WorldWideScience

Sample records for kankyo sogo kansoku

  1. Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-06-01

    A high speed towed type physical and chemical observation marine robot named as `Flying Fish` has been developed since 1992, which can measure chemical substances in the sea as well as physical data, such as flow velocity of the ocean and water temperature. This paper describes its formation, designing, control system, and results of ocean tests. For the space continuous observation of physical, chemical, and biological quantities, it is essential to control the depth, pitch, and roll. The wing control method was employed for this robot. As a result of the ocean tests, the following conclusions were obtained. The accuracy under the steady state was {plus_minus}0.05 m in the depth, {plus_minus}1 degree in the pitch, and {plus_minus}0.5 degree in the roll. This was stable enough to operate chemical analysis, such as dissolved oxygen analysis. Even under the unsteady state during the change of depth, the pitch and roll were controlled in {plus_minus}3 degree and {plus_minus}0.5 degree, respectively. Results of the field tests and the numerical simulations for the performance of this robot were agreed well mutually in the practically sufficient accuracy. 10 refs., 15 figs., 2 tabs.

  2. Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-12-31

    With an objective for spatial continuous measurement of physical, chemical and biological amounts in ocean, development has been made on a wing controlled towed vehicle, `Flying Fish` which is capable of controlling depth, pitch and roll. Numerical simulations and two-year sea experiments have been carried out for the development. Flying Fish consists of a sub-system comprising a towing vehicle, towing cables, and on-board controllers. In a steady state, Flying Fish can be controlled at accuracy for depth of {plus_minus} 0.05m, pitch of {plus_minus} one degree, and roll of {plus_minus} 0.5 degree. This accuracy is sufficient for operating a chemical analyzer, the dissolved carbonic acid analyzer. Even in a non-steady state such as in changing the depth, the pitch can be controlled at {plus_minus} 3 degrees and the roll at {plus_minus} 0.5 degree. This extent of attitude change is within a range rendering no problems in maintaining accuracy of the measurement devices. The result of sea experiments for movements of Flying Fish agreed with that of the numerical simulation at practically usable accuracy. Flying Fish is verified as an effective system in investigating spatial variations in ocean data. 10 refs., 15 figs., 1 tab.

  3. Comprehensive research cooperation in environmental technology in fiscal 1995; 1995 nendo kankyo gijutsu sogo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Cooperative study was conducted on research subjects concerning water pollution preventive technologies in China and Thailand. In China, straw pulp mills were studied which were in the Institute of Light Industry Environmental Protection and the Environmental Engineering Course of Jinghua University. The following studies were jointly conducted: survey of the water quality pollution caused by waste water, investigational study on production technology and waste water treatment technology, extraction of technologies effective to preserve water quality, study/evaluation of economical efficiency of the said technologies, etc. In Thailand, cooperative research was conducted on automatic measuring technology for factory waste water in a model industrial estate of the Thai National Industrial Estate Corporation. Items for the study were a study on measuring technology for water quality environment, an investigation on the status of water quality environment in the model industrial estate, a study on automatic measuring technology for plant waste water, a study on how to use measuring data in the model industrial estate, etc. Every study enabled technical data accumulation at every research institute through field research exchanges. 24 refs., 91 figs., 45 tabs.

  4. Review of an analysis system of `Long-Term Deep Seafloor Observatory off Muroto Peninsula`; Kochiken Murotomisakioki `kaitei jishin sogo kansoku system` data no kaiseki system no shokai

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T; Machiyama, H; Hattori, M; Kaneda, Y [Japan Marine Science and Technology Center, Kanagawa (Japan)

    1997-10-22

    Introduced is a data analysis system for Long-Term Deep Seafloor Observatory established off Muroto Point by Japan Marine Science and Technology Center (JAMSTEC), from which observatory data collected by seismograph and tsunami-meter are transmitted real time. JAMSTEC Long-Term Deep Seafloor Observatory Project Team has begun constructing an analysis system for disposing of events in the data and for locating the hypocenter. The analysis system is composed of a data converting unit that converts the forwarded data into the Win format; a data storage/time-dependent data integration unit that keeps the data in a hard disk for a specified period of time, performs disposition and analysis of events in the data, and forwards the data after disposition and analysis to a data recording unit; a data recording unit that stores selected data of seismic events in a recording medium; and a real-time monitor/NTP server unit that displays real time the observed seismic waveform data. 2 figs.

  5. NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

  6. Fiscal 1993-1998 integrated research report. R and D on advanced combustion technology under microgravity environment; 1993 - 1998 nendo sogo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For developing advanced combustion technology by using JAMIC's facility, the advanced combustion technology research committee supported by researchers of universities, national institutes and industries was prepared in JSUP, and R and D using a microgravity experiment facility and the international joint research with NASA were carried out. By using the advanced experimental equipment and measuring instrument developed for microgravity experiments, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit and NO{sub x} generation mechanism, and such precious results were obtained as storage of abundant experimental data, explication of a combustion mechanism, preparation of a database and find of new phenomena. In the ground verification experiment using the newly fabricated advanced combustor test equipment, various data effective for developing high-efficiency low-pollution combustors were obtained. Through the joint research with NASA including 5 themes, various results and the real relationship between the researchers were also obtained. (NEDO)

  7. Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

  8. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

  9. Research report for fiscal 1998. Comprehensive research cooperation on environmental technologies (study of air pollution monitoring at model industrial estate in Thailand); 1998 nendo chosa hokokusho. Kankyo gijutsu sogo kenkyu kyoryoku (Taikoku model kogyo danchi taiki osen monitoring ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Cooperative studies are conducted for the improvement of technologies for preventing air pollution caused by SOx, NOx, volatile organic compounds, etc., discharged into the air by mills and factories. For the measurement of air pollution, instruments capable of automatic and uninterrupted measurement of SOx, NOx, and suspended particle matters are installed at Map Ta Phut Industrial Estate, and measurement is carried out. Volatile organic compounds are measured and analyzed along the borderline enclosing the estate. The amounts of SOx and NOx emitted by automobiles, ships, etc., are calculated. An air pollutant diffusion simulating model is built, into which data about pollution sources and weather are inputted for the calculation of SOx and NOx concentration levels at the industrial estate as is. Technologies are transferred to Thai researchers and engineers, which involve the use of instruments for the measurement of pollution levels in the environment and for the observation of weather conditions, the techniques of sampling and analysis, the construction of atmosphere simulating models, and the analysis and evaluation of the existing air pollution. (NEDO)

  10. FY 1999 report on the results of the study of the generative utilization basement technology of environmental friendly type metal base materials. Element/comprehensive process study; 1999 nendo kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu seika hokokusho. Yoso sogo process kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D have been conducted since FY 1991 on the process in which scraps can be used with no reduction energy required in iron-making stage, and the results of FY 1999, the final fiscal year, were summarized. In the assessment study of the comprehensive system, a full scale of experiment was carried out of the experimental plant which was completed in March 1998. In this fiscal year, experiment was conducted on converter type and fixed bed type as preheating/melting method. As a result, the energy unit requirement, productivity, etc. which were targeted at first were obtained, and the experimental results expected at first were obtained on scrap preheating/melting technology/exhaust gas treatment. Moreover, the FS using the actual system was conducted, and the following conclusions were acquired: melting use primary energy decreased by more than 25% from that in the existing electric furnace; it is possible to arbitrarily select power loads at 80%-30% the same as those in the existing furnace; new melting method is more excellent in primary energy reduction than in advanced electric furnace as of FY 1999; it is possible to reduce primary energy by 25% also in the case of operating iron-melting in converter type and shaft type. (NEDO)

  11. FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

  12. FY 2000 research cooperation project on the comprehensive research cooperation for environmental technology. Research cooperation for technology for prevention of the water pollution caused by plant waste water in Vietnam; 2000 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku (Betonamu koku kojo haisui ni yoru suishitsu osen boshi taisaku gijutsu ni kansuru kenkyu hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of increasing the research capability of the Center for Consultancy, Training and Technology Transfer in Vietnam, research cooperation for prevention of water pollution was given for plants of the local industry located in the suburbs of Hanoi city. In the survey of the actual state of the water pollution in the industrial area in the suburbs of Hanoi city, the following was found out: In the area, approximately 110 companies of the production industry such as livestock feed, papermaking, dyeing, brewing, construction materials, etc. are in operation and are discharging the untreated waste water into rivers and waterways because waste water treatment facilities are not prepared yet. In this research cooperation, the following were carried out: detailed survey of specified plants and proposal for improvement, training of Vietnamese researchers/engineers in charge of water pollution prevention technology, invitation to/training at Japan of Vietnamese managers/researchers, seminar to be held on the site, equipment to be given that is needed to measure water quality. The equipment to be given is a portable multi-item water quality meter and analytical equipment such as spectrometer, atomic absorption spectrophotometer and gas chromatograph. (NEDO)

  13. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

  14. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  15. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  16. FY 2001 report on the integrated evaluation of the research cooperation project. Research cooperation program on the development of environmental measurement use laser radar/research cooperation project on the mining waste water treatment technology using biology; 2001 nendo kenkyu kyoryoku jigyo sogo hyoka hokokusho. Kankyo kesokuyo reza reda no kaihatsu ni kansuru kenkyu kyoryoku - Baio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    By research groups having been sent, the integrated evaluation was made of the projects on the research cooperation with Indonesia in the development of environmental measurement use laser radar and the research cooperation with China in the mining waste water treatment technology using biology. As to the research cooperation with Indonesia, the purpose/target proposed were almost achieved, and all were favorably carried out. Especially, after finishing the project, the design/manufacture of an on-vehicle type Mie-scattering laser radar were made using the acquired laser technology. And, it was reported that an observation study of the state of air pollution in Bandung city was made using the laser radar. It can be said that generally the research cooperation with China was smoothly proceeded with. However, the Wushan mine is small in scale of management, and therefore, there might have been some points to be reviewed in selection of the mine for research. The pilot plant installed at the Wushan mine is not now operated. If the mine has strong management force, the effective use of the pilot plant after finishing the project might have been studied. (NEDO)

  17. Study of natural energy system and downward atmospheric radiation. Part 1. Outline on measurement and result on downward atmospheric radiation; Shizen energy system to tenku hosharyo no kansoku kenkyu. 1. Kisho kansoku gaiyo to tenku hosharyo no kansoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, K [Kogakuin University, Tokyo (Japan); Masuoka, Y [Yokogawa Architects and Engineers, Inc., Tokyo (Japan)

    1996-10-27

    For the study of a natural energy system taking advantage of radiation cooling, a simplified method for estimating downward atmospheric radiation quantities was examined, using observation records supplied from Hachioji City, Aerological Observatory in Tsukuba City, and four other locations. Downward atmospheric radiation quantities are closely related to partial vapor pressure in the atmosphere. Because partial vapor pressure changes according to the season, it was classified into two, for summer and for winter, and was referred to downward atmospheric radiation quantities for the establishment of their correlationships. Downward atmospheric radiation quantities were predicted on the basis of meteorological factors such as partial vapor pressure and free air temperature. Accuracy was examined of the simplified estimation equation for downward atmospheric radiation that had been proposed. A multiple regression analysis was carried out for calculating constants for the estimation equation, using partial vapor pressure, Stefan-Boltzmann constant, and free air dry-bulb absolute temperature, all closely correlated with atmospheric downward radiation quantities. Accuracy improved by time-based classification. At night, use of SAT (equivalent free air temperature) produced more accurate estimation. Though dependent upon local characteristics of the observation spot, the estimation equation works effectively. 10 refs., 10 figs., 3 tabs.

  18. Environment laws and regulations in China; Chugoku no kankyo hoki oyobi kankyo haishutsu kijun

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, K.

    1996-01-10

    The water environmental criteria in China consist of the sea water criteria, surface water criteria, fishery water criteria, agricultural water criteria, and scenery and recreational water criteria. This paper describes the problems thereof and the future assignments. The `sea water criteria` among other classifications of the water environmental criteria are under discussions for amendment that plan to increase the kinds of water from three in the conventional criteria to four kinds. Generation of harmful chemical substances has kept on decreasing since the 1980`s. However, as can be seen in part of the river water monitoring data, concentrations of pollutants show a trend of increase since 1994. This is caused by waste waters discharged from small-size chemical factories and hide tanning factories. Adequate regulations are applied to these `local enterprises`. Organic compound substances regulated under the waste water criteria are only seven kinds. As the kinds and amount of harmful chemical substances are anticipated to increase in the future, regulations that can deal with the new situation are required. Improvements are sought in the system of `discharge and contamination fee` imposed on industrial waste waters. Preparing the criteria for a total quantity regulation is an important assignment to be discussed as the forthcoming problem. 5 refs., 4 tabs.

  19. Arkitektur

    DEFF Research Database (Denmark)

    Kural, René

    2006-01-01

    Hanamadori Bunka Center , "Kulturcentret for blomster og grønt". Designet af Toyo Ito i samarbejde med bla. Kuwahara, Kanebako, Kankyo Engineering og Atelier Bow-Wow.......Hanamadori Bunka Center , "Kulturcentret for blomster og grønt". Designet af Toyo Ito i samarbejde med bla. Kuwahara, Kanebako, Kankyo Engineering og Atelier Bow-Wow....

  20. Fiscal 1997 achievement report. Research and development of comprehensive basic technology on marine resources; Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu sogo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The deep-sea manganese nodule mining system in this report collects efficiently and continuously a large quantity of manganese nodules in existence in the 5,000m-deep sea floor. The aim of the project is to develop and build an experimental system for a real mining machine and to perform a comprehensive marine test to find out if such a real machine is technologically and economically feasible. The system under this project is divided into four systems, which are a nodule mining system, nodule lifting system, nodule handling system, and a measurement control system. The nodule mining system travels on the sea bottom efficiently collecting manganese nodules and forwarding them into the nodule lifting system. Only a few systems of this kind have so far been developed, however, and therefore much endeavor needs to be exerted for the development of technologies involved. The nodule lifting system is divided into a pump lift unit, air lift unit, and a nodule lifting pipe. The pump lift unit and air lift unit elevate manganese nodules supplied from the nodule collecting unit to the sea surface. The nodule lifting pipe provides a passage for nodules to run through upward. (NEDO)

  1. History of global environmental problems. Chikyu kankyo mondai no rekishi

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, S [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1994-04-15

    This paper takes general view of the history of global environmental problems. A UN human environment conference was held in Stockholm in 1972, at which the human environment declaration and an action plan were adopted. The most important among the results of the Stockholm Conference were the treaty on international transactions of wild animal and plant species feared of extinction in the 1970's, the international treaty on prevention of pollution caused by ocean vessels, and the treaty on prevention of ocean pollution caused by dumping of wastes and other materials. Also adopted in the 1970's include the action plan to prevent desertification, the action plan on the world population, and the world weather plan. The UN Nairobi Conference in 1982 has sounded the alarm on the delay in tackling with the facing problems and the progress of aggravation in the global environment. In 1987, the ozone layer protection protocol was adopted. The earth summit at Rio de Janeiro in 1992 adopted the Agenda 21, with which the participating nations, autonomous bodies, and civil organizations have prepared their own Agenda 21, and are now about to begin challenging the global environmental problems. 7 refs., 4 tabs.

  2. Changing project finance climate; Project finance wo meguru kankyo henka

    Energy Technology Data Exchange (ETDEWEB)

    Madono, S. [The Export-Import Bank of Japan, Tokyo (Japan)

    1998-03-01

    Development of conditions under which project financing (PF) functions is described. PF, a method with which funds are procured for a project on the security of the assets of and the cash flow involving the project, established its position as a popular financial means. Into the 1990, however, PF underwent a complete change, when it came to be actively employed as a means for the procurement of money for what is called `infrastructure building project for invigorating the private sector` in the developing countries. PF has now come to be utilized for the financing of projects in various fields besides the field of resources exploitation. In particular, PF is now utilized in schemes such as BOT (build, operate, transfer) in public enterprises, for instance, electric power utilities in developing countries. The gravest problem found in the private sector invigorating type PF is that the sponsor, operator, exporter, and lender on their respective levels are experiencing rising risks because of intensified competition in the presence of a great number of projects. Such risks involve the exchange rate, the completion of work, and the relations between the borrower and operator. 2 figs.

  3. Environmental health surveillance system; Kankyo hoken surveillance system

    Energy Technology Data Exchange (ETDEWEB)

    Ono, M. [National Inst. for Environmental Studies, Tsukuba (Japan)

    1998-02-01

    The Central Environmental Pollution Prevention Council pointed out the necessity to establish an environmental health surveillance system (hereinafter referred to as System) in its report `on the first type district specified by the Environmental Pollution Caused Health Damages Compensation Act,` issued in 1986. A study team, established in Environment Agency, has been discussing to establish System since 1986. This paper outlines System, and some of the pilot surveillance results. It is not aimed at elucidation of the cause-effect relationships between health and air pollution but at discovery of problems, in which the above relationships in a district population are monitored periodically and continuously from long-term and prospective viewpoints, in order to help take necessary measures in the early stage. System is now collecting the data of the chronic obstructive lung diseases on a nation-wide scale through health examinations of 3-year-old and preschool children and daily air pollution monitoring. 6 refs., 3 figs., 1 tab.

  4. Environment purification using microorganisms. Biseibutsu ni yoru kankyo joka

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H [Asahi Glass Co. Ltd., Tokyo (Japan); Harada, S

    1993-12-01

    Technologies to purify polluted soils vary with kinds of pollutants, spread of pollution, and shapes of water veins. A method is used often that several wells are drilled in a polluted area, and water is circulated between upstream wells and downstream wells, where activities of microorganisms living in that particular environment are utilized to biodegrade the pollutants. This technology is called bioremediation. This paper deals with soil pollution by chemical substances, and describes development of a technology to remove pollution caused by PCB and petroleum which is thought difficult to apply the bioremediation technology among environment purifying technologies using microorganisms. The bioremediation of petroleum pollution assumes petroleum pollution on seashores. Discussions have been given on separation from sea water of petroleum decomposing microorganisms to be used in the bioremediation, and the number of petroleum decomposing bacteria in seas near Japan. As a result, it was made clear that a few kinds of bacteria will suffice for decomposition of main components in a mixture as complex as petroleum. 5 refs., 4 figs.

  5. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  6. Cooperative measurements of microtremors in the north-eastern region of Nishinomiya city, Hyogo Pref.; Nishinomiyashi hokutobu ni okeru joji bido no godo kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Maiguma, T; Matsuzawa, H [Saitama University, Saitama (Japan). Faculty of Engineering; Sawada, Y; Tazawa, Y [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-05-01

    For the purpose of generally grasping space distribution of ground vibration characteristics, cooperative measurements were conducted in a wide area, mainly in the area stricken by the M7 earthquake. Forty-five organs such as governmental institutes, universities, and private company institutes participated in the measurements which were conducted at 1967 measuring points. The area which the author is in charge is an area from the north of Nishinomiya City to the south of Takarazuka City. The area is relatively far from the hypocenter area, but the magnitude is 7 there and damage was concentrated. The measurements were made by each independent team from August 29 to September 1, 1995. As a result of spectral measurements of NS, EW and UD components, conspicuous peaks were seen in an extent of 1.5 sec. cycle in almost all measuring points and components. Further, in spectra of horizontal motion components of A measuring point group, conspicuous peaks were seen in an extent of 0.15-0.5 sec. cycle, and in those in B and C measuring point groups, in an extent of 0.35-0.5 sec. cycle. In upper/lower motion components, conspicuous peaks were seen in an extent of 0.3 sec. cycle in A measuring point group. 4 figs.

  7. Magnetotelluric investigation in and around southern part of Hidaka metamorphic belt in Hokkaido, Japan; Hidaka henseitai nanbuiki ni okeru MT kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Sato, H; Utsugi, M; Hirano, K; Doi, T; Nishida, Y; Arita, K [Hokkaido University, Sapporo (Japan)

    1996-05-01

    An MT observation was conducted in the Hidaka district, Hokkaido, for the estimation of the 2D resistivity structure in the southern part of the metamorphic belt, when frequencies of the VLF, ELF, and ULF bands were used. An approximately 42km-long traverse line was set to cross the Hidaka metamorphic belt from east to west. As for the observation points, 48 VLF points, 16 ELF points, and 4 ULF points were provided. During the data processing, impedance tensor was calculated in the frequency domain for the determination of the apparent resistivity relative to frequency and the phase difference. As the result, it was found that there is a fairly large resistivity gap between observation spots MNS and KWR and that the boundary corresponds to the Hidaka metamorphic belt, that the metamorphic belt that is reflected as a conspicuous high-resistivity layer in the VLF-, ELF-MT slopes down toward the east and has a distribution as deep as 10km in the vicinity of observation point KWR, that this high-resistivity layer sandwiches a low-resistivity layer at a depth of 5-7km, and that on the east side of the metamorphic belt there is a medium-resistivity layer creeping under the belt from the east side toward the west side. 5 refs., 6 figs.

  8. Measurement of radiation and temperature of cathod spots in excimer laser discharge; Ekishima reza reiki hodennai ni fukumareru inkyoku kiten no kogakuteki kansoku to ondo no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Minamitani, Y.; Nakatani, H. [Mitsubishi Electric Corp., Tokyo (Japan)

    1996-08-20

    Excimer laser is used in various fields such as luminous source for steppers, annealing treatment, ablation process, nuclear fusion and so on. In this paper, the radiation timing and gas temperature of cathode spots, streamer discharges and glow discharges in KrF excimer are measured by observing the radiating spectra thereof. The following conclusions are obtained from the results of the present study. Cathode spots begin to radiate at about 20ns after the discharge initiation, then the first and second radiation peaks are observed respectively when the discharge current reversing after passing zero point and the reserved discharged current approaching zero point. Streamer discharge makes flashover between electrodes at the second radiation peak of cathode spots, while the glow discharges almost disappear when streamer discharges occurring. The temperatures of cathode spots and glow discharge as 5500K and 2600K respectively are almost constant and independent upon the discharging voltage of laser. 14 refs., 12 figs.

  9. Fiscal 1987 R and D of observation system for probing resources. 3/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper puts together the R and D of a sensor system and a data transmission system in the R and D of observation system for probing resources. In the studies of the on-satellite synthetic-aperture radar (SAR), reexamination was conducted on the basic design of the SAR system and its test plan; also conducted were the drafting of the combination test plan of an SAR/mission transmitter and the design/manufacturing of the machinery required for the test. In the studies of the on-satellite optical sensor, the research of the function/performance of an optical sensor system was carried out, as were the design/manufacturing of an engineering model and the design/model preparation of a visible near infrared radiometer, short-wave infrared radiometer, thermal controller, etc. In the R and D of the data transmission system, a mission recording device was manufactured and tested, with the electrical/mechanical performance confirmed. Further, as a result of the test of the mission transmitter antenna, it was found to fulfill the development specifications. (NEDO)

  10. Achievement report for fiscal 1984 describing research and development of earth resources observation systems; 1984 nendo shigen tansayo kansoku system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    Japan's Outline of Space Development were renewed in February 1984. Under the new principles, the earth resources satellite (ERS-1) program is to be promoted and that research and development efforts for a launch in fiscal 1989 are to be started. Industrial, academic, and governmental organizations concerned making their utmost efforts have established a Technology Research Association for Resources Remote Sensing for the execution of the tasks. The contents of its business are the research and development of an observation system to be installed aboard ERS-1. That is, a synthetic aperture radar and other equipment such as optical sensors and data transmission systems will be developed, and technologies necessary for the development of a satellite borne observation system will be established through evaluation and verification by testing such systems for instance aboard aircraft. Carried out in fiscal 1984 are the studies of required specifications and the drafting of research and development programs for the next and the following fiscal years involving the research and development of the resources exploration system as a whole, sensor systems, and data transmission systems. (NEDO)

  11. Development of deepsea geomagnetic and electric fields observation system using submarine cables. 2; Kaitei cable riyo no shinkai chijiki denba kansoku station no kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, T; Nakatsuka, T; Murakami, Y [Geological Survey of Japan, Tsukuba (Japan); Onishi, N

    1997-10-22

    VENUS Project aims at constructing a deepsea geomagnetic and electric fields observation station to cover the Ryukyu Trench, Philippine Sea, and Mariana Trough, by the reuse of the Okinawa-Guam commercial marine communication cable now out of service. This report deals with a scenario for the development of a geomagnetic/electric observation system as a part of the planned long-term sea bottom observation effort and the installation of equipment therefor. The first stage consists of the towing of a frame mounted with the system equipment and a cable to connect to a data transmission relay and their placement at a specified location on the sea bottom. The cable is extended toward the relay and its leading end is allowed to land near the relay. Next, a manned submersible vessel is used to connect the cable end to the relay, the submersible vessel is next driven along the connection cable toward the system equipment for the determination of the position and orientation of the system equipment, and then electrodes are arrayed at an interval of 20m into an L-letter configuration. The system will be established in March, 1998, on the 4200m-deep continental slope of the Ryukyu Trench approximately 90km southeast of Okinawa. 2 figs., 1 tab.

  12. Estimation of underground structures in Kyoto city by seismic-array observations of microtremors; Bido no array kansoku ni yoru Kyoto shinai no chika kozo tansa

    Energy Technology Data Exchange (ETDEWEB)

    Miyakoshi, K; Kagawa, T; Akazawa, T [Osaka Soil Test, Osaka (Japan); Ogawa, Y; Shimizu, K [Osaka Gas Corp., Osaka (Japan); Ejiri, J [Obayashi Corp., Tokyo (Japan)

    1997-10-22

    Observations of microtremors were carried out to estimate the S-wave velocity structure by using arrays of seismographs around the Kyoto Research Park. The observation points were so arranged that equilateral triangle arrays may be formed with maximum radii at 0.2 km, 0.4 km and 0.8 km respectively with the premises of the Kyoto Research Park as the center. The seismographs have used seven vertical movement components (PELS), and were adjusted to a period of eight seconds. In addition, high-cut filters of 4 Hz were used because the observation areas are located in urban areas with heavy traffic. The analysis has used the spatial self-correlation method as a means to estimate phase velocity of surface waves contained in microtremors. As a result, phase velocity estimation has become possible for frequencies from about 0.4 Hz to 2 Hz, whereas the S-wave velocity structure was estimated to a depth of down to about 900 m by using as reference the result of the reflection method exploration having been carried out in the present areas. In addition, it was suggested that microtremors with frequencies higher than 1 Hz are in unsteady state in terms of time or space. 4 refs., 7 figs., 1 tab.

  13. Fiscal 1987 R and D of observation system for probing resources. 2/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper puts together the studies of the system design and control technology and of the system design and evaluation technology concerning the R and D of observation system for probing resources. In the studies of the system design and control technology, conducted were the design/examination on the electrical, mechanical and thermal interfaces between the satellite body and a mission transmitter, as well as the examinations on the mounting position, environmental test conditions, etc., with results produced. Also conducted were the interface with the terrestrial station, operation mission analysis, etc. In the studies of the system design and evaluation technology, for the purpose of evaluating ERS-1 optical sensor specifications, experiments by aircraft were carried out which used on-aircraft imaging spectro radiometer, with evaluation performed by means of multi-channel image data so obtained. Further, in the aircraft/space shuttle experiments, examination was carried out on such items as an aircraft system concerning optical sensors, visible near infrared radiometer, short wave infrared radiometer, and on-satellite synthetic-aperture radar. (NEDO)

  14. Array measurements of long-period microtremors in southwestern Kanto plain, Japan; Kanto heiya nanseibu ni okeru yaya choshuki bido no array kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Yamanaka, H; Sato, H; Kurita, K; Seo, K [Tokyo Institute of Technology, Tokyo (Japan)

    1997-05-27

    Array measurements of long-period microtremors were carried out in the southwestern part of Kanto Plain, Japan, to obtain S-wave velocity structures in sedimentary beds as fundamental data for estimating long-term strong ground motion in Kanto Plain. The major component in a long-term seismic motion observed in Kanto Plain is the surface wave. According to the result of observations on Love wave by Kinoshita et al, the wavelengths of the surface waves of a long-term cycle are 10 to 20 km. Therefore, if an array observation is to be performed at intervals of about two wavelengths, about 40 points will be required to cover the entire Kanto plain. The final phase velocity is decided by averaging phase velocities of each cycle obtained for each data set. The acquired phase velocities are analyzed inversely by using a genetic algorithm to derive the S-wave velocities at each observation point. The present microtremor array observation has used 13 points in the southwestern part of Kanto Plain to acquire S-wave velocity (Vs) distribution in sedimentary beds. It was made clear that beds with Vs of 1.0 km/s and Vs of 1.5 km/s exist in this area between the surface bed and the seismic foundation with Vs of about 3 km/s. 10 refs., 10 figs., 1 tab.

  15. Observations and analysis of free groundwater levels and groundwater pressure in landslide slopes. Jisuberi shamen no jiyu chikasuii, chikasuiatsu no kansoku to kaiseki ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, S; Nakano, T [Niigata Univ., Niigata (Japan). Faculty of Agriculture; Inaba, K [Niigata Univ., Niigata (Japan). Graduate School; Sato, O [Niigata Univ., Niigata (Japan)

    1991-12-25

    It is well known that the landslides in Tertiary systems abundantly found in Niigata Prefecture, etc., frequently occur especially in the snow melting season or the heavy rain season. For studying the occurrence of such landslides, exploration of the actual condition of groundwater and evaluation of the strength of earth are very important even when the landslide occurring mechanism can be presumed in a relatively simple way about the soil mechanics. Therefore, great importance is attached to the observation and investigation on the groundwater level and pressure at landslide sites and stability analyses have been actively performed. However, it is considered that several fundamental problems still exist in the method for estimating the groundwater level and pressure in landslide slopes from the observation method and data on groundwater levels and pressure (pore pressure). In this paper, these fundamental problems are examined on the basis of concrete observations made by the writers on landslide slopes at Matunoyamagoe and Higashimusikame landslide sites in Niigata Prefecture for the past several years. 6 ref., 6 figs., 2 tabs.

  16. Analysis of vibration characteristics of a prestressed concrete cable-stayed bridge using strong motion observation data. Jishin kansoku ni motozuku PC shachokyo no shindo tokusei no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Inatomi, T. (Port and Harbour Research Institute, Kanagawa (Japan)); Takeda, T.; Obi, N.; Yamanobe, S. (Kajima Corp., Tokyo (Japan))

    1994-05-31

    Records of seismic observation were analyzed for the purpose of proving the validity of antiseismic design for a prestressed concrete (PC) cable-stayed bridge. This bridge is a three span continuous PC cable-stayed bridge of 498 m in bridge length, and is constructed on alluvial soft ground. The seismometer used is a servo type accelerometer. The observed frequency and mode of seismic vibration are in good agreement with those in the analysis and hence the validity of modelling of the structure in designing was confirmed. It was also confirmed that the bending vibration and torsional vibration of the main girder are separated as designed. However, some points such as a large difference in the observed vibration and analysed vibration in the mode accompanying rotation of the base are listed as problems to be solved in antiseismic design. In order to investigate the attenuation constant of the upper structure, a seismic wave response analysis was performed and its results were compared with observed ones. When the attenuation constant is assumed to be 2%, agreement of data between analysis and observation is good, and it is considered that the attenuation constant of the upper structure only without the effects of attenuation of energy escape from the base and crack generation in concrete was about 2% in the observed earthquake (maximum acceleration on the ground: 51 Gal). 8 refs., 9 figs., 2 tabs.

  17. Exciting test of a floating type cable stayed bridge and its response observation under the typhoon; Furotiingu keishiki shachokyo (Utagenkabashi) no kishinki shiken to taifuji oto kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Uno, K. [Kyushu Kyoritsu Univ., Kitakyushu (Japan). Faculty of Engineering; Aso, T. [Yamaguchi Univ., Ube (Japan). Faculty of Engineering; Kitagawa, S. [Kyushu International Univ., Kitakyushu (Japan). Faculty of Economy; Kabashima, S.

    1995-09-20

    Recently, in case of the planning and designing of bridges, of course its practicality and execution stability are considered, but consideration for landscape also is a large problem. In particular, the selection of the bridge type is very important in order to protect the beautiful natural landscape. The cable stayed bridge has become to be executed often, owing to its elegant style, however, it becomes important theme clarify the antiseismic and wind stability because of its complicated structure system and very slender girder. In this paper, the results of the dynamic characteristics of a floating type cable stayed bridge (length 292.1 m and width 14.9 m) and the observation of its dynamic behavior under the typhoon are reported. Microtremor measurement was performed to determine the dynamic characteristics of the bridge under construction. After the construction of the bridge, the excitation test was carried out in order to confirm its natural frequencies, vibration modes and damping constants. From the results of the observation of the dynamic behavior of the girder and cables under the typhoon, the wind stability of this bridge was confirmed. 10 refs., 13 figs., 9 tabs.

  18. Trend survey of the global environment adaptation type industrial technology. Chikyu kankyo tekiogata sangyo gijutsu doko chosa. ; Chikyu kankyo kanren kenkyu doko no chosa (nisanka tanso no kankyo fuka teigensaku ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The paper studies the measures for reduction of environmental load of CO2 from the standpoint of chemical technology. As for methanol synthesis from CO2, accelerating of the reaction using Cu base compound catalyst is reported. Also, CO2 is methanated at high speed by low temperature waste heat using Ni-La2O3-Ru catalyst. Discussions are given on the subject for development of catalyst reaction relating to hydrogen production technology by methane reforming reaction using steam or CO2. Synthesis of polymetric materials by use of CO2 is also described. The paper mentions that it is indispensable to design high-function electrode and elucidate the reaction mechanism of electrochemical CO2 reduction for electrochemical and photochemical CO2 reduction measures. Moreover, in case of using solar energy, it is required to study photovoltaic excitation process in semiconductor electrode/ electrolyte solution interface. For production of hydrogen from CO2 by photosynthetic organisms and solar energy, the problem is control of inhibiting effect of oxygen combinedly produced. Described are production of polyhydroxy butyric acid and biodegradable polymer from CO2 and hydrogen by bacteria, and CO2 fixation imitating the enzyme reaction. 267 refs., 79 figs., 32 tabs.

  19. Interactions between wall rocks around magma and hot water. Magma shuhen no hekigan/nessui sogo sayo

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, K.

    1992-12-01

    This paper describes interactions between wall rocks around magma and hot water. The paper discusses effects of hydrothermal environments on dynamic properties of rock minerals with respect to hydrolytic weakening (decrease in dynamic strength of a mineral under presence of water) and reaction enhanced deformation (deformation accelerated by chemical change occurring in a mineral itself). It also explains chemical reactivity of minerals under hydrothermal enviroments with respect to four types of chemical changes in minerals, factors governing mineral dissolution rates, and importance of equilibrium and non-equilibrium in main components in reactions between minerals and waters. These statements quote mainly results of indoor experiments. The paper indicates the following matters as problems to be discussed on interactions between wall rocks around intrusive rocks and hot waters: Deviation from chemical equilibrium in reactions between rocks and waters; change in permeability as a result of reactions between rocks and waters; and possibilities of hydrolytic weakening in rocks around intrusive rock bodies. 52 refs., 6 figs.

  20. Report on a comprehensive research study (home welfare apparatus system - lifestyle); Sogo chosa kenkyu (zaitaku fukushi kiki system - lifestyle) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted on evacuation of aged people at disaster, life maintenance, and welfare apparatus which is applicable to the future change of life style and its harmony with the living environment. In the study of care apparatus, reported were the apparatus operational interface using the indoor environmental control simulation system, safety on moving/transfer equipment, experiment on opening/closing power of sliding doors, study of electric-driven wheel chairs, study of the sitting pressure of various wheel chairs, etc. In relation to the living environment, the paper reported planning of houses introducing care apparatus, assessment of system kitchen, disaster prevention measures for aged/handicapped people, study on performance of the combined use in the living environment, assessment of drops in floor level in the living space, etc. Also reported were assessment on the living environmental control state of serious paralyzers of the limbs, study of a network to support care at home, etc. 48 refs., 117 figs., 29 tabs.

  1. Report on the comprehensive investigational research (at-home welfare apparatus system); Sogo chosa kenkyu (zaitaku fukushi kiki system) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was conducted on the research and development of an at-home welfare apparatus system. In this study, a stay experiment was carried out on whether aged or handicapped people can easily live in welfare houses into which at-home welfare apparatus was integrated, using high-tech at-home nursing apparatus systems (welfare techno house: WTH) which were installed at seven places in Japan based on `the development of a system supporting independent excretion.` In addition, the following were conducted: experiments on at-home welfare apparatus in terms of the evaluation of performance/operability/safety, physical physiology reactions, nursing burden/estimate of independence, two-way communication, examination of housing environments, etc. In WTH Chofu, a test on evaluating welfare apparatus was conducted by people with limbs paralysis and healthy case workers. In WTH Sapporo, by a working group studying biological information, examinations were made on the situation of standing up of healthy adults, old people and people with paralysis of one side of the body from various types of chairs, beds, wheel chairs, portable toilets and sitting down on them. An examination was also made on harmony with psychological function and physically adaptable function by a working group studying at-home nursing apparatus. 75 figs., 15 tabs.

  2. Report on a comprehensive research study (home welfare apparatus system - interface); Sogo chosa kenkyu (zaitaku fukushi kiki system - interface) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the light of the increasing role of welfare at home with the advance of the aging society, the paper conducted an investigational study on the R and D of the home welfare apparatus system - interface. In the study, making the most of the leading home care apparatus systems (welfare technohouses) installed at seven places in the country, the paper carried out a stay experiment on how the life is in the welfare house into which home welfare apparatus is integrated, and an experiment to assess biological data on aged people. Especially as to the support apparatus used for smooth life motions in houses such as movement, excretion and bathing, examined were the linkage with house bodies, care apparatus used, mutual interface with welfare apparatus, etc. By the experiments to assess these home welfare apparatus, an analytical study was conducted on the points to be improved in welfare apparatus and housing equipment, and at the same time on the course of the research/development. Concerning a system for the research study, a research promotion committee was established in Technology Research Association of Medical and Welfare Apparatus, the members of which are learned persons from the industrial circle, the government and universities. 111 figs., 36 tabs.

  3. Report on survey in fiscal 1999. Comprehensive survey on medical appliances; 1999 nendo iryo kiki sogo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The environment around medical treatment in Japan is changing greatly in recent years, because of aging of the population, increase in life habit diseases, and progress in medical science and technologies. In addition, the needs of people are on the trend of diversification. Furthermore, as a result of the information communication field gaining remarkable power, people can obtain information in various forms, and are acquiring chances of learning various kinds of knowledge about medical treatment. Thus, scenes to respond to demands of patients are increasing more than ever in medical activities. On the other hand, works and conversion in providing efficient medical services are sought because of pressures on medical finance. Therefore, the 'medical and welfare device development project' was launched in fiscal 1994, wherein NEDO has been promoting the research and development jointly with private business entities. In fiscal 1999, assignments in important technologies will be made clear taking the future into the sight on three themes in two fields of developing low invasive operation systems, and comprehensively developing artificial organ technologies. Themes to be developed newly in the future will be selected, and the contents of the research and development thereon and the ways it should be will be investigated, evaluated and discussed specifically. (NEDO)

  4. Microalgal biotechnologies for recycling of pollutants; Tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangata sogo saishigenka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, K; Nasu, M; Hashimoto, C; Tanaka, K; Hirata, M [Osaka University, Osaka (Japan). Faculty of Pharmaceutial Science; Fujita, M; Takagi, M [Osaka University, Osaka (Japan). Faculty of Engineering; Hirata, Y; Taya, M [Osaka University, Osaka (Japan). Faculty of Engineering Science; Yamanishi, H [Osaka University, Osaka (Japan). Faculty of Medicine

    1997-02-01

    This paper describes the technology development by which biomass is produced by treatment of pollutants using microalgae, and is recycled. A bioreactor system has been developed, in which microalgal biomass can be obtained through the effective treatment of CO2 and NOx using microalgae having ability of increase under the severe condition with simultaneous flow of CO2 and NOx. A new method has been also developed for separating and recovering the microalgae. Materials, such as glucose, glycerol, acetic acid, and lactic acid, were produced from the obtained biomass through physico-chemical and biological treatments. These materials can be converted into ethanol and hydrogen. For this treatment and recycling system, functions as a part of natural material recycling were considered to be most significant. Development of an analysis and evaluation method of an impact of this system on the natural environment is also tried. 1 fig.

  5. Research cooperation in the development of laser radar for environmental measurements. Environmental network; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku. Kankyo network

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Among the research cooperation in the development of laser radar for environmental measurements with Indonesia between FY 1993 and FY 1996, results of the research and development of the environmental network are summarized. For the environmental information network, the Tokyo NOC is linked as an Internet connection point in Japan with the Jakarta NOC using an international dedicated line with a capacity of 64 Kbps. The Tokyo NOC is linked with domestic environmental information researchers using Internet. Thus, data stored in the data processing system of laser radar can be exchanged, information in both countries can be exchanged using E-mail, and data can be accumulated. For the research cooperation with Indonesia, research of path control and information relay server, research of effective transmission of data on the network, and research of multimedia communication have been conducted. The multimedia communication, distributed processing, and extension of dedicated line network using PPTP have been also conducted. 39 figs., 4 tabs.

  6. Research and development cooperation project on environmental measurement using laser radar (environmental network) in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of contributing to the research cooperation project on the development of a laser radar for environmental measurement, the paper surveyed the present and future trend of the environment related information network in Indonesia. The survey was conducted in terms of a name of the network, the main administration body, the number of users, the utilization status, the use protocol, details of service, domestic mode installation sites and the main administration body, accounting system, types of the network used, reliability and stability of network, limitations on the use and details of the limitation, etc. The plan for expanding telecommunication equipment is being advanced in a very quick tempo. However, there are many problems in digitalization, and it is feared that the plan will be delayed. As to telecommunication quality and connection quality, the telecommunication completion rate, SCR, is very low, approximately 24% on average, which is equal to that around 1990 in Japan. The business service for users is all bureaucratic since they have a lot of applications for the installation piling up with no exception to the rule of developing countries. 23 figs., 10 tabs.

  7. Research and development cooperation project on environmental measurement using laser radar in fiscal 1995 (environmental network); Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the cooperative work with Indonesia of R and D of a laser radar for environmental measurement, the paper described the development of an environmental network. The field survey was conducted in April, July and December 1995 and in March 1996. For the investigational research, five meetings of the committee and four times of group work were held. The Asian environmental network was studied in terms of its arrangement, operation and management, and the overall network/path control design were being prepared. To make the persons concerned abroad and in Japan understood the APEC Osaka Conference held in November 1995, a homepage APEC `95 Kansai was opened using WWW (World Wide Web, a decentralized hyper media system which can dispatch information to the whole world by network using hyper text). Moreover, in connection with this, a homepage was opened of CICC (Center of the International Cooperation for Computerization, a center controlling the whole Asian environmental information network system where E-mail and data are exchangeable with Indonesia via Tokyo NOC (Network Operation Center)). 49 figs., 8 tabs.

  8. Environment of developing countries. ; Centered around 1992 white paper or environment. Kaihatsu tojokoku no kankyo. ; 1992 nenban kankyo hakusho wo chushin ni shite

    Energy Technology Data Exchange (ETDEWEB)

    Takiguchi, N [Environment Agency, Tokyo (Japan)

    1992-12-01

    The present paper outlines the present situation of environment of developing countries, factors causing environmental devastation, and the influence in the international linkage as described in 1992 White Paper on Environment. The present environmental devastation is originated from national poverty. In general, as the results of imposing excessive pressure on the natural environment accompanying the increase of population or causing urban pollution due to the movement or densification of population, poverty brings about the reduction and devastation of forest, deterioration of soil, desertification, contamination of air and rivers, causing miserable situation. Prawn culture as primary export industry damages mangrove woods, and causes water pollution. Industrial development is rapidly spreading pollution of water and air. As for international relations, the net transfer amount of money in the flow of funds between advanced countries and developing countries is in the direction from the latter to the former due to payment of debts. In enforcing direct investment or overseas development aid projects, advanced countries must be aware of their responsibility, make efforts in grasping the situations of aided countries and perform sufficient environmental assessment. 5 refs., 8 figs., 11 tabs.

  9. Research and development cooperation project on environmental measurement using laser radar in fiscal 1994 (environmental network); Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Under the R and D of a laser radar for environmental measurement which are conducted in cooperation with Indonesia, the paper reported the R and D of the environmental network in fiscal 1994. Four field surveys were made, and the following were conducted: proposal of a technical system, adjustment of the Asian environmental information network with BPPT and LIPI which are organs on the Indonesian side, installation of/technical discussion on network equipment, etc. There is IPTEKNET as a plan of a nationwide network of the scientific technology information service in Indonesia. The analytical design phase of this system converged in 1992, and the predicted investment amount in the coming five years is expected to be 6.7 million US dollars. As the future Asian environmental information network work, planned are connection between BPPT and Tokyo CC and connection at BPPT between the Asian environmental information network and IPTEKNET. Network managers at sites are very skillful, and therefore, the thorough cooperative work is anticipated. 24 figs.

  10. Global environment protection from the universe. Uchuu yori no chikyu kankyo hogo

    Energy Technology Data Exchange (ETDEWEB)

    Iwasaki, N. (National Space Development Agency of Japan NASDA, Tokyo (Japan))

    1994-06-15

    Two articles of 'Care of coppice in Wood Totoro' and 'Global environment protection from the universe' are included in this report. The former explains the necessity of coppice conservation through an example of Sayama Hill in Tokyo. Until the time 30 years ago, coppices are deeply related to people as the places which supply fuel and fertilizer to villagers, but they have been left or cut down by energy source conversion and development of home lots. Now we must learn the traditional methods of caring coppices again and find a new sense of values regarding the nature. The latter introduces satellite-used remote sensing which allows to continuously scan all the areas of the earth within a short period for global environment protection. This sensor uses a wide range of wavelengths from light to radiowave. In the U.S., it is operated in the name of LANDSAT since 1972, and Japan is also operating various kinds of satellites for environment research concerning, e.g., CO2 concentration and resource exploration. 10 figs.

  11. Air environment purification using photocatalyst. Hikari shokubai ni yoru taiki kankyo joka

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, K [National Institute for Resources and Environment, Tsukuba (Japan)

    1993-12-02

    Noticing that metal oxides have photocatalysis for reduction in NOx concentration and examining effects of the TiO2 selected on removal of pollutant, the paper proposes a direct purification method for the air environment. Since TiO2 causes electron excitation meeting near ultraviolet irradiation, it manifests a catalytic function for various oxidation/reduction reactions. Details of the reaction mechanism are unknown, various active oxygen species generated on the surface of TiO2 under light irradiation oxidize NOx and acquire it as nitric acid on the surface. It is found that mixture of activated carbon of low hygroscopicity with TiO2 is effective to prevent a tendency of NO to desorb before NO becomes nitric acid. What 40% of the catalyst with fluorine resin is formed into like a sheet shows a high removal rate even in the amount of ultraviolet irradiation in a winter cloudy day in the wide range of 0.5 - 95.0% of NOx and SO2, and if the photocatalyst is applied to the side wall of city buildings, the NOx concentration is estimated to be reduced by as much as 20%. 5 refs., 3 figs.

  12. Micrometeorological function of paddy fields that control temperature conditions; Suiden no ondo kankyo kanwa kino

    Energy Technology Data Exchange (ETDEWEB)

    Oue, H; Fukushima, T [Ehime University, Ehime (Japan). Faculty of Agriculture; Maruyama, T [Kyoto University, Kyoto (Japan). Faculty of Agriculture

    1994-10-01

    A verification was conducted on the micrometeorological function of paddy fields that control temperature conditions. A movement measurement was executed in order to elucidate air temperature distribution in the paddy field area. The observation revealed the following matters: air temperatures over paddy fields and farm lands are lower than those at bare lands and paved areas; air temperatures downwind the paddy fields are lower than those in residential areas; and air temperatures on the paddy fields are lower than those on the farm lands. Measurement of the air temperature distribution in paddy fields revealed that a paddy field becomes a heat absorbing source in the process of breeze blowing over the paddy field, and alleviates the temperature environment in the downwind area. A discussion was given on the specificity of surface temperature of the paddy field from the above result. It is the feature of paddy fields in summer that the energy exceeding the radiated amount is distributed into latent heat around the noon of a day. The surface temperatures are in the decreasing order of non-irrigated bare land > irrigated bare land > atmometer water surface > farm land > paddy field. The upper limit for the paddy field surface was around 28{degree}C. Surface temperature forming factors were discussed, and the surface temperature parameters (relative humidity, evaporation efficiency, etc.) were derived on each type of the land surface. The surface temperatures on each land surface were calculated using the parameter values. The result revealed that a paddy field having high relative humidity and evaporation efficiency has an effect to suppress the surface temperatures. 6 refs., 10 figs., 1 tab.

  13. Evaluation of environmental impact by LCA method. LCA shuho ni yoru kankyo fuka hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Sakamura, H.; Utsuno, F.; Yasui, I. (The University of Tokyo, Tokyo (Japan). Institute of Industrial Science)

    1994-06-01

    This paper explains the concept, history, and analytic methods of life cycle assessment (LCA), showing its application to beer bottles and cement factories as specific examples. The LCA is a method to calculate substances and energies put into the whole process of production of a product from raw material mining to product wasting and environmental loads emitted therefrom. It also evaluates the result collectively and quantitatively. A first case of the research is reportedly the one performed at Coca-Cola Co., Ltd. in 1969. Full-scale researches have gone forward in European countries in the recent several years, and are progressing to international networks. The analytic methods can be divided largely into an accumulation method to analyze data in each process and add them up, and a method to use an industrial association table. The former method is the most generally used method currently in overseas countries if referred to the LCA. Because the LCA can cause the analytic result and evaluation to vary depending on the purpose, it is important to define the goal, and set the scope. The LCA must develop in the future although it has a number of problems. 10 refs., 5 figs., 2 tabs.

  14. Earth-friendly refuse processing. Chikyu kankyo wo kangaeta gomi shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishigaki, M. (Takuma Co. Ltd., Osaka (Japan))

    1994-06-15

    This paper contains six articles: (1) Earth-friendly Garbage Disposal, (2) Erasable Copy Machine, (3) Making Plastics from Shell of Crustacean, (4) From Garbage into Petroleum, (5) Utilization of Sewage Sludge for a Recycle-type Society, and (6) FRP Boat Disposal Technology. All articles address the latest topics about disposal of wastes and garbage that have been attracting general attention in environmental issues. The article (1) presents the latest waste incineration technology, garbage power generation, and disposal and utilization of incineration residues. The article (2) is about a prototype of the copy paper regeneration device (toner remover) developed and produced by Ricoh Co., Ltd. The article (3) describes biodegradable plastics using chitin and chitosan that can be acquired from shell of crustacean. The article (4) describes how to extract oil or gas from plastic waste through its thermal decomposition. The article (5) presents volume reduction and utilization of sewage sludge. The article (6) presents disassembling and disposing waste plastic boats that have been rapidly increasing. 8 refs., 27 figs.

  15. Energy, environment and pursuit of happiness; Energy kankyo mondai ningen no kofuku kara kangaeru

    Energy Technology Data Exchange (ETDEWEB)

    Shingu, H. [Kyoto University, Kyoto (Japan)

    1997-05-05

    The energy and environment issue was considered from a viewpoint of human happiness. The paper picks up economy, philosophy, energy and humans as organisms, and considered how the principle of the increase by geometrical progression plays an important role in these. That the repetition in phenomena is like the increase by geometrical progression means that changes increase not linearly but exponentially and nonlinearly and bring such large changes as are unimaginable. The increase in entropy, which is caused by a nonlinear increase of the state, is an irreparable change. The problem of the pursuit of happiness also cannot be solved by the linear thought. The energy and environment problem cannot reach the solution in an extension of the linear thought in which humans have overcome poverty and lacks since the past and pursued richness earnestly. Namely, it is necessary for the 21st century to stop thinking of the energy utilization for seeking for much more richness and to try to think the energy issue in the social system where happiness with not too much richness is presupposed. 16 refs., 1 fig., 1 tab.

  16. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  17. Research result information for agriculture and environment. No.12; Nogyo kankyo kenkyu seika joho. 12

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-26

    Essential purposes of productivity improvement, which human being have desires in agriculture for a long time, can not be discussed without considering relations with the environment, nowadays. In these situations, significant investigations have been created among the researches in the agriculture and environment field in response to the requirements of the time. In this report, results of 41 main researches submitted to the agriculture and environment research promotion conference in FY 1995 are compiled. This field covers the environment and resource characterization, the agrioecology, and the environment assessment and control. The environment and resource characterization field includes studies on the micro-meteorological mechanism of desert expansion due to excess pasturage, the salt removal function of clays, and the protection of ground water quality by grassland. The agrioecology field includes studies on the antimicrobial substance contained in Glycyrrhiza glabra against the soil decease of potatoes caused by Streptomyces scabies and the new plant growth obstruction substance contained in Sphenoclea zeylanica. The environment assessment and control field includes studies on the producing district change prediction of main grains accompanied with global environmental change and the carbon balance in the ecosystem of farm lands and rice fields. This report includes a lot of noticeable papers. 103 figs., 24 tabs.

  18. Development and environment of new electric automobile, `Ecovehicle`; Shingata denki jidosha eko vehicle kaihatsu to kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, H [National Inst. for Environmental Studies, Tsukuba (Japan)

    1996-10-27

    This paper introduces history of the development of an electric automobile, `Ecovehicle`. It is provided with a high overall energy efficiency compared with an engine vehicle. The Ecovihicle is 1.2m in width, 3.3m in length, 2 seating capacities and 910kg in overall weight with serially connected 56 batteries of each 4V, 40Ah and having the total weight of 269kg. Its travel distance per charging is 130km at a speed of 80 k.p.h. This vehicle is capable of running with an energy of approximately one third as much as that of a light car. In addition, the vehicle is provided with polycrystal solar batteries placed on 0.6m{sup 2} area on the roof and spoiler generating 60W maximum. Assuming the annual duration of sunshine is 1,800 hours, charging is possible for 63kWh annually. Assuming the charging efficiency is 83%, charging is possible about seven times, which is an equivalent of travelling about 1,000km annually. The characteristics for example are the employment of brushless DC motor, use of energy saving switching element IGBT in order to realize a low level of loss in the inverter, in-wheel motor system, and storage of storage batteries in a hollow aluminum frame installed under the floor. 2 refs., 5 figs., 1 tab.

  19. Fibredrain method. Environmentally friendly vertical drain; Fiberdrain koho. Kankyo ni yasashii vertical drain koho

    Energy Technology Data Exchange (ETDEWEB)

    Suto, Y.; Inoue, T. [Fukken Co. Ltd., Hiroshima (Japan); Miura, N. [Saga University, Saga (Japan). Faculty of Science and Engineering; Yoshida, Y.; Hamada, K. [Hiroshima Prefectural Government Office, Hiroshima (Japan); Aboshi, H. [Hiroshima University, Hiroshima (Japan)

    1997-11-01

    Ground improvement using fibredrain (FD) material has not been used in Japan. For its practical use in Japan, laboratory experiment was made on such technological characteristics of FD material as tensile strength and permeability, and field test was also made to verify its improvement effect. A plane FD specimen of nearly 90mm wide and 9mm thick is composed of a folded double jute fabrics band and 4 twisted coir ropes arranged between the jute fabrics at even intervals, and the band is sewn up along center lines between the ropes. A mean permeability coefficient is estimated to be {kappa} = 1.0times10{sup -1}cm/s and {kappa} = 1.0times10{sup -2}cm/s at {sigma}{sup 3} = 0.5kgf/cm{sup 2} and {sigma}{sup 3} = 2.0kgf/cm{sup 2} in lateral pressure, respectively, showing sufficient permeabilities for vertical drain material. The tensile strength of fresh FD material is estimated to be a little stronger than 900kg/material width which is far stronger than that of conventional FD materials. The field test result showed that the FD material achieved the target for ground improvement, and has sufficient functions as a substitute for SD material. 6 refs., 10 figs.

