Demonstration test on the heat pump system, thermally utilizing the domestic waste water. Result of the collecting test on an air conditioning system, Hokkaido Electric Power Gymnasium, Tomari; Seikatsu haisui netsuriyo heat pump system jissho shiken. Tomari Hokuden taiikukan reidanbo system no sainetsu shiken kekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Honma, T; Yamada, K; Watanabe, K [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1995-06-14

A heat pump system utilizing the domestic waste water was introduced into a gymnasium owned by Hokkaido Electric Power to elucidate the applicability of domestic waste water as a thermal source of heat pump in the cold region. The gymnasium is a two-storied concrete building with the floor space of 2292m{sup 2}. Ground water at temperatures from 10 to 20{degree}C is utilized for the water supply. Made to flow together as waste water, the dirty water and daily exhaust water are discharged at the rate of 100t/day into a river after passing through the septic tank. Higher by 5 to 15{degree}C than the atmospheric temperature, the discharging temperature is kept higher than 10{degree}C even during the very cold period. The domestic waste water is almost neutral in pH, and normal in both SS and BOD. The heat pump was utilized for two stages, i.e., thermal collection and temperature heightening. The capacity of a sewage storage tank tank was made to be 170m{sup 3} to meet the thermal load of 139000kcal/h in the gymnasium. The temperature of 15{degree}C could be kept during the air heating trial. The system is about 2 in coefficient of performance. The K-value of heat exchanger decreased by about 30% after seven months of operation. Upon its overhauling, its K-value recovered to 2.37, so that it must be overhauled once a year. 5 refs., 15 figs. 4 tabs.

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. The current fiscal year performed data collection and long-term continuous operation according to the durability test program for the device installed with inverter to protect grid connection, as the continuation from the previous fiscal year. In the electrical characteristics, although no large changes have been found in AC overvoltage and AC undervoltage, instability was observed in the detection level. With regard to temperatures in different components, the temperature rise has become nearly the same as in the maximum output continuous operation as a result of the repetition of the operation and shutdown, whereas the influence on the electrical and thermal stresses have increased. Particularly, when temperature rise in the AC side noise filter was given observation, the measurement of conductive high-frequency terminal voltage showed a value higher by several ten dB than in the previous fiscal year. The current fiscal year has gone farther to starting the measurement of noise electric field intensity as the base of electromagnetic interference. (NEDO)

Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Discussions and evaluations have been performed on the safety and durability of the device installed with inverter to protect grid connection being an important device in the photovoltaic power generation system. In discussing the durability test items, electrical property changes were observed on AC overvoltage, AC undervoltage, frequency rise, and frequency fall, as the continuation from the previous fiscal year, in order to evaluate temperature rise in different parts due to lapse of operation time and the effects of thermal stress in each component on the stress of the entire product. Furthermore, verification of single operation detecting function, tests on sudden input power change, sudden grid voltage change, and measurement of conductive high frequency terminal voltage were conducted in addition to the above observations. In discussing the durability test methods, repetition of operation and shutdown during the rated operation was adopted in place of the simulated operation using variation in the insolation having been discussed in the previous year. As a result of the tests, no noticeable changes were recognized from the evaluation result after a lapse of 5,000 hours from the start of the operation, as compared to those after the aging operation. (NEDO)

Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology. Evaluation on durability of device installed with inverter to protect grid connection; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka - Inbata tsuki keito renkei hogo sochi no taikyusei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Tests and discussions have been performed on the safety and durability of the device installed with inverter to protect grid connection, being an important device in the photovoltaic power generation system. The particularly important requirements demanded in the device were specified as maintenance of electric power quality, coordination with the protection system in the grid side, and assurance of safety of personnel and facilities. The current fiscal year has performed operation corresponding to that in the actual field for 20 years in total, and the evaluation tests on electrical characteristics and electric power quality. This paper summarizes the achievements in four years including the results available up to the previous fiscal year. Although no large change has been identified in the electrical characteristics, variance has been found in the detection time of overvoltage in the grid side. With regard to the electric power quality, the value has exceeded 89 dB as the determining condition for the certification test in the conduction interfering waves of 5 kHz to 10 kHz. In addition, it was confirmed that the conductive high-frequency noise terminal voltage in the grid side after the repetition of operations and shutdowns tends to increase according to the operation lapse time. (NEDO)

Research report for fiscal 1995 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1995 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1995. In the outdoor exposure test on solar cell modules, multi-crystalline silicon solar cell modules were selected as the test specimens, and thermo-couples were embedded in the modules to measure the temperatures. Also for the purpose of comparison, storage test specimens were stored in a constant temperature and humidity chamber. The exposure tests were carried out in three locations of the city of Choshi in Chiba Prefecture, the Miyako Island test site in Okinawa Prefecture, and the Miyako Island seashore. In the measurement and evaluation, appearance observation and measurements of output characteristics and insulation resistance were executed in summer and winter. No noticeable changes were observed in the measurements after lapse of four months and six months. In the outdoor exposure tests of metal test pieces, aluminum alloys were tested for corrosion caused by contact with different kinds of metals. Although the test period was short in the current fiscal year, difference in corrosion degrees in the aluminum alloys was found already in three months. (NEDO)

Research report for fiscal 1996 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1996 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure, with the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system. This paper summarizes the achievements in fiscal 1996. In the outdoor exposure tests on solar cell modules, results of the tests were derived for up to 18 months after the start of the exposure at Choshi City, Miyako Island and the Miyako Island seashore. In the appearance observation, some white rust has appeared in the contact section of the aluminum frames of the solar cell modules and fixing screws, which have been exposed at Miyako Island and the Miyako Island seashore, but no changes that may give influence on the performance of the solar cells have been observed. The results showed performance similar to or slightly inferior to that before the exposure as a whole. The insulation resistances were all found good. According to the result of the outdoor exposure test of metal test pieces, noticeable difference in the corrosion degrees was recognized in the contact corrosion section of the aluminum alloys exposed in three areas having different meteorological and environmental factors. Electroplated zinc was found to have severer pitting corrosion in the contact sections than treatment-free zinc. (NEDO)

Research report for fiscal 1997 on analysis and evaluation of demonstration tests for establishment of residential photovoltaic power generation load leveling technology, of which evaluation on weatherability of devices used in residential photovoltaic power generation system; 1997 nendo kenkyu hokokusho. Jutaku you taiyoko hatsuden fuka heijunka gijutsu tou kakuritsu jissho shiken ni kansuru kaiseki hyoka no uchi jutaku you taiyoko hatsuden system kiki no taikosei hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With the objectives to analyze and evaluate the safety and reliability due to aging of the devices used in the residential photovoltaic power generation system, weatherability tests have been performed on devices used in the residential photovoltaic power generation system by means of exposure. This paper summarizes the achievements in fiscal 1997. In the outdoor exposure tests on multi-crystalline silicon solar cell modules at Choshi City, Miyako Island and the Miyako Island seashore, the output characteristics after the exposure tests showed a result that the insolation intensity and the change in the short circuit current are approximately proportional, and the temperature in the module and the change in the open voltage are inversely proportional. The module characteristics retention rate showed no change in the 29-month exposure at all of the three exposure locations. The insulation resistance in the exposure test specimens have been good at 2,000 M{omega} or more in all the locations until 18 months have elapsed. However, the test specimens in Miyako Island and the Miyako Island seashore showed 99 M{omega} after 23 months, and 129 to 1,774 M{omega} after 29 months. According to the outdoor exposure tests of metal test pieces, noticeable difference was found in corrosion due to difference in the environment by each exposure location, whose order of the corrosion degree was the Miyako Island seashore > Miyako Island > Choshi City. (NEDO)

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.2 volume. Pilot plant verification test; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (pilot plant jissho shiken). 1997 nendo hokokusho (daini bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to a high efficiency waste power generation system using general waste as fuel, the details of the following were described: design/construction management and operational study of pilot plant, design/manufacture/construction of pilot plant, and study of an optimal total system. Concerning the construction management and operational study, the paper described the application for governmental/official inspection procedures and taking inspection, process management of pilot plant, site patrol, safety management, management of trial run of pilot plant, drawing-up of a verification test plan and test run, etc. Relating to the design/manufacture/construction of pilot plant, an outline of the pilot plant was described. The paper also stated points to be considered in design of furnace structure and boiler structure, points to be considered of the verification test, etc. As to the study of an optimal total system, the following were described: survey of waste gasification/slagging power generation technology, basic study on RDF production process, survey of trends of waste power generation technology in the U.S., etc. 52 refs., 149 figs., 121 tabs.

FY 1999 report on the verification test on the system interconnection of the photovoltaic power system in Malaysia; 1999 nendo Malaysia ni okeru taiyo denchi hatsuden system no keito renkei jissho shiken seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

JET and SIRIM Behad, which is the standards and industrial research institute in Malaysia, worked this project together, and installed the Photo Voltaic Generation System (hereinafter refferred to as 'PV system') on the roof of the research building for researching basic conditions in the practical use of the PV system by gathering basic data. The power quality of a supply system necessary for a grid connection of the PV system was researched in the evidential experiment. Moreover, the invasion level and the invasion frequency to the PV system of the thunder surge by the peculiar weather condition in this region were researched. In addition, the requisite for the islanding function for the alternative emergency power supply was investigated. The contents of this project were composed of the three items. (1) research of the power quality in low voltage distribution system. Before and after the PV system is connected with the supply system, basic data concerning the power quality of the voltage, the current, and the frequency fluctuation, etc. in the system was collected. (1)measurement and investigation of the power quality under the current low voltage distribution system. By connecting ad monitoring recorder with a lower voltage distribution system, the current power quality i.e. voltage, current, frequency the fluctuation of voltage and frequency at the regular time were measured and investigated. (2) The power quality in the supply system grid connection of the PV system was measured and investigated. The voltage and the frequency in the case of supply system grid connection of the PV system were compared with the current state of preceding clause 1 and the stability of the power quality was evaluated. Moreover the output power of the solar battery was connected with the measurement device and then the surface temperature of the solar battery module, DC voltage, current and quality of solar radiation were measured. The subject in the practical use of the PV system in Malaysia was extracted through these experiments. (2) Research of level and frequency of the thunder surge. 1. Measurement of level and frequency of the thunder surge by the thunder surge counter. The thunder surge counter was set up respectively on the positive line and the negative line of the solar battery. These signals are taken into the memory of the thunder surge counter, and the level and the frequency data of the thunder surge which invade the PV system were accumulated. 2. Evaluation by simulation. The PV system was evaluated to the thunder surge obtained in preceding clause 1 by the simulation. In addition the simulation analysis was conducted by the system equivalent circuit on the assumption of the thunder surge current at the location of the system. (3) Research of the islanding function of the PV system as the backup power supply was evaluated when blacking out. (NEDO)

Analysis for probability of irradiance fluctuation; Nissha hendo kakuritsu no bunseki

Energy Technology Data Exchange (ETDEWEB)

Minowa, J; Kurokawa, K [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K; Sakuta, K [Electrochemical Laboratory, Tsukuba (Japan)

1996-10-27

Distribution of probabilities of solar radiation fluctuation was examined to learn the fluctuation in photovoltaic power generation efficiency for the purpose of improving on the generation system. The measuring setup comprised one base station and nine terminal stations. The terminal stations were arrayed in lattice so that a 4km{times}4km-large area would be covered. The standard deviation in solar radiation fluctuation at an observation spot ANNE stayed constant at approximately 0.1kW/m{sup 2} at all observation hours. In the vicinity of a clearness index range of 0.5-0.6 (a higher index showing a clearer weather) in the daytime, the index fluctuated very much, predicting a half-clear sky with scattered cloud. In the range of 0.2-0.3, fluctuation was small. In the range of 0.6-0.7, fluctuation was small and solar radiation was stable under the clear sky. The scope of fluctuation in the areal average is smaller than that in the average at each of the terminal stations, which is explained by the even-out effect. This means that, if multiple PV systems concentratedly introduced into one region are appropriately coordinated, the outputs from the individual PV systems that are naturally inconsistent are evened out and that the reliability of the network as a whole is consequently enhanced. 5 refs., 7 figs., 1 tab.

Project subsidized by the Sunshine Project in fiscal 1982. Report on achievements in the project commissioned from NEDO - research and development on return of low-temperature hot water (simulated return test and a demonstration return test); 1982 nendo teion nessui kangen ni kansuru kenkyu kaihatsu seika hokokusho. Kangen mogi shiken kangen jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Tests and researches were performed with an objective to elucidate a decaying mechanism of return wells when low-temperature hot water utilized for geothermal binary power generation is returned underground. This paper reports the achievements in fiscal 1982. For the simulated return testing equipment, the hot water supply line was changed, a supply line was newly installed for a water flowing test on hot water in the Hacchobara area, flow rate measuring lines for each system were newly installed, and the pressure detecting locations were changed. In the fundamental tests on the simulated return test, experimental researches were carried out on the following items: production of silica scale from geothermal water, solubility of silica acid, effect of pH on polymerization of silica acid, induction time in the polymerization process of silica acid, sizes of poly-silica acid particles in geothermal water, production of poly-silica acid due to temperature drop, oversaturation degree of mono-silica acid, and scale deposition. In the simulated return test, temperature of a simulated column reproducing the return ground bed, particle sizes, and hot water properties were used as the parameters for the test conducted. As a result, the decay in return wells was estimated to be governed predominantly by chemical deposition of the scales. (NEDO)

Weightless environment simulation test; Mujuryo simulation shiken

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, K.; Yamamoto, T.; Kato, F. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1997-07-20

Kawasaki Heavy Industries, Ltd., delivered a Weightless Environment Test System (WETS) to National Space Development Agency of Japan in 1994. This system creates a weightless environment similar to that in space by balancing gravity and buoyancy in the water, and is constituted of a large water tank, facilities to supply air and cooling water to space suits worn in the water, etc. In this report, a weightless environment simulation test and the facilities to supply air and cooling water are described. In the weightless environment simulation test, the astronaut to undergo tests and training wears a space suit quite similar to the suit worn on the orbit, and performs EVA/IVA (extravehicular activities/intravehicular activities) around a JEM (Japanese Experimental Module) mockup installed in the water verifying JEM design specifications, preparing manuals for operations on the orbit, or receives basic space-related drill and training. An EVA weightless environment simulation test No. 3 was accomplished with success in January, 1997, when the supply of breathing water and cooling water to the space suit, etc., were carried out with safety and reliability. 2 refs., 8 figs., 2 tabs.

Report on technological survey in fiscal 1999. Demonstration test for smoothing grid interconnection (Collection of information by surveys in overseas countries); 1999 nendo keito renkei enkatsuka jissho shiken chosa hokokusho. Kaigai chosa ni yoru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys were performed on the institutional aspects of establishment and operation of grid interconnection guidelines in the countries advanced in introduction of discrete power supply systems. The survey items for America include: (1) summary of the status related to grid interconnection, (2) grid interconnection process, (3) methods for paying expenses for increasing power transmission facilities by means of grid interconnection, (4) dispute processing, (5) information release, and (6) software. The survey items for England, Germany, and France include: (1) summary of electricity business, (2) regulation patterns in electricity business, (3) summary of grid operating organizations, (4) connection to grid interconnection systems, and (5) the future liberalization programs. America is establishing standards for grid interconnection in discrete power supplies including photovoltaic power generation and energy storage under SCC21 of IEEE, whose conclusion will be drawn in the end of 2000. The Energy Department has an intention to give the standards the legal bases to operate them under unified requirements. Germany, England and France have all established standards for operating the grid interconnection. Market liberalization for electric power retailing is advancing in the order of America, England, Germany, and France. (NEDO)

Verification test for an electric vehicle using capacitor-battery series connection for battery load levelling; Denchi no fuka heijunka no tame no kyapashita to denchi no chokuretsu setsuzoku hoshiki wo saiyoshita denki jidosha no jissho shiken

Energy Technology Data Exchange (ETDEWEB)

Miyaoka, K.; Takehara, J.; Kato, S. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

1998-03-25

For the prolongation of the distance that an electric vehicle (EV) can cover on a single charge and of the service life of the EV battery unit, a system is developed, in which the battery unit and the capacitor unit are connected in series for the levelling-off of battery peak loads, and the system is tested aboard a running real vehicle. Installed on the real vehicle is a battery unit that is a series connection of 20 12V-38Ah seal-type lead-acid batteries, each battery consisting of two cells connected in parallel. Driving the vehicle is a DC brushless motor capable of a maximum operation of 9000rpm. Also installed is a capacitor unit that is a parallel connection of 40 2.3V-1800F capacitors, each capacitor consisting of two capacitors connected in parallel. Findings are described below. In a 0-400m acceleration test, 22.5 seconds is recorded with the capacitor unit in operation, meaning an improvement of 0.7 seconds. The maximum speed remains unchanged at 110km/h, which agrees with the pre-calculated value. Although the battery peak load reduction rate in a 15-mode drive pattern marks 23%, the distances covered on a single charge in this drive pattern turn out to be almost the same whether the capacitor unit is in operation or not. 3 refs., 15 figs., 3 tabs.

Report on technological survey in fiscal 1998. Demonstration test for smoothing grid interconnection (Collection of information by surveys in overseas countries); 1998 nendo keito renkei enkatsuka jissho shiken chosa hokokusho. Kaigai chosa ni yoru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Surveys were performed on the institutional aspects of establishment and operation of grid interconnection guidelines in the countries advanced in introduction of discrete power supply systems, namely, England, Ireland, Italy and the United States, as well as on the simulation technologies to realize them technically. In England, the power transmission systems (controller: NGO) and the power distribution systems (controller: PES) are separated, to which grid interconnection operating regulations are provided respectively. Single operation of generators connected to the power distribution system is not permitted substantially. In Ireland, the power transmission and distribution functions are separated, but are in the transition stage. Interconnection, if requested, cannot be rejected except for a case that the interconnection is impossible. Italy has the condition similar to that in Ireland, where no small generators are not permitted of independent operation. America has not unified the operating regulations for grid interconnection, and has apprehension in the independent operation, but no countermeasures have been given. In the simulation technologies, surveys were made on PSS/E, EUROSTAG, and SICRE. The PSS/E is the standard software in America for the current and stability analysis. (NEDO)

FY 1999 report on the results of the verification study on the alkali recovery process of the non-wood pulp/paper manufacturing industry; 1999 nendo seika hokokusho. Hi-mokuzai parupu seishi sangyo arukari kaishu purosesu ni kakawaru jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to energy conservation and environmental improvement in China, a joint verification study with China was made of a system for alkali recovery and heat recovery by effectively extracting/concentrating/burning black liquid in non-wood pulp/paper manufacturing plants in China, and the FY 1999 results were reported. Concretely, in the plan, an alkali recovery plant is to be constructed in Shandong Province to verify energy conservation and reduction in environmental loads. In the element study and the study of the related technology, an investigational study was made of the performance of waste water treatment facilities of paper manufacturing plants in China. Study was further made of the effect of desiliconizing agent on freeness and the method for treatment of waste water at the middle stage. As to the system design/manufacture, the basic design (material balance, heat balance, PID, layout, specifications, etc.) and detailed design were finished based on articles upon the technology to be adopted to facilities for verification and the basic design. Besides, the following were carried out: survey/selection of makers, order for all equipment, management of the jobs to be done by makers, etc. Equipment was sent in to the site. (NEDO)

Fiscal 1995 survey of promotion of the geothermal development. Report on a usage feasibility test of a small scale geothermal binary cycle power generation system; 1995 nendo chinetsu kaihatsu sokushin chosa. Chusho chinetsu binary hatsuden system jissho shiken hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In this survey, studies for popularization and practical utilization of small and medium size geothermal binary cycle power systems which assesses low and medium temperature geothermal resources were conducted, and studies for development of the system to be introduced for practical use and for promotion of the popularization were made. A study was carried out of preconditions and various conditions of a demonstrative test plant (100kW class, 500kW class) in view of the initial cost of the actual plant, and an analysis was made of the power generation cost. Acceptability of the demonstrative test plant (100kW class) was examined to analyze problems on the introduction. A thermodynamic analysis was made of the output of geothermal binary cycle power generation. Analysis/evaluation of the results of the 100kW demonstrative test plant were carried out in view of the operation results of the plant of the same kind, and checks/reviews were conducted of performance and reliability of the system, equipment simplification, etc. Inspection of the system was made in the stage of design/manufacture of the 500kW demonstrative test plant. Concerning the spread/expansion of the system, studied were multiple stage geothermal utilization and PR promotion method. 14 refs., 62 figs., 55 tabs.

Fiscal 2000 report on result of R and D of nonmetallic material recycling promotion technology (demonstration test and research, total system technology); 2000 nendo hitetsu kinzokukei sozai recycle sokushin gijutsu kenkyu kaihatsu seika hokokusho. Jissho shiken kenkyu, total system gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

R and D was conducted on advanced recycling technology for aluminum and base metal/rare metal based materials, with fiscal 2000 results compiled. In the research of aluminum recycling technology, on a continuous fractional crystallization process and a purification by zinc removal process, the existing facilities for each demonstrated that they could simulate an aluminum scrap melting process capacity of 1,000 t/month, with a series of initial conditions determined. In the research of total system technology, combined test facilities were completed in which a purification process and a melt cleaning process were integrated. In the research of the recycling technology for base metal/rare metal based materials, a test was carried out by demonstrative facilities, with the aim of establishing copper regeneration technology in which high grade copper is produced using metal/resin based scraps such as shredder dust of automobiles as the materials. In structuring the total system technology, a preliminary survey and environmental load measures were carried out toward the practicability of a comprehensive copper metal collection recycling system. (NEDO)

Earthquake-proof test of the bookshelf; Shoka no taishinsei shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

The seismic fragility testing was carried out on the bookshelf of 2 types 4 bodies submitted from the Co.,Ltd. primary steel industry place. (1) The vibration testing by seismic wave. The excitation by the Hyogo-ken Nanbu Earthquake wave is carried out. The following are examined: Behavior of test specimen for seismic wave, degree of the damage, response speed. (2) The sweep test. The sweep excitation of the sine wave in which the frequency automatically decreases is carried out, while the acceleration is fixedly kept. The following are examined: Behavior of test specimen, degree of the damage, response speed, and resonance point. (NEDO)

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

Report on development of high-efficiency wastes power generation technology in fiscal 1998. 1. Development of component technology, and demonstration test of a pilot plant; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Yoso gijutsu kaihatsu (pilot plant jissho shiken) (dai 1 bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A technology is developed to perform high-efficiency power generation by generating high-temperature and high-pressure steam stably by burning general wastes and combustible industrial wastes as fuel. This paper describes summary of the achievements in fiscal 1998. Corrosion tests were performed on over-heater materials under steam condition of 500 degrees C and 100 kg/cm{sup 2} by using a hot model. It was verified by the tests that the corrosion environment around an external heat exchanger is milder than that with an external stack. A circulation fluid bed was simulated from operation data, and a prospect was obtained on steam conditions required for the high-efficiency power generation. In order to elucidate the corrosion mechanism, discussions were given on deposited ash properties, corrosion characteristics and stress. Elucidation was made on a discharge chamber structure most suitable for removing dioxins and NOx by using a waste gas treatment process that uses plasma generated by discharge. A concept design was made. The economic effect of the system is equivalent to that of the activated carbon blow-in process, whereas a waste gas treatment system was nearly completed. As a result of the pilot plant test, the power generation efficiency is estimated to be 30% in a scale of 1200 tons per 24 hours. A demonstration test revealed that dioxin emission was far below the regulation value. An optimal system was also discussed. (NEDO)

Development of diagnosis and repair system for steelmaking refractories; Seikoyo taikabutsu no shindan hoshu gijutsu no kakuritsu

Energy Technology Data Exchange (ETDEWEB)

Aso, S.; Harada, S.; Tsutsui, Y. [Nippon Steel Corp., Tokyo (Japan)

1996-06-01

The latest measurement equipment and repair method were introduced into the work area of all refractories in the process of torpedo cars, hot metal preliminary treatment, hot metal pans, secondary refining, and cast pans so as to improve the cost of the newest advanced steelmaking refractories. As a result, the refractory cost could be reduced by 10%. This paper introduces the improvement in RH refractories and refractories for hot metal preliminary treatment. As for basic items, in addition to the visual observation, the thickness of refractories was quantified using equipment (laser profile meter, thermotracer, and NS sensor) for the furnace stop in the minimum remaining length. An ITV was also installed in the facilities where the visual check is difficult to carry out. Repair is mainly done by spraying. A thermal spraying repair method with high durability was used for the repair. A method that relieves a thermal shock was used for preheating. Moreover, measures that make the temperature gradient in the thickness direction uniform by using newly developed microwave drying equipment were taken for drying of unburned refractories. 4 refs., 13 figs., 2 tabs.

Research and development of photovoltaic power system; Taiyoko hatsuden system no jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result due to correction coefficient for the solar cell conversion efficiency; the inclined face insolation results in less by about 7% than the planned value, and the transmittable power amount less by about 14% in total; the load power amount is less by about 7% than the planned value; and the balance supplementing power factor increases by about 4%. 5 figs., 2 tabs.

Experimentation to seek the local speciality in kWh of P.V. system, and a study of its measuring method and instruments and apparatus; Taiyoko hatsuden system no jibetsu hatsudenryo no chiiki tokusei wo motomeru jissho shiken narabini, sono sokutei kansoku no hoho kiki ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Anno, T.

1997-11-25

Introduced in this paper are some problems that the author encounters in relation with a 2.6kW photovoltaic power generation system installed at the author`s residence for the purpose of measuring the hourly amounts of generated power. Giving rise to questions in the inverter and the control system are the conversion efficiency under a partial load, the scope of little amounts that are omitted, the maximum power point tracking system and its performance, etc. The author wants to learn how to land on an appropriate conductor thickness and to know the special specifications if any for heavy-snow regions and their effect. Much has been learned from presenters, moderators, and participants at scientific events and through private talks. Although it seems that there exists some relationship between the maximum power point tracking system and the diameter of conductors suitable for the system, yet the manufacturers fail to give clear-cut answers. The author thinks that end-users find many black box-like parts in the system, which the author leaves uncared for now for later study. It is learned that there is no specification intended exclusively for heavy-snow regions. The author`s system is in operation with hourly output recording and data accumulation started. 2 figs.

Pulse excitation experiment of a superconducting generator; chodendo hatsudenki no parusu reiki shiken

Energy Technology Data Exchange (ETDEWEB)

Miyaike, K.; Iimura, T.; Nishimura, M.; Arata, M.; Takabatake, M. [Toshiba Ltd., Tokyo (Japan); Yamada, M.; Kanamori, Y.; Hasegawa, K. [Kansai Electric Power Co., Inc., Osaka (Japan)

1999-11-10

Efficiency improvement, improvement in the stability of electric power system it is miniaturization and weight reduction can be expected in comparison with the traditional-model generator superconducting generator. We produce the small superconducting generator for the experiment experimentally, and performance characteristics verification of the generator is carried out experimentally. This time, pulse excitation test of the superconducting generator was carried out, and the ac loss of the conductor by the pulse excitation investigated the effect on the quenching current. (NEDO)

Demonstration of energy-saving construction works; Shoshigenka wo mezashita kenchiku koji no jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, T.; Yamagishi, M.; Kakimi, S. [Chubu Electric Power Co. Inc., Nagoya (Japan)

1997-11-01

Studies are conducted to promote energy-saving in construction works as part of environment protection programs. The first phase is for survey and analysis works for energy-saving in the current building design and construction works, and for processes, procedures and materials in model works (construction of sub-stations). The second phase is for studying energy-saving designs, materials and procedures, which are applied to model works, to assess their energy-saving effects , costs and applicability. The horizontally developed samples are prepared for the future development, based on the `continuous improvement of environment-management systems by establishing the PDCA cycles,` which is one of the basic requirements of the ISO14001 (environment management system). These efforts have reduced CO2 emissions associated with the manufacture of construction materials by 20%, mixed wastes by 45%, and plywood frame requirement by 70%. It is also confirmed that they can be realized at only around 3% higher cost. 9 refs., 10 figs., 3 tabs.

Actual proof study of energy autonomous house; Energy jiritsu house no jissho jikken. 1

Energy Technology Data Exchange (ETDEWEB)

Masuzawa, O; Masuzawa, C

1997-11-25

A discussion was given on an `energy autonomous house` which utilizes more effectively photovoltaic power generation, solar heat and light in designing a wooden house to be built by using the conventional construction method. According to the plan, photovoltaic power generation modules and heat collectors are installed superimposed on a roof facing south. Heat-collected air is sent below the floor and the heat is stored in the concrete in winter, utilized as the floor heating type room heater. The hot air is used for hot water supply in other seasons. The building is of two stories with a total area of 118 m {sup 2}, and the photovoltaic generation capacity is 3.48 kW. The photovoltaic generation amount was calculated from insolation forecasted by the AMEDAS system, and energy balance of this house was estimated. The result therefrom may be summarized as follows: total energy supplied reached 11.6 Gcal, signifying that about 10.8% of the energy irradiated onto the building is utilized; ratio of the photovoltaic and solar heat utilization is 27% versus 73%; and energy consumption in this house was estimated and calculated from actual results, airtightness and adiabatic performance of old houses, whereas the energy autonomous rate has reached 92.8%. 5 refs., 2 figs., 8 tabs.

Joint verification project on environmentally friendly coal utilization systems. Joint verification project on the water-saving coal preparation system; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

In this verification project, clean technology which should be spread in China was verified and the base structure for its spread was prepared for the purpose of controlling emissions of environmental pollutants associated with the coal utilization in China and of contributing to secure energy acquisition of Japan. As joint verification projects, a general rehabilitation type coal preparation system was installed in the Wangfenggang coal preparation plant, and a central control coal preparation system was installed in the Qingtan coal preparation plant. In the former, a system is verified in which optimum operation, water-saving, high quality, and heightening of efficiency can be obtained by introducing two computing systems for operation control and quality control, various measuring instruments, and analyzers to coal preparation plants where analog operation is conducted helped by Russia and Porland and have problems about quality control. In the latter, a central control system achieving water saving is verified by introducing rapid ash meters, scales, desitometers and computers to coal preparation plants having zigzag or heavy-fluid cyclon and connecting various kinds of information through network. For fiscal 1994, investigation and study were conducted. 51 figs., 9 tabs.

