WorldWideScience

Sample records for jt8d hub failure

  1. Pollution reduction technology program for class T4(JT8D) engines

    Science.gov (United States)

    Roberts, R.; Fiorentino, A. J.; Diehl, L. A.

    1977-01-01

    The technology required to develop commercial gas turbine engines with reduced exhaust emissions was demonstrated. Can-annular combustor systems for the JT8D engine family (EPA class T4) were investigated. The JT8D turbofan engine is an axial-flow, dual-spool, moderate-bypass-ratio design. It has a two-stage fan, a four-stage low-pressure compressor driven by a three-stage low-pressure turbine, and a seven-stage high-pressure compressor driven by a single-stage high-pressure turbine. A cross section of the JT8D-17 showing the mechanical configuration is given. Key specifications for this engine are listed.

  2. JT8D and JT9D jet engine performance improvement program. Task 1: Feasibility analysis

    Science.gov (United States)

    Gaffin, W. O.; Webb, D. E.

    1979-01-01

    JT8D and JT9D component performance improvement concepts which have a high probability of incorporation into production engines were identified and ranked. An evaluation method based on airline payback period was developed for the purpose of identifying the most promising concepts. The method used available test data and analytical models along with conceptual/preliminary designs to predict the performance improvements, weight, installation characteristics, cost for new production and retrofit, maintenance cost, and qualitative characteristics of candidate concepts. These results were used to arrive at the concept payback period, which is the time required for an airline to recover the investment cost of concept implementation.

  3. 75 FR 27972 - Airworthiness Directives; Pratt & Whitney JT8D-9, -9A, -11, -15, -17, and -17R Turbofan Engines

    Science.gov (United States)

    2010-05-19

    ..., MAN- JT8D-2-06 and the Engine Manual Chapter/Section 72-33-21, Inspection 00. Definitions (i) For the... the technical contents of PW JT8D Maintenance Advisory Notice MAN-JT8D-2-06, dated November 20, 2006... Advisory Notice, MAN-JT8D-2-06 and the Engine Manual Chapter/Section 72-33-21, Inspection 00. (g) For...

  4. Study of particle pumping characteristics for different pumping geometries in JT-60U and DIII-D divertors

    International Nuclear Information System (INIS)

    Takenaga, H.; Sakasai, A.; Kubo, H.

    2001-01-01

    Particle pumping characteristics were compared between pumping from the inner side private flux region (IPP) and pumping from both sides of the private flux region (BPP) in the JT-60U W shaped divertor, and between JT-60U IPP and pumping in the DIII-D lower baffled divertor. The pumping flux for BPP is smaller than that for IPP by about a factor of 2 with weak in-out asymmetry of recycling neutral flux and by a factor of 3.5-6.5 with strong in-out asymmetry. The reduction of the pumping flux for BPP is consistent with Monte Carlo simulations, where backflow at the outer pumping slot is observed due to in-out recycling asymmetry. The pumping flux in DIII-D at I p =0.8 MA and B T =1.6 T is comparable to or smaller than that for JT-60U IPP at I p =1.0 MA, B T =3.8 T and I p =1.5 MA, B T =3.5 T in the same density regime. In the DIII-D divertor with pumping from the private flux region, the pumping flux decreases with increasing in-out asymmetry. The pumping flux normalized by the integrated D α emission over the whole plasma exhibits a similar dependence on the distance between the pumping slot and the strike point in JT-60U IPP and the DIII-D lower divertor with pumping through the outer divertor plasma region. (author)

  5. Sharing Data between Mobile Devices, Connected Vehicles and Infrastructure Task 8 : D2X Hub Proof-of-Concept Test Evaluation Report.

    Science.gov (United States)

    2017-10-25

    The Task 8 D2X Hub Proof-of-Concept Test Evaluation Report provides results of the experimental data analysis performed in accordance with the experimental plan for the proof-of-concept version of the prototype system. The data set analyzed includes ...

  6. Construction and testing of JT-60

    International Nuclear Information System (INIS)

    Kishimoto, H.; Aikawa, H.; Oikawa, A.; Miya, N.; Suzuki, K.; Ozeki, T.; Tokutake, T.; Kunieda, S.; Hiruta, K.; Hosoda, R.

    1987-01-01

    The JT-60 project is reviewed in terms of design, R and D, construction, commissioning and project management. Design features of JT-60 have been refined and renewed through periodic assessments. Engineering targets have been achieved by R and D efforts. Construction and commissioning have progressed on schedule with intensive project management and control. JT-60 obtained high performance and has entered into the experimental phase after completion of machine construction. (orig.)

  7. Airline fuel saving through JT9D engine refurbishment

    Energy Technology Data Exchange (ETDEWEB)

    Allison, J.W.; Weisel, D.R.

    1981-01-01

    Areas are identified in the JT9D engine where the potential exists for either further performance recovery following repair, or for improved performance retention. A number of new procedures and tools which will improve performance recovery are described. Improvements in inspection techniques are discussed. Operational techniques which will improve performance retention and impact degree of refurbishment required are also presented.

  8. The design study of the JT-60SU device. No.8. Nuclear shielding and safety design

    Energy Technology Data Exchange (ETDEWEB)

    Miya, Naoyuki; Kikuchi, Mitsuru; Ushigusa, Kenkichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

    1998-03-01

    Results of nuclear shielding design study and safety analysis for the steady-state tokamak device JT-60SU are described. D-T operation (option) for two years is adopted in addition to ten years operation using deuterium. Design work has been done in accordance with general laws for radioisotopes handling in Japan as a guideline of safety evaluation, which is applied to the operation of present JT-60U device. Optimization of the shielding design for the device structure including vacuum vessel has been presented to meet with allowable limits of biological shielding determined in advance. It is shown that JT-60SU can be operated safely in the present JT-60 experimental building. It is planed to use 100g/year of tritium in D-T operation phase. A concept of multiple -barrier system is applied to the facility design to prevent propagation of tritium, in which the torus hall and the tritium removal room provide the tertiary confinement. From the design of atmosphere detritiation system for accidental tritium release, it is shown that tritium concentration level can be reduced to the allowable level after two weeks with reasonable compact size components. Safety assessment related to activation of coolant/air, and atmospheric tritium effluents are discussed. (author)

  9. Progress in JT-60 innovative technologies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-09-01

    This review report provides the synthetic archives of innovative technologies in 20-year facility developments for the large tokamak experimental device JT-60, first founded as the major magnetic fusion device in the Second Basic Program for Fusion Research and Development of Japan. Manufacture of JT-60 was started in 1978, and the first plasma was achieved on April 8, 1985. In 1989-1991, the vacuum vessel and poloidal field coils were entirely reconfigured to improve the plasma performance. The major original mission of the JT-60 project, a breakeven condition for a D-T equivalent plasma, was finally attained in 1996. After this, JT-60, as a leading device for magnetic fusion research in the world, continues to challenge many experimental issues, which has been achieved by collaboration of innovative facility developments and experimental improvements. In addition, at this time to start the ITER construction phase in 2005, this review is expected to contribute the construction and operation activities for the next generation tokamak by providing the basic ideas in facility developments. We classified a tremendous number of development items into the selected sections for this review. Since the authors have been in charge of each development activity of their own, the contents are full of essential stories, points, and keywords in spite of its compact handbook size. We believe this review could provide highly sophisticated, informative ideas matured in JT-60 technological developments. (author)

  10. Report on the design of JT-4

    International Nuclear Information System (INIS)

    Kitsunezaki, Akio; Seki, Shogo; Yokomizo, Hideaki; Matsuda, Toshiaki; Saito, Ryuta

    1978-08-01

    The present status of design of JT-4 tokamak is described. The objectives of JT-4 are shown graphically and the main parameters are tabulated. JT-4 is a tokamak of non-circular (ellipse or D-shape) plasma cross section with axisymmetric divertors at top and bottom of the plasma column. The principal purpose of JT-4 is to obtain high plasma beta values, desirably exceeding 5%, by strong secondary plasma heating and by impurities elimination. The experimental results obtained with JT-4 are essential in the design of future tokamaks and tokamak reactors with high efficiency and at reasonable cost. (author)

  11. Mutacin H-29B is identical to mutacin II (J-T8

    Directory of Open Access Journals (Sweden)

    Lavoie Marc C

    2006-04-01

    Full Text Available Abstract Background Streptococcus mutans produces bacteriocins named mutacins. Studies of mutacins have always been hampered by the difficulties in obtaining active liquid preparations of these substances. Some of them were found to be lantibiotics, defined as bacterial ribosomally synthesised lanthionine-containing peptides with antimicrobial activity. The goal of this study was to produce and characterize a new mutacin from S. mutans strain 29B, as it shows a promising activity spectrum against current human pathogens. Results Mutacin H-29B, produced by S. mutans strain 29B, was purified by successive hydrophobic chromatography from a liquid preparation consisting of cheese whey permeate (6% w/v supplemented with yeast extract (2% and CaCO3 (1%. Edman degradation revealed 24 amino acids identical to those of mutacin II (also known as J-T8. The molecular mass of the purified peptide was evaluated at 3246.08 ± 0.1 Da by MALDI-TOF MS. Conclusion A simple procedure for production and purification of mutacins along with its characterization is presented. Our results show that the amino acid sequence of mutacin H-29B is identical to the already known mutacin II (J-T8 over the first 24 residues. S. mutans strains of widely different origins may thus produce very similar bacteriocins.