  20. Investigations on an environmental technology transfer information network; Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With developing countries (APEC countries) as the main objects, investigations were carried out to issue environmental technology transfer information that Japan has accumulated, and advance exchanges of technical information with persons related inside and outside Japan. As a result of the investigations, it was found that the environmental technology information that serves more effectively for the developing countries is the technical information that has been developed by repeating improvements, has provided actual results in work sites, and is actually used, rather than the state-of-art technologies. Based on this result, business entities having factories and operation centers located in Mie Prefecture and the city of Yokkaichi were asked to provide data for the actually used environmental technologies. Out of 51 items provided by 17 companies, nine items were selected to be used as prototype database materials for an information network. The objects of information sources will be expanded to a nationwide scale in the future to improve the contents of the database. Problems of handling information copyrights and technical know-hows were presented in the course of data collection, urging the necessity of due considerations on the matter. Necessity was indicated on maintenance and management of data base as well as its quantitative expansion. 1 ref., 4 figs.

  1. International Symposium for the Promotion of APEC Environmental Technology Exchange; APEC kankyo gijutsu koryu sokushin symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-11

    The International Symposium for the Promotion of APEC Environmental Technology Exchange was held under the theme `The function and role expected of the APEC Virtual Center,` with the objectives of clarifying the need for future intra-regional environmental technological exchange, defining the types of information and personnel exchange, and promoting the use of interactive character of the APEC Virtual Center for Environmental Technology Exchange by encouraging access to and participation in the Virtual Center project. It was held in the period of 11th and 12th, November in 1996, at the venue of Rinku International Convention Center in Osaka. The symposium was attended by 477 persons from nine countries, i.e., Australia, Canada, China, Indonesia, Korea, Philippines, Thailand, the US, and Japan, comprising staff members of intra-regional environment-related organizations. After the keynote speech, `Current status and tasks of environmental technology exchange`, and `Expected roles of the Virtual Center for Environmental Technology Exchange` were discussed. During the plenary session, the chairman summarized the symposium. This summary was carried on the Virtual Center homepage of the Internet

  2. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  3. 24-hour society and working environment; 24 jikan shakai to rodo kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, Jun' ichi [Kansai Electric Power Corp., Osaka (Japan)

    1999-07-25

    Naturally, a human being has a rhythm with a period of about one day for hormone distribution and body temperature. This rhythm is called circadian rhythm. An ecological watch controlling this rhythm exists in supraoptic nucleus of brain, and its inherent period is clarified to be about 25 hours. Light, temperature, sound, smell and the like are the elements to improve arousal degree of brain and adjust the interior watch. However, a strong light does not only have the direct effect on improving immediately arousal degree and performance but can also shift the interior watch. Specifically, the interior watch becomes slower when a human body is bathed in an intensive light in midnight, whereas it becomes faster when bathed in an intensive light at daybreak. Consequently, this phenomenon can be used to shift the sleepy peak of a person on night duty from the working time to daytime sleeping time zone. The technology using light to improve arousal degree is utilized in space shuttles, atomic power plants, petroleum refineries and the like in USA. (NEDO)

  4. Emergency housing after natural disaster; Shizen saigaigo no oukyu kyoju kankyo seibi sisutemu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Masami [Kyoto University, Kyoto (Japan). Graduate School of Engineering

    1998-12-16

    In Japan, there were some serious disasters in recent years. In 1991, Unzen-Fugendake erupted and more than 1,000 people were forced to take refuge from their houses. In 1993, Hokkaido-Nanseioki earthquake attacked the south-east area of Hokkaido and more than 3,557 houses were destroyed. In Japan, the government supplies the temporary housing to those who lost house from the natural disasters. The purpose of supplying temporary houses mentioned in the disaster relief law (established in 1947) prescribes the purpose of temporary housing that to rescue the poor who can not afford getting a shelter with their own funds. But actual condition of temporary housing is completely different. Government supplies temporary housing to all those who request temporary housing. The term of using temporary house tend to become longer. The regulation about temporary housing has not been yet up to dated. Many problems concerning about temporary housing originate in outdated regulation. The temporary housing have to be ranked in the part of restoration process from natural disaster. (author)

  5. Production environment in mineral water plants; Mineral water kojo no seisan kankyo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimatsu, A. [Morinaga Engineering Company, Tokyo (Japan)

    1996-01-05

    This paper summarizes mineral waters as commercial products, and the manufacturing facilities thereof. The most widely used pattern of packaging mineral waters is to use either PET bottle or back-in box. The manufacturing process consists generally of: rough filtration of natural water, storage, activated carbon filtration, filtration, sterilization, ultrafine filtration, warm water bottling, capping, cooling, cartoning, storage, and shipment. The rough filtration removes sands. The activated carbon filtration removes water soluble organics. The sterilization is carried out under conditions of retaining the water at 75{degree}C for 15 seconds or retaining at 120 to 140{degree}C for 2 seconds. The ultrafine filtration uses a ceramic filter with a thickness of 0.2{mu}m. Sterilizing harmful microorganisms uses heating operation and filters to remove bacteria. An example may be cited that uses a bio-clean room for the purpose of controlling the harmful microorganisms. Subject microorganisms include a variety of viruses, rickettsia, bacteria, and fungi. The super-high performance (HEPA) filter used in the sterilization is demanded of collecting dusts with sizes of 0.3{mu}m or larger at a collection efficiency of 99.97% or higher. 3 refs., 4 figs., 1 tab.

  6. Biomethylation in the natural environment: a review; Shizen kankyo ni okeru biomethylation

    Energy Technology Data Exchange (ETDEWEB)

    Tao, H. [National Institute for Resources and Environment, Tsukuba (Japan); Fatoki, O. [University of Fort Hare, (South Africa)

    1997-09-25

    This paper explains mechanism of biomethylation of such elements important in environmental science as As, Hg, Sn and Pb, and its significance in the environmental science. Biomethylation is a process to bond methyl group directly to metals by actions of living organisms, which is occurring widely in the natural environment. Addition of methyl group onto metallic elements has a high possibility of changing their chemical and physical properties and increasing their movability, thus affecting the geochemical circulation. Particularly, such elements are important for the environmental science as As, Hg, Sn, Pb, Se, Te, Ge, Sb, P, S, and Cl. Deposits in water zones which have been regarded previously as final settling places for heavy metals are active media for anaerobic bacteria which can cause methylation. Important molecules involving in methylation are S-acenosylmethionine (SAM) and methylcobalamin which is a derivative of vitamin B12. The SAM is regarded as sulfonium salt, and the methyl group is transferred as a carbocationic intermediate. 106 refs.

  7. Image diagnosis of plant function under environmental pollution. Shokubutsu de kankyo osen wo shindansuru

    Energy Technology Data Exchange (ETDEWEB)

    Omasa, K. (National Inst. for Environmental studies, Tsukuba (Japan))

    1993-12-20

    Various physiological reaction of plants would be obstructed and troubles of their growth would be met under environmental pollution. There are also cases that the polluted materials as nutritious components are absorbed by plants. Consequently, if plant's reaction on this environmental pollution would be used, indexes of environmental pollution and environment can be improved. For examples, Ipomoea Nil and Petunia having high reaction on photochemical oxidate are widely used as index plant of air pollution. Zelkova trees and poplars planted as street trees can also greatly absorbed the polluted gas and have a function to clear air. In this paper, a diagnosis method by visualizing plant's reaction on environmental pollution by using technique of image measurement was explained. As devices of usable image measurement, a thermal camera, a solid measuring cameras, an ultrasonic camera, a multi-spectral camera and an X-ray TV camera were given. 6 refs., 4 figs., 1 tab.

  8. In the environmental pollution air raid of NATO; NATO no kubaku ga kankyo osen ni

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-05

    In recent European Union commissioned report, there was no evidence that the air raid of the NATO military in Yugoslavia became a cause of the large-scale ecology destruction until now. However, the pollution is very serious in industrial area suburb which becomes a target for Novi Sad and Pacncevo, Prahovo. The Hungary-based Regional Environment Center for Central and Eastern Europe in Hungary: REC was reported. According to REC, the pollution of the Danube river after the air raid which reaches for 11 weeks by the NATO military was serious, and ammonia of 100 tons, ethylene dichloride over the 1 thousand tons, 33% hydrochloric acid solution of the 1 thousand tons escaped to the Danube river from the air raid of Pancevo on April 18th. And, the mercury accumulated in sodium hydroxide of about 3 thousand tons, liquid chlorine of several decade tons and chlorine/alkali plant also escaped from Pancevo. United Nations-led Environmental Damage Assessment Mission should inspect Kosovo and Yugoslavia on July 19th, and it was announced with 'NATO does not show still us all well-informed information'. The investigation is carried out on the item which the Yugoslavia authorities designates, and the atmosphere level of VCM has reached 10600 times the concentration of the acceptable level near Pancevo, and it reports that acid rain was observed in each place. (translated by NEDO)

  9. Environmental pollution by dioxin and its biodegradation; Dioxin ni yoru kankyo osen to sono biseibutsu bunkai

    Energy Technology Data Exchange (ETDEWEB)

    Nojiri, H.; Yamane, H.; Omori, T. [Tokyo Univ. (Japan)

    1998-10-20

    Polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and coplanar polychlorinated biphenyls (Co-PCBs) exhibit similar chemical and biological properties. Because of their highly toxic activity, the pollution with these compounds, which are called dioxin-related compounds, is one of the most serious environmental problems. In this review, we described the analytical methods of dioxin-related compounds in environmental samples, especially in the exhaust gas from the incineration site of municipal solid waste. In addition, we described the present situation of environmental pollution by dioxin-related compounds, including pollution levels in environmental, human, and food samples, daily intakes, and risk assessment. On the other hand, a number of microorganisms have been reported which are able to degrade dioxin-related compounds including PCDDs and PCDFs. These microorganisms are classified into two groups, lignin-degrading white rot fungi and the dioxin-degrading bacteria. We also described the degradation pathways of dioxin-related compounds in these microorganisms, and their degradative enzymes. 47 refs., 5 figs., 4 tabs.

  10. Application of FEM flow analysis to environmental engineering. FEM ryutai kaiseki no kankyo gijutsu eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, M; Ando, K; Shimada, S; Umetani, H [Toyota Motor Corp., Aichi (Japan)

    1990-04-25

    In order to apply FEM (finite element method) flow analysis to environmental engineering, the two-dimensional analysis system was developed, and applied to the design of plant ventilation and improvement of an enviromental control equipment. Furthermore, the three-dimensional analysis system was developed to extend its application. Since in a large scale model, no enhancement of a processing capacity was expected even by a supercomputer because of longer I/O times between internal and external memories caused by a small internal memory space, the parallel processing system with multiple external memories was introduced to analyze such models. To achieve more efficient processing, multiple series of renumbering codes were also prepared to optimize the processing order of solvers, elements and nodes. As examples, the improvement of a thermal oxidizer and the ventilation design for a forging plant, and as an example of a three-dimensional large scale model, the flow analysis around a plant were presented. 8 refs., 17 figs., 1 tab.

  11. Global environmental problems in the electric industry. Denki jigyo ni okeru chikyu kankyo mondai ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Sugi, T [Tokyo Electric Power Co., Inc. (Japan)

    1992-09-30

    Since the electric industry has grappled with a prevention of the environmental pollution such as the air pollution and water contamination as a forerunner in case of construction and operation of the power facilities, and at the same time has conducted actively the environmental conservation countermeasures, it has consequently achieved the environmental conservation level as a top level in the world. On the other hand, as for the emission quantity of CO2 relating to the earth warming, the power field occupies about one fourth of total Japan. Therefore the electric industry should aim at the electric energy supply considering the influence on the environment, such as the power supply structure to restrain CO2 emission as less as possible, higher efficiency of equipments, higher efficiency of energy utilization by using the unused energy and so forth. In addition to it, the consumer side should aim at the social structure with a recycle type such as saving resources and saving energy, and aim at changeover of life style. It is hoped to conduct the overall measure including the items mentioned above. In this report, the recent trend of earth enviromental problems, grappling with the environmental problems as a forerunner such as the prevention measure of air pollution in the thermal power plant, etc., and the correspondence to the earth warming problems are outlined. 11 refs., 9 figs., 3 tabs.

  12. Synthesis of new erodable polymers response to environmental stimuli; Atarashii kankyo chowagata bunkaisei plastic no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, M; Nagasaki, Y [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1997-02-01

    This report relates to the designing of functional materials that decompose in response to various signals. A derivative of {alpha}-bromomethylstyrene is caused to act on the living anions of {alpha}-methylstyrene for the synthesis of a pyrolytic polymer having unsaturated groups at its terminals. The terminal double combinations of this polymer split under the influence of heat, acid, or base for depolymerization which is quantative, and the decomposition temperature may be controlled by replacing terminal phenylallylic groups with methyl groups or phloro-groups. Furthermore, a novel polythyramine polymer is synthesized with its principal chain constituted of NCH2CH2Si, the principal chain easy to disintegrate when exposed to an electron beam. The polymer is signal-responsive and may be patterned by use of an electron beam. As a temperature-responsive polymer with the hydrolytic feature controlled, poly(thyroxy ethylene glycol) is obtained from a derivative of diaminosiloxane and oligo-oxyethylene. This is a high-mobility, temperature-responsive material whose hydrolysis may be controlled. 3 refs., 2 figs.

  13. Our trials of recovering wetlands for waterbirds; Mizudori to mizube kankyo zukuri

    Energy Technology Data Exchange (ETDEWEB)

    Hasuo, S. [Chiba Prefectural Government Office, Chiba (Japan)

    1994-08-10

    This paper explains the ecology of wild birds, and describes a number of attempts at the Gyotoku wildlife sanctuary to build wetland environments for waterfowls to live. Many of wild birds use shallow marshy grounds, rivers, ponds, and tidelands as their place of living. There are not only birds living on fishes, but like wild ducks those living on plant seeds, algae on mud, and small animals. Others live on shellfishes and insects. Their environmental conditions for hatching and breeding are also a large factor. Among the `estuary area sets` where these environmental conditions are available, the continuation of tidelands is now endangered. One example is the Shinobazu pond in Ueno, Tokyo. Fulica, for example as a representative bird living at swamps, requires vegetation around its living area, affluent submerged plants, an open area with a radius of at least 200 meters to be available, and water depths from about 0.5 m to 2 m. At the Gyotoku wildlife sanctuary, long-lasting observations are continued at several test ponds having different conditions and water qualities. 4 figs.

  14. Gas removal technique to maintain global environment. Chikyu kankyo hozen no tame no bojo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1992-10-12

    This paper describes the removal technique of gases such as CO2, SO2 and NOx which have the deep relation to the maintenance of global environment. This paper describes partially r SO2 and NOx which are the primary cause of acid rain. As for the removal of CO2 generated from fixed sources (thermal power stations and others), the separation technique and isolation-fixation technique have been researched on and developed. Of the separation method, the effect of the chemical absorption method and the adsorption method is proved with the preceding experiments. The isolation method is differently researched on as to store under deep sea or ground but may be urgent and temporary. The fixation of CO2 is a serious global problem which relates to the afforestation and forests. The fixation which uses coral reefs in ocean as the absorption source has a potential. As for the processing of substances causing acid rain, the desulfurization from petroleum and the flue gas desulfurization have the excellent results. The improvement of combustion method or the flue gas denitrification at the fixed sources are used to remove NOx. The removal of NOx from all diesel cars is difficult compared with the exhaust gas cleaning of gasoline cars and is not commercialized. 11 refs., 1 fig., 2 tabs.

  15. Bibliography on Cold Regions Science and Technology, Volume 53, Part 1

    Science.gov (United States)

    1999-12-01

    Malhotra, V.M., International Conference on Devel- Yuan, R.C., Thompson, D.B., Cereal chemistry, July- Showa kichi oyobi Domu Fuji kansoku kyoteni...cryogenic system. Microflora of the deep glacier horizons of Central de Ia banda C, en los estudios del medio ambi- Antarctica. ente, sector andino y...extra- andino de la Patago- Schiek, S., Bell, G., SPIE-The International Soci- Abyzov, S.S., Mitskevich, I.N., Poglazova, M.N., nia, Argentina] Vol

  16. Report on 1988 research result on the R and D of observation system for probing resources. 2/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the specialized study in the R and D of the observation system for probing resources. In the interface with the satellite body, the result of the 1986 basic design was reexamined, elucidating the interface conditions, while the telemetry command items were also rechecked, clarifying the restrictions of the operation. In addition, the combination tests of mission equipment were all put together. Reexamined also were the interface specifications of optical sensors. Concerning the interface between the satellite body and the mission transmitter, examination was made on the detailed design level. In the operation mission analysis, algorithm for acquiring mission equipment data was reviewed, as were the operation analysis program and the data acquiring simulation. With a case examined in which an optical sensor satellite image was used for probing oil, the conclusion was obtained that the present design specifications were sufficient. In the experiment of the on-aircraft multi-channel image sensor, the subject sensor was found much higher than before in the performance for identifying rocks/minerals and was expected to be useful for resource probes. Image analysis of the test site was also performed. (NEDO)

  17. Estimation of shallow ground structure using short-period microtremors array observation. Results in Morioka area; Tanshuki bido no array kansoku ni yoru senbu chika kozo no suitei. Moriokashiiki ni okeru kekka

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Obuchi, T; Saito, T; Iwamoto, K [Iwate University, Iwate (Japan). Faculty of Engineering; Yoshida, Y [OYO Corp., Tokyo (Japan)

    1996-05-01

    The velocity structure in the shallow ground structure was evaluated by observing microtremors of 1-10Hz in the Morioka City area. Plural wave sections free of vehicle noises or the like were selected out of the collected microtremor records, and the Fourier spectrum and coherence were calculated. Records sufficiently supporting the correlation between seismographs were chosen for the analysis. The phase velocity was calculated for each observation spot from plural array records by use of the F-K spectrum. The underground velocity structure was estimated by the inversion process using the matrix method. In this method, an early model was built on the basis of the observed phase velocity and the optimum underground velocity structure was determined by alternately performing two inversion processes: one for the case wherein the S-wave velocity is the sole parameter and the other for the case wherein the layer thickness is the sole parameter. As the result, a shallow underground velocity structure, which has good agreement with the available boring data in the Morioka City area, was successfully estimated, verifying the validity of this method. 4 refs., 7 figs.

  18. Report on 1985 research result on the R and D of observation system for probing resources. 2/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This paper explains the result of R and D of the observation system for probing resources in fiscal 1985. Concerning the interface with the satellite body in the system design and control, the design was clarified for the exclusive use of the interface between an on-satellite synthetic-aperture radar and the satellite body, as were the conditions/specifications of the optical part, detector and signal processor of the sensor system, with the studies conducted for the purpose of switching over to the basic design of the following year without difficulty. Then, an examination was carried out for the basic design level of the interface between the satellite body and the transmitter of the mission. A detailed examination was made for the purpose of smoothing the interface between the mission transmitter of the earth resources satellite ERS-1 and the terrestrial station. In the operation mission analysis, an investigation was made into the efficient operation of on-satellite equipment, with studies made on the conditions and specifications of an on-satellite optical sensor. In the studies of the system design evaluation technology, picture quality of the optical sensor was examined, as were sensor specifications suitable for the probe of oil and other underground resources. In addition, aircraft/space shuttle experiment plans were also examined. (NEDO)

  19. Estimation of Rayleigh-wave spectral ratio from microtremors using a three-component single-station seismograph; Itten sanseibun bido kansoku ni motozuita Rayleigh ha shinpukuhi no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Mizutani, K; Saito, t [Iwate University, Iwate (Japan). Faculty of Engineering

    1997-10-22

    Discussions were given on the possibility of estimating Rayleigh-wave spectral ratio utilizing phase difference between horizontal movements and vertical movements by using a three-component single-station seismograph. The test has selected as an observation point a location in the city of Kushiro where a pulp and paper mill generating microtremors is the focal point, and the underground structure at that point has been estimated by using the vertical array observation method. The observation system has used three components of a velocity type seismograph having a natural period of one second, an amplifier and an analog data recorder. As a result of the discussions, the following matters were made clear: the spectral ratio with a phase difference of 90 degrees agrees with the frequency at a peak trough of the theoretical Rayleigh-wave spectral ratio; the values of the spectral ratio at the phase difference of 90 degrees and the values of the theoretical Rayleigh-wave spectral ratio correspond well excepting in frequency bands of the peak trough; and these results suggest that the Rayleigh-wave spectral ratio may be estimated by utilizing the phase difference between horizontal movements and vertical movements. Estimation of the underground structure by using the inverse analysis of this Rayleigh-wave spectral ratio is expected in the future. 6 refs., 5 figs., tab.

  20. Experiment for estimating phase velocity and power fraction of Love wave from three component microtremor array observation in Morioka area; Moriokashiiki deno bido no sanseibun array kansoku ni yoru love ha no iso sokudo oyobi power hi suitei no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, H; Yakuwa, A; Saito, T [Iwate University, Iwate (Japan). Faculty of Engineering

    1997-10-22

    Three component microtremor array observations were carried out in two locations in the city of Morioka for an attempt of estimating phase velocity and power fraction of Love wave by applying the expanded three component spatial self-correlation method. The microtremors were observed by using a seismograph with a natural period of one second. The arrays were so arranged as to form an equilateral triangle consisted of seven points. The maximum radii were 100 m, 50 m, 25 m and 12.5 m for vertical movements, and 100 m and 30 m for horizontal movements at the Iwate University, and 80 m, 40 m, 20 m and 10 m for vertical movements and 90 m for horizontal movements at the Morioka Technical Highschool. The analysis has used three sections, each with relatively steady state of about 40 seconds as selected from records of observations for about 30 minutes. The result of the discussions revealed that it is possible to derive phase velocity of not only Rayleigh waves but also Love waves by applying the expanded spatial self-correlation method to the observation record. Thus, estimation of underground structures with higher accuracy has become possible by using simultaneously the Rayleigh waves and Love waves. 3 refs., 11 figs., 2 tabs.

  1. Report on 1988 research result on the R and D of observation system for probing resources. 3/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the specialized study in the R and D of the observation system for probing resources. In the system development of the synthetic-aperture radar (SAR) to be loaded on the earth resources satellite ERS-1, the basic design was reexamined, with an SAR system test carried out. A combination test was performed for SAR and the mission transmitter. The testing device was also improved and manufactured. The optical sensor needs to be a system that uses a wide wavelength area and that is capable of receiving a image data of a high surface resolution; accordingly, on the basis of 1988 results, it was tested by preparing an engineering model (EM). The mission recording device records the observation data of SAR and the optical sensor in an invisible area, reproduces it in a visible area in the ground station, and obtains data. The EM development test implemented in fiscal 1987 was continued for the electronics part and the transport part, with the specifications and interface control documents established simultaneously. Combination tests with the mission transmitter were carried out. Studies were also stated on the antenna part/transmitter part of the mission transmitter. (NEDO)

  2. Report on 1984 research result on the R and D of observation system for probing resources. 1/2; 1984 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The 'space development policy outline' of Japan was reexamined in February, 1984, which decided on promoting the earth resources satellite (ERS-1) project. Accordingly, the Government Research Institute decided to implement the 'observation system for probing resources' from fiscal 1984. On January 18, 1985, a technological association for resource remote-sensing system was established and entrusted with the 'R and D of observation system for probing resources' from the Institute. This paper is the summary of the research results submitted as the 'report on the results of 1984 assigned research'. The report outlines, first as the 'introduction', the purpose of the establishment of the research association, details of the establishment, organization of the association, development system, development schedule, etc., and summarized, second as the 'general remarks', the explanation of the results of the 1984 assigned research. This explanation included the objectives of the research, the state of the implementation of the research, and the results of the research, for example. The paper contained, thirdly as the 'itemized explanation', the details of the individual explanation of the result for each assigned research subject. (NEDO)

  3. Report on 1987 research result on the R and D of observation system for probing resources. 1/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper explains the 1987 results of the R and D of the observation system for probing resources. The system is scheduled to be loaded on the earth resources satellite ERS-1 for which launching in 1991 has been set. On the basis of the results until fiscal 1986, technical examination was made continuously. As to the interface with the satellite body, adjustments were made in technical items with the satellite body concerning electrical, mechanical, thermal and environmental interfaces, for example. In the sensor system, the development specifications and interface specifications were reexamined and revised. In addition, an EM (engineering model) was manufactured for each sub-system of the antenna, transmitter/receiver, and a signal processor comprising the on-satellite synthetic-aperture radar (SAR), with the development test carried out. Each specification was reexamined and revised. On the basis of the basic design of an optical sensor, an EM was manufactured, developed and tested. The related specifications were reexamined and revised. An EM was manufactured for the mission recording device and mission transmitter on the results of the basic design, with the development and the test performed. (NEDO)

  4. FY 1986 annual report on the research and development of observation systems for resources exploitation. 3/4; 1986 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    Described herein are the FY 1986 results of the research of satellite-borne synthetic aperture radar, as part of the research and development of observation systems for resources exploitation. For the radar antenna, the engineering model is designed and fabricated, and test system is studied, for confirming the electrical functions, and mechanical and electrical interfaces. For the transmitter/receiver, the basic designs of the subsystems and components are drawn, and the models are designed and fabricated for testing serviceability of the high-output amplifiers and long-term stability of the high-stability crystal transmitter/receiver. Their models are also designed and fabricated for confirming their electrical functions, and their electrical, mechanical and thermal interfaces with other systems. For the signal processing section, the interfaces with the intra-SAR, satellite body and mission transmitter are adjusted, and the results are reflected in the related specifications and notes of confirmation. (NEDO)

  5. Estimation of subsurface structures in a Minami Noshiro 3D seismic survey region by seismic-array observations of microtremors; Minami Noshiro sanjigen jishin tansa kuikinai no hyoso kozo ni tsuite. Bido no array kansoku ni yoru suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ling, S; Ishikawa, K [Hokkaido University, Sapporo (Japan); Tsuburaya, Y; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    Japan National Oil Corporation Technology Research Center has carried out experiments on the three-dimensional seismic survey method which is regarded as an effective means for petroleum exploration. The experiments were conducted at the Minami Noshiro area in Akita Prefecture. Seismometer arrays were developed in radii of 30 to 300 m at seven points in the three-dimensional seismic exploration region to observe microtremors. The purpose is to estimate S-wave velocities from the ground surface to the foundation by using surface waves included in microtremors. Estimation of the surface bed structure is also included in the purpose since this is indispensable in seismic exploration using the reflection method. This paper reports results of the microtremor observations and the estimation on S-wave velocities (microtremor exploration). One or two kinds of arrays with different sizes composed of seven observation points per area were developed to observe microtremors independently. The important point in the result obtained in the present experiments is that a low velocity bed suggesting existence of faults was estimated. It will be necessary to repeat experiments and observations in the future to verify whether this microtremor exploration method has that much of exploration capability. For the time being, however, interest is addressed to considerations on comparison with the result of 3D experiments using the reflection method. 4 refs., 7 figs.

  6. Estimation of underground structures in the Osaka-Kobe area by array-network observations of microtremors; Bido no array kansoku ni yoru Osaka-Hyogo chiiki no chika kozo no suitei

    Energy Technology Data Exchange (ETDEWEB)

    Okada, H; Ishikawa, K; Ling, S [Hokkaido University, Sapporo (Japan); Sasabe, K [Ministry of Construction, Tokyo (Japan)

    1997-05-27

    Microtremor observations have been carried out with an objective to estimate underground structures including the foundation depth in the Osaka-Kobe area which has been greatly damaged by the Hyogoken-nanbu earthquake in 1995. Different organizations have made seismic surveys and boring investigations in this area, by which elucidation has been made on the underground structures. The present observations are intended to identify S-wave velocity distribution in a wide area from the ground surface to the foundation, which is difficult to be verified by using conventional surveys and investigations. Methods to detect surface waves which are contained in microtremors include the frequency-wave number method (the F-K method) and the spatial autocorrelation method (the SPAC method). The SPAC method can estimate phase velocities of longer waves for the size of an array than with the F-K method, and is more advantageous in estimating ground structures at greater depths. S-wave velocity structure was estimated down to the foundation rocks existing in depths of about 0.5 to 2.0 km. For estimating the phase velocities in Raleigh waves, the SPAC method and the expanded spatial autocorrelation method were used. The underground structures thus derived showed a good agreement with the results of explorations using other methods. 8 figs., 1 tab.

  7. Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Seo, K; Yamanaka, H [Tokyo Institute of Technology, Tokyo (Japan)

    1997-05-27

    The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

  8. Achievement report for fiscal 1981 on Sunshine Program research and development. Development of photovoltaic power plants (Meteorological observation); 1981 nendo taiyonetsu hatsuden plant no kaihatsu seika hokokusho. Kisho kansoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-31

    The effort aims to measure environmental factors for the evaluation of plant performance and equipment durability in a test operation of a Nio Solar Heat Test Plant (built on a site formed by reclaiming a salt field at Nio Town, Kagawa Prefecture). Meteorologically observed are the amount of direct solar radiation, amount of solar radiation from unobstructed sky, time of solar radiation, wind direction, wind speed, air temperature, wet-bulb temperature, amount of precipitation, and time of precipitation. Dust fall, sea salt grain, and sulfur oxides are also measured monthly. As for the direct solar radiation (DH) on the horizontal plane, it is determined by conversion of its hourly accumulation on a normal plane. The conversion method is so adjusted as to reduce errors for time belts in the morning and evening when change is great in sun elevation. The amount of sky solar radiation is calculated by subtracting DH from the amount of solar radiation from unobstructed sky. As for the time of solar radiation, it is determined by accumulating by the use of a computer the time at which pyrheliometer output is beyond a threshold of 21mW/cm{sup 2} on the pyrheliometer. A minicomputer is used to analyze and process the observed data. The annual and monthly reports and daily records are also mentioned in this achievement report. (NEDO)

  9. FY 1986 annual report on the research and development of observation systems for resources exploitation.4/4; 1996 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 4/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    Described herein are the FY 1986 results of the research of satellite-borne optical sensors, and research and development of data transmission systems, as part of the research and development of observation systems for resources exploitation. The research program for the satellite-borne optical sensors involves studies on the design specifications, in order to clarify details of the optical sensor systems and visible to near-infrared ray radiation section. The major parts are fabricated on a trial basis and evaluated, in order to review their specifications, and collect the data necessary for the engineering model designs. The items studied for the short wavelength to infrared ray radiation section include the development specifications, and conditions of the interfaces with the satellite and with the cooler/detector sections, which are to be reflected in the design specifications. The research and development program for the data transmission systems involves basic designs of the mission recorder and examinations thereof, to draw the base lines of the satellite-borne systems. The mission transmitter antenna and electronic circuit sections are investigated in detail. (NEDO)

  10. Report on 1985 research result on the R and D of observation system for probing resources. 1/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Since fiscal 1984, the technological association for resource remote-sensing system has been entrusted with the 'R and D of observation system for probing resources' from the Government Research Institute and has been carrying out the researches. In 1985, on the basis of the preliminary design implemented in 1984, a design for the exclusive use was worked out for each system, namely, total system, sensor system and data transmission system, towards the development of EM (engineering model) scheduled to start in fiscal 1986, while a trial test was performed simultaneously for the critical components. In addition, in 1985, since the main contractor of the ERS-1 satellite body was decided to be Mitsubishi Electric Co., Ltd. by the National Space Development Agency, a system was established for the purpose of adjusting the wide-ranging interface between the satellite body and the observation system, with a concrete adjusting operation started. In connection with these assigned researches, the intended objectives were mostly achieved through the cooperation by each member of the nine associations, for which the results were summarized in this paper under the contract for research assignment and submitted as the 'report on 1985 results of assigned research'. (NEDO)

  11. FY 1986 annual report on the research and development of observation systems for resources exploitation. 2/4; 1986 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-07-01

    Described herein are the FY 1986 results of the researches of the system design management and evaluation techniques, as part of the research and development of observation systems for resources exploitation. The research program for the system design management techniques involves clarification of reviewing the conditions of interfaces with, e.g., dimensions, weight and power consumption, in order to make the synthetic aperture radar compatible with the satellite body. The data transmission circuits and ground system parameters are investigated and clarified, for smooth interfaces between the satellite-borne mission transmitter and ground station. The research program for the system design evaluation techniques involves transformation of the optical sensor data into the images, and reviews of the second draft of the optical sensor design specification evaluation, on the premise of the processes in which geological experts visually extract the geological data. The validation methods, data collecting areas, observation devices, data processing systems and the like are also investigated for the aircraft/space shuttle test plans for the resources exploitation observation systems. (NEDO)

  12. FY 1985 annual report on the research and development of observation systems for resources exploitation. 4/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 4/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Described herein are the FY 1985 results of the research of satellite-borne optical sensors, and research and development of data transmission systems, as part of the research and development of observation systems for resources exploitation. The research program for the satellite-borne optical sensors involves, e.g., plans for development of the optical sensors borne in ERS-1, and studies on the parts therefor, target specifications of the optical sections, light-collection systems, spectroscopic systems, three-dimensional observation, focus adjustment, alignment adjustment, and temperature control. For the detection systems, the efforts are directed to studies on the visible to near-infrared, and short wavelength to infrared detection and calibration systems, in order to develop the detection sections satisfying the target functions and consistent interfaces with, e.g., the satellite. The research and development program for the data transmission systems involves the major functions, interfaces with the satellite, interfaces with the mission transmitters, thermal interfaces, reliability/quality programs, and development plans, for the mission recorder. (NEDO)

  13. Report on 1988 research result on the R and D of observation system for probing resources. 1/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the R and D of the observation system for probing resources. The system is scheduled to be loaded on earth resources satellite ERS-1 for which launching in 1991 has been set. On the basis of the results until fiscal 1987, 1988, technical examination was made continuously. As to the interface with the satellite body, the specifications were revised by making adjustment in technical items with the satellite body concerning electrical, mechanical, thermal and environmental interfaces, for example. In the sensor system, the technical specifications until now was reexamined and revised. In addition, an EM (engineering model) which was manufactured based on the basic design, was developed, tested and delivered to the satellite body side. In other words, in the studies of the on-satellite synthetic-aperture radar (SAR), the test device was improved and manufactured, with the EM and SAR system developed and tested. In the optical sensor, the test device was also prepared, with the EM manufactured, developed and tested. In the data transmission system, the specifications were revised by developing and testing an EM for the mission recording device. The mission transmitter was tested with EM and also in combination with other mission equipment. (NEDO)

  14. Investigation of aerodynamic stability by wind response observation during cantilever construction of the Ikara Ohashi bridge; Ikara Ohashi haridashi sekoji no kaze kansoku ni yoru taifu anteisei no kento

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, K.; Mukai, H.; Takeda, T. [Kajima Corp., Tokyo (Japan)

    1995-12-20

    In order to ensure aerodynamic stability during cantilever construction of the Ikara Ohashi Bridge, wind response observation was carried out and discussions were given on the result. The Ikara Ohashi Bridge is a 5-span continuous PC cable-stayed bridge with the central span being a concrete bridge having a length of 260 m, which is the longest in Japan. The bridge was constructed using a method that main girders are extended from the central tower to the right and left sides while the girders are stayed by bracing cables. The bridge construction site is in an area which is often subjected to typhoons and gusts like seasonal winds in winter, hence a discussion on aerodynamic stability of the bridge especially during extension work was viewed as an important matter. In addition, the construction used two small-capacity cables spaced and bundled as the bracing material, which required verification on their aerodynamic stability. In order to identify vibration characteristics of the main girders and the central tower, wind response observation has been performed as soon as the construction was begun. As a result, the vibration characteristics of the main girders and the central tower were identified, and it was verified that vibration shape and dominant frequency can be evaluated properly by an intrinsic value analysis that uses a multi-material point frame model. Furthermore, effects of different vibration absorbing measures were compared, and the effective methods were adopted as the result. 4 refs., 12 figs.

  15. Fiscal 1998 research report on the total electric power loss reduction project for Myanmer; 1998 nendo Myanmer koku denryoku soshitsu sogo teigen project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of Japanese clean development mechanism, study was made on reduction of greenhouse effect gas emission from thermal power plants by reduction of power transmission and distribution losses of power systems in Myanmer. Study was made on technical power transmission and distribution losses for the national grid transmission system, 33kV sub- transmission system of Thaketa substation in Yangong city, and 6.6kV and 400V distribution systems of Latha and Lanmadaw townships in the downtown area of Yangong. Countermeasures for power loss reduction were considered on the basis of the study result. The loss reduction project plan includes a construction cost of 5,134,000US$, loss reduction of 7,726kW, and loss reduction of 33,213,000kWh. The project feasibility and profitability were evaluated by comparison between a financial internal rate of return (FIRR) and an opportunity cost assuming that a discount rate is the opportunity cost. As a result, FIRR was 17.36% and the discount rate was 8.89% in Myanmer. (NEDO)

  16. Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

  17. New Shinkansen operation management and control systems for Tohoku-Joetsu Shinkansen; Tohoku Joetsu Shinkansen no atarashii Shinkansen sogo system `COSMOS`

    Energy Technology Data Exchange (ETDEWEB)

    Otsuki, K. [East Japan Railway Co., Tokyo (Japan); Koda, K.; Uchimura, T.; Okazaki, S.; Imagawa, T.; Kawaguchi, K. [Hitachi, Ltd., Tokyo (Japan)

    1997-02-01

    Computerized Safety, Maintenance and Operation Systems of Shinkansen (COSMOS) has been developed to properly deal with the diversification and modernization of Shinkansen business and the improvement of its system. To avoid the concentration of duties and loads on any part of the system, the system functions are distributed into eight subsystems, which respectively cover transportation planning, operation management, maintenance work management, power system control, rolling stock management, centralized information management, facilities management, and yard operation management. The COSMOS is a huge system distributed across a large area whose 500 computers and terminals located in the eight subsystems and offices related with Shinkansen are linked by a network. A concept of autonomy and distribution is introduced into the system so that the impact on the others will be kept to the minimum in case some subsystems come to a stop. The new system is excellent in maintainability, flexibility, and extendability, and its operation room is quite compact. The COSMOS has been working smoothly since the beginning of its service, contributing to the modernization of Shinkansen business, such as rapid restoration in case of timetable disturbance, reduction in station workload, improved passenger guidance service, and centralization of section control business. 5 refs., 2 figs.

  18. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Energy Technology Data Exchange (ETDEWEB)

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

    1996-10-28

    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  19. 1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

  20. ESR study on the interaction between carbon blacks and oxygen molecules; ESR ho ni yoru carbon black to sanso bunshi tono sogo sayo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Okazaki, M.; Toriyama, K.; Konishi, Y. [National Industrial Research Institute of Nagoya, Nagoya (Japan)

    2000-02-24

    Interaction between carbon blacks and oxygen molecules has been studied by means of electron spin resonance (ESR) spectroscopy. The ESR spectra of the carbon blacks appears at the g-value of free spin, which are contributed by both isolated electrons and conduction electrons. Upon introducing oxygen to the system the ESR linewidth was broadened in proportion to the partial pressure of oxygen. In case of lampblack (LB 101, Degussa) the interaction was not so strong that it took a tong time at 77K for the linewidth to reach the maxmum value. In case of gassblack (P 140 V, Degussa), on the other hand, the oxygen was easily adsorbed at 298K and the linewidth at 77K became its maximum immediately after cooling. The number of unpaired electrons decreased when the system was kept at 298 K and the decrease was prominent for the local spins. These phenomena have been explained with a simple band model for the electron. (author)

  1. FY 1993-1999 report on all the results of the development of high performance industrial furnace; Koseino kogyoro no kaihatsu sogo seika hokokusho (1993 - 1999 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Since an phenomenon was found out that NOx emission, which was thought to be increased, will be decreased by burning the high temperature preheated air jetting it at high speed (high temperature air combustion) in industrial furnace, there appeared a possibility of technical breakthrough for achieving the heightening of energy utilization efficiency and NOx reduction by exhaust heat recovery at the same time. This project aims at conducting full-scale experiments based on the basement technology including the theoretical elucidation of the combustion mechanism and high temperature air combustion by using various experimental facilities. Further, making full use of the most up-to-date analysis methods and constructing general-purpose database, the development is also aimed at of high performance industrial furnaces such as various heating furnace, heat treat furnace and melting furnace, with the assumption of prompt commercialization of the results of the development. As a result, targets were achieved such as energy saving of 30% or more, downsizing of 20% and a remarkable NOx reduction. Core technologies of this project are in-system limit heat recovery technology, high temperature air combustion technology, temperature field control technology (furnace temperature leveling technology) and high exergy heat transfer technology (furnace temperature heightening technology). (NEDO)

  2. Fiscal 1997 report on the results of the international standardization R and D. Overall survey; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper summed up the results of the survey of tackling with the international standardization by enterprises and organizations involved in the standardization in the U.S., Europe and Japan, the results of the R and D on 20 themes for the international standardization, and the development toward the international standardization. As the R and D themes, the following were selected: the development of chemical method to analyze/evaluate metallic coatings of surface treated steel coating sheets, R and D of the basic evaluation method of functional composite particles, international standards for computer/manikins, basic technology of color image management, study on optimizing design/evaluation technology using quality engineering, study of the international standardization by economic evaluation of environmental impacts, R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells, development of a test method of halogen-free flame-retardant cables and a study of the cable standards, standard measuring methods of hormone effects of chemical substances, quantification of the sensory evaluation and international standardization in the paint field, experimental study on the international standardization for immunochemical measurement of chemical substances, etc. 24 figs., 16 tabs.

  3. 1998 Annual Study Report. Standardization for compatibility between home information devices; 1998 nendo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Wide-band POF covering Gbps as a Japan-made R and D fruit will be commercialized in the near future. It is very important to make an international standard specification for the transmission by the aid of the wide-band POF, which would be basically the standard for the future home networks. The efforts in this year were directed to finding the optimum parameters for widening the band, for which the necessary characteristics related to, e.g., transmission band and bending loss were measured and evaluated, and the specifications covering a certain range were established. The wide POF system is considered to provide the first chance of the optical transmission systems going into homes on a large scale, and the service conditions and regulations for use in homes have been comprehensively studied. These efforts have begun with collection of the measured data in consideration of operating optical elements represented by LD's, their peripheral circuits and the transmitter/receiver assemblies in which they are mounted at S400 or more. Each of the light emitting and receiving sections, including their peripheral circuits, were measured and evaluated, where they were mainly operated at a short wavelength of 650 nm, which is the same as that for the DVD. (NEDO)

  4. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  5. Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

  6. Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-08-01

    This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

  7. Integrated system technologies for water and sewage works. Information system technologies for rainwater drainage. Jogesuido sogo system gijutsu. Kou joho system

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, T; Nakada, M; Kondo, S [Toshiba Corp., Tokyo (Japan)

    1994-05-01

    The present report introduces the technological trend of rainwater drainage information system mainly with radar rain gauges. The information network must be strengthened as measures against the urban flood from the rainwater drainage. A radar rain gauge-based combination is needed of synthetic and organic processing technologies covering the traveling prediction of rainfall, data communication and rainwater drainage/flooding prediction. The correction method and data communication/display technology are explained for the measurement with radar rain gauges. In both correlation function method and rainfall area pursuit method, the traveling of rainfall is predicted by utilizing the radar information for the sewerage system. For the drainage analysis, it is necessary to quantitatively estimate the rainwater drained into both main and branch sewerage lines. It is made by preparing a rainwater drainage model. The quantitative estimation of rainwater drained into the branch sewerage lines calls for a revised Road Research Laboratory guidance by the Ministry of Construction. Supplemented with knowledge by veteran operators, the displayed image of pump operation support system is simulated for its verification. 2 refs., 3 figs.

  8. Report on achievements in fiscal 1998. Development of a technology to measure biological molecular interactions; 1998 nendo seitai bunshi sogo sayo no keisoku gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It has been indicated possible in principle in recent years to measure biological molecular interactions with the molecules in the living state by combining the technologies called the co-focussing optical system and the fluorescence correlation spectroscopy (FCS). The FCS method is a method capable of analyzing concentrations, sizes, and inter-molecule interactions through detection of fluorescence fluctuation in single molecules in submicron zones. In spite of the FCS method being a very effective method to measure interactions in biological molecules, the technology has not reached a level that allows easy utilization under the present condition. The present research and development is intended to solve the technological problems in the FCS method in the co-focussing optical system, and perform as many research and development works as possible in a short time to establish a technological foundation that can be provided to bio-industrial and medical sites. Particularly, in order to make the utilization thereof possible in measuring biological molecular interactions in cells, a measuring technology using the bi-photon excited fluorescence correlation spectroscopy was established with an objective to reduce damages to cells and their internal micro organs, and minimize effects of interference signals from the own fluorescence. (NEDO)

  9. Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

  10. Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

  11. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  12. FY1995 microalgal biotechnology for recycling of pollutants; 1995 nendo tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangta sogo saishigenka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objectives are 1) development of biological processes needed for the treatment of pollutants and the conversion of resulting biomass to value added products such as energy and fine chemicals, and 2) development of techniques for monitoring of both biological and chemical hazards associated with process operation. We developed a microalgal system for simultaneous removal of CO{sub 2}/NO{sub x} from flue gas, as well as an electro-osmotic method for recovery of microalgal cells. A strategy for effective culturing of photoautotrophic cells in photobioreactors was also proposed. We utilized waste algal biomass to produce biosurfactants, and studied about structure-function relationship of lipopeptide biosurfactants. As an energy product, H{sub 2} was produced via lactic acid fermentation of algal biomass. Physiology of marine phytoplankton was also studied in relation to the future mass production of microalgal biomass. A rapid monitoring of microbial populations was possible by using fluorescent probes. An enzyme immunosorbent assay system specific to fish metallothionein was established for the assessment of aquatic environmental pollution. Human herpesvirus latent infection was effectively applied to biological assay of environmental hygiene. (NEDO)

  13. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

  14. Report on the survey in fiscal 1998. Systematic arrangement of environment technologies. 5 (Application of advanced technologies to environmental measures); 1998 nendo chosa hokokusho. Kankyo gijutsu ni kansuru taikeiteki seiri. 5 (sentan gijutsu no kankyo taisaku eno oyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Global environment handling technologies were investigated and put into order. Universities often make research and development on themes that can be handled at laboratory levels or by simulations. Development at a practical application level is few. Technological seeds may include manufacture of hydrogen by water and steam decomposition using solar energy, and new synthesizing reactions utilizing solar energy. Included may also be urban type wind power generation, superconductive energy storage systems, biomass utilization, and natural energy utilization. Furthermore, CO2 recovery and utilization by liquefaction, alkaline metal heat power generation, and pulse power technologies can also be found. Studies on applying advanced technologies to environmental measures include composite materials, membrane separation, photo-catalysts, optical elements, porous bodies, functional polymers, bio-reactors, electron beams, and aeration. Private corporations are working noticeably on prevention of fluorocarbon and dioxin emission, PCB treatment and waste water treatment technologies, catalyst application technologies, recycling technologies, and incineration ash treatment and utilization technologies. (NEDO)

  15. Survey on research environment for young researchers in the U.S.. What attractive environment is for young researchers; Beikoku ni okeru wakate kenkyusha no kenkyu kankyo ni kansuru chosa. Wakate kenkyusha ni totte miryokutekina kankyo towa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-28

    A survey was conducted on 'what attractive research environment is for young researchers' as a theme. The young researchers are referred to as those who are registered on a master's or doctor's degree courses and what is called postdoctoral scholars who received a doctor's degree. In the survey, a few common comments were seen in over interviews on the U.S. research environment. The comments were such that, needless to say, subsidies are indispensable for researches but economic aspects of treatment are not necessarily satisfactory, that the research environment is generally good, allowing freedom in research, and that results tend to be achieved by providing a subsidy for experienced knowledgeable researchers rather than directly subsidizing young researchers with a large sum, while programs with individuality such as a fellowship are desired more. It is apparent that the interests of postdoctoral scholars are economic stability; in fact, uneasiness and dissatisfaction in the status and the treatment are pointed out in a survey by the U.S. Science Academy. (NEDO)

  16. Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

  17. Report on the invitation program for developing countries concerning technology promotion project of global environmental industry in FY 1997; 1997 nendo chikyu kankyo sangyo gijutsu suishin jigyo ni kakawaru chikyu kankyo kanren gijutsu kaigai kenkyusha shohei jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In an effort to help preserve the global environment, International Center for Environmental Technology Transfer (ICETT) contributes to the solution of global environmental problems by promoting research exchanges with developing countries. As a part of this effort, ICETT hosted an environmental development researcher who visited Japan from the Institute of Environmental Research of Chulalongkorn University in Bangkok, Thailand. The invitation was extended at the request of NEDO. During the period of this investigation between September 16 and December 14, 1997, a photocatalyst was prepared and its performance was evaluated under the theme ``Application of photocatalysis to purification of atmospheric environment.`` At the same time, roadside test spots were inspected to study the practical application of optical photocatalysis. The visiting researcher also visited the National Institute for Resources and Environment to discuss with the staff of institute. This helped to deepen understandings of the state of air pollution problems confronting Japan, Europe, and North America, as well as issues related to the technologies that have been developed to solve these problems. The visiting researcher toured the RITE and examined Japan`s progress in the development of environmental control technology through joint research involving government, industry, and academia. At ICETT, the visiting researcher received training in Japan`s approaches to environmental problems in developing countries

  18. FY 1998 survey report on the feasibility study of environmental cooperation in environmental protection technology, system, etc. for spread to developing countries; 1998 nendo kankyo taisaku gijutsu seidonado no tojokoku fukyu ni kakawaru kankyo kyoryoku kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper arranged the present situation and the problems of environmental cooperation for developing countries, and studied based thereon how to cooperate in environmental protection for developing countries in the future. At the same time, it arranged the problems/subjects posed when environment-related companies in Japan try to transfer environmental technology to developing countries, for the purpose of using them as data in studying possibility of reviewing the environmental cooperation presently conducted. A view on environmental cooperation is that as security of mankind, it is necessary to help developing countries in technology/knowledge/fund. However, a trial calculation indicated that the initial investment of 11.1 trillion yen is needed only for desulfurization and water treatment in China and ASEAN countries. Such a huge amount of money cannot be paid at all even by developed countries. As the support of environmental protection measures, the one also including energy and resource is needed. Further, the support of environmental protection measures should be the one that has the exhibition effect and influential effect, promotes efforts of developing countries' own, and pushes independent environmental measures forward. From this point of view, a study was made on what the details of the environmental cooperation should be like. (NEDO)

  19. Result of comparative experiment on environmental comfort in room using hot heat environment testing unit. Onnetsu kankyo shiken unit ni yoru shitsunai kankyo no kaitekisa no hikaku jikken kekka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, T; Kawashima, K [The Hokkaido Electric Power Co. Inc., Sapporo (Japan)

    1991-11-20

    Measurements were carried out on three buildings having different heat insulation, airtightness and heat capacity for testing the hot heast enviroments (having a room size of about 4.6 m{times}3.7m{times}2.3 m) as to the temperature differences between the upper and lower parts of the room and the MRT (mean radiation temperature, representing the temperature of radiation from the wall face). These are compared according to types of heating appliance. The result is summarize as follows: The temperature difference in the upper and lower parts is affected largely by the airtightness of the building, the difference being capable of getting reduced by rasing the airtightness even in a buildings low in heat insulation. In a building with low airtightness, type of heating appliance and its installation location affect the temperature difference. The MRT is determined determined nearly completely by the heat insulation of the wall face in a room, but it tends to be affected easily by the specification and area of windows. A floor heating system increases the MRT and generates very little difference in temperatures in the upper and lower parts of the room. A comparison using a PMV (one of the indexes for enviromental comfort in a room) was also conducted. 12 figs., 7tabs.

  20. New city model with environmental symbiosis and energy conservation; Kankyo kyosei sho energy wo mezashita shintoshi koso

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    New city concept is studied from the viewpoints of city economy, environmental symbiosis, energy and resources, transportation, urban disaster prevention, information dissemination, etc. As the result, twelve cluster cities equipped with capabilities of state capital function and administrative business, commerce, interchange of people and goods, and recreational activities are dispersed and distributed to form a double ring, populated by 0.6 million and occupying 7000ha. In a simulation of the heat island phenomenon, the temperature is lowered by 0.2-0.3degC by the dispersion of city functions, and by 0.1-0.15degC by environmental symbiosis-related measures. Primary energy consumption is reduced by 17% by reduced demand for power and heat and energy saving of 15% is attained by recyclable energy utilization and enhanced-efficiency energy supply, all thanks to passive solar systems and higher-efficiency electric machines, photovoltaic power generation, heat pump-aided utilization of waste heat and environmental heat, electrothermal energy supply from the MCFC (molten carbonate fuel cell), etc. 64 refs., 56 figs., 25 tabs.

  1. Bio-remediation in actual use and environmental impairment liability insurance. Bio remediation no jissai to kankyo hoken

    Energy Technology Data Exchange (ETDEWEB)

    Ooka, K [AIU Insurance Company, Tokyo (Japan)

    1993-08-01

    This paper introduces the American International Group (AIG) which makes conceptions and risks of bio-remediation its business, as to how the Group is really working on the business. Features of the continuing remediation involving corporations managed by AIG include the following: It has economical superiority; in-situ purification of contaminated soils is possible; and it can solve contamination issues in a short time, and makes reuse of lands possible. The remediation uses a principle of promoting the contamination purifying actions of the natural world. It activates microorganisms by supplying oxygen, water, and nutrients in suitable amounts for microbial activities to decompose chemical wastes and converts them into harmless substances such as CO2. Objects of purification include petroleum-based substances, herbicides, insecticides, and solvents. Establishing optimal parameters before purification (mediator variables and population parameters) and protocols is important. The system goes through the following steps: Hydraulic and geological experts identify patterns and levels of contamination; microorganism experts find optimal parameters in laboratories; engineers design treatment systems; and site technicians operate the system. 6 refs., 3 figs.

  2. Survey on bio-chemical complex harmonized with global environment. 3; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted of bio-chemical complex harmonized with the global environment for the purpose of constructing the material production process harmonized with the environment by the process fusion between biological conversion and chemical reaction. Palm oil was taken up as renewable raw material plant resource. The process utilizing bio-chemical reaction advances at normal temperature and pressure and is high in reaction specificity and selectivity. This is a recycling, circulation and environmental harmony type production technology which brings high yield, energy conservation, resource conservation, and low environmental loads. Waste water treatment and production of useful substances from sludge were thought as elementary technology. A possibility was studied of enzyme production by culturing solid waste, and the enzyme was applied to the hydrolysis process. The paper indicated trace components in the palm oil and the extraction method and proposed the production process of new derivatives for adding value to hydrolysate. A study was also made of the overall process flow which integrated these new processes and the material balance. The comprehensive evaluation of this new process was made from the aspect of the product structure, the market, construction cost, economical efficiency, and the environment. 133 refs., 65 figs., 56 tabs.

