WorldWideScience

Sample records for kaiyo shigen sogo

  1. Fiscal 1997 achievement report. Research and development of comprehensive basic technology on marine resources; Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu sogo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The deep-sea manganese nodule mining system in this report collects efficiently and continuously a large quantity of manganese nodules in existence in the 5,000m-deep sea floor. The aim of the project is to develop and build an experimental system for a real mining machine and to perform a comprehensive marine test to find out if such a real machine is technologically and economically feasible. The system under this project is divided into four systems, which are a nodule mining system, nodule lifting system, nodule handling system, and a measurement control system. The nodule mining system travels on the sea bottom efficiently collecting manganese nodules and forwarding them into the nodule lifting system. Only a few systems of this kind have so far been developed, however, and therefore much endeavor needs to be exerted for the development of technologies involved. The nodule lifting system is divided into a pump lift unit, air lift unit, and a nodule lifting pipe. The pump lift unit and air lift unit elevate manganese nodules supplied from the nodule collecting unit to the sea surface. The nodule lifting pipe provides a passage for nodules to run through upward. (NEDO)

  2. Report on final evaluation of industrial science and technology research and development system. Comprehensive basic technologies for development of ocean resources. Manganese nodule exploitation system; Kaiyo shigen sogo kiban gijutsu (mangan dankai saiko system). Saishu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    Described herein are the final evaluation results of the basic research and development of the system for exploiting manganese nodules as one of ocean resources. A 9-year project was started in the FY 1981 to establish the techniques to efficiently, economically exploit Mn nodules on a commercial basis, which are occurring on deep sea bottoms (4,000 to 6,000 m deep), in order to stably supply non-ferrous metallic resources, e.g., Ni, Cu, Co and Mn, which are essential for economic activities of Japan. Originally, the UN convention related to ocean laws raised development of unique exploitation techniques as the prerequisite condition for obtaining the right to develop Mn nodules. However, the situations around development of Mn nodules were changed since then, to devalue objects, significance and urgency of this project. The fourth amendment of the basic plans decided to suspend the comprehensive ocean tests in 1996, and to implement only the ocean/land tests in which part of the individual elementary techniques were combined. Therefore, the technological validation of the overall system could not be done sufficiently, and degree of achievement of the project is low, viewed from insufficient prospects of the commercial production. However, this project produced good results in individual elementary techniques, which are of significance for the resources policies. (NEDO)

  3. Fiscal 1997 report on the R and D project consignment from NEDO on industrial science and technology. R and D on total base technology for marine resources (Mn nodules mining system) (total system (experimental plan)); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho (total system (jikken keikaku) hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the design of experiments for confirming the technological and economical feasibility of commercial production of Mn nodules. An experimental sea area was selected considering Mn nodule characteristics such as concentration, continuity of nodule distribution and nodule size, and sea bottom topographic features such as flatness and exposed bed rock disturbing traveling of nodule collectors. The experimental plan was decided on the basis of the survey and study on an experimental scale, various requirements, weather and sea weather features of the sea area, and sea bottom conditions. Based on the experimental plan, various verification tests and simulation analyses were carried out, and functions of various equipment were confirmed. The conceptual design of a mining system assumed both pump-lift and air-lift systems, and yearly production rates of 2 and 3 million tons by 2 mining barges, and summarized main points of every system. As the evaluation result, the future direction of commercial production of Mn nodules was clarified to a certain extent. 5 figs., 21 tabs.

  4. Achievement report for fiscal 1995 on the research and development of comprehensive basic technologies on marine resources (manganese nodule mining system) in industrial and scientific technology research and development project. Trends and forecasts of the supply-demand for metal resources (Ni, Co, Cu, Fe, Mn) that are contained in manganese nodules; 1995 nendo kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (mangan dankai saiko system) seika hokokusho. Mangan dankai ni kakawaru kinzoku shigen (Ni, Co, Cu, Fe, Mn) no kyokyu ni kansuru shorai doko no suitei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    Living standards improving in developing countries especially in China are the most influential factor to determine the demand for Cu. Consumption of Ni will depend on the trends of advanced technologies such as Ni-hydrogen battery, fuel cell, shape memory alloy, hydrogen absorbing alloy, in addition to increase in global population and developing countries' living standards improvement. Co is far more dependent on advanced technologies than Ni is. On the land, Ni ore is increasingly lower in quality and Co is being retrieved from by-products of Cu production, both meeting the problem of unstable supply. Consideration is made to apply new extraction methods to Cu production; there are some potential resources for Fe and Mn. The Mn nodule exists in great quantities and is a attractive source of supply, but a long time will be required before it is exploited. It is necessary to speed up the study to exploit the Mn nodule, but first of all the problem of its competition with land resources in terms of cost has to be solved. It needs to be found out at what stage of production the Mn nodule is competitive with land products. In any case, Japan should undertake the efforts of marine resources exploitation leading other countries of the world. (NEDO)

  5. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  6. Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-06-01

    A high speed towed type physical and chemical observation marine robot named as `Flying Fish` has been developed since 1992, which can measure chemical substances in the sea as well as physical data, such as flow velocity of the ocean and water temperature. This paper describes its formation, designing, control system, and results of ocean tests. For the space continuous observation of physical, chemical, and biological quantities, it is essential to control the depth, pitch, and roll. The wing control method was employed for this robot. As a result of the ocean tests, the following conclusions were obtained. The accuracy under the steady state was {plus_minus}0.05 m in the depth, {plus_minus}1 degree in the pitch, and {plus_minus}0.5 degree in the roll. This was stable enough to operate chemical analysis, such as dissolved oxygen analysis. Even under the unsteady state during the change of depth, the pitch and roll were controlled in {plus_minus}3 degree and {plus_minus}0.5 degree, respectively. Results of the field tests and the numerical simulations for the performance of this robot were agreed well mutually in the practically sufficient accuracy. 10 refs., 15 figs., 2 tabs.

  7. Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Kaiyo kankyo sogo kansoku robot `flying fish` no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Koterayama, W.; Yamaguchi, S.; Nakamura, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Akamatsu, T. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-12-31

    With an objective for spatial continuous measurement of physical, chemical and biological amounts in ocean, development has been made on a wing controlled towed vehicle, `Flying Fish` which is capable of controlling depth, pitch and roll. Numerical simulations and two-year sea experiments have been carried out for the development. Flying Fish consists of a sub-system comprising a towing vehicle, towing cables, and on-board controllers. In a steady state, Flying Fish can be controlled at accuracy for depth of {plus_minus} 0.05m, pitch of {plus_minus} one degree, and roll of {plus_minus} 0.5 degree. This accuracy is sufficient for operating a chemical analyzer, the dissolved carbonic acid analyzer. Even in a non-steady state such as in changing the depth, the pitch can be controlled at {plus_minus} 3 degrees and the roll at {plus_minus} 0.5 degree. This extent of attitude change is within a range rendering no problems in maintaining accuracy of the measurement devices. The result of sea experiments for movements of Flying Fish agreed with that of the numerical simulation at practically usable accuracy. Flying Fish is verified as an effective system in investigating spatial variations in ocean data. 10 refs., 15 figs., 1 tab.

  8. Temperature, salinity and other variables collected from discrete sample and profile observations using CTD, bottle and other instruments from Kaiyo in the Philippine Sea from 1994-02-12 to 1994-02-16 (NCEI Accession 0143635)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0143635 includes discrete sample and profile data collected from Kaiyo in the Philippine Sea from 1994-02-12 to 1994-02-16. These data include DELTA...

  9. Fiscal 2000 report on result of development project of marine resources utilization system for energy conservation. Development of marine resources utilization system for energy conservation (Model demonstrative research and basic study); 2000 nendo energy shiyo gorika kaiyo shigen katsuyo system kaihatsu jigyo seika hokokusho. Energy shiyo gorika kaiyo shigen katsuyo system kaihatsu (model jissho kenkyu oyobi kiban kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This paper explains the development of marine resources utilization system for energy conservation. The conceptual system is designed to take a large amount of deep sea water of 100 thousand to 1 million tons a day, to utilize it from the viewpoint of energy conservation using its coldness and purity characteristics, to then discharge it to the area of the sea in minimizing the environmental effect as well as obtaining effect such as absorption of carbon dioxide gas through cultivation of phyto-plankton. In pump-up technology, a piping system attaching on sea bed or floating with one or multiple constraints is applicable at present to all sites of geographical and oceanographic conditions. In utilization technology, use of deep-sea water as cooling water at a steam power plant, for example, improves generation efficiency by one point or more. In discharge and environment-related technologies, the research revealed that the deep-sea water from 300 m below releases carbon dioxide gas at surface, while photosynthesis can absorb the gas in the process of using nutrition contained in the deep-sea water; therefore, comprehensive examination is necessary taking energy utilization effect into account. Candidate sites were selected in areas of 200 m depth and within 5 km off-shore, with the optimum system examined at each site. (NEDO)

  10. Dissolved inorganic carbon, temperature, salinity and other variables collected from discrete sample and profile observations using CTD, Coulometer for DIC measurement and other instruments from the Kaiyo in the North Pacific Ocean and South Pacific Ocean from 1997-11-29 to 1997-12-25 (NODC Accession 0112363)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NODC Accession 0112363 includes chemical, discrete sample, physical and profile data collected from Kaiyo in the North Pacific Ocean and South Pacific Ocean from...

  11. Dissolved inorganic carbon, temperature, salinity and other variables collected from discrete sample and profile observations using CTD, bottle and other instruments from the KAIYO-MARU in the East China Sea (Tung Hai) and Philippine Sea from 1996-06-20 to 1996-07-15 (NODC Accession 0115023)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NODC Accession 0115023 includes chemical, discrete sample, physical and profile data collected from KAIYO-MARU in the East China Sea (Tung Hai) and Philippine Sea...

  12. Dissolved inorganic carbon, pH, alkalinity, temperature, salinity and other variables collected from discrete sample and profile observations using CTD, bottle and other instruments from the KAIYO-MARU in the North Pacific Ocean and Philippine Sea from 1994-01-07 to 1994-02-10 (NODC Accession 0115007)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NODC Accession 0115007 includes chemical, discrete sample, physical and profile data collected from KAIYO-MARU in the North Pacific Ocean and Philippine Sea from...

  13. Partial pressure (or fugacity) of carbon dioxide, dissolved inorganic carbon, alkalinity, salinity and other variables collected from Surface underway observations using Autonomous sensor to measure dissolved inorganic carbon (DIC), Carbon dioxide (CO2) gas analyzer and other instruments from Kaiyo in the Bismarck Sea, Celebes Sea and others from 1994-01-06 to 1999-11-21 (NODC Accession 0080984)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0080984 includes Surface underway, chemical, meteorological and physical data collected from Kaiyo in the Bismarck Sea, Celebes Sea (Sulawesi Sea and...

  14. Dissolved inorganic carbon, pH, alkalinity, temperature, salinity and other variables collected from discrete sample and profile observations using CTD, bottle and other instruments from KAIYO-MARU and MIRAI in the North Pacific Ocean from 1999-05-23 to 1999-09-10 (NODC Accession 0115168)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0115168 includes biological, chemical, discrete sample, physical and profile data collected from KAIYO-MARU and MIRAI in the North Pacific Ocean from...

  15. Dissolved inorganic carbon, pH, alkalinity, temperature, salinity and other variables collected from discrete sample and profile observations using CTD, bottle and other instruments from the KAIYO-MARU in the North Pacific Ocean and Philippine Sea from 1996-06-17 to 1996-07-02 (NODC Accession 0115016)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NODC Accession 0115016 includes chemical, discrete sample, physical and profile data collected from KAIYO-MARU in the North Pacific Ocean and Philippine Sea from...

  16. R/V KAIYO cruises from 1995-2000 collecting CTD, XCTD, and dissolved oxygen data in support of the Tropical Ocean Climate Study in the Tropical Western Pacific (NODC Accession 0048913)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set includes 10 cruises of the R/V Kaiyo of the Japan Marine Science and Technology Center conducted in 1995-2000 as part of the Tropical Ocean Climate...

  17. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Development of systems for marine organism resources classification and utilization (Achievement report); 1998 nendo kaiyo seibutsu nado shigen no bunrui riyo system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Genetic resources and databases involving microbes and the like were conserved and amplified for the reinforcement of biotechnology industries. In the maintenance of marine microalga culture collection, 16S rDNA sequences were determined for 120 strains of Cyanophyceae isolated by Marine Biotechnology Institute Co., Ltd., and databases were prepared containing the results of molecule classification, history of each strain, and pictures obtained using optical microscopes. In the maintenance of marine bacterium culture collection, methods for identifying by molecule classification bacteria separated from the sea were simplified and unified, and genera were identified for 776 strains. In the development of systems for classifying and conserving subtropical microbial resources, base sequences were analyzed for 14 strains of six kinds of microbes such as Aspergillus awamori conserved at Institute of Applied Microbiology of University of Tokyo. Other efforts included the enrichment of marine microalga collections, construction of an embryo bank system, advanced classification of microbes, and development of a DNA (deoxyribonucleic acid) analyzing system. (NEDO)

  18. Partial pressure (or fugacity) of carbon dioxide, salinity and other variables collected from Surface underway observations using Carbon dioxide (CO2) gas analyzer, Shower head chamber equilibrator for autonomous carbon dioxide (CO2) measurement and other instruments from KAIYO-MARU in the Hawaiian Islands Humpback Whale National Marine Sanctuary, North Pacific Ocean and others from 1987-10-28 to 1987-12-05 (NODC Accession 0080985)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0080985 includes Surface underway, chemical, meteorological and physical data collected from KAIYO-MARU in the Hawaiian Islands Humpback Whale...

  19. Comprehensive research concerning the development of effective utilizing techniques of biological resources (large scale research out of the framework). Seibutsu shigen no koritsuteki riyo gijutsu no kaihatsu ni kansuru sogo kenkyu (ogata betsuwaku kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-25

    This paper is a research report in which the cultivated production of forest resources, the development to useful substances and the systematization to take the root in a region were studied. The distribution maps of biological resources on respective woodland systems: that is, the nationwide distribution maps of the amount of resources in Japan as to the broadleaf trees in private forests and national forests, the available amount and kinds of tree were prepared. As for the establishment of cultivation technique of the super-short deforestation forest, that is, pursue of wooden growth to the maximum limit, the superior clone 26 system was selected from the willow group through the research of wooden cultivation and the clone which showed the maximum yield reached 24t/ha every year. As for the material preparation technique due to microbial enzymes, that is, the creation and breeding of fungi which have the high lignin decomposition power, a stock of fungi which has the high lignin decomposition power and the decomposition selectivity was created by the cell fusion and the UV (ultraviolet ray) radiation treatment. As for the use of effective components in wooden resources, many useful characteristics could be detected by applying the boiling, bursting and ozone treatment. As for the mushroom cultivation through the application of unused tree kinds, a new kind of mushroom for food service was selected to clarify the possibility of fruit body formation. The development of a new material from conifers is promising. 1 tab.

  20. International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

  1. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  2. Report for fiscal 1980 on comprehensive survey for nationwide geothermal resources. Survey on Curie point method (Associated material - operation flight report); 1980 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Curie tenho chosa (futai shiryo sagyo shinchoku hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-10-01

    With an objective to identify the status of distribution of deep underground thermal structure, aerial magnetism investigations were executed in the south Kyushu area, and data used in the Curie point method were collected. This paper summarizes the progresses and achievements of the work during the investigation. The report for April 1981 summarized preparation of equipment and materials by EG and G Geometrics Corporation, and the work schedules with the Idemitsu Geothermal Development, Petroleum Resources Development, and Naka-Nippon Airways. The report for April 22 compiled the site preparation and the test flight. The report for April 28 compiled the calibration and magnetism compensation flight. The report for May 5 compiled the implementation of the second flight , and the result of survey for 292 km in total. The report for May 10 compiled the implementation of the third to fifth flights, and the results of measurements for 584 km, 519 km and 360 km, respectively. The report for May 18 compiled the implementation of the sixth to eighth (final) flights, and the results of measurements for 513 km, 584 km and 68 km, respectively. (NEDO)

  3. Report for fiscal 1982 on comprehensive survey for nationwide geothermal resources. Preparation of lineament density maps - radar image analyses - in north-eastern area; 1982 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Lineament mitsudozu sakusei (radar gazo kaiseki (Tohoku chiiki))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    Geological structure analysis maps and lineament maps were prepared on the north-eastern area and parts of the ancillary areas thereof by analyzing radar images of a 1 to 200,000 scale. With regard to the geological structures, analyses were performed by using as the original data the north look radar images for the three special geothermal areas to have prepared the geological structure analysis maps. The analysis of the radar images identified ground bed boundary lines in more detail than in the existing geological maps, and new discoveries were made available on faults. The lineament maps were compiled by implanting into respectively corresponding topographic maps the 24 N-S lineament maps made by the west look radar images for the whole surveyed areas, and the 16 E-W lineament maps made by the north look radar images for the special geothermal areas. Based on the clarity and characteristics deciphered on the images, the lineaments were classified into the major, minor, and subtle lineaments, which were indicated on the lineament maps. The lineaments were digitized by positions of the edge points, and the histograms and statistical tables were prepared by computer processing. (NEDO)

  4. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Appendix); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei furoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    This paper explains different theoretical calculation methods used in gravity and magnetic force data analysis in geothermal resources survey. Analyzing the gravity data and the magnetic force data is capable of being applied with the potential theory. The increased speed and capacity of recent computers make easier the conversion of data into wave number zone. In relation with heavy magnetic force analysis, the paper explains such items as basic handling, IGRF remainder calculation, methods for topographic correction, conversion of primary and secondary polar magnetism and conversion of pseudo-gravity, coherent analysis, spectral ratio method, estimation of spectra by using MEM, spectrum moment method, heavy magnetic force simultaneously analyzing type modeling, constraint inversion method, and other methods. The paper further explains the sequential approximation method in magnetization calculation, methods for calculating equivalent magnetization distribution (methods by Bhattacharyya and Chan, and Nakatsuka), method for calculating equivalent magnetization distribution (method by O'Brien), primary and secondary polar magnetism conversion relation formulas, and theoretical calculation of spectral ratio. (NEDO)

  5. Report on comprehensive surveys of nationwide geothermal resources in fiscal 1979. Conceptual design of a database system; 1979 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Database system gainen sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-31

    Conceptual design was made on a database system as part of the comprehensive surveys of nationwide geothermal resources. Underground hot water in depths of several kilometers close to the ground surface is a utilizable geothermal energy. Exploration using the ground surface survey is much less expensive than the test drilling survey, but has greater error in estimation because of being an indirect method. However, integrating data by freely using a number of exploration methods can improve the accuracy of estimation on the whole. In performing the conceptual design of a geothermal resource information system, the functions of this large scale database were used as the framework. Further data collection, distribution and interactive type man-machine communication, modeling, and environment surveillance functions were incorporated. Considerations were also given on further diversified utilization patterns and on support to users in remote areas and end users. What is important in designing the system is that constituting elements of hardware and software should function while being combined organically as one system, rather than the elements work independently. In addition, sufficient expandability and flexibility are indispensable. (NEDO)

  6. Report on the research and development achievements in fiscal 1999 on the international research cooperation project for comprehensive development and utilization technologies for gas hydrate resources; 1999 nendo gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the achievements in fiscal 1999 on development of gas hydrate resources. As a result of synthesizing gas hydrates in deposit systems, identifying stability zones in compositions, and studying thermal conductivity and dielectric constant of the deposits, the estimation accuracy has been enhanced steadily in estimating hydrate existing areas in actual frost areas. In the collecting technologies, a proposal was presented for a system by which carbon dioxide is introduced into ground beds at the same time as recovering gases, and gas hydrates are displaced with carbon dioxide hydrates. The displacement phenomenon was verified experimentally by controlling temperatures and pressures. Even below the freezing point, the production rate of the carbon dioxide hydrates is fast if it is above minus 4 degrees C. Salt diffusion behavior important in control of the production and decomposition, and action mechanisms of production and suppression agents were made clear microscopically. Experimental and theoretical discussions were given on dynamics of the production and decomposition. The cage occupation rate of methane hydrates was quantitatively measured successfully by using the Raman spectroscopy. Hydrates of gas mixture were utilized to have verified the possibility of separating the gas mixture constituents. (NEDO)

  7. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  8. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal conception design (Associated material 3 - materials related to U.S. geothermal analysis contractors and consultants); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei futai shiryo 3 (Beikoku chinetsu kaiseki contractor oyobi consultant kankei shiryo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    This paper summarizes the U.S. geothermal analysis contractors, including the Aero Service Corporation, the EG and G Group, the QEB Group, and the Republic Geothermal, Inc., and the consultants, including the Remote Sensing Consultants. For the Aero Service Corporation, the paper states histories of and books written by major personnel. For the EG and G Group, the paper states the outlines of such companies as EG and G Services, EG and G Geometrics, Mars Associates, Inc., and UURI, as well as histories of and books written by major personnel. For the QEB Group, the paper states the outlines of such companies as QEB, Inc., and Eureka Resource Associates, Inc. as well as histories of and books written by major personnel. For the Republic Geothermal, Inc., the paper states the company outline, histories of and books written by major personnel. For the Remote Sensing Consultants, the paper states the history of and books written by Dr. R.J.P.L. Lyon. (NEDO)

  9. Report for fiscal 1981 on comprehensive survey for nationwide geothermal resources. Survey on radar imaging method - geothermal analysis conception design (Associated material 2 - reports on U.S. consultants); 1981 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Radar eizoho chosa (chinetsu kaiseki gainen sekkei futai shiryo 2 (Beikoku consultant hokokusho))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-10-01

    Three technical and business proposals for comprehensive analysis of the survey data for nationwide geothermal resources in Japan were submitted from three U.S. candidate contractor groups, whose evaluations were reported by the Republic Geothermal, Inc. The group comprising of the Aero Service and Golder Associates has few geological engineers, and their engineers related to physical exploration has no experience whatsoever in the geothermal field. The group comprising of the EG and G Corporation, Geometrics, Utah University Research Institute, Mars, and Republic Geothermal, Inc. requires a maximum amount of time and travel expense to adjust the implementations done by four companies. However, this is a group having the largest pan-world geothermal experience, and much experience about Kyushu area of Japan. The group comprising of QEB, Inc., Eureka, and GSC, Inc. requires considerable amount of time and travel expense because of the implementation performed by three companies. The group has some geothermal experience in America, but none whatsoever in Japan. Holding or not holding persons with geothermal experience is an important criterion in selecting the contractors. (NEDO)

  10. Report for fiscal 1982 on comprehensive survey for nationwide geothermal resources. Preparation of basic map from among maps of nationwide geothermally promising areas (south Kyushu and north Kyushu); 1982 nendo zenkoku chinetsu shigen sogo chosa hokokusho. Zenkoku chinetsu yubo chiikizu no uchi motozu sakusei (Minaikyushu oyobi Kitakyushu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    With an objective to prepare the basic map from among maps of geothermally promising areas in the south Kyushu and north Kyushu, comprehensive analysis has been performed from the standpoint of geothermal analysis by combining the data derived from remote sensing with the data obtained by different physical exploration processes. The analysis has used mainly the gravity data, magnetism data, radar lineament, and Landsat lineament, as well as the latest data processing technology and analytical methods. As a result of the analysis, the area around Kirishima in south Kyushu was indicated as the most promising area for the future geothermal development. This area contains a series of new volcanoes, has the fault systems grown widely, and is expected of existence of water permeable reservoirs in deep underground. The Kagoshima bay area and the Sakurajima Island area were also regarded promising. In the north Kyushu area, such promising areas were indicated as the Futagoyama area in which highly magnetized and high-density volcanic rocks are recognized, and moreover, penetration rocks with magnetic anomaly are recognized in wide area, the area with volcanic actions from the Pliocene period to the Quarternary period, and the area at the north latitude of 33 degrees 38 minutes, and the east longitude of 131 degrees 02 minute. (NEDO)

  11. FY 1998 report on the results of the R and D for acceleration of biological resource information basement preparation (bioinformatics). Third revision. Development of measurement technology of interaction among biological molecules (Development of high-precise automatic analysis technology for a trace amount of cellular protein); 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu kaihatsu (bioinformatics) seika hokokusho. Seitai bunshikan sogo sayo no keisoku gijutsu no kaihatsu (saibonai chobiryo tanpakushitsu no koseido jido kaiseki gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An experimental study was conducted with the aim of developing the technology to acquire/analyze in high sensitivity manifestation proteins existing in a trace amount and in various kinds, concretely, signal transfer molecules, transcription factors, etc. which exist in one cell. After extracting a trace amount of functional proteins for analysis from the specified functional cell, the study was made on the following: precise separation and detection technique for cellular proteins, efficient digestion technique and contaminant elimination technique of stained protein, precise separation of peptides by micro-LC technique, precise peptide molecular mass detection of each separated peptide with high sensitivity, reconstruction of protein structure by computer algorithm. As a result, as to the analysis level, an analysis technology with high sensitivity of a 50 fmol level was established as against the existing level of several pmol. Moreover, after the separation/digestion of proteins by the 2D electrophoresis, a series of the process automation system was completed which is high-precise separation using protein columns - molecular analysis - structure prediction by computer. (NEDO)

  12. International Ocean Symposium (IOS) 1996; Kokusai kaiyo symposium 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-18

    This is a proceedings of the International Ocean Symposium 1996. On the first day of the symposium, the following were given with a theme `The Ocean, Can She Save Us`: Underwater research and future of mankind as a commemorative speech; The ocean, can she save us -- trying to discover the true figure of the ocean as a keynote speech. Panel discussion was held on The global environment and the infinite potential of the ocean. On the second day, an approach was made mostly from a cultural aspect with a theme `The Ocean and the Japanese.` The following were given: Human links between east and west as a commemorative speech; The ocean and Japanese culture as a keynote speech; Civilization spanning across oceans as a panel discussion. The Japanese have been developing their individual technologies in shipbuilding, shipping, and ocean development, have been raised by Mother Ocean, and have lived together. Ocean has been supplying humans food, water, oxygen, marine routes, and even dream and hope. The environmental pollution is the result of the human greediness. It is fear and friendship between humans and ocean that can save humans and ocean.

  13. Mathematical structure of ocean container transport systems; Kaiyo container yuso system no suriteki kozo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Shinkai, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Chikushi, Y [Nippon Telegraph and Telephone Corp., Tokyo (Japan)

    1997-10-01

    Mathematical structure of a vessel arrangement program was discussed in order to learn roles of container ships in ocean transport systems among China, NIES/ASEAN countries and Japan. Formulation is possible on a mathematical handling method for sailing route connection diagrams between ports, a transport network to indicate container movements, a service network to indicate sailing routes, and a network generalizing them. This paper describes an analysis made on the container transport system between Japan and China, taken as an example. Four ports were selected each from Japan and China, and the statistical database for fiscals 1996 and 1994 was utilized to set models for: (a) the liner network system with transshipment at the port of Shanghai and (b) the cruising route system going through the ports of Yokohama, Nagoya and Kobe. A hypothesis was set that a consortium (coordinated ship allocation) can be implemented ideally and completely. The transport network (a) is lower by 10% in total cost than the transport network (b), resulting in 1.6 times greater productivity. Actual service network is closer to the network (b), but the system can be utilized for discussing guidelines on vessel arrangement programs with which shipping companies pursue better management efficiency under a condition that the consortium can be formed. 10 refs., 6 figs., 2 tabs.

  14. Effect of water pollution on marine organisms; Sekiyu osen no kaiyo seibutsu eno eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, M. [Okayama Univ., Okayama (Japan); Fujisawa, K. [Okayama Prefectural Fisheries Experiment Station, Okayama (Japan)

    1997-10-10

    Toxicity of petroleum component to aquatic organisms appears as a result of its deposition onto living organisms followed by its migration into bodies of the organisms, and emergence of toxicity from the migrated component. Effect evaluation processes standing on this viewpoint may include the exposure monitoring or migration monitoring, in which the petroleum component migrated into marine organisms is analyzed and the state of the component concentrated in these organisms is measured, or effect monitoring, in which actions of the petroleum component in the organisms are investigated. The effects of petroleum on aquatic organisms would include the following occurrence: direct fatal toxicity acting on cells and membranes, quasi-fatal toxicity causing death indirectly through feeding actions and abnormal actions, direct coating of oil on surface of organisms, which prevents movability and feeding actions of the organisms and reduces hydrophilicity of plumes and hairs, pollution of living organisms due to migration of carcinogenic aromatic compounds into bodies of the living organisms, and change in species compositions and geographic distribution of living organisms due to change in physico-chemical environment. This paper explains cases of detection and identification of organic sulfur compounds, aromatic compounds, polycyclic aromatic compounds, paraffins, olefins and heavy metals in parametric compounds of petroleum. 20 refs., 4 figs., 3 tabs.

  15. Study of carbon dioxide (CO sub 2 ) problems through marine science. Kaiyo kara mita nisankatanso mondai

    Energy Technology Data Exchange (ETDEWEB)

    Honda, M [Japan Marine Science and Technology Center, Kanagawa (Japan)

    1990-09-01

    This paper reviews the researches relating to carbon dioxide circulation in oceans, and introduces the roles played by oceans in respect of the CO {sub 2} problem. Oceans occupy 70% of the globe {prime} s surface area, and contain 60 times as much of carbon as in the atmosphere. However, the amount of CO {sub 2} absorbed from the atmosphere into the oceans as has been estimated to date can not explain the carbon balance on earth. The exchange rate of CO {sub 2} between the atmosphere and the oceans was estimated from measurements of the partial pressure (PCO {sub 2}), and from behaviors of the radiocarbon ({sup 14} C). However, to raise the estimation accuracy, it is necessary to obtain data from the sea areas where observations are carried out only infrequently, and from the winter season during which the observation frequency is low. Identifying variations in organic and inorganic carbon amount generated by marine organisms is also important. Since more than 99.9% of carbon is present in the form of carbonate, it is required that its amount, and the amount of precipitation and dissolution per unit time be identified, and that CO {sub 2} removed from the carbon cycle be quantified. What is particularly required is the study of open-sea bottom deposits, and the coastal study with coral reefs as the main object. 40 refs., 30 figs., 11 tabs.

  16. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M; Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T [Kyushu University, Fukuoka (Japan)

    1997-12-31

    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  17. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M.; Koterayama, W. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H. [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T. [Kyushu University, Fukuoka (Japan)

    1996-12-31

    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  18. Industry brief letter; Kasupikaioki sekiyu koku kaihatsu sekiyu shigen kaihatsu nado sannyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    4 companies of Petroleum Resources Development, Indonesia Petroleum, Teikoku Petroleum an Itochu Petroleum Development will sign petroleum exploration and development contract in petroleum mining property offshore of Caspian Sea with Azerbaijan National Petroleum Company, Sokar Company. In another mining property, Mitsui group reached conclusion with Sokar Company in mining right. Resource development competition between existing international petroleum majors and Japanese petroleum companies around Caspian Sea may be further intensified. (translated by NEDO)

  19. Recent situation and future of mineral resources in Myanmar. Myanmar no shigen no genjo to shorai

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, H

    1993-11-05

    Though being one of the most impoverished countries with a per capita national income of 225 dollars (1989) because of instability in its political situation, Myanmar is blessed with abundant underground resources. This paper describes the current status of their production and development. Oil fields located in the central sedimentary basin produces 58 million barrels of crude oil and 35 billion 650 million ft[sup 3] of natural gas, but the production is a little insufficient to meet the national demand. Petroleum production is carried out by the operating organizations and departments under the control of the Ministry of Energy. The production has been decreasing since the peak in 1984 because of aged facilities. The government is exerting efforts on production increase and developments leveraged by foreign capital investments. Coal is produced annually at 40,000 tons in the north-west area, all consumed domestically. Such natural resources as copper, zinc, lead, gold, and precious stones are produced by the operating organizations under the control of the Ministry of Mining. Although the country is blessed with an extremely great variety of underground resources, its actual situation in the national economy expects strongly cooperations from other countries including Japan. 6 refs., 2 figs., 1 tab.

  20. Leading research on next generation metal production technology; Jisedai kinzoku shigen seisan gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The energy saving environment-friendly technology for low- grade difficult-to-process ores was researched focusing attention on the hydro-metallurgical process of non-ferrous metals. This research aims at development of both effective leaching system of metals, and separation/crystallization system recognizing the property difference between metal ions in solution. The leaching system allows the inexpensive molecular level control of electron transfer, mass transfer of metal ions and stabilization of leached metal ions in a solid/liquid interface. The system thus allows selective leaching of metals from various resources such as difficult- to-leach sulfide minerals to prepare concentrated solutions. The separation system can obtain high-purity solutions including each metal ion by advanced separation/concentration technology from the solutions. The crystallization technology (including electrolysis) is developed for preparing target metal materials by molecular level control of nucleation, particle growth, thin film formation and bulky metal formation processes. Overall energy consumption is reduced to 1/3 of that of the pyro-metallurgical method, aiming at zero emission. 15 refs., 14 figs., 11 tabs.

  1. Recent situation and future of molybdenum mineral resources; Molybdenum shigen no genjo to shorai

    Energy Technology Data Exchange (ETDEWEB)

    Ono, K.; Nishiyama, T. [Kyoto University, Kyoto (Japan)

    1997-05-05

    Molybdenum is produced mainly from molybdenite, and the majority of this ore is exploited from the porphyry deposit. The reserve is estimated at 5.5-million ton. A total of 118-thousand ton was produced across the world in 1995, in the U.S., China, Chile, and Canada, the countries named in the order of quantities they exploited. Molybdenite is first refined by flotation for the production of a sulphide. It is subjected to oxidizing roasting for conversion into crude molybdenum trioxide, which is next subjected to extraction in warmed-up aqueous ammonia and then to evaporation for the crystallization of ammonium paramolybdate. The crystals are baked for conversion into molybdenum trioxide of the ordinary purity, to be further processed into ferromolybdenum, molybdenum compounds, molybdenum powder, etc. In view of the magnitude of demand, the metal is used mostly for the manufacture of special steels and special alloys. The demand for this metal, though small in size, involves important articles, such as line materials for semiconductors in the power industry, catalysts in the chemical industry, and lubricants. Japan`s stockpile includes molybdenum, but the U.S. has been stockpiling none since 1977. 9 refs., 4 figs., 1 tab.

  2. Comprehensive research cooperation in environmental technology in fiscal 1995; 1995 nendo kankyo gijutsu sogo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Cooperative study was conducted on research subjects concerning water pollution preventive technologies in China and Thailand. In China, straw pulp mills were studied which were in the Institute of Light Industry Environmental Protection and the Environmental Engineering Course of Jinghua University. The following studies were jointly conducted: survey of the water quality pollution caused by waste water, investigational study on production technology and waste water treatment technology, extraction of technologies effective to preserve water quality, study/evaluation of economical efficiency of the said technologies, etc. In Thailand, cooperative research was conducted on automatic measuring technology for factory waste water in a model industrial estate of the Thai National Industrial Estate Corporation. Items for the study were a study on measuring technology for water quality environment, an investigation on the status of water quality environment in the model industrial estate, a study on automatic measuring technology for plant waste water, a study on how to use measuring data in the model industrial estate, etc. Every study enabled technical data accumulation at every research institute through field research exchanges. 24 refs., 91 figs., 45 tabs.

  3. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  4. Resources, environment and solid waste management; Shigen {center{underscore}dot} kankyo mondai to haikibutsu shori no tenkai

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Nobuo [Kyoto University, Kyoto (Japan). Department of Environmental Engineering

    1999-09-20

    Solid waste management should be considered in close relation to conservation of energy and resources. The history and situation of solid waste management in Japan is outlined and the new concept of waste management is discussed for sustainable development. (author)

  5. Geological evaluation on productibility of coal seam gas; Coal seam gas no chishitsugakuteki shigen hyoka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, K [University of Shizuoka, Shizuoka (Japan). Faculty of Education

    1996-09-01

    Coal seam gas is also called coal bed methane gas, indicating the gas existing in coal beds. The gas is distinguished from the oil field based gas, and also called non-conventional type gas. Its confirmed reserve is estimated to be 24 trillion m {sup 3}, with the trend of its development seen worldwide as utilization of unused resource. For the necessity of cultivating relevant technologies in Japan, this paper considers processes of production, movement, stockpiling, and accumulation of the gas. Its productibility is controlled by thickness of a coal bed, degree of coalification, gas content, permeability, groundwater flow, and deposition structure. Gas generation potential is evaluated by existing conditions of coal and degree of coalification, and methane production by biological origin and thermal origin. Economically viable methane gas is mainly of the latter origin. Evaluating gas reserve potential requires identification of the whole mechanism of adsorption, accumulation and movement of methane gas. The gas is expected of effect on environmental aspects in addition to availability as utilization of unused energy. 5 figs.

  6. Development of production technology for deep-seated geothermal resources; Shinbu chinetsu shigen seisan gijutsu no kaihatsu gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    Wada, T.; Akazawa, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1997-11-01

    In order to increase the geothermal power generation volume in Japan furthermore after now, it is necessary to develop the deep-seated geothermal fluid collecting technique at 3,000 to 4,000m in depth and about 350degC. In order to collect the deep-seated geothermal resources economically and effectively, there are some principally important problems on production techniques such as P (pressure)-T(temperature)-S (flow rate)-D (fluid density) logging technique, P (pressure)-T (temperature)-C (chemical composition) monitoring technique, high temperature tracer monitoring technique, scale monitoring technique, scale protection and removal technique and so on. The PTSD logging technique is a measuring technique for collecting some data necessary to conduct production management effectively. The PTC monitoring technique is a technique for collecting data on the geothermal resources essential for the resources evaluation and presumption, and tracer monitoring technique is a technique for collecting actual measurement data of fluid flow analysis in the deep-seated geothermal resources. And the sale monitoring is a technique for collecting data on various kinds of scale components of the deep-seated geothermal water and in the steam. In this paper, these techniques are summarized. 8 figs.

