WorldWideScience

Sample records for kaeri sodium-water reaction

  1. Acoustic Leak Detection Testing Using KAERI Sodium-Water Reaction Signals for a SFR Steam Generator

    Kim, Tae-Joon; Jeong, Ji-Young; Kim, Jong-Man; Kim, Byung-Ho; Hahn, Do-Hee; Yugay, Valeriy S.

    2009-01-01

    The results of an experimental study of water in a sodium leak noise spectrum formation at 0.004-0.54 g/sec, various rates of water into a sodium leak, smaller than 1.0 g/sec, are presented. We focused on studying a micro leak detection with an increasing rate of water into sodium. On the basis of the experimental leak noise data manufactured in KAERI the simple dependency of an acoustic signal level from the rate of a micro and small leak at different frequency bands is presented to understand the principal analysis for the development of an acoustic leak detection methodology used in a K- 600 steam generator

  2. Sodium-water reaction product flow system

    Shirataki, K; Wada, H

    1978-11-18

    Purpose: To provide the subject equipments wherein thermal insulating layers which neither exfoliate nor react by the impact due to high temperature sodium and hydrogen gas and are used for mitigating the thermal impact are provided on the inner surfaces of the emission system equipments, thereby preventing the destruction of the emission system equipments. Constitution: Thermal insulating layers are formed on the inner surfaces of sodium-water reaction product emission system equipments, that is, the inner surface of the emission system pipeline, that of the accommodation vessel and the surface of the cyclone separator, by film treatment, coating or heat resisting coating, and these surfaces are covered with the layers. Each of the layers is made of a material which does not cause a rapid reaction with high temperature sodium or hydrogen gas nor exfoliates and is withstandable for several seconds in which the thermal impact of at least the emission system comes into question, and its thickness is more than one capable of securing the necessary thermal resistance computed by the thermal impact analysis of the emission system.

  3. Sodium-water reaction product flow system

    Shirataki, Koji; Wada, Hozumi.

    1978-01-01

    Purpose: To provide the subject equipments wherein thermal insulating layers which neither exfoliate nor react by the impact due to high temperature sodium and hydrogen gas and are used for mitigating the thermal impact are provided on the inner surfaces of the emission system equipments, thereby preventing the destruction of the emission system equipments. Constitution: Thermal insulating layers are formed on the inner surfaces of sodium-water reaction product emission system equipments, that is, the inner surface of the emission system pipeline, that of the accommodation vessel and the surface of the cyclone separator, by film treatment, coating or heat resisting coating, and these surfaces are covered with the layers. Each of the layers is made of a material which does not cause a rapid reaction with high temperature sodium or hydrogen gas nor exfoliates and is withstandable for several seconds in which the thermal impact of at least the emission system comes into question, and its thickness is more than one capable of securing the necessary thermal resistance computed by the thermal impact analysis of the emission system. (Yoshihara, H.)

  4. Large sodium water reaction calculations in a LMFBR steam generator

    Finck, P.; Lepareux, M.; Schwab, B.; Blanchet, Y.

    1986-05-01

    The French approach to the analysis of large and violent sodium water reactions is presented. The basis for choosing the Design Basis Accident is discussed. An energetical analysis of the physical phenomena involved stresses the specific needs for computing tools. The feature of these tools are then described, and a validation test is presented. Finally, industrial applications are described. 8 refs

  5. Theoretical Study of Sodium-Water Surface Reaction Mechanism

    Kikuchi, Shin; Kurihara, Akikazu; Ohshima, Hiroyuki; Hashimoto, Kenro

    Computational study of the sodium-water reaction at the gas (water) - liquid (sodium) interface has been carried out using the ab initio (first-principle) method. A possible reaction channel has been identified for the stepwise OH bond dissociations of a single water molecule. The energetics including the binding energy of a water molecule on the sodium surface, the activation energies of the bond cleavages, and the reaction energies, have been evaluated, and the rate constants of the first and second OH bond-breakings have been compared. It was found that the estimated rate constant of the former was much larger than the latter. The results are the basis for constructing the chemical reaction model used in a multi-dimensional sodium-water reaction code, SERAPHIM, being developed by Japan Atomic Energy Agency (JAEA) toward the safety assessment of the steam generator (SG) in a sodium-cooled fast reactor (SFR).

  6. Theoretical study of sodium-water surface reaction mechanism

    Kikuchi, Shin; Kurihara, Akikazu; Ohshima, Hiroyuki; Hashimoto, Kenro

    2012-01-01

    Computational study of the sodium-water reaction at the gas (water) - liquid (sodium) interface has been carried out using the ab initio (first-principle) method. A possible reaction channel has been identified for the stepwise OH bond dissociations of a single water molecule. The energetics including the binding energy of a water molecule on the sodium surface, the activation energies of the bond cleavages, and the reaction energies, have been evaluated, and the rate constants of the first and second OH bond-breakings have been compared. It was found that the estimated rate constant of the former was much larger than the latter. The results are the basis for constructing the chemical reaction model used in a multi-dimensional sodium-water reaction code, SERAPHIM, being developed by Japan Atomic Energy Agency (JAEA) toward the safety assessment of the steam generator (SG) in a sodium-cooled fast reactor (SFR). (author)

  7. Temperature dependence on sodium-water chemical reaction

    Tamura, Kenta; Deguchi, Yoshihiro; Suzuki, Koichi; Takata, Takashi; Yamaguchi, Akira; Kikuchi, Shin; Ohshima, Hiroyuki

    2012-01-01

    In a sodium-cooled fast reactor (SFR), liquid sodium is used as a heat transfer fluid because of its excellent heat transport capability. On the other hand, it has strong chemical reactivity with water vapor. One of the design basis accidents of the SFR is the water leakage into the liquid sodium flow by a breach of heat transfer tubes. This process ends up damages on the heat transport equipment in the SFR. Therefore, the study on sodium-water chemical reactions is of paramount importance for security reasons. This study aims to clarify the sodium-water reaction mechanisms using laser diagnostics. A quasi one-dimensional flame model is also applied to a sodium-water counter-flow reaction field. Temperature, H 2 , H 2 O, OH, Na and Particulate matter were measured using laser induced fluorescence and CARS in the counter-flow reaction field. The temperature of the reaction field was also modified to reduce the condensation of Na in the reaction zone. (author)

  8. Acoustic detection for small-leak sodium-water reaction

    Nei, Hiromichi; Ohshima, Iwao; Ujihara, Kozaburo; Hori, Masao

    1977-01-01

    Characteristics of acoustic signal produced by sodium-water reaction due to steam injection and by Ar gas injection into sodium were experimentally investigated. Acoustic signal was measured by using Kistler 808A and 815A5 accelerometers. Root mean square (RMS) measurements and frequency analysis of the signal were conducted. The RMS measurements could detect a small water leakage into sodium, as small as 0.07g/sec, in the present loop. The peaks in a frequency spectrum were caused by the natural vibration of a rod on which the acoustic transducer was mounted. The RMS was approximately proportional to the one-third power of the steam leak rate and increased to some extent with the ambient sodium temperature. RMS values, both for sodium-water reaction and Ar gas injection, were about the same order of magnitude, when the data were plotted against the volumetric flow rates of steam and Argas. (auth.)

  9. Sodium-water reaction test facility (SWAT-3)

    Shimazu, Hisashi; Ukechi, Kazutoshi; Sasakura, Kazutake; Kusunoki, Junichi

    1976-01-01

    In the development of the liquid metal cooled fast breeder reactor (LMFBR), the steam generator (SG) is considered one of the most important components. The Power Reactor and Nuclear Fuel Development Corporation (PNC) is now promoting the research and development of the SG system used with the prototype fast breeder reactor ''Monju''. In this research, the phenomena of the sodium-water reaction in the SG are the key which must be investigated for the solution of problems. The test facility (SWAT-3) simulating Monju's SG on the scale of 1/2.5 was designed, fabricated and installed by IHI at Oarai Engineering Center of PNC, its pre-operation being accomplished in February 1975. The purpose of SWAT-3 is summarized as follows: (1) To perform an overall test on the safety of Monju's SG and intermediate heat transport system under the design condition against sodium-water reaction accidents. (2) To investigate the damage of the SG structure caused by the sodium-water reaction, and the possibility of repair and recovery operations. The first test was accomplished successfully on June 9, 1975. As a result of the test, the fundamental function of this test facility was proven to be satisfactory as expected. (auth.)

  10. Sodium-water reaction in double pool LMFBR, (5)

    Yoshida, Kazuo; Kumagai, Hiromichi; Nishi, Yoshihisa; Uotani, Masaki

    1990-01-01

    Experiments were conducted using a 1/5 scale model of the Double Pool in order to evaluate a pressure rise caused by a large scale sodium-water reaction. The experiments were focused on the pressure rise caused by the piston motion of liquid sodium. It appeared from the results that the magnitude of this pressure rise depends on the depth of reaction point, and that a pressure rise more than 1 MPa would arise in the real Double Pool plant. A new design of steam generator is proposed to mitigate the pressure rise. (author)

  11. Sodium water reaction R and D for French LMFBR

    Cambillard, E.; Finck, P.; Lapicore, A.; Simeon, C.

    1985-01-01

    This paper presents the research and development which is underway for the French LMFBR steam generator safety study. The program comprises three major areas: (1) the analysis of realistic leaks, which includes the leak evolution and its consequences; (2) the response time of leak detection systems compared to leak propagation phenomena; and (3) the guillotine rupture (DBA) studies relative to source term evaluation by experimental/calculational approach and mechanical calculations. This program has provided information for the demonstrations of the steam generator safety in respect to a sodium-water reaction

  12. Analyses of hydrodynamic effects of large sodium-water reactions

    Sakano, K.; Shindo, Y.; Koishikawa, A.; Maekawa, I.

    1977-01-01

    Large leak sodium-water reactions that would occur in a steam generator of LMFBR causes abrupt changes of pressure and velocity of fluid in a secondary sodium system and relief system. This paper describes SOWACS-III together with its model and method. Results of analyses are also given, the comparison with experimental results of initial pressure spike being included. SOWACS-III treats the system which consists of the steam generator, vessel, valve, pump and pipe, and uses the following models and methods. (1) Components are assumed to be one-dimensional. (2) Pressure wave propagation near a reaction zone, where hydrogen is generated, is analyzed with the spherical co-ordinate (sphere-cylinder model). (3) A moving boundary is formed by contact of sodium with other fluid such as hydrogen and nitrogen. The boundary travels without mixing of sodium and another fluid through the boundary (boundary tracking model). The boundary can be treated not to move from the original place (fixed boundary model). (4) Pressure wave propagation is analyzed by the explicit method of characteristics in one-dimensional Eulerian co-ordinate. (5) Flow-induced force is analyzed by momentum balance. (6) The lateral motion of relief piping caused by the force is analyzed by NASTRAN code. Analyses were carried out for large sodium-water reaction experiments in SWAT-3 rig of PNC by using the sphere-cylinder model. The calculated pressure spike in the reaction vessel was compared with the measured one for a few milliseconds after water injection. The calculated value and measured one were 6.4 ata and 6.7 ata for peak pressure and 0.6 ms and 2.8 ms for rising time, respectively

  13. Reaction path analysis of sodium-water reaction phenomena in support of chemical reaction model development

    Kikuchi, Shin; Ohshima, Hiroyuki; Hashimoto, Kenro

    2011-01-01

    Computational study of the sodium-water reaction at the gas (water) - liquid (sodium) interface has been carried out using ab initio (first-principle) method. A possible reaction channel has been identified for the stepwise OH bond dissociations of a single water molecule. The energetics including the binding energy of a water molecule to the sodium surface, the activation energies of the bond cleavages, and the reaction energies, have been evaluated, and the rate constants of the first and second OH bond-breakings have been compared. The results are used as the basis for constructing the chemical reaction model used in a multi-dimensional sodium-water reaction code, SERAPHIM, being developed by JAEA toward the safety assessment of the steam generator (SG) in a sodium-cooled fast reactor (SFR). (author)

  14. Development of blow down and sodium-water reaction jet analysis codes-Validation by sodium-water reaction tests (SWAT-1R)

    Hiroshi Seino; Akikazu Kurihara; Isao Ono; Koji Jitsu

    2005-01-01

    Blow down analysis code (LEAP-BLOW) and sodium-water reaction jet analysis code (LEAP-JET) have been developed in order to improve the evaluation method on sodium-water reaction event in the steam generator (SG) of a sodium cooled fast breeder reactor (FBR). The validation analyses by these two codes were carried out using the data of Sodium-Water Reaction Test (SWAT-1R). The following main results have been obtained through this validation: (1) The calculational results by LEAP-BLOW such as internal pressure and water flow rate show good agreement with the results of the SWAT- 1R test. (2) The LEAP-JET code can qualitatively simulate the behavior of sodium-water reaction. However, it is found that the code has tendency to overestimate the maximum temperature of the reaction jet. (authors)

  15. Experimental and numerical reaction analysis on sodium-water chemical reaction field

    Deguchi, Yoshihiro; Takata, Takashi; Yamaguchi, Akira; Kikuchi, Shin; Ohshima, Hiroyuki

    2015-01-01

    In a sodium-cooled fast reactor (SFR), liquid sodium is used as a heat transfer fluid because of its excellent heat transport capability. On the other hand, it has strong chemical reactivity with water vapor. One of the design basis accidents of the SFR is the water leakage into the liquid sodium flow by a breach of heat transfer tubes. This process ends up damages on the heat transport equipment in the SFR. Therefore, the study on sodium-water chemical reactions is of paramount importance for security reasons. This study aims to clarify the sodium-water reaction mechanisms using an elementary reaction analysis. A quasi one-dimensional flame model is applied to a sodium-water counter-flow reaction field. The analysis contains 25 elementary reactions, which consist of 17 H_2-O_2 and 8 Na-H_2O reactions. Temperature and species concentrations in the counter-flow reaction field were measured using laser diagnostics such as LIF and CARS. The main reaction in the experimental conditions is Na+H_2O → NaOH+H and OH is produced by H_2O+H → H_2+OH. It is demonstrated that the reaction model in this study well explains the structure of the sodium-water counter-flow diffusion flame. (author)

  16. Wastage of Steam Generator Tubes by Sodium-Water Reaction

    Jeong, Ji Young; Kim, Jong Man; Kim, Tae Joon; Choi, Jong Hyeun; Kim, Byung Ho; Lee, Yong Bum; Park, Nam Cook

    2010-01-01

    The Korea Advanced LIquid MEtal Reactor (KALIMER) steam generator is a helical coil, vertically oriented, shell-and-tube type heat exchanger with fixed tube-sheet. The conceptual design and outline drawing of the steam generator are shown in Figure 1. Flow is counter-current, with sodium on the shell side and water/steam on the tube side. Sodium flow enters the steam generator through the upper inlet nozzles and then flows down through the tube bundle. Feedwater enters the steam generator through the feedwater nozzles at the bottom of steam generator. Therefore, if there is a hole or a crack in a heat transfer tube, a leakage of water/steam into the sodium may occur, resulting in a sodium-water reaction. When such a leak occurs, so-called 'wastage' is the result which may cause damage to or a failure of the adjacent tubes. If a steam generator is operated for some time in this condition, it is possible that it might create an intermediate leak state which would then give rise to the problems of a multi-target wastage in a very short time. Therefore, it is very important to predict these phenomena quantitatively from the view of designing a steam generator and its leak detection systems. For this, multi-target wastage tests for modified 9Cr-1Mo steel tube bundle by intermediate leaks are being prepared

  17. Sodium-water reaction studies for MONJU steam generators

    Hori, M.; Sato, M.; Nei, H.; Harasaki, T.; Hishida, M.; Saito, T.

    1975-01-01

    The R and D results of the PNC's sodium-water reaction project are reviewed. The purposes of the project with the specific object for each test rig and computer code are given. The test items which should be investigated for the safety evaluation of the MONJU steam generators are discussed, and the status of the PNC's work on each item is described. The results on the small-leak wastage measurement are shown and the improved experimental equations to predict the wastage rate from the leak rate and the sodium temperature are given. The preliminary results on the wastage of tube bundle in the intermediate leak range are shown. The depth and the area of the wastage and also the wastage rate for each tube are shown graphically. The measured peak value of the initial pressure spike for the large leak is shown. The scatter of the data and its causes are discussed. The bubble growth rate estimated from the void probe measurement is presented. The results of the simulation experiment on the pressure wave propagation to the secondary circuit are given, comparing them with the prediction by the one-dimensional computer codes SWAC-5K and SWAC-5H. (author)

  18. Sodium-water reaction studies for MONJU steam generators

    Hori, M; Sato, M; Nei, H; Harasaki, T; Hishida, M; Saito, T

    1975-07-01

    The R and D results of the PNC's sodium-water reaction project are reviewed. The purposes of the project with the specific object for each test rig and computer code are given. The test items which should be investigated for the safety evaluation of the MONJU steam generators are discussed, and the status of the PNC's work on each item is described. The results on the small-leak wastage measurement are shown and the improved experimental equations to predict the wastage rate from the leak rate and the sodium temperature are given. The preliminary results on the wastage of tube bundle in the intermediate leak range are shown. The depth and the area of the wastage and also the wastage rate for each tube are shown graphically. The measured peak value of the initial pressure spike for the large leak is shown. The scatter of the data and its causes are discussed. The bubble growth rate estimated from the void probe measurement is presented. The results of the simulation experiment on the pressure wave propagation to the secondary circuit are given, comparing them with the prediction by the one-dimensional computer codes SWAC-5K and SWAC-5H. (author)

  19. Development of LEAP-JET code for sodium-water reaction analysis. Validation by sodium-water reaction tests (SWAT-1R)

    Seino, Hiroshi; Hamada, Hirotsugu

    2004-03-01

    The sodium-water reaction event in an FBR steam generator (SG) has influence on the safety, economical efficiency, etc. of the plant, so that the selection of design base leak (DBL) of the SG is considered as one of the important matters. The clarification of the sodium-water reaction phenomenon and the development of an analysis model are necessary to estimate the sodium-water reaction event with high accuracy and rationality in selecting the DBL. The reaction jet model is pointed out as a part of the necessary improvements to evaluate the overheating tube rupture of large SGs, since the behavior of overheating tube rupture is largely affected by the reaction jet conditions outside the tube. Therefore, LEAP-JET has been developed as an analysis code for the simulation of sodium-water reactions. This document shows the validation of the LEAP-JET code by the Sodium-Water Reaction Test (SWAT-1R). The following results have been obtained: (1) The reaction rate constant, K, is estimated at between 0.001≤K≤0.1 from the LEAP-JET analysis of the SWAT-1R data. (2) The analytical results on the high-temperature region and the behaviors of reaction consumption (Na, H 2 O) and products (H 2 , NaOH, Na 2 O) are considered to be physically reasonable. (3) The LEAP-JET analysis shows the tendency of overestimation in the maximum temperature and temperature distribution of the reaction jet. (4) In the LEAP-JET analysis, the numerical calculation becomes unstably, especially in the mesh containing quite small sodium mass. Therefore, it is necessary to modify the computational algorism to stabilize it and obtain the optimum value of K in sodium-water reactions. (author)

  20. Sodium-Water Reaction approach and mastering for ASTRID Steam Generator design

    Saez, Manuel; Allou, Alexandre; Beauchamp, François; Bertrand, Carole; Rodriguez, Gilles; Menou, Sylvain; Prele, Gérard

    2013-01-01

    Conclusions: • Modular Steam Generator concept selected for ASTRID: → Brings flexibility for the expertise of failed modules after their removal; → Intrinsically limit the mechanical consequences of a postulated large Sodium-Water Reaction. • Sodium-Water-Air Reaction studies include both prevention and mitigation aspects, with dedicated tools to be developed through R&D. • Regarding Safety analysis, the possibility to move from the scenario of instantaneous failure of the whole Steam Generator tube bundle toward a scenario with sequenced failure needs to be investigated. • The Steam Generator is one of the key components in the Sodium-cooled Fast Reactor system for it provides an interface between sodium and water. The design objective for the Steam Generator is related to the improvement of mastering of Sodium-Water Reaction. • Potential Sodium-Water Reactions can be eliminated by adopting a Gas based Power Conversion System

  1. Application of laser diagnostics to sodium-water chemical reaction field

    Deguchi, Yoshihiro; Tamura, Kenta; Muranaka, Ryota; Kusano, Koji; Kikuchi, Shin; Kurihara, Akikazu

    2013-01-01

    In a sodium-cooled fast reactor (SFR), liquid sodium is used as a heat transfer fluid because of its excellent heat transport capability. On the other hand, it has strong chemical reactivity with water vapor. One of the design basis accidents of the SFR is the water leakage into the liquid sodium flow by a breach of heat transfer tubes in a steam generator. Therefore the study on sodium-water chemical reactions is of paramount importance for safety reasons. This study aims to clarify the sodium-water reaction mechanisms using laser diagnostics. The sodium-water counter-flow reactions were measured using laser diagnostics such as laser induced fluorescence, CARS, Raman scattering and photo-fragmentation. The measurement results show that the sodium-water reaction proceeds mainly by the reaction Na + H 2 O → NaOH + H and the main product is NaOH in this reaction. Its forward and backward reaction rates tend to balance with each other and the whole reaction rate reduces as temperature increases. (author)

  2. Adiabatic flame temperature of sodium combustion and sodium-water reaction

    Okano, Y.; Yamaguchi, A.

    2001-01-01

    In this paper, background information of sodium fire and sodium-water reaction accidents of LMFBR (liquid metal fast breeder reactor) is mentioned at first. Next, numerical analysis method of GENESYS is described in detail. Next, adiabatic flame temperature and composition of sodium combustion are analyzed, and affect of reactant composition, such oxygen and moisture, is discussed. Finally, adiabatic reaction zone temperature and composition of sodium-water reaction are calculated, and affects of reactant composition, sodium vaporization, and pressure are stated. Chemical equilibrium calculation program for generic chemical system (GENESYS) is developed in this study for the research on adiabatic flame temperature of sodium combustion and adiabatic reaction zone temperature of sodium-water reaction. The maximum flame temperature of the sodium combustion is 1,950 K at the standard atmospheric condition, and is not affected by the existence of moisture. The main reaction product is Na 2 O (l) , and in combustion in moist air, with NaOH (g) . The maximum reaction zone temperature of the sodium-water reaction is 1,600 K, and increases with the system pressure. The main products are NaOH (g) , NaOH (l) and H2 (g) . Sodium evaporation should be considered in the cases of sodium-rich and high pressure above 10 bar

  3. Energy balance and flow in steam generator part with sodium-water reaction

    Matal, O.

    1980-01-01

    Relations were derived for the calculation of heat liberated during the sodium water reaction in a tube failure in different parts of a steam generator. The results are graphically shown in i-T diagrams. Heat removal is described from the reaction zone to water and steam in undisturbed tubes and to the steam generator metal structure. (author)

  4. Development of computer code on sodium-water reaction products transport

    Arikawa, H.; Yoshioka, N.; Suemori, M.; Nishida, K.

    1988-01-01

    The LMFBR concept eliminating the secondary sodium system has been considered to be one of the most promissing concepts for offering cost reductions. In this reactor concept, the evaluation of effects on reactor core by the sodium-water reaction products (SWRPs) during sodium-water reaction at primary steam generator becomes one of the major safety issues. In this study, the calculation code was developed as the first step of the processes of establishing the evaluation method for SWRP effects. The calculation code, called SPROUT, simulates the SWRPs transport and distribution in primary sodium system using the system geometry, thermal hydraulic data and sodium-water reacting conditions as input. This code principally models SWRPs behavior. The paper contain the modelings for SWRPs behaviors, with solution, precipation, deposition and so on, and the results and discussions of the demonstration calculation for a typical FBR plant eliminating the secondary sodium system

  5. Acoustic sodium-water reaction detection of the Phenix steam generators

    Carminati, M.; Martin, L.; Sauzaret, A.

    1990-01-01

    The systems for acoustic sodium-water reaction detection and hydrogen detection of the Phenix steam generators as well as systems for monitoring signals analysis and processing are described. It is reported that the results obtained during operation and calibration phases are very encouraging and that industrial equipment showing the same performance are being examined. 6 figs

  6. Control of sodium fires and sodium-water reactions in breeder reactors

    Foerster, K.; Ruloff, G.; Voss, J.

    1985-01-01

    The excellent neutronic and thermodynamic properties of sodium as a fast-reactor coolant are somewhat counterbalanced by its high oxygen affinity. Because incidents like sodium fires and sodium-water reactions cannot be absolutely excluded, their effects and preventive measures have to be investigated. Characteristics and counter-measures are discussed. (orig.) [de

  7. Japanese position paper on sodium-water reaction testing and design

    Sato, M.; Hiroi, H.; Tanabe, H.; Miyake, O.; Kuroha, M.; Hoshi, Y.

    1984-01-01

    PNC has been developing the steam generator with helically coiled heat transfer tube bundle and downcommer tubes for the prototype fast reactor Monju since 1968. To establish the safety design against the sodium-water reaction accident was one of the most important R and D items at the start of the development. PNC started the experimental study initially in the large leak region in 1970. Until now, during twelve years, the experimental studies have been performed, which covers the phenomena from a micro leak to a large one, with the use of the SWAT-1 rig, SWAT-2 loop, SWAT-3 loop, and SWAT-4 rigs. The reliable leak detection system is necessary to minimize the damage by the sodium-water reaction. Two groups of efforts have been paid for developing the detection system. One is to develop the leak detector itself, and another is to grasp the hydrogen transport behavior in the sodium in the steam generator and the secondary piping system. Four sodium loops have been used for the development. The development of computer codes has also progressed in parallel with the sodium-water reaction experiments. Three codes have been accomplished for the design tools against the sodium-water reaction. Through the efforts mentioned above, sufficient experiences were obtained for designing and operating the Monju steam generator system

  8. Some conditions affecting the definition of design basis accidents relating to sodium/water reactions

    Bolt, P.R.

    1984-01-01

    The possible damaging effects of large sodium/water reactions on the steam generator, IHX and secondary circuit are considered. The conditions to be considered in defining the design basis accidents for these components are discussed, together with some of the assumptions that may be associated with design assessments of the scale of the accidents. (author)

  9. Prediction of metal wastage produced by sodium-water reaction jets

    Payne, J.F.B.

    1979-01-01

    When a leak occurs in a sodium heated boiler, a sodium-water reaction jet is formed which causes further damage to the boiler, ie wastage. A correlation is developed which predicts wastage of ferritic steel boiler tubes for the range of leak sizes, sodium temperatures and leak to target spacing for which data available. (author)

  10. Design of the US-CRBRP sodium/water reaction pressure relief system

    Kruger, G.B.; Murdock, T.B.; Rodwell, E.; Sane, J.O.

    1976-01-01

    Protection against intermediate sodium system overpressure from the sodium/water reaction associated with large leaks within the CRBRP Steam Generators is provided by the sodium/water reaction pressure relief system (SWRPRS). This system consists of rupture disks connected to the intermediate sodium piping adjacent to the inlet to the superheater and outlet from the evaporator modules. The rupture discs relieve into piping that leads to reaction produce separator tanks, which in turn are vented to a centrifugal separator and flare stack arranged to burn hydrogen gas exhausting into the atmosphere. Analyses have been conducted using the TRANSWRAP Computer Code to predict the system pressures and flow rates during the large leak event. Experimental tests to be conducted in the large leak test rig (LLTR) will be used to confirm the analysis techniques used in the design

  11. Pressure transients resulting from sodium-water reaction following a large leak in LMFBR steam generator

    Rajput, A.K.

    1984-01-01

    The study of sodium water reaction, following a large leak, concerns primarily with the estimation of pressure/flow transients that are developed in the steam generator and the associated secondary circuit. This paper describes the mathematical formulations used in SWRT (Sodium Water Reaction Transients) code developed to estimate such pressure transients for FBTR plant. The results, obtained using SWRT have been presented for a leak in economiser (20m from bottom water header) and for a leak in super heater portions. A time lag of 50 m sec was considered for rupture disc takes to burst once the pressure experienced by it exceeds the set value. Also described in annexure to this paper is the mathematical formulation for two phase transient flow for the better estimation of leak rate from the ruptured end of the damaged heat transfer tube. This leak model considers slip but assumes thermal equilibrium between the liquid and vapour phases

  12. Experiences on removal of sodium-water reaction products in SWAT-3

    Tanabe, H.; Hiroi, H.; Sato, M.; Otaka, J.

    2002-01-01

    This report summarizes experiences and information concerning the removal of sodium water reaction products (SMRP) obtained through large leak tests of the Steam Generator Safety Test Facility (SWAT-3) at PNC/OEC, which were conducted to validate the safety design of steam generators of a prototype LMFBR Monju. The following three problems are discussed here: (1) drainability of SWRP, (2) removal of SWRP by using a cold trap, and (3) steam cleaning of SWRP. (author)

  13. A fundamental study on sodium-water reaction in the double-pool-type LMFBR

    Yoshida, Kazuo; Akimoto, Tokuzo

    1987-01-01

    In order to evaluate the pressure rise by large sodium-water reaction in the Double-Pool LMFBR, basic tests on pressure wave celerity in rectangular tube are carried out. The initial spike pressure in rectangular-shelled steam generator of the Double Pool reactor, strongly depends on pressure wave celerity. In this study, celerity was measured as a function of pressure wave rising time and pulse height, and influence of water around the test section on celerity was investigated. (author)

  14. Improvement on reaction model for sodium-water reaction jet code and application analysis

    Itooka, Satoshi; Saito, Yoshinori; Okabe, Ayao; Fujimata, Kazuhiro; Murata, Shuuichi

    2000-03-01

    In selecting the reasonable DBL on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on sodium-water reaction (SWR) jet code (LEAP-JET ver.1.30) and application analysis to the water injection tests for confirmation of code propriety were performed. On the improvement of the code, a gas-liquid interface area density model was introduced to develop a chemical reaction model with a little dependence on calculation mesh size. The test calculation using the improved code (LEAP-JET ver.1.40) were carried out with conditions of the SWAT-3·Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results and the influence to analysis result of a model are reasonable. For the application analysis to the water injection tests, water injection behavior and SWR jet behavior analyses on the new SWAT-1 (SWAT-1R) and SWAT-3 (SWAT-3R) tests were performed using the LEAP-BLOW code and the LEAP-JET code. In the application analysis of the LEAP-BLOW code, parameter survey study was performed. As the results, the condition of the injection nozzle diameter needed to simulate the water leak rate was confirmed. In the application analysis of the LEAP-JET code, temperature behavior of the SWR jet was investigated. (author)

  15. Sodium/water reactions in steam generators of liquid metal fast breeder reactors

    Hori, M.

    1980-01-01

    The status of the research and development on sodium/water reactions resulting from the leakage of water into sodium in LMFBR steam generators is reviewed. The importance of sodium/water reaction phenomena in the design and operation of steam generators is discussed. The effects of sodium/water reactions are evaluated and methods of protection against these phenomena are surveyed. The products of chemical reactions between sodium and water under steam generator conditions are H 2 , NaOH, Na 2 O and NaH. Together with the temperature rise due to the associated exothermic reaction, these reaction products cause effects such as self-wastage, single- and multi-target wastage, and rapid pressure increase, depending on the size of the leak hole or the magnitude of leak rate. As for the wastage phenomena of small leaks, the effects of various factors have been studied and experimental correlations, as well as some theoretical work, have been performed. To investigate the pressure phenomena of a large leak, large-scale tests have been conducted by various organizations, and the computer codes to analyse these phenomena have been developed and verified by experiments. In the design of steam generators, an initial failure up to a hypothetical double-ended guillotine rupture of a single heat transfer tube is widely used as the design basis leak. Protection systems for LMFBR plants consist of leak detection devices, leak termination devices, and reaction pressure relief devices. From analyses based on research and development activities, as well as from experience with leaks in steam generator test loops and reactor plants, it has been confirmed that protection systems can satisfactorily be designed to accommodate leak incidents in LMFBR plants. (author)

  16. Corrosion of Steels in the Vicinity of a Sodium-Water Reaction

    Davies, R. A.; Bray, J. A.; Lyons, J. M. [U.K. Atomic Energy Authority, Dounreay Experimental Reactor Establishment, Thurso, Caithness (United Kingdom)

    1967-06-15

    Rapid corrosion of steels in the vicinity of a sodium-water reaction could lead to a major reaction in a sodium-water heat exchanger. An investigation of the magnitude of the corrosion problem has been carried out under conditions simulating both a small water leak and a full size pipe burst, and further tube failures have been obtained. These experiments were carried out on a sodium rig which could accommodate simple full-scale models of sections of heat exchanger, and up to 70 lb of water was injected into 700 lb of sodium in 9.0s. The corrosion phenomena have also been investigated on a small scale under more controllable conditions by pumping water at normal pressures into a pot of sodium. With a flow-rate of 1 ml/min corrosion rates in excess of 0.005 in./min have been obtained. The effect of various parameters on the corrosion rate has been studied, and a comparison has been made of the corrosion rates obtained with a variety of steels. The corrosion appears to be a direct result of conditions during the reaction, and the appearance of the specimen and pattern of damage suggests that the main effect is concentrated where the sodium water reaction front impinges on the metal surface. The corrosion rates are very much lower with stainless steel and nickel alloys than with ferritic materials, and suggest that the phenomena are associated with the formation of (Na{sub 2}O){sub 2}FeO. Iron powder has also been observed in the vicinity of the reaction which would suggest that this is reduced at a later stage, either as a result of the hydrogen produced during reaction, or by thermal cycling. (author)

  17. Fundamental study on temperature estimation of steam generator tubes at sodium-water reaction

    Furukawa, Tomohiro; Yoshida, Eiichi

    2008-11-01

    In case of the tube failure in the steam generator of the sodium cooled fast breeder reactor, its adjoined tubes are rapidly heated up by the chemical reaction between sodium and water/steam. And it is known that the tubes have the damage called 'wastage' by the disclosure steam jet. This research is a fundamental study based on the metallography about temperature estimation of the damaged tubes at the sodium-water reaction for the establishment of mechanism analysis technique of the behavior. In the examination, the material which gave the rapid thermal history which imitated sodium-water reaction was produced. And it was investigated whether the thermal history (i.e. maximum temperature and the holding time) of the samples could be presumed from the metallurgical examination of the samples. The major results are as follows: (1) The microstructure of the sample which was given the rapid thermal heating has reserved the influence of the maximum temperature and the time, and the structure can explain by referring to the equilibrium diagram and the continuous cooling transformation diagram. (2) Results of the electrolytic extraction of the samples, the ratio of the remained volume to the electrolyzed volume degreased with the increase of the maximum temperature and the time. Furthermore, it was observed the correlation between the remained volume of each element (Cr, Mo, Fe, V and Nb) and the thermal history. (3) It was obtained that the thermal history of the tubes damaged by sodium-water reaction might be able to be estimated from the metallurgical examinations. (author)

  18. Small leak detection by measuring surface oscillation during sodium-water reaction in steam generator

    Nei, Hiromichi; Hori, Masao

    1977-01-01

    Small leak sodium-water reaction tests were conducted to develop various kinds of leak detectors for the sodium-heated steam generator in FBR. The super-heated steam was injected into sodium in a reaction vessel having a sodium free surface, simulating the steam generator. The level gauge in the reaction vessel generated the most reliable signal among detectors, as long as the leak rates were relatively high. The level gauge signal was estimated to be the sodium surface oscillation caused by hydrogen bubbles produced in sodium-water reaction. Experimental correlation was derived, predicting the amplitude as a function of leak rate, hydrogen dissolution ratio, bubble rise velocity and other parameters concerned, assuming that the surface oscillation is in proportion to the gas hold-up. The noise amplitude under normal operation without water leak was increased with sodium flow rate and found to be well correlated with Froud number. These two correlations predict that a water leak in a ''MONJU'' class (300 MWe) steam generator could possibly be detected by level gauges at a leak rate above 2 g/sec. (auth.)

  19. SWAAM-LT: The long-term, sodium/water reaction analysis method computer code

    Shin, Y.W.; Chung, H.H.; Wiedermann, A.H.; Tanabe, H.

    1993-01-01

    The SWAAM-LT Code, developed for analysis of long-term effects of sodium/water reactions, is discussed. The theoretical formulation of the code is described, including the introduction of system matrices for ease of computer programming as a general system code. Also, some typical results of the code predictions for available large scale tests are presented. Test data for the steam generator design with the cover-gas feature and without the cover-gas feature are available and analyzed. The capabilities and limitations of the code are then discussed in light of the comparison between the code prediction and the test data

  20. Test results of sodium-water reaction testing in near prototypical LMR steam generator

    Boardman, C.E.; Hui, M.; Neely, H.H.

    1990-01-01

    An extensive test program has been performed in the United States to investigate the effects of large sodium-water reaction events in LMFBR steam generators. Tests were conducted in the Large Leak Test Rig (LLTR) located at the Energy Technology Engineering Center (ETEC). The program was divided into two phases, Series I and Series II, for the purpose of satisfying near-term and long-term needs. Series II was further subdivided into large and intermediate leak tests. This paper will emphasize the Series II intermediate leak tests and resulting conclusions for steam generator design and operation. 11 figs, 2 tabs

  1. Large scale sodium-water reaction tests for Monju steam generators

    Sato, M.; Hiroi, H.; Hori, M.

    1976-01-01

    To demonstrate the safe design of the steam generator system of the prototype fast reactor Monju against the postulated large leak sodium-water reaction, a large scale test facility SWAT-3 was constructed. SWAT-3 is a 1/2.5 scale model of the Monju secondary loop on the basis of the iso-velocity modeling. Two tests have been conducted in SWAT-3 since its construction. The test items using SWAT-3 are discussed, and the description of the facility and the test results are presented

  2. Analysis of the Sodium-Water Reaction Phenomena by Small Water/Steam Leaks

    Jeong, J-Y; Kim, T-J; Kim, J-M; Kim, B-H; Park, N-C

    2006-01-01

    One of the important problems to be solved in the design and construction of a sodium cooled fast reactor is to confirm the safety and reliability of the steam generator which transfers the heat from the sodium to the water. Sodium-water reaction events may occur when material faults such as a pinhole or cracks occur in the heat transfer tube wall. When such a leak occurs, evaporating water or superheated steam enters through a small leak into the sodium. The surface of this steam jet reacts with the surrounding sodium. Due to turbulence, sodium and particles of the reaction products are drawn at a high velocity into the jet. Impingement of these particles on an adjacent tube is followed by a combined process of a corrosion and erosion which results in a local weakening of the affected tube. If there is no reliable detection available in time, wastage will ultimately result in an additional leak in the adjacent tube. Therefore, it is very significant to predict these phenomena quantitatively from the view of designing a steam generator and its leak detection systems. The objective of this study is a basic investigating of the sodium-water reaction phenomena by small water/steam leaks

  3. The improvement of the heat transfer model for sodium-water reaction jet code

    Hashiguchi, Yoshirou; Yamamoto, Hajime; Kamoshida, Norio; Murata, Shuuichi

    2001-02-01

    For confirming the reasonable DBL (Design Base Leak) on steam generator (SG), it is necessary to evaluate phenomena of sodium-water reaction (SWR) in an actual steam generator realistically. The improvement of a heat transfer model on sodium-water reaction (SWR) jet code (LEAP-JET ver.1.40) and application analysis to the water injection tests for confirmation of propriety for the code were performed. On the improvement of the code, the heat transfer model between a inside fluid and a tube wall was introduced instead of the prior model which was heat capacity model including both heat capacity of the tube wall and inside fluid. And it was considered that the fluid of inside the heat exchange tube was able to treat as water or sodium and typical heat transfer equations used in SG design were also introduced in the new heat transfer model. Further additional work was carried out in order to improve the stability of the calculation for long calculation time. The test calculation using the improved code (LEAP-JET ver.1.50) were carried out with conditions of the SWAT-IR·Run-HT-2 test. It was confirmed that the SWR jet behavior on the result and the influence to the result of the heat transfer model were reasonable. And also on the improved code (LEAP-JET ver.1.50), user's manual was revised with additional I/O manual and explanation of the heat transfer model and new variable name. (author)

  4. Wastage Behavior of Modified 9Cr-1Mo Steel Tube Material by Sodium-Water Reaction

    Jeong, Ji Young; Kim, Jong Man; Kim, Tae Joon; Choi, Jong Hyeun; Kim, Byung Ho; Park, Nam Cook

    2009-01-01

    The development of a sodium-heated steam generator with safety and reliability is an essential requirement from the viewpoint of the economic efficiency of a sodium-cooled fast reactor. In most cases, these steam generators, which are in the process of development or operating, are of a shell-in tube type, with a high pressure water/steam inside the tubes and low pressure sodium on the shell-side, with a single wall tube as a barrier between these fluids. Therefore, if there is a hole or a crack in a heat transfer tube, a leakage of water/steam into the sodium may occur, resulting in a sodium-water reaction. When such a leak occurs, so-called 'wastage' is the result which may cause damage to or a failure of the adjacent tubes. If a steam generator is operated for some time in this condition, it is possible that it might create an intermediate leak state which would then give rise to the problems of a multi-target wastage in a very short time. Therefore, it is very important to predict these phenomena quantitatively from the view of designing a steam generator and its leak detection systems. The objective of this study is a basic investigating of the sodium-water reaction phenomena by small water/steam leaks. For this, wastage tests for modified 9Cr-1Mo steel were conducted

  5. Large-leak sodium-water reaction analysis for steam generators

    Sakano, K; Shindo, Y; Hori, M

    1975-07-01

    The guillotine rupture of 4 tubes is assumed as a design basis regarding the large-leak sodium-water reaction in the system of the MONJU steam generator. Three kinds of analyses were performed with the view to showing the integrity of the steam generator system on the reaction. The first one is the analysis of the initial pressure spike, assuming the initial guillotine rupture of 1 tube. The analysis was performed by utilizing one-dimensional sphere-cylinder model code SWAC-7 and two-dimensional axisymmetric code PISCES 2DL. The second one is the analysis of the secondary peak pressure and its propagation in the system, assuming the instantaneous guillotine rupture of 4 tubes. The third one is the analysis of the dynamic deformation of the steam generator shell. The integrity of the steam generator system was shown by the analyses. (author)

  6. Large-leak sodium-water reaction analysis for steam generators

    Sakano, K.; Shindo, Y.; Hori, M.

    1975-01-01

    The guillotine rupture of 4 tubes is assumed as a design basis regarding the large-leak sodium-water reaction in the system of the MONJU steam generator. Three kinds of analyses were performed with the view to showing the integrity of the steam generator system on the reaction. The first one is the analysis of the initial pressure spike, assuming the initial guillotine rupture of 1 tube. The analysis was performed by utilizing one-dimensional sphere-cylinder model code SWAC-7 and two-dimensional axisymmetric code PISCES 2DL. The second one is the analysis of the secondary peak pressure and its propagation in the system, assuming the instantaneous guillotine rupture of 4 tubes. The third one is the analysis of the dynamic deformation of the steam generator shell. The integrity of the steam generator system was shown by the analyses. (author)

  7. Analyses for experiment on sodium-water reaction temperature by the CHAMPAGNE code

    Yoshioka, Naoki; Kishida, Masako; Yamada, Yumi

    2000-03-01

    In this work, analyses on sodium-water reaction temperature in the new SWAT-1(SWAT-1R) test were completed by the CHAMPAGNE code in order to understand void and velocity distribution in sodium system, which was difficult to be measured in experiments. The application method of the RELAP5/Mod2 code was investigated to LMFBR steam generator (SG) blow down analysis, too. The following results were obtained. (1) Analyses on sodium-water reaction temperature in the SWAT-1R test. 1) Analyses were carried out for the SWAT-1R test under the condition water leak rate 600 g/s by treating the pressure loss coefficient, the interface friction coefficient and the coefficient related to reaction rate as parameters. The effect and mechanism of each parameter on the shape of reaction zone were well understood by these analyses. 2) The void and velocity distribution in sodium system were estimated by use of the most suitable parameters. These analytical results are expected to be useful for planning of the SWAT-1R test and evaluation of test result. (2) Investigation of the RELAP5/Mod2 code. 1) The items to be improved in the RELAP5/Mod2 code were clarified to apply this code to the FBR SG blow down analysis. 2) One of these items was an addition of the shell-side (sodium-side) model. A sodium-side model was designed and added to the RELAP5/Mod2 code. Test calculations were carried out by this improved code and the basic function of this code was confirmed. (author)

  8. An experimental study on sodium-water reaction in the double pool LMFBR, (4)

    Kumagai, Hiromichi; Yoshida, Kazuo; Uotani, Masaki; Akimoto, Tokuzo

    1989-01-01

    Double Pool type LMFBR set the rectangular cross-sectional steam generator (SGs) inside a secondary vessel. The initial spike pressure rise caused by large sodium-water reaction in SGs might be radiated into a large sodium pool in the secondary vessel. Therefore basic experiments on pressure wave propagation were carried out by generating pressure wave in water by mean of a set of drop hummer and piston. But the experimental apparatus in water was not convenience to simulate the structure near the bottom end of the SGs shell. In this reports, experiments were carried out by generating pulse sound pressure in air, and compared with the results pressure waves in water. (author)

  9. Experimental investigation of solid sodium-water reaction: tests results and phenomenological analysis

    Daudin, K.; Beauchamp, F.; Proust, C.

    2014-01-01

    Sodium-Water Reaction (SWR) is an issue one has to be capable to deal with for the next generation of nuclear reactors (SFR for GEN IV). The background of these experiments is the improvement of safety demonstration regarding SWR in an open volume. This experimental campaign is conducted at the CEA Cadarache inside a cylindrical reactor filled with inert gas. The sodium is inside a loading pot and water comes into contact by immersion. SWR and its physical effects are followed by different pressure and temperature sensors. The results show a limit to the overpressure increasing sodium mass. Global assessment of physical effects of SWR contributes to put forward the relative nature of phenomena with geometric configuration, and the importance of scale effects. (authors)

  10. Evaluation of heat transfer tube failure propagation due to sodium-water reaction in steam generator

    Nei, Hiromichi

    1978-01-01

    An evaluation was made of heat transfer tube failure propagation due to sodium-water reaction wastage in a sodium heated steam generator, by comparing an empirically derived wastage equation with leak detector responses. The experimental data agreed well with the wastage equation even for different values of distance-to-nozzle diameter ratio, though the formula had been based on wastage data obtained for only one given distance. The time taken for failure propagation was estimated for a prototype steam generator, and compared with the responses characteristics of acoustic detectors and level gages. It was found that there exists a range of leak rate between 0.5 and 100 g/sec, where the level gage can play a useful role in leak detection. The acoustic detector can be expected to respond more rapidly than the cover gas pressure gage, if noise is kept below ten times the value observed in an experimental facility, SWAT-2. (auth.)

  11. SNR-steam generator design with respect to large sodium water reactions

    Jong, J.J. de; Kellner, A.; Florie, C.J.L.

    1984-01-01

    This paper deals with the experiences gained during the licensing procedure for the steam generators for the SNR 300 LMFBR regarding large sodium-water reactions. A description is given of the different calculations executed to investigate the effects of large leaks on the 85 MW helical coiled and straight tube steam generators. The investigations on the helical coiled steam generators are divided in the formulations of fluid behaviour, dynamic force calculations, dynamic response calculation and finally stress analyses. Several results are shown. The investigations on the straight tube steam generators are performed using models describing fluid-structure interaction, coupled with stress analyses. Several results are presented. A description is given of the problems and necessary construction changes during the licensing process. Advises are given for future analyses and design concepts for second generation commercial size LMFBR steam generators with respect to large leaks; based on the experience, gained with SNR 300, and using some new calculations for SNR 2. (author)

  12. Unsteady aspects of sodium-water reaction. Water clearing of sodium containing equipments

    Carnevali, Sofia

    2012-01-01

    Sodium fast Reactor (FSR) is one of the most promising nuclear reactor concepts in the frame of Generation IV Systems to be commercialised in the next decades. One important safety issue about this technology is the highly exothermal chemical reaction of sodium when brought in contact with liquid water. This situation is likely, in particular during decommissioning, when sodium needs to be firstly converted ('destroyed') into non-reactive species. This is achieved by water washing: the major products are then gaseous hydrogen and corrosive soda. Today, such operations are performed in confined chambers to mitigate the consequences of any possible abnormal conditions. It has for long been believed that the main safety problem was the combustion of hydrogen in the surrounding air despite some pioneering works suggested that even without air the reaction could be explosive. It is extremely important to clarify the phenomenology of sodium-water interactions since available knowledge does not allow a robust extrapolation of existing data/model to full scale plants. The primary objective of this work is to identify and assess the details of the phenomenology, especially at the sodium/water interface, to isolate the leading mechanisms and to propose a robust and innovative modelling approach. A large body of yet unreleased experimental data extracted from the files of the French Commissariat a l'Energie Atomique (CEA) was collated and analysed on the basis of 'explosion' physics. Some additional experiments were also performed to fill some gaps, especially about the kinetics of the reaction. The results strongly suggest that the fast expansion of gas producing a blast wave in certain conditions is a kind of vapour explosion. It also appears that any potential hydrogen-air explosion should be strongly mitigated by the large quantity of water vapour emanating also from the reaction zone. The limitations of existing modelling approaches are clearly

  13. Ultrasonic inspection for wastage in the LMFBR steam generator due to sodium--water reactions

    Neely, H.H.; Renger, L.

    1977-01-01

    As part of a program to study the results of large sodium-water reactions in the LMFBR Steam Generator, a boreside ultrasonic inspection device was developed to measure the wall thickness and diameter of the 2- 1 / 4 Cr-1 Mo, 0.397 in. I.D. steam tubes. The reaction was created in a near prototype steam generator by guillotine-type rupture of a steam tube, while the generator was at operating conditions. Wastage occurred on the surrounding tubes due to the high temperature reaction. The UT test instrument was designed to operate with a 15 MHz transducer in the pulse-echo shear-wave mode, with a sampling rate of 10 4 /sec. System outputs are diameter, wall thickness, attitude and axial position of the transducer. All are displayed digitally and may be recorded. Measurements are fed into a computer for later retrieval, and/or cascaded outputs into an x-y recorded displaying either out-of-limit or thickness data. The UT data taken in this experiment were consistent with physical measurements on a tube which was removed from the generator after the test. A machined flat 1 / 8 -inch long and 0.002-inch deep could readily be detected

  14. Experimental and theoretical investigations on safety of the SNR - straight-tube design steam generator with sodium-water reactions

    Dumm, K.; Sauermann, F.; Schnitker, W.; Welter, A.

    A number of large sodium-water reaction tests has been performed in a steam generator model in order to verify the layout criteria of the SNR straight-tube design steam generators under accident conditions. The experimental setup is described. The test results and their applicability to the SNR steam generators are given and discussed. (U.S.)

  15. Thermal analysis experiment for elucidating sodium-water chemical reaction mechanism in steam generator of sodium-cooled fast reactor

    Kikuchi, Shin; Kurihara, Akikazu; Ohshima, Hiroyuki

    2012-01-01

    For the purpose of elucidating the mechanism of the sodium-water surface reaction in a steam generator of sodium-cooled fast reactors, kinetic study of the sodium (Na)-sodium hydroxide (NaOH) reaction has been carried out by using Differential Thermal Analysis (DTA) technique. The parameters, including melting points of Na and NaOH, phase transition temperature of NaOH, Na-NaOH reaction temperature, and decomposition temperature of sodium hydride (NaH) have been identified from DTA curves. Based on the measured reaction temperature, rate constant of sodium monoxide (Na 2 O) generation was obtained. Thermal analysis results indicated that Na 2 O generation at the secondary overall reaction should be considered during the sodium-water reaction. (author)

  16. A fundamental study on sodium-water reaction in the double pool LMFBR, (3)

    Uotani, Masaki; Kumagai, Hiromichi; Nishi, Yoshihisa; Yoshida, Kazuo

    1989-01-01

    The double pool LMFBR is an innovative reactor that Central Research Institute of Electric Power Industry proposed for the purpose of reducing the construction cost of FBRs, and it is characterized by immersing steam generators in the annular plenum formed between the primary vessel and the outer secondary vessel. Therefore, it is expected that the pressure behavior at the time of sodium-water reaction due to the breaking of heating tubes is largely different from the case of steam generators of conventional FBRs. In order to ensure the soundness of the primary vessel that containes the reactor core, it is necessary to sufficiently grasp the pressure behavior in the plenum, and this basic experiment and analysis are related to the pressure behavior due to piston motion that arises in the initial period of quasi-steady pressure. About 1/10 scale annular plenum was used, and the generation of reaction product gas was simulated by the release of nitrogen. When gas was released in the plenum, the highest pressure rise occurred in the initial period of release, and thereafter, periodic variation arose. The pressure waveform and the value of pressure rise as the results of the model analysis agreed well with the measured results. (K.I.)

  17. Analysis of acoustic data from UK sodium/water reaction test facilities

    Rowley, R.; Mcknight, J.A.; Airey, J.

    1990-01-01

    This paper describes acoustic measurements made during a number of sodium/water reaction experiments in the UK. The tests have included water and steam injections through both realistic (fatigue crack) defects and machined orifices and have covered a range of experimental conditions including those appropriate to the inlet and outlet regions of the EFR steam generators. Injection rates were typically in the range 0.1 to 30 g/s. Where possible, gas injections were also included in the test programme for comparison, since it is anticipated that a practical SGU acoustic leak detection system would include a facility for gas injections to allow system calibration, and to confirm transmission properties within the SGU. The test sections were instrumented with accelerometers on waveguides and in some cases included an under-sodium microphone situated about 300mm above the reaction zone. Tape recordings were made during the tests and used for detailed analysis off-line, although an audible output from one of the acoustic channels was used to monitor the progress of the injections and provide information for the rig operators. A comparison of the signal amplitudes measured during the experiments with typical reactor background noise was made and an estimate of the detection sensitivity of an acoustic monitoring system was deduced. 3 refs, 5 figs, 1 tab

  18. Numerical thermal-hydraulics study on sodium-water reaction phenomena

    Takashi, Takata; Akira, Yamaguchi

    2003-01-01

    A new computational program SERAPHIM (Sodium-watEr Reaction Analysis: PHysics of Interdisciplinary Multi-phase flow) is developed to investigate the Sodium-Water Reaction (SWR) phenomena based on parallel computation technology. A compressible three-fluid (liquid water, liquid sodium and mixture gas) and one-pressure model is adopted for multi-phase calculation. The Highly Simplified Maker And Cell (HSMAC) method considering with compressibility is implemented as the numerical solution. The Message-Passing Interface (MPI) is used for the parallel computation. Two types of reactions are considered for the SWR modeling; one is a surface reaction and the other is a gas phase reaction. The surface reaction model assumes that liquid sodium reacts with water vapor on the surface of liquid sodium. An analogy of heat transfer and mass transfer is applied in this model. Reaction heating vaporizes liquid sodium resulting in the gas phase reaction. The ab initio molecular orbital method is applied to investigate the reaction mechanism and evaluate the reaction rate described by the Arrhenius law. A performance of parallel computation is tested on the cluster-PC (16 CPUs) system. The execution time becomes 17.1 times faster in case of 16 CPUs. It seems promising that the SERAPHIM code is practicable for large-scale analysis of the SWR phenomena. Three-dimensional SWR analyses are also carried out to investigate the characteristics of the thermal-hydraulics with the SWR and an influence of initial pressure (0.2 MPa and 0.6 MPa) on an early stage of the SWR phenomenon. As a result, distribution of a gas region, in which water vapor or product of the SWR such as hydrogen and sodium hydroxide exits, velocity and high temperature region differs by 0.2 MPa and 0.6 MPa conditions. However, the maximum gas temperature has an upper bounding and is almost constant both in the analyses. The reason of the upper bounding is attributed to the fact that a hydrogen gas covers up a liquid

  19. Sodium/water reaction detection confirmation and location with time domain beam former

    Cornu, C.

