WorldWideScience

Sample records for kaihatsu sekiyu seisei

  1. Achievement report for fiscal 2000 on development of technology to evaluate reliability of petroleum refining facilities; 2000 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in development of a technology to evaluate reliability of petroleum refining facilities. The development efforts were made mainly on analyses by simulation and neural net (NN) that utilize computers. In the high-temperature system facilities, the creep damage generation is governed by different factors including impurities. The evaluation on joint life requires simultaneous use of low temperature zone long-time test. Verification was made on application of non-destructive inspection, such as use of ultrasonic waves in the accelerated creep zone. Defect detecting capability was identified when an ultrasonic wave flaw detection model is used for buried piping. In the pulse eddy current flaw detection, a coil most superb in totality was selected by means of simulation, by which corrosion and wall thickness of piping and devices were detected from outside the sheathing materials. Development was made on a technology to diagnose and evaluate corrosion of tank in operation by using the AE method. The remaining life of transformers is determined by how seriously the coil insulating paper has been deteriorated, and furfural in the oil was found effective for the parameters. Particularly, application of the NN was revealed to be effective in estimating electric motor deterioration. A high-temperature sulfide corrosion rate estimating model was developed from the operation and measurement data of the facilities by applying the NN and TCBM. (NEDO)

  2. Achievement report for fiscal 2000 on development of technologies to reduce pollutants in oil refining; 2000 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    NONE

    2001-03-01

    Research and development has been made on technologies to reduce sulfur content in light oil and on optimization of light oil quality. This paper summarizes the achievements in fiscal 2000. In the study of enhancing the desulfurization rate in gas oil deep hydrodesulfurization process, it was found that NiHY zeolite having Ni introduced by using the ion exchange method shows stable activity, whereas the target of sulfur content of 50 ppm or lower was achieved by adding the third constituent and by optimizing the impregnation solution to pH3. In the study of the Ni, Mo/alumina catalyst, the desulfurization activity was enhanced by optimization of carrier pore size to 120 to 140 angstroms and by addition of phosphorus and silica, having the target of sulfur content of 50 ppm or lower achieved. In the research of manufacturing low-sulfur light oil using heavy oil desulfurization and hydrocracking, optimization was performed on the catalyst used in the latter stage of heavy oil desulfurization, and evaluation was given on the performance in combination of commercially available hydrometallation catalyst/middle part HDS catalyst/bottom part HDS catalyst. As a result, achievement of the target of sulfur content in the desulfurized light oil of 300 ppm or lower was verified. Life evaluation test is in continuation on the heavy oil hydrocracking catalyst. (NEDO)

  3. FY 1999 report on the results of the technology development for abatement of pollutants related to oil refining; 1999 nendo sekiyu seisei osen busshitsu teigen nado gijutsu kaihatsu seika hokokusho

    NONE

    2000-03-01

    The technologies are developed for efficiently, economically improving quality of automobile fuels by, e.g., abatement of environmental pollutants present in the oil products. For improvement of hydrodesulfurization rate of gas oil deep hydrodesulfurization process, the catalyst components high in isomerization ability of the hard-to-desulfurize compounds are investigated, and effectiveness of zeolite is confirmed. For production of low-sulfur gas oil by hydrodesulfurization and hydrocracking of heavy oil, the catalyst with small pores is preferable for desulfurization of gas oil as the co-product of the treatment of heavy oil in the presence of catalyst for heavy oil desulfurization. For hydrocracking, the catalysts are prepared, on a trial basis, for achieving the target gas oil sulfur content of 10ppm or less by optimizing the zeolite and matrix properties. For suitability of gas oil qualities, it is found that the hydrogenation step is the rate-determining step among the reaction routes involved in the hydrogenation of difficult-to-desulfurize compounds. The data of low-sulfur gas oil qualities in Europe are collected. (NEDO)

  4. FY 1999 report on the results of the R and D on the assessment of reliability of oil refining facilities; 1999 nendo sekiyu seisei setsubi shinraisei hyoka nado gijutsu kaihatsu seika hokokusho

    NONE

    2000-03-01

    At present, in oil refineries in Japan, the term of the continued operation in oil refining facilities is shorter than that in Europe and America because of the regulation on the open inspection period for boilers and hazardous material storage tanks. As a result, the refining cost is comparatively higher than in Europe and America due to the increase in inspection/repair cost and decrease in operational rate. Therefore, it is becoming important to effectively supply petroleum products by keeping stability in oil refining facilities of the whole Japan and prolonging the term of the continued operation of oil refining facilities, etc. In this R and D, the technical development is conducted which is needed for the long-term continued operation of oil refining facilities. The items for the R and D are as follows: assessment technology of reliability of oil refining high temperature system facilities, assessment technology of reliability of piping/storage facilities in oil refinery, assessment technology of reliability of oil refining power system facilities, technology of management support system in oil refining facilities. In this fiscal year, technical survey, data collection, and construction of the basic concept of developmental technology were mostly conducted. Also conducted were trial manufacture of various probes for non-fracture inspection use, oscillators, etc., and basic design of inspection equipment and trial manufacture of a part of them. And the data acquired were analyzed. (NEDO)

  5. Fiscal 1998 R and D on original advanced material creation technology (development of precise structure control materials for oil refinery improvement). R and D result report on multi-dimensional polymers; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho. Tajigen kukan polymer no kenkyu kaihatsu

    NONE

    1999-03-01

    For development of radical-controlled synthesis technology of aromatic compounds using enzyme-related catalysts and synthesis technology of ordered compounds, and development of synthesis technology of new polymer groups with non-covalent bond linkages and new topological structures, this R and D on multi-dimensional polymers is promoting 2 research themes, (1) precise polymer synthesis technology using enzyme-related catalysts, and (2) chemical synthesis technology for polymers with non-covalent bond linkages and new topological structures. The joint research on (1) precise polymer synthesis technology using enzyme-related catalysts established the high-yield synthesis technology of phenol dimer first in the world. The joint research first studied the synthesis using 2,6-dimethylphenol as monomer through synthesis of phenol groups using ferrosalen, and obtained the mixture of polymer components more than 10,000 in molecular weight and low-molecular weight components by using 1,4- dioxane as solvent. (NEDO)

  6. Research and development of a technology to create original high-function materials in fiscal 1998 (development of precision structure controlling materials by improving petroleum refining). Report on achievements in research and development of precision catalytic polymerization; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu (seimitsu shokubai jugo no kenkyu kaihatsu)

    NONE

    1999-03-01

    Research and development on precision catalytic polymerization aims at developing polymerizing catalysts that can control arbitrarily the molecular weight and three-dimensional regularity by which rapid enhancement can be expected in performance of additional polymerization type polymers, and the primary structure of terminal groups. Works are being done on two sub-themes of ultimate additional polymerization and orientation catalyst polymerization. The research and development of the ultimate additional polymerization included structural control in polymerization reaction in vinyl chloride, vinylester and acrylic monomers, radical polymerization with precision orientation control, anionic polymerization with precision structural control, and precision polymerization utilizing asymmetric metal porphyrin complexes. In the research and development of the orientation catalyst polymerization, the orientation catalyst polymerization was researched and developed, elementary reaction of metallocene was elucidated, high-performance carrier catalysts were developed, advanced function polymers were synthesized at high precision based on metathesis, and improvement of functions of polyolefin was researched and developed. Surveys and studies were carried out on fundamental technologies common to the above two themes re-commissioned to five universities. (NEDO)

  7. Industry brief letter; Kasupikaioki sekiyu koku kaihatsu sekiyu shigen kaihatsu nado sannyu

    NONE

    1999-02-01

    4 companies of Petroleum Resources Development, Indonesia Petroleum, Teikoku Petroleum an Itochu Petroleum Development will sign petroleum exploration and development contract in petroleum mining property offshore of Caspian Sea with Azerbaijan National Petroleum Company, Sokar Company. In another mining property, Mitsui group reached conclusion with Sokar Company in mining right. Resource development competition between existing international petroleum majors and Japanese petroleum companies around Caspian Sea may be further intensified. (translated by NEDO)

  8. Achievement report for fiscal 2000 on research and development of human cooperating and coexisting robot system. Research and development of rationalization in oil refining system; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Sekiyu seisei system gorika kenkyu kaihatsu

    NONE

    2001-06-01

    It is intended to develop a human cooperating and coexisting robot system that can move around freely during operation and shutdown of a oil refining plant to perform different works. This paper describes the achievements in fiscal 2000. With regard to the navigation and maintenance work functions, design was made on the robot induction system and its conception to perform the works after the robot has reached a place of the work. The specifications required for the robot supporting agent were made clear, and the constituting modules were designed to exchange information with the robot. Specifications were compiled for a portable remote operation device intended of operating different vehicles. Investigations were carried out on such protection technologies as interference check and shock absorbing materials to protect the robot platform. A method was developed to acquire posture and motion patterns of a human demonstrator, using only the upper half of the body, from the images captured by a head-mounted camera. Discussions were given on the specifications, systems and image processing algorithms required for vision-navigated autonomous walking, whose practicability was verified. Autonomous walking by means of map-based guidance, and hand operating technologies were also discussed. (NEDO)

  9. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  10. Concerning problems of petroleum refining facilities. ; Promote international lateral work sharing, and strengthening of infrastructures in petroleum industry. Sekiyu seisei setsubi mondai ni tsuite. ; Kokusei suihei bungyo no suishin to sekiyu sangyo no kiban kyoka wo

    1991-06-05

    This paper discusses how to promote international lateral work sharing and how to strengthen infrastructures in the petroleum industry, as a problem prevailing over the petroleum refining facilities in Japan. Excess distillation facilities have been applied with the disposition policy. However, in view of the supply and demand situation in petroleum products for medium to long term span in the world with the pan-Pacific region as the main concern, that applicable to Japan, and that experienced during the Persian Gulf crisis, the excess facility disposition policy was revised, particularly on white kerosene, of which supply and demand tightness is concerned about, so that production capacities may be increased as required. Japan, a large presence in the international economics, is required to work more positively on petroleum refining facilities located in the oil producing countries and intermediate locations to promote the international lateral work sharing. On the one hand, in order to strengthen the infrastructures in the Japanese petroleum industry, it is necessary to promote rationalization and use at higher efficiency of the oil supply system, and convergence of the the petroleum industry, including joint investments for projects exceeding capabilities of individual enterprises. 3 tabs.

  11. Present developmental conditions petroleum substituting energies in the EU; Sekiyu daitai energy kaihatsu no genjo (EU)

    NONE

    1997-03-01

    This report outlines the policy of development and introduction of petroleum substituting energies, and its diffusion situation in the EU. On the policy, development, introduction and diffusion of petroleum substituting energies in the EU, based on the new EU energy white paper issued in fiscal 1996, the policy of energy and environment in every EU country is first outlined. The policy of and practical approach to petroleum substituting energies in every EU country are next described. In particular, since ALTENER which has been continuously promoted by the EU for 3 years as main control measures against CO2 is newly moving toward the second plan, the trend of ALTENER and the new SAVE2 plan are presented. The content of JOULE-THERMIE is also precisely presented which is the new energy program of the 4th framework R & D program. In relation to the developmental trend of alternative energies to oil in the EU until 2020, its prediction result is presented on the basis of the latest study promoted by EC committee in the ALTENER plan. 10 tabs.

  12. Present developmental conditions of petroleum substituting energies in France; Sekiyu daitai energy kaihatsu no genjo (France)

    NONE

    1997-03-01

    The French Government most enthusiastically promotes development of bio-gasoline in renewable energy field. EU makes pressure to remove the French Government`s fiscal advantages for bio-gasoline which only benefit French farmers, and the IEA (International Energy Agency) report also estimates no benefit corresponding to the fiscal support cost. Start of the `Eolien 2005` project is attractive in renewable energy field which aims at construction of wind power generation stations of 250-500MW by 2005. The `Eolien 2005` project is mainly supported by Electricite de France (EDF) who guarantees the purchase of produced electric power at a submitted price. In addition to this subsidy activity, EDF decided to positively tackle renewable energy. On R and D efforts for renewable energy, France belongs to the most poor countries among IEA countries, and in addition, the effort is considerably concentrated onto the study on reduction of production cost for bio-gasoline. There were no changes in this situation in 1996. 7 refs., 5 figs., 31 tabs.

  13. Current srate and problems in Japanese petroleum development. ; International trends in petroleum development and problems in Japanese devepment business. Waga kuni sekiyu kaihatsu no genjyo to mondai ten. ; Sekiyu kaihatsu no kokusai doko to waga kuni kaihatsu jigyo no kasai

    1991-11-05

    Petroleum production and its supply and demand require ever closer coordinations among the countries involved. On the other hand, however, there a large number of difficult questions as the problems of global environmental pollution and greenhouse effects increase their seriousness and the economic resources in the petroleum business become scarcer. This paper describes the current state of the Japanese petroleum development, the necessity of spontaneous petroleum development, the international trends in the petroleum development business, and the tasks for Japan in the petroleum development business. Japan is a late comer in the petroleum development business. There are such difficulties as sizes of oil fields being discoverd are becoming smaller, the natural conditions in development target areas are getting severer, and the economic effects are inferior. Japan, whose petroleum self-supply rate is about 0.3%, whose petroleum dependency is heightening as a result of increase in nuclear power generation, and who is the third largest petroleum consuming country next to the U.S.A and Soviet, must use efficiently her financial and technical powers to vitalize her spontaneous petroleum development. Japan has a duty to contribute to the world {prime}s future stabilized supply of oil. The Japanese Government has launched the five-year fund development plan to perform basic surveys for ail in the north-east part of the Japan Sea and the pacific Ocean.

  14. Present situation of the development of petroleum substitution energy (East Europe); Sekiyu daitai energy kaihatsu no genjo (Too)

    NONE

    1996-03-01

    In East European countries (Albania, Bulgaria, Czech, Slovakia, Hungary, Poland, Rumania and former Yugoslavia), energy prices were raised as part of the general price reform in the initial stage of the economic reform. Trade regulations on energy products were relaxed, and prices of tradable energy products were made free. Even in countries such as Rumania and Bulgaria where there still remain controls, the governments aim at perfect liberalization. Thus, this paper first considered the energy situation of East European countries where economy and society are now changing. Described were the overall economy situation and energy supply/demand in East European countries. Next, the paper detailed the energy situation in Hungary and Poland. In conclusion, the paper considered energy and international cooperation, and Pan-european Energy Charter which are important future issues in the energy sector of East European countries. 10 refs., 36 figs., 26 tabs.

  15. Present situation of the development of petroleum substitution energy (the U.S.); Sekiyu daitai energy kaihatsu no genjo (Beikoku)

    NONE

    1996-03-01

    The paper investigates and reports the trend of the development of petroleum substitution energy in the U.S. The Clean Coal Technology Plan is one of the plans which were implemented most successfully in the past several years. The plan made a remarkable reduction in NOx and SOx emissions possible. As for natural gas, importance is placed on improvement of production/storage technology of natural gas and high-effective low-NOx-emission turbines. As to the research on nuclear reactors, importance is now placed on the light water reactor plan, and the target is the design and development of such nuclear reactors as electric power companies pay attention to. The solar cell industry is markedly developing, and the shipment grows 17% per year. However, the price is rapidly declining. The wind turbine and biomass power generation plans are also advanced, and most of the plans are aimed at the development of new fields of application. With regard to geothermal energy, slowness is seen. Concerning electric vehicles, no makers enter into the quantity production, but the research and development are actively being made. 72 refs., 26 figs., 51 tabs.

  16. Present situation of the development of petroleum substitution energy (Germany); Sekiyu daitai energy kaihatsu no genjo (Doitsu)

    NONE

    1996-03-01

    The paper investigates and reports the developmental trend of petroleum substitution energy in Germany. Policies for the technical development and actual introduction of petroleum substitution energy in Germany are concerned with three energies: coal, natural gas, and new energy, except nuclear energy the use of which is against public opinion. Coal is the only abundant domestic resource, but not internationally competitive because of its cost. Brown coal obtained from the open pit mining is an abundant and low-cost domestic resource, but has the environmental problem. The latest technology is actually being introduced in which the thermal power generation is integrated into gasification, and the gas/steam turbine power generation. Natural gas is advancing in the use as energy source for space heating substituting for brown coal. The technology development of new energy is promoted mainly on such wind power and solar energy as are called renewable energy. As to the development of technology using renewable energy for which the rapid increasing use is not expected in near future, the target is directed mostly to CO2 control and the third world where there are no public electric power nets. 30 refs., 10 figs., 8 tabs.

  17. Present situation of the development of petroleum substitution energy (E.U.); Sekiyu daitai energy kaihatsu no genjo (EU)

    NONE

    1996-03-01

    The paper investigates and reports policies for and the developmental trend of petroleum substitution energy in the E.U. The technology of 18 wind turbine makers in West Europe is on a level that they can almost sell MW-class turbines for practical use. The wind turbine industry in Denmark is on a level of No.1 of the world, and occupies approximately 50% of the world market share. The capacity of the wind power generation in Germany which finished the installation at the end of 1995 exceeded 1000 MW. EEWC has recently been established as an organization for using waste as energy. Municipal solid wastes discharged in West Europe are regarded to be equivalent to 5% of all the power demand there. In Spain, biomass is a petroleum substitution energy source which is most used. A target amount for the use set by the government is equal to 427000 tons in oil. Biomass is most used in the residential field, and it is mainly the use of agricultural and forestry wastes as fuel. Rapeseed oil is studied as fuel for bio car. In Denmark, production of rapeseed as fuel use crop is increasing. 14 refs.

  18. Present situation of the development of petroleum substitution energy (The UK); Sekiyu daitai energy kaihatsu no genjo (Eikoku)

    NONE

    1996-03-01

    With relation to the petroleum substitution energy in the U.K., the paper states measures taken for the development and introduction and the state of spread. Introduced were the U.K., energy policy described by energy field, petroleum and natural gas, coal, nuclear power, electric power, renewable energy (petroleum substitution energy), and the policy on energy conservation and the recent trend. Further, the paper took up the environmental policy relating to global warming which is an environmental problem in close connection with the energy industry and described the present status of exhaust gas such as acid rain gas and ozonospherial destruction gas, target for reduction of exhaust gas, and the present situation of exhaust gas at power plant. Explained were the positioning of and the measures for the petroleum substitution energy which was incorporated into a part of the energy policy in the U.K., especially the recent trend of obligation to use non-fossil fuel. First, the order of priority of the governmental policies was introduced, and then the NFFO order was described which was to give reliable fund base to the development toward the practical use of petroleum substitution energy. The paper also commented on recent topics on the state of the practical use of petroleum substitution energy. 2 figs., 7 tabs.

  19. Mechanism of pyrrhotite formation from ferric oxyhydroxide catalyst; Kokoritsu sekitan ekika shokubai no kaihatsu (Okishi suisankatetsu shokubai karano pyrrhotite seisei kyodo)

    Tazawa, K.; Koyama, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    It is thought that iron-based catalysts for coal liquefaction exercise their catalytic activity by forming pyrrhotite (Fe(1-x)S). However, there are still a lot of unknown problems remained concerning the formation and agglomeration behaviors of pyrrhotite. These make a difficulty for improving the activity of iron-based catalysts. In this study, sulfiding behaviors of {alpha}-iron oxyhydroxide ({alpha}-FeOOH) and {gamma}-iron oxyhydroxide ({gamma}-FeOOH) were investigated to reveal the formation and agglomeration behaviors of pyrrhotite. It was found that pyrrhotite was easily converted from ferric oxyhydroxide catalysts having large specific surface areas at the sulfiding temperature below 250{degree}C, and fine crystallites of pyrrhotite were formed at the initial stage of sulfiding. Crystal growth of pyrrhotite at the sulfiding temperature over 350{degree}C depended on the catalyst forms. It was also found that smaller crystallites of pyrrhotite were formed from {gamma}-FeOOH than from {alpha}-FeOOH and amorphous iron oxyhydroxide. 5 refs., 7 figs., 1 tab.

  20. Evaluation report on the development of high-function ultrathin film for new oil refining process; Shinsekiyu seisei process ni kakawaru kinosei chousumaku no kaihatsu

    NONE

    2001-03-01

    This evaluation committee report covers the project entitled 'Development of high-function ultrathin film for new oil refining process' which was under way for three years from fiscal 1998 through 2000. The evaluation committee is so designed that researchers outside the organization responsible for the project performs an objective and impartial evaluation of the national project concerned as to its objective, goal, plan, operation, implementation system, rate of progress toward achievement, and the significance of the results achieved. The committee aims to disclose to the taxpayer the actualities of State-run research and development projects by making them transparent to people's eyes, which is one of the duties of the committee, and to elevate the value of the research results by impartially and duly evaluating them. In this report, the outlines of the project and of the obtained research results are introduced in Chapter 1, and then the details of the evaluation of the project are described in Chapter 2. It is stated that the organic/inorganic laminate membrane fabrication technology utilizing low temperature TiO{sub 2} film formation is evaluated high. It is also stated that the effect of the analysis and evaluation technology is expected to spread and find its use in various industrial fields. (NEDO)

  1. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  2. Fiscal 2000 survey report. Development of nucleation control technology for new functional alloy creation and development of new process; 2000 nendo kinosei shingokin sosei no tame no kaku seisei seigyo gijutsu kaihatsu oyobi shin process kaihatsu chosa hokokusho

    NONE

    2001-03-01

    For the above-said purposes, studies were conducted involving the construction of a database on supercooling and nucleation and on alloy species and functionality. Composition, concentration, supercooling method, container, atmosphere, maximum degree of supercooling, cooling rate, and the contents of the study to be made were investigated in the study of items for databasing. Also, in an experiment dealing with alloy species remaining to be exploited, the coagulation of drop size GaSb alloy was investigated. In the study of the formation of a quasi-stable phase in functional alloy, it was demonstrated that a nonequilibrium or quasi-stable phase might be quantitatively formed by use of a containerless process. In the study of texture control, texture fining by causing flowability was particularly investigated, and it was suggested that not only nucleation but also growth to follow should be properly controlled for the fining of coagulated texture. In the study of simulation of texture prediction, construction of a database on practical alloy nucleation frequency and stochastic simulation of coagulated texture to be built on this database were taken up. (NEDO)

  3. Report on current status of petroleum substituting energy development in the EU in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (EU))

    NONE

    1998-03-01

    The EU is one of the most advanced places of petroleum substituting energy development. The EU is highly aware of environmental issues. For the COP3 held at Kyoto in December 1997, The EU gave more severe regulation of CO2 emission than the other advanced countries. The EU takes efforts in the development and introduction of energy effective for global environmental protection. In addition, research and development of geothermal, biomass and wave force energy are actively promoted in this place. Energy situations in this place are significant for predicting and analyzing the future trends of energy development and consumption in the other countries. Firstly, this report looks back toward energy demand held in check to a head at the beginning of the 1990`s. Secondly, supply of energy and cover of energy trend are described for recent years from the point of view. Thirdly, competitiveness of energy in EU countries are discussed from a position of energy density. Fourthly, circumstances about environmental issues are considered. Fifthly, the world market of energy is also considered. Finally, development of new energy and a trend of introduction with a sample of Sweden are introduced. 13 refs., 15 figs., 28 tabs.

  4. Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    NONE

    1985-03-01

    In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

  5. Report on current status of petroleum substituting energy development in the USA in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (Beikoku))

    NONE

    1998-03-01

    In the last twenty-five years, the level of social recognition for the importance of energy conservation grew progressively from a total nonexistence of concern to the driving force that ensures the future environmental health of the nation and the world. Executive Order 12003, relating to energy policy and conservation, was signed by President Jimmy Carter and dated July 20, 1977. In 1992, President Clinton issued Executive Order 12759 - federal Energy Management. Each agency will prescribe policies under which its industrial facilities in the aggregate increase energy efficiency by at least 20% in fiscal 2000 in comparison to fiscal 1985. Current Federal programs for building efficiency are estimated to result in 31.5 billion dollars in annual energy saving for consumers by 2010. Future trends attract attention. The major programs currently in force to implement these policies and directives include Rebuild America, Million Solar Roofs Initiative, Home Energy Rating Systems, and Weatherization Assistance Program. 37 refs., 1 fig., 6 tabs.

  6. International cooperation project. Evaluation report on development of new oxidation and environment resistant materials for petroleum excavation; Sekiyu kussakuyo taisankasei taikankyosei shinzairyo no kaihatsu hyoka hokokusho

    NONE

    2001-03-01

    In order to enhance the environment and wear resisting performance of the bearing mechanism for petroleum excavation bits assuming use at a depth of 6,000 m, discussions were given on a cubic boron nitride based ultra-hard thin film and a Ti{sub x}M{sub 1-x}N based hard thin film as the new materials. This paper describes the evaluation report for the year 2000. It was found that the promising material is the Ti{sub x}M{sub 1-x}N. The practical applicability test would require a considerable amount of expense and insurance fee, while putting the material into practical use would take some more time. However, the achievements in developing this new material will allow the material to be applied to cutting tools used under the same onerous condition, and theoretical development would be possible on the consideration of the film properties, whereas further development may be expected in the future. An international joint study has performed evaluations on the environmental resistance and the characteristics of the film at the University of Toronto. These evaluations are effective in enhancing further the properties of the thin film in the future. Achievements have been accumulated steadily from starting the fundamental studies, and high level objectives have been achieved. Accurate identification has been made on the state of developing the parts for petroleum excavation bits, with the objectives set properly. Putting the bits into practical use will still require public assistance. (NEDO)

  7. Report on current status of petroleum substituting energy development in the UK in FY 1997; 1997 nendo chosa hokokusho (sekiyu daitai energy kaihatsu no genjo (Eikoku))

    NONE

    1998-03-01

    Blair`s cabinet of the UK, as soon as it was formed, started a review of all policies of the past Conservative government, including the area of energy and environment. The Labour Party has already underlined its commitment to promoting petroleum substituting, i.e., renewable energy. The government made clear that the unique British NFFO Scheme to promote sources of renewable energy would continue and in November, 1997 published the policy guide for the fifth round of NFFO bidding. The British energy market is generally considered to be the most liberalized for free competition in Europe and even the retail market for households is going to be completely open for competition in electricity and gas supply by 1998. As to the regulation of the green house gas exhaust, the Labour Party has put forward a target to cut 20% of the exhaust level of 1990 by the year 2010. The government is now preparing measures for its implementation. At present, the EU is debating the draft of the landfill directive. In the UK, the construction of waste incineration and power generating plants with modern technology is now being promoted. 27 tabs.

  8. Present developmental conditions of petroleum substituting energies in the U.S.A; Sekiyu daitai energy no kaihatsu no genjo (Beikoku)

    NONE

    1997-03-01

    The present developmental conditions of petroleum substituting energies in the U.S.A. were surveyed. The budget related to energy saving and petroleum substituting energies in the U.S.A. is on the increase. DOE`s expenditure on petroleum substituting energies increased from $6.8 billion in 1993 to $8.1 billion in 1995 (from 29.6% to 34.6% of DOE`s expenditure), showing the positive approach to development of petroleum substituting energies. Approaches to environmental protection are also in promotion such as positive use of electrical vehicles by U.S. government and emission regulation of specific pollutants by EPA. The state of California withdrew the regulation which prescribes that 2% of passenger cars sold in the state should be zero emission vehicles after 1998, because development of the battery with both sufficient mileage and output is impossible by 1998 in the present stage. The prospect of practical use of new batteries such as lithium battery is still far from certain for some years. Development of petroleum substituting energies in the U.S.A. is still insufficient. 17 refs., 1 fig., 4 tabs.

  9. Survey report on the development/utilization of petroleum substitution energy in the Pacific region; Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    NONE

    1998-03-01

    The paper collected/analyzed data on petroleum substitution energy in the Pacific region. In fiscal 1996, in addition to collection of the existing energy data, conducted were collection of energy data made retroactive from 1971, and time-series collection of the energy related expanded data including energy related production statistics/social statistics, energy consumption amount by industry, power generation facilities, oil production facilities, and environmental data. As to petroleum substitution energy, the paper took up new energy such as hydroelectric, nuclear, geothermal, photovoltaic, and wind power generation, and commercial-base renewable energy. As a result of the analysis, the supply of petroleum substitution energy in the whole Pacific region has been stable, 6.6% during 1980-1990, 7.4% in the first half of the 1990s, largely over the primary energy supply. The supply of nuclear power was overwhelmingly large, followed by hydroelectric energy and geothermal/new energy. 15 figs., 23 tabs.

  10. Achievement report for fiscal 1998. Research and development of synergy ceramics (Research and development of anti-corrosion technologies for oil production system); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    NONE

    1999-03-01

    A computer simulation-aided designing technology is completed to help develop synergy ceramics which are complicated in phase constitution and material structure. A program, which simulates sintering and particle growth for multiple solid-state and solid-state/liquid-phase systems, has been built assuming the form of an integrated micro/nano level simulation technology based on the Monte Carlo method. The new program applies to systems consisting of more than three different phases, and deals in a uniform way with the designing of various textures formable by transfer of matters in solid-state particle growth, Ostwalt ripening, solid-state sintering, liquid-phase sintering, and additive reaction. The Monte Carlo method-assisted program is applied to systems based on AlN, Si{sub 3}N{sub 4}, and Al{sub 2}O{sub 3}, and a good result is achieved in each case. The molecular dynamic method is mainly used in atom level simulation for application to ZrO{sub 2}-Y{sub 2}O{sub 3} and Si-C-N, and a good result is achieved in each case. (NEDO)

  11. National research and development project. Report on evaluation of research and development of remotely controlled excavators for highly deep submarine oil fields; Ogata kenkyu kaihatsu project. Daishindo enkaku sosa kaitei sekiyu kussaku sochi no kenkyu kaihatsu ni kakawaru hyoka hokokusho

    NONE

    1976-02-04

    Described herein are results of evaluation of the developed excavators remotely controlled for highly deep submarine oil fields. The excavator system was designed to work at the target water depth of 200 to 250 m and excavation depth of 8,000 to 9,000 m, though not quite satisfactorily. There were several practical problems to be solved, e.g., those found in accuracy of reentry in the excavated section, cables connecting the driving equipment to the excavated section, and entangled hoses. The works were divided and system was configured in an attempt to secure all-weather type serviceability and to improve economic viability. The other major works included attempts to improve equipment functions and reduce manpower cost. Nevertheless, however, the construction cost was considered to be higher than expected, and no firm prospect was obtained whether the new excavator system was economically competitive with the conventional rig. The factors that pushed up the construction cost were various facilities needed by the new system with the separated excavation and driving sections, e.g., those facilities for helping the system land on the sea bottoms, material supply/storage facilities, and automated/unmanned facilities. The system failure and other items related to reliability are no clearly understood, making it difficult to compare it with the conventional rig in service factor. It was not adequate, therefore, to advance the next R and D phase as planned, and decided that the project was suspended to see the world development trends, because the clear plans for the future could not be drawn at that time. (NEDO)

  12. FY1995 development of a clean CVD process by evaluation and control of gas phase nucleation phenomena; 1995 nendo kisokaku seisei gensho no hyoka to seigyo ni yoru clean CVD process no kaihatsu

    NONE

    1997-03-01

    The purpose of this study is to develop a high-rate and clean chemical vapor deposition (CVD) process as a breakthrough technique to overcome the problems that particles generated in the gas phase during CVD process for preparation of functional thin films cause reduced product yield and deterioration of the films. In the CVD process proposed here, reactant gas and generated particles are electrically charged to control the motion of them with an electric field. In this study, gas-phase nucleation phenomena are evaluated both theoretically and experimentally. A high-rate, ionized CVD method is first developed, in which reactant gas and generated particles are charged with negative ions generated from a radioisotope source and the UV/photoelectron method, and the motion of the charged gas and particles is controlled with an electric field. Charging and transport processes of fine particles are then investigated experimentally and theoretically to develop a clean CVD method in which generated particles are removed with the electric forces. As a result, quantitative evaluation of the charging and transport process was made possible. We also developed devices for measuring the size distribution and concentration of fine particles in low pressure gas such as those found in plasma CVD processes. In addition, numerical simulation and experiments in this study for a TEOS/O{sub 3} CVD process to prepare thin films could determine reaction rates which have not been known so far and give information on selecting good operation conditions for the process. (NEDO)

  13. FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    NONE

    1993-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  14. FY 1994 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1994 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    NONE

    1995-03-01

    This 5-year joint project (FY 1990 to 1994) by Japan and the Philippines is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized in the Philippines into electric power, in which thermal decomposition/gasification of the wastes is combined with a gas engine system. The field tests of the demonstration plant successfully produce power of 100 kW by burning only the low-calorie gas with a heating value near critical level for self-sustained combustion, obtained by gasification of sawdust by the fluidized gasifier and refined, attaining the object of the project. It is confirmed that a 200 to 300 kW class commercial plant can be designed and constructed basically by scaling up the 100 kW demonstration plant. The other data obtained by the field tests include those for improved operability and maintainability, gas purification, and reducing sizes of the facilities, including utility facilities. (NEDO)

  15. FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    NONE

    1991-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)

  16. FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    NONE

    1992-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  17. Technological development report for fiscal 1993 on the woodwaste thermolysis/gasification technology and generated gas utilization technology; 1993 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    NONE

    1994-03-01

    The project is a joint effort of Japan and the Philippines to develop a thermolysis/gasification system, in which woodwaste now remaining unexploited in the Philippines is subjected to thermolysis/gasification and the resulting gas is used in a gas engine for the generation of electric power, in a 5-year period beginning in fiscal 1990. In this fiscal year, element technology verification tests are conducted, components of a demonstration plant are manufactured, and procurement is made as required, which completes all the tasks allotted to this fiscal year. All the constituents of the said demonstration plant fabricated or procured since fiscal 1991 are packed up and forwarded to Industrial Technology Development Institute (ITDI) of the Philippines, and engineering guidance is extended and test operations are carried out at the site of plant installation. In line with the said endeavors, on-site investigations are performed and researches are conducted together with ITDI scientists concerning the construction work and element technology confirmation. On the other hand, the Philippine side performs the second phase of civil engineering and construction carried over from the first phase. The demonstration plant is completed, adjustment and test operations are carried out, which means that the project is in progress as initially scheduled. (NEDO)

  18. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  19. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  20. Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    NONE

    2001-03-01

    Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

  1. Industrial science and technology research and development institutions in fiscal 2000. Research and development of human media (Report on achievements in research and development of high-level information system for petroleum plant); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho (sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu)

    NONE

    2001-03-01

    Having selected a petroleum refining plant as a large and complex system, a system was developed, that is capable of operating safely and efficiently a plant even by young operators by utilizing the human media technology that realizes information environment having a sense of unity with humans. With this system, if an anomaly is detected in the plant condition, the agent and the operator talk with each other freely, and necessary items of information are displayed on a large screen from moment to moment according to the priority thereof. Activities were taken in the following nine areas: 1) the total system, 2) research on an interface agent, 3) research on hypothetic plant indication interface, 4) research on a discrete cooperative treatment technology, 5) research on plant models and interface systems, 6) research on plant ontology, 7) research on significance indication interface, 8) improvement of tools to structure a large-screen integrated indication system, and 9) investigations on technological trends in foreign countries. (NEDO)

  2. Fiscal 1997 report on the results of the R and D of industrial scientific technology. R and D of synergistic ceramics (R and D of corrosion prevention technology for the petroleum production system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

    NONE

    1998-03-01

    To heighten durability and safety of materials/parts for undersea oil drilling, the development of ceramic base materials was made by developing function harmony type process technology which harmonizes on a high grade contrary characteristics and various functions. The paper summed up the fiscal 1997 results. In the design of system formation, computational simulation technology was developed to the composite process and the diploid system. The development of multifunction simultaneous manifestation materials was trially made by the higher nano structure process. A study was made of control of microstructures of porous materials and matrix filling by the gas phase precipitation control. Proposed were selective control of grain growth from species crystals and the columnar particle orientation laminated structure of simultaneous manifestation of strength and toughness. By composite precipitation reaction control, studied were simultaneous dispersion of whisker and increase in density of matrixes, and harmonization with long fibers. Silicon nitride was trially made with low lubrication/friction coefficients and high strength. A simulation method for crack progress behavior evaluation was developed using a testing notched specimen heterogeneous microstructures. Analyses were made of brittle fracture mechanics and reliability evaluation. 273 refs., 344 figs., 29 tabs.

  3. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  4. FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

    NONE

    1999-09-01

    For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

  5. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  6. FY 1998 industrial technology R and D project. Report on the results of the development of utilization technology of biological resource such bioconsortia system (Development of production technology of biological use petroleum substituting fuels); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu)

    NONE

    1996-03-01

    Technology development was conducted for production of useful substances using the bioconsortia system. In FY 1998, the development of element technology was studied. As to the utilization technology of gut symbiotic microorganisms such as termite and longhorn beetle, clone types of gut microorganism complex system were analyzed to find out the diversification. In the decay of wood, co-culture of two species of mold fungus was increased in efficiency than single culture. More than 90% was classified/identified of the mold fungi accumulated (in wood piece)/separated for the utilization of plant symbiotic microorganisms. For the production of petroleum substituting useful resource, conditions were established of callus induction from immature embryos of tropical oil crops, especially oil palm, and of regeneration of a lot of small plants from the callus. To establish the Agrobacterium-mediated transformation system of oil palm, the binary vector harboring the reporter gene and selectable marker gene was constructed. Using the vector, oil palm tissues are inoculated and infected with agrobacteria. To heighten the function of palm oil, 10 particular clones were selected from the complementary DNA library obtained from oil palm fruit tissues. The genetic study of germs was also made. (NEDO)

  7. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  8. Report on a survey in fiscal 1998 for petroleum substituting energy development and utilization in the Pacific Ocean region; 1998 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    NONE

    1999-03-01

    A survey was carried out to make available the information base that can collect, put into order and provide quickly and accurately the energy related information based on global environment problems in the Pacific Ocean region. Fiscal 1998 has performed a substituting energy demand and supply analysis in the Pacific Ocean region by adding the 1996 data, in addition to collection of the normal energy data. For the purpose of analyzing the petroleum substituting energy demand and supply in the Pacific Ocean region, data were collected from 17 countries for fiscal 1997 and the quarterly data for 1998. Retroactive data collection was also continued. The growth rate of primary energy supply in the Pacific Ocean region is 1.8% in average in the 1980's, and 3.8% in the 1990's. In contrast, the growth rate of petroleum substituting energies is 6.4% in the 80's and 6.2% in the former half of the 90's, being far higher than the growth rate of the primary energy supply. The share of the petroleum substituting energies accounting for in the primary energy supply has increased from 6.7% in 1980 to 12.1% in 1996. As the breakdown, nuclear power accounts for overwhelmingly large, followed by geothermal energy and new energies. (NEDO)

  9. FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

    NONE

    2001-03-01

    The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

  10. Fiscal 2000 survey report. Survey report on development and utilization of alternative energies for oil in Pacific region; 2000 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    NONE

    2001-03-01

    A survey was conducted, with environmental matters taken into consideration, for building an information gathering infrastructure for the countries in the Pacific region, capable of promptly and accurately collecting and offering energy related information. Conducted in this fiscal year were regular data gathering, review of oil supply and demand and alternative energy supply and demand in the Pacific region, on-site survey of alternative energy development and utilization in Vietnam, quarterly analyses of trend of energy demand, and the like. The supply of primary energy in the Pacific region increased by 2.3% per year in the period 1980 through 1998. The rate of increase was the lowest with oil, and the highest with hydroelectricity, atomic power, and recoverable energies such as geothermal energy. The Vietnamese Government is promoting its efforts to develop power sources by use of recoverable energies for farm village electrification. Efforts are being earnestly exerted to develop its rich natural gas resources and it is expected that there will be a remarkable achievement in the use of alternative energies due to an increase in natural gas consumption. In the field of data collection, various data were registered with the database. (NEDO)

  11. Achievement report for fiscal 1999 on international research cooperation project. Research and development of transfer standard for oil flowmeter; 1999 nendo sekiyu ryuryokei no iten hyojunki no kenkyu kaihatsu seika hokokusho

    NONE

    2000-03-01

    Research was conducted for the development of a highly reliable flowmeter which enables the efficient calibration of flowmeters at oil plant working sites and the international comparison of oil flow standards, and is also usable as the standard of oil flow at private businesses. In this connection, international research cooperation was carried out with Physical Engineering Research Institute, Germany. In the study of rotors, tooth profiles were contrived and various analyses were conducted for each screw type. In the study of flow inside flowmeters and of structures, screw-type volumetric flowmeters of K Co. were subjected to various tests for structural analysis, and visible models were fabricated for the clarification of flow characteristics. In the study of servo systems and instrumentation, several types of pressure difference detecting mechanisms were newly contrived, and servo control systems were investigated. In the study of trial manufacture and evaluation, the UF-VI080{alpha} cast iron (FC250) rotor flowmeter and the UF-VI080{alpha} aluminum (A7075BE) rotor flowmeter were examined. Both failed to achieve the target precision of {+-}0.2% in the case of gasoline but, in the case of kerosene and heavy oil, the target levels were sufficiently met. (NEDO)

  12. Fiscal 2000 achievement report on the research and development of transfer standard gage for oil flowmeter (final assessment); 2000 nendo sekiyu ryuryokei no iten hyojunki no kenkyu kaihatsu seika hokokusho (saishu hyoka hokokusho)

    NONE

    2001-03-01

    In a servo PD (positive displacement) flowmeter for oil, a differential pressure transmitter detects difference in pressure between the PD flowmeter input and output ports and a rotor is driven by a servo motor so that the pressure difference between before and after the PD flowmeter rotor will be zero. The design enables high-accuracy measurement across a wide range of flow rates and is not easily affected by the surrounding physical conditions such as viscosity and density. For the development of such a flowmeter, it is necessary to develop a rotor that rotates smoothly free of locking in a steady and uniform flow, to build a visualized model that enables the analysis of flow inside the flowmeter which in turn will enable the determination of optimum differential pressure detecting ports, and to connect a newly developed servo mechanism to the thus determined ports. As the result of the research, a servo PD flowmeter is developed, which is a 50mm diameter prototype employing the Invoflex tooth form which is the waveform for a rotor suitable for a high performance flowmeter. Placed in a generally used oil flow calibration liquid, which is gasoline, kerosene, or the like, it covers a flow rate range of 1:10 and reads with an accuracy of {+-}0.1%. It remains stable in performance and suffers but a little change with the passage of time. (NEDO)

  13. Fiscal 1999 survey report. Survey of development and utilization of energy substitutes for oil in the Pacific region; 1999 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

    NONE

    2000-03-01

    The Pacific region is a densely populated region where economy is developing at a high pace with China and other newly industrialized economies at the core. When energy balance in the region is studied, it is found that China and some others have already turned pure importers of energy and that probabilities are high that, along with development of economy and improvement on living standards, all the nations in the region will become pure importers. Accordingly, in the presence of urgent problems of global pollution and oil resources depletion, it is important to make sure that data particularly about the development of substitute energies for oil in this region be collected and duly dealt with for accurately predicting future developments. In this survey, a database is to be built to grasp the trends of energy supply and demand with attention focused on substitutes for oil which are available at hand. In this fiscal year, data for 1997 were added to the database for analysis into demand and supply of substitutes for oil in the Pacific region, and energy data were gathered for this purpose. Detailed tables of balance were compiled, broken down by energy source. Other detailed tables of balance were also prepared, these broken down by ultimate consumption department. (NEDO)

  14. Joint Research. Report on the results of developing commercialization of a technology of process wastes and re-utilize them by using petroleum substituting energy; Kyodo kenkyu. Sekiyu daitai energy riyo haikibutsu shori saishigenka gijutsu jitsuyoka kaihatsu seika hokokusho

    NONE

    1998-03-01

    A study was conducted on a technology to melt shredder dust and non-combustible wastes directly by using coal, reduce their volume and re-utilize them. The elementary study on a high-temperature melting and treating technology set such targets as optimizing the melting and treating technology in correspondence with properties of materials to be treated, by using a small melting test plant, achieving a volume reduction rate of 1/200, and reducing treatment cost. In order to make innoxious the different kinds of environmental loading materials contained in exhaust gas from a high-temperature gasification and direct melting system, discussions were given on an optimum control condition for the exhaust gas system facilities. Furthermore, physical properties of discharges (slags nd metals) were investigated to discuss material re-utilization. In discussing optimal systems, three kinds of systems including two types utilizing fuels were proposed as high-temperature gasification and melting treatment process from a viewpoint of technology and cost. Respective systems were compared with each other on treatment cost, and their priorities were identified. 56 refs., 50 figs., 55 tabs.