  7. NEDO coal resources exploitation subcommittee. 18th project report meeting; NEDO sekitan shigen kaihatsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    In a report on a 'survey for coal transportation system optimization in southern Sumatra' which is to contribute to the improvement of coal exploitation efficiency in the Musi river area in southern Sumatra, the coal transportation system from the coal mine to the harbor is reviewed, scenarios on funding and cost effectiveness and environmental impact are comprehensively examined, and suggestions are submitted for higher efficiency and cost effectiveness. In a report on a 'current utilization status and effectiveness of a non-destructive electromagnetic vibrator shock source,' an electromagnetic vibrator shock source out of several new coal exploration technologies which are combinations of test boring and seismic prospecting is taken up, and is compared, in terms of technical feature and cost effectiveness, with the seismic reflection survey technique that uses an explosive shock source, and then a conclusion is reported that an electromagnetic vibration shock source method is superior. Using the new electromagnetic method, a seismic wave frequency is so chosen as to be suitable for a given depth. Since it is non-destructive and emits less noise, it is expected that it will serve in various fields other than coal mining. (NEDO)

  8. Research Foundation Institute Joint Symposium '97. Ion, marine biotechnology, microgravity, ultrahigh temperature, and laser; Kenkyu kiban shisetsu godo symposium '97. Ion kaiyo bio mujuryoku chokoon laser

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-10

    Presentations were jointly made by NEDO (New Energy and Industrial Technology Development Organization)-financed Ion Engineering Center Corporation, Research Center for the Industrial Utilization of Marine Organisms, Japan Microgravity Center, Japan Ultrahigh Temperature Materials Research Institute, Applied Laser Engineering Center, and organizations annexed to them. The subjects taken up were 'Omnidirectional ion beam technology and titanium ion implantation,' 'Application of ion engineering technology to the prevention of contact allergy,' 'Research on metal/semiconductor transition phase creation for silicon ions,' 'Research on technologies of microalgae-aided CO2 fixation and effective utilization,' 'Construction of gyrB database,' 'Marine microbe-produced antibiotics and assessment of activity,' 'Research on combustion under microgravitational conditions and application to industrial combustors,' 'Research on tube-contained gas/liquid two-phase fluid under microgravitational conditions and application to power generation boiler,' 'Measurement of physical properties of molten semiconductor under microgravitational conditions and research on analysis of heat flow in silicon crystal growing furnace,' 'High temperature oxidation of Mo(Si, Al){sub 2} intermetallic compounds,' 'Development of Nb-based ultrahigh temperature materials,' 'Functional characteristics of Al{sub 2}O{sub 3}/TiC/Ni-based functionally inclined materials,' 'Control of epitaxial crystal growth in CxBE process,' and 'Manufacture of intermetallic compounds by laser plasma hybrid spraying and characteristics.' (NEDO)

  9. Experimental study on the response of very large floating structures (VLFS) in wave; Choogata futaishiki kaiyo kozobutsu no harochu oto ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ota, M; Ikegami, H; Yamaguchi, Y [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-10-01

    The elastic response of VLFS of 1200m long in wave was studied experimentally using a water tank and integral elastic model of 1/80 scale. As offshore airport, a ultra- thin box type floating structure of 5km long, 1km wide and several meter thick is used, and the effect of elasticity is not negligible for such a structure. The experiment used a water tank of 160m long, 30m wide and 3.1m deep. Supposing a water depth of 20m for real VLFSs, the experiment was carried out mainly in a local shallow water area prepared with a temporary bottom together with that in a deep water area. A simple mooring equipment with a linear spring equivalent to real VLFSs was used. The integral floating model was prepared by not mechanical but welded junction to obtain uniform elasticity. The response in wave showed a complicated 3-D behavior, offering useful data for verification of a behavior estimation method. The response was nearly equal between shallow and deep water areas at the same wave length, and the response amplitude in regular waves was equivalent to the significant amplitude in long and short crested irregular waves. 7 refs., 8 figs., 3 tabs.

  10. Management of corrosion control of reinforced concrete in the channel tunnel; Kaiyo tunnel no tekkin concrete no bosyoku kanri to unei

    Energy Technology Data Exchange (ETDEWEB)

    Poubaix, A. [Centre Belge d`Etude de La Corrosion, Bruxelles (Belgium); Cargo, S. [Eurotunnel Operation, Folkstone (United Kingdom)

    1994-12-15

    This paper reports, upon describing the summary of design and construction of Eurotunnel, the contents of the discussions carried out by the Brussels Corrosion Research Center, and their results. Circulating oxygen is supplied sufficiently, and the temperature and humidity are kept high in the tunnel in operation, whereas intermittent dryness may occur locally due to strong air circulation caused by a passing train. While corrosion may occur in any of the reinforcing bars, steel frames, or concrete, the basic corrosion mechanism includes pH decrease in concrete due to its carbonatization, cracking and damage in the concrete, and stray current effect. Detailed discussions were given on experiences of building offshore structures in every part of the world. A possibility of the tunnel getting corroded in 50 to 60 years due to de-passivation in reinforcing bars was indicated against the assumed usable life of 120 years. Therefore, cathodic protection and corrosion monitoring were studied, whereby a unique system was proposed to identify hazardous zones, grasp and analyze data concentratedly. 24 refs., 8 figs., 1 tab.

  11. Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Imai, Y [Hiroshima University, Hiroshima (Japan); Okusu, M [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1997-12-31

    A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

  12. Experimental study on the estimation method of hydrodynamic force acting on floating offshore structures; Futaishiki kaiyo kozobutsu ni kuwawaru ryutairyoku no suiteiho ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, K; Kato, S [Ship Research Inst., Tokyo (Japan); Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1996-04-10

    In the design of various floating offshore structures (FOS), the functionality, safety and amenity of FOSs were examined by estimating responses of FOSs to environmental external forces such as wave, wind and flow. In this paper, the estimation method of drag acting on the whole FOS was established by combining previous study results on hydrodynamic force acting on various bodies such as Reynolds number effect (RNE), 3-D effect (TDE) and interference effect (IE). This hydrodynamic force was also compared with that obtained from the experiment result on a FOS model for TLP to confirm the applicability of this estimation method. The estimation result on the drag coefficient in steady flow by considering RNE, TDE and IE well agreed with experimental one. The drag coefficient acting on FOSs in heaving could be estimated in practically sufficient accuracy by considering drag acting on not columns but only square columns. The estimation result on the drag coefficient acting on FOSs in surging by considering RNE, TDE and IE well agreed with experimental one. 12 refs., 10 figs., 1 tab.

  13. Measures to prevent oil pollution in oceans, and their preservation effect; Kaiyo no abura osen no boshi taisaku to hozen koka ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Shinoda, T; Fukuchi, N; Fujii, H [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sato, S

    1996-04-10

    It was intended to confirm, based on various problems surrounding oil flow-out accidents, that oil fences whose use is first considered when an oil flow-out accident occurs cause oil leakage due to oil pass-through phenomenon as the largest defect in performance of oil fences. Therefore, oil fence performance was analyzed by using a simulation. Furthermore, several types of diffusion prevention and avoidance measures, and combinations thereof were evaluated by using multi-criteria analysis. It was also elucidated how recognitions on the importance of methods to prevent oil pollution differ depending on standpoints. Difference in oil flow-out prevention performance of oil fences due to variation in tidal currents was made clear by combining a diffusion simulation using the finite element method with the prevention performance of oil fences relative to the tidal currents. In areas with no good hydrographic conditions where pollution spreads rapidly, it is necessary to suppress oil diffusion by extending oil fences double or triple, and using gelling agents. 4 refs., 8 figs.

  14. Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Imai, Y. [Hiroshima University, Hiroshima (Japan); Okusu, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1996-12-31

    A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

  15. Research Foundation Institute Joint Symposium '97. Ion, marine biotechnology, microgravity, ultrahigh temperature, and laser; Kenkyu kiban shisetsu godo symposium '97. Ion kaiyo bio mujuryoku chokoon laser

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-10

    Presentations were jointly made by NEDO (New Energy and Industrial Technology Development Organization)-financed Ion Engineering Center Corporation, Research Center for the Industrial Utilization of Marine Organisms, Japan Microgravity Center, Japan Ultrahigh Temperature Materials Research Institute, Applied Laser Engineering Center, and organizations annexed to them. The subjects taken up were 'Omnidirectional ion beam technology and titanium ion implantation,' 'Application of ion engineering technology to the prevention of contact allergy,' 'Research on metal/semiconductor transition phase creation for silicon ions,' 'Research on technologies of microalgae-aided CO2 fixation and effective utilization,' 'Construction of gyrB database,' 'Marine microbe-produced antibiotics and assessment of activity,' 'Research on combustion under microgravitational conditions and application to industrial combustors,' 'Research on tube-contained gas/liquid two-phase fluid under microgravitational conditions and application to power generation boiler,' 'Measurement of physical properties of molten semiconductor under microgravitational conditions and research on analysis of heat flow in silicon crystal growing furnace,' 'High temperature oxidation of Mo(Si, Al){sub 2} intermetallic compounds,' 'Development of Nb-based ultrahigh temperature materials,' 'Functional characteristics of Al{sub 2}O{sub 3}/TiC/Ni-based functionally inclined materials,' 'Control of epitaxial crystal growth in CxBE process,' and 'Manufacture of intermetallic compounds by laser plasma hybrid spraying and characteristics.' (NEDO)

  16. Interactions between wall rocks around magma and hot water. Magma shuhen no hekigan/nessui sogo sayo

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, K.

    1992-12-01

    This paper describes interactions between wall rocks around magma and hot water. The paper discusses effects of hydrothermal environments on dynamic properties of rock minerals with respect to hydrolytic weakening (decrease in dynamic strength of a mineral under presence of water) and reaction enhanced deformation (deformation accelerated by chemical change occurring in a mineral itself). It also explains chemical reactivity of minerals under hydrothermal enviroments with respect to four types of chemical changes in minerals, factors governing mineral dissolution rates, and importance of equilibrium and non-equilibrium in main components in reactions between minerals and waters. These statements quote mainly results of indoor experiments. The paper indicates the following matters as problems to be discussed on interactions between wall rocks around intrusive rocks and hot waters: Deviation from chemical equilibrium in reactions between rocks and waters; change in permeability as a result of reactions between rocks and waters; and possibilities of hydrolytic weakening in rocks around intrusive rock bodies. 52 refs., 6 figs.

  17. Report on a comprehensive research study (home welfare apparatus system - lifestyle); Sogo chosa kenkyu (zaitaku fukushi kiki system - lifestyle) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted on evacuation of aged people at disaster, life maintenance, and welfare apparatus which is applicable to the future change of life style and its harmony with the living environment. In the study of care apparatus, reported were the apparatus operational interface using the indoor environmental control simulation system, safety on moving/transfer equipment, experiment on opening/closing power of sliding doors, study of electric-driven wheel chairs, study of the sitting pressure of various wheel chairs, etc. In relation to the living environment, the paper reported planning of houses introducing care apparatus, assessment of system kitchen, disaster prevention measures for aged/handicapped people, study on performance of the combined use in the living environment, assessment of drops in floor level in the living space, etc. Also reported were assessment on the living environmental control state of serious paralyzers of the limbs, study of a network to support care at home, etc. 48 refs., 117 figs., 29 tabs.

  18. Report on the comprehensive investigational research (at-home welfare apparatus system); Sogo chosa kenkyu (zaitaku fukushi kiki system) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was conducted on the research and development of an at-home welfare apparatus system. In this study, a stay experiment was carried out on whether aged or handicapped people can easily live in welfare houses into which at-home welfare apparatus was integrated, using high-tech at-home nursing apparatus systems (welfare techno house: WTH) which were installed at seven places in Japan based on `the development of a system supporting independent excretion.` In addition, the following were conducted: experiments on at-home welfare apparatus in terms of the evaluation of performance/operability/safety, physical physiology reactions, nursing burden/estimate of independence, two-way communication, examination of housing environments, etc. In WTH Chofu, a test on evaluating welfare apparatus was conducted by people with limbs paralysis and healthy case workers. In WTH Sapporo, by a working group studying biological information, examinations were made on the situation of standing up of healthy adults, old people and people with paralysis of one side of the body from various types of chairs, beds, wheel chairs, portable toilets and sitting down on them. An examination was also made on harmony with psychological function and physically adaptable function by a working group studying at-home nursing apparatus. 75 figs., 15 tabs.

  19. Report on a comprehensive research study (home welfare apparatus system - interface); Sogo chosa kenkyu (zaitaku fukushi kiki system - interface) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the light of the increasing role of welfare at home with the advance of the aging society, the paper conducted an investigational study on the R and D of the home welfare apparatus system - interface. In the study, making the most of the leading home care apparatus systems (welfare technohouses) installed at seven places in the country, the paper carried out a stay experiment on how the life is in the welfare house into which home welfare apparatus is integrated, and an experiment to assess biological data on aged people. Especially as to the support apparatus used for smooth life motions in houses such as movement, excretion and bathing, examined were the linkage with house bodies, care apparatus used, mutual interface with welfare apparatus, etc. By the experiments to assess these home welfare apparatus, an analytical study was conducted on the points to be improved in welfare apparatus and housing equipment, and at the same time on the course of the research/development. Concerning a system for the research study, a research promotion committee was established in Technology Research Association of Medical and Welfare Apparatus, the members of which are learned persons from the industrial circle, the government and universities. 111 figs., 36 tabs.

  20. Report on survey in fiscal 1999. Comprehensive survey on medical appliances; 1999 nendo iryo kiki sogo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The environment around medical treatment in Japan is changing greatly in recent years, because of aging of the population, increase in life habit diseases, and progress in medical science and technologies. In addition, the needs of people are on the trend of diversification. Furthermore, as a result of the information communication field gaining remarkable power, people can obtain information in various forms, and are acquiring chances of learning various kinds of knowledge about medical treatment. Thus, scenes to respond to demands of patients are increasing more than ever in medical activities. On the other hand, works and conversion in providing efficient medical services are sought because of pressures on medical finance. Therefore, the 'medical and welfare device development project' was launched in fiscal 1994, wherein NEDO has been promoting the research and development jointly with private business entities. In fiscal 1999, assignments in important technologies will be made clear taking the future into the sight on three themes in two fields of developing low invasive operation systems, and comprehensively developing artificial organ technologies. Themes to be developed newly in the future will be selected, and the contents of the research and development thereon and the ways it should be will be investigated, evaluated and discussed specifically. (NEDO)

  1. Microalgal biotechnologies for recycling of pollutants; Tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangata sogo saishigenka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, K; Nasu, M; Hashimoto, C; Tanaka, K; Hirata, M [Osaka University, Osaka (Japan). Faculty of Pharmaceutial Science; Fujita, M; Takagi, M [Osaka University, Osaka (Japan). Faculty of Engineering; Hirata, Y; Taya, M [Osaka University, Osaka (Japan). Faculty of Engineering Science; Yamanishi, H [Osaka University, Osaka (Japan). Faculty of Medicine

    1997-02-01

    This paper describes the technology development by which biomass is produced by treatment of pollutants using microalgae, and is recycled. A bioreactor system has been developed, in which microalgal biomass can be obtained through the effective treatment of CO2 and NOx using microalgae having ability of increase under the severe condition with simultaneous flow of CO2 and NOx. A new method has been also developed for separating and recovering the microalgae. Materials, such as glucose, glycerol, acetic acid, and lactic acid, were produced from the obtained biomass through physico-chemical and biological treatments. These materials can be converted into ethanol and hydrogen. For this treatment and recycling system, functions as a part of natural material recycling were considered to be most significant. Development of an analysis and evaluation method of an impact of this system on the natural environment is also tried. 1 fig.

  2. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T.; Hamada, K.; Aoyama, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  3. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T; Hamada, K; Aoyama, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  4. FY 2000 Project of developing international standards for supporting new industries. Standardization of the marine environment analyzers (Analyzers for measuring CO2 in ocean); 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kaiyo kankyo keisoku kiki (kaiyo CO2 sokutei kanren kikirui) no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the research and development of analyzers and analytical procedures necessary for evaluating CO2 abatement effects and fixed quantities in ocean, for proposing the international standards. The program for studying the analytical procedures makes a literature survey mainly on papers and also on patent publications, to collect the data related to this project and establish the database. The program for measuring CO2 in deep ocean studies a suspension type CO2 profiler with a liquid-liquid leveler and develops a small-size, high-precision device serviceable at a depth of 3,000m, around 1m in length and 40kg in weight. The program for flux meters tests various commercial sensors, to obtain the design requirements for the sensor of improved functions to withstand splashes and rolling/pitching. The program for CO2 flux measurement methods study aims at the eddy correlation method, which is the most direct procedure involving limited number of assumptions, after having investigated various procedures, to improve precision of the sensor. (NEDO)

  5. Fiscal 1987 R and D of observation system for probing resources. 3/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper puts together the R and D of a sensor system and a data transmission system in the R and D of observation system for probing resources. In the studies of the on-satellite synthetic-aperture radar (SAR), reexamination was conducted on the basic design of the SAR system and its test plan; also conducted were the drafting of the combination test plan of an SAR/mission transmitter and the design/manufacturing of the machinery required for the test. In the studies of the on-satellite optical sensor, the research of the function/performance of an optical sensor system was carried out, as were the design/manufacturing of an engineering model and the design/model preparation of a visible near infrared radiometer, short-wave infrared radiometer, thermal controller, etc. In the R and D of the data transmission system, a mission recording device was manufactured and tested, with the electrical/mechanical performance confirmed. Further, as a result of the test of the mission transmitter antenna, it was found to fulfill the development specifications. (NEDO)

  6. Achievement report for fiscal 1984 describing research and development of earth resources observation systems; 1984 nendo shigen tansayo kansoku system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    Japan's Outline of Space Development were renewed in February 1984. Under the new principles, the earth resources satellite (ERS-1) program is to be promoted and that research and development efforts for a launch in fiscal 1989 are to be started. Industrial, academic, and governmental organizations concerned making their utmost efforts have established a Technology Research Association for Resources Remote Sensing for the execution of the tasks. The contents of its business are the research and development of an observation system to be installed aboard ERS-1. That is, a synthetic aperture radar and other equipment such as optical sensors and data transmission systems will be developed, and technologies necessary for the development of a satellite borne observation system will be established through evaluation and verification by testing such systems for instance aboard aircraft. Carried out in fiscal 1984 are the studies of required specifications and the drafting of research and development programs for the next and the following fiscal years involving the research and development of the resources exploration system as a whole, sensor systems, and data transmission systems. (NEDO)

  7. Studies on substitutional protein sources for fish meal in the diet of Japanese flounder; Hirame shiryo ni okeru miriyo shigen no riyo

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, K; Furuta, T; Sakaguchi, I [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-08-01

    Effectiveness of livestock industry wastes and vegetable protein added to fish meal in fish farming is tested by feeding the Japanese flounder. In the experiment, a part or the whole of the fish meal protein is replaced by the meat meal (MM), meat and bone meal (MBM), corngluten meal (CGM), or dried silkworm pupa meal (SPM), and fries of the Japanese flounder are fed on the new diets for eight weeks. On a diet containing 60% or less of MM, no change is detected in the fish in terms of increase in weight, protein efficiency ratio, and blood components, indicating that 60% at the highest of fish meal may be replaced by MM. In the case of MBM, it can occupy approximately 20%. As for CGM, the proper substitution rate is approximately 40%. Essential amino acids that the new diets may lack are added for an approximately 10% improvement on the result. The SPM substitution works up to 40%, when, however, the blood components are degraded. The proper substitution rate is therefore placed at approximately 20%. 38 refs., 2 figs., 17 tabs.

  8. Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-08-01

    Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

  9. Fiscal 1998 research achievement report. Research and development for acceleration of biological resource information infrastructure construction; 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To fulfill the above-mentioned purpose, research and development of technologies were carried out involving genetic information measurement, genetic information analysis and utilization, analysis and utilization of information on proteins, and the measurement of biomolecular interaction. In a chapter 'Research and development of genetic information analysis using next-generation genome chip,' gene amplification is effected using RNA-DNA molecules and a method for efficiently building UPD (unilateral protruding DNA) was developed. In a chapter 'Development of international standard DNA chip and analyzing system for analysis of massive gene expression,' a relational database program for activating a system for gene preservation, purification, multiple injection, and management was completed. In a chapter '3D-1D modelling of all the proteins coded on genomes,' this fiscal year, analyses were conducted using Escherichia coli and Bacillus subtilis as model microbes. In a chapter 'Analysis of gene expression clustering,' a software program was developed for measuring and analyzing the budding yeast gene expression profile. (NEDO)

  10. Fiscal 1987 R and D of observation system for probing resources. 2/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper puts together the studies of the system design and control technology and of the system design and evaluation technology concerning the R and D of observation system for probing resources. In the studies of the system design and control technology, conducted were the design/examination on the electrical, mechanical and thermal interfaces between the satellite body and a mission transmitter, as well as the examinations on the mounting position, environmental test conditions, etc., with results produced. Also conducted were the interface with the terrestrial station, operation mission analysis, etc. In the studies of the system design and evaluation technology, for the purpose of evaluating ERS-1 optical sensor specifications, experiments by aircraft were carried out which used on-aircraft imaging spectro radiometer, with evaluation performed by means of multi-channel image data so obtained. Further, in the aircraft/space shuttle experiments, examination was carried out on such items as an aircraft system concerning optical sensors, visible near infrared radiometer, short wave infrared radiometer, and on-satellite synthetic-aperture radar. (NEDO)

  11. Fiscal 1998 research report. Research on energy conversion technology using biomass resources; 1998 nendo chosa hokokusho. Biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Feasibility study was made on construction of the new energy production system by thermochemical conversion or combination of thermochemical and biological conversions of agricultural, fishery and organic waste system biomass resources. This report first outlines types and characteristics of biomass over the world, proposes the classification method of biomass from the viewpoint of biomass energy use, and shows the introduction scenario of biomass energy. The energy potential is calculated of agricultural waste, forestry waste and animal waste as the most promising biomass energy resources, and the biomass energy potential of energy plantation is estimated. The present and future of biochemical energy conversion technologies are viewed. The present and future of thermochemical energy conversion technologies are also viewed. Through evaluation of every conversion technology, the difference in feature between each conversion technology was clarified, and the major issues for further R and D were showed. (NEDO)

  12. Fiscal 1999 geothermal energy development promotion survey. Report on resource assessment for Shiramizugoe area; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Shiramizugoe chiiki shigen hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Under an assumed plan of building a geothermal power station in the Shiramizugoe area of Makizono-cho, Aira-gun, Kagoshima Prefecture, investigations will be conducted under a 4-year program into the amount of geothermal resources, the dimensions and cost performance of a geothermal power station under consideration, and the environmental impact that the locating of such will incur, through for example identifying areas containing geothermal reservoirs suitable for geothermal power generation. In fiscal 1999, activities were conducted in the three fields of (1) survey plan preparation, (2) comprehensive analysis, and (3) environmental assessment. Under item (1), a survey and coordination implementation plan was prepared, existing data were analyzed for the construction of geothermal models out of which a suitable geothermal structure was specified for digging, and a list was drafted of locations for borehole digging for fiscal 2000. Under item (2), it was found that most of the past surveys covered the Ogiri area and that the Shiramizugoe area was but poorly covered. Discussion was made on the geological structure, geothermal structure, geothermal water hydraulic structure, and the geothermal water system. Under item (3), the plan was summarily explained to the local administration, associations of hot spring hotels, and inhabitants in the vicinity, and their consent was obtained. (NEDO)

  13. Report compiled by Research Center for Carbonaceous Resources, Institute for Chemical Reaction Science, Tohoku University; Tohoku Daigaku Hanno Kagaku Kenkyusho tanso shigen hanno kenkyu center hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-04-01

    The Research Center for Carbonaceous Resources was established in April 1991 for the purpose of developing a comprehensive process for converting carbonaceous resources into clean fuels or into materials equipped with advanced functions. In this report, the track records etc. of the center are introduced. Under study in the conversion process research department is the organization of a comprehensive coal conversion process which will be a combination of solvent extraction, catalytic decomposition, and catalytic gasification, whose goal is to convert coal in a clean way at high efficiency. Under study in the conversion catalyst research department are the development of a coal denitrogenation method, development of a low-temperature gasification method by use of inexpensive catalysts, synthesis of C{sub 2} hydrocarbons in a methane/carbon dioxide reaction, etc. Other endeavors under way involve the designing and development of new organic materials such as new carbon materials and a study of the foundation on which such efforts stand, that is, the study of the control of reactions between solids. Furthermore, in the study of interfacial reaction control, the contact gasification of coal, brown coal ion exchange capacity and surface conditions, carbonization of cation exchanged brown coal, etc., are being developed. (NEDO)

  14. Fiscal 1995 verification survey of geothermal exploration technology. Report on a deep geothermal resource survey; 1995 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of reducing the risk of deep geothermal resource development, the paper investigated three factors for the formation of geothermal resource in the deep underground, that is, heat supply from heat source, supply of geothermal fluids, and the developmental status of fracture systems forming reservoir structures. The survey further clarified the status of existence of deep geothermal resource and the whole image of the geothermal system including shallow geothermal energy in order to research/study usability of deep geothermal resource. In the deep geothermal resource survey, drilling/examination were made of a deep geothermal exploration well (`WD-1,` target depth: approximately 3,000-4,000m) in the already developed area, with the aim of making rationalized promotion of the geothermal development. And the status of existence of deep geothermal resource and the whole image of the geothermal system were clarified to investigate/study usability of the geothermal system. In fiscal 1995, `WD-1` in the Kakkonda area reached a depth of 3,729m. By this, surveys were made to grasp the whole image of the shallow-deep geothermal system and to obtain basic data for researching usability of deep geothermal resource. 22 refs., 531 figs., 136 tabs.

  15. FY 1999 basic survey of coal resource development. Coal GIS survey; 1999 nendo sekitan shigen kaihatsu kiso chosa. Sekitan GIS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The purpose of this survey is to construct a comprehensive coal field assessment technology system which can promptly cope with any natural conditions/geological situations of coal field. As to the GIS (geographical information system) which can unifiedly manage/analyze various data being used in other fields, survey was conducted of present situations/technology trends of the resource related GIS, and at the same time the survey is aimed at applying it to the coal resource field. In the survey in this fiscal year, based on the survey made in FY 1998, applicability of GIS function was verified for Australia where the coal GIS is prepared. And the fundamental design was made to construct a coal GIS considered of concrete application in the stage of coal resource exploration and resource assessment. In the fundamental design, prototypes of individual functions of the system were made. Making the analysis using the actual data, expansion and complication of the system size were advanced step by step toward the completion of the system. Such prototypical development method was adopted. (NEDO)

  16. Fiscal 1998 research achievement report. Research and development for acceleration of biological resource information infrastructure construction; 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To fulfill the above-mentioned purpose, research and development of technologies were carried out involving genetic information measurement, genetic information analysis and utilization, analysis and utilization of information on proteins, and the measurement of biomolecular interaction. In a chapter 'Research and development of genetic information analysis using next-generation genome chip,' gene amplification is effected using RNA-DNA molecules and a method for efficiently building UPD (unilateral protruding DNA) was developed. In a chapter 'Development of international standard DNA chip and analyzing system for analysis of massive gene expression,' a relational database program for activating a system for gene preservation, purification, multiple injection, and management was completed. In a chapter '3D-1D modelling of all the proteins coded on genomes,' this fiscal year, analyses were conducted using Escherichia coli and Bacillus subtilis as model microbes. In a chapter 'Analysis of gene expression clustering,' a software program was developed for measuring and analyzing the budding yeast gene expression profile. (NEDO)

  17. Report on the cooperative study of technology to collect valuable resources in brine; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reported on the research, design, and evaluation on a system to recover by sedimentation magnesium from the brine in the salt manufacture by solar evaporation in Mexico, and a system to recover by adsorbent lithium, boron, etc. from the brine of the solar pond salt field in China. In the case of Mexico, an overall recovery system was developed, but in the evaluation of economy of the system, it cannot be said that the system is feasible even if assuming that the required fresh water can be secured. It was found out that the economical efficiency largely depends upon the cost of hydrated lime and the selling price of magnesia clinker. In the case of China, a plant for production of 500 tons/year of lithium carbonate was conceptually designed to evaluate the economical efficiency. As a result, the internal profitability of the plant is not so high, approximately 6%, though continuously profitable during the operation of 15 years. It was indicated that the project was not economically very efficient. 164 figs., 44 tabs.

  18. Fiscal 1998 research report on the total electric power loss reduction project for Myanmer; 1998 nendo Myanmer koku denryoku soshitsu sogo teigen project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of Japanese clean development mechanism, study was made on reduction of greenhouse effect gas emission from thermal power plants by reduction of power transmission and distribution losses of power systems in Myanmer. Study was made on technical power transmission and distribution losses for the national grid transmission system, 33kV sub- transmission system of Thaketa substation in Yangong city, and 6.6kV and 400V distribution systems of Latha and Lanmadaw townships in the downtown area of Yangong. Countermeasures for power loss reduction were considered on the basis of the study result. The loss reduction project plan includes a construction cost of 5,134,000US$, loss reduction of 7,726kW, and loss reduction of 33,213,000kWh. The project feasibility and profitability were evaluated by comparison between a financial internal rate of return (FIRR) and an opportunity cost assuming that a discount rate is the opportunity cost. As a result, FIRR was 17.36% and the discount rate was 8.89% in Myanmer. (NEDO)

  19. Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

  20. New Shinkansen operation management and control systems for Tohoku-Joetsu Shinkansen; Tohoku Joetsu Shinkansen no atarashii Shinkansen sogo system `COSMOS`

    Energy Technology Data Exchange (ETDEWEB)

    Otsuki, K. [East Japan Railway Co., Tokyo (Japan); Koda, K.; Uchimura, T.; Okazaki, S.; Imagawa, T.; Kawaguchi, K. [Hitachi, Ltd., Tokyo (Japan)

    1997-02-01

    Computerized Safety, Maintenance and Operation Systems of Shinkansen (COSMOS) has been developed to properly deal with the diversification and modernization of Shinkansen business and the improvement of its system. To avoid the concentration of duties and loads on any part of the system, the system functions are distributed into eight subsystems, which respectively cover transportation planning, operation management, maintenance work management, power system control, rolling stock management, centralized information management, facilities management, and yard operation management. The COSMOS is a huge system distributed across a large area whose 500 computers and terminals located in the eight subsystems and offices related with Shinkansen are linked by a network. A concept of autonomy and distribution is introduced into the system so that the impact on the others will be kept to the minimum in case some subsystems come to a stop. The new system is excellent in maintainability, flexibility, and extendability, and its operation room is quite compact. The COSMOS has been working smoothly since the beginning of its service, contributing to the modernization of Shinkansen business, such as rapid restoration in case of timetable disturbance, reduction in station workload, improved passenger guidance service, and centralization of section control business. 5 refs., 2 figs.

  1. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Energy Technology Data Exchange (ETDEWEB)

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

    1996-10-28

    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  2. 1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

  3. ESR study on the interaction between carbon blacks and oxygen molecules; ESR ho ni yoru carbon black to sanso bunshi tono sogo sayo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Okazaki, M.; Toriyama, K.; Konishi, Y. [National Industrial Research Institute of Nagoya, Nagoya (Japan)

    2000-02-24

    Interaction between carbon blacks and oxygen molecules has been studied by means of electron spin resonance (ESR) spectroscopy. The ESR spectra of the carbon blacks appears at the g-value of free spin, which are contributed by both isolated electrons and conduction electrons. Upon introducing oxygen to the system the ESR linewidth was broadened in proportion to the partial pressure of oxygen. In case of lampblack (LB 101, Degussa) the interaction was not so strong that it took a tong time at 77K for the linewidth to reach the maxmum value. In case of gassblack (P 140 V, Degussa), on the other hand, the oxygen was easily adsorbed at 298K and the linewidth at 77K became its maximum immediately after cooling. The number of unpaired electrons decreased when the system was kept at 298 K and the decrease was prominent for the local spins. These phenomena have been explained with a simple band model for the electron. (author)

  4. FY 1993-1999 report on all the results of the development of high performance industrial furnace; Koseino kogyoro no kaihatsu sogo seika hokokusho (1993 - 1999 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Since an phenomenon was found out that NOx emission, which was thought to be increased, will be decreased by burning the high temperature preheated air jetting it at high speed (high temperature air combustion) in industrial furnace, there appeared a possibility of technical breakthrough for achieving the heightening of energy utilization efficiency and NOx reduction by exhaust heat recovery at the same time. This project aims at conducting full-scale experiments based on the basement technology including the theoretical elucidation of the combustion mechanism and high temperature air combustion by using various experimental facilities. Further, making full use of the most up-to-date analysis methods and constructing general-purpose database, the development is also aimed at of high performance industrial furnaces such as various heating furnace, heat treat furnace and melting furnace, with the assumption of prompt commercialization of the results of the development. As a result, targets were achieved such as energy saving of 30% or more, downsizing of 20% and a remarkable NOx reduction. Core technologies of this project are in-system limit heat recovery technology, high temperature air combustion technology, temperature field control technology (furnace temperature leveling technology) and high exergy heat transfer technology (furnace temperature heightening technology). (NEDO)

  5. Fiscal 1997 report on the results of the international standardization R and D. Overall survey; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper summed up the results of the survey of tackling with the international standardization by enterprises and organizations involved in the standardization in the U.S., Europe and Japan, the results of the R and D on 20 themes for the international standardization, and the development toward the international standardization. As the R and D themes, the following were selected: the development of chemical method to analyze/evaluate metallic coatings of surface treated steel coating sheets, R and D of the basic evaluation method of functional composite particles, international standards for computer/manikins, basic technology of color image management, study on optimizing design/evaluation technology using quality engineering, study of the international standardization by economic evaluation of environmental impacts, R and D of the standardization of a method to test acceleration life of phosphorous acid fuel cells, development of a test method of halogen-free flame-retardant cables and a study of the cable standards, standard measuring methods of hormone effects of chemical substances, quantification of the sensory evaluation and international standardization in the paint field, experimental study on the international standardization for immunochemical measurement of chemical substances, etc. 24 figs., 16 tabs.

  6. 1998 Annual Study Report. Standardization for compatibility between home information devices; 1998 nendo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Wide-band POF covering Gbps as a Japan-made R and D fruit will be commercialized in the near future. It is very important to make an international standard specification for the transmission by the aid of the wide-band POF, which would be basically the standard for the future home networks. The efforts in this year were directed to finding the optimum parameters for widening the band, for which the necessary characteristics related to, e.g., transmission band and bending loss were measured and evaluated, and the specifications covering a certain range were established. The wide POF system is considered to provide the first chance of the optical transmission systems going into homes on a large scale, and the service conditions and regulations for use in homes have been comprehensively studied. These efforts have begun with collection of the measured data in consideration of operating optical elements represented by LD's, their peripheral circuits and the transmitter/receiver assemblies in which they are mounted at S400 or more. Each of the light emitting and receiving sections, including their peripheral circuits, were measured and evaluated, where they were mainly operated at a short wavelength of 650 nm, which is the same as that for the DVD. (NEDO)

  7. Review of an analysis system of `Long-Term Deep Seafloor Observatory off Muroto Peninsula`; Kochiken Murotomisakioki `kaitei jishin sogo kansoku system` data no kaiseki system no shokai

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, T; Machiyama, H; Hattori, M; Kaneda, Y [Japan Marine Science and Technology Center, Kanagawa (Japan)

    1997-10-22

    Introduced is a data analysis system for Long-Term Deep Seafloor Observatory established off Muroto Point by Japan Marine Science and Technology Center (JAMSTEC), from which observatory data collected by seismograph and tsunami-meter are transmitted real time. JAMSTEC Long-Term Deep Seafloor Observatory Project Team has begun constructing an analysis system for disposing of events in the data and for locating the hypocenter. The analysis system is composed of a data converting unit that converts the forwarded data into the Win format; a data storage/time-dependent data integration unit that keeps the data in a hard disk for a specified period of time, performs disposition and analysis of events in the data, and forwards the data after disposition and analysis to a data recording unit; a data recording unit that stores selected data of seismic events in a recording medium; and a real-time monitor/NTP server unit that displays real time the observed seismic waveform data. 2 figs.

  8. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  9. Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

  10. Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-08-01

    This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

  11. Integrated system technologies for water and sewage works. Information system technologies for rainwater drainage. Jogesuido sogo system gijutsu. Kou joho system

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, T; Nakada, M; Kondo, S [Toshiba Corp., Tokyo (Japan)

    1994-05-01

    The present report introduces the technological trend of rainwater drainage information system mainly with radar rain gauges. The information network must be strengthened as measures against the urban flood from the rainwater drainage. A radar rain gauge-based combination is needed of synthetic and organic processing technologies covering the traveling prediction of rainfall, data communication and rainwater drainage/flooding prediction. The correction method and data communication/display technology are explained for the measurement with radar rain gauges. In both correlation function method and rainfall area pursuit method, the traveling of rainfall is predicted by utilizing the radar information for the sewerage system. For the drainage analysis, it is necessary to quantitatively estimate the rainwater drained into both main and branch sewerage lines. It is made by preparing a rainwater drainage model. The quantitative estimation of rainwater drained into the branch sewerage lines calls for a revised Road Research Laboratory guidance by the Ministry of Construction. Supplemented with knowledge by veteran operators, the displayed image of pump operation support system is simulated for its verification. 2 refs., 3 figs.

  12. Report on achievements in fiscal 1998. Development of a technology to measure biological molecular interactions; 1998 nendo seitai bunshi sogo sayo no keisoku gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It has been indicated possible in principle in recent years to measure biological molecular interactions with the molecules in the living state by combining the technologies called the co-focussing optical system and the fluorescence correlation spectroscopy (FCS). The FCS method is a method capable of analyzing concentrations, sizes, and inter-molecule interactions through detection of fluorescence fluctuation in single molecules in submicron zones. In spite of the FCS method being a very effective method to measure interactions in biological molecules, the technology has not reached a level that allows easy utilization under the present condition. The present research and development is intended to solve the technological problems in the FCS method in the co-focussing optical system, and perform as many research and development works as possible in a short time to establish a technological foundation that can be provided to bio-industrial and medical sites. Particularly, in order to make the utilization thereof possible in measuring biological molecular interactions in cells, a measuring technology using the bi-photon excited fluorescence correlation spectroscopy was established with an objective to reduce damages to cells and their internal micro organs, and minimize effects of interference signals from the own fluorescence. (NEDO)

  13. Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

  14. Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

  15. Interim evaluation report of the mutually operable database systems by different computers; Denshi keisanki sogo un'yo database system chukan hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    This is the interim report on evaluation of the mutually operable database systems by different computers. The techniques for these systems fall into four categories of those related to (1) dispersed data systems, (2) multimedia, (3) high reliability, and (4) elementary techniques for mutually operable network systems. The techniques for the category (1) include those for vertically dispersed databases, database systems for multiple addresses in a wide area, and open type combined database systems, which have been in progress generally as planned. Those for the category (2) include the techniques for color document inputting and information retrieval, meaning compiling, understanding highly overlapping data, and controlling data centered by drawings, which have been in progress generally as planned. Those for the category (3) include the techniques for improving resistance of the networks to obstruction, and security of the data in the networks, which have been in progress generally as planned. Those for the category (4) include the techniques for rule processing for development of protocols, protocols for mutually connecting the systems, and high-speed, high-function networks, which have been in progress generally as planned. It is expected that the original objectives are finally achieved, because the development programs for these categories have been in progress generally as planned. (NEDO)

  16. FY1995 microalgal biotechnology for recycling of pollutants; 1995 nendo tayona sorui kino wo kiban to suru seibutsuken busshitsu junkangta sogo saishigenka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objectives are 1) development of biological processes needed for the treatment of pollutants and the conversion of resulting biomass to value added products such as energy and fine chemicals, and 2) development of techniques for monitoring of both biological and chemical hazards associated with process operation. We developed a microalgal system for simultaneous removal of CO{sub 2}/NO{sub x} from flue gas, as well as an electro-osmotic method for recovery of microalgal cells. A strategy for effective culturing of photoautotrophic cells in photobioreactors was also proposed. We utilized waste algal biomass to produce biosurfactants, and studied about structure-function relationship of lipopeptide biosurfactants. As an energy product, H{sub 2} was produced via lactic acid fermentation of algal biomass. Physiology of marine phytoplankton was also studied in relation to the future mass production of microalgal biomass. A rapid monitoring of microbial populations was possible by using fluorescent probes. An enzyme immunosorbent assay system specific to fish metallothionein was established for the assessment of aquatic environmental pollution. Human herpesvirus latent infection was effectively applied to biological assay of environmental hygiene. (NEDO)

  17. Assessment of a Mega-Float on water quality and ecosystem in Tokyo bay; Choogata futaishiki kaiyo kozobutsu ga Tokyowan no suishitsu to seitaikei ni oyobosu eikyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kyozuka, Y.; Hu, C.; Hasemi, H. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hikai, A.