FY 1992 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Developmental study of a methanol engine system for power generation; 1992 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Hatsuden you metanoru enjin system no kaihatsu kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

For the purpose of establishing the methanol engine technology for promotion of methanol introduction to oil-fired power plant, an experimental study was made, and the FY 1992 results were summarized. In the study of technology development, the following were carried out: evaluation of durability of multi glow plug and development of high-durability glow plug, confirmation of potentiality of the laser ignition system by element evaluation test, evaluation/improvement of durability of the injection system and development of injection pump for the actual machine, trial manufacture of the 2-stage injection system and confirmation of characteristics, study of improvement in ignitability/combustion state by optimization of the temperature of glow plug, compression rate, etc., evaluation of durability of combustion chamber, etc. by the heat load measuring test and heat balance, etc. As a result of the engine test, the pump housing stayed favorable without damage in the use of about 20,000h, plunger assembly did in the use of about 4,500h, and valve assembly did in the use of about 20,000h. As to the manufacture of the actual machine, a prototype was designed/manufactured of a 500kW class direct injection 4 cycle supercharging 6 cylinder methanol engine. (NEDO)

Study on application of single-crystal ice `Kurobe ice column` to high-speed skating rinks. Demonstration test result at Olympic memorial arena `M wave` in Nagano city; Tankesshohyo `Kurobe no hyojun` no kosoku skate link eno tekiyosei kenkyu. Naganoshi olympic kinen arina `Emu Wave` deno jissho shiken kekka

Energy Technology Data Exchange (ETDEWEB)

Iwasaki, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

1999-06-10

For high-speed low-friction skating rinks, research was made on sticking artificial ice columns (ice bamboo shoot). The ice columns were fabricated with the ice column production equipment equipped with 4-line water droplet dropping devices which were installed at intervals of 0.3m on both sides of a pathway of 200m long, 2.6m wide and 1.8m high in the lateral adit of Kurobegawa No.4 hydroelectric power station. The grown ice columns were processed for high-speed skating rinks through cutting, confirmation of single crystal and crystal orientation, slicing for every 7mm thickness and packaging. The ice columns were spread all over the rink while sliding them to prevent mixing of bubbles after spraying distilled water of nearly 25 degreesC onto base ices. In addition, hot water of nearly 40 degreesC was sprayed to produce the final ice rink of 30mm thick by nearly 5mm a day. The dynamic friction coefficient of the ice column rink reduced to 0.0038 by nearly 16% as compared with 0.0045 of conventional rinks. (NEDO)

Report on joint research in fiscal 1999. Research and development of technology to promote recycling of non-ferrous metal materials (Report on achievement in researches of demonstration tests and total system technology); 1999 nendo hitetsu kinzokukei sozai recycle sokushin gijutsu seika hokokusho. Jissho shiken kenkyu, total system gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Development has been in progress on promotion of recycling the non-ferrous metal materials, particularly aluminum, base metals and rare metals (such as copper). For aluminum, researches were made on demonstration of the crystal separation process, vacuum deposition process, molten scrap cleaning technology, and residual dross utilizing technology. In the crystal separation process to remove Fe and Si, and the vacuum deposition process to remove Zn, trial operation and adjustments were performed on the demonstration and testing facilities, making simulation in the scale of 1000 tons a month possible. In the molten scrap cleaning technology, discussions were given on a method to install on the trough a filter permitting micro inclusions in the molten scrap, but no results as have been expected were obtained. The residual dross was used on a trial basis for applications such as road aggregate and refractory materials. In the exhaust treatment, it was recognized effective that activated carbon and slaked lime are used simultaneously to remove hydrochloric acid and dioxins. In developing a technology to regenerate high-grade copper from sludge dust, discussions were given on design, fabrication, and trial operation of the demonstration facilities, partly by using a demonstration plant, with regard to the five related technologies including a technology for high precision refining of scraps, and high-speed metal melting technology. (NEDO)

Wind tunnel test on PC cable-stayed bridge; PC shachokyo no taifu seino shiken

Energy Technology Data Exchange (ETDEWEB)

Kubo, Y. [Kyushu Inst. of Technology, Kitakyushu (Japan). Faculty of Engineering

1997-05-30

This paper describes the wind tunnel test on a PC cable-stayed bridge. The aerodynamic force that acts on a building is represented by the drag that works in the wind direction, the lift that works perpendicularly to the wind direction, and the aerodynamic moment that causes rotation. In the measurement of wind load, a girder is partially extracted in the wind tunnel and set in a three-component balance, and the drag, lift, and aerodynamic moment are measured using a strain meter while blowing the wind. In a wind tunnel experiment, the similarity on Reynolds number, field number, rigidity, hydraulic force, structural attenuation, and reduced wind velocity is required. However, the wind velocity in the actual bridge uses the same air as that in an experiment. The similarity rule on the Reynolds is not thus satisfied. It is necessary to cause no self-excited vibration (galloping and flutter) as wind-resistant performance and suppress the eddy excitation to less than the allowable amplitude. Moreover, the three-dimensional experiment using an elastic model is conducted in addition to the two-dimensional experiment using a rigid model. In the three-dimensional experiment, various vibration modes that occur in the actual bridge appear. 12 refs., 15 figs.

Development and demonstration of optical polarization controller; Hikari henpa seigyo sochi no kaihatsu to jissho

Energy Technology Data Exchange (ETDEWEB)

Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1997-04-01

If fiber transmission light can be controlled in a stabilized polarization state, realization of coherent optical communication is anticipated. In the case of adopting it to OPGW, however, it is necessary to compensate high speed polarization variation caused by lightning strike. But this was difficult in the conventional method. Accordingly, a high speed polarization control method was proposed which uses an electric effect of lithium niobate (LN) crystals. In the study, a polarization control unit was manufactured based on the method proposed and the performance was demonstrated. As a result of measuring output light with input light changed in every state of polarization, the object horizontal polarization component obtained a stabilized light intensity at {+-}0.1dB, and a light intensity of the component slipped out of the horizontal polarization was suppressed under -20dB. To cope with the polarization variation by lightning strike, it is necessary to make the control delay 10{mu}sec or below, and improvement in processing unit, etc. may make it possible since LN crystals respond below 1{mu}sec. High speed control of the infinitely continuing arbitrary polarization variation became possible. 14 refs., 19 figs.

Survey for development feasibility in fiscal 1999 investigation of geothermal development and promotion. Evaluation report on practicability technology survey SWD method (Evaluation report concerning verification test); 1999 nendo chinetsu kaihatsu sokushin chosa no uchi kaihatsu kanosei chosa. Jitsuyoka gijutsu chosa SWD ho hyoka hokokusho (jissho shiken ni kakawaru hyoka hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

An evaluation test was conducted on SWD (Seismic While Drilling) method as a part of the investigation of geothermal development and promotion. The test was implemented at the time of drilling of N11-MD-3 well in the northeast base area of Busadake, Hokkaido. The test items were such as verification of direct waves propagating from a bit to the surface, identification of signals passing through a fault zone using direct waves and reflected waves, estimation of distance between a fault and a bent zone, and grasping the direction of signal propagation at the time of inclined drilling. As a result of the experiments and studies, following conclusions were obtained. Reflected waves extracted are not necessarily limited to those from a reflection area from which the shape of a fault can be grasped; unless there is a clear reflection area that can be picked up on the surface near a fault, the application of this method is not effective. In an analysis using direct waves, it was possible to obtain an inclined angle of a fault plane from the estimation of velocity structure, propagation route, and assumption of the shape of the fault plane and, therefore, to grasp the shape of the fault. Obtaining reference data is essential for identifying bit signals. (NEDO)

ASKA STOL research aircraft flight tests and evaluation. STOL jikkenki Asuka'' no hiko shiken kekka

Energy Technology Data Exchange (ETDEWEB)

Kuriyama, M; Inoue, T; Tobinaga, Y; Tsuji, H [Kawasaki Heavy Industries, Ltd., Tokyo (Japan)

1991-07-20

The present report evaluated the powered high-lift device (PHLD) distance of upper surface blowing (USB) system, basing the materialization of short distance take-off and landing (STOL) performance, one of the main flight test purposes by the Aska'', quiet STOL research aircraft, which evaluation was then added with reporting its flight test result to cover several topics. As prototypical, a C-1 tactical transport aircraft produced by Kawasaki Heavy Industries was modified to the aska'' together with the following change in design for the STOL flight test: Adoption was made of a PHLD of USB system where the wing surface was mounted with four turbofan jet engines thereon. Application was made of a boundary layer control (BLC) to the main wing leading edge and aileron. Mounting was made of a stability and control augmentation system (SCAS) using a triple system digital computer. Fitting was made of a vortex generator for the prevention from peeling by jet exhaust. As a result of flight test, the recorded distance was confirmed to be 1580ft in landing and 1670ft in take-off. 5 refs., 15 figs., 2 tabs.

Fiscal 1995 survey report on the environmentally friendly type coal utilization system joint demonstration project. Water-saving coal preparation system joint demonstration project; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This project makes demonstration of clean coal technology (CCT) in China and preparation for the base of its spread, controlled environmental pollution due to the coal use by the countries concerned, and contributes to stably secure energy of Japan. The paper made analog operation in the 1960s-1970s, supported by Russia and Poland, introduced two computer systems for operational control and quality control, densimeter, level meter, flow meter and analyzer to coal preparation plants having problems on productivity and quality control, made the optimum operational diagnosis for the plants, and at the same time, demonstrated the comprehensive rehabilitation type system by which water saving, high quality and high effectiveness are obtained. Various types of sensors such as rapid ash meter, scale and densitometer and computers are introduced to coal preparation plants which were recently constructed in China, have jig or heavy liquid cyclone as main preparation equipment and conducts operational control. There, the central control system was demonstrated in which various information collected in the central operation room and in-site equipment is combined by network for high-grade data processing and water saving is achieved. 50 figs., 11 tabs.

General report of entrustment investigation for demonstration tests of turnover from oil to methanol in the thermal power plants in fiscal 1995. Total assessment of methanol using power generation technology; 1995 nendo sekiyu karyoku hatsudensho methanol tenkan nado jissho shiken itaku gyomu hokokusho sokatsu hokokusho. Methanol riyo hatsuden gijutsu sogo hyoka chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To promote the introduction of methanol fuel into the thermal power plants, total assessment was provided. For calculating the methanol production cost, the plant was assumed to be constructed in the Southeast Asia or Middle East. Two methods, i.e., steam reforming and gaseous phase fluid methods, were investigated. Since the price of natural gas is low in the Middle East, the methanol production cost by the gaseous phase fluid method is estimated to be about 1.5 yen per thousand kcal. The transportation cost can be reduced into one-half to one-third of current cost using a large-scale tanker. Although the heating value of methanol per weight is lower than that of LNG, the volume flow of methanol is similar to that of LNG due to its low specific gravity. Conceptual designs were conducted for some power generation systems, such as gas turbine of combined cycle, diesel engine, and fuel cell. The power generation cost was estimated to be 8 to 9 yen per kWh, which depends on the receiving price of methanol. It is nearly equivalent to that of LNG combined cycle power generation. There are no problems of air pollution and ash disposal. When considering the long-term security of energy sources, the use of methanol would be one of the selections as utilization of natural gas. 6 refs., 33 figs., 25 tabs.

FY1995 development of micromachine technology based on insects; 1995 nendo konchu wo kihan to suru micromachine gijutsu no kakuritsu to jitsuyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

If we develop micromachines by reducing simply the size of conventional mechanical systems, we cannot get sufficient performances of them because of scale-effect. Small natural creatures, insects, have very good structures and functions reasonable for their small size. In this research, basic characteristics of sensors, actuators, information processing functions, etc. of insects are studied and artificial systems similar to them are developed for industrial application. (1) Compound eyes: Insect compound eyes is the visual sensor which is composed of microlenses which are distributed three-dimensionally, receptors which vibrate with small amplitude around an optical axis and neural networks. In this research, the large scale model (several centimeters sized) of insect compound eyes has been developed. (2) Pheromone sensor: Pheromone gas sensor has been made of real male silkworm moth antenae. This sensor has been proved to work well as the female pheromone detector. This sensor was installed at the nose part of a wheeled mobile robot and this robot was observed to act like a real silkworm moth subjected to female pheromone stream. (3) Electrostatic microactuator: Generally speaking, high voltage(higher than 100V) electric power is necessary to actuate the electrostatic actuator. It was considered to be impossible to actuate them directly from CMOS. In this research, a new electrostatic actuator which can be actuated with less than 10V voltage can cause a fairly large displacement. (4) Hydraulic actuator: For micromachines, hydraulic pressure will be applicable for actuation. Structures may be simple and scale effect may give an advantageous characteristics for microsize. A butterfly-type flying robot was developed and it flied up along a vertical bar. (NEDO)

Performance test of solar energy distillation system; Taiyonetsu riyo kaisui tansuika system no zosui seino shiken

Energy Technology Data Exchange (ETDEWEB)

Kawahara, T; Toyoshima, Y [Keio University, Tokyo (Japan); Narasaki, Y; Kamiya, I [Ebara Corp., Tokyo (Japan); Sato, H [Keio University, Tokyo (Japan). Faculty of Science and Technology

1997-11-25

In order to develop a seawater desalination equipment utilizing solar heat, a performance test was performed on a three-stage solar heat vacuum distiller. The equipment can evaporate and condense water at low temperatures by reducing the pressure in a distilling section. Solar heat is collected by a heat collecting plate, by which water as the working fluid is evaporated and moved to a heat conducting section in an evaporation pipe in a state of steam. The steam is condensed in a low-temperature heat conducting pipe, the heat is released outside the heat conducting pipe, and seawater is evaporated under low pressure condition. The working fluid is circulated for repetitive use. Solar cells are used as a motive power source for a vacuum pump, hence the system is self-sustainable even if installed in a desert area and the like places. The construction is simple, highly durable, and easy in maintenance. The system has high water producing performance, uses no harmful substances whatsoever such as fluorocarbons, and is a friendly system to the global environment. Because of evaporation at low temperatures, heat loss to the surroundings and sensible heat due to temperature rise are small, and the system response is quick. The solar heat can be utilized more effectively as multiple effects. When a heat collecting plate of 7.76 m {sup 2} was used, maximum yield of 105.45 kg/day was obtained. The system`s distillation efficiency is higher than other types of solar heat utilizing distillers. 7 refs., 5 figs.

Test and evaluation on safety relating to biotechnology; Biotechnology ni kansuru anzensei no shiken to hyoka

Energy Technology Data Exchange (ETDEWEB)

Okada, M. [Bio-Oriented Technology Research Advancement Inst., Saitama (Japan)

1996-09-05

This paper describes the current status and how works are being carried out on safety tests and evaluation of gene recombinants in plants and microorganisms. In the field of plants, Flavr Savr tomato which has been improved in fully ripe fruit distribution and keeping quality was commercialized as the world`s first recombinant food in May 1994 by Calgene, Inc. of America. Other vegetables, such as soybean, corn, potato, and pumpkin have been completed of all items of safety evaluation, and are approaching the commercialization phase. The safety evaluation system for living organisms created by using recombinant DNA technologies has been established internationally with regard to its general framework and contents based on accumulated knowledeges and experiences as a result of utilization of over twenty years. Industrial utilization guidelines for recombinants in Japan have been established in correspondence with the OECD recommendation in 1986. Experiments to verify recombinants to be safe in environment, and cultivation of the recombinants for utilization are performed based on the experimental guidelines and utilization guidelines. 15 refs., 1 fig., 5 tabs.

Fiscal 1999 report on results of joint demonstrative project for environmentally benign coal utilization system. Demonstrative project concerning coal preparation technology (China); 1999 nendo kankyo chowagata sekitan riyo system kyodo jissho jigyo seika hokokusho. Sentan gijutsu ni kakawaru jissho jigyo (Chugoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the demonstrative project for coal preparation technology, as a part of the measures against environmental pollution due to the structuring of demonstration and dissemination basis for clean coal technologies in China, The results for fiscal 1999 is reported. In the utilization of coal in China, a problem of urgency is the highly efficient selection and removal of sulfur contents in raw coal. Coal production in Chongquing City is yearly 30 million tons, of which 90% contains sulfur contents of 3% or higher. At Jinjia Colliery of Panjiang Coal and Electric Co. Ltd., Guizhou Province, a site for the present project, a number of coal seams are unsuitable for single utilization because of high sulfur contents. The coal preparation technologies to be introduced are expected to improve coal preparation efficiency and desulfurization ratio in terms of both the washability of raw coal and the accuracy of the coal washer. This is the third year of the project, with the following activities performed, namely, research/design, manufacturing/procurement of equipment, design for construction work, training of operators or the like, and documentation. The manufacturing and procurement are for such equipment as vacuum disk filter with accessories, waste water thickener, pressure filter for tailings with accessories, flocculant pump/piping, slurry tank/pump, high-shear mixer with accessories, and electric instrumentation. All the equipment arrived at the site in January, 2001. (NEDO)

Study on box shield tunneling method in trial field operation; Box shield koho jissho seko ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Tada, K.; Taniguchi, T. [Toda Corp., Tokyo, (Japan); Furukawa, K.; Nakagawa, K. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering

1997-03-20

This paper describes a rectangular section shield tunneling method as a part of developments of non-circular section shield tunneling methods. The non-circular shield is drawing attention because of need of excavation in small land available in urban areas and between congested existing structures, as well as reduction in the excavated soil amount. A full-scale machine was fabricated to perform a natural ground excavation experiment. The cutter units comprising two each of drum cutters and ring cutters were arranged above and below, by which two tunnels of 40 m long with a cross section of 2.85 m {times} 2.85 m were excavated. The natural ground was supported safely by holding mud water pressures at cutting points constant, thus stability of the cutting points was ensured. Back-filling has made complete filling of tail void (clearance between a segment and the ground) possible, resulting in suppression in conditional change of the surrounding ground. Attitude control has been performed properly as a result of correct selection of shield jacks and use of deflection jacks. Broken-type over-cutters were used to have constructed tunnels with curve radius of 80 and 100 m with high accuracy. Thrust and propulsion speed of the shield do not differ from those of circular shields. Possibilities of this construction method were verified. 8 refs., 26 figs., 2 tabs.

Wind tunnel investigation of an STOL aircraft model. STOL zenki mokei-fudo shiken. ; Engine nacelle keijo koka

Energy Technology Data Exchange (ETDEWEB)

1993-01-01

The nacelle shape of a mimic engine mounted on the wind tunnel test model for an STOL aircraft developed by the National Aerospace Laboratory has much larger length than in the nacelle of a scale reduced to 8% of an actual engine, and the shape below the nacelle is different. Therefore, in order to estimate the air force in the actual aircraft from the aerodynamic data obtained in a wind tunnel test, the data are corrected by using differences in aerodynamic loads (estimated values) applied on the mimic engine and the actual engine. For the purpose of discussing the reasonability of this correction, an 8%-scale flow through nacelle with the same shape as in the actual aircraft (the actual aircraft type) and a flow through nacelle for a wind tunnel testing model of the experimental STOL aircraft were fabricated and wind tunnel tests were performed. These results were compared with the corrected results of the mimic engine wind tunnel test. As a result, it was made clear that the force data have been corrected excessively, and the moments have been corrected considerably well. 7 refs., 32 figs., 7 tabs.

FY 1984 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential quantity supplied of overseas resource (Survey of the usability of methanol); 1984 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru riyo kanosei chosa) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

The paper studied a scenario of the demand for power generation use methanol in Japan by grasping the situation of the utilization of methanol as fuel in the world, studying a scenario of power supply and the positioning of methanol power generation in Japan, doing a trial calculation of the breakeven price of power generation use methanol, etc. As to the usability of power generation use methanol as fuel, in the use for the reformed gas turbine and fuel cell, there is a possibility of making up for the disadvantage in fuel price by future technical development. For the fuel conversion at existing coal-fired power plants and the application of methanol to combined cycle and newly-installed boiler, it is necessary to have a substantial drop in methanol price. Taking an advantage that methanol can be transported in small size and easily be stored, methanol can possibly be used as fuel for dispersed power sources. The potential demand for petroleum substituting methanol is estimated at approximately 25 million t/y, assuming it to be 1/2 of the petroleum consumption amount. The present methanol market in the world is not so large for quantity use as fuel, and for the introduction, therefore, it is necessary to secure flexibility in supply. (NEDO)

FY 1984 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential quantity supplied of overseas resource (Survey of the potential quantity supplied of methanol); 1984 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru kyokyu kano ryo chosa) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

Based on the results of the survey of the potential quantity supplied of overseas resource which was made from FY 1981 to FY 1983, the paper predicted the world methanol supply plan, changes in the oil situation, economical efficiency of methanol and the competitive power with petroleum products, etc., and studied the time of potential supply, areas of potential supply and supply potential of power generation use methanol during the period toward 2000. In case the comparatively low crude oil price is predicted due to the energy supply/demand (Scenario A), the supply potential of power generation use methanol in four projects on methanol production taken up as trial calculation example is considered very low. Even in case the comparatively high crude oil price is predicted (Scenario C), it is in 1989 that the methanol market price becomes equivalent in heat quantity to the crude oil price. It is difficult to expect the potential before 1989. In case of the intermediate case between Scenario A and Scenario C (Scenario B), it is in 1993 that the methanol price becomes equivalent in heat quantity to the crude oil price. It is difficult to expect the potential before 1993. (NEDO)

FY 1991 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Feasibility study of a new system for the stabilized supply of fuel use methanol; 1991 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Nenryo you metanoru kyokyu antei ka no tameno shin system no kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

As a part of the project on the demonstration test on the methanol conversion at oil-fired power plant, feasibility study was made of a new system for methanol production by using abundant hydraulic power energy overseas and by combining water electrolysis and coal gasification technology, and the FY 1991 results were summarized. As a result of the survey, the following were selected as water electrolysis facilities: high efficiency/high current density/simplification system and solid polyelectrolyte electrolysis system with a high purity of hydrogen gas. As the coal gasifier, the oxygen blown furnace was selected which has a high carbon utilization factor, is able to gasify coal at high pressure, has no unnecessary N{sub 2}, and is being used in the integrated coal gasification combined cycle power system. As methanol synthesis facilities, the MGC/MHI method super converter was selected. Assuming the output of hydroelectric power generation to be 4,000MW, conceptual design of the optimum system was made. The methanol cost was estimated under the conditions written below: cost of hydroelectric power generation at site: 2-5 yen/kWh, coal unit price at site: 5,000-6,000 yen/t, transportation distance: 5,000-10,000 km. (NEDO)

FY 1982 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential supply amount of overseas resource (Survey of the potential supply amount of methanol); 1982 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Kaigai shigen kyokyu kano ryo chosa (Metanoru kyokyu kano ryo chosa) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-07-01

For the study of the potential supply amount of methanol as power generation use fuel, survey was conducted as case study on the following: Victorian brown coal of Australia, conversion of Arun natural gas to methanol at site in Indonesia, political/social/technical restrictions, supply scale, economical efficiency, etc. at the time of the supply to Japan. For the calculation of economical efficiency, it was assumed that the scale of methanol production was 5,000 t/d, that the plant operated years were 20 and that the price of acquisition of raw material was US$4-10/t in Victorian brown coal and US$1-4/t in Arun natural gas. As a result of the study, in the case of natural gas base methanol, the CIF Japan is lower than CIF prices of LNG and crude oil in case the price of acquisition of raw material is US$1/t, but is higher than those in case the price is US$2/t. In the case of brown coal base methanol, it was found that the CIF Japan could not be lower than CIF prices of LNG and crude oil even in case the price of acquisition of raw material is US$4/t, which is the lowest. (NEDO)

Study on application of single-crystal ice 'Kurobe ice column' to high-speed skating rinks. Demonstration test result at Olympic memorial arena 'M wave' in Nagano city. Tankesshohyo 'Kurobe no hyojun' no kosoku skate link eno tekiyosei kenkyu. Naganoshi olympic kinen arina 'Emu Wave' deno jissho shiken kekka

Energy Technology Data Exchange (ETDEWEB)

Iwasaki, M. (Kansai Electric Power Co. Inc., Osaka (Japan))

1999-06-10

For high-speed low-friction skating rinks, research was made on sticking artificial ice columns (ice bamboo shoot). The ice columns were fabricated with the ice column production equipment equipped with 4-line water droplet dropping devices which were installed at intervals of 0.3m on both sides of a pathway of 200m long, 2.6m wide and 1.8m high in the lateral adit of Kurobegawa No.4 hydroelectric power station. The grown ice columns were processed for high-speed skating rinks through cutting, confirmation of single crystal and crystal orientation, slicing for every 7mm thickness and packaging. The ice columns were spread all over the rink while sliding them to prevent mixing of bubbles after spraying distilled water of nearly 25 degreesC onto base ices. In addition, hot water of nearly 40 degreesC was sprayed to produce the final ice rink of 30mm thick by nearly 5mm a day. The dynamic friction coefficient of the ice column rink reduced to 0.0038 by nearly 16% as compared with 0.0045 of conventional rinks. (NEDO)

FY 1992 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Feasibility study of a new system for the stabilized supply of fuel use methanol; 1992 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Nenryo you metanoru kyokyu antei ka no tameno shin system no kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

An investigational study was made of potentiality of a new system for methanol production by using abundant hydraulic power energy overseas and by combining water electrolysis and coal gasification technology, and the FY 1992 results were summarized. In this fiscal year, survey was made of the potential water power and coal in Malaysia, Canada and Brazil, and case study was also made. As a result of the study, the cost of methanol was 7.1 yen/10{sup 3}kcal in case of Malaysia, 8.6 yen/10{sup 3}kcal in case of Canada and 8.9 yen/10{sup 3}kcal in case of Brazil. It was found out that the cost was economically less advantageous as compared with the present methanol price of 3.0-5.5 yen/10{sup 3}kcal. In a comparison between the existing coal/oil/LNG thermal power generation and this system from viewpoints of the energy balance/CO2 emission amount, the energy balance of this system is worse than those of the above-mentioned power generation when adding the coal thrown, but the CO2 emission amount of the system was less than those of coal/oil thermal power generation. In conclusion, this system seems to be an effective means in the light of the promotion of development of the undeveloped hydraulic power, effective utilization of renewable energy and global environmental preservation. (NEDO)

Fiscal 2000 achievement report. International demonstrative development of photovoltaic power generation system (Demonstrative study on grid-connected photovoltaic power generation system in Thailand); 2000 nendo seika hokokusho. Taiyoko hatsuden system kokusai kyodo jissho kaihatsu - Taiyoko hatsuden keitou renkei system jissho kenkyu (Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-09-01

A demonstrative study was conducted in Thailand for grasping the effect on small electricity grids when several photovoltaic power generation systems, including AC modules, are connected to the grid. In fiscal 2000, surveys and studies were conducted about the data of the local power system, where to install the demonstrative system, and how to install the same, which were necessary for working out a basic design for Libong Island newly designated as the site for the demonstrative system. It was then concluded that the demonstrative system be a grid-connected 100 kW-level photovoltaic system comprising one main photovoltaic power station (85 kW), photovoltaic power systems for school buildings (3-6 kW, three schools), and AC modules (110 W, 10 locations). The manufacture of solar cell modules, grid-connected power conditioners, and measuring devices were completed. Civil engineering work and construction were under way on the site, including the construction of a management building, installation of concrete bases for solar cell arrays, construction of fences surrounding the site, and so forth. (NEDO)

Application of cytotoxicity test for toxic micropollutants. Saibo dokusei shiken ni yoru yugai kagaku busshitsu osen no hyoka

Energy Technology Data Exchange (ETDEWEB)

Utsumi, H; Hamada, A [Showa University, Tokyo (Japan). School of Pharmaceutical Science; Ono, Y [National Institute of Hygienic Sciences, Tokyo (Japan)

1992-10-01

Considerations were given from a viewpoint of assessing toxicity to human bodies on methods of assessing water pollutants and organisms, and applicability of cytotoxity test using cultured cells to water quality assessment. Biological assessment systems used for water environment may use tests using multicellular organisms, cells, or organelles in cells. The organism assessment method is intended mainly for assessing ecological effects, and a suitable method must be selected upon extrapolating it to human bodies. A toxicity parameter used most frequently in a cytotoxity test is the cell revival rate, and life and death are determined from liberation of enzymes in cells, or with color rejection tests and incorporation tests. There are a number of test specimens of raw tap water and its chlorine treatment condensate that show no mutagenicity but cytotoxity. Efficiencies of removal by means of mild chlorine treatment, fast filtration, and activated carbon adsorption vary greatly with cytotoxity and mutagenicity. Introducing the cytotoxity test is expected of further contributing to improving safety in water quality. 24 refs., 1 fig., 7 tabs.

Separation of unburned carbon from coal fly ash through froth flotation; Sekitanbai no shisshiki datsutanso gijutsu kaihatsu shiken

Energy Technology Data Exchange (ETDEWEB)

Miwa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Murakami, T [The Coal Mining Research Center, Japan, Tokyo (Japan)

1996-09-01

Coal ash tends to become containing more unburned carbon and porous substances depending on conditions of combustion, whose adverse effects to products due to water adsorbability, absorbability and color tones create obstacles in its utilization. Therefore, research and development works have been progressed on wet type carbon removing technology which is characterized in that coal is pulverized to preferable degrees and subjected to flotation. This paper reports the results obtained during fiscal 1995. The results may be summarized as follows: as a result of the comparison test on a column flotation machine and an FW type flotation machine of machine stirring type, the former machine showed better flotation efficiency; several methods were investigated on crushing as a treatment prior to flotation, whereas a mixer with greater circumferential speed and a homo mixer showed the highest efficiency; strength of the impact to the flotation efficiency was found to decrease in the order of pulp concentration > pretreatment time > collector addition ratio; and as a result of the evaluation on refined ash as a cement admixture and carbons as fuel, possibilities were found in them for practical application. 16 figs., 2 tabs.

Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

Fiscal 2000 report on the international joint verification of photovoltaic power generation system. Verification of hybrid system comprising photovoltaic power generation system and micro-hydroelectric power generation systems; 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho. Taiyoko micro suiryoku hybrid system jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

Research was conducted in Vietnam for the development of a hybrid system comprising a photovoltaic power generation system and a micro-hydroelectric power generation system. In verification test operation, data measurement had been under way for approximately 18 months since it was started in September 1999. The rate of days on which effective data were obtained throughout this period was 93.4%. Power generated by the micro-hydroelectric power generation system was 19.4kWh/d with so small a capacity factor of 3.2%. The capacity factor of the photovoltaic power generation system was again very small at 4.5% since the amount consumed by the load was as small as 131.0kWh/d. Weather data of solar radiation and precipitation were being collected smoothly. In the study of hybrid system optimization, the effect of inductor generator activation upon the inverter was taken up. In the study of capacity balance optimization between the constituent elements of the hybrid system, methodology was established and verified, and calculations were carried out. (NEDO)

Fiscal 2000 report on result of international joint demonstrative development of photovoltaic power generation system. Demonstrative research on photovoltaic power generation system interconnection system (Myanmar); 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu seika hokokusho. Taiyoko hatsuden keito renkei system jissho kenkyu (Myanmar)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Joint research was conducted with Myanmar on a photovoltaic power generation system interconnection system, for which fiscal 2000 results were described in this paper. Power generating facilities were set up consisting of 80kW photovoltaic, 40kW wind and 60kW diesel systems. With the photovoltaic and wind power generation connected to a small-scale power system as a ballast load, the system interconnection is formed through load adjusting equipment such as storage batteries. The hybrid system feeding is from 6 o'clock early in the morning until 23 late at night. The diesel power generation is free from restrictions. The operating method was set on system control (demand side management) by adjustment from the load side, with ballast load control employed that adjustably operates an ice machine load. The basic design was drafted in terms of a storage battery capacity of 1,000Ah and an ice machine load of 32kW. The daytime load was assumed to be 25% of the night load. On the equipment specifications set in this basic design, arrangement design was conducted for the equipment in the premises, making a land development plan and a basic construction plan including a temporary work site, construction steps, transportation and delivery of the equipment. Quantity of solar radiation and wind data were continuously observed. (NEDO)

Fiscal 2000 report on data of international joint demonstrative development of photovoltaic power generation system. Demonstrative research on photovoltaic power generation system interconnection system (Myanmar); 2000 nendo taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho. Taiyoko hatsuden keito renkei system jissho kenkyu (Myanmar) - shiryohen

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the fiscal 2000 report on research data of joint demonstrative development with Myanmar concerning photovoltaic power generation system interconnection system. The purpose is an operation research in the case where a small-scale electric power generation system in an remote island or the like in Japan is linked with a severely output-fluctuating power generation system using energy of nature such as photovoltaic and wind power generation. In particular, among the system control (demand side management) methods by adjustment from a loading side, ballast load control was employed that adjustably operates load of an ice machine for example. As the contents of the data, the quantity of solar radiation and wind velocity at the Chaungthar site were shown as meteorological observation data. In addition, a graph was made on the meteorological observation data at the Chaungthar and Letkhokekone sites. The paper also explains the final explanatory data for selecting the sites in implementing the demonstrative research. As to the operation method of the hybrid power generation system, assumption was made for the daytime load in four cases from 50% (30kW) to 0% (0kW) of the nighttime. Storage batteries and diesel generators were installed and used in combination. Simulation results were also presented. (NEDO)

Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

On-site verification trials using fly ash for reclamation behind bulkheads; Sekitanbai wo gogan uraumezai ni riyosuru genba jissho chosa

Energy Technology Data Exchange (ETDEWEB)

Kozawa, K [Center for Coal Utilization, Japan, Tokyo (Japan); Yoshida, T [Toyo Construction Co. Ltd., Tokyo (Japan); Miyagawa, H; Kobayashi, M

1996-09-01

As a method to utilize coal ash generated from coal burning power plants more effectively in bulk, its use has been studied as a reclamation material behind bulkhead structures in harbors and airports. Verification trials for the study results were performed at the Hekinan power plant of the Chubu Electric Power Company. The trials included the following: an experiment to verify horizontal soil pressure and active earth pressure when slurry made of fly ash added with cement and seawater was placed in frameworks installed behind bulkheads of a harbor, a slurry hardening test, environmental impact investigation, and constructibility investigation. As a result, a large number of findings were obtained, including the following matters: earth pressure of slurry which has been placed in a soil tank in about ten minutes would be measured as pressure of liquid, but it shifts to behavior as a soil in a relatively short time; the earth pressure after three hours agreed with static earth pressure calculated under provision of K{sub o} = 0.2; and a hardened body made with cement under a certain mixing ratio was obtained, which stands by itself at a height of 7.5 m at compression strength of 1.77 kgf/cm {sup 2}. 11 figs., 2 tabs.

Demonstrative study for the wind and solar hybrid power system. 2; Furyoku taiyoko hybrid hatsuden system ni kansuru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

Kimura, Y; Sakuma, H; Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan)

1996-10-27

In order to verify the complementary relationship between wind and solar energy, the long-term field test of the hybrid power system was conducted at the natural energy square of Ashikaga Institute of Technology. The solar cell blade windmill composed of a Savonius windmill and flexible solar cells applied to swept buckets was also prepared. As a result, the wind power generation was promising mainly in the winter period including the late fall and early spring, while solar one was stable all the year through although it was slightly poor in winter. Stable power generation was thus achieved by combining wind energy with solar energy. As the whole data of other wind and solar power generation systems at the square were analyzed for every month, the same conclusion as the solar cell blade windmill was obtained as follows: the wind power generation in Ashikaga area is promising in Nov.-March from the field test result for 16 months, solar power generation is stable all the year through, the hybrid power system is effective in Nov.-April, and the solar cell blade windmill is equivalent to the hybrid power system. 3 refs., 5 figs.

Comparison about the bone material examination of JIS and ISO; Honezai shiken ni kansuru JIS to ISO no hikaku

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Sumie.; Yanagi, Kei.; Shimura, Akiharu.; Murohoshi, Shiori. [Japan Testing Center for Construction Materials, Tokyo (Japan)

1998-12-01

There are various things in slug bone material and so on manufactured from the macadam, crumble sand. Which crushed rock including gravel, sand to produce in the nature and which was manufactured, and a lightweight bone material and the industry by-product with the bone material used for the concrete. It is necessary with a bone material to grasp the nature of the bone material itself properly to occupy about 70% of the capacity in the concrete and to manufacture the good concrete of the quality from the influence that influence to the various concrete materiality that quality being big. When the quality of a bone material to use for the concrete is confirmed, an examination is being done in accordance with the way of examining it established as the Japanese industry standard in our country. (NEDO)

FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

Stochastic model of flow and dispersion of fine particles in a packed bed; Kakuritsu katei wo mochiita juten sonai deno funtai no ryudo to bunsan model

Energy Technology Data Exchange (ETDEWEB)

Takeda, K [Kawasaki Steel Corp., Tokyo (Japan); Lockwood, F

1996-06-01

For the calculation of pulverized coal combustion in a blast furnace blow pipe and tuyere, a model was built for the evaluation of the movement and dispersion of particles in a packed bed by use of a stochastic approach. In the stochastic particle trajectory calculation taking into consideration the impact of fluctuations in gas turbulence, interaction distance between particles and eddies and interaction time have to be determined, in addition to fluctuations in gas flow velocity (to be determined by measuring the instantaneous flow velocity in a normal distribution generated according to random numbers). The eddy life was determined using Shuen`s formula on the premise that the particle-eddy interaction occurs within the calculated life or the transit time, whichever is shorter. As for the turbulence energy {kappa}, it was determined by the {kappa}-{epsilon} model for the free space and by the {kappa}-Lm(mixing length) model for the packed bed. From the average of a multiplicity of particles in the experiment, such time average specific values as the average density and flow velocity vectors of particles in the space, and particle trajectories, were calculated, which proved to agree with values from experiments. Once in the packed bed, the pulverized coal underwent a sudden deceleration due to its interaction with particles in the packed bed, and the pulverized coal flow near the central axis was rapidly diffused in the packed bed. This model is expected to find its use in the study of pulverized coal combustion in the blast furnace. 18 refs., 12 figs., 2 tabs.

Test and survey on a next generation coal liquefying catalyst. Coal molecule scientific test and survey as the base for commercializing the coal liquefying technology; Jisedai sekitan ekika shokubai shiken chosa. Sekitan ekika gijutsu shogyoka kiban to shite no sekitan bunshi kagaku shiken chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The test and survey on a next generation coal liquefying catalyst present a new proposal to raise catalytic activity in coal liquefaction, and perform demonstration experiments in a laboratory scale to search for possibility of developing a new coal liquefying catalyst from various viewpoints. To explain, discussions were given on the catalyst to perform the followings: liquefaction under extremely mild conditions by using ultra strong acids not limited only to metals; ion exchange method and swell carrying method to raise catalyst dispersion very highly, enhance the catalytic activity, and reduce the amount of catalyst to be used; mechanism of producing catalyst activating species to further enhance the activity of iron catalysts; and pursuit of morphological change in the activating species. The coal molecule scientific test and survey as the base for commercializing the coal liquefying technology performed the studies on the following items: pretreatment of coal that can realize reduction of coal liquefaction cost; configuration of the liquefaction reaction, liquefying catalysts, hydrocarbon gas generating mechanism, status of catalysts after liquefaction reaction, and reduction in gas purification cost by using gas separating membranes. Future possibilities were further searched through frank and constructive opinion exchanges among the committee members. (NEDO)

Final report on the survey to verify a new method for power load leveling; Fuka heijunka shinshuho jissho chosa saishu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of this verification survey is to verify the effectiveness of a system using capacitor for power load leveling and output leveling in the photovoltaic power generation. For the former, the charge is conducted in the nighttime, and the discharge in load peak time in the daytime. The capacity required is small for the output, and therefore, there is a viability of capacitor. For the latter, abrupt output variations by solar cells are leveled by storage device using capacitor. Since the output variation generated in a short time by solar cells requires responsibility and life in case of abrupt charge/discharge, it is suitable to use capacitor. The demonstration use capacitor is an organic stacking type for the former, and an organic jelly-role type for the latter. As a result of the demonstration, for the former, a power storage system which has 32-module series/parallel connection bank switch type + 2-way ac/dc exchanger was made and operated for verification. The overall efficiency of 85% was obtained. For the latter, a system which has 2,400F x 70 series bank, 6,000F x 70 series bank x 3 parallel bank and 3kW solar cells was operated for verification. Much effect of output leveling was confirmed. (NEDO)

How to examine flaking sex evaluation of the float bus bottom brick; Furotobasubotomu renga no furekingu sei hyoka shiken hoho

Energy Technology Data Exchange (ETDEWEB)

Yoneyama, R. [Yotai Refractories Corp., Osaka (Japan)

1999-02-01

After it was used in the float law glass dissolution drawer fireplace bottom, a countermeasure was established by answer, laboratory simulation and high temperature load deformation investigation that that cause was in performance about incumbent elephant of the bottom department clay brick which becomes clear from the second. Though it accompanies melting metal tin and Na that it got into the inside of the brick is a cause as for formation, is expected future development by the high research of the practical use which effective measure was taken against by the organization of the clay brick and the improvement of the physical nature. (translated by NEDO)

Field test on sand compaction pile method with copper slag sand; Dosuisai slag wo mochiita SCP koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Minami, K.; Matsui, H.; Naruse, E.; Kitazume, M. [Port and Harbour Research Inst., Kanagawa (Japan)

1997-09-20

This paper describes the sand compaction pile (SCP) method using copper slag sand. The SCP method is a method by which sand compaction piles are constructed in the ground, and improvement can be obtained in a short period. This method has been widely used even in the port areas for enhancing the bearing power of soft clay ground and the lateral resistance of sheet pile. A great deal of sand is required as a material. The sand requires high permeability, proper size distribution with less fine particle fraction content, easy compaction property with enough strength, and easy discharging property from the casing of construction machines as required properties. Recently, it becomes hard to secure proper sand materials. The copper slag sand is obtained from refining process of copper as a by-product which is quenched in water flow and crushed in water. The copper slag sand has higher particle density than that of sand, excellent permeability, and similar size distribution to that of sand. From compaction drainage triaxial compression test and permeability test, it was found that the mechanical properties of copper slag sand did not change by the crushing of grains with keeping excellent permeability. Through the test construction, applicability of the copper slag sand to the SCP method could be confirmed as an alternate material of sand. 17 refs., 9 figs., 4 tabs.

Test results of cultivation of vegetables with fish breeding water; Yogyosui riyo ni yoru yasai saibai shiken kekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nishida, S. [Hokuriku Electric Power Co. Inc., Toyama (Japan)

1997-10-28

Entrails of fish, fowls and domestic animals are mostly incinerated at large expenses, although partly used as foods. This study is to test `possibility of vegetable cultivation with fish breeding water,` where the entrail wastes are used as baits for fish breeding, and fish excretions are used as the fertilizer for vegetable cultivation to purify water for fish breeding. The cultivation bed consists of two sections, one for fish breeding/vegetable cultivation and the other for vegetable cultivation by the normal method. Vegetable grow notably less in the former than in the latter, 54.6 to 79.5 versus 100. Spinach contains slightly higher contents of vitamins A and C by 6 and 13%, when cultivated in the former than in the latter. Quantities of total nitrogen, phosphorus and potassium as the fertilizer components in the former are 49, 49 and 1.7% of those in the latter. It is predicted, judging from growth of the vegetables, that the former gives a harvest comparable with that by the latter, when given a 6 to 13 days longer cultivation period. 3 figs., 2 tabs.

Investigation of the comparative test method of solar DHW system; Solar kyuto system no toitsuteki seino shiken hoho no chosa

Energy Technology Data Exchange (ETDEWEB)

Oishi, M; Noguchi, T [Japan Quality Assurance Organization, Tokyo (Japan)

1996-10-27

For the development of a unified performance test method for solar DHW (domestic hot water) systems, the Japan Quality Assurance Organization test was applied to three types. In an individual test, each specimen is exposed to irradiation from a solar simulator for 8 hours in a specified pattern. Upon completion of the 8-hour irradiation, hot water is taken from the specimen, the amount being 1.1 times as large as the heat accumulation tank capacity, for the measurement of the collected heat. The control of the heat medium circulation pump, flow rate, and density, all supposed to affect the heat collecting performance, are examined. Stable data, not subject to meteorological factors and high in reproducibility, is obtained, allowing a single test to represent the heat collecting performance. A system test continues for 24 hours, from 8 o`clock on this morning through 8 o`clock on the following morning, with water collected in a specified pattern. This test is suitable for examining the in-service performance of a solar hot water system including the auxiliary heat source. If temperature is not set properly in the auxiliary heat source before testing, the system performance coefficient and sun-dependency coefficient will not be expressed in a uniform manner. For a correct evaluation, measurements should be made only after a several days` uninterrupted operation for the removal of the adverse effect of the heat residual in the heat accumulation tank. 4 refs., 5 figs., 9 tabs.

Report on the fiscal 1997 result of the Japan-China joint demonstration project of environment-friendly cost utilization systems. Low grade coal combustion system (Zhejiang Huba Co. Ltd.); 1997 nendo seika hokokusho kankyo chowagata sekitan riyo system kyodo jissho jigyo. Teihin`itan nensho system ni kakawaru jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This demonstration project aims at reduction of pollutants derived from coal utilization in China by demonstration of CCT to be diffused in China and preparation of diffusion bases, and stable import of energy for Japan. A low-grade coal combustion system burns low-grade coal by use of an internal circulating fluidized bed boiler which burns coal by uniform mixing and circulation of coal and some particles such as limestone and ash. Main specifications of the boiler are as follows: evaporation rate of 35t/h, steam pressure of 3.82MPa (39.0kg/cm{sup 2}), steam temperature of 450degC, water supply temperature of 150degC, internal circulating fluidized bed combustion type, boiler efficiency of 75%, and desulfurization rate of 90% or more. Main properties of low-grade coal are as follows: calorific value of 1830kcal/kg, coal size of 10mm or less, total water content of 2.5%, total S content of 2.7%, ash content of 67.7%, limestone purity of 50% or more, and stone size of 3mm or less. The results in fiscal 1997 are as follows: field survey and arrangement, basic planning and design, design, production and procurement of equipment, training, and dispatch of field supervisor. 26 figs., 3 tabs.

Fiscal 1997 report on the development of new hydrogen atomic energy demonstrative technology; 1997 nendo kenkyu hokokusho (shinsuiso energy jissho gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

In this validation study, phenomena of excess heat which are said to be generated by electrolysis of deuterium using palladium metal, etc. as electrode are taken as `new hydrogen atomic energy,` and to clarify a possibility of using them as a future energy source, the abnormal heating phenomenon was validated and the mechanism was elucidated. The study targeted quantitative control of heat emissions. The study was finished in 1997, the fifth year from the start. The excess heat measurement could partially be reproduced; however, when conducting a confirmation experiment on the excess heat by another more reliable method under the same condition, it was found that the value of excess heat was not an absolute value exceeding measuring sensitivity and errors of the system. If the excess heat of 0.1W order is to be emitted in nuclear reaction, any reactive product should be detected in a substantial quantity. However, the product of a large quantity was not found. A possibility was found out of an increase in nuclear reaction ratio inside solid by low energy deuterium irradiation. From the above, it was concluded that the use of new hydrogen atomic energy was negative. 20 refs., 149 figs., 29 tabs.

Estimation of tire characteristics by concerning test data of vehicles; Jidosha no senkai shiken data ni yoru dire tokusei no suisan

Energy Technology Data Exchange (ETDEWEB)

Nakamura, M; Sekine, T; Nagae, H [Nihon University, Tokyo (Japan)

1997-10-01

To study and/or develop the vehicle motion of a braking in turns theoretically, the cornering characteristics of the tire under the action of braking forces must be required. On the other hand, such data are very few to be published and also there be few tire testing machine to be able to use. The authors tried to derive such data from the vehicle behaviors in steady turns and braking in turns. Because each wheel loads are unknown factors, the two wheeled vehicle model are employed in analysis. The methodology of analysis and the reasonable results are presented in this paper. 5 refs., 10 figs., 2 tabs.

FY 1983 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential supply amount of overseas resource - Survey of methanol usability (Conceptual design of methanol reformed gas turbine); 1983 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru riyo kanosei chosa) - Metanoru kaishitsu gata gastabin no gainen sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

For the purpose of using methanol as power generation use fuel, the paper carried out of the conceptual design of methanol reformed high efficiency gas turbine and the evaluation study of economical efficiency. The methanol reformed gas turbine is to recover the heat from turbine flue gas and to improve thermal efficiency by using the fact that the vapor reforming reaction or decomposition reaction of methanol advance endothermicly at low temperature between 250 and 350 degrees C. It was judged that the combination with the existing technology made the practical application possible and that it was appropriate to adopt the regenerative gas turbine/water-injection and reforming (RGGT/WI and R). As a result of the trial calculation of construction cost of RGGT/WI and R and calculation of power generation cost, RGGT/WI and R became more profitable than the simple open gas turbine at a capacity ratio of 10% or more, and became more profitable than the combined cycle at all capacity ratios. In the use of RGGT/WI and R, which uses methanol as fuel, SOx is not included in flue gas, and the NOx included is estimated at 35ppm or so. The amount satisfies the standard according to the boiler using fluid as fuel. (NEDO)

Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

Research on effective botanical production technology. Method established for the qualitative evaluation of hydroponically cultivated teat; Shokubutsu seisan gijutsu no koritsuka kenkyu. Suiko saibaicha no hinshitsu hyokaho no kakuritsu

Energy Technology Data Exchange (ETDEWEB)

Ota, T; Harada, K [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1995-06-14

In case of cultivation on the ground, the tea is produced about five years after the transplantation. In case of hydroponic cultivation, however, it can start in about two years. Against difficulties due to the high temperature in summer, the cool summer climate of Hokkaido is good for putting the hydroponic cultivation to practical use. As the tea is a nonessential grocery item, its quality is regarded as very important, and determined by its theanine and other free amino acid content. Therefore, a new measurement method by high-speed liquid chromatography was studied to establish the method of quantitatively analyzing the free amino acid. By applying this method established, the hydroponically cultivated tea was qualitatively evaluated through classifying it and measuring its free amino acid content at each of its foliage heights. The main free amino acid contained was known to be theanine, glutamine, arginine, threonine and alamine. The theanine accounted for about 70% of all the free amino acid, and with a decrease in foliage height, its content fell. 15 refs., 20 figs., 2 tabs.

Consideration on standard substance for the conbustion test of oxidizing solid. Sankasei kotai no nensho shiken no kijun busshitsu ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Muranaga, K [The Japan Carlit Co. Ltd., Tokyo (Japan); Tamura, M; Yoshida, T [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1991-04-15

The mixture of KClO {sub 3} and wood flour is the standard substance in the combustion test by the Fire Service Law to investigate the accelerating combustion of an oxidizing agent, but it is difficult to measure the combustion time owing to the intermittent combustion. This paper described the study to get any compounds superior to the above mentioned. Since the mixture of KNO {sub 3}-wood flour combusts more rapidly than that of KClO {sub 3}-wood flour, a new mixture of similar combustion rate to that of the mixture of KClO {sub 3} and wood flour and without intermittent combustion was tried to get by adding an inactive solid powder to decrease the combustion rate. But a new mixture which has the combustion time of about 4 minutes, shows uniform combustion instead of intermittent combustion and shows the only slight variation of combustion time, could not be found. It is because of intermittent combustion that the mixture of KClO {sub 3} and wood flour can endure the combustion for 4 minutes although this mixture has larger reaction heat. The combustion time of this mixture is shortened if the igniting nichrome wire temperature exceeds 1,000 centigrade. Further, the bulk density of deposit affects greatly the combustion time. 7 refs., 2 figs., 4 tabs.

Application of streaming potential method for detection of fractures in granitic rock; Kamaishi kozan ni okeru ryutai ryudo den`iho tekiyo shiken

Energy Technology Data Exchange (ETDEWEB)

Negi, T; Yokoi, K; Yoneda, Y [Nittetsu Mining Co. Ltd., Tokyo (Japan); Senba, T [Power Reactor and Nuclear fuel Development Corporation, Tokyo (Japan)

1996-05-01

Measurements were made using the streaming potential method for the purpose of investigating the expansion of hydration cracks, direction of their propagation, and the chaining of cracked surfaces, in the granitic rock. Tests were conducted by use of a bore hole in the gallery wall. The bore hole yielded approximately 400 liters of water per minute, the bore hole was closed and then opened, and the change with the passage of time in the spontaneous potential (SP) on the gallery wall was measured. At a spot 31.2m from the mine entrance, the SP dropped by 15mV simultaneously with the opening of the bore hole, and rose by 14mV simultaneously with the closure of the same. The phenomenon was true for other locations, that is, for the section from the mine entrance to a spot 9.0m therefrom, and for a section beginning at 15.0m and ending at 19.2m therefrom. No change in the SP was observed in a group of cracks with water springing out of the gallery roof, beginning at a point 40m and ending at a point 54m from the mine entrance. The result suggests the possible application of the streaming potential method to the investigation of cracks. 1 ref., 10 figs.

Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 1/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 1/3)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test of the motor-operated valve, individual test of the gasification furnace circulation water pump, individual test of the motor for the same, individual test of the SGC (syngas cooler) circulation water pump, individual test of the coal feeder rotary valve, individual test of the foreign matters extraction rotary valve, individual test of the foreign matters classifier, individual test of the char feeder rotary valve, individual test of the slag conveyer, individual test of the slag vibrator, individual test of the slag crusher, individual test of the slag separation tank exhaust blower, individual test of the slag separator water pump, test of gasification furnace interlocking, verification test of alert for the same, test of gasification furnace system pressure rise, test of oxygen line ventilation, test of comprehensive purge master sequence, verification test of distribution performance of the distributor, test on char system rock hopper pressure application and pressure release, test of pneumatic actuator valve loop, actual operational test of the soot blower, and an individual test of the receiving conveyer. (NEDO)

Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 3/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 3/3)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include a test operation of the expansion turbine in the air separation facility, test operation of the lubricating oil pump for the expansion turbine in the same, test operation of the oxygen compressor in the same, test operation of the medium pressure nitrogen compressor in the same, test operation of the lubricating oil pump for the medium pressure nitrogen compressor in the same, test operation of the high pressure nitrogen compressor in the same, performance verification test for the air separation facility, sequence test for upper/lower stage normal pressure coal hopper purge master in the gasification facility, sequence test for upper/lower stage initial coal loading master in the same, sequence test for char system rock hopper pressure application master in the same, sequence test for gasification furnace light oil leak check master in the same, sequence test for coal rock hopper pressure application master in the same, sequence test for upper/lower coal rock hopper coal reception master in the same, sequence test for slag hopper quenching operation master in the same, and sequence test for gasification steam drum water filling master in the same. (NEDO)

Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Test result report - 2/3); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Shiken kekka hokokusho 2/3)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the development of a coal gasification furnace optimum for fuel cells, a pilot test facility was constructed, and the results of tests and inspections conducted therefor are put together. They include an individual test of the receiving pit hopper vibrator, individual test of the pulverized coal related rotary valve, individual test of the pretreatment compressed air fan, individual test of the coal pulverizer lubricating device, individual test of the coal pulverizer pressure device, individual test of the coal pulverizer, individual test of the coal pulverizer motor, individual test of the coal feeder, individual test of the pulverized coal bunker exhaust fan, individual test of the pulverized coal bunker exhaust fan motor, test of capacity for pulverized coal, individual test of the pulverized coal conveyer blower, test of the sequence of the same, test of pulverizer inert clearing, individual test of the pretreatment condensed water pump in the coal pretreatment device, test of airborne conveyance in the same, verification test of inter-hopper transfer in the same, test of coal pulverization in the same, test operation of the raw material air/low pressure nitrogen compressor in the air separation facility, test operation of the raw material air freezer in the same, and a test operation of the MS adsorber/MS regeneration electric heater. (NEDO)

Test work of sand compaction pile method on coal ash soil foundation. Sekitanbai jiban ni okeru sand compaction pile koho no shiken seko

Energy Technology Data Exchange (ETDEWEB)

Goto, K.; Maeda, S.; Shibata, T. (The Kansai Electric Power Co. Inc., Osaka (Japan))

1992-01-25

As an electric power supply source after the 1990 {prime}s, Nos. 5 and 6 units are additionally being constructed by Kansai Electric Power in its Himeji Power Station No.1 which is an exclusively LNG burning power station. The additional construction site of those units is of soil foundation reclaimed with coal ash which was used residual product in the existing No.1 through No.4 units. As a result of soil foundation survey, the coal ash layer and sand layer were known to be of material to be possibly liquidized at the time of earthquake. As measures against the liquidization, application was basically made of a sand compaction pile (SCP) method which is economical and abundant in record. However, that method was so short of record in the coal ash layer that its evaluation was difficult in soil reforming effect. Therefore, its applicability was evaluated by a work test on the site, which resulted in a confirmation that the coal ash as well as the sand can be sufficiently reformed by the SCP method. Started in September, 1991, the additional construction of Nos. 5 and 6 units in Himeji Power Station No.1 uses a 1.5m pitch SCP method to reform the soil foundation. 3 refs., 10 figs., 1 tab.

Lateral loading test of full-scaled pile foundation focused on ultimate behavior; Shukyoku kyodo ni chakumokushita jitsubutsudai kui kiso no suihei saika shiken

Energy Technology Data Exchange (ETDEWEB)

Kosa, K. [Hanshin Expressway Public Corp., Osaka (Japan); Suzuki, N. [CTI Engineering Co. Ltd., Tokyo (Japan); Kimura, M. [Kyoto University, Kyoto (Japan); Kimura, Y. [Public Works Research Institute, Tsukuba (Japan); Morita, Y. [Kiso-Jiban Consultants Co. Ltd., Tokyo (Japan)

1998-06-21

Lateral loading test of full-scaled pile foundation was made up to the ultimate limit state to establish a limit state design method for pile foundations. A full-scaled 3-by-3 pile group driven as bridge foundation was used for the test. A surface reclaimed layer is nearly 13cm in thickness. The lateral unidirectional loading test was repeatedly carried out by using 6 hydraulic jacks at 30MN in maximum load capacity and 50cm in maximum allowable deformation. The test and analysis results are as follows. In a range of 0-40% in pile head displacement/pile diameter ratio, a load-carrying capacity increased gradually. The yield point of a load-displacement curve agreed with the point at which a reinforcing bar of a pile body reaches analytical yield stress. Bending moment of a pile body and shear stress of a pile head increased in the order of back, middle and front rows. It was confirmed that a framework analysis method considering the non-linearity of a pile body and bedrock is also applicable to full-scaled pile group foundations. 17 refs., 32 figs., 3 tabs.

