mainly classified into a wave number control area and proper frequency control area when buoyancy elasticity exists. When the buoyancy structure is long and flexible, the proper frequency becomes continuous and the frequency control area becomes a resonance area. In the wave number control area, the Suzuki`s characteristic wave number becomes a control parameter, and various characteristic values are indicated by characteristic wave numbers. The response in the wave number control area becomes quasi-static when the distribution mass of buoyancy is fully small. The design in which the distribution mass of buoyancy is fully large must be avoided. In the displacement amplitude, the mass on the free end is severest. The proper frequency of vertical vibration relatively moves to the high-frequency side when buoyancy is considered as an elastic foundation. Attention must be thus paid to the proper frequency of vibration on the horizontal surface. 9 refs., 12 figs., 3 tabs.

  9. Heat and mass transfer in a reforming catalyst bed. Analytical prediction of distributions in the catalyst bed; Kaishitsu shokubaiso ni okeru netsu oyobi busshitsu ido. Suchi kaiseki ni yoru sonai bunpu no yosoku

    Usami, Y [Tokyo Electric Power Co. Inc., Tokyo (Japan); Fukusako, S; Yamada, M [Hokkaido University, Sapporo (Japan)


    Heat and mass transfer characteristics within a reforming catalyst bed have been analytically investigated. A numerical analysis was carried out in a two-dimensional steady-state model of reforming catalyst layer. Reforming tube was filled with catalyst and the tube wall was uniformly heated, a mixture of steam and methane was reformed through the catalyst bed. Predicted temperature, formed gas composition, methane conversion rate, and heat transfer coefficient distributions in the catalyst layer showed good agreement with experimental data. The effects of space velocity, steam carbon molar ratio, and wall temperature on the heat transfer coefficient were analytically presented. From temperature and composition distributions simulated by two-dimensional analysis, the effects of these factors above mentioned and diffusion on the transport phenomena were qualitatively predicted. (author)

  10. Natural convection heat transfer in an anisotropic porous cavity heated from the side. 1st Report. Theory; Tosuiritsu ni ihosei wo yusuru howa takoshitsu sonai no sokuho kanetsu ni yoru shizen tairyu netsu dentatsu. 1. Riron kaiseki

    Kimura, S [Kanazawa University, Ishikawa (Japan). Faculty of Engineering; Okajima, A [Kanazawa University, Ishikawa (Japan)


    Natural convection heat transfer and flow structure in an anisotropic porous medium of square cavity saturated with Boussinesq fluid has been studied analytically and numerically. Based on asymptotic analysis three distinctive regimes are found depending upon the magnitude of permeability ratio K. In the vicinity of K=1 the average Nusselt number and fluid velocity are scaled with (KRa){sup 1/2} when either K or the Rayleigh number Ra is varied. In the limit of K {yields} 0 the heat transfer across the cavity approaches to the conductive state, and the convecting velocity, which is primarily in the vertical direction, is scaled with KRa. In the other end of spectrum, namely K {yields} {infinity}, the average Nusselt number and the convecting velocity are scaled with Ra and independent of K. The asymptotic results are verified with two-dimensional numerical calculations. The ranges of K of the respective regimes are also determined based on the numerical results. 12 refs., 12 figs.

  11. Research cooperation project in fiscal 1999. Research cooperation on a technology to treat well waste water by utilizing biomass (follow-up); 1999 nendo bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku (follow up)



    The research cooperation project on a technology to treat well waste water by utilizing biomass has used as the object the well waste water from the north mine in the Wu Shan mine in Jiangxi Province. The research included surveys on properties of the well waste water from the subject mine by means of the site survey, discussions on treatment conditions based on studies in Japan, and discussions on factors for designing a full size facility as a result of pilot plant operation research. The Japanese side has transported to Beijing the bench-scale testing equipment used for the studies in Japan (an oxidation and neutralization testing equipment and a copper recovery testing equipment). In the present follow-up project, supports were provided to the research and development activities performed voluntarily by the Chinese side by using the above bench-scale testing equipment through guiding the tests at the site and supplying consumables. Certain bacteria have capability to oxidize ferrous ions in the mine well waste water into ferric ions. Utilizing these bacteria results in sedimentation of iron oxides in lower pH zones than in the conventional method, making removal of heavy metals from the well waste water possible. As a result, such effects may be expected as reduction in chemical cost, and reduction of quantity of the produced sediments. (NEDO)

  12. Estimation of a subsurface structure by using shallow seismic engineering exploration system with multiple function (SWS); Takino danseiha tansa sochi (SWS) ni yoru senbu chika kozo tansa ni tsuite

    Liu, Y [Beijing Shuidian Research Institute of Geophysical Surveying, Beijing (China); Ling, S [Nihon Nessui Corp., Tokyo (Japan); Okada, H [Hokkaido University, Sapporo (Japan)


    The Beijing Shuidian Research Institute of Geophysical Surveying has performed ocean seismic exploration in the area where the Fujian Pingtan bridge was planned to be constructed. The elastic wave exploration device is of a multi-functional type. The device has functions of acquiring, processing and analyzing data in seismic exploration using the reflection method, and can visualize subsurface conditions at the same time as performing the exploration. The planned bridge building area spans over a sea area of about 3500 m long with water depths from several meters to 30 meters. The foundation bed consists of dacite lithologic tuff and granodiorite. The seal level varies from 4.0 m to 4.8 m between high and low tides. According to the result of other measurements, the elastic wave propagation velocities of the sea water were found from 1475 to 1485 m/s, and the elastic wave propagation velocities at the surface bed of the sea bottom were from 1550 to 1700 m/s. The exploration used a workboat which moves at a constant speed while maintaining the offset between a transmitting source and a receiving source constant, executing vibration transmitting, receiving and recording all on the sea. The result of the exploration revealed that neither obstacles such as sunken ships nor marks of occurrence of ocean bottom landslides were present. 1 ref., 5 figs.

  13. Development of ELID mirror surface grinding by cast iron bond grinding wheel. Ohkochi memorial technology prize; Chutetsu bond toishi ni yoru denkai inpurosesu doresshingu (ELID) kyomen kensakuho no kaihatsu. Okochi kinen gijutsusho jusho ni yosete

    Omori, H.; Takahashi, I. [Institute of Physical and Chemical Research, Tokyo (Japan); Nakagawa, T. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Hagiuda, Y.; Karikome, K. [Tokyo Metropolitan College of Aeronautical Engineering, Tokyo (Japan)


    Development was accomplished on the electrolytic in-process dressing (ELID) mirror surface grinding process using a cast iron bonded grinding wheel. This paper describes the history of the development, which may be summarized as follows: a study was begun on powder forging of cutting chips in 1970; a research was started on powder forging of decarburized cast iron powder; developments were made on powder metallurgy of cast irons and cast iron bonded lapping tools in 1980, and cast iron bonded diamond grinding wheels were put on the market; a high-efficiency grinding process using MC and cast iron fiber-bonded grinding wheels were developed in 1985 and the grinding wheels made therefrom were put on the market; and a study was begun on the ELID grinding in 1987, and marketing was started on power supply, grinding liquid and tools for the ELID grinding process in 1990. Discussions on converting raw materials for the powder forging into cutting chips have triggered developing the cast iron bonded grinding wheel. The cast iron bonded diamond grinding wheel improves dressability and sharpness of conventional grinding wheels. The grinding wheel is fabricated by mixing carbonyl iron powder, diamond grinding grains and cast iron powder, pressing the mixture in a die, sintering it at 1140 degC, and assembling and dressing the sinter. The grinding stone can grind high-tech materials. 4 figs.

  14. Feasibility study of energy conservation measures to be taken in international cooperation in the metal mining industry; 1998 nendo kinzoku kokogyo ni okeru kokusai kyoryoku ni yoru sho energy taisaku jisshi no kanosei chosa



    In the investigation, reviewing detailed processes of mining industries, current situation for saving energy among mining and materials production industries are executed. Discussions on the evaluation methods for global warming, possibility of saving energy, location of smelters, etc. are made among the investigation. As the results, energy saving for the industries in japan is in the highest level all over the world and the effort to improved it almost reaches their limits at the moment. However, considering global environment, there are still possibilities to reduce the impact to the environment. Since the evaluation methods of saving energy for the global environmental has not fixed yet, worldwide discussions for the methods area expected. For the remarkable energy saving, instalment of new process is essential. For the achievement of the saving, continuous research and development are necessary. For the sustainable development of mineral industries and the promotion of global environmental protection, governmental backup and the contribution by national institutes are expected. (NEDO)

  15. Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho



    Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

  16. Report on research cooperation for bio-aided treatment of waste water from pits, conducted in FY1997; 1997 nendo bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku hokokusho



    This research cooperation promotion project was implemented to develop techniques for preventing water pollution by waste water from pits in mines in China and thereby contributing to environmental preservation by studying to select optimum bacteria, culture the bacteria for high-efficient oxidation of iron, efficiently remove heavy metals from waste water, develop waste water treatment techniques with the aid of the iron-oxidizing bacteria, suitable for the mines in China, and develop techniques for recovering useful resources. The bio-aided waste water treatment process is a suitable method for treating waste water discharged from mining pits, in which ferrous iron present in waste water is oxidized with the aid of iron-oxidizing bacteria growing with ferrous ion as the energy source into ferric iron, which is precipitated at a low pH and removed in the presence of inexpensive calcium carbonate as the neutralizer. The pilot plant has been operating smoothly in a mode to treat waste water discharged from mining pits in Wushan Mine, almost satisfying the targets of treated water properties, i.e., pH: 0.5 or less, Cu: less than 0.5, Zn: less than 2.0, Pb: less than 1.0, Cd: less than 0.1, As: less than 0.5, Mn: less than 2.0, and SS: less than 70, all in mg/L except for pH. (NEDO)

  17. On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

    Yago, K; Endo, H [Ship Research Inst., Tokyo (Japan)


    The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

  18. Measurement method of a motion of traveling vehicle via three-dimensional image processing system; Sanjigen gazo kaisekiho ni yoru sharyo undo no keisoku to sono bunseki ni tsuite

    Yamada, Y; Matsuura, Y [Osaka Sangyo University, Osaka (Japan)


    Motion of traveling vehicle was taken by VTR-cameras set on the test course, as well as it also was measured by conventional measurement methods using sensors and devices installed in the vehicle. lotion pictures of the VTR were analyzed using three-dimensional image processing system (Peak lotus system). As a result, this system was especially effective for the measurement of traveling traces of the actual vehicle and the results were good agreement with the data obtained by conventional measurement methods. 2 refs., 8 figs.

  19. FY1998 report on a survey related to joint utilization of welfare device development data using an international network; 1998 nendo kokusai network ni yoru fukushi kiki kaihatsu data no kyodo riyo ni kansuru chosa hokokusho



    A survey was made in relation with joint utilization of welfare device development data using an international network. Developing welfare devices requires data from ergonomic and medical systems, while the cope of the objects is wide, and the kinds are various. For proliferation of welfare devices, system compatibility evaluation including that on using environment is important, including living environments that are different by countries. The present survey has identified how data for aged, handicapped and help-needing persons are accumulated and utilized in research organizations in America and Europe for both of the ergonomic and medical areas. The survey also investigated major academic societies in overseas countries, and collected database and academic network information that support the advanced research and development. At the same time, investigations were also made on organizations and corporations who are moving forward the efficient data utilization. Welfare device and service information providing systems in Japan were investigated to compare them with the trends in other countries. Conceptions and methods were compiled to utilize data internationally and jointly. Database models for device development were considered, and a proposal was made on structuring a research and development supporting database, and the operation method thereof. (NEDO)

  20. Annual cycle solar energy utilization with seasonal storage. Part 8. Study on periodic steady state of the annual cycle energy system at a practical operation; Kisetsukan chikunetsu ni yoru nenkan cycle taiyo energy riyo system ni kansuru kenkyu. 8

    Tanaka, H; Okumiya, M [Nagoya University, Nagoya (Japan)


    A study was made of the periodic steady state of the annual cycle solar energy system with seasonal heat storage at a practical operation. Cold heat in winter and warm heat in summer are stored in the seasonal storage tank, and these are each used in shift until when demand for cold/warm heat appears. Moreover, gap in quantity of cold/warm heat going in/out of the heat storage tank during a year is filled by natural energy such as solar energy, so that the system can be operated in annual cycles. Studies were conducted of the periodic unsteady term and the problem on lowering of performance during the term such as the periodic unsteady term of water temperature inside the seasonal heat storage tank and temperature of the soil around the storage tank, and the level of lowering of performance during the term, necessity of additional operation/control at the start of operation and aged deterioration of the system. Within the assumption, even if starting operation in any time of the year, the system could show the performance almost expected from the first operation year with no additional system operation and control required only at the start of operation. It is thought that the heat source selection control of heat pump largely contributes to this. 4 refs., 5 figs., 3 tabs.

  1. Computation accuracy of flow conditions around a very large floating structure using a multi-layer model. Comparison with experimental results; Taso model ni yoru choogata futai mawari no ryukyo keisan seido ni tsuite. Jikken tono hikaku

    Kyotsuka, Y [Kyushu University, Fukuoka (Japan); Omori, H; Nakagawa, H; Kobayashi, M [Mitsui Engineering and Shipbuilding Co. Ltd., Tokyo (Japan)


    As one of the environmental problems in sea areas surrounding a very large floating structure (VLFS), change in flow condition is important, and it is one of the factors dominating the prediction of succeeding diffusion and ecosystems. Although a multi-layer model is in wide use for computation of flow condition and diffusion in one inner bay, its applicability should be reexamined because of no consideration of VLFSs. In this study, flow velocity profiles around a barge were then measured through the towing test of a barge in shallow water, and compared with computation results using a multi-layer model. The multi-layer model computed the flow velocity profiles by dividing the flow region to be computed into normal one and that under VLFS, and determined pressures under VLFS by 2-D Poisson`s equation. Slip condition was used as boundary condition at the bottom considering the number of layers under VLFS. Further numerical computation was conducted by 2-D MAC method, in particular, to compare flow around the wake of VLFS with experimental one. Both computation results well agreed with experimental one. 3 refs., 9 figs., 1 tab.

  2. Electromagnetic survey (TEM method) in Teradomari and examination of resistivity structure to be based on near surface information; Niigataken Teradomarimachi ni okeru denji tansa kekka (TEM ho) no doshitsu joho ni yoru kento

    Ishikawa, H; Mitsuhata, Y; Matsuo, K; Tanaka, H [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Wada, K [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)


    TEM method was applied to estimate soil structure from resistivity change of underground water saturated stratum featured by slow S wave and fast P wave over 1500m/s. Vertical magnetic field was measured by underlaying a transmission loop of 60m{times}60m around a measuring point in Teradomari, Niigata prefecture, and by installing a magnetic sensor at the measuring point. From comparison of a soil profile with the resistivity profile obtained by TEM data, the former well consisted with the latter. The surface low resistivity stratum corresponded to alluvium from comparison of it with soil and logging data. This alluvium base with fast P wave over 1500m/s satisfied the condition of optimum blasting depth because of a saturated stratum in the surface base. The resistivity structure was related to a saturated stratum. Sand bed was thick at the interface between alluvium low ground and hill area, and from the analytical result, the depth of sand bed showing high resistivity was more shallow than that of the alluvium base, pointing out necessary notice in interpretation. Resistivity survey is promising as simple method for optimum blasting depth. 4 refs., 6 figs., 1 tab.