    1997-08-01

    The effect on the marine environment in the bay when a Mega-Float is installed in a bay was investigated. The physical process such as a residual flow (including tidal currents, water temperature, salt, density, and density currents), and the ecosystem model for which floating organic matter and plankton are handled were incorporated to develop a program for water quality calculation in a bay. The program was used for Tokyo Bay and compared with the conventional calculation result and the oceanograhpic observation result. Simultaneously, the effect on the Mega-Float was considered. On the flow in Tokyo Bay in summer, the calculation result that comparatively coincided with the observation value in a residual flow level was obtained. The horizontal distribution of COD comparatively coincides with the existing observation result. The influence that the Mega-Float exerts on the flow, water temperature, water quality, and ecosystem in the ambient sea area was little and local in the calculation scale (L {times} B {times} d = 6 km {times} 3 km {times} 2 m) of this time. However, the difference occurring due to the design position must also be investigated in future. 12 refs., 8 figs., 5 tabs.

  18. HELIUM, PARTICULATE ORGANIC CARBON and other data from HEIYO, KAIYO and other platforms in the NW Pacific, Philippine Sea and East China Sea from 1939-08-17 to 1988-09-27 (NODC Accession 9000197)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A tape containing part of the annual exchange of chemical data from the Japan Oceanographic Data Center collected from East China Sea (Tung Hai), Philippine Sea, NW...

  19. Determination of sup 238 U in marine organisms by inductively coupled plasma mass spectrometry. Yudo ketsugo plasma shitsuryo bunsekiho ni yoru kaiyo seibutsuchu no sup 238 U no teiryo

    Energy Technology Data Exchange (ETDEWEB)

    Ishii, T.; Nakahara, M; Matsuda, M.; Ishikawa, M. (National Institute of Radiological Sciences, Ibaraki (Japan))

    1991-05-25

    Since the {sup 238} U concentration in seawater is about 3ng/ml at the element level and the activity concentration is 40 {mu} Bq/ml which are considerably higher that those of other {alpha} radioactive materials, it is necessary to study the concentration levels of many marine organisms. After confirming that the inductively coupled plasma mass spectrometry as a new high sensitive analysis for multi-elements is effective to analyze heavy elements such as rare earth elements or uranium, etc., this method was applied to determine {sup 238} U in 55 species of marine organism. The {sup 238} U concentration in soft tissues of marine animal ranged from 0.076 to 5000ng/g wet weight and large difference of concentration was observed depending on the kind of animal and the tissue. Especially, the branchial heart of cephalopod molluscs showed the specific accumulation of {sup 238} U. The concentration factor of branchial heart of Octopus vulgaris which showed the highest value was calculated to be about 10 {sup 3} by comparing it with the concentration of {sup 238} U in Japanese coastal waterseas. The concentration of {sup 238} U in 20 species of algae ranged from 10 to 3700ng/g dry weight. 11 refs., 2 figs., 9 tabs.

  20. Studies on marine ecosystem in particular emphasis on phytoplankton (lecture by the member awarded the oceanographic society of Japan prize for 1992). Shokubutsu plankton wo chushintoshita kaiyo seitaikei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, M. (The University of Tokyo, Tokyo (Japan). Faculty of Science)

    1993-06-25

    This paper, while introducing major study results of the author, summarizes his studies on ecosystems in lakes and oceans with respect mainly to phytoplanktons. The studies include the following subjects: A proposal on mathematical model equations to estimate growth of photosynthetic bacterial populations in deep lake beds; evaluation of stimulative effects for photosynthetic production provided by fertilizer application in lakes, and influences of phytoplanktons on population structures; evaluation on effects imposed on ecosystems from dumping chemical substances, as observed in experimental ecosystems that incorporate part of marine ecosystems; correlation between red-tide life absorbing proliferation stimulating substances and red tide generation; growth of high-concentration phytoplankton populations containing algae as a dominant species in local upwelling environments in oceans; and verification on establishment of specific phytoplankton populations containing pico-phytoplankton as a dominant species in oligotrophic environments in open seas. The paper mentions influences of the author's book, Biological Oceanographic Processes under joint authorship with Parsons on marine ecosystem researchers. 66 refs., 8 figs.

  1. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 1. Resistance, propulsion, advance, and ocean; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 1. Teiko, suishin shindo, kaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following were included: Numerical simulation for submerged body fitted with hydrofoil; Simulation of tandem hydrofoils by finite volume method with moving grid system; Determination of the unknown method surface of planning plates by a formulation based on high aspect ratio approximation; Numerical simulation of a bubble flow by modified density function method, etc. As to floating bodies, Response characteristics of a long life type floating offshore airport in waves (3rd report: Response due to short waves and an attempt of active inclination control); Feasibility design of a floating airport and estimation of environmental forces on it; On the estimation method of hydrodynamic forces acting on a huge floating structure, etc. In addition, A numerical prediction with `DMDF` model of pack ice motion in the Okhotsk Sea; Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Water entry simulation of free-fall lifeboat, etc.

  2. Hydroelastic responses of pontoon type very large floating offshore structures. 2nd Report. Effect of the water depth and the drift forces; Pontoon gata choogata futaishiki kaiyo kozobutsu no harochu chosei oto ni kansuru kenkyu. 2. Senkai eikyo to hyoryuryoku

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, H; Miyajima, S [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Masuda, K; Ikoma, T [Nihon University, Tokyo (Japan). College of Science and Technology

    1997-12-31

    Steady-state drift force in regular waves is theoretically analyzed. It is also studied under combined external force experimentally using a two-dimensional water tank. The fluid forces are analyzed by the pressure distribution method based on the potential theory, in which the effects of water depth are taken into account to discuss the effects of elastic deformation of the floating structure on the drift characteristics of steady-state waves. The tests were carried out using a wave-making circulating water tank equipped with a wind duct to create wind, waves and tidal flow. Drift force under a combined external force by wind, wave and/or tidal flow cannot be accurately predicted by arithmetically adding these components. For predicting drift force by tidal flow, it is necessary to take into account drag force in current at the floating structure bottom as well as that in wind at the front face. Drift force by tidal flow is affected by shallowness of water, which should be taken into account for drag forces. The floating structure will be deformed along the wave face as its stiffness decreases, basically decreasing steady-state drift force. 9 refs., 14 figs.

  3. Hydroelastic responses of pontoon type very large floating offshore structures. 2nd Report. Effect of the water depth and the drift forces; Pontoon gata choogata futaishiki kaiyo kozobutsu no harochu chosei oto ni kansuru kenkyu. 2. Senkai eikyo to hyoryuryoku

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, H.; Miyajima, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Masuda, K.; Ikoma, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-12-31

    Steady-state drift force in regular waves is theoretically analyzed. It is also studied under combined external force experimentally using a two-dimensional water tank. The fluid forces are analyzed by the pressure distribution method based on the potential theory, in which the effects of water depth are taken into account to discuss the effects of elastic deformation of the floating structure on the drift characteristics of steady-state waves. The tests were carried out using a wave-making circulating water tank equipped with a wind duct to create wind, waves and tidal flow. Drift force under a combined external force by wind, wave and/or tidal flow cannot be accurately predicted by arithmetically adding these components. For predicting drift force by tidal flow, it is necessary to take into account drag force in current at the floating structure bottom as well as that in wind at the front face. Drift force by tidal flow is affected by shallowness of water, which should be taken into account for drag forces. The floating structure will be deformed along the wave face as its stiffness decreases, basically decreasing steady-state drift force. 9 refs., 14 figs.

  4. Report on the wind power development field test project in the off-shore park in Daitocho Town in fiscal 1997. System design; 1997 nendo Daitocho kaiyo koen nado ni okeru furyoku kaihatsu field test jigyo hokokusho. System sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This paper reports the wind power development field test project in the off-shore park in Daitocho Town in Shizuoka Prefecture. The annual average wind velocity was 4.2 m/s (at height of 20 m above the ground), where the facility utilization rates for 300 and 500 kW class plants were 15.1 and 16.7%, respectively. Both of the annual average wind velocity and the facility utilization rate do not meet the criteria established by NEDO. Although the location is adjacent to the Natural Park, there is no restricting condition for installation. The substation to which system linkage is to be performed is the Daito substation 3 km north of the planned location. The major load is the Daito Spa in the park facility. Ground bed at depth of 5 m will be used as the windmill foundation supporting bed. There is little electromagnetic wave hazard. The location is 380 m away from the nearest residential house, presenting no windmill noise problem. The amount of power to be generated was assumed 281,000 kWh. Specifications for nine models of 300-kW class windmills that can be introduced into Japan were discussed to select a model. The project cost was calculated to be 128.5 million yen. The construction cost will be 428,000 yen and the power generation cost 38.1 yen/kWh. Its economy is poor when the current unit price for surplus power purchase is considered, but the effect of enlightenment may be expected. (NEDO)

  5. Proceedings of the Spring Meeting of the Society of Naval Architects of Japan (1996). Part 1. Resistance, propulsion, advance, and ocean; Nihon zosen gakkai (1996 nen) shunki koen ronbun maezuri. 1. Teiko, suishin shindo, kaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This is a proceedings of the Spring Meeting of the Society of Naval Architects of Japan made public on May 15 and 16, 1996. In the basic research, the following were included: Numerical simulation for submerged body fitted with hydrofoil; Simulation of tandem hydrofoils by finite volume method with moving grid system; Determination of the unknown method surface of planning plates by a formulation based on high aspect ratio approximation; Numerical simulation of a bubble flow by modified density function method, etc. As to floating bodies, Response characteristics of a long life type floating offshore airport in waves (3rd report: Response due to short waves and an attempt of active inclination control); Feasibility design of a floating airport and estimation of environmental forces on it; On the estimation method of hydrodynamic forces acting on a huge floating structure, etc. In addition, A numerical prediction with `DMDF` model of pack ice motion in the Okhotsk Sea; Development of an observation robot `Flying Fish` for comprehensive measurements of ocean environment; Water entry simulation of free-fall lifeboat, etc.

  6. Marine ecosystem and CO sub 2 fixation. ; Development desired on new fixing technology upon elucidating the mechanisms in the natural world. Kaiyo seitaikei to CO sub 2 kotei. ; Shizenkai no mechanism kaimei ni yoru atarashii kotei gijutsu no kaihatsu wo

    Energy Technology Data Exchange (ETDEWEB)

    Nozaki, K [Electrotechnical Laboratory, Tsukuba (Japan)

    1992-02-15

    This paper describes the following matters on CO{sub 2} fixation using living organisms, and marine organisms in particular. For CO{sub 2} fixation using land organisms, promotion is urged on desert greening and forestation with fast growing trees. The CO{sub 2} transfer into deep sea beds with sea water circulation is a slow process, requiring several hundred to one thousand years before the CO{sub 2} increased in the atmosphere is absorbed into deep sea water. Precipitation of organics produced by photosynthesis of vegetable planktons on the ground surface also contributes to the CO{sub 2} transfer into deeper ground. If the CO{sub 2} fixing speed in coral reefs in Okinawa and Hawaii is applied to the coral reefs all over the world, it will mean a CO{sub 2} fixation being carried out corresponding to an annual increase in the forest area of 10,000 to 200,000 km{sup 2}. The paper touches on technological development to fix CO{sub 2} by propagating vegetable planktons on ocean surface with supply of nutritious salt, or to discard liquefied CO{sub 2} from thermal power plants into deep sea beds. 32 refs., 7 figs., 1 tab.

  7. Biological processing of carbon dioxide. ; Photosynthetic function of plants, and carbon dioxide fixing function of marine organisms. Nisanka tanso no seibutsuteki shori. ; Shokubutsu no kogosei kino to kaiyo seibutsu no nisanka tanso kotei kino

    Energy Technology Data Exchange (ETDEWEB)

    Hirai, M [National Research Inst. for Pollution and Resources, Tsukuba (Japan)

    1991-02-15

    This paper describes photosynthetic function of plants, and CO {sub 2} fixing function of marine organisms. Among the photosythetic reaction systems, the C {sub 3} type reaction carries out CO {sub 2} fixation using the Calvin cycle, and takes out the carbon dioxide out of the system through enzymatic reactions of 3-phosphoglycerate {yields} fructose-6-phosphate. The C {sub 4} type reaction has a special cycle to supply CO {sub 2} to the Calvin cycle, i. e. C {sub 4} dicarboxylic acid cycle. The CAM type reaction enables the photosynthetic type to be converted according to variations in the growing environment. The majority of the surace agricultural crops are from C {sub 3} plants, of which yield may be increased when grown in a high CO {sub 2} atmosphere. On the one hand, gene engineering may make possible breeding of plants having high CO {sub 2} fixing capability. In the area of marine organisms, lime algae growing in clusters around coral reefs form and deposit CaCO {sub 3}. Reef creating corals have symbiotically in their stomach layer brown algae having photosynthetic function to build CaCO {sub 3} skeleton. The corals calcify algae quickly and in a large quantity, hence play an important role in fixing underwater CO {sub 2}. 2 tabs.

  8. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Ocean survey and development of evaluation technology for CO2 sequestration ability); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Assuming the melting and sequestration of CO2 at the intermediate depth of the sea area around Japan, study of evaluation technology of CO2 sequestration ability in ocean was studied, and the FY 1999 results were summed up. In the ocean survey, survey was conducted by ship (No.2 Hakurei-maru) mainly at typical observation points and traverse lines of long. 147 E and long. 155 E. In the survey, the following data were acquired: data on seawater density and chemical tracer, data on release of intermediate-depth/independent buoys, concentration distribution of carbonic acid base substances/nutrient salts/chlorophyll, data on the existing amount of marine organisms and primary production speed measurement experiment, data on experiment on CO2 on-board exposure to organisms in the intermediate depth of ocean, etc. In the measurement/analysis of the sediment particle flux amount, sediment traps were installed/recovered. Further, for the purpose of measuring the neutralizing effect of calcium carbonate, operation test on CaCO{sub 3} melting experimental equipment was conducted in the actual sea area. In the development of a model for evaluation of CO2 sequestration ability, carried out were the improvement of the model using the inverse method, study of the estimated accuracy using the ocean observation data, etc. (NEDO)

  9. FY 2000 report on the results of the R and D of the prediction technology for environmental effects of CO2 ocean sequestration. Ocean survey and development of the assessment technology for capacity of CO2 sequestration; 2000 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Assuming the dissolution/sequestration of CO2 at the medium-depth sea area around Japan (depth: 1,000-2,000m), the development was being proceeded with of the assessment technology for capacity of CO2 ocean sequestration and the prediction technology of environmental effects at the point of CO2 discharge. In FY 2000, conducted were the ocean survey and the development of assessment technology for CO2 sequestration capacity. In the investigational study, the following three were carried out: 1) survey/observation of the flow field on the line of 165 degrees of east longitude, and acquisition of various data such as the distribution of carbonic acid base substances and the speed of carbon transport; 2) study of the amount of existence of organisms and kind/composition of the medium-depth plankton at the typical observation points; 3) test/experiment actually conducted in the sea area for the experimental equipment for CaCO3 dissolution experimental equipment for studying interactions between the CO2 and CaCO3 dissolved into the medium-depth sea. As to the development of the assessment technology, carried out were the heightening of accuracy of medium-depth ocean circulation models using the inverse method already developed and the estimation of the flow field using the observation data. At the same time, the estimation of the flow field, etc. were conducted using large circulation ocean models. (NEDO)

  10. Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. Ocean surveys and development of a technology to evaluate CO2 separation capability; 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO{sub 2} kakuri noryoku hyoka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Assuming that CO2 is dissolved and separated in the middle layer in a sea area around Japan, ocean surveys were carried out to acquire fundamental data required for development of a technology to evaluate CO2 separation capability of ocean, and for development of a technology to forecast environmental effect. In addition, using the western part of the Pacific Ocean as the object, development was performed on a numerical model to forecast behavior of CO2 in ocean in the scale of several ten years to several hundred years, and evaluate capability of CO2 separation from atmosphere. The research and development items for the current fiscal year are as follows: (1) ocean surveys, (2) model development, and (3) surveys and studies required for the ocean surveys and experiments. The survey voyage for item (1) was executed centering on the courses of traverse on 140 degree line of east longitude and 147 degree line of east longitude. The voyage surveyed densities of sea water, such data as chemical tracers, discharged mid-layer neutral buoys, carbonic acid based substances, marine living organisms, and sedimentary particles. For item (2), trial calculations were performed by using an inverse model to estimate structures of ocean flows, and discussions were given to enhance the accuracy. For item (3), design and fabrication were carried out on an equipment to experiment on-site dissolution of calcium carbonate, and a chamber for on-site experiments at deep sea bottom. (NEDO)

  11. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Development of ocean-based artificial deep ocean water (DOW) upwelling devices and researches into enhancement of productivity of surface waters, CO2 fixation and biological effects of DOW; 1998 nendo yojo kaiyo shinsosui shusui system no kaihatsu to kaiyo hiyokuka, nisanka tanso kyushu oyobi seibutsu koka no kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project is implemented for design, fabrication and installation of ocean-based artificial deep ocean water (DOW) upwelling devices which can take DOW at low cost in an ocean; experiments for enhancing productivity of ocean by adding DOW using mesocosms; and studying the biological effects of DOW for keeping freshness of marine products. DOW is successfully taken by the upwelling system from a depth of 800 m in a sea area 2,000 m or more in depth. The system has worked to perform its functions even when attacked by typhoons, which caused wave height of 10 m or more. For enhancing productivity of ocean, the culture experiments are conducted in a small-size, on-shore tank, and the mesocosm experiments in a harbor. The results indicate that addition of DOW increases the phytoplankton phase and its quantity. It is also observed that addition of iron ion further accelerates the fertilizing effect. The results of the experiments conducted in a harbor also indicate that DOW has the fertilizing effect, even in a very small quantity, increasing quantity of small zooplankton. No definite effect of DOW, liquid or ice, is observed for keeping freshness of sliced raw sea bream and bonito. (NEDO)

  12. FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of drilling technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen kussaku gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of developing deep geothermal resources, development of 'drilling technology of deep geothermal resources' was made from FY 1991 to FY 2001, and the results were summarized. As to the development of bits, the bit that can be used for 30 hours or more at a temperature of 250 degrees C was developed, and the demonstrative test was made in FY 1997. Relating to the development of the high temperature use drilling mud, the mud that can be used at a temperature of 350 degrees C was developed, and the test using the actual well was conducted in FY 1997. Concerning the development of the high temperature use cement slurry, the cement slurry with specific gravity of 1.35 or below that can be used under the environment of a temperature of 350 degrees C was developed, and the hanging test of the specimen was made in the actual well in FY 1998. About the development of the high temperature use downhole motor, a prototype of 1/12 scale was fabricated in FY 1998, and the performance test at high temperature was conducted. As to the development of the high temperature use high strength cement slurry, a cement slurry with specific gravity of 1.50 or below and compressive strength of 19.61 MPa that is used under the environment of a temperature of 300 degrees C was developed, and the test on the long-term compressive strength was made in FY 2001. (NEDO)

  13. Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths (Development of technology to produce geothermal resources in great depths); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop geothermal resources, research and development has been performed on the production technologies for the deep-seated geothermal resources, such as pressure, temperature, flow speed and density (PTSD) logging technologies. This paper summarizes the achievements in fiscal 1999. In the actual well test on the developed D-probe, it was verified that the probe operates normally under high temperature environment (342 degrees C) which exceeds the measurement limit of conductive cables (315 degrees C). In developing the PTC monitoring technology, the downhole sampler was improved, and a test was performed in the actual hole in the Hijiori area in Yamagata Prefecture. As a result, collection of hot water of about 900 mL has become possible. In developing the high-temperature tracer monitoring technology, simulation was performed keeping in mind charging the tracer into the Hijiori geothermal area, whereas specifications for charging and collecting the tracer were determined. In developing the scale monitoring technology, experiments were carried out on the fluid systems under deep geothermal conditions by using scale forming devices, by which it was indicated that silica is the important scale constituent. (NEDO)

  14. Results of the supplementary work to the fiscal 1994 New Sunshine Project. Development of geothermal power plants, etc. (development of production, technology for deep-seated geothermal resources); 1994 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant to kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The paper reports on the fiscal 1994 results of the study of the development of a technology for collecting deep-seated geothermal resources, which has been made for increasing the capacity of the geothermal power generation as a part of the New Sunshine Project. As a plan for the development, a development is made of logging equipment and its auxiliary system and then characteristics of the deep-seated geothermal well are clarified. The logging equipment is a PTSD (pressure/temperature/spinner flow-meter/fluid density) logger which stands the use at deep-seated geothermal wells of 400{degree}C and 490 kgf/cm{sup 2} and measures pressure, temperature, flow rate and fluid density under static and dynamic conditions. In this fiscal year, metal seals were developed for preventing geothermal fluids from penetrating into the PT probe. Qualities and inner/outer diameters of various kinds of structural materials used in the S probe were determined, and output necessary enough to detect the rotation number is obtained. Measuring precision of D logging by {gamma} rays was evaluated. The study was made of the monitoring technology including the borehole and ground measuring system, the borehole fluid sampling and the scale formation. Relating to the tracer widely used in monitoring of hydrothermal reservoirs, investigated was the trend of the technology from abroad. 8 refs., 60 figs., 26 tabs.

  15. FY 1998 report on the project for development of hot water utilizing power generating plants and others, supported by New Sunshine Project. Development of extraction technologies and development of production technologies for the deep-seated geothermal resources; 1998 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of the activities for development of extraction and production technologies for the deep-seated geothermal resources, which are expected to contribute to increased geothermal power generation capacity. The program for the PTSD logging technology connects the S probe to PT probe, to simultaneously measure temperature, pressure and volumetric flow, producing the data of good quality even in a high temperature environment over 327 degrees C. Thus, possibility of the commercial system is confirmed. The D probe also produces a density calibration curve showing very good linearity, and operates normally in a high temperature environment of 406 degrees C. The program for the PTC monitoring technology conducts the field tests at Larderello, Italy, to confirm the sampler functions in a high temperature environment. The program for the tracer monitoring technology extracts promising tracers stable at high temperature from those for the liquid, vapor and liquid/vapor mixed phases. Silica is observed to be massively dissolved at 400 to 1,000mg/kg in the fluid under deep geothermal conditions. Scale precipitation rate is minimal for the first 21 days, but increases linearly with time thereafter. The experiments are also conducted for formation and prevention of the Fe-Si-based scales during the flushing period. (NEDO)

  16. FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of production technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen seisan gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For making effective/economical collection of deep geothermal resources, development was made from FY 1991 to FY 2001 of the 'drilling technology for deep geothermal resources' and 'production technology for deep geothermal resources,' and the results were summarized. As to the development of logging technology, the PTSD logging system was developed which can measure temperature/pressure/flow velocity/fluid density in geothermal well under the environment of temperature of 400 degrees C. Concerning the development of monitoring technology, development was made of the PT monitoring system that can make the long-term continuous measuring of temperature/pressure in deep geothermal observation well under the environment of temperature of 400 degrees C and of the C monitoring system that samples geothermal fluids at regular intervals to grasp changes in chemical component. Relating to the development of high temperature tracer monitoring technology, the following were conducted: extraction of high temperature tracer agent that can be used in geothermal reservoirs under the environment of temperature of 300 degrees C, development of simulator, and establishment of how to put tracer agent into the reservoir and how to analyze tracer agent. Further, the R and D were made of scale monitoring technology and scale prevention/removal technology. (NEDO)

  17. Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Development of deep seated geothermal resource collection technologies - development of deep seated geothermal resource production technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu (Shinbu chinetsu shigen seisan gijutu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Items of information about deep seated geothermal resource production technologies were collected, and tests and studies were performed using actual wells. This paper summarizes the achievements in fiscal 2000. In developing the PTDS logging technology, it was verified in the actual well tests that the measured density of a D probe is consistent with the theoretical density, and the accuracy is satisfactory. The extended time measurement at fixed points on temperatures of fluids in the wells, pressures, flow rates, and fluid densities has identified chronological change of the characteristics of the fluids in the wells, including the enthalpy, proving them to be effective in well control. In developing the PTC monitoring technology, a fluid extracting machine for the downhole fluid sampler was fabricated, which has collected hot water successfully in the actual well twice out of seven attempts. In developing the high temperature tracer monitoring technology, experiments were performed using vapor phase and liquid phase tracers, whereas re-discharge of all the tracer materials was identified. In developing the scale preventing and removing technology, a silica recovering device capable of treating hot water at 0.6 ton per hour as maximum was fabricated, and the site tests were performed by using cation-based coagulant. (NEDO)

  18. Report on New Sunshine Program-supported undertakings for fiscal 1995. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Reported are the results of researches conducted in fiscal 1995. For the formulation of a general development design, data are collected about domestic high-temperature thermal wells through questionnaires and literature probing, and are scrutinized. As for the development of logging technology, a memory type PT (Pressure, Temperature) logger is experimentally constructed, and is found to properly operate in an environment of up to 350degC in a production well. An experimentally manufactured S-probe proves to be capable of heat insulation and sealing. In the field of PT monitoring, a high-temperature optical fiber is experimentally fabricated for study, capable of measuring temperatures up to 400degC. As for the development of high-temperature tracer monitoring technology, basic experiments are conducted about the thermal characteristics of aromatic acids, and preparatory experiments about gas phase tracers. In the study of scale monitoring technology, deep-seated fluids are collected and analyzed. In the field of production control, technical problems are discussed and information is gathered centering on methods for scale prevention and removal. 31 refs., 90 figs., 40 tabs.

  19. Report on New Sunshine Program-supported undertakings for fiscal 1997. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu, shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Reported are the results of researches conducted in fiscal 1997. In the field of PTSD (Pressure, Temperature, Spinner flowmeter, fluid Density) well logging, the high-temperature performance of a memory type PT (Pressure, Temperature) well logger is confirmed in a demonstration test. As for the S-probe, modification is effected for the reduction of the outside diameter from 70mm to 56mm, and tests are conducted in real wells. As for the D-probe, a laboratory test is conducted and then the probe behaves as predicted. In the field of PCT (Pressure, Chemical, Temperature) monitoring, the sampler is subjected to an on-site test in Italy, when water is successfully sampled out of the well. In the field of scale monitoring technique, deep-seated fluid is collected and examined, and the scale deposition rate in the deep-seated fluid is determine. For the study of production control technology with respect to scale prevention and removal, an Mg-Si scale synthesis test is conducted in the temperature range of 100-300degC, and it is found that the solubility of scale decreases with a rise in temperature. 19 refs., 93 figs., 24 tabs.

  20. Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

  1. Photovoltaic power generation field test at Industrial Technology Research Institute. Prefectural office building in a sunshine-rich district (Kanagawa Prefectural Industrial Technology Research Institute); Sangyo gijutsu sogo kenkyusho taiyoko hatsuden field test jigyo (nissha ryoko chiku no kenchosha). Kanagawaken sangyo gijutsu sogo kenkyusho

    Energy Technology Data Exchange (ETDEWEB)

    Okazaki, H [Kanagawa Prefectural Government Office, Yokohama (Japan)

    1997-05-30

    The result of a photovoltaic power generation field test in fiscal 1996 on a prefectural office building in a sunshine-rich district is reported. It is a lighting power source installed in fiscal 1994 on the third-floor rooftop of the management information building of Kanagawa Prefectural Industrial Technology Research Institute. It has a capacity of 25kW, operating on system interconnection (no back flow), and has a single 15-series/26-parallel array (mono-crystal modules) facing 38deg westward from due south and inclined at an elevation angle of 20deg. From the 240000kWh insolation that contributed to power generation, a DC power output of 28000kWh was obtained, output of 25000kWh after conversion into AC. The module efficiency was 10.8-13.8%, higher when the daily mean temperature was lower. In the case of 3kW type expected to diffuse into the residential and commercial sector and household sector, one will output 3000kWh a year, which is an appropriate capacity as a locally distributed type power generating system in view of the monthly consumption of 2000kWh by a household in general in the Tokyo Electric Power Co., Ltd. service area. No problem is found in reliability of the tested system. Although the power it generates is less than what this office consumes, it is effective in enlightening people about resources saving and peak cut in summer

  2. Gastroptychus Cavimurus sp. nov., a new Chirostylid (Crustacea, Decapoda, Anomura) from off the western coast of South America

    NARCIS (Netherlands)

    Baba, K.

    1977-01-01

    During the second cruise of the Japanese Research Vessel "Kaiyo Maru" to the western coast of South America in 1968-69, Dr. Osame Tabeta of the Shimonoseki University of Fisheries, then on the staff of the Kyushu University, collected a number of galatheids off the northern Peruvian coast. All of

  3. Confirmation study of the effectiveness of prospect techniques for deep geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1993); 1993 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Drilling and survey of deep geothermal exploration wells were conducted in order to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. Following fiscal 1992, the well was drilled in fiscal 1993 down to depths of 605m-1505m, and a 13-3/8 inch casing was inserted down to a depth of 1500m. In the drilling, four cores including oriented cores were sampled, and microscopic observation, X-ray diffraction analysis, fluid inclusion survey, core property test, etc. were conducted. In the FMI logging, detected were 273 bedding planes, 483 fractures, etc. Further made were a velocity structure survey, a gravity survey in the area of 270 km{sup 2} including deep exploration wells, a quality survey of the Kakkonda river water, etc. As to geothermal structure models in the Kakkonda area, results of the drilling were added to prediction models before drilling deep exploration wells, but the revision was not very much. Besides, studies were made of a survey method using microearthquakes, a survey technique using resistivity, etc. 61 refs., 259 figs., 95 tabs.

  4. Report on 1988 research result on the R and D of observation system for probing resources. 2/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the specialized study in the R and D of the observation system for probing resources. In the interface with the satellite body, the result of the 1986 basic design was reexamined, elucidating the interface conditions, while the telemetry command items were also rechecked, clarifying the restrictions of the operation. In addition, the combination tests of mission equipment were all put together. Reexamined also were the interface specifications of optical sensors. Concerning the interface between the satellite body and the mission transmitter, examination was made on the detailed design level. In the operation mission analysis, algorithm for acquiring mission equipment data was reviewed, as were the operation analysis program and the data acquiring simulation. With a case examined in which an optical sensor satellite image was used for probing oil, the conclusion was obtained that the present design specifications were sufficient. In the experiment of the on-aircraft multi-channel image sensor, the subject sensor was found much higher than before in the performance for identifying rocks/minerals and was expected to be useful for resource probes. Image analysis of the test site was also performed. (NEDO)

  5. Report of a project for the technical development of the environmental preservation and resource effective utilization system in fiscal 1995; 1995 nendo kankyo hozen shigen yuko riyo system gijutsu kaihatsu jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper outlined the present situation of industrial waste all over Japan and the present situation of industrial waste of large urban areas where it is most difficult to secure places for the final disposal, and conducted an analysis on the present and future amount of final disposal waste. According to the literature from the Ministry of Health and Welfare, `research report on the discharge/treatment situation of the industrial waste` and `research results of administrative organizations for industrial waste,` the situation of final disposal from the past to the present was outlined and analyzed to study the future trend. Out of the administrative divisions of Japan, four divisions, which are all typically called large urban areas, were selected, and the situation of industrial waste in large urban areas was outlined and analyzed according to the questionnaire survey and the literature on industrial waste obtained from each administrative division. The survey by the Ministry of Health and Welfare indicated that the volume of the industrial waste discharged from the whole country amounted to approximately 400 million tons in fiscal 1992. However, helped by the improving recycling of waste construction materials, the amount of final disposal around 2000 is presumed to be less by 20% or so than that in 1992. 58 refs., 5 tabs.