    1997-01-01

    The CEA studied the validity of a time beamforming method for the detection and location of Sodium/water reaction in steam generators of breeder reactors. In the context of the RCM, we apply this method on recorded data during a water injection in Sodium in ASB loop, artificially mixed with PFR background. Despite the severity of experiment conditions (the signal to noise ratio is between -6 and -24 dB). We show that the employed method completed with a low frequency pass band filter allows us to locate the injection with a precision of 30% of the diameter of the loop. Using the method in the course of time allows us to coarsely locate the start time and the duration of the leak. The good functioning of the method is however perturbed by uncertainty about the wave celebrity in the sodium about wave propagation in waves guides that are mounted with the sensors and in the structure of the loop. (author). 1 ref., 8 figs

  20. Development of the SPIKE code for analysis of the sodium-water reaction

    Hwang, Sung Tai; Park, Jin Ho; Choi, Jong Hyeun; Kim, Tae Joon [Korea Atomic Energy Research Institute, Taejon (Korea)

    1998-08-01

    In the secondary loop of liquid metal reactors, including SG, water leak into sodium causes the sudden increase of pressure by the H{sub 2} and heat generated from reaction. At few miliseconds after leak, a sharp and short-lived increase of pressure is generated and its propagation depends on the acoustic constraint characteristics of secondary loop. As increasing leak amount of water, another pressure increase is caused by H{sub 2} and its transients depends on the resistance of pressure opening system, such as rupture disc. For prediction of the transients of initial spike pressure, a code of SPIKE was developed. The code was based on the following simplifications and assumptions: combination of total and half release of H{sub 2} rate, spherical shape of H{sub 2} bubble, compressible and Newtonian fluid for sodium. The program was built in FOTRAN language and consisted of 5 modules. Several sample calculations were performed to test the code and to determine the scale down factor of experimental facilities for experimental verification of the code: parameter study of the variables in chemical reaction model, comparison study with results calculated by superposition methods for simple piping structures, comparison study with results calculated by previous researchers, and calculation for KALIMER models of various size. With these calculation results, the generally predicted phenomena of sodium water reaction can be explained and the calculated ones by SPIKE code were well agreed with the previous study. And the scale down factor can be determined. (author). 88 refs., 99 figs., 39 tabs.

  1. Improvement and test calculation on basic code or sodium-water reaction jet

    Saito, Yoshinori; Itooka, Satoshi [Advanced Reactor Engineering Center, Hitachi Works, Hitachi Ltd., Hitachi, Ibaraki (Japan); Okabe, Ayao; Fujimata, Kazuhiro; Sakurai, Tomoo [Consulting Engineering Dept., Hitachi Engineering Co., Ltd., Hitachi, Ibaraki (Japan)

    1999-03-01

    In selecting the reasonable DBL (design basis water leak rate) on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on the basic code for sodium-water reaction (SWR) jet was performed for an actual scale SG. The improvement points of the code are as follows; (1) introduction of advanced model such as heat transfer between the jet and structure (tube array), cooling effect of the structure, heat transfer between analytic cells, and (2) model improvement for heat transfer between two-phase flow and porous-media. The test calculation using the improved code (LEAP-JET ver.1.30) were carried out with conditions of the SWAT-3{center_dot}Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results is reasonable and Influence to analysis result of a model. Code integration with the blow down analytic code (LEAP-BLOW) was also studied. It is suitable that LEAP-JET was improved as one of the LEAP-BLOW's models, and it was integrated into this. In addition to above, the improvement for setting of boundary condition and the development of the interface program to transfer the analytical results of LEAP-BLOW have been performed in order to consider the cooling effect of coolant in the tube simply. However, verification of the code by new SWAT-1 and SWAT-3 test data planned in future is necessary because LEAP-JET is under development. And furthermore advancement needs to be planned. (author)

  2. Improvement and test calculation on basic code or sodium-water reaction jet

    Saito, Yoshinori; Itooka, Satoshi; Okabe, Ayao; Fujimata, Kazuhiro; Sakurai, Tomoo

    1999-03-01

    In selecting the reasonable DBL (design basis water leak rate) on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on the basic code for sodium-water reaction (SWR) jet was performed for an actual scale SG. The improvement points of the code are as follows; (1) introduction of advanced model such as heat transfer between the jet and structure (tube array), cooling effect of the structure, heat transfer between analytic cells, and (2) model improvement for heat transfer between two-phase flow and porous-media. The test calculation using the improved code (LEAP-JET ver.1.30) were carried out with conditions of the SWAT-3·Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results is reasonable and Influence to analysis result of a model. Code integration with the blow down analytic code (LEAP-BLOW) was also studied. It is suitable that LEAP-JET was improved as one of the LEAP-BLOW's models, and it was integrated into this. In addition to above, the improvement for setting of boundary condition and the development of the interface program to transfer the analytical results of LEAP-BLOW have been performed in order to consider the cooling effect of coolant in the tube simply. However, verification of the code by new SWAT-1 and SWAT-3 test data planned in future is necessary because LEAP-JET is under development. And furthermore advancement needs to be planned. (author)

  3. Liquid metal fast breeder reactor steam generator survey of the consequences of large scale sodium water reaction

    Vambenepe, G.

    1978-01-01

    The ''Retona'' three-dimensional hydrodynamic computing code is being developed by Electricity de France to survey the consequences, on the very plant, of a large scale sodium water reaction in liquid metal steam generators. In this communication, the heat-exchanger geometry is schematized and the problem solving process briefly described under assumed simplifying hypotheses. The application of the results to the Creusot-Loire steam generator selected for Super-Phenix are given as an example. (author)

  4. An Evaluation of the Acoustic Signal processing Techniques for Sodium-Water Reaction Detection in KALIMER-600

    Hur, Seop; Seong, S. H.; Kim, T. J.; Kim, S. O.; Lee, M. K.

    2005-02-01

    KALIMER-600 is a pool type fast breeder reactor using liquid sodium as a coolant. Although it has the several advantages such as long-term fuel cycle and enhanced safety concepts, it is possible to leak the secondary side water/steam into sodium boundary. This event could make the plant abnormal condition. One of the major design issues in KALIMER-600 is, therefore, to develop the system which can early detect the sodium-water reaction to protect the sodium-water reaction event. After evaluating the various signal processing techniques for passive acoustic leak detection, we have proposed the early leak detection logics. the signal processing techniques for evaluation were the spectral estimation using the linear modeling, the estimation error of linear modeling, the system adaptation rate using an adaptive signal processing, and the background noise cancellation using adaptive and fixed filtering. As the analysis results regarding the stationary and the cross-correlation of leak signals and background noises, the two signal systems met a wide-dense stationary process and there was only the week cross correlation relationship between two signals. It is ,therefore, possible to use the linear/harmonic modeling of signal systems, and the leak signal in sensor outputs can be discriminated. As the results of the evaluation of the various spectral estimation methods, the spectral estimation method based on autoregressive modeling was more practical comparing with other methods in the sodium-water reaction detection. The passive acoustic leak detection logics were suggested based on above evaluations. the logics consist of 3 levels; transient identification, leak determination and leak symptom identification. The simulation results using sodium-water reaction signals showed that it was possible to determine the leak at above -3dB of SNR, while between -3 dB and -10 dB of SNR the logics determined the leak symptom identification. The detection sensitivity can be enhanced

  5. Experimental study of the attenuation waves oriented to transients caused by the sodium-water explosive reaction in fast reactors

    Pedroso, L.J.

    1990-01-01

    One of the problems related to fluid-structure interaction that can compromise the structural integrity of components of a fast reactor is the explosion caused by the sodium-water reaction, in the case of a flood at the level of the thermic exchange wall at the steam generator. In this paper we have considered the aspects of the pressure-waves damping caused by the reaction, when these waves transverse certain perforated structures. In order to solve this problem, we also adopted a parametric experimental approach, using a scale model (RIO test rig). (author)

  6. Simulation experiments for a large leak sodium-water reaction analysis. Volume 4. IHTS/relief system simulation tests

    Ploeger, D.W.

    1978-09-01

    Tests were performed in which a simplified 1/8-scale model of the intermediate heat transfer system and relief system of a LMFBR was subjected to a simulated sodium-water reaction in a steam generator. Pressures in the intermediate heat exchanger (IHX) and in the pipe were measured. The flow of water through the relief system was photographed and its velocity was measured. The forces on the relief system elbows resulting from the fluid flow were also measured. The tests were performed primarily to validate pulse propagation codes used for design and for direct use as design data

  7. Plan for support of large-plant (post-CRBR) needs in large-leak sodium-water reaction area

    Whipple, J.C.

    1980-03-01

    Work in the large leak test and analysis area of steam generator development has been carried out at GE-ARSD under 189a SG037 since 1973. The currently planned master schedule for the SG037 program is shown. Principal activities are the large leak testing program being carried out at the Large Leak Test Rig and the analysis methods development. The plan for supporting the large plant (post-CRBR) needs in the large leak sodium-water reaction area is outlined. Most of the needs will be answered in the current SG037 large leak program

  8. An experimental study on impingement wastage of Mod 9Cr 1Mo steel due to sodium water reaction

    Kishore, S., E-mail: skishore@igcar.gov.in [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Ashok Kumar, A.; Chandramouli, S.; Nashine, B.K.; Rajan, K.K.; Kalyanasundaram, P.; Chetal, S.C. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer Sodium heated steam generators are crucial components of fast breeder reactors. Black-Right-Pointing-Pointer A leak in steam generator tube will cause sodium water reaction that damages the tubes. Black-Right-Pointing-Pointer Experimental study was conducted to quantify the extent of damage on Mod 9Cr 1Mo tube due to a water leak. - Abstract: Sodium heated steam generator (SG) is a crucial component in the heat transport system of a fast breeder reactor (FBR). In case, one of its water/steam carrying tubes becomes defective, water/steam leaks into sodium, flowing in the shell side, causing sodium-water reaction, which is highly exothermic and producing corrosive NaOH. The reaction jet originating from a leaking tube may impinge on its adjacent tube, resulting in damage of the tube. Impingement wastage refers to this kind of damage, occurring to a tube of sodium heated SG, owing to a small water/steam leak from a neighboring tube. Extensive research works have been conducted all over the world to study various aspects of this phenomenon. Experimental studies were carried out in Indira Gandhi Centre for Atomic Research (IGCAR) to understand the effect of impingement wastage on Mod 9Cr 1Mo, which is the tube material of prototype fast breeder reactor (PFBR) SG. This paper brings out the data and experience gained through the experiments.

  9. Computational methodology of sodium-water reaction phenomenon in steam generator of sodium-cooled fast reactor

    Takata, Takashi; Yamaguchi, Akira; Uchibori, Akihiro; Ohshima, Hiroyuki

    2009-01-01

    A new computational methodology of sodium-water reaction (SWR), which occurs in a steam generator of a liquid-sodium-cooled fast reactor when a heat transfer tube in the steam generator fails, has been developed considering multidimensional and multiphysics thermal hydraulics. Two kinds of reaction models are proposed in accordance with a phase of sodium as a reactant. One is the surface reaction model in which water vapor reacts directly with liquid sodium at the interface between the liquid sodium and the water vapor. The reaction heat will lead to a vigorous evaporation of liquid sodium, resulting in a reaction of gas-phase sodium. This is designated as the gas-phase reaction model. These two models are coupled with a multidimensional, multicomponent gas, and multiphase thermal hydraulics simulation method with compressibility (named the 'SERAPHIM' code). Using the present methodology, a numerical investigation of the SWR under a pin-bundle configuration (a benchmark analysis of the SWAT-1R experiment) has been carried out. As a result, the maximum gas temperature of approximately 1,300degC is predicted stably, which lies within the range of previous experimental observations. It is also demonstrated that the maximum temperature of the mass weighted average in the analysis agrees reasonably well with the experimental result measured by thermocouples. The present methodology will be promising to establish a theoretical and mechanical modeling of secondary failure propagation of heat transfer tubes due to such as an overheating rupture and a wastage. (author)

  10. Experimental results of the consequences of sodium water reactions at the bottom tube plate region of straight tube steam generators

    Ruloff, G.

    1990-01-01

    Experience with sodium water reactions has shown, that the course of such a steam generator accident depends strongly on its place in the steam generator. For the EFR steam generators we have to differentiate between: weld region at the upper tube plate (gas space); bundle region; weld region at the bottom tube plate. This paper describes results of a running tests program simulating the bottom tube plate area. One main part of these tests is the investigation of the influence of wastage protection shrouds between the tubes in the weld region to avoid a fast leak propagation and to give time for leak detection and mastering of the accidents. (author). 10 figs, 2 tabs

  11. The UK contribution to the sodium-water reaction R and D programme in support of EFR

    Currie, R.; McCrindle, K.B.; Wright, P.J.

    1990-01-01

    The sodium-water reaction R and D programme for European Fast Reactor (EFR), is an integrated European project, as described in another paper at this Specialists Meeting. In this paper the UK contribution to this programme is described. The major sodium-water reaction test facility in the UK is the Super Noah Rig at Dounreay. This Rig is currently being modified to allow the following to be achieved during experiments: Provision of water/steam at the correct EFR Steam Generator Unit (SGU) flowrate, temperature and pressure in the 24 target tubes modelling the EFR SGU in the test section. Provision of sodium at the correct EFR SGU velocity, temperature and pressure through the test section modelling the EFR SGU during the experiments. Experiments in this facility to determine the leakrate at which overheating becomes important in various regions of the EFR SGU and to determine the damage caused by overheating will be the major UK contribution in the future. The modifications to the Rig and the future experimental programme are described. Several intermediate leak experiments have been carried out in the Super Noah Rig in the past, and the main results from them are summarized. These experiments have primarily been at PFR conditions but results have been obtained for 2.25 Cr 1Mo, 9 Cr 1 Mo and A800 steels, with and without internal water flow in the target tubes. During these previous experiments, the sodium was static and was at atmospheric pressure. Results from experiments carried out in the Small Water Leak Rig (SWLR) and the Small-Scale Test Facilities at Dounreay on microleak evolution, wastage of tubes and SGU walls, the behaviour of small leaks at the low temperature, bottom-tubeplate conditions and corrosion at sodium pool surfaces are presented. The future programme for these facilities is discussed. Fundamental experiments which have been carried out at Harwell on the behaviour of blocked microleaks are described. 2 refs, 15 figs, 1 tab

  12. Wastage Behavior of Modified 9Cr-1Mo Steel Tube Material by Sodium-Water Reaction (II)

    Jeong, Ji Young; Kim, Jong Man; Kim, Tae Joon; Choi, Jong Hyeun; Kim, Byung Ho; Lee, Yong Bum; Park, Nam Cook

    2010-01-01

    The Korea Advanced LIquid MEtal Reactor (KALIMER) steam generator is a helical coil, vertically oriented, shell-and-tube type heat exchanger with fixed tube-sheet. The conceptual design and outline drawing of the steam generator are shown. Flow is counter-current, with sodium on the shell side and water/steam on the tube side. Sodium flow enters the steam generator through the upper inlet nozzles and then flows down through the tube bundle. Feedwater enters the steam generator through the feedwater nozzles at the bottom of steam generator. Therefore, if there is a hole or a crack in a heat transfer tube, a leakage of water/steam into the sodium may occur, resulting in a sodium-water reaction. When such a leak occurs, so-called 'wastage' is the result which may cause damage to or a failure of the adjacent tubes. If a steam generator is operated for some time in this condition, it is possible that it might create an intermediate leak state which would then give rise to the problems of a multi-target wastage in a very short time. Therefore, it is very important to predict these phenomena quantitatively from the view of designing a steam generator and its leak detection systems. The objective of this study is a basic investigating of the sodium-water reaction phenomena by small water/steam leaks. For this, wastage tests for modified 9Cr-1Mo steel tube material were conducted, and an empirical formula of the wastage rate for this material was obtained from the results

  13. Outline of sodium-water reaction test in case of large leak with SWAT-3 testing equipments

    Sato, Minoru

    1978-01-01

    The key component in sodium-cooled fast reactors in steam generators, and the sodium-water reaction owing to the break of heating tubes may cause serious damages in equipments and pipings. The main factor controlling this phenomenon is the rate of leak of water. When the rate of water leak is small, the propagation of heating tube breaking may occur owing to ''wastage phenomenon'', on the other hand, when the rate of water leak is large, the phenomena of explosive pressure and flow occur due to the reaction heat and a large quantity of hydrogen generated by the reaction. In PNC, the testing equipments of SWAT-2 for small water leak and SWAT-1 for large leak were constructed, and the development test has been carried out to establish the method of safety design experimentally. The synthetic test equipment for the safety of steam generators, SWAT-3, was constructed to carry out the large water leak test in the scale close to actual plants. The object of the test, the outline of the test equipment, the phenomena of pressure and flow in the water injection test, the confirmation of the occurrence of secondary breaking of adjacent heating tubes, and the disposal of reaction products are described in this paper. This test is till going on, and the final conclusion will be reported later. (Kako, I.)

  14. High energy nuclear data evaluations for neutron-, proton-, and photon-induced reactions at KAERI

    Lee, Young Ouk; Chang, Jong Hwa; Kim, Doo Hwan; Lee, Jeong Yeon; Han, Yinlu; Sukhovitski, Efrem Sh.

    2001-01-01

    The Korea Atomic Energy Research Institute (KAERI) is building high energy neutron-, proton-, and photon-induced nuclear data libraries for energies up to hundreds MeV in response to nuclear data needs from various R and Ds and applications. The librares provide nuclear data needed for the accelerator-driven transmutation of nuclear waste and radiation transport simulations of cancer radiotherapy. The neutron library currently has 10 isotopes such as C-12, N-14, O-16, Al-27, Si-28, Ca-40, Fe-56, Ni-58, Zr-90, Sn-120, and Pb-208 for energies from 20 up to 400 MeV. The proton nuclear data were evaluated in a consistent manner with the neutron case, using the same nuclear model parameters. In addition to the same isotopes included in the neutron library, the proton library has 70 extra isotopes of 24 elements ranging from nitrogen to lead up to 150 MeV for which the evaluations are focused on the medical and activation analyses applications. The photonuclear data library has been built along with international collaboration by participating in the IAEA's Coordinated Research Project (CRP) which ended last year. Currently the KAERI photonuclear library includes 143 isotopes of 39 elements

  15. Dynamic loadings of sodium-water reactions in LMFBR and fusion power designs

    Chan, C. K.

    1977-07-01

    In liquid metal fast breeder reactor and lithium cooled fusion reactor, a sodium loop is being proposed to transfer heat from the primary coolant loop to the steam turbine cycle. Although by careful design and quality assurance programs, the probability for steam generator tube failure can be minimized, failure will still occur. The direct contact of sodium and water would cause a chemical reaction where hydrogen and sodium compounds are produced. This paper presents an evaluation of the potential hazards as a result of such a reaction. An analytical method is developed to investigate the extent of the reaction zone and the propagation of the pressure wave in the sodium system. In the calculation, the chemical reaction is assumed to be instantaneous, governed by the equation 2Na(l)+H/sub 2/O(l)..-->..Na/sub 2/O(l)+H/sub 2/(g)+31.4 K cal/gm. mole. Both the temperature and pressure rise in the reaction zone can be established from the energy balance and the equation of state for the gaseous product. As a consequence of the energy released, the chemical products suddenly expand with a high velocity. The expansion also generates a shock wave in both the water and the sodium systems. Results indicate that the reaction zone can expand in a rate of 1500 ft/sec and a shock wave with initial strength of 2300 atmospheres propagates with a speed of 8000 ft/sec into the sodium system. The propagating characteristics of the shock wave are obtained by solving the basic fluid equations. The shock wave decays rapidly, in the neighborhood of milliseconds, as soon as the reaction zone stops to expand. The decrease in the reaction zone pressure allows more water to react with the sodium and a second pulse is generated.

  16. Dynamic loadings of sodium-water reactions in LMFBR and fusion power designs

    Chan, C.K.

    1977-01-01

    In liquid metal fast breeder reactor and lithium cooled fusion reactor, a sodium loop is being proposed to transfer heat from the primary coolant loop to the steam turbine cycle. Although by careful design and quality assurance programs, the probability for steam generator tube failure can be minimized, failure will still occur. The direct contact of sodium and water would cause a chemical reaction where hydrogen and sodium compounds are produced. This paper presents an evaluation of the potential hazards as a result of such a reaction. An analytical method is developed to investigate the extent of the reaction zone and the propagation of the pressure wave in the sodium system. In the calculation, the chemical reaction is assumed to be instantaneous, governed by the equation 2Na(l)+H 2 O(l)→Na 2 O(l)+H 2 (g)+31.4 K cal/gm. mole. Both the temperature and pressure rise in the reaction zone can be established from the energy balance and the equation of state for the gaseous product. As a consequence of the energy released, the chemical products suddenly expand with a high velocity. The expansion also generates a shock wave in both the water and the sodium systems. Results indicate that the reaction zone can expand in a rate of 1500 ft/sec and a shock wave with initial strength of 2300 atmospheres propagates with a speed of 8000 ft/sec into the sodium system. The propagating characteristics of the shock wave are obtained by solving the basic fluid equations. The shock wave decays rapidly, in the neighborhood of milliseconds, as soon as the reaction zone stops to expand. The decrease in the reaction zone pressure allows more water to react with the sodium and a second pulse is generated

  17. Safety Evaluation for IHTS Integrity due to the Steam Generator Sodium-Water Reaction Event in the PGSFR

    Ahn, Sang-Jun; Lee, Kwi Lim; Ha, Kwi-Seok; Lee, Seung Won; Jeong, Taekyeong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    In this paper, the integrity of the IHTS and SG by the SWR event are evaluated using the SWAAMII code. A sodium has a chemical characteristics to rigorously react the water or steam and produce the high pressure waves and high temperature reaction heat. It has an excellent characteristics as a reactor coolant. But, there is an event to be considered in the sodium cooled fast reactor design. The Sodium-Water Reaction (SWR) event can be occurred by the water or steam leaks due to the break of the steam generator tubes. The propagated high pressure waves threathen the structural integrity of the affected Intermediate Heat Transport System (IHTS) and steam generator. If the IHTS pipes are failed, the sodium of the IHTS can be released to the containment building. To the peak pressure point of view, it is performed to evaluate the integrity of the major components due to the SWR event in the SG. The generated peak pressures due to the five SG tubes simultaneous break event are within the range of the design pressure for the SG, IHX and IHTS including the related pipes.

  18. Initial pressure spike and its propagation phenomena in sodium-water reaction tests for MONJU steam generators

    Sato, M.; Hiroi, H.; Tanaka, N.; Hori, M.

    1977-01-01

    With the objective of demonstrating the safe design of steam generators for prototype LMFBR MONJU against the postulated large-leak accident, a number of large-leak sodium-water reaction tests have been conducted using the SWAT-1 and SWAT-3 rigs. Investigation of the potential effects of pressure load on the system is one of the major concerns in these tests. This paper reports the behavior of initial pressure spike in the reaction vessel, its propagation phenomena to the simulated secondary cooling system, and the comparisons with the computer code for one-dimensional pressure wave propagation problems. Both rigs used are the scaled-down models of the helically coiled steam generators of MONJU. The SWAT-1 rig is a simplified model and consists of a reaction vessel (1/8 scale of MONJU evaporator with 0.4 m dia. and 2.5 m height) and a pressure relief system i.e., a pressure relief line and a reaction products tank. On the other hand, the SWAT-3 rig is a 1/2.5 scale of MONJU SG system and consists of an evaporator (reaction vessel with 1.3 m dia. and 6.35 m height), a superheater, an intermediate heat exchanger (IHX), a piping system simulating the secondary cooling circuit and a pressure relief system. The both water injection systems consist of a water injection line with a rupture disk installed in front of injection hole and an electrically heated water tank. Choice of water injection rates in the scaled-down models is made based on the method of iso-velocity modeling. Test results indicated that the characteristics of the initial pressure spike are dominated by those of initial water injection which are controlled by the conditions of water heater and the size of water injection hole, etc

  19. Wastage-resistant characteristics of 12Cr steel tube material. Small leak sodium-water reaction test

    Shimoyama, Kazuhito

    2004-03-01

    In the water leak accident of a steam generator designed for a sodium cooled reactor in the Feasibility Study, the localization of tube failure propagation by using an advanced water leak detector will be required from the viewpoints of the safety and economical efficiency of the plant. So far, the conventional knowledge and analytical tools have been used in the investigation and evaluation of water leak phenomenon; nevertheless, there was neither test data nor the study of quantitative evaluation on the corrosion behavior, so-called wastage-resistant characteristics, of 12Cr steel tube material in sodium-water reactions. Wastage tests for the 12Cr steel tube material were conducted in small water leaks by use of the Sodium-Water Reaction Test Rig (SWAT-1R), and the data of wastage rate were obtained in the parameter of water leak rate under the constant sodium temperature and distance between leak and target tubes. The test results lead to the following conclusions: (1) The wastage-resistibility of 12Cr steel is 1.6 times greater than that of 9Cr steel and is 2.7 times greater than that of 2.25Cr-1Mo steel. (2)The wastage-resistibility of 12Cr steel increases in smaller water leaks; especially in water leak rates of 1 g/sec or less, it is more excellent than that of SUS321 stainless steel used as Monju superheater tube material. (3) Based on the correlation of wastage rate for the 9Cr steel, the correlation for the 12Cr steel has been obtained to be used for the evaluation of tube failure propagation. As the correlation of wastage rate for the 12Cr steel is based on the correlation for the 9Cr steel, it gives enough conservatism in smaller water leaks. To serve in accurately evaluating the tube failure propagation in smaller water leaks, it is necessary to obtain new correlation of wastage rate for the 12Cr steel based on the data in the wide range of water leak rates. (author)

  20. Development of analysis model for mid and long-term effects of sodium water reaction event in LMR

    Eoh, Jae Hyuk; Sim, Yoon Sub; Kim, Seong O; Kim, Yeon Sik; Kim, Eui Kwang; Wi, Myung Hwan

    2002-04-01

    The Sodium-Water Reaction(SWR) is important in the design consideration of a LMR steam generator. To develop the analysis code for long-term effects of SWR, investigation on the characteristics of various SWR analysis code and the assessment of an analysis model for long term effects were performed. In an event of SWR, pressure spikes of wave propagation occur at its initial stage and last for a very short time, and then bulk motion of fluid and reaction products is progressed and lasts for a long time. In a case SWR occurs, a number of hydrogen bubbles produced and sodium is entrained into the bubbles through the gas-liquid bubble interfaces by evaporation or diffusion. The partial pressure of the sodium in a hydrogen bubble is determined as a function of the bubble size, temperature, and pressure, and is rapidly decreased as its size increased. From this, it can be considered that the bulk motion in the later phase of SWR is an axial motion caused by expansion of a single-phase hydrogen gas bubble produced by a reaction in the vicinity of the leak site. Through this investigation, a preliminary simple analysis model for long-term effects of SWR was set up and sensitivity study using the system design parameters such as pressure and temperature of IHTS for KALIMER was performed. Also, a simpler analysis model using the cover gas pressure change related to the production of a hydrogen bubble in a steam generator was developed from the analyses results. These simple analysis models of the reaction site and the pressure behavior with hydrogen production can be used to develop the mid and long-term analysis code for SWR in the KALIMER steam generator design

  1. Acoustic signal processing for the detection of sodium boiling or sodium-water reaction in LMFRs. Final report of a co-ordinated research programme 1990-1995

    1997-05-01

    This report is a summary of the work performed under a co-ordinated research programme entitled Acoustic Signal Processing for the Detection of Sodium Boiling or Sodium-Water Reaction in Liquid Metal Cooled Fast Reactors. The programme was organized by the IAEA and carried out from 1990 to 1995. It was the continuation of an earlier research co-ordination programme entitled Signal Processing Techniques for Sodium Boiling Noise Detection, which was carried out from 1984 to 1989. Refs, figs, tabs

  2. Sodium-water wastage and reactions program performed by general electric in support of the US. AEC LMFBR steam generator development

    Greene, D.A.

    1975-01-01

    This paper constitutes an interim report on the sodium-water reaction programs performed, using the GE-SOWAT, GE-SMALL LEAK BEHAVIOR RIG, and GE-PTTR facilities in support of LMFBR steam generator development and its application to the Clinch River Breeder Reactor Plant. Test data from these rigs are presented, including wastage data as a function of water injection rate, sodium temperature, and orifice geometry. Initial results for self-wastage of defects under prototypical conditions, and from proof-of-principle tests of a protected heat transfer tube concept are also presented. An analytical basis for wastage phenomena is suggested. (author)

  3. Sodium-water wastage and reactions program performed by general electric in support of the US. AEC LMFBR steam generator development

    Greene, D A

    1975-07-01

    This paper constitutes an interim report on the sodium-water reaction programs performed, using the GE-SOWAT, GE-SMALL LEAK BEHAVIOR RIG, and GE-PTTR facilities in support of LMFBR steam generator development and its application to the Clinch River Breeder Reactor Plant. Test data from these rigs are presented, including wastage data as a function of water injection rate, sodium temperature, and orifice geometry. Initial results for self-wastage of defects under prototypical conditions, and from proof-of-principle tests of a protected heat transfer tube concept are also presented. An analytical basis for wastage phenomena is suggested. (author)

  4. Contribution to the prediction of sodium-water reactions effects: application to confinement losses inside a steam generator building of a sodium fast reactor

    Daudin, Kevin

    2015-01-01

    Study of sodium-water reaction (SWR) consequences in open air represents a challenge in the frame of safety assessments of sodium fast reactors (SFR). In case of major accident and to predict consequences of SWR, it is necessary to better appreciate phenomena and especially quantity and rate of the energy release. The objective is thus to strengthen the understanding of such reactions in order to predict with lore accuracy its consequences on mechanical equipment in the surroundings. This work focuses on three areas : research of accidental sequences, experimental investigation, and phenomenological analysis before the explosive contact. At first, a tree structure risk analysis with calculations of dangerous phenomena permitted to suggest how the contact between reactants may happen. Then, demonstrative experimental studies were performed to deepen some practical aspects of the phenomenology, like the influence of the way the reactants get in contact. Data analysis conducted to the development of a phenomenological model, implemented into a software platform for numerical simulations. Although numerous hypothesis, transient heat transfer consideration enables to reproduce experimental observations, especially the influence of mixing conditions (sodium mass and initial temperatures) on the phenomenology. This study of the premixing step of sodium-water explosion is relevant in the frame of current prediction methods of mechanical loadings on structures. (author) [fr

  5. Analysis of the dynamic response of a double rupture disc assembly to simulated sodium-water reaction pressure pulses

    Leonard, J.R.

    1980-03-01

    A series of double rupture disc experiments were conducted in 1979 to evaluate the dynamic response characteristics of this pressure relief apparatus. The tests were performed in a facility with water simulating sodium and rising pressure pulses representative of the pressure increase resulting from a water/steam leak from a steam generator into sodium in the intermediate heat transport system of a breeder reactor power plant. Maximum source pressures ranged in magnitude from 50 psi to 800 psi. Dynamic response characteristics of each of the two rupture discs were similar to those observed in larger scale sodium-water experiments conducted in the Series I and Series II Large Leak Test Program at the Energy Technology Engineering Center. The SRI double rupture disc dynamic behavior was found to be consistent and amendable to modelling in the TRANSWRAP II computer code. A series of correlations which represent rupture disc buckling parameters were developed for use in the TRANSWRAP II code. The semi-empirical modeling of the rupture discs in the TRANSWRAP II code showed very good agreement with the experimental results

  6. Conclusions from the sodium-water reaction experiments performed with a straight tube bundle model for a steam generator with respect to the calculation method of the accident design pressure

    Ludwig, P.W.P.; Ruijterman, C.

    1975-01-01

    This paper will give some conclusions, drawn from the big-leakages sodium-water reaction experiments, on the calculation methods to be used in determining the sodium blow down, the water supply and the bubble pressure. The necessity of taking into account the compressibility of sodium is demonstrated. (author)

  7. Conclusions from the sodium-water reaction experiments performed with a straight tube bundle model for a steam generator with respect to the calculation method of the accident design pressure

    Ludwig, P W.P.; Ruijterman, C

    1975-07-01

    This paper will give some conclusions, drawn from the big-leakages sodium-water reaction experiments, on the calculation methods to be used in determining the sodium blow down, the water supply and the bubble pressure. The necessity of taking into account the compressibility of sodium is demonstrated. (author)

  8. Development of experimental method for self-wastage behavior in sodium-water reaction. Development of test rig (SWAT-2R) and study for experimental procedure

    Abe, Yuta; Shimoyama, Kazuhito; Kurihara, Akikazu

    2014-07-01

    In case of water leak from a penetrated crack on a tube of steam generator in the sodium cooled fast reactor (SFR), self-wastage, that increases the size of leak, may take place by corrosion related to chemical reaction between sodium and water. If the self-wastage continues in a certain period of time, the intact tube bundle may be damaged as a result of enlarged leak. For the safety evaluation of the accident, JAEA has been developing the analytical method of self-wastage using the multi-dimensional sodium-water reaction code. Experiments conducted so far used mainly crack-type test pieces. However, reproducibility was limited and it was difficult to evaluate individual effects of the phenomena in detail. This report describes the development of new experimental rig (SWAT-2R). SWAT-2R enables to examine corrosion effecting factors that were ambiguous in the previous studies. The report includes description of development of micro-leak test piece, examination of experimental procedure. The results will provide fundamental data for validation of the self-wastage analytical method. (author)

  9. Advancement of compressible multiphase flows and sodium-water reaction analysis program SERAPHIM. Validation of a numerical method for the simulation of highly underexpanded jets

    Uchibori, Akihiro; Ohshima, Hiroyuki; Watanabe, Akira

    2010-01-01

    SERAPHIM is a computer program for the simulation of the compressible multiphase flow involving the sodium-water chemical reaction under a tube failure accident in a steam generator of sodium cooled fast reactors. In this study, the numerical analysis of the highly underexpanded air jets into the air or into the water was performed as a part of validation of the SERAPHIM program. The multi-fluid model, the second-order TVD scheme and the HSMAC method considering a compressibility were used in this analysis. Combining these numerical methods makes it possible to calculate the multiphase flow including supersonic gaseous jets. In the case of the air jet into the air, the calculated pressure, the shape of the jet and the location of a Mach disk agreed with the existing experimental results. The effect of the difference scheme and the mesh resolution on the prediction accuracy was clarified through these analyses. The behavior of the air jet into the water was also reproduced successfully by the proposed numerical method. (author)

  10. KAERI photonuclear library

    Chang, Jong Hwa; Lee, Young Ouk; Han, Yin Iu

    2000-03-01

    This report contains summary information and figures depicting the KAERI photonuclear data library that extends up to 140 MeV of incident photon. The library consists of 143 isotopes from C-12 to Bi-209, providing the photoabsorption cross section and the emission spectra for neutron, proton, deuteron, triton, alpha particles, and all residual nuclides in ENDF6 format. The contents of this report and ENDF-6 format data library are available at http://atom.kaeri.re.kr/.

  11. Analysis of self-wastage phenomena of micro leak caused by sodium-water reaction in sodium-cooled fast breeder reactor through simulant experiment

    Jang, Sunghyon; Takata, Takashi; Yamaguchi, Akira

    2014-01-01

    Self-wastage phenomena are an enlargement of a leak on the heat transfer tube caused by a corrosive sodium-water reaction (SWR) in a steam generator (SG) of sodium-cooled fast breeder reactor (SFR). If the steam generator operates for sometimes under this condition, the self-wastage phenomena start from the sodium side and advance through the tube thickness. The leak rate stays almost constant level until the wastage reaches the sodium side, however, when the thin diaphragm of the tube wall is removed, the leak rate sharply increase, and it may bring a secondary failure of the surrounding heat transfer tubes. The design and safety concern is a possibility of the secondary failure of nearby SG tubes that could cause undesirable development of the accidents. One needs to evaluate the increased resultant leak rate due to the self-wastage phenomenon. Therefore, a quantification of the diameter of enlarged leak is needed to estimate the resultant leak rate. For this purpose, a simulant self-wastage experiment was proposed to investigate the self-enlargement of the leak so that evaluate the mechanism of the Self-wastage. In the experiment, high concentrated hydrochloric acid (HCl) is injected to the reaction tank that is filled sodium hydroxide (NaOH) solution through a nozzle made by paraffin wax. The self-enlargement of the leak was evaluated by considering the melted nozzle due to the reaction heat released from the Neutralization reaction. Also, a numerical investigation has been carried out to evaluate the enlarged nozzle and validate the results of experimental methodology. Based on the experimental and computational results, it is found that despite initial leak rate, there is an upper limit in the enlarged nozzle. These results show a similar tendency with the experimental result of SWAT-4 experiment carried out by Power Reactor and Nuclear Fuel Development Corporation (PNC), Japan. Furthermore, the increased resultant leak rate is evaluated using the enlarged

  12. Nuclear Data Center (NDC) of Korea Atomic Energy Research Institute (KAERI). Progress Report to the IAEA Technical Meeting of Nuclear Reaction Data Centers (NRDC)

    Lee, Young-Ouk

    2012-01-01

    Nuclear Data Center (NDC, former Nuclear Data Evaluation Lab.) of Korea Atomic Energy Research Institute (KAERI) has a director, 10 permanent staffs (2 in evaluation, 1 in measurement, 2 in atomic and molecular data, 2 in processing and validation, 3 in applications), one PhD student and one secretary. KAERI/NDC recently expanded its scope of work into the atomic and molecular data where two permanent staffs are involved. Mission of KAERI/NDC is disseminating outcomes of international network as well as promoting domestic nuclear data activities and related applications.

  13. Passive vibro-acoustic detection of a sodium-water reaction in a steam generator of a sodium-cooled fast neutrons nuclear reactor by beam forming

    Moriot, Jeremy

    2013-01-01

    This thesis deals with a new method to detect a sodium-water reaction in a steam generator of a fast sodium-cooled nuclear reactor. More precisely, the objective is to detect a micro-leak of water (flow ≤ 1 g/s) in less than 10 seconds by measuring the external shell vibrations of the component. The strong background noise in operation makes impossible the use of a detection system based on a threshold overrun. A beam forming method applied to vibrations measured by a linear array of accelerometers is developed in this thesis to increase the signal-to-noise ratio and to detect and locate the leak in the steam generator. A numerical study is first realized. Two models are developed in order to simulate the signals measured by the accelerometers of the array. The performances of the beam forming are then studied in function of several parameters, such as the source location and frequency, the damping factor, the background noise considered. The first model consists in an infinite plate in contact with a heavy fluid, excited by an acoustic monopole located in this fluid. Analyzing the transverse displacements in the wavenumber domain is useful to establish a criterion to sample correctly the vibration field of the plate. A second model, more representative of the system is also proposed. In this model, an elastic infinite cylindrical shell, filled with a heavy fluid is considered. The finite dimensions in the radial and circumferential directions lead to a modal behavior of the system which impacts the beam forming. Finally, the method is tested on an experimental mock-up which consists in a cylindrical pipe made in stainless steel and filled with water connected to hydraulic circuit. The water flow speed can be controlled by varying the speed of the pump. The acoustic source is generated by a hydro-phone. The performances of the beam forming are studied for different water flow speeds and different amplitude and frequencies of the source. (author) [fr

  14. Safeguards Implementation at KAERI

    Jung, Juang; Lee, Sung Ho; Lee, Byung-Doo; Kim, Hyun-Sook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    The main objective of the safeguards implementation activities is to assure that there are no diversions of declared nuclear material and/or no undeclared activity. The purpose of safeguards implementation activities is the assistance facility operators to meet the safeguards criteria set forth by the Atomic Energy Safety Acts and Regulations. In addition, the nuclear material and technology control team has acted as a contact point for domestic and international safeguards inspection activities and for the relevant safeguards cooperation. Domestic inspections were successfully carried out at the KAERI nuclear facilities pursuant to the domestic laws and regulations in parallel with the IAEA safeguards inspections. It is expected that safeguards work will be increased due to the pyro-related facilities such as PRIDE, ACPF and DUPIC, for which the IAEA is making an effort to establish safeguards approach. KAERI will actively cope with the plan of the NSSC by changing its domestic inspection regulations on the accounting and control of nuclear materials.

  15. Evaluation of a sodium-water reaction event caused by steam generator tubes break in the prototype generation IV sodium-cooled fast reactor

    Ahn, Sang June; Ha, Kwi Seok; Chang, Won Pyo; Kang, Seok Hun; Lee, Kwi Lim; Choi, Chi Woong; Lee, Seung Won; Yoo, Jin; Jeong, Jae Ho; Jeong, Tae Kyeong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-08-15

    The prototype generation IV sodium-cooled fast reactor (PGSFR) has been developed by the Korea Atomic Energy Research Institute. This reactor uses sodium as a reactor coolant to transfer the core heat energy to the turbine. Sodium has chemical characteristics that allow it to violently react with materials such as a water or steam. When a sodium–water reaction (SWR) occurs due to leakage or breakage of steam generator tubes, high-pressure waves and corrosive reaction products are produced, which threaten the structural integrity of the components of the intermediate heat-transfer system (IHTS) and the safety of the primary heat-transfer system (PHTS). In the PGSFR, SWR events are included in the design-basis event. This event should be analyzed from the viewpoint of the integrities of the IHTS and fuel rods. To evaluate the integrity of the IHTS based on the consequences of the SWR, the behaviors of the generated high-pressure waves are analyzed at the major positions of a failed IHTS loop using a sodium–water advanced analysis method-II code. The integrity of the fuel rods must be consistently maintained below the safety acceptance criteria to avoid the consequences of the SWR. The integrity of the PHTS is evaluated using the multidimensional analysis of reactor safety-liquid metal reactor code to model the whole plant.

  16. Thermomechanical Model and Bursting Tests to Evaluate the Risk of Swelling and Bursting of Modified 9Cr-1Mo Steel Steam Generator Tubes during a Sodium-Water Reaction Accident

    C. Bertrand

    2014-01-01

    Full Text Available The MECTUB code was developed to evaluate the risk of swelling and bursting of Steam Generator (SG tubes. This code deals with the physic of intermediate steam-water leaks into sodium which induce a Sodium-Water Reaction (SWR. It is based on a one-dimensional calculation to describe the thermomechanical behavior of tubes under a high internal pressure and a fast external overheating. The mechanical model of MECTUB is strongly correlated with the kind of the material of the SG tubes. It has been developed and validated by using experiments performed on the alloy 800. A change to tubes made of Modified 9Cr-1Mo steel requires more knowledge of Modified 9Cr-1Mo steel behavior which influences the bursting time at high temperatures (up to 1200°C. Studies have been initiated to adapt the mechanical model and to qualify it for this material. The first part of this paper focuses on the mechanical law modelling (elasticity, plasticity, and creep for Modified 9Cr-1Mo steel and on overheating thermal data. In a second part, the results of bursting tests performed on Modified 9Cr-1Mo tubes in the SQUAT facility of CEA are used to validate the mechanical model of MECTUB for the Modified 9Cr-1Mo material.

  17. Cooperation on impingement wastage experiment of Mod. 9Cr-1Mo steel using SWAT-1R sodium-water reaction test facility

    Beauchamp, F.; Allou, A.; Nishimura, M.; Umeda, R.

    2013-01-01

    Conclusion: • 6 experiments were carried out in the SWAT-1R facility of JAEA Oarai R&D Center to study the wastage resistance of the Mod. 9Cr-1Mo steel (T91) straight tubes. • These experiments were performed under the cooperation between CEA and JAEA. • The experiments were conducted successfully: - all the tubes were punctured by the reaction jet, - wastage and steam/water leak rates were obtained, - experimental results brought some new determining sets of wastage data on T91. • This fruitful cooperation has contributed to: - expanding the wastage database on T91, - upgrading wastage rates prediction from modelling, - the safety demonstration of future steam generators units

  18. Pyroprocessing technology development at KAERI

    Lee, Han Soo; Park, Geun Il; Kang, Kweon Ho; Hur, Jin Mok; Kim, Jeong Guk; Ahn, Do Hee; Cho, Yung Zun; Kim, Eung Ho

    2011-01-01

    Pyroprocessing technology was developed in the beginning for metal fuel treatment in the US in the 1960s. The conventional aqueous process, such as PUREX, is not appropriate for treating metal fuel. Pyroprocessing technology has advantages over the aqueous process: less proliferation risk, treatment of spent fuel with relatively high heat and radioactivity, compact equipment, etc. The addition of an oxide reduction process to the pyroprocessing metal fuel treatment enables handling of oxide spent fuel, which draws a potential option for the management of spent fuel from the PWR. In this context, KAERI has been developing pyroprocessing technology to handle the oxide spent fuel since the 1990s. This paper describes the current status of pyroprocessing technology development at KAERI from the head-end process to the waste treatment. A unit process with various scales has been tested to produce the design data associated with the scale up. A performance test of unit processes integration will be conducted at the PRIDE facility, which will be constructed by early 2012. The PRIDE facility incorporates the unit processes all together in a cell with an Ar environment. The purpose of PRIDE is to test the processes for unit process performance, operability by remote equipment, the integrity of the unit processes, process monitoring, Ar environment system operation, and safeguards related activities. The test of PRIDE will be promising for further pyroprocessing technology development

  19. Pyro processing technology at KAERI

    Lee, Hansoo; Kim, Eungho; Park, Seongwon

    2008-01-01

    KAERI has studied on the pyro processing as a spent fuel treatment method for more than decade. The process includes voloxidation, electroreduction, electrorefining with solid and liquid cathodes, and waste salt treatment. Each process has developed its own characteristics which are suitable for treating high mass flow. In the electroreduction process, a magnesia filter was used for integrated electrolytic reduction. More than 99% of reduction yield was achieved. Electrorefining process employs the continuous operation concept. Uranium deposits on the surface of graphite cathode and it is stripped off spontaneously to the bottom of the reactor, which allows continuous operation. Crystallization method was used for treating waste salt. Pure salt is recovered by Czochralski method or zone freezing method and subsequently recycled to the reactor. These advanced technologies ensure the operation of pyro processing in a larger scale

  20. Some problems of leaks in sodium-water steam generator

    Kozlov, F.A.; Sergeev, G.V.; Sednev, A.R.; Makarov, V.M.

    1976-01-01

    The paper contains data on wastage of steam generator structural materials and high-nickel alloys in the zone of water leakage into sodium as well as investigation results for self-enlargement of water leaks into sodium through defects in these materials. It is shown that the rate of material damage in the zone of sodium-water reaction and in the channel with water leaking-out decreases with increasing nickel content in steels and strongly depends on sodium temperature. The paper presents experimentally obtained dependences of leakage self-enlargement rates on sodium temperature and leakage size

  1. Current Status of Pyroprocessing Development at KAERI

    Hansoo Lee

    2013-01-01

    Full Text Available Pyroprocessing technology has been actively developed at Korea Atomic Energy Research Institute (KAERI to meet the necessity of addressing spent fuel management issue. This technology has advantages over aqueous process such as less proliferation risk, treatment of spent fuel with relatively high heat and radioactivity, and compact equipments. This paper describes the pyroprocessing technology development at KAERI from head-end process to waste treatment. The unit process with various scales has been tested to produce the design data associated with scale-up. Pyroprocess integrated inactive demonstration facility (PRIDE was constructed at KAERI and it began test operation in 2012. The purpose of PRIDE is to test the process regarding unit process performance, remote operation of equipments, integration of unit processes, scale-up of process, process monitoring, argon environment system operation, and safeguards-related activities. The test of PRIDE will be promising for further pyroprocessing technology development.

  2. A study for the KAERI research tunnel

    Kim, J.; Hwang, Y. S.; Park, H. S.; Park, S. K.; Park, B. Y.; Bang, K. S.; Kuh, J. H.; Kang, K. H

    1997-12-01

    Major goal of the R and D on the KAERI Research Tunnel in 1997 are 1) concept development of the KAERI research tunnel and its major units 2) computer simulation of facilities 3) study on thermo-hydro mechanical coupling in the vicinity of a waste repository 4) effect of excavated distrubed zone. In addition supplementary site investigation to understand the distribution of stresses in the site was done along with long term monitoring of the water table. (author). 44 refs., 16 tabs., 36 figs

  3. Reviews on the efficient nuclear material accountability at KAERI

    Kim, Hyun Sook; Ko, Han Suk; Lee, Seung Ho; Park, Ho Joon; Lee, Byung Doo

    2011-01-01

    KAERI(Korea Atomic Energy Research Institute) is constantly trying to efficiently implement safeguards in order to ensure international transparency and the credibility of KAERI safeguards. In its continuing efforts to implement safeguards efficiently, KAERI has developed KASIS(KAERI Safeguards Information Treatment System) and has linked KASIS with the RF ID system and HANARO fuel fabrication facility system. This paper describes the status of enhanced nuclear material accountancy through the development of KASIS at KAERI. The plans to more effectively implement nuclear material accountancy at KAERI are also reviewed

  4. The technological innovation case of the KAERI

    Choi, J. I.; Jang, S. K.; Hong, K. P.; Lee, E. S.

    2008-01-01

    The research aims to investigate what key success factors (KSFs) of technological innovation in KAERI are, and to suggest how these findings are utilized for KAERI. In order to achieve these goals we have employed case study based on in-depth interview and literature review. And there are two fields of research in KAERI: one is nuclear energy-related research, the other is non energy-related research. The former is 'nuclear fuel cladding tube' which is an industrial product and being regarded as catch-up (or imitative) mode of technological innovation: the latter is 'HemoHIM', herbal composition of health functional food, which is consumer goods and regarded as creative (or innovative) mode of technological innovation. We found some KSFs in these two research and development cases in KAERI: firstly, to train researcher to be a 'product champion' who can fill in the gap of 'death valley' between pure research and commercialization: secondly, to build researchers' competency in order to catch up advanced countries' technological competencies. Thirdly, to amend institutional rules and regulations for commercializing processes of R and D outcomes, notably 'R and D joint venture by Government Research Institute (GRI) and private sector' fourthly, to enhance the capabilities of external management for researchers' technological innovation competency. And finally, we recommend using successful R and D cases as educational materials when training young researchers for sharing old generations' experiences and tacit knowledge

  5. The DUPIC fuel development program in KAERI

    Yang, M S; Park, H S [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-07-01

    This study describes the DUPIC fuel development program in KAERI as follows; Burning spent PWR fuel again in CANDU by DUPIC, Compatibility with existing CANDU system, Feasibility of DUPIC fuel fabrication, Waste reduction, Safeguard ability, Economics of DUPIC fuel cycle, The DUPIC fuel development program, and International prospective. 5 refs., 10 figs.

  6. Advanced Electrorefining Process at KAERI

    Hansoo Lee; Jong Hyun Lee; Sung Bin Park; Yoon Sang Lee; Eung Ho Kim; Sung Won Park

    2008-01-01

    In order to enhance the throughput of a pyro-processing in which electrochemical processes are mostly engaged, the design of a continuous concept is required. The graphite cathode in the electro-refiner enables the uranium deposit on the cathodes to be stripped off spontaneously, resulting in a continuous reaction. The collected uranium deposits at the bottom of the inner cone of the reactor are transferred by a conveyor. The residuals in the anode basket after the uranium is depleted are noble metals. These are also collected at the bottom of the outer shell of the reactor, and conveyed from the reactor for a further treatment. This work addresses the design of the electro-refiner for a continuous operation. The behavior of particles such as uranium dendrites or noble metals was analyzed to achieve the proper operating conditions. The operating conditions for the cathode processor in which molten salt is distilled were also investigated. (authors)

  7. The technological innovation case of the KAERI

    Choi, J. I. [Habat Univ., Daejeon (Korea, Republic of); Jang, S. K. [Sungkonghoe Univ., Seoul (Korea, Republic of); Hong, K. P. [Baekseok Univ., Chunan (Korea, Republic of); Lee, E. S. [National Fusion Research Institue, Daejeon (Korea, Republic of)

    2008-01-15

    The research aims to investigate what key success factors (KSFs) of technological innovation in KAERI are, and to suggest how these findings are utilized for KAERI. In order to achieve these goals we have employed case study based on in-depth interview and literature review. And there are two fields of research in KAERI: one is nuclear energy-related research, the other is non energy-related research. The former is 'nuclear fuel cladding tube' which is an industrial product and being regarded as catch-up (or imitative) mode of technological innovation: the latter is 'HemoHIM', herbal composition of health functional food, which is consumer goods and regarded as creative (or innovative) mode of technological innovation. We found some KSFs in these two research and development cases in KAERI: firstly, to train researcher to be a 'product champion' who can fill in the gap of 'death valley' between pure research and commercialization: secondly, to build researchers' competency in order to catch up advanced countries' technological competencies. Thirdly, to amend institutional rules and regulations for commercializing processes of R and D outcomes, notably 'R and D joint venture by Government Research Institute (GRI) and private sector' fourthly, to enhance the capabilities of external management for researchers' technological innovation competency. And finally, we recommend using successful R and D cases as educational materials when training young researchers for sharing old generations' experiences and tacit knowledge.

  8. Overview of the Radioecological Research at KAERI

    Choi, Yong Ho; Lim, Kang Muk; Kim, Byung Ho; Keum, Dong Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    This paper presents a brief history of the research and a summary of the data production. During the past 30 years, a comparatively large amount of radioecological data for food crops was produced at KAERI. Some of the data have been used for the off-site dose calculation or dynamic food-chain model validation in one way or another. A considerable amount of KAERI data was included in an IAEA's handbook and underlying TECDOC. Further studies should be conducted to have sufficient numbers of parameter values to realistically cover various environmental and agricultural conditions. It is desirable for as many of the produced data as possible to be used by the dose assessor. Not only the data producer but also the dose assessor needs to make an effort for a greater amount of the domestic data to be used in estimating the public dose for Koreans. Radioecology is a scientific discipline for studying the movement and accumulation of radionuclides within ecosystems composed of air, soil, water and living organisms including humans. It started in the late 1940s in the USSR and the early 1950s in the USA for the purpose of assessing the environmental impact of the radionuclides released by military uses of fissile material. With an increase in the peaceful use of nuclear energy, radioecologists took a great interest in the environmental impact assessment of nuclear power plants and other nuclear fuel cycle facilities. Radiation doses to the public by the planned and ongoing operations of such nuclear installations should be estimated for both normal operation and an accident. These estimations are made using assessment models which require parameter values to quantify various transfer processes of radionuclides in the ecosystem. In KAERI, radioecological research has been conducted for the past 30 years with an emphasis put on the production of data on the transfer of radionuclides to major food crops.

  9. Overview of the Radioecological Research at KAERI

    Choi, Yong Ho; Lim, Kang Muk; Kim, Byung Ho; Keum, Dong Kwon

    2013-01-01

    This paper presents a brief history of the research and a summary of the data production. During the past 30 years, a comparatively large amount of radioecological data for food crops was produced at KAERI. Some of the data have been used for the off-site dose calculation or dynamic food-chain model validation in one way or another. A considerable amount of KAERI data was included in an IAEA's handbook and underlying TECDOC. Further studies should be conducted to have sufficient numbers of parameter values to realistically cover various environmental and agricultural conditions. It is desirable for as many of the produced data as possible to be used by the dose assessor. Not only the data producer but also the dose assessor needs to make an effort for a greater amount of the domestic data to be used in estimating the public dose for Koreans. Radioecology is a scientific discipline for studying the movement and accumulation of radionuclides within ecosystems composed of air, soil, water and living organisms including humans. It started in the late 1940s in the USSR and the early 1950s in the USA for the purpose of assessing the environmental impact of the radionuclides released by military uses of fissile material. With an increase in the peaceful use of nuclear energy, radioecologists took a great interest in the environmental impact assessment of nuclear power plants and other nuclear fuel cycle facilities. Radiation doses to the public by the planned and ongoing operations of such nuclear installations should be estimated for both normal operation and an accident. These estimations are made using assessment models which require parameter values to quantify various transfer processes of radionuclides in the ecosystem. In KAERI, radioecological research has been conducted for the past 30 years with an emphasis put on the production of data on the transfer of radionuclides to major food crops

  10. MASTER- an indigenous nuclear design code of KAERI

    Cho, Byung Oh; Lee, Chang Ho; Park, Chan Oh; Lee, Chong Chul

    1996-01-01

    KAERI has recently developed the nuclear design code MASTER for the application to reactor physics analyses for pressurized water reactors. Its neutronics model solves the space-time dependent neutron diffusion equations with the advanced nodal methods. The major calculation categories of MASTER consist of microscopic depletion, steady-state and transient solution, xenon dynamics, adjoint solution and pin power and burnup reconstruction. The MASTER validation analyses, which are in progress aiming to submit the Uncertainty Topical Report to KINS in the first half of 1996, include global reactivity calculations and detailed pin-by-pin power distributions as well as in-core detector reaction rate calculations. The objective of this paper is to give an overall description of the CASMO/MASTER code system whose verification results are in details presented in the separate papers

  11. Study of the moderating effect of salts on the sodium-water reaction on the cleaning of irradiated fuel assemblies from fast neutron reactors, using fluid sodium heat transfer

    Lacroix, Marie

    2014-01-01

    Within the framework of the development of generation IV reactors one of the research tracks is related to the development of fast neutron reactors using fluid sodium heat transfer. The CEA (French Alternative Energies and Atomic Energy Commission) plans to build a prototype of reactor of this type called 'ASTRID'. To address development requirements for this prototype, research is in progress on the reactor's availability and in particular on the reduction of the washing duration for residual sodium fuel assemblies during their discharge. In fact, because sodium is very reactive with water (presently the only available process), the washing is done, for example, by very gradual addition. A solution currently being studied at the CEA and which is the subject of this thesis report consists of the addition of an aqueous salts solutions to the washing water in order to slow down the kinetic reaction. This doctoral dissertation describes the various salts, which have been evaluated and aims to explain their action mode. (author) [fr

  12. Overview of severe accident research at KAERI

    Kim, H.D.; Kim, S.B.; Hong, S.W.; Kim, D.H.