  3. Environmental control by biotechnology and ecotechnology, construction of ecopolis. Seibutsu kogaku-seitai kogaku to kankyo joka, Ecopolis no soshutsu

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T [Shimane Univ., Shimane (Japan). Faculty of Agriculture

    1992-09-01

    The relationship between environmental control and biotechnology is discussed, and purification of moats and lakes is taken up as a concrete example of introducing biological waste water treatment technology to ecotechnology. In addition, an overall waste disposal system connecting cities and agricultural districts is investigated. After the purification of water and waste problem solution, etc. are discussed, the importance of creating ecopolis and ecotown is described. The 3 concepts of microbial ecotechnology (high densification of organism, field control, interaction between organisms) are used to explain biological treatment technology. Attempts for direct purification and ecotechnology are described quoting a few examples. If waste produced in cities and ligneous materials or charcoal obtained from forests are mixed for treatment, effective waste treatment or new resources production may be possible. It seems to be possible to create ideal ecopolis and ecotown by applying the doctrine of irrigation, drainage and reclamation engineering and the technology established by now. 35 refs., 1 fig., 2 tabs.

  4. Research of fragranced air, environmental aroma, to human and its application. Kankyo hoko no koka to sono oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, S. (Shimizu Construction Co. Ltd., Tokyo (Japan))

    1991-06-01

    The effect of lemon, jasmine and lavender aroma on people was studied through environmental aroma experiments by 270 subjects in a meeting room for two months. As a result, the high percentage of positive responses was obtained on the sense of air cleanliness and efficiency of meetings, and a statistical significance was, in particular, obtained in the case of lemon as smoking was permitted. It was suggested that aroma had physiological and phychological effect even under conditions where the subjects were not necessarily aware of aroma. The effect of the same three aromas was also studied through experiments by 13 subjects in a VDT room for one month. As a result, the number of keypunch errors decreased in every aroma although punching speeds decreased slightly, and lemon showed a significant difference among three aromas. Based on these experimental results, the aroma generator was developed, and more than 30 environmental aroma systems combined with air conditioning ducts have been installed in Japan. 20 refs., 5 figs., 6 tabs.

  5. Report on the environmental safety evaluation sub-committee in fiscal 1992; 1992 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This paper reports the activities of the environmental safety evaluation sub-committee for the coal liquefaction plant in fiscal 1992. The sub-committee, upon having received reports on the result of environmental safety evaluation tests performed in fiscals 1991 and 1992 by NEDO, deliberated and discussed carefully the contents thereof. In order to ensure labor hygiene for coal liquefaction plant workers, health influence on liquefied oil users, and social acceptability of the liquefied oil, NEDO has performed the comprehensive brown coal pilot plant operation and oil safety tests. The tests are in accordance with the labor safety and hygiene law, the chemicals examination law, and the MPD issued by OECD, and performed on each fraction produced in the pilot plant and the whole fraction mixing the former fractions, using rats, rabbits, and guinea pigs. The test items included: acute inhalation toxicity and oral repeated administration (using rats); eye stimulation, repeated coating and skin stimulation (using rabbits); photo-toxicity (using guinea pigs); mutagenicity tests (microorganisms, bacteria and chromosome anomaly); resolution tests; fish toxicity; concentration degrees; algae growth obstruction; and water flea breeding obstruction. As the result, the toxicity was found light. (NEDO)

  6. To create and built urban environment for disaster mitigation; Saigai ni tsuyoii toshi kankyo no sozo no tameni

    Energy Technology Data Exchange (ETDEWEB)

    Murozaki, Masuteru [Kobe University, Kobe (Japan)

    1999-06-10

    Learning from disaster of the Hanshin{center_dot}Awaji Earthquake, the need for building disaster preventing town is explained. Scheme of is prevalent among the townspeople. Administrations also tend to think light of hardware, and they treate approaches lightly in which safety of hardwares of town structures is secured. There are basic questions such as learning cases of reconstruction in advanced cities, understanding that problem is in hardware rather than in software, and removing biases on disaster prevention. It is necessary that persons concerning construction give them positive solutions as problems of themselves. (NEDO)

  7. Use technologies of organic materials under various environmental conditions; Kankyo joken no tayosei to yuki zairyo??????250KKGKA4

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, s. [Ajinomoto Co. Inc., Tokyo (Japan)

    1996-06-05

    This paper describes use technologies of organic materials for selecting them under various environmental conditions. FRP is superior in mechanical strength and chemical resistance, and suitable as anticorrosion structural materials. Its chemical resistance is dependent on matrix resins. Simple polyolefine system resin is superior in chemical resistance and cost, however, because of its poor mechanical strength, it is mainly used for small parts. The composite structure is used for middle tanks or piping materials where the inside surface contacting solution is lined with chemical resistant resins such as PP and PVC, while the outside surface is reinforced with FRP. Various lining materials and lining methods are used. The following materials are used for lining: liquid resin type one such as tar epoxy resin, melting powder type one such as PE, PP and fluororesin, laminated glass fiber type one using cold setting polyester and thermosetting phenol resin, compound type one of scale-like glass flake and resin, and rubber or plastic sheet material. It is important to select optimum material for lining. 1 fig., 2 tabs.

  8. Bio-technology drawing attention for solution of environmental problems. Kankyo mondai kaiketsu demo chumokusareru bio technology

    Energy Technology Data Exchange (ETDEWEB)

    Shimazaki, A [Bank of Tokyo, Tokyo (Japan)

    1991-06-01

    Explanations are given on the recent movements in the bio-technology applications. In the United States, gene therapy has been applied to patients having damaged immune system, while in Japan the first outdoor experiment is about to begin this year on gene recombined tomatoes. In the area of the marine bio-technology, researches carried out by the industrial, governmental, and academic sectors combined, led by the Ministry of International Trade and Industry have begun, which include such an attractive subject as finding out new kinds of algae living on carbon dioxide as their special favorite diet to use them to prevent the earth warming-up. On the other hand, the difficulty of bio-business is represented by the fact that venture business groups are absorbed into larger chemical companies. In Japan, the bio-business established in individual regions related to soy bean paste and Shoyu sauce industry is a distinct feature. Deregulations and review on the patent system are in progress in the United States and Germany aiming at strengthening the business competitiveness. Expectation is placed on the bio-technology that it will contribute largely in the future to solving such a critical environmental problem as experienced in the Persian Gulf war. 1 tab.

  9. Preparation for environment of residences. Residence and information facilities; Sumai no kankyo zukuri. Sumai to joho setsubi

    Energy Technology Data Exchange (ETDEWEB)

    Nanjo, K. [Mitsubishi Electric Corp., Tokyo (Japan)

    1994-09-05

    Taking up the home automation (HA) as the information facility of residence, business and technical trend of HA system together with its present and future condition are described. The service functions of HA system used for multiple dwelling houses are home telephone function, security function, control function and visual communication function. Besides, development concept of dormitory control system and service functions which are attractive to people like owner, manager and residents are described. As for its trend in foreign countries, though in France HA system under government guidance was applied in the 1980`s, it was not successful and market related to HA system was held in check. Since 1990`s, due to government policy for its introduction, this system is getting popular in the residences of disabled person, advanced age person and so forth. As for the development of HA system, more improvement not only indoor the home but also comfort, safety and so forth linking to the outdoor system is necessary. 6 figs.

  10. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  11. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  12. Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

  13. Report on the environmental safety evaluation sub-committee meetings in fiscal 1987; 1987 nendo kankyo anzensei hyoka bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The environmental safety evaluation sub-committee has held two meeting in the current fiscal year as described below. The first sub-committee meeting (August 25, 1987) was held for the agenda of the summary of future test plans, the result of overseas surveys in fiscal 1986, the results of tests in fiscal 1986, and the summary of the test plan for fiscal 1987. The major agendum of the second sub-committee meeting (February 23) was the interim reports on the overseas survey results and the safety tests in fiscal 1987. NEDO intends to ensure the labor hygiene for workers in coal liquefying plants, the effect of liquefied oil on users' health, and social acceptability of liquefied oil. Therefore, a safety test for liquefied oil in the primary hydrogenation process was performed provisionally on brown coal PP in the initial stage of operation, in addition to bituminous coal liquefied oil at the existing 1-t/d PDU. The main contents of the test performed by NEDO are based on the labor safety and hygiene law and the law related to regulation on the deliberation and manufacture of chemical materials. Different tests using guinea pigs were carried out on the total fraction mixed at the 1-t/d PDU, and each fraction of light and heavy oils, where the liquefied oil was verified to have minor degree of toxicity. (NEDO)

  14. Fiscal 1995 geothermal development promotion survey. Natural environment survey report; 1995 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In Candidate C area for the geothermal development survey, the natural environment was surveyed and `the secondary landscape assessment` was summed up in which places proposed for drilling of large-size wells and for construction of power generation facilities are extracted and a simulation of the landscape is conducted. The area for survey is the Shiramizu-gawa region in the south of Lake Akan, Akan-cho, Akan-gun, Hokkaido. The field survey was carried out about three items of landscape, plants and animals during the June-November period, 1995. As to the flora, diverse florae including vegetation unique to alpine areas, wetlands, and fumarole surrounding areas were found in the region, which is covered with summer-green broad-leaved forests or mixed forests of coniferous and broad-leaved trees. As to the fauna, faunae inhabitant of the highly natural forests were found including black woodpeckers and mountain hawk eagles. As a result of studying the places proposed for geothermal development from the above-mentioned survey, two places were picked up in the west of the survey area, where geothermal development is comparatively less influential in the natural environment and landscape and there is a high locational adaptability. 19 refs., 56 figs., 49 tabs.

  15. Networking of research information on global environment protection technologies; Chikyu kankyo taisaku gijutsu no kenkyu joho network jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Networking is being executed with an objective of exchanging information on global environment technologies at an international level. In order to further promote the information exchange, and to make web sites user-friendly, fiscal 1998 has performed structuring a thesis renewal system. As a result of structuring the thesis renewal system, researchers can use the system as using a word processor by inputting data from a terminal in their laboratories. The data can also be made into a data base nearly semi-automatically. In addition to reducing time loss, delay and input errors because of re-entry, the researchers can make the data into a database on nearly a real time basis, and can provide their own theses to any part of the world through Internet. With regard to retaining Internet security, the security software having been introduced last year was renewed. In addition, detailed status such as daily access has become possible of identification as a result of introducing the net intellect. (NEDO)

  16. Resources, environment and solid waste management; Shigen {center{underscore}dot} kankyo mondai to haikibutsu shori no tenkai

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Nobuo [Kyoto University, Kyoto (Japan). Department of Environmental Engineering

    1999-09-20

    Solid waste management should be considered in close relation to conservation of energy and resources. The history and situation of solid waste management in Japan is outlined and the new concept of waste management is discussed for sustainable development. (author)

  17. Workshop on APEC virtual center for environmental technology exchange; APEC kankyo gijutsu koryu virtual center workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    At the 'policy maker workshop of the virtual center of APEC technology exchange' held in November 1997 in Osaka, Japan, it was agreed to organize study groups to discuss the scope of information provided by the virtual center, and to make common the classification systems and retrieval functions. In addition, the necessity was confirmed on international cooperation to promote establishment of virtual centers in different countries and territories. On the first day, Professor Ueda at the Kyoto University gave the basic lecture entitled 'global environment preservation and environmental technology transfer: problems and prospects'. Mr. Dan, the workshop manager gave the basic proposal entitled 'the future directionality of environmental technology exchange inside the APEC territories by using Internet'. Based on the basic proposal made on the first day, reports and discussions were given in the following sessions, where confirmation was made on the future directions. S1: establishment of the virtual centers in other countries and territories; S2: assurance of interchangeability of classification systems and retrieval functions in providing information, and S3: presentation of examples of inter-territorial exchange and the future directionality. (NEDO)

  18. Role of civil technology towards environmental conservation and creation; Kankyo hozen/sozo eno doboku gijutsu no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Kato, T. [Maeda Corp., Tokyo (Japan)

    1995-01-15

    The recent circumstances domestic and abroads around `environment` are showing a kaleidoscopic movement with the Earth Summit in 1993 as a turning point, such as the materialization of the Environmental Fundamental Law, enactment of environmental policy fundamental principle by the Ministry of Construction, and furthermore and adoption of the earth environmental action plan-agenda 21-by the Japan Society of Civil Engineers. Under the circumstances like this the civil work execution study committee has planned this panel discussion for study, for a purpose of catching hold of the environmental problem from a standpoint of the actual constructor and furthermore searching for what should be done. As a consequence, the various opinions have been presented as follows: Namely, in order to grapple with the environmental problems it is required for that a co-operation work of the civil engineers should be done with the people in the other field. As for the environmental problems, a discussion forecasted for the future is necessary. Because an environment itself is fuzzy matter, it would be better not to give the too clear solution for a concept. An attitude to make much of the matter which can not be counted is needed. The mitigation (influence alleviation countermeasure) is required for applying flexibly.

  19. Realization of an accelerator for environmental refreshment in case of soil; Fukyugata kasokuki ni yoru kankyo sosei eno koka

    Energy Technology Data Exchange (ETDEWEB)

    Isogai, H [Electrotechnical Laboratory, Tsukuba (Japan)

    1997-11-25

    Learning from a history of the earth of ancient times, the paper studies effects of refreshing environment and soil or making them natural and harmless mostly using primitive bacteria, and develops element technology which is industrially accelerating. The spread type accelerator working only by solar energy was installed and operated for experiment. As indices of refreshment effects, a study was comparatively made between a sugar degree of sweet potato and a yield shown in the number of potatotimesunit weight. An EM propagation garbage layer is formed, and the two sections were installed of a site of the actual installation of the spread type accelerator and a site naturally left alone. Other effects of weather, temperature and humidity which are external factors and general fertilization are offset as common modes, and a consideration was so made that only refreshment effects of primitive bacteria can be relatively compared. Acceleration effects in using accelerator for growing sweet potato could be quantitatively confirmed. As to sugar degree, because the last study was made in the beginning of summer, the underground temperature was high enough. Even only EM effects were fully effective. This time, the weather was much colder, and it was found to be a must to use accelerator. 2 figs.

  20. Environmental improvement in drying process of plastics part paint; Jushi buhin toso kanso kotei no kankyo kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, T.; Horii, H.; Kobayashi, T.; Hayashida, T. [Hino Motors, Ltd., Tokyo (Japan)

    1998-07-01

    A method is developed of applying near infrared rays to the drying of paint coatings on resin-made automobile parts, and its environment improving effects are described. Using the conventional hot-air dryer for the drying of such coatings, the portion near the top surface is hardened prior to the other portions because the heat is absorbed near the top surface. Using an infrared drying system, however, defects in the product surface attributable to the lack of uniformity in the hardening of paint or to the splashing of solvent are remedied because deeper portions are hardened first. Experiment and study are conducted for the purpose of applying a near infrared drying method to an ABS (acrylonitrile butadiene styrene) coating. It is found that the near infrared drying method takes only seven minutes to dry a paint coating for which a hot-air furnace will take 20 minutes, thus shortening the drying time a great deal. Defects of gas hole of coatings are generally dealt with by changing the setting time and drying conditions for example by increasing the amount of the diluting thinner. When an near infrared drying method is used, the amount of the diluting thinner is reduced approximately 50% from the amount required using the hot-air drying method in case of the thickness of 60{mu}m. 2 refs., 9 figs., 2 tabs.

  1. Investigations on international standardization of environmental management systems. 3; Kankyo kanri system no kokusai hyojunka ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Japan as an ISO member country identifies the state of discussions in the environmental management standard deliberation committee at ISO. Investigations were performed on international standardization of environmental management systems for the purpose of participating and cooperating in preparing and establishing international standards related to environmental management, and playing part in working, solving and improving environmental problems. Under the circumstances that environmental problems are drawing worldwide interest, the International Organization for Standardization (ISO) has been carrying out since 1993 deliberations on environmental management standards to institutionalize environmental management rules to check effects of business activities on the environment. The International Organization for Standardization/Environmental Management Technical Committee (ISO/TC207) was installed, at which series number of 1400 order was allotted for environmental management related standards, and major standards have come to a final stage of standard formulation at the TC207 Oslo conference in June 1995. In Japan, the Ministry of International Trade and Industry has established an environmental management standard deliberation committee composed of people of experience or academic standing to advance discussions on how the environmental management should be in business entities through deliberations on ISO standards.

  2. Measuring approach for effect of refreshmental acceleration into the soil environment; Kankyo sosei kasoku koka no ikkeikeisoku apurochi

    Energy Technology Data Exchange (ETDEWEB)

    Isogai, H. [Electrotechnical Laboratorys, Tsukuba (Japan)

    1998-12-05

    This paper mainly describes to a measuring method for effect of refreshmental acceleration into the soil which were employing hamlet of micro organisms for accelerating revival or refreshment of environment especially purification of sludge in bottom of polluted ponds, lakes and grounds. (author)

  3. Project to promote exchange of international information on environmental technologies; Kankyo gijutsu kokusai joho koryu sokushin jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Mutual information exchange at international levels is important for practical application of global environment preservation technologies, whereas the APEC Virtual Center was established in fiscal 1997. Fiscal 1998 has discussed the future functions of the Virtual Center, and carried out the following matters to improve the functions and achieve its stable operation. Discussions were given on common use with the centers of other countries and regions of the specifications of classification systems for information areas and provided information that are provided by the Virtual Center. Visits were made to sub-managing countries and regions for smooth operation of the study groups, and opinions were exchanged. Visits were made to coordinators and contact points established in each country and region when the Center was founded in fiscal 1997. A visit was made to the U.S. Environmental Protection Agency to exchange opinions on coordination measures with the Cleaner Production Strategy of the U.S.A. being a project similar to the subject project. In order to strengthen the Japan's Center, attempts were made to expand the linking information to wider scope. Special pages publishing concentratedly the items of information that the users are interested were prepared as part of the information provision. (NEDO)

  4. Ecological processes for Environmental Impact Assessment in Coastal Waters; Engan no kankyo eikyo hyoka (EIA) eno seitaigakuteki apurochi

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Kimitoshi. [Environmental Assessment Dept., Tokyo (Japan)

    1999-03-25

    This paper focuses on a method for estimating adverse effects on natural environment by economic development in coastal waters in Japan. In particular, the most critical relations concerning the impact on marine organisms is pointed out and discussed according to an environmental impact assessment. Relations between environmental impact assessment and marine organisms needs a quantitative ecological approach in order to succeed in sustainable development of coastal waters management. Recently, the Environment Agency of Japan pointed out the unreliability and the theme on accuracy and the staff for biology and ecology in the environmental impact study. Ecological response to environmental impact occurs in a wide spectrum of physiological and biological and biological functions. Therefore biological monitoring measures must correspond to the given time-space scale of natural mechanisms. For the evaluation of environmental impact, it is desire able to develop of experimental technics and collect biological and ecological basic data for the object. I Reconstructing the following: 1. Reconstructing a clearlistic EIA process by EIA agencies and practitioners, 2. Scorping the biological and ecological issues by EIA professionals, 3. Using the current computer technology, 4. Considering monitoring systems over scales of time and space for the ecological target and 5. Making available to public all monitoring data and reports of EIA. (author)

  5. NEDO environmental technology subcommittee. 18th project report meeting; NEDO kankyo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    In relation with the 'recent trends of global warming problems and the outline of environmental technology development office activities,' Hiroshi Mitsukawa, a NEDO (New Energy and Industrial Technology Development Organization) director, delivers a report on Japan's policy toward the international commitments of the Kyoto session of the Conference of the Parties to the United Nations Framework Convention on Climate Change and NEDO's approach in this connection to new energy technology development. Furthermore, global environment-related industry technology research and development projects are explained, which involve environmentally friendly production technology, reduction in substances that cause environmental impacts, effective use of CO2 fixation, recycling of wastes, environment restoration technology, international relationship, and so forth. In relation with the 'promotion of global warming prevention projects by the environmental technology development office,' researches for the promotion of joint implementation, climate technology initiative, international joint projects for CO2 isolation in the ocean, and IEA (International Energy Agency) agreement on the research and development of technologies related to greenhouse gas, are explained. Concerning the development of eco-cement production technology utilizing urbane type general wastes, a verification research project on the manufacture of cement from incinerated urbane waste residue and sewage sludge is reported. (NEDO)

  6. Research and development of laser radar for environmental measurements. Pt. 3; Kankyo keisokuyo laser radar no kenkyu kaihatsu. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Described herein are the results of the joint project between Japan and Indonesia to construct a new laser radar network system, which can three-dimensionally measure air pollution conditions in urban areas, in Djakarta. This joint project is implemented to elucidate the mechanisms involved in air pollution in the city, and thereby to contribute to environmental administration of Indonesia. This project is expected to give the basic approach to solution of environmental problems in urban areas, and eventually on a global scale, and hence to contribute to construction of the global network systems for environment-related information, which should be necessary in the near future. The (ODA Laser Radar Development Committee) is the deliberative body for the project, responsible for evaluating the project results. The project will be implemented on a 4-year plan from FY1993 to 1996. The activities in this year, the third year for the project, include on-the-spot survey, selection of the laser radar site, and development/improvement of the laser radar system. These results are described herein. (NEDO)

  7. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  8. Research and development of laser radar for environmental measurement. 2; Kankyo keisokuyo laser radar no kenkyu kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    This project was received by Optoelectronic Industry and Technology Development Association from NEDO, and aims to contribute to the improvement of Indonesia's environmental administration through the development of an air pollution observing laser radar (LR) and of an environmental information network system fit for use in the country in cooperation with Indonesian engineers. LRs will be installed at several sites in an urban area where environmental problems are increasingly serious, and a observation network system will be constructed to link the laser radar sites. The observed data will be collected, analyzed, and processed by an observation data processing center for the investigation of the three-dimensional spatial distribution of air pollution to determine the actual state of air pollution over an urban area. The laser radars and the network will be placed in the city of Djakarta. The Indonesian authority responsible for the project is Indonesian Institute of Sciences. In fiscal 1994, part of the equipment (difference absorbing LR) was designed and manufactured, the design of the environmental information network system was developed, and various researches required in this connection were conducted. (NEDO)

  9. FY1995 synthesis of new erodable polymers response to environmental stimuli; 1995 nendo atarashii kankyo chowagata bunkaisei plastic no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Recently, environmental pollution by a large amount of undecomposable waste has became a serious problem. Therefore, biodegradable polymers, which can be degraded by environmental species such as bacteria and enzymes, have been studied extensively. Most of the biodegradable polymers prepared so far were polyester derivatives such as poly(hydroxybutyrate/valerate), poly(lactide) and poly(glycolide). The degradation mechanism is the hydrolysis of the ester groups in the main chain of the polymer which is facilitated by enzyme degradation. Most of the mass-produced polymers, however, are vinyl-polymerized plastics such as poly(ethylene), poly(propylene) and poly(styrene). There is no technology on the degradation of such vinyl polymers except in the lithography field, in which it is known that some vinyl polymers can be used for posi-type resists by decomposition with UV or electron-beam (EB). For creation of degradable polymers, the following three factors must be considered Purpose of the project seriously; 1) What degrades the polymers? 2) Row long does the polymer maintain the initial properties? (Time course of the mechanical strength, etc.) and 3) Bioactivity of the liberated oligomers. The aim of our work is the creation of new polymers which can be easily controlled by the above three factors. If we can degrade the polymers from the end of the polymer chain, i) we can control several properties of the polymers in the degradation such as degradation source (pH, light,, UV, EB, etc.) and rate of the degradation by changing the structure of the end group; 2) production of oligomers, which may induce a significant problem in terms of bioactivity, can be suppressed because of the depolymerization from the end of the polymers (only the monomer will be liberated). In this project, we investigated to synthesize the end functionalizations of poly({alpha}-methylstyrene) derivatives and their degradation characteristics using temperature, acid and alkaline conditions. To induce degradabilities in polymers in response to environmental conditions, the end-modification reactions of poly({alpha}-methylstyrene) (PMS) derivatives were carried out. When diphenylphosphine chloride was used as a modifier for the living end of para-substituted PMS, the coupling efficiency was ca. 50%. 2-Phenylallyl halide derivatives such as 2-phenylallyl bromide, 2-(4-tolyl)allyl bromide, and {alpha}-trifluoromethylstyrene were found to be suitable end-modification agents. For example, {omega}-2-phenylallyl PMS was prepared with almost quantitative functionality by the reaction of the living PMS with 2-phenylallyl bromide. In a similar way, {omega}-3, 3-difluoro-2-phenylallyl and {omega}-2-(4-tolyl)allyl PMS derivatives were synthesized. Based on thermogravimetric analysis, onset of the degradation temperature of the end-modified PMS derivatives decreased in the following order: {omega}-hydrogen- > {omega}-3,3-difluoro-2-phenylallyl- > {omega}-2-phenylallyl- > {omega}-2-(4-tolyl)allyl-PMS. Actually, the onset temperature of {omega}-2-(4-tolyl)allyl-PMS derivatives was 50 degree C lower than that of {omega}-H-PMS derivatives. These results indicate that the active species is produced effectively at the end unsaturated bond, which initiates the depolymerization of the polymer at rather low temperatures. Ionic degradation of these polymers was also investigated using butyllithium as an anionic initiator and methanesulfonic acid as a cationic initiator Tendencies similar to the thermal degradation were observed. Therefore, it is concluded that a 2-phenylallyl substituent at the end of the PMS chain induces effective degradation through several mechanisms such as radical, anionic and cationic depolymerization reactions. (NEDO)

  10. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  11. Application of genetically engineered microorganisms to bioremediation and wastewater treatment. Idenshi sosa biseibutsu no kankyo joka mizushori eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, M; Ike, M [Osaka University, Osaka (Japan). Faculty of Engineering

    1993-11-10

    This paper summarizes the following techniques: a gene engineering method for bioremediation and wastewater treatment, microorganism breeding using the former method, and a monitoring technique for genetical and ecological stability of genetically engineered microorganisms. Recombination bacteria reinforced with PH genes showed higher phenol removing rate than wild strains, but presented accumulation of catechol in such a large quantity as cannot be seen in wild strains, with the complete degradation rate rather decreased. Gene recombined bacteria structured by introducing the recombined plasmid, pBH500, had high genetic stability when P.putida BH-1 is used as a host. E.coli C600 having recombined plasmid and P.putida BH were added and cultivated in activated sludge. As a result, both recombined bacteria showed rapid logarithmic decrease just after the addition, then, maintained the relatively stable population groups, and remained in the activated sludge for an extended period of time. In monitoring techniques, the colony hybridization process detected clearly the gene recombined bacteria. 9 refs., 7 figs., 1 tab.

  12. Trend survey of the global environment adaptation type industrial technology. Trend survey of global environment related studies (researches on measureds for reduction of environmental load of CO2); Chikyu kankyo tekiogata sangyo gijutsu doko chosa. Chikyu kankyo kanren kenkyu doko no chosa (nisanka tanso no kankyo fuka teigensaku ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The paper studies the measures for reduction of environmental load of CO2 from the standpoint of chemical technology. As for methanol synthesis from CO2, accelerating of the reaction using Cu base compound catalyst is reported. Also, CO2 is methanated at high speed by low temperature waste heat using Ni-La2O3-Ru catalyst. Discussions are given on the subject for development of catalyst reaction relating to hydrogen production technology by methane reforming reaction using steam or CO2. Synthesis of polymetric materials by use of CO2 is also described. The paper mentions that it is indispensable to design high-function electrode and elucidate the reaction mechanism of electrochemical CO2 reduction for electrochemical and photochemical CO2 reduction measures. Moreover, in case of using solar energy, it is required to study photovoltaic excitation process in semiconductor electrode/ electrolyte solution interface. For production of hydrogen from CO2 by photosynthetic organisms and solar energy, the problem is control of inhibiting effect of oxygen combinedly produced. Described are production of polyhydroxy butyric acid and biodegradable polymer from CO2 and hydrogen by bacteria, and CO2 fixation imitating the enzyme reaction. 267 refs., 79 figs., 32 tabs.

  13. FY 1999 survey report on the global environment international cooperation promotion project/global environment international information network project. Survey of the environmental technology transfer information network; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / chikyu kankyo kokusai joho network jigyo. Kankyo gijutsu inten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    At International Center for Environmental Technology Transfer, the following were conducted for enrichment of the environmental technology information: surveys of the state of activities in international organizations and developed countries, cleaner production (CP), ISO, etc. and construction of database. As to the reinforcement of environmental preservation technology information database, enrichment of the data on environmental preservation was attempted mainly about ways of thinking of environmental preservation which brought fruitful results to international organizations overseas. The hierarchization/supplementation were conducted of CP databases which attract much attention especially among developing countries. In the survey of models for environmental preservation, autonomous bodies in Mie prefecture and the certified consultant were taken up to study the process up to the acquisition of ISO14001. The database was so made that it can be a guide for the environmental management in autonomous bodies in developing countries. In the CP survey, as to the United Nations Environment Programme (UNEP), definition/thought were examined in terms of CP, eco-efficiency, pollution prevention, green productivity, etc. (NEDO)

  14. Fiscal 2000 project for promoting international cooperation for global environment. International information network project for global environment (Survey on information network for environmental technology transfer); 2000 nendo chikyu kankyo kokusai kyoryoku jigyo hokokusho. Chikyu kankyo kokusai joho network jigyo (kankyo gijutsu iten joho network chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Environmental technology information database has been shown on Internet for the purpose of transferring environmental technologies; in order to reinforce it this year, a viewpoint was directed to developing countries, with research carried out on the environmental preservation information of the Philippines and Thailand. In the research, in view of promoting cleaner production in developing countries, UNEP regional offices, which are active in the operation, and Asian Development Bank were examined, with their methods, plans and strategies of disseminating the cleaner production surveyed. Also, the database was added with the activities by the organizations concerned in Philippines and Thailand. As for the environmental management system ISO14001, some local governments in Philippines and Thailand will presumably acquire ISO14001 in the future to deal with their environmental management; under the circumstances, Miyama Town was chosen that was first in Mie Prefecture to obtain ISO14001, with the details investigated concerning its environmental policy and the acquisition of ISO14001; and, on the basis of the investigation, a database was prepared so that guidelines for environmental management were provided for the local governments. (NEDO)

  15. Photovoltaic power generation field test at Industrial Technology Research Institute. Prefectural office building in a sunshine-rich district (Kanagawa Prefectural Industrial Technology Research Institute); Sangyo gijutsu sogo kenkyusho taiyoko hatsuden field test jigyo (nissha ryoko chiku no kenchosha). Kanagawaken sangyo gijutsu sogo kenkyusho

    Energy Technology Data Exchange (ETDEWEB)

    Okazaki, H [Kanagawa Prefectural Government Office, Yokohama (Japan)

    1997-05-30

    The result of a photovoltaic power generation field test in fiscal 1996 on a prefectural office building in a sunshine-rich district is reported. It is a lighting power source installed in fiscal 1994 on the third-floor rooftop of the management information building of Kanagawa Prefectural Industrial Technology Research Institute. It has a capacity of 25kW, operating on system interconnection (no back flow), and has a single 15-series/26-parallel array (mono-crystal modules) facing 38deg westward from due south and inclined at an elevation angle of 20deg. From the 240000kWh insolation that contributed to power generation, a DC power output of 28000kWh was obtained, output of 25000kWh after conversion into AC. The module efficiency was 10.8-13.8%, higher when the daily mean temperature was lower. In the case of 3kW type expected to diffuse into the residential and commercial sector and household sector, one will output 3000kWh a year, which is an appropriate capacity as a locally distributed type power generating system in view of the monthly consumption of 2000kWh by a household in general in the Tokyo Electric Power Co., Ltd. service area. No problem is found in reliability of the tested system. Although the power it generates is less than what this office consumes, it is effective in enlightening people about resources saving and peak cut in summer

  16. Fiscal 1999 basic survey report for promotion of joint implementation. Project for overall loss reduction in Myanmar for thermoelectric power during transmission and distribution; 1999 nendo Myanmar koku karyoku sohaiden denryoku sonshitsu sogo teigen project hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With connection to the clean development mechanism (CDM) taken into consideration, a study is made about achieving greenhouse gas reduction in Myanmar through power generation facility heat efficiency improvement and power loss reduction. Taken up in the study are the Shwedaung power plant, the Mann power plant, and the power transmission system in the Mandalay District. The profitability of thermoelectric power facility improvement is calculated using the financial internal rate of return (FIRR), derivable from the cost of thermoelectric power facility improvement and the convenience to be created thereby, and using the opportunity cost in Myanmar. The result is then subjected to a feasibility study. Most effective for CO2 reduction is the addition or installation of advanced compound cycle power generation facilities which are also excellent in heat efficiency and power generation cost. The FIRR of thermoelectric power facility improvement is 9.4-12.8%, which means the effort is worth investment. Measures for decreasing power loss during transmission include the use of higher voltages, laying of new lines, employment of conductors thicker in size, and the installation of phase modifiers. The economic internal rate of return (EIRR) and FIRR are calculated for the study of feasibility. An analysis covering a 10-year period results in a 20.41% EIRR (exceeding the socially accepted discount rate of 10%) and a 17.56% FIRR (exceeding the general loan interest of 15%), which means that there is feasibility. (NEDO)

  17. Comprehensive research concerning the development of effective utilizing techniques of biological resources (large scale research out of the framework). Seibutsu shigen no koritsuteki riyo gijutsu no kaihatsu ni kansuru sogo kenkyu (ogata betsuwaku kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-25

    This paper is a research report in which the cultivated production of forest resources, the development to useful substances and the systematization to take the root in a region were studied. The distribution maps of biological resources on respective woodland systems: that is, the nationwide distribution maps of the amount of resources in Japan as to the broadleaf trees in private forests and national forests, the available amount and kinds of tree were prepared. As for the establishment of cultivation technique of the super-short deforestation forest, that is, pursue of wooden growth to the maximum limit, the superior clone 26 system was selected from the willow group through the research of wooden cultivation and the clone which showed the maximum yield reached 24t/ha every year. As for the material preparation technique due to microbial enzymes, that is, the creation and breeding of fungi which have the high lignin decomposition power, a stock of fungi which has the high lignin decomposition power and the decomposition selectivity was created by the cell fusion and the UV (ultraviolet ray) radiation treatment. As for the use of effective components in wooden resources, many useful characteristics could be detected by applying the boiling, bursting and ozone treatment. As for the mushroom cultivation through the application of unused tree kinds, a new kind of mushroom for food service was selected to clarify the possibility of fruit body formation. The development of a new material from conifers is promising. 1 tab.

  18. General evaluation survey report on fiscal 1998 investigation of geothermal development and promotion. No.C-3 Akinomiya area (Third); 1998 nendo chinetsu kaihatsu sokushin chosa sogo hyoka chosa hokokusho. No.C-3. Akinomiya chiiki (dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    With Akinomiya area (11.4 km{sup 2}) selected in Akita prefecture as the survey C area in fiscal 1996, the first survey was conducted. This paper is a summary of memorandum from an advisory standpoint on the evaluation survey concerning the fiscal 1998 investigation results. The contents of the survey are geological investigation, precision gravity exploration, soil gas investigation, electromagnetic exploration, fluid chemical investigation, well drilling and short-term eruption test. An alteration zone was recognized around the place where clay minerals used to be mined, with the center of the zone situated 500-600 m east of a fault. The alteration condition of Akinomiya area seems to be different from that of Doroyu Wasabisawa area. The supplementary gravity survey was carried out at total 58 points in fiscal 1998. It is desirable to set supplementary measuring points over a wide surrounding area for a depth structure analysis. Also performed was a study of mercury concentration in the soil gas. While CSAMT and TDEM methods were employed for the electromagnetic exploration, a suitable method should be carefully selected for a wide area high-density exploration. Consistency with adjacent areas is essential in preparing investigation items particularly for a geothermal model. (NEDO)

  19. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  20. FY 1998 report on the comprehensive analysis in the geothermal development promotion survey. Tertiary. No.C-3 Akinomiya area; 1998 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-3 Akinomiya chiiki (Dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    The geothermal development promotion survey was conducted in the Akinomiya area, Ogachi county, Akita prefecture, and the FY 1998 results were summed up. In the surface survey, geology/electromagnetism/precision gravity survey was made as supplementary survey, and re-analysis of 3D models was made. In the well survey, three wells of N10-AY-6 to N10-AY-8 were drilled to conduct the core examination, temperature/pressure logging, sampler logging, short-term jetting test, etc. Also conducted were the reservoir evaluation, environmental effect survey, etc. by pressure monitoring and water level observation. The results of the comprehensive analysis predict the following. In the Akinomiya area, there exists heat source in deep parts around Mt. Yamabushi-dake and Mt. Takamatsu-dake; Being given heat from this heat source, rocks, ground water and volcanic gas react on each other to form geothermal fluids. It is presumed that high temperature geothermal reservoirs exist in the east of the area. Moreover, the pressure distribution indicates that the Akinomiya reservoir and Wasabizawa reservoir can be a chain hydraulically. On the other hand, the west of the area is the low temperature and heat conductive area, and therefore, there seem to be no high temperature fluids there. (NEDO)

  1. International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

  2. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  3. FY 2000 Research and development of technology for medical and welfare equipment. Report on the comprehensive survey on welfare equipment; 2000 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu chosa hokokusho. Fukushi kiki sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The survey is conducted on the advanced basic and application technologies for medical and welfare equipment, e.g., biotechnology and drug delivery systems, to promote development of these technologies. For development of the gene-aided diagnostic system equipment for clinical purposes, surveys are conducted on current medical equipment and related technologies, and the results are summarized and pigeonholed for each equipment type. Also summarized are the small- to medium-sized enterprises which are considered to have techniques needed for development of sensors for heart disease treatment systems. For usability of welfare-related equipment products, investigations are made viewed from the designs oriented to human adaptability, human adaptable designs in the aging societies, and welfare-related problems in the aging societies and usability. The latest information on leading organizations and researchers is collected, for continuation and development of the usability programs for welfare-related equipment products, and also for inviting the current related technologies and researchers on life supporting for the aged in Japan to the programs. (NEDO)

  4. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  5. FY 1998 annual summary report on comprehensive development study of high-function flat panel display techniques (second year); 1998 nendo koseino flat panel display gijutsu no sogo kaihatsu kenkyu seika hokokusho. Daininendo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is aimed at creation of the new world display industry in Shikoku by developing the high-function flat panel display techniques and thereby establishing new techniques which solve the problems involved in, e.g., LEDs, plasma-aided devices and ELs other than liquid crystal devices. For development of emitters using diamond, important results have been obtained for the morphology, and cathode luminescence, Raman and photoluminescence spectra of polycrystalline diamond, synthesized by the vapor-phase process under varying conditions, on the electron radiation characteristics of the emitters. These results have led to clarification of the optimum vapor-phase synthesis conditions for diamond for high-function emitters. The techniques utilizing focused ion beams have also advanced to develop thin polycrystalline diamond films for emitters which correspond to the image elements of quality for television. For electron emitters, a structure prepared by implantation without using a high electrical field is proposed, and the device mechanisms involved are clarified. (NEDO)

  6. Overall analysis report on the fiscal 1994 geothermal development promotion survey. No.C-2. Wasabizawa area (secondary); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-2. Wasabizawa chiiki (dainiji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    The Wasabizawa area is located near the boundary between Yuzawa city south of Akita pref. and Ogachi-machi, Ogachi-gun, Akita pref, having a range of 3.0km northeast-southwest and 2.5km northwest-southeast of Wasabizawa almost as a center. The area for survey and its circumference are national forests, and the east and a part of the south of the area are designated as the Kurikoma quasi-national park third type special region. From the geochemical temperature distribution, it can be assumed that geothermal fluids of around 300{degree}C exist in the deep underground of the Kaminotai-Wasabizawa-Akinomiya area. From the distribution of density basements, the block structure of the basement can be estimated. Around the boundary of the ridge/sedimentation region of this density basement, fractures develop and the formation of reservoir structure is expected from the comparison with the result of the well survey. In the blowout test, obtained were 284.3{degree}C and 83.05 kgf/cm{sup 2} at a depth of 1,300m. In the geothermal system, it is assumed that reservoir structures of geothermal fluids develop in the deep underground of the central part of the area. The heat source to the geothermal system is supposed to be the magma reservoir remaining in Takamatsudake volcanic rocks. 110 refs., 177 figs., 105 tabs.

  7. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for securement of interconnection between intelligent home electric appliances; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Johokadenkiki kan no sogo setsuzokusei kakuho no tameno hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development had been under way since fiscal 1998 for working out propositions relating to the international standardization of connection interface systems for digital AV (audio-visual) equipment. This report outlines the result of the project in its fiscal last year. The link working group (WG) actually built a transceiver at 5 mm pitch in its second trial, measured and evaluated its behavior under high-temperature and high-humidity circumstances, and acquired numerical data for interface specifications. The connection interface WG in its second trial fabricated a tiny optical connector for POF (plastic optical fiber) and evaluated its resistance to environment. As the result, sufficient resistance to environment was detected in the connector, and then a proposition was presented to IEC/TC86 that the connector be standardized as an optical connector for intelligent home electric appliances. The POF optimization WG performed an environment resistant test for POF, similar to those for transceivers and connectors, and then recognized that POF of the GI type was low in transmission loss and that it stably retained its wide-band feature. (NEDO)

  8. Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-10-01

    With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

  9. FY 1992 Report on results of the research and development of the technologies for creating/processing advanced biomaterials. Part 2; 1992 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 2. Sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  10. Report on final evaluation of industrial science and technology research and development system. Comprehensive basic technologies for development of ocean resources. Manganese nodule exploitation system; Kaiyo shigen sogo kiban gijutsu (mangan dankai saiko system). Saishu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    Described herein are the final evaluation results of the basic research and development of the system for exploiting manganese nodules as one of ocean resources. A 9-year project was started in the FY 1981 to establish the techniques to efficiently, economically exploit Mn nodules on a commercial basis, which are occurring on deep sea bottoms (4,000 to 6,000 m deep), in order to stably supply non-ferrous metallic resources, e.g., Ni, Cu, Co and Mn, which are essential for economic activities of Japan. Originally, the UN convention related to ocean laws raised development of unique exploitation techniques as the prerequisite condition for obtaining the right to develop Mn nodules. However, the situations around development of Mn nodules were changed since then, to devalue objects, significance and urgency of this project. The fourth amendment of the basic plans decided to suspend the comprehensive ocean tests in 1996, and to implement only the ocean/land tests in which part of the individual elementary techniques were combined. Therefore, the technological validation of the overall system could not be done sufficiently, and degree of achievement of the project is low, viewed from insufficient prospects of the commercial production. However, this project produced good results in individual elementary techniques, which are of significance for the resources policies. (NEDO)

  11. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area; 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    As part of the geothermal development promotion survey, the comprehensive analysis was made on the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was conducted in FY 1999. In the evaluation of reservoirs, the following were carried out: comprehensive analysis of various data on the surface survey, well exploration, etc., which were stored in surveys from the primary to the forth, modification/construction of geothermal system models, numerical simulation using 3D models, etc. In the long-term jetting test, production/reduction tests were conducted using N9-AY-3 and N10-AY-8 as production wells and N8-AY-1 and N10-AY-6 as reduction wells. The results of the comprehensive analysis were outlined as follows. The distribution of high temperature zones promising as areas for geothermal development was grasped. The distribution of the main fracture structure underground was grasped. A total amount of 124t/h steam was confirmed by short/long term jetting tests. In the simulation of prediction of production, the result was obtained that there was potential power generation of 30MW in the Akinomiya area alone and 60MW both in the Akinomiya area and the Wasabizawa area. (NEDO)

  12. Study of dependence of DC output of rectenna array on the method of inter-connection of its array element; Rectenna array chokuryu shutsuryoku no array yoso sogo setsuzokuho izonsei no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, M.; Matsumoto, H. [Kyoto University, Kyoto (Japan). Radio Atmospheric Science Center

    1997-08-20

    In 1994 and 1995, a ground-to-ground microwave power transmission (MPT) experiment was carried out by a group of Kyoto University, Kobe University and Kansai Electric Power Company. Among the MPT technologies, which are one of the most important key issues for the realization of the Solar Power Satellite (SPS), studies of `rectenna` (rectifying antenna) have been pursued to archive higher efficiency of conversion from microwave to DC. We had developed a new rectenna panel which can effectively rectify a microwave power of 2.5 W at 2.45 GHz before the ground-to ground MPT field experiment. We examine the sum of the outputs of two or three rectenna panels in which are connected ether in parallel or in series or in the hybrid connection under the same microwave circumstances. The experiment leads us to conclude: (1) The sum of the DC outputs from two rectenna panels connected in parallel is larger than that from those connected in series. (2) The sum of the DC outputs of two rectenna panels is generally smaller than the sum of the DC output of the individual panels unless their output is equal to each other. (3) The total output DC power of a rectenna array increases when we connect the array element with consideration of the `element balance`. Based on the experiment, we propose an optimum method for connection of individual rectenna elements to form an rectenna array. 12 refs., 9 figs., 4 tabs.

  13. 1998 Annual Study Report. Standardization for securing interoperability between optical disk systems; 1998 nendo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D program is aimed at securing interoperability between optical disk systems, based on the logical formats, to propose the draft international standards. For the volume/file structures proposed by ISO/IEC 13346, the universal disk format (UDF) proposed by the Optical Storage Technology Association (OSTA) is taken as the target file system, to improve the conformance test environments and develop the standards for advanced interoperability. The 1998 R and D themes include development of the UDF conformance testing tools for avoiding the interoperability-related problems involved in the UDF, which are actually observed, and investigations on the UAF specifications and preparation of the UAF-related standard evaluation systems for preparation of the draft standards for the Universal Accessible Filesystem (UAF), planned to be conducted in and after the next fiscal year, which allows, e.g., network seamless application of a variety of the future optical disks. (NEDO)

  14. Report for fiscal 1982 on comprehensive survey for nationwide geothermal resources. Preparation of lineament density maps - radar image analyses - in north-eastern area; 1982 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Lineament mitsudozu sakusei (radar gazo kaiseki (Tohoku chiiki))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    Geological structure analysis maps and lineament maps were prepared on the north-eastern area and parts of the ancillary areas thereof by analyzing radar images of a 1 to 200,000 scale. With regard to the geological structures, analyses were performed by using as the original data the north look radar images for the three special geothermal areas to have prepared the geological structure analysis maps. The analysis of the radar images identified ground bed boundary lines in more detail than in the existing geological maps, and new discoveries were made available on faults. The lineament maps were compiled by implanting into respectively corresponding topographic maps the 24 N-S lineament maps made by the west look radar images for the whole surveyed areas, and the 16 E-W lineament maps made by the north look radar images for the special geothermal areas. Based on the clarity and characteristics deciphered on the images, the lineaments were classified into the major, minor, and subtle lineaments, which were indicated on the lineament maps. The lineaments were digitized by positions of the edge points, and the histograms and statistical tables were prepared by computer processing. (NEDO)

  15. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Appendix); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei furoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    This paper explains different theoretical calculation methods used in gravity and magnetic force data analysis in geothermal resources survey. Analyzing the gravity data and the magnetic force data is capable of being applied with the potential theory. The increased speed and capacity of recent computers make easier the conversion of data into wave number zone. In relation with heavy magnetic force analysis, the paper explains such items as basic handling, IGRF remainder calculation, methods for topographic correction, conversion of primary and secondary polar magnetism and conversion of pseudo-gravity, coherent analysis, spectral ratio method, estimation of spectra by using MEM, spectrum moment method, heavy magnetic force simultaneously analyzing type modeling, constraint inversion method, and other methods. The paper further explains the sequential approximation method in magnetization calculation, methods for calculating equivalent magnetization distribution (methods by Bhattacharyya and Chan, and Nakatsuka), method for calculating equivalent magnetization distribution (method by O'Brien), primary and secondary polar magnetism conversion relation formulas, and theoretical calculation of spectral ratio. (NEDO)

  16. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  17. Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

    1997-10-30

    The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

  18. FY 1999 Report on the technical results. Research and development project for creation of the quick-effect type international standards (Comprehensive surveys); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Safety, environment protection and internationality are most important product qualities, and international standardization of product qualities and testing methods are essential for strengthening international competitiveness. Viewed from this angle, the R and D project is conducted to propose the international standards for the following 5 areas related to environment and safety, selected in expectation that the results could be obtained in short time for preparation of the international proposals; (1) standardization of the wireless IC tags for logistics management, (2) standardization of quality and testing methods of automobile fuels and lubricants, (3) research and development for international standards in the field of safety of machinery, (4) standardization of evaluation methods for electronic data security system, and (5) standardization for the safety of light emitting diodes. The results are obtained for preparation of the international standard drafts, interim or final. The activities are directed to promotion of international interchangeability of radio frequency identification (RFID) systems for area (1); to standardization of the systems for emergency stopping/controlling machines for the area (3), to improvement of security evaluation standards of existing information systems for the area (4), and to unification of the ISO/IEC safety standards for the area (5). (NEDO)

  19. Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

  20. Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

  1. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  2. Fiscal 1999 basic survey for promotion of joint implementation. Overall study report on energy saving and CO2 reduction at Indocement Company; 1999 nendo Indo cement ni okeru shoene CO{sub 2} sakugen sogo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A study is made about the feasibility of energy saving and CO2 reduction at the Citeureup Plant of the Indocement Company, Indonesia. Future embodiment of a clean development mechanism (CDM) is also discussed. Points examined for improvement involve air quenching clinker cooler (AQC) efficiency (mixing of raw materials, use of combustion control technology, and modification into a new type AQC); the finishing process (installation of a preliminary clinker crusher and a high-efficiency classifier); and waste heat cogeneration using AQC exhaust. The amount of energy to be saved will be 61,866 tons/year in oil, promising a 10.9% energy saving and CO2 reduction. The project requires a fund of 5,988,025,000 yen in total. The financial internal rate of return (FIRR) based on the environmental special yen credit is a little low, but the payout period of 11 years is reasonable. A similar result is obtained when export financing by the ex-Exim Bank is studied. A general loan is not proper in view of overall profitability. With precedents showing that it is near impossible for such a project to enjoy environmental special yen credit, it is necessary for the Japanese Government to build a CDM-oriented system under which environmental special yen credit will be offered to private sectors. (NEDO)

  3. FY 1998 basic survey to promote the joint execution, etc. Overall repair plan of thermal power plants in Maritime Province of Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Enkaishu ni okeru karyoku hatsudensho sogo kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For thermal power plants in Maritime Province of Russia, a repair plan for effective reduction of emission of greenhouse effect gas was worked out as a draft plan for the joint execution. The project is to be implemented for the additional installation/replacement of boilers at Vladivostok No. 2 power plant, construction of a power plant as a substitute for Partizansk power plant, and new construction of Ussuriisk power plant. The draft plan includes the new installation of two gas-fired boilers/replacement of existing boilers at Vladivostok No. 2 power plant, construction of 200MW cogeneration facility at Partizansk power plant, construction of 180MW cogeneration facility at Ussuriisk power plant, abolition of small-sized boiler station, etc. The reduction amount of the greenhouse effect gas emission based on this repair plan totaled 338 million tons in project. The effect against cost is US$ 4.75 per 1 CO2 ton at Vladivostok. (NEDO)

  4. Fiscal 1993 survey of the base arrangement promotion for foreign coal import. Survey of the general situation of Thai coal; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Thai sekitan sogo jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the energy situation in Thailand, the present and future status of coal supply/demand, the present situation of environmental policy and air pollution prevention policy and problems concerning coal and the measures for solution, and a possibility of Japan`s cooperation. In Thailand, the total coal supply amount in 1992 is 16.079 million tons, which is 9.1% of all the primary energy supply amount. The country produces only a few amount of anthracite and subbituminous coal beside brown coal. The domestic coal equals brown coal, the production of which was 15.335 million tons in 1992, 13.9% of all the primary energy demand. Concerning brown coal, 79.7% of all the brown coal supply are for electric power use, and others for industrial use such as the cement industry. The remaining reserve in developed areas is 151.4 billion tons, and the proven reserve in undeveloped areas 756 million tons. The demand for import coal was 11.25 million tons in 1996, and is expected to be 201.73 million tons in 2000. The paper pointed out some problems arising from coal production and spread of coal utilization, and described measures to solve the problems and fields where there are possibilities of Japan`s cooperation. 36 refs., 44 figs., 73 tabs.

  5. Fiscal 1999 technical achievement report. Development project on international standards for developing new industry (Comprehensive research); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development of 13 individual subjects whose achievements are expected to come into use on the international scale was started in fiscal 1998, to be completed in three years. Progress is reviewed for each of the subjects, and the findings are mentioned below. Research and development is progressing smoothly, specifications to be internationalized have been narrowed down, and it is now foreseen that the main points of the specifications to be presented will be successfully prepared. There are some subjects, however, about which it is difficult to specify to which technical committees they are to be submitted. Assistance, for instance supply of information, by technical committees involved is indispensable. The attitude toward international standardization taken by European and American business corporations visited for study by Japanese researchers is to be disseminated to Japanese business corporations since the information thus collected will help them. Although 75% of the 13 subjects have reached a level where they may be presented as specifications for international standardization, yet they need active support by organizations concerned and research of trends of internationalization-related institutions before they are actually accepted as international standards. (NEDO)

  6. Report on fundamental investigation in fiscal 2000 of intellectual property right management criteria at General Research Institute of Industrial Technologies; 2000 nendo sangyo gijutsu sogo kenkyusho chiteki zaisanken kanri kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Fundamental items of knowledge were collected on matters to form the base of management and utilization of intellectual property rights as the basic data for cooperation among industry, academia, and government. Activities were put into order on the following nine fields: 1) handling of tangible research property rights at universities, 2) the way the organization should be to support the cooperation between industry and academia - a mechanism at Massachusetts Institute of Technology (MIT), 3) licensing and technology transfer in India, 4) intellectual property trends for the 21st century, 5) management of intellectual property assets - in relation with the new current in the U.S. Patent Act, 6) comparative study of examination guidelines for computer-related inventions between the United States and Japan, 7) management of intellectual properties and business law aspects in the technology innovation times - examples in Seattle where IT and bio-technologies are originated from, 8) patents and bio-technical inventions, and 9) new movements in bio-technology patents. In Item 2), examples at MIT were studied on the way the organization should be to support the cooperation between industry and academia. The industry-academia cooperation is in action at various levels, not only in licensing, but also in the industrial liaison program, and consortiums. (NEDO)

  7. Report on comprehensive surveys of nationwide geothermal resources in fiscal 1979. Conceptual design of a database system; 1979 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Database system gainen sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-31

    Conceptual design was made on a database system as part of the comprehensive surveys of nationwide geothermal resources. Underground hot water in depths of several kilometers close to the ground surface is a utilizable geothermal energy. Exploration using the ground surface survey is much less expensive than the test drilling survey, but has greater error in estimation because of being an indirect method. However, integrating data by freely using a number of exploration methods can improve the accuracy of estimation on the whole. In performing the conceptual design of a geothermal resource information system, the functions of this large scale database were used as the framework. Further data collection, distribution and interactive type man-machine communication, modeling, and environment surveillance functions were incorporated. Considerations were also given on further diversified utilization patterns and on support to users in remote areas and end users. What is important in designing the system is that constituting elements of hardware and software should function while being combined organically as one system, rather than the elements work independently. In addition, sufficient expandability and flexibility are indispensable. (NEDO)

  8. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  9. FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

  10. Experimentation to seek the local speciality in kWh of P.V. system, and a study of its measuring method and instruments and apparatus; Taiyoko hatsuden system no jibetsu hatsudenryo no chiiki tokusei wo motomeru jissho shiken narabini, sono sokutei kansoku no hoho kiki ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Anno, T.