  6. FY 1998 report on the verification survey of geothermal exploration technology, etc. 1/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. 1) and 2) were included in this report, and 3) in the next report. In 1), the items were as follows: the study plan/gist of study execution, the details and results of the deep geothermal resource survey, the outline of the deep exploration well drilling work, and the outline of the results of the FY 1998 study. In 2), the drilling work plan/the actual results of the drilling work were summed up. As to the results of the study, summarized were the acquisition of survey data on deep exploration well, heightening of accuracy of the deep geothermal resource exploration method, etc. (NEDO)

  7. Fiscal 2000 report on financially supported geological structure survey overseas. Basic survey for coal resource exploitation (Research on underground probing technology); 2000 nendo kaigai chishitsu kozo chosahi nado hojokin (sekitan shigen kaihatsu kiso chosa) konai tansa gijutsu chosa hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the work of searching for coal beds, comparison is made between the geological structure of the object area, which is predicted, before actual investigation, by a close scrutiny of the result of oceanic pilot boring conducted in the past, result of geophysical exploration, and the geological features of galleries already in presence in the vicinity, and the result obtained from galleries drilled actually for the investigation. The investigation was conducted at the Ikeshima coal mine, Nagasaki Prefecture. In this fiscal year, 5 investigation galleries were drilled, totalling 1640m in length, and, in the mine, geological surveys, survey and measurement, coal quality evaluation, water emergence investigation, boring for coal, etc., were carried out. Comparison was made, and, though in the 2nd Minami No. 06 air duct there was no important difference detected between the prediction and the actual result, some faults were found to exist which had not been predicted by seismic exploration on the ocean. In the 2nd Minami No. 5 air duct, the actual geology was not different from the predicted geology, this endorsing the usefulness of boring for coal. In the 2nd Minami No. 01 gallery, direction and inclination were not greatly different from what had been predicted, but some faults which had not been predicted were discovered. These faults had escaped the scrutiny of neighboring coal beds and pilot boring. (NEDO)

  8. FY 2000 project on the research cooperation for the environmental response type water resource effective utilization system; 2000 nendo kenkyu kyoryoku jigyo. Kankyo taiogata mizu shigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of prevention of water pollution, stable water supply in the Philippines, etc., developmental study was made of a waste water treatment/water recycling system, and the FY 2000 results were summed up. In the operational study of Pilot Plant 1, for the waste water in the papermaking process of used paper recycling plant, development was studied of a waste water treatment/water recycling system. There occurred problems on minuteness, outflow, etc. of anaerobic granules, but those were caused by malfunction of SS removal equipment at plant side. The problems were solved by increasing flocculation/precipitation facilities. As to Pilot Plant 2 of which the R and D are planned to be started in April 2001, the food processing plant was surveyed for study, and SYSCORE was selected. Relating to the waste water treatment test of Pilot Plant 2, researchers of the Industrial Technology Development Institute (ITDI) of the Philippines conducted it under the guidance of the experimental data analysis. Besides, the paper carried out the training for technology spread/acceptance, technology spread seminar, support study in Japan, etc. (NEDO)

  9. Report on fiscal 1999 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies were conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. For the development of techniques for estimating deep-seated geothermal reservoir parameters, the Uenotai district, Akita Prefecture, and the Hatchobaru district, Oita Prefecture, were designated as model fields, and a geothermal system conceptual model was fabricated. Data of the two districts were registered in a database. Using these data, verification was performed of the validity of stochastic estimation techniques, large area flow simulation, rock/water equilibrium reaction simulation, and the like. As for the technique of deep-seated resource amount estimation, a simplified reservoir model was experimentally constructed based on parameters determined by the stochastic estimation of deep-seated reservoirs and on the conceptual model, and a method was studied for TOUGH2-based production prediction. Studies were also made about deep-seated geothermal resource development guidelines, such as exploration guidelines, exploration well boring guidelines, and geothermal fluid production guidelines. (NEDO)

  10. Report on achievements in fiscal 1975 in Sunshine Project. Studies on wide area existence of geothermal resources in great depth; 1975 nendo koiki shinbu chinetsu shigen fuson ni kansuru kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    This paper reports the achievements in the following study items: (1) studies on the AFMT method, (2) observation of heat dissipation by using infrared thermal images, (3) evaluation on the annular topographic pattern in the Hachimantai area identified from the Landsat satellite images, (4) studies on the Tamagawa welded pyroclastic rocks, (5) studies on minerals transformed from the Tamagawa welded pyroclastic rocks, and (6) a method to analyze ground temperature data by using graphic display. Items 2 and 6 in the studies are on the heat balance method, and Item 3 is on remote sensing. Items 4 and 5 were performed as the study on geologic thermometry. In Item 1, a prototype AFMT method exploration device was fabricated, and field experiments were performed in the Onuma area in the Hachimantai wide-area geothermal experiment field. The experiment placed importance on finding problems in transmission and reception of signals from an artificially fluctuating magnetic field, whose result was found greatly contributive to understanding the physical phenomena. However, it was not possible to reach a level to analyze geological structures from the data. In Item 2, simple meteorological observation was performed on ground surface temperature distribution by using an infrared radiation thermometer of remote sensing type. Development was made on a method to measure natural heat dissipation amount from heat balance on the ground surface. (NEDO)

  11. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the evaluation and study of reservoirs and the amount of resources, a reservoir simulation is conducted to grasp the characteristics of reservoirs and the amount of resources. For this purpose, the origin and history of the Kakkonda geothermal field are studied, with special attention paid to the origin of the difference in temperature between the shallow-seated and deep-seated reservoirs, the geometry of granite at Kakkonda, the region of recharge of meteoric water, the distribution of saline concentration in the natural state and the cause of the occurrence, the amount of supply of fluids and heat from the depth to the reservoirs, etc. In the evaluation and study of the economic effectiveness of the exploitation of deep-seated geothermal resources, it is learned that, if a 50MW geothermal power station is to be built at a deep level (drilled depth of 3000m on the average) with a rate of 50% attained in drilling, the steam amount required at such a deep level (presumed to be 75t/h) will be more than twice that required at a shallow level (presumed to be 35/h). (NEDO)

  12. FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This promotion project on the cooperative research aims at developing technology to efficiently extract and recover valuable metals including in large quantity in tailings of ores in the Republic of Kazakhstan in consideration of the environmental harmony. The support study in Japan was conducted as follows. As to the Nikolayevska low grade ore, high leaching speed and high leaching rate by grain refining were made possible. The coarse grain was also possible of leaching if leached for a long time. The sulfide froth is possible of leaching in fine grain and in the temperature range of 50 degrees C. The Zhezkent tailings were possible of leaching with sulfuric acid, by aeration, and in the range of medium temperature. The sulfide froth was possible of leaching in fine grain and at temperature of 50 degrees C. After filtration/washing and regrinding, high sampling rates of bulk concentrate and pyrite concentrate were obtained by sulfide flotation by zanthate. The Zhezkent copper concentrate was tested on various factors such as grain size, temperature, and washing/no washing, to confirm effects of bacteria. In the pre-observation test on Au and Ag leaching, cyanogen leaching test was conducted using Cu leaching residue. About Cu, studied were leaching (vat leaching, flotation froth machine agitation (temperature increase, bacteria)), solvent extraction, and electrowinning. About Au and Ag, studied were cyanogen leaching and process of adsorption of activated carbon. (NEDO)

  13. Fiscal 1997 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1997 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1997, a fumarolic gas test is conducted at the deep-seated geothermal well WD-1b which was drilled in the preceding fiscal year. In the test, chemical and isotopic characteristics are compared between the fluids of the WD-1b and the other existing deep-seated wells, and it is found that the fluids from the WD1b originates in surface water just like the fluids from the others and that the constitution of its gas is not greatly affected by magmatic fluids. A PTS (Pressure, Temperature, Spinner flowmeter) logging is performed to observe conditions in the well with the fluids being discharged and to know the inflow point and rate the fumarolic fluids, and the result is utilized to presume the 3-dimensional stress in the vicinity of the WD-1. An isotopic measurement of water included in the fluids is conducted to examine the origin of the geothermal fluids, constant observation and analysis of micro-earthquakes are carried out, and the fluid flow and fluid hydraulic characteristics are also studied. (NEDO)

  14. FY 1998 report on the verification survey of geothermal exploration technology, etc. 2/2. Survey of deep geothermal resource; 1998 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-01

    For the purpose of commercializing deep geothermal resource, a deep exploration well of 4000m class was drilled in the existing geothermal development area to survey the situation of deep geothermal resource existence and the availability. Concretely, the deep geothermal exploration well was drilled for study in the Kakkonda area, Shizukuishi town, Iwate prefecture, to clarify the situation of deep geothermal resource existence and the whole image of geothermal system. Consideration was made of the deep geothermal exploration method, systematization of deep high temperature drilling technology, and availability of deep geothermal resource. The results of the survey were summed up as follows: 1) general remarks; 2) deep exploration well drilling work; 3) details of the study. This report contained 3). In 3), the items were as follows: heightening of accuracy of the deep geothermal resource exploration method, making of a geothermal model in the Kakkonda area, study of deep drilling technology, study of deep fluid utilization technology, and making of a guide for deep geothermal resource exploration/development in the Kakkonda area. As to the technology of high temperature deep geothermal well drilling, studies were made of the borehole cooling method, mud water cooling method, survey of deterioration of casing with age, etc. (NEDO)

  15. Report on a survey in fiscal 1999. Part 2. Survey on the biomass-derived energy conversion technology; 1999 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Biomass energy is positioned as a promising environment harmonizing energy in the 21st century because it does not break down the CO2 balance in the global scale. The present survey has investigated quantity of biomass resources utilizable as energy resources, investigated and analyzed the biomass-derived energy conversion technology, searched for a promising practically usable technology, and discussed the means to achieve the technological introduction. The foreword chapter describes that now is the good time to recognize importance of and introduce the biomass-derived technology. First and second chapters estimate energy potential and utilizable quantity of wastes-based biomass in Indonesia, Malaysia, the Philippines, and Brazil. Chapter 3 investigates feasibility of methane fermentation and ethanol fermentation as a promising bio-chemical conversion process. Chapter 4 has performed feasibility studies on biomass electric power generation, methanol synthesis by gasification, thermal decomposition and gasification as promising thermo-chemical conversion processes. Chapter 5 proposed a biomass electric power generation system, a biomass-gasified methanol synthesizing system, and a dimethyl ether production system. (NEDO)

  16. Achievement report for fiscal 2000 on international research cooperation project. Research on technologies to decompose heavy hydrocarbon resources; 2000 nendo jushitsu tanka suiso shigen no bunkai gijutsu ni kansuru kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Researches have been made on structuring a hydrocracking process for vacuum distillation residue of Marlim crude oil produced in Brazil (Marlim-VR) being one of the heavy hydrocarbon resources. This paper summarizes the achievements in fiscal 2000. In discussing the hydrocracking conditions, discussions were given on the effects of different iron-based catalysts, reaction pressures, reaction temperatures, effects of solvent addition, and the catalyst made of natural limonite produced in Brazil. As a result, the bottom yield was reduced successfully to 5.5% VR, and conversely oil yield was enhanced up to 84.8% VR by using the limonite produced in Brazil as a catalyst, and by performing bottom recycles under the conditions of 450 degrees C and 10 MPa. In discussing the up-grading of hydrocracking produced oil, a result of 99% by weight or higher was obtained in both of denitration and desulfurization rates. In the fuel evaluation test, a product exceeding 45 being the JIS standard for light oil was derived, which was found a clean product having lower sulfur concentration than the existing heavy oil. (NEDO)

  17. Report on fiscal 2000 survey for geothermal exploration technology verification. Survey of deep-seated geothermal resources; 2000 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    To promote the development of deep-seated geothermal resources in a rationalized way, studies are conducted about deep-seated geothermal resource assessment techniques, development guidelines, and the like. Data were collected at the Sumikawa-Onuma district, Ogiri district, Mori district, Yanaizu-Nishiyama district, and the Onikobe district, and compiled into a database to be open to the public. Studies were made about methods for estimating parameters for deep-seated geothermal reservoirs. The resultant findings indicate that, in the Uenotai and Sumikawa-Onuma districts where geothermal reservoirs are governed mainly by a fracture network, the relaxation method and extrapolation will be effective for deep-seated reservoir temperature estimation, and the ascending current analysis method and extrapolation for permeability estimation. The findings also indicate that the expanse of deep-seated reservoirs will be suitably estimated using a method similar to that applied to shallow-seated reservoirs. In the study of the estimation of the amount of deep-seated geothermal resources, it is concluded that the simplified model A will be effective in dealing with a geothermal district where there is a well-developed fracture network and the simplified model B in dealing with a geothermal district where supply of deep-seated fluid governed by an extensive fault prevails. (NEDO)

  18. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 1/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 1/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In fiscal 1996, the deep-seated exploration well WD-1a is sidetracked for penetration for a target newly assigned at the 3,000m-deep level. Carried out in a survey of well geology are the naked-eye and microscopic observation of core cuttings, X-ray powder method, examination of inclusions in fluids, chemical analysis of whole rocks, analysis of isotopes in minerals, analysis of core fracturing, etc. Also, data are collected from a survey of mud log, survey of water in the well before digging, and from well logging. Furthermore, pressure monitoring etc. are conducted in order to determine the interference in pressure between the deep-seated and shallow-seated wells that accompanies multiple outbursts from the Kakkonda No. 2 machine, to know the water permeability between the shallow-seated and deep-seated parts, and to grasp the anisotropy in permeability in shallow-seated reservoirs. (NEDO)

  19. Improvement of effective utilization technology of wood-based resources and development of their new application fields. Mokushitsukei shigen no yuko riyo gijutsu no kojo to shin prime yoto kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kamiya, F.; Haishi, T.; Sueyoshi, S.; Sotozaki, M.; Kato, A.; Hayashi, Y.; Ito, Y.; Hirabayashi, Y.; Togawa, E.; Obino, T. (Forestry and Forest Products Research Institute, Ibaraki (Japan))

    1991-09-01

    On advanced work and use techniques for wood, the aseismic property of plywood-nailed bearing walls was analyzed by seismic response experiments on an excitor resulting in the sufficient aseismic property beyond usual design specification, and the load deformation model was proposed based on experimental results. The evaluation method of heat insulation for wood houses was also developed, and the simple estimation method of room temperature change and the index for evaluating heat insulation for every structure were proposed. On advanced modification and use techniques for constituents of wooden resources, the chemical structure of saponin in woods was studied together with the relation between the chemical structure and biological activity of unknown saponins synthesized from triterpene. The pervaporation property of organic composite films composed of chitinous substances and cellulose derivatives from natural polymers was also studied to develop pervaporation films effective in separating water from ethyl alcohol. 11 figs., 3 tabs.

  20. Research report for fiscal 1998. Research about feasibility of CO{sub 2} reduction program construction for Pan-Japan sea resources; 1998 nendo chosa hokokusho. Kannihonkai shigen CO{sub 2} sakugen program kochiku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research aims to construct a recyclable resources distribution network in coordination with other Japan Sea countries so as to establish measures for the effective utilization of resources originating in Japan. The research covers the needs in China and in Russia's Far East provinces for used electrical home appliances and the supply capability of Japan's four prefectures on Japan Sea including Akita Prefecture. Demand in the countries on the other side of the sea for three major categories of electrical home appliances (color television sets, washing machines, and refrigerators) for 2010 and 2025 is predicted. Part of the predicted demand is specified to be for used items, and a scenario is built based on the reuse substitution rate. On the other hand, in view of the life time of such commodities and the rate of reusables in the amount of waste generated, a conclusion is reached that probabilities are that all such appliances from the four Japanese prefectures will be put to reuse. When the reuse rate is estimated at 10% for goods under the three major categories from the four prefectures, approximately 20,000 articles out of each of the three categories will be put to reuse, and this will lead to a reduction of CO2 emissions of 7700 tons a year. (NEDO)

  1. Report on 1985 research result on the R and D of observation system for probing resources. 2/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This paper explains the result of R and D of the observation system for probing resources in fiscal 1985. Concerning the interface with the satellite body in the system design and control, the design was clarified for the exclusive use of the interface between an on-satellite synthetic-aperture radar and the satellite body, as were the conditions/specifications of the optical part, detector and signal processor of the sensor system, with the studies conducted for the purpose of switching over to the basic design of the following year without difficulty. Then, an examination was carried out for the basic design level of the interface between the satellite body and the transmitter of the mission. A detailed examination was made for the purpose of smoothing the interface between the mission transmitter of the earth resources satellite ERS-1 and the terrestrial station. In the operation mission analysis, an investigation was made into the efficient operation of on-satellite equipment, with studies made on the conditions and specifications of an on-satellite optical sensor. In the studies of the system design evaluation technology, picture quality of the optical sensor was examined, as were sensor specifications suitable for the probe of oil and other underground resources. In addition, aircraft/space shuttle experiment plans were also examined. (NEDO)

  2. Confirmation study of the effectiveness of prospect techniques for geothermal resources. Deep-seated geothermal resources survey report (Fiscal year 1994); 1994 nendo chinetsu tansa gijutsu nado kensho chosa. Shinbu chinetsu shigen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Drilling and survey of deep geothermal exploration wells were conducted to grasp the existing situation of deep geothermal resource and the whole image of geothermal systems in the area where geothermal resource was already developed. In the drilling work in fiscal 1994, 4000m-class rigs and the top drive system were planned to be used for drilling of 12-1/4 inch wells, but 9-5/8 inch liners were used for drilling down to depths of 2550m or deeper since the amount of lost circulation is large and the withdrawal of devices may be very difficult. And in 8-1/2 inch wells, the well was drilled down to a depth of 2950m. As to the deep resistivity exploration technology using electromagnetic method, studies were made of a multiple-frequency array induction logging (MAIL) method, a vertical electromagnetic profiling (VEMP) method, a joint analysis method, etc. Concerning the synthetic fluid inclusion logging technology, containers were lowered into the well and a comparison was made between data of the homogenization temperature analysis of the formed fluid inclusion and those of the temperature log analysis. With relation to the making of deep geothermal structural models, revision was made according to the determination of depths of Miocene formations, Pre-tertiary formations, and the Kakkonda granite. 65 refs., 268 figs., 79 tabs.

  3. Annual Report (fiscal 1995, No. 10) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (19995 nendo No. 10)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    The report covers Laboratory research activities and a decision that the Laboratory, established in April 1986, will be abolished as scheduled in April 1996. Important coal-related achievements of the Laboratory include the development of a rapid pyrolytic process, studies on coal gasification, propositions for enabling coal to dissolve into general-purpose solvents and for a liquid phase oxidation process, manufacture of advanced-function carbon materials from heavy-weight carbonaceous resources (development of next-generation coke production techniques and of various element techniques for the clean use of coal), etc. As for its activities both domestic and international, the Laboratory, engaged in Education Ministry-financed high-priority scientific research projects, represented the general affairs division in a study titled 'Utilization of various energy resources,' and represented groups participating in other projects titled 'Development of new coal-gasification process' and 'Development of integral conversion process aiming at comprehensive coal utilization.' Furthermore, the Laboratory led the 'Japan-Canada cooperative scientific research relating to the development of technologies for effective coal utilization.' (NEDO)

  4. Report on follow-up for joint research of valuable resources recovery techniques from brackish water; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku follow up hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes follow-up for research and development on the recovery of valuable resources, such as magnesium, bromine and boron, contained in the brackish water for manufacture of common salt in the coastal region of Mexico. For the field survey, salt garden, irrigation plant and manufacturing plant of dinning salt were inspected. The optimum site was examined by assuming desalination plant and solar pond. The groundwater in coastal regions is progressively salified. Since the coastal region is a tourist resort with an round-trip area of whales, environmental protection is indispensable. For the joint research with invited researchers, the solar pond system and fresh water generation were studied. As a result, it was found that the solar pond system is an excellent method for keeping thermal energy in a low cost at the salt garden with abundant solar energy, and that the desalination system combined with distilling is the most suitable method. 7 refs., 8 figs., 1 tab.

  5. FY 1998 achievement report on the R and D for accelerating the basement arrangement of the biological resource information. Bioinformatics; 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu kaihatsu seika hokokusho. Bioinformatics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    The paper described the FY 1998 results of the development of bioinformatics. All structure/sequence known proteins from all public databases were hierarchically classified systematically and according to similarities among sequences. Individual proteins in each classified group were added with explanatory notes of structure and physiological function. The mutually related information in metabolic system/signal transfer system was also included. The state of each residue position was classified into three states in terms of the solvent accessibility and three states in terms of the secondary structure. Parameter sets of occurrence frequency for each state of 20 kinds of amino acid were made. By these, it can be evaluated how much the arbitrary amino acid sequence is suitable for each structure in database. The data on the structure of low molecular-weight compounds are also incorporated so that the search for the related biomolecular system information becomes possible. The metabolic system/signal transfer system information was made database, the link was formed between each protein and each low molecular-weight compound, and the information on biomolecular networks was made searchable. A system to predict/support protein structure and function was developed. (NEDO)

  6. Fiscal 1996 verification and survey of geothermal prospecting technology etc. 2/2. Survey report on deep-seated geothermal resources; 1996 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho. 2/2. Shinbu chinetsu shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of reducing the risk to accompany the exploitation of deep-seated geothermal resources, investigations are conducted into the three factors that govern the formation of geothermal resources at deep levels, that is, the supply of heat from heat sources, the supply of geothermal fluids, and the development of fracture systems contributing to the constitution of reservoir structures. In the study of deep-seated geothermal models for the Kakkonda area, a reservoir structure model, a thermal structure model, and a geothermal fluid/hydraulic structure model are deliberated. Then, after studying the relations of the said three structure models to fracture systems, the boundary between the geothermal fluid convection region and the thermal conduction region near the 3,100m-deep level, the existence of high-salinity fluids and the depth of gas inflow, the ranges of shallow-seated reservoirs and deep-seated reservoirs, the trend of reduction in reservoir pressure and the anisotropy in water permeability in shallow-seated reservoirs, etc., a latest reservoir model is constructed into which all the findings obtained so far are incorporated. As for guidelines for deep-seated thermal resources survey and development, it is so decided that deep-seated geothermal survey guidelines, deep-seated fluid production guidelines, and deep-seated well drilling guidelines be prepared and that assessment be made of their economic effectiveness. (NEDO)

  7. Annual Report (fiscal 1995, No. 10) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (19995 nendo No. 10)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    The report covers Laboratory research activities and a decision that the Laboratory, established in April 1986, will be abolished as scheduled in April 1996. Important coal-related achievements of the Laboratory include the development of a rapid pyrolytic process, studies on coal gasification, propositions for enabling coal to dissolve into general-purpose solvents and for a liquid phase oxidation process, manufacture of advanced-function carbon materials from heavy-weight carbonaceous resources (development of next-generation coke production techniques and of various element techniques for the clean use of coal), etc. As for its activities both domestic and international, the Laboratory, engaged in Education Ministry-financed high-priority scientific research projects, represented the general affairs division in a study titled 'Utilization of various energy resources,' and represented groups participating in other projects titled 'Development of new coal-gasification process' and 'Development of integral conversion process aiming at comprehensive coal utilization.' Furthermore, the Laboratory led the 'Japan-Canada cooperative scientific research relating to the development of technologies for effective coal utilization.' (NEDO)

  8. Fiscal 1993 investigational report on the strengthening of the resource/energy industrial basis of CIS Central Asia (the Republic of Kazakhstan); 1993 nendo CIS Chuo Asia (Kazafusutan kyowakoku) no shigen energy sangyo kiban kyoka ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    The paper grasps the present situation of economy and industry in Kazakhstan and studies a policy for developing the industrial machine manufacturing industry of the country. Since the independence in 1992, the country is now at the great turning point in politics, economy, society and industry. The country is forced to convert from the industrial structure of one local area where much of its own discretion had not been given under the economy system of power centralization to the industrial structure which meets the international economic market system as an independent country. Making good use of agricultural and industrial property in the former U.S.S.R., the country needs to export energy resource like oil, natural gas and coal, and abundant ore resource like iron and non-ferrous metal, which were added with values. As the technical base for it, fostering and strengthening of the industrial machine manufacturing industry is important. At present, the situation is that because of the economic sluggishness, the country cannot manufacture domestically even basic mechanical parts and simply-manufactured parts which are required by the domestic energy industry, machine manufacturing industry, and other industries. The technical program to be proposed by Japan is planned to be worked out later based on the basic research made in fiscal 1993. 6 figs., 14 tabs.

  9. Research report of fiscal 1997. Survey on creation of high-efficiency renewable resources, and bioconversion technology; 1997 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabi ni bioconversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Survey was made on material production technology using creation technology of high-efficiency renewable resources (photosynthesis reaction of plants). Industrially usable plant resources in overseas countries and Japan were arranged, and plant resources unused for food were also surveyed. The present state of genetic engineering necessary for metabolic engineering of higher plants such as fit and high-expression technology of genes, plant cell cultivation, and control technology of plant cell multiplication is described, and elementary technologies required for future gene-recombined plants are predicted. Survey was also made on the trend of creation technology of industrial plants for fat and oil, biodegradable polyester, amino acid, cellulose, fiber (cotton) and forest wood. A patent list on plant biotechnology was prepared, and study on bioconversion of plant resources was also surveyed. Overseas R & D trends on conversion and effective use technologies of renewable bio- resources are reported, and process design and its profitability were evaluated through a case study. 414 refs., 87 figs., 55 tabs.

  10. Fiscal 2000 achievement report on the development of polymeric material from renewable resource using biocatalyst; 2000 nendo seitai shokubai wo riyoshita saisei kano shigen kara no kobunshi sozai no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project aims to develop a biocatalyst-assisted synthesizing method for efficiently manufacturing sugar containing polymers and polylactic acids which generate less environmental impact. The ALP-901 derived from actinomycetes operates best with 5% water content, and remains free of hydrolytic effect even when the rate rises to 20%, and catalyzes transesterification only. The esterification activity of bioprase rose remarkably upon addition of water. A polymer with a molecular weight of scores of thousands was obtained in the polymerization of sugar ester monomers. A sugar undecylenate with a double bond at an end was successfully polymerized. The sugar containing polymer exhibited excellent biodegradability. In a reaction of butanediol and lactide, several types of lactic oligomers different in molecular weight were synthesized. The oligomers were caused to react with divinylcarboxylic acid in the presence of an enzyme, and a polymerizable lactic oligomer was obtained. Furthermore, in a reaction between glucose and lactide, several lactic oligomer derivatives were synthesized, different in molecular weight. In a reaction of the derivatives and divinylcarboxylic acid with an enzyme added thereto, a polymerizable lactic oligomer derivative was obtained, which was brought into polymerization in the presence of a radical polymerization initiator for the production of a high molecular weight gel. (NEDO)

  11. Report on 1988 research result on the R and D of observation system for probing resources. 3/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the specialized study in the R and D of the observation system for probing resources. In the system development of the synthetic-aperture radar (SAR) to be loaded on the earth resources satellite ERS-1, the basic design was reexamined, with an SAR system test carried out. A combination test was performed for SAR and the mission transmitter. The testing device was also improved and manufactured. The optical sensor needs to be a system that uses a wide wavelength area and that is capable of receiving a image data of a high surface resolution; accordingly, on the basis of 1988 results, it was tested by preparing an engineering model (EM). The mission recording device records the observation data of SAR and the optical sensor in an invisible area, reproduces it in a visible area in the ground station, and obtains data. The EM development test implemented in fiscal 1987 was continued for the electronics part and the transport part, with the specifications and interface control documents established simultaneously. Combination tests with the mission transmitter were carried out. Studies were also stated on the antenna part/transmitter part of the mission transmitter. (NEDO)

  12. FY 1995 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1995 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This promotion project on the cooperative research aims to efficiently extract and recover valuable metals (gold, silver, copper, rare metal, etc.) including in large quantity in tailings of ores in the Republic of Kazakhstan. In FY 1995, conducted were the field survey, support study in Japan, acceptance of researchers from Kazakhstan, conceptual design of pilot plant, etc. The ore/mineral for Cu is mainly an alteration ore of chalcopyrite. Au and Ag are low grade and unknown, and the main gangue mineral is pyrite. The low grade ore (waste/much) of the Nikolayevska mine has a tendency to leaching at normal temperature, but the ore of mostly chalcopyrite such as tailings from each place has difficulty in leaching. It gets leaching by increasing temperature. The more the temperature rises, the more conspicuous the reaction becomes. Further, chalcopyrite is leached with priority over pyrite. From the result, a technical potentiality was obtained of leaching of low grade chalcopyrite in tailings mostly of pyrite. The existence of Thiobacillus ferrooxidans was confirmed. As to the recovery method for Au and Ag, CIC is studied. The process of waste/much is solvent extraction, electrowinning study and leaching, and that of tailings is bacteria leaching and leaching study. (NEDO)

  13. Report on 1984 research result on the R and D of observation system for probing resources. 1/2; 1984 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The 'space development policy outline' of Japan was reexamined in February, 1984, which decided on promoting the earth resources satellite (ERS-1) project. Accordingly, the Government Research Institute decided to implement the 'observation system for probing resources' from fiscal 1984. On January 18, 1985, a technological association for resource remote-sensing system was established and entrusted with the 'R and D of observation system for probing resources' from the Institute. This paper is the summary of the research results submitted as the 'report on the results of 1984 assigned research'. The report outlines, first as the 'introduction', the purpose of the establishment of the research association, details of the establishment, organization of the association, development system, development schedule, etc., and summarized, second as the 'general remarks', the explanation of the results of the 1984 assigned research. This explanation included the objectives of the research, the state of the implementation of the research, and the results of the research, for example. The paper contained, thirdly as the 'itemized explanation', the details of the individual explanation of the result for each assigned research subject. (NEDO)

  14. Report on 1987 research result on the R and D of observation system for probing resources. 1/3; 1987 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-07-01

    This paper explains the 1987 results of the R and D of the observation system for probing resources. The system is scheduled to be loaded on the earth resources satellite ERS-1 for which launching in 1991 has been set. On the basis of the results until fiscal 1986, technical examination was made continuously. As to the interface with the satellite body, adjustments were made in technical items with the satellite body concerning electrical, mechanical, thermal and environmental interfaces, for example. In the sensor system, the development specifications and interface specifications were reexamined and revised. In addition, an EM (engineering model) was manufactured for each sub-system of the antenna, transmitter/receiver, and a signal processor comprising the on-satellite synthetic-aperture radar (SAR), with the development test carried out. Each specification was reexamined and revised. On the basis of the basic design of an optical sensor, an EM was manufactured, developed and tested. The related specifications were reexamined and revised. An EM was manufactured for the mission recording device and mission transmitter on the results of the basic design, with the development and the test performed. (NEDO)

  15. FY 2000 report on the results of the survey on the biomass-derived energy conversion technology. III; 2000 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the biomass-derived energy conversion technology which was regarded as promising from the results of the survey already made, the survey was made on the present situation and subjects of the technical development, social needs, energy efficiency, economical efficiency and the future. Studies were conducted on the development of technology for effective biomass utilization and the conceptual design and evaluation of a system for effective biomass utilization. As to the effective biomass utilization technology, the survey was made on the biomass combustion power generation technology/gasification power generation technology, gasification methanol synthesis of biomass, biomass gasification dimethyl ether synthesis, technology of ethanol production by alcohol fermentation via saccharification of biomass, methy-esterification of grease biomass, especially palm oil, and diesel oil production via reformation of by-product glycerin, and energy production from biomass using super- (sub- ) critical reaction. As to the system for effective biomass utilization, the survey was carried out of the regional outline, resource amount and sampling amount, selection of the conversion technology, and economical efficiency of Takatsuki city, Osaka, Shimokawa town, Hokkaido, Yufutsu/Hidaka region, Hokkaido, and Aogaki town, Hyogo. (NEDO)

  16. Annual Report (No. 9, fiscal 1994) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (1994 nendo No.9)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    Research activities at the above institute are reported. In an effort to develop advanced coal utilization techniques aiming at reduction in environmental impact, coals of Canadian origin are investigated in cooperation with Canadian researchers. Outstanding among the achievements are Professor Morio Okazaki's 'Study of manipulation of transfer of heat and substance in porous solid bodies' (winner of prize from The Society of Chemical Engineers, Japan), and Professor Tomoyuki Inui's 'Study of fuel synthesis using porous crystalline catalysts' (winner of prize from The Japan Institute of Energy). Various studies are now under way, which include the development of a technique of high-efficiency pyrolysis for coal etc. at the Research Laboratory of Carbonaceous Resources Conversion Technology; development of a zeolite separation membrane on a ceramic filter at the Hashimoto Laboratory specializing in chemical engineering; measurement of the effect of hydrostatic pressure in active carbon adsorption, research on the state of liquid phase adsorption, etc., at the Okazaki Laboratory; analysis of heated fluid in porous structures by means of the lattice Boltzmann method etc. at the Ogino Laboratory; research on coal liquefaction using iron/sulfur-based catalysts etc. at the Watanabe Laboratory. (NEDO)

  17. FY 1986 annual report on the research and development of observation systems for resources exploitation. 3/4; 1986 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 3/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    Described herein are the FY 1986 results of the research of satellite-borne synthetic aperture radar, as part of the research and development of observation systems for resources exploitation. For the radar antenna, the engineering model is designed and fabricated, and test system is studied, for confirming the electrical functions, and mechanical and electrical interfaces. For the transmitter/receiver, the basic designs of the subsystems and components are drawn, and the models are designed and fabricated for testing serviceability of the high-output amplifiers and long-term stability of the high-stability crystal transmitter/receiver. Their models are also designed and fabricated for confirming their electrical functions, and their electrical, mechanical and thermal interfaces with other systems. For the signal processing section, the interfaces with the intra-SAR, satellite body and mission transmitter are adjusted, and the results are reflected in the related specifications and notes of confirmation. (NEDO)

  18. FY 2000 report on the geothermal development promotion survey - No.C-4 Shiro-mizukoshi area. Resource survey (Primary); 2000 nendo chinetsu kaihatsu sokushin chosa. No. C-4 Shiromizukoshi chiiki shigen chosa hokokusho (Dai 1 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    As a part of the FY 2000 geothermal development promotion survey, survey was conducted in the Shiro-mizukoshi area (about 10km{sup 2}), Kagoshima prefecture, the gradually-inclined area located at the southwest foot of Volcano Kirishima, and the results were summed up. In the survey, the following were carried out: surface survey such as geology/alteration zone/fracture system, high-density gravity exploration, electromagnetic exploration, geochemical fluid survey, core test by drilling three exploration boreholes, temperature log, temperature recovery test, water injection test, short-term jetting test, etc. N12-SZ-1 came across the reservoir associated with the ENE-WSW system fault at a depth of 1,085m. The result of the temperature log and the geochemical temperature indicated that the temperature of the reservoir was between 230 and 240 degrees C. However, the reservoir was regarded as the vapor heating reservoir heated by the high-temperature vapor which is thought to be the shallow ground water separated from the deep reservoir. N12-SZ-2 was a large lost circulation zone at a depth between 1,325 and 1,486m, which indicated that N12-SZ-2 came across the ENE-WSW system Shiro-mizukoshi fault. N12-SZ-3 seems to be the area into which ground water flows. (NEDO)

  19. Report on the FY 1999 international research cooperation project. Development of polymer materials from renewable resources using biocatalyst; 1999 nendo seitai shokubai wo riyoshita saisei kano shigen kara no kobunshi sozai no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted of saccharide polymer using biocatalyst and polylactic acid using biocatalyst. In the R and D of technology to synthesize polymerizing saccharide ester, the use of ALP901 led to success in acquiring hydrophobic polymerizing saccharide ester and saccharide ester with phenol residue. A study was also made of technology to synthesize polymerizing divinyl ester. In the study of the optimization of enzyme reaction conditions, the optimum temperature of ester exchange was 50 degrees C, and also under much higher temperature, 100 degrees C, the enzyme reaction was found to proceed with. In the study of the synthesis of polylactic acid, it was impossible to obtain polymer in the case of using ester lactate. However, in the case of using lactic acid, polymer was acquired at the numerical average molecular weight of approximately 1,200. In the study of the optimization of enzyme reaction conditions, polymer with high molecular weight was acquired at the enzyme amount of 5-10%. It was found out that the conversion rate exceeds 98% in the case of doing the reaction for more than 3 days at the enzyme amount of 5-10%. (NEDO)

  20. Energy and power source mix in East Asia. Restrictions on resource, fund and environment and the future prospect; Higashi Asia no energy dengen mix. Shigen shikin kankyo no seiyaku to kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    In Asian countries, the economic growth rate is extremely higher as compared with the world average, and accordingly a large growth in energy supply/demand and electric power supply/demand is paid attention to. Besides, at users` side, a fear is the worsening of the environmental problem which is brought about by a rapid increase in energy consumption. At suppliers` side, introduction/expansion of a large amount of foreign funds for rapid promotion of power source development become necessary so that supplying facilities catch up with the growth in demand. Moreover, dependence of the supply upon outside the area is becoming higher, and problems in safety guarantee are also becoming prominent. As for energy/power source mix in East Asian countries, the stable supply is basically considered as most important, and economical efficiency is also important including competition conditions among energies and potential raising of investment in supplying facilities. It is no exaggeration to say that the increase in the rate of coal which occupies most of the primary energy supply/power source in East Asian countries depends upon the progress of environmental harmony technology such as clean coal technology. 39 figs., 132 tabs.

  1. Report on fiscal 2000 basic survey for coal resource exploration. Survey for development of new exploration technology (Exploration of shallow layers on the land); 2000 nendo sekitan shigen kaihatsu kiso chosa hokokusho. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    Efforts are made to develop a high-precision high-resolution seismic reflection method, high-efficiency method for measurement in the bored hole, coal potentiality assessment system, and so forth. For the development of the seismic reflection method, studies are conducted to properly deal with a situation where there are high-velocity layers at levels shallower than the object coal bed, and a conclusion is reached that quake generation based on the pseudorandom binary sequence code will be the best for the purpose. The system was tested for verification in a producing coal mine. As for measurement in the bored hole, an on-site test was conducted for a geophysical logging system capable of determining the total sulfur content, ash, and the like, and the system was found to supply high-quality data. In developing the coal potentiality assessment system, studies were made about the basic concept of the coordination of the system with the coal GIS (geographical information system) dealing with spatial data and about the functions of the system, and a conceptual design was prepared. (NEDO)

  2. FY1996 research cooperation for the development of the environmentally friendly technology for highly efficient mineral resources extraction and treatment; 1997 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The above-named project aims to jointly develop technologies to efficiently extract and recover valuable metals (gold, silver, copper, rare metals, etc.) from slag, with caution fully exercised to conserve the environment, for effectively utilizing non-ferrous resources in the Republic of Kazakhstan. The effort covers a seven-year period beginning in fiscal 1994. The elements which are studied are technologies that involve leaching, solvent extraction, electroextraction, recovery of gold and silver, and waste water treatment. In this fiscal year, wet treatment, gold and silver treatment, and waste water treatment are studied in on-site joint researches and in domestic researches for specimens sampled at the Kazakhstan site. In addition, based on the results of the above-said basic researches, some parts of the pilot plant to be constructed is designed and manufactured. For propelling forward the project, equipment necessary for joint research is procured and forwarded to the site, and Kazakhstan scientists are invited to Japan for training. (NEDO)

  3. FY 1986 annual report on the research and development of observation systems for resources exploitation.4/4; 1996 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 4/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    Described herein are the FY 1986 results of the research of satellite-borne optical sensors, and research and development of data transmission systems, as part of the research and development of observation systems for resources exploitation. The research program for the satellite-borne optical sensors involves studies on the design specifications, in order to clarify details of the optical sensor systems and visible to near-infrared ray radiation section. The major parts are fabricated on a trial basis and evaluated, in order to review their specifications, and collect the data necessary for the engineering model designs. The items studied for the short wavelength to infrared ray radiation section include the development specifications, and conditions of the interfaces with the satellite and with the cooler/detector sections, which are to be reflected in the design specifications. The research and development program for the data transmission systems involves basic designs of the mission recorder and examinations thereof, to draw the base lines of the satellite-borne systems. The mission transmitter antenna and electronic circuit sections are investigated in detail. (NEDO)

  4. Survey report for fiscal 1998. Survey of creation of highly efficient renewable resources and bioconversion technologies; 1998 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabini bio conversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey is conducted concerning environmentally friendly industrial technologies that utilize renewable resources, which are technologies of creating highly renewable resources and converting renewable resources by breeding industrial vegetation. In relation with the creation technologies, the state of research and development of basic technologies is surveyed, which involves the fabrication of environmental stress resisting vegetation, studies for the application of the gene expression control mechanism, introduction of multigenes and site-directed genes, etc. Concerning the respective target products expected to be produced by industrial vegetation, as much information as possible relative to genes is collected on the current state of production, metabolism in vegetation and microbials, and biosynthesis. Surveyed in relation with the bioconversion technology are the conversion of vegetation-derived polymers, construction of environmentally friendly ligno-bioprocess, conversion of sugar, production of biofuels, etc. Furthermore, the technology of treating ligneous wastes with supercritical water is surveyed, this to determine the practicality of the technology at the current stage. (NEDO)

  5. Annual Report (No. 9, fiscal 1994) of Research Laboratory of Carbonaceous Resources Conversion Technology, Kyoto University; Kyoto Daigaku Kogakubu jushitsu tanso shigen tenkan kogaku jikken shisetsu nenpo (1994 nendo No.9)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    Research activities at the above institute are reported. In an effort to develop advanced coal utilization techniques aiming at reduction in environmental impact, coals of Canadian origin are investigated in cooperation with Canadian researchers. Outstanding among the achievements are Professor Morio Okazaki's 'Study of manipulation of transfer of heat and substance in porous solid bodies' (winner of prize from The Society of Chemical Engineers, Japan), and Professor Tomoyuki Inui's 'Study of fuel synthesis using porous crystalline catalysts' (winner of prize from The Japan Institute of Energy). Various studies are now under way, which include the development of a technique of high-efficiency pyrolysis for coal etc. at the Research Laboratory of Carbonaceous Resources Conversion Technology; development of a zeolite separation membrane on a ceramic filter at the Hashimoto Laboratory specializing in chemical engineering; measurement of the effect of hydrostatic pressure in active carbon adsorption, research on the state of liquid phase adsorption, etc., at the Okazaki Laboratory; analysis of heated fluid in porous structures by means of the lattice Boltzmann method etc. at the Ogino Laboratory; research on coal liquefaction using iron/sulfur-based catalysts etc. at the Watanabe Laboratory. (NEDO)

  6. Report on 1985 research result on the R and D of observation system for probing resources. 1/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Since fiscal 1984, the technological association for resource remote-sensing system has been entrusted with the 'R and D of observation system for probing resources' from the Government Research Institute and has been carrying out the researches. In 1985, on the basis of the preliminary design implemented in 1984, a design for the exclusive use was worked out for each system, namely, total system, sensor system and data transmission system, towards the development of EM (engineering model) scheduled to start in fiscal 1986, while a trial test was performed simultaneously for the critical components. In addition, in 1985, since the main contractor of the ERS-1 satellite body was decided to be Mitsubishi Electric Co., Ltd. by the National Space Development Agency, a system was established for the purpose of adjusting the wide-ranging interface between the satellite body and the observation system, with a concrete adjusting operation started. In connection with these assigned researches, the intended objectives were mostly achieved through the cooperation by each member of the nine associations, for which the results were summarized in this paper under the contract for research assignment and submitted as the 'report on 1985 results of assigned research'. (NEDO)