    2000-01-01

    The severe accident research program at Korea Atomic Energy Research Institute, within the framework of governmental 10 year long-term nuclear R and D program, aims at the development of assessment techniques and accident management strategies for the prevention and mitigation of potential risk. The research program includes experimental efforts, development of phenomena specific models and development of an integrated computer code. The results of research program is intended to be utilized for the design of the advanced light water reactor and development of accident management strategies for the operating reactors. The main focused areas of recent investigation at KAERI are experiments on in-vessel core debris retention (SONATA-IV) and fuel coolant interaction (TROI) along with the development of models and integrated computer code (MIDAS). (author)

  13. Over view of nuclear fuel cycle examination facility at KAERI

    Lee, Key-Soon; Kim, Eun-Ga; Joe, Kih-Soo; Kim, Kil-Jeong; Kim, Ki-Hong; Min, Duk-Ki [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-09-01

    Nuclear fuel cycle examination facilities at the Korea Atomic Energy Research Institute (KAERI) consist of two post-irradiation examination facilities (IMEF and PIEF), one chemistry research facility (CRF), one radiowaste treatment facility (RWTF) and one radioactive waste form examination facility (RWEF). This paper presents the outline of the nuclear fuel cycle examination facilities in KAERI. (author)

  14. A Study on the Revitalizing of technology commercialization in KAERI

    Choi, J. I.; Jang, S. K.; Hong, G. P.; Lee, E. S.

    2009-02-01

    The TEC training program should be implemented for researches who want to commercialize their own technologies. To build creative organization culture is essential for technology commercialization. Collaboration strategy is related to analyze how KAERI is catching up their technological capabilities in nuclear technology, and what the success factors of KAERI in technology commercialization are.

  15. Influence of sodium water reaction on MONJU steam generator

    Takahashi, T.; Ohmori, Y.; Hoshi, Y.

    1984-01-01

    Despite the strenuous efforts improving the reliability of steam generators, it is required to ascertain the safe shutdown at Design Basis Leak and also to take the necessary actions to minimize the plant damage for more realistic small leaks. The process of Monju DBL selection and its supporting R and D works are included in this paper, together with the evaluation of system and critical components in direct connection with DBL. The detail plant shutdown procedures (including auxiliary system sequential action) at the time of water leaks are also explained. (author)

  16. Review of activities concerning sodium water reaction in LMFBR

    Rajput, A.K.

    1984-01-01

    This paper presents a review of activities concerning safety engineering programme for steam generators of FBT reactor in India. Leak rate and its effect and leak detection system are briefly discussed

  17. Import/Export Control for ITT in KAERI

    Lee, Sung Ho; Kim, In Cheol; Kim, Hyun Jo; Kim, Hyun Sook; Kim, Mun Ja [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    The representatives of I/E (Import/Export) control in international society are NSG of nuclear fields, MTCR of missile fields, WA of conventional weapon fields and AG of bio-chemical fields. One of recent issues of the international I/E organizations is to strengthen ITT (Intangible Technology Transfer or Intangible Transfer of Technology). According to the ITT policy, ROK governments reinforced domestic I/E control for the non-proliferation of WMD through the Foreign Trade Law recently modified. There are international transfers of various kinds of items and technologies produced in KAERI as an integrated R and D institute in nuclear fields. In this study, KAERI is to develop a reasonable implementation methodology for the establishment of KAERI I/E control system to meet the requirements of the law. The main purpose of methodology development is to establish a frame of I/E control including ITT in KAERI. According to the methodology, KAERI held seminars twice for the public relations and education and prepared the regulation for I/E control. At present, KAERI is making a provision to check whether each R and D activity is related to the strategic item or technology. In the near future, KAERI will make efforts to get the CP license for effective implementation of I/E control of dual-use item/technology and follow up the changes of I/E control in nuclear field.

  18. Preliminary analysis of the KAERI RCCS Experiment Using GAMMA+

    Khoza, Samukelisiwe; Tak, Nam-il; Lim, Hong-Sik; Lee, Sung-Nam; Cho, Bong-Hyun; Kim, Jong-Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    This paper describes the analysis of the KAERI RCCS experiment. GAMMA+ code was used for analysis of the RCCS 1/4-scale natural cooling experimental facility designed and built at KAERI to verify the performance of the natural circulation phenomenon. The results obtained from the GAMMA+ analysis showing the temperature profiles and flow rates at steady state were compared with the results from the preliminary experiments conducted in this facility. GAMMA+ analysis for the KAERI RCCS experimental setup was carried out to understand its natural circulation behavior. The air flow rate at the chimney exit achieved by experiments was from to be almost same as that of GAMMA+.

  19. Study on Establishing Standard Administrative Report Guidelines for KAERI

    Koo, Hwang Duk; Cho, Woo Sung; Lee, Bong Jae

    2012-12-15

    Ο The main purpose of administrative report of an organization is to deliver a critical mind about surrounding circumstance and rational alternatives to a final decision maker Ο An established report system with unified formality and systematic concept playes critical role to make right decision and efficient review about pending issues Ο By understanding current situation of report system using in KAERI and analysing examples of other organization, we established specific administrative report writing guideline for KAERI Ο We expect efficient communication and increasing productivity from the guideline by establishing and diffusing administrative report common writing guideline reflecting longstanding administrative experience and know-how of a specialized committeeman of KAERI.

  20. Study on Establishing Standard Administrative Report Guidelines for KAERI

    Koo, Hwang Duk; Cho, Woo Sung; Lee, Bong Jae

    2012-12-01

    Ο The main purpose of administrative report of an organization is to deliver a critical mind about surrounding circumstance and rational alternatives to a final decision maker Ο An established report system with unified formality and systematic concept playes critical role to make right decision and efficient review about pending issues Ο By understanding current situation of report system using in KAERI and analysing examples of other organization, we established specific administrative report writing guideline for KAERI Ο We expect efficient communication and increasing productivity from the guideline by establishing and diffusing administrative report common writing guideline reflecting longstanding administrative experience and know-how of a specialized committeeman of KAERI

  1. Interaction of NRCs with their environment - KAERI's experience

    Chang, In Soon

    2001-01-01

    Main players in KAERI's environment are the Government, nuclear industry (essentially nuclear power related), Academic community and the public. The Board of Trustees of KAERI has members from three important ministries of the Government and this Board formulates the nuclear R and D programme. The current programme plan covers a period of 1996-2006. The Korean nuclear industry has grown out of the core groups within KAERI. Until 1996, certain key areas in the design of nuclear steam supply system, nuclear fuel and nuclear waste management were still a part of KAERI responsibilities. However, with the growth of the nuclear power programme to 14 GW(e) (16 reactors), and more reactors under construction and plan, a decision has been taken to shift these activities to the industry, along with the personnel (600). The Government has also decided to secure financial resources for R and D by a contribution of 0.1 cents/kw·h from the nuclear utilities to a fund. In 1998 this fund collected 90 million US$ and 75% was made available to KAERI. So there is a very strong linkage between the Government, KAERI and the nuclear industry. With the academic community, KAERI takes post-graduate and post doctoral research students, gives R and D projects to the universities and has joint projects in some areas like fusion research. With public, KAERI has followed the policy of openness. It has made specific efforts to convey more easily understood benefits of radioisotopes and radiation. Also, communication is quite often targeted at specific groups rather than public at large. This policy has helped in the public acceptance of nuclear power which provided 41% of the electricity in 1998. (author)

  2. Recent and future PIE activities in KAERI

    Ahn, Sangbok; Ryu, Woo-seok; Hong, Kwonpyo; Jeon, Yongbum; Kim, Dosik; Choo, Yongsun

    2012-01-01

    KAERI has two PIE hot cell facilities. One is Irradiated Material Examination Facility (IMEF) to examine irradiated nuclear fuels and core structural materials at HANARO, and the other is a Post Irradiation Examination Facility (PIEF) to do the operated PWR nuclear fuels and skeleton. Their activities are categorized by hot cell examinations, new technique developments, maintenance of facility utilities and a public acceptance work. In the past three years hot cell tests were executed over 2,000 times related to R and D projects of the future and next generation reactors such as SMART, U-Mo fuels, I-NERI etc., including 30 rods to be operated in domestic PWR's. To supply PIE data on time to the user schedules new equipment and techniques are being developed for 10 items which include an annealing fission gas release rate, thermal diffusivity measurement, a laser puncturing fission gas collection system and mechanical property measurements on PWR FA skeleton etc. For maintenance of facilities the aged utility equipment are refurbished and exchanged for new ones. The partly cracked and leaking building walls are completely repaired, and the aged electric UPS's, HVAC system parts, heating and cooling system are exchanged for new ones. Additionally efforts to upgrade the public acceptance for facility visiting events, open training courses to the university and graduated students have been made. Regarding the future of domestic R and D and a power reactor operating plan the demand for hot cell examinations will be steadily increased. Along with them new PIE techniques on TRISO fuels, minor actinide SFR fuels and CANDU fuels etc are required to be developed. New space to install small scale hot cells, and develop for the extreme conditioned test to meet future demands will be taken. (author)

  3. Web-based sorption database (KAERI-SDB)

    Lee, Jae Kwang; Baik, Min Hoon

    2010-10-01

    Radionuclide sorption data is necessary for the safety assessment of radioactive waste disposal. However the accessibility to the nuclide sorption database is limited. The web-based sorption database (KAERI-SDB) was developed to provide sorption data in a convenient way. The development of the KAERI-SDB was achieved by improving the performance of pre-existing sorption DB programme (SDB-21C) and incorporating the user requirement. The KAERI-SDB was designed that users can access it by using a web browser. Main functions of the KAERI-SDB include (1) log-in/join, (2) search and store of sorption data and (3) scatter plot chart and index chart. It is expected that the KAERI-SDB is widely applied to the safety assessment of radioactive waste disposal by enhancing the accessibility to experts and practitioner related the nuclear industry and governmental administration. It is also expected that reliabilities for the radioactive waste disposal increased by opening the web-based sorption DB to public

  4. KAERI results for BN600 full MOX benchmark (Phase 4)

    Lee, Kibog Lee

    2003-01-01

    The purpose of this document is to report the results of KAERI's calculation for the Phase-4 of BN-600 full MOX fueled core benchmark analyses according to the RCM report of IAEA CRP Action on U pdated Codes and Methods to Reduce the Calculational Uncertainties of the LMFR Reactivity Effects. T he BN-600 full MOX core model is based on the specification in the document, F ull MOX Model (Phase4. doc ) . This document addresses the calculational methods employed in the benchmark analyses and benchmark results carried out by KAERI

  5. Implementation of the Nuclear Export Control at KAERI

    Kim, Hyun-Jo; Lee, Byung-Doo; Lee, Sung-Ho

    2006-01-01

    Korea has joined multilateral export control regimes which include Wassenaar Arrangement(WA), Nuclear Suppliers Group(NSG), Missile Technology Control Regime(MTCR) and Australian Group(AG), and their guideline and control lists are reflected in domestic legislation. Also, Catch-all control entered into force on 1 January 2003 in Korea. The frequency of the exports of product as a result of R and D and cooperation with other countries has been increased at Korea Atomic Energy Research Institute (KAERI). Therefore, this report describes the implementation status of a nuclear export control at KAERI and points out the practical issues

  6. Development of Operational Parameters for Advanced Voloxidation Process at KAERI

    Lee, Jae Won; Park, J. J.; Shin, J. M.; Yun, Y. W.; Park, G. I.; Lee, J. W.

    2010-10-01

    KAERI has been developing a voloxidation process as a head-end process of pyroprocessing technology with INL (Idaho National Laboratory). The work scope of KAERI is to develop the operation parameters for advanced voloxidation process at KAERI using surrogate materials and SIMFUEL. In order to evaluate operation conditions of an advanced voloxidation process, oxidation and vaporization behavior of metals and Cs compounds was investigated in terms of thermal treatment atmosphere and temperature by using thermodynamic data. And also, the oxidation and vaporization behavior of semi-volatile fission products with process pressure and temperature was investigated using surrogate materials. Particle size control for U 3 O 8 powder was investigated using SIMFUEL and a rotary voloxidizer. According to analysis of KAERI works, the operation conditions for advanced voloxiation process may be consisted of the following four steps: 1) oxidation of UO 2 pellet into U 3 O 8 powder at 500 .deg. C in oxidative atmosphere, 2) additional oxidation of noble metal alloy and vaporization of high vapor pressure of fission products at 700 .deg. C in oxidative atmosphere, 3) granulation of U 3 O 8 powder and vaporization of Cs compounds at 1200 .deg. C in an atmosphere of argon, and 4) reduction of UO 2+x granules into UO 2 granules at 1000 .deg. C in an atmosphere of 4%H 2 -Ar. This report will be used as a useful means for determining the operation parameters for advanced voloxidation process

  7. KAERI's challenge to steady production of radioisotopes and radiopharmaceuticals

    Park, J.H.; Han, H.S.; Park, K.B.

    2000-01-01

    The Korea Atomic Energy Research Institute (KAERI) is a national organization in Korea, and has been doing many research and development works in radioisotope production and applications for more than 30 years. Now KAERI regularly produces radioisotopes (I-131, Tc-99m, Ho-166) for medical use and Ir-192 for industrial use. Various I-131 labeled compounds and more than 10 kinds of Tc-99m cold kits are also produced. Our multi-purpose reactor, named HANARO, has been operative since April of 1995. HANAKO is an open tank type reactor with 30 MW thermal capacity. This reactor was designed not only for research on neutron utilization but for production of radioisotopes. KAERI intended to maximize the radioisotope production capability. For this purpose, radioisotope production facilities (RIPF) have been constructed adjacent to the HANARO reactor building. There are four banks of hot cells equipped with manipulators and some of the hot cells were installed according to the KGMP standards and with clean rooms. In reviewing our RI production plan intensively, emphasis was placed on the development of new radiopharmaceuticals, development of new radiation sources for industrial and therapeutic use, and steady production of selected radioisotopes and radiopharmaceuticals. The selected items are Ho-166 based pharmaceuticals, fission Mo-99/Tc-99m generators. solution and capsules of I-131, and Ir-192 and Co-60 for industrial use. The status and future plan of KAERI's research and development program will be introduced, and will highlight programs for steady production. (author)

  8. An approach to develop a PSA workstation in KAERI

    Kim, T. W.; Han, S. H.; Park, C. K.

    1995-01-01

    This paper describes three kinds of efforts for the development of PSA workstation in KAERI; Development of a PSA tool, KIRAP, Reliability Database Development, Living PSA tool development. Korea has 9 nuclear power plants (NPPs) in operation and 9 NPPs under design or construction. For the NPPs recently constructed or designed, the probabilistic safety assessments (PSAs) have been performed by the Government requirements. For these PSAs, the MSDOS version of KIRAP has been used. For the consistent data management and the easiness of information handling needed in PSA, APSA workstation, KIRAP-Win is under development under Windows environment. For the reliability database on component failure rate, human error rate, and common cause failure rate, data used in international PSA or reliability data handbook are collected and processed to use in Korean new plants' PSAs. Finally, an effort for the development of a living PSA tool in KAERI based on dynamic PSA concept is described

  9. Approach on origin management of nuclear materials at KAERI

    Kim, Hyun-Jo; Lee, Sung-Ho; Lee, Byung-Doo; Kim, In-Chul; Kim, Hyun-Sook; Jung, Juang

    2017-01-01

    This paper describes the current origin management approach and reviews the requirement to be reflected to meet the bilateral agreements. KAERI developed the origin management system to efficiently and effectively manage the origin information. The system is connected with KASIS to share the information on the inventory changes of nuclear material. After development of the system, however, the new concept of obligated nuclear material is introduced according to the amended ROK-US agreement. Also, the origin management system based on IAEA accounting reports needs to revise to include the nuclear material exempted from safeguards. Therefore KAERI will improve the origin management system to meet the requirement of bilateral agreements and NSSC notice to be revised.

  10. Status report of the KAERI/NDEL. P1

    Chang, Jonghwa

    2001-01-01

    KAERI/NDEL has successfully finished a 4 year national nuclear Research and Development project, Establishment of Nuclear Data System, and started a new 4 year project, Evaluation of Nuclear Data for Nuclear Research and development Projects. KAERI/NDEL is providing nuclear data on-line service targeting non-nuclear data experts. Three new facilities have been added for nuclear data measurement capability of Korea, namely, E-Linac based TOF; Tandem VDG based n-source; and Cyclotron based Vacuum chamber. Main directions of nuclear data development on next 4 years are the Fission Products data for Transmutation, the data for Thorium cycle, the Photon-production data for in-core detector, and the Intermediate energy data for ADS

  11. Sodium-water clusters and their role in radiation chemistry

    Dhar, S.; Kestner, N.R.

    1988-01-01

    Studies of sodium-water clusters are presented which could serve as models for the recently suggested intermediate species in the radiation chemistry of water. The ionization potentials and the lower excited states of sodium with n-water molecules are calculated by ab initio quantum chemistry methods. The ionization potential calculated at the SCF level for the water monomer is 4.10 eV, which becomes 4.34 at the MP2 correlation level. The experimental value is 4.379 ± 0.002 eV. Structural data is presented for the lower members of the sodium with n-water clusters. In addition the Hartree-Fock calculations indicate that there should be some strong charge transfer to solvent transitions at higher energies. (author)

  12. The upgrade of nuclear material accounting system at KAERI

    Kim, Hyun Jo; Kim, Hyun Sook; Park, Ho Jun; Ko, Han Suk; Lee, Byung Doo

    2010-01-01

    The agreement between the government of Republic Of Korea (ROK) and the IAEA for the application of safeguards was signed and entered into force in 1975. The Additional Protocol (AP) to the Safeguards Agreement between the ROK and the IAEA was signed in 1999 and entered into force on 19 February 2004. Also, Implementation of Integrated Safeguards (IS) was started on 1 July, 2008 after a draw of the broader conclusion. The IAEA provides 2 hours notification for Random Interim Inspection (RII) under IS. For RII, the facility has to prepare the inspection documents in a short time. Therefore, KAERI (Korea Atomic Energy Research Institute) developed a new computerized nuclear material accounting system named KASIS (KAERI Safeguards Information treatment System) to treat the data by on-line for RII. For the efficient IS implementation, KAERI has a plan to upgrade the system to reflect the accounting approaches or reporting procedure according to facility characteristic. This paper describes the upgrade of the nuclear material accounting system and the efforts to reduce the burden of the facility operators

  13. Detailed analysis of the KAERI nTOF facility

    Kim, Jong Woon; Lee, Young Ouk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-06-15

    A project for building a neutron time-of-flight (nTOF) facility is progressing. We expect that the construction will start in early 2016. Before that, a detailed simulation based on the current architectural drawings was performed to optimize the performance of our facility. Currently, several parts had been modified or changed from the original design to reflect requirements such as the layout of the electron beam line, shape of the vacuum chamber producing a neutron beam, and the underground layout of the nTOF facility. Detailed analysis for these modifications has been done with MCNP simulation. An overview of our photo-neutron source and KAERI nTOF facility were introduced. The numerical simulations for heat deposition, source term, and radiation shielding of KAERI nTOF facility were performed and the results are discussed. We are expecting that the construction of the KAERI nTOF facility will start in early 2016, and these results will be used as basic data.

  14. A Study on the Export Control System at KAERI

    Kim, I. C.; Lee, B. D.; Kim, H. J.; Kim, H. S.; Jung, J. A.

    2015-01-01

    The current non-proliferation regime requires strengthening the export control from Korea to foreign countries. This means that the ministries related to export control deeply emphasize the prohibition of the illegal proliferation in the domestic society as well as international society. The principle of export control for non-proliferation of WMD is to control the transfer of the strategic items/technology to the countries which intend to develop the WMD in accordance with the multilateral agreements of the Nuclear Supply Group (NSG), Wassenaar Agreement (WA), Austrian Group (AG) and Missile Technology Control Regime (MTCR). Among them, export controls at KAERI are deeply related to the guidelines of the NSG, an international nuclear export control regime. Since the new concept of an export system was launched in Jan. 2014, KAERI needs to consider new approaches to meet the requirement of the revised domestic law and regulation. To cope with this environmental change, this paper suggests new approaches to effectively conduct the export control at KAERI

  15. Experimental Study of Na based Titanium Nanofluid-Water Reaction

    Park, Gunyeop; Kim, Soo Jae; Baek, Jehyun; Kim, Hyun Soo; Oh, Sun Ryung; Park, Hyun Sun; Kim, Moo Hwan [POSTECH, Pohang (Korea, Republic of)

    2015-10-15

    In KALIMER-600, a sodium-cooled fast reactor designed by KAERI, thermal energy is transported from high-temperature liquid Na (526 .deg. C at 0.1 MPa) to low temperature water (230 .deg. C at - 19.5 MPa) through a heat exchanger. If any leakage or rupture occurs during the operation of this heat exchanger, highly pressurized liquid water can penetrate into the liquid Na channels; this contact should instantly cause SWR. As reaction continues, liquid water is soon vaporized by pressure drop and huge amount of reaction heat. This generated water vapor expands large reaction area and increases sodium-water vapor reaction process. Therefore, the rapid generation of reaction product (like H{sub 2}) and water vapor increases the system pressure that can cause the system failure in SFR. To reduce this strong chemical reaction phenomena between Na and water, some we have focused on suppressing the chemical reactivity of liquid Na by dispersing nanoparticles (NPs). For the real application of NaTiNF, the pressure change induced by NaTiNF-water reaction is compared with Na-water reaction in the present study. NaTiNF contains 100nm of Ti NPs at 0.2 vol. %. The reaction rate of NaTiNF-water reaction is also investigated as reaction temperature increases. Sodium-water vapor reaction (SVR) will occur when an SWR accident occurs in SFR. In this manner, NaTiNF-water vapor reaction is experimentally performed for ensuring the suppression of chemical reactivity of NaTiNF in contact with water vapor. In the basic step for reducing risk of an SWR in SFR, we have experimentally verified the suppressed chemical reactivity of liquid sodium using Ti NPs through SWR and SVR experiments. In SWR, Na based titanium nanofluid (NaTiNF) shows lower pressure change than Na. As T{sub R} increases, P{sub max} in Na-water reaction increases while NaTiNF does not. The reaction rate of NaTiNF shows twice slower than that of Na. In SVR, NaTiNF shows slower temperature increase than Na. The distinct

  16. Status of research reactor fuel development in KAERI

    Kim, Chang-Kyu; Ryu, Woo-Seok; Park, Jong-Man; Lee, Don-Bae; Kim, Ki-Hwan; Kuk, Il-Hyun

    1996-01-01

    The development of uranium silicide dispersion fuel fabrication technology has been carried out in KAERI. LEU fuel bundle was prepared for irradiation test. In order to compare the performance of atomized and comminuted U 3 Si dispersed fuels, the bundle of two kinds of fuel elements were prepared. Irradiation test will be performed in the OR-hole of HANARO in the near future. U 3 Si 2 atomization technology has been improved by using ceramic crucible and nozzle. Irradiation test for atomized U 3 Si 2 plate type fuel will be carried out in cooperation with ANL by using HANARO in connection with RERTR advanced fuel development. (author)

  17. Analysis of Trends in Cooperative Network Patterns for KAERI Researchers

    Chun, Young Choon; Lee, Hyun Soo

    2016-01-01

    There has been a trend toward faster results of research and accelerating inter-disciplinary convergence, under constraints in available resources. Under such reality, national and international cooperation with inter-sectoral research on science-technology-industry is becoming inevitable as a strategic approach for enhancing competitive edge on global dimension. This study gives an analysis on the cooperative network in nuclear research which bears multi-disciplinary technical feature. The study aims to visualize the cooperative network of KAERI(Korea Atomic Energy Research Institute) researchers, as the hub of the network, including academics and industry, with a view to provide insight on strengthening the cooperative network in nuclear research. This study accounted for the paper entries in SCI(E) in 2013 (538 papers) and 2015 (551 papers) with a view to identify cooperative research activities centered for KAERI. On international cooperation, the analysis showed a trend toward, first of all, diversification of partner countries. There were 118 entries of co-authorship with 22 countries in 2013 (41 with USA, 12 with Japan, 9 with India), which evolved to 121 entries in 2015 (34 for USA, 11 with China, 10 each with Japan and India). Secondly, there was a trend toward more number of countries evenly spread in 2015 compared to 2013, except a few major countries like USA, Japan, and India

  18. Design and progress of the SPHINX in KAERI

    Kim, Hyung Rae; Kim, Hwan Teol; Song, Jin Ho; Kim, Hee Dong; Bae Yoon Yeong

    2005-01-01

    The SCWR (SuperCritical Water-cooled Reactor) is one of the six reactor candidates selected in the Gen-IV project, which aims at the development of new reactors with enhanced economy and safety. The SCWR is considered to be a feasible concept of new nuclear power plant if the existing technologies developed in fossil fuel fired plants and LWRs are incorporated together with additional researches on several disciplines such as materials, water chemistry, and safety. Among the research areas, heat transfer experiments under supercritical conditions are required for the proper prediction of thermal hydraulic phenomena, which are essential in the reactor core designs. A heat transfer test loop using carbon dioxide (CO 2 ) as a surrogate fluid has been constructed in KAERI. The test facility, named as SPHINX (Supercritical Pressure Heat transfer Investigation for NeXt generation), will be used for the study of heat transfer in a single tube, single rod, and rod bundle. The heat transfer correlations obtained from the SPHINX will be compared with the other correlations generated at Kyushu University and INL. This paper describes the design characteristics and progress of the SPHINX in KAERI. The construction of the facility is completed and a trial run is being conducted. The test and the data production are expected to start by April 2005

  19. Design and progress of the SPHINX in KAERI

    Kim, Hyung Rae; Kim, Hwan Teol; Song, Jin Ho; Kim, Hee Dong; Bae Yoon Yeong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2005-07-01

    The SCWR (SuperCritical Water-cooled Reactor) is one of the six reactor candidates selected in the Gen-IV project, which aims at the development of new reactors with enhanced economy and safety. The SCWR is considered to be a feasible concept of new nuclear power plant if the existing technologies developed in fossil fuel fired plants and LWRs are incorporated together with additional researches on several disciplines such as materials, water chemistry, and safety. Among the research areas, heat transfer experiments under supercritical conditions are required for the proper prediction of thermal hydraulic phenomena, which are essential in the reactor core designs. A heat transfer test loop using carbon dioxide (CO{sub 2}) as a surrogate fluid has been constructed in KAERI. The test facility, named as SPHINX (Supercritical Pressure Heat transfer Investigation for NeXt generation), will be used for the study of heat transfer in a single tube, single rod, and rod bundle. The heat transfer correlations obtained from the SPHINX will be compared with the other correlations generated at Kyushu University and INL. This paper describes the design characteristics and progress of the SPHINX in KAERI. The construction of the facility is completed and a trial run is being conducted. The test and the data production are expected to start by April 2005.

  20. Analysis of Trends in Cooperative Network Patterns for KAERI Researchers

    Chun, Young Choon; Lee, Hyun Soo [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    There has been a trend toward faster results of research and accelerating inter-disciplinary convergence, under constraints in available resources. Under such reality, national and international cooperation with inter-sectoral research on science-technology-industry is becoming inevitable as a strategic approach for enhancing competitive edge on global dimension. This study gives an analysis on the cooperative network in nuclear research which bears multi-disciplinary technical feature. The study aims to visualize the cooperative network of KAERI(Korea Atomic Energy Research Institute) researchers, as the hub of the network, including academics and industry, with a view to provide insight on strengthening the cooperative network in nuclear research. This study accounted for the paper entries in SCI(E) in 2013 (538 papers) and 2015 (551 papers) with a view to identify cooperative research activities centered for KAERI. On international cooperation, the analysis showed a trend toward, first of all, diversification of partner countries. There were 118 entries of co-authorship with 22 countries in 2013 (41 with USA, 12 with Japan, 9 with India), which evolved to 121 entries in 2015 (34 for USA, 11 with China, 10 each with Japan and India). Secondly, there was a trend toward more number of countries evenly spread in 2015 compared to 2013, except a few major countries like USA, Japan, and India.

  1. Experience and Know-How Sharing Project at KAERI

    Lee, H.; Oh, J.; Lee, Y.

    2016-01-01

    Full text: With its long history of over 50 years, KAERI (Korea Atomic Energy Research Institute) has produced a large amount of information and explicit knowledge such as experiment data, database, design data, report, instructions, and operation data at each stage of its research and development process as it has performed various researches since its establishment. Also, a lot of tacit knowledge has been produced both knowingly and unknowingly based on the experience of researchers who have participated in many projects. However, in the research environment in Korea where they focus overly on the output, tacit knowledge has not been managed properly compared to explicit knowledge. This tacit knowledge is an asset as important as explicit knowledge for an effective research and development. Moreover, as the first generation of atomic energy and research manpower retire, their accumulated experience and knowledge are in danger of disappearing. Therefore, in this study, we sought how to take a whole view and to document atomic energy technology researched and developed by KAERI, from the background to achievement of each field of the technology. (author

  2. Establishment of database system for management of KAERI wastes

    Shon, J. S.; Kim, K. J.; Ahn, S. J.

    2004-07-01

    Radioactive wastes generated by KAERI has various types, nuclides and characteristics. To manage and control these kinds of radioactive wastes, it comes to need systematic management of their records, efficient research and quick statistics. Getting information about radioactive waste generated and stored by KAERI is the basic factor to construct the rapid information system for national cooperation management of radioactive waste. In this study, Radioactive Waste Management Integration System (RAWMIS) was developed. It is is aimed at management of record of radioactive wastes, uplifting the efficiency of management and support WACID(Waste Comprehensive Integration Database System) which is a national radioactive waste integrated safety management system of Korea. The major information of RAWMIS supported by user's requirements is generation, gathering, transfer, treatment, and storage information for solid waste, liquid waste, gas waste and waste related to spent fuel. RAWMIS is composed of database, software (interface between user and database), and software for a manager and it was designed with Client/Server structure. RAWMIS will be a useful tool to analyze radioactive waste management and radiation safety management. Also, this system is developed to share information with associated companies. Moreover, it can be expected to support the technology of research and development for radioactive waste treatment

  3. Surveillance and analysis of nuclear R and D manpower for efficient utilization of KAERI's nuclear R and D resources

    Kim, Hyun Jun; Yang, M. H.; Song, K. D.; Chung, W. S.; Yun, S. W.; Won, B. C.; Yoon, H. M.

    1999-11-01

    This study aimed at securing row data on KAERI's manpower resources, which be useful to establish the short and long term R and D policy of KAERI. To coincide with the objectives, this study covered following scopes; (1) identification of status and issues of manpower in science and technology fields, (2) identification of status and issues of KAERI's manpower management policy, (3) gathering row data on KAERI's manpower through surveillance and analysis, and analyzing staff's perception on KAERI's manpower utilization policy, (4) suggestion of short and long term policy direction of manpower management of KAERI. (author)

  4. Summary of the Safety Culture Activities in HANARO of KAERI

    Lim, In-Cheol; Wu, Jong-Sup; Lee, Kye-Hong

    2006-01-01

    The definition of safety culture in HANARO takes the IAEA's definition and it is the assembly of characteristics of attitudes in the HANARO center and individuals which establishes that, as an overriding priority, the HANARO safety issues receive the attention warranted by their significance. Since the power operation of HANARO started in 1996, HANARO has been operated for about 11 years and its degree of utilization and the number of experimental facilities have increased. This achievement is partly due to the spread of safety culture to the operators and the reactor users. In this paper, the safety culture activities done by the HANARO center of KAERI are described, and its efforts necessary for an improvement of it are presented

  5. Reliability analysis of digital I and C systems at KAERI

    Kim, Man Cheol

    2013-01-01

    This paper provides an overview of the ongoing research activities on a reliability analysis of digital instrumentation and control (I and C) systems of nuclear power plants (NPPs) performed by the Korea Atomic Energy Research Institute (KAERI). The research activities include the development of a new safety-critical software reliability analysis method by integrating the advantages of existing software reliability analysis methods, a fault coverage estimation method based on fault injection experiments, and a new human reliability analysis method for computer-based main control rooms (MCRs) based on human performance data from the APR-1400 full-scope simulator. The research results are expected to be used to address various issues such as the licensing issues related to digital I and C probabilistic safety assessment (PSA) for advanced digital-based NPPs. (author)

  6. The status and latest issues on KAERI export control implementation

    Kim, Hyun Sook; Park, Ho Jun; Kim, Hyun Jo; Ko, Han Suk; Lee, Byung Doo

    2010-01-01

    There are four informal non-proliferation arrangements which seek to control the proliferation of weapons of mass destruction and their missile delivery systems and the transfer of conventional weapons and dual-use technologies. The four arrangements are Wassenaar Arrangement (WA) on export controls for conventional arms and dual use goods and technologies, Nuclear Supplies Group(NSG), Missile Technology Control Regime(MTCR) and Australia Group(AG) on chemical and biological weapons materials. ROK participates in four arrangements to seek to encourage responsible practice in the trade of strategic goods and technologies. It is achieved through the implementation of export control list. MKE Notification (Ministry of Knowledge Economy Notification No. 2009-250) specifies those items and technologies subject to control. In this paper, the status and latest issues on KAERI export control implementation are described

  7. DUPIC fuel fabrication using spent PWR fuels at KAERI

    Kim, Ho Dong; Yang, Myung Seung; Ko, Won Il and others

    2000-12-01

    This document contains DUPIC fuel cycle R and D activities to be carried out for 5 years beyond the scope described in the report KAERI/AR-510/98, which was attached to Joint Determination for Post-Irradiation Examination of irradiated nuclear fuel, by MOST and US Embassy in Korea, signed on April 8, 1999. This document is purposely prepared as early as possible to have ample time to review that the over-all DUPIC activities are within the scope and contents in compliance to Article 8(C) of ROK-U.S. cooperation agreement, and also maintain the current normal DUPIC project without interruption. Manufacturing Program of DUPIC Fuel in DFDF and Post Irradiation Examination of DUPIC Fuel are described in Chapter I and Chapter II, respectively. In Chapter III, safeguarding procedures in DFDF and on-going R and D on DUPIC safeguards such as development of nuclear material accounting system and development of containment/surveillance system are described in details.

  8. Recent Progress on the DUPIC Fuel Fabrication Technology at KAERI

    Jung-Won Lee; Ho-Jin Ryu; Geun-Il Park; Kee-Chan Song

    2008-01-01

    Since 1991, KAERI has been developing the DUPIC fuel cycle technology. The concept of a direct use of spent PWR fuel in Candu reactors (DUPIC) is based on a dry processing method to re-fabricate Candu fuel from spent PWR fuel without any intentional separation of the fissile materials and fission products. A DUPIC fuel pellet was successfully fabricated and the DUPIC fuel element fabrication processes were qualified on the basis of a Quality Assurance program. Consequently, the DUPIC fuel fabrication technology was verified and demonstrated on a laboratory-scale. Recently, the fuel discharge burn-up of PWRs has been extended to reduce the amount of spent fuel and the fuel cycle costs. Considering this trend of extending the fuel burn-up in PWRs, the DUPIC fuel fabrication technology should be improved to process high burn-up spent fuels. Particularly the release behavior of cesium from the pellet prepared with a high burn-up spent fuel was assessed. an improved DUPIC fuel fabrication technology was experimentally established with a fuel burn-up of 65,000 MWd/tU. (authors)

  9. The Enhancement of Nuclear Control and Emergency Preparedness Systems in KAERI

    Lee, Goan Yup; Lee, B. D.; Kim, J. S.; Park, H. J.

    2008-12-01

    The objective of this study is to foster international environment for peaceful nuclear technology based on the international transparency with respect to the control, management and surveillance system. In this regards, this study establishes, operates and upgrades the nuclear control and management information system of the KAERI that assumed the prerequisite means for Integrated Safeguards systems of the IAEA which is implemented from the July of 2008. It is also included the radiological emergency system that contains the safety information surveillance system in KAERI to meet the national legislative requirements. The nuclear control and management information system of the KAERI could be controlled and managed the accounting information of the nuclear facility with on-line manner. This system enhances transparency of accounting management of the KAERI in terms of effective ways for the Agency inspectors and national inspectors to implement the no-notice inspection under the Integrated Safeguards system. To complete the nuclear safety information collecting and monitoring system at EOF for KAERI, the real-time remote monitoring systems for RIPF, IMEF, PIEF were established. In addition, after the review of the abnormal condition of RMS data, the notification system for a radiation abnormal condition at nuclear facilities was operated. And also, the server of emergency management system was improved, the emergency situation notification system to all KAERI and KNF site was established

  10. Proceedings of the third JAERI-KAERI joint seminar on post irradiation examination technology

    1999-09-01

    Between the Department of JMTR of the Japan Atomic Energy Research Institute (JAERI) and the Nuclear Fuel Cycle Research Group of the Korea Atomic Energy Research Institute (KAERI), it has been periodically carried out the collaboration on technical information exchange by specialists and scientists, under the Arrangement of the Implementation of Cooperative Research Program in the Field of Peaceful Uses of Nuclear between JAERI and KAERI. And JAERI-KAERI joint seminar has been held every three years. The 1st and 2nd JAERI-KAERI Joint Seminars were held in November 1992 at JAERI and in September 1995 at KAERI, respectively. The 3rd JAERI-KAERI Joint Seminar was held on 25 and 26 March, 1999 at the Oarai Research Establishment of JAERI. In this seminar, total participants of 84 were joined from JAERI, KAERI, Hanyang University, Japan Nuclear Cycle Development Institute, Oarai Branch of Institute for Materials Research (IMR) of Tohoku University, Nippon Nuclear Fuel Development Co., Ltd., Nuclear Development Corporation and others. Contributed presentations were in three sessions; Current status and future perspectives on PIE, PIE techniques and Evaluation of PIE data. Re-assembling technique for JOYO fuel, Nd-YAG laser welding technique, grain boundary analysis using FEG-TEM, lift time estimation of PWR Rod Cluster Control Assembly (RCCA) rodlet and failure analysis of Korea Nuclear Power Plant (KNP) fuel have been widely noticed as topic items on PIE. And some comments from PIE user, were pointed out that the nano-PIE technique, the flexibility to ad-hoc demands on testing space or utilization, and the international collaboration were very important for the next generation's PIE. The 34 of the present papers are indexed individually. (J.P.N.)

  11. Proceedings of the third JAERI-KAERI joint seminar on post irradiation examination technology

    NONE

    1999-09-01

    Between the Department of JMTR of the Japan Atomic Energy Research Institute (JAERI) and the Nuclear Fuel Cycle Research Group of the Korea Atomic Energy Research Institute (KAERI), it has been periodically carried out the collaboration on technical information exchange by specialists and scientists, under the Arrangement of the Implementation of Cooperative Research Program in the Field of Peaceful Uses of Nuclear between JAERI and KAERI. And JAERI-KAERI joint seminar has been held every three years. The 1st and 2nd JAERI-KAERI Joint Seminars were held in November 1992 at JAERI and in September 1995 at KAERI, respectively. The 3rd JAERI-KAERI Joint Seminar was held on 25 and 26 March, 1999 at the Oarai Research Establishment of JAERI. In this seminar, total participants of 84 were joined from JAERI, KAERI, Hanyang University, Japan Nuclear Cycle Development Institute, Oarai Branch of Institute for Materials Research (IMR) of Tohoku University, Nippon Nuclear Fuel Development Co., Ltd., Nuclear Development Corporation and others. Contributed presentations were in three sessions; Current status and future perspectives on PIE, PIE techniques and Evaluation of PIE data. Re-assembling technique for JOYO fuel, Nd-YAG laser welding technique, grain boundary analysis using FEG-TEM, lift time estimation of PWR Rod Cluster Control Assembly (RCCA) rodlet and failure analysis of Korea Nuclear Power Plant (KNP) fuel have been widely noticed as topic items on PIE. And some comments from PIE user, were pointed out that the nano-PIE technique, the flexibility to ad-hoc demands on testing space or utilization, and the international collaboration were very important for the next generation's PIE. The 34 of the present papers are indexed individually. (J.P.N.)

  12. Proceedings of 2008 KAERI/JAEA joint seminar on advanced irradiation and PIE technologies

    Ryu, Woo-Seog; Ishihara, Masahiro

    2008-12-01

    Under the Arrangement for Cooperation in the field of peaceful uses of Nuclear Energy between the Korea Atomic Energy Research Institute (KAERI) and the Japan Atomic Energy Agency (JAEA), the 2008 KAERI-JAEA Joint Seminar on Advanced Irradiation and PIE (post-irradiation examination) Technologies has been held at KAERI in Daejeon, Korea, from November 5 to 7, 2008. This seminar was organized by the PIE and Radwaste Division, Research Reactor Engineering Division, and HANARO Management Division in KAERI. It was also the first time to hold the seminar under the agreement signed September 4, 2008. This triennial seminar is the sixth in series of bilateral exchange of irradiation technologies. Since the first joint seminar on Post Irradiation Examination Technology between JAERI and KAERI held at JAERI Oarai center, Japan in 1992, it has been a good model of international cooperation program between KAERI and JAEA in the field of neutron irradiation uses. At the fifth seminar in 2005, irradiation technology field was included to the joint seminar, moreover in this time it is expanded to the research reactor management field for covering whole areas of irradiation using in research reactors. The seminar was divided into three technical sessions; the sessions addressed the general topics of 'research reactor management', 'advanced irradiation technology' and 'post-irradiation examination technology'. Total 46 presentations were made, and active information exchange was done among participants. This proceeding is containing the papers or manuscripts presented in the 2008 KAERI-JAEA Joint Seminar on Advanced Irradiation and PIE Technologies. The 46 of the presented papers indexed individually. (J.P.N.)

  13. In-pile irradiation test program and safety analysis report of the KAERI fuel for HANARO

    Hwang, Wan; Ryu, Woo Suck; Byun, Taek Sang; Park, Jong Man; Lee, Byung Chul; Kim, Hack No; Park, Hee Tae; Kim, Chang Kyu [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1996-05-01

    Localization of HANARO fuel has been carried out successfully, and design and fabrication technologies of the fuel are recently arrived the final stage of development. The performance of the fuel which has been fabricated in KAERI is confirmed through out-of-pile characterization, and the quality assurance procedure and assessment criteria are described. In order to verify the KAERI fuel, thus, in-pile irradiation test program of the KAERI fuel is scheduled in HANARO. This report summarizes the in-pile testing schedule, design documents of test rods and assemblies, fabrication history and out-of-pile characteristics of test rods, irradiation test condition and power history, post-irradiation examination scheme, linear power generation distribution, and safety analysis results. The design code for HANARO fuel is used to analyze the centerline temperature and swelling of the KAERI fuels. The results show that at 120 kW/m of linear power the maximum centerline temperature is 267 deg C which is much lower than the limitation temperature of 350 deg C, and that the swelling is 9.3 % at 95 at% lower than criterion of 20 %. Therefore, the KAERI fuels of this in-pile irradiation test is assessed to show good performance of integrity and safety in HANARO. 10 tabs., 7 figs., 3 refs. (Author).

  14. Proceedings of 2012 JAEA/KAERI joint seminar on advanced irradiation and PIE technologies

    Ishihara, Masahiro; Ishitsuka, Etsuo; Suzuki, Masahide

    2012-12-01

    Under the 'Arrangement for Corporation in the field of peaceful uses of Nuclear Energy between the Japan Atomic Energy Agency (JAEA) and the Korean Atomic Energy Research Institute (KAERI)', the 2012 JAEA/KAERI Joint Seminar on Advanced Irradiation and PIE (post-irradiation examination) Technologies has been held at Mito, Japan from March 28 to 30, 2012. This triennial seminar is the seventh in series of bilateral exchange of irradiation and PIE technologies and research reactor management. Since the first joint seminar on the PIE Technology between JAERI (Japan Atomic Energy Research Institute, former agency of JAEA) and KAERI was held at JAERI Oarai Research Institute, Japan in 1992, the international cooperation program between JAEA and KAERI has been actively carried out in the field of neutron irradiation. At the fifth seminar in 2005 and sixth in 2008, the irradiation technology and the research reactor management fields were included, respectively, to the joint seminar, and it covers whole areas of irradiation using research reactors. In this seminar total 37 presentations were made in three technical sessions, which are 'research reactor management', 'advanced irradiation technology' and 'post-irradiation examination technology', and active information exchange was done among participants. Papers or manuscripts presented in the 2012 JAEA/KAERI Joint Seminar on Advanced Irradiation and PIE Technologies are contained in the proceedings. (author)

  15. Large leak sodium-water reaction code SWACS and its validation

    Miyake, O.; Shindo, Y.; Hiroi, H.; Tanabe, H.; Sato, M.

    1982-01-01

    A computer code SWACS for analyzing the large leak accident of an LMFBR steam generators has been developed and validated. Five tests data obtained by SWAT-3 test facility were compared with code results. In each of SWAT-3 tests, a double-ended guillotine rupture of one tube was simulated in a helical coil steam generator model with 1/2.5 scaled test vessel to the prototype SG. The analytical results, including an initial pressure spike, a propagated pressure in a secondary system, and a quasi-steady pressure, indicate that the overall large-leak event could be predicted in reasonably good agreement

  16. Advanced signal processing techniques for acoustic detection of sodium/water reaction

    Yughay, V.S.; Gribok, A.V.; Volov, A.N.

    1997-01-01

    In this paper results of development of a neural network technique for processing of acoustic background noise and injection noise of various media (argon, water steam, hydrogen) at test rigs and industrial steam generator are presented. (author). 3 refs, 9 figs, 3 tabs

  17. Detection of sodium/water reaction in a steam generator: Results of a 1995 benchmark test

    Oriol, L.

    1997-01-01

    The CEA analysis of the 1995 benchmark test has been focused on the location of the injections. Two techniques have been tested: the pulse timing technique, and the time-domain delay and sum beamforming technique. The two methods gave coherent locations of the injector even if there was a difference of 25% of the SGU height between the vertical locations. Prior to that analysis, the RMS values of the signals were calculated in different frequency bands. The results obtained in the 200-1000 Hz were used to draw a rough estimation of the beginnings of the injections in order to determine the parts of the records on which the location signal processing can be carried out. (author). 2 refs, 8 figs, 2 tabs

  18. Sodium-water reaction data needed by a utility for design assessment purposes

    Bolt, P R [Fast Reactor Engineering, Barnwood, Gloucester (United Kingdom)

    1978-10-01

    Worldwide LMFBR experience has shown that LMFBR steam generator water/steam leakage into sodium can severely reduce steam generator availability and cause lengthy plant outages. Utility assessment LMFBR designs prior to placing an order to construct are likely to give emphasis to matters that can affect steam generator integrity, reliability and total operating cost. The data needed in carrying out such assessments is described. (author)

  19. Sodium-water reaction data needed by a utility for design assessment purposes

    Bolt, P.R.

    1978-01-01

    Worldwide LMFBR experience has shown that LMFBR steam generator water/steam leakage into sodium can severely reduce steam generator availability and cause lengthy plant outages. Utility assessment LMFBR designs prior to placing an order to construct are likely to give emphasis to matters that can affect steam generator integrity, reliability and total operating cost. The data needed in carrying out such assessments is described. (author)

  20. The KAERI 10 MeV Electron Linac - Description and Operational Manual

    Lee, Byung Cheol; Park, Seong Hee; Jung, Young Uk; Han, Young Hwan; Kang, Hee Young

    2005-06-01

    The objective of this technical report is to guide the right operation and maintenance of the KAERI electron linac system. The KAERI electron linac system consists of 2 MeV injector based on 176 MHz Normal conducting RF (Radio Frequency)cavity and 10 MeV main accelerator based on 352 MHz Superconducting RF cavity, electron beamlines (injection and extraction). Since a electron accelerator generates hazard radiation, this system is located at the shielded room in basement and we can operate the system using the remote control system. It includes the description and the operational manual as well as the detailed technical direction for trouble shooting

  1. The KAERI 10 MeV Electron Linac - Description and Operational Manual

    Lee, Byung Cheol; Park, Seong Hee; Jung, Young Uk; Han, Young Hwan; Kang, Hee Young

    2005-06-15

    The objective of this technical report is to guide the right operation and maintenance of the KAERI electron linac system. The KAERI electron linac system consists of 2 MeV injector based on 176 MHz Normal conducting RF (Radio Frequency)cavity and 10 MeV main accelerator based on 352 MHz Superconducting RF cavity, electron beamlines (injection and extraction). Since a electron accelerator generates hazard radiation, this system is located at the shielded room in basement and we can operate the system using the remote control system. It includes the description and the operational manual as well as the detailed technical direction for trouble shooting.

  2. Post-irradiation examination and R and D programs using irradiated fuels at KAERI

    Chun, Yong Bum; Min, Duck Kee; Kim, Eun Ka and others

    2000-12-01

    This report describes the Post-Irradiation Examination(PIE) and R and D programs using irradiated fuels at KAERI. The objectives of post-irradiation examination (PIE) for the PWR irradiated fuels, CANDU fuels, HANARO fuels and test fuel materials are to verify the irradiation performance and their integrity as well as to construct a fuel performance data base. The comprehensive utilization program of the KAERI's post-irradiation examination related nuclear facilities such as Post-Irradiation Examination Facility (PIEF), Irradiated Materials Examination Facility (IMEF) and HANARO is described

  3. Post-irradiation examination and R and D programs using irradiated fuels at KAERI

    Chun, Yong Bum; So, Dong Sup; Lee, Byung Doo; Lee, Song Ho; Min, Duck Kee

    2001-09-01

    This report describes the Post-Irradiation Examination(PIE) and R and D programs using irradiated fuels at KAERI. The objectives of post-irradiation examination (PIE) for the PWR irradiated fuels, CANDU fuels, HANARO fuels and test fuel materials are to verify the irradiation performance and their integrity as well as to construct a fuel performance data base. The comprehensive utilization program of the KAERI's post-irradiation examination related nuclear facilities such as Post-Irradiation Examination Facility (PIEF), Irradiated Materials Examination Facility (IMEF) and HANARO is described

  4. Korea Atomic Energy Research Institute (KAERI) in the 21st century

    Chang, In Soon; Lee, Mun-Ki

    2001-01-01

    Abstract. KAERI (Korea Atomic Energy Research Institute), a national nuclear research institute in the Republic of Korea, celebrated its fortieth anniversary last April. It has played a key role in the Korean nuclear history such that it: initiated and promoted the peaceful uses of nuclear energy in the Republic of Korea; maintained nuclear expertise on whole spectrum of nuclear field through conducting nuclear R and D programs, operating nuclear research facilities, and training and educating specialized nuclear personnel; founded a cornerstone of Korean nuclear industry by participating in the establishment of a nuclear engineering company and a nuclear fuel company and localizing nuclear fuel and reactor technology; and contributed to nuclear safety regulation by incubating a specialized nuclear regulatory body. Recently, to concentrate on nuclear R and D on advanced technology, KAERI went through management reform such as: the transfer of nuclear engineering divisions responsible for NSSS design and nuclear fuel design to nuclear industry in 1996; and the downsizing of manpower in 1998. Currently KAERI is in the challenging stage in terms of its missions and manpower. In the coming 21st century, KAERI is required to maintain the current R and D momentum and also to conduct priority-based research requiring concentrated effort. (author)

  5. The Status of Development on a Web-Based Nuclear Material Accounting System at KAERI

    Lee, Byungdoo; Kim, Inchul; Lee, Seungho; Kim, Hyunjo

    2014-01-01

    The Integrated Safeguards (IS) has been applied to 10 nuclear facilities and 1 location outside facility (LOF) at the Korea Atomic Energy Research Institute (KAERI) since July 2008. One of the major changes in the implementation of safeguards under the IS is to apply the concept of a Random Interim Inspection (RII) instead of an interim inspection. The RII plan is notified within a few hours under the IS. It is thus difficult for facility operators to prepare the inspection documents within a short time if they do not periodically manage and process the nuclear material accounting data at each facility. To resolve these issues, KAERI developed a Web-based accounting system with the function of a near real-time accounting (NRTA) system to effectively and efficiently manage the nuclear material accounting data produced at the nuclear facilities and cope with a short notice inspection under the IS, called KASIS (KAeri Safeguards Information treatment System). The facility operators must input the accounting data on the inventory changes, which are the transfers of nuclear materials among the nuclear facilities and the chemical/physical composition changes, into the KASIS. KAERI also established an RFID system for controlling and managing the transfer of nuclear material and/or radioactive materials between the nuclear facilities for the purpose of nuclear safety management, and developed the nuclear material accounting system with the functions of inventory management of nuclear material at the facility level

  6. The Status of Development on a Web-Based Nuclear Material Accounting System at KAERI

    Lee, Byungdoo; Kim, Inchul; Lee, Seungho; Kim, Hyunjo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    The Integrated Safeguards (IS) has been applied to 10 nuclear facilities and 1 location outside facility (LOF) at the Korea Atomic Energy Research Institute (KAERI) since July 2008. One of the major changes in the implementation of safeguards under the IS is to apply the concept of a Random Interim Inspection (RII) instead of an interim inspection. The RII plan is notified within a few hours under the IS. It is thus difficult for facility operators to prepare the inspection documents within a short time if they do not periodically manage and process the nuclear material accounting data at each facility. To resolve these issues, KAERI developed a Web-based accounting system with the function of a near real-time accounting (NRTA) system to effectively and efficiently manage the nuclear material accounting data produced at the nuclear facilities and cope with a short notice inspection under the IS, called KASIS (KAeri Safeguards Information treatment System). The facility operators must input the accounting data on the inventory changes, which are the transfers of nuclear materials among the nuclear facilities and the chemical/physical composition changes, into the KASIS. KAERI also established an RFID system for controlling and managing the transfer of nuclear material and/or radioactive materials between the nuclear facilities for the purpose of nuclear safety management, and developed the nuclear material accounting system with the functions of inventory management of nuclear material at the facility level.

  7. Status of the Decommissioning Project Management Information System Development of KAERI in 2015

    Jin, Hyung Gon; Park, Seungkook; Park, Heeseong; Song, Chanho

    2015-01-01

    Various information systems have been developed and used at decommissioning sites for planning a project, record keeping for a post management and cost estimation. KAERI is the only one expert group which has decommissioning experiences and KAERI is trying to develop computer code to converge all the data which has been accumulated during KRR-1 and 2 and UCP (Uranium Conversion Plant) decommission. KRR-1 and KRR-2 are TRIGA MARK type of research reactor which were constructed worldwide. Hence, there are many chance to use decommissioning experiences and data when other TRIGA MARK type of research reactors start to decommission. KAERI DPMIS stands for Decommissioning Project Management Information System, which is aiming to re-use of data effectively. As a responsible leading group of Korean decommissioning research field, KAERI has been developing DPMIS application program, which is going to be an important mile stone of decommission industry in Korea. User friendly graphical interface and lots of actual data let people well understood on decommission planning. It is expected that continuous effort and funds will be delivered to this research

  8. Status of the Decommissioning Project Management Information System Development of KAERI in 2015

    Jin, Hyung Gon; Park, Seungkook; Park, Heeseong; Song, Chanho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    Various information systems have been developed and used at decommissioning sites for planning a project, record keeping for a post management and cost estimation. KAERI is the only one expert group which has decommissioning experiences and KAERI is trying to develop computer code to converge all the data which has been accumulated during KRR-1 and 2 and UCP (Uranium Conversion Plant) decommission. KRR-1 and KRR-2 are TRIGA MARK type of research reactor which were constructed worldwide. Hence, there are many chance to use decommissioning experiences and data when other TRIGA MARK type of research reactors start to decommission. KAERI DPMIS stands for Decommissioning Project Management Information System, which is aiming to re-use of data effectively. As a responsible leading group of Korean decommissioning research field, KAERI has been developing DPMIS application program, which is going to be an important mile stone of decommission industry in Korea. User friendly graphical interface and lots of actual data let people well understood on decommission planning. It is expected that continuous effort and funds will be delivered to this research.

