WorldWideScience

Sample records for junction field-effect transistors

  1. Graphene junction field-effect transistor

    Science.gov (United States)

    Ou, Tzu-Min; Borsa, Tomoko; van Zeghbroeck, Bart

    2014-03-01

    We have demonstrated for the first time a novel graphene transistor gated by a graphene/semiconductor junction rather than an insulating gate. The transistor operates much like a semiconductor junction Field Effect Transistor (jFET) where the depletion layer charge in the semiconductor modulates the mobile charge in the channel. The channel in our case is the graphene rather than another semiconductor layer. An increased reverse bias of the graphene/n-silicon junction increases the positive charge in the depletion region and thereby reduces the total charge in the graphene. We fabricated individual graphene/silicon junctions as well as graphene jFETs (GjFETs) on n-type (4.5x1015 cm-3) silicon with Cr/Au electrodes and 3 μm gate length. As a control device, we also fabricated back-gated graphene MOSFETs using a 90nm SiO2 on a p-type silicon substrate (1019 cm-3) . The graphene was grown by APCVD on copper foil and transferred with PMMA onto the silicon substrate. The GjFET exhibited an on-off ratio of 3.75, an intrinsic graphene doping of 1.75x1012 cm-2, compared to 1.17x1013 cm-2 in the MOSFET, and reached the Dirac point at 13.5V. Characteristics of the junctions and transistors were measured as a function of temperature and in response to light. Experimental data and a comparison with simulations will be presented.

  2. Field emission current from a junction field-effect transistor

    Energy Technology Data Exchange (ETDEWEB)

    Monshipouri, Mahta; Abdi, Yaser, E-mail: y.abdi@ut.ac.ir [University of Tehran, Nano-Physics Research Laboratory, Department of Physics (Iran, Islamic Republic of)

    2015-04-15

    Fabrication of a titanium dioxide/carbon nanotube (TiO{sub 2}/CNT)-based transistor is reported. The transistor can be considered as a combination of a field emission transistor and a junction field-effect transistor. Using direct current plasma-enhanced chemical vapor deposition (DC-PECVD) technique, CNTs were grown on a p-typed (100)-oriented silicon substrate. The CNTs were then covered by TiO{sub 2} nanoparticles 2–5 nm in size, using an atmospheric pressure CVD technique. In this device, TiO{sub 2}/CNT junction is responsible for controlling the emission current. High on/off-current ratio and proper gate control are the most important advantages of device. A model based on Fowler–Nordheim equation is utilized for calculation of the emission current and the results are compared with experimental data. The effect of TiO{sub 2}/CNT hetero-structure is also investigated, and well modeled.

  3. Comparison between Field Effect Transistors and Bipolar Junction Transistors as Transducers in Electrochemical Sensors

    Science.gov (United States)

    Zafar, Sufi; Lu, Minhua; Jagtiani, Ashish

    2017-01-01

    Field effect transistors (FET) have been widely used as transducers in electrochemical sensors for over 40 years. In this report, a FET transducer is compared with the recently proposed bipolar junction transistor (BJT) transducer. Measurements are performed on two chloride electrochemical sensors that are identical in all details except for the transducer device type. Comparative measurements show that the transducer choice significantly impacts the electrochemical sensor characteristics. Signal to noise ratio is 20 to 2 times greater for the BJT sensor. Sensitivity is also enhanced: BJT sensing signal changes by 10 times per pCl, whereas the FET signal changes by 8 or less times. Also, sensor calibration curves are impacted by the transducer choice. Unlike a FET sensor, the calibration curve of the BJT sensor is independent of applied voltages. Hence, a BJT sensor can make quantitative sensing measurements with minimal calibration requirements, an important characteristic for mobile sensing applications. As a demonstration for mobile applications, these BJT sensors are further investigated by measuring chloride levels in artificial human sweat for potential cystic fibrosis diagnostic use. In summary, the BJT device is demonstrated to be a superior transducer in comparison to a FET in an electrochemical sensor. PMID:28134275

  4. Comparison between Field Effect Transistors and Bipolar Junction Transistors as Transducers in Electrochemical Sensors

    Science.gov (United States)

    Zafar, Sufi; Lu, Minhua; Jagtiani, Ashish

    2017-01-01

    Field effect transistors (FET) have been widely used as transducers in electrochemical sensors for over 40 years. In this report, a FET transducer is compared with the recently proposed bipolar junction transistor (BJT) transducer. Measurements are performed on two chloride electrochemical sensors that are identical in all details except for the transducer device type. Comparative measurements show that the transducer choice significantly impacts the electrochemical sensor characteristics. Signal to noise ratio is 20 to 2 times greater for the BJT sensor. Sensitivity is also enhanced: BJT sensing signal changes by 10 times per pCl, whereas the FET signal changes by 8 or less times. Also, sensor calibration curves are impacted by the transducer choice. Unlike a FET sensor, the calibration curve of the BJT sensor is independent of applied voltages. Hence, a BJT sensor can make quantitative sensing measurements with minimal calibration requirements, an important characteristic for mobile sensing applications. As a demonstration for mobile applications, these BJT sensors are further investigated by measuring chloride levels in artificial human sweat for potential cystic fibrosis diagnostic use. In summary, the BJT device is demonstrated to be a superior transducer in comparison to a FET in an electrochemical sensor.

  5. A novel 10-nm physical gate length double-gate junction field effect transistor

    Institute of Scientific and Technical Information of China (English)

    Hou Xiao-Yu; Huang Ru; Chen Gang; Liu Sheng; Zhang Xing; Yu Bin; Wang Yang-Yuan

    2008-01-01

    A novel double-gate (DG) junction field effect transistor (JFET) with depletion operation mode is proposed in this paper.Compared with the conventional DG MOSFET,the novel DG JFET can achieve excellent performance with square body design,which relaxes the requirement on silicon film thickness of DG devices.Moreover,due to the structural symmetry,both p-type and n-type devices can be realized on exactly the same structure,which greatly simplifies integration.It can reduce the delay by about 60% in comparison with the conventional DG MOSFETs.

  6. Fabrication and characterization of GaN junction field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, L.; Lester, L.F.; Baca, A.G.; Shul, R.J.; Chang, P.C.; Willison, C.L.; Mishra, U.K.; Denbaars, S.P.; Zolper, J.C.

    2000-01-11

    Junction field effect transistors (JFET) were fabricated on a GaN epitaxial structure grown by metal organic chemical vapor deposition. The DC and microwave characteristics, as well as the high temperature performance of the devices were studied. These devices exhibited excellent pinch-off and a breakdown voltage that agreed with theoretical predictions. An extrinsic transconductance (g{sub m}) of 48 mS/mm was obtained with a maximum drain current (I{sub D}) of 270 mA/mm. The microwave measurement showed an f{sub T} of 6 GHz and an f{sub max} of 12 GHz. Both the I{sub D} and the g{sub m} were found to decrease with increasing temperature, possibly due to lower electron mobility at elevated temperatures. These JFETs exhibited a significant current reduction after a high drain bias was applied, which was attributed to a partially depleted channel caused by trapped electrons in the semi-insulating GaN buffer layer.

  7. Applications, Prospects and Challenges of Silicon Carbide Junction Field Effect Transistor (SIC JFET

    Directory of Open Access Journals (Sweden)

    Frederick Ojiemhende Ehiagwina

    2016-09-01

    Full Text Available Properties of Silicon Carbide Junction Field Effect Transistor (SiC JFET such as high switching speed, low forward voltage drop and high temperature operation have attracted the interest of power electronic researchers and technologists, who for many years developed devices based on Silicon (Si.  A number of power system Engineers have made efforts to develop more robust equipment including circuits or modules with higher power density. However, it was realized that several available power semiconductor devices were approaching theoretical limits offered by Si material with respect to capability to block high voltage, provide low on-state voltage drop and switch at high frequencies. This paper presents an overview of the current applications of SiC JFET in circuits such as inverters, rectifiers and amplifiers. Other areas of application reviewed include; usage of the SiC JFET in pulse signal circuits and boost converters. Efforts directed toward mitigating the observed increase in electromagnetic interference were also discussed. It also presented some areas for further research, such as having more applications of SiC JFET in harsh, high temperature environment. More work is needed with regards to SiC JFET drivers so as to ensure stable and reliable operation, and reduction in the prices of SiC JFETs through mass production by industries.

  8. Tunnel Field-Effect Transistor with Epitaxially Grown Tunnel Junction Fabricated by Source/Drain-First and Tunnel-Junction-Last Processes

    Science.gov (United States)

    Morita, Yukinori; Mori, Takahiro; Migita, Shinji; Mizubayashi, Wataru; Tanabe, Akihito; Fukuda, Koichi; Masahara, Meishoku; Ota, Hiroyuki

    2013-04-01

    We fabricate p- and n-channel Si tunnel field-effect transistors (TFETs) with an epitaxially grown tunnel junction. In a novel source/drain-first and tunnel-junction-last fabrication process, a thin epitaxial undoped Si channel (epichannel) is deposited on a preferentially fabricated p- or n-type source area. The epichannel sandwiched by a gate insulator and a highly doped source well acts as a parallel-plate tunnel capacitor, which effectively multiplies drain current with an enlarged tunnel area. On the basis of its simple structure and easy fabrication, symmetric n- and p-transistor and complementary metal oxide semiconductor inverter operations were successfully demonstrated.

  9. Electrical detection of the biological interaction of a charged peptide via gallium arsenide junction-field-effect transistors

    OpenAIRE

    Lee, Kangho; Nair, Pradeep R.; Alam, Muhammad A.; Janes, David B.; Wampler, Heeyeon P; Zemlyanov, Dmitry; Ivanisevic, Albena

    2008-01-01

    GaAs junction-field-effect transistors (JFETs) are utilized to achieve label-free detection of biological interaction between a probe transactivating transcriptional activator (TAT) peptide and the target trans-activation-responsive (TAR) RNA. The TAT peptide is a short sequence derived from the human immunodeficiency virus-type 1 TAT protein. The GaAs JFETs are modified with a mixed adlayer of 1-octadecanethiol (ODT) and TAT peptide, with the ODT passivating the GaAs surface from polar ions ...

  10. Homo-junction ferroelectric field-effect-transistor memory device using solution-processed lithium-doped zinc oxide thin films

    KAUST Repository

    Nayak, Pradipta K.

    2012-06-22

    High performance homo-junction field-effect transistor memory devices were prepared using solution processed transparent lithium-doped zinc oxide thin films for both the ferroelectric and semiconducting active layers. A highest field-effect mobility of 8.7 cm2/Vs was obtained along with an Ion/Ioff ratio of 106. The ferroelectric thin filmtransistors showed a low sub-threshold swing value of 0.19 V/dec and a significantly reduced device operating voltage (±4 V) compared to the reported hetero-junction ferroelectrictransistors, which is very promising for low-power non-volatile memory applications.

  11. Electrical detection of the biological interaction of a charged peptide via gallium arsenide junction-field-effect transistors

    Science.gov (United States)

    Lee, Kangho; Nair, Pradeep R.; Alam, Muhammad A.; Janes, David B.; Wampler, Heeyeon P.; Zemlyanov, Dmitry Y.; Ivanisevic, Albena

    2008-06-01

    GaAs junction-field-effect transistors (JFETs) are utilized to achieve label-free detection of biological interaction between a probe transactivating transcriptional activator (TAT) peptide and the target trans-activation-responsive (TAR) RNA. The TAT peptide is a short sequence derived from the human immunodeficiency virus-type 1 TAT protein. The GaAs JFETs are modified with a mixed adlayer of 1-octadecanethiol (ODT) and TAT peptide, with the ODT passivating the GaAs surface from polar ions in physiological solutions and the TAT peptide providing selective binding sites for TAR RNA. The devices modified with the mixed adlayer exhibit a negative pinch-off voltage (VP) shift, which is attributed to the fixed positive charges from the arginine-rich regions in the TAT peptide. Immersing the modified devices into a TAR RNA solution results in a large positive VP shift (>1 V) and a steeper subthreshold slope (˜80 mV/decade), whereas "dummy" RNA induced a small positive VP shift (˜0.3 V) without a significant change in subthreshold slopes (˜330 mV/decade). The observed modulation of device characteristics is analyzed with analytical modeling and two-dimensional numerical device simulations to investigate the electronic interactions between the GaAs JFETs and biological molecules.

  12. Low-Frequency Noise Characterization of Ultra-shallow Gate N-channel Junction Field Effect Transistors

    NARCIS (Netherlands)

    Piccolo, G.; Sarubbi, F.; Vandamme, L.J.K.; Macucci, M.; Scholtes, T.L.M.; Nanver, L.K.

    2007-01-01

    A recently developed technique for ultra shallow pn junction formation has been applied for the fabrication of ring-gate n-channel junction field effect devices (JFET) devices. Several different geometries, gate formation parameters and channel doping profiles have been realized and characterized wi

  13. Tunneling field effect transistor technology

    CERN Document Server

    Chan, Mansun

    2016-01-01

    This book provides a single-source reference to the state-of-the art in tunneling field effect transistors (TFETs). Readers will learn the TFETs physics from advanced atomistic simulations, the TFETs fabrication process and the important roles that TFETs will play in enabling integrated circuit designs for power efficiency. · Provides comprehensive reference to tunneling field effect transistors (TFETs); · Covers all aspects of TFETs, from device process to modeling and applications; · Enables design of power-efficient integrated circuits, with low power consumption TFETs.

  14. Nanowire field effect transistors principles and applications

    CERN Document Server

    Jeong, Yoon-Ha

    2014-01-01

    “Nanowire Field Effect Transistor: Basic Principles and Applications” places an emphasis on the application aspects of nanowire field effect transistors (NWFET). Device physics and electronics are discussed in a compact manner, together with the p-n junction diode and MOSFET, the former as an essential element in NWFET and the latter as a general background of the FET. During this discussion, the photo-diode, solar cell, LED, LD, DRAM, flash EEPROM and sensors are highlighted to pave the way for similar applications of NWFET. Modeling is discussed in close analogy and comparison with MOSFETs. Contributors focus on processing, electrostatic discharge (ESD) and application of NWFET. This includes coverage of solar and memory cells, biological and chemical sensors, displays and atomic scale light emitting diodes. Appropriate for scientists and engineers interested in acquiring a working knowledge of NWFET as well as graduate students specializing in this subject.

  15. A Novel Super-Junction Lateral Double-Diffused Metal-Oxide-Semiconductor Field Effect Transistor with n-Type Step Doping Buffer Layer

    Institute of Scientific and Technical Information of China (English)

    CHENG Jian-Bing; ZHANG Do; DUAN Bao-Xing; LI Zhao-Ji

    2008-01-01

    A novel super-junction lateral double-diffused metal-nxide-semiconductor field effect transistor(SJ-LDMOSFET)with n-type step doping buffer layer is proposed.The step doping buffer layer almost completely eliminates the substrate-assisted depletion effect.modulates lateral electric field and achieves nearly uniform surface field.On the other hand,the buffer layer also provides another conductive path and reduces on-state resistance.In short,the proposed LDMOSFET improves trade-off performance between breakdown voltage (BV)and specific on-state resistance Ron,sp.Compared with the conventional SJ-LDMOSFET,the simulation results indicate that the BV of the SSJ-LDMOSFET is increased from saturation voltage 121.7 V to 644.9 V;at the same time,the specific when the drift region length and the step number are taken as 48μm and 3,respectively.

  16. Characterization, Modeling and Design Parameters Identification of Silicon Carbide Junction Field Effect Transistor for Temperature Sensor Applications

    Directory of Open Access Journals (Sweden)

    Sofiane Khachroumi

    2010-01-01

    Full Text Available Sensor technology is moving towards wide-band-gap semiconductors providing high temperature capable devices. Indeed, the higher thermal conductivity of silicon carbide, (three times more than silicon, permits better heat dissipation and allows better cooling and temperature management. Though many temperature sensors have already been published, little endeavours have been invested in the study of silicon carbide junction field effect devices (SiC-JFET as a temperature sensor. SiC-JFETs devices are now mature enough and it is close to be commercialized. The use of its specific properties versus temperatures is the major focus of this paper. The SiC-JFETs output current-voltage characteristics are characterized at different temperatures. The saturation current and its on-resistance versus temperature are successfully extracted. It is demonstrated that these parameters are proportional to the absolute temperature. A physics-based model is also presented. Relationships between on-resistance and saturation current versus temperature are introduced. A comparative study between experimental data and simulation results is conducted. Important to note, the proposed model and the experimental results reflect a successful agreement as far as a temperature sensor is concerned.

  17. Graphene field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, Dharmendar; Register, Leonard F; Banerjee, Sanjay K [Microelectronics Research Center, University of Texas at Austin, Austin, Texas 78758 (United States); Carpenter, Gary D [IBM Austin Research Labs, Austin, Texas 78728 (United States)

    2011-08-10

    Owing in part to scaling challenges for metal oxide semiconductor field-effect transistors (MOSFETs) and complementary metal oxide semiconductor (CMOS) logic, the semiconductor industry is placing an increased emphasis on emerging materials and devices that may provide improved MOSFET performance beyond the 22 nm node, or provide novel functionality for, e.g. 'beyond CMOS' devices. Graphene, with its novel and electron-hole symmetric band structure and its high carrier mobilities and thermal velocities, is one such material that has garnered a great deal of interest for both purposes. Single and few layer carbon sheets have been fabricated by a variety of techniques including mechanical exfoliation and chemical vapour deposition, and field-effect transistors have been demonstrated with room-temperature mobilities as high as 10 000 cm{sup 2} V{sup -1} s{sup -1}. But graphene is a gapless semiconductor and gate control of current is challenging, off-state leakage currents are high, and current does not readily saturate with drain voltage. However, various ways to overcome, adapt to, or even embrace this property are now being considered for device applications. In this work we explore through illustrative examples the potential of and challenges to graphene use for conventional and novel device applications. (topical review)

  18. Graphene field-effect transistors

    Science.gov (United States)

    Reddy, Dharmendar; Register, Leonard F.; Carpenter, Gary D.; Banerjee, Sanjay K.

    2011-08-01

    Owing in part to scaling challenges for metal oxide semiconductor field-effect transistors (MOSFETs) and complementary metal oxide semiconductor (CMOS) logic, the semiconductor industry is placing an increased emphasis on emerging materials and devices that may provide improved MOSFET performance beyond the 22 nm node, or provide novel functionality for, e.g. 'beyond CMOS' devices. Graphene, with its novel and electron-hole symmetric band structure and its high carrier mobilities and thermal velocities, is one such material that has garnered a great deal of interest for both purposes. Single and few layer carbon sheets have been fabricated by a variety of techniques including mechanical exfoliation and chemical vapour deposition, and field-effect transistors have been demonstrated with room-temperature mobilities as high as 10 000 cm2 V-1 s-1. But graphene is a gapless semiconductor and gate control of current is challenging, off-state leakage currents are high, and current does not readily saturate with drain voltage. However, various ways to overcome, adapt to, or even embrace this property are now being considered for device applications. In this work we explore through illustrative examples the potential of and challenges to graphene use for conventional and novel device applications.

  19. Photovoltage field-effect transistors

    Science.gov (United States)

    Adinolfi, Valerio; Sargent, Edward H.

    2017-02-01

    The detection of infrared radiation enables night vision, health monitoring, optical communications and three-dimensional object recognition. Silicon is widely used in modern electronics, but its electronic bandgap prevents the detection of light at wavelengths longer than about 1,100 nanometres. It is therefore of interest to extend the performance of silicon photodetectors into the infrared spectrum, beyond the bandgap of silicon. Here we demonstrate a photovoltage field-effect transistor that uses silicon for charge transport, but is also sensitive to infrared light owing to the use of a quantum dot light absorber. The photovoltage generated at the interface between the silicon and the quantum dot, combined with the high transconductance provided by the silicon device, leads to high gain (more than 104 electrons per photon at 1,500 nanometres), fast time response (less than 10 microseconds) and a widely tunable spectral response. Our photovoltage field-effect transistor has a responsivity that is five orders of magnitude higher at a wavelength of 1,500 nanometres than that of previous infrared-sensitized silicon detectors. The sensitization is achieved using a room-temperature solution process and does not rely on traditional high-temperature epitaxial growth of semiconductors (such as is used for germanium and III–V semiconductors). Our results show that colloidal quantum dots can be used as an efficient platform for silicon-based infrared detection, competitive with state-of-the-art epitaxial semiconductors.

  20. Nanowire Field-Effect Transistors: Sensing Simplicity?

    NARCIS (Netherlands)

    Mescher, M.

    2014-01-01

    Silicon nanowires are structures made from silicon with at least one spatial dimension in the nanometer regime (1-100 nm). From these nanowires, silicon nanowire field-effect transistors can be constructed. Since their introduction in 2001 silicon nanowire field-effect transistors have been studied

  1. Organic tunnel field effect transistors

    KAUST Repository

    Tietze, Max Lutz

    2017-06-29

    Various examples are provided for organic tunnel field effect transistors (OTFET), and methods thereof. In one example, an OTFET includes a first intrinsic layer (i-layer) of organic semiconductor material disposed over a gate insulating layer; source (or drain) contact stacks disposed on portions of the first i-layer; a second i-layer of organic semiconductor material disposed on the first i-layer surrounding the source (or drain) contact stacks; an n-doped organic semiconductor layer disposed on the second i-layer; and a drain (or source) contact layer disposed on the n-doped organic semiconductor layer. The source (or drain) contact stacks can include a p-doped injection layer, a source (or drain) contact layer, and a contact insulating layer. In another example, a method includes disposing a first i-layer over a gate insulating layer; forming source or drain contact stacks; and disposing a second i-layer, an n-doped organic semiconductor layer, and a drain or source contact.

  2. Integrated ZnO Nano-Electron-Emitter with Self-Modulated Parasitic Tunneling Field Effect Transistor at the Surface of the p-Si/ZnO Junction

    Science.gov (United States)

    Cao, Tao; Luo, Laitang; Huang, Yifeng; Ye, Bing; She, Juncong; Deng, Shaozhi; Chen, Jun; Xu, Ningsheng

    2016-09-01

    The development of high performance nano-electron-emitter arrays with well reliability still proves challenging. Here, we report a featured integrated nano-electron-emitter. The vertically aligned nano-emitter consists of two segments. The top segment is an intrinsically lightly n-type doped ZnO nano-tip, while the bottom segment is a heavily p-type doped Si nano-pillar (denoted as p-Si/ZnO nano-emitter). The anode voltage not only extracted the electron emission from the emitter apex but also induced the inter-band electron tunneling at the surface of the p-Si/ZnO nano-junction. The designed p-Si/ZnO emitter is equivalent to a ZnO nano-tip individually ballasted by a p-Si/ZnO diode and a parasitic tunneling field effect transistor (TFET) at the surface of the p-Si/ZnO junction. The parasitic TFET provides a channel for the supply of emitting electron, while the p-Si/ZnO diode is benefit for impeding the current overloading and prevent the emitters from a catastrophic breakdown. Well repeatable and stable field emission current were obtained from the p-Si/ZnO nano-emitters. High performance nano-emitters was developed using diamond-like-carbon coated p-Si/ZnO tip array (500 × 500), i.e., 178 μA (4.48 mA/cm2) at 75.7 MV/m.

  3. Integrated ZnO Nano-Electron-Emitter with Self-Modulated Parasitic Tunneling Field Effect Transistor at the Surface of the p-Si/ZnO Junction.

    Science.gov (United States)

    Cao, Tao; Luo, Laitang; Huang, Yifeng; Ye, Bing; She, Juncong; Deng, Shaozhi; Chen, Jun; Xu, Ningsheng

    2016-09-22

    The development of high performance nano-electron-emitter arrays with well reliability still proves challenging. Here, we report a featured integrated nano-electron-emitter. The vertically aligned nano-emitter consists of two segments. The top segment is an intrinsically lightly n-type doped ZnO nano-tip, while the bottom segment is a heavily p-type doped Si nano-pillar (denoted as p-Si/ZnO nano-emitter). The anode voltage not only extracted the electron emission from the emitter apex but also induced the inter-band electron tunneling at the surface of the p-Si/ZnO nano-junction. The designed p-Si/ZnO emitter is equivalent to a ZnO nano-tip individually ballasted by a p-Si/ZnO diode and a parasitic tunneling field effect transistor (TFET) at the surface of the p-Si/ZnO junction. The parasitic TFET provides a channel for the supply of emitting electron, while the p-Si/ZnO diode is benefit for impeding the current overloading and prevent the emitters from a catastrophic breakdown. Well repeatable and stable field emission current were obtained from the p-Si/ZnO nano-emitters. High performance nano-emitters was developed using diamond-like-carbon coated p-Si/ZnO tip array (500 × 500), i.e., 178 μA (4.48 mA/cm(2)) at 75.7 MV/m.

  4. Integrated ZnO Nano-Electron-Emitter with Self-Modulated Parasitic Tunneling Field Effect Transistor at the Surface of the p-Si/ZnO Junction

    Science.gov (United States)

    Cao, Tao; Luo, Laitang; Huang, Yifeng; Ye, Bing; She, Juncong; Deng, Shaozhi; Chen, Jun; Xu, Ningsheng

    2016-01-01

    The development of high performance nano-electron-emitter arrays with well reliability still proves challenging. Here, we report a featured integrated nano-electron-emitter. The vertically aligned nano-emitter consists of two segments. The top segment is an intrinsically lightly n-type doped ZnO nano-tip, while the bottom segment is a heavily p-type doped Si nano-pillar (denoted as p-Si/ZnO nano-emitter). The anode voltage not only extracted the electron emission from the emitter apex but also induced the inter-band electron tunneling at the surface of the p-Si/ZnO nano-junction. The designed p-Si/ZnO emitter is equivalent to a ZnO nano-tip individually ballasted by a p-Si/ZnO diode and a parasitic tunneling field effect transistor (TFET) at the surface of the p-Si/ZnO junction. The parasitic TFET provides a channel for the supply of emitting electron, while the p-Si/ZnO diode is benefit for impeding the current overloading and prevent the emitters from a catastrophic breakdown. Well repeatable and stable field emission current were obtained from the p-Si/ZnO nano-emitters. High performance nano-emitters was developed using diamond-like-carbon coated p-Si/ZnO tip array (500 × 500), i.e., 178 μA (4.48 mA/cm2) at 75.7 MV/m. PMID:27654068

  5. Nanowire Field-Effect Transistors: Sensing Simplicity?

    OpenAIRE

    Mescher, M

    2014-01-01

    Silicon nanowires are structures made from silicon with at least one spatial dimension in the nanometer regime (1-100 nm). From these nanowires, silicon nanowire field-effect transistors can be constructed. Since their introduction in 2001 silicon nanowire field-effect transistors have been studied because of their promising application as selective sensors for biological and chemical species. Their large surface-to-volume ratio promises an increased sensitivity compared to conventional, plan...

  6. SEMICONDUCTOR DEVICES: Humidity sensitive organic field effect transistor

    Science.gov (United States)

    Murtaza, I.; Karimov, Kh S.; Ahmad, Zubair; Qazi, I.; Mahroof-Tahir, M.; Khan, T. A.; Amin, T.

    2010-05-01

    This paper reports the experimental results for the humidity dependent properties of an organic field effect transistor. The organic field effect transistor was fabricated on thoroughly cleaned glass substrate, in which the junction between the metal gate and the organic channel plays the role of gate dielectric. Thin films of organic semiconductor copper phthalocynanine (CuPc) and semitransparent Al were deposited in sequence by vacuum thermal evaporation on the glass substrate with preliminarily deposited Ag source and drain electrodes. The output and transfer characteristics of the fabricated device were performed. The effect of humidity on the drain current, drain current-drain voltage relationship, and threshold voltage was investigated. It was observed that humidity has a strong effect on the characteristics of the organic field effect transistor.

  7. Ideal Channel Field Effect Transistors

    Science.gov (United States)

    2010-03-01

    transistors and composite channel InAlAs/InGaAs/lnP/InAlAs high electron mobility transistors ( HEMTs ), which have taken the full advantage of the matched...lattice constant (or pseudomorphic growth). However, for the most popular wide bandgap semiconductor GaN and SiC, the lattice mismatch between GaN ...critical thickness of InN on GaN is about one monolayer. To marry the advantages offered by both narrow bandgap and wide bandgap semiconductors, we

  8. Fundamentals of nanoscaled field effect transistors

    CERN Document Server

    Chaudhry, Amit

    2013-01-01

    Fundamentals of Nanoscaled Field Effect Transistors gives comprehensive coverage of the fundamental physical principles and theory behind nanoscale transistors. The specific issues that arise for nanoscale MOSFETs, such as quantum mechanical tunneling and inversion layer quantization, are fully explored. The solutions to these issues, such as high-κ technology, strained-Si technology, alternate devices structures and graphene technology are also given. Some case studies regarding the above issues and solution are also given in the book. In summary, this book: Covers the fundamental principles behind nanoelectronics/microelectronics Includes chapters devoted to solutions tackling the quantum mechanical effects occurring at nanoscale Provides some case studies to understand the issue mathematically Fundamentals of Nanoscaled Field Effect Transistors is an ideal book for researchers and undergraduate and graduate students in the field of microelectronics, nanoelectronics, and electronics.

  9. Vertically Integrated Multiple Nanowire Field Effect Transistor.

    Science.gov (United States)

    Lee, Byung-Hyun; Kang, Min-Ho; Ahn, Dae-Chul; Park, Jun-Young; Bang, Tewook; Jeon, Seung-Bae; Hur, Jae; Lee, Dongil; Choi, Yang-Kyu

    2015-12-09

    A vertically integrated multiple channel-based field-effect transistor (FET) with the highest number of nanowires reported ever is demonstrated on a bulk silicon substrate without use of wet etching. The driving current is increased by 5-fold due to the inherent vertically stacked five-level nanowires, thus showing good feasibility of three-dimensional integration-based high performance transistor. The developed fabrication process, which is simple and reproducible, is used to create multiple stiction-free and uniformly sized nanowires with the aid of the one-route all-dry etching process (ORADEP). Furthermore, the proposed FET is revamped to create nonvolatile memory with the adoption of a charge trapping layer for enhanced practicality. Thus, this research suggests an ultimate design for the end-of-the-roadmap devices to overcome the limits of scaling.

  10. Proposal of spin complementary field effect transistor

    Science.gov (United States)

    Kunihashi, Yoji; Kohda, Makoto; Sanada, Haruki; Gotoh, Hideki; Sogawa, Tetsuomi; Nitta, Junsaku

    2012-03-01

    Spin complementary field effect transistor is proposed on the basis of gate-controlled persistent spin helix (PSH) states. Uniaxial effective magnetic field in the PSH state creates coherent spin propagation with or without precession. By the gate control of the Rashba spin-orbit interaction, the PSH state can be reversed to the inverted PSH state. Switching between two PSH states enables complementary output depending on the channel direction. Our proposed device could be a reconfigurable minimum unit of the spin-based logic circuit.

  11. Hysteresis modeling in graphene field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Winters, M.; Rorsman, N. [Department of Microtechnology and Nanoscience, Chalmers University of Technology, 412-96 Göteborg (Sweden); Sveinbjörnsson, E. Ö. [Science Institute, University of Iceland, IS-107 Reykjavik (Iceland)

    2015-02-21

    Graphene field effect transistors with an Al{sub 2}O{sub 3} gate dielectric are fabricated on H-intercalated bilayer graphene grown on semi-insulating 4H-SiC by chemical vapour deposition. DC measurements of the gate voltage v{sub g} versus the drain current i{sub d} reveal a severe hysteresis of clockwise orientation. A capacitive model is used to derive the relationship between the applied gate voltage and the Fermi energy. The electron transport equations are then used to calculate the drain current for a given applied gate voltage. The hysteresis in measured data is then modeled via a modified Preisach kernel.

  12. Field-effect transistors (2nd revised and enlarged edition)

    Science.gov (United States)

    Bocharov, L. N.

    The design, principle of operation, and principal technical characteristics of field-effect transistors produced in the USSR are described. Problems related to the use of field-effect transistors in various radioelectronic devices are examined, and tables of parameters and mean statistical characteristics are presented for the main types of field-effect transistors. Methods for calculating various circuit components are discussed and illustrated by numerical examples.

  13. Polycrystalline silicon ion sensitive field effect transistors

    Science.gov (United States)

    Yan, F.; Estrela, P.; Mo, Y.; Migliorato, P.; Maeda, H.; Inoue, S.; Shimoda, T.

    2005-01-01

    We report the operation of polycrystalline silicon ion sensitive field effect transistors. These devices can be fabricated on inexpensive disposable substrates such as glass or plastics and are, therefore, promising candidates for low cost single-use intelligent multisensors. In this work we have developed an extended gate structure with a Si3N4 sensing layer. Nearly ideal pH sensitivity (54mV /pH) and stable operation have been achieved. Temperature effects have been characterized. A penicillin sensor has been fabricated by functionalizing the sensing area with penicillinase. The sensitivity to penicillin G is about 10mV/mM, in solutions with concentration lower than the saturation value, which is about 7 mM.

  14. Theoretical calculation of performance enhancement in lattice-matched SiGeSn/GeSn p-channel tunneling field-effect transistor with type-II staggered tunneling junction

    Science.gov (United States)

    Wang, Hongjuan; Han, Genquan; Wang, Yibo; Peng, Yue; Liu, Yan; Zhang, Chunfu; Zhang, Jincheng; Hu, Shengdong; Hao, Yue

    2016-04-01

    In this work, a lattice-matched SiGeSn/GeSn heterostructure p-channel tunneling field-effect transistor (hetero-PTFET) with a type-II staggered tunneling junction (TJ) is investigated theoretically. Lattice matching and type-II band alignment at the Γ-point is obtained at the SiGeSn/GeSn interface by tuning Sn and Si compositions. A steeper subthreshold swing (SS) and a higher on state current (I ON) are demonstrated in SiGeSn/GeSn hetero-PTFET than in GeSn homo-PTFET. Si0.31Ge0.49Sn0.20/Ge0.88Sn0.12 hetero-PTFET achieves a 2.3-fold higher I ON than Ge0.88Sn0.12 homo-PTFET at V DD of 0.3 V. Hetero-PTFET achieves a more abrupt hole profile and a higher carrier density near TJ than the homo-PTFET, which contributes to the significantly enhanced band-to-band tunneling (BTBT) rate and tunneling current in hetero-PTFET.

  15. Silicon nanowire field effect transistor for biosensing

    Science.gov (United States)

    Chen, Yu

    Detection and recognition of chemical ions and biological molecules are important in basic science as well as in pharmacology and medicine. Nanotechnology has made it possible to greatly enhance detection sensitivity through the use of nanowires, nanotubes, nanocrystals, nanocantilevers, and quantum dots as sensing platforms. In this work silicon nanowires are used as the conductance channel between the source and drain of a FET (field effect transistor) device and the biomolecular binding on the surface of nanowire modifies the conductance like a change in gate voltage. Due to the high surface-to-volume ratio and unique character of the silicon nanowires, this device has significant advantages in real-time, label-free and highly sensitive detection of a wide range of species, including proteins, nucleic acids and other small molecules. Here we present a biosensor fabricated from CMOS (complementary metal-oxide-semiconductor) compatible top-down methods including electron beam lithography. This method enables scalable manufacturing of multiple sensor arrays with high efficiency. In a systematic study of the device characteristics with different wire widths, we have found the sensitivity of the device increases when wire width decreases. By operating the device in appropriate bias region, the sensitivity of the device can be improved without doping or high temperature annealing. Not only can this device be used to detect the concentration of proteins and metabolites like urea or glucose, but also dynamic information like the dissociation constant can be extracted from the measurement. The device is also used to detect the clinically related cancer antigen CA 15.3 and shows potential application in cancer studies.

  16. Chemically modified field effect transistors with nitrite or fluoride selectivity

    NARCIS (Netherlands)

    Antonisse, Martijn M.G.; Snellink-Ruël, Bianca H.M.; Engbersen, Johan F.J.; Reinhoudt, David N.

    1998-01-01

    Polysiloxanes with different types of polar substituents are excellent membrane materials for nitrite and fluoride selective chemically modified field effect transistors (CHEMFETs). Nitrite selectivity has been introduced by incorporation of a cobalt porphyrin into the membrane; fluoride selectivity

  17. Chemically modified field effect transistors with nitrite or fluoride selectivity

    NARCIS (Netherlands)

    Antonisse, M.M.G.; Ruel, Bianca H.M.; Engbersen, Johannes F.J.; Reinhoudt, David

    1998-01-01

    Polysiloxanes with different types of polar substituents are excellent membrane materials for nitrite and fluoride selective chemically modified field effect transistors (CHEMFETs). Nitrite selectivity has been introduced by incorporation of a cobalt porphyrin into the membrane; fluoride selectivity

  18. Field-effect transistors on tetracene single crystals

    NARCIS (Netherlands)

    De Boer, R.W.I.; Klapwijk, T.M.; Morpurgo, A.F

    2003-01-01

    We report on the fabrication and electrical characterization of field-effect transistors at the surface of tetracene single crystals. We find that the mobility of these transistors reaches the room-temperature value of 0.4 cm2/V s. The nonmonotonous temperature dependence of the mobility, its weak g

  19. Progresses in organic field-effect transistors and molecular electronics

    Institute of Scientific and Technical Information of China (English)

    Wu Weiping; Xu Wei; Hu Wenping; Liu Yunqi; Zhu Daoben

    2006-01-01

    In the past years,organic semiconductors have been extensively investigated as electronic materials for organic field-effect transistors (OFETs).In this review,we briefly summarize the current status of organic field-effect transistors including materials design,device physics,molecular electronics and the applications of carbon nanotubes in molecular electronics.Future prospects and investigations required to improve the OFET performance are also involved.

  20. Transistor-like behavior of single metalloprotein junctions.

    Science.gov (United States)

    Artés, Juan M; Díez-Pérez, Ismael; Gorostiza, Pau

    2012-06-13

    Single protein junctions consisting of azurin bridged between a gold substrate and the probe of an electrochemical tunneling microscope (ECSTM) have been obtained by two independent methods that allowed statistical analysis over a large number of measured junctions. Conductance measurements yield (7.3 ± 1.5) × 10(-6)G(0) in agreement with reported estimates using other techniques. Redox gating of the protein with an on/off ratio of 20 was demonstrated and constitutes a proof-of-principle of a single redox protein field-effect transistor.

  1. Polyphosphonium-based ion bipolar junction transistors.

    Science.gov (United States)

    Gabrielsson, Erik O; Tybrandt, Klas; Berggren, Magnus

    2014-11-01

    Advancements in the field of electronics during the past few decades have inspired the use of transistors in a diversity of research fields, including biology and medicine. However, signals in living organisms are not only carried by electrons but also through fluxes of ions and biomolecules. Thus, in order to implement the transistor functionality to control biological signals, devices that can modulate currents of ions and biomolecules, i.e., ionic transistors and diodes, are needed. One successful approach for modulation of ionic currents is to use oppositely charged ion-selective membranes to form so called ion bipolar junction transistors (IBJTs). Unfortunately, overall IBJT device performance has been hindered due to the typical low mobility of ions, large geometries of the ion bipolar junction materials, and the possibility of electric field enhanced (EFE) water dissociation in the junction. Here, we introduce a novel polyphosphonium-based anion-selective material into npn-type IBJTs. The new material does not show EFE water dissociation and therefore allows for a reduction of junction length down to 2 μm, which significantly improves the switching performance of the ion transistor to 2 s. The presented improvement in speed as well the simplified design will be useful for future development of advanced iontronic circuits employing IBJTs, for example, addressable drug-delivery devices.

  2. Cylindrical-shaped nanotube field effect transistor

    KAUST Repository

    Hussain, Muhammad Mustafa

    2015-12-29

    A cylindrical-shaped nanotube FET may be manufactured on silicon (Si) substrates as a ring etched into a gate stack and filled with semiconductor material. An inner gate electrode couples to a region of the gate stack inside the inner circumference of the ring. An outer gate electrode couples to a region of the gate stack outside the outer circumference of the ring. The multi-gate cylindrical-shaped nanotube FET operates in volume inversion for ring widths below 15 nanometers. The cylindrical-shaped nanotube FET demonstrates better short channel effect (SCE) mitigation and higher performance (I.sub.on/I.sub.off) than conventional transistor devices. The cylindrical-shaped nanotube FET may also be manufactured with higher yields and cheaper costs than conventional transistors.

  3. Carbon nanotubes field effect transistors biosensors

    OpenAIRE

    Martínez, M.T.; Tseng, Y. C.; Ormategui, N.; Loinaz, I.; Eritja Casadellà, Ramón; Salvador, Juan Pablo; Marco, María Pilar; Bokor, J.

    2012-01-01

    [EN] Carbon nanotube transistor arrays (CNTFETs) were used as biosensors to detect NA hybridization and to recognize two anabolic steroids, stanozolol (Stz) and methylboldenone (MB). Single strand DNA and antibodies specific for STz and MB were immobilized on the carbon nanotubes (CNTs) in situ in the device using two different approaches: direct noncovalent bonding of antibodies to the devices and covalently trough a polymer previously attached to the CNTFETs. A new approach to ensure specif...

  4. Carbon nanotubes field effect transistors biosensors

    OpenAIRE

    Martínez, M. T.; Y.C. Tseng; N. Ormategui; I. Loinaz; Eritja Casadellà, Ramón; Salvador, Juan Pablo; Marco, María Pilar; Bokor, J.

    2012-01-01

    [EN] Carbon nanotube transistor arrays (CNTFETs) were used as biosensors to detect NA hybridization and to recognize two anabolic steroids, stanozolol (Stz) and methylboldenone (MB). Single strand DNA and antibodies specific for STz and MB were immobilized on the carbon nanotubes (CNTs) in situ in the device using two different approaches: direct noncovalent bonding of antibodies to the devices and covalently trough a polymer previously attached to the CNTFETs. A new approach to ensure specif...

  5. Organic semiconductors for organic field-effect transistors

    Directory of Open Access Journals (Sweden)

    Yoshiro Yamashita

    2009-01-01

    Full Text Available The advantages of organic field-effect transistors (OFETs, such as low cost, flexibility and large-area fabrication, have recently attracted much attention due to their electronic applications. Practical transistors require high mobility, large on/off ratio, low threshold voltage and high stability. Development of new organic semiconductors is key to achieving these parameters. Recently, organic semiconductors have been synthesized showing comparable mobilities to amorphous-silicon-based FETs. These materials make OFETs more attractive and their applications have been attempted. New organic semiconductors resulting in high-performance FET devices are described here and the relationship between transistor characteristics and chemical structure is discussed.

  6. Vertical Ge and GeSn heterojunction gate-all-around tunneling field effect transistors

    Science.gov (United States)

    Schulze, Jörg; Blech, Andreas; Datta, Arnab; Fischer, Inga A.; Hähnel, Daniel; Naasz, Sandra; Rolseth, Erlend; Tropper, Eva-Maria

    2015-08-01

    We present experimental results on the fabrication and characterization of vertical Ge and GeSn heterojunction Tunneling Field Effect Transistors (TFETs). A gate-all-around process with mesa diameters down to 70 nm is used to reduce leakage currents and improve electrostatic control of the gate over the transistor channel. An ION = 88.4 μA/μm at VDS = VG = -2 V is obtained for a TFET with a 10 nm Ge0.92Sn0.08 layer at the source/channel junction. We discuss further possibilities for device improvements.

  7. Carbon nanotubes field effect transistors biosensors

    Directory of Open Access Journals (Sweden)

    M.P. Marco

    2012-03-01

    Full Text Available Carbon nanotube transistor arrays (CNTFETs wereused as biosensors to detect DNA hybridization andto recognize two anabolic steroids, stanozolol (Stzand methylboldenone (MB. Single strand DNA andantibodies specific for STz and MB were immobilizedon the carbon nanotubes (CNTs in situ in the deviceusing two different approaches: direct noncovalentbonding of antibodies to the devices and covalentlytrough a polymer previously attached to theCNTFETs. A new approach to ensure specificadsorption of the biomolecules to the nanotubeswas developed. The polymer poly(methylmethacrylate0.8-co-poly (ethyleneglycolmethacrylate0.8-co-N-succinimidyl methacrylate0.1was synthesized and bonded noncovalently to thenanotube. Aminated single-strand DNA or antibodiesspecific for Stz and MB were then attached covalentlyto the polymer. Statistically significant changes wereobserved in key transistor parameters for both DNAhybridization and steroids recognition. Regardingthe detection mechanism, in addition to chargetransfer, Schottky barrier, SB, modification, andscattering potential reported by other authors, anelectron/hole trapping mechanism leading tohysteresis modification has been determined. Thepresence of polymer seems to hinder the modulationof the electrode-CNT contact.

  8. SiC Optically Modulated Field-Effect Transistor

    Science.gov (United States)

    Tabib-Azar, Massood

    2009-01-01

    An optically modulated field-effect transistor (OFET) based on a silicon carbide junction field-effect transistor (JFET) is under study as, potentially, a prototype of devices that could be useful for detecting ultraviolet light. The SiC OFET is an experimental device that is one of several devices, including commercial and experimental photodiodes, that were initially evaluated as detectors of ultraviolet light from combustion and that could be incorporated into SiC integrated circuits to be designed to function as combustion sensors. The ultraviolet-detection sensitivity of the photodiodes was found to be less than desired, such that it would be necessary to process their outputs using high-gain amplification circuitry. On the other hand, in principle, the function of the OFET could be characterized as a combination of detection and amplification. In effect, its sensitivity could be considerably greater than that of a photodiode, such that the need for amplification external to the photodetector could be reduced or eliminated. The experimental SiC OFET was made by processes similar to JFET-fabrication processes developed at Glenn Research Center. The gate of the OFET is very long, wide, and thin, relative to the gates of typical prior SiC JFETs. Unlike in prior SiC FETs, the gate is almost completely transparent to near-ultraviolet and visible light. More specifically: The OFET includes a p+ gate layer less than 1/4 m thick, through which photons can be transported efficiently to the p+/p body interface. The gate is relatively long and wide (about 0.5 by 0.5 mm), such that holes generated at the body interface form a depletion layer that modulates the conductivity of the channel between the drain and the source. The exact physical mechanism of modulation of conductivity is a subject of continuing research. It is known that injection of minority charge carriers (in this case, holes) at the interface exerts a strong effect on the channel, resulting in amplification

  9. Classical Gradual-Channel Modeling of Graphene Field-Effect Transistors (FETs)

    Science.gov (United States)

    2010-08-01

    application of a high-powered many-body analysis of the electronic degrees of freedom, which, in turn, predicts ferromagnetism , superconductivity , charge...metal- oxide semiconductor field-effect transistors (MOSFETs), high electron mobility transistors (HEMTs), metal semiconductor field-effect transistors...V current versus voltage MESFET metal semiconductor field-effect transistor MOSFET metal- oxide semiconductor field-effect transistor RF radio

  10. Field-effect transistor self-electrooptic effect device integrated photodiode, quantum well modulator and transistor

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D.A.B.; Feuer, M.D.; Chang, T.Y.; Shunk, S.C.; Henry, J.E.; Burrows, D.J.; Chemla, D.S.

    1989-03-01

    The authors propose and demonstrate the integration of a photodiode, a quantum-confined Stark effect quantum well optical modulator and a metal-semiconductor field-effect transistor (MESFET), to make a field-effect transistor self-electrooptic effect device. This integration allows optical inputs and outputs on the surface of a GaAs-integrated circuit chip, compatible with standard MESFET processing. As an illustration of feasibility, the authors demonstrate optical signal amplification with a single MESFET.

  11. Single event burnout sensitivity of embedded field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Koga, R.; Crain, S.H.; Crawford, K.B.; Yu, P.; Gordon, M.J.

    1999-12-01

    Observations of single event burnout (SEB) in embedded field effect transistors are reported. Both SEB and other single event effects are presented for several pulse width modulation and high frequency devices. The microscope has been employed to locate and to investigate the damaged areas. A model of the damage mechanism based on the results so obtained is described.

  12. Durable chemical sensors based on field-effect transistors

    NARCIS (Netherlands)

    Reinhoudt, D.N.

    1995-01-01

    The design of durable chemical sensors based on field-effect transistors (FETs) is described. After modification of an ion-sensitive FET (ISFET) with a polysiloxane membrane matrix, it is possible to attach all electroactive components covalently. Preliminary results of measurements with a sodium-se

  13. Conductance switching in organic ferroelectric field-effect transistors

    NARCIS (Netherlands)

    Asadi, K.; Blom, P.W.M.; Leeuw, D.M. de

    2011-01-01

    Staggered bottom-contact top-gate organic ferroelectric field-effect transistors are fabricated with poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) as ferroelectric gate and poly[bis(4-phenyl)(2,4,6- trimethylphenyl)amine] as semiconductor. Polarization reversal of the ferroelectric gate

  14. π-Conjugated Organic Semiconductors for Field-Effect Transistors

    Institute of Scientific and Technical Information of China (English)

    LIU Yun-qi

    2005-01-01

    @@ 1Results and Discussion Organic semiconductors employed as active layers in field-effect transistors (FETs) are of great current interest because such FETs can potentially be fabricated at low cost, over large areas, and on flexible substrates. Such facile fabrication approaches offer a significant advantage over silicon technology in numerous applications.

  15. Nanoscaled biological gated field effect transistors for cytogenetic analysis

    DEFF Research Database (Denmark)

    Kwasny, Dorota; Dimaki, Maria; Andersen, Karsten Brandt;

    2014-01-01

    Cytogenetic analysis is the study of chromosome structure and function, and is often used in cancer diagnosis, as many chromosome abnormalities are linked to the onset of cancer. A novel label free detection method for chromosomal translocation analysis using nanoscaled field effect transistors...

  16. Reference field effect transistor based on chemically modified ISFETs

    NARCIS (Netherlands)

    Skowronska-Ptasinska, Maria; Wal, van der Peter D.; Berg, van den Albert; Bergveld, Piet; Sudhölter, Ernst J.R.; Reinhoudt, David N.

    1990-01-01

    Different hydrophobic polymers were used for chemical modification of ion-sensitive field effect transistors (ISFETs) in order to prepare a reference FET (REFET). Chemical attachment of the polymer to the ISFET gate results in a long lifetime of the device. Properties of polyacrylate (polyACE) REFET

  17. Reaching saturation in patterned source vertical organic field effect transistors

    Science.gov (United States)

    Greenman, Michael; Sheleg, Gil; Keum, Chang-min; Zucker, Jonathan; Lussem, Bjorn; Tessler, Nir

    2017-05-01

    Like most of the vertical transistors, the Patterned Source Vertical Organic Field Effect Transistor (PS-VOFET) does not exhibit saturation in the output characteristics. The importance of achieving a good saturation is demonstrated in a vertical organic light emitting transistor; however, this is critical for any application requiring the transistor to act as a current source. Thereafter, a 2D simulation tool was used to explain the physical mechanisms that prevent saturation as well as to suggest ways to overcome them. We found that by isolating the source facet from the drain-source electric field, the PS-VOFET architecture exhibits saturation. The process used for fabricating such saturation-enhancing structure is then described. The new device demonstrated close to an ideal saturation with only 1% change in the drain-source current over a 10 V change in the drain-source voltage.

  18. Vertically aligned carbon nanotube field-effect transistors

    KAUST Repository

    Li, Jingqi

    2012-10-01

    Vertically aligned carbon nanotube field-effect transistors (CNTFETs) have been developed using pure semiconducting carbon nanotubes. The source and drain were vertically stacked, separated by a dielectric, and the carbon nanotubes were placed on the sidewall of the stack to bridge the source and drain. Both the effective gate dielectric and gate electrode were normal to the substrate surface. The channel length is determined by the dielectric thickness between source and drain electrodes, making it easier to fabricate sub-micrometer transistors without using time-consuming electron beam lithography. The transistor area is much smaller than the planar CNTFET due to the vertical arrangement of source and drain and the reduced channel area. © 2012 Elsevier Ltd. All rights reserved.

  19. Contact engineering in organic field-effect transistors

    Directory of Open Access Journals (Sweden)

    Chuan Liu

    2015-03-01

    Full Text Available Organic field-effect transistors (OFETs are promising for numerous potential applications but suffer from poor charge injection, such that their performance is severely limited. Recent efforts in lowering contact resistance have led to significantly improved field-effect mobility of OFETs, up to 100 times higher, as the results of careful choice of contact materials and/or chemical treatment of contact electrodes. Here we review the innovative developments of contact engineering and focus on the mechanisms behind them. Further improvement toward Ohmic contact can be expected along with the rapid advance in material research, which will also benefit other organic and electronic devices.

  20. Organic single-crystal field-effect transistors

    Directory of Open Access Journals (Sweden)

    Colin Reese

    2007-03-01

    Full Text Available Organic molecular crystals hold great promise for the rational development of organic semiconductor materials. Their long-range order not only reveals the performance limits of organic materials, but also provides unique insight into their intrinsic transport properties. The field-effect transistor (FET has served as a versatile tool for electrical characterization of many facets of their performance. In the last few years, breakthroughs in single-crystal FET fabrication techniques have enabled the realization of field-effect mobilities far surpassing amorphous Si, observation of the Hall effect in an organic material, and the study of transport as an explicit function of molecular packing and chemical structure.

  1. A scheme for a topological insulator field effect transistor

    Science.gov (United States)

    Vali, Mehran; Dideban, Daryoosh; Moezi, Negin

    2015-05-01

    We propose a scheme for a topological insulator field effect transistor. The idea is based on the gate voltage control of the Dirac fermions in a ferromagnetic topological insulator channel with perpendicular magnetization connecting to two metallic topological insulator leads. Our theoretical analysis shows that the proposed device displays a switching effect with high on/off current ratio and a negative differential conductance with a good peak to valley ratio.

  2. Transit-Time Spin Field-Effect-Transistor

    OpenAIRE

    Appelbaum, Ian; Monsma, Douwe

    2007-01-01

    We propose and analyze a four-terminal metal-semiconductor device that uses hot-electron transport through thin ferromagnetic films to inject and detect a charge-coupled spin current transported through the conduction band of an arbitrary semiconductor. This provides the possibility of realizing a spin field-effect-transistor in Si, using electrostatic transit-time control in a perpendicular magnetic field, rather than Rashba effect with spin-orbit interaction.

  3. Field-effect tunneling transistor based on vertical graphene heterostructures

    OpenAIRE

    Britnell, L.; Gorbachev, R. V.; Jalil, R.; Belle, B. D.; Schedin, F.; Mishchenko, A.; Georgiou, T; Katsnelson, M. I.; Eaves, L.; Morozov, S. V.; Peres, N. M. R.; Leist, J.; Geim, A. K.; Novoselov, K.S.; Ponomarenko, L. A.

    2012-01-01

    We report a bipolar field effect tunneling transistor that exploits to advantage the low density of states in graphene and its one atomic layer thickness. Our proof-of-concept devices are graphene heterostructures with atomically thin boron nitride acting as a tunnel barrier. They exhibit room temperature switching ratios ~50, a value that can be enhanced further by optimizing the device structure. These devices have potential for high frequency operation and large scale integration.

  4. Advances in organic field-effect transistors and integrated circuits

    Institute of Scientific and Technical Information of China (English)

    WANG Hong; JI ZhuoYu; LIU Ming; SHANG LiWei; LIU Ge; LIU XingHua; LIU Jiang; PENG YingQuan

    2009-01-01

    Organic field-effect transistors (OFETs) have received significant research interest because of their promising applications in low cast, lager area, plastic circuits, and tremendous progress has been made in materials, device performance, OFETs based circuits in recent years.In this article we intro-duce the advances in organic semiconductor materials, OFETs based integrating techniques, and in particular highlight the recent progress.Finally, the prospects and problems of OFETs are discussed.

  5. Organic Field-effect Transistors Based on Tetrathiafulvalene Derivatives

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    1 Restults Tetrathiafulvalene (TTF) and its derivatives have been extensively investigated in the field of organic conductors and superconductors since 1973. Recently, their application in organic field-effect transistors (OFETs) has attracted considerable attention. So far, on the one hand, the fabrication techniques of the TTF-based FETs have been primarily limited to high vacuum evaporation, which is a relatively expensive process. On the other hand, low FET performances, such as the low on/off ratio...

  6. Graphene-based field-effect transistor biosensors

    Energy Technology Data Exchange (ETDEWEB)

    Chen; , Junhong; Mao, Shun; Lu, Ganhua

    2017-06-14

    The disclosure provides a field-effect transistor (FET)-based biosensor and uses thereof. In particular, to FET-based biosensors using thermally reduced graphene-based sheets as a conducting channel decorated with nanoparticle-biomolecule conjugates. The present disclosure also relates to FET-based biosensors using metal nitride/graphene hybrid sheets. The disclosure provides a method for detecting a target biomolecule in a sample using the FET-based biosensor described herein.

  7. Field-effect transistors assembled from functionalized carbon nanotubes

    OpenAIRE

    Klinke, Christian; Hannon, James B.; Afzali, Ali; Avouris, Phaedon

    2006-01-01

    We have fabricated field effect transistors from carbon nanotubes using a novel selective placement scheme. We use carbon nanotubes that are covalently bound to molecules containing hydroxamic acid functionality. The functionalized nanotubes bind strongly to basic metal oxide surfaces, but not to silicon dioxide. Upon annealing, the functionalization is removed, restoring the electronic properties of the nanotubes. The devices we have fabricated show excellent electrical characteristics.

  8. Advances in organic field-effect transistors and integrated circuits

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Organic field-effect transistors (OFETs) have received significant research interest because of their promising applications in low cast, lager area, plastic circuits, and tremendous progress has been made in materials, device performance, OFETs based circuits in recent years. In this article we introduce the advances in organic semiconductor materials, OFETs based integrating techniques, and in particular highlight the recent progress. Finally, the prospects and problems of OFETs are discussed.

  9. Exfoliated multilayer MoTe2 field-effect transistors

    Science.gov (United States)

    Fathipour, S.; Ma, N.; Hwang, W. S.; Protasenko, V.; Vishwanath, S.; Xing, H. G.; Xu, H.; Jena, D.; Appenzeller, J.; Seabaugh, A.

    2014-11-01

    The properties of multilayer exfoliated MoTe2 field-effect transistors (FETs) on SiO2 were investigated for channel thicknesses from 6 to 44 monolayers (MLs). All transistors showed p-type conductivity at zero back-gate bias. For channel thicknesses of 8 ML or less, the transistors exhibited ambipolar characteristics. ON/OFF current ratio was greatest, 1 × 105, for the transistor with the thinnest channel, 6 ML. Devices showed a clear photoresponse to wavelengths between 510 and 1080 nm at room temperature. Temperature-dependent current-voltage measurements were performed on a FET with 30 layers of MoTe2. When the channel is turned-on and p-type, the temperature dependence is barrier-limited by the Au/Ti/MoTe2 contact with a hole activation energy of 0.13 eV. A long channel transistor model with Schottky barrier contacts is shown to be consistent with the common-source characteristics.

  10. Electromechanical field effect transistors based on multilayer phosphorene nanoribbons

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Z.T., E-mail: jiangzhaotan@hotmail.com; Lv, Z.T.; Zhang, X.D.

    2017-06-21

    Based on the tight-binding Hamiltonian approach, we demonstrate that the electromechanical field effect transistors (FETs) can be realized by using the multilayer phosphorene nanoribbons (PNRs). The synergistic combination of the electric field and the external strains can establish the on–off switching since the electric field can shift or split the energy band, and the mechanical strains can widen or narrow the band widths. This kind of multilayer PNR FETs, much solider than the monolayer PNR one and more easily biased by different electric fields, has more transport channels consequently leading to the higher on–off current ratio or the higher sensitivity to the electric fields. Meanwhile, the strain-induced band-flattening will be beneficial for improving the flexibility in designing the electromechanical FETs. In addition, such electromechanical FETs can act as strain-controlled FETs or mechanical detectors for detecting the strains, indicating their potential applications in nano- and micro-electromechanical fields. - Highlights: • Electromechanical transistors are designed with multilayer phosphorene nanoribbons. • Electromechanical synergistic effect can establish the on–off switching more flexibly. • Multilayer transistors, solider and more easily biased, has more transport channels. • Electromechanical transistors can act as strain-controlled transistors or mechanical detectors.

  11. Irradiation of graphene field effect transistors with highly charged ions

    Science.gov (United States)

    Ernst, P.; Kozubek, R.; Madauß, L.; Sonntag, J.; Lorke, A.; Schleberger, M.

    2016-09-01

    In this work, graphene field-effect transistors are used to detect defects due to irradiation with slow, highly charged ions. In order to avoid contamination effects, a dedicated ultra-high vacuum set up has been designed and installed for the in situ cleaning and electrical characterization of graphene field-effect transistors during irradiation. To investigate the electrical and structural modifications of irradiated graphene field-effect transistors, their transfer characteristics as well as the corresponding Raman spectra are analyzed as a function of ion fluence for two different charge states. The irradiation experiments show a decreasing mobility with increasing fluences. The mobility reduction scales with the potential energy of the ions. In comparison to Raman spectroscopy, the transport properties of graphene show an extremely high sensitivity with respect to ion irradiation: a significant drop of the mobility is observed already at fluences below 15 ions/μm2, which is more than one order of magnitude lower than what is required for Raman spectroscopy.

  12. Organic field-effect transistors using single crystals

    Directory of Open Access Journals (Sweden)

    Tatsuo Hasegawa and Jun Takeya

    2009-01-01

    Full Text Available Organic field-effect transistors using small-molecule organic single crystals are developed to investigate fundamental aspects of organic thin-film transistors that have been widely studied for possible future markets for 'plastic electronics'. In reviewing the physics and chemistry of single-crystal organic field-effect transistors (SC-OFETs, the nature of intrinsic charge dynamics is elucidated for the carriers induced at the single crystal surfaces of molecular semiconductors. Materials for SC-OFETs are first reviewed with descriptions of the fabrication methods and the field-effect characteristics. In particular, a benchmark carrier mobility of 20–40 cm2 Vs−1, achieved with thin platelets of rubrene single crystals, demonstrates the significance of the SC-OFETs and clarifies material limitations for organic devices. In the latter part of this review, we discuss the physics of microscopic charge transport by using SC-OFETs at metal/semiconductor contacts and along semiconductor/insulator interfaces. Most importantly, Hall effect and electron spin resonance (ESR measurements reveal that interface charge transport in molecular semiconductors is properly described in terms of band transport and localization by charge traps.

  13. Interdigitated Extended Gate Field Effect Transistor Without Reference Electrode

    Science.gov (United States)

    Ali, Ghusoon M.

    2017-02-01

    An interdigitated extended gate field effect transistor (IEGFET) has been proposed as a modified pH sensor structure of an extended gate field effect transistor (EGFET). The reference electrode and the extended gate in the conventional device have been replaced by a single interdigitated extended gate. A metal-semiconductor-metal interdigitated extended gate containing two multi-finger Ni electrodes based on zinc oxide (ZnO) thin film as a pH-sensitive membrane. ZnO thin film was grown on a p-type Si (100) substrate by the sol-gel technique. The fabricated extended gate is connected to a commercial metal-oxide-semiconductor field-effect transistor device in CD4007UB. The experimental data show that this structure has real time and linear pH voltage and current sensitivities in a concentration range between pH 4 and 11. The voltage and current sensitivities are found to be about 22.4 mV/pH and 45 μA/pH, respectively. Reference electrode elimination makes the IEGFET device simple to fabricate, easy to carry out the measurements, needing a small volume of solution to test and suitable for disposable biosensor applications. Furthermore, this uncomplicated structure could be extended to fabricate multiple ions microsensors and lab-on-chip devices.

  14. TOPICAL REVIEW: Organic field-effect transistors using single crystals

    Science.gov (United States)

    Hasegawa, Tatsuo; Takeya, Jun

    2009-04-01

    Organic field-effect transistors using small-molecule organic single crystals are developed to investigate fundamental aspects of organic thin-film transistors that have been widely studied for possible future markets for 'plastic electronics'. In reviewing the physics and chemistry of single-crystal organic field-effect transistors (SC-OFETs), the nature of intrinsic charge dynamics is elucidated for the carriers induced at the single crystal surfaces of molecular semiconductors. Materials for SC-OFETs are first reviewed with descriptions of the fabrication methods and the field-effect characteristics. In particular, a benchmark carrier mobility of 20-40 cm2 Vs-1, achieved with thin platelets of rubrene single crystals, demonstrates the significance of the SC-OFETs and clarifies material limitations for organic devices. In the latter part of this review, we discuss the physics of microscopic charge transport by using SC-OFETs at metal/semiconductor contacts and along semiconductor/insulator interfaces. Most importantly, Hall effect and electron spin resonance (ESR) measurements reveal that interface charge transport in molecular semiconductors is properly described in terms of band transport and localization by charge traps.