  7. Report on the achievements in the Sunshine Project in fiscal 1987. Surveys on coal selection and coal types (Surveys on coal resources for liquefaction); 1987 nendo tanshu sentei chosa tanshu chosa seika hokokusho. Ekikayo sekitan shigen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The survey purpose is to identify availability of coal resources for liquefaction in major coal producing countries in the Pacific basin area. Therefore, collection is carried out on such data as coal existing conditions, coal qualities, production quantities, and infrastructures on coal mines being operated and projects under development or investigation. Coal samples are collected in wide range and exhaustively unbiased to particular coal fields and mines to acquire data to perform selection and evaluation of coals that can be fed to coal liquefying plants. The present survey was intended to acquire fundamental data for the liquefying coal selection, such as coal existing conditions, natures, and infrastructures for the coal resources, taking up as the survey object countries the State of Alaska, U.S.A. and Indonesia. The coal types as the object of the survey are mainly sub-bituminous coal, and additionally brown coal and partly bituminous coal. The amount of coal deposit as the subject of the investigation is 100 million tons or more as the verified reserve. The subject areas cover coal mines in the State of Alaska, U.S.A. (Northern Alaska, Nenana, Beluga, and Matanuska coal fields), and Indonesia (the Sumatra and Kalimantan islands). The survey items are made up of 14 items (see the coal mine survey tables in JN0040851). (NEDO)

  8. FY 1986 annual report on the research and development of observation systems for resources exploitation. 2/4; 1986 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 2/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-07-01

    Described herein are the FY 1986 results of the researches of the system design management and evaluation techniques, as part of the research and development of observation systems for resources exploitation. The research program for the system design management techniques involves clarification of reviewing the conditions of interfaces with, e.g., dimensions, weight and power consumption, in order to make the synthetic aperture radar compatible with the satellite body. The data transmission circuits and ground system parameters are investigated and clarified, for smooth interfaces between the satellite-borne mission transmitter and ground station. The research program for the system design evaluation techniques involves transformation of the optical sensor data into the images, and reviews of the second draft of the optical sensor design specification evaluation, on the premise of the processes in which geological experts visually extract the geological data. The validation methods, data collecting areas, observation devices, data processing systems and the like are also investigated for the aircraft/space shuttle test plans for the resources exploitation observation systems. (NEDO)

  9. FY 1985 annual report on the research and development of observation systems for resources exploitation. 4/4; 1985 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 4/4

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Described herein are the FY 1985 results of the research of satellite-borne optical sensors, and research and development of data transmission systems, as part of the research and development of observation systems for resources exploitation. The research program for the satellite-borne optical sensors involves, e.g., plans for development of the optical sensors borne in ERS-1, and studies on the parts therefor, target specifications of the optical sections, light-collection systems, spectroscopic systems, three-dimensional observation, focus adjustment, alignment adjustment, and temperature control. For the detection systems, the efforts are directed to studies on the visible to near-infrared, and short wavelength to infrared detection and calibration systems, in order to develop the detection sections satisfying the target functions and consistent interfaces with, e.g., the satellite. The research and development program for the data transmission systems involves the major functions, interfaces with the satellite, interfaces with the mission transmitters, thermal interfaces, reliability/quality programs, and development plans, for the mission recorder. (NEDO)

  10. Survey on hydraulic power resources. Survey plan (draft) (For clean energy of the future generations); Chikyu kibo suiryoku shigen chosa chosa keikakusho (an). Mirai no sedai ni clean energy wo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    Promotion of development of hydraulic power and others as fossil fuel alternative energy sources is one of the most important measures for solving the global environmental problems. This draft plan proposes, first of all, to conduct surveys on hydraulic power resources on a global scale, to collect the basic data for development of the energy sources. It is estimated that developed hydraulic power resources account for approximately 14% of the total developable resources, the remainder being left untouched. By region, these percentages rise to approximately 55 and 45% in North America and Europe, respectively. These percentages in Asia, Africa, Latin America and FSU are significantly lower, and their undeveloped resources are estimated to total approximately 6 times as large as those already developed worldwide. It is expected that the hydraulic power resources are surveyed on a 10-year plan (1991 to 2000) with a total budget of 30 billion yen, to collect the data and establish the databases in cooperation with international organizations, e.g., UN organizations, regional organizations (e.g., ASEAN organizations) and newly founded organizations. (NEDO)

  11. Report on 1988 research result on the R and D of observation system for probing resources. 1/3; 1988 nendo shigen tansayo kansoku system no kenkyu kaihatsu. 1/3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-07-01

    This paper explains the 1988 results of the R and D of the observation system for probing resources. The system is scheduled to be loaded on earth resources satellite ERS-1 for which launching in 1991 has been set. On the basis of the results until fiscal 1987, 1988, technical examination was made continuously. As to the interface with the satellite body, the specifications were revised by making adjustment in technical items with the satellite body concerning electrical, mechanical, thermal and environmental interfaces, for example. In the sensor system, the technical specifications until now was reexamined and revised. In addition, an EM (engineering model) which was manufactured based on the basic design, was developed, tested and delivered to the satellite body side. In other words, in the studies of the on-satellite synthetic-aperture radar (SAR), the test device was improved and manufactured, with the EM and SAR system developed and tested. In the optical sensor, the test device was also prepared, with the EM manufactured, developed and tested. In the data transmission system, the specifications were revised by developing and testing an EM for the mission recording device. The mission transmitter was tested with EM and also in combination with other mission equipment. (NEDO)

  12. Research report for fiscal 1998. Research about feasibility of CO{sub 2} reduction program construction for Pan-Japan sea resources; 1998 nendo chosa hokokusho. Kannihonkai shigen CO{sub 2} sakugen program kochiku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research aims to construct a recyclable resources distribution network in coordination with other Japan Sea countries so as to establish measures for the effective utilization of resources originating in Japan. The research covers the needs in China and in Russia's Far East provinces for used electrical home appliances and the supply capability of Japan's four prefectures on Japan Sea including Akita Prefecture. Demand in the countries on the other side of the sea for three major categories of electrical home appliances (color television sets, washing machines, and refrigerators) for 2010 and 2025 is predicted. Part of the predicted demand is specified to be for used items, and a scenario is built based on the reuse substitution rate. On the other hand, in view of the life time of such commodities and the rate of reusables in the amount of waste generated, a conclusion is reached that probabilities are that all such appliances from the four Japanese prefectures will be put to reuse. When the reuse rate is estimated at 10% for goods under the three major categories from the four prefectures, approximately 20,000 articles out of each of the three categories will be put to reuse, and this will lead to a reduction of CO2 emissions of 7700 tons a year. (NEDO)

  13. Report on the results of the Sunshine Project - Verification survey for geothermal exploration technology, etc. Summary. Survey of deep geothermal resource; Chinetsu tansa gijutsu tou kensho chosa. Shinbu chinetsu shigen chosa sokatsu seika hokokusho (Yoyaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    As to the development of deep geothermal resource which is expected to contribute to increasing the capacity of future power generation in Japan, investigational study was made from FY 1992 to FY 2000, and the results were summed up. The investigational study was conducted for the hydrothermal convection type deep geothermal resource with a thermal conducting heating mechanism, of which Kakkonda is typical, including the drilling of deep exploration well using the existing technology. As a result, new information/knowledge were acquired about the thermal structure, reservoir structure and hydrothermal supply structure of the depths, and a deep geothermal model was made. Based on the model, a detailed simulation was made possible, and a whole image of the hydrothermal convection type deep geothermal resource with the thermal conducting heating mechanism was made clear. In the surface survey, observation of microearthquakes, high-accuracy MT method, etc. were carried out, and a grasp of the shape of a new granite body from the surface was made possible. Concerning the drilling technology, the geologic stratum with a temperature over 500 degrees C was successfully drilled down to a depth of 3,729m by prolonging the life of bit at the time of drilling by introducing the top drive system, the closed mud cooling device, etc. (NEDO)

  14. Report on fundamental survey on developing coal resources in fiscal 1999. Survey and development of new exploration technology (exploration of shallow land area beds); 1999 nendo sekitan shigen kaihatsu kiso chosa hokokusho. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the survey and development of new coal exploration technology applied in the NSW State of Australia. It is intended to develop a coal resource assessment method with high accuracy using the reflection method seismic exploration, assisted by other physical exploration methods. The Caroona area has a Permian period ground bed distributed, in which multiple number of coal layers exist. The ground bed is covered with sedimentary layers of the Triassic period inconsistently, and this Triassic period system is covered by volcanic rocks of the Jurassic period inconsistently. Faults are going through the coal beds in their upper or lower layers at locations having soft rock beds. Existence of the faults was estimated by seismic exploration using the two-dimensional reflection method, assisted by the result of the physical logging. The results were unified with the result of test drilling to identify the summary of the latent basset lines. Furthermore, the seismic exploration using the three-dimensional reflective method capable of high-level imaging of underground structures was applied to coal beds existing in depths less than 480 m. Multiple number of local and small-scale sinking were detected with time difference of 5 ms and depth conversion to 7 m. Locations, runs, and inclination were interpreted also on faults having small fall which cannot be detected by the two-dimensional method. The three-dimensional method was found capable of identifying micro structural changes and fault runs that cannot be tracked by the two-dimensional method. (NEDO)

  15. Design of environment-friendly and next generation-type conversion system for unused carbon resources by developing highly functional materials; Kokino zairyo kaihatsu ni yoru kankyo chowagata jisedai miriyo tanso shigen tenkan system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Wakabayashi, K; Morooka, S; Arai, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Sakanishi, K [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

    1997-02-01

    Studies are conducted for the development of now-unused kinds of fossil carbon resources, such as low rank coal and heavy gravity crude oil, into higher-value liquid fuel. In the preliminary treatment process, the fossil carbon resources are dried by use of supercritical carbon dioxide, when it is found that the resources are disintegrated and water is desorbed. In a low rank coal liquefaction process using the NiMo/KB (Kefjen Black) catalyst, more than 60% is converted into oil, which rate is improved by use of the dual-temperature liquefaction process. This catalyst may be recovered by separation utilizing specific gravity difference. As a low temperature gasification catalyst, the alkaline carbonate-carried carbon catalyst is very quick at the initial stage of reaction. The perovskite-carried alkaline carbonate catalyst is high in carbon oxidizing/activating efficiency at low temperatures. The silica film deposited on an alumina-coated support tube is excellent in selectivity and speed as a hydrogen separating film, and a carbonized polyimide film as a carbon dioxide separating film. For the supercritical phase adsorption/separation of chemicals not to be distilled easily, the NaY-type zeolite functions effectively. Pd/ZrO2 serving as a carbon monoxide conversion catalyst enables the recovery of more MeOH when Pd grains are smaller in diameter.

  16. Fiscal 1999 basic survey report for promotion of joint implementation. Project for overall loss reduction in Myanmar for thermoelectric power during transmission and distribution; 1999 nendo Myanmar koku karyoku sohaiden denryoku sonshitsu sogo teigen project hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With connection to the clean development mechanism (CDM) taken into consideration, a study is made about achieving greenhouse gas reduction in Myanmar through power generation facility heat efficiency improvement and power loss reduction. Taken up in the study are the Shwedaung power plant, the Mann power plant, and the power transmission system in the Mandalay District. The profitability of thermoelectric power facility improvement is calculated using the financial internal rate of return (FIRR), derivable from the cost of thermoelectric power facility improvement and the convenience to be created thereby, and using the opportunity cost in Myanmar. The result is then subjected to a feasibility study. Most effective for CO2 reduction is the addition or installation of advanced compound cycle power generation facilities which are also excellent in heat efficiency and power generation cost. The FIRR of thermoelectric power facility improvement is 9.4-12.8%, which means the effort is worth investment. Measures for decreasing power loss during transmission include the use of higher voltages, laying of new lines, employment of conductors thicker in size, and the installation of phase modifiers. The economic internal rate of return (EIRR) and FIRR are calculated for the study of feasibility. An analysis covering a 10-year period results in a 20.41% EIRR (exceeding the socially accepted discount rate of 10%) and a 17.56% FIRR (exceeding the general loan interest of 15%), which means that there is feasibility. (NEDO)

  17. General evaluation survey report on fiscal 1998 investigation of geothermal development and promotion. No.C-3 Akinomiya area (Third); 1998 nendo chinetsu kaihatsu sokushin chosa sogo hyoka chosa hokokusho. No.C-3. Akinomiya chiiki (dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    With Akinomiya area (11.4 km{sup 2}) selected in Akita prefecture as the survey C area in fiscal 1996, the first survey was conducted. This paper is a summary of memorandum from an advisory standpoint on the evaluation survey concerning the fiscal 1998 investigation results. The contents of the survey are geological investigation, precision gravity exploration, soil gas investigation, electromagnetic exploration, fluid chemical investigation, well drilling and short-term eruption test. An alteration zone was recognized around the place where clay minerals used to be mined, with the center of the zone situated 500-600 m east of a fault. The alteration condition of Akinomiya area seems to be different from that of Doroyu Wasabisawa area. The supplementary gravity survey was carried out at total 58 points in fiscal 1998. It is desirable to set supplementary measuring points over a wide surrounding area for a depth structure analysis. Also performed was a study of mercury concentration in the soil gas. While CSAMT and TDEM methods were employed for the electromagnetic exploration, a suitable method should be carefully selected for a wide area high-density exploration. Consistency with adjacent areas is essential in preparing investigation items particularly for a geothermal model. (NEDO)

  18. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  19. FY 1998 report on the comprehensive analysis in the geothermal development promotion survey. Tertiary. No.C-3 Akinomiya area; 1998 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-3 Akinomiya chiiki (Dai 3 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    The geothermal development promotion survey was conducted in the Akinomiya area, Ogachi county, Akita prefecture, and the FY 1998 results were summed up. In the surface survey, geology/electromagnetism/precision gravity survey was made as supplementary survey, and re-analysis of 3D models was made. In the well survey, three wells of N10-AY-6 to N10-AY-8 were drilled to conduct the core examination, temperature/pressure logging, sampler logging, short-term jetting test, etc. Also conducted were the reservoir evaluation, environmental effect survey, etc. by pressure monitoring and water level observation. The results of the comprehensive analysis predict the following. In the Akinomiya area, there exists heat source in deep parts around Mt. Yamabushi-dake and Mt. Takamatsu-dake; Being given heat from this heat source, rocks, ground water and volcanic gas react on each other to form geothermal fluids. It is presumed that high temperature geothermal reservoirs exist in the east of the area. Moreover, the pressure distribution indicates that the Akinomiya reservoir and Wasabizawa reservoir can be a chain hydraulically. On the other hand, the west of the area is the low temperature and heat conductive area, and therefore, there seem to be no high temperature fluids there. (NEDO)

  20. FY 2000 Research and development of technology for medical and welfare equipment. Report on the comprehensive survey on welfare equipment; 2000 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu chosa hokokusho. Fukushi kiki sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The survey is conducted on the advanced basic and application technologies for medical and welfare equipment, e.g., biotechnology and drug delivery systems, to promote development of these technologies. For development of the gene-aided diagnostic system equipment for clinical purposes, surveys are conducted on current medical equipment and related technologies, and the results are summarized and pigeonholed for each equipment type. Also summarized are the small- to medium-sized enterprises which are considered to have techniques needed for development of sensors for heart disease treatment systems. For usability of welfare-related equipment products, investigations are made viewed from the designs oriented to human adaptability, human adaptable designs in the aging societies, and welfare-related problems in the aging societies and usability. The latest information on leading organizations and researchers is collected, for continuation and development of the usability programs for welfare-related equipment products, and also for inviting the current related technologies and researchers on life supporting for the aged in Japan to the programs. (NEDO)

  1. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  2. FY 1998 annual summary report on comprehensive development study of high-function flat panel display techniques (second year); 1998 nendo koseino flat panel display gijutsu no sogo kaihatsu kenkyu seika hokokusho. Daininendo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is aimed at creation of the new world display industry in Shikoku by developing the high-function flat panel display techniques and thereby establishing new techniques which solve the problems involved in, e.g., LEDs, plasma-aided devices and ELs other than liquid crystal devices. For development of emitters using diamond, important results have been obtained for the morphology, and cathode luminescence, Raman and photoluminescence spectra of polycrystalline diamond, synthesized by the vapor-phase process under varying conditions, on the electron radiation characteristics of the emitters. These results have led to clarification of the optimum vapor-phase synthesis conditions for diamond for high-function emitters. The techniques utilizing focused ion beams have also advanced to develop thin polycrystalline diamond films for emitters which correspond to the image elements of quality for television. For electron emitters, a structure prepared by implantation without using a high electrical field is proposed, and the device mechanisms involved are clarified. (NEDO)

  3. Overall analysis report on the fiscal 1994 geothermal development promotion survey. No.C-2. Wasabizawa area (secondary); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-2. Wasabizawa chiiki (dainiji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    The Wasabizawa area is located near the boundary between Yuzawa city south of Akita pref. and Ogachi-machi, Ogachi-gun, Akita pref, having a range of 3.0km northeast-southwest and 2.5km northwest-southeast of Wasabizawa almost as a center. The area for survey and its circumference are national forests, and the east and a part of the south of the area are designated as the Kurikoma quasi-national park third type special region. From the geochemical temperature distribution, it can be assumed that geothermal fluids of around 300{degree}C exist in the deep underground of the Kaminotai-Wasabizawa-Akinomiya area. From the distribution of density basements, the block structure of the basement can be estimated. Around the boundary of the ridge/sedimentation region of this density basement, fractures develop and the formation of reservoir structure is expected from the comparison with the result of the well survey. In the blowout test, obtained were 284.3{degree}C and 83.05 kgf/cm{sup 2} at a depth of 1,300m. In the geothermal system, it is assumed that reservoir structures of geothermal fluids develop in the deep underground of the central part of the area. The heat source to the geothermal system is supposed to be the magma reservoir remaining in Takamatsudake volcanic rocks. 110 refs., 177 figs., 105 tabs.

  4. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for securement of interconnection between intelligent home electric appliances; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Johokadenkiki kan no sogo setsuzokusei kakuho no tameno hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development had been under way since fiscal 1998 for working out propositions relating to the international standardization of connection interface systems for digital AV (audio-visual) equipment. This report outlines the result of the project in its fiscal last year. The link working group (WG) actually built a transceiver at 5 mm pitch in its second trial, measured and evaluated its behavior under high-temperature and high-humidity circumstances, and acquired numerical data for interface specifications. The connection interface WG in its second trial fabricated a tiny optical connector for POF (plastic optical fiber) and evaluated its resistance to environment. As the result, sufficient resistance to environment was detected in the connector, and then a proposition was presented to IEC/TC86 that the connector be standardized as an optical connector for intelligent home electric appliances. The POF optimization WG performed an environment resistant test for POF, similar to those for transceivers and connectors, and then recognized that POF of the GI type was low in transmission loss and that it stably retained its wide-band feature. (NEDO)

  5. FY 1992 Report on results of the research and development of the technologies for creating/processing advanced biomaterials. Part 2; 1992 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 2. Sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  6. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area; 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    As part of the geothermal development promotion survey, the comprehensive analysis was made on the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was conducted in FY 1999. In the evaluation of reservoirs, the following were carried out: comprehensive analysis of various data on the surface survey, well exploration, etc., which were stored in surveys from the primary to the forth, modification/construction of geothermal system models, numerical simulation using 3D models, etc. In the long-term jetting test, production/reduction tests were conducted using N9-AY-3 and N10-AY-8 as production wells and N8-AY-1 and N10-AY-6 as reduction wells. The results of the comprehensive analysis were outlined as follows. The distribution of high temperature zones promising as areas for geothermal development was grasped. The distribution of the main fracture structure underground was grasped. A total amount of 124t/h steam was confirmed by short/long term jetting tests. In the simulation of prediction of production, the result was obtained that there was potential power generation of 30MW in the Akinomiya area alone and 60MW both in the Akinomiya area and the Wasabizawa area. (NEDO)

  7. Study of dependence of DC output of rectenna array on the method of inter-connection of its array element; Rectenna array chokuryu shutsuryoku no array yoso sogo setsuzokuho izonsei no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, M.; Matsumoto, H. [Kyoto University, Kyoto (Japan). Radio Atmospheric Science Center

    1997-08-20

    In 1994 and 1995, a ground-to-ground microwave power transmission (MPT) experiment was carried out by a group of Kyoto University, Kobe University and Kansai Electric Power Company. Among the MPT technologies, which are one of the most important key issues for the realization of the Solar Power Satellite (SPS), studies of `rectenna` (rectifying antenna) have been pursued to archive higher efficiency of conversion from microwave to DC. We had developed a new rectenna panel which can effectively rectify a microwave power of 2.5 W at 2.45 GHz before the ground-to ground MPT field experiment. We examine the sum of the outputs of two or three rectenna panels in which are connected ether in parallel or in series or in the hybrid connection under the same microwave circumstances. The experiment leads us to conclude: (1) The sum of the DC outputs from two rectenna panels connected in parallel is larger than that from those connected in series. (2) The sum of the DC outputs of two rectenna panels is generally smaller than the sum of the DC output of the individual panels unless their output is equal to each other. (3) The total output DC power of a rectenna array increases when we connect the array element with consideration of the `element balance`. Based on the experiment, we propose an optimum method for connection of individual rectenna elements to form an rectenna array. 12 refs., 9 figs., 4 tabs.

  8. 1998 Annual Study Report. Standardization for securing interoperability between optical disk systems; 1998 nendo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D program is aimed at securing interoperability between optical disk systems, based on the logical formats, to propose the draft international standards. For the volume/file structures proposed by ISO/IEC 13346, the universal disk format (UDF) proposed by the Optical Storage Technology Association (OSTA) is taken as the target file system, to improve the conformance test environments and develop the standards for advanced interoperability. The 1998 R and D themes include development of the UDF conformance testing tools for avoiding the interoperability-related problems involved in the UDF, which are actually observed, and investigations on the UAF specifications and preparation of the UAF-related standard evaluation systems for preparation of the draft standards for the Universal Accessible Filesystem (UAF), planned to be conducted in and after the next fiscal year, which allows, e.g., network seamless application of a variety of the future optical disks. (NEDO)

  9. NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

  10. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  11. Estimation of water-coal surface interaction during heat treatment of coal by use of FTir and DSC; FTir to DSC wo mochiita sekitan-mizu kan sogo sayo no teiryoteki hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Mae, K.; Morozumi, F.; Kusakawa, T. [Kyoto University, Kyoto (Japan)

    1997-10-30

    The authors have recently presented a method to estimate the strength distribution of hydrogen bondings in coal using FTir and DSC. The method was applied to estimate the strength of coal-water interaction in two different coals and to estimate the enthalpy change deriving from the change in hydrogen bondings during the desorption of water. The estimated enthalpy change was compared with the total enthalpy change estimated by DSC measurement to examine the importance of hydrogen bondings during the desertion of water. 1 ref., 6 figs.

  12. FY 1999 Report on the technical results. Research and development project for creation of the quick-effect type international standards (Comprehensive surveys); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Safety, environment protection and internationality are most important product qualities, and international standardization of product qualities and testing methods are essential for strengthening international competitiveness. Viewed from this angle, the R and D project is conducted to propose the international standards for the following 5 areas related to environment and safety, selected in expectation that the results could be obtained in short time for preparation of the international proposals; (1) standardization of the wireless IC tags for logistics management, (2) standardization of quality and testing methods of automobile fuels and lubricants, (3) research and development for international standards in the field of safety of machinery, (4) standardization of evaluation methods for electronic data security system, and (5) standardization for the safety of light emitting diodes. The results are obtained for preparation of the international standard drafts, interim or final. The activities are directed to promotion of international interchangeability of radio frequency identification (RFID) systems for area (1); to standardization of the systems for emergency stopping/controlling machines for the area (3), to improvement of security evaluation standards of existing information systems for the area (4), and to unification of the ISO/IEC safety standards for the area (5). (NEDO)

  13. Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

  14. Evaluation report on research and development of a database system for mutual computer operation; Denshi keisanki sogo un'yo database system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This paper describes evaluation on the research and development of a database system for mutual computer operation, with respect to discrete database technology, multi-media technology, high reliability technology, and mutual operation network system technology. A large number of research results placing the views on the future were derived, such as the issues of discretion and utilization patterns of the discrete database, structuring of data for multi-media information, retrieval systems, flexible and high-level utilization of the network, and the issues in database protection. These achievements are publicly disclosed widely. The largest feature of this project is in aiming at forming a network system that can be operated mutually under multi-vender environment. Therefore, the researches and developments have been executed under the spirit of the principle of openness to public and international cooperation. These efforts are represented by organizing the rule establishment committee, execution of mutual interconnection experiment (including demonstration evaluation), and development of the mounting rules based on the ISO's 'open system interconnection (OSI)'. These results are compiled in the JIS as the basic reference model for the open system interconnection, whereas the targets shown in the basic plan have been achieved sufficiently. (NEDO)

  15. Fiscal 1993-1998 integrated research report. R and D on advanced combustion technology under microgravity environment; 1993 - 1998 nendo sogo seika hokokusho. Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For developing advanced combustion technology by using JAMIC's facility, the advanced combustion technology research committee supported by researchers of universities, national institutes and industries was prepared in JSUP, and R and D using a microgravity experiment facility and the international joint research with NASA were carried out. By using the advanced experimental equipment and measuring instrument developed for microgravity experiments, studies were made on combustion and evaporation of fuel droplets, combustion characteristics of dense fuel, flammability limit and NO{sub x} generation mechanism, and such precious results were obtained as storage of abundant experimental data, explication of a combustion mechanism, preparation of a database and find of new phenomena. In the ground verification experiment using the newly fabricated advanced combustor test equipment, various data effective for developing high-efficiency low-pollution combustors were obtained. Through the joint research with NASA including 5 themes, various results and the real relationship between the researchers were also obtained. (NEDO)

  16. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  17. Fiscal 1999 basic survey for promotion of joint implementation. Overall study report on energy saving and CO2 reduction at Indocement Company; 1999 nendo Indo cement ni okeru shoene CO{sub 2} sakugen sogo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A study is made about the feasibility of energy saving and CO2 reduction at the Citeureup Plant of the Indocement Company, Indonesia. Future embodiment of a clean development mechanism (CDM) is also discussed. Points examined for improvement involve air quenching clinker cooler (AQC) efficiency (mixing of raw materials, use of combustion control technology, and modification into a new type AQC); the finishing process (installation of a preliminary clinker crusher and a high-efficiency classifier); and waste heat cogeneration using AQC exhaust. The amount of energy to be saved will be 61,866 tons/year in oil, promising a 10.9% energy saving and CO2 reduction. The project requires a fund of 5,988,025,000 yen in total. The financial internal rate of return (FIRR) based on the environmental special yen credit is a little low, but the payout period of 11 years is reasonable. A similar result is obtained when export financing by the ex-Exim Bank is studied. A general loan is not proper in view of overall profitability. With precedents showing that it is near impossible for such a project to enjoy environmental special yen credit, it is necessary for the Japanese Government to build a CDM-oriented system under which environmental special yen credit will be offered to private sectors. (NEDO)

  18. FY 1998 basic survey to promote the joint execution, etc. Overall repair plan of thermal power plants in Maritime Province of Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Enkaishu ni okeru karyoku hatsudensho sogo kaishu keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For thermal power plants in Maritime Province of Russia, a repair plan for effective reduction of emission of greenhouse effect gas was worked out as a draft plan for the joint execution. The project is to be implemented for the additional installation/replacement of boilers at Vladivostok No. 2 power plant, construction of a power plant as a substitute for Partizansk power plant, and new construction of Ussuriisk power plant. The draft plan includes the new installation of two gas-fired boilers/replacement of existing boilers at Vladivostok No. 2 power plant, construction of 200MW cogeneration facility at Partizansk power plant, construction of 180MW cogeneration facility at Ussuriisk power plant, abolition of small-sized boiler station, etc. The reduction amount of the greenhouse effect gas emission based on this repair plan totaled 338 million tons in project. The effect against cost is US$ 4.75 per 1 CO2 ton at Vladivostok. (NEDO)

  19. Fiscal 1993 survey of the base arrangement promotion for foreign coal import. Survey of the general situation of Thai coal; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Thai sekitan sogo jijo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the energy situation in Thailand, the present and future status of coal supply/demand, the present situation of environmental policy and air pollution prevention policy and problems concerning coal and the measures for solution, and a possibility of Japan`s cooperation. In Thailand, the total coal supply amount in 1992 is 16.079 million tons, which is 9.1% of all the primary energy supply amount. The country produces only a few amount of anthracite and subbituminous coal beside brown coal. The domestic coal equals brown coal, the production of which was 15.335 million tons in 1992, 13.9% of all the primary energy demand. Concerning brown coal, 79.7% of all the brown coal supply are for electric power use, and others for industrial use such as the cement industry. The remaining reserve in developed areas is 151.4 billion tons, and the proven reserve in undeveloped areas 756 million tons. The demand for import coal was 11.25 million tons in 1996, and is expected to be 201.73 million tons in 2000. The paper pointed out some problems arising from coal production and spread of coal utilization, and described measures to solve the problems and fields where there are possibilities of Japan`s cooperation. 36 refs., 44 figs., 73 tabs.

  20. Fiscal 1999 technical achievement report. Development project on international standards for developing new industry (Comprehensive research); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Sogo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development of 13 individual subjects whose achievements are expected to come into use on the international scale was started in fiscal 1998, to be completed in three years. Progress is reviewed for each of the subjects, and the findings are mentioned below. Research and development is progressing smoothly, specifications to be internationalized have been narrowed down, and it is now foreseen that the main points of the specifications to be presented will be successfully prepared. There are some subjects, however, about which it is difficult to specify to which technical committees they are to be submitted. Assistance, for instance supply of information, by technical committees involved is indispensable. The attitude toward international standardization taken by European and American business corporations visited for study by Japanese researchers is to be disseminated to Japanese business corporations since the information thus collected will help them. Although 75% of the 13 subjects have reached a level where they may be presented as specifications for international standardization, yet they need active support by organizations concerned and research of trends of internationalization-related institutions before they are actually accepted as international standards. (NEDO)

  1. Report on fundamental investigation in fiscal 2000 of intellectual property right management criteria at General Research Institute of Industrial Technologies; 2000 nendo sangyo gijutsu sogo kenkyusho chiteki zaisanken kanri kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Fundamental items of knowledge were collected on matters to form the base of management and utilization of intellectual property rights as the basic data for cooperation among industry, academia, and government. Activities were put into order on the following nine fields: 1) handling of tangible research property rights at universities, 2) the way the organization should be to support the cooperation between industry and academia - a mechanism at Massachusetts Institute of Technology (MIT), 3) licensing and technology transfer in India, 4) intellectual property trends for the 21st century, 5) management of intellectual property assets - in relation with the new current in the U.S. Patent Act, 6) comparative study of examination guidelines for computer-related inventions between the United States and Japan, 7) management of intellectual properties and business law aspects in the technology innovation times - examples in Seattle where IT and bio-technologies are originated from, 8) patents and bio-technical inventions, and 9) new movements in bio-technology patents. In Item 2), examples at MIT were studied on the way the organization should be to support the cooperation between industry and academia. The industry-academia cooperation is in action at various levels, not only in licensing, but also in the industrial liaison program, and consortiums. (NEDO)

  2. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  3. FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

  4. Achievement report for fiscal 1998 on business auxiliary to New Sunshine Program. Hot water-aided power generation plant development (Development of deep-seated geothermal resources exploitation technology and development of deep-seated geothermal resources excavating technology); 1998 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the general exploitation scheme, technological information is collected about cement overseas, DHM (down hole motor), etc. In the development of heat-resistant durable bits, an improved version of the 350 degrees C real bit manufactured in fiscal 1997 undergoes a test in a real bore, and is evaluated for its general performance. In the development of high-temperature cement slurries, the ultralow specific gravity cement slurry for casing cement developed in fiscal 1997 is subjected to evaluation. It is examined by chemical analysis and powder X-ray diffraction, and its fluidity, free water, rate of dehydration, and compression strength at 250 degrees C are measured. In a real bore test, a slurry of the optimum composition is prepared and then hardened, and the hardened body is kept exposed to geothermal environments for eight weeks. It is then found that the hardened body retains a compression strength of 70kgf/cm{sup 2}. In the development of a down hole motor, a scale model, real in diameter and shortened in length, is built of the motor section, and is tested in circulating water and oil at normal and high temperatures, and its behavior and performance are evaluated. (NEDO)

  5. Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource producing technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper reported the results of the fiscal 1996 R and D of the deep geothermal resource collecting/producing technology. In the design of the total development, characteristics of the well mouth of the deep reservoir were examined to evaluate properties of deep geothermal resource, and the necessity of the pressure design, etc. were clarified. As to PTSD logging technology, conducted were improvement of PT probe, manufacture of a sonde of which S probe was integrated with memory/battery modules, and the actual well experiment. Concerning PTC monitoring technology, an experiment was carried out on a high temperature use optical fiber GI type, and it was shown that the type was on a commercial level. Further, a prototype sampler with 300degC heat resistance was trially manufactured, and a test to confirm its work was conducted in the well in the Corn Wall area of the U.K. As to the production control technology, studied was the arrangement of the production control technology for deep geothermal resource. Moreover, an experiment was made to examine the effect of metal ions coexisting when silica in the deep fluid precipitates. 46 refs., 107 figs., 38 tabs.

  6. Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper reported the results of the fiscal 1995 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the trend of technical development was examined of bits, cement and DHM overseas. Further, the simulational prediction was conducted in deep geothermal drilling. As to the development of element technology of hard high temperature strata drilling, the R and D of seal mechanism, bearing mechanism and cutter mechanism were carried out aiming at developing heat resistant/durable bits, and a bit was trially manufactured which was integrated with element parts selected by each element technology. Concerning the development of high temperature drilling mud, studies were made of the development of drilling mud materials, a mud system, etc. Relating to the development of high temperature cement slurry, the development was conducted of high temperature cement, dewatering adjusting agents, etc. As to the development of high accuracy much inclination drilling technology, in the development of high temperature use downhole motor, tests on heat resistance/durability were carried out in the mud of 12 kinds of high heat resistant stator materials. 175 figs., 137 tabs.

  7. Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper reported the results of the fiscal 1996 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the planned adjustment of actual well tests was conducted on bits and drilling mud at the time of drilling the exploration well of the Kakkonda area. As to the trend of overseas technology, examined was the developmental trend of high temperature type downhole motor products. In the development of hard high temperature strata drilling element technology, a drilling test was carried out on trially manufactured 300degC heat resistant/durable bits. In the development of high temperature drilling mud, drilling was done in the mud of thermally stable quality in the actual well experiment using the 300degC mud system. In the development of high temperature use cement and high temperature use cement slurry, a possibility was obtained of composing a slurry which has the targeted dewatering amount, compressive strength, and water permeability. In the development of high temperature downhole motor, data on characteristics of heat resistant stator materials were arranged in a relationship among the abrasion amount, thermal expansion amount and elastic recovery amount, and the database was obtained. 166 figs., 148 tabs.

  8. Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

  9. Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

  10. Environments of ocean and primary productivity during the late Quaternary. Millenial-scale large and abrupt climatic changes (global system dynamics in response to Dansgaard-Oeschger cycles); Daiyonki koki no kaiyo kankyo to seibutsu seisan. Suhyaku-susennen scale no kyugekina kiko hendo (Dansgaard-Oeschger cycle ni taisuru chikyu system no oto)

    Energy Technology Data Exchange (ETDEWEB)

    Tada, R. [The University of Tokyo, Tokyo (Japan)

    1998-04-25

    Abrupt and steep climate changes of the millennial scale as represented by the Dansgaard-Oeschger cycle (D-O cycle) and the behavior of the global surface layer system in their wake are outlined. The D-DO cycle is the abrupt and steep climate changes that are recorded in the Greenland continental ice sheet, and is grasped most typically as changes in the oxygen isotopic ratio in the ice. Studies reveal that the D-O cycle is a global episode that accompanied interaction between various subsystems constituting the global surface layer system. It is believed that in the D-O cycle there were changes not only in temperature but also in aridity/moisture and in the sea level, and probabilities are high that there was a great local variation in the way the changes took effect. The possibility has now become lower that the D-O cycle occurred in the interglacial epoch in the high latitude belt in the northern hemisphere, yet it remains likely that the climate changes driving the D-O cycle continued in the low latitude belt. 57 refs., 8 figs.

  11. Study of internal wave generation by tide-topography interaction; Lecture by the member awarded the Okada Prize of the Oceanographical Society of Japan for 1989. Choryu niyoru naibuha no hassei kiko ni kansuru kenkyu; 1989 nendo Nippon kaiyo gakkai Okadasho jusho kinen koen

    Energy Technology Data Exchange (ETDEWEB)

    Hibiya, T. (Univ. of Tokyo (Japan). Earthquake Research Inst.)

    1990-02-25

    With regard to internal waves under strong tidal flows generated in the Amakusanada, Kyushu, the Canadian West Coast Region and the U.S. Eastern Coast Region, this study explains the theory of their generation mechanism showing the examples of its applicayion to the actual maritime regions, then by developing this theory, discusses the role of its vertical shear effect in the generation process of internal waves in case where the stationary two layer alternative flow lies on top of a strong tidal flow like the inside of straits and fjords, etc.. Furthermore, it clarifies the effect of the vertical mixing on the seawater alternating process inside and outside of the fjord taking place on the both sides of the above mixing when such a vertical mixing is caused by breaking waves of the internal tidal flows over a sill in the fjord, as an example of an important role taken by the internal waves with large wave heights thus generated. 28 refs., 12 figs.

  12. Technology to prevent deposition of marine organisms by means of electrically conductive coating. Discussions on current and potential distribution by using experiments; Doden tomaku ni yoru kaiyo seibutsu fuchaku boshi gijutsu. Denryu den`i bunpu ni kansuru jikken ni yoru kento

    Energy Technology Data Exchange (ETDEWEB)

    Usami, M; Masaki, T [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Ueda, K

    1996-04-10

    Steel structures in sea water and surface of hulls are deposited with such marine organisms as microorganisms, algae and shellfish. The deposition causes a large problem such as occurrence of abnormal local corrosion in the structures, and increase in cruising resistance in ocean vessels. The present study has introduced a simplified equation of estimation for current and potential distribution in parts coated with an electrically conductive film, and verified its reasonability by an experiment. The equation of estimation was introduced by following a model of current flow in the electrically conductive coating. The experiment has the conductive coating applied to the interior of a concrete water tank with a length of 10.8 m, a width of 5 m and a depth of 3 m to measure potential at different locations. The conductive coating was energized from copper foils attached on each applied face, whereas the current was applied to two faces between the conductive films as a pair among the four coating applied faces to measure potential in each location. A simulated calculation revealed that the potential range in the depth direction is made smaller if specific resistance of the conductive film is decreased, and made greater if increased. Effectiveness of the equation of estimation was verified by an experiment. This method has provided a prospect of achieving optimization of the specification for application of the conductive film. 2 refs., 7 figs.

  13. Study of thermal threshold and counter-measures for human body in oceanic working environment. 1st Report. Heat balance model and heat storage index; Shonetsu kankyoka no kaiyo sagyo ni okeru netsuteki genkai to onnetsu taisaku ni kansuru kenkyu. 1. Netsu shushi model to onnetsu shisu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Nakamura, M. [Tokyo Gakugei University, Tokyo (Japan); Murayama, M.