  15. Fiscal 1985 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1985 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1986-03-01

    The operation continues of the experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si, and efforts are under way to carry out improvements, to verify such improvements for the results, and to develop operation control technologies. During the operation, improvements are made with respect to the length of stable operation period, granule quality, and device operation, and the results are verified. An automated control test system is verified, and a reactor tube newly developed by Shin-Etsu Chemical Company is subjected to a durability verification test. On the other hand, development is started of SiC-CVD (chemical vapor deposition) technology for materials for large reactor tubes, studies are started on a basic experimental device, basic studies are conducted for designing a large reactor, and investigations are conducted of a large plant conceptual design, an automated control system for reactors, and so forth. The results achieved are all found to be satisfactory. Above all, the granule quality is improved to be quite high in purity, and a cast cell made from improved granules exhibits a photoelectric conversion efficiency to exceed 13%. It is also found that the newly developed reactor tube is stronger than conventional reactor tubes and will be advantageous over others in the future enlargement of devices. (NEDO)

  16. Fiscal 1986 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1986 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1987-03-01

    The aim is to develop a fluidized bed reactor high in productivity and low in power consumption for the realization of mass production of low cost polycrystalline silicon usable for solar cell construction. An experimental device capable of producing 10 tons/year of SOG (spun on glass)-Si is built and operated. The fluidized bed reactor treating trichlorosilane as the material and the product quality achieve the initially set goals, and the essence is seized of operation management technology. In fiscal 1986, for development of the technology into a practical application technology, designs are prepared for a larger reactor unit and a large plant of the commercial scale. From the viewpoints of production efficiency and cost, the enlargement of a reactor unit is an inevitable task to discharge before practical application. There are two challenges to meet. One is the development of technologies for manufacturing large reactor tubes strong enough to withstand practical service and the other the development of a reactor structure fit for dimensional enlargement. It is then found that the concept of an economically optimum design relative to device series or device block formation is variable in the case of large plants, dependent on the scale of production, and that therefore it is necessary to arrange problems in a proper order to facilitate further deliberation. (NEDO)

  17. Fiscal 1982 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1982 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1983-03-01

    The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. The installation of a 10 tons/year class model plant for SOG-Si production is completed in July 1982. Flaws are removed after a test run, and four reactions are accomplished without damage on the reactor tube in the period from February-end to March-beginning marking 550 hours of operation in total. Thanks to the four operations, 1,086kg of granules are experimentally produced and an electric power consumption rate of 30.6KWH/kg Si is achieved, control of the flowing particle amount by reactor differential pressure is accomplished and the same of the yield by recovered silane liquid composition analysis, and essence is seized of operation control technologies. In an experimental apparatus for seed production, Si is crushed by a roll crusher and then subjected to separation by a quartz-made air elutriator. A high yield of 130kg is obtained after crushing for 75 hours. (NEDO)

  18. Fiscal 1983 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1983 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1984-03-01

    The effort aims to develop a reactor and its peripheral devices and process management technology therefor and to develop chlorosilane hydrogen-reduction process technology as part of the endeavors to develop a low cost production process for silicon for photovoltaic cells for the purpose of building a model plant capable of approximately 10 tons/year in terms of SOG (spin on glass) silicon. A study is made of ten operations (total reaction time of 2,264 hours), and it turns out that the electric power consumption efficiency is near the initially planned value. The yield of Si is, however, but 16.5% which is lower than the initially planned value of 20%. The value is elevated to 18% by raising the reactor temperature. To prevent overcleaning, a reactor with its internal walls experimentally coated with SiC is tested. The problems with devices other than the reactor tube are extraction rendered difficult by anomalously grown granules and processing devices choked by Si powder contained in waste gas after reaction. The first problem is settled by modifying the extraction tube but the other still needs a remedy. The produced granules are found to be high in quality. The seed producing roll crusher is operated for a total of 92 hours yielding 857kg in total. (NEDO)

  19. Fiscal 1980-1987 Sunshine Program achievement reports. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Overview: Development of technology for chlorosilane hydrogen-reduction process); 1980-1987 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jijkken seisei kensho sokatsuban (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1988-11-01

    The chlorosilane hydrogen-reduction technology development period may be divided into the first phase (fiscal 1980-1985) and the second phase (fiscal 1986-1988). During the former phase, efforts were exerted to develop a small experimental device (10 tons/year class) and technologies to operate the same. Important challenges were to cause reaction to occur only on the seed grains in the reactor and to create a proper material for the reactor tube. In the latter phase, element technologies were developed, indispensable for the development of a practical reactor. Endeavors exerted to solve these challenges were the development of a high-strength large-diameter reactor tube, the development of an SiC-CVD (chemical vapor deposition) coating technology, and the development of a technology to join parts to the ceramic-made reactor tube. After eight years' striving, a fluidized bed reactor has been successfully constructed, capable of continuously reducing trichlorosilane by hydrogen. The success promises stable production and supply of polycrystalline silicon. The SOG (spun on glass)-Si produced by the reactor is pure enough to serve the purpose of photovoltaics, and its unit cost has been lowered as initially intended. (NEDO)

  20. Fiscal 1984 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1984 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1985-03-01

    In fiscal 1984, studies are conducted for long-time stabilized operation of the device (extension of reactor tube service life, elimination of flaws in the granule extraction process, control of deposited silicon), improved granule quality (measures to deal with Cu pollution), cost reduction (improvement on yield of silicon after reaction, reduction in electric power consumption rate), and so forth. The results are found to be satisfactory in outline. The problem of strengthening the reactor tube material itself remains to be solved, however, with many knotty issues to settle before practical application. In the effort to deliberate these difficulties, as many as 4,377 hours (reaction hours) in total are spent in fiscal 1984. During the operation, 8.3 tons of granules are produced of which approximately 7 tons are fed to the next stage of processing. The quality of granules produced in this way is stable thanks to efforts to prevent pollution and to prolong continuous reaction time, and is found to satisfy NEDO (New Energy and Industrial Technology Development Organization) specifications. Furthermore, the cast cell and the ribbon cell using thus-produced granules achieve photoelectric conversion rates of 10% and 9%, respectively, thereby meeting the target goal of 9%. (NEDO)

  1. Fiscal 1987 Sunshine Program achievement report. Development for practical application of photovoltaic system (Verification of experimental low cost silicon refining - Development of technology for chlorosilane hydrogen-reduction process); 1987 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Tei cost silicon jikken seisei kensho (Chlorosilane no suiso kangen kotei no gijutsu kaihatsu)

    NONE

    1988-03-01

    Since its construction in 1982, the experimental device capable of 10 tons/year production of SOG (spun on glass)-Si has been in operation, and the trichlorosilane processing fluidized bed reactor has achieved its goals in performance and product quality. Element studies continue for the enlargement of the reactor unit for practical application and for the designing of a large plant of the commercially viable scale. In fiscal 1987, element studies are conducted for the enlargement of the reactor unit. Concerning the development of technologies for the manufacture of large reactor tubes strong enough to withstand practical application, efforts are made to strengthen materials for the fabrication of reactor element tubes (230mm and 500mm in diameter), to develop SiC-CVD (chemical vapor deposition) technology to provide reactor tube materials with resistance to corrosion, and to develop a single reactor tube structure indispensable for device enlargement. For the verification of such element technologies, in line with the study of experimental device operation capable of 10 tons/year SOG-Si production, studies are conducted on continuous stable operation technologies for the fluidized bed reactor, maintenance and improvement of product quality, and enhancement of durability of constituent parts and components. (NEDO)

  2. FY 1996 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1997-03-01

    Ti-Ni micro particle composite thick films could be synthesized using pulse evaporation type/magnetic field closed type evaporation source for both high hardness and high toughness. Corrosion resistant gradient composition thick films were obtained which change in composition from Ni to CrSi2 by on-substrate collision/serial sintering technology by micro particles produced by hybrid-plasma. The following were conducted: synthesis of micro particles by laser induction vapor phase reaction, formation of collision of airsol particles, and development of the continuous creation process of nano structure advanced materials by continuous combination of microwave sintering. As the higher-order structure control technology in the molecular beam complex reaction field, studies were made of photochemical reaction, effects of magnetic field on other-molecular reaction, and functional control technology. The molecular/higher-order structure control by photochemical reaction was an important factor for sensor function improvement of the formed thin film. Photon/pressure complex reaction field device was developed and an experiment was made on the material synthesis. The diamond/cBN solid solution synthesis, etc. were conducted and the hardness next to diamond was obtained. (NEDO)

  3. Report on achievements in fiscal 1999. Research and development of carbon-based high-function material technologies (research and development of ocean bottom petroleum production system); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    NONE

    2000-05-01

    As part of the research and development of carbon-based high-function material technologies, research and development has been performed on a material creating technology and a process technology to crease mechanically high-function materials. The former technology performs synthesis by using the electron excited CVD process and the explosion synthesizing process, intended to analyze the structure and properties thereof. It is intended to synthesize nitriding-based carbon films and elucidate their composition and structure by using the mass separation ion beam method and the laser beams. Synthesizing nano tubes by utilizing catalytic reactions, and investigating their properties are intended by using the thermal CVD process, plasma CVD process and arc discharge process. Elucidation is intended on the reaction and production mechanisms of carbon-based materials, theory estimation, structures possessed by the carbon-based materials, and mechanisms to manifest their characteristics. The latter technology relates to the three assignments subjected to a composition inclining film forming technology, a complex shaped film forming and micro processing technology, and a large area film forming technology. It is intended to utilize positively such properties as low friction and wear performance and high-temperature corrosion resistance expected in high-function carbon-based materials including amorphous carbon, diamond and nitrided carbon for the purpose of application to surface protection of movable parts in different industrial machines, and building materials including glasses. (NEDO)

  4. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  5. Fiscal 1993 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1993 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    NONE

    1994-03-01

    There was a progress in the development of oil based C/C (carbon/carbon) composite technology. Studied in a comprehensive endeavor were coordination between various technology developing activities, surveys of trends of relevant technologies, and technological tasks to discharge for the development of materials usable under extreme environments. Technologies developed for advanced composite materials involved (1) oil pitch derived random structure carbon fibers, (2) oil pitch derived onion structure carbon fibers, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. Under item (1), random structure carbon fibers were examined for high reproducibility of physical properties, continuous surface coating technology for fibers, and weavability. Under item (2), onion structure carbon fibers were studied for development into C/C composite reinforced fibers. Under item (3), the mechanical structure of double structure carbon fibers was clarified, and C/C composite materials were fabricated using experimental prepregs worked out after studying matrix composition and impregnation techniques. (NEDO)

  6. Research and development project for large industrial technologies in fiscal 1992. Achievement report on research and development of an advanced function creating and processing technology (Development of a technology to prevent corrosion in petroleum production systems); 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1993-03-01

    In order to enhance durability and safety of members used in ocean bottom petroleum collecting systems, researches were made to create materials having excellent corrosion resistance, strength and heat resistance. In the research of a gas sensor to measure nature of drilled mud water, high corrosion resistance and sensitivity improvement in an infrared gas sensor was attempted through research and development of a high-purity and high-quality film forming technology. In the research of an inclination structure creating technology, researches were made on an interface control technology to enhance adhesion of substrates with ultra fine particle complexes. Developmental research was performed on materials by synthesizing the ultra fine particle complex and by injecting ions into the surface layer. In developing thick ceramics film or bulk having high functions, researches were carried out on a synthesizing technology using compound plasma, and a synthesizing technology using compound laser. In synthesizing high-function organic materials, researches were performed on a high-order structure control technology using the molecular beam compound reaction field, and on a material synthesizing technology using the photon compound reaction field and the interface compound reaction field. A compound reaction field diagnosis technology using the laser ionizing process was studied as a supporting technology. (NEDO)

  7. FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology for corrosion prevention of the petroleum production system; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1994-03-01

    In the study of a corrosion resistant high sensitivity gas sensor, the following two technologies are needed: decrease in impurities of materials for super-higher purity, and formation of films with physically high quality such as orientation and homogeneity. Experiments were made on laser excitation separation refining, CVD, laser ablation, super-high vacuum, etc. For the stabilized formation of high-adhesion thin/thick films, studies were carried out of the surface activation for processing substrate surface before film formation, interface counter diffusion in thin film formation process, and the technology for combination of these. The higher-order structure control of materials was attempted using the reaction field combined with the photochemical reaction by the high grade photon field, based on the molecular beam vapor-deposition technology under super-high vacuum. In the synthesis of materials by the photon combined reaction field, studies were made of the design/process of a dynamic device which reacts like pulse the photon/high pressure/strong magnetic field on carbonaceous materials and a static combined reaction field device by the stationary high pressure field. A study was commenced of a synthesis method in relation to fullerene with a new structure which has unique characteristics. (NEDO)

  8. Report on achievements in fiscal 1999. Research and development of synergy ceramics (research and development of technologies to prevent corrosion in petroleum production systems); 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu

    NONE

    2000-03-01

    This research and development has been performed on the following themes: 1. Material realizing technology, and advanced evaluation and design technology (1-(1) ultra precision materials, 1-(2) high-temperature energy materials, 1-(3) basic member design technology, 1-(4) materials having function to detect stresses and micro destruction, 1-(5) porous materials to control gas hole patterns, and 1-(6) materials having self-restoring/self-lubricating function); 2. Application technology (2-(1) materials having substance and light selecting function, 2-(2) high wear resistant and easy-to-process materials, 2-(3) high-performance resistance materials for electric power devices, and 2-(4) flexible sliding materials); 3. Formation of common base technologies. 4. Report on achievements in countries making joint researches. In Item 1-(1), micro destruction mechanisms were analyzed, and the directionality of material structure control was clarified. In Item 1-(2), controlled closing holes were introduced. In Item 1-(3), polycrystalline alumina, polycrystalline zirconia, and zirconia particle dispersed alumina were evaluated microscopically and macroscopically. In Item (4), Y-TZP/Ni nano-compound materials were fabricated successfully. In Item 1-(5), destruction behavior of porous ceramics was studied. In Item 1-(6), characteristics were investigated on Fe(Al)Al2O3 which was fabricated on the trial basis. (NEDO)

  9. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

  10. FY 1991 Report on the results of the research and development of the processing technologies for creating advanced functions. Development of the technologies for preventing corrosion of oil production systems; 1991 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisan system fushoku boshi gijutsu kaihatsu

    NONE

    1992-03-01

    The research and development project has been started to develop the technologies for superhigh-purity separation/processing; controlling ultrafine crystal particles, including creating composites by the aid of a plasma laser; synthesizing highly functional organic materials; and supporting these technologies, for creating functions, e.g., advanced sensing functions, highly functional electromagnetic characteristics, and corrosion resistance, heat resistance and high strength. The R and D program for the technologies for superhigh-purity separation/processing covers development of highly corrosion-resistant, high-sensitivity gas sensors and highly functional thin oxide film sensors. The R and D program for controlling ultrafine crystal particles covers the researches on the technologies for creating inclined structures by the ion composite vapor-phase process, and the technologies for producing composites by the aid of a plasma laser. The R and D program for the organic material synthesis technologies includes researches on the technologies for controlling higher structures in a molecular beam composite reaction field, and on the technologies for synthesizing materials in a photon composite reaction field and in an interfacial composite reaction field. The R and D program for the supporting technologies includes the researches on the technologies for diagnosing a composite reaction field by the laser-aided ionization method. In the FY 1991, which is essentially the first year for the project, the efforts are directed to designs and construction of the required facilities, and preliminary tests. (NEDO)

  11. Fiscal 1991 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1991 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    NONE

    1992-03-01

    Development of oil based C/C (carbon/carbon) composite technology was carried out. In a comprehensive survey, studies were conducted of the trends of associated technologies and tasks to discharge for the development of materials usable under ultrahigh temperature environments. For the development of advanced composite materials, efforts were exerted to develop technologies in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), physical properties and the like of a specimen fiber were clarified by studying conditions for manufacturing random structure carbon fibers, and the specimen was provided with a surface coating for the study of oxidation resisting performance improvement. In Field (2), onion structure carbon fiber forming conditions and basic technologies for structure manifestation were established, and basics of fiber surface coating technology were studied. In Field (3), double structure carbon fiber forming conditions were studied, specimen fabrication was carried out, and fiber surface coating technology was studied. (NEDO)

  12. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  13. Fiscal 1990 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1990 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    NONE

    1991-03-01

    Efforts were made to develop technologies of oil based C/C (carbon/carbon) composites. In a comprehensive survey, studies were conducted of the trends of associated technologies and tasks to discharge for the development of materials usable at ultrahigh temperatures. For the development of advanced composite materials, efforts were exerted to develop technologies in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), random structure fiber manufacturing conditions were studied, basics of their relations with fiber thermal properties and the like were understood, carbon fibers were provided with surface coating, and studies were made to enhance the oxidation resistance of carbon fibers. In Field (2), fiber forming conditions were studied and their relations with fiber physical properties, such as strength, in an oxidizing atmosphere were grasped. In Field (3), manufacturing conditions and their relations with fiber physical properties were learned, and a technology was developed to manufacture composite rods. (NEDO)

  14. Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    NONE

    1998-03-01

    Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

  15. FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    NONE

    1998-03-01

    Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

  16. Fiscal 1989 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1989 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkhyu kaihatsu

    NONE

    1990-03-01

    The research and development of advanced composite materials succeeds the composite material development project initiated in fiscal 1981, and activities were conducted in the two domains of advanced composite material development and comprehensive survey implementation. In the comprehensive survey, trends of associated technologies were investigated, and technical tasks were studied relative to the development of advanced materials. In the effort to develop advanced composite materials, activities were conducted in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), relations between conditions of forming carbon fibers out of pitch and carbon fiber random structure were elucidated, and development was started of technologies for providing fibers with oxidation resisting surface coatings. In Field (2), relations between conditions of forming carbon fibers out of pitch and carbon fiber onion structure were elucidated, and development was started of technologies for providing fibers with oxidation resisting surface coatings. In Field (3), efforts were started to elucidate oxidation resistance governing factors. (NEDO)

  17. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  18. Project to aid development of an oil substituting fuel manufacturing technology in fiscal 1998. Report on the result of developing a technology to make cable covering materials into fuel; 1998 nendo sekiyu daitai nenryo seizo gijutsu kaihatsu hojo jigyo. Densen hifukuzai nenryoka gijutsu kaihatsu

    NONE

    1999-03-01

    Research and development have been carried out with an objective to re-utilize waste cable covering materials as oil substituting energy. The research has been performed on behavior of chlorine and lead being substances that impede making the cable covering materials into fuel, development of a technology to remove chlorine, lead and copper, and pelletizing properties for fuel making. In the study of behavior of chlorine and lead, the following matters were made clear: dechlorination reaction completes within 30 minutes if pyrolysis temperature is higher than 300 degrees C; the more the amount of filler CaCO3 in test samples, the less the dechlorination amount; and secular deterioration does not affect the dechlorination amount. A technology has been developed successfully to remove the substances that hinder making the cover materials into fuel, achieving the target values of copper at 0.2% or less, lead at 0.3% or less, and chlorine at 5% or less. In developing the pelletizing technology that puts the cover materials into raw materials for blast furnaces, dechlorination rate of 90% was achieved by mixing coke/PVC at a ratio of 1/1 and dechlorinating it by using a rotary kiln. It was verified that the product is free of problems in particle size as the blast furnace raw material. (NEDO)

  19. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  20. Fiscal 1998 industrial science and technology R and D system. R and D report on human media / R and D on the advanced information system technology for oil refinery plants; 1998 nendo seika hokokusho. Human media no kenkyu kaihatsu, sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu

    NONE

    1999-03-01

    As a part of R and D on human media, this report describes the fiscal 1998 result on development of the advanced information system for oil refinery plants. The R and D on human media have been promoted toward construction of a new information system around human beings by advanced integrated media technology since fiscal 1994. The whole concept is body sensation-, heart sensation- and knowledge- friendly media. For safe operation of oil refinery plants, this project develops (1) the intelligent monitoring of measuring instrument information and image information, (2) the display and guidance for facilitating collection of operation data by operator, (3) the modeling for efficient management of previous data and their effective use for current operations, and (4) the autonomous cooperative control technology. In fiscal 1998, the following subsystems were designed and prepared: The interface agent, virtual plant display interface, semantic representation interface, ontology, distributed cooperative processing technology, plant model and interface system. (NEDO)

  1. Fiscal 1991 research report. Research trend survey for next-generation industrial structure technology research and development project - Research and development of advanced materials for extreme environments; 1991 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu project ni kakawaru kenkyu doko chosa hokokusho. Chotaikankyosei senshin zairyo no kenkyu kaihatsu (sekitoku sekiyu)

    NONE

    1992-03-01

    Efforts were exerted to develop intermetallic compounds and advanced C/C (carbon/carbon) composite materials usable under extreme environments such as high temperatures. In relation with advanced composite materials, especially with projects for developing composite materials using oil as raw material, a survey was conducted of the three fields of (1) summarization of activities conducted up to fiscal 1991, (2) contents of associated aerospace projects, and (3) oil based composite material technology. In Field (1), past achievements are summarized. In Field (2), aerospace projects under way across the world are broken down by airframe and engine, and are reviewed from the viewpoint of needs for materials. In Field (3), the present and future of heat resisting thermosetting composite materials, thermoplastic composite materials, and C/C composites are discussed. Characteristics such materials are supposed to finally assume and tasks to discharge for technical development are also taken up. (NEDO)

  2. FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

    NONE

    1999-03-01

    For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

  3. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    NONE

    2000-03-01

    For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

  4. FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

    NONE

    2000-03-01

    For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

  5. Study of the ablation of extra-low temperature aggregate target and the development of technology of formation of non-equilibrium high-quality functional thin films by the plume control; Gokuteion gyoshutai target no abureshon oyobi purumu seigyo ni yoru hiheiko kohinshitsu kinosei usumaku seisei gijutsu kaihatsu ni kansuru kenkyu

    NONE

    1997-03-01

    A study was made on factors of the formation of high-quality thin films in the pulse laser deposition (PLD) method, a synthesis method of high-grade functional material thin films. In the experiment, plume current measurements using Cu target were conducted for the control of electric and magnetic fields. Especially, the measuring evaluation was made of the two-dimensional distribution including not only the central part of the substrate placed opposite to the target, but the periphery of the substrate. As a result, the following was found out. The distribution of charged particles in the plume is different in positive charge and negative charge, and the negative charge is dispersed/distributed more widely. Accelerating/decelerating effects of charged particles by the electric field are saturated when the bias voltage absolute value is approximately 100V. Ionization is promoted by giving the magnetic field, and the plume distribution is expanded. Positive charged particles of the plume in the magnetic field are decelerated. In the distribution control by giving the electric field, it is effective to think improvement of the distribution not by attracting charged particles by the electric field, but by shutting out charged particles of the same polarity. 29 refs., 75 figs., 2 tabs.

  6. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Commercialization of depth dechlorination/debromination refining catalyst of waste plastic derived oil and the liquefaction process; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu bun'ya. Hai plastic bunkaiyu no shindo datsuenso dasshuso seisei shokubai oyobi yuka process no jitsuyoka (dai 1 nendo) seika hokokusho

    NONE

    2001-03-01

    The development was proceeded with of technology to produce iron oxide/porous carbon composite catalyst which promotes dehalogenation of thermal-degraded oil at low cost and in large quantity. This catalyst enables the improvement in operability and safety in the liquefaction process for mixed plastic and in quality of oil product. The development is also made of a regional distributed small batch liquefaction system with processing ability of 1t/day. Studies were made in the following 6 fields: 1) analysis of the dehalogenation performance of catalyst and the evaluation; 2) development of a method to industrially produce halogen compound refining catalyst; 3) R and D of a method to analyze environmental components; 4) evaluation study of halogen resistant materials and halogen resistant technology; 5) development of a small test device for commercialization of the liquefaction/degradation process; 6) comprehensive investigational study. In 1), the performance of prototype catalyst was confirmed, and the structure was analyzed. Also developed was iron chloride/SiO{sub 2} catalyst which converts organic halogen to inorganic halogen. (NEDO)

  7. NEDO Forum 2001. Session on development of geothermal energy (Prospect of geothermal energy); NEDO Forum 2001. Chinetsu kaihatsu session (chinetsu energy no tenbo)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Director Noda of Institute for Geo-Resources and Environment, National Institute of Advanced Industrial Science and Technology, delivered a lecture entitled 'Future course of geothermal technology development,' and Executive Director Iikura of Tokyo Toshi Kaihatsu, Inc., a lecture entitled 'Thinking of geothermal energy.' Described in an achievement report entitled 'Present state and future trend of geothermal development' were the present state of geothermal power generation and characteristics of geothermal energy, signification of the introduction of binary cycle power generation, and the promotion of the introduction of ground heat utilizing heat pump systems. Stated in a lecture entitled 'Geothermal development promotion survey' were the geothermal development promotion survey and its result and how to implement such surveys in the future. Reported in a lecture entitled 'Verification survey of geothermal energy probing technology and the like and the development of geothermal water utilizing power plant and the like' were reservoir fluctuation probing, deep-seated thermal resource probing and collecting, 10-MW class demonstration plant, Measurement While Drilling System, and a hot rock power generation system. (NEDO)

  8. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO (book on the handling / gas lift system). Report on the results of the R and D of the overall base technology of ocean resources (R and D of submarine oil drilling technology, etc.); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shine Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kaiyo shigen sogo kiban gijutsu no kenkyu kaihatsu (kaitei sekiyu kussaku gijutsu nado kenkyu kaihatsu) seika hokokusho (handling / gas lift system hen)

    NONE

    1998-03-01

    The paper conducted a R and D on the handling of drilling equipment in drilling/collecting of submarine oil and the gas lift of artificial oil extraction technology. As to each equipment of a barge style handling system, conducted were assembly/adjustment/trial run on land and pipe handling experiments on sea. In the experiment, confirmed were pipe transfer function, lifting function, fitting function, grasping function, etc. In the ocean experiment, studied were pipe bending stress, Karman vortex control effects, etc. Relating to the gas lift system, experiments were made on confirmation of fabrication/performance of air compressor. Moreover, a technique of air transportation to the blowing inlet of the gas lift pipe was established by developing an air blowing system and fabricating a long-distance flexible pipe. Concerning the gas/liquid/solid three-phase separator, a cyclone separator was developed, and improvement in lifting efficiency was confirmed. Helped by these, the problems of the gas lift system were almost solved, and a possibility of the commercial-base production system was obtained. 2 refs., 182 figs., 47 tabs.

  9. Report on achievements in fiscal 1999. System technology to create living environment of human activity compatible type (development of high-level petroleum plant information system); 1999 nendo ningen kodo tekigogata seikatsu kankyo soshutsu system gijutsu seika hokokusho. Sekiyu plant kodo johoka system gijutsu kaihatsu

    NONE

    2000-06-01

    This research and development project divides largely the behaviors appearing in a daily life into movement behavior and operation behavior. The research and development is executed by dividing the subject into development of a behavior supporting technology intended for the movement behavior and development of a behavior supporting technology intended for the device operation. In developing the movement behavior adapting technology, behavior scenes in a house are taken up as the important scenes to obtain peace of mind in the daily life, and construction work behavior scenes are taken up, in which environment and work contents change from moment to moment. Then, development works are carried out on the following technologies: a technology to measure on site the human behaviors and physiological conditions, a technology to understand and accumulate the behavior contents, and a behavior supporting technology to assure relief and safety by means of abnormality notification and risk avoidance. This paper summarizes the research achievements in fiscal 1999 on research and development of the movement behavior adapting technologies. Chapter 1 reports the research and development on a technology to adapt behaviors in the behavior scenes in a daily life. Chapter 2 describes the research and development on a technology to adapt behaviors in the behavior scenes in construction works. Chapter 3 reports the result of surveys on the research movements in the present research areas. (NEDO)

  10. FY 2000 report on the results of the research and development project for the photon-aided instrumentation and processing technologies. Research and development of the advanced instrumentation and processing technologies for oil production systems; 2000 nendo photon keisoku kako gijutsu seika hokokusho. Sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu

    NONE

    2001-03-01

    Described herein are the FY 2000 results of development of the photon-aided instrumentation and processing technologies, as part of development of the advanced instrumentation and processing technologies for oil production systems. The program for the microscopic processing technology combines iodine and YAG laser beams as the high-power laser beams of wavelength of the order of 1{mu}m, in order to realize laser-aided welding of high-quality thick plates, the welding demonstration tests producing good results; improves an in-process monitoring sensor, to confirm its high reliability; and improves size controllability for ultrafine semiconductor particles for development of quantum functional optoelectronic devices, and extends the electric conductivity for production of the transparent conducting films. The program for the non-destructive composition measuring technology develops a light source which produces short wavelength ray of sufficient brightness; produces three-dimensional CT images with a resolution of 2{mu}m, and is developing superconducting X-ray detectors. The program for the high-power all-solid-state laser technology starts development of a rod-type oscillation-controlling laser which can provide mixed operations of CW, pulsed and Q-switched oscillation modes at an average power of 1kW level. The program for the tightly-focusing all-solid-state laser technology develops the prototype of disk type fiber laser using silica fibers of rectangular cross-section, which produces a power of 103W, and starts development of a laser diode. (NEDO)

  11. Report on achievements in fiscal 1999 on research and development of human media under the industrial and scientific technology research and development institution. Research and development of a high-level petroleum plant information system technology; 1999 nendo human media no kenkyu kaighatsu seika hokokusho. Sekiyu plant kodo johoka system gijutsu kenkyu kaihatsu

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1999 on development of a high-level petroleum plant information system technology as part of the research and development of human media. Structuring has been performed on a prototype system comprising two stages: the phase 1 system of the single-element concentration and control type and the phase 2 system of the multi-agent type for the original fusing purpose. Relative to the interface agent, development has been made on a function for fusing, voice interactive function was realized, and personifying agent function was operated on a trial basis. In addition, a database server for large-scale cases was developed. Coordination with other agents and interactive operation were realized by making autonomic the hypothetical plant display interface. Dynamic task sharing was realized by means of discrete coordination processing. A server and a message producing system were completed, by which the processing can be progressed in coordination by having multiple number of agents share the ontology and the object models based thereon. The definition display interface was mounted for the discretely coordinating environment. (NEDO)

  12. Fiscal 1998 industrial science and technology R and D project. Research report on R and D of genome informatics technology (Development of stable oil supply measures using complex biosystem); 1998 nendo genome informatics gijutsu kenkyu kaihtsu seika hokokusho. Fukugo seibutsukei riyo sekiyu antei kyokyu taisaku kaihatsu

    NONE

    1999-03-01

    This report describes the fiscal 1998 result on development of genome informatics technology. As comparative analysis technique of genes, the combination of electrophoresis and PCR was used. For improvement of the throughput and reproducibility of the technique, module- shuffling primers were used, and the multi(96)-arrayed capillary fragment analyzer was devised. The system detecting SNPs rapidly was also developed successfully. As analysis technology of DNA sequence by use of triple- stranded DNA formation, study was made on construction of long cDNA libraries, selective subtraction of specific sequences from libraries, and the basic technology of homologous cloning. Study was also made on each reaction step of IGCR technique for fast analysis, and specifications of a fluorescence transfer monitor. As modeling technique of genetic sequence information, the simulation model was developed for gene expression regulatory networks during muscle differentiation, and feedback regulation of period genes. Such support systems as transcription factor prediction and gene regulatory network inference were developed from existing data. (NEDO)

  13. FY 1992 report on the results of the demonstration test on the methanol conversion at oil-fired power plant. Developmental study of a methanol engine system for power generation; 1992 nendo sekiyu karyoku hatsudensho metanoru tenkan tou jissho shiken. Hatsuden you metanoru enjin system no kaihatsu kenkyu hokokusho

    NONE

    1993-03-01

    For the purpose of establishing the methanol engine technology for promotion of methanol introduction to oil-fired power plant, an experimental study was made, and the FY 1992 results were summarized. In the study of technology development, the following were carried out: evaluation of durability of multi glow plug and development of high-durability glow plug, confirmation of potentiality of the laser ignition system by element evaluation test, evaluation/improvement of durability of the injection system and development of injection pump for the actual machine, trial manufacture of the 2-stage injection system and confirmation of characteristics, study of improvement in ignitability/combustion state by optimization of the temperature of glow plug, compression rate, etc., evaluation of durability of combustion chamber, etc. by the heat load measuring test and heat balance, etc. As a result of the engine test, the pump housing stayed favorable without damage in the use of about 20,000h, plunger assembly did in the use of about 4,500h, and valve assembly did in the use of about 20,000h. As to the manufacture of the actual machine, a prototype was designed/manufactured of a 500kW class direct injection 4 cycle supercharging 6 cylinder methanol engine. (NEDO)

  14. Achievement report for fiscal 1998. Photon-aided measuring and processing technologies (Research and development of advanced measuring and processing technologies for oil production system); 1998 nendo foton keisoku kako gijutsu seika hokokusho. Sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu

    NONE

    1999-03-01

    Research and development was conducted of photon-aided measuring and processing technologies and of the technology of generating photons, all these usable in oil digging. In the research and development of high-reliability laser welding technology, it was found that reflection from the keyhole served as an indicator betraying instability if any in laser welding, and this enabled the establishment of a method for observing defects in welded sections. In the research and development of technologies for measuring internal transmission of short-wavelength radiation and for photoelectron spectroscopy, a high-efficiency continuous generation of hard X-rays was noticed in the former while, in the latter, the soft X-ray source in a light source was evaluated. In addition, a photoelectron flight tube was fabricated, and evaluated. In the research and development of fiber laser, a fiber structure type was decided to be used, and fiber laser was successfully oscillated for the first time in the world. In the research and development of high-performance laser diodes, a laser diode device was fabricated as the first step in this effort. A discussion was made about a high-efficiency combination of heat sink materials, lamination and assembly system, and fibers, which was for achieving higher performance. (NEDO)

  15. FY 1999 report on the results of the R and D of genom informatics technology. Development of measures for stabilized supply of petroleum using compound living organisms; 1999 nendo genom informatics gijutsu kenkyu kaihtsu seika hokokusho. Fukugo seibutsukei riyo sekiyu antei kyokyu taisaku kaihatsu

    NONE

    2000-03-01

    In this R and D, studies were made on the following: 1) comparative analysis of genes - a system based on PCR coupled with high-speed and high-throughput fragment analyzer; 2) development of the system which detects SNPs rapidly; 3) study of the technique for DNA analysis and comparison of DNA sequence by use of the triple-stranded DNA formation; 4) improvement of a genomic DNA subtraction method, the In-Gel Competitive Reassociation technique; 5) development of computer simulation system which has capability of predicting changes in gene expression; 6) development of a workbench system assisting at gene regulatory network construction; 7) analysis of a gene expression control network; 8) general R and D issues. In 1), PCR method was developed to confirm the principle. In 2), micro plant was developed. In 3), new long cDNA library was constructed. In 4), basic experiment on FRET technology was conducted. In 5), basic model was developed of clock gene expression oscillation simulation. In 6), system was developed of gene information subtraction. In 7), workbench was designed for support of transcription control network analysis. (NEDO)

  16. Report on a survey in fiscal 1999. Survey on trends in developing innovative technologies related to reducing CO2 emission in departments consuming great quantity of energy, such as petrochemical industry; 1999 nendo sekiyu kagaku kogyo nado energy tashohi bumon ni okeru CO{sub 2} sakugen ni kansuru kakushinteki gijutsu kaihatsu doko chosa hokokusho

    NONE

    2000-03-01

    A survey was performed on the state of developing energy saving and CO2 emission reducing technologies in the following fields: (1) distillation technologies, (2) combustion technologies, (3) heat transfer and conduction technologies, and (4) technologies to convert and fix generated CO2. While the technologies in the field (1) are of the matured domain, technologies providing 20 to 60% energy saving effect have been developed. In the field (2), gas turbine combustion can achieve an overall plant thermal efficiency of 50% or more, whereas a trial calculation indicates that CO2 emission can be reduced by 22%. Catalytic combustion is noticed as a measure to make low NOx emission possible. A composite type catalytic combustor for gas turbines demonstrated that NOx emission of less than 5 ppm can be achieved. In the field (3), energy saving effect higher by 52% than in the warm wind room heating system has been obtained. Development has been made on heat storing materials that have phase change temperature of higher than 80 degrees C and large latent heat storage quantity. In the field (4), researches are advanced in a TiO{sub 2} catalyst that uses sunlight. A catalyst that is methanated at high speed with CO2 conversion rate at nearly 100% has been developed. In methanol synthesis, a catalyst that has high selectivity even at low temperatures has been developed. (NEDO)

  17. FY 1999 Report on research and development results of photon-applied instrumentation/processing technologies. Research and development of advanced measuring/processing technologies for oil production systems; 1999 nendo foton keisoku kako gijutsu seika hokokusho. Sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development of photon (laser) beam utilization as part of the R and D project of the advanced measuring/processing technologies for oil production systems. For the high-reliability laser welding technology, the tests are conducted for welding 15 mm thick steel plates and 5 mm thick aluminum alloy plates by synthesized iodine/YAG laser beams, producing high-quality welding results. For the microscopic processing technology, attempts have been made for development of quantum functional optoelectronic devices which have nanometer-sized ultrafine dots. For the non-destructive composition measuring technology, the internal transmission measurement program produces the target light quantity by increasing brightness of the short-wavelength light source. The three-dimensional digital tomography (DT) images with a space resolution of several micrometers are obtained. For the tightly-focusing all-solid-state laser technology, a fiber-structured fiber laser is developed, on a trial basis, to attain a power of 15 W. A high-power, high-brightness laser diode, required for exciting the fiber laser is developed, and a power of 30 W or more is obtained by an InGa(As)P device. The comprehensive investigation results are also presented. (NEDO)

  18. Public subscription project for international joint research proposals in fiscal 2000 - public subscription of international proposal (Substitution No.2). Report on achievements in developing technologies to produce oil-alternative energies from fibrous material based biomass and industrial wastes; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (daitai No.2). Sen'ishitsukei biomass oyobi sangyo haikibutsu kara no sekiyu daitai energy seisan gijutsu no kaihatsu seika hokokusho

    NONE

    2001-03-01

    Development has been advanced on technologies to manufacture methanol efficiently by combining a technology to convert selectively fibrous material based biomass into sugar under high concentration sulfuric acid condition with the immobilized enzyme flash fermentation process, both being developed in the United States. Activities have been taken in the following three fields: 1) establishment of an optimal biomass treatment condition by using concentrated sulfuric acid, 2) chromatographic separation of sugar and sulfuric acid, and 3) discussions on conditions to apply the immobilized enzyme flash fermentation process. In Item 1), discussions were given, using rice straw and waste woods as the object, on effects of biomass particle size, sulfuric acid to biomass feeding ratio, sulfuric acid concentration, reaction temperature and time on the cellulose to hemicellulose reaction ratio and the sugar conversion factor, whereas it was revealed that the governing factors are the biomass/sulfuric acid contact area and the reaction temperature. In Item 2), a chromatographic device filled with anion ion exchange resin was used to set the sugar recovery rate of 100% and the sulfuric acid recovery rate of 93%. (NEDO)

  19. Chronology of petroleum geophysics; Sekiyu butsuri tansa nenpyo

    Kametani, T

    1996-10-01

    A table, chronology of petroleum geophysics in overseas and in Japan, has been prepared for the convenience of checking events, which are thought to be important as notable affairs in application, success, and technical innovation. In overseas, successes in the 1920s were remarkable, when the US modern geophysical exploration made a start. Successes in determining the position of exploratory drilling by means of the gravity torsion balance, fan shooting seismic refraction method, and seismic reflection method occurred one after another. The USA has kept its situation stably as the number one by the seismic reflection method occurred most lately, and its life has been further elongated by adopting digital techniques. The CDP technique which became to be used simultaneously, and the seismic sources without using explosives, such as vibro-seismic source and air gun, extended the success of digital techniques drastically. In the future, the progress of 3-D exploration technology is expected. In Japan, about 18 years lag in the seismic reflection method is observed when compared with the USA. Japan has provided leading techniques in the shallow layer seismic reflection method and S-wave exploration. 40 refs., 1 tab.

  20. Volatiles production from the coking of coal; Sekitan no netsubunkai ni okeru kihatsubun seisei

    Yamashita, Y.; Saito, H.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and volatiles were produced continuously at a temperature raising rate of 50{degree}C per minute, and at 3{degree}C per minute, the production of the coke and volatiles progressed stepwise as the temperature has risen. 7 refs., 6 figs.

  1. Acetaldehyde formation from ethanol over titanium dioxide photocatalyst. Nisanka titan hikarishokubai ni yoru ethanol kara no acetaldehyde no seisei

    Iseda, K [Government Industrial Research Institute, Nagoya, Nagoya (Japan)

    1990-02-20

    The suspention of TiO {sub 2} (rutile structure, 99.9%, 300 mesh) photocatalyst in ethanol was irradiated under ultraviolet light in an argon atmosphere at 25 centigrade. Acetaldehyde, methane and hydrogen were detected as products. When the photocatalysis of TiO {sub 2} itself was examined comparing with the result of blank test without using catalyst, the activity of TiO {sub 2} was confirmed only for the formation of acetaldehyde among the products. The yields of acetaldehyde increased with increasing addition of catalyst. The increasing rate of methane yields was rather small and the methane yields were lower than those in the blank tests. The hydrogen yields were almost same as in the blank tests. Acetal was formed in the blank test but was not formed with addition of TiO {sub 2}. It was provided that TiO {sub 2} was an effective catalyst for the formation of acetaldehyde. 6 ref., 5 figs.

  2. Study of nozzle deposit formation mechanism for direct injection gasoline engines; Chokufun gasoline engine yo nozzle no deposit seisei kaiseki

    Kinoshita, M; Saito, A [Toyota Central Research and Development Labs., Inc., Aichi (Japan); Matsushita, S [Toyota Motor Corp., Aichi (Japan); Shibata, H [Nippon Soken, Inc., Tokyo (Japan); Niwa, Y [Denso Corp., Aichi (Japan)

    1997-10-01

    Nozzles in fuel injectors for direct injection gasoline engines are exposed to high temperature combustion gases and soot. In such a rigorous environment, it is a fear that fuel flow rate changes in injectors by deposit formation on nozzles. Fundamental factors of nozzle deposit formation were investigated through injector bench tests and engine dynamometer tests. Deposit formation processes were observed by SEM through engine dynamometer tests. The investigation results reveal nozzle deposit formation mechanism and how to suppress the deposit. 4 refs., 8 figs., 3 tabs.

  3. Fiscal 1993 report on the separation/refining technology section meeting; 1993 nendo bunri seisei gijutsu bukai hokokusho

    NONE

    1994-03-01

    Group activities in fiscal 1993 are reported. In the study of hydrogenation refining of the naphtha fraction under the project for 'the upgrading of coal oil and the development of oil blending technology,' a hydrogenation experiment is conducted for deheterocyclicity for in the naphtha fraction (90-180 degrees C). The neutralization process is found to greatly accelerate denitrification, multiplying the rate constant 2-5 times at 300 degrees C. In the research and development of application technologies, the ASTM-D4625-86 method is applied to the storage test of crude oils such as naphtha from liquefied Yallourn coal, kerosene, and light oil, and the results are compared with those from natural storage. It is then found that this acceleration test is applicable even to oils from coal liquefaction. In the research and development of novel catalysts, it is found, relative to the 1st-stage hydrogenation catalyst, that an increase in the amount of supported tungsten enhances the activity and life of the catalyst and, relative to the 2nd-stage hydrocracking catalyst, that YD zeolite is effective in prolonging the life of the catalyst. (NEDO)

  4. Econometric analysis on oil-substituting energy; Sekiyu daigae energy keiryo bunseki chosa

    1992-03-01

    This is a fiscal 1991 report on the investigation having been carried out for the past 6 years by the Institute of energy Economics contracting with NEDO. The report is to make an overall evaluation of various aspects seen in the development of petroleum substitution energy in relation with the environmental problem. Various kinds of simulations are conducted by developing the industrial related model which can analyse effects of CO{sub 2} emmission control measures exerted on Japan{prime}s microeconomics such as the industrial structure, based on the analytical model which was developed by the fiscal 1990. For example, in establishment of 4 cases such as a standard case, a carbon tax imposition case, an industrial structure arrangement case and a high efficiency-new energy promotion case, signs are seen like that the primary energy supply in 2010 will decrease with heightening of energy price and improvement of consumption efficiency from 740 million kl in crude oil in the standard case to 620 million kl in the high efficiency-new energy promotion case, and CO{sub 2} emission will decrease from 440 million tons to 350 million tons. 14 refs., 65 figs., 114 tabs.

  5. Econometric analysis on oil-substituting energy. Sekiyu daigae energy keiryo bunseki chosa

    1992-03-01

    This is a fiscal 1991 report on the investigation having been carried out for the past 6 years by the Institute of energy Economics contracting with NEDO. The report is to make an overall evaluation of various aspects seen in the development of petroleum substitution energy in relation with the environmental problem. Various kinds of simulations are conducted by developing the industrial related model which can analyse effects of CO{sub 2} emmission control measures exerted on Japan{prime}s microeconomics such as the industrial structure, based on the analytical model which was developed by the fiscal 1990. For example, in establishment of 4 cases such as a standard case, a carbon tax imposition case, an industrial structure arrangement case and a high efficiency-new energy promotion case, signs are seen like that the primary energy supply in 2010 will decrease with heightening of energy price and improvement of consumption efficiency from 740 million kl in crude oil in the standard case to 620 million kl in the high efficiency-new energy promotion case, and CO{sub 2} emission will decrease from 440 million tons to 350 million tons. 14 refs., 65 figs., 114 tabs.

  6. Effect of water pollution on marine organisms; Sekiyu osen no kaiyo seibutsu eno eikyo hyoka

    Ogata, M. [Okayama Univ., Okayama (Japan); Fujisawa, K. [Okayama Prefectural Fisheries Experiment Station, Okayama (Japan)

    1997-10-10

    Toxicity of petroleum component to aquatic organisms appears as a result of its deposition onto living organisms followed by its migration into bodies of the organisms, and emergence of toxicity from the migrated component. Effect evaluation processes standing on this viewpoint may include the exposure monitoring or migration monitoring, in which the petroleum component migrated into marine organisms is analyzed and the state of the component concentrated in these organisms is measured, or effect monitoring, in which actions of the petroleum component in the organisms are investigated. The effects of petroleum on aquatic organisms would include the following occurrence: direct fatal toxicity acting on cells and membranes, quasi-fatal toxicity causing death indirectly through feeding actions and abnormal actions, direct coating of oil on surface of organisms, which prevents movability and feeding actions of the organisms and reduces hydrophilicity of plumes and hairs, pollution of living organisms due to migration of carcinogenic aromatic compounds into bodies of the living organisms, and change in species compositions and geographic distribution of living organisms due to change in physico-chemical environment. This paper explains cases of detection and identification of organic sulfur compounds, aromatic compounds, polycyclic aromatic compounds, paraffins, olefins and heavy metals in parametric compounds of petroleum. 20 refs., 4 figs., 3 tabs.

  7. Petroleum substitution energy measuring analysis survey; Sekiyu daitai energy keiryo bunseki chosa

    NONE

    1998-03-01

    For analytical evaluation of effects of environmental protection measures, energy conservation measures, new energy promotion measures, etc., a very-long term energy supply/demand model was developed and used for a simulational study. The model is composed of the models of macro economics, secondary energy prices, new energy introduction, and energy supply/demand. The feature is that the amount of new energy introduction is measuringly analyzed based on the cost and market scale, and integratedly estimated in a frame of energy supply/demand of the whole Japan. As a result of the simulation, energy source as of 2030 is composed of coal (17%), oil (44%) and nuclear power (15%) in the case of the economic growth as viewed optimistically. Contrarily, in the case of it as viewed pesimistically, energy source is composed of coal (11%), oil (40%) and nuclear power (22%). CO2 emission is -12.4% in the case of the new energy promotion than in the standard case. 7 refs., 79 figs., 107 tabs.

  8. Process improvement technology for petrochemical plant; Sekiyu kagaku puranto ni okesu purosesu kaizen gijutsu

    Yamada, Shin

    1999-05-05

    Before, GTC technology Co. was a manufacturer of the tray as a Greenwich technology. It is the subsidiary, which undertakes technology and licence of the engineering firm in U.S.A. at present. It carries out besides the technology licence support in the startup for the prolonged driving of technical service, operating condition of the plant of improvement and optimization and, etc. Has made separation and purification technology, which made extractive distillation to be a beginning good and has the process improvement technology to the PTA (high-pure terephthalic acid) from BTX (benzene toluene xylene) of petrochemical plant. (NEDO)

  9. Survey on econometric analysis of oil substitute energy; Sekiyu daitai energy keiryo bunseki chosa

    NONE

    1996-03-01

    For the econometric analysis of petroleum substitution energy, a domestic econometric model was developed which can concretely and econometrically grasp and analyze effects of measures taken for environmental policies, energy conservation, promotion of new energy, etc. The model was made so synthetic as to catch a relationship between energy supply/demand and changes of econosocial structures in economic growth, industrial structure, life style, etc. which are extremely important elements for catching future energy demand. The model is composed of a secondary energy price model, a new energy introduction model, and an energy supply/demand model. As case parameters, selected were the price of crude oil, introduction of new energy, GDP and energy conservation, and the following cases were assumed: standard case, high price energy case, new energy introduction promotion case, low economic growth case, energy conservation case, and low energy demand case. The results of simulating each of these cases were indicated. 91 figs., 110 tabs.

  10. Metrical analysis survey of petroleum substituting energy; Sekiyu daitai energy keiryo bunseki chosa

    NONE

    1997-03-01

    The paper conducted the modeling on the economic/industrial structure giving the economic frame for energy supply/demand forecast, and made some simulations. In the simulation, assumed were a standard case, aging/hollowing case, and technical innovation case. As to macroeconomic models, macro items such as the economic growth rate, prices and IS balance were determined by giving foreign factors, financial factors, population factors, etc. In long-term energy supply/demand models, data on demand by use in commercial/residential and transportation sectors were estimated using various statistics. About the calculation result of a standard case of the former sector, the existing industries which markedly ebbed are primary products, the material system, construction/civil engineering, etc. Contrarily, the production industry such as general machines, electrical machines and automobiles increased the share. New and highly growing industries are new production industries like electronics and communication and new services like finance, insurance and communication. The GDP rate grows by 2.3% per year on average and lowers in each ten years hereafter. 53 figs., 83 tabs.

  11. Trends in business management strategies of major international oil companies; Kokusai sekiyu kigyo meja no keiei senryaku no doko

    Kashio, H. [The Institute of Energy Economics, Tokyo (Japan)

    1995-07-01

    This paper summarizes the former half part of the analysis made on business strategies of major international oil companies. The net earning of R/D Shell in fiscal 1994 increased by 1.8 billion dollars to 6.3 billion dollars. Its loan rate decreased to 16.7%. It increased the crude oil production by 3% to 2.2 million B/D, and the natural gas production by 1.2% to 7.3 billion cfd. The upstream department had the net earning decreased by 23% to 2.4 billion dollars because of decline in crude oil price. The net earning of the downstream department showed an increase by 20% over that in the previous year to 3.2 billion dollars. The chemical department had its business turned to black ink. The net earning of Exxon in the same year decreased by 200 million dollars to 5.1 billion dollars due to the reduced crude oil price and low refining margin. The upstream and downstream departments showed a decrease of 530 million and 630 million dollars respectively. The chemical department had an increase of 130% to 950 million dollars as a result of the recovery in the European markets. The net earning of Mobile in the same year showed a decrease of 2.1 billion dollars, ending in the amount of 1.1 billion dollars. The decrease has been caused by the decline in crude oil and natural gas prices and a 30% reduction in the refining margin. The chemical department changed for the better, with improved sales margins in oil products sold in overseas markets. 28 figs.

  12. Exchange of researchers of oil substituting energies in EU countries; EU shokoku no sekiyu daitai energy kenkyusha koryu jigyo

    NONE

    1996-03-01

    In order to further promote smoother introduction of oil substituting energies and development of new energies and energy saving technologies, it was intended to exchange and acquire items of information effective to learn the current state and policy trends on research and development of new energies and energy conservation in the EU countries who are the industrialized countries like Japan and enthusiastic in developing oil substituting energies. Therefore, exchange of researchers was carried out with an objective to contribute to research and development of oil substituting energies by deepening mutual understanding on the development efforts and forming efficient cooperative relationship. The researchers who visited Japan are Dr. Robert Durand (France) and Prof. and Dr. Bruno Scrosati (Italy). Dr. Durand has a great knowledge about fuel cells and storage batteries, and Dr. Scrosati about electrolytes and lithium batteries. Both gentlemen have visited the Agency of Industrial Science and Technology and the Agency of Natural Resources and Energy of the Ministry of International Trade and Industry, NEDO, Toshiba, Sony, Sanyo Electric, Japan Storage Battery, Matsushita Battery Industry, the Industrial Technology Research Institute of Osaka, and Kansai Electric Power Company. Views and information were exchanged and a number of good results were rewarded.

  13. Japan-EU joint research project on petroleum substituting energy; Nichi EU sekiyu daitai energy kanren kyodo kenkyu jigyo

    NONE

    1997-03-01

    Four EU research workers were invited from Portugal, Italy and France for promoting R & D of petroleum substituting energies in Japan. The joint research on the wide area energy use network system (advanced district cooling and heating) includes the experimental technology for measuring heat transfer acceleration and drag reduction, evaluation of rheological characteristics of fluid, and development and selection of an adequate composition equation of fluid. The joint research on MCFC includes the test method and procedure of components and cells in relation to corrosion by molten carbonate, elution of NiO cathodes, electrode modeling and alternative materials for cathodes. The joint research on geothermal gases includes the research method of fumarolic gases such as volcanic gas and geothermal gas, applications in Italian geothermal fields and the relation of geothermal gases with the origin of fluid, deep conditions and volcanic activity. In addition, the joint research on light energy conversion (energy transfer system between binuclear metal complexes) and the performance and use of metal complexes as catalyst for polymer electrolyte fuel cells was also performed. 52 refs., 20 figs., 3 tabs.