  15. Electrical interfacing of neurotransmitter receptor and field effect transistor

    Science.gov (United States)

    Peitz, I.; Fromherz, P.

    2009-10-01

    The interfacing of a ligand-gated ion channel to a transistor is studied. It relies on the transduction of ion current to a voltage in a cell-transistor junction. For the first time, a genetically modified cell is used without external driving voltage as applied by a patch-pipette. Using a core-coat conductor model, we show that an autonomous dynamics gives rise to a signal if a driving voltage is provided by potassium channels, and if current compensation is avoided by an inhomogeneous activation of channels. In a proof-of-principle experiment, we transfect HEK293 cells with the serotonin receptor 5-HT3A and the potassium channel Kv1.3. The interfacing is characterized under voltage-clamp with a negative transistor signal for activated 5-HT3A and a positive signal for activated Kv1.3. Without patch-pipette, a biphasic transient is induced by serotonin. The positive wave is assigned to 5-HT3A receptors in the free membrane that drive a potassium outward current through the adherent membrane. The negative wave is attributed to 5-HT3A receptors in the adherent membrane that are activated with a delay due to serotonin diffusion. The implementation of a receptor-cell-transistor device is a fundamental step in the development of biosensors that combine high specificity and universal microelectronic readout.

  16. Imperfect two-dimensional topological insulator field-effect transistors

    Science.gov (United States)

    Vandenberghe, William G.; Fischetti, Massimo V.

    2017-01-01

    To overcome the challenge of using two-dimensional materials for nanoelectronic devices, we propose two-dimensional topological insulator field-effect transistors that switch based on the modulation of scattering. We model transistors made of two-dimensional topological insulator ribbons accounting for scattering with phonons and imperfections. In the on-state, the Fermi level lies in the bulk bandgap and the electrons travel ballistically through the topologically protected edge states even in the presence of imperfections. In the off-state the Fermi level moves into the bandgap and electrons suffer from severe back-scattering. An off-current more than two-orders below the on-current is demonstrated and a high on-current is maintained even in the presence of imperfections. At low drain-source bias, the output characteristics are like those of conventional field-effect transistors, at large drain-source bias negative differential resistance is revealed. Complementary n- and p-type devices can be made enabling high-performance and low-power electronic circuits using imperfect two-dimensional topological insulators. PMID:28106059

  17. Field-effect transistors based on cubic indium nitride.

    Science.gov (United States)

    Oseki, Masaaki; Okubo, Kana; Kobayashi, Atsushi; Ohta, Jitsuo; Fujioka, Hiroshi

    2014-02-04

    Although the demand for high-speed telecommunications has increased in recent years, the performance of transistors fabricated with traditional semiconductors such as silicon, gallium arsenide, and gallium nitride have reached their physical performance limits. Therefore, new materials with high carrier velocities should be sought for the fabrication of next-generation, ultra-high-speed transistors. Indium nitride (InN) has attracted much attention for this purpose because of its high electron drift velocity under a high electric field. Thick InN films have been applied to the fabrication of field-effect transistors (FETs), but the performance of the thick InN transistors was discouraging, with no clear linear-saturation output characteristics and poor on/off current ratios. Here, we report the epitaxial deposition of ultrathin cubic InN on insulating oxide yttria-stabilized zirconia substrates and the first demonstration of ultrathin-InN-based FETs. The devices exhibit high on/off ratios and low off-current densities because of the high quality top and bottom interfaces between the ultrathin cubic InN and oxide insulators. This first demonstration of FETs using a ultrathin cubic indium nitride semiconductor will thus pave the way for the development of next-generation high-speed electronics.

  18. Investigation of tunnel field-effect transistors as a capacitor-less memory cell

    Science.gov (United States)

    Biswas, Arnab; Dagtekin, Nilay; Grabinski, Wladyslaw; Bazigos, Antonios; Le Royer, Cyrille; Hartmann, Jean-Michel; Tabone, Claude; Vinet, Maud; Ionescu, Adrian M.

    2014-03-01

    In this work, we report experimental results on the use of tunnel field-effect transistors as capacitorless dynamic random access memory cells, implemented as double-gate fully depleted silicon-on-insulator devices. The devices have an asymmetric design, with a partial overlap of the top gate (LG) and with a total overlap of the back gate over the channel region (LG + LIN). A potential well is created by biasing the back gate (VBG) in accumulation, while the front gate (VFG) is in inversion. Holes from the p+ source are injected by the forward-biased p+ i junction and stored in the electrically induced potential well.

  19. Graphene-graphite oxide field-effect transistors.

    Science.gov (United States)

    Standley, Brian; Mendez, Anthony; Schmidgall, Emma; Bockrath, Marc

    2012-03-14

    Graphene's high mobility and two-dimensional nature make it an attractive material for field-effect transistors. Previous efforts in this area have used bulk gate dielectric materials such as SiO(2) or HfO(2). In contrast, we have studied the use of an ultrathin layered material, graphene's insulating analogue, graphite oxide. We have fabricated transistors comprising single or bilayer graphene channels, graphite oxide gate insulators, and metal top-gates. The graphite oxide layers show relatively minimal leakage at room temperature. The breakdown electric field of graphite oxide was found to be comparable to SiO(2), typically ~1-3 × 10(8) V/m, while its dielectric constant is slightly higher, κ ≈ 4.3.

  20. Biomolecular detection using a metal semiconductor field effect transistor

    Science.gov (United States)

    Estephan, Elias; Saab, Marie-Belle; Buzatu, Petre; Aulombard, Roger; Cuisinier, Frédéric J. G.; Gergely, Csilla; Cloitre, Thierry

    2010-04-01

    In this work, our attention was drawn towards developing affinity-based electrical biosensors, using a MESFET (Metal Semiconductor Field Effect Transistor). Semiconductor (SC) surfaces must be prepared before the incubations with biomolecules. The peptides route was adapted to exceed and bypass the limits revealed by other types of surface modification due to the unwanted unspecific interactions. As these peptides reveal specific recognition of materials, then controlled functionalization can be achieved. Peptides were produced by phage display technology using a library of M13 bacteriophage. After several rounds of bio-panning, the phages presenting affinities for GaAs SC were isolated; the DNA of these specific phages were sequenced, and the peptide with the highest affinity was synthesized and biotinylated. To explore the possibility of electrical detection, the MESFET fabricated with the GaAs SC were used to detect the streptavidin via the biotinylated peptide in the presence of the bovine Serum Albumin. After each surface modification step, the IDS (current between the drain and the source) of the transistor was measured and a decrease in the intensity was detected. Furthermore, fluorescent microscopy was used in order to prove the specificity of this peptide and the specific localisation of biomolecules. In conclusion, the feasibility of producing an electrical biosensor using a MESFET has been demonstrated. Controlled placement, specific localization and detection of biomolecules on a MESFET transistor were achieved without covering the drain and the source. This method of functionalization and detection can be of great utility for biosensing application opening a new way for developing bioFETs (Biomolecular Field-Effect Transistor).

  1. Pentacene Organic-Thin-Film Field-Effect Transistors

    Institute of Scientific and Technical Information of China (English)

    张素梅; 石家纬; 刘明大; 李靖; 郭树旭; 王伟

    2004-01-01

    We have fabricated organic thin-film transistors using the small-molecule polycyclic aromatic hydrocarbon pentacene as an active material. Devices were fabricated on glass substrates by using rf-magnetron sputtered amorphous aluminium as the gate electrode, and gelatinized polyimide as the gate dielectric with physical vapour grown pentacene thin films pasted on it as the active layer, then using rf-magnetron sputtered amorphous aluminium as the source and drain contacts. Field effect mobility and threshold voltage is 0.092 cm2 /Vs and 14.5 V,respectively. On-off current ratio is nearly 103.

  2. High-transconductance graphene solution-gated field effect transistors

    Science.gov (United States)

    Hess, L. H.; Hauf, M. V.; Seifert, M.; Speck, F.; Seyller, T.; Stutzmann, M.; Sharp, I. D.; Garrido, J. A.

    2011-07-01

    In this work, we report on the electronic properties of solution-gated field effect transistors (SGFETs) fabricated using large-area graphene. Devices prepared both with epitaxially grown graphene on SiC as well as with chemical vapor deposition grown graphene on Cu exhibit high transconductances, which are a consequence of the high mobility of charge carriers in graphene and the large capacitance at the graphene/water interface. The performance of graphene SGFETs, in terms of gate sensitivity, is compared to other SGFET technologies and found to be clearly superior, confirming the potential of graphene SGFETs for sensing applications in electrolytic environments.

  3. Carbon Nanotube Field-Effect Transistor for DNA Sensing

    Science.gov (United States)

    Xuan, Chu T.; Thuy, Nguyen T.; Luyen, Tran T.; Huyen, Tran T. T.; Tuan, Mai A.

    2017-01-01

    A field-effect transistor (FET) using carbon nanotubes (CNTs) as the conducting channel (CNTFET) has been developed, designed such that the CNT conducting channel (15 μm long, 700 μm wide) is directly exposed to medium containing target deoxyribonucleic acid (DNA). The CNTFET operates at high ON-current of 1.91 μA, ON/OFF-current ratio of 1.2 × 105, conductance of 4.3 μS, and leakage current of 16.4 pA. We present initial trials showing the response of the CNTFET to injection of target DNA into aqueous medium.

  4. Pressure sensing by flexible, organic, field effect transistors

    Science.gov (United States)

    Manunza, I.; Sulis, A.; Bonfiglio, A.

    2006-10-01

    A mechanical sensor based on a pentacene field effect transistor has been fabricated. The pressure dependence of the output current has been investigated by applying a mechanical stimulus by means of a pressurized air flow. Experimental results show a reversible current dependence on pressure. Data analysis suggests that variations of threshold voltage, mobility and contact resistance are responsible for current variations. Thanks to the flexibility of the substrate and the low cost of the technology, this device opens the way for flexible mechanical sensors that can be used in a variety of innovative applications such as e-textiles and robotic interfaces.

  5. Plasmon Field Effect Transistor for Plasmon to Electric Conversion and Amplification.

    Science.gov (United States)

    Shokri Kojori, Hossein; Yun, Ju-Hyung; Paik, Younghun; Kim, Joondong; Anderson, Wayne A; Kim, Sung Jin

    2016-01-13

    Direct coupling of electronic excitations of optical energy via plasmon resonances opens the door to improving gain and selectivity in various optoelectronic applications. We report a new device structure and working mechanisms for plasmon resonance energy detection and electric conversion based on a thin film transistor device with a metal nanostructure incorporated in it. This plasmon field effect transistor collects the plasmonically induced hot electrons from the physically isolated metal nanostructures. These hot electrons contribute to the amplification of the drain current. The internal electric field and quantum tunneling effect at the metal-semiconductor junction enable highly efficient hot electron collection and amplification. Combined with the versatility of plasmonic nanostructures in wavelength tunability, this device architecture offers an ultrawide spectral range that can be used in various applications.

  6. Single-WalledCarbon Nanotube Networked Field-Effect Transistors Functionalized with Thiolated Heme for NO2 Sensing

    Institute of Scientific and Technical Information of China (English)

    魏昂; 李维维; 汪静霞; 龙庆; 王钊; 熊莉; 董晓臣; 黄维

    2011-01-01

    The gas sensing properties of the single-walled carbon nanotube networked field-effect transistors for NO2 are investigated. After the modification of the gold contact electrodes of the carbon nanotube transistors with the thiolated heme, the NO2 sensing results indicate that the sensing sensitivity of the modified transistors is enhanced greatly and the sensing limit can reach below Woppb. It is also proposed that the mechanism of the sensitivity enhancement for NO2 detection mainly results from the modulation of the Schottky energy barrier at the Au/CNTs junction upon thiolated heme facilitated NO2 adsorption.%The gas sensing properties of the single-walled carbon nanotube networked field-effect transistors for NO2 are investigated.After the modification of the gold contact electrodes of the carbon nanotube transistors with the thiolated heme,the NO2 sensing results indicate that the sensing sensitivity of the modified transistors is enhanced greatly and the sensing limit can reach below 100ppb.It is also proposed that the mechanism of the sensitivity enhancement for NO2 detection mainly results from the modulation of the Schottky energy barrier at the Au/CNTs junction upon thiolated heme facilitated NO2 adsorption.

  7. Preparation of organic thin-film field effect transistor

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The organic thin-film field effect transistor was prepared through vacuum deposition by using teflon as di-electric material. Indium-tin-oxide acted as the source and drain electrodes. Copper phthalocyanine and teflon were used as the semiconductor layer and dielectric layer, respectively. The gate electrode was made of Ag. The channel length between the source and drain was 50 μm. After preparing the source and drain electrodes by lithography, the copper phthalocyanine layer, teflon layer and Ag layerwere prepared by vacuum deposition sequentially. The field effect electron mobility of the device reached 1.1×10ˉ6 cm2/(V@s), and the on/off current ratio reached 500.

  8. Infrared light gated MoS₂ field effect transistor.

    Science.gov (United States)

    Fang, Huajing; Lin, Ziyuan; Wang, Xinsheng; Tang, Chun-Yin; Chen, Yan; Zhang, Fan; Chai, Yang; Li, Qiang; Yan, Qingfeng; Chan, H L W; Dai, Ji-Yan

    2015-12-14

    Molybdenum disulfide (MoS₂) as a promising 2D material has attracted extensive attentions due to its unique physical, optical and electrical properties. In this work, we demonstrate an infrared (IR) light gated MoS₂ transistor through a device composed of MoS₂ monolayer and a ferroelectric single crystal Pb(Mg(1/3)Nb(2/3))O₃-PbTiO₃ (PMN-PT). With a monolayer MoS₂ onto the top surface of (111) PMN-PT crystal, the drain current of MoS₂ channel can be modulated with infrared illumination and this modulation process is reversible. Thus, the transistor can work as a new kind of IR photodetector with a high IR responsivity of 114%/Wcm⁻². The IR response of MoS₂ transistor is attributed to the polarization change of PMN-PT single crystal induced by the pyroelectric effect which results in a field effect. Our result promises the application of MoS₂ 2D material in infrared optoelectronic devices. Combining with the intrinsic photocurrent feature of MoS₂ in the visible range, the MoS₂ on ferroelectric single crystal may be sensitive to a broadband wavelength of light.

  9. Ferroelectric Field-Effect Transistor Differential Amplifier Circuit Analysis

    Science.gov (United States)

    Phillips, Thomas A.; MacLeod, Todd C.; Ho, Fat D.

    2008-01-01

    There has been considerable research investigating the Ferroelectric Field-Effect Transistor (FeFET) in memory circuits. However, very little research has been performed in applying the FeFET to analog circuits. This paper investigates the use of FeFETs in a common analog circuit, the differential amplifier. The two input Metal-Oxide-Semiconductor (MOS) transistors in a general MOS differential amplifier circuit are replaced with FeFETs. Resistors are used in place of the other three MOS transistors. The FeFET model used in the analysis has been previously reported and was based on experimental device data. Because of the FeFET hysteresis, the FeFET differential amplifier has four different operating modes depending on whether the FeFETs are positively or negatively polarized. The FeFET differential amplifier operation in the different modes was analyzed by calculating the amplifier voltage transfer and gain characteristics shown in figures 2 through 5. Comparisons were made between the FeFET differential amplifier and the standard MOS differential amplifier. Possible applications and benefits of the FeFET differential amplifier are discussed.

  10. Charge Transport in Hybrid Halide Perovskite Field-Effect Transistors

    Science.gov (United States)

    Jurchescu, Oana

    Hybrid organic-inorganic trihalide perovskite (HTP) materials exhibit a strong optical absorption, tunable band gap, long carrier lifetimes and fast charge carrier transport. These remarkable properties, coupled with their reduced complexity processing, make the HTPs promising contenders for large scale, low-cost thin film optoelectronic applications. But in spite of the remarkable demonstrations of high performance solar cells, light-emitting diodes and field-effect transistor devices, all of which took place in a very short time period, numerous questions related to the nature and dynamics of the charge carriers and their relation to device performance, stability and reliability still remain. This presentation describes the electrical properties of HTPs evaluated from field-effect transistor measurements. The electrostatic gating of provides an unique platform for the study of intrinsic charge transport in these materials, and, at the same time, expand the use of HTPs towards switching electronic devices, which have not been explored previously. We fabricated FETs on SiO2 and polymer dielectrics from spin coating, thermal evaporation and spray deposition and compare their properties. CH3NH3PbI3-xClx can reach balanced electron and hole mobilities of 10 cm2/Vs upon tuning the thin-film microstructure, injection and the defect density at the semiconductor/dielectric interface. The work was performed in collaboration with Yaochuan Mei (Wake Forest University), Chuang Zhang, and Z. Valy Vardeny (University of Utah). The work is supported by ONR Grant N00014-15-1-2943.

  11. Dimensionality of charge transport in organic field-effect transistors

    Science.gov (United States)

    Sharma, A.; van Oost, F. W. A.; Kemerink, M.; Bobbert, P. A.

    2012-06-01

    Application of a gate bias to an organic field-effect transistor leads to accumulation of charges in the organic semiconductor within a thin region near the gate dielectric. An important question is whether the charge transport in this region can be considered two-dimensional, or whether the possibility of charge motion in the third dimension, perpendicular to the accumulation layer, plays a crucial role. In order to answer this question we have performed Monte Carlo simulations of charge transport in organic field-effect transistor structures with varying thickness of the organic layer, taking into account all effects of energetic disorder and Coulomb interactions. We show that with increasing thickness of the semiconductor layer the source-drain current monotonically increases for weak disorder, whereas for strong disorder the current first increases and then decreases. Similarly, for a fixed layer thickness the mobility may either increase or decrease with increasing gate bias. We explain these results by the enhanced effect of state filling on the current for strong disorder, which competes with the effects of Coulomb interactions and charge motion in the third dimension. Our conclusion is that apart from the situation of a single monolayer, charge transport in an organic semiconductor layer should be considered three-dimensional, even at high gate bias.

  12. Potential of carbon nanotube field effect transistors for analogue circuits

    KAUST Repository

    Hayat, Khizar

    2013-05-11

    This Letter presents a detailed comparison of carbon nanotube field effect transistors (CNFETs) and metal oxide semiconductor field effect transistors (MOSFETs) with special focus on carbon nanotube FET\\'s potential for implementing analogue circuits in the mm-wave and sub-terahertz range. The latest CNFET lithographic dimensions place it at-par with complementary metal oxide semiconductor in terms of current handling capability, whereas the forecasted improvement in the lithography enables the CNFETs to handle more than twice the current of MOSFETs. The comparison of RF parameters shows superior performance of CNFETs with a g m , f T and f max of 2.7, 2.6 and 4.5 times higher, respectively. MOSFET- and CNFET-based inverter, three-stage ring oscillator and LC oscillator have been designed and compared as well. The CNFET-based inverters are found to be ten times faster, the ring oscillator demonstrates three times higher oscillation frequency and CNFET-based LC oscillator also shows improved performance than its MOSFET counterpart.

  13. Photojunction Field-Effect Transistor Based on a Colloidal Quantum Dot Absorber Channel Layer

    KAUST Repository

    Adinolfi, Valerio

    2015-01-27

    © 2015 American Chemical Society. The performance of photodetectors is judged via high responsivity, fast speed of response, and low background current. Many previously reported photodetectors based on size-tuned colloidal quantum dots (CQDs) have relied either on photodiodes, which, since they are primary photocarrier devices, lack gain; or photoconductors, which provide gain but at the expense of slow response (due to delayed charge carrier escape from sensitizing centers) and an inherent dark current vs responsivity trade-off. Here we report a photojunction field-effect transistor (photoJFET), which provides gain while breaking prior photoconductors\\' response/speed/dark current trade-off. This is achieved by ensuring that, in the dark, the channel is fully depleted due to a rectifying junction between a deep-work-function transparent conductive top contact (MoO3) and a moderately n-type CQD film (iodine treated PbS CQDs). We characterize the rectifying behavior of the junction and the linearity of the channel characteristics under illumination, and we observe a 10 μs rise time, a record for a gain-providing, low-dark-current CQD photodetector. We prove, using an analytical model validated using experimental measurements, that for a given response time the device provides a two-orders-of-magnitude improvement in photocurrent-to-dark-current ratio compared to photoconductors. The photoJFET, which relies on a junction gate-effect, enriches the growing family of CQD photosensitive transistors.

  14. Dielectric influence on IV curve of graphene field effect transistor

    Science.gov (United States)

    Shostachenko, Stanislav A.; Zakharchenko, Roman V.; Zebrev, Gennady I.; Stanishevskiy, Yaroslav M.; Kargin, Nikolay I.

    2016-12-01

    In this article, we have studied the influence of Si3N4 and SiO2 thin film gate dielectrics on the current-voltage characteristics of the graphene-based transistor. The test structure of graphene transistor was fabricated with the top and back gate. Graphene has been produced by chemical vapor deposition, and then transferred to the silicon dioxide on a silicon wafer. The channel of the transistor has been formed by etching in oxygen plasma through a photolithographic mask. Metals electrodes of the drain, source, and gate were deposited by resistive evaporation in a vacuum. It was used titanium / aluminum with a thickness of 50/200 nm. In the case of the back gate, silicon dioxide was used, obtained by thermal oxidation of the silicon substrate. For top gate was used silicon nitride deposited by plasma chemical deposition. It was demonstrated that field effect is more pronounced for the case of SiO2 back gate compare to the Si3N4 top gate. For the SiO2 back gate we have observed that the source- drain current decreases, from 2 mA to 3 mA, with increasing the gate voltage, from 0 to 40 V, at constant source-drain voltage, 2 V. In case of Si3N4 top gate the modulation of source-drain current was not significant for the comparable electric field strength. Based on the value of gate voltage for current minima in transfer function the poor quality of Si3N4 -graphene interface is concluded.

  15. Microwave Spectroscopy of Carbon Nanotube Field Effect Transistor

    Directory of Open Access Journals (Sweden)

    Mina A. N.

    2010-10-01

    Full Text Available The quantum transport property of a carbon nanotube field effect transistor (CNTFET is investigated under the effect of microwave radiation and magnetic field. The photon-assisted tunneling probability is deduced by solving Dirac equation. Then the current is deduced according to Landauer-Buttiker formula. Oscillatory behavior of the current is observed which is due to the Coulomb blockade oscillations. It was found, also, that the peak heights of the dependence of the current on the parameters under study are strongly affected by the interplay between the tunneled electrons and the photon energy. This interplay affects on the sidebands resonance. The results obtained in the present paper are found to be in concordant with those in the literature, which confirms the correctness of the proposed model. This study is valuable for nanotechnology applications, e.g., photo-detector devices and solid state quantum computing systems and quantum information processes.

  16. The fundamental downscaling limit of field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Mamaluy, Denis, E-mail: mamaluy@sandia.gov; Gao, Xujiao [Sandia National Laboratories, Albuquerque, New Mexico 87185-1322 (United States)

    2015-05-11

    We predict that within next 15 years a fundamental down-scaling limit for CMOS technology and other Field-Effect Transistors (FETs) will be reached. Specifically, we show that at room temperatures all FETs, irrespective of their channel material, will start experiencing unacceptable level of thermally induced errors around 5-nm gate lengths. These findings were confirmed by performing quantum mechanical transport simulations for a variety of 6-, 5-, and 4-nm gate length Si devices, optimized to satisfy high-performance logic specifications by ITRS. Different channel materials and wafer/channel orientations have also been studied; it is found that altering channel-source-drain materials achieves only insignificant increase in switching energy, which overall cannot sufficiently delay the approaching downscaling limit. Alternative possibilities are discussed to continue the increase of logic element densities for room temperature operation below the said limit.

  17. Tin - an unlikely ally for silicon field effect transistors?

    KAUST Repository

    Hussain, Aftab M.

    2014-01-13

    We explore the effectiveness of tin (Sn), by alloying it with silicon, to use SiSn as a channel material to extend the performance of silicon based complementary metal oxide semiconductors. Our density functional theory based simulation shows that incorporation of tin reduces the band gap of Si(Sn). We fabricated our device with SiSn channel material using a low cost and scalable thermal diffusion process of tin into silicon. Our high-κ/metal gate based multi-gate-field-effect-transistors using SiSn as channel material show performance enhancement, which is in accordance with the theoretical analysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Conductance Oscillations in Spin Field-Effect Transistors

    Institute of Scientific and Technical Information of China (English)

    JIANG Kai-Ming; ZHENG Zhi-Ming; XING Ding-Yu

    2006-01-01

    Ballistic spin transport in spin field-effect transistors is studied by taking into account the Rashba spinorbit coupling, interfacial scattering, and band mismatch. It is shown that the spin conductance oscillation with the semiconductor channel length is a superimposition of the Rashba spin precession and spin interference oscillations. They have different oscillation periods π/kR and π/k with kR the Rashba wavevector and k the Fermi wavevector of the semiconductor channel, and play different parts of slow and rapid oscillations, depending upon the relative magnitude of π/kR and π/k. Only at k = kR does the spin conductance exhibit oscillations of a single period. Two types of different behaviors of the tunnelling magnetoresistance are discussed.

  19. Detection of sulfur dioxide gas with graphene field effect transistor

    Science.gov (United States)

    Ren, Yujie; Zhu, Chaofu; Cai, Weiwei; Li, Huifeng; Ji, Hengxing; Kholmanov, Iskandar; Wu, Yaping; Piner, Richard D.; Ruoff, Rodney S.

    2012-04-01

    Graphene grown by chemical vapor deposition on a Cu foil and transferred onto a Si wafer has been used to fabricate a field effect transistor device that was used to study the sensing of SO2 gas. It was found by in-situ measurements that the SO2 strongly p-dopes the graphene and dramatically shifts its Dirac point. This effect was used to monitor the SO2 gas. The detector can be completely reset by thermal annealing at 100 °C in high vacuum. The response and recovery of the detector are faster at higher temperatures. Moreover, the sensitivity of the SO2 graphene detector increases proportionally with increasing temperature.

  20. Abnormal Dirac point shift in graphene field-effect transistors

    Science.gov (United States)

    Wang, Shaoqing; Jin, Zhi; Huang, Xinnan; Peng, Songang; Zhang, Dayong; Shi, Jingyuan

    2016-09-01

    The shift of Dirac point in graphene devices is of great importance, influencing the reliability and stability. Previous studies show the Dirac point shifts slightly to be more positive when the drain bias increases. Here, an abnormal shift of Dirac point is observed in monolayer graphene field effect transistors by investigating the transfer curves under various drain biases. The voltage of Dirac point shifts positively at first and then decreases rapidly when the channel electric field exceeds some threshold. The negative Dirac point shift is attributed to holes injection into oxide layer and captured by the oxide traps under high channel electric field. This can also be demonstrated through a simple probability model and the graphene Raman spectra before and after the DC measurement.

  1. Field-Effect Tunneling Transistor Based on Vertical Graphene Heterostructures

    Science.gov (United States)

    Britnell, L.; Gorbachev, R. V.; Jalil, R.; Belle, B. D.; Schedin, F.; Mishchenko, A.; Georgiou, T.; Katsnelson, M. I.; Eaves, L.; Morozov, S. V.; Peres, N. M. R.; Leist, J.; Geim, A. K.; Novoselov, K. S.; Ponomarenko, L. A.

    2012-02-01

    An obstacle to the use of graphene as an alternative to silicon electronics has been the absence of an energy gap between its conduction and valence bands, which makes it difficult to achieve low power dissipation in the OFF state. We report a bipolar field-effect transistor that exploits the low density of states in graphene and its one-atomic-layer thickness. Our prototype devices are graphene heterostructures with atomically thin boron nitride or molybdenum disulfide acting as a vertical transport barrier. They exhibit room-temperature switching ratios of ≈50 and ≈10,000, respectively. Such devices have potential for high-frequency operation and large-scale integration.

  2. Recent Trends in Field-Effect Transistors-Based Immunosensors

    Directory of Open Access Journals (Sweden)

    Ana Carolina Mazarin de Moraes

    2016-10-01

    Full Text Available Immunosensors are analytical platforms that detect specific antigen-antibody interactions and play an important role in a wide range of applications in biomedical clinical diagnosis, food safety, and monitoring contaminants in the environment. Field-effect transistors (FET immunosensors have been developed as promising alternatives to conventional immunoassays, which require complicated processes and long-time data acquisition. The electrical signal of FET-based immunosensors is generated as a result of the antigen-antibody conjugation. FET biosensors present real-time and rapid response, require small sample volume, and exhibit higher sensitivity and selectivity. This review brings an overview on the recent literature of FET-based immunosensors, highlighting a diversity of nanomaterials modified with specific receptors as immunosensing platforms for the ultrasensitive detection of various biomolecules.

  3. A tunable colloidal quantum dot photo field-effect transistor

    KAUST Repository

    Ghosh, Subir

    2011-01-01

    We fabricate and investigate field-effect transistors in which a light-absorbing photogate modulates the flow of current along the channel. The photogate consists of colloidal quantum dots that efficiently transfer photoelectrons to the channel across a charge-separating (type-II) heterointerface, producing a primary and sustained secondary flow that is terminated via electron back-recombination across the interface. We explore colloidal quantum dot sizes corresponding to bandgaps ranging from 730 to 1475 nm and also investigate various stoichiometries of aluminum-doped ZnO (AZO) channel materials. We investigate the role of trap state energies in both the colloidal quantum dot energy film and the AZO channel. © 2011 American Institute of Physics.

  4. Improving the radiation hardness of graphene field effect transistors

    Science.gov (United States)

    Alexandrou, Konstantinos; Masurkar, Amrita; Edrees, Hassan; Wishart, James F.; Hao, Yufeng; Petrone, Nicholas; Hone, James; Kymissis, Ioannis

    2016-10-01

    Ionizing radiation poses a significant challenge to the operation and reliability of conventional silicon-based devices. Here, we report the effects of gamma radiation on graphene field-effect transistors (GFETs), along with a method to mitigate those effects by developing a radiation-hardened version of our back-gated GFETs. We demonstrate that activated atmospheric oxygen from the gamma ray interaction with air damages the semiconductor device, and damage to the substrate contributes additional threshold voltage instability. Our radiation-hardened devices, which have protection against these two effects, exhibit minimal performance degradation, improved stability, and significantly reduced hysteresis after prolonged gamma radiation exposure. We believe this work provides an insight into graphene's interactions with ionizing radiation that could enable future graphene-based electronic devices to be used for space, military, and other radiation-sensitive applications.

  5. Theoretical study of phosphorene tunneling field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Jiwon; Hobbs, Chris [SEMATECH, 257 Fuller Rd #2200, Albany, New York 12203 (United States)

    2015-02-23

    In this work, device performances of tunneling field effect transistors (TFETs) based on phosphorene are explored via self-consistent atomistic quantum transport simulations. Phosphorene is an ultra-thin two-dimensional (2-D) material with a direct band gap suitable for TFETs applications. Our simulation shows that phosphorene TFETs exhibit subthreshold slope below 60 mV/dec and a wide range of on-current depending on the transport direction due to highly anisotropic band structures of phosphorene. By benchmarking with monolayer MoTe{sub 2} TFETs, we predict that phosphorene TFETs oriented in the small effective mass direction can yield much larger on-current at the same on-current/off-current ratio than monolayer MoTe{sub 2} TFETs. It is also observed that a gate underlap structure is required for scaling down phosphorene TFETs in the small effective mass direction to suppress the source-to-drain direct tunneling leakage current.

  6. Gas Sensors Based on Polymer Field-Effect Transistors

    Science.gov (United States)

    Lv, Aifeng; Pan, Yong; Chi, Lifeng

    2017-01-01

    This review focuses on polymer field-effect transistor (PFET) based gas sensor with polymer as the sensing layer, which interacts with gas analyte and thus induces the change of source-drain current (ΔISD). Dependent on the sensing layer which can be semiconducting polymer, dielectric layer or conducting polymer gate, the PFET sensors can be subdivided into three types. For each type of sensor, we present the molecular structure of sensing polymer, the gas analyte and the sensing performance. Most importantly, we summarize various analyte–polymer interactions, which help to understand the sensing mechanism in the PFET sensors and can provide possible approaches for the sensor fabrication in the future. PMID:28117760

  7. Photosensitive cadmium telluride thin-film field-effect transistors.

    Science.gov (United States)

    Yang, Gwangseok; Kim, Donghwan; Kim, Jihyun

    2016-02-22

    We report on the graphene-seeded growth and fabrication of photosensitive Cadmium telluride (CdTe)/graphene hybrid field-effect transistors (FETs) subjected to a post-growth activation process. CdTe thin films were selectively grown on pre-defined graphene, and their morphological, electrical and optoelectronic properties were systemically analyzed before and after the CdCl2 activation process. CdCl2-activated CdTe FETs showed p-type behavior with improved electrical features, including higher electrical conductivity (reduced sheet resistance from 1.09 × 10(9) to 5.55 × 10(7) Ω/sq.), higher mobility (from 0.025 to 0.20 cm2/(V·s)), and faster rise time (from 1.23 to 0.43 s). A post-growth activation process is essential to fabricate high-performance photosensitive CdTe/graphene hybrid devices.

  8. Gas Sensors Based on Polymer Field-Effect Transistors.

    Science.gov (United States)

    Lv, Aifeng; Pan, Yong; Chi, Lifeng

    2017-01-22

    This review focuses on polymer field-effect transistor (PFET) based gas sensor with polymer as the sensing layer, which interacts with gas analyte and thus induces the change of source-drain current (ΔISD). Dependent on the sensing layer which can be semiconducting polymer, dielectric layer or conducting polymer gate, the PFET sensors can be subdivided into three types. For each type of sensor, we present the molecular structure of sensing polymer, the gas analyte and the sensing performance. Most importantly, we summarize various analyte-polymer interactions, which help to understand the sensing mechanism in the PFET sensors and can provide possible approaches for the sensor fabrication in the future.

  9. GaN Metal Oxide Semiconductor Field Effect Transistors

    Energy Technology Data Exchange (ETDEWEB)

    Ren, F.; Pearton, S.J.; Abernathy, C.R.; Baca, A.; Cheng, P.; Shul, R.J.; Chu, S.N.G.; Hong, M.; Lothian, J.R.; Schurman, M.J.

    1999-03-02

    A GaN based depletion mode metal oxide semiconductor field effect transistor (MOSFET) was demonstrated using Ga{sub 2}O{sub 3}(Gd{sub 2}O{sub 3}) as the gate dielectric. The MOS gate reverse breakdown voltage was > 35V which was significantly improved from 17V of Pt Schottky gate on the same material. A maximum extrinsic transconductance of 15 mS/mm was obtained at V{sub ds} = 30 V and device performance was limited by the contact resistance. A unity current gain cut-off frequency, f{sub {tau}}, and maximum frequency of oscillation, f{sub max} of 3.1 and 10.3 GHz, respectively, were measured at V{sub ds} = 25 V and V{sub gs} = {minus}20 V.

  10. Silicon junctionless field effect transistors as room temperature terahertz detectors

    Energy Technology Data Exchange (ETDEWEB)

    Marczewski, J., E-mail: jmarcz@ite.waw.pl; Tomaszewski, D.; Zaborowski, M. [Institute of Electron Technology, al. Lotnikow 32/46, 02-668 Warsaw (Poland); Knap, W. [Institute of High Pressure Physics of the Polish Academy of Sciences, ul. Sokolowska 29/37, 01-142 Warsaw (Poland); Laboratory Charles Coulomb, Montpellier University & CNRS, Place E. Bataillon, Montpellier 34095 (France); Zagrajek, P. [Institute of Optoelectronics, Military University of Technology, ul. gen. S. Kaliskiego 2, 00-908 Warsaw (Poland)

    2015-09-14

    Terahertz (THz) radiation detection by junctionless metal-oxide-semiconductor field-effect transistors (JL MOSFETs) was studied and compared with THz detection using conventional MOSFETs. It has been shown that in contrast to the behavior of standard transistors, the junctionless devices have a significant responsivity also in the open channel (low resistance) state. The responsivity for a photolithographically defined JL FET was 70 V/W and the noise equivalent power 460 pW/√Hz. Working in the open channel state may be advantageous for THz wireless and imaging applications because of its low thermal noise and possible high operating speed or large bandwidth. It has been proven that the junctionless MOSFETs can also operate in a zero gate bias mode, which enables simplification of the THz array circuitry. Existing models of THz detection by MOSFETs were considered and it has been demonstrated that the process of detection by these junctionless devices cannot be explained within the framework of the commonly accepted models and therefore requires a new theoretical approach.

  11. Compact model for switching characteristics of graphene field effect transistor

    Science.gov (United States)

    Sreenath, R.; Bala Tripura Sundari, B.

    2016-04-01

    The scaling of CMOS transistors has resulted in intensified short channel effects, indicating that CMOS has reached its physical limits. Alternate non silicon based materials namely carbon based graphene, carbon nanotubes are being explored for usability as channel and interconnect material due to their established higher mobility and robustness. This paper presents a drift-diffusion based circuit simulatable Verilog-A compact model of graphene field effect transistor (GFET) for channel length of 100nm.The focus is on the development of simulatable device model in Verilog A based on intrinsic parameters and obtain the current, high cutoff frequency and use the model into circuit level simulations to realize an inverter and a 3-stage ring oscillator using Synopsys HSPICE. The applications are so chosen that their switching characteristics enable the determination of the RF frequency ranges of operation that the model can achieve when used in digital applications and also to compare its performance with existing CMOS model. The GFET's switching characteristics and power consumption were found to be better than similarly sized CMOS operating at same range of voltages. The basic frequency of operation in the circuit is of significant importance so as to use the model in other applications at RF and in future for millimeter wave applications. The frequency of operation at circuit level is found to be 1.1GHz at 100nm which is far higher than the existing frequency of 245 MHz reported at 500nm using AlN.

  12. Cylindrical Field Effect Transistor: A Full Volume Inversion Device

    KAUST Repository

    Fahad, Hossain M.

    2010-12-01

    The increasing demand for high performance as well as low standby power devices has been the main reason for the aggressive scaling of conventional CMOS transistors. Current devices are at the 32nm technology node. However, due to physical limitations as well as increase in short-channel effects, leakage, power dissipation, this scaling trend cannot continue and will eventually hit a barrier. In order to overcome this, alternate device topologies have to be considered altogether. Extensive research on ultra thin body double gate FETs and gate all around nanowire FETs has shown a lot of promise. Under strong inversion, these devices have demonstrated increased performance over their bulk counterparts. This is mainly attributed to full carrier inversion in the body. However, these devices are still limited by lithographic and processing challenges making them unsuitable for commercial production. This thesis explores a unique device structure called the CFET (Cylindrical Field Effect Transistors) which also like the above, relies on complete inversion of carriers in the body/bulk. Using dual gates; an outer and an inner gate, full-volume inversion is possible with benefits such as enhanced drive currents, high Ion/Ioff ratios and reduced short channel effects.

  13. Nano-textured high sensitivity ion sensitive field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Hajmirzaheydarali, M.; Sadeghipari, M.; Akbari, M.; Shahsafi, A.; Mohajerzadeh, S., E-mail: mohajer@ut.ac.ir [Thin Film and Nanoelectronics Lab, Nanoelectronics Center of Excellence, School of Electrical and Computer Engineering, University of Tehran, Tehran 143957131 (Iran, Islamic Republic of)

    2016-02-07

    Nano-textured gate engineered ion sensitive field effect transistors (ISFETs), suitable for high sensitivity pH sensors, have been realized. Utilizing a mask-less deep reactive ion etching results in ultra-fine poly-Si features on the gate of ISFET devices where spacing of the order of 10 nm and less is achieved. Incorporation of these nano-sized features on the gate is responsible for high sensitivities up to 400 mV/pH in contrast to conventional planar structures. The fabrication process for this transistor is inexpensive, and it is fully compatible with standard complementary metal oxide semiconductor fabrication procedure. A theoretical modeling has also been presented to predict the extension of the diffuse layer into the electrolyte solution for highly featured structures and to correlate this extension with the high sensitivity of the device. The observed ultra-fine features by means of scanning electron microscopy and transmission electron microscopy tools corroborate the theoretical prediction.

  14. Slowing DNA Translocation in a Nanofluidic Field-Effect Transistor.

    Science.gov (United States)

    Liu, Yifan; Yobas, Levent

    2016-04-26

    Here, we present an experimental demonstration of slowing DNA translocation across a nanochannel by modulating the channel surface charge through an externally applied gate bias. The experiments were performed on a nanofluidic field-effect transistor, which is a monolithic integrated platform featuring a 50 nm-diameter in-plane alumina nanocapillary whose entire length is surrounded by a gate electrode. The field-effect transistor behavior was validated on the gating of ionic conductance and protein transport. The gating of DNA translocation was subsequently studied by measuring discrete current dips associated with single λ-DNA translocation events under a source-to-drain bias of 1 V. The translocation speeds under various gate bias conditions were extracted by fitting event histograms of the measured translocation time to the first passage time distributions obtained from a simple 1D biased diffusion model. A positive gate bias was observed to slow the translocation of single λ-DNA chains markedly; the translocation speed was reduced by an order of magnitude from 18.4 mm/s obtained under a floating gate down to 1.33 mm/s under a positive gate bias of 9 V. Therefore, a dynamic and flexible regulation of the DNA translocation speed, which is vital for single-molecule sequencing, can be achieved on this device by simply tuning the gate bias. The device is realized in a conventional semiconductor microfabrication process without the requirement of advanced lithography, and can be potentially further developed into a compact electronic single-molecule sequencer.

  15. Silicon Nanomembrane Bipolar Junction Transistors for Microwave Frequency Applications

    Science.gov (United States)

    Bavier, John; Ballarotto, Vince; Cumings, John

    2014-03-01

    Silicon nanomembranes (SiNMs) are a promising material for flexible semiconductor devices due to their high carrier mobility and compatibility with standard CMOS processing. Previous studies have reported SiNM field-effect transistors with operating frequencies as high as 12 GHz. In order to expand the utility of SiNM devices, a method for the fabrication of monocrystalline microwave frequency silicon bipolar junction transistors (BJTs) will be presented. High-temperature processing of SiNM BJT devices is performed on a Silicon-on-Insulator (SOI) wafer. Using angled ion implantation, conformal chemical vapor deposition and anisotropic reactive ion etching, a poly-silicon sidewall spacer is formed. This spacer defines a base region approximately 200nm wide without the use of electron beam lithography. Devices are then released using selective wet etching in HF and transferred to alternate flexible substrates. Microwave frequency data will be presented, and the effects of the transfer process on device performance will be discussed.

  16. Gas Sensors Based on Semiconducting Nanowire Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Ping Feng

    2014-09-01

    Full Text Available One-dimensional semiconductor nanostructures are unique sensing materials for the fabrication of gas sensors. In this article, gas sensors based on semiconducting nanowire field-effect transistors (FETs are comprehensively reviewed. Individual nanowires or nanowire network films are usually used as the active detecting channels. In these sensors, a third electrode, which serves as the gate, is used to tune the carrier concentration of the nanowires to realize better sensing performance, including sensitivity, selectivity and response time, etc. The FET parameters can be modulated by the presence of the target gases and their change relate closely to the type and concentration of the gas molecules. In addition, extra controls such as metal decoration, local heating and light irradiation can be combined with the gate electrode to tune the nanowire channel and realize more effective gas sensing. With the help of micro-fabrication techniques, these sensors can be integrated into smart systems. Finally, some challenges for the future investigation and application of nanowire field-effect gas sensors are discussed.

  17. Plasmonic response of partially gated field effect transistors

    Science.gov (United States)

    Rudin, S.; Rupper, G.; Reed, M. L.; Shur, M.

    2016-09-01

    Electron density oscillations in the transistor channels - plasma waves in the two-dimensional electron gas - determine the high frequency device response. Plasmonic field effect transistors have emerged as very sensitive, tunable, and extremely fast detectors of THz radiation. They have been implemented using silicon (CMOS), AlGaAs/InGaAs HEMTs, and AlGaAs/InGaAs HEMTs, with the HEMTs shown to operate more efficiently at higher THz frequencies. These HEMTs have both gated and ungated sections of the device channel between the source and drain, and the photovoltaic regime of operation requires an asymmetric gate placement in the device channel. The interactions of the plasma waves in the gated and ungated channel regions strongly affect the overall response and have been investigated in numerous publications. This work addresses a new aspect of such interaction - the effect of the relative position of the gated and ungated section. We show this previously unexplored effect plays a dominant role in determining the response. The results of the numerical simulation based on the solution of the complete system of the hydrodynamic equations describing the electron fluid in the device channel show that the inverse response frequency could be approximated by the sum of the gated plasmon transit time in the gated section of the device, the ungated plasmon transit time in the ungated section of the device between the gate and the drain, and the RC gate-to-source constant. Here R and C are the resistance and capacitance of the gate to source section. Hence, the highest speed is achieved when the gate is as close to the source as possible. This suggests a novel plasmonic detector design, where the gate and source electrode overlap, which is shown to have a superior frequency response for the same distance between the source and the drain.

  18. Nanowire Tunnel Field Effect Transistors: Prospects and Pitfalls

    Science.gov (United States)

    Sylvia, Somaia Sarwat

    The tunnel field effect transistor (TFET) has the potential to operate at lower voltages and lower power than the field effect transistor (FET). The TFET can circumvent the fundamental thermal limit of the inverse subthreshold slope (S) by exploiting interband tunneling of non-equilibrium "cold" carriers. The conduction mechanism in the TFET is governed by band-to-band tunneling which limits the drive current. TFETs built with III-V materials like InAs and InSb can produce enough tunneling current because of their small direct bandgap. Our simulation results show that although they require highly degenerate source doping to support the high electric fields in the tunnel region, the devices achieve minimum inverse subthreshold slopes of 30 mV/dec. In subthreshold, these devices experience both regimes of voltage-controlled tunneling and cold-carrier injection. Numerical results based on a discretized 8-band k.p model are compared to analytical WKB theory. For both regular FETs and TFETs, direct channel tunneling dominates the leakage current when the physical gate length is reduced to 5 nm. Therefore, a survey of materials is performed to determine their ability to suppress the direct tunnel current through a 5 nm barrier. The tunneling effective mass gives the best indication of the relative size of the tunnel currents. Si gives the lowest overall tunnel current for both the conduction and valence band and, therefore, it is the optimum choice for suppressing tunnel current at the 5 nm scale. Our numerical simulation shows that the finite number, random placement, and discrete nature of the dopants in the source of an InAs nanowire (NW) TFET affect both the mean value and the variance of the drive current and the inverse subthreshold slope. The discrete doping model gives an average drive current and an inverse subthreshold slope that are less than those predicted from the homogeneous doping model. The doping density required to achieve a target drive current is

  19. A silicon carbide nanowire field effect transistor for DNA detection.

    Science.gov (United States)

    Fradetal, L; Bano, E; Attolini, G; Rossi, F; Stambouli, V

    2016-06-10

    This work reports on the label-free electrical detection of DNA molecules for the first time, using silicon carbide (SiC) as a novel material for the realization of nanowire field effect transistors (NWFETs). SiC is a promising semiconductor for this application due to its specific characteristics such as chemical inertness and biocompatibility. Non-intentionally n-doped SiC NWs are first grown using a bottom-up vapor-liquid-solid (VLS) mechanism, leading to the NWs exhibiting needle-shaped morphology, with a length of approximately 2 μm and a diameter ranging from 25 to 60 nm. Then, the SiC NWFETs are fabricated and functionalized with DNA molecule probes via covalent coupling using an amino-terminated organosilane. The drain current versus drain voltage (I d-V d) characteristics obtained after the DNA grafting and hybridization are reported from the comparative and simultaneous measurements carried out on the SiC NWFETs, used either as sensors or references. As a representative result, the current of the sensor is lowered by 22% after probe DNA grafting and by 7% after target DNA hybridization, while the current of the reference does not vary by more than ±0.6%. The current decrease confirms the field effect induced by the negative charges of the DNA molecules. Moreover, the selectivity, reproducibility, reversibility and stability of the studied devices are emphasized by de-hybridization, non-complementary hybridization and re-hybridization experiments. This first proof of concept opens the way for future developments using SiC-NW-based sensors.

  20. Boron doped simulated graphene field effect transistor model

    Science.gov (United States)

    Sharma, Preetika; Kaur, Inderpreet; Gupta, Shuchi; Singh, Sukhbir

    2016-05-01

    Graphene based electronic devices due to its unique properties has transformed electronics. A Graphene Field Effect Transistor (GNRFET) model is simulated in Virtual Nano Lab (VNL) and the calculations are based on density functional theory (DFT). Simulations were performed on this pristine GNRFET model and the transmission spectrum was observed. The graph obtained showed a uniform energy gap of +1 to -1eV and the highest transmission peak at -1.75 eV. To this pristine model of GNRFET, doping was introduced and its effect was seen on the Fermi level obtained in the transmission spectrum. Boron as a dopant was used which showed variations in both the transmission peaks and the energy gap. In this model, first the single boron was substituted in place of carbon and Fermi level showed an energy gap of 1.5 to -0.5eV with the highest transmission peak at -1.3 eV. In another variation in the model, two carbon atoms were replaced by two boron atoms and Fermi level shifted from 2 to 0.25eV. In this observation, the highest transmission peak was observed at -1(approx.). The use of nanoelectronic devices have opened many areas of applications as GFET is an excellent building block for electronic circuits, and is being used in applications such as high-performance frequency doublers and mixers, digital modulators, phase detectors, optoelectronics and spintronics.

  1. Ambipolar organic field-effect transistors on unconventional substrates

    Science.gov (United States)

    Cosseddu, P.; Mattana, G.; Orgiu, E.; Bonfiglio, A.

    2009-04-01

    In this paper we report on the realization of flexible all-organic ambipolar field-effect transistors (FETs) realized on unconventional substrates, such as plastic films and textile yarns. A double layer pentacene-C60 heterojunction was used as the semiconductor layer. The contacts were made with poly(ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT:PSS) and patterned by means of soft lithography microcontact printing (μCP). Very interestingly growing C60 on a predeposited pentacene buffer layer leads to a clear improvement in the morphology and crystallinity of the film so it obtains n-type conduction despite the very high electron injection barrier at the interface between PEDOT:PSS and C60. As a result, it was possible to obtain all-organic ambipolar FETs and to optimize their electrical properties by tuning the thicknesses of the two employed active layers. Moreover, it will be shown that modifying the triple interface between dielectric/semiconductor/electrodes is a crucial point for optimizing and balancing injection and transport of both kinds of charge carriers. In particular, we demonstrate that using a middle contact configuration in which source and drain electrodes are sandwiched between pentacene and C60 layers allows significantly improving the electrical performance in planar ambipolar devices. These findings are very important because they pave the way for the realization of low-cost, fully flexible and stretchable organic complementary circuits for smart wearable and textile electronics applications.

  2. Graphene field-effect transistor application for flow sensing

    Directory of Open Access Journals (Sweden)

    Łuszczek Maciej

    2017-01-01

    Full Text Available Microflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall flow sensor performance. In this work we propose graphene field-effect transistor (GFET to be used as microflow sensor. Temperature distribution in graphene channel was simulated and the analysis of heat convection was performed to establish the relation between the fluidic flow velocity and the temperature gradient. It was shown that the negative temperature coefficient (NTC of graphene could enable the self-protection of the device and should minimize sensing error from currentinduced heating. It was also argued that the planar design of the GFET sensor makes it suitable for the real application due to supposed mechanical stability of such a construction.

  3. Graphene field-effect transistor application for flow sensing

    Science.gov (United States)

    Łuszczek, Maciej; Świsulski, Dariusz; Hanus, Robert; Zych, Marcin; Petryka, Leszek

    Microflow sensors offer great potential for applications in microfluidics and lab-on-a-chip systems. However, thermal-based sensors, which are commonly used in modern flow sensing technology, are mainly made of materials with positive temperature coefficients (PTC) and suffer from a self-heating effect and slow response time. Therefore, the design of novel devices and careful selection of materials are required to improve the overall flow sensor performance. In this work we propose graphene field-effect transistor (GFET) to be used as microflow sensor. Temperature distribution in graphene channel was simulated and the analysis of heat convection was performed to establish the relation between the fluidic flow velocity and the temperature gradient. It was shown that the negative temperature coefficient (NTC) of graphene could enable the self-protection of the device and should minimize sensing error from currentinduced heating. It was also argued that the planar design of the GFET sensor makes it suitable for the real application due to supposed mechanical stability of such a construction.

  4. Fabrication of SWCNT-Graphene Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Shuangxi Xie

    2015-09-01

    Full Text Available Graphene and single-walled carbon nanotube (SWCNT have been widely studied because of their extraordinary electrical, thermal, mechanical, and optical properties. This paper describes a novel and flexible method to fabricate all-carbon field-effect transistors (FETs. The fabrication process begins with assembling graphene grown by chemical vapor deposition (CVD on a silicon chip with SiO2 as the dielectric layer and n-doped Si substrate as the gate. Next, an atomic force microscopy (AFM-based mechanical cutting method is utilized to cut the graphene into interdigitated electrodes with nanogaps, which serve as the source and drain. Lastly, SWCNTs are assembled on the graphene interdigitated electrodes by dielectrophoresis to form the conductive channel. The electrical properties of the thus-fabricated SWCNT-graphene FETs are investigated and their FET behavior is confirmed. The current method effectively integrates SWCNTs and graphene in nanoelectronic devices, and presents a new method to build all-carbon electronic devices.

  5. Demonstration of Complementary Ternary Graphene Field-Effect Transistors

    Science.gov (United States)

    Kim, Yun Ji; Kim, So-Young; Noh, Jinwoo; Shim, Chang Hoo; Jung, Ukjin; Lee, Sang Kyung; Chang, Kyoung Eun; Cho, Chunhum; Lee, Byoung Hun

    2016-12-01

    Strong demand for power reduction in state-of-the-art semiconductor devices calls for novel devices and architectures. Since ternary logic architecture can perform the same function as binary logic architecture with a much lower device density and higher information density, a switch device suitable for the ternary logic has been pursued for several decades. However, a single device that satisfies all the requirements for ternary logic architecture has not been demonstrated. We demonstrated a ternary graphene field-effect transistor (TGFET), showing three discrete current states in one device. The ternary function was achieved by introducing a metal strip to the middle of graphene channel, which created an N-P-N or P-N-P doping pattern depending on the work function of the metal. In addition, a standard ternary inverter working at room temperature has been achieved by modulating the work function of the metal in a graphene channel. The feasibility of a ternary inverter indicates that a general ternary logic architecture can be realized using complementary TGFETs. This breakthrough will provide a key stepping-stone for an extreme-low-power computing technology.

  6. Operational stability of organic field-effect transistors.

    Science.gov (United States)

    Bobbert, Peter A; Sharma, Abhinav; Mathijssen, Simon G J; Kemerink, Martijn; de Leeuw, Dago M

    2012-03-02

    Organic field-effect transistors (OFETs) are considered in technological applications for which low cost or mechanical flexibility are crucial factors. The environmental stability of the organic semiconductors used in OFETs has improved to a level that is now sufficient for commercialization. However, serious problems remain with the stability of OFETs under operation. The causes for this have remained elusive for many years. Surface potentiometry together with theoretical modeling provide new insights into the mechanisms limiting the operational stability. These indicate that redox reactions involving water are involved in an exchange of mobile charges in the semiconductor with protons in the gate dielectric. This mechanism elucidates the established key role of water and leads in a natural way to a universal "stress function", describing the stretched exponential-like time dependence ubiquitously observed. Further study is needed to determine the generality of the mechanism and the role of other mechanisms. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Field-effect transistor chemical sensors of single nanoribbon of copper phthalocyanine

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Copper phthalocyanine (CuPc) nanoribbon field-effect transistors were implemented as chemical sensors. They showed fast response and high reversibility in the detection of the tetrahydrofuran atmosphere at room temperature. The drain current of the field-effect transistor sensor decreased from 6.7 to 0.2 nA when the transistor was measured under the tetrahydrofuran atmosphere. The sensor was self-refreshable in a few minutes. These results demonstrate that the organic single crystalline nanoribbon transistors could effectively act as chemical sensors.

  8. Toward Complementary Ionic Circuits: The npn Ion Bipolar Junction Transistor

    OpenAIRE

    Tybrandt, Klas; Gabrielsson, Erik; Berggren, Magnus

    2011-01-01

    Many biomolecules are charged and may therefore be transported with ionic currents. As a step toward addressable ionic delivery circuits, we report on the development of a npn ion bipolar junction transistor (npn-IBJT) as an active control element of anionic currents in general, and specifically, demonstrate actively modulated delivery of the neurotransmitter glutamic acid. The functional materials of this transistor are ion exchange layers and conjugated polymers. The npn-IBJT shows stable t...

  9. Toward complementary ionic circuits: the npn ion bipolar junction transistor.

    Science.gov (United States)

    Tybrandt, Klas; Gabrielsson, Erik O; Berggren, Magnus

    2011-07-06

    Many biomolecules are charged and may therefore be transported with ionic currents. As a step toward addressable ionic delivery circuits, we report on the development of a npn ion bipolar junction transistor (npn-IBJT) as an active control element of anionic currents in general, and specifically, demonstrate actively modulated delivery of the neurotransmitter glutamic acid. The functional materials of this transistor are ion exchange layers and conjugated polymers. The npn-IBJT shows stable transistor characteristics over extensive time of operation and ion current switch times below 10 s. Our results promise complementary chemical circuits similar to the electronic equivalence, which has proven invaluable in conventional electronic applications.

  10. CHEMICALLY MODIFIED FIELD-EFFECT TRANSISTORS - POTENTIOMETRIC AG+ SELECTIVITY OF PVC MEMBRANES BASED ON MACROCYCLIC THIOETHERS

    NARCIS (Netherlands)

    BRZOZKA, Z; COBBEN, PLHM; REINHOUDT, DN; EDEMA, JJH; KELLOGG, RM

    1993-01-01

    A chemically modified field-effect transistor (CHEMFET) with satisfactory Ag+ selectivity is described. The potentiometric Ag+ selectivities of CHEMFETs with plasticized PVC membranes based on macrocyclic thioethers have been determined. All the macrocyclic thioethers tested showed silver response a

  11. Low Temperature Noise and Electrical Characterization of the Company Heterojunction Field-Effect Transistor

    Science.gov (United States)

    Cunningham, Thomas J.; Gee, Russell C.; Fossum, Eric R.; Baier, Steven M.

    1993-01-01

    This paper discusses the electrical properties of the complementary heterojunction field-effect transistor (CHFET) at 4K, including the gate leakage current, the subthreshold transconductance, and the input-referred noise voltage.

  12. China's first ZnO nanorod field-effect transistor developed at CAS

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    @@ Recently, an zinc oxide (ZnO) nanorod field-effect transistor (FET), the first of its kind as a nano-device in China,was successfully fabricated by scientists with the CAS Institute of Microelectronics (IME).

  13. Dynamics of threshold voltage shifts in organic and amorphous silicon field-effect transistors

    NARCIS (Netherlands)

    Mathijssen, Simon G. J.; Colle, Michael; Gomes, Henrique; Smits, Edsger C. P.; de Boer, Bert; McCulloch, Iain; Bobbert, Peter A.; de Leeuw, Dago M.; Cölle, Michael

    2007-01-01

    The electrical instability of organic field-effect transistors is investigated. We observe that the threshold-voltage shift (see figure) shows a stretched-exponential time dependence under an applied gate bias. The activation energy of 0.6 eV is common for our and all other organic transistors repor

  14. Electrolyte-gated organic field-effect transistor for selective reversible ion detection.

    Science.gov (United States)

    Schmoltner, Kerstin; Kofler, Johannes; Klug, Andreas; List-Kratochvil, Emil J W

    2013-12-17

    An ion-sensitive electrolyte-gated organic field-effect transistor for selective and reversible detection of sodium (Na(+) ) down to 10(-6) M is presented. The inherent low voltage - high current operation of these transistors in combination with a state-of-the-art ion-selective membrane proves to be a novel, versatile modular sensor platform.

  15. Environmental Effects on Hysteresis of Transfer Characteristics in Molybdenum Disulfide Field-Effect Transistors

    OpenAIRE

    Yoshihiro Shimazu; Mitsuki Tashiro; Satoshi Sonobe; Masaki Takahashi

    2016-01-01

    Molybdenum disulfide (MoS2) has recently received much attention for nanoscale electronic and photonic applications. To explore the intrinsic properties and enhance the performance of MoS2-based field-effect transistors, thorough understanding of extrinsic effects such as environmental gas and contact resistance of the electrodes is required. Here, we report the effects of environmental gases on the transport properties of back-gated multilayered MoS2 field-effect transistors. Comparisons bet...

  16. Emitter space charge layer transit time in bipolar junction transistors

    Science.gov (United States)

    Rustagi, S. C.; Chattopadhyaya, S. K.

    1981-04-01

    The charge defined emitter space charge layer transit times of double diffused transistors have been calculated using a regional approach, and compared with the corresponding base transit times. The results obtained for emitter space-charge layer transit times have been discussed with reference to the capacitance analysis of Morgan and Smit (1960) for graded p-n junctions.

  17. Organic light emitting field effect transistors based on an ambipolar p-i-n layered structure

    Science.gov (United States)

    Maiorano, V.; Bramanti, A.; Carallo, S.; Cingolani, R.; Gigli, G.

    2010-03-01

    A bottom contact/top gate ambipolar "p-i-n" layered light emitting field effect transistor with the active medium inserted between two doped transport layers, is reported. The doping profile results crucial to the capability of emitting light, as well as to the electrical characteristics of the device. In this sense, high output current at relative low applied gate/drain voltage and light emission along the whole large area transistor channel are observed, putting the basis to full integration of organic light emitting field effect transistors in planar complex devices.

  18. Single-crystal organic field-effect transistors based on dibenzo-tetrathiafulvalene

    NARCIS (Netherlands)

    Mas-Torrent, M.; Hadley, P.; Bromley, S.T.; Crivillers, N.; Veciana, J.; Rovira, C.