  12. Heat structural problems in JT-60

    International Nuclear Information System (INIS)

    Takatsu, Hideyuki; Shimizu, Masaomi; Yamamoto, Masahiro; Nakamura, Hiroo; Miyauchi, Yasuyuki.

    1980-01-01

    The construction of JT-60 is in progress to study the behavior of hydrogen plasma. The D-T reaction does not occur in this device, therefore the considerations for neutron damage, tritium leakage and so on are not necessary. The long-pulse operation will be done, and the suppression of the production and mixing of impurity is considered in the design of the JT-60. The high temperature baking is possible, and the magnetic limiter is set. The vacuum container has the complex structure consists of 8 sector type thick rings and 8 U-shaped bellows, and has egg-shaped cross section. The main radius of the torus is about 3 m. The material of the vacuum container is INCONEL 625. The analyses of various stresses due to such as atmospheric pressure, eddy current and thermal expansion were made. It is also necessary to consider the thermal stress due to the leakage of neutral beam. The thermal input of about 20 MW per one discharge to the first wall is taken into consideration. The material of the first wall is molybdenum. (Kato, T.)

  13. Virtual Campus Hub technology

    DEFF Research Database (Denmark)

    Vercoulen, Frank; Badger, Merete; Monaco, Lucio

    This deliverable briefly describes which technological components have been delivered for the Virtual Campus Hub and how they can be used. A detailed discussion of the technical details of the components, how they were realized and how they fit the VCH concept can be found in deliverables D5.......4. Virtual Campus Hub Technology Evaluation Report and D6.7 The Virtual Campus Hub Concept....

  14. Development of magnetic sensors for JT-60SA

    Energy Technology Data Exchange (ETDEWEB)

    Takechi, M., E-mail: takechi.manabu@jaea.go.jp [Japan Atomic Energy Agency, Naka, Ibaraki 311-0193 (Japan); Matsunaga, G.; Sakurai, S.; Sasajima, T.; Yagyu, J.; Hoshi, R.; Kawamata, Y.; Kurihara, K. [Japan Atomic Energy Agency, Naka, Ibaraki 311-0193 (Japan); Nishikawa, T.; Ryo, T.; Kagamihara, S. [Okazaki Manufacturing Company, Kobe, Hyogo 651-0087 (Japan); Nakamura, K. [RIAM, Kyushu Univ., Kasuga, Fukuoka 816-8580,Japan (Japan)

    2015-10-15

    JT-60SA has been designed and is being constructed to demonstrate and develop steady-state high-beta operation. Resistive wall mode (RWM) control, error field correction, and edge-localized mode (ELM) control will be performed using in-vessel coils. For these controls, we have developed a biaxial magnetic sensor to determine 3D magnetic configuration of the plasma. Moreover, for obtaining basic information about JT-60SA plasma, magnetic sensors, in particular, one-turn loops, Rogowski coils, diamagnetic loops, and saddle coils have been developed. Because the length of the vacuum vessel in the poloidal direction of JT-60SA is 16 m and almost twice as long as that of JT-60U, the length of the Rogowski coil and the diamagnetic loop of JT-60SA are also twice as long as those on JT-60U. We have devised new types of sensors and a connector for the mineral-insulated cable because construction and installation of these sensors are much more difficult in JT-60SA. We will report the design and specification of the magnetic sensors for JT-60SA from the physics and engineering aspects.

  15. Aircraft Propeller Hub Repair

    Energy Technology Data Exchange (ETDEWEB)

    Muth, Thomas R [ORNL; Peter, William H [ORNL

    2015-02-13

    The team performed a literature review, conducted residual stress measurements, performed failure analysis, and demonstrated a solid state additive manufacturing repair technique on samples removed from a scrapped propeller hub. The team evaluated multiple options for hub repair that included existing metal buildup technologies that the Federal Aviation Administration (FAA) has already embraced, such as cold spray, high velocity oxy-fuel deposition (HVOF), and plasma spray. In addition the team helped Piedmont Propulsion Systems, LLC (PPS) evaluate three potential solutions that could be deployed at different stages in the life cycle of aluminum alloy hubs, in addition to the conventional spray coating method for repair. For new hubs, a machining practice to prevent fretting with the steel drive shaft was recommended. For hubs that were refurbished with some material remaining above the minimal material condition (MMC), a silver interface applied by an electromagnetic pulse additive manufacturing method was recommended. For hubs that were at or below the MMC, a solid state additive manufacturing technique using ultrasonic welding (UW) of thin layers of 7075 aluminum to the hub interface was recommended. A cladding demonstration using the UW technique achieved mechanical bonding of the layers showing promise as a viable repair method.

  16. Physical design of JT-60 Super Upgrade

    International Nuclear Information System (INIS)

    Nagashima, K.; Kikuchi, M.; Kurita, G.; Ozeki, T.; Aoyagi, T.; Ushigusa, K.; Neyatani, Y.; Kubo, T.; Mori, K.; Nakagawa, S.; Kuriyama, M.; Nagami, M.

    1997-01-01

    The JT-60 Super Upgrade (JT-60SU) is an upgraded tokamak device of JT-60U for developing the steady-state reactor and advanced tokamak operation in the International Thermonuclear Experimental Reactor. The device is planned to utilize the JT-60 facilities fully and to minimize the needed modification. The major radius is 4.8 m and the maximum plasma current is 10 MA. Neutral beam injection with 750 keV beam energy is the primary heating method. The machine is capable of steady-state operation with high density up to 8.8 x 10 19 m -3 at 5 MA plasma current. The high operating density, over the Greenwald et al. limit, is critically important in order to achieve high bootstrap current fraction. Ballooning mode and low n ideal magnetohydrodynamic (MHD) mode including the bootstrap current were analyzed for steady-state operation. The current profile must be optimized to obtain a normalized beta up to 3. The plasma configuration with high triangularity was adopted in order to get good MHD stability and high energy confinement. A compact divertor was designed in order to get the large plasma space. (orig.)

  17. Development of integrated SOL/Divertor code and simulation study of the JT-60U/JT-60SA tokamaks

    International Nuclear Information System (INIS)

    Kawashima, H.; Shimizu, K.; Takizuka, T.