  14. Monitoring of EOR operations by electrical prospecting. 2; Denki tansaho ni yoru sekiyu kyosei kaishuho no monitoring. 2

    Ushijima, K; Mizunaga, H; Tanaka, T; Masuda, K [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Tamagawa, T [Japex Jeoscience Institute, Tokyo (Japan)

    1996-10-01

    Fluid flow tomography (FFT) was applied to monitor the behavior of underground fluid in steam enhanced oil recovery (EOR) for oil sand reservoirs. FFT uses electrode arrangement of a mise-a-la-masse method, and continuously measures time variation in charged and spontaneous potential at various surface points to obtain realtime the images of underground seepage flow. It continuously measures ground surface potentials of 120 channels at intervals of 2s by applying alternative DC between a casing pipe and distant current electrode. It separates charged and spontaneous potential components, and converts them into time series data. It estimates the time and spacial distributions of seepage flow from time variation in spontaneous potential. It determines the change rate distribution of time-sliced apparent resistivity from charged potential to estimate the scale and area of seepage flow. As the experimental result, positive and negative electrodes in the change rate distribution were observed, and the direction connecting each electrode agreed with that of resistivity anomaly. FFT could observe realtime time variation in apparent resistivity due to steam injection. 9 refs., 7 figs.

  15. Fiscal 1999 research report. Simulation analysis on petroleum substituting energy; 1999 nendo sekiyu daitai energy keiryo bunseki chosa hokokusho

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on simulation analysis on petroleum substituting energy. The simulation model for analyzing social and energy supply and demand structures comprehensively was established by improving the China and Korea models developed in fiscal 1998 through a use of input-output tables. In simulation of the China model, the reference case showed that a primary energy demand in 2030 reaches 3.3 times as much as that in 1997 (2.9 times in CO{sub 2}), resulting in serious energy and environment problems. Reduction of primary energy and CO{sub 2} is possible by promotion of energy saving and introduction of a carbon tax. In simulation of the Korea model, the reference case showed that CO{sub 2} emission in 2030 reaches 2.2 times as much as that in 1997, showing an annual increase rate of 2.4%. The annual increase rate can be reduced by introducing a carbon tax. The simulation model for automobile energy was also established for major countries in Asia. Automobile energy consumption increases with diffusion of automobiles until 2030 gradually. In particular, the consumption in China reaches that in Japan in 2010. (NEDO)

  16. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  17. FY 1998 survey report. Petroleum substituting energy metering analysis survey; 1998 nendo chosa hokokusho. Sekiyu daitai energy keiryo bunseki chosa

    NONE

    1999-03-01

    In this survey, metering models in the Asian/Pacific region where energy demand is rapidly increasing were constructed which are used for the comprehensive analysis of the relations between changes in social structure such as economic growth, change in industrial structure, and progress in energy conservation technology and new energy technology, and the energy supply/demand structure. The survey was carried out aiming at contributing to the international development of Japan's energy policy in future by quantitatively analyzing/evaluating influences of various energy policies/economic policies on the economy and energy supply/demand, through various kinds of simulation models. In FY 1998, information collection for modeling was made in China and Korea out of the Asian/Pacific region. At the same time, pilot models were constructed, and simulation was made for the standard case. Moreover, an analysis was conducted of the relation between economic growth and motorization in each country of the world as the basic data preparation on energy consumption in the transportation sector. (NEDO)

  18. Investigation of the deposit formation in pipelines connecting liquefaction reactors; 1t/d PSU ni okeru ekika hanno tokan fuchakubutsu no seisei yoin ni kansuru ichikosatsu

    Okada, Y.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    The liquefaction reaction system of an NEDOL process coal liquefaction 1t/d PSU was opened and checked to investigate the cause of the rise of differential pressure between liquefaction reactors of the PSU. The liquefaction test at a coal concentration of 50 wt% using Tanito Harum coal was conducted, and it was found that the differential pressure between reactors was on the increase. By the two-phase flow pressure loss method, deposition thickness of deposit in pipelines was estimated at 4.4mm at the time of end operation, which agreed with a measuring value obtained from a {gamma} ray. The rise of differential pressure was caused by deposit formation in pipelines connecting reactors. The main component of the deposit is calcite (CaCO3 60-70%) and is the same as the usual one. It is also the same type as the deposit on the reactor wall. Ca in coal ash is concerned with this. To withdraw solid matters deposited in the reactor, there are installed pipelines for the withdrawal at the reactor bottom. The solid matters are regularly purged by reverse gas for prevention of clogging. As the frequency of purge increases, the deposit at the reactor bottom decreases, but the deposit attaches strongly to pipelines connecting reactors. It is presumed that this deposit is what Ca to be discharged out of the system as a form of deposition solid matter naturally in the Ca balance precipitated as calcite in the pipeline connecting the reactor. 3 refs., 5 figs., 4 tabs.

  19. Design of hydroprocessing catalyst for the production of ultra clean fuels. Super clean nenryo wo mezashita jushitsu tanka suiso seisei shokubai no kokinoka

    Shimada, Hiromichi (National Chemical Lab. for Industry,Tsukuba, (Japan))

    1990-02-01

    In order to develop high function catalyst for the ultra clean fuel refining and other purposes, the catalyst was studied in correlation between the function and structure. Hydrogenation power of aromatic ring and hydrogenolysis power of carbon-carbon bonding, which are principal functions of catalyst in the hydrogenation refining, were evaluated with model material. 30 kinds of catalyst were figure shown in classification result of evaluation. As for the mutual operation of molybdenum and carrier, it is necessary for molybdenum sulfide to be highly dispersed on carrier in order to heighten the hydrogenation activity. While the hydrogenolysis activity, as necessitating electrically negative molybdenum type to be formed on carrier, is manifested by the formation of Bronsted acidity point with hydrogen sulfide, adhering thereto. As for the molybdenum sulfide catalyst, mainly hydrogenation activity point, in case that structure, similar to molybdenum disulfide, is dispersed as a single layer on carrier, and hydrogenolysis activity point, in case that it forms a multi-layer structure thereon, are formed in edge part of respective crystal. The lowering in activity under a long time sevre condition, which mainly are carbonic material deposition, matallic adhesion, etc., is also influenced by the structural change in catalyst. 10 refs., 5 figs. 2 tabs.

  20. Formation of secondary products in water purification. ; Charactarization of chlorination by-products. Josui shori ni okeru fukuseiseibutsu. ; Enso shori ni yoru shodoku fukuseiseibutsu no seisei tokusei

    Aizawa, T [The Inst. of Public Health, Tokyo (Japan)

    1993-12-10

    Chlorination of drinking water is an inevitable process for the purification of drinking water. It has been made clear that injected free chlorine reacts with organic matter in water to produce chlorinated by-products. Many of those compounds are toxic, and studies have been made on the international water quality standard. Water quality standard has been revised also in Japan. The sources of organic matter which is the cause for production of chlorinated by-products vary according to the kinds and conditions of the water source for drinking water. Removal of precursors in the original water, removal of by-products, and change in the disinfection system with alternate disinfectant for chlorine are among the measures for decreasing chlorinated by-products at water purification plants, but the first one is employed as the basis method. It is expected that more severe regulation may be imposed on the quality of the water source for drinking water, and more strict oxidation and disinfection systems is inevitable for water management based on the new water quality standard. 10 refs., 5 figs., 2 tabs.

  1. Report on the separation and refining technology sub-committee meetings in fiscal 1987; 1987 nendo bunri seisei gijutsu bukai hokokusho

    NONE

    1988-03-01

    The separation and refining technology sub-committee has held two meetings in this fiscal year. The first sub-committee meeting (October 9, 1987) was held for the major agenda of the research and development of the basic studies; as the summary of the achievements in fiscal 1986, the up-grading by fractions and of the total fraction collectively, up-grading of kerosene and light oil fractions, up-grading of medium to heavy fractions; and as the study plans for fiscal 1987, the up-grading of coal liquefied oil, a technology to separate hetero compounds, development of their applications, and the reports and deliberations thereon. The major agenda of the second sub-committee meeting (February 10, 1988) were the interim report on the achievements in research of up-grading the coal liquefied oil in fiscal 1987, the interim reports on research achievements in the technology to separate hetero compounds and development of its applications, and the reports and deliberations thereon. The conventional up-grading sub-committee was dissolved in fiscal 1987 to form a new organization, whereas the 'separation and refining sub-committee' was founded newly. With respect to the up-grading matters, reports were given on the achievements thereon as a result of using a micro reaction device and a bench reaction device as in the past, and on the achievements in the application development. In addition, on the hetero related matters, directionality of the survey and the result therefrom were reported. (NEDO)

  2. System approach on solar hydrogen generation and the gas utilization; Taiyo energy ni yoru suiso no seisei oyobi sono riyo system ni kansuru kenkyu

    Fujii, I; Hirooka, N; Deguchi, Y; Narita, D [Meiji University, Tokyo (Japan)

    1997-11-25

    An apparatus is developed to establish a system which allows utilization of hydrogen safely and easily, and its applicability to a hydrogen system for domestic purposes is tested. The system converts solar energy by the photovoltaic cell unit into power, which is used to generate hydrogen by electrolysis of water at the hydrogen generator, stores hydrogen in a metal hydride , and sends stored hydrogen to the burner and fuel cell units. It is found that a hydrogen occluding alloy of LaNi4.8Al0.2 stores hydrogen to approximately 80% when cooled to 20 to 25degC, and releases it to 10% when heated to 40degC. The fuel cell uses a solid polymer as the electrolyte. The hydrogen gas burner is a catalytic combustion burner with a Pt catalyst carried by expanded Ni-Al alloy. The optimum distance between the burner and object to be heated is 22mm. High safety and fabrication simplicity are confirmed for use for domestic purposes. The system characteristics will be further investigated. 4 refs., 8 figs.

  3. Evaluation report on the design of solid catalysts for saving energy in petrochemical industry; Sekiyu kagaku no tame no sho energy gata kotai shokubai sekkei hyoka hokokusho

    NONE

    2001-03-01

    The aim is to improve on hydrocarbon oxidation which is a difficult reaction (analogous to combustion and having potential for heat generation or explosion, with restrictions therefore imposed on reaction conditions) by use of a catalyst supporting porous membrane. The fiscal 1999-2000 results are stated. In this effort, the target reaction is promoted by a catalyst supported by a porous membrane while combustion is controlled by the said porous membrane that separates oxygen and hydrocarbon from each other. Such a design was not available since a catalyst supporting inorganic membrane withstanding so high a temperature was difficult to prepare. Recently, however, a porous membrane with its pores regulated to microstructural dimensions was developed. The activity of a Pd membrane catalyst is evaluated in view of the degree of oxidation of propylene, cyclohexene, and benzene. It is then found that hydrogen that has passed the Pd membrane participates in the reaction. In a propylene oxidation test using a membrane type Ag/Al{sub 2}O{sub 3} catalyst, it is found that acetone is generated and that oxygen after passing through the membrane participates in the reaction. Methods are studied for preparing a metal membrane in which the catalyst system comprises a catalyst supporting porous membrane and a Pd membrane. In the fabrication of metal membranes, a highly selective hydrogen permeable membrane is stably prepared by the thermal CVD (chemical vapor deposition) method. (NEDO)

  4. MT survey in the Minaminoshiro oil field; Minaminoshiro chiiki ni okeru MT ho ni yoru sekiyu tanko (sanjigen MT ho chosa no kento). 1

    Matsuo, K; Minegishi, M [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-10-22

    Preliminary experiment, investigation, and study are conducted prior to an experimental 3-D MT (magnetotelluric) survey planned to be carried out in the Minaminoshiro district, Akita Prefecture. In the preliminary investigation, MT measurements were performed at nine locations. It was anticipated that national highways, waste treatment plants, high-voltage power lines, and railways in presence in the district would act as noise sources. Although the impact of such noise was detected in the single site treatment result, yet it was found that it would be mostly eliminated by use of the remote reference treatment. It was learned that the resistivity structure in this district was quite low in contrast or 1 ohm/m against 30 ohm/m, but the result of 3-D model calculation indicated that a sufficient analysis would be possible even in such a low contrast case. Furthermore, as the result of the study of the density of observation stations in the magnetic field, it was found that changes in the response of magnetic field to the resistivity structure would be approximately 2% at the maximum and that the ill effect on the result of measurement would be of the negligible magnitude even when a single magnetic field observation station is deployed against plural electric field observation stations. 6 refs., 7 figs.

  5. Simulation study using 3-D wavefield modeling for oil and gas exploration; Sanjigen hadoba modeling wo mochiita sekiyu tanko no simulation study

    Sato, T; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan); Saeki, T [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    As the surroundings of objects of oil exploration grow more complicated, seismic survey methods have turned 3-dimensional and, in this report, several models are examined using the 3-dimensional simulation technology. The result obtained by the conventional wave tracking method is different from actual wavefields, and is unrealistic. The difference method among the fullwave modelling methods demands an exorbitantly long computation time and high cost. A pseudospectral method has been developed which is superior to the difference method, and has been put to practical use thanks to the advent of parallel computers. It is found that a 3-dimensional survey is mandatory in describing faults. After examining the SEG/EAGE Salt model, it is learned that the salt is well-developed and that 3-dimensional depth migration is required for sub-salt exploration. It is also found through simulation of the EAGE/S Overthrust model, which is an elastic model, that no quality records are available on thrust zones in complicated terrains. The records are poor in quality since the actually measured wavefield is regarded as an acoustic wavefield when it is an elastic wavefield. 1 refs., 18 figs., 2 tabs.

  6. Actual situation and future tendency of relaxation of petroleum restrictions in Western Europe. Seio ni okeru sekiyu kisei kanwa no jittai to kongo no doko

    1989-07-31

    An oversea investigation was made in 1988 to study the present situation of the relaxation trends of petroleum resrictions in the countries of Western Europe. Among petroleum markets of West European countries, in those of West Germany and UK both quantity and price have had no restrictions. And in France they were liberalized quite recently. On the other hand, in South European countries such as Italy, Spain and Greece the prices of petroleum products are controlled by the governments. EC is going to integrate petroleum markets by the end of 1992 so that petroleum products may flow beyond the borders freely. In France, relaxation of restrictions on the petroleum industry was carried out in 1985 employing the petroleum business law of 1928 with elasticity and four years have passed since then. In Italy petroleum companies cannot decide the prices of major petroleum products freely. In Spain, the petroleum market is going to be completely liberalized in 1993 in accordance with the engagement with EC. Greece is at strife with EC on the adjustment of policies. 26 figs., 86 tabs.

  7. Fiscal 1999 basic survey report for promotion of joint implementation. Energy saving at petrochemical plant; 1999 nendo sekiyu kagaku kojo no sho energy chosa hokokusho

    NONE

    2000-03-01

    A survey is conducted of energy-saving and greenhouse gas reducing measures in cooperation with the National Petrochemical Public Company Limited (NPC), Thailand. The NPC is the first petrochemical producer in that country and, after 10 years' operation, the largest such producer there. Transfer of energy-saving technologies from Japan will lead to the construction of clean development mechanism (CDM) in the future. The NPC plant surveyed is situated in a Maptaphut industrial complex, and produces ethylene propylene from natural gas and at the same time serves as a utility center to supply electricity and steam to factories and plants in the vicinity. Items examined involve waste heat power generation, power generating gas turbine efficiency improvement, ethylene plant cracking furnace heat retaining capability enhancement, steam pipe heat retaining material renewal, and replacement of obsolete air conditioners with higher-efficiency equipment. After tentative calculation a conclusion is reached that the total of energy-saving effects of the said five items will be 21,900 tons/year in terms of crude oil and that a CO2 reduction will be feasible at a rate of 45,300 tons/year. These figures are larger than the ones predicted before the survey. A total of 354.3 million bahts will have to be invested. Negotiations will continue with attention directed to the progress of NPC's preparedness to accept CDM. (NEDO)

  8. FY 2000 report on the measuring/analytical survey of petroleum substituting energy; 2000 nendo sekiyu daitai energy keiryo bunseki chosa hokokusho

    NONE

    2001-03-01

    Looking for effective policy on petroleum substituting energy, measuring models were made for analyzing relations between changes in social structure and energy supply/demand structure. Through the simulation using these models, effects of difference in energy policy on economy and energy supply/demand were studied. Countries for survey were Thailand, the Philippines, Indonesia, Malaysia, China and Korea. The measuring model is composed of the macroeconomic model and the energy supply/demand model. In the case of Korea, the interindustry-relations model was added. Using the macroeconomic model, asked were fluctuations in various economic activities/industrial structure/price/trade balance such as GDP and crude steel production by inputting overseas indices, population indices and financial indices such as the world trade, crude oil price and exchange rates. In FY 2000, for ASEAN countries, data were collected for analysis of relations between changes in economical/social structure and energy supply/demand structure. Using the pilot model constructed, the simulation was made on the standard case. (NEDO)

  9. Basic tests of a rotation seismograph; Kaiten jishinkei no kaihatsu

    Matsubayashi, H; Kawamura, S; Watanabe, F; Hirai, Y; Kasahara, K [Nippon Geophysical Prospecting Co. Ltd., Tokyo (Japan)

    1996-05-01

    For the purpose of developing a rotational seismograph capable of measuring the rotational component of seismic waves, vibratory gyroscopes were installed in the ground for the measurement of vibration of the ground, and the measurements were compared with the values obtained from tests using conventional velocity type seismographs. In the experiment, the plank was hammered on the east side and west side. The seismographs were arranged in two ways: one wherein they were installed at 7 spots at intervals of 1m toward the south beginning at a position 3m south of the vibration source with their rotation axes oriented vertical, with velocity type seismographs provided at the same spots; and the other wherein three rotational seismographs were installed 3m south of the vibration source with their rotation axes respectively oriented vertical, in the direction of N-S, and in the direction of E-W, with a velocity type seismograph provided at the same spot. It was found as the result that the rotational seismograph has a flat band on the lower frequency side and that it may be applied to elastic wave observation across a wide band. Accordingly, it is expected that it will be applied to exploration that uses the SH wave, to structural assessment that uses the Love wave, and to collecting knowledge about the features of natural earthquakes. 2 refs., 8 figs.

  10. Development of aluminium pleasure boats; Arumisei pleasure boat no kaihatsu

    Tsuzuki, A. [Toyota Motor Corp., Aichi (Japan)

    1999-10-01

    In February 1997, Toyota entered the marine business, a new business sector for it, by marketing a 28-foot cabin cruiser PONAM-28, developed by utilizing its automotive technologies. When Toyota began studying the possibility of entering the marine vessel industry in 1990, its main focus was on the environment. Therefore, in terms of materials procurement for the designs, Toyota refrained from using thermosetting resins, as much as possible. Instead, the decision was made to use an easily recyclable aluminum alloy for the hull which amounts to one-fourth of the vessel's total weight. (author)

  11. Development of artificial soft rock. Jinko nangan zairyo no kaihatsu

    Kishi, K.; Nishioka, T. (The Tokyo Electric Power Co. Inc., Tokyo (Japan)); Nojiri, Y.; Kurihara, H.; Fukazawa, E. (Kajima Corp., Tokyo (Japan))

    1990-09-15

    When a part of the ground is replaced with artificial materials in the construction of important structures on soft rock foundations, it is desirable for the artificial materials to have the rigidity equivalent to that of the surrounding ground and to be stable in the long term. The article reports a success in the development and utilization of artificial soft rocks satisfying the above conditions by using a raw material produced locally at the construction site. The soft rock aimed at was mudstone belonging to the Neocene period, and the artificial material of soil-mortal system is selected as the equivalent having the same physical properties. Improvements in selection of solidification agents and cohesive soil were especially contrived: taht is, a new material for solidification was developed by mixing blast-furnace cement and gypsum; and the mudstone on the site was used as the cohesive soil by slurrying it to adjust its grain size to homogeneous composition. The artificial soft rock resulting from the above contrivance showed excellent flow, self-leveling, and filling properties at the stage of fresh mortar, and the physical properties after hardning was very similar to those of the natural ground. The long-term stability was also confirmed by the tests on hydration reaction and environmental factors. 2 figs., 1 tab.

  12. Development of field navigation system; Field navigation system no kaihatsu

    Ibara, S; Minode, M; Nishioka, K [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1995-04-20

    This paper describes the following matters on a field navigation system developed for the purpose of covering a field of several kilometer square. This system consists of a center system and a vehicle system, and the center system comprises a map information computer and a communication data controlling computer; since the accuracy for a vehicle position detected by a GPS is not sufficient, an attempt of increasing the accuracy of vehicle position detection is made by means of a hybrid system; the hybrid system uses a satellite navigation method of differential system in which the error components in the GPS are transmitted from the center, and also uses a self-contained navigation method which performs an auxiliary function when the accuracy in the GPS has dropped; corrected GPS values, emergency messages to all of the vehicles and data of each vehicle position are communicated by wireless transmission in two ways between the center and vehicles; and accommodation of the map data adopted a system that can respond quickly to any change in roads and facilities. 3 refs., 13 figs., 1 tab.

  13. Development of new catalytic materials; Shinshokubai zairyo no kaihatsu doko

    Tatsumi, Takashi [Yokohama National Univ., Kanagawa (Japan)

    1999-04-05

    The catalyst fulfils large role for the solution of environmental problem, resources problem, and energy problem. It is popular to carry out the research, which intends to realize the new process of which the environmental loading is low by the new catalyst. And, the development of catalyst material, which demonstrates the function under the ultimate condition like the environmental catalyst, is required. The interest has leaned in also using the solid catalyst for the synthesis of fine chemical such as intermediate and perfume of the medical supply synthesis. In this paper, the following are described as a new catalyst material: Zeolite and development trend of meso porous molecular sieve explosively studied recently. The application to the reaction is also simply touched. (NEDO)

  14. Development of mechanical brake assist; Mechanical brake assist no kaihatsu

    Konishi, M; Shingyoji, S; Nakamura, I; Tagawa, T; Saito, Y; Ishihara, T; Kobayashi, S; Yoshida, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    We have recognized that there are drivers who cannot apply strong brake pedal force , in spite of the necessity of hard braking in emergencies. We have developed a `mechanical brake assist system` which assists drivers appropriately, according to the drivers` characteristics based on studying the characteristic`s of conditions of drivers applying the brake pedal force in emergency conditions. 2 refs., 7 figs., 1 tab.

  15. Developments of space station; Uchu station no kaihatsu

    Hashimoto, H. [National Space Development Agency of Japan, Tokyo (Japan)

    1996-03-05

    This paper introduces the Japanese experiment module (JEM) in developing a space station. The JEM consists of systems of a pressurizing section, an exposure section, a pressurizing portion of a supply section, a manipulator and an exposure portion of the supply section. The pressurizing section circulates and controls air so that crews can perform experiments under pressurized environment. The exposure section is a part in which experiments are carried out under exposure environment. The supply section runs between a station and the ground, with required devices loaded on it. The manipulator performs attaching a payload for the exposure section and replaces experimental samples. The JEM undergoes a schedule of fabricating an engineering model, testing for a certification a prototype flight model, and putting the model on a flight. The pressurizing section, exposure section and manipulator are at the stage of system tests. Surveillance of the JEM and control of the experiments are carried out at the Tsukuba Space Center. The Center is composed of a space experiment building, a zero-gravity environment testing building, an astronaut training building, a space station operating building, and a space station testing building. 7 figs., 2 tabs.

  16. Fiscal 1975 Sunshine Project research report. Research on hydrogen purification storage transport systems, and their safety technologies; 1975 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho

    NONE

    1976-05-31

    In fiscal 1975, research was made on (1) some problems and their solutions for practical hydrogen purification storage transport (HPST) systems, and (2) analysis and optimization of HPST systems. The material-energy flow diagram and rough hydrogen system relevance tree were prepared, and the position of HPST system in hydrogen systems was considered together with use of liquid hydrogen. In (1), the current technologies and problems were arranged for every component of purification system, storage system, transport and distribution system, and metal hydride. Study was also made on some problems and solutions for their R and D. In (2), study was made on the basic model of HPST, and the compatibility with a total energy system. Overseas and Industrial Research Institute (IRI)'s trial calculation results were arranged for HPST cost data as input data for trial calculation of optimization. As for a safety and reliability, study was made on the target, system and main R and D fields for the safety management of HPST system, referring to the concept of safety managements in nuclear power generation and LNG system. (NEDO)

  17. Studies of initial stage in coal liquefaction. 4. Radical formation and structural change with thermal decomposition of coal; Ekika hanno no shoki katei ni kansuru kenkyu. 4. Netsubunkai ni tomonau radical seisei kyodo to kozo henka

    Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan); Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In relation to coal liquefaction reaction, the effect of the coexistence of transferable hydrogen (TH) from process solvent on reduction of radical concentration and the effect of pre-heat treatment on average structure of coals were studied. In experiment, change in radical concentration with temperature rise was measured using the system composed of Yallourn coal and process solvent. The results are as follows. Process solvent with a wide boiling point range of 180-420{degree}C is effective in suppressing an increase in radical concentration even at higher temperature. The effect of hydrogen-donating solvent increases with TH. It was also suggested that high-boiling point constituents in solvent stabilize radicals even over 400{degree}C by vapor phase hydrogenation. The experimental results of pre-heat treatment are as follows. Although the conversion improvement effect of TH is equivalent to that of the model solvent, TH tends to produce soluble products with smaller ring numbers. It was thus suggested that pre-heat treatment in process solvent is effective to inhibit retrogressive reactions. 6 refs., 5 figs., 1 tab.

  18. BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

    Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

    1996-10-28

    On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

  19. Achievement report for fiscal 1976 on Sunshine Program. Research on systems for hydrogen refining, transporting, and storing, and technology for assuring safety; 1976 nendo suiso no seisei yuso chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho

    NONE

    1977-03-01

    The results of studies conducted in the 3-year period beginning in fiscal 1974 are collected in this report. Dealt with in Chapter 1 are hydrogen production systems that constitute the stages before and after a hydrogen refining/transporting/storing subsystem, the future outlook of a hydrogen supply system with consideration bestowed on its connection with hydrogen-using systems, and how subsystems involving transportation and storage should be in such a hydrogen supply system. In Chapter 2, for the purpose of helping the construction in the future of a total energy system for hydrogen, the flows of energy and substances in Japan based on the records of fiscal 1974 and charts of the actualities of hydrogen utilization are shown. In Chapter 3, tentative designs of hydrogen supply systems are taken up for assessment. In Chapter 5, subsystems for a hydrogen supply system including topological patterns are tentatively designed. In Chapter 6, the transportation and storage of hydrogen are quantitatively evaluated, and assessment is conducted about investment for the embodiment of a topological model, selection of a profitable system, and environmental safety. Reference is also made in this chapter to research and development policies under which a hydrogen system to be the target is manifestly defined, where the aim of such research and development is declared and the need of its achievement is emphasized. (NEDO)

  20. Preparation of ultrafine iron particles by chemical vapor deposition of Fe(CO) sub 5. Fe(CO) sub 5 wo gebryo to suru kiso kagaku hanno ni yoru tetsuchobiryushi no seisei

    Sawada, Y; Kageyama, Y. (Mitsubishi Petrochemical Co. Ltd., Tokyo (Japan)): Iwata, M. (Nagoya University, Nagoya (Japan). Faculty of Engineering)

    1991-11-10

    An ultrafine iron particle preparing process was developed, which wses gaseous phase pyrolysis in magnetic field of iron pentacarbonyl, Fe(CO){sub 5}, based on the fact that Fe(CO){sub 5} has peculiar characters that its boiling point is as low as 103{degree}C, and starts decomposing in a low temperature zone of 100{degree}C or lower. Vaporizing and introducing into a reactor an fe(CO){sub 5}, andPyrolyzing it at 200-600{degree}C while being diluted with nitrogen and applied with a magnetic field produced uitrafine iron particles of a necklace-like chain comprisinh primary particles having diameter of 15 to 25 nm with 10 to 40 of them linked in a straight chain. It was found that the specific surface area is 30-50 m{sup 2}/g, with the diameter converted from the specific surface area being relatively close to the average diameter obtained from TEM photograph, and that the particle has few pores. Magnetically the iron powder has a coercivity of 123-131 KA/m and a specific saturation magnetization of 120-140 Am{sup 2}/kg, and is expected to be applied as a high density magnetic recording medium. 5 refs.,8 figs., 3 tabs.

  1. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology; 1974 nendo suiso no seisei yuso chozo system oyobi hoan gijjutsu ni kansuru kenkyu seika hokokusho

    NONE

    1975-05-31

    This study aims at the following. As to an alternative plan of the hydrogen distribution system, this paper makes the comprehensive evaluation from viewpoints of possibility, adaptability to society, economical efficiency, reliability, dynamic characteristics, etc., selects the most rational system and picked up the problems for realization of the system. It also sets up standards for safety technology relating to the hydrogen energy system and acquires the basic knowledge/information on concrete disaster prevention technology which backs up the standards. Among those, in this fiscal year, as system analysis of the hydrogen distribution system, study was made on system analysis of the system alternative plan and problems on system realization. Next, as an investigational study on safety technology in hydrogen energy system, the paper conducted the survey/collection in Japan and abroad of the present law, standards for handling, and examples of disaster/accident in relation to hydrogen, and the survey research on the concrete safety problem predicted. The paper studied the technology related to the safety problem required for safety (survey of effects of impurities, measuring technology, technology to prevent leakage accidents, etc. ). (NEDO)

  2. Separation and purification of lactic acid. Thermal catalytic depolymerization of poly-lactic acid into lactide; Hakkoho nyusan no bunri seisei ni kansuru kenkyu. Pori nyusan no rakuchido eno sesshokuteki netsukai jugo

    Morita, M.; Hirama, Y.; Liew, M. [Hokkaido National Industrial Research Institute, Sapporo (Japan)

    1996-05-10

    A new separation and purification method for lactic acid from fermentation broth is proposed by which poly-lactic acid produced from unpurified lactic acid is catalytically depolymerized into lactide fractions then further purified into lactide. In the present study, thermal depolymerization catalysts were investigated for commercial use. Iron catalysts, especially metallic iron, and ferrous oxide and lactate, were found to provide almost the same catalytic activity and lactide composition in depolymerization products and those in tin octoate and antimony oxide catalysts. Ferrous oxide was also applied to depolymerize poly-lactic acid derived form unpurified lactic acid to compare catalytic activity and lactide composition and was confirmed to show results similar to those of pure polymer. Based on these findings, it is concluded that iron catalysts can be used commercially. Furthermore, catalytic depolymerization of poly-lactic acids with different molecular weights were studied. Polymers with Mw 5,000-10,000 were found to be better for production of lactide, based on the behavior of depolymerization and lactide content in the product. 5 refs., 9 figs., 1 tab.

  3. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Investigational study of the measuring control system for safety in the stage of low temperature storage and refining of hydrogen); 1974 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru chosa kenkyu

    NONE

    1975-05-30

    Safety technology is necessary and indispensable for future materialization of a hydrogen energy system. The survey was made from a viewpoint of safety technology in refining hydrogen at low temperature and in storing it in a low temperature liquid state. Japan has so far had no experiences for the handling and consumption of liquid hydrogen except the partial use at laboratory. Accordingly, collected here was literature on the storage, transportation, handling, low temperature refining of the liquid, etc. The present state of technology in Japan and abroad was grasped and items in the safety relation were picked up. As to the existing literature on the hydrogen relation, there is much literature on the U.S. NASA project, and there is also much on practical business details such as the handling of a large quantity of liquid. Therefore, from each literature mostly on the above, the literature on the liquid storage, transportation use storage tank and refining method was reviewed and arranged, and at the same time, the items were picked up of the safe disposal method, disaster prevention relation, and measuring relation. The paper also arranged the results of surveying hydrogen physical properties and equipment materials which are closely related to safety general, in particular, and examples of disaster. (NEDO)

  4. Achievement report on research and development in the Sunshine Project in fiscal 1976. Researches related to hydrogen refining, transporting and storing systems, and safety assurance technologies (Surveys and researches on low-temperature storage of hydrogen, and measurement and control systems for safety in refining stage); 1976 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru chosa kenkyu

    NONE

    1977-03-01

    This paper discusses low-temperature storage of hydrogen, and safety in the refining stage thereof. Discussions were given on a device to discharge safely hydrogen evaporated from a liquefied hydrogen storing tank rolly. A testing equipment of a 1/10 size of a full size equipment was fabricated on a trial basis. The equipment was used to test discharging a gaseous mixture containing hydrogen at concentration of about 2%, while air is being supplied from a blower directly connected to a gas motor (rotating on gas pressure) with treatment rate of 15 Nm{sup 3}/h. In order to keep the hydrogen concentration below the lower explosion limit of 4%, uniformity in the spatial distribution of the concentration is important. Full consideration should be given thereto in future designing works. With a cryogenic adsorption refining device for hydrogen, oxygen content is adsorbed, and hydrogen is refined. During regeneration of the adsorption device, oxygen is discharged. Experiments on regeneration methods were performed for comparing and discussing oxygen discharge behavior by using three systems: nitrogen purge, hydrogen purge, and temperature raising. Cases were found in which oxygen concentration in the exhaust gas exceeds the lower explosion limit of 4%. There is a number of important assignments to assure safety, including specific measures to prevent the above excess, reciprocal influence of multiple impurities, and removal of ignition sources. The present experiments have great significance in providing fundamental items of information. (NEDO)

  5. Fiscal 1975 Sunshine Project research report. Research on refining, transport and storage systems for hydrogen, and their safety technologies (Research on measurement/control system for safety management in low-temperature storage and refining processes of hydrogen); 1975 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru kenkyu chosa

    NONE

    1976-05-28

    The following were selected as themes necessary and important for the safety of the forthcoming hydrogen energy system, based on the fiscal 1974 document survey result, and the fiscal 1975 research results. First as for low- temperature storage of hydrogen, since safe discharge of hydrogen gas generated in a storage tank is important, gas motor discharging usually used for such transport tanks as tank lorry, and burn bond discharging suitable for discharge of a large amount of hydrogen were selected as test items. Next as for storage and transport of low-temperature hydrogen such as liquid hydrogen, a low-temperature control valve to control the amount of liquid hydrogen for transport was selected as a test item. Under the assumption of the model tests on the above 3 items in fiscal 1976, various studies and trial designs were made on concrete test equipment. The test plans were also prepared for some ones among them. (NEDO)

  6. Amendment of oil related systems. Abolishment of the temporary measure law for importing specific petroleum products and amendment of the oil storage law and the volatile oil selling business law; Sekiyu kanren no seido kaisei ni tsuite. Tokutei sekiyu seihin yunyu oyobi kihatsuyu hanbaigyoho no kaisei

    Kobayashi, I. [Small and Medium Enterprise Agency, Tokyo (Japan)

    1995-07-20

    This paper describes the following matters related to amendment of oil related systems which will be enforced according to the result of discussions at the Petroleum Council on the ways the oil product supply should be in the future. The temporary measure law for importing specific oil products shall be abolished when it will be expired in March 1996. This is because the law has limited the oil product importing organizations only to oil companies who have oil refining capabilities, and the continuation of the law would lose its justifiability under the present circumstances in the petroleum industry. The oil reservation law is then amended so that the emergency handling ability on oil supply will not be hampered even after possible expansion in the number of oil product importing organizations as a result of the abolishment of the temporary measure law. The quality management systems for oil products will also be revised so that the present level on quality items of the minimum necessity will not be declined with respect to the environments and safety. Furthermore, the area designating system that has been limiting erection of oil service stations will be repealed by October 1996. 2 tabs.

  7. Exploration for petroleum and natural gas in Sonai Plain

    Konishi, K

    1965-09-01

    Exploration in the Sonai Plain by Sekyu Shigen Kaihatsu Kabushiki Kaisha (Oil Resources Development Corporation) since 1955 is described. The development tasks are made difficult due to the presence of permeability traps. However, 41 out of 65 wells drilled up to late March of 1965 have been successful. Quantities of crude oil and natural gas produced in 1963 were, respectively, 5 and 6 times those of 1958. The Sonai Plain is a relatively new area, and there are still many unknown factors, yet the rate of development has increased greatly. More and deeper wells are expected to be drilled with even better results.

  8. Fiscal 1995 report on the survey of making models for introducing petroleum substituting energy systems. 2; 1995 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 2

    NONE

    1996-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with features of the buildings and courses for how to construct infrastructures of towns or cities in case of development, redevelopment, etc. In fiscal 1995, each of the petroleum substituting energy systems was studied more detailedly, and the trend of building facilities for the introduction was studied and arranged. Energy systems by the following were set up paying attention to energy sources, energy conversion and energy transportation as factors composing a petroleum substituting energy system: photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of temperature difference energy, cogeneration, load levelling, wide-area energy supply, etc. Also studied and arranged were energy demand, location, the recent trend, the point of introduction of energy systems, examples of introduction, etc. in relation to indoor sport facilities, hospitals, hotels, multiple dwelling apartments, commercial facilities, offices, plants, etc. 52 figs., 55 tabs.

  9. Report on surveys in fiscal 1998 on the project to invite petroleum substituting energy related experts in Japan and EU; Nichi EU sekiyu daitai energy kanren senmonka shohei jigyo 1998 nendo chosa hokokusho

    NONE

    1999-03-01

    In relation with coping with global environmental problems in recent years, needs are increasing more than ever for enhancing fossil energy utilization rates, developing and expanding utilization of petroleum substituting energies that can substitute fossil energies. Since Japan is particularly a large energy consuming country, and cannot escape from depending on import for the majority of its energy resources, it is an urgent issue to enhance the energy utilization efficiency and further promote development and utilization of new energies. To do this, it is indispensable to exchange such item of information as identification of actual status in other countries of handling the petroleum substituting energies. Taking up geothermal energy, fiscal 1998 invited four experts from EU countries. Visits were made for about two weeks on Japanese research institutes and business enterprises related to geothermal energy, and opinions and information were exchanged. A seminar was held on the final day, where the EU experts have made presentations on the current status and future prospects on geothermal research and development in EU. Greatly valuable suggestions were given for the Japan's future geothermal research and development. (NEDO)

  10. Time domain electromagnetic method for petroleum exploration. Part 3. Case study in Yoneyama area; Sekiyu tansa ni okeru TDEM ho data shutoku to kaiseki ni tsuite. 3. Niigataken Yoneyama chiiki deno tekiyorei

    Ishikawa, H; Mitsuhata, Y [Japan National Oil Corp., Tokyo (Japan); Shiga, N [Mitsui Mineral Development Engineering Co. Ltd., Tokyo (Japan)

    1996-05-01

    The result is reported of a TDEM method-based survey for oil exploration conducted in the Yoneyama district, Niigata Prefecture. The survey covered the southern part of the sedimentary basin in the prefecture, known for the poor quality of the seismic prospecting data that had been recorded. The purpose of the TDEM method-assisted survey was to probe the high-resistivity volcanic rock structure and low-resistivity sedimentary layer, and to know their details. The obtained data were subjected to interpretation by use of the 1D inversion method. A 4000m-deep level was subjected to interpretation, 34 data were inputted, and the early model consisted of 20 layers. As the result, it was found that there was a high-resistivity layer ranging from the ground surface down to a depth of approximately 500m, that a low-resistivity layer 2500-3000m in thickness lay thereunder, and that the lowest layer had a high resistivity of approximately 100 Ohm m. By comparing these data with the geological structure, structures were disclosed corresponding to the rock bed depth, Ukawa syncline, Ishiguro anticline, and Yoneyama mountain mass. 3 refs., 10 figs., 1 tab.

  11. Present state and future of pretrochemical industry; Domestic and overseas situations concerning new and additional construction of facilities of ethylene and BTX. Sekiyu kagaku sangyo no genjo to kongo; Ethylene BTX no shinzosetsu wo meguru naigai josei

    Konuma, Yoshio

    1990-02-25

    Since 1987, petrochemical industry has jumped into the era of properity and as a whole, been supported by increasing demands. Although it is said that the 21st Century is the age of chemistry, but for petrochemistry the age of 1990 {prime} s is the age of international competition for the survival towards the 21st Century. The scale of individual enterprise of the Japanese chemical industry including petrochemical enterprises still remains small when compared with that of the individual world-wide chemical enterprises of the U.S.A., Germany and the U.K., etc., besides these world-wide enterprises have established their production bases and research facilities in Japan. In addition, there is somewhat uncertainty in the foundation which is supporting the present prosperity. This article scans the present situation of petrochemistry in its preface, explains the present state and trends of individual industry in the chapters covering the environment around the Japanese petrochemical industry, the report (summary) of the Long Term Credit Bank Institute of Management, trends of advance of oil industry into petrochemical business, production capacity of ethylene and new as well as additional plant construction plans. In this industry, is observed the constitution of Japan which is unable to form internationally competitive power irrespective of her recognition of its necessity because of their giving priority to the balance of their business world. 1 tab.

  12. Research report of fiscal 1997. Joint research project on petroleum substituting energy between Japan and the EU; 1997 nendo chosa hokokusho. Nichi EU sekiyu daitai energy kanren kyodo kenkyu jigyo

    NONE

    1998-03-01

    Four researchers were invited from EU countries to promote R & D of petroleum substituting energy in Japan, and the joint research was made in institutes of Agency of Industrial Science and Technology related to each theme for 50 days. On the research on deep geothermal prospecting based on volcanic halocarbon group, it was showed that halocarbon discharged from volcanic or hydrothermal system is an important window to survey activities within the earth. On the research on catalyst for hydrogenation of coal-derived liquid, XPS data was reported, and some preliminary conclusions were obtained. On the research on oxide system anode material for Li secondary cells, a method for improving the state of host to ion moving in 1-D to 3-D networks by diffraction method was showed. In particular, the method was effective to offer electronically sensitive environment to moving ion system. On the research on hydro-dechlorination of hydrocarbon halide, the theme related to environmental measures against waste hydrocarbon halide (depletion of the ozone layer) was studied. 83 refs., 32 figs., 20 tabs.

  13. Survey report for fiscal 1998. Joint research project with researchers related to petroleum substituting energies in the EU countries; 1998 nendo EU shokoku no sekiyu daitai energy kanren kenkyusha tono kyodo kenkyu jigyo chosa hokokusho

    NONE

    1999-03-01

    It was intended to invite researchers related to petroleum substituting energies from the EU countries to perform joint researches at research organizations under the auspices of the Agency of Industrial Science and Technology having deep relations with research themes of the invited researchers, to deepen the mutual understanding, and to form efficient cooperative relationship. The intention is also to contribute to research and development of petroleum substituting energies to be used in Japan in the future. The research themes, researchers, their research organizations, and the receiving research organizations are as follows: (1) evaluation of reservoir impedance in high-temperature rock experimental fields by Mr. Ralph Weidler (Germany) at Ruhr University received by the Resource and Environmental Technology Research Institute; (2) changing the particle boundary structure of ceramics by using the alkoxide process by Dr. Ramon Torrecillas (Spain) at Institute Nacional del Carbon received by the Nagoya Industrial Technology Research Institute; (3) research on corrosion in metallic materials for molten carbonate type fuel cells by Dr. Giuseppe Calogero (Italy) at Institute for Transformation and Storage of Energy received by the Osaka Industrial Technology Research Institute; and (4) estimation of behavior of deep geothermal reservoirs with high enthalpy by Dr. Enrico Maranini at Universita' Di Ferrara received by the Geology Survey Center. (NEDO)

  14. Fiscal 1999 report on basic research for promotion of joint implementation programs. Energy saving project for Jingling Petrochemical Corp. Nanjing Refinery; 1999 nendo Jingling sekiyu kako koji Nanjing seiyusho shoene project chosa hokokusho

    NONE

    2000-03-01

    A survey is conducted for the above named plant under an energy saving project expected to link to the clean development mechanism (CDM) of COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). Studies are conducted about the refurbishment of the existing power recovering facilities in the wake of a plan for enhancing FCC (fluid catalytic cracker) processing capability and about power recovery from unused exhaust gas from the RFCC (residual fluid catalytic cracker) second catalyst regeneration tower. A modification plan was drafted and rough designs were prepared therefor, and it was found that power recovery from RFCC would be technologically and economically unfeasible because of the high temperature and extremely small quantity of the recoverable gas. It was then concluded that the plan be abandoned. Thanks to the refurbishment of the existing power recovering facilities to go out of service under the new operating conditions after FCC facility modification and to the installation of a new exhaust gas processor for air pollution prevention, there will be 10.6MW to be recovered for a reduction in fuel for in-house power generation. The consequential reduction in energy consumption will result in a CO2 reduction of 70,000 tons/year. Though China has not yet ratified the COP3 protocol, it is hoped that it will consider emission tradings and participate in the project when designated as a CDM country. (NEDO)

  15. Research report of fiscal 1997. Invitation project of specialists on petroleum substituting energy between Japan and the EU; 1997 nendo chosa hokokusho. Nichi EU sekiyu daitai energy kanren senmonka shohei jigyo

    NONE

    1998-03-01

    Specialists were invited from EU countries for information exchange to promote R and D of petroleum substituting energy in Japan. In the seminar on the present and future trend of R and D of fuel cells in EU countries, the present R and D state of fuel cells in Italy, the present state and future R and D plan of fuel cells in ANSALDO group, the state of SOFC R and D in Germany and by international cooperation, and R and D of polymer electrolyte fuel cell in Fraunhofer institute for Solar Energy Systems were reported contributing to mutual understanding between Japan and the EU. Exchange of opinions and information was also made between 4 fuel cell specialists of EU countries and Japanese specialists. The report on such an exchange includes the outline of Japanese fuel cell technologies, and the present R and D states of phosphoric acid fuel cell (PAFC), molten carbonate fuel cell (MCFC), solid oxide fuel cell (SOFC), and polymer electrolyte fuel cell (PEFC). The specialists visited some government organizations, semi-government organizations, institutes and private enterprises related to promotion, support and verification of R and D of fuel cells. 2 tabs.

  16. Application of magnetotelluric method to hydrocarbon exploration. Case study of MT survey in Yurihara oil and gas field, Akita prefecture; MT ho no kokunai sekiyu tanko eno tekiyo. Akitaken Yurihara chiiki ni okeru jikken chosa kekka

    Mitsuhata, Y; Matsuo, K; Ishikawa, H; Tanaka, H; Nakagami, K [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1996-10-01

    The experiment and survey were carried out to verify the effectiveness and limitation of MT method. The previous seismic reflection method is unsuitable for steep terrain and over-folded complicated geological structure. In such difficult areas, application of MT method is increasing as complement or substitution for the reflection method. However, the evaluation of resistivity structure interpretation for every area is slightly difficult because of lack of data, poor quality of data, and no verification data at boreholes. Consequently, the survey was again carried out in well-known Yurihara oil and gas field, Akita prefecture whose geological structure has been surveyed in detail at boreholes, by adding new 32 sites, 22 sites on the south side and 10 sites on the north side of the measuring line extending from east to west. As a result, it was clarified that the lower high-resistivity layer found by MT method is equal to the Nishikurosawa basaltic layer, and basalt extends to the west in the north area. This result can`t be simply compared with the previous geological profile. 8 refs., 8 figs.

  17. Treatment of bilge and oily drain water of tankers and current measures against combustible oil gas discharge; Tanker no biruji yudakusui shori oyobi kanensei sekiyu gas haishutsu taiskau no genjo

    Agatsuma, Y.

    1996-07-25

    This paper describes the current actual conditions on treatment of bilge discharged from engine area and oily drain water from cargo area of tankers. Clean bilge among various bilges discharged from engine area such as vapor drain, fresh water, rainwater, seawater and condensed water is directly dumped into the sea after temporary storage in a clean tank. Oily bilge is produced mainly by mixing of clean bilge and leakage oil from main engines and various auxiliaries. Oily bilge is dumped into the sea under comparative monitoring of the bilge quality with the dumping standard by oil concentration monitoring and control equipment after the primary treatment in a treatment tank and the secondary treatment in a bilge separator. Oily drain water from cargo area contains water ballast for cargo oil tanks, wash water for tanks and lines, and bilge produced in pump room. The oily drain water is dumped under a specific condition. However, water ballast for specific ballast tanks is excluded from the oily drain water. 2 figs.