  3. Engineering characteristics of the improved soil by deep mixing method using coal ash; Sekitanbai wo riyoshita FGC shinso kongo shori koho ni yoru kairyodo no kogakuteki seishitsu to kongo no tenbo ni tsuite

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Azuma, K; Watanabe, M [Electric Power Development Co. Ltd., Tokyo (Japan)


    Japan currently produces about six million tons of coal ash annually, whose effective bulk utilization to earth engineering materials is an important issue of technological development. A slurry may be made by mixing the following three kinds of materials: fly ash discharged from power plants exclusively burning dust coal (F), gypsum generated as a by-product in a stack gas desulfurizing process (G), and commercially available cement (C). The slurry would be called an FGC slurry taking the first letters of the materials. This paper presents the results of laboratory tests, in-situ execution tests and centrifuge model testing on engineering characteristics of soils improved by the FGC slurry when the slurry is applied to implementing the deep mixing method. As a result, a large number of findings were obtained including the following matters: the FGC deep mixing method makes it possible to improve ground beds having small deformation coefficient with the same accuracy as in the cement-based deep mixing (CDM) method at strengths lower than 5 kg/cm {sup 2} which is difficult with the CDM method, not to speak of strengths equivalent to that is possible with the normal CDM method; and development of a ground bed with improved strength is possible without being governed by quality and kinds of the fly ash. 1 ref., 23 figs., 5 tabs.

  4. Model experiment on change of seismic properties of a fracture caused by injecting/draining water; Chusui/haisui ni yoru kison kiretsu no dansei denpa tokusei no henka ni kansuru model jikken

    Watanabe, T; Koizumi, T; Sassa, K [Kyoto University, Kyoto (Japan). Faculty of Engineering


    Effect of water injection/draining on elastic waves penetrating through cracks is examined by measuring elastic waves before, during, and after the injection/draining of water into/from cracks in presence in granite. Two blocks of rock, with their crack-containing surfaces in contact with each other, are placed in a vessel, and water injection/draining is done through a hole on a vessel bottom side so that water will penetrate into the cracks. When the blocks are dry, there is almost no contact between the cracks, and so no crack penetrating waves are observed. Crack penetrating waves are produced when water is injected, and the position of the receiver sensing the penetrating waves changes as the water level rises. When the water level is lowered from the high water level, the waveform changes again as the level changes. The change in waveform is not so remarkable, however, as that observed during water injection thanks to the water residual in the cracks. It is now inferred that crack investigation is more effective when it is carried out with water being injected into dry cracks. The difference produced between the dry state and wet state when water is injected into dry cracks is used to detect the presence of cracks in this experiment, and this may be applied also to the investigation of cracks in the shallow part of the ground. 4 refs., 11 figs.

  5. Ab initio MO study on the thermal stability of 1-phenyl-1H-tetrazoles; Hikeikenteki bunshi kidoho ni yoru 1-Ph-1H tetorazoru yudotai no netsu anteisei hyoka ni kansuru kenkyu

    Ono, Yoshio.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering; Matsunaga, Takehiro. [National Institute of Materials and Chemical Research, Tsukuba (Japan)


    Ab initio MO calculations of 1-phenyl-1H-tetrazoles were carried out, in order to explain a substituent effects on its high thermal stability and to estimate the thermal stability of the other tetrazoles. Similar to 1H-tetrazole, five bonds in the tetrazole ring have intermediate lengths between single and double bond lengths. Phenyl and tetrazole rings are not both on one plane showing no interaction. Three indexes addopted as a measure of thermal stability indicate that the more equal the bond lengths of the ring are and that the bigger the stabilization energy by ring formation is, the more thermally stable they are. It is found out that there is the relationship between the thermal stability and the ring charge. That is, the more negative the ring charge is, the more thrmally stable the tetrazole is. Also, there is a good relationship between the thermal stability and the energy level of orbital of which orbital is an anti bonding type with respect to the N3-N4 bond. The higher the energy level is, the more thermally stable the tetrazole is. (author)

  6. Enhancement of condensation heat transfer using electric field. Effects of wire-electrode coating; Denba ni yoru gyoshuku netsu dentatsu no sokushin ni kansuru kenkyu. Wire denkyoku no hifuku koka

    Chu, R. [Gifu University, Gifu (Japan). Faculty of Enginering; Nishio, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Tanasawa, I. [Nihon University, Fukushima (Japan). College of Engineering


    In the present paper, an attempt is made to develop an effective EHD enhancement technique for condensation heat transfer of steam around a horizontal finned tube. The main idea in the present study is to reduce the power consumption by using a partially coated electrode, and the experimental data of heat transfer coefficients and flooding angles are presented. The result indicates that, by using such an electrode, the enhancement ratio keeps almost the same level with that of a bare electrode but the power consumption can be markedly decreased. Within the present experimental range, the condensation heat transfer coefficient on the finned tube with the partially coated electrode reaches a value about 3 times larger than that without electrode. In addition, a model in presented for the EHD effect on the flooding angle and it is confirmed that the prediction from the model is in good agreement with the experimental data. (author)

  7. On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

    Yago, K.; Endo, H. [Ship Research Inst., Tokyo (Japan)


    The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

  8. Improved paper quality and runability by biological process water recovery in closed water circuits of recycle mills; Saisei banshi kojo ni okeru junkansui no seibutsugakuteki shori ni yoru shihinshitsu oyobi sogyosei no kaizen

    Habets, L.; Knelissen, H.; Hooimeijer, A.; Nihei, K. [Nippon Paper Industries Co. Ltd., Tokyo (Japan)


    A lot of efforts have been made traditionally for reducing the amount of water consumption in recycled paper industry. Several mills in Europe and the North America have succeeded in running the closed white water circuit that means to make the amount of water discharge be zero by returning the effluent water back. In this paper, the relevant factors that contaminate the white water in recycled paper mills are investigated. The accumulation of substances which provide bad effects on the paper manufacturing process and product quality is caused by the closed white water circuit in the recycled paper mills. The accumulated substances in white water include microorganisms, volatile fatty acids, salts, calcium, etc. Anaerobic/aerobic treatment is used as means for reducing the consumption of chemicals and energy and minimizing residues. The first biological in line treatment plant was utilized by Zulpich Papier in Germany and its result is satisfactory in aspects of production and product quality. 5 refs., 6 figs., 2 tabs.

  9. Fiscal 1999 research result report. Research on improvement of boiling heat transfer characteristics by photocatalyst wall; 1999 nendo hikari shokubai hekimen ni yoru futto netsu dentatsu tokusei kaizen ni kansuru kenkyu chosa hokokusho



    Research was made on improvement of the wettability and boiling heat transfer characteristics of a photocatalyst wall. Measurement experiment of the wettability was made for anatase type titan oxide-coated Al, SUS and Pb plates, rutil type titan oxide-flame coated SUS plate, raw plate, and oxide-plasma coated titan plate. In the ground experiment, the contact angles of distilled water and oil on specimen surfaces were measured. In the microgravity experiment, falling droplet images were recorded by using the facility of Japan Microgravity Center (JAMIC). For obtaining the effect of radioactive emission, UV irradiation, {gamma} ray and neutron beam irradiation by nuclear reactor, and {gamma} ray irradiation by Co-60 were carried out. As the experiment result, the rutil type titan oxide-flame coated SUS plate, nonconductor-coated titan plate, and zircaloy plate showed large improvement of the wettability by {gamma} ray irradiation with Co-60. It was also confirmed that in particular, titan shows the large effect of radioactive emission, and the wettability deteriorates rapidly after {gamma} ray irradiation. (NEDO)

  10. Fiscal 1997 survey report on the project on energy conservation by effectively using building energy in Indonesia; 1997 nendo chosa hokokusho (Indonesia ni okeru biru energy yuko riyo ni yoru sho energy ka project chosa)



    As an energy conservation method for a model building, the following eight methods were selected and trially calculated of the effects. 1) adoption of high efficient illumination apparatus, 2) introduction of an illuminance control system, 3) cooling water secondary pump with invertor, 4) ventilation control for parking lots, 5) heightening of the established temperature, 6) improvement of the 24-hour run chiller, 7) elevator with invertor, and 8) introduction of the photovoltaic power generation. As a result, it was found out that energy was totally reduced by about 3,837.4 MWh/yr or 25.6%. If viewed from the amount of reduction in greenhouse gas, the amount of CO2 emitted from office buildings, approximately 0.22 million t-C/yr, decreases to approximately 0.16 million t-C/yr. Further, approximately 0.93 million t-C/yr, the amount of CO2 emitted from commercial use facilities such as office buildings, department stores and hotels is reduced to about 0.69 million t-C/yr, thanks to the effect of the project on energy saving buildings, which made a CO2 reduction by approximately 0.24 million t-C/yr possible. Validity of the project on energy conservation in Indonesia was confirmed. 2 refs., 55 figs., 38 tabs.

  11. Adaptability of drowsiness level detection that measures blinks utilizing image processing to changes in the ambient light; Hikari kankyo no henka ni tekiosuru kao gazo shori ni yoru inemuri unten kenchi

    Kaneda, M; Obara, H; Nasu, T [Nissan Motor Co. Ltd, Tokyo (Japan)


    A drowsiness warning system that measures blinks utilizing image processing technology has a number of issues that need to be resolved. One issue is the adaptability of the system to changes in the ambient light environment in the actual vehicle interior. We have devised image processing software which is robust to changes in the ambient light. The drowsiness detection performance of the system was evaluated in laboratory tests and actual driving tests. It was found that the system can has a positive effect on detecting drowsiness level. 3 refs., 10 figs.

  12. Achievement report on research and development (1st phase) of direct iron making by use of high-temperature; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho



    Efforts are put into the study of direct iron making for use in a closed system where heat energy from a multi-purpose high-temperature gas furnace expected to be developed in the near future will be utilized for iron making. The researches, carried out for the establishment of technologies necessary for designing, building, and operating a pilot plant dimensionally suitable for connection to a 50MWt multi-purpose high-temperature gas furnace, cover the plant total system, a high-temperature heat exchanger, ultrahigh-temperature alloys, high-temperature insulating materials, a reduced gas generating unit, and a reduced iron making unit. When the effort is evaluated as a whole, it is found that the newly developed system is effective in preventing pollution, emitting but 0.1Nm{sup 3} of SOx per 1 ton of crude iron against the 0.4-0.9Nm{sup 3} emitted by a blast furnace/converter iron making mill. It is also found effective in reducing fossil fuel dependence and in enhancing energy source diversification. When it comes to energy conversion efficiency, furthermore, it is shown that the new system achieves a rate of 60% or more while only approximately 30% is attained by light water reactor power generation and approximately 40% by a high-temperature gas furnace. (NEDO)

  13. Borehole geophysics for delineating the geological structure in the Sakonishi prospect, the Hida area, Japan; Hida chiiki Sako nishi chiku ni okeru boring ko riyo butsuri tansa ni yoru chishitsu kozo kaiseki

    Katayama, H.; Hishida, H.; Yoshioka, K. [Metal Mining Agency of Japan, Tokyo (Japan)


    In order to discuss effectiveness of physical exploration in the Sakonishi prospect in the Hida area, physical exploration was carried out by utilizing bored wells. This area contains the Kamioka mine, one of the major base metal mines in Japan, where electrical exploration has been attempted several times in the past. No effective results have been obtained, however, because specific resistance contrast between mine beds and base rocks is too small, and the topography is too steep making site workability inferior. As part of the investigations on geological structures over wide areas, electrical logging (specific resistance and natural potential) was performed in fiscal 1995 and 1996 by utilizing the boreholes. Induced polarization logging was also conducted on the same boreholes. A traverse line on the ground with a length of 600 m and boreholes were used to execute specific resistance tomography. Clear extraction was possible on a fault structure which is thought related with limestone distribution and mine bed creation. However, it was not possible to identify upward continuity of zinc ores expected in the exploration. Because of not large a specific resistance contrast between zinc ores and base rocks, it is difficult to find mine bed locations only from the information on the specific resistance. 5 refs., 5 figs., 1 tab.

  14. FY 1997 report on the modification of dental materials with Ag for improvement of antibacterial activity; 1997 nendo chosa hokokusho (gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu)



    Improvement of an antibacterial activity is one of the issues in modification of artificial teeth for an aged society. Study was made on improvement technique of an antibacterial activity with Ag ion as secondary corrosion measures. Partial gaps of dental materials themselves and gaps between materials and peripheral tissues causes bad breath or bad teeth through propagation of disease germs. Ag ion is harmless and has an antibacterial activity for bio-tissues from a macro-viewpoint, however, only corrosion germ causing bad teeth in mouths should be sterilized by controlling an elution rate of Ag properly. The antibacterial activity was controlled by controlling Ag ion implantation depth and rate, and Ag elution rate for dental materials. Experiment was made on an IMZ twinplus specimen implanted with Ag ion and an Ag thin film-coated specimen using beagle dog in comparison with an unmodified specimen. As a result, the very favorable antibacterial activity was obtained. Ag ion is effective for prevention of endogenous infectious disease due to mouth germs in dental surgery. 3 refs., 47 figs., 10 tabs.

  15. Outline of investigation on restraint of carbon dioxide generation by green chemistry. 1999.1-1999.3; 1998 nendo green chemistry ni yoru CO2 hassei yokusei ni kakawaru chosa kenkyu chosa hokokusho



    Investigations were conducted into the above in some leading OECD (Organization for Economic Cooperation and Development) member states. Green chemistry is a new concept in which clean technology, environment-friendly chemistry, and the like are combined, and is a chemical solution for reducing or stopping the use or generation of materials, products, by-products, solvents, reagents, etc., which are dangerous to health and environments, throughout the whole life cycle of chemicals covering the processes of their designing, manufacturing, dumping, and recycling. In this fiscal year, the actual state of the generation of biomass, regarded as representative of reproducible materials, and its feasibility as chemical resources were investigated. In an effort at finding out chemical reactions safer to health and causing less environmental impact, investigations were also conducted into the recent trends of catalysts, novel reactions for organic syntheses, use of supercritical fluids, photocatalysts, biomimetic processes, etc. The development of substitutes for plastic additives was also studied. Since acceptance by the citizenry is quite important for green chemistry to take effect, educating and enlightening activities in the U.S., Britain, France, and Germany were inquired into. (NEDO)

  16. Result of comparative experiment on environmental comfort in room using hot heat environment testing unit. Onnetsu kankyo shiken unit ni yoru shitsunai kankyo no kaitekisa no hikaku jikken kekka ni tsuite

    Fujiwara, T; Kawashima, K [The Hokkaido Electric Power Co. Inc., Sapporo (Japan)


    Measurements were carried out on three buildings having different heat insulation, airtightness and heat capacity for testing the hot heast enviroments (having a room size of about 4.6 m{times}3.7m{times}2.3 m) as to the temperature differences between the upper and lower parts of the room and the MRT (mean radiation temperature, representing the temperature of radiation from the wall face). These are compared according to types of heating appliance. The result is summarize as follows: The temperature difference in the upper and lower parts is affected largely by the airtightness of the building, the difference being capable of getting reduced by rasing the airtightness even in a buildings low in heat insulation. In a building with low airtightness, type of heating appliance and its installation location affect the temperature difference. The MRT is determined determined nearly completely by the heat insulation of the wall face in a room, but it tends to be affected easily by the specification and area of windows. A floor heating system increases the MRT and generates very little difference in temperatures in the upper and lower parts of the room. A comparison using a PMV (one of the indexes for enviromental comfort in a room) was also conducted. 12 figs., 7tabs.