    2004-01-01

    We report on the fabrication and characterization of field-effect transistors based on single crystals of the organic semiconductor dibenzo-tetrathiafulvalene (DB-TTF). We demonstrate that it is possible to prepare very-good-quality DB-TTF crystals from solution. These devices show high field-effect

  19. Non-Planar Nanotube and Wavy Architecture Based Ultra-High Performance Field Effect Transistors

    KAUST Repository

    Hanna, Amir

    2016-11-01

    This dissertation presents a unique concept for a device architecture named the nanotube (NT) architecture, which is capable of higher drive current compared to the Gate-All-Around Nanowire architecture when applied to heterostructure Tunnel Field Effect Transistors. Through the use of inner/outer core-shell gates, heterostructure NT TFET leverages physically larger tunneling area thus achieving higher driver current (ION) and saving real estates by eliminating arraying requirement. We discuss the physics of p-type (Silicon/Indium Arsenide) and n-type (Silicon/Germanium hetero-structure) based TFETs. Numerical TCAD simulations have shown that NT TFETs have 5x and 1.6 x higher normalized ION when compared to GAA NW TFET for p and n-type TFETs, respectively. This is due to the availability of larger tunneling junction cross sectional area, and lower Shockley-Reed-Hall recombination, while achieving sub 60 mV/dec performance for more than 5 orders of magnitude of drain current, thus enabling scaling down of Vdd to 0.5 V. This dissertation also introduces a novel thin-film-transistors architecture that is named the Wavy Channel (WC) architecture, which allows for extending device width by integrating vertical fin-like substrate corrugations giving rise to up to 50% larger device width, without occupying extra chip area. The novel architecture shows 2x higher output drive current per unit chip area when compared to conventional planar architecture. The current increase is attributed to both the extra device width and 50% enhancement in field effect mobility due to electrostatic gating effects. Digital circuits are fabricated to demonstrate the potential of integrating WC TFT based circuits. WC inverters have shown 2× the peak-to-peak output voltage for the same input, and ~2× the operation frequency of the planar inverters for the same peak-to-peak output voltage. WC NAND circuits have shown 2× higher peak-to-peak output voltage, and 3× lower high-to-low propagation

  20. Electrostatic fields in hybrid heterojunctions: Field-effect transistor, topological insulator, & thermoelectronic application

    Science.gov (United States)

    Ireland, Robert Matthew

    Organic semiconductors (OSC) are still surging in popularity for sustainable electronic devices, especially since they can perform as well as amorphous and polycrystalline silicon materials. Although OSCs have processing advantages that give rise to novel opportunities compared to inorganic semiconductors (ISCs), devices usually require inorganic materials for highly conductive connections or other functionality. Significantly, OSCs can be used to tune or modify the behavior of inorganic semiconductors (ISCs) by exploiting the junction between two semiconductors (a heterojunction). The possible creation of stable interfaces between ISCs and OSCs provides a practically limitless range of functionalities. Broadly, my goal is to study interfaces between OSCs and ISCs (hybrid heterojunctions) by testing devices of different configurations and altering the internal fields systematically, as well as with the aid of electron- and force-microscopy, and photoelectron spectroscopy. This thesis contains three major sections based around nascent, relevant applications: field-effect transistors, topological insulators, and thermoelectrics. First I study the effects of combining tellurium thin-films with OSC layers in field-effect transistors, where the organic acts both as a substrate modification layer and electrostatic gate. Secondly, I use electron withdrawing OSCs as gating materials for modifying Bi2Se3 in order to realize fundamental topological insulator behavior. Thirdly, I develop polymer-particle composites, including doping of the polymers and stabilization of inorganic particles with an electronic density of states that supports good thermoelectric behavior. We show that OSCs can undeniably be used to significantly modify properties of ISCs, namely tellurium, bismuth selenide, and organometallic compounds. I will first discuss the interfacial fields intrinsic to each heterojunction or device structure. Then I implement an additional electrostatic gate as part of the

  1. Patterning technology for solution-processed organic crystal field-effect transistors

    OpenAIRE

    Yun Li; Huabin Sun; Yi Shi; Kazuhito Tsukagoshi

    2014-01-01

    Organic field-effect transistors (OFETs) are fundamental building blocks for various state-of-the-art electronic devices. Solution-processed organic crystals are appreciable materials for these applications because they facilitate large-scale, low-cost fabrication of devices with high performance. Patterning organic crystal transistors into well-defined geometric features is necessary to develop these crystals into practical semiconductors. This review provides an update on recent development...

  2. Organic thin films as active materials in field effect transistors and electrochemical sensing

    OpenAIRE

    Tarabella, Giuseppe

    2012-01-01

    This PhD thesis is focused on Organic Electronics, an emerging field where different disciplines converge to gain insights into the properties of organic materials and their applications. Under the present work different organic materials have been realized and analysed for application both in Organic Field Effect Transistors and electrochemical sensing with Organic Electrochemical Transistors. An overview about Organic Electronic is reported with the most recent advancement of the last year...

  3. Utilization of a Buffered Dielectric to Achieve High Field-Effect Carrier Mobility in Graphene Transistors

    OpenAIRE

    Farmer, Damon B.; Chiu, Hsin-Ying; Lin, Yu-Ming; Jenkins, Keith A.; Xia, Fengnian; Avouris, Phaedon

    2009-01-01

    We utilize an organic polymer buffer layer between graphene and conventional gate dielectrics in top-gated graphene transistors. Unlike other insulators, this dielectric stack does not significantly degrade carrier mobility, allowing for high field-effect mobilities to be retained in top-gate operation. This is demonstrated in both two-point and four-point analysis, and in the high-frequency operation of a graphene transistor. Temperature dependence of the carrier mobility suggests that phono...

  4. Completely independent electrical control of spin and valley in a silicene field effect transistor.

    Science.gov (United States)

    Zhai, Xuechao; Jin, Guojun

    2016-09-07

    One-atom-thick silicene is a silicon-based hexagonal-lattice material with buckled structure, where an electron fuses multiple degrees of freedom including spin, sublattice pseudospin and valley. We here demonstrate that a valley-selective spin filter (VSSF) that supports single-valley and single-spin transport can be realized in a silicene field effect transistor constructed of an npn junction, where an antiferromagnetic exchange field and a perpendicular electric field are applied in the p-doped region. The nontrivial VSSF property benefits from an electrically controllable state of spin-polarized single-valley Dirac cone. By reversing the electric field direction, the device can operate as a spin-reversed but valley-unreversed filter due to the dependence of band gap on spin and valley. Further, we find that all the possible spin-valley configurations of VSSF can be achieved just by tuning the electric field. Our findings pave the way to the realization of completely independent electrical control of spin and valley in silicene circuits.

  5. Tunnel Field-Effect Transistors in 2D Transition Metal Dichalcogenide Materials

    CERN Document Server

    Ilatikhameneh, Hesameddin; Novakovic, Bozidar; Klimeck, Gerhard; Rahman, Rajib; Appenzeller, Joerg

    2015-01-01

    In this work, the performance of Tunnel Field-Effect Transistors (TFETs) based on two-dimensional Transition Metal Dichalcogenide (TMD) materials is investigated by atomistic quantum transport simulations. One of the major challenges of TFETs is their low ON-currents. 2D material based TFETs can have tight gate control and high electric fields at the tunnel junction, and can in principle generate high ON-currents along with a sub-threshold swing smaller than 60 mV/dec. Our simulations reveal that high performance TMD TFETs, not only require good gate control, but also rely on the choice of the right channel material with optimum band gap, effective mass and source/drain doping level. Unlike previous works, a full band atomistic tight binding method is used self-consistently with 3D Poisson equation to simulate ballistic quantum transport in these devices. The effect of the choice of TMD material on the performance of the device and its transfer characteristics are discussed. Moreover, the criteria for high ON...

  6. Current fluctuation of electron and hole carriers in multilayer WSe{sub 2} field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Seung-Pil; Shin, Jong Mok; Jang, Ho-Kyun; Jin, Jun Eon; Kim, Gyu-Tae, E-mail: gtkim@korea.ac.kr [School of Electrical Engineering, Korea University, Seoul 02481 (Korea, Republic of); Kim, Yong Jin; Kim, Young Keun [Department of Materials Science and Engineering, Korea University, Seoul 02481 (Korea, Republic of); Shin, Minju [School of Electrical Engineering, Korea University, Seoul 02481 (Korea, Republic of); IMEP-LAHC, Grenoble INP-MINATEC, 3 Parvis Louis Neel, 38016 Grenoble (France)

    2015-12-14

    Two-dimensional materials have outstanding scalability due to their structural and electrical properties for the logic devices. Here, we report the current fluctuation in multilayer WSe{sub 2} field effect transistors (FETs). In order to demonstrate the impact on carrier types, n-type and p-type WSe{sub 2} FETs are fabricated with different work function metals. Each device has similar electrical characteristics except for the threshold voltage. In the low frequency noise analysis, drain current power spectral density (S{sub I}) is inversely proportional to frequency, indicating typical 1/f noise behaviors. The curves of the normalized drain current power spectral density (NS{sub I}) as a function of drain current at the 10 Hz of frequency indicate that our devices follow the carrier number fluctuation with correlated mobility fluctuation model. This means that current fluctuation depends on the trapping-detrapping motion of the charge carriers near the channel interface. No significant difference is observed in the current fluctuation according to the charge carrier type, electrons and holes that occurred in the junction and channel region.

  7. Completely independent electrical control of spin and valley in a silicene field effect transistor

    Science.gov (United States)

    Zhai, Xuechao; Jin, Guojun

    2016-09-01

    One-atom-thick silicene is a silicon-based hexagonal-lattice material with buckled structure, where an electron fuses multiple degrees of freedom including spin, sublattice pseudospin and valley. We here demonstrate that a valley-selective spin filter (VSSF) that supports single-valley and single-spin transport can be realized in a silicene field effect transistor constructed of an npn junction, where an antiferromagnetic exchange field and a perpendicular electric field are applied in the p-doped region. The nontrivial VSSF property benefits from an electrically controllable state of spin-polarized single-valley Dirac cone. By reversing the electric field direction, the device can operate as a spin-reversed but valley-unreversed filter due to the dependence of band gap on spin and valley. Further, we find that all the possible spin-valley configurations of VSSF can be achieved just by tuning the electric field. Our findings pave the way to the realization of completely independent electrical control of spin and valley in silicene circuits.

  8. Exploring graphene field effect transistor devices to improve spectral resolution of semiconductor radiation detectors

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Richard Karl [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Howell, Stephen Wayne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martin, Jeffrey B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hamilton, Allister B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2013-12-01

    Graphene, a planar, atomically thin form of carbon, has unique electrical and material properties that could enable new high performance semiconductor devices. Graphene could be of specific interest in the development of room-temperature, high-resolution semiconductor radiation spectrometers. Incorporating graphene into a field-effect transistor architecture could provide an extremely high sensitivity readout mechanism for sensing charge carriers in a semiconductor detector, thus enabling the fabrication of a sensitive radiation sensor. In addition, the field effect transistor architecture allows us to sense only a single charge carrier type, such as electrons. This is an advantage for room-temperature semiconductor radiation detectors, which often suffer from significant hole trapping. Here we report on initial efforts towards device fabrication and proof-of-concept testing. This work investigates the use of graphene transferred onto silicon and silicon carbide, and the response of these fabricated graphene field effect transistor devices to stimuli such as light and alpha radiation.

  9. Highly stable organic polymer field-effect transistor sensor for selective detection in the marine environment.

    Science.gov (United States)

    Knopfmacher, Oren; Hammock, Mallory L; Appleton, Anthony L; Schwartz, Gregor; Mei, Jianguo; Lei, Ting; Pei, Jian; Bao, Zhenan

    2014-01-01

    In recent decades, the susceptibility to degradation in both ambient and aqueous environments has prevented organic electronics from gaining rapid traction for sensing applications. Here we report an organic field-effect transistor sensor that overcomes this barrier using a solution-processable isoindigo-based polymer semiconductor. More importantly, these organic field-effect transistor sensors are stable in both freshwater and seawater environments over extended periods of time. The organic field-effect transistor sensors are further capable of selectively sensing heavy-metal ions in seawater. This discovery has potential for inexpensive, ink-jet printed, and large-scale environmental monitoring devices that can be deployed in areas once thought of as beyond the scope of organic materials.

  10. Field-Effect Transistors: Ultrathin MXene-Micropattern-Based Field-Effect Transistor for Probing Neural Activity (Adv. Mater. 17/2016).

    Science.gov (United States)

    Xu, Bingzhe; Zhu, Minshen; Zhang, Wencong; Zhen, Xu; Pei, Zengxia; Xue, Qi; Zhi, Chunyi; Shi, Peng

    2016-05-01

    A field-effect transistor (FET) based on ultrathin Ti3 C2 -MXene micropatterns is developed by C. Zhi, P. Shi, and co-workers, as described on page 3333. The FET can be utilized for label-free probing of small molecules in typical biological environments, e.g., for fast detection of action potentials in primary neurons. This device is produced with a microcontact printing technique, harnessing the unique advantages for easy fabrication.

  11. Photoconductive and supramolecularly engineered organic field-effect transistors based on fibres from donor-acceptor dyads

    Science.gov (United States)

    Treier, Matthias; Liscio, Andrea; Mativetsky, Jeffrey M.; Kastler, Marcel; Müllen, Klaus; Palermo, Vincenzo; Samorì, Paolo

    2012-02-01

    We report on the formation of photoconductive self-assembled fibres by solvent induced precipitation of a HBC-PMI donor-acceptor dyad. Kelvin Probe Force Microscopy revealed that upon illumination with white light the surface potential of the fibres shifted to negative values due to a build-up of negative charge. When integrated in a field-effect transistor (FET) configuration, the devices can be turned `on' much more efficiently using light than conventional bias triggered field-effect, suggesting that these structures could be used for the fabrication of light sensing devices. Such a double gating represents an important step towards bi-functional organic FETs, in which the current through the junction can be modulated both optically (by photoexcitation) and electrically (by gate control).We report on the formation of photoconductive self-assembled fibres by solvent induced precipitation of a HBC-PMI donor-acceptor dyad. Kelvin Probe Force Microscopy revealed that upon illumination with white light the surface potential of the fibres shifted to negative values due to a build-up of negative charge. When integrated in a field-effect transistor (FET) configuration, the devices can be turned `on' much more efficiently using light than conventional bias triggered field-effect, suggesting that these structures could be used for the fabrication of light sensing devices. Such a double gating represents an important step towards bi-functional organic FETs, in which the current through the junction can be modulated both optically (by photoexcitation) and electrically (by gate control). Electronic supplementary information (ESI) available: Experimental details and photoresponse on spin-coated film (3 pages). See DOI: 10.1039/c2nr11635a

  12. High mobility polymer gated organic field effect transistor using zinc phthalocyanine

    Indian Academy of Sciences (India)

    K R Rajesh; V Kannan; M R Kim; Y S Chae; J K Rhee

    2014-02-01

    Organic thin film transistors were fabricated using evaporated zinc phthalocyanine as the active layer. Parylene film prepared by chemical vapour deposition was used as the organic gate insulator. The annealing of the samples was performed at 120°C for 3 h. At room temperature, these transistors exhibit -type conductivity with field-effect mobilities ranging from 0.025–0.037 cm2/Vs and a (on/off) ratio of ∼ 103. The effect of annealing on transistor characteristics is discussed.

  13. Total ionizing dose effects in multiple-gate field-effect transistor

    Science.gov (United States)

    Gaillardin, Marc; Marcandella, Claude; Martinez, Martial; Raine, Mélanie; Paillet, Philippe; Duhamel, Olivier; Richard, Nicolas

    2017-08-01

    This paper focuses on total ionizing dose (TID) effects induced in multiple-gate field-effect transistors. The impact of device architecture, geometry and scaling on the TID response of multiple-gate transistors is reviewed in both bulk and silicon-on-insulator (SOI) complementary metal-oxide-semiconductor (CMOS) technologies. These innovating devices exhibit specific ionizing dose responses which strongly depend on their three-dimensional nature. Their TID responses may look like the one usually observed in planar two-dimensional bulk or SOI transistors, but multiple-gate devices can also behave like any other CMOS device.

  14. Proton migration mechanism for the instability of organic field-effect transistors

    Science.gov (United States)

    Sharma, A.; Mathijssen, S. G. J.; Kemerink, M.; de Leeuw, D. M.; Bobbert, P. A.

    2009-12-01

    During prolonged application of a gate bias, organic field-effect transistors show an instability involving a gradual shift of the threshold voltage toward the applied gate bias voltage. We propose a model for this instability in p-type transistors with a silicon-dioxide gate dielectric, based on hole-assisted production of protons in the accumulation layer and their subsequent migration into the gate dielectric. This model explains the much debated role of water and several other hitherto unexplained aspects of the instability of these transistors.

  15. Top Contact Pentacene Organic Thin Film Field Effect Transistors

    Institute of Scientific and Technical Information of China (English)

    ZHANG Su-mei; SHI Jia-wei; SHI Ying-xue; GUO Shu-xu; LIU Ming-da; MA Dong-ge; CHEN Jiang-shan

    2004-01-01

    Using pentacene as an active material, the organic thin film transistors were fabricated on Si3N4/p-Si substrates by using RF-magnetron sputtered amorphous aluminium as the gate electrode contact, and using highly doped Si as the gate electrode and substrate with plasma-enhanced chemical vapor deposited (PECVD) silicon nitride as gate dielectric. Pentacene thin films were deposited by thermal evaporation on dielectrics as the active layer, then RF-magnetron sputtered amorphous aluminium was used as the source and drain contacts. Measurement results show that field respectively, and on-off current ratio is nearly 1×103.

  16. Anomalous current transients in organic field-effect transistors

    Science.gov (United States)

    Sharma, A.; Mathijssen, S. G. J.; Cramer, T.; Kemerink, M.; de Leeuw, D. M.; Bobbert, P. A.

    2010-03-01

    Here we study the origin of the gate bias-stress effect in organic p-type transistors. Based on water-mediated exchange between holes in the semiconductor and protons in the gate dielectric, we predict anomalous current transients for a non-constant gate bias, while ensuring accumulation. When applying a strongly negative gate bias followed by a less negative bias a back-transfer of protons to holes and an increase of the current is expected. We verify this counterintuitive behavior experimentally and can quantitatively model the transients with the same parameters as used to describe the threshold voltage shift.

  17. Top contact organic field effect transistors fabricated using a photolithographic process

    Institute of Scientific and Technical Information of China (English)

    Wang Hong; Ji zhuo-Yu; Shang Li-Wei; Liu Xing-Hua; Peng Ying-Quan; Liu Ming

    2011-01-01

    This paper proposes an effective method of fabricating top contact organic field effect transistors by using a photolithographic process.The semiconductor layer is protected by a passivation layer.Through photolithographic and etching processes,parts of the passivation layer are etched off to form source/drain electrode patterns.Combined with conventional evaporation and lift-off techniques,organic field effect transistors with a top contact are fabricated successfully,whose properties are comparable to those prepared with the shadow mask method and one order of magnitude higher than the bottom contact devices fabricated by using a photolithographic process.

  18. Organic field-effect transistor nonvolatile memories utilizing sputtered C nanoparticles as nano-floating-gate

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Jie; Liu, Chang-Hai; She, Xiao-Jian; Sun, Qi-Jun; Gao, Xu; Wang, Sui-Dong, E-mail: wangsd@suda.edu.cn [Institute of Functional Nano and Soft Materials (FUNSOM), Soochow University, Suzhou, Jiangsu 215123 (China)

    2014-10-20

    High-performance organic field-effect transistor nonvolatile memories have been achieved using sputtered C nanoparticles as the nano-floating-gate. The sputtered C nano-floating-gate is prepared with low-cost material and simple process, forming uniform and discrete charge trapping sites covered by a smooth and complete polystyrene layer. The devices show large memory window, excellent retention capability, and programming/reading/erasing/reading endurance. The sputtered C nano-floating-gate can effectively trap both holes and electrons, and it is demonstrated to be suitable for not only p-type but also n-type organic field-effect transistor nonvolatile memories.

  19. Polyfluorenes as organic semiconductors for polymeric field effect transistors

    Science.gov (United States)

    Brennan, David J.; Townsend, Paul H., III; Welsh, Dean M.; Dibbs, Mitchell G.; Shaw, Jeff M.; Miklovich, Jessica L.; Boeke, Robyn B.; Arias, Ana Claudia; Creswell, Lisa; MacKenzie, J. D.; Ramsdale, Catherine; Menon, Anoop; Sirringhaus, Henning

    2003-11-01

    Well-characterized F8T2 polyfluorene (Dow Chemical) has been prepared with weight average molecular weights (Mw) ranging from about 20,000 to 120,000. This semiconducting polymer has been used by Plastic Logic to fabricate arrays of 4,800 thin film transistors (TFTs) with 50 dpi, to be used as backplanes for active matrix displays. In this paper, the effects that molecular weight and thermal treatment have on the electrical characteristics of F8T2-based TFTs are reported. First, transistor performance improves with increasing molecular weight, with maximum values of TFT mobility approaching 1x 10-2 cm2 /V-s. Consistently higher mobilities are obtained when the F8T2 semiconductor makes contact with PEDOT/PSS versus gold electrodes. Alignment of F8T2 on a rubbed polyimide substrate is maintained after quenching, as determined by measurement of the dichroic ratios. Early-stage results on the development of inks based on F8T2 polyfluorene are also reported.

  20. Theoretical study of the source-drain current and gate leakage current to understand the graphene field-effect transistors.

    Science.gov (United States)

    Yu, Cui; Liu, Hongmei; Ni, Wenbin; Gao, Nengyue; Zhao, Jianwei; Zhang, Haoli

    2011-02-28

    We designed acene molecules attached to two semi-infinite metallic electrodes to explore the source-drain current of graphene and the gate leakage current of the gate dielectric material in the field-effect transistors (FETs) device using the first-principles density functional theory combined with the non-equilibrium Green's function formalism. In the acene-based molecular junctions, we modify the connection position of the thiol group at one side, forming different electron transport routes. The electron transport routes besides the shortest one are defined as the cross channels. The simulation results indicate that electron transport through the cross channels is as efficient as that through the shortest one, since the conductance is weakly dependent on the distance. Thus, it is possible to connect the graphene with multiple leads, leading the graphene as a channel utilized in the graphene-based FETs in the mesoscopic system. When the conjugation of the cross channel is blocked, the junction conductance decreases dramatically. The differential conductance of the BA-1 is nearly 7 (54.57 μS) times as large as that of the BA-4 (7.35 μS) at zero bias. Therefore, the blocked graphene can be employed as the gate dielectric material in the top-gated graphene FET device, since the leakage current is small. The graphene-based field-effect transistors fabricated with a single layer of graphene as the channel and the blocked graphene as the gate dielectric material represent one way to overcome the problem of miniaturization which faces the new generation of transistors.

  1. Fabrication of pentacene organic field-effect transistors with polyimide gate dielectric layer

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The organic field effect transistors had been fabricated using the pentacene by vacuum evaporation as the active layer, the polyimide by spin coating as insulator layer, and aluminum by vacuum evaporation as gate, source and drain electrodes respectively. The field-effect mobility of 0.079 cm2/V.s was tested at Vds=70 V, and on/off radio up to 1.7×104.

  2. Microstructure-mobility correlation in self-organised, conjugated polymer field-effect transistors

    DEFF Research Database (Denmark)

    Sirringhaus, H.; Brown, P.J.; Friend, R.H.

    2000-01-01

    We have investigated the correlation between polymer microstructure and charge carrier mobility in high-mobility, self-organised field-effect transistors of poly-3-hexyl-thiophene (P3HT). Two different preferential orientations of the microcrystalline P3HT domains with respect to the substrate have...... the charge transport properties of conjugated polymer field-effect devices. (C) 2000 Elsevier Science S.A. All rights reserved....

  3. Ferroelectric-gate field effect transistor memories device physics and applications

    CERN Document Server

    Ishiwara, Hiroshi; Okuyama, Masanori; Sakai, Shigeki; Yoon, Sung-Min

    2016-01-01

    This book provides comprehensive coverage of the materials characteristics, process technologies, and device operations for memory field-effect transistors employing inorganic or organic ferroelectric thin films. This transistor-type ferroelectric memory has interesting fundamental device physics and potentially large industrial impact. Among the various applications of ferroelectric thin films, the development of nonvolatile ferroelectric random access memory (FeRAM) has progressed most actively since the late 1980s and has achieved modest mass production levels for specific applications since 1995. There are two types of memory cells in ferroelectric nonvolatile memories. One is the capacitor-type FeRAM and the other is the field-effect transistor (FET)-type FeRAM. Although the FET-type FeRAM claims ultimate scalability and nondestructive readout characteristics, the capacitor-type FeRAMs have been the main interest for the major semiconductor memory companies, because the ferroelectric FET has fatal handic...

  4. A hydrogel capsule as gate dielectric in flexible organic field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Dumitru, L. M.; Manoli, K.; Magliulo, M.; Torsi, L., E-mail: luisa.torsi@uniba.it [Department of Chemistry, University of Bari “Aldo Moro”, Via Orabona 4, Bari I-70126 (Italy); Ligonzo, T. [Department of Physics, University of Bari “Aldo Moro”, Via Orabona 4, Bari I-70126 (Italy); Palazzo, G. [Department of Chemistry, University of Bari “Aldo Moro”, Via Orabona 4, Bari I-70126 (Italy); Center of Colloid and Surface Science—CSGI—Bari Unit, Via Orabona 4, Bari I-70126 (Italy)

    2015-01-01

    A jellified alginate based capsule serves as biocompatible and biodegradable electrolyte system to gate an organic field-effect transistor fabricated on a flexible substrate. Such a system allows operating thiophene based polymer transistors below 0.5 V through an electrical double layer formed across an ion-permeable polymeric electrolyte. Moreover, biological macro-molecules such as glucose-oxidase and streptavidin can enter into the gating capsules that serve also as delivery system. An enzymatic bio-reaction is shown to take place in the capsule and preliminary results on the measurement of the electronic responses promise for low-cost, low-power, flexible electronic bio-sensing applications using capsule-gated organic field-effect transistors.

  5. Localized heating on silicon field effect transistors: device fabrication and temperature measurements in fluid.

    Science.gov (United States)

    Elibol, Oguz H; Reddy, Bobby; Nair, Pradeep R; Dorvel, Brian; Butler, Felice; Ahsan, Zahab S; Bergstrom, Donald E; Alam, Muhammad A; Bashir, Rashid

    2009-10-07

    We demonstrate electrically addressable localized heating in fluid at the dielectric surface of silicon-on-insulator field-effect transistors via radio-frequency Joule heating of mobile ions in the Debye layer. Measurement of fluid temperatures in close vicinity to surfaces poses a challenge due to the localized nature of the temperature profile. To address this, we developed a localized thermometry technique based on the fluorescence decay rate of covalently attached fluorophores to extract the temperature within 2 nm of any oxide surface. We demonstrate precise spatial control of voltage dependent temperature profiles on the transistor surfaces. Our results introduce a new dimension to present sensing systems by enabling dual purpose silicon transistor-heaters that serve both as field effect sensors as well as temperature controllers that could perform localized bio-chemical reactions in Lab on Chip applications.

  6. Benzocyclobutene (BCB) Polymer as Amphibious Buffer Layer for Graphene Field-Effect Transistor.

    Science.gov (United States)

    Wu, Yun; Zou, Jianjun; Huo, Shuai; Lu, Haiyan; Kong, Yuecan; Chen, Tangshen; Wu, Wei; Xu, Jingxia

    2015-08-01

    Owing to the scattering and trapping effects, the interfaces of dielectric/graphene or substrate/graphene can tailor the performance of field-effect transistor (FET). In this letter, the polymer of benzocyclobutene (BCB) was used as an amphibious buffer layer and located at between the layers of substrate and graphene and between the layers of dielectric and graphene. Interestingly, with the help of nonpolar and hydrophobic BCB buffer layer, the large-scale top-gated, chemical vapor deposited (CVD) graphene transistors was prepared on Si/SiO2 substrate, its cutoff frequency (fT) and the maximum cutoff frequency (fmax) of the graphene field-effect transistor (GFET) can be reached at 12 GHz and 11 GHz, respectively.

  7. Controlling the on/off current ratio of ferroelectric field-effect transistors

    NARCIS (Netherlands)

    Katsouras, I.; Zhao, D.; Spijkman, M.J.; Li, M.; Blom, P.W.M.; Leeuw, D.M. de; Asadi, K.

    2015-01-01

    The on/off current ratio in organic ferroelectric field-effect transistors (FeFETs) is largely determined by the position of the threshold voltage, the value of which can show large device-to-device variations. Here we show that by employing a dual-gate layout for the FeFET, we can gain full control

  8. Ambipolar Cu- and Fe-phthalocyanine single-crystal field-effect transistors

    NARCIS (Netherlands)

    De Boer, R.W.I.; Stassen, A.F.; Craciun, M.F.; Mulder, C.L.; Molinari, A.; Rogge, S.; Morpurgo, A.F.

    2005-01-01

    We report the observation of ambipolar transport in field-effect transistors fabricated on single crystals of copper- and iron-phthalocyanine, using gold as a high work-function metal for the fabrication of source and drain electrodes. In these devices, the room-temperature mobility of holes reaches

  9. A Dynamic Simulation on Single Gate Junctionless Field Effect Transistor Based on Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Roya Norani

    Full Text Available We study the I-V characteristics of single gate junctionless field effect transistor by device simulation. The sample FET is simulated at different channel lengths and the I-V curve changes due to variations of and channel length have been systematically ...

  10. Reproducible low contact resistance in rubrene single-crystal field-effect transistors with nickel electrodes

    NARCIS (Netherlands)

    Hulea, I.N.; Russo, S.; Molinari, A.; Morpurgo, A.F.

    2006-01-01

    We have investigated the contact resistance of rubrene single-crystal field-effect transistors (FETs) with nickel electrodes by performing scaling experiments on devices with channel length ranging from 200 nm up to 300 μm. We find that the contact resistance can be as low as 100 Ω cm with narrowly

  11. MOBILITAS PEMBAWA MUATAN PADA OFET (ORGANIC FIELD EFFECT TRANSISTOR) BERBASIS FILM TIPIS

    OpenAIRE

    Sujarwata -; P. Marwoto

    2014-01-01

    Abstrak __________________________________________________________________________________________ Tujuan penelitian ini adalah pembuatan dan karakterisasi pada OFET (Organic Field Effect Transistor) berbasis film tipis dengan struktur bottom-contact. Pembuatan OFET dilakukan dengan cara pencucian substrat dengan etanol dalam ultrasonic cleaner, kemudian dilakukan deposisi elektroda source dan drain di atas substrat SiO2 dengan metode  penguapan hampa udara pada suhu ruang dan teknik lithogra...

  12. Hole transport in polymeric field-effect transistors and light-emitting diodes

    NARCIS (Netherlands)

    Tanase, C; Blom, PWM; Meijer, EJ; de Leeuw, DM; Dimitrakopoulos, CD; Dodabalapur, A

    2003-01-01

    The hole transport in the amorphous poly(2-methoxy-5-(3',7'-dimethyloctyloxy)-p-phenylene vinylene) (OC1C10-PPV) and in the more ordered poly[2,5-bis(3',7'-dimethyloctyloxy)-p-phenylene vinylene] (OC10C10-PPV) has been investigated both in field-effect transistors (FETs) and light-emitting diodes (L

  13. IC Compatible Wafer Level Fabrication of Silicon Nanowire Field Effect Transistors for Biosensing Applications

    NARCIS (Netherlands)

    Moh, T.S.Y.

    2013-01-01

    In biosensing, nano-devices such as Silicon Nanowire Field Effect Transistors (SiNW FETs) are promising components/sensors for ultra-high sensitive detection, especially when samples are low in concentration or a limited volume is available. Current processing of SiNW FETs often relies on expensive

  14. Origin of multiple memory states in organic ferroelectric field-effect transistors

    NARCIS (Netherlands)

    Kam, B.; Li, X.; Cristoferi, C.; Smits, E.C.P.; Mityashin, A.; Schols, S.; Genoe, J.; Gelinck, G.H.; Heremans, P.

    2012-01-01

    In this work, we investigate the ferroelectric polarization state in metal-ferroelectric-semiconductor-metal structures and in ferroelectric field-effect transistors (FeFET). Poly(vinylidene fluoride-trifluoroethylene) and pentacene was used as the ferroelectric and semiconductor, respectively. This

  15. Neutral anion receptors; synthesis and evaluation as sensing molecules in chemically modified field effect transistors (CHEMFETs)

    NARCIS (Netherlands)

    Antonisse, Martijn M.G.; Snellink-Ruel, Bianca H.M.; Yigit, Isteyfo; Engbersen, Johan F.J.; Reinhoudt, David N.

    1997-01-01

    new class of anion selective receptors is based on the neutral uranylsalophene building block as Lewis acidic binding site. Additional hydrogen bond accepting or donating moieties near the anion binding site offer the possibility of varying the binding selectivity. Field effect transistors chemicall

  16. The ion-sensitive field effect transistor in rapid acid-base titrations

    NARCIS (Netherlands)

    Bos, M.; Bergveld, P.; Veen-Blaauw, van A.M.W.

    1979-01-01

    Ion-sensitive field effect transistors (ISFETs) are used as the pH sensor in rapid acid—base titrations. Titration speeds at least five times greater than those with glass electrodes are possible for accuracies better than ±1%.

  17. Organic single-crystal light-emitting field-effect transistors

    NARCIS (Netherlands)

    Hotta, Shu; Yamao, Takeshi; Bisri, Satria Zulkarnaen; Takenobu, Taishi; Iwasa, Yoshihiro

    2014-01-01

    Growth and characterisation of single crystals constitute a major field of materials science. In this feature article we overview the characteristics of organic single-crystal light-emitting field-effect transistors (OSCLEFETs). The contents include the single crystal growth of organic semiconductor

  18. Bias-dependent contact resistance in rubrene single-crystal field-effect transistors

    NARCIS (Netherlands)

    Molinari, A.; Gutiérrez, I.; Hulea, I.N.; Russo, S.; Morpurgo, A.F.

    2007-01-01

    The authors report a systematic study of the bias-dependent contact resistance in rubrene single-crystal field-effect transistors with Ni, Co, Cu, Au, and Pt electrodes. They show that the reproducibility in the values of contact resistance strongly depends on the metal, ranging from a factor of 2 f

  19. Ambipolar Cu- and Fe-phthalocyanine single-crystal field-effect transistors

    NARCIS (Netherlands)

    De Boer, R.W.I.; Stassen, A.F.; Craciun, M.F.; Mulder, C.L.; Molinari, A.; Rogge, S.; Morpurgo, A.F.

    2005-01-01

    We report the observation of ambipolar transport in field-effect transistors fabricated on single crystals of copper- and iron-phthalocyanine, using gold as a high work-function metal for the fabrication of source and drain electrodes. In these devices, the room-temperature mobility of holes reaches

  20. DNA adsorption measured with ultra-thin film organic field effect transistors

    NARCIS (Netherlands)

    Stoliar, P.; Bystrenova, E.; Quiroga, S.D.; Annibale, P.; Facchini, M.; Spijkman, M.; Setayesh, S.; Leeuw, D. de; Biscarini, F.

    2009-01-01

    Organic ultra-thin film field effect transistors (FET) are operated as label-free sensors of deoxyribonucleic acid (DNA) adsorption. Linearized plasmid DNA molecules (4361 base pairs) are deposited froma solution on two monolayers thick pentacene FET. The amount of adsorbed DNA is measured by AFM an

  1. Gas sensing with self-assembled monolayer field-effect transistors

    NARCIS (Netherlands)

    Andringa, A-M.; Spijkman, M-J.; Mathijssen, S.G.J.; Smits, E.C.P.; Hal, P.A. van; Setayesh, S.; Willard, N.P.; Borshchev, O.V.; Ponomarenko, S.A.; Blom, P.W.M.; Leeuw, D.M. de

    2010-01-01

    A new sensitive gas sensor based on a self-assembled monolayer field-effect transistor (SAMFET) was used to detect the biomarker nitric oxide. A SAMFET based sensor is highly sensitive because the analyte and the active channel are separated by only one monolayer. SAMFETs were functionalised for dir

  2. IC Compatible Wafer Level Fabrication of Silicon Nanowire Field Effect Transistors for Biosensing Applications

    NARCIS (Netherlands)

    Moh, T.S.Y.

    2013-01-01

    In biosensing, nano-devices such as Silicon Nanowire Field Effect Transistors (SiNW FETs) are promising components/sensors for ultra-high sensitive detection, especially when samples are low in concentration or a limited volume is available. Current processing of SiNW FETs often relies on expensive

  3. Electric field confinement effect on charge transport in organic field-effect transistors

    NARCIS (Netherlands)

    Li, X.; Kadashchuk, A.; Fishchuk, I.I.; Smaal, W.T.T.; Gelinck, G.H.; Broer, D.J.; Genoe, J.; Heremans, P.; Bässler, H.

    2012-01-01

    While it is known that the charge-carrier mobility in organic semiconductors is only weakly dependent on the electric field at low fields, the experimental mobility in organic field-effect transistors using silylethynyl-substituted pentacene is found to be surprisingly field dependent at low source-

  4. A simple model for atomic layer doped field-effect transistor (ALD-FET) electronic states

    Energy Technology Data Exchange (ETDEWEB)

    Mora R, M.E. [Centro de Investigaciones en Optica, Unidad Aguascalientes. Juan de Montoro 207, Zona Centro, 20000 Aguascalientes (Mexico); Gaggero S, L.M. [Escuela de Fisica, Universidad Autonoma de Zacatecas, Av. Preparatoria 301, 98060 Zacatecas (Mexico)

    1998-12-31

    We propose a simple potential model based on the Thomas-Fermi approximation to reproduce the main properties of the electronic structure of an atomic layer doped field effect transistor. Preliminary numerical results for a Si-based ALD-FET justify why bound electronic states are not observed in the experiment. (Author)

  5. High-performance solution-processed polymer ferroelectric field-effect transistors

    NARCIS (Netherlands)

    Naber, RCG; Tanase, C; Blom, PWM; Gelinck, GH; Marsman, AW; Touwslager, FJ; Setayesh, S; De Leeuw, DM; Naber, Ronald C.G.; Gelinck, Gerwin H.; Marsman, Albert W.; Touwslager, Fred J.

    2005-01-01

    We demonstrate a rewritable, non-volatile memory device with flexible plastic active layers deposited from solution. The memory device is a ferroelectric field-effect transistor (FeFET) made with a ferroelectric fluoropolymer and a bisalkoxy-substituted poly(p-phenylene vinylene) semiconductor mater

  6. The Influence of Morphology on High-Performance Polymer Field-Effect Transistors

    DEFF Research Database (Denmark)

    Tsao, Hoi Nok; Cho, Don; Andreasen, Jens Wenzel

    2009-01-01

    The influence of molecular packing on the performance of polymer organic field-effect transistors is illustrated in this work. Both close -stacking distance and long-range order are important for achieving high mobilities. By aligning the polymers from solution, long-range order is induced...

  7. High Performance Ambipolar Field-Effect Transistor of Random Network Carbon Nanotubes

    NARCIS (Netherlands)

    Bisri, Satria Zulkarnaen; Gao, Jia; Derenskyi, Vladimir; Gomulya, Widianta; Iezhokin, Igor; Gordiichuk, Pavlo; Herrmann, Andreas; Loi, Maria Antonietta

    2012-01-01

    Ambipolar field-effect transistors of random network carbon nanotubes are fabricated from an enriched dispersion utilizing a conjugated polymer as the selective purifying medium. The devices exhibit high mobility values for both holes and electrons (3 cm(2)/V.s) with a high on/off ratio (10(6)). The

  8. Unification of the hole transport in polymeric field-effect transistors and light-emitting diodes

    NARCIS (Netherlands)

    Tanase, C; Meijer, EJ; Blom, PWM; de Leeuw, DM

    2003-01-01

    A systematic study of the hole mobility in hole-only diodes and field-effect transistors based on poly(2-methoxy-5-(3('),7(')-dimethyloctyloxy)-p-phenylene vinylene) and on amorphous poly(3-hexyl thiophene) has been performed as a function of temperature and applied bias. The experimental hole mobil

  9. Near-Infrared Light-Emitting Ambipolar Organic Field-Effect Transistors

    NARCIS (Netherlands)

    Smits, E.C.P.; Setayesh, S.; Anthopoulos, T.D.; Buechel, M.; Nijssen, W.; Coehoorn, R.; Blom, P.W.M.; Leeuw, D.M. de

    2006-01-01

    Recent years have seen tremendous advances in the area of organic-based optoelectronic devices and several applications previously envisioned are now reaching the stage of commercial exploitation.[1] Organic field-effect transistors (OFETs) are among these devices and can be arguably viewed as a pos

  10. Wide-bandwidth charge sensitivity with a radio-frequency field-effect transistor

    NARCIS (Netherlands)

    Nishiguchi, K.; Yamaguchi, H.; Fujiwara, A.; Van der Zant, H.S.J.; Steele, G.A.

    2013-01-01

    We demonstrate high-speed charge detection at room temperature with single-electron resolution by using a radio-frequency field-effect transistor (RF-FET). The RF-FET combines a nanometer-scale silicon FET with an impedance-matching circuit composed of an inductor and capacitor. Driving the RF-FET w

  11. Terahertz 3D printed diffractive lens matrices for field-effect transistor detector focal plane arrays.

    Science.gov (United States)

    Szkudlarek, Krzesimir; Sypek, Maciej; Cywiński, Grzegorz; Suszek, Jarosław; Zagrajek, Przemysław; Feduniewicz-Żmuda, Anna; Yahniuk, Ivan; Yatsunenko, Sergey; Nowakowska-Siwińska, Anna; Coquillat, Dominique; But, Dmytro B; Rachoń, Martyna; Węgrzyńska, Karolina; Skierbiszewski, Czesław; Knap, Wojciech

    2016-09-05

    We present the concept, the fabrication processes and the experimental results for materials and optics that can be used for terahertz field-effect transistor detector focal plane arrays. More specifically, we propose 3D printed arrays of a new type - diffractive multi-zone lenses of which the performance is superior to that of previously used mono-zone diffractive or refractive elements and evaluate them with GaN/AlGaN field-effect transistor terahertz detectors. Experiments performed in the 300-GHz atmospheric window show that the lens arrays offer both a good efficiency and good uniformity, and may improve the signal-to-noise ratio of the terahertz field-effect transistor detectors by more than one order of magnitude. In practice, we tested 3 × 12 lens linear arrays with printed circuit board THz detector arrays used in postal security scanners and observed significant signal-to-noise improvements. Our results clearly show that the proposed technology provides a way to produce cost-effective, reproducible, flat optics for large-size field-effect transistor THz-detector focal plane arrays.

  12. Wafer-Scale Gigahertz Graphene Field Effect Transistors on SiC Substrates

    Institute of Scientific and Technical Information of China (English)

    潘洪亮; 金智; 麻芃; 郭建楠; 刘新宇; 叶甜春; 李佳; 敦少博; 冯志红

    2011-01-01

    Wafer-scale graphene field-effect transistors are fabricated using benzocyclobutene and atomic layer deposition Al2O3 as the top-gate dielectric.The epitaxial-graphene layer is formed by graphitization of a 2-inch-diameter Si-face semi-insulating 6H-SiC substrate.The graphene on the silicon carbide substrate is heavily n-doped and current saturation is not found.For the intrinsic characteristic of this particular channel material,the devices cannot be switched off.The cut-off frequencies of these graphene field-effect transistors,which have a gate length of l μm,are larger than 800 MHz.The largest one can reach 1.24 GHz.There are greater than 95% active devices that can be successfully applied.We thus succeed in fabricating wafer-scale gigahertz graphene field-effect transistors,which paves the way for high-performance graphene devices and circuits.%Wafer-scale graphene Beld-effect transistors are fabricated using benzocyclobutene and atomic layer deposition AI2O3 as the top-gate dielectric. The epitaxial-graphene layer is formed by graphitization of a 2-inch-diameter Si-face semi-insulating 6H-SiC substrate. The graphene on the silicon carbide substrate is heavily n-doped and current saturation is not found. For the intrinsic characteristic of this particular channel material, the devices cannot be switched off. The cut-off frequencies of these graphene field-effect transistors, which have a gate length of l μm, are larger than 800MHz. The largest one can reach 1.24 GHz. There are greater than 95% active devices that can be successfully applied. We thus succeed in fabricating wafer-scale gigahertz graphene Geld-effect transistors, which paves the way for high-performance graphene devices and circuits.

  13. Schottky barrier contrasts in single and bi-layer graphene contacts for MoS2 field-effect transistors

    Science.gov (United States)

    Du, Hyewon; Kim, Taekwang; Shin, Somyeong; Kim, Dahye; Kim, Hakseong; Sung, Ji Ho; Lee, Myoung Jae; Seo, David H.; Lee, Sang Wook; Jo, Moon-Ho; Seo, Sunae

    2015-12-01

    We have investigated single- and bi-layer graphene as source-drain electrodes for n-type MoS2 transistors. Ti-MoS2-graphene heterojunction transistors using both single-layer MoS2 (1M) and 4-layer MoS2 (4M) were fabricated in order to compare graphene electrodes with commonly used Ti electrodes. MoS2-graphene Schottky barrier provided electron injection efficiency up to 130 times higher in the subthreshold regime when compared with MoS2-Ti, which resulted in VDS polarity dependence of device parameters such as threshold voltage (VTH) and subthreshold swing (SS). Comparing single-layer graphene (SG) with bi-layer graphene (BG) in 4M devices, SG electrodes exhibited enhanced device performance with higher on/off ratio and increased field-effect mobility (μFE) due to more sensitive Fermi level shift by gate voltage. Meanwhile, in the strongly accumulated regime, we observed opposing behavior depending on MoS2 thickness for both SG and BG contacts. Differential conductance (σd) of 1M increases with VDS irrespective of VDS polarity, while σd of 4M ceases monotonic growth at positive VDS values transitioning to ohmic-like contact formation. Nevertheless, the low absolute value of σd saturation of the 4M-graphene junction demonstrates that graphene electrode could be unfavorable for high current carrying transistors.

  14. Beyond the Nernst-limit with dual-gate ZnO ion-sensitive field-effect transistors

    NARCIS (Netherlands)

    Spijkman, M.; Smits, E.C.P.; Cillessen, J.F.M.; Biscarini, F.; Blom, P.W.M.; Leeuw, D.M. de

    2011-01-01

    The sensitivity of conventional ion-sensitive field-effect transistors (ISFETs) is limited to 59 mV/pH, which is the maximum detectable change in electrochemical potential according to the Nernst equation. Here we demonstrate a transducer based on a ZnO dual-gate field-effect transistor that breache

  15. Simulation-based design of a strained graphene field effect transistor incorporating the pseudo magnetic field effect

    Energy Technology Data Exchange (ETDEWEB)

    Souma, Satofumi, E-mail: ssouma@harbor.kobe-u.ac.jp; Ueyama, Masayuki; Ogawa, Matsuto [Department of Electrical and Electronic Engineering, Kobe University, 1-1 Rokkodai, Nada, Kobe 657-8501 (Japan)

    2014-05-26

    We present a numerical study on the performance of strained graphene-based field-effect transistors. A local strain less than 10% is applied over a central channel region of the graphene to induce the shift of the Dirac point in the channel region along the transverse momentum direction. The left and the right unstrained graphene regions are doped to be either n-type or p-type. By using the atomistic tight-binding model and a Green's function method, we predict that the gate voltage applied to the central strained graphene region can switch the drain current on and off with an on/off ratio of more than six orders of magnitude at room temperature. This is in spite of the absence of a bandgap in the strained channel region. Steeper subthreshold slopes below 60 mV/decade are also predicted at room temperature because of a mechanism similar to the band-to-band tunneling field-effect transistors.

  16. Charge Transport in Field-Effect Transistors based on Layered Materials and their Heterostructures

    Science.gov (United States)

    Kumar, Jatinder

    In the quest for energy efficiency and device miniaturization, the research in using atomically thin materials for device applications is gaining momentum. The electronic network in layered materials is different from 3D counterparts. It is due to the interlayer couplings and density of states because of their 2D nature. Therefore, understanding the charge transport in layered materials is fundamental to explore the vast opportunities these ultra-thin materials offer. Hence, the challenges targeted in the thesis are: (1) understanding the charge transport in layered materials based on electronic network of quantum and oxide capacitances, (2) studying thickness dependence, ranging from monolayer to bulk, of full range-characteristics of field-effect transistor (FET) based on layered materials, (3) investigating the total interface trap charges to achieve the ultimate subthreshold slope (SS) theoretically possible in FETs, (4) understanding the effect of the channel length on the performance of layered materials, (5) understanding the effect of substrate on performance of the TMDC FETs and studying if the interface of transition metal dichalcogenides (TMDCs)/hexagonalboron nitride (h-BN) can have less enough trap charges to observe ambipolar behavior, (6) Exploring optoelectronic properties in 2D heterostructures that includes understanding graphene/WS2 heterostructure and its optoelectronic applications by creating a p-n junction at the interface. The quality of materials and the interface are the issues for observing and extracting clean physics out of these layered materials and heterostructures. In this dissertation, we realized the use of quantum capacitance in layered materials, substrate effects and carrier transport in heterostructure.

  17. Semi-classical noise investigation for sub-40nm metal-oxide-semiconductor field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Spathis, C., E-mail: cspathis@ece.upatras.gr; Birbas, A.; Georgakopoulou, K. [Department of Electrical and Computer Engineering, University of Patras, Patras 26500 (Greece)

    2015-08-15

    Device white noise levels in short channel Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) dictate the performance and reliability of high-frequency circuits ranging from high-speed microprocessors to Low-Noise Amplifiers (LNAs) and microwave circuits. Recent experimental noise measurements with very short devices demonstrate the existence of suppressed shot noise, contrary to the predictions of classical channel thermal noise models. In this work we show that, as the dimensions continue to shrink, shot noise has to be considered when the channel resistance becomes comparable to the barrier resistance at the source-channel junction. By adopting a semi-classical approach and taking retrospectively into account transport, short-channel and quantum effects, we investigate the partitioning between shot and thermal noise, and formulate a predictive model that describes the noise characteristics of modern devices.

  18. Enhanced performance of GeSn source-pocket tunnel field-effect transistors for low-power applications

    Science.gov (United States)

    Liu, Lei; Liang, Renrong; Wang, Jing; Xu, Jun

    2016-07-01

    Germanium-tin (GeSn) source-pocket tunnel field-effect transistors (TFETs) are comprehensively investigated by numerical device simulations at low supply voltages. Device configurations with homo- and hetero-tunneling junctions (TJ) are analyzed and compared. It is shown that direct-gap GeSn alloys are favorable for increasing the source-pocket tunneling rate. Increasing the source Sn composition of the device may aid the on-state current increase, but the subthreshold swing (SS) is degraded because of the reduced band gap. At ultrascaled supply voltages, the GeSn hetero-TJ TFET with higher pocket Sn composition exhibits the best performance and SS, and the device performance can be further improved by increasing the Sn composition in the pocket region. These simulation results could be used to understand and optimize the performance of GeSn source-pocket TFETs, which are very promising electronic devices for low-power applications.

  19. Study of top and bottom contact resistance in one organic field-effect transistor

    Institute of Scientific and Technical Information of China (English)

    Liu Ge; Liu Ming; Wang Hong; Shang Li-Wei; Ji Zhuo-Yu; Liu Xing-Hua; Liu Jiang

    2009-01-01

    This paper reports that the organic field-effect transistors with hybrid contact geometry were fabricated,in whic hthe top electrodes and the bottom electrodes were combined in parallel resistances within one transistor.With the facility of the novel structure,the difference of contact resistance between the top contact geometry and the bottom contact geometry was studied.The hybrid contact devices showed similar characteristics with the top contact configuration devices,which provide helpful evidence on the lower contact resistance of the top contact configuration device.The origin of the different contact resistance between the top contact device and the bottom contact device was discussed.

  20. High Speed Multiple Valued Logic Full Adder Using Carbon Nano Tube Field Effect Transistor

    CERN Document Server

    Khatir, Ashkan; Mahmoudi, Iman

    2011-01-01

    High speed Full-Adder (FA) module is a critical element in designing high performance arithmetic circuits. In this paper, we propose a new high speed multiple-valued logic FA module. The proposed FA is constructed by 14 transistors and 3 capacitors, using carbon nano-tube field effect transistor (CNFET) technology. Furthermore, our proposed technique has been examined in different voltages (i.e., 0.65v and 0.9v). The observed results reveal power consumption and power delay product (PDP) improvements compared to existing FA counterparts

  1. Light quasiparticles dominate electronic transport in molecular crystal field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Li, Z. Q.; Podzorov, V.; Sai, N.; Martin, Michael C.; Gershenson, M. E.; Di Ventra, M.; Basov, D. N.

    2007-03-01

    We report on an infrared spectroscopy study of mobile holes in the accumulation layer of organic field-effect transistors based on rubrene single crystals. Our data indicate that both transport and infrared properties of these transistors at room temperature are governed by light quasiparticles in molecular orbital bands with the effective masses m[small star, filled]comparable to free electron mass. Furthermore, the m[small star, filled]values inferred from our experiments are in agreement with those determined from band structure calculations. These findings reveal no evidence for prominent polaronic effects, which is at variance with the common beliefs of polaron formation in molecular solids.

  2. High Speed Multiple Valued Logic Full Adder Using Carbon Nano Field Effect Transistor

    Directory of Open Access Journals (Sweden)

    Ashkan Khatir

    2011-03-01

    Full Text Available High speed Full-Adder (FA module is a critical element in designing high performance arithmeticcircuits. In this paper, we propose a new high speed multiple-valued logic FA module. The proposed FAis constructed by 14 transistors and 3 capacitors, using carbon nano-tube field effect transistor (CNFETtechnology. Furthermore, our proposed technique has been examined in different voltages (i.e., 0.65v and0.9v. The observed results reveal power consumption and power delay product (PDP improvementscompared to existing FA counterparts.

  3. Influence of the semiconductor oxidation potential on the operational stability of organic field-effect transistors

    Science.gov (United States)

    Sharma, A.; Mathijssen, S. G. J.; Bobbert, P. A.; de Leeuw, D. M.

    2011-09-01

    During prolonged application of a gate bias, organic field-effect transistors show a gradual shift of the threshold voltage towards the applied gate bias voltage. The shift follows a stretched-exponential time dependence governed by a relaxation time. Here, we show that a thermodynamic analysis reproduces the observed exponential dependence of the relaxation time on the oxidation potential of the semiconductor. The good fit with the experimental data validates the underlying assumptions. It demonstrates that this operational instability is a straightforward thermodynamically driven process that can only be eliminated by eliminating water from the transistor.

  4. Scanning Kelvin probe microscopy on organic field-effect transistors during gate bias stress

    Science.gov (United States)

    Mathijssen, S. G. J.; Cölle, M.; Mank, A. J. G.; Kemerink, M.; Bobbert, P. A.; de Leeuw, D. M.

    2007-05-01

    The reliability of organic field-effect transistors is studied using both transport and scanning Kelvin probe microscopy measurements. A direct correlation between the current and potential of a p-type transistor is demonstrated. During gate bias stress, a decrease in current is observed, that is correlated with the increased curvature of the potential profile. After gate bias stress, the potential changes consistently in all operating regimes: the potential profile gets more convex, in accordance with the simultaneously observed shift in threshold voltage. The changes of the potential are attributed to positive immobile charges, which contribute to the potential, but not to the current.

  5. High-hole-mobility organic-inorganic perovskite field-effect transistors (Conference Presentation)

    Science.gov (United States)

    Matsushima, Toshinori; Hwang, Sun Bin; Sandanayaka, Atula D.; Qin, Chuanjiang; Fujihara, Takashi; Yahiro, Masayuki; Adachi, Chihaya

    2016-11-01

    We have recently focused our attention on the application of perovskite materials to a semiconducting layer in field-effect transistors. Because perovskite materials are expected to promise the processability and flexibility inherent to organic semiconductors as well as the superior carrier transport inherent to inorganic semiconductors, we believe that organic semiconductor-like cost-effective, flexible transistors with inorganic semiconductor-like high carrier mobility can be realized using perovskite semiconductors in future. In this study, we have prepared the tin iodide-based perovskite as a semiconducting layer on silicon dioxide layers treated with a self-assembled monolayer containing ammonium iodide terminal groups by spin coating and, then, source-drain electrodes on the perovskite layer by vacuum deposition for the fabrication of a top-contact perovskite transistor. Because of a well-developed perovskite layer formed on the treated substrate and reduced contact resistance resulting from the top-contact structure, we have obtained a new record hole mobility of up to 12 cm2 V-1 s-1 in our perovskite transistors, which is about five times higher than a previous record hole mobility and is considered to be a very good value when compared with widely investigated organic transistors. Along with the high hole mobility, we have demonstrated that this surface treatment leads to smaller hysteresis in output and transfer characteristics and better stress stability under constant gate voltage application. These findings open the way for huge advances in solution-processable high-mobility transistors.

  6. Silicon nanotube field effect transistor with core-shell gate stacks for enhanced high-performance operation and area scaling benefits

    KAUST Repository

    Fahad, Hossain M.

    2011-10-12

    We introduce the concept of a silicon nanotube field effect transistor whose unique core-shell gate stacks help achieve full volume inversion by giving a surge in minority carrier concentration in the near vicinity of the ultrathin channel and at the same time rapid roll-off at the source and drain junctions constituting velocity saturation-induced higher drive current-enhanced high performance per device with efficient real estate consumption. The core-shell gate stacks also provide superior short channel effects control than classical planar metal oxide semiconductor field effect transistor (MOSFET) and gate-all-around nanowire FET. The proposed device offers the true potential to be an ideal blend for quantum ballistic transport study of device property control by bottom-up approach and high-density integration compatibility using top-down state-of-the-art complementary metal oxide semiconductor flow. © 2011 American Chemical Society.

  7. Unidirectional coating technology for organic field-effect transistors: materials and methods

    Science.gov (United States)

    Sun, Huabin; Wang, Qijing; Qian, Jun; Yin, Yao; Shi, Yi; Li, Yun

    2015-05-01

    Solution-processed organic field-effect transistors (OFETs) are essential for developing organic electronics. The encouraging development in solution-processed OFETs has attracted research interest because of their potential in low-cost devices with performance comparable to polycrystalline-silicon-based transistors. In recent years, unidirectional coating technology, featuring thin-film coating along only one direction and involving specific materials as well as solution-assisted fabrication methods, has attracted intensive interest. Transistors with organic semiconductor layers, which are deposited via unidirectional coating methods, have achieved high performance. In particular, carrier mobility has been greatly enhanced to values much higher than 10 cm2 V-1 s-1. Such significant improvement is mainly attributed to better control in morphology and molecular packing arrangement of organic thin film. In this review, typical materials that are being used in OFETs are discussed, and demonstrations of unidirectional coating methods are surveyed.

  8. Preparation and characteristics of flexible all-organic thin-film field-effect transistor

    Institute of Scientific and Technical Information of China (English)

    QIU Yong; HU Yuanchuan; Dong Guifang; WANG Liduo; Xie Junfeng; MA Yaning

    2003-01-01

    All-organic thin-film field-effect transistor was prepared on flexible poly(ethylene-terephthalate) (PET) substrate. Poly(methyl-methacrylate) (PMMA) and pentacene are used as a dielectric layer and a semiconductor layer, respectively. The hole mobility of the transistor can reach 2.10×10-2 cm2/Vs, and the on/off current ratio was larger than 105. The performances of the transistor, when the substrate is cured under different radius, were also measured. It was found that the device performance did not change when the curly direction was vertical to the channel length direction and when the curly direction was parallel to the channel length direction with 3.67 cm curvature radius, the mobility of the device increased by more than 20% and the on/off ratio decreased more than one order.

  9. High Performance Polymer Field-Effect Transistors Based on Thermally Crosslinked Poly(3-hexylthiophene)

    Institute of Scientific and Technical Information of China (English)

    JIANG Chun-Xi; YANG Xiao-Yan; ZHAO Kai; WU Xiao-Ming; YANG Li-Ying; CHENG Xiao-Man; WEI Jun; YIN Shou-Gen

    2011-01-01

    The performance of polymer field-effect transistors is improved by thermal crosslinking of poly(3-hexylthiophene), using ditert butyl peroxide as the crosslinker. The device performance depends on the crosslinker concentration significantly. We obtain an optimal on/off ratio of 105 and the saturate field-effect mobility of 0.34cm2V-1s-1, by using a suitable ratios of ditert butyl peroxide, 0.5 wt% of poly(3-hexylthiophene). The microstructure images show that the crosslinked poly(3-hexylthiophene) active layers simultaneously possess appropriate crystallinity and smooth morphology. Moreover, crosslinking of poly(3-hexylthiophene) prevents the transistors from large threshold voltage shifts under ambient bias-stressing, showing an advantage in encouraging device environmental and operating stability.%The performance of polymer field-effect transistors is improved by thermal crosslinking of poly(3-hexylthiophene),using ditert butyl peroxide as the crosslinker.The device performance depends on the crosslinker concentration significantly.We obtain an optimal on/off ratio of 105 and the saturate field-effect mobility of 0.34 cm2 V-1s-1,by using a suitable ratios of ditert butyl peroxide,0.5 wt% of poly(3-hexylthiophene).The microstructure images show that the crosslinked poly(3-hexylthiophene) active layers simultaneously possess appropriate crystallinity and smooth morphology.Moreover,crosslinking of poly(3-hexylthiophene) prevents the transistors from large threshold voltage shifts under ambient bias-stressing,showing an advantage in encouraging device environmental and operating stability.Polymer field-effect transistors have received great academic and industrial interests since they were initially demonstrated,[1] due to their considerable advantages as low/room-temperature fabrication,large-area patterning and low-cost solutionprocessability combining with excellent flexibility.[2-5]However,such devices generally suffer from low charge carrier mobility (usually

  10. Direct Electrical Detection of DNA Hybridization Based on Electrolyte-Gated Graphene Field-Effect Transistor

    Science.gov (United States)

    Ohno, Yasuhide; Okamoto, Shogo; Maehashi, Kenzo; Matsumoto, Kazuhiko

    2013-11-01

    DNA hybridization was electrically detected by graphene field-effect transistors. Probe DNA was modified on the graphene channel by a pyrene-based linker material. The transfer characteristic was shifted by the negative charges on the probe DNA, and the drain current was changed by the full-complementary DNA while no current change was observed after adding noncomplementary DNA, indicating that the graphene field-effect transistor detected the DNA hybridization. In addition, the number of DNAs was estimated by the simple plate capacitor model. As a result, one probe DNA was attached on the graphene channel per 10×10 nm2, indicating their high density functionalization. We estimated that 30% of probe DNA on the graphene channel was hybridized with 200 nM full-complementary DNA while only 5% of probe DNA was bound to the noncomplementary DNA. These results will help to pave the way for future biosensing applications based on graphene FETs.

  11. Metal nanoparticles in organic field-effect transistor: Transition from charge trapping to conduction mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Keanchuan, E-mail: lee.kc@petronas.com.my [Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8552 (Japan); Weis, Martin [Institute of Electronics and Photonics, Slovak University of Technology, Ilkovičova 3, Bratislava 81219 (Slovakia); Chen, Xiangyu; Taguchi, Dai; Manaka, Takaaki [Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8552 (Japan); Iwamoto, Mitsumasa, E-mail: iwamoto@pe.titech.ac.jp [Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8552 (Japan)

    2014-03-03

    Self-assembled monolayers of metal nanoparticles (NPs) are envisioned for various devices and have been investigated for possible applications. However, organic envelope of NPs which is required for self-assembling must be often removed prior further device fabrication. Here, we report on effect of ozonolysis on monolayer of silver NPs (Ag NPs) with size of 8 nm and its impact on Ag NPs utilization in organic field-effect transistor. It was found that Ag NPs covered by organics serve like a traps and removal of insulating organics decreases number of traps and consequently increases Ag NPs monolayer conductivity. - Highlights: • Organic field-effect transistor (OFET) with nanoparticle (NP) film was fabricated • Electrical and optical properties of NP and OFET were studied upon UV irradiation • We report a transition from charge trapping to conduction mechanism of NPs in OFET.

  12. Transport properties of hydrogen passivated silicon nanotubes and silicon nanotube field effect transistors

    KAUST Repository

    Montes Muñoz, Enrique

    2017-01-24

    We investigate the electronic transport properties of silicon nanotubes attached to metallic electrodes from first principles, using density functional theory and the non-equilibrium Green\\'s function method. The influence of the surface termination is studied as well as the dependence of the transport characteristics on the chirality, diameter, and length. Strong electronic coupling between nanotubes and electrodes is found to be a general feature that results in low contact resistance. The conductance in the tunneling regime is discussed in terms of the complex band structure. Silicon nanotube field effect transistors are simulated by applying a uniform potential gate. Our results demonstrate very high values of transconductance, outperforming the best commercial silicon field effect transistors, combined with low values of sub-threshold swing.

  13. Towards a cleaner graphene surface in graphene field effect transistor via N,N-Dimethylacetamide

    Science.gov (United States)

    Mao, Da-Cheng; Peng, Song-Ang; Wang, Shao-Qing; Zhang, Da-Yong; Shi, Jing-Yuan; Wang, Xinnan; Jin, Zhi

    2016-09-01

    Graphene is a two-dimensional material with a high surface to volume ratio and the fabrication process of graphene field effect transistors always introduces unintended contaminates like photoresidues on the surface of graphene. These contaminations are difficult to remove by conventional acetone solvent and suppress the intrinsic properties of graphene. To address the problem, a wet-chemical approach employing N,N-Dimethylacetamide (C4H9NO) was developed in this study, which shows an increase of the carrier mobility and a reduction of minimum conductance point in our devices. Raman spectroscopy and atomic force microscope were carried out to verify the cleaning effect of the approach. Our method provides a simple and effective way to enhance the electrical performance of graphene field effect transistors and can be readily integrated into the CMOS fabrication pilot line.

  14. Diketopyrrolopyrrole-diketopyrrolopyrrole-based conjugated copolymer for high-mobility organic field-effect transistors

    KAUST Repository

    Kanimozhi, Catherine K.