    1997-11-25

    Introduced in this paper are some problems that the author encounters in relation with a 2.6kW photovoltaic power generation system installed at the author`s residence for the purpose of measuring the hourly amounts of generated power. Giving rise to questions in the inverter and the control system are the conversion efficiency under a partial load, the scope of little amounts that are omitted, the maximum power point tracking system and its performance, etc. The author wants to learn how to land on an appropriate conductor thickness and to know the special specifications if any for heavy-snow regions and their effect. Much has been learned from presenters, moderators, and participants at scientific events and through private talks. Although it seems that there exists some relationship between the maximum power point tracking system and the diameter of conductors suitable for the system, yet the manufacturers fail to give clear-cut answers. The author thinks that end-users find many black box-like parts in the system, which the author leaves uncared for now for later study. It is learned that there is no specification intended exclusively for heavy-snow regions. The author`s system is in operation with hourly output recording and data accumulation started. 2 figs.

  11. Study of natural energy system and downward atmospheric radiation. Part 2. Study of downward atmospheric radiation simple estimated formula and elective longwave radiation; Shizen energy system to tenku hosharyo no kansoku kenkyu. 2. Tenku hosharyo kan`i suiteishiki to jikko hosharyo no kento

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, K; Yano, S [Kogakuin University, Tokyo (Japan); Masuoka, Y

    1997-11-25

    With an objective to design and control a natural energy utilization system, this paper describes discussions on a simple estimation formula for downward atmospheric radiation. The simple estimation formula for downward atmospheric radiation using a square root of steam partial pressure, {sigma}T{sup 4} ({sigma} is the Stefan Boltzmann constant, and T is the absolute outside air temperature), and SAT (observation value for corresponding outside air temperature) as explanatory variables was added with data made available further to improve its accuracy. A calculated value, whose formula had observation values at each location substituted, had coefficient of correlation with the observation values of 0.9. This formula was found applicable to each location. The effective radiation amount is the difference between the downward atmospheric radiation and the long wavelength radiation from the ground surface, from which a formula to simply estimate the effective radiation was proposed. Although there is a slight difference, the calculated values derived by using this formula agreed nearly well with the observation values of the effective radiation. A standard SAT meter was used to discuss cooling effect of atmospheric radiation cooling on the ground surface, whereas the cooling effect was verified to appear markedly under windless condition at night. It was found that the cooling effect is more remarkable in winter than in summer. 14 refs., 8 figs., 1 tab.

  12. Applicability of the spatial autocorrection method for estimation of basement structure in Kanto plain. Array measurements of microtremors close to the Iwatsuki and Shimosa deep borehole observatory; Kanto heiya no kiban kozo suitei no tame no kukan jiko sokanho no tekiyosei. Iwatsuki Shimosa jiban katsudo kansokusei ni okeru array bido kansoku

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, T; Umezawa, N; Shiraishi, H [Saitama Institute of Environmental Pollution, Saitama (Japan)

    1996-10-01

    To investigate applicability of the spatial autocorrection method which is a microtremors exploration method for the estimation of basement structure, array measurements of microtremors were performed using the Iwatsuki and Shimosa deep borehole observatory where detailed structures were clarified as well as the Fuchu and Koto deep borehole observatory. In this study, estimated velocity structures of S-wave were compared with the geological sequence and results of acoustic velocity logging. The phase velocity was estimated by the spatial autocorrection method using FFT. The phase velocity with a smooth normal dispersion was observed in the periodic range from 0.5 to 5 sec in Iwatsuki, and from 0.5 to 4 sec in Shimosa by the combination of four-point circular arrays with radii of 100, 300, and 600 m. The underground structures estimated from the phase velocities coincided well with the geological sequence, and results of acoustic velocity logging and velocity logging for each borehole. For the Iwatsuki borehole, the basement velocity was also estimated properly in the periodic range of observation. While, for the Shimosa borehole, measurements with the period around 6 sec were required to estimate the basement velocity more accurately. 13 refs., 11 figs., 1 tab.

  13. Fiscal 1974 Sunshine Project result report. R and D on solar energy system (weather survey). Part 3. Observation data on global solar radiation and sunshine duration; 1974 nendo zenten nissharyo, nissho jikan no kansoku shiryo. 3. Taiyo energy system no kenkyu kaihatsu (kisho chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    This report includes observation data on global solar radiation and sunshine duration for R and D on solar energy system. The global solar radiation data include the following measured by bimetal pyranometer in 1954-1970: Monthly and yearly mean value, average value, standard deviation, coefficient of variation, and maximum and minimum value. The sunshine duration data include the following measured by Jordan's heliograph in 1941-1970: Monthly and yearly total value, 10-year mean value, average value, standard deviation, coefficient of variation, and maximum and minimum value. Annual variations of the global solar radiation at 16 typical sites all over the country are illustrated using the average values, and secular variations of the monthly and yearly mean values at 16 sites are also illustrated. Annual variations of the sunshine duration at 17 typical sites are illustrated using the average values, and secular variations of the monthly and yearly total values at 17 sites are also illustrated. Profiles of the global solar radiation and sunshine duration, and their coefficients of variation are illustrated for every country. (NEDO)

  14. Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

  15. Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

  16. Fiscal 1993 study of engineering for making areas prosperous using natural energy; 1993 nendo kankyo chowagata green techno system no kokusai kyoryoku model ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper studied the engineering for activating areas using natural energy. A system has started in which electric power companies purchase surplus electric power from the natural energy use power generation such as the wind power and photovoltaic power generation, etc., and a lot of local self-governing bodies in the country plan `projects to promote town` using the system. However, few engineers and makers can plan `a project to promote town,` making effective use of natural energy which is fickle. Therefore, first, the paper arranged the actual status mostly of the cases of `the projects` using natural energy which have been carried out in the country. Next, the trend of the natural energy utilization technology in countries including the U.S. was described. Moreover, assuming model areas in Japan for working out a concept of model projects on the natural energy utilization and town promotion, a concept was proposed making full use of the utilization technology which has now usability. Arrangement is being made for conditions for the full scale spread as seen in the subsidy system for general users. 3 refs., 176 figs., 61 tabs.

  17. Fiscal 1999 survey report. Survey of effect of energy efficiency improvement on global environment; 1999 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Analyses are conducted into consideration given to global warming measures in the 3rd assessment report of the Intergovernmental Panel on Climate Change (IPCC) and into technology transfer from developed nations to developing nations in the Asia-Pacific region etc. to contribute to their energy efficiency improvement. The aim is to present data for deliberation as to how future energy efficiency improvement measures should be in the Asia-Pacific region. The chapters (Chapter 0 through Chapter 10) of the report to be worked out by Working Group III deeply involved in energy problems are 0) Introduction, 1) Scope of the report; 2) Socio-economic and emissions scenarios; 3) Technical and economic potential of GHG (greenhouse gas) emissions reduction; 4) Technical and economic potential of biological CO2 mitigation options; 5) Barriers, opportunities and market potential of technologies and practices; 6) Policies, measures and instruments; 7) Costing methodologies; 8) Global, regional and national costs and ancillary benefits of mitigation; 9) Sector costs and ancillary benefits of mitigation; and 10) Decision making frameworks. As the result of the survey, some actual technology transfer implementations are introduced covering branches closely related to energy efficiency improvement, which are branches of construction, traffic, industry, energy supply, and wastes. (NEDO)

  18. Report on achievements in fiscal 1998. Survey on environmental effects from photovoltaic power generation systems; 1998 nendo daikibo taiyoko hatsuden system no kankyo eikyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Different environmental effects may be assumed when large-size photovoltaic power generation systems are installed in vast unutilized lands including deserts. Knowledge having been acquired to date has been put into order on the following subjects as the pre-survey thereon: (1) environmental characteristics of desert areas, (2) discussions on environmental effects from (a) environmental assessment viewpoints, (b) contents of the environmental assessment, and (c) environmental assessment institutions, and (3) the survey policy. In discussing the environmental characteristics, it is revealed that desert areas are neither sterile nor unused, but pasturage and agriculture have been carried out in historical and traditional ways. In discussing the environmental effects, it was recognized that surveys on primary and secondary effects on the environmental are indispensable. With regard to the institutions, there are countries who have and have not the institutions even among the OECD member states. In addition, it was known that environments in the desert areas vary greatly according to the particular areas, whereas there are possibilities of installing the facilities because the effects of the facility locations on the environment are various. Therefore, it was decided to start from the case studies in locations of different types. (NEDO)

  19. Report of the researcher exchange promotion project on the environmental issues in the Asia-Pacific region; Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Proposals have been made for the establishment of a network (ETERNET-APR) linking those involved in the research and development of environmental technology in the Asia-Pacific region in order to limit the environmental impact of industrial activity. By pursuing active exchanges of information and personnel, researchers in environmental technology in the Asia-Pacific region have been making serious efforts to establish such a network. This fiscal year, the Internet Web site of the ETERNET-APR has been created using the data collected to date. This database includes information on some 350 researchers and 200 research projects from seven countries. The first international symposium was successfully held at Environmental Research Institute of Chulalongkorn University in Thailand (ERIC), hosting 200 environmental researchers from 10 countries in the Asia-Pacific region. Tripartite sister laboratories ties among the National Institute for Resources and Environment (NIRE) and three Korean laboratories were forged. The sister laboratory project between ICETT and ERIC is also proving effective. These successes prove that intraregional joint research, the objective of ETERNET-APR, has begun to take shape in this year

  20. Study on the creation of inorganic materials using micro-gravity environment; Bisho juryoku kankyo riyo muki zairyo no sosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Creation of new functional inorganic materials using micro-gravity environment was studied. Observation of an electrode interface phenomenon under micro-gravity clarified that time variation in interference fringe is dependent on current density and electrode thickness in ground experiment, while it is dependent on not electrode thickness but current density under micro-gravity. In fabrication of glass fine particles under micro-gravity, true spherical glass fine particles of 4-7{mu}m in size were obtained corresponding to a charge of 40mg by evaporation and solidification of sodium tellurate glass as raw material under micro-gravity. In fabrication of non-harmonic Pb-Zn system alloy, the homogeneous alloy texture of 5{mu}m level was observed which has never been observed in previous metal phase diagrams by fusion of 80atom%Pb-20atom%Zn mixture under micro-gravity and quenching from 500degC. On the study on fabrication of spherical semiconductor crystals, 7 spherical Si single crystals of 300{mu}m in size were obtained. 12 refs., 48 figs., 2 tabs.

  1. Achievement report for fiscal 1998. Development of environmentally friendly universal controller; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances. An environmentally friendly UC is a remote controller which utilizes an infrared two-way communication function and becomes capable of dealing with any appliance upon downloading remote control information from the appliance involved. Studies were conducted for the development of controller hardware and software therefor and for the development of electrical home appliances to correspond to their specifications. In relation with energy conservation, studies centered about reduction in power consumption while on standby and unnecessary power consumption. As the result, an environmentally friendly UC protocol was newly developed and, based on the protocol, plural numbers of controllers, appliances, and network gateways were tentatively fabricated, and were examined for their function, behavior, and operational interchangeability. Systems aiming at reducing power consumption while on standby and unnecessary power consumption were built by way of experiment, and were checked for performance. It was then concluded that a reduction of several billion kWh might be achieved. (NEDO)

  2. Study on the impact assessment for the life cycle assessment (LCA); Kankyo fuka bunseki ni okeru impact assessment ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes the impact assessment which is an important step for LCA. For classification of the impact assessment, the existing literature was reviewed and a skeleton for the classification was proposed. The weighting factors for nine selected impact categories, which were used to calculate environmental load point (ELP) for the valuation, were obtained for two overseas groups, i.e., students of Amsterdam University and SETAC Europe members. It was found that the former provided the similar trends to general Japanese, however that the latter gave high weighting in the global warming and depletion of ozone layer. The ELP was proposed and applied to automatic washing machine, coffee maker, waste incineration power generation system, and co-generation system. As a result, its effectiveness was demonstrated. This report also describes problems for the LCA of thermal and material recycling of PS trays. 99 refs., 96 figs., 73 tabs.

  3. Survey on chemical engineering technologies for the global environmental protection; Chikyu kankyo hozen no tame no kagaku kogakuteki taisaku gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    The present paper suggests chief measures to suppress and reduce global greenhouse gases. Under the control of artificial environments such as bioreactor, hydroponics and vegetable factory, a very high fixing rate of CO2 can be obtained, but CO2 generation accompanying electric power consumption is also large. It is preferable to use methane as resource by reforming reactions or selective oxidative reaction. In the recovery technique of fluorocarbon, 100% recovery is desirable. Techniques for decomposing recovered fluorocarbon and converting it to harmless material are the most backward ones. Understanding of essential structural relationship of coal is necessary for establishing combustion technique for the reduction of N2O. The integrated power generation system composed from solid electrolyte type fuel cell and coal-gasifying process, high-performance, superheat pump system form scientific technology imposing no burden on the global environment. Establishment of purification technique for industrial- or living-related drain inflowing to a closed water area system, establishment and reinforcement of inspection system for oil spill in the oceans in a global scale are required. 240 refs., 63 figs., 30 tabs.

  4. Takane new energy vision. Creation of life environment with affluence using natural energies; Takane shin energy vision. Shizen energy wo ikashita yutakana seikatsu kankyo no sozo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision was established that discusses how the way the new energy introduction consistent with district characteristics should be, and has at the same time the leadership and specificity. Takane Town in Yamanashi Prefecture is a town located in the south skirt of Mt. Yatsugatake, having a population of about 9400 and households of about 3200. The town consumes energies converted into petroleum of about 19,000 kL/year. The activity achievements were put into order by the following five items: 1) what is the new energy vision?, 2) district characteristics, 3) the basic plan, 4) plans placed with emphasis, and 5) promotion of the vision. Item 4 includes introduction of new energies into the welfare, education and cultural facilities, utilization of bio-mass energy using livestock resources, introduction of new energies into the Hananomori Park at South Yatsugatake, introduction of clean energy fueled automobiles, and small hydropower generation utilizing clean streams in the Kiyosato area, introduction of new energies into the Kiyosato Station square, introduction of next generation agriculture utilizing new energies, and communications with nature and ecology of Takane Town. (NEDO)

  5. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  6. To the fusion of age - economy and ecology of the ring industry revolution; Kankyo kakumei no jidai {approx}ekonomi to ekoroji no yugo he

    Energy Technology Data Exchange (ETDEWEB)

    Akaike, Manabu

    1999-05-31

    What has suddenly been noticed as a keyword of the durable industry creation in which the ecology is made to be compatible with the economy is a philosophy of {sup t}he bio region (the life regionalism){sup .} As the concepts of region management desired at present, the philosophy of bio region which is the thought of the next generation development which I notice at present most roots in the place where selves live, and it aims at uniting with the region. In the reason, it is required that natural resources such as climate, land form, basin, soil, microorganism, flora and fauna, resources that the region has are utilized maximally. (NEDO)

  7. Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

  8. Investigations on an environment friendly chemical reaction process (eco-chemistry). 2; Kankyo ni yasashii kagaku hanno process (eko chemistry) ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In order to structure a chemical reaction process that does not discharge a large amount of waste by-products or harmful chemical substances, or so-called environment friendly process, investigations and discussions were given based on the results derived in the previous fiscal year. A proposal was made to reduce environmental load on development of oxidized and dehydrogenated catalysts that can produce selectively ethylene, propylene and isobutylene in an oxidation process. In liquid phase oxidation, redox-based oxidation and solid catalyzation of automatic oxidation reaction were enumerated. In acid base catalyst reaction, development of ultra strong solid acid was described to structure no pollution discharging process. In the fine chemical and pharmaceutical fields, the optical active substance method and the position-selective aromatics displacement reaction were evaluated to reduce environmental load. A questionnaire survey performed on major chemical corporations inside and outside the country revealed the following processes as the ones that can cause hidden environmental problems: processes discharging large amount of wastes, processes treating dangerous materials, and processes consuming large amount of energy. Development of catalysts is important that can realize high yield, high selectivity and reactions under mild conditions as a future environment harmonizing chemical process. 117 refs., 23 figs., 22 tabs.

  9. Fiscal 1994 survey report. Survey of energy supply/demand structure sophistication and global environmental impact; 1994 nendo energy jukyu kozo kodoka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Outlines of various energy supply/demand analytical models are surveyed. With environmental problems gathering importance, a number of models are being introduced in which energy supply/demand structures, long-term climate changes, and impacts of policy options on social economy are linked to each other. Some socioeconomic impact models cover a single country and others the whole world. They are various in type, ranging from dynamic optimization models to static balance models. Twenty-four models are chosen, and grouped into two types respectively covering Japan and the whole world from a geographical viewpoint and into three groups in view of their structures. Under an optimization model, such optimization is accomplished as economic growth maximization and energy cost minimization and so forth under given energy supply restrictions. Under a general balance type econometric model, an adjustment process in which capital and labor and production are coordinated across multiple departments is expressly stated. Under a partial balance type econometric model, a demand function for goods is given and optimum behavior such as consumption maximization is indirectly described. (NEDO)

  10. FY1995 study of design methodology and environment of high-performance processor architectures; 1995 nendo koseino processor architecture sekkeiho to sekkei kankyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The aim of our project is to develop high-performance processor architectures for both general purpose and application-specific purpose. We also plan to develop basic softwares, such as compliers, and various design aid tools for those architectures. We are particularly interested in performance evaluation at architecture design phase, design optimization, automatic generation of compliers from processor designs, and architecture design methodologies combined with circuit layout. We have investigated both microprocessor architectures and design methodologies / environments for the processors. Our goal is to establish design technologies for high-performance, low-power, low-cost and highly-reliable systems in system-on-silicon era. We have proposed PPRAM architecture for high-performance system using DRAM and logic mixture technology, Softcore processor architecture for special purpose processors in embedded systems, and Power-Pro architecture for low power systems. We also developed design methodologies and design environments for the above architectures as well as a new method for design verification of microprocessors. (NEDO)

  11. Report on surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology; 1999 nendo kankyo chowagata shokubai gijutsu no kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the surveys in fiscal 1999 on research and development of the environment harmonizing catalyst technology. The discussion subjects taken up included suppression of discharge of carbon dioxide, catalysts used when manufacturing hydrogen and technology thereof, and environment purifying catalysts to decompose harmful substances, and technology thereof. The roles of catalysts and their technologies are expected in reducing the reforming temperatures, achieving energy saving, and reducing decomposition energy. Furthermore, the catalysts are expected of high activity, long life and low cost. Three themes were selected from the emergency and importance points of view. The themes are, in the consumer field, research and development of efficiency improvement in membrane reactors for reforming low-grade hydrocarbons to structure a technology to manufacture hydrogen for small-size portable fuel cells; and in the industrial field, development of hydrogen and carbon product manufacturing technologies with which CO2 generation is suppressed by means of the catalytic decomposition process. In practice, for such discharged harmful substances as dioxins, PCB and volatile organic compounds (VOC), treating them is the urgent environmental problem, and therefore, the fundamental research was taken up for practical application of the second-generation catalysts of the ultra-violet light and visible light responding type. (NEDO)

  12. International symposium on environmental impacts of advanced alternative to CFC; CFC shinki daitai busshitsu no kankyo eikyo ni kansuru kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-07

    The international symposium on environmental effects of new CFC substitutes was held in Tsukuba City, Ibaraki Pref. on February 7-9, 1996, and 19 papers were made public. In Session 1 (Plenary lecture), reports were made on Global warming and climate change: a review of recent studies; Stratospheric ozone, CFCs, and CFC-substitutes: an update, etc. In Session 2, Measurements of OH rate constants for advanced refrigerants as well as HCFCs and HFCs; The reaction rate of CFC alternatives with OH radical; Experimental and estimated rate constants: reactions of hydroxyl radicals with several halocarbons, etc. In Session 3, Measurement of uptake coefficients of some acetyl halides and fluorinated ethers into water; Mass transfer at the air/water interface: removal processes of halocarbonyl compounds; Heterogeneous reactions of fluorinated ethers on allophane or titanium dioxide, etc. In Session 4, papers were reported on model calculations relating to the global warming.

  13. Evaluation of corrosivity of the vapor-phase environments to sterilized water with chlorine; Enso kei mekkin shorisui no kisho kankyo no fushokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakata, Michio. [Nippon Steel Corp. Yamaguchi (Japan). Technical Development Bureau

    1999-08-15

    Corrosivity of vapor-phase aenvironments in indoor pool, water thank, and water purification plants was investigated. Sodium hypochlorite (NaClO) was used as a sterilizing agent in indoor pool, while chlorine gas was used in water tank and water purification plants. It was found that Cl{sup -} ion were concentrated in the dew formed in the indoor pool. H{sup +} ions as well as Cl{sup -} ions were accumulated in the dew dormed in the water tank ans water purification plants. Thus, the corrosion condition was varied with the type of sterilizing agents used. Through the investigation of water tanl, the relationship between pH and Cl{sup -} ion concentration was given as follow; pH=-1.09-2.19 log [Cl{sup -}] (mol/L). Corrosivity of vapor-phase enviroments in sterilizing water systems would be characterized by the exstence of oxidizing chemical agents such as ClO{sup -} and HClO, the shift of corrosion potenrial of the thin water film, and the accumulation of H{sup +} and/or Cl{sup -} ions in the dew. (author)

  14. Survey on synthesis and reaction of environmentally benign water-soluble metal complex catalysts; Kankyo chowagata suiyosei sakutai shokubai no gosei hanno no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes the research trend survey results on the synthesis and reaction of water-soluble metal complexes which are regarded as environmentally benign catalysts. For the synthesis and catalysis of water-soluble complexes, synthetic methods of water-soluble phosphines, such as sulfonated TPPMS and TPPTS, are described in detail. Synthesis and reactivity of hydroxymethylphosphines are introduced, and the application of electrospray mass spectroscopy is elucidated as a tool for the analysis of them. Changes of the application of transition metal complexes with water-soluble phosphines to catalysis are described. Dual catalysts which have both functions of phase transfer catalysts and homogeneous catalysts are introduced. Concept of counter phase transfer catalysts is also introduced, and some catalytic reactions are described. In addition, this report introduces catalysis of water-soluble polymer-supported metal complexes, immobilization of metal colloids with water-soluble ligands and their analysis, and water-soluble complexes as hybrid catalysts. 144 refs., 94 figs., 10 tabs.

  15. Research and development of environment measuring laser radar. 6. Follow-up; Kankyo keisokuyo laser radar no kenkyu kaihatsu. 6. Follow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In an effort to extend cooperation for reducing pollution in urban areas in the Asia-Pacific Region, a laser radar system was constructed in the city of Djakarta, Indonesia, in 1996, and a follow-up started in fiscal 1997. The aim is to collect information necessary for atmospheric environment improvement through observing pollutant distribution and movement in the upper atmospheric layers over the city. Mie-scattering lidar (laser infrared radar) observation has uninterruptedly been on since the summer of 1997, the system collecting data about Djakarta's atmospheric boundary structure throughout the year. The data indicate great changes in the atmospheric boundary structure between the dry and rainy seasons. The result of intensified observation conducted in the dry season shows that the altitude that the mixed layer reaches in the inland region is higher in the daytime and lower in the nighttime. It is necessary to compare the result with atmospheric pollution data collected on the ground surface and determine the relationship between the behavior of pollutants and the circulation of land-and-sea breeze. The data of September, 1997, reveal an aerosol layer at altitudes of 2km and higher, and this is attributed to forest fires. The result of intensified observation conducted in the dry season of 1998 is also stated. (NEDO)

  16. Project to promote the technical development of global environmental industries. International research exchange project; Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Exchanges with researchers/research institutes in overseas countries have an important meaning in promoting the research and development toward the creation of new research fields where the solution to the environmental problem is aimed at and toward the construction of new technological systems. Therefore, under the cooperation of Research Institute of Innovative Technology for the Earth (RITE), and RITE related researchers and societies, given were invitation and dispatch of researchers to international conferences and symposia involved in the global environment related technology, and exchanges with major overseas research institutes/universities. At the same time, based on the short-term invitation and dispatch so far given, a system was established for medium- and long-term dispatch/invitation of researchers who are thought to hold an important position in the future research activities. From the results obtained, domestic and foreign exchanges relating to the latest research could be promoted. In addition, researches in the basic domain related to the global environmental technology were advanced in a variety of fields overseas. The numbers of invitation and dispatch given in fiscal 1995 were 12 and 13, respectively, the results of which were included in this paper. 121 refs., 74 figs., 11 tabs.

  17. Ecological concepts in recent polymer technology. Part4. Eco-friendly water-absorbing polymer; Kankyo ni chowa shita kyusuisei kobunshi

    Energy Technology Data Exchange (ETDEWEB)

    Kunioka, M.

    1997-07-01

    As an application example of water-absorbing polymers with biodegradability, it was expected to be applied to soil improvement agents used in planting trees in deserts, besides physiological napkins, paper diapers and medical materials. In this paper, water-absorbing polymers with biodegradability such as natural polymers, petroleum-made polymers and polymers synthesized by radiation cross-linking and chemical cross-linking were introduced. Moreover, a kind of water-absorbing polymers developed by the authors, made from polyamino acid synthesized by microbes, was introduced. In the method developed by the authors, the cross-linking structure could be made by combining PGA carboxyl groups and various amino groups of diamine using carbimide with water solubility. As for this method, all of reactions could be conducted in water and catalytic replacement was not necessary, moreover, hydrogel with the water-absorbing rate of 200 to 1500 times could be produced. 44 refs., 3 figs., 1 tab.

  18. New energy vision at Sabae City. Toward realization of 'environmental international city'; 2001 nendo Sabae shi chiiki shin energy vision. Kankyo kokusai toshi Sabae no jitsugen ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    With an object of accelerating introduction of and uplifting consciousness on new energies at Sabae City in Fukui Prefecture, a new energy vision was put into order based on the result of the initial stage investigation having been performed in the previous fiscal year. Solar light and solar heat energies will be introduced positively into public facilities, and at the same time works will be implemented to accelerate the proliferation thereof into general households. The target of introduction by the year 2010y is set to 2,600 kW by photovoltaic power generation, and the introduction thereof is planned to schools, nursery schools, municipality operated houses, and unattended facilities. With regard to solar heat water warmer, the present proliferation rate of about 7.3% will be raised to 15%. Regarding wastes generated from industrial areas, efficient energy extraction by thermal recycling is intended on the assumption of suppression of wastes generation, their re-use, and recycling. Systems may include the bio-gas system, cogeneration, and recovery of energies from plastics wastes. For acceleration of proliferation of new energies in general, promotion of introduction will be achieved on mini-wind power generation, small hydroelectric power generation, and fuel cell automobiles. (NEDO)

  19. Research and development cooperation project on environmental measurement using laser radar in fiscal 1994; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper outlined activities in fiscal 1994 in the R and D cooperation project on a laser radar for environmental measurement. In the activities in fiscal 1994 of `the ODA laser radar development committee,` the committee held four meetings, two field surveys were carried out, and two researchers were invited from Indonesia. In the field survey, the environment in Jakarta city was investigated in terms of changes in population and number of the cars registered. Further, from data collected during 1994-1998 in the central Jakarta city, the following were made clear: the trend of a decrease in SO2, the trend of a rapid increase and an excess of NO2 content over the environmental standard, the status of pollution of which the level is close to the upper limit of the environmental standard of dust, etc. In the meeting of the policy study for the field survey at LIPI headquarters, Japan proposed a system which is constituted of a difference absorption laser radar, two Mie scattering laser radars, and a central processing unit. The sites proposed were studied in cooperation with Indonesia. 40 refs., 65 figs., 9 tabs.

  20. FY 2000 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 2000 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Looking for effective measures for enhancement of energy consumption efficiency in the Asia Pacific region, survey was made of the state of study of measures against global warming in the 3rd IPCC report and the state of study of the incidental convenience. The survey was made in the following two fields: 1) research analysis in study of the 3rd IPCC report; 2) research analysis of the convenience incidental to measures against global warming. 1) is composed of IPCC activities and the 3rd assessment report, and the developmental state of global warming prevention technology and potential of greenhouse effect gas reduction. Subjects on the prevention technology are the technology for enhancement of energy consumption and development of non-fossil fuels. Physical/chemical CO2 fixation is also studied. 2) is composed of the introduction, economic/social/environmental effects, international flow, reasons for different conclusion in every study, and fields of further study. Considered were global warming prevention measures, for example, economic/social/environmental effects of creation of the carbon tax, reduction in subsidy in energy sector, etc. (NEDO)

  1. Research and development cooperation project on environmental measurement using laser radar in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    As one of the international research cooperation projects, the research cooperation in developing laser radar for environment measurement started between Japan and Indonesia. The project is scheduled to be carried out in a 4-year plan starting fiscal 1993. In fiscal 1993, conducted were negotiations with Indonesia on its implementation and a field survey. Between January 6 and 15, 1994, the first field survey was made in terms of topography, climate, road network and traffic situation of Jakarta city, and the proposed sites for installation were reported. The paper also introduced the reception system on the Indonesian side and a request for technical learning through stay in Japan. The second field survey was conducted between February 27 and March 6, 1994. Indonesia requested that they want to make laser radar observation not only for the local area, but the one that covers industrial areas, central urban areas and residential areas. Incidentally, there was an opinion that it is important to elucidate the pollution mechanism. 19 refs., 43 figs., 6 tabs.

  2. Survey on problems in developing technologies for the global environment issues (Version II); Chikyu kankyo mondai gijutsu kaihatsu kadai chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-07-01

    This paper describes a survey on problems in developing technologies for the global environment issues. Technological development of means to reduce generation of environmental issues and substitutive means for non-generation thereof is being moved forward specifically in the Sunshine Project and the Moonlight Project. The Chemical Technology Research Institute assumes that it has a responsibility to positively contribute to developing a technological system that matches the substance circulation mechanism of the earth from the fields of chemistry. Therefore, the Institute has organized working groups that have been identifying problems from their expertise standpoints and have been extracting study assignments. Subsequent to the Version I, the Version II has been compiled. The Version II takes up the simulation of global warming mechanisms, behavior of gases dissolved in oceans, and possibility of fixing CO2 in oceans. With respect to fluorocarbons, the Version II describes development of substitutive substances, their stability, combustion method as a destruction technique, and destruction by means of super criticality. Regarding CO2, the version introduces technologies to re-use CO2 as a resource by means of membrane separation, storage, and contact hydrogenation. The volume also dwells on CO2 reduction by using photo-chemical and electrochemical reactions, CO2 reduction and photo-synthesis by using semiconductors as photo catalysts and electrodes. (NEDO)

  3. Achievement report for fiscal 1998 in developing environment corresponding universal controller (Individual report edition); 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Kobetsu hokokuhen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Research and development has been performed on an 'environment corresponding universal controller (UC)' that realizes 'easiness of use and energy conservation' in correspondence with household electric appliances. This paper summarizes the reports by themes. The summarized development themes include: 'development of a bi-directional controller and TV interface', 'development of a bi-directional remote controller, an infrared ray to radio converter, and an air conditioner corresponding to the bi-directional remote controller', 'development of a UC corresponding air conditioner, and electric power cable transporting gateway', 'development of a universal controller and a control box', and 'development of an energy saving wiring system for the UC remote controller'. This paper also summarizes the works done by research participating departments of each corporation, such as development of UC corresponding video and TV sets (Sanyo Electric), development of UC corresponding TV sets (Toshiba), development of a UC corresponding DVD player (Japan Victor and Victor Techno-brain), and development of a UC relay box and a control box for the existing HA system (PANA R and D). (NEDO)

  4. Research report. Environmentally friendly energy community research business for Fujieda district (Refuse energy utilization); Fujieda chiku kankyo chowagata energy community chosa jigyo (haikibutsu energy riyo shisetsu) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An environmentally friendly refuse energy utilizing business, for which RDF (refuse derived fuel) produced out of wastes discharged by industries belonging to a Fujieda city environmental protection council will provide the heat source, is proposed by the said council. The proposal is subjected to a study, a basic plan is drafted, and a decision is made on its profitability. In the study, surveys are conducted on the actualities of wastes and of demand for heat, and specifications are worked out relating to transportation and storage of RDF, production of steam by an RDF-fired boiler, routing of pipes for transmitting the steam to the industries in the district, facility costs, operating costs, etc. It is found that the amount of RDF produced out of the wastes discharged by the council member industries is so small that it can meet the demand of only one industry and that, even if more wastes are collected from a wider area, the increased amount will but meet the demand of two industries and a hot water pool. It is found that the system will be economically feasible, however, if the shortage of RDF-generated energy is covered by an oil-fired boiler and thereby impartiality is established in steam distribution and steam production unit price is reduced. In view of the intensification of control over dioxin, etc., the business will be gaining profit in 2002 and after. (NEDO)

  5. Fiscal 1999 report on international joint research project on global environmental technology; 1999 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As part of the above-named effort, Japanese researchers were dispatched to overseas universities and laboratories for implementing joint researches into 11 subjects selected by the NEDO (New Energy and Industrial Technology Development Organization) screening committee. When the feedback of fruits of the researches to NEDO projects is taken into account, it may be said that the accomplishments, attained relative to the development of processes for the practical application of environmentally-friendly biomass energy and measures for promoting its adoption, will contribute to the completion of an environmentally-friendly energy production process, excellent in CO2 emissions reduction, in which biomass will be the raw material. In relation to the technology of installing pipes for CO2 discharge into the ocean, some of the dispatched researchers had an opportunity of studying technological problems not deal with under NEDO research and development projects. In the study of organized structures of low-purity CO2 bubble groups, a great contribution was made to the promotion of the NEDO-implemented project of evaluating the impact of CO2 storage in the ocean upon environments. The development of remedial technologies for Microcystis aeruginosa-invaded lakes by introducing environmental engineering assumes a very important position in the endeavors for environmental improvement in developing nations in the Asia-Pacific region. (NEDO)

  6. Assessment of global environmental impacts by utilizing methodology of LCA on solar water heater for dwellings; LCA shuho ni yoru taiyonetsu onsuiki no kankyo fuka hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Kamoshida, J [Shibaura Institute of Technology, Tokyo (Japan); Asai, S [Yazaki Corp., Tokyo (Japan)

    1997-11-25

    CO2 emission was quantified through the life cycle of a solar water heater to assess its environment impact. Although LCA (life cycle assessment) originally sums up I/O of all materials and energy through the whole life cycle of a product to examine environment impact, this assessment was carried out for only CO2. Calculation of CO2 emission assumed a natural circulating solar water heater of 200 l in effective hot water capacity, 2.78m{sup 2} in effective collecting area, and 0.5 in average annual collecting efficiency of total solar radiation, and an auxiliary city gas heat source for compensating insufficient heat quantity. The total CO2 emission in the life cycle of a solar water heater was obtained from an industrial association table assuming the life cycles of 10 and 20 years. CO2 emission was estimated to be 5407.1kg-CO2 and 10665.2kg-CO2 for 10 and 20 years, respectively. CO2 emission due to city gas was largest in the total CO2 emission in the life cycle. As a result, for reduction of CO2 emission due to a solar water heater, improvement of equipment efficiency was most important. 6 refs., 5 figs., 3 tabs.

  7. Activity of environmental, safety and hygiene on Dainippon Ink and Chemicals, Inc., Tokyo plant; Dainippon Ink Kagaku Kogyo (kabu) Tokyo kojo no kankyo hoan katsudo

    Energy Technology Data Exchange (ETDEWEB)

    Nagai, T. [Dainippon Ink and Chemicals, Inc., Tokyo (Japan)

    1998-06-15

    This plant exists along Route 17 in Itabashi-ku, Tokyo adjacent to Saitama prefecture, and started operation in Nov. 1937 to produce printing ink, varnish for ink, paint for cans, paint for PCM and paint for incombustible building materials. Five hundred employees and more than 100 stationed workers from cooperative companies work in the plant. Disasters of the plant are drastically on the decrease. The plant achieved a non-disaster duration of nearly 9.7 million hours, and no accidents and disasters for nearly 10 years at the end of Feb. 1997. Safety and quality control are in promotion by top-down system through the organization and bottom-up activity by small groups. The experience meetings of safety and QC circle activities are held in spring and autumn every year to spread the results among employees. In addition, selective activities are made by top-down system at marked points to prevent accident and disaster, and a mannerism in circle activity. Environmental ISO was also introduced for further improvement of an environmental protection control system. 1 fig.

  8. Survey report on an environmental harmony type production system of chemical products; Kankyo chowagata kagaku seihin seizo system ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As part of establishing an environmental harmony type production system of chemical products, study and survey were made on PET bottles. Using the life cycle analysis method (LCA), a study was made for proposing a material recycle (MR) method which is environmentally and economically excellent in the stage of recycling waste PET bottles. The total cost of recycling can be reduced by 34% supported by a decrease in equipment cost and improvement in yield if there is no mixture of foreign substances such as aluminum caps and PVC bottles. However, the ratio of the amount obtained from the reduction to the total production cost is small, and it is necessary to take measures from a viewpoint of the cost in a total production process and environmental loads. In a survey in Kawaguchi city, PET bottles discharged from the business sector occupied 41% of all the discharge amount. In a survey in Yokohama city, very important data were obtained on PET bottles appointed as the second type under the recycle law. The quality of PET bottles to be brought to the recycling plant is important for effectively processing PET bottles in MR method. For achievement of MR which is low in cost and small in environmental load, needed were cooperation by citizens, the shipping management system in autonomous government, and changes in design and material quality to be made by the industrial circle. 8 refs., 64 figs., 68 tabs.

  9. Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

  10. FY 2000 report on the results of the research study of environmental information network; 2000 nendo kankyo joho network ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the research study on environmental information network formation. The Internet is experiencing an explosive increase in volume of information distributed therethrough. This is accompanied by increased problems related to information searches, information exchange security and information-reliability guarantees. First in demand are excellent portal sites, and second are sites that can be relied on to responsibly provide information. Cooperation with the real world off the Net is of particular importance, because the operating organizations, e.g., sites, will lose their raison deter, unless they clarify their unique abilities and characteristics under the tendencies towards broadened bands and ubiquity. The public sector, on the other hand, is highly reliable, accumulates a large volume of information, and has high network capacity. It has various functions, e.g., supporting the activities pertaining to ISO standards, and promoting the activities, e.g., those for educational programs, interdisciplinary exchanges by researchers, and matching of various organizations. The international cooperation for environmental information needs construction and operation of the networks, and construction of the infrastructures in the developing countries. If information becomes more ubiquitous, a chaotic sea of information will result. NEDO is strongly obliged to serve as the beacon, because it has established a huge volume of environment-related technologies, information, and networks. (NEDO)

  11. Achievement report for fiscal 1998. Development of Assessment Technology of Life Cycle Environment Impacts of Products; 1998 nendo seika hokokusho. Seihinnado lilfecycle kankyo eikyo hyoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An inventory data collecting format is formulated, data collecting activities are launched through 23 industry associations and several investigatory agencies, and almost all the primary data are collected. All the inventory items are being rearranged into a convenient order, and efforts are under way to designate the association to be in charge and the method to be used for data collecting (the accumulation method, process model method). Problems about techniques in the veinous department are extracted. The flow of matters relating to various metals and glass after their use and the magnitude of their environmental impacts at the ultimate sites of treatment are understood though roughly. Investigations are conducted into typical formats overseas, a data arranging format is constructed, specifications are defined for a data inputting software program, and a request is placed with a dedicated dealer for the compilation of the said program. The architecture and specifications of an LCA (life cycle assessment) database system are determined, and its functions are undergoing an intermediate check by a research team for improvement. Endeavors are exerted at quantifying global warming, ozone layer depletion, biotoxicity, and photochemical oxidants for use as the basic data for damage evaluation. (NEDO)

  12. Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

  13. Research information network survey of innovative technology for the earth. 2; Chikyu kankyo taisaku gijutsu no kenkyu joho network chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In order to construct the information network system for a research of innovative technology for the earth, a prototype has been made. To draw necessary functions for the information network system, an information flow in a general research work is analyzed to classify it based on the functions. The information collecting function, information accumulating and sharing function, special information system for research, information providing function, and communication function of the net work correspond to the collecting information, accumulating information, being engaged in research, providing information, and communication of researcher`s actions, respectively. The services on network system supposed from these functions are the homepage search mailing list, intranet service, special information system for research, WWW Internet broadcasting, and BBS/news/conference tool, respectively. It was found that latest Internet technology enabled to construct easily controlled system environment for users and WWW would develop as a standard communication tool. 2 refs., 26 figs., 27 tabs.

  14. Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

  15. Research on the information network for R and D on the innovative technology for the earth; Chikyu kankyo taisaku gijutsu no kenkyu joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to structure an information network system to promote research information exchange on global environment preserving technologies, the currently used RITE information system was reviewed, and the WWW home page was discussed. Three years have passed since the structuring of the RITE information system, during which remarkably popularized use of the Internet can be seen. With respect to provision of research information through the Internet, IP connection is possible in almost all the countries; a variety of research information utilizing WWW are provided; multi-media functions are advancing in image information, audio information and animated image information; and retrieval servers are improved according to applicable fields. Regarding the RITE information system, discussions are given on improvement in the Internet access environment, and expansion in information providing scope and information exchange environment. A WWW home page was prepared on a trial basis, which indicated that a considerable amount of information can be provided even under the presently retained information and the current network environment. 2 refs., 28 figs., 3 tabs.

  16. Report on achievements in fiscal 1999. System technology to create human life compatible living environment; 1999 nendo ningen kodo tekigogata seikatsu kankyo soshutsu system gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present research and development is intended to develop the following technology: a system technology to measure, understand and accumulate human activities, analyze objectively the compatibility of human being with products and environments, and support to have the products and working environments comply with activity characteristics of individual persons (a system technology to create human life compatible living environment). Human activities are developed in various scenes, and it is not easy to structure technologies to measure, understand and support the activities common to all of the scenes. Therefore, development will be made on the technologies for measuring, understanding and supporting the activities in the human activity scenes. Development of the manipulative activity complying technology deals with human activities in the scenes to operate devices by which the activities are changed by situation identification and skills in addition to activity characteristics of individual persons. Furthermore, as a scene in which attention to the activity characteristics of individual persons, skills, and external situation is a problem, the automobile driving activities are taken up for discussion, as well as the object building work activities as a scene in which difference in skills of individuals is a problem. (NEDO)

  17. Development of the molecule imprint polymer recognized peculiarly the environment hormone; Kankyo horumon wo tokuiteki ni ninshiki kanona bunshi inpurinto porima no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, M. [Kagoshima Univ., Kagoshima (Japan)

    2000-08-05

    The molecule imprint method (MI method) is the technique that makes the binding site which is complementary with the mold molecule in the polymer using a recognized object molecule as a mold, and gives the selectivity of the purpose in the polymer tailor-made like. The environment hormone is represented in the chemical substances (phthalic ester, bisphenol A, alkylphenol) which are produced from plastics or dioxins when refuse is burnt, and the organochlorine compounds (PCB, DDT, HCH) which are included in agricultural chemicals or chemicals besides. Whitcombe et al. report with respect to the MI polymer of which the recognition target is 2,3,7,8 tetrachlorodibenzodioxne (TCDD) which has the strongest toxicity in the dioxins. As an example of the MI method which targeted the other environment hormone, there is the research with respect to PCB by Hosoya et al. (NEDO)

  18. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by Optoelectronic Industry and Technology Development Association as part of the cooperation programs, for establishing the Asian environmental information networks. It outlines the research cooperation project for the environmental networks, results of the 4 on-the-spot surveys, 2 occasions for inviting researchers to Japan, and construction of the internet and Asian environmental information network systems. (NEDO)

  19. Research on improvement of indoor air quality and prevention of fungi; Shitsunai kuki kankyo no kaizen to kabi boshi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Tatsuaki [Ochanomizu University, Tokyo (Japan). Faculty of Human Life and Environmental Sciences

    1998-12-16

    An epidemiological survey survey was performed to elucidate the fungal flora of a dwelling house. The measurements were carried out in an apartment in Yokohama from Jul. 1996 to Dec. 1997. Fungi were isolated from 106 sampling points (the surface of the walls, floors, etc.) with sterile stamps. It was proved that Cladsporium, Penicillium, Eurotium, and Yeasts showed characteristic distribution. Especially Cladsporium was not isolated from the spring to the summer, but increased in the autumn. In addition to the survey, experiments on fungal growth temperature (13, 20, 25, 30, 36, 42 degree C) and water activity (A w 0.75{approx}0.97) were carried out. Cladsporium grew well in 13, 20, 25 and 30 degree C, but didn't grow in 36 and 42 degree C. In addition, the growth activity of Cladsporium was down below Aw 0.91. Eurotium was isolated from under Tatami, where it has an unchanging temperature and relative humidity. Yeasts preferred very high humidity. It was concluded that environmental factors such as temperature and relative humidity related to the growth of fungi. (author)

  20. Environmentally friendly type coal utilization technology transfer project. Downstream field; Kankyo chowagata sekitan riyo gijutsu iten jigyo. Karyu bun`ya

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper arranged the result of the clean coal technology transfer project carried out during October to December, 1996. For the purpose of supporting introduction/spread of clean coal technology (CCT) in Asian and Pacific countries, the project invited engineers of the countries to Japan, aiming at fermentation of the understanding of CCT and improvement in ability. The project was held by NEDO and managed by Center for Coal Utilization, Japan. The manager course is for policy decision makers, management and senior management (plant manager class). By taking up CCT assessment and a menu of economical efficiency, prepared was the environment to which CCT is introduced in case of working out policy and planning plant/equipment investment. Moreover, the engineer course is for policy planners, medium-class management (section chief class), senior engineers (planners), and takes up materials for judgment in case of planning CCT facilities and proposing measures to reduce environmental loads by management and improvement of facilities at the same time. Fifteen engineers were invited: 6 from China, 3 from Indonesia, 3 from the Philippines, and 3 from Thailand

  1. Research report of fiscal 1997. Survey on information networks for environment technology transfer; 1997 nendo hokokusho. Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    ICETT is one of the member organizations of APEC environment technology virtual center which established in Osaka in 1996 for active environment technology exchange between APEC countries based on a survey result obtained in fiscal 1995. ICETT began its information service in April, 1997, and completed useful prototype home pages which include the database composed of practical useful information on environment preservation technology of domestic factories and offices, and training information and local governments` approach cases to pollution control. In fiscal 1997, further survey was made, and the simulation software of a model process was also developed for training. Clean technology and energy saving technology strongly demanded by developing countries were surveyed to prepare a database including useful information for developing countries. A basic design software for bio-treatment of waste water was also prepared. The total number of home page accesses exceeded a predicted number for the first half year. 5 refs., 25 figs.

  2. FY1998 research report on the R and D on recycling technology. Part 1; 1998 nendo recycle nado kankyo gijutsu kekyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims to develop recycling technology for reduction of environmental burden caused by waste, and promotion of recycling of wastes. As for advanced recycling technology for PET bottles, the facility was improved for improvement of a facility operability and product quality. Study was made on the effect of a raw bale quality and recycled flake colors on a product quality, the forming test with PS or PET labels, and the concentration and effect of washing liquid circulated in flake washing process. As for recycling technology of hard-to-dispose waste plastics, facility improvement and demonstration test were made for continuous operation of dry-distillation/gasification of shredder dusts and separation of nonferrous metals and glass. Study was also made on pulverizing and recycling technologies of FRP bath tubs, and such pulverization costs were estimated. As for production technology of chemical feed and fuel from wastes, study was made on removal technology of non-flammable substances, development of alkaline additives, reacting condition, development of reactors, and use technology as chemical feed. (NEDO)

  3. Fiscal 1998 R and D report on environment-friendly hydrogen production technology; Kankyo chowagata suiso seizo gijutsu kenkyu kaihatsu 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For efficient oil-free environment-friendly production of hydrogen necessary for oil refining process and effective use of CO{sub 2}, this project develops the efficient hydrogen production techniques by using a capacity of microorganisms. On the R and D on improvement of screening and breeding for photosynthetic microorganisms, introduction of different hydrogenases, acquisition of hydrogen uptake negative strains, control of photosynthetic pigment expression, breeding of PHB synthesis negative strains were carried out continuously, and some problems were arranged confirming the contribution to increasing a hydrogen production capacity. On the R and D on large-scale cultivation techniques, engineering data were collected by using a module continuously. Based on the engineering data collected by the module test, the feasibility study was made on a possibility as industrial technology from the viewpoint of a profitability and environmental harmony. Screening of bacterial strains suitable for 4 kinds of wastewater and capable of producing hydrogen under extreme conditions, and basic studies on photoreactor and cultivation technique were conducted by outside research organizations. (NEDO)

  4. FY 1998 annual report on the fourth international forum on environmental catalysis (IFEC 99); Dai 4 kai kankyo shokubai kokusai forum (IFEC '99) 1998 nendo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The 4th international forum on environmental catalysis, held in January 1999 in Chemical Society of Japan's Hall, had a total attendees exceeding 170, including 10 foreign attendees invited. A total of 20 papers (including 10 by foreign attendees) were presented, discussing diversified problems; 3 keynote addresses regarding (to what extent environmental catalyst can contribute); and 5 for the session of catalysts for clean processes, 6 for the session of eco-friendly chemistry, and 8 for the session of environmental catalysts for air pollution. The lectures included (global environmental problems and environmental catalysts) by Prof. Segawa of Sophia University as the opening address; solid base catalysts by Prof. Ono of Tokyo Institute of Technology in the session of (catalysts for clean processes); activation of dioxygen by transition metal complexes-new approach to highly selective catalytic oxidation with molecular oxygen by Prof. Moro-oka of Tokyo Institute of Technology in the session of (Eco-friendly chemistry; and environmental catalysts-present and future as the comprehensive review by Prof. Misono of University of Tokyo in the session of (environmental catalysts for air pollution). (NEDO)

  5. Research report of fiscal 1997. Survey on strategies of export of environment technology in overseas countries; 1997 nendo chosa hokokusho. Shogaikoku no kankyo gijutsu yushutsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For active environment technology export to OECD countries, needs for environmental measures in developing countries were surveyed. Both collection of environment technology needs in developing countries and preparation of technology seeds information of Japanese enterprises, and promotion of environmental projects by adding an information dispatch function are important. Active preparation and exchange of experiences and know-how of concerned enterprises, local governments and national organizations are also necessary. For development and possible export of small- and medium-sized ventures with excellent technologies and know-how, a suitable consulting system is essential for risks. For smooth promotion of warming prevention by international cooperation, active development of monitoring technology is also important. To support developing countries, OJT of persons in charge in technology transfer sites, and preparation of information infrastructure are necessary. Japan with much know-how on environmental preservation should positively participate in international standardization activities such as ISO. 10 refs., 14 figs., 56 tabs.

  6. Report on an international joint research project for global environment technology in fiscal 1998; 1998 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to serve for measures against global problems taken by Japan, joint research was carried out with overseas research organizations. The research project selected ten themes considering urgency, internationality and economic proliferation effect in areas to serve for solution of global environment problems. These themes include removal or emission control of greenhouse effect gases, measures against atmospheric environment problems such as acid rains and ozone layer destruction, prevention of ocean contamination, development and effective utilization of energies and resources. When the feedback of these themes to the NEDO projects is considered, the research achievements in relation with development of the acid rain monitoring system in particular support indirectly development of carbon dioxide fixation technologies. The research achievements in developing an environmentally friendly biomass energy manufacturing process and environmental effect evaluation thereon contribute as an effective process to carbon dioxide reduction using biomass as raw materials. The achievements in research of nonlinear interfacial properties and mixed phase turbulence of low-purity carbon dioxide bubbles contribute to a project related to storage of carbon dioxide in oceans. (NEDO)

  7. Fiscal 1998 survey report. Survey on method of environmental-impact assessment in wind power development; 1998 nendo furyoku kaihatsu ni okeru kankyo eikyo hyoka shuho chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With the purpose of preparing the main points of 'environmental-impact assessment guidelines for wind power developments (draft)', examples of environmental-impact assessments, related laws and regulations in Japan and abroad were collected, and rearranged in respect to requirements in environmental-assessments, concrete procedures, survey/projection/assessment method, summarisation of results, etc. It was clarified, for example; in a large-scale wind power development, it can be dealt with by choosing items and contents on the assumption that a land area is developed; in a small-scale development, there is basically no need of considering the possible effect of the construction work; and, as far as noise, vibration and the ecosystem (plants/animals) are concerned, however, the characteristics of the site be taken into consideration. Objects for general assessment are noise, low-frequency air vibration, radio wave interference, the ecosystem (plants and animals) and the landscape. The guideline draft is constituted of (1) basic items, (2) overview of the area, (3) determination of items for environmental-impact assessment and (4) research, prediction, assessment, conservation measures and follow-up research; in the basic items, importance of preliminary consideration was emphasized, as were priority/simplification, implementation of environmental conservation measures, and implementation of follow-up research. (NEDO)

  8. Global environment assessment survey by advancing the energy demand and supply structure. 4; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To investigate the energy demand and supply structure in Japan, the international trend of approaches to global warming problems and the mitigation options to global warming in the energy related sectors have been surveyed. For the United Nations Framework Convention on Climate Change, an Ad-hoc Group has discussed relevant topics after the 1st conference of the Parties. Meetings of the Group primarily focused on what objectives to set for the reduction of greenhouse gas (GHG) emissions in and in and after 2000. IPCC completed their Technical Paper in November 1996 in which technologies and measures to reduce GHG emissions and to enhance GHG sinks were analyzed and evaluated in various aspects. This Paper discusses about each sector of institutional buildings sector, transport sector, industrial sector, and energy supply sector. Especially, in the energy supply sector, promising approaches to reduce future emission include more efficient conversion of fossil fuels, switching to low-carbon fossil fuels, decarbonization of flue gas and fuels, CO2 storage, switching to nuclear energy, and switching to renewable sources of energy. 5 refs., 2 figs., 14 tabs.

  9. Research and development cooperation project on environmental measurement using laser radar in fiscal 1995; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of contributing to the environmental management in Indonesia, Japan made R and D of a laser radar to measure the urban air pollution and an environmental network jointly with Indonesia in compliance with the actual situation of the country. At present, in developing countries, air pollution is becoming a big problem because of increases in population and in energy consumption in urban areas according to the industrial/economic growth. As for the laser radar, it is an active sensor with laser as light source and can observe in high resolution the three-dimensional space distribution such as density and composition of air pollutants. Japan is a leader in the development of laser technology which is a core technology for the laser radar and the preceding research. The equipment is installed at several points of urban areas in Indonesia, and at the same time, the observation network is constructed to collect, analyze and process data at the central processing center. This is a 4-year plan from fiscal 1993 to 1996. In fiscal 1995, negotiations with Indonesia and field surveys were conducted to determine sites for installation. A plan for system improvement was also decided on. 38 refs., 24 figs., 14 tabs.