    2007-01-01

    To predict the particle and heat controllability in the divertor of tokamak reactors such as ITER and to optimize the divertor design, comprehensive simulations by integrated modelling with taking in various physical processes are indispensable. For the design study of ITER divertor, the modelling codes such as B2, UEDGE and EDGE2D have been developed, and their results have contributed to the evolution of the divertor concept. In Japan Atomic Energy Agency (JAEA), SOL/divertor codes have also been developed for the interpretation and the prediction on behaviours of plasmas, neutrals and impurities in the SOL/divertor regions. The code development is originally carried out since physics models can be verified quickly and flexibly under the circumstance of close collaboration with JT-60 team. Figure 1 shows our code system, which consists of the 2 dimensional fluid code SOLDOR, the neutral Monte Carlo (MC) code NEUT2D, and the impurity MC code IMPMC. The particle simulation code PARASOL has also been developed in order to establish the physics modelling used in fluid simulations. Integration of SOLDOR, NEUT2D and IMPMC, called the '' SONIC '' code, is being carried out to simulate self-consistently the SOL/divertor plasmas in present tokamaks and in future devices. Combination of the SOLDOR and NEUT2D was completed, which has the features such as 1) high-resolution oscillation-free scheme in solving fluid equations, 2) neutral transport calculation under the fine meshes, 3) success in reduction of MC noise, 4) optimization on the massive parallel computer, etc. The simulation reproduces the X-point MARFE in the JT-60U experiment. It is found that the chemically sputtered carbon at the dome causes the radiation peaking near the X-point. The performance of divertor pumping in JT-60U is evaluated from the particle balances. We also present the divertor designing of JT-60SA, which is the modification program of JT-60U to establish high beta steady-state operation. To

  18. Simulation of collisional effects on divertor pumping in JT-60SA

    Energy Technology Data Exchange (ETDEWEB)

    Gleason-González, C., E-mail: cristian.gleason@kit.edu [Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, Baden-Württemberg 76344 (Germany); Varoutis, S.; Luo, X. [Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, Baden-Württemberg 76344 (Germany); Shimizu, K.; Nakano, T.; Hoshino, K.; Kawashima, H.; Asakura, N. [Japan Atomic Energy Agency, 801-1, Mukoyama, Naka, Ibaraki 311-0193 (Japan); Day, Chr. [Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, Baden-Württemberg 76344 (Germany); Sakurai, S. [Japan Atomic Energy Agency, 801-1, Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2016-11-01

    Highlights: • The exhausted (sub-divertor) gas flows calculations in tokamaks by means of three approaches: ProVac3D, DIVGAS and NEUT2D. • Exhausted neutral gas flow is modeled for two scenarios of a simplified JT-60SA sub-divertor geometry. • A modelled scenario with a simplified setup is done by using two intrinsic collisionless approaches: ProVac3D and NEUT2D and a third approach: DIVGAS, which has been used without its collision module for a direct comparison with the other two. The solvers are cross-checked in terms of the reproduction of the transmission probability. • A second case study is based on the Scenario # 2 of JT-60SA, where the assessment of collisionality in the sub-divertor was done. The gas flow is simulated by using DIVGAS with and without consideration of collisions. • The results include the transmission probability in JT-60SA sub-divertor, the Knudsen number, which characterizes the collisionality of the flow, velocity profiles, pressure and temperature distributions. - Abstract: In this work, the exhausted neutral gas flow is modeled for two cases of a simplified JT-60SA sub-divertor geometry and compared via three different approaches, namely (i) a collisionless approach based on the ProVac3D code, (ii) the DSMC approach based on the DIVGAS code that can be run with and without consideration of particle collisions, and (iii) the NEUT2D approach which has been extensively used in the past for the JT-60 design. In a first case study, the transmission probability was calculated by the 3 approaches and very good agreement is found between NEUT2D-ProVac3D whereas discrepancies between DIVGAS and NEUT2D are found and further analyzed. In the second case, the assessment of collisions is done by means of DIVGAS. Simulations showed that the flow is found in the transitional regime with Kn numbers between 0.1 and 0.4. The DIVGAS collisionless case yielded lower values of temperature than the collisional one by factors of 0.5–0.8 in

  19. Fabrication of the vacuum vessel for JT-60 machine upgrade

    International Nuclear Information System (INIS)

    Uchikawa, T.; Takanabe, K.; Tsujimura, S.; Ue, K.; Oka, K.; Kuri, S.; Ioki, K.; Namiki, K.; Suzuki, Y.; Horliike, H.; Ninomiya, H.; Yamamoto, M.; Neyatani, Y.; Ando, T.; Matsukawa, M.

    1992-01-01

    The JT-60 tokamak was upgraded to double the plasma current to 6 MA. In the JT-60 machine upgrade (JT-60U), the vacuum vessel and poloidal field (PF) coils were renewed. The new vacuum vessel features a three-dimensionally curved, thin double-skin torus with multi-arc D-shaped cross section. The double-skin structure is strengthened with square pipes placed in between the outer and inner skins. Fabrication and site installation of the vessel was smoothly completed in February, 1991. This paper describes an overview of the JT-60U vacuum vessel construction

  20. Development of fast opening magnetic valve for JT-60 pellet injector

    International Nuclear Information System (INIS)

    Hiratsuka, Hajime; Kawasaki, Kouzo; Takatsu, Hideyuki; Miyo, Yasuhiko; Yoshioka, Yuji; Ohta, Kazuya; Shimizu, Masatsugu; Onozuka, Masanori; Uchikawa, Takashi; Iwamoto, Syuichi; Hashiri, Noboru

    1989-01-01

    A pneumatic four-pellet injector (JT-60 pellet injector) has been constructed for JT-60 in May, 1988. A fast opening magnetically driven propellant gas injection valve has been developed for JT-60 pellet injector. This valve can accelerate four cylindrical pellets, two 3.8 mm diameter by 3.8 mm and two 2.7 mm diameter by 2.7 mm, to greater than 1.6 km/s with propellent gas of up to 50 bar. It is now successfully in use in JT-60, contributing to plasma studies. In this paper the outline of a newly developed fast opening magnetic valve and the results of performance tests are presented. (author). 6 figs.; 1 tab

  1. Accomplishment of JT-60U disassembly work dealing with radioactive components

    International Nuclear Information System (INIS)

    Ikeda, Yoshitaka

    2015-01-01

    The upgrade of the JT-60U to the superconducting tokamak 'JT-60SA' has been carried out to contribute the early realization of fusion energy by addressing key physics issues relevant for ITER and DEMO. Disassembly of the JT-60U tokamak was required so as to newly install the JT-60SA torus at the same position in the torus hall. The JT-60U tokamak was featured by the complicated and welded structure against the strong electromagnetic force, and by the radioactivation due to deuterium-deuterium (D-D) reactions of 1.5x10"2"0 (n) in total. Since this work was the first experience of disassembling a large radioactivated fusion device in Japan, careful preparations of disassembly activities, including treatment of the radioactivated materials and safety work, have been made. About 13,000 components with a total weight of more than 5,400 tonnes were removed from the torus hall and stored safely in storage facilities. All disassembly components were stored with recording the data such as dose rate, weight and kind of material, so as to apply the clearance level regulation in future. It was confirmed that the main radioactive material of the disassembly components was the stainless steel and that its dose rate was almost background level (∼0.1 μSv/h) at ∼10 m far from the vacuum vessel. It seems that the disassembly components with background dose level are in the clearance level. The assembly of JT-60SA tokamak has started in January 2013 after this disassembly of the JT-60U tokamak. (author)

  2. Development of JT-60 diagnostics system

    International Nuclear Information System (INIS)

    Suzuki, Yasuo

    1988-01-01

    The various kinds of plasma diagnostics have been developed and utilized in the JT-60 experiments. The features of JT-60 diagnostics system and the historical proceeding of the development are described in this paper. Taking account of the design consideration, JT-60 diagnostics system is sorted out into eight groups, which include six diagnostics systems, the data processing system and diagnostics supporting system. The all devices in the JT-60 diagnostics system were instrumented on schedule in the end of the fiscal year of 1985 and have contributed to JT-60 experiments. (author)

  3. Data Collection and Management with ENSITE HUB: ENSITE HUB Version 1.0

    Science.gov (United States)

    2017-08-01

    ER D C/ CE RL S R- 17 -1 4 Engineer Site Identification for the Tactical Environment (ENSITE) Data Collection and Management with ENSITE...and Management with ENSITE HUB ENSITE HUB Version 1.0 Juliana M. Wilhoit, Natalie R. Myers, and George W. Calfas Construction Engineering Research...and standardized manner. With such a tool, CB planners (as well as designers, operators, and manag - ers) can rapidly assess possible current and

  4. Advanced fusion technologies developed for JT-60 superconducting tokamak

    International Nuclear Information System (INIS)

    Sakasai, Akira; Ishida, S.; Matsukawa, M.