  18. FY 1999 report on the basic survey of the promotion of Joint Implementation, etc. Beijing Yanshan Petrochemical Co./cogeneration; 1999 nendo Beijing Yanshan sekiyu kako yugen koji netsu heikyu fukugo hatsuden chosa hokokusho

    NONE

    2000-03-01

    For a combination with COP3 Clean Development Mechanism (CDM), the paper reported the FY 1999 survey of the cogeneration project of Beijing Yanshan Petrochemical Co. The existing two heavy oil fueled boilers (steam output: 240t/h) are dismantled, and two gas turbines and two waste heat boilers (steam output: 241t/h, electricity output: 136.9MW) are installed. The energy conservation effect is approximately 0.91 million tons/year of crude oil. The effect of reduction in greenhouse gas emissions is CO2 2.83 million tons/year. A plan on system interconnection, distribution, electricity, instrumentation control was drawn up. The construction term is planned to be about two and a half years. The initial investment amount is 700 million yuan {+-} 100 million yuan. The expense vs. energy conservation effect was calculated as 98t (crude oil conversion)/year/million yen, and the expense vs. greenhouse gas emission reduction effect 302t-CO2/year/million yen. Concerning the profitability, the generating cost was 0.4 yuan/kWh which dropped from the selling power cost of the Yanshan area, 0.45 yuan/kWh. As candidates of the natural gas fueled cogeneration, there are possibilities of 10 sites and 550MW scale only in the Beijing area. (NEDO)

  19. Environmental science, petroleum engineer`s view. CO2 gas reduction technologies for global warming prevention; Sekiyu gijutsusha no shiten kara no kankyo kagaku. Chikyu ondanka eno taio no tame no CO{sub 2} yokusei gijutsu

    Nomura, K [Tokyo (Japan)

    1998-08-01

    This paper discusses the techniques concerning diesel engines for cogeneration systems, techniques concerning fuel consumption-saving type lubricating oils and techniques concerning oil refineries, out of the CO2 emission control (energy saving) techniques for coping with the global warming which the petroleum engineers are now tackling. The paper introduces CO2 emission control techniques using a petroleum cogeneration system and studies on NOx removing techniques using catalysts as the techniques concerning diesel engines; techniques for reducing friction loss, which occurs in an engine and a transmission, by improving the recipes of lubricating oils and the development of novel friction modifiers as the fuel consumption-saving type lubricating oil techniques; and the CO2 separating techniques using a system for recovering the low-temperature waste heat produced in petroleum refinement with a high efficiency, or using a solid film such as a molecular sieve as the energy-saving techniques used in oil refineries. 18 refs., 8 figs., 1 tab.

  20. Fiscal 1994 report on the survey of making models for introducing petroleum substituting energy systems; 1994 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa)

    NONE

    1995-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. appropriate and concrete guidance for introducing energy systems which meet with features of the areas and buildings and courses for how to construct infrastructures of towns or cities in case of development and redevelopment. Recently, also in local governments, etc., there are seen attitudes toward positive study of introduction of energy conservation systems and petroleum substituting energy systems in case of redevelopment, and the situation is that the spread and expansion are expected by giving appropriate guidance for the introduction. Accordingly, the study makes analyses of the trend and characteristics of developmental projects and makes/arranges models of promising petroleum substituting energy systems, aiming at contributing to promotion of guidance for the introduction to local governments, entrepreneurs, etc. Approximately 20 models of petroleum substituting energy systems were made which are thought to be promising. For each, the following were arranged: outline of system, introduction target, introduction effects, the point of promotion of the introduction, related subsidy systems, actual results, etc. 22 figs., 34 tabs.

  1. FY 2000 survey report on the project on energy conservation/environmental preservation for oil corporations in Croatia by rehabilitation of oil refinery; 2000 nendo Croatia sekiyu kosha muke seiyusho no rihabiri ni yoru shene kankyo hozen project chosa hokokusho

    NONE

    2001-03-01

    For the purpose of strengthening the international competitive force in the oil industry of Croatia and reducing greenhouse effect gas by introducing energy conservation technology, study was made of the rehabilitation of oil refineries (Rijeka and Sisak) of Croatia's oil corporation, INDUSTRIJA NAFTE d.d. (INA). Rijeka and Sisak Refineries have the oil processing capacity of 6 million t/y and 4.6 million t/y, respectively, but they were constructed during the 1960s-1970s and are now superannuated. In this project, the following are adopted: heightening of the temperature of raw material supply, surging avoidance control, reutilization of condensate water of vacuum distillation, heightening of MEA concentration, control of excess air ratio in heating furnace, preheating of combustion air in heating furnace, application of small-diameter pump impeller, the optimum control of steam/electric system, heightening of temperature of cleaning water of desalting device, stop of adoption of flare seal gas, etc. The energy conservation effect to be expected from the project is 43,065 toe/y in a total of the two refineries, and the reduction in greenhouse effect gas is 133,000 t-CO2/y. Further, the internal return rate is 53.12%, which is very attractive for INA. (NEDO)

  2. Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

    NONE

    2000-05-01

    This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

  3. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  4. FY 2000 report on the basic survey to promote Joint Implementation, etc. Feasibility study of the effective utilization of by-product high-sulfur concentration petroleum coke at Fujian Petrochemical Co. Ltd., Fujian Province, China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku sekiyu kako shudan koji fukusei ren'yu kako yugen koji Fujian koio nodo sekiyu cokes no yuko riyo ni kansuru F/S chosa

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas emission, an investigational study was conducted for the project on the effective utilization of high-sulfur petroleum coke at Fujian Petrochemical Co., Fujian Province, China. In the project, IGCC (integrated gasification combined cycle) power generation facilities are introduced to the refinery of Fujian Petrochemical Co. By gasifying the residues produced from the refinery as raw material, the gas clean the same as natural gas is produced and is used as power generation use fuel. As a result of the study, the energy conservation amount was 94,300 toe/y, and was 1,414,500 toe in cumulative amount during 15 years. Further, the amount of greenhouse effect gas reduction was 291,600 t-CO2/y, and was 4,374,000 t-CO2 in cumulative amount during 15 years. The construction cost of the project is approximately 29.7 billion yen. The annual profit to be obtained from the project is approximately 8.66 billion yen, which is indicated by difference between before and after the implementation of the project. The calculated years required for return of investment were 3.4. (NEDO)

  5. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  6. Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

    Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

  7. Development of large scale wind energy conservation system. Development of large scale wind energy conversion system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no kaihatsu

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of large scale wind energy conversion system. The study on technological development of key components evaluates performance of, and confirms reliability and applicability of, hydraulic systems centered by those equipped with variable pitch mechanisms and electrohydraulic servo valves that control them. The study on blade conducts fatigue and crack-propagation tests, which show that the blades developed have high strength. The study on speed-increasing gear conducts load tests, confirming the effects of reducing vibration and noise by modification of the gear teeth. The study on NACELLE cover conducts vibration tests to confirm its vibration characteristics, and analyzes three-dimensional vibration by the finite element method. Some components for a 500kW commercial wind mill are fabricated, including rotor heads, variable pitch mechanisms, speed-increasing gears, YAW systems, and hydraulic control systems. The others fabricated include a remote supervisory control system for maintenance, system to integrate the wind mill into a power system, and electrical control devices in which site conditions, such as atmospheric temperature and lightening, are taken into consideration.

  8. Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

    NONE

    1981-03-01

    This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

  9. Development of small-size transmission tower erection method; Kogata tetto kumitate koho no kaihatsu kenkyu (gaibushiki crane ni yoru kogata tetto kumitate koho no kaihatsu)

    Matsuishi, S.; Asano, J.; Koji, Y. [Kansai Electric Power Co. Inc., Osaka (Japan); Tsujimura, I.; Teramoto, A. [The Kanden Kogyo Incorporated, Osaka (Japan); Sasaki, T.; Mito, K. [AG Ajikawa Corp., Osaka (Japan); Tsuji, M.; Fukumoto, T.; Yamaguchi, N.

    1997-09-30

    To reduce the construction period and cost and to enhance the safety during 77 kV-class transmission tower election, a new method of small steel transmission tower erection using an external type crane has been developed. For the selection of cranes, a commercially available self-climbing crane was employed which has an operating radius of 11 m, a lifting load capacity of 1.5 t, and a lift of up to 60 m. For the space analysis using a model tower, various supporting methods with horizontal supporting members, stress analysis for each tower stub, and apparatuses were examined. For the demonstration tests of election using the model tower, strain gages were attached at each point of steel tower, crane and horizontal supporting members, to measure the stress of members at each stage of the election. It was confirmed that there were no problems. For the election of actual steel tower, the practicality of this method was compared with that of conventional methods. The construction period was reduced in 20%, and the cost was reduced in 4%. The safety of this method was drastically enhanced due to the lack of moving on the tower and less manual operation. 9 figs., 1 tab.

  10. Fiscal 1992 report on geothermal development promotion survey (Development of geothermal reservoir assessment technique); 1989 nendo chinetsu kaihatsu sokushin chosa (Chinetsu choryusou hyoka shuho kaihatsu hokokusho)

    NONE

    1994-03-01

    Efforts were exerted in fiscal 1984-1992 to develop techniques for appropriately assessing a geothermal reservoir for its productivity for duly predicting the optimum scale of power generation to be provided thereby. In the development of simulators, geothermal reservoir simulators (SING-1, -2, -3) and a geothermal well 2-phase flow simulator (WENG) were developed. As for the treatment of fractures in a reservoir and of substances soluble in the hot water, the methods for dealing with them were improved and augmented. In a model field study in a Hokkaido forest, reservoir pressure continuous observation and monitoring, temperature logging and pressure logging for existing wells, and geothermal fluid chemical analysis were performed for reservoir analysis, in which both natural state simulation and history mapping excellently reproduced the temperature and pressure distributions. The temperature and pressure distributions in a natural state simulation, out of the results of an analysis of the Oguni district model field, Kumamoto Prefecture, agreed not only with those in the natural state but also with the pressure transition data in the observation well. (NEDO)

  11. FY1997 geothermal development promotion survey. Development feasibility study 'Ashiro area'; 1997 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa (Ashiro chiiki) hokokusho

    NONE

    1998-12-01

    With regard to the Ashiro Town area in Iwate Prefecture, this paper reports the result of evaluations based on temperature and pressure logging after a lapse of an extended period of time (well No.2) and a steam jet test (well No.1). These activities were performed as the survey on promotion of geothermal development and survey on development feasibility in fiscal 1997. As a result of the overall analysis based on the present survey and ones in the past, the geothermal system model in the surveyed area may be conceived as follows: in both of the N7-AR-1 and N7-AR-2 wells drilled in the southern part of the surveyed area, temperature as high as 250 degrees C or higher was confirmed; the underground temperature is 200 degrees C or higher at an altitude level of zero meter and 250 degrees C at around -500 m, leading to a belief that the high temperature area spreads to south; as a fracture system holding geothermal fluid, a fault was identified at the N7-AR-1 well drilling depth of 1710 m; in the steam jet test, a geothermal reservoir (a shallow geothermal reservoir) was confirmed to exist; the geothermal fluid that has jetted out shows alkaline Na-SO{sub 4} type; and the deep geothermal reservoir has high temperature and is presumed to be in the two-phase condition, presenting promising factors as the geothermal resources. (NEDO)

  12. Feasibility study of Copahue geothermal development project, Argentina; Aruzenchin kyowakoku Copahue chiiki no chinetsu kaihatsu chosa

    Abe, M.; Yamada, M.; Nakanishi, S.; Todaka, N. [Electric Power Development Co. Ltd., Tokyo (Japan); Fujita, T.

    1996-03-15

    Geothermal resources have been evaluated in the Copahue district. For this survey administrated by JICA, drilling of a deep test well with a small bore (COP-3) and blowout tests were conducted. This district is located at the east side of the Andes elongated in the N-S direction. Volcanoes with similar active periods and active states are distributed in the N-S direction, which forms a divide with the Pacific Ocean side. The Copahue-Caviahue composite volcano in the surveyed area is located nearly in the central part of the volcanic zone, which forms a special ring topography. Geology of the Copahue district consists of volcanic effusive rocks during the Tertiary and Quaternary periods. There are five prospecting fields with geothermal indications in the surveyed area. From the survey, an area of about 13 km{sup 2} was evaluated as a geothermal resource field. Especially, in the area of about 4 km{sup 2} including COP-1, 2 and 3 wells, the steam predominant type reservoirs were found out. As a result of estimation of the geothermal resource potential by the volumetric method, a highly prospective power generation potential of 30 MW was evaluated in the field where the steam predominant type reservoirs were confirmed by the boring wells. 7 refs., 13 figs., 1 tab.

  13. Development of measurement apparatus for high resolution electrical surveys; Komitsudo denki tansa sokuteiki no kaihatsu

    Moriuchi, H; Matsuda, Y; Shiokawa, Y [Sumiko Consultants Co. Ltd., Tokyo (Japan); Uchino, Y [Cosmic Co. Ltd., Tokyo (Japan)

    1996-05-01

    For the enforcement of the {rho}a-{rho}u survey method which is a type of high-density electrical survey, a multichannel resistivity measuring instrument has been developed. This instrument, in addition to the above, conducts resistivity tomography and various other kinds of high-density electrical survey. A potential produced by a low frequency rectangular current of 1Hz or lower outputted by the transmitter of this instrument is received and measured by the receiver connected to electrodes positioned at 100 or less locations. The receiver comprises a scanner that automatically switches from electrode to electrode, conditioner that processes signals, and controller. A transmitter of the standard design outputs a maximum voltage of 800V and maximum current of 2A, making a device suitable for probing 50 to several 100m-deep levels. The receiver is operated by a personal computer that the controller is provided with. The newly-developed apparatus succeeded in presenting high-precision images of the result of a {rho}a-{rho}u analysis for an apparent resistivity section and of the underground structure, verifying the high quality of the data collected by this apparatus. 10 refs., 5 figs., 1 tab.

  14. Development of S-wave portable vibrator; S ha potable vibrator shingen no kaihatsu

    Kaida, Y; Matsubara, Y [OYO Corp., Tokyo (Japan); Nijhof, V; Brouwer, J

    1996-05-01

    An S-wave portable vibrator to serve as a seismic source has been developed for the purpose of applying the shallow-layer reflection method to the study of the soil ground. The author, et al., who previously developed a P-wave portable vibrator has now developed an S-wave version, considering the advantage of the S-wave over the P-wave in that, for example, the S-wave velocity may be directly compared with the N-value representing ground strength and that the S-wave travels more slowly than the P-wave through sticky soil promising a higher-resolution exploration. The experimentally constructed S-wave vibrator consists of a conventional P-wave vibrator and an L-type wooden base plate combined therewith. Serving as the monitor for vibration is a conventional accelerometer without any modification. The applicability test was carried out at a location where a plank hammering test was once conducted for reflection aided exploration, and the result was compared with that of the plank hammering test. As the result, it was found that after some preliminary treatment the results of the two tests were roughly the same but that both reflected waves were a little sharper in the S-wave vibrator test than in the plank hammering test. 4 refs., 9 figs., 1 tab.

  15. Development of new-concept superconducting power equipment; Shinkino chodendo denryoku kiki no kaihatsu

    Hamajima, T.; Tsurunaga, K.; Urata, M. [Toshiba Corp., Tokyo (Japan)

    1998-01-01

    The superconducting magnet energy storage (SMES) system has a function by which magnetic energy is stored in a superconducting coil without loss and discharged very rapidly into the power line when needed. The fault current limiter has a function by which transport current is passed without impedance and excessive fault current is restricted by generating large impedance in an emergency. These are the functions of new power equipment, which can not be realized by the conventional equipment. In the small-scale SMES project, Toshiba has fabricated 100 kWh-class element coils and 1 kWh/1 MW modules as the first step of practical application for power system control. For the superconducting fault current limiter, Toshiba has developed a 6.6 kV-1 kA class fault current limiter without supplying cooling medium such as helium, and limiting tests of fault current have been successfully conducted. Through the long-term tests of element coils for SMES and the system interconnection tests of module-type SMES, it is expected that the technological development for practical application is accelerated. 4 refs., 7 figs., 3 tabs.

  16. Development of a water hydraulic servovalve; Suiatsu servo ben no kaihatsu

    Urata, E.; Nakao, Y. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering; Yamashina, C.; Miyagawa, S.; Usami, Y.; Shinoda, M. [Ebara Research Co. Ltd., Kanagawa (Japan)

    1997-06-25

    An electrohydraulic servovalve that uses clear water as a pressure medium (water hydraulic servovalve) is developed. A conventional electrohydraulic servovalve cannot work with this hostile fluid. This paper explains the structure and functions of components, and the relationship between them, as well as development procedure of the water hydraulic servovalve. The basic idea for the development is to support the spool of the valve with hydrostatic bearings and to lead the water from the bearings to the flapper-nozzle system, which, in this valve contains a laminar restriction upstream from the nozzle instead of the turbulent restriction in the conventional flapper-nozzle system. This paper also explains the design procedure of the hydrostatic bearing in the valve and the connection of electromagnetic elements and the fluidic elements. The manufactured water hydraulic servovalves show good characteristics in their smooth motion, endurance and controllability, including dynamic characteristics. 25 refs., 12 figs.

  17. Development and utilization of liquid quartz light modulating film. Ekisho choko film no kaihatsu to riyo

    Takahashi, M. (Ajinomoto Co. Inc., Tokyo (Japan))

    1992-03-01

    This paper introduces the polymer dispersed liquid crystal (PDLC) ACT'' sheet, a liquid quartz light modulating film, developed by the Ajinomoto Company in Japan. A mixture of liquid crystal and polymer precursor is sandwiched between polyethylene terephthalate films imparted with transparency conductor made of indium tin oxide (ITO), which is then polymerized by heating or irradiating ultraviolet rays to obtain a PDLC. The film has a thickness as thin as about 0.3 mm, and good processibility. The sheet uses light modulating elements functioning on scatter and permeation of light. Clarification was made on the voltage dependence of cloudiness, total light permeability, straight and parallel light permeability, the response, and the operating voltage. The system consumes small amount of power with a threshold value of about 35V, and is suitable to operate large areas when working on the utility power supply. An incident light having a high diffusion capability when the electric field is turned off exhibits a high clouding function. The system gives an excellent feel of colorlessness and transparency when the electric field is turned on. The performances in heat insulation, infrared reflection capability and noise resistance are expected to be compounded for a functional versatility. 4 refs., 6 figs., 2 tabs.

  18. How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

    Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

    1999-07-05

    They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

  19. Research and development project plans for FY 1995; 1995 nendo kenkyu kaihatsu jigyo keikaku

    NONE

    1995-04-01

    The present research and development project plans for FY 1995 administrated by NEDO consist of research and development of new energy, and research and development of industrial technology. Are illustrated further enhancement of new energy introduction promotion measures, new stage of international projects, promotion of new energy and new energy technology development, further enhancement of industrial and scientific technology research and development, integrated measures against global and urban environment problems, and budget of NEDO projects in FY 1995. The research and development of new energy includes coal conversion technology, solar energy technology, geothermal energy technology, energy conversion and storage technology, hydrogen, alcohol and biomass energy technology, geothermal energy resources, coal resources development, new energy promotion department activities, NEDO information center activities, and so on. On the other hand, the research and development of industrial technology includes research and development of industrial technology, and global environment technology. The research and development of industrial technology consists of superconductivity, new materials, biotechnology, electronics, information and communications, machinery and aerospace, natural resources, humanity, life and society, and various leading researches.

  20. R and D of remote reading system. Remote reading system no kaihatsu kenkyu

    Nakano, H.; Hamada, T.; Nakamura, O. (The Kansai Electric Power Co. Inc., Osaka (Japan)); Imai, Y.; Akiyama, K.

    1992-03-25

    As measures for the spots difficult in metering within a framework to integrally automate the power distribution, a remote reading system was prototypically tested and evaluated in reliability on the actual field. The system methodically selected the signal {prime}s line injection, high frequency wave signal and voltage detection, while the signal frequency, transmission rate and highest transmission output were set at approx. 3.5KHz, 7.5bps and 50dBm, respectively from the test result. The demonstration test on reliability of the system locatively selected a vicinity of high voltage consumer, high harmonic wave-generating consumer, transforming station, etc. The total ratio of success in reception was comparatively high in Kuzuno and Yamazaki areas, but low in Kamojyo and Ichinomiya areas, The badness in reception was caused by the fluctuation in noise and strongness in damping which was influenced by the condenser in the high voltage consumer. The locative relation between the parent and child stations of system, and high voltage consumer being classified into four patters, an application table of remote reading system was prepared by simulation. 14 figs., 6 tabs.

  1. Development of sound absorption measuring system with acoustic chamber; Kogata kyuon koka sokutei sochi no kaihatsu

    Takahira, M.; Noba, M. [Toyota Motor Corp., Aichi (Japan); Matsuoka, H. [Nippon Soken, Inc., Tokyo (Japan)

    1998-05-01

    In order to measure sound absorption performance necessary to develop sound absorption materials, development was made on a device consisting of a small sound box capable of measurement inexpensively and easily, as a measure against the reverberation chamber method. In order to obtain stabilized diffusion sound internally, the sound box has a shape of asymmetric seven-side body in which sides do not face squarely with each other. The box was so sized that a large number of resonant vibration postures can be constituted at the targeted frequency simultaneously in the box. The box has a commercially available cone speaker with good acoustic output characteristics in frequency range of higher than 500 Hz installed on an inner side of the box. The sound source uses a method to derive sound absorption rate from difference of sound pressure levels. In order to eliminate need of averaging treatment by using a multi-point measurement inside the box, a discussion was given to provide an opening on part of the box to place the sound receiving point outside the opening. A square test piece is placed on the floor 0.5 meter or more away from the speaker in the box. As a result of the experiment, it was verified that the sound absorption rate obtained by this device corresponds well with that by the reverberation chamber method. The size of the test piece was also found adequate. 2 refs., 11 figs., 1 tab.

  2. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  3. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  4. Development of hydraulic brake actuator for active brake control; Active brake seigyoyo yuatsu booster no kaihatsu

    Konishi, Y; Hattori, M. Sugisawa, M.; Nishii, M [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, application of active brake control systems of the vehicle are increasing. (Vehicle stability control, Panic brake assist ) We have developed a new hydraulic brake actuator for active brake control systems. New hydraulic brake actuator is composed of the three parts. (Hydraulic booster unit, Power supply unit, Control valve unit) This report describes the construction of the new hydraulic booster unit. 2 refs., 10 figs.

  5. Development of crankshaft dynamic stress prediction; Jitsudoji crankshaft oryoku yosoku shuho no kaihatsu

    Takahashi, S; Iwamoto, A; Miyazawa, H; Sato, K; Ozaki, H [Honda R and D Co. Ltd., Tokyo (Japan)

    1997-10-01

    In this paper, the development of the simulation model which predicts the stress of the crankshaft under running condition precisely is described. This simulation model considers about the nonlinearity of the oil film stiffness in the main bearing, the dynamic characteristic of the crankshaft system including resonance and the cylinder block stiffness. By the development of this stress analysis simulation, the stress m each part of the crankshaft during durability testing could be precisely predicted. 1 ref., 10 figs.

  6. Development of friction welding method by electric servo motors; Dendo servo shiki masatsu assetsuho no kaihatsu

    Suzuki, H; Onuma, M; Hasegawa, T; Sakamoto, T [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The standard friction welding has two methods; the brake method and the inertia method. We have developed a new friction welding method with the electric servo motor system. The forming of plastic fluidity layers of interface is evaluated quantitatively with the feedback control characteristics. The new method has enabled to reduce the heat effect and the burr of friction welding. In the method, we could reduce the getting heat energy, from one-third to half less than the previous methods. 6 refs., 16 figs.

  7. Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

    Seto, Y; Inoue, H [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

  8. Hierarchical functional model for automobile development; Jidosha kaihatsu no tame no kaisogata kino model

    Sumida, S [U-shin Ltd., Tokyo (Japan); Nagamatsu, M; Maruyama, K [Hokkaido Institute of Technology, Sapporo (Japan); Hiramatsu, S [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    A new approach on modeling is put forward in order to compose the virtual prototype which is indispensable for fully computer integrated concurrent development of automobile product. A basic concept of the hierarchical functional model is proposed as the concrete form of this new modeling technology. This model is used mainly for explaining and simulating functions and efficiencies of both the parts and the total product of automobile. All engineers who engage themselves in design and development of automobile can collaborate with one another using this model. Some application examples are shown, and usefulness of this model is demonstrated. 5 refs., 5 figs.

  9. Development of catalyst for diesel engine; Diesel engine yo shokubai no kaihatsu

    Ueno, H; Furutani, T; Nagami, T [Toyota Motor Corp., Aichi (Japan); Aono, N; Goshima, H; Kasahara, K [Cataler Industrial Co. Ltd., Shizuoka (Japan)

    1997-10-01

    The new concept catalyst for diesel engine has been developed. When the exhaust temperature is low, SOF and HC are temporarily adsorbed by the adsorbent within the catalyst and are oxidized as the temperature rise. The process of this development have manifested as follows. (1) The coating material is important factor to govern the oxidation activity. (2) SOF is reduced by the coating material in low temperature less than 200degC. (3) The coating material, which has low SO2 adsorbing rate suppress the sulfate formation at high temperature. 2 refs., 11 figs., 1 tab.

  10. Development of super thin foil metal supported catalyst; Chousuhaku metal tantai shokubai no kaihatsu

    Sanji, F; Takada, T [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    In order to improve warm-up performance, high heat resistance and long life durability of catalysts, the reduction of the metal support heat capacity has been focused. The effects of both reducing foil thickness and lowering cell density on low heat capacity have been investigated. As a result of engine bench and vehicle test, it was apparent that the reduction of foil thickness has greater effects. Newly developed 30 {mu} m foil thickness metal supported catalyst has quicker warm-up performance, and its structural durability up to 950degC is confirmed. 3 refs., 11 figs., 1 tab.

  11. Development of low light-off catalyst; Teion kassei ni sugureta shokubai no kaihatsu

    Takemoto, T; Ichikawa, S; Koda, Y; Yamamoto, E; Sumida, H; Yamada, H; Shigetsu, M; Komatsu, K [Mazda Motor Corp., Tokyo (Japan)

    1997-10-01

    A new type of three way catalyst was developed in order to reduce HC, CO and NOx in cold exhaust gas. This catalyst consists of double layer, and has a base support material of alumina and oxygen storage components (OSC) loaded with active metals including platinum. palladium and rhodium. It has good light-off performance and high catalytic activity. This catalyst includes two types of OSC. One is CeO2, and the other is CePrO2 that makes possible to improve NOx conversion at high exhaust gas temperature. 8 refs., 13 figs., 2 tabs.

  12. Development of an automatic emergency reporting system; Jiko jido tsuho system no kaihatsu

    Kawai, A; Sekine, M; Kodama, R; Matsumura, K [Nissan Motor Co. Ltd., Tokyo (Japan)

    1995-06-30

    This paper proposes an automatic emergency reporting system as an ASV technology for preventing secondary damage. In the event a vehicle is involved in an accident or other emergency situation, this system automatically reports the vehicle`s present position along with information on the vehicle and owner to an operations center via radio signals. This makes it possible to dispatch an ambulance or other emergency vehicle more quickly. A prototype simulation system has been built consisting of a custom designed control unit for in-vehicle use and a personal computer that simulates an operations center. The interface between the control unit and the personal computer is a wireless modem. The navigation system offered in the Cedric was modified for use as the vehicle location sensor and map database of the operations center. In experiments conducted on the system, information was transmitted from the control unit and shown on a digital map display on the personal computer screen in about ten seconds following activation of an emergency signal. 5 figs.

  13. Both hydrogen and electricity chargeable battery; Suiso to denki de juden kanona denchi kaihatsu

    NONE

    1999-06-01

    Kuriyama group of the Osaka Industrial Research Institute developed a new air-metallic hydride battery that is chargeable by both electricity and hydrogen gas. The battery uses a hydrogen storage alloy as the negative pole and uses active carbon coated with platinum as the positive pole. Potassium hydroxide aqueous solution is used as the electrolyte, and a space is arranged in the negative pole for contacting and absorbing the hydrogen with a good efficiency. The key point is the development of the hydride for energy storage that can well absorbs the hydrogen gas even it is dampened by the electrolyte. And the pole is prepared by pulverized the particles of rare earth hydrogen storage alloy having the particle size smaller than 150 micron meter, forming a Ni layer for a catalyst to absorb hydrogen, adding fluorinated resin dispersant for the sake of repellency and forming a sheet. In a test running, a half of hydrogen storage capacity is realized by charging for 30 minutes. And, 0.6 V electricity of 10 mA per unit pole area of 1cm{sup 2} is continuously obtained for 17 hours during discharging. While a third electrode is formed by nickel hydroxide, the battery is chargeable and dischargeable as the same as nickel hydrogen battery. Low cost and small size can be expected by a combination of respectively prepared fuel battery with nickel hydrogen battery. (translated by NEDO)

  14. Hydrogen battery car developed in Matsuda; Matsuda suiso nenryo denchisha wo kaihatsu

    NONE

    1999-06-01

    Matsuda announced that the hydrogen battery car 'Demio FCEV' was developed by the company. This new type car not only does not need an air humidifying machine, but also supplies the necessary electricity with an ultra capacitor of a large scale condenser. Its maximum output is 40 kw, the highest speed is 90 km per hour, and the accelerating time from the stop state to 40 m is about 5 seconds, the same level as a gasoline car. One time of hydrogen charging serves for 170 km running. As a hydrogen battery car, it is the third one in the world, following the DAIMURA in Germany and TOYOTA. (translated by NEDO)

  15. Study on the current status of biomass energy development; Bio mass energy no kaihatsu jokyo chosa

    NONE

    1996-03-01

    A survey was conducted on the present status of biomass energy in Japan and abroad and the developmental trend of the latest biomass energy technology. Brazil and the U.S. are most advancing in the biomass energy utilization. Brazil uses sugar cane which is plenty in supply as a raw material, and the U.S. does corn which is the surplus crop. Both countries use the conventional ethanol fermentation technology and produce the petroleum substitution liquid fuel which is in greatest need. As to the technology to convert biomass resource into energy, attention has so far been paid to the development of the production process of the liquid fuel. The latest technology for ethanol fermentation using saccharin and starch as raw materials has already been established in Japan, and the energy-saving type alcohol recovery technology has also reached the stage of practical application. Moreover, as to the ethanol conversion technology with cellulose substrate, the development of the saccharification process will be needed in future. 15 figs., 10 tabs.

  16. Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

    Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

    1994-07-25

    With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

  17. Development of a new automotive navigation system; Shingata navigation system no kaihatsu

    Sone, M; Nakano, H; Nakayama, O; Tanemura, E; Yoshitsugu, N; Watanabe, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1996-01-31

    An automotive navigation system was outlined. Features of this system are described below: map display called `Bird View` extending up to the horizon was commercialized; accuracy of determining the vehicle`s present position was realized using new algorithm; and automatic route selection was adopted. Human machine interface of this system also was completely reviewed. `Bird View` was realized by reading plane map data out from CD-ROM and converting them onto the coordinate on the virtual screen in front of the view point. Automatic selection which depends mostly on self-contained navigation adopts the certain way in comparison of the computation position in GPS. To assume vehicle advancing direction, employed were optical fiber gyroscope, geomagnetic sensor, and Karman filter making a good use of advantages of GPS, for the improvement of accuracy. For the automatic distance correction, a function of correcting pulse-distance conversion coefficient was employed, and the free maintenance was realized. 5 figs.

  18. Development of a method to maintain vigilance level; Kakusei teika keigen shuho no kaihatsu

    Okamoto, Y.; Horiguchi, A.; Ishida, K.; Hata, S. [Mazda Motor Corp., Hiroshima (Japan)

    1995-04-20

    As a part of measures to prevent accidents caused by reduced vigilance and drowsiness of drivers, this paper reports the result of experiments that presents effectiveness of a method to give drivers intermittent auditory stimuli as environmental stimulation. It was found that vigilance decline can be reduced by intermittent auditory stimuli under a laboratory condition using a selective reaction time in monotonous selective reaction works as a parameter; and the effective interval in the intermittence is 30 seconds. A driving simulator was used to prove that the vigilance decline reducing effect by the intermittent auditory stimuli has the same level of effect as chewing gums even under the environment composed of driving operation, vehicle motions, and background noise. However, a number of questions remain yet to be discussed, such as the effect when the ratio of sound presentation time and no presentation time was varied. Furthermore, a number of other physical stimuli in addition to auditory stimulation may be assumed that has effective possibility as vigilance decline reducing stimuli, including hot heat and vibration. It was verified, however, that vigilance decline can be reduced by properly varying the environmental stimulation. 6 refs., 15 figs., 1 tab.

  19. Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

  20. Development and environment of new electric automobile, `Ecovehicle`; Shingata denki jidosha eko vehicle kaihatsu to kankyo

    Shimizu, H [National Inst. for Environmental Studies, Tsukuba (Japan)

    1996-10-27

    This paper introduces history of the development of an electric automobile, `Ecovehicle`. It is provided with a high overall energy efficiency compared with an engine vehicle. The Ecovihicle is 1.2m in width, 3.3m in length, 2 seating capacities and 910kg in overall weight with serially connected 56 batteries of each 4V, 40Ah and having the total weight of 269kg. Its travel distance per charging is 130km at a speed of 80 k.p.h. This vehicle is capable of running with an energy of approximately one third as much as that of a light car. In addition, the vehicle is provided with polycrystal solar batteries placed on 0.6m{sup 2} area on the roof and spoiler generating 60W maximum. Assuming the annual duration of sunshine is 1,800 hours, charging is possible for 63kWh annually. Assuming the charging efficiency is 83%, charging is possible about seven times, which is an equivalent of travelling about 1,000km annually. The characteristics for example are the employment of brushless DC motor, use of energy saving switching element IGBT in order to realize a low level of loss in the inverter, in-wheel motor system, and storage of storage batteries in a hollow aluminum frame installed under the floor. 2 refs., 5 figs., 1 tab.

  1. Development of RaRaII solar car. Solar car RaRaII no kaihatsu

    Ohashi, M [Toyota Motor Corp., Aichi (Japan)

    1991-05-31

    A solar car was developed to be able to travel, by utilizing solar energy, as a guiding car for the marathon race in the public road. That car is 210kg in weight, 1 in number of riding persons and 4.8m in smallest rotating radius. Its traveling performance is 44km h in highest speed, 10{degree} in hill-climbing ability and 0.6m s{sup 2} in acceleration. Those principal particulars satisfied the required condition of guiding car for the marathon race. That car was equipped with a polycrystalline silicon type solar cell, 6m{sup 2} in area to generate 870Wp power. A silver oxide-zinc battery, used as a secondary battery to secure traveling in case of rain, is of a performance to travel twice the marathon race road through. To satisfy the public road traveling in safety standard, that car was equipped with head lamps, wiper, direction winkers, rear-view mirrors, etc. As material of the body, aramid fiber and carbon fiber were adopted for securing the rigidity to cover the lightening in weight. That car, as used at an opportunity of intercollegiate marathon relay race, traveled a distance of about 30km which was its entire public road portion of course. 2 figs., 2 tabs.

  2. Development and demonstration of optical polarization controller; Hikari henpa seigyo sochi no kaihatsu to jissho

    Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    If fiber transmission light can be controlled in a stabilized polarization state, realization of coherent optical communication is anticipated. In the case of adopting it to OPGW, however, it is necessary to compensate high speed polarization variation caused by lightning strike. But this was difficult in the conventional method. Accordingly, a high speed polarization control method was proposed which uses an electric effect of lithium niobate (LN) crystals. In the study, a polarization control unit was manufactured based on the method proposed and the performance was demonstrated. As a result of measuring output light with input light changed in every state of polarization, the object horizontal polarization component obtained a stabilized light intensity at {+-}0.1dB, and a light intensity of the component slipped out of the horizontal polarization was suppressed under -20dB. To cope with the polarization variation by lightning strike, it is necessary to make the control delay 10{mu}sec or below, and improvement in processing unit, etc. may make it possible since LN crystals respond below 1{mu}sec. High speed control of the infinitely continuing arbitrary polarization variation became possible. 14 refs., 19 figs.

  3. Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

    Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

    1996-06-01

    Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

  4. Development of the Nissan hydraulic active suspension. Nissan yuatsu active suspension no kaihatsu

    Kawarasaki, y.; Fukunaga, Y.; Hasegawa, S.; Okuyama, Y.; Omura, I.; Takahashi, K.; Abe, S.; Tsuruta, E. (Nissan Motor Co. Ltd., Tokyo (Japan))

    1989-12-25

    A hydraulic active suspension system, Nissan original product, was developed and mass produced for the first time in the world. The system incorporates a sufficient power source, a high accuracy sensor and a high response device for continuous and intended vehicle control and at the same time delivers high levels of ride comfort and driving performance. The suspension system has four innovative features: skyhook damping, active roll and pitching control, a frequency-dependent damping mechanism, and active steering characteristics control. Under all road and operating conditions, the system actively suppresses vehicle attitude changes and unnecessary movement, and also gently absorbs inputs from the road. This epoch-making system provides a dramatic improvement in vehicle performance, and has been adopted in the Infiniti Q45 luxury sedan. 2 refs., 20 figs., 4 tabs.

  5. Radar system for non-excavation flowmole drilling; Flowmole koho zenpo kanshi sensor no kaihatsu

    Nakauchi, T; Hayakawa, H; Tsunasaki, M; Kishi, M [Osaka Gas Co. Ltd., Osaka (Japan)

    1997-10-22

    Technology is discussed of detecting structures buried in the ground by use of a forward-looking sensor mounted on the drill head for the avoidance of collision with such structures during application of the flowmole method in urban districts. In this detection system, pulsating radio signals are emitted from a transmission antenna and the received signals are converted into low-frequency signals in a sampling circuit for eventual display on a B-scope. Since the drill head for flowmole technology is as small as approximately 50-60mm in diameter, experiment is conducted to know the detectability of a very small antenna directed at a buried pipe. The basic phase of the experiment using the very small antenna includes a soil-filled tank test and field test. It is then found that the very small antenna is capable of detecting the steel pipe buried 50cm away from the antenna with the antenna directed at the said pipe. In a test wherein a very small antenna is allowed to rotate on the drill propelling shaft, the design simulating a revolving drill head, it is learned that the detecting system under study will identify the direction in which a buried structure exists. 1 ref., 9 figs.

  6. Development of the sex quality of the material for high; Kotaiyosei suritto puragu zaishitsu no kaihatsu

    Egashira, R. [TYK Corp., Gifu (Japan)

    1999-02-01

    When it works for the stable durability of the gas business slit flag, a spooling is made a problem like heat, and the improvement of the quality of the material is being done. It is formed, and a thermostability spooling causes curving, and the existence of that gap is being improved by substituting some of the bone materials for the special alumina bone material during the bone material and the matrix by being connected with the resistance of the crack development the gap when a crack develops, it branches off .A stable durability is confirmed even in an actual opportunity, and heat shock crack resistance Rst is placed on the effective method as an evaluation of the thermostability spooling. (translated by NEDO)

  7. Research and development of turbofan engine for supersonic aircraft. Choonsokukiyo turbofan engine no kenkyu kaihatsu

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1992-01-01

    This paper described the researched results of the demonstrator of a turbofan engine for supersonic aircraft (IHI-17). A turbofan engine with an afterburner was experimentally fabricated and various engine tests have been carried out since 1988. Although the engine size is small, the fighter engine specifications were applied to its design and the prior or simultaneous research on each component was carried out. As a result, the system integration technique by which an engine was assembled by integrating each component could be established. New materials and new manufacturing techniques such as turbine blades of single crystal, turbine disks of powder metallurgy and deep chemical milling for a duct were developed to use for the long term engine test and the prospect to commercialization could be obtained. The following techniques have been established and the results satisfying target specifications could be achieved: the three dimensional aerodynamic design of compressor and turbine, the adoption of air blast fuel atomizer to suppress the smoke generation, an afterburner of spray bar system and the mounting type FADEC (full authority digital electronic control) to control the engine with the afterburner. 4 refs., 15 figs., 4 tabs.

  8. Development of GE90 engine with largest thrust. GE90 engine no kaihatsu jokyo

    Aono, H [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The present paper explained the turbofan engine GE90 which is being developed by General Electric Co., USA. That engine is to meet the thrust (takeoff thrust) of 300 to 530kN as required for the new-generation wide-fuselage civil transport plane which is being designed for its planned operation in the 1990's. In April, 1991, the world's strongest thrust of 480kN was achieved with engine elements also confirmed through element test. Thereafter, the engine underwent a flying test on board of Boeing 747 to materialize the planned operation in 1995. Made to be 9 in by-pass ratio and about 40 in overall pressure ratio, the GE90 was given the concept that advantage could be secured in both propulsive efficiency and thermal efficiency. That concept could be materialized by the development of composite fan blade technology and energy-efficient technology which were both demonstrated with an unducted fan. In spite of its pressure ratio of 22, the GE90's high pressure compressor demonstrates its polytropic efficiency which is equal to that of the low pressure ratio compressor. 3 refs., 19 figs., 1 tab.

  9. Development of high reliability dual redundant FADEC. Koshinraisei nijukei FADEC no kaihatsu

    Endo, M [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The control unit of gas turbine for the aircraft jet engine use must draw overall performance in compliance with the thrust commanded by the pilot under all flying conditions of the engine. High reliability is required in flight safety. The present paper explains a developed unit of dual redundant FADEC (full authority digital electronic control) and high-density mounting technology for the electronic devices required by the FADEC. The FADEC unit is composed of two hardware systems with their respective microprocessors of the same structure. Each of both systems can solely control the engine, while they are both commanded by a necessary signal for the dual system operation and connected through a digital by-pass which can exchange the input/output data between them. For the operational confirmation of FADEC unit, its control characteristics were inspected by intentionally putting it out of order at the time of engine acceleration/deceleration and other transient operations. The control system could be switched without control characteristics lost of the engine. 9 figs., 2 tabs.

  10. Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

    1994-01-01

    The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

  11. Development of plastic pulley by injection molding; Shashutsu keisei ni yoru jushi pulley no kaihatsu

    Yoshizumi, F; Funatsu, A; Yazawa, H [Sumitomo Bakelite Co. Ltd., Tokyo (Japan)

    1997-10-01

    We developed plastic pulley for automobile manufactured by injection molding which will reduce manufacturing cost. We have developed product design, injection molding technology especially to improve mechanical strength and phenolic molding compound with good wear resistance and high mechanical strength. We have established `Injection Compression molding` technology to improve mechanical strength of weld portion. We also developed phenolic molding compound which is composed of one step resin and long organic fiber to obtain good wear resistance and high mechanical strength. Manufacturing cost will be reduced by using injection molding combined with lower material cost of the newly developed compound. 12 figs., 2 tabs.

  12. Development of puncture resistance tire tube; Nirinsha no taipankusei kojo cube no kaihatsu

    Yamagiwa, T; Nakayama, K; Kiyota, S; Tanaka, A [Honda R and D Co. Ltd., Tokyo (Japan); Makisaka, N

    1997-10-01

    A new tire tube with a puncture resistance function was developed. The tube is a two-chamber structure having an air chamber and a liquid chamber, and the liquid chamber at the crown-side half of the tube is filled with an anti-puncture sealant during a manufacturing process. In a market test, it was confirmed that the number of puncture cases were reduced by 90 % in comparison with conventional tire tubes by using the newly developed tube. This paper describes the structure of the tube and the characteristics of the tube rubber, and the manufacturing process and durability of the tube. 3 refs., 17 figs.

  13. Advanced soft coverpad made of non-woven fabric; Soft fushokufu coverpad no kaihatsu

    Hayakawa, t; Kamezaki, K; Tokita, T [Takashimaya Nippatsu Kogyo, Aichi (Japan); Yamada, Y; Ono, H; Araki, O [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    At the present expected to enhance the product-value of automobile, it can be considered that advancement of touching and fitting feeling of seat would be important factors. For the purpose of materializing of these factors, We have noted softening of seat cover and carried out development of cover pad made of non-woven fablic. As a result of pursuing compatibility of soft feeling and durability of the cover pad, we could achieve to ensure the quality required for the material as the seat cover pad. 3 refs., 15 figs., 4 tabs.

  14. Development of air fuel ratio sensor; A/F sensor no kaihatsu

    Sakawa, T; Hori, M [Denso Corp., Aichi (Japan); Nakamura, Y [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The Air Fuel Ratio Sensor (A/F sensor), which is applied to a 1997 model year Low Emission Vehicle (LEV) was developed. This sensor enables the detection of the exhaust gas air fuel ratio, both lean and rich of stoichiometric. It has an effective air fuel ratio range from 12 to 18 as required for LEV regulation. It has the fast light off, - within 20 seconds - to minimize exhaust hydrocarbon content. Further, it has fast response time, less than 200 msec, to improve the air fuel ratio controllability. 3 refs., 7 figs.

  15. Advanced slab polyurethane foam with feather touch; Soft feather urethane foam no kaihatsu

    Yamada, Y; Ono, H [Toyota Motor Corp., Aichi (Japan); Mori, A; Yamaguchi, N; Nakamura, T [Bridgestone Corp., Tokyo (Japan)

    1997-10-01

    Automotive seat plays an important part, which are not only retention of sitting position, but also comfort and high-class feeling. Wadding, which is a part of the seat, is a key component for the sitting comfortableness. This paper is concerned with advanced slab polyurethane foam with feather touch feeling. The compounding of formation, foaming process and reliability of mass production is studied. 2 refs., 10 figs., 3 tabs.

  16. Development of multiplexing network for air conditioner systems; Eakon yo LAN system no kaihatsu

    Matsumoto, T; Nakazawa, Y; Nakase, M; Sato, Y [Nissan Motor Co. Ltd., Tokyo (Japan); Nomura, M; Okasato, Y; Sunaga, H [Calsonic Corp., Tokyo (Japan)

    1997-10-01

    Plural air flap actuators of the air conditioner system in a vehicle have been integrated into a single-type actuator using two newly developed technologies: super-low-cost multiplexing network technology and digital motor control technology with a 1-bit A/D converter. The number of harnesses and connectors and the handling load of the air conditioner control microcomputer are reduced, so that we succeeded in sharply reducing the cost of the air conditioner system. 9 figs., 2 tabs.

  17. Development of hybrid system for mass productive passenger car; Joyoshayo ryosangata hybrid system no kaihatsu

    Abe, S; Sasaki, S; Matsui, H; Kubo, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The Toyota Hybrid System has two power sources which engage depending on driving conditions. An improved efficiency gasoline engine provides the main power to drive the wheels, as in conventional automobiles. Drive power can also be supplied by an electric motor, which derives its electricity from a battery and a Generator. Fuel efficiency is further boosted by other measures, such as automatically cutting the engine when the vehicle is at a stop and regenerating the energy accumulate during deceleration. Compared with conventional vehicles with a 1.5-liter engine running in 10 {center_dot} 15 mode, the CO2 emissions are reduced by half. Moreover, with the use of a motor to reduce engine load during acceleration, HC, CO, and NOx emissions are cut significantly low levels. 13 figs.

  18. Development of Toyota new 1GZ-FE engine; Shingata V12 gasoline engine no kaihatsu

    Kawamura, H; Asahi, T; Goto, M; Endo, K; Terada, M [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The first V-12 cylinder engine for passenger car in Japan, the 1GZ-FE, which is the status of high luxury vehicles has been developed. In order to proceed the merit of V-12 cylinder engine, Intelligent Variable Valve Timing (VVT-i) system, Slant squish combustion chamber, Iridium pole spark plug and Intelligent electronic throttle control system were introduced. Through these features this new 1GZ-FE has achieved an overwhelming smoothness and quietness and yet highest torque among the same displacement engine at low and medium engine speed. Additionally the 1GZ-FE achieved good fuel economy and high reliability which exceed any other competitors. 14 refs., 4 figs.

  19. Development of roller type side slip tester; Roller shiki side slip tester no kaihatsu

    Nishiyama, S [Hiroshima City Industrial Technology Institute, Hiroshima (Japan); Harada, S; Harada, K

    1997-10-01

    This paper presents a new development of roller type side slip tester (RTSSI). The test equipment consists of four parts, which are developed in this research. These are a roller part, a control part, a remote control part and a CRT part. In this study, we especially investigated the mechanism and performance between tire and roller. We analyzed the amount of side slip with various toe angles. The developed tester is examined under the conditions that is considered in industrial applications. We investigated the influences of toe angle, size of tire, pressure of tire, coefficient of friction between tire and roller, pushing force of tire, revolution velocity of roller, axle load and so on. The validity of the developed RTSST is confirmed under these conditions. It was found that the RTSST can be used in practical use. Some measurement results are presented in the form of parametric plots. And we also compared measurements data between the RTSST and that of flat type using several automobiles. 4 refs., 8 figs., 4 tabs.

  20. Development of refrigerator insulation with reduced CFC-11. Reizokoyo flon sakugen uretan dannetsuzai no kaihatsu

    Kai, H.; Fukuda, K.; Yoshioka, M. (Sharp Corp., Osaka (Japan))

    1992-11-10

    Polyurethane thermal insulator in which the usage of CFC-11 is 50% reduced by increasing the percentage of water has been developed for the purpose of reducing polyurethane-foaming CFC-11 used as thermal insulator of refrigerators. In this new water-intensive feedstock system, the overall OH-value in polyol was lowered; the usage of aromatic amines was curtailed; and the amount of sorbits was increased so as to secure adhesiveness at the foaming jig temperature of 35[degree]C. As for the improvement of fluidity, a combination of four kinds of polyols offered viscosity in the same level as in the conventional ones. Thermal conductivity was worsened, but the rate of its drop could be controlled below 3% by some measures such as homogenization of stock materials, choice of a suface-active agent which makes foam bubbles minute, etc. Concerning curing property which has a large effect on productivity, a reaction type amine-based catalyst delaying thickening behaviour at the time of foaming was selected and a gelling promotive tertiary amine-based catalyst which can develop foam curing promptly was combinedly used to reduce curing property from five minutes in the past to four minutes. 2 refs., 6 figs., 14 tabs.