    1996-12-31

    Identification was intended on effects of such thermal factors as metabolic amount, environmental temperature and humidity, and clothing resistance on human body temperatures during works under hot environments. Therefore, measurements were carried out on human skin temperatures, rectum temperatures and humidity inside clothing, while amount of motion, environmental temperature, and clothing are changed in a constant temperature room and under a sun irradiation environment. Furthermore, a heat balance model was prepared, which divides the objects into an outer shell layer whose temperature changes depending on the result of this experiment and into a core having constant temperature characteristics. An equation to derive skin temperatures was introduced from the model. The equation formulated a calculation formula for heat accumulation in human body, which can be used as a hot heat index. Relationship between thermal factors and heat storage amount was investigated to consider a thermal limit for a physical work. An equation to derive skin temperatures was confirmed capable of expressing general change in skin temperatures, being proved by comparison with experiments. Calculation formulas for amount of heat stored in human body were shown capable of expressing influence of different thermal factors, the expression being useful as a hot heat index. Calculating the human body heat storage is very largely affected by effect of sweat to dissipate heat, hence it is necessary to improve the accuracy including that for body temperature adjusting reactions. 17 refs., 17 figs., 5 tabs.

  14. Study of thermal threshold and counter-measures for human body in oceanic working environment. 1st Report. Heat balance model and heat storage index; Shonetsu kankyoka no kaiyo sagyo ni okeru netsuteki genkai to onnetsu taisaku ni kansuru kenkyu. 1. Netsu shushi model to onnetsu shisu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Nakamura, M [Tokyo Gakugei University, Tokyo (Japan); Murayama, M

    1997-12-31

    Identification was intended on effects of such thermal factors as metabolic amount, environmental temperature and humidity, and clothing resistance on human body temperatures during works under hot environments. Therefore, measurements were carried out on human skin temperatures, rectum temperatures and humidity inside clothing, while amount of motion, environmental temperature, and clothing are changed in a constant temperature room and under a sun irradiation environment. Furthermore, a heat balance model was prepared, which divides the objects into an outer shell layer whose temperature changes depending on the result of this experiment and into a core having constant temperature characteristics. An equation to derive skin temperatures was introduced from the model. The equation formulated a calculation formula for heat accumulation in human body, which can be used as a hot heat index. Relationship between thermal factors and heat storage amount was investigated to consider a thermal limit for a physical work. An equation to derive skin temperatures was confirmed capable of expressing general change in skin temperatures, being proved by comparison with experiments. Calculation formulas for amount of heat stored in human body were shown capable of expressing influence of different thermal factors, the expression being useful as a hot heat index. Calculating the human body heat storage is very largely affected by effect of sweat to dissipate heat, hence it is necessary to improve the accuracy including that for body temperature adjusting reactions. 17 refs., 17 figs., 5 tabs.

  15. Exploration for petroleum and natural gas in Sonai Plain

    Energy Technology Data Exchange (ETDEWEB)

    Konishi, K

    1965-09-01

    Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

  16. Bothid larvae (Pleuronectiformes - Pisces) of the Gulf of Thailand and South China Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Devi, C.B.L.

    , Paralichthidae and Bothidae). Kaiyo Kagaku, 11 (2): 100-110 (in Japanese). Amaoka, K., 1984. Bothidae in The fishes of the Japanese Archipelago edited by H. Masuda et al. Tokai Univ. Press. Tokyo. 347-350. 70 LALITHAMBIKA DEVI i Amaoka, K. and E. Yamamoto..., with notes on the species of genus Bothus in Japanese waters. J. Oceanogr. Soc. Jap., 1 (1-2) : 133-140. Kyusin, K., Amaoka, K., Nakaya, K., Ida., H., Tanino, Y. and Senta, T. 1982. Fishes of the S outh China Sea. Japan Fish. Reso. Res. Center, Tokyo 333 pp...

  17. FY 1984 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential quantity supplied of overseas resource (Survey of the potential quantity supplied of methanol); 1984 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru kyokyu kano ryo chosa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    Based on the results of the survey of the potential quantity supplied of overseas resource which was made from FY 1981 to FY 1983, the paper predicted the world methanol supply plan, changes in the oil situation, economical efficiency of methanol and the competitive power with petroleum products, etc., and studied the time of potential supply, areas of potential supply and supply potential of power generation use methanol during the period toward 2000. In case the comparatively low crude oil price is predicted due to the energy supply/demand (Scenario A), the supply potential of power generation use methanol in four projects on methanol production taken up as trial calculation example is considered very low. Even in case the comparatively high crude oil price is predicted (Scenario C), it is in 1989 that the methanol market price becomes equivalent in heat quantity to the crude oil price. It is difficult to expect the potential before 1989. In case of the intermediate case between Scenario A and Scenario C (Scenario B), it is in 1993 that the methanol price becomes equivalent in heat quantity to the crude oil price. It is difficult to expect the potential before 1993. (NEDO)

  18. FY 1999 report on the results by the district consortium research and development business venture supporting type district consortium (central industry creation type). Development of technologies for producing secondary products from unutilized wood resources for zero emissions; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Zero emission wo mezashita miriyo mokushitsu shigen no niji seihinka gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of secondary products from unutilized wood resources, to establish zero waste emissions at wood-related plants. Described herein are the FY 1999 results. The program for manufacturing and development of VOC-free interior products has successfully developed the wood boards using only inorganic adhesives, and the techniques for production of doors of unique, monolithic structure. The program for manufacturing and development of artificial wood with high performances has developed the techniques for forming composites of waste wood and thermoplastic materials, to produce the shapes of artificial wood containing 85% of wood and having touch close to that of wood. The program for production of agricultural and construction materials by the barks has developed the techniques for producing pavement and mulching materials as civil engineering and landscaping materials, and pot type culture grounds for high-class flowering plants as the agricultural materials from cypress and cedar barks. Information regarding performance levels, and discrimination and superiority over the products by competitors has been collected from various sources, e.g., internets, and academic meetings and literature, for the monolithically formed doors, extruded products, mulching materials and pot-type culture grounds. (NEDO)

  19. Fiscal 1997 industrial technology R and D project. Research report on development of use technology of bio- resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This project aims to establish production technology of functional substances, oil degradation and purification technology, and use technology of unused oil fraction through development of cultivation control technology of complex biosystems. For functional material production technology, as functional substances some specific marine bacteria inhibitors, antibreeding substances of microalgae, and UV absorption substances were isolated. The productivity of korormicin as specific inhibitor against marine bacteria was improved considerably by cultivation method. For research on molecular genetic analysis technology, a new identification technology and a simple automatic analysis system of microeucaryotes using genes were developed. For global environment purification technology such as efficient degradation of pollutants, study was made on cultivation control technology of phenol- degrading consortia, population dynamics of oil-degrading microbial consortia and a restoration method of oil pollution by complex biosystem at lower temperature, and the demonstration experiment of oil degradation were carried out. (NEDO)

  20. Fiscal 1996 research cooperation promotion project. Report on the Japan/Mexico international cooperation research on recovery of valuable elements in brine; 1996 nendo kenkyu kyoryoku suishin jigyo. Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku follow up hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the research cooperation promotion projects having been carried out, the R and D of an overall recovery system have been conducted which recovers effectively and systematically valuable resources such as magnesium, bromine and boron including in brine made after the salt manufacturing in the coastal region in Mexico. In this project, as the research on the distilling process needed for commercialization of the system to recover valuable resources from the brine, Japan has been collecting information on various distilling processes and solar pond systems and studying a distilling process appropriate to the site jointly with Mexico. As a result, a seawater desalination process which combined the solar pond using solar energy and the evaporation method was recommended as a low-priced distilling method. Moreover, it was indicated that the solar still method for condensing/recovering the evaporated water of the Guerrero Negro salt pan is also less influential in the salt manufacturing process and is viable as a most economical distilling process by studying the structural design and operational method of more efficient solar stills

  1. Research cooperation promotion business for fiscal 1998. Research cooperation in the development of environmentally-friendly high-efficiency mineral resources extracting and processing technologies; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research cooperation was conducted in the Republic of Kazakhstan for efficiently extracting and collecting valuable metals (gold, silver, copper, and rare metals) contained in volume in the slag generated by mining operation, with caution exercised not to disturb the environment. The research items taken up for development involved technologies of the leaching of the target elements using sulfuric acid, microbes, etc.; extraction using solvents; electroextraction; collection of gold and silver; and the treatment of waste water. In fiscal 1998, the wet process and the processing of gold and silver were studied, for which the specimens sampled at the research site in and after fiscal 1996 were used. As for the fabrication of pilot plant facilities, all were completed in fiscal 1998, and part of them was transported to the research site. Procurement and transportation necessary for the joint research were also carried out. Furthermore, to ensure effective execution of the project, scientists were invited from Vniitsvetmet, the Kazakhstan research institute for non-ferrous metals, for training, who included the institute director, deputy director, patent/liaison department chief, and two researchers. (NEDO)

  2. Research cooperation promoting project in fiscal 1998. Research cooperation related to developing mine resources extraction and treatment technologies of environment harmonizing and high efficiency type; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to realize more effective utilization of non-ferrous metal resources, joint research cooperation is made with the Republic of Kazakhstan. It is intended that valuable metals (gold, silver, copper, rare metals, and others) contained at large quantity in ore scraps generated in association with mine operation be extracted and recovered efficiently paying considerations to the environment. The treatment process consists of the following conception: raw materials such as ore scraps are leached by sulfuric acid and microorganisms to separate and recover gold and silver; the leach liquor containing valuable metals is extracted by using solvent and recovered of copper and rare metals via an electrolytic process; and the waste water is treated and discharged. Fiscal 1998 has performed studies on the wet treatment system at the site and in Japan, the gold and silver treatment, and the waste water treatment by using samples collected from the site in fiscal 1996. Based on the results of these fundamental studies, a pilot plant was built, and all of the facility fabrication was completed in fiscal 1998. Part of the facilities has been transported to the site. To drive the project forward effectively, materials and items of equipment required for the joint research were procured and transported to the country, and at the same time Kazakhstanian researchers were received in Japan for training. (NEDO)

  3. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the bioconsortium system utilization/production technology); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Fukugou seibutsukei riyo seisan gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the functional substance production technology, petroleum degrading/cleaning technology and high-grade utilization technology of the unused petroleum fraction, study was conducted of the culture control technology in substance production and substance decomposition by bioconsortia, and the FY 1999 results were reported. As to the functional material production technology, study was made of the separation/culture technology, functional substance production technology using bioconsortia (control substance searching method in the ocean microbial consortia system, isolation of control substance/structure determination/separation of production bacteria, elucidation of the inter-species communication substance function, heightening of function of the production microbial consortia), etc. Concerning the effective degrading/cleaning technology of petroleum compounds, study was made of the molecular genetic analysis technology, histochemical analysis technology, analysis technology of the solvent resistance mechanism, bioconsortia analysis system technology, global environmental purification technology such as the effective decomposition of environmental pollutants, etc. Relating to the high-grade utilization technology of the unused petroleum fraction, study was made of the chemical analysis of the photolysis crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

  4. Fiscal 1997 research report on development of use technology of bio-resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho (fukugo seibutsukei riyo seisan gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report summarizes the fiscal 1997 research results on production technology of functional materials, and the research study result for utilizing substance production and decomposition by complex biosystem for industries. For detecting technique of microorganisms in soil, staining by CFDA-AM was suitable, and allowed visualization of sulfate- reducing bacteria during culture. For research on functional analysis technology, study was made on atomic force microscope technology to detect microorganisms in environment and observe their fine structures. For research on detection, separation and cultivation technology of difficult-to-culture microorganisms, a molecular genetic analysis method of microbial communities and a determination method of their viability were selected. For functional substance production technology, study was made on technical utilization of bioflocculant produced by microbial consortia as environment-friendly oil removal reagent, and on gene transfer control in microbial consortia. For the research study for the project, survey was made on useful substances produced by complex biosystem. (NEDO)

  5. FY 2000 report on the coal resource development basic survey (information collection analysis project). Cooperative project on the open-cut coal mine rehabilitation technology; 2000 nendo sekitan shigen kaihatsu kiso chosa (joho shushu kaiseki jigyo) hokokusho. Rotenbori sekitan saikutsu atochi shufuku gijutsu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    At the Ensham open-cut mine in Australia, an investigational survey was conducted of a new rehabilitation technology which can contribute also to securing CO sink with the aim of preventing global warming, and the FY 2000 results were summed up. In the survey, the surface soil, sand silt layer, brown rock layer, gray sandstone layer and coal seam were moved from open pits, the goaf was embanked, and the experimental section was set up. As to the place for test, conducted were collection of information on adaptive plant species, bacterium species, meteorology and precipitation pattern, soil analysis, etc. Concerning the bacteria, bacteria were newly separated and tested at the survey site, besides the species to be tested. After planting, measurement of the growth amount of plants, etc. were conducted grasping the meteorology and the water-pouring state during cultivation. For the basement, three kinds of spoils were used, and permeability is different in each spoil. Permeability is an important factor to plants. Too good permeability and too bad permeability are both not good. A future follow-up survey will make what kind of spoil is suitable for eucalypti possible. (NEDO)

  6. Fiscal 1998 R and D project on industrial technology. Development report on use technology of bioresources such as bioconsortia (Development of analysis technology of bioconsortia); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For use of advanced functions of bioconsortia (complex microorganisms composed of more than 2 microorganisms with certain specific function), this project analyzes specific functions of specific organisms and the interaction between the specific functions, and develops isolation and incubation technologies of component organisms. In fiscal 1998, to promote this project, the meetings were held frequently in National Institute of Bioscience and human Technology. Study was made on production of useful substances and useful degradation functions in association with bioconsortia. The result showed that microorganisms coexisting with nematode produced physiologically active substances exhibiting antimicrobial activities to tubercle bacillus, MRSA and others, microorganisms coexisting in eggs of some insects produced substances having antiviral activities and activities against pathogenic bacteria in a plant, and microorganisms growing in some plants or mycorrhiza organisms produced insecticidal substances or growing-promoting substance. The basic understanding was obtained on cooperative actions of bioconsortia to bioremediation and degradation of organic substances. (NEDO)

  7. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  8. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of complex biosystem analyzing technology; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The aim is to utilize the sophisticated functions of complex biosystems. In the research and development of technologies for effectively utilizing unexploited resources and substances such as seeweeds and algae, seaweeds are added to seawater to turn into a microbial suspension after the passage of two weeks, the suspension is next scattered on a carageenan culture medium, and then carageenan decomposing microbes are obtained. In the research and development of technologies for utilizing microbe/fauna-flora complex systems, technologies for exploring and analyzing microbes are studied. For this purpose, 48 kinds of sponges and 300 kinds of bacteria symbiotic with the sponges are sampled in Malaysia. Out of them, 15 exhibit enzyme inhibition and Artemia salina lethality activities. In the development of technologies for analyzing the functions of microbes engaged in the production of useful resources and substances for animals and plants, 150 kinds of micro-algae are subjected to screening using protease and chitinase inhibiting activities as the indexes, and it is found that an extract of Isochrysis galbana displays an intense inhibitory activity. The alga is cultured in quantities, the active component is isolated from 20g of dried alga, and its constitution is determined. (NEDO)

  9. FY 1999 report on the results of the investigational study on the promotion of application of aluminum materials to automobiles by the development of low-cost aluminum materials and aluminum resource recycling technology; 1999 nendo tei cost aluminium zai oyobi arumi shigen junkan gijutsu no kaihatsu ni yoru jidosha eno aluminium zai tekiyo suishin ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Presently, the aluminum demand in Japan is approximately 3.8 million tons, and the aluminum discharged as scrap reaches approximately 1.7 million tons/year. Out of the discharged scrap, 54% is recovered as the secondary metal, and the rest, 0.77 million tons, is not recovered and dumped for land reclamation. In future, if the present cascade type recycling goes on, it is predicted that a gap between supply and demand of about 0.5 million tons will arise. To cope with this problem, the following are the measures to be taken : 1) development of the technology to promote the use of recycled aluminum metal for automobiles in which a lot of aluminum is most likely to be used because of the increasing fuel consumption, etc. 2) establishment of a recycling system by which the waste sash discharged in quantity from the construction field is again used as sash. From the two points of view, which are needed in the case of using a lot of aluminum for automobiles, the heightening of competitiveness in the aluminum industry and the recycling in which the aluminum expanded materials used for automobiles are efficiently recycled as expanded materials in the recycling economic system, this survey extracted problems and made proposals, overlooking the state of the aluminum use in automobiles, state of the treatment of used cars, state of manufacturing/processing technology of aluminum products. (NEDO)

  10. Report on an investigational research on intensive arrangement of the resource recycling type/energy conservation type lifeline system which survives disaster; 1995 nendo shigen recycle gata shoshigengata no saigai ni tsuyoi life line no shuyaku seibi system no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the necessity of reducing waste construction materials and reutilizing as resource, the paper studied the issue on earthquake waste, in particular. Facilities of electric power/gas, water supply and sewerage system, roads, railroads, information, etc. are lifelines to support city life. Large earthquakes damage various lifelines and paralyze urban functions, and at the same time, produce a large quantity of waste due to the dismantlement of structures hit by earthquake, etc. It is important that the system is too tough to suffer damage, but more important that it is easily repaired. A large scale of underground multi-purpose duct has enough redundancy to absorb external force even if the duct itself is damaged. Such large-scaled and antiseismic ducts are so high-priced that they cannot be deliberately distributed all over the city. Therefore, the paper proposed simple ducts installed under the sidewalk. The duct is a U duct with a cover easy to remove, and is easily repaired. As duct materials, resin concrete using waste materials, etc. are considered. There still are a lot of problems to be solved such as expense sharing with the main body of business and legal restrictions. 25 figs., 36 tabs.

  11. FY1995 design of environment-friendly and generation-type conversion title of system for unused carbon resources by developing highly functional materials; 1995 nendo kokino zakryo kaihatsu ni yoru kankyo chowagata jisedai miriyo tanso shigen tenkan system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Carbon resources such as coal, heavy oil, bitumen and so on are not suitable for the utilization as energy resources from the view-point of the global environment because those contain a great deal of heteroatoms, minerals and water. Therefore, the purpose of this project is to establish the environment-friendly and next generation-type conversion system for unused carbon resources by developing highly functional materials. This project aims at the following researches necessary to establish the conversion system for the unused carbon resources. (1) Development of technologies for pre-treating carbon resources (2) Development of recoverable hydrogenation catalysts capable of repeated use (3) Development of gasification catalysts active at low temperatures (4) Development of inorganic membranes for H{sub 2} or CO{sub 2} separation (5) Development of adsorption separation technologies in the supercritical phase (6) Development of highly active catalysts for CO hydrogenation Each development has been successfully completed and we have much prospect of establishing the conversion system for unused carbon resources. (NEDO)

  12. Fiscal 2000 basic survey for coal resource exploration. Survey for development of new exploration technology (Exploration of shallow layers on the land - Collection of data and materials); 2000 nendo sekitan shigen kaihatsu kiso chosa shiryoshu. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    As agreed upon between NEDO (New Energy and Industrial Technology Development Organization), Japan, and Queensland, Australia, joint research was conducted on new technology for coal exploration within Queensland, and data collected during the research and related materials are compiled into this book. The book contains the Agreement for the Joint Research of New Technology in the Geophysical Exploration of Coal Resources (Japanese and English), GPS (global positioning system) survey results along 2-dimensional seismic reflection method traverse lines, GPS survey results along 3-dimensional seismic reflection method traverse lines, seismic generator vehicle inspection and repair report, geophysical logging observer's logs and test bore dip measurement data sheets, examples of outputted shot records (2-dimensional seismic reflection method), examples of outputted shot records (3-dimensional seismic reflection method), analysis and testing report on Girrah layer samples, reference literature on PRBS (pseudorandom binary sequence), collections of photographs of cores sampled by test boring (BG001, BG002, BG003, BG004), collections of other photographs, and so forth. (NEDO)

  13. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  14. Report on achievements in fiscal 1998. Research on acceleration of improving the base for biological resource information, and development of a technology to measure gene information (development of the DNA measuring technology using bead arrays); 1998 nendo seibutsu shigen joho kiban seibi kasokuka kenkyu idenshi joho no keisoku gijutsu no kaihatsu seika hokokusho. Bizu array wo mochiita DNA keisoku gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It is necessary in the field of post-genoms to know statistical correlation between DNA orientation information and clinical data, which helped growth of DNA probe arrays (DNA chips). However, it is difficult in patent point of view to develop chips in Japan. On the other hand, a movement has begun to use beads fixed with DNA probes in place of DNA chips demarcated on the surface of solids. This is a method to investigate hybridized DNA by means of fluorescent detection, in which each bead retaining the DNA probes is colored to make identification of the retained probes possible, and hybridizing reaction is performed in aqueous solution. Hitachi has developed a DNA measuring technology using bead arrays. The bead array has probe fixing beads of about 100 {mu} m laid sequentially inside a capillary, wherein the array can be used to inspect a large number of genes. Thus, this method can be a DNA measuring technology which is inexpensive, and high in reproducibility. These features lead to a belief that the technology is suitable for gene inspection devices used in the process of medicine development and at the clinical sites. (NEDO)

  15. Survey report for fiscal 1999 on internationalization of technologies for effective use of energy resources. Survey by exploration of international cooperative researches on energy-saving through advanced use of steel slag; 1999 nendo energy shigen yuko riyo gijutsu kenkyu kokusaika chosa hokokusho. Tekko slag no kodo riyo ni yoru sho energy gijutsu ni kansuru kokusai kyodo kenkyu no tansaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As for the collection of sensible heat, 1/3 of blast-furnace slag is treated to the purpose at the Teesside Technology Centre, Britain, but none is collected in the latter half of tapping in case there is so much slag that cooling cannot be done in time. In the case of a large blast furnace, some measures have to be contrived because molten iron comes out of the furnace intermittently. In Germany, the heat collection rate is as low as 3%, with no effort made at heat collection. In North America, desire to develop such a technology is not strong. A visit was made to the Institute of Ocean Sciences, Canada, in relation to the concept of using steel slag as a eutrophic source for marine photo-plankton. A large-scale long-term test is under way for examining the relationship between global warming and ocean current circulation. There are possibilities that Japan will enter into the project for a joint study, for example, of heavy metal elution from slag though the test fails to name slag as the direct object of study. Not only for Canada but also for any other country who faces the sea, it may be a meaningful national policy to inject some active ingredients into the sea for an increase in living marine resources. Greece is engaged in the ocean dumping of nickel slag on an experimental basis but, in view of the purpose of the experiment, Japan will not be a participant in the project. (NEDO)

  16. FY 1984 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential quantity supplied of overseas resource (Survey of the usability of methanol); 1984 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru riyo kanosei chosa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The paper studied a scenario of the demand for power generation use methanol in Japan by grasping the situation of the utilization of methanol as fuel in the world, studying a scenario of power supply and the positioning of methanol power generation in Japan, doing a trial calculation of the breakeven price of power generation use methanol, etc. As to the usability of power generation use methanol as fuel, in the use for the reformed gas turbine and fuel cell, there is a possibility of making up for the disadvantage in fuel price by future technical development. For the fuel conversion at existing coal-fired power plants and the application of methanol to combined cycle and newly-installed boiler, it is necessary to have a substantial drop in methanol price. Taking an advantage that methanol can be transported in small size and easily be stored, methanol can possibly be used as fuel for dispersed power sources. The potential demand for petroleum substituting methanol is estimated at approximately 25 million t/y, assuming it to be 1/2 of the petroleum consumption amount. The present methanol market in the world is not so large for quantity use as fuel, and for the introduction, therefore, it is necessary to secure flexibility in supply. (NEDO)

  17. Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium in its 2nd year--Creation of key industries (Development of manufacturing system for multiple applications of biological resources); 1998 nendo yuyo seibutsu shigen no tamokuteki riyo no tame no kako seizo system no kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is conducted to collect intermediate products from Okinawan herbs for the production of antioxidant products usable for various purposes. Substance-producing plants are screened and the substances they offer are assessed for antioxidant activity, extracted, processed, prepared for market, and checked for safety. At the Okinawa Industrial Technology Center, a DPPH (1,1-diphenyl-2-picrylhydrazyl)/microplate method has been established, which promptly measures the antioxidant activity of the substances. Using this technology, the divisions concerned of industrial, academic, and governmental organizations cooperate with each other over the optimization of herb cultivation technology, development of a herbal ingredient analyzing technology, efficacy of herbs, development of a safety assessment system, development of a technology for the effective extraction, processing, and preparation of herbal ingredients, and the development of a technology of assessing antioxidant intermediate products for their efficacy. As the result, a technology is established of producing intermediate antioxidant products from Guava, Ryukyuyomogi, and Ukonisomatsu. They are unique Okinawan products, and sell at 40,000-50,000 yen. Since the prices are equal to or lower than the prices of other antioxidant intermediate products, probabilities are very high that they will get into markets in Japan proper. (NEDO)

  18. FY 1998 R and D of utilization of biological resources such as those in bioconsortia. Report on development results of techniques for utilization/production of organisms in bioconsortia; 1998 nendo fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to analyze functions and interactions of organisms having specific functions, to develop the techniques for isolating and cultivating the constituent organisms, and thereby to develop the techniques for their industrial utilization, in order to develop the techniques for handling organisms in bioconsortia as the techniques to utilize their functions, e.g., production and decomposition of materials, and also to develop the techniques for culturing/controlling microorganisms in bioconsortia and for strengthening their functions. The FY 1998 themes are development of the functional material production technology, and comprehensive study for the project. More concretely, the former includes histochemical analytical technology (development of techniques for detecting microorganisms in soil, and of techniques for in-situ detection/isolation of specific microorganisms in bioconsortia and for analysis their functions), isolation and culture technology (development of detection, separation and cultivation technology of microorganisms that are not easily cultured), functional substance production technology (technical utilization of microbial consortia for production of environment-friendly oil/water separation polymers), and functional material production technology (development of methods for artificial gene exchange in microbial consortia). (NEDO)

  19. Report on achievements in fiscal 1999. Development of technology to utilize biological resources such as composite organism systems (development of technology to utilize and produce composite organism systems); 1999 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    It is intended to achieve the following objectives in terms of the technologies to utilize such functions as material production and material decomposition by using composite organism systems: develop a technology to handle the composite organism systems; establish a composite microorganism cultivation control technology, and a composite microorganism system function strengthening technology; develop a technology to separate and cultivate organism groups constituting them, and develop industrial utilization technologies. The fiscal 1999 has discussed developing the elementary technologies for the technology to utilize functions of the composite organism systems on the following research items: 1. a functional material production technology; and 2. comprehensive investigations and researches. In Item 1, development was made on a technology to detect, separate and cultivate microorganisms in soil as the histochemical analytical technology. Development was made on an in situ detection, separation and function analyzing technology for particular composite microorganisms as the function analyzing technology. In the separation and cultivation technology, development was made on a technology to detect, separate and cultivate difficult-to-cultivate microorganisms. In the functional material production technology, development was made on a technology to utilize microbial consortia producing environmentally harmonizing oil-water separating polymers, and a method to execute artificially the gene exchange in the microbial consortia. (NEDO)

  20. FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of developing the industrial utilization technology, analysis was made of functions and interactions of the specified functional biological groups, and at the same time the developmental study was made of the technology to isolate/culture the constitutive biological groups. The FY 1998 results were summed up. As to the technology to detect microorganisms in soil, the SFDA method was improved and the new dyeing method was developed. And, there almost was hope for the development. Concerning the functional analysis technology, the functional substances peculiarly manifested only in the complex system in the ocean environment are searched. Several kinds of compounds were found out, and at the same time the test to confirm the biological activity is under way. Relating to the isolation/culture technology, study was made on rotten fruit, and the existence in the sample of the microorganisms which are difficult in isolation/culture was newly confirmed. In regard to the culture of the microorganisms which are difficult in isolation/culture, availability of the replica method was found out. As to the technology to produce functional substances, studies were made on the following: utilization technology of the environmental harmony type oil/water separation polymer producing microbial consortia, method to artificially make gene exchanges in the microbial consortia, etc. (NEDO)

  1. FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology. Basic design of pilot plant and a part of the detailed design; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku. Pilot plant no kihon sekkei oyobi ichibu shosai sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This project is a cooperative research on the development of environmental harmony type high efficiency mineral resource extraction/treatment technology. It aims to study/develop a system to recover valuable metals from unused resources in the Republic of Kazakhstan using the environmental harmony type technology which is easy to operate/maintain and is environmentally friendly with no mine pollution caused. In the project, which started in FY 1994, a pilot plant is finally constructed in Kazakhstan, a recovery system to be applied is demonstrated, and the comprehensive assessment of the system is made. Concretely, the recovery of Cu, Au, Ag, etc. is tried from the Nikolayevska low grade ore and Zhezkent tailings. This is a system into which the following techniques are integrated: treatment before dressing such as flotation, leaching of Cu, etc. by acid including bacteria, solvent leaching, electrowinning, cyanogen leaching activated carbon treatment and wastewater treatment of Au and Ag. As to the design/fabrication of pilot plant, conducted was the conceptual design in FY 1995, and the basic design, a part of the detailed design (crushing/grinding/leaching/dewatering facilities of the process of the acid (bacteria) leaching of Cu, etc.), and the fabrication in FY 1996. (NEDO).

  2. FY 1998 basic survey for coal resource development. Data collection of the joint research of new technology in the geophysical exploration of coal resources (land area shallow seam survey); 1998 nendo sekitan shigen kaihatsu kiso chosa shiryoshu. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This is a compilation of the data on the coal resource land area shallow seam survey conducted in FY 1998 as the basic survey for coal resource development. The trend survey was made from July 26 to August 6, 1998. The purposes of the survey are to study the image analysis method, examples of application of the reflection seismic survey to coal, and inversion technology. The data compilation includes the following: 1. Minutes of the proceedings of the FY 1998 Japan-Australia steering committee (in English). 2. Data/proceedings of the FY 1998 Japan-Australia technical study committee (in English). 3. Results of the GPS measurement of reflection seismic survey traverse lines in Caroona district. 4. List of parameters in the FY 1998 reflection seismic survey data processing. 5. Report on the work of inspection/repair of seismic pulse generator. 6. List of the data on diameter of the test boring conducted in FY 1998. 7. NEDO-DMR CAROONA DDH borehole core pictures. 8. Estimated curves. 9. Report on the trend survey of the FY 1998 coal resource development basic survey (land area shallow seam survey). 10. Pictures. 11. Data on the 1st (FY 1998) new exploration technology study committee. (NEDO)

  3. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the consortium based analysis technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made to look for the consortium based analysis technology by which the consortium base can be analyzed as it is using the molecular biological method. Studies were made in the following four fields: 1) new identification technology of eucaryote using II DNA topoisomerase genes (PCR amplification method of II DNA topoisomerase genes); 2) method to detect new recognition peptide activated microorganism (adjustment of cortical antigen); 3) technology to elucidate detection/response mechanism of the specific environment and adaptation/resistance mechanism of the specific environment; 4) incubation method inside 3D matrices. In 3), studies were made of the analysis of inhibition mechanism of korormicin and separation of solvent-resistant oil degradable bacteria. In 4), for the settlement and dynamic analysis of microorganism consortium by studying incubation conditions, conducted was the molecular system analysis of bacteria and eumycetes inhabiting in sponge. (NEDO)

  4. FY 1997 basic survey for coal resource development. Data collection of the joint research of new technology in the geophysical exploration of coal resources (water area medium depth seam survey); 1997 nendo sekitan shigen kaihatsu kiso chosa shiryoshu. Shintansa gijutsu chosa kaihatsu (suiiki chushindoso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In 'the new exploration technology test on coal resource' (water area medium depth seam exploration) jointly conducted between Japan and China, tests have been carried out for 5 years on the BDR-5 test boring measurement monitoring system and the diamond bit which are items of the technology development of high resolution seismic survey system and high efficiency test boring system. As a result, the new technology test was successful, and technical economic effects were obtained. The situation of the test was summarized. The following data were compiled as shown in Data No.1-12. 1. The proceedings of the FY 1997 Japan-China steering committee (No.9). 2. Report on the survey of China verification field South Sihu water level situation. 3. The proceedings of the FY 1997 Japan-China steering committee (final). 4. Report on the FY 1997 reflection seismic exploration survey. 5. Report on the FY 1997 No.2 test boring survey. 6. Summarization of the test on 'the new exploration technology of coal source' conducted between Japan and China. 7. Report on the drilling data measurement. 8. Various sections of the reflection seismic survey data processing. 9. Traverse line chart. 10. T3 isochrone chart. 11. T3 depth structural chart. 12. Report on the new exploration technology survey development (water area medium depth seam exploration) geological model making. (NEDO)

  5. FY 1982 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential supply amount of overseas resource (Survey of the potential supply amount of methanol); 1982 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Kaigai shigen kyokyu kano ryo chosa (Metanoru kyokyu kano ryo chosa) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-07-01

    For the study of the potential supply amount of methanol as power generation use fuel, survey was conducted as case study on the following: Victorian brown coal of Australia, conversion of Arun natural gas to methanol at site in Indonesia, political/social/technical restrictions, supply scale, economical efficiency, etc. at the time of the supply to Japan. For the calculation of economical efficiency, it was assumed that the scale of methanol production was 5,000 t/d, that the plant operated years were 20 and that the price of acquisition of raw material was US$4-10/t in Victorian brown coal and US$1-4/t in Arun natural gas. As a result of the study, in the case of natural gas base methanol, the CIF Japan is lower than CIF prices of LNG and crude oil in case the price of acquisition of raw material is US$1/t, but is higher than those in case the price is US$2/t. In the case of brown coal base methanol, it was found that the CIF Japan could not be lower than CIF prices of LNG and crude oil even in case the price of acquisition of raw material is US$4/t, which is the lowest. (NEDO)

  6. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

  7. Summarized report on fiscal 2000 basic survey for coal resource exploration. Survey for development of new exploration technology (Exploration of shallow layers on the land); 2000 nendo sekitan shigen kaihatsu kiso chosa hokokusho (yoyakuban). Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-01

    Efforts are made to develop a high-precision high-resolution seismic reflection method, high-efficiency method for measurement in the bored hole, coal potentiality assessment system, and so forth. For the development of the seismic reflection method, studies are conducted to properly deal with a situation where there are high-velocity layers at levels shallower than the object coal bed, and a conclusion is reached that quake generation based on the pseudorandom binary sequence code will be the best for the purpose. The system was tested for verification in a producing coal mine. As for measurement in the bored hole, an on-site test was conducted for a geophysical logging system capable of determining the total sulfur content, ash, and the like, and the system was found to supply high-quality data. In developing the coal potentiality assessment system, studies were made about the basic concept of the coordination of the system with the coal GIS (geographical information system) dealing with spatial data and about the functions of the system, and a conceptual design was prepared. (NEDO)

  8. Fiscal 1997 basic research on coal resource development (equipment development). Report on R and D of new exploration technology (exploration of medium-depth coal deposits in water areas); 1997 nendo sekitan shigen kaihatsu kiso chosa (kiki kaihatsu hen) hokokusho. Shintansa gijutsu chosa kaihatsu (suiiki chushindoso tansa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research result on development of new coal exploration technology. For a high-precision and high-resolution reflective seismic exploration system, R and D was made on the exploration technology of several meter in resolution for medium-depth (800m) coal deposits under a lake of 2m deep. As a result, the high-frequency and high-power source (150-200Hz in dominant frequency, 700-800m in penetrability) and the high-frequency and high sensitivity receiver (10-1000Hz in frequency band, 35V/PA in sensitivity) were developed successfully, and the positioning system was improved. The final evaluation of these elementary technologies was carried out through demonstration tests, resulting in satisfactory results. For a high-efficiency trial drilling system, the in-bore trouble prevention system for measurement, processing and analysis of drilling data (drilling length, drilling rate, revolution, bit load, torque) and drilling mud data (charge water pressure, charge/discharge water, density, pH, viscosity) was constructed. The outlook for low-cost measurement and a safety during drilling was thus obtained. (NEDO)

  9. FY 2000 report on the project on the researcher dispatch type international joint research survey. Survey of the internationalization of research on the effective utilization technology for energy resources; 2000 nendo kenkyusha hakengata kokusai kyodo kenkyu chosa jigyo hokokusho. Energy shigen yukoriyo gijutsu kenkyu kokusaika chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to themes of the research survey which contribute to upgrading/diversification of the effective utilization of energy resources and are important in increasing cooperative relations with overseas countries, survey research was conducted by dispatching investigators. Relating to long-life Si solar cells, research survey was made on the reduction in deterioration of solar cell. Concerning the hydrogen carbonless energy system, the economical efficiency of a natural energy/hydrogen combined system was studied for all areas of Aomori prefecture. About the development of the multiple chamber type artificial pancreas for patients with serious diabetes, study using model dogs was investigated. As to the processing of PVC waste, the mechano-chemical method was discussed in the U.S. The paper further surveyed the following: PDE application to the aerospace field, joint developmental study of the reuse type space transport system by Japan and Russia, treatment/recycling of the electric/electronic equipment waste including toxic substances, technology of the manufacture of nano-particles and evaluation of optical characteristics of nano-structures, etc. (NEDO)

  10. FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

  11. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  12. FY 1999 research cooperation project. Research cooperation in development of technology to extract/treat mineral resources in environmental harmony and high-efficiently; 1999 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is aimed at effectively using non-ferrous metal resource in Kazakhstan Republic and at conducting a joint development of the environment-friendly and efficient technology to extract/collect valuable metals (copper, gold, silver, rare metal, etc.) including in quantity in the slag generated with the mine operation in Kazakhstan. For the purpose of collecting valuable metals from slag, etc., the project is to develop the technology to collect valuable metals in saving energy and in low environmental loads by adopting the wet treatment process and to carry out the field survey on the existence of slag, etc. and the research on minerals. As the field research/domestic research, various element technologies are also to be carried out such as leaching, solvent extraction, electrolyte sampling, and waste water treatment. Based on the R and D of the element technology, a pilot plant is designed/fabricated and installed at the site in Kazakhstan. Then, the operation is studied and analyzed to make a technically/economically comprehensive evaluation. In this fiscal year, the field survey, research on the wet treatment, and test on the waste water treatment are conducted. Facilities of a pilot plant were transported to the site. (NEDO)

  13. Fiscal 2000 information collection/analysis project on basic research for coal resource exploitation. Research on technology of low-concentration methane gas recovery from underground coal mine; 2000 nendo sekitan shigen kaihatsu kiso chosa joho shushu kaiseki jigyo. Konaikutsu tanko ni okeru teinodo methane kaishu gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Technical trends were surveyed concerning the recovery and the use as fuel of low-concentration methane gas or the like contained in the air ventilated out of coal mines. Methane gas recovery technologies include high-temperature incinerators and catalytic incinerators designed to collect heat, method of conversion of methane to CO2 using microbes named methanotrophs, and adsorption methods using activated charcoal, zeolite, or the like. Among technologies that have reached a practical level in the utilization of mine methane gas, there are the temperature regenerative flow-reversal reactor (TFRR) and the catalytic flow-reversal reactor (CFRR) utilizing high-temperature oxidation reaction. TFRR has been reported effective by MEGTEC System after a 6-month operational test of a 3.0m{sup 3}/s plant at a British coal mine. Test and research are over with CFRR, which is now ready for a commercial scale verification test. Recovery by adsorption, though worth further research efforts, is economically away from commercialization at the present stage, and wants more studies of adsorbents, etc. (NEDO)

  14. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. Effective industrial utilization of livestock and fish waste containing keratin and collagen using bio-recycling technology; 1998 nendo Bio recycling gijutsu ni yoru shigen junkangata sangyo no sozo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for the bio-recycling technology, in order to produce the extracts and enzymatically hydrolyzed products from unutilized protein-containing resources, e.g., pig skin and fish scale. This paper summarizes the FY 1998 results. This project uses fish scale and pig skin containing collagen protein, and feather meal containing keratin protein, as the major feedstocks. High-molecular-weight collagen is extracted from the pig skin, and applied to production of cosmetics. It is concluded that the extract is safe to the human skin, and can be commercialized as a stock for cosmetics. A low-molecular-weight oligopeptide is produced from fish scale by enzymatic hydrolysis. It is concluded that the oligopeptide can be commercialized as a stock for health foods, because of its anti-radical activity and function of decreasing blood pressure. The R and D efforts are also directed to development of calcium apatite, recovered from the de-ashed liquid, as the Ca source for health foods, and development of peptide, recovered from feather meal by enzymatic hydrolysis, as a stock for foaming agent. (NEDO)

  15. Report on information collection and analysis for fundamental survey on coal resource development in fiscal 1998. Survey on coal supply potentiality in Bowen Basin in Australia; 1998 nendo sekitan shigen kaihatsu kiso chosa joho shushu kaiseki hokokusho. Goshu Bowen bonchi sekitan kyokyu potentiality chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was made on coal supply potentiality in Bowen Basin in Australia. The main coal beds exist in the order of four beds in the Permian period. The oldest bed is the Reids Dome bed in the Lower Permian period, deposited in the south-west part of the basin. The later wide-area transgression has caused the Back Creek bed groups to deposit, whereas three coal measures have deposited in a concave on the raised basic bed. Later, the ocean has invaded into the entire basin. After having turned into the Upper Permian period, regression had occurred from north to south, where major coal measures such as the Moranbah and German Creek beds had deposited over the entire basin. Further regression has taken place to south, causing three uppermost coal measures to have deposited over the entire basin. In major part of the areas identified currently with existence of coal measures, and even in areas without mines, the mining right or the exploration right has been established, limiting the areas having development potentiality. Five abandoned mining areas exist in the Rangal coal measure, two in the Moranbah coal measure, two in the Reids Dome coal measure, and one in the Baralaba coal measure. There is a possibility of discovering areas developable for a scale of several ten million tons. (NEDO)

  16. Report of FY 1997 on the international cooperation project. Survey of globalization of the effective energy resource utilization technology (development of high-accuracy acceleration measurement system); 1997 nendo kokusai kenkyu kyoryoku jigyo. Energy shigen yuko riyo gijutsu kenkyu kokusaika chosa (koseido kasokudo keisoku system no kaihatsu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report describes effectiveness of a system for measuring the acceleration and force in high accuracy by combining a laser interference meter and a vibration stand. A possibility of pressure sensitive paper to the impact force measurement in the collision examination is also described. The results obtained in FY 1997 are as follows. For the investigation of calibration system of acceleration and force sensor, one-dimensional interferometer system has been developed, which is standardized in ISO5347 accelerometer calibration. Thus, an interference fringe processing software has been made. Moreover, construction of a three-dimensional interferometer system has been started. For the characterization evaluation of pressure sensitive papers, it was succeeded in obtaining an elasticity wave pulse maximum about 1 msec by adopting the flight body made of resin. As a result, evaluation of the force sensor in the frequency area has become possible. To calculate the displacement of a body structural material in the collision experiment, an acceleration sensor has been made for trial purposes. For the international research cooperation, the working plan of a joint research with US Texas Christian University has been concluded. 11 refs., 73 figs., 23 tabs.