  10. Research cooperation of the development of laser radar for environmental measurements; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research and development of the laser radar for measuring the air pollution in urban areas and the environmental information network have been conducted through the cooperation with Indonesian researchers. A measurement system suitable to actual situation of Indonesia has been constructed. In FY 1996, some works have been conducted as in the final fiscal year. To set the laser radar for environmental measurements and to make a plan of measurement research, conditions of air pollution in Indonesia and setting places of systems have been investigated. Opinions for the cooperation research have been exchanged with Indonesian researchers. Actual trends of the environmental measurements technology using laser radar have been surveyed. Indonesian researchers have been invited to learn operation and data processing of the system. One unit of MIE diffusion laser radar system has been designed and fabricated, and an additional data processing program has been made. The system has been delivered to Jakarta and installed. After the adjustment, performance tests have been conducted to complete the construction of the system. 3 refs., 72 figs., 10 tabs.

  11. Chemistry for preserving the global environment. Part 5. Offensive odor; its present condition and control technique; Kankyo sozai no kagaku. 5. Akushu no genjo to taisaku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Saiki, Y.

    1996-07-01

    Offensive odor substances belongs to a quite different field from the perfume inspire of the same sense of smell, and is a substance forming a lot of troubles which is formed in intimate resident environments such as manufacturing factories of the chemicals, incineration and decomposition treatment process of living body relating substances, stock raising facilities, restaurants and others. A material called the offensive odor substance is generally in very low concentration in the atmosphere, most of which is ppm order in its detection limit. And, the offensive odor intensity is proportional to logarithm of its concentration. For example, even removing 99.9% of the offensive odor substance from its forming source, there is remained its difficult countermeasuring problem of no removing as its offensive odor. At present, the offensive odor is severely regulated by means of laws and acts, research on its relating field is active, and its relating publications have become plenty. In this paper, outline on recent state of the offensive odor and its measuring technique was summarized. 14 refs., 6 figs., 8 tabs.

  12. Response to resolve environmental problems caused from power stations. Reuse engineering of waste water; Hatsudensho kankyo mondai kaiketsu e mukete no torikumi. Haisui no sairiyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Hayashida, T. [Hitachi Plant Engineering and Construction Co. Ltd., Tokyo (Japan); Hatta, T. [Kurita Water Industries Ltd., Tokyo (Japan)

    1997-10-15

    This paper introduces the electrodialysis method, the reverse osmosis method, and the evaporation system for reutilization of waste water in non-collection lines in power plants. In the electrodialysis method, waste water which has been divided and fed conventionally into a desalination chamber and a concentration chamber is supplied into the desalination chamber in the whole quantity to improve the recovery efficiency. A process of supplying sea water into the concentration chamber has made prevention of scaling possible. A small testing machine of high recovery electrodialysis system utilizing sea water was installed in an exclusively coal burning thermal power plant. A 3200-hour verification test has been performed, and its high treatment performance was verified. General waste water in thermal power plants is a waste water relatively less contaminated, which can be desalinated by using the reverse osmosis method to recover usable water at a low cost. However, the recovery rate decreases if salt concentration in the waste water is high. In contrast, the evaporation method can maintain the recovery rate at 90% or higher for salt concentration in the subject waste water of up to 20 g/l. Power plants in the United States built in inland areas use the evaporation method because of difficulty in obtaining sufficient amount of water. 6 refs., 22 figs., 7 tabs.

  13. Feasibility design of a floating airport and estimation of environmental forces on it; Futaishiki kuko no sekkei to kankyo gairyoku no suitei ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, Y.; Tabeta, S.; Takei, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1996-12-31

    A rough design was performed on a floating airport. On this floating structure, environmental external force was estimated, mooring design was carried out, and discussions was given on the position retaining performance important for airport functions and behavior of the floating structure. The discussion was given on cases that the airport is surrounded and not surrounded by floating breakwaters. A floating structure which becomes super-large in size requires considerations on force due to sea level gradient as a result of a tide. Deriving flow condition changes and force acting on the floating structure simultaneously by using numerical calculations makes it possible to estimate current force given with considerations on influence of the flow conditions created by installing the floating airport. Estimation was carried out by using a zone dividing method on wave drifting force acting upon the floating airport. As a result, it was found that installing floating and permeating type breakwaters can reduce the wave drifting force acting on the floating airport. The wave drifting force working on the floating airport can be reduced by installing the floating and permeating type breakwaters to lower levels than when no such breakwaters are installed. The airport may be moored with less number of fenders when the fenders of the same type are used. 18 refs., 10 figs., 5 tabs.

  14. Evaluation of building envelopes from the viewpoint of capability of controlling thermal environment; Onnetsu kankyo chosei noryoku ni yoru kenchiku gaihi no hyoka no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Umeda, K; Ono, S [Taisei Corp., Tokyo (Japan); Shukuya, M [Musashi Institute of Technology, Tokyo (Japan)

    1996-10-27

    The ability that architectural space improves the thermal environment in comparison with outdoor environment is called the `capability of controlling thermal environment.` As the value becomes higher, the indoor thermal environment is more improved. In this paper, the controlling capability of six building envelopes with different window systems was compared. The heat transfer in the wall and window system is approximated using a lumped mass model of heat capacity to obtain a heat balance equation and combined with the heat balance equation in indoor air for backward difference. The wall surface temperature and indoor air temperature in a calculation model are then calculated. A radiation absorption coefficient is used for mutual radiation on each wall. In the model, the adjoining room or first- and second-floor rooms were made the same in conditions as the model on the assumption that the one-side lighted office in an RC reference floor is in the non-illumination and non-airconditioning state. In summer, the controlling capability remarkably varies depending on the window system. For the window facing the south, the annual capability is more advanced than in other directions and the indoor thermal environment is improved on the average. 7 refs., 12 figs., 1 tab.

  15. Realization of an accelerator for environmental refreshment in case of soil; Dojo no kankyo sosei no tame no kasoku no jitsugen

    Energy Technology Data Exchange (ETDEWEB)

    Isogai, H; Kawakami, T [Electrotechnical Laboratories, Tsukuba (Japan)

    1996-10-27

    Techniques have been studied to accelerate, on a commercial scale, the natural refreshment effects which synthesize useful materials, such as compost and grape and amino acids from carbon dioxide, oxidized wastes and excretions exhausted by man. The symbiotic relationship between primeval bacteria and useful bacteria for Japanese traditional foods was investigated in 3 different experimental sections which were commonly composted; the first one consisting of composted soil, the second one provided with a layer (EM layer), in which these bacteria were densely cultured, on composted soil, and the third one with a common accelerator driven only by solar energy. A total of 9 seed potatoes were planted, 3 for each section, to monitor their growth. It is quantitatively confirmed that, when cultured in the third section, they grow roughly 3 times faster than in the first one. Sweetness can be sufficiently secured by the EM effect, because of sufficiently high ground temperature in early summer and an anaerobic atmosphere kept in the system. 6 refs., 2 figs.

  16. Global environment action plant of Japan Society of Civil Engineers. ; Agenda 21 / Japan Society of Civil Engineers. Doboku gakkai chikyu kankyo kodo keikaku. ; Agenda 21 / doboku gakkai

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-15

    This paper explains the involvement of the global environment action plan of Japan Society of Civil Engineers, Agenda 21, with civil engineerings and global environmental problems, as well as the global environment action plan. Global environmental problems require handling the matters in three ways: identification and elucidation of events, effect analysis estimation, and alleviation, avoidance and prevention of the effect. Settlement and proliferation of civil engineering technologies transferred to developing countries demand indispensably understanding such features of the developing countries as social and economic conditions, natural conditions, climates, histories, races, and cultures. Realizing the sustainable development requires the followings: formation of civil engineerings that contribute to improving global environments; development of civil engineerings that make coexistence of human being and other living organisms possible; analyses of effects and mechanisms of global warming and weather change and the corresponding technique and system development; and development of techniques to build resource circulating type national land and cities. It is also essential to move forward positively structuring civil engineerings that contribute to solving such global environmental problems as acid rains and marine pollution, and technical development thereof; providing guidelines on execution of international civil engineering constructions, and technical development thereof; developing civil engineerings in developing countries and assisting training of people.

  17. Fiscal 1999 research report. Survey on geothermal development sites (Survey on natural environment); 1999 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the result on selecting sites for large-caliber production wells, and landscape characteristic evaluation for simulation, based on the landscape survey on C candidate site for geothermal development. Field survey was made on landscape, plants and animals in the Kirishima Eboshidake area. It was clarified that this area has diverse flora including some rare species such as rein orchid and monkshood which are listed as endangered species. In addition, not a few epiphytes were identified. The zoological survey result showed that planted forests of evergreen coniferous trees which cover a wide range of the surveyed area, and peripheral grassland, scrub and natural forests provide good habitats for mammals such as sika deer and wild boars. On the other hand, no animal species in need of special protection were found. Geologically some traces of landslide occurrence in the past were detected in the northern part of the surveyed area relatively. As the survey result, some promising sites suitable for geothermal development were selected, which are judged to have a relatively small impact on natural environment and landscape. (NEDO)

  18. Fiscal 1994 survey report. Survey of environmentally friendly chemical process (Ecochemistry); 1994 nendo kankyo ni yasashii kagaku hanno process (ecochemistry) ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Processes that contain latent environmental problems are the massive generation of wastes (inorganic salt, acid catalyst, base catalyst, and huge quantities of wastewater), handling of dangerous substances (use of hydrogen fluoride, use of phosgene, and use of substances whose discharge is legally controlled), processes which consume much energy (circulation of quantities of raw materials, use of quantities of solvents, separation of products with difficulties, use of high pressure, and multiple stage reaction), and processes which are expected to use resources now remaining unexploited. As an element technology for the solution of problems, there is the development of a solid redox catalyst for liquid phase oxidation. As compared with a liquid phase homogeneous catalyst, it discharges less inorganic wastes, facilitates the separation, recovery, and treatment of inorganic salts, corrodes structural materials less, and is thermally stable. An alkane partial oxidation catalyst when developed will achieve more energy conservation than an alkene oxidation catalyst. In relation to acid/base reaction, the zeolite catalyst will be improved and ultrastrong acids and ultrastrong bases will be developed, and these will reduce wastes, mitigate corrosion, and facilitate product separation. The development of a process is also expected which will avoid the use of toxic phosgene. (NEDO)

  19. Fiscal 1998 research report on the global environmental assessment for efficient energy consumption; 1998 nendo energy shohi koritsuka chikyu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    International Panel on Climate Change (IPCC) published the 1st assessment report in 1990 and the 2nd report in 1995 since its establishment in 1988, and is promoting the 3rd research and analysis. Among them, this report describes the study on technology transfer for efficient energy consumption. For stabilizing greenhouse effect gas concentrations in the air, strong control of such gas emission is indispensable, and a role of technology is important for the control. For overcoming some weak points for climate change, practical use of applicable technologies is necessary over a certain period of time, and technology transfer is essential in each country and all over the world. For promotion of such approach, the analysis and evaluation for technology transfer and diffusion are useful in addition to reports on technology itself. Based on such understanding, IPCC has promoted preparation of the special report on methodological and technological issues of technology transfer since 1997. Its approval at the IPCC general meeting is expected in late 1999 or early 2000. Some chapters related to efficient energy consumption are presented. (NEDO)

  20. Current status and prospect on photo-catalyst application in environmental problems; Kankyo mondai ni okeru hikari shokubai oyo no ganjo to tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Toto Ltd., Kitakyushu (Japan)

    1995-09-30

    This paper summarizes application of photo-catalysts in environmental problems. The paper lists examples of the application in residential environments. Photo-catalytic decomposition is possible by using ultraviolet rays contained in room illumination if the bacterial presence is sparse. The examples thereof may be cited as follows: if colon bacilli are suspended on a tile with TiO2 photo-catalyst sintered in it and exposed to room illumination, the bacteria are disinfected; using photo-catalysts in a bathroom suppresses deposition of Pseudomonas aeruginosa; a photo-catalyst tile (TiO2 loaded with Cu) and light irradiation reduce intensity of tobacco smoke odor; and adsorbents may be used simultaneously if intermediate products are odor generating substances. The examples of applying photo-catalysts to regional environments may be quoted as follows: growth of algae in a Petri dish is suppressed by presence of Cu loaded TiO2 under room illumination; this leads to an expectation on its effect in a relatively clean water environment; glass beads loaded with a TiO2 photo-catalyst placed in a gold fish breeding tank reduces turbidity, the number of colon bacilluses, and COD value; and the mortality in gold fish shows no change. With an objective of application to exterior building materials, photo-catalyst applied tiles were left outdoors for 160 days. Nitric acid ions were detected that are thought to have been generated by decomposition of microorganisms that have deposited on the tiles. 6 refs., 5 figs., 3 tabs.

  1. Effect of Water Environment on Subcritical Crack Growth of Machinable Ceramics; Kaisakusei seramikkusu no kiretsu shinten tokusei ni oyobosu mizu kankyo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Kaizu, K.; Inotani, T. [Miyazaki Univ., Miyazaki (Japan); Yoshikawa, A.; Adachi, K.; Igaki, H. [Osaka Sangyo Univ., Osaka (Japan)

    1997-06-15

    The fatigue behavior of ceramics has been discussed on the basis of the relation between stress intensity facter (KI) and crack velocity (V). In this paper, the effect of environment on the relation between KI and V was studied on machinable ceramics (mica glass ceramics) and two kinds of glass ceramics with different grain sizes. The double torsion (DT) technique was used for the determination of the KI-V characteristics under different environments of air and ion-exchanged water. The characteristics of acoustic emission (AE) during stress corrosion cracking of mica glass ceramics was also examined. In water environment, the region II in the KI-V curve, in which crack velocity varies slowly with KI, disappeared. From this experimental fact, it was considered that at high KI, the crack velocity is encouraged by diffusion of the corrosive species to the crack and thus depended on the amount of water. SEM farc tography revealed that mica single crystals in the material caused crack arrest and deflection to occur. It is also found that AE event rate is quantitatively related to the crack velocity. AE measurement can be used in studying the crack propagation behavior of mica glass ceramics. 11 refs., 12 figs., 3 tabs.

  2. Energy, oil and global environmental problems towards21st. century. 21 seiki ni mukatte no energyter dot sekiyuter dot chikyu kankyo mondai

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, K [Mitsubishi Oil Co. Ltd., Tokyo (Japan)

    1990-09-01

    The world energy demand is increasing with the development of the world economy and the improvement of the life level. In view of the future economic development and population growth, the world energy demand will considerably increase especially in the LDCs. Since the oil crisis, saving of energy and material were effectively executed, thus significantly reducing the energy requirement per GNP. However, in the recent several years, the conciousness of energy has become diluted, causing considerable consumption in larger size and higher grade products, thus increasing the non-industrial and transportation consumption. This report considered the effective use of energy and the nuclear application. It is to be noted that the accident frequency in the Japanese nuclear plants is much less than the other countries. The coal utilization requires further technical development in view of the environmental problems. Other substitutible energies are all weak in competition and cannot be expected utilizable in large scale for the time being. This report also referred to the oil problem. 9 figs.

  3. Project to promote the development of global environmental industry technology. Feasibility study of research exchanges; Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kenkyu koryu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In fiscal 1995, three teams were organized to study the following subjects: plant genetic and cellular engineering in relation to drought stress; simulation models of global environment for accurate assessment and prediction; the APEC Virtual Center for environmental technology exchange. The team studying plant genetic and cellular engineering in relation to drought stress visited the Department of Botany, Hebrew University of Jerusalem, Israel, the Jacob Blaustein Institute for Desert Research, Ben-Grunion University, Israel, the Department of Biochemistry and the Office of Arid Lands Studies, Arizona University, the U.S. to survey the present and future trend of the study and feasibility of research exchanges. The team studying simulation models of global environment for accurate assessment and prediction visited Yale University, Massachusetts Institute of Technology, Electric Power Research Institute, and Battle Research Institute in the U.S. to survey feasibility of research exchanges. The team studying the APEC Virtual Center for environmental technology exchange visited institutes in ASEAN countries to survey needs for the Virtual Center. 312 refs., 74 figs., 17 tabs.

  4. FY1995 study on three-dimensional integrated information environment toward human media; 1995 nendo human media e muketa sanjigen togo joho kankyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the next generation media environment, it is required to remove the boundary between virtual and real environment. The integration of these heterogeneous environments will enhance the applicability and availability of the human media. The aim of this work is to pioneer the new technology of 3-D integrated information environment in which both virtual and real environment are embedded, and to give a guide into the construction of human media. Our results consists of three parts as follows : (1) As a benchmark of the 3-D integrated information environment, the immersive television which has surrounding multi-projection displays was investigated. (2) A new method to synthesize arbitrary 3-D viewpoint images from 2-D real images was developed. On the other hand, a new concept of ray data description was introduced to represent whole visual data of 3-D real space. In the new concept, the whole visual data is treated as a set of ray data. New methods for superimposing and handling ray data were proposed. Potential applicability of the methods were clarified. (3) In order to enhance the reality of operations under the virtual environment, quantitative analysis was performed assuming that the HMD (Head Mounted Display) was used for displaying 3-D space information. (NEDO)

  5. Survey of effects of enhancement of the energy supply/demand structure on the global environment. 3; Energy jukyu kozo kodoka chikyu kankyo eikyo chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of studying how the energy supply/demand structure in Japan should be, a report on the secondary IPCC (Intergovernmental Panel on Climate Change) evaluation was analyzed. Possibilities of reducing the world CO2 emissions in association with the energy consumption were studied in the five assumed cases. Every case says that CO2 can be reduced to 1/3 of the 1990 level by 2100. In a case of the use of biomass as main fuel (1), the use of primary energy is suppressed to two times the 1990 level, and photovoltaic/wind/biomass power generation is introduced in a large quantity. Synthetic methanol and hydrogen are used for transportation and commercial/residential use fuels. There are four more assumed cases: the use of nuclear power as a substitute for renewable energy in the power generation in (1), the use of natural gas of 1.5 times that used in (1), the substitution of coal for biomass used in (1), and the assumption that the demand for primary energy in 2100 will be twice that used in (1). In Japan it is assumed that basically the nuclear power generation will be expanded, that the photovoltaic and waste power generation will be introduced in a large quantity, and that synthetic methanol and hydrogen are mainly used as transportation and commercial/residential use fuels. It is necessary, therefore, to analyze conditions under which the quantity introduction of such non-fossil energy is made possible. 11 figs., 31 tabs.

  6. Fire safety and environmental design of deep underground spaces used for human activities. Daishindo chika kukan no bosai/kankyo sekkei

    Energy Technology Data Exchange (ETDEWEB)

    Saeki, N.; Kadoya, M.; Tokuda, K.; Hisajima, T.; Okada, N. (Okumura Corp., Osaka (Japan))

    1992-11-10

    The disaster prevention and environment technology, which is the essential conditions for the living in the underground space, was developed to be applied to a simulated model space. The basic conditions including the location and utilization for the simulation model are as follows: (1) It locates at the city center of a big city, (2) A station for a high speed rail way (linear car) is located at the deep underground (50 m), (3) As there are still many physiological and psychological problems left unsolved for the living including dinning and sleeping in the underground, such facilities as private residential house, hotel, and hospital were excluded. Such facilities as shop, restaurant, theater, recreation facility, city hall, police station, and parking lot were considered. For the disaster prevention design, the design technique for emergency evacuation system within the building and for the smoke control system were taken up. For the air conditioning design, the large space air conditioning design, energy saving design system, and the deodorant air conditioning system were investigated. The energy program and the aqueduct program were also discussed. 24 figs., 6 tabs.

  7. Evaluation of indoor thermal environment with improved 65 nodes thermoreguration model; Kairyogata 65 bunkatsu taion chosetsu model wo mochiita shashitsunai onnetsu kankyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, K; Sudo, F [Isuzu Motors Ltd., Tokyo (Japan); Tanabe, S [Ochanomizu Univ., Tokyo (Japan)

    1997-10-01

    Indoor thermal environment of a vehicle was evaluated by a numerical simulation. A numerical simulation using the equivalent temperature measured with the thermal manikin was conducted. Numerical manikin was improved and convective and radiative heat transfer at each body surface was described in detail. Comparative examination using the calculation results by the numerical simulation was also conducted. 3 refs., 8 figs., 2 tabs.

  8. Psychological influences for the driver by the changes of running circumstance; Jidosha no soko kankyo henka no driver eno shinriteki eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Okura, S; Yokomori, M; Yamaguchi, S [Meijo University, Nagoya (Japan)

    1997-10-01

    A driver is influenced psychologically by the cars proceeding on the street and the cars parked on the shoulder which come into the front view. The traffic accidents are caused when these influences put a lot of stress on a driver. In this report, we study the relations between the road traffic condition on the streets and the highway and the driver`s psychological and psysiological responses by using the driver`s front view, sweating and pulse rate. 6 refs., 8 figs.

  9. Report on the survey in fiscal 1998. Survey on an environment technology transfer information network; 1998 nendo hokokusho. Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes a survey on an environment technology transfer information network. Based on the achievements obtained by the surveys in fiscal 1995 and 1996, the ICETT has participated as one organization constituting the APEC environment technology exchange virtual center, and begun providing information since April 1997. As the environment technology information, those items actually employed by factories and operation sites in Japan are put into a data base, and into a home page including training information centering around those contained in the data base, and examples of works done by local governments for prevention of pollution. Furthermore in fiscal 1997, a simulation software for a model process has been developed. Fiscal 1998 strengthened the data base for environment preservation technology information, investigated environment preserving model companies and summarized them including even their management aspect. Investigations were carried out in developing countries on application of cleaner technologies. Gaps far exceeding anticipation exist in every field between these developing countries and Japan. Environment protection measures applied and succeeded in the developing countries as the means to narrow the gaps were collected, and compiled as the specific examples. (NEDO)

  10. Promotion project to develop the global environment related industrial technology. Investigation on the possibility of research exchange; Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kenkyu koryu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Through visits to US universities and research institutes, investigation was made on the trend of global environment-related research and possibility of their exchanging the result of research with the RITE (Research Institute of Innovative Technology for the Earth). To investigate the process technology to utilize microbes harmoniously with the environment, the visit was paid to Cornell University, Battelle Memorial Institute and Risk Reduction Engineering Laboratory, where the investigation was made on the environmental bioremediation with microbial functions and clean process production without by-producing substances to load the environment. To investigate the technical measures against the global warming, the visit was paid to Brookhaven National Laboratory, Massachusetts Institute of Technology, California University, Hawaii University and Pacific International Center for High Technology Research, where the investigation was made, through discussion and exchange of research information and opinion with researchers and engineers, on the possibility of their exchanging the result of research with the RITE. Judging from the investigation of this time, the research which is mutually complementary between Japan and USA is easy to promote, because their respective advanced fields do not overlap with each other. 88 refs., 11 figs., 6 tabs.

  11. FY 1998 annual report on the geothermal development promotion survey. Report on landscape survey; 1998 nendo chinetsu kaihatsu sokushin chosa hokokusho. Shizen kankyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are results of the natural environment surveys, carried out in the Shitanotai Region in Yuzawa City, Akita Pref., where Geothermal Development Promotion Survey C is scheduled. On-the-spot surveys, conducted from June to November, covered 3 items of landscape, vegetation and animals. The Shimonotai Region has a number of ponds and swamps, some of which are used as fields for Brasenia shreberi, and wet shield plant communities in places reflecting these environments. The zoological survey results show that moderate to dry deciduous forests of Japanese beeches (Fagus crenata) and Mongolian oaks (Quercus mongolica var. grossesserrata) in this region provide sound habitats for large mammalian wild animals, e.g., moon bears (Selenarctos thibetanus). For birds, there are some areas extracted indicating high possibility of being inhabited by honey buzzards (Pernis ptilorhyncus), which are listed as a near threatened species by the Environment Agency. Geologically, traces of landslide occurrence in the past have been detected widely, indicating need for more detailed investigation for land stability. These surveys have extracted several areas whose natural environments and landscapes are damaged relatively little by geothermal development. (NEDO)

  12. FY 1998 annual report on the environmental technology working group. 19th R and D activity report; 1998 nendo kankyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 activities by the environmental technology working group, extracted from the 19th R and D activity report by NEDO. Mr. Mitsukawa, a NEDO's director, outlines the measures for diversifying environmental problems, prevention of global warming, waste disposal/recycling, and toxic chemical substances in the report entitled (Outlines of environmental technology development projects). The report entitled (Eco-cement production techniques for comprehensive utilization of urban type wastes (For efforts for construction of Ichihara eco-cement production facilities)) outlines characteristics of eco-cement production techniques, recyclability of eco-cement, and the facilities. The report entitled (Techniques for reutilization of plastics present in wastes as the blast furnace stocks) outlines the system, R and D project and commercialization, and vinyl chloride recycling system, to be developed by the financial support by NEDO. The other reports include (Development of universal controllers for coping with environmental problems) and (R and D of techniques of simplified dioxine analysis). (NEDO)

  13. Assistance to countries which are on their way to energy conservation and preservation of the environment. Sho ene tojokoku enjo to kankyo hozen

    Energy Technology Data Exchange (ETDEWEB)

    Osaka, Kunikazu [The Energy Conservation Center, Tokyo, (Japan)

    1990-02-20

    Energy conservation is considered the most realistic measure against the problem of the global warming for the time being. Developing countries consume about 30% of the energy consumed in the world. Although their absolute consumption amount is little at the moment, their energy consumption is increasing year after year. Efficiency of their energy utilization is low because compared with advanced countries their equipments are of old type and their technologies are behind the times. It is, therefore, estimated possible to conserve energy by 30% with e improvements and plant and equipment investments. It is very effective to introduce Japanese advanced energy conservation technologies to these countries through international cooperation. In fact investigation commissions composed of experts have been dispatched to Thailand, China and Argentine, experts have been dispatched to foreign countries to stay there for several years and give assistance, trainees have been received, and study and training meetings have been held already. Seminars with Japanese lecturers have been also held in many foreign countries since 1983. As for the future prospect, establishment of core organizations as the base of technologies and human resources in foreign countries for the further promotion of assistance is expected. 7 figs.

  14. Report on a survey in fiscal 1999. Survey on possibilities of environmental cooperation in relation with proliferation of environment preservation technologies and institutions in developing countries; 1999 nendo kankyo taisaku gijutsu seido nado no tojokoku fukyu ni kakawaru kankyo kyoryoku kanoseichosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Cooperation in energy and environment aspects with developing countries is considered very important in view of the following points: (1) the cooperation will help developing countries to grow economically while minimizing the damages from industrial pollution and environmental problems; (2) conservation of energies and promotion of use of new energies will contribute to solving pollution problems associated with energy production, and will result in assurance of stability of primary energy availability for Japan; (3) preservation of environments in countries exporting foods to Japan will link to maintaining health of Japanese people and increasing their welfare; and (4) Japanese industrial pollution preventing technologies and knowledge whose levels are high worldwide may be utilized to create new business chances for Japanese business entities. The present survey has discussed the importance by territories, the importance by cooperation modes, and sharing of roles by governmental and private organizations, and performed case studies. Considerations were given from the discussion results on how the environmental projects should be planned in the environment cooperation, the contents to be of win/win from the viewpoint of motivation, the project image for subjected territories being composite and comprehensive, and the cases from the viewpoint of mutual coexistence referred to as prevention of global warming and assurance of food and energy resources. (NEDO)

  15. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

  16. Achievement report (2/2) on R and D in fiscal 1999 on environment adaptive next-generation supersonic propulsion system. R and D of environment adaptive next-generation supersonic propulsion engine; 1999 nendo seika hokokusho. Kankyo tekigo gata jisedai choonsoku suishin system no kenkyu kaihatsu - Kankyo tekigo gata jisedai choonsokuki you enjin kaihatsu (2/2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    With an objective to develop an environment adaptive next-generation supersonic propulsion system, research and development have been performed on noise reducing technologies, NOx exhaust reducing technologies, CO2 exhaust reducing technologies, and environment adaptive engine system technologies. This paper summarizes the achievements in fiscal 1999. In developing the CO2 exhaust reducing technologies, discussions were given on the following items as the researches on a technology to apply three-dimensional fiber-reinforced materials to large structures: application of metal-based composite materials (MMC) to the fan rotor; application of CMC, TiAl materials to turbine structural materials; TiAl shroud support, CMC shroud, high load turbine cascades supported by the composite materials, and application of the CMC, TiAl materials to the gas exhaust nozzle. In developing the environment adaptive engine system technologies, flows were established to judge the achievement of the project target of noise reduction, NOx exhaust reduction and CO2 exhaust suppression. Furthermore, in the demonstration and research of the engine integration, the setting was conducted on the engine test schedule, and so was the primary setting for criteria on parts to be assembled into the engine. (NEDO)

  17. Fiscal 2000 survey report on Asia/Pacific Regional Environment Problems Researcher Exchange Promotion Projects. Construction of Environmental Technology Research Network in the Asia/Pacific Region; 2000 nendo Asia Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho. Asia/Taiheiyo chiiki kankyo gijutsu kenkyu kaihatsu network kochiku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of developing and popularizing environment conservation technologies in the Asia/Pacific region, activities were conducted for Environmental Technology Research Network in the Asia/Pacific Area (ETERNET-APR). In this fiscal year, under the motto of Expansion of International Collaborative Researches on Environmental Technology, a 7th international workshop was held in Yokkaichi City, Mie Prefecture, with the attendance of approximately 60 people in Japan and from abroad. Researchers from overseas, in addition, attended a 10-day training program at the National Institute for Resources and Development and others in preparation for the embodiment of international collaborative research. A survey was conducted overseas for the promotion of database utilization and registration and for grasping the problems intrinsic to the respective research institutes and problems to occur at every stage of development. People's Republic of China was visited, where a miniscale workshop was held, study tours were made, and opinions were exchanged. It was actually felt, at the places that were visited, that ETERNET-APR was certainly in function in various fields. (NEDO)

  18. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Malaysia and Vietnam; Kankyo chowagata sekitan riyo system kanosei chosa. Malaysia Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This survey arranged the status of coal utilization technology and the status of coal production, supply, etc. in Malaysia and Vietnam, examined/studied coal utilization systems in both countries, and finally assessed feasibility of introducing the environmentally friendly type coal utilization system. As a country of primary energy source which is abundant in crude oil, natural gas, hydroelectric power, coal, etc., Malaysia now depends on crude oil and natural gas for 80% of its energy, and places emphasis on exploration of natural gas and oil refining. In electric power and cement industries where coal is consumed, effectiveness and environmental issues in association with coal utilization are future subjects. In Vietnam, the north is abundant in hydroelectric power and anthracite, and the south in oil and gas resource, but the north and central districts are in a state of undevelopment. Coal is used for coal thermal power generation, cement industry, and residential/commercial fuel. In the future, effective coal utilization and environmental issues will be subjects. 16 refs., 38 figs., 75 tabs.

  19. Change of environmental factors in different site which effect the conversion efficiency of photovoltaic module. Comparison of the environmental factors in Shinjuku Tokyo with the one in Chino Nagano; Kotonaru chiten ni okeru taiyo denchi no henkan koritsu ni eikyo wo ataeru kankyo inshi no henka. Tokyoto Shinjukuku to Naganoken Chinoshi no kankyo inshi no hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, T.; Tani, T.; Hirata, Y.; Inasaka, T. [Science University of Tokyo, Tokyo (Japan)

    1997-11-25

    Environmental factors affecting conversion efficiency of solar cells were measured in Tokyo and Nagano to comparatively study the difference. In the study, measurement was made of intensity of global solar radiation on an inclined surface (insolation intensity), ambient air temperature, and distribution of spectral solar radiation at the two points. Also measured were output characteristics of polycrystal silicon solar cell modules and amorphous silicon solar cell modules. The result of the comparative analysis was as follows: The annual inclined global solar radiation amount integrated in 1996 is 27% more in Nagano than in Tokyo. The weighted average insolation intensity in Nagano is 0.09 kW/m{sup 2} higher in Tokyo. The weighted average cell temperature in Nagano is 4degC lower than in Tokyo. The effective spectral ratio in Nagano is 1-2% lower both in polycrystal Si and amorphous Si than in Tokyo. Thus, it was inferred from that environmental factors are different that conversion efficiencies of photovoltaic modules were different. 6 refs., 5 figs., 5 tabs.

  20. Achievement report for fiscal 2000 on research and development of environment compatible next generation supersonic propulsion system. 2/2. Development of environment compatible next generation supersonic aircraft engine; 2000 nendo kankyo tekigogata jisedai choonsoku suishin system no kenkyu kaihatsu seika hokokusho. 2/2. Kankyo tekigogata jisedai choonsokukiyo engine kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 in development of an environment compatible next generation supersonic aircraft engine. Development is performed, as part of CO2 emission suppressing technology development, on technologies for application to fan and compressor of metal matrix composites (MMC) having high specific strength useful to reduce engine weight, and brisk structures. Discussions were given on the spraying method for ring manufacturing, mono-tape method, and preliminary test method for fan aerodynamic performance verification. In order to reduce engine weight and fuel consumption, enhancement is required on the turbine inlet temperature and engine efficiency, whereas studies were made on mono-crystalline heat resistant alloy TMS-75 developed in Japan for application to the turbine structure. Studies were continued on castability, heat-treated structure control, mechanical properties, heat resistance and heat oxidation resistance. For the purpose of contributing to reduction of cooling air, improvement of fuel consumption, and CO2 reduction by providing turbine blades with high cooling performance structure, studies were given on the transpiration cooling structure to multiply the layers of mono-crystalline materials having high mechanical strength and durability to realize a structure artificially close to porous materials. The discrete control system was also discussed to improve the fuel consumption. (NEDO)

  1. FY 1999 report on the results of the introductory study on the global environmental industry technology. Investigational study on the environmental creation technology by the application of ecosystem information functions; 1999 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu seika hokokusho. Seitaikei joho kino oyo ni yoru kankyo sozo gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To know the state of environmental pollution before it clearly exists, an investigational study was made on the technology to measure environmental stress at high sensitivity, in wide range and at high speed using functions to respond chemical substances, etc. which living organisms have. The FY 1999 results were outlined. As to the application of ecosystem information functions, survey was conduced paying attention to the environmental stress response of each of the bacteria, algae, plants and animals, responses viewed from the manifestation of immunity antibodies which occurs inside living organisms and changes at genetic level, and responses of algae and plants in case of specifying environmental pollutants. In relation to the application of the biological amplification mechanism, survey was carried out on environmental stress signals sent from plants, selection of environmental stress index plants, detection of environmental pollutants using bacteria, high sensitivity detection using animal (nematode), etc. Concerning the standardization of the environmental measuring technology by the application of ecosystem information functions, survey was conducted on artificial molecular recognition sensor, antibody device sensor, biochips, system construction, etc. (NEDO)

  2. Report on a fiscal 1995 basic survey of the environmental engineering. Investigational study on the systematization of the environmental business related information; 1995 nendo kankyo business no engineering ka kiso chosa hokokusho. Kankyo business kanren joho no system ka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    An investigational study was conducted on directionality of arranging the environmental business related information, based on the analysis of the status of arrangement of the environmental business related information and the examination of the needs for the environmental business related information. As the directionality of arranging the environmental business related information which is most suitable for enterprises and research institutes to use, the following were considered: (1) arrangement of a system for effective use of the information owned by environmental related organs; (2) arrangement of a system for supply of the environmental business related information mainly to medium and small companies; (3) arrangement of the environmental business related information forum. In (1), it is necessary to arrange the system for the joint use of information owned by each institute. In (2), the tackling with the environmental business should be supported by arranging the system for information supply from big companies to medium and small companies. In (3), it is necessary to arrange the information forum, and it is necessary to control information thoroughly for the management for prevention of bad deeds of brokers. 7 refs., 19 figs., 21 tabs.

  3. Research report of FY 1997 on the clean coal technology promotion project and region model survey. Measures for environmental load reduction: feasibility survey on the environmental load reduction-type utilization Energy Center (interim report); 1997 nendo chosa hokokusho. Clean coal technology suishin jigyo chiiki model chosa `kankyo fuka teigen taisaku: kankyo fuka teigengata sekitan riyo energy center feasibility chosa` chosa hokokusho (chukan hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey has given an eye to the coal that it can be easily burnt together with combustible waste and supplements unstable generation of waste. Thus, the establishment of the Energy Center at the place where infrastructure of coal will be arranged, a lot of combustible waste will be expected to generate and a considerable aniybt if energy will be used, has been planned, and this survey is intended to study the scale of Energy Center, its economy and the problems to be solved. In power plant project using RDF for above-mentioned local governments, the construction of power plant and the renewal time of the existing incinerator to RDF facility can be planned separately in this system. The power plant will be economically constructed and the amount of coal can be decreased in accordance with increased RDF to meet wide range of refuse treatment. In FY 1997, the actual situation of the waste treatment and the infrastructure of coal supply was surveyed, and selection of the place suitable for the Energy Center and its scale was studied. 69 figs., 50 tabs.

  4. FY 2000 report on the survey project on the environmentally friendly energy community, excluding mostly projects on electric power generation. Survey project on the environmentally friendly energy community in the Nagoya area; 2000 nendo kankyo chowagata energy community chosa jigyo 'shutoshite hatsuden jigyo ni kakawaru mono wo nozoku' chosa hokokusho. Nagoya chiiki ni okeru kankyo chowagata energy community chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper studied the working-out of the basic plan on the RPF (refuse paper and plastic fuel) production business in the area mainly including Nagoya city and of the business profitability. RPF is a solid fuel made by grinding, mixing and pressurizing paper and plastics in appropriate sizes. Its shape and calorific value can be adjusted according to the needs. In the Nagoya area, the demand for RPF is more than the supply, and therefore a much larger amount of RPF is in need. In Phase 1, business was studied for paper and plastics in the container packing paper waste and business-derived general waste. As a result, the RPF production amount was 21,000 t/y, which is equivalent to the effect of reduction of the same amount of coal. As to the profitability, it was made clear that the business can be profitable if collecting 41,400 yen/ton as the re-commercialization cost. In Phase 2, the design of the facilities was made for the larger-sized commercialization by adding industrial waste plastics to the waste in Phase 1. (NEDO)

  5. Achievement report for fiscal 2000 on research and development of environment compatible next generation supersonic propulsion system. 1/2. Research and development of environment compatible next generation supersonic aircraft engine; 2000 nendo kankyo tekigogata jisedai choonsoku suishin system no kenkyu kaihatsu seika hokokusho. 1/2. Kankyo tekigogata jisedai choonsokukiyo engine kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 in development of an environment compatible next generation supersonic aircraft engine. In reducing noise, discussions were given on noise absorbing materials, jet mixer ejector nozzles, and fans. In order to reduce NOx emission, studies were performed mainly on stable combustion of an HTCE combustor. Reasonability of the AI control was verified by using simulations of a combustor model. Design was made on a fuel AI control system required to avoid such unstable combustion as backfire and spontaneous ignition. A CMC liner for an innovative heat resistant combustor was discussed. In the CO2 emission suppressing technologies, studies were performed on technologies to apply to large structures such three-dimensional fiber reinforced materials as MMC, CMC and TiAl. In developing damage tolerating design technologies for the advanced heat resistant material structures, studies were made on application to turbine structures of micro-structural stabilization for an extended period of time, heat insulation/oxidation resistant coating, micro and macro organization control and crack propagation analysis. The paper also describes an overall demonstration studies on technologies for very fine cooling of pseudo microporous structure, discrete control for CO2 reduction, an environment compatible engine systems and engines. (NEDO)

  6. Feasibility study of environmentally friendly type coal utilization systems. Feasibility study of environmentally friendly type coal utilization systems in sectors except the coal industry in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku no sekitan kogyo igai no bumon ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of working out a comprehensive master plan for application of the coal utilization system, the paper surveyed and studied the coal utilization system in terms of environmental measures and efficiency improvement in the utilization of coal. As a result of the discussion with NEDO and the National Planning Committee of China, Liaoning Province (the whole China) and Shenyang City were selected as a model area and a model city for the survey and study. As energy conservation measures taken in the former, desirable are intensifying/capacity-increase of boilers, kilns, etc. and adoption of new-type/high-efficient equipment. Also expected are reinforcement of combustion control and improvement of efficiency by using coal preparation, industrial use coal briquette, etc. Measures taken in the latter are the same as those taken in the whole China. As SOx reduction measures for Liaoning Province, desirable is installation of dry-type desulfurization equipment and simple desulfurization equipment. As dust prevention measures for it, desirable is installation of electrostatic precipitators or high-functional bag filters. SOx reduction measures for Shenyang City are the same as those taken in the whole China. SOx can be reduced by using coal-prepared low-sulfur coal and industrial use coal briquette added with desulfurizing agent. 88 figs., 163 tabs.

  7. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    The paper surveyed the present situation and future trend of economy, energy supply/demand, coal production/distribution/utilization and the environmental effects in Thailand. The survey on the coal utilization and its environmental effects was partially requested of the environmental research institute in Thailand. The amount of coal utilization in Thailand rapidly increased to nearly four times as large as that ten years ago mainly in terms of domestic lignite under the government`s policy on expansion of the domestic energy use. However, most of this domestic lignite is low-grade coal with low calories and high sulfur content, and the use of it was rapidly increased mostly in power generation sector without no adequate environmental measures taken. This caused an environmental problem on air pollution due to sulfur oxides at Mae Moh power plant in the north several years ago, and the damages to the regional residents, etc. were given much publicity by journalism and developed the social problem. Accordingly, Thai people are now critical of the coal resource exploration and the coal use expansion. Under the circumstances, the Ministry of Industry and the energy related ministries/offices are obliged to review their development/promotion plans. 84 figs., 99 tabs.

  8. Fiscal 1997 feasibility survey of an environment friendly type coal utilization system. Feasibility survey of the environment friendly type coal utilization system in Malaysia and Vietnam (case of Vietnam); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Vietnam ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper grasped the state of coal utilization by coal consumption field, the state of coal physical flow in Vietnam, etc., surveyed/studied a possibility of introducing the environment friendly type coal utilization system, and assessed the possibility. As to energy resources, the north is abundant in hydroelectric and coal (mainly anthracite) resources, and the south in oil and natural gas resources. Coal production in fiscal 1997 is planned to be 10 million tons. Coal preparation technique presently available is only grain size sieving. Accordingly, it is necessary to study for heightening efficiency of facilities and modernizing facilities in accordance with the introduction of the environment friendly type coal utilization technology. During the study, it is possible to propose improvement on coal processing technology (coal preparation technology). Assessment and study are made especially of the coal selection system, fine coal recovery system and waste water treatment system. For the plan on new coal-fired power plants (300MWtimes4), there is left much necessity of proposing studying models considered of the anthracite combustion technology and environmental improvement and of assessing/studying them. 60 figs., 117 tabs.

  9. FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports presented to the international forum held by RITE); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishihn jigyo kokusai seminar shiryo. RITE chikyu kankyo kokusai forum hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research Institute of Innovative Technology for the Earth (RITE) has been inviting creative, advanced research projects still in the early stage on an international scale to raise the research seeds for global environment preservation, and promoting the selected themes. The organization has invited the domestic authorities and researchers for the research projects selected from abroad as the good projects in the areas of biology and chemistry, to hold the international forum in March 2001. The keynote lecture in the area of biology addresses the latest researches on plant and life science, stressing how the researches contribute to global environmental problems. The keynote lecture in the area of chemistry addresses possibility of establishment of energy resource cycles utilizing the natural force of the earth. The last lecture introduces the research results by the environmental catalyst research group of RITE. The forum has animated questions and answers in the lectures selected as the good research projects. (NEDO)

  10. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system. Potential survey of the environmentally friendly type coal utilization system in the Philippines; 1999 nendo chosa hokokusho. Kankyo chowa gata sekitan riyo system kanosei chosa (Firipin ni okeru kankyo chowa gata system kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of contributing to working out a master plan for the introduction of the environmentally friendly type coal utilization system in the Philippines, analysis was made of the state of coal use/the state of spread by industry mostly including the electric power industry, cement industry and residential/commercial use fuel sector. In the Philippines, the amount of coal use has rapidly been increasing since coal-fired power plants started operation. For the promotion of the use of domestic coals, it is important to reform low grade coal. Moreover, the technology is required which copes with the reinforced regulation against SOx emissions. In the cement industry, coal and coal ash have not yet been effectively used. Therefore, the following measures should be taken to increase the competitive force: energy conservation measures, reinforcement of environmental measures such as dust prevention, and effective use of the fly ash emitted from power plants. In general households and small-/medium-sized industries such as tobacco drying, they still use a large amount of charcoals and firewood, which is approximately 86% of the residential/commercial use energy. There is a growing tendency for the development/spread of coal briquette as substituting energy. (NEDO)

  11. Fiscal 1998 R and D project on global environmental industrial technology. R and D result report on environment- friendly production technology (advanced chemical synthesis reactor); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bio reactor) kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For high-efficiency production of substances by bioreactor, study was made on a bio-control mechanism as its elementary technology. On the study of breeding technology by expression control, the structure design of a control region and development of new expression vectors had been finished, and study was made on breeding of high-efficiency recombinant production cells by using candidate expression vectors. On the study of breeding technology by multi-stage enzyme reaction control, the enzyme gene of a system synthesizing cysteine from glycerol was searched, and hydroxypyruvaldehyde hydrogenase gene was isolated as substance production model. Cysteine production Escherichia coli combined with serineacetyl transferase gene was also prepared. In addition, study started on cloning of hydroxyacetone oxidase gene. On development of reactor system technology, for conversion of serine to cysteine, study was made on optimization of a reaction condition by theory of enzyme reaction rate. (NEDO)

  12. Leading research for fiscal 1998 on innovative technology for the earth. Researches on technologies for creating ecology using ecosystem's information transmitting function; 1998 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu. Seiteikei joho kino oyo ni yoru kankyo sozo gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to develop a technology for detecting environmental pollution before it becomes apparent and thereby to contribute to the development of technologies to minimize the damage that may be inflicted upon the global environment. For this purpose, researches are conducted in search of techniques to detect, at high speed with high sensitivity over a wide scope, the response of living organisms to chemicals. In a research on the application of the reaction of ecosystem to environmental stress, communication between living organisms in coping with environmental chemicals is investigated. It is then found that the growth of vegetable roots may be used as a measure for the detection of environmental pollutants but that the method is too low in sensitivity. A research is conducted on the creation of an ecological reporter function using the biological amplification technique. It is then found that the immunoreaction-aided measuring of environmental pollutants yields an excellent result in terms of sensitivity but that it has a problem in its resistance to environmental conditions. In a research on the standardization of environmental measurements using ecological information, it is found that the primary object of research and development should be a systematization technology compatible with biological functions. (NEDO)

  13. Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

  14. Report on a project to support promotion of forming an environmentally friendly energy community. Survey on an environmentally friendly community business by means of high-efficiency wastes power generation system in the Toyota-Kamo wide area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Toyota Kamo koikiken kokoritsu haikibutsu hatsuden kankyo chowagata energy community jigyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Taking the Toyota-Kamo wide area as the object, wastes power generation is positioned over the society system as worked on by administrations and operators integrally to incinerate mixedly those incineratable materials such as plastics among general and industrial combustible wastes for high-efficiency generation of power, which is supplied to electric utility operators as surplus power. Discussions were given on the business feasibility and the effectiveness as a society system. In this area, the mixed model B plan (dealing with general wastes plus industrial wastes) was evaluated as an effective plan as the society system. This is because the plan has effect to incinerate, melt and generate power from industrial wastes which have been used for land-fill, effect of improving the power generation efficiency, and effectiveness of mixed treatment with general wastes. The plan A in which general wastes are made into RDF, then incinerated mixedly with industrial wastes for power generation was evaluated to have high reliability potential of power supply and to be an effective plan as a society system, if effect can be expected to reduce transportation energy as a result of making the system large enough and turning wastes into RDF. (NEDO)

  15. Leading research for fiscal 1998 on innovative technology for the earth. Researches on technologies for creating ecology using ecosystem's information transmitting function; 1998 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu. Seiteikei joho kino oyo ni yoru kankyo sozo gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to develop a technology for detecting environmental pollution before it becomes apparent and thereby to contribute to the development of technologies to minimize the damage that may be inflicted upon the global environment. For this purpose, researches are conducted in search of techniques to detect, at high speed with high sensitivity over a wide scope, the response of living organisms to chemicals. In a research on the application of the reaction of ecosystem to environmental stress, communication between living organisms in coping with environmental chemicals is investigated. It is then found that the growth of vegetable roots may be used as a measure for the detection of environmental pollutants but that the method is too low in sensitivity. A research is conducted on the creation of an ecological reporter function using the biological amplification technique. It is then found that the immunoreaction-aided measuring of environmental pollutants yields an excellent result in terms of sensitivity but that it has a problem in its resistance to environmental conditions. In a research on the standardization of environmental measurements using ecological information, it is found that the primary object of research and development should be a systematization technology compatible with biological functions. (NEDO)

  16. Investigations in fiscal 2000 on feasibility of environment friendly coal utilization system. Feasibility survey on environment friendly coal utilization system in India; 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Taking the area of the clean coal technology (CCT) effective for energy conservation and environment preservation as the object, a feasibility survey has been performed on executing a model project in India. About 70% of the total power generation capacity in India depends upon coals existing in abundance inside the country. Since the local coals are high in ash, low in sulfur, and low in calorie, the environmental problem related to thermal power plants is the disposition of fly ash. The Central Electricity Authority of India expects solving this problem by CCT introduction. It also expects increase in combustion efficiency by using ultra-critical boilers. The Indian cement industry often uses in-house electric power generation facilities because of high electric power cost, wherein the produced coal ash is used as a cement raw material. The matter of the strongest interest is the introduction of a high-efficiency combustion system that depends on low-grade coals. Among the CCTs, strong interest was shown in the fluidized bed cement kiln and the circulating fluidized bed boiler. The iron and steel industry has expectations toward effective coal washing technologies and coke manufacturing technologies. (NEDO)

  17. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Grasping the present situation of coal utilization technology in the Philippines, the paper proposed a feasibility study of introduction of the environmentally friendly type coal utilization system which seems to be needed in the future. (1) Introduction of the environmentally friendly type coal utilization system in the electric power generation sector: there are only four full-scale running coal thermal power plants in the Philippines. In the future, several coal thermal plants are planned to be constructed by 2005, but for the new installation, it is desirable to adopt fluidized bed boilers with wide application to coal kinds. In case of 0.3-1.0 million MW class plants, it is planned to adopt high grade import coals, and it will be natural to fire pulverized coal. For the processing of flue gas, it is a must to install desulfurization facilities and smoke/soot removal devices. (2) Utilization/development of domestic low grade coals: at the mine-mouth generating plant, it is necessary to investigate the economically minable amount of coal, confirm productivity, survey coal quality, etc., and select boiler. As to coal briquetting technology, it is necessary to examine coal quality for tests and make a thorough study of what technology is most suitable. 50 figs., 78 tabs.

  18. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

  19. Study to take environmental symbiosis into consideration on housing construction. No.2. Experimental study on the thermal performance of K house in winter season; Kankyo kyosei ni hairyoshita sumai zukuri ni kansuru kenkyu. 2. Amagishi ni tatsu K tei no toki no onnetsu kankyo keisoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, K; Ishihara, O [Kumamoto University, Kumamoto (Japan)

    1996-10-27

    For the construction of houses that effectively utilize natural energy and impose less load on environments, an example of house building respecting environmental symbiosis is described. Reported herein are a heating system and the measurements of thermal environment in winter. In winter, the floor is heated by warm water from solar heat collectors circulating in pipes buried in downstair underfloor RC foundation. For the verification of the heating effect, comparison was made between the heater-provided southeast (SE) room and heater-unprovided northeast (NE) room, both downstairs. Warm water circulated in the underfloor pipes only in the daytime, the pipe surface recording the maximum of 32{degree}C in the daytime and the minimum of 17{degree}C early in the morning. At midnight, the SE room was warmer than the NE room by 2{degree}C. The slab surface in the SE room recorded 28{degree}C at the maximum and 17{degree}C at the minimum, but the temperature remained constant at 10{degree}C in the NE room. The rubble temperature was 17.5-20{degree}C in the SE room and approximately 11{degree}C in the NE room. It was noted that the SE room floor slab was capable of heat accumulation. The resident is a devotee of environmental symbiosis with mindset for enhancing natural energy utilization, burning an oil heater and a fireplace but intermittently. 1 ref., 12 figs., 1 tab.

  20. FY 1999 Project of information exchange by researchers on environmental problems in the Asia-Pacific region. Report on investigations for establishing Environmental Technology Research Network in the Asia-Pacific Region; 1999 nendo Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho. Asia/Taiheiyo chiiki kankyo gijutsu kenkyu kaihtsu network kochiku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the results of the FY 1999 activities for the project of information exchange by researchers on environmental problems in the Asia-Pacific region. In 1999, the 6th International Workshop was held in City of Yokkaichi, Mie Pref., with the theme (Implementation of international collaborative researches on environmental technology) at International Center for Environmental Technology Transfer, with a total of more than 50 domestic and foreign attendees actively participating in the discussion. The keynote addresses were (Use of coal and environmental improvements) presented by Mr. Yoshisada Nitta, Director at Central Research Institute of Electric Power Industry, and (Potential of clean fuel from biomass) presented by Dr. Kyu-Wan Lee of Korea Research Institute of Chemical Technology. The overseas surveys were conducted to promote the use and registration of the databases, and to identify problems by the on-the-spot investigations in Vietnam, the Philippines and Republic of Korea. At the same time, the mini-workshops were held for information exchange with the research institutes. It is keenly felt that Environmental Technology Research Network in the Asia-Pacific Region (ENTERNET-APR) works certainly in various areas, with the attendees in the last workshops serving as the key persons. (NEDO)

  1. Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Environmentally acceptable coal utilization system feasibility survey in Malaysia and Vietnam (Malaysia); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Malaysia ban))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In this survey, the coal utilization status in individual consumption sectors and coal distribution status in Malaysia are summarized as basic data for the introduction of environmentally acceptable coal utilization systems. In this fiscal year, the status of existing coal utilization technology and environmental issues in Malaysia are summarized as basic data for the introduction of above-mentioned systems on the basis of data and information collected by basic research and site survey in FY 1996. Malaysia is one of the rich countries producing the primary resources with crude petroleum, natural gas, hydro-power, and coal. The coal demand will be realized after saturating LNG development since 2000. The major coal consumption industries are power generation sector and cement industry sector. As expected increase in the future coal consumption, efficiency of coal utilization and environmental issues are problems in the future. Based on the FS results of this survey, the survey will be continued for planning and conducting the model project required from Malaysia. 8 figs., 34 tabs.