Achievement report on developing superconductor power applied technologies in fiscal 1999 (2). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power generators. This paper summarizes the achievements thereof in fiscal 1999. A verification test was given on the rotor of an ultra high speed responding generator. In a sudden short circuit test using the different phase charging method, no anomalies were found such as quench generation and vibration changes, wherein the healthiness of the generator was verified. In the VVVF actuation test, knowledge was acquired on the actuation method when the ultra high speed responding generator is applied to a combined cycle plant. After the verification test has been completed, the disassembly inspections such as visual check and non-destructive test were performed. With regard to the vacuum leakage found in the rotor under very low temperatures, the causes were presumed and the countermeasures were discussed by observing the weld structures. In the design research, the conception design on the 200-MW pilot generator was reviewed by reflecting the results of the verification tests on the model generator. At the same time, trial design was made on a 600-MW target generator. In summarizing the overall research achievements, the achievements and evaluations were summarized on technological issues that have been allotted to each research member. (NEDO)

Achievement report for fiscal 1998 on the development of superconductor power application technology. 2. Research and development of superconducting wire and superconductive power generator, research of total system, research and development of refrigeration system, and verification test; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total sytsem no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The slow excitation response type power generator is studied when the rotor and stator of a 70,000kW-class model are combinedly subjected to an on-site verification test, when a good result is obtained. The rotor is disassembled for inspection, and its members are found to be sound without any problem in terms of mechanical strength. The quick excitation response type is studied when a 70,000kW model is experimentally built and subjected to an on-site verification test after a rotation and excitation test in the factory, when the pilot machine concept design is reviewed. In the study of a total system, efforts continue for the review of the model machine test method, improvement on generator design and analytical methods, development of operating methods, and the effect of its introduction into the power system. Since a He-refrigerated system is requested to exhibit high reliability for application to power equipment and to be capable of continuous long-period operation, a system having constituents with their reliability enhanced and an appropriate redundant system is developed, and a verification study is under way which will continue for more than 10,000 hours. Described also is an oil-free low-temperature turbo refrigerator. The latest quick excitation response type rotor is also tested for verification. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report refers, continuously to the Part 1, to the in-situ verification test of the slow-response type model machine rotor and to the review of the conceptual design of the pilot machine. On the basis of the R and D results of various element technology/partial models obtained before the previous fiscal year, the design, manufacturing and factory test had been conducted for a 70,000kW class slow-response type model machine rotor. This year, an in-situ verification test was performed to complete the test of all planned test items. Using the technological results obtained in the design, manufacturing and test of the 70,000kW class model machine, the conceptual design is being reviewed of the 200,000kW class pilot machine. In the aspect of the functional design, accurate grasping of the thermal load is essential for the purpose of attaining a large capacity for a superconducting generator, as a part of which a thermal load analytical method was planned to be established for a torque tube heat exchanger. The reasonableness of the analysis was verified through a comparison with the factory test result of the 70,000kW class slow-response type rotor, indicating good agreement between the calculation result and the actual measurement, and enabling the result to be obtained that explains dependency of the thermal load on the number of revolution. (NEDO)

Achievement report on developing superconductor power applied technologies in fiscal 1999 (1). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power applied technologies. This paper summarizes the achievements thereof in fiscal 1999. In research and development of the superconductor wire materials, decrease in loss and increase in capacity of the conductors were progressed for the Nb{sub 3}Sn wire material, whereas its mechanical properties and stability were evaluated. In research and development of the superconductor generators, an ultra high speed responding generator was verified of its healthiness in a sudden short circuit test. A linkage test with an operating 77-kV system was performed, wherein verification was given that the superconductor generator can be operated stably against various disturbances. In research and development of the freezing systems, an improved system was structured, which achieved operation of 11,390 hours in a single system as a result of the high reliability of the oil-free structure. In the verification tests, the ultra high speed responding model generator was connect to the freezing system to give such tests as load test, onerous test, actuation test by using the M-G system, and 77-kV system linkage test. The functions, reliability, and durability of the system were verified, and different data were acquired. (NEDO)

Fiscal 2001 achievement report. Development of coal gas production technology for fuel cells - Research using pilot test facility - for public release (Part 1 - Construction and test operation); 2001 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu (Sono 1 - Koji shiken unten hen)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2001 results are put together. In the construction of the pilot test facility, work involved the road in the site, road illumination system installation in the site, and an unauthorized entry prevention system. In the construction of the coal gasification facility, work involved electrical instrumentation and painting for the coal feeding system, coal gasification furnace, heat recovery boiler, and so forth, and the installation of a series of devices was completed. In July following the completion, power was received and test operations were started, which included the operation of the coal gasification facility alone. Renting was started in August for the coal pretreatment facility, air separation facility, and the slag treatment device. In the study of the operation control technology for the oxygen-blown coal gasification furnace system, test operations were conducted based on the operating procedures prepared in the preceding fiscal year, which included a test operation performed for the pilot test facility alone. Parameters for equipment control obtained through the test operations, and improvements on operating steps carried out as required, were all reflected on the operating procedures. (NEDO)

FY 1998 report on achievements of the verification survey on a new method for load leveling; Fuka heijunka shinshuho jissho chosa 1998 nendo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An electrically double-layered capacitor is drawing attention as a new power storage technology that can contribute to power load leveling. The issue is to make the capacitor more compact by enhancing energy density. Discussions to improve the energy density are being given on a method by which internal resistance combined with that in electronic circuits may be allowed to some extent. In addition, in order to verify feasibility of its practical use, investigations are made on the optimal operation pattern of the system, possible quantity of introduction, effect of the introduction, and future possibility to reduce the cost. As demonstration of the element technology used in capacitor modules, fiscal 1997 fabricated 35 single cells each with a volume of one liter, and investigated the positioning at practical application, case studies, and operation patterns. Based on the achievements in fiscal 1997, fiscal 1998 performed fabrication and performance test on a capacitor module in which multiple number of cells are connected, and trial fabrication of a next generation type high-energy density capacitor. In addition, as a study on a total system, discussions were given on design and cost estimation of a hybrid type capacitor which combines the capacitor with a NAS battery. (NEDO)

Fiscal 1997 report on the results of the verification survey of a new load leveling method; Fuka heijunka shinshuho jissho chosa (1997 nendo seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A study was conducted of a practical applicability of the electric double layer capacitor as a new electric power storage technique. In the study, a comparison was made between the capacitor system and the NAS battery which is most commercialized as one for power storage of all the secondary batteries. The capacitor system is excellent in cycle life, system efficiency, and safety/environment, but in energy density it is approximately a tenth of that of the NAS battery so far. The capacitor system, however, is high in filling rate in modules and enables compact design. As to the 35 fabricated electric double layer capacitor cells, the following tests were carried out: charge and discharge, internal resistance measurement, energy density measurement, characteristics of charge/discharge efficiency, self-discharge characteristics, and characteristics of circumferential temperature. As a result of the tests, the cell with volume energy density of 16.4-16.8 Wh/L was fixed to the module with a filling rate of about 93% and achieved an energy density of 15 Wh/L. 26 refs., 175 figs., 75 tabs.

Probabilistic evaluation method for axial capacity of single pile based on pile test information. Saika shiken kekka wo koryoshita kuienchoku shijiryoku no kakuritsuronteki hyokaho

Energy Technology Data Exchange (ETDEWEB)

Ishii, K.; Suzuki, M. (Shimizu Construction Co. Ltd., Tokyo (Japan)); Nakatani, S. (Ministry of Construction Tokyo (Japan)); Matsui, K. (CTI Engineering Co. Ltd., Tokyo (Japan))

1991-12-20

To consider the safety and economics in the design of pile, the reasonable evaluation on estimated accuracy from the accuracy of equation of pile capacity and probabilistic evaluation method is necessary. Therefore, the data analysis based on the collection and summary of the results from load tests of piles is one of powerful approach. In this study, selection of the parameters that cannot obtained from probabilistic model and load test and combination between statistical and experimental data by using Baysian probabilistic theory was examined. As the feature of this study, use of the design pile capacity equation based on the model of evaluation of pile capacity, consideration of the intrinsic difference between statistical data and results of load tests by using Baysian probabilistic theory and quantitative examination of applicability of the proposed method and the results of load tests are given. 24 refs., 5 figs., 7 tabs.

Resistance test of high-speed ship by means of attitude control method. Part 2; Shisei seigyo hoshiki ni yoru kosokutei no teiko shiken. 2

Energy Technology Data Exchange (ETDEWEB)

Hayashida, S [Nagasaki Institute of Applied Science, Nagasaki (Japan)

1996-04-10

The previous paper has proposed a resistance test method by controlling the attitude of a high-speed model ship using a personal computer without making a data base. For this method, the fluid force acting on the hull of model ship is measured, to change its attitude based on the measurement, and then, the fluid force is measured again, to change the attitude again. The traveling attitude is created by repeating this, to measure the force acting on the hull. Since the attitude is changed by calculating using the fluid force measured, various factors can be considered in the calculation process. For example, a test with an arbitrary displacement in an arbitrary position of center of gravity can be conducted in spite of actual displacement and position of center of gravity of the model ship. A test for a high-speed ship was conducted through this method, to obtain nearly satisfactory results compared with a usual resistance test. Occasionally, a lot of repetitions were required to satisfy the balancing condition of the force. In this study, the improvement of testing efficiency has been planned by modifying the analyzing program. 5 refs., 7 figs., 1 tab.

Wind tunnel investigation of a USB-STOL transport semi-span model. 2; CAD sekkei ni yoru USB-STOL ki hansai mokei no fudo shiken. 2

Energy Technology Data Exchange (ETDEWEB)

Takahashi, H; Okuyama, M; Fujieda, H; Fujita, T; Iwasaki, A [National Aerospace Laboratory, Tokyo (Japan)

1994-11-01

The Quiet Short Take-Off and Landing (QSTOL) Experimental Aircraft `ASKA` has been researched and developed by the National Aerospace Laboratory (NAL). The `ASKA` was based upon the airframe of the home produced C-1 tactical transport which was modified into the Upper Surface Blowing (USB) -powered high- lift STOL aircraft. The wing configuration, however, was not changed. Therefore, this Experimental Aircraft does not always have the optimum configuration of a USB-type aircraft. So the authors tried to improve the aerodynamic characteristics of the STOL Aircraft. This paper describes the investigations which have been conducted to improve the aerodynamic characteristics of a subsonic jet transport semi-span model with an Upper Surface Blown Flap system which has been newly designed using the NAL STOL-CAD program. The model had an 8.2{degree} swept wing of aspect ratio 10.0 and four turbofan engines with short USB nozzles. The tests were conducted in the NAL 2{times}2m Gust Wind Tunnel with closed section and results were obtained for several flap and slat deflections at jet momentum coefficients from 0 to 1.85. Compared with the aerodynamic characteristics of the `ASKA` model, we determined that the airframe weight can be reduced and the aerodynamic characteristics can be improved significantly. 14 refs., 44 figs.

Application of streaming potential method for detection of fractures in granitic rock. part 2; Kamaishi kozan ni okeru ryutai ryudo den`iho tekiyo shiken. 2

Energy Technology Data Exchange (ETDEWEB)

Negi, T; Yoneda, Y [Nittetsu Mining Co. Ltd., Tokyo (Japan); Senba, T [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

1997-10-22

Streaming potential method has been applied in the Kamaishi Mine. In FY 1995, self-potential (SP) was monitored on the wall of gallery by varying the pressure in the well with open/close operation of the mouth of well having spring water, which was drilled from the gallery. It was confirmed that SP changes remarkably at the wall having a great number of fractures with spring water. It was considered that the change in SP is due to the streaming potential generated by the flowing underground water from the gallery side to the fractures in the well. In this paper, this continuity of the wall of gallery and the fractures in the well is estimated. In the present tests, SP changes were observed at walls of surrounding galleries by varying the pressure in the well with open/close operation of the mouth of borehole at various drilling depths during drilling of borehole. As a result, SP changes were observed at the wall of gallery when reaching to the depth with increased spring water. The results agreed well with the test results conducted at the same field in FY 1995. It was confirmed that the streaming potential method is a useful method for grasping the hydraulic continuity in the rocks. 2 refs., 9 figs.

Current limiting experiment with 600 V/100A rectification type superconducting fault current limiter; 600 V-100A kyu seiryugata chodendo genryuki no genryu shiken

Energy Technology Data Exchange (ETDEWEB)

Matsuzaki, J.; Tsurunaga, K.; Urata, M. [Toshiba Corp., Tokyo (Japan); Okuma, T.; Sato, Y.; Iwata, Y. [Tokyo Electric Power Co., Inc., Tokyo (Japan)

1999-06-07

The rectification type current limiter with the current-limiting system of the new type which combined rectifier circuits with the direct current reactor has been proposed until now, and it has succeeded in the current-limiting test by the normal conduction reactor by the 6.6kV class model vessel. Since the loss of the conductor becomes fundamentally the zero, in the same current limiter, by using superconducting wire rod, because direct current always flows in the reactor, making into low-loss becomes possible. In this report, this paper describes cut-off characteristic of 600V/100A rectification type superconductive current limiter using the metal type superconductive conductor. (NEDO)

Results of the DIOS pilot plant test and summary of the joint research; DIOS pilot plant no shiken sogyo kekka to kenkyu seika no matome

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawaoka, K [The Japan Iron and Steel Federation, Tokyo (Japan)

1996-09-01

A joint research had been carried out with a subsidy from the Agency of Natural Resources and Energy since fiscal 1988 to fiscal 1995 on the direct iron ore smelting reduction process (DIOS process). The process utilizes coal directly as a process to use the strong points and supplement the weak points of the blast furnace process. During the period, a pilot plant had been operated since 1993. Upon having completed the feasibility study, this paper reports the result thereof. The main facilities consist of a smelting and reducing furnace of iron bath type, a spare reducing furnace of fluidized bed type, and a preheating furnace. The former two furnaces constitute a unit structure with the two furnaces connected vertically. The pilot plant achieved a three-day continuous operation producing 500 tons of iron every day. The production rate reached 21 tons an hour at an upward oxygen blowing velocity of about 13,000 Nm {sup 3} per hour. The coal unit requirement showed a result of <1000 kg/t for high VM coal and <900 kg/t for low VM coal. These results verified a possibility that this process can supplement or replace the blast furnace process even for a production scale of 9000 tons a day. 7 refs., 15 figs., 3 tabs.

Report on results for fiscal 1996 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In fiscal 1996, the initial cooling test and rotary excitation test were conducted for the 70,000kW slow-response type model machine, with the basic characteristics of the rotor verified such as the cooling characteristics, shaft vibration characteristics, mechanical strength, and superconductivity stability, and with the results of the studies explained. The rotor of the 70,000kW slow-response type model was installed in the test site, and the field test was carried out in 1997. For this purpose, research test was performed by the element technology of the model machine and the partial model. The technological development items, trial manufacture and test items were field winding, multi cylindrical rotor and damper. Upon the test results using the element and partial model, the design and manufacturing were implemented of the superconducting generator of a slow-response type excitation method with the output of 70,000kW class. Performed were the basic characteristic test, long-term operation test and severity test on the assumption of abnormality, verifying the characteristics and reliability of the generator as well as obtaining data concerning an excessive electromagnetic force and heat generation. From the test data and the analysis/evaluation results obtained on the model machine, the 200,000kW class pilot machine was reviewed in the conceptual design. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 1. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report explains the outline as Part 1. In fiscal 1997, the 10th year of the project, a multi cylindrical rotary model for which an in-situ verification test was finished was brought back to the plant and dismantled for examination, while the in-situ verification test of a slow-response type model machine rotor was conducted in combination with a refrigeration system. In addition, in the research of AC wire materials and oxide based materials, studies were made with a purpose of high characterization and long wire materialization. In the metallic materials, a 10kANbTi conductor was developed while, in oxide-based materials, research was done on performance improvement and wire materialization based on various synthesizing methods. The manufacturing, factory test and in-situ text were conducted for a 70,000kW model machine with the purpose of R and D of a 200,000kW class pilot machine. Examination was made on the test method of the 70,000kW class model machine, operation technology of a superconducting generation system, and the effect of introducing the superconducting generator into a power system. In the conventional refrigeration system, a single unit test was carried out for the liquefaction, liquid storing capacity, etc., of the system. The 70,000kW class model machine was put through a test for confirming the general operation including the refrigeration system. (NEDO)

Knowledge capital, productivity and competitiveness. Empirical evidence for the G-5 countries; Chishiki shihon no chikuseki to seisansei kokusai kyosoryoku. G5 shokoku ni kansuru jissho bunseki

Energy Technology Data Exchange (ETDEWEB)

Sakurai, N.; Miyazaki, H.

1999-06-01

Technological change is a major driving force for long-run economic growth. New theories on growth have stressed the importance of innovative and adaptive capacity of firms in order to fully reap the benefits of research and development (R and D) within the firms as well as those spilled-over from other firms and abroad. This report empirically investigates the relationship between R&D and productivity as well as that between productivity and industrial competitiveness for the G-5 countries (Japan, the US, (West) Germany, France and the UK). To do so, we have constructed comparable data on R and D capital stock (so-called 'knowledge capital'), the level and growth rates of total factor productivity (TFP), and the revealed comparative advantage (RCA) index for 22 manufacturing industries in each G-5 country. The major results are summarized as follows. First, the volume of knowledge capital for Japan is still far smaller than that of the US (40% for total manufacturing in 1995). Second, there is no clear tendency of TFP convergence to the US level for each country after 1980 and its level for Japan is about 70% of the US in 1993. In addition, the TFP gap between Japan and the US has recently widened for high-tech sector. Third, the estimated elasticities of TFP with respect to the R&D stock for manufacturing sector during the mid-1970s and the early 1990s are 0.07 for Japan and 0.21 for the US on average, with deteriorating R and D potency in Japanese manufacturing. For high-technology industries, they are much larger with the estimates of 0.45 for Japan and 0.86 for the US on average, whereas for Japan the R&D performance becomes worse during the last decade. Fourth, we found that international competitiveness in industries depends not only on TFP and exchange rate fluctuations, but also on various non-price factors such as product quality, marketing ability, and product market segmentation. (author)

Flow characteristic of Hijiori HDR reservoir from circulation test in 1991; Koon tantai Hijiori jikkenjo ni okeru senbu choryuso shiken (1991 nendo) kekka to ryudo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Shiga, T; Hyodo, M; Shinohara, N; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

1996-05-01

This paper reports one example of flow analyses on a circulation test carried out in fiscal 1991 at the Hijiori hot dry rock experimental field (Yamagata Prefecture). A fluid circulation model was proposed to simulate an HDR circulation system for a shallow reservoir (at a depth of about 1800 m) demonstrated in the circulation test by using an electric circuit network (which expresses continuity impedance in resistance and fluid storage in capacitance). Storage capacity of the reservoir was estimated by deriving time constant of the system from data of time-based change in reservoir pressure associated with transition phenomena during the circulation test. The storage capacity was estimated separately by dividing change of storage in the reservoir by change in the reservoir pressure. To derive the storage in the reservoir, a method to calculate non-recovered flows in the circulation test was utilized. The results of evaluating the reservoir capacity in the shallow reservoir using the above two independent methods were found substantially consistent. 3 refs., 6 figs., 1 tab.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - international joint demonstration and development of photovoltaic power generation systems (Demonstrative research on photovoltaic power and micro hydraulic power hybrid system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system kokusai kyodo jissho kaihatsu (taiyoko micro suiryoku hybrid system jissho kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A photovoltaic (PV) power plant is compounded with a micro hydroelectric (MH) power plant in Vietnam, who has a dry season and a rainy season, to structure a stabilized power supply system to compensate drawbacks of the respective systems. Full load operation is being performed to advance the development of technologies to optimize and improve the performance and reliability of the system. The works include (1) site surveys, and decision on a location to execute the demonstration research, (2) design of the system, and design and fabrication of devices, and (3) the building construction thereof. In Item (1), the location was decided at Trang Village, Vietnam from such installing conditions as annual average insolation, water channels for wheel turbines, energy complementing relations, load demand amount, and difficulty of installation. In Item (2), the system consists of PV:100 kW/MH:25 kW/control system, wherein the MH is an inductive generator. The Main devices include generators, batteries, inverters, system control panels, and a meteorological data recording device. In Item (3) land survey and development were completed. (NEDO)

Fiscal 1974-1975 Sunshine Project research report. Hydrogen energy research results (National laboratories and institutes); 1974, 1975 nendo suiso energy kenkyu seika hokokushu. Kokuritsu shiken kenkyusho kankei

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-10-01

This report summarizes the 21 research results on hydrogen energy promoted by 3 national laboratories and 2 national institutes. (1) Tokyo National Industrial Research Institute (TNIRI): Ca-I system, Mn system, S system and hybrid cycles, and water decomposition reaction by CO as thermochemical hydrogen production technique. (2) Osaka National Industrial Research Institute (ONIRI): Fe system, Cu system and ammonia system cycles, and high-temperature high-pressure water electrolysis. (3) Electrotechnical Laboratory: high- temperature direct thermolysis hydrogen production technique. (4) TNIRI: Mg-base and transition metal-base hydrogen solidification technique. (5) ONIRI: Ti-base and rare metal- base hydrogen solidification technique. (6) Mechanical Engineering Laboratory: hydrogen-fuel engines. (7) Electrotechnical Laboratory and ONIRI: fuel cell. (8) TNIRI: disaster preventive technology for gaseous and liquid hydrogen. (9) Chugoku National Industrial Research Institute: preventing materials from embrittlement due to hydrogen. (10) Electrotechnical Laboratory: hydrogen energy system. (NEDO)

Study on application of radar technique to explore mineral resources. 1. Sample test in laboratory; Radar ho no kosho tansa eno tekiyosei kento. 1. Shitsunai shiryo shiken

Energy Technology Data Exchange (ETDEWEB)

Chiba, A; Okada, K [Sumitomo Metal Mining Co. Ltd., Tokyo (Japan); Arai, E [Metal Mining Agency of Japan, Tokyo (Japan); Noguchi, K; Fujiwara, K [Waseda University, Tokyo (Japan)

1997-10-22

Dielectric constants of ore body and mother rock specimens taken from an epithermal gold deposit were measured in the frequency band of radar technique. Applicability of the radar technique to mineral exploration has been investigated by comparing measured results and ore showing. This paper describes the results. Measured results of the dielectric constants are summarized as follows. The specific dielectric constant in the forced dry condition did not depend on specimens. The specific dielectric constant in the water saturated condition increased with increasing the porosity. The conductivity increased with increasing the specific dielectric constant. The specific dielectric constant and conductivity increased with increasing the water content. The specific dielectric constant did not depend on types of rocks. The specific dielectric constant decreased with increasing the frequency. Difference of the specific dielectric constant in the water saturated condition decreased with increasing the frequency. The radar technique was applied to blind deposits. Since they were often in the ground water saturated zones, it was considered that the reflection at the boundary was enhanced with increasing the difference of specific dielectric constant between ore body and mother rock compared with that in unsaturated zones. 8 refs., 8 figs., 3 tabs.

Annual view (1999) - aeronautic relation/space relation. Space relation - communication/broadcasting/engineering test satellite; Nenkan tenbo (1999) koku kankei uchu kankei. Tsushin, hoso, gijutsu shiken eisei kanren

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-05

To cope with the increasing communication demand, the R and D of engineering test satellite V III are being conducted being aimed at developing a technology of the world's largest class geostationary satellite. As to the large developing rectenna, a model for development was manufactured and is now in test. In August and September 1999, the system combustion test of complete two-liquid chemical propulsion system was carried out at Ishikawajima-Harima Heavy Industries. The R and D of the data relay technology satellite are being conducted for the purpose of conducting orbital demonstrative tests to improve the data relay functional performance of satellite and to spread the data relay range. The engineering test satellite VII was developed to study the space rendezvous/docking technology and the basic technology of space use robot. It was launched in November 1997 and got a lot of valuable data. The operation of satellite has been continued for the acquisition of data such as secular changes of satellite equipment. About the communication broadcasting satellite, experiments and functional tests were finished, and the operation was stopped in August 1999. (NEDO)

Development of multi-frequency array induction logging (MAIL) tool. 3; Multi shuhasu array gata induction kenso tool (MAIL) no kaihatsu (genchi shiken data no ichijigen kaiseki). 3

Energy Technology Data Exchange (ETDEWEB)

Sato, T; Osato, K; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan); Uchida, T [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

1996-05-01

A field test was carried out in 1995 on a deep-seated geothermal investigation and reduction well WDR (in Kakkonda, Shizuku-ishi, Iwate Prefecture) by utilizing a multi-frequency array induction logging tool which is under development by NEDO. This paper reports results of analyzing the acquired data. With the WDR wells, an investigation has been conducted to a drilling depth of 330 m. Three frequencies in a range from 3 to 24 kHz provided relatively good data, but data with 42 kHz had poor quality that cannot be utilized for the analysis. Precise device calibration is difficult on data acquired from three array type vertical component magnetometers (the difficulty may be due to a signal line from a transmitter passing on the magnetometer side). Because of this difficulty, analysis using one-dimensional inversion program was performed by using ratio of the amplitude for each frequency and phase difference as input data. The analysis allowed to have derived a result that corresponds to the ground bed structure. 5 refs., 8 figs., 3 tabs.

Exciting test of a floating type cable stayed bridge and its response observation under the typhoon; Furotiingu keishiki shachokyo (Utagenkabashi) no kishinki shiken to taifuji oto kansoku

Energy Technology Data Exchange (ETDEWEB)

Uno, K. [Kyushu Kyoritsu Univ., Kitakyushu (Japan). Faculty of Engineering; Aso, T. [Yamaguchi Univ., Ube (Japan). Faculty of Engineering; Kitagawa, S. [Kyushu International Univ., Kitakyushu (Japan). Faculty of Economy; Kabashima, S.

1995-09-20

Recently, in case of the planning and designing of bridges, of course its practicality and execution stability are considered, but consideration for landscape also is a large problem. In particular, the selection of the bridge type is very important in order to protect the beautiful natural landscape. The cable stayed bridge has become to be executed often, owing to its elegant style, however, it becomes important theme clarify the antiseismic and wind stability because of its complicated structure system and very slender girder. In this paper, the results of the dynamic characteristics of a floating type cable stayed bridge (length 292.1 m and width 14.9 m) and the observation of its dynamic behavior under the typhoon are reported. Microtremor measurement was performed to determine the dynamic characteristics of the bridge under construction. After the construction of the bridge, the excitation test was carried out in order to confirm its natural frequencies, vibration modes and damping constants. From the results of the observation of the dynamic behavior of the girder and cables under the typhoon, the wind stability of this bridge was confirmed. 10 refs., 13 figs., 9 tabs.

Research report of FY 1996 on development of new hydrogen energy demonstration technology. 1. FY 1996 results; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo jisshibun)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat regeneration tests have been successively conducted using two kinds of electrolytic cells. As a result, the excess heat generation measured by one electrolytic cell in FY 1996 has been confirmed in about 35% of repeatability under the same condition. On the other hand, the excess heat over the measuring accuracy was not measured using two kinds of absolute heating value measuring systems. The electrolytic cell, by which the excess heat was measured, was used for confirming the absolute heating value as keeping its condition. When tests were conducted using the developed system, it was found that the absolute heating value can not be detected. Then, verification tests are currently conducted for determining the cause. Moreover, in order to clarify the basic characteristics of materials required for the regeneration of the excess heat generation phenomenon, observation and analysis of the materials were performed before and after the excess heat measurement. Thus, the cause of difference was revealed. 3 refs., 98 figs., 24 tabs.

Flow characteristics of Hijiori HDR reservoir form circulation test in 1995; Koon tantai Hijiori jikkenjo ni okeru shinbu choryuso yobi junkan shiken (1995 nendo) kekka to ryudo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Fukushima, N; Hyodo, M; Shinohara, N; Takasugi, S [Geothermal Energy Research and Development Co. Ltd., Tokyo (Japan)

1996-05-01

This paper reports the result of a preliminary circulation test conducted in fiscal 1995 on a deep reservoir (at a depth of about 2200 m) in the Hijiori hot dry rock experimental field. One water injection well and two production wells were drilled to constitute a circulation loop, to which the circulation test was performed to investigate the flow characteristics thereof. The result revealed the following matters: total amount of injected water of 51500 m{sup 3} resulted in a total fluid recovery rate of about 40%; as a result of well stimulation given twice during the initial stage of the water injection, the continuity impedance in the vicinity of the injection well decreased largely (however, the continuity improvement upon the second attempt was considerably inferior to that from the first attempt); and increase in the water injection amount does not necessarily lead to increase in the production amount. The paper describes additionally that it is extremely difficult to interpret non-linearity between the injection and production amounts by using a model prepared previously with a main objective to analyze the Hijiori HDR circulation system. 1 ref., 9 figs., 1 tab.

Development of more effective methods of normalization and application at braking in turn test; Senkai seido shiken no koritsuka to oyo han`i no kakucho shuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sekine, T; Nagae, H [Nihon University, Tokyo (Japan)

1997-10-01

Recant passenger cars have so higher grades of the cornering performance that the vehicle behaviors at braking in turn have become more important for the security on the obstacle avoidance ability. In this paper, the influences of amount of initial centripetal acceleration to braking motion of vehicles are discussed by experimental and theoretical analysis. Under the higher centripetal accelerations, even smaller deceleration bring the vehicle oscillating yaw velocity phenomena as same as centripetal accelerations. As to advance the effective test procedure. the authors proposed one of the methods that enable to reduce the test error by insufficient vehicle velocity. 7 refs., 6 figs., 1 tab.

Characterization on impact damage resistance of CF/PEEK laminates under low and high velocity impact tests; Teisoku/kosoku shogeki shiken ni yoru CF/PEEK no taishogeki sonshosei no hyoka

Energy Technology Data Exchange (ETDEWEB)

Morita, H; Hamamoto, A [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Adachi, T; Nishimori, K; Matsumoto, H [Tokyo Institute of Technology, Tokyo (Japan)

1995-04-15

Experiments were conducted to learn the impact damage on jet engine CFRP components for sucking birds or others. A great mass low velocity collision experiment using a falling weight and a small mass high velocity collision experiment using an air gun were conducted. The damages inflicted upon CF/PEEK (polyetheretherketone) laminates in the respective experiments were compared with each other by using the ultrasonic flaw detection method (C-Scan). There was a linear relationship in both experiments between the projected damaged area DA measured by C-Scan and the impact energy IE, enabling the relative evaluation of impact-withstanding damage characteristics by using the DA/IE ratios. DA/IE in the high velocity impact was higher than that in the low velocity impact, but the DA/IE ratio between the high velocity impact and the low velocity impact remained approximately the same, not dependent on the fiber orientation. The lamination parameter {beta} defined on the basis of the difference in-plane rigidity between the layers constituting the laminate is proportional to DA/IE, with {beta} enabling the generalized numerical expression of the impact of the fiber orientation upon the impact-withstanding damage characteristics. 9 refs., 5 figs., 2 tabs.

Sampling and preparation method for mutagenicity test of exhaust gas from municipal waste incinerator; Haikibutsu shokyakuro hai gas no hen`i gensei shiken no tameno shiryo saishu/chosei hoho

Energy Technology Data Exchange (ETDEWEB)

Yoshino, H. [Kanagawa Environmental Research Center, Kanagawa (Japan); Urano, K. [Yokohama National Univ. (Japan)

1994-09-10

It is well known that many kinds of hazardous organic compounds in incinerator exhaust gases. In this study, a simple sampling method to test mutagenicity on exhaust gases in flue and its extracting and its solvent converting methods by organic solvents were examined. In sampling 100 to 300 l at about 2 l/min in aspirating speed of the extract gases, the most of mutagenic substance were collected almost completely by condensed water and qualtz wool column. And, the collected materials into the condensed water could almost perfectly recovered by extracting the condensed water with about its one fourth volume of ethylacetate on vibrating once in 5 min., extracting the quartz wool column on flowing 20 ml of ethylacetate at the speed of about 3 ml/min., and others. After mixing such effluents and dewatering with about 5 g of sodium sulfate, they are evaporated out ethylacetate and resolved with 5 ml of dimethylsulfoxide (DMSO) to execute Ames mutagenicity test. As a result, more than about 3000 net rev./Nm{sup 3} of the mutagenicity was estmated on TA 98 strain. 9 refs., 5 figs., 8 tabs.