    2012-10-10

    In this communication, we report the synthesis of a novel diketopyrrolopyrrole-diketopyrrolopyrrole (DPP-DPP)-based conjugated copolymer and its application in high-mobility organic field-effect transistors. Copolymerization of DPP with DPP yields a copolymer with exceptional properties such as extended absorption characteristics (up to ∼1100 nm) and field-effect electron mobility values of >1 cm 2 V -1 s -1. The synthesis of this novel DPP-DPP copolymer in combination with the demonstration of transistors with extremely high electron mobility makes this work an important step toward a new family of DPP-DPP copolymers for application in the general area of organic optoelectronics. © 2012 American Chemical Society.

  15. Steep switching characteristics of single-gated feedback field-effect transistors

    Science.gov (United States)

    Kim, Minsuk; Kim, Yoonjoong; Lim, Doohyeok; Woo, Sola; Cho, Kyoungah; Kim, Sangsig

    2017-02-01

    In this study, we propose newly designed feedback field-effect transistors that utilize the positive feedback of charge carriers in single-gated silicon channels to achieve steep switching behaviors. The band diagram, I-V characteristics, subthreshold swing, and on/off current ratio are analyzed using a commercial device simulator. Our proposed feedback field-effect transistors exhibit subthreshold swings of less than 0.1 mV dec-1, an on/off current ratio of approximately 1011, and an on-current of approximately 10-4 A at room temperature, demonstrating that the switching characteristics are superior to those of other silicon-based devices. In addition, the device parameters that affect the device performance, hysteresis characteristics, and temperature-dependent device characteristics are discussed in detail.

  16. Single-Walled Carbon Nanotube Network Field Effect Transistor as a Humidity Sensor

    Directory of Open Access Journals (Sweden)

    Prasantha R. Mudimela

    2012-01-01

    Full Text Available Single-walled carbon nanotube network field effect transistors were fabricated and studied as humidity sensors. Sensing responses were altered by changing the gate voltage. At the open channel state (negative gate voltage, humidity pulse resulted in the decrease of the source-drain current, and, vice versa, the increase in the source-drain current was observed at the positive gate voltage. This effect was explained by the electron-donating nature of water molecules. The operation speed and signal intensity was found to be dependent on the gate voltage polarity. The positive or negative change in current with humidity pulse at zero-gate voltage was found to depend on the previous state of the gate electrode (positive or negative voltage, respectively. Those characteristics were explained by the charge traps in the gate dielectric altering the effective gate voltage, which influenced the operation of field effect transistor.

  17. Multifunctional Self-Assembled Monolayers for Organic Field-Effect Transistors

    Science.gov (United States)

    Cernetic, Nathan

    Organic field effect transistors (OFETs) have the potential to reach commercialization for a wide variety of applications such as active matrix display circuitry, chemical and biological sensing, radio-frequency identification devices and flexible electronics. In order to be commercially competitive with already at-market amorphous silicon devices, OFETs need to approach similar performance levels. Significant progress has been made in developing high performance organic semiconductors and dielectric materials. Additionally, a common route to improve the performance metric of OFETs is via interface modification at the critical dielectric/semiconductor and electrode/semiconductor interface which often play a significant role in charge transport properties. These metal oxide interfaces are typically modified with rationally designed multifunctional self-assembled monolayers. As means toward improving the performance metrics of OFETs, rationally designed multifunctional self-assembled monolayers are used to explore the relationship between surface energy, SAM order, and SAM dipole on OFET performance. The studies presented within are (1) development of a multifunctional SAM capable of simultaneously modifying dielectric and metal surface while maintaining compatibility with solution processed techniques (2) exploration of the relationship between SAM dipole and anchor group on graphene transistors, and (3) development of self-assembled monolayer field-effect transistor in which the traditional thick organic semiconductor is replaced by a rationally designed self-assembled monolayer semiconductor. The findings presented within represent advancement in the understanding of the influence of self-assembled monolayers on OFETs as well as progress towards rationally designed monolayer transistors.

  18. High mobility graphene ion-sensitive field-effect transistors by noncovalent functionalization

    Science.gov (United States)

    Fu, W.; Nef, C.; Tarasov, A.; Wipf, M.; Stoop, R.; Knopfmacher, O.; Weiss, M.; Calame, M.; Schönenberger, C.

    2013-11-01

    Noncovalent functionalization is a well-known nondestructive process for property engineering of carbon nanostructures, including carbon nanotubes and graphene. However, it is not clear to what extend the extraordinary electrical properties of these carbon materials can be preserved during the process. Here, we demonstrated that noncovalent functionalization can indeed delivery graphene field-effect transistors (FET) with fully preserved mobility. In addition, these high-mobility graphene transistors can serve as a promising platform for biochemical sensing applications.Noncovalent functionalization is a well-known nondestructive process for property engineering of carbon nanostructures, including carbon nanotubes and graphene. However, it is not clear to what extend the extraordinary electrical properties of these carbon materials can be preserved during the process. Here, we demonstrated that noncovalent functionalization can indeed delivery graphene field-effect transistors (FET) with fully preserved mobility. In addition, these high-mobility graphene transistors can serve as a promising platform for biochemical sensing applications. Electronic supplementary information (ESI) available. See DOI: 10.1039/c3nr03940d

  19. Sensing small neurotransmitter-enzyme interaction with nanoporous gated ion-sensitive field effect transistors.

    Science.gov (United States)

    Kisner, Alexandre; Stockmann, Regina; Jansen, Michael; Yegin, Ugur; Offenhäusser, Andreas; Kubota, Lauro Tatsuo; Mourzina, Yulia

    2012-01-15

    Ion-sensitive field effect transistors with gates having a high density of nanopores were fabricated and employed to sense the neurotransmitter dopamine with high selectivity and detectability at micromolar range. The nanoporous structure of the gates was produced by applying a relatively simple anodizing process, which yielded a porous alumina layer with pores exhibiting a mean diameter ranging from 20 to 35 nm. Gate-source voltages of the transistors demonstrated a pH-dependence that was linear over a wide range and could be understood as changes in surface charges during protonation and deprotonation. The large surface area provided by the pores allowed the physical immobilization of tyrosinase, which is an enzyme that oxidizes dopamine, on the gates of the transistors, and thus, changes the acid-base behavior on their surfaces. Concentration-dependent dopamine interacting with immobilized tyrosinase showed a linear dependence into a physiological range of interest for dopamine concentration in the changes of gate-source voltages. In comparison with previous approaches, a response time relatively fast for detecting dopamine was obtained. Additionally, selectivity assays for other neurotransmitters that are abundantly found in the brain were examined. These results demonstrate that the nanoporous structure of ion-sensitive field effect transistors can easily be used to immobilize specific enzyme that can readily and selectively detect small neurotransmitter molecule based on its acid-base interaction with the receptor. Therefore, it could serve as a technology platform for molecular studies of neurotransmitter-enzyme binding and drugs screening.

  20. Graphene-based field effect transistors for radiation-induced field sensing

    Energy Technology Data Exchange (ETDEWEB)

    Di Gaspare, Alessandra, E-mail: alessandra.digaspare@lnf.infn.it [INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); Valletta, Antonio [CNR-Istituto per la Microelettronica e i Microsistemi, TorVergata, Rome (Italy); Fortunato, Guglielmo [CNR-Istituto per la Microelettronica e i Microsistemi, TorVergata, Rome (Italy); INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); Larciprete, Rosanna [CNR-Istituto di Sistemi Complessi, TorVergata, Rome (Italy); INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); Mariucci, Luigi [CNR-Istituto per la Microelettronica e i Microsistemi, TorVergata, Rome (Italy); INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); Notargiacomo, Andrea [CNR-Istituto di Fotonica e Nanotecnologie, Rome (Italy); INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); Cimino, Roberto [INFN-Laboratori Nazionali Frascati, Frascati, Rome (Italy); CERN, Geneva (Switzerland)

    2016-07-11

    We propose the implementation of graphene-based field effect transistor (FET) as radiation sensor. In the proposed detector, graphene obtained via chemical vapor deposition is integrated into a Si-based field effect device as the gate readout electrode, able to sense any change in the field distribution induced by ionization in the underneath absorber, because of the strong variation in the graphene conductivity close to the charge neutrality point. Different 2-dimensional layered materials can be envisaged in this kind of device.

  1. The design and synthesis of fused thiophenes and their applications in organic field-effect transistors

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Fused thiophenes refer to oligothienoacenes in which several thiophenes are coupled together via twoor multi-positions and their derivatives. The synthesized organic semiconductors based on fused thiophenes exhibit excellent field effect properties due to their efficient intermolecular S…S interactions and π…π stacking. The performances of organic field-effect transistors (OFETs) depend not only on the materials but also on the devices. Such factors which influence the device performances as device structures, fabrication technologies and interface engineering are extensively investigated based on the fused thiophenes. Searching for new organic semiconductors and improving the device fabrication technologies are two major issues in the development of OFETs.

  2. Organic single crystals or crystalline micro/nanostructures: Preparation and field-effect transistor applications

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Organic single crystals hold great promise for the development of organic semiconductor materials,because they could reveal the intrinsic electronic properties of these materials,providing high-performance electronic devices and probing the structureproperty relationships.This article reviews the preparation methods for organic single crystals or crystalline micro/nanostructures,including vapor phase growth methods and solution-processed methods,and summarizes a few methods employed in the fabrication of field-effect transistors along with dozens of examples concerning both small molecules and polymers with high field-effect performance.

  3. Bisacenaphthopyrazinoquinoxaline derivatives: Synthesis, physical properties and applications as semiconductors for n-channel field effect transistors

    KAUST Repository

    Tong, Chenhua

    2013-01-01

    Several bisacenaphthopyrazinoquinoxaline (BAPQ) based derivatives 1-3 were synthesized by condensation between the acenaphthenequinones and 1,2,4,5-tetraaminobenzene tetrahydrochloride. Their optical, electrochemical and self-assembling properties are tuned by different substituents. Among them, compound 3 possesses a homogeneously distributed low-lying LUMO due to the peripheral substitution with four cyano groups. The corresponding n-channel field effect transistors showed a field effect electron mobility of 5 × 10-3 cm2 V-1 s-1. © 2013 The Royal Society of Chemistry.

  4. Organic field-effect transistor circuits with electrode interconnections using reverse stamping

    Science.gov (United States)

    Choi, Sangmoo; Fuentes-Hernandez, Canek; Yun, Minseong; Dindar, Amir; Khan, Talha M.; Wang, Cheng-Yin; Kippelen, Bernard

    2014-10-01

    We discuss a non-vacuum low-cost reverse stamping method for the realization of circuits based on top-gate organic field-effect transistors (OFETs) with a bi-layer gate dielectric. This method allows for patterning of high-k inorganic dielectric films produced by atomic layer deposition and consequently of the bilayer gate dielectric layers used in our top-gate OFETs. We demonstrate the fabrication and operation of logic inverters and ring oscillators following this approach.

  5. Electrolyte gate dependent high-frequency measurement of graphene field-effect transistor for sensing applications

    OpenAIRE

    Fu, W.; El Abbassi, M.; Hasler, T.; M. Jung; M. Steinacher; Calame, M.; Schönenberger,C.; Puebla-Hellmann, G.; Hellmüller, S.; T. Ihn; Wallraff, A.

    2014-01-01

    We performed radiofrequency (RF) reflectometry measurements at 2.4 GHz on electrolyte-gated graphene field-effect transistors (GFETs) utilizing a tunable stub-matching circuit for impedance matching. We demonstrate that the gate voltage dependent RF resistivity of graphene can be deduced even in the presence of the electrolyte which is in direct contact with the graphene layer. The RF resistivity is found to be consistent with its DC counterpart in the full gate voltage range. Furthermore, in...

  6. Current steering detection scheme of three terminal antenna-coupled terahertz field effect transistor detectors

    OpenAIRE

    Földesy, Péter

    2013-01-01

    An antenna-coupled field effect transistor (FET) as a plasma wave terahertz detector is used with the current steering to record separately the gate-source and gate-drain photoresponses and their phase sensitive combination. This method is based on the observation that the plasmon-terminal coupling is cut off in saturation, resulting in only one-sided sensitivity. A polarimetric example is presented with intensity and polarization angle reconstruction using a single three-terminal antenna-cou...

  7. Ion-sensitive field effect transistors using carbon nanotubes as the transducing layer.

    Science.gov (United States)

    Cid, Cristina C; Riu, Jordi; Maroto, Alicia; Rius, F Xavier

    2008-08-01

    We report a new type of ion-sensitive field effect transistor (ISFET). This type of ISFET incorporates a new architecture, containing a network of single-walled carbon nanotubes (SWCNTs) as the transduction layer, making an external reference electrode unnecessary. To show an example of its application, the SWCNT-based ISFET is able to detect at least 10(-8) M of potassium in water using an ion-selective membrane containing valinomycin.

  8. Ultrathin MXene-Micropattern-Based Field-Effect Transistor for Probing Neural Activity.

    Science.gov (United States)

    Xu, Bingzhe; Zhu, Minshen; Zhang, Wencong; Zhen, Xu; Pei, Zengxia; Xue, Qi; Zhi, Chunyi; Shi, Peng

    2016-05-01

    A field-effect transistor (FET) based on ultrathin Ti3 C2 -MXene micropatterns is developed and utilized as a highly sensitive biosensor. The device is produced with the microcontact printing technique, making use of its unique advantages for easy fabrication. Using the MXene-FET device, label-free probing of small molecules in typical biological environments and fast detection of action potentials in primary neurons is demonstrated.

  9. Novel three-state quantum dot gate field effect transistor fabrication, modeling and applications

    CERN Document Server

    Karmakar, Supriya

    2014-01-01

    The book presents the fabrication and circuit modeling of quantum dot gate field effect transistor (QDGFET) and quantum dot gate NMOS inverter (QDNMOS inverter). It also introduces the development of a circuit model of QDGFET based on Berkley Short Channel IGFET model (BSIM). Different ternary logic circuits based on QDGFET are also investigated in this book. Advanced circuit such as three-bit and six bit analog-to-digital converter (ADC) and digital-to-analog converter (DAC) were also simulated.

  10. Frequency kesponse of top-gated carbon nanotube field-effect transistors

    OpenAIRE

    Singh, Dinkar V.; Jenkins, Keith A.; Appenzeller, Joerg; Neumayer, D.; Grill, Alfred; Wong, H. S. Philip

    2004-01-01

    The ac performance of carbon nanotube field-effect transistors (CNFETs) has been characterized using two approaches involving: 1) time- and 2) frequency-domain measurements. A high input impedance measurement system was used to demonstrate time-domain switching of CNFETs at frequencies up to 100 kHz. The low level of signal crosstalk in CNFETs fabricated on quartz substrates enabled frequency-domain measurements of the ac response of CNFETs in the megahertz range, over five orders of magnitud...

  11. Incorporating TCNQ into thiophene-fused heptacene for n-channel field effect transistor

    KAUST Repository

    Ye, Qun

    2012-06-01

    Incorporation of electron-deficient tetracyanoquinodimethane (TCNQ) into electron-rich thiophene-fused heptacene was successfully achieved for the purpose of stabilizing longer acenes and generating new n-type organic semiconductors. The heptacene-TCNQ derivative 1 was found to have good stability and an expected electron transporting property. Electron mobility up to 0.01 cm 2 V -1 s -1 has been obtained for this novel material in solution processed organic field effect transistors. © 2012 American Chemical Society.

  12. Atomic-Monolayer MoS2 Band-to-Band Tunneling Field-Effect Transistor

    KAUST Repository

    Lan, Yann Wen

    2016-09-05

    The experimental observation of band-to-band tunneling in novel tunneling field-effect transistors utilizing a monolayer of MoS2 as the conducting channel is demonstrated. Our results indicate that the strong gate-coupling efficiency enabled by two-dimensional materials, such as monolayer MoS2, results in the direct manifestation of a band-to-band tunneling current and an ambipolar transport.

  13. THz Plasma Waves in Field-Effect-Transistors: A Monte Carlo Study

    OpenAIRE

    Schumann, Steffen

    2015-01-01

    Sensing with electromagnetic waves having frequencies in the Terahertz-range is a very attractive investigative method with applications in fundamental research and industrial settings. Up to now, a lot of sources and detectors are available. However, most of these systems are bulky and have to be used in controllable environments such as laboratories. In 1993 Dyakonov and Shur suggested that plasma waves developing in field-effect-transistors can be used to emit and detect THz-radiation. Lat...

  14. Towards the textile transistor: Assembly and characterization of an organic field effect transistor with a cylindrical geometry

    Science.gov (United States)

    Maccioni, Maurizio; Orgiu, Emanuele; Cosseddu, Piero; Locci, Simone; Bonfiglio, Annalisa

    2006-10-01

    Cylindrical organic field effect transistors have been obtained starting from a metallic fiber used in textile processes. The metal core of the yarn, covered with a thin polyimide layer, is the gate of the structure. A top-contact device can be obtained by depositing a layer of organic semiconductor followed by the deposition of source and drain top contacts, made by metals or conductive polymers, deposited by evaporation or soft lithography. Thanks to the flexibility of the structure and the low cost of technologies, this device is a meaningful step towards innovative applications of textile electronics.

  15. Device perspective for black phosphorus field-effect transistors: contact resistance, ambipolar behavior, and scaling.

    Science.gov (United States)

    Du, Yuchen; Liu, Han; Deng, Yexin; Ye, Peide D

    2014-10-28

    Although monolayer black phosphorus (BP), or phosphorene, has been successfully exfoliated and its optical properties have been explored, most of the electrical performance of the devices is demonstrated on few-layer phosphorene and ultrathin BP films. In this paper, we study the channel length scaling of ultrathin BP field-effect transistors (FETs) and discuss a scheme for using various contact metals to change the transistor characteristics. Through studying transistor behaviors with various channel lengths, the contact resistance can be extracted with the transfer length method (TLM). With different contact metals, we find out that the metal/BP interface has different Schottky barrier heights, leading to a significant difference in contact resistance, which is quite different from previous studies of transition metal dichalcogenides (TMDs), such as MoS2, where the Fermi level is strongly pinned near the conduction band edge at the metal/MoS2 interface. The nature of BP transistors is Schottky barrier FETs, where the on and off states are controlled by tuning the Schottky barriers at the two contacts. We also observe the ambipolar characteristics of BP transistors with enhanced n-type drain current and demonstrate that the p-type carriers can be easily shifted to n-type or vice versa by controlling the gate bias and drain bias, showing the potential to realize BP CMOS logic circuits.

  16. Measurement and Analysis of a Ferroelectric Field-Effect Transistor NAND Gate

    Science.gov (United States)

    Phillips, Thomas A.; MacLeond, Todd C.; Sayyah, Rana; Ho, Fat Duen

    2009-01-01

    Previous research investigated expanding the use of Ferroelectric Field-Effect Transistors (FFET) to other electronic devices beyond memory circuits. Ferroelectric based transistors possess unique characteris tics that give them interesting and useful properties in digital logic circuits. The NAND gate was chosen for investigation as it is one of the fundamental building blocks of digital electronic circuits. In t his paper, NAND gate circuits were constructed utilizing individual F FETs. N-channel FFETs with positive polarization were used for the standard CMOS NAND gate n-channel transistors and n-channel FFETs with n egative polarization were used for the standard CMOS NAND gate p-chan nel transistors. The voltage transfer curves were obtained for the NA ND gate. Comparisons were made between the actual device data and the previous modeled data. These results are compared to standard MOS logic circuits. The circuits analyzed are not intended to be fully opera tional circuits that would interface with existing logic circuits, bu t as a research tool to look into the possibility of using ferroelectric transistors in future logic circuits. Possible applications for th ese devices are presented, and their potential benefits and drawbacks are discussed.

  17. Novel field-effect schottky barrier transistors based on graphene-MoS 2 heterojunctions

    KAUST Repository

    Tian, He

    2014-08-11

    Recently, two-dimensional materials such as molybdenum disulphide (MoS 2) have been demonstrated to realize field effect transistors (FET) with a large current on-off ratio. However, the carrier mobility in backgate MoS2 FET is rather low (typically 0.5-20 cm2/V.s). Here, we report a novel field-effect Schottky barrier transistors (FESBT) based on graphene-MoS2 heterojunction (GMH), where the characteristics of high mobility from graphene and high on-off ratio from MoS2 are properly balanced in the novel transistors. Large modulation on the device current (on/off ratio of 105) is achieved by adjusting the backgate (through 300 nm SiO2) voltage to modulate the graphene-MoS2 Schottky barrier. Moreover, the field effective mobility of the FESBT is up to 58.7 cm2/V.s. Our theoretical analysis shows that if the thickness of oxide is further reduced, a subthreshold swing (SS) of 40 mV/decade can be maintained within three orders of drain current at room temperature. This provides an opportunity to overcome the limitation of 60 mV/decade for conventional CMOS devices. The FESBT implemented with a high on-off ratio, a relatively high mobility and a low subthreshold promises low-voltage and low-power applications for future electronics.

  18. Fabrication of graphene field-effect transistor on top of ferroelectric single-crystal substrate

    Science.gov (United States)

    Park, Nahee; Kang, Haeyong; Lee, Yourack; Kim, Jeong-Gyun; Kim, Joong-Gyu; Yun, Yoojoo; Park, Jeongmin; Kim, Taesoo; Kim, Jung Ho; Jin, Youngjo; Shin, Yong Seon; Lee, Young Hee; Suh, Dongseok

    2015-03-01

    In the analysis of Graphene field-effect transistor, the substrate material which has the direct contact with Graphene layer plays an important in the device performance. In this presentation, we have tested PMN-PT(i.e.(1-x)Pb(Mg1/3Nb2/3) O3-xPbTiO3) substrate as a gate dielectric of Graphene field-effect transistor. Unlike the case of previously used substrates such as silicon oxide or hexagonal Boron-Nitride(h-BN), the PMN-PT substrate can induce giant amount of surface charge that is directly injected to the attached Graphene layer due to its ferroelectric property. And the hysteresis of polarization versus electric field of PMN-PT can cause the device to show the ferroelectric nonvolatile memory operation. We had successfully fabricated Graphene field-effect transistor using the mechanically exfoliated Graphene layer transferred on the PMN-PT(001) substrate. Unlike the case of mechanical exfoliation on the surface of silicon-oxide or the Poly(methyl methacrylate) (PMMA), the weak adhesion properties between graphene and PMNPT required the pretreatment on PMMA before the exfoliation process. The device performance is analyzed in terms of the effect of ferro- and piezo-electric effect of PMNPT substrate.

  19. Transistors

    CERN Document Server

    Kendall, E J M

    2013-01-01

    Transistors covers the main thread of transistor development. This book is organized into 2 parts encompassing 19, and starts with an overview of the semi-conductor physics pertinent to the understanding of transistors, as well as features and applications of the point contact devices and junction devices. The subsequent part deals with the modulation of conductance of thin films of conductors by surface charges, the metal-semi conductor, and the semi-conductor triode. These topics are followed by discussions on the nature of the forward current, physical principles in transistor, the hole inj

  20. Nature of size effects in compact models of field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Torkhov, N. A., E-mail: trkf@mail.ru [Tomsk State University, Tomsk 634050 (Russian Federation); Scientific-Research Institute of Semiconductor Devices, Tomsk 634050 (Russian Federation); Tomsk State University of Control Systems and Radioelectronics, Tomsk 634050 (Russian Federation); Babak, L. I.; Kokolov, A. A.; Salnikov, A. S.; Dobush, I. M. [Tomsk State University of Control Systems and Radioelectronics, Tomsk 634050 (Russian Federation); Novikov, V. A., E-mail: novikovvadim@mail.ru; Ivonin, I. V. [Tomsk State University, Tomsk 634050 (Russian Federation)

    2016-03-07

    Investigations have shown that in the local approximation (for sizes L < 100 μm), AlGaN/GaN high electron mobility transistor (HEMT) structures satisfy to all properties of chaotic systems and can be described in the language of fractal geometry of fractional dimensions. For such objects, values of their electrophysical characteristics depend on the linear sizes of the examined regions, which explain the presence of the so-called size effects—dependences of the electrophysical and instrumental characteristics on the linear sizes of the active elements of semiconductor devices. In the present work, a relationship has been established for the linear model parameters of the equivalent circuit elements of internal transistors with fractal geometry of the heteroepitaxial structure manifested through a dependence of its relative electrophysical characteristics on the linear sizes of the examined surface areas. For the HEMTs, this implies dependences of their relative static (A/mm, mA/V/mm, Ω/mm, etc.) and microwave characteristics (W/mm) on the width d of the sink-source channel and on the number of sections n that leads to a nonlinear dependence of the retrieved parameter values of equivalent circuit elements of linear internal transistor models on n and d. Thus, it has been demonstrated that the size effects in semiconductors determined by the fractal geometry must be taken into account when investigating the properties of semiconductor objects on the levels less than the local approximation limit and designing and manufacturing field effect transistors. In general, the suggested approach allows a complex of problems to be solved on designing, optimizing, and retrieving the parameters of equivalent circuits of linear and nonlinear models of not only field effect transistors but also any arbitrary semiconductor devices with nonlinear instrumental characteristics.

  1. Nature of size effects in compact models of field effect transistors

    Science.gov (United States)

    Torkhov, N. A.; Babak, L. I.; Kokolov, A. A.; Salnikov, A. S.; Dobush, I. M.; Novikov, V. A.; Ivonin, I. V.

    2016-03-01

    Investigations have shown that in the local approximation (for sizes L GaN high electron mobility transistor (HEMT) structures satisfy to all properties of chaotic systems and can be described in the language of fractal geometry of fractional dimensions. For such objects, values of their electrophysical characteristics depend on the linear sizes of the examined regions, which explain the presence of the so-called size effects—dependences of the electrophysical and instrumental characteristics on the linear sizes of the active elements of semiconductor devices. In the present work, a relationship has been established for the linear model parameters of the equivalent circuit elements of internal transistors with fractal geometry of the heteroepitaxial structure manifested through a dependence of its relative electrophysical characteristics on the linear sizes of the examined surface areas. For the HEMTs, this implies dependences of their relative static (A/mm, mA/V/mm, Ω/mm, etc.) and microwave characteristics (W/mm) on the width d of the sink-source channel and on the number of sections n that leads to a nonlinear dependence of the retrieved parameter values of equivalent circuit elements of linear internal transistor models on n and d. Thus, it has been demonstrated that the size effects in semiconductors determined by the fractal geometry must be taken into account when investigating the properties of semiconductor objects on the levels less than the local approximation limit and designing and manufacturing field effect transistors. In general, the suggested approach allows a complex of problems to be solved on designing, optimizing, and retrieving the parameters of equivalent circuits of linear and nonlinear models of not only field effect transistors but also any arbitrary semiconductor devices with nonlinear instrumental characteristics.

  2. PH MEASUREMENTS WITH AN ION SENSITIVE FIELD-EFFECT TRANSISTOR IN THE MOUTH OF PATIENTS WITH XEROSTOMIA

    NARCIS (Netherlands)

    VISCH, LL; BERGVELD, P; LAMPRECHT, W; SGRAVENMADE, EJ

    A transistor pH electrode (ion sensitive field effect transistor), placed in the upper dentures of eleven xerostomia patients and five healthy volunteers, was used to register pH changes in five-, six- and seven-day-old dental plaque. A mouth rinse with a 10% sucrose solution caused a pH fall of

  3. Probing Out-of-Plane Charge Transport in Black Phosphorus with Graphene-Contacted Vertical Field-Effect Transistors

    OpenAIRE

    Kang, Junmo; Jariwala, Deep; Ryder, Christopher R.; Wells, Spencer A.; Choi, Yongsuk; Hwang, Euyheon; Cho, Jeong Ho; Marks, Tobin J.; Hersam, Mark C.

    2016-01-01

    Black phosphorus (BP) has recently emerged as a promising narrow band gap layered semiconductor with optoelectronic properties that bridge the gap between semi-metallic graphene and wide band gap transition metal dichalcogenides such as MoS2. To date, BP field-effect transistors have utilized a lateral geometry with in-plane transport dominating device characteristics. In contrast, we present here a vertical field-effect transistor geometry based on a graphene/BP van der Waals heterostructure...

  4. Device and circuit level performance analysis of novel InAs/Si heterojunction double gate tunnel field effect transistor

    Science.gov (United States)

    Ahish, S.; Sharma, Dheeraj; Vasantha, M. H.; Kumar, Y. B. N.

    2016-06-01

    In this paper, for the first time, the impact of drain doping profile on device electrostatics and circuit performance of novel InAs/Si Hetero-junction Double Gate Tunnel Field Effect Transistor (H-DGTFET) has been investigated. A highly doped layer placed near the source and channel junction decreases the width of the depletion region, thus, improving the ON-current and circuit performance. For this purpose, the effects of drain doping profile on the analog/RF performance of H-DGTFET is studied in terms of transconductance (gm), parasitic capacitances, cut-off frequency (fT) and gain bandwidth (GBW) product. The value of fT is increased by 13.84% and the GBW is improved by 144.7% for GD profile in Drain with CL = 0.05 when compared to UD profile. Further, the impact of drain doping profile on the circuit performance has been investigated by implementing digital and analog/RF circuits most widely used for nanoelectronic applications. For this, Verilog-A model has been developed for InAs/Si H-DGTFET. The circuit level performance assessment is carried out by implementing inverter, common source amplifier, inverter amplifier and pseudo differential amplifier by using Complementary TFET (CTFET) technology in a Verilog-A environment.

  5. Multiple Schottky Barrier-Limited Field-Effect Transistors on a Single Si Nanowire with an Intrinsic Doping Gradient.

    Science.gov (United States)

    Barreda, Jorge L; Keiper, Timothy D; Zhang, Mei; Xiong, Peng

    2017-03-09

    In comparison to conventional (channel-limited) field-effect transistors (FETs), Schottky barrier-limited FETs possess some unique characteristics which make them attractive candidates for some electronic and sensing applications. Consequently, modulation of the nano Schottky barrier at a metal-semiconductor interface promises higher performance for chemical and biomolecular sensor applications when compared to conventional FETs with Ohmic contacts. However, the fabrication and optimization of devices with a combination of ideal Ohmic and Schottky contacts as the source and drain respectively present many challenges. We address this issue by utilizing Si nanowires (NWs) synthesized by a chemical vapor deposition process which yields a pronounced doping gradient along the length of the NWs. Devices with a series of metal contacts on a single Si NW are fabricated in a single lithography and metallization process. The graded doping profile of the NW is manifested in monotonic increases in the channel and junction resistances and variation of the nature of the contacts from Ohmic to Schottky of increasing effective barrier height along the NW. Hence multiple single Schottky junction-limited FETs with extreme asymmetry and high reproducibility are obtained on an individual NW. A definitive correlation between increasing Schottky-barrier height and enhanced gate modulation is revealed. Having access to systematically varying Schottky barrier contacts on the same NW device provides an ideal platform for identifying optimal device characteristics for sensing and electronic applications.

  6. High-Resolution ac Measurements of the Hall Effect in Organic Field-Effect Transistors

    Science.gov (United States)

    Chen, Y.; Yi, H. T.; Podzorov, V.

    2016-03-01

    We describe a high resolving power technique for Hall-effect measurements, efficient in determining Hall mobility and carrier density in organic field-effect transistors and other low-mobility systems. We utilize a small low-frequency ac magnetic field (Brmsphase-sensitive (lock-in) detection of Hall voltage, with the necessary corrections for Faraday induction. This method significantly enhances the signal-to-noise ratio and eliminates the necessity of using high magnetic fields in Hall-effect studies. With the help of this method, we are able to obtain the Hall mobility and carrier density in organic transistors with a mobility as low as μ ˜0.3 cm2 V-1 s-1 by using a compact desktop apparatus and low magnetic fields. We find a good agreement between Hall-effect and electric-field-effect measurements, indicating that, contrary to the common belief, certain organic semiconductors with mobilities below 1 cm2 V-1 s-1 can still exhibit a fully developed, band-semiconductor-like Hall effect, with the Hall mobility and carrier density matching those obtained in longitudinal transistor measurements. This suggests that, even when μ organic semiconductors can still behave as delocalized coherent carriers. This technique paves the way to ubiquitous Hall-effect studies in a wide range of low-mobility materials and devices, where it is typically very difficult to resolve the Hall effect even in very high dc magnetic fields.

  7. Inkjet printed, high mobility inorganic-oxide field effect transistors processed at room temperature.

    Science.gov (United States)

    Dasgupta, Subho; Kruk, Robert; Mechau, Norman; Hahn, Horst

    2011-12-27

    Printed electronics (PE) represents any electronic devices, components or circuits that can be processed using modern-day printing techniques. Field-effect transistors (FETs) and logics are being printed with intended applications requiring simple circuitry on large, flexible (e.g., polymer) substrates for low-cost and disposable electronics. Although organic materials have commonly been chosen for their easy printability and low temperature processability, high quality inorganic oxide-semiconductors are also being considered recently. The intrinsic mobility of the inorganic semiconductors are always by far superior than the organic ones; however, the commonly expressed reservations against the inorganic-based printed electronics are due to major issues, such as high processing temperatures and their incompatibility with solution-processing. Here we show a possibility to circumvent these difficulties and demonstrate a room-temperature processed and inkjet printed inorganic-oxide FET where the transistor channel is composed of an interconnected nanoparticle network and a solid polymer electrolyte serves as the dielectric. Even an extremely conservative estimation of the field-effect mobility of such a device yields a value of 0.8 cm(2)/(V s), which is still exceptionally large for a room temperature processed and printed transistor from inorganic materials.

  8. Patterning technology for solution-processed organic crystal field-effect transistors

    Science.gov (United States)

    Li, Yun; Sun, Huabin; Shi, Yi; Tsukagoshi, Kazuhito

    2014-04-01

    Organic field-effect transistors (OFETs) are fundamental building blocks for various state-of-the-art electronic devices. Solution-processed organic crystals are appreciable materials for these applications because they facilitate large-scale, low-cost fabrication of devices with high performance. Patterning organic crystal transistors into well-defined geometric features is necessary to develop these crystals into practical semiconductors. This review provides an update on recent development in patterning technology for solution-processed organic crystals and their applications in field-effect transistors. Typical demonstrations are discussed and examined. In particular, our latest research progress on the spin-coating technique from mixture solutions is presented as a promising method to efficiently produce large organic semiconducting crystals on various substrates for high-performance OFETs. This solution-based process also has other excellent advantages, such as phase separation for self-assembled interfaces via one-step spin-coating, self-flattening of rough interfaces, and in situ purification that eliminates the impurity influences. Furthermore, recommendations for future perspectives are presented, and key issues for further development are discussed.

  9. Photo-excited charge collection spectroscopy probing the traps in field-effect transistors

    CERN Document Server

    Im, Seongil; Kim, Jae Hoon

    2013-01-01

    Solid state field-effect devices such as organic and inorganic-channel thin-film transistors (TFTs) have been expected to promote advances in display and sensor electronics. The operational stabilities of such TFTs are thus important, strongly depending on the nature and density of charge traps present at the channel/dielectric interface or in the thin-film channel itself. This book contains how to characterize these traps, starting from the device physics of field-effect transistor (FET). Unlike conventional analysis techniques which are away from well-resolving spectral results, newly-introduced photo-excited charge-collection spectroscopy (PECCS) utilizes the photo-induced threshold voltage response from any type of working transistor devices with organic-, inorganic-, and even nano-channels, directly probing on the traps. So, our technique PECCS has been discussed through more than ten refereed-journal papers in the fields of device electronics, applied physics, applied chemistry, nano-devices and materia...

  10. Patterning technology for solution-processed organic crystal field-effect transistors

    Directory of Open Access Journals (Sweden)

    Yun Li

    2014-04-01

    Full Text Available Organic field-effect transistors (OFETs are fundamental building blocks for various state-of-the-art electronic devices. Solution-processed organic crystals are appreciable materials for these applications because they facilitate large-scale, low-cost fabrication of devices with high performance. Patterning organic crystal transistors into well-defined geometric features is necessary to develop these crystals into practical semiconductors. This review provides an update on recent development in patterning technology for solution-processed organic crystals and their applications in field-effect transistors. Typical demonstrations are discussed and examined. In particular, our latest research progress on the spin-coating technique from mixture solutions is presented as a promising method to efficiently produce large organic semiconducting crystals on various substrates for high-performance OFETs. This solution-based process also has other excellent advantages, such as phase separation for self-assembled interfaces via one-step spin-coating, self-flattening of rough interfaces, and in situ purification that eliminates the impurity influences. Furthermore, recommendations for future perspectives are presented, and key issues for further development are discussed.

  11. Deep-submicron Graphene Field-Effect Transistors with State-of-Art fmax.

    Science.gov (United States)

    Lyu, Hongming; Lu, Qi; Liu, Jinbiao; Wu, Xiaoming; Zhang, Jinyu; Li, Junfeng; Niu, Jiebin; Yu, Zhiping; Wu, Huaqiang; Qian, He

    2016-10-24

    In order to conquer the short-channel effects that limit conventional ultra-scale semiconductor devices, two-dimensional materials, as an option of ultimate thin channels, receive wide attention. Graphene, in particular, bears great expectations because of its supreme carrier mobility and saturation velocity. However, its main disadvantage, the lack of bandgap, has not been satisfactorily solved. As a result, maximum oscillation frequency (fmax) which indicates transistors' power amplification ability has been disappointing. Here, we present submicron field-effect transistors with specially designed low-resistance gate and excellent source/drain contact, and therefore significantly improved fmax. The fabrication was assisted by the advanced 8-inch CMOS back-end-of-line technology. A 200-nm-gate-length GFET achieves fT/fmax = 35.4/50 GHz. All GFET samples with gate lengths ranging from 200 nm to 400 nm possess fmax 31-41% higher than fT, closely resembling Si n-channel MOSFETs at comparable technology nodes. These results re-strengthen the promise of graphene field-effect transistors in next generation semiconductor electronics.

  12. N-channel field-effect transistors with an organic-inorganic layered perovskite semiconductor

    Science.gov (United States)

    Matsushima, Toshinori; Mathevet, Fabrice; Heinrich, Benoît; Terakawa, Shinobu; Fujihara, Takashi; Qin, Chuanjiang; Sandanayaka, Atula S. D.; Ribierre, Jean-Charles; Adachi, Chihaya

    2016-12-01

    Large electron injection barriers and electrode degradation are serious issues that need to be overcome to obtain n-channel operation in field-effect transistors with an organic-inorganic layered perovskite (C6H5C2H4NH3)2SnI4 semiconductor. By employing low-work-function Al source/drain electrodes and by inserting C60 layers between the perovskite semiconductor and the Al electrodes to reduce the injection barrier and to suppress the electrode degradation, we demonstrate n-channel perovskite transistors with electron mobilities of up to 2.1 cm2/V s, the highest value ever reported in spin-coated perovskite transistors. The n-channel transport properties of these transistors are relatively stable in vacuum but are very sensitive to oxygen, which works as electron traps in perovskite and C60 layers. In addition, grazing-incidence X-ray scattering and thermally stimulated current measurements revealed that crystallite size and electron traps largely affect the n-channel transport properties.

  13. Bias stress effect and recovery in organic field effect transistors: proton migration mechanism

    Science.gov (United States)

    Sharma, A.; Mathijssen, Simon G. J.; Kemerink, M.; de Leeuw, Dago M.; Bobbert, Peter A.

    2010-08-01

    Organic field-effect transistors exhibit operational instabilities when a gate bias is applied. For a constant gate bias the threshold voltage shifts towards the applied gate bias voltage, an effect known as the bias-stress effect. We have performed a detailed experimental and theoretical study of operational instabilities in p-type transistors with silicon-dioxide gate dielectric. We propose a mechanism in which holes in the semiconductor are converted into protons in the presence of water and a reversible migration of these protons into the gate dielectric to explain the instabilities in organic transistors. We show how redistribution of charge between holes in the semiconductor and protons in the gate dielectric can consistently explain the experimental observations. Furthermore, we explain in detail the recovery of a pres-stressed transistor on applying zero gate bias. We show that recovery dynamics depends strongly on the extent of stressing. Our mechanism is consistent with the known aspects of bias-stress effect like acceleration due to humidity, constant activation energy and reversibility.

  14. Work function engineering of graphene oxide via covalent functionalization for organic field-effect transistors

    Science.gov (United States)

    Ji, Seulki; Min, Bok Ki; Kim, Seong K.; Myung, Sung; Kang, Minseo; Shin, Hong-Suk; Song, Wooseok; Heo, Jungseok; Lim, Jongsun; An, Ki-Seok; Lee, Ill-Young; Lee, Sun Sook

    2017-10-01

    We report a simple method to produce work-function-tuned graphene nanosheets based on the nucleophilic substitution of the epoxy groups on graphene oxide. The electrical property of the graphene oxide is controlled dramatically, which results in the apparent work functions in a broad range between 3.73 eV and 5.1 eV, by attaching various functional groups on the graphene surface. As a proof of concept, we successfully demonstrated organic field effect transistors incorporating the functionalized graphene nanosheet interlayers. Here, when nanosheets were applied in an organic transistor as the interlayer material between electrodes and organic channel, the device performance was significantly improved. Our approach can be utilized to increase the performance and the flexibility of various advanced carbon-material-based hybrid electrical devices.

  15. Tunnel field-effect transistors as energy-efficient electronic switches.

    Science.gov (United States)

    Ionescu, Adrian M; Riel, Heike

    2011-11-16

    Power dissipation is a fundamental problem for nanoelectronic circuits. Scaling the supply voltage reduces the energy needed for switching, but the field-effect transistors (FETs) in today's integrated circuits require at least 60 mV of gate voltage to increase the current by one order of magnitude at room temperature. Tunnel FETs avoid this limit by using quantum-mechanical band-to-band tunnelling, rather than thermal injection, to inject charge carriers into the device channel. Tunnel FETs based on ultrathin semiconducting films or nanowires could achieve a 100-fold power reduction over complementary metal-oxide-semiconductor (CMOS) transistors, so integrating tunnel FETs with CMOS technology could improve low-power integrated circuits.

  16. Effect of Temperature on GaGdO/GaN Metal Oxide Semiconductor Field Effect Transistors

    Energy Technology Data Exchange (ETDEWEB)

    Abernathy, C.R.; Baca, A.; Chu, S.N.G.; Hong, M.; Lothian, J.R.; Marcus, M.A.; Pearton, S.J.; Ren, F.; Schurman, M.J.

    1998-10-14

    GaGdO was deposited on GaN for use as a gate dielectric in order to fabricate a depletion metal oxide semiconductor field effect transistor (MOSFET). This is the fmt demonstration of such a device in the III-Nitride system. Analysis of the effect of temperature on the device shows that gate leakage is significantly reduced at elevated temperature relative to a conventional metal semiconductor field effeet transistor (MESFET) fabricated on the same GaN layer. MOSFET device operation in fact improved upon heating to 400 C. Modeling of the effeet of temperature on contact resistance suggests that the improvement is due to a reduction in the parasitic resistances present in the device.

  17. Field-effect transistors based on self-organized molecular nanostripes

    DEFF Research Database (Denmark)

    Cavallini, M.; Stoliare, P.; Moulin, J.-F.

    2005-01-01

    Charge transport properties in organic semiconductors depend strongly on molecular order. Here we demonstrate field-effect transistors where drain current flows through a precisely defined array of nanostripes made of crystalline and highly ordered molecules. The molecular stripes are fabricated...... across the channel of the transistor by a stamp-assisted deposition of the molecular semiconductors from a solution. As the solvent evaporates, the capillary forces drive the solution to form menisci under the stamp protrusions. The solute precipitates only in the regions where the solution is confined...... by the menisci once the critical concentration is reached and self-organizes into molecularly ordered stripes 100-200 nm wide and a few monolayers high. The charge mobility measured along the stripes is 2 orders of magnitude larger than the values measured for spin-coated thin films....

  18. Current steering detection scheme of three terminal antenna-coupled terahertz field effect transistor detectors.

    Science.gov (United States)

    Földesy, Péter

    2013-08-01

    An antenna-coupled field effect transistor (FET) as a plasma wave terahertz detector is used with the current steering to record separately the gate-source and gate-drain photoresponses and their phase sensitive combination. This method is based on the observation that the plasmon-terminal coupling is cut off in saturation, resulting in only one-sided sensitivity. A polarimetric example is presented with intensity and polarization angle reconstruction using a single three-terminal antenna-coupled Si-metal-oxide semiconductor FET (MOSFET). The technique is applicable to various detection schemes and technologies (high electron mobility transistors and GaAs-, GaN-, and Si-MOSFETs), and other application possibilities are discussed.

  19. Strained silicon/silicon germanium heterojunction n-channel metal oxide semiconductor field effect transistors

    CERN Document Server

    Olsen, S H

    2002-01-01

    Investigations into the performance of strained silicon/silicon-germanium (Si/SiGe) n-channel metal-oxide-semiconductor field effect transistors (MOSFETs) have been carried out. Theoretical predictions suggest that use of a strained Si/SiGe material system with advanced material properties compared with conventional silicon allows enhanced MOSFET device performance. This study has therefore investigated the practical feasibility of obtaining superior electrical performance using a Si/SiGe material system. The MOSFET devices consisted of a strained Si surface channel and were fabricated on relaxed SiGe material using a reduced thermal budget process in order to preserve the strain. Two batches of strained Si/SiGe devices fabricated on material grown by differing methods have been analysed and both showed good transistor action. A correlation of electrical and physical device data established that the electrical device behaviour was closely related to the SiGe material quality, which differed depending on growt...

  20. Studies on different configurations of cobalt phthalocyanine based flexible organic field effect transistor

    Science.gov (United States)

    Kumar, A.; Jha, P.; Samanta, S.; Singh, A.; Debnath, A. K.; Aswal, D. K.; Gupta, S. K.

    2016-05-01

    Organic Field Effect Transistors (OFETs) are being investigated for a number of low-cost, large area applications; particularly those that are compatible with flexible plastic substrates. Development of low temperature processes can make way for OFETs to be integrated on flexible plastic substrates. Here we have made systematic studies on OFETs in different configurations wherein we have chosen Cobalt Phthalocyanine (CoPc) as active material. We have found the best mobility (1.86 × 10-5 cm2/V-s) in Bottom Gate Top Contact configuration. However, threshold voltage (-5V) and On off ratio (62)were found to be better in Top Gate Bottom Contact configuration The electromechanical properties of the Bottom Gate Top Contact transistors were studied by measuring the transfer characteristics of the devices in bend condition and thereby calculating mobility under different radii of bending. No significant change in the mobility of the device was observed under bent conditions.

  1. The study of ambipolar behavior in phosphorene field-effect transistors

    Science.gov (United States)

    Guo, Cheng; Wang, Lin; Xing, Huaizhong; Chen, Xiaoshuang

    2016-12-01

    The electrical characteristics of phosphorene field effect transistors (FETs) were investigated with the two-dimensional (2D) numerical simulation. In this study, it is found that the Schottky barrier plays an important role in the ambipolar transfer characteristics of phosphorene-based FETs. It is demonstrated that when the barrier heights are equal between electron and hole doping, the ambipolar current output dominates across the whole bias range. In the meantime, the saturation leakage current output of the transfer characteristic is only determined by the number of phosphorene layers or the bandgap rather than the Schottky barrier height between phosphorene and metal contact. The ambipolar behaviors become more pronounced as the channel lengths of transistors are decreased, all the geometric and material parameters are taken into account to improve the ambipolar output and understanding its underlying mechanisms. The presented results open the path to design phosphorene-based logic device, photo detector with low dark current for both electronic and optoelectronic applications.

  2. Dithiopheneindenofluorene (TIF) Semiconducting Polymers with Very High Mobility in Field-Effect Transistors

    KAUST Repository

    Chen, Hu

    2017-07-19

    The charge-carrier mobility of organic semiconducting polymers is known to be enhanced when the energetic disorder of the polymer is minimized. Fused, planar aromatic ring structures contribute to reducing the polymer conformational disorder, as demonstrated by polymers containing the indacenodithiophene (IDT) repeat unit, which have both a low Urbach energy and a high mobility in thin-film-transistor (TFT) devices. Expanding on this design motif, copolymers containing the dithiopheneindenofluorene repeat unit are synthesized, which extends the fused aromatic structure with two additional phenyl rings, further rigidifying the polymer backbone. A range of copolymers are prepared and their electrical properties and thin-film morphology evaluated, with the co-benzothiadiazole polymer having a twofold increase in hole mobility when compared to the IDT analog, reaching values of almost 3 cm2 V−1 s−1 in bottom-gate top-contact organic field-effect transistors.

  3. Numerical Study on a Lateral Double-Gate Tunnelling Field Effect Transistor

    Institute of Scientific and Technical Information of China (English)

    HE Jin; BIAN Wei; TAO Ya-Dong; LIU Feng; SONG Yan; ZHANG Xing

    2006-01-01

    A novel lateral double-gate tunnelling field effect transistor (DG-TFET) is studied and its performance is presented by a two-dimensional device simulation with code ISE. The result demonstrates that this new tunnelling transistor allows for the steeper sub-threshold swing below 60mV/dec, the super low supply voltage (operable at VDD < 0.3 V) and the rail-to-rail logic (significant on-state current at the drain-source voltage VDS = 50 mV)for the aggressive technology assumptions of the availability of high-k/metal stack with equivalent gate oxide thickness EOT =0.24 nm and the work function difference 4.5eV of materials.

  4. Integrating carbon nanotubes into silicon by means of vertical carbon nanotube field-effect transistors

    KAUST Repository

    Li, Jingqi

    2014-01-01

    Single-walled carbon nanotubes have been integrated into silicon for use in vertical carbon nanotube field-effect transistors (CNTFETs). A unique feature of these devices is that a silicon substrate and a metal contact are used as the source and drain for the vertical transistors, respectively. These CNTFETs show very different characteristics from those fabricated with two metal contacts. Surprisingly, the transfer characteristics of the vertical CNTFETs can be either ambipolar or unipolar (p-type or n-type) depending on the sign of the drain voltage. Furthermore, the p-type/n-type character of the devices is defined by the doping type of the silicon substrate used in the fabrication process. A semiclassical model is used to simulate the performance of these CNTFETs by taking the conductance change of the Si contact under the gate voltage into consideration. The calculation results are consistent with the experimental observations. This journal is © the Partner Organisations 2014.

  5. Si/Ge hetero-structure nanotube tunnel field effect transistor

    KAUST Repository

    Hanna, A. N.

    2015-01-07

    We discuss the physics of conventional channel material (silicon/germanium hetero-structure) based transistor topology mainly core/shell (inner/outer) gated nanotube vs. gate-all-around nanowire architecture for tunnel field effect transistor application. We show that nanotube topology can result in higher performance through higher normalized current when compared to nanowire architecture at Vdd-=-1-V due to the availability of larger tunneling cross section and lower Shockley-Reed-Hall recombination. Both architectures are able to achieve sub 60-mV/dec performance for more than five orders of magnitude of drain current. This enables the nanotube configuration achieving performance same as the nanowire architecture even when Vdd is scaled down to 0.5-V.

  6. Strong Coulomb scattering effects on low frequency noise in monolayer WS2 field-effect transistors

    Science.gov (United States)

    Joo, Min-Kyu; Yun, Yoojoo; Yun, Seokjoon; Lee, Young Hee; Suh, Dongseok

    2016-10-01

    When atomically thin semiconducting transition metal dichalcogenides are used as a channel material, they are inevitably exposed to supporting substrates. This situation can lead to masking of intrinsic properties by undesired extrinsic doping and/or additional conductance fluctuations from the largely distributed Coulomb impurities at the interface between the channel and the substrate. Here, we report low-frequency noise characteristics in monolayer WS2 field-effect transistors on silicon/silicon-oxide substrate. To mitigate the effect of extrinsic low-frequency noise sources, a nitrogen annealing was carried out to provide better interface quality and to suppress the channel access resistance. The carrier number fluctuation and the correlated mobility fluctuation (CNF-CMF) model was better than the sole CNF one to explain our low-frequency noise data, because of the strong Coulomb scattering effect on the effective mobility caused by carrier trapping/detrapping at oxide traps. The temperature-dependent field-effect mobility in the four-probe configuration and the Coulomb scattering parameters are presented to support this strong Coulomb scattering effect on carrier transport in monolayer WS2 field-effect transistor.

  7. Facile fabrication of electrolyte-gated single-crystalline cuprous oxide nanowire field-effect transistors

    Science.gov (United States)

    Stoesser, Anna; von Seggern, Falk; Purohit, Suneeti; Nasr, Babak; Kruk, Robert; Dehm, Simone; Wang, Di; Hahn, Horst; Dasgupta, Subho

    2016-10-01

    Oxide semiconductors are considered to be one of the forefront candidates for the new generation, high-performance electronics. However, one of the major limitations for oxide electronics is the scarcity of an equally good hole-conducting semiconductor, which can provide identical performance for the p-type metal oxide semiconductor field-effect transistors as compared to their electron conducting counterparts. In this quest, here we present a bulk synthesis method for single crystalline cuprous oxide (Cu2O) nanowires, their chemical and morphological characterization and suitability as active channel material in electrolyte-gated, low-power, field-effect transistors (FETs) for portable and flexible logic circuits. The bulk synthesis method used in the present study includes two steps: namely hydrothermal synthesis of the nanowires and the removal of the surface organic contaminants. The surface treated nanowires are then dispersed on a receiver substrate where the passive electrodes are structured, followed by printing of a composite solid polymer electrolyte (CSPE), chosen as the gate insulator. The characteristic electrical properties of individual nanowire FETs are found to be quite interesting including accumulation-mode operation and field-effect mobility of 0.15 cm2 V-1 s-1.

  8. 25th anniversary article: organic field-effect transistors: the path beyond amorphous silicon.

    Science.gov (United States)

    Sirringhaus, Henning

    2014-03-05

    Over the past 25 years, organic field-effect transistors (OFETs) have witnessed impressive improvements in materials performance by 3-4 orders of magnitude, and many of the key materials discoveries have been published in Advanced Materials. This includes some of the most recent demonstrations of organic field-effect transistors with performance that clearly exceeds that of benchmark amorphous silicon-based devices. In this article, state-of-the-art in OFETs are reviewed in light of requirements for demanding future applications, in particular active-matrix addressing for flexible organic light-emitting diode (OLED) displays. An overview is provided over both small molecule and conjugated polymer materials for which field-effect mobilities exceeding > 1 cm(2) V(-1) s(-1) have been reported. Current understanding is also reviewed of their charge transport physics that allows reaching such unexpectedly high mobilities in these weakly van der Waals bonded and structurally comparatively disordered materials with a view towards understanding the potential for further improvement in performance in the future.

  9. A subthermionic tunnel field-effect transistor with an atomically thin channel

    Science.gov (United States)

    Sarkar, Deblina; Xie, Xuejun; Liu, Wei; Cao, Wei; Kang, Jiahao; Gong, Yongji; Kraemer, Stephan; Ajayan, Pulickel M.; Banerjee, Kaustav

    2015-10-01

    The fast growth of information technology has been sustained by continuous scaling down of the silicon-based metal-oxide field-effect transistor. However, such technology faces two major challenges to further scaling. First, the device electrostatics (the ability of the transistor's gate electrode to control its channel potential) are degraded when the channel length is decreased, using conventional bulk materials such as silicon as the channel. Recently, two-dimensional semiconducting materials have emerged as promising candidates to replace silicon, as they can maintain excellent device electrostatics even at much reduced channel lengths. The second, more severe, challenge is that the supply voltage can no longer be scaled down by the same factor as the transistor dimensions because of the fundamental thermionic limitation of the steepness of turn-on characteristics, or subthreshold swing. To enable scaling to continue without a power penalty, a different transistor mechanism is required to obtain subthermionic subthreshold swing, such as band-to-band tunnelling. Here we demonstrate band-to-band tunnel field-effect transistors (tunnel-FETs), based on a two-dimensional semiconductor, that exhibit steep turn-on; subthreshold swing is a minimum of 3.9 millivolts per decade and an average of 31.1 millivolts per decade for four decades of drain current at room temperature. By using highly doped germanium as the source and atomically thin molybdenum disulfide as the channel, a vertical heterostructure is built with excellent electrostatics, a strain-free heterointerface, a low tunnelling barrier, and a large tunnelling area. Our atomically thin and layered semiconducting-channel tunnel-FET (ATLAS-TFET) is the only planar architecture tunnel-FET to achieve subthermionic subthreshold swing over four decades of drain current, as recommended in ref. 17, and is also the only tunnel-FET (in any architecture) to achieve this at a low power-supply voltage of 0.1 volts. Our

  10. Electrical Characterisation of Ferroelectric Field Effect Transistors based on Ferroelectric HfO2 Thin Films

    OpenAIRE

    Yurchuk, Ekaterina

    2015-01-01

    Ferroelectric field effect transistor (FeFET) memories based on a new type of ferroelectric material (silicon doped hafnium oxide) were studied within the scope of the present work. Utilisation of silicon doped hafnium oxide (Si:HfO2) thin films instead of conventional perovskite ferroelectrics as a functional layer in FeFETs provides compatibility to the CMOS process as well as improved device scalability. The influence of different process parameters on the properties of Si:HfO2 thin films ...

  11. Field-effect and capacitive properties of water-gated transistors based on polythiophene derivatives

    Directory of Open Access Journals (Sweden)

    R. Porrazzo

    2015-01-01

    Full Text Available Recently, water-gated organic field-effect transistors (WGOFET have been intensively studied for their application in the biological field. Surprisingly, a very limited number of conjugated polymers have been reported so far. Here, we systematically explore a series of polythiophene derivatives, presenting different alkyl side chains lengths and orientation, and characterized by various morphologies: comparative evaluation of their performances allows highlighting the critical role played by alkyl side chains, which significantly affects the polymer/water interface capacitance. Reported results provide useful guidelines towards further development of WGOFETs and represent a step forward in the understanding of the polymer/water interface phenomena.

  12. Anomalous Response in Heteroacene-Based Organic Field Effect Transistors under High Pressure

    Directory of Open Access Journals (Sweden)

    Ken-ichi Sakai

    2014-04-01

    Full Text Available Carrier transport properties of organic field effect transistors in dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene single crystals have been investigated under high pressure. In contrast to the typical pressure effect of monotonic increase in charge transfer rates according to the application of external hydrostatic pressure, it is clarified that the present organic semiconductor devices exhibit nonmonotonic pressure response, such as negative pressure effect. X-ray diffraction analysis under high pressure reveals that on-site molecular orientation and displacement in the heteroacene molecule is assumed to be the origin for the anomalous pressure effects.

  13. All-graphene field-effect transistor based on lateral tunnelling

    Science.gov (United States)

    Svintsov, D.; Vyurkov, V.; Orlikovsky, A.; Ryzhii, V.; Otsuji, T.

    2014-03-01

    A novel lateral all-graphene tunnel field-effect transistor (FET) with superior ON/OFF current switching ratio is proposed and simulated. The structure consists of two coplanar graphene layers serving as source and drain separated by a narrow tunnel gap. Both barrier transparency and tunnel density of states are controlled by top and bottom gates made of graphene too. The proposed FET exhibits an ultrahigh frequency performance inherent to graphene along with a subthreshold slope approaching the thermionic limit and current saturation inherent to common semiconductor FETs.

  14. Switching Characteristics of Phase Change Memory Cell Integrated with Metal-Oxide Semiconductor Field Effect Transistor

    Institute of Scientific and Technical Information of China (English)

    XU Cheng; CHEN Bomy; LIU Bo; CHEN Yi-Feng; LIANG Shuang; SONG Zhi-Tang; FENG Song-Lin; WAN Xu-Dong; YANG Zuo-Ya; XIE Joseph

    2008-01-01

    A Ge2Sb2Te5 based phase change memory device cell integrated with metal-oxide semiconductor field effect transistor (MOSFET) is fabricated using standard 0.18 μm complementary metal-oxide semiconductor process technology.It shows steady switching characteristics in the dc current-voltage measurement.The phase changing phenomenon from crystalline state to amorphous state with a voltage pulse altitude of 2.0 V and pulse width of 50 ns is also obtained.These results show the feasibility of integrating phase change memory cell with MOSFET.

  15. Extended-gate organic field-effect transistor for the detection of histamine in water

    Science.gov (United States)

    Minamiki, Tsukuru; Minami, Tsuyoshi; Yokoyama, Daisuke; Fukuda, Kenjiro; Kumaki, Daisuke; Tokito, Shizuo

    2015-04-01

    As part of our ongoing research program to develop health care sensors based on organic field-effect transistor (OFET) devices, we have attempted to detect histamine using an extended-gate OFET. Histamine is found in spoiled or decayed fish, and causes foodborne illness known as scombroid food poisoning. The new OFET device possesses an extended gate functionalized by carboxyalkanethiol that can interact with histamine. As a result, we have succeeded in detecting histamine in water through a shift in OFET threshold voltage. This result indicates the potential utility of the designed OFET devices in food freshness sensing.

  16. Electrolyte-gated graphene field-effect transistors for detecting pH and protein adsorption.

    Science.gov (United States)

    Ohno, Yasuhide; Maehashi, Kenzo; Yamashiro, Yusuke; Matsumoto, Kazuhiko

    2009-09-01

    We investigated electrolyte-gated graphene field-effect transistors (GFETs) for electrical detecting pH and protein adsorptions. Nonfunctionalized single-layer graphene was used as a channel. GFETs immersed in an electrolyte showed transconductances 30 times higher than those in a vacuum and their conductances exhibited a direct linear increase with electrolyte pH, indicating their potential for use in pH sensor applications. We also attempted to direct surface-protein adsorption and showed that the conductance of GFETs increased with exposure to a protein at several hundred picomolar. The GFETs thus acted as highly sensitive electrical sensors for detecting pH and biomolecule concentrations.

  17. Spatial profile of charge storage in organic field-effect transistor nonvolatile memory using polymer electret

    Science.gov (United States)

    She, Xiao-Jian; Liu, Jie; Zhang, Jing-Yu; Gao, Xu; Wang, Sui-Dong

    2013-09-01

    Spatial profile of the charge storage in the pentacene-based field-effect transistor nonvolatile memories using poly(2-vinyl naphthalene) electret is probed. The electron trapping into the electret after programming can be space dependent with more electron storage in the region closer to the contacts, and reducing the channel length is an effective approach to improve the memory performance. The deficient electron supply in pentacene is proposed to be responsible for the inhomogeneous electron storage in the electret. The hole trapping into the electret after erasing is spatially homogeneous, arising from the sufficient hole accumulation in the pentacene channel.

  18. Functionalization and microfluidic integration of silicon nanowire biologically gated field effect transistors

    DEFF Research Database (Denmark)

    Pfreundt, Andrea

    with nanowire sensors functionalized using different modification schemes. To facilitate functionalization and measurement and as a first step towards integration into a point-of-care device, several microfluidic tools were developed for sample delivery to the sensor surface and as a modular platform......This thesis deals with the development of a novel biosensor for the detection of biomolecules based on a silicon nanowire biologically gated field-effect transistor and its integration into a point-of-care device. The sensor and electrical on-chip integration was developed in a different project...

  19. Ballistic electron transport calculation of strained germanium-tin fin field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Lan, H.-S. [Graduate Institute of Electronics Engineering and Department of Electrical Engineering, National Taiwan University, Taipei, Taiwan (China); Liu, C. W., E-mail: chee@cc.ee.ntu.edu.tw [Graduate Institute of Electronics Engineering and Department of Electrical Engineering, National Taiwan University, Taipei, Taiwan (China); Graduate Institute of Photonics and Optoelectronics, National Taiwan University, Taipei, Taiwan (China)

    2014-05-12

    The dependence of ballistic electron current on Sn content, sidewall orientations, fin width, and uniaxial stress is theoretically studied for the GeSn fin field-effect transistors. Alloying Sn increases the direct Γ valley occupancy and enhances the injection velocity at virtual source node. (112{sup ¯}) sidewall gives the highest current enhancement due to the rapidly increasing Γ valley occupancy. The non-parabolicity of the Γ valley affects the occupancy significantly. However, uniaxial tensile stress and the shrinkage of fin width reduce the Γ valley occupancy, and the currents are enhanced by increasing occupancy of specific indirect L valleys with high injection velocity.

  20. Nanomechanoelectronic signal transduction scheme with metal-oxide-semiconductor field-effect transistor-embedded microcantilevers

    Science.gov (United States)

    Tark, Soo-Hyun; Srivastava, Arvind; Chou, Stanley; Shekhawat, Gajendra; Dravid, Vinayak P.