  17. Effects of diesel fuel additives on engine performance and reliability. Part 2. Effects of lubricity additives; Keiyu tenkazai ga engine seino oyobi shinraisei ni ataeru eikyo. 2. Junkatsusei kojo ni yoru eikyo

    Matsudaira, J; Okada, M; Naruse, H [Toyota Motor Corp., Aichi (Japan)


    Many studies about the effects of lublicity additives for diesel fuel have been carried out and reported. These additives have already been used in Europe, north-America for couple of years and it has just started in Japanese market this July. This paper mainly describes the effects of lublicity additives on engine performance and reliability. At first, the effects on engine reliability were investigated during 30 thousand kms chasis dynamometer test. Secondary, the effects on piston ring corrosion, injection nozzle fouling and water separation were investigated. Furthermore, 70 thousand kms engine reliability test was conducted, and investigated some component parts. 2 refs., 10 figs., 4 tabs.

  18. Study on utilization of shallow sea area by building an alga field. Discussions on its utilization for cultivating Ulvales; Sojo zosei ni yoru senkaiiki riyo no kenkyu. Anaaosa no baiyo to sono riyo ni kansuru kento

    Tsuno, M.; Maebayashi, M. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)


    Discussions were given on mass cultivation in a water tank using sea water of an alga Ulvales used as feed for sea urchins and abalone. A fertilizer composed of ammonium sulfate and superphosphate of lime was used, and a water temperature was set as the environmental condition. Two kinds of Ulvales produced in different areas were used. One of the two kinds had full growth periodical and weight increasing rate low, but the other Ulvales had high weight increasing rate and no blights in alga bodies, and was found suitable for mass production. The result of a test on stocks of the latter species may be described as follows: multiple regression formulas for harvest, water temperature and illumination intensity were introduced for each cultivating condition for four cases regarding accommodation density and harvest frequency; and if a cultivating condition by which the harvest is maximized is adopted, a one cubic meter water tank placed on a place with good sunlight may be expected of producing as much harvest as 2181 grams at water temperature of 15{degree}C and 4899 grams at 25{degree}C. The cultivation requires the following precautions: aeration is required; sea water should be introduced into the tank; a mixed fertilizer with ratio of ammonium sulfate at 100 to superphosphate of lime at 15 may be used; water temperatures suitable for mass cultivation are 13 to 15{degree}C or higher; and light must be irradiated evenly. 14 refs., 9 figs., 5 tabs.

  19. Reduction mechanism of Ni2+ into Ni nanoparticles prepared from ...

    journal of. March 2009 physics pp. 577–586. Reduction mechanism of Ni2+ into Ni ..... and at high field, no domain wall is available and hence, the system becomes a .... [23] J Ding, T Tsuzuki, P G McCormick and R Street, J. Phys. D: Appl.

  20. Reactive Ni/Ti nanolaminates

    Adams, D. P.; Bai, M. M.; Rodriguez, M. A.; McDonald, J. P.; Jones, E. Jr.; Brewer, L.; Moore, J. J.


    Nickel/titanium nanolaminates fabricated by sputter deposition exhibited rapid, high-temperature synthesis. When heated locally, self-sustained reactions were produced in freestanding Ni/Ti multilayer foils characterized by average propagation speeds between ∼0.1 and 1.4 m/s. The speed of a propagating reaction front was affected by total foil thickness and bilayer thickness (layer periodicity). In contrast to previous work with compacted Ni-Ti powders, no preheating of Ni/Ti foils was required to maintain self-propagating reactions. High-temperature synthesis was also stimulated by rapid global heating demonstrating low ignition temperatures (T ig )∼300-400 deg. C for nanolaminates. Ignition temperature was influenced by bilayer thickness with more coarse laminate designs exhibiting increased T ig . Foils reacted in a vacuum apparatus developed either as single-phase B2 cubic NiTi (austenite) or as a mixed-phase structure that was composed of monoclinic B19 ' NiTi (martensite), hexagonal NiTi 2 , and B2 NiTi. Single-phase, cubic B2 NiTi generally formed when the initial bilayer thickness was made small.

  1. Electroplated Ni on the PN Junction Semiconductor

    Kim, Jin Joo; Uhm, Young Rang; Son, Kwang Jae; Kim, Jong Bum; Choi, Sang Moo; Park, Jong Han; Hong, Jintae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    Nickel (Ni) electroplating was implemented by using a metal Ni powder in order to establish a Ni-63 plating condition on the PN junction semiconductor needed for production of betavoltaic battery. PN junction semiconductors with a Ni seed layer of 500 and 1000 A were coated with Ni at current density from 10 to 50 mA cm{sup 2}. The surface roughness and average grain size of Ni deposits were investigated by XRD and SEM techniques. The roughness of Ni deposit was increased as the current density was increased, and decreased as the thickness of Ni seed layer was increased.

  2. Electroplated Ni on the PN Junction Semiconductor

    Kim, Jin Joo; Uhm, Young Rang; Son, Kwang Jae; Kim, Jong Bum; Choi, Sang Moo; Park, Jong Han; Hong, Jintae


    Nickel (Ni) electroplating was implemented by using a metal Ni powder in order to establish a Ni-63 plating condition on the PN junction semiconductor needed for production of betavoltaic battery. PN junction semiconductors with a Ni seed layer of 500 and 1000 A were coated with Ni at current density from 10 to 50 mA cm 2 . The surface roughness and average grain size of Ni deposits were investigated by XRD and SEM techniques. The roughness of Ni deposit was increased as the current density was increased, and decreased as the thickness of Ni seed layer was increased

  3. Synthesis and electrochemical behavior of nanostructured cauliflower-shape Co-Ni/Co-Ni oxides composites

    Gupta, Vinay; Kawaguchi, Toshikazu; Miura, Norio


    Nanostructured Co-Ni/Co-Ni oxides were electrochemically deposited onto stainless steel electrode by electrochemical method and characterized for their structural and supercapacitive properties. The SEM images indicated that the obtained Co-Ni/Co-Ni oxides had cauliflower-type nanostructure. The X-ray diffraction pattern showed the formation of Co 3 O 4 , NiO, Co and Ni. The EDX elemental mapping images indicated that Ni, Co and O are distributed uniformly. The deposited Co-Ni/Co-Ni oxides showed good supercapacitive characteristics with a specific capacitance of 331 F/g at 1 mA/cm 2 current density in 1 M KOH electrolyte. A mechanism of the formation of cauliflower-shape Co-Ni/Co-Ni oxides was proposed. A variety of promising applications in the fields such as energy storage devices and sensors can be envisioned from Co-Ni/Co-Ni oxides

  4. Radiochemical method for 63Ni

    Holm, E.; Nilsson, U.; Hallstadius, L.


    A radianalytical method for the determination of 63 Ni content in environmental samples of activated corrosion products is described. After chemical separation and electrodepositing of 63 Ni on silver briquets, the chemical yield is determined by X-ray fluorescence analysis. For the detection of low-energy beta activity, an open gas flow GM-counter with an anticoincidence guard counter is put to use

  5. Electronic structure of Ni/sub 3/Al and Ni/sub 3/Ga alloys

    Pong, W F; Chang, Y K; Tsai, M H; Hsieh, H H; Pieh, J Y; Tseng, P K; Lee, J F; Hsu, L S


    This work investigates the charge transfer and Al(Ga) p-Ni d hybridization effects in the intermetallic Ni/sub 3/Al(Ni/sub 3/Ga) alloy using the NiL/sub 3.2/- and K-edge and Al(Ga)K X-ray absorption near edge structure (XANES) measurements. We find that the intensity of white-line features at the NiL/sub 3.2/-edge in the Ni/sub 3/Al(Ni /sub 3/Ga) alloy decreased in comparison with that of pure Ni, which can be attributed to the enhancement of Ni3d states filling and the depletion of the density of Ni 3d unoccupied states in the Ni/sub 3 /Al(Ni/sub 3/Ga) alloy. Two clear features are also observed in the Ni/sub 3/Al(Ni/sub 3/Ga) XANES spectrum at the Al(Ga) K-edge, which can be assigned to the Al(Ga) unoccupied 3p (4p) states and their hybridized states with the Ni 3d/4sp states above the Fermi level in Ni/sub 3/Al(Ni/sub 3/Ga). The threshold at Al K-edge XANES for Ni/sub 3/Al clearly shifts towards higher photon energies relative to that of pure Al, indicating that Al loses charges upon forming Ni/sub 3 /Al. ...

  6. Nitriding behavior of Ni and Ni-based binary alloys

    Fonovic, Matej


    Gaseous nitriding is a prominent thermochemical surface treatment process which can improve various properties of metallic materials such as mechanical, tribological and/or corrosion properties. This process is predominantly performed by applying NH{sub 3}+H{sub 2} containing gas atmospheres serving as the nitrogen donating medium at temperatures between 673 K and 873 K (400 C and 600 C). NH{sub 3} decomposes at the surface of the metallic specimen and nitrogen diffuses into the surface adjacent region of the specimen whereas hydrogen remains in the gas atmosphere. One of the most important parameters characterizing a gaseous nitriding process is the so-called nitriding potential (r{sub N}) which determines the chemical potential of nitrogen provided by the gas phase. The nitriding potential is defined as r{sub N} = p{sub NH{sub 3}}/p{sub H{sub 2}{sup 3/2}} where p{sub NH{sub 3}} and p{sub H{sub 2}} are the partial pressures of the NH{sub 3} and H{sub 2} in the nitriding atmosphere. In contrast with nitriding of α-Fe where the nitriding potential is usually in the range between 0.01 and 1 atm{sup -1/2}, nitriding of Ni and Ni-based alloys requires employing nitriding potentials higher than 100 atm{sup -1/2} and even up to ∞ (nitriding in pure NH{sub 3} atmosphere). This behavior is compatible with decreased thermodynamic stability of the 3d-metal nitrides with increasing atomic number. Depending on the nitriding conditions (temperature, nitriding potential and treatment time), different phases are formed at the surface of the Ni-based alloys. By applying very high nitriding potential, formation of hexagonal Ni{sub 3}N at the surface of the specimen (known as external nitriding) leads to the development of a compound layer, which may improve tribological properties. Underneath the Ni{sub 3}N compound layer, two possibilities exist: (i) alloying element precipitation within the nitrided zone (known as internal nitriding) and/or (ii) development of metastable and

  7. Ni4Ti3 precipitate structures in Ni-rich NiTi shape memory alloys

    Holec, D.; Bojda, O.; Dlouhy, A.


    Non-uniform distributions of Ni 4 Ti 3 precipitate crystallographic variants are investigated in a Ni-rich NiTi shape memory alloy after aging, assisted by external stress. A finite-element method model is presented that considers the elastic anisotropy of the B2 parent phase and also mutual misorientations of grains in a polycrystalline sample. On loading by the external stress, the stress is redistributed in the microstructure and the precipitation of some Ni 4 Ti 3 crystallographic variants becomes distinctly favorable in grain boundary regions since these variant configurations minimize the elastic interaction energy. The volume fraction of the affected grain boundary regions is calculated and the numerical results are compared with the data obtained by differential scanning calorimetry and transmission electron microscopy

  8. Ni4Ti3 precipitate structures in Ni-rich NiTi shape memory alloys

    Holec, David; Bojda, Ondřej; Dlouhý, Antonín


    Roč. 481, Sp. Iss. (2008), s. 462-465 ISSN 0921-5093. [ESOMAT 2006. Bochum, 10.09.2006-15.09.2006] R&D Projects: GA ČR(CZ) GA106/05/0918 Institutional research plan: CEZ:AV0Z20410507 Keywords : NiTi shape memory alloys * Ni4Ti3 precipitates * Multi-step martensitic transformations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.806, year: 2008

  9. Electronic structure of Ni-- and Ni2--ethylene cluster complexes

    Basch, H.; Newton, M.D.; Moskowitz, J.W.


    The electronic structure of metal cluster--ethylene complexes has been investigated by carrying out ab initio bonding pair-correlated, self-consistent field, and configuration interaction (CI) calculations on the NiC 2 H 4 and Ni 2 C 2 H 4 species. The π-NiC 2 H 4 and π-Ni 2 C 2 H 4 cluster complexes are found to be bound, the former only with CI, while disigma-Ni 2 C 2 H 4 has only a repulsive Ni 2 --C 2 H 4 ground state potential curve. The bonding in the π-type cluster complexes can be described as follows: The metal atom configuration is 3d 9 4s 1 with the 4s hybridized (by the metal 4p) away from the ethylene molecule, thereby allowing the π orbital to form a dative sigma bond with the metal atom. The bonding interaction is promoted by the presence of a second nickel atom behind the first one, leading to a 4s orbital electron deficiency of the bonded nickel atom and thus making this nickel atom a better electron acceptor. Back donation from the occupied metal 3d into the ethylene π* molecular orbital also takes place to some extent, and thus both features of the classical Dewar--Chatt--Duncanson model are observed. The π-Ni 2 C 2 H 4 species is analyzed in terms of the addition of a bare nickel atom to a π-NiC 2 H 4 cluster complex, with concomitant stabilization of the orbitals of the bonded nickel atom. A study of the excited electronic states of π-NiC 2 H 4 shows that low-lying 4s→π* and 3d→π* (M→L) charge transfer transitions are predicted. The former is not observed experimentally, probably due to the diffuse nature of the 4s orbital. The relationship between small cluster--ethylene complex systems and ethylene chemisorption on a nickel metal surface is discussed

  10. Radioactive 63Ni in biological research

    Kasprzak, K.S.; Sunderman, F.W. Jr.


    Applications of 63 Ni in biological research are reviewed, with emphasis upon recent investigations of nickel metabolism and toxicology in experimental animals. The radiochemistry of 63 Ni is summarized, including consideration of the preparation of certain 63 Ni compounds (e.g. 63 Ni(CO) 4 and 63 Ni 3 S 2 ) that are of current interest in toxicology, teratology and cancer research. Practical guidance is given regarding the detection and determination of 63 Ni in biological materials by autoradiography and liquid scintillation spectrometry. (author)

  11. Superstructure of NiAs

    Nozue, Tatsuhiro; Kobayashi, Hisao; Kamimura, Takashi; Yamaguchi, Yasuo


    The structural transition in NiAs was studied by neutron diffraction on the single crystalline sample. The crystal structure of NiAs has been reported to be bottom-centered orthorhombic with Cmc2 1 symmetry (niccolite-type). The measurement of temperature dependence of the powder X-ray diffraction revealed that NiAs undergoes a structural transition to the NiAs-type at T t =335 K. In present neutron diffraction experiment at room temperature, we observed the reflections indexed on the basis of the orthorhombic unit cell. The intensities of these reflections are qualitatively explained in terms of the niccolite-type structure with taking account of three domain structures, except for the weak reflections indexed as (001), (003) and (012). Then, the intensities of (001), (002) and (004) reflections were measured in temperature range of 20 to 420 K. The temperature dependences of (002) and (004) reflections qualitatively agree with those of the calculated intensities using the atomic positions of niccolite-type structure. However, the temperature dependence of (001) reflection shows the anomaly around T t , which suggests the symmetry of crystal structure of NiAs is not the Cmc2 1 symmetry. (author)

  12. Thermal stability and electrical characteristics of NiSi films with electroplated Ni(W) alloy

    Xin Yuhang; Hu Anmin; Li Ming; Mao Dali


    In this study, an electroplating method to deposited Ni, crystalline NiW(c-NiW), amorphous NiW (a-NiW) films on P-type Si(1 0 0) were used to form Ni-silicide (NiSi) films. After annealed at various temperatures, sheet resistance of Ni/Cu, c-NiW/Cu and a-NiW/Cu was measured to observe the performance of those diffusion barrier layers. With W added in the barrier layer, the barrier performance was improved. The results of XRD and resistance measurement of the stacked Si/Ni(W)/Cu films reveal that Cu atom could diffuse through Ni barrier layer at 450 deg. C, could diffuse through c-NiW at 550 deg. C, but could hardly diffuse through a-NiW barrier layer. c-NiW layer has a better barrier performance than Ni layer, meanwhile the resistance is lower than a-NiW layer.