  2. FY 1998 survey report. Survey on reduction in environmental effect of greenhouse effect gas by the transfer of environmental technology in the Asian region; 1998 nendo chosa hokokusho. Asia chiiki ni okeru kankyo gijutsu iten ni yoru onshitsu koka gas no kankyo eikyo keigen ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Effects of the transfer of environmental technology were studied as an important policy for control of greenhouse effect gas in the Asian region. As schemes, those that were drew up by NEDO, JICA, etc. now exist and are used also in Japan. However, for the control of greenhouse effect gas emission which is expected to rapidly increase in future, it is indispensable to construct a new powerful and effective scheme in which technology transfer and fund to be given are organically connected. Especially, in the U.S., etc., the assistance of developing countries of a huge amount of money such as Japan's ODA is not extended. However, they position the environmental technology as an important strategy and is developing the assistance of developing countries by technology transfer and eco-business of private companies. Also in the eco-business field, the environment-related technology of Japanese companies is used in Asian developing countries, with expectations of its being a new business with international competitive strength. This is the subject for the whole global environment, and an important subject also for Japan which requires the creation of a new business field with international competitive strength. (NEDO)

  3. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  4. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  5. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  6. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  7. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  8. Fiscal 1999 geothermal energy development promotion survey. Report on environmental impact survey - 5 (Musadake area); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.B-5 Musadake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    For the purpose of clarifying the environmental impact to result from the digging of borehole N11-MD-3 in Shibetsu-gun, Hokkaido, a survey was conducted of changes in (1) hot spring water quality, (2) noise/vibration pollution, and (3) air pollution due to hydrogen sulfide, before and after the digging period. Under item (1), measurements were made at four hot springs, which involved weather, air temperature, water temperature, amount of welled-up water, pH, electric conductivity, etc. Although minor changes were observed during the measuring period, none was found related to the digging process. Under item (2), noise levels were measured during the drilling period along the site boundary, at a point 500m from N11-MD-3, the Kawakita hot spring, and the entrance of Sekiyunosawa. Along the site boundary, they were 55-60 dB during the drilling period, and there was an increase of 30dB attributable to the drilling. At the 500m point, there was a 15-20dB increase attributable to the same. Vibration levels during the drilling period were 40dB along the site boundary and less than the observable minimum at the other points. Under item (3), at four points along the site boundary (50m), hydrogen sulfide concentration in the air fluctuated by 0.01-0.21ppm when the steam discharge rate was 4.47-7.20t/h. (NEDO)

  9. Report of a project for the technical development of the environmental preservation and resource effective utilization system in fiscal 1995; 1995 nendo kankyo hozen shigen yuko riyo system gijutsu kaihatsu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper outlined the present situation of industrial waste all over Japan and the present situation of industrial waste of large urban areas where it is most difficult to secure places for the final disposal, and conducted an analysis on the present and future amount of final disposal waste. According to the literature from the Ministry of Health and Welfare, `research report on the discharge/treatment situation of the industrial waste` and `research results of administrative organizations for industrial waste,` the situation of final disposal from the past to the present was outlined and analyzed to study the future trend. Out of the administrative divisions of Japan, four divisions, which are all typically called large urban areas, were selected, and the situation of industrial waste in large urban areas was outlined and analyzed according to the questionnaire survey and the literature on industrial waste obtained from each administrative division. The survey by the Ministry of Health and Welfare indicated that the volume of the industrial waste discharged from the whole country amounted to approximately 400 million tons in fiscal 1992. However, helped by the improving recycling of waste construction materials, the amount of final disposal around 2000 is presumed to be less by 20% or so than that in 1992. 58 refs., 5 tabs.

  10. Manufacturing facilities of pharmaceutical products and measures for purification of its environment. Validation for sterilizing grade filter; Iyakuhin no seizo shisetsu to kankyo seijoka taisaku. Mekkin`yo firuta no barideshon

    Energy Technology Data Exchange (ETDEWEB)

    Nishiyama, M.

    1994-07-31

    Validation is defined as firm establishment of a documentary evidence showing the system concerned is functioning as designed. Validation for sterilizing grade filter is not limited only to validation of the filter itself, but evaluation of its extract as well as adsorption and the sterilizing condition of the filter and system are the items to be examined. It is necessary to make validation of the filtering system as a whole taking into consideration any kind of element of composition in order to reach the target. In this article, in order to avoid description on diversified subjects, only validation for the filter is focused and its technique is introduced. The procedure for executing validation is stated first, and concerning validation for the sterilizing grade filter, a bacterial retention test is explained in detail, then with regard to an integrity test, sterilization of the devise concerned and pharmaceutical suitability/extract tests, the points which call special attention and testing items are introduced. Finally self inspection and evaluation of operating performance qualification are described. 13 refs., 7 figs., 2 tabs.

  11. Achievement report for fiscal 1999. Research and development of high-performance magnetic materials creation technology making use of microgravitational environment; 1999 nendo bisho juryoku kankyo wo riyoshita koseino jisei zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to develop the above-named technology so as to improve on performance of magnetic materials for magnets extensively used in electric motors to consequently influence their energy conversion efficiency. For this purpose, probes are conducted into novel alloy phases, intermetallic compounds, and microstructure in a containerless coagulation process in which a molten body of a magnetic metal material in free-fall is allowed to cool rapidly, and a system is developed to enable a series of processes of heating and melting in preparation for containerless coagulation, specimen formation, and then coagulation in a microgravitational environment. The system is used for the study of novel materials for magnetic alloys and process technology. For the utilization of containerless coagulation in a microgravitational environment, it is necessary to make full use of the JAMIC (Japan Microgravity Center) facilities, and an experimenting apparatuses are fabricated for a containerless coagulation process and unidirectional coagulation process applicable to a free-fall test. In this fiscal year, some significance involving for example structural uniformity are found among the specimens created using containerless coagulation in a microgravitational environment, and it is inferred that the data as an index of higher performance will lead to studies in the next fiscal year and afterward. (NEDO)

  12. FY 2000 project on the research cooperation for the environmental response type water resource effective utilization system; 2000 nendo kenkyu kyoryoku jigyo. Kankyo taiogata mizu shigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of prevention of water pollution, stable water supply in the Philippines, etc., developmental study was made of a waste water treatment/water recycling system, and the FY 2000 results were summed up. In the operational study of Pilot Plant 1, for the waste water in the papermaking process of used paper recycling plant, development was studied of a waste water treatment/water recycling system. There occurred problems on minuteness, outflow, etc. of anaerobic granules, but those were caused by malfunction of SS removal equipment at plant side. The problems were solved by increasing flocculation/precipitation facilities. As to Pilot Plant 2 of which the R and D are planned to be started in April 2001, the food processing plant was surveyed for study, and SYSCORE was selected. Relating to the waste water treatment test of Pilot Plant 2, researchers of the Industrial Technology Development Institute (ITDI) of the Philippines conducted it under the guidance of the experimental data analysis. Besides, the paper carried out the training for technology spread/acceptance, technology spread seminar, support study in Japan, etc. (NEDO)

  13. Report on fiscal 2000 geothermal development promotion survey. No. C-5 Appi district environmental impact survey (1st phase); 2000 nendo chinetsu kaihatsu sokushin chosa hokokusho - No.C-5. 1. Appi chiiki kankyo eikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-08-01

    For the survey of weather in the Appi district, Iwate Prefecture, observation data covering the last decade were collected at weather stations and the like, and characteristics of weather, climate, and natural earthquakes were learned. In the survey of fluctuation in the spa water level, studies were made about fluctuation in water temperature, spring water, and river water, and basic data were collected for the examination of the impact to be generated by geothermal exploration well boring and short-term discharge tests. In the survey of animal and vegetables, the habitation and distribution of animals and vegetables at sites planned for geothermal well boring were investigated, and data were collected for the evaluation of the impact to be imposed on them by well boring or the like. In the survey dealing with nature conservation and landscape, laws and regulations governing nature conservation were collected and put in an easy-to-use order, and seasonal changes in the natural landscape were photographed and recorded. In the survey of noise/vibration and ground fluctuation, the background values were measured prior to the implementation of geothermal well boring, discharge tests, and so forth. (NEDO)

  14. Research on the general analytical method of fossil fuel cycle from a viewpoint of the global environment. 3; Chikyu kankyo kara mita sogoteki kaseki nenryo cycle bunseki hyoka shuho no chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The general analysis/assessment method of a fossil fuel cycle was studied. Seven kinds of power generation plants such as LNG cycle and coal cycle ones, and four kinds of transport and treatment systems of recovered CO2 such as ocean and underground systems were studied as case studies on life cycle analysis. As data necessary for life cycle analysis, the database was constructed which stores the facilities and operational energy required for a total energy system from mining of fossil fuel to treatment of recovered CO2, and the quantity of environmental waste such as CO2 emission. As a result, the decrease rate of energy balance defined as ratio of input energy to power plant output was estimated to be 14-43% and 20-60% in LNG cycle and coal cycle, respectively. Even if the recovery rate of CO2 in power plants reached 80-90%, reduction of total CO2 emission was limited to only 20-40% because of CO2 emission during mining, liquefaction and transport of fuel. 168 refs., 48 figs., 102 tabs.

  15. Relationship of responsible Care and Environmental Management Systems Standard ISO 14001. Example of Sumitomo Chemical; Resuponshiburu{center_dot}kea to kankyo manejimento sisutemu kikaku ISO14001. Sumitomo kagaku no jirei

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Kazuo. [Sumitomo Chemical Corp., Tokyo (Japan)

    1999-01-15

    In the chemical sector, Responsible Care is propelled by the International Council of Chemical Associations (ICCA). The objective of Responsible Care is to improve the performance and reputation of the Chemical Industry in areas that impact on people and environment. Sumitomo Chemical is committed to supporting a continuing effort to improve the chemical industry`s responsible management of chemicals through the Japan Responsible Vare Vouncil program. One the other hand, ISO 14001 had been published on Aug.1996 and have adopted the ISO 14001 as national standards on Oct. 1996. Already 973 companies in Japan, 74 of them in the chemical sector, have been certified to ISO 14001. In this paper, I provides concise commentaries on how Responsible Care and Environmental management systems work in the chemical sector. (author)

  16. Relationship of responsible Care and Environmental Management Systems Standard ISO 14001. Example of Sumitomo Chemical. Resuponshiburu[center dot]kea to kankyo manejimento sisutemu kikaku ISO14001. Sumitomo kagaku no jirei

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Kazuo. (Sumitomo Chemical Corp., Tokyo (Japan))

    1999-01-15

    In the chemical sector, Responsible Care is propelled by the International Council of Chemical Associations (ICCA). The objective of Responsible Care is to improve the performance and reputation of the Chemical Industry in areas that impact on people and environment. Sumitomo Chemical is committed to supporting a continuing effort to improve the chemical industry's responsible management of chemicals through the Japan Responsible Vare Vouncil program. One the other hand, ISO 14001 had been published on Aug.1996 and have adopted the ISO 14001 as national standards on Oct. 1996. Already 973 companies in Japan, 74 of them in the chemical sector, have been certified to ISO 14001. In this paper, I provides concise commentaries on how Responsible Care and Environmental management systems work in the chemical sector. (author)

  17. Study of promotion of CO2 fixation by the environmental improvement in the coral reef area; Kansho chitai ni okeru kankyo kaizen ni yoru CO2 kotei sokushin no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Maruoka, T.; Ishitani, H.; Matsuhashi, R.; Yamada, K.; Komiyama, H.; Kraines, S. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1997-01-30

    A study was conducted on how to fix CO2 in the ocean using coral reefs. Coral reefs have extremely high primary productivity ( production quantity of organic matters by photosynthesis) and are expected to be resources to fix CO2 when the quantity of photosynthesis exceeds the quantity of CO2 emitted in association with formation of calcium carbonate skeleton. If organic substances produced in coral reefs are well carried into the open sea, those are settled down on deep beds, which enables the storage into the ocean. At the coral reef floating in the ocean, it is not very deep inside and the seawater stays there, but it has a steep depth outside. By the numerical calculation, an examination was made on how the waterflow changes when making the flow path of seawater between the inland sea and open sea. From the actual calculation of an atoll, it was found that seawater comes in and out from the open sea to the inland sea near the opening of the atoll in accordance with the high tide and ebb tide, but the water stays at the deep bottom of the atoll. When installing a channel with a 10m depth at the portion where the water flows softly, the seawater was actively exchanged. 6 refs., 4 figs.

  18. Fiscal 1990 technological survey report. Report on NEDO's 10th anniversary international symposium (New energy and global environment); NEDO soritsu 10 shunen kinen kokusai symposium hokokusho. Shin energy to chikyu kankyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-10-03

    Two lectures were given by Christopher Flavin (vice president for Research, Worldwatch Institute Inc.) and Hiroshi Takeuchi (chairman, LTCB Consulting and Research Institute Inc.), and a panel discussion was held by five panelists with Toyoaki Ikuta (The Institute of Energy Economics, Japan) as the coordinator. The themes were 'a sustainable energy strategy for the nineties', 'industrial structure change and energy problem', and 'new energy and the global environment'. The panelists were from Sweden, France, Thailand, U.S.A., and Japan. The main subject was energy security, in which discussion was held on the uneven distribution of oil resources in the Middle East and political instability in the region and on counter measures against global warming problem. The discussion on the latter subject showed that a limitation exists in the total consumption of fossil fuel in the world, and that energy policies were meaningless unless they were on a global scale. As the concrete measures, energy conservation technologies and regenerative energy utilization technologies need to be developed and spread, for which emphasized was the spread on a global scale, namely, the necessity of international cooperation and an international propulsion system. (NEDO)

  19. Report on a fiscal 1995 basic survey of the environmental engineering. Investigational survey on the improvement of the waste treatment system; 1995 nendo kankyo business no engineering ka kiso chosa hokokusho. Haikibutsu shori system no kodoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    The paper described the present situation of the waste treatment system for the environmental engineering and the problems. The final waste treatment plants are in the tighter and tighter condition, and therefore the waste treatment system ought to be changed to a system in which importance is placed on the size reduction, weight reduction, and recycle. Accordingly, the waste treatment system becomes more characterized as a resource feedback process, and should be given more credit as a system for production of secondary resource. The problem is arrangement of conditions of technology, cost and legislation system for smoothing such recycling flow. Of course, it is natural that the most important subject of the system is to secure the environmental preservation by the waste treatment. As future subjects, needed are understanding of the waste treatment as a resource reproductive system, relation with other industries, and review of the legislation system. In consideration of technology, cost and environmental loads, required are proposal of validity of the recycle level limit and a future image of the system structure, and policies for promoting and supporting the recycle business. 47 figs., 104 tabs.

  20. Fiscal 1998 research report. Feasibility study on next-generation environment-friendly urban transport systems; 1998 nendo chosa hokokusho. Jisedai kankyo kyosei toshi kotsu system donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research arranges recent public transport system technologies such as LRT, and clarifies their technical issues to be overcome and developmental courses, and the improvement effect of their energy efficiency and CO{sub 2} reduction effect by such measures to contribute to development of next-generation public transport systems. The outlines and features of LRT, monorail/trolley bus and AGT as existing public transport systems are arranged. In the EU, development of tramways using rubber tires is in promotion. The concept of a next-generation environment- friendly urban transport system is prepared based on features of every public transport system. Since a trolley system causes traffic congestion and environment deterioration, introduction of an independent transport system with fuel cell is necessary in the future. The technical issues and solutions for construction of the next-generation transport systems are analyzed. Fuel cell and ITS are important candidates. Substitution of the next-generation transport system for existing buses showed a CO{sub 2} reduction effect of 3.91 Mton/y in Japan. (NEDO)

  1. Fiscal 1999 survey report. Survey of environmental effect pertaining to survey for geothermal development and promotion (Hakusuigoe area); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kankyo eikyo chosa (Hakusuigoe chiiki) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey of environmental effect was intended to grasp actual state concerning some environmental factors that should agree with survey/development and also to assess its effect on the surrounding environment, particularly as a part of the 'stage C' in the 'survey for geothermal development and promotion', which was implemented by the Government for the purpose of guiding geothermal development by enterprises. This report compiles the plan details of the environmental effect survey to be conducted in the Hakusuigoe district, and presents proposals. The survey area is in the north of Makizono-cho, Aira-gun, in Kagoshima prefecture and situated about 3 km west of Onaminoike in Karakunidake, one of the peaks in the Kirishima mountain range. The Ogiri geothermal power plant is in the west of the site, a tourist spot Ebino Heights about 4 km northeast, and the Kirishima hot-spring about 4 km southeast. The location is in the national park, with a part designated as No. 2 and 3 class special areas. The environmental effect survey was divided broadly into such categories as fauna/flora, hot-spring water alteration and inland water, landscape, noise/vibration/subsoil, and air/water, and was further subdivided in accordance with the actual operations. (NEDO)

  2. FY 1999 report on the results of the development of technology of the environmentally friendly next generation small incinerator; 1999 nendo kankyo taio jisedai kogata shokyakuro gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of a next generation small incinerator of low dioxin emission. Concretely, the technology to be developed is for a next generation small incinerator of low dioxin emission in which the exhaust gas treatment system enabling various kinds of heat utilization is connected to the small incinerator mixing the fixed bed two stage combustion technology of industrial waste use low dioxin oxygen concentration control system and the high performance industrial furnace heat storage combustion technology. The trial-manufactured small incinerator has characteristics as follows: The incinerator can complement the decrease in efficiency in the wide-area refuse collection. It can remarkably reduce the emission of environmental pollutants such as CO2. It contributes to reduction in CO2 emission and reduction in fossil fuel consumption amount by effective utilization of exhaust heat. The incinerator is lower in price than the existing one of low dioxin emission type. The subjects are verification of the overall effect of the lower dioxin emission, verification of effects of reduction in CO2 emission and reduction in fossil fuel consumption amount by heat utilization, and study of the spread/promotion system. The report contains items of the development of an environmentally friendly next generation small incinerator and the evaluation survey for the commercialization, and photos as supplementary data. (NEDO)

  3. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium--Creation of key industries (Development of trace pollutant measuring device); 1998 nendo biryo kankyo busshitsu sokutei device no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For measuring trace pollutants and for establishing a simplified high-speed method of assessing their impacts, research and development efforts are exerted to build measuring devices to meet the purpose. In relation with air pollutants, researches are conducted to develop a passive sampler technology-aided measuring devices capable of on-site analyses of trace pollutants. For the development of microchips to be the nuclei of such devices, studies are conducted about a gas absorbing chip consisting of porous quartz glass and a passive sampler installed thereon, a chemical reaction chip on which absorbed NO{sub 2} ions react with a fluorescent reagent, and an optical detection chip capable of high-sensitivity detection of a fluorescent substance generated by an ultraviolet emission device. As the result, an A4 size prototype of a trace NO{sub 2} measuring device is developed using a fluorescence detecting microchip system. In addition, a simplified measuring device is developed, in which gas absorbed at a polymer film flows in a very thin plastic-formed channel to reach an electrochemical detection system for measurement, and the device is found to work effectively. (NEDO)

  4. Systematic arrangement of global environment measure technology. 3. Current status of methane generation and its effective utilization; Chikyu kankyo taisaku gijutsu no taikeiteki seiri. 2. Methane no hassei jokyo to sono yuko riyo no genjo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The status of the methane generation due to landfill with waste has been analyzed to investigate the actual circumstances of effective utilization of methane in the world and its possibility. The artificial generation of methane is 375 Tg per year among the total methane generation in the world, 535 Tg per year. The methane generation from the landfill with waste is 40 Tg per year, which becomes a rather large contribution. The methane generation from the landfill with waste in Japan is estimated to be from 130 to 520 Gg per year, which is a rather low value as a share in the world. This is caused by the sub-aerobic property of landfill in Japan, and the methane generation can be suppressed. Accordingly, there are no systems using recovered methane as energy source in Japan. In the USA, profitability of energy recovery can be established in 600 to 700 landfills among about 6,000 landfills. The methane recovery is practically conducted at more than 120 landfills. The recovered methane is used as a power generation fuel. 45 refs., 43 figs., 27 tabs.

  5. Fiscal 1998 research report. Research cooperation on car energy and environmental technology based on ITS technology in China; 1998 nendo seika hokokusho. Chugoku ni okeru ITS gijutsu wo mochiita jidosha energy kankyo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims at preparation of the car energy/environmental vision based on ITS (intelligent transport system) technology in China, enhancement of the transport planning ability of Qinghua University, and promotion of effective energy use in China. The following activities were carried out concretely: Survey on the actual traffic situation by Qinghua University, analysis of environment deterioration factors based on the survey result, estimation of a traffic environment improvement effect, study on traffic flow simulation technique based on traffic engineering, and study on traffic planning technique. As the diffusion strategy of ITS along Chinese circumstances, standardization and improvement of a multi- modal traffic system, navigation and its application system, and ETC (electronic toll collection) system are promising. Expectation for Japan and Japanese roles are as follows: Improvement of signal control, provision of information systems such as navigation, discussion on ITS technology such as ETC with Chinese specialists, and feasibility study on introduction of ITS technology for every Chinese district. (NEDO)

  6. Fiscal 1998 research report. R and D on advanced combustion technology under microgravity environment; 1998 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on explication of a combustion phenomenon by using a microgravity facility, and a combustor possible to realize advanced combustion technology. In the basic research composed of 5 themes by the international joint research with NASA, 52 drop experiments using JAMIC's facility and 100 drop experiments using NASA's 2.2s drop tower were carried out. The themes are composed of an interaction in droplet arrays combustion, combustion of binary fuel sprays, combustion characteristics of solid fuel, flame dynamics around a lean flammability limit, and mass transfer around a combustion field. In the experiment using the microgravity experiment facility and analysis evaluation of the experimental data, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit, formation mechanism of NO{sub x} and an advanced combustor. For applying a pre-evaporating/pre- mixing combustion system to a combustor for aircraft engines, studies were made on some issues such as improvement of a combustion stability, NO{sub x} discharge characteristics, and optimum fuel atomizing. (NEDO)

  7. FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This promotion project on the cooperative research aims at developing technology to efficiently extract and recover valuable metals including in large quantity in tailings of ores in the Republic of Kazakhstan in consideration of the environmental harmony. The support study in Japan was conducted as follows. As to the Nikolayevska low grade ore, high leaching speed and high leaching rate by grain refining were made possible. The coarse grain was also possible of leaching if leached for a long time. The sulfide froth is possible of leaching in fine grain and in the temperature range of 50 degrees C. The Zhezkent tailings were possible of leaching with sulfuric acid, by aeration, and in the range of medium temperature. The sulfide froth was possible of leaching in fine grain and at temperature of 50 degrees C. After filtration/washing and regrinding, high sampling rates of bulk concentrate and pyrite concentrate were obtained by sulfide flotation by zanthate. The Zhezkent copper concentrate was tested on various factors such as grain size, temperature, and washing/no washing, to confirm effects of bacteria. In the pre-observation test on Au and Ag leaching, cyanogen leaching test was conducted using Cu leaching residue. About Cu, studied were leaching (vat leaching, flotation froth machine agitation (temperature increase, bacteria)), solvent extraction, and electrowinning. About Au and Ag, studied were cyanogen leaching and process of adsorption of activated carbon. (NEDO)

  8. Fiscal 1997 international cooperation project. Report on the results of the research on environmental harmony type combustion technology; 1997 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Out of the R and D on the environmental harmony type combustion technology, the results of the project carried out in fiscal 1997 were summed up. In the site survey, etc., visits were paid to France, Spain, Greek, Germany, the U.K. and the U.S. to have discussions and examine the trend of research on the NOx removal catalyst and catalyst combustion. In the actual R and D, the R and D were conducted on zeolite base NOx removal catalyst, oxide composite base NOx removal catalyst, alumina base NOx removal catalyst, direct decomposition type NOx removal catalyst, catalyst combustion, etc. In the R and D of the catalyst combustion, durability under high gas flow flux was examined of PdO-Pt/Ba-Al203 catalyst developed for low temperature use, which indicated that durability and low temperature activity were heightened. As high temperature use catalyst, high temperature durability was examined of the developed Pd0-La/Gd-ZrO2 catalyst, which showed that the durability was favorable. 322 refs., 261 figs., 55 tabs.

  9. Fiscal 2000 achievement report. Environment-conscious industrial technology research and development project (Development of environmentally-friendly catalyst technology); 2000 nendo kankyo chowagata shokubai gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development and basic studies were conducted about novel catalysts which would help reduce impact on global environments. The efforts involved the development of (1) photocatalysts and (2) selective oxidation catalysts. In domain (1), a silicon semiconductor was manufactured for an integrated hydrogen generation catalytic membrane/silicon semiconductor/oxygen generation membrane system as a hybrid multilayer photocatalyst, and a fundamental one-layer type was fabricated. As for a system using a compound semiconductor CIGS (Cu(InGa)Se{sub 2})/CdS membrane, a CIGS membrane was completed, and CdS was deposited in layers to support platinum and it was found that water was decomposed under visible light irradiation although the bias voltage load was slight. In domain (2), the methanol and formaldehyde formation rates greatly increased when some MgO powder was installed in the reaction space in the vapor phase selective oxidation of methane in the presence of a catalyst which was a very small amount of nitrogen dioxide. (NEDO)

  10. Joint verification project on environmentally friendly coal utilization systems. Joint verification project on the water-saving coal preparation system; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    In this verification project, clean technology which should be spread in China was verified and the base structure for its spread was prepared for the purpose of controlling emissions of environmental pollutants associated with the coal utilization in China and of contributing to secure energy acquisition of Japan. As joint verification projects, a general rehabilitation type coal preparation system was installed in the Wangfenggang coal preparation plant, and a central control coal preparation system was installed in the Qingtan coal preparation plant. In the former, a system is verified in which optimum operation, water-saving, high quality, and heightening of efficiency can be obtained by introducing two computing systems for operation control and quality control, various measuring instruments, and analyzers to coal preparation plants where analog operation is conducted helped by Russia and Porland and have problems about quality control. In the latter, a central control system achieving water saving is verified by introducing rapid ash meters, scales, desitometers and computers to coal preparation plants having zigzag or heavy-fluid cyclon and connecting various kinds of information through network. For fiscal 1994, investigation and study were conducted. 51 figs., 9 tabs.

  11. Fiscal 1995 survey report on the environmentally friendly type coal utilization system joint demonstration project. Water-saving coal preparation system joint demonstration project; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This project makes demonstration of clean coal technology (CCT) in China and preparation for the base of its spread, controlled environmental pollution due to the coal use by the countries concerned, and contributes to stably secure energy of Japan. The paper made analog operation in the 1960s-1970s, supported by Russia and Poland, introduced two computer systems for operational control and quality control, densimeter, level meter, flow meter and analyzer to coal preparation plants having problems on productivity and quality control, made the optimum operational diagnosis for the plants, and at the same time, demonstrated the comprehensive rehabilitation type system by which water saving, high quality and high effectiveness are obtained. Various types of sensors such as rapid ash meter, scale and densitometer and computers are introduced to coal preparation plants which were recently constructed in China, have jig or heavy liquid cyclone as main preparation equipment and conducts operational control. There, the central control system was demonstrated in which various information collected in the central operation room and in-site equipment is combined by network for high-grade data processing and water saving is achieved. 50 figs., 11 tabs.

  12. Fiscal 2000 survey report. Research on laser-aided photolysis of environmental pollutant in liquid phase system; 2000 nendo ekisokei ni okeru kankyo osen busshitsu no laser hikari bunkai gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Experiments were conducted on laser-aided decomposition and removal of chemical substances in liquid phase systems on the assumption that there existed chemical pollutants in wastewater or water after washing burned ash. The aim of the research was to split carbon-chlorine bonds and break benzene rings, the two being the cause of harmfulness, and experiments were conducted using chlorophenol. The photolytic lasers were ArF excimer laser and KrF excimer laser. It was found that the reduction rate of chlorophenol in a water solution under excimer laser irradiation was 1.7 times higher under KrF laser than under ArF laser. For mediums other than water, isopropanol was used, more convenient than chlorophenol in separating organic pollutants from burned ash and the like. In this case, organochlorine compounds were generated at the beginning, but they disappeared when irradiation was prolonged. It was demonstrated that the laser-aided environmental cleaning technology would find a very wide scope of application as an effective photolytic means. (NEDO)

  13. Metabolism of pure sulfate-reducing bacteria in the presence of ferrous ions and environmental chages of the medium; Tetsu ion sonzaika ni okeru junsuina ryusan`en kangenkin no taisha to baichi no kankyo henka

    Energy Technology Data Exchange (ETDEWEB)

    Baba, F.; Suzuki, T. [Ajinomoto Co. Inc., Kawasaki (Japan). Technology and Engineering Lab.; Seo, M. [Hokkaido Univ., Sapporo (Japan). Graduate School of Engineering

    1996-10-15

    In this study, the pure sulfate-reducing bacteria were cultured in the medium with different Fe{sup 2+} concentration; shape and activity of the bacteria, the evolution amount of hydrogen sulfide directly related to the breath of the sulfuric acid and the change of the pH value in the medium were investigated during every time interval; and influence on the metabolism of the sulfate-reducing bacteria with Fe{sup 2+} was examined. As a result, the conclusions were obtained as follows: in the case of a medium with high Fe{sup 2+} concentration containing Fe{sup 2+} of 1.0{times}10{sup -2} molkg{sup -1}, the colloidal substance in which the main composition was considered as Fe(OH)2 were present, and they provided a comfortable place for the bacteria to grow. Correspondingly, in the case of a medium with low Fe{sup 2+} concentration containing Fe{sup 2+} of 3.6{times}10{sup -4} molkg{sup -1}, the colloidal substance was small and the number of bacteria was also few. The four kinds of shape of bacteria coexisted in the medium with increasing the culturing time. The hydrogen sulfide was mainly evolved by the bacteria with the comma like shape. During a period that this comma like bacteria actively moved, the hydrogen sulfide evolution increased. 13 refs., 6 figs., 1 tab.

  14. Survey report of FY 1997 on the global environmental industry technology development promotion project. International research exchange project; 1997 nendo chosa hokokusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (kokusai kenkyu koryu jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Exchange of personnel among foreign research organizations is significant for promoting research and development to create new research fields and to build new technological systems for the purpose of solving global environmental problems. For this purpose, researchers were sent/invited to/from international conferences and international symposiums related to global environmental technology and exchange of personnel with major foreign research organizations and universities was conducted under the cooperation of RITE and RITE-related researchers and related academic societies. Based on short-term invitation and sending of researchers as well as the feasibility study of researcher exchange, researchers were sent/invited on long- and mid-terms. As a result, exchange of personnel engaged in the latest research in Japan and overseas could be promoted. It was found that various researches are being conducted abroad in basic areas of global environmental technology. Since they are closely related to the research and development of industrial technology contributing to global environmental preservation promoted by RITE, it is important to establish a more efficient exchange system of researchers in the future. 91 refs., 38 figs., 14 tabs.

  15. FY 1998 geothermal development promotion survey. Report on the environmental effect survey (animals/plants, No. B-7 Kuwanosawa area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (doshokubutsu, No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey was conducted to estimate effects of drilling of geothermal exploration well on the environment, aiming at grasping the present state of environmental elements before the survey/development. As a result of the literature survey, the following distribution were confirmed in the fauna: 5 orders 10 families 19 species in the mammalia, 10 orders 25 families 73 species in the aves, 1 order 3 families 6 species in the reptilia, 2 orders 6 families 9 species in the amphibia, and 17 orders 179 families 719 species in the insecta. In the flora, a distribution of 132 families 670 species was confirmed. The results of studying the above indicated that in the fauna, there were 10 species such as antelope as valuable animal in the area surveyed and that it is necessary to pay much attention to the environmental preservation of the habitat for those animals in the well drilling associated with geothermal survey. In the flora, the 13 valuable animals selected as animal having a fear of extinction in the 'plant-version red list' were confirmed in the area surveyed and the periphery. Further, as to the plant colony, there are no important colonies in terms of preservation. In well drilling, important things are efforts exerted to restore to the original state of the area altered, prevention of the washed-away of mud water, etc., and efforts exerted to preserve the environment of vegetation. (NEDO)

  16. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

  17. Fiscal 1997 report on the environment friendly type coal utilization technology transfer project. Downstream field; 1997 nendo gyomu hokokusho. Kankyo chowagata sekitan riyo gijutsu iten jigyo (karyu bun`ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of supporting the introduction/spread of clean coal technology (CCT) in countries in Asia and the Pacific, engineers of the countries concerned were invited to Japan aiming to ferment the understanding of CCT and improve abilities of them. The project was carried out by NEDO, and managed by CCUJ. It has two courses. The manager course is for policy makers, management and senior managers. By assessing CCT and presenting a menu for economical efficiency, environmental arrangement for CCT introduction is made in working out policies and planning plant/equipment investment in the future. The engineer course is for policy planners, mid-class managers and senior engineers. It proposes data on which to base a decision in working out/planning CCT facilities, and at the same time ideas by which to reduce environmental loads by management of facilities, simple improvements, etc. The number of the persons invited are 21, that is, 8 from China, 5 from Indonesia, 4 from the Philippines and 4 from Thailand. After the training, future subjects were summed up

  18. Research report for fiscal 1998. Research into the feasibility of exchange of studies for the development and promotion of global environment-related industrial technologies; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kenkyu koryu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The above was conducted by Research Institute of Innovative Technology for the Earth (RITE). Worldwide collaboration is mandatory for the settlement of environmental problems for the earth, and RITE is positively promoting its interaction with research institutes abroad. In fiscal 1998, it sent research teams to government organizations and research institutes in Europe and America for studies there. A study in Europe involved the preparation of chemicals from CO2 by virtue of novel biotic reactions, and RITE's microbial molecular function laboratory plans to start a leading study in fiscal 1999. In relation with environmental impact reducing technologies using sunlight-aided photocatalysts, visits were paid to three research institutes in America. RITE itself has developed a powdered semiconductor catalyst and is engaged in the study of producing hydrogen by decomposition of water using solar energy. Concerning the production of saccharides out of farm wastes remaining unused, researches were made into the feasibility of joint studies with some advanced research institutes in America. Discussions were made about the performance- and stability-related improvement of enzymes usable for the decomposition of biomass, the analysis of biological environmental circumstances that substance yielding microbes find themselves in under anaerobic conditions, etc. (NEDO)

  19. New energy visions for the Town of Naie district. Human-friendly Town of Naie City by environment-friendly energies; Naiemachi chiiki shin energy vision. Kankyo ni yasashii energy ga tsukuru hito ni yasashii machi Naie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The new energy visions are drawn for Town of Naie, Sorachi-gun in Hokkaido, where the industrial sector (manufacturing industries) consumes more than 60% of the total energy consumption. By energy type, oil and others account for 80%. When arranged in the order of expected recoverable quantity, the new energies for the town include utilization of solar energy, photovoltaic power generation, wind power generation, and utilization of wastes, biomass energy (agricultural products) and snow energy. The basic guidelines for introduction of new energies are for health and welfare, clearing and utilization of snow, environmental education and bringing up talented persons, supporting the related entrepreneurs, and integration of new energy with promotion of energy-saving movement. The priority projects the town plans to promote include utilization of biogas and temperature-differential energy for the town's water purification center; foundation of the Naie eco-school; and drawing conceptions for utilization of underground heat, utilization of low-temperature and snow/ice energy, co-energy around the spa of Naie, and mega-solar and eco-park at the Sorachi housing complex. (NEDO)

  20. Leading research report for fiscal 1998. Research and study of ozone-aided technologies for creating amenity-rich environments; 1998 nendo sendo chosa kenkyu hokokusho. Ozon riyo kaiteki kankyo sozo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches were conducted aiming at the establishment of an ozone-aided highly efficient decomposition process for the persistent organic matters in municipal sewage and industrial wastewater. Tested for verification were advanced water treatment technologies of the biological function acceleration type and the effect of their combination with the accelerated oxidation method, conditions necessary for efficient operation, and water treatment apparatuses and systems for operating them at high efficiency. Some findings are stated below. With an ozone-aided process performed at the first stage of biological treatment, biological decomposition is accelerated for a rise in the persistent organic matter decomposition rate. This is nothing but a finding in the laboratory, however, and much remains to be disclosed concerning the optimum conditions, reforming of sludge to be generated, volume reduction of the same, etc. Another finding involves the acceleration of decomposition of persistent organic matters using ozone in combination with hydrogen peroxide, ultraviolet radiation, titanium oxide, and the like. There still remain numerous tasks to carry out, however, which relate to the investigation of the reaction mechanism, establishment of operating conditions and criteria for selecting oxidants, etc. As for ozone, remaining to be solved are the problems of generation cost, storage and preservation, and safety. (NEDO)

  1. Fiscal 2000 feasibility research on environmentally friendly coal utilization system. Seminar holding project (China: Zaozhuang, Yanshan, Jianshan, Jinzhou); 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Seminar kaisai jigyo (Chugoku Zhaozhuang, Yanshan, Jianshan, Jinzhou)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Seminars were held in China for the delivery of reports on the results of model projects with a view to popularizing the results of the clean coal technology model projects, which had been completed, for the purpose of contributing to the improvement on coal utilization technology and to the enhancement of environmental protection. The seminars took place at the sites of demonstration model projects just completed in China, namely, Zhejiang Huba Corporation (low-grade coal combustion system); Chaili Colliery, Zaozhuang Coal Mining Administration (CFBC - circulating fluidized bed combustion); Jinzhou Heat Power General Co., Ltd. (CFBC); and Beijing Yanshan Petrochemical Corporation (desulfurizing agent-added coal-water mixture system). At each of the project implementation sites, lectures were given on technical matters, technical know-how was exchanged, and study tours were organized to facilities concerned, which meant to promote the diffusion of the related technologies throughout China and, eventually, to contribute to the enhancement of environmental protection. The main subjects at the seminars included the introduction of GAP (green aid plan) projects in China, introduction of the outlines of technologies related to the model projects, verification and achievements, latest trends, and measures for the diffusion of the technologies. Study tours were made, and videos were shown relating to the local conditions. Every one of the seminars was successfully attended by 60-70 participants. (NEDO)

  2. FY 2000 report on the survey of a potentiality of the environmental harmony type coal utilization system. Dispatch of engineers; 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Senmonka haken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of contributing to improvement in coal utilization technology and environmental conservation in developing countries, a survey project on the dispatch of engineers was carried out, and the FY 2000 results were summed up. The survey was conducted in terms of the operational state of the model project already finished in China, the present state of the model project on the circulating fluidized bed boiler in Indonesia, and the strategy to be worked out for spread of clean coal technology (CCT). In China, it was confirmed that 10 sites where the project had been finished are in a state of the appropriate operation. Further, problems on each model were grasped/analyzed by questionnaire survey. The model project on the circulating fluidized bed boiler in Banyuwangi, Indonesia, has been suspended about three years, affected by the serious economic crisis. Survey was made and advice was given for the state of facility/equipment maintenance so that the facility/equipment can be used at the time of resuming the project. As to the strategy to be worked out for CCT spread, questionnaire survey and hearing were carried out for Japan-side makers. Study/analysis of subjects/important points for the spread were made. (NEDO)

  3. Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

  4. Report on the FY 1999 study of the decomposition/removal of environmental pollutants using laser induced chemical reaction; 1999 nendo laser yuki kagaku hanno wo mochiita kankyo osen busshitsu no bunkai jokyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the cleavage of carbon-chlorine connection and decomposition of benzene rings which are hazardous causes of the environmental pollutants represented by dioxins, the photolysis of gaseous phase chlorobenzene used as a model compound was made using KrF and ArF excimer laser. The decomposition is high efficiency, and ArF shorter in wavelength can be compounded twice-four times as fast as KrF. It was found out that in the system where oxygen exists, carbon monoxide, carbon dioxide, acetylene, hydrogen chloride, etc. are produced as decomposition products. From the results of the gaschromatographical analysis, chlorine compounds were detected as solid phase decomposition products. However, by the oxygen existence effect and laser shorter wavelength effect, the formation of polychlorinated aromatics was controlled, and chlorine compounds were made non-pollutant together with the composition. It was indicated that the environmental clean-up technology using laser is effective for making low-concentration environmental pollutants non-pollutant, and it is a method to clean up the environment which has a wide range of the application field. (NEDO)

  5. 1998 Annual Study Report. Surveys on seeds for global environmental technologies, including those for energy saving; 1998 nendo chosa hokokusho. Sho energy nado chikyu kankyo taisaku gijutsu no seeds ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The energy-saving and other global environmental technologies are surveyed by collecting relevant information from various institutes, both abroad and domestic, to contribute to development of ceramic gas turbines. USA has announced a climate change plan, based on the five principles, to promote utilization of high-efficiency technologies and development of new clean technologies. UK is promoting to improve energy efficiency, along with liberalization of its energy markets. Germany concentrates its efforts in the 'Program for Energy Research and Energy Technologies.' France places emphasis on prevention of air pollution and rational use of energy. The R and D trends at public institutes, e.g., universities, for global environmental technologies are surveyed, from which a total of 14 themes are extracted as the seed technologies. At the same time, a total of 9 techniques potentially applicable to the seeds are extracted by mainly reviewing JICST and patent information, and assessed. The R&D trends of the IPCC-related researchers are also surveyed, but provide no theme directly applicable to the seeds. Most of the related themes at the private and public institutes surveyed, both domestic and abroad, are concentrated on carbon dioxide. (NEDO)

  6. Report on regional new energy vision for Kawara town. Toward the creation of eco-symbiotic community (simplified version); Kawaracho chiiki shin energy vision gaiyoban. Kankyo kyoseigata shakai no sozo ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kawara town, Fukuoka Prefecture, in the hope that the industry, administration, and citizenry will be concerned with each other for the realization of an eco-symbiotic community. The fruits of endeavors exerted for this purpose are described in seven chapters, which are (1) the outline of surveys, (2) local characteristics of Kawara town, (3) policy toward introducing new energy, (4) measures for introducing new energy, (5) study of model projects, (6) introduction of new energy into Kawara town, and (7) efforts to realize the introduction. Described in chapter (5) are the introduction of photovoltaic power generation into primary and junior high schools, heat supply business utilizing waste heat from a plant, energy conservation at administration buildings, development of an activities program for people to learn energy related matters, and the results of studies conducted on the respective model projects. Concerning the activities program, several applications are considered, dependent upon who are to implement the program: volunteer students, local community leaders, experts, or administration officials. For the initial stage of learning under the program, a system is built under which experts, local community leaders, primary and junior highschool children, and their teachers cooperate with each other under the leadership of a project coordinator. (NEDO)

  7. Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

  8. Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (survey of the coal utilization in Pakistan); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Pakistan ni okeru sekitan riyo gaikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper made a literature survey, hearing survey, site survey/study on the coal in Pakistan such as the coal utilization system and the environmental situation, etc., and aimed at pre-examination for the survey of the introduction of the environmentally friendly type coal utilization system to be planned in Pakistan in the future. The examination, data collection and preparation were conducted in terms of the following items: the structure of coal consumption in energy supply, structure of coal consumption, mainly of domestic brown coal consumption, the situation of coal utilization by industry and by region, environmental problems caused by coal utilization such as air pollution, the trend of policies of environmental regulation, etc. The literature on the following was obtained and surveyed: the situation of economy/energy in Pakistan, coal utilization technology by industrial field, and environmental protection technology. The hearing survey was made to institutions concerned, corporation groups and men of learning and experience. Site surveys were conducted for the typically selected coal utilization equipment and existing environmental protection equipment. 66 figs., 56 tabs.

  9. Achievement report for fiscal 1999 on research and development of environment compatible next generation supersonic propulsion system; 1999 nendo kankyo tekigogata jisedai choonsoku suishin system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    This paper describes the achievements in fiscal 1999 in development of an environment compatible next generation supersonic propulsion system. In order to reduce NOx emission, AI combustion control was discussed to have fabricated the backfire and autoignition detection device. The SiC photodiode was selected for flame detection, and a heat and pressure resistant fiberoptic probe was fabricated to detect flames in a high-temperature high-pressure combustor casing. These devices were combined to fabricate the backfire and autoignition detecting device, and the verification test was performed. For the purpose of application to an innovative heat resistant combustor liner, a silicon carbide material reinforced with silicon carbide fibers was selected. For continuous ceramic fiber as a reinforcing material, the Si-Zr-C-O system was selected, and the chemical gas-phase impregnation process effective to enhance the fiber/matrix interface characteristics as the matrix forming method was used together with the inexpensive precursor polymer impregnating and sintering process. Investigations were performed on the advanced control functions to reduce fuel consumption as the development of CO2 emission suppressing technology, and on the trends in discrete control. In addition, the optimal engine control logic and the specifications for discrete system constituting devices to be evaluated as the prototype in the future were established. (NEDO)

  10. Survey report of FY 1997 on the feasibility of microbial biotechnology for reuse of environmental pollutants; 1997 nendo chosa hokokusho (kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology no riyo kanosei chi kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An investigation was conducted with the aim of elucidating the foundations for effective utilization of environmental pollutants or unused resources which are likely to be causal substances of environmental pollutants, as resources, using biotechnology. Composting of agricultural waste, production of microbial mycelium proteins and microbial fermentation materials were suggested as main examples of effective utilization of unused resources by microorganisms. Selection of active microorganisms in the livestock waste, clarification of the mechanism of action and the establishment of treatment conditions are essential to new developments in this field. In the field of marine products industry, it was pointed out that the recycling of waste using microorganisms and enzyme treatment is the most promising approach to the effective utilization of resources. In the field of food industry, applications as the culture media for mushrooms, for enzyme production and for the production of physiologically active materials as well as fuel were clarified. Was also pointed out the significance of studies on the microorganisms and enzymes in resources containing cellulose, hemicellulose and lignin, and the waste from these resources, lignocellulose. Were also proposed the composting of household waste, methane fermentation, and fermentative production of organic acid and hydrogen from waste. Possibility and significance of fermentative production of organic acid from sewage sludge were suggested. 314 refs., 46 figs., 33 tabs.

  11. Survey on the present situation and future outlook of energy/environment issues mainly on coal in the APEC region; APEC ikinai no sekitan wo chushin to suru energy kankyo mondai no genjo oyobi kongo no mitoshi ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the purpose of studying the energy supply/demand trend and the environmental problem relating mainly to coal in the APEC region, the paper surveyed the situation from the past to the present and outlooked the beginning of the 21st century. GDP in the whole APEC region increased at an annual rate of 3.4% from 1971 to 1991 and made a rapid growth of an annual rate over 7% especially in the non-OECD region. The supply/demand balance of coal, etc. in the non-OECD region is expected to be tight, and the energy price also to be higher. This will be a major factor causing hindrance to the economic growth of resource-importing countries. It is necessary to prepare the energy infrastructure. With the increasing coal utilization, it is feared that pollutants such as SOx, NOx and CO2 will increase, and it is necessary to introduce energy utilization technology/facilities which are high-efficient and environment-friendly and to expedite introduction of non-fossil energy. The APEC region, where the worldwide growth is expected, is a priming for the world development, and a policy which is well balanced in economic growth, stabilized energy supply, and environmental protection is needed for the region to achieve its sustainable growth. 50 figs., 24 tabs.

  12. Modeling of atmospheric corrosion environments and its application to constant dew-point corrosion test; Yagai taiki fushoku kankyo no modeling to sore ni motozuku teirotengata saikuru fushoku shikenho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Muto, I. [Nippon Steel Corp., Tokyo (Japan)] Sugimoto, K. [Tohoku Univ., Sendai (Japan)

    1998-08-15

    Recently, stainless steel is increasing its demand for corrosion resistant building materials. Then, as it is necessary to develop and accelerating testing method capable of accurately estimating weatherability at sea side area, such testing method has no been developed yet because of difficulty to quantify corrosive environment relating to atmospheric corrosion phenomenon. As air temperature and relative humidity in outdoor change in complex, specific temperature and relative humidity cannot be used for their representative values. And, construction of corrosive factors such as sea salt particles, and so on are also much different at each area. However, at coastal area, a dew water dissolving the sea salt particles, so called droplets of chlorides aqueous solution is formed onto material surface. Then, in this study, on a base of drying and humidity absorption behavior and daily change behavior of temperature and humidity in outdoor, modeling of atmospheric corrosion environment was tried. An accelerating testing method according to this modeling was developed, long-term weathering test was compared with the corrosion behavior of the same steel, and validity of a new accelerating testing method was evaluated. 22 refs., 12 figs., 2 tabs.

  13. FY 1997 report on the study on creation of inorganic materials under micro-gravity environment; 1997 nendo chosa hokokusho (bisho juryoku kankyo riyo muki zairyo no sosei kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on creation of new functional inorganic materials under micro-gravity condition in an underground non-gravity experiment center to develop new production techniques of inorganic crystalline thin film, fine glass particle, anharmonic alloy, spherical semiconductor and surface modified semiconductor thin film. The micro-gravity observation result was analyzed numerically of interference fringes of Cu ion around an electrode during electrolysis. Experimental data relatively well agreed with computer simulation data. Prototype CdTe thin film was prepared by electrolysis. The size control condition of fine true spherical glass particles was clarified by micro-gravity evaporation/condensation of glass. Pb-Zn system alloys as an anharmonic alloy were prepared under micro-gravity condition, however, no compound of Pb and Zn was found. A production equipment of true spherical single-crystalline semiconductor by melting cubic Ge under micro-gravity condition, and basic data of heating condition were obtained. Surface modified semiconductor thin film was also obtained by micro-gravity laser annealing of SiGe prepared by plasma CVD. 23 refs., 65 figs., 6 tabs.

  14. Report on the finally obtained results of the study of the basement technology for environmentally friendly type metal base material regenerative utilization; Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu saishu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    For the purpose of contributing to the resource recycling and global environmental preservation, the R and D of metal base scrap regenerative utilization technology were conducted, and the report on the finally obtained results was summed up. As to the technology to remove impurities by the solid phase treatment, the Cu removal rate of more than 96% was made possible by the low temperature fracturing technology, and that of more than 90% by the hue difference discrimination separation system technology. From the results of the FS on the low temperature fracturing technology applied to car scraps, it was found out that the present price condition is not economically efficient in the present price condition, but a possibility of achieving the removal rate of 54% in the initial plan was obtained if applying the hue difference discrimination separation system to the pretreatment. Concerning the Sn removal, the Sn removal rate of more than 70% was obtained by the gaseous phase sulfuration method, and that of more than 50% was obtained in Sn removal/Cu removal/Zn removal by the oxidation reaction method. The targets were achieved. Relating to the treatment of impurities by melting (liquid phase), the Cu removal/Sn removal technology under reduced pressure was effective in vacuum melting furnace of 2-ton scale, but the needs for the development of large capacity plasma torch were recognized in that of 40-ton scale for practical use. (NEDO)

  15. Achievement report for fiscal 2000 on research and development of environment compatible next generation supersonic propulsion system; 2000 nendo kankyo tekigogata jisedai choonsoku suishin system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 in development of an environment compatible next generation supersonic propulsion system. In order to reduce NOx emission, the AI combustion control technology was used to newly fabricate a pre-mixing and pre-evaporating tube model, whereas the backfire and autoignition detection device which has been fabricated on a trial basis was given a verification test in a high temperature and pressure site, whose condition is close to that in the actual combustor. A spectroscopic analyzer was used to sense flame light emission, and the operation was verified by using a model combustor. The basic discussion was given on a combustion control logic, whereas NOx reduction control was verified by using simulations. An Si-Zr-C-/Sic based CMC to be applied to an innovative heat resistant combustor liner was tested to have extracted items to be improved. In the CO2 emission suppression technology, logic design was made on a discrete control system, an engine performance optimization logic was developed, and its functions were verified. Detailed design was completed on a smart sensor to be tested in the HTCE engine operation. As the discussions on the engine system, verifications were given on the calculation of performance cycles during flight, estimation on NOx emission, the basic construction of the fan applied with metallic base composite materials, and the reasonability in the target of weight reduction. (NEDO)

  16. 1998 research cooperation project. Research cooperation on environment-compatible type water resource effective-utilization system; 1998 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of securing water stably and preventing water pollution in the Philippines, R and D were carried out on a wastewater treatment and water reclamation and reuse system which is easy to operate and maintain and low in cost through the research cooperation between the Philippine Industrial Technology Development Institute and Japan. According to the survey result of statistical data concerning water pollution load structure by industrial wastewater classified by the industry in the Philippines, enumerated are the food manufacturing industry, paper pulp manufacturing industry, and the textile dyeing industry as those greatly affecting water pollution in BOD exhaust and wastewater, etc. Consequently, with Ram Food Product Co. of vegetable processing and Solid Mill Co., of textile dyeing as plants to be studied, a wastewater treatment test was performed in a laboratory scale. From the result of the test, the pilot plant was basically designed to have 'anaerobic + aerobic treatment + tertiary treatment' for the treatment process, with an one-tank type UASB method used as the anaerobic treatment, with a sand filtration + activated charcoal treatment as the tertiary treatment, and with the cost effectiveness for water reuse set to be examined. (NEDO)

  17. FY 1998 international cooperation project for global environment/project to evaluate influence of climate change; 1998 nendo chosa hokokusho. Chikyu kankyo kokusai kyoryoku jigyo/kiko hendo eikyo hyokanado jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of the international cooperation for the global warming problem, evaluation/study were conducted on policy to lessen climate changes from viewpoints of scientific technology, environment, and economy/society. In the development of evaluation methods on cost analysis, the following were pointed out: Changes in resource utilization brought about as a result of the policy are all needed to be numerated; In resource, clean air and water, and also abolition of price barrier and prices now in force are included. As subjects on the technology transfer, cited are barriers in aspects of organization/system and barriers in aspects of economy/finance and society. Especially, it was pointed out that it is necessary to exchange the persons concerned in the industrial sector. Of various optional policies toward the prevention of global warming, the Kyoto mechanism not only has an economical merit of the use of low cost option but can be fairly promising from an environmental viewpoint of internationally controlling the greenhouse effect gas emission, if the characteristic of practically using the market can be so designed that it fulfills its function. (NEDO)

  18. Report on achievement for fiscal 1998. Global environment industry technology development promotion project (the advanced technology survey and research project); 1998 nendo seika hokoiusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (sentan gijutsu chosa kenkyu jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to structure innovative technologies to solve effectively the global environment problems, it is important to incorporate infra-structural technologies that have been achieved by universities and other research institutions. The fiscal 1998 project has commissioned 25 researches found superior from among research plans that have been invited during fiscal 1997. This paper enumerates the main themes including those under continued research. The research themes include: fixation of phosphor by using photo-energy, utilization of nitrogen fixing bacteria in rice plant roots for the purpose of carbon dioxide reduction, new functional solid ultra-strong acids for clean chemical processes, fixation of warming gases by using ultra critical fluid catalytic reactions, photo-catalysts having microporous structure, whose energy structure is controlled, waste water purification by using stimulation sensitive polymers, a practical and small high-speed environment purification system by means of a simple technology to cultivate high concentration bacteria of microorganisms, fundamental analysis of response to specific wavelength light in photosynthesized microorganisms, bio-remediation utilizing symbiotic systems of plants and bacteria, high efficiency catalysts purposed for total decomposition of water, and separation of carbon dioxide in deep sea bottoms by controlling hydrate crystal growth. (NEDO)

  19. FY 2000 report on the investigation of environmental effects in the geothermal development promotion survey. Tertiary. No.B-7 Kuwanosawa area; 2000 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho - No. B-7 Kuwanosawa chiiki (Dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    In the Kuwanosawa area, Yuzawa city, Akita prefecture, survey was conducted to grasp effects of drilling for structural boring in the geothermal survey on the peripheral environment. In the survey of animals, there were 5 orders/10 families/19 species of mammals and 10 orders/25 families/73 species of birds. Three kinds of precious animals were confirmed. There were 132 families/6,670 species in the flora. Three kinds of precious plants and three kinds of precious floras were confirmed. During the survey, drilling for structural boring was conducted. At three spas for survey, there were recognized some survey items of which there were great fluctuations. However, those are seasonal valuations or valuations related to the situation of the inside of hot springs. It is not recognized that the fluctuations were caused by the drilling work and pumping-up of geothermal water. The noise made during the well drilling was reduced around the well as theoretical values indicated. At a spot 200m away from the well, the noise was reduced from the environmental standard, and accordingly, it seems that there are few effects on the peripheral environment. The vibration was reduced around the well more than theoretical values indicated. That was below the control level at a spot 25m away from the well, and it seems that there are few effects on the peripheral environment. (NEDO)

  20. Fiscal 1999 international cooperation project report. R and D on convection control technology of glass melts by microgravity experiment; 1999 nendo bisho juryoku kankyo wo riyoshita glass yuekinai tairyu seigyo gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This R and D aims at development of convection simulation technology of glass melts based on measurement of accurate glass melt properties, and development of convection control technology of glass melts through the model experiment and small tank furnace experiment. Experiment was made on measurement of surface tension while levitating glass melts under the microgravity condition obtained by the drop tower of Japan Microgravity Center in Hokkaido. The shape of glass melt changes into a real sphere under the microgravity condition, and surface tension can be obtained by measuring its frequency, however, such frequency of glass could not be measured in this experiment. Levitation, fusion and oscillation experiment of glass was carried out by using an aero-acoustic levitator of CRT at Chicago. The experiment result is now in analysis. This study also aims the analysis in consideration of a surface tension flow effect. The calculation result showed generation of surface tension flow due to temperature gradient on a liquid surface. Various information were obtained through the model experiment using silicon oil, and glass convention observation by using a small tank furnace. (NEDO)

  1. FY 1998 geothermal development promotion survey. Report on the environmental effect survey (No. A-4 Kunbetsu-dake area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.A-4 Kunbetsudake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-30

    Of the FY 1998 geothermal development promotion survey, the primary environmental effect survey in the Kunbetsu-dake area was conducted, and the results were arranged. In the well drilling survey, etc., the survey was made aiming at extracting areas to be preserved from an environmental aspect. The results of the survey were summarized as follows: As to the mammalia, 12 families 46 species were confirmed in the area surveyed and the periphery by literature survey. Out of them, the noticeable species which are considered important from an academic viewpoint are 10 families 19 species. As to the aves, 55 families 340 species were confirmed, of which 29 families 79 species are noticeable species. About the amphibia/reptilia, 3 families 3 species in the amphibia and 4 families 6 species in the reptilia were confirmed by literature and hearing survey. The noticeable species is 1 family 1 species in the amphilia. Concerning the terrestrial insecta, 135 families 873 species were confirmed, and the noticeable species is 11 families 20 species. As to the flora, 115 families 1055 species were confirmed, and the noticeable species is 46 families 126 species. Relating to the living vegetation, the one higher than 9 in nature reserves shows a substantial rate, and the periphery of Kaibetsu-dake is designated as the specified flora colony. (NEDO)

  2. Research cooperation project for fiscal 1999. Research cooperation on environment-compatible type water resource effective utilization system; 1999 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made under this project to develop a wastewater treatment/regeneration system, easy to operate and maintain and low in cost, jointly with a Philippine research institute. Technologies are transferred to this institute concerning research and development, system designing, operation, maintenance, and management. The goal is to disseminate such technologies in the Philippines. As for fiscal 1999 endeavors, emphases are placed on the items described below. The Container Corporation which regenerates waste paper and the RAM Food Corporation which manufactures canned foods and pickles are selected as the sites for pilot plant research. Wastewater discharged by the two corporations is subjected to laboratory-scale wastewater treatment (combination of aerobic/anaerobic treatment and activated carbon adsorption), by which a pilot plant wastewater treatment process is determined and designing conditions are defined. As for activated carbon for advanced wastewater treatment, a fine grain sample, which is the lowest in price among activated coconut shell charcoals produced in the Philippines, is acquired, and tested for performance. A wastewater treatment pilot plant is complete at the Container Corporation, and has started operation. (NEDO)

  3. FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Study on possibility of research exchanges; 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo seika hokokusho. Kenkyu koryu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the study on possibility of research exchanges, conducted by Research Institute of Innovative Technology for the Earth (RITE) in FY 2000. For development of thin-film catalysts, HTE, a venture developing combinatorial chemistry application to catalysts, is a potential partner for the exchanges. One of the technical problems involved in underground sequestration of CO2 relates to evaluation of the reactions between CO2 injected under pressure and the surrounding rocks. It is a less site-specific theme, and preferably pursued through international networks. The RITE delegates have visited the British Geological Survey, Canada's Alberta Research Council, and US's Pennsylvania State University, Rice University and Chevron Petroleum, finding research exchange possibilities in all of these organizations for broad technical themes related to underground sequestration of CO2. For energy conversion technologies using biomass resources as the source materials, the potential partners for the research exchanges include Swedish Royal Institute of Technology, Belgium's Catholic University of Louvain and Spain's University of Zaragona which leads researches in production of gases from wastes and biomass. (NEDO)

  4. Survey on utilization of database for research and development of global environmental industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsu no tame no database nado no riyo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    To optimize networks and database systems for promotion of the industry technology development contributing to the solution of the global environmental problem, studies are made on reusable information resource and its utilization methods. As reusable information resource, there are external database and network system for researchers` information exchange and for computer use. The external database includes commercial database and academic database. As commercial database, 6 agents and 13 service systems are selected. As academic database, there are NACSIS-IR and the database which is connected with INTERNET in the U.S. These are used in connection with the UNIX academic research network called INTERNET. For connection with INTERNET, a commercial UNIX network service called IIJ which starts service in April 1993 can be used. However, personal computer communication network is used for the time being. 6 figs., 4 tabs.