    2003-01-01

    The modification of JT-60U is planned as a full superconducting tokamak (JT-60SC). The objectives of the JT-60SC program are to establish scientific and technological bases for the steady-state operation of high performance plasmas and utilization of reduced-activation materials in economically and environmentally attractive DEMO reactor. Advanced fusion technologies relevant to DEMO reactor have been developed in the superconducting magnet technology and plasma facing components for the design of JT-60SC. To achieve a high current density in a superconducting strand, Nb 3 Al strands with a high copper ratio of 4 have been newly developed for the toroidal field coils (TFC) of JT-60SC. The R and D to demonstrate applicability of Nb 3 Al conductor to the TFC by a react-and-wind technique have been carried out using a full-size Nb 3 Al conductor. A full-size NbTi conductor with low AC loss using Ni-coated strands has been successfully developed. A forced cooling divertor component with high heat transfer using screw tubes has been developed for the first time. The heat removal performance of the CFC target was successfully demonstrated on the electron beam irradiation stand. (author)

  5. Development of the pellet injector for JT-60

    International Nuclear Information System (INIS)

    Kawasaki, Kouzo; Hiratsuka, Hajimo; Takatsu, Hideyuki; Shimizu, Masatsugu; Onozuka, Masanori; Uchikawa, Takashi; Iwamoto, Syuichi; Hashiri, Nobuo

    1989-01-01

    The pneumatic 4-shot pellet injector has been installed and operated for JT-60 (JAERI Tokamak-60). The performance tests have proved that the device provides high speed hydrogen pellets just as planned. The maximum pellet velocity obtained in the hydrogen pellet tests is greater than 1.6 km/sec at 50 bar propellant gas. The device is now in use for JT-60 contributing to plasma study. In this paper the outline of features and performance of the device is presented. (author). 4 refs.; 8 figs

  6. Quadratic Assignment of Hubs in p-Hub Median Problem

    DEFF Research Database (Denmark)

    Gelareh, Shahin

    We introduce Generalized p-Hub Median Problem (GpHMP) that seeks to locate p hub nodes and install p distinct hub facilities/operators on the hubs while discount factor resulted by consolidation of flow on the hub links depends on the facilities/operators that are installed/operating on both hub...

  7. FIR-laser scattering for JT-60

    International Nuclear Information System (INIS)

    Itagaki, Tokiyoshi; Matoba, Tohru; Funahashi, Akimasa; Suzuki, Yasuo

    1977-09-01

    An ion Thomson scattering method with far infrared (FIR) laser has been studied for measuring the ion temperature in large tokamak JT-60 to be completed in 1981. Ion Thomson scattering has the advantage of measuring spatial variation of the ion temperature. The ion Thomson scattering in medium tokamak (PLT) and future large tokamak (JET) requires a FIR laser of several megawatts. Research and development of FIR high power pulse lasers with power up to 0.6 MW have proceeded in ion Thomson scattering for future high-temperature tokamaks. The FIR laser power will reach to the desired several megawatts in a few years, so JAERI plans to measure the ion temperature in JT-60 by ion Thomson scattering. A noise source of the ion Thomson scattering with 496 μm-CH 3 F laser is synchrotron radiation of which the power is similar to NEP of the Schottky-barrier diode. However, the synchrotron radiation power is one order smaller than that when a FIR laser is 385 μm-D 2 O laser. The FIR laser power corresponding to a signal to noise ratio of 1 is about 4 MW for CH 3 F laser, and 0.4 MW for D 2 O laser if NEP of the heterodyne mixer is one order less. A FIR laser scattering system for JT-60 should be realized with improvement of FIR laser power, NEP of heterodyne mixer and reduction of synchrotron radiation. (auth.)

  8. Disassembly of JT-60 tokamak device and ancillary facilities for JT-60 tokamak

    International Nuclear Information System (INIS)

    Okano, Fuminori; Ichige, Hisashi; Miyo, Yasuhiko; Kaminaga, Atsushi; Sasajima, Tadayuki; Nishiyama, Tomokazu; Yagyu, Jun-ichi; Ishige, Youichi; Suzuki, Hiroaki; Komuro, Kenichi; Sakasai, Akira; Ikeda, Yoshitaka

    2014-03-01

    The disassembly of JT-60 tokamak device and its peripheral equipments, where the total weight was about 5400 tons, started in 2009 and accomplished in October 2012. This disassembly was required process for JT-60SA project, which is the Satellite Tokamak project under Japan-EU international corroboration to modify the JT-60 to the superconducting tokamak. This work was the first experience of disassembling a large radioactive fusion device based on Radiation Hazard Prevention Act in Japan. The cutting was one of the main problems in this disassembly, such as to cut the welded parts together with toroidal field coils, and to cut the vacuum vessel into two. After solving these problems, the disassembly completed without disaster and accident. This report presents the outline of the JT-60 disassembly, especially tokamak device and ancillary facilities for tokamak device. (author)

  9. JT Bachman Leadership Framework

    Science.gov (United States)

    2017-07-01

    DAHLGREN DIVISION NAVAL SURFACE WARFARE CENTER Dahlgren, Virginia 22448-5100 NSWCDD/MP-17/300 JT BACHMAN LEADERSHIP FRAMEWORK...REPORT TYPE Miscellaneous Publication 3. DATES COVERED (From - To) 27 Sept 2016 – 08 June 2017 4. TITLE AND SUBTITLE JT BACHMAN LEADERSHIP FRAMEWORK...distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT This document describes the leadership framework of a civil servant following

  10. Nonlinear analysis of the GFRP material wheel hub

    Directory of Open Access Journals (Sweden)

    Dong Yun-Feng

    2015-01-01

    Full Text Available In this paper, the current bicycle wheel was replaced by the ones which composed by the wheel hub with Glassfiber Reinforced Plastic (alkali free thin-walled cylinder material, hereinafter referred to as GFRP material and the protective components made up of rubber outer pneumatic pad. With the help of the basic theory of elastic-plastic mechanics, the finite element “Nonlinear buckling” analysis of the wheel was carried out. The results show that the maximum elastic deformation of the wheel hub and the critical value of buckling failure load were restricted by the elasticity under the condition of external loads. Considering with the tensile strength and elastic modulus of the GFRP value of the material, it is demonstrated that the material is feasible to be used for wheel hub.

  11. Retention characteristics of hydrogen isotopes in JT-60U

    International Nuclear Information System (INIS)

    Masaki, K.; Sugiyama, K.; Hayashi, T.; Ochiai, K.; Gotoh, Y.; Shibahara, T.; Hirohata, Y.; Oya, Y.; Miya, N.; Tanabe, T.

    2005-01-01

    Erosion/deposition distribution and hydrogen isotope behavior in the JT-60U plasma-facing wall were investigated. Distribution of the tritium, which was produced by D-D nuclear reaction, was not correlated with erosion/deposition distribution. The tritium distribution can be explained by the distribution of high-energy tritium ion-implantation due to ripple loss. Deuterium distribution in the divertor region was different from the tritium distribution and not well correlated with the deposition. The highest D/C was ∼0.05 at the bottom of the outer dome wing, which is much less than that observed in other tokamaks. For the deuterium retention, at least two retention processes (ion-implantation and co-deposition) were found on the dome region. The systematic dust collection gave the small amount of dust (∼7 g: 0.2 mg/s production) in the whole vessel of JT-60U. Deposition was observed at the remote area of the outer divertor region

  12. Mock-up test results of monoblock-type CFC divertor armor for JT-60SA

    Energy Technology Data Exchange (ETDEWEB)

    Higashijima, S. [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)], E-mail: higashijima.satoru@jaea.go.jp; Sakurai, S.; Suzuki, S.; Yokoyama, K.; Kashiwa, Y.; Masaki, K.; Shibama, Y.K.; Takechi, M.; Shibanuma, K.; Sakasai, A.; Matsukawa, M.; Kikuchi, M. [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2009-06-15

    The JT-60 Super Advanced (JT-60SA) tokamak project starts under both the Japanese domestic program and the international program 'Broader Approach'. The maximum heat flux to JT-60SA divertor is estimated to {approx}15 MW/m{sup 2} for 100 s. Japan Atomic Energy Agency (JAEA) has developed a divertor armor facing high heat flux in the engineering R and D for ITER, and it is concluded that monoblock-type CFC divertor armor is promising for JT-60SA. The JT-60SA armor consists of CFC monoblocks, a cooling CuCrZr screw-tube, and a thin oxygen-free high conductivity copper (OFHC-Cu) buffer layer between the CFC monoblock and the screw-tube. CFC/OFHC-Cu and OFHC-Cu/CuCrZr joints are essential for the armor, and these interfaces are brazed. Needed improvements from ITER engineering R and D are good CFC/OFHC-Cu and OFHC-Cu/CuCrZr interfaces and suppression of CFC cracking. For these purposes, metalization inside CFC monoblock is applied, and we confirmed again that the mock-up has heat removal capability in excess of ITER requirement. For optimization of the fabrication method and understanding of the production yield, the mock-ups corresponding to quantity produced in one furnace at the same time is also produced, and the half of the mock-ups could remove 15 MW/m{sup 2} as required. This paper summarizes the recent progress of design and mock-up test results for JT-60SA divertor armor.