  1. Development of practical solar-electric vehicle; Jitsuyo fukyugata solar denki jidosha no kaihatsu

    Saito, S; Fujinaka, M [Tokyo Denki University, Tokyo (Japan)

    1997-11-25

    The paper reported on a Tokyo-Nagoya travel test on a practical spread type solar-electric vehicle, Solar-EV. A comparative study was made running the same type gasoline vehicle, GV. The measured power consumption amount of Solar-EV is 57.6 kWh. By converting it into Mcal unit, an energy consumption amount of 49.5 Mcal was obtained. Further, as to GV, the energy consumption amount of 316 Mcal was obtained using the amount of supply of gasoline (mean heating value: 8.4 Mcal/h) of 37.6 l and the fuel consumption of 16.2 km/l. Accordingly, the energy consumption amount of Solar-EV became a sixth of that of GV. In the cost comparison, the cost of Solar-EV was 1,440 yen (power source price: 25 yen/kWh), which is about a third of that of GV, 3760 yen (gasoline unit price: 100 yen/l). Monocrystal Si solar cells, 270W, installed on hood/roof are connected to the main 288V system (the auxiliary 12V system is amorphous Si), and generate power 4.4 kWh during travel. A total power consumption amount of Solar-EV in the total travel (Tokyo-Nagoya) is 79.9 kWh including the auxiliary system, approximately 6% of which was to be supplied from solar cells. 1 ref., 6 figs., 3 tabs.

  2. Development of solar power generator system; Taiyoko netsufukugo hatsuden system no kaihatsu

    Kisara, K; Kumagai, T; Niino, M; Chen, L; Eguchi, K [National Aerospace Laboratory, Tokyo (Japan)

    1997-11-25

    Described herein is a new hybrid solar power generator system, in which solar energy is separated into the light and heat components by a wavelength-selective filter before being directly converted into electric power, the former for the amorphous solar cell (ASC) unit and the latter for the thermoelectric unit. These units complement with each other to enhance overall efficiency. The ASC unit should have a higher efficiency when it works on the light component, because the heat (infrared) component increases cell temperature and decreases its output. For the ASC unit, the effects of the filter have been tested. The thermoelectric unit, generating power by the Seebeck effect, should have a higher efficiency, if heat flux passing through the unit can be increased, because of increased temperature differential, to which voltage produced increases proportionally. For the thermoelectric unit, heat is collected by a parabolic mirror unit from sunbeams received by a heliostat. Characteristics of these units are grasped almost as expected by the tests. 4 refs., 11 figs., 1 tab.

  3. Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

    Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-03-01

    The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

  4. Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

    Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

  5. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  6. Development of pressurized internally circulating fluidized bed combustion technology; Kaatsu naibu junkan ryudosho boiler no kaihatsu

    Ishihara, I [Center for Coal Utilization, Japan, Tokyo (Japan); Nagato, S; Toyoda, S [Ebara Corp., Tokyo (Japan)

    1996-09-01

    The paper introduced support research on element technology needed for the design of hot models of the pressurized internally circulating fluidized bed combustion boiler in fiscal 1995 and specifications for testing facilities of 4MWt hot models after finishing the basic plan. The support research was conduced as follows: (a) In the test for analysis of cold model fluidization, it was confirmed that each characteristic value of hot models is higher than the target value. Further, calculation parameters required for computer simulation were measured and data on the design of air diffusion nozzle for 1 chamber wind box were sampled. (b) In the CWP conveyance characteristic survey, it was confirmed that it is possible to produce CWP having favorable properties. It was also confirmed that favorable conveyability can be maintained even if the piping size was reduced down to 25A. (c) In the gas pressure reducing test, basic data required for the design of gas pressure reducing equipment were sampled. Specifications for the fluidized bed combustion boiler of hot models are as follows: evaporation amount: 3070kg/h, steam pressure: 1.77MPa, fuel supply amount: 600kg-coal/h, boiler body: cylinder shape water tube internally circulating fluidized bed combustion boiler. 4 refs., 4 figs.

  7. Development of a robot system for converter relining; Tenro chikuro robot system no kaihatsu

    Ito, Y; Kurahashi, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1995-09-12

    In steelmaking plants, the relining work of converters requires plenty of manpower and time. Recently, the number of expert brick workers has decreased, and it has been difficult to get together the necessary number of workers for the converter relining. To solve these problems, a robot system has been developed and realized for the converter relining. The system consists of two intelligent robots and an automatic brick conveying machine. With visual function and flexibly controlled hands, the robot enables to heap up bricks in the same manner as expert workers do. The automatic brick conveying machine consists of roller conveyers and a cage lifter that convey bricks on palettes to the suitable position for the robot to easily handle. This robot system has enabled to save much labor for the converter relining. 8 figs.

  8. Development of a downhole seismic source with controlled waveform; Hakei seigyogata kochu shingen no kaihatsu

    Kuroda, T; Ikawa, T [Japex Jeoscience Institute, Tokyo (Japan); Sato, T [Meiho Engineering Co. Ltd., Tokyo (Japan); Kakuma, H [Akashi Corp., Tokyo (Japan); Onuma, H [Engineering Advancement Association of Japan, Tokyo (Japan)

    1997-05-27

    A downhole seismic source which can output continuous waves having arbitrary waveforms was developed. The development was targeted to make tomographic exploration purposed to evaluate geological properties of a ground bed before and after constructing a building in a ground several hundred meters deep from the ground surface. The source is considered to be used in an environment consisting of soft rocks or more robust rocks and having no casing. It can be used in a well hole having a diameter of 100 mm, is capable of measuring P and S waves in a distance between well holes of up to 100 m, can be used at a depth of up to 500 m, and can output waveforms having seismic source spectra of up to 1000 Hz. An oscillation actuator using laminated piezo-electric elements was used for the oscillation element. The seismic source consists of a hydraulic device to clamp the equipment onto hole walls, piezo-electric elements as the oscillation element, and an inertia weight for applying vibration from above and below. To make an oscillation, the main body is first clamped on the hole wall. For horizontal oscillation, the piezo-electric elements contained in a clamping device provide the horizontal oscillation. For vertical oscillation, the piezo-electric elements placed below the main body oscillates the inertia weight. The initially targeted specifications have been achieved. 3 refs., 4 figs., 1 tab.

  9. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  10. PV glass curtain walls; Kenzai ittaigata taiyo denchi gaiheki no kaihatsu (glass curtain wall eno tekiyo)

    Yoshida, T.; Iwai, T.; Ouchi, T.; Ito, T.; Nagai, T.; Shu, I. [Kajima Corp., Tokyo (Japan); Arai, T. [Showa Shell Sekiyu K.K., Tokyo (Japan); Ishikawa, N.; Tazawa, K.

    1997-12-20

    Reported in this article are PV (photovoltaic) modules now under development for integration into building walls. First of all, the power generating capability of PV modules and appropriate use of the generated power are studied, and the performance (resistance to fire or incombustibility, strength and durability, appearance and design, and dimensional standardization) that such outer wall materials are to be equipped with are determined. Next, module development, installation technique, computer graphics-aided facade designing, and real size module-using proof test are studied before installability, the power to be generated, and designs are finalized. In the development of modules, design evaluation involves the combining of various kinds of glass, solar cells, back sheets, and fillers, and the importance is confirmed of the prevention of insulation degradation around the modules. As for the methods of installation, the gasket method and aluminum sash method, etc., are tested. In the study of facade design, it is found that various expressions are possible by properly choosing gasket colors, module types, and kinds of glass to cover the openings. 1 ref., 6 figs., 3 tabs.

  11. FY 2000 report on the results of the regional consortium R and D project - Regional new technology creation R and D. First year report. R and D of medicine toxicity assessment use hepatocyte chip; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium kenkyu kaihatsu / chiiki shingijutsu soshutsu kenkyu kaihatsu. Dokubutsu dokusei hyokayo kansaibo chip no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    NONE

    2001-03-01

    Judging that in the beginning of the toxicity test, the necessary information/knowledge are acquired not by using animal itself but only by using liver system (hepatocyte), the development was proceeded with of the hepatocyte chip substituting for the animal experiment. Studies were made in the following five fields: 1) design of functional matrices; 2) development of the pharmacological assessment technology; 3) development of cell sensing technology/biosensor fabrication; 4) study of a possibility and the limit of cell patterning technology; 5) survey of the market scale. In 1), studies were made of the establishment of the 3D culture method for hepatocyte and the construction of hepatocyte models for medicine assessment using pieces of liver. In the latter, by including capsule using the sugar introduced with galactose residue which is special sugar of hepatocyte to alginic acid and chitosan which are natural polymer and also hepatocyte isolated into sponge, aggregate was formed, and its use as a medicine assessment use liver model was tried to be made. (NEDO)

  12. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  13. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  14. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  15. Development of Fresnel lens for improvement of rear visibility; Shikai kojo Fresnel lens no kaihatsu

    Iwamoto, K; Sanada, C; Tsukino, M [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Fresnel lenses have been widely used to increase the visual field around vehicles for drivers. However, internal reflection in these lenses has been an obstacle in producing dear images. This internal glow is generated by incident light from an unexpected direction reflecting on the non-lens surface or radiating from the non-lens surface of the Fresnel lens. The cause of internal glow has been made dear combining louver film with the lens. The newly developed technology removes obstacles in producing dear images by reducing internal glow. 7 figs.

  16. Development of film antenna for diversity reception; Diversity taio film antenna no kaihatsu

    Shigeta, K; Taniguchi, T; Kubota, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    Based on the principle of capacitance-loaded window antennas, a new film antenna construction pasting an antenna element on a defogger element printed on a rear window was found. The film antennas show high reception performance, and can be used as television diversity antennas or a VICS-FM multiplex antenna. This paper describes the antenna design concept, the antenna construction and the application to a recreational vehicle which styling is 1.3-Box wagon for the electric accessory. 2 refs., 11 figs.

  17. Development of lane change aid system; Lane change aid system no kaihatsu

    Uemura, H; Yoshida, T; Butsuen, T [Mazda Motor Corp., Hiroshima (Japan); Sakai, N; Nakano, T; Nakamoto, T

    1997-10-01

    We have developed a lane change aid system, which detects vehicles behind in adjacent lanes with CCD images, shows the driver the information of vehicle location with a head-up display, and warns him/her if necessary. By comparing the brightness on two CCD images, distance distribution along several CCD lines is measured. To assure the effective vehicle detection on public roads, we have developed a detection algorithm which distinguishes vehicles and guard-rails by observing the patterns of measured distances. We will show the system configuration, detection logic, and the system evaluation on public road. 5 refs., 12 figs.

  18. Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

    Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

  19. Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

    NONE

    2000-03-01

    Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

  20. Development of mechanical shield docking method; MSD (mekanikaru/shirudo/dokkingu) koho no kaihatsu

    Yokota, I. [Tokyo Metroplitan Government Water Supply Bureau, Tokyo (Japan); Watanabe, T.; Hagiwara, H. [Shimizu Corp., Tokyo (Japan); Nishitake, S. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Endo, M. [Obayashi Corp., Osaka (Japan)

    1993-09-20

    For the construction works of underground tunnels, mainly the shield method has so far been adopted, but in order to make underground junction of shield machines, the method of utilizing a shaft or the method of improving the earth by the auxiliary methods such as chemical feeding have been adopted. However, either method has restriction for its practical application. The MSD method uses no auxiliary method at all, can join directly two shield machines mechanically underground, has high water stoppability at its junction, is applicable for either of shield machines of slush type or mud pressure type, and is the method to solve totally various problems in the existing joining methods. This method is the one that two shield machines, one on the out-pushing side and another on the in-receiving side, progress from both sides and face each other, then the both are joined mechanically for unification by pushing a steel penetration ring built-in the out-pushing shield machine to the rubber ring built-in the penetration chamber of the in-receiving shield machine. After joining, the shield machines are disassembled for removal leaving the junction only, and the secondary lining is done with concrete. 6 figs.

  1. Development of remote controlled blasting system for tunnels; Tunnel yo enkaku seigyo happa system no kaihatsu

    Suzuki, S.; Kawamura, M.; Hirosaki, Y. [NOF Corp., Aichi (Japan)

    1997-06-30

    A downsized wireless blasting system has been developed for tunnel construction in the mountainous districts. This system consists of an oscillator, loop antenna, and initiator. The ac magnetic field is generated in the loop antenna using 550 Hz ac generated by the oscillator, to induce the electro motive force between both ends of receiver coil in the initiator. It is stored in the capacitor after rectification, to initiate the detonator by discharging with the firing signal. This system has been developed by downsizing the conventional RCB (remote controlled blasting system) for underwater blasting, and unmanned operation is planned in future. An oscillation frequency, 550 Hz with an actual result has been adopted. The arm length of loop antenna is 3 m, which can be installed in the tunnel. Various receiver initiators were fabricated as a trial. A convex type was adopted due to its excellent receiving performance. The receiving performance was improved by increasing the magnetic induction and decreasing the power loss. After receiving voltage of the receiver initiator was confirmed, field initiation tests were conducted. Initiating and blasting were successfully carried out. 5 refs., 15 figs., 3 tabs.

  2. Power conditioner without isolation transformer; Toransuresu power conditioner no shohin kaihatsu

    Okado, C; Itami, T; Kimoto, K [Toshiba Corp., Tokyo (Japan)

    1996-10-27

    A light-weight downsized and high efficiency transformer-less type 4 kW power conditioner (inverter) has been developed. This power conditioner insures the system interconnection protection by monitoring the voltage of two single-phase three-line circuits. The power conditioner has weight of 17.5 kg and efficiency of 94%. Potential fluctuation of photovoltaic cells due to the switching of power devices at the inverter was reduced. Output capacity was reduced in the low input voltage range. Outflow of DC component was prevented in high accuracy by usually correcting the zero point drift of detector, and by using the current detector with excellent linearity. To detect the DC ground fault, and to trip the output side breaker locating at the ground fault current pass, a zero phase converter detection circuit has been developed, by which the DC component can be detected at the DC input side. As a result of performance verification, the efficiency, power factor, EMI level, protection of outflow of DC component, protection of ground fault, protection of single operation detection, and noise level were satisfied. This system is prospective for the diffusion of photovoltaic power generation in the future. 3 refs., 8 figs., 1 tab.

  3. FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    NONE

    1999-03-01

    Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

  4. Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    NONE

    1997-12-01

    In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

  5. Synthesis of new erodable polymers response to environmental stimuli; Atarashii kankyo chowagata bunkaisei plastic no kaihatsu

    Kato, M; Nagasaki, Y [Science University of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1997-02-01

    This report relates to the designing of functional materials that decompose in response to various signals. A derivative of {alpha}-bromomethylstyrene is caused to act on the living anions of {alpha}-methylstyrene for the synthesis of a pyrolytic polymer having unsaturated groups at its terminals. The terminal double combinations of this polymer split under the influence of heat, acid, or base for depolymerization which is quantative, and the decomposition temperature may be controlled by replacing terminal phenylallylic groups with methyl groups or phloro-groups. Furthermore, a novel polythyramine polymer is synthesized with its principal chain constituted of NCH2CH2Si, the principal chain easy to disintegrate when exposed to an electron beam. The polymer is signal-responsive and may be patterned by use of an electron beam. As a temperature-responsive polymer with the hydrolytic feature controlled, poly(thyroxy ethylene glycol) is obtained from a derivative of diaminosiloxane and oligo-oxyethylene. This is a high-mobility, temperature-responsive material whose hydrolysis may be controlled. 3 refs., 2 figs.

  6. Development of practical diet for aquaculture of Japanese flounder; Gyofun wo sakutenshita hirameyo shiryo no kaihatsu

    Kikuchi, K.; Furuta, T.

    2000-07-01

    Feeding experiments were conducted to examine the potential use of defatted soybean meal (SBM) in combinations with blood meal (BM), corn gluten meal (CGM) and freeze dried meat of blue mussel (BMM) as a partial replacement of fish meal (FM) in the diet of Japanese flounder. Availability of CGM in combinations with BM and/or BMM was also examined. Juvenile fish of about 4 g in initial body weight were fed diets to satiation twice daily, 6 days per week for 8 weeks at 20 degree C in both feeding experiments. Weight gain of fish fed diet replacing 45% FM protein with SBM was not different from that of fish fed the control diet containing FM as a protein source, however, feed efficiency (FE) in fish fed the SBM diet was significantly lower. Growth and feed performance of fish fed diet replacing 45% FM protein with SBM and BM were comparable to those of fish the control diet. Inclusion of 5% BMM for equal amount of SBM in the SBM-BM diet improved the growth and FE of the flounder remarkably and both values were significantly higher than those in the control. Replacing 55% of FM protein with SBM and CGM or SBM and BM resulted in poor growth performance. There were not marked differences in hematological characteristics together with proximate composition of the whole body of cultured fish fed the dietary treatments. Weight gain and FE of fish fed diet replacing 40% FM protein with CGM were inferior to those of fish fed the control diet containing FM as a protein source. Replacement of 40% FM protein with CGM and BM made those parameters worse. Inclusion of BMM in CGM-BM diet did not improve the growth of fish. Adverse effects of replacing FM protein with CGM and/or CGM and BM were stronger with increasing replacement level. These results indicate that SBM is highly available as alternative protein source for fish meal in the diet of Japanese flounder. SBM in combination with BM successfully replace about 45% of FM protein in the diet without supplemental amino acids. Furthermore, it is suggested that more replacement can be attained with inclusion of 5% BMM in the SBM diet. CGM is not considered to be useful ingredient on practical bases. (author)

  7. Jet engine R and D and I; Watashi to jet engine kenkyu kaihatsu

    Murashima, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-06-10

    My efforts towards at the development of aeroengines since the end of the war are described. The J3-7 engine propelled the T1 trainer plane, and was installed as booster aboard the P2J antisubmarine patrol aircraft. It was the first jet engine that Japan produced after the end of the war, and had been in use until quite recently. I took part in the construction of a prototype of the JR100 series designed to serve as VTOL (vertical take-off and landing) aircraft lift engines, and in the test thereof. As the shift from turbojet to turbofan proceeded, I participated in the development of the FJR710 engine under the guidance of National Aerospace Laboratory, and the product was installed aboard an experimental STOL (short take-off and landing) aircraft Asuka. I next joined a Defense Agency initiative for a reheat turbofan to replace the J3 aboard trainer plane, and the result was the low bypass ratio/high output F3 engine. In 1989, Ministry of International Trade and Industry decided for a large-scale project of developing an engine for a next-generation supersonic transport, and the HYPR (Super/Hypersonic Transport Propulsion System) project was started. The project was participated in by manufacturers from overseas, which were GE, P and W, RR, and SNECMA. The foreign corporations worked on an equal footing with the Japanese parties, and collaboration between the participants was smooth, with each party endeavoring in the field they were good at. The project will be concluded as scheduled in fiscal 1998. (NEDO)

  8. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  9. Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

    Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1997-07-10

    The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

  10. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  11. Current status and future of space development; Uchu kaihatsu no genjo to shorai

    Matokawa, Y. [Institute of the Space and Astronautical Science, Tokyo (Japan)

    1998-05-01

    Space development has an aspect of contributing to livelihoods. Various types of satellites, such as those for weather forecasting, TV broadcasting, international communication (telephone and internet systems), and GPS-aided car navigation, have been already launched. Space science of the 20th century roughly tells the history of some 15 billion years from the big bang to birth of mankind as a spectacular story. The international space station, construction of which is to be started in 1998, should drastically enlarge man`s experiences in the universe. The space activity plans for the future draw various dreams, such as spaceplane, lunar base, solar generator satellite, Mars base, space colony, skyhook, and so on. Dreams of mankind have been eventually realized in the past history. It is time to deliberately assess what are meant by the space development of the 20th century, and to review ideal directions of the space development for the next 100 or 1000 years. 6 figs.

  12. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  13. NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

    NONE

    2000-09-01

    This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

  14. Development of ultra-low pressure reverse osmosis membranes; Choteiatsu gyakushintomaku no kaihatsu

    Hirose, M.; Ito, H.; Ohara, T. [Nitto Denko Corp., Osaka (Japan)

    1998-06-05

    Described herein is development of ultra-low pressure reverse osmosis (RO) membranes. The composite RO membrane, which is now widely used, has a cross-sectional structure consisting of an ultrafilter membrane as the support and a very thin skin layer responsible for filtration. It is confirmed that the skin layer is of a pleated structure. Growing this structure can greatly accelerate permeation of water without damaging arresting and durability characteristics of the membrane, and hence is a desired approach. Utilization of molecular structure simulation of the skin layer materials is investigated by the molecular dynamics. The results show that the stable structure of the material for the skin layer in the RO membrane is a network structure with regularly arranged honeycombs, when it should arrest at least 99% of salt. These techniques serve as the bases for development of the ultra-low pressure RO membranes (ES Series), where the skin layer is made of cross-linked, totally aromatic polyamide. The membrane passes twice as large a quantity of water as the conventional one, is highly resistant to chemicals, and arrests 99.7% of salt. 3 refs., 4 figs.

  15. CAE for the development of two-wheeled vehicles. Nirinsha kaihatsu no tame no CAE

    Hirose, T. (Suzuki Motor Co. Ltd., Shizuoka (Japan))

    1992-11-01

    Applications of CAE to the development of two-wheeled vehicles were outlined. The performance estimation program for 4-cycle engines featured by its easy execution was presented illustrating an estimation model and estimated results, and the FEM generator for strength/rigidity analysis CAE indicating analytical examples of a piston and frame which is featured by easy formation of models and easy execution of advanced analyses by beginners. The vibration analysis system to estimate exciting forces from engine specifications and to estimate vibration levels of bodies with FEM models was also presented together with the estimation system of rider's vibration sensitivity. Furthermore, the noise suppression/ exhaust pressure calculation program to support muffler designs by simultaneous calculation was presented together with the thermal flow analysis program featured by easy calculation with more suitable models illustrating the analytical example of thermal flow in a large luggage box. 7 refs., 15 figs.

  16. Development of lowdrag aerodynamically stable with indented processing; Indento kako wo hodokoshita seishin keburu no kaihatsu

    Hojo, T.; Yamazaki, S.; Okada, H.

    1998-10-29

    A wind-resistant design of cables for large cable-stayed bridges is required as a measure against rain-wind induced vibration. In such bridges, many cables are arranged in a short pitch, which causes a large drag force on the cables. Therefore, reduction of drag force on cables is essential for rationalizing bridge design, as well as restraint of vibration. This paper describes studies on a new cable having both a low drag co-efficient force and rain-vibration suppressing effects. Through many investigations using wind tunnel tests, an indented cable was developed as a countermeasure against rain-wind induced vibration, and finally it was applied to the Tatara Bridge which is the largest cable-stayed bridge in the world. (author)

  17. Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

    Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-10-15

    Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

  18. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Data book); 1974 nendo suiso no seisei yuso chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Shiryohen

    NONE

    1975-05-30

    The paper studied separately some items which become pre-conditions or periphery conditions for study work included in the report work of a system to refine/transport/store hydrogen and the safety technology. Those were arranged as data in the form of figure/tables. The data as literature related to the hydrogen energy system were also arranged. Included in these are a concept of so-called hydrogen economy system, ideas for end users and technology development, etc. The safety problem was also arranged in the form of characteristics of hydrogen and the comparison with other systems. As to the hydrogen production, the paper outlined primary energy sources and included the outline of hydrogen production technology. It also centered on the hydrogen refining/storage/transport system and made a list of research institutes, researchers, details of study, main related study, main topics, etc. The data are those about energy related data, features and safety of hydrogen energy system, various examples of the concept of hydrogen energy system, concept and development of end user use technology, production of hydrogen, etc. (NEDO)

  19. Formation of fine aggregate structure by solid-state displacement reaction of Ti with CoO or NiO. CoO oyobi NiO to Ti kan no koso chikan hanno ni yoru bisai fukugo soshiki no seisei

    Taimatsu, H; Kaneko, H [Akita Univ., Akita (Japan). Mining College; Wada, K [Akita Univ., Akita (Japan). Graduate School

    1992-09-20

    As a result of search for systems which have aggregate structures, the displacement reaction products of Ti with CoO or NiO are found to have aggregate structures in which the produced oxides and metals are entangled with each other. The displacement reaction of Ti with CoO or NiO is investigated at the temperature of 1273K. In the reaction of either couple, aggregate products are produced, and reacted layer is observed in the TiO2 matrix wherein Co or Ni phases are three dimensionally entangled in finely dispersed state of micron order. 2 layers of cavitated and dense TiO2 layers are found in the reacted layer. The thicknesses of the reacted layer are not constant according to locations, but thick portions are grown obeying the parabolic rate law. As a result of the study on the possibility of fabricating cermet by the reaction between powders, finely mixed characteristic structures are found to be easily obtained using systems which can produce aggregate structures. 24 refs., 9 figs.

  20. FY 2000 report on the basic survey to promote Joint Implementation, etc. Survey of the effective use of wastes at palm oil refineries; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Palm oil seisei kojo ni okeru haikibutsu yuko riyo chosa

    NONE

    2001-03-01

    As to empty fruit bunches (EFB) which are wasted at the Lahad Datu plant of Felda Vegetable Oil Products Co. in Malaysia, a project was studied for energy substitution and greenhouse effect gas reduction by fluidized bed cogeneration facilities using this as fuel. In the project, studied was the introduction of on-site cogenerator of 7,800kW in generating-end output, and that of IPP cogenerator of 16,000kW as reference. As a result of the study, the energy substitution amount in toe in 20 years was approximately 376 k tons in case of on-site power generation/fluidized bed boiler and approximately 695 k tons in case of IPP and fluidized bed boiler. The amount of greenhouse effect gas emission in toe in 20 years was approximately 5,757 k tons and 11,654 k tons, respectively. Concerning the profitability, the internal earning rate was 3.32-8.47% in case of on-site power generation/fluidized bed boiler and 9.13-14.65% in case of IPP/fluidized bed boiler. It indicated the materialization of the project. (NEDO)

  1. Relationship between concentration of surfactant and pressure for droplet creation, and effect on droplet size in microchannel O/W emulsification; Maikurochaneru ni yoru O/W nyukaho ni okeru kaimen kasseizai nodo to ekiteki seisei atsuryoku no kankei, oyobi koreraga ekitekikei ni oyobosu eikyo

    Kawakatsu, T.; Komori, H.; Oda, N.; Yonemoto, T. [Tohoku Univ., Sendai (Japan). Graduate School of Engineering

    1998-03-01

    O/W (oil in water) emulsion is produced by micro-channel emulsification method, and the effects of surfactant concentration on the pressures at which droplet generation starts and stops are evaluated in connection with the water phase and oil phase interfacial tension. In addition, the effects of surfactant concentration and operational pressure on the droplet size are investigated by measuring the generated droplet distribution, mean droplet size, standard deviation, geometrical standard deviation, and the possibility of producing mono-dispersion emulsion whose droplet size is large than 10 micron. The breakthrough pressure and the minimum pressure for droplet generation become low with the increase of SDS (sodium lauryl sulfate) concentration. The surfactant concentration, however, is found to have no effect on the breakthrough pressure and the minimum pressure for droplet generation when the SDS concentration exceeds the critical micelle concentration. It is true also for a system added with NaCl. As regards droplet size, uniform 20{mu}m droplet is obtained irrespective of the surfactant concentration and pressure. 13 refs., 10 figs., 2 tabs.

  2. Structure and coke preventing characteristics of Ca-Ni-Mo/Al sub 2 O sub 3 catalyst for hydrogenation of brown coal liquid bottoms. Kattan ekikaabura suisokayo Ca-Ni-Mo/Al sub 2 O sub 3 shokubai no kozo to tansoshitsu seisei yokusei sayo

    Kimura, T. (Cosmo Oil Co. Ltd., Tokyo (Japan)); Kaneko, T.; Kageyama, Y. (Mitsubishi Kasei Corp., Tokyo (Japan). Research Center); Kawai, S. (Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan))

    1990-09-01

    Operating a 50 t/d fixed bed pilot plant, hydroprocessing of de-ashed coal liquid bottoms (DAO) derived from Victorial Brown coal liquefaction has been carried out in Australia using a newly developed Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. This catalyst has a great advantage compared with conventional molybdenum catalysts in that there is less coke formation using this catalyst as indicated by 5,000 h runs in a 0.1 t/d bench scale plant. In this paper, the catalyst active center and the role of Ca in the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst were analyzed using Raman, TPS-XPS, EXAFS and AES methods. Molybdenum is loaded as CaMoO {sub 4} and X-ray diffraction data. But the oxide is changed to MoS {sub 2} after sulfiding treatment. Data of the Mo-S bond obtained from EXAFS analysis indicated that MoS {sub 2} has a tendency to pile up on the Ca-Ni-Mo/Al {sub 2} O {sub 3} catalyst. 20 refs., 12 figs., 5 tabs.

  3. Determination of standard Ghibbs free energy of formation of NiW sub 2 B sub 2 and activity of Ni-W binary system by EMF measurement. Kidenryokuho ni yoru NiW sub 2 B sub 2 no hyojun seisei Gibbs jiyu energy to Ni-W 2 seibunkei no katsuryo no sokutei

    Kayama, Koichiro; Hashimoto, Yasuhiko; Suzuki, Kenji; Matsuo, Hideki (Himeji Inst. of Tech., Hyogo (Japan) Fukushin Electric Co., Ltd., Hyogo (Japan))

    1989-12-25

    NiW {sub 2} B {sub 2} (M phase), existing in trinary Ni-W-B system, was measured in standard Gibbs free energy (GF) of formation in the temperature range from 1273K to 1423K by an electromotive force method (EMF) with use of solid oxide electrolyte. First, oxide phase in equilibrium with three-phase M-W-Ni solid solution region was confirmed to be B {sub 2} O {sub 3}. Binary Ni-W system solid solution in equilibrium with M phase and W phase is constant in composition with Ni-16.4mo1%W in the above temperature range. WO {sub 2} and WO {sub 2.72} were actually measured in GF. As Ni-W solid solution is in equilibrium with WO {sub 2} and WO {sub 2.72}, binary Ni-W system was measured in activity by the EMF, and Ni-16.4mo1%W solid solution was calculated in GF of mixing by use of the above measured GF of WO {sub 2} and WO {sub 2.72}. Finally with use of sample in M-W-Ni solid solution region, M phase was calculated in GF by the EMF. The result of those calculations were expressed with experimental formulas. 19 refs., 10 figs., 3 tabs.

  4. Acceleration effect of alcohols on ion association of molbdophosphate with malachite green and its use to the sensitive flow-injection determination of phosphate. Molybdo rinsan ion-malachite green ion kaigotai seisei ni oyobosu alcohol no hanno sokushinkoka to sore wo riyosuru rin no kokando flow injection bunseki

    Motomizu, S; Yasuda, Y; Oshima, M [Okayama Univ., Okayama (Japan). Faculty of Science

    1991-12-10

    Molibdophosphoric acid (PMo) reacts with malachite green (MG{sup +}) to form a colored ion associate (MG{sup +}- PMo) in an acidic solution according to the formula : HMG{sup 2+}+H{sub 3}PMo{sub 12}O{sub 40}{yields}(MG{sup +})H{sub 2}PMo{sub 12}O{sub 40}+2H{sup +}. A protonated form HMG{sup 2+} is yellow (the absorption mximum at 446 nm), whereas the ion associate MG{sup +} is blue green (the absorption maximum at 650 nm). MG{sup +} is found to accelerate the formation of PMo. Water-miscible organic solvents such as methanol,ethanol and propanol also accelerate the formation of PMo as well as the formation of MG sup + - PMo. Some anionic surfactants decelerate the reaction, however, contribute to the suppression of the baseline drift in a flow injection analysis (FIA). By the use of the proposed reaction accelerator and surfactant. a highly sensitive FIA system is established for,orthophosphate up to the range of several ppb. 16 figs.. 11 refs.

  5. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Summary); 1974 nendo suiso no seisei yuso chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Yoyakuban

    NONE

    1975-05-30

    This study aims at the following. As to an alternative plan of the hydrogen distribution system, this paper makes the comprehensive evaluation from viewpoints of possibility, adaptability to society, economical efficiency, reliability, dynamic characteristics, etc., selects the most rational system and picked up the problems for realization of the system. It also sets up standards for safety technology relating to the hydrogen energy system and acquires the basic knowledge/information on concrete disaster prevention technology which backs up the standards. Among those, in this fiscal year, as system analysis of the hydrogen distribution system, study was made on system analysis of the system alternative plan and problems on system realization. Next, as an investigational study on safety technology in hydrogen energy system, the paper conducted the survey/collection in Japan and abroad of the present law, standards for handling, and examples of disaster/accident in relation to hydrogen, and the survey research on the concrete safety problem predicted. The paper studied the technology related to the safety problem required for safety. Industrial Research Institute, Japan, and the four companies under re-consignment made each report in which the results of the research were detailedly arranged. This paper is a summary of these reports. (NEDO)

  6. Report on coal refining and chemical equipment analogous to coal liquefaction equipment in fiscal 1981. Maintenance of equipment for direct desulfurization, indirect desulfurization, and fluidized catalytic cracking; 1981 nendo sekitan ekika ruiji seiyu seisei oyobi kagaku sochi ni kansuru chosa hokokusho. Chokudatsu, kandatsu, ryudo sesshoku bunkai sochi no hozen

    NONE

    1981-07-01

    This questionnaire survey was intended to investigate the actual state of maintenance such as materials used, conditions for use, anti-corrosion measures, and cases and handling of damage, concerning primary apparatus in the direct/indirect desulfurization equipment and the fluidized catalytic crackers, which are owned by each oil refinery and which are analogous to coal liquefaction equipment. The questionnaire was intended for the following equipment and apparatus, with the actual state of their maintenance investigated. 1. Questionnaire concerning maintenance of direct desulfurization (reactor, high temperature separation tank, material furnace tube, reactor exit piping, high temperature heat exchanger, low temperature heat exchanger, and pressure reducing valve), 2. Questionnaire concerning maintenance of indirect desulfurization (reactor, high temperature separation tank, material furnace tube, reactor exit piping, high temperature heat exchanger, low temperature heat exchanger, and pressure reducing valve), 3. Questionnaire concerning maintenance of fluidized catalytic cracker (reactor, regeneration tower, riser pipe, and fractionator bottom pump). The questionnaire this time was distributed to 27 domestic oil companies, with the reply received from 23 of them. The replies were summarized by each type of equipment. Shown at the back of the report were the cases of damage and handling in FCC's and reactors. (NEDO)

  7. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Investigational study of behavior of trace impurities in the liquefaction process); 1974 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Ekika katei ni okeru biryo fujunbutsu no kyodo ni kansuru chosa kenkyu

    NONE

    1975-05-28

    Hydrogen gas as material is produced mostly by steam reforming of hydrocarbons, and includes a considerable amount of impurities such as carbon dioxide, nitrogen and oxygen. The concentration of impurities in the refined gas is approximately 1ppm. In the liquefaction process of hydrogen liquefaction plant, the gases entering the low temperature portion near the free expansion valve (J-T valve) are mostly oxygen and nitrogen. When oxygen is solidified, attached, accumulated near J-T valve, it incurs a possibility of exploding for reason of impact force, etc. by contact with the valve portion. A mixture of hydrogen and oxygen ignites at the minimum value of approximately 0.02 milli-joule, and therefore it has great danger of explosion. As viewed from a point of danger prevention, there is a possibility of explosion when the hydrogen-oxidizing agent mixture is formed. Accordingly, it is necessary to conduct an experiment for confirming the explosion at J-T valve portion. From viewpoints of prevention of explosion accident and running operation, it is necessary to experimentally grasp the definite allowable oxygen concentration. Further, it is necessary to establish a technology to continuously and accurately measure the concentration of trace impurities in hydrogen gas. (NEDO)

  8. Preparation of spherical fine particulate pigments within water-in-oil emulsions and their properties. (II). ; Formation mechanism and characteristic of spherical fine particulate pigment of tartrazine. W/O emulsion wo mochiita kyujo biryushi ganryo no chosei to seishitsu(dai 2 ho). ; Kiiro 4 go kyujo biryushi ganryo no seisei kiko to tokusei

    Imai, T.; Iwano, K.; Hotta, H.; Takano, S.; Tsutsumi, H. (Kao Corporation, Tokyo (Japan))

    1991-12-20

    The previous report explained that an excellent spherical particulate pigment with a grain size of 0.5 mm or less can be obtained by preparing multinuclear aluminum lakes from acidic dyes and multinuclear aluminum salt using water droplets in a W/O emulsion as reaction fields. This paper describes preparing pigments varying the charging concentrations of the pigments in a W/O emulsion and the droplet particle size to discuss the mechanism of forming the pigments. As a result, it was found that the particle sizes in the produced pigments have a clear correlation with the charging concentrations of the pigments and the droplet particle sizes in the W/O emulsion. A pigment produced in the W/O emulsion forms only in its own droplets, and reflects its particle sizes. Films dispersed with pigments having different particle sizes were prepared to discuss their tinting abilities, whereas it was clarified that the smaller the particle size, the higher the tinting ability and the higher saturation in colored paint films. 6 refs., 9 figs., 3 tabs.

  9. Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

    NONE

    1997-03-01

    This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

  10. FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

    NONE

    1981-03-01

    A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

  11. Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

    NONE

    1991-05-01

    Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

  12. R and D project for large industrial technologies in fiscal 1989. Report on achievements in R and D of robots for critical works; 1989 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

    NONE

    1990-03-01

    Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1989. In the R and D of sensor technologies, a prototype tri-axial one-millimeter sensor array and a signal processing device were produced and evaluations were given. A prototype production and evaluations were made on a system that can recognize comprehensively the slip, hardness, and moment as the tri-axial tactile information. In the R and D of motive force technologies, discussions were given on improvement of sensitivity of the torque sensor in the actuator for force control. Design and prototype fabrication were carried out on a speed reducer integrated actuator having a torque sensor for the manipulator's elbow joint. In addition, a force controlled controller was fabricated on a trial basis, which compensates the non-linearity of the force controlled actuator by means of software control. In the R and D of the robot languages, an application program was prepared on a representative work related to movements of a critical work robot. Verification was also conducted on the reasonability of the grammar specifications. (NEDO)

  13. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'Taikankyo kyoka soshi'. Dainiki kenkyu kaihatsu hyoka

    NONE

    1986-03-31

    In the research and development of the environment resistance strengthened elements with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments, the second term has developed an integration technology and its evaluation technology based on the achievements in the first term. In developing the heat resistant element technology, the technology to grow {beta}-SiC crystals was expanded to obtaining thin film crystals with high migratory performance by using higher temperatures. At the same time, development was performed on a technology to manufacture multiple number of transistors on one substrate, such as the doping technology and etching technology. Using this technology, schottky diodes and p-n junction elements being the basic structures of MES-FET and bipolar transistors were fabricated. In the evaluation and testing technology, the {gamma} dose measuring method using TLD was improved, the traceability of {gamma} ray irradiation amount was assured, the simplified irradiation testing method using X-ray was established, and the heat resistance testing technology for electronic parts was established. Furthermore, attempts were made on enhancing radiation resistance of the elements, such as in MOS silicon integrated circuit, bipolar silicon integrated circuit, and compound semiconductor integrated circuit. (NEDO)

  14. Research and development of basic technologies for next-generation industry. Evaluation of 1st-phase research and development of 3-dimensional circuit devices; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Sanjigen kairo soshi daiikki kenkyu kaihatsu hyoka

    NONE

    1985-03-30

    The aim is to develop basic technologies relating to 3-dimensional circuit devices with an ultrahigh-density accumulation of functions therein for the embodiment of ultra-small high-performance data processing devices or artificial brain-like multiple-function data processing devices. To be developed are laminate-structure devices which have an ultrahigh-density accumulation of logic and memory functions or a complex accumulation of functions including signal and sensor functions. In the 1st phase, importance is attached to the development of a multilayer crystalline structure, which is the most elementary in the development of 3-dimensional circuit devices, and of processing technologies for them. Propositions are made and analyses are conducted relating to the enlargement of exposure region in synchrotron radiation lithography, development of a maskless beam process of a resolution of 0.1{mu}m, development of a focused ion beam device, etc. Recrystallization methods using a laser beam or a linear electron beam are developed for the growth of multilayer crystals, and are proved to be effective. The application feasibility of a flat deposition dry process etc. to laminate processing technologies is demonstrated. Concerning integration technologies, some laminated circuit devices are experimentally fabricated, and their behavior is determined. The goals of the 1st phase are found achieved. (NEDO)

  15. Industrial science and technology research and development institutions in fiscal 1999. Report on achievements in research and development of human media; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido. Human media no kenkyu kaihatsu seika hokokusho

    NONE

    2001-03-01

    In order to give the society with the full picture of human media at an early time, actual problems in industries were taken up. This paper summarizes the sensitivity agent to support sensitivity of individuals, the human media database, the urban environment human media aiming at symbiosis of nature with artificial environment, and the achievements of comprehensive investigations and researches in fiscals 1999 and 2000. Activities were taken in the following four areas: 1) research and development of the sensitivity agent and human media database, 2) research and development of the urban environment human media, 3) comprehensive investigations and researches, and 4) investigations on technological trends in foreign countries. In Item 1), discussions were given on the technology to present full-color images at high accuracy, the image sensitivity retrieval technology, and the multi-dimensional interface technology for the human media database. In studying the basic human media technology, discussions were given on the basic sensitivity modeling technology, and the sensitivity agent mechanism. (NEDO)

  16. Fiscal 1994 entrusted task report. Surveys of advanced natural gas development and efficient utilization (Survey of coal hydrogasification technology development); 1994 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

    NONE

    1995-03-01

    For the establishment of a practical process for substitute natural gas (SNG) production, technological and economical assessments were made, and tasks to discharge for the development were discussed. In this fiscal year, the results of surveys conducted in the past five-year period were compiled, and studies were made to prepare for a smooth transition to the element research stage. Findings obtained are described below. SNG producing technologies need to be developed, with the demand for SNG increasing sharply, to further stabilize the base for SNG supply; coal which is abundantly available should be used as the material for SNG; and coal hydrogasification, among various methods for producing SNG from coal, is the most suitable in view of efficiency and cost performance. It was also found after a prolonged study for the improvement of efficiency and cost performance that probabilities were high that the yield of BTX (benzene, toluene, xylene) would increase and cost performance would improve. Besides, a basic plan and an element technology research plan were prepared for the development of the ARCH (advanced rapid coal hydrogasification) process. (NEDO)

  17. Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

  18. FY 1998 Report on development of technologies for commercialization of industrial solar systems. Summary of the abstracts (Research and development management); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika gaiyo sogoban. Kenkyu kaihatsu kanri

    NONE

    1999-03-01

    The FY 1998 programs for development of technologies for commercialization of industrial solar systems include those for freezing/refrigeration systems utilizing solar heat, and international joint programs for development of technologies for the solar heat-utilizing systems. The studies are also conducted to draw the technological development programs for the solar heat-utilizing systems to be developed in the future. For development of the solar heat-utilizing freezing/refrigeration systems, the efforts are directed to extending service life of hydrogen occluding alloy to at least 10 years, which is one of the final targets. High reversibility up to 1,000 cycles is confirmed with the alloy working at low temperature for generating low-temperature heat. The international joint programs for technological development include technology evaluation of lumber drying by solar heat by operating the pilot plant, training of engineers and study on commercialization of the concept in Republic of Indonesia. The studies on technological development of solar heat-utilizing systems include those on classification of the solar heat-utilizing systems by area and utilization type, and evaluation of operating temperature levels and the merits and themes/problems. (NEDO)

  19. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  20. Fiscal 1999 geothermal development promotion survey. Development potentiality survey - Strategic survey/nation-wide survey (Report on districts in Fukushima Prefecture); 1999 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa - senryakuteki chosa zenkoku chosa (Fukushimaken chiiki hokokusho)

    NONE

    2000-08-01

    For the effective implementation of the survey, data in existence were reanalyzed for the Bandai-Azuma district and Minami-Aizu/Nasu district, and a wide area geothermal model was built. Using the model, exploitable resources were assessed and a prioritized survey introduction program was worked out for the promotion of geothermal development. In compliance with the strategic survey implementation manual, the Bandai-Azuma district was assessed, and the northeastern-eastern foot area of Azuma Volcano and the northern foot area of Adatara Volcano were extracted as areas promising geothermal energy development. The Monte Carlo method was applied to the prioritized survey area at the northeastern foot of Azuma Volcano, and then it was estimated that, with a probability of not less than 90%, the exploitable resources would be 6.4MWe in the case of data accuracy of 0.5 or more and 12.0MWe in the case of data accuracy of 0.4 or more. Selected as promising areas in the Minami-Aizu/Nasu district were the Yanaizu-Nishiyama area, the neighborhood of Nasudake-Chausudake, and the neighborhood of Shiobara-Fuji. (NEDO)

  1. Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of sodium hypochlorite activating system; 1999 nendo venture kigyo shiengata chiiki consortium kenkyu kaihatsu seika hokokusho. Jiaensosan natrium kasseika sochi no kaihatsu

    NONE

    2001-03-01

    The aim is to develop and widely diffuse a cleaning, sterilizing, and disinfecting system (chemicals and device) which is nearer to the best. A safety-conscious diluting/mixing technology was developed by which acid and sodium hypochlorite were mixed without generating any noxious gas. Using this technology, a mixing tube was developed, capable of homogeneously diluting chemicals in raw water and mixing them homogeneously. How the dilution and mixing occurred in the mixing tube was measured by an electric conductivity meter for evaluation, data on the state of diluting of the solution were plotted in a graphic chart for study, a comprehensive deliberation was made of performance, cost, etc., and then a device was experimentally constructed. A concentration level detecting sensor section and a metering pump were developed. The pH adjustment and disinfecting effect were assessed using various acids, and then it was found that the acetic acid was the most suitable in view of safeness, disinfecting effect, stability, and ease of adjustment. Based on the result of a comprehensive technical survey, a system was designed suitable for artificial dialysis, food processing, and cleaning and disinfecting of endoscopes. A prototype was built, and the development effort progressed to reach a level where a prototype was built and subjected to a field test. (NEDO)

  2. Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

    NONE

    1999-03-01

    For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

  3. FY 1999 report on the development of technology to recycle architectural waste materials, glass, etc. Development of technology to recycle architectural waste materials; 1999 nendo kenchiku haizai glass nado recycle gijutsu kaihatsu seika hokokusho. Kenchiku haizai recycle gijutsu kaihatsu

    NONE

    2000-09-01

    Waste wood materials in the materials discharged from architectural disassembly were regarded as a potential wood resource, and the R and D of the technology to recycle these were conducted. Studies were made on the technology to finely grind waste wood materials, technology to compress/form waste wood materials and ground wood powder, verification of strength characteristics/dimension stability of the formed wood materials, etc. As to the wood materials which were badly degraded under ultra violet rays, they were coloring-processed by the steam treatment, and a possibility of coating substitution was confirmed. In relation to the technology to produce compressed wood materials, the optimization of heat treatment conditions was experimentally conducted. About the technology to give dimensional stability, dimensional stability was improved as a result of the improvement of chemicals feeding and the development of chemically processed drugs. In the development of light formed products, the board was successfully formed which is light in weight using lignocelluloses/inorganic hydrates and has the bending strength higher than that of the plaster board. In the development of interior materials, the technology was developed in which ground wood powder and thermo-plastic resin are mixed for die molding, and the OA floor using this was commercialized. (NEDO)

  4. FY 1999 Report on research and development of power generation by solid electrolyte fuel cell. Research and development of solid electrolyte fuel cell; 1999 nendo nenryo denchi hatsuden gijutsu kaihatsu kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu kenkyu seika

    NONE

    2000-06-01

    This project is aimed at establishment of the module basic technology and commercialization of the solid electrolyte fuel cell in the early stage by designing, construction, operation and performance evaluation of a several kW-class module which incorporates the cylindrical cell fabricated by the wet process. The FY 1999 R and D efforts include (1) cell performance demonstration study: the cylindrical single cell fabricated by the wet process is demonstration-tested to determine the initial performance and durability for continuous operation, thereby comparing the external reforming with internal reforming in output, with the internal reforming rate as the parameter, (2) development of a several kW-class module: the adequate cell arrangement structure within the module is studied by the computer-aided simulation, and the tests for confirming thermal cycle durability of the modified bundle are conducted using the module power generation unit and the several kW-class module is tested, and (3) development of the technology for designing a thermally supported module: the effects of, e.g., air and fuel supply conditions on the module performance are analyzed using the analytical model as the base. Expansion of the module level to the process simulation model has been completed, based on these results. (NEDO)

  5. International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

    NONE

    2000-03-01

    As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

  6. Report on achievements in fiscal 1999. Development of technology to put photovoltaic power generation system for industrial use into practical use (Summary of comprehensive achievement); 1999 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Kenkyu kaihatsu kanri

    NONE

    2000-09-01

    NEDO is proceeding with the development of a technology to put photovoltaic power generation system for industrial use into practical use, with an aim of simultaneous solution of sustainable growth and environmental problems. In developing an advanced heat process type system, selection was made on high-performance refrigeration materials for a stand-alone type refrigeration system capable of dealing with levels of minus 20 degrees C or lower (Ti-Ni-Zr-Mn-V based hydrogen absorbing alloys for use at low temperatures, and La-Ni-Sn-Al based hydrogen absorbing alloys for regeneration use). Evaluations were given on the developed refrigeration system by using the dynamic property simulation technology. The developed system achieved a cold heat acquiring temperature of minus 20 degrees or lower, and a heat output of 1,500 kcal/hr or more under the conditions of outside air temperature of 28 degrees C, and collected solar heat temperature of 140 degrees C. CO2 reduction unit requirement was calculated from LCA on a solar heat utilization system with which the future technological development is expected to aim at. Themes proposed to be promoted in the future would include a direct heat utilization system such as the building material integrated system, a freezing and refrigeration system, a high-temperature light and heat collecting system, a harmful substance analyzing system, a high temperature utilizing fuel synthesizing system, a high-efficiency heat storing system, and a snowy cold region system. (NEDO)

  7. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  8. FY 1999 Report on research and development of power storage by high-temperature superconducting flywheel. Research and development of permanent magnet; 1999 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu eikyu jishaku no kenkyu kaihatsu seika hokokusho

    NONE

    2000-05-01

    The R and D program is implemented for permanent magnet, as part of the project aimed at commercialization of a 10 MWh-class high-temperature superconducting magnetic bearing type power storage system. A speed of rotation of 28,570 rpm is attained by using an iron intermediate ring for a Pr permanent magnet rotator and reinforcing the rotator with a plastic hoop reinforced with carbon fibers three-fold (CFPR hoop). The speed is increased to 31,300 rpm by interlacing carbon fibers also in the radial direction and replacing iron for the intermediate ring by titanium. The highest speed of rotation of 33,506 rpm is realized by the rotator of permanent magnet of sintered Nd. The magnetic circuit of stronger, more smooth magnetic field needs the permanent magnet of less uneven magnetic flux. The magnet is of a monoaxially anisotropic rare-earth metal, with four-fold magnetic ring bodies having fan-shaped small pieces arranged on each ring. Uneven magnetic flux occurs at the joint between these small pieces. The one-body-ring magnet of radially anisotropic, sintered Nd is developed, and incorporated in the repulsion type magnetic circuit, to reduce unevenness of the magnetic flux. (NEDO)

  9. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  10. Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

    NONE

    1982-03-01

    To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

  11. Fiscal 2000 report on result of R and D on robot system cooperating and coexisting with human beings. Development of energy conservation technology; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    NONE

    2001-06-01

    Introduction of a number of robots and consumption of a large amount of energy are unavoidable if a complicated process operation is to be carried out by robots in an extensive work site. Great energy conservation is contrived by developing robots applicable to manufacturing in performing a variety of operations in place of human beings and thereby reducing the number of robots to work. This paper explains the fiscal 2000 results. For dual-handed cooperative tasks, a function was examined capable of gripping an object without giving a humanoid robot an instruction of an exact gripping position. A method was designed to prepare a command for the other arm through a command for one arm, with torque impedance control employed for the purpose of avoiding damage due to collision. A study was conducted on a three-dimensional shape detecting model using a visual device of a robot. In grasping problems of balance control of a humanoid robot, the behavior of a robot consisting of multi-links was considered as behavior of inverted pendulum, with possibility checked for the stabilization of the balance. For the purpose of putting the virtual robot platform previously developed to practical use, a three-dimensional operation tool of run-time user interface was developed, with research conducted on the sophistication of robot application. (NEDO)

  12. Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

    NONE

    1999-03-01

    This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

  13. FY 1993 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1983 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    NONE

    1994-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1993 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  14. FY 2000 report on the results of the R and D of femtosecond technology. Development of the ultra-short pulse optoelectronic technology; 2000 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

    NONE

    2001-03-01

    This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. Especially, it aims at establishing the basement technology of the ultra-high speed optoelectronics which are absolutely necessary for construction of the Tb/s class ultra-high speed/large capacity information communication infrastructure. The results obtained in this fiscal year were as follows: successful transmission of 144km of 600fs optical pulse, successful experiment of 4-chain pulse DEMUX equivalent to 1Tb/s by ultra-high speed intersubband transition optical switch of Sb-base material combination quantum well, realization of 2-bit coding/decoding in the spectral region, realization of serial-parallel conversion motion of optical pulse equivalent to 1Tb/s using squarylium J aggregate thin films, realization of subpico second optical pulse 20nm wavelength conversion by DFB laser structure, etc. (NEDO)

  15. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

    NONE

    2000-03-01

    The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

  16. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

    NONE

    1989-05-01

    Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

  17. Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

    NONE

    2001-03-01

    With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

  18. Research and development of basic technologies for next-generation industries. Evaluation of 2nd phase research and development of technologies of mass culture of cells; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saibo tairyo baiyo gijutsu. Dainiki kenkyu kaihatsu hyoka

    NONE

    1987-03-30

    The project aims to establish basic technologies for the mass culture of cells which will enable a large, stable supply of fine chemical products whose industrial production the conventional technique of synthesis has failed to realize. In the 1st phase, cell stains were selected, a serumless medium was developed, basic culturing conditions were established, and substances production rates were improved, and the 2nd phase stands succeeding these 1st phase achievements. Toward the ultimate goal of establishing basic technologies for serumless high-density cultures for industrial use and technologies for isolating and refining useful substances, a small-scale optimum culture technique and a serumless culture technique are developed. Serumless cultures are developed for strains of man's lymphoid cells, cells deriving from bone marrow, epithelial cells, and hybridomas of man and mouse, all these sampled during the 1st phase endeavors. Success is attained in growing each cell strain on a scale of 1-10L to increase to 10{sup 7} cells/ml or more in population density. It is found that each cell strain produces useful substances, such as man's monoclonal antibodies and elements involved in the multiplication or differentiation of new cells. (NEDO)

  19. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  20. Research on natural gas fuel injection system. Development of high-performance pressure regulator; Tennen gas yo nenryo funsha system no kenkyu kaihatsu. 1. Tennen gas nenryo funshayo no koseino regulator kaihatsu

    Kato, S; Ishii, M; Takigawa, B; Makabe, K; Harada, S; Ono, H [Nippon Carburetor Co. Ltd., Tokyo (Japan)

    1997-10-01

    With the aim of further reducing the exhaust emissions of natural-gas vehicles, vigorous research and development work is under way today on multi point gas injection (MPGI) system. In this studies, a high-performance pressure regulator, which is one of the main components of this MPGI system, has been newly developed. The results showed that a significantly better accuracy of the regulated pressure level using this regulator was obtained under the wide range of operating conditions, including instantaneously greater changes of fuel flow rate. In addition, the advanced studies of gaseous fuel injectors (GFIs) would be also conducted. 4 refs., 8 figs.