    2009-03-01

    We explore various metal-oxide-semiconductor field-effect transistor (MOSFET)-embedded microcantilever designs to assess their performance as an efficient nanomechanoelectronic signal transduction platform for monitoring deflection in microcantilever-based phenomena such as biochemical sensing and actuation. The current-voltage characteristics of embedded MOSFETs show current noise in the nanoampere range with a large signal-to-noise ratio sufficient to provide measureable output signal. The change in drain current with cantilever deflection is consistent with the effect of stress on carrier mobility and drain current reported in previous studies, validating that the MOSFET cantilevers can directly transduce deflection of a microcantilever into reproducible change in electrical signal.

  1. High temperature study of flexible silicon-on-insulator fin field-effect transistors

    KAUST Repository

    Diab, Amer El Hajj

    2014-09-29

    We report high temperature electrical transport characteristics of a flexible version of the semiconductor industry\\'s most advanced architecture: fin field-effect transistor on silicon-on-insulator with sub-20 nm fins and high-κ/metal gate stacks. Characterization from room to high temperature (150 °C) was completed to determine temperature dependence of drain current (Ids), gate leakage current (Igs), transconductance (gm), and extracted low-field mobility (μ0). Mobility degradation with temperature is mainly caused by phonon scattering. The other device characteristics show insignificant difference at high temperature which proves the suitability of inorganic flexible electronics with advanced device architecture.

  2. Dual-Material Surrounding-Gate Metal-Oxide-Semiconductor Field Effect Transistors with Asymmetric Halo

    Institute of Scientific and Technical Information of China (English)

    LI Zun-Chao

    2009-01-01

    Asymmetrical halo and dual-material gate structure are used in the sub-100 nm surrounding-gate metal-oxide-semiconductor field effect transistor (MOSFET) to improve the performance. Using three-region parabolic po-tential distribution and universal boundary condition, analytical surface potential and threshold voltage models of the novel MOSFET are developed based on the solution of Poisson's equation. The performance of the MOS-FET is examined by the analytical models and the 3D numerical device simulator Davinci. It is shown that the novel MOSFET can suppress short channel effect and improve carrier transport efficiency. The derived analytical models agree well with Davinci.

  3. DESIGN OF MODULO-6-COUNTER USING CARBON NANOTUBE FIELD EFFECT TRANSISTOR

    Directory of Open Access Journals (Sweden)

    V.Saravanan

    2012-11-01

    Full Text Available In many digital applications like digital clock, frequency divider circuit and nano applications etc., designing of low power modulo counters is highly desirable. Designing of such a counters using existing technology i.e., CMOS technology has the limitations in-terms of power consumption, device scaling limitations andfabrications difficulties in nanometre range. This paper proposes the new design technique for modulo counters using the carbon nanotube field effect transistor (CNTFET. Counter performance is analyzed interms of speed and power consumption. This paper also analyses carbon nanotube (CNT types, how the carbon nanotube is formed, and scaling limitations of the CMOS technology in nanometre range.

  4. Integrated Materials Design of Organic Semiconductors for Field-Effect Transistors

    KAUST Repository

    Mei, Jianguo

    2013-05-08

    The past couple of years have witnessed a remarkable burst in the development of organic field-effect transistors (OFETs), with a number of organic semiconductors surpassing the benchmark mobility of 10 cm2/(V s). In this perspective, we highlight some of the major milestones along the way to provide a historical view of OFET development, introduce the integrated molecular design concepts and process engineering approaches that lead to the current success, and identify the challenges ahead to make OFETs applicable in real applications. © 2013 American Chemical Society.

  5. Impact of graphene polycrystallinity on the performance of graphene field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Jiménez, David; Chaves, Ferney [Departament d' Enginyeria Electrònica, Escola d' Enginyeria, Universitat Autònoma de Barcelona, 08193-Bellaterra (Spain); Cummings, Aron W.; Van Tuan, Dinh [ICN2, Institut Català de Nanociencia i Nanotecnologia, Campus UAB, 08193 Bellaterra (Barcelona) (Spain); Kotakoski, Jani [Faculty of Physics, University of Vienna, Boltzmanngasse 5, 1090 Wien (Austria); Department of Physics, University of Helsinki, P.O. Box 43, 00014 University of Helsinki (Finland); Roche, Stephan [ICN2, Institut Català de Nanociencia i Nanotecnologia, Campus UAB, 08193 Bellaterra (Barcelona) (Spain); ICREA, Institució Catalana de Recerca i Estudis Avançats, 08070 Barcelona (Spain)

    2014-01-27

    We have used a multi-scale physics-based model to predict how the grain size and different grain boundary morphologies of polycrystalline graphene will impact the performance metrics of graphene field-effect transistors. We show that polycrystallinity has a negative impact on the transconductance, which translates to a severe degradation of the maximum and cutoff frequencies. On the other hand, polycrystallinity has a positive impact on current saturation, and a negligible effect on the intrinsic gain. These results reveal the complex role played by graphene grain boundaries and can be used to guide the further development and optimization of graphene-based electronic devices.

  6. Surface-potential-based physical compact model for graphene field effect transistor

    Science.gov (United States)

    Wang, Lingfei; Peng, Songang; Wang, Wei; Xu, Guangwei; Ji, Zhuoyu; Lu, Nianduan; Li, Ling; Jin, Zhi; Liu, Ming

    2016-08-01

    A surface potential based physical compact model for a graphene field effect transistor is proposed, including Boltzmann transport and thermally activated transport. We verified it by the experiments and Gummel symmetry test, showing good accuracy and continuity over a wide range of operation regions. Coded in Verilog-A, this model provides physics-based consistent DC and AC characteristics, which can be easily embedded into a vendor CAD tool to simulate circuits. Based on this model, a direct insight into the relationship between physical parameters and circuit performances can be achieved.

  7. Biosensors based on carbon nanotube-network field-effect transistors.

    Science.gov (United States)

    Cid, Cristina C; Riu, Jordi; Maroto, Alicia; Rius, F Xavier

    2010-01-01

    We describe in detail the different steps involved in the construction of a carbon nanotube field-effect transistor (CNTFET) based on a network of single-walled carbon nanotubes (SWCNTs), which can selectively detect human immunoglobulin G (HIgG). HIgG antibodies, which are strongly adsorbed onto the walls of the SWCNTs, are the basic elements of the recognition layer. The nonspecific binding of proteins or other interferences are avoided by covering the nonadsorbed areas of the SWCNTs with Tween 20. The CNTFET is a reagentless device that does not need labels to detect HIgG.

  8. Ambipolar Cu- and Fe-Phthalocyanine single-crystal field-effect transistors

    OpenAIRE

    de Boer, R. W. I.; Stassen, A. F.; Craciun, M. F.; Mulder, C. L.; Molinari, A; Rogge, S.; Morpurgo, A. F.

    2005-01-01

    We report the observation of ambipolar transport in field-effect transistors fabricated on single crystals of Copper- and Iron-Phthalocyanine, using gold as a high work-function metal for the fabrication of source and drain electrodes. In these devices, the room-temperature mobility of holes reaches 0.3 cm$^2$/Vs in both materials. The highest mobility for electrons is observed for Iron-Phthalocyanines and is approximately one order of magnitude lower. Our measurements indicate that these val...

  9. Origins of charge noise in carbon nanotube field-effect transistor biosensors.

    Science.gov (United States)

    Sharf, Tal; Kevek, Joshua W; Deborde, Tristan; Wardini, Jenna L; Minot, Ethan D

    2012-12-12

    Determining the major noise sources in nanoscale field-effect transistor (nanoFET) biosensors is critical for improving bioelectronic interfaces. We use the carbon nanotube (CNT) FET biosensor platform to examine the noise generated by substrate interactions and surface adsorbates, both of which are present in current nanoFET biosensors. The charge noise model is used as a quantitative framework to show that insulating substrates and surface adsorbates are both significant contributors to the noise floor of CNT FET biosensors. Removing substrate interactions and surface adsorbates reduces the power spectral density of background voltage fluctuations by 19-fold.

  10. Electric Double Layer Gate Field-Effect Transistors Based on Si

    Science.gov (United States)

    Yanase, Takashi; Shimada, Toshihiro; Hasegawa, Tetsuya

    2010-04-01

    Electric double layer field-effect transistors (EDL-FETs) were fabricated using single crystal Si wafer as the active semiconductor and various characteristics were studied including dynamic response against step-function gate bias. The static FET mobility was more than 100 cm2 V-1 s-1. The response time of the drain current was 20 µs for ionic liquid and 3 ms for poly(ethylene glycol) (PEG) solution of LiBF4. Unexpected fast response was observed at a certain “speed up bias” condition. This effect will be useful to switching circuits using EDL-FETs.

  11. High current, low voltage carbon nanotube enabled vertical organic field effect transistors.

    Science.gov (United States)

    McCarthy, Mitchell A; Liu, Bo; Rinzler, Andrew G

    2010-09-08

    State-of-the-art performance is demonstrated from a carbon nanotube enabled vertical field effect transistor using an organic channel material. The device exhibits an on/off current ratio >10(5) for a gate voltage range of 4 V with a current density output exceeding 50 mA/cm(2). The architecture enables submicrometer channel lengths while avoiding high-resolution patterning. The ability to drive high currents and inexpensive fabrication may provide the solution for the so-called OLED backplane problem.

  12. Performances of carbon nanotube field effect transistors with altered channel length

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The influence of channel length on the performances of carbon nanotube field effect transistors(CNT-FETs) has been studied.Buffered oxide etching was used to remove approximately a 60 nm layer from the original 100 nm silicon dioxide layer,to thin the dielectric layer of the back gate.Channel length of the CNT-FETs was changed along with the etching process.The dependence of drain-source current on gate voltage was measured to analyze the performance of the CNT-FETs,including the transconductance,carrier mobility,current ON/OFF ratio,etc.The results indicate that the devices still keep good quality.

  13. Dynamic response of carbon nanotube field-effect transistors analyzed by S-parameters measurement

    Energy Technology Data Exchange (ETDEWEB)

    Bethoux, J.-M. [Institut d' Electronique, de Microelectronique et de Nanotechnologie, C.N.R.S. U.M.R. 8520, BP 60069, F-59652, Villeneuve d' Ascq Cedex (France); Happy, H. [Institut d' Electronique, de Microelectronique et de Nanotechnologie, C.N.R.S. U.M.R. 8520, BP 60069, F-59652, Villeneuve d' Ascq Cedex (France)]. E-mail: henri.happy@iemn.univ-lille1.fr; Dambrine, G. [Institut d' Electronique, de Microelectronique et de Nanotechnologie, C.N.R.S. U.M.R. 8520, BP 60069, F-59652, Villeneuve d' Ascq Cedex (France); Derycke, V. [Laboratoire d' Electronique Moleculaire, SPEC, Commissariat a l' Energie Atomique, Saclay F-91191, Gif sur Yvette Cedex (France); Goffman, M. [Laboratoire d' Electronique Moleculaire, SPEC, Commissariat a l' Energie Atomique, Saclay F-91191, Gif sur Yvette Cedex (France); Bourgoin, J.-P. [Laboratoire d' Electronique Moleculaire, SPEC, Commissariat a l' Energie Atomique, Saclay F-91191, Gif sur Yvette Cedex (France)

    2006-12-15

    Carbon nanotube field-effect transistors (CN-FET) with a metallic back gate have been fabricated. By assembling a number of CNs in parallel, driving currents in the mA range have been obtained. The dynamic response of the CN-FETs has been investigated through S-parameters measurements. A current gain (|H {sub 21}|{sup 2}) cut-off frequency (f {sub t}) of 8 GHz, and a maximum stable gain (MSG) value of 10 dB at 1 GHz have been obtained. The extraction of an equivalent circuit is proposed.

  14. Probing top-gated field effect transistor of reduced graphene oxide monolayer made by dielectrophoresis

    OpenAIRE

    Vasu, K. S.; Chakraborty, Biswanath; Sampath, S.; Sood, A. K.

    2010-01-01

    We demonstrate top-gated field effect transistor made of reduced graphene oxide (RGO) monolayer (graphene) by dielectrophoresis. Raman spectrum of RGO flakes of typical size of 5{\\mu}m x 5{\\mu}m show a single 2D band at 2687 cm-1, characteristic of a single layer graphene. The two probe current - voltage measurements of RGO flakes, deposited in between the patterned electrodes with a gap of 2.5 {\\mu}m using a.c. dielectrophoresis show ohmic behavior with a resistance of ~ 37k{\\Omega}. The tem...

  15. High Electron Mobility Ge n-Channel Metal-Insulator-Semiconductor Field-Effect Transistors Fabricated by the Gate-Last Process with the Solid Source Diffusion Technique

    Science.gov (United States)

    Maeda, Tatsuro; Morita, Yukinori; Takagi, Shinichi

    2010-06-01

    We fabricate high-k/Ge n-channel metal-insulator-semiconductor field-effect transistors (MISFETs) by the gate-last process with the thermal solid source diffusion to achieve both of high quality source/drain (S/D) and gate stack. The n+/p junction formed by solid source diffusion technique of Sb dopant shows the excellent diode characteristics of ˜1.5×105 on/off ratio between +1 and -1 V and the quite low reverse current density of ˜4.1×10-4 A/cm2 at +1 V after the fabrication of high-k/Ge n-channel MISFETs that enable us to observe well-behaved transistor performances. The extracted electron mobility with the peak of 891 cm2/(V.s) is high enough to be superior to the Si universal electron mobility especially in low Eeff.

  16. Performance of pentacene-based organic field effect transistors using different polymer gate dielectrics

    Institute of Scientific and Technical Information of China (English)

    WU Ren-lei; CHENG Xiao-man; ZHENG Hong; YIN Shou-gen

    2009-01-01

    Pentacene-based organic field effect transistors (OFETs) are fabricated using poly(methyl methacrylate) (PMMA) and polyimide (PI) as gate dielectrics, respectively. The fabricated OFETs exhibit reasonable device characteristics. The field-effect mobility, threshold voltage, and on/off current radio are determined to be 3.214 × 10-2 cm2 / Vs, -28 V, and 1 × 103 respectively for OFETs with PMMA as gate dielectrics, and 7.306×10-3cm2 / Vs, -21 V, and 2 ×102 for OFETs with PI. Furthermore, the dielectric properties of gate insulator layer are tested and the dipole effect at the semiconductor/dielectrics interface is also analyzed by a model of energy level diagram.

  17. Dianthraceno[a,e]pentalenes: Synthesis, crystallographic structures and applications in organic field-effect transistors

    KAUST Repository

    Dai, Gaole

    2015-01-01

    Two soluble and stable dianthraceno[a,e]pentalenes with two (DAP1) and six (DAP2) phenyl substituents were synthesized. Both compounds possess a small energy band gap and show amphoteric redox behaviour due to intramolecular donor-accepter interactions. X-ray crystallographic analysis revealed that DAP2 has a closely packed structure with multi-dimensional [C-H⋯π] interactions although there are no π-π interactions between the dianthraceno[a,e]pentalene cores. As a result, solution-processed field effect transistors based on DAP2 exhibited an average hole mobility of 0.65 cm2 V-1 s-1. Under similar conditions, DAP1 showed an average field effect hole mobility of 0.001 cm2 V-1 s-1. This journal is

  18. In-situ doped junctionless polysilicon nanowires field effect transistors for low-cost biosensors

    DEFF Research Database (Denmark)

    Zulfiqar, Azeem; Patou, François; Pfreundt, Andrea

    2017-01-01

    Silicon nanowire (SiNW) field effect transistor based biosensors have already been proven to be a promising tool to detect biomolecules. However, the most commonly used fabrication techniques involve expensive Silicon-On-Insulator (SOI) wafers, E-beam lithography and ion-implantation steps....... In the work presented here, a top down approach to fabricate SiNW junctionless field effect biosensors using novel in-situ doped polysilicon is demonstrated. The p-type polysilicon is grown with an optimum boron concentration that gives a good metal-silicon electrical contact while maintaining the doping...... level at a low enough level to provide a good sensitivity for the biosensor. The silicon nanowires are patterned using standard photolithography and a wet etch method. The metal contacts are made from magnetron sputtered TiW and e-beam evaporation of gold. The passivation of electrodes has been done...

  19. Performance of Organic Field Effect Transistors with Self-Improved Cu/Organic Interfaces

    Institute of Scientific and Technical Information of China (English)

    HU Zi-Yang; CHENG Xiao-Man; WU Ren-Lei; WANG Zhong-Qiang; YIN Shou-Gen

    2009-01-01

    We fabricate pentacene-based organic field effect transistors (OFETs) with Cu as source and drain (S-D) electrodes.The fabricated devices stored for ten hours under ambient atmospheric conditions exhibit superior performance compared with the as-prepared devices.The field-effect mobility increases from 0.012 to 0.03 cm2 V-1 s-1,and the threshold voltage downshifts from -14 to -9 V.The on/off current ratios are close to the order of 104.The improved performance of the stored devices is attributed to the formation of thin Cu oxide at the Cu electrodes/organic interfaces.These results suggest a simple and available way to optimize device properties and to reduce fabrication cost for OFETs.

  20. Understanding charge transport in lead iodide perovskite thin-film field-effect transistors

    Science.gov (United States)

    Senanayak, Satyaprasad P.; Yang, Bingyan; Thomas, Tudor H.; Giesbrecht, Nadja; Huang, Wenchao; Gann, Eliot; Nair, Bhaskaran; Goedel, Karl; Guha, Suchi; Moya, Xavier; McNeill, Christopher R.; Docampo, Pablo; Sadhanala, Aditya; Friend, Richard H.; Sirringhaus, Henning

    2017-01-01

    Fundamental understanding of the charge transport physics of hybrid lead halide perovskite semiconductors is important for advancing their use in high-performance optoelectronics. We use field-effect transistors (FETs) to probe the charge transport mechanism in thin films of methylammonium lead iodide (MAPbI3). We show that through optimization of thin-film microstructure and source-drain contact modifications, it is possible to significantly minimize instability and hysteresis in FET characteristics and demonstrate an electron field-effect mobility (μFET) of 0.5 cm2/Vs at room temperature. Temperature-dependent transport studies revealed a negative coefficient of mobility with three different temperature regimes. On the basis of electrical and spectroscopic studies, we attribute the three different regimes to transport limited by ion migration due to point defects associated with grain boundaries, polarization disorder of the MA+ cations, and thermal vibrations of the lead halide inorganic cages. PMID:28138550

  1. Thienoacene-fused pentalenes: Syntheses, structures, physical properties and applications for organic field-effect transistors

    KAUST Repository

    Dai, Gaole

    2014-11-27

    Three soluble and stable thienoacene-fused pentalene derivatives (1-3) with different π-conjugation lengths were synthesized. X-ray crystallographic analysis and density functional theory (DFT) calculations revealed their unique geometric and electronic structures due to the interaction between the aromatic thienoacene units and antiaromatic pentalene moiety. As a result, they all possess a small energy gap and show amphoteric redox behaviour. Time dependent (TD) DFT calculations were used to explain their unique electronic absorption spectra. These new compounds exhibited good thermal stability and ordered packing in solid state and thus their applications in organic field-effect transistors (OFETs) were also investigated. The highest field-effect hole mobility of 0.016, 0.036 and 0.001 cm2 V-1 s-1 was achieved for solution-processed thin films of 1-3, respectively.

  2. Field-Effect Transistor Based on Si with LaAlO3-δ as the Source and Drain

    Institute of Scientific and Technical Information of China (English)

    YANG Fang; JIN Kui-Juan; LU Hui-Bin; HE Meng; YANG Guo-Zhen

    2009-01-01

    N-type LaAlO3-δ thin films are epitaxially grown on p-type Si substrates. An enhancement mode field-effect transistor is constructed with oxygen deficient LaAlO3-δ as the source and drain, p-type Si as the semJconducting channel, and SiO2 as the gate insulator, respectively. The typical current-voltage behavior with field-effect transistor characteristic is observed. The ON/OFF ratio reaches 14 at a gate voltage of 10 V, the field-effect mobility is 10cm2/V.s at a gate voltage of 2 V, and the transconductance is 5 × 10-6 A/V at a drain-source voltage of 0.8 V at room temperature. The present field-effect transistor device demonstrates the possibility of realizing the integration of multifunctional perovskite oxides and the conventional Si semiconductor.

  3. Silicon on ferroelectic insulator field effect transistor (SOF-FET) a new device for the next generation ultra low power circuits

    Science.gov (United States)

    Es-Sakhi, Azzedin D.

    concept of negative capacitance. The new field effect transistor (FET) based on ferroelectric insulator named Silicon-On-Ferroelectric Insulator Field Effect Transistor (SOF-FET). This proposal is a promising methodology for future ultra-low-power applications, because it demonstrates the ability to replace the silicon-bulk based MOSFET, and offers subthreshold swing significantly lower than 60mV/decade and reduced threshold voltage to form a conducting channel. The SOF-FET can also solve the issue of junction leakage (due to the presence of unipolar junction between the top plate of the negative capacitance and the diffused areas that form the transistor source and drain). In this device the charge hungry ferroelectric film already limits the leakage.

  4. Coupling between electrolyte and organic semiconductor in electrolyte-gated organic field effect transistors (Conference Presentation)

    Science.gov (United States)

    Biscarini, Fabio; Di Lauro, Michele; Berto, Marcello; Bortolotti, Carlo A.; Geerts, Yves H.; Vuillaume, Dominique

    2016-11-01

    Organic field effect transistors (OFET) operated in aqueous environments are emerging as ultra-sensitive biosensors and transducers of electrical and electrochemical signals from a biological environment. Their applications range from detection of biomarkers in bodily fluids to implants for bidirectional communication with the central nervous system. They can be used in diagnostics, advanced treatments and theranostics. Several OFET layouts have been demonstrated to be effective in aqueous operations, which are distinguished either by their architecture or by the respective mechanism of doping by the ions in the electrolyte solution. In this work we discuss the unification of the seemingly different architectures, such as electrolyte-gated OFET (EGOFET), organic electrochemical transistor (OECT) and dual-gate ion-sensing FET. We first demonstrate that these architectures give rise to the frequency-dependent response of a synapstor (synapse-like transistor), with enhanced or depressed modulation of the output current depending on the frequency of the time-dependent gate voltage. This behavior that was reported for OFETs with embedded metal nanoparticles shows the existence of a capacitive coupling through an equivalent network of RC elements. Upon the systematic change of ions in the electrolyte and the morphology of the charge transport layer, we show how the time scale of the synapstor is changed. We finally show how the substrate plays effectively the role of a second bottom gate, whose potential is actually fixed by the pH/composition of the electrolyte and the gate voltage applied.

  5. High capacitance organic field-effect transistors with modified gate insulator surface

    Science.gov (United States)

    Majewski, L. A.; Schroeder, R.; Grell, M.; Glarvey, P. A.; Turner, M. L.

    2004-11-01

    In this paper, we report on flexible, high capacitance, pentacene, and regioregular poly(3-hexylthiophene) (rr-P3HT) organic field-effect transistors fabricated on metallized Mylar films. The gate insulator, Al2O3, was prepared by means of anodization. We show that covering the anodized gate insulator with an octadecyltrichlorosilane self-assembled monolayer or apoly(α-methylstyrene) capping layer has the same effect on carrier mobility as for thermally grown silicon oxide. In addition, temperature-dependent measurements of mobility were performed on transistors fabricated with and without modification of the gate dielectric. In the case of both the pentacene and the rr-P3HT transistors, the μ(T ) behavior shows that the cause of the mobility enhancement through surface modification is not a reduction in the level of energetic disorder (σ in Bässler's model), as in the case of the fully amorphous organic semiconductor poly(triarylamine) [Veres et al., Adv. Funct. Mater. 13, 199 (2003)]. It appears that the surface modification improves mobility by changing the morphology of the semiconducting films.

  6. Memristive device based on a depletion-type SONOS field effect transistor

    Science.gov (United States)

    Himmel, N.; Ziegler, M.; Mähne, H.; Thiem, S.; Winterfeld, H.; Kohlstedt, H.

    2017-06-01

    State-of-the-art SONOS (silicon-oxide-nitride-oxide-polysilicon) field effect transistors were operated in a memristive switching mode. The circuit design is a variation of the MemFlash concept and the particular properties of depletion type SONOS-transistors were taken into account. The transistor was externally wired with a resistively shunted pn-diode. Experimental current-voltage curves show analog bipolar switching characteristics within a bias voltage range of ±10 V, exhibiting a pronounced asymmetric hysteresis loop. The experimental data are confirmed by SPICE simulations. The underlying memristive mechanism is purely electronic, which eliminates an initial forming step of the as-fabricated cells. This fact, together with reasonable design flexibility, in particular to adjust the maximum R ON/R OFF ratio, makes these cells attractive for neuromorphic applications. The relative large set and reset voltage around ±10 V might be decreased by using thinner gate-oxides. The all-electric operation principle, in combination with an established silicon manufacturing process of SONOS devices at the Semiconductor Foundry X-FAB, promise reliable operation, low parameter spread and high integration density.

  7. Gate-Sensing Coherent Charge Oscillations in a Silicon Field-Effect Transistor.

    Science.gov (United States)

    Gonzalez-Zalba, M Fernando; Shevchenko, Sergey N; Barraud, Sylvain; Johansson, J Robert; Ferguson, Andrew J; Nori, Franco; Betz, Andreas C

    2016-03-09

    Quantum mechanical effects induced by the miniaturization of complementary metal-oxide-semiconductor (CMOS) technology hamper the performance and scalability prospects of field-effect transistors. However, those quantum effects, such as tunneling and coherence, can be harnessed to use existing CMOS technology for quantum information processing. Here, we report the observation of coherent charge oscillations in a double quantum dot formed in a silicon nanowire transistor detected via its dispersive interaction with a radio frequency resonant circuit coupled via the gate. Differential capacitance changes at the interdot charge transitions allow us to monitor the state of the system in the strong-driving regime where we observe the emergence of Landau-Zener-Stückelberg-Majorana interference on the phase response of the resonator. A theoretical analysis of the dispersive signal demonstrates that quantum and tunneling capacitance changes must be included to describe the qubit-resonator interaction. Furthermore, a Fourier analysis of the interference pattern reveals a charge coherence time, T2 ≈ 100 ps. Our results demonstrate charge coherent control and readout in a simple silicon transistor and open up the possibility to implement charge and spin qubits in existing CMOS technology.

  8. Charge injection in solution-processed organic field-effect transistors: physics, models and characterization methods.

    Science.gov (United States)

    Natali, Dario; Caironi, Mario

    2012-03-15

    A high-mobility organic semiconductor employed as the active material in a field-effect transistor does not guarantee per se that expectations of high performance are fulfilled. This is even truer if a downscaled, short channel is adopted. Only if contacts are able to provide the device with as much charge as it needs, with a negligible voltage drop across them, then high expectations can turn into high performances. It is a fact that this is not always the case in the field of organic electronics. In this review, we aim to offer a comprehensive overview on the subject of current injection in organic thin film transistors: physical principles concerning energy level (mis)alignment at interfaces, models describing charge injection, technologies for interface tuning, and techniques for characterizing devices. Finally, a survey of the most recent accomplishments in the field is given. Principles are described in general, but the technologies and survey emphasis is on solution processed transistors, because it is our opinion that scalable, roll-to-roll printing processing is one, if not the brightest, possible scenario for the future of organic electronics. With the exception of electrolyte-gated organic transistors, where impressively low width normalized resistances were reported (in the range of 10 Ω·cm), to date the lowest values reported for devices where the semiconductor is solution-processed and where the most common architectures are adopted, are ∼10 kΩ·cm for transistors with a field effect mobility in the 0.1-1 cm(2)/Vs range. Although these values represent the best case, they still pose a severe limitation for downscaling the channel lengths below a few micrometers, necessary for increasing the device switching speed. Moreover, techniques to lower contact resistances have been often developed on a case-by-case basis, depending on the materials, architecture and processing techniques. The lack of a standard strategy has hampered the progress of the

  9. Plasmon field effect transistor: A novel sensing platform for biomedical applications

    Science.gov (United States)

    Shokri Kojori, Hossein

    The interest in plasmons, associated with nanostructured metals, has remarkably increased in the past decade. A Recent improvement in fabrication techniques to create well-controlled nanostructures also contributed to the rapid development of plasmonic applications, such as meta-materials, nonlinear optics, photovoltaic devices, biomedical sensors, medical therapies and spectroscopy. The surface plasmon resonance (SPR) sensor is one of the successful applications, which is widely used in biomedical research. On the other hand, localized surface plasmon resonance (LSPR) is also widely studied in a broad range of applications. The distinct property of LSPR is a tailored and sharp absorption/scattering peaks depending on the shape and sizes of the metal nanostructures. In addition, plasmonics can enable integration of high speed optical circuit by taking the advantages from the current electronics and optics technologies. Thus, plasmonics is considered as a solution for the next generation systems that offers ultra-high speed data processing. In this dissertation, we will introduce a novel plasmon field effect transistor (FET) that enables direct detection and efficient amplification of plasmon energy. This FET has several advantages such as electrical isolation of plasmon absorber nanostructures from a sensing and drug screening. Currently, we have proof of concept for the antigen-antibody bonding using the plasmon field effect transistor. We will develop a multiplexing capable plasmon FET sensing platform by integrating an array of plasmon FETs with microfluidic channels to detect cancer biomarkers.

  10. Utilizing self-assembled-monolayer-based gate dielectrics to fabricate molybdenum disulfide field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Kawanago, Takamasa, E-mail: kawanago.t.ab@m.titech.ac.jp; Oda, Shunri [Quantum Nanoelectronics Research Center (QNERC), Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo, 152-8550 (Japan)

    2016-01-25

    In this study, we apply self-assembled-monolayer (SAM)-based gate dielectrics to the fabrication of molybdenum disulfide (MoS{sub 2}) field-effect transistors. A simple fabrication process involving the selective formation of a SAM on metal oxides in conjunction with the dry transfer of MoS{sub 2} flakes was established. A subthreshold slope (SS) of 69 mV/dec and no hysteresis were demonstrated with the ultrathin SAM-based gate dielectrics accompanied by a low gate leakage current. The small SS and no hysteresis indicate the superior interfacial properties of the MoS{sub 2}/SAM structure. Cross-sectional transmission electron microscopy revealed a sharp and abrupt interface of the MoS{sub 2}/SAM structure. The SAM-based gate dielectrics are found to be applicable to the fabrication of low-voltage MoS{sub 2} field-effect transistors and can also be extended to various layered semiconductor materials. This study opens up intriguing possibilities of SAM-based gate dielectrics in functional electronic devices.

  11. Environmental Effects on Hysteresis of Transfer Characteristics in Molybdenum Disulfide Field-Effect Transistors.

    Science.gov (United States)

    Shimazu, Yoshihiro; Tashiro, Mitsuki; Sonobe, Satoshi; Takahashi, Masaki

    2016-07-20

    Molybdenum disulfide (MoS2) has recently received much attention for nanoscale electronic and photonic applications. To explore the intrinsic properties and enhance the performance of MoS2-based field-effect transistors, thorough understanding of extrinsic effects such as environmental gas and contact resistance of the electrodes is required. Here, we report the effects of environmental gases on the transport properties of back-gated multilayered MoS2 field-effect transistors. Comparisons between different gases (oxygen, nitrogen, and air and nitrogen with varying relative humidities) revealed that water molecules acting as charge-trapping centers are the main cause of hysteresis in the transfer characteristics. While the hysteresis persisted even after pumping out the environmental gas for longer than 10 h at room temperature, it disappeared when the device was cooled to 240 K, suggesting a considerable increase in the time constant of the charge trapping/detrapping at these modestly low temperatures. The suppression of the hysteresis or instability in the easily attainable temperature range without surface passivation is highly advantageous for the device application of this system. The humidity dependence of the threshold voltages in the transfer curves indicates that the water molecules dominantly act as hole-trapping centers. A strong dependence of the on-state current on oxygen pressure was also observed.

  12. The interface between ferroelectric and 2D material for a Ferroelectric Field-Effect Transistor

    Science.gov (United States)

    Park, Nahee; Kang, Haeyong; Lee, Sang-Goo; Lee, Young Hee; Suh, Dongseok

    We have studied electrical property of ferroelectric field-effect transistor which consists of graphene on hexagonal Boron-Nitride (h-BN) gated by a ferroelectric, PMN-PT (i.e. (1-x)Pb(Mg1/3Nb2/3) O3-xPbTiO3) single-crystal substrate. The PMN-PT was expected to have an effect on polarization field into the graphene channel and to induce a giant amount of surface charge. The hexagonal Boron-Nitride (h-BN) flake was directly exfoliated on the PMN-PT substrate for preventing graphene from directly contacting on the PMN-PT substrate. It can make us to observe the effect of the interface between ferroelectric and 2D material on the device operation. Monolayer graphene as 2D channel material, which was confirmed by Raman spectroscopy, was transferred on top of the hexagonal Boron-Nitride (h-BN) by using the conventional dry-transfer method. Here, we can demonstrate that the structure of graphene/hexagonal-BN/ferroelectric field-effect transistor makes us to clearly understand the device operation as well as the interface between ferroelectric and 2D materials by inserting h-BN between them. The phenomena such as anti-hysteresis, current saturation behavior, and hump-like increase of channel current, will be discussed by in terms of ferroelectric switching, polarization-assisted charge trapping.

  13. Band gap engineered nano perforated graphene microstructures for field effect transistor

    Science.gov (United States)

    Palla, Penchalaiah; Tiwari, Durgesh Laxman; Ansari, Hasan Raza; Babu, Taraprasanna Saha; Ethiraj, Anita Sagadevan; Raina, J. P.

    2016-05-01

    To make use of exceptional properties of graphene in Field effect Transistor (FETs) for switching devices a band gap must be introduced in order to switch -off the device. Through periodic nano perforations a semi-metallic graphene is converted into semiconducting graphene. To understand the device physics behind the reported experiments theoretical simulations has been carried out. The present paper illustrates nano perforated semiconducting graphene Field effect Transistor (FETs) with micron scale dimensions. The simulation has been performed using drift-diffusion semi-classical and tight-binding based non-equilibrium green's function (NEGF) methods. The obtained simulation results are compared with previously reported experimental work. The device dimensions considered for simulations and the experiment are similar with neck width, hole periodicity and channel length of 6.3 nm, 16.3 nm and 1 µm respectively. The interesting and new finding in this work is the p-type I-V characteristics for small band gap devices and n-type behavior for large band gap devices.

  14. Metal oxide-graphene field-effect transistor: interface trap density extraction model

    Directory of Open Access Journals (Sweden)

    Faraz Najam

    2016-09-01

    Full Text Available A simple to implement model is presented to extract interface trap density of graphene field effect transistors. The presence of interface trap states detrimentally affects the device drain current–gate voltage relationship Ids–Vgs. At the moment, there is no analytical method available to extract the interface trap distribution of metal-oxide-graphene field effect transistor (MOGFET devices. The model presented here extracts the interface trap distribution of MOGFET devices making use of available experimental capacitance–gate voltage Ctot–Vgs data and a basic set of equations used to define the device physics of MOGFET devices. The model was used to extract the interface trap distribution of 2 experimental devices. Device parameters calculated using the extracted interface trap distribution from the model, including surface potential, interface trap charge and interface trap capacitance compared very well with their respective experimental counterparts. The model enables accurate calculation of the surface potential affected by trap charge. Other models ignore the effect of trap charge and only calculate the ideal surface potential. Such ideal surface potential when used in a surface potential based drain current model will result in an inaccurate prediction of the drain current. Accurate calculation of surface potential that can later be used in drain current model is highlighted as a major advantage of the model.

  15. Simulation of field-effect transistors and resonant tunneling diodes based on graphene

    Science.gov (United States)

    Abramov, Igor I.; Labunov, Vladimir A.; Kolomejtseva, Natali V.; Romanova, Irina A.

    2016-12-01

    Graphene is a nanomaterial that due to unique properties has attracted great interest for various applications, in particular, for development of nanoelectronic devices. In the paper the graphene field-effect transistors (GFET) and resonant tunneling diodes (RTD) are analyzed with the use of proposed models. First, simulation of dual-gate field-effect transistor based on monolayer graphene with the use of proposed combined model is considered. In the model the following important factors such as quantum capacitance, hole and electron mobility difference, drain and source resistances are taken into account. Investigations of dependence of a drain current on drain voltage for various top-gate-to-source voltages are performed. Influence of channel length, source and drain resistances on output characteristics of the device is analyzed. Comparison of calculation results with simulation ones obtained with the known models was carried out. Secondly, simulation of graphene-based nanostructures on hexagonal boron nitride, silicon carbide and silicon dioxide substrates was performed using proposed self-consistent numerical model, based on effective wave function formalism. The developed models in detail were described in our previous works. The possibility of using a proposed self-consistent model for double- and triple-barrier graphene-based RTD simulation was illustrated. As well as it was investigated the influence of different parameters on IV-characteristics of graphene-based RTDs. It was shown that it is necessary to take into account extended (passive) regions for adequate simulation of these devices.

  16. Impact of Scaling Gate Insulator Thickness on the Performance of Carbon Nanotube Field Effect Transistors (CNTFETs

    Directory of Open Access Journals (Sweden)

    Devi Dass

    2013-05-01

    Full Text Available As scaling down Si MOSFET devices degrade device performance in terms of short channel effects. Carbon nanotube field effect transistor (CNTFET is one of the novel nanoelectronics devices that overcome those MOSFET limitations. The carbon nanotube field effect transistors (CNTFETs have been explored and proposed to be the promising candidate for the next generation of integrated circuit (IC devices. To explore the role of CNTFETs in future integrated circuits, it is important to evaluate their performance. However, to do that we need a model that can accurately describe the behavior of the CNTFETs so that the design and evaluation of circuits using these devices can be made. In this paper, we have investigated the effect of scaling gate insulator thickness on the device performance of cylindrical shaped ballistic CNTFET in terms of transfer characteristics, output characteristics, average velocity, gm/Id ratio, mobile charge, quantum capacitance/insulator capacitance, drive current (Ion, Ion / Ioff ratio, transconductance, and output conductance. We concluded that the device metrics such as Ion, Ion / Ioff ratio, transconductance, and output conductance increases with the decrease in gate insulator thickness. Also, we concluded that the gate insulator thickness reduction causes subthreshold slope close to the theoretical limit of 60 mV/decade and DIBL close to zero at room temperature.

  17. Temperature sensitivity analysis of polarity controlled electrostatically doped tunnel field-effect transistor

    Science.gov (United States)

    Nigam, Kaushal; Pandey, Sunil; Kondekar, P. N.; Sharma, Dheeraj

    2016-09-01

    The conventional tunnel field-effect transistors (TFETs) have shown potential to scale down in sub-22 nm regime due to its lower sub-threshold slope and robustness against short-channel effects (SCEs), however, sensitivity towards temperature variation is a major concern. Therefore, for the first time, we investigate temperature sensitivity analysis of a polarity controlled electrostatically doped tunnel field-effect transistor (ED-TFET). Different performance metrics and analog/RF figure-of-merits were considered and compared for both devices, and simulations were performed using Silvaco ATLAS device tool. We found that the variation in ON-state current in ED-TFET is almost temperature independent due to electrostatically doped mechanism, while, it increases in conventional TFET at higher temperature. Above room temperature, the variation in ION, IOFF, and SS sensitivity in ED-TFET are only 0.11%/K, 2.21%/K, and 0.63%/K, while, in conventional TFET the variations are 0.43%/K, 2.99%/K, and 0.71%/K, respectively. However, below room temperature, the variation in ED-TFET ION is 0.195%/K compared to 0.27%/K of conventional TFET. Moreover, it is analysed that the incomplete ionization effect in conventional TFET severely affects the drive current and the threshold voltage, while, ED-TFET remains unaffected. Hence, the proposed ED-TFET is less sensitive towards temperature variation and can be used for cryogenics as well as for high temperature applications.

  18. Deep-submicron Graphene Field-Effect Transistors with State-of-Art fmax

    Science.gov (United States)

    Lyu, Hongming; Lu, Qi; Liu, Jinbiao; Wu, Xiaoming; Zhang, Jinyu; Li, Junfeng; Niu, Jiebin; Yu, Zhiping; Wu, Huaqiang; Qian, He

    2016-10-01

    In order to conquer the short-channel effects that limit conventional ultra-scale semiconductor devices, two-dimensional materials, as an option of ultimate thin channels, receive wide attention. Graphene, in particular, bears great expectations because of its supreme carrier mobility and saturation velocity. However, its main disadvantage, the lack of bandgap, has not been satisfactorily solved. As a result, maximum oscillation frequency (fmax) which indicates transistors’ power amplification ability has been disappointing. Here, we present submicron field-effect transistors with specially designed low-resistance gate and excellent source/drain contact, and therefore significantly improved fmax. The fabrication was assisted by the advanced 8-inch CMOS back-end-of-line technology. A 200-nm-gate-length GFET achieves fT/fmax = 35.4/50 GHz. All GFET samples with gate lengths ranging from 200 nm to 400 nm possess fmax 31–41% higher than fT, closely resembling Si n-channel MOSFETs at comparable technology nodes. These results re-strengthen the promise of graphene field-effect transistors in next generation semiconductor electronics.

  19. Strain-induced modulation on phonon and electronic properties of suspended black phosphorus field effect transistor

    Science.gov (United States)

    Zheng, Bo; Si, Naichao; Xie, Guoxin; Wang, Quan

    2017-02-01

    Black phosphorus has recently appeared as a promising two-dimensional material for applications in high performance nanoelectronics. Its single- and few-atomic layer forms in field-effect transistors have attracted a lot of attention due to the tunable bandgap (0.3-2.0 eV), high carrier mobility (1000 cm2 V-1 s-1) and decent on-off ratios (105). Here, we demonstrate a suspended black phosphorus field effect transistor (BP-FET) and utilize Raman spectroscope to characterize the strain on the effects of Raman phonon. We find that red shifts appear in all the three vibrational modes (Ag1 , B2g and Ag2) in different degrees. Among them, Ag1 mode is most sensitive to the tensile strain. We further investigate the electronic properties with a Cascade semi-automatic probe station. The linear relationships in the output curves indicate the contacts between black phosphorus and electrodes are ohmic contacts. The transfer characteristic curves declare the drain current modulation is ∼ 7.6 ×103 for the hole conduction and ∼57 for the electron conduction. Mobility of this device is found to be 347.5 cm2 V-1 s-1 and 4.9 cm2 V-1 s-1 for the hole and electron conduction, respectively. These results provide a theoretical basis for the coordination of high-performance black phosphorus electronic components.

  20. Biosensors based on enzyme field-effect transistors for determination of some substrates and inhibitors.

    Science.gov (United States)

    Dzyadevych, Sergei V; Soldatkin, Alexey P; Korpan, Yaroslav I; Arkhypova, Valentyna N; El'skaya, Anna V; Chovelon, Jean-Marc; Martelet, Claude; Jaffrezic-Renault, Nicole

    2003-10-01

    This paper is a review of the authors' publications concerning the development of biosensors based on enzyme field-effect transistors (ENFETs) for direct substrates or inhibitors analysis. Such biosensors were designed by using immobilised enzymes and ion-selective field-effect transistors (ISFETs). Highly specific, sensitive, simple, fast and cheap determination of different substances renders them as promising tools in medicine, biotechnology, environmental control, agriculture and the food industry. The biosensors based on ENFETs and direct enzyme analysis for determination of concentrations of different substrates (glucose, urea, penicillin, formaldehyde, creatinine, etc.) have been developed and their laboratory prototypes were fabricated. Improvement of the analytical characteristics of such biosensors may be achieved by using a differential mode of measurement, working solutions with different buffer concentrations and specific agents, negatively or positively charged additional membranes, or genetically modified enzymes. These approaches allow one to decrease the effect of the buffer capacity influence on the sensor response in an aim to increase the sensitivity of the biosensors and to extend their dynamic ranges. Biosensors for the determination of concentrations of different toxic substances (organophosphorous pesticides, heavy metal ions, hypochlorite, glycoalkaloids, etc.) were designed on the basis of reversible and/or irreversible enzyme inhibition effect(s). The conception of an enzymatic multibiosensor for the determination of different toxic substances based on the enzyme inhibition effect is also described. We will discuss the respective advantages and disadvantages of biosensors based on the ENFETs developed and also demonstrate their practical application.

  1. Diazaisoindigo bithiophene and terthiophene copolymers for application in field-effect transistors and solar cells

    KAUST Repository

    Yue, Wan

    2017-06-10

    Two donor–acceptor conjugated polymers with azaisoindigo as acceptor units and bithiophene and terthiophene as donor units have been synthesized by Stille polymerization. These two polymers have been successfully applied in field-effect transistors and polymer solar cells. By changing the donor component of the conjugated polymer backbone from bithiophene to terthiophene, the density of thiophene in the backbone is increased, manifesting as a decrease in both ionization potential and in electron affinity. Therefore, the charge transport in field-effect transistors switches from ambipolar to predominantly hole transport behavior. PAIIDTT exhibits hole mobility up to 0.40 cm2/Vs and electron mobility of 0.02 cm2/Vs, whereas PAIIDTTT exhibits hole mobility of 0.62 cm2/Vs. Polymer solar cells were fabricated based on these two polymers as donors with PC61BM and PC71BM as acceptor where PAIIDTT shows a modest efficiency of 2.57% with a very low energy loss of 0.55 eV, while PAIIDTTT shows a higher efficiency of 6.16% with a higher energy loss of 0.74 eV. Our results suggest that azaisoindgo is a useful building block for the development of efficient polymer solar cells with further improvement possibility by tuning the alternative units on the polymer backbone. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017

  2. A Micro-Machined Microphone Based on a Combination of Electret and Field-Effect Transistor.

    Science.gov (United States)

    Shin, Kumjae; Jeon, Junsik; West, James Edward; Moon, Wonkyu

    2015-08-18

    Capacitive-type transduction is now widely used in MEMS microphones. However, its sensitivity decreases with reducing size, due to decreasing air gap capacitance. In the present study, we proposed and developed the Electret Gate of Field Effect Transistor (ElGoFET) transduction based on an electret and FET (field-effect-transistor) as a novel mechanism of MEMS microphone transduction. The ElGoFET transduction has the advantage that the sensitivity is dependent on the ratio of capacitance components in the transduction structure. Hence, ElGoFET transduction has high sensitivity even with a smaller air gap capacitance, due to a miniaturization of the transducer. A FET with a floating-gate electrode embedded on a membrane was designed and fabricated and an electret was fabricated by ion implantation with Ga(+) ions. During the assembly process between the FET and the electret, the operating point of the FET was characterized using the static response of the FET induced by the electric field due to the trapped positive charge at the electret. Additionally, we evaluated the microphone performance of the ElGoFET by measuring the acoustic response in air using a semi-anechoic room. The results confirmed that the proposed transduction mechanism has potential for microphone applications.

  3. Selenium-Containing Fused Bicyclic Heterocycle Diselenolodiselenole: Field Effect Transistor Study and Structure-Property Relationship.

    Science.gov (United States)

    Debnath, Sashi; Chithiravel, Sundaresan; Sharma, Sagar; Bedi, Anjan; Krishnamoorthy, Kothandam; Zade, Sanjio S

    2016-07-20

    The first application of the diselenolodiselenole (C4Se4) heterocycle as an active organic field effect transistor materials is demonstrated here. C4Se4 derivatives (2a-2d) were obtained by using a newly developed straightforward diselenocyclization protocol, which includes the reaction of diynes with selenium powder at elevated temperature. C4Se4 derivatives exhibit strong donor characteristics and planar structure (except 2d). The atomic force microscopic analysis and thin-film X-ray diffraction pattern of compounds 2a-2d indicated the formation of distinct crystalline films that contain large domains. A scanning electron microscopy study of compound 2b showed development of symmetrical grains with an average diameter of 150 nm. Interestingly, 2b exhibited superior hole mobility, approaching 0.027 cm(2) V(-1) s(-1) with a transconductance of 9.2 μS. This study correlate the effect of π-stacking, Se···Se intermolecular interaction, and planarity with the charge transport properties and performance in the field effect transistor devices. We have shown that the planarity in C4Se4 derivatives was achieved by varying the end groups attached to the C4Se4 core. In turn, optoelectronic properties can also be tuned for all these derivatives by end-group variation.

  4. Probing top-gated field effect transistor of reduced graphene oxide monolayer made by dielectrophoresis

    Science.gov (United States)

    Vasu, K. S.; Chakraborty, Biswanath; Sampath, S.; Sood, A. K.

    2010-08-01

    We demonstrate a top-gated field effect transistor made of a reduced graphene oxide (RGO) monolayer (graphene) by dielectrophoresis. The Raman spectrum of RGO flakes of typical size of 5 μm×5 μm shows a single 2D band at 2687 cm -1, characteristic of single-layer graphene. The two-probe current-voltage measurements of RGO flakes, deposited in between the patterned electrodes with a gap of 2.5 μm using ac dielectrophoresis, show ohmic behavior with a resistance of ˜37 kΩ. The temperature dependence of the resistance (R) of RGO measured between 305 K and 393 K yields a temperature coefficient of resistance [dR/dT]/R˜-9.5×10-4/K, the same as that of mechanically exfoliated single-layer graphene. The field-effect transistor action was obtained by electrochemical top-gating using a solid polymer electrolyte (PEO+LiClO 4) and Pt wire. The ambipolar nature of graphene flakes is observed up to a doping level of ˜6×1012/cm and carrier mobility of ˜50 cm 2/V s. The source-drain current characteristics show a tendency of current saturation at high source-drain voltage which is analyzed quantitatively by a diffusive transport model.

  5. Neutron Radiation Effect On 2N2222 And NTE 123 NPN Silicon Bipolar Junction Transistors

    Science.gov (United States)

    Oo, Myo Min; Rashid, N. K. A. Md; Karim, J. Abdul; Zin, M. R. Mohamed; Hasbullah, N. F.

    2013-12-01

    This paper examines neutron radiation with PTS (Pneumatic Transfer System) effect on silicon NPN bipolar junction transistors (2N2222 and NTE 123) and analysis of the transistors in terms of electrical characterization such as current gain after neutron radiation. The key parameters are measured with Keithley 4200SCS. Experiment results show that the current gain degradation of the transistors is very sensitive to neutron radiation. The neutron radiation can cause displacement damage in the bulk layer of the transistor structure. The current degradation is believed to be governed by increasing recombination current between the base and emitter depletion region.

  6. Performance improvement in novel germanium-tin/germanium heterojunction-enhanced p-channel tunneling field-effect transistor

    Science.gov (United States)

    Wang, Hongjuan; Liu, Yan; Liu, Mingshan; Zhang, Qingfang; Zhang, Chunfu; Ma, Xiaohua; Zhang, Jincheng; Hao, Yue; Han, Genquan

    2015-07-01

    We design a novel GeSn-based heterojunction-enhanced p-channel tunneling field-effect transistor (HE-PTFET) with a Ge0.92Sn0.08/Ge heterojunction located in channel region, at a distance of LT-H from the Ge0.92Sn0.08 source-channel tunneling junction (TJ). HE-PTFETs demonstrate the negative shift of onset voltage VONSET, the steeper subthreshold swing S, and the improved on-state current ION compared to Ge0.92Sn0.08 homo-PTFET. At low VGS, the suppression of BTBT due to the widening of the tunneling barrier caused by the heterojunction leads to a negative shift of VONSET in HE-PTFETs. At high VGS, ION enhancement in HE-PTFETs is achieved over the homo device, which is attributed to the confinement of BTBT in Ge0.92Sn0.08 source-channel TJ region by the heterojunction, where the short tunneling paths lead to a high tunneling probability. Due to the steeper average S, HE-PTFET with a 6 nm LT-H achieves a 4 times higher ION compared to homo device at a VDD of -0.3 V.

  7. Performance analysis of InGaAs/GaAsP heterojunction double gate tunnel field effect transistor

    Science.gov (United States)

    Ahish, S.; Sharma, Dheeraj; Vasantha, M. H.; Kumar, Y. B. N.

    2017-03-01

    In this paper, analog/RF performance of InGaAs/GaAsP heterojunction double gate tunnel field effect transistor (HJTFET) has been explored. A highly doped n+ layer is placed at the Source-Channel junction in order to improve the horizontal electric field component and thus, improve the realiability of the device. The analog performance of the device is analysed by extracting current-voltage characteristics, transcondutance (gm), gate-to-drain capacitance (Cgd) and gate-to-source capacitance (Cgs). Further, RF performance of the device is evaluated by obtaining cut-off frequency (fT) and Gain Bandwidth (GBW) product. ION /IOFF ratio equal to ≈ 109, subthreshold slope of 27 mV/dec, maximum fT of 2.1 THz and maximum GBW of 484 GHz were achieved. Also, the impact of temperature variation on the linearity performance of the device has been investigated. Furthermore, the circuit level performance of the device is performed by implementing a Common Source (CS) amplifier; maximum gain of 31.11 dB and 3-dB cut-off frequency equal to 91.2 GHz were achieved for load resistance (RL) = 17.5 KΩ.

  8. Terahertz signal detection in a short gate length field-effect transistor with a two-dimensional electron gas

    Energy Technology Data Exchange (ETDEWEB)

    Vostokov, N. V., E-mail: vostokov@ipm.sci-nnov.ru; Shashkin, V. I. [Institute for Physics of Microstructures of the Russian Academy of Sciences, 603950 Nizhny Novgorod, Russia and N. I. Lobachevsky State University of Nizhny Novgorod, 603950 Nizhny Novgorod (Russian Federation)

    2015-11-28

    We consider the problem of non-resonant detection of terahertz signals in a short gate length field-effect transistor having a two-dimensional electron channel with zero external bias between the source and the drain. The channel resistance, gate-channel capacitance, and quadratic nonlinearity parameter of the transistor during detection as a function of the gate bias voltage are studied. Characteristics of detection of the transistor connected in an antenna with real impedance are analyzed. The consideration is based on both a simple one-dimensional model of the transistor and allowance for the two-dimensional distribution of the electric field in the transistor structure. The results given by the different models are discussed.

  9. Detection of terahertz radiation by tightly concatenated InGaAs field-effect transistors integrated on a single chip

    Energy Technology Data Exchange (ETDEWEB)

    Popov, V. V., E-mail: popov-slava@yahoo.co.uk [Kotelnikov Institute of Radio Engineering and Electronics (Saratov Branch), Russian Academy of Sciences, Saratov 410019 (Russian Federation); Yermolaev, D. M.; Shapoval, S. Yu. [Institute of Microelectronic Technology and High-Purity Materials, Russian Academy of Sciences, Chernogolovka, Moscow Region 142432 (Russian Federation); Maremyanin, K. V.; Gavrilenko, V. I. [Institute for Physics of Microstructures, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University of Nizhni Novgorod, Nizhni Novgorod 603950 (Russian Federation); Zemlyakov, V. E.; Bespalov, V. A.; Yegorkin, V. I. [National Research University of Electronic Technology, Zelenograd, Moscow 124498 (Russian Federation); Maleev, N. A.; Ustinov, V. M. [Ioffe Physical Technical Institute, Russian Academy of Sciences, St. Petersburg 194021 (Russian Federation)

    2014-04-21

    A tightly concatenated chain of InGaAs field-effect transistors with an asymmetric T-gate in each transistor demonstrates strong terahertz photovoltaic response without using supplementary antenna elements. We obtain the responsivity above 1000 V/W and up to 2000 V/W for unbiased and drain-biased transistors in the chain, respectively, with the noise equivalent power below 10{sup −11} W/Hz{sup 0.5} in the unbiased mode of the detector operation.

  10. Unified description of potential profiles and electrical transport in unipolar and ambipolar organic field-effect transistors

    Science.gov (United States)

    Smits, Edsger C. P.; Mathijssen, Simon G. J.; Cölle, Michael; Mank, Arjan J. G.; Bobbert, Peter A.; Blom, Paul W. M.; de Boer, Bert; de Leeuw, Dago M.

    2007-09-01

    Validation of models for charge transport in organic transistors is fundamentally important for their technological use. Usually current-voltage measurements are performed to investigate organic transistors. In situ scanning Kelvin probe microscopy measurements provide a powerful complementary technique to distinguish between models based on band and hopping transports. We perform combined current-voltage and Kelvin probe microscopy measurements on unipolar and ambipolar organic field-effect transistors. We demonstrate that by this combination we can stringently test these two different transport models and come up with a unified description of charge transport in disordered organic semiconductors.

  11. Analytical model of carrier mobility in a Polymer Field Effect Transistor

    Directory of Open Access Journals (Sweden)

    Milošević Milan M.

    2007-01-01

    Full Text Available In this paper, the carrier mobility analytical model in a POFET (Polymer Field Effect Transistor channel is proposed. The model was developed on the basis of existing models and experimental results. The proposed model is universal because it encompasses the carrier mobility dependence on temperature, electric field and trap density in the POFET channel. The model is comparatively simple, easy for application and gives valuable results. According to the presented model, simulations of mobility as a function of the parameters of interest were performed. The obtained results are shown graphically. In comparison to accessible experimental results excellent correspondence was found. This model enables the calculation of simple POFET current-voltage I (V characteristics.

  12. Selective functionalization and loading of biomolecules in crystalline silicon nanotube field-effect-transistors.

    Science.gov (United States)

    Kwon, Soonshin; Chen, Zack C Y; Noh, Hyunwoo; Lee, Ju Hun; Liu, Hang; Cha, Jennifer N; Xiang, Jie

    2014-07-21

    Crystalline silicon nanotubes (Si NTs) provide distinctive advantages as electrical and biochemical analysis scaffolds through their unique morphology and electrical tunability compared to solid nanowires or amorphous/non-conductive nanotubes. Such potential is investigated in this report. Gate-dependent four-probe current-voltage analysis reveals electrical properties such as resistivity to differ by nearly 3 orders of magnitude between crystalline and amorphous Si NTs. Analysis of transistor transfer characteristics yields a field effect mobility of 40.0 cm(2) V(-1) s(-1) in crystalline Si NTs. The hollow morphology also allows selective inner/outer surface functionalization and loading capability either as a carrier for molecular targets or as a nanofluidic channel for biomolecular assays. We present for the first time a demonstration of internalization of fluorescent dyes (rhodamine) and biomolecules (BSA) in Si NTs as long as 22 μm in length.

  13. ON current enhancement of nanowire Schottky barrier tunnel field effect transistors

    Science.gov (United States)

    Takei, Kohei; Hashimoto, Shuichiro; Sun, Jing; Zhang, Xu; Asada, Shuhei; Xu, Taiyu; Matsukawa, Takashi; Masahara, Meishoku; Watanabe, Takanobu

    2016-04-01

    Silicon nanowire Schottky barrier tunnel field effect transistors (NW-SBTFETs) are promising structures for high performance devices. In this study, we fabricated NW-SBTFETs to investigate the effect of nanowire structure on the device characteristics. The NW-SBTFETs were operated with a backgate bias, and the experimental results demonstrate that the ON current density is enhanced by narrowing the width of the nanowire. We confirmed using the Fowler-Nordheim plot that the drain current in the ON state mainly comprises the quantum tunneling component through the Schottky barrier. Comparison with a technology computer aided design (TCAD) simulation revealed that the enhancement is attributed to the electric field concentration at the corners of cross-section of the NW. The study findings suggest an effective approach to securing the ON current by Schottky barrier width modulation.

  14. ZnO piezoelectric fine wire gated graphene oxide field effect transistor.

    Science.gov (United States)

    Mohan, Rajneesh; Krishnamoorthy, Karthikeyan; Kim, Gui-Sik; Kim, Sang-Jae

    2013-05-01

    Here we report the fabrication and characteristics of graphene oxide (GO) field effect transistor gated with piezopotential of ZnO fine wires on a flexible substrate. The FET device consists of GO thin film on the bottom and ZnO piezoelectric fine wire (PFW) on the top. In the FET device the GO serves as a carrier transport channel and ZnO PFW acts as a gate. When the substrate is bent, a piezopotential is generated in the ZnO PFW. The piezopotential created by the strain in the ZnO PFW was used to control the carrier transport in the GO channel. This device demonstrates the application of piezoelectric ZnO PFW for creating the gating effect on the semiconducting performance of GO film.

  15. Method for extracting relevant electrical parameters from graphene field-effect transistors using a physical model

    Energy Technology Data Exchange (ETDEWEB)

    Boscá, A., E-mail: alberto.bosca@upm.es [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ingeniería Electrónica, E.T.S.I. de Telecomunicación, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Pedrós, J. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Campus de Excelencia Internacional, Campus Moncloa UCM-UPM, Madrid 28040 (Spain); Martínez, J. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ciencia de Materiales, E.T.S.I de Caminos, Canales y Puertos, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Calle, F. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ingeniería Electrónica, E.T.S.I. de Telecomunicación, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Campus de Excelencia Internacional, Campus Moncloa UCM-UPM, Madrid 28040 (Spain)

    2015-01-28

    Due to its intrinsic high mobility, graphene has proved to be a suitable material for high-speed electronics, where graphene field-effect transistor (GFET) has shown excellent properties. In this work, we present a method for extracting relevant electrical parameters from GFET devices using a simple electrical characterization and a model fitting. With experimental data from the device output characteristics, the method allows to calculate parameters such as the mobility, the contact resistance, and the fixed charge. Differentiated electron and hole mobilities and direct connection with intrinsic material properties are some of the key aspects of this method. Moreover, the method output values can be correlated with several issues during key fabrication steps such as the graphene growth and transfer, the lithographic steps, or the metalization processes, providing a flexible tool for quality control in GFET fabrication, as well as a valuable feedback for improving the material-growth process.

  16. 100-nm-size ferroelectric-gate field-effect transistor with 108-cycle endurance

    Science.gov (United States)

    Van Hai, Le; Takahashi, Mitsue; Zhang, Wei; Sakai, Shigeki

    2015-08-01

    The fabrication process of 100-nm-size ferroelectric-gate field-effect transistors (FeFETs) with high endurance was reported. The FeFETs had Pt/Sr0.8Ca0.2Bi2Ta2O9 (SCBT)/HfO2/Si stacks where the Pt gate length was 100 nm. The FeFETs were successfully fabricated by integrating many technologies such as fine patterning of etching masks by electron-beam lithography, precise anisotropic etching of the gate stacks, well-controlled ion implantation for gate-self-aligned sources and drains, and the sidewall-cover process that we had developed. Good performances of the FeFETs were characterized by the endurance of 108 program-and-erase cycles with negligible threshold-voltage shift and good drain-current retention for 3.98 × 105 s.

  17. Optimal design of an electret microphone metal-oxide-semiconductor field-effect transistor preamplifier.

    Science.gov (United States)

    van der Donk, A G; Bergveld, P

    1992-04-01

    A theoretical noise analysis of the combination of a capacitive microphone and a preamplifier containing a metal-oxide-semiconductor field-effect transistor (MOSFET) and a high-value resistive bias element is given. It is found that the output signal-to-noise ratio for a source follower and for a common-source circuit is almost the same. It is also shown that the output noise can be reduced by making the microphone capacitance as well as the bias resistor as large as possible, and furthermore by keeping the parasitic gate capacitances as low as possible and finally by using an optimum value for the gate area of the MOSFET. The main noise source is the thermal noise of the gate leakage resistance of the MOSFET. It is also shown that short-channel MOSFETs produce more thermal channel noise than longer channel devices.

  18. Multiple-trapping in pentacene field-effect transistors with a nanoparticles self-assembled monolayer

    Directory of Open Access Journals (Sweden)

    Keanchuan Lee

    2012-06-01

    Full Text Available A silver nanoparticles self-assembled monolayer (SAM was incorporated in pentacene field-effect transistor and its effects on the carrier injection and transport were investigated using the current-voltage (I − V and impedance spectroscopy (IS measurements. The I − V results showed that there was a significant negative shift of the threshold voltage, indicating the hole trapping inside the devices with about two orders higher in the contact resistance and an order lower in the effective mobility when a SAM was introduced. The IS measurements with the simulation using a Maxwell-Wagner equivalent circuit model revealed the existence of multiple trapping states for the devices with NPs, while the devices without NPs exhibited only a single trap state.

  19. Field-effect transistors with multiple channels constructed by carbon nanotubes

    Institute of Scientific and Technical Information of China (English)

    CHEN; Changxin; ZHANG; Yafei

    2005-01-01

    Single-wall carbon nanotubes (SWNTs) pre-decorated with functional molecules are directly aligned in the AC electric field, which makes SWNTs parallelly bridge the source and drain electrodes and act as the multiple conduction channels of the field-effect transistor (FET). The method avoids the mutual tanglement of SWNTs and makes them align between the source and drain electrodes abreast and dispersedly. It is indicated that aligning SWNTs in the high-volatility solvents can decrease the contaminant around the electrodes and has a function to purify the raw SWNTs. The obtained multi-channel FET not only takes on a high transconductance, but also holds the good reliability and stability.