  5. Survey on acceleration of geothermal development in fiscal 1998. Report on survey for influence on environment (No. B-7, Kuwanosawa district); 1998 nendo chinetsu kaihatsu sokushin chosa.Kankyo eikyo chosa hokokusho (No. B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    A survey was performed on the current situation in the Kuwanosawa district in Akita Prefecture to identify influence on the surrounding environment due to drilling of geothermal structure testing wells. The survey on animals covered mammals of five divisions, 10 families and 19 species, Aves of ten divisions, 25 families and 73 species, reptiles of one division, 3 families and 6 species, Amphibia of two divisions, 6 families, 9 species, and Insects of 17 divisions, 179 families and 719 species. Precious animals of a several species including black salamander were identified. In the plant survey, 132 families and 670 species were identified, with several species listed as the precious plants. In the survey of hot springs, those at three locations were all high-temperature hot springs at as high as 53.8 to 96.9 degrees C. Amount of discharge, pH and electrical conductivity differ largely by the hot springs. The hot spring in Takamatsu did not show large variation throughout the survey period. The Ogura Inn at Doroyu Spa has small variation in pH and hot spring temperature, but large variation in the amount of discharge and Al{sup 3+} concentration. Correlation was recognized between hot spring temperature and amount of discharge, between hot spring temperature and anion, between amount of discharge and electric conductivity, and between amount of discharge and anion. (NEDO)

  6. Investigational study of evaluation of the global energy system as a global environmental protection technology; Chikyu kankyo taisaku gijutsu toshite no global energy system no hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    With relation to some global energy systems of which viability is predicted in the future, an evaluation was conducted from the viewpoints of economical efficiency, energy balance, CO2 emission, etc. The fossil fuel CO2 capture system, the conventional thermal power plant added with CO2 recovery/treatment facilities, is expected to reduce approximately 70-75% of the CO2 emission. The fossil fuel decarbonated hydrogen system, which decarbonates fossil fuels, recovers/treats CO2 at the place of fuel supply and uses as hydrogen, is of poor practical application from an economical point of view. The fossil fuel methanol synthesis system, which synthesizes methanol from fossil fuels at the place of fuel supply, generates electric power and recovers/treats CO2 with the methanol, is large in energy loss and CO2 emission and low in overall efficiency and CO2 reduction effect at the time of methanol synthesis. The renewable energy hydrogen system is an ultimate system with no emission of CO2, though it costs much. 110 refs., 83 figs., 107 tabs.

  7. Characteristic analysis of methane-gas generation by oxidizing heat of stored coal and hold ventilation control; Sekitan unpansen ni okeru sanka hatsunetsu ni yoru methane gas hassei to sonai kankyo seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N; Nakashima, T [Kyushu Univ., Fukuoka (Japan); Kudo, S

    1999-12-31

    A demand of coal shows the tendency in the increase worldwide, with this, the marine transportation of the coal gradually increases, and the collier has also enlarged. The traffic pattern of coal is mainly the bulk transportation. In this transportation system, by the oxidation exothermic reaction of the coal, methane gas is produced, simultaneously the coal quality such as coking property or heat quantity is decreased and sometimes spontaneous ignition is caused. Therefore, it is necessary to equip with a ventilator to control the concentration of methane gas and to avoid the self heating of the coal. In this study, the quantity of methane-gas produced by heating coal using an electric furnace was measured and the experiment to investigate the temperature dependency of the methane-gas generated from the coal was conducted. By using the result of the measurement, the quantity of methane-gas produced from the coal stored in the hold of a coal cargo was estimated. And, the mathematical analyses on the changing degree depend on the times of a temperature in the hold under navigation, a concentration of oxygen and a concentration of methane-gas, were conducted. 11 refs., 19 figs., 2 tabs.

  8. Leading survey and research report for fiscal 1999. Survey and research on ozone-aided technology for creating comfortable environment; 1999 nendo ozone riyo kaiteki kankyo sozo gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to grasp the parts remaining technically unsolved of the ozone-aided technology for creating a comfortable environment, such as ozone-aided enhancement of the decomposition of nondegradable organic matters in the urban sewage and industrial wastewater. Efforts are also made to put in order and analyze data about the said technology, to isolate the current problems and the objects of technical deliberation for the future, and to examine the feasibility of the introduction of this technology. Case studies were conducted for a novel ozone-aided system and the effect is examined of the introduction of ozone-aided treatment into crowded towns, water supply systems, sewerage, and industries that handle paper and pulp, chemicals, electric power, and foods. Findings are mentioned below. The ozone utilizing technology when introduced improves the efficiency of water circulation, reduces pollutants at an excellent rate, suppresses the generation of carbon dioxide, and enhances safety of water resources and water environments. To realize such good results, however, it is important for the ozone to be high in concentration, for the accelerated oxidation and enhanced biofunction processes to be further studied, and for the system to be optimized. It is also found that a technology of appropriate ozone storage will help enhance cost reduction. (NEDO)

  9. Research and development achievement report for fiscal 1994 concerning the creation of advanced combustion technologies utilizing the microgravity environment; 1994 nendo bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The development committee concluded an agreement about on-site researches with NASA (National Aeronautics and Space Administration) for an international joint study, and the joint study was started at the underground microgravity center. Experiments were conducted at microgravity experimenting facilities and the data obtained were subjected to analysis and evaluation, which eventually contributed to the accumulation of useful data. In this fiscal year, microgravity experimenting facilities were utilized for experiments and tests for (1) the evaluation of the combustion and vaporization of fuel droplets and fuel droplet arrays, (2) analysis and evaluation of high-density fuel combustion characteristics, (3) evaluation of flammability limits, and (4) elucidation of the mechanism of the generation of NOx and the like. A total of 112 drop tests were conducted, and the acquired data were subjected to analysis and evaluation for the elucidation of the combustion mechanism, and findings were collected as mentioned below. Learned were the combustion behavior of fuel droplets such as ignition and flame propagation under item (1), combustion behavior such as ignition and combustion of high-density fuel under item (2), combustion behavior and combustion limits of premixed fuel under (3), and measurement of distribution of combustion products such as OH in the droplet fuel flaming zone under item (4). (NEDO)

  10. Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

  11. Investigations on a global environment improving technology utilizing biological functions. 2. Structuring a ligno-bioprocess; Seibutsu kino wo riyoshita chikyu kankyo kaizen gijutsu ni kansuru chosa. 2. Riguno bio process no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Discussions were given to reserve global environments on reducing dependence on fossil resources and more effectively utilizing wood resources. Economically utilizable amount of wastes from lumbering factories reaches about five million tons annually. Discussions were made on a ligno-bioprocess that uses these wastes. The current quantitative production efficiency of cellulase by means of bacterial breeding is very high. A problem is production of ligninolytic enzymes, to which application of the recombinant DNA method is indispensable. Combination of steam explosion with biological decomposition or the organosolv process is an effective method for lignin decomposition. Decomposition of cellulose by using the ultra critical water method is worth noticing. With respect to hemicellulose utilization, production of cellulose derivatives, biodegradable polymers and oligosaccharides would be conceivable by means of esterification and etherification. Vanillinic acid, adhesives, resins and lignin-based polymer materials could be manufactured from lignin. Material cost for these products accounts for about 35% of the product price, thus making the lignochemicals promising commercial products. 301 refs., 71 figs., 39 tabs.

  12. 'Nikkei Global Environment Technology Prize' awarded to the joint research group on regeneration of tropical forest; Nettairin saisei kyodo kenkyu ga 'Nikkei chikyu kankyo gijutsusho' wo jusho

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-11-10

    The tropical forest regeneration technology research group of Kansai Electric Power Company and Kansai Environment Center has been performing the research and development of tropical forest regeneration technology jointly with Indonesia since fiscal 1992. The group was awarded with the Global Environment Technology Prize from Nihon Keizai Shimbun, Inc. As a result of stringent examination on 97 applications, being two times as many as in usual years, the group received high evaluation on the originality, reality and possibility of proliferation of its research, and impacts given to the societies. Two other groups were also selected. The achievements were reported by the representative of the group in the award commemoration lecture at the global environment economist summit held by the Nikkei press the same day. Conventionally, afforestation done with considerable efforts has often been lost by forest fires and slash-and-burn farming, whereas the present research aims at establishing a comprehensive afforestation technology considering social and economic aspects, and CO2 fixation. As one of the choices of flexible measures as a result of the effect of forests having been recognized in COP3, frameworks for utilizing the mechanisms of joint implementation and clean resource development were introduced. Ever increasing expectations are placed on the achievements of the present research works. (NEDO)

  13. USW[center dot]33M-VS wind power turbine winning a 1993 environmental department prize of Discover Magazine. 1993 nendo DISCOVER kankyo bumonsho ni USW/33M-VS furyoku turbine

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, M. (Waseda University, Tokyo (Japan))

    1993-12-01

    This paper introduces a variable speed wind power turbine developed jointly by EPRI and US Wind Power Corporation. This wind power turbine has a wind velocity responsive construction in which generated alternating current power has the frequency vary with change in the shaft rotation speed. The specified performance calls for a cut-in of 4 m/s and cut-out of 29 m/s, wind velocity variable. The blades are made of laminated fiberglass, and the rotor has a diameter of 33 m, rotation variable. The tower height is classified to 24 m, 30 m, and 42 m. The blade pitch is controlled by a linear hydraulic cylinder, and the turbine is controlled by a microprocessor. The wind turbine has a system interconnecting control and data collecting system. Two induction three-phase generators are used. EPRI has calculated its power generation cost at 5 cents/kWh if wind blows at an annual average velocity of 16 miles per hour. This is nearly equivalent to the cost at new power plants. US Wind Power Corporation has disassembled 22 experimental models that have been in operation to investigate wear in the machines. Its economy is evaluated comparable with that for fossil fuel technologies. 1 fig.

  14. New energy visions for the Town of Naie district. Human-friendly Town of Naie City by environment-friendly energies; Naiemachi chiiki shin energy vision. Kankyo ni yasashii energy ga tsukuru hito ni yasashii machi Naie

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The new energy visions are drawn for Town of Naie, Sorachi-gun in Hokkaido, where the industrial sector (manufacturing industries) consumes more than 60% of the total energy consumption. By energy type, oil and others account for 80%. When arranged in the order of expected recoverable quantity, the new energies for the town include utilization of solar energy, photovoltaic power generation, wind power generation, and utilization of wastes, biomass energy (agricultural products) and snow energy. The basic guidelines for introduction of new energies are for health and welfare, clearing and utilization of snow, environmental education and bringing up talented persons, supporting the related entrepreneurs, and integration of new energy with promotion of energy-saving movement. The priority projects the town plans to promote include utilization of biogas and temperature-differential energy for the town's water purification center; foundation of the Naie eco-school; and drawing conceptions for utilization of underground heat, utilization of low-temperature and snow/ice energy, co-energy around the spa of Naie, and mega-solar and eco-park at the Sorachi housing complex. (NEDO)

  15. FY 2000 report on research and development of combustion technology utilizing microgravity conditions for fuel diversification; 2000 nendo bisho juryoku kankyo wo riyoshita nenryo tayoka nensho gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of optimum combustion technology with diversified fuels, e.g., naphtha and LCO, for gas turbines and others as power sources for topographical energy supply. The combustion under the microgravity is also investigated using the underground facilities at Japan Microgravity Center. Described herein are the FY 2000 results. For construction of combustion model and simulation, the combustion reactions for various liquid fuels are simplified to calculate ignition delay, adiabatic flame temperature and laminar burning velocity with an error less than about 3%. The microgravity combustion experiments are conducted for spray dispersed into a cylinder, to find flame propagation velocities changing with the vaporization characteristics of liquid fuels, and also to construct the combustion models. The premixed turbulent combustion simulation program is developed using a probability density function and analyzed. Development of new combustion technologies includes the study themes of flame propagation and combustion of the air mixture of the multi-component fuel in which the spray exists, combustion characteristics of the droplets of diversified fuels, and combustion of gas turbines with diversified fuels. A propane/air mixture shows different flame propagation characteristics whether it contains kerosene or LCO droplets. The effects of electrical field intensity in the combustion zone on combustion of fuel droplets are elucidated. (NEDO)

  16. Research report for fiscal 1998. Survey on the researchers and research institutes for the effects of global warming and its countermeasures; 1998 nendo onshitsu koka gas ni yoru kankyo eikyo nado ni kansuru kenkyusha kenkyu kikan chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researchers and research institutes across the world (except those in Japan), engaged in the study of global warming and measures to deal with the phenomenon, are extracted in compliance with certain specified standards, and the latest information on them is appropriately arranged and listed. It is further developed into an electronic database for the convenience of users. The collected information includes more than 230 research institutes and more than 1,000 researchers. The endeavor is exerted by extracting essays and institutes mainly out of the on-line databases. More than 1,000 essays and 130 institutes are covered. Visits are made to five institutes in the U.S. and four in Europe who are most actively engaged in the study of global warming, and detailed researches are conducted and information is exchanged. The Argonne National Institute copes with all energy problems related to global warming. Descriptions are given about environmental impact surveys and CO2 isolation in the ocean at the Center for Global Science of the Massachusetts Institute of Technology. At the Oak Ridge National Laboratory, the visitors heard explanations of technologies related to renewable energies and so forth. Researches are made into ecosystems at the University of California, and into natural energies at the University of Hawaii. Also visited are research institutes in Australia, Germany, Netherlands, and Britain. (NEDO)

  17. Fiscal 1998 research report. R and D on advanced combustion technology under microgravity environment; 1998 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on explication of a combustion phenomenon by using a microgravity facility, and a combustor possible to realize advanced combustion technology. In the basic research composed of 5 themes by the international joint research with NASA, 52 drop experiments using JAMIC's facility and 100 drop experiments using NASA's 2.2s drop tower were carried out. The themes are composed of an interaction in droplet arrays combustion, combustion of binary fuel sprays, combustion characteristics of solid fuel, flame dynamics around a lean flammability limit, and mass transfer around a combustion field. In the experiment using the microgravity experiment facility and analysis evaluation of the experimental data, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit, formation mechanism of NO{sub x} and an advanced combustor. For applying a pre-evaporating/pre- mixing combustion system to a combustor for aircraft engines, studies were made on some issues such as improvement of a combustion stability, NO{sub x} discharge characteristics, and optimum fuel atomizing. (NEDO)

  18. FY 1995 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1995 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This promotion project on the cooperative research aims to efficiently extract and recover valuable metals (gold, silver, copper, rare metal, etc.) including in large quantity in tailings of ores in the Republic of Kazakhstan. In FY 1995, conducted were the field survey, support study in Japan, acceptance of researchers from Kazakhstan, conceptual design of pilot plant, etc. The ore/mineral for Cu is mainly an alteration ore of chalcopyrite. Au and Ag are low grade and unknown, and the main gangue mineral is pyrite. The low grade ore (waste/much) of the Nikolayevska mine has a tendency to leaching at normal temperature, but the ore of mostly chalcopyrite such as tailings from each place has difficulty in leaching. It gets leaching by increasing temperature. The more the temperature rises, the more conspicuous the reaction becomes. Further, chalcopyrite is leached with priority over pyrite. From the result, a technical potentiality was obtained of leaching of low grade chalcopyrite in tailings mostly of pyrite. The existence of Thiobacillus ferrooxidans was confirmed. As to the recovery method for Au and Ag, CIC is studied. The process of waste/much is solvent extraction, electrowinning study and leaching, and that of tailings is bacteria leaching and leaching study. (NEDO)

  19. Fiscal 1994 survey report. Part 2. Study on soil environment remediation system using ecological information and functions; 1994 nendo seitaikei joho to seitaikei kino ni yoru dojo kankyo fukugen system no chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of the feasibility of soil environment remediation through detecting contamination of soil and changes in ecosystems caused by industrial activities, with attention paid to biological antagonists. In this fiscal year, based on the results of surveys conducted in the past, studies are continued mainly on hypersensitive biosensing technology using ecosystem functions, remote sensing technology to monitor the terrestrial vegetation and soil environment over wide areas, and soil environment remediation technology using biological antagonists and vegetation. In consideration of Europe's long experience in this field, seven organizations known for their accomplishments are visited, where interviews are held. There is a close relationship between soil environments and ecosystems, and ecosystems are provided not only with information on changes in soil environments but also with functions to remedy soil environments by minimizing secondary contamination. To put such information and functions to practical use, element technologies are indispensable, including hypersensitive soil environment biosensors and environmental remediation by identification and isolation of biological information carrying substances and by vegetation. Proposed in this report is a project for soil remediation by use of biological information and functions and for elucidation of biological antagonists. (NEDO)

  20. Investigations in fiscal 1983 on promotion of geothermal development. Part 1. Report on investigation of fumarolic environmental effects in Oku-Aizu area; 1983 nendo chinetsu kaihatsu sokushin chosa. 1. Okuaizu chiiki funkichu kankyo eikyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    As part of the investigations on promotion of geothermal development, surveys have been carried out in the Oku-Aizu area to identify the existence and/or extent of effects of collecting geothermal fluids above the ground imposed on the environment, such as the natural ecological system. The investigated area is an area of 60 km{sup 2} covering Kawanuma County and Onuma County in Fukushima Prefecture, a mountainous area with undulations. The investigation result may be summarized as follows: the area shows the inland climate and has snow fall as much as 2 m in winter; according to the H2S diffusion prediction, the concentration thereof on the land in seasonal average is 0.7 ppm at maximum, which is a value presenting no problems. No fumarolic effects of SO2 were identified, and floating dust and Hg showed values that present no problems. With regard to water quality during and after the blowout test, no effects of blowout return were identified. The noise level was 41 to 45 phones at a place 100 m distant, and the vibration level has become the lower detection limit at a place 50 m distant. Leveling has discovered no ground movement. No variation in major constituents in thermal spring water was verified before and after the blowout test. (NEDO)

  1. Fiscal 1995 survey report on the environmentally friendly type coal utilization system introduction support project. Verification project on the circulating fluidized bed boiler; Kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudosho boiler ni kakawaru jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    In relation to the circulating fluidized bed boiler which reduces the amount of sulfur oxides emitted in coal utilization, a verification project was carried out on installation of the equipment and spread activity in China and the Philippines contributing to the control of environmental pollutant associated with coal utilization and the effective use of energy. At the Fanshan area, installed was a 10t/h internal circulating fluidized bed boiler. At the performance test, coal includes around 7% of impurities such as stone, and the impurities should be excluded continuously at the time of actual run. Therefore, the boiler efficiency had to be changed from 89.5% to 85.8%. Further, power generation facilities have not yet been finished, and the overall operation of boiler turbine has not been executed. At the Zibo area, a 30t/h external circulating fluidized bed boiler was installed. The boiler efficiency reached 86.1%, over the targeted value. At the Batangas area in the Philippines, a 10t/h internal circulating fluidized bed boiler was installed. The boiler efficiency reached 85.8%, over the designed value. About the coal produced in the Philippines, slagging was feared, but the combustion state was favorable. 82 figs., 21 tabs.

  2. Life cycle assessment of supercharger for automotive use. Small displacement, high charging pressure engine and environmental load; Jidosha tosaiyo supercharger no life cycle assessment (LCA hyoka). Shohaikiryo kokakyu engine no kankyo eno yasashisa

    Energy Technology Data Exchange (ETDEWEB)

    Takabe, S; Sonoya, T; Hara, M [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1997-10-01

    In resent years environmental conservation requires low fuel consumption and low emission engine. And environmental load of every car life stage (production, using, abolition) is considered. Life Cycle Assessment of supercharging small displacement engine is reported, compared with natural aspirated engine as same maximum torque and maximum power as supercharging engine. 6 refs., 8 figs., 3 tabs.

  3. FY1995 high techniques of measuring for sensation, cognition arid behavior in the man-products-environment interface; 1995 nendo seihin kankyo interface ni okeru kankaku ninchi kodo keisoku kodoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    We measure the distribution of activation locus of brain cortex area and its time-sequence against various kinds of stimulus by using the fMRI that can visualize directly brain activities. Next, we try to make a simulation model of the information processing system of brain, and aim at establishment of new evaluation index for environment-human interface based objectively or quantitatively on brain activity data. we challenged to examining quantitatively brain activities by using functional MRI instrumentation technique. We made a effort to acquire functional MRI technique by repetition of pilot studies, and were successful in visualization of visual cortex (primary sensory area). In the latter period, sensory areas whose function had not been studied sufficiently and higher functional areas of brain which related to memory, attention and emotion were studied. The identification of action locus of gustatory area was tried using functional MRI studies. In studies about the ability of spatial attention, experiments elucidating locus participating in space perception and attention and its function were advanced. It was suggested that activation locus of brain was different between a color-form matched stimulus and a mismatched stimulus. The MRI measurement added the information of musculoskeletal system to the current analysis of human body configuration and gesture character, and a more detailed analysis of human body became possible. This is, an useful analysis was suggested by a plan of shoes pattern. (NEDO)

  4. Report on regional new energy vision for Kawara town. Toward the creation of eco-symbiotic community; Kawaracho chiiki shin energy vision hokokusho. Kankyo kyoseigata shakai no sozo ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A regional new energy vision has been formulated for Kawara town, Fukuoka Prefecture, in the hope that the industry, administration, and citizenry will be concerned with each other for the realization of an eco-symbiotic community. The fruits of endeavors exerted for this purpose are described in seven chapters, which are (1) the outline of surveys, (2) local characteristics of Kawara town, (3) policy toward introducing new energy, (4) measures for introducing new energy, (5) study of model projects, (6) introduction of new energy into Kawara town, and (7) efforts to realize the introduction. Described in chapter (5) are the introduction of photovoltaic power generation into primary and junior high schools, heat supply business utilizing waste heat from a plant, energy conservation at administration buildings, and the development of an activities program for people to learn energy related matters. Several applications are considered concerning the activities program, dependent upon who are to implement the program: volunteer students, local community leaders, experts, or administration officials. In relation to heat supply business, studies are conducted about the supply of waste heat from a cement plant to public facilities such as the town hall and administration buildings in the form of medium pressure steam or hot water. (NEDO)

  5. New energy vision for Kunigami village. Building a Village Friendly to the Environment in the 21st Century; Kunigamison shin energy vision. 21 seiki no shizen kankyo ni yasashii mura zukuri

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    A new energy vision has been formulated for Kunigami village, Okinawa Prefecture, for dealing with environmental problems and for activating the region through the utilization of new energy. It is a 6,000-strong village located at the northern end of the mainland of the Ryukyus, which consumed 35 GWh of electric power in fiscal 1998. The results of activities in this connection are summarized in seven chapters, which are (1) the current state of Kunigami village, (2) current state of new energy, (3) existing amount of new energy, (4) survey using questionnaires, (5) basic policy toward new energy introduction, (6) new energy vision formulation, and (7) a system for new energy introduction. Chapter (6) is constituted of the formulation of new energy projects and conditions to satisfy for their realization, with the projects covering the introduction of photovoltaic power generation, wind power generation, small scale hydroelectric power generation, and clean energy vehicles and the implementation of popularizing and enlightening activities. Under the project for popularizing and enlightening activities, information will be disseminated, people will receive education about environments, economic support will be provided, and support will be extended to enterprises for their beginning new energy businesses. The economic support to be provided will involve the introduction of the support systems of the Government and the study of the creation of a village operated support system. (NEDO)

  6. FY 1995 result report. Research/development on the creation of high-grade combustion technology using a microgravity environment; 1995 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report summarized the results of the research survey carried out by Japan Space Utilization Promotion Center (JSUP) under the contract with NEDO's industrial technology research and development department. This research survey is aimed at creating high-grade combustion technology which can respond to the decrease in environmental pollutant in combustion exhaust gas from viewpoints of energy diversification and global environmental preservation in consideration of the stabilized energy supply. Established inside JSUP is a research/development committee on high-grade combustion technology which is organized by men of learning and experience from universities, national institutes, private companies, etc. Following FY 1994, the following were continuously conducted: (1) joint research with NASA as an international research cooperation; (2) test using microgravity test facilities and analysis/evaluation of the test data. The experiment was conducted using facilities, etc. of the underground gravity-free test center established as a part of the national research base arrangement project. A lot of experimental data were obtained and stored which are useful for elucidation of the combustion mechanism and the development of ground combustor. (NEDO)

  7. International research cooperation in fiscal 1997. Report on the research, development, and evaluation of environmentally-friendly combustion technologies; Kokusai kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the research and development of environmentally-friendly combustion technologies that had been conducted for six years beginning in 1992, analysis and discussion were made by a special committee dedicated to the evaluation of the efforts, and the outcome is stated. In the study of zeolite-base catalysts, a highly active catalyst was developed which assumes a multilayer structure of mordenite, etc., with titanium introduced thereinto using an NO-selective reducing catalyst. As for metal complex oxide-base catalysts, various catalysts high in activity were developed, based on saponite which is a laminar, clayey compound. As for alumina-base catalysts, details were learned of the reaction mechanism and catalysis activation sites and, helped by the findings, a silver-supporting alumina catalyst was produced. In the study of direct decomposition type NOx removing catalysts, a success was achieved in causing NO to be decomposed with high selectivity in an oxygen atmosphere by use of new-type electrodes, functional layers, and solid electrolytes. In the field of catalytic combustion, a PdO-Pt/Ba-Al2O3 catalyst was developed, which is to serve for a hybrid type catalytic combustion method. 19 refs., 112 figs., 25 tabs.

  8. Report on survey for environment harmonizing type energy community project for Chubu International Airport. District heat supply facilities using large-scale cogeneration systems; Chubu kokusai kuko kankyo chowagata energy community jigyo chosa hokokusho. Daikibo cogeneration chiiki netsu kyokyu shisetsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The Chubu International Airport is positioned as a hub airport scheduled to start its use in the early part of the 21st century, to which introduction of large-scale cogeneration systems was discussed. Structuring an energy supply system conscious of the 21st century is intended, that is friendly to the environment, is attached with importance on the economy, and has high reliability and safety. The systems have cogeneration capacity from 4,500 to 6,000 kW, and utilize high-pressure waste heat from the cogeneration system as the heat source. The system uses the high pressure waste heat, stored heat, and gas at the same time to achieve high economic performance brought about by heat storage and the best energy source mix, while attempting cascade utilization of the heat. Considerations were given to suppress the environmental and energy load on the district as low as possible for the coexistence with the district, and to build framework and coordination to return the merits to the district. Subsidy introduction also has a great effect to assure the economic performance. The optimal specific construction of the system was found in combining the utilization of energy generated from temperature difference in sea water as a heat source system, the topping system utilizing the high pressure waste heat available in the system, high-efficiency heat pumps, and the heat storing system utilizing electric power available at late night. (NEDO)

  9. New energy vision of the Tagawa city area. Aiming at a town for symbiosis of humans and the environment; 2001 nendo Tagawa shi chiiki shin energy vision. Hito to kankyo ga kyoseisuru machi wo mezashite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Tagawa City, Fukuoka Prefecture, an investigational study was conducted of the energy supply/demand of the city, existence amount of new energy, project for new energy introduction, etc., and a vision was worked out. The energy consumption amount of the city was estimated at 6,678,932 GJ/y. It consisted of 42% in the industrial sector, 35% in the transportation sector and 23% in the commercial/residential sector. The rate of energy source was 75% of petroleum-base energy and 25% of electric power. As the project for new energy introduction, the following were studied: power generation/thermal exchange/composting by fermentation of methane from stockbreeding waste; environmental preservation type agriculture such as large-scale hothouse using exhaust heat from cement plant; utilization of ground mine water at coal goaf for space cooling and as water source; introduction of photovoltaic power generation/solar energy use hot water supply system to public facilities; introduction of clean energy car to vehicle in welfare/education fields; preparation of a program for energy environment education; preparation of bases for energy environment education. (NEDO)

  10. Report for fiscal 1998. Joint research of environment-friendly system for effectively utilizing water resources; 1998 nendo hokokusho. Kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research is conducted in cooperation with Industrial Technology Development Institute of the Philippines, and aims to solve water related problems such as unstable water supply and water quality pollution though developing a waste water treatment and recycling system which is easy to operate and maintain, low in cost, and usable in the Philippines. Fiscal 1998 is the second year of the project. Statistics are studied about the load that each industrial branch imposes on water for its pollution, and it is found that food manufacturers, paper pulp mills, and fiber dyeing plants are heavily responsible for water pollution. A method consisting of single-tower UASB anaerobic treatment and activated sludge treatment is applied as a water treatment process to Ram Food Products Corporation, and its optimization is studied. A removal rate 60% is achieved after a 12-hour treatment period at a COD (chemical oxygen demand) rate of 8g/liter/day. A method consisting of coagulating sedimentation and activated sludge treatment is applied to the waste water from a Solid Mill Corporation dyeing plant, when it is found that the water after ultimate treatment is almost colorless and that COD is 76mg/liter and BOD (biological oxygen demand) 13mg/liter, and these suggest that the waste water is recyclable. Since it is low in COD removing rate, the application of anaerobic treatment to high-concentration water after washing is not appropriate. (NEDO)

  11. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

  12. Report on the achievements in fiscal 1999. Surveys on the foundation for establishing industrial technology strategies (Foundation and environment improving strategies - an overall survey); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kiban kankyo seibi senryaku (zentai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were performed on the foundation for technological innovation in Japan and other countries. Main findings obtained from the actual state survey were compiled from the two aspects of 'items having difference in international comparison' and 'main findings by nucleuses and functions'. In order to activate the economy stagnated in the 1980's, America has developed strong industrial technology policies under the initiative of the government to strengthen the competitive edge, and the result thereof appears linking with the briskness in the today's U.S. economy. In Japan, the non-competitive fund distributed uniformly to national universities and national research institutes accounts for the majority in the governmental research fund. In contrast, many of the research funds of the U.S. government are the competitive fund, whereas researchers perform their research works using these funds, including their own labor cost, and the competition is intense. America is regarded to have put a huge amount of national defense research expense and space development research expense into private business entities, which are playing a large role in developing advanced technologies. A great amount of governmental fund is injected concentratedly into researches of health, medical and bio-technologies. (NEDO)

  13. FY1998 Report of surveys on network possibility involved with proliferation and transfer of environmental technologies (Europe, Australia and New Zealand); 1998 nendo kankyo gijutsu no fukyu iten ni kakawaru network kanosei chosa hokokusho . Oshu Goshu New Zealand

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    At the third Conference of the Parties to the United Nations Framework Convention for Climate Change (COP3) held in December 1997, the industrialized nations have agreed on development and proliferation of innovative technologies under international cooperation and transfer of environmental technologies to developing countries by expanding and strengthening CTI being the framework to be progressed spontaneously. Under the international strategic research project for global environment, NEDO has been promoting positively the research and development, whose support is urged to be expanded further in the future upon receiving the present agreement. Therefore, NEDO has performed the present survey in order to propose frameworks and measures for strengthening and expanding CTI. From among the policies and measures to be taken by the related countries based on the COP3 protocol, fiscal 1997 has performed review and new establishment of plans involved with execution of the items related to technology development, and surveys on action movements such as review and expansion of the measures, as the first stage. Fiscal 1998 has executed surveys focusing on the network for technology proliferation and transfer to developing countries as the second stage. (NEDO)

  14. Fiscal 1996 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1996 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The research was conducted jointly with Europe of a catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. Reformation of mordenite and {beta}-zeolite was done by ion exchange, ion implantation, and membrane formation. A catalyst was searched for to obtain reducing agents, C5-C8 components, by decomposing light oil. Saponite, clay compound, showed by copper and silver ion exchanges approximately 50% of activity under 20,000h{sup -1}, C3H6 reducing agent, and without steam. The effect of the temperature of sintering on NOx selective reductionality of silver-carrying alumina catalyst was studied, and in sintering at 800degC, activity increased. When using conductive oxides like ruthenium oxide for electrolyte, NO decomposition selectivity increased. As to the functional layer carried above the Pd electrolyte, iron oxide and magnesium oxide increased NO decomposition selectivity. PdO and rare earth oxides forming compounds controlled variation of activity by dissociation/reoxidation of PdO. As to PdO/Gd203, the initial methane combustion activity was favorable, but there was seen deterioration with age. 271 refs., 281 figs., 58 tabs.

  15. Report on the achievements in fiscal 1999. Surveys on the foundation for establishing industrial technology strategies (Foundation and environment improving strategies - an overall survey); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kiban kankyo seibi senryaku (zentai chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys were performed on the foundation for technological innovation in Japan and other countries. Main findings obtained from the actual state survey were compiled from the two aspects of 'items having difference in international comparison' and 'main findings by nucleuses and functions'. In order to activate the economy stagnated in the 1980's, America has developed strong industrial technology policies under the initiative of the government to strengthen the competitive edge, and the result thereof appears linking with the briskness in the today's U.S. economy. In Japan, the non-competitive fund distributed uniformly to national universities and national research institutes accounts for the majority in the governmental research fund. In contrast, many of the research funds of the U.S. government are the competitive fund, whereas researchers perform their research works using these funds, including their own labor cost, and the competition is intense. America is regarded to have put a huge amount of national defense research expense and space development research expense into private business entities, which are playing a large role in developing advanced technologies. A great amount of governmental fund is injected concentratedly into researches of health, medical and bio-technologies. (NEDO)

  16. Promotional operation for developing industrial technologies for global environment in fiscal 1998. International research exchange operation; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective of creating a new scope of study intended of solving global environment problems and structuring a new technical system, exchanges with overseas researchers and research institutions have been carried out subsequent to those in last year. In fiscal 1998, six researchers from different countries were invited to implement joint researches, and two overseas researchers were invited to an international conference on industrial technologies for global environment. In addition, in order to identify trends of research and development in overseas countries, two researchers were sent to universities in Germany and the U.S.A., and three researchers to international conferences and symposiums on the industrial technologies for global environment. It was intended to exchange technological information between overseas researchers and Japanese researchers who are performing the advanced researches on the industrial technologies for global environment, and to proliferate the latest items of technological information. Therefore, seven international seminars have been held, including the '98 Japan-China Global Environment Protection Symposium, 'substance migration and carbon circulation in coral reefs', 'plant bio-technologies in the 21st century', and the Fourth International Forum for Environmental Catalysts. (NEDO)

  17. Catalytic technology in the energy/environment field. Utilization of catalyst in coal pyrolysis and gasification processes; Energy kankyo bun`ya ni okeru shokubai gijutsu. Sekitan no netsubunkai oyobi gas ka ni okeru shokubai no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, Y. [Tohoku University, Institute for Chemical Reaction Science (Japan)

    1998-05-20

    This review article focuses on the utilization of several catalysts during coal pyrolysis and gasification. In situ or off line catalytic upgrading of volatile matters during pyrolysis of low rank coals is carried out in pressurized H2 with different reactors to produce BTX (benzene, toluene and xylene). When NiSO4 and Ni(OH)2 are used in the hydropyrolysis of Australian brown coal using an entrained bed reactor with two separated reaction zones, BTX yield reaches 18-23%. MS-13X zeolite and USY zeolite mixed with Al2O3 are effective for producing BTX with powder-particle fluidized bed and two-stage reactors, respectively. Catalytic gasification is described from a standpoint of direct production of SNG(CH4) from coal and steam. When K2CO3 and Ni are compared for this purpose, Ni catalyst is more suitable at low temperatures of 500-600degC, where CH4 formation is thermodynamically favorable. Fe and Ca catalysts can successfully be prepared from inexpensive raw materials and are rather active for steam gasification at {>=}700degC. The use of upgrading and gasification catalysts is discussed in terms of preparation, performance, life and recovery. 27 refs., 6 figs., 2 tabs.

  18. Fiscal 1995 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1995 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research and development were conducted jointly with Europe of an environmental harmony type high efficient catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. In the research and development of NOx removal catalyst such as zeolite base, reformation of mostly mordenite was done by ion exchange, ion implantation, skeleton element substitution, etc. A possibility was found out of applying the membrane formation method except ion implantation as reforming means. In the R and D of the complex oxide base NOx removal catalyst, it was found that the catalyst carrying copper and silver on silica and layer clay compound under optimum conditions shows peculiarly high activity, and there is little decrease in the activity, but rather increase in it even under vapor existence. An evaluation was made of NO resolution of direct resolution element carrying noble metal electrolyte on solid electrolyte, finding out that the highest NO selectivity is shown with Pd as electrolyte and at a baking temperature of about 1300degC. Development of high- and low-temperature catalysts was also made. 417 refs., 286 figs., 63 tabs.

  19. FY 1999 report on the results of the R and D of the environmentally friendly type production technology - high functional chemical synthesis bioreactor; 1999 nendo kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were carried out of 'high functional chemical synthesis bioreactor' which makes use of the reaction mechanism of the living organism composed under normal temperature/normal pressure, and the FY 1999 results were summed up. In the development of the element technology to control appearance of bacteria and animal cells, a reactor assessment system to produce the combined transferrin was constructed using the recombined cells which were bred by introducing the integrated vector. By this assessment system, the target value of material productivity was achieved. As to the multiple stage enzyme reaction control breeding technology, the colon bacillus into which 6 kinds of genes in relation to the reaction from hydroxypyruvaldehyde dehydrogenase to cysteine were integrated was incubated, and the appearance of all the enzymes was achieved. In the technology development of a bioreactor system, the production of 1 unit/mg protein of enzyme in 24 hours was achieved using the continuous two step incubation system. Further, to assess the material productivity of the recombined colibacillus, study of conditions of cysteine production was made using the fixed fungus body, and cysteine productivity of 11.3g/l was successfully achieved. (NEDO)

  20. FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. For safety and environmental factors; 2000 nendo jidoshayo nenryo denchi no fukyu kiban seibi seika hokokusho. Anzensei shuhen kankyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the FY 2000 activities for safety and environmental factors involved in fuel cell powdered vehicles. The current technical standards and specifications for CNG and LPG fueled vehicles are investigated, to extract the factors necessary to establish the safety evaluation guidelines when these fuels are replaced by hydrogen fuel. The rules extracted and studied include those related to collision and resultant fuel leakage, removal of spark and hot sources, leakage in the fuel system, leakage into containers and passenger rooms, and materials. For the rules on test methods of fuel tanks, the investigated items include fire resistance, impact resistance and permeation loss of fuel from the tanks. For system safety, the investigated items include possible unusual situations, leakage of the electrolytes and electrical shock. The basic data are collected for destruction of the fuel tanks, spout of hydrogen from and electrification of the hydrogen-occluding alloys, flame retardancy of high-voltage wires for automobiles, and hydrogen diffusion simulation. The safety-related technical trends are followed by hearing the related organizations, including automakers. Literature survey and hearing are conducted to investigate the environmental effects of radio wave interference and noise. (NEDO)

  1. Reduction of energy essential to human life by 70%. Environment-friendly residence `ED-1` utilizing the sunlight effectively; Seikatsu ni hitsuyona energy no 70% sakugen. Taiyoko riyo no kankyo kyosei jutaku ED-1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    This paper presents the environment-friendly residence `ED-1` utilizing the sunlight effectively. ED-1 of 97m{sup 2} in first floor area and 81m{sup 2} in second one has, on its roof, the photovoltaic power generation system, the solar hot water collector which supplies hot water by circulating heated antifreezing solution into a hot storage tank, and the solar hot wind collector which largely contributes to energy saving together with a hot room named an S unit on the first floor. The small S unit faced toward the south adjacent to a dining room is made of timber and thermal insulation glass. The S unit stores heat in a floor by taking the sunlight into a room in winter, while enhances a heating effect by discharging stored heat in nighttime. In some cases, duct circulation of heated wind is possible. Solar radiation of 90% can be removed by outside glass fiber screen of the S unit together with double glazing coated by special metal film. Roof material is superior in heat insulation, air tightness and energy saving, while floor material in sound insulation and heat storage. The target for reducing energy essential to human life by 70% was thus nearly achieved. 1 fig.

  2. Energy and power source mix in East Asia. Restrictions on resource, fund and environment and the future prospect; Higashi Asia no energy dengen mix. Shigen shikin kankyo no seiyaku to kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    In Asian countries, the economic growth rate is extremely higher as compared with the world average, and accordingly a large growth in energy supply/demand and electric power supply/demand is paid attention to. Besides, at users` side, a fear is the worsening of the environmental problem which is brought about by a rapid increase in energy consumption. At suppliers` side, introduction/expansion of a large amount of foreign funds for rapid promotion of power source development become necessary so that supplying facilities catch up with the growth in demand. Moreover, dependence of the supply upon outside the area is becoming higher, and problems in safety guarantee are also becoming prominent. As for energy/power source mix in East Asian countries, the stable supply is basically considered as most important, and economical efficiency is also important including competition conditions among energies and potential raising of investment in supplying facilities. It is no exaggeration to say that the increase in the rate of coal which occupies most of the primary energy supply/power source in East Asian countries depends upon the progress of environmental harmony technology such as clean coal technology. 39 figs., 132 tabs.

  3. FY1996 research cooperation for the development of the environmentally friendly technology for highly efficient mineral resources extraction and treatment; 1997 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The above-named project aims to jointly develop technologies to efficiently extract and recover valuable metals (gold, silver, copper, rare metals, etc.) from slag, with caution fully exercised to conserve the environment, for effectively utilizing non-ferrous resources in the Republic of Kazakhstan. The effort covers a seven-year period beginning in fiscal 1994. The elements which are studied are technologies that involve leaching, solvent extraction, electroextraction, recovery of gold and silver, and waste water treatment. In this fiscal year, wet treatment, gold and silver treatment, and waste water treatment are studied in on-site joint researches and in domestic researches for specimens sampled at the Kazakhstan site. In addition, based on the results of the above-said basic researches, some parts of the pilot plant to be constructed is designed and manufactured. For propelling forward the project, equipment necessary for joint research is procured and forwarded to the site, and Kazakhstan scientists are invited to Japan for training. (NEDO)

  4. Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

  5. Adaptability of drowsiness level detection that measures blinks utilizing image processing to changes in the ambient light; Hikari kankyo no henka ni tekiosuru kao gazo shori ni yoru inemuri unten kenchi

    Energy Technology Data Exchange (ETDEWEB)

    Kaneda, M; Obara, H; Nasu, T [Nissan Motor Co. Ltd, Tokyo (Japan)

    1997-10-01

    A drowsiness warning system that measures blinks utilizing image processing technology has a number of issues that need to be resolved. One issue is the adaptability of the system to changes in the ambient light environment in the actual vehicle interior. We have devised image processing software which is robust to changes in the ambient light. The drowsiness detection performance of the system was evaluated in laboratory tests and actual driving tests. It was found that the system can has a positive effect on detecting drowsiness level. 3 refs., 10 figs.

  6. Fiscal 1990 technological survey report. Report on NEDO's 10th anniversary international symposium (New energy and global environment); NEDO soritsu 10 shunen kinen kokusai symposium hokokusho. Shin energy to chikyu kankyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-10-03

    Two lectures were given by Christopher Flavin (vice president for Research, Worldwatch Institute Inc.) and Hiroshi Takeuchi (chairman, LTCB Consulting and Research Institute Inc.), and a panel discussion was held by five panelists with Toyoaki Ikuta (The Institute of Energy Economics, Japan) as the coordinator. The themes were 'a sustainable energy strategy for the nineties', 'industrial structure change and energy problem', and 'new energy and the global environment'. The panelists were from Sweden, France, Thailand, U.S.A., and Japan. The main subject was energy security, in which discussion was held on the uneven distribution of oil resources in the Middle East and political instability in the region and on counter measures against global warming problem. The discussion on the latter subject showed that a limitation exists in the total consumption of fossil fuel in the world, and that energy policies were meaningless unless they were on a global scale. As the concrete measures, energy conservation technologies and regenerative energy utilization technologies need to be developed and spread, for which emphasized was the spread on a global scale, namely, the necessity of international cooperation and an international propulsion system. (NEDO)

  7. Research on the establishment of the database system for R and D on the innovative technology for the earth; Chikyu kankyo sangyo gijutsu kenkyu kaihatsuyo database system ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of structuring a database system of technical information about the earth environmental issues, the `database system for R and D of the earth environmental industrial technology` was operationally evaluated, and study was made to open it and structure a prototype of database. In the present state as pointed out in the operational evaluation, the utilization frequency is not heightened due to lack of UNIX experience, absence of system managers and shortage of utilizable articles listed, so that the renewal of database does not ideally progress. Therefore, study was then made to introduce tools utilizable by the initiators and open the information access terminal to the researchers at headquarters utilizing the internet. In order for the earth environment-related researchers to easily obtain the information, a database was prototypically structured to support the research exchange. Tasks were made clear to be taken for selecting the fields of research and compiling common thesauri in Japanese, Western and other languages. 28 figs., 16 tabs.

  8. Investigation on construction of the database system for research and development of the global environment industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsuyo database system no kochiku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This paper studies a concrete plan to introduce a new database system of Research Institute of Innovative Technology for the Earth (RITE) which is necessary to promote the industrial technology development contributing to solution of the global environmental problem. Specifications for system introduction are about maker selection, operation system, detailed schedule for introduction, etc. RITE inhouse database has problems on its operation system and its maintenance cost, and is apt to be high in a construction cost in comparison with a utilization factor. Further study is made on its introduction. Information provided by the inhouse database is only the one owned by the organization, and information outside the organization is provided by the external database. The information is registered and selected by the registerer himself. The access network is set by personal computer network at the beginning and is set to transit to INTERNET in the future. For practical construction of the system, it is necessary to make user`s detailed needs clear for the system design and to adjust functions between hardware systems. 32 figs., 9 tabs.

  9. FY 1997 report on the research for construction of NEDO`s vision. Regional environment and international collaboration; 1997 nendo chosa hokokusho (NEDO vision sakutei ni muketa chosa kenkyu). Chiiki kankyo to kokusai kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is necessary for NEDO to transfer the energy technology to developing countries and conduct collaborations with them efficiently. First of all, environments of the community were analyzed from a viewpoint of natural environment, social and cultural environment, and industrial and economic environment. Then, this report outlines the organizations of domestic and international aid agencies which have potentials to conduct alliance and collaboration with NEDO, and also illustrates their activities including financing and technology exchange, regional activities, and progress of activities. Alliances and collaborations with NGOs of each international organization were analyzed on the aspect of the fields and know-how of alliance with NGOs, selection standards of NGOs and necessary systems and organizations to make effective alliance and collaboration with NGOs, and some case studies were taken. Organization, purposes and activities of NGOs in Asian countries are introduced, and their current situations are illustrated. Finally, some proposals were offered to make alliances and collaborations with aid agencies and NGOs. They are concerned about the fields and know-how of alliance with NGOs, selection standards of NGOs and necessary systems and organizations to make effective alliance and collaboration with NGOs. 44 figs., 8 tabs.

  10. Fiscal 1997 report on the survey of effects of enhancement of energy consumption efficiency on the global environment; 1997 nendo chosa hokokusho (energy shohi koritsuka chikyu kankyo eikyo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper surveyed the state of studying the measures against global warming in the third assessment report of the Intergovernmental Panel on Climate Change (IPCC) and made analyses of the trends of preventive measures for global warming in other countries, aiming at presenting data for studying the future enhancement of energy consumption efficiency in the Asia Pacific region. In the U.S., a report was taken up from Executive Office of the President which is entitled `the federal government R and D of energy for solution to problems in the 21st century.` The report made analyses of the federal government R and D of energy and at the same time recommended an increase in R and D budget and reinforcement of the organization of the Department of Energy. In Europe, the carbon tax, CO2 tax, energy tax, etc. are introduced or studied for reduction of CO2 emissions. OECD made public a report approved in May 1997 which is entitled `the environmental tax and green tax reform.` Also studied were the introduction and effects of the carbon tax aiming at reducing CO2 emissions in developing countries. More attention is being paid to economic effects predicted in case developed countries reinforce various kinds of measures for targeted reduction of greenhouse gases. 2 figs., 4 tabs.

  11. Research program for environmentally-friendly coal utilization system. Follow-up project for simplified desulfurizers (Weifang Chemical Industry Works); Kankyo chowagata sekitan riyo system donyu shien jigyo. Kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakosho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To suppress the emission of environmental pollutants from coal utilization in China and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into China have been promoted. Demonstration program for diffusing simplified desulfurizers has been promoted. For accelerating the achievement, experts of desulfurizers were delegated to Weifang Chemical Industry Works, to support the program. Exhaust gas is introduced from boiler via water spray dust remover, suction fan and centralized stack into absorption tower of the simplified wet-type desulfurizer. In the ascending process, the exhaust gas contacts with absorbent, to remove SO2 and dust. The absorbent is blasted up through the spray nozzle. The absorbent is oxidized by the air into sulfate ion in the liquid chamber at the lower part of tower, and neutralized by hydrated lime to form gypsum. Through the continuous operation for two years, understandings were remarkably increased. However, good treatment of the tax system is required for further diffusion. Though there are no problems for ordinary start and stop, emergency operation is insufficient. There are some problems in the maintenance due to the delay of finding failures. 16 figs., 1 tab.

  12. Environmental science, petroleum engineer`s view. CO2 gas reduction technologies for global warming prevention; Sekiyu gijutsusha no shiten kara no kankyo kagaku. Chikyu ondanka eno taio no tame no CO{sub 2} yokusei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nomura, K [Tokyo (Japan)

    1998-08-01

    This paper discusses the techniques concerning diesel engines for cogeneration systems, techniques concerning fuel consumption-saving type lubricating oils and techniques concerning oil refineries, out of the CO2 emission control (energy saving) techniques for coping with the global warming which the petroleum engineers are now tackling. The paper introduces CO2 emission control techniques using a petroleum cogeneration system and studies on NOx removing techniques using catalysts as the techniques concerning diesel engines; techniques for reducing friction loss, which occurs in an engine and a transmission, by improving the recipes of lubricating oils and the development of novel friction modifiers as the fuel consumption-saving type lubricating oil techniques; and the CO2 separating techniques using a system for recovering the low-temperature waste heat produced in petroleum refinement with a high efficiency, or using a solid film such as a molecular sieve as the energy-saving techniques used in oil refineries. 18 refs., 8 figs., 1 tab.