  1. Development of active rear steer actuator. Development of four wheel steer actuator for active safety; Active rear steer actuator no kaihatsu. Yobo anzen ni muketa 4WS actuator no kaihatsu

    Yamanaka, T [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, ecology, energy saving and safety have become important issues. And Active Safety is spotlighted in vehicle control area. Many researches and developments on four wheel steer system have been done to improve vehicle stability. We have developed the Active Rear Steer system with electromechanical Actuator, which is mass-productive, compact, and high response and durable. 10 figs., 5 tabs.

  2. Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

    NONE

    1997-03-01

    The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

  3. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  4. Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

    NONE

    1997-03-01

    For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

  5. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  6. Fiscal 1974 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1974 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

    NONE

    1975-05-29

    This report summarizes the fiscal 1974 research result on the solar heat power generation system with a tower light collection system. This system receives solar radiation energy by reflector group, and concentrates solar energy reflected by each reflector on the heat absorber mounted on the top of the tower. A ratio of the whole reflector group area to the receiving area of the heat absorber is called a concentration factor. The heat absorber converts concentrated dense radiation energy to thermal energy, and transfers heated thermal medium to the bottom of the tower to supply solar heat to a thermal plant after appropriate treatment. Based on the above basic idea, study was made on the total system and each subsystem, and some problems on component equipment and materials were extracted. After solving these problems and improving the whole system accuracy, these results are put to practical use for design and operation of an actual pilot plant. The main research items are as follows: feasibility study, simulation, element study, preparation of a 10kWT test equipment, and planning of a 1,000kW class pilot plant. (NEDO)

  7. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  8. Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

    NONE

    1989-05-01

    This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

  9. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  10. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of HFC-23 destruction technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. HFC-23 hakai gijutsu no kaihatsu

    NONE

    2000-01-01

    HFC-23 is produced as a by-product during HCFC-22 manufacturing (produced at by-production rate of about 2%, whereas the reaction control has limitation in reducing the production). This is one of the substances subjected to the greenhouse effect gas reduction in the climate change framework treaty. This paper describes the achievements in 1998 on developing the HFC-23 destruction technology. High-temperature pyrolysis decomposes the substance into HF and CO2, which are given absorption treatment by water and alkali to make them harmless, and are recovered finally as calcium fluoride. An equipment having the treatment capability of 195 kg/h was constructed. Design was made on a facility capable of treating fluorine containing waste water at 3 t/h at maximum. Utilities consumed in a factory (industrial water, acids for neutralization, and alkali) are used effectively to identify the effect of reducing the treatment cost. Discussions were given from the safety aspect on facilities to prevent leakage of fluorine containing waste water being a harmful substance. Fabrication was executed on a full-size treatment testing equipment that can utilize the utilities in the factory effectively, and trial equipment operation was performed to arrange the system prepared toward the future tests and researches. (NEDO)

  11. 1998 Annual Study Report. Research and development of power storage by high-temperature superconducting flywheels (research and development of permanent magnet); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (eikyu jishaku no kenkyu kaihatsu)

    NONE

    1999-05-01

    The permanent magnets have been investigated and developed, for eventual commercialization of a 10 MWh power storage system by high-temperature superconducting flywheel. The permanent magnet rotors have been already developed in the previous years using a praseodymium-based magnet (Pr magnet) and neodymium-based sintered magnet (Nd sintered magnet), and the target rotational speed of 30,000 rpm has been attained. For development of the magnetic circuit to produce a stronger and smoother magnetic field, magnetic flux density of the Nd sintered magnet is measured. It shows a lower magnetic flux irregularity than the Pd magnet, but there is still room for further improvement. For development of large-size permanent magnet fabrication techniques, it is confirmed that the large-size Nd sintered magnet can be easily magnetized by partial magnetizing, as is the case with the Pr magnet. In this year, the irregular magnetic flux is three-dimensionally simulated, based on the results obtained in the previous years, to find that the simulated results are in good agreement with the observed ones. The measures to solve the problems are also investigated. It is also confirmed that the large-size ring magnet can be easily magnetized by partial magnetization. (NEDO)

  12. Achievement report on research and development of the industrial basic technologies of the next generation in fiscal 1981. Research and development of composite materials; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Fukugo zairyo no kenkyu kaihatsu

    NONE

    1982-03-01

    Described herein are the results of the FY 1981 research and development for composite materials, established by the R and D system for the basic technologies of the next generation. The R and D project for resin-based composite materials involves basic researches on the matrix resins, and surface modification of the reinforcing fibers. The investigations and basic tests are conducted for monolithic molding, other types of molding, and cutting and boring by, e.g., laser beams and water jet. The other related efforts include researches on analysis theories for optimization of strength and rigidity of the composite structures, and development of the optimization programs. For the R and D project for the metal-based composite materials, the efforts are directed to understanding wettability and reactivity of the reinforcing fibers with metals, and development of the techniques for producing various types of preforms and compositing methods. The basic researches are conducted for hot pressing/rolling molding, extrusion/withdrawal, powder molding and melt molding of the composite materials with aluminum alloys as the matrices. The other R and D items include investigations on methods for evaluating qualities for the steps form the stock preparation to production of the final products. (NEDO)

  13. Report on 1979 result of R and D under Sunshine Project. Development of coal liquefaction technology (development of solvent treatment and liquefaction plant); 1979 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Yozai shori ekika plant no kaihatsu

    NONE

    1980-03-01

    A report was made on the result for fiscal 1979 of the development of a coal solvent treatment and liquefaction plant. With the purpose of establishing a technology of making equipment for a coal liquefaction plant by a solvent treatment method, R and D were conducted on a solid liquid separation method and on the construction and operation of an experimental equipment having a scale of the maximum 1 t/day coal processing, providing technical data for the construction of an efficient coal liquefaction equipment. In studying the operation of a centrifugal separator, it was run using heating solvent, dummy slurry and coal extraction slurry, with no abnormality found in each equipment and with knowledge obtained of the separation state of the solid. The machine is capable of obtaining SRC of 0.2-0.3% low ash contents. Water operation was performed for the extraction processing device (agitation tank, heating furnace, compression pump, circulation pump, etc.) of the 1 t/day experimental plant and, as a result, a relation was confirmed between a water flow rate and pressure loss of the piping part. The detailed design, manufacture and installation were completed for a part (pulverizer, solvent tank, feeding pump, etc.) of the equipment for the coal pre-processing slurry making process and the extraction process, with a trial run implemented for adjustment and confirmation of the operation. The cold/hot continuous trial run by a solvent smoothly proceeded, proving the performance to be the same as the specifications. (NEDO)

  14. Development of large scale wind energy conservation system. Development of control techniques for assembly-type wind power generating systems; Ogata furyoku hatsuden system no kaihatsu. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of control techniques for assembly-type wind power generating systems. The study on optimum system configuration produces 50 to 100kW wind power units for screening small-size wind power plant types, and, at the same time, surveys performance of commercial units and experiences of 9 makers capable of producing the above units. As a result, 3 MICON`s units (output: 100kW, active YAW control, monopole tower, maximum wind speed: 60m/s) are selected. The study on optimum operational techniques integrates 2 medium-size power units into a power line, showing a service factor of 30.2% on the annual average, monthly varying in a range from 11.8 to 45.0%. These units, installed in Miyako Island, were attacked by 3 typhoons of wind velocity of 25m/s or higher in 1994, and the only damage recorded is that of the anemoscope/anemometer. It is found that No.1 unit is located at a better geographical point than the No.2 unit, to produce a higher output. 3 figs., 3 tabs.

  15. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  16. Report for fiscal 1998 on results of research and development of silicon-based polymeric material. Material research for the liquid methane fueled aircraft engine; 1998 nendo keisokei kobunshi zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine kaihatsu

    NONE

    1999-03-01

    Research was conducted for the purpose of establishing basic technology concerning molecular design, synthesis, material formation, and evaluation of silicon-based polymers which are expected to provide superior electronic/optical functions, high heat/combustion resistance and dynamic properties. The research subjects were such as following: research and development of silicon-based polymeric materials with sea-island microstructures; research and development of silicon-based polymeric materials with sea-island microstructures; research and development on IPN formation with silicon-based polymers; research and development of hybrid silicon polymers with organometallic compounds; research and development of silicon containing polymer materials with ring structures; general committee for investigation and research; the optimized low-temperature Wurtz synthesis and modification of polysilanes; study of unsaturated and hypercoordinate organosilicon compounds; basic studies on the synthesis and properties of silicon-based high polymers; studies of new monomer-synthesis and their polymerization reaction; studies on new method of preparation and functionalization of polysilanes; novel applications of silicon-based polymers in imaging devices for information display, memory, and recordings; and molecular design of silicon-containing {pi}-conjugated and {sigma}-conjugated compounds. (NEDO)

  17. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  18. Fiscal 1976 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cell); 1976 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    NONE

    1977-05-30

    This report describes the fiscal 1976 research result on new type solar cells for photovoltaic power systems. On junction formation, the solar cell fabricated by spray coating showed output characteristics equivalent to that by rotary coating or phase diffusion, and inexpensive coating liquid, 1/40 of commercially available liquid in price, showed a sufficient result, however, the conversion efficiency of P{sup +}/N elements was insufficient. Schottky barrier polycrystal Si thin film was suitable for large-area elements without any property degradation. Small grain boundary density of polycrystal layers was also necessary. Temperature characteristics of collector element structure with a comb electrode were calculated theoretically. Change in diffusion length of minority carriers due to temperature well agreed between measured and calculated ones. Optimization calculation was also carried out. The size, curve, weight and transmissivity of plastic and glass materials for solar cell packaging were evaluated by continuous outdoor exposure tests. Fluorinated ethylene-propylene, methyl methacrylate and polycarbonate plates and glass were the most promising materials because of less deformation. (NEDO)

  19. Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    NONE

    1999-03-01

    In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

  20. Research and development of a high-temperature superconducting flywheel energy storage system. Research and development of the New Sunshine Program; Furaihoiru denryoku chozo shisutemu kenkyu kaihatsu. Nyu sanshain keikaku ni motozuku kenkyu kaihatsu

    Nakagawa, Y. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1999-11-25

    The project conducted by NEDO for developing a high-temperature superconducting flywheel energy storage system is introduced; the two test results of fundamental studies are described. One is the measurement of levitation force and rotation loss of superconducting magnetic bearings composed of oxide superconducting bulks and permanent magnet composite. Two types of superconducting magnetic bearings. axial and radial types, were fabricated and tested. The other test was the fabrication and testing of two functional models. A small-sized superconducting flywheel model of the 0.5 kWh class was fabricated and tested. A medium-sized rotating functional model of the 10 kWh class was fabricated as well. (author)

  1. FY 1999 report on the results of the R and D of femtosecond technology. R and D of femtosecond technology; 1999 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Femto byo technology no kenkyu kaihatsu

    NONE

    2001-03-01

    This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. The themes are as follows: 1) R and D of ultra-short pulse optoelectronic technology; 2) R and D of ultra-short optical pulse applied measuring technology. In 1), in addition to the investigational study of the ultra-high speed light source technology, ultra-high speed modulation technology and ultra-high speed switching technology which are needed for the ultra-high speed optical information communication system and the construction, made were the survey and the evaluation of crystal growth technology/process technology of new semiconductor materials which make the fabrication of these high-tech ultra-high speed devices possible. In 2), investigationally studied were the technology for generation/control of ultra-short optical pulse and ultra-short electron beam pulse and the technology for stabilization, and the technology for generation of femtosecond high-intensity X-ray pulse by collision of optical pulse with electron beam pulse. (NEDO)

  2. FY 1999 report on the results of the R and D of femtosecond technology. Development of ultra-short pulse optoelectronics technology; 1999 nendo femutobyo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

    NONE

    2000-03-01

    The paper described the FY 1999 results of the R and D of femtosecond technology. For the purpose of creating new industrial basement technology which supports the highly information-oriented society in the 21st century, the ultra-high speed electronics technology is indispensable which is beyond speed limits of the existing electronics technology and has new functionality. The ultra-high speed electronics basement technology is established through the R and D of the technology to control the state of light and electronics in the femtosecond time domain (10{sup -15} - 10{sup -12} second). Themes of the R and D are technology to generate/transmit femtosecond optical pulse, technology for control/distribution, and ultra-short pulse optoelectronics common basement technology. In FY 1999, a lot of results were obtained in the following: generation of the pulse train highly repeated at 500GHz in semiconductor laser; 139km transmission of 250fs optical pulse; switching movement at ultra-high speed of 150fs-1.2ps in transition among subbands of GaN base and Sb base materials; DEMUXA movement toward 160-10Gb/s in Mach-Zehnder type optical switch. (NEDO)

  3. Report on achievements in research and development in fiscal 1982 commissioned from the Sunshine Project. Development of a pit condition measuring technology (Development of a fracturing technology); 1982 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

    NONE

    1983-03-01

    Development was made on a measuring instrument intended of acquiring information inside geothermal wells under high temperature and pressure. Research and development was performed on a fracturing technology to enhance characteristics of wells. What have been performed as a result of the development of the in-pit measuring instrument are application of high temperature logging cables as a result of development of logging devices, and the fabrication of a digital data analyzer. In developing the logging and reservoir evaluating technologies, field test were performed by using a logger that uses neutrons, installed with a radiation source. In developing the fracturing technology, discussions were given on the equation of relationship proposed from the standpoint of fracture dynamics, and investigations were made on examples of values, in order to anticipate hydraulic fracturing pressure applied in fracturing. In the research of fracturing additives, discussions were given on gelling agents supported by use of water glass, and alumina prop agents. For the preliminary observation devices, a high-pressure low flow rate control device was installed on the high-pressure plunger pump, improvement was made on the composite centrifugal multi-stage pump. (NEDO)

  4. Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    NONE

    1998-03-01

    Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

  5. 1998 report on development of high-efficiency waste power generation technology. 2. Development of waste gasification and ash melting power generation technology; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Haikibutsu gas ka yoyu hatsuden gijutsu kaihatsu

    NONE

    1999-03-01

    In regard to waste gasification and ash melting power generation, a basic test and examination were conducted in fiscal 1998, with a full-scale development test made ready to start. In the development of technology for raising steam temperature, evaluation of high temperature corrosivity of SH materials and development of high-temperature dust removal system were carried out for example, as were development of dechlorination technology for thermal decomposition process and development of ceramic high-temperature air heater. In the development of technology to prevent exhaust gas reheating, preliminary examination was made on denitrification technologies using a catalyst with superior low-temperature activity. In the development of technology to reduce self-heat melting critical calorific value, investigation and basic test were carried out concerning a stable waste feed system, with a pilot test device experimentally manufactured and tested based on the findings. In the development of technology for reducing external fuel input, examination and analysis were performed on pretreatment techniques for waste plastics, with basic data obtained for a waste blowing system project. In addition, the thermal decomposition and combustion characteristics of waste plastics were clarified by the basic test. (NEDO)

  6. Development of free running differential. Development of differential with an actuator and a clutch which disconnects the traction; Free running defu no kaihatsu. Kirippanashi kiko oyobi actuator wo naizoshita differential sochi no kaihatsu

    Yamazaki, N; Teraoka, M; Ishikawa, O; Nagaoka, T; Ugajin, K [Tochigi Fuji Sangyo Co. Ltd., Tochigi (Japan)

    1997-10-01

    Free Running Differential has an effect on fuel economy and noise reduction from drive line for four wheel drive vehicle. It has an actuator and a clutch which disconnects the traction from no driving side tire when two wheel drive is selected. this unit can be installed in conventional differential carrier with no design change. It is compact in design and low in cost. We evaluate it as having a dominant position among any other Free running system. 7 figs.

  7. Fiscal 1981 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant. Conceptual plant design; 1981 nendo nessui riyo hatsuden plant no kaihatsu / binary cycle hatsuden plant no kaihatsu seika hokokusho . Plant gainen sekkei

    NONE

    1982-03-01

    Conceptual design was made on a 10MW class binary cycle power plant for a demonstration plant superior in reliability and profitability, under most realistic current geothermal field conditions. In the design, study was made on heat balance, main pipe system, equipment allocation, and electric system for a plant system configuration, and study was also made on preheater, evaporator, condenser, turbine and others for plant component equipment. Further study was made on optimization of mist cooling condenser, instrumentation, control, utility, and environmental measures. The following basic data were obtained through the conceptual design: plant inlet hot water temperature: 130 degrees C, plant outlet hot water temperature: 70 degrees C, hot water flow rate: 1,415t/h, working fluid: R-114, R-114 pressure in evaporator: 11.98kg/cm{sup 2} abs, R-114 evaporation temperature: 91.1 degrees C, R-114 condensation temperature: 31.0 degrees C, R- 114 flow rate: 2,265t/h, site area: 106.5m x 102.4m, building area: 48.7m x 16.8m, and building height: 13.0m. (NEDO)

  8. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzokukei)'. Daiikki kenkyu kaihatsu hyoka

    NONE

    1983-03-31

    The results of the first phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to understanding the basic characteristics regarding wettability and reactivity of PAN-based carbon fibers and PCS-based silicon carbide fibers with metals, in which aluminum-based matrices are considered; preliminary tests for various composting methods; and development of wire preforms as the intermediate materials. Bright prospects have been obtained for improving problems involved in each technique. For development of molding/processing techniques, basic researches have been conducted for hot pressing/rolling, extrusion/withdrawal, powder molding and melt molding, using various reinforcing fibers. Bright prospects have been also obtained for combinations of adequate molding processes for individual materials. For development of design techniques, the basic data regarding mechanical characteristics of FRMs, both domestic and foreign, are collected, and analyzed by the trace tests with specimens, to set up the targets for FRM function improvements, viewed from the designs. (NEDO)

  9. Fiscal 1974 Sunshine Project result report. R and D on photovoltaic power generation system (R and D on new type solar cells); 1974 nendo taiyoko hatsuden system no kenkyu kaihatsu seika hokokusho. Shingatashiki taiyo denchi no kenkyu kaihatsu

    NONE

    1975-05-27

    This report summarizes the fiscal 1974 research result on R and D of new type solar cells, which includes researches on (1) solar cell structure, (2) packaging, and (3) improvement of a conversion efficiency. In the 1st research, theoretical study was made on the relation between a solar cell efficiency and various design factors to obtain basic data for ordinary cell structure and vertical junction type cell structure. As impurity source, a thermal diffusion method using doped oxide by CVD was compared with that using boron nitride, resulting in no difference in solar cell characteristics between both methods. The measurement results on contact resistances of Al, Fe and Ni with electrodes prepared by electron beam deposition showed that these materials are applicable to Si more than 10{sup 18}/cm{sup 3} in impurity density as electrode materials. In the 2nd research, exposure tests were made on some kinds of specimens, resulting in no troubles. Study was made on production costs and structures suitable for automatic production of 4 kinds of packages with different basic structures. In the 3rd research, the prototype solar cell was prepared to use under solar radiation within 20SUNS. (NEDO)

  10. FY 1992 report on the results of the commissioned research and development project. R and D of SOFC (solid oxide fuel cells); 1992 nendo nenryo denchi hatsuden gijutsu kaihatsu seika hokokusho. SOFC kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    NONE

    1983-05-01

    The research and development project is carried out for fuel cell power generation technologies and solid electrolyte type fuel cells, and the reports on the FY 1992 results issued by the participant organizations are summarized. For R and D of the modules, Fuji Electric conducted the R and D for the large-area, cell-stacked type, and Sanyo Electric for the composite cell-stacked type. For R and D of the materials and fundamental technologies, Fine Ceramics Center is conducted the R and D for microscopic structures of the electrode, Fujikura for electrode structures produced by spraying or the like, Mitsubishi Heavy Industries for multi-functional fuel electrodes, Murata Seisakusho for co-sintering technologies, and Mitsui Shipbuilding for current collecting technologies. For R and D of the systems, Central Research Institute of Electric Power Industry conducted the R and D for the systems, Electric Power Development and Mitsubishi Heavy Industries jointly for designs of the cell peripheries, and the Japan Research and Development Center for Metals for elementary technologies for the peripheral devices. (NEDO)

  11. Development of a new electric battery electric power storage system. Results of the 12-year R and D; Shingata denchi denryoku chozo system kaihatsu. 12 nenkan no kenkyu kaihatsu no seika

    NONE

    1999-07-01

    The paper described the results of the R and D which have been continued for 12 years on a new electric battery electric power storage system (load leveling function). The electric batteries for study were Na-S, Zn-Cl, Zn-Br, and redox type. Charge/discharge operation of 211 times was conducted of a pilot plant with a Na-S battery 1,000kW and 8-hour capacity. The overall efficiency of system was 71.5-76.0%, and the energy efficiency of battery was 86%. As a whole, the performance was able to be confirmed which can fulfil a developmental target. The system overall efficiency of 65.9% and battery efficiency of 76.1% were obtained. The experiment on battery life was carried out at plant together with the pilot operation. The mean life of Na-S battery was estimated at 800 cycles, and that of Zn-Br battery at 500-800 cycles. The effectiveness of the new electric battery electric power storage system was technically verified. For the future commercialization, studies on the following are needed: enhancement of reliability, easiness in maintenance/inspection, size reduction, cost reduction, etc. (NEDO)

  12. FY 1998 report on the R and D of the industrial science technology. R and D of synergy ceramics; 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

    NONE

    2000-03-01

    Hazardous ingredients in gases exhausted from diesel, refuse treatment facilities, etc. are becoming the problem. The development is expected of porous ceramic films which have functions of separation/purification at high temperature. By making good use of the technology to synthesize ceramic films with uniform through pores of several ten nm order and the technology to form 1D through pores of several ten - 100{mu} m order, the development of the following technologies were made and are in sight: enhancement of functions of gas separation/purification, function of catalyst-carrying to be given, porous film formation/base material fabrication. For the commercialization of high performance structure use ceramic parts, required is innovation of the production method by which the production cost is reduced without damaging the characteristics. Technologies were used of micro-fine raw materials, rapid sintering, texture assessment, analysis, etc., and study was made of cost reduction in high performance ceramic parts. For energy conservation by reducing the sintering temperature, the following were trially conducted: mechanical ironing, use of low grade raw material, use of superplastic reformation and forging, etc. (NEDO)

  13. NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

  14. Research and development of a superconducting flywheel power storage system in fiscal 1998. Research and development of rotation control technology; 1998 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. Kaiten seigyo no kenkyu kaihatsu

    NONE

    1999-05-01

    Element technology research was performed on 'rotation control' aimed at practical application of a 10-MW class high-temperature superconducting flywheel power storage system. As part of the research, researches were carried out on small-size and middle-size models, low-loss control type magnetic bearing, and large-size models. For the small-size model, as a result of performing performance tests on the protective bearing by using a testing machine, it was revealed that the model is free of problems in the test for up to 5000 rpm. For the middle-size model, fabrication and installation were completed on a middle-size rotation control testing equipment having CFRP-made flywheel with a diameter of 1 m. In the control type bearing, as a result of adopting a homo-polar type magnetic pole, the rotation loss was reduced to about 1/5 of that of a hetero-polar type. The amount is about 75 W (12000 rpm) when the bias current is 1.5 A. Concept design was implemented on a 2-MWh flywheel bearing system supported with a high-temperature superconducting magnetic bearing as a full-size flywheel. The CFRP-made flywheel has a diameter of 4 m, and a circumferential velocity of 1200 m. (NEDO)

  15. Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

    NONE

    1985-03-30

    The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

  16. Research and development of the industrial basic technologies of the next generation, 'composite materials (fine ceramics)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fine ceramics'. Daiikki kenkyu kaihatsu hyoka

    NONE

    1984-03-30

    The results of the first phase research and development project for developing fine ceramics as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop fine ceramics of high strength, corrosion resistance, precision and wear resistance, noting their excellent characteristics. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at development of silicon nitride and silicon carbide for synthesis of the stock materials; explosive forming/treating the stock powders; forming, sintering and processing/joining; evaluation of the characteristics; non-destructive testing methods; designs; and evaluation of the parts, among others, as the elementary techniques for production, evaluation and application of the fine ceramic materials. The technical targets of improving functions have been achieved, or bright prospects have been obtained therefor in development of the techniques for synthesis of the stock materials, forming/sintering and processing/joining. The silica reduction for stock synthesis, basic techniques for molding/sintering, and rheological considerations for the molding/sintering techniques represent the techniques of the next generation, because they break through the limitations of the conventional techniques. (NEDO)

  17. Research and development of basic technologies for next generation industries, 'high crystalline polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo (dainiki kenkyu kaihatsu kenkyu)

    NONE

    1988-03-01

    This research and development is intended to establish a basic technology related to high crystalline polymeric material that has dynamic properties comparable to metallic materials by single polymeric material as a structural material. Thick and large high-elasticity molded forms were obtained by searching poly-arylate material, and by developing such processing technologies as high-pressure injection molding, composite injection molding, and elongation fluidity molding. High-elasticity molded forms with uniform internal orientation were obtained by heating and molding liquid crystal polymers under high magnetic field. Solution molding was performed on a molecular composite consisting of rigid chains and soft chains, which was laminated and bonded to have obtained an isotropic form with as high elasticity as 54 GPa. In addition, high pressure powder formation of cross-linked polymers of di-acetylene system provided an isotropic form with sound wave elasticity of 23 GPa.

  18. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

    NONE

    1988-03-01

    The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

  19. FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    NONE

    1995-09-01

    This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

  20. Fiscal 1999 achievement report on interuniversity coordination type research and development of industrial technology. Research and development of highly functional material designing platform; 1999 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    NONE

    2000-03-01

    For the purpose of enabling prediction of structures and properties of polymeric materials by computer-assisted experiments, studies were conducted for putting new simulation technologies to practical application. With the coarse-graining molecular dynamic method working group, a coarse-graining molecular dynamic engine high in generality and augmentability was developed so that an optimum coarse-graining model might be chosen and constructed to achieve any given purpose, and its installation was almost completed. The dynamic mean field method working group fabricated a new general-purpose simulator with its interface simplified and function improved. A simulation technique was also developed, which would be incorporated into the general-purpose simulator. The dispersed structure simulation working group developed a group of class libraries for use in continuum simulation. The platform working group, making use of Java excellent in general-purpose feature, worked out a function verification platform to run on Windows95/98/NT. (NEDO)

  1. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  2. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  3. Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

    NONE

    2000-03-01

    With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

  4. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  5. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

    NONE

    1989-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

  6. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    NONE

    1997-03-01

    Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

  7. Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

    NONE

    1998-01-01

    This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

  8. Fiscal 2000 achievement report. Development of technologies for waste treatment and recycling (Development of technologies for appropriate treatment of air bags); 2000 nendo haikibutsu recycle kanren gijutsu kaihatsu seika hokokusho. Air bag tekisei shori gijutsu no kaihatsu nado

    NONE

    2001-03-01

    A centralized treatment process respecting environmental protection and safety for unused air bags aboard disused automobiles is developed. In concrete terms, a heating facility owned by Daicel Chemical Industries, Ltd., is used, which includes an apparatus for examining exhaust gas dioxins and an exhaust gas treatment apparatus and, with this facility, studies are made for appropriately treating waste gas and waste water to be generated when air bag modules undergo centralized heating. Endeavors in fiscal 2000 center about (1) the development of waste gas treatment technologies, (2) development of waste water treatment technologies, (3) chemical analysis of waste water sludge, dusts and air bag residues, and (4) the study of appropriate treatment of non-azide air bag modules. As to the development of exhaust gas treatment technology, it was proved that the exhaust gas treatment system consisting of secondary incineration furnace, exhaust gas cooling tower and bag filter worked effectively. (NEDO)

  9. R and D project for large industrial technologies in fiscal 1990. Report on achievements in R and D of robots for critical works; 1990 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

    NONE

    1991-01-01

    Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1990. In the R and D of tactile sensors, a prototype multi-element sensor array applicable to fingers of a robot hand was produced, and the characteristics test was conducted. In the R and D of motive force technologies, a force controlled actuator for wrist containing a torque sensor was designed and produced on a trial basis, whereas evaluations were given on the size and weight reduction and the force control performance. Regarding the actuator with redundant degree of freedom, a force controlled arm was attached with an actuator with three degrees of freedom to have performed an evaluation experiment. With regard to a small size and light weight controller, fabrication was carried out on a multi-function, high-density controller which adds positional control and peripheral interface functions to the force controlling function, and an evaluation was given. In the R and D of robot language, discussions were given on robot languages related to each system of movement, manipulation, and sensors, and the grammar specifications were prepared. (NEDO)

  10. Report on fiscal 2000 basic survey for coal resource exploration. Survey for development of new exploration technology (Exploration of shallow layers on the land); 2000 nendo sekitan shigen kaihatsu kiso chosa hokokusho. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    NONE

    2001-09-01

    Efforts are made to develop a high-precision high-resolution seismic reflection method, high-efficiency method for measurement in the bored hole, coal potentiality assessment system, and so forth. For the development of the seismic reflection method, studies are conducted to properly deal with a situation where there are high-velocity layers at levels shallower than the object coal bed, and a conclusion is reached that quake generation based on the pseudorandom binary sequence code will be the best for the purpose. The system was tested for verification in a producing coal mine. As for measurement in the bored hole, an on-site test was conducted for a geophysical logging system capable of determining the total sulfur content, ash, and the like, and the system was found to supply high-quality data. In developing the coal potentiality assessment system, studies were made about the basic concept of the coordination of the system with the coal GIS (geographical information system) dealing with spatial data and about the functions of the system, and a conceptual design was prepared. (NEDO)

  11. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  12. Fiscal 1997 technological survey report. R and D on micromachine technology (Development of high functional maintenance technology for power station equipment); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    NONE

    1998-03-01

    Activities were conducted in search of micromachine technology for a high functional maintenance system that inspects and repairs abnormal conditions such as cracks in a heat exchanger or a piping system without disassembling it in a power generating station such as a thermal or nuclear power plant. The activities were proceeded in four areas of (1) experimental manufacturing of the system (an inline self-running environment recognizing system, an external inspection system for fine tube group, and a system capable of light internal operation such as welding), (2) R and D on sophistication technology for functional devices, (3) R and D on common basic technologies, and (4) comprehensive investigation and research. In (1), examination of detailed basic specifications was carried out, as were examination of element technologies, experimental manufacturing and operation test of element devices, and performance evaluation. Further, a part of element devices was made on an experimental basis, with the basic functions demonstrated. In the comprehensive investigation and research, a trend in the future maintenance technology in power generating equipment was obtained and pigeonholed. (NEDO)

  13. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  14. Fiscal 1999 achievement report on research and development of industrial technologies. Research and development of synergy ceramics; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

    NONE

    2001-03-01

    Efforts are conducted in the two fields of (1) survey and research and (2) development of technology for evaluating high temperature dynamic corrosion characteristics of heat resistant ceramics. In field (1), a comprehensive survey is conducted, an application study is conducted about high temperature gas separating ceramic membranes, and efforts are made to put to practical use ceramic parts manufactured by a low cost production process. In the application study of ceramic membranes, technologies are developed for a process of manufacturing high temperature gas separating porous ceramic membranes capable of separating and purifying gas emissions and gas ingredients, which involves the development of technologies for improving on gas separation and purification functions, development of technology of providing catalyst support function, technology of porous membrane formation, evaluation of separation characteristics, and so forth. In an application study for ceramic parts manufactured by a low cost manufacturing process, which involves structural ceramics, optimization is accomplished for materials synthesizing technologies by means of mechanical alloying, and cylinder liners are fabricated and evaluated for a natural gas engine made of silicon nitride based ceramics. In field (2), a high temperature dynamic corrosion testing device is built for heat shield coatings. (NEDO)

  15. Fiscal 1998 survey report. Welfare equipment (Development of human friendly care support intelligent equipment / Development of home welfare equipment system); 1998 nendo chosa hokokusho. Fukushi kiki (human friendly kaigo shien chino kiki kaihatsu / zaitaku fukushi kiki system kaihatsu)

    NONE

    1999-03-01

    Since disabled persons increase with a progress of an aging society, while a care power decreases with a decrease in birth rate, development and practical use of the welfare equipment contributing to self-support of aged and handicapped persons, reduction of doctors' or therapists' burdens, and as a result, reduction of medical care costs are desirable. Among them, R and D and practical use are expected of the advanced welfare equipment and system based on human engineering technology contributing to improvement of lives of aged and handicapped persons, and support of nurses and cares of disabled persons. In fiscal 1998, on both human friendly care support intelligent equipment and home welfare equipment system, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. For the former, 'heart disease diagnosis and treatment total support system,' and for the latter, 'body function rehabilitation support system' were surveyed. (NEDO)

  16. FY1999 technological development of wind power generation systems for islands. Development of wind power generation systems in islands; 1999 nendo ritoyo furyoku hatsuden system nado gijutsu kaihatsu. Rito ni okeru furyoku hatsuden system no kaihatsu

    NONE

    2000-03-01

    With an objective of developing wind power generation systems that suit small to medium size islands in Japan, conceptual design was made on a 100-kW class wind mill to satisfy such requirements as no need of large heavy machines, and gust resisting performance. Investigations were performed on sites suitable for demonstration tests thereof. This paper reports the achievements in fiscal 1999. In investigating the site location feasibilities, which took small to medium size islands in Okinawa Prefecture as the discussion objects, environmental investigation, wind condition forecast and investigation, and system linkage investigation were carried out, whereas one point each in three islands were extracted as the promising sites. The system discussion and design called for wind velocity resistance of 80 m/s, system linkage percentage of 40% at maximum, power generation cost of 20 yen per kWh, design life of 20 years, constructability of requiring no large heavy machines, and operation mode of diesel hybrid use. Along with these specifications, conceptual design was performed on the system constituting elements, such as wind mill blades, generators, electric power control devices, and towers. In the blade aerodynamic test, wind tunnel tests were executed by using three types of blade wings. Sample blades were fabricated for the preparation of blade material tests. (NEDO)

  17. Research and development of peripheral technology for photovoltaic power systems. Research and development of redox flow battery for photovoltaic power generation; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo redox denchi no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of redox flow battery for photovoltaic power generation in fiscal 1994. (1) On the production method of electrolyte, silica reduction treatment was attempted to use ammonium metavanadate recovered from boiler as electrolyte of redox flow battery. Silica removal rates more than 90% were achieved by crystallizing V as polyvanadate while keeping molten silica. It was ascertained in minicell experiment that trivalent and quadrivalent V electrolytes produced from recovered V are applicable to continuous charge/discharge operation for one week. (2) On development of battery systems, the relation between battery characteristics and physicochemical properties of carbon fiber electrodes was studied to improve carbon fiber electrodes. The efficiency of 80% was achieved at current density of 160mA/cm{sup 2} by use of layered electrodes, resulting in considerable cost reduction. Performance evaluation operation of the 2kW battery prepared in the last fiscal year was also carried out. 4 figs.

  18. Research and development of peripheral technology for photovoltaic power systems. Development of inverter technology for photovoltaic (PV) system which is connected to the utility grid; Shuhen gijutsu no kenkyu kaihatsu. Fukusu kino tan`itsuka shuhen sochi no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on development of integrated multifunctional peripheral equipment in fiscal 1994. (1) On development of inverters with no transformer, the following study results were obtained. Converter efficiency reached the target of 95.0% by using an improved general purpose IGBT as switching element of main circuit. Distortion factor of output current harmonics achieved 5% in total current distortion factor, and less than 3% in each order harmonic current one. In control of the DC part of output current, the target less than 0.3% was achieved by inserting a capacitor into detection signal circuit and by detection/correction control of current detector offset. Detection level of 100mA was achieved for DC grounding detection by installing a DC grounding detector in the DC input side of inverters. VCCI 1 level was also achieved for EMI measurement. (2) On development of integrated multifunctional peripheral equipment, evaluation test of the prototype equipment of 0.025m{sup 3} in volume and 17kg in mass was carried out. 3 figs., 1 tab.

  19. Research and development of peripheral technology for photovoltaic power systems. Research and development of photovoltaic modules integrated with construction materials (detachable plane panel); Shuhen gijutsu no kenkyu kaihatsu. Kenzai ittaigata module no kenkyu kaihatsu (chakudatsushiki heiban panel)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of photovoltaic modules integrated with construction materials in fiscal 1994. (1) On development of technology for module structures, specifications of the horizontal muntin system module were newly determined in addition to the improved muntin system module, and the prototype pseudo-module integrated with construction material was prepared. The comparison results of the basic performance of both system modules clarified superior waterproofing and module temperature uniformity of the horizontal muntin system. Based on this specifications, integration technology of modules with back metal plates was studied. Formation of the integrated module close to final specifications was ascertained to be possible by use of passivation equipment to irregular form. (2) On development of construction and installation methods of modules, improvement of the waterproofing and workability of both system modules was studied. (3) On the study on practical use of modules, their design and ventilation/cooling structure were studied. 38 figs., 13 tabs.

  20. Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

    NONE

    1982-03-01

    To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

  1. Research and development of evaluation system for photovoltaic power generation system. Research and development of evaluation systems for photovoltaic cells and modules; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation system for solar cells in fiscal 1994. (1) On development of the performance evaluation method for solar cells, data collection, analysis and measurement of atmospheric conditions necessary for outdoor measurement were carried out to improve the measurement accuracy of laminated solar cells. The validity of measurement methods was verified by comparing experimental results with outdoor measurement ones to improve the indoor measurement accuracy by multiple light source solar simulator. Generated energy in solar cell module level was also studied in field. (2) On development of the reliability evaluation method for solar cells, deterioration data were collected and analyzed by long-term exposure test. As a result, it was clarified that Pmax values are directly affected by seasonal change in air mass, and deterioration of solar cells is hardly found after exposure test for one year, showing a stable state. The characteristic recovery experiment of amorphous solar cell modules was carried out, and the accelerated deterioration test method of thin film cell modules was also studied. 2 figs.

  2. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  3. Fiscal 1976 Sunshine Project result report. R and D on solar heat power generation system (R and D on tower solar collection system); 1976 nendo taiyonetsu hatsuden system no kenkyu kaihatsu seika hokokusho. Tower shuko hoshiki system no kenkyu kaihatsu

    NONE

    1977-05-27

    This report describes the fiscal 1976 research result on tower solar collection system for solar heat power generation systems, and summarizes main specifications of the subsystem, equipment and control of the 1,000kW pilot plant. Based on daily and monthly long-time simulation, various programs were prepared for power generation, heat storage and operation rate of equipment, and real arrangements for total simulation were made. The output fluctuation rate less than 1%/min was obtained by studying a control system flexible for drastic fluctuation of solar radiation using the newly prepared dynamic characteristic equation for a steam loop. 10kW solar collection test was carried out using a pancake type heat absorber. Practical basic analysis was made on a heliostat driving system. A cavity type heat absorber was adopted in consideration of cost, operability and heat discharge. Based on thermal characteristics of a heat storage type heat exchanger using molten salt as heat medium, basic experiment was made on a compact latent heat type heat exchanger. Basic studies were also made on reflector, selective absorption surface and heat storage material. (NEDO)

  4. Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

  5. Research and development of evaluation system for photovoltaic power generation system. Survey on research and development of solar cell evaluation system; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Taiyo denchi hyoka system no kenkyu kaihatsu chosa

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on R and D of solar cell evaluation systems in fiscal 1994. The performance/reliability evaluation subcommittee continuously analyzed technical issues and discussed solution measures from the last fiscal year. On development of performance evaluation methods, improvement of measurement accuracy for laminated solar cells is the study issue to be solved. Although laminated solar cells are measured by multiple light source solar simulator, difficult spectrum compensation causes measurement errors. Collection and analysis of data for determining atmospheric conditions, and outdoor measurement experiment under the atmospheric conditions for reference solar light were carried out. The study on incident angle characteristics of laminated solar cells clarified that the deviation from COS characteristics is 1.0% or less at an incident angle of 30{degree}. The study on generated energy in solar cell module level in field clarified that generated energy and generation efficiency are proportional to intensity of solar radiation. 1 tab.

  6. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  7. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei)'. Daiikki kenkyu kaihatsu hyoka

    NONE

    1984-03-30

    The results of the first phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. This project is aimed at development of the resin-based composite materials as light, high-strength and high-rigidity structural materials. Development of the basic techniques for these materials is of high significance, and highly rated. The first R and D phase efforts are directed to synthesis of new skeleton and terminal compounds, and their introduction into the matrices; application/combination of various fiber surface modification techniques; development of the basic techniques for intermediate materials for three-dimensional fabrics, triaxial fabrics and hybrid materials; improvement of the main techniques for a series of molding/processing steps; adoption of new methods; and development of design programs and elementary design techniques. The technical targets of improving functions of each item have been achieved, or bright prospects have been obtained therefor, each involving potentials of functional improvements by developing new functions. It is also considered that the parallel, competitive development and promotion of 7 routes in researches on the matrix resins have brought great effects. (NEDO)

  8. Research and development of evaluation system for photovoltaic power generation system. Research and survey on test and evaluation method for BOS component devices; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. Shuhen gijutsu hyoka system no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of the evaluation method for BOS component devices in fiscal 1994. (1) On the study on requirements of BOS component devices for practical use, the study results on storage battery, inverter, protective device for system interconnection, and effective use means for storage battery were summarized. On the future device technology, it was clarified that the following value added technologies are promising: simple design of inverter circuit, cost reduction by common specification and mass production, and stabilization of voltage and compensation of momentary peak load by combining inverter with small-capacity storage batteries. (2) On the study on the performance test method for BOS component devices, basic characteristic (capacity, efficiency) test, PSOC charge/discharge cycle test, and accelerated life cycle test were performed for 4 kinds of new storage batteries developed by NEDO. The whole characteristic test results satisfied specifications, and long-term cycle test is in promotion for all new storage batteries. 3 figs., 4 tabs.

  9. Research and development of peripheral technology for photovoltaic power systems. Research on engineering methods for cost effective PV installation; Shuhen gijutsu no kenkyu kaihatsu. Tashu secchi koho no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of engineering methods for photovoltaic power system installation in fiscal 1994. (1) On the survey on applicable fields, various application aspects, applicability, and problems on location and legal regulation were continuously studied for railway, river reservation, lake surface and public facility as promising locations after highway in the last fiscal year. The result pointed out relatively easy possibility of PV power generation of nearly 11,700MW except residence and building fields. (2) On installation technology of solar cell arrays, several models based on various installation conditions, construction methods and system configurations were studied, and various application aspects were proposed by combination of simple design conditions. (3) On test and evaluation of the structural design of array racks, wind tunnel experiments were conducted for structure wall, platform shed and highway sound insulation wall. (4) On basic design of various promising systems, the conceptual design of interconnection systems was carried out assuming applications to highway and railway. 7 figs., 3 tabs.