  13. Development and Operational Experiences of the JT-60U Tokamak and Power Supplies

    International Nuclear Information System (INIS)

    Hosogane, N.; Ninomiya, H.; Matsukawa, M.; Ando, T.; Neyatani, Y.; Horiike, H.; Sakurai, S.; Masaki, K.; Yamamoto, M.; Kodama, K.; Sasajima, T.; Terakado, T.; Ohmori, S.; Ohmori, Y.; Okano, J.

    2002-01-01

    The design of the JT-60U tokamak, the configuration of the coil power supplies, and the operational experiences gained to date are reviewed. JT-60U is a large tokamak upgraded from the original JT-60 in order to obtain high plasma current, large plasma volume, and highly elongated divertor configurations. All components inside the toroidal magnetic field coils, such as vacuum vessel, poloidal magnetic field coils, divertor, etc., were modified. Various technologies and ideas were introduced to develop these components; for example, a multi-arc double skin wall structure for the vacuum vessel and a functional poloidal magnetic field coil system with taps for obtaining various plasma configurations. Furthermore, boron-carbide coated carbon fiber composite (CFC) tiles were used as divertor tiles to reduce erosion of carbon-base tiles. Later, a semiclosed divertor with pumps, for which cryo-panels originally used for NBI units were converted, was installed in the replacement of the open divertor. These development and operational results provide data for future tokamaks. Major failures experienced in the long operational period of JT-60U, such as water leakage from the toroidal magnetic field coil, fracture of carbon tiles, and breakdown of a filter capacitor, are described. As a maintenance issue for tokamaks using deuterium fueling gas, a method for reducing radiation exposure of in-vessel workers is described

  14. Power and particle control in JT-60SA to support and supplement ITER and DEMO

    International Nuclear Information System (INIS)

    Sakurai, Shinji

    2007-01-01

    JT-60 is planned to be modified as a fully superconducting coil tokamak (JT-60 Super Advanced, JT-60SA). Divertor targets are water-cooled to handle heat flux up to 15 MW/m 2 . JT-60SA allows exploitation of high beta regime with stabilizing shell covered with ferritic plates and internal resistive wall mode (RWM) stabilizing coils. A remote handling system is equipped to maintain in-vessel components even for high dose rate due to a substantial annual neutron production. Divertor cassettes are introduced to be maintained by a remote handling. In the present design, a monoblock type carbon fibre composite (CFC) divertor target will be used to withstand a heat load of ∼15 MW/m 2 . CFC divertor targets and other bolted armor tiles will be mounted on the divertor cassette. All of the plasma facing components including the first wall armor are water-cooled to handle heat load during 100s or more. Divertor heat load and pumping efficiency for an ITER-like configuration has been evaluated, using 2D plasma fluid (SOLDOR) and neutral Monte-Carlo (NEUT2D) code. The pumping speed of 50 m 3 /s is specified at an albedo for neutrals in front of the in-vessel cryopanel. In the simulation for the divertor with a V -shaped corner' like as that in ITER, the plasma detachment occurs near the outer-strike point within the 'V-shaped corner', as well as near the inner-strike point, which results in low peak heat flux density 5.8 MW/m 2 for the case with additional gas puff of 5x10 21 /s compared to 11.4 MW/m 2 for the case without 'V-shaped corner'. (author)

  15. Overview of engineering design, manufacturing and assembly of JT-60SA machine

    Energy Technology Data Exchange (ETDEWEB)

    Di Pietro, Enrico, E-mail: enrico.dipietro@jt60sa.org [JT-60SA EU Home Team, Fusion for Energy, Boltzmannstrasse 2, Garching 85748 (Germany); Barabaschi, Pietro [JT-60SA EU Home Team, Fusion for Energy, Boltzmannstrasse 2, Garching 85748 (Germany); Kamada, Yutaka [JT-60SA JA Home Team, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Ishida, Shinichi [JT-60SA JA Project Team, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2014-10-15

    The JT-60SA experiment is one of the three projects to be undertaken in Japan as part of the Broader Approach Agreement, conducted jointly by Europe and Japan, and complementing the construction of ITER in Europe. The JT-60SA device is a fully superconducting tokamak capable of confining break-even equivalent deuterium plasmas with equilibria covering high plasma shaping with a low aspect ratio at a maximum plasma current of I{sub p} = 5.5 MA. This makes JT-60SA capable to support and complement ITER in all the major areas of fusion plasma development necessary to decide DEMO reactor construction. After a complex start-up phase due to the necessity to carry out a re-baselining effort with the purpose to fit in the original budget while aiming to retain the machine mission, performance, and experimental flexibility, in 2009 detailed design could start. With the majority of time-critical industrial contracts in place, in 2012, it was possible to establish a credible time plan, and now, the project is progressing on schedule towards the first plasma in March 2019. After careful and focused R and D and qualification tests, the procurement of the major components and plant is now well advanced in manufacturing design and/or fabrication. In the meantime the disassembly of the JT-60U machine has been completed and the engineering of the JT-60SA assembly process has been developed. The actual assembly of JT-60SA started in January 2013 with the installation of the cryostat base. The paper gives an overview of the present status of the engineering design, manufacturing and assembly of the JT-60SA machine.

  16. Vitamin D and Heart Failure.

    Science.gov (United States)

    Marshall Brinkley, D; Ali, Omair M; Zalawadiya, Sandip K; Wang, Thomas J

    2017-10-01

    Vitamin D is principally known for its role in calcium homeostasis, but preclinical studies implicate multiple pathways through which vitamin D may affect cardiovascular function and influence risk for heart failure. Many adults with cardiovascular disease have low vitamin D status, making it a potential therapeutic target. We review the rationale and potential role of vitamin D supplementation in the prevention and treatment of chronic heart failure. Substantial observational evidence has associated low vitamin D status with the risk of heart failure, ventricular remodeling, and clinical outcomes in heart failure, including mortality. However, trials assessing the influence of vitamin D supplementation on surrogate markers and clinical outcomes in heart failure have generally been small and inconclusive. There are insufficient data to recommend routine assessment or supplementation of vitamin D for the prevention or treatment of chronic heart failure. Prospective trials powered for clinical outcomes are warranted.

  17. Wave Transformation for International Hub Port Planning (Transformasi Gelombang untuk Perencanaan Pelabuhan Hub Internasional

    Directory of Open Access Journals (Sweden)

    Denny Nugroho Sugianto

    2015-02-01

    Full Text Available Indonesia merupakan salah satu negara kepulauan terbesar di dunia sehingga peran pelabuhan sangat vital dalam pembangunan ekonomi. Pelabuhan bukan hanya sekedar sebagai pelengkap infrastruktur, melainkan harus direncanakan dan dikelola dengan baik serta memperhatikan fenomena dinamika perairan laut seperti pola gelombang laut. Data gelombang laut menjadi faktor penting dalam perencanaan tata letak dan tipe bangunan pantai karena dipengaruhi oleh tinggi gelombang signifikan, tunggang pasang surut dan transformasi gelombang. Penelitian ini mengalisis karaketristrik dan bentuk transformasi gelombang untuk perencanaan Pelabuhan Hub Internasional, sebagai studi kasus adalah pelabuhan di Kuala Tanjung, Kabupaten Batu Bara. Pelabuhan di Kuala Tanjung merupakan salah satu dari 2 pelabuhan hub internasional yang direncanakan akan dibangun oleh pemerintah Indonesia. Metode yang digunakan adalah metode kuantitatif yang dilakukan dengan perhitungan statistik dan pemodelan matematik dengan modul hydrodinamic dan spectral wave untuk mengetahui arah penjalaran dan transformasi gelombang. Hasil dari data ECMWF selama 1999–Juni 2014, diketahui tinggi gelombang signifikan (Hs maksimum mencapai 1,69 m dan periode maksimum 8 detik. Karakteristik gelombang termasuk klasifikasi gelombang laut transisi dengan nilai d.L-1 berkisar anrata 0,27–0,48 dan berdasarkan periodenya diklasifikasikan sebagai gelombang gravitasi.Transformasi gelombang terjadi akibat pendangkalan dengan koefesian pendangkalan Ks 0,93–0,98 dan proses refraksi gelombang dengan koefesien Kr 0,97–0,99. Tinggi gelombang pecah Hb sebesar 1,24 meter dengan kedalaman gelombang pecah db sebesar 1,82 meter. Efektifitas desain bangunan terminal di Pelabuhan Kuala Tanjung secara keseluruhan untuk sepanjang musim sebesar 79,8% atau dapat dikatakan cukup efektif dalam meredam gelombang. Kata kunci: transformasi gelombang, tinggi dan periode gelombang, pelabuhan Indonesia is one of the largest