  13. Achievement report for fiscal 1999. Research on mesh-based estimation of natural energy for Southeast Asia as represented by Myanmar (Assessment of wind power and solar energy using numerical weather model); 1999 nendo Myanmar koku wo rei ni shita Tonan Asia ni okeru shizen energy no mesh suitei ni kansuru kenkyu seika hokokusho. Suchi kisho model ni yoru furyoku taiyo energy hyoka



    As the first step for the introduction of wind power systems and photovoltaic power systems into developing countries in Southeast Asia etc. and for their diffusion in them for the exploitation of natural energy, a numerical weather model useable in Southeast Asia is developed to make up for the insufficiency of weather data in the region. A technique is developed, to explain which the case of Myanmar is cited, for estimating with accuracy such natural conditions as wind direction, wind velocity, and solar radiation in the past one-year period for the assessment of power to be generated using wind turbines and solar panels. The results of the observation of wind conditions indicate that wind directions are mainly northerly or westerly and that wind speeds are as week as 1-3m/s on the average. As for total solar radiation per diem in December through March, it is found that there is 17-23MJ/m{sup 2}/day, which is twice the level to be measured in Tokyo. A comparison is made between the weather observation results and a model calculation, and it is found that the latter sufficiently reproduces the actual weather conditions. Based on the values of wind conditions and solar radiation estimated in Myanmar, the amount of power to be obtained from an assumed arrangement of wind power systems and solar panels is assessed. (NEDO)

  14. Study on climate control of dwellings using underground air tunnel in the cold region. Part 1. Cooling performance of the underground air tunnel connected to a small-scaled test house; Kanreichi ni okeru chika air tunnel ni yoru junetsukankyo kaizen ni kansuru kenkyu. 1. Shokibo shiken kaoku ni okeru kaki no ryobo seino hyoka

    Miki, Y; Sanji, H; Ito, J; Komoda, T; Mitsuoka, K; Mogami, S [Kitami Institute of Technology, Hokkaido (Japan)


    Underground air tunnel is provided for cooling an experimentally built small house and the cooling performance is examined at Kitami Institute of Technology, Hokkaido. The house is provided with 120mm-thick layers of insulating material under the floor and inside the side walls and partitioning walls. The windows are equipped with blinds, with reed screens positioned outside to cover the windows. The air tunnel is a hard vinyl chloride tube, 200mm in internal diameter. It is buried 4.5m deep in the ground, and extends as long as 27m. A filter-provided 72W blower installed at the tunnel outlet is driven to force air through. As for the natural soil temperature in summer, it is found variable between 7.2 and 8.5degC. As the result of the experiment, it is found that thanks to the underground tunnel the room temperature is kept below 27degC even when the maximum temperature in the daytime is 30degC or higher provided the air flow is appropriately regulated. In this experiment, the maximum rate of instantaneously removed heat is approximately 2.5 times higher than the values in other previously reported experiments. The daily coefficient of performance is 6.5-11.1, again higher than the previously reported values. Different from application in warm regions, the effect of rise in the surrounding soil temperature on the cooling performance is not so conspicuous. 3 refs., 12 figs., 1 tab.

  15. Giant magnetoimpedance effect in sputtered single layered NiFe film and meander NiFe/Cu/NiFe film

    Chen, L.; Zhou, Y.; Lei, C.; Zhou, Z.M.; Ding, W.


    Giant magnetoimpedance (GMI) effect on NiFe thin film is very promising due to its application in developing the magnetic field sensors with highly sensitivity and low cost. In this paper, the single layered NiFe thin film and NiFe/Cu/NiFe thin film with a meander structure are prepared by the MEMS technology. The influences of sputtering parameters, film structure and conductor layer width on GMI effect in NiFe single layer and meander NiFe/Cu/NiFe film are investigated. Maximum of the GMI ratio in single layer and sandwich film is 5% and 64%, respectively. The results obtained are useful for developing the high-performance magnetic sensors based on NiFe thin film.

  16. High Ni in Archean tholeiites

    Arndt, Nicholas T.


    Archean tholeiites generally have higher Ni, Co. Cr and Fe than most younger tholeiites with similar MgO contents. These characteristics cannot be attributed to high T or P batch melting in the Archean mantle, because, although such melts are enriched in siderophile elements, they have higher MgO than normal tholeiites. As primary melts fractionate to lower MgO, they lose Ni, Co and Cr. Nor can the differences between Archean and younger tholeiites be attributed to secular variation in mantle compositions because Archean komatiites have Ni, Co, Cr contents similar to modern (Gorgona) komatiites. It is suggested that the high siderophile element content of Archean tholeiites results from mixing of either komatiitic with basaltic magmas, as might occur in an ascending, melting mantle plume or column, or of komatiite and more evolved rocks, as may take place when komatiite encounters and assimilates crustal rocks.

  17. Relation between shape of Ni-particles and Ni migration in Ni-YSZ electrodes – a hypothesis

    Mogensen, Mogens Bjerg; Hauch, Anne; Sun, Xiufu


    This is an attempt to explain a phenomenon of total depletion of Ni next to the electrolyte in Ni-YSZ cermet electrodes in solid oxide electrolysis cells during electrolysis at high current density/overpotential. Intuitively, we would think that Ni would always migrate down the steam partial...

  18. Ni-NiO core-shell inverse opal electrodes for supercapacitors.

    Kim, Jae-Hun; Kang, Soon Hyung; Zhu, Kai; Kim, Jin Young; Neale, Nathan R; Frank, Arthur J


    A general template-assisted electrochemical approach was used to synthesize three-dimensional ordered Ni core-NiO shell inverse opals (IOs) as electrodes for supercapacitors. The Ni-NiO IO electrodes displayed pseudo-capacitor behavior, good rate capability and cycling performance. © The Royal Society of Chemistry 2011



    We discuss the electronic state of Ni atoms in Ni metal and of Ni impurity in Cu and Au metals from the viewpoint of 3d configuration interaction (CI) using the Anderson impurity model including atomic multiplets. On the basis of the discussion, we give an interpretation for the Ni 2p-core X-ray

  20. Iodine capture by Hofmann-type clathrate Ni(II)(pz)[Ni(II)(CN)_4

    Massasso, Giovanni; Long, Jerome; Haines, Julien; Devautour-Vinot, Sabine; Maurin, Guillaume; Larionova, Joulia; Guerin, Christian; Guari, Yannick; Grandjean, Agnes; Onida, Barbara; Donnadieu, Bruno


    The thermally stable Hofmann-type clathrate framework Ni(II)(pz)[Ni(II)(CN)_4] (pz = pyrazine) was investigated for the efficient and reversible sorption of iodine (I_2) in the gaseous phase and in solution with a maximum adsorption capacity of 1 mol of I_2 per 1 mol of Ni(II)pz)[Ni(II)(CN)_4] in solution. (authors)

  1. Density functional theory study of the interfacial properties of Ni/Ni3Si eutectic alloy

    Zhao, Yuhong; Wen, Zhiqin; Hou, Hua; Guo, Wei; Han, Peide


    In order to clarify the heterogeneous nucleation potential of α-Ni grains on Ni 3 Si particles in Ni-Ni 3 Si eutectic alloy, the work of adhesion (W ad ), fracture toughness (G), interfacial energy (γ i ), and electronic structure of the index (0 0 1), (1 1 0) and (1 1 1) Ni/Ni 3 Si interfaces with two different cohesive manners are investigated using first-principles method based on density functional theory. Results indicate that the center site stacking sequence (OM) is preferable to continue the natural stacking sequence of bulk Ni and Ni 3 Si. Since OM stacking interfaces have larger W ad , G and γ i than that of the top site stacking (OT) interfaces. The Ni/Ni 3 Si (1 1 0) interface with OM stacking has the best mechanical properties. Therefore, the formation of this interface can improve the stability, ductility and fracture toughness of Ni-Ni 3 Si eutectic alloy. The calculated interfacial energy of Ni/Ni 3 Si (0 0 1), (1 1 0) and (1 1 1) interfaces with OM stacking proves the excellent nucleation potency of Ni 3 Si particles for α-Ni phase from thermodynamic considerations. Besides, the electronic structure and chemical bonding of (1 1 0) interface with OM stacking are also discussed.

  2. Density of Liquid Ni-Cr Alloy


    The density of liquid Ni-Cr alloy was measured by a modified sessile drop method. The density of liquid Ni-Cr alloywas found to decrease with increasing temperature and Cr concentration in the alloy. The molar volume of liquidNi-Cr alloy increases with increasing the Cr concentration in the alloy. The molar volume of Ni-Cr alloy determinedin the present work shows a positive deviation from the linear molar volume.

  3. Laser alloyed Al-Ni-Fe coatings

    Pityana, SL


    Full Text Available The aim of this work was to produce crack-free thin surface layers consisting of binary (Al-Ni, Al-Fe) and ternary (Al-Ni-Fe) intermetallic phases by means of a high power laser beam. The laser surface alloying was carried out by melting Fe and Ni...

  4. Nanostructure analysis of friction welded Pd-Ni-P/Pd-Cu-Ni-P metallic glass interface

    Ohkubo, T.; Shoji, S.; Kawamura, Y.; Hono, K.


    Friction welded Pd 40 Ni 40 P 20 /Pd 40 Cu 30 Ni 10 P 20 metallic glass interface has been characterized by energy filtering transmission electron microscopy. The interface is fully amorphous with a gradual compositional change of Cu and Ni in the range of 30 nm. By annealing above T g , the interdiffusion of Cu and Ni progressed in the supercooled liquid region, and the crystallization occurred from the Pd 40 Ni 40 P 20 glass

  5. Study of dipole interaction in micron-width NiFe/Cu/NiFe/NiO wire using exchange anisotropy

    Kimura, Takashi; Itagaki, Yoshio; Wakaya, Fujio; Gamo, Kenji


    The dipole interaction between a NiFe layer pinned by a NiO and a free NiFe layer in a micron-wide NiFe/Cu/NiFe/NiO wire was studied by changing the direction of the exchange bias from the NiO layer. The effect of the dipole interaction when the exchange bias was perpendicular to the wire axis was larger than that when the exchange bias was parallel to the wire axis, and was consistently explained by the stray field caused by the magnetic charges of the pinned layer. It was demonstrated that this method, using exchange anisotropy, is useful for investigating the dipole interaction between ferromagnetic materials separated by a nonmagnetic material in small-scale magnetic multilayers. [copyright] 2001 American Institute of Physics

  6. Effects of Ni particle morphology on cell performance of Na/NiCl2 battery

    Kim, Mangi; Ahn, Cheol-Woo; Hahn, Byung-Dong; Jung, Keeyoung; Park, Yoon-Cheol; Cho, Nam-ung; Lee, Heesoo; Choi, Joon-Hwan


    Electrochemical reaction of Ni particle, one of active cathode materials in the Na/NiCl2 battery, occurs on the particle surface. The NiCl2 layer formed on the Ni particle surface during charging can disconnect the electron conduction path through Ni particles because the NiCl2 layer has very low conductivity. The morphology and size of Ni particles, therefore, need to be controlled to obtain high charge capacity and excellent cyclic retention. Effects of the Ni particle size on the cell performance were investigated using spherical Ni particles with diameters of 0.5 μm, 6 μm, and 50 μm. The charge capacities of the cells with spherical Ni particles increased when the Ni particle size becomes smaller because of their higher surface area but their charge capacities were significantly decreased with increasing cyclic tests owing to the disconnection of electron conduction path. The inferior cyclic retention of charge capacity was improved using reticular Ni particles which maintained the reliable connection for the electron conduction in the Na/NiCl2 battery. The charge capacity of the cell with the reticular Ni particles was higher than the cell with the small-sized spherical Ni particles approximately by 26% at 30th cycle.

  7. One dimensional motion of interstitial clusters and void growth in Ni and Ni alloys

    Yoshiie, T.; Ishizaki, T.; Xu, Q.; Satoh, Y.; Kiritani, M.


    One dimensional (1-D) motion of interstitial clusters is important for the microstructural evolution in metals. In this paper, the effect of 2 at.% alloying with elements Si (volume size factor to Ni: -5.81%), Cu (7.18%), Ge (14.76%) and Sn (74.08%) in Ni on 1-D motion of interstitial clusters and void growth was studied. In neutron irradiated pure Ni, Ni-Cu and Ni-Ge, well developed dislocation networks and voids in the matrix, and no defects near grain boundaries were observed at 573 K to a dose of 0.4 dpa by transmission electron microscopy. No voids were formed and only interstitial type dislocation loops were observed near grain boundaries in Ni-Si and Ni-Sn. The reaction kinetics analysis which included the point defect flow into planar sink revealed the existence of 1-D motion of interstitial clusters in Ni, Ni-Cu and Ni-Ge, and lack of such motion in Ni-Si and Ni-Sn. In Ni-Sn and Ni-Si, the alloying elements will trap interstitial clusters and thereby reduce the cluster mobility, which lead to the reduction in void growth.

  8. First-principles calculations for the elastic properties of Ni-base model superalloys: Ni/Ni3Al multilayers

    Yun-Jiang, Wang; Chong-Yu, Wang


    A model system consisting of Ni[001](100)/Ni 3 Al[001](100) multi-layers are studied using the density functional theory in order to explore the elastic properties of single crystal Ni-based superalloys. Simulation results are consistent with the experimental observation that rafted Ni-base superalloys virtually possess a cubic symmetry. The convergence of the elastic properties with respect to the thickness of the multilayers are tested by a series of multilayers from 2γ'+2γ to 10γ'+10γ atomic layers. The elastic properties are found to vary little with the increase of the multilayer's thickness. A Ni/Ni 3 Al multilayer with 10γ'+10γ atomic layers (3.54 nm) can be used to simulate the mechanical properties of Ni-base model superalloys. Our calculated elastic constants, bulk modulus, orientation-dependent shear modulus and Young's modulus, as well as the Zener anisotropy factor are all compatible with the measured results of Ni-base model superalloys R1 and the advanced commercial superalloys TMS-26, CMSX-4 at a low temperature. The mechanical properties as a function of the γ' phase volume fraction are calculated by varying the proportion of the γ and γ' phase in the multilayers. Besides, the mechanical properties of two-phase Ni/Ni 3 Al multilayer can be well predicted by the Voigt–Reuss–Hill rule of mixtures. (classical areas of phenomenology)

  9. Flowsheet for 63Ni production

    Williams, D.F.; Knauer, J.B.; O'Kelley, G.D.; Wiggins, J.T.; Porter, C.E.