  10. Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

  11. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

    NONE

    1991-05-01

    Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

  12. Survey and research for the enhancement of large-scale technology development 1. Japan's large-scale technology development and the effects; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 1. Nippon no daikibo gijutsu kaihatsu to sono koka

    NONE

    1981-03-01

    A survey is conducted into the effects of projects implemented under the large-scale industrial technology research and development system. In the development of 'ultraperformance computers,' each of the technologies is being widely utilized, and the data service system of Nippon Telegraph and Telephone Public Corporation and the large computer (HITAC8800) owe much for their success to the fruits of the development endeavor. In the development of the 'desulfurization technology,' the fruits are in use by Tokyo Electric Power Co., Inc., and Chubu Electric Power Co., Inc., incorporated into their desulfurization systems. Although there is no practical plant based on the 'great-depth remotely controlled submarine oil drilling rig,' yet oceanic technologies and control methods are being utilized in various fields. The 'seawater desalination and by-product utilization' technologies have enabled the establishment of technologies of the top level in the world thanks to the resultant manufacture of concrete evaporator and related technologies. Eleven plants have been completed utilizing the fruits of the development. In the field of 'electric vehicle,' there is no commercialization in progress due to problems in cost effectiveness though remarkable improvement has been achieved in terms of performance. Technologies about weight reduction, semiconductor devices, battery parts and components, etc., are being utilized in many fields. (NEDO)

  13. Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant); 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu

    NONE

    1981-03-01

    This report summarizes the fiscal 1980 research result on evaluation of elementary technology studies, research on plant technologies, and assessment of profitability for development of the next 10MW class large binary cycle power plant. In evaluation of heat media and heat cycles, selection of heat media and preparation of specimens through document survey, measurement of thermal characteristics, and preparation of pressure-enthalpy charts were carried out for selection of promising media. In evaluation of materials, as the field corrosion test and simulation results on 3 kinds of welding materials, it was concluded that SUS316 is best as material. In evaluation of heat medium turbine, through the test on oil film seal and mechanical seal techniques, various information were obtained. In evaluation of mist-cooling condenser, experiment on the basic unit heat exchanger, and study on the optimum design were carried out. In addition, research on plant technologies, and assessment of profitability were conducted. (NEDO)

  14. Research and development of basic technologies for the next generation industries, 'environment resistance strengthened elements'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'taikankyo kyoka soshi'. Daiikki kenkyu kaihatsu hyoka

    NONE

    1984-03-30

    Research, development and evaluation were performed with an objective of developing environment resistance strengthened elements, with emphasis placed respectively on radiation resistance, heat resistance, and integration degree according to specific requirements in the using environments. The objective for the first term is to develop the basic technology on element structures required to raise the environment resistance, and the methods of testing them. With regard to heat resistant elements, {beta}-SiC single crystal thin films were formed, and a prospect was obtained on using them as the elements. Regarding MOS integrated circuit, bipolar integrated circuit, and GaAs element, points presenting the largest issue in radiation resistance were noticed according to respective elements. Thus, temperature for gate oxide film formation was lowered, element structures were improved, and gate lengths were decreased to enhance the radiation resistance. For the evaluation test technology, a provisional testing method was prepared for the radiation resistance, a prototype in-situ irradiation testing device was fabricated and so was a prototype high-temperature testing device usable up to 500 degrees C. These achievements lead to a belief that the targets for the first term have been achieved. (NEDO)

  15. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

    NONE

    1991-05-01

    For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

  16. Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

    NONE

    1991-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

  17. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  18. Surveys for promoting development of overseas coals in fiscal 1999. Surveys on international coal situation; 1999 nendo kaigaitan kaihatsu kodoka nado chosa (kaigaitan kaihatsu sokushin chosa). Kokusai sekitan jijo chosa

    NONE

    2000-03-01

    Detailed surveys were performed on Britain, Germany and Spain being the major coal producing countries in Europe with regard to a general view on the status of energy demand and supply, the status of demand and supply of coal, business institutions, and related policies in each country. The status of demand and supply of coal, and related policies in the three countries may be summarized as follows: In Britain, the ratio of coal accounted for in the primary energy supply is 18.0% in 1998, and the coal production amounted to 35.5 mill.TCE/year; closure of underground mining coal mines is discussed recently; the congress is deliberating re-introduction of the subsidy system which had been once discontinued; in Germany, the ratio of coals accounted for in the primary energy supply in 1997 was 14% in bituminous coal and 11% in brown coal; the quantities of production of bituminous coal and brown coal in 1998 were 41.8 and 50.6 mill.TCE/year, respectively; the number of mines has decreased because of the unification; the subsidy policy is in continuation; in Spain, the ratio of coal accounted for in the primary energy supply was 13.5% in 1997 and the quantity of coal production in 1998 was 12.5 mill.TCE/year; unification of coal operators has not been advanced as far as in Germany; and the subsidy is provided as in Germany. (NEDO)

  19. FY 1993 Research and development of ceramic gas turbines. Development of methods of testing and evaluating ceramic member bonding techniques; 1993 nendo ceramic gas turbine no kenkyu kaihatsu seika hokokusho. Ceramic buzai setsugo gijutsu no shiken hyoka hoho no kaihatsu

    NONE

    1994-05-01

    Studies are conducted to establish the methods of testing and evaluating applicability of ceramic-metal bonding for ceramic gas turbines, and the FY 1993 results are reported. The program involves measurement of residual stress by the X-ray method and durability tests for the joints of silicon nitride and austenitic stainless steel with copper as the intermediate layer, and analysis and classification of the strength/durability test results obtained until the previous fiscal year by the finite element method, to evaluate applicability of the joining. For the strength characteristics at high temperature, the test pieces tend to lose strength at 400 degrees C and higher, and high-temperature strength as cross-head displacement speed increases. The upper limit of bending strength at room temperature decreases as number of thermal cycles increases. The test pieces subjected to thermal cycles have a higher bending strength at high temperature than at room temperature. The results of the two-dimensional plasticity analysis of the residual stress in the joint by the finite element method are in good agreement with the results by the X-ray method. (NEDO)

  20. Fiscal 1999 research on geothermal energy development promotion. Research report on development feasibility (Strategic survey - nationwide survey); 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Kaihatsu kanosei chosa (senryakuteki chosa zenkoku chosa)

    NONE

    2000-10-01

    Analysis and assessment were conducted for each of promising geothermal regions over large areas so as to contribute to the drafting of survey implementation plans and estimation of the amounts of recoverable geothermal reserves under the geothermal energy development promotion project. In this fiscal year, based on the manual compiled in the preceding fiscal year, studies were made on the six areas, which were the eastern part of Hokkaido, Toyoha-Niseko area, Iburi area, Bandai-Azuma area, Minamiaizu-Nasu area, and the island area. In region 1 in the eastern part of Hokkaido, a 48km{sup 2} was extracted in the vicinity of Mount Musa, with the amount of resources per 1km{sup 2} estimated at 12.34-56.02MWe. In region 2 in the eastern part of Hokkaido, promising geothermal regions I, II, III, and IV were extracted, with the amounts of resources per 1km{sup 2} estimated at 50MWe or more at III and part of IV. In the Toyoha-Niseko area, promising regions I and II were extracted, the amounts of resources estimated at 50MWe or more in both regions. For the Iburi area, it was concluded that there was a probability of not less than 90% that the amount of resources was 50MWe or more and it was proposed that an additional survey be conducted. As for the Bandai-Azuma, Minamiaizu-Nasu, and island areas, need of further surveys was pointed out. (NEDO)

  1. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  2. Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

    NONE

    1991-04-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

  3. FY 1995 report on verification of geothermal exploration technology. Development of fracture reservoir exploration technology (development of seismic exploration); 1995 nendo chinetsu tansa gijutsunado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu) hokokusho

    NONE

    1996-03-01

    This report provides the development of new exploration technology using elastic waves, such as reflection seismic survey, VSP, and seismic tomography, for precisely characterizing subsurface fractures in geothermal reservoirs. In order to investigate and improve the effective data acquisition and analysis methods for detecting a fault type of fractures, an experiment of a seismic tomography method was conducted using wells drilled in the Ogiri geothermal field, Aira-gun, Kagoshima Prefecture. An experiment of propagation characteristics of piezo type underground seismic source in the volcanic field was also conducted as a trend survey of underground seismic sources. The fracture type in the model field was systematically analyzed by measuring the core samples obtained in the demonstration test field through remanence measurement, fluid inclusion measurement, and zircon measurement using test equipment, and by analyzing results obtained from cores and results of seismic tomography obtained from the wells. Based on these results, the effectiveness and practical application of exploration methods using elastic waves were investigated. 80 refs., 250 figs., 49 tabs.

  4. Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

    NONE

    1998-03-01

    Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

  5. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the second phase research and development; Jisedai sdangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzoukei)'. Dainiki kenkyu kaihatsu hyoka

    NONE

    1986-03-31

    The results of the second phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to modification of PAN-based high-strength carbon fibers for aluminum-based FRMs, and also to development of the methods for controlling interfacial reactions at high temperature by modification of the base materials for titanium-based FRMs. For development of carbon fiber-based intermediate materials, the techniques are developed for continuous production of wire preforms of aluminum. For development of molding/processing techniques, the press molding and powder HIP molding techniques are developed to give a planar product of the FRM of titanium alloy reinforced with evaporated filaments of silicon carbide, which shows an average tensile strength exceeding the target level. Also developed are the press and roll molding techniques for the wire preforms of aluminum reinforced with silicon carbide fibers, the planar product therefrom showing a tensile strength of at least 99% of the base material. It is concluded that the objectives of the second-phase project are almost achieved. (NEDO)

  6. Fiscal 1999 geothermal development promotion survey. Development potentiality survey - Strategic survey/nation-wide survey (Report on Hokkaido region); 1999 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa - senryakuteki chosa zenkoku chosa (Hokkaido chiiki hokokusho)

    NONE

    2000-08-01

    For the effective implementation of the survey, an analysis was conducted into areas expected to be successfully developed for geothermal energy, and promising areas and prioritized survey areas were selected. Data then in existence were collected at the Doto district 1, Doto district 2, Toyoha-Niseko district, and the Iburi district and subjected to reanalysis, and a wide area geothermal system conceptual model was built. Using the model, development-promising areas were extracted, the amount of resources was assessed, and an optimum survey program was prepared. One promising area was selected in the Doto district 1, four in the Doto district 2, two in the Toyoha-Niseko district, and one in the Iburi district. As prioritized survey areas, Musadake was selected in the Doto district 1; Yoichidake, Yunosawa, and Takinosawa in the Toyoha-Niseko district; and Raibadake in the Iburi district. A Monte Carlo analysis was conducted, and the result indicated that Musakake had 93-121MWe in resources of which 55MWe would be exploitable with a probability of not less than 90%. (NEDO)

  7. Report on fundamental survey on developing coal resources in fiscal 1999. Survey and development of new exploration technology (exploration of shallow land area beds); 1999 nendo sekitan shigen kaihatsu kiso chosa hokokusho. Shintansa gijutsu chosa kaihatsu (rikuiki senso tansa)

    NONE

    2000-03-01

    This paper describes the survey and development of new coal exploration technology applied in the NSW State of Australia. It is intended to develop a coal resource assessment method with high accuracy using the reflection method seismic exploration, assisted by other physical exploration methods. The Caroona area has a Permian period ground bed distributed, in which multiple number of coal layers exist. The ground bed is covered with sedimentary layers of the Triassic period inconsistently, and this Triassic period system is covered by volcanic rocks of the Jurassic period inconsistently. Faults are going through the coal beds in their upper or lower layers at locations having soft rock beds. Existence of the faults was estimated by seismic exploration using the two-dimensional reflection method, assisted by the result of the physical logging. The results were unified with the result of test drilling to identify the summary of the latent basset lines. Furthermore, the seismic exploration using the three-dimensional reflective method capable of high-level imaging of underground structures was applied to coal beds existing in depths less than 480 m. Multiple number of local and small-scale sinking were detected with time difference of 5 ms and depth conversion to 7 m. Locations, runs, and inclination were interpreted also on faults having small fall which cannot be detected by the two-dimensional method. The three-dimensional method was found capable of identifying micro structural changes and fault runs that cannot be tracked by the two-dimensional method. (NEDO)

  8. FY 1991 Research and development project for large-scale industrial technologies. Report on results of R and D of superhigh technological machining systems; 1991 nendo chosentan kako system no kenkyu kaihatsu seika hokokusho. Chosentan kako system no kenkyu kaihatsu

    NONE

    1992-03-01

    Described herein are the FY 1991 results of the R and D project aimed at establishment of superprecision machining technologies for developing machining technologies and nano-technologies aided by excited beams. The researches on the superprecision machining technologies involve design and development, on a trial basis, of the totally static pressure type positioning device, for which automatically controlling drawing is adopted to improve its rigidity. The researches on the surface modification technologies aided by ion beams involve scanning the ion beams onto the metallic plate to be provided around the glass substrate. The results indicate that the secondary electrons generated can be used to control charge-up. In addition, part of a 30cm square glass substrate is modified by implantation of the spot type ions of high current density, and the modified portion is used to produce a thin-film silicon transistor. The researches on superhigh-technological machining standard measurement involve improvement of precision of the system aided by a dye laser, which attains a precision of 0 to 30nm in a 0.1m measurement range. (NEDO)

  9. FY 1998 annual report on the development of fuel cell power generation techniques. Research and development of solid electrolyte fuel cells (research results); 1998 nendo nenryo denchi gijutsu kaihatsu. Kotai denkaishitsugata nenryo denchi no kenkyu kaihatsu

    NONE

    1999-03-01

    Described herein are the FY 1998 research and development results of solid electrolyte fuel cells. For R and D of the tubular type cell by the wet processing technique, the tests are conducted to evaluate the initial performance and long-term durability for continuous operation of the single tubular cell. For development of the several-kW class modules, computer-aided simulations are conducted. For R and D of material and substrate techniques, the thermal cycle characteristics, cell characteristics and stress of the cell modules are evaluated, in order to evaluate their reliability. The thermal cycle test results indicate that performance of the single-stage cell is unaffected by the thermal cycles. It is found by the stress evaluation that use of the separator plate having a higher thermal expansion coefficient than the electrolyte plate and use of the sealant having a thermal expansion coefficient close to that of the electrolyte plate are effective means to reduce stresses. For the research to reduce costs of the cell materials, their chemical, mechanical and thermal characteristics are evaluated. For the system research, the areas for which the compact systems are suitable and their optimization are studied. (NEDO)

  10. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    NONE

    1997-03-01

    The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

  11. Fiscal 1993 achievement report on next-generation industrial structure technology (Advanced materials for extreme environments - Development of methane fueled aeroengine); 1993 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Methane nenryo kokukiyo engine no kaihatsu

    NONE

    1994-03-01

    Efforts were exerted to develop advanced materials for use under extreme environments, which were intermetallic compounds and fiber reinforced intermetallic compound composite materials excellent in heat resistance, specific strength, oxidation resistance, or the like. For the development of intermetallic compounds, efforts were made to develop Ti-Al-X (X=metal) high specific strength intermetallic compounds and Nb-Al-X (X=metal) high melting point intermetallic compounds. Ternary phase diagrams were prepared and the effect of added elements on basic characteristics was investigated. Basics of element technologies (texture control, melting, casting, and isothermal rolling) for manufacturing panel materials were studied and, in the case of Ti-Al-X systems, Ti-Al thin panels were fabricated. In the case of Nb-Al-X systems, items were experimentally fabricated by casting in an effort to study precision casting technology optimization. For the development of composite materials, efforts were made to develop SiC based and SiMC (M=metal) based fibers, and studies were carried out to complex them with Ti-Al based matrices. (NEDO)

  12. Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a technology to measure inside of wells (Development of a fracturing technology); 1980 nendo koseinai sokutei gijutsu no kaihatsu seika hokokusho. Fracturing gijutsu no kaihatsu

    NONE

    1981-03-01

    This paper describes the achievements in fiscal 1980 in developing a technology to measure inside of geothermal wells, and of fracturing (to achieve enhancement and regeneration of well performance). Design and fabrication were completed on the in-tunnel sensor for a neutron/density logger. The sensor withstood use at a temperature as high as 275 degrees C. In logging and reservoir evaluation field tests, reliable data were derived even at a depth of 1,800 m and a temperature of 250 degrees C. Characteristics of response of radioactivity logging (neutron and density logging) to different igneous rocks were investigated by using rock blocks. For the fracturing facilities, improvements were given on transportation performance and installation workability of the preliminary observation device, by utilizing the experience obtained in the previous fiscal year. A composite (divided into two units) centrifugal multi-stage pumping device was developed so that a water injection test can be performed in a wide capacity range according to the intended wells, where nearly satisfying performance was derived. For the fracturing technology, in order for even small test pieces to be capable of evaluating fracture tenacity accurately with consideration on nonlinear behavior of rocks, elasto-plastic fracture tenacity tests were carried out with AE measurement being performed simultaneously. The paper also describes studies on fracturing fluids. (NEDO)

  13. FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

    NONE

    2001-03-01

    Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

  14. Verification survey of geothermal exploration technology, etc. Report on the result of the developmental research on the development of the fracture type reservoir exploration method; Chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu kenkyu kaihatsu seika sokatsu hokokusho

    NONE

    1997-03-01

    For the purpose of grasping fracture groups forming geothermal reservoirs with accuracy, the development of the fracture type reservoir exploration method has advanced the technical development of exploration methods of seismic wave use, electromagnetic induction use, and micro-earthquake use. This paper summarized main results of the development and problems to be solved in the future. In the development of the seismic wave use exploration method, the high accuracy reflection method using seismic wave, VSP and seismic tomography were adopted to the geothermal field, and technology effective for the exploration of fracture type reservoirs was developed. In the development of the electromagnetic induction use exploration method, the array CSMT method which can measure multiple stations along the traverse line at the same time was developed with the aim of grasping effectively and accurately fracture groups forming geothermal reservoirs as changes of resistivity in the shallow-deep underground. In the fracture group forming geothermal reservoirs, micro-earthquakes are generated by movement of thermal water and pressure variations. In the development of the micro-earthquake use exploration method, developed was the micro-earthquake data processing and analysis system (MEPAS). 179 refs., 117 figs., 28 tabs.

  15. FY 1999 achievement report on the development of high performance boilers. R and D on high performance industrial furnaces, etc.; 1999 nendo koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    NONE

    2000-03-01

    This project started in FY 1993 to survey the actual state of industrial use boilers. Based on the results of the survey, in fiscal 1995, 1996 and 1997, no improvement of the present technology which has limits, but the development was made of the oxygen combustion and element technology which are factors for heightening boiler performance with a new idea first in the world. In fiscal 1998, a target for the overall thermal efficiency of 105% was settled by testing a pilot plant where the element technology was integrated into the small once-through boiler, flue/smoke tube boiler, water tube boiler, etc. In fiscal 1999, the target of the overall thermal efficiency of boiler was reached by a pilot plant test to clarify combustion characteristics, heat transfer characteristics, environmental characteristics, etc. Further, effects of energy saving were increased by the adoption method of oxygen supply equipment. Concretely, an overall boiler efficiency of 105.73% exceeding the targeted value of 105% was achieved at a pilot plant of actual scale, by concentrating the results of each of the element technologies such as 'oxygen combustion,' 'condensation type flue gas heat exchanger,' 'high performance combustion control device,' and 'rapid rotating auxiliary machine.' (NEDO)

  16. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  17. Report on 1981 research result on the R and D of superlattice element; 1981 nendo chokokoshi no kenkyu kaihatsu

    NONE

    1982-03-01

    Development of basic technology was conducted on a superstructure lattice element. With an objective of developing a molecular beam epitaxy (MBE) method, which is the basic technology for preparing the superstructure lattice element, the development of silicon clean surface preparing technology was performed, as were the development of molecular beam source, the development of two-dimensional analytical program for designing the element, etc. For the clean surface, comparison was made on various methods, developing a method capable of making a clean surface usable for the MBE fully by a low temperature process that had been non-existent. This was a low temperature thermal etching method which jointly uses a chemical process and a low warmth process. In the molecular beam source, it was found that a large size was necessary for the purpose of improving the purity of the molecular beam and also the characteristics of an epitaxial film, so that a large molecular beam source was developed. A conventional two-dimensional analytical program was improved and developed for the purpose of designing the superstructure lattice element and clarifying the characteristics. By applying the result to the analysis of the motion of the element with impurities doped in the manner of a superstructure lattice, the effectiveness was confirmed of this analytical method. (NEDO)

  18. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  19. FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

    NONE

    1997-03-01

    Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

  20. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of high-reliability CdS/CdTe solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    NONE

    1999-03-01

    Cost reduction for the above-named solar cells is the aim of this effort. On the basis of the results of past studies, a technology is established of fabricating a thin CdS film by subjecting a CdS film to organometal pyrolysis, and this brings about a decrease in photoabsorption loss in the range of waves shorter than 500nm and a decrease in in-film reflection loss for an increase in short-circuit current density. A proximity sublimation method is used for CdTe film fabrication, which improves on film quality and film adhesion. These efforts result in the achievement of a conversion efficiency of 16.0% which is the highest in the world. Studies are promoted in a process nearer to the ultimate form, and a 30cm times 60cm large CdTe solar cell is fabricated on the basis of a patterning technique, and the product attains a conversion efficiency of 9.8%. In fiscal 1998, studies center about the establishment of a film fabrication process for a medium-are substrate and about the enhancement of its conversion efficiency, and facilities capable of dealing with large-area substrates are introduced and operated. In a typical achievement, a CdTe solar cell is experimentally fabricated in a process which is wholly under normal pressure, and the product with an aperture area of 1376cm{sup 2} exhibits a conversion efficiency of 10.5% according to JQA (Japan Quality Assurance Organization). (NEDO)

  1. Achievement report for fiscal 1997 on developing practical application technology for photovoltaic power generation systems under the New Sunshine Project. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, and development of technologies to manufacture new type amorphous solar cells; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, shingata amorphous taiyo denchi no seizo gijutsu kaihatsu

    NONE

    1998-03-01

    Development will be made on high-performance a-solar cells as part of developing practical application technology for a-solar cells for electric power use. Development will be also made on a low-cost process technology. This paper describes the achievements attained during fiscal 1997. Quality improvement has been realized by using a high RF power hydrogen dilution process on a-Si films for front cells of lamination type cells. Four times faster film forming speed was obtained even by using the VHF plasma CVD process, with film quality equivalent to those made by using the conventional RF process maintained. By optimizing the light enclosing construction, the short circuit current was enhanced by over 20%. Discussions were given on forming homogenous a-Si films by optimizing the conditions for forming films on large-area substrates, which resulted in forming film of 30 cm times 40 cm size with good homogeneity at a film forming speed three times faster than the conventional speed. A surface electrode was formed successfully with good uniformity on a substrate with a size of 60 cm times 90 cm. Productivity greater by over three times the conventional productivity was achieved in patterning of transparent electrodes by using high-output laser. Simultaneous and collective patterning and very small and long size collective patterning were realized in a-Si film selection patterning by using the plasma CVD process. (NEDO)

  2. Development of micro solar charger with blocking relay; Gyakuryu boshi relay wo oyoshita kogata solar judenki no kaihatsu

    Nanno, I.; Matsushita, Y. Oka, S. [Omron Corp., Kyoto (Japan)

    1997-11-25

    Heavy-current tiny-scale solar charger is tentatively built, equipped with a function of preventing overcharge and countercurrent in case of charging storage batteries using solar cells. Incorporated into this solar charger are a countercurrent prevention relay system, a low loss current detection system, and a MOSFET parallel connection, which allow the solar charger to be designed small in size in the presence of an increase in heat due to circuit loss. In the countercurrent prevention relay system, the countercurrent prevention diode is bypassed by MOSFETs when too large a current is generated. In the low loss current detection system, currents are detected by use of the ON resistance of the MOSFETs for the prevention of overcharge. In the MOSFET parallel connection, MOSFETs are connected in parallel for a decrease in the ON resistance. The tentatively built charger is then subjected to a performance evaluation test outside the building, and the test is carried out by measuring the temperatures of the MOSFETs and the air. As the result, it is found that the temperature of MOSFET junction of the 12A tiny-size solar charger is approximately 42.5 degC at the highest, low enough to clear the requirements. 4 refs., 7 figs., 4 tabs.

  3. Study on evaluating method for earthquake resisting performance of steel piers; Kosei kyokyaku no taishinsei ni kansuru kenkyu kaihatsu

    Isoe, A.; Hashimoto, Y.; Morimoto, C.; Sakoda, H.; Ishige, T.; Yoshikawa, T.; Kishida, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1998-12-20

    After the shock of Hyogoken Nanbu Earthquake in 1995, protection against level 2 earthquake becomes important subject for civil structures. Subsequently plastic design methods for steel piers have been studied and rapidly introduced. The authors developed a method to evaluate the earthquake resisting performance of a steel pier with a single mass model. This model is useful for design because of its simplicity but on the other hand it can not consider the effects of piers` interaction in space. To include this effect in an analysis a simple 3 dimensional calculation model of box-column pier is developed. (author)

  4. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

  5. New ion exchange resin operation for downstream of bioprocess; Hakoeki chokusetsu shorigata ion kokan jushi sosaho no kaihatsu

    Ito, H.; Kusunose, Y.; Yokoyama, M. [Ajinomoto Corp., Tokyo (Japan). Tech. and Engineering Laboratories

    1999-09-10

    A new ion exchange resin operation system which can treat fermentation broth without any pretreatment is studied. In a conventional fixed bed column pre-treatment such as membrane or centrifugal separation is required in order to prevent the clogging of bacteria in the resin layer inside. However these processes require higher capital investment and lower the yield. The new method solves these problems by treating ion exchange resin as slurry. No problem is observed in pilot scale experiments using lysine fermentation broth. The bacteria do not clog the resin phase, and elute is not contaminated, even if the bacteria concentration of the feed fermentation broth is very high (10 vel %). In addition, it is found that the amount of washing water in the new method is less than that of the conventional method. A simple numerical simulation model is also proposed and evaluated. The numerical value expresses good agreement with the experimental value, and it is proved that this model can be used for optimization of process design. (author)

  6. Fiscal 2000 achievement report. Welfare technosystem research and development (Ube); 2000 nendo walfare technosystem kenkyu kaihatsu (Ube) seika hokokusho

    NONE

    2001-03-01

    Efforts continue to develop welfare nursing equipment for helping persons in need of nursing care or handicapped persons who live an independent life. Efforts are exerted in three fields for developing (1) a motor driven wheelchair in which the occupant feels as if driving a car, (2) an online cardiac function monitoring system using a cardiac sound sensor, (3) an automatic pressure belt for patients of postural low blood pressure, (4) and a seated position aiding and stabilizing device for workers with legs not fully useful. In field (1), the steering wheel, brake, and driving system are contrived so that the occupant may easily drive the wheelchair as if in an automobile driver's seat. In field (2), a device is developed to monitor and examine the heart rate and respiration rate, for which a cardiac sensor has to be installed on the water bed or an air mattress. In field (3), a computer controlled automatic pressure belt is developed for patients of myelopathy or cerebrovascular disease. In field (4), a work assisting device is developed to help seated workers with leg troubles. (NEDO)

  7. Experimental development of a torsion arc blade type horizontal axis windmil; Nejire enko yokugata suihei jiku fusha no kaihatsu

    Kojima, N. [Meiji Univ., Tokyo (Japan). Faculty of Scince and Technology

    1996-05-31

    To get more wind energy, longer rotating blades and higher towers of windmills are required. Therefore, the location of windmills is limited and the initial cost gets higher. In this study, a small size windmill which can generate electricity even in a city was developed and tested. A torsion arc blade type horizontal axis windmill was designed and the blade form, number and degree of distortion were investigated. Based on the results, a small windmill was made, rotation and generation tests were carried out and it was confirmed that the windmill could be used as a small scale wind power generation. The windmill is of simple construction having 6 arc blades and no high tower is required. This paper consists of 6 sections, i.e. Introduction, Windmill model, Tested windmill, Test facility and method, Test results and consideration, and Postscript. 2 refs., 18 figs., 1 tab.

  8. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  9. Development of environmentally friendly universal controller. Data and materials; 1998 nendo kankyo taio universal controller no kaihatsu seika hokokusho. Shiryohen

    NONE

    1999-05-01

    Research and development was carried out for an 'environmentally friendly universal controller (UC)' which would be 'user-friendly and energy-saving' when used with electrical home appliances, and data and materials on them were compiled into this volume. It covers the specifications (Versions 0.6 and 0.51) of a newly developed two-way controller protocol, the specification (Version 0.1) of two-way remote control IrDA-C communication unit hardware, an infrared communication protocol IrDa Control, and the like. It also accommodates information collected through surveys of technological trends as reflected in technical literature, Internet home pages, catalogs, and the like, concerning the user-friendliness of electrical home appliances, remote control, domestic consumption of electric power, and the like. Also covered is the result of surveys of patents involving environmentally friendly UC related technologies, namely, Japanese patents (from applications made in 1979 through disclosures made in 1998) and U.S. patents (registrations made in 1982 and thereafter). Furthermore, it contains the result of surveys of actualities of domestic use conducted for the purpose of clarifying the effect of environmentally friendly UC introduction, how such UCs are being accepted by the public, and the conditions that should be satisfied for their popularization. (NEDO)

  10. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  11. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    NONE

    2000-03-01

    The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

  12. FY 1998 R and D project on industrial science technology; 1998 nendo ryoshi kino soshi no kenkyu kaihatsu seika hokokusho

    NONE

    1999-03-01

    The R and D on quantum functional devices (QFDs) were conducted, and the FY 1998 results were summed up. In the comprehensive survey on QFDs, the following were carried out for the efficient R and D promotion: R and D progress state survey/problem extraction/analytical study, technical trend survey, overseas survey ordered from overseas supplier, common basement technology study, etc. In the R and D on technology for QFDs, integration of multivalued logical devices using tunneling control functional devices, integration of logical memory devices using quantum levels, integration of quantum band combination-type multi-functional devices, silicon insulating film tunnel memory devices, assembly quantum dot functional memory, quantum wave switching functional devices, integration of single electron logical devices, integration of CMOS combination-type single electron devices, etc. Moreover, in the development of the basement technology of single electron devices, technology to construct element devices using quantum functions, basement technology of single electron device integration devices, architecture of single electron device information processing circuit system, etc. (NEDO)

  13. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

    NONE

    2001-03-01

    Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

  14. Fiscal 2000 achievement report. Welfare technosystem research and development (Niihama); 2000 nendo walfare technosystem kenkyu kaihatsu (Niihama) seika hokokusho

    NONE

    2001-03-01

    Efforts are made to develop welfare equipment systems for helping people needing care lead an independent life. In collecting data on the transfer of patients and carrying out research and development in this connection, activities are conducted to develop (1) a transfer wheelchair and a transfer aiding wheelchair, (2) a simplified transfer type toilet, and (3) a tilt mechanism installable on a standard wheelchair. Under item (1), a wheelchair and an auxiliary wheelchair enabling the transfer of a person who cannot move without help between a wheelchair and an automobile are experimentally built. Under item (2), a simplified transfer type toilet to which a single attendant can easily guide the patient from the bed is developed. Under item (3), a tilt mechanism is developed, installable on a wheelchair to recline the same for the aged person to assume a comfortable attitude. In the development of a portable character reading device, a finger tip reader was experimentally manufactured for reading Japanese characters. (NEDO)

  15. Development of ethylene direct oxidation process acetic acid new manufacturing method; Echiren jikisanho sakusan shinseizoho no kaihatsu

    Sano, Ken' ichi; Nishino, Hiroshi; Iizuka, Yukio; Suzuki, Toshiro; Sasaki, Koji [Showa Denko Corp., Tokyo (Japan)

    1999-03-05

    Though existing acetic acid manufacturing which made the ethylene to be the starting material was two steps oxidation method of the via acetaldehyde, this study persons developed the new manufacturing method by the ethylenic direct oxyacid. In system of reaction, the following were realized by the development of palladium/heteropolyacid system composite catalyst: High activity and selectivity. In the purification system, the process of becoming, when the water consequentially forms azeotrope for the separation between acetic acid and extracting agent that extracting agent of alkyl acetate was done, that it was used and extracted, was developed. In the equipment material aspect, it is sufficient as a 316 stainless steel unlike other acetic acid manufacturing method. As an equipment scale, it has made to be the optium size for 5-200 thousand t/year, and that the location that it is more small-scale than methanol, carbonylation method and approaches the consumption ground is possible are features. The industrial plant for 100 thousand t/year based on this study carries out business operation in Oita since November, 1997. (translated by NEDO)

  16. Introduction of research and development in Image Information Science Laboratory; Image joho kagaku kenkyusho ni okeru kenkyu kaihatsu no shokai

    NONE

    1999-10-10

    This paper introduces research and development at the Image Information Science Laboratory. This is a joint industry-university research institution for the purpose of making a computer recognize human non-language information, expressing and transmitting it, with the research conducted at two centers, Kanto and Kansai. The following studies are being made at the Kansai research center: man/machine interface making natural communication possible between a man and a machine, with emphasis placed on visual information; sensing technology for measuring human activity, technology for analyzing/forming human sensitivity, and technology of expression; technology by which a work is done by a computer in place of a man and reproduced on the computer, with the skill transferred to a man; and development of a spatial expression media system such as a three-dimensional display device. The Tokyo research center is participating in the following projects: committee for promoting joint industry-university research and development of virtual reality (VR); joint industry-university research, development and implementation project of advanced VR; survey on physiological psychological effect in VR system and the like; and research and development of human media. (NEDO)

  17. Development of magnesium semi-solid injection molding; Magnesium han`yoyu shashutsu seikei gijutsu no kaihatsu

    Sakamoto, K; Sakate, N; Ishida, K; Yamamoto, Y; Nishimura, K [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    Magnesium semi-solid injection molding is safety and clean process. We have investigated influence of molding conditions on mechanical properties and dimension accuracy of products by semi-solid injection molding. As a result it was proved that the accuracy of products by this process is superior to die casting. This advantage as well as better mechanical properties can be utilized for net shape molding of some automobile parts. 4 refs., 8 figs., 3 tabs.

  18. Development of regeneration technique for diesel particulate filter made of porous metal; Kinzoku takotai DPF no saisei gijutsu no kaihatsu

    Yoro, K; Ban, S; Ooka, T; Saito, H; Oji, M; Nakajima, S; Okamoto, S [Sumitomo Electric Industries, Ltd., Osaka (Japan)

    1997-10-01

    We have developed the diesel particulate filter (DPF) in which porous metal is used for a filter because of its high thermal conductivity and a radiation heater is used for a regeneration device because of its uniform thermal distribution. In the case high trapping efficiency is required, filter thickness should be thick. The thicker filter has a disadvantage of difficulty in regeneration because of the thermal distribution in the direction of thickness. In order to improve regeneration efficiency, we designed the best filter-heater construction which achieves uniform thermal distribution by using computer simulation and we confirmed good regeneration efficiency in the experiment. 4 refs., 14 figs., 1 tab.

  19. Development of three-dimensional pipe bending technology; Pipe zai no sanjigen mage kako gijutsu no kaihatsu

    Takeuchi, K; Takeda, S [Aisin Seiki Co. Ltd., Aichi (Japan)

    1997-10-01

    Recently, automotive parts uses move resin products or pipe-like products in order to achieve high quality or light weight. Additionally, the shape of automotive parts becomes more complicated. The rotary stretch bending method, although it is most popular method of bending a pipe, has some problems, such as a bending radius is limited due to use of bending mold, a thickness of an outer side of a bending portion is thinner, and a product is scratched easily during manufacturing. We have developed a three dimensional pipe bending process using a floating expanding plug and confirmed that this method can solve the above problems. 2 refs., 9 figs., 3 tabs.

  20. Measurement improvements of heat flux probes for internal combustion engine; Nainen kikan ni okeru netsuryusokukei no kaihatsu to kento

    Tajima, H; Tasaka, H [Miyazaki University, Miyazaki (Japan)

    1997-10-01

    In heat flux measurement in engines, material properties of a heat flux probe and numerical prediction of those influence have been discussed rather than practical measurement accuracy. This study featured the process for the quantitative examination of heat flux probes. Although the process required direct comparison among all the probes and additional measurements in a constant volume bomb, precision of heat flux measurement was greatly improved so that the essential characteristics of heat transfer in engines can be detected. 9 refs., 8 figs., 1 tab.

  1. Development of a high performance carbon fiber fabrics. Koseino tanso sen'i orimono no kaihatsu

    Nishimura, A.; Honma, K.; Matsui, J. (Toray Industries Inc., Tokyo (Japan). Composite Materials Research Lab.)

    1993-01-15

    On setting a position as an intermediate material for the advanced composite materials (ACM), carbon fiber fabrics is required to improve its optimization of the fiber orientation and structure of the fabrics under consideration on anisotropy of the composite materials in order to establish their higher performance. And, it also becomes important to establish energy conservation in higher order of processing containing their molding in order to make great strides the application range of the ACM. The ACM is generally a laminate comprising of some sheet-like, thin substrates arranged the reinforced fibers in one- or two-dimensional direction. As it has some high performance, mechanical properties because of the fiber orientation in a plane direction, its mechanical properties among the layers are determined by adhesion and its strength between the fibers and the resin and weak without any fiber reinforcement in its layer direction. As a method of its improvement, development of a fabrics or twisted yarns having the fibers oriented in three-dimensional direction is proceeding, but they have some limits in their fiber orientation yet and inferior productivity. A technical development of stitched preform is now executed as a low cost molding process. 9 refs., 7 figs.

  2. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of high-reliability CdTe solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Koshinraisei CdTe taiyo denchi mojuru no seizo gijutsu kaihatsu)

    NONE

    2001-03-01

    Research and development was conducted for reliable CdTe solar cell modules, large in area and high in efficiency. In the study of large-area CdS thin film fabrication, a conversion efficiency of 12.5-14.2% was achieved in a cell in a large-area substrate using a mist method-aided process of continuous CdS film fabrication. In the study of large-area CdTe thin film fabrication, the optimization was studied of the base-forming CdS film fabrication conditions and of the CdTe film fabrication conditions in a method using a CdTe powder processed by dry kneading, and a conversion efficiency peak was found to exist when the CdS film thickness was in the range of 700-900 angstrom. In the fabrication of large-area submodules, a large-area substrate was taken up, and TCO (transparent conducting oxide) film was fabricated by the mist method, CdTe film by the normal pressure CSS method, electrodes by the screen printing method, and CdTe film patterns by the blast method. As the result, a conversion efficiency of 11.0% was achieved. In a cost estimation for large-area CdTe solar cell modules, 140 yen/Wp (conversion efficiency: 11.0%, annual production: 100 MW) was obtained. (NEDO)

  3. Development of electric power transmission line anomaly approaching alarm system. Sodensen ijo sekkin keiho sochi no kaihatsu

    Kusaba, Masaro; Tabata, Takatoshi; Miyazaki, Shusuke [Kyushu Electric Power Co., Inc., Fukuoka (Japan)

    1989-03-30

    In order to plan preventive measures from the occurrence of electric power transmission line accident, a power transmission line anomaly approaching alarm system was developed to automatically alarm the operators and surveillants. The surveillance system, composed of camera, surveillance unit proper and alarm receiving portion, generates alarm and indicate hazard to the operators, when animal invades a hazardous area designated on the monitor. Wireless telegraph for the alarm transmission use used frequency around a 322MHz band with the Radio Ray law and preventive measures from noise, taken into consideration. The prototype is characterized by unnecessary ancillary fitting to the surveillance object, rare erroneous operations and high reliability. While the hazardous area can be simply designated, changed and released, as made by volume on the control panel. It is moreover easy to designate, as done by confirming the surveillance object on the display. It is also possible in multidimensional surveillance and easy to use on site. 7 figs.

  4. Radio telemeter system for pressure observation of unifixed point. Futeiten atsuryoku kanshiyo musen telemeter system no kaihatsu

    Yamaguchi, E; Kinoshita, T; Nagao, J [Seibu Gas Co. Ltd., Saitama (Japan)

    1991-10-10

    The radio telemeter system was reported which was developed to monitor gas pressures at unfixed terminal points moving along with the progress of gas calorie conversion from coal gas to natural one. The system was composed of a center system and monitor system to monitor integrally terminal pressures, and terminal systems attached to governors at terminal points of each gas supply area on a medium pressure supply network. The data collected by the terminal systems were transmitted to the center system through a wireless communication system. For efficient and error-free transmission, a hagelbarger code was used because of its bit error correct function by calculation, and a noise-free delayed detection method and rapid two-way retry method were also adopted. Packet and polling communication systems were adopted for data transmission, and batch transmission was also adopted where the data stored automatically in the event of a failure are transmitted in a lump at restarting. 1 ref., 6 figs., 2 tabs.

  5. Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

    Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

    1992-08-25

    A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

  6. Development of nickel-hydrogen battery for electric vehicle; Denki jidoshayo nickel-suiso denchi no kaihatsu

    NONE

    1997-03-01

    Research and development of battery, a main part of electric vehicle, have been promoted. Various batteries, such as lead battery, nickel-cadmium battery, nickel-hydrogen battery, lithium ion battery and so on, have been investigated for electric vehicles. Among these, nickel-hydrogen battery is superior to the others from the points of energy density, lifetime, low-temperature properties, and safety. It is one of the most prospective batteries for electric vehicle. Research and development of the nickel-hydrogen battery with higher energy density and longer lifetime have been promoted for the practical application by Tohoku Electric Power Co., Inc. This article shows main performance of the developed nickel-hydrogen battery for electric vehicle. The nominal voltage is 12 V, the rated capacity is 125 Ah, the outside dimension is L302{times}W170{times}H245 mm, the weight is 25.5 kg, the energy density is 60 Wh/kg, the output density is 180 W/kg, and the available environment temperature is between -20 and 60 {degree}C. 1 fig., 1 tab.

  7. New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

    NONE

    2001-03-01

    Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

  8. Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

    NONE

    2001-03-01

    Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

  9. Fiscal 2000 achievement report. Welfare technosystem research and development (Sapporo); 2000 nendo Welfare technosystem kenkyu kaihatsu (Sapporo) seika hokokusho

    NONE

    2001-03-01

    Activities are conducted on system technologies for ensuring comfortable living circumstances and thereby helping aged or handicapped people live independently in snowy cold regions. The research and development efforts center about the three fields of (1) in-house systems to help aged or handicapped people live an independent life, (2) in-home care equipment systems suitable for advanced welfare oriented residences, and (3) user interface controllers to improve on operating sensation in a motor driven wheelchair. In field (1), studies involve the development of low floor residences for snowy cold regions, improvement on entrances for independent residences helping the inhabitants lead an independent life, and functionally excellent designs for handrails for steps, stairs, or bathrooms. In field (2), surveys are conducted concerning design improvements and their acceptability relative to a universal welfare equipment controller, optimum sound that welfare equipment alarms should produce, and transfer devices. In field (3), studies are made about motor driven wheelchair controllers. (NEDO)

  10. Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

    NONE

    1997-03-01

    In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

  11. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    NONE

    1999-03-01

    A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

  12. Achievement report on developing inverse manufacturing system in fiscal 1998; 1998 nendo inverse manufacturing system no kaihatsu seika hokokusho

    NONE

    2000-03-01

    Research and development has been performed on a circulating type production system, or an inverse manufacturing system, to minimize the environmental load in the entire life cycle of industrial products from design to manufacturing, maintenance, recovery, and re-utilization. In developing the recycling information system, discussion and extraction were executed on the data to be exchanged between manufacturers and users in the inverse society. A new individual parts history control system was developed. In developing the recycling processing system, a prototype system was evaluated by using hypothetical data, wherein the possibility of improving the recycling processing efficiency and reducing the cost was verified. In addition, trial design was made on a recycling processing plant in consideration of the cost effect to get the future plant image. In fabricating the inverse manufacturing products, a prototype concept model was made for information terminal devices. Development was performed on such elementary technologies as the easy-to-disintegrate structure technology, self-integration connecting structure and environmental hysteresis detection system. (NEDO)

  13. Development of ultra low dew-point clean air generator; Cho tei roten seijo kuki hassei sochi no kaihatsu

    Nishimura, H.; Okamura, N. [Takasago thermal Engineering Co., Ltd., Kanagawa (Japan)

    2000-05-10

    To reduce the manufacturing cost of semiconductors, some systems have been proposed that use a cheap and high purity Clean Dry Air (CDA). CDA can reduce process step such as wafer cleaning, because CDA flow in stocker prevents the wafer surface from adsorbing of moisture and organic impurities. We have already optimized a two-stage rotary dehumidifier and have conducted a study of methods for cheaply manufacturing air that has a low dew-point of -70 degree C to -50 degree C. We have further developed the method in which a dry dehumidifier is used, and developed an ultra low dew-point air generator. The air generator is a three-stage rotary dehumidifier in which a further stage is added to the two-stage rotary dehumidifier. The main component of the rotors is metal silicate. The air generator can supply dry air with a dew-point of -110 degree C. or less, in which the concentration in all gaseous contaminants is far below 1 ppb. We made a trial calculation of the manufacturing cost, and an average cost of 0.25 yen/m{sup 3} was obtained. (author)

  14. Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

  15. Development of materials of `bekko work` using horn; Gyukaku riyo ni yoru bekko daitai zairyo no kaihatsu

    Mori, S.; Nagata, S. [Technology Center of Nagasaki, Nagasaki (Japan); Sakoguchi, A. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-11-10

    The technical art `Bekko` is one of the traditional technologies in Japan, and the materials of `Bekko` are shells of hawksbills. However, the industry of `Bekko Work` has been facing a crisis recently, because the import of turtleshell is restricted. We have therefore tried to develop new materials as substitutes for the turtleshell by utilization of horn. The noteworthy aspects in this study are as follows: (a) It has been clearly established that the horn could be reformed with amber color similar to that of turtleshell by chemical treatment using hydrogen peroxide (H2O2). (b) It is also of interest that we produced new materials like `Bekko` by mixing horn powder and turtleshell powder at the appropriate ratio and molding them in the temperature range of 110-120{degree}C. 1 ref., 6 figs., 3 tabs.

  16. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

    NONE

    2000-03-01

    With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

  17. Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

    NONE

    1998-03-01

    This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

  18. Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

  19. Fiscal 2000 achievement report. Welfare technosystem research and development (Mizusawa); 2000 nendo walfare technosystem kenkyu kaihatsu (Mizusawa) seika hokokusho

    NONE

    2001-03-01

    For assisting aged people, healthy and living alone, in living without help, activities were conducted for (1) an electrical transmission experiment connecting residences (two, inhabited for the experiment) and a remote location (Techno-House) and (2) the development of a home server equipped with an electrocardiograph. Under item (1), data collected by sensors (occupancy sensor, open/close sensor, flame sensor, waterflow sensor) installed at the residences occupied by aged persons living alone were forwarded to Techno-House via CATV (cable television) and analyzed for the study of elderly people's behavior and daily life pattern. It was found that using this system the behavior of elderly people living alone might be detected even in the absence of their intention to report or communicate. Under item (2), an Ni-based electrode sheet was fabricated and installed in a bed and, via the sheet and a CATV channel, cardiographic waveforms were transmitted to Techno-House where the data were put into an analyzer for the examination of the elderly person's physical conditions. (NEDO)

  20. NEDO Forum 2000. Geothermal technology development session (new development of geothermal energy); Chinetsu gijutsu kaihatsu session. Chinetsu energy no shintenkai

    NONE

    2000-09-01

    The following themes were presented at this session: (1) geothermal development in the future, (2) the current status of geothermal development and utilization, (3) surveys on the promotion of geothermal development, and (4) verification and investigation on geothermal exploration technologies, development of hot water utilizing power generation plants, and international cooperation on geothermal development and utilization. In Item 2, report was made on the current status of geothermal power plants in Japan and their future development targets, long-term overview of geothermal development, measures and budgets to achieve the targets of geothermal development. In Item 3, it is reported that out of 48 areas completed of the survey (including the new promotion surveyed areas), the areas possible of steam power generation and confirmed of temperatures higher than 200 degrees C are 30 areas, and the areas possible of binary power generation (using down hole pumps) and small to medium scale power generation, confirmed of temperatures of 100 to 200 degrees C are 13 areas. In Item 4, reports were made on the reservoir bed variation exploring method, surveys on deep geothermal resources, a 10-MW demonstration plant, a system to detect well bottom information during excavation of geothermal wells, a technology to collect deep geothermal resources, and a hot-rock using power generation system. In Item 5, geothermal exploration in remote islands in the eastern part of Indonesia, and the IEA cooperation projects were reported. (NEDO)

  1. Fiscal 1995 geothermal development promotion survey. Natural environment survey report; 1995 nendo chinetsu kaihatsu sokushin chosa. Shizen kankyo chosa hokokusho

    NONE

    1996-03-01

    In Candidate C area for the geothermal development survey, the natural environment was surveyed and `the secondary landscape assessment` was summed up in which places proposed for drilling of large-size wells and for construction of power generation facilities are extracted and a simulation of the landscape is conducted. The area for survey is the Shiramizu-gawa region in the south of Lake Akan, Akan-cho, Akan-gun, Hokkaido. The field survey was carried out about three items of landscape, plants and animals during the June-November period, 1995. As to the flora, diverse florae including vegetation unique to alpine areas, wetlands, and fumarole surrounding areas were found in the region, which is covered with summer-green broad-leaved forests or mixed forests of coniferous and broad-leaved trees. As to the fauna, faunae inhabitant of the highly natural forests were found including black woodpeckers and mountain hawk eagles. As a result of studying the places proposed for geothermal development from the above-mentioned survey, two places were picked up in the west of the survey area, where geothermal development is comparatively less influential in the natural environment and landscape and there is a high locational adaptability. 19 refs., 56 figs., 49 tabs.