Investigations on sail force by full scale measurement and numerical calculation. Part 1. Steady sailing performance; Sail ryutairyoku ni kansuru jissen shiken to suchi keisan. 1. Teijo hanso seino

Energy Technology Data Exchange (ETDEWEB)

Masuyama, Y.; Fukasawa, T. [Kanazawa Institute of Technology, Ishikawa (Japan); Kitazaki, T. [DMW Corp., Tokyo (Japan)

1997-06-01

Sailing forces are measured with a 10.3m long full-scale sailing boat, equipped with a sail force dynamometer, CCD camera for sail shape measurement and an instrument for detecting sailing conditions of the hull, in order to obtain highly reliable performance data of a sailing yacht. The vortex lattice method is used for step-by-step numerical calculations, and the results are compared with the observed ones. The test results clearly show performance changing with slight changes in relative wind directions and sail shapes, which are not clearly obtained by the traditional wind tunnel tests. The calculated results, although deviating from the observed ones to some extent, well represent trends of performance changing with wind directions and sail shapes. In particular, changed performance caused by slight changes in draft at the main sail is clearly demonstrated. The numerical calculation is considered to be useful for searching for sail trim conditions. 17 refs., 18 figs., 1 tab.

1998 Annual Study Report. Standardization of corrosion resistance testing/evaluation methods for coated steel sheets; 1998 nendo seika hokokusho. Hyomen shori koban no taishokusei shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to develop the evaluation methods for reappearing corrosion characteristics of coated steel sheets in a short time, acid rain composition and artificial acid rain composition for the accelerated test were studied, and the cyclic corrosion tests were conducted. The literature survey shows that the main ionic species present in acid rain are Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, K{sup +}, NH{sub 4}{sup +}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, and Cl{sup -}, of which the acid rain components are SO{sub 4}{sup 2-} and NO{sub 3}{sup -}, their equivalent ratio (NO{sub 3}{sup -}/ SO{sub 4}{sup 2-}) in the Far Eastern area being 0.2 to 0.3. Therefore, the solution specified by ASTM 1141 is diluted 30 times with water to prepare the base solution for the accelerated tests, where its acidity is adjusted with a mixed acid of NO{sub 3}{sup -}/ SO{sub 4}{sup 2-} = 0.2 to 0.3 (pH: 3.0 to 4.0). Two sets of preliminary cyclic corrosion tests were conducted, one involving acid rain spraying, drying and humidification in this order, and the other acid rain spraying, humidification and drying. Analysis of the test data indicates that difference between these test cycles in corrosion rate is within a deviation range caused by different testing tools. Therefore, the former condition is adopted as the basis for the accelerated tests, because of its smaller deviation caused by different testing tools. (NEDO)

Report on results 1998. Standardization of test measuring method of fine ceramics for communication equipment; 1998 nendo seika hokokusho. Tsushin kikiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Technological development is in progress at present for the intelligent transport system for example that uses a microwave frequency range of 60GHz or 90GHz toward the practical use, with a demand increasing for measuring the electrical properties of fine ceramics (FC) to be used in the communication equipment of the system. The measuring method in the microwave frequency range of 30GHz or less is about to be standardized in IEC TC49/WG10; however, the method above 30GHz has not yet been examined for the standardization internationally. The subject research is intended to establish the method of measuring electrical properties such as the dielectric constant of FC for a high-frequency/ultra high-frequency wave range, dielectric loss and surface resistivity, to standardize the principle of their measuring methods, measuring tools, adjusting method of samples, procedures of measurement, etc., and to aim at the international standardization. This year, investigation and examination were carried out on various measuring methods including overseas examinations in the U.S., extracting the Fabry-Perot resonator method and a conductive cylindrical dielectric cavity resonator perturbation method for example, and evaluating the specifications of standard reference materials. In addition, a morphological technique was established for measuring sample surfaces affecting measurements, by means of an accurate measuring instrument for thin film surfaces. (NEDO)

Operation test for 200-kW class internally improved MCFC stacks having achieved 5000 hours; 200kW kyu naibu kaishitsu gata MCFC sutakku unten shiken 5,000 jikan tassei

Energy Technology Data Exchange (ETDEWEB)

Hashino, K. [Kansai Electric Power Co. Inc., Osaka (Japan)

2000-03-10

The operation test for 200-kW class internally improved MCFC stacks being performed at the Amagasaki fuel cell power generation testing plant of Kansai Electric Power Co., Inc. has achieved on January 22, 2000 five thousand hours, the original test time target. Temperature raising has begun on June 18 last year, and the first power generation was carried out on June 30. Since then the operation has continued smoothly at near rated output, and the test was completed nearly as planned without experiencing any trouble caused by Y2K problem. This research is being carried out as the research work shared by the Molten Carbonate Fuel Cell Power Generation System Technology Research Association (MCFC Research Association) based on the research commissioning from NEDO as part of the New Sunshine Project. After the confirmation of the initial performance, verification of the carbon dioxide self-sustaining operation, and the property evaluation test of every 500 hours are going smoothly. The intention hereafter is to achieve 5,000 hours as the power generation time, with the schedule to reduce the stack temperature in the middle of February, and cease the operation. As of January 25, the amount of power generated reached 1,089 MWh. (NEDO)

1998 Annual Study Report. Standards development of chemical analysis and non destructive inspection methods for pure titanium metals; 1998 nendo seika hokokusho. Jun chitan no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This study was conducted to standardize the chemical analysis and non-destructive inspection methods for pure titanium metals of industrial grade. These methods are among those serving bases for international standardization of products. The chemical analysis is aimed at quantitative analysis of trace impurities, in particular, present in pure titanium metals of industrial grade by developing and standardizing the inductively coupled plasma atomic emission spectroscopy, known for its low detectable limit, and, at the same time, spark and glow discharged atomic emission spectrometry as the improved routine analysis methods. These methods, although being used by, e.g., steel makers, have not been standardized because the effects of titanium-peculiar matrix are not elucidated. The non-destructive testing is aimed at standardization of the techniques useful for automatic production lines. More concretely, these include optical methods aided by a laser or CCD camera for plate surface defect inspection, ultrasonic methods for plate internal defect inspection, and pressure differential methods for air-tightness of welded pipes. They have not been used yet for automatic production lines. (NEDO)

FY 1994 Report on the feasibility study results of the geothermal exploitation technologies for the international joint demonstration research; 1994 nendo chinetsu tansa gijutsu no kaigai kyodo jissho kenkyu kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Described herein are the FY 1994 results of the feasibility study of the geothermal exploitation technologies for the international joint demonstration research with Indonesia. The survey methods are considered for the areas difficult to access by land transportation means (e.g., tropical rain forests) to promote development of geothermal resources in remote areas (small- to medium-scale geothermal power generation plans). The satellite and air remote sensing are used for the wide-area survey. The data obtained by the satellite are analyzed using the JERS-1 data, and then surveyed in detail by the air remote sensing for the selected areas to find, e.g., abnormal ground temperature regions, faults, volcanoes, geothermally altered regions and landslide regions. They are surveyed in more detail by the air electromagnetic and magnetic exploitation methods. Although they have high resolution, their application tends to be hindered by hot and humid climates in the prospective exploitation areas. The GEMS-aided resources analysis is used to establish the geothermal models, to help extract the promising areas. These techniques are basically common, but it is necessary to take into consideration, e.g., the environments and regional characteristics of these areas when they are actually used. Diversification of fossil fuel supply sources is advantageous for Japan, and her energy security will be improved by supporting geothermal resources development promotion in the supply sources. (NEDO)

Fiscal 1997 research report on the survey on public test and evaluation organizations for development of welfare equipment; 1997 nendo fukushi kiki kaihatsu ni kakawaru koteki shiken hyoka kikan chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This research studies the construction policy of public test and evaluation systems for future development and practical use of welfare equipment, through survey on the current methods for development, practical test and evaluation of welfare equipment in countries advanced in welfare, and preparation of basic data for promoting establishment of public test and evaluation functions in Japan. Infrastructure preparation for standards and public test and evaluation organizations for developing welfare equipment is being promoted by Technical Laboratory of Bicycle Industry Promotion Association and some national organizations such as Product Evaluation Technical Center, Mechanical Engineering Laboratory, National Institute of Bioscience and Human Technology, and Living and JIS Center. However, preparation of objective and across test and evaluation systems for developing welfare equipment is still insufficient. Product Evaluation Technical Center is now approaching to evaluation and standardization of welfare equipment. Public test and evaluation organizations of the UK, Sweden and Denmark are presented. (NEDO)

Fracture mechanical modeling of brittle crack propagation and arrest of steel. 3. Application to duplex-type test; Kozai no zeisei kiretsu denpa teisi no rikigaku model. 3. Konseigata shiken eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Aihara, S.; Tsuchida, Y. [Nippon Steel Corp., Tokyo (Japan); Machida, S.; Yoshinari, H. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1996-12-31

A proposal was made previously on a model of brittle crack propagation and arrest that considers the effect of crack opening suppression by using unbroken ligaments generated on steel plate surface and the effect that cracks precede in the central part of the plate thickness, based on a local limit stress theory for brittleness fracture. This paper discusses applicability of this model to a mixed type test, and elucidates causes for difference in the arrest tenacity of both types in a double tensile test of the standard size. The brittle crack propagation and arrest model based on the local limit stress theory was found applicable to a simulation of the mixed type test. Experimental crack propagation speed history and behavior of the arrest were reproduced nearly completely by using this model. When load stress is increased, the arrests in the mixed type test may be classified into arrests of both inside the steel plate and near the surface, cracks in the former position or arrest in the latter position, and rush of cracks into both positions. Furthermore, at higher stresses, the propagation speed drops once after cracks rushed into the test plate, but turns to a rise, leading to propagation and piercing. 8 refs., 15 figs., 3 tabs.

FY 1992 Research and development of ceramic gas turbines. Reliability demonstration tests for ceramic members; 1992 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai no shinraisei kakusho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-05-01

The creep rupture demonstration testing methods and non-destructive testing technologies are investigated for ceramic members, to promote development of ceramic gas turbines (CGT's), and the FY 1992 results are reported. For creep rupture demonstration testing methods, 3 types of silicon nitride as the CGT rotor materials are tested for tensile creep rupture at a rated temperature level (1200 degrees C) in the operating atmosphere (in the air), and applicability of the Larson-Miller method to ceramic members is investigated. It is found that Larson-Miller index, determined for each test temperature, is useful for explaining the test results, and analysis of the data by the Larson-Miller method is applicable to prediction of creep rupture life for specific members. For the non-destructive testing technologies to be applied to CGT members, the studied items include determination of white X-ray absorption coefficient by the film method and optimization of X-ray photographing, and the good results are produced. (NEDO)

Result of comparative experiment on environmental comfort in room using hot heat environment testing unit. Onnetsu kankyo shiken unit ni yoru shitsunai kankyo no kaitekisa no hikaku jikken kekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujiwara, T; Kawashima, K [The Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1991-11-20

Measurements were carried out on three buildings having different heat insulation, airtightness and heat capacity for testing the hot heast enviroments (having a room size of about 4.6 m{times}3.7m{times}2.3 m) as to the temperature differences between the upper and lower parts of the room and the MRT (mean radiation temperature, representing the temperature of radiation from the wall face). These are compared according to types of heating appliance. The result is summarize as follows: The temperature difference in the upper and lower parts is affected largely by the airtightness of the building, the difference being capable of getting reduced by rasing the airtightness even in a buildings low in heat insulation. In a building with low airtightness, type of heating appliance and its installation location affect the temperature difference. The MRT is determined determined nearly completely by the heat insulation of the wall face in a room, but it tends to be affected easily by the specification and area of windows. A floor heating system increases the MRT and generates very little difference in temperatures in the upper and lower parts of the room. A comparison using a PMV (one of the indexes for enviromental comfort in a room) was also conducted. 12 figs., 7tabs.

Fracture mechanical modeling of brittle crack propagation and arrest of steel. 3. Application to duplex-type test; Kozai no zeisei kiretsu denpa teisi no rikigaku model. 3. Konseigata shiken eno tekiyo

Energy Technology Data Exchange (ETDEWEB)

Aihara, S; Tsuchida, Y [Nippon Steel Corp., Tokyo (Japan); Machida, S; Yoshinari, H [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

1997-12-31

A proposal was made previously on a model of brittle crack propagation and arrest that considers the effect of crack opening suppression by using unbroken ligaments generated on steel plate surface and the effect that cracks precede in the central part of the plate thickness, based on a local limit stress theory for brittleness fracture. This paper discusses applicability of this model to a mixed type test, and elucidates causes for difference in the arrest tenacity of both types in a double tensile test of the standard size. The brittle crack propagation and arrest model based on the local limit stress theory was found applicable to a simulation of the mixed type test. Experimental crack propagation speed history and behavior of the arrest were reproduced nearly completely by using this model. When load stress is increased, the arrests in the mixed type test may be classified into arrests of both inside the steel plate and near the surface, cracks in the former position or arrest in the latter position, and rush of cracks into both positions. Furthermore, at higher stresses, the propagation speed drops once after cracks rushed into the test plate, but turns to a rise, leading to propagation and piercing. 8 refs., 15 figs., 3 tabs.

Studies on the mechanical behavior of rock anchors. ; Results of in-situ pull-out tests. Rock anchor no rikigaku kyodo ni kansuru kenkyu. ; Gen prime ichi shiken ni okeru anchor no kyodo

Energy Technology Data Exchange (ETDEWEB)

Arimoto, K.; Ebisu, S.; Nakagawa, M.; Usui, M.; Someya, T.; Machida, N. (Okumura Corp., Tokyo (Japan))

1991-10-31

The rock anchor method is planned to apply to some permanent structures but since this method was developed for temporary structures, the clarification of the transferring mechanism of force from an anchor to a rockmass, the fracture mechanism and the development of the dynamic model have not been established. This paper arranged the data obtained by a full-scale, in-situ pulling out test of a rock anchor as the first step to understand the dynamic behavior and analyzed by paying attetion to the modulus of deformation of the rockmass where the anchor was embedded to elucidate the affecting degree of rockmass modulus of deformation, the embedded length and the tendon diameter on the dynamic behavior of the anchor. The rock anchor behavior could be expressed accurately by applying a theoretical solution derived by the balancing condition of forces at the boundary face. Especially, when the rockmass is uniform and the fracture occurrs at the interface between the tendon and grout, this approach can express the fracture with the accuracy similar to that made by the finite element method. 6 refs., 11 figs.,1 tab.

Development of two-stage compression heat pump for hot water supply in commercial use. Establishment of design method for water and air heat source system; Gyomuyo nidan asshukushiki kyuto heat pump no kaihatsu. Suinetguen oyobi kuki netsugen sytem no sekkei hoho no kakuritsu

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, H; Hashimoto, K; Saikawa, M; Iwatsubo, T; Mimaki, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1996-07-01

The two-stage compression cascade heating heat pump cycle was devised for hot water supply in business use such as hotel and store use which allows hot water supply less in primary energy consumption than gas boilers, and higher in temperature than conventional heat pumps. This cycle heats water in cascade manner by two-stage compression using two compressors in both low- and high-stage refrigerant circuits, and two condensers different in condensation temperature (intermediate heat exchanger and condenser) to achieve higher hot water temperature and higher COP. For cost reduction, the new system design method was established which is possible to cope with conventional compressors such as screw and scroll ones with different theoretical suction volume for every one. System design parameters such as thermal output and COP of hot water supply were largely affected by theoretical suction volume ratio of low- and high-stage compressors dependent on combination of the compressors, and refrigerant condensing temperature in an intermediate heat exchanger as proper parameter. 4 refs., 17 figs., 13 tabs.

On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

Energy Technology Data Exchange (ETDEWEB)

Yago, K; Endo, H [Ship Research Inst., Tokyo (Japan)

1997-12-31

The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

FY 1993 report on the survey of geothermal development promotion. Jetting/reduction test (No.36 - Amemasu-dake area); 1993 nendo chinetsu kaihatsu sokushin chosa. Funshutsu kangen shiken hokokusho (No.36 Amemasu dake chiiki)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-10-01

As a part of the survey of geothermal development promotion, the jetting/reduction test using a structure drilling well N4-AM-4 was made in the Amemasu-dake area, Hokkaido, survey was conducted of the state of jetting of geothermal fluid, the state of borehole, analysis of geothermal fluid, etc. The induced jetting was carried out by the Swabbing method in the total number of times of 97 in 10 days. As to the jetting of geothermal fluid, jetting was recognized in a short time from 2 hours 49 minutes to 3 hours 51 minutes, but did not result in the continuous jetting. The mean jetting amount of geothermal fluid was totally 4.03 t/h (0.69 t/h in steam flow and 3.34 t/h in water flow). The temperature of geothermal water while jetting was 90 degrees C, pH was 8.6-8.9, chlorine ion concentration was 520-960 ppm, and electric conductivity was 2.41-3.57 ms/cm. The pressure at the feed point while stopping jetting was 5,800 MPa, and the pressure just before stopping jetting was 1,191 MPa. Chemical components in geothermal water belonged to the alkali C1 type. The geochemical temperature of geothermal water by Na-K temperature was 229 degrees C at maximum and 202 degrees C at minimum. (NEDO)

On the hydroelastic response of box-shaped floating structure with shallow draft. Tank test with large scale model; Senkitsusui hakogata futai no harochu dansei oto ni tsuite. Ogata mokei ni yoru suiso shiken

Energy Technology Data Exchange (ETDEWEB)

Yago, K.; Endo, H. [Ship Research Inst., Tokyo (Japan)

1996-12-31

The hydroelastic response test was carried out in waves using an approximately 10m long large model, and the numerical analysis was done by the direct method, for a commercial-size (300m long) box-shaped floating structure with shallow draft. The scale ratio of the model is 1/30.8, and the minimum wave cycle is around 0.7s from wave-making capacity of the tank, which corresponds to 4 to 14s with the commercial-size structure. Elastic displacement and bending strain were measured. The calculated results by the direct method are in good agreement with the observed results. The fluid dynamic mutual interference effects between elements are weak in added mass but strong in damping force, indicating that the range of mutual interference is strongly related to rolling cycle in the range of mutual interference. Wave pressure on the floating structure bottom is high at the upper side of the wave, greatly damping towards the downside of the wave. However, response amplitude of elastic displacement tends to increase at the ends, both in upside and downside of the wave. For the floating structure studied, the 0 to 4th mode components are predominant in longitudinal waves, and the 6th or higher mode components are negligibly low. 21 refs., 15 figs., 2 tabs.

Fiscal 1999 geothermal energy development promotion survey. Survey of Akinomiya area (Long-term spurt test report - 1/2); 1999 nendo chinetsu kaihatsu sokushin chosa Akinomiya chiiki chosa hokokusho. 1/2. Choki funshutsu shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-01-01

A long-term survey was conducted on the spurting properties and fluid properties of geothermal fluids, when boreholes N9-AY-3 and N10-AY-8 were used as spurting wells and N8-AY-1, N10-AY-6, and N10-AY-7 as reinjection wells. Conducted or investigated were pH, electric conductivity, chlorine concentration determination, static temperature/pressure logging, PTS (pressure, temperature, spinner flowmeter) logging with wells spurting, buildup test, sampler logging with wells spurting, fluid property survey, tracer test, and borehole N10-AY-8 pulsation with fume spurting. It was then found that the maximum spurting capacity of borehole N9-AY-3 was 65.7t/h in steam and 90.8t/h in thermal water at a pit mouth pressure of 1.30MPaG. Some decrease was detected for approximately one month after the start of spurting, but it was concluded that there would be no further decrease thereafter. The maximum spurting capacity of borehole N10-AY-8 was 10.4t/h in steam and 8.9t/h in thermal water at a pit mouth pressure of 0.24MPaG. Some reduction was detected in the flow of steam and in fluid enthalpy after the start of spurting, and it was inferred that there would be still further reduction after continual spurting. (NEDO)

Research report of FY 1996 on development of new hydrogen energy demonstration technology. 2. Results in the extension period of FY 1996; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo kikan enchobun)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat measurements were conducted through the excess heat confirmation tests using a fuel cell-type electrolytic cell up to November 1997. As a result, it was found that the excess heat measured by the calibration method can not be measured by the flow calorimetric method. In order to investigate the possibility of systematic errors of the both methods, the sensitivity, accuracy and responsibility, and the conditions of the excess heat generation, research activities based on new facts from scientific information and fundamental research supporting projects have been mainly performed. Among these, were performed the excess heat measurement tests by the cataphoresis method, absorption tests by the high-pressure and high-temperature charging method, gas plasma loading, in-situ X-ray detection, and reactant detection tests using Au/Pd/PdO heterogeneous structural body. 5 refs., 59 figs., 9 tabs.

Subsidized project for development of technology in putting photovoltaic power generation system into practice. Report of international joint demonstrative R and D on photovoltaic power generation system; Taiyoko hatsuden system kokusai kyodo jissho kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The following joint researches are in progress utilizing natural conditions and social systems in Nepal, Mongolia, Thailand, Malaysia and Vietnam for the purpose of enhancing environmental adaptability, reliability, etc., of technologies. (1) Nepal; accelerated demonstrative research utilizing highland conditions, (2) Mongolia; demonstrative research of movable type photovoltaic power generation system, (3) Thailand; demonstrative research of photovoltaic generation system for battery-charging stations, (4) Malaysia; accelerated demonstrative research utilizing tropical conditions, and (5) Vietnam; demonstrative research of hybrid system on photovoltaic power generation and micro hydro power generation. The research assets of (1) and (3) whose researches have been finished were provided gratis for the co-researcher countries. In (5), on the basis of the geographical conditions such as annual average quantity of solar radiation, conduit for water-turbine, energy complementing relation, load demand, and degree of installation difficulty, Trang Village in Vietnam was selected, with a system decided on PV:100 kW/MH:25 kW/control system. The MH is an induction generator. The primary pieces of equipment are a generator, a storage battery, an inverter and a system control panel. (NEDO)

Achievement report for fiscal 1998. Research and development of ceramic gas turbine (Reliability verification test for ceramic members); 1998 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai no shinraisei kakusho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

For a ceramic gas turbine to achieve efficiency of 42%, materials capable of withstanding approximately 1300 degrees C are required. In fiscal 1998, the mechanism of creep deformation and life prediction are studied, with specimens exposed to a short-term high-stress conditions equivalent to a time to fracture of 1000h. It is known after studies in the past that, under a stress of approximately 240Mpa, the logarithmic values of the load stress and time to fracture may be described by two differently inclined straight lines. Strain is accurately measured by use of a CCD camera for the determination of a creep curve, and then stress indexes are worked out. It is then found that the stress indexes are 4 on the lower stress side of 260MPa and 11 on the higher stress side of the same. This enables the extrapolation of short-term creep fracture data for the prediction of long-term life. No large-scale reduction in resistance to creep due to changes in the crystal phase is not predicted. Longitudinal sound wave speeds are measured, and the result manifestly describes how the longitudinal sound wave speed slows down with the progress of creepage in the material. Reference is also made to international reports about the study of ceramics performance tests and evaluation methods, international joint studies about mechanical properties tests, and the international round robin test of material powder. (NEDO)

Report on achievements in fiscal 1998. Demonstrative research of an alkali recovery process in the non-wood pulp paper manufacturing industry; 1998 nendo himokuzai pulp seishi sangyo arukari kaishu process ni kakawaru jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This project is intended of performing demonstrative research jointly with China on a system to efficiently extract, condense, and combust black liquor in a non-wood pulp paper manufacturing plant in China to recover alkaline solution and heat energy, and to contribute to proliferation of the system. Specifically, an alkali recovery plant is built in Cangshan Paper Making Plant in Shandong Province to verify conservation in energy and reduction environmental load. This fiscal year has performed (1) component researches and related technology investigations, and (2) device design and fabrication. For Item 1, the extractor adopted the spiral net type, and the condensation device adopted the falling film evaporator of full-can plate type. For the silica removing agent, data were acquired on reduction of silica in the black liquor and effect of reducing the black liquor viscosity. Basic design requirements were established for an alkali recovery process for a pulp production plant of 75 t/d. Regarding Item 2, prepared were the material and heat balance tables for the black liquor extractor and the black liquor condenser, process flow diagrams (PFD), device specifications, a meter list, and a summary utility consumption list, and confirmed them with the Chinese side. For the black liquor combustion device and the caustification device, PFD and device list prepared by the Chinese side were acquired to start the basic design. (NEDO)

Report on the fiscal 1996 result of the research on the promotion scheme toward establishment of an international cooperation system for development of welfare equipment; 1996 nendo chosa hokokusho fukushi yogu kaihatsunado no kokusai kyoryoku taisei kakuritsu ni mukete no suishin hosaku no kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In order to support the progress and international activity of a Japanese welfare industry, research was made on a concrete approach to establishment of a Japanese international cooperation system on the basis of the activity trend of welfare organizations and groups in North European countries and Japan. Introduction of standards and a mark system for welfare equipment is under investigation in North European countries, and movement for unified standards is also becoming active among these countries. TIDE project called socioeconomic integrated engineering already exists for handicapped and aged persons in Europe, while a rehabilitation act was enforced in the U.S.A. in 1973. Japan participated in ISO and IEC for promotion of a welfare equipment industry. Rehabilitation Engineering Society of Japan (RESJA) for equipment development and technical support, and Japan Wellness and Welfare Industry Association (JWA) for promotion of the related industries were also established. In Europe, North America and Australia, rehabilitation engineering associations are already in action. 8 figs., 17 tabs.

New energy vision in Sawauchi Village area. Toward establishment of Sawauchi Village having unaided power based on 'new energies, lessons learned from past'; Sawauchimura chiiki shin energy vison. 'Onkochi shin energy' ni yoru jiriki aru Sawauchimura no kakuritsu ni mukete

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

A new energy vision was established in the Sawauchi Village area in Iwate Prefecture. As the energy species to be discussed for introduction, Sawauchi Village has assumed 'solar (beam and heat)', 'forest bio-mass', 'stock breeding bio-mass', 'small hydro-power' and 'snow'. The new energy introduction project included the proliferation and enlightenment activities using the Snow Country Culture Research Institute as the core, new energy introduction into the Sawauchi Baden, introduction of small hydropower generation and micro hydropower generation, new energy introduction into snow melting systems, new energy introduction into agricultural greenhouses, introduction of snow room-cooling systems into public facilities, development of new business targeted at promotion of forestry, and proliferation and enlightenment activities coordinated with relevant organizations. Particularly in the development of new business targeted at promotion of forestry, tackling will be moved forward to sale and manufacture of pellet stoves, manufacture of wood pellets, research, development, and commercialization of bio-mass power plant and new housings incorporating snow country cultures, with an aim of promotion of utilization of woods and thinned woods available in the village. (NEDO)

Report on the achievements in the Sunshine Project in fiscal 1988. Development of a coal liquefaction technology (Liquefaction performance test on Chinese coals); 1988 nendo sekitan ekika gijutsu kaihatsu, Chugokutan ekika seino shiken seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

Development has been carried out on a Chinese coal liquefaction technology jointly by Japan and China. The Japanese side fabricated and built a small continuous testing equipment. Shenbei coal produced in Liaoning Province, Tienju coal produced in Gansu Province and Shenmu coal produced in Shaanxi Province were used as test sample coals. These coals were crushed, washed with water, sorted, dried, pulverized below 100 mesh, and used as the test samples. For catalysts, a reagent Fe{sub 2}O{sub 3} and S as an auxiliary catalyst made in China were used. Anthracene oil freed from crystal was used as a starting solvent when making one-through operation and recycling operation. Hydrogen used had purity of 99.5% or higher. The current fiscal year has performed smoothly to the end either of the one-through operation or the solvent circulating operation on RUN-2200, 2300 (Chenbei coal) and 2,400, 2500 (Tienju coal). Operation of 2600, 2700 (Shenmu coal) experienced noise in the stirrer of the reactor, and leakage of the circulating gas from the recycled gas compressor. In addition, the differential pressure during operating the last run has increased to 50 k, when the temperature and pressure were reduced, and substances clogging the reactor inlet line were removed. Three kinds of the liquefied oils were brought back to Japan for detailed analyses. (NEDO)

Achievement report for fiscal 1991. Research and development of ceramic gas turbine (Verification test on reliability of ceramic members); 1991 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai no shinraisei kakusho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-05-01

Development has been advanced on a test method to verify reliability of ceramics members being the basic material. Specifically, discussions were given on 1) the creep fracture verification test method, and 2) non-destructive test methods applied to different parts of the CGT. In Item 1, tension creep rupture tests were given on three kinds of candidate materials (Si{sub 3}N{sub 4}) used in the rotors in the atmosphere and the rated temperature zone. The fatigue resistance coefficient and the stress coefficient from several hours to 1,000 hours were calculated from the analysis of rupture time relative to temperatures and load stresses and elongation of the test pieces. It was verified that the test results can be put into order by using coefficients derived by test temperatures. The temperature was centered around 1,200 degrees C, and the load stress was varied from several ten to several hundred MPa. In Item 2, development was made on a theory to quantify the ultrasonic effective beam diameter by using the reflective echo heights, making it possible to make the ultrasonic flaw detection method into a theorem. Defects with sizes from 70 to 200 {mu} m can be estimated with error rates from 10 to 20%. (NEDO)

Fiscal 1994 achievement report. Development of entrained bed coal gasification power plant (Part 5 - Survey of demonstration plant); 1994 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 5. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

A survey was conducted of a demonstration plant for developing the technology of integrated coal gasification combined cycle power generation. In fiscal 1994, based on the studies of pilot plant operation conducted up to the preceding fiscal year and on the studies of a demonstration plant (conceptual design of a demonstration plant), systems were examined for still higher performance and economical efficiency. For optimizing the heat source for pulverized coal drying air, an extracted air heat utilizing system was adopted, excellent in performance (approximately 0.5% improvement in absolute value) and in economical efficiency. For reducing the consumption of inert gas for the fluidized bed desulfurization facility, an approximately 30% reduction was found to be possible dependent on gas regeneration conditions in the regeneration tower. For performance improvement with the combined cycle equipment placed under a partial load, the generating-end efficiency was improved approximately 0.2% when only SGC (syngas cooler) was loaded 80% or less and kept at a constant pressure. Studies were also made about how to maintain a constant output with the equipment exposed to air temperature changes. (NEDO)

55th electric science promotion prize (progress prize). Demonstration of optical soliton transmission on OPGW first in the world; Dai 55 kai denki gakujutsu shinkosho (shinposho) jusho. Seiaihatsu no OPGW ni okeru hikari soriton denso no jissho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-10