    The production of large quantities of high specific activity 63 Ni (>10Ci/g) requires both a highly enriched 62 Ni target and a long irradiation period at high neutron flux. Trace impurities in the nickel and associated target materials are also activated and account for a significant fraction of the discharged activity and essentially all of the gamma activity. While most of these undesirable activation products (mainly transition metals) can be easily removed as chloride complexes during anion exchange, chromium, present as 51 Cr, and manganese, present as 54 Mn, are exceptions and require solvent extraction of the in-cell product to achieve the desired purity. In addition to summarizing the current development and production experience, optimized flowsheets are discussed

  10. Microstructural investigations of Ni and Ni2Al3 coatings exposed in biomass power plants

    Wu, D. L.; Dahl, K. V.; Christiansen, T. L.


    The present work investigates the corrosion resistance of Ni and Ni2Al3 coated austenitic stainless steel (TP347H) tubes, which were exposed in a biomass-fired boiler with an outlet steam temperature of 540 °C for 6757 h. The Ni2Al3 coating was produced by electroplating Ni followed by low...... temperature pack cementation. After exposure, microstructural investigations were performed by light optical and electron microscopy (SEM-EDS). Electroplated Ni coatings were not protective in straw firing power plants and exhibited similar corrosion morphology as uncoated tubes. For Ni2Al3 coatings...

  11. Influence of ni thickness on oscillation coupling in Cu/Ni multilayers

    Gagorowska, B; Dus-Sitek, M [Institute of Physics, Czestochowa University of Technology, Al. Armii Krajowej 19, 42-200 Czestochowa (Poland)


    The results of investigation of magnetic properties of [Cu/Ni]x100 were presented. Samples were deposited by face-to-face sputtering method onto the silicon substrate, the thickness of Cu layer was constant (d{sub Cu} = 2 nm) and the thickness of Ni layer - variable (1 nm {<=} d{sub Ni} {<=} 6 nm). In Cu/Ni multilayers, for the thickness of Ni layer bigger than 2 nm antiferromagnetic coupling (A-F) were observed, for the thickness of Ni smaller than 2 nm A-F coupling is absent.

  12. Influence of ni thickness on oscillation coupling in Cu/Ni multilayers

    Gagorowska, B; Dus-Sitek, M


    The results of investigation of magnetic properties of [Cu/Ni]x100 were presented. Samples were deposited by face-to-face sputtering method onto the silicon substrate, the thickness of Cu layer was constant (d Cu = 2 nm) and the thickness of Ni layer - variable (1 nm ≤ d Ni ≤ 6 nm). In Cu/Ni multilayers, for the thickness of Ni layer bigger than 2 nm antiferromagnetic coupling (A-F) were observed, for the thickness of Ni smaller than 2 nm A-F coupling is absent

  13. Exclusive study of Ni+Ni and Ni+Au central collisions: phase coexistence and spinodal decomposition; Etude exclusive des collisions centrales Ni+Ni et Ni+Au: coexistence de phase et decomposition spinodale

    Guiot, B


    The INDRA multidetector allowed us to study the Ni+Ni collisions at 32A MeV and the Ni+Au collisions at 52,4 MeV. Central collisions leading to 'quasi-fused' systems were isolated using multidimensional analysis techniques: the Discriminant Analysis and the Principal Component Analysis. Comparison with a statistical model shows that the selected events are compatible with thermodynamical equilibrium. The average thermal excitation energy is 5A MeV for both systems. Calculations of heat capacities show that the deexcitation of the hot sources are akin to a liquid-gas phase transition of nuclear matter. Indeed heat capacities exhibit a negative branch as expected for a phase transition of a finite system. The dynamics of this phase transition has been investigated by applying the charge correlation method. An enhanced production of events with equal-sized fragments has been evidenced for Ni+Au at 52A MeV. No signal was found for Ni+Ni at 32A MeV. Finally this method was improved by taking into account the total charge conservation. The signal is seen more clearly for Ni+Au at 52A MeV, but is ambiguous for Ni+Ni at 32A MeV. The path followed in the state diagram, or the involved time scales, seem to be different for these systems. (authors)

  14. niños preescolares

    Claudia Rosario Portilla Ramírez


    Full Text Available Este estudio explora la relación entre la escritura y la comprensión de la referencia a través de una tarea de sinonimia en niños entre 5 y 6 años de edad, de origen latinoamericano, escolarizados en Barcelona (España. Las variables relacionadas con la tarea de sinonimia fueron (a la comprensión de la entidad lingüística nombre y (b el nivel de conceptualización de la escritura de los niños y la presencia de etiquetas escritas durante la tarea. Para la tarea de sinonimia se utilizaron pares de sinónimos dialectales del español (de Latinoamérica y de la Península Ibérica. Los resultados mostraron una diferenciación en el razonamiento de los niños, la cual dependía de la comparación entre lenguaje oral y lenguaje escrito en el desarrollo de la tarea, evidenciando una mayor aceptación de la sinonimia en la modalidad de lenguaje oral que en la modalidad de lenguaje escrito.

  15. Reinvestigation of 56Ni decay

    Sur, B.; Norman, E.B.; Lesko, K.T.; Browne, E.; Larimer, R.


    In a series of experiments, we have reinvestigated the decay of the doubly magic nucleus 56 Ni, which is believed to be copiously produced in supernovae. We have confirmed its previously known decay scheme and half-life, and have searched for several rare decay modes. We establish an upper limit of 5.8x10 -7 for the branching ratio of the second forbidden unique β + decay to the 158-keV level in 56 Co, leading to a lower limit of 2.9x10 4 yr for the half-life of fully ionized 56 Ni nuclei in cosmic rays. We also establish an upper limit of 5.0x10 -3 for the branching ratio of the isospin forbidden Fermi electron capture transition to the 1451-keV level in 56 Co, which in turn leads to an upper limit of 124 keV for the isospin mixing Coulomb matrix element of the 56 Ni ground state

  16. On the nature of Ni···Ni interaction in a model dimeric Ni complex.

    Kamiński, Radosław; Herbaczyńska, Beata; Srebro, Monika; Pietrzykowski, Antoni; Michalak, Artur; Jerzykiewicz, Lucjan B; Woźniak, Krzysztof


    A new dinuclear complex (NiC(5)H(4)SiMe(2)CHCH(2))(2) (2) was prepared by reacting nickelocene derivative [(C(5)H(4)SiMe(2)CH=CH(2))(2)Ni] (1) with methyllithium (MeLi). Good quality crystals were subjected to a high-resolution X-ray measurement. Subsequent multipole refinement yielded accurate description of electron density distribution. Detailed inspection of experimental electron density in Ni···Ni contact revealed that the nickel atoms are bonded and significant deformation of the metal valence shell is related to different populations of the d-orbitals. The existence of the Ni···Ni bond path explains the lack of unpaired electrons in the complex due to a possible exchange channel.

  17. Synthesis of Ni core NiO shell nanostructure and magnetic investigation for shell thickness determination

    Arabi, H.; Bruck, E.; Tichelaar, F.D.


    Full text: Nickel oxide has received a considerable amount of attention in recent years for its catalytic, electronic and magnetic properties. Ni nanoparticles with an average size of 8 nm were prepared by dc - arc discharge in argon atmosphere. A current of 130 A and 300 milli bar pressure of argon have been applied. The produced Ni nanoparticles were annealed for oxidizing in air at 350 for six hours to produce antiferromagnetic NiO particles. The structure of Ni and NiO nanoparticles and size estimation of them studied by means of X-ray diffraction. The size and morphology of the particles were also characterized by high resolution transmission microscopy (TEM). The Ni core NiO shell structure, resulting from the oxidation process, were studied by magnetic properties measurements. A quantum design squid magnetometer, model MPMS5S was used for measuring saturation magnetization of both nanoparticles of Ni with and without NiO layer. By knowing the density of Ni and NiO, we were able to deduce the thickness of the Ni core and NiO outer layer. They are around 3 and 5 nanometers respectively. (authors)

  18. Removal of free cyanide in waste water through complexation with Fe(II) iron followed by alkaline chlorination. Tetsu (II) ion ni yoru sakka hanno wo maeshori to suru haisuichu no yuri sian no shori

    Nishikubo, N; Tanihara, K; Yasuda, S [Government Industrial Research Institute, Kyushu, Fukuoka (Japan)


    The removal treatment of free cyanide in waste water was tested by complexation with Fe(2) ion followed by alkaline chlorination and precipitation of residual iron cyano complex to study saving of sodium hypochlorite (NaClO) for alkaline chlorination. The complexation with Fe(2) ion was studied in batch treatment under the coexistence with zinc ion assuming plating waste water, while the relation between the complexation and effective chlorine consumption in alkaline chlorination was studied in continuous treatment. As a result, the effective chlorine consumption was greatly decreased by pretreatment, and a cyanic acid ion (CNO{sup {minus}}) concentration was also lower than that in conventional methods. In the case of free cyanide with lower initial concentration, the total cyanide concentration in final treated water offered sufficiently low values only by adding zinc salt, while in higher initial concentration, it reached 1 ppm or less through precipitation by adding a reductant together with zinc salt. 9 refs., 7 figs., 2 tabs.

  19. Achievement report on research and development in the Sunshine Project in fiscal 1978. Research and development of hydrogen manufacturing technologies using the thermo-chemical method; 1978 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu kaihatsu seika hokokusho



    This paper describes a summary design of an iodine cycle experimenting equipment as one of the achievements in fiscal 1978 on research of hydrogen manufacturing technologies using the thermo-chemical method. The object of the equipment is a reaction to derive Mg(IO{sub 3}){sub 2} and MgI{sub 2} from MgO being the first reaction of the cycle, and iodine. The by-product (Q-phase) is produced according to composition of the aqueous reaction solution. The occurring reaction and composition of the produced materials vary depending on which contact system the reactor type uses, countercurrent flow or concurrent flow. Discussions were given on both types. Hydrogen generation rate of 1 Nm{sup 3}/hr was assumed as the equipment size to derive material balance and heat balance. Furthermore, types considered applicable were selected from different types of the solid-liquid reaction equipment, and summary design and calculation were performed. Process simulation provided a prospect of achieving thermal efficiency that can compete with the electrolytic process. As a study on materials for a magnesium iodate pyrolytic equipment as the second reaction, corrosion tests were carried out in a gas mixture composed of iodine, oxygen and steam. Using 26 kinds of metallic materials as the objects, the tests were executed at 100 and 300 degrees C for 100 hours. Long-term durability tests were also performed on materials judged to have good corrosion resistance. (NEDO)

  20. Imaging of active faults with the step continuous wave radar system. In case of Senzan faults in Awaji-island; Step shiki renzokuha chichu radar tansaho ni yoru katsudanso no imaging.

    Koga, K; Hara, H; Kasai, H; Ito, M [Kawasaki Geological Engineering Co. Ltd., Tokyo (Japan); Yoshioka, T [Geological Survey of Japan, Tsukuba (Japan)


    Validity of continuous wave radar exploration was verified when the said technique and some other probing methods were investigated at the Senzan Faults in Awaji Island. The signal transmitted by a continuous wave exploration system is a collection of sinusoidal waves different in frequency, and the frequencies are so controlled that they form steps relative to the sweep time. Exploration into great depths is carried out by prolonging the transmission signal sweep time, where high resolution is maintained by use of widened transmission frequency bandwidths. On-site measurements were made using a triplicated multichannel method, and electromagnetic wave propagation velocities required for depth conversion of the reflected cross section were determined in compliance with the wide angle method. On the basis of the analytical cross section using the profiles obtained by continuous radar reflection exploration conducted from the ground surface, interpretation was made of the geological structure. The presence and position and the geological development of the Senzan Faults were identified by the study of discontinuities in reflective structures such as the strata. 4 refs., 5 figs., 2 tabs.

  1. Measurements of ultrasonic waves by means of laser Doppler velocimeter and an experimental study of elastic wave propagation in inhomogeneous media; Laser doppler sokudokei ni yoru choonpa keisoku to ganseki wo mochiita fukinshitsu baishitsu no hado denpa model jikken

    Nishizawa, O; Sato, T [Geological Survey of Japan, Tsukuba (Japan); Lei, X [Dia Consultants Company, Tokyo (Japan)


    In the study of seismic wave propagation, a model experimenting technique has been developed using a laser Doppler velocimeter (LDV) as the sensor. This technique, not dependent on conventional piezoelectric devices, only irradiates the specimen with laser to measure the velocity amplitude on the target surface, eliminating the need for close contact between the specimen and sensor. In the experiment, elastic penetration waves with their noise levels approximately 0.05mm/s were observed upon application of vibration of 10{sup 6}-10{sup 5}Hz. The specimen was stainless steel or rock, and waveforms caught by the LDV and piezoelectric device were compared. As the result, it was found that the LDV is a powerful tool for effectively explaining elastic wave propagation in inhomogeneous media. The piezoelectric device fails to reproduce accurately the waves to follow the initial one while the LDV detect the velocity amplitude on the specimen surface in a wide frequency range encouraging the discussion over the quantification of observed waveforms. 10 refs., 7 figs.

  2. Stress estimation around the survey wells in Hanshin-Awaji area by means of AE/DR and DSCA experiments; AE/DR ho to DSCA ho ni yoru Hanshin Awaji chiiki chosa kui shuhen no chikaku oryoku sokutei

    Ito, H; Kuwahara, Y; Nishizawa, O [Geological Survey of Japan, Tsukuba (Japan); Yamamoto, K [Tohoku University, Sendai (Japan). Faculty of Science; Sano, O [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Yokoyama, T; Kudo, R [OYO Corp., Tokyo (Japan); Xue, Z [Kiso-Jiban Consultants Co. Ltd., Tokyo (Japan)


    A total of 5 wells were excavated in the Hanshin-Awaji area (Ikeda, Takarazuka, Tarumi, Hirabayashi and Ikunami) to collect the core samples, which were analyzed by the AE/DR and DSCA methods to determine crustal stresses. For the AE/DR analysis, the core sample was cut in the vertical direction, and in the horizontal direction at intervals of 45{degree}. The sample of unknown orientation was provided with a datum line common for both methods, to compare the results by these methods. A load was applied to the sample, provided with an AE sensor and strain gauge on the sides, in the longitudinal direction. For the DSCA analysis, the core sample was cut into a cube having a side length of 33mm, with a pair of planes directed in parallel to the datum line. A total of 18 strain gauges, 10mm in gauge length, were attached to the cube. The AE/DR analysis gave the maximum and minimum principal stresses in the horizontal plane and stresses in the vertical direction, whereas the DSCA the maximum, intermediate and minimum principal stresses. 3 refs., 7 figs.

  3. Simulation of PV/FC power hybrid system. Change of system capacity with load form factor; Taiyoko hatsuden nenryo denchi hybrid system no simulation. Fuka keijoritsu ni yoru system yoryo no henka

    Sekiguchi, N.; Tani, T. [Science University of Tokyo, Tokyo (Japan)


    Study is conducted of a photovoltaic/fuel-cell hybrid system whose power storage is a hydrogen storage that uses a hydrogen absorbing alloy. In a simulation in this research, the solar cell conversion efficiency is changed from 15.0% to 21.0% and the fuel cell power conversion efficiency from 40.0% to 50.0%, and the resultant changes in the capacity and operation rate are investigated for each of the devices in the system. The findings follow. A 1.0% change in the solar cell conversion efficiency results in a 4.8kW change in the solar cell capacity and a 1.6-ton change in the hydrogen storage capacity. With a 1.0% change in the fuel cell power conversion efficiency, there is a 14.7kW change in the solar cell capacity and a 5.3-ton change in the hydrogen storage capacity. The fuel cell capacity is not dependent on the solar cell conversion efficiency or fuel cell power conversion efficiency but on the maximum load in each of the load form factors. The rate of occurrence of an operation rate of less than 30% is 54.7% both in DC/DC converter and hydrogen generator, 24.6% in fuel cells, and 16.7% in the DC/DC inverter. 7 refs., 7 figs., 1 tab.