  9. A study on the mid- and long-term strategies of KAERI's future vision

    Yang, Maengho; Yun, S. W.; Chung, W. S.; Lee, D. S.

    2012-12-15

    In this study, KAERI's role, expected changes of KAERI's management environments and its implementational directions, strategical direction of nuclear R and D, and KAERI's future vision and sustainable growth strategies beyond the up-to date successful achievements were analysed. The purpose of this study is investigating recent rapid changes of KAERI's political and management environments to establish future vision and growth strategies of KAERI in the 21st centuries. KAERI has performed its' mission as a government funded research organization successfully and significantly contributed promotion of national nuclear industry and capabilities through manpower development and self-reliance of nuclear power technologies and academic advancement in the fields of nuclear energy. That way, it has contributed to supply stable energy and develop economy and industry as well. In order to respond properly to newly emerged missions, integral and systematic institutional efforts are required to secure more research findings from the central and local Government and industries as well. High-quality human resources having creative expertise, experiences and skills are pre-requisite for securing competitiveness of nuclear technologies and industries. So it is essential to request the Governmental support and establish the manpower development plan in long term bases. KAERI is now standing at the turning moment to take off from the catch-up strategy of the advanced nuclear technologies (KAERI 1.0) into the innovative and creative vision and challenges, that is to say, KAERI 2.0, to establish an new technological culture, respond to social requirements and seek the international leading role.

  10. Beam diagnostics for Laser-induced proton generation at KAERI

    Kim, Dong Heun; Park, Seong Hee; Jeong, Young Uk; Lee, Ki Tae; Chan, Young Ho; Lee, Byung Cheol; Yoo, Byeong Duk

    2005-01-01

    With an advent of femto-second lasers, a laseraccelerated ion generation has been world-widely studied for medical and nuclear applications. It is known that protons with the energy from several tens MeV to a few hundreds MeV require for a cancer therapy and nuclear reaction. Even though, up to present, the maximum energy of laser-accelerated proton is about 60 MeV, it is expected that the energy of protons generated can be obtained at least up to 150 MeV. According to theoretical and experimental works, it turns out the energy distribution and the flux of ions strongly depends on the intensity of a fs laser at a target. However, physics on laser-plasma interaction is still not clear. The precise measurements of parameters of a fs laser and ions are important to figure out the physics and develop the theoretical interpretation. Typically, beam diagnostic system includes measurements and/or monitoring of the temporal and spatial profiles of lasers at the target as well as the energy spectrum and density profile of protons, which are critical for the analysis of mechanism and the characterization of protons generated. We fabricated and installed the target chamber for laser-accelerated proton generation and are now integrating beam diagnostic system. For laser diagnostics, beam monitoring and alignment system has been installed. For a charged particle, CR-39 detectors, Thomson parabola spectrometer, and Si charged particle detectors are installed for density profile and energy spectrum. In this paper, we discuss the laser beam monitoring and alignment system. We also estimates expected spectrum of protons from Thomson parabola spectrometer, depending on the parameters of protons

  11. The development of KAERI management information system (II) -The development of Time Sheet Management System-

    Kang, Sin Bok; Kim, Yeong Taek; Park, Soo Jin; Ko, Yeong Cheol; Lee, Jong Bok; Han, Eun Sook; Kim, Hyeon Jeong

    1994-01-01

    The purpose of this report is to describe the work done for the development, operation and maintenance of Time Sheet Management System. This work is a part of the development KAERI management information system. Manpower management is essential to cope with the external circumstances promptly and to maximize the productivity of the organization. This work aims at setting up a basis for the manpower management system. It is widely recognized that neither timely decision making nor competitive edge can be secured with the traditional management technology in so a rapidly changing situations home and abroad, which can be characterized by openness and informality. The necessity of efficient and scientific man-power management by time-study has emerged on the reorganization of KAERI by expanding matrix system in order to enhance the R and D productivity. (Author)

  12. Economic Evaluation Methodology Review on KAERI's Recent Projects

    Cho, Jin Sam; Kim, Jee Young [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    In technology utilization, economics evaluation is helpful to R and D program managers by giving them economic information needed to improve the usefulness of their projects. Moreover it can help them to communicate to others participants keeping all of them value-oriented minded through the whole development process. In this context, KAERI(Korea Atomic Energy Research Institute) has been performed economic evaluation on recent some projects. So, in this study, it has been made brief reviews on KAERI's economic evaluation methodology to its recent some projects of which evaluation we engage in, especially PEFP(Proton Engineering frontier Project) and SMART(Small Medium advanced ReacTor): Methodology comparison and their pros and cons

  13. The development of KAERI NHRD model with consideration of IAEA milestone approach

    Noh, Byongchull; Kim, Hyunki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    KAERI has continuously tried to find efficient way for how shall do and how to cooperate with developing countries on the field of nuclear HRD but it was very difficult especially for proper answer on how Korea could achieve technology self-reliance on nuclear field so shortly and which strategy was adopted in the HRD area. To answer on this question raised by new comer country, KAERI tried to form nuclear human resource development model based on Korean experience. With this new nuclear HRD model, KAERI might share his experience very efficiently with developing countries who want to develop nuclear activities and support them. In this paper, two lines for competency were defined as education and training and this did not touch on academic education area because KAERI did not have his expertise on that. As defined in the introduction, this model is not finalized because of exception on academic education and matured industrial training. This model wants to raise issue on the establishment of national comprehensive nuclear HRD model to cope with new comer’s question properly and well understanding of Korean HRD in Korea as well. Therefore, it needs to be updated continuously with cooperation among Korean nuclear society and government level as soon as possible. However, this paper hopes that the issue to emphasize national nuclear HRD model as whole spectrum will be undertaken. When the real comprehensive NHRD model is established eventually in some time, Korean NHRD might be a global leader actually and could promote nuclear industry by cooperation with developing countries.

  14. Blasting Impact by the Construction of an Underground Research Tunnel in KAERI

    Kwon, S.; Cho, W. J.

    2005-12-01

    The underground research tunnel, which is under construction in KAERI for the validation of HLW disposal system, is excavated by drill and blasting method using high-explosives. In order not to disturb the operation at the research facilities such as HANARO reactor, it is critical to develop a blasting design , which will not influence on the facilities, even though several tens of explosives are detonated almost simultaneously. To develop a reasonable blasting design, a test blasting at the site should be performed. A preliminary analysis for predicting the expected vibration and noise by the blasting for the construction of the underground research tunnel was performed using a typical empirical equation. From the study, a blasting design could be developed not to influence on the major research facilities in KAERI. For the validation of the blasting design, a test blasting was carried out at the site and the parameters of vibration equation could be determined using the measured data during the test blasting. Using the equation, it was possible to predict the vibration at different locations at KAERI and to conclude that the blasting design would meet the design criteria at the major facilities in KAERI. The study would verify the applicability of blasting method for the construction of a research tunnel in a rock mass and that would help the design and construction of large scale underground research laboratory, which might be carried out in the future. It is also meaningful to accumulate technical experience for enhancing the reliability and effectiveness of the design and construction of the HLW disposal repository, which will be constructed in deep underground by drill and blasting technique

  15. Study on status of nuclear export/import implementation in KAERI

    Kim, H. J.; Lee, B. D.; Lee, S. H.; Park, H. J.; So, D. S.

    2004-01-01

    As Korea is the member of ZC(Zangger Committee) and NSG(Nuclear Suppliers Group), domestic legislation reflected their guideline of nuclear export. The paper investigate the status of implementation procedures of nuclear export and import in KAERI based on domestic and international law. In addition, the paper analyzes on problem of export/import implementation system and also extract the efficient implementation system of nuclear export and import

  16. Simulation of the KAERI PASCAL Test with MARS-KS and TRACE Codes

    Lee, Kyung Won; Cheong, Aeju; Shin, Andong; Cho, Min Ki [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2016-10-15

    In order to validate the operational performance of the PAFS, KAERI has performed the experimental investigation using the PASCAL (PAFS Condensing heat removal Assessment Loop) facility. In this study, we simulated the KAERI PASCAL SS-540-P1 test with MARS-KS V1.4 and TRACE V5.0 p4 codes to assess the code predictability for the condensation heat transfer inside the passive auxiliary feedwater system. We simulated the KAERI PASCAL SS-540-P1 test with MARS-KS V1.4 and TRACE V5.0 p4 codes to assess the code predictability for the condensation heat transfer inside the passive auxiliary feedwater system. The calculated results of heat flux, inner wall surface temperature of the condensing tube, fluid temperature, and steam mass flow rate are compared with the experimental data. The result shows that the MARS-KS generally under-predict the heat fluxes. The TRACE over-predicts the heat flux at tube inlet region and under-predicts it at tube outlet region. The TRACE prediction shows larger amount of steam condensation by about 3% than the MARS-KS prediction.

  17. Proceedings of 2005 JAEA-KAERI joint seminar on advanced irradiation and PIE technologies

    2006-05-01

    In this seminar, total participants of over 100 were jointed from JAEA, KAERI, Hanyang University, Chungnam National University, Kyung Hee University, Oarai Branch of Institute for Materials Research (IMR) of Tohoku University, Nippon Nuclear Fuel Development Co., Ltd., Nuclear Development Corporation and others. The technical development and experimental data on the irradiation test and PIE were aggressively discussed in this seminar. Contributed presentations were 35 in three sessions; Current status and future program on irradiation test and PIE (10 presentations), Development of irradiation and PIE technologies (15 presentations) and Evaluation of irradiation and PIE data (10 presentations). Development of instrumented capsule technologies for HANARO irradiation, current PIE activities in each hot laboratory of both countries, development of irradiation capsules in JMTR for the Irradiation Assisted Stress Corrosion Cracking (IASCC) study, development of irradiation and PIE techniques for the safety research on the high burnup fuel, utilization plan of JOYO and development of MOX fuel containing americium have been widely noticed as topic items on irradiation and PIE technologies. This proceedings is containing papers presented in the 2005 JAEA-KAERI Joint Seminar. It also indicates the current status of the aggressive information exchange activity on two fields of irradiation test and PIE technologies between JAEA and KAERI under the Arrangement for the Implementation of Cooperative Research Program mentioned above. The 35 of the presented papers are indexed individually. (J.P.N.)

  18. Evaluation of the WIMS (KAERI) - VENTURE code system for peak power prediction of KMRR core using MCNP

    Park, W.S.; Lee, K.M.; Lee, C.S.; Lee, J.T.; Oh, S.K.

    1992-01-01

    In this work, the validity and quantitative uncertainty of WIMS (KAERI) - VENTURE code system for the design and analysis of KMRR core was tried to be inferred using a well known benchmark code, MCNP. WIMS (KAERI) showed an excellent agreement with MCNP code. For three different control rod positions at a simulated core which has a quarter symmetry, total peaking factors and three sub-factors (radial, axial, and local) obtained from VENTURE were compared with those of MCNP. The comparison proved the validity of VENTURE and showed better agreement in the order of radial, axial, and local factors. The uncertainty of WIMS (KAERI) - VENTURE system was inferred using the 2σ band of total peaking obtained by MCNP. The uncertainty of WIMS (KAERI) - VENTURE system were found to be 18.5 % for the operating condition. (author)

  19. Proceedings of the 1st JAEA/KAERI information exchange meeting on HTGR and nuclear hydrogen technology

    Sato, Hiroyuki; Sakaba, Nariaki; Nishihara, Tetsuo; Yan, Xing L.; Hino, Ryutaro

    2007-03-01

    Japan Atomic Energy Agency (JAEA) has completed an implementation with Korea Atomic Energy Research Institute (KAERI) on HTGR and nuclear hydrogen technology, 'The Implementation of Cooperative Program in the Field of Peaceful Uses of Nuclear Energy between KAERI and JAEA. 'To facilitate efficient technology development on HTGR and nuclear hydrogen by the IS process, an information exchange meeting was held at the Oarai Research and Development Center of JAEA on August 28-30, 2006 under Program 13th of the JAEA/KAERI Implementation, 'Development of HTGR and Nuclear Hydrogen Technology'. JAEA and KAERI mutually showed the status and future plan of the HTTR (High-Temperature Engineering Test Reactor) project in Japan and of the NHDD (Nuclear Hydrogen Development and Demonstration) project in Korea, respectively, and discussed collaboration items. This proceedings summarizes all materials of presented technical discussions on HTGR and hydrogen production technology as well as the meeting briefing including collaboration items. (author)

  20. A study for developing training courses of the nuclear training center -with priority given to the training goals of KAERI-

    Kim, Yong; Seo, In Seok; Kim, Deok In; Lee, Won Koo; Lee, Sueng Hee; Lee, Byoung Soen; Lee, Uei Jin; Kim, Young Joong; Oh, Sei Ki; Jeon, Hyong Ryon; Kim, Dong Soo; Lee, Han Young; Lee, Dong Jin

    1993-01-01

    The final goal of this project, which covers 3 years (from 1992 to 1994), is to develop personnel training courses of the Korea Atomic Energy Research Institute (KAERI) and to derive the most desirable training system therefrom. To achieve this final goal successfully the first year's research was designed and has been carried on; firstly, to analyze the on-going issues and what kind of reform measures should be introduced to both the input and conversion processes of KAERI to efficiently achieve the organization goals, secondly, to derive personnel training goals of KAERI based on the analyses. First, this study introduced the viewpoint of systems approach for organization analysis, and defined that the productivity of an organization mainly depends on manpower quality of the input section and efficiency of the conversion process. Next, general organization theories and characteristics of research and development organization were studied, and derived that in research and development organization the expertise of a specialist should be regarded as the main value rather than his position, and the atmosphere should be human-centered, being free and democratic rather than authoritarian. And the study emphasizes more flatted structure of organization, necessity of sense of Management By Objectives (MBO), future planning capability, quality of manager with democratic leadership as criteria for the analysis of research and development organization. Finally, analyzing organization structure and behavior of KAERI based on the criteria, the study derived the ends-means hierarchy of personnel training of KAERI and discussed the necessity of organization reform of KAERI. (Author)

  1. Exposure dose evaluation of worker at radioactive waste incineration facility on KAERI

    Park, Sang Kyu; Jeon, Jong Seon; Kim, Youn Hwa; Lee, Jae Min; Lee, Gi Won

    2011-01-01

    An incineration treatment of inflammable radioactive wastes leads to have a reduction effect of disposal cost and also to contribute an enhancement of safety at a disposal site by taking the advantage of stabilization of the wastes which is accomplished by converting organic materials into inorganic materials. As it was required for an incineration technology, KAERI (Korea Atomic Energy Research Institute) has developed a pilot incineration process and then constructed a demonstration incineration facility having based on the operating experiences of the pilot process. In this study, worker exposure doses were evaluated to confirm safety of workers before the demonstration incineration facility will commence a commercial. (author)

  2. The development of KAERI management information system -First year: The development of manpower information management system-

    Kang, Shin Bok; Huh, Young Hwan; Lee, Jong Bok; Park, Soo Jin; Lee, Young Jae; Park, Yeon Sik; Jang, Deok Kyu; Park, Seung Deok; Kim, Jong Myeong [Korea Atomic Energy Res. Inst., Taejon (Korea, Republic of)

    1991-12-01

    The purpose of this report is to describe the implementation of the management information system for manpower. This job is the first year`s for development KAERI management information system. It is important to properly manage a manpower to cope with the external circumstances promptly and to maximize the productivity of the organization. This report aims at basic management of manpower and uses multimedia to keep abreast with the times and introduces the concept of GUI (Graphic User Interface) to user for ease access. (Author).

  3. The development of KAERI management information system -First year: The development of manpower information management system-

    Kang, Shin Bok; Huh, Young Hwan; Lee, Jong Bok; Park, Soo Jin; Lee, Young Jae; Park, Yeon Sik; Jang, Deok Kyu; Park, Seung Deok; Kim, Jong Myeong

    1991-12-01

    The purpose of this report is to describe the implementation of the management information system for manpower. This job is the first year's for development KAERI management information system. It is important to properly manage a manpower to cope with the external circumstances promptly and to maximize the productivity of the organization. This report aims at basic management of manpower and uses multimedia to keep abreast with the times and introduces the concept of GUI (Graphic User Interface) to user for ease access. (Author)

  4. Upgraded Features of Newly Constructed Fuel Assembly Mechanical Characterization Test Facility in KAERI

    Lee, Kang Hee; Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu; Lee, Young Ho; Kim, Soo Ho; Yang, Jae Ho [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    Fuel assembly mechanical characterization test facility (FAMeCT) in KAERI is newly constructed with upgraded functional features such as increased loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. The facility building is compactly designed in the scale of 3rd floor building and has regions for assembly-wise mechanical test equipment, dynamic load (seismic) simulating test system, small scale hydraulic loop and component wise test equipment. Figure 1 shows schematic regional layout of the facility building. Mechanical test platform and system is designed to increase loading capacity for axial compression test. Structural stability of the support system of new upper core plate simulator is validated through a limit case functional test. Fuel assembly mechanical characterization test facility in KAERI is newly constructed and upgraded with advanced functional features such as uprated loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. This paper briefly introduce the test facility construction and scope of the facility and is focused on the upgraded design features of the facility. Authors hope to facilitate the facility more in the future and collaborate with the industry.

  5. Study on the Enhancement of Nuclear Control and Emergency Preparedness Systems in KAERI

    So, Dong Sup; Lee, T. Y.; Lee, B. D.; Yoo, J. G.; Lee, G. Y.; Lee, S. H.; Kim, H. J.; Kim, H. S.; Park, H. J

    2006-12-15

    The purposes of the study are: to implement obligations specified in treaties and domestic laws and to enhance the nuclear transparency suffered from a careless experiment, being issued in 2004, with nuclear material; and to prepare nuclear emergency and to settle down effectively the emergency situation. We established an infrastructure of the system of accounting for and control of nuclear material. and installed systematic measures to deal the cases of radiation accidents. In the first year (2006) the project is focused on the development of two systems: an information treatment system that controls and manages the nuclear material in facilities at KAERI; and a real-time surveillance system that integrates the safety system information of nuclear facilities in KAERI. The development of information treatment system for IAEA safeguards and facility-level accountancy has been initiated in October, 2006, and planned to complete by October 2007. Communication channels between the emergency control head-quarter and the briefing rooms of facilities and accident areas are established to implement an advanced supervision system for radiation accidents. Also, a surveillance system, that collects and supervises the facilities' safety system parameters in real time, is installed and confirmed that the display system of the safety parameters is stably operating.

  6. Studying the processes of sodium-water interaction in the BOR-60 reactor micromodule steam generator

    Tsykanov, V.A.; Antipin, G.K.; Borisov, V.V.

    1981-01-01

    Main results of experimental studies of emergency regimes of micromodule steam generator (MSG) at small and big leaks of water into sodium, realized using the 30 MW MSG, operating in the BOR-o0 reactor, are considered. The aims of the study are as follows: the modelling of macroleak in ''Nadja'' steam generator for the BN-350 reactor; testing the conceptions of alarm signalling and MSG protection; testing under real conditions of new perspective systems of leak detection; gaining the experimence and development of the ways to eliminate the consequences of accident caused by big water leak into sodium; accumulation of knowledge on restoration of MSG operating ability after accident; experimental test of calculational techniques for big leak accidents to use them in future for calculational studies of similar situations at other reactors equipped with sodium-water steam generators; refinement of characteristics of hydrodynamic and thermal effects interaction zone for big leak in real circuit during the plant operation. A series of experiments with the imitation of water leak into sodium by means of argon and steam supply through injection devices, located before the steam superheater module of one of the sections and between evaporator module of the same section, is conducted. The range of steam flow rate is 0.02-0.45 g/s. Duration of steam supply is 100-400 s. A conclusion is made that the results obtained can be used for steam generator of the BN-350 reactor [ru

  7. A study for developing training courses of the nuclear training center -with priority given to the training goals of KAERI-

    Kim, Yong; Seo, In Seok; Kim, Deok In; Lee, Won Koo; Lee, Sueng Hee; Lee, Byoung Soen; Lee, Uei Jin; Kim, Young Joong; Oh, Sei Ki; Jeon, Hyong Ryon; Kim, Dong Soo; Lee, Han Young; Lee, Dong Jin [Korea Atomic Energy Res. Inst., Taejon (Korea, Republic of)

    1993-01-01

    The final goal of this project, which covers 3 years (from 1992 to 1994), is to develop personnel training courses of the Korea Atomic Energy Research Institute (KAERI) and to derive the most desirable training system therefrom. To achieve this final goal successfully the first year`s research was designed and has been carried on; firstly, to analyze the on-going issues and what kind of reform measures should be introduced to both the input and conversion processes of KAERI to efficiently achieve the organization goals, secondly, to derive personnel training goals of KAERI based on the analyses. First, this study introduced the viewpoint of systems approach for organization analysis, and defined that the productivity of an organization mainly depends on manpower quality of the input section and efficiency of the conversion process. Next, general organization theories and characteristics of research and development organization were studied, and derived that in research and development organization the expertise of a specialist should be regarded as the main value rather than his position, and the atmosphere should be human-centered, being free and democratic rather than authoritarian. And the study emphasizes more flatted structure of organization, necessity of sense of Management By Objectives (MBO), future planning capability, quality of manager with democratic leadership as criteria for the analysis of research and development organization. Finally, analyzing organization structure and behavior of KAERI based on the criteria, the study derived the ends-means hierarchy of personnel training of KAERI and discussed the necessity of organization reform of KAERI. (Author).

  8. Reaction

    abp

    19 oct. 2017 ... Reaction to Mohamed Said Nakhli et al. concerning the article: "When the axillary block remains the only alternative in a 5 year old child". .... Bertini L1, Savoia G, De Nicola A, Ivani G, Gravino E, Albani A et al ... 2010;7(2):101-.

  9. R and D activities on the management of waste chloride salts in KAERI

    In-Tae, Kim; Hwan-Seo, Park; Jeong-Gook, Kim; Hee-Chul, Yang; Yong-Joon, Cho; Eung-Ho Kim

    2007-01-01

    Full text of publication follows. Electrochemical treatment of spent oxide fuels has been intensively studied in KAERI to reduce the volume, heat load and radiotoxicity of high-level wastes. It consists of an electrolytic reduction process to convert the oxide fuel into a metallic form and an electro-refining process to separate TRU elements from the electro-reduced metal ingot. Two types of waste salts are expected to generate from the electrochemical pyro-processes, that is, LiCl salt from the reduction process and LiCl+KCl eutectic salt form the refining process. The R and D strategy of the waste salt management in KAERI can be categorized into two parts: 1) enhancement of safety by the stabilisation/solidification of waste salt that is to be finally disposed of and 2) reduction of the waste generation by the regeneration/recycle of the spent salt after removal of radionuclides in it. A sol-gel technique and a zeolite occlusion technique are under development to stabilize the waste salt. The LiCl salt is stabilised by a low-temperature sol-gel process and then the gel product is solidified into a ceramic-like waste form with an addition of glass frit. Another method uses Zeolite-4A to occlude the LiCl salt into its cage and adsorption site to immobilize the radionuclides. The product, salt-occluded zeolite, is fabricated into another type of a ceramic waste form. For the regeneration and recycle of the spent salt, the radionuclides in the salt are removed by a zeolite process for the LiCl salt and by an oxidation/distillation process for the eutectic salt. The target nuclides to be removed in each process are Cs/Sr and rare earth (RE) elements, respectively. In the oxidation/ distillation process, the rare earth chloride nuclides are oxidised by an oxygen sparging method, and the products are precipitated in the form of oxide or oxychloride REs. After separation of the RE elements from the precipitates by distillation, the refined spent salt with a low content

  10. Study on sodium water glass-based anti-reflective film and its application in dye-sensitized solar cells

    Huang, Q.Z. [Key Laboratory of Renewable Energy, Guangdong Key Laboratory of New and Renewable Energy Research and Development, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Shi, J.F., E-mail: shijf@ms.giec.ac.cn [Key Laboratory of Renewable Energy, Guangdong Key Laboratory of New and Renewable Energy Research and Development, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510000 (China); Wang, L.L.; Li, Y.J.; Zhong, L.W. [Key Laboratory of Renewable Energy, Guangdong Key Laboratory of New and Renewable Energy Research and Development, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510000 (China); Xu, G., E-mail: xugang@ms.giec.ac.cn [Key Laboratory of Renewable Energy, Guangdong Key Laboratory of New and Renewable Energy Research and Development, Guangzhou Institute of Energy Conversion, Chinese Academy of Sciences, Guangzhou 510000 (China)

    2016-07-01

    In this paper, anti-reflective (AR) films are prepared from sodium water glass with a simple dip-coating method. The effects of SiO{sub 2}/Na{sub 2}O molar ratio, concentration of water glass, and withdrawal speed on the anti-reflection performance of the AR films are systematically studied. The optimized AR film is further applied in dye-sensitized solar cells (DSCs). The optical properties and surface morphology of AR films are analyzed by ultraviolet-visible spectrophotometer, scanning electron microscope, and atomic force microscope. Transmittance of the glass coated with sodium water glass-based AR film is increased by 3.2% when the SiO{sub 2}/Na{sub 2}O molar ratio, concentration, and withdrawal speed equal to 3.8, 5 wt%, and 80 mm/min, respectively. Under this condition, the thickness of the AR film is 127 nm and the AR film has obvious porous structure. In addition, the power conversion efficiency of DSC coated by AR film is increased from 7.92% to 8.24%, compared with the DSC without AR film. - Highlights: • Anti-reflective films are prepared from sodium water glass. • Transmittance of anti-reflective film is increased by 3.2%. • Efficiency of dye-sensitized cell is improved by anti-reflective film.

  11. Study on sodium water glass-based anti-reflective film and its application in dye-sensitized solar cells

    Huang, Q.Z.; Shi, J.F.; Wang, L.L.; Li, Y.J.; Zhong, L.W.; Xu, G.

    2016-01-01

    In this paper, anti-reflective (AR) films are prepared from sodium water glass with a simple dip-coating method. The effects of SiO_2/Na_2O molar ratio, concentration of water glass, and withdrawal speed on the anti-reflection performance of the AR films are systematically studied. The optimized AR film is further applied in dye-sensitized solar cells (DSCs). The optical properties and surface morphology of AR films are analyzed by ultraviolet-visible spectrophotometer, scanning electron microscope, and atomic force microscope. Transmittance of the glass coated with sodium water glass-based AR film is increased by 3.2% when the SiO_2/Na_2O molar ratio, concentration, and withdrawal speed equal to 3.8, 5 wt%, and 80 mm/min, respectively. Under this condition, the thickness of the AR film is 127 nm and the AR film has obvious porous structure. In addition, the power conversion efficiency of DSC coated by AR film is increased from 7.92% to 8.24%, compared with the DSC without AR film. - Highlights: • Anti-reflective films are prepared from sodium water glass. • Transmittance of anti-reflective film is increased by 3.2%. • Efficiency of dye-sensitized cell is improved by anti-reflective film.

  12. Joint KAERI/VAEC pre-possibility study on a new research reactor for Vietnam

    Park, Cheol; Lee, B. C.; Chae, H. T.; Kim, H.; Lee, C. S.; Choi, C. O.; Jun, B. J. [KAERI, Taejon (Korea, Republic of); Vien, Luong Ba; Dien, Nguyen Nhi [Vietnam Atomic Energy Commission, Hanoi (Viet Nam)

    2004-05-01

    Based on the agreement on the technical cooperation for nuclear technology between Korea and Vietnam, a KAERI/VAEC joint study on the pre-possibility of a new research reactor for Vietnam has been carried out in the research reactor area from Nov. 2003 to May 2004. In this report, the results of the pre-possibility study on a new research reactor are described. The report presents the necessity of a new research reactor in Vietnam, and the desired performance requirements of the new research reactor if necessary. The major design characteristics of some existing research reactors and those under planning were also reviewed and the main characteristics which should be considered in selecting a new multipurpose research reactor for Vietnam were drawn. Some recommendations on the considerations for the next step of the feasibility study such as the project formulation, manpower requirements and international co-operation were also briefly touched upon.

  13. Development of 14.5 GHz electron cyclotron resonance ion source at KAERI

    Byung-Hoon, Oh; Sang-Ryul, In; Kwang-Won, Lee; Chang Seog, Seo; Jung-Tae, Jin; Dae-Sik, Chang; Seong Ho, Jeong; Chul-Kew Hwang

    2012-01-01

    A 14.5 GHz ECRIS has been designed and fabricated at KAERI (Korea Atomic Energy Research Institute) to produce multi-charged ion beam (especially for C 6+ ion beam) for medical application. The magnet system has copper conductor solenoid coils and a permanent magnet hexapole. A welded tube with aluminium and stainless steel is used for an ECR plasma chamber to improve the production of secondary electron. A klystron supplies microwave energy to the plasma. A movable beam extractor with 8 mm aperture covers different species and different charge numbers of the beam. Fabrication and initial experimental results on ECR plasma are discussed in this paper. The paper is followed by the slides of the presentation. (authors)

  14. Joint KAERI/VAEC pre-possibility study on a new research reactor for Vietnam

    Park, Cheol; Lee, B. C.; Chae, H. T.; Kim, H.; Lee, C. S.; Choi, C. O.; Jun, B. J.; Vien, Luong Ba; Dien, Nguyen Nhi

    2004-05-01

    Based on the agreement on the technical cooperation for nuclear technology between Korea and Vietnam, a KAERI/VAEC joint study on the pre-possibility of a new research reactor for Vietnam has been carried out in the research reactor area from Nov. 2003 to May 2004. In this report, the results of the pre-possibility study on a new research reactor are described. The report presents the necessity of a new research reactor in Vietnam, and the desired performance requirements of the new research reactor if necessary. The major design characteristics of some existing research reactors and those under planning were also reviewed and the main characteristics which should be considered in selecting a new multipurpose research reactor for Vietnam were drawn. Some recommendations on the considerations for the next step of the feasibility study such as the project formulation, manpower requirements and international co-operation were also briefly touched upon

  15. A Study on the Management of Intellectual Property for the Potential Markets of KAERI

    Chung, Whansam; Yun, S. W.; Lee, D. S.; Yoo, Y. H.; Hong, S. W.

    2012-12-15

    The intellectual property law of the Republic of South Africa is similar to that of Korea except for a few regulations. In Republic of South Africa, the rights of joint inventor are limited, there is no request for examination, and the allowance of patent is generally determined within 18 months from the application date. Risky patents or applications are not found in Republic of South Africa. However, KAERI needs ceaselessly to search and investigate patents or patent applications in Republic of South Africa. Finally, we propose to build a patent management team within an operation division to respond swiftly to possible market changes. The operation-oriented patent management team will efficiently secure competitive patents and effectively realize a profit from the competitive patents.

  16. A Study on the Management of Intellectual Property for the Potential Markets of KAERI

    Chung, Whansam; Yun, S. W.; Lee, D. S.; Yoo, Y. H.; Hong, S. W.

    2012-12-01

    The intellectual property law of the Republic of South Africa is similar to that of Korea except for a few regulations. In Republic of South Africa, the rights of joint inventor are limited, there is no request for examination, and the allowance of patent is generally determined within 18 months from the application date. Risky patents or applications are not found in Republic of South Africa. However, KAERI needs ceaselessly to search and investigate patents or patent applications in Republic of South Africa. Finally, we propose to build a patent management team within an operation division to respond swiftly to possible market changes. The operation-oriented patent management team will efficiently secure competitive patents and effectively realize a profit from the competitive patents

  17. Preliminary Study of Feasibility of Acoustic Detection of Small Sodium-Water Reactions in Lmfbr Steam Generators.

    Chamberlain, H. V.

    1970-06-01

    An evaluation of acoustic techniques for the detection of sound resulting from water leaks into liquid sodium was conducted. Acoustic spectra over the range of 100Hz to 80kHz were detected. A leak as small as 0.00008 lb/ sec was detected by the acoustic instrumentation. The indicated leak rate was the smallest that was injected into the liquid sodium, and is not to be interpreted as the smallest leak rate that might be detected by the acoustic method. Detection time was found to be essentially instantaneous.

  18. Mapping Fractures in KAERI Underground Research Tunnel using Ground Penetrating Radar

    Baek, Seung-Ho; Kim, Seung-Sep; Kwon, Jang-Soon

    2016-04-01

    The proportion of nuclear power in the Republic of Korea occupies about 40 percent of the entire electricity production. Processing or disposing nuclear wastes, however, remains one of biggest social issues. Although low- and intermediate-level nuclear wastes are stored temporarily inside nuclear power plants, these temporary storages can last only up to 2020. Among various proposed methods for nuclear waste disposal, a long-term storage using geologic disposal facilities appears to be most highly feasible. Geological disposal of nuclear wastes requires a nuclear waste repository situated deep within a stable geologic environment. However, the presence of small-scale fractures in bedrocks can cause serious damage to durability of such disposal facilities because fractures can become efficient pathways for underground waters and radioactive wastes. Thus, it is important to find and characterize multi-scale fractures in bedrocks hosting geologic disposal facilities. In this study, we aim to map small-scale fractures inside the KAERI Underground Research Tunnel (KURT) using ground penetrating radar (GPR). The KURT is situated in the Korea Atomic Energy Research Institute (KAERI). The survey target is a section of wall cut by a diamond grinder, which preserves diverse geologic features such as dykes. We conducted grid surveys on the wall using 500 MHz and 1000 MHz pulseEKKO PRO sensors. The observed GPR signals in both frequencies show strong reflections, which are consistent to form sloping planes. We interpret such planar features as fractures present in the wall. Such fractures were also mapped visually during the development of the KURT. We confirmed their continuity into the wall from the 3D GPR images. In addition, the spatial distribution and connectivity of these fractures are identified from 3D subsurface images. Thus, we can utilize GPR to detect multi-scale fractures in bedrocks, during and after developing underground disposal facilities. This study was

  19. On the method of heat exchange calculation for critical and postcritical regimes in sodium-water steam generators

    Khudasko, V.V.; Kardash, D.Yu.; Grachev, N.S.

    1986-01-01

    Technique for calculating heat exchange in sodium-water steam generators with provisions for steam-water flow non-equilibrium character and moisture additional evaporation in pipes is suggested. Zone of heat exchange crisis representing the zone of transition from developed boiling to postcritical zone is considered. Comparison of estimated and experimental data performed for the following ranges of steame generator parameters: pressure p=7.8-14.0 MPa, coolant flow rate ρw=350-1000 kg/(m 2 xs), inlet sodium temperature T=590-825 K shows their good agreement

  20. RANS based CFD methodology for a real scale 217-pin wire-wrapped fuel assembly of KAERI PGSFR

    Jeong, Jae-Ho, E-mail: jhjeong@kaeri.re.kr [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseoung-gu, Daejeon (Korea, Republic of); Song, Min-Seop [Department of Nuclear Engineering, Seoul National University, 559 Gwanak-ro, Gwanak-gu, Seoul (Korea, Republic of); Lee, Kwi-Lim [Korea Atomic Energy Research Institute, 989-111 Daedeok-daero, Yuseoung-gu, Daejeon (Korea, Republic of)

    2017-03-15

    Highlights: • This paper presents a suitable way for a practical RANS based CFD methodology which is applicable to real scale 217-pin wire-wrapped fuel assembly of KAERI PGSFR. • A key point of differentiation of the RANS based CFD methodology in this study is adapting an innovative grid generation method using a fortran based in-house code with a GGI function in a general-purpose commercial CFD code, CFX. • The RANS based CFD methodology is implemented with high resolution scheme and SST turbulence model in the 7-pin 37-pin, and 127-pin wire-wrapped fuel assembly of PNC and JNC. Furthermore, the RANS based CFD methodology can be successfully extended to the real scale 217-pin wire-wrapped fuel bundles of KAERI PGSFR. • Three-dimensional thermal-hydraulic characteristics have been also investigated briefly. - Abstract: This paper presents a suitable way for a practical RANS (Reynolds Averaged Navier-Stokes simulation) based CFD (Computational Fluid Dynamics) methodology which is applicable to real scale 217-pin wire-wrapped fuel assembly of KAERI (Korea Atomic Energy Research Institute) PGSFR (Prototype Gen-IV Sodium-cooled Fast Reactor). The main purpose of the current study is to support license issue for the KAERI PGSFR core safety and to elucidate thermal-hydraulic characteristics in a 217-pin wire-wrapped fuel assembly of KAERI PGSFR. A key point of differentiation of the RANS based CFD methodology in this study is adapting an innovative grid generation method using a fortran based in-house code with a GGI (General Grid Interface) function in a general-purpose commercial CFD code, CFX. The innovative grid generation method with GGI function can achieve to simulate a real wire shape with minimizing cell skewness. The RANS based CFD methodology is implemented with high resolution scheme in convection term and SST (Shear Stress Transport) turbulence model in the 7-pin 37-pin, and 127-pin wire-wrapped fuel assembly of PNC (Power reactor and Nuclear fuel

  1. First lasing of the KAERI millimeter-wave free electron laser

    Lee, B.C.; Jeong, Y.U.; Cho, S.O. [Korea Atomic Energy Research Institute, Taejon (Korea, Democratic People`s Republic of)] [and others

    1995-12-31

    The millimeter-wave FEL program at KAERI aims at the generation of high-power CW laser beam with high efficiency at the wavelength of 3{approximately}10 mm for the application in plasma heating and in power beaming. In the first oscillation experiment, the FEL has lased at the wavelength of 10 mm with the pulsewidth of 10{approximately}30 {mu}s. The peak power is about 1 kW The FEL is driven by a recirculating electrostatic accelerator having tandem geometry. The energy and the current of the electron beam are 400 keV and 2 A, respectively. The FEL resonator is located in the high-voltage terminal and is composed of a helical undulator, two mesh mirrors, and a cylindrical waveguide. The parameters of the permanent-magnet helical undulator are : period = 32 mm, number of periods = 20, magnetic field = 1.3 kG. At present, with no axial guiding magnetic field only 15 % of the injected beam pass through the undulator. Transport ratio of the electron beam through the undulator is very sensitive to the injection parameters such as the diameter and the divergence of the electron beam Simulations show that, with unproved injection condition, the FEL can generate more than 50 kW of average power in CW operation. Details of the experiments, including the spectrum measurement and the recirculation of electron beam, are presented.

  2. Current status of ACE format libraries for MCNP at nuclear date center of KAERI

    Kim, Do Heon; Gil, Choong Sup; Lee, Young Ouk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-09-15

    The current status of ACE format MCNP/MCNPX libraries by NDC of KAERI is presented with a short description of each library. Validation calculations with recent nuclear data evaluations ENDF/B-VII.0, ENDF/B-VII.1, JEFF-3.2, and JENDL-4.0 have been carried out by the MCNP5 code for 119 criticality benchmark problems taken from the expanded criticality validation suite supplied by LANL. The overall performances of the ACE format KN-libraries have been analyzed in comparison with the results calculated with the ENDF/B-VII.0-based ENDF70 library of LANL. It was confirmed that the ENDF/B-VII.1-based KNE71 library showed better performances than the others by comparing the RMS errors and χ2 values for five benchmark categories as well as whole benchmark problems. ENDF/B-VII.1 and JEFF-3.2 have a tendency to yield more reliable MCNP calculation results within certain confidence intervals regarding the total uncertainties for the keff values. It is found that the adoption of the latest evaluated nuclear data might ensure better outcomes in various research and development areas.

  3. Mechanical Property and Oxidation Behavior of ATF cladding developed in KAERI

    Kim, Hyun-Gil; Kim, Il-Hyun; Jung, Yang-Il; Park, Dong-Jun; Park, Jung-Hwan; Park, Jeong-Yong; Koo, Yang-Hyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    To realize the coating cladding, coating material (Cr-based alloy) as well as coating technology (3D laser coating and arc ion plating combined with vacuum annealing) can be developed to meet the fuel cladding criteria. The coated Zr cladding can be produced after the optimization of coating technologies. The coated cladding sample showed the good oxidation/corrosion and adhesion properties without the spalling and/or severe interaction with the Zr alloy cladding from the various tests. Thus, it is known that the mechanical property and oxidation behavior of coated cladding concept developed in KAERI is reasonable for applying the ATF cladding in LWRs. At the present time various ATF concepts have been proposed and developing in many countries. The ATF concepts with potentially improved accident performance can be summarized to the coating cladding, Mo-Zr cladding, FeCrAl cladding, and SiCf/SiC cladding. Regarding the cladding performance, ATF cladding concepts will be evaluated with respect to the accident scenarios and normal operations of LWRs as well as to the fuel cladding fabrication.

  4. The KAERI laser facility with temporal laser beam shaping for application's user

    Hong, Sung Ki; Kim, Min Suk; Kim, Young Won; Ko, Kwanghoon; Lim, Changhwan; Seo, Young Seok

    2008-01-01

    The Korea Atomic Energy Research Institute(KAERI)has been developed a high energy Nd:Glass laser facility(KLF)for fast ignition research and high energy physics applications at early 2008. Now, we are researching the temporal laser beam shaping for application's user. The temporal laser beam shaping has been applied to a number of industrial applications. The KLF beam shaping system with fiber based consists of two electro optic modulator with DC bias using a Mach Zehnder interferometer, an arbitrary electronic waveform generator, a continuous wavelength fiber laser source, a fiber based pulse amplification system and DC bias source to generate temporally shaped pulses with a high extinction ratio and high resolution. RF signal waveform user defined by an arbitrary electronic waveform generator is only connected to one electro optic modulator. DC bias source with auto feed back or manual controller is connected both two electro optic modulators. Emitting laser light from a continuous wavelength fiber laser source is modulated to meet a user defined laser pulse with a high extinction ratio by two electro optic modulators. Experimental results are shown in Fig.1. Figure 1(a)shows two programmed waveforms with the signal width 10ns in an arbitrary electronic waveform generator. Figure 1(b)shows output laser pulses with sub mJ energy from amplification results of the KLF beam shaping system which can control the pulse width ranges from 400ps to sub us

  5. Investigation for the Fossil Embryo using Neutron Tomography at HANARO, KAERI

    Kim, Tae Joo; Sim, Cheul Muu; Kim, Dong Hee; Grellet-Tinner, Gerald

    2012-01-01

    Neutron imaging technique is one of non-destructive method. It is similar to X-ray and g-ray methods in using the different attenuation characteristics depending on materials. However, there is great difference between them. The mass attenuation coefficients of X-ray and g- ray monotonically increase with the atomic number since they interact with electrons. Thus X-ray image method does not supply sufficient contrast between similar atomic numbers. On the other hand, that of thermal neutrons depends much on the nucleus not electrons. Especially thermal neutrons easily penetrate most of metals, while they are attenuated well by such materials as hydrogen, water, boron, gadolinium and cadmium. Because of these unique characteristics of neutron, neutron imaging technique has been utilized for NDT or researches for next power sources (fuel cell or Li-Ion battery). Recently, dinosaur egg was found at the Aptian. Albian Algui Ulaan Tsav site, Mongolia. In this study, we applied the neutron imaging technique to investigate dinosaur embryo at Neutron Radiography Facility of HANARO, KAERI

  6. SNU-KAERI Degree and Research Center for Radiation Convergence Sciences

    Jo, Sungkee; Kim, S. U.; Roh, C. H

    2011-12-01

    In this study, we tried to establish and perform the demonstrative operation of the 'Degree and Research Center for Radiation Convergence Sciences' to raise the Korea's technology competitiveness. As results of this project we got the successful accomplishment as below: 1. Operation of Degree and Research Center for Radiation Convergence Sciences and establishment of expert researcher training system Ο Presentation of an efficient model for expert researcher training program through the operation of university-institute collaboration courses by combining of Graduate course and DRC system. Ο Radiation Convergence Sciences major is scheduled to be established in 2013 at SNU Graduate School of Convergence Science and Technology Ο A big project for research, education, and training of radiation convergence science is under planning 2. Establishment and conduction of joint research by organization of radiation convergence research consortium · Joint research was conducted in close connection with the research projects of researchers participating in this DRC project (44 articles published in journals, 6 patents applied, 88 papers presented in conferences) · The resources of the two organization (SNU and KAERI), such as research infrastructure (hightech equipment and etc), manpower (professor/researcher), and original technology and know how were utilized to conduct the joint research and to establish the collaboration system of the two organizations

  7. Cultivation of university students in radiology using research facilities at KAERI

    Shin, Byung Chul [Nuclear Training and Education Center, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-09-15

    The purpose of present research is to offer a specialized educational opportunity for potential users, university students in radiology, by developing specific curriculum on site at KAERI, using HANARO research reactor and National radiation research facilities. The specific items of this research accomplished are: First, Development and operation of various curricula for specific research using HANARO and National radiation research facilities to provide university students with opportunities to use the facilities. Second, Operation of the experiment training programs for university students in radiology to foster next generation specialists. Third, through the on-site experiment training for students in radiology, support future potential experts of the radiation research fields, and broaden the base. A textbook and a teaching aid, a questionnaire have been developed to support the program. 714 university students have completed the courses for radiology experiment from 2006 to 2017. It is hoped that these experiments broaden public awareness and acceptance by the present and potential future utilization of the research reactor and national radiation research facilities, thereby bring positive impacts to policy making.

  8. Investigation for the Fossil Embryo using Neutron Tomography at HANARO, KAERI

    Kim, Tae Joo; Sim, Cheul Muu [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Dong Hee [National Science Museum, Daejeon (Korea, Republic of); Grellet-Tinner, Gerald [The Field Museum, Chicago (United States)

    2012-05-15

    Neutron imaging technique is one of non-destructive method. It is similar to X-ray and g-ray methods in using the different attenuation characteristics depending on materials. However, there is great difference between them. The mass attenuation coefficients of X-ray and g- ray monotonically increase with the atomic number since they interact with electrons. Thus X-ray image method does not supply sufficient contrast between similar atomic numbers. On the other hand, that of thermal neutrons depends much on the nucleus not electrons. Especially thermal neutrons easily penetrate most of metals, while they are attenuated well by such materials as hydrogen, water, boron, gadolinium and cadmium. Because of these unique characteristics of neutron, neutron imaging technique has been utilized for NDT or researches for next power sources (fuel cell or Li-Ion battery). Recently, dinosaur egg was found at the Aptian. Albian Algui Ulaan Tsav site, Mongolia. In this study, we applied the neutron imaging technique to investigate dinosaur embryo at Neutron Radiography Facility of HANARO, KAERI

  9. A Study of the pre-retirement program implementation for KAERI nuclear experts

    Hong, Hyo-Jeong; Hwang, Hye-Seon; Nam, Young-Mi; Jin, You-Rim; Song, Eun-Ju

    2017-01-01

    people in Korea take far more of interests in the nuclear power and whether they are well prepared in the lack of professional human resources in it in the foreseeable future. It is not only personal concern anymore, but also national concern. In particular, retirement of the experts in nuclear field is likely to lose our competitiveness in the world. It is urgent for the government and institutions in Korea to develop and implement educational programs to secure talented new workers in the field. This study analyzes the cases of development and application of pre-retirement education program of professional talent for nuclear R and D and then, develops programs to help nuclear experts retire. In the aging society, the retirement of nuclear experts is a national issue that can't be held off rather than each worker's problem. There are people at the heart of nuclear power. This is because they do all the things like nuclear research and development, and construction. Therefore, it is important to nurture and manage nuclear experts to ensure the sustainable development of nuclear with safety. This program could be also a part of it. KAERI is the organization that represents domestic nuclear research, and it is their urgent task to prepare for aging.

  10. R and D strategy on remote response technology for emergency situations of nuclear facilities in KAERI

    Jeong, Kyung Min; Cho, Jae Wan; Choi, Young Soo; Eom, Heung Seup; Seo, Yong Chil; Shin, Hoch Ul; Lee, Sung Uk; Kim, Chang Hoi; Jeong, Seung Ho; Kim, Seung Ho

    2012-01-01

    it to scour surfaces, scoop samples and vacuum sludge. To perform cleanup tasks, they built Workhorse that featured system redundancy and had a boom extend able to reach high places, but it was never used because it had too many complexities and to clean and fix. While remote robotics technology has proven to remove the human from the radioactive environment, it is also difficult to make it useful because it may requires skill about remote control and obtaining remote situation awareness regardless of the actual task. The efficiency of the human robot interaction is very important to obtain the overall goal for the emergency response in timely manner. It would be a bottle neck to apply the robotic technology for carrying the emergency response in NPP. Simple remote operation schemes are not adequate, more intelligent autonomous operation schemes are required to enhance the effectiveness of robots for the emergency response. KAERI has been developing various robotic systems for nuclear power plants over than 20 years after the Chernobyl accident. But the majority of the developed robotic systems is for the inspection and maintenance of nuclear power plants during their outage periods. Based on the lessons learned from the Fukushima accident, KAERI has planned R and D projects for developing remote response technologies really applicable in emergency situations of nuclear facilities. This paper presents the R and D strategy to achieve real usability and the purpose and research activity plans of on going three projects derived from the strategy

  11. R and D strategy on remote response technology for emergency situations of nuclear facilities in KAERI

    Jeong, Kyung Min; Cho, Jae Wan; Choi, Young Soo; Eom, Heung Seup; Seo, Yong Chil; Shin, Hoch Ul; Lee, Sung Uk; Kim, Chang Hoi; Jeong, Seung Ho; Kim, Seung Ho [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    equipped with various tools allowing it to scour surfaces, scoop samples and vacuum sludge. To perform cleanup tasks, they built Workhorse that featured system redundancy and had a boom extend able to reach high places, but it was never used because it had too many complexities and to clean and fix. While remote robotics technology has proven to remove the human from the radioactive environment, it is also difficult to make it useful because it may requires skill about remote control and obtaining remote situation awareness regardless of the actual task. The efficiency of the human robot interaction is very important to obtain the overall goal for the emergency response in timely manner. It would be a bottle neck to apply the robotic technology for carrying the emergency response in NPP. Simple remote operation schemes are not adequate, more intelligent autonomous operation schemes are required to enhance the effectiveness of robots for the emergency response. KAERI has been developing various robotic systems for nuclear power plants over than 20 years after the Chernobyl accident. But the majority of the developed robotic systems is for the inspection and maintenance of nuclear power plants during their outage periods. Based on the lessons learned from the Fukushima accident, KAERI has planned R and D projects for developing remote response technologies really applicable in emergency situations of nuclear facilities. This paper presents the R and D strategy to achieve real usability and the purpose and research activity plans of on going three projects derived from the strategy.

  12. Development of a web-based sorption database (KAERI-SDB) and application to the safety assessment of a radioactive waste disposal

    Lee, Jae-Kwang; Baik, Min-Hoon; Choi, Jong-Won; Seo, Min-Seok

    2011-01-01

    Sorption plays a key role in a retardation of radionuclide migration in various geological environments. Hence sorption of radionuclides onto geological media is one of the important factors for the safety assessment of radioactive waste disposal. A web-based radionuclide sorption database program named KAERI-SDB has been developed to provide a database for the sorption of radionuclides onto geological media at various geochemical conditions. The KAERI-SDB is designed to determine the distribution coefficient (K d ) of a radionuclide and evaluate sorption properties by easily accessing an internet web-site ( (http://sdb.kaeri.re.kr)). The KAERI-SDB provides a useful output and search result as a scatter plot chart or an index chart. The KAEI-SDB was designed to show the search results in a statistical way by representing the mean K d value at 95% of confidence as a function of major geochemical indices. Several case studies were carried out to demonstrate the applicability of the KAERI-SDB and the result showed a successful applicability of the KAERI-SDB to various radionuclide sorption cases.

  13. Recent Research Status on the Microbes in the Radioactive Waste Disposal and Identification of Aerobic Microbes in a Groundwater Sampled from the KAERI Underground Research Tunnel(KURT)

    Baik, Min Hoon; Lee, Seung Yeop; Cho, Won Jin

    2006-11-01

    In this report, a comprehensive review on the research results and status for the various effects of microbes in the radioactive waste disposal including definition and classification of microbes, and researches related with the waste containers, engineered barriers, natural barriers, natural analogue studies, and radionuclide migration and retardation. Cultivation, isolation, and classification of aerobic microbes found in a groundwater sampled from the KAERI Underground Research Tunnel (KURT) located in the KAERI site have carried out and over 20 microbes were found to be present in the groundwater. Microbial identification by a 16S rDNA genetic analysis of the selected major 10 aerobic microbes was performed and the identified microbes were characterized

  14. An isotope-aided study on the interaction between surface water and groundwater in the KAERI area

    Ahn, Jong Sung; Kim, Jong Hoon; Yun, Si Tae; Jeong, Chan Ho; Kim, Kae Nam

    1988-01-01

    The basement rocks of the KAERI area are compose421d of two mica granite and schistose granite. The groundwater in these fresh crystalline rocks appears to be restricted within the zones developing the fractures. The groundwater in this area occurs mainly in the weathered zones of granitic rocks, with a thickness of 5-20 m. On the results of environmental isotopes analyses, it was proved that surface water and precipitation infiltrated rapidly through the subsurface media into the weathered zone. The high environmental isotopes level found in some groundwater samples are ascribed to the impermeable layer such as clay and silt around the sampling points. Consequently, the groundwater flow in this area is controlled by the heterogeneity of weathered materials. The water types classified by the piper diagram are attributed to the Ca-Cl and Ca-HCO 3 types

  15. Investigation of the development and the effect of an excavation damaged zone at KAERI underground research tunnel

    Kwon, S.; Cho, W. J

    2008-01-15

    The understanding of the long term behavior of rock around an underground radioactive waste repository is essential for the safe design and operation of the repository and for assuring the safety and technical feasibility of geological disposal concept. The investigation of the influence of EDZ on rock mass behavior is important for the long term stability, economy, and safety points of view. In the case of underground repository, which requires high level safety criteria, the accurate prediction of the long and short term mechanical, hydraulic, and thermal behaviors is especially important. In this study, the size and characteristics of EDZ developed during the construction of the KAERI underground research tunnel, which was constructed by controlled blasting, were investigated using various methods. Goodman jack test for measuring deformation modulus, Georadar, rock core observation, MPBX, and stressmeter were carried out at KURT. The rock cores from the boreholes were tested in laboratory for estimating the EDZ size. Empirical and theoretical equations were also used for the prediction of EDZ. The results from laboratory and in situ tests were used in three-dimensional hydro-mechanical and thermo-mechanical analysis for the evaluation of the EDZ effect. The understanding of EDZ size and the property changes in EDZ from in situ and laboratory tests will be used for the planning, design, and analysis of in situ experiments in KURT. The results from the EDZ study will be helpful for the system design as well as safety analysis of a radioactive repository.

  16. A study on implementation plan of decontamination and decommissioning R and D and evaluation of KAERI soil decontamination process

    Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. H.; Choi, W. K.; Kim, G. N.