  20. Switching Kinetics in Nanoscale Hafnium Oxide Based Ferroelectric Field-Effect Transistors.

    Science.gov (United States)

    Mulaosmanovic, Halid; Ocker, Johannes; Müller, Stefan; Schroeder, Uwe; Müller, Johannes; Polakowski, Patrick; Flachowsky, Stefan; van Bentum, Ralf; Mikolajick, Thomas; Slesazeck, Stefan

    2017-02-01

    The recent discovery of ferroelectricity in thin hafnium oxide films has led to a resurgence of interest in ferroelectric memory devices. Although both experimental and theoretical studies on this new ferroelectric system have been undertaken, much remains to be unveiled regarding its domain landscape and switching kinetics. Here we demonstrate that the switching of single domains can be directly observed in ultrascaled ferroelectric field effect transistors. Using models of ferroelectric domain nucleation we explain the time, field and temperature dependence of polarization reversal. A simple stochastic model is proposed as well, relating nucleation processes to the observed statistical switching behavior. Our results suggest novel opportunities for hafnium oxide based ferroelectrics in nonvolatile memory devices.

  1. Influence of thermocleavable functionality on organic field-effect transistor performance of small molecules

    Science.gov (United States)

    Mahale, Rajashree Y.; Dharmapurikar, Satej S.; Chini, Mrinmoy Kumar; Venugopalan, Vijay

    2017-06-01

    Diketopyrrolopyrrole based donor-acceptor-donor conjugated small molecules using ethylene dioxythiophene as a donor was synthesized. Electron deficient diketopyrrolopyrrole unit was substituted with thermocleavable (tert-butyl acetate) side chains. The thermal treatment of the molecules at 160 °C eliminated the tert-butyl ester group results in the formation of corresponding acid. Optical and theoretical studies revealed that the molecules adopted a change in molecular arrangement after thermolysis. The conjugated small molecules possessed p-channel charge transport characteristics in organic field effect transistors. The charge carrier mobility was increased after thermolysis of tert-butyl ester group to 5.07 × 10-5 cm2/V s.

  2. Investigation of drift effect on silicon nanowire field effect transistor based pH sensor

    Science.gov (United States)

    Kim, Sihyun; Kwon, Dae Woong; Lee, Ryoongbin; Kim, Dae Hwan; Park, Byung-Gook

    2016-06-01

    It is widely accepted that the operation mechanism of pH-sensitive ion sensitive field effect transistor (ISFET) can be divided into three categories; reaction of surface sites, chemical modification of insulator surface, and ionic diffusion into the bulk of insulator. The first mechanism is considered as the main operation mechanism of pH sensors due to fast response, while the others with relatively slow responses disturb accurate pH detection. In this study, the slow responses (often called drift effects) are investigated in silicon nanowire (SiNW) pH-sensitive ISFETs. Based on the dependence on the channel type of SiNW, liquid gate bias, and pH, it is clearly revealed that the drift of n-type SiNW results from H+ diffusion into the insulator whereas that of p-type SiNW is caused by chemical modification (hydration) of the insulator.

  3. Field-effect memory transistors based on arrays of nanowires of a ferroelectric polymer

    Science.gov (United States)

    Cai, Ronggang; Kassa, Hailu G.; Marrani, Alessio; van Breemen, Albert J. J. M.; Gelinck, Gerwin H.; Nysten, Bernard; Hu, Zhijun; Jonas, Alain M.

    2015-09-01

    Ferroelectric poly(vinylidene fluoride-co-trifluoroethylene), P(VDF-TrFE), is increasingly used in organic non-volatile memory devices, e.g., in ferroelectric field effect transistors (FeFETs). Here, we report on FeFETs integrating nanoimprinted arrays of P(VDF-TrFE) nanowires. Two previously-unreported architectures are tested, the first one consisting of stacked P(VDF-TrFE) nanowires placed over a continuous semiconducting polymer film; the second one consisting of a nanostriped blend layer wherein the semiconducting and ferroelectric components alternate regularly. The devices exhibit significant reversible memory effects, with operating voltages reduced compared to their continuous film equivalent, and with different possible geometries of the channels of free charge carriers accumulating in the semiconductor.

  4. Detection of influenza A virus using carbon nanotubes field effect transistor based DNA sensor

    Science.gov (United States)

    Tran, Thi Luyen; Nguyen, Thi Thuy; Huyen Tran, Thi Thu; Chu, Van Tuan; Thinh Tran, Quang; Tuan Mai, Anh

    2017-09-01

    The carbon nanotubes field effect transistor (CNTFET) based DNA sensor was developed, in this paper, for detection of influenza A virus DNA. Number of factors that influence the output signal and analytical results were investigated. The initial probe DNA, decides the available DNA strands on CNTs, was 10 μM. The hybridization time for defined single helix was 120 min. The hybridization temperature was set at 30 °C to get a net change in drain current of the DNA sensor without altering properties of any biological compounds. The response time of the DNA sensor was less than one minute with a high reproducibility. In addition, the DNA sensor has a wide linear detection range from 1 pM to 10 nM, and a very low detection limit of 1 pM. Finally, after 7-month storage in 7.4 pH buffer, the output signal of DNA sensor recovered 97%.

  5. Organic-inorganic proximity effect in the magneto-conductance of vertical organic field effect transistors

    Science.gov (United States)

    Khachatryan, B.; Greenman, M.; Devir-Wolfman, A. H.; Tessler, N.; Ehrenfreund, E.

    2016-07-01

    Vertical organic field effect transistors having a patterned source electrode and an a-SiO2 insulation layer show high performance as a switching element with high transfer characteristics. By measuring the low field magneto-conductance under ambient conditions at room temperature, we show here that the proximity of the inorganic a-SiO2 insulation to the organic conducting channel affects considerably the magnetic response. We propose that in n-type devices, electrons in the organic conducting channel and spin bearing charged defects in the inorganic a-SiO2 insulation layer (e.g., O2 = Si+.) form oppositely charged spin pairs whose singlet-triplet spin configurations are mixed through the relatively strong hyperfine field of 29Si. By increasing the contact area between the insulation layer and the conducting channel, the ˜2% magneto-conductance response may be considerably enhanced.

  6. A mathematical space mapping model for ballistic carbon nanotube field-effect transistors

    Science.gov (United States)

    Emamifar, Farnousha; Yousefi, Reza

    2016-11-01

    In this study, a mathematical model is presented based on mathematical space mapping for ballistic carbon nanotube field-effect transistors. This model is generalized from another model that was based on the concept of neural space mapping to calculate the three parameters of a coarse model. These parameters were the threshold voltage, the Early voltage, and assumed constant k of a modified "level 1" MOSFET model in simulation program with integrated circuit emphasis (SPICE). In this work, three analytical relations are introduced to replace the neural networks of the main model. The comparisons between the proposed model and a well-known reference model, named FETToy, show that the proposed model had reasonable accuracy in terms of different biases and physical parameters.

  7. High-performance integrated field-effect transistor-based sensors.

    Science.gov (United States)

    Adzhri, R; Md Arshad, M K; Gopinath, Subash C B; Ruslinda, A R; Fathil, M F M; Ayub, R M; Nor, M Nuzaihan Mohd; Voon, C H

    2016-04-21

    Field-effect transistors (FETs) have succeeded in modern electronics in an era of computers and hand-held applications. Currently, considerable attention has been paid to direct electrical measurements, which work by monitoring changes in intrinsic electrical properties. Further, FET-based sensing systems drastically reduce cost, are compatible with CMOS technology, and ease down-stream applications. Current technologies for sensing applications rely on time-consuming strategies and processes and can only be performed under recommended conditions. To overcome these obstacles, an overview is presented here in which we specifically focus on high-performance FET-based sensor integration with nano-sized materials, which requires understanding the interaction of surface materials with the surrounding environment. Therefore, we present strategies, material depositions, device structures and other characteristics involved in FET-based devices. Special attention was given to silicon and polyaniline nanowires and graphene, which have attracted much interest due to their remarkable properties in sensing applications.

  8. Organic nanofibers integrated by transfer technique in field-effect transistor devices

    DEFF Research Database (Denmark)

    Tavares, Luciana; Kjelstrup-Hansen, Jakob; Thilsing-Hansen, Kasper;

    2011-01-01

    The electrical properties of self-assembled organic crystalline nanofibers are studied by integrating these on field-effect transistor platforms using both top and bottom contact configurations. In the staggered geometries, where the nanofibers are sandwiched between the gate and the source-drain...... light on the charge injection and transport properties for such organic nanostructures and thus constitute a significant step forward towards a nanofiber-based light-emitting device.......-drain electrodes, a better electrical conduction is observed compared to the coplanar geometry where the nanofibers are placed over the gate and the source-drain electrodes. Qualitatively different output characteristics were observed for top and bottom contact devices reflecting the significantly different...... contact resistances. Bottom contact devices are dominated by contact effects while the top contact device characteristics are determined by the nanofiber bulk properties. It is found that the contact resistance is lower for crystalline nanofibers when compared to amorphous thin films. These results shed...

  9. Are Nanotube Architectures More Advantageous Than Nanowire Architectures For Field Effect Transistors?

    KAUST Repository

    Fahad, Hossain M.

    2012-06-27

    Decade long research in 1D nanowire field effect transistors (FET) shows although it has ultra-low off-state leakage current and a single device uses a very small area, its drive current generation per device is extremely low. Thus it requires arrays of nanowires to be integrated together to achieve appreciable amount of current necessary for high performance computation causing an area penalty and compromised functionality. Here we show that a FET with a nanotube architecture and core-shell gate stacks is capable of achieving the desirable leakage characteristics of the nanowire FET while generating a much larger drive current with area efficiency. The core-shell gate stacks of silicon nanotube FETs tighten the electrostatic control and enable volume inversion mode operation leading to improved short channel behavior and enhanced performance. Our comparative study is based on semi-classical transport models with quantum confinement effects which offers new opportunity for future generation high performance computation.

  10. Design Architecture of field-effect transistor with back gate electrode for biosensor application

    Science.gov (United States)

    Fathil, M. F. M.; Arshad, M. K. Md.; Hashim, U.; Ruslinda, A. R.; Gopinath, Subash C. B.; M. Nuzaihan M., N.; Ayub, R. M.; Adzhri, R.; Zaki, M.; Azman, A. H.

    2016-07-01

    This paper presents the preparation method of photolithography chrome mask design used in fabrication process of field-effect transistor with back gate biasing based biosensor. Initially, the chrome masks are designed by studying the process flow of the biosensor fabrication, followed by drawing of the actual chrome mask using the AutoCAD software. The overall width and length of the device is optimized at 16 mm and 16 mm, respectively. Fabrication processes of the biosensor required five chrome masks, which included source and drain formation mask, the back gate area formation mask, electrode formation mask, front gate area formation mask, and passivation area formation mask. The complete chrome masks design will be sent for chrome mask fabrication and for future use in biosensor fabrication.

  11. Zinc oxide nanorod field effect transistor for long-time cellular force measurement.

    Science.gov (United States)

    Zong, Xianli; Zhu, Rong

    2017-03-08

    Mechanical forces generated by cells are known to influence a vast range of cellular functions ranging from receptor signaling and transcription to differentiation and proliferation. We report a novel measurement approach using zinc oxide nanorods as a peeping transducer to monitor dynamic mechanical behavior of cellular traction on surrounding substrate. We develop a ZnO nanorod field effect transistor (FET) as an ultrasensitive force sensor to realize long-time, unstained, and in-situ detection of cell cycle phases, including attachment, spread, and mitosis. Excellent biocompatibility and ultra-sensitivity of the biomechanical measurement is ensured by coating a parylene film on the FET sensor as a concealment, which provides complete electronic isolation between the sensor and cell. With unique features of ultra-sensitivity, label-free, easy handling, and good biocompatibility, the force sensor allows feasible for tracking cellular dynamics in physiological contexts and understanding their contribution to biological processes.

  12. Simulation of GeSn/Ge tunneling field-effect transistors for complementary logic applications

    Science.gov (United States)

    Liu, Lei; Liang, Renrong; Wang, Jing; Xiao, Lei; Xu, Jun

    2016-09-01

    GeSn/Ge tunneling field-effect transistors (TFETs) with different device configurations are comprehensively investigated by numerical simulation. The lateral PIN- and PNPN-type point-tunneling and vertical line-tunneling device structures are analyzed and compared. Both n- and p-type TFETs are optimized to construct GeSn complementary logic applications. Simulation results indicate that GeSn/Ge heterochannel and heterosource structures significantly improve the device characteristics of point- and line-TFETs, respectively. Device performance and subthreshold swing can be further improved by increasing the Sn composition. GeSn/Ge heterosource line-TFETs exhibit excellent device performance and superior inverter voltage-transfer characteristic, which make them promising candidates for GeSn complementary TFET applications.

  13. The electrical characteristics of metal-oxide-semiconductor field effect transistors fabricated on cubic silicon carbide

    CERN Document Server

    Ohshima, T; Ishida, Y

    2003-01-01

    The n-channel metal-oxide-semiconductor field effect transistors (MOSFETs) were fabricated on cubic silicon carbide (3C-SiC) epitaxial layers grown on 3C-SiC substrates. The gate oxide of the MOSFETs was formed using pyrogenic oxidation at 1100 degC. The 3C-SiC MOSFETs showed enhancement type behaviors after annealing at 200degC for 30 min in argon atmosphere. The maximum value of the effective channel mobility of the 3C-SiC MOSFETs was 260cm sup 2 /V centre dot s. The leakage current of gate oxide was of a few tens of nA/cm sup 2 at an electric field range below 8.5 MV/cm, and breakdown began around 8.5MV/cm. (author)

  14. Intrinsic memory function of carbon nanotube-based ferroelectric field-effect transistor.

    Science.gov (United States)

    Fu, Wangyang; Xu, Zhi; Bai, Xuedong; Gu, Changzhi; Wang, Enge

    2009-03-01

    We demonstrate the intrinsic memory function of ferroelectric field-effect transistors (FeFETs) based on an integration of individual single-walled carbon nanotubes (SWCNTs) and epitaxial ferroelectric films. In contrast to the previously reported "charge-storage" CNT-FET memories, whose operations are haunted by a lack of control over the "charge traps", the present CNT-FeFETs exhibit a well-defined memory hysteresis loop induced by the reversible remnant polarization of the ferroelectric films. Large memory windows approximately 4 V, data retention time up to 1 week, and ultralow power consumption (energy per bit) of femto-joule, are highlighted in this report. Further simulations and experimental results show that the memory device is valid under operation voltage less than 1 V due to an electric-field enhancement effect induced by the ultrathin SWCNTs.

  15. Modeling and simulation of carbon nanotube field effect transistor and its circuit application

    Science.gov (United States)

    Singh, Amandeep; Saini, Dinesh Kumar; Agarwal, Dinesh; Aggarwal, Sajal; Khosla, Mamta; Raj, Balwinder

    2016-07-01

    The carbon nanotube field effect transistor (CNTFET) is modelled for circuit application. The model is based on the transport mechanism and it directly relates the transport mechanism with the chirality. Also, it does not consider self consistent equations and thus is used to develop the HSPICE compatible circuit model. For validation of the model, it is applied to the top gate CNTFET structure and the MATLAB simulation results are compared with the simulations of a similar structure created in NanoTCAD ViDES. For demonstrating the circuit compatibility of the model, two circuits viz. inverter and SRAM are designed and simulated in HSPICE. Finally, SRAM performance metrics are compared with those of device simulations from Nano TCAD ViDES.

  16. Analytic modeling of a depletion-mode cylindrical surrounding-gate nanowire field-effect transistor.

    Science.gov (United States)

    Yu, Yun Seop; Park, Hyung-Kun

    2012-07-01

    A compact model for depletion-mode p-type cylindrical surrounding-gate nanowire field-effect transistors (SGNWFETs) is proposed. The SGNWFET model consists of two back-to-back Schottky diodes for the metal-semiconductor (MS) contacts and the intrinsic SGNWFET. Based on the electrostatic method, the intrinsic SGNWFET model was derived from current conduction mechanisms attributed to bulk charges through the center neutral region, in addition to accumulation charges through the surface accumulation region. The authors' previously developed Schottky diode model was used for the M-S contacts. The new model was applied to an advanced design system (ADS), whereby the intrinsic part of the SGNWFET and the Schottky diode were developed using the Verilog-A language. The results of the simulation of the newly developed SGNWFET model reproduced the experiment results considerably well.

  17. A highly pH-sensitive nanowire field-effect transistor based on silicon on insulator

    Directory of Open Access Journals (Sweden)

    Denis E. Presnov

    2013-05-01

    Full Text Available Background: An experimental and theoretical study of a silicon-nanowire field-effect transistor made of silicon on insulator by CMOS-compatible methods is presented.Results: A maximum Nernstian sensitivity to pH change of 59 mV/pH was obtained experimentally. The maximum charge sensitivity of the sensor was estimated to be on the order of a thousandth of the electron charge in subthreshold mode.Conclusion: The sensitivity obtained for our sensor built in the CMOS-compatible top-down approach does not yield to the one of sensors built in bottom-up approaches. This provides a good background for the development of CMOS-compatible probes with primary signal processing on-chip.

  18. Realization of dual-channel organic field-effect transistors and their applications to chemical sensing

    Science.gov (United States)

    Jeong, Yeon Taek; Cobb, Brian H.; Lewis, Shannon D.; Dodabalapur, Ananth; Lu, Shaofeng; Facchetti, Antonio; Marks, Tobin J.

    2008-09-01

    We report on the realization of dual-channel organic field-effect transistors (FETs). These devices have a four-terminal configuration with a polymeric semiconductor p-channel, a small molecule semiconductor n-channel, and a polymeric gate dielectric. The polymeric p-channel and the small molecule n-channel are coupled across the gate dielectric. Both the p-FET and the n-FET exhibit acceptable device characteristics at ∣VDS∣⩽50V and ∣VG∣⩽50V, in which the performances of the p-FET and the n-FET are comparable. The p-FET and n-FET respond to isopropyl alcohol and ethanol vapors with significant sensitivities.

  19. Contact-dependent performance variability of monolayer MoS{sub 2} field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Han, Gyuchull; Yoon, Youngki, E-mail: youngki.yoon@uwaterloo.ca [Department of Electrical and Computer Engineering and Waterloo Institute for Nanotechnology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada)

    2014-11-24

    Using self-consistent quantum transport simulations, we investigate the performance variability of monolayer molybdenum disulfide (MoS{sub 2}) field-effect transistors (FETs) with various contact properties. Varying the Schottky barrier in MoS{sub 2} FETs affects the output characteristics more significantly than the transfer characteristics. If doped contacts are realized, the performance variation due to non-ideal contacts becomes negligible; otherwise, channel doping can effectively suppress the performance variability in metal-contact devices. Our scaling study also reveals that for sub-10-nm channels, doped-contact devices can be more robust in terms of switching, while metal-contact MoS{sub 2} FETs can undergo the smaller penalty in output conductance.

  20. Microscopic origin of low frequency noise in MoS2 field-effect transistors

    Directory of Open Access Journals (Sweden)

    Subhamoy Ghatak

    2014-09-01

    Full Text Available We report measurement of low frequency 1/f noise in molybdenum di-sulphide (MoS2 field-effect transistors in multiple device configurations including MoS2 on silicon dioxide as well as MoS2-hexagonal boron nitride (hBN heterostructures. All as-fabricated devices show similar magnitude of noise with number fluctuation as the dominant mechanism at high temperatures and density, although the calculated density of traps is two orders of magnitude higher than that at the SiO2 interface. Measurements on the heterostructure devices with vacuum annealing and dual gated configuration reveals that along with the channel, metal-MoS2 contacts also play a significant role in determining noise magnitude in these devices.

  1. Solvent Effects on the Transient Characteristics of Liquid-Gate Field Effect Transistors with Silicon Substrate

    Science.gov (United States)

    Yanase, Takashi; Hasegawa, Tetsuya; Nagahama, Taro; Shimada, Toshihiro

    2012-11-01

    The transient characteristics of electric double layer (EDL) gated field-effect transistors with Si as an active semiconductor were studied using various electrolyte solutions of LiBF4 by applying a step-function voltage to determine the optimum electrolyte for semiconductor circuits using EDLs. The tR, determined by EDL dynamics in the present experiment, was minimum as a function of the kind of solvent used owing to the competing effects of the EDL thickness and viscosity. The responses of the electrolyte solutions with various solvents at the same concentration were classified into three categories on the basis of tR: slow response of a complex-forming solvent, intermediate response of protic solvents, and fast response of nonprotic solvents. The best response time was 55 µs when a 1.0 M acetonitrile solution was used as the liquid-gate insulator.

  2. Hysteresis mechanism and control in pentacene organic field-effect transistors with polymer dielectric

    Directory of Open Access Journals (Sweden)

    Wei Huang

    2013-05-01

    Full Text Available Hysteresis mechanism of pentacene organic field-effect transistors (OFETs with polyvinyl alcohol (PVA and/or polymethyl methacrylate (PMMA dielectrics is studied. Through analyzing the electrical characteristics of OFETs with various PVA/PMMA arrangements, it shows that charge, which is trapped in PVA bulk and at the interface of pentacene/PVA, is one of the origins of hysteresis. The results also show that memory window is proportional to both trap amount in PVA and charge density at the gate/PVA or PVA/pentacene interfaces. Hence, the controllable memory window of around 0 ∼ 10 V can be realized by controlling the thickness and combination of triple-layer polymer dielectrics.

  3. Enhanced memory characteristics in organic ferroelectric field-effect transistors through thermal annealing

    Energy Technology Data Exchange (ETDEWEB)

    Sugano, Ryo; Tashiro, Tomoya; Sekine, Tomohito; Fukuda, Kenjiro; Kumaki, Daisuke; Tokito, Shizuo, E-mail: tokito@yz.yamagata-u.ac.jp [Graduate School of Science and Engineering, Yamagata University, 4-3-16 Jonan, Yonezawa, Yamagata 992-8510 (Japan); Research Center for Organic Electronics (ROEL), Yamagata University, 4-3-16 Jonan, Yonezawa, Yamagata 992-8510 (Japan)

    2015-11-15

    We report on the memory characteristics of organic ferroelectric field-effect transistors (FeFETs) using spin-coated poly(vinylidene difluoride/trifluoroethylene) (P(VDF/TrFE)) as a gate insulating layer. By thermal annealing the P(VDF/TrFE) layer at temperatures above its melting point, we could significantly improve the on/off current ratio to over 10{sup 4}. Considerable changes in the surface morphology and x-ray diffraction patterns were also observed in the P(VDF/TrFE) layer as a result of the annealing process. The enhanced memory effect is attributed to large polarization effects caused by rearranged ferroelectric polymer chains and improved crystallinity in the organic semiconductor layer of the FeFET devices.

  4. Field-effect transistor biosensors with two-dimensional black phosphorus nanosheets.

    Science.gov (United States)

    Chen, Yantao; Ren, Ren; Pu, Haihui; Chang, Jingbo; Mao, Shun; Chen, Junhong

    2017-03-15

    A black phosphorous (BP)-based field-effect transistor (FET) biosensor was fabricated by using few-layer BP nanosheets labeled with gold nanoparticle-antibody conjugates. BP nanosheets were mechanically exfoliated and used as the sensing/conducting channel in the FET, with an Al2O3 thin film as the dielectric layer for surface passivation. Antibody probes were conjugated with gold nanoparticles that were sputtered on the BP through surface functionalization. The sensor response was measured by the change in the BP's electrical resistance after antigens were introduced. The adsorbed antigens through specific antigen-antibody binding interactions induced a gate potential, thereby changing the drain-source current. The as-produced BP biosensor showed both high sensitivity (lower limit of detection ~10ng/ml) and selectivity towards human immunoglobulin G. Results from this study demonstrate the outstanding performance of BP as a sensing channel for FET biosensor applications.

  5. Biofunctionalized Zinc Oxide Field Effect Transistors for Selective Sensing of Riboflavin with Current Modulation

    Directory of Open Access Journals (Sweden)

    Morley O. Stone

    2011-06-01

    Full Text Available Zinc oxide field effect transistors (ZnO-FET, covalently functionalized with single stranded DNA aptamers, provide a highly selective platform for label-free small molecule sensing. The nanostructured surface morphology of ZnO provides high sensitivity and room temperature deposition allows for a wide array of substrate types. Herein we demonstrate the selective detection of riboflavin down to the pM level in aqueous solution using the negative electrical current response of the ZnO-FET by covalently attaching a riboflavin binding aptamer to the surface. The response of the biofunctionalized ZnO-FET was tuned by attaching a redox tag (ferrocene to the 3’ terminus of the aptamer, resulting in positive current modulation upon exposure to riboflavin down to pM levels.

  6. Influence of electron beam and ultraviolet irradiations on graphene field effect transistors

    Science.gov (United States)

    Iqbal, Muhammad Zahir; Siddique, Salma; Anwar, Nadia

    2017-10-01

    Electrical transport properties of graphene can be modulated by different controlled doping methods in order to make it useful for practical applications. Here we report a comparative study of electron-beam (e-beam) irradiated and ultraviolet (UV) irradiated graphene field effect transistors (FETs) for different doses and exposure times. We observed red shift in Raman spectra of graphene under e-beam irradiation which represents n-type doping while a divergent trend has been identified for UV irradiations which signify p-type doping. These results are further confirmed by the electrical transport measurements where the Dirac point shifts towards negative backgate voltage (i.e. n-type doping) upon e-beam exposure and shifted towards positive backgate voltage (i.e. p-type doping) under ultraviolet irradiation. Our approach reveals the dual characteristics of graphene FETs under these irradiation environments.

  7. Hole states in diamond p-delta-doped field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Orozco, J C; Rodriguez-Vargas, I [Unidad Academica de Fisica, Universidad Autonoma de Zacatecas, Calzada Solidaridad Esquina con Paseo la Bufa S/N, CP 98060 Zacatecas, ZAC. (Mexico); Mora-Ramos, M E, E-mail: jcmover@correo.unam.m [Facultad de Ciencias, Universidad Autonoma del Estado de Morelos, Av. Universidad 1001, Col. Chamilpa, CP 62209 Cuernavaca, MOR. (Mexico)

    2009-05-01

    The p-delta-doping in diamond allows to create high density two-dimensional hole gases. This technique has already been applied in the design and fabrication of diamond-based field effect transistors. Consequently, the knowledge of the electronic structure is of significant importance to understand the transport properties of diamond p-delta-doped systems. In this work the hole subbands of diamond p-type delta-doped quantum wells are studied within the framework of a local-density Thomas-Fermi-based approach for the band bending profile. The calculation incorporates an independent three-hole-band scheme and considers the effects of the contact potential, the delta-channel to contact distance, and the ionized impurity density.

  8. Two-Dimensional Transition Metal Dichalcogenides and Their Charge Carrier Mobilities in Field-Effect Transistors

    Science.gov (United States)

    Ahmed, Sohail; Yi, Jiabao

    2017-10-01

    Two-dimensional (2D) materials have attracted extensive interest due to their excellent electrical, thermal, mechanical, and optical properties. Graphene has been one of the most explored 2D materials. However, its zero band gap has limited its applications in electronic devices. Transition metal dichalcogenide (TMDC), another kind of 2D material, has a nonzero direct band gap (same charge carrier momentum in valence and conduction band) at monolayer state, promising for the efficient switching devices (e.g., field-effect transistors). This review mainly focuses on the recent advances in charge carrier mobility and the challenges to achieve high mobility in the electronic devices based on 2D-TMDC materials and also includes an introduction of 2D materials along with the synthesis techniques. Finally, this review describes the possible methodology and future prospective to enhance the charge carrier mobility for electronic devices.

  9. Effects of P3HT concentration on the performance of organic field effect transistors

    Institute of Scientific and Technical Information of China (English)

    JIANG Chun-xia; CHENG Xiao-man; WU Xiao-ming; YANG Xiao-yan; YIN Bin; HUA Yu-lin; WEI Jun; YIN Shou-gen

    2011-01-01

    @@ Top-contact organic field effect transistors (OFETs) based on poly(3-hexylthiophene) (P3HT) with different concentrations in chloroform (CHCl3) are fabricated.The output characteristics indicate that the P3HT concentration has significant influence on the OFET devices.The performance of the devices firstly is enhanced with increasing the P3HT concentration, and then decreases.The optimized devices with the P3HT concentration of 2 mg/mL show the best performance.The fieldeffect mobility is up to 1.4 × 10-2 cm2/Vs, the threshold voltage (Vt) is as low as -20 V, and the current on/off ratio (Ion/off) is close to the order of 104.The resu1ts suggest that the P3HT aggregation patterns induced by different concentrations can improve the performance of the OFETs.

  10. Calcium Ion Detection Using Miniaturized InN-based Ion Sensitive Field Effect Transistors

    Directory of Open Access Journals (Sweden)

    Kun-Wei Kao

    2012-03-01

    Full Text Available An Ultrathin (~10 nm InN ion sensitive field effect transistor (ISFET with gate regions functionalized with phosphotyrosine (p-Tyr is proposed to detect calcium ions (Ca2+ in aqueous solution. The ISFET was miniaturized to a chip size of 1.1 mm by 1.5 mm and integrated at the tip of a hypodermic injection needle (18 G for real-time and continuous monitoring. The sensor shows a current variation ratio of 1.11% with per decade change of Ca2+ and a detection limit of 10-6 M. The response time of 5 sec. reveals its great potential for accomplishing fast detection in chemical and physiological sensing applications. The sensor would be applied in medical diagnosis and used to monitor continuous and real-time variations of Ca2+ levels in human blood in the near future.

  11. Suppression of tunneling rate fluctuations in tunnel field-effect transistors by enhancing tunneling probability

    Science.gov (United States)

    Mori, Takahiro; Migita, Shinji; Fukuda, Koichi; Asai, Hidehiro; Morita, Yukinori; Mizubayashi, Wataru; Liu, Yongxun; O’uchi, Shin-ichi; Fuketa, Hiroshi; Otsuka, Shintaro; Yasuda, Tetsuji; Masahara, Meishoku; Ota, Hiroyuki; Matsukawa, Takashi

    2017-04-01

    This paper discusses the impact of the tunneling probability on the variability of tunnel field-effect transistors (TFETs). Isoelectronic trap (IET) technology, which enhances the tunneling current in TFETs, is used to suppress the variability of the ON current and threshold voltage. The simulation results show that suppressing the tunneling rate fluctuations results in suppression of the variability. In addition, a formula describing the relationship between the tunneling rate fluctuations and the electric field strength is derived based on Kane’s band-to-band tunneling model. This formula indicates that the magnitude of the tunneling rate fluctuations is proportional to the magnitude of the fluctuations in the electric field strength and a higher tunneling probability results in a lower variability. The derived relationship is universally valid for any technologies that exploit enhancement of the tunneling probability, including IET technology, channel material engineering, heterojunctions, strain engineering, etc.

  12. High-Temperature Stable Operation of Nanoribbon Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Kim Sangsig

    2010-01-01

    Full Text Available Abstract We experimentally demonstrated that nanoribbon field-effect transistors can be used for stable high-temperature applications. The on-current level of the nanoribbon FETs decreases at elevated temperatures due to the degradation of the electron mobility. We propose two methods of compensating for the variation of the current level with the temperature in the range of 25–150°C, involving the application of a suitable (1 positive or (2 negative substrate bias. These two methods were compared by two-dimensional numerical simulations. Although both approaches show constant on-state current saturation characteristics over the proposed temperature range, the latter shows an improvement in the off-state control of up to five orders of magnitude (−5.2 × 10−6.

  13. High yield fabrication of chemically reduced graphene oxide field effect transistors by dielectrophoresis

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Daeha; Chunder, A; Zhai, Lei; Khondaker, Saiful I, E-mail: saiful@mail.ucf.edu [Nanoscience Technology Center, University of Central Florida, Orlando, FL 32826 (United States)

    2010-04-23

    We demonstrate high yield fabrication of field effect transistors (FET) using chemically reduced graphene oxide (RGO) sheets. The RGO sheets suspended in water were assembled between prefabricated gold source and drain electrodes using ac dielectrophoresis. With the application of a backgate voltage, 60% of the devices showed p-type FET behavior, while the remaining 40% showed ambipolar behavior. After mild thermal annealing at 200 deg. C, all ambipolar RGO FET remained ambipolar with increased hole and electron mobility, while 60% of the p-type RGO devices were transformed to ambipolar. The maximum hole and electron mobilities of the devices were 4.0 and 1.5 cm{sup 2} V{sup -1} s{sup -1} respectively. High yield assembly of chemically derived RGO FET will have significant impact in scaled up fabrication of graphene based nanoelectronic devices.

  14. Electrical properties of NiO/PVC nano hybrid composites for organic field effect transistors

    Science.gov (United States)

    Hayati, A.; Bahari, A.

    2015-01-01

    In this study, NiO/PVC nano hybrid composites have been synthesized through sol-gel method. Nano crystallites phases, crystallinity and electrical properties have been characterized using X-ray diffraction, Fourier transfer infrared radiation, scanning electron microscopy and atomic force microscopy techniques. The dielectric constant of the samples has been calculated through measuring the capacity of samples by application of GPS 132 A. Obtained results have indicated that an NiO/PVC sample with 5 g NiO and 0.02 g PVC, equivalent to 0.4 %wt PVC, in weight synthesis, at a temperature of 80 °C has a higher dielectric constant, better surface morphology, less rough surface, less leakage current, and thus has potential to be suggested as a possible gate dielectric material for future organic field effect transistor devices.

  15. Improved Drain Current Saturation and Voltage Gain in Graphene-on-Silicon Field Effect Transistors

    Science.gov (United States)

    Song, Seung Min; Bong, Jae Hoon; Hwang, Wan Sik; Cho, Byung Jin

    2016-05-01

    Graphene devices for radio frequency (RF) applications are of great interest due to their excellent carrier mobility and saturation velocity. However, the insufficient current saturation in graphene field effect transistors (FETs) is a barrier preventing enhancements of the maximum oscillation frequency and voltage gain, both of which should be improved for RF transistors. Achieving a high output resistance is therefore a crucial step for graphene to be utilized in RF applications. In the present study, we report high output resistances and voltage gains in graphene-on-silicon (GoS) FETs. This is achieved by utilizing bare silicon as a supporting substrate without an insulating layer under the graphene. The GoSFETs exhibit a maximum output resistance of 2.5 MΩ•μm, maximum intrinsic voltage gain of 28 dB, and maximum voltage gain of 9 dB. This method opens a new route to overcome the limitations of conventional graphene-on-insulator (GoI) FETs and subsequently brings graphene electronics closer to practical usage.

  16. Room-temperature amorphous alloy field-effect transistor exhibiting particle and wave electronic transport

    Energy Technology Data Exchange (ETDEWEB)

    Fukuhara, M., E-mail: fukuhara@niche.tohoku.ac.jp [New Industry Creation Hatchery Center, Tohoku University, Sendai 980-8579 (Japan); Kawarada, H. [Research and Development Center, Waseda University, Tokyo 162-0041 (Japan)

    2015-02-28

    The realization of room-temperature macroscopic field effect transistors (FETs) will lead to new epoch-making possibilities for electronic applications. The I{sub d}-V{sub g} characteristics of the millimeter-sized aluminum-oxide amorphous alloy (Ni{sub 0.36}Nb{sub 0.24}Zr{sub 0.40}){sub 90}H{sub 10} FETs were measured at a gate-drain bias voltage of 0–60 μV in nonmagnetic conditions and under a magnetic fields at room temperature. Application of dc voltages to the gate electrode resulted in the transistor exhibiting one-electron Coulomb oscillation with a period of 0.28 mV, Fabry-Perot interference with a period of 2.35 μV under nonmagnetic conditions, and a Fano effect with a period of 0.26 mV for Vg and 0.2 T under a magnetic field. The realization of a low-energy controllable device made from millimeter-sized Ni-Nb-Zr-H amorphous alloy throws new light on cluster electronics.

  17. High-mobility solution-processed copper phthalocyanine-based organic field-effect transistors

    Directory of Open Access Journals (Sweden)

    Nandu B Chaure, Andrew N Cammidge, Isabelle Chambrier, Michael J Cook, Markys G Cain, Craig E Murphy, Chandana Pal and Asim K Ray

    2011-01-01

    Full Text Available Solution-processed films of 1,4,8,11,15,18,22,25-octakis(hexyl copper phthalocyanine (CuPc6 were utilized as an active semiconducting layer in the fabrication of organic field-effect transistors (OFETs in the bottom-gate configurations using chemical vapour deposited silicon dioxide (SiO2 as gate dielectrics. The surface treatment of the gate dielectric with a self-assembled monolayer of octadecyltrichlorosilane (OTS resulted in values of 4×10−2 cm2 V−1 s−1 and 106 for saturation mobility and on/off current ratio, respectively. This improvement was accompanied by a shift in the threshold voltage from 3 V for untreated devices to -2 V for OTS treated devices. The trap density at the interface between the gate dielectric and semiconductor decreased by about one order of magnitude after the surface treatment. The transistors with the OTS treated gate dielectrics were more stable over a 30-day period in air than untreated ones.

  18. Boron δ-doped (111) diamond solution gate field effect transistors.

    Science.gov (United States)

    Edgington, Robert; Ruslinda, A Rahim; Sato, Syunsuke; Ishiyama, Yuichiro; Tsuge, Kyosuke; Ono, Tasuku; Kawarada, Hiroshi; Jackman, Richard B

    2012-03-15

    A solution gate field effect transistor (SGFET) using an oxidised boron δ-doped channel on (111) diamond is presented for the first time. Employing an optimised plasma chemical vapour deposition (PECVD) recipe to deposit δ-layers, SGFETs show improved current-voltage (I-V) characteristics in comparison to previous similar devices fabricated on (100) and polycrystalline diamond, where the device is shown to operate in the enhancement mode of operation, achieving channel pinch-off and drain-source current saturation within the electrochemical window of diamond. A maximum gain and transconductance of 3 and 200μS/mm are extracted, showing comparable figures of merit to hydrogen-based SGFET. The oxidised device shows a site-binding model pH sensitivity of 36 mV/pH, displaying fast temporal responses. Considering the biocompatibility of diamond towards cells, the device's highly mutable transistor characteristics, pH sensitivity and stability against anodic oxidation common to hydrogen terminated diamond SGFET, oxidised boron δ-doped diamond SGFETs show promise for the recording of action potentials from electrogenic cells. Copyright © 2011 Elsevier B.V. All rights reserved.

  19. Unique Characteristics of Vertical Carbon Nanotube Field-effect Transistors on Silicon

    KAUST Repository

    Li, Jingqi

    2014-07-01

    A vertical carbon nanotube field-effect transistor (CNTFET) based on silicon (Si) substrate has been proposed and simulated using a semi-classical theory. A single-walled carbon nanotube (SWNT) and an n-type Si nanowire in series construct the channel of the transistor. The CNTFET presents ambipolar characteristics at positive drain voltage (Vd) and n-type characteristics at negative Vd. The current is significantly influenced by the doping level of n-Si and the SWNT band gap. The n-branch current of the ambipolar characteristics increases with increasing doping level of the n-Si while the p-branch current decreases. The SWNT band gap has the same influence on the p-branch current at a positive Vd and n-type characteristics at negative Vd. The lower the SWNT band gap, the higher the current. However, it has no impact on the n-branch current in the ambipolar characteristics. Thick oxide is found to significantly degrade the current and the subthreshold slope of the CNTFETs.

  20. Single Nucleotide Polymorphism Detection Using Au-Decorated Single-Walled Carbon Nanotube Field Effect Transistors

    Directory of Open Access Journals (Sweden)

    Keum-Ju Lee

    2011-01-01

    Full Text Available We demonstrate that Au-cluster-decorated single-walled carbon nanotubes (SWNTs may be used to discriminate single nucleotide polymorphism (SNP. Nanoscale Au clusters were formed on the side walls of carbon nanotubes in a transistor geometry using electrochemical deposition. The effect of Au cluster decoration appeared as hole doping when electrical transport characteristics were examined. Thiolated single-stranded probe peptide nucleic acid (PNA was successfully immobilized on Au clusters decorating single-walled carbon nanotube field-effect transistors (SWNT-FETs, resulting in a conductance decrease that could be explained by a decrease in Au work function upon adsorption of thiolated PNA. Although a target single-stranded DNA (ssDNA with a single mismatch did not cause any change in electrical conductance, a clear decrease in conductance was observed with matched ssDNA, thereby showing the possibility of SNP (single nucleotide polymorphism detection using Au-cluster-decorated SWNT-FETs. However, a power to discriminate SNP target is lost in high ionic environment. We can conclude that observed SNP discrimination in low ionic environment is due to the hampered binding of SNP target on nanoscale surfaces in low ionic conditions.

  1. Investigation of the dimensionality of charge transport in organic field effect transistors

    Science.gov (United States)

    Abdalla, Hassan; Fabiano, Simone; Kemerink, Martijn

    2017-02-01

    Ever since the first experimental investigations of organic field effect transistors (OFETs) the dimensionality of charge transport has alternately been described as two dimensional (2D) and three dimensional (3D). More recently, researchers have turned to an analytical analysis of the temperature-dependent transfer characteristics to classify the dimensionality as either 2D or 3D as well as to determine the disorder of the system, thereby greatly simplifying dimensionality investigations. We applied said analytical analysis to the experimental results of our OFETs comprising molecularly well-defined polymeric layers as the active material as well as to results obtained from kinetic Monte Carlo simulations and found that it was not able to correctly distinguish between 2D and 3D transports or give meaningful values for the disorder and should only be used for quasiquantitative and comparative analysis. We conclude to show that the dimensionality of charge transport in OFETs is a function of the interplay between transistor physics and morphology of the organic material.

  2. Influence of contact height on the performance of vertically aligned carbon nanotube field-effect transistors

    KAUST Repository

    Li, Jingqi

    2013-01-01

    Vertically aligned carbon nanotube field-effect transistors (CNTFETs) have been experimentally demonstrated (J. Li et al., Carbon, 2012, 50, 4628-4632). The source and drain contact heights in vertical CNTFETs could be much higher than in flat CNTFETs if the fabrication process is not optimized. To understand the impact of contact height on transistor performance, we use a semi-classical method to calculate the characteristics of CNTFETs with different contact heights. The results show that the drain current decreases with increasing contact height and saturates at a value governed by the thickness of the oxide. The current reduction caused by the increased contact height becomes more significant when the gate oxide is thicker. The higher the drain voltage, the larger the current reduction. It becomes even worse when the band gap of the carbon nanotube is larger. The current can differ by a factor of more than five between the CNTEFTs with low and high contact heights when the oxide thickness is 50 nm. In addition, the influence of the contact height is limited by the channel length. The contact height plays a minor role when the channel length is less than 100 nm. © 2013 The Royal Society of Chemistry.

  3. Touch sensors based on planar liquid crystal-gated-organic field-effect transistors

    Science.gov (United States)

    Seo, Jooyeok; Lee, Chulyeon; Han, Hyemi; Lee, Sooyong; Nam, Sungho; Kim, Hwajeong; Lee, Joon-Hyung; Park, Soo-Young; Kang, Inn-Kyu; Kim, Youngkyoo

    2014-09-01

    We report a tactile touch sensor based on a planar liquid crystal-gated-organic field-effect transistor (LC-g-OFET) structure. The LC-g-OFET touch sensors were fabricated by forming the 10 μm thick LC layer (4-cyano-4'-pentylbiphenyl - 5CB) on top of the 50 nm thick channel layer (poly(3-hexylthiophene) - P3HT) that is coated on the in-plane aligned drain/source/gate electrodes (indium-tin oxide - ITO). As an external physical stimulation to examine the tactile touch performance, a weak nitrogen flow (83.3 μl/s) was employed to stimulate the LC layer of the touch device. The LC-g-OFET device exhibited p-type transistor characteristics with a hole mobility of 1.5 cm2/Vs, but no sensing current by the nitrogen flow touch was measured at sufficiently high drain (VD) and gate (VG) voltages. However, a clear sensing current signal was detected at lower voltages, which was quite sensitive to the combination of VD and VG. The best voltage combination was VD = -0.2 V and VG = -1 V for the highest ratio of signal currents to base currents (i.e., signal-to-noise ratio). The change in the LC alignment upon the nitrogen flow touch was assigned as the mechanism for the present LC-g-OFET touch sensors.

  4. Ambipolar Small-Molecule:Polymer Blend Semiconductors for Solution-Processable Organic Field-Effect Transistors.

    Science.gov (United States)

    Kang, Minji; Hwang, Hansu; Park, Won-Tae; Khim, Dongyoon; Yeo, Jun-Seok; Kim, Yunseul; Kim, Yeon-Ju; Noh, Yong-Young; Kim, Dong-Yu

    2017-01-25

    We report on the fabrication of an organic thin-film semiconductor formed using a blend solution of soluble ambipolar small molecules and an insulating polymer binder that exhibits vertical phase separation and uniform film formation. The semiconductor thin films are produced in a single step from a mixture containing a small molecular semiconductor, namely, quinoidal biselenophene (QBS), and a binder polymer, namely, poly(2-vinylnaphthalene) (PVN). Organic field-effect transistors (OFETs) based on QBS/PVN blend semiconductor are then assembled using top-gate/bottom-contact device configuration, which achieve almost four times higher mobility than the neat QBS semiconductor. Depth profile via secondary ion mass spectrometry and atomic force microscopy images indicate that the QBS domains in the films made from the blend are evenly distributed with a smooth morphology at the bottom of the PVN layer. Bias stress test and variable-temperature measurements on QBS-based OFETs reveal that the QBS/PVN blend semiconductor remarkably reduces the number of trap sites at the gate dielectric/semiconductor interface and the activation energy in the transistor channel. This work provides a one-step solution processing technique, which makes use of soluble ambipolar small molecules to form a thin-film semiconductor for application in high-performance OFETs.

  5. Electrostatic melting in a single-molecule field-effect transistor with applications in genomic identification

    Science.gov (United States)

    Vernick, Sefi; Trocchia, Scott M.; Warren, Steven B.; Young, Erik F.; Bouilly, Delphine; Gonzalez, Ruben L.; Nuckolls, Colin; Shepard, Kenneth L.

    2017-05-01

    The study of biomolecular interactions at the single-molecule level holds great potential for both basic science and biotechnology applications. Single-molecule studies often rely on fluorescence-based reporting, with signal levels limited by photon emission from single optical reporters. The point-functionalized carbon nanotube transistor, known as the single-molecule field-effect transistor, is a bioelectronics alternative based on intrinsic molecular charge that offers significantly higher signal levels for detection. Such devices are effective for characterizing DNA hybridization kinetics and thermodynamics and enabling emerging applications in genomic identification. In this work, we show that hybridization kinetics can be directly controlled by electrostatic bias applied between the device and the surrounding electrolyte. We perform the first single-molecule experiments demonstrating the use of electrostatics to control molecular binding. Using bias as a proxy for temperature, we demonstrate the feasibility of detecting various concentrations of 20-nt target sequences from the Ebolavirus nucleoprotein gene in a constant-temperature environment.

  6. Uncovering edge states and electrical inhomogeneity in MoS2 field-effect transistors.

    Science.gov (United States)

    Wu, Di; Li, Xiao; Luan, Lan; Wu, Xiaoyu; Li, Wei; Yogeesh, Maruthi N; Ghosh, Rudresh; Chu, Zhaodong; Akinwande, Deji; Niu, Qian; Lai, Keji

    2016-08-02

    The understanding of various types of disorders in atomically thin transition metal dichalcogenides (TMDs), including dangling bonds at the edges, chalcogen deficiencies in the bulk, and charges in the substrate, is of fundamental importance for TMD applications in electronics and photonics. Because of the imperfections, electrons moving on these 2D crystals experience a spatially nonuniform Coulomb environment, whose effect on the charge transport has not been microscopically studied. Here, we report the mesoscopic conductance mapping in monolayer and few-layer MoS2 field-effect transistors by microwave impedance microscopy (MIM). The spatial evolution of the insulator-to-metal transition is clearly resolved. Interestingly, as the transistors are gradually turned on, electrical conduction emerges initially at the edges before appearing in the bulk of MoS2 flakes, which can be explained by our first-principles calculations. The results unambiguously confirm that the contribution of edge states to the channel conductance is significant under the threshold voltage but negligible once the bulk of the TMD device becomes conductive. Strong conductance inhomogeneity, which is associated with the fluctuations of disorder potential in the 2D sheets, is also observed in the MIM images, providing a guideline for future improvement of the device performance.

  7. Proton migration mechanism for operational instabilities in organic field-effect transistors

    Science.gov (United States)

    Sharma, A.; Mathijssen, S. G. J.; Smits, E. C. P.; Kemerink, M.; de Leeuw, D. M.; Bobbert, P. A.

    2010-08-01

    Organic field-effect transistors exhibit operational instabilities involving a shift of the threshold gate voltage when a gate bias is applied. For a constant gate bias the threshold voltage shifts toward the applied gate bias voltage, an effect known as the bias-stress effect. Here, we report on a detailed experimental and theoretical study of operational instabilities in p -type transistors with silicon-dioxide gate dielectric both for a constant as well as for a dynamic gate bias. We associate the instabilities with a reversible reaction in the organic semiconductor in which holes are converted into protons in the presence of water and a reversible migration of these protons into the gate dielectric. We show how redistribution of charge between holes in the semiconductor and protons in the gate dielectric can consistently explain the experimental observations. Furthermore, we show how a shorter period of application of a gate bias leads to a faster backward shift of the threshold voltage when the gate bias is removed. The proposed mechanism is consistent with the observed acceleration of the bias-stress effect with increasing humidity, increasing temperature, and increasing energy of the highest molecular orbital of the organic semiconductor.

  8. High performance field-effect transistor based on multilayer tungsten disulfide.

    Science.gov (United States)

    Liu, Xue; Hu, Jin; Yue, Chunlei; Della Fera, Nicholas; Ling, Yun; Mao, Zhiqiang; Wei, Jiang

    2014-10-28

    Semiconducting two-dimensional transition metal chalcogenide crystals have been regarded as the promising candidate for the future generation of transistor in modern electronics. However, how to fabricate those crystals into practical devices with acceptable performance still remains as a challenge. Employing tungsten disulfide multilayer thin crystals, we demonstrate that using gold as the only contact metal and choosing appropriate thickness of the crystal, high performance transistor with on/off ratio of 10(8) and mobility up to 234 cm(2) V(-1) s(-1) at room temperature can be realized in a simple device structure. Furthermore, low temperature study revealed that the high performance of our device is caused by the minimized Schottky barrier at the contact and the existence of a shallow impurity level around 80 meV right below the conduction band edge. From the analysis on temperature dependence of field-effect mobility, we conclude that strongly suppressed phonon scattering and relatively low charge impurity density are the key factors leading to the high mobility of our tungsten disulfide devices.

  9. pn-Heterojunction effects of perylene tetracarboxylic diimide derivatives on pentacene field-effect transistor.

    Science.gov (United States)

    Yu, Seong Hun; Kang, Boseok; An, Gukil; Kim, BongSoo; Lee, Moo Hyung; Kang, Moon Sung; Kim, Hyunjung; Lee, Jung Heon; Lee, Shichoon; Cho, Kilwon; Lee, Jun Young; Cho, Jeong Ho

    2015-01-28

    We investigated the heterojunction effects of perylene tetracarboxylic diimide (PTCDI) derivatives on the pentacene-based field-effect transistors (FETs). Three PTCDI derivatives with different substituents were deposited onto pentacene layers and served as charge transfer dopants. The deposited PTCDI layer, which had a nominal thickness of a few layers, formed discontinuous patches on the pentacene layers and dramatically enhanced the hole mobility in the pentacene FET. Among the three PTCDI molecules tested, the octyl-substituted PTCDI, PTCDI-C8, provided the most efficient hole-doping characteristics (p-type) relative to the fluorophenyl-substituted PTCDIs, 4-FPEPTC and 2,4-FPEPTC. The organic heterojunction and doping characteristics were systematically investigated using atomic force microscopy, 2D grazing incidence X-ray diffraction studies, and ultraviolet photoelectron spectroscopy. PTCDI-C8, bearing octyl substituents, grew laterally on the pentacene layer (2D growth), whereas 2,4-FPEPTC, with fluorophenyl substituents, underwent 3D growth. The different growth modes resulted in different contact areas and relative orientations between the pentacene and PTCDI molecules, which significantly affected the doping efficiency of the deposited adlayer. The differences between the growth modes and the thin-film microstructures in the different PTCDI patches were attributed to a mismatch between the surface energies of the patches and the underlying pentacene layer. The film-morphology-dependent doping effects observed here offer practical guidelines for achieving more effective charge transfer doping in thin-film transistors.

  10. Using gapped topological surface states of Bi2Se3 films in a field effect transistor

    Science.gov (United States)

    Sun, Jifeng; Singh, David J.

    2017-02-01

    Three dimensional topological insulators are insulators with topologically protected surface states that can have a high band velocity and high mobility at room temperature. This suggests electronic applications that exploit these surface states, but the lack of a band gap poses a fundamental difficulty. We report a first principles study based on density functional theory for thin Bi2Se3 films in the context of a field effect transistor. It is known that a gap is induced in thin layers due to hybridization between the top and bottom surfaces, but it is not known whether it is possible to use the topological states in this type of configuration. In particular, it is unclear whether the benefits of topological protection can be retained to a sufficient degree. We show that there is a thickness regime in which the small gap induced by hybridization between the two surfaces is sufficient to obtain transistor operation at room temperature, and furthermore, that the band velocity and spin texture that are important for the mobility are preserved for Fermi levels of relevance to device application.

  11. Thermal analytic model of current gain for bipolar junction transistor-bipolar static induction transistor compound device

    Institute of Scientific and Technical Information of China (English)

    Zhang You-Run; Zhang Bo; Li Ze-Hong; Lai Chang-Jin; Li Zhao-Ji

    2009-01-01

    This paper proposes a thermal analytical model of current gain for bipolar junction transistor-bipolar static induction transistor (BJT-BSIT) compound device in the low current operation. It also proposes a best thermal compensating factor to the compound device that indicates the relationship between the thermal variation rate of current gain and device structure. This is important for the design of compound device to be optimized. Finally, the analytical model is found to be in good agreement with numerical simulation and experimental results. The test results demonstrate that thermal variation rate of current gain is below 10% in 25℃C-85℃ and 20% in -55℃-25℃.

  12. MOBILITAS PEMBAWA MUATAN PADA OFET (ORGANIC FIELD EFFECT TRANSISTOR BERBASIS FILM TIPIS

    Directory of Open Access Journals (Sweden)

    Sujarwata -

    2014-06-01

    Full Text Available Abstrak __________________________________________________________________________________________ Tujuan penelitian ini adalah pembuatan dan karakterisasi pada OFET (Organic Field Effect Transistor berbasis film tipis dengan struktur bottom-contact. Pembuatan OFET dilakukan dengan cara pencucian substrat dengan etanol dalam ultrasonic cleaner, kemudian dilakukan deposisi elektroda source dan drain di atas substrat SiO2 dengan metode  penguapan hampa udara pada suhu ruang dan teknik lithography. Selanjutnya dilakukan deposisi film tipis CuPc diantara source (S dan drain (D sebagai panjang saluran (channel dan diakhiri dengan deposisi elektrode gate (G. Karakterisai OFET berbasis film tipis dilakukan dengan El-Kahfi 100, untuk menentukan karakteristik keluaran V-I. Hasil karakterisasi OFET dengan panjang channel (L 100 μm dan lebar (W 1 mm, mempunyai daerah aktif, yaitu: 2,80 V sampai dengan 3,42. Mobilitas pembawa muatan OFET untuk daerah saturasi, µ = 0,00182278 cm2 /Vs dan untuk daerah linier, µ = 0,000343818  cm2 /Vs   Abstract __________________________________________________________________________________________ The purpose of this research is to produce and characterize the OFET (Organic Field Effect Transistor based on thin film with bottom-contact structure. The OFET production consists of the substract wash by using ethanol in the ultrasonic cleaner, then electrode deposition of source and drain on the SiO2 substract by using vacuum evaporation in the room temperature and lithography technique.  Then, the deposition of thin film of CuPc between source (S and drain (D was done as the channel length and ended with electrode gate (G deposition. The OFET characterization  with channel length (L  100 μm and wide (W 1 mm  obtained the active area of 2,80 - 3,42 v. While the mobility of OFET charge carrier  obtained µ =  0,00182278 cm2 /Vs for the saturation area and µ = 0,000343818  cm2 /Vs for linier area.

  13. MOBILITAS PEMBAWA MUATAN PADA OFET (ORGANIC FIELD EFFECT TRANSISTOR BERBASIS FILM TIPIS

    Directory of Open Access Journals (Sweden)

    Sujarwata -

    2014-06-01

    Full Text Available Abstrak __________________________________________________________________________________________ Tujuan penelitian ini adalah pembuatan dan karakterisasi pada OFET (Organic Field Effect Transistor berbasis film tipis dengan struktur bottom-contact. Pembuatan OFET dilakukan dengan cara pencucian substrat dengan etanol dalam ultrasonic cleaner, kemudian dilakukan deposisi elektroda source dan drain di atas substrat SiO2 dengan metode  penguapan hampa udara pada suhu ruang dan teknik lithography. Selanjutnya dilakukan deposisi film tipis CuPc diantara source (S dan drain (D sebagai panjang saluran (channel dan diakhiri dengan deposisi elektrode gate (G. Karakterisai OFET berbasis film tipis dilakukan dengan El-Kahfi 100, untuk menentukan karakteristik keluaran V-I. Hasil karakterisasi OFET dengan panjang channel (L 100 μm dan lebar (W 1 mm, mempunyai daerah aktif, yaitu: 2,80 V sampai dengan 3,42. Mobilitas pembawa muatan OFET untuk daerah saturasi, µ = 0,00182278 cm2 /Vs dan untuk daerah linier, µ = 0,000343818  cm2 /Vs   Abstract __________________________________________________________________________________________ The purpose of this research is to produce and characterize the OFET (Organic Field Effect Transistor based on thin film with bottom-contact structure. The OFET production consists of the substract wash by using ethanol in the ultrasonic cleaner, then electrode deposition of source and drain on the SiO2 substract by using vacuum evaporation in the room temperature and lithography technique.  Then, the deposition of thin film of CuPc between source (S and drain (D was done as the channel length and ended with electrode gate (G deposition. The OFET characterization  with channel length (L  100 μm and wide (W 1 mm  obtained the active area of 2,80 - 3,42 v. While the mobility of OFET charge carrier  obtained µ =  0,00182278 cm2 /Vs for the saturation area and µ = 0,000343818  cm2 /Vs for linier area.

  14. Red light sensitive heterojunction organic field-effect transistors based on neodymium phthalocyanine as photosensitive layer

    Energy Technology Data Exchange (ETDEWEB)

    Lv, Wenli; Tang, Yu [Institute of Microelectronics, School of Physical Science and Technology, Lanzhou University, South Tianshui Road 222#, Lanzhou 730000 (China); Yao, Bo [Institute of Microelectronics, School of Physical Science and Technology, Lanzhou University, South Tianshui Road 222#, Lanzhou 730000 (China); Department of Physics, Shaoxing University, Shaoxing 312000 (China); Zhou, Maoqing; Luo, Xiao; Li, Yao; Zhong, Junkang; Sun, Lei [Institute of Microelectronics, School of Physical Science and Technology, Lanzhou University, South Tianshui Road 222#, Lanzhou 730000 (China); Peng, Yingquan, E-mail: yqpeng@lzu.edu.cn [Institute of Microelectronics, School of Physical Science and Technology, Lanzhou University, South Tianshui Road 222#, Lanzhou 730000 (China); Key Laboratory for Magnetism and Magnetic Materials of the Ministry of Education, Lanzhou University, South Tianshui Road 222#, Lanzhou 730000 (China)

    2015-08-31

    Compared with organic photodiodes, photoresponsive organic field-effect transistors (photOFETs) exhibit higher sensitivity and lower noise. The performance of photOFETs based on conventional single layer structure is generally poor due to the low carrier mobility of the active channel materials. We demonstrate a high performance photOFET operating in red light with a structure of C60/neodymium phthalocyanine (NdPc{sub 2}) planar heterojunction. PhotOFETs based on single-layer NdPc{sub 2} and C60/NdPc{sub 2} heterojunction (denoted as NdPc{sub 2}-photOFETs and C60/NdPc{sub 2}-photOFETs, respectively) were fabricated and characterized. It is concluded that the photOFETs with heterojunction structure showed superior performance compared to that of single layer photOFETs. And for red light with a wavelength of 655 nm, C60/NdPc{sub 2}-photOFETs exhibited a large photoresponsivity of ~ 0.8 A/W, which is approximately 62 times larger than that of NdPc{sub 2}-photOFETs under the same conditions. The high performance of C60/NdPc{sub 2}-photOFETs is attributed to its high light absorption coefficient, high exciton dissociation efficiency and high carrier mobility. - Highlights: • The mobility of light-sensitive organic materials is generally low. • We fabricated C60/NdPc{sub 2} photoresponsive organic field-effect transistors (photOFETs). • The performance of C60/NdPc{sub 2} photOFETs is superior than single-layer NdPc{sub 2} photOFETs. • C60/NdPc{sub 2} photOFETs exhibited a large photoresponsivity of ~ 0.8 A/W for red light.

  15. Graphene-based field effect transistor in two-dimensional paper networks

    Energy Technology Data Exchange (ETDEWEB)

    Cagang, Aldrine Abenoja; Abidi, Irfan Haider; Tyagi, Abhishek [Department of Chemical and Biomolecular Engineering, Hong Kong University of Science and Technology, Clear Water Bay (Hong Kong); Hu, Jie; Xu, Feng [Bioinspired Engineering and Biomechanics Center (BEBC), Xi' an Jiaotong University, Xi' an 710049 (China); The Key Laboratory of Biomedical Information Engineering of Ministry of Education, School of Life Science and Technology, Xi' an Jiaotong University, Xi' an 710049 (China); Lu, Tian Jian [Bioinspired Engineering and Biomechanics Center (BEBC), Xi' an Jiaotong University, Xi' an 710049 (China); Luo, Zhengtang, E-mail: keztluo@ust.hk [Department of Chemical and Biomolecular Engineering, Hong Kong University of Science and Technology, Clear Water Bay (Hong Kong)

    2016-04-21

    We demonstrate the fabrication of a graphene-based field effect transistor (GFET) incorporated in a two-dimensional paper network format (2DPNs). Paper serves as both a gate dielectric and an easy-to-fabricate vessel for holding the solution with the target molecules in question. The choice of paper enables a simpler alternative approach to the construction of a GFET device. The fabricated device is shown to behave similarly to a solution-gated GFET device with electron and hole mobilities of ∼1256 cm{sup 2} V{sup −1} s{sup −1} and ∼2298 cm{sup 2} V{sup −1} s{sup −1} respectively and a Dirac point around ∼1 V. When using solutions of ssDNA and glucose it was found that the added molecules induce negative electrolytic gating effects shifting the conductance minimum to the right, concurrent with increasing carrier concentrations which results to an observed increase in current response correlated to the concentration of the solution used. - Highlights: • A graphene-based field effect transistor sensor was fabricated for two-dimensional paper network formats. • The constructed GFET on 2DPN was shown to behave similarly to solution-gated GFETs. • Electrolyte gating effects have more prominent effect over adsorption effects on the behavior of the device. • The GFET incorporated on 2DPN was shown to yield linear response to presence of glucose and ssDNA soaked inside the paper.

  16. Electrical characterization of commercial NPN bipolar junction transistors under neutron and gamma irradiation

    Directory of Open Access Journals (Sweden)

    OO Myo Min

    2014-01-01

    Full Text Available Electronics components such as bipolar junction transistors, diodes, etc. which are used in deep space mission are required to be tolerant to extensive exposure to energetic neutrons and ionizing radiation. This paper examines neutron radiation with pneumatic transfer system of TRIGA Mark-II reactor at the Malaysian Nuclear Agency. The effects of the gamma radiation from Co-60 on silicon NPN bipolar junction transistors is also be examined. Analyses on irradiated transistors were performed in terms of the electrical characteristics such as current gain, collector current and base current. Experimental results showed that the current gain on the devices degraded significantly after neutron and gamma radiations. Neutron radiation can cause displacement damage in the bulk layer of the transistor structure and gamma radiation can induce ionizing damage in the oxide layer of emitter-base depletion layer. The current gain degradation is believed to be governed by the increasing recombination current in the base-emitter depletion region.