  2. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  3. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  4. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

  5. Outline of geothermal energy research and development in fiscal 1999; Heisei 11 nendo chinetsu enerugi kenkyu kaihatsu no gaiyo

    Konishi, T. [Agency of Industrial Science and Tehcnology, Tokyo (Japan)

    1999-11-18

    In this paper, the outline of the budget of geothermal energy relation in fiscal 1999, the system of research and development and the outline of research and development are described. Budgets in fiscal 1999 are the general account 17 million yen, the power development special account 3,222 million yen, sum total 323,900 million yen and it is a 33 million yen decrease compared with the preceding year. Within research and development, the following are included as a survey investigation research; a geothermal energy survey and picking technology, a verification investigation of a geothermal energy exploration technique, a deep geothermal resource investigation and an analysis and evaluation therefor. As a development of geothermal energy power plants using hot water, the following are included; development of the 10 MW binary cycle power generation plant, development of the bottom hole information system (MWD) in geothermal well drilling, technology development of the geothermal hot dry rock source system. As an analysis and evaluation of the bottom hole information detection system in geothermal well drilling, the following are included; an analysis and evaluation of the hot dry rock thermal extraction system, an analysis and evaluation of the deep geothermal resources picking technology, an analysis and evaluation of metallic materials for the geothermal deep direction and an analysis and evaluation of high polymer materials for the geothermal deep direction. (NEDO)

  6. Geothermal development promotion survey. No. B-3 Kumaishi area; Chinethu kaihatsu sokushin chosa seika hokokusho. No. B-3. Kumaishi chiiki

    NONE

    1999-03-01

    This paper summarizes the result of a geothermal resource survey carried out from fiscal 1995 through fiscal 1997 in the Kumaishi Area located in the western center of Oshima Peninsula in the south western part of Hokkaido. The survey for this area was performed with an objective to search the spread of high temperature area continuing from the adjoining Yakumo area where the highest temperature of 233 degrees C has been confirmed in a structural test well (N63-YK-6), to identify high water permeating areas in great depth points underground, and to find possibility of existence of geothermal resources. The survey included geological and alteration zone survey, geochemical survey, gravitation exploration, electromagnetic exploration, drilling and temperature logging of five structural test wells, water injection test, temperature restoration test, core survey and hot water survey. Also performed were environmental effect survey, rock age measurement, alteration age measurement, and fluid inclusion test. As a result of the survey, it was identified that the verified geothermal hot water has been stored in granites with poor water permeability, whose low temperature has not formed convection systems spreading in wide areas despite having been heated, making each system exist in small scale independently. It was estimated that the possibility is low to expect geothermal power generation. (NEDO)

  7. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

  8. Development trend of low bypass ratio turbofan engines. Tei baipasu hi tabo fan engine no kaihatsu doko

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1994-03-10

    As a turbojet engine gets a thrust by blowing out the exhaust of a gas generator, for decreasing the fuel consumption ratio is more advantageous when a bypass air quantity is made as much as possible. Therefore in the subsonic speed passenger aircrafts putting an economy in the first place, the high bypass ratio turbofan engines are used. Even in case of the subsonic speed aircrafts, in addition, for the trainer airplanes and fighters, a type to be built in the engines in the fuselages, the low bypass ratio engines with small front areas are used. When a turbofan engine with a low bypass ratio is picked up, therefore recently, it is general that a military engine with a bypass ratio under 1 (about 0.5 is frequent) is pointed, as for a development trend also from a viewpoint of the performance improvement as a military engine, an improvement of the thrust-weight ratio and specific thrust are attached importance to. In this paper, these performance parameters, a trend to make them lighter weight, and the elementary technologies peculiar to a low bypass ratio engine are described, and moreover the study and development state in Europe, America and Japan are put in order. 8 refs., 14 figs., 2 tabs.

  9. Development trend of high bypass ratio turbofan engines. Ko baipasu hi tabo fan engine no kaihatsu doko

    Tonomura, Y [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

    1994-03-10

    The turbofan engines for private aircrafts have come to have a high bypass ratio because a performance improvement is always requested. Because a turbofan engine is always required for a thrust reinforcement to correspond the stretch and weight increase of a fuselage after acquiring a type approval, making them a series to cover a certain thrust range becomes necessary. The concrete methods to reinforce a thrust are being achieved by an increase of fan diameter, a partial modification of high pressure compressor, a temperature rise of high pressure turbine inlet, a stage number increase of low pressure turbine, and a combination of these items just mentioned above. The PW 4000 series, CF6 series and RB211 series currently under production are being reinforced in a thrust by these methods. In this paper, as the representatives of some turbofan engines incorporating the most advanced technologies, as for 3 kinds of the large scale turbofan engine presently under development for the B777, namely GE90, PW4084, and TRENT800, their distinctive futures are summarized. 25 figs., 1 tab.

  10. Research and development of cooled turbine for aircraft engines. Koku engine yo reikyaku turbine no kenkyu kaihatsu

    Maya, T; Yamawaki, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    For the turbine which is one of the principal elements of aircraft engine, progress in turbine use material development and cooling performance further heightened for the turbine are needed to grapple with the required heightening of turbine inlet temperature. In the present paper based on the turbine inlet temperature designed to be 1600[degree]C as a target, a two-dimensional model used for the turbine cooling performance test was structurally given together with the result of the above test which aimed at confirming the design calculation. As a result of cooling design for the turbine which was about 1600[degree]C in inlet temperature, the highest gas temperature was 1890 and 1470[degree]C on the stator blade and rotor blade, respectively. Both those blades were 0.66 and 0.62, respectively in cooling efficiency. To test the cooling performance, a two-dimensional cascade was tested with a doubly amplified model of cooling blade, the use of which could set its Reynolds number near that of the actual one. As compared with the actual operation, the test was made at low temperatures of 400 to 500[degree]C and low pressures of 0.02 to 0.03MPa. The test agreed with the design calculation in result. 4 refs., 8 figs.

  11. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  12. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

    NONE

    1998-03-01

    With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

  13. Fiscal 1997 achievement report. Research and development of synergy ceramics; 1997 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    NONE

    1998-03-01

    Research and development is conducted on two subjects, that is, 1) hyper organized structure control technology and 2) structural element control technology. In addition, joint research and development is conducted on the creation of new materials by hyper organized structure controlling, hyper organized structure controlling for ceramics by a structurization reaction process, designing of precursors to ceramics, and the hyper organized structure control for ceramics by nanostructure process control. The joint research and development endeavors further deal with re-entrusted projects which involve researches on sintered structure control by powdery particulate structure control; dynamic process of synergy ceramics; oxynitride liquids, glasses, and glass-ceramics; and multifunctional ceramic laminates for engineering applications. Under subject 1), researches are made on the development of precursors into ceramics by utilizing chemical reactions of organic metal compounds, and analyses are conducted into the effects, exerted by the molecular structures of precursors and the conditions of a reaction for their development into ceramics, on the microstructures and various properties of the ceramics to be composed. Under subject 2), high strength, great hardness, and high resistance to wear are realized by allowing the precipitation of nano-particulates in crystals of a fine and very compact sintered body of alumina. (NEDO)

  14. Interim evaluation report on research and development of automatic sewing systems; Jido hosei system no kenkyu kaihatsu chukan hyoka hokokusho

    NONE

    1988-03-01

    The research and development project for automatic sewing systems is aimed at establishing the techniques necessary for developing (automatic sewing systems) which efficiently produce diversified types of products in small quantities, to cope with various requirements, e.g., diversified consumers' needs and reduced cycle periods. This project covers R and D of the sewing preparation/processing, sewing/assembling, cloth handling, and system management/control techniques. The program for developing the total systems and elementary techniques draws the conceptual designs of their functions, performance and shapes, to outline the overall R and D project. The programs for the individual elementary techniques include studies on their basic functions and performance; design works from the basic designs to determine the specifications to the detailed designs of the devices to be developed; construction of the test units on a trial basis; and function confirming tests to confirm operability of the unit components and device performance, where these works are simultaneously implemented. This paper describes the interim results of evaluation of the elements developed for the elementary techniques, summarizing the results obtained so far. It is concluded that most of the targets of the R and D themes are sufficiently achieved by the end of FY 1987, and that the project can be now advanced to the next phase, construction of the test plants. (NEDO)

  15. Survey research report by the hydrogen occluding alloy utilization development committee; Suiso kyuzo gokin riyo kaihatsu iinkai chosa kenkyu hokokusho

    NONE

    1985-03-01

    This report summarizes the FY 1984 survey research results, issued by the hydrogen occluding alloy utilization development committee. The basic property subcommittee is responsible for collecting published data related to the basic properties of metal halides as much as possible, and pigeonholing them to have the data which can contribute to development of the new alloys for basic researches and engineering applications of hydrogen occluding alloys. The subcommittee members have collected these data. The common theme subcommittee has planned to collect the P-C-T diagrams of the hydrogen occluding alloys and new alloys as much as possible, for the designs, development, production and system designs of the hydrogen occluding alloys. The P-C-T diagrams have been collected for a total of 340 types of alloys, which fall into the broad categories of Mg-based, TiFe-based, TiMn-based, other Ti-based, rare-earth-based, Zr-based, Ca-based and others. The analytical methods have been also investigated while collecting P-C-T diagrams. (NEDO)

  16. Development of combined brake system on front and rear brakes for scooter; Scooter yo zenkorin rendo brake system no kaihatsu

    Okazaki, Y; Itabashi, T; Shinohara, S; Honda, Y [Honda R and D Co. Ltd., Tokyo (Japan)

    1997-10-01

    Scooters need appropriate front and rear wheel braking power distribution and each of front and rear brakes have been operated using right and left levers. This time, a low cost brakes with cable type combined brake system for small size scooter and a brakes with hydraulic type combined brake system for middle size scooter have been developed to obtain appropriate front and rear wheel braking power distribution. Both systems use convenient left lever to operate. 3 refs., 9 figs., 1 tab.

  17. Development of measuring system for automobile unit assembly equipment; Jidosha buhin seisan setsubi no keisoku system kaihatsu

    Miura, M; Uchishiba, I; Fukunishi, T; Umemura, H [Toyota Motor Corp., Tokyo (Japan)

    1997-10-01

    This measuring system has two characteristics. The first characteristic is to shorten lead time from system design to production. The second characteristic is to accomplish system construction simply without computer technical knowledge. This measuring system consists of hardware module which are standardized according to functions and software packages which are composed of various functions. This system is put together according to purpose. When it was introduced into production line, it could shorten lead time of 1/3. 10 figs., 1 tab.

  18. FY1995 development of the landscape design studio; 1995 nendo jiritsu bunsan kyochogata 'keikan studio' no kaihatsu

    NONE

    1997-04-01

    Establish a distributed design studio called 'The Landscape Studio' for designing and analyzing landscape collaboratively under Internet and multimedia computer environment. We first proposed a concept called 'Open Designing' for design works under information environment, which is composed of three kind of openness: open data, open processes, and open discussion. Based on the concept a landscape studio has been established as a total design system towards the forthcoming network and multimedia age. In the studio, a large volume of maps, images and other data are stored in the form accessible through the Internet. Using the data of several study areas, including Omotesandou street, Block 10 of Azabu, computer simulations, design games, VRML, CAVE and many other designing support tools have been developed the studio. Furthermore, the research team joined the activities of the Angkor Wat Safeguarding Project supported by UNESCO and the Japanese government. The locations and shapes of ruins in a wide area were (measured and simulated in a 3 dimensional style. The researches of Landscape Studio were reported at several exhibitions such as 'The 2nd Exhibition on Computer Aided Architectural Design' and 'The 11th Exhibition on Architecture, City and Computer'. The multimedia systems and experiments in the studio lead the field of multimedia urban and landscape design, and the research activities have greatly contributed to the education and industry of urban design. (NEDO)

  19. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

    NONE

    1998-03-01

    A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

  20. Achievement report on developing superconductor power applied technologies in fiscal 1999 (2). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

    NONE

    2000-03-01

    With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power generators. This paper summarizes the achievements thereof in fiscal 1999. A verification test was given on the rotor of an ultra high speed responding generator. In a sudden short circuit test using the different phase charging method, no anomalies were found such as quench generation and vibration changes, wherein the healthiness of the generator was verified. In the VVVF actuation test, knowledge was acquired on the actuation method when the ultra high speed responding generator is applied to a combined cycle plant. After the verification test has been completed, the disassembly inspections such as visual check and non-destructive test were performed. With regard to the vacuum leakage found in the rotor under very low temperatures, the causes were presumed and the countermeasures were discussed by observing the weld structures. In the design research, the conception design on the 200-MW pilot generator was reviewed by reflecting the results of the verification tests on the model generator. At the same time, trial design was made on a 600-MW target generator. In summarizing the overall research achievements, the achievements and evaluations were summarized on technological issues that have been allotted to each research member. (NEDO)

  1. Development of WISH type transportable toilet with water circulation; WISH hoshiki kahangata junkan suiryushiki toire no kaihatsu

    Amagai, B; Imaizumi, S [Leader Co. Ltd., Gunma (Japan); Ushiyama, I [Ashikaga Institute of Technology, Tochigi (Japan); Onai, Y

    1997-11-25

    Described herein are a proposed ``WISH (wind and solar hybrid) type portable toilet with water circulation,`` in which wind and solar power generation units are combined, and specifications of the toilet unit for 2 persons. It needs 2.2m{sup 3} of initial charge of water, which can be circulated by power stored in the battery unit in 2,600 to 3,000 cycles. Water can be kept at a pH level of 8 or lower, when circulated 200 times or less for a day. This number is increased to 500, when 2 units are installed. Dirty water is treated by an agent and circulated without being exhausted and without releasing offensive odor. Circulating water is recycled while being totally sterilized, whereas sludges are exhausted after being solidified by a powerful coagulant. The toilet unit is equipped with a pump (50W) and fan (75W). The solar unit generates power of at least 1.08Wh/day and the wind unit is equipped with a small-size generator having a rated capacity of 300W. The toilet units are commercialized and showing good results. 2 refs., 5 figs.

  2. Design and performance of multiple effect basin type solar still; Basin-taju koyo fukugogata taiyonetsu joryuki no kaihatsu

    Tanaka, H; Nosoko, T; Nagata, T [Univ. of the Ryukyus, Okinawa (Japan)

    1997-11-25

    A seawater desalinating still was devised, which utilizes solar heat and combines a basin type still with a multiple effect type still. The devised still has a triangular cross section, has a seawater basin at its bottom, wherein the slope facing the sun has a double glass window, and the other slope is arranged with a multiple effect still (three-step effect system). The sun light that has permeated the double glass window heats and evaporates seawater on the basin. Majority of the generated steam is condensed at the lower face of a lowermost partition of the multiple effect section, and its latent heat evaporates the seawater contained in a wick on the rear side. The steam is condensed at the lower face of the second partition, this action is repeated sequentially to upper plates, and the heat is discharged finally into the surrounding air from the uppermost face of the multiple effect section. Seawater is supplied from the upper part onto the wick in each partition, which is evaporated, condensed and recovered at the lower part. The condensate is recovered at the lower part of each plate. The construction is simpler than the conventional downward indirect heating multiple effect type still, and the distilling efficiency is improved by 30%. Technological difficulty in the upward direct heating multiple effect type still can also be improved. 6 refs., 6 figs., 2 tabs.

  3. Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

  4. Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    NONE

    1998-03-01

    This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

  5. Fiscal 2000 achievement report. Welfare technosystem research and development (Chofu); 2000 nendo welfare technosystem kenkyu kaihatsu (Chofu) seika hokokusho

    NONE

    2001-03-01

    Research and development efforts are exerted to realize (1) a variable function residential circumstance system for the aged people and (2) a medical welfare and life assisting information system for helping the aged or handicapped people lead an independent life. Under item (1), a variable function residential circumstance system under which functions of the residence may be changed dependent upon inhabitants' degree of debility will be developed, and an information system will be developed under which medical welfare assistance and life assistance are integrated. Under item (2), residences, welfare appliances, and nurse/attendant assisting systems will be assessed and examined. In fiscal 2000, under item (1), a variable function residential unit was fabricated and was inhabited experimentally by people approximately 1 to 4 in the degree of need for nursing care, and problems were isolated to be discussed toward putting the system to practical use. Under item (2), physical power required for nursing and attending was measured using medical assistance appliances for in-home nursing care installed at Welfare Technohouse Chofu, and ergonomic studies were conducted with a view to relieving the load to be imposed upon those engaged in the nursing and attending work. (NEDO)

  6. Research of fluidized bed cement clinker sintering system by pilot plant; Ryudosho cement shosei gijutsu no kaihatsu. 7

    Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Sato, N; Hashimoto, I; Nakatsuka, M [The Cement Association of Japan, Tokyo (Japan)

    1996-09-01

    While a cement manufacturing process generally performs sintering by using a rotary kiln, a development work has been carried out as a subsidy operation of the Agency of Natural Resources and Energy on a cement sintering technology using a fluidized bed consisted of two furnaces: a jet flow bed granulating furnace and a fluidized bed sintering furnace. This paper reports the results of tests and researches performed during fiscal 1995. A plant with a scale of 20 ton-a-day production started in 1993 after having gone through bench scale tests. The year 1995 conducted by August its performance evaluation, review of the operation method and the safety criteria, and generalization of the tests. A multi-stage cyclone system has been employed in the preheating equipment for cement material powder. A number of improvements have been realized in the aspects of construction and operation, such as stabilization of dust collecting efficiency by employing a high-efficiency type cyclone, and operation with reduced pressure variation. Based on these results, a construction had been progressed in parallel on a new plant upscaled to 200 ton-a-day production. The new plant was completed in December, 1995. 9 figs., 8 tabs.

  7. Separation of unburned carbon from coal fly ash through froth flotation; Sekitanbai no shisshiki datsutanso gijutsu kaihatsu shiken

    Miwa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Murakami, T [The Coal Mining Research Center, Japan, Tokyo (Japan)

    1996-09-01

    Coal ash tends to become containing more unburned carbon and porous substances depending on conditions of combustion, whose adverse effects to products due to water adsorbability, absorbability and color tones create obstacles in its utilization. Therefore, research and development works have been progressed on wet type carbon removing technology which is characterized in that coal is pulverized to preferable degrees and subjected to flotation. This paper reports the results obtained during fiscal 1995. The results may be summarized as follows: as a result of the comparison test on a column flotation machine and an FW type flotation machine of machine stirring type, the former machine showed better flotation efficiency; several methods were investigated on crushing as a treatment prior to flotation, whereas a mixer with greater circumferential speed and a homo mixer showed the highest efficiency; strength of the impact to the flotation efficiency was found to decrease in the order of pulp concentration > pretreatment time > collector addition ratio; and as a result of the evaluation on refined ash as a cement admixture and carbons as fuel, possibilities were found in them for practical application. 16 figs., 2 tabs.

  8. Development of production technology for deep-seated geothermal resources; Shinbu chinetsu shigen seisan gijutsu no kaihatsu gaiyo

    Wada, T.; Akazawa, T. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1997-11-01

    In order to increase the geothermal power generation volume in Japan furthermore after now, it is necessary to develop the deep-seated geothermal fluid collecting technique at 3,000 to 4,000m in depth and about 350degC. In order to collect the deep-seated geothermal resources economically and effectively, there are some principally important problems on production techniques such as P (pressure)-T(temperature)-S (flow rate)-D (fluid density) logging technique, P (pressure)-T (temperature)-C (chemical composition) monitoring technique, high temperature tracer monitoring technique, scale monitoring technique, scale protection and removal technique and so on. The PTSD logging technique is a measuring technique for collecting some data necessary to conduct production management effectively. The PTC monitoring technique is a technique for collecting data on the geothermal resources essential for the resources evaluation and presumption, and tracer monitoring technique is a technique for collecting actual measurement data of fluid flow analysis in the deep-seated geothermal resources. And the sale monitoring is a technique for collecting data on various kinds of scale components of the deep-seated geothermal water and in the steam. In this paper, these techniques are summarized. 8 figs.

  9. Fiscal 1993 survey report. Coal hydrogasification technology development; 1993 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    NONE

    1994-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. The hydrogasification process that Japan should develop is a flexible process that operates on the three modes of the maximum SNG yield, the maximum heat efficiency, and the maximum BTX (benzene, toluene, xylene) yield. Such being the case, an ARCH (advanced rapid coal hydrogasification) process was proposed, provided with a reactor capable of an ARCH-1 type operation for the maximum gas cooling efficiency and an ARCH-2 type operation for the maximum liquid yield. As for the details of the ARCH process development, the time and priority for development were determined for each of the items in consideration of the technical contents and the steps of development in the flow from a bench plant to a demonstration plant. The technology of char cooling and extraction was specified as the first item to be immediately dealt with. As for the development of the hydrogasification reactor, it was concluded that it was suitable to begin with the development of an injector. According to the development plan, the cost required up to a pilot plant test was estimated at 2 billion yen. (NEDO)

  10. Development of an in-situ banking shear test method; Moritsuchi no gen'ichi sendan shikenho no kaihatsu

    Nishikata, U. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-12-10

    Development was made on a simplified site-use single face shear testing device and a test method that can perform in-situ and direct measurement during construction on shear strength of coarse particle materials having large diameters. The test device consists of shear frames embedded in the in-situ ground bed, a weight for vertical loading, and a traction device to load horizontal force. In the test, prescribed rolling compaction is performed by a vibration roller which presses in the shear frames into unwound banking by using a four-piece vibration roller. Crushed stones are piled on cells of the shear frames to the same height. The specified weight is placed thereon via a loading plate, which is used as the vertical load. The shear force is loaded by horizontally pulling chains connected to the shear frames by using the traction device, and is measured by a load cell. The vertical displacement is measured by two vertical displacement meters, and the horizontal displacement by one horizontal displacement meter. A verification test is continuing using the test device. Four cases with different vertical stresses can be tested in about one day. (NEDO)

  11. Report on the achievements in the projects subsidized by the Sunshine Project in fiscal 1981. Data 3. Development of a coal liquefaction technology - development of a solvent extraction and liquefaction technology - 'development of a brown coal based solvent extraction plant' (Development of a 50-t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 3). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    Developmental researches were carried out on a liquefaction plant for the Victoria brown coal produced in Australia (a 50-t/d pilot plant). In fiscal 1981, detailed design was performed on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the devices was procured, and the site construction was begun. The present data is a collection of drawings in relation with the instrumentation design, such as the meter specifications, front view drawings for meter panels, drawings for panel arrangement in the central control room, a computer room layout drawing, control system explanation drawings, interlock diagrams, and the instrumentation power supply diagrams. (NEDO)

  12. Fiscal 1992 survey report. Coal hydrogasification technology development; 1992 nendo sekitan suiten gaska gijutsu kaihatsu chosa hokokusho

    NONE

    1993-03-01

    Surveys and studies were conducted to establish a practical SNG (substitute natural gas) production process. In the study of coal hydrogasification, a mathematical simulation was implemented to estimate the distribution of products with the pyrolytic reaction and the hydrogenolytic reaction controlled independently in the ARCH-2 (advanced rapid coal hydrogasification-2) process, the said two reactions representing the key concepts of the ARCH-2 process. It was then disclosed that a two-stage reaction control would increase the liquid yield. Also, a tentative calculation was made of gas cooling efficiency and cost performance in a process capable of achieving the target liquid acquisition rate. It was then found that BTX (benzene, toluene, xylene) production up to approximately 15% in terms of carbon was feasible and that the SNG price would be 29.03 yen/Nm{sup 3} with benzene priced at 90 yen/kg, these promising a better result than in the ARCH-1 process. The gas cooling efficiency of the ARCH-2 process was but 72.0% or less, however, which demanded improvement. Studies were made, based on the results of studies in progress since fiscal 1990, about what the hydrogasification process for Japan to develop should be. (NEDO)

  13. Fiscal 1998 achievement report on welfare technosystem research and development. Kyoto; 1998 nendo walfare technosystem kenkyu kaihatsu (Kyoto) seika hokokusho

    NONE

    1999-03-01

    To be ready for the computing-everywhere age to come, it is necessary to create environments in which the barrier-free utilization is ensured of various apparatuses of the daily routine, such as various bodily function substituting apparatuses capable of compensating for the degraded functions of disabled or aged individuals. Under the circumstances, a system for building man-machine interfaces in the home or the like is required, and fundamental technologies of architecture and information infrastructure have to be established on which the development of technologies for the field involved will proceed. Concerning the technologies already in existence in this field of research, a survey is conducted of the status of research and development of information interface techniques primarily at Stanford University, and a report is made thereon. Also reported is the information obtained at Technology and Persons with Disabilities Conference 1999. The result of a survey of the trend of research and development of the smart house under the TIDE (Technology Initiative for Disabled and Elderly People) project and the result of a survey of an information standardization project for equipment control in Europe are reported, and the result of a survey of the approach of Kyoto's welfare apparatus distributors to the development of equipment is made known. (NEDO)

  14. Development of a Fe-Ni battery for electric vehicle use. Denki jidoshayo tetsu nickel denchi no kaihatsu

    Onozuka, T.; Okuda, K. (The Tohoku Electric Power Co. Inc., Sendai (Japan))

    1993-08-11

    Development has been made on an iron-nickel battery as a low polluting electric vehicle battery that is superior in low-temperature performance to lead-acid batteries. This paper summarizes the battery. The battery uses NiOOH for positive electrodes, Fe for negative electrodes, and alkaline aqueous solution for electrolyte. The battery was manufactured in the following manners to make it suit the electric vehicle application: The iron electrode was manufactured by mixing reduced iron powder having grain sizes from 5[mu] to 6[mu] with electrolyzed iron powder with grain sizes from 20[mu] to 30[mu] in a bonding agent, and sintered at temperatures from 750[degree]C to 800[degree]C in H2 atmosphere; iron electrodes that have superior life and material utilization factor were found to have reduced iron powder ratios from 20% to 30%; the nickel electrode consists of a substrate obtained by coating metallic Ni powder on a sheet and sintering it and filling it with NiOH; the electrolyte is composed of KOH containing LiOH and KS; the separator uses a ribbed PVC porous sheet; the container is made of PP; performance evaluation tests were conducted on discharge performance, energy density, output density, temperature characteristics, charge efficiency, and cycle life; and the results of vehicle driving tests surpassed those from lead-acid batteries. 6 refs., 18 figs., 6 tabs.

  15. Development of a thin-shaped lightweight MF battery for motorcycles. Nirinshayo usugata keiryo maintenance free battery no kaihatsu

    Takahashi, S.; Onozuka, T. (Honda Motor Co. Ltd., Tokyo (Japan)); Uemichi, S. (Yuasa Battery Co. Ltd., Osaka (Japan))

    1992-08-01

    This paper describes a thin-shaped lightweight maintenance free motorcycle battery used in a motor scooter, a new product from Honda Motors launching its sales in 1992, as well as the related structural development thereof. The points aimed at in the development include more utilization of available space in a vehicle, improved maintainability, and adoption of perfect instant activation system (dry-charged system) which makes a battery serviceable upon initial filling of electrolyte. Attentions have been given on reducing the battery volume by 30% and weight by 20% compared with the conventional batteries, and ensuring interchangeability, leakage-free performance, and free and easy replacement. Contrivances for practical application have been given on assuring low-temperature high-rate discharge performance for reliable engine starting. Devised also are the thinner battery plates, better vibration resistance, longer life, uniformed plate thickness, higher separator porosity, and better stability in plate group pressurization. Better performance than the conventional batteries was realized by improving parts construction and mounting systems, including one-touch terminal connection, fast coupling of terminal posts, soldering, and fuse built-in couplers. The battery has superior appearance and design. 18 figs.

  16. Flow velocity anemometer using ultrasonic waves in underground airways. Choonpa wo mochiita chika fudo fusokukei no kaihatsu

    Sasaki, K.; Imai, T.; Miyakoshi, H. (Akita Univ., Akita (Japan). Mining College); Onozuka, T.; Yasunaga, K. (Hanaoka Mining Co. Ltd., Akita (Japan))

    1993-10-25

    In a facility utilizing the subterranean space at the great depth of about 50m or less from the surface in particular, the airflow velocity monitor utilizing ultrasonic waves is considered as an airflow anemometer suitable for the environment of an underground airway network. In this paper, the results of the application test and the long term demonstration test both conducted at Matsumine Mine and Fukazawa Mine of Hanaoka Mining Industry are mentioned which concern the newly developed airflow velocity monitor utilizing ultrasonic waves. The features and performance of this ultrasonic wave monitor are roughly as follows; since a small ultrasonic wave transceiver can be installed on the surface of the airway wall, the transceiver does not become an obstacle for traffic in the airway and the average airflow velocity in the airflow path can be estimated with accuracy better than that of the anemometer for point measurement. The airflow direction at the underground airway can be detected. The responsiveness to airflow velocity fluctuations is relatively good. The abrupt ups and downs of output due to passing transportation machines can be detected. The measuring circuit has been simplified by the analogue treatment of time measurement. The average airflow velocity at the airflow velocity profile can be estimated through multiplication by 0.93 of the airflow velocity value measured with the monitor. 11 refs., 16 figs., 1 tab.

  17. Execution management of batter piles and problems of technical development. Uchikomi kui no seko kanri to gijutsu kaihatsu no kadai

    Ninomiya, Y [JDC Corp., Tokyo (Japan); Omori, H [Nippon Kokan Koji K.K., Yokohama (Japan)

    1991-05-15

    This report introduces the practical examples of the present system of execution manegement. Necessary functions and basic problems are described as well as the possibility of utilizing hydraulic/pneumatic pressure for the automation or the robotization which are the future technical problems. Application examples are also shown on the execution management system by means of an accelometer which was developed by the authors. This area is not long after the start of study. Essential points of the execution management of the batter piles are that the front tips of the piles are confirmed to be securely penetrated to the specified depth in the specific support layer giving the required supporting strength at the same time. For this purpose, what are required are to accurately measure the penetration displacement of the piles and assess the maximum penetration and final penetration and the amount of the rebound. Then the support strength should be checked from the dynamic support force. For this, it is required to develop an execution management system which is simple and adept for the operation at the spot. 9 refs., 12 figs., 5 tabs.

  18. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

    NONE

    2000-03-01

    The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

  19. Survey of an evaluation method for research and development projects; Kenkyu kaihatsu project no hyoka shuho ni kansuru chosa

    NONE

    1997-03-01

    This report describes an interim evaluation method and a concrete evaluation method for projects promoted by the Agency of Industrial Science and Technology, and NEDO. As a result of the survey, a method of highly practical interim evaluation, concrete evaluation items, and evaluation criteria have been proposed by assuming that the projects are evaluated by the project evaluation department independent of the project promotion department. Long-term issues for constructing the evaluation system are also described. It is the most essential for the evaluation to fulfill the function of effective promotion of the following projects. It is also indispensable for the evaluation method and issues proposed in this report to communicate closely to project promoters and researchers, and to reassess the projects continuously. Continuous consideration for the feedback of evaluation process and the improvement of evaluation are significant for the long-term construction of system. 21 refs., 9 figs., 23 tabs.

  20. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    NONE

    2000-03-01

    The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

  1. NEDO coal resources exploitation subcommittee. 18th project report meeting; NEDO sekitan shigen kaihatsu bunkakai. Dai 18 kai jigyo hokokukai

    NONE

    1998-09-01

    In a report on a 'survey for coal transportation system optimization in southern Sumatra' which is to contribute to the improvement of coal exploitation efficiency in the Musi river area in southern Sumatra, the coal transportation system from the coal mine to the harbor is reviewed, scenarios on funding and cost effectiveness and environmental impact are comprehensively examined, and suggestions are submitted for higher efficiency and cost effectiveness. In a report on a 'current utilization status and effectiveness of a non-destructive electromagnetic vibrator shock source,' an electromagnetic vibrator shock source out of several new coal exploration technologies which are combinations of test boring and seismic prospecting is taken up, and is compared, in terms of technical feature and cost effectiveness, with the seismic reflection survey technique that uses an explosive shock source, and then a conclusion is reported that an electromagnetic vibration shock source method is superior. Using the new electromagnetic method, a seismic wave frequency is so chosen as to be suitable for a given depth. Since it is non-destructive and emits less noise, it is expected that it will serve in various fields other than coal mining. (NEDO)

  2. Noise and vibration reduction technology in hybrid vehicle development; Hybrid sha kaihatsu ni okeru shindo soon teigen gijutsu

    Yoshioa, T.; Sugita, H. [Toyota Motor Corp., Aichi (Japan)

    2000-03-01

    Accomplishing both environmental protection and good NVH performance has become a significant task in automotive development The first-in-the-world hybrid passenger car of mass production. 'Prius', has achieved superior NV performance compared with conventional vehicles with a 1.5-liter engine along with 50% reduction of fuel consumption and CO{sub 2} emissions. low HC, CO and NO{sub x} emissions. This paper describes NV reduction technology for solving problems peculiar to the hybrid vehicle such as engine start/stop vibration, drone noise at low engine speed and motor/generator noise and vibration. It also mentions application technology of low rolling resistance tires with light weight wheels and recycled material for sound proofing. (author)

  3. Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

    NONE

    1999-03-01

    For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

  4. Development of an antimicrobial concrete to inhibiting corrosion; Konkurito wo fushoku kara gado suru kokin konkurito no kaihatsu

    Kurihara, Y.

    1999-11-10

    It has been clarified that the corrosion of concrete in sewage facilities is caused by the action of specific microorganism. The corrosion of concrete is caused by the complicate interaction of chemical substances and microorganisms existing in sewage water. As microorganisms related to this phenomenon, lead sulfate reductase and sulfur oxidase are well known. This paper introduces antimicrobials for concrete using zeolite as a main component and a concrete containing these antimicrobials, which were developed for killing or suppressing the generation of these microorganisms causing the corrosion of concrete. The sales results during 2 years since the start of the sales in May 1997 was 16 tons for antimicrobials including zeolite-supported silver - copper catalyst, and 8,138 tons for antimicrobial concrete. Sixty-eight companies have organized , which will promote the popularization and technical guidance of antimicrobial concrete. (NEDO)

  5. Fiscal 1999 achievement report. Research and development of synergy ceramics; 1999 nendo synergy ceramics no kenkyu kaihatsu seika hokokusho

    NONE

    2000-03-01

    Studies are conducted on three subjects, which are the development of 1) high-temperature energy materials technology, 2) ultrasophisticated materials technology, and 3) high-performance active materials technology. Under subject 1), high-strength porous materials are to be developed, which are resistant to heat and corrosion, tolerant of damage and deformation, and light in weight. In addition, relative to fluid transmission, materials are to be developed, which are highly resistant to heat, corrosion, and thermal impact, and capable of separating and removing particulates of powder dust. Under subject 2), efforts are under way to develop two technologies, related to materials creation and their application. The former technology involves the development of a process of simultaneously equipping materials with high wear resistance, desired friction factors, and desired mechanical and thermal characteristics; a process of equipping them with a trace damage detecting function; and a process of simultaneously equipping them with functions of restoration from accidents and of self-lubrication. Relative to the latter technology, efforts are conducted, in coordination with the endeavors for the above-said materials creation technology, to develop materials and their application with attention paid to some specified functions. Under subject 3), self-complete type ceramic materials not requiring an external driving power source are to be developed, in which a selective cleaning function and environmental energy conversion function are amalgamated. (NEDO)

  6. Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

    NONE

    2000-03-01

    Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

  7. Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

    NONE

    1998-03-01

    The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

  8. Development and applicability estimation of the tire contact pressure measurement system; Tire secchiatsukei no kaihatsu to oyosei hyoka

    Mizutani, Y.; Amago, T.; Takahashi, T.; Sakuma, S.; Mori, N. [Toyota Central R and D Laboratories, Inc., Aichi (Japan); Nagae, A. [Toyota Motor Corp., Aichi (Japan); Yasuoka, M. [Toyo Tire and Rubber Co. Ltd., Osaka (Japan)

    1995-04-20

    A pressure sensor more reliable than the conventional types and a tire pressure measurement system using a plurality of sensors of the said reliable type have been developed. The sensor is an inverted T in shape, the upper surface of the vertical beam thereof receives the pressure, and the two ends of the horizontal beam are fixed. The load per unit area imposed on the pressure receiving surface is separated into three components, the X and Y components in the tangential direction are sensed by the vertical beam while the Z component in the vertical direction is sensed by a distortion gauge attached to the horizontal beam. For the measurement of the contact pressure distribution for the entire contact surface, a measuring device was developed, comprising a multiple point contact pressure gauge with 30 sensors of the reliable type discussed here embedded therein, a tire rolling tester, and a data processing unit. A tire wear estimation test was conducted using this pressure sensor and a contact probe type slip sensor, and it was found that a tire of a greater friction energy ratio is easier to experience abnormal abrasion and that the new pressure sensor is useful in estimating abnormal abrasion. Further, it was indicated that the present measuring device is applicable to the analysis of the mechanism wherein shaft force results from contact pressure on the soil. 3 refs., 11 figs., 3 tabs.

  9. Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

    NONE

    1996-03-01

    Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

  10. Development of high strength steel sheets for crashworthiness; Shototsu anzen`yo kokyodo usu koban no kaihatsu

    Fukui, K; Yamamoto, M; Mizui, N; Hirose, Y; Kojima, K [Sumitomo Metal Industries, Ltd. Osaka (Japan)

    1997-10-01

    For frontal or rear members of automotive body, the most suitable high strength steel was investigated. Dynamic tensile test at strain-rate of 2000/s and crash test of hat-shape column at 4m/s were conducted for steel sheets with tensile strength ranging from 290 to 980 MPa. Dynamic tensile strength increases with increasing static one but the ratio of dynamic tensile strength to static one decreases. Tensile strength remarkably affects crash energy absorption of column and TRIP steel is superior to other steels with same tensile strength. 7 refs., 16 figs., 1 tab.

  11. Report on the achievements in the projects subsidized by the Sunshine Project in fiscal 1981. Data 2. Development of a coal liquefaction technology - development of a solvent extraction and liquefaction technology - 'development of a brown coal based solvent extraction plant' (Development of a 50-t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 2). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    Developmental researches were carried out on a liquefaction plant for the Victoria brown coal produced in Australia (a 50-t/d pilot plant). In fiscal 1981, detailed design was performed on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the devices was procured, and the site construction was begun. The present data is a collection of drawings in relation with the machine design, such as the piping specifications, standard piping drawings, piping design procedures, piping drawings, pipe lists, and device inspection specifications. In relation with the instrumentation design, the instrumentation engineering specifications and meter lists. (NEDO)

  12. Report on the achievements in development of a coal liquefaction technology (a solvent extraction and liquefaction technology) in the Sunshine Project in fiscal 1981. Data 1. Development of a brown coal based solvent extraction plant (50 t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 1). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

    NONE

    1982-03-01

    This paper describes the data-1 for developing a brown coal based solvent extraction plant in the Sunshine Project in fiscal 1981. The data are for the development of a liquefaction plant for Victoria brown coal produced in Australia (a 50-t/d pilot plant). Fiscal 1981 has performed detailed design on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the machines and devices was procured, and the site construction was begun. Detailed design documents and drawings were prepared. The data collected in relation with the plant design included the followings: device lists, entire factory layout drawings, device arrangement drawings, process flow sheets, utility flow sheets (fuel gas and fuel oil systems, steam and condensate systems, air for instrumentation, plant air, cooling water supply and return, industrial water and treated water, a waste water treatment system, a nitrogen system, and a waste gas system), public pollution preventing facilities, hazardous location classifying plans, and material balances. The data collected in relation with the machine design included pressure vessel engineering specifications, heat exchanger engineering specifications, and device purchase specifications. (NEDO)

  13. Development of advanced corrosion resistant materials for molten coal ash; Yoyu sekitanbai ni taisuru kotaishokusei zairyo no kaihatsu

    NONE

    1997-03-01

    For development of materials for heat exchangers under severe corrosion environment due to ultra-high temperature coal combustion gas, basic data were surveyed. On the study in fiscal 1996, the corrosion resistance of one kind of commercially available material and 2 kinds of created materials was studied by coal slag coating test. The commercially available material was subjected to high- temperature corrosion tests of 1500 and 1550degC for a long time. The result showed that SiC is most excellent in the above temperature range. On new materials, 7 kinds of Cr2O3 system ceramics such as Cr2O3-Al2O3 system and Cr2O3- MgO system were selected considering high-temperature corrosion resistance, and the optimum composition and fabrication process of the new materials were studied. High- temperature corrosion tests, and measurement of thermal conductivity and thermal expansion were carried out for every specimen. The result suggested that some materials of Cr2O3- Al2O3 system are promising. 23 refs., 76 figs., 23 tabs.

  14. Report on results for fiscal 1996 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    NONE

    1997-12-01

    In fiscal 1996, the initial cooling test and rotary excitation test were conducted for the 70,000kW slow-response type model machine, with the basic characteristics of the rotor verified such as the cooling characteristics, shaft vibration characteristics, mechanical strength, and superconductivity stability, and with the results of the studies explained. The rotor of the 70,000kW slow-response type model was installed in the test site, and the field test was carried out in 1997. For this purpose, research test was performed by the element technology of the model machine and the partial model. The technological development items, trial manufacture and test items were field winding, multi cylindrical rotor and damper. Upon the test results using the element and partial model, the design and manufacturing were implemented of the superconducting generator of a slow-response type excitation method with the output of 70,000kW class. Performed were the basic characteristic test, long-term operation test and severity test on the assumption of abnormality, verifying the characteristics and reliability of the generator as well as obtaining data concerning an excessive electromagnetic force and heat generation. From the test data and the analysis/evaluation results obtained on the model machine, the 200,000kW class pilot machine was reviewed in the conceptual design. (NEDO)

  15. Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 1. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    NONE

    1998-09-01

    This report explains the outline as Part 1. In fiscal 1997, the 10th year of the project, a multi cylindrical rotary model for which an in-situ verification test was finished was brought back to the plant and dismantled for examination, while the in-situ verification test of a slow-response type model machine rotor was conducted in combination with a refrigeration system. In addition, in the research of AC wire materials and oxide based materials, studies were made with a purpose of high characterization and long wire materialization. In the metallic materials, a 10kANbTi conductor was developed while, in oxide-based materials, research was done on performance improvement and wire materialization based on various synthesizing methods. The manufacturing, factory test and in-situ text were conducted for a 70,000kW model machine with the purpose of R and D of a 200,000kW class pilot machine. Examination was made on the test method of the 70,000kW class model machine, operation technology of a superconducting generation system, and the effect of introducing the superconducting generator into a power system. In the conventional refrigeration system, a single unit test was carried out for the liquefaction, liquid storing capacity, etc., of the system. The 70,000kW class model machine was put through a test for confirming the general operation including the refrigeration system. (NEDO)

  16. Stainless steel rail, which is the first goods for JIS, is developed; Hatsu no JIS taiohin dearu sutenresureru wo kaihatsu

    NONE

    1999-08-15

    Daido Steel Co., Ltd. developed `the pond bottom rail` of the sewage disposal place and which is suitable for the gate door rail and so on, and tied up with Osaka steel manufacturing, and merchandised what was based on JIS in Japan for the first time. As for Daido Steel Co., Ltd.`s merchandising it, 3 kinds that it is called with rail of the weight 9kg 15kg 22kg. Though SUS 304 is a basis, quality of the material accepts production with SUS 316 which increased corrosions, SUS 304 N 2 of the high strength, and so on corresponding to the use for the user, too. Though Nippon Steel Corp. is producing an extreme small quantity at present by the pushing out method of construction, big says that the rail of the form that it is based on the JIS standard from the restriction of acid equipment and so on was merchandised as the stainless steel rail for the first time. Though the adoption of No. The 1st has already been decided as the pond bottom rail for the precipitation pond of the sewage disposal facilities 22kg by the stainless steel rail, substitution needs from the iron are opened up in the same company in an attraction and a crane, the rail for the elevator, the gate door rail, and so on during the water of the theme park. (translated by NEDO)

  17. Report of high efficiency waste power generation technology development in 1995; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (1995 nendo hokokusho)

    NONE

    1996-03-01

    High temperature and high pressure steam has been investigated for the high efficiency waste power generation technology development. The steam temperature below 300 centigrade is currently employed to avoid the corrosion of superheater, and the generating efficiency is less than 15%. Practical application of 500 centigrade and 100 kg/cm{sup 2} is planned by developing corrosion resistance materials. Environmental load reduction technology has been also developed. For the external circulation type fluidized bed furnace combustion tests using dummy waste in fiscal 1995, the temperature control at bag filter was effective for suppressing the dioxins. When using waste plastics, HCl could be reduced by blowing Ca compounds. Various Cr-Ni-Mo-based alloys have been developed as a corrosion resistance superheater tube material, and are currently tested. For the environmental load reduction technology, the development of pulse plasma exhaust gas treatment method has been continued from fiscal 1993. In fiscal 1995, this method was confirmed using a small-scale test unit, and also tested using a 5000 Nm{sup 3}/h bench-scale unit. The removal rates of dioxins at the outlet of bag filter were 99.8% and 99.3%, respectively. They were found to be affected greatly by the pulse waveform. 13 refs., 107 figs., 24 tabs.

  18. Achievement report for fiscal 1998 on the development of superconductor power application technology. 2. Research and development of superconducting wire and superconductive power generator, research of total system, research and development of refrigeration system, and verification test; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total sytsem no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

    NONE

    1999-03-01

    The slow excitation response type power generator is studied when the rotor and stator of a 70,000kW-class model are combinedly subjected to an on-site verification test, when a good result is obtained. The rotor is disassembled for inspection, and its members are found to be sound without any problem in terms of mechanical strength. The quick excitation response type is studied when a 70,000kW model is experimentally built and subjected to an on-site verification test after a rotation and excitation test in the factory, when the pilot machine concept design is reviewed. In the study of a total system, efforts continue for the review of the model machine test method, improvement on generator design and analytical methods, development of operating methods, and the effect of its introduction into the power system. Since a He-refrigerated system is requested to exhibit high reliability for application to power equipment and to be capable of continuous long-period operation, a system having constituents with their reliability enhanced and an appropriate redundant system is developed, and a verification study is under way which will continue for more than 10,000 hours. Described also is an oil-free low-temperature turbo refrigerator. The latest quick excitation response type rotor is also tested for verification. (NEDO)

  19. Development of simulator for studying formation process of crustal structure. 1; Chikaku kozo keisei simulator no kaihatsu. 1

    Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Murakami, Y.; Okubo, Y.; Matsubayashi, O.; Tanaka, A.; Nakajima, Y.; Morijiri, R. [Geological Survey of Japan, Tsukuba (Japan); Rokugawa, S. [The University of Tokyo, Tokyo (Japan)

    1997-05-27

    The purpose of this study is to combine seismic activity and volcanic activity by reproducing the formation process of the crustal structure from a physical viewpoint or developing as its extension a numerical simulator which can predict the future. The phenomenon to which attention is especially paid at present is a relation between the dynamic process and the thermal process in the domain including the crust or the upper mantle. Namely, to elucidate the formation process of the crust structure, diastrophism also including seismic activity, igneous activity, etc., it is important to evaluate effects of the behavior of heat supplied from the deep on the dynamic process. In the finite element method, it is not easy to make the effect of gravity reflect to the calculation for boundary conditions. Accordingly, it is general to pay attention to stress difference, considering that stress by gravity is in proportion to static rock pressure stress. Further, to realize interaction between the thermal process and the dynamic process, effects of thermal stress are expressed combining the heat conducting analysis and the plastic flow analysis. 3 refs., 7 figs.

  20. Development of on-line wall thickness gauge for small size seamless tube. Shokei seamless netsukan nikuatsukei no kaihatsu

    Okumura, T; Konya, N; Oka, H; Kasuya, T [Kawasaki Steel Corp., Tokyo (Japan)

    1991-03-01

    In order to heighten the accuracy of small size seamless tube wall thickness, hot wall thickness gauge was developed to be installed, immediately behind the finishing/rolling mill, for the on-line measurement, of which the method was by the parallel-beam transmissivity of gamma-ray. The measurement unit, aiming at flexible manufacturing system (FMS), is completely automated in correcting the accuracy, changing the sizes, etc. The damping characteristics of gamma-ray beam can be expressed by a characteristic function, taking the outside diameter and wall thickness of subject tube as parameters. The functional calculation, as based on measurement of transmitted quantity of gamma-ray through the three-dimensional steel material, changes, depending upon the outside diameter, wall thickness and material specification of subject tube. System was so applied as to calculate it therefore on a case-by-case basis. Though in the vicinity of tube end, the transmitted quantity of gamma-ray is largely influenced by the horizontal dislocation, that influence is slack in the middle part of tube. Therefore, the cross sectional division was made dense and sparse in the end part and middle part, respectively of tube, which division could diminish the error from several percent to less than 0.1%. The static noise was compressed by the optimized digital filter. That gauge is presently applied for the operational administration of small size seamless tube rolling. 2 refs., 11 figs., 2 tabs.