    2001-08-01

    A. Decontamination Technology Development of Uranium Conversion Facility. Understanding of uranium conversion facility and related decontamination technologies, and analysis of current status of decontamination technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion of the erformance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility B. Treatment Technology Development of Uranium Sludge Analysis of the domestic and overseas research development status. Suggestion of treatment methodology of uranium slurry and cooperative R and D among industries, universities and research institute. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility C. Decommissioning Technology Development Analysis of the domestic and overseas research development status and the overview of decommissioning technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of TRIGA decommissioning D. Evaluation of KAERI Soil Decontamination Technology. Evaluation of soil decontamination process and the liquid decontamination waste treatment technology. Performance of soil decontamination test using solvent flushing test equipment for evaluation of residual radioactivity after decontami- nation and modeling of the results

  17. Current Status of Aerosol Generation and Measurement Facilities for the Verification Test of Containment Filtered Venting System in KAERI

    Kim, Sung Il; An, Sang Mo; Ha, Kwang Soon; Kim, Hwan Yeol [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    In this study, the design of aerosol generation and measurement systems are explained and present circumstances are also described. In addition, the aerosol test plan is shown. Containment Filtered Venting System (FCVS) is one of the safety features to reduce the amount of released fission product into the environment by depressurizing the containment. Since Chernobyl accident, the regulatory agency in several countries in Europe such as France, Germany, Sweden, etc. have been demanded the installation of the CFVS. Moreover, the feasibility study on the CFVS was also performed in U.S. After the Fukushima accident, there is a need to improve a containment venting or installation of depressurizing facility in Korea. As a part of a Ministry of Trade, Industry and Energy (MOTIE) project, KAERI has been conducted the integrated performance verification test of CFVS. As a part of the test, aerosol generation system and measurement systems were designed to simulate the fission products behavior. To perform the integrated verification test of CFVS, aerosol generation and measurement system was designed and manufactured. The component operating condition is determined to consider the severe accident condition. The test will be performed in normal conditions at first, and will be conducted under severe condition, high pressure and high temperature. Undesirable difficulties which disturb the elaborate test are expected, such as thermophoresis on the pipe, vapor condensation on aerosol, etc.

  18. A study on implementation plan of decontamination and decommissioning R and D and evaluation of KAERI soil decontamination process

    Oh, Won Zin; Lee, K. W.; Won, H. J.; Jung, C. H.; Choi, W. K.; Kim, G. N

    2001-08-01

    A. Decontamination Technology Development of Uranium Conversion Facility. Understanding of uranium conversion facility and related decontamination technologies, and analysis of current status of decontamination technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion of the erformance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility B. Treatment Technology Development of Uranium Sludge Analysis of the domestic and overseas research development status. Suggestion of treatment methodology of uranium slurry and cooperative R and D among industries, universities and research institute. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of environmental restoration of uranium conversion facility C. Decommissioning Technology Development Analysis of the domestic and overseas research development status and the overview of decommissioning technologies. Establishment of the objective and research items of the middle and long term R and D project. Discussion about the performance plan and about the methodology for connection with the project of TRIGA decommissioning D. Evaluation of KAERI Soil Decontamination Technology. Evaluation of soil decontamination process and the liquid decontamination waste treatment technology. Performance of soil decontamination test using solvent flushing test equipment for evaluation of residual radioactivity after decontami- nation and modeling of the results.

  19. Synthesis of the turbulent mixing in a rod bundle with vaned spacer grids based on the OECD-KAERI CFD benchmark exercise

    Lee, Jae Ryong; Kim, Jungwoo; Song, Chul-Hwa, E-mail: chsong@kaeri.re.kr

    2014-11-15

    Highlights: • OECD/KAERI international CFD benchmark exercise was operated by KAERI. • The purpose is to validate relevant CFD codes based on the MATiS-H experiments. • Blind calculation results were synthesized in terms of mean velocity and RMS. • Quality of control volume rather than the number of it was emphasized. • Major findings were followed OECD/NEA CSNI report. - Abstract: The second international CFD benchmark exercise on turbulent mixing in a rod bundle has been launched by OECD/NEA, to validate relevant CFD (Computational Fluid Dynamics) codes and develop problem-specific Best Practice Guidelines (BPG) based on the KAERI (Korea Atomic Energy Research Institute) MATiS-H experiments on the turbulent mixing in a 5 × 5 rod array having two different types of vaned spacer grids: split and swirl types. For this 2nd international benchmark exercise (IBE-2), the MATiS-H testing provided a unique set of experimental data such as axial and lateral velocity components, turbulent intensity, and vorticity information. Blind CFD calculation results were submitted by twenty-five (25) participants to KAERI, who is the host organization of the IBE-2, and then analyzed and synthesized by comparing them with the MATiS-H data. Based on the synthesis of the results from both the experiments and blind CFD calculations for the IBE-2, and also by comparing with the IBE-1 benchmark exercise on the mixing in a T-junction, useful information for simulating this kind of complicated physical problem in a rod bundle was obtained. And some additional Best Practice Guidelines (BPG) are newly proposed. A summary of the synthesis results obtained in the IBE-2 is presented in this paper.

  20. Synthesis of the turbulent mixing in a rod bundle with vaned spacer grids based on the OECD-KAERI CFD benchmark exercise

    Lee, Jae Ryong; Kim, Jungwoo; Song, Chul-Hwa

    2014-01-01

    Highlights: • OECD/KAERI international CFD benchmark exercise was operated by KAERI. • The purpose is to validate relevant CFD codes based on the MATiS-H experiments. • Blind calculation results were synthesized in terms of mean velocity and RMS. • Quality of control volume rather than the number of it was emphasized. • Major findings were followed OECD/NEA CSNI report. - Abstract: The second international CFD benchmark exercise on turbulent mixing in a rod bundle has been launched by OECD/NEA, to validate relevant CFD (Computational Fluid Dynamics) codes and develop problem-specific Best Practice Guidelines (BPG) based on the KAERI (Korea Atomic Energy Research Institute) MATiS-H experiments on the turbulent mixing in a 5 × 5 rod array having two different types of vaned spacer grids: split and swirl types. For this 2nd international benchmark exercise (IBE-2), the MATiS-H testing provided a unique set of experimental data such as axial and lateral velocity components, turbulent intensity, and vorticity information. Blind CFD calculation results were submitted by twenty-five (25) participants to KAERI, who is the host organization of the IBE-2, and then analyzed and synthesized by comparing them with the MATiS-H data. Based on the synthesis of the results from both the experiments and blind CFD calculations for the IBE-2, and also by comparing with the IBE-1 benchmark exercise on the mixing in a T-junction, useful information for simulating this kind of complicated physical problem in a rod bundle was obtained. And some additional Best Practice Guidelines (BPG) are newly proposed. A summary of the synthesis results obtained in the IBE-2 is presented in this paper

  1. THz radiation in KAERI

    Jeong, Young Uk; Cha, Hyuk Jin; Ahn, Pildong; Park, Seong Hee; Lee, Byung Cheol

    2006-01-01

    We have developed a high power terahertz (THz) radiation source by using a compact free electron laser (FEL). The FEL operates in the wavelength range of 100 - 1200 μm, which corresponds to 0.3-3 THz. The peak power of the FEL micropulse having 30 ps pulse duration is 1 kW and the pulse energy of the 3-μs-FEL-macropulse is approximately 0.3 mJ. The main application of the FEL is THz imaging and spectroscopy for bio-medical research and THz material study. We could get the transmitted THz imaging of several materials including bugs without being dryed by using the high power THz FEL. THz spectral characteristics of several materials have been studied by the FEL. We hope that the FEL can be upgraded for a practical source of medical and security inspections. (author)

  2. Review of the Safety Concern Related to CANDU Moderator Temperature Distribution and Status of KAERI Moderator Circulation Test (MCT) Experiments

    Rhee, Bo W.; Kim, Hyoung T. [Severe Accident and PHWR Safety Research Division, Daejeon (Korea, Republic of); Kim, Tongbeum [University of the Witwatersrand, Johannesburg (South Africa); Im, Sunghyuk [KAIST, Daejeon (Korea, Republic of)

    2015-10-15

    threshold temperature and no further deformation is expected. Consequently, a sufficient condition to ensure fuel channel integrity following a large LOCA, is the avoidance of sustained calandria tubes dryout. If the moderator available subcooling at the onset of a large LOCA is greater than the subcooling requirements, a sustained calandria tube dryout is avoided. The temperature oscillations observed in reactor and in test measurements such as MTF need to be characterized and quantified to show that it does not jeopardize the currently available safety margins. Because of the importance of an accurate prediction of moderator temperature distributions and the related moderator subcooling, a 1/4 scaled-down moderator tank of a CANDU-6 reactor, called Moderator Circulation Test (MCT), was erected at KAERI and the current status of MCT experiment progress is described and further experiments are expected to be carried out to generate the experimental data necessary to validate the computer codes that will be used to analyze the accident analysis of operating CANDU-6 plants.

  3. Implications of small water leak reactions on sodium heated steam generator design

    Smedley, J A

    1975-07-01

    Various types of sodium water reactions have been looked on as possibly causing hazard conditions in sodium heated steam generator units ranging from the very improbable boiler tube double ended guillotine fracture to the almost certain occurrence of micro-leaks. Within this range small water leaks reactions have attracted particular interest and the present paper looks at the principles of associating the reactions with detection and protection systems for Commercial Fast Reactors. A method is developed for assessing whether adequate protection has been provided against the effects of small water leak reactions in a steam generator unit. (author)

  4. Joint research project to develop a training course or nuclear policy decision makers and planners in developing countries between KAERI and IAEA

    Lee, E. J.; Suh, I. S.; Lee, H. Y. and others

    2000-12-01

    KAERI developed training course curricula on nuclear power policy and planning for decision makers and planners in developing countries under the assistance of the IAEA. It was utilized two IAEA staff members and a Korean consultation group were utilized for the development of curricula. Curriculum consists of training objectives, training contents in modular basis, detailed contents of each training module, training setting, training duration, session hours, and entry requirements of audience. One is workshop on nuclear energy policy for high-level decision makers in developing countries. The other is training course on nuclear power planning and project management for middle level managers in developing countries. The textbook in English will be printed by the end of February in 2001. Developed curricula will be implemented for Vietnam high level nuclear decision makers, middle level managers in developing countries and north Korea nuclear high level decision makers in 2001. These training courses' curricula and textbook will be utilized as basic technical documents to promote the national nuclear bilateral technical cooperation programs with Morocco, Egypt, Bangladesh, Indonesia, Ukraine, etc.

  5. Joint research project to develop a training course or nuclear policy decision makers and planners in developing countries between KAERI and IAEA

    Lee, E. J.; Suh, I. S.; Lee, H. Y. and others

    2000-12-01

    KAERI developed training course curricula on nuclear power policy and planning for decision makers and planners in developing countries under the assistance of the IAEA. It was utilized two IAEA staff members and a Korean consultation group were utilized for the development of curricula. Curriculum consists of training objectives, training contents in modular basis, detailed contents of each training module, training setting, training duration, session hours, and entry requirements of audience. One is workshop on nuclear energy policy for high-level decision makers in developing countries. The other is training course on nuclear power planning and project management for middle level managers in developing countries. The textbook in English will be printed by the end of February in 2001. Developed curricula will be implemented for Vietnam high level nuclear decision makers, middle level managers in developing countries and north Korea nuclear high level decision makers in 2001. These training courses' curricula and textbook will be utilized as basic technical documents to promote the national nuclear bilateral technical cooperation programs with Morocco, Egypt, Bangladesh, Indonesia, Ukraine, etc

  6. Conceptual Thermal Hydraulic Design of a 20MW Multipurpose Research Reactor (KAERI/VAEC joint study on a new research reactor for Vietnam)

    Chae, Hee Taek; Seo, Chul Gyo; Park, Jong Hark; Park, Cheol; Vinh, Le Vinh; Nghiem, Huynh Ton; Dang, Vo Doan Hai

    2007-08-01

    The conceptual thermal hydraulics design analyses for the 20 MW reference AHR core have been jointly performed by the KAERI and DNRI(VAEC). The preliminary core thermal hydraulic characteristics and safety margins for the AHR core were studied for various core flow rates, fuel assembly powers and core inlet temperatures. Statistical method was applied to the thermal hydraulic design of the reactor core. The MATRA h subchannel code has been applied to evaluate the thermal hydraulic performances of the AHR and the resulting thermal margins of the core under the forced convection cooling mode during a nominal power operation and the natural circulation mode during a reactor shutdown condition. In addition, typical accident analyses were carried out for a loss of flow accident by a primary pump seizure and a reactivity induced accident by a CAR rod withdrawal during a normal full power operation. The normal full power operation of the AHR was ensured with a sufficient safety margin for the onset of nucleate boiling phenomena. The AHR also had a sufficient natural circulation cooling capability to cool the core without the onset of nucleate boiling in the channel after a normal reactor shutdown and the anticipated transients. It was confirmed by the typical accident analyses that the AHR core was sufficiently protected from the loss of flow by the primary cooling pump seizure and the overpower transients by the CAR withdrawal from the MCHFR and fuel temperature points of view

  7. The first technical report for the improvement of R and D evaluation : Focusing on the evaluation reaction of R and D project investigator

    Yeo, Ji Won; Kim, I.C.; Won, B.C.; Kim, M.R. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1997-12-01

    The main objectives of this report are as follows. - Measuring the project manager's reaction on R and D evaluation and determining its influencing factors. - Testing the relationship between personal characteristics (tolence for ambiguity, risk-taking propensity, self-efficacy, Turn-over intention) and the outcome of Project Evaluation. - Presenting the useful information related to rebuilding a R and D Evaluation System of KAERI (Korea Atomic Energy Research Institute). 72 refs., 6 figs., 41 tabs. (Author)

  8. Nuclear reactions

    Lane, A.M.

    1980-01-01

    In reviewing work at Harwell over the past 25 years on nuclear reactions it is stated that a balance has to be struck in both experiment and theory between work on cross-sections of direct practical relevance to reactors and on those relevant to an overall understanding of reaction processes. The compound nucleus and direct process reactions are described. Having listed the contributions from AERE, Harwell to developments in nuclear reaction research in the period, work on the optical model, neutron capture theory, reactions at doorway states with fine structure, and sum-rules for spectroscopic factors are considered in more detail. (UK)

  9. Proceedings of the specialists' meeting on acoustic/ultrasonic detection of in sodium water leaks on steam generators, held in Aix-en-Provence, France, 1-3 October 1990

    Girard, J.P.

    1990-10-01

    23 officially nominated persons and 8 observers from 7 countries operating fast breeder reactors in the world, Mr. Arkhipov, IAEA Scientific Secretary of IWGFR and Mr. Cambillard, French member of IWGFR attended the specialists meeting. 25 papers were presented in the national status session and in 3 technical sessions devoted to methods, theoretical approach and real steam generator experience. A separate abstract was prepared for each of these papers. Since the last meetings in Dimitrovgrad and Petten it is clear that acoustic/ultrasonic monitoring of in-sodium water leaks is now considered by all countries as a major topic for commercial fast reactor steam generator unit protection. At this time the detection of leakage events is thought to be possible in the leak range from 1 to about 100 g/s in a time period of a few seconds to a few tens of seconds. Future work should aim at a more precise definition of the attainable limits, taking into account the particular requirements of actual plant design. Refs, figs and tabs

  10. Quasielastic reactions

    Henning, W.

    1979-01-01

    Quasielastic reaction studies, because of their capability to microscopically probe nuclear structure, are still of considerable interest in heavy-ion reactions. The recent progress in understanding various aspects of the reaction mechanism make this aim appear closer. The relation between microscopic and macroscopic behavior, as suggested, for example, by the single proton transfer data to individual final states or averaged excitation energy intervals, needs to be explored. It seems particularly useful to extend measurements to higher incident energies, to explore and understand nuclear structure aspects up to the limit of the energy range where they are important

  11. cycloaddition reactions

    Unknown

    Molecular Modeling Group, Organic Chemical Sciences, Indian Institute of Chemical Technology,. Hyderabad ... thus obtained are helpful to model the regioselectivity ... compromise to model Diels–Alder reactions involving ...... acceptance.

  12. Direct Reactions

    Austern, N. [University of Pittsburgh, Pittsburgh, PA (United States)

    1963-01-15

    In order to give a unified presentation of one point of view, these lectures are devoted only to a detailed development of the standard theories of direct reactions, starting from basic principles. Discussion is given of the present status of the theories, of the techniques used for practical calculation, and of possible future developments. The direct interaction (DI) aspects of a reaction are those which involve only a few of the many degrees of freedom of a nucleus. In fact the minimum number of degrees of freedom which must be involved in a reaction are those required to describe the initial and final channels, and DI studies typically consider these degrees of freedom and no others. Because of this simplicity DI theories may be worked out in painstaking detail. DI processes concern only part of the wave function for a problem. The other part involves complicated excitations of many degrees of freedom, and gives the compound nucleus (CN) effects. While it is extremely interesting to learn how to separate DI and CN effects in an orderly manner, if they are both present in a reaction, no suitable method has yet been found. Instead, current work stresses the kinds of reactions and the kinds of final states in which DI effects dominate and in which CN effects may almost be forgotten. The DI cross-sections which are studied are often extremely large, comparable to elastic scattering cross-sections. (author)

  13. Reaction mechanisms

    Nguyen Trong Anh

    1988-01-01

    The 1988 progress report of the Reaction Mechanisms laboratory (Polytechnic School, France), is presented. The research topics are: the valence bond methods, the radical chemistry, the modelling of the transition states by applying geometric constraints, the long range interactions (ion - molecule) in gaseous phase, the reaction sites in gaseous phase and the mass spectroscopy applications. The points of convergence between the investigations of the mass spectroscopy and the theoretical chemistry teams, as well as the purposes guiding the research programs, are discussed. The published papers, the conferences, the congress communications and the thesis, are also reported [fr

  14. Allergic reactions

    ... that don't bother most people (such as venom from bee stings and certain foods, medicines, and pollens) can ... person. If the allergic reaction is from a bee sting, scrape the ... more venom. If the person has emergency allergy medicine on ...

  15. Quasielastic reactions

    Hansen, O.

    1983-01-01

    A brief review is presented of the experimental and theoretical situation regarding transfer reactions and inelastic scattering. In the first category there is little (very little) precision data for heavy projectiles and consequently almost no experience with quantitative theoretical analysis. For the inelastic scattering the rather extensive data strongly supports the coupled channels models with collective formfactors. At the most back angles, at intensities about 10 -5 of Rutherford scattering, a second, compound-like mechanism becomes dominant. The description of the interplay of these two opposite mechanisms provides a new challenge for our understanding

  16. Nuclear reactions

    Corner, J.; Richardson, K.; Fenton, N.

    1990-01-01

    Nuclear reactions' marks a new development in the study of television as an agency of public policy debate. During the Eighties, nuclear energy became a major international issue. The disasters at Three-mile Island and Chernobyl created a global anxiety about its risks and a new sensitivity to it among politicians and journalists. This book is a case-study into documentary depictions of nuclear energy in television and video programmes and into the interpretations and responses of viewers drawn from many different occupational groupings. How are the complex and specialist arguments about benefit, risk and proof conveyed through the different conventions of commentary, interview and film sequence? What symbolic associations does the visual language of television bring to portrayals of the issue? And how do viewers make sense of various and conflicting accounts, connecting what they see and hear on the screen with their pre-existing knowledge, experience and 'civic' expectations. The authors examine some of the contrasting forms and themes which have been used by programme makers to explain and persuade, and then give a sustained analysis of the nature and sources of viewers' own accounts. 'Nuclear Reactions' inquires into the public meanings surrounding energy and the environment, spelling out in its conclusion some of the implications for future media treatments of this issue. It is also a key contribution to the international literature on 'television knowledge' and the processes of active viewing. (author)

  17. Spallation reactions; Reactions de spallation

    Cugon, J.

    1996-12-31

    Spallation reactions dominate the interactions of hadrons with nuclei in the GeV range (from {approx} 0.1 to {approx} 10 GeV). They correspond to a sometimes important ejection of light particles leaving most of the time a residue of mass commensurate with the target mass. The main features of the experimental data are briefly reviewed. The most successful theoretical model, namely the intranuclear cascade + evaporation model, is presented. Its physical content, results and possible improvements are critically discussed. Alternative approaches are shortly reviewed. (author). 84 refs.

  18. Chain reaction

    Balogh, Brian.

    1991-01-01

    Chain Reaction is a work of recent American political history. It seeks to explain how and why America came to depend so heavily on its experts after World War II, how those experts translated that authority into political clout, and why that authority and political discretion declined in the 1970s. The author's research into the internal memoranda of the Atomic Energy Commission substantiates his argument in historical detail. It was not the ravages of American anti-intellectualism, as so many scholars have argued, that brought the experts back down to earth. Rather, their decline can be traced to the very roots of their success after World War II. The need to over-state anticipated results in order to garner public support, incessant professional and bureaucratic specialization, and the sheer proliferation of expertise pushed arcane and insulated debates between experts into public forums at the same time that a broad cross section of political participants found it easier to gain access to their own expertise. These tendencies ultimately undermined the political influence of all experts. (author)

  19. Experimental Investigation of Gaseous Reaction Products from Na-CO{sub 2} Reaction in Na/CO{sub 2} Heat Exchanger leakage scenario

    Go, A-Reum; Jung, Hwa-Young; Kim, Min Seok; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of); Min, Jaehong; Wi, Myung-Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    The SFRs have operated with the steam Rankine cycle as a power conversion system. However, the potential sodium-water reaction (SWR) whose chemical reactivity is vigorous and instantaneous has been one of the major issues concerning the safety and integrity of the SFRs. In order to avoid SWR, supercritical CO{sub 2}(S-CO{sub 2}) Brayton cycles have been investigated recently. Compared to conventional steam Rankine cycles, S-CO{sub 2} Brayton cycle features higher thermal efficiency and potential compactness of its required equipment. In spite of the superiority of S-CO{sub 2} Brayton cycle, there is a potential reactive process between sodium and CO{sub 2} if the pressure boundary fails in the sodium-CO{sub 2} heat exchanger. The leakage scenario which could lead to mechanical and thermal problems should be evaluated. Previous studies have reported the following major reaction formulas. Each reaction occurs competitively. In this paper, the experimental setup to observe the pressure variation and CO concentration in Na-CO{sub 2} heat exchanger during the CO{sub 2} leak is explained. Before the experiment is carried out, water-CO{sub 2} mock-up test will be performed. In order to evaluate the leakage scenario in Na-CO{sub 2} heat exchanger more accurately, this study will be important for guaranteeing the system of SFR coupled with S-CO{sub 2} cycle.

  20. Chemical kinetics and reaction mechanism

    Jung, Ou Sik; Park, Youn Yeol

    1996-12-01

    This book is about chemical kinetics and reaction mechanism. It consists of eleven chapters, which deal with reaction and reaction speed on reaction mechanism, simple reaction by rate expression, reversible reaction and simultaneous reaction, successive reaction, complicated reaction mechanism, assumption for reaction mechanism, transition state theory, successive reaction and oscillating reaction, reaction by solution, research method high except kinetics on reaction mechanism, high reaction of kinetics like pulsed radiolysis.

  1. Treatment and Managing Reactions

    ... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food ... a severe reaction. Consider wearing an emergency medical identification (e.g., bracelet, other jewelry). What to Read ...

  2. Microfluidic chemical reaction circuits

    Lee, Chung-cheng [Irvine, CA; Sui, Guodong [Los Angeles, CA; Elizarov, Arkadij [Valley Village, CA; Kolb, Hartmuth C [Playa del Rey, CA; Huang, Jiang [San Jose, CA; Heath, James R [South Pasadena, CA; Phelps, Michael E [Los Angeles, CA; Quake, Stephen R [Stanford, CA; Tseng, Hsian-rong [Los Angeles, CA; Wyatt, Paul [Tipperary, IE; Daridon, Antoine [Mont-Sur-Rolle, CH

    2012-06-26

    New microfluidic devices, useful for carrying out chemical reactions, are provided. The devices are adapted for on-chip solvent exchange, chemical processes requiring multiple chemical reactions, and rapid concentration of reagents.

  3. Preequilibrium Nuclear Reactions

    Strohmaier, B.

    1988-01-01

    After a survey on existing experimental data on precompound reactions and a description of preequilibrium reactions, theoretical models and quantum mechanical theories of preequilibrium emission are presented. The 25 papers of this meeting are analyzed separately

  4. Managing Your Emotional Reactions

    ... Videos for Educators Search English Español Managing Your Emotional Reactions KidsHealth / For Teens / Managing Your Emotional Reactions ... Think about what you might do next time. Emotions 101 The skills we use to manage our ...

  5. Heavy ion transfer reactions

    array (CLARA), extensive investigations of nuclear structure and reaction dynamics have been carried out. In the present paper aspects of these studies will be presented, focussing more closely on the reaction mechanism, in particular on the ...

  6. Chemical transport reactions

    Schäfer, Harald

    2013-01-01

    Chemical Transport Reactions focuses on the processes and reactions involved in the transport of solid or liquid substances to form vapor phase reaction products. The publication first offers information on experimental and theoretical principles and the transport of solid substances and its special applications. Discussions focus on calculation of the transport effect of heterogeneous equilibria for a gas motion between equilibrium spaces; transport effect and the thermodynamic quantities of the transport reaction; separation and purification of substances by means of material transport; and

  7. Thermonuclear reaction rates. III

    Harris, M.J.; Fowler, W.A.; Caughlan, G.R.; Zimmerman, B.A.

    1983-01-01

    Stellar thermonuclear reaction rates are revised and updated, adding a number of new important reaction rates. Several reactions with large negative Q-values are included, and examples of them are discussed. The importance of the decay rates for Mg-26(p,n) exp 26 Al and Al-26(n,p) exp 26 Mg for stellar studies is emphasized. 19 references

  8. Maillard Reaction: review

    Júlia d'Almeida Francisquini

    2017-11-01

    Full Text Available Maillard reaction is an important subject of study in food science and technology and different areas of knowledge are involved such as chemistry, food engineering, nutrition and food technology. The objective of this paper is to present the basic concepts of the Maillard reaction, such as the reaction stages, the main compounds producced and some technological consequences for dairy products.

  9. Resonant thermonuclear reaction rate

    Haubold, H.J.; Mathai, A.M.

    1986-01-01

    Basic physical principles for the resonant and nonresonant thermonuclear reaction rates are applied to find their standard representations for nuclear astrophysics. Closed-form representations for the resonant reaction rate are derived in terms of Meijer's G-function. Analytic representations of the resonant and nonresonant nuclear reaction rates are compared and the appearance of Meijer's G-function is discussed in physical terms

  10. Insights into the mechanisms on chemical reactions: reaction paths for chemical reactions

    Dunning, T.H. Jr.; Rosen, E.; Eades, R.A.

    1987-01-01

    We report reaction paths for two prototypical chemical reactions: Li + HF, an electron transfer reaction, and OH + H 2 , an abstraction reaction. In the first reaction we consider the connection between the energetic terms in the reaction path Hamiltonian and the electronic changes which occur upon reaction. In the second reaction we consider the treatment of vibrational effects in chemical reactions in the reaction path formalism. 30 refs., 9 figs

  11. Noncanonical Reactions of Flavoenzymes

    Pablo Sobrado

    2012-11-01

    Full Text Available Enzymes containing flavin cofactors are predominantly involved in redox reactions in numerous cellular processes where the protein environment modulates the chemical reactivity of the flavin to either transfer one or two electrons. Some flavoenzymes catalyze reactions with no net redox change. In these reactions, the protein environment modulates the reactivity of the flavin to perform novel chemistries. Recent mechanistic and structural data supporting novel flavin functionalities in reactions catalyzed by chorismate synthase, type II isopentenyl diphosphate isomerase, UDP-galactopyranose mutase, and alkyl-dihydroxyacetonephosphate synthase are presented in this review. In these enzymes, the flavin plays either a direct role in acid/base reactions or as a nucleophile or electrophile. In addition, the flavin cofactor is proposed to function as a “molecular scaffold” in the formation of UDP-galactofuranose and alkyl-dihydroxyacetonephosphate by forming a covalent adduct with reaction intermediates.

  12. Nuclear reaction studies

    Alexander, J.M.; Lacey, R.A.

    1994-01-01

    Research focused on the statistical and dynamical properties of ''hot'' nuclei formed in symmetric heavy-ion reactions. Theses included ''flow'' measurements and the mechanism for multifragment disassembly. Model calculations are being performed for the reactions C+C, Ne+Al, Ar+Sc, Kr+Nb, and Xe+La. It is planned to study 40 Ar reactions from 27 to 115 MeV/nucleon. 2 figs., 41 refs

  13. Knock-out reactions

    de Forest, T. Jr.

    1977-01-01

    It is pointed out that the primary motivation for performing high energy single nucleon knock-out reactions is based on the concept of quasi-elastic scattering. The validity of and corrections to the partial wave impulse approximation and kinematical invariance of knock-out reactions and tests of the reaction mechanism are treated. The effect of distortions on the momentum distribution in the effective momentum approximation for given parameters are plotted. 12 references

  14. Reaction kinetics of polybutylene terephthalate polycondensation reaction

    Darda, P. J.; Hogendoorn, J. A.; Versteeg, G. F.; Souren, F.

    2005-01-01

    The kinetics of the forward polycondensation reaction of polybutylene terephthalate (PBT) has been investigated using thermogravimetric analysis (TGA). PBT - prepolymer with an initial degree of polymerization of 5.5 was used as starting material. The PBT prepolymer was prepared from dimethyl

  15. Thermonuclear reaction listing

    Fukai, Yuzo

    1993-01-01

    The following 10 elements, including T, are well known as nuclear fusion fuels: p, D, T, 3 He, 4 He, 6 Li, 7 Li, 9 Be, 10 B, 11 B, ( 12 C, 13 C), where 12 C and 13 C are considered only in the calculation of Q value. Accordingly the number of the thermonuclear reactions is 55, and 78, if including carbon elements. The reactions have some branches. For the branches having two and three reaction products, the reaction products, Q value and threshold energy are calculated by using a computer. We have investigated those of the branches having more than three products from the papers of Ajzenberg-Selove and so on. And also, by the same papers, we check whether the above mentioned branch has been observed or not. The results are as follows: (I) the number of reactions which have Q 0 branches only with γ ray production, and Q 0 and neutron production is 36(17), and (IV) that of reactions whose branch with Q > 0 does not produce neutrons is 9(3). The value in the parentheses shows the number of the case of the carbon elements. For 55 thermonuclear reactions induced by lighter nuclides than 11 B, the reaction products, the values of Q and threshold energy, and the papers with reaction cross section data are presented in the tables. (author)

  16. Sleeve reaction chamber system

    Northrup, M Allen [Berkeley, CA; Beeman, Barton V [San Mateo, CA; Benett, William J [Livermore, CA; Hadley, Dean R [Manteca, CA; Landre, Phoebe [Livermore, CA; Lehew, Stacy L [Livermore, CA; Krulevitch, Peter A [Pleasanton, CA

    2009-08-25

    A chemical reaction chamber system that combines devices such as doped polysilicon for heating, bulk silicon for convective cooling, and thermoelectric (TE) coolers to augment the heating and cooling rates of the reaction chamber or chambers. In addition the system includes non-silicon-based reaction chambers such as any high thermal conductivity material used in combination with a thermoelectric cooling mechanism (i.e., Peltier device). The heat contained in the thermally conductive part of the system can be used/reused to heat the device, thereby conserving energy and expediting the heating/cooling rates. The system combines a micromachined silicon reaction chamber, for example, with an additional module/device for augmented heating/cooling using the Peltier effect. This additional module is particularly useful in extreme environments (very hot or extremely cold) where augmented heating/cooling would be useful to speed up the thermal cycling rates. The chemical reaction chamber system has various applications for synthesis or processing of organic, inorganic, or biochemical reactions, including the polymerase chain reaction (PCR) and/or other DNA reactions, such as the ligase chain reaction.

  17. Tattoo reaction: Case series

    Muneer Mohamed

    2018-04-01

    Full Text Available Tattoo is going to be a very common practice especially among young people and we are witnessing a gradual increase of numerous potential complications to tattoo placement which are often seen by physicians, but generally unknown to the public. The most common skin reactions to tattoo include a transient acute inflammatory reaction due to trauma of the skin with needles and medical complications such as superficial and deep local infections, systemic infections, allergic contact dermatitis, photodermatitis, granulomatous and lichenoid reactions, and skin diseases localized on tattooed area (eczema, psoriasis, lichen, and morphea. In this series we present three cases of tattoo reaction.

  18. Hydrogen evolution reaction catalyst

    Subbaraman, Ram; Stamenkovic, Vojislav; Markovic, Nenad; Tripkovic, Dusan

    2016-02-09

    Systems and methods for a hydrogen evolution reaction catalyst are provided. Electrode material includes a plurality of clusters. The electrode exhibits bifunctionality with respect to the hydrogen evolution reaction. The electrode with clusters exhibits improved performance with respect to the intrinsic material of the electrode absent the clusters.

  19. Precompound Reactions: Basic Concepts

    Weidenmueller, H. A.

    2008-01-01

    Because of the non-zero nuclear equilibration time, the compound-nucleus scattering model fails when the incident energy exceeds 10 or 20 MeV, and precompound reactions become important. Basic ideas used in the quantum-statistical approaches to these reactions are described

  20. Nuclear Reaction Data Centers

    McLane, V.; Nordborg, C.; Lemmel, H.D.; Manokhin, V.N.

    1988-01-01

    The cooperating Nuclear Reaction Data Centers are involved in the compilation and exchange of nuclear reaction data for incident neutrons, charged particles and photons. Individual centers may also have services in other areas, e.g., evaluated data, nuclear structure and decay data, reactor physics, nuclear safety; some of this information may also be exchanged between interested centers. 20 refs., 1 tab

  1. Fluorogenic organocatalytic reactions

    Raeisolsadati Oskouei, M.

    2017-01-01

    In this thesis, we introduce fluorescence spectroscopy as a new tool to gain insight into the interactions between the substrates and catalyst during organocatalytic reactions. The ultimate goal is to resolve the kinetics of the binding and reaction steps and obtain detailed understanding of the

  2. Applications of Reaction Rate

    Cunningham, Kevin

    2007-01-01

    This article presents an assignment in which students are to research and report on a chemical reaction whose increased or decreased rate is of practical importance. Specifically, students are asked to represent the reaction they have chosen with an acceptable chemical equation, identify a factor that influences its rate and explain how and why it…

  3. Chemical burn or reaction

    Chemicals that touch skin can lead to a reaction on the skin, throughout the body, or both. ... leave the person alone and watch carefully for reactions affecting the entire body. Note: If a chemical gets into the eyes, the eyes should be ...

  4. Degradations and Rearrangement Reactions

    Zhang, Jianbo

    This section deals with recent reports concerning degradation and rearrangement reactions of free sugars as well as some glycosides. The transformations are classified in chemical and enzymatic ways. In addition, the Maillard reaction will be discussed as an example of degradation and rearrangement transformation and its application in current research in the fields of chemistry and biology.

  5. Analysis of the flow with phase change and chemical reaction with the particle interaction method. Report under the contract between JNC and Toshiba Corporation

    Shirakawa, Noriyuki; Horie, Hideki; Yamamoto, Yuichi

    2001-02-01

    The numerical thermohydraulic analysis of a LMFR component should involve its whole boundary in order to evaluate the effect of chemical reaction within it. Therefore, it becomes difficult mainly due to computing time to adopt microscopic approach for the chemical reaction directly. Thus, the thermohydraulic code is required to model the chemically reactive fluid dynamics with constitutive correlations. The reaction rate depends on the binary contact areas between components such as continuous liquids, droplets, solid particles, and bubbles. The contact areas change sharply according to the interface state between components. Since no experiments to study the jet flow with sodium-water chemical reaction have been done, the goal of this study is to obtain the knowledge of flow regimes and contact areas by analyzing the fluid dynamics of multi-phase and reactive components mechanistically with the particle interaction method. In this fiscal year, following works were performed: 1) Development and coding of the interfacial area model, 2) Development and coding of the phase change model, 3) Verification of the fundamental functions of the models, and 4) Literature investigation of the related experiments. (author)

  6. Heavy ion transfer reactions

    Weisser, D.C.

    1977-06-01

    To complement discussions on the role of γ rays in heavy ion induced reactions, the author discusses the role played by particle detection. Transfer reactions are part of this subject and are among those in which one infers the properties of the residual nucleus in a reaction by observing the emerging light nucleus. Inelastic scattering ought not be excluded from this subject, although no particles are transferred, because of the role it plays in multistep reactions and in fixing O.M. parameters describing the entrance channel of the reaction. Heavy ion transfer reaction studies have been under study for some years and yet this research is still in its infancy. The experimental techniques are difficult and the demands on theory rigorous. One of the main products of heavy ion research has been the thrust to re-examine the assumptions of reaction theory and now include many effects neglected for light ion analysis. This research has spurred the addition of multistep processes to simple direct processes and coupled channel calculations. (J.R.)

  7. Enhancing chemical reactions

    Morrey, John R.

    1978-01-01

    Methods of enhancing selected chemical reactions. The population of a selected high vibrational energy state of a reactant molecule is increased substantially above its population at thermal equilibrium by directing onto the molecule a beam of radiant energy from a laser having a combination of frequency and intensity selected to pump the selected energy state, and the reaction is carried out with the temperature, pressure, and concentrations of reactants maintained at a combination of values selected to optimize the reaction in preference to thermal degradation by transforming the absorbed energy into translational motion. The reaction temperature is selected to optimize the reaction. Typically a laser and a frequency doubler emit radiant energy at frequencies of .nu. and 2.nu. into an optical dye within an optical cavity capable of being tuned to a wanted frequency .delta. or a parametric oscillator comprising a non-centrosymmetric crystal having two indices of refraction, to emit radiant energy at the frequencies of .nu., 2.nu., and .delta. (and, with a parametric oscillator, also at 2.nu.-.delta.). Each unwanted frequency is filtered out, and each desired frequency is focused to the desired radiation flux within a reaction chamber and is reflected repeatedly through the chamber while reactants are fed into the chamber and reaction products are removed therefrom.

  8. The Reaction Wheel Pendulum

    Block, Daniel J; Spong, Mark W

    2007-01-01

    This monograph describes the Reaction Wheel Pendulum, the newest inverted-pendulum-like device for control education and research. We discuss the history and background of the reaction wheel pendulum and other similar experimental devices. We develop mathematical models of the reaction wheel pendulum in depth, including linear and nonlinear models, and models of the sensors and actuators that are used for feedback control. We treat various aspects of the control problem, from linear control of themotor, to stabilization of the pendulum about an equilibrium configuration using linear control, t

  9. Electron transfer reactions

    Cannon, R D

    2013-01-01

    Electron Transfer Reactions deals with the mechanisms of electron transfer reactions between metal ions in solution, as well as the electron exchange between atoms or molecules in either the gaseous or solid state. The book is divided into three parts. Part 1 covers the electron transfer between atoms and molecules in the gas state. Part 2 tackles the reaction paths of oxidation states and binuclear intermediates, as well as the mechanisms of electron transfer. Part 3 discusses the theories and models of the electron transfer process; theories and experiments involving bridged electron transfe

  10. Firefighter Nozzle Reaction

    Chin, Selena K.; Sunderland, Peter B.; Jomaas, Grunde

    2017-01-01

    to anchor forces, the hose becomes straight. The nozzle reaction is found to equal the jet momentum flow rate, and it does not change when an elbow connects the hose to the nozzle. A forward force must be exerted by a firefighter or another anchor that matches the forward force that the jet would exert...... on a perpendicular wall. Three reaction expressions are derived, allowing it to be determined in terms of hose diameter, jet diameter, flow rate, and static pressure upstream of the nozzle. The nozzle reaction predictions used by the fire service are 56% to 90% of those obtained here for typical firefighting hand...

  11. Nucleon induced reactions

    Gmuca, S.; Antalik, R.; Kristiak, J.

    1988-01-01

    The collection contains full texts of 37 contributions; all fall within the INIS Subject Scope. The topics treated include some unsolved problems of nuclear reactions and relevant problems of nuclear structure at low and intermediate energies. (Z.S.)

  12. Reactor for exothermic reactions

    Smith, L.A. Jr.; Hearn, D.; Jones, E.M. Jr.

    1993-03-02

    A liquid phase process is described for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F. Wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  13. Statistical nuclear reactions

    Hilaire, S.

    2001-01-01

    A review of the statistical model of nuclear reactions is presented. The main relations are described, together with the ingredients necessary to perform practical calculations. In addition, a substantial overview of the width fluctuation correction factor is given. (author)

  14. Photon induced reactions

    Mecking, B.A.

    1982-04-01

    Various aspects of medium energy nuclear reactions induced by real photons are reviewed. Special emphasis is put on high accuracy experiments that will become possible with the next generation of electron accelerators. (orig.)

  15. Transfusion reaction - hemolytic

    ... Names Blood transfusion reaction Images Surface proteins causing rejection References Choate JD, Maitta RW, Tormey CA, Wu ... PA: Elsevier Saunders; 2016:chap 177. Hall JE. Blood types; transfusion; tissue and organ transplantation. In: Hall JE, ...

  16. Sequential charged particle reaction

    Hori, Jun-ichi; Ochiai, Kentaro; Sato, Satoshi; Yamauchi, Michinori; Nishitani, Takeo

    2004-01-01

    The effective cross sections for producing the sequential reaction products in F82H, pure vanadium and LiF with respect to the 14.9-MeV neutron were obtained and compared with the estimation ones. Since the sequential reactions depend on the secondary charged particles behavior, the effective cross sections are corresponding to the target nuclei and the material composition. The effective cross sections were also estimated by using the EAF-libraries and compared with the experimental ones. There were large discrepancies between estimated and experimental values. Additionally, we showed the contribution of the sequential reaction on the induced activity and dose rate in the boundary region with water. From the present study, it has been clarified that the sequential reactions are of great importance to evaluate the dose rates around the surface of cooling pipe and the activated corrosion products. (author)

  17. Reaction Qualifications Revisited

    Lippert-Rasmussen, Kasper

    2009-01-01

    to a person's effectiveness by causing a favourable reaction in customers, co-workers etc. (for short: recipients) - are involved, this assumption is false. Building on work by Wertheimer, Mason, and Miller, this paper proposes an account of the reaction qualifications that count, from the point of view...... preferences, recipients should not respond to the applicant actually hired on the basis of their (the recipients') racial preferences. My account decomposes the meritocratic ideal into four separate norms, one of which applies to recipients rather than to selectors. Finally, it defends the view that reaction...... qualifications based on antimeritocratic reactions, while not unproblematic, are not entirely irrelevant from the point of view of merit. Notably, selectors need not discount them when no one - including the targets of the objectionable preferences - is unfairly disadvantaged. Because not all problematic...

  18. Cutaneous adverse drug reactions

    CADRs).1 ... patient's management is thought to be responsible for the reaction. Some clinical ... In SJS/TEN hypotension, diarrhoea, hypothermia and confusion suggest ... and a pain management team, centred around a good core of experienced ...

  19. Reaction Qualifications Revisited

    Lippert-Rasmussen, Kasper

    2009-01-01

      When, in a competitive sphere, people are selected on the basis of qualifications only, their chances of acquiring positions of advantage may seem to depend entirely upon their abilities, not discriminatory bias. However, if reaction qualifications - i.e. characteristics which contribute...... to a person's effectiveness by causing a favourable reaction in customers, co-workers etc. (for short: recipients) - are involved, this assumption is false. Building on work by Wertheimer, Mason, and Miller, this paper proposes an account of the reaction qualifications that count, from the point of view...... of merit. Specifically, it preserves symmetry between negative evaluations of antimeritocratic bases of selection and negative evaluations of qualifications rooted in comparable antimeritocratic reactions. So if employers should not select among applicants on the basis of their (the employers') racial...

  20. Firefighter Nozzle Reaction

    Chin, Selena K.; Sunderland, Peter B.; Jomaas, Grunde

    2017-01-01

    Nozzle reaction and hose tension are analyzed using conservation of fluid momentum and assuming steady, inviscid flow and a flexible hose in frictionless contact with the ground. An expression that is independent of the bend angle is derived for the hose tension. If this tension is exceeded owing...... to anchor forces, the hose becomes straight. The nozzle reaction is found to equal the jet momentum flow rate, and it does not change when an elbow connects the hose to the nozzle. A forward force must be exerted by a firefighter or another anchor that matches the forward force that the jet would exert...... on a perpendicular wall. Three reaction expressions are derived, allowing it to be determined in terms of hose diameter, jet diameter, flow rate, and static pressure upstream of the nozzle. The nozzle reaction predictions used by the fire service are 56% to 90% of those obtained here for typical firefighting hand...

  1. Oxygen evolution reaction catalysis

    Haber, Joel A.; Jin, Jian; Xiang, Chengxiang; Gregoire, John M.; Jones, Ryan J.; Guevarra, Dan W.; Shinde, Aniketa A.

    2016-09-06

    An Oxygen Evolution Reaction (OER) catalyst includes a metal oxide that includes oxygen, cerium, and one or more second metals. In some instances, the cerium is 10 to 80 molar % of the metals in the metal oxide and/or the catalyst includes two or more second metals. The OER catalyst can be included in or on an electrode. The electrode can be arranged in an oxygen evolution system such that the Oxygen Evolution Reaction occurs at the electrode.

  2. Spallation reactions: calculations

    Bertini, H.W.

    1975-01-01

    Current methods for calculating spallation reactions over various energy ranges are described and evaluated. Recent semiempirical fits to existing data will probably yield the most accurate predictions for these reactions in general. However, if the products in question have binding energies appreciably different from their isotropic neighbors and if the cross section is approximately 30 mb or larger, then the intranuclear-cascade-evaporation approach is probably better suited. (6 tables, 12 figures, 34 references) (U.S.)

  3. Analysis of Decay Heat Removal by Natural Convection in LMR with a Combined Steam Generator

    Kim, Eui Kwang; Eoh, Jae Hyuk; Han, Ji Woong; Lee, Tae Ho

    2011-01-01

    Liquid metal reactors (LMRs) conventionally employ an intermediate heat transport system (IHTS) to protect the nuclear core during a sodium-water reaction (SWR) event. However these SWR-related components increase plant construction costs. In order to eliminate the need for an IHTS, a combined steam generator, which is an integrated heat exchanger of a steam generator and intermediate heat exchanger (IHX), was proposed by the Korea Atomic Energy Research Institute (KAERI). The objective of this work is to analyze the natural circulation heat removal capability of the rector system using a combined steam generator. As a means of decay heat removal, a normal heat transport path is composed of a primary sodium system, intermediate lead-bismuth circuit combined with SG and steam/water system. This paper presents the results of the possible temperature and natural circulation flows in all circuits during a steady state for a given reactor power level varied as a function of time

  4. Global Controllability of Chemical Reactions

    Drexler, Dániel András; Tóth, János

    2015-01-01

    Controllability of chemical reactions is an important problem in chemical engineering science. In control theory, analysis of the controllability of linear systems is well-founded, however the dynamics of chemical reactions is usually nonlinear. Global controllability properties of chemical reactions are analyzed here based on the Lie-algebra of the vector fields associated to elementary reactions. A chemical reaction is controllable almost everywhere if all the reaction rate coefficients can...

  5. Introduction to chemical reaction engineering

    Kim, Yeong Geol

    1990-10-01

    This deals with chemical reaction engineering with thirteen chapters. The contents of this book are introduction on reaction engineering, chemical kinetics, thermodynamics and chemical reaction, abnormal reactor, non-isothermal reactor, nonideal reactor, catalysis in nonuniform system, diffusion and reaction in porosity catalyst, design catalyst heterogeneous reactor in solid bed, a high molecule polymerization, bio reaction engineering, reaction engineering in material process, control multi-variable reactor process using digital computer.

  6. Chemical kinetics of gas reactions

    Kondrat'Ev, V N

    2013-01-01

    Chemical Kinetics of Gas Reactions explores the advances in gas kinetics and thermal, photochemical, electrical discharge, and radiation chemical reactions. This book is composed of 10 chapters, and begins with the presentation of general kinetic rules for simple and complex chemical reactions. The next chapters deal with the experimental methods for evaluating chemical reaction mechanisms and some theories of elementary chemical processes. These topics are followed by discussions on certain class of chemical reactions, including unimolecular, bimolecular, and termolecular reactions. The rema

  7. Inflammatory reaction in chondroblastoma

    Yamamura, Sigeki; Sato, Keiji; Sugiura, Hideshi; Iwata, Hisashi

    1996-01-01

    The objective of this study was to evaluate the inflammatory reaction accompanying chondroblastoma and to define the value of the finding in clinical practice. We reviewed the clinical, radiographic, and magnetic resonance (MR) findings in six patients with histologically proven chondroblastoma. In all cases, MR imaging showered marrow and soft tissue edema. In four of six cases, periosteal reaction related to intra-osseous edema was more clearly demonstrated on MR imaging than on radiographs. Follow-up MR studies after surgery were available in three patients and all showed disappearance of inflammatory responses such as marrow and soft tissue edema, and reactive synovitis. We propose that these inflammatory reactions of chondroblastomas are inportant signs for detecting residual tumor in recurrences after surgery, as well as for making a precise diagnosis. The MR changes may also be valuable in demonstrating eradication of the tumor. (orig./MG)

  8. Inflammatory reaction in chondroblastoma

    Yamamura, Sigeki [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Sato, Keiji [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Sugiura, Hideshi [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan); Iwata, Hisashi [Dept. of Orthopedic Surgery, Nagoya Univ. School of Medicine (Japan)

    1996-05-01

    The objective of this study was to evaluate the inflammatory reaction accompanying chondroblastoma and to define the value of the finding in clinical practice. We reviewed the clinical, radiographic, and magnetic resonance (MR) findings in six patients with histologically proven chondroblastoma. In all cases, MR imaging showered marrow and soft tissue edema. In four of six cases, periosteal reaction related to intra-osseous edema was more clearly demonstrated on MR imaging than on radiographs. Follow-up MR studies after surgery were available in three patients and all showed disappearance of inflammatory responses such as marrow and soft tissue edema, and reactive synovitis. We propose that these inflammatory reactions of chondroblastomas are inportant signs for detecting residual tumor in recurrences after surgery, as well as for making a precise diagnosis. The MR changes may also be valuable in demonstrating eradication of the tumor. (orig./MG)

  9. Knockout reactions: experimental aspects

    Cortina Gil, D. [Santiago de Compostela Univ. (Spain)

    2007-07-01

    The availability of radioactive beams has given rise to intense activity in the field of direct reactions. The removal of one(two)-nucleon (referred to as nucleon knockout in this text) from a fast exotic projectile has been extensively investigated. This lecture provides a general overview of the experimental results achieved using this technique. The sensitivity of the method to different experimental aspects is illustrated with a few examples. Special attention is given to the application of nucleon-knockout reactions as a general purpose spectroscopic tool. (author)

  10. Reactions to dietary tartrazine.

    David, T J

    1987-01-01

    Double blind challenges with tartrazine and benzoic acid were performed in hospital in 24 children whose parents gave a definite history of a purely behavioural immediate adverse reaction to one of these substances. The patients, whose ages ranged from 1.6 to 12.4 years, were on a diet that avoided these items, and in all there was a clear history that any lapse of the diet caused an obvious adverse behavioural reaction within two hours. In no patient was any change in behaviour noted either ...

  11. Nuclear fission and reactions

    Anon.

    1975-01-01

    The nuclear fission research programs are designed to elucidate basic features of the fission process. Specifically, (1) factors determining how nucleons of a fissioning nucleus are distributed between two fission fragments, (2) factors determining kinetic energy and excitation energies of fragments, and (3) factors controlling fission lifetimes. To these ends, fission studies are reported for several heavy elements and include investigations of spontaneous and neutron-induced fission, heavy ion reactions, and high energy proton reactions. The status of theoretical research is also discussed. (U.S.)

  12. Modeling of Reaction Calorimeter

    Farzad, Reza

    2014-01-01

    The purpose of this project was to model the reaction calorimeter in order to calculate the heat of absorption which is the most important parameter in this work. Reaction calorimeter is an apparatus which is used in measuring the heat of absorption of CO2 as well as the total pressure in vapor phase based on vapor-liquid equilibrium state. Mixture of monoethanolamine (MEA) and water was used as a solvent to absorb the CO2.Project was divided in to three parts in order to make the programming...

  13. Introduction to nuclear reactions

    Satchler, G.R.

    1980-01-01

    This introduction to nuclear reaction phenomena is aimed primarily but not exclusively at readers at the undergraduate student level. An overview of the subject is presented in the first two chapters entitled - Some background information and Introduction to nuclear reactions. The third chapter reviews scattering theory with emphasis on the underlying physical ideas and also provides schematic entrees to the more advanced topics. The physical models which have been developed to account for the various aspects of nuclear phenomena are described in more detail in chapter 4. References and exercises are appended to each chapter. (U.K.)

  14. Knockout reactions: experimental aspects

    Cortina Gil, D.

    2007-01-01

    The availability of radioactive beams has given rise to intense activity in the field of direct reactions. The removal of one(two)-nucleon (referred to as nucleon knockout in this text) from a fast exotic projectile has been extensively investigated. This lecture provides a general overview of the experimental results achieved using this technique. The sensitivity of the method to different experimental aspects is illustrated with a few examples. Special attention is given to the application of nucleon-knockout reactions as a general purpose spectroscopic tool. (author)

  15. Potential Improvements of Supercritical Recompression CO2 Brayton Cycle Coupled with KALIMER-600 by Modifying Critical Point of CO2

    Jeong, Woo Seok; Lee, Jeong Ik; Jeong, Yong Hoon; No, Hee Cheon

    2010-01-01

    Most of the existing designs of a Sodium cooled Fast Reactor (SFR) have a Rankine cycle as an electric power generation cycle. This has the risk of a sodium water reaction. To prevent any hazards from a sodium water reaction, an indirect Brayton cycle using Supercritical Carbon dioxide (S-CO 2 ) as the working fluids for a SFR is an alternative approach to improve the current SFR design. The supercritical Brayton cycle is defined as a cycle with operating conditions above the critical point and the main compressor inlet condition located slightly above the critical point of working fluid. This is because the main advantage of the cycle comes from significantly decreased compressor work just above the critical point due to high density near boundary between supercritical state and subcritical state. For this reason, the minimum temperature and pressure of cycle are just above the CO 2 critical point. In other words, the critical point acts as a limitation of the lowest operating condition of the cycle. In general, lowering the minimum temperature of a thermodynamic cycle can increase the efficiency and the minimum temperature can be decreased by shifting the critical point of CO 2 as mixed with other gases. In this paper, potential enhancement of S-CO 2 cycle coupled with KALIMER-600, which has been developed at KAERI, was investigated using a developed cycle code with a gas mixture property program

  16. (MIRC) reaction w

    Sudesh Kumari

    eco-friendly solvents, high yields and easy work-up procedure. Keywords. Ethylene glycol; 4-hydroxycoumarin; ... ability and also compatibility with most organic and inorganic compounds. Because of these properties it is ..... phenyl amino)-2H-chromen-2-one (8a) was isolated from the reaction mixture to confirm the ...

  17. Explaining competitive reaction effects

    Leeflang, P.S.H.; Wittink, D.R.

    Changes in promotional expenditure decisions for a brand, as in other marketing decisions, should be based on the expected impact on purchase and consumption behavior as well as on the likely reactions by competitors. Purchase behavior may be predicted from estimated demand functions. Competitive

  18. Oral Hypersensitivity Reactions

    ... and ulcers. Affected individuals may complain of a burning sensation and mouth sensitivity to cold, hot, and spicy foods. Lichenoid ... melon, and pineapple, are all associated with this syndrome. You should inform your ... reaction in the mouth, though some are more common than others. If ...

  19. Reaction Formulation: A Bibliography.

    Pedrini, D. T.; Pedrini, Bonnie C.

    Reaction formation was studied by Sigmund Freud. This defense mechanism may be related to repression, substitution, reversal, and compensation (or over-compensation). Alfred Adler considered compensation a basic process in his individual psychology. Anna Freud discussed some defense mechanisms, and Bibring, Dwyer, Huntington, and Valenstein…

  20. Reaction schemes of immunoanalysis

    Delaage, M.; Barbet, J.

    1991-01-01

    The authors apply a general theory for multiple equilibria to the reaction schemes of immunoanalysis, competition and sandwich. This approach allows the manufacturer to optimize the system and provide the user with interpolation functions for the standard curve and its first derivative as well, thus giving access to variance [fr

  1. Allergic reactions in anaesthesia

    Krøigaard, M; Garvey, L H; Menné, T

    2005-01-01

    a significant number of patients at unnecessary risk. Some patients may be labelled with a wrong allergy, leading to unnecessary warnings against harmless substances, and some patients may be put at risk of subsequent re-exposure to the real allergen. Patients with suspected allergic reactions during...