  17. Radiation induced deep level defects in bipolar junction transistors under various bias conditions

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chaoming; Yang, Jianqun [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Li, Xingji, E-mail: lxj0218@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Ma, Guoliang [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Xiao, Liyi [Department of Astronautics, Harbin Institute of Technology, Harbin 150001 (China); Bollmann, Joachim [Institute of Electronics and Sensor Materials, TU Bergakademie Freiberg, 71691 (Germany)

    2015-12-15

    Bipolar junction transistor (BJT) is sensitive to ionization and displacement radiation effects in space. In this paper, 35 MeV Si ions were used as irradiation source to research the radiation damage on NPN and PNP bipolar transistors. The changing of electrical parameters of transistors was in situ measured with increasing irradiation fluence of 35 MeV Si ions. Using deep level transient spectroscopy (DLTS), defects in the bipolar junction transistors under various bias conditions are measured after irradiation. Based on the in situ electrical measurement and DLTS spectra, it is clearly that the bias conditions can affect the concentration of deep level defects, and the radiation damage induced by heavy ions.

  18. Radiation induced deep level defects in bipolar junction transistors under various bias conditions

    Science.gov (United States)

    Liu, Chaoming; Yang, Jianqun; Li, Xingji; Ma, Guoliang; Xiao, Liyi; Bollmann, Joachim

    2015-12-01

    Bipolar junction transistor (BJT) is sensitive to ionization and displacement radiation effects in space. In this paper, 35 MeV Si ions were used as irradiation source to research the radiation damage on NPN and PNP bipolar transistors. The changing of electrical parameters of transistors was in situ measured with increasing irradiation fluence of 35 MeV Si ions. Using deep level transient spectroscopy (DLTS), defects in the bipolar junction transistors under various bias conditions are measured after irradiation. Based on the in situ electrical measurement and DLTS spectra, it is clearly that the bias conditions can affect the concentration of deep level defects, and the radiation damage induced by heavy ions.

  19. Silicon-on-insulator-based high-voltage, high-temperature integrated circuit gate driver for silicon carbide-based power field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Tolbert, Leon M [ORNL; Huque, Mohammad A [ORNL; Blalock, Benjamin J [ORNL; Islam, Syed K [ORNL

    2010-01-01

    Silicon carbide (SiC)-based field effect transistors (FETs) are gaining popularity as switching elements in power electronic circuits designed for high-temperature environments like hybrid electric vehicle, aircraft, well logging, geothermal power generation etc. Like any other power switches, SiC-based power devices also need gate driver circuits to interface them with the logic units. The placement of the gate driver circuit next to the power switch is optimal for minimising system complexity. Successful operation of the gate driver circuit in a harsh environment, especially with minimal or no heat sink and without liquid cooling, can increase the power-to-volume ratio as well as the power-to-weight ratio for power conversion modules such as a DC-DC converter, inverter etc. A silicon-on-insulator (SOI)-based high-voltage, high-temperature integrated circuit (IC) gate driver for SiC power FETs has been designed and fabricated using a commercially available 0.8--m, 2-poly and 3-metal bipolar-complementary metal oxide semiconductor (CMOS)-double diffused metal oxide semiconductor (DMOS) process. The prototype circuit-s maximum gate drive supply can be 40-V with peak 2.3-A sourcing/sinking current driving capability. Owing to the wide driving range, this gate driver IC can be used to drive a wide variety of SiC FET switches (both normally OFF metal oxide semiconductor field effect transistor (MOSFET) and normally ON junction field effect transistor (JFET)). The switching frequency is 20-kHz and the duty cycle can be varied from 0 to 100-. The circuit has been successfully tested with SiC power MOSFETs and JFETs without any heat sink and cooling mechanism. During these tests, SiC switches were kept at room temperature and ambient temperature of the driver circuit was increased to 200-C. The circuit underwent numerous temperature cycles with negligible performance degradation.

  20. Field effect transistor with HfO2/Parylene-C bilayer hybrid gate insulator

    Science.gov (United States)

    Kumar, Neeraj; Kito, Ai; Inoue, Isao

    2015-03-01

    We have investigated the electric field control of the carrier density and the mobility at the surface of SrTiO3, a well known transition-metal oxide, in a field effect transistor (FET) geometry. We have used a Parylene-C (8 nm)/HfO2 (20 nm) double-layer gate insulator (GI), which can be a potential candidate for a solid state GI for the future Mott FETs. So far, only examples of the Mott FET used liquid electrolyte or ferroelectric oxides for the GI. However, possible electrochemical reaction at the interface causes damage to the surface of the Mott insulator. Thus, an alternative GI has been highly desired. We observed that even an ultra thin Parylene-C layer is effective for keeping the channel surface clean and free from oxygen vacancies. The 8 nm Parylene-C film has a relatively low resistance and consequentially its capacitance does not dominate the total capacitance of the Parylene-C/HfO2 GI. The breakdown gate voltage at 300 K is usually more than 10 V (~ 3.4 MV/cm). At gate voltage of 3 V the carrier density measured by the Hall effect is about 3 ×1013 cm-2, competent to cause the Mott transition. Moreover, the field effect mobility reaches in the range of 10 cm2/Vs indicating the Parylene-C passivated surface is actually very clean.

  1. Fluorinated polyimide gate dielectrics for the advancing the electrical stability of organic field-effect transistors.

    Science.gov (United States)

    Baek, Yonghwa; Lim, Sooman; Yoo, Eun Joo; Kim, Lae Ho; Kim, Haekyoung; Lee, Seung Woo; Kim, Se Hyun; Park, Chan Eon

    2014-09-10

    Organic field-effect transistors (OFETs) that operated with good electrical stability were prepared by synthesizing fluorinated polyimide (PI) gate dielectrics based on 6FDA-PDA-PDA PI and 6FDA-CF3Bz-PDA PI. 6FDA-PDA-PDA PI and 6FDA-CF3Bz-PDA PI contain 6 and 18 fluorine atoms per repeat unit, respectively. These fluorinated polymers provided smooth surface topographies and surface energies that decreased as the number of fluorine atoms in the polymer backbone increased. These properties led to a better crystalline morphology in the semiconductor film grown over their surfaces. The number of fluorine atoms in the PI backbone increased, the field-effect mobility improved, and the threshold voltage shifted toward positive values (from -0.38 to +2.21 V) in the OFETs with pentacene and triethylsilylethynyl anthradithiophene. In addition, the highly fluorinated polyimide dielectric showed negligible hysteresis and a notable gate bias stability under both a N2 environment and ambient air.

  2. A sub kBT/q semimetal nanowire field effect transistor

    Science.gov (United States)

    Ansari, L.; Fagas, G.; Gity, F.; Greer, J. C.

    2016-08-01

    The key challenge for nanoelectronics technologies is to identify the designs that work on molecular length scales, provide reduced power consumption relative to classical field effect transistors (FETs), and that can be readily integrated at low cost. To this end, a FET is introduced that relies on the quantum effects arising for semimetals patterned with critical dimensions below 5 nm, that intrinsically has lower power requirements due to its better than a "Boltzmann tyranny" limited subthreshold swing (SS) relative to classical field effect devices, eliminates the need to form heterojunctions, and mitigates against the requirement for abrupt doping profiles in the formation of nanowire tunnel FETs. This is achieved through using a nanowire comprised of a single semimetal material while providing the equivalent of a heterojunction structure based on shape engineering to avail of the quantum confinement induced semimetal-to-semiconductor transition. Ab initio calculations combined with a non-equilibrium Green's function formalism for charge transport reveals tunneling behavior in the OFF state and a resonant conduction mechanism for the ON state. A common limitation to tunnel FET (TFET) designs is related to a low current in the ON state. A discussion relating to the semimetal FET design to overcome this limitation while providing less than 60 meV/dec SS at room temperature is provided.

  3. Flexible Organic/Inorganic Hybrid Field-Effect Transistors with High Performance and Operational Stability.

    Science.gov (United States)

    Dahiya, Abhishek S; Opoku, Charles; Poulin-Vittrant, Guylaine; Camara, Nicolas; Daumont, Christophe; Barbagiovanni, Eric G; Franzò, Giorgia; Mirabella, Salvo; Alquier, Daniel

    2017-01-11

    The production of high-quality semiconducting nanostructures with optimized electrical, optical, and electromechanical properties is important for the advancement of next-generation technologies. In this context, we herein report on highly obliquely aligned single-crystalline zinc oxide nanosheets (ZnO NSs) grown via the vapor-liquid-solid approach using r-plane (01-12) sapphire as the template surface. The high structural and optical quality of as-grown ZnO NSs has been confirmed using high-resolution transmission electron microscopy and temperature-dependent photoluminescence, respectively. To assess the potential of our NSs as effective building materials in high-performance flexible electronics, we fabricate organic (parylene C)/inorganic (ZnO NS) hybrid field-effect transistor (FET) devices on flexible substrates using room-temperature assembly processes. Extraction of key FET performance parameters suggests that as-grown ZnO NSs can successfully function as excellent n-type semiconducting modules. Such devices are found to consistently show very high on-state currents (Ion) > 40 μA, high field-effect mobility (μeff) > 200 cm(2)/(V s), exceptionally high on/off current modulation ratio (Ion/off) of around 10(9), steep subthreshold swing (s-s) low hysteresis, and negligible threshold voltage shifts with prolonged electrical stressing (up to 340 min). The present study delivers a concept of integrating high-quality ZnO NS as active semiconducting elements in flexible electronic circuits.

  4. Fabrication and Electrical Characteristics of Individual ZnO Submicron-Wire Field-Effect Transistor

    Institute of Scientific and Technical Information of China (English)

    JIANG Wei; GAO Hong; XU Ling-Ling

    2012-01-01

    Fabrication and electrical characteristics of individual ZnO submicro-wire field-effect transistors (FETs) are investigated by a simple micro-grid template method.The fabricated back-gate ZnO submicro-wire FET is characterized at room temperature in air.The gate voltage Vgs curves reveal gating effect characteristic of n-type conductivity.The field effect mobility of the ZnO submicro-wire is determined to be 7.9cm2/V.s at Vds =2 V,the capacitance and transconductance are estimated to be about 3.9fF and 15.5nS,respectively.UV sensitive property is measured using a 325-nm laser as the excitation source.Compared to the result carried in darkness,the ZnO submicro-wire FET is sensitive to UV irradiation,which indicates its potential application on UV detectors.Experimental results show that the approach introduced here allows the possibility of fabricating low-cost,reliable and flexible microelectronic devices.

  5. Di-electrophoresis assembly and fabrication of SWCNT field-effect transistor

    Institute of Scientific and Technical Information of China (English)

    TIAN XiaoJun; WANG YueChao; YU HaiBo; DONG ZaiLi; XI Ning; TUNG Steve

    2009-01-01

    In the process of fabricating nano electrical device or system based on single-walled carbon nanotube (SWCNT), the controllable assembly and fabrication of SWCNT field-effect transistor (SWCNT FET) is a key issue. SWCNT FET is the most basic and important component in nano electronics. After micro-electrode chip of back-gate FET is designed and fabricated, di-electrophoresis technology is adopted to realize the controllable alignment and assembly of SWCNTs, based on dispersing SWCNT by sodium dodecyl sulphate (SDS) facilitated ultra-sonication technique and removing impurities by centrifugal technique. The experiments of SWCNTs assembly demonstrate that SWCNTs are aligned and assem-bled uniformly at the microelectrodes gap with the alignment density nearly proportional to di-elec-trophoresis duration and solution concentration. After the processes of rinsing, drying and improving, metallic SWCNTs among the assembled SWCNTs are burned out and residual SDS is removed, and perfect field-effect performance of SWCNT FET is eventually obtained.

  6. Large-signal model of the bilayer graphene field-effect transistor targeting radio-frequency applications: Theory versus experiment

    Energy Technology Data Exchange (ETDEWEB)

    Pasadas, Francisco, E-mail: Francisco.Pasadas@uab.cat; Jiménez, David [Departament d' Enginyeria Electrònica, Escola d' Enginyeria, Universitat Autònoma de Barcelona, 08193 Bellaterra (Spain)

    2015-12-28

    Bilayer graphene is a promising material for radio-frequency transistors because its energy gap might result in a better current saturation than the monolayer graphene. Because the great deal of interest in this technology, especially for flexible radio-frequency applications, gaining control of it requires the formulation of appropriate models for the drain current, charge, and capacitance. In this work, we have developed them for a dual-gated bilayer graphene field-effect transistor. A drift-diffusion mechanism for the carrier transport has been considered coupled with an appropriate field-effect model taking into account the electronic properties of the bilayer graphene. Extrinsic resistances have been included considering the formation of a Schottky barrier at the metal-bilayer graphene interface. The proposed model has been benchmarked against experimental prototype transistors, discussing the main figures of merit targeting radio-frequency applications.

  7. Asymmetric Diketopyrrolopyrrole Conjugated Polymers for Field-Effect Transistors and Polymer Solar Cells Processed from a Nonchlorinated Solvent.

    Science.gov (United States)

    Ji, Yunjing; Xiao, Chengyi; Wang, Qiang; Zhang, Jianqi; Li, Cheng; Wu, Yonggang; Wei, Zhixiang; Zhan, Xiaowei; Hu, Wenping; Wang, Zhaohui; Janssen, René A J; Li, Weiwei

    2016-02-01

    Newly designed asymmetric diketopyrrolopyrrole conjugated polymers with two different aromatic substituents possess a hole mobility of 12.5 cm(2) V(-1) s(-1) in field-effect transistors and a power conversion efficiency of 6.5% in polymer solar cells, when solution processed from a nonchlorinated toluene/diphenyl ether mixed solvent.

  8. [Enzyme biosensors for penicillin determination based on conductometric planar electrodes and pH-sensitive field effect transistor].

    Science.gov (United States)

    Arkhipova, V N; Dziadevich, S V; Soldatkin, A P; El'skaia, A V

    1996-01-01

    The enzyme biosensors for penicillin determination based on conductometric planar electrodes and pH-sensitive field effect transistors have been described and their working parameters have been compared. The influence of pH, buffer capacity and ionic strength of the samples on the biosensors response has been studied. Short response time and high operational stability are characteristics of the developed biosensors.

  9. Controlling of the surface energy of the gate dielectric in organic field-effect transistors by polymer blend

    NARCIS (Netherlands)

    Gao, Jia; Asadi, Kamal; Xu, Jian Bin; An, Jin

    2009-01-01

    In this letter, we demonstrate that by blending insulating polymers, one can fabricate an insulating layer with controllable surface energy for organic field-effect transistors. As a model system, we used copper phthalocyanine evaporated on layers of polymethyl metacrylate blended with polystyrene w

  10. Manipulation of charge carrier injection into organic field-effect transistors by self-assembled monolayers of alkanethiols

    NARCIS (Netherlands)

    Asadi, K.; Gholamrezaie, F.; Smits, E.C.P.; Blom, W.M.; Boer, B. de

    2007-01-01

    Charge carrier injection into two semiconducting polymers is investigated in field-effect transistors using gold source and drain electrodes that are modified by self-assembled monolayers of alkanethiols and perfluorinated alkanethiols. The presence of an interfacial dipole associated with the molec

  11. Leveraging the ambipolar transport in polymeric field-effect transistors via blending with liquid-phase exfoliated graphene.

    Science.gov (United States)

    El Gemayel, Mirella; Haar, Sébastien; Liscio, Fabiola; Schlierf, Andrea; Melinte, Georgian; Milita, Silvia; Ersen, Ovidiu; Ciesielski, Artur; Palermo, Vincenzo; Samorì, Paolo

    2014-07-23

    Enhancement in the ambipolar behavior of field-effect transistors based on an n-type polymer, P(NDI2OD-T2), is obtained by co-deposition with liquid-phase exfoliated graphene. This approach provides a prospective pathway for the application of graphene-based nanocomposites for logic circuits.

  12. Modelling of Chirality-Dependent Current-Voltage Characteristics of Carbon-Nanotube Field-Effect Transistors

    Institute of Scientific and Technical Information of China (English)

    ZHAO Xu; WANG Yan; YU Zhi-Ping

    2006-01-01

    @@ Current-voltage characteristics of ballistic carbon-nanotube field-effect transistors are characterized with an it-erative simulation program. The influence of carbon-nanotube chirality and diameter on the output current is considered. An analytical current-voltage expression under the quantum capacitance limit and low-voltage application is derived. Our simulation results are compared with actual measurement data.

  13. Controlling of the surface energy of the gate dielectric in organic field-effect transistors by polymer blend

    NARCIS (Netherlands)

    Gao, Jia; Asadi, Kamal; Xu, Jian Bin; An, Jin

    2009-01-01

    In this letter, we demonstrate that by blending insulating polymers, one can fabricate an insulating layer with controllable surface energy for organic field-effect transistors. As a model system, we used copper phthalocyanine evaporated on layers of polymethyl metacrylate blended with polystyrene w

  14. High I on/I off current ratio graphene field effect transistor: the role of line defect.

    Science.gov (United States)

    Tajarrod, Mohammad Hadi; Saghai, Hassan Rasooli

    2015-01-01

    The present paper casts light upon the performance of an armchair graphene nanoribbon (AGNR) field effect transistor in the presence of one-dimensional topological defects. The defects containing 5-8-5 sp(2)-hybridized carbon rings were placed in a perfect graphene sheet. The atomic scale behavior of the transistor was investigated in the non-equilibrium Green's function (NEGF) and tight-binding Hamiltonian frameworks. AGNRFET basic terms such as the on/off current, transconductance and subthreshold swing were investigated along with the extended line defect (ELD). The results indicated that the presence of ELDs had a significant effect on the parameters of the GNRFET. Compared to conventional transistors, the increase of the I on/I off ratio in graphene transistors with ELDs enhances their applicability in digital devices.

  15. Touch sensors based on planar liquid crystal-gated-organic field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jooyeok; Lee, Chulyeon; Han, Hyemi; Lee, Sooyong; Nam, Sungho; Kim, Youngkyoo, E-mail: ykimm@knu.ac.kr [Organic Nanoelectronics Laboratory, Department of Chemical Engineering and Graduate School of Applied Chemical Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Kim, Hwajeong [Organic Nanoelectronics Laboratory, Department of Chemical Engineering and Graduate School of Applied Chemical Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Priority Research Center, Research Institute of Advanced Energy Technology, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Lee, Joon-Hyung [School of Materials Science and Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Park, Soo-Young; Kang, Inn-Kyu [Department of Polymer Science and Engineering and Graduate School of Applied Chemical Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of)

    2014-09-15

    We report a tactile touch sensor based on a planar liquid crystal-gated-organic field-effect transistor (LC-g-OFET) structure. The LC-g-OFET touch sensors were fabricated by forming the 10 μm thick LC layer (4-cyano-4{sup ′}-pentylbiphenyl - 5CB) on top of the 50 nm thick channel layer (poly(3-hexylthiophene) - P3HT) that is coated on the in-plane aligned drain/source/gate electrodes (indium-tin oxide - ITO). As an external physical stimulation to examine the tactile touch performance, a weak nitrogen flow (83.3 μl/s) was employed to stimulate the LC layer of the touch device. The LC-g-OFET device exhibited p-type transistor characteristics with a hole mobility of 1.5 cm{sup 2}/Vs, but no sensing current by the nitrogen flow touch was measured at sufficiently high drain (V{sub D}) and gate (V{sub G}) voltages. However, a clear sensing current signal was detected at lower voltages, which was quite sensitive to the combination of V{sub D} and V{sub G}. The best voltage combination was V{sub D} = −0.2 V and V{sub G} = −1 V for the highest ratio of signal currents to base currents (i.e., signal-to-noise ratio). The change in the LC alignment upon the nitrogen flow touch was assigned as the mechanism for the present LC-g-OFET touch sensors.

  16. Demonstration of high current carbon nanotube enabled vertical organic field effect transistors at industrially relevant voltages

    Science.gov (United States)

    McCarthy, Mitchell

    The display market is presently dominated by the active matrix liquid crystal display (LCD). However, the active matrix organic light emitting diode (AMOLED) display is argued to become the successor to the LCD, and is already beginning its way into the market, mainly in small size displays. But, for AMOLED technology to become comparable in market share to LCD, larger size displays must become available at a competitive price with their LCD counterparts. A major issue preventing low-cost large AMOLED displays is the thin-film transistor (TFT) technology. Unlike the voltage driven LCD, the OLEDs in the AMOLED display are current driven. Because of this, the mature amorphous silicon TFT backplane technology used in the LCD must be upgraded to a material possessing a higher mobility. Polycrystalline silicon and transparent oxide TFT technologies are being considered to fill this need. But these technologies bring with them significant manufacturing complexity and cost concerns. Carbon nanotube enabled vertical organic field effect transistors (CN-VFETs) offer a unique solution to this problem (now known as the AMOLED backplane problem). The CN-VFET allows the use of organic semiconductors to be used for the semiconductor layer. Organics are known for their low-cost large area processing compatibility. Although the mobility of the best organics is only comparable to that of amorphous silicon, the CN-VFET makes up for this by orienting the channel vertically, as opposed to horizontally (like in conventional TFTs). This allows the CN-VFET to achieve sub-micron channel lengths without expensive high resolution patterning. Additionally, because the CN-VFET can be easily converted into a light emitting transistor (called the carbon nanotube enabled vertical organic light emitting transistor---CN-VOLET) by essentially stacking an OLED on top of the CN-VFET, more potential benefits can be realized. These potential benefits include, increased aperture ratio, increased OLED

  17. Vertical field effect tunneling transistor based on graphene-ultrathin Si nanomembrane heterostructures

    Science.gov (United States)

    Das, Tanmoy; Jang, Houk; Bok Lee, Jae; Chu, Hyunwoo; Kim, Seong Dae; Ahn, Jong-Hyun

    2015-12-01

    Graphene-based heterostructured vertical transistors have attracted a great deal of research interest. Herein we propose a Si-based technology platform for creating graphene/ultrathin semiconductor/metal (GSM) junctions, which can be applied to large-scale and low-power electronics compatible with a variety of substrates. We fabricated graphene/Si nanomembrane (NM)/metal vertical heterostructures by using a dry transfer technique to transfer Si NMs onto chemical vapor deposition-grown graphene layers. The resulting van der Waals interfaces between graphene and p-Si NMs exhibited nearly ideal Schottky barrier behavior. Due to the low density of states of graphene, the graphene/Si NM Schottky barrier height can be modulated by modulating the band profile in the channel region, yielding well-defined current modulation. We obtained a maximum current on/off ratio (Ion/Ioff) of up to ˜103, with a current density of 102 A cm-2. We also observed significant dependence of Schottky barrier height Δφb on the thickness of the Si NMs. We confirmed that the transport in these devices is dominated by the effects of the graphene/Si NM Schottky barrier.

  18. Velocity overshoot decay mechanisms in compound semiconductor field-effect transistors with a submicron characteristic length

    Directory of Open Access Journals (Sweden)

    Jang Jyegal

    2015-06-01

    Full Text Available Velocity overshoot is a critically important nonstationary effect utilized for the enhanced performance of submicron field-effect devices fabricated with high-electron-mobility compound semiconductors. However, the physical mechanisms of velocity overshoot decay dynamics in the devices are not known in detail. Therefore, a numerical analysis is conducted typically for a submicron GaAs metal-semiconductor field-effect transistor in order to elucidate the physical mechanisms. It is found that there exist three different mechanisms, depending on device bias conditions. Specifically, at large drain biases corresponding to the saturation drain current (dc region, the velocity overshoot suddenly begins to drop very sensitively due to the onset of a rapid decrease of the momentum relaxation time, not the mobility, arising from the effect of velocity-randomizing intervalley scattering. It then continues to drop rapidly and decays completely by severe mobility reduction due to intervalley scattering. On the other hand, at small drain biases corresponding to the linear dc region, the velocity overshoot suddenly begins to drop very sensitively due to the onset of a rapid increase of thermal energy diffusion by electrons in the channel of the gate. It then continues to drop rapidly for a certain channel distance due to the increasing thermal energy diffusion effect, and later completely decays by a sharply decreasing electric field. Moreover, at drain biases close to a dc saturation voltage, the mechanism is a mixture of the above two bias conditions. It is suggested that a large secondary-valley energy separation is essential to increase the performance of submicron devices.

  19. Using Animation to Improve the Students' Academic Achievement on Bipolar Junction Transistor

    Science.gov (United States)

    Zoabi, W.; Sabag, N.; Gero, A.

    2012-01-01

    Teaching abstract subjects to students studying towards a degree in electronics practical engineering (a degree between a technician and an engineer) requires didactic tools that enable understanding of issues without using advanced mathematics and physics. One basic issue is the BJT (Bipolar Junction Transistor) that requires preliminary…

  20. Radiation defects studies on silicon bipolar junction transistor irradiated by Br ions and electrons

    Science.gov (United States)

    Liu, Chaoming; Li, Xingji; Yang, Jianqun; Ma, Guoliang; Xiao, Liyi; Bollmann, Joachim

    2015-12-01

    Bipolar junction transistors are sensitive to both ionization and displacement damage due to charged particles from space radiation. Passivating oxides and the SiO2/Si interface are more sensitive to ionization damage whereas displacement damage may strongly influence the bulk properties of a device. Fast electrons with energies below a few MeV introduces exclusively target ionization while heavy ions at moderate energies (lower than 2 MeV/amu) results in displacement damage due to individual Frenkel-pairs generation. Although both kinds of radiation are basically independent an effective correlation was seen in the electronic characteristics of transistors. We report on the effects on current gain and current-voltage characteristics of bipolar junction transistors due to successive irradiation with 20 MeV Br ions and 110 keV electrons.

  1. The Helium Field Effect Transistor (I): Storing Surface State Electrons on Helium Films

    Science.gov (United States)

    Ashari, M.; Rees, D. G.; Kono, K.; Scheer, E.; Leiderer, P.

    2012-04-01

    We present investigations of surface state electrons on liquid helium films in confined geometry, using a suitable substrate structure microfabricated on a silicon wafer, similar to a Field Effect Transistor (FET). The sample has a source and drain region, separated by a gate structure, which consists of two gold electrodes with a narrow gap (channel) through which the transport of the surface state electrons takes place. The sample is illuminated to provide a sufficient number of free carriers in the silicon substrate, such that a well-defined potential distribution is achieved. The eventual goal of these experiments is to study the electron transport through a narrow channel in the various states of the phase diagram of the 2D electron system. In the present work we focus on storing the electrons in the source area of the FET, and investigate the spatial distribution of these electrons. It is shown that under the influence of a potential gradient in the silicon substrate the electrons accumulate in front of the potential barrier of the gate. The electron distribution, governed by Coulomb repulsion and by the substrate potential, is determined experimentally. The result is found to be in good agreement with a parallel-plate capacitor model of the system, developed with the aid of a finite element calculation of the surface potential profile of the device.

  2. H-terminated diamond field effect transistor with ferroelectric gate insulator

    Energy Technology Data Exchange (ETDEWEB)

    Karaya, Ryota; Furuichi, Hiroki [Graduate School of Natural Science and Technology, Kanazawa University, Kanazawa, Ishikawa 920-1155 (Japan); Nakajima, Takashi [Department of Applied Physics, Tokyo University of Science, Katsushika-ku, Tokyo 125-8585 (Japan); Tokuda, Norio; Kawae, Takeshi, E-mail: kawae@ec.t.kanazawa-u.ac.jp [College of Science and Engineering, Kanazawa University, Kanazawa, Ishikawa 920-1155 (Japan)

    2016-06-13

    An H-terminated diamond field-effect-transistor (FET) with a ferroelectric vinylidene fluoride (VDF)-trifluoroethylene (TrFE) copolymer gate insulator was fabricated. The VDF-TrFE film was deposited on the H-terminated diamond by the spin-coating method and low-temperature annealing was performed to suppress processing damage to the H-terminated diamond surface channel layer. The fabricated FET structure showed the typical properties of depletion-type p-channel FET and showed clear saturation of the drain current with a maximum value of 50 mA/mm. The drain current versus gate voltage curves of the proposed FET showed clockwise hysteresis loops due to the ferroelectricity of the VDF-TrFE gate insulator, and the memory window width was 19 V, when the gate voltage was swept from 20 to −20 V. The maximum on/off current ratio and the linear mobility were 10{sup 8} and 398 cm{sup 2}/V s, respectively. In addition, we modulated the drain current of the fabricated FET structure via the remnant polarization of the VDF-TrFE gate and obtained an on/off current ratio of 10{sup 3} without applying a DC gate voltage.

  3. Downscaling ferroelectric field effect transistors by using ferroelectric Si-doped HfO2

    Science.gov (United States)

    Martin, Dominik; Yurchuk, Ekaterina; Müller, Stefan; Müller, Johannes; Paul, Jan; Sundquist, Jonas; Slesazeck, Stefan; Schlösser, Till; van Bentum, Ralf; Trentzsch, Martin; Schröder, Uwe; Mikolajick, Thomas

    2013-10-01

    Throughout the 22 nm technology node HfO2 is established as a reliable gate dielectric in contemporary complementary metal oxide semiconductor (CMOS) technology. The working principle of ferroelectric field effect transistors FeFET has also been demonstrated for some time for dielectric materials like Pb[ZrxTi1-x]O3 and SrBi2Ta2O9. However, integrating these into contemporary downscaled CMOS technology nodes is not trivial due to the necessity of an extremely thick gate stack. Recent developments have shown HfO2 to have ferroelectric properties, given the proper doping. Moreover, these doped HfO2 thin films only require layer thicknesses similar to the ones already in use in CMOS technology. This work will show how the incorporation of Si induces ferroelectricity in HfO2 based capacitor structures and finally demonstrate non-volatile storage in nFeFETs down to a gate length of 100 nm. A memory window of 0.41 V can be retained after 20,000 switching cycles. Retention can be extrapolated to 10 years.

  4. Field-effect transistors of high-mobility few-layer SnSe2

    Science.gov (United States)

    Guo, Chenglei; Tian, Zhen; Xiao, Yanjun; Mi, Qixi; Xue, Jiamin

    2016-11-01

    We report the transport properties of mechanically exfoliated few-layer SnSe2 flakes, whose mobility is found to be ˜85 cm2 V-1 s-1 at 300 K, higher than those of the majority of few-layer transitional metal dichalcogenides. The mobility increases strongly with decreased temperature, indicating a phonon limited transport. The conductivity of the semiconducting SnSe2 shows a metallic behavior, which is explained by two competing factors involving the different temperature dependence of mobility and carrier density. The Fermi level is found to be 87 meV below the conduction band minima (CBM) at 300 K and 12 meV below the CBM at 78 K, resulting from a heavy n-type doping. Previous studies have found SnSe2 field-effect transistors to be very difficult to turn off. We find the limiting factor to be the flake thickness compared with the maximum depletion width. With fully depleted devices, we are able to achieve a current on-off ratio of ˜105. These results demonstrate the great potential of SnSe2 as a two dimensional (2D) semiconducting material and are helpful for our understanding of other heavily doped 2D materials.

  5. A high sensitivity field effect transistor biosensor for methylene blue detection utilize graphene oxide nanoribbon.

    Science.gov (United States)

    Lin, Ting-Chun; Li, Yan-Sheng; Chiang, Wei-Hung; Pei, Zingway

    2017-03-15

    In this work, we developed a field effect transistor (FET) biosensor utilizing solution-processed graphene oxide nanoribbon (GONR) for methylene blue (MB) sensing. MB is a unique material; one of its crucial applications is as a marker in the detection of biomaterials. Therefore, a highly sensitive biosensor with a low detection limit that can be fabricated simply in a noncomplex detection scheme is desirable. GONR is made by unzipping multiwall carbon nanotubes, which can be mass-produced at low temperature. The GONR-FET biosensor demonstrated a sensitivity of 12.5μA/mM (determined according to the drain current difference caused by the MB concentration change). The Raman spectra indicate that the materials quality of the GONR and the domain size for the C=C sp(2) bonding were both improved after MB detection. X-ray photoelectron spectroscopy revealed that the hydroxyl groups on the GONR were removed by the reductive MB. According to XPS and Raman, the positive charge is proposed to transfer from MB to GONR during sensing. This transfer causes charge in-neutrality in the GONR which is compensated by releasing •OH functional groups. With high sensitivity, a low detection limit, and a simple device structure, the GONR-FET sensor is suitable for sensing biomaterials.

  6. Vacuum-and-solvent-free fabrication of organic semiconductor layers for field-effect transistors

    Science.gov (United States)

    Matsushima, Toshinori; Sandanayaka, Atula S. D.; Esaki, Yu; Adachi, Chihaya

    2015-09-01

    We demonstrate that cold and hot isostatic pressing (CIP and HIP) is a novel, alternative method for organic semiconductor layer fabrication, where organic powder is compressed into a layer shape directly on a substrate with 200 MPa pressure. Spatial gaps between powder particles and the other particles, substrates, or electrodes are crushed after CIP and HIP, making it possible to operate organic field-effect transistors (OFETs) containing the compressed powder as the semiconductor. The CIP-compressed powder of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) had a hole mobility of (1.6 ± 0.4) × 10-2 cm2/Vs. HIP of C8-BTBT powder increased the hole mobility to an amorphous silicon-like value (0.22 ± 0.07 cm2/Vs) because of the growth of the C8-BTBT crystallites and the improved continuity between the powder particles. The vacuum and solution processes are not involved in our CIP and HIP techniques, offering a possibility of manufacturing OFETs at low cost.

  7. Diameter dependence of 1/f noise in carbon nanotube field effect transistors using noise spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, Toshio, E-mail: toshi@isc.chubu.ac.jp [Center of Applied Superconductivity and Sustainable Energy Research, Chubu University, 1200, Matsumoto-cho, Kasugai-shi, Aichi 487-8501 (Japan); Yamaguchi, Satarou [Center of Applied Superconductivity and Sustainable Energy Research, Chubu University, 1200, Matsumoto-cho, Kasugai-shi, Aichi 487-8501 (Japan); Ohno, Yasuhide; Maehashi, Kenzo; Matsumoto, Kazuhiko [The Institute of Scientific and Industrial Research, Osaka University, 8-1, Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Mizutani, Shin [NTT Communication Science Laboratories, 2-4, Hikaridai Seika-cho, Soraku-gun, Kyoto 619-0237 (Japan); Itaka, Kenji [North Japan Research Institute for Sustainable Energy, Hirosaki University, 2-1-3 Matsubara, Aomori 030-0813 (Japan)

    2013-02-15

    Carbon nanotubes (CNTs) have many interesting properties for nano devices such as high sensitive sensors or noise enhanced nonlinear devices. A field effect transistor (FET) structure is one of the key features for these applications, and the control of noise in FETs is important for the actual operation of the application. Several origins of noise have been proposed, and defects and/or surface adsorption of molecules seem to be dominant for the 1/f type noise in CNTs. To study the origins of noise, the diameter dependence of noise properties was studied. We analyzed the noise properties in CNTs using noise spectroscopy with different fabrication parameters or ambient environments. We observed the crossover of noise properties in CNTs, which involved transition between different origins of noise depending on their diameter. Additionally, noise spectroscopy was used to observe such crossover between air and vacuum environments. We can control noise intensity using the gate voltage, and noise properties can be controlled by the fabrication parameters. These phenomena are useful for the stochastic operation of CNT-FETs.

  8. Fabrication and characterization of junctionless carbon nanotube field effect transistor for cholesterol detection

    Science.gov (United States)

    Barik, Md. Abdul; Dutta, Jiten Ch.

    2014-08-01

    We have reported fabrication and characterization of polyaniline (PANI)/zinc oxide (ZnO) membrane-based junctionless carbon nanotube field effect transistor deposited on indium tin oxide glass plate for the detection of cholesterol (0.5-22.2 mM). Cholesterol oxidase (ChOx) has been immobilized on the PANI/ZnO membrane by physical adsorption technique. Electrical response has been recorded using digital multimeter (Agilent 3458A) in the presence of phosphate buffer saline of 50 mM, pH 7.0, and 0.9% NaCl contained in a glass pot. The results of response studies for cholesterol reveal linearity as 0.5-16.6 mM and improved sensitivity of 60 mV/decade in good agreement with Nernstian limit ˜59.2 mV/decade. The life time of this sensor has been found up to 5 months and response time of 1 s. The limit of detection with regression coefficient (r) ˜ 0.998 and Michaelis-Menten constant (Km) were found to be ˜0.25 and 1.4 mM, respectively, indicating high affinity of ChOx to cholesterol. The results obtained in this work show negligible interference with glucose and urea.

  9. Fabrication and characterization of junctionless carbon nanotube field effect transistor for cholesterol detection

    Energy Technology Data Exchange (ETDEWEB)

    Barik, Md. Abdul, E-mail: abdulnpl@gmail.com; Dutta, Jiten Ch. [Department of Electronics and Communication Engineering, Tezpur University, Napaam, Tezpur, Assam 784028 (India)

    2014-08-04

    We have reported fabrication and characterization of polyaniline (PANI)/zinc oxide (ZnO) membrane-based junctionless carbon nanotube field effect transistor deposited on indium tin oxide glass plate for the detection of cholesterol (0.5–22.2 mM). Cholesterol oxidase (ChOx) has been immobilized on the PANI/ZnO membrane by physical adsorption technique. Electrical response has been recorded using digital multimeter (Agilent 3458A) in the presence of phosphate buffer saline of 50 mM, pH 7.0, and 0.9% NaCl contained in a glass pot. The results of response studies for cholesterol reveal linearity as 0.5–16.6 mM and improved sensitivity of 60 mV/decade in good agreement with Nernstian limit ∼59.2 mV/decade. The life time of this sensor has been found up to 5 months and response time of 1 s. The limit of detection with regression coefficient (r) ∼ 0.998 and Michaelis-Menten constant (K{sub m}) were found to be ∼0.25 and 1.4 mM, respectively, indicating high affinity of ChOx to cholesterol. The results obtained in this work show negligible interference with glucose and urea.

  10. Highly Uniform Carbon Nanotube Field-Effect Transistors and Medium Scale Integrated Circuits.

    Science.gov (United States)

    Chen, Bingyan; Zhang, Panpan; Ding, Li; Han, Jie; Qiu, Song; Li, Qingwen; Zhang, Zhiyong; Peng, Lian-Mao

    2016-08-10

    Top-gated p-type field-effect transistors (FETs) have been fabricated in batch based on carbon nanotube (CNT) network thin films prepared from CNT solution and present high yield and highly uniform performance with small threshold voltage distribution with standard deviation of 34 mV. According to the property of FETs, various logical and arithmetical gates, shifters, and d-latch circuits were designed and demonstrated with rail-to-rail output. In particular, a 4-bit adder consisting of 140 p-type CNT FETs was demonstrated with higher packing density and lower supply voltage than other published integrated circuits based on CNT films, which indicates that CNT based integrated circuits can reach to medium scale. In addition, a 2-bit multiplier has been realized for the first time. Benefitted from the high uniformity and suitable threshold voltage of CNT FETs, all of the fabricated circuits based on CNT FETs can be driven by a single voltage as small as 2 V.

  11. Infrared study of charge injection in organic field-effect transistors

    Science.gov (United States)

    Li, Zhiqiang

    2008-03-01

    We present a systematic infrared (IR) spectroscopic study of charge injection in organic field-effect transistors (FET). These experiments have revealed new unexpected aspects of both polymers and molecular crystals. IR spectromicroscopy was employed to image the charges in poly(3-hexylthiophene) (P3HT) FETs. The charge density profile in the conducting channel uncovers a density-dependent mobility in P3HT due to disorder effects. Our IR studies of single crystal rubrene based FETs show that charge transport in these devices at room temperature is governed by light quasiparticles in molecular orbital bands. This result is at variance with the common beliefs of polaron formation in molecular solids. The above experiments have demonstrated the unique potential of IR spectroscopy for investigating physical phenomena at the nanoscale occurring at the semiconductor-insulator interface in FET devices. This work is in collaboration with G. M. Wang, D. Moses, A. J. Heeger (UCSB), V. Podzorov, M.E. Gershenson (Rutgers), Z. Hao, M. C. Martin (ALS), N. Sai, A. D. Meyertholen, M. M. Fogler, M. Di Ventra and D. N. Basov (UCSD).

  12. Charge neutral MoS2 field effect transistors through oxygen plasma treatment

    Science.gov (United States)

    Dhall, Rohan; Li, Zhen; Kosmowska, Ewa; Cronin, Stephen B.

    2016-11-01

    Lithographically fabricated MoS2 field effect transistors suffer from several critical imperfections, including low sub-threshold swings, large turn-on gate voltages (VT), and wide device-to-device variability. The large magnitude and variability of VT stems from unclean interfaces, trapped charges in the underlying substrate, and sulfur vacancies created during the mechanical exfoliation process. In this study, we demonstrate a simple and reliable oxygen plasma treatment, which mitigates the effects of unintentional doping created by surface defect sites, such as S vacancies, and surface contamination. This plasma treatment restores charge neutrality to the MoS2 and shifts the threshold turn-on voltage towards 0 V. Out of the 10 devices measured, all exhibit a shift of the FET turn-on voltage from an average of -18 V to -2 V. The oxygen plasma treatment passivates these defects, which reduces surface scattering, causing increased mobility and improved subthreshold swing. For as-prepared devices with low mobilities (˜0.01 cm2/V s), we observe up to a 190-fold increase in mobility after exposure to the oxygen plasma. Perhaps the most important aspect of this oxygen plasma treatment is that it reduces the device-to-device variability, which is a crucial factor in realizing any practical application of these devices.

  13. Advances in MoS2-Based Field Effect Transistors (FETs)

    Institute of Scientific and Technical Information of China (English)

    Xin Tong; Eric Ashalley; Feng Lin; Handong Li; Zhiming M. Wang

    2015-01-01

    This paper reviews the original achievements and advances regarding the field effect transistor (FET) fabricated from one of the most studied transition metal dichalcogenides: two-dimensional MoS2. Not like graphene, which is highlighted by a gapless Dirac cone band structure, Monolayer MoS2 is featured with a 1.9 eV gapped direct energy band thus facilitates convenient electronic and/or optoelectronic modulation of its physical properties in FET structure. Indeed, many MoS2 devices based on FET architecture such as phototransistors, memory devices, and sensors have been studied and extraordinary properties such as excellent mobility, ON/OFF ratio, and sensitivity of these devices have been ex-hibited. However, further developments in FET device applications depend a lot on if novel physics would be involved in them. In this review, an overview on advances and developments in the MoS2-based FETs are presented. Engineering of MoS2-based FETs will be discussed in details for understanding contact physics, formation of gate dielectric, and doping strategies. Also reported are demonstrations of device behaviors such as low-frequency noise and photoresponse in MoS2-based FETs, which is crucial for developing electronic and optoelectronic devices.

  14. Temperature Dependence of Electrical Characteristics of Carbon Nanotube Field-Effect Transistors: A Quantum Simulation Study

    Directory of Open Access Journals (Sweden)

    Ali Naderi

    2012-01-01

    Full Text Available By developing a two-dimensional (2D full quantum simulation, the attributes of carbon nanotube field-effect transistors (CNTFETs in different temperatures have been comprehensively investigated. Simulations have been performed by employing the self-consistent solution of 2D Poisson-Schrödinger equations within the nonequilibrium Green's function (NEGF formalism. Principal characteristics of CNTFETs such as current capability, drain conductance, transconductance, and subthreshold swing (SS have been investigated. Simulation results present that as temperature raises from 250 to 500 K, the drain conductance and on-current of the CNTFET improved; meanwhile the on-/off-current ratio deteriorated due to faster growth in off-current. Also the effects of temperature on short channel effects (SCEs such as drain-induced barrier lowering (DIBL and threshold voltage roll-off have been studied. Results show that the subthreshold swing and DIBL parameters are almost linearly correlated, so the degradation of these parameters has the same origin and can be perfectly influenced by the temperature.

  15. Solution-processible organic-inorganic hybrid bipolar field-effect transistors

    Science.gov (United States)

    Chae, Gil Jo; Kim, Kang Dae; Cho, Shinuk; Walker, Bright; Seo, Jung Hwa

    2016-04-01

    Organic-inorganic hybrid bipolar field-effect transistors (HBFETs) comprising a layer of p-type organic poly(3-hexylthiophene) (P3HT) separated from a parallel layer of n-type inorganic zinc oxide (ZnO) were demonstrated by solution processing. In order to achieve balanced hole and electron mobilities, we initially optimized the hole-transporting P3HT channel by the addition of the polar non-solvent acetonitrile (AN) to P3HT solutions in chloroform, which induced a selfassembled nano-fibril morphology and an enhancement of hole mobilities. For the electron channel, a wet-chemically-prepared ZnO layer was optimized by thermal annealing. Unipolar P3HT FET with 5% AN exhibited the highest hole mobility of 7.20 × 10-2 cm2V-1s-1 while the highest electron mobility (3.64 × 10-2 cm2V-1s-1) was observed in unipolar ZnO FETs annealed at 200°C. The organic-inorganic HBFETs consisting of the P3HT layer with 5% AN and ZnO annealed at 200°C exhibited well-balanced hole and electron mobilities of 1.94 × 10-2 cm2V-1s-1 and 1.98 × 10-2 cm2V-1s-1, respectively.

  16. Current trends in nanomaterial embedded field effect transistor-based biosensor.

    Science.gov (United States)

    Nehra, Anuj; Pal Singh, Krishna

    2015-12-15

    Recently, as metal-, polymer-, and carbon-based biocompatible nanomaterials have been increasingly incorporated into biosensing applications, with various nanostructures having been used to increase the efficacy and sensitivity of most of the detecting devices, including field effect transistor (FET)-based devices. These nanomaterial-based methods also became the ideal for the amalgamation of biomolecules, especially for the fabrication of ultrasensitive, low-cost, and robust FET-based biosensors; these are categorically very successful at binding the target specified entities in the confined gated micro-region for high functionality. Furthermore, the contemplation of nanomaterial-based FET biosensors to various applications encompasses the desire for detection of many targets with high selectivity, and specificity. We assess how such devices have empowered the achievement of elevated biosensor performance in terms of high sensitivity, selectivity and low detection limits. We review the recent literature here to illustrate the diversity of FET-based biosensors, based on various kinds of nanomaterials in different applications and sum up that graphene or its assisted composite based FET devices are comparatively more efficient and sensitive with highest signal to noise ratio. Lastly, the future prospects and limitations of the field are also discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Graphene Channel Liquid Container Field Effect Transistor as pH Sensor

    Directory of Open Access Journals (Sweden)

    Xin Li

    2014-01-01

    Full Text Available Graphene channel liquid container field effect transistor pH sensor with interdigital microtrench for liquid ion testing is presented. Growth morphology and pH sensing property of continuous few-layer graphene (FLG and quasi-continuous monolayer graphene (MG channels are compared. The experiment results show that the source-to-drain current of the graphene channel FET has a significant and fast response after adsorption of the measured molecule and ion at the room temperature; at the same time, the FLG response time is less than 4 s. The resolution of MG (0.01 on pH value is one order of magnitude higher than that of FLG (0.1. The reason is that with fewer defects, the MG is more likely to adsorb measured molecule and ion, and the molecules and ions can make the transport property change. The output sensitivities of MG are from 34.5% to 57.4% when the pH value is between 7 and 8, while sensitivity of FLG is 4.75% when the pH=7. The sensor fabrication combines traditional silicon technique and flexible electronic technology and provides an easy way to develop graphene-based electrolyte gas sensor or even biological sensors.

  18. Organic nanofibers integrated by transfer technique in field-effect transistor devices

    Directory of Open Access Journals (Sweden)

    Tavares Luciana

    2011-01-01

    Full Text Available Abstract The electrical properties of self-assembled organic crystalline nanofibers are studied by integrating these on field-effect transistor platforms using both top and bottom contact configurations. In the staggered geometries, where the nanofibers are sandwiched between the gate and the source-drain electrodes, a better electrical conduction is observed when compared to the coplanar geometry where the nanofibers are placed over the gate and the source-drain electrodes. Qualitatively different output characteristics were observed for top and bottom contact devices reflecting the significantly different contact resistances. Bottom contact devices are dominated by contact effects, while the top contact device characteristics are determined by the nanofiber bulk properties. It is found that the contact resistance is lower for crystalline nanofibers when compared to amorphous thin films. These results shed light on the charge injection and transport properties for such organic nanostructures and thus constitute a significant step forward toward a nanofiber-based light-emitting device.

  19. The intrinsic origin of hysteresis in MoS2 field effect transistors.

    Science.gov (United States)

    Shu, Jiapei; Wu, Gongtao; Guo, Yao; Liu, Bo; Wei, Xianlong; Chen, Qing

    2016-02-07

    We investigate the hysteresis and gate voltage stress effect in MoS2 field effect transistors (FETs). We observe that both the suspended and the SiO2-supported FETs have large hysteresis in their transfer curves under vacuum which cannot be attributed to the traps at the interface between the MoS2 and the SiO2 or in the SiO2 substrate or the gas adsorption/desorption effect. Our findings indicate that the hysteresis we observe comes from the MoS2 itself, revealing an intrinsic origin of the hysteresis besides some extrinsic factors. The fact that the FETs based on thinner MoS2 have larger hysteresis than that with thicker MoS2 suggests that the surface of MoS2 plays a key role in the hysteresis. The gate voltage sweep range, sweep direction, sweep time and loading history all affect the hysteresis observed in the transfer curves.

  20. Highly photosensitive graphene field-effect transistor with optical memory function

    Science.gov (United States)

    Ishida, Shohei; Anno, Yuki; Takeuchi, Masato; Matsuoka, Masaya; Takei, Kuniharu; Arie, Takayuki; Akita, Seiji

    2015-10-01

    Graphene is a promising material for use in photodetectors for the ultrawide wavelength region: from ultraviolet to terahertz. Nevertheless, only the 2.3% light absorption of monolayer graphene and fast recombination time of photo-excited charge restrict its sensitivity. To enhance the photosensitivity, hybridization of photosensitive material and graphene has been widely studied, where the accumulated photo-excited charge adjacent to the graphene channel modifies the Fermi level of graphene. However, the charge accumulation process slows the response to around a few tens of seconds to minutes. In contrast, a charge accumulation at the contact would induce the efficient light-induced modification of the contact resistance, which would enhance its photosensitivity. Herein, we demonstrate a highly photosensitive graphene field-effect transistor with noise-equivalent power of ~3 × 10-15 W/Hz1/2 and with response time within milliseconds at room temperature, where the Au oxide on Au electrodes modulates the contact resistance because of the light-assisted relaxation of the trapped charge at the contact. Additionally, this light-induced relaxation imparts an optical memory function with retention time of ~5 s. These findings are expected to open avenues to realization of graphene photodetectors with high sensitivity toward single photon detection with optical memory function.

  1. Graphene field-effect transistors with tunable sensitivity for high performance Hg (II) sensing

    Science.gov (United States)

    Li, Peng; Liu, Baijun; Zhang, Dongzhi; Sun, Yan'e.; Liu, Jingjing

    2016-10-01

    Graphene field-effect transistors (FETs) capped with ionophore were fabricated to demonstrate the highly sensitive and selective detection of Hg (II) ions in solution. We systematically investigated the ion detection performances and sensing mechanism of this 2D material. Due to its ambipolar nature, graphene can work as either an n-type or a p-type sensor when a gate voltage is applied to switch its carrier characteristic, resulting in completely different sensing performances. The strong dependence of sensitivity on gate voltage was also investigated. Graphene FETs in optimal regimes were able to detect Hg2+ down to 0.1 ppb, one-fold lower than the World Health Organization tolerance level. Hg2+ ions can be effectively detected over a wide range of concentration (from 0.1 ppb to 1000 ppb) with graphene conductance change following the Langmuir isotherm for molecules adsorption on surface, and the time constant for ion adsorption extracted was only 3.5 s, approximately. The transfer characteristics of graphene FETs capped with mercury ionophore did not show obvious change by the existence of arsenite ions, demonstrating good selectivity. Our results illustrate the potential utility of ionophore integrated graphene FETs for monitoring heavy metal ions in solution.

  2. Targeting Antibodies to Carbon Nanotube Field Effect Transistors by Pyrene Hydrazide Modification of Heavy Chain Carbohydrates

    Directory of Open Access Journals (Sweden)

    Steingrimur Stefansson

    2012-01-01

    Full Text Available Many carbon nanotube field-effect transistor (CNT-FET studies have used immobilized antibodies as the ligand binding moiety. However, antibodies are not optimal for CNT-FET detection due to their large size and charge. Their size can prevent ligands from reaching within the Debye length of the CNTs and a layer of charged antibodies on the circuits can drown out any ligand signal. In an attempt to minimize the antibody footprint on CNT-FETs, we examined whether pyrene hydrazide modification of antibody carbohydrates could reduce the concentration required to functionalize CNT circuits. The carbohydrates are almost exclusively on the antibody Fc region and this site-specific modification could mediate uniform antibody orientation on the CNTs. We compared the hydrazide modification of anti-E. coli O157:H7 polyclonal antibodies to pyrenebutanoic acid succinimidyl ester-coated CNTs and carbodiimide-mediated antibody CNT attachment. Our results show that the pyrene hydrazide modification was superior to those methods with respect to bacteria detection and less than 1 nM labeled antibody was required to functionalize the circuits.

  3. High-Throughput Peptide Epitope Mapping Using Carbon Nanotube Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Steingrimur Stefansson

    2013-01-01

    Full Text Available Label-free and real-time detection technologies can dramatically reduce the time and cost of pharmaceutical testing and development. However, to reach their full promise, these technologies need to be adaptable to high-throughput automation. To demonstrate the potential of single-walled carbon nanotube field-effect transistors (SWCNT-FETs for high-throughput peptide-based assays, we have designed circuits arranged in an 8 × 12 (96-well format that are accessible to standard multichannel pipettors. We performed epitope mapping of two HIV-1 gp160 antibodies using an overlapping gp160 15-mer peptide library coated onto nonfunctionalized SWCNTs. The 15-mer peptides did not require a linker to adhere to the non-functionalized SWCNTs, and binding data was obtained in real time for all 96 circuits. Despite some sequence differences in the HIV strains used to generate these antibodies and the overlapping peptide library, respectively, our results using these antibodies are in good agreement with known data, indicating that peptides immobilized onto SWCNT are accessible and that linear epitope mapping can be performed in minutes using SWCNT-FET.

  4. Flexible Graphene Field-Effect Transistors Encapsulated in Hexagonal Boron Nitride.

    Science.gov (United States)

    Petrone, Nicholas; Chari, Tarun; Meric, Inanc; Wang, Lei; Shepard, Kenneth L; Hone, James

    2015-09-22

    Flexible graphene field-effect transistors (GFETs) are fabricated with graphene channels fully encapsulated in hexagonal boron nitride (hBN) implementing a self-aligned fabrication scheme. Flexible GFETs fabricated with channel lengths of 2 μm demonstrate exceptional room-temperature carrier mobility (μFE = 10 000 cm(2) V(-1) s(-1)), strong current saturation characteristics (peak output resistance, r0 = 2000 Ω), and high mechanical flexibility (strain limits of 1%). These values of μFE and r0 are unprecedented in flexible GFETs. Flexible radio frequency FETs (RF-FETs) with channel lengths of 375 nm demonstrate μFE = 2200 cm(2) V(-1) s(-1) and r0 = 132.5 Ω. Unity-current gain frequencies, fT, and unity-power gain frequencies, fmax, reach 12.0 and 10.6 GHz, respectively. The corresponding ratio of cutoff frequencies approaches unity (fmax/fT = 0.9), a record value for flexible GFETs. Intrinsic fT and fmax are 29.7 and 15.7 GHz, respectively. The outstanding electronic characteristics are attributed to the improved dielectric environment provided by full hBN encapsulation of the graphene channel in conjunction with an optimized, self-aligned device structure. These results establish hBN as a mechanically robust dielectric that can yield enhanced electronic characteristics to a diverse array of graphene-based flexible electronics.

  5. Detection of heart failure-related biomarker in whole blood with graphene field effect transistor biosensor.

    Science.gov (United States)

    Lei, Yong-Min; Xiao, Meng-Meng; Li, Yu-Tao; Xu, Li; Zhang, Hong; Zhang, Zhi-Yong; Zhang, Guo-Jun

    2017-05-15

    Since brain natriuretic peptide (BNP) has become internationally recognized biomarkers in the diagnosis and prognosis of heart failure (HF), it is highly desirable to search for a novel sensing tool for detecting the patient's BNP level at the early stage. Here we report a platinum nanoparticles (PtNPs)-decorated reduced graphene oxide (rGO) field effect transistor (FET) biosensor coupled with a microfilter system for label-free and highly sensitive detection of BNP in whole blood. The PtNPs-decorated rGO FET sensor was obtained by drop-casting rGO onto the pre-fabricated FET chip and subsequently assembling PtNPs on the graphene surface. After anti-BNP was bound to the PtNPs surface, BNP was successfully detected by the anti-BNP immobilized FET biosensor. It was found that the developed FET biosensor was able to achieve a low detection limitation of 100fM. Moreover, BNP was successfully detected in human whole blood sample treated by a custom-made microfilter, suggesting the sensor's capability of working in a complex sample matrix. The developed FET biosensor provides a new sensing platform for protein detection, showing its potential applications in clinic sample.

  6. Tuning the electrical properties of Si nanowire field-effect transistors by molecular engineering.

    Science.gov (United States)

    Bashouti, Muhammad Y; Tung, Raymond T; Haick, Hossam

    2009-12-01

    Exposed facets of n-type silicon nanowires (Si NWs) fabricated by a top-down approach are successfully terminated with different organic functionalities, including 1,3-dioxan-2-ethyl, butyl, allyl, and propyl-alcohol, using a two-step chlorination/alkylation method. X-ray photoemission spectroscopy and spectroscopic ellipsometry establish the bonding and the coverage of these molecular layers. Field-effect transistors fabricated from these Si NWs displayed characteristics that depended critically on the type of molecular termination. Without molecules the source-drain conduction is unable to be turned off by negative gate voltages as large as -20 V. Upon adsorption of organic molecules there is an observed increase in the "on" current at large positive gate voltages and also a reduction, by several orders of magnitude, of the "off" current at large negative gate voltages. The zero-gate voltage transconductance of molecule-terminated Si NW correlates with the type of organic molecule. Adsorption of butyl and 1,3-dioxan-2-ethyl molecules improves the channel conductance over that of the original SiO(2)-Si NW, while adsorption of molecules with propyl-alcohol leads to a reduction. It is shown that a simple assumption based on the possible creation of surface states alongside the attachment of molecules may lead to a qualitative explanation of these electrical characteristics. The possibility and potential implications of modifying semiconductor devices by tuning the distribution of surface states via the functionality of attached molecules are discussed.

  7. Dynamic Wavelength-Tunable Photodetector Using Subwavelength Graphene Field-Effect Transistors

    Science.gov (United States)

    Léonard, François; Spataru, Catalin D.; Goldflam, Michael; Peters, David W.; Beechem, Thomas E.

    2017-01-01

    Dynamic wavelength tunability has long been the holy grail of photodetector technology. Because of its atomic thickness and unique properties, graphene opens up new paradigms to realize this concept, but so far this has been elusive experimentally. Here we employ detailed quantum transport modeling of photocurrent in graphene field-effect transistors (including realistic electromagnetic fields) to show that wavelength tunability is possible by dynamically changing the gate voltage. We reveal the phenomena that govern the behavior of this type of device and show significant departure from the simple expectations based on vertical transitions. We find strong focusing of the electromagnetic fields at the contact edges over the same length scale as the band-bending. Both of these spatially-varying potentials lead to an enhancement of non-vertical optical transitions, which dominate even in the absence of phonon or impurity scattering. We also show that the vanishing density of states near the Dirac point leads to contact blocking and a gate-dependent modulation of the photocurrent. Several of the effects discussed here should be applicable to a broad range of one- and two-dimensional materials and devices. PMID:28374842

  8. High performance ring oscillators from 10-nm wide silicon nanowire field-effect transistors

    KAUST Repository

    Huang, Ruo-Gu

    2011-06-24

    We explore 10-nm wide Si nanowire (SiNW) field-effect transistors (FETs) for logic applications, via the fabrication and testing of SiNW-based ring oscillators. We report on SiNW surface treatments and dielectric annealing, for producing SiNW FETs that exhibit high performance in terms of large on/off-state current ratio (~108), low drain-induced barrier lowering (~30 mV) and low subthreshold swing (~80 mV/decade). The performance of inverter and ring-oscillator circuits fabricated from these nanowire FETs are also explored. The inverter demonstrates the highest voltage gain (~148) reported for a SiNW-based NOT gate, and the ring oscillator exhibits near rail-to-rail oscillation centered at 13.4 MHz. The static and dynamic characteristics of these NW devices indicate that these SiNW-based FET circuits are excellent candidates for various high-performance nanoelectronic applications. © 2011 Tsinghua University Press and Springer-Verlag Berlin Heidelberg.

  9. Core-shell homojunction silicon vertical nanowire tunneling field-effect transistors

    Science.gov (United States)

    Yoon, Jun-Sik; Kim, Kihyun; Baek, Chang-Ki

    2017-01-01

    We propose three-terminal core-shell (CS) silicon vertical nanowire tunneling field-effect transistors (TFETs), which can be fabricated by conventional CMOS technology. CS TFETs show lower subthreshold swing (SS) and higher on-state current than conventional TFETs through their high surface-to-volume ratio, which increases carrier-tunneling region with no additional device area. The on-state current can be enhanced by increasing the nanowire height, decreasing equivalent oxide thickness (EOT) or creating a nanowire array. The off-state current is also manageable for power saving through selective epitaxial growth at the top-side nanowire region. CS TFETs with an EOT of 0.8 nm and an aspect ratio of 20 for the core nanowire region provide the largest drain current ranges with point SS values below 60 mV/dec and superior on/off current ratio under all operation voltages of 0.5, 0.7, and 1.0 V. These devices are promising for low-power applications at low fabrication cost and high device density.

  10. Development of high-performance printed organic field-effect transistors and integrated circuits.

    Science.gov (United States)

    Xu, Yong; Liu, Chuan; Khim, Dongyoon; Noh, Yong-Young

    2015-10-28

    Organic electronics is regarded as an important branch of future microelectronics especially suited for large-area, flexible, transparent, and green devices, with their low cost being a key benefit. Organic field-effect transistors (OFETs), the primary building blocks of numerous expected applications, have been intensively studied, and considerable progress has recently been made. However, there are still a number of challenges to the realization of high-performance OFETs and integrated circuits (ICs) using printing technologies. Therefore, in this perspective article, we investigate the main issues concerning developing high-performance printed OFETs and ICs and seek strategies for further improvement. Unlike many other studies in the literature that deal with organic semiconductors (OSCs), printing technology, and device physics, our study commences with a detailed examination of OFET performance parameters (e.g., carrier mobility, threshold voltage, and contact resistance) by which the related challenges and potential solutions to performance development are inspected. While keeping this complete understanding of device performance in mind, we check the printed OFETs' components one by one and explore the possibility of performance improvement regarding device physics, material engineering, processing procedure, and printing technology. Finally, we analyze the performance of various organic ICs and discuss ways to optimize OFET characteristics and thus develop high-performance printed ICs for broad practical applications.

  11. Vacuum ultraviolet radiation effects on two-dimensional MoS2 field-effect transistors

    Science.gov (United States)

    McMorrow, Julian J.; Cress, Cory D.; Arnold, Heather N.; Sangwan, Vinod K.; Jariwala, Deep; Schmucker, Scott W.; Marks, Tobin J.; Hersam, Mark C.