  4. Dynamic programming for reduction of fuel consumption in a photovoltaic/wind/diesel generating system; Doteki keikakuho ni yoru taiyoko/furyoku/diesel hatsuden system no nenryo shohiryo no sakugen

    Ishikawa, K.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)


    Dynamic programming is employed in the study of the operation of the diesel engine in a photovoltaic/wind-force/diesel-engine power generating system, which aims at reduction in the system fuel consumption and at determining an optimum system constitution. The parameters set in this system are the photovoltaic/wind-force supply rate, photovoltaic/wind-force power generation ratio, and battery capacity. An island in Ise Bay, with an annual load power of approximately 1.59-million kWh and mean daily load power of approximately 4336kWh is assumed as the location for the system. Observation data of Ommaezaki Weather Station are utilized for the calculation of the amount of photovoltaic/wind-force power generation. It is found as the result that the fuel consumption of the diesel engine in this system decreases to 82-84% when the natural energy supply rate is 20%. It is also found that the fuel consumption of the system records the minimum at a photovoltaic/wind-force ratio of 60/40, irrespective of the battery capacity or natural energy supply rate, and this ratio is the optimum ratio. 3 refs., 9 figs., 1 tab.

  5. FY1995 study of the development of high resolution sub-surface fluid monitoring system using accurately controlled routine operated seismic system; 1995 nendo seimitsu seigyo shingen ni yoru chika ryutai koseido monitoring no kenkyu



    The development of new seismic sounding system based on the new concept of ACROSS (Accurately Controlled Routine-Operated Signal System) are aimed. The system includes not only new seismic sources but also the analyzing software specialize for the monitoring of the change in subsurface velocity structure, especially in the area of fluid resources. Powerful sources with good portability are strongly required for the practical data acquisition. Portable ACROSS sources (HIT) are developed. The system is mainly used to obtain the high resolution structure with relatively short penetration distance. The principal specifications are as follows: (1) 100Hz in maximum. (2) Linearly oscillating single force. This is generated by the combined two rotator moving opposite directions. (3) Variable force with little work. (4) Very simple source-ground coupler just put even on the soft ground. The system was operated at Yamagawa geothermal plant for two months. The result of the experiments are: (1) We confirmed the stability of the source over wide frequency range up to 100Hz. (2) We confirmed that amplitude and phase of ACROSS signal can be obtained very precisely. (3) Very small change of signal which arise from subsurface velocity change are detected. This indicates that the system can detect the slight velocity change due to variation of subsurface fluid system. (NEDO)

  6. Achievement report for fiscal 1976 on Sunshine Program. Research on hydrogen production technology (Research on hydrogen production technology using thermochemical method); 1976 nendo suiso no seizo gijutsu no kenkyu seika hokokusho. Netsukagakuho ni yoru suiso seizo gijutsu no kenkyu



    This report covers part of the efforts to develop new hydrogen production technologies. Out of many processes involving Cu-halogen and alkali carbonate-iodine systems proposed as novel thermochemical processes, after they are compared with each other, a process of a sodium carbonate-iodine system with nickel in between is chosen. The chosen process is deemed to be the most excellent among the processes disclosed up to fiscal 1975. A feasibility study is conducted for the chosen process from the viewpoint of reaction rate, separation of reactive substances from each other, method for reaction manipulation, materials for device constitution, and thermal efficiency. As for the measurement of reaction rate for each unit reaction, basic reaction data are determined centering about the nickel iodide decomposition reaction and the sodium iodide carbonation reaction, and then reaction conditions which are roughly satisfying are obtained. A larger reaction unit is built in which the amounts of substances that come into reaction are approximately 10 times larger than those in the ones used in basic experiments. The progress of reactions is observed in the reaction unit, with the size enlarged in preparation for future construction of still larger reaction units. Methods for selectively isolating hydrogen out of gases ensuing from the decomposition are evaluated from the viewpoint of energy efficiency. In the selection of a reaction manipulation method, a single unit reaction process is advocated, and its thermal efficiency is estimated. (NEDO)

  7. FY 1974 report on the results of the Sunshine Project. R and D of the hydrogen production technology by the thermochemical method; 1974 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu kaihatsu seika hokokusho



    In relation to the R and D of the hydrogen production technology by the thermochemical method, the paper summed up the results of the research conducted in FY 1974. The items for study are as follows. (1) Basic model making for process simulator. (2) Type of facility on the assumption of pilot plant size, and rough selection of equipment structural materials. (3) Extraction of engineering study subjects and working-out of study plans. In (1), the basic model of simulator was established, case studies of various Fe-Cl cycles were made, and a calculation method for the balance of the whole process was established. In (2), it was concluded that in the normal pressure reaction experiment, the oxygen emits extremely little in amount in Mark 9 No. 2 reaction, and therefore, it is very doubtful whether the closed cycle will be completed using this reaction. It was also found out that No. 3 reaction is low in reaction completion degree and it is the problem in point of thermal economy. Accordingly, possibilities of reaction were reviewed, and 6 cycles were found as Fe-Cl cycle. For these reaction cycles, a process flow sheet was made. Comparative studies among processes were conducted, and the cycle structural elementary reaction in Fe-Cl process was specified. (NEDO)

  8. Cross-flow filtration of yeast extract with multi-tubular membrane module and rotating-disk membrane module; Makukaitengata heibanmaku module to tankanjomaku module ni yoru kobo hasaieki no cross flow roka

    Matsushita, K.; Shimizu, Y.; Watanabe, a. [Toto Ltd., Kitakyushu (Japan)


    A membrane separation experiment was made with multi-tubular membrane module and rotating-disk membrane module to study the cross-flow filtration of yeast extract. The membrane was an alumina precision filtration membrane with 0.15 micron m diameter pores. A multi-tubular membrane which was 19 in number of channels and 0.113{sup 2} in effective membrane area was fitted to the multi-tubular membrane module. A rotating-disk membrane which was 0.071m{sup 2} in effective membrane area was fitted to the rotating-disk membrane module. Judging from the concentration speed and factor, the rotating-disk type is more advantageous in concentrating the suspension than the multi-tubular type. The soluble high-molecular component was more easily filtrated through the rotating-disk type, which is judged attributable to its possible operation at a high flow rate on the membrane surface without necessitating a high-flow rate circulation pump. As compared with the conventional cross-filtration type, the rotating-disk type gives a high permeate flux even at a high concentration factor. 11 refs., 5 figs.

  9. Noninvasive brain metabolism measurement using carbon-13 magnetic resonance spectroscopy ({sup 13}C-MRS); Tanso 13 jiki kyomei spectroscopy ({sup 13}C-MRS) ni yoru mushinshuteki notaisha keisoku

    Okamoto, K.; Tsukada, Y. [Toshiba Corp., Tokyo (Japan)


    Carbon-13 magnetic resonance spectroscopy ({sup 13}C-MRS) and research and development efforts for brain metabolism measurement are described. Brain metabolism is a process characterized in that it not only extracts energy by disintegrating grape sugar that is the practically sole source of energy into H2O, CO2, etc., but also vigorously synthesizes amino acids that perform important functions in neural transmission, such as glutamic acid, glutamine, and {gamma}-amino acid. MRS is a technique that utilizes the magnetic resonance, which is generated when an atomic nucleus with a spin is placed in a magnetic field, for the isolation and identification of chemicals in a living body through examining the delicate difference in the magnetic resonance frequencies of the nuclei under observation. Since the signals from {sup 13}C are low in intensity as compared with those from other nuclides, a method was contrived around 1980, which observes {sup 1}H combined with {sup 13}C in grape sugar and amino acids, named the HSQC (heteronuclear single quantum coherence) method. The author et al., combining gradient magnetic pulses with HSQC, actually measure Homo sapiens brain metabolism using {sup 13}C-MRS, and now believe that the technology will be put to practical application. 7 refs., 10 figs., 1 tab.

  10. FY 2000 report on the survey of technology to reduce vehicle weight by applying new materials; 2000 nendo shinzairyo no tekiyo ni yoru jidosha keiryoka gijutsu no chosa hokokusho



    As to the technology to reduce vehicle weight with the aim of energy conservation, survey was made of the present situation and technical subjects. Further survey was conducted on the applicability of ferrous and aluminum mesoscopic system control materials (super metal) under development. The application of high-tensile steel to vehicles is rapidly being developed as a means of weight reduction. To increase a rate of the use of high-tensile steel, limits of forming, characteristic improvement and rigidity need to be removed. Further, concerning the application of aluminum, subjects are press formability and joining. In regard to the development of ferrous super metal, characteristics with high ductility were obtained despite of such high strength as tensile strength of 930MPa, uniform elongation of 17%, and total elongation of 27%, which indicated that the super metal has an applicability to vehicle use thin steel sheets. The ferrous super metal, which enables the production of high-tensile steel sheet with no use of much alloy elements, is a material with high recycling ability. The aluminum super metal has also an applicability to vehicles. (NEDO)

  11. Report on an investigational research on energy conservation by a combination system between air compressor and pneumatic equipment in fiscal 1995; 1995 nendo kuki asshukuki to kukiatsu kiki no kumiawase system ni yoru sho energy no chosa kenkyu hokokusho



    The air compressor which rises pneumatics for actuating pneumatic equipment is very low in energy efficiency also including the power source. Conventionally, at works which use large lots of compressor power, for example, improvements have been made on such as leakage of pneumatics from compressor and pneumatic equipment and piping for power reduction, but the present situation is that processing including compressor and pneumatic compressor through exhaust gas treatment is not regarded as a synthetic system. Therefore, the following problems should be studied: (1) distributed installation of compressors at right place from centralized installation, reduction of pressure loss of piping, etc., and how to use pneumatic equipment and how to improve its performance; (2) energy conservation by lessening gap between compressor pressure and pressure in using pneumatic equipment; (3) energy conservation by improving exhaust gas treatment, etc. This time, an investigational research on these items was systematically conducted to study measures for energy reduction of power source and increase of efficiency. The study was made on making guides such as manuals which becomes effective for energy conservation measures and policies to be guidelines on the development of equipment. 9 refs., 46 figs., 9 tabs.

  12. FY 2000 Report on survey results. Curtailment of the carbon dioxide emission by effective use of woody biomass system waste; 2000 nendo mokushitsu biomass kei haikibutsu no yuko riyo ni yoru nisanka tanso haishutsu no sakugen



    It is estimated that the woody biomass resources in Japan total 42.70 million t/y on a dry basis (indigenous production: 20.00 million t/y), which corresponds to 18.00 million t/y as oil. This project studies effective utilization of low-quality biomass resources now discarded, e.g., thinning materials and demolition woods, by reference to biomass utilization pursued in European and North American countries. The study activities cover the 3 areas of woody biomass wastes, current status of biomass utilization technologies in the overseas countries, and feasibility of introduction of the utilization technologies, after investigating necessity of abatement of the green-effect gases, current status of energy demands and policies, and woody biomass. Utilization of biomass resources for low-temperature heat purposes, which is the central issue in Japan, is not well established both technologically and politically. Moreover, the biomass resources are not exposed to price competition. Based on these premises, a total of 6 scenarios are proposed to promote utilization of biomass resources, including power/heat co-generation at a wood processing center, and dual firing at existing coal-fired boilers. (NEDO)

  13. Determination of sup 238 U in marine organisms by inductively coupled plasma mass spectrometry. Yudo ketsugo plasma shitsuryo bunsekiho ni yoru kaiyo seibutsuchu no sup 238 U no teiryo

    Ishii, T.; Nakahara, M; Matsuda, M.; Ishikawa, M. (National Institute of Radiological Sciences, Ibaraki (Japan))


    Since the {sup 238} U concentration in seawater is about 3ng/ml at the element level and the activity concentration is 40 {mu} Bq/ml which are considerably higher that those of other {alpha} radioactive materials, it is necessary to study the concentration levels of many marine organisms. After confirming that the inductively coupled plasma mass spectrometry as a new high sensitive analysis for multi-elements is effective to analyze heavy elements such as rare earth elements or uranium, etc., this method was applied to determine {sup 238} U in 55 species of marine organism. The {sup 238} U concentration in soft tissues of marine animal ranged from 0.076 to 5000ng/g wet weight and large difference of concentration was observed depending on the kind of animal and the tissue. Especially, the branchial heart of cephalopod molluscs showed the specific accumulation of {sup 238} U. The concentration factor of branchial heart of Octopus vulgaris which showed the highest value was calculated to be about 10 {sup 3} by comparing it with the concentration of {sup 238} U in Japanese coastal waterseas. The concentration of {sup 238} U in 20 species of algae ranged from 10 to 3700ng/g dry weight. 11 refs., 2 figs., 9 tabs.

  14. Bioremediation of recalcitrant chemical pollutant-contaminated soil. Applying edible mushroom cultivation waste to bioremediation; Kinoko kinsho ni yoru nanbunkaisei busshitsu osendo no bioremidiation. Kinoko kinsho no rigunin bunkai koso kassei to takan hokozoku tanka suiso no bunkaino

    Okada, S.; Oide, E.; Oshima, Y.; Tsuji, H. [Obayashi Corp., Tokyo (Japan)


    Bioremediation is a viable and cost effective method for soil contaminated with a variety of chemical pollutants. White-rot fungi, with emitted extracellular free radicals, are known to be able to decompose lignin, which is usually nonbiodegradable by most bacteria. The decomposition mechanism has been shown to be attributed, at least in part, to lignolytic peroxidases. We examined a method that utilizes edible mushroom cultivation waste as the microbial source, and found that these waste materials have high lignolytic peroxidase activity and degradated polyaromatic hydrocarbons in sands. (author)

  15. Preparation and properties of TiO2 films by complexing agent-assisted sol-gel method. Yuki haiishi wo mochiita sol gel ho ni yoru TiO2 usumaku no sakusei to seishitsu

    Nishide, T [Nissan Motor Co. Ltd., Tokyo (Japan); Mizukami, F [National Chemical Laboratory for Industry, Tsukuba (Japan)


    In order to control optical properties of TiO2 thin films, the TiO2 films were prepared by the sol-gel method using glycols or their ether derivatives as organic ligands to study the effect of the organic ligands on the refractive indices and crystal phases. Samples were prepared as follows: Organic ligand was added into the ethanol solution of Ti(O-iso-pr) 4, and aqueous nitric acid solution was added after reflux, and sol obtained by subsequent reflux was applied on soda lime glass or silicon wafer substrates, which were baked at 400 to 900 centigrade. Three kinds of ligand such as 2-(2-methoxyethoxy) ethanol were used. Measured items are the film thickness, thermal characteristics, crystal phase and refractive indices of thin films. The key points are as follows: In case of TiO2 thin films on the soda lime glass substrate, the changing pattern of refractive indices by temperature changes with the kind of ligand used and further the peak strength of anatase changes with the kind of ligand used. In case of silicon wafer substrates, the peak strength of anatase and rutile changes with the kind of ligand. The refractive indices and crystal phase can be controlled by properly using the ligand. 7 refs., 11 figs.