  17. Report on survey project for demonstration of warm sea water bathing facilities using unutilized resources such as wastes in islands by carbonizing them into energy; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Rito ni okeru haikibutsu tou mikatsuyo shigen no tanka energyka no kaisui on'yoku shisetsu heno jissho chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-05-01

    Surveys and discussions have been performed in Yuge Town in Ehime Prefecture for aiming at promotion of district development and zero emission in islands by carbonizing general wastes (household refuses and business operation wastes) and bamboos in the islands to utilize their energies as a substitute for the heat source of the warm sea water bathing facilities, as well as utilizing the produced carbides as soil improving materials or deodorants. The surveys were performed on bamboo carbonizing and gas carbonizing technologies, energy utilization feasibility, analysis of wastes composition, and identification of quantity of bamboos in existence. In discussing the energy utilization system by means of carbonization, it was revealed that the introduction of the bamboo carbonizing and gas carbonizing technologies can sufficiently satisfy the heat demand of the Yuge Town community facilities, although the amount of heat that can be supplied may vary because of difference in the technical processes. Also with regard to the problems of dioxins contained in the discharged gas and the problems of heavy metals contained in the carbides, it was discovered that different environmental criteria can be met as evidenced by the existing demonstration data. (NEDO)

  18. Report on the surveys in fiscal 1999 on the long term energy technology strategy investigations. Investigations on evaluation on impact of research and development investments, and optimal resource distribution; 1999 nendo choki energy gijutsu senryaku chosa hokokusho. Kenkyu kaihatsu toshi no impact hyoka oyobi saiteki shigen haibun ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper is a survey report for fiscal 1999 related to investigations on evaluation on impact (influential effect) of research and development investments, and on optimal resource distribution. First, a quantification analysis was performed on the impact imposed by the New Sunshine Project having been executed in the past. The analysis used as the base the regressive analysis between the project techno-stock (an index of the project budget amount depleted by a certain obsoletion rate after having been substantiated and aggregated) and the number of theses. In a case where time-series data can be obtained on the quantity of practical application, the regressive analysis was also performed between the number of theses and the quantity of practical application. A large number of projects are stimulating research and development activities of the subject themes of all about Japan. Some are imposing great influential effect on the practical application. In addition, it was found that emphasized and concentrated investment cases in the initial stage of a project have high influential effect. As a budget distribution pattern, the concentrated and emphasized investments in the initial stage of a project are more effective than investing dispersedly over an extended period of time. Suggestions were acquired on the future budget distribution. (NEDO)

  19. FY 1998 report on the results of the development of utilization technology of biological resources such as bioconsortia. Development of the bioconsortia system utilization/production technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the technology to use high grade functions of the bioconsortia system, the R and D were conducted, and the FY 1998 results were summed up. As to the study of functional material producing technology, screening of the 2400 strains owned by Marine Biotechnology Institute was conducted using reporter strain, and about 400 strains of homoserine lactone producing bacteria which are interbiological information convey substances were obtained. Concerning the effective decomposing/purifying technology of petroleum products, study of petroleum decomposition analysis technology was finished in the development of culture/control technology of petroleum decomposition microbial consortia constitutive bacteria. Relating to the analysis of the petroleum decomposition microbial consortia, changes in the bacteria population at the site of the heavy oil pollution accident on the Sea of Japan were investigated for the past one year by the PCR/DGGE method. It was found out that levels of the oil pollution in ocean could be assessed by measuring the concentration of Alcanivorax. As to the technology for highly utilizing unused petroleum fractions, conducted were the chemical analysis of photolytic crude oil, selection of the decomposition microbial consortia, etc. (NEDO)

  20. FY 1998 industrial technology R and D project. Report on the results of the development of utilization technology of biological resource such bioconsortia system (Development of production technology of biological use petroleum substituting fuels); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Technology development was conducted for production of useful substances using the bioconsortia system. In FY 1998, the development of element technology was studied. As to the utilization technology of gut symbiotic microorganisms such as termite and longhorn beetle, clone types of gut microorganism complex system were analyzed to find out the diversification. In the decay of wood, co-culture of two species of mold fungus was increased in efficiency than single culture. More than 90% was classified/identified of the mold fungi accumulated (in wood piece)/separated for the utilization of plant symbiotic microorganisms. For the production of petroleum substituting useful resource, conditions were established of callus induction from immature embryos of tropical oil crops, especially oil palm, and of regeneration of a lot of small plants from the callus. To establish the Agrobacterium-mediated transformation system of oil palm, the binary vector harboring the reporter gene and selectable marker gene was constructed. Using the vector, oil palm tissues are inoculated and infected with agrobacteria. To heighten the function of palm oil, 10 particular clones were selected from the complementary DNA library obtained from oil palm fruit tissues. The genetic study of germs was also made. (NEDO)

  1. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  2. Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

  3. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

  4. Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

  5. Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

  6. Research report for fiscal 1998. Comprehensive research cooperation on environmental technologies (study of air pollution monitoring at model industrial estate in Thailand); 1998 nendo chosa hokokusho. Kankyo gijutsu sogo kenkyu kyoryoku (Taikoku model kogyo danchi taiki osen monitoring ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Cooperative studies are conducted for the improvement of technologies for preventing air pollution caused by SOx, NOx, volatile organic compounds, etc., discharged into the air by mills and factories. For the measurement of air pollution, instruments capable of automatic and uninterrupted measurement of SOx, NOx, and suspended particle matters are installed at Map Ta Phut Industrial Estate, and measurement is carried out. Volatile organic compounds are measured and analyzed along the borderline enclosing the estate. The amounts of SOx and NOx emitted by automobiles, ships, etc., are calculated. An air pollutant diffusion simulating model is built, into which data about pollution sources and weather are inputted for the calculation of SOx and NOx concentration levels at the industrial estate as is. Technologies are transferred to Thai researchers and engineers, which involve the use of instruments for the measurement of pollution levels in the environment and for the observation of weather conditions, the techniques of sampling and analysis, the construction of atmosphere simulating models, and the analysis and evaluation of the existing air pollution. (NEDO)

  7. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  8. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 1. Research study on integrated evaluation and development plan; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on the WE-NET project in fiscal 1996. The WE-NET project is composed of various elemental technologies such as hydrogen production, transport, storage, low-temperature material, utilization and hydrogen combustion turbine. The organic integrated cooperation and coordination between individual subtasks are indispensable for effective promotion of the project and optimization of the total system. The current R and D states of every elemental technology were surveyed, and its findings were utilized for coordination of the whole project and examination of the research project including pilot studies. Eleven important items in the total coordination including a total system cost and safety measures in a developmental stage were examined. The development results for 4 years of fiscal 1993-1996 were assessed together, and the draft working plan for fiscal 1997-1998 was also decided. The verification test plan of a hydrogen combustion turbine scheduled in Phase II was studied, and the basic plans of development step were proposed. The draft report of a transition scenario was also prepared. 6 figs., 68 tabs.

  9. General report on the results of the development of fuel cell technology such as urban energy center. Evaluation study of life of phosphoric acid fuel cells (fiscal 1995 and 1996); Toshi energy center nado nenryo denchi gijutsu kaihatsu kenkyu seika sogo hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu (1995 kara 1996 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Receiving subsidies from MITI, NEDO carried out this project in fiscal 1995 and 1996 as a joint research with Technology Research Association for Phosphoric Acid Fuel Cell Power Generation System and others. The project aimed at developing the accelerated test method which can evaluate in a short time the cell life of phosphoric acid fuel cells (PAFC) and the lowering of characteristics. The accelerated test method of PAFC life is thought to be a tool indispensable for the promotion of commercialization, but the accelerated test method like the usual material evaluation has not yet been established. To solve this problem, procedures were developed to rationally plan the accelerated test on short stacks of full scale based on the small cell test data. Here, to rationally estimate the operational state under actual conditions based on the data on the accelerated test, it is necessary to fully understand the mechanism of deterioration of PAFC. By conducting in parallel the element study for the basic elucidation of cell deterioration phenomena, obtained was the useful information/knowledge which back up the results of the accelerated test scientifically. 168 figs., 33 tabs.

  10. Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

  11. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

  12. Fiscal 1997 report on the results of the cooperative research project under consignment from NEDO on technology for simply setting-up of the molding conditions of engineering plastics; 1997 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (Engineering plastic no seikei joken kan`i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A cooperative research project was carried out between Japan and Thailand with the aim of developing a system which can simply set up molding conditions using as elements the technology on mold design and injection molding in plastic parts production and the experiment/evaluation technology for making sure of the quality of molded products. In fiscal 1997, based on the basic plan worked out in the previous fiscal year, molding equipment, auxiliary equipment, mold, experimental equipment, injection molding CEA system, etc. were installed at Thailand`s BSID (Bureau of Supporting Industries Development). Supported by equipment manufacturers, the technical guidance was given for operation/maintenance/control of all equipment. At the same time, researchers were sent from Japan, and the joint research was started. Japan received three researchers from BSID for training of molding technology, injection molding CEA program use technology, and experimental evaluation technology. The engineering plastics used for study are polyacetal, polyamide and polycarbonate. 17 refs., 68 figs., 14 tabs.

  13. FY 2000 report on the survey of the calculation of the overall conversion efficiency in case of using natural gas for fuel cells, etc.; 2000 nendo chosa hokokusho. Tennengas wo nenryodenchi ni mochiita baai no sogo henkan koritsu no santei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of evaluating the efficiency of fuel cell including the fuel supply system, survey was made of drilling of gas resource, conversion to liquid base fuel, transportation, storage, etc., the energy conversion efficiency was studied considering reforming characteristics of various fuels. In the comparison between LNG, methanol, DME and GTL that originate in natural gas and LPG and naphtha that originate in oil, a big difference is that methanol, DME and GTL were made through the conversion process with the large energy consumption. Namely, by the time before the reforming into hydrogen, the oil base indicated a higher efficiency in secondary energy fuel production than the natural gas base. Further, the reforming efficiency is the highest in methanol and DME, and there is a little difference between the integrated fuel cell (normal pressure) and the hydrogen production use fuel cell (pressurized). Concerning city gas and GTL, the efficiency is lower, affected by S/C. The overall efficiency is determined considering the conversion efficiency in other stages since it is determined by the conversion efficiency of up to the raw fuel and the energy conversion efficiency at PEFC. (NEDO)

  14. Fiscal 1999 technical research report. Development project on prompt-effect international standards for developing new industry (Comprehensive survey and research concerning promotion of international standardization); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For encouraging the promotion of international standardization involving the six subjects of advanced technology taken up under the above-named project, wide-range investigations are conducted into measures for international standardization, the activities of international standardizing agencies and organizations, and the approaches of European and American business corporations to this issue. Technical literature and material are studied in Japan, and interviews are held overseas with responsible persons at organizations and corporations engaged in this task. At Standards Development Organization (SDO) of America, verification tests are under way for early development into international standards of technical standards it has so far developed independently. For the strategical utilization of intellectual property incorporated into its technical standards, SDO accepts that the best policy is to win approvals from patent proprietors at the early stage of standardization process by presenting them with conditions about patent implementation. In Europe and America, for the enhancement of their competitive power in the international theater, governments and civil sectors cooperate with each other for the establishment of international standards and, in business corporations, the management takes the initiative in coping with the issue with an understanding that there are business opportunities in international standardization. (NEDO)

  15. Joint research report of Central Research Institute of Electric Power Industry and Japan Research Institute Ltd. Conceptual construction of Japanese type end-use model; Denryoku chuo kenkyusho Nihon Sogo Kenkyusho kyodo kenkyu hokokusho. Nippon gata end use model no gainen kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    The concept of Japanese type demand analysis model (end-use model) was constructed for the efficient management of electric power companies and efficient power utilization. Diffusion and use conditions of domestic air conditioners are considerably different depending on local life style and climate. In order to design demand measures considering combination of appliances in every market segment, demands in an end use level (end demand level, each appliance level) should be acquired. The basic structure of the model is composed of various exogenous variables such as weather data, price and ups and downs trend of customers, and various appliance data such as size, efficiency and energy consumption rate, and various customer data such as possession rate of appliances and number of customers. The final energy demand is estimated by integrating the above variables. By systematizing the stored data of precise actual load conditions, construction of DSM (demand side management) strategy becomes possible by using computer tools. 8 refs., 15 figs., 13 tabs.

  16. FY 1999 report on the results of the study of the generative utilization basement technology of environmental friendly type metal base materials. Element/comprehensive process study; 1999 nendo kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu seika hokokusho. Yoso sogo process kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D have been conducted since FY 1991 on the process in which scraps can be used with no reduction energy required in iron-making stage, and the results of FY 1999, the final fiscal year, were summarized. In the assessment study of the comprehensive system, a full scale of experiment was carried out of the experimental plant which was completed in March 1998. In this fiscal year, experiment was conducted on converter type and fixed bed type as preheating/melting method. As a result, the energy unit requirement, productivity, etc. which were targeted at first were obtained, and the experimental results expected at first were obtained on scrap preheating/melting technology/exhaust gas treatment. Moreover, the FS using the actual system was conducted, and the following conclusions were acquired: melting use primary energy decreased by more than 25% from that in the existing electric furnace; it is possible to arbitrarily select power loads at 80%-30% the same as those in the existing furnace; new melting method is more excellent in primary energy reduction than in advanced electric furnace as of FY 1999; it is possible to reduce primary energy by 25% also in the case of operating iron-melting in converter type and shaft type. (NEDO)

  17. Report on achievements in fiscal 1988 on research and development of the photoreactive materials under the next generation basic technology research and development project. Comprehensive surveys and researches on photoreactive materials; 1988 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokuksho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1988 on comprehensive surveys on photoreractive materials. Based on the research and development institution for the next generation basic technology under the initiative of the Agency of Industrial Science and Technology, development is being promoted on photoreactive materials, or photochromic materials and photochemical hole burning (PHB) materials (materials in which molecular structures and assembly state can be changed reversely by actions of light, leading to expectation of application thereof to ultra-high density recording, displays at high resolution, and light switches). In order to achieve smooth and efficient promotion of the development thereof, development of the related technologies inside and outside the country was surveyed and discussed. Comprehensive surveys and researches were also carried out on the common basic technologies by looking to the well-informed people for guidance on the research. This fiscal year has held joint committee meetings to which lecturers were invited to discuss respective problems in the research and development trends. In addition, as the domestic survey, the status of research and development at the Tsukuba University was surveyed on photo-responsive polymeric gels. Furthermore, as the survey on the overseas technological trends, information related to photoreactive materials was collected mainly on photochemical burning materials in the U.S.A., and the research trends were surveyed. (NEDO)

  18. FY 1991 report on the results of the surveys on the technologies for forming composite materials. Research and development of the new technologies for forming composite materials (Comprehensive surveys and researches); 1991 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This project is aimed at development of new technologies for forming composite materials by studying the methods for controlling structures of ceramic- and metal-based composite materials, and also at development of the technologies for forming near-net shapes utilizing the phenomenon of superplasticity. The literature survey is conducted to help promote the developments, and the abstracts of the major papers are pigeonholed into 4 general categories; (1) production and properties of ceramic-based composite materials, (2) superplasticity of ceramic-based composite materials, (3) production and properties of metal-based composite materials, and (4) superplasticity of metal-based composite materials. This paper summarizes the abstract of these papers. The category (1) includes carbon fiber reinforced Sialon composites produced by polymer pyrolysis, the category (2) includes superplasticity of functional ceramics, and comparison of tensile and compressive creep behavior of a superplastic yttria-stabilized zirconia-20 wt.% alumina composite, the category (3) includes in-situ metal matrix composite, and the category (4) includes high strain rate superplasticity in whisker-reinforced alumina composites, and application of superplasticity to fabrication of metal matrix composites. (NEDO)

  19. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Comprehensive research and development for reducing ABS (MABS) sensor system into small module for enhancing vehicle steering safety; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Koji no sharyo soansei wo jitsugensuru ABS (MABS) sensor system no kogata module ka ni tsuite no sogo kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The effort aims to develop a sensor system to enable overall VDC (vehicle dynamic control). The goal is to manufacture a small module type sensor system more than 20 times higher than the conventional type in responding speed and accuracy, which will use a novel ABS (anti-lock braking system) capable of direct and real-time measurement of axial forces in the four directions. The prototype module will be a package in which a system-on-a-chip accommodating peripheral circuits is integrated with a sensor. In the effort to develop a novel multi-axial sensing system (MASS) for a smaller ABS, a circuit optimization technology was developed. A dedicated IC (integrated circuit) was developed for a system to process a large volume of signals. In the effort to develop technologies for packaging the novel sensor system and for constructing modules, technologies were developed for integrating sensor components and an IC into one, module junctioning, module installation, simplification of the installation process, and for the manufacturing of modules. Developed in the effort to optimize MASS were technologies involving the selection and evaluation of sensor components and the enhancement of such processes, optimization of the sensor itself, and the improvement of the sensor system for higher efficiency in calculation. Sensor modules were tested aboard vehicles and the compatibility of the system-on-a-chip with the MASS module was confirmed. (NEDO)

  20. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

  1. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  2. FY 1992 Survey report of the technologies for creating/processing advanced biomaterials. Research and development of the technologies for creating/processing advanced biomaterials (Comprehensive survey and research); 1992 nendo senshin bio zairyo no sosei kako gijutsu chosa hokokusho. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, item (6) peptide having activity with plant, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  3. Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

  4. Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 1. Survey/research for the comprehensive evaluation and developmental plan; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The paper described the results of the FY 1998 WE-NET project survey. WE-NET is composed of various element technologies such as hydrogen production, hydrogen transportation, storage technology, low-temperature materials, hydrogen utilization, and hydrogen combustion turbine technology. Therefore, considering the effectiveness as a total system, it is extremely important to traversally evaluate the situation of the R and D of each technology and developmental achievements and to work out developmental plans with integration, considering the effectiveness as a total system. From viewpoints of making effective promotion of the project and attempting optimization as a total system, it is necessary to make organic/comprehensive connection and adjustment among individual subtasks all the time. In this survey/research, in the case of proceeding with the above-mentioned studies, a committee having knowledgeable persons and learned persons as members was established. There, an investigational study was conducted over the whole WE-NET structural technology, and at the same time the following were attempted: the constant/mobile comprehensive adjustment of the whole project, evaluation of the developmental results, and optimization of the developmental plans. The results obtained in 6 years of Period I were evaluated traversally and comprehensively, and how to proceed with the development in Period II was proposed, which showed the developmental continuity. (NEDO)

  5. FY 1999 project on the development of new industry support type international standards. Standardization for securing mutual connection among informative household electric appliances; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted with the aim of the international standardization for securing mutual connection among informative household electric appliances, and the FY 1999 results were summarized. In FY 1999, the following were conducted: trial manufacture (for mass production) and evaluation of wide band POF (plastic optical fiber), trial manufacture and evaluation of home use small connector, and trial manufacture and evaluation of optical transceiver module. Various data required for the targeted standardization (transmission band: S400 or more, transmission distance: 100m) were obtained. In the next fiscal year, tests to demonstrate validity/reliability of the data are conducted so that the standards to be accepted as an international standard can be established. In the study of strategies of international standardization, the contents of the standards proposed were discussed, and activities of IEC/TC100 (multi-media) and the related TC were investigated. Early in the next fiscal year, the TC to be proposed is fixed, and international proposing activities are started such as the introduction of the standardization for this R and D to the organizations and persons concerned overseas. (NEDO)

  6. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

  7. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

  8. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  9. Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

  10. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 2: Collected data); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 2 (shiryoshu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    As to the survey of the existence amount of geothermal resource in the Akinomiya area, Ogachi town, Akita prefecture, which was made in FY 1999, the comprehensive analysis was conducted, and the data were arranged. In relation to the surface survey, data on the following were described: geological survey, supplementary surface geological survey, soil gas survey, precision gravity survey, supplementary gravity survey and 3D model re-analysis, electromagnetic survey, etc. With relation to the well survey, data on the following: wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, N9-AY-5, N10-AY-6, N10-AY-7 and N10-AY-8, survey of cores of existing wells, temperature/pressure logging of wells remaining stationary after having been left long, sampler logging, etc. In relation to the jetting test, data on the short-term jetting test on wells of N8-AY-1, N8-AY-2, N9-AY-3, N9-AY-4, etc. With relation to the evaluation of reservoirs, data on the pressure monitoring, results of the reservoir simulation, etc. (NEDO)

  11. FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

  12. FY 1997 report on the survey on the current residential waste treatment and integrated utilization of waste including heat supply in Shanghai city; 1997 nendo chosa hokokusho (Shanghai shi ni okeru seikatsu gomi shori no genjo narabini kyonetsunado wo fukumu sogo riyo ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Survey was made on residential waste treatment in Shanghai city. Shanghai city with nearly 13 million registered residents produces on average 10,000-11,000 tons/day residential solid wastes. Such wastes are basically disposed by land filling. A landfill site has a current disposal capacity of 7,500 tons/day, and is scheduled to be expanded up to 9,000 tons/day. Problems of waste disposal in Shanghai city are as follows: transportation of wastes collected in the city by trucks, transportation through transit stations to the landfill site by ships, and high disposal cost. Shanghai Environmental Sanitation Bureau is pursuing researches on recycling of wastes, reduction of wastes and harmless treatment in place of conventional land filling. As the survey result, adoption of complete separate collection of wastes is basically important, and application of the latest technologies such as combustion treatment for every waste, heat use, gasification fusion furnace, and RDF (refuse derived fuel) for coal-firing boilers should be considered. 86 figs., 18 tabs.

  13. Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

  14. Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (Second volume: comprehensive investigation and research); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho (sogo chosa kenkyu). 2. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Technology was developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation was introduced, and by fixing the peptides to the surface of a base plate such as silica glass or modifying the surface with them. As the related technological investigation, the following six areas were surveyed. (1) Structural design of peptides, (2) synthesis of peptides by chemical and enzyme methods, (3) synthesis of non-natural amino acid and its introduction into peptides, (4) structural analysis of peptides, (5) physiological activity of peptides, and (6) materialization and functional manifestation of peptides. With the exception of the area (5) consisting of one advanced research case, other areas were constituted of analysis, general remarks and research cases. The area (6) was constituted of materialization technique 1 and 2, film function and peptide, catalytic action 1 and 2, and one research case; the materialization technique was defined as a technique for modifying the surface of a synthetic resin, metallic or silica glass substrate with functional peptides; and an explanation was given to the present state of the fixation, pattern formation and integration technologies. (NEDO)

  15. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

  16. Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

  17. FY 1999 report on the comprehensive analysis of the geothermal development promotion survey. Forth. No.C-3 Akinomiya area (Separate volume 1: Forth survey); 1999 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No. C-3 Akinomiya chiiki (Dai 4 ji) - Bessatsu 1 (Dai 4 ji chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    The paper reported the results of the long-term jetting test, etc. which were carried out as the forth survey of the geothermal development promotion survey in the Akinomiya area, Ogachi town, Akita prefecture. The jetting induction and the situation of production/reduction were described as follows. N9-AY-3 began to well spontaneously after being induced by sending air up to wellhead pressure of 4.8 MpaG. Damping was recognized for a month or so after the start of jetting. After that, however, no damping was recognized, nor was recognized the deterioration of the fluid enthalpy with age. The pH of geothermal water was definite, approximately 8, and the electric conductivity and Cl concentration were 8,500 {mu}S/cm and 2,600 mg/L, respectively. The maximum jetting capacity of N10-AY-8 was 10.4t/h in steam and 8.9t/h in geothermal water at wellhead pressure of 0.24 MPaG, and after that, it showed a tendency to lower. The flow rate of reduction of N8-AY-1 changed from 80-90t/h at the beginning to 60-70t/h. With the continued reduction, the lowering of reduction capacity was recognized. In the test, the following were carried out: temperature/pressure/spinner logging, test on pressure transition, survey of fluid properties, survey of jetting microseisms, etc. (NEDO)

  18. FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

  19. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  20. Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Comprehensive survey); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (sogo chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveys and studies were conducted to facilitate and invigorate research, development, and economic activities and to provide technology related intellectual assets in an organized, systematic way. In the survey related to the buildup of intellectual infrastructures, questionnaires were sent to 789 organizations in the industrial and academic domains concerning measuring standards, reference materials, base for information on biological resources, base for safety management of chemical substances, base relating to human life and welfare, and base of knowledge relating to materials. On-site surveys were also conducted in Asia, Australia, North America, and Europe. Concerning 10 inorganic reference solutions whose development is urged because they are related to environments, raw materials for them were selected, required purity levels were defined, and methods for measurement and evaluation of safety when in prolonged preservation were investigated. Conducted in the research and development of individual subjects were database buildup on thermophysical properties, research into long-term durability of heat-resistant composite materials, research into textural structure and characteristics as materials of sintered bodies of fine ceramics, database buildup on the safety of non-ferrous metals, studies of base of human characteristics measurement, and the like. (NEDO)

  1. FY 1989 report on the results of the next generation industrial basement technology R and D project - R and D of photo-reactive materials. Comprehensive investigational research on photo-reactive materials; 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    As to photochromic materials and photochemical hole burning (PHB) materials, for the purpose of smoothly/efficiently promoting the R and D, the common basic technology was comprehensively surveyed as well as survey/study of the related technology development in Japan and abroad. In FY 1889, a joint committee was held, and a meeting was held of lectures given by lecturers from outside on the following: reversible response LB multilayered film and 2D optical switching element, photochemical HB and solid polymer, photovoltaic excitation dynamics of polymer solid, wavelength variable/semiconducting laser, optical memory, etc. A meeting for study/discussion on the details was also held. Items for the meeting were as follows: optical orientation control of nematic liquid crystal by photochromic surface, design of photochromic molecules, molecular movement and photo-reactivity in molecular aggregation system matrices, PHB spectra and mesoscopic structure control, continuous HB using semiconducting laser and sub-picosecond photon echo, quinone system derivative PHB in polymer matrices, etc. (NEDO)

  2. General report of entrustment investigation for demonstration tests of turnover from oil to methanol in the thermal power plants in fiscal 1995. Total assessment of methanol using power generation technology; 1995 nendo sekiyu karyoku hatsudensho methanol tenkan nado jissho shiken itaku gyomu hokokusho sokatsu hokokusho. Methanol riyo hatsuden gijutsu sogo hyoka chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To promote the introduction of methanol fuel into the thermal power plants, total assessment was provided. For calculating the methanol production cost, the plant was assumed to be constructed in the Southeast Asia or Middle East. Two methods, i.e., steam reforming and gaseous phase fluid methods, were investigated. Since the price of natural gas is low in the Middle East, the methanol production cost by the gaseous phase fluid method is estimated to be about 1.5 yen per thousand kcal. The transportation cost can be reduced into one-half to one-third of current cost using a large-scale tanker. Although the heating value of methanol per weight is lower than that of LNG, the volume flow of methanol is similar to that of LNG due to its low specific gravity. Conceptual designs were conducted for some power generation systems, such as gas turbine of combined cycle, diesel engine, and fuel cell. The power generation cost was estimated to be 8 to 9 yen per kWh, which depends on the receiving price of methanol. It is nearly equivalent to that of LNG combined cycle power generation. There are no problems of air pollution and ash disposal. When considering the long-term security of energy sources, the use of methanol would be one of the selections as utilization of natural gas. 6 refs., 33 figs., 25 tabs.

  3. Report on the research and development under a consignment from NEDO of high temperature carbon dioxide fixation and utilization technology for fiscal 1996; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku gyomu seika hokokusho. Nisanka tanso koon bunri kaishu sairiyo gijutsu kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the prevention of global warming, this R and D is aimed at separating/recovering high temperature CO2 from high temperature gas at 300degC or above and developing technology for effective use of the recovered CO2 as measures taken for reduction in CO2 emissions from the fixed emission sources. In this fiscal year, the following were proceeded with: heightening of separation performance evaluation technology, promotion of technical development of ceramic separation membranes and supports, and development of element technology of modular integration. In the examinational research on separation technology and system optimization, the following were conducted: survey of trends of the technical development, conceptual design of plant and prediction of process behavior, assessment of applicability of the process, and study of effects of utilization/spread of the developmental technology. In the former R and D, borosilicate glass powder rich in alkali is formed on the ring by joining the trially manufactured hollow fiber type membrane and the same form alumina cylinder, and sealing property and strength which stand measurement of permeability were confirmed. In the latter, an innovative process applied with CO2 high temperature separation technology was studied to examine effects of the spread of high temperature gas separation technology. 403 refs., 478 figs., 134 tabs.

  4. Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for enhanced interoperability between optical disk systems; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out for the enhancement of logical format-based interoperability between optical disk systems for the purpose of presenting propositions for international standards. That is, UDF (universal disk format) defined by OSTA (Optical Storage Technology Association) was taken up against the volume/file structure defined by ISO/IEC13346, and efforts were exerted to substantiate environments for its compatibility test and to develop specifications to achieve such enhanced interoperability. In this fiscal year, specifications were drafted for application program interfaces for the UDF-based file system and UDF security augmentation. These would be presented to IEC (International Electrotechnical Commission) and OSTA, respectively. Their Japanese versions were submitted to the Ministry of Economy, Trade and Industry of Japan, for publication as standard-related information. Maintenance of UAF (universal accessible file) system-compliance test tools were accomplished in response to user requirements and to the updating of UDF-compliance test disk specification. (NEDO)

  5. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  6. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  7. Fiscal 1997 report on the results of the international standardization R and D. System to make comprehensive evaluation of potential health effects of next generation image media; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Jisedai media seitai eikyo sogo hyoka system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper proposed the international standardization for the use of next generation image media by evaluating health effects of the use of next generation image media such as head mounted display and 3D monitor. A method to comprehensively evaluate health effects was studied with the design friendly to humans and standardization on safety as final targets. Themes were divided into the autonomous nervous system and the measuring system. The development was carried out of a method to evaluate the autonomous nervous function by the dynamic state of blood circulation and pupillary reflex as well as the development of portable sphygmomanometer and pupillometer. Using these developmental instruments and conventional instruments, measurement was made of blood pressure, cardiac output, respiration, pupil size, eyeball movement and focus accommodation. A possibility was suggested of obtaining the uniform elucidation also in case analytical changes of individual parameters cannot be extracted or consistency cannot be seen in the course of changes. The paper determined basic standards for the experimental use stereoscopic image, made measuring use 3D images, and collected realtime data by the overall simultaneous measuring system constructed. 109 refs., 166 figs., 18 tabs.

  8. Report on the achievements in the Sunshine Project. A comprehensive report on development of coal liquefaction technologies and a performance test on Chinese coal liquefaction (fiscals 1981 through 1987); Sekitan ekika gijutsu kaihatsu seika hokokusho. Chugokutan ekika seino shiken sogo hokokusho (1981 nendo kara 1987 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The present Japan-China joint development project is intended to study liquefaction performance of different types of Chinese coals, select coal types suitable for coal liquefaction, and serve for enhancement in the coal liquefaction technologies employed by the Chinese side. Since a small continuous testing device has been installed in fiscal 1982 and begun with the trial operation in March 1983, the liquefaction test has been performed for about five years, and is scheduled to continue another three years. Chinese coals produced in seven provinces and two autonomous regions have been subjected to the coal type selection, on which discussions were given for liquefying reaction characteristics by using autoclave testing and small continuous testing devices. As a result, circulation tests were performed by the end of fiscal 1987 on five coal types, namely Beisu coal, Texgxian coal, Xianfeng coal, Shenmu coal, and Meihekou coal. Data were acquired during the circulation and at the equilibrium. Comparison of the results of tests on these five coal types with the results having been acquired from the 0.1-t/d BSU in Japan before modification verified the result being nearly reasonable. (NEDO)

  9. FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

  10. Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

  11. FY 1999 project on the development of new industry support type international standards. Comprehensive survey research on the promotion of international standardization; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of promoting the international standardization effectively/strategically, a comprehensive survey was made, and the FY 1999 results were summarized. In the trend survey on the comprehensive international standardization, survey was conducted for companies in the material field (plastics, rubber and iron steel) and in the mechanical field (robot, machinery, aircraft, etc.). As a result of the survey, it was found out that they have few headquarters systems and experts, but they tackle it strategically and defensively, taking the standardization as business. Also as to the trend of CEN/CENELEC, importance of the continued trend survey was pointed out. In the survey of policy for the international standardization, survey was carried out on the trend of the process for working out the international standards (TS, ITS and SDO). Further, in relation to the technology standards and intellectual property rights in the hi-tech field, survey was made on the present situation of rules for handling intellectual property rights of organizations, groups, etc. for standardization, how to handle intellectual property rights in the standardization process, problems and the solution, etc. (NEDO)

  12. Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

  13. Report on a survey for promotion of geothermal development and an overall analysis of areas in fiscal 1996. Report No.C-3 for the Akinomiya area (First analysis); 1996 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho. No.C-3 (Akinomiya chiiki dai 1 ji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This paper summarizes the result of a survey for promotion of geothermal development and an overall analysis of the Akinomiya area in fiscal 1996. The subject area is located in Katsuo Town in south of Akita Prefecture. The geothermal reservoirs are regulated by the irregular construction created by upheaval and subsidence of the pre-Tertiary basement rocks. The underground temperature construction shows the temperatures rising toward Mt. Yamabushi. The latest geothermal activities should have taken place after the eruption of Mt. Takamatsu. The geothermal activities near the Arayu area have been most active until recently, and is still predominant. Transformation activities were active in the former period of the Pleistocene era. The acidic transformation band has been active after sedimentation of andesites in Mt. Takamatsu thereafter, which should have been active not only in areas where it is now active on the ground surface, but also in greatly wider areas. Geothermal fluid flows being regulated by faults, whereas fractures with high permeability existing along the faults are suitable for developing steam collection. Hot spring waters were produced by the geothermal fluid having risen along the faults and been mixed with and diluted by ground surface water near the ground surface. Areas promising for geothermal development would spread over the areas with high permeability along structural lines such as faults which show the convection type temperature pattern and temperatures higher than 250 degrees C. (NEDO)

  14. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  15. FY 2000 research cooperation project on the comprehensive research cooperation for environmental technology. Research cooperation for technology for prevention of the water pollution caused by plant waste water in Vietnam; 2000 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku (Betonamu koku kojo haisui ni yoru suishitsu osen boshi taisaku gijutsu ni kansuru kenkyu hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of increasing the research capability of the Center for Consultancy, Training and Technology Transfer in Vietnam, research cooperation for prevention of water pollution was given for plants of the local industry located in the suburbs of Hanoi city. In the survey of the actual state of the water pollution in the industrial area in the suburbs of Hanoi city, the following was found out: In the area, approximately 110 companies of the production industry such as livestock feed, papermaking, dyeing, brewing, construction materials, etc. are in operation and are discharging the untreated waste water into rivers and waterways because waste water treatment facilities are not prepared yet. In this research cooperation, the following were carried out: detailed survey of specified plants and proposal for improvement, training of Vietnamese researchers/engineers in charge of water pollution prevention technology, invitation to/training at Japan of Vietnamese managers/researchers, seminar to be held on the site, equipment to be given that is needed to measure water quality. The equipment to be given is a portable multi-item water quality meter and analytical equipment such as spectrometer, atomic absorption spectrophotometer and gas chromatograph. (NEDO)

  16. Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

  17. Fiscal 1997 report under consignment from NEDO on photon measuring/processing technology (development of power generation facility use high-function maintenance technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A research/development was conducted on technologies of photon applied measuring/photon applied processing/photon generation which are usable for heightening of reliability and maintenance efficiency of power generation facilities. In fiscal 1997, high melting-point metal particles were manufactured by high energy density laser for formation of high temperature and stabilized fine functional circuit. Further, a wavelength changeable ultra red laser light source was studied which can make in-situ measurement of gas concentration and components. A study was also made to examine the surface composition by measuring fluorescent X-rays emitted by radiating high intensity laser beam on the surface of material. A rod type and a slab type as a high-output complete-solidified laser are under development. There is also a development aiming at high speed/high quality photon processing such as high speed/high precision welding/cutting and laser joining. Besides, a study is being made of high energy pulse/high quality beam complete-solidified laser. The paper made a comprehensive survey of the trend of the photon measuring/monitoring technology, and made a systematical arrangement of the developmental subjects extracted. 142 refs., 357 figs., 62 tabs.