    2017-02-01

    Atomically thin MoS2 has generated intense interest for emerging electronics applications. Its two-dimensional nature and potential for low-power electronics are particularly appealing for space-bound electronics, motivating the need for a fundamental understanding of MoS2 electronic device response to the space radiation environment. In this letter, we quantify the response of MoS2 field-effect transistors (FETs) to vacuum ultraviolet (VUV) total ionizing dose radiation. Single-layer (SL) and multilayer (ML) MoS2 FETs are compared to identify differences that arise from thickness and band structure variations. The measured evolution of the FET transport properties is leveraged to identify the nature of VUV-induced trapped charge, isolating the effects of the interface and bulk oxide dielectric. In both the SL and ML cases, oxide trapped holes compete with interface trapped electrons, exhibiting an overall shift toward negative gate bias. Raman spectroscopy shows no variation in the MoS2 signatures as a result of VUV exposure, eliminating significant crystalline damage or oxidation as possible radiation degradation mechanisms. Overall, this work presents avenues for achieving radiation-hard MoS2 devices through dielectric engineering that reduces oxide and interface trapped charge.

  12. Nitrogen plasma-treated multilayer graphene-based field effect transistor fabrication and electronic characteristics

    Science.gov (United States)

    Su, Wei-Jhih; Chang, Hsuan-Chen; Honda, Shin-ichi; Lin, Pao-Hung; Huang, Ying-Sheng; Lee, Kuei-Yi

    2017-08-01

    Chemical doping with hetero-atoms is an effective method used to change the characteristics of materials. Nitrogen doping technology plays a critical role in regulating the electronic properties of graphene. Nitrogen plasma treatment was used in this work to dope nitrogen atoms to modulate multilayer graphene electrical properties. The measured I-V multilayer graphene-base field-effect transistor characteristics (GFETs) showed a V-shaped transfer curve with the hole and electron region separated from the measured current-voltage (I-V) minimum. GFETs fabricated with multilayer graphene from chemical vapor deposition (CVD) exhibited p-type behavior because of oxygen adsorption. After using different nitrogen plasma treatment times, the minimum in I-V characteristic shifted into the negative gate voltage region with increased nitrogen concentration and the GFET channel became an n-type semiconductor. GFETs could be easily fabricated using this method with potential for various applications. The GFET transfer characteristics could be tuned precisely by adjusting the nitrogen plasma treatment time.

  13. Ferroelectric Single-Crystal Gated Graphene/Hexagonal-BN/Ferroelectric Field-Effect Transistor.

    Science.gov (United States)

    Park, Nahee; Kang, Haeyong; Park, Jeongmin; Lee, Yourack; Yun, Yoojoo; Lee, Jeong-Ho; Lee, Sang-Goo; Lee, Young Hee; Suh, Dongseok

    2015-11-24

    The effect of a ferroelectric polarization field on the charge transport in a two-dimensional (2D) material was examined using a graphene monolayer on a hexagonal boron nitride (hBN) field-effect transistor (FET) fabricated using a ferroelectric single-crystal substrate, (1-x)[Pb(Mg1/3Nb2/3)O3]-x[PbTiO3] (PMN-PT). In this configuration, the intrinsic properties of graphene were preserved with the use of an hBN flake, and the influence of the polarization field from PMN-PT could be distinguished. During a wide-range gate-voltage (VG) sweep, a sharp inversion of the spontaneous polarization affected the graphene channel conductance asymmetrically as well as an antihysteretic behavior. Additionally, a transition from antihysteresis to normal ferroelectric hysteresis occurred, depending on the V(G) sweep range relative to the ferroelectric coercive field. We developed a model to interpret the complex coupling among antihysteresis, current saturation, and sudden conductance variation in relation with the ferroelectric switching and the polarization-assisted charge trapping, which can be generalized to explain the combination of 2D structured materials with ferroelectrics.

  14. Characteristics of Interlayer Tunneling Field-Effect Transistors Computed by a "DFT-Bardeen" Method

    Science.gov (United States)

    Li, Jun; Nie, Yifan; Cho, Kyeongjae; Feenstra, Randall M.

    2017-02-01

    Theoretical predictions have been made for the current-voltage characteristics of two-dimensional heterojunction interlayer tunneling field-effect transistors (Thin-TFETs), focusing on the magnitude of the current achievable in such devices. A theory based on the Bardeen tunneling method is employed, using wavefunctions obtained from first-principles density functional theory. This method permits convenient incorporation of differing materials into the source and drain electrodes, i.e., with different crystal structure, lattice constants, and/or band structure. Large variations in tunneling current are found, depending on the two-dimensional materials used for the source and drain electrodes. Tunneling between states derived from the center (Γ-point) of the Brillouin zone (BZ) is found, in general, to lead to larger current than for zone-edge (e.g., K-point) states. The differences, as large as an order of magnitude, between the present results and various prior predictions are discussed. Predicted values for the tunneling current, including the subthreshold swing, are compared with benchmark values for low-power digital applications. Contact resistance is considered, and its effect on the tunneling current demonstrated.

  15. Analysis of the subthreshold characteristics of vertical tunneling field effect transistors

    Institute of Scientific and Technical Information of China (English)

    Han Zhongfang; Ru Guoping; Ruan Gang

    2013-01-01

    Subthreshold characteristics of vertical tunneling field effect transistors (VTFETs) with an n+-pocket in the p+-source are studied by simulating the transfer characteristics with a commercial device simulator.Three types of subthreshold characteristics are demonstrated for the device with different pocket thicknesses and doping concentrations.Band diagram analysis shows that such a VTFET can be treated as a gate-controlled tunnel diode connected in series with a conventional n-channel metal-oxide-semiconductor FET.This VTFET can work either as a TFET or an n-MOSFET in the subthreshold region,depending on the turn-on sequence of these two components.To our knowledge,this is the first time such a device model has been used to explain the subthreshold characteristics of this kind of VTFET and the simulation results demonstrate that such a device model is convictive and valid.Our results indicate that the design of the n+ pocket is crucial for such a VTFET in order to achieve ultra-steep turn-on characteristics.

  16. Hybrid porphyrin-silicon nanowire field-effect transistor by opto-electrical excitation.

    Science.gov (United States)

    Seol, Myeong-Lok; Choi, Sung-Jin; Choi, Ji-Min; Ahn, Jae-Hyuk; Choi, Yang-Kyu

    2012-09-25

    A porphyrin-silicon nanowire (Si-NW) hybrid field-effect transistor is introduced. The hybrid device has separate electrical and optical gates surrounding the Si-NW channel. Porphyrin, a component of chlorophyll, is employed as an optical gate to modulate the potential of the Si-NW channel. Due to the independently formed hybrid gates, both optical and electrical excitation can effectively modulate the device. The exposed porphyrin optical gate responds to the optical excitation, and independently formed electrical gates respond to the electrical excitation. Charge transfer characteristics between a semiconductor channel and the porphyrin optical gate are deeply investigated. Optical, electrical, and opto-electrical excitation methods are employed to analyze the charging and discharging behaviors. Of these methods, opto-electrical excitation enables the strongest charge transfer because the inversion electron formation by an electrical pulse and the photoinduced charge transfer by an optical stimulus are affected simultaneously. Discharging processes, such as rapid discharging, exponential detrapping, and the formation of metastable states are also analyzed.

  17. Improved synthesis and growth of graphene oxide for field effect transistor biosensors.

    Science.gov (United States)

    Huang, Jingfeng; Chen, Hu; Jing, Lin; Fam, Derrick; Tok, Alfred Iing Yoong

    2016-08-01

    Reduced graphene oxide (RGO) has many advantages over graphene such as low-cost, aqueous processable and industrial-scalable. However, two main limitations that prevent the use of RGO in electronics are the high electrical resistance and large electrical resistance deviation between fabricated devices. This limits RGO's use in biosensors, capacitors and other electronic devices. Herein, we present (1) a modified Hummer's method to obtain large RGO flakes via in-situ size fractionation and (2) the novel growth of RGO which can bridge the gaps in-between existing RGO flakes. Together, these two processes reduced the electrical resistance drastically from 1.99E + 06 to 4.68E + 03 Ω/square and the standard deviation decreased from 80.5 % to 16.5 %. The RGO was then fabricated into a field-effect transistor biosensor. A 1 pmol to 100 nmol change in Cytochrome C protein corresponded to a 3 % change in electrical resistance. The reported improved RGO synthesis method and subsequent growth enable large-scale application of RGO in practical electronic devices such as biosensors.

  18. Double gate graphene nanoribbon field effect transistor with single halo pocket in channel region

    Science.gov (United States)

    Naderi, Ali

    2016-01-01

    A new structure for graphene nanoribbon field-effect transistors (GNRFETs) is proposed and investigated using quantum simulation with a nonequilibrium Green's function (NEGF) method. Tunneling leakage current and ambipolar conduction are known effects for MOSFET-like GNRFETs. To minimize these issues a novel structure with a simple change of the GNRFETs by using single halo pocket in the intrinsic channel region, "Single Halo GNRFET (SH-GNRFET)", is proposed. An appropriate halo pocket at source side of channel is used to modify potential distribution of the gate region and weaken band to band tunneling (BTBT). In devices with materials like Si in channel region, doping type of halo and source/drain regions are different. But, here, due to the smaller bandgap of graphene, the mentioned doping types should be the same to reduce BTBT. Simulations have shown that in comparison with conventional GNRFET (C-GNRFET), an SH-GNRFET with appropriately halo doping results in a larger ON current (Ion), smaller OFF current (Ioff), a larger ON-OFF current ratio (Ion/Ioff), superior ambipolar characteristics, a reduced power-delay product and lower delay time.

  19. A CMOS-MEMS arrayed resonant-gate field effect transistor (RGFET) oscillator

    Science.gov (United States)

    Chin, Chi-Hang; Li, Ming-Huang; Chen, Chao-Yu; Wang, Yu-Lin; Li, Sheng-Shian

    2015-11-01

    A high-frequency CMOS-MEMS arrayed resonant-gate field effect transistor (RGFET) fabricated by a standard 0.35 μm 2-poly-4-metal CMOS-MEMS platform is implemented to enable a Pierce-type oscillator. The proposed arrayed RGFET exhibits low motional impedance of only 5 kΩ under a purely capacitive transduction and decent power handling capability. With such features, the implemented oscillator shows impressive phase noise of  -117 dBc Hz-1 at the far-from-carrier offset (1 MHz). In this work, we design a clamped-clamped beam (CCB) arrayed resonator utilizing a high-velocity mechanical coupling scheme to serve as the resonant-gate array. To achieve a functional arrayed RGFET, a corresponding FET array is directly placed underneath the resonant gate array to convert the motional current on the resonant-gate array into a voltage output with a tunable transconductance gain. To understand the behavior of the proposed device, an equivalent circuit model consisting of the resonant unit and FET is also provided. To verify the effects of the post-CMOS process on device performance, a conventional MOS I D current measurement is carried out. Finally, a CMOS-MEMS arrayed RGFET oscillator is realized by utilizing a Pierce oscillator architecture, showing decent phase noise performance that benefits from the array design to alleviate the nonlinear effect of the resonant gate.

  20. Carbon nanotube field effect transistors for the fast and selective detection of human immunoglobulin G.

    Science.gov (United States)

    Cid, Cristina C; Riu, Jordi; Maroto, Alicia; Rius, F Xavier

    2008-08-01

    We report a field effect transistor (FET) based on a network of single-walled carbon nanotubes (SWCNTs) which can selectively detect human immunoglobulin G (HIgG). HIgG antibodies, which are strongly adsorbed onto the walls of the SWCNTs, are the basic elements of the recognition layer. The non-specific binding of proteins and the effects of other interferences are avoided by covering the non-adsorbed areas of the SWCNTs with Tween 20. The selectivity of the sensor has been tested against bovine serum albumin (BSA), the most abundant protein in plasma. HIgG in aqueous solution with concentrations from 1.25 mg L(-1) (8 nM) can be readily detected with response times of about 10 min. The SWCNT networks that form the basis of the sensor are easily grown by chemical vapour deposition. Silver screen-printed electrodes make the sensor quick to build. The sensitivity obtained with this sensor is similar to other FET devices based on SWCNTs built using much more complicated lithography processes. Moreover, the sensor is a reagentless device that does not need labels to detect HIgG.

  1. Rapid detection of Aspergillus flavus in rice using biofunctionalized carbon nanotube field effect transistors.

    Science.gov (United States)

    Villamizar, Raquel A; Maroto, Alicia; Rius, F Xavier

    2011-01-01

    In the present study, we have used carbon nanotube field effect transistors (FET) that have been functionalized with protein G and IgG to detect Aspergillus flavus in contaminated milled rice. The adsorbed protein G on the carbon nanotubes walls enables the IgG anti-Aspergillus antibodies to be well oriented and therefore to display full antigen binding capacity for fungal antigens. A solution of Tween 20 and gelatine was used as an effective blocking agent to prevent the non-specific binding of the antibodies and other moulds and also to protect the transducer against the interferences present in the rice samples. Our FET devices were able to detect at least 10 μg/g of A. flavus in only 30 min. To evaluate the selectivity of our biosensors, Fusarium oxysporum and Penicillium chrysogenum were tested as potential competing moulds for A. flavus. We have proved that our devices are highly selective tools for detecting mycotoxigenic moulds at low concentrations in real samples.

  2. Percolative switching in transition metal dichalcogenide field-effect transistors at room temperature

    Science.gov (United States)

    Paul, Tathagata; Ghatak, Subhamoy; Ghosh, Arindam

    2016-03-01

    We have addressed the microscopic transport mechanism at the switching or ‘on-off’ transition in transition metal dichalcogenide (TMDC) field-effect transistors (FETs), which has been a controversial topic in TMDC electronics, especially at room temperature. With simultaneous measurement of channel conductivity and its slow time-dependent fluctuation (or noise) in ultrathin WSe2 and MoS2 FETs on insulating SiO2 substrates where noise arises from McWhorter-type carrier number fluctuations, we establish that the switching in conventional backgated TMDC FETs is a classical percolation transition in a medium of inhomogeneous carrier density distribution. From the experimentally observed exponents in the scaling of noise magnitude with conductivity, we observe unambiguous signatures of percolation in a random resistor network, particularly, in WSe2 FETs close to switching, which crosses over to continuum percolation at a higher doping level. We demonstrate a powerful experimental probe to the microscopic nature of near-threshold electrical transport in TMDC FETs, irrespective of the material detail, device geometry, or carrier mobility, which can be extended to other classes of 2D material-based devices as well.

  3. Biologically templated assembly of hybrid semiconducting nanomesh for high performance field effect transistors and sensors

    Science.gov (United States)

    Byeon, Hye-Hyeon; Lee, Seung-Woo; Lee, Eun-Hee; Kim, Woong; Yi, Hyunjung

    2016-10-01

    Delicately assembled composites of semiconducting nanomaterials and biological materials provide an attractive interface for emerging applications, such as chemical/biological sensors, wearable health monitoring devices, and therapeutic agent releasing devices. The nanostructure of composites as a channel and a sensing material plays a critical role in the performance of field effect transistors (FETs). Therefore, it is highly desirable to prepare elaborate composite that can allow the fabrication of high performance FETs and also provide high sensitivity and selectivity in detecting specific chemical/biological targets. In this work, we demonstrate that high performance FETs can be fabricated with a hydrodynamically assembled composite, a semiconducting nanomesh, of semiconducting single-walled carbon nanotubes (S-SWNTs) and a genetically engineered M13 phage to show strong binding affinity toward SWNTs. The semiconducting nanomesh enables a high on/off ratio (~104) of FETs. We also show that the threshold voltage and the channel current of the nanomesh FETs are sensitive to the change of the M13 phage surface charge. This biological gate effect of the phage enables the detection of biologically important molecules such as dopamine and bisphenol A using nanomesh-based FETs. Our results provide a new insight for the preparation of composite material platform for highly controllable bio/electronics interfaces.

  4. High-performance integrated field-effect transistor-based sensors

    Energy Technology Data Exchange (ETDEWEB)

    Adzhri, R., E-mail: adzhri@gmail.com [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Md Arshad, M.K., E-mail: mohd.khairuddin@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); School of Microelectronic Engineering (SoME), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Gopinath, Subash C.B., E-mail: subash@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); School of Bioprocess Engineering (SBE), Universiti Malaysia Perlis (UniMAP), Arau, Perlis (Malaysia); Ruslinda, A.R., E-mail: ruslinda@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Fathil, M.F.M., E-mail: faris.fathil@gmail.com [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Ayub, R.M., E-mail: ramzan@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Nor, M. Nuzaihan Mohd, E-mail: m.nuzaihan@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia); Voon, C.H., E-mail: chvoon@unimap.edu.my [Institute of Nano Electronic Engineering (INEE), Universiti Malaysia Perlis (UniMAP), Kangar, Perlis (Malaysia)

    2016-04-21

    Field-effect transistors (FETs) have succeeded in modern electronics in an era of computers and hand-held applications. Currently, considerable attention has been paid to direct electrical measurements, which work by monitoring changes in intrinsic electrical properties. Further, FET-based sensing systems drastically reduce cost, are compatible with CMOS technology, and ease down-stream applications. Current technologies for sensing applications rely on time-consuming strategies and processes and can only be performed under recommended conditions. To overcome these obstacles, an overview is presented here in which we specifically focus on high-performance FET-based sensor integration with nano-sized materials, which requires understanding the interaction of surface materials with the surrounding environment. Therefore, we present strategies, material depositions, device structures and other characteristics involved in FET-based devices. Special attention was given to silicon and polyaniline nanowires and graphene, which have attracted much interest due to their remarkable properties in sensing applications. - Highlights: • Performance of FET-based biosensors for the detection of biomolecules is presented. • Silicon nanowire, polyaniline and graphene are the highlighted nanoscaled materials as sensing transducers. • The importance of surface material interaction with the surrounding environment is discussed. • Different device structure architectures for ease in fabrication and high sensitivity of sensing are presented.

  5. Screening-induced surface polar optical phonon scattering in dual-gated graphene field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Bo, E-mail: hubo2011@semi.ac.cn

    2015-03-15

    The effect of surface polar optical phonons (SOs) from the dielectric layers on electron mobility in dual-gated graphene field effect transistors (GFETs) is studied theoretically. By taking into account SO scattering of electron as a main scattering mechanism, the electron mobility is calculated by the iterative solution of Boltzmann transport equation. In treating scattering with the SO modes, the dynamic dielectric screening is included and compared to the static dielectric screening and the dielectric screening in the static limit. It is found that the dynamic dielectric screening effect plays an important role in the range of low net carrier density. More importantly, in-plane acoustic phonon scattering and charged impurity scattering are also included in the total mobility for SiO{sub 2}-supported GFETs with various high-κ top-gate dielectric layers considered. The calculated total mobility results suggest both Al{sub 2}O{sub 3} and AlN are the promising candidate dielectric layers for the enhancement in room temperature mobility of graphene in the future.

  6. Biologically templated assembly of hybrid semiconducting nanomesh for high performance field effect transistors and sensors

    Science.gov (United States)

    Byeon, Hye-Hyeon; Lee, Seung-Woo; Lee, Eun-Hee; Kim, Woong; Yi, Hyunjung

    2016-01-01

    Delicately assembled composites of semiconducting nanomaterials and biological materials provide an attractive interface for emerging applications, such as chemical/biological sensors, wearable health monitoring devices, and therapeutic agent releasing devices. The nanostructure of composites as a channel and a sensing material plays a critical role in the performance of field effect transistors (FETs). Therefore, it is highly desirable to prepare elaborate composite that can allow the fabrication of high performance FETs and also provide high sensitivity and selectivity in detecting specific chemical/biological targets. In this work, we demonstrate that high performance FETs can be fabricated with a hydrodynamically assembled composite, a semiconducting nanomesh, of semiconducting single-walled carbon nanotubes (S-SWNTs) and a genetically engineered M13 phage to show strong binding affinity toward SWNTs. The semiconducting nanomesh enables a high on/off ratio (~104) of FETs. We also show that the threshold voltage and the channel current of the nanomesh FETs are sensitive to the change of the M13 phage surface charge. This biological gate effect of the phage enables the detection of biologically important molecules such as dopamine and bisphenol A using nanomesh-based FETs. Our results provide a new insight for the preparation of composite material platform for highly controllable bio/electronics interfaces. PMID:27762315

  7. Inexpensive and fast pathogenic bacteria screening using field-effect transistors.

    Science.gov (United States)

    Formisano, Nello; Bhalla, Nikhil; Heeran, Mel; Reyes Martinez, Juana; Sarkar, Amrita; Laabei, Maisem; Jolly, Pawan; Bowen, Chris R; Taylor, John T; Flitsch, Sabine; Estrela, Pedro

    2016-11-15

    While pathogenic bacteria contribute to a large number of globally important diseases and infections, current clinical diagnosis is based on processes that often involve culturing which can be time-consuming. Therefore, innovative, simple, rapid and low-cost solutions to effectively reduce the burden of bacterial infections are urgently needed. Here we demonstrate a label-free sensor for fast bacterial detection based on metal-oxide-semiconductor field-effect transistors (MOSFETs). The electric charge of bacteria binding to the glycosylated gates of a MOSFET enables quantification in a straightforward manner. We show that the limit of quantitation is 1.9×10(5) CFU/mL with this simple device, which is more than 10,000-times lower than is achieved with electrochemical impedance spectroscopy (EIS) and matrix-assisted laser desorption ionisation time-of-flight mass spectrometry (MALDI-ToF) on the same modified surfaces. Moreover, the measurements are extremely fast and the sensor can be mass produced at trivial cost as a tool for initial screening of pathogens.

  8. Modeling comparison of graphene nanoribbon field effect transistors with single vacancy defect

    Science.gov (United States)

    Nazari, Atefeh; Faez, Rahim; Shamloo, Hassan

    2016-09-01

    In this paper, some important circuit parameters of a monolayer armchair graphene nanoribbon (GNR) field effect transistor (GNRFET) in different structures are studied. Also, these structures are Ideal with no defect, 1SVGNRFET with one single vacancy defect, and 3SVsGNRFET with three SV defects. Moreover, the circuit parameters are extracted based on Semi Classical Top of Barrier Modeling (SCTOBM) method. The I-V characteristics simulations of Ideal GNRFET, 1SVGNRFET and 3SVsGNRFET are used for comparing with SCTOBM method. These simulations are solved with Poisson-Schrodinger equation self-consistently by using Non- Equilibrium Green Function (NEGF) and in the real space approach. The energy band structure of nanoribbon is obtained by using nearest-neighbour interactions within an approximation tight-binding method. The modeling results show that 3SVsGNRFET in comparison to 1SVGNRFET has higher transconductance, cut-off frequency, electron average velocity, mobile charge, and quantum capacitance. Also, 3SVsGNRFET has smaller gate, drain and source capacitances than Ideal GNRFET. Furthermore, Drain-induced barrier lowering (DIBL) and sub-threshold swing (SS) of 3SVsGNRFET are smaller than 1SVGNRFET.

  9. Development of molecularly imprinted polymer-based field effect transistor for sugar chain sensing

    Science.gov (United States)

    Nishitani, Shoichi; Kajisa, Taira; Sakata, Toshiya

    2017-04-01

    In this study, we developed a molecularly imprinted polymer-based field-effect transistor (MIP-gate FET) for selectively detecting sugar chains in aqueous media, focusing on 3‧-sialyllactose (3SLac) and 6‧-sialyllactose (6SLac). The FET biosensor enables the detection of small molecules as long as they have intrinsic charges. Additionally, the MIP gels include the template for the target molecule, which is selectively trapped without requiring enzyme-target molecule reaction. The MIP gels were synthesized on the gate surface of the FET device, including phenylboronic acid (PBA), which enables binding to sugar chains. Firstly, the 3SLac-MIP-gate FET quantitatively detected 3SLac at µM levels. This is because the FET device recognized the change in molecular charges on the basis of PBA-3SLac binding in the MIP gel. Moreover, 3SLac was selectively detected using the 3SLac- and 6SLac-MIP-gate FETs to some extent, where the detecting signal from the competent was suppressed by 40% at maximum. Therefore, a platform based on the MIP-coupled FET biosensor is suitable for a selective biosensing system in an enzyme-free manner, which can be applied widely in medical fields. However, we need to further improve the selectivity of MIP-gate FETs to discriminate more clearly between similar structures of sugar chains such as 3SLac and 6SLac.

  10. Poly (ethylene imine)-modulated transport behaviors of graphene field effect transistors with double Dirac points

    Science.gov (United States)

    Sun, Yilin; Xie, Dan; Zhang, Cheng; Li, Xinming; Xu, Jianlong; Sun, Mengxing; Teng, Changjiu; Li, Xian; Zhu, Hongwei

    2017-04-01

    The bottom-gated graphene field-effect transistors (GFETs) with HfO2 as the dielectric layer are fabricated and the transport behaviors with double Dirac points defined as the right conductance minima (VDirac+) and the left one (VDirac-) are obtained, which exhibit the unique W-shaped transform characteristics rather than the typical V-shape. This observation indicates that the graphene in the channel region shows the different doping behaviors from that underlying the metal contact region. The W-shaped characteristics of GFETs are affected by the ambient environment and the time-dependence of double Dirac points has been also found. After being treated by Poly (ethylene imine) (PEI), the transport behaviors of GFETs could be modulated, especially for VDirac+ showing more obvious negative shift, indicating that PEI has a remarkable n-doping effect on the graphene in the channel region. PEI also screens the environmental influence and could protect the graphene from being p-doped to some extent. At the same time, the annealing effect has been also studied and it is found that the proper annealing process could contribute to the recovery of the graphene properties.

  11. Improved double-gate armchair silicene nanoribbon field-effect-transistor at large transport bandgap

    Science.gov (United States)

    Mohsen, Mahmoudi; Zahra, Ahangari; Morteza, Fathipour

    2016-01-01

    The electrical characteristics of a double-gate armchair silicene nanoribbon field-effect-transistor (DG ASiNR FET) are thoroughly investigated by using a ballistic quantum transport model based on non-equilibrium Green’s function (NEGF) approach self-consistently coupled with a three-dimensional (3D) Poisson equation. We evaluate the influence of variation in uniaxial tensile strain, ribbon temperature and oxide thickness on the on-off current ratio, subthreshold swing, transconductance and the delay time of a 12-nm-length ultranarrow ASiNR FET. A novel two-parameter strain magnitude and temperature-dependent model is presented for designing an optimized device possessing balanced amelioration of all the electrical parameters. We demonstrate that employing HfO2 as the gate insulator can be a favorable choice and simultaneous use of it with proper combination of temperature and strain magnitude can achieve better device performance. Furthermore, a general model power (GMP) is derived which explicitly provides the electron effective mass as a function of the bandgap of a hydrogen passivated ASiNR under strain.

  12. Reporter-encapsulated liposomes on graphene field effect transistors for signal enhanced detection of physiological enzymes.

    Science.gov (United States)

    Chen, Hu; Lim, Seng Koon; Chen, Peng; Huang, Jingfeng; Wang, Yi; Palaniappan, Alagappan; Platt, Mark; Liedberg, Bo; Tok, Alfred Iing Yoong

    2015-02-01

    A novel approach for enzymatic assay using reporter-encapsulated liposomes on graphene field effect transistors (FET) is proposed. This approach involves real time monitoring of drain current (Id) of reduced graphene oxide (rGO) upon rupture of reporter-encapsulated 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) liposomes triggered by enzymes. For validation of the proposed approach, 2,4,6-trinitrophenol (TNP) is used as the reporter for specific detection of phospholipase A2 (PLA2), a key enzyme in various membrane related physiological processes. Experimental results revealed that Id increased with PLA2 concentration, which is attributed to the interaction between released TNP and rGO. The limit of detection (LOD) achieved by the proposed approach was 80 pM, which is superior to most assays reported previously and much lower than the cut-off level of circulating secretory PLA2 (2.07 nM). Besides the high accuracy of the electronic detection methodology, the signal enhancement effect realized by the excess concentration of TNP (approximately 1 mM) in liposomes is believed to be the main reason for the significantly enhanced sensitivity of the proposed assay, indicating great potential for further improvement in the sensitivity by increasing the concentration of TNP. In addition, the proposed approach is rapid (incubation time ≤ 10 min) and label-free, thus showing great potential for practical applications in the future.

  13. Schottky barrier and contact resistance of InSb nanowire field-effect transistors

    Science.gov (United States)

    Fan, Dingxun; Kang, N.; Gorji Ghalamestani, Sepideh; Dick, Kimberly A.; Xu, H. Q.

    2016-07-01

    Understanding of the electrical contact properties of semiconductor nanowire (NW) field-effect transistors (FETs) plays a crucial role in the use of semiconducting NWs as building blocks for future nanoelectronic devices and in the study of fundamental physics problems. Here, we report on a study of the contact properties of Ti/Au, a widely used contact metal combination, when contacting individual InSb NWs via both two-probe and four-probe transport measurements. We show that a Schottky barrier of height {{{Φ }}}{{SB}}˜ 20 {{meV}} is present at the metal-InSb NW interfaces and its effective height is gate-tunable. The contact resistance ({R}{{c}}) in the InSb NWFETs is also analyzed by magnetotransport measurements at low temperatures. It is found that {R}{{c}} in the on-state exhibits a pronounced magnetic field-dependent feature, namely it is increased strongly with increasing magnetic field after an onset field {B}{{c}}. A qualitative picture that takes into account magnetic depopulation of subbands in the NWs is provided to explain the observation. Our results provide solid experimental evidence for the presence of a Schottky barrier at Ti/Au-InSb NW interfaces and can be used as a basis for design and fabrication of novel InSb NW-based nanoelectronic devices and quantum devices.

  14. Quantum mechanical solver for confined heterostructure tunnel field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Verreck, Devin, E-mail: devin.verreck@imec.be; Groeseneken, Guido [imec, Kapeldreef 75, 3001 Leuven (Belgium); Department of Electrical Engineering, KU Leuven, 3001 Leuven (Belgium); Van de Put, Maarten; Sorée, Bart; Magnus, Wim [imec, Kapeldreef 75, 3001 Leuven (Belgium); Departement of Physics, Universiteit Antwerpen, 2020 Antwerpen (Belgium); Verhulst, Anne S.; Collaert, Nadine; Thean, Aaron [imec, Kapeldreef 75, 3001 Leuven (Belgium); Vandenberghe, William G. [Department of Materials Science and Engineering, University of Texas at Dallas, Richardson, Texas 75080 (United States)

    2014-02-07

    Heterostructure tunnel field-effect transistors (HTFET) are promising candidates for low-power applications in future technology nodes, as they are predicted to offer high on-currents, combined with a sub-60 mV/dec subthreshold swing. However, the effects of important quantum mechanical phenomena like size confinement at the heterojunction are not well understood, due to the theoretical and computational difficulties in modeling realistic heterostructures. We therefore present a ballistic quantum transport formalism, combining a novel envelope function approach for semiconductor heterostructures with the multiband quantum transmitting boundary method, which we extend to 2D potentials. We demonstrate an implementation of a 2-band version of the formalism and apply it to study confinement in realistic heterostructure diodes and p-n-i-n HTFETs. For the diodes, both transmission probabilities and current densities are found to decrease with stronger confinement. For the p-n-i-n HTFETs, the improved gate control is found to counteract the deterioration due to confinement.

  15. Physically responsive field-effect transistors with giant electromechanical coupling induced by nanocomposite gate dielectrics.

    Science.gov (United States)

    Tien, Nguyen Thanh; Trung, Tran Quang; Seoul, Young Gug; Kim, Do Il; Lee, Nae-Eung

    2011-09-27

    Physically responsive field-effect transistors (physi-FETs) that are sensitive to physical stimuli have been studied for decades. The important issue for separating the responses of sensing materials from interference by other subcomponents in a FET transducer under global physical stimuli has not been completely resolved. In addition, challenges remain with regard to the design and employment of smart materials for flexible physi-FETs with a large electro-physical coupling effect. In this article, we propose the direct integration of nanocomposite (NC) gate dielectrics of barium titanate (BT) nanoparticles (NPs) and highly crystalline poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) into flexible organic FETs to achieve a large electro-physical coupling effect. Additionally, a new alternating current biasing method is proposed for precise extraction and quantification of tiny variations in the remnant polarization of NCs caused by mechanical stimuli. An investigation of physi-FETs under static mechanical stimuli revealed the first ever reported giant, positive piezoelectric coefficients of d(33) up to 960 pC/N in the NCs. The large coefficients are presumably due to the significant contributions of the intrinsic positive piezoelectricity of the BT NPs and P(VDF-TrFE) crystallites. © 2011 American Chemical Society

  16. Enhanced sensing of nonpolar volatile organic compounds by silicon nanowire field effect transistors.

    Science.gov (United States)

    Paska, Yair; Stelzner, Thomas; Christiansen, Silke; Haick, Hossam

    2011-07-26

    Silicon nanowire field effect transistors (Si NW FETs) are emerging as powerful sensors for direct detection of biological and chemical species. However, the low sensitivity of the Si NW FET sensors toward nonpolar volatile organic compounds (VOCs) is problematic for many applications. In this study, we show that modifying Si NW FETs with a silane monolayer having a low fraction of Si-O-Si bonds between the adjacent molecules greatly enhances the sensitivity toward nonpolar VOCs. This can be explained in terms of an indirect sensor-VOC interaction, whereby the nonpolar VOC molecules induce conformational changes in the organic monolayer, affecting (i) the dielectric constant and/or effective dipole moment of the organic monolayer and/or (ii) the density of charged surface states at the SiO(2)/monolayer interface. In contrast, polar VOCs are sensed directly via VOC-induced changes in the Si NW charge carriers, most probably due to electrostatic interaction between the Si NW and polar VOCs. A semiempirical model for the VOC-induced conductivity changes in the Si NW FETs is presented and discussed.

  17. Direct-written polymer field-effect transistors operating at 20 MHz

    Science.gov (United States)

    Perinot, Andrea; Kshirsagar, Prakash; Malvindi, Maria Ada; Pompa, Pier Paolo; Fiammengo, Roberto; Caironi, Mario

    2016-12-01

    Printed polymer electronics has held for long the promise of revolutionizing technology by delivering distributed, flexible, lightweight and cost-effective applications for wearables, healthcare, diagnostic, automation and portable devices. While impressive progresses have been registered in terms of organic semiconductors mobility, field-effect transistors (FETs), the basic building block of any circuit, are still showing limited speed of operation, thus limiting their real applicability. So far, attempts with organic FETs to achieve the tens of MHz regime, a threshold for many applications comprising the driving of high resolution displays, have relied on the adoption of sophisticated lithographic techniques and/or complex architectures, undermining the whole concept. In this work we demonstrate polymer FETs which can operate up to 20 MHz and are fabricated by means only of scalable printing techniques and direct-writing methods with a completely mask-less procedure. This is achieved by combining a fs-laser process for the sintering of high resolution metal electrodes, thus easily achieving micron-scale channels with reduced parasitism down to 0.19 pF mm‑1, and a large area coating technique of a high mobility polymer semiconductor, according to a simple and scalable process flow.

  18. Valence band states in Si-based p-type delta-doped field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Orozco, J C; Vlaev, Stoyan J, E-mail: jcmover@correo.unam.m [Unidad Academica de Fisica, Universidad Autonoma de Zacatecas, Calzada Solidaridad esquina con Paseo la Bufa S/N, C.P. 98060, Zacatecas, Zac. (Mexico)

    2009-05-01

    We present tight-binding calculations of the hole level structure of delta-doped Field Effect Transistor in a Si matrix within the first neighbors sp{sup 3}s* semi-empirical tight-binding model including spin. We employ analytical expressions for Schottky barrier potential and the p-type delta-doped well based on a Thomas-Fermi approximation, we consider these potentials as external ones, so in the computations they are added to the diagonal terms of the tight-binding Hamiltonian, by this way we have the possibility to study the energy levels behavior as we vary the backbone parameters in the system: the two-dimensional impurity density (p{sub 2d}) of the p-type delta-doped well and the contact voltage (V{sub c}). The aim of this calculation is to demonstrate that the tight-binding approximation is suitable for device characterization that permits us to propose optimal values for the input parameters involved in the device design.

  19. High performance dendrimer functionalized single-walled carbon nanotubes field effect transistor biosensor for protein detection

    Science.gov (United States)

    Rajesh, Sharma, Vikash; Puri, Nitin K.; Mulchandani, Ashok; Kotnala, Ravinder K.

    2016-12-01

    We report a single-walled carbon nanotube (SWNT) field-effect transistor (FET) functionalized with Polyamidoamine (PAMAM) dendrimer with 128 carboxyl groups as anchors for site specific biomolecular immobilization of protein antibody for C-reactive protein (CRP) detection. The FET device was characterized by scanning electron microscopy and current-gate voltage (I-Vg) characteristic studies. A concentration-dependent decrease in the source-drain current was observed in the regime of clinical significance, with a detection limit of ˜85 pM and a high sensitivity of 20% change in current (ΔI/I) per decade CRP concentration, showing SWNT being locally gated by the binding of CRP to antibody (anti-CRP) on the FET device. The low value of the dissociation constant (Kd = 0.31 ± 0.13 μg ml-1) indicated a high affinity of the device towards CRP analyte arising due to high anti-CRP loading with a better probe orientation on the 3-dimensional PAMAM structure.

  20. Sensing Responses Based on Transfer Characteristics of InAs Nanowire Field-Effect Transistors.

    Science.gov (United States)

    Tseng, Alex C; Lynall, David; Savelyev, Igor; Blumin, Marina; Wang, Shiliang; Ruda, Harry E

    2017-07-16

    Nanowire-based field-effect transistors (FETs) have demonstrated considerable promise for a new generation of chemical and biological sensors. Indium arsenide (InAs), by virtue of its high electron mobility and intrinsic surface accumulation layer of electrons, holds properties beneficial for creating high performance sensors that can be used in applications such as point-of-care testing for patients diagnosed with chronic diseases. Here, we propose devices based on a parallel configuration of InAs nanowires and investigate sensor responses from measurements of conductance over time and FET characteristics. The devices were tested in controlled concentrations of vapour containing acetic acid, 2-butanone and methanol. After adsorption of analyte molecules, trends in the transient current and transfer curves are correlated with the nature of the surface interaction. Specifically, we observed proportionality between acetic acid concentration and relative conductance change, off current and surface charge density extracted from subthreshold behaviour. We suggest the origin of the sensing response to acetic acid as a two-part, reversible acid-base and redox reaction between acetic acid, InAs and its native oxide that forms slow, donor-like states at the nanowire surface. We further describe a simple model that is able to distinguish the occurrence of physical versus chemical adsorption by comparing the values of the extracted surface charge density. These studies demonstrate that InAs nanowires can produce a multitude of sensor responses for the purpose of developing next generation, multi-dimensional sensor applications.

  1. Impact of device engineering on analog/RF performances of tunnel field effect transistors

    Science.gov (United States)

    Vijayvargiya, V.; Reniwal, B. S.; Singh, P.; Vishvakarma, S. K.

    2017-06-01

    The tunnel field effect transistor (TFET) and its analog/RF performance is being aggressively studied at device architecture level for low power SoC design. Therefore, in this paper we have investigated the influence of the gate-drain underlap (UL) and different dielectric materials for the spacer and gate oxide on DG-TFET (double gate TFET) and its analog/RF performance for low power applications. Here, it is found that the drive current behavior in DG-TFET with a UL feature while implementing dielectric material for the spacer is different in comparison to that of DG-FET. Further, hetero gate dielectric-based DG-TFET (HGDG-TFET) is more resistive against drain-induced barrier lowering (DIBL) as compared to DG-TFET with high-k (HK) gate dielectric. Along with that, as compared to DG-FET, this paper also analyses the attributes of UL and dielectric material on analog/RF performance of DG-TFET in terms of transconductance (gm ), transconductance generation factor (TGF), capacitance, intrinsic resistance (Rdcr), cut-off frequency (F T), and maximum oscillation frequency (F max). The LK spacer-based HGDG-TFET with a gate-drain UL has the potential to improve the RF performance of device.

  2. Strain Gated Bilayer Molybdenum Disulfide Field Effect Transistor with Edge Contacts.

    Science.gov (United States)

    Chai, Yu; Su, Shanshan; Yan, Dong; Ozkan, Mihrimah; Lake, Roger; Ozkan, Cengiz S

    2017-02-10

    Silicon nitride stress capping layer is an industry proven technique for increasing electron mobility and drive currents in n-channel silicon MOSFETs. Herein, the strain induced by silicon nitride is firstly characterized through the changes in photoluminescence and Raman spectra of a bare bilayer MoS2 (Molybdenum disulfide). To make an analogy of the strain-gated silicon MOSFET, strain is exerted to a bilayer MoS2 field effect transistor (FET) through deposition of a silicon nitride stress liner that warps both the gate and the source-drain area. Helium plasma etched MoS2 layers for edge contacts. Current on/off ratio and other performance metrics are measured and compared as the FETs evolve from back-gated, to top-gated and finally, to strain-gated configurations. While the indirect band gap of bilayer MoS2 at 0% strain is 1.25 eV, the band gap decreases as the tensile strain increases on an average of ~100 meV per 1% tensile strain, and the decrease in band gap is mainly due to lowering the conduction band at K point. Comparing top- and strain-gated structures, we find a 58% increase in electron mobility and 46% increase in on-current magnitude, signalling a benign effect of tensile strain on the carrier transport properties of MoS2.

  3. Impact of edge states on device performance of phosphorene heterojunction tunneling field effect transistors.

    Science.gov (United States)

    Liu, Fei; Wang, Jian; Guo, Hong

    2016-10-27

    Black phosphorus (BP) tunneling field effect transistors (TFETs) using heterojunctions (Hes) are investigated by atomistic quantum transport simulations. It is observed that edge states have a great impact on the transport characteristics of BP He-TFETs, which results in the potential pinning effect and deterioration of gate control. However, the on-state current can be effectively enhanced by using hydrogen to saturate the edge dangling bonds in BP He-TFETs, by which means edge states are quenched. By extending layered BP with a smaller band gap to the channel region and modulating the BP thickness, the device performance of BP He-TFETs can be further optimized and can fulfil the requirements of the international technology road-map for semiconductors (ITRS) 2013 for low power applications. In 15 nm 3L-1L and 4L-1L BP He-TFETs along the armchair direction the on-state currents are over two times larger than the current required by ITRS 2013 and can reach above 10(3) μA μm(-1) with the fixed off-state current of 10 pA μm(-1). It is also found that the ambipolar effect can be effectively suppressed in BP He-TFETs.

  4. Mechanically robust 39 GHz cut-off frequency graphene field effect transistors on flexible substrates.

    Science.gov (United States)

    Wei, Wei; Pallecchi, Emiliano; Haque, Samiul; Borini, Stefano; Avramovic, Vanessa; Centeno, Alba; Amaia, Zurutuza; Happy, Henri

    2016-08-07

    Graphene has been regarded as a promising candidate channel material for flexible devices operating at radio-frequency (RF). In this work we fabricated and fully characterized double bottom-gate graphene field effect transistors on flexible polymer substrates for high frequency applications. We report a record high as-measured current gain cut-off frequency (ft) of 39 GHz. The corresponding maximum oscillation frequency (fmax) is 13.5 GHz. These state of the art high frequency performances are stable against bending, with a typical variation of around 10%, for a bending radius of up to 12 mm. To demonstrate the reliability of our devices, we performed a fatigue stress test for RF-GFETs which were dynamically bend tested 1000 times at 1 Hz. The devices are mechanically robust, and performances are stable with typical variations of 15%. Finally we investigate thermal dissipation, which is a critical parameter for flexible electronics. We show that at the optimum polarization the normalized power dissipated by the GFETs is about 0.35 mW μm(-2) and that the substrate temperature is around 200 degree centigrade. At a higher power, irreversible degradations of the performances are observed. Our study on state of the art flexible GFETs demonstrates mechanical robustness and stability upon heating, two important elements to assess the potential of GFETs for flexible electronics.

  5. Frequency, delay and velocity analysis for intrinsic channel region of carbon nanotube field effect transistors

    Directory of Open Access Journals (Sweden)

    P. Geetha

    2014-03-01

    Full Text Available Gate wrap around field effect transistor is preferred for its good channel control. To study the high frequency behaviour of the device, parameters like cut-off frequency, transit or delay time, velocity are calculated and plotted. Double-walled and array of channels are considered in this work for enhanced output and impedance matching of the device with the measuring equipment terminal respectively. The perfomance of double-walledcarbon nanotube is compared with single-walled carbon nanotube and found that the device with double-wall shows appreciable improvement in its characteristics. Analysis of these parameters are done with various values of source/drain length, gate length, tube diameters and channel densities. The maximum cut-off frequency is found to be 72.3 THz with corresponding velocity as 5x106 m/s for channel density as 3 and gate length as 11nm. The number of channel is varied from 3 to 21 and found that the perfromance of the device containing double-walled carbon nano tube is better for channel number lesser than or equal to 12. The proposed modelling can be used for designing devices to handle high speed applications of future generation.

  6. Core-shell homojunction silicon vertical nanowire tunneling field-effect transistors

    Science.gov (United States)

    Yoon, Jun-Sik; Kim, Kihyun; Baek, Chang-Ki

    2017-01-01

    We propose three-terminal core-shell (CS) silicon vertical nanowire tunneling field-effect transistors (TFETs), which can be fabricated by conventional CMOS technology. CS TFETs show lower subthreshold swing (SS) and higher on-state current than conventional TFETs through their high surface-to-volume ratio, which increases carrier-tunneling region with no additional device area. The on-state current can be enhanced by increasing the nanowire height, decreasing equivalent oxide thickness (EOT) or creating a nanowire array. The off-state current is also manageable for power saving through selective epitaxial growth at the top-side nanowire region. CS TFETs with an EOT of 0.8 nm and an aspect ratio of 20 for the core nanowire region provide the largest drain current ranges with point SS values below 60 mV/dec and superior on/off current ratio under all operation voltages of 0.5, 0.7, and 1.0 V. These devices are promising for low-power applications at low fabrication cost and high device density. PMID:28112273

  7. Implementing Silicon Nanoribbon Field-Effect Transistors as Arrays for Multiple Ion Detection

    Directory of Open Access Journals (Sweden)

    Ralph L. Stoop

    2016-05-01

    Full Text Available Ionic gradients play a crucial role in the physiology of the human body, ranging from metabolism in cells to muscle contractions or brain activities. To monitor these ions, inexpensive, label-free chemical sensing devices are needed. Field-effect transistors (FETs based on silicon (Si nanowires or nanoribbons (NRs have a great potential as future biochemical sensors as they allow for the integration in microscopic devices at low production costs. Integrating NRs in dense arrays on a single chip expands the field of applications to implantable electrodes or multifunctional chemical sensing platforms. Ideally, such a platform is capable of detecting numerous species in a complex analyte. Here, we demonstrate the basis for simultaneous sodium and fluoride ion detection with a single sensor chip consisting of arrays of gold-coated SiNR FETs. A microfluidic system with individual channels allows modifying the NR surfaces with self-assembled monolayers of two types of ion receptors sensitive to sodium and fluoride ions. The functionalization procedure results in a differential setup having active fluoride- and sodium-sensitive NRs together with bare gold control NRs on the same chip. Comparing functionalized NRs with control NRs allows the compensation of non-specific contributions from changes in the background electrolyte concentration and reveals the response to the targeted species.

  8. B-doped diamond field-effect transistor with ferroelectric vinylidene fluoride–trifluoroethylene gate insulator

    Science.gov (United States)

    Karaya, Ryota; Baba, Ikki; Mori, Yosuke; Matsumoto, Tsubasa; Nakajima, Takashi; Tokuda, Norio; Kawae, Takeshi

    2017-10-01

    A B-doped diamond field-effect transistor (FET) with a ferroelectric vinylidene fluoride–trifluoroethylene (VDF–TrFE) copolymer gate insulator was fabricated. The VDF–TrFE film deposited on the B-doped diamond showed good insulating and ferroelectric properties. Also, a Pt/VDF–TrFE/B-doped diamond layered structure showed ideal behavior as a metal–ferroelectric–semiconductor (MFS) capacitor, and the memory window width was 11 V, when the gate voltage was swept from 20 to ‑20 V. The fabricated MFS-type FET structure showed the typical properties of a depletion-type p-channel FET and a maximum drain current density of 0.87 mA/mm at room temperature. The drain current versus gate voltage curves of the proposed FET showed a clockwise hysteresis loop owing to the ferroelectricity of the VDF–TrFE gate insulator. In addition, we demonstrated the logic inverter with the MFS-type diamond FET coupled with a load resistor, and obtained the inversion behavior of the input signal and a maximum gain of 18.4 for the present circuit.

  9. Gold nanoparticles-decorated graphene field-effect transistor biosensor for femtomolar MicroRNA detection.

    Science.gov (United States)

    Cai, Bingjie; Huang, Le; Zhang, Hong; Sun, Zhongyue; Zhang, Zhiyong; Zhang, Guo-Jun

    2015-12-15

    Early detection is proven to be the best chance for successful cancer treatment. MiRNAs, as ideal biomarkers, can identify cancer in the early stage. Therefore, development of highly sensitive and selective detection methods for miRNA is still anticipated. Here we report on a gold nanoparticles (AuNPs)-decorated graphene field-effect transistor (FET) biosensor for highly sensitive, selective and label-free detection of miRNA. The AuNPs-decorated graphene FET biosensor was fabricated by drop-casting the reduced graphene oxide (R-GO) suspension onto the sensor surface, and subsequently decorating AuNPs onto the surface of R-GO. After peptide nucleic acid (PNA) probe was immobilized on the AuNPs surface, miRNA detection was carried out via PNA-miRNA hybridization. It was found that the developed FET biosensor was able to achieve a detection limit as low as 10 fM. In addition, the biosensor enabled an accurate distinction of complementary miRNA from one-base mismatched miRNA and noncomplementary miRNA. What's more, this highly sensitive and selective assay was also applied to the detection of miRNA in serum samples, making it a potential method for diagnosis of gene-related diseases.

  10. Detecting Electric Dipoles Interaction at the Interface of Ferroelectric and Electrolyte Using Graphene Field Effect Transistors.

    Science.gov (United States)

    Ma, Chunrui; Lu, Rongtao; Hu, Guangliang; Han, Jinsheng; Liu, Ming; Li, Jun; Wu, Judy

    2017-02-01

    Graphene was inserted into the interface between electric dipole layers from DEME-TFSI ionic liquid (top-gate) and ferroelectric Pb0.92La0.08Zr0.52Ti0.48O3 (PLZT, back-gate) to probe the interface dipole-dipole interaction in response to DC and pulsed gate voltages. A highly complicated behavior of the interface dipole-dipole interaction has been revealed as a combination of electrostatic and electrochemical effects. The interfacial polar molecules in the DEME-TFSI electrical double layer are pinned with assistance from the PLZT back-gate in response to a DC top-gate pump, leading to strong nonlinear electrochemical behavior. In contrast, depinning of these molecules can be facilitated by a faster pulsed top-gate pump, which results in a characteristic linear electrostatic behavior. This result not only sheds light on the dynamic dipole-dipole interactions on the interface between functional materials but also prototypes a unique pump and probe approach using graphene field effect transistors to detect the interface dipole-dipole interaction.

  11. First-principles simulations of Graphene/Transition-metal-Dichalcogenides/Graphene Field-Effect Transistor

    Science.gov (United States)

    Li, Xiangguo; Wang, Yun-Peng; Zhang, X.-G.; Cheng, Hai-Ping

    A prototype field-effect transistor (FET) with fascinating properties can be made by assembling graphene and two-dimensional insulating crystals into three-dimensional stacks with atomic layer precision. Transition metal dichalcogenides (TMDCs) such as WS2, MoS2 are good candidates for the atomically thin barrier between two layers of graphene in the vertical FET due to their sizable bandgaps. We investigate the electronic properties of the Graphene/TMDCs/Graphene sandwich structure using first-principles method. We find that the effective tunnel barrier height of the TMDC layers in contact with the graphene electrodes has a layer dependence and can be modulated by a gate voltage. Consequently a very high ON/OFF ratio can be achieved with appropriate number of TMDC layers and a suitable range of the gate voltage. The spin-orbit coupling in TMDC layers is also layer dependent but unaffected by the gate voltage. These properties can be important in future nanoelectronic device designs. DOE/BES-DE-FG02-02ER45995; NERSC.

  12. GaN nanowire arrays with nonpolar sidewalls for vertically integrated field-effect transistors

    Science.gov (United States)

    Yu, Feng; Yao, Shengbo; Römer, Friedhard; Witzigmann, Bernd; Schimpke, Tilman; Strassburg, Martin; Bakin, Andrey; Schumacher, Hans Werner; Peiner, Erwin; Suryo Wasisto, Hutomo; Waag, Andreas

    2017-03-01

    Vertically aligned gallium nitride (GaN) nanowire (NW) arrays have attracted a lot of attention because of their potential for novel devices in the fields of optoelectronics and nanoelectronics. In this work, GaN NW arrays have been designed and fabricated by combining suitable nanomachining processes including dry and wet etching. After inductively coupled plasma dry reactive ion etching, the GaN NWs are subsequently treated in wet chemical etching using AZ400K developer (i.e., with an activation energy of 0.69 ± 0.02 eV and a Cr mask) to form hexagonal and smooth a-plane sidewalls. Etching experiments using potassium hydroxide (KOH) water solution reveal that the sidewall orientation preference depends on etchant concentration. A model concerning surface bonding configuration on crystallography facets has been proposed to understand the anisotropic wet etching mechanism. Finally, NW array-based vertical field-effect transistors with wrap-gated structure have been fabricated. A device composed of 99 NWs exhibits enhancement mode operation with a threshold voltage of 1.5 V, a superior electrostatic control, and a high current output of >10 mA, which prevail potential applications in next-generation power switches and high-temperature digital circuits.

  13. Buffer transport mechanisms in intentionally carbon doped GaN heterojunction field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Uren, Michael J.; Cäsar, Markus; Kuball, Martin [Center for Device Thermography and Reliability, H.H. Wills Physics Laboratory, University of Bristol, Bristol BS8 1TL (United Kingdom); Gajda, Mark A. [NXP Semiconductors, Bramhall Moor Lane, Hazel Grove, Stockport SK7 5BJ (United Kingdom)

    2014-06-30

    Temperature dependent pulsed and ramped substrate bias measurements are used to develop a detailed understanding of the vertical carrier transport in the buffer layers in a carbon doped GaN power heterojunction field effect transistor. Carbon doped GaN and multiple layers of AlGaN alloy are used in these devices to deliver an insulating and strain relieved buffer with high breakdown voltage capability. However, understanding of the detailed physical mechanism for its operation is still lacking. At the lowest electric fields (<10 MV/m), charge redistribution within the C doped layer is shown to occur by hole conduction in the valence band with activation energy 0.86 eV. At higher fields, leakage between the two-dimensional electron gas and the buffer dominates occurring by a Poole-Frenkel mechanism with activation energy ∼0.65 eV, presumably along threading dislocations. At higher fields still, the strain relief buffer starts to conduct by a field dependent process. Balancing the onset of these leakage mechanisms is essential to allow the build-up of positive rather than negative space charge, and thus minimize bulk-related current-collapse in these devices.

  14. Heterogeneous nucleation promotes carrier transport in solution-processed organic field-effect transistors

    KAUST Repository

    Li, Ruipeng

    2012-09-04

    A new way to investigate and control the growth of solution-cast thin films is presented. The combination of in situ quartz crystal microbalance measurements with dissipation capabilities (QCM-D) and in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) in an environmental chamber provides unique quantitative insights into the time-evolution of the concentration of the solution, the onset of nucleation, and the mode of growth of the organic semiconductor under varied drying conditions. It is demonstrated that careful control over the kinetics of solution drying enhances carrier transport significantly by promoting phase transformation predominantly via heterogeneous nucleation and sustained surface growth of a highly lamellar structure at the solid-liquid interface at the expense of homogeneous nucleation. A new way to investigate and control the growth of drop-cast thin films is presented. The solution-processing of small-molecule thin films of TIPS-pentacene is investigated using time-resolved techniques to reveal the mechanisms of nucleation and growth leading to solid film formation. By tuning the drying speed of the solution, the balance between surface and bulk growth modes is altered, thereby controlling the lamellar formation and tuning the carrier mobility in organic field-effect transistors Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Graphene Field Effect Transistors for Biomedical Applications: Current Status and Future Prospects

    Directory of Open Access Journals (Sweden)

    Rhiannan Forsyth

    2017-07-01

    Full Text Available Since the discovery of the two-dimensional (2D carbon material, graphene, just over a decade ago, the development of graphene-based field effect transistors (G-FETs has become a widely researched area, particularly for use in point-of-care biomedical applications. G-FETs are particularly attractive as next generation bioelectronics due to their mass-scalability and low cost of the technology’s manufacture. Furthermore, G-FETs offer the potential to complete label-free, rapid, and highly sensitive analysis coupled with a high sample throughput. These properties, coupled with the potential for integration into portable instrumentation, contribute to G-FETs’ suitability for point-of-care diagnostics. This review focuses on elucidating the recent developments in the field of G-FET sensors that act on a bioaffinity basis, whereby a binding event between a bioreceptor and the target analyte is transduced into an electrical signal at the G-FET surface. Recognizing and quantifying these target analytes accurately and reliably is essential in diagnosing many diseases, therefore it is vital to design the G-FET with care. Taking into account some limitations of the sensor platform, such as Debye–Hükel screening and device surface area, is fundamental in developing improved bioelectronics for applications in the clinical setting. This review highlights some efforts undertaken in facing these limitations in order to bring G-FET development for biomedical applications forward.

  16. Graphene Field Effect Transistors for Biomedical Applications: Current Status and Future Prospects.

    Science.gov (United States)

    Forsyth, Rhiannan; Devadoss, Anitha; Guy, Owen J

    2017-07-26

    Since the discovery of the two-dimensional (2D) carbon material, graphene, just over a decade ago, the development of graphene-based field effect transistors (G-FETs) has become a widely researched area, particularly for use in point-of-care biomedical applications. G-FETs are particularly attractive as next generation bioelectronics due to their mass-scalability and low cost of the technology's manufacture. Furthermore, G-FETs offer the potential to complete label-free, rapid, and highly sensitive analysis coupled with a high sample throughput. These properties, coupled with the potential for integration into portable instrumentation, contribute to G-FETs' suitability for point-of-care diagnostics. This review focuses on elucidating the recent developments in the field of G-FET sensors that act on a bioaffinity basis, whereby a binding event between a bioreceptor and the target analyte is transduced into an electrical signal at the G-FET surface. Recognizing and quantifying these target analytes accurately and reliably is essential in diagnosing many diseases, therefore it is vital to design the G-FET with care. Taking into account some limitations of the sensor platform, such as Debye-Hükel screening and device surface area, is fundamental in developing improved bioelectronics for applications in the clinical setting. This review highlights some efforts undertaken in facing these limitations in order to bring G-FET development for biomedical applications forward.

  17. Radiation sensitivity of graphene field effect transistors and other thin film architectures

    Science.gov (United States)

    Cazalas, Edward

    An important contemporary motivation for advancing radiation detection science and technology is the need for interdiction of nuclear and radiological materials, which may be used to fabricate weapons of mass destruction. The detection of such materials by nuclear techniques relies on achieving high sensitivity and selectivity to X-rays, gamma-rays, and neutrons. To be attractive in field deployable instruments, it is desirable for detectors to be lightweight, inexpensive, operate at low voltage, and consume low power. To address the relatively low particle flux in most passive measurements for nuclear security applications, detectors scalable to large areas that can meet the high absolute detection efficiency requirements are needed. Graphene-based and thin-film-based radiation detectors represent attractive technologies that could meet the need for inexpensive, low-power, size-scalable detection architectures, which are sensitive to X-rays, gamma-rays, and neutrons. The utilization of graphene to detect ionizing radiation relies on the modulation of graphene charge carrier density by changes in local electric field, i.e. the field effect in graphene. Built on the principle of a conventional field effect transistor, the graphene-based field effect transistor (GFET) utilizes graphene as a channel and a semiconducting substrate as an absorber medium with which the ionizing radiation interacts. A radiation interaction event that deposits energy within the substrate creates electron-hole pairs, which modify the electric field and modulate graphene charge carrier density. A detection event in a GFET is therefore measured as a change in graphene resistance or current. Thin (micron-scale) films can also be utilized for radiation detection of thermal neutrons provided nuclides with high neutron absorption cross section are present with appreciable density. Detection in thin-film detectors could be realized through the collection of charge carriers generated within the

  18. The Substrate is a pH-Controlled Second Gate of Electrolyte-Gated Organic Field-Effect Transistor.

    Science.gov (United States)

    Di Lauro, Michele; Casalini, Stefano; Berto, Marcello; Campana, Alessandra; Cramer, Tobias; Murgia, Mauro; Geoghegan, Mark; Bortolotti, Carlo A; Biscarini, Fabio

    2016-11-23

    Electrolyte-gated organic field-effect transistors (EGOFETs), based on ultrathin pentacene films on quartz, were operated with electrolyte solutions whose pH was systematically changed. Transistor parameters exhibit nonmonotonic variation versus pH, which cannot be accounted for by capacitive coupling through the Debye-Helmholtz layer. The data were fitted with an analytical model of the accumulated charge in the EGOFET, where Langmuir adsorption was introduced to describe the pH-dependent charge buildup at the quartz surface. The model provides an excellent fit to the threshold voltage and transfer characteristics as a function of the pH, which demonstrates that quartz acts as a second gate controlled by pH and is mostly effective from neutral to alkaline pH. The effective capacitance of the device is always greater than the capacitance of the electrolyte, thus highlighting the role of the substrate as an important active element for amplification of the transistor response.

  19. Negative differential transconductance in silicon quantum well metal-oxide-semiconductor field effect/bipolar hybrid transistors

    Energy Technology Data Exchange (ETDEWEB)

    Naquin, Clint; Lee, Mark [Department of Physics, University of Texas at Dallas, Richardson, Texas 75080 (United States); Edwards, Hal; Mathur, Guru; Chatterjee, Tathagata; Maggio, Ken [Texas Instruments, Inc., Richardson, Texas 75243 (United States)

    2014-11-24

    Introducing explicit quantum transport into Si transistors in a manner amenable to industrial fabrication has proven challenging. Hybrid field-effect/bipolar Si transistors fabricated on an industrial 45 nm process line are shown to demonstrate explicit quantum transport signatures. These transistors incorporate a lateral ion implantation-defined quantum well (QW) whose potential depth is controlled by a gate voltage (V{sub G}). Quantum transport in the form of negative differential transconductance (NDTC) is observed to temperatures >200 K. The NDTC is tied to a non-monotonic dependence of bipolar current gain on V{sub G} that reduces drain-source current through the QW. These devices establish the feasibility of exploiting quantum transport to transform the performance horizons of Si devices fabricated in an industrially scalable manner.

  20. High-k dielectrics as bioelectronic interface for field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Borstlap, D.

    2007-03-15

    Ion-sensitive field-effect transistors (ISFETs) are employed as bioelectronic sensors for the cell-transistor coupling and for the detection of DNA sequences. For these applications, thermally grown SiO{sub 2} films are used as standard gate dielectric. In the first part of this dissertation, the suitability of high-k dielectrics was studied to increase the gate capacitance and hence the signal-to-noise ratio of bioelectronic ISFETs: Upon culturing primary rat neurons on the corresponding high-k dielectrics, Al{sub 2}O{sub 3}, yttria stabilised zirkonia (YSZ), DyScO{sub 3}, CeO{sub 2}, LaAlO{sub 3}, GdScO{sub 3} and LaScO{sub 3} proved to be biocompatible substrates. Comprehensive electrical and electrochemical current-voltage measurements and capacitance-voltage measurements were performed for the determination of the dielectric properties of the high-k dielectrics. In the second part of the dissertation, standard SiO{sub 2} ISFETs with lower input capacitance and high-k dielectric Al{sub 2}O{sub 3}, YSZ und DyScO{sub 3} ISFETs were comprehensively characterised and compared with each other regarding their signal-to-noise ratio, their ion sensitivity and their drift behaviour. The ion sensitivity measurements showed that the YSZ ISFETs were considerably more sensitive to K{sup +} and Na{sup +} ions than the SiO{sub 2}, Al{sub 2}O{sub 3} und DyScO{sub 3} ISFETs. In the final third part of the dissertation, bioelectronic experiments were performed with the high-k ISFETs. The shape of the signals, which were measured from HL-1 cells with YSZ ISFETs, differed considerably from the corresponding measurements with SiO{sub 2} and DyScO{sub 3} ISFETs: After the onset of the K{sup +} current, the action potentials measured with YSZ ISFETs showed a strong drift in the direction opposite to the K{sup +} current signal. First coupling experiments between HEK 293 cells, which were transfected with a K{sup +} ion channel, and YSZ ISFETs affirmed the assumption from the HL-1