  16. Fiscal 2000 achievement report on development of high-efficiency high-reliability welding technology through improvement on welding techniques; 2000 nendo yosetsu gijutsu no kodoka ni yoru kokoritsu koshinraisei yosetsu gijutsu no kaihatsu seika hokokusho



    Efforts are made to develop a welding design support system capable of increasing reliability and enhancing welding efficiency. Activities are conducted in the six fields of (1) the development of welding process simulation models, (2) development of welded section structure simulation models, (3) development of simulation models for predicting welding caused deformation, (4) integration of the models, (5) analysis of the welding phenomenon, and (6) the elucidation of the defect generation mechanism. In field (1), efforts are made to develop an arc plasma model, a molten pool convective heat transportation model, and a welding process model. In the effort to develop an arc plasma model, studies are made about a stationary axisymmetric arc in its steady state and about a constitutive equation and computation algorithm for developing a model in which a tungsten electrode (cathode) and an arc plasma welding pool (anode) are integrated. Furthermore, the simulation outcomes are experimentally verified. Satisfactory models are obtained as far as qualitative properties are concerned. (NEDO)

  17. FY1995 development of a clean CVD process by evaluation and control of gas phase nucleation phenomena; 1995 nendo kisokaku seisei gensho no hyoka to seigyo ni yoru clean CVD process no kaihatsu



    The purpose of this study is to develop a high-rate and clean chemical vapor deposition (CVD) process as a breakthrough technique to overcome the problems that particles generated in the gas phase during CVD process for preparation of functional thin films cause reduced product yield and deterioration of the films. In the CVD process proposed here, reactant gas and generated particles are electrically charged to control the motion of them with an electric field. In this study, gas-phase nucleation phenomena are evaluated both theoretically and experimentally. A high-rate, ionized CVD method is first developed, in which reactant gas and generated particles are charged with negative ions generated from a radioisotope source and the UV/photoelectron method, and the motion of the charged gas and particles is controlled with an electric field. Charging and transport processes of fine particles are then investigated experimentally and theoretically to develop a clean CVD method in which generated particles are removed with the electric forces. As a result, quantitative evaluation of the charging and transport process was made possible. We also developed devices for measuring the size distribution and concentration of fine particles in low pressure gas such as those found in plasma CVD processes. In addition, numerical simulation and experiments in this study for a TEOS/O{sub 3} CVD process to prepare thin films could determine reaction rates which have not been known so far and give information on selecting good operation conditions for the process. (NEDO)

  18. Measurement of excited oxygen (O2:[sup 1][Delta]g) concentration by spontaneous emission. Hakko kyodo ni yoru reiki sanso ([sup 1][Delta]g) nodo no sokutei

    Takahashi, S.; Hasegawa, Y.; Yamashita, I. (Mechanical Engineering Laboratory, Tsukuba (Japan))


    The concentration of excited oxygen ([sup 1][Delta]g), which was generated by microwave discharge in a pure oxygen flow, was measured from the intensity of spontaneous emission. The conversion factor to density was determined by spectroscopic analysis of the rotational structure and calibration of the emission intensity using a black-body furnace as light source. Consequently, a good agreement was found between the observed profiles and those calculated from spectroscopic data, and it was illustrated that the absolute concentration can be obtained by coupling band analysis and the calibration method. In addition, even when the concentration was low, it was shown that the excited oxygen concentration can be measured by considering the reflection at the cell wall. The excited oxygen concentration at the microwave discharge cavity was estimated to be around 1% under the pressure ranging from 0.5 torr to 2 torr. Furthermore, the comparison of the profiles calculated at different temperature provided that the band profile can be a good indicator of gas temperature when the signal-to-noise ratio is high. 9 refs., 10 figs., 2 tabs.

  19. Low temperature formation of ferroelectric PbTiO3 films by laser ablation with 2nd laser irradiation; Reiki hikari laser heiyo laser ablation ho ni yoru kyoyudentai PbTiO3 usumaku no teion keisei

    Tabata, H.; Kawai, T. [Osaka University, Osaka (Japan)


    The unique advantage of the pulsed laser deposition is its ability to produce highly oriented stoichiometric films at a low substrate temperature. Ferroelectric PbTiO3 thin films have been formed using 2nd laser assisted laser ablaion technique at low temperature, i.e., 350degC, on Sr7iO3 single-crystal substrates and Pt/MgO electrodes. The second laser irradiation at the substrate surface is quite effective for crystallization of the films at low substrate temperature below 400degC. The suitable energy density (fluence) of the irradiation laser is in the range of 30-100 mJ/cm{sup 2}. X-ray diffraction patterns of PbTiO3 thin films show c-axis orientation, with a rocking angle of 1.0 - 0.5deg. These films exhibit ferroelectric hysteresis loop. The dielectric constant and remanent polalyzation of the PbTiO3 films are in the range of 120-150 and 60-80 {mu}C/cm{sup 2}, respectively. 31 refs., 10 figs., 1 tab.

  20. Characteristics of the fluorescent substances in the Yodo River system by three-dimensional excitation emission matrix spectroscopy; Sanjigen reiki/keiko kodoho ni yoru yodogawa suikeichu no keiko busshitsu no tokucho

    Suzuki, Y.; Nakaguchi, Y.; Hiraki, K.; Kudo, M.; Kimura, M.; Nagao, S. [Japan Atomic Energy Research Inst., Tokyo (Japan)


    Organic substances in the river water in Yodo River system were analyzed by three-dimensional excitation emission matrix spectroscopy. Fluorescent substances were taken as an index of organic substances. The amount of fluorescent substances varied widely depending on the environment of river basin. It is suggested that the fluorescent substances are composed of organic substances which is not directly originated from biological activity. It is suggested that the fluorescent substances were produced by leaching of river bottom sediment. The fluorescent substances in Yodo River system consists of fulvic acid-like substances and protein. The analysis of fluorescent substances in river water by three-dimensional excitation emission matrix spectroscopy can be useful means for estimation of variation and origin of fluorescent substances. For better understanding of features of fluorescent substances in the surface water into which various kinds of substances enter, it is necessary to determine the exact sampling points based on the consideration of different sources and to make a database of peak positions for identification of fluorescent substances from fluorescence intensity peak. 29 refs., 3 figs., 2 tabs.

  1. Effect of surface irradiation during the photo-CVD deposition of a-Si:H thin films. Hikari CVD ho ni yoru amorphous silicon sakuseiji no kiban hikari reiki koka

    Tasaka, K.; Doering, H.; Hashimoto, K.; Fujishima, A. (The University of Tokyo, Tokyo (Japan))


    This paper shows the impact of the irradiation from an additional light source during the deposition of hydrogenated amorphous silicon by photo-CVD deposition. Using a mercury sensitized photo-CVD process from Disilan (Si {sub 2} H {sub 6}) and hydrogen, silicon was deposited. A 40W low pressure mercury lamp was applied as the light source. A portion of the substrate was in addition irradiated using an Xg-He lamp through a thermal filter. Irradiation of the substrate using only Xg-He lamp produced no deposition, since this light has a wavelength which is too long to produce the SiH {sub 3}-radicals needed for Si deposition. The additional Xg-He light source was discovered to cause an increased thickness of deposited a-Si:H film and a transmission of the band structure. The reasons of these are considered that the influence of irradiation is not limited to film thickness, but that irradiation also impacts the composition of the a-Si:H film so as to cause a reduction in the hydrogen content. 10 figs., 1 tab.

  2. Non-contact estimation of the bond quality in soldered thin laminate by laser generated lamb waves; Laser reiki ramuha ni yoru handazuke sekisohaku no setsugo seijo no hisesshoku hyoka

    Kasama, H.; Futatsugi, T.; Cho, H.; Takemoto, M. [Aoyama-Gakuin University, Tokyo (Japan). Faculty of Science and Engineering


    The bond quality of a solder-bonded copper laminated plate was modeled into rigid contact (rc) and slip contact (sc) to calculate the velocity dispersion of lamb waves. The velocity dispersion of laser generated lamb waves was measured, and the bond quality or the thickness of a solder layer was evaluated by non-contact. In the model whose bond surface is rc, the velocity dispersion of lamb waves can be calculated under conditions where the stress and displacement in an interface are continuous. In the model whose bond surface is sc, it can be calculated under conditions where an interface slips freely. Weak bond indicates the velocity dispersion between rc and sc. In this model, the velocity dispersion can also be calculated by a change in the thickness of a solder layer and used for quantitative evaluation of a bond interface. A three-layer solder bond manufactured for trial could be evaluated from the velocity dispersion of laser lamb waves. At the room temperature, the change in bond quality near the solder melting point of bond laminate that was judged as rc was investigated. When the solidus temperature is exceeded, the amplitude of lamb waves and the velocity dispersion changed largely. The amplitude of lamb waves increases as the liquid phase ratio increases. The bond quality near the solder melting point can be evaluated using lamb waves. 9 refs., 10 figs., 2 tabs.

  3. Excitation of tsunami by a pure strike-slip earthquake. ; Izu Oshima kinkai earthquake tsunami on Feb. 20, 1990. Yokozure danso jishin ni yoru tsunami no reiki. ; 1990 nen 2 gatsu 20 nichi Izu Oshima kinkai jishin tsunami

    Abe, K. (Nippon Dental University, Tokyo (Japan). Niigata Junior College); Okada, M. (Meteorological Research Institute, Tsukuba (Japan))


    A numerical experiment was performed to reproduce the tsunami from the Izu-Oshima Kinkai Earthquake which occurred on February 20, 1990, using a tsunami excited by a pure strike-slip fault. An existence of a vertical fault with a length of 15 km and a width of 12 km was hypothesized in the south-north direction on the ocean bottom around the focal region. Then, a tsunami was assumed to have been excited when the fault was given a side-slip movement to create discrepancies of 1 m in the fault. Water level change for one hour after onset of the tsunami was calculated in one-second interval in each unit square with a side length of 1 km over an ocean area of 200 km from east to west and 150 km from north to south centering on the wave source. The results obtained from the calculation were harmonious with tsunami waveforms observed at five stations in the subject region and their spectral analytic results. Reproduced were the two predominant frequencies commonly observed at more than two stations, and difference in predominant cycles that appear according to azimuths of the observation points to the epicenter. These facts endorse the reasonability of the above hypothesis. 9 refs., 11 figs.

  4. Amplification of picosecond pulse by electron-beam pumped KrF laser amplifiers. Denshi beam reiki KrF laser zofukuki ni yoru piko byo pulse no zofuku

    Okuda, I.; Tomie, T.; Owadano, Y.; Yano, M. (Electrotechnical Laboratory, Tsukuba (Japan))


    Experiments on the amplification of a picosecond pulse by electron-beam pumped KrF laser amplifiers were carried out for the purpose of its application to the field such as excitation light source for soft X-ray laser which requires large energy besides peak power. The picosecond pulse was amplified by a discharge pumped KrF amplifier and two electron-beam pumped KrF amplifiers(at the middle stage and the final stage). The energy of 4J, which was the largest energy for short pulse excimer laser so far, was obtained by these devices. About 90% of the window area of the final amplifier with 29cm diameter was filled by the input beam, and energy density of the picosecond beam reached 3.9 times saturation energy density. Measured energy of amplified spontaneous emission(ASE) showed good agreement with the theoretically estimated value. Most of ASE was derived from the discharge pumped laser as the first amplifier. As for the focused power density, the power density ratio of the picosecond pulse to ASE was estimated to be as large as 10{sup 5}. 11 refs., 4 figs.

  5. Acoustic excitation of diffusion flames with coherent structure in a plane shear layer.; Effects of acoustic excitation on combustion properties; Soshiki kozo wo tomonau sendan kakusan kaen no onkyo reiki.; Onkyo reiki ni yoru nensho tokusei no henka

    Ishino, Y.; Kojima, T.; Oiwa, N.; Yamaguchi, S. [Nagoya Institute of Technology, Nagoya (Japan)


    This paper reports on experiments for acoustic excitation of plane shear structured flame. Flows of air separated into the higher velocity side and the lower velocity side by a partition on the center of a flow path merge at the measuring point to form a mixed layer with coherent structure. Fuel is supplied to this mixed layer with the flows so adjusted that the generated flame will attach to the partition on the lower velocity side. Acoustic excitation (at a sound pressure level of 100 dB to 120 dB) is performed in a speaker fitted on a wall on the higher velocity side. The paper mentions the results of the experiments as follows: the acoustic excitation produces such changes to diffusion flame in the plane shear layer as shorter flame and blue flame combustion and clarification of flame structures; as seen from spectral characteristics of temperature change in the flames, a flame acoustically excited strongly presents remarkable improvements in periodicity of the structure; as seen from sound pressure distribution in the flow direction at the measuring point, the flame zone of the flame acoustically excited strongly is positioned at the middle of the node and loop of a standing wave. 6 refs., 9 figs., 1 tab.

  6. Achievement report for fiscal 1998. Research and development of super-functional environment-resistant materials by controlling trace metal ion implantation; 1998 nendo seika hokokusho. Gokubiryo kinzoku ion chunyu seigyo ni yoru chokino taikankyo zairyo no kenkyu kaihatsu



    The aim was to develop reliable materials high in resistance to hostile environments, greatly improved in their resistance to oxidation, abrasion, and corrosion at high temperatures. To achieve the goal, trace quantities of high melting point metals were implanted into the compound formed on the substrate surface or deep into the substrate material. This year's research and development is outlined below. Important technologies in the ion process involved materials which at high temperatures were very resistant to oxidation, abrasion, and corrosion. The high-temperature oxidation resistant material was studied for use with the automobile supercharger rotor. The study on the high-temperature abrasion resistant material involved Ti-N thin coatings: the optimization of coating conditions, slidability at room temperature, and slidability in a high-temperature atmosphere. As for the high-temperature corrosion resistant material, studies were made to use it for refuse-fueled power generation. The TiAl material was also studied: the effect of ion implantation on the improvement of its high-temperature oxidation resisting capability, analysis into oxidized alloy surface properties, ion implantation into complicatedly shaped items and the optimum material for them, and the surface treatment by ion beams for improving resistance to high-temperature corrosion. (NEDO)

  7. Secretive production of long-chain fatty acids, triacylglycerols and n-alkane-2-ones by fermentation processes; Hakkoho ni yoru ekitai nenryo no seisan wa kanoka (shishitsu no bunpi seisan)

    Fukui, S. [University of Fukuyama, Hiroshima (Japan). Faculty of Engineering


    Secretive production of lipids, which are useful source for engine-driving fuel, by microbial process using carbohydrate biomasses as substrate has been investigated in our laboratory. This review consists of four parts concerning breedings and selection of lipid-secretive microorganisms : (1) breedings of long-chain fatty acid-secretive strains from Candida lipolytica L-1 by a step-wise mutagenesis process, (2) selection of a triacylglycerol (TG)-secretive and accumulative yeast strain Trichosporon sp. SH45Y, (3) breedings of mutants, SH45Y-derivatieves, having potent ability to produce TG secretively from glucose, a typical biomass charbohydrate, and (4) selection of microorganisms which produce liquid-n-alkane in culture medium by utilizing long-chain fatty acids and TG; a strain of Penicillium decumbens can produce liquid alkalis with a yield of approximately 60 % in weight from palm kernel oil, a commercial TG. 10 refs., 7 figs., 7 tabs.