  18. Data Processing and Analysis Systems for JT-60U

    International Nuclear Information System (INIS)

    Matsuda, T.; Totsuka, T.; Tsugita, T.; Oshima, T.; Sakata, S.; Sato, M.; Iwasaki, K.

    2002-01-01

    The JT-60U data processing system is a large computer complex gradually modernized by utilizing progressive computer and network technology. A main computer using state-of-the-art CMOS technology can handle ∼550 MB of data per discharge. A gigabit ethernet switch with FDDI ports has been introduced to cope with the increase of handling data. Workstation systems with VMEbus serial highway drivers for CAMAC have been developed and used to replace many minicomputer systems. VMEbus-based fast data acquisition systems have also been developed to enlarge and replace a minicomputer system for mass data.The JT-60U data analysis system is composed of a JT-60U database server and a JT-60U analysis server, which are distributed UNIX servers. The experimental database is stored in the 1TB RAID disk of the JT-60U database server and is composed of ZENKEI and diagnostic databases. Various data analysis tools are available on the JT-60U analysis server. For the remote collaboration, technical features of the data analysis system have been applied to the computer system to access JT-60U data via the Internet. Remote participation in JT-60U experiments has been successfully conducted since 1996

  19. Engineering study of the neutral beam and rf heating systems for DIII-D, MFTF-B, JET, JT-60 and TFTR

    International Nuclear Information System (INIS)

    Lindquist, W.B.; Staten, S.H.

    1987-01-01

    An engineering study was performed on the rf and neutral beam heating systems implemented for DIII-D, MFTF-B, JET, JT-60 and TFTR. Areas covered include: methodology used to implement the systems, technology, cost, schedule, performance, problems encountered and lessons learned. Systems are compared and contrasted in the areas studied. Summary statements were made on common problems and lessons learned. 3 refs., 6 tabs

  20. Studies on first wall and plasma wall interaction in JT-60

    International Nuclear Information System (INIS)

    Nakamura, Hiroo

    1988-12-01

    This paper describes studies on first wall and plasma wall interaction in JT-60. Main results are as follows; (1) To select JT-60 first wall material, various RandD were done in FY1975 ∼ 1976. Mo was selected as first wall materials of limiters and divertor plates because of its reliability under a high heat flux condition. (2) Development of low-Z material has been done to reduce impurity problem of Mo first wall. As a result, titanium carbide (TiC) was selected as a coating material on the Mo. High heat load testing has been done for TiC coated Mo limiter same as JT-60. This material can survive under the condition of 1 kW/cm 2 x 10 s, expected in JT-60 limiter design. (3) To reduce high heat load on the divertor plate, separatrix swing is proposed. Optimum frequency of the sweeping is evaluated to be 2 Hz in JT-60. For a discharge with heating power of 30 MW and duration time of 10 s, in addition to the separatrix swing, remote radiative cooling in the divertor region is necessary. Moreover, calculations of erosion thickness have been done for stainless steel, Mo, graphite, TiC and silicon caibide under high heat flux during plasma disruption. (4) In divertor experiments in JT-60, divertor functions on particle, heat load and impurity controls have been demonstrated. In elctron density of 6 x 10 19 m -3 , particle fueling rate of 20 MW NB heating (3 Pa m 3 /s) can be exhausted by divertor pumping system. Effectiveness of remote radiative cooling is demonstrated under the condition of 20 MW NB heating power. Also, separatrix swing is demonstrated to reduce heat load on the divertor plate. Total radiation in main plasma is 5 ∼ 10% of total absorbed power. (author) 120 refs

  1. Tritium processing in JT-60U

    International Nuclear Information System (INIS)

    Miya, Naoyuki; Masaki, Kei

    1997-01-01

    Tritium retention analysis and tritium concentration measurement have been made during the large Tokamak JT-60U deuterium operations. This work has been carried out to evaluate the tritium retention for graphite tiles inside the vacuum vessel and tritium release characteristics in the tritium cleanup operations. JT-60U has carried out D-D experiments since July 1991. In the deuterium operations during the first two years, about 1.7 x 10 19 D-D fusion neutrons were produced by D (d, p) T reactions in plasma, which are expected to produce ∼31 GBq of tritium. The tritium produced is evacuated by a pumping system. A part of tritium is, however, trapped in the graphite tiles. Several sample tiles were removed from the vessel and the retained tritium Distribution in the tiles was measured using a liquid scintillator. The results of poloidal distribution showed that the tritium concentration in the divertor tiles was higher than that in the first wall tiles and it peaked in the tiles between two strike points of divertor magnetic lines. Tritium concentration in the exhaust gas from the vessel have also been measured with an ion chamber during the tritium cleanup operations with hydrogen divertor discharges and He-GDC. Total of recovered tritium during the cleanup operations was ∼ 7% of that generated. The results of these measurements showed that the tritium of 16-23 GBq still remained in the graphite tiles, which corresponded to about 50-70% of the tritium generated in plasma. The vessel is ventilated during the in-vessel maintenance works, then the atmosphere is always kept lower than the legal concentration guide level of 0.7 Bq/cm 3 for radiation work permit requirements. (author)

  2. Assembly work and transport of JT-60SA cryostat base

    International Nuclear Information System (INIS)

    Okano, Fuminori; Masaki, Kei; Yagyu, Jun-ichi; Shibama, Yusuke; Sakasai, Akira; Miyo, Yasuhiko; Kaminaga, Atsushi; Nishiyama, Tomokazu; Suzuki, Sadaaki; Nakamura, Shigetoshi; Shibanuma, Kiyoshi

    2013-11-01

    Japan Atomic Energy Agency started to construct a fully superconducting tokamak experiment device, JT-60SA, to support the ITER since January, 2013 at the Fusion Research and Development Directorate in Naka, Japan. The JT-60SA will be constructed with enhancing the previous JT-60 infrastructures, in the JT-60 torus hall, where the ex-JT-60 machine was disassembled. The JT-60SA Cryostat Base, for base of the entire tokamak structure, were assembly as the first step of this construction. The Cryostat Base (CB, 250tons) is consists of 7 main components made of stainless steel, in 12 m diameter and 3 m height. The CB was built in the Spain and transported to the Naka site, via Hitachi port. After pre-assembly work including preliminary measurements and sole plate adjustments of its height/flatness, the JT-60SA CB was carefully set on the sole plate. JT-60SA CB was assembled with high accuracy by using a laser tracker. The CB was adjusted in the height and flatness against the assembly reference position and determined by the absolute coordinates. This report introduces the concrete result of assembly work and transport of JT-60SA CB. (author)

  3. User's manual of JT-60 experimental data analysis system

    International Nuclear Information System (INIS)

    Hirayama, Takashi; Morishima, Soichi; Yoshioka, Yuji

    2010-02-01

    In the Japan Atomic Energy Agency Naka Fusion Institute, a lot of experiments have been conducted by using the large tokamak device JT-60 aiming to realize fusion power plant. In order to optimize the JT-60 experiment and to investigate complex characteristics of plasma, JT-60 experimental data analysis system was developed and used for collecting, referring and analyzing the JT-60 experimental data. Main components of the system are a data analysis server and a database server for the analyses and accumulation of the experimental data respectively. Other peripheral devices of the system are magnetic disk units, NAS (Network Attached Storage) device, and a backup tape drive. This is a user's manual of the JT-60 experimental data analysis system. (author)

  4. Operation and Development on the Positive-Ion Based Neutral Beam Injection System for JT-60 and JT-60U

    International Nuclear Information System (INIS)

    Kuriyama, M.; Akino, N.; Ebisawa, N.; Honda, A.; Itoh, T.; Kawai, M.; Mogaki, K.; Ohga, T.; Oohara, H.; Umeda, N.; Usui, K.; Yamamoto, M.; Yamamoto, T.; Matsuoka, M.