Electric science promotion prize (progress prize) is given to `Person who newly proposed a new concept, theory, material, device, system and method on electrical science and technology, or demonstrated these proposals` by the commendation committee of Institute of Electrical Engineers of Japan every year. Eight promotion prizes including that for Kansai Electric Power`s `Demonstration of optical soliton transmission on OPGW first in the world` were given. This research succeeded in development of the transmission/ receiving device suitable for optical soliton transmission, and the prediction method of an optimum transmission condition by computer simulation. In addition, this research succeeded in 10Gbit transmission of 784km and 40Gbit transmission (4-wave multiplex) of 392km by applying the above research result to Okurobe trunk line OPGW (98.2km). This demonstration of optical soliton transmission on OPGW is first in the world. (NEDO)

Fiscal 1999 international energy conservation model project. Report on result of demonstrative research concerning cement clinker cooling system; 1999 nendo kokusai energy shohi koritsuka nado model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing energy consumption and CO2 discharge in a cement plant in Indonesia, R and D was conducted on new clinker cooling system, high performance kiln combustion system, and technology for steady kiln operation and control, with the fiscal 1999 results reported. In the research on the optimum clinker cooling system, a new type clinker cooling system (CCS) was developed in which air beams are applied only to stationary grate rows, in an air beam type clinker cooling system where cooling air is fed to each block, with grate plates used as the air duct. This year, in an actual machine testing equipment (capacity 2,500 t/d), the whole heat recuperation area was modified for the CCS, with the operation started since February, 1999, aiming at the optimal clinker cooling effect and high heat recovery efficiency. The heat quantity for the entire system showed a decrease of 60 kcal/kg in the heat consumption rate through CCS modification, kiln burner adjustment, etc. So long as the demonstration plant is concerned, design of a new type burner and study/design for the kiln stabilization were nearly completed. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating pure titanium; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Jun titan no shiken hyoka hoho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of submitting propositions to ISO (International Organization for Standardization)/TC79 (Light metals and their alloys) and ISO/TC135 (Non-destructive testing), studies were made relating to the standardization of methods for chemical ingredient analysis and non-destructive testing of industrial pure titanium. In the development of an ingredient analysis method for pure titanium, performance standards and analytical allowance were determined for an inductively coupled plasma emission spectrochemical analyzer for vanadium, niobium, cobalt, and boron, which were short of completion in the preceding fiscal year. As for spark discharge emission spectrochemical analysis, analysis methods were newly established for oxygen and hydrogen. In the development of optical flaw detection for pure titanium boards, the quality of test pieces were determined by use of a reference test piece, and studies were made about the kinds of artificially produced flaws and a method for sensitivity calibration. In the development of ultrasonic flaw detection for pure titanium boards, studies were made about the effects of board thickness, kinds of flaws, and of board size. Using the findings, a draft standard was prepared in Japanese for a JIS (Japanese Industrial Standards) proposition and another in English for an ISO proposition. (NEDO)

Fiscal 1998 geothermal development promotion research. Survey in Akinomiya area (N9-AY-3 short-term blowout test report); 1998 nendo chinetsu kaihatsu sokushin chosa. Akinomiya chiiki chosa (N9-AY-3 tanki funshutsu shiken hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the fiscal 1998 geothermal development promotion survey in Akinomiya area, this test was carried out to obtain the fumarolic gas characteristics and fluid properties of N9-AY-3 test well by air reaction method. Blowout hot water was reinjected to N8-AY-1 test well drilled in fiscal 1996 to confirm its reinjection capacity. The fumarolic gas test result showed a steam volume of 35.0t/h and hot water volume of 160.8t/h (wellhead pressure equivalent) at a wellhead secondary valve opening of 33.7% and wellhead pressure of 15.3kg/cm{sup 2}G. The whole hot water volume of 30,214m{sup 3} is equivalent to nearly 320 times more than a well volume. Hot water showed pH7.7-8.6, an electric conductivity of 3,960-7,070{mu}S/cm, and chlorine ion concentration of 1,050 mg/l. Alkalescent Na-Cl system hot water showed a geochemical temperature of 283 degreesC. A steam gas concentration including CO{sub 2} as main component was 0.12-0.19vol%. Blowout hot water was continuously reinjected into N8-AY-1 well from a pit by pump to confirm its reinjection capacity. The reinjection capacity of hot water in fumarolic gas was 110t/h without any problem. (NEDO)

Fiscal 1995 survey report on the environmentally friendly type coal utilization system introduction support project. Verification project on the circulating fluidized bed boiler; Kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudosho boiler ni kakawaru jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

In relation to the circulating fluidized bed boiler which reduces the amount of sulfur oxides emitted in coal utilization, a verification project was carried out on installation of the equipment and spread activity in China and the Philippines contributing to the control of environmental pollutant associated with coal utilization and the effective use of energy. At the Fanshan area, installed was a 10t/h internal circulating fluidized bed boiler. At the performance test, coal includes around 7% of impurities such as stone, and the impurities should be excluded continuously at the time of actual run. Therefore, the boiler efficiency had to be changed from 89.5% to 85.8%. Further, power generation facilities have not yet been finished, and the overall operation of boiler turbine has not been executed. At the Zibo area, a 30t/h external circulating fluidized bed boiler was installed. The boiler efficiency reached 86.1%, over the targeted value. At the Batangas area in the Philippines, a 10t/h internal circulating fluidized bed boiler was installed. The boiler efficiency reached 85.8%, over the designed value. About the coal produced in the Philippines, slagging was feared, but the combustion state was favorable. 82 figs., 21 tabs.

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 5 - Surveys and studies of demonstration plant); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 5. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Surveys and studies were conducted concerning a demonstration plant for establishing the technology of integrated coal gasification combined cycle, and the fiscal 1995 results are compiled. In this fiscal year, a demonstration plant conceptual design was prepared for assuring smooth transition from a pilot plant to a commercial plant. The design followed the system employed at the Nakoso pilot plant for its gasification power generation. It was decided that the gasification furnace be of the air-blown (oxygen enriched) 2-stage entrained bed type, that the desulfurization system be of the dry type 2-stage fluidized bed type, the dedusting system be of the dry type granular bed type (moving bed type), that the combined cycle power facility be derived from the commercialized gas turbine, and that the cycle of the steam system agree with the integrated coal gasification combined cycle system now under discussion. Studies were made, which covered heat efficiency (generating end/sending end), heat/matter balance, process flow, gas turbine/steam system optimization, comparison in performance with a pilot plant with its dimensions increased, estimation of the performance of each of the facilities, estimation of the construction cost, calculation of the generation cost, environmental friendliness, operating characteristics, acceptable coal types, and the like. (NEDO)

FY 1998 Report on field test project study for introduction of high-performance industrial furnaces. Detailed measurement study of FY 1998 joint research demonstration data; Koseino kogyoro donyu field test jigyo. 1998 nendo kyodo kenkyu jissho data no shosaina sokutei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of measurement and study for introduction of the high-performance industrial furnaces. The NEDO's works for development of the high-performance industrial furnaces have been almost completed. The field tests are conducted to verify leveling and increasing temperature in the high-performance industrial furnaces. The data are collected in the existing and modified furnaces at the standard treating rate for each of the selected furnaces. The measured items are heat patterns of the works, temperature distributions within the furnace, heat balances in the combustion furnace, waste heat at the regenerative heat recovery unit, and exhaust gas components. The investigated items are names, materials, shapes, weights and quantities of the works; charging/discharging temperature; heating time; temperature in each furnace; consumption, types and heating values of the fuels used; air/fuel ratios; presence or absence of recuperator and its conditions when adopted; air temperature upstream and downstream of the heat accumulator, and exhaust gas temperature and components; temperature of the heat accumulator's external walls; cooling water rates, and inlet/outlet temperature, surface temperature of the furnaces' external walls; and furnace dimensions and structures. The measurements are done by thermocouples for various types of temperature, and O{sub 2}, CO2, CO, NOx meters and other analyzers for the components. The data are collected on a continuous basis. (NEDO)

Achievement report for fiscal 1999. Joint verification research on use for power generation of Omani superhigh-viscosity crude oil remaining unexploited; 1999 nendo Oman koku ni okeru miriyo chokonensei gen'yu no denryoku riyo ni kansuru kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A Mukhaizna oil field remains to be exploited in Oman, with an estimated reserve of 2.4-billion barrels of very heavy oil with an API (American Petroleum Institute) specific gravity of 15.3. The viscosity of the oil is so high as to be over 100-thousand cP (at 15 degrees C). The extremely high viscosity causes its exploitable rate to be so low as 3%, and makes shipment by pipeline quite difficult. In this survey, a method using water emulsion is proposed for viscosity reduction, which aims to reduce the Mukhaizna crude oil viscosity to 200mm2/s or less. In an experiment using the water emulsion method, oil is mixed with water at a rate of 72 to 28 in a shearing mixer for the production of a water emulsion of crude oil. It is found that a certain degree of stability is acquired using a surface active agent available on the market. Using this emulsion method, the crude oil is converted into a power generator fuel with a heating value of 6,775kcal/kg. The crude oil-turned product is a fine fuel superior to Orimulsion which is a fuel of the same type in terms of viscosity, amount of ash, and vanadium concentration. (NEDO)

Report on the achievement of verification for FY 1997-1999. Verification survey of a capacitor system for power leveling of the photovoltaic power generation; 1997 nendo kara 1999 nendo taiyoko hatsuden shutsuryoku heijunkayo capacitor system no jissho chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The purpose of this verification survey is to confirm the performance and reliability with which a new large capacity capacitor works as power leveling use and partial power peak shift back-up use in the photovoltaic power system. The results of FY 1997 are as follows: (1) Verification using jelly-role type cells. (2) Trial manufacture of stacking cells. In (1), jelly-role type cells were manufactured using an electrode composed of aluminum foil and activated carbon layer and the organic electrolyte. The obtained cell capacitance was 6,000F on average and the energy density 5.4-5.6Wh/L. The experiment on the constant power load of a capacitor bank constructed with four 6,000F cells connected in series was carried out to confirm discharge energy of 25Wh between 12V and 3V. In (2), stacking rectangular type cells were trially manufactured by the electrode composed of two types of electrode; press type and sheet type electrodes. The cell capacitance was approximately 3,500F at sheet electrode cell, and the energy density 7.2Wh/L. To improve the cell performance, a relation was studied between the pore distribution of activated carbon and the double layer capacity, and the material higher than the conventional one in capacity per volume was found out. Studies were also made of trial fabrication of charge/discharge circuits and the experiment and the voltage balance. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

Achievement report for fiscal 1993 on developing entrained bed coal gasification power plant. Part 5. Survey and research edition for demonstration plant; 1993 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 5. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-01

With an objective of developing the coal gasification composite power generation technology, surveys and researches have been carried out on a demonstration plant. This paper summarizes the achievements in fiscal 1993. Based on the achievements having been obtained by the previous fiscal year, the current fiscal year has discussed the method for evaluating the up-scaling, and performed a conceptual design of the demonstration plant. In discussing the demonstration plant in the current fiscal year, identification was made on the basic performance characteristics as the IGCC (atmospheric temperature characteristics, coal type change characteristics, partial load characteristics, methods for plant actuation and shutdown, and utility use amount), and selections were conducted on different systems to be adopted in the demonstration plant, both based on the approximate thermal material balance having been derived in the previous fiscal year. The results of the discussions were summarized as the steam cycle discussion, performance discussion by coal types, partial load characteristics, atmospheric temperature characteristics, secondary air temperature characteristics, discussions to enhance efficiency and reliability in association with the up-scaling, discussions on the utility facilities, discussions on the protection interlock, and forecast on the entire performance according to the approximate thermal material balance. (NEDO)

Promotion of the formation of environmentally friendly energy community (FY 2000). Demonstration of the gas turbine repowering waste combined power generation technology; 2000 nendo kankyo chowagata energy community keisei sokushin seika hokokusho. Gas turbine repowering haikibutsu fukugo hatsuden gijutsu jissho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demonstrative operation was conducted of the super waste power generation system in which the low temperature steam generated in waste incinerator is raised in temperature using the combustion exhaust gas emitted after the power generation using another gas turbine for conducting the steam turbine power generation with high efficiency. The FY 2000 results were summed up. In the demonstrative operation, operation and data acquisition/analysis were conducted following the previous fiscal year by 25MW class gas turbine repowering waste combined power generation facilities (Takahama power plant). Further, four years after the start of operation, the secular variation was studied by disassembly/inspection of equipment. As a result of the operation, the thermal efficiency was approximately 35%, much higher than the existing waste power generation. It was verified that the power system was maintained by the same maintenance as that of the ordinary power system. Moreover, the important point of this system is that no special corrosion resistant materials are used and that the high-efficiency waste power generation was demonstrated by combining the existing equipment. It can be said that the super waste power system has high qualities for forming energy community as a regionally dispersed stabilized power source. (NEDO)

Reports on 1979 result of Sunshine Project. Testing research for detailed design of solar thermal power generation plant (tower converging method); 1979 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-31

This report briefly describes first, in the summary of the results, the contents of the research results of the year with the outcome as the central point. Then, it explains in detail, in the contents of the research, the substance of each research item, results, their examination contents, and future research subjects. The objective of the research is, for the purpose of technically seeking the cost performance of a solar thermal power generation plant, (1) to develop equipment constituting the plant and (2) to develop a pilot plant having an electrical output of about 1,000kW at the peak by the tower converging method. The research results were as follows. (1) In the confirming test of a heliostat test unit, the final conclusion was obtained of the wind resistance calculated value by the wind tunnel test of the heliostat; the design materials of the assembly jigs were obtained; the data of the operation forecast was obtained in a tracking test; and a sensor was developed for the tracking instrumentation. (2) In the confirming test of the improved absorbing surface/mirror, the improvement/trial production including the manufacturing method was carried out as the absorbing surface for the actual unit. (3) In the heat collecting test, steam generation and a loop control test were performed. (4) The plant system was analyzed, with data obtained for the operating method. (NEDO)

Study on utilization of shallow sea areas by developing the alga field. Test for utilization of coal ash on alga reef (interim report); Sojo zosei ni yoru asakaiiki riyo no kenkyu. Sekitanbai kokabutsu no sosho riyo shiken (chukan hokoku)

Energy Technology Data Exchange (ETDEWEB)

Tsuno, M.; Oikawa, M. [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Matsubara, T. [Hokkaido Area Management and Support Foundation, Sapporo (Japan)

1996-03-25

A development was intended of an alga reef block that is suitable for adherence of algae and difficult of shore-burning by utilizing coal ash. Concretes with different coal ash displacement rates were used to install alga reef blocks embedded with natural rocks, steel plates, and the used desulfurizing agents on three areas (the Usubetsu area, the Tamagawa offing, and Chatsu Bay) including shore-burned sea areas along the coast of Tomari Village. Investigations were made on the states of adherence of useful algae as a result of difference in materials and locations of installation. The best adherence of edible kelp was observed at the Usubetsu area, followed by the Tamagawa offing and Chatsu Bay in that order. Growth conditions of the kelp by locations were conceived of the correlation with how extensively the natural kelp colonies are formed around each location, and how many nutrient salts are present and sea urchins are grown. No remarkable difference was observed in the adherence of algae due to the difference in the coal ash displacement rates. Porous blocks, however, showed less adherence amount. Kelp adherence condition was found good in the order of concrete, natural rocks, and the used desulfurizing agents. No kelps have adhered on the steel plates. 10 refs., 13 figs., 3 tabs.

Fiscal 1995 achievement report. Development of entrained bed coal gasification power plant (Part 3 - Pilot plant operational test - 2/2); 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken hen (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The 200 tons/day entrained bed coal gasification pilot plant constructed for establishing the technology of integrated coal gasification combined cycle was subjected to operational tests, and the fiscal 1995 results are detailed. During Runs D13, D14, E1, D15, and A14 in the operational test of the gas clean-up facility (dry type dedusting facility), 10 troubles occurred, including damage of the separator screen, leak in the seal valve, and leak of the expansion gas, and measures were taken to deal with each of the troubles. The results of the gas turbine facility operational test were satisfactory, without any trouble worth discussion. In the operational test of the safety/environment-related facility, it was found that the produced gas was stably incinerated and that denitration performance during gas turbine operation roughly achieved the intended level. In the operational test of electric and control facilities, an overall test was conducted, inspection was made of the indoor switching facility, etc., and 13 improvements were made, which included the alteration of the high ANN setting in the water tank for slag, the alteration of the mill exit temperature setting for enabling the use of Taiheiyo coal, and proper methods for carrying out high-load operation. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the fine bioceramics testing/evaluation methods; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seitaiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of the fatigue characteristics of the bioceramics, fatigue and impact-resistance characteristics of the members of these materials, and methods of evaluating their compatibility with a living body, for proposing the international standards. The test results of alumina and zirconia as the bioceramics indicate that their bending fatigue characteristics greatly depend on environmental conditions and frequency, suggesting necessity for the evaluation in the environments which simulate the living body inside. The compression and impact tests are conducted for the artificial femoral heads with a taper. It is found that the simulated body fluid, having the dissociated ion concentration adjusted at the level in the human blood plasma, remains unchanged in the concentration at 36.5 degrees C for 4 weeks; the ion concentration is unaffected by filtration with the aid of the microfilter useful for, e.g., removal of bacteria; and the synthetic apatite has almost the same composition as that for the bones in a living body. It is also suggested that activity of the bioactive ceramics can be evaluated by their ability for forming apatite in the simulated body fluid. (NEDO)

Test and research on the production of useful matter with carbon-dioxide-fixed microorganisms. Production of biodegradation plastics with photosynthesized microorganisms. Tansan gas kotei biseibutsu wo mochiita yuyo busshitsu seisan shiken kenkyu. Kogosei biseibutsu ni yoru seibunkaisei plastic seisan

Energy Technology Data Exchange (ETDEWEB)

Miyasaka, H. (The Kansai Electric Power Co. Inc., Osaka (Japan))

1994-07-10

The present report introduces the basic research on the production of PHB (one of the biodegradation plastics) by utilizing the photosynthesized microorganisms. The indigo algae are conveniently used for the genetic operation, because they are genetically inferior and have plasmid (extranuclear ringed DNA). Therefore, a certain type of oceanic indigo algae was used for the present research. As a vector to introduce the PHB-producing gene into the indigo alga cell, hybrid plasmid was prepared by combining the indigo alga plasmid pAQ1 with colon bacillus plasmid vectors pUC19. The thus prepared vectors had an introduction efficiency into about 1000 cells per one vector. A RuBisCO gene of indigo alga cell was selected as a promoter to heighten the activity of PHB-producing gene in that cell. The gene is being further studied in promotion efficiency by combining it with the above vector and PHB-producing gene. 4 figs.

FY 1977 Annual report on Sunshine Project results. Experimental research for detailed designs of tower light-collection type solar thermal power plant; 1977 nendo taiyonetsu hatsuden plant (tower shuko hoshiki) no shosai sekkei no tame no shiken kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

This project is aimed at pursuing technical and economic possibilities of solar thermal power plant by development of devices for a tower light-collecting type solar thermal power plant (in particular, heliostat, heat absorber and heat storage device) and materials therefor through the basic tests, and tests using a 10 kW heat collector and construction, on a trial basis, of a large-scale model plant with a commercial heliostat, and by planning to construct a 1,000 kW-class pilot plant for generating peak-shaving power using these devices. The major achievements in the FY1977 are summarized. The system analysis estimates annual power production possibly reaching 547,600 kWH. The heat-collecting test plant records a heat-collecting efficiency of 50 to 70% for collected heat quantity of 50 kW or more. The heliostat test confirms that the GL type is more favorable than the XY type. The heat absorber, which is a 1/3 model of the commercial device, is tested for its heat releasing performance, producing the quantitative released heat data. The heat transfer characteristics are investigated for the regenerative heat exchanger when the phase changes occur simultaneously on both molten salt and water sides. The mirror is exposure-tested in the field test for 1 year, to collect the data. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the testing/evaluation methods for high coherent lasers; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Ko coherent laser no shiken (hyoka hoho no hyojunka)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the development of high-precision, stabilized lasers, laser interferometers and signal processors, and developmental researches on the testing/evaluation methods for spectral characteristics of high-performance lasers, among others, for proposing the international standards. The program for narrowing the spectral lines for semiconductor lasers experimentally confirms validity of the external resonator structure with the diffraction lattice. The program for the developmental research on spectral width meter designs the width meter based on the delayed self-heterodyne technique, because of necessity for measurement of the spectral line width at a resolution of several hundreds Hz or less. The program for the saturation spectroscopy of iodine molecule designs and fabricates the iodine cell, to lock the semiconductor laser wavelength on the specific absorption line of iodine. It is judged, based on the test results, to be rational to adopt the absorption line of the (6-3) transitional P33 superfine structure. The program for the developmental research on wavelength meter conducts the preliminary tests for atmospheric pressure, temperature and humidity changes as the parameters which affect the measurement accuracy. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating plastic optical fiber; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies were made about methods for testing and evaluating plastic optical fiber (POF) for the purpose of submitting a proposition to IEC (International Electrotechnical Commission) for the methods to be internationally standardized. In this fiscal year, tests and analyses were conducted relative to the effects of the light source emission area size, wavelength, and axial displacement. Next, underfilled launch was studied from a practical viewpoint, and a method using a mode filter was proposed. Finally, round robin tests were conducted for each of the companies using overfilled launch and underfilled launch, and the reproducibility of measured values was grasped. In this fiscal year, a new study added, which involved a method for measuring structural parameters. Though POF was below standard as an object of IEC's gray scale method, yet it was found, thanks to the recently developed CCD (charge coupled device) cameras, that the method might also be applicable to POF. A groundwork plan was drafted on band test methods including the overfilled launch method toward international standardization. (NEDO)

Development of tire road noise chassis-dynamometer simulator. Effect of ISO surface replica model pad on tire road noise; Shisakushita tire romen soon shiken`yo jissha daijo simulator ni tsuite. ISO romen mogi pad wo sochakushita koka ni kansuru kisoteki kento

Energy Technology Data Exchange (ETDEWEB)

Tanaka, T; Murakami, T; Ogata, S; Sakamoto, I [Traffic Safety and Nuisance Research Inst., Tokyo (Japan)

1997-10-01

As a new test facility to clarify noise reduction method of tire road noise, Tire Road Noise Chassis-Dynamometer Simulator was developed. ISO surface replica pads made by copying the texture of ISO surface were attached on the roller surface of this system to simulate tire road noise. This paper described the specifications and characteristics of this system, and the effects of ISO surface replica pads on tire noise measurement by comparing the sound intensity in horizontal plane of tire noise measured in this system with that measured in a single drum tester with safety walk surface. 4 refs., 10 figs., 1 tab.

FY 1993 Research and development of ceramic gas turbines. Development of methods of testing and evaluating ceramic member bonding techniques; 1993 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-05-01

Studies are conducted to establish the methods of testing and evaluating applicability of ceramic-metal bonding for ceramic gas turbines, and the FY 1993 results are reported. The program involves measurement of residual stress by the X-ray method and durability tests for the joints of silicon nitride and austenitic stainless steel with copper as the intermediate layer, and analysis and classification of the strength/durability test results obtained until the previous fiscal year by the finite element method, to evaluate applicability of the joining. For the strength characteristics at high temperature, the test pieces tend to lose strength at 400 degrees C and higher, and high-temperature strength as cross-head displacement speed increases. The upper limit of bending strength at room temperature decreases as number of thermal cycles increases. The test pieces subjected to thermal cycles have a higher bending strength at high temperature than at room temperature. The results of the two-dimensional plasticity analysis of the residual stress in the joint by the finite element method are in good agreement with the results by the X-ray method. (NEDO)

Study on closed pressure vessel test. Effect of heat rate, sample weight and vessel size on pressure rise due to thermal decomposition; Mippeigata atsuryoku yoki shiken ni kansuru kenkyu. Atsuryoku hassei kyodo ni oyobosu kanetsusokudo, shiryoryo oyobi youki saizu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Aoki, Kenji.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering

1999-02-28

We have attempted to devise a new closed pressure vessel test apparatus in order to evaluate the violence of thermal decomposition of self-reactive materials and have examined some influencing factors, such as heat rate, sample weight, filling factor (sample weight/vessel size) and vessel size on Pmax (maximum pressure rise) and dP/dt (rate of pressure rise) due to their thermal decomposition. As a result, the following decreasing orders of Pmax and dP/dt were shown. Pmax: ADCA>BPZ>AIBN>TCP dP/dt: AIBN>BPZ>ADCA>TCP Moreover, Pmax was not almost influenced by heat rate, while dP/dt increased with an increase in heat rate in the case of BPZ. Pmax and dP/dt increased with an increase in sample weight and the degree of increase depended on the kinds of materials. In addition, it was shown that Pmax and dP/dt increased with an increase in vessel size at a constant filling factor. (author)

Fiscal 2000 achievement report. Development of coal gas production technology for fuel cells (Research using pilot test facility - for public release); 2000 nendo seika hokokusho (Kokai you). Nenryo denchi you sekitan gas seizo gijutsu kaihatsu - Pilot shiken setsubi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the development of a coal gasification furnace optimum for fuel cells, research and development was conducted of a coal gas production technology using the oxygen-blown coal gasification technology, and the fiscal 2000 results are put together. In the construction of the pilot test facility, part of the road in the site was constructed as continued from the preceding fiscal year. In the construction of the coal gasification facility, some of the devices were built, which were the coal feeding system, coal gasification furnace, heat recovery boiler, and the char recovery device, and some of the thus-built devices and procured devices were installed. In the study of the control of the operation of the oxygen-blown coal gasification system, the pilot test facility was divided into unit devices and, for each of the unit devices, detailed procedures for pre-start preparation, start, stop, and for the stop of accessorise were deliberated, and important operating steps were worked out. Timing charts were prepared for the operation of each of the facilities during plant start/stop operations. In the effort to deal with serious accidents, special operation procedures were studied and prepared on the case-by-case basis. (NEDO)

FY 1996 report on the results of the development of an entrained bed coal gasification power plant. Part 2. Investigational study of verification plant; 1995 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 2. Jissho plant ni kansuru chosa kenkyu hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

For the purpose of developing the technology of the integrated coal gasification combined cycle power generation, an investigational study of verification plant was made, and the FY 1996 results were summarized. In this fiscal year, the conceptual design was made of the Nakoso method based on the method of Nakoso pilot plant, the fixed bed method in which fixed bed gas refining facilities tested in Nakoso pilot plant were adopted, and the packed bed method. In the Nakoso method, 5 cases were studied using the air blown two-stage entrained bed for gasifier, dry two-stage fluidized bed for desulfurization and dry granular bed packed bed for dust removal. In the fixed bed method, 2 cases were studied using the air blown two-stage entrained bed for gasifier and dry fixed bed for gas refining. In the packed bed method, 2 cases were studied using the air blown two-stage entrained bed for gasifier and dry packed bed for gas refining. As to gas turbine facilities, 5 cases were studied in which GT output is 115MW - 215MW (output of combined cycle power generation: 220MW - 420MW). (NEDO)

Achievement report for fiscal 1999. Joint verification research on use for power generation of Omani superhigh-viscosity crude oil remaining unexploited; 1999 nendo Oman koku ni okeru miriyo chokonensei gen'yu no denryoku riyo ni kansuru kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A Mukhaizna oil field remains to be exploited in Oman, with an estimated reserve of 2.4-billion barrels of very heavy oil with an API (American Petroleum Institute) specific gravity of 15.3. The viscosity of the oil is so high as to be over 100-thousand cP (at 15 degrees C). The extremely high viscosity causes its exploitable rate to be so low as 3%, and makes shipment by pipeline quite difficult. In this survey, a method using water emulsion is proposed for viscosity reduction, which aims to reduce the Mukhaizna crude oil viscosity to 200mm2/s or less. In an experiment using the water emulsion method, oil is mixed with water at a rate of 72 to 28 in a shearing mixer for the production of a water emulsion of crude oil. It is found that a certain degree of stability is acquired using a surface active agent available on the market. Using this emulsion method, the crude oil is converted into a power generator fuel with a heating value of 6,775kcal/kg. The crude oil-turned product is a fine fuel superior to Orimulsion which is a fuel of the same type in terms of viscosity, amount of ash, and vanadium concentration. (NEDO)

Fiscal 2000 survey report. Survey for verification of new load levelling technique - IEA international joint project (Participation in IEA/DSM task); 2000 nendo fuka heijunka shuho jissho chosa hokokusho. IEA kokusai kyoryoku jigyo 'IEA/DSM task eno sanka ni tsuite'

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Japan participated in IEA/DSM (International Energy Agency/demand side management) Task X (performance contracting) for collecting information on energy service contracting business designed to promote load levelling centered DSM activities on the basis of market principles for achieving efficient operation of facilities. Task X aims to adjust and popularize the energy service contracting business. In the energy service contracting business, the facility related party and the energy service related party work under a contract to enhance efficiency of facility operation, and share the gains between them. In concrete terms, information was collected and exchanged at the 14th and 15th executive committee meeting of IEA/DSM Task X (Turkey in April 2000, Sweden in September 2000); new task preparation conference (Sweden in September 2000); 1st specialist conference (France in February 2001); and 17th annual convention of All-America ESCO (energy service company) Council (U.S. in November 2000). (NEDO)