  13. Fiscal 2000 achievement report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; 2000 nendo hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research aims to develop materials and apparatuses for the purification of atmosphere using titanium dioxide that exhibits a powerful oxidizing capability when irradiated with light. A study is conducted to find out an optimum composition for a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is found to show high denitration efficiency, and this achieves the denitration efficiency goal. As for sheet thickness, 0.75mm is found to be enough. The sheet experiences some hardening in an accelerated exposure test, but does not change much in a surface gloss test or a chalking test. Although a slight reduction is observed in denitration efficiency, yet the durability goal is achieved. In the effort to develop an energy conservation type air cleaning apparatus, field tests and experiments are repeatedly conducted. As for photodenitration in the cleaning apparatus, the number of photodenitration stages and the magnitude of equimolar adsorption area necessary for achieving an 80% denitration rate is calculated from the relations of the NOx concentration profile and the denitration rate in the equimolar adsorption module to (gas flow rate/module surface), and the result shows that the initially intended goal is achieved. (NEDO)

  14. FY 1996 result report. Research/development on the creation of high-grade combustion technology using a microgravity environment; 1996 nendo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    With the aim of creating high-grade combustion technology which can respond to the decrease in environmental pollutant in combustion exhaust gas, the high-grade combustion technology research development committee was established inside JSUP (Japan Space Utilization Promotion Center), using the underground gravity-free test center. Following FY 1995, the following were conducted: (1) international joint research with NASA, and (2) tests using microgravity test facilities, etc. and analysis/evaluation of the test data. As to the international joint research, a lot of new information was obtained through the adjustment conference with NASA. Further, there were a lot of results obtained from joint tests and researches. Moreover, the leading experimental device and measuring device which are usable in the microgravity field were developed/prepared. Conducted were combustion/evaporation evaluation experiments on fuel droplet and groups of droplet, combustion characteristics elucidation evaluation experiments on high-density fuels, evaluation experiment on flammability limits, and elucidation evaluation experiments on emission mechanism of NOx, etc. Through those, abundant experimental data were able to be accumulated, and a lot of precious knowledge/information were obtained. Besides, the fabrication of high-class combustor test equipment for ground demonstration was started. (NEDO)

  15. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system. Potential survey of the spread of high efficiency coal boiler; 1999 nendo kankyo chowa gata sekitan system kanosei chosa. Kokoritsu sekitan boira fukyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the coal consumption amount and reducing the emission amount of environmental pollutants, study of small stoker boilers in China was made in terms of sampling of the data on changes in boiler efficiency caused by combustion conditions and how to improve efficiency. As objects of survey, one boiler use plant in Beijing city and two in Taiyuan city, Shanxi province, were selected to make site survey on the state of installation and operational management of coal boiler. As a result of the actual measurement of boiler efficiency at the plants, the boiler efficiency was the maximum, about 76%, in Beijing city and the minimum, about 51%, in Taiyuan city. In China, the number of boiler with the Beijing city level was extremely small, and most of the boilers were the same as the Taiyuan city level. As a result of studying how to improve efficiency based on the survey results, the following were cited as the main measures for improvement: selection of coal by boiler type and supply of the secondary air, strengthening of the combustion management by controlling furnace pressure and air amount, etc. For the selection of coal, it is necessary to set up a system to be supported by the whole country or the whole department. (NEDO)

  16. Survey report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Dispatch of engineers; 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (senmonka haken)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this survey is to improve the coal utilization technology and to contribute to the environmental protection. Through long-term dispatch of experts for the coal utilization technology, coal utilization facilities are surveyed at the sites, advises for coal utilization technology and environmental protection technology are given, and useful information for the cooperation with the partner country are exchanged. In this fiscal year, experts were dispatched to Thailand in addition to China, to conduct cooperative surveys, technical exchanges and seminars with both countries. Experts for desulfurization technology, circulating fluidized bed boilers, effective coal ash utilization technology, and coal preparation technology were dispatched to various places in China. Among various model projects conducted in China, examples of model projects for simplified desulfurizer introduction, circulating fluidized bed boiler introduction, and briquette production facility introduction were presented at seminars held at two cities in China. Experts for briquette production technology and circulating fluidized bed boiler technology were dispatched to Thailand, to conduct cooperative surveys and technical exchanges. 22 figs., 9 tabs.

  17. Research cooperation project for fiscal 1998. Research cooperation on the research and development of environment measuring laser radar (Follow-up); 1998 nendo kankyo keisokuyo laser reda no kenkyu kaihatsu ni kansuru kenkyu kyoryoku. Flow up

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development of laser radars for observing urban atmospheric pollution is jointly conducted by Japan and Indonesia for the goal of contributing to the construction of an administrative system on environmental matters compatible with the actualities of Indonesia. Under this project, laser radars are installed at three sites in the city of Djakarta where environmental problems are increasingly serious, an observation network system is constructed connecting the laser radar sites, and the data are collected, analyzed, and processed by a data processing center. This enables the acquisition of information about the pollution of urban atmosphere through the observation of the 3-dimensional distribution of atmospheric pollution. In fiscal 1998, the last year for follow-up, engineers and researches are dispatched by 'ODA (official development assistance) laser radar observation assistance committee' for assistance in system maintenance and pollution observation. System maintenance is carried out so that the laser radar system may be utilized by the Indonesian party. Observation assistance involves Mie scattering, and the Indonesian party is engaged in a long-term continuous laser radar observation. (NEDO)

  18. Fiscal 2000 achievement report. Development of comprehensive technologies for environmental conservation including prevention of global warming by the carbonization of wood, etc.; 2000 nendo jumoku nado no tanka ni yoru ondanka boshinado fukugo kankyo taisaku gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are exerted to develop new technologies whereby carbon dioxide is absorbed by and fixed in rapidly growing trees. The trees are felled and subjected to high-efficiency carbonization, and the thus-obtained carbonized material is used for environmental purification or the like and then buried in the ground. Studies are under way to find out if the cycle (operations) may be organized into an industry. Activities are conducted in the five fields of (1) carbonized materials, (2) carbonization, (3), industrial use of charcoal, (4) stabilization of charcoal, and (5) reports on surveys (mainly overseas). In field (2), following an introduction consisting of the carbonization mechanism and the definition of terms, surveys are conducted of the existence of carbonizable resources in Japan, distribution channels of imported charcoal and activated charcoal in Japan, various carbonization apparatuses, carbonization equipment incorporated into gasifying fusion furnaces, carbonization furnace as a system, and the trends of development of pyroligneous acid and development of its use. In field (3), studies are made on its use in industries, on its application to agriculture, forestry, and livestock industry, and on the utilization of its electromagnetic properties. (NEDO)

  19. Report on fiscal 1995 project to promote an exchange of researchers on environmental problems in the Asia-Pacific region; 1995 nendo itakujigyo (Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of solving environmental problems caused in association with the increasing industrial activities in the Asia-Pacific region, the construction of a research network is being advanced aiming at promoting exchanges with researchers of other countries and activating information exchanges. Investigators were sent overseas to grasp the present situation, and researchers participated in a symposium on the APEC environmental technology cooperation for mutual understanding and personal interchange. In the overseas survey, visits were paid mainly to national research institutes and universities in India and Thailand. Positive approval was obtained on the construction of the ETERNET APR (Environmental Technology Research Network in the Asia-Pacific Region). In the symposium on the APEC environmental technology cooperation held in Nagoya, researchers participated mostly in the second session and made earnest discussions with researchers from other countries. The necessity and importance of the network was emphasized. Countries which participated the symposium have problems common to each, and it was greatly significant to meet together and discuss together. The environmental problem is on a global scale, and it is necessary to make close exchange/interchange of information/opinion on a long term basis and to tackle it in the whole Asia-Pacific region. 3 tabs.

  20. Fiscal 1998 research report. Study on the feasibility of microorganism biotechnology for effective use of environmental pollutants. Pt. 2; 1998 nendochosa hokokusho. Kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology riyo kanosei ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on the feasibility of microorganism biotechnology for effective use of environmental pollutants and unused resources. Microorganisms and microorganism enzymes for decomposing lignocellulose were viewed, and uses of hydrolysis products were summarized. Production of microorganisms applicable to fodder, composting, and production of energy sources (methane, hydrogen, ethanol) were studied. Use of vegetable fiber residues such as beer lees as fungus cultivation medium and conversion to valuable substances were also studied. Microorganisms treatment (MT) of wastes in fats and oils industry was summarized. Effective use of MT of protein waste from marine products was studied. MT of manures with the greatest impact on environment as livestock waste was summarized. The necessity of separate collection of domestic wastes, and composting and methane fermentation of kitchen garbage were reported. The feasibility of MT of plastic wastes, and decomposition of halogenated methane with high toxicity were also studied. (NEDO)

  1. FY 2000 survey report on the project on energy conservation/environmental preservation for oil corporations in Croatia by rehabilitation of oil refinery; 2000 nendo Croatia sekiyu kosha muke seiyusho no rihabiri ni yoru shene kankyo hozen project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of strengthening the international competitive force in the oil industry of Croatia and reducing greenhouse effect gas by introducing energy conservation technology, study was made of the rehabilitation of oil refineries (Rijeka and Sisak) of Croatia's oil corporation, INDUSTRIJA NAFTE d.d. (INA). Rijeka and Sisak Refineries have the oil processing capacity of 6 million t/y and 4.6 million t/y, respectively, but they were constructed during the 1960s-1970s and are now superannuated. In this project, the following are adopted: heightening of the temperature of raw material supply, surging avoidance control, reutilization of condensate water of vacuum distillation, heightening of MEA concentration, control of excess air ratio in heating furnace, preheating of combustion air in heating furnace, application of small-diameter pump impeller, the optimum control of steam/electric system, heightening of temperature of cleaning water of desalting device, stop of adoption of flare seal gas, etc. The energy conservation effect to be expected from the project is 43,065 toe/y in a total of the two refineries, and the reduction in greenhouse effect gas is 133,000 t-CO2/y. Further, the internal return rate is 53.12%, which is very attractive for INA. (NEDO)

  2. Promotion of the formation of environmentally friendly energy community (FY 2000). Demonstration of the gas turbine repowering waste combined power generation technology; 2000 nendo kankyo chowagata energy community keisei sokushin seika hokokusho. Gas turbine repowering haikibutsu fukugo hatsuden gijutsu jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Demonstrative operation was conducted of the super waste power generation system in which the low temperature steam generated in waste incinerator is raised in temperature using the combustion exhaust gas emitted after the power generation using another gas turbine for conducting the steam turbine power generation with high efficiency. The FY 2000 results were summed up. In the demonstrative operation, operation and data acquisition/analysis were conducted following the previous fiscal year by 25MW class gas turbine repowering waste combined power generation facilities (Takahama power plant). Further, four years after the start of operation, the secular variation was studied by disassembly/inspection of equipment. As a result of the operation, the thermal efficiency was approximately 35%, much higher than the existing waste power generation. It was verified that the power system was maintained by the same maintenance as that of the ordinary power system. Moreover, the important point of this system is that no special corrosion resistant materials are used and that the high-efficiency waste power generation was demonstrated by combining the existing equipment. It can be said that the super waste power system has high qualities for forming energy community as a regionally dispersed stabilized power source. (NEDO)

  3. Achievement report for fiscal 2000 on investigations and researches on promotion of utilization of waste energies that can deal with environmental load suppression; 2000 nendo kankyo fuka yokusei taio haikibutsu energy riyo sokushin chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 in investigating generation mechanisms and suppression of dioxins from refuse incinerators, and in investigating non-bromine flame retardant materials (having a possibility of generating hazardous material such as bromine-based dioxin during combustion). To produce poly-chlorinated dibenzo-para-dioxins (PCDDs)/PC dibenzo furans (PCDFs) (dioxins, but not containing Co-PCB) in a small fluidized bed combustor for simulated refuse derived fuel (RDF), both of chlorine source and hydrocarbon are required. If the primary combustion furnace temperature is high and the air excess rate is low, the concentration of the dioxins increase. In addition, since oxygen shortage in temporal and spatial locals or excessive concentration zone of unburned hydrocarbons imposes great effect, promotion of turbulence mixing is important. In producing dioxins, vaporization from dust due to interference with the combustion gas, and copper and iron catalysts have great effect, whereas SOx in the combustion gas has suppression effect. Flame retardant materials can provide specific flame retardation effect to particular plastics in a temperature zone slightly lower than the combustion temperature. The paper also describes development of new flame retardant materials. (NEDO)

  4. FY 1990 report on the survey of geothermal development promotion. Survey of environmental effects before jetting (No.34 - Kaminoyu/Santai area); 1990 nendo chinetsu kaihatsu sokushin chosa. No.34 Kaminoyu Santai chiiki - Funki zen kankyo eikyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-01-01

    For the evaluation of effects of geothermal development on the peripheral environment in the Kaminoyu/Santai area in the southwest part of Hokkaido, survey of the present situation of the environment was made. As a result of the survey, as to the climate of this area, the mean temperature, precipitation, etc. were almost the same as those of the nearest meteorological office of Hakodate, and the wind velocity was lower. Concerning the air, the mean concentration of H{sub 2}S was 0.8-3.6 ppb, SO2 was less than the detectable limiting value, Hg was 0.018-0.12 {mu}g/m{sup 3}N in average, and suspended particulate was 0.014-0.028 mg/m{sup 3}. Each of them satisfied the environmental criteria and the control level. The water quality satisfied the AA type criteria at every point of the river surveyed. The noise/vibration at the time of well drilling were 47-50dB at 10m measuring point and less than the lower limit of measuring at measuring points farther than 50m measuring point/100m measuring point. Every hot spring was drilled and spontaneously welling, and variations in spring temperature/welling amount were comparatively small. Micro earthquakes of 495 were observed in 47 days in total. Besides, survey was made of animals, plants, soils, scenery, etc. (NEDO)

  5. Industrial technology research and development project for global environment in fiscal 1998. Report on achievements in research and development of technologies for environment friendly catalysts; 1998 nendo kankyo chowagata shokubai gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes the achievements in fiscal 1998 in developing environment friendly catalyst technologies. Development was proceeded in a water decomposing hydrogen production system of double tank system utilizing visible lights. The system connects combination of visible light responding type semiconductor powders with an oxidation and reduction mediator via a membrane (consisting of a hydrogen ion permeating membrane and an electric conductor). Discovery was made on two sets of semiconductor-mediator combinations (to produce hydrogen and oxygen) that meet the requirements. A composite oxide powder catalyst of nano structure was also realized. Verification was made on water decomposing hydrogen production by using multi-layered membranes composed of a hydrogen producing catalytic membrane, a semiconductor membrane, and an oxygen producing catalytic membrane. By using selective oxidation that uses trace amount of nitrogen dioxide as a gaseous phase catalyst, such good results were obtained as conversion rate of 10%, and selection rate of 27% in methanol and 23% in formaldehyde. Selective oxidation mechanisms in iron carried silica and oxidized tin were elucidated theoretically and experimentally. It was elucidated by calculating chemistry that effect of adding nitrogen dioxide lies in draw-out of hydrogen, NO is involved in draw-out of O from CH3OO, and NOx is involved in synthesizing formaldehyde from CH3O. (NEDO)

  6. FY 1999 report on the results of the R and D of the environmental technology of recycling, etc. 1; 1999 nendo recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing environmental loads of waste and recycling waste, etc., the R and D were carried out, and the FY 1999 results were summarized. In the study of the technology for high-grade recycling of PET bottles, construction work for stabilization of the quality of drainage water was done of a demonstration plant with a treating capacity of 8,000t/y which was constructed in FY 1996, and the stability in long-term operation was examined. In the survey of fluctuations in flake quality, the verification data indicated that the plant could be stably operated. As to the alteration of the bottle cleaning process from wet method to dry method, stabilization of the label separation performance was recognized. By the above-mentioned matters, the technology to recycle/treat PET bottles was established. In the development of the technology to recycle waste plastics which are difficult to treat, assessment was made of the treatment capacity in dry distillation gasification furnace of shredder dust and gasification characteristics. As to the removal of wire harness, separation of glass from fine copper wire, etc., methods which are promising were proposed, and it was concluded that those were not valid as a treatment method in the plant scale in terms of economical efficiency. (NEDO)

  7. FY 1996 report on the results of the R and D of the environmentally friendly type hydrogen production technology. For public use; 1996 nendo kankyo chowagata suiso seizo gijutsu kenkyu kaihatsu seika hokokusho. Kokaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing the efficient hydrogen production technology using the hydrogen generation ability of microorganisms, the R and D were conducted, and the 1996 results were summed up. As to the R and D of the screening and breeding improvement of photosynthetic microorganisms, the following were conducted: measurement of hydrogen generation ability by the experiment on artificial solar simulated irradiation, characterization of breeding improvement strains, breeding of blue-green algae, survey/study of correlations between PHB metabolism and hydrogen metabolism, breeding improvement of photosynthetic bacteria by genetic characterization of hydrogen generation enzyme and genetic recombination, etc. Concerning the R and D of the quantity culture technology, a two-step experimental device combined with the photosynthetic bacteria multiplication process and the hydrogen generation process was fabricated, and functions were confirmed by the experiment using sugar-containing waste liquid. Also conducted were the acquisition of the data on the quantity culture test on anaerobic bacteria and photosynthetic bacteria using waste water containing cellulose, etc., fabrication/experiment of the quantity culture module reactor of photosynthetic bacteria using sewage sludge, experiment on the quantity culture of photosynthetic bacteria using raw refuse, etc. (NEDO)

  8. Design of environment-friendly and next generation-type conversion system for unused carbon resources by developing highly functional materials; Kokino zairyo kaihatsu ni yoru kankyo chowagata jisedai miriyo tanso shigen tenkan system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Wakabayashi, K; Morooka, S; Arai, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sakanishi, K [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

    1997-02-01

    Studies are conducted for the development of now-unused kinds of fossil carbon resources, such as low rank coal and heavy gravity crude oil, into higher-value liquid fuel. In the preliminary treatment process, the fossil carbon resources are dried by use of supercritical carbon dioxide, when it is found that the resources are disintegrated and water is desorbed. In a low rank coal liquefaction process using the NiMo/KB (Kefjen Black) catalyst, more than 60% is converted into oil, which rate is improved by use of the dual-temperature liquefaction process. This catalyst may be recovered by separation utilizing specific gravity difference. As a low temperature gasification catalyst, the alkaline carbonate-carried carbon catalyst is very quick at the initial stage of reaction. The perovskite-carried alkaline carbonate catalyst is high in carbon oxidizing/activating efficiency at low temperatures. The silica film deposited on an alumina-coated support tube is excellent in selectivity and speed as a hydrogen separating film, and a carbonized polyimide film as a carbon dioxide separating film. For the supercritical phase adsorption/separation of chemicals not to be distilled easily, the NaY-type zeolite functions effectively. Pd/ZrO2 serving as a carbon monoxide conversion catalyst enables the recovery of more MeOH when Pd grains are smaller in diameter.

  9. Fiscal 1994 survey report. Part 2. Study on soil environment remediation system using ecological information and functions; 1994 nendo seitaikei joho to seitaikei kino ni yoru dojo kankyo fukugen system no chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of the feasibility of soil environment remediation through detecting contamination of soil and changes in ecosystems caused by industrial activities, with attention paid to biological antagonists. In this fiscal year, based on the results of surveys conducted in the past, studies are continued mainly on hypersensitive biosensing technology using ecosystem functions, remote sensing technology to monitor the terrestrial vegetation and soil environment over wide areas, and soil environment remediation technology using biological antagonists and vegetation. In consideration of Europe's long experience in this field, seven organizations known for their accomplishments are visited, where interviews are held. There is a close relationship between soil environments and ecosystems, and ecosystems are provided not only with information on changes in soil environments but also with functions to remedy soil environments by minimizing secondary contamination. To put such information and functions to practical use, element technologies are indispensable, including hypersensitive soil environment biosensors and environmental remediation by identification and isolation of biological information carrying substances and by vegetation. Proposed in this report is a project for soil remediation by use of biological information and functions and for elucidation of biological antagonists. (NEDO)

  10. Research cooperation report for fiscal 1997 on the environment-friendly system for effectively utilizing water resources; 1997 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku itaku gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This effort exerted in cooperation with the Philippines aims to solve problems related to water resources such as stable supply and pollution of water through developing a waste water treatment/water reuse system which is easy to operate and maintain, and low in price. The ultimate goal includes (1) the construction of a waste water treatment/water reuse system comprising an anaerobic reaction tank and activated charcoal absorption tower, easy to operate and maintain, and low in price, (2) the employment of goods procurable in the Philippines, the goods including carriers for use in the anaerobic reaction tank, microbes for use in both aerobic and anaerobic reaction tanks, and activated charcoal for use in waste water reutilization, and (3) the establishment of optimum operating conditions for the waste water treatment/water reuse system by use of a pilot plant and the transfer of operating and managing techniques to the Filipino counterpart. In this fiscal year, investigations are conducted to disclose the actualities of waste water treatment and water consumption by primary industries in the vicinity of Laguna de Bay, and the waste water to be the object of study and the place of pilot plant installation have been selected. Also conducted are investigations into the carrier, microbe, activated charcoal, etc., for use in the anaerobic reaction tank. (NEDO)

  11. Studies on legal systems and public decision-making process of the environmental protection and natural conservation; Kankyo{center{underscore}dot}shizenhogo no mirai no tameno koukyoteki kettei to sisutemu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hayashida, Seimei [Hokkaido University, Hokkaido (Japan). Faculty of Law

    1998-12-16

    This study have dealt with the issues of how the policies of environmental and natural protection should be shaped in a democratic society, and what the optimal legal systems should be for realizing the policies. We have analyzed these issues from the following three points of view ; the first one is the legal philosophical issues of justice and moral values among individuals and organizations. Secondly, we analyzed the optimal deterrence system of organizations for pollution controls, etc. We studied crimes and illegal conducts by organizations and corporations themselves, and their employees under the principal-agency model. Third, we looked at the legal system itself and the foundations of environmental issues from the legal-philosophical aspect. Fourth, we analyzed how the social decision-makings on the environmental protection were produced, using the public choice theory. (author)

  12. Survey report on the environment harmonizing type energy community survey project for the coastal area in the Kawasaki ward in fiscal 1998; 1998 nendo Kawasakiku rinkaibu chiiki kankyo chowagata energy community chosa jigyo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In energy utilization in the 'Kawasaki Zero Emission Industrial Complex', optimal regional heat supply systems were discussed. The discussion was made from the viewpoints of introduction of saving-type energies, new energies and renewable energies, and environment preservation performance. The coastal area in the Kawasaki ward is planned of developing an industrial complex with an area of 8.4 ha for operation of about twenty companies. In the assumption of heat demand, four companies only were taken up as the object of the discussion, who utilize heat supply from steam as process heat source for their factories. The total heat demand quantity and heat demand pattern used for the discussion were assumed by hearing and actual record submitted from each company. Optimal systems were discussed on heat supply systems utilizing steam produced by steel mills, with the discussion made on waste heat recovered steam in processes and steam extracted from thermal electric power plants in the steel mills. As a result of the discussion, heat supply utilizing the steel mill steam was found capable of being provided with much lower price level as the estimated unit price than general direct steam supply, leading to a judgement that the system has business feasibility. (NEDO)

  13. New energy vision at Sabae City. Toward realization of 'environmental international city'; 2001 nendo Sabae shi chiiki shin energy vision. Kankyo kokusai toshi Sabae no jitsugen ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    With an object of accelerating introduction of and uplifting consciousness on new energies at Sabae City in Fukui Prefecture, a new energy vision was put into order based on the result of the initial stage investigation having been performed in the previous fiscal year. Solar light and solar heat energies will be introduced positively into public facilities, and at the same time works will be implemented to accelerate the proliferation thereof into general households. The target of introduction by the year 2010y is set to 2,600 kW by photovoltaic power generation, and the introduction thereof is planned to schools, nursery schools, municipality operated houses, and unattended facilities. With regard to solar heat water warmer, the present proliferation rate of about 7.3% will be raised to 15%. Regarding wastes generated from industrial areas, efficient energy extraction by thermal recycling is intended on the assumption of suppression of wastes generation, their re-use, and recycling. Systems may include the bio-gas system, cogeneration, and recovery of energies from plastics wastes. For acceleration of proliferation of new energies in general, promotion of introduction will be achieved on mini-wind power generation, small hydroelectric power generation, and fuel cell automobiles. (NEDO)

  14. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

  15. Fiscal 1998 research report on promotion of geothermal development. Environment impact research report (No. A-4 Kunbetsu-Dake area); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.A-4 Kunbetsu chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-06-01

    For extracting the areas to be conserved from the viewpoint of environment for the research on geothermal well drilling, the environment impact research was made on the protection and regulation states of animals and plants in Kunbetsu-Dake area. 46 species in 12 families of mammals were confirmed in/around the area by document survey, and among them 19 species in 10 families of mammals were important academically. 340 species in 55 families of birds were confirmed, and among them 79 species in 29 families of birds were important academically. 3 species in 3 families of amphibians, and 6 species in 4 families of reptiles were confirmed, and among them 1 species of amphibian was important. 873 species in 135 families of land insects were confirmed, and among them 20 species in 11 families were important. 1055 species in 115 families of plants were confirmed, and among them 126 species in 46 families were important. Most of vegetation was 9 or more in degree of naturalness. The peripheral area of Kaibetsu-Dake is the plant colony area specified by the 2nd basic survey on natural environmental conservation (Environment Agency). (NEDO)

  16. Fiscal 1998 survey for geothermal energy development promotion. Environmental impact survey report (No. B-7 Kuwanosawa region); 1998 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (No.B-7 Kuwanosawa chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This survey aims to learn the current states of environmental factors required for the comprehension of the impacts on surroundings of a structural boring for geothermal energy exploration. The target site is an approximately 10km{sup 2}-large area located among the mountains 20km south-south-east of Yuzawa City, Akita Prefecture. It is found that numerous animals and vegetables inhabit the Kuwanosawa region and its vicinity. They are 19 species of mammals in 10 families under 5 orders; 73 species of birds in 25 families under 10 orders; 6 species of reptiles in 13 families; 9 species of amphibians in 6 families under 2 orders; and 719 species of insects in 179 families under 17 orders. Valuable animals include flying squirrels, mandarin ducks, black salamanders, and small Gifu butterflies. There are 670 species of vegetables in 132 families. Valuable vegetables are Iinuma bulblets, wild rhubarb roots, and Amur adonises. Floras found in existence are a natural flora in the beech class area, compensatory flora in the beech class area, afforested area, and a flora in the crop land. No remarkable fluctuation was observed in the Takamatsu spa throughout the survey period. Fluctuations were observed in all the survey items at the Doroyu-Okuyama inn. (NEDO)

  17. Promotional operation for developing industrial technologies for global environment in fiscal 1998. International research exchange operation; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective of creating a new scope of study intended of solving global environment problems and structuring a new technical system, exchanges with overseas researchers and research institutions have been carried out subsequent to those in last year. In fiscal 1998, six researchers from different countries were invited to implement joint researches, and two overseas researchers were invited to an international conference on industrial technologies for global environment. In addition, in order to identify trends of research and development in overseas countries, two researchers were sent to universities in Germany and the U.S.A., and three researchers to international conferences and symposiums on the industrial technologies for global environment. It was intended to exchange technological information between overseas researchers and Japanese researchers who are performing the advanced researches on the industrial technologies for global environment, and to proliferate the latest items of technological information. Therefore, seven international seminars have been held, including the '98 Japan-China Global Environment Protection Symposium, 'substance migration and carbon circulation in coral reefs', 'plant bio-technologies in the 21st century', and the Fourth International Forum for Environmental Catalysts. (NEDO)

  18. Politics of water resources and environmental problem. US-Japan comparative policy history on the public district; Mizushigen kaihatsu to kankyo mondai. Public district no Nichibei hikaku seisakushi kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Mikuriya, T [Tokyo Metropolitan University, Tokyo (Japan). Faculty of Engineering

    1994-12-15

    With an objective to give some suggestion to the water resources policies for the future Japan, a comparative study was made on the water resources development policies in Japan and the water resources policies in the state of California, U.S.A. The study on Japan has been proceeded empirically based on specific data with regard to the development of electric power policies from the prewar to postwar times when the governmental electric power control was changed to incorporation of the nine electric power companies. The change may be identified from viewpoints of both profit and ideology. Noticing the `public corporations` established one after another for social capitals before and after the establishment of the Liberal Democratic Party, their relation with the water resources development policies was pursued in terms of actual proof and political science. The identity of the public corporations established in and after 1955 stands on the premise of free economy, rather than the controlled economy. This paper positions the water resources development policies in a broader context as the national land plan, and considers the problems that are expanding from flood damages, dam construction, industrial complex construction to environmental problems around the water. Comparative discussions on the Tone river system and the Colorado river system were left as the future assignment.

  19. Fiscal 1997 report on the feasibility survey of Japan`s cooperation into energy/environment related fields in Asian countries; 1997 nendo chosa hokokusho (Asia shokoku ni okeru energy kankyo kanren bun`ya eno kyoryoku kanosei chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A survey was made to study possibilities of Japan`s cooperation in tackling energy/environment problems in Asian countries. In 1995 the GNP growth rate was 2.6% in the world, while it was 7.9% in Asia showing a rapid growth. With the accelerating industrialization and urbanization, energy demand is now over three times as much as that in the 1980s. This means increases in waste and environmental pollution. Especially, the use of firewood in non-electrified areas is a serious problem the same as the slash-and-burn farming and deforestation. Also relating to the production of electric power, it is inevitable to choose hydroelectric power and renewable energy in addition to fossil fuels. Therefore, the necessity is heightening of various technologies for it and environmental protection technologies such as coal cleaning. Local areas, where the population density is extremely low and the electrification cost is high, became victims of elecrification. There the power system should be shifted from the central supply system to the local distributed one. For it, it is necessary to recognize an importance of the distributed type renewable energy which is friendly to the environment. The paper outlined the state of each country and energy by policy and environment. 10 figs., 83 tabs.

  20. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system - Dispatch of engineers. A. Project for supporting the introduction of the environmentally friendly type coal utilization system (model project)/pre-survey for the potential survey; 1999 nendo kankyo chowa gata sekitan riyo system kanosei chosa. Senmomka haken A. kankyo chowa gata sekitan riyo system donyu shien jigyo (model jigyo) - Kanosei chosa no jizen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of the improvement of coal utilization technology and environmental preservation, the paper conducted the pre-survey of the introduction of coke oven gas desulfurization facilities in China and pre-survey of potentiality of the environmentally friendly type coal utilization system in India. The pre-survey in China was made for Anyang Steel Group Co. Ltd. and Laiwu Steel Group Co. Ltd. to judge their adaptability as site for the demonstrative project on the introduction of coke oven gas desulfurization facilities. As a result, it was confirmed that the former satisfied the conditions on Japan side such as the space for installation and prospect for fund raising. However, the amount of COG treatment was larger than that planned at Japan side, and it was found that as to the recovered sulfur, the company wanted the solid sulfur different from the fused sulfur planned at Japan side. In the survey in India, explanations were made to India of CFBC and the fluidized bed cement sintering system, bio-briquette production facilities, facilities for environmental measures, coal reforming technology, etc. At the same time, the site survey was made to examine/analyze possibilities of spread/development of Japan's CCT. (NEDO)

  1. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

  2. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use of unused hydrocarbon resource, technology for development of environmental harmony type catalyst); 1995 nendo kokusai kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kankyo chowagata shokubai kaihatsu gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) technology for development of environmental harmony type catalyst. In 1), a survey was conducted of applicability of biological surfactant to prevention measures of pollution by heavy distillate. It showed that part of the biological surfactants is reaching a stage of its being industrially produced by gene recombination bacteria, but as a whole, biosynthetic genes have hardly been elucidated. In 2), a survey of high-grade treatment technology of petroleum coke was made. It pointed out that it is necessary to develop a technology which makes the most of features of petroleum coke and allows defects. In 3), scientists and engineers of Japan and Europe searched for themes on which they can jointly study in the fields of NOx removal catalyst, up-grading of fuel, and development of catalyst combustion of fuel. 287 refs., 136 figs., 128 tabs.

  3. FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

  4. Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

  5. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

  6. Report on the research and development achievements in fiscal 1999 on the international research cooperation project for comprehensive development and utilization technologies for gas hydrate resources; 1999 nendo gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the achievements in fiscal 1999 on development of gas hydrate resources. As a result of synthesizing gas hydrates in deposit systems, identifying stability zones in compositions, and studying thermal conductivity and dielectric constant of the deposits, the estimation accuracy has been enhanced steadily in estimating hydrate existing areas in actual frost areas. In the collecting technologies, a proposal was presented for a system by which carbon dioxide is introduced into ground beds at the same time as recovering gases, and gas hydrates are displaced with carbon dioxide hydrates. The displacement phenomenon was verified experimentally by controlling temperatures and pressures. Even below the freezing point, the production rate of the carbon dioxide hydrates is fast if it is above minus 4 degrees C. Salt diffusion behavior important in control of the production and decomposition, and action mechanisms of production and suppression agents were made clear microscopically. Experimental and theoretical discussions were given on dynamics of the production and decomposition. The cage occupation rate of methane hydrates was quantitatively measured successfully by using the Raman spectroscopy. Hydrates of gas mixture were utilized to have verified the possibility of separating the gas mixture constituents. (NEDO)

  7. Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

  8. Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

  9. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  10. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 1. Research study on integrated evaluation and development plan; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on the WE-NET project in fiscal 1996. The WE-NET project is composed of various elemental technologies such as hydrogen production, transport, storage, low-temperature material, utilization and hydrogen combustion turbine. The organic integrated cooperation and coordination between individual subtasks are indispensable for effective promotion of the project and optimization of the total system. The current R and D states of every elemental technology were surveyed, and its findings were utilized for coordination of the whole project and examination of the research project including pilot studies. Eleven important items in the total coordination including a total system cost and safety measures in a developmental stage were examined. The development results for 4 years of fiscal 1993-1996 were assessed together, and the draft working plan for fiscal 1997-1998 was also decided. The verification test plan of a hydrogen combustion turbine scheduled in Phase II was studied, and the basic plans of development step were proposed. The draft report of a transition scenario was also prepared. 6 figs., 68 tabs.

  11. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  12. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  13. Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

  14. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

  15. Fiscal 1997 report on the results of the cooperative research project under consignment from NEDO on technology for simply setting-up of the molding conditions of engineering plastics; 1997 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (Engineering plastic no seikei joken kan`i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A cooperative research project was carried out between Japan and Thailand with the aim of developing a system which can simply set up molding conditions using as elements the technology on mold design and injection molding in plastic parts production and the experiment/evaluation technology for making sure of the quality of molded products. In fiscal 1997, based on the basic plan worked out in the previous fiscal year, molding equipment, auxiliary equipment, mold, experimental equipment, injection molding CEA system, etc. were installed at Thailand`s BSID (Bureau of Supporting Industries Development). Supported by equipment manufacturers, the technical guidance was given for operation/maintenance/control of all equipment. At the same time, researchers were sent from Japan, and the joint research was started. Japan received three researchers from BSID for training of molding technology, injection molding CEA program use technology, and experimental evaluation technology. The engineering plastics used for study are polyacetal, polyamide and polycarbonate. 17 refs., 68 figs., 14 tabs.

  16. FY 2000 report on the survey of the calculation of the overall conversion efficiency in case of using natural gas for fuel cells, etc.; 2000 nendo chosa hokokusho. Tennengas wo nenryodenchi ni mochiita baai no sogo henkan koritsu no santei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of evaluating the efficiency of fuel cell including the fuel supply system, survey was made of drilling of gas resource, conversion to liquid base fuel, transportation, storage, etc., the energy conversion efficiency was studied considering reforming characteristics of various fuels. In the comparison between LNG, methanol, DME and GTL that originate in natural gas and LPG and naphtha that originate in oil, a big difference is that methanol, DME and GTL were made through the conversion process with the large energy consumption. Namely, by the time before the reforming into hydrogen, the oil base indicated a higher efficiency in secondary energy fuel production than the natural gas base. Further, the reforming efficiency is the highest in methanol and DME, and there is a little difference between the integrated fuel cell (normal pressure) and the hydrogen production use fuel cell (pressurized). Concerning city gas and GTL, the efficiency is lower, affected by S/C. The overall efficiency is determined considering the conversion efficiency in other stages since it is determined by the conversion efficiency of up to the raw fuel and the energy conversion efficiency at PEFC. (NEDO)

  17. Fiscal 1999 technical research report. Development project on prompt-effect international standards for developing new industry (Comprehensive survey and research concerning promotion of international standardization); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For encouraging the promotion of international standardization involving the six subjects of advanced technology taken up under the above-named project, wide-range investigations are conducted into measures for international standardization, the activities of international standardizing agencies and organizations, and the approaches of European and American business corporations to this issue. Technical literature and material are studied in Japan, and interviews are held overseas with responsible persons at organizations and corporations engaged in this task. At Standards Development Organization (SDO) of America, verification tests are under way for early development into international standards of technical standards it has so far developed independently. For the strategical utilization of intellectual property incorporated into its technical standards, SDO accepts that the best policy is to win approvals from patent proprietors at the early stage of standardization process by presenting them with conditions about patent implementation. In Europe and America, for the enhancement of their competitive power in the international theater, governments and civil sectors cooperate with each other for the establishment of international standards and, in business corporations, the management takes the initiative in coping with the issue with an understanding that there are business opportunities in international standardization. (NEDO)

  18. Joint research report of Central Research Institute of Electric Power Industry and Japan Research Institute Ltd. Conceptual construction of Japanese type end-use model; Denryoku chuo kenkyusho Nihon Sogo Kenkyusho kyodo kenkyu hokokusho. Nippon gata end use model no gainen kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    The concept of Japanese type demand analysis model (end-use model) was constructed for the efficient management of electric power companies and efficient power utilization. Diffusion and use conditions of domestic air conditioners are considerably different depending on local life style and climate. In order to design demand measures considering combination of appliances in every market segment, demands in an end use level (end demand level, each appliance level) should be acquired. The basic structure of the model is composed of various exogenous variables such as weather data, price and ups and downs trend of customers, and various appliance data such as size, efficiency and energy consumption rate, and various customer data such as possession rate of appliances and number of customers. The final energy demand is estimated by integrating the above variables. By systematizing the stored data of precise actual load conditions, construction of DSM (demand side management) strategy becomes possible by using computer tools. 8 refs., 15 figs., 13 tabs.

  19. Report on achievements in fiscal 1988 on research and development of the photoreactive materials under the next generation basic technology research and development project. Comprehensive surveys and researches on photoreactive materials; 1988 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokuksho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1988 on comprehensive surveys on photoreractive materials. Based on the research and development institution for the next generation basic technology under the initiative of the Agency of Industrial Science and Technology, development is being promoted on photoreactive materials, or photochromic materials and photochemical hole burning (PHB) materials (materials in which molecular structures and assembly state can be changed reversely by actions of light, leading to expectation of application thereof to ultra-high density recording, displays at high resolution, and light switches). In order to achieve smooth and efficient promotion of the development thereof, development of the related technologies inside and outside the country was surveyed and discussed. Comprehensive surveys and researches were also carried out on the common basic technologies by looking to the well-informed people for guidance on the research. This fiscal year has held joint committee meetings to which lecturers were invited to discuss respective problems in the research and development trends. In addition, as the domestic survey, the status of research and development at the Tsukuba University was surveyed on photo-responsive polymeric gels. Furthermore, as the survey on the overseas technological trends, information related to photoreactive materials was collected mainly on photochemical burning materials in the U.S.A., and the research trends were surveyed. (NEDO)

  20. FY 1991 report on the results of the surveys on the technologies for forming composite materials. Research and development of the new technologies for forming composite materials (Comprehensive surveys and researches); 1991 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This project is aimed at development of new technologies for forming composite materials by studying the methods for controlling structures of ceramic- and metal-based composite materials, and also at development of the technologies for forming near-net shapes utilizing the phenomenon of superplasticity. The literature survey is conducted to help promote the developments, and the abstracts of the major papers are pigeonholed into 4 general categories; (1) production and properties of ceramic-based composite materials, (2) superplasticity of ceramic-based composite materials, (3) production and properties of metal-based composite materials, and (4) superplasticity of metal-based composite materials. This paper summarizes the abstract of these papers. The category (1) includes carbon fiber reinforced Sialon composites produced by polymer pyrolysis, the category (2) includes superplasticity of functional ceramics, and comparison of tensile and compressive creep behavior of a superplastic yttria-stabilized zirconia-20 wt.% alumina composite, the category (3) includes in-situ metal matrix composite, and the category (4) includes high strain rate superplasticity in whisker-reinforced alumina composites, and application of superplasticity to fabrication of metal matrix composites. (NEDO)

  1. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal conception design (Associated material 3 - materials related to U.S. geothermal analysis contractors and consultants); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei futai shiryo 3 (Beikoku chinetsu kaiseki contractor oyobi consultant kankei shiryo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    This paper summarizes the U.S. geothermal analysis contractors, including the Aero Service Corporation, the EG and G Group, the QEB Group, and the Republic Geothermal, Inc., and the consultants, including the Remote Sensing Consultants. For the Aero Service Corporation, the paper states histories of and books written by major personnel. For the EG and G Group, the paper states the outlines of such companies as EG and G Services, EG and G Geometrics, Mars Associates, Inc., and UURI, as well as histories of and books written by major personnel. For the QEB Group, the paper states the outlines of such companies as QEB, Inc., and Eureka Resource Associates, Inc. as well as histories of and books written by major personnel. For the Republic Geothermal, Inc., the paper states the company outline, histories of and books written by major personnel. For the Remote Sensing Consultants, the paper states the history of and books written by Dr. R.J.P.L. Lyon. (NEDO)

  2. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Comprehensive research and development for reducing ABS (MABS) sensor system into small module for enhancing vehicle steering safety; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Koji no sharyo soansei wo jitsugensuru ABS (MABS) sensor system no kogata module ka ni tsuite no sogo kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The effort aims to develop a sensor system to enable overall VDC (vehicle dynamic control). The goal is to manufacture a small module type sensor system more than 20 times higher than the conventional type in responding speed and accuracy, which will use a novel ABS (anti-lock braking system) capable of direct and real-time measurement of axial forces in the four directions. The prototype module will be a package in which a system-on-a-chip accommodating peripheral circuits is integrated with a sensor. In the effort to develop a novel multi-axial sensing system (MASS) for a smaller ABS, a circuit optimization technology was developed. A dedicated IC (integrated circuit) was developed for a system to process a large volume of signals. In the effort to develop technologies for packaging the novel sensor system and for constructing modules, technologies were developed for integrating sensor components and an IC into one, module junctioning, module installation, simplification of the installation process, and for the manufacturing of modules. Developed in the effort to optimize MASS were technologies involving the selection and evaluation of sensor components and the enhancement of such processes, optimization of the sensor itself, and the improvement of the sensor system for higher efficiency in calculation. Sensor modules were tested aboard vehicles and the compatibility of the system-on-a-chip with the MASS module was confirmed. (NEDO)

  3. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

  4. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  5. FY 1992 Survey report of the technologies for creating/processing advanced biomaterials. Research and development of the technologies for creating/processing advanced biomaterials (Comprehensive survey and research); 1992 nendo senshin bio zairyo no sosei kako gijutsu chosa hokokusho. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, item (6) peptide having activity with plant, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  6. Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

  7. Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 1. Survey/research for the comprehensive evaluation and developmental plan; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper described the results of the FY 1998 WE-NET project survey. WE-NET is composed of various element technologies such as hydrogen production, hydrogen transportation, storage technology, low-temperature materials, hydrogen utilization, and hydrogen combustion turbine technology. Therefore, considering the effectiveness as a total system, it is extremely important to traversally evaluate the situation of the R and D of each technology and developmental achievements and to work out developmental plans with integration, considering the effectiveness as a total system. From viewpoints of making effective promotion of the project and attempting optimization as a total system, it is necessary to make organic/comprehensive connection and adjustment among individual subtasks all the time. In this survey/research, in the case of proceeding with the above-mentioned studies, a committee having knowledgeable persons and learned persons as members was established. There, an investigational study was conducted over the whole WE-NET structural technology, and at the same time the following were attempted: the constant/mobile comprehensive adjustment of the whole project, evaluation of the developmental results, and optimization of the developmental plans. The results obtained in 6 years of Period I were evaluated traversally and comprehensively, and how to proceed with the development in Period II was proposed, which showed the developmental continuity. (NEDO)

  8. FY 1999 project on the development of new industry support type international standards. Standardization for securing mutual connection among informative household electric appliances; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted with the aim of the international standardization for securing mutual connection among informative household electric appliances, and the FY 1999 results were summarized. In FY 1999, the following were conducted: trial manufacture (for mass production) and evaluation of wide band POF (plastic optical fiber), trial manufacture and evaluation of home use small connector, and trial manufacture and evaluation of optical transceiver module. Various data required for the targeted standardization (transmission band: S400 or more, transmission distance: 100m) were obtained. In the next fiscal year, tests to demonstrate validity/reliability of the data are conducted so that the standards to be accepted as an international standard can be established. In the study of strategies of international standardization, the contents of the standards proposed were discussed, and activities of IEC/TC100 (multi-media) and the related TC were investigated. Early in the next fiscal year, the TC to be proposed is fixed, and international proposing activities are started such as the introduction of the standardization for this R and D to the organizations and persons concerned overseas. (NEDO)

  9. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

  10. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  11. Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

  12. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 2: Collected data); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 2 (shiryoshu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    As to the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was made in FY 1999, the comprehensive analysis was conducted, and the data were arranged. In relation to the surface survey, data on the following were described: geological survey, supplementary surface geological survey, soil gas survey, precision gravity survey, supplementary gravity survey and 3D model re-analysis, electromagnetic survey, etc. With relation to the well survey, data on the following: wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, N9-AY-5, N10-AY-6, N10-AY-7 and N10-AY-8, survey of cores of existing wells, temperature/pressure logging of wells remaining stationary after having been left long, sampler logging, etc. In relation to the jetting test, data on the short-term jetting test on wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, etc. With relation to the evaluation of reservoirs, data on the pressure monitoring, results of the reservoir simulation, etc. (NEDO)

  13. FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

  14. FY 1997 report on the survey on the current residential waste treatment and integrated utilization of waste including heat supply in Shanghai city; 1997 nendo chosa hokokusho (Shanghai shi ni okeru seikatsu gomi shori no genjo narabini kyonetsunado wo fukumu sogo riyo ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Survey was made on residential waste treatment in Shanghai city. Shanghai city with nearly 13 million registered residents produces on average 10,000-11,000 tons/day residential solid wastes. Such wastes are basically disposed by land filling. A landfill site has a current disposal capacity of 7,500 tons/day, and is scheduled to be expanded up to 9,000 tons/day. Problems of waste disposal in Shanghai city are as follows: transportation of wastes collected in the city by trucks, transportation through transit stations to the landfill site by ships, and high disposal cost. Shanghai Environmental Sanitation Bureau is pursuing researches on recycling of wastes, reduction of wastes and harmless treatment in place of conventional land filling. As the survey result, adoption of complete separate collection of wastes is basically important, and application of the latest technologies such as combustion treatment for every waste, heat use, gasification fusion furnace, and RDF (refuse derived fuel) for coal-firing boilers should be considered. 86 figs., 18 tabs.

  15. Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

  16. Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (Second volume: comprehensive investigation and research); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho (sogo chosa kenkyu). 2. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Technology was developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation was introduced, and by fixing the peptides to the surface of a base plate such as silica glass or modifying the surface with them. As the related technological investigation, the following six areas were surveyed. (1) Structural design of peptides, (2) synthesis of peptides by chemical and enzyme methods, (3) synthesis of non-natural amino acid and its introduction into peptides, (4) structural analysis of peptides, (5) physiological activity of peptides, and (6) materialization and functional manifestation of peptides. With the exception of the area (5) consisting of one advanced research case, other areas were constituted of analysis, general remarks and research cases. The area (6) was constituted of materialization technique 1 and 2, film function and peptide, catalytic action 1 and 2, and one research case; the materialization technique was defined as a technique for modifying the surface of a synthetic resin, metallic or silica glass substrate with functional peptides; and an explanation was given to the present state of the fixation, pattern formation and integration technologies. (NEDO)

  17. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

  18. Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

  19. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 1: Forth survey); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 1 (Dai 4 ji chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    The paper reported the results of the long-term jetting test, etc. which were carried out as the forth survey of the geothermal development promotion survey in the Akinomiya area, Ogachi town, Akita prefecture. The jetting induction and the situation of production/reduction were described as follows. N9-AY-3 began to well spontaneously after being induced by sending air up to wellhead pressure of 4.8 MpaG. Damping was recognized for a month or so after the start of jetting. After that, however, no damping was recognized, nor was recognized the deterioration of the fluid enthalpy with age. The pH of geothermal water was definite, approximately 8, and the electric conductivity and Cl concentration were 8,500 {mu}S/cm and 2,600 mg/L, respectively. The maximum jetting capacity of N10-AY-8 was 10.4t/h in steam and 8.9t/h in geothermal water at wellhead pressure of 0.24 MPaG, and after that, it showed a tendency to lower. The flow rate of reduction of N8-AY-1 changed from 80-90t/h at the beginning to 60-70t/h. With the continued reduction, the lowering of reduction capacity was recognized. In the test, the following were carried out: temperature/pressure/spinner logging, test on pressure transition, survey of fluid properties, survey of jetting microseisms, etc. (NEDO)

  20. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  1. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  2. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Comprehensive survey); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (sogo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys and studies were conducted to facilitate and invigorate research, development, and economic activities and to provide technology related intellectual assets in an organized, systematic way. In the survey related to the buildup of intellectual infrastructures, questionnaires were sent to 789 organizations in the industrial and academic domains concerning measuring standards, reference materials, base for information on biological resources, base for safety management of chemical substances, base relating to human life and welfare, and base of knowledge relating to materials. On-site surveys were also conducted in Asia, Australia, North America, and Europe. Concerning 10 inorganic reference solutions whose development is urged because they are related to environments, raw materials for them were selected, required purity levels were defined, and methods for measurement and evaluation of safety when in prolonged preservation were investigated. Conducted in the research and development of individual subjects were database buildup on thermophysical properties, research into long-term durability of heat-resistant composite materials, research into textural structure and characteristics as materials of sintered bodies of fine ceramics, database buildup on the safety of non-ferrous metals, studies of base of human characteristics measurement, and the like. (NEDO)

  3. FY 1989 report on the results of the next generation industrial basement technology R and D project - R and D of photo-reactive materials. Comprehensive investigational research on photo-reactive materials; 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    As to photochromic materials and photochemical hole burning (PHB) materials, for the purpose of smoothly/efficiently promoting the R and D, the common basic technology was comprehensively surveyed as well as survey/study of the related technology development in Japan and abroad. In FY 1889, a joint committee was held, and a meeting was held of lectures given by lecturers from outside on the following: reversible response LB multilayered film and 2D optical switching element, photochemical HB and solid polymer, photovoltaic excitation dynamics of polymer solid, wavelength variable/semiconducting laser, optical memory, etc. A meeting for study/discussion on the details was also held. Items for the meeting were as follows: optical orientation control of nematic liquid crystal by photochromic surface, design of photochromic molecules, molecular movement and photo-reactivity in molecular aggregation system matrices, PHB spectra and mesoscopic structure control, continuous HB using semiconducting laser and sub-picosecond photon echo, quinone system derivative PHB in polymer matrices, etc. (NEDO)

  4. General report of entrustment investigation for demonstration tests of turnover from oil to methanol in the thermal power plants in fiscal 1995. Total assessment of methanol using power generation technology; 1995 nendo sekiyu karyoku hatsudensho methanol tenkan nado jissho shiken itaku gyomu hokokusho sokatsu hokokusho. Methanol riyo hatsuden gijutsu sogo hyoka chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To promote the introduction of methanol fuel into the thermal power plants, total assessment was provided. For calculating the methanol production cost, the plant was assumed to be constructed in the Southeast Asia or Middle East. Two methods, i.e., steam reforming and gaseous phase fluid methods, were investigated. Since the price of natural gas is low in the Middle East, the methanol production cost by the gaseous phase fluid method is estimated to be about 1.5 yen per thousand kcal. The transportation cost can be reduced into one-half to one-third of current cost using a large-scale tanker. Although the heating value of methanol per weight is lower than that of LNG, the volume flow of methanol is similar to that of LNG due to its low specific gravity. Conceptual designs were conducted for some power generation systems, such as gas turbine of combined cycle, diesel engine, and fuel cell. The power generation cost was estimated to be 8 to 9 yen per kWh, which depends on the receiving price of methanol. It is nearly equivalent to that of LNG combined cycle power generation. There are no problems of air pollution and ash disposal. When considering the long-term security of energy sources, the use of methanol would be one of the selections as utilization of natural gas. 6 refs., 33 figs., 25 tabs.

  5. Report on the research and development under a consignment from NEDO of high temperature carbon dioxide fixation and utilization technology for fiscal 1996; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku gyomu seika hokokusho. Nisanka tanso koon bunri kaishu sairiyo gijutsu kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the prevention of global warming, this R and D is aimed at separating/recovering high temperature CO2 from high temperature gas at 300degC or above and developing technology for effective use of the recovered CO2 as measures taken for reduction in CO2 emissions from the fixed emission sources. In this fiscal year, the following were proceeded with: heightening of separation performance evaluation technology, promotion of technical development of ceramic separation membranes and supports, and development of element technology of modular integration. In the examinational research on separation technology and system optimization, the following were conducted: survey of trends of the technical development, conceptual design of plant and prediction of process behavior, assessment of applicability of the process, and study of effects of utilization/spread of the developmental technology. In the former R and D, borosilicate glass powder rich in alkali is formed on the ring by joining the trially manufactured hollow fiber type membrane and the same form alumina cylinder, and sealing property and strength which stand measurement of permeability were confirmed. In the latter, an innovative process applied with CO2 high temperature separation technology was studied to examine effects of the spread of high temperature gas separation technology. 403 refs., 478 figs., 134 tabs.

  6. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for enhanced interoperability between optical disk systems; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out for the enhancement of logical format-based interoperability between optical disk systems for the purpose of presenting propositions for international standards. That is, UDF (universal disk format) defined by OSTA (Optical Storage Technology Association) was taken up against the volume/file structure defined by ISO/IEC13346, and efforts were exerted to substantiate environments for its compatibility test and to develop specifications to achieve such enhanced interoperability. In this fiscal year, specifications were drafted for application program interfaces for the UDF-based file system and UDF security augmentation. These would be presented to IEC (International Electrotechnical Commission) and OSTA, respectively. Their Japanese versions were submitted to the Ministry of Economy, Trade and Industry of Japan, for publication as standard-related information. Maintenance of UAF (universal accessible file) system-compliance test tools were accomplished in response to user requirements and to the updating of UDF-compliance test disk specification. (NEDO)

  7. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  8. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology wa