  2. Reaction product imaging

    Chandler, D.W. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    Over the past few years the author has investigated the photochemistry of small molecules using the photofragment imaging technique. Bond energies, spectroscopy of radicals, dissociation dynamics and branching ratios are examples of information obtained by this technique. Along with extending the technique to the study of bimolecular reactions, efforts to make the technique as quantitative as possible have been the focus of the research effort. To this end, the author has measured the bond energy of the C-H bond in acetylene, branching ratios in the dissociation of HI, the energetics of CH{sub 3}Br, CD{sub 3}Br, C{sub 2}H{sub 5}Br and C{sub 2}H{sub 5}OBr dissociation, and the alignment of the CD{sub 3} fragment from CD{sub 3}I photolysis. In an effort to extend the technique to bimolecular reactions the author has studied the reaction of H with HI and the isotopic exchange reaction between H and D{sub 2}.

  3. What Is a Reaction Rate?

    Schmitz, Guy

    2005-01-01

    The definition of reaction rate is derived and demonstrations are made for the care to be taken while using the term. Reaction rate can be in terms of a reaction property, the extent of reaction and thus it is possible to give a definition applicable in open and closed systems.

  4. Kinetics of Bio-Reactions

    Villadsen, John

    2015-01-01

    his chapter predicts the specific rates of reaction by means of a mathematical expression, the kinetics of the reaction. This expression can be derived through a mechanistic interpretation of an enzymatically catalyzed reaction, but it is essentially of empirical nature for cell reactions. The mo...

  5. Reactions to dietary tartrazine.

    David, T J

    1987-02-01

    Double blind challenges with tartrazine and benzoic acid were performed in hospital in 24 children whose parents gave a definite history of a purely behavioural immediate adverse reaction to one of these substances. The patients, whose ages ranged from 1.6 to 12.4 years, were on a diet that avoided these items, and in all there was a clear history that any lapse of the diet caused an obvious adverse behavioural reaction within two hours. In no patient was any change in behaviour noted either by the parents or the nursing staff after the administration of placebo or active substances. Twenty two patients returned to a normal diet without problems, but the parents of two children insisted on continuing the diet. While popular belief has it that additives may have harmful behavioural effects, objective verification is required to prevent overdiagnosis.

  6. Photooxidative reactions of psoralens

    Potapenko, A.Ya.; Sukhorukov, V.L.

    1984-01-01

    The mechanism and biological significance of photooxidative reactions of psoralens are reviewed. Skin-photosensitizing activities of bifunctional and monofunctional psoralens are compared. Antioxidants tocopherols and butilated hydroxytoluene inhibit photochemical reactions of psoralens responsible for induction of erythema. The same antioxidants do not inhibit PUVA-therapy of psriasis. Though psoralens can generate singlet oxygen under UVA-irradiation (315 - 400 nm), nevertheless singlet oxygen does not play significant role in 8-methoxypsoralen (8-MOP) sensitized photooxidation of tocopherol or dihydroxyphenylalanine (DOPA). SH-compounds enhance the rate of 8-MOP sensitized photooxidation of DOPA by a factor of four, simultaneously the rate of oxidation of SH-groups is enhanced many fold in the presence of DOPA. Under UVA-irradiation in organic solvents psoralens are photooxidized. Dimeric photooxidized psoralens are easily destructed in water medium, their destruction induce oxidation of unsaturated lipids and DOPA. (author)

  7. Solar nuclear reactions

    Kocharov, G

    1978-04-01

    The current state of neutrino solar astrophysics is outlined, showing the contradictions between the experimental results of solar neutrino detection and the standard solar models constructed on the basis of the star structure and development theory, which give values for high-energy neutrino fluxes considerably exceeding the upper experimental limit. A number of hypotheses interpreting the experimental results are summarized. The hypotheses are critically assessed and experiments are recommended for refining or verifying experimental data. Also dealt with are nuclear reactions in the Sun, as is the attempt to interpret the anomalous by high /sup 3/He fluxes from the Sun and the relatively small amounts of solar neutrinos and gamma quanta. The importance is emphasized of the simultaneous and complex measurement of the fluxes of neutrons, gamma radiation, and isotopes of hydrogen, helium, and boron from the Sun as indicators of nuclear reactions in the Sun.

  8. Reaction chemistry of cerium

    NONE

    1997-01-01

    It is truly ironic that a synthetic organic chemist likely has far greater knowledge of the reaction chemistry of cerium(IV) than an inorganic colleague. Cerium(IV) reagents have long since been employed as oxidants in effecting a wide variety of organic transformations. Conversely, prior to the late 1980s, the number of well characterized cerium(IV) complexes did not extend past a handful of known species. Though in many other areas, interest in the molecular chemistry of the 4f-elements has undergone an explosive growth over the last twenty years, the chemistry of cerium(IV) has for the most part been overlooked. This report describes reactions of cerium complexes and structure.

  9. Reactions to dietary tartrazine.

    David, T J

    1987-01-01

    Double blind challenges with tartrazine and benzoic acid were performed in hospital in 24 children whose parents gave a definite history of a purely behavioural immediate adverse reaction to one of these substances. The patients, whose ages ranged from 1.6 to 12.4 years, were on a diet that avoided these items, and in all there was a clear history that any lapse of the diet caused an obvious adverse behavioural reaction within two hours. In no patient was any change in behaviour noted either by the parents or the nursing staff after the administration of placebo or active substances. Twenty two patients returned to a normal diet without problems, but the parents of two children insisted on continuing the diet. While popular belief has it that additives may have harmful behavioural effects, objective verification is required to prevent overdiagnosis. PMID:3548601

  10. Hadron reaction mechanisms

    Collins, P.D.B.; Martin, A.D.

    1982-01-01

    The mechanism of hadron scattering at high energies are reviewed in such a way as to combine the ideas of the parton model and quantum chromodynamics (QCD) with Regge theory and phenomenology. After a brief introduction to QCD and the basic features of hadron scattering data, scaling and the dimensional counting rules, the parton structure of hadrons, and the parton model for large momentum transfer processes, including scaling violations are discussed. Hadronic jets and the use of parton ideas in soft scattering processes are examined, attention being paid to Regge theory and its applications in exclusive and inclusive reactions, the relationship to parton exchange being stressed. The mechanisms of hadron production which build up cross sections, and hence the underlying Regge singularities, and the possible overlap of Regge and scaling regions are discussed. It is concluded that the key to understanding hadron reaction mechanisms seems to lie in the marriage of Regge theory with QCD. (author)

  11. Nuclear reactions in astrophysics

    Cardenas, M.

    1976-01-01

    It is revised the nuclear reactions which present an interest in astrophysics regarding the explanation of some problems such as the relative quantity of the elements, the structure and evolution of the stars. The principal object of the study is the determination of the experimental possibilities in the field of astrophysics, of an accelerator Van de Graaff's 700 KeV type. Two hundred nuclear reactions approximately, were found, and nothing or very little has been done in the intervals of energy which are of interest. Since the bombardment energies and the involved sections are low in some cases, there are real possibilities, for the largest number of stars to obtain important statistical data with the above mentioned accelerator, taking some necessary precautions. (author)

  12. Photochemical reaction dynamics

    Moore, B.C. [Lawrence Berkeley Laboratory, Livermore, CA (United States)

    1993-12-01

    The purpose of the program is to develop a fundamental understanding of unimolecular and bimolecular reaction dynamics with application in combustion and energy systems. The energy dependence in ketene isomerization, ketene dissociation dynamics, and carbonyl substitution on organometallic rhodium complexes in liquid xenon have been studied. Future studies concerning unimolecular processes in ketene as well as energy transfer and kinetic studies of methylene radicals are discussed.

  13. Polyneutron Chain Reactions

    John C. Fisher

    2000-01-01

    Although helium atoms do not form molecules, a sufficiently large number will bind into a stable liquid droplet. A comparable situation is expected for neutrons, with a sufficiently large number binding into a stable droplet of neutron matter. Such polyneutron droplets can be viewed as isotopes of an element with nuclear charge Z=0, tentatively denoted neutrium, symbol Nt. Because of the relatively weak binding of neutrons compared with that of a mix of neutrons and protons, the minimum number of neutrons required for stability of a droplet is fairly large. Early estimates of ∼60 may be reduced to a dozen or so by the BCS pairing interaction. The Nt entries with N≥12 are new to the table of isotopes. Because all of them are beta-unstable, none is expected to persist as a free particle. Yet, some may occasionally be produced by means to be described below, and it is of interest to examine their decay chains and their interactions with charged nuclei to ascertain how their presence might be revealed. Although these reactions are interesting, they cannot be taken seriously without identifying a source for the initial Nt isotope that begins the chain. Here, we consider possible interactions between 16 O and A Nt. Although there is no strong interaction between them, we can expect a very weak residual attraction that can form a loosely bound 16 O A Nt nuclear molecule. This is not a compound nucleus in the usual sense because, considered as fluids, the 16 O and A Nt droplets are immiscible. For a droplet with fewer than about 60 neutrons, beta decay of A Nt is prevented by the buildup of Coulomb energy associated with transforming A Nt into A H in close proximity to 16 O. Thus, it is possible that 16 O A Nt molecules can persist indefinitely and that a few of them may be present in ordinary water as supermassive oxygen nuclei. Because the binding of these molecules is weak, the A Nt component can tunnel to an adjacent nucleus, and if the adjacent nucleus is 18 O, a

  14. Borehole heater test at KAERI Underground Research Tunnel

    Kwon, S. K.; Cho, W. J.; Jeon, S. W.

    2009-09-01

    At HLW repository, the temperature change due to the decay heat in near field can affect the hydraulic, mechanical, and chemical behaviors and influence on the repository safety. Therefore, the understanding of the thermal behavior in near field is essential for the site selection, design, as well as operation of the repository. In this study, various studies for the in situ heater test, which is for the investigation of the thermo-mechanical behavior in rock mass, were carried out. At first, similar in situ tests at foreign URLs were reviewed and summarized the major conclusions from the tests. After then an adequate design of heater, observation sensors, and data logging system were developed and installed with a consideration of the site condition and test purposes. In order to minimize the effect of hydraulic phenomenon, a relatively day zone was chosen for the in situ test. Joint distribution and characteristics in the zone were surveyed and the rock mass properties were determined with various laboratory tests. In this study, an adequate location for an in situ borehole heater test was chosen. Also a heater for the test was designed and manufactured and the sensors for measuring the rock behavior were installed. It was possible to observe that stiff joints are developed overwhelmingly in the test area from the joint survey at the tunnel wall. The major rock and rock mass properties at the test site could be determined from the thermo-mechanical laboratory tests using the rock cores retrieved from the site. The measured data were implemented in the three-dimensional computer simulation. From the modeling using FLAC3D code, it was possible to find that the heat convection through the tunnel wall can influence on temperature distribution in rock. Because of that it was necessary to installed a blocking wall to minimize the effect of ventilation system on the heater test, which is carrying out nearby the tunnel wall. The in situ borehole heater test is the first thermo-mechanical test in Korea. In the future, the results from the test will be utilized for different projects such as spent fuel storage, geothermal energy, sequestration of carbon-dioxide, and underground petroleum storage, which require the clear understanding on the thermo-mechanical behavior of rock mass

  15. Status of the atomized uranium silicide fuel development at KAERI

    Kim, C.K.; Kim, K.H.; Park, H.D.; Kuk, I.H. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-08-01

    While developing KMRR fuel fabrication technology an atomizing technique has been applied in order to eliminate the difficulties relating to the tough property of U{sub 3}Si and to take advantage of the rapid solidification effect of atomization. The comparison between the conventionally comminuted powder dispersion fuel and the atomized powder dispersion fuel has been made. As the result, the processes, uranium silicide powdering and heat treatment for U{sub 3}Si transformation, become simplified. The workability, the thermal conductivity and the thermal compatibility of fuel meat have been investigated and found to be improved due to the spherical shape of atomized powder. In this presentation the overall developments of atomized U{sub 3}Si dispersion fuel and the planned activities for applying the atomizing technique to the real fuel fabrication are described.

  16. AMO research activities and data centre in KAERI

    Rhee, Yongjoo [Laboratory for Quantum Optics, Korea Atomic Energy Research Institute (Korea, Republic of); Park, H M; Han, J M; Kim, S K

    2001-12-01

    Dr. Rhee presented data center activities, which support several experimental and theoretical atomic, molecular and optical (AMO) physical programmes. The activities are mainly for fusion science and high precision trace analysis for nuclear safety. There were also some improvements in the ALADDIN database interface at AMODS, which employ the original FORTRAN ALADDIN codes.

  17. Procedures for Decomposing a Redox Reaction into Half-Reaction

    Fishtik, Ilie; Berka, Ladislav H.

    2005-01-01

    A simple algorithm for a complete enumeration of the possible ways a redox reaction (RR) might be uniquely decomposed into half-reactions (HRs) using the response reactions (RERs) formalism is presented. A complete enumeration of the possible ways a RR may be decomposed into HRs is equivalent to a complete enumeration of stoichiometrically…

  18. Insect bite reactions

    Sanjay Singh

    2013-01-01

    Full Text Available Insects are a class of living creatures within the arthropods. Insect bite reactions are commonly seen in clinical practice. The present review touches upon the medically important insects and their places in the classification, the sparse literature on the epidemiology of insect bites in India, and different variables influencing the susceptibility of an individual to insect bites. Clinical features of mosquito bites, hypersensitivity to mosquito bites Epstein-Barr virus NK (HMB-EBV-NK disease, eruptive pseudoangiomatosis, Skeeter syndrome, papular pruritic eruption of HIV/AIDS, and clinical features produced by bed bugs, Mexican chicken bugs, assassin bugs, kissing bugs, fleas, black flies, Blandford flies, louse flies, tsetse flies, midges, and thrips are discussed. Brief account is presented of the immunogenic components of mosquito and bed bug saliva. Papular urticaria is discussed including its epidemiology, the 5 stages of skin reaction, the SCRATCH principle as an aid in diagnosis, and the recent evidence supporting participation of types I, III, and IV hypersensitivity reactions in its causation is summarized. Recent developments in the treatment of pediculosis capitis including spinosad 0.9% suspension, benzyl alcohol 5% lotion, dimethicone 4% lotion, isopropyl myristate 50% rinse, and other suffocants are discussed within the context of evidence derived from randomized controlled trials and key findings of a recent systematic review. We also touch upon a non-chemical treatment of head lice and the ineffectiveness of egg-loosening products. Knockdown resistance (kdr as the genetic mechanism making the lice nerves insensitive to permethrin is discussed along with the surprising contrary clinical evidence from Europe about efficacy of permethrin in children with head lice carrying kdr-like gene. The review also presents a brief account of insects as vectors of diseases and ends with discussion of prevention of insect bites and some

  19. Boron atom reactions

    Estes, R.; Tabacco, M.B.; Digiuseppe, T.G.; Davidovits, P.

    1982-01-01

    The reaction rates of atomic boron with various epoxides have been measured in a flow tube apparatus. The bimolecular rate constants, in units of cm 3 molecule -1 s -1 , are: 1,2-epoxypropane (8.6 x 10 -11 ), 1,2-epoxybutane (8.8 x 10 -11 ), 1,2,3,4-diepoxybutane (5.5 x 10 -11 ), 1-chloro-2,3-epoxypropane (5.7 x 10 -11 ), and 1,2-epoxy-3,3,3-trichloropropane (1.5 x 10 -11 ). (orig.)

  20. Nuclear reactions. An introduction

    Paetz gen. Schieck, Hans [Koeln Univ. (Germany). Inst. fuer Kernphysik

    2014-03-01

    Modern, self-contained introduction to the subject matter. Emphasizes the interplay between theory and experiment. Course-tested tutorial style, contains many derivations. Nuclei and nuclear reactions offer a unique setting for investigating three (and in some cases even all four) of the fundamental forces in nature. Nuclei have been shown - mainly by performing scattering experiments with electrons, muons, and neutrinos - to be extended objects with complex internal structures: constituent quarks; gluons, whose exchange binds the quarks together; sea-quarks, the ubiquitous virtual quark-antiquark pairs and, last but not least, clouds of virtual mesons, surrounding an inner nuclear region, their exchange being the source of the nucleon-nucleon interaction. The interplay between the (mostly attractive) hadronic nucleon-nucleon interaction and the repulsive Coulomb force is responsible for the existence of nuclei; their degree of stability, expressed in the details and limits of the chart of nuclides; their rich structure and the variety of their interactions. Despite the impressive successes of the classical nuclear models and of ab-initio approaches, there is clearly no end in sight for either theoretical or experimental developments as shown e.g. by the recent need to introduce more sophisticated three-body interactions to account for an improved picture of nuclear structure and reactions. Yet, it turns out that the internal structure of the nucleons has comparatively little influence on the behavior of the nucleons in nuclei, and nuclear physics - especially nuclear structure and reactions - is thus a field of science in its own right, without much recourse to subnuclear degrees of freedom. This book collects essential material that was presented in the form of lectures notes in nuclear physics courses for graduate students at the University of Cologne. It follows the course's approach, conveying the subject matter by combining experimental facts and

  1. Comparing chemical reaction networks

    Cardelli, Luca; Tribastone, Mirco; Tschaikowski, Max

    2017-01-01

    We study chemical reaction networks (CRNs) as a kernel model of concurrency provided with semantics based on ordinary differential equations. We investigate the problem of comparing two CRNs, i.e., to decide whether the solutions of a source and of a target CRN can be matched for an appropriate...... choice of initial conditions. Using a categorical framework, we extend and unify model-comparison approaches based on dynamical (semantic) and structural (syntactic) properties of CRNs. Then, we provide an algorithm to compare CRNs, running linearly in time with respect to the cardinality of all possible...... comparisons. Finally, using a prototype implementation, CAGE, we apply our results to biological models from the literature....

  2. Gravitational radiation reaction

    Tanaka, Takahiro

    2006-01-01

    We give a short personally-biased review on the recent progress in our understanding of gravitational radiation reaction acting on a point particle orbiting a black hole. The main motivation of this study is to obtain sufficiently precise gravitational waveforms from inspiraling binary compact starts with a large mass ratio. For this purpose, various new concepts and techniques have been developed to compute the orbital evolution taking into account the gravitational self-force. Combining these ideas with a few supplementary new ideas, we try to outline a path to our goal here. (author)

  3. Isotopes in oxidation reactions

    Stewart, R.

    1976-01-01

    The use of isotopes in the study of organic oxidation mechanisms is discussed. The help provided by tracer studies to demonstrate the two-equivalent path - hydride transfer, is illustrated by the examples of carbonium oxidants and the Wacker reaction. The role of kinetic isotope effects in the study of the scission of carbon-hydrogen bonds is illustrated by hydride abstraction, hydrogen atom abstraction, proton abstraction and quantum mechanical tunnelling. Isotopic studies on the oxidation of alcohols, carbonyl compounds, amines and hydrocarbons are discussed. The role of isotopes in the study of biochemical oxidation is illustrated with a discussion on nicotinamide and flavin coenzymes. (B.R.H.)

  4. Low Energy Nuclear Reactions?

    CERN. Geneva; Faccini, R.

    2014-01-01

    After an introduction to the controversial problem of Low Energy Nuclear Reactions (LENR) catalyzed by neutrons on metallic hydride surfaces we present the results of an experiment, made in collaboration with ENEA Labs in Frascati, to search neutrons from plasma discharges in electrolytic cells. The negative outcome of our experiment goes in the direction of ruling out those theoretical models expecting LENR to occur in condensed matter systems under specific conditions. Our criticism on the theoretical foundations of such models will also be presented.

  5. Nuclear reactions. An introduction

    Paetz gen. Schieck, Hans

    2014-01-01

    Modern, self-contained introduction to the subject matter. Emphasizes the interplay between theory and experiment. Course-tested tutorial style, contains many derivations. Nuclei and nuclear reactions offer a unique setting for investigating three (and in some cases even all four) of the fundamental forces in nature. Nuclei have been shown - mainly by performing scattering experiments with electrons, muons, and neutrinos - to be extended objects with complex internal structures: constituent quarks; gluons, whose exchange binds the quarks together; sea-quarks, the ubiquitous virtual quark-antiquark pairs and, last but not least, clouds of virtual mesons, surrounding an inner nuclear region, their exchange being the source of the nucleon-nucleon interaction. The interplay between the (mostly attractive) hadronic nucleon-nucleon interaction and the repulsive Coulomb force is responsible for the existence of nuclei; their degree of stability, expressed in the details and limits of the chart of nuclides; their rich structure and the variety of their interactions. Despite the impressive successes of the classical nuclear models and of ab-initio approaches, there is clearly no end in sight for either theoretical or experimental developments as shown e.g. by the recent need to introduce more sophisticated three-body interactions to account for an improved picture of nuclear structure and reactions. Yet, it turns out that the internal structure of the nucleons has comparatively little influence on the behavior of the nucleons in nuclei, and nuclear physics - especially nuclear structure and reactions - is thus a field of science in its own right, without much recourse to subnuclear degrees of freedom. This book collects essential material that was presented in the form of lectures notes in nuclear physics courses for graduate students at the University of Cologne. It follows the course's approach, conveying the subject matter by combining experimental facts and experimental

  6. Development of the On-line Acoustic Leak Detection Tool for the SFR Steam Generator Protection

    Kim, Tae-Joon; Jeong, Ji-Young; Kim, Jong-Man; Kim, Byung-Ho; Kim, Seong-O

    2007-01-01

    The successful detection of a water/steam into a sodium leak in the SFR SG (steam generator) at an early phase of a leak origin depends on the fast response and sensitivity of a leak detection system. This intention of an acoustic leak detection system is stipulated by a key impossibility of a fast detecting of an intermediate leak by the present nominal systems such as the hydrogen meter. Subject of this study is to introduce the detection performance of an on-line acoustic leak detection tool discriminated by a back-propagation neural network with a preprocessing of the 1/m Octave band analysis, and to introduce the status of an on-line development being developed with the acoustic leak detection tool(S/W) in KAERI. For a performance test, it was used with the acoustic signals for a sodium-water reaction from the injected steam into water experiments in KAERI, the acoustic signals injected from the water into the sodium obtained in IPPE, and the background noise of the PFR superheater

  7. Polymer reaction engineering, an integrated approach

    Meyer, T.; Keurentjes, J.T.F.; Meyer, T.; Keurentjes, J.T.F.

    2005-01-01

    Summary This chapter contains sections titled: Polymer Materials A Short History of Polymer Reaction Engineering The Position of Polymer Reaction Engineering Toward Integrated Polymer Reaction Engineering The Disciplines in Polymer Reaction Engineering The Future: Product-inspired Polymer Reaction

  8. Substitution reactions of technetium complexes

    Omori, T.

    1997-01-01

    Substitution reactions of a series of technetium complexes are considered in comparison with corresponding reactions of rhenium. Rhenium and technetium complexes are rather inert in substitution reactions, the latter are characterized by greater rate constants when they proceed according to dissociative mechanism. In rare cases when k Tc /k Re id little it is assumed that the reaction proceeds according to the associative mechanism. (author)

  9. The nuclear reaction matrix

    Krenciglowa, E.M.; Kung, C.L.; Kuo, T.T.S.; Osnes, E.; and Department of Physics, State University of New York at Stony Brook, Stony Brook, New York 11794)

    1976-01-01

    Different definitions of the reaction matrix G appropriate to the calculation of nuclear structure are reviewed and discussed. Qualitative physical arguments are presented in support of a two-step calculation of the G-matrix for finite nuclei. In the first step the high-energy excitations are included using orthogonalized plane-wave intermediate states, and in the second step the low-energy excitations are added in, using harmonic oscillator intermediate states. Accurate calculations of G-matrix elements for nuclear structure calculations in the Aapprox. =18 region are performed following this procedure and treating the Pauli exclusion operator Q 2 /sub p/ by the method of Tsai and Kuo. The treatment of Q 2 /sub p/, the effect of the intermediate-state spectrum and the energy dependence of the reaction matrix are investigated in detail. The present matrix elements are compared with various matrix elements given in the literature. In particular, close agreement is obtained with the matrix elements calculated by Kuo and Brown using approximate methods

  10. The redox-Mannich reaction.

    Chen, Weijie; Seidel, Daniel

    2014-06-06

    A complement to the classic three-component Mannich reaction, the redox-Mannich reaction, utilizes the same starting materials but incorporates an isomerization step that enables the facile preparation of ring-substituted β-amino ketones. Reactions occur under relatively mild conditions and are facilitated by benzoic acid.

  11. Reaction Decoder Tool (RDT): extracting features from chemical reactions.

    Rahman, Syed Asad; Torrance, Gilliean; Baldacci, Lorenzo; Martínez Cuesta, Sergio; Fenninger, Franz; Gopal, Nimish; Choudhary, Saket; May, John W; Holliday, Gemma L; Steinbeck, Christoph; Thornton, Janet M

    2016-07-01

    Extracting chemical features like Atom-Atom Mapping (AAM), Bond Changes (BCs) and Reaction Centres from biochemical reactions helps us understand the chemical composition of enzymatic reactions. Reaction Decoder is a robust command line tool, which performs this task with high accuracy. It supports standard chemical input/output exchange formats i.e. RXN/SMILES, computes AAM, highlights BCs and creates images of the mapped reaction. This aids in the analysis of metabolic pathways and the ability to perform comparative studies of chemical reactions based on these features. This software is implemented in Java, supported on Windows, Linux and Mac OSX, and freely available at https://github.com/asad/ReactionDecoder : asad@ebi.ac.uk or s9asad@gmail.com. © The Author 2016. Published by Oxford University Press.

  12. Nuclear reactions an introduction

    Paetz gen. Schieck, Hans

    2014-01-01

    Nuclei and nuclear reactions offer a unique setting for investigating three (and in some cases even all four) of the fundamental forces in nature. Nuclei have been shown – mainly by performing scattering experiments with electrons, muons, and neutrinos – to be extended objects with complex internal structures: constituent quarks; gluons, whose exchange binds the quarks together; sea-quarks, the ubiquitous virtual quark-antiquark pairs and, last but not least, clouds of virtual mesons, surrounding an inner nuclear region, their exchange being the source of the nucleon-nucleon interaction.   The interplay between the (mostly attractive) hadronic nucleon-nucleon interaction and the repulsive Coulomb force is responsible for the existence of nuclei; their degree of stability, expressed in the details and limits of the chart of nuclides; their rich structure and the variety of their interactions. Despite the impressive successes of the classical nuclear models and of ab-initio approaches, there is clearly no ...

  13. Laser induced nuclear reactions

    Ledingham, Ken; McCanny, Tom; Graham, Paul; Fang Xiao; Singhal, Ravi; Magill, Joe; Creswell, Alan; Sanderson, David; Allott, Ric; Neely, David; Norreys, Peter; Santala, Marko; Zepf, Matthew; Watts, Ian; Clark, Eugene; Krushelnick, Karl; Tatarakis, Michael; Dangor, Bucker; Machecek, Antonin; Wark, Justin

    1998-01-01

    Dramatic improvements in laser technology since 1984 have revolutionised high power laser technology. Application of chirped-pulse amplification techniques has resulted in laser intensities in excess of 10 19 W/cm 2 . In the mid to late eighties, C. K. Rhodes and K. Boyer discussed the possibility of shining laser light of this intensity onto solid surfaces and to cause nuclear transitions. In particular, irradiation of a uranium target could induce electro- and photofission in the focal region of the laser. In this paper it is shown that μCi of 62 Cu can be generated via the (γ,n) reaction by a laser with an intensity of about 10 19 Wcm -2

  14. Nuclear reactions in astrophysics

    Arnould, M.; Rayet, M.

    1990-01-01

    At all times and at all astrophysical scales, nuclear reactions have played and continue to play a key role. This concerns the energetics as well as the production of nuclides (nucleosynthesis). After a brief review of the observed composition of various objects in the universe, and especially of the solar system, the basic ingredients that are required in order to build up models for the chemical evolution of galaxies are sketched. Special attention is paid to the evaluation of the stellar yields through an overview of the important burning episodes and nucleosynthetic processes that can develop in non-exploding or exploding stars. Emphasis is put on the remaining astrophysical and nuclear physics uncertainties that hamper a clear understanding of the observed characteristics, and especially compositions, of a large variety of astrophysical objects

  15. Ion-Molecule Reaction Dynamics.

    Meyer, Jennifer; Wester, Roland

    2017-05-05

    We review the recent advances in the investigation of the dynamics of ion-molecule reactions. During the past decade, the combination of single-collision experiments in crossed ion and neutral beams with the velocity map ion imaging detection technique has enabled a wealth of studies on ion-molecule reactions. These methods, in combination with chemical dynamics simulations, have uncovered new and unexpected reaction mechanisms, such as the roundabout mechanism and the subtle influence of the leaving group in anion-molecule nucleophilic substitution reactions. For this important class of reactions, as well as for many fundamental cation-molecule reactions, the information obtained with crossed-beam imaging is discussed. The first steps toward understanding micro-solvation of ion-molecule reaction dynamics are presented. We conclude with the presentation of several interesting directions for future research.

  16. Reaction mechanisms of metal complexes

    Hay, R W

    2000-01-01

    This text provides a general background as a course module in the area of inorganic reaction mechanisms, suitable for advanced undergraduate and postgraduate study and/or research. The topic has important research applications in the metallurgical industry and is of interest in the science of biochemistry, biology, organic, inorganic and bioinorganic chemistry. In addition to coverage of substitution reactions in four-, five- and six-coordinate complexes, the book contains further chapters devoted to isomerization and racemization reactions, to the general field of redox reactions, and to the reactions of coordinated ligands. It is relevant in other fields such as organic, bioinorganic and biological chemistry, providing a bridge to organic reaction mechanisms. The book also contains a chapter on the kinetic background to the subject with many illustrative examples which should prove useful to those beginning research. Provides a general background as a course module in the area of inorganic reaction mechanis...

  17. Extent of reaction in open systems with multiple heterogeneous reactions

    Friedly, John C.

    1991-01-01

    The familiar batch concept of extent of reaction is reexamined for systems of reactions occurring in open systems. Because species concentrations change as a result of transport processes as well as reactions in open systems, the extent of reaction has been less useful in practice in these applications. It is shown that by defining the extent of the equivalent batch reaction and a second contribution to the extent of reaction due to the transport processes, it is possible to treat the description of the dynamics of flow through porous media accompanied by many chemical reactions in a uniform, concise manner. This approach tends to isolate the reaction terms among themselves and away from the model partial differential equations, thereby enabling treatment of large problems involving both equilibrium and kinetically controlled reactions. Implications on the number of coupled partial differential equations necessary to be solved and on numerical algorithms for solving such problems are discussed. Examples provided illustrate the theory applied to solute transport in groundwater flow.

  18. Nuclear reactions as structure probes

    Fernandez, Bernard; Cugnon, Joseph; Roussel-Chomaz, Patricia; Sparenberg, Jean-Marc; Oliveira Santos, Francois de; Bauge, Eric; Poves, Alfredo; Keeley, Nicholas; Simenel, Cedric; Avez, Benoit; Lacroix, Denis; Baye, Daniel; Cortina-Gil, Dolores; Pons, Alexandre

    2007-09-01

    This publication gathers courses which aim at giving a view on new experiments which are performed by using radioactive beams, notably low intensity beams, in different accelerators, and allow the structure of very exotic nuclei to be characterized. Experimental as well as theoretical aspects are thus addressed. The contributions propose: a brief history of nuclear reactions and of instruments used to study them from the discovery of nucleus to the DWBA (Distorted Wave Born Approximation); an overview of nuclear reactions; experimental techniques; the theory of collisions at low energy; resonant elastic scattering, inelastic scattering and astrophysical reactions; to probe nuclear structure with nucleons; shell model and spectroscopic factors; analysis of transfer reactions and determination of spectroscopic factors; microscopic approaches of nuclear dynamics; theoretical aspects of dissociation reactions; experimental aspects of knockout reactions; research in oenology with the chemical characterisation of defective ageing of dry white wines

  19. Characterising Complex Enzyme Reaction Data.

    Handan Melike Dönertaş

    Full Text Available The relationship between enzyme-catalysed reactions and the Enzyme Commission (EC number, the widely accepted classification scheme used to characterise enzyme activity, is complex and with the rapid increase in our knowledge of the reactions catalysed by enzymes needs revisiting. We present a manual and computational analysis to investigate this complexity and found that almost one-third of all known EC numbers are linked to more than one reaction in the secondary reaction databases (e.g., KEGG. Although this complexity is often resolved by defining generic, alternative and partial reactions, we have also found individual EC numbers with more than one reaction catalysing different types of bond changes. This analysis adds a new dimension to our understanding of enzyme function and might be useful for the accurate annotation of the function of enzymes and to study the changes in enzyme function during evolution.

  20. The Glaser–Hay reaction

    Vilhelmsen, Mie Højer; Jensen, Jonas; Tortzen, Christian

    2013-01-01

    The oxidative Glaser–Hay coupling of two terminal alkynes to furnish a butadiyne is a key reaction for acetylenic scaffolding. Although the reaction is performed under rather simple conditions [CuCl/TMEDA/O2 (air)], the mechanism is still under debate. Herein we present detailed studies...... on the scope of this reaction by using both 13C NMR and UV/Vis spectroscopic methods. The former method was used to study the kinetics of the coupling of aryl-substituted alkynes as the aryl carbon resonances of the reactants and products have similar NOEs and relaxation times. The reaction was found...... to be zero-order with respect to the terminal alkyne reactant under standard preparative conditions. Moreover, as the reaction proceeded, a clear change to slower reaction kinetics was observed, but it was still apparently zero-order. The onset of this change was found to depend on the catalyst loading...

  1. The Paterno-Buchi reaction

    Brogaard, Rasmus Yding; Schalk, Oliver; Boguslavskiy, Andrey E.

    2012-01-01

    The Paternò-Büchi (PB) reaction between an excited carbonyl compound and an alkene has been widely studied, but so far little is known about the excited-state dynamics of the reaction. In this investigation, we used a compound in which a formyl and a vinyl group are attached to a [2.......2]paracyclophane in order to obtain a model system in pre-reactive conformation for the PB reaction. We studied the excited-state dynamics of the isolated molecule in a molecular beam using femtosecond time-resolved photoelectron spectroscopy and ab initio calculations. The results show that inter-system crossing...... within two picoseconds competes efficiently with the reaction in the singlet manifold. Thus, the PB reaction in this model system takes place in the triplet state on a time scale of nanoseconds. This result stresses the importance of triplet states in the excited-state pathway of the PB reaction...

  2. Limits for Stochastic Reaction Networks

    Cappelletti, Daniele

    Reaction systems have been introduced in the 70s to model biochemical systems. Nowadays their range of applications has increased and they are fruitfully used in dierent elds. The concept is simple: some chemical species react, the set of chemical reactions form a graph and a rate function...... is associated with each reaction. Such functions describe the speed of the dierent reactions, or their propensities. Two modelling regimes are then available: the evolution of the dierent species concentrations can be deterministically modelled through a system of ODE, while the counts of the dierent species...... at a certain time are stochastically modelled by means of a continuous-time Markov chain. Our work concerns primarily stochastic reaction systems, and their asymptotic properties. In Paper I, we consider a reaction system with intermediate species, i.e. species that are produced and fast degraded along a path...

  3. Metal-free bioconjugation reactions.

    van Berkel, Sander S; van Delft, Floris L

    2013-01-01

    The recent strategy to apply chemical reactions to address fundamental biological questions has led to the emergence of entirely new conjugation reactions that are fast and irreversible, yet so mild and selective that they can be performed even in living cells or organisms. These so-called bioorthogonal reactions open novel avenues, not only in chemical biology research, but also in many other life sciences applications, including the modulation of biopharmaceuticals by site-specific modification approaches.

  4. Multistep processes in nuclear reactions

    Hodgson, P.E.

    1988-01-01

    The theories of nuclear reactions are reviewed with particular attention to the recent work on multistep processes. The evidence for compound nucleus and direct interaction reactions is described together with the results of comparisons between theories and experimental data. These theories have now proved inadequate, and there is evidence for multistep processes that take place after the initial direct stage but long before the attainment of the statistical equilibrium characteristic of compound nucleus processes. The theories of these reactions are described and it is shown how they can account for the experimental data and thus give a comprehensive understanding of nuclear reactions. (author)

  5. Progress in microscopic direct reaction modeling of nucleon induced reactions

    Dupuis, M.; Bauge, E.; Hilaire, S.; Lechaftois, F.; Peru, S.; Pillet, N.; Robin, C. [CEA, DAM, DIF, Arpajon (France)

    2015-12-15

    A microscopic nuclear reaction model is applied to neutron elastic and direct inelastic scatterings, and pre-equilibrium reaction. The JLM folding model is used with nuclear structure information calculated within the quasi-particle random phase approximation implemented with the Gogny D1S interaction. The folding model for direct inelastic scattering is extended to include rearrangement corrections stemming from both isoscalar and isovector density variations occurring during a transition. The quality of the predicted (n,n), (n,n{sup '}), (n,xn) and (n,n{sup '}γ) cross sections, as well as the generality of the present microscopic approach, shows that it is a powerful tool that can help improving nuclear reactions data quality. Short- and long-term perspectives are drawn to extend the present approach to more systems, to include missing reactions mechanisms, and to consistently treat both structure and reaction problems. (orig.)

  6. Reaction mechanisms in zeolite catalysis

    Rozanska, X.; Santen, van R.A.; Auerbach, S.C.; Carrado, K.A.; Dutta, P.D.

    2003-01-01

    A review; described are the most basic mechanistic reaction steps that are induced by zeolite catalysts. Details on the zeolitic properties that are relevant to mol. reactivity are also provided. The theor. methods and models at hand to allow the investigation of these reaction steps and that have

  7. Engineering reactors for catalytic reactions

    Extensive studies have been conducted to establish sound basis for design and engineering of reactors for practising such catalytic reactions and for realizing improvements in reactor performance. In this article, application of recent (and not so recent) developments in engineering reactors for catalytic reactions is ...

  8. Sodium concrete reaction - Structural considerations

    Ferskakis, G.N.

    1984-01-01

    An overview of the sodium concrete reaction phenomenon, with emphasis on structural considerations, is presented. Available test results for limestone, basalt, and magnetite concrete with various test article configurations are reviewed. Generally, tests indicate reaction is self limiting before all sodium is used. Uncertainties, however, concerning the mechanism for penetration of sodium into concrete have resulted in different theories about a reaction model. Structural behavior may be significant in the progression of the reaction due to thermal-structuralchemical interactions involving tensile cracking, compressive crushing, or general deterioration of concrete and the exposure of fresh concrete surfaces to react with sodium. Structural behavior of test articles and potential factors that could enhance the progression of the reaction are discussed

  9. STUDIES ON ENDOTHELIAL REACTIONS

    Foot, Nathan Chandler

    1923-01-01

    operative. On the other hand, there may be an increase in the phagocytic activity of the endothelium of the sinusoids which might take up more bacteria under these changed conditions. Several investigators have claimed, recently, that there is an increased activity of the liver endothelium following splenectomy, their experiments being directed chiefly toward determining the fate of the erythrocytes. Pearce (1918) in reporting the effects of experimental splenectomy in dogs, states that there are definite compensatory changes in the lymph nodes, in the form of an increased proliferation of endothelial phagocytes, and that the stellate cells of the liver sinusoids often show a similar compensatory increase in number. In both cases the cells are, apparently, formed in situ rather than transported to the organs. He says: ‘Such findings suggest the development of a compensatory function on the part of the lymph-nodes and possibly the liver,’ and suggests that, in times of stress ‘the stellate cells of the liver thus assume, in part at least, the function of destroying red blood-corpuscles by phagocytosis.’ Incidentally, he presents an excellent discussion of the history and subject of splenectomy. Motohashi (1922) reports a great increase in the hemophagic power of the hepatic endothelium and an increase in the number of endothelial elements, after some 45 days following splenectomy in rabbits. Nishikawa and Takagi (1922) have observed similar phenomena with white rats, the Kupffer cells taking up erythrocytes in large numbers in splenectomized animals, whereas controls never show similar propensities on the part of these cells. It may be that different substances cause different reactions on the part of the hepatic endothelium. Contributory Experiment.—A side experiment was performed with five rabbits, two splenectomized and three controls, into which uniform doses of pneumococci were injected intravenously. They all died of septicemia after a few days. The results

  10. Dechlorinating reaction of organic chlorides

    Yahata, Taneaki; Kihara, Shinji [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Ohuchi, Misao

    1996-06-01

    Dechlorination has been examined by the reaction between iron, aluminum powder or CaO and organic chlorides such as C{sub 2}HCl{sub 3} and CH{sub 2}Cl{sub 2}. Progress of the reaction was analyzed with mass spectrometer. The reaction between iron and organic chloride was rapidly occurred at the temperature between 350 and 440degC in an atmosphere of argon. Above 380degC, more than 99.5% of C{sub 2}HCl{sub 3} was decomposed within approximately 100 minutes. At 440degC, approximately 60% of C{sub 2}HCl{sub 3} was decomposed by the reaction with aluminium powder within approximately 100 minutes. At 440degC, reaction between C{sub 2}HCl{sub 3} and CaO powder were occurred rapidly in an atmosphere of argon to form CaCl{sub 2} and free carbon. Also in an atmosphere of air, nearly the same result was obtained. In this reaction, CaCl{sub 2}, CO and CO{sub 2} were formed. CH{sub 2}Cl{sub 2} was also decomposed by the reaction with iron at the temperature between 380 and 440degC. In the reaction, FeCl{sub 2}, carbon and hydrogen were formed. CH{sub 3}{sup +} and CH{sub 4} were observed during the dechlorinating reaction of CH{sub 2}Cl{sub 2}. Variation in particle size of iron powder such as 100, 150 and 250 mesh did not affect the reaction rate. (author)

  11. Fusion chain reaction - a chain reaction with charged particles

    Peres, A.; Shvarts, D.

    1975-01-01

    When a DT-plasma is compressed to very high density, the particles resulting from nuclear reactions give their energy mostly to D and T ions, by nuclear collisions, rather than to electrons as usual. Fusion can thus proceed as a chain reaction, without the need of thermonuclear temperatures. In this paper, we derive relations for the suprathermal ion population created by a fusion reaction. Numerical integration of these equations shows that a chain reaction can proceed in a cold infinite DT-plasma at densities above 8.4x10 27 ions.cm -3 . Seeding the plasma with a small amount of 6 Li reduces the critical density to 7.2x10 27 ions.cm -3 (140000times the normal solid density). (author)

  12. Thermally multiplexed polymerase chain reaction.

    Phaneuf, Christopher R; Pak, Nikita; Saunders, D Curtis; Holst, Gregory L; Birjiniuk, Joav; Nagpal, Nikita; Culpepper, Stephen; Popler, Emily; Shane, Andi L; Jerris, Robert; Forest, Craig R

    2015-07-01

    Amplification of multiple unique genetic targets using the polymerase chain reaction (PCR) is commonly required in molecular biology laboratories. Such reactions are typically performed either serially or by multiplex PCR. Serial reactions are time consuming, and multiplex PCR, while powerful and widely used, can be prone to amplification bias, PCR drift, and primer-primer interactions. We present a new thermocycling method, termed thermal multiplexing, in which a single heat source is uniformly distributed and selectively modulated for independent temperature control of an array of PCR reactions. Thermal multiplexing allows amplification of multiple targets simultaneously-each reaction segregated and performed at optimal conditions. We demonstrate the method using a microfluidic system consisting of an infrared laser thermocycler, a polymer microchip featuring 1 μl, oil-encapsulated reactions, and closed-loop pulse-width modulation control. Heat transfer modeling is used to characterize thermal performance limitations of the system. We validate the model and perform two reactions simultaneously with widely varying annealing temperatures (48 °C and 68 °C), demonstrating excellent amplification. In addition, to demonstrate microfluidic infrared PCR using clinical specimens, we successfully amplified and detected both influenza A and B from human nasopharyngeal swabs. Thermal multiplexing is scalable and applicable to challenges such as pathogen detection where patients presenting non-specific symptoms need to be efficiently screened across a viral or bacterial panel.

  13. Palladium-catalyzed coupling reactions

    Molnár, Árpád

    2013-01-01

    This handbook and ready reference brings together all significant issues of practical importance for interested readers in one single volume. While covering homogeneous and heterogeneous catalysis, the text is unique in focusing on such important aspects as using different reaction media, microwave techniques or catalyst recycling. It also provides a comprehensive treatment of modern-day coupling reactions and emphasizes those topics that show potential for future development, such as continuous flow systems, water as a reaction medium, and catalyst immobilization, among others. With i

  14. Catalytic Organometallic Reactions of Ammonia

    Klinkenberg, Jessica L.

    2012-01-01

    Until recently, ammonia had rarely succumbed to catalytic transformations with homogeneous catalysts, and the development of such reactions that are selective for the formation of single products under mild conditions has encountered numerous challenges. However, recently developed catalysts have allowed several classes of reactions to create products with nitrogen-containing functional groups from ammonia. These reactions include hydroaminomethylation, reductive amination, alkylation, allylic substitution, hydroamination, and cross-coupling. This Minireview describes examples of these processes and the factors that control catalyst activity and selectivity. PMID:20857466

  15. Basic reactions induced by radiation

    Charlesby, A.

    1980-01-01

    This paper summarises some of the basic reactions resulting from exposure to high energy radiation. In the initial stages energy is absorbed, but not necessarily at random, giving radical and ion species which may then react to promote the final chemical change. However, it is possible to intervene at intermediate stages to modify or reduce the radiation effect. Under certain conditions enhanced reactions are also possible. Several expressions are given to calculate radiation yield in terms of energy absorbed. Some analogies between radiation-induced reactions in polymers, and those studied in radiobiology are outlined. (author)

  16. Chemical potential and reaction electronic flux in symmetry controlled reactions.

    Vogt-Geisse, Stefan; Toro-Labbé, Alejandro

    2016-07-15

    In symmetry controlled reactions, orbital degeneracies among orbitals of different symmetries can occur along a reaction coordinate. In such case Koopmans' theorem and the finite difference approximation provide a chemical potential profile with nondifferentiable points. This results in an ill-defined reaction electronic flux (REF) profile, since it is defined as the derivative of the chemical potential with respect to the reaction coordinate. To overcome this deficiency, we propose a new way for the calculation of the chemical potential based on a many orbital approach, suitable for reactions in which symmetry is preserved. This new approach gives rise to a new descriptor: symmetry adapted chemical potential (SA-CP), which is the chemical potential corresponding to a given irreducible representation of a symmetry group. A corresponding symmetry adapted reaction electronic flux (SA-REF) is also obtained. Using this approach smooth chemical potential profiles and well defined REFs are achieved. An application of SA-CP and SA-REF is presented by studying the Cs enol-keto tautomerization of thioformic acid. Two SA-REFs are obtained, JA'(ξ) and JA'' (ξ). It is found that the tautomerization proceeds via an in-plane delocalized 3-center 4-electron O-H-S hypervalent bond which is predicted to exist only in the transition state (TS) region. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  17. Experimental Study of Serpentinization Reactions

    Cohen, B. A.; Brearley, A. J.; Ganguly, J.; Liermann, H.-P.; Keil, K.

    2004-01-01

    Current carbonaceous chondrite parent-body thermal models [1-3] produce scenarios that are inconsistent with constraints on aqueous alteration conditions based on meteorite mineralogical evidence, such as phase stability relationships within the meteorite matrix minerals [4] and isotope equilibration arguments [5, 6]. This discrepancy arises principally because of the thermal runaway effect produced by silicate hydration reactions (here loosely called serpentinization, as the principal products are serpentine minerals), which are so exothermic as to produce more than enough heat to melt more ice and provide a self-sustaining chain reaction. One possible way to dissipate the heat of reaction is to use a very small parent body [e.g., 2] or possibly a rubble pile model. Another possibility is to release this heat more slowly, which depends on the alteration reaction path and kinetics.

  18. Method for conducting exothermic reactions

    Smith, L. Jr.; Hearn, D.; Jones, E.M. Jr.

    1993-01-05

    A liquid phase process for oligomerization of C[sub 4] and C[sub 5] isoolefins or the etherification thereof with C[sub 1] to C[sub 6] alcohols wherein the reactants are contacted in a reactor with a fixed bed acid cation exchange resin catalyst at an LHSV of 5 to 20, pressure of 0 to 400 psig and temperature of 120 to 300 F. wherein the improvement is the operation of the reactor at a pressure to maintain the reaction mixture at its boiling point whereby at least a portion but less than all of the reaction mixture is vaporized. By operating at the boiling point and allowing a portion of the reaction mixture to vaporize, the exothermic heat of reaction is dissipated by the formation of more boil up and the temperature in the reactor is controlled.

  19. Analysis of kinetic reaction mechanisms

    Turányi, Tamás

    2014-01-01

    Chemical processes in many fields of science and technology, including combustion, atmospheric chemistry, environmental modelling, process engineering, and systems biology, can be described by detailed reaction mechanisms consisting of numerous reaction steps. This book describes methods for the analysis of reaction mechanisms that are applicable in all these fields. Topics addressed include: how sensitivity and uncertainty analyses allow the calculation of the overall uncertainty of simulation results and the identification of the most important input parameters, the ways in which mechanisms can be reduced without losing important kinetic and dynamic detail, and the application of reduced models for more accurate engineering optimizations. This monograph is invaluable for researchers and engineers dealing with detailed reaction mechanisms, but is also useful for graduate students of related courses in chemistry, mechanical engineering, energy and environmental science and biology.

  20. Drug Reactions in Oral Mucosa

    Emine Derviş

    2012-12-01

    Full Text Available Both immunologic and nonimmunologic drug reactions can be seen in oral mucosa. Since considerable number of these reactions heals spontaneously without being noticed by the patients, exact frequency of the lesions is unknown. Most common lesions are xerostomia, taste disorders, mucosal ulcerations and edema. In this article, oral lesions resulting from drug intake similar to those from oral lesions of local and systemic diseases, and diagnostic problems caused by these similarities, have been reviewed.

  1. Thermodynamics of random reaction networks.

    Jakob Fischer

    Full Text Available Reaction networks are useful for analyzing reaction systems occurring in chemistry, systems biology, or Earth system science. Despite the importance of thermodynamic disequilibrium for many of those systems, the general thermodynamic properties of reaction networks are poorly understood. To circumvent the problem of sparse thermodynamic data, we generate artificial reaction networks and investigate their non-equilibrium steady state for various boundary fluxes. We generate linear and nonlinear networks using four different complex network models (Erdős-Rényi, Barabási-Albert, Watts-Strogatz, Pan-Sinha and compare their topological properties with real reaction networks. For similar boundary conditions the steady state flow through the linear networks is about one order of magnitude higher than the flow through comparable nonlinear networks. In all networks, the flow decreases with the distance between the inflow and outflow boundary species, with Watts-Strogatz networks showing a significantly smaller slope compared to the three other network types. The distribution of entropy production of the individual reactions inside the network follows a power law in the intermediate region with an exponent of circa -1.5 for linear and -1.66 for nonlinear networks. An elevated entropy production rate is found in reactions associated with weakly connected species. This effect is stronger in nonlinear networks than in the linear ones. Increasing the flow through the nonlinear networks also increases the number of cycles and leads to a narrower distribution of chemical potentials. We conclude that the relation between distribution of dissipation, network topology and strength of disequilibrium is nontrivial and can be studied systematically by artificial reaction networks.

  2. Thermodynamics of random reaction networks.

    Fischer, Jakob; Kleidon, Axel; Dittrich, Peter

    2015-01-01

    Reaction networks are useful for analyzing reaction systems occurring in chemistry, systems biology, or Earth system science. Despite the importance of thermodynamic disequilibrium for many of those systems, the general thermodynamic properties of reaction networks are poorly understood. To circumvent the problem of sparse thermodynamic data, we generate artificial reaction networks and investigate their non-equilibrium steady state for various boundary fluxes. We generate linear and nonlinear networks using four different complex network models (Erdős-Rényi, Barabási-Albert, Watts-Strogatz, Pan-Sinha) and compare their topological properties with real reaction networks. For similar boundary conditions the steady state flow through the linear networks is about one order of magnitude higher than the flow through comparable nonlinear networks. In all networks, the flow decreases with the distance between the inflow and outflow boundary species, with Watts-Strogatz networks showing a significantly smaller slope compared to the three other network types. The distribution of entropy production of the individual reactions inside the network follows a power law in the intermediate region with an exponent of circa -1.5 for linear and -1.66 for nonlinear networks. An elevated entropy production rate is found in reactions associated with weakly connected species. This effect is stronger in nonlinear networks than in the linear ones. Increasing the flow through the nonlinear networks also increases the number of cycles and leads to a narrower distribution of chemical potentials. We conclude that the relation between distribution of dissipation, network topology and strength of disequilibrium is nontrivial and can be studied systematically by artificial reaction networks.

  3. 'Sum rules' for preequilibrium reactions

    Hussein, M.S.

    1981-03-01

    Evidence that suggests a correct relationship between the optical transmission matrix, P, and the several correlation widths, gamma sub(n), found in nsmission matrix, P, and the several correlation widths, n, found in multistep compound (preequilibrium) nuclear reactions, is presented. A second sum rule is also derived within the shell model approach to nuclear reactions. Indications of the potential usefulness of the sum rules in preequilibrium studies are given. (Author) [pt

  4. Medium effects in direct reactions

    Karakoc, M; Bertulani, C

    2013-01-01

    We discuss medium corrections of the nucleon-nucleon (NN) cross sections and their influence on direct reactions at intermediate energies ≳50 MeV/nucleon. The results obtained with free NN cross sections are compared with those obtained with a geometrical treatment of Pauli-blocking and Dirac-Bruecker methods. We show that medium corrections may lead to sizable modifications for collisions at intermediate energies and that they are more pronounced in reactions involving weakly bound nuclei.

  5. Reciprocity theory of homogeneous reactions

    Agbormbai, Adolf A.

    1990-03-01

    The reciprocity formalism is applied to the homogeneous gaseous reactions in which the structure of the participating molecules changes upon collision with one another, resulting in a change in the composition of the gas. The approach is applied to various classes of dissociation, recombination, rearrangement, ionizing, and photochemical reactions. It is shown that for the principle of reciprocity to be satisfied it is necessary that all chemical reactions exist in complementary pairs which consist of the forward and backward reactions. The backward reaction may be described by either the reverse or inverse process. The forward and backward processes must satisfy the same reciprocity equation. Because the number of dynamical variables is usually unbalanced on both sides of a chemical equation, it is necessary that this balance be established by including as many of the dynamical variables as needed before the reciprocity equation can be formulated. Statistical transformation models of the reactions are formulated. The models are classified under the titles free exchange, restricted exchange and simplified restricted exchange. The special equations for the forward and backward processes are obtained. The models are consistent with the H theorem and Le Chatelier's principle. The models are also formulated in the context of the direct simulation Monte Carlo method.

  6. Reactions of stabilized Criegee Intermediates

    Vereecken, Luc; Harder, Hartwig; Novelli, Anna

    2014-05-01

    Carbonyl oxides (Criegee intermediates) were proposed as key intermediates in the gas phase ozonolysis of alkenes in 1975 by Rudolf Criegee. Despite the importance of ozonolysis in atmospheric chemistry, direct observation of these intermediates remained elusive, with only indirect experimental evidence for their role in the oxidation of hydrocarbons, e.g. through scavenging experiments. Direct experimental observation of stabilized CI has only been achieved since 2008. Since then, a concerted effort using experimental and theoretical means is in motion to characterize the chemistry and kinetics of these reactive intermediates. We present the results of theoretical investigations of the chemistry of Criegee intermediates with a series of coreactants which may be of importance in the atmosphere, in experimental setups, or both. This includes the CI+CI cross-reaction, which proceeds with a rate coefficient near the collision limit and can be important in experimental conditions. The CI + alkene reactions show strong dependence of the rate coefficient depending on the coreactants, but is generally found to be rather slow. The CI + ozone reaction is sufficiently fast to occur both in experiment and the free troposphere, and acts as a sink for CI. The reaction of CI with hydroperoxides, ROOH, is complex, and leads both to the formation of oligomers, as to the formation of reactive etheroxides, with a moderately fast rate coefficient. The importance of these reactions is placed in the context of the reaction conditions in different atmospheric environments ranging from unpolluted to highly polluted.