    2002-01-01

    The positive-ion based neutral beam injection (NBI) system for JT-60, which consists of 14 beamline units and has a beam energy of 70 to 100 keV, started operation in 1986 with hydrogen beams and injected a neutral beam power of 27 MW at 75 keV into the JT-60 plasma. In 1991, the NBI system was modified to be able to handle deuterium beams as part of the JT-60 upgrade modification. After executing some research and developments, deuterium beams of 40 MW at 95 keV were injected in 1996. As a result, NBI has contributed to the achievement of the highest performance plasmas, a DT-equivalent fusion power gain of 1.25 and a fusion triple product of 1.55 x 10 21 keVs/m 3 , in the world on JT-60U

  5. The design study of the JT-60SU device. No. 3. The superconductor-coils of JT-60SU

    International Nuclear Information System (INIS)

    Ushigusa, Kenkichi; Mori, Katsuharu; Nakagawa, Syouji

    1997-03-01

    The superconducting coil systems and the cryogenic system for the JT-60 Super Upgrade (JT-60SU) has been designed. Both Nb 3 Al and NbTi as a superconducting wire material are employed in the toroidal coils (D-shaped 18 coils) to realize a high field magnet with a low cost. Significant reduction of the coil weight (150 tons/coil) without losing the coil rigidity has been achieved by connecting two toroidal coils with shear panels. Validity of this design is confirmed by the detailed structural analysis and thermohydraulic analysis. The poloidal coil system consists of 4 central solenoid coils with (NbTi) 3 Sn and 6 outer equilibrium field coils with NbTi. This system has an enough capability to supply the flux of 170Vs to produce a 10MA discharge with 200s of flat-top and to make various plasma configurations. The construction procedure of the poloidal coil system is also established under the constraint of the JT-60 site. Two sets of race-track shaped superconducting coils mounted on the top of the machine is designed to compensate the error field inside the vessel by supplying helical (m=2/n=1) magnetic field. By using cryogenic system with a 36kW of cooling capacity, the total cold weight of around 4000tons can be cooled down to 4.5K within one month, and steady heat load of 6.5kW and transient heat load of 9.0MJ can be removed within 30 minutes of discharge repetition rate. (author)

  6. Analysis of 2D Torus and Hub Topologies of 100Mb/s Ethernet for the Whitney Commodity Computing Testbed

    Science.gov (United States)

    Pedretti, Kevin T.; Fineberg, Samuel A.; Kutler, Paul (Technical Monitor)

    1997-01-01

    A variety of different network technologies and topologies are currently being evaluated as part of the Whitney Project. This paper reports on the implementation and performance of a Fast Ethernet network configured in a 4x4 2D torus topology in a testbed cluster of 'commodity' Pentium Pro PCs. Several benchmarks were used for performance evaluation: an MPI point to point message passing benchmark, an MPI collective communication benchmark, and the NAS Parallel Benchmarks version 2.2 (NPB2). Our results show that for point to point communication on an unloaded network, the hub and 1 hop routes on the torus have about the same bandwidth and latency. However, the bandwidth decreases and the latency increases on the torus for each additional route hop. Collective communication benchmarks show that the torus provides roughly four times more aggregate bandwidth and eight times faster MPI barrier synchronizations than a hub based network for 16 processor systems. Finally, the SOAPBOX benchmarks, which simulate real-world CFD applications, generally demonstrated substantially better performance on the torus than on the hub. In the few cases the hub was faster, the difference was negligible. In total, our experimental results lead to the conclusion that for Fast Ethernet networks, the torus topology has better performance and scales better than a hub based network.

  7. QT and JT dispersion and cardiac performance in children with neonatal Bartter syndrome: a pilot study.

    Science.gov (United States)

    Hacihamdioglu, Duygu Ovunc; Fidanci, Kursat; Kilic, Ayhan; Gok, Faysal; Topaloglu, Rezan

    2013-10-01

    QT dispersion and JT dispersion are simple noninvasive arrhythmogenic markers that can be used to assess the homogeneity of cardiac repolarization. The aim of this study was to assess QT and JT dispersion and their relation with left ventricular systolic and diastolic functions in children with Bartter syndrome (BS). Nine neonatal patients with BS (median age 9.7 years) and 20 controls (median age 8 years) were investigated at rest. Both study and control subjects underwent electrocardiography (ECG) in which the interval between two R waves and QT intervals, corrected QT, QT dispersion, corrected QT dispersion, JT, corrected JT, JT dispersion and corrected JT dispersion were measured with 12-lead ECG. Two-dimensional, Doppler echocardiographic examinations were performed. Patients and controls did not differ for gender and for serum levels of potassium, magnesium, and calcium (p > 0.05). Both study and control subjects had normal echocardiographic examination and baseline myocardial performance indexes. The QT dispersion and JT dispersion were significantly prolonged in patients with BS compared to those of the controls {37.5 ms [interquartile range (IQR) 32.5-40] vs. 25.5 ms (IQR 20-30), respectively, p = 0.014 and 37.5 ms (IQR 27.5-40) vs. 22.5 ms (IQR 20-30), respectively, p = 0.003}. Elevated QT and JT dispersion during asymptomatic and normokalemic periods may be risk factors for the development of cardiac complications and arrhythmias in children with BS. In these patients the need for systematic cardiac screening and management protocol is extremely important for effective prevention.

  8. Analysis of ELM stability with extended MHD models in JET, JT-60U and future JT-60SA tokamak plasmas

    Science.gov (United States)

    Aiba, N.; Pamela, S.; Honda, M.; Urano, H.; Giroud, C.; Delabie, E.; Frassinetti, L.; Lupelli, I.; Hayashi, N.; Huijsmans, G.; JET Contributors, the; Research Unit, JT-60SA

    2018-01-01

    The stability with respect to a peeling-ballooning mode (PBM) was investigated numerically with extended MHD simulation codes in JET, JT-60U and future JT-60SA plasmas. The MINERVA-DI code was used to analyze the linear stability, including the effects of rotation and ion diamagnetic drift ({ω }* {{i}}), in JET-ILW and JT-60SA plasmas, and the JOREK code was used to simulate nonlinear dynamics with rotation, viscosity and resistivity in JT-60U plasmas. It was validated quantitatively that the ELM trigger condition in JET-ILW plasmas can be reasonably explained by taking into account both the rotation and {ω }* {{i}} effects in the numerical analysis. When deuterium poloidal rotation is evaluated based on neoclassical theory, an increase in the effective charge of plasma destabilizes the PBM because of an acceleration of rotation and a decrease in {ω }* {{i}}. The difference in the amount of ELM energy loss in JT-60U plasmas rotating in opposite directions was reproduced qualitatively with JOREK. By comparing the ELM affected areas with linear eigenfunctions, it was confirmed that the difference in the linear stability property, due not to the rotation direction but to the plasma density profile, is thought to be responsible for changing the ELM energy loss just after the ELM crash. A predictive study to determine the pedestal profiles in JT-60SA was performed by updating the EPED1 model to include the rotation and {ω }* {{i}} effects in the PBM stability analysis. It was shown that the plasma rotation predicted with the neoclassical toroidal viscosity degrades the pedestal performance by about 10% by destabilizing the PBM, but the pressure pedestal height will be high enough to achieve the target parameters required for the ITER-like shape inductive scenario in JT-60SA.

  9. Capacitated Hub Routing Problem in Hub-and-Feeder Network Design: Modeling and Solution Algorithm

    OpenAIRE

    Gelareh , Shahin; Neamatian Monemi , Rahimeh; Semet , Frédéric

    2015-01-01

    International audience; In this paper, we address the Bounded Cardinality Hub Location Routing with Route Capacity wherein eachhub acts as a transshipment node for one directed route. The number of hubs lies between a minimum anda maximum and the hub-level network is a complete subgraph. The transshipment operations take place atthe hub nodes and flow transfer time from a hub-level transporter to a spoke-level vehicle influences spoketo-hub allocations. We propose a mathematical model and a b...