Achievement report for fiscal 1998. Energy consumption efficiency improvement model business for developing nations (Demonstration research project on new cooling system in cement clinker production); Hatten tojokoku energy shohi koritsuka model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims at energy saving and CO2 emission reduction for a clinker cooling system (CCS), and a demonstration test was conducted at a demonstration cement plant in Indonesia. The plant started operation using the new CCS aiming for the enhancement of cooling and heat recovery efficiency. The actually achieved heat recovery efficiency attributable to the adoption of the new CCS was 60.8% against the target of 68%, this meaning an improvement of 8% over the value recorded prior to the new CCS adoption. As for increase in recovered heat due to heat recovery efficiency improvement of the CCS itself, it was 31kcal/kg-clinker. The heat reduction rate throughout the system thanks to the new CCS was 40kcal/kg-clinker. The kiln secondary air temperature increased for improved burner combustion performance for a rise of the clinker burning degree to 12kcal/kg in terms of calorie, and thus a reduction of 52kcal/kg-clinker in total was achieved. No mechanical trouble was reported with the new CCS. Investigations were conducted into cement supply/demand and technological trends in Indonesia, Vietnam, and China. Learnings from the investigation of German cement making technologies were fully utilized in the designing of the new system. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for evaluating thermal properties test on polymeric materials; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kobunshi zairyo no netsutokusei shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Targeting at proposing to ISO as an international standard, R and D has been performed on a method of the alternating current heating of the non-constant method, with regard to a method to evaluate the thermal properties test on polymeric materials in molten condition reflecting thin film polymeric materials, and the forming and processing technology. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed surveys on literatures related to thermal properties, development and commercialization of a measuring device, establishment of the measurement procedure, and putting some of the materials into database. The database was prepared mainly for heat diffusion rate and heat conductivity, wherein about 1000 items of information were collected. The temperature range of the measuring device revealed that stabilized data can be obtained from as low temperature as liquid nitrogen temperature to as high as 200 degrees C. The commercially available measuring device has no restrictions if the test sample thickness is from 1 mm to 100 mm, if the temperature range is from room temperature to 350 degrees C, if the temperature rising rate is from 0.01 to 5 K/min, and if the test sample form is film. Measurement at temperatures including those in the melting zone in the forming stage of each polymer has achieved as close result as having been called for in the initial objective. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of fine ceramics test and evaluation method for communication equipment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Tsushinkiki yo fain ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development is carried out aiming at the international standardization of methods for evaluating electric properties such as dielectric constant, dielectric loss, and surface resistance for fine ceramics for use in the high-frequency and ultrahigh-frequency bands. In this fiscal year, in the effort to establish an accurate measurement method for millimeter wave complex specific inductive capacity, the Fabry-Perot resonator was improved, and found to be capable of measuring 60-110 GHz. Efforts were made to improve on the accuracy of the cavity resonator excited by coaxial cable, for which various types of resonators were fabricated. For the calibration of evaluation apparatuses such as the Fabry-Perot resonator, cavity resonator excited by coaxial cable, and dielectric resonator excited by non-radiative waveguide, sapphire single crystals and PTFE (polytetrafluoroethylene) were selected as reference materials for measuring complex dielectric constant, and their dimensions and specifications were determined. In the study of the evaluation of basic surface properties, surface irregularity of the silver electrode was accurately measured by use of a thin-film surface geometry measurement apparatus, and the presence of a strong correlation between the jig silver electrode surface coarseness and the microwave band effective conductivity. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of methods to test/evaluate plastic optical fiber; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The experimental research was conducted with the aim of developing test/evaluation methods of plastic optical fiber (POF) and proposing a draft on the standards to IEC, and the FY 1999 results were outlined. In the study of the band measuring method, the equipment designed was compared/verified in the pulse method with the frequency sweep method equipment for quartz base optical fiber use to confirm the accordance. Effects were further studied of experimental conditions including exciting conditions. Also about the frequency sweep method, the same verification was made to see the accordance with POF measured values in the pulse method. In the analysis by theoretical calculation, obtained were the results by which the experimental results can almost be explained. In the experiment on the optical transmission, the bit-error-rate was measured by transmitting digital signals to POF. As a result, it was confirmed that there were close relations between the band width of POF, bit-error-rate and changes in receiving sensitivity. As to the above-mentioned band experimental method, strategy for standardization was studied, and the making of a draft on the standards was started which is to be proposed at the meeting of TC86/SC86/WG1. (NEDO)

Achievement report for fiscal 1990. Research and development of ceramic gas turbine (Development of test and evaluation methods for ceramic member bonding technology); 1990 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Development of test and evaluation methods has been performed on a technology to bond ceramics with metals from the viewpoint that what governs bonding is residual stress. Activities were made in the following three fields: 1) tests and researches, 2) analytical studies, and 3) studies on correlation of residual stress with strength characteristics. In Item 1, selections were made on Si{sub 3}N{sub 4} as the ceramics, ordinary steel as the metal, and the brazing process in vacuum using Ti-based active metal as the bonding method. Discussions were given on processing of test pieces and the procedure thereof, an X-ray stress measuring method, a non-destructive inspection method, and a strength testing method. In Item 2, discussions were given on analysis of the bonding method and the residual stress in the bonding material due to brazing of ceramics with metal, for example, and the effects of the cutting process on the residual stress. In Item 3, discussions were given on mechanical strength evaluation on the bonding materials including the processing defects, for example, with regard to the correlation of the bonding residual stress with the mechanical strength characteristics, and on the effects of the residual stress on the tensile strength. (NEDO)

Achievement report for fiscal 1989. Research and development of ceramic gas turbine (Development of test and evaluation methods for ceramic member bonding technology); 1989 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-05-01

Development of test and evaluation methods has been performed on a technology to bond ceramics with metals as a support to develop a ceramic gas turbine (CGT), from the viewpoint that what governs bonding is residual stress. Activities were made in the following three fields: 1) investigative studies, 2) tests and researches, and 3) analytical studies. In Item 1, literatures were investigated, and research plans were established with regard to residual stress. Selections were made on Si3N4 as the ceramics, ordinary steel (S45C) as the metal, butt joint bonding of flat plates with each other as the bonding method, X-ray stress measuring method and IF method (semi-destructive test) as the residual stress measuring methods, and the finite element method as the analytical method. In Item 2, bonded test pieces were made, and the residual stress measuring test was performed to discuss the test and evaluation methods in relation with the bonding patterns and adaptability of the bonding. In Item 3, basic discussions were given on applicability of the residual stress analysis method using the finite element method, and on analysis of the affecting factors and modeling. (NEDO)

Achievement report for fiscal 1991. Research and development of ceramic gas turbine (Development of test and evaluation method for ceramic member bonding technology); 1991 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-05-01

Development has been made on the test and evaluation method for a technology of bonding ceramics with metals from a viewpoint that what governs the bonding is residual stress. Activities were made on 1) test researches, 2) analysis researches, and 3) researches on the correlation of residual stress with mechanical strength characteristics. In Item 1, tests on the bonding residual stress and mechanical strength characteristics, tests on high temperature mechanical strength characteristics, X-ray stress measurement, IF method measurement, and mechanical strength test were performed. In Item 2), researches were made on three-dimensional stress analysis of interface bonded with different materials, high temperature mechanical strength of bonded bodies, and heat cycle fatigue strength. In Item 3, destruction dynamic discussions were given on the effects of the residual stress on the tension rupture strength, and cracks on bonded interface. Specifically speaking, residual stress in four kinds of bonded bodies with various sizes (Si{sub 3}N{sub 4}/Cu/steel), for example, was measured, the bonded bodies were subjected to a cutting process, and considerations were given on the effects imposed on re-distribution of the residual stress due to the cutting and on the bonding strength. (NEDO)

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

Achievement report for fiscal 1993 on developing entrained bed coal gasification power plant. Part 2. Summary of tests and researches on pilot plant operation; 1993 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 2. Pilot plant unten shiken kenkyu no gaiyo hen

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-01

Tests and researches have been carried out on operation of a 200-t/d entrained bed coal gasification pilot plant built with an objective of establishing the coal gasification composite power generation technology. This paper summarizes the achievements in fiscal 1993. The current fiscal year has performed the test operation on the pilot plant as a whole by using the coal D in continuation from the previous fiscal year. For the gasification furnace facilities, an air variation test was conducted for charging coal into the gasification furnace by using recovered oxygen, wherein satisfactory control was verified on oxygen concentration in the air supplied into the gasification furnace. In the gas refining facilities (dry desulfurizing facilities), the total sulfur concentration at 300 to 650 ppm in the gas produced from the coal gasification furnace was refined to 30 to 100 ppm, having achieved the initial target value. The gas refining facilities (dry dust collecting facilities) have achieved satisfactory result that the entrance dust concentration at 66 to 270 mg/Nm{sup 3} was reduced to the exit dust concentration at 1 to 3 mg/Nm{sup 3}. With respect to the gas turbine facilities, the planned values of output and thermal efficiency were satisfied, having derived good performance characteristics. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a testing/evaluation method of biological use fine ceramics; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seitaiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of standardizing/international standardizing an evaluation method of the characteristics required for biological use fine ceramics, and the FY 1999 results were summed up. In the study of characteristics of biological use fine ceramic materials, it was confirmed that zirconia ceramics are more excellent than alumina ceramics in static strength, repeated loads and fatigue properties in the atmospheric air at room temperature. In the study of the evaluation method of biological affinity, the standardization of the simulated body liquid preparation process was studied, and the simulated body liquid was prepared. To evaluate the bioactivity of biological use fine ceramics without making animal experiments, the simulated body liquid in which the ion concentration was made exactly equal to that of human being was prepared using 2-hydroxyethyl-1-piperazinyl ethane sulfonic acid as buffer. There were seen no changes in ion concentration for four weeks at longest as long as this liquid is kept in airtight container at temperature of 36.5 degrees C or below. The present situation of the standardization of bioceramics was surveyed. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standards development of chemical analysis and non-destructive inspection methods for pure titanium metals; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Junchitan no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To propose it to ISOTC79 and ISOTC135, study was conducted for standardization of chemical analysis method and non-destructive inspection method for industrial use pure titanium. As the chemical analysis method, the inductively coupled plasma atomic emission spectrometry which has good detection limit was developed, and at the same time, the standardization of spark and/or glow discharged atomic emission spectrometry was developed. As the non-destructive inspection method, developmental study on the following was carried out: surface defect inspection method of pure titanium metals by laser scanning inspection system or CCD camera; internal defect inspection of pure titanium sheet and coil by plate wave ultrasonic inspection method; internal defect inspection of pure titanium bar by eddy current method; inspection of very small leakage of pressurized fluid through defects in pure titanium pipe and tube by pressure differential testing method. As a result of the study, standards of system performance and tolerance were determined in analysis of Pd, Si, Al, Cu, Mo, Zr, Nb, Ta and Y. Further, analytical conditions and application ranges of the spark discharged atomic emission spectrometry were made definite in terms of 19 elements including Mn, Fe, Ni, Cr, Sn, Pb, Si, Al, V, Cu, Mo, Zr, Nb, Ta, Co, B, Y, C and W. (NEDO)

FY 1992 report on the results of the development of an entrained bed coal gasification power plant. Part 3. Operation test of pilot plant (2/2); 1992 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken hen (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-02-01

The study of operation test was made of the 200 t/d entrained bed coal gasification pilot plant that was constructed with the aim of establishing technology of the integrated coal gasification combined cycle power generation, and the details of the FY 1992 results were summarized. As to the test of gas turbine facilities, at RUN 10, the scheduled test on coal gas mixed combustion continuous operation/coal gas fired operation was not carried out because of the worsening of the state of gasifier operation. The operation was just made for a short time. At RUN 11, it was confirmed that the motion of equipment in the bleeding system was good at the time of the bleeding cooperation test and there was no anomaly also in the state of gas turbine operation. At RUN 12, it was confirmed that the motion of load/pressure control functions was normal in the state of GT load of about 5MW. At RUN 13, it was confirmed that the control function of GT governor was confirmed in the total pressure control test. As a result of the operation test of these, items of improvement were extracted for actual pressure/actual size combustor facilities, safety environment facilities and electric/control facilities. The measures taken for each item were studied. (NEDO)

FY 1992 report on the results of the development of an entrained bed coal gasification power plant. Part 3. Operation test of pilot plant (1/2); 1992 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken hen (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-02-01

The study of operation test was made of the 200 t/d entrained bed coal gasification pilot plant that was constructed with the aim of establishing technology of the integrated coal gasification combined cycle power generation, and the details of the FY 1992 results were summarized. At RUN 10, conducted were the confirmation of the quantity of state of gasifier in the coal-fired high load operation and coal-fired constant load operation, and slagging survey. At RUN 11, the evaluation made after the work for prevention of slagging, and confirmation of the quantity of state of gasifier at a load of 80% heat input. At RUN 12, the evaluation of the measures taken against slagging, and test on the high load stable operation. At RUN 13, the evaluation of the measures taken against slagging, and large combustor response/total pressure control response tests. At RUN D1, test on the change of coal kind from A coal to D coal, and test on the initial adjusting operation of D coal. In the trial operation of these, the following were generated and the preventive measures were studied: impossibility of circulation of desulfurizing agent in gas refining facilities (dry desulfurizing system), bolt fracture of gas refining facilities (separator of dedusting facilities). (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of test/evaluation methods of telecommunication use fine ceramics; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Tsushin kikiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to high frequency/ultra-high frequency band use fine ceramics, the R and D were conducted with the aim of establishing the evaluation method of electric characteristics such as dielectric constants and dielectric losses, and at standardizing and internationally standardizing the principle of the measuring method, preparation method of equipment and test pieces, measuring procedures, etc. The FY 1999 results were summed up. As to the measuring method of electric characteristics, enhancement of measuring accuracy was made for the millimeter wave coaxial exciting cavity resonator method and the Fabry Perot method. Further, field survey was made of the developmental trend of the measuring method in Europe and the U.S. Concerning measuring use standard test pieces, candidate materials were trially manufactured, and the shape/dimension of a part of the candidate materials were determined. As to surface basic properties, effects of surface shape and convex/concave faces of test pieces on characteristic evaluation were studied, and it was made clear that convex/concave faces were greatly influential. In the technical committee, how to proceed with the development was discussed in the first meeting, and evaluation methods and candidate standard substances were selected in the second meeting. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation testing method of thermal properties of polymer materials; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kobunshi zairyo no netsutokusei hyoka shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of proposing it to ISO, the R and D were conducted of a new evaluation method of thermal properties of polymer materials. The FY 1999 results were summarized. In this fiscal year, the development of the ac Joule heating equipment was proceeded with based on the study at the technical committee, and the measuring device was installed. In the comparative measurement with conventional methods, study was proceeded with of the laser flash method, AC calorimetry method and specific heat measurement. In the technical survey, the developmental state of the ac method, especially, was examined as a testing method of thermal properties of polymer materials. It is in the stage of the basic research by keyword selection, and the search for literature is to be made in full scale. As to the needs in the industrial circle, as a result of the questionnaire survey made, it was found out that there were a wide variety of the needs for general-purpose/functional film materials, forming materials, composite materials, coating, adhesives, cohesive materials, etc. Further, as the application field, construction materials, agriculture, food, packaging, etc. were cited in addition to the magnetic recording in electric/electronic relations, sensor insulation, OA equipment, wiring board, etc. (NEDO)

FY1998 survey on IEA international cooperation project on demonstration and survey of new load leveling methods (participation in the IEA/DSM task VI); 1998 nendo fuka heijunka shinshuho jissho chosa IEA kokusai kyoryoku jigyo 'IEA/DSM task 6 eno sanka ni tsuite' chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It is intended to participate in the IEA international cooperation project related to DSA, exchange items of information, and promote demonstration and survey of new load leveling methods. The existing and newly proposed DSM mechanisms as the achievement of the previous tasks were put into order. The arena of information exchange and discussions was prepared through use of the Internet homepage for the IEA/DSM implementation agreement. Necessary official policies were also made available. Points of precautions when the mechanisms of other countries are used in Japan: the key to the success depends on social or cultural situations that work as the base; therefore, comparisons and analyses are necessary on such elements as customers as the object, energy projects and governments; compatibility of the situation and pattern of the demand side with the DSM technologies governs the reasonability thereof; the types of the mechanisms are narrowed down by size of the customer division, consumption pattern, electric power quality and safety, and needs on the flexibility; proliferation levels of the DSM technologies determine the appropriate mechanisms; and how the DSM is conceived against the final consumption is governed by the conception by both of the customers and the government. (NEDO)

FY 1997 report on the verification survey of new mechanisms for load leveling. IEA`s international collaboration `Participation of Japan in IEA/DSM Task VI`; 1997 nendo chosa hokokusho (fuka heijunka shinshuho jissho chosa). IEA kokusai kyoryoku jigyo `IEA/DSM task IV eno sanka ni tsuite`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Current electricity markets in Europe and the USA are drastically changing due to the introduction of competition principle and the reconsideration of business systems. Are also changing the activities and their forms of DSM (demand side management) for load leveling which has been conventionally conducted by electricity companies for the efficient operation of facilities. Task IV and Task VI aim at developing new mechanisms to promote DSM in the changing electricity markets as well as disseminating and communicating information on the new mechanism. Japan participates in Sub-task IV/6 and 7 and Task VI. Activities for developing new mechanisms are divided into Phase 1 and Phase 2. The Phase 1 includes review of existing mechanisms and preliminary development and evaluation of new mechanisms. The Phase 2 includes the detailed development of new mechanisms and evaluation criteria, communication and information about mechanisms, and identification of the public policy implications which would follow a decision by the responsible authorities to implement each of various DSM mechanisms. The time frame of Phase 1 is between February 1996 and March 1997, and that of Phase 2 is between January 1997 and December 1999. 2 figs., 4 tabs.

R and D of suitable unit to heightening in grade of mobile wireless telegraphy system; Test on data transmission characteristics and research on transmission method. Ido musen system no kodoka ni tekigo kano na sochi no kaihatsu kenkyu; Deta denso tokusei shiken oyobi denso hoho no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Onigawara, Shuichi; Koyama, Masayoshi; Masunaga, Katsutoshi [Kyushu Electric Power Co., Inc., Fukuoka (Japan)

1989-03-30

In order to heighten the grade by the present mobile wireless telegraphy system, through the experimentation and research on both data transmission and error correction methods, both data and facsimile transmission were confirmed to be possible together with the following result: In the character transmission by a CPU connection and other encoded transmissions in which even an error by one bit considerably influences the contents of data, 1200bps, as able to be widened in service area, is profitable. While the data transmission in the mobile wireless telegraphy generates many errors due to phasing and noise along the propagation route. To attenuate those errors, error correction encoding is effectively applied with a correction method to be selected by kind of data. Further the 150MHz band, as more largely influenced by urban noise than the 400MHz band, narrows service area in the urban district. While the mobile wireless telegraphy is restricted in frequency band region. 12 refs., 26 figs., 9 tabs.

FY 2000 Development of international standard supporting new industries. Standardization of the test method for performance evaluation for polymer products under critical environment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kakoku kankyoka ni okeru kobunshi seihin no seino hyoka shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project is aimed at development of the testing methods which can adequately predict resistance of polymer products to weather in various areas of largely different environmental conditions. Described herein are the FY 2000 results of the outdoor exposure tests, and the tests in which the samples are exposed to light from a laboratory source and to a solar light-concentrating test unit. The FY 2000 project include the exposure of the samples directly to the outdoor conditions and glass-filtered light, which are continued from the previous year; solar light-concentrating type exposure tests conducted in Arizona, USA, started in this year; and reproduction tests for the exposure to a xenon lamp light, review of short exposure time areas and spectral degradation tests, among others. The program for evaluating the reference materials includes measurement of cumulative property changes of 4 types of plastic and 10 types of rubber materials by the exposure tests. The tests of resistance of plastics to weather have been exposing the samples, stabilized and not stabilized, for 16 months. For the reference candidate samples, the data of exposure for 1 month are collected 16 times. The tests of resistance of the rubber materials to weather reveal that each sample is deteriorated by hardening and deterioration proceeds with time. (NEDO)

Report on the achievements in the Sunshine Project. A comprehensive report on development of coal liquefaction technologies and a performance test on Chinese coal liquefaction (fiscals 1981 through 1987); Sekitan ekika gijutsu kaihatsu seika hokokusho. Chugokutan ekika seino shiken sogo hokokusho (1981 nendo kara 1987 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The present Japan-China joint development project is intended to study liquefaction performance of different types of Chinese coals, select coal types suitable for coal liquefaction, and serve for enhancement in the coal liquefaction technologies employed by the Chinese side. Since a small continuous testing device has been installed in fiscal 1982 and begun with the trial operation in March 1983, the liquefaction test has been performed for about five years, and is scheduled to continue another three years. Chinese coals produced in seven provinces and two autonomous regions have been subjected to the coal type selection, on which discussions were given for liquefying reaction characteristics by using autoclave testing and small continuous testing devices. As a result, circulation tests were performed by the end of fiscal 1987 on five coal types, namely Beisu coal, Texgxian coal, Xianfeng coal, Shenmu coal, and Meihekou coal. Data were acquired during the circulation and at the equilibrium. Comparison of the results of tests on these five coal types with the results having been acquired from the 0.1-t/d BSU in Japan before modification verified the result being nearly reasonable. (NEDO)

Fiscal 1999 technical achievement report. Research and development project on prompt-effect international standards creation (Standardization of test and evaluation of superhigh-precision toothed gear); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Choseimitsu haguruma no seidono shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In ISO1328 that covers specifications on precision of toothed gears, gears are graded according to the magnitude of error, but there is no system established for guaranteeing measured error values for accuracy. Activities are conducted for realizing such a guarantee, for establishing methods for testing and evaluating gear precision measuring devices, and for working out international standards for them. It is decided that the current status be investigated and then a concrete method be proposed as an international standard centering about gear precision measuring digital devices which will stay important in the future. A digital measuring device enhanced in precision is constructed by way of trial, and then it is proved that the newly fabricated device works effectively in the calibration of gear precision measuring devices in general use. Thanks to this process, basic data are collected about the measurement of gear precision using a gear precision measuring digital device, and this enables the preparation of a draft of criteria for international standardization. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Demonstrative study on photovoltaic power generation system (Research on high-density linking technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Taking a photovoltaic power generation system linked to distribution lines at high density as the object of discussion, investigative studies were performed on electric power quality, clarification of various problems including effects on operation and protection of distribution lines, the corrective measures thereof, and enhancement of power quality by utilizing inverters. This paper summarizes the achievements in fiscal 1999. In clarifying the problems associated with high-density linkage, discussions were given on possible amount of PV introduction into the distribution lines as seen from the electric performance aspect including power quality and safety. Placing the importance on identifying the current status of single operation preventing technologies, demonstrative discussions were given on the single operation preventing performance of commercially available inverters in testing 84 inverters operated in parallel by using the Rokko testing installation. In discussing the corrective measure technologies, development has been performed on a decentralized voltage stabilizing device based on injection of reactive power into high-voltage distribution lines as a measure to suppress voltage rise in the distribution lines. The reasonability of the fundamental characteristics thereof was verified by using the Akagi testing facilities. In addition, improved design was progressed on the two-step active prevention system. Commencement has taken place on verification of the reasonability of the fundamental characteristics and tests on parallel operation of multiple number of units. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

Report on the surveys in fiscal 1999 on the demonstrative investigation of a new load leveling method. Participation to the IEA/DSM task VI, an IEA international cooperation project; 1999 nendo fuka heijunka shinshuho jissho chosa hokokusho. IEA kokusai kyoryoku jigyo IEA/DSM task VI eno sanka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Participation was implemented to the IEA/DSM task VI as the demonstrative investigation of a new load leveling method. The DSM strategy is a means to achieve the public objectives of wide range, wherein the DSM mechanism is important, that can obtain accurate and useful information in competitive markets. Consumer protecting activities have close relation with general information needs. A financial incentive mechanism is also necessary to support nurturing of business organizations and new ESCO industries. A market forming mechanism using the DSM can solve the problem of disagreement in the incentives (for example, private profit of electric power companies and the public nature of the government). These include system plans considering the DSM, setting of upper limit in the profit, demand side bidding, and green charge institution. It is important to utilize affluent findings and means used in the past and utilize each mechanism to meet the needs for public benefit at the present and in the future, while structuring an electric power business structure incorporating the DSM. The DSM promoting mechanisms in each country were classified and put into order of regulations, supports, funds, and markets. (NEDO)

FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 3. Adjustment of the operation test of pilot plant (2/2); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken chosei hen (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-01-01

The adjustment was made of the operation test of the 200 t/d entrained bed coal gasification pilot plant that was constructed with the aim of establishing technology of the integrated coal gasification combined cycle power generation, and the results were reported. As to the adjustment of the operation test of gas turbine facilities, the following were conducted: tests 1 and 2 on light-oil firing characteristics, test on coal gas ignition, tests on fuel change/gas firing, test on fuel change. And, 12 cases of troubles, the causes and measures against them were reported. Relating to the adjustment of the operation test of actual pressure/actual size combustor testing facilities, tests on hot air device/air heating device and tests 1-3 on light-oil firing were carried out, and 7 cases of troubles, the causes and measures against them were reported. Concerning the adjustment of the operation test of safety environment facilities, tests were made of RUN 3-6, RUN 7 (1 and 2), RUN 8 (1-4) and RUN 9 (1-3), and 20 cases of troubles, the causes and measures against them were reported. As to the adjustment of the operation test of electric/control facilities, items of improvement were reported of gasifier facilities, gas refining facilities, gas turbine facilities, actual pressure/actual size combustor testing facilities, safety environment facilities and total control facilities. (NEDO)

Report on survey in fiscal 1999 for promotion of geothermal development. Supplementary survey on data processing (fluid inclusion test) for Tsujinodake Area No. B-6; 1998 nendo chinetsu kaihatsu sokushin chosa hokokusho. Data shori ni kakawaru hosoku chosa (ryutai gan'yubutsu shiken nado) No.B-6 Tsujinodake chiiki

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

This paper reports the fluid inclusion test in the Tsujinodake area in fiscal 1998 for the survey on promotion of geothermal development. The fluid inclusions were classified into three types: those with the maximum value or the average value of the homogenizing temperature agreeing nearly with the saturated boiling curve, those with the homogenizing temperature showing the interim temperature between the present well temperature and the saturated boiling curve, and those agreeing nearly with the present well temperature. It is presumed that the bed temperatures in depths of 1,125.30 m and 1,427.50 m have changed very little since after formation of the present circulating and flowing systems of geothermal waters until now. In contrast at the depth of 1,691.75 m, the bed temperature was estimated to have fallen slightly from that in the most active period of the geothermal water activities. As a result of the rock age measurement, it is estimated that, in the Nansatsu bed groups distributing around the N10-TD-1 well, the temperature has fallen gradually after having been subjected to hot water alteration actions at higher than 200 degrees C, and cooling has taken place down to 200 to 250 degrees C as the fission track date temperature of zircon in the relatively late period (about several hundred thousand years before). There should have been no thermal change that affects the age measurement up to now since then. (NEDO)

FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 3. Adjustment of the operation test of pilot plant (1/2); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu - Sono 3. Pilot plant unten shiken chosei hen (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-01-01

The adjustment was made of the operation test of the 200 t/d entrained bed coal gasification pilot plant that was constructed with the aim of establishing technology of the integrated coal gasification combined cycle power generation, and the results were reported. As to the adjustment of the operation test of gasifier facilities, the light-oil firing test and tests of RUN 1-9 were conducted, and the paper reported cases of 49-item troubles, the causes, measures against them, improvement of facilities, etc. For slagging, operation conditions, improvement of various facilities, etc. were studied. Relating to the adjustment of the operation test of gas refining facilities (dry desulfurization facilities), the following were carried out: test on empty column gas circulation, test on desulfurizer circulation characteristics, test on SO2 reduction tower, test on warming-up characteristics, tests 1-3 on initial performance, tests on change in gas turbine fuel and loads. And, 21 cases of troubles, the causes and measures against them were reported. Concerning the adjustment of the operation test of gas refining facilities (dry dedusting facilities), the following were conducted: test on non-load sequence, test on confirmation prior to letting gas through, tests 1-3 on initial performance, test on dedusting characteristics. And, 22 cases of troubles, the causes and measures against them were reported. (NEDO)

FY 2000 report on the results of the development of the stand-by consumption power reduction technology. Verification experiment on the technology to reduce stand-by power of household electric appliances; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden seihin taikiji denryoku sakugen gijutsu no jissho jikken

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Study was made of the energy conservation by reducing stand-by consumption power of household electric appliances. In the study, remote control, household electric appliance, and outlet box were developed, and a system was developed in which each of the three was connected by network and the commercial power source supply is cut off at the time of the stand-by state of household electric appliances. The outlet box collectively manages timer information and reservation information. User sends out control command toward the outlet box using the two-way remote control, and controls all the household electric appliances connected via network. The screen data of household electric appliances are sent to the two-way remote control via the outlet box and presented to user. When the time comes for automatic execution such as video recording during absence, the outlet box carries commercial power source to household electric appliances. Using these appliances, verification experiment was carried out in the model house which was built with the ordinary house as model. A reduction in stand-by consumption power, approximately 218kWh/year(center dot)household, was verified. (NEDO)

Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

Fiscal 2000 research and development of technologies for intelligent infrastructure creation and utilization. Development of high-precision screening assay system for endocrine disrupting chemicals and construction of database; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu. Naibunpi kakuran busshitsu no koseido screening shiken hoho no kaihatsu oyobi data kiban seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is carried out for the establishment of a system for assaying endocrine disruption now presenting itself as a hazard and for the application of the assay system to important chemicals and chemicals under development for the detection of presence of endocrine disrupting action in them. In this fiscal year, for the establishment of a reporter-gene assay system, cell characteristics were clarified through the determination of the expression sequence of the produced cell, the determination of the stable conservation period of the cell, and the study of the sustenance of activity. Studies were conducted, targeted at the stable supply of cells usable for high-throughput screening. Basic data were collected for the Hershberger assay being developed by OECD (Organization for Economic Cooperation and Development) and for the repeated administration test method for assaying thyroid hormone action by use of pubertal rats. For the assay of impact on environmental organisms, moreover, basic data were collected for the establishment of testing methods using fishes and amphibians. (NEDO)

FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Standardization of the testing/evaluation methods for displays for information processing devices; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Joho shori kikiyo display no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the tests and studies for the methods of testing and evaluating the transparent electroconductive films necessary for production and product evaluation of liquid crystal displays, for their international standardization. The studies are directed to the testing/evaluation methods for internal stresses and adhesion force, surface shapes, and microstructures, and also to surveys on the market/technology trends, and preparation of the international standard drafts, among others. These result in, e.g., development of the quantitative evaluation technologies for internal stresses by the micro-sheet glass method, and surface shapes by atomic force microscopy. The local grain size and orientation are elucidated by transmission electron microscopy, to obtain new knowledge of the microstructures. Various technologies related to adhesion testing/evaluation methods are proposed for ISO/TC206, but it is found none is applicable to transparent electroconductive films. The standard drafts are prepared for standardization of the testing/evaluation methods for internal stresses, adhesion force and surface shapes. (NEDO)