  7. Nuclear Reactions for Astrophysics and Other Applications

    Escher, J E; Burke, J T; Dietrich, F S; Scielzo, N D; Ressler, J J

    2011-03-01

    Cross sections for compound-nuclear reactions are required for many applications. The surrogate nuclear reactions method provides an indirect approach for determining cross sections for reactions on unstable isotopes, which are difficult or impossible to measure otherwise. Current implementations of the method provide useful cross sections for (n,f) reactions, but need to be improved upon for applications to capture reactions.

  8. Reaction time for trimolecular reactions in compartment-based reaction-diffusion models

    Li, Fei; Chen, Minghan; Erban, Radek; Cao, Yang

    2018-05-01

    Trimolecular reaction models are investigated in the compartment-based (lattice-based) framework for stochastic reaction-diffusion modeling. The formulae for the first collision time and the mean reaction time are derived for the case where three molecules are present in the solution under periodic boundary conditions. For the case of reflecting boundary conditions, similar formulae are obtained using a computer-assisted approach. The accuracy of these formulae is further verified through comparison with numerical results. The presented derivation is based on the first passage time analysis of Montroll [J. Math. Phys. 10, 753 (1969)]. Montroll's results for two-dimensional lattice-based random walks are adapted and applied to compartment-based models of trimolecular reactions, which are studied in one-dimensional or pseudo one-dimensional domains.

  9. Exchange Reactions. Proceedings of the Symposium on Exchange Reactions

    1965-01-01

    The mechanisms and kinetics of chemical reactions are of great interest to chemists. The study of exchange reactions in particular helps to shed light on the dynamics of chemical change, providing an insight into the structures and the reactivities of the chemical species involved. The main theme of this meeting was the subject of oxidation-reduction reactions in which the net result is the transfer of one or more electrons between the different oxidation states of the same element. Other studies reported included the transfer of protons, atoms, complex ligands or organic radicals between molecules. Heterogeneous exchange, which is of importance in many cases of catalytic action, was also considered. For a long time isotopic tracers have formed the most convenient means of studying exchange reactions and today a considerable amount of work continues to be done with their aid. Consequently, several papers presented at this Symposium reported on work carried out by purely radiochemical tracer methods. In recognition, however, of the important role which nuclear magnetic resonance and electron spin resonance play in this field, in particular in the study of fast reactions, a number of reports on investigations in which these techniques had been used was included in the programme. By kind invitation of the United States Government the Symposium on Exchange Reactions was held from 31 May to 4 June at the Brookhaven National Laboratory, Upton, Long Island, N.Y., USA. It was attended by 46 participants from nine countries and one inter-governmental organization. The publication of these Proceedings makes the contents of the papers and the discussion available to a wider audience

  10. A comprehensive survey of nuclear reactions; Panorama des reactions nucleaires

    Cugnon, J. [Liege Univ., IFPA, AGO Dept. (Belgium)

    2007-07-01

    The various mechanisms of nuclear reactions are surveyed and classified in different regimes, based on the notions of coherent mechanisms and hard versus soft processes. The emphasis is put on the concepts at the basis of the understanding of these regimes and on the elements of nuclear structure which are involved in these different regimes, as well as the on the possibility of extracting this information. Due to lack of space and for pedagogical reasons, the discussion is limited to nucleon-induced and light-ion-induced reactions. However, a few remarks are given concerning some specific probes, such as weakly bound projectiles or neutron-rich nuclei. (author)

  11. SOLVENTLESS MIGRATORY-INSERTION REACTIONS OF ...

    Preferred Customer

    The product formed by reaction of an alkyl or aryl cyclopentadienyl metal carbonyl .... (as also observed from the NMR tube experiments) that the solventless reaction between ... As can be seen from Figure 3, the reaction rate in the melt.

  12. Biomarkers of adverse drug reactions.

    Carr, Daniel F; Pirmohamed, Munir

    2018-02-01

    Adverse drug reactions can be caused by a wide range of therapeutics. Adverse drug reactions affect many bodily organ systems and vary widely in severity. Milder adverse drug reactions often resolve quickly following withdrawal of the casual drug or sometimes after dose reduction. Some adverse drug reactions are severe and lead to significant organ/tissue injury which can be fatal. Adverse drug reactions also represent a financial burden to both healthcare providers and the pharmaceutical industry. Thus, a number of stakeholders would benefit from development of new, robust biomarkers for the prediction, diagnosis, and prognostication of adverse drug reactions. There has been significant recent progress in identifying predictive genomic biomarkers with the potential to be used in clinical settings to reduce the burden of adverse drug reactions. These have included biomarkers that can be used to alter drug dose (for example, Thiopurine methyltransferase (TPMT) and azathioprine dose) and drug choice. The latter have in particular included human leukocyte antigen (HLA) biomarkers which identify susceptibility to immune-mediated injuries to major organs such as skin, liver, and bone marrow from a variety of drugs. This review covers both the current state of the art with regard to genomic adverse drug reaction biomarkers. We also review circulating biomarkers that have the potential to be used for both diagnosis and prognosis, and have the added advantage of providing mechanistic information. In the future, we will not be relying on single biomarkers (genomic/non-genomic), but on multiple biomarker panels, integrated through the application of different omics technologies, which will provide information on predisposition, early diagnosis, prognosis, and mechanisms. Impact statement • Genetic and circulating biomarkers present significant opportunities to personalize patient therapy to minimize the risk of adverse drug reactions. ADRs are a significant heath issue

  13. Spallation reactions - physics and applications

    Kelic, A.; Ricciardi, M.; Schmidt, K-H.

    2009-01-01

    Spallation reactions have become an ideal tool for studying the equation of state and thermal instabilities of nuclear matter. In astrophysics, the interactions of cosmic rays with the interstellar medium have to be understood in detail for deducing their original composition and their production mechanisms. Renewed interest in spallation reactions with protons around 1 GeV came up recently with the developments of spallation neutron sources. The project of an accelerator-driven system (ADS) as a technological solution for incinerating the radioactive waste even intensified the efforts for better understanding the physics involved in the spallation process. Experiments on spallation reactions were performed for determining the production cross sections and properties of particles, fragments and heavy residues. Traditional experiments on heavy residues, performed in direct kinematics, were limited to the direct observation of long-lived radioactive nuclides and did not provide detailed information on the kinematics of the reaction. Therefore, an innovative experimental method has been developed, based on inverse kinematics, which allowed to identify all reaction residues in-flight, using the high resolution magnetic spectrometer FRS of GSL Darmstadt. It also gives direct access to the reaction kinematics. An experimental campaign has been carried out in a Europe-wide collaboration, investigating the spallation of several nuclei ranging from 56 Fe to 238 U Complementary experiments were performed with a full-acceptance detection system, yielding total fission cross sections. Recently, another detection system using the large acceptance ALADIN dipole and the LAND neutron detector was introduced to measure light particles in coincidence with the heavy residues. Another intense activity was dedicated to developing codes, which cover nuclear reactions occurring in an ADS. The first phase of the reaction is successfully described by a sequence of quasi-free nucleon

  14. Modeling of fluctuating reaction networks

    Lipshtat, A.; Biham, O.

    2004-01-01

    Full Text:Various dynamical systems are organized as reaction networks, where the population size of one component affects the populations of all its neighbors. Such networks can be found in interstellar surface chemistry, cell biology, thin film growth and other systems. I cases where the populations of reactive species are large, the network can be modeled by rate equations which provide all reaction rates within mean field approximation. However, in small systems that are partitioned into sub-micron size, these populations strongly fluctuate. Under these conditions rate equations fail and the master equation is needed for modeling these reactions. However, the number of equations in the master equation grows exponentially with the number of reactive species, severely limiting its feasibility for complex networks. Here we present a method which dramatically reduces the number of equations, thus enabling the incorporation of the master equation in complex reaction networks. The method is examplified in the context of reaction network on dust grains. Its applicability for genetic networks will be discussed. 1. Efficient simulations of gas-grain chemistry in interstellar clouds. Azi Lipshtat and Ofer Biham, Phys. Rev. Lett. 93 (2004), 170601. 2. Modeling of negative autoregulated genetic networks in single cells. Azi Lipshtat, Hagai B. Perets, Nathalie Q. Balaban and Ofer Biham, Gene: evolutionary genomics (2004), In press

  15. Combustion kinetics and reaction pathways

    Klemm, R.B.; Sutherland, J.W. [Brookhaven National Laboratory, Upton, NY (United States)

    1993-12-01

    This project is focused on the fundamental chemistry of combustion. The overall objectives are to determine rate constants for elementary reactions and to elucidate the pathways of multichannel reactions. A multitechnique approach that features three independent experiments provides unique capabilities in performing reliable kinetic measurements over an exceptionally wide range in temperature, 300 to 2500 K. Recent kinetic work has focused on experimental studies and theoretical calculations of the methane dissociation system (CH{sub 4} + Ar {yields} CH{sub 3} + H + Ar and H + CH{sub 4} {yields} CH{sub 3} + H{sub 2}). Additionally, a discharge flow-photoionization mass spectrometer (DF-PIMS) experiment is used to determine branching fractions for multichannel reactions and to measure ionization thresholds of free radicals. Thus, these photoionization experiments generate data that are relevant to both reaction pathways studies (reaction dynamics) and fundamental thermochemical research. Two distinct advantages of performing PIMS with high intensity, tunable vacuum ultraviolet light at the National Synchrotron Light Source are high detection sensitivity and exceptional selectivity in monitoring radical species.

  16. Dynamic effects in fragmentation reactions

    Bertsch, G. F.; Esbensen, H.

    2002-01-01

    Fragmentation reactions offer a useful tool to study the spectroscopy of halo nuclei, but the large extent of the halo wave function makes the reaction theory more difficult. The simple reaction models based on the eikonal approximation for the nuclear interaction or first-order perturbation theory for the Coulomb interaction have systematic errors that they investigate here, comparing to the predictions of complete dynamical calculations. They find that stripping probabilities are underpredicted by the eikonal model, leading to extracted spectroscopy strengths that are two large. In contrast, the Coulomb excitation is overpredicted by the simple theory. They attribute this to a screening effect, as is well known in the Barkas effect on stopping powers. The errors decrease with beam energy as E(sub beam)(sup -1), and are not significant at beam energies above 50 MeV/u. At lower beam energies, the effects should be taken into account when extracting quantitative spectroscopic strengths

  17. Fragmentation processes in nuclear reactions

    Legrain, R.

    1984-08-01

    Projectile and nuclear fragmentation are defined and processes referred to are recalled. The two different aspects of fragmentation are considered but the emphasis is also put on heavy ion induced reactions. The preliminary results of an experiment performed at GANIL to study peripheral heavy ions induced reactions at intermediate energy are presented. The results of this experiment will illustrate the characteristics of projectile fragmentation and this will also give the opportunity to study projectile fragmentation in the transition region. Then nuclear fragmentation is considered which is associated with more central collisions in the case of heavy ion induced reactions. This aspect of fragmentation is also ilustrated with two heavy ion experiments in which fragments emitted at large angle have been observed

  18. Effects of reaction channels in subbarrier fusion reactions

    Dasso, C.H.

    1984-01-01

    In this lecture we consider some aspects of fusion reactions between heavy ions at bombarding energies which are below or close to that of the Coulomb barrier. This problem has been traditionally confronted with simple barrier penetration calculations. So we start with a very brief review of what we can call the ''conventional'' procedure. (orig.)

  19. Effective dynamics along given reaction coordinates, and reaction rate theory.

    Zhang, Wei; Hartmann, Carsten; Schütte, Christof

    2016-12-22

    In molecular dynamics and related fields one considers dynamical descriptions of complex systems in full (atomic) detail. In order to reduce the overwhelming complexity of realistic systems (high dimension, large timescale spread, limited computational resources) the projection of the full dynamics onto some reaction coordinates is examined in order to extract statistical information like free energies or reaction rates. In this context, the effective dynamics that is induced by the full dynamics on the reaction coordinate space has attracted considerable attention in the literature. In this article, we contribute to this discussion: we first show that if we start with an ergodic diffusion process whose invariant measure is unique then these properties are inherited by the effective dynamics. Then, we give equations for the effective dynamics, discuss whether the dominant timescales and reaction rates inferred from the effective dynamics are accurate approximations of such quantities for the full dynamics, and compare our findings to results from approaches like Mori-Zwanzig, averaging, or homogenization. Finally, by discussing the algorithmic realization of the effective dynamics, we demonstrate that recent algorithmic techniques like the "equation-free" approach and the "heterogeneous multiscale method" can be seen as special cases of our approach.

  20. Estimation of the reaction efficiency in polymerase chain reaction

    Lalam, N.

    2006-01-01

    Polymerase chain reaction (PCR) is largely used in molecular biology for increasing the copy number of a specific DNA fragment. The succession of 20 replication cycles makes it possible to multiply the quantity of the fragment of interest by a factor of 1 million. The PCR technique has

  1. Reaction rate of propene pyrolysis.

    Han, Peipei; Su, Kehe; Liu, Yan; Wang, Yanli; Wang, Xin; Zeng, Qingfeng; Cheng, Laifei; Zhang, Litong

    2011-10-01

    The reaction rate of propene pyrolysis was investigated based on the elementary reactions proposed in Qu et al., J Comput Chem 2009, 31, 1421. The overall reaction rate was developed with the steady-state approximation and the rate constants of the elementary reactions were determined with the variational transition state theory. For the elementary reaction having transition state, the vibrational frequencies of the selected points along the minimum energy path were calculated with density functional theory at B3PW91/6-311G(d,p) level and the energies were improved with the accurate model chemistry method G3(MP2). For the elementary reaction without transition state, the frequencies were calculated with CASSCF/6-311G(d,p) and the energies were refined with the multireference configuration interaction method MRCISD/6-311G(d,p). The rate constants were evaluated within 200-2000 K and the fitted three-parameter expressions were obtained. The results are consistent with those in the literatures in most cases. For the overall rate, it was found that the logarithm of the rate and the reciprocal temperature have excellent linear relationship above 400 K, predicting that the rate follows a typical first-order law at high temperatures of 800-2000 K, which is also consistent with the experiments. The apparent activation energy in 800-2000 K is 317.3 kJ/mol from the potential energy surface of zero Kelvin. This value is comparable with the energy barriers, 365.4 and 403.7 kJ/mol, of the rate control steps. However, the apparent activation energy, 215.7 kJ/mol, developed with the Gibbs free energy surface at 1200 K is consistent with the most recent experimental result 201.9 ± 0.6 kJ/mol. Copyright © 2011 Wiley Periodicals, Inc.

  2. Clozapine-associated extrapyramidal reaction.

    Elliott, E S; Marken, P A; Ruehter, V L

    2000-05-01

    To report a case of extrapyramidal reaction associated with a dosage increase of clozapine. A 44-year-old white man with a 20-year history of chronic paranoid schizophrenia was admitted to an inpatient psychiatric facility. His prior medications restarted on admission were clozapine 650 mg at bedtime, haloperidol 10 mg at bedtime, clonazepam 2 mg/d, and aspirin 325 mg/d. Two days after admission (hospital day 3), clozapine and clonazepam were discontinued, and he was prescribed haloperidol 5 mg every morning and 10 mg every evening. Stabilization occurred over the following 24 days, with progressively lower dosages of haloperidol and increasing dosages of clozapine. Haloperidol was discontinued on day 24. On day 47, the patient was agitated and making bizarre statements; thus, the morning dose of clozapine was increased by 50 mg (total 450 mg/d). On day 48 at 2200, a dystonic reaction was diagnosed; he received intramuscular diphenhydramine 50 mg, which caused the reaction to subside. At the time of the adverse reaction, he was prescribed clozapine 450 mg/d, vitamin E 400 IU three times daily, aspirin 325 mg/d, and acetaminophen, milk of magnesia, and Maalox as needed. Although the risk of extrapyramidal symptoms (EPS) is significantly lower with clozapine than with conventional agents, elevated clozapine blood concentrations have been reported to cause EPS; other reports have cited severe dystonias and dyskinesias on abrupt clozapine withdrawal. Considering the medications prescribed at the time and the discontinuation of haloperidol 24 days before the event, clozapine was the most likely cause of the extrapyramidal reaction. Regardless of anticipated safety associated with novel antipsychotics such as clozapine, reports of dystonic reactions must be taken into account and patients monitored appropriately.

  3. Redox reactions in food fermentations

    Hansen, Egon Bech

    2018-01-01

    involves oxidative steps in the early part of the pathways whereas a multitude of different reactions are used as compensating reductions. Much of the diversity seen between food fermentations arise from the different routes and the different electron acceptors used by microorganisms to counterbalance...... and this contributes to the diversity in flavor, color, texture, and shelf life. The review concludes that these reactions are still only incompletely understood and that they represent an interesting area for fundamental research and also represent a fertile field for product development through a more conscious use...... of the redox properties of strains used to compose food cultures....

  4. Learning to Predict Chemical Reactions

    Kayala, Matthew A.; Azencott, Chloé-Agathe; Chen, Jonathan H.

    2011-01-01

    Being able to predict the course of arbitrary chemical reactions is essential to the theory and applications of organic chemistry. Approaches to the reaction prediction problems can be organized around three poles corresponding to: (1) physical laws; (2) rule-based expert systems; and (3) inductive machine learning. Previous approaches at these poles respectively are not high-throughput, are not generalizable or scalable, or lack sufficient data and structure to be implemented. We propose a new approach to reaction prediction utilizing elements from each pole. Using a physically inspired conceptualization, we describe single mechanistic reactions as interactions between coarse approximations of molecular orbitals (MOs) and use topological and physicochemical attributes as descriptors. Using an existing rule-based system (Reaction Explorer), we derive a restricted chemistry dataset consisting of 1630 full multi-step reactions with 2358 distinct starting materials and intermediates, associated with 2989 productive mechanistic steps and 6.14 million unproductive mechanistic steps. And from machine learning, we pose identifying productive mechanistic steps as a statistical ranking, information retrieval, problem: given a set of reactants and a description of conditions, learn a ranking model over potential filled-to-unfilled MO interactions such that the top ranked mechanistic steps yield the major products. The machine learning implementation follows a two-stage approach, in which we first train atom level reactivity filters to prune 94.00% of non-productive reactions with a 0.01% error rate. Then, we train an ensemble of ranking models on pairs of interacting MOs to learn a relative productivity function over mechanistic steps in a given system. Without the use of explicit transformation patterns, the ensemble perfectly ranks the productive mechanism at the top 89.05% of the time, rising to 99.86% of the time when the top four are considered. Furthermore, the system

  5. Vision 2020. Reaction Engineering Roadmap

    Klipstein, David H. [Reaction Design, San Diego, CA (United States); Robinson, Sharon [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2001-01-01

    The Reaction Engineering Roadmap is a part of an industry- wide effort to create a blueprint of the research and technology milestones that are necessary to achieve longterm industry goals. This report documents the results of a workshop focused on the research needs, technology barriers, and priorities of the chemical industry as they relate to reaction engineering viewed first by industrial use (basic chemicals; specialty chemicals; pharmaceuticals; and polymers) and then by technology segment (reactor system selection, design, and scale-up; chemical mechanism development and property estimation; dealing with catalysis; and new, nonstandard reactor types).

  6. Learning to predict chemical reactions.

    Kayala, Matthew A; Azencott, Chloé-Agathe; Chen, Jonathan H; Baldi, Pierre

    2011-09-26

    Being able to predict the course of arbitrary chemical reactions is essential to the theory and applications of organic chemistry. Approaches to the reaction prediction problems can be organized around three poles corresponding to: (1) physical laws; (2) rule-based expert systems; and (3) inductive machine learning. Previous approaches at these poles, respectively, are not high throughput, are not generalizable or scalable, and lack sufficient data and structure to be implemented. We propose a new approach to reaction prediction utilizing elements from each pole. Using a physically inspired conceptualization, we describe single mechanistic reactions as interactions between coarse approximations of molecular orbitals (MOs) and use topological and physicochemical attributes as descriptors. Using an existing rule-based system (Reaction Explorer), we derive a restricted chemistry data set consisting of 1630 full multistep reactions with 2358 distinct starting materials and intermediates, associated with 2989 productive mechanistic steps and 6.14 million unproductive mechanistic steps. And from machine learning, we pose identifying productive mechanistic steps as a statistical ranking, information retrieval problem: given a set of reactants and a description of conditions, learn a ranking model over potential filled-to-unfilled MO interactions such that the top-ranked mechanistic steps yield the major products. The machine learning implementation follows a two-stage approach, in which we first train atom level reactivity filters to prune 94.00% of nonproductive reactions with a 0.01% error rate. Then, we train an ensemble of ranking models on pairs of interacting MOs to learn a relative productivity function over mechanistic steps in a given system. Without the use of explicit transformation patterns, the ensemble perfectly ranks the productive mechanism at the top 89.05% of the time, rising to 99.86% of the time when the top four are considered. Furthermore, the system

  7. Dynamics of traveling reaction pulses

    Dovzhenko, A. Yu.; Rumanov, E. N.

    2007-01-01

    The growth of activator losses is accompanied by the decay of a traveling reaction pulse. In a ring reactor, this propagation threshold is present simultaneously with a threshold related to the ring diameter. The results of numerical experiments with pulses of an exothermal reaction reveal the transition from pulse propagation to a homogeneous hot regime, established regimes with periodic variations of the pulse velocity, and oscillatory decay of the pulse. When the medium becomes 'bistable' as a result of the variation in parameters, this factor does not prevent the propagation of pulses, but leads to changes in the pulse structure

  8. Theory of inclusive pionic reactions

    Oset, E.; Salcedo, L.L.; Strottman, D.

    1985-01-01

    A theory is developed for all the inclusive pion nuclear reactions, quasielastic, single charge exchange, double charge exchange and absorption, around the resonance region. The theory is based on the isobar hole model and makes an expansion in the number of particle-hole excitations. Up to 3p3h for pion absorption and 2p2h for quasielastic or charge exchange, where good convergence is found, are considered. The results obtained with this theory agree remarkably well with experiment for the different reactions and different nuclei in a wide region of energies around resonance

  9. Adverse reactions associated with acetylcysteine.

    Sandilands, E A; Bateman, D N

    2009-02-01

    Paracetamol (acetaminophen) is one of the most common agents deliberately ingested in self-poisoning episodes and a leading cause of acute liver failure in the western world. Acetylcysteine is widely acknowledged as the antidote of choice for paracetamol poisoning, but its use is not without risk. Adverse reactions, often leading to treatment delay, are frequently associated with both intravenous and oral acetylcysteine and are a common source of concern among treating physicians. A systematic literature review investigating the incidence, clinical features, and mechanisms of adverse effects associated with acetylcysteine. A variety of adverse reactions to acetylcysteine have been described ranging from nausea to death, most of the latter due to incorrect dosing. The pattern of reactions differs with oral and intravenous dosing, but reported frequency is at least as high with oral as intravenous. The reactions to the intravenous preparation result in similar clinical features to true anaphylaxis, including rash, pruritus, angioedema, bronchospasm, and rarely hypotension, but are caused by nonimmunological mechanisms. The precise nature of this reaction remains unclear. Histamine now seems to be an important mediator of the response, and there is evidence of variability in patient susceptibility, with females, and those with a history of asthma or atopy are particularly susceptible. Quantity of paracetamol ingestion, measured through serum paracetamol concentration, is also important as higher paracetamol concentrations protect patients against anaphylactoid effects. Most anaphylactoid reactions occur at the start of acetylcysteine treatment when concentrations are highest. Acetylcysteine also affects clotting factor activity, and this affects the interpretation of minor disturbances in the International Normalized Ratio in the context of paracetamol overdose. This review discusses the incidence, clinical features, underlying pathophysiological mechanisms, and

  10. Photonuclear reactions at intermediate energy

    Koch, J.H.

    1982-01-01

    The dominant feature of photonuclear reactions at intermediate energies is the excitation of the δ resonance and one can therefore use such reactions to study the dynamics of δ propagation in a nucleus. Following an introductory section the author comments on photoabsorption on a single nucleon in Section II. A review of the δ-n Greens function and of the photonuclear amplitude is given in Section III. Results for photoabsorption on 4 He are shown in Section IV and compared with the data. Coherent π 0 photoproduction is discussed in Section V and calculations for 12 C are compared to recent measurements. (Auth.)

  11. Hot wire radicals and reactions

    Zheng Wengang; Gallagher, Alan

    2006-01-01

    Threshold ionization mass spectroscopy is used to measure radical (and stable gas) densities at the substrate of a tungsten hot wire (HW) reactor. We report measurements of the silane reaction probability on the HW and the probability of Si and H release from the HW. We describe a model for the atomic H release, based on the H 2 dissociation model. We note major variations in silicon-release, with dependence on prior silane exposure. Measured radical densities versus silane pressure yield silicon-silane and H-silane reaction rate coefficients, and the dominant radical fluxes to the substrate

  12. Reaction

    raoul

    12 janv. 2012 ... Key words: Métastase, rate, colon, carcinome. Received: 28/12/2011 - Accepted: 09/01/2012 - Published: ... tomodensitométriques au moment du diagnostic du cancer primitif ou lors du suivi radiologique régulier des patients atteints de cancers. Le recours à la TEP-FDG couplée au scanner serait d'un ...

  13. Reactions

    Søndergaard, Morten

    2011-01-01

      My concern is to understand augmentation as an emergent modality - among many others in ‘the expanding digital field' (Søndergaard M. , Transformative Creativity in the Expanded Digital Field, 2009)' - attributed to the production of contemporary art and the ‘archive of knowledge' in the (art) ...

  14. Reaction-bonded silicon nitride

    Porz, F.

    1982-10-01

    Reaction-bonded silicon nitride (RBSN) has been characterized. The oxidation behaviour in air up to 1500 0 C and 3000 h and the effects of static and cyclic oxidation on room-temperature strength have been studied. (orig./IHOE) [de

  15. Microscopic description of nuclear reactions

    Gorbatov, A.M.

    1992-01-01

    The genealogical series method has been extended to the continuous spectrum of the many-body systems. New nonlinear integral equations have been formulated to perform the microscopical description of the nuclear reactions with arbitrary number of particles. The way to solve them numerically is demonstrated

  16. Reduction of chemical reaction models

    Frenklach, Michael

    1991-01-01

    An attempt is made to reconcile the different terminologies pertaining to reduction of chemical reaction models. The approaches considered include global modeling, response modeling, detailed reduction, chemical lumping, and statistical lumping. The advantages and drawbacks of each of these methods are pointed out.

  17. Palladium-Catalysed Coupling Reactions

    de Vries, Johannes G.; Beller, M; Blaser, HU

    2012-01-01

    Palladium-catalysed coupling reactions have gained importance as a tool for the production of pharmaceutical intermediates and to a lesser extent also for the production of agrochemicals, flavours and fragrances, and monomers for polymers. In this review only these cases are discussed where it seems

  18. Reactions to threatening health messages.

    Ten Hoor, Gill A; Peters, Gjalt-Jorn Y; Kalagi, Janice; de Groot, Lianne; Grootjans, Karlijne; Huschens, Alexander; Köhninger, Constanze; Kölgen, Lizan; Pelssers, Isabelle; Schütt, Toby; Thomas, Sophia; Ruiter, Robert A C; Kok, Gerjo

    2012-11-21

    Threatening health messages that focus on severity are popular, but frequently have no effect or even a counterproductive effect on behavior change. This paradox (i.e. wide application despite low effectiveness) may be partly explained by the intuitive appeal of threatening communication: it may be hard to predict the defensive reactions occurring in response to fear appeals. We examine this hypothesis by using two studies by Brown and colleagues, which provide evidence that threatening health messages in the form of distressing imagery in anti-smoking and anti-alcohol campaigns cause defensive reactions. We simulated both Brown et al. experiments, asking participants to estimate the reactions of the original study subjects to the threatening health information (n = 93). Afterwards, we presented the actual original study outcomes. One week later, we assessed whether this knowledge of the actual study outcomes helped participants to more successfully estimate the effectiveness of the threatening health information (n = 72). Results showed that participants were initially convinced of the effectiveness of threatening health messages and were unable to anticipate the defensive reactions that in fact occurred. Furthermore, these estimates did not improve after participants had been explained the dynamics of threatening communication as well as what the effects of the threatening communication had been in reality. These findings are consistent with the hypothesis that the effectiveness of threatening health messages is intuitively appealing. What is more, providing empirical evidence against the use of threatening health messages has very little effect on this intuitive appeal.

  19. HADES results in elementary reactions

    Ramstein B.

    2014-01-01

    Full Text Available Recent results obtained with the HADES experimental set-up at GSI are presented with a focus on dielectron production and strangeness in pp and quasi-free np reactions. Perspectives related to the very recent experiment using the pion beam at GSI are also discussed.

  20. Reactions of ethanol on Ru

    Sturm, Jacobus Marinus; Liu, Feng; Lee, Christopher James; Bijkerk, Frederik

    2012-01-01

    The adsorption and reactions of ethanol on Ru(0001) were studied with temperatureprogrammed desorption (TPD) and reflection-absorption infrared spectroscopy (RAIRS). Ethanol was found to adsorb intact onto Ru(0001) below 100 K. Heating to 250 K resulted in formation of ethoxy groups, which undergo

  1. Runaway Reaction: Solving for X.

    Bartz, Solveig A.

    2003-01-01

    This article examines the runaway reaction as it was displayed by Barry, a 14-year-old eighth-grade boy with learning disabilities. It identifies some of the common characteristics of this response and proposes school intervention methods. Functional behavioral assessments and strength-based assessments are encouraged, along with using strategy…

  2. Exchange effects in direct reactions

    LeMere, M.; Kanellopoulos, E.J.; Suenkel, W.; Tang, Y.C.

    1979-01-01

    The effect of antisymmetrization in direct reactions is examined by studying the properties of the coupling-normalization kernel function occurring in a resonating-group formulation. From this study, one obtains useful information concerning the general behavior of direct-reactiion processes and some justification for the use of three-body models in phenomenological analyses

  3. Scattering theory and chemical reactions

    Kuppermann, A.

    1988-01-01

    In this course, scattering theory and chemical reactions are presented including scattering of one particle by a potential, n-particle systems, colinear triatomic molecules and the study of reactive scattering for 3-dimensional triatomic systems. (A.C.A.S.) [pt

  4. Recyclization reactions leading to benzimidazoles

    Mamedov, Vakhid A; Murtazina, Anna M

    2011-01-01

    The published data on the recyclization reactions that afford benzimidazoles are generalized and systematized. Both classical and new methods of benzimidazole synthesis are considered. Attention is focused on the publications over the recent 10-15 years; of the earlier publications, only those unknown to the wide circle of chemists are analyzed.

  5. Recyclization reactions leading to benzimidazoles

    Mamedov, Vakhid A.; Murtazina, Anna M.

    2011-05-01

    The published data on the recyclization reactions that afford benzimidazoles are generalized and systematized. Both classical and new methods of benzimidazole synthesis are considered. Attention is focused on the publications over the recent 10-15 years; of the earlier publications, only those unknown to the wide circle of chemists are analyzed.

  6. Reactants encapsulation and Maillard Reaction

    Troise, A.D.; Fogliano, V.

    2013-01-01

    In the last decades many efforts have been addressed to the control of Maillard Reaction products in different foods with the aim to promote the formation of compounds having the desired color and flavor and to reduce the concentration of several potential toxic molecules. Encapsulation, already

  7. Ruthenium nanocatalysis on redox reactions.

    Veerakumar, Pitchaimani; Ramdass, Arumugam; Rajagopal, Seenivasan

    2013-07-01

    Nanoparticles have generated intense interest over the past 20 years due to their high potential applications in different areas such as catalysis, sensors, nanoscale electronics, fuel and solar cells and optoelectronics. As the large fractions of metal atoms are exposed to the surface, the use of metal nanoparticles as nanocatalysts allows mild reaction conditions and high catalytic efficiency in a large number of chemical transformations. They have emerged as sustainable heterogeneous catalysts and catalyst supports alternative to conventional materials. This review focuses on the synthesis, characterization and catalytic role of ruthenium nanoparticles (RuNPs) on the redox reactions of heteroatom containing organic compounds with the green reagent H2O2, a field that has attracted immense interest among the chemical, materials and industrial communities. We intend to present a broad overview of Ru nanocatalysts for redox reactions with an emphasis on their performance, stability and reusability. The growth in the chemistry of organic sulfoxides and N-oxides during last decade was due to their importance as synthetic intermediates for the production of a wide range of chemically and biologically active molecules. Thus design of efficient methods for the synthesis of sulfoxides and N-oxides becomes important. This review concentrates on the catalysis of RuNPs on the H2O2 oxidation of organic sulfides to sulfoxides and amines to N-oxides. The deoxygenation reactions of sulfoxides to sulfides and reduction of nitro compounds to amines are fundamental reactions in both chemistry and biology. Here, we also highlight the catalysis of metal nanoparticles on the deoxygenation of sulfoxides and sulfones and reduction of nitro compounds with particular emphasis on the mechanistic aspects.

  8. Reaction of hydrogen atoms with acrylaldehyde

    Koda, Seiichiro; Nakamura, Kazumoto; Hoshino, Takashi; Hikita, Tsutomu

    1978-01-01

    The reaction of hydrogen atoms with acrylaldehyde was investigated in a fast flow reactor equipped with a time-of-flight type mass spectrometer under reduced pressure. Main reaction products were carbon monoxide, ethylene, ethane, methane, and propanal. Consideration of the distributions of the reaction products under various reaction conditions showed that hydrogen atoms attacked the C=C double bond, especially its inner carbon side under reduced pressure. Resulting hot radicals caused subsequent reactions. The relative value of the apparent bimolecular rate constant of the reaction against that of trans-2-butene with hydrogen atoms was 1.6+-0.2, which supported the above-mentioned initial reaction. (auth.)

  9. Optimizing Chemical Reactions with Deep Reinforcement Learning.

    Zhou, Zhenpeng; Li, Xiaocheng; Zare, Richard N

    2017-12-27

    Deep reinforcement learning was employed to optimize chemical reactions. Our model iteratively records the results of a chemical reaction and chooses new experimental conditions to improve the reaction outcome. This model outperformed a state-of-the-art blackbox optimization algorithm by using 71% fewer steps on both simulations and real reactions. Furthermore, we introduced an efficient exploration strategy by drawing the reaction conditions from certain probability distributions, which resulted in an improvement on regret from 0.062 to 0.039 compared with a deterministic policy. Combining the efficient exploration policy with accelerated microdroplet reactions, optimal reaction conditions were determined in 30 min for the four reactions considered, and a better understanding of the factors that control microdroplet reactions was reached. Moreover, our model showed a better performance after training on reactions with similar or even dissimilar underlying mechanisms, which demonstrates its learning ability.

  10. Department of Nuclear Reaction - Overview

    Budzanowski, A.

    2000-01-01

    Full text: This year 1999 can be considered as very successful. Not only that we have published 33 papers in journals listed by the Philadelphia Institute of Science but because our hard work allowed us to obtain new and exciting results. A group of theoretical papers concerned with application of correlation among random matrices elements developed for statistical aspects of nuclear coupling into continuum to study of the collective effects in brain activity and stock market dynamics. These papers arose quite an interest and got several citations. Studies of the nonpartonic components in the nucleon structure function led to better understanding of the higher-twist effects. It was shown that inclusion of the terms of the order of 1/Q 4 improves fits to the experimental data. A review paper summarizing results on the role of the leading baryon in high energy reactions appeared in Progress on Nuclear and Particle Physics. Studies on multistep transfer reactions of light heavy ions in collaboration with the Institute of Nuclear Physics of the Ukrainian Academy of Sciences in Kiev have explained angular distributions of many reactions using the coupled channel theory. We have shown that it is possible to determine energy dependence of the optical model potential for such unstable nuclei like 8 Be. Further studies of mechanism of near threshold light meson production in collaboration with Juelich and Jagiellonian University were performed. Within COSY 10 and COSY 11 collaborations new data on the isospin symmetry breaking in pionic reactions and strange meson accompanied by hyperons emission were obtained. Together with colleagues from the Flerov Nuclear Reaction Laboratory we have started experiments with radioactive beams. Using magnetic separator COMBAS velocity distributions of isotopes with 2 ≤Z≤11 in reactions induced by 16 O on 9 Be were obtained. At the high resolution radioactive beam channel ACCULINA reactions induced by 6 He and 8 He nuclei were studied

  11. Multiresponse modelling of the caramelisation reaction

    Quintas, Mafalda; Guimarães, Carla; Baylina, João; Brandão, Teresa R. S.; Silva, Cristina L.M.

    2007-01-01

    Multiresponse modelling is a powerful tool for studying complex kinetics of reactions occurring in food products. This modelling technique uses information of reactants and products involved, allowing insightful kinetic parameters estimation and helping in clarifying reaction mechanisms. One example of a complex reaction that occurs in food processing is the caramelisation reaction. Caramelisation is the common name for a group of reactions observed when carbohydrates are exposed to high temp...

  12. Thermodynamics of Enzyme-Catalyzed Reactions Database

    SRD 74 Thermodynamics of Enzyme-Catalyzed Reactions Database (Web, free access)   The Thermodynamics of Enzyme-Catalyzed Reactions Database contains thermodynamic data on enzyme-catalyzed reactions that have been recently published in the Journal of Physical and Chemical Reference Data (JPCRD). For each reaction the following information is provided: the reference for the data, the reaction studied, the name of the enzyme used and its Enzyme Commission number, the method of measurement, the data and an evaluation thereof.

  13. Vanadocene reactions with hydroxy acids

    Latyaeva, V.N.; Lineva, A.N.; Zimina, S.V.; Ehllert, O.G.; Arsen'eva, T.I.

    1984-01-01

    To prepare a series of vanadium cyclopentadienylcarboxylates soluble in water, the vanadocene reactions with lactic, γ-oxybutyric-, salicylic,- gallic-, orotic-, and acetylsalicylic acids have been studied. To determine the influence of cyclopentadienyl groups, bound with a vanadium atom, on the physiological activity of the complexes formed, vanadium halides are made to react with lactic acid. Only the vanadocene reaction with orotic acid was conducted in an aqueous medium, other interactions were realized in the diethyl ether, toluene, T, H, P medium. The interaction of vanadocene and vanadium halides with lactic-, salicylic-, acetylsalicylic- and gallic acids was found to lead to the formation of water-soluble vanadium complexes of Cp 2 , VOCOR or CpV (OCOR) 2 type. The data on the produced compounds yield, their IR spectra, decomposition temperatures, solubility, effective magnetic moments are presented

  14. Allergic reactions in red tattoos

    Hutton Carlsen, K; Køcks, M; Sepehri, M

    2016-01-01

    to be feasible for chemical analysis of red pigments in allergic reactions. Raman spectroscopy has a major potential for fingerprint screening of problematic tattoo pigments in situ in skin, ex vivo in skin biopsies and in tattoo ink stock products, thus, to eliminate unsafe ink products from markets.......AIM: The aim of this study was to assess the feasibility of Raman spectroscopy as a screening technique for chemical characterisation of tattoo pigments in pathologic reacting tattoos and tattoo ink stock products to depict unsafe pigments and metabolites of pigments. MATERIALS/METHODS: Twelve...... dermatome shave biopsies from allergic reactions in red tattoos were analysed with Raman spectroscopy (A 785-nm 300 mW diode laser). These were referenced to samples of 10 different standard tattoo ink stock products, three of these identified as the culprit inks used by the tattooist and thus by history...

  15. Dehydrogenative Diels-Alder reaction.

    Ozawa, Takuya; Kurahashi, Takuya; Matsubara, Seijiro

    2011-10-07

    The dehydrogenative cycloaddition of dieneynes, which possess a diene in the form of a styrene moiety and a dienophile in the form of an alkyne moiety, produces naphthalene derivatives when heated. It was found that a key requirement of this process is the presence of a silyl group attached to the alkyne moiety, which forces a dehydrogenation reaction to occur. © 2011 American Chemical Society

  16. Caging in high energy reactions

    Ache, H.J.

    1977-01-01

    The concept of caging high energy reactions is considered. It is noted that there is no easy and unambiguous way, short of a complete and very tedious product and mechanistic analysis, which is feasible only for very few systems, to determine the contribution made by caging. It is emphasized that some products resulting from the hot reaction with a certain substrate may be formed via caging while others are not. In research on the mechanism of caging the results of Roots work on the reactions of hot 18 F with the CF 3 CH 3 system seem to provide evidence for caging, with 18 F being the caged moiety, thus proceeding via a radical--radical recombination mechanism. Their work with H 2 S additive also seems to indicate that scavenging via hydrogen abstraction from H 2 S to form does not interfere with the radical--radical recombination consistent with Bunkers molecular approach to explain the cage effects. In other research a series of observations resulting from stereochemical and combined stereochemical density variation techniques seem to favor a caged-complex. It is clear that a more conclusive answer can only be reached by more systematic studies, utilizing the whole range of nuclear reactions such as (n,2n), (n,γ) and E.C. processes in mechanistically well defined systems to elucidate the effect of variations in the recoil energies, by carrying out studies in different solvents or host substances to assess the effect of the physical parameters, such as molecule size and intermolecular interactions on the escape probability or caging efficiencies

  17. Reactions to threatening health messages

    ten Hoor Gill A

    2012-11-01

    Full Text Available Abstract Background Threatening health messages that focus on severity are popular, but frequently have no effect or even a counterproductive effect on behavior change. This paradox (i.e. wide application despite low effectiveness may be partly explained by the intuitive appeal of threatening communication: it may be hard to predict the defensive reactions occurring in response to fear appeals. We examine this hypothesis by using two studies by Brown and colleagues, which provide evidence that threatening health messages in the form of distressing imagery in anti-smoking and anti-alcohol campaigns cause defensive reactions. Methods We simulated both Brown et al. experiments, asking participants to estimate the reactions of the original study subjects to the threatening health information (n = 93. Afterwards, we presented the actual original study outcomes. One week later, we assessed whether this knowledge of the actual study outcomes helped participants to more successfully estimate the effectiveness of the threatening health information (n = 72. Results Results showed that participants were initially convinced of the effectiveness of threatening health messages and were unable to anticipate the defensive reactions that in fact occurred. Furthermore, these estimates did not improve after participants had been explained the dynamics of threatening communication as well as what the effects of the threatening communication had been in reality. Conclusions These findings are consistent with the hypothesis that the effectiveness of threatening health messages is intuitively appealing. What is more, providing empirical evidence against the use of threatening health messages has very little effect on this intuitive appeal.

  18. Reactions to threatening health messages

    ten Hoor, Gill A; Peters, Gjalt-Jorn Y; Kalagi, Janice; de Groot, Lianne; Grootjans, Karlijne; Huschens, Alexander; K?hninger, Constanze; K?lgen, Lizan; Pelssers, Isabelle; Sch?tt, Toby; Thomas, Sophia; Ruiter, Robert AC; Kok, Gerjo

    2012-01-01

    Abstract Background Threatening health messages that focus on severity are popular, but frequently have no effect or even a counterproductive effect on behavior change. This paradox (i.e. wide application despite low effectiveness) may be partly explained by the intuitive appeal of threatening communication: it may be hard to predict the defensive reactions occurring in response to fear appeals. We examine this hypothesis by using two studies by Brown and colleagues, which provide evidence th...

  19. Statistical theory of breakup reactions

    Bertulani, Carlos A.; Descouvemont, Pierre; Hussein, Mahir S.

    2014-01-01

    We propose an alternative for Coupled-Channels calculations with loosely bound exotic nuclei (CDCC), based on the the Random Matrix Model of the statistical theory of nuclear reactions. The coupled channels equations are divided into two sets. The first set, described by the CDCC, and the other set treated with RMT. The resulting theory is a Statistical CDCC (CDCC s ), able in principle to take into account many pseudo channels. (author)

  20. Nuclear reaction studies: Progress report

    Thaler, R.M.

    1986-01-01

    A principal focus of recent research has been the three-body problem. A great deal of effort has been devoted to the creation of a computer program to calculate physical observables in the three body problem below 1 GeV. Successful results have been obtained for the triton. Additional work concerns scattering of K + mesons from nuclei, antinucleon physics, relativistic nuclear physics and inclusive reactions

  1. Free radical reactions of daunorubicin

    Houee-Levin, C.

    1991-01-01

    Daunorubicin is an antitumor antibiotic activated in vivo by reduction. Its mechanism of action involves DNA and topoisomerase attack, but side effects are cytotoxicity related to free radical formation. Therefore the mechanism of the one-electron reduction of the drug and the reactions of the daunorubicin transients towards compounds of biological interest have been studied by the methods of radiolysis, in order to provide possible explanations of the drug mechanism of action. Their relative importance in cellular conditions is discussed [fr

  2. Statistical theory of breakup reactions

    Bertulani, Carlos A., E-mail: carlos.bertulani@tamuc.edu [Department of Physics and Astronomy, Texas A and M University-Commerce, Commerce, TX (United States); Descouvemont, Pierre, E-mail: pdesc@ulb.ac.be [Physique Nucleaire Theorique et Physique Mathematique, Universite Libre de Bruxelles (ULB), Brussels (Belgium); Hussein, Mahir S., E-mail: hussein@if.usp.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto de Estudos Avancados

    2014-07-01

    We propose an alternative for Coupled-Channels calculations with loosely bound exotic nuclei (CDCC), based on the the Random Matrix Model of the statistical theory of nuclear reactions. The coupled channels equations are divided into two sets. The first set, described by the CDCC, and the other set treated with RMT. The resulting theory is a Statistical CDCC (CDCC{sub s}), able in principle to take into account many pseudo channels. (author)

  3. Tuberculin reaction and BCG scar

    Timmermann, Clara Amalie Gade; Biering-Sørensen, Sofie; Aaby, Peter

    2015-01-01

    rate ratio (MRR) comparing children with a BCG scar with those without was 0.42 (95% CI = 0.19; 0.93). There was a similar tendency for TST positivity: MRR = 0.47 (95% CI = 0.14; 1.54). For LBW children who had both a positive TST reaction and a scar, the MRR was 0.22 (95% CI = 0.05; 0.87). For NBW...

  4. Sequential series for nuclear reactions

    Izumo, Ko

    1975-01-01

    A new time-dependent treatment of nuclear reactions is given, in which the wave function of compound nucleus is expanded by a sequential series of the reaction processes. The wave functions of the sequential series form another complete set of compound nucleus at the limit Δt→0. It is pointed out that the wave function is characterized by the quantities: the number of degrees of freedom of motion n, the period of the motion (Poincare cycle) tsub(n), the delay time t sub(nμ) and the relaxation time tausub(n) to the equilibrium of compound nucleus, instead of the usual quantum number lambda, the energy eigenvalue Esub(lambda) and the total width GAMMAsub(lambda) of resonance levels, respectively. The transition matrix elements and the yields of nuclear reactions also become the functions of time given by the Fourier transform of the usual ones. The Poincare cycles of compound nuclei are compared with the observed correlations among resonance levels, which are about 10 -17 --10 -16 sec for medium and heavy nuclei and about 10 -20 sec for the intermediate resonances. (auth.)

  5. Anaphylactic reactions presenting with hypertension.

    Solmazgul, Emrullah; Kutlu, Ali; Dogru, Salim; Ozalper, Veysel; Cetindagli, Ibrahim; Sezer, Ogun; Salmanoglu, Musa; Kilic, Erol; Karabacak, Ercan; Ozturk, Sami

    2016-01-01

    Although a few case reports about hypertensive anaphylaxis (HA) are available in the present literature, there is no study about the prevalence of HA. In this study, we review our cases with anaphylaxis presenting with hypertension and ascertain its prevalence. The documents of the patients who had anaphylactic reactions after the procedures performed for the diagnosis and treatment of allergic diseases in GATA Haydarpasa Clinic of Allergy and Immunology between January 2010 and December 2014 were retrospectively reviewed. Within the study period, 324 patients had undergone 4332 procedures in which 62 of them had developed anaphylaxis. During the procedures, the rate of anaphylaxis was found to be 1.43 %. The rate of HA among the anaphylaxis patients was 12.9 % (8 of 62 patients). During treatments, 2 patients received adrenaline injections without any adverse reaction. HA may be seen at a considerable rate during an anaphylactic reaction. Anaphylaxis and hypertension can be recovered by adrenaline injection when required. According to the best of our knowledge, this study is the first original study about the prevalence of HA in English-language medical literature.

  6. Department of Nuclear Reaction - Overview

    Budzanowski, A.

    2002-01-01

    Full text: Our research in 2001 can be characterized by a wide range of various subjects e.g. search for new physics in Au + Au collisions at the energy in the centre of mass per nucleon pair √ s NN = 200 GeV through hunting dibaryon formation in p + p → K + + D (dibaryon) reaction to the application of the random matrix theory taken from nuclear reaction studies in the analysis of fluctuations of the stock exchange time and space correlations. Heavy ion reactions have been studied in a broad range of energies. At low energy of the 12 C ions (E CM = 25.57 MeV), delivered by the Warsaw U200P cyclotron, the reactions induced on 11 B target were studied. Coupling effects between various reaction channels were found. At the energies corresponding to the liquid-to-gas phase transition, the onset of the flow phenomena was found in the multifragmentation of the 197 Au nuclei induced by a sequence of projectiles p, 4 He, 12 C of the energies from 1-3 GeV per nucleon. Finally, evidence of the melting of the baryonic structure of the colliding nuclei was found at the highest available energies of 200 GeV per nucleon pair, in the collision of gold nuclei studied at the Relativistic Heavy Ion Collider within the BRAHMS and PHOBOS collaboration. We entered a new collaboration HIRES with the aim to discover S = -1 dibaryonic state by studying the reaction p+p → K + +D. So far many attempts to prove experimentally the existence of a dibaryonic state failed. We hope to use the unique properties of the Big Karl spectrometer to prove the existence of a sharp peak in the energy spectra of kaons. To do so, we have to reduce strongly the background of pions. A diffusely reflective threshold Cherenkov detector made from silica aerogel was designed. Preliminary tests indicate that pionic signals can be reduced by a factor of 58. Extensive studies of the mechanism of generating collective levels and the energy gap by means of diagonalizing matrices with random elements ended up with

  7. Radiation reactions and care of the patient

    Lochhead, J.N.M.

    1983-01-01

    Many of the radiation reactions which may occur in patients following radiotherapy and the care of these reactions are described. These include the systemic reaction, reactions of the blood and skin, reactions occurring after treatment of the breast and chest wall, reactions after irradiation of the mouth and throat, intrathoracic tumours, the abdominal alimentary tract and pelvis, bone, the CNS and the eye. Patient care during the treatment of children and also during treatment using small sealed sources is also described. (U.K.)

  8. Metal-catalyzed asymmetric aldol reactions

    Dias, Luiz C.; Lucca Junior, Emilio C. de; Ferreira, Marco A. B.; Polo, Ellen C., E-mail: ldias@iqm.unicamp.br [Universidade de Campinas (UNICAMP), SP (Brazil). Inst. de Quimica

    2012-12-15

    The aldol reaction is one of the most powerful and versatile methods for the construction of C-C bonds. Traditionally, this reaction was developed in a stoichiometric version; however, great efforts in the development of chiral catalysts for aldol reactions were performed in recent years. Thus, in this review article, the development of metal-mediated chiral catalysts in Mukaiyama-type aldol reaction, reductive aldol reaction and direct aldol reaction are discussed. Moreover, the application of these catalysts in the total synthesis of complex molecules is discussed. (author)

  9. Chemical reactions in solvents and melts

    Charlot, G

    1969-01-01

    Chemical Reactions in Solvents and Melts discusses the use of organic and inorganic compounds as well as of melts as solvents. This book examines the applications in organic and inorganic chemistry as well as in electrochemistry. Organized into two parts encompassing 15 chapters, this book begins with an overview of the general properties and the different types of reactions, including acid-base reactions, complex formation reactions, and oxidation-reduction reactions. This text then describes the properties of inert and active solvents. Other chapters consider the proton transfer reactions in

  10. Substrate-Directed Catalytic Selective Chemical Reactions.

    Sawano, Takahiro; Yamamoto, Hisashi

    2018-05-04

    The development of highly efficient reactions at only the desired position is one of the most important subjects in organic chemistry. Most of the reactions in current organic chemistry are reagent- or catalyst-controlled reactions, and the regio- and stereoselectivity of the reactions are determined by the inherent nature of the reagent or catalyst. In sharp contrast, substrate-directed reaction determines the selectivity of the reactions by the functional group on the substrate and can strictly distinguish sterically and electronically similar multiple reaction sites in the substrate. In this Perspective, three topics of substrate-directed reaction are mainly reviewed: (1) directing group-assisted epoxidation of alkenes, (2) ring-opening reactions of epoxides by various nucleophiles, and (3) catalytic peptide synthesis. Our newly developed synthetic methods with new ligands including hydroxamic acid derived ligands realized not only highly efficient reactions but also pinpointed reactions at the expected position, demonstrating the substrate-directed reaction as a powerful method to achieve the desired regio- and stereoselective functionalization of molecules from different viewpoints of reagent- or catalyst-controlled reactions.

  11. Microfabricated sleeve devices for chemical reactions

    Northrup, M. Allen

    2003-01-01

    A silicon-based sleeve type chemical reaction chamber that combines heaters, such as doped polysilicon for heating, and bulk silicon for convection cooling. The reaction chamber combines a critical ratio of silicon and non-silicon based materials to provide the thermal properties desired. For example, the chamber may combine a critical ratio of silicon and silicon nitride to the volume of material to be heated (e.g., a liquid) in order to provide uniform heating, yet low power requirements. The reaction chamber will also allow the introduction of a secondary tube (e.g., plastic) into the reaction sleeve that contains the reaction mixture thereby alleviating any potential materials incompatibility issues. The reaction chamber may be utilized in any chemical reaction system for synthesis or processing of organic, inorganic, or biochemical reactions, such as the polymerase chain reaction (PCR) and/or other DNA reactions, such as the ligase chain reaction, which are examples of a synthetic, thermal-cycling-based reaction. The reaction chamber may also be used in synthesis instruments, particularly those for DNA amplification and synthesis.

  12. Department of Nuclear Reactions: Overview

    Rusek, K.

    2000-01-01

    Full text: During last year the physicists of the Department of Nuclear Reactions were involved in many experiments and projects: -Low energy nuclear reactions: For the first time a heavy ion beam from the Warsaw Cyclotron C-200 was used to investigate elastic and inelastic scattering of 12 C ions from 12 C target. The experiment is a part of a long range programme devoted to study the energy dependence of the nucleus-nucleus interactions. -Multifragmentation of relativistic heavy ions: Multifragmentation reactions induced by 12 C on different heavy targets and at different energies were studied in experiments performed at Gesellschaft fuer Schwerionenforschung by the ALADIN Collaboration. These asymmetric systems were investigated in order to study the interplay between preequilibrium and equilibrium phenomena in the nuclear liquid - gas phase transition. -The structure of nucleons: A novel, two-structure description of the Roper resonance was proposed on the basis of the α-p scattering data reanalysed by means of a T-matrix formalism. -Atomic physics: Emission of the X-rays by fast heavy ions (S, Ti, Fe) as they traverse the matter (thin carbon or other light element foil) was investigated in a series of experiments performed at University of Erlangen. It was demonstrated, that the characteristic K α X-rays emitted by a heavy ion can serve as a tool for Z-value control of the ion. -Material research: Semiconductor heterostructures were investigated by means of Rutherford Back Scattering and Channeling methods using the 2 MeV α particles from the Van de Graaff accelerator ''Lech'' at the Department. The following reports present the results and major successes which were achieved in 1999. (author)

  13. Neutral currents in semileptonic reactions

    Paschos, E.A.

    1975-05-01

    The evidence for weak neutral currents is analyzed in semileptonic reactions with special emphasis on their Lorentz and internal symmetry structure. It is found that present observations are consistent with the expectations of gauge theories, but other possibilities can not be ruled out. Of particular interest in this respect is the presence of a large isoscalar component. The excitation of the Δ-resonance by neutral currents is analyzed, and pion-nucleon mass distributions are presented. Charge asymmetries sensitive to isoscalar-isovector interferences are discussed. (U.S.)