  8. Three-dimensional computer simulation at vehicle collision using dynamic model. Application to various collision types; Rikigaku model ni yoru jidosha shototsuji no sanjigen kyodo simulation. Shushu no shototsu keitai eno tekiyo

    Abe, M; Morisawa, M [Musashi Institute of Technology, Tokyo (Japan); Sato, T [Keio University, Tokyo (Japan); Kobayashi, K [Molex-Japan Co. Ltd., Tokyo (Japan)


    The past study of safety at vehicle collision pays attention to phenomena within the short time from starting collision, and the behavior of rollover is studied separating from that at collision. Most simulations of traffic accident are two-dimensional simulations. Therefore, it is indispensable for vehicle design to the analyze three-dimensional and continuous behavior from crash till stopping. Accordingly, in this study, the three-dimensional behavior of two vehicles at collision was simulated by computer using dynamic models. Then, by comparison of the calculated results with real vehicles` collision test data, it was confirmed that dynamic model of this study was reliable. 10 refs., 6 figs., 3 tabs.

  9. Attempt of lean burn of a 4 cycle gasoline engine by the aid of low pressure air assisted in-cylinder injection; Tonai kuki nenryo funsha ni yoru lean burn no kokoromi

    Hatakeyama, S; Kondo, M; Sekiya, Y; Murayama, T [Hokkaido Automotive Engineering College, Hokkaido (Japan)


    Comparable performance and exhaust emission with conventional carburetor was obtained by a low Pressure air assisted in-cylinder injection system. And lean burn of idling and light load operation till A/F=70 was realized by installing a spark Plug and a reed type injection nozzle in a divided combustion chambaer of a 4 cycle gasoline engine. 2 refs., 10 figs.

  10. Joint stiffness identification of body structure using neural network. Jointed part composed of 2 beams; Neural network ni yoru shatai kozo no ketsugo gosei dotei. Buzai 2 hon kara naru ketsugobu no baai

    Okabe, A; Tomioka, N [Nihon University, Tokyo (Japan)


    The method to obtain a joint stiffness value from displacements of jointed part using hierarchical neural networks in case of a jointed part composed of two beams were proposed. First, the sample data of displacements of jointed part vs. joint stiffness are prepared as learned data. Second, the relations between displacements of jointed part and joint stiffness are constructed from these learned data using a hierarchical neural networks. It was found that the value of joint stiffness can be obtained from displacement of jointed part by the trained neural network. 4 refs., 9 figs., 2 tabs.

  11. FY 2000 Fundamental study for promotion of jointed implementations. Feasibility study on reducing greenhouse gas emissions by modernizing Thanlyin Refinery in Myanmar; 2000 nendo Myanmar koku Thanlyin seiyusho kindaika ni yoru onshitsu koka gas haishutsu sakugen kanosei chosa hokokusho



    The feasibility study was conducted on a project in Myanmar for the energy saving effect and reduction of the greenhouse gas emissions by introducing modern refining facilities in Thanlyin Refinery of Myanmar Petrochemical Enterprise. The project items selected as a result of the study are improvement in the heat recovery efficiency of crude distillation unit, improvement in the furnace efficiency of crude distillation unit and coker plant, improvement in the efficiency of power plant, reduction of steam loss, modernization of the cooling water system, recovery and reuse of off-gas and LPG in crude distillation unit, and modernization of intermediate products run-down system. The conceptual designs and studies on these items indicate that implementation of these projects could lead to energy saving of 25,844 tons/y as crude and CO2 emission abatement of 57,457 tons/y, 46% and 33% reduction from the baseline. The total expenses for all of these items are estimated at 4,300 million yen. These are judged to be promising projects, with estimated investment recovery period of 9 years and internal profit rate of 12.9%, when the special yen loans are available. (NEDO)

  12. Fiscal 1998 development report on the high-accuracy quantitative analysis technique of catalyst surfaces by electron spectroscopy; 1998 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu



    This project aims at development of the high-accuracy quantitative analysis technique by electron spectroscopy for surface analysis of catalysts and semiconductors. Since conventional analysis technique using an energy-fixed X-ray excitation source is inadequate to obtain satisfactory surface sensitivity and quantitative accuracy for catalysts, for development of the titled technique, this project makes experiment using energy-variable synchrotron radiation to modify the parameter on motion of low-speed electrons in solids which is obtained by Monte Carlo calculation. For establishment of the high-accuracy quantitative analysis technique of surface compositions of materials such as catalyst of which performance is dominated by utmost surface, the project studies the attenuation length of electrons in solids by electron spectroscopy using soft X-rays from synchrotron radiation. In this fiscal year, the project established the equipment and technique for high-accuracy quantitative analysis of the thickness and electron attenuation length of silicon oxide films on silicon wafers by electron spectroscopy. (NEDO)

  13. Fiscal 1999 international cooperation project report. Development of high-precision quantitative analysis technology for catalyst surfaces by electron spectroscopy; 1999 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki bijutsu no kaihatsu seika hokokusho



    This project targets to make analysis of surface chemical phenomena of solid catalysts possible, and establish the basis of intelligent design for catalytic materials, through development of an advanced electron spectroscopy for surface analysis. In fiscal 1999, the research was promoted by using the diffraction grating and driving mechanism introduced in fiscal 1998, and by developing the measurement result on silicon oxide films by radiation beam photoelectron spectroscopy. The measurement technique was established by the optimized measurement process which can treat variable parameters as constant. The analysis result of measurement data in fiscal 1999 showed the dependence of an electron damping length in silicon oxide films on radiation photon energy. The energy dependence well agreed with a theoretically obtained inelastic mean free path of electrons qualitatively, while was smaller by nearly 30% than the latter quantitatively. Measurement was made on the damping length in oxidation-active Gd and Nd oxide films. In both cases of Si and Si oxide film substrates, oxidation of substrates or formation of silicate was observed. (NEDO)

  14. Estimation of real ship propelling performance by the surface velocity lattice method using model ship flow field data; Mokeisen ryujo data wo mochiita hyomen uzu koshiho ni yoru jissen suishin seino no suitei

    Kai, H; Ikehata, M; Sakai, S [Yokohama National University, Yokohama (Japan). Faculty of Engineering


    This is basically a technique wherein the wing element method is replaced by a surface vortex lattice method. A horseshoe vortex of unknown intensity and source surface of known intensity are distributed on the wing surface and, under conditions that the fluid will not cross the boundary, the intensity of horseshoe vortex circulation is calculated for the solution of the fluid field. For the simulation of a real ship in navigation, the required propeller revolution thrust is determined using the real ship resistance value and real ship thrust reduction factor estimated from a model ship resistance test by extrapolation. The calculation of propeller performance is conducted in the quasi-steady condition using the force of fluid working on one wing for each wing angle (with the wing rotated at the increment of 6 degrees), and the thrust and torque are determined using the averages of values obtained in one cycle. It is found that the torque value is overestimated in a considerable degree in the wing element theory. In the surface vortex lattice method, both thrust and torque values agree with experimental values mostly, and this method is found to be accurate enough as a navigation element calculation tool when many panels are considered. 4 refs., 5 figs., 1 tab.

  15. Fiscal 1975 Sunshine Project research report. R and D on hydrogen production technology by high-temperature high- pressure water electrolysis; 1975 nendo koon koatsusui denkaiho ni yoru suiso seizo gijutsu no kenkyu kaihatsu seika hokokusho



    This report details the research result in fiscal 1975. Part 1 'Outlines' includes the research target, the summary of fiscal 1974 research results, the summary of fiscal 1975 research results, and responsible researchers. Part 2 'Details of the research' includes the fiscal 1975 research results. Chapter 1 reports 'Study on constant-load high- temperature high-pressure (multi-electrode type) diaphragm water electrolysis tank' promoted by Mitsubishi Kakoki Kaisha. Chapter 2 reports 'Study on Teflon system diaphragm for high-temperature high-pressure water electrolysis tanks' promoted by Yuasa Battery Co. through Mitsubishi Kakoki Kaisha. Chapter 3 reports 'Study on variable-load high- temperature high-pressure diaphragm water electrolysis tank' promoted by Showa Denko K.K. Chapter 4 reports 'The first detailed design of the electrolysis tank for a small test plant' promoted by Hitachi Zosen Corp. through Showa Denko K.K. Chapter 5 reports 'Research on the applicability of water electrolysis systems to various fields' promoted by Mitsubishi Research Institute, Inc. through Showa Denko K.K. (NEDO)

  16. Energy-saving by the optimization of the operation conditions in the vinylcloride lining steel pipe baking furnace. Enbirainingu kokan yakitsukero no sogyo joken saitekika ni yoru sho energy

    Kinoshita, Y. (Kawasaki Steel Corp., Tokyo (Japan))


    By the investigation of the operation conditions in the small experimental furnace, the improvement of the heat pattern of the steel pipes, and the remodeling and arrangement of the furnace, the progress of the yield and the productivity, and the reduction of the fuel unit were expected. In baking of a PVC pipe with a steel pipe, defects of PVC pipes as the blister of the inner surface occurred often. Accordingly the conditions when the blister occurred were investigated in the experimental furnace and optimized operation conditions when it does not occur were established. Next the flow rate of the hot air and the temperature distribution in the actual furnace were examined and the mechanism of occurrence of the defects of the blister of the inner surface was investigated. As a result, it was proved that the deviation of the hot air flux and the intrusion of the outer air cause it, and the places where the outer air intruded were closed by steel plates. After the improvements the rate of the defects of PVC pipes of the blister of the inner surface was decreased from 5% to 0.5%. Further, by the optimization of the operation conditions the fuel unit decreased and 31% of the rate of the energy-saving was achieved. The reduction of 10,414,000 yen a year was achieved. 29 figs., 4 tabs.

  17. Study on utilization of shallow sea areas by developing the alga field. Test for utilization of coal ash on alga reef (interim report); Sojo zosei ni yoru asakaiiki riyo no kenkyu. Sekitanbai kokabutsu no sosho riyo shiken (chukan hokoku)

    Tsuno, M.; Oikawa, M. [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Matsubara, T. [Hokkaido Area Management and Support Foundation, Sapporo (Japan)


    A development was intended of an alga reef block that is suitable for adherence of algae and difficult of shore-burning by utilizing coal ash. Concretes with different coal ash displacement rates were used to install alga reef blocks embedded with natural rocks, steel plates, and the used desulfurizing agents on three areas (the Usubetsu area, the Tamagawa offing, and Chatsu Bay) including shore-burned sea areas along the coast of Tomari Village. Investigations were made on the states of adherence of useful algae as a result of difference in materials and locations of installation. The best adherence of edible kelp was observed at the Usubetsu area, followed by the Tamagawa offing and Chatsu Bay in that order. Growth conditions of the kelp by locations were conceived of the correlation with how extensively the natural kelp colonies are formed around each location, and how many nutrient salts are present and sea urchins are grown. No remarkable difference was observed in the adherence of algae due to the difference in the coal ash displacement rates. Porous blocks, however, showed less adherence amount. Kelp adherence condition was found good in the order of concrete, natural rocks, and the used desulfurizing agents. No kelps have adhered on the steel plates. 10 refs., 13 figs., 3 tabs.

  18. FY1995 study of aid system for the elderly and the disabled using metal hydride alloy actuators; 1995 nendo suiso kyuzo gokingata actuator ni yoru kaijo shien system no kaihatsu



    Purpose of the project is to develop a transfer aid system for the elderly who need assistance in moving from a bed or a chair. It can make up insufficiency of assistant persons and can help to comfortably move the elderly. It has the highest demand in rehabilitation centers or hospitals. We have been designing an actuator using a metal hydride alloy for more than ten years and have confirmed that the actuator is very useful for developing the transfer. Furthermore, we have designed the transfer from a view point of human interfaces. This research was done under the above background. 1. We studied a comfortable posture for the elderly at an initial phase of standing to design the optimal knee pad using a life-size model of a transfer. Especially, we managed to lighten the burden imposed on the elderly by referring electromyographic signals at lower limbs and ground reaction forces. 2. Since the tactile sensation of the bottom of elderly person's foot gets dull, we designed a foot stage to prevent the elderly from the dull. 3. We determined the optimal mixture rate of a metal hydride alloy and developed an elastic bellows in order to design the actuator used for the transfer aid. 4. We determined the optimal compliance to prevent the elderly from a mechanical shock and designed a mechanism so that the transfer aid can work well. 5. Based on the above results, we developed the transfer aid using the metal hydride actuator. It was ascertained that it can lift a elderly person with 80kg weight by using only 40g alloy. Furthermore, it is proved that the transfer is not heavy (about 20g weight), small, silent, and moves smoothly by a battery on the market. (NEDO)

  19. Achievement report for fiscal 1974 on Sunshine Program. Research and development of hydrogen production technology using high-temperature and high-pressure water electrolysis; 1974 nendo koon koatsusui denkaiho ni yoru suiso seizo gijutsu no kenkyu kaihatsu



    The goals at present are to clarify conditions for the realization of the water electrolysis process relative to various primary energy sources and to experimentally construct a small practical electrobath to operate at high temperature and high pressure for the attainment of high economic efficiency. Efforts in this fiscal year are mentioned below. Surveys and studies are conducted about hydrogen production by water electrolysis and about achievements in the past and problems at present concerning hydrogen production by water electrolysis in Japan and overseas. The expected role of water electrolysis in various primary energy sources is also studied and evaluated. For a high-temperature high-pressure water electrolysis bath conceptual design (small test plant, bathing temperature 120 degrees C, pressure 20atm, hydrogen production rate 2Nm{sup 3}/h), studies are conducted about a constant-load type high-temperature high-pressure (bipolar) diaphragm-assisted water electrolysis bath and a variable-load type high-temperature high-pressure diaphragm-assisted water electrolysis bath. Surveys and studies are also conducted about the expected role of water electrolysis in various primary energy sources, and the role is evaluated. (NEDO)

  20. Research on mechanism of and catalysts for extraction liquefaction of coal using coal-based solvents; Sekitankei yozai ni yoru sekitan no chushutsu ekika kiko to shokubai no kenkyu



    Papers of Professor Yoshio Kamiya of Tokyo University are compiled into this report. The list of the papers includes (1) Synthesis of heavy fuel oils from coal; (2) Research and development of coal liquefaction; (3) Dissolution reaction of coal by hydrogen-donating aromatic solvents (I); (4) Effect of hydrogen-donor solvent on the liquefaction of coal; (5) Recent studies on the chemical structure of solvent refined coal; (6) Dissolution reaction of coal by hydrogen-donating aromatic solvents (II); (7) Future of coal as energy material; (8), (9), (10) same as (6) in the subject discussed; (11) Recent studies on coal liquefaction catalysts; (12) Environmental problems and drain treatment to accompany processes of converting fossil resources into fuels; (13) Chemistry of coal oxidation; (14) Fractionation and analysis of solvent refined coal by gel permeation chromatography; (15) Current state of research and development of coal liquefaction; (16) Properties and components of coal oils from coal liquefaction processes under development; (17) Solvent effect of coal derived aromatic compounds on the liquefaction of Akabira coal; (18) Chemistry of coal liquefaction; (19) Research and development of coal liquefaction in the U.S.; (20) Thermal treatment of coal-related aromatic ethers in tetralin solution; (21) Recent technology of utilizing heavy carbon resources; (22) Chemical properties and reactivity of coal; (23) Current state and future of development of coal liquefaction processes; and (24) Development of overseas coal liquefaction projects. (NEDO)