FY 1998 results of the intellectual basement project using functions of private companies (venture promotion type basement creation R and D project). Development of endocrine disrupter testing method and development of environmental assessment method; 1998 nendo naibunpi kakuran busshitsu ni taisuru shiken hoho kaihatsu oyobi eikyo hyoka shuho kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of assessing the risk in relation to endocrine disrupting chemicals, the following were conducted: development of testing/assessment method for endocrine disrupting chemicals, survey of the actual exposure assessment, development of measuring method for the concentration in the environment. In the development of the testing method, the following were carried out: development of a high-throughput screening method for evaluating endocrine disrupting chemicals; as screening testing method using mammals, uterotrophic assay, Hershberger assay using castrated male rats, thyroid hormone assay in pubertal rats, enhanced OECD 407 test guideline for 28-day toxicity test; study on yeast two-hybrid assay for endocrine disrupter; sex-reversal assay for suspected endocrine disrupting chemicals using S-rR strain medaka. In the development of exposure assessment method, estrogenic potency of individual nonylphenol congeners isolated from technical mixtures; determination of endocrine disrupters and related chemicals from industry and nature origin in river water and sediment; research for the flow of industrial origin chemicals; reconstruction of pollution history of chemicals using sediment cores. (NEDO)

FY 2000 report on the results of the infrastructure construction project for spreading high-efficiency fuel cell systems/development of test apparatuses for evaluation of fuel cell systems for automobiles; 2000 nendo kokoritsu nenryo denchi system kiban gijutsu kaihatsu / jidoshayo nenryo denchi system hyoka shiken sochi no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project studies the testing/evaluation methods for spreading fuel cells for automobiles. Described herein are the FY 2000 results. The problems involved in evaluation of the single cell units are classified into those involved in the cell construction and methods of evaluating the operation performances of the single cell units. These problems are analyzed mainly by literature survey. The mode simulation tests will be greatly simplified, if the system can be tested on the bench without being actually boarded on the vehicle. Therefore, this project is aimed at development of a comprehensive mode simulator which can be automatically operated corresponding to the running modes of various countries, to test the performance of FCEV and to examine the effects of each component independently on the vehicle performance. The factors required to reproduce the actual driving states of an FCEV on the bench are analyzed, and the conceptual designs are drawn for the controlling algorithms. It is necessary to standardize the stack and reformer testing methods, in order to evaluate the fuel cell system components. For these objects, the prototype units are constructed to evaluate 10kW direct hydrogen type stacks and 5kW methanol reformers. The units are also constructed to evaluate the high-pressure (1MPa) reformer reactors and hydrogen separation membrane systems. (NEDO)

Fiscal 1999 research result report on energy and environment technology demonstration research support project (International joint demonstration research project). Japan- Russia joint demonstration research on large-capacity long- distant DC power transmission technology; 1999 nendo daiyoryo denryoku no chokyori chokuryu soden gijutsu ni kansuru Russia kenkyu kikan tono kyodo jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Under the assumption of a large-capacity DC power transmission model project in the Far East and Siberia districts, technical study was made on the basic design of the project, considering selection of concrete power generation and consumption sites and power transmission routes, power transmission/transformation equipment, cables, and environmental impact. Study was also made on its applicability to similar projects in Japan. The model project aims at integration of Eastern Integrated Power System in the Far East and Russian Unified Power System, and development of abundant undeveloped hydraulic and tidal power generation in the Far East. The study result showed that (1) construction of the high-voltage DC power transmission (HVDC) system of model project class voltage and capacity in Eastern Siberia is possible technically enough, (2) the total construction cost of the model project scheduled to be put into operation in 2025 amounts to nearly $4.7 billion, and (3) the model project is environment-friendly without any CO{sub 2} gas emission because of hydraulic and tidal power generation. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. Demonstrative study of the photovoltaic power system (Study of the high density connection technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu - Taiyoko hatsuden system no jissho kenkyu (Komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the photovoltaic power system connected to the distribution line in high density, study was made in terms of the power quality, elucidation of the effect on operation/protection of the distribution line and the measures to be taken, improvement of power quality using inverter, etc., and the FY 2000 results were summed up. In this fiscal year, the results of the research made in four years were arranged, and at the same time, the theoretical analysis, verification test, etc. that were necessary for summarization of the research results were carried out. As to various kinds of technology for the measures to be taken, the following were conducted: study of the effect on the rise in voltage of the distribution line, development of the dispersed control type voltage stabilization method, test on characteristics of individual operation of the inverter on the market, simulation analysis of characteristics of the continuous individual operation, development of the high reliability individual operation prevention method, verification study of the environmental adaptability, etc. As a technology for improving utility value of the photovoltaic power generation, a high function inverter was developed which conducts not only the dc-ac conversion, but the smoothing of generating output/load variations and load higher harmonics/reactive power compensation. At the Rokko testing facilities, test was made of the parallel operation (5 units) of the pole transformer. (NEDO)

Report on 1980 result of R and D under Sunshine Project. Development of solvent extraction liquefaction technology and demonstrative investigation on development of brown coal liquefaction technology (studies on high-temperature in-oil pulverization); 1980 nendo yozai chushutsu ekika gijutsu no kaihatsu / kattan ekika gijutsu kaihatsu jissho chosa seika hokokusho. Koon'yuchu funsai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This paper explains the results of development of coal liquefaction technology under the Sunshine Project in fiscal 1980. As a part of the development of brown coal liquefaction technology, pulverization of the first-dehydration brown coal was technologically established, as were adjustment of slurry and equipment for the second-dehydration process. A 20kg/h high temperature in-oil pulverizer was designed, constructed and made ready for the studies. A high temperature mill was a wet type ball mill, 500mm{phi}(diameter) x 1,500 mm length and 2.2kw. Coal was fully pulverized even in a solvent such as creosote oil and anthracene oil freed from crystal, and was adjustable to a prescribed particle size distribution. The wet type slurry adjustment method offered prospects that solvent/coal slurry moisture could be controlled to a prescribed value. An analysis was made on the mill outlet gas and drain collection liquid at the time of high temperature in-oil pulverization, which provided knowledge of securing safety. An analysis was also made on the influence of the heating temperature rise of the mill on the strength, which provided basic data for examining the strength of the mill. Using brown coal as the raw material, slurry was prepared, which confirmed that the device had functions as planned. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. Development of a test method of halogen-free flame-retardant cables and a study of the cable standards; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Non halogen nannen cable no shiken hoho kaihatsu narabini cable kikaku no kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As for halogen-free flame-retardant cables with high recyclability and safety (HFFR cables), the development is being promoted in many countries as a next generation cable. The standard of HFFR cables has been set up by some countries and groups in the U.S. and Europe, but the international standard has not yet been established independently. The purpose of this R and D is the development of a test method to appropriately evaluate the performance of HFFR cables and its standardization, and the proposal of the international standardization on common items of the cable standard. A study group was sent to the U.S. and Europe to investigate the development, application status and test methods of the HFFR cable overseas. The ion chromatography and FT-IR method were studied as methods to evaluate corrosivity/toxicity of the gases emitted in combustion. The performance of HFFR cables in Japan and abroad was also evaluated mainly by IEC standards. Further, considering the results of the overseas surveys, the structure and details of the international standard plan on HFFR cables were studied, and approaches to the international standardization were studied. 32 refs., 31 figs., 54 tabs.

Report on 1977 result of Sunshine Project. Test research for detailed design of coal gasification plant (pressure fluidized gasification method for mixed material of coal/heavy oil); 1977 nendo sekitan gas ka plant no shosai sekkei no tame no shiken kenkyu seika hokokusho. Sekitan jushitsuyu kongo genryo no kaatsu ryudo gas ka hoshiki

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

Since fiscal 1974, development has been implemented for the coal/heavy oil hybrid gasification process which converts coal and heavy oil simultaneously to clean fuel gas. With the purpose of obtaining basic data to be reflected on the detailed design of 7,000 Nm{sup 3}/d pilot plant of the subject process started in fiscal 1977, implemented this year were (1) test on high pressure valves and (2) research on operation studies. In (1), a life test device for high pressure operation valves will be designed and manufactured so that basic materials may be obtained for the development of durable operation valves to be used in a high temperature and high pressure coal/heavy oil slurry feeding device. Operation studies of a low pressure slurry feeding device will be continued, accumulating data required for the design of the coal/heavy oil slurry feeding device. In (2), studies will be started on the operation of a 300{phi}(diameter) internal heat type low pressure gasification device, collecting know-how for the model and design of the gasification furnace of the pilot plant. Gasification experiments will be continued using the high pressure gasification device, so that gasification characteristics under a high pressure will be grasped to examine the optimization of gasification conditions. In addition, a fluidized bed quencher test equipment will be designed and manufactured. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a testing/evaluation method of the performance of polymer products under the severe environment; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kakoku kankyoka ni okeru kobunshi seihin no seino hyoka shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted with the aim of standardizing a testing method for appropriately predicting weatherability of polymer products also in areas where environmental conditions are largely different and of proposing it to ISO. The FY 1999 results were outlined. In this fiscal year, methods to test weatherability of polymer products abroad and in Japan were surveyed mostly on JIS and ASTM, and the state of tackle with the making of standards in each country was also surveyed. In the tests on plastics and rubber, the following were conducted: selection/fabrication of test pieces, 3-year outdoor exposure tests in three places in Japan where environmental conditions are different, in the U.S. and in Indonesia, artificial light source exposure tests for about 200-1000 hours using xenon lamp, and the subsequent measurement of physical properties. As a result, about plastics, changes were confirmed in case of having no prescription of weatherable stabilizer, and changes in property values were in the range of prediction in case of having prescription. About rubber, changes in physical property after the direct exposure test were large in the U.S. and Indonesia. The effect of antioxidant was recognized. (NEDO)

FY 1999 Report on the technical results. Research and development project for quick-effect type international standards for creating new industries (Standardization of quality and testing methods of automobile fuels and lubricants); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Jidoshayo nenryo nado no seihin hinshitsu shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is conducted for the method of evaluating the effects of fuel oils on automobile engines (combustion chamber deposit), testing of valve trains of diesel engines, and testing the effects of gasoline engine oil on oil seal rubber (oil seal compatibility), with the objective to propose the international standards. In the study of the combustion chamber deposit, the combustion chamber deposit method is applied to the road running mode, to clarify that this method is well correlated with the market conditions. In the study of wear of the valve train of diesel engines, the two diesel engine oils, now adopted by the European valve train wear testing method, are applied to the JASO testing method, to clarify that the JASO method is internationally applicable. It is concluded that these two methods can contribute to the international standardization. In the study of the oil seal compatibility, the effects of testing period and engine oil type are investigated, to clarify that this method should be further developed to serve as the international standard. (NEDO)

Technology for semi-endless use of lubricating oil, no waste oil, improvement of reliability and keeping high thermal efficiency in engines; Jinzo kino seijo gijutsu ni yoru engine oil no han`eikyu shiyo to haiyu zero, oyobi shinraisei kojo to netsukoritsu teika no boshi (joyosha ni yoru shiken oyobi truck ni okeru jitsuyoka)

Energy Technology Data Exchange (ETDEWEB)

Azuma, T [Teikyo University, Tokyo (Japan); Sumimoto, M; Kimura, I

1997-10-01

The authors have developed a new technology which enables it to use lubricating oil almost forever without any waste oil, only compensating lost oil and additives. The system has been working well in many marine and co-generation diesel engines. These engines have been also free from most of engine troubles. This paper reports the test results made on a car and some trucks. Besides above mentioned advantages, the results show that high thermal efficiency has been kept for more than ten years in the car tested and that the exhaust gas brake is much improved in the trucks. 8 refs., 4 figs.

Fiscal 2000 report on result of development project of marine resources utilization system for energy conservation. Development of marine resources utilization system for energy conservation (Model demonstrative research and basic study); 2000 nendo energy shiyo gorika kaiyo shigen katsuyo system kaihatsu jigyo seika hokokusho. Energy shiyo gorika kaiyo shigen katsuyo system kaihatsu (model jissho kenkyu oyobi kiban kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

This paper explains the development of marine resources utilization system for energy conservation. The conceptual system is designed to take a large amount of deep sea water of 100 thousand to 1 million tons a day, to utilize it from the viewpoint of energy conservation using its coldness and purity characteristics, to then discharge it to the area of the sea in minimizing the environmental effect as well as obtaining effect such as absorption of carbon dioxide gas through cultivation of phyto-plankton. In pump-up technology, a piping system attaching on sea bed or floating with one or multiple constraints is applicable at present to all sites of geographical and oceanographic conditions. In utilization technology, use of deep-sea water as cooling water at a steam power plant, for example, improves generation efficiency by one point or more. In discharge and environment-related technologies, the research revealed that the deep-sea water from 300 m below releases carbon dioxide gas at surface, while photosynthesis can absorb the gas in the process of using nutrition contained in the deep-sea water; therefore, comprehensive examination is necessary taking energy utilization effect into account. Candidate sites were selected in areas of 200 m depth and within 5 km off-shore, with the optimum system examined at each site. (NEDO)

FY 1998 report on the results of the New Sunshine Project - Development of the commercialization technology of the photovoltaic power system. Verification study of the photovoltaic power system - Research on engineering methods for cost effective PV installation; 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (tashu secchi koho no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting installations of PV system and making use of the unused space for which a rise in the PV demand equal to that in houses, building roofs, etc. is expected, examination/research for much newer forms of land installation are proceeded with, and evaluation/verification of reliability/durability are conducted of new installation processes using thin film solar cells, adhesives, etc. In this fiscal year, study of the development/verification of low cost floating pedestal was promoted, and at the same time, examinational study of forms of land installation was made. As to the development of low cost floating pedestal, the module type flexible floating pedestal was developed as a small prototype pedestal and tested for installation in a pool. Survey was also carried out of geometry, mooring systems, materials, design conditions, and existing instances of different floats, and measures were studied for the effective use of the floating system. In relation to reliability and durability evaluation of the new installation process, the verification operation of evaluation facilities for various installation processes was continued, and the power generation capacity was made clear in special forms of installation such as installations on vertical/horizontal surfaces. And the study was made of the large area frameless structure, building use double glass structure, and durability of the adhesive/adhesive tape process of thin film solar cells. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Demonstrative research on photovoltaic power generation system (Study on grid interconnection technique for dispersed photovoltaic systems under high-density connection); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (komitsudo renkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Interconnecting photovoltaic systems with power transmission systems under high density affects power quality, protection, maintenance and stability of the transmission lines. As measures to deal with this issue, investigations are being made on (1) elucidation of effects imposed on transmission lines, (2) establishment of countermeasure technologies, and (3) technological options leading to higher value addition. In Item (1), with an objective to identify the current status, evaluations were given on prevention of independent operation of commercially available inverters, and on their stabilizing performance against system fluctuation. The evaluations were performed by conducting a test for multiple unit operation in parallel and a single unit performance test. The test result indicated that, while the prevention performance can be satisfied, maloperation has occurred frequently due to the system fluctuation, and that voltage rise due to the inverter was suppressed effectively by using the simultaneous control of active and reactive powers. In Item (2), a demonstration test was launched on an inverter incorporating a new prevention device. The effective means to suppress voltage rise in the high-voltage power transmission lines is the discrete voltage suppression by controlling reactive power. In addition, a proposal was made on a new voltage and phase detection method that can be used at short circuit of the high-voltage transmission lines. In Item (3), having a photovoltaic system contain a small size batteries was found effective in suppressing the power generation output variation, and in smoothing the loads. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Demonstrative research on photovoltaic power generation system (Research on multi-hybrid photovoltaic power generation system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (taiyoko hatsuden multi hybrid system no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A multi-hybrid system integrating photovoltaic and wind power generation systems with the existing diesel engine power generation system was assumed for installation in power systems in islands. System analyzing simulation and economic performance analyses were performed to consider system configurations suitable for islands from the viewpoints of system stability and economic performance. The work was progressed by dividing the subject into (1) research on the system configurations, and (2) studies on the economic performance. In performing either work, the power demand was classified as large (in Miyako Island), medium (in Kume Island) and small (in Tarama Island), and the introduction years into 1997, 2000, and 2005. In Item (1), the system parameter specifications were put into order, and the system analyzing simulation was performed, wherein it was verified that the system will be stabilized by introducing a system stabilizing equipment (batteries and an inverter) and by limiting the output from the wind power generation. In Item (2), it was made clear that the power generation cost is equivalent to or lower than the present cost, making reduction in fuel consumption possible. It was also disclosed that the introduction is most effective in small islands, and drop in the power generation amount due to limiting the output from the wind power generation is small. (NEDO)

Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

Report on survey project for demonstration of warm sea water bathing facilities using unutilized resources such as wastes in islands by carbonizing them into energy; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Rito ni okeru haikibutsu tou mikatsuyo shigen no tanka energyka no kaisui on'yoku shisetsu heno jissho chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

Surveys and discussions have been performed in Yuge Town in Ehime Prefecture for aiming at promotion of district development and zero emission in islands by carbonizing general wastes (household refuses and business operation wastes) and bamboos in the islands to utilize their energies as a substitute for the heat source of the warm sea water bathing facilities, as well as utilizing the produced carbides as soil improving materials or deodorants. The surveys were performed on bamboo carbonizing and gas carbonizing technologies, energy utilization feasibility, analysis of wastes composition, and identification of quantity of bamboos in existence. In discussing the energy utilization system by means of carbonization, it was revealed that the introduction of the bamboo carbonizing and gas carbonizing technologies can sufficiently satisfy the heat demand of the Yuge Town community facilities, although the amount of heat that can be supplied may vary because of difference in the technical processes. Also with regard to the problems of dioxins contained in the discharged gas and the problems of heavy metals contained in the carbides, it was discovered that different environmental criteria can be met as evidenced by the existing demonstration data. (NEDO)

Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (recovering facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo system kyodo jissho jigyo (kaishu setsubi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the achievements of the discussions in fiscal 1998 on the recovering system for coal bed methane gas to be supplied to the city of Tieling in China. The paper puts on record the associated documents, and figures and drawings. The associated documents appearing in the paper include the table for explosion-proof examination on the recovering devices, a parts list for the RK-3A type test drilling machine, and its operation manual. Specifications for the test drilling machine (including those for the sealing pumps), specifications for the mouth facilities, and device lists are shown. Test drilling device arrangement drawings and standard drilling record table are also described. Central blower specifications, a back-fire preventing device, a device to prevent well exterior from freezing, and a summarized drawing for drain remover for gas induction for the Daixing mine are explained. The schemes for induction and sealing, specifications and procedures for observation devices are shown. Specifications for sealing materials and the centralized monitoring facilities are also touched on. The safety measures, measures taken for power failure in the centralized monitoring facilities, and the control organization are described. Test drilling cost simulation and environment assessing methods are also described. The figures and drawings presented include the topographic map, Daixing mine cavity drawing, pipeline network, and chart for representative test drilling columns near the coal beds were also presented. (NEDO)

Study on climate control of dwellings using underground air tunnel in the cold region. Part 1. Cooling performance of the underground air tunnel connected to a small-scaled test house; Kanreichi ni okeru chika air tunnel ni yoru junetsukankyo kaizen ni kansuru kenkyu. 1. Shokibo shiken kaoku ni okeru kaki no ryobo seino hyoka

Energy Technology Data Exchange (ETDEWEB)

Miki, Y; Sanji, H; Ito, J; Komoda, T; Mitsuoka, K; Mogami, S [Kitami Institute of Technology, Hokkaido (Japan)

1997-11-25

Underground air tunnel is provided for cooling an experimentally built small house and the cooling performance is examined at Kitami Institute of Technology, Hokkaido. The house is provided with 120mm-thick layers of insulating material under the floor and inside the side walls and partitioning walls. The windows are equipped with blinds, with reed screens positioned outside to cover the windows. The air tunnel is a hard vinyl chloride tube, 200mm in internal diameter. It is buried 4.5m deep in the ground, and extends as long as 27m. A filter-provided 72W blower installed at the tunnel outlet is driven to force air through. As for the natural soil temperature in summer, it is found variable between 7.2 and 8.5degC. As the result of the experiment, it is found that thanks to the underground tunnel the room temperature is kept below 27degC even when the maximum temperature in the daytime is 30degC or higher provided the air flow is appropriately regulated. In this experiment, the maximum rate of instantaneously removed heat is approximately 2.5 times higher than the values in other previously reported experiments. The daily coefficient of performance is 6.5-11.1, again higher than the previously reported values. Different from application in warm regions, the effect of rise in the surrounding soil temperature on the cooling performance is not so conspicuous. 3 refs., 12 figs., 1 tab.

Fiscal 1997 report on the results of the international standardization R and D. R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Rinsangata nenryo denchi no kasoku jumyo shiken hoho no hyojunka ni kansuru kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As for fuel cells, which are expected as a new clean energy, the R and D are being proceeded with in various fields of the world, but the standardization has not been made both in Japan and abroad. In Japan, the situation is that the information on technical terms, indication method, performance test method, and environment/safety test methods of the phosphorous acid fuel cell power generation is publicly spread. In relation to the international promotion of fuel cells to be predicted, it is necessary to internationally standardize cells themselves which are a key component of fuel cell power generation facilities. Phosphorous acid fuel cells are expected of the earliest commercialization of all, but the common test method to evaluate life characteristics of the cell stack has not been established yet. In the R and D, for the purpose of internationally standardizing test methods to evaluate life characteristics of the cell stack, a study on the acceleration life test method of phosphoric acid fuel cells was conducted in terms of the technical trend, data, standard, etc. A plan was prepared on general rules of the method to test acceleration life at the cell reaction part of the small cell, and activities also were started for setting up a technical committee for the fuel cell power system in President`s Advisory Committee on Future Technology. 29 figs., 20 tabs.

Report on achievements in fiscal 1999 on the project for research and development of an intellectual base creating and utilizing technology. Development of a screening test method with high accuracy for internal secretion disturbing substances; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu. Naibunpi kakuran busshitsu no koseido screening shiken hoho no kaihatsu oyobi data kiban seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on developing a screening test method with high accuracy for internal secretion disturbing substances. Development was made in cooperation with the OECD on the screening method that uses as a parameter whether a chemical substance has a hormone-like activity. For the womb breeding assay method to evaluate a feminine hormone-like activity, a reproducibility and comparison test was performed on womb breeding in immature rats administered with ethinylestradiol, the administration routes, and animals used (young and weak rats, and rats whose ovaries have been extracted). In order to evaluate a masculine hormone-like activity, the basic data were collected to develop the Hershberger method, and participation was made in the OECD verification tests. Discussions were given on comparison on castrated and non-castrated rats when 17 {alpha}-methyltestosterone was administered, the administration period of time and reproducibility when immature rats were used. The Hershberger method reactivity was discussed on rats relative to estrogen. In a toxicity test using 28-day repetitive administration, bisphenol A gave impacts on the kidney, the stomach and intestine tubes. (NEDO)

Reports on 1977 result of Sunshine Project. Research for detailed design of coal gasification plant (studies on operating conditions 'pressurized hydro-fluidized gasification method', dissolution of research equipment); 1977 nendo sekitan gas ka plant no shosai sekkei no tame no shiken kenkyu seika hokokusho. Unten joken no kenkyu 'kaatsu suiten ryudo gas ka hoshiki' kenkyu kaitai

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-31

The pressurized hydro-fluidized gasification method is such that coal is hydro-gasified under a pressure of 30kg/cm{sup 3} to produce a methane-rich calorie gas. This method is a combination of three independent processes, namely, (1) thermal cracking of coal, (2) hydrogasification of thermally decomposed product, and (3) water gasification for self-contained hydrogen, and is a continuous gasification method in which all processes are operated in a fluidized bed. In fiscal 1976, an operation technique was found in which conditions suitable for each reaction purpose were given to a detached thermal cracking furnace and hydrogasification furnace and in which continuous gasification was still maintained without an adverse effect between the two furnaces. This year, the continuous gasification test will be implemented successively, determining suitable operating conditions for the purpose of increasing methane concentration and improving gasification efficiency, and concurrently extracting device-related problems that impair the continuous operation. With the aim of obtaining a self-contained system for hydrogen, water gasification tests will be conducted, with the optimum conditions determined for the water gasification. An operation test will be carried out for an internal heat type control box, so that the functions under pressurization, durability and operation criteria will be determined. (NEDO)

Achievement report for fiscal 1999 on project for supporting the formation of energy/environmental technology verification project. International joint verification research project (Verification project relative to ignition and NOx reduction using plasma sub-burner in pulverized coal-fired furnace); 1999 nendo plasma sabubana ni yoru bifuntan nenshoro ni okeru chakka oyobi NO{sub x} teigen gijutsu ni kansuru jissho project seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project is executed through the cooperation of a Russian research institute, Akita Prefectural University, and the Ishikawajima-Harima Heavy Industries Co., Ltd. In the development of a plasma sub-burner and the basic research for its verification, a pulverized coal burning plasma sub-burner is designed and fabricated, a basic burning experiment is conducted for the plasma sub-burner, and plasma stabilization in a pulverized coal flow is simulated. In the verification study of the ignition by the plasma sub-burner in a pulverized coal-fired furnace, it is found that the newly-developed plasma sub-burner satisfies the prescribed operating conditions in the system and that the ignition of pulverized coal takes place across the air ratio range of 0.5-1.5 when pulverized coal is fed to the sub-burner. It is also found that NOx is reduced a great deal when a plasma operating on an orifice gas of air or nitrogen is generated in a gas which contains NOx. (NEDO)

Report of National Research Institute for Pollution and Resources for fiscal 1979. Research on conversion of coal to petroleum, research on coal liquefaction, high pressure liquid phase hydrogenation of coal by continuous test equipment, and manufacture of coal chemicals; 1979 nendo sekitan no yuka no kenkyu / sekitan no ekika no kenkyu / renzoku shiken sochi ni yoru sekitan no koatsu ekiso suisoka bunkai / coal chemicals no seizo

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-07-01

Research was conducted on conversion of coal to petroleum for the purpose of securing substitute liquid fuel. Recovery of hydrogen from the waste gas from the conversion process was explained, as were the conversion results from various coals produced in Japan. In coal liquefaction researches with the aim of manufacturing artificial petroleum, a report was made on each of the researches, i.e., the experiment results of coal liquefaction using various catalysts, manufacture of hydrogen by water gas reaction, catalytic action against coal paste, action of mixed oil and pressure against coal paste, result of hydrogen adding test for coal paste using an intermediate scale device, test result of secondary hydrogen addition for coal liquefied oil, and the test result of continuous secondary hydrogen addition for the liquefied oil. In the manufacture of fuel oil by hydro-cracking of coal or tar, a report was made on high pressure liquid phase hydrogenation of coal using a continuous testing device. Aromatic chemicals useful as chemical materials are supposed to be obtained by cutting inter-polymerized-unit bonding to make low molecules from the chemical structure of coal, removing surrounding radicals and simplifying it. A report was also made on the experiment of manufacturing coal chemicals by combination of high pressure liquid phase hydrogenation and hydro-dealkylation. (NEDO)

Fiscal 1996 project on the modeling for effective energy consumption in developing countries under a consignment from NEDO. Recent on the results of the demonstrative study on scrap preheater of electric furnace in the iron making process (for public); 1996 nendo hatten tojokoku energy shohi koritsuka model jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Seitetsu katei ni okeru denkiro no genryo yonetsu sochi ni kakawaru jissho kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Indonesia is the biggest iron steel producing country in the ASEAN countries. Most of the production is produced by the electric furnace method in which iron steel scrap is used as a material. However, an energy saving measure in this method, the electric furnace scrap preheater using flue gas, has not yet been spread on a full scale. This R and D is aimed at developing jointly with Indonesia an electric furnace scrap preheater for medium/small size electric furnaces which are adoptable to the present iron making situation in Indonesia and installing it to the electric furnace of the iron making plant in Indonesia for a demonstrative study on energy saving, etc. Spread/expansion of the electric furnace scrap preheater which is an excellent energy saving system targeted expansion of energy saving technology not only of Indonesia, but of ASEAN countries and Japan. In this fiscal year, remodeling of part of the system was made by change of flue gas flow for increasing the energy saving effect, and at the same time, a research study was made of a scrap reheater effective as a total system. Moreover, the paper investigated technical data/information in Japan and overseas. 3 figs., 9 tabs.

FY 1998 report on the results of the New Sunshine Project - Development of the commercialization technology of the photovoltaic power system. Verification study of the photovoltaic power system - Research on engineering methods for cost effective PV installation (Data book. Survey of examples of PV systems in the world); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system no jissho kenkyu (tashu secchi koho no kenkyu kaihatsu (bessatsu data shu sekai no taiyoko hatsuden system jirei chosa))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of promoting installations of PV system and making use of the unused space for which a rise in the PV demand equal to that in houses, building roofs, etc. is expected, examination/research for much newer forms of land installation are proceeded with, and evaluation/verification of reliability/durability are conducted of new installation processes using thin film solar cells, adhesives, etc. In this fiscal year, for the purpose of contributing to the study to be widely made on various installation processes, the actual survey was conducted of various applications of the system which are being planned and introduced in Japan and abroad. Emphasis was placed on making new forms of installation applicable to Japan clear. Concretely, in addition to the study of new examples, the following were conducted: renewal of existing details of the survey, and electronic filing of system block charts/pictures as a key to the information supply by electronic media such as CD-ROM. Also conducted was a study for translating the contents into English or writing them both in Japanese and English. Further, the database was made newer using these results of the most up-to-date survey, and at the same time, the results were indicated of the statistical analysis of the usage, system form, power generation scale and element equipment of various systems. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D on the improvement of reliability of photovoltaic power generation - Investigative study of long-term reliability of inverter - Separate volume: Data on the life evaluation test); 2000 nendo New sunshine keikaku seika hokokusho(Sokatsu ban). Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Taiyokohatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - Inbata no choki shinraisei no chosa kenkyu - Bessatsu : Jumyo hyoka shiken datashu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing a life evaluation method for power conditioner of about several kilowatts for general housing use, the acceleration test was made, and the data were summarized for maintenance of power quality, cooperation with the protection system at power system, insuring of safety of personnel/facilities, etc. As to the acceleration method, by paying attention to heat deterioration of thermal plasticity materials being used for power conditioner and by using the acceleration method using the 10-degree C half law by the Arrhenius law, temperature and humidity were set at 40 degrees C and 36%, respectively. The operation hour and stopping time were fixed at 3.5 hours and 4.5 hours, respectively. The life evaluation measurement by the acceleration test was composed of the continuous evaluation measurement with the aim of early finding the degradation of performance, anomaly, etc. of power conditioner and of the evaluation measurement at specified intervals with the aim of precisely measuring the state of degradation of power conditioner. As a result of the continuous evaluation measurement, the paper reported the data on the rise in temperature inside the power conditioner during the acceleration test and the change in electric characteristics of input/output. (NEDO)