  14. Kinetics of heterogeneous catalytic reactions

    Boudart, Michel

    2014-01-01

    This book is a critical account of the principles of the kinetics of heterogeneous catalytic reactions in the light of recent developments in surface science and catalysis science. Originally published in 1984. The Princeton Legacy Library uses the latest print-on-demand technology to again make available previously out-of-print books from the distinguished backlist of Princeton University Press. These paperback editions preserve the original texts of these important books while presenting them in durable paperback editions. The goal of the Princeton Legacy Library is to vastly increase acc

  15. Apparent tunneling in chemical reactions

    Henriksen, Niels Engholm; Hansen, Flemming Yssing; Billing, G. D.

    2000-01-01

    A necessary condition for tunneling in a chemical reaction is that the probability of crossing a barrier is non-zero, when the energy of the reactants is below the potential energy of the barrier. Due to the non-classical nature (i.e, momentum uncertainty) of vibrational states this is, however......, not a sufficient condition in order to establish genuine tunneling as a result of quantum dynamics. This proposition is illustrated for a two-dimensional model potential describing dissociative sticking of N-2 on Ru(s). It is suggested that the remarkable heavy atom tunneling, found in this system, is related...

  16. Reaction rates for neutrino processes

    Shalitin, D.

    1978-01-01

    Some integrals involved in neutrino processes are evaluated by transformation to a special system of reference - usually to the center of mass system (CM). Rather simple analytic expressions are obtained for reaction rates and, though less simple, for moments. An interesting result thus obtained is for an isotropic interaction (in CM) of a neutrino with a monoenergetic isotropic gas of extreme relativistic electrons: it is found that the probability of the scattered neutrino to have energy in a certain range is independent of this energy. (Auth.)

  17. Fragmentation processes in nuclear reactions

    Baur, G.; Roesel, F.; Trautmann, D.; Shyam, R.

    1983-10-01

    Fragmentation processes in nuclear collisions are reviewed. The main emphasis is put on light ion breakup at nonrelativistic energies. The post- and prior-form DWBA theories are discussed. The post-form DWBA, appropriate for the ''spectator breakup'' describes elastic as well as inelastic breakup modes. This theory can also account for the stripping to unbound states. The theoretical models are compared to typical experimental results to illustrate the various possible mechanisms. It is discussed, how breakup reactions can be used to study high-lying single particle strength in the continuum; how it can yield information about momentum distributions of fragments in the nucleus. (orig.)

  18. The first nuclear chain reaction

    Zinn, W.H.

    1989-01-01

    The author offers his recollections of the experimental efforts beginning in 1939 which culminated in the Chain Reaction in the squash court on December 2, 1942. Recalled are Columbia University experiments which did much to establish the feasibility of the chain in natural uranium and which stimulated the creation of the Manhattan District. The Columbia group moved to the University of Chicago, where, in early summer of 1942, construction and analysis of a number of subcritical reactors (piles) gave assurance with a high probability that only a reasonable amount of uranium and moderator would be required

  19. Giant resonances: reaction theory approach

    Toledo Piza, A.F.R. de; Foglia, G.A.

    1989-09-01

    The study of giant resonances through the use of reaction theory approach is presented and discussed. Measurements of cross-sections to the many available decay channels following excitation of giant multipole resonances (GMR) led one to view these phenomena as complicated dynamical syndromes so that theoretical requirements for their study must be extended beyond the traditional bounds of nuclear structure models. The spectra of decay products following GMR excitation in heavy nuclei are well described by statistical model (Hauser-Feshback, HF) predictions indicated that spreading of the collective modes plays a major role in shaping exclusive cross-sections. (A.C.A.S.) [pt

  20. Department of Nuclear Reactions: Overview

    Rusek, K.

    2002-01-01

    Full text: Department of Nuclear Reactions has had a very productive year. We have carried out our work in close collaborations with physicists from many laboratories, home and foreign. The following reports cover three major domains of our activities: nuclear, material and atomic physics. * Nuclear physics: In collaboration with scientists from Ukraine experimental studies of nuclear reaction induced by heavy ions from the Warsaw Cyclotron have been performed. The aim of the experiments is to study nuclear reactions leading to the exotic light nuclei in exit channels and energy dependence of the nucleus - nucleus interactions. Proton induced charge-exchange reactions were investigated theoretically by means of multistep-direct model. Good agreement with the experimental data was achieved. A novel approach to the problem of the nuclear liquid → gas phase transition was proposed, based on synergetics - a domain of science dealing with self-organization in macroscopic systems. Decay properties of the Roper resonance were studied. Final analysis of the analysing powers for the polarized deuterons scattered on protons was accomplished. Experimental programme of the near-threshold meson production in proton - proton scattering has been started in collaboration with Forschungszentrum. Juelich. * Atomic physics: Spectra of the X-rays emitted by energetic sulphur ions scattered off carbon atoms were analysed in order to study the role of the multiple charge states of the inner shells in the dynamics of the collision process. Ionization probabilities in collision of oxygen ions with gold atoms were measured. The observed disagreement of the experimental data with the theoretical predictions suggest a strong effect generated by the sub-shell couplings. * Materials research: Ion channelling method was applied to investigate transformation of the defects in Al x Ga 1-x As crystalline layers. Activities of our colleagues in didactics have grown considerably. Lectures

  1. Dibaryon resonances in photon induced reactions

    Schwille, W.J.

    1981-11-01

    The author gives a review about the production of dibaryon resonances in photon reactions on deuterium targets. Especially he considers the reactions γ + d → p + n, γ + d → p + X, and γ + d → p + N + π. (HSI)

  2. An efficient catalyst for asymmetric Reformatsky reaction

    rate enantioselectivity using N,N-dialkylnorephedrines as chiral ligands. ..... temperatures also, there was no product conversion. ... Optimization of reaction conditions for asymmetric Reformatsky reaction between benzaldehyde and α-.

  3. Scattering and transfer reactions with heavy ions

    Hussein, M.S.

    From the elastic scattering analysis the input parameters are found for the inelastic scattering analysis and the transfer reactions of the heavy ion reactions. The main theme reported is the likeness and conection among these processes. (L.C.) [pt

  4. High PT electronuclear reactions and spin observables

    Laget, J.M.

    1990-01-01

    The main arguments of the following topics are reviewed: the high transverse momentum exclusive reactions, the determination of various spin observables and the production of different flavours in reactions induced by real and virtual photons

  5. The mechanism of the modified Ullmann reaction

    Sperotto, Elena; Klink, Gerard P.M. van; Koten, Gerard van; Vries, Johannes G. de

    2010-01-01

    The copper-mediated aromatic nucleophilic substitution reactions developed by Fritz Ullmann and Irma Goldberg required stoichiometric amounts of copper and very high reaction temperatures. Recently, it was found that addition of relatively cheap ligands (diamines, aminoalcohols, diketones, diols)

  6. Catalyst Initiation in the Oscillatory Carbonylation Reaction

    Katarina Novakovic

    2011-01-01

    Full Text Available Palladium(II iodide is used as a catalyst in the phenylacetylene oxidative carbonylation reaction that has demonstrated oscillatory behaviour in both pH and heat of reaction. In an attempt to extract the reaction network responsible for the oscillatory nature of this reaction, the system was divided into smaller parts and they were studied. This paper focuses on understanding the reaction network responsible for the initial reactions of palladium(II iodide within this oscillatory reaction. The species researched include methanol, palladium(II iodide, potassium iodide, and carbon monoxide. Several chemical reactions were considered and applied in a modelling study. The study revealed the significant role played by traces of water contained in the standard HPLC grade methanol used.

  7. Amazing variational approach to chemical reactions

    Fernández, Francisco M.

    2009-01-01

    In this letter we analyse an amazing variational approach to chemical reactions. Our results clearly show that the variational expressions are unsuitable for the analysis of empirical data obtained from chemical reactions.

  8. Organic chemistry - Fast reactions 'on water'

    Klijn, JE; Engberts, JBFN

    2005-01-01

    Efficient reactions in aqueous organic chemistry do not require soluble reactants, as had been thought. A newly developed ‘on-water’ protocol is characterized by short reaction times, and the products are easy to isolate.

  9. Competing reaction channels in IR-laser-induced unimolecular reactions

    Berman, M.R.

    1981-01-01

    The competing reaction channels in the unimolecular decomposition of two molecules, formaldehyde and tetralin were studied. A TEA CO 2 laser was used as the excitation source in all experiments. The dissociation of D 2 CO was studied by infrared multiphoton dissociation (MPD) and the small-molecule nature of formaldehyde with regard to MPD was explored. The effect of collisions in MPD were probed by the pressure dependence of the MPD yield and ir fluorescence from multiphoton excited D 2 CO. MPD yield shows a near cubic dependence in pure D 2 CO which is reduced to a 1.7 power dependence when 15 torr of NO is added. The peak amplitude of 5 μm ir fluorescence from D 2 CO is proportional to the square of the D 2 CO pressure in pure D 2 CO or in the presence of 50 torr of Ar. Results are explained in terms of bottlenecks to excitation at the v = 1 level which are overcome by a combination of vibrational energy transfer and rotational relaxation. The radical/molecule branching ratio in D 2 CO MPD was 0.10 +- 0.02 at a fluence of 125 J/cm 2 at 946.0 cm -1 . The barrier height to molecular dissociation was calculated to be 3.6 +- 2.0 kcal/mole below the radical threshold or 85.0 +- 3.0 kcal/mole above the ground state of D 2 CO. In H 2 CO, this corresponds to 2.5 +- 2.0 kcal/mole below the radical threshold or 83.8 +- 3.0 kcal/mole above the ground state. Comparison with uv data indicate that RRKM theory is an acceptable description of formaldehyde dissociation in the 5 to 10 torr pressure range. The unimolecular decomposition of tetralin was studied by MPD and SiF 4 - sensitized pyrolysis. Both techniques induce decomposition without the interference of catalytic surfaces. Ethylene loss is identified as the lowest energy reaction channel. Dehydrogenation is found to result from step-wise H atom loss. Isomerization via disproportionation is also identified as a primary reaction channel

  10. Catalysis of Nuclear Reactions by Electrons

    Lipoglavšek, Matej

    2018-01-01

    Electron screening enhances nuclear reaction cross sections at low energies. We studied the nuclear reaction 1H(19F,αγ)16O in inverse kinematics in different solid hydrogen targets. Measured resonance strengths differed by up to a factor of 10 in different targets. We also studied the 2H(p,γ)3He fusion reaction and observed electrons emitted as reaction products instead of γ rays. In this case electron screening greatly enhances internal conversion probability.

  11. Multi-step direct reactions

    Koning, A.J.

    1992-07-01

    In recent years a variety of statistical theories has been developed concerning multistep direct (MSD) nuclear reactions. In addition, dominant in applications is a whole class of semiclassical models that may be subsumed under the heading of 'generalized exciton models'; these are basically MSD-type extensions on top of compound-like concepts. In this report the relation between their underlying statistical MSD-postulates are highlighted. A command framework is sketched that enables to generate the various MSD theories through assigning statistical properties to different parts of the nuclear Hamiltonian. Then it is shown that distinct forms of nuclear randomness are embodied in the mentioned theories. All these theories appear to be very similar at a qualitative level. In order to explain the high energy-tails and forward-peaked angular distribution typical for particles emitted in MSD reactions, it is imagined that the incident continuum particle stepwise looses its energy and direction in a sequence of collisions, thereby creating new particle-hole pairs in the target system. At each step emission may take place. The statistical aspect comes in because many continuum states are involved in the process. These are supposed to display chaotic behavior, the associated randomness assumption giving rise to important simplifications in the expression for MSD emission cross sections. This picture suggests that mentioned MSD models can be interpreted as a variant of essentially one and the same theory. 113 refs.; 25 figs.; 9 tabs

  12. Department of Nuclear Reactions: Overview

    Rusek, K.

    2001-01-01

    Full text: The last year of the twentieth-century was productive for our Department. Although the name of the Department suggests that we are all involved in investigations of nuclear reactions, in fact our activities are spread over three major domains: nuclear, atomic and material physics. Some of the projects we were involved in the last year have been realized using national facilities and accelerators, like the Van de Graaff accelerator of our Department at 69 Hoza Street, Warsaw Cyclotron U-200P of Warsaw University, and compact C30 cyclotron of our Institute at Swierk. Other projects were done abroad, using facilities of the Gesellschaft fuer Schwerionenforschung in Darmstadt, Institute de Physique Nucleaire at Orsay, and Universitaet Erlangen-Nuernberg in Erlangen. We carried out our work in close collaborations with physicists from many laboratories, Polish and foreign. - Low energy nuclear reactions. In collaboration with scientists from Ukraine experiments, using heavy ion beam provided by the Warsaw Cyclotron, were started. The aim of the experiments is to study nuclear reactions leading to the exotic light nuclei in exit channels and energy dependence of the nucleus - nucleus interaction. Efforts were made to develop a multistep direct model of nuclear reactions. In the model contributions due to the low energy collective excitations were taken into account. Good agreement with the experimental data was achieved. - Multifragmentation of relativistic heavy ions. ALADIN Collaboration studied multifragmentation reactions induced by relativistic heavy ions. The main activities of our scientists concentrated on an upgrade of the detecting system in order to replace photo multipliers with large area avalanche photodiodes in the central section of the TOF-wall. Some tests of the photodiodes manufactured by Advanced Photonix Inc. were performed using standard β - and γ-sources. - Structure of a nucleon. Decay properties of the Roper resonance were studied. A

  13. Reactions of butadiyne. 1: The reaction with hydrogen atoms

    Schwanebeck, W.; Warnatz, J.

    1984-01-01

    The reaction of hydrogen (H) atoms with butadiene (C4H2) was studied at room temperature in a pressure range between w mbar and 10 mbar. The primary step was an addition of H to C4H2 which is in its high pressure range at p 1 mbar. Under these conditions the following addition of a second H atom lies in the transition region between low and high pressure range. Vibrationally excited C4H4 can be deactivated to form buten-(1)-yne-(3)(C4H4) or decomposes into two C2H2 molecules. The rate constant at room temperature for primary step is given. The second order rate constant for the consumption of buten-(1)-yne-(3) is an H atom excess at room temperature is given.

  14. Parental Reactions to Cleft Palate Children.

    Vanpoelvoorde, Leah

    This literature review examines parental reactions following the birth of a cleft lip/palate child, focusing primarily on the mother's reactions. The research studies cited have explored such influences on maternal reactions as her feelings of lack of control over external forces and her feelings of guilt that the deformity was her fault. Delays…

  15. Hypersensitivity reactions in patients receiving hemodialysis.

    Butani, Lavjay; Calogiuri, Gianfranco

    2017-06-01

    To describe hypersensitivity reactions in patients receiving maintenance hemodialysis. PubMed search of articles published during the past 30 years with an emphasis on publications in the past decade. Case reports and review articles describing hypersensitivity reactions in the context of hemodialysis. Pharmacologic agents are the most common identifiable cause of hypersensitivity reactions in patients receiving hemodialysis. These include iron, erythropoietin, and heparin, which can cause anaphylactic or pseudoallergic reactions, and topical antibiotics and anesthetics, which lead to delayed-type hypersensitivity reactions. Many hypersensitivity reactions are triggered by complement activation and increased bradykinin resulting from contact system activation, especially in the context of angiotensin-converting enzyme inhibitor use. Several alternative pharmacologic preparations and dialyzer membranes are available, such that once an etiology for the reaction is established, recurrences can be prevented without affecting the quality of care provided to patients. Although hypersensitivity reactions are uncommon in patients receiving hemodialysis, they can be life-threatening. Moreover, considering the large prevalence of the end-stage renal disease population, the implications of such reactions are enormous. Most reactions are pseudoallergic and not mediated by immunoglobulin E. The multiplicity of potential exposures and the complexity of the environment to which patients on dialysis are exposed make it challenging to identify the precise cause of these reactions. Great diligence is needed to investigate hypersensitivity reactions to avoid recurrence in this high-risk population. Copyright © 2017 American College of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

  16. Use of Isotopes for Studying Reaction Mechanisms

    of atoms during a chemical transformation. This strategy of determining reaction mechanisms is illustrated in the article with several examples. Introduction. When a reaction is carried out, the primary effort goes towards the identification of the product(s) of the reaction. A more time consuming endeavour, however, is the ...

  17. Chemistry and reaction kinetics of biowaste torrefaction

    Stelt, van der M.J.C.

    2011-01-01

    This thesis addresses the question of how the chemistry and reaction kinetics of torrefaction are influenced by reaction conditions and the effects occuring during the reaction. This research question can be specified by questions such as, what controls their kinetics during torrefaction and what

  18. Infrared laser-induced chemical reactions

    Katayama, Mikio

    1978-01-01

    The experimental means which clearly distinguishes between infrared ray-induced reactions and thermal reactions has been furnished for the first time when an intense monochromatic light source has been obtained by the development of infrared laser. Consequently, infrared laser-induced chemical reactions have started to develop as one field of chemical reaction researches. Researches of laser-induced chemical reactions have become new means for the researches of chemical reactions since they were highlighted as a new promising technique for isotope separation. Specifically, since the success has been reported in 235 U separation using laser in 1974, comparison of this method with conventional separation techniques from the economic point of view has been conducted, and it was estimated by some people that the laser isotope separation is cheaper. This report briefly describes on the excitation of oscillation and reaction rate, and introduces the chemical reactions induced by CW laser and TEA CO 2 laser. Dependence of reaction yield on laser power, measurement of the absorbed quantity of infrared ray and excitation mechanism are explained. Next, isomerizing reactions are reported, and finally, isotope separation is explained. It was found that infrared laser-induced chemical reactions have the selectivity for isotopes. Since it is evident that there are many examples different from thermal and photo-chemical reactions, future collection of the data is expected. (Wakatsuki, Y.)

  19. Reaction Order Ambiguity in Integrated Rate Plots

    Lee, Joe

    2008-01-01

    Integrated rate plots are frequently used in reaction kinetics to determine orders of reactions. It is often emphasised, when using this methodology in practice, that it is necessary to monitor the reaction to a substantial fraction of completion for these plots to yield unambiguous orders. The present article gives a theoretical and statistical…

  20. Allergic reactions seen in orthodontic treatment

    Hande Görücü Coşkuner

    2016-01-01

    Full Text Available Allergy can be defined as inappropriate and harmful response to harmless and ordinary materials. Allergic reactions, like in other fields of dentistry, can also be seen in the field of orthodontics. The reactions that occur against orthodontic materials can be seen as irritant or hypersensitivity reactions. The main reason of the irritant reactions is friction between soft tissues and orthodontic appliances. However, the reason of the hypersensitivity reactions is usually the antigenicity of the materials. Hypersensitivity reactions are usually seen as allergic contact dermatitis on face and neck; the occurrence of mucosal-gingival reactions and dermal and systemic reactions are rare. Latex, metal and acrylic resins are the most common allergens in orthodontics. Apart from these materials, allergic reactions can occur against bonding materials, extraoral appliances, disinfectants and antimicrobial agents. The reactions that occur against extraoral appliances usually result from metallic and elastic parts of the appliances or the appliance parts that are in contact with skin. Orthodontists should be aware of the allergic reactions to protect their patients’ health. The aim of this review was to evaluate the allergic reactions seen in orthodontic patients and discuss the cautions that orthodontists can take.

  1. Modelling Students' Visualisation of Chemical Reaction

    Cheng, Maurice M. W.; Gilbert, John K.

    2017-01-01

    This paper proposes a model-based notion of "submicro representations of chemical reactions". Based on three structural models of matter (the simple particle model, the atomic model and the free electron model of metals), we suggest there are two major models of reaction in school chemistry curricula: (a) reactions that are simple…

  2. Chain chemical reactions during matrix devitrification

    Barkalov, I.M.

    1980-01-01

    Investigation results of chain reaction mechanisms, proceeding at devitrification of glass-like matrices under the effect of γ-irradiation are summarized. Peculiarities of kinetics and mechanism of chain reactions proceeding at devitrification are considered: hydrocarbon chlorination, polymerization of vinyl monomers, copolymerization and graft polymerization. Possible application aspects of the chain reaction conducting during matrix devitrification are also considered

  3. Polarization phenomena in heavy-ion reactions

    Sugimoto, K.; Ishihara, M.; Takahashi, N.

    1984-01-01

    This chapter presents a few key experiments which provide direct evidence of the polarization phenomena in heavy-ion reactions. The theory of polarization observables and measurements is given with the necessary formulae. The polarization phenomena is described and studies of product nuclear polarization in heavy-ion reactions are discussed. Studies of heavy-ion reactions induced by polarized beams are examined

  4. Reaction-Map of Organic Chemistry

    Murov, Steven

    2007-01-01

    The Reaction-Map of Organic Chemistry lists all the most commonly studied reactions in organic chemistry on one page. The discussed Reaction-Map will act as another learning aide for the students, making the study of organic chemistry much easier.

  5. Conceptual safety design analysis of Korea advanced liquid metal reactor

    Suk, S. D.; Park, C. K.

    1999-01-01

    The national long-term R and D program, updated in 1977, requires Korea Atomic Energy Research Institute (KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 Mwe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self-consistent design meeting a set of major safety design requirements for accident prevention. Some of the current emphasis includes those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve extensive supporting R and D programs. This paper summarizes some of the results of conceptual engineering and design analyses performed for the safety of KALIMER in the area of inherent safety, passive decay heat removal, sodium water reaction, and seismic isolation. (author)

  6. Department of Nuclear Reactions: Overview

    Rusek, K.

    2003-01-01

    Full text: In 2002, the Department has been involved in two new experimental programmes. Our colleagues led by Prof. Pawel Zupranski joined a large international collaboration HERMES and took part in experiments at DESY devoted to the study of the spin structure of the nucleon. Another group directed by Associate Prof. Bogdan Zwieglinski has worked on a conceptual design of a new generation detector PANDA (Proton-Antiproton Detection) which will be used in future experiments at GSI. Moreover, the experimental programmes covering three major domains of our scientific activities: nuclear physics, materials research and atomic physics were continued. - Nuclear physics: Experimental studies of nuclear reactions induced by heavy ions provided by the Warsaw U-200P Cyclotron were performed in collaboration with scientists from the Institute for Nuclear Studies in Kiev, Ukraine. The aim of the experiments was to investigate isotopic effects in the scattering of 11 B from carbon nuclides. Also, excited states of 6 Li predicted theoretically but never seen in experiments were investigated by means of one-neutron transfer reactions. Proton induced reactions were investigated theoretically by means of the multistep-direct model. Good agreement with the experimental data was achieved. The mechanism of fragments production in collisions of 197 Au with a gold target in the wide range of energies was studied by ALADIN and INDRA Collaborations. The production of η mesons from proton - proton collisions was investigated experimentally at the Juelich Cooler Synchrotron COSY. - Atomic physics: The ionisation of Au, Bi, Th and U atoms by Si ions was investigated in collaboration with the Swietokrzyska Academy, Kielce, and the University of Erlangen-Nuernberg. - Materials research: The sensitivity of the Solid State Nuclear Track PM-355 detectors was tested against intensive gamma and electron radiation. Moreover, using a monoenergetic sulphur ion beam from the Warsaw Cyclotron, the

  7. Incidents of chemical reactions in cell equipment

    Baldwin, N.M.; Barlow, C.R. [Uranium Enrichment Organization, Oak Ridge, TN (United States)

    1991-12-31

    Strongly exothermic reactions can occur between equipment structural components and process gases under certain accident conditions in the diffusion enrichment cascades. This paper describes the conditions required for initiation of these reactions, and describes the range of such reactions experienced over nearly 50 years of equipment operation in the US uranium enrichment program. Factors are cited which can promote or limit the destructive extent of these reactions, and process operations are described which are designed to control the reactions to minimize equipment damage, downtime, and the possibility of material releases.

  8. Kinetic studies of elementary chemical reactions

    Durant, J.L. Jr. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    This program concerning kinetic studies of elementary chemical reactions is presently focussed on understanding reactions of NH{sub x} species. To reach this goal, the author is pursuing experimental studies of reaction rate coefficients and product branching fractions as well as using electronic structure calculations to calculate transition state properties and reaction rate calculations to relate these properties to predicted kinetic behavior. The synergy existing between the experimental and theoretical studies allow one to gain a deeper insight into more complex elementary reactions.

  9. Plasma and controlled thermonuclear reaction

    Kapitsa, P.

    1980-01-01

    The principle and prospects are given of three methods of achieving controlled thermonuclear reaction. The original and so far most promising TOKAMAK method is presented invented in the USSR. Another method is the heating of a sphere about 1 mm in diameter from a mixture of deuterium and tritium by focused laser light from all sides. The third method consists in continuous plasma heating. A rope-like plasma discharge at a temperature of more than a million K results in the gas from microwave oscillations. The discharge is placed in a magnetic field and the ion temperature is increased by magneto-acoustic waves. A reactor is proposed operating on this principle and problems are pointed out which will have to be resolved. (M.S.)

  10. Plasma and controlled thermonuclear reaction

    Kapitsa, P

    1980-06-01

    The principle and prospects are given of three methods of achieving controlled thermonuclear reaction. The original and so far most promising TOKAMAK method is presented invented in the USSR. Another method is the heating of a sphere about 1 mm in diameter from a mixture of deuterium and tritium by focused laser light from all sides. The third method consists in continuous plasma heating. A rope-like plasma discharge at a temperature of more than a million K results in the gas from microwave oscillations. The discharge is placed in a magnetic field and the ion temperature is increased by magneto-acoustic waves. A reactor is proposed operating on this principle and problems are pointed out which will have to be resolved.

  11. Selected aspects of fusion reactions

    Lacroix, D.

    2003-01-01

    In this lecture, we present selected aspects of nuclear fusion. The importance of the initial geometry of the reaction and its relation to fusion barrier are first discussed. The effect of deformation leading to the notion of barrier distribution is then illustrated. After a brief overview of the advantages of macroscopic theories, the dynamics of nuclear system under large amplitude motion is reviewed. The di-nuclear concept is presented to understand the competition between fusion and quasi-fission. This concept is then generalized to account for the dissipative dynamics in multidimensional collective space. The last part of this lecture is devoted to new aspects encountered with radioactive beams specific properties of very extended neutron rich system, influence of pygmy or soft dipole resonances and charge exchange far from stability are discussed. (author)

  12. Department of Nuclear Reactions - Overview

    Budzanowski, A.

    1999-01-01

    Full text: The year 1998 can be considered as very successful both in harvesting important results from the existing collaborations as well as establishing new ones. In the frame of the COSY-11 collaboration cross section for η' production in p-p collision close to the threshold has been measured. In the region of excess energy between 1.5 and 4.1 MeV the η' cross sections are much lower than those of the π 0 and η production. There seems to be no indication that N * resonance doorway-like state governs the reaction mechanisms. The determined coupling constant g η'pp appears to be consistent with the prediction of the simple quark model. Results were published in Phys. Rev. Letters. Using the GEM detector, investigations of the isospin symmetry breaking were performed. Two reactions channels 3 Heπ 0 and 3 Hπ + from the reaction at proton momenta 700, 767, and 825 MeV/c were measured. Data analysis is in progress. The model of the meson cloud in the nucleon which is a speciality of our department has been successfully applied to explain the leading proton and neutron cross sections from the e + or e - proton collisions at the HERA ring. General formulas to calculate polarization of the particles with spin transmitted through the barrier in the presence of strong magnetic fields were obtained. New collaboration between our laboratory and the Institute for Nuclear Research in Kiev has been established. One PhD thesis was completed in the frame of this collaboration. We joined the new collaboration with Lund University concerning studies of hot nuclear matter properties using heavy ions from CELSIUS ring. First test of the phoswich detector for the forward wall was performed in Uppsala. Isoscalar giant dipole resonance strength distribution 3 ℎω has been evaluated in 208 Pb in the space of 1p1h and 2p2h excitation. The centroid energy of this state can directly be related to the nuclear incompressibility module. Our result indicates rather large values of

  13. Photonuclear spallation reactions in Cu

    Shibata, S.; Imamura, M.; Miyachi, T.

    1986-06-01

    Formation yields of 24 radioactive nuclides by the interaction of bremsstrahlung in the maximum end-point energies of 100 MeV - 1 GeV with Cu have been measured by direct γ-ray counting of irradiated targets. The yields in the mass range of 42 to 60 except for 60 Cu were analysed by non-linear least-squares fit to construct the mass yield and charge dispersion curves in spallation reactions. From the parameter values obtained, the energy dependence of the slope of the mass yield curve and the relationship between target N/Z and the most probable product N/Z were investigated in comparison with the results of proton, α and heavy ion-induced spallations of Cu. The characteristics of photon-induced spallations are discussed. (author)

  14. Department of Nuclear Reactions: Overview

    Rusek, K.

    2004-01-01

    Full text: In spite of reduced personnel the number of papers published and in press exceeded fifty, almost ten more than a year ago. Another good sign is the growing number of PhD students. The following short reports cover the three major domains of our scientific activities: nuclear, material and atomic physics. Nuclear physics: The structure of light nuclei was investigated, and studies of nuclear reactions induced by heavy ions were performed including experiments at the Heavy Ion Laboratory of Warsaw University. The experiments were carried out in collaboration with scientists from the Institute of Nuclear Research from Kiev, Ukraine. Proton induced reactions on zirconium were investigated theoretically by means of a multistep-direct model extended for the unbound particle - hole states. Good agreement with the experimental data was achieved. Isospin effects in multifragmentation of relativistic heavy ions were studied by the ALADIN Collaboration. Elements of a new generation detector PANDA were tested experimentally using a proton beam provided by the C-30 compact cyclotron at Swierk. Evidence of a narrow baryon state was found in a quasi - real photoproduction on the deuterium target by the HERMES Collaboration. Atomic physics: Ionisation of selected heavy elements by sulphur ions was investigated in collaboration with the Swietokrzyska Academy, Kielce. Materials research: Hydrogen release from ultrahigh molecular weight polythene was investigated by means of an α - particle beam from the Van de Graaff accelerator of our Department. Last but not least, many of our colleagues have been involved in education. Lectures on nuclear physics, accelerators, detectors used in nuclear research as well as nuclear methods applied in solid state studies for students from many high schools of Warsaw and for students of Warsaw University were given by Dr. Andrzej Korman and Dr. Lech Nowicki. Also, our Department made a significant contribution to the 7 th Science

  15. A Networks Approach to Modeling Enzymatic Reactions.

    Imhof, P

    2016-01-01

    Modeling enzymatic reactions is a demanding task due to the complexity of the system, the many degrees of freedom involved and the complex, chemical, and conformational transitions associated with the reaction. Consequently, enzymatic reactions are not determined by precisely one reaction pathway. Hence, it is beneficial to obtain a comprehensive picture of possible reaction paths and competing mechanisms. By combining individually generated intermediate states and chemical transition steps a network of such pathways can be constructed. Transition networks are a discretized representation of a potential energy landscape consisting of a multitude of reaction pathways connecting the end states of the reaction. The graph structure of the network allows an easy identification of the energetically most favorable pathways as well as a number of alternative routes. © 2016 Elsevier Inc. All rights reserved.

  16. Adverse reactions to radiopharmaceuticals and their reporting

    Keeling, D.

    1988-01-01

    Adverse reactions to radiopharmaceuticals are uncommon and the great majority that do occur are relatively trivial and require little or no treatment. Reporting schemes for such reactions are in operation in a number of countries but they vary in their effectiveness and the best collect only a minority of cases; only 10-15% of total reactions in the United Kingdom, for instance. Radiopharmaceutical reaction reports in the UK for the period 1982-1987 are summarised in a table and then discussed. Reliable incidence figures for such reactions are difficult to obtain. The UK figure is estimated here to be near 1 per 2000. The great majority of reactions reported are of an idiopathic hypersensitivity nature and are related to the chemical form of the material; radiation has very rarely caused recognisable problems since the discontinuance of colloid gold for lymphatic clearance studies. The value of such reaction reports is their role as a forewarning to doctors

  17. Interfacial reactions in intermetallic matrix composites

    Cantrell, L.B.; Clevenger, E.M.; Perepezko, J.H.

    1993-01-01

    The thermal stability of advanced composites is dominated by the behavior of internal interfaces. Analysis of these internal interfaces often involves consideration of at least ternary order phase equilibria. Limited thermodynamic data exists for ternary and higher order systems. However, a combined approach based upon the use of binary data to estimate ternary phase equilibria and experimentally determined reaction pathways is effective in the analysis of interface reactions in composite systems. In blended powder samples, thermal analysis was used to find possible reaction temperatures, while X-ray analysis, EDS, and EPMA of diffusion couples were used to assess interdiffusion reaction pathways. The approach is illustrated by compatibility studies between TiAl and TiSi 2 at 1,100 C, and in-situ reactions between B 4 C and TiAl at 1300 C where multiple reaction sequences have been analyzed to provide guidance for the design of in-situ reaction processing of composites

  18. Evolutionary change in continuous reaction norms

    Murren, Courtney J; Maclean, Heidi J; Diamond, Sarah E

    2014-01-01

    Understanding the evolution of reaction norms remains a major challenge in ecology and evolution. Investigating evolutionary divergence in reaction norm shapes between populations and closely related species is one approach to providing insights. Here we use a meta-analytic approach to compare...... divergence in reaction norms of closely related species or populations of animals and plants across types of traits and environments. We quantified mean-standardized differences in overall trait means (Offset) and reaction norm shape (including both Slope and Curvature). These analyses revealed...... contributed to the best-fitting models, especially for Offset, Curvature, and the total differences (Total) between reaction norms. Congeneric species had greater differences in reaction norms than populations, and novel environmental conditions increased the differences in reaction norms between populations...

  19. Nonequilibrium thermodynamics and a fluctuation theorem for individual reaction steps in a chemical reaction network

    Pal, Krishnendu; Das, Biswajit; Banerjee, Kinshuk; Gangopadhyay, Gautam

    2015-01-01

    We have introduced an approach to nonequilibrium thermodynamics of an open chemical reaction network in terms of the propensities of the individual elementary reactions and the corresponding reverse reactions. The method is a microscopic formulation of the dissipation function in terms of the relative entropy or Kullback-Leibler distance which is based on the analogy of phase space trajectory with the path of elementary reactions in a network of chemical process. We have introduced here a fluctuation theorem valid for each opposite pair of elementary reactions which is useful in determining the contribution of each sub-reaction on the nonequilibrium thermodynamics of overall reaction. The methodology is applied to an oligomeric enzyme kinetics at a chemiostatic condition that leads the reaction to a nonequilibrium steady state for which we have estimated how each step of the reaction is energy driven or entropy driven to contribute to the overall reaction. (paper)

  20. RxnFinder: biochemical reaction search engines using molecular structures, molecular fragments and reaction similarity.

    Hu, Qian-Nan; Deng, Zhe; Hu, Huanan; Cao, Dong-Sheng; Liang, Yi-Zeng

    2011-09-01

    Biochemical reactions play a key role to help sustain life and allow cells to grow. RxnFinder was developed to search biochemical reactions from KEGG reaction database using three search criteria: molecular structures, molecular fragments and reaction similarity. RxnFinder is helpful to get reference reactions for biosynthesis and xenobiotics metabolism. RxnFinder is freely available via: http://sdd.whu.edu.cn/rxnfinder. qnhu@whu.edu.cn.

  1. Explorations into Chemical Reactions and Biochemical Pathways.

    Gasteiger, Johann

    2016-12-01

    A brief overview of the work in the research group of the present author on extracting knowledge from chemical reaction data is presented. Methods have been developed to calculate physicochemical effects at the reaction site. It is shown that these physicochemical effects can quite favourably be used to derive equations for the calculation of data on gas phase reactions and on reactions in solution such as aqueous acidity of alcohols or carboxylic acids or the hydrolysis of amides. Furthermore, it is shown that these physicochemical effects are quite effective for assigning reactions into reaction classes that correspond to chemical knowledge. Biochemical reactions constitute a particularly interesting and challenging task for increasing our understanding of living species. The BioPath.Database is a rich source of information on biochemical reactions and has been used for a variety of applications of chemical, biological, or medicinal interests. Thus, it was shown that biochemical reactions can be assigned by the physicochemical effects into classes that correspond to the classification of enzymes by the EC numbers. Furthermore, 3D models of reaction intermediates can be used for searching for novel enzyme inhibitors. It was shown in a combined application of chemoinformatics and bioinformatics that essential pathways of diseases can be uncovered. Furthermore, a study showed that bacterial flavor-forming pathways can be discovered. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Department of Nuclear Reactions: Overview

    Rusek, K.

    1999-01-01

    Full text: The Department of Nuclear Reactions had a very productive year. The following reports cover three major domains of our activities: nuclear, material and atomic physics. One of the current questions in modern nuclear physics is question of the phase transitions in nuclear matter. Our physicists, the members of the ALADIN Collaboration at Gesellschaft fuer Schwerionenforschung, participated in new experiments exploring properties of highly excited nuclear matter and the phenomenon of the liquid - gas phase transition. The experiments yielded a number of important results. Details can be found in the three short reports presented in this volume. Structure of a nucleon is another important subject of nuclear science research. In the last year energy region of Δ resonance has been investigated by means of charge exchange reaction. The experiment was performed at Laboratory National Saturne in Saclay by SPESIV-π collaboration consisting of physicist from Institute of Nuclear Physics Orsay, Niels Bohr Institute Copenhagen and from our Department. The main achievement of the experiment was evidence for a Δ - hole attraction in the spin longitudinal channel. Reactions induced by radioactive ion beams such as 6 He recently attract a lot of interest. There exist some evidences that the 6 He nucleus has a two-neutron halo structure similar to that well established for 11 Li. An analysis of 6 He + 4 He scattering data reported in this volume revealed some similarities between the loosely bound 6 Li nucleus and the neutron rich 6 He. Research in material physics has focused on two basic topics: a crystallographic model of uranium dioxide, a material currently used as a nuclear fuel and transformations of defects in GaAs crystals at low temperature. The investigations have been carried out in a wide collaboration with scientists from the University of Jena, Research Center Karlsruhe and Centre de Spectrometrie Nucleaire Orsay. Some experiments have been performed at

  3. Department of Nuclear Reactions: Overview

    Rusek, K.

    1998-01-01

    (full text) During the last year our activities were spread over the three major domains: nuclear, atomic and material physics. The nuclear physics experimental programme covered a broad range of nuclear reactions induced by light and heavy ions. New experiments were performed at the compact C-30 cyclotron at Swierk, at University of Jyvaeskylae, GSI Darmstadt, LN Saturne. Prospects for future experiments on nucleon structure at Forschungszentrum Juelich were open. The collaboration with INR Kiev was tightened and work was done in order to prepare experiments at the C-200 heavy ion cyclotron in Warsaw. An effort to install the ion guide isotope separator on line (IGISOL) at the C-200 cyclotron has also to be mentioned A half a year stay of Dr. Nicholas Keeley in the Department, who received The Royal Society/Polish Academy of Science grant, resulted in many interesting results on breakup of light nuclei. Details can be found in the short abstracts presented in this report. As far as atomic physics is concerned, the activity of a group lead by Prof. Marian Jaskola yielded various new results. The experiments were performed at the University of Erlangen, in close collaboration with the Pedagogical University in Kielce and the University of Basel. Fast neutrons generated in the 3 H(d,n) 4 He reaction induced by the 2 MeV deuteron beam from the Van der Graaff accelerator at the Department were used to calibrate solid state-nuclear-track detectors. This was a very good year for material physics research: Jan Kaczanowski and Slawomir Kwiatkawski received Ph.D. degrees based on dissertation research performed in the material physics research programme, while Pawel Kolodziej completed his MSc. thesis in collaboration with the Institute of Electronic Materials Technology in Warsaw, Research Center Karlsruhe, University of Jena and CSNSM Orsay many results were obtained. Lech Nowicki and Prof. Andrzej Turos were awarded by the Director of the IPJ prizes for their scientific

  4. ReactionPredictor: prediction of complex chemical reactions at the mechanistic level using machine learning.

    Kayala, Matthew A; Baldi, Pierre

    2012-10-22

    Proposing reasonable mechanisms and predicting the course of chemical reactions is important to the practice of organic chemistry. Approaches to reaction prediction have historically used obfuscating representations and manually encoded patterns or rules. Here we present ReactionPredictor, a machine learning approach to reaction prediction that models elementary, mechanistic reactions as interactions between approximate molecular orbitals (MOs). A training data set of productive reactions known to occur at reasonable rates and yields and verified by inclusion in the literature or textbooks is derived from an existing rule-based system and expanded upon with manual curation from graduate level textbooks. Using this training data set of complex polar, hypervalent, radical, and pericyclic reactions, a two-stage machine learning prediction framework is trained and validated. In the first stage, filtering models trained at the level of individual MOs are used to reduce the space of possible reactions to consider. In the second stage, ranking models over the filtered space of possible reactions are used to order the reactions such that the productive reactions are the top ranked. The resulting model, ReactionPredictor, perfectly ranks polar reactions 78.1% of the time and recovers all productive reactions 95.7% of the time when allowing for small numbers of errors. Pericyclic and radical reactions are perfectly ranked 85.8% and 77.0% of the time, respectively, rising to >93% recovery for both reaction types with a small number of allowed errors. Decisions about which of the polar, pericyclic, or radical reaction type ranking models to use can be made with >99% accuracy. Finally, for multistep reaction pathways, we implement the first mechanistic pathway predictor using constrained tree-search to discover a set of reasonable mechanistic steps from given reactants to given products. Webserver implementations of both the single step and pathway versions of Reaction

  5. Fermentation reactions of Erysipelothrix rhusiopathiae.

    WHITE, T G; SHUMAN, R D

    1961-10-01

    White, Thomas G. (U. S. Department of Agriculture, Ames, Iowa), and Richard D. Shuman. Fermentation reactions of Erysipelothrix rhusiopathiae. J. Bacteriol. 82:595-599. 1961.-A study was made to determine the effect of four different basal media, to which fermentable carbon compounds had been added, upon 22 selected strains of Erysipelothrix rhusiopathiae (insidiosa). Acid production was measured by (i) chemical indicator, (ii) change in pH, and (iii) production of titrable acidity. At least two determinations, usually four, were made for each test on each strain. The fermentation pattern varied according to the medium, the indicator, and the method of measuring acid production. Andrade's base plus serum was the most dependable medium because it permitted the least variation in the total number of different patterns. Of the three methods used to measure acid production, the chemical indicator gave the most valid and reproducible results. The within-strain variation was not extreme and most strains persisted in a given fermentation pattern under like conditions of growth and acid production. Results of the study indicated that, regardless of the medium and indicator routinely used, one should be familiar with the fermentation pattern of known strains of the erysipelas organism.

  6. Interfacial reactions in lithium batteries

    Chen, Zonghai; Amine, Khalil; Amine, Rachid; Ma, Zi-Feng

    2017-01-01

    The lithium-ion battery was first commercially introduced by Sony Corporation in 1991 using LiCoO 2 as the cathode material and mesocarbon microbeads (MCMBs) as the anode material. After continuous research and development for 25 years, lithium-ion batteries have been the dominant energy storage device for modern portable electronics, as well as for emerging applications for electric vehicles and smart grids. It is clear that the success of lithium-ion technologies is rooted to the existence of a solid electrolyte interphase (SEI) that kinetically suppresses parasitic reactions between the lithiated graphitic anodes and the carbonate-based non-aqueous electrolytes. Recently, major attention has been paid to the importance of a similar passivation/protection layer on the surface of cathode materials, aiming for a rational design of high-energy-density lithium-ion batteries with extended cycle/calendar life. In this article, the physical model of the SEI, as well as recent research efforts to understand the nature and role of the SEI are summarized, and future perspectives on this important research field will also be presented. (topical review)

  7. Interfacial reactions in lithium batteries

    Chen, Zonghai; Amine, Rachid; Ma, Zi-Feng; Amine, Khalil

    2017-08-01

    The lithium-ion battery was first commercially introduced by Sony Corporation in 1991 using LiCoO2 as the cathode material and mesocarbon microbeads (MCMBs) as the anode material. After continuous research and development for 25 years, lithium-ion batteries have been the dominant energy storage device for modern portable electronics, as well as for emerging applications for electric vehicles and smart grids. It is clear that the success of lithium-ion technologies is rooted to the existence of a solid electrolyte interphase (SEI) that kinetically suppresses parasitic reactions between the lithiated graphitic anodes and the carbonate-based non-aqueous electrolytes. Recently, major attention has been paid to the importance of a similar passivation/protection layer on the surface of cathode materials, aiming for a rational design of high-energy-density lithium-ion batteries with extended cycle/calendar life. In this article, the physical model of the SEI, as well as recent research efforts to understand the nature and role of the SEI are summarized, and future perspectives on this important research field will also be presented.

  8. Shape nuclei and nuclear reactions

    Yushkov, A.V.

    1975-01-01

    Experimental methods for obtaining the nucleus shape parameters are reviewed throughout the period of 1955-1975. Spatial properties of a nucleus, which can be directly or indirectly measured, are determined. They include: parameters of nucleus localization in space; parameters characterizing the nucleus nonsphericity; parameters of the nucleus nonaxiality. Dimensional parameters of a nucleus, namely, radius R and surface ΔR are derived from electron scattering. The deformation sign is indirectly obtained in the experiments. Parameters of the nucleus shape, namely, the sign and magnitude of nuclear deformation are derived from the mean energy proton scattering by a coupled channels method. The only direct way of deriving the nucleus surface deformation signs is the method of the Blaire phase shift. Results on scattering of electrons, protons, and α-particles on light and medium nuclei are reported. Data on the nucleus shape can be also obtained from reactions with heavy ions. A difference between strong absorptions of incident particles of high and average energy by a nucleus is noted. Numerous diagrams illustrate experimental and theoretical results

  9. Breast Cancer: Reactions, Choices, Decisions

    Waring, Alexia N.

    2000-01-01

    Women with breast cancer often experience a predictable set of emotional and psychological reactions to their cancer diagnosis according to recognized influencing factors such as age at the time of diagnosis and stage of life. The time between a breast biopsy and the receipt of the pathology results has been identified by patients as the most stressful period throughout the entire cancer experience. Treatment decisions, until recently, were made solely by physicians while patients assumed passive roles. Increasingly, breast cancer patients want to assume an active role in their treatment decisions and care and are no longer satisfied to be passive observers. More and more women educate themselves about their disease through the Internet, investigating available treatment options, side effects, and in some cases, alternative therapies. This new type of breast cancer patient wants to be cared for by physicians who embrace the patient as part of the team. They appreciate the physician who is not threatened by the educated breast cancer patient and understands that she is ultimately motivated by an attempt to regain some of the control the cancer has taken away from her. PMID:21765661

  10. Glycation Reactions of Casein Micelles.

    Moeckel, Ulrike; Duerasch, Anja; Weiz, Alexander; Ruck, Michael; Henle, Thomas

    2016-04-13

    After suspensions of micellar casein or nonmicellar sodium caseinate had been heated, respectively, in the presence and absence of glucose for 0-4 h at 100 °C, glycation compounds were quantitated. The formation of Amadori products as indicators for the "early" Maillard reaction were in the same range for both micellar and nonmicellar caseins, indicating that reactive amino acid side chains within the micelles are accessible for glucose in a comparable way as in nonmicellar casein. Significant differences, however, were observed concerning the formation of the advanced glycation end products (AGEs), namely, N(ε)-carboxymethyllysine (CML), pyrraline, pentosidine, and glyoxal-lysine dimer (GOLD). CML could be observerd in higher amounts in nonmicellar casein, whereas in the micelles the pyrraline formation was increased. Pentosidine and GOLD were formed in comparable amounts. Furthermore, the extent of protein cross-linking was significantly higher in the glycated casein micelles than in the nonmicellar casein samples. Dynamic light scattering and scanning electron microscopy showed that glycation has no influence on the size of the casein micelles, indicating that cross-linking occurs only in the interior of the micelles, but altered the surface morphology. Studies on glycation and nonenzymatic cross-linking can contribute to the understanding of the structure of casein micelles.

  11. Cluster model in reaction theory

    Adhikari, S.K.

    1979-01-01

    A recent work by Rosenberg on cluster states in reaction theory is reexamined and generalized to include energies above the threshold for breakup into four composite fragments. The problem of elastic scattering between two interacting composite fragments is reduced to an equivalent two-particle problem with an effective potential to be determined by extremum principles. For energies above the threshold for breakup into three or four composite fragments effective few-particle potentials are introduced and the problem is reduced to effective three- and four-particle problems. The equivalent three-particle equation contains effective two- and three-particle potentials. The effective potential in the equivalent four-particle equation has two-, three-, and four-body connected parts and a piece which has two independent two-body connected parts. In the equivalent three-particle problem we show how to include the effect of a weak three-body potential perturbatively. In the equivalent four-body problem an approximate simple calculational scheme is given when one neglects the four-particle potential the effect of which is presumably very small

  12. Alchemical derivatives of reaction energetics

    Sheppard, Daniel; Henkelman, Graeme; von Lilienfeld, O. Anatole

    2010-08-01

    Based on molecular grand canonical ensemble density functional theory, we present a theoretical description of how reaction barriers and enthalpies change as atoms in the system are subjected to alchemical transformations, from one element into another. The change in the energy barrier for the umbrella inversion of ammonia is calculated along an alchemical path in which the molecule is transformed into water, and the change in the enthalpy of protonation for methane is calculated as the molecule is transformed into a neon atom via ammonia, water, and hydrogen fluoride. Alchemical derivatives are calculated analytically from the electrostatic potential in the unperturbed system, and compared to numerical derivatives calculated with finite difference interpolation of the pseudopotentials for the atoms being transformed. Good agreement is found between the analytical and numerical derivatives. Alchemical derivatives are also shown to be predictive for integer changes in atomic numbers for oxygen binding to a 79 atom palladium nanoparticle, illustrating their potential use in gradient-based optimization algorithms for the rational design of catalysts.

  13. Quantum indistinguishability in chemical reactions.

    Fisher, Matthew P A; Radzihovsky, Leo

    2018-05-15

    Quantum indistinguishability plays a crucial role in many low-energy physical phenomena, from quantum fluids to molecular spectroscopy. It is, however, typically ignored in most high-temperature processes, particularly for ionic coordinates, implicitly assumed to be distinguishable, incoherent, and thus well approximated classically. We explore enzymatic chemical reactions involving small symmetric molecules and argue that in many situations a full quantum treatment of collective nuclear degrees of freedom is essential. Supported by several physical arguments, we conjecture a "quantum dynamical selection" (QDS) rule for small symmetric molecules that precludes chemical processes that involve direct transitions from orbitally nonsymmetric molecular states. As we propose and discuss, the implications of the QDS rule include ( i ) a differential chemical reactivity of para- and orthohydrogen, ( ii ) a mechanism for inducing intermolecular quantum entanglement of nuclear spins, ( iii ) a mass-independent isotope fractionation mechanism, ( iv ) an explanation of the enhanced chemical activity of "reactive oxygen species", ( v ) illuminating the importance of ortho-water molecules in modulating the quantum dynamics of liquid water, and ( vi ) providing the critical quantum-to-biochemical linkage in the nuclear spin model of the (putative) quantum brain, among others.

  14. Transfer and breakup reactions at intermediate energies

    Stokstad, R.G.

    1986-04-01

    The origin of the quasi-elastic peak in peripheral heavy-ion reactions is discussed in terms of inelastic scattering and transfer reactions to unbound states of the primary projectile-like fragment. The situation is analogous to the use of reverse kinematics in fusion reactions, a technique in which the object of study is moving with nearly the beam velocity. It appears that several important features of the quasi-elastic peak may be explained by this approach. Projectile-breakup reactions have attractive features for the study of nuclear structure. They may also be used to determine the partition of excitation energy in peripheral reactions. At intermediate energies, neutron-pickup reactions leading to four-body final states become important. Examples of experiments are presented that illustrate these points. 15 refs., 14 figs

  15. Delayed reactions to reusable protective gloves.

    Pontén, Ann; Dubnika, Inese

    2009-04-01

    The materials in plastic protective gloves are thought to cause less contact allergy than rubber gloves. Our aim was to estimate the frequency of delayed reactions to different types of reusable protective gloves among dermatitis patients. 2 x 2 cm pieces of polyvinyl chloride (PVC) gloves, nitrile gloves, and natural rubber latex (NRL) gloves were tested as is in consecutive dermatitis patients tested with the baseline series. Among 658 patients, 6 patients reacted to PVC gloves and 6 patients to the NRL gloves. None reacted to both these types of gloves. Five of six patients with reactions to rubber gloves reacted to thiuram mix in the baseline series. Delayed reactions to reusable PVC gloves may be as common as to reusable NRL gloves. In contrast to most reactions to the NRL glove, the reactions to the PVC glove had no obvious association with reactions to any allergen(s) in the baseline series.

  16. Measurement of inertial confinement fusion reaction rate

    Peng Xiaoshi; Wang Feng; Tang Daorun; Liu Shenye; Huang Tianxuan; Liu Yonggang; Xu Tao; Chen Ming; Mei Yu

    2011-01-01

    Fusion reaction rate is an important parameter for measuring compression during the implosion in inertial confinement fusion experiment. We have developed a system for fusion reaction history measurement with high temporal resolution. The system is composed of plastic scintillator and nose cone, optical system and streak camera. We have applied this system on the SG-III prototype for fusion reaction rate measuring. For the first time, fusion reaction rate history have been measured for deuterium-tritium filled targets with neutrons yields about 10 10 . We have analyzed possible influence factor during fusion reaction rate measuring. It indicates that the instrument measures fusion reaction bang time at temporal resolutions as low as 30 ps.(authors)

  17. Sodium/water pool-deposit bed model of the CONACS code

    Peak, R.D.

    1983-01-01

    A new Pool-Bed model of the CONACS (Containment Analysis Code System) code represents a major advance over the pool models of other containment analysis code (NABE code of France, CEDAN code of Japan and CACECO and CONTAIN codes of the United States). This new model advances pool-bed modeling because of the number of significant materials and processes which are included with appropriate rigor. This CONACS pool-bed model maintains material balances for eight chemical species (C, H 2 O, Na, NaH, Na 2 O, Na 2 O 2 , Na 2 CO 3 and NaOH) that collect in the stationary liquid pool on the floor and in the desposit bed on the elevated shelf of the standard CONACS analysis cell

  18. Experimental studies on acoustic detection of sodium-water steam generator leaks in the USSR

    Petrenko, A.A.; Poplavsky, V.M.

    1990-01-01

    The paper reports that the acoustic leak indicators have been developed in two versions. The first one is based upon using the immersible acoustic hydrophones and the parallel frequency analysis of their signals. The second one uses the waveguide sensors with microprocessor system of noise signals processing. Brief description of both versions is given. The result of these systems tests at the experimental facilities, BN-600 and BOR-60 reactors are also provided. 4 refs, 15 figs

  19. Autoregressive techniques for acoustic detection of in-sodium water leaks

    Hayashi, K.

    1997-01-01

    We have been applied a background signal whitening filter built by univariate autoregressive model to the estimation problem of the leak start time and duration. In the 1995 present benchmark stage, we evaluated the method using acoustic signals from real hydrogen or water/steam injection experiments. The results show that the signal processing technique using this filter can detect reliability the leak signals with a sufficient signal-to-noise ratio. Even if the sensor signal contains non-boiling or non-leak high-amplitude pulses, they can be classified by spectral information. Especially, the feature signal made from the time-frequency spectrum of the filtered signal is very sensitive and useful. (author). 8 refs, 14 figs, 6 tabs

  20. Transient simulation of a helical-coil sodium/water steam generator

    Van Tuyle, G.J.; Iwashita, T.

    1982-01-01

    The MINET (Momentum Integral Network) code heat exchanger model was used to analyze transient test data provided by PNC of Japan. Testing of the MINET model is part of a larger effort to facilitate and validate the use of the SSC/MINET code for MONJU plant transient analysis. In MINET, a heat exchanger is modeled using one or more representative tubes, with each tube consisting of the fluid inside the tube, the tube wall, and the fluid outside that is associated with the tube. The heat exchanger tube is divided into one or more axial nodes of equal length. Five time dependent equations are utilized per node, including the wall heat conduction equation and donor-cell differenced conservation of mass and energy equations for the fluids on both sides of the tube. These nodal equations are used to constrain the tube wall temperature, fluid mass flow rates, and fluid enthalpies