  18. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of environmental technology such as recycling (for public). 1; 1996 nendo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Recycle nado kankyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo). 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This R and D is aimed at promoting reduction in environmental loads by waste, etc. and reutilization of waste, etc., and at developing environmental technology such as recycling contributing to reducing road traffic noise. Studies were made on operation conditions of material separation in the bottle state and flake state, color separation, washing process, etc. Moreover, tests were conducted on comparisons of performance of shredders with different functions. Running tests of 100,000 times were conducted to confirm effectiveness of durability of the paved road with used papers. Measurement of hardness of the resin using the sol-gel method and coating experiment using organic dye were carried out to study the membrane effect speed and flaw resistance of coating of coloring bottles. Gasification of shredder dust and separation of nonferrous metal and glass were conducted to get the basic data. As to FRP bath tubs, the ratio of glass fiber and plastics was studied and western tiles were trially manufactured. Further studies were made of removal conditions of noncombustibles, chlorine and sulfur content, and reaction conditions of alkali additives including kind, quantity and addition method. 166 figs., 132 tabs.

  19. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

  20. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  1. The Japanese approach to financing LNG projects

    International Nuclear Information System (INIS)

    Aoki, Wataru

    1995-01-01

    The Japanese approach approach to financing LNG project has been what could be called a combined purchase and finance system which has been arranged mainly at the initiative of japan's Sogo Shosh (general trading companies) with the support of japanese governmental financial agencies and a purchase commitment from japanese utilities. In the QATARGAS project, despite it being the first greenfield LNG project in decade since North West Shelf Australia LNG project, financing for the LNG plant phase has been successfully arranged through Japanese financing. The structuring of the financial facilities for the QATARGAS project seems to have lessons for future development of the next generation of greenfield LNG projects. Discharge of the parties' liability, proper sharing of the risk burden and reconfirmation of the spirit of mutual understanding and trust among the parties concerned are key factors for the success of any new LNG project in the future. (Author)

  2. FY 1983 report on the results of the verification test on the methanol conversion for oil-fired power plant. Survey of the potential supply amount of overseas resource - Survey of methanol usability (Conceptual design of methanol reformed gas turbine); 1983 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken kaigai shigen kyokyu kano ryo chosa (Metanoru riyo kanosei chosa) - Metanoru kaishitsu gata gastabin no gainen sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    For the purpose of using methanol as power generation use fuel, the paper carried out of the conceptual design of methanol reformed high efficiency gas turbine and the evaluation study of economical efficiency. The methanol reformed gas turbine is to recover the heat from turbine flue gas and to improve thermal efficiency by using the fact that the vapor reforming reaction or decomposition reaction of methanol advance endothermicly at low temperature between 250 and 350 degrees C. It was judged that the combination with the existing technology made the practical application possible and that it was appropriate to adopt the regenerative gas turbine/water-injection and reforming (RGGT/WI and R). As a result of the trial calculation of construction cost of RGGT/WI and R and calculation of power generation cost, RGGT/WI and R became more profitable than the simple open gas turbine at a capacity ratio of 10% or more, and became more profitable than the combined cycle at all capacity ratios. In the use of RGGT/WI and R, which uses methanol as fuel, SOx is not included in flue gas, and the NOx included is estimated at 35ppm or so. The amount satisfies the standard according to the boiler using fluid as fuel. (NEDO)

  3. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

  4. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use of unused hydrocarbon resource, technology for development of environmental harmony type catalyst); 1995 nendo kokusai kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kankyo chowagata shokubai kaihatsu gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) technology for development of environmental harmony type catalyst. In 1), a survey was conducted of applicability of biological surfactant to prevention measures of pollution by heavy distillate. It showed that part of the biological surfactants is reaching a stage of its being industrially produced by gene recombination bacteria, but as a whole, biosynthetic genes have hardly been elucidated. In 2), a survey of high-grade treatment technology of petroleum coke was made. It pointed out that it is necessary to develop a technology which makes the most of features of petroleum coke and allows defects. In 3), scientists and engineers of Japan and Europe searched for themes on which they can jointly study in the fields of NOx removal catalyst, up-grading of fuel, and development of catalyst combustion of fuel. 287 refs., 136 figs., 128 tabs.

  5. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use unused hydrocarbon resource, technology of solid electrolyte fuel cells for high-efficient electric vehicles); 1993 nendo kokusai kenkyu kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kokoritsu denki jidosha no kotai denkaishitsu nenryo denchi gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) solid electrolyte fuel cell (SOFC) technology for high-efficient electric vehicles. In 1), bio-remediation is a choice as the result of trially using technologies for remediation of the environment polluted by pollutant, but it is not a technically completed one, but one which will be improved by trial and error. By the application of gene engineering, the use of gene recombination enables wide spread of decomposition genes. In 2), technical subjects were studied such as superheavy distillate, oil shale, coalhead methane and methane hydrate. In 3), designed were cylinder type and planar type SOFC of 850degC operation and 10kW output. Accumulation and weight of a total SOFC system are 81 liters and 100 kg in cylinder type and 136 liters and 200 kg in planar type. The vehicle can be equipped with the SOFC. 171 refs., 72 figs., 54 tabs.

  6. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

  7. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  8. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  9. FY 1999 report on the results of the R and D project on the industrial technology for the global environment. R and D of the prediction technology of environmental effects brought by CO2 ocean sequestration (Development of prediction technology of environmental effects around the point of CO2 discharge and the research support survey); 1999 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo NEDO seika hokokusho. Nisankatanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of studying viability of CO2 ocean sequestration by discharging it at the intermediate depth of ocean, the R and D were conducted of 'prediction technology of environmental effects around the point of CO2 discharge,' and the FY 1999 results were summarized. In the study of elucidation of behavior of liquid CO2 at the time of discharge, melting speed of CO2 in water and seawater, 2D CO2 concentration distribution, etc. were measured using the circulation type deep-sea simulation experimental equipment. In the study of technology to send CO2 into the sea and dilute it, the process test using mock liquid was conducted. In the indoor experiment on CO2 effects on marine organisms, conducted were the detailed experiment on long-term effects of low concentration CO2 on sea urchins and shellfish, experiment on CO2 acute effects on eggs/fry and experiment on CO2 effects on adult fish. In the developmental study of the model to predict environmental effects around the point of CO2 discharge, carried out were the improvement of the model for prediction of effects on marine organisms, study of the CO2 diffusion in topographic features supposed to be Hawaii, etc. In the international joint study, measurement/observation technology, facilities, etc. were studied in preparation for the experiment actually conducted in the sea. (NEDO)

  10. Report on achievements in fiscal 1998. Research and development of a technology to forecast environmental effect in association with isolation of carbon dioxide in oceans. (Surveys on development and research support on a technology to forecast environmental effect in areas in the vicinity of CO2 discharging points); 1998 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. CO{sub 2} horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Atmospheric concentration of CO2 is increasing, and discussions are urged on measures to suppress emission of CO2 into atmosphere. While different CO2 fixing technologies may be conceived, there is a technology to utilize CO2 absorbing capability of ocean by discharging and dissolving CO2 artificially into middle layer of the ocean to separate CO2 from atmosphere. This technology is one of the technologies which are promising in the aspects of technology, economic performance, and possible amount of CO2 reduction. However, it is difficult to say that scientific and technological discussions have been given sufficiently on behavior of CO2 discharged into the ocean, effect of the discharge on environments, and CO2 separation capability of the ocean. Therefore, in the present research and development, a 'technology to forecast environmental effect in areas in the vicinity of CO2 discharging points' is developed to serve for acquiring technological prospect on the feasibility to realize the CO2 ocean separation by discharging CO2 into the middle layer of the ocean. The present fiscal year has performed researches on the following research and development items: elucidation of behavior of liquefied CO2 when discharged into the ocean, CO2 feeding and diluting technologies, indoor experiments on the effects of CO2 on ocean living organisms, and development of a model to forecast environments in areas in the vicinity of CO2 discharging points. (NEDO)

  11. FY 2000 report on the results of the project on the R and D of the global environmental industry technology. R and D of the technology for predicting environmental effects associated with the CO2 ocean sequestration (Development of the technology for predicting environmental effects in the area around the CO2 discharge point and survey for supporting study); 2000 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu (CO2 horyuten shuhen'iki no kankyo eikyo yosoku gijutsu no kaihatsu narabini kenkyu shien chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    To obtain the technical outlook for CO2 ocean sequestration by CO2 discharge into the intermediate layer, the R and D was conducted of the technology for predicting environmental effects in the area around the CO2 discharge point, and the FY 2000 results were summed up. In the elucidation study of the behavior at the time of discharging liquid CO2, the melting process of CO2 droplets discharged/dispersed into the seawater of the intermediate layer was observed, and the specific phenomenon of hydrate formation in the process of CO2 droplet formation was grasped. As to the technology for sending CO2 into the ocean and diluting it, experimental study was made of CO2 transportation technology from on the sea to the intermediate layer, technology for rapid dilution immediately after discharge, etc. About the indoor experiment on the CO2 influence on marine organisms, experiment on the CO2 influence was carried out using shells, sea urchin, red sea bream, etc. In the developmental study of models for predicting environmental effects in the area around the CO2 discharge point, the 3D two-phase flow LES model was developed as a model for predicting the CO2 behavior, and the simulation of the liquid CO2 discharge was made at the planned experimental site. The model for evaluation of the biological influence was also made which can consider the interaction between two kinds of organisms. (NEDO)

  12. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  13. Fiscal 1996 project on the modeling for effective energy consumption in developing countries under a consignment from NEDO. Recent on the results of the demonstrative study on scrap preheater of electric furnace in the iron making process (for public); 1996 nendo hatten tojokoku energy shohi koritsuka model jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Seitetsu katei ni okeru denkiro no genryo yonetsu sochi ni kakawaru jissho kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Indonesia is the biggest iron steel producing country in the ASEAN countries. Most of the production is produced by the electric furnace method in which iron steel scrap is used as a material. However, an energy saving measure in this method, the electric furnace scrap preheater using flue gas, has not yet been spread on a full scale. This R and D is aimed at developing jointly with Indonesia an electric furnace scrap preheater for medium/small size electric furnaces which are adoptable to the present iron making situation in Indonesia and installing it to the electric furnace of the iron making plant in Indonesia for a demonstrative study on energy saving, etc. Spread/expansion of the electric furnace scrap preheater which is an excellent energy saving system targeted expansion of energy saving technology not only of Indonesia, but of ASEAN countries and Japan. In this fiscal year, remodeling of part of the system was made by change of flue gas flow for increasing the energy saving effect, and at the same time, a research study was made of a scrap reheater effective as a total system. Moreover, the paper investigated technical data/information in Japan and overseas. 3 figs., 9 tabs.

  14. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

  15. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  16. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  17. Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

  18. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  19. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  20. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

  1. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  2. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

  3. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  4. Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

  5. Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

  6. Fiscal 1999 research report. Basic research for promotion of joint implementation programs (Comprehensive feasibility study on efficiency improvement of heat generation facility and heat network for district heating at middle and small cities in Moscow region, the Russian Federation - 2 model cities within the region); 1999 nendo Russia renpo Moscow shunai chusho toshi ni okeru chiiki danboyo netsu kyokyu shisetsu yusomo no koritsu kaizen keikaku sogo chosa hokokusho. Shunai 2 toshi wo model to suru

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The above-named effort aims to work out modification plans and to predict their energy saving, energy substituting, and greenhouse gas reduction effects, and thereby to scout out a project which will effectively utilize flexibility-ensuring 'joint implementation' for the attainment of greenhouse gas reduction levels defined at COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). The results of assessment of this project based on the outcome of the survey show that (1) there is necessity for the project and that the presence of needs to be urgently satisfied is clear, that (2) energy saving, energy substituting, and greenhouse gas reduction effects are proved to exist and that the project is therefore an appropriate candidate for an activity to be implemented jointly, that (3) Russian agencies concerned are strongly interested in the project and that a sufficiently cooperative system will be available toward implementation, and that (4) there is an extremely large room for energy saving in the district heating oriented heat supply business in Russia and that probabilities are quite high that natural gas-fired turbine cogeneration plants capable of improving overall energy efficiency will enjoy extensive diffusion. (NEDO)

  7. Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

  8. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the synthesis and processing of advanced biomaterials (fixation and effective utilization of carbon dioxide using peptides); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (peptide oyo nisanka tanso koteika yuko riyo gijutsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In fiscal 1997, study was made on formation of peptides with a biogenic function and molecular recognition function, and peptide materials. The existing automatic design technique of peptides including non-natural amino acids was applied to design of complementary peptides of proteins with known structures to optimize a development technique of ligand. Practical function of peptides as advanced receptor ligand was verified by applying the existing conformation control technique to stable holding of peptide active conformation. Creation of bio-materials, and development of preparation technology of bio-substrates and materializing technology of functional molecular materials were carried out. To construct an electron transfer system by self- organized body of peptides formed on a substrate, a peptide molecular device was prepared and verified using linkers. To use peptides as photoelectron functional molecule, metallized peptide with main helix structure was prepared. The possibility of molecular materials with a fixation function of CO2 was examined. A high-sensitivity bio-sensor was also mentioned. 75 refs., 130 figs., 25 tabs.

  9. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

  10. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology (R and D of the monitoring system using high-intensity X-ray pulse for power plants); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the result on R and D of the femtosecond technology in fiscal 1997. Ultrahigh-speed electronic technology is indispensable for industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. In R and D of metrological technology using ultra-short light-pulses, study was made on generating and controlling technology for ultra- short light/electron beam pulses. Ti-sapphire mode-locked laser was prepared, and it was found that time-fluctuation of mode-locked laser pulses is measurable up to 100 femtosecond level. As measures against an instability of gain-switching semiconductor laser, light injection from the outside was effective. The stable directivity of laser beam was obtained by regenerative amplifier, while less temperature variation of an optical switch was necessary to stabilize energy. To generate femtosecond high-intensity X-ray pulse by collision of laser and electron beams, it was confirmed that sub- picosecond synchronization is possible by RF and picosecond laser synchronization circuit. 48 refs., 89 figs., 11 tabs.

  11. FY 2001 report on the integrated evaluation of the research cooperation project. Research cooperation program on the development of environmental measurement use laser radar/research cooperation project on the mining waste water treatment technology using biology; 2001 nendo kenkyu kyoryoku jigyo sogo hyoka hokokusho. Kankyo kesokuyo reza reda no kaihatsu ni kansuru kenkyu kyoryoku - Baio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    By research groups having been sent, the integrated evaluation was made of the projects on the research cooperation with Indonesia in the development of environmental measurement use laser radar and the research cooperation with China in the mining waste water treatment technology using biology. As to the research cooperation with Indonesia, the purpose/target proposed were almost achieved, and all were favorably carried out. Especially, after finishing the project, the design/manufacture of an on-vehicle type Mie-scattering laser radar were made using the acquired laser technology. And, it was reported that an observation study of the state of air pollution in Bandung city was made using the laser radar. It can be said that generally the research cooperation with China was smoothly proceeded with. However, the Wushan mine is small in scale of management, and therefore, there might have been some points to be reviewed in selection of the mine for research. The pilot plant installed at the Wushan mine is not now operated. If the mine has strong management force, the effective use of the pilot plant after finishing the project might have been studied. (NEDO)

  12. Report of the FY 1995 research cooperation promotion projects (overall evaluation). Research cooperation in fuel cell utilization/district power generation system and village type technique for simplified continuous production of raw palm oil; 1995 nendo kenkyu kyoryoku suishin jigyo (sogo hyoka) hokokusho. Nenryo denchi katsuyo chiiki hatsuden system ni kansuru kenkyu kyoryoku / sonrakugata kan'i renzoku palm arayu seizo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research cooperation project for fuel cell utilization/district power generation system is conducted under the research cooperation agreement between NEDO and Electricity Generating Authority of Thailand (EGAT), to demonstrate a 50 kW pilot plant constructed at EGAT's Bang Pakong power station. The fuel cell reforms self-spouted natural gas into H{sub 2} as the fuel. It has produced a total power of 341,921 kWh under the conditions of cumulative operating time: 8,115.4 hours, longest continuous operating time: 1,100 hours, service factor: 89.64%, load ratio: 86.13% and system utilization factor: 77.20%. The fuel technique will be acceptable for Thailand, if it is economically competitive. The project for producing raw palm oil is for Malaysia. The facilities introduced and tested for the new process are a continuous steam-heated fruit remover, fiber/nut separator, and shell cutter. The new process is evaluated to produce higher-quality raw palm oil in higher yield while consuming less energy. The new process, whose steps are automated, saves operating cost, and suitable for Malaysia which is suffering shortage of manpower. (NEDO)

  13. Fiscal 1999 survey for promotion of geothermal energy development. Survey report of environmental impact survey - Hot spring fluctuation (No. B-5, Musadake district); 1999 nendo chinetsu kaihatsu sokushin chosa. Kankyo eikyo chosa hokokusho (onsen hendo) (No.B-5 Musadake chiiki)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    Research boreholes N11-MD-3 and -4 were drilled in Shibetsu-cho, Shibetsu-gun, Hokkaido, in the period July 1999 through December 1999, and thermal water was examined at the sites in July and November 1999. For the purpose of detecting the impact of the said work on the environment, local hot springs were examined for their status before, during, and after the drilling period. Measurements were conducted in the period August 5, 1998, through December 31, 2000. It was found that no fluctuation in water temperature or yield attributable to the drilling was detected. Hot springs were examined for nine items including water temperature and pH level at four spots which were Kaiyo-dai, River Tenyu, and Otoko-yu and Onna-yu of Kawakita Hot Spring, when 23-31 measurements were performed from each of the four. (NEDO)

  14. A model to facilitate collaborative social support for pregnant students in secondary schools

    Directory of Open Access Journals (Sweden)

    Matlala SF

    2017-09-01

    Full Text Available Sogo F Matlala Department of Public Health, University of Limpopo, Sovenga, South Africa Abstract: Pregnancy among secondary school students remains a public health problem and is associated with school dropout as well as poor maternal and child health outcomes. Schools in South Africa no longer expel pregnant students as was the case before 2000. Instead, the government encourages them to remain in class to complete their education, but pregnant students often face stigma, and some drop out of school as a result. To remain in class and access antenatal care, pregnant students require social support from teachers, parents and professional nurses. Unfortunately, teachers, parents and professional nurses support pregnant students on an ad hoc basis, and this calls for a model to facilitate collaborative social support. The purpose of this paper is to present and describe a model to facilitate collaborative social support for pregnant students attending secondary schools in South Africa, using the model description steps of Chinn and Kramer. The model is designed as a tool to enable pregnant students to remain in school, attend antenatal care and in the end, deliver healthy babies. The professional nurse, as a member and leader of the school health team which visits secondary schools to provide a package of school health services, is the agent or facilitator of the model. Keywords: communication, health team, learner pregnancy, maternal and child health, school health services, social network

  15. Generation and characterization of neurogenin1-GFP transgenic medaka with potential for rapid developmental neurotoxicity screening

    International Nuclear Information System (INIS)

    Fan Chunyang; Simmons, Steven O.; Law, Sheran H.W.; Jensen, Karl; Cowden, John; Hinton, David; Padilla, Stephanie; Ramabhadran, Ram

    2011-01-01

    Fish models such as zebrafish and medaka are increasingly used as alternatives to rodents in developmental and toxicological studies. These developmental and toxicological studies can be facilitated by the use of transgenic reporters that permit the real-time, noninvasive observation of the fish. Here we report the construction and characterization of transgenic medaka lines expressing green fluorescent protein (GFP) under the control of the zebrafish neurogenin 1 (ngn1) gene promoter. Neurogenin (ngn1) is a helix-loop-helix transcription factor expressed in proliferating neuronal progenitor cells early in neuronal differentiation and plays a crucial role in directing neurogenesis. GFP expression was detected from 24 h post-fertilization until hatching, in a spatial pattern consistent with the previously reported zebrafish ngn1 expression. Temporal expression of the transgene parallels the expression profile of the endogenous medaka ngn1 transcript. Further, we demonstrate that embryos from the transgenic line permit the non-destructive, real-time screening of ngn1 promoter-directed GFP expression in a 96-well format, enabling higher throughput studies of developmental neurotoxicants. This strain has been deposited with and maintained by the National BioResource Project and is available on request ( (http://www.shigen.nig.ac.jp/medaka/strainDetailAction.do?quickSearch=true and strainId=5660)).

  16. Profiling of Escherichia coli Chromosome database.

    Science.gov (United States)

    Yamazaki, Yukiko; Niki, Hironori; Kato, Jun-ichi

    2008-01-01

    The Profiling of Escherichia coli Chromosome (PEC) database (http://www.shigen.nig.ac.jp/ecoli/pec/) is designed to allow E. coli researchers to efficiently access information from functional genomics studies. The database contains two principal types of data: gene essentiality and a large collection of E. coli genetic research resources. The essentiality data are based on data compilation from published single-gene essentiality studies and on cell growth studies of large-deletion mutants. Using the circular and linear viewers for both whole genomes and the minimal genome, users can not only gain an overview of the genome structure but also retrieve information on contigs, gene products, mutants, deletions, and so forth. In particular, genome-wide exhaustive mutants are an essential resource for studying E. coli gene functions. Although the genomic database was constructed independently from the genetic resources database, users may seamlessly access both types of data. In addition to these data, the PEC database also provides a summary of homologous genes of other bacterial genomes and of protein structure information, with a comprehensive interface. The PEC is thus a convenient and useful platform for contemporary E. coli researchers.

  17. Transcription profile of Escherichia coli: genomic SELEX search for regulatory targets of transcription factors.

    Science.gov (United States)

    Ishihama, Akira; Shimada, Tomohiro; Yamazaki, Yukiko

    2016-03-18

    Bacterial genomes are transcribed by DNA-dependent RNA polymerase (RNAP), which achieves gene selectivity through interaction with sigma factors that recognize promoters, and transcription factors (TFs) that control the activity and specificity of RNAP holoenzyme. To understand the molecular mechanisms of transcriptional regulation, the identification of regulatory targets is needed for all these factors. We then performed genomic SELEX screenings of targets under the control of each sigma factor and each TF. Here we describe the assembly of 156 SELEX patterns of a total of 116 TFs performed in the presence and absence of effector ligands. The results reveal several novel concepts: (i) each TF regulates more targets than hitherto recognized; (ii) each promoter is regulated by more TFs than hitherto recognized; and (iii) the binding sites of some TFs are located within operons and even inside open reading frames. The binding sites of a set of global regulators, including cAMP receptor protein, LeuO and Lrp, overlap with those of the silencer H-NS, suggesting that certain global regulators play an anti-silencing role. To facilitate sharing of these accumulated SELEX datasets with the research community, we compiled a database, 'Transcription Profile of Escherichia coli' (www.shigen.nig.ac.jp/ecoli/tec/). © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

  18. A novel, simple, high-throughput method for isolation of genome-wide transposon insertion mutants of Escherichia coli K-12.

    Science.gov (United States)

    Miki, Takeyoshi; Yamamoto, Yoshihiro; Matsuda, Hideo

    2008-01-01

    We developed a novel, simple, high-throughput method for isolation of genome-wide transposon insertion mutants of Escherichia coli K-12. The basic idea of the method is to randomly disrupt the genes on the DNA fragments cloned on the Kohara library by inserting a mini-transposon first, and then transfer the disrupted genes from the lambda vector to the E. coli chromosome by homologous recombination. Using this method, we constructed a set of 8402 Km(r) cis-diploid mutants harboring a mini-Tn10 insertion mutation and the corresponding wild-type gene on a chromosome, as well as a set of 6954 haploid mutants derived from the cis-diploid mutants. The major advantage of the strategy used is that the indispensable genes or sites for growth can be identified. Preliminary results suggest that 415 open reading frames are indispensable for growth in E. coli cells. A total of 6404 haploid mutants were deposited to Genetic Strains Research Center, National Institute of Genetics, Japan (Chapter 26) and are available for public distribution upon request (http://shigen.lab.nig.ac.jp/ecoli/strain/nbrp/resource.jsp).

  19. Survey report for fiscal 1999 on internationalization of technologies for effective use of energy resources. Survey of international trend of technology management (Survey of necessity of creating a strategic research organization for researches on technology, management, innovation, etc., for international competitiveness enhancement); 1999 nendo energy shigen yuko riyo gijutsu kenkyu kokusaika chosa kokusai gijutsu keiei doko chosa hokokusho. Kokusai kyoryoku kyoka wo mokuteki to suru 'gijutsu' 'keiei' 'innovation' nado no senryakuteki kenkyu kiko sosetsu no hitsuyosei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Innovation plays an important role for Japan to flexibly utilize its achievements for the purpose of properly responding to new business environments and to secure competitiveness in the market. Japan lacks experts equipped with knowledge and ability as regards technology development and management which are necessary for the planning and creation of technologies, and is also short of institutes for raising experts. In America, technology management won an important position in the 1980s in the effort at industrial renovation, and the industry, government, and academia in a body endeavored to elevate the level steadily, continuously, and deliberately, to eventually provide a source of great propulsion and international competitiveness toward today's economic success. Investigations were conducted, and a proposition is made for the establishment of an international technology management research center. Such a center will study technology management and innovation through international exchange based mainly on the industrial circle and through the organic coordination of the industry, government, and academia for widely observing changes in international society for economic frontier cultivation. A practical training and intelligent network will be organized on the global scale, which will serve as an information transmitter. A skeleton of the plan is shown. (NEDO)

  20. Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

  1. Industrial and scientific technology research and development project fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Report on research and development of a brain type computer architecture `trial fabrication and high-level evaluation on chips for a large-scale artificial neural system` and on results of evaluation studies on the chips; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Nogata computer architecture no kenkyu kaihatsu `daikibo jinko shinkei kairo system yo chip no shisaku to kodo hyoka` chip hyoka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop a brain type computer architecture, a brain mimic processor (BMP) has been developed (which was made in LSI in fiscal 1997), and studies are being made on developing its applications. Development has been made on an element in which linkage of one million cells with one thousand neural cells can be realized. Evaluation substrates mounted with the BMP, control software, and compilers were provided to 15 organizations including the National Research Institutes, universities, corporations, and other societies (for 19 themes) to evaluate capability of the LSI and its application development. All of the research organizations are using these items utilizing features of the LSI or the network for such purposes as learning, storage, recognition and control. The applicable theme may include infrared spectrum pattern recognition and domain division of document images using neural network functions. It can also include structural analysis of mass spectrum molecules, time series pattern recognition, location of corresponding points in images, estimation of moving images, satellite control, character recognition, short time storage, long-term association memory models, and invention process studies, all utilizing the functions of the BMP. 71 refs., 89 figs., 9 tabs.

  2. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

  3. The source and behavior of iodine dissolving in groundwater in the Mobara gas field, Japan

    Energy Technology Data Exchange (ETDEWEB)

    Kamei, Gento [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan). Tokai Works

    2002-06-01

    The groundwater of the Mobara gas-field in Boso peninsula, eastern Japan, contains considerable amount, around 100 mg/L, of iodine besides dissolved methane. Twelve groundwater samples from gas-producing wells to the aquifer within the Kazusa Group in Mobara and Naruto districts have been analyzed for iodine, pH, Eh, HCO{sub 3}{sup -}, NH{sub 4}{sup +}, SiO{sub 2}(aq), {delta}D, {delta}{sup 18}O, {delta}{sup 13}C{sub CH4} and seventeen elements. There is a good correlation between the concentrations of the dissolved elements to those in marine algae. The principal source of the iodine is believed to be algae buried in the sediments and the iodine has been discharged to the porefluid during decomposition of the tissue. The molar ratio of I{sup -}/Cl{sup -} in the groundwater increases from 1.0 x 10{sup 3} to 2.2 x 10{sup 3} with changing the depth from 2000 to 1000 meters below the surface and turns to decrease from 2.2 x 10{sup 3} to 1.8 x 10{sup 3} with going up from 1000 to 500 meters. This tendency may be caused by the variation of buried organisms due to changing the sedimentary environment. The observed variation in the ratio indicates that the iodine discharged in the pore fluid did not migrate significantly after the deposition of the formation. This paper can be regarded as an English version of Japanese article written by Kamei, which was published on the 'Shigen Chishitsu (Resource Geology)' 51(2)145-151(2000). (author)

  4. OryzaGenome: Genome Diversity Database of Wild Oryza Species

    KAUST Repository

    Ohyanagi, Hajime

    2015-11-18

    The species in the genus Oryza, encompassing nine genome types and 23 species, are a rich genetic resource and may have applications in deeper genomic analyses aiming to understand the evolution of plant genomes. With the advancement of next-generation sequencing (NGS) technology, a flood of Oryza species reference genomes and genomic variation information has become available in recent years. This genomic information, combined with the comprehensive phenotypic information that we are accumulating in our Oryzabase, can serve as an excellent genotype-phenotype association resource for analyzing rice functional and structural evolution, and the associated diversity of the Oryza genus. Here we integrate our previous and future phenotypic/habitat information and newly determined genotype information into a united repository, named OryzaGenome, providing the variant information with hyperlinks to Oryzabase. The current version of OryzaGenome includes genotype information of 446 O. rufipogon accessions derived by imputation and of 17 accessions derived by imputation-free deep sequencing. Two variant viewers are implemented: SNP Viewer as a conventional genome browser interface and Variant Table as a textbased browser for precise inspection of each variant one by one. Portable VCF (variant call format) file or tabdelimited file download is also available. Following these SNP (single nucleotide polymorphism) data, reference pseudomolecules/ scaffolds/contigs and genome-wide variation information for almost all of the closely and distantly related wild Oryza species from the NIG Wild Rice Collection will be available in future releases. All of the resources can be accessed through http://viewer.shigen.info/oryzagenome/.

  5. Seismic imaging for an ocean drilling site survey and its verification in the Izu rear arc

    Science.gov (United States)

    Yamashita, Mikiya; Takahashi, Narumi; Tamura, Yoshihiko; Miura, Seiichi; Kodaira, Shuichi

    2018-01-01

    To evaluate the crustal structure of a site proposed for International Ocean Discovery Program drilling, the Japan Agency for Marine-Earth Science and Technology carried out seismic surveys in the Izu rear arc between 2006 and 2008, using research vessels Kaiyo and Kairei. High-resolution dense grid surveys, consisting of three kinds of reflection surveys, generated clear seismic profiles, together with a seismic velocity image obtained from a seismic refraction survey. In this paper, we compare the seismic profiles with the geological column obtained from the drilling. Five volcaniclastic sedimentary units were identified in seismic reflection profiles above the 5 km/s and 6 km/s contours of P-wave velocity obtained from the velocity image from the seismic refraction survey. However, some of the unit boundaries interpreted from the seismic images were not recognised in the drilling core, highlighting the difficulties of geological target identification in volcanic regions from seismic images alone. The geological core derived from drilling consisted of seven lithological units (labelled I to VII). Units I to V were aged at 0-9 Ma, and units VI and VII, from 1320-1806.5 m below seafloor (mbsf) had ages from 9 to ~15 Ma. The strong heterogeneity of volcanic sediments beneath the drilling site U1437 was also identified from coherence, calculated using cross-spectral analysis between grid survey lines. Our results suggest that use of a dense grid configuration is important in site surveys for ocean drilling in volcanic rear-arc situations, in order to recognise heterogeneous crustal structure, such as sediments from different origins.

  6. A century of oceanographic and fisheries exploration on the continental shelf off Argentina

    Science.gov (United States)

    Angelescu, V.; Sánchez, R. P.

    1995-03-01

    the pooling of human resources set the basis for the development of bilateral programmes. Similar progress in Brazil and Uruguay led to the outgrowth of regional activities. Joint scientific efforts described in this analysis include the programmes carried out by the research vessels of Germany (“Walther Herwig”, “Meteor”), Japan (“Kaiyo Maru”, “Orient Maru”, “Shinkai Maru”), Poland (“Professor Siedlecki”), Russia (“Evrika”, “Dimitry Stefanov”) and the USA (“Vema”, “Atlantis II”), the achievements of which are a landmark in the evolution of marine science in the aea.

  7. The scale of hydrothermal circulation of the Iheya-North field inferred from intensive heat flow measurements and ocean drilling

    Science.gov (United States)

    Masaki, Y.; Kinoshita, M.; Yamamoto, H.; Nakajima, R.; Kumagai, H.; Takai, K.

    2014-12-01

    Iheya-North hydrothermal field situated in the middle Okinawa trough backarc basin is one of the largest ongoing Kuroko deposits in the world. Active chimneys as well as diffuse ventings (maximum fluid temperature 311 °C) have been located and studied in detail through various geological and geophysical surveys. To clarify the spatial scale of the hydrothermal circulation system, intensive heat flow measurements were carried out and ~100 heat flow data in and around the field from 2002 to 2014. In 2010, Integrated Ocean Drilling Program (IODP) Expedition 331 was carried out, and subbottom temperature data were obtained around the hydrothermal sites. During the JAMSTEC R/V Kaiyo cruise, KY14-01 in 2014, Iheya-North "Natsu" and "Aki" hydrothermal fields were newly found. The Iheya-Noth "Natsu" and "Aki" sites are located 1.2 km and 2.6 km south from the Iheya-North original site, respectively, and the maximum venting fluid temperature was 317 °C. We obtained one heat flow data at the "Aki" site. The value was 17 W/m2. Currently, the relationship between these hydrothermal sites are not well known. Three distinct zones are identified by heat flow values within 3 km from the active hydrothermal field. They are high-heat flow zone (>1 W/m2; HHZ), moderate-heat-flow zone (1-0.1 W/m2; MHZ); and low-heat-flow zone (<0.1 W/m2; LHZ). With increasing distance east of the HHZ, heat flow gradually decreases towards MHZ and LHZ. In the LHZ, temperature at 37m below the seafloor (mbsf) was 6 °C, that is consistent with the surface low heat flow suggesting the recharge of seawater. However, between 70 and 90 mbsf, the coarser sediments were cored, and temperature increased from 25 °C to 40°C. The temperature was 905°C at 151 mbsf, which was measured with thermoseal strips. The low thermal gradient in the upper 40 m suggests downward fluid flow. We infer that a hydrothermal circulation in the scale of ~1.5 km horizontal vs. ~a few hundred meters vertical.

  8. EDITORIAL: Focus on Cold and Ultracold Molecules FOCUS ON COLD AND ULTRACOLD MOLECULES

    Science.gov (United States)

    Carr, Lincoln D.; Ye, Jun

    2009-05-01

    öhlich, A Griesmaier, T Pfau, H Saito, Y Kawaguchi and M Ueda High-energy-resolution molecular beams for cold collision studies L P Parazzoli, N Fitch, D S Lobser and H J Lewandowski Collisional effects in the formation of cold guided beams of polar molecules M Motsch, C Sommer, M Zeppenfeld, L D van Buuren, P W H Pinkse and G Rempe Towards sympathetic cooling of large molecules: cold collisions between benzene and rare gas atoms P Barletta, J Tennyson and P F Barker Efficient formation of ground-state ultracold molecules via STIRAP from the continuum at a Feshbach resonance Elena Kuznetsova, Marko Gacesa, Philippe Pellegrini, Susanne F Yelin and Robin Côté Emergent timescales in entangled quantum dynamics of ultracold molecules in optical lattices M L Wall and L D Carr Rotational state resolved photodissociation spectroscopy of translationally and vibrationally cold MgH+ ions: toward rotational cooling of molecular ions K Højbjerre, A K Hansen, P S Skyt, P F Staanum and M Drewsen Collective transverse cavity cooling of a dense molecular beam Thomas Salzburger and Helmut Ritsch A Stark decelerator on a chip Samuel A Meek, Horst Conrad and Gerard Meijer Deceleration of molecules by dipole force potential: a numerical simulation Susumu Kuma and Takamasa Momose Ultracold molecules: vehicles to scalable quantum information processing Kathy-Anne Brickman Soderberg, Nathan Gemelke and Cheng Chin Magnetic field modification of ultracold molecule-molecule collisions T V Tscherbul, Yu V Suleimanov, V Aquilanti and R V Krems Spectroscopy of 39K85Rb triplet excited states using ultracold a 3Σ+ state molecules formed by photoassociation J T Kim, D Wang, E E Eyler, P L Gould and W C Stwalley Pumping vortex into a Bose-Einstein condensate of heteronuclear molecules Z F Xu, R Q Wang and L You Intense atomic and molecular beams via neon buffer-gas cooling David Patterson, Julia Rasmussen and John M Doyle Dynamical properties of dipolar Fermi gases T Sogo, L He, T Miyakawa, S Yi, H Lu