  10. Low energy, high power injection in JT-60 NBI

    International Nuclear Information System (INIS)

    Mizuno, Makoto; Dairaku, Masayuki; Horiike, Hiroshi

    1988-05-01

    JT-60 neutral beam injector (JT-60 NBI) is designed to inject 20 MW neutral hydrogen beam at energies of 70 ∼ 100 keV and the injection power decreases significantly at low energies (∼40 keV). For the extention of operation region aiming at the low density plasma heating and achieving H-mode by plasma periphery heating, increment of the injection power at low beam energies was required. The single-stage acceleration system was investigated in advance at the Prototype Injector Unit. From this result, the total injection power of 17 MW at 40 keV, 48 A per source was expected at the JT-60 NBI. This system was adopted in the JT-60 NBI from June, 1987 to July, 1987 and 17.6 MW neutral beam injection power was achieved. In the NB heating experiment, the H-mode transition phenomena was observed in JT-60 plasma. (author)

  11. Research and development of JT-60 tokamak

    International Nuclear Information System (INIS)

    Saito, Ryusei; Sato, Hiroshi; Murata, Toshifumi; Ito, Yoshiyasu.

    1978-01-01

    The development of nuclear fusion apparatuses for the purpose of utilizing energy due to nuclear fusion reaction has been forwarded in various countries, and in Japan, the critical plasma testing apparatus JT-60 is about to be constructed, centering around Japan Atomic Energy Research Institute. This is one of four large apparatuses to be constructed in the world, and it is expected to be completed in 1982. JT-60 is a nuclear fusion apparatus of tokamak type aiming at generating critical plasma. The features of JT-60 are the formation of the plasma with small aspect ratio, the equipment of a magnetic limiter, the arrangement of the first wall of molybdenum and high temperature baking as the measures to impurities. The large toroidal magnetic field coil of JT-60 is composed of 18 unit coils. The analyses of magnetic field, thermal behavior and structural strength, the selection of materials, and the development of manufacturing techniques regarding the toroidal coil are described. The vacuum container of JT-60 is composed of the main body of torus type comprising thickwalled rings and bellows, the first wall comprising liners, fixed limiter and magnetic limiter, and observation ports. It is large torus-form container with non-circular cross section, and baking at 500 deg. C is required as the measure to ultrahigh vacuum. Complex forces including electromagnetic force act on it. (Kako, I.)

  12. A four-pellet pneumatic injection system in the JT-60

    International Nuclear Information System (INIS)

    Hiratsuka, Hajime; Kawasaki, Kouzo; Miyo, Yasuhiko; Yoshioka, Yuji; Ohta, Kazuya; Shimizu, Masatsugu; Kondo, Ikuo; Onozuka, Masanori; Shimomura, Tomoyoshi; Iwamoto, Syuichi; Hashiri, Noboru

    1991-01-01

    A four-pellet pneumatic injection system has been developed for plasma fueling of the JT-60. The JT-60 pellet injector is capable of accelerating separately four cylindrical pellets 3.0 mm in diameter x 3.0 mm long for two pellets and 4.0 mm in diameter x 4.0 mm long for the remaining two. The JT-60 pellet injector was installed on the JT-60 tokamak machine at the end of 1988. Obtained pellet velocity was higher than 2300 m/s by propellant gases of up to 100 bar and the pellet fueling efficiency achieved was around 70% for both dimensions of pellets. This paper describes the design, injection operation and performance test results of the JT-60 pellet injector. (orig.)

  13. A four-pellet pneumatic injection system in the JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Hiratsuka, Hajime; Kawasaki, Kouzo; Miyo, Yasuhiko; Yoshioka, Yuji; Ohta, Kazuya; Shimizu, Masatsugu; Kondo, Ikuo (Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan)); Onozuka, Masanori; Shimomura, Tomoyoshi; Iwamoto, Syuichi; Hashiri, Noboru (Mitsubishi Heavy Industries Ltd., Kobe (Japan))

    1991-05-01

    A four-pellet pneumatic injection system has been developed for plasma fueling of the JT-60. The JT-60 pellet injector is capable of accelerating separately four cylindrical pellets 3.0 mm in diameter x 3.0 mm long for two pellets and 4.0 mm in diameter x 4.0 mm long for the remaining two. The JT-60 pellet injector was installed on the JT-60 tokamak machine at the end of 1988. Obtained pellet velocity was higher than 2300 m/s by propellant gases of up to 100 bar and the pellet fueling efficiency achieved was around 70% for both dimensions of pellets. This paper describes the design, injection operation and performance test results of the JT-60 pellet injector. (orig.).

  14. Construction of negative-ion based NBI for JT-60U

    International Nuclear Information System (INIS)

    Kawai, Mikito; Akino, Noboru; Ebisawa, Noboru

    2001-11-01

    The world's first negative-ion based neutral beam injector (N-NBI) system has been developed for studies of non-inductive current drive and plasma core heating with high energy neutral beam injection in higher density plasma. Construction of the N-NBI system for JT-60U was completed in March 1996. The system is composed of a beamline with two ion sources, a set of ion source power supplies, control system and auxiliary sub-system such as cooling water, refrigeration and vacuum system. In July 2001, deuterium neutral beam injection of 400keV and 5.8MW into JT-60U plasma was achieved. In order to increase both beam power and energy we have to go on more improvement of the N-NBI. (author)

  15. How Big is Too Big for Hubs: Marginal Profitability in Hub-and-Spoke Networks

    Science.gov (United States)

    Ross, Leola B.; Schmidt, Stephen J.

    1997-01-01

    Increasing the scale of hub operations at major airports has led to concerns about congestion at excessively large hubs. In this paper, we estimate the marginal cost of adding spokes to an existing hub network. We observe entry/non-entry decisions on potential spokes from existing hubs, and estimate both a variable profit function for providing service in markets using that spoke as well as the fixed costs of providing service to the spoke. We let the fixed costs depend upon the scale of operations at the hub, and find the hub size at which spoke service costs are minimized.

  16. Control of divertor configuration in JT-60

    International Nuclear Information System (INIS)

    Yoshino, R.; Kukuchi, M.; Ninomiya, H.; Yoshida, H.; Tsuji, S.; Hosogane, N.; Seki, S.

    1985-01-01

    The control algorithm of JT-60 divertor configuration is presented. JT-60 has five types of poloidal magnetic field coil with each power supply in order to regulate the control objectives mentioned above. However, if one controls each objective by each coil current independently, there must inevitably occur large interaction between control objectives. Because the relation between control objectives and coil currents is complicated. This situation may be the same with a fusion reactor device. For making it possible to control each objective independently without causing large interaction, the authors adopt the noninteracting control algorithm. Hence, this report demonstrates the availability of this method to the control of JT-60 divertor configuration

  17. Dynamic hubs show competitive and static hubs non-competitive regulation of their interaction partners.

    Directory of Open Access Journals (Sweden)

    Apurv Goel

    Full Text Available Date hub proteins have 1 or 2 interaction interfaces but many interaction partners. This raises the question of whether all partner proteins compete for the interaction interface of the hub or if the cell carefully regulates aspects of this process? Here, we have used real-time rendering of protein interaction networks to analyse the interactions of all the 1 or 2 interface hubs of Saccharomyces cerevisiae during the cell cycle. By integrating previously determined structural and gene expression data, and visually hiding the nodes (proteins and their edges (interactions during their troughs of expression, we predict when interactions of hubs and their partners are likely to exist. This revealed that 20 out of all 36 one- or two- interface hubs in the yeast interactome fell within two main groups. The first was dynamic hubs with static partners, which can be considered as 'competitive hubs'. Their interaction partners will compete for the interaction interface of the hub and the success of any interaction will be dictated by the kinetics of interaction (abundance and affinity and subcellular localisation. The second was static hubs with dynamic partners, which we term 'non-competitive hubs'. Regulatory mechanisms are finely tuned to lessen the presence and/or effects of competition between the interaction partners of the hub. It is possible that these regulatory processes may also be used by the cell for the regulation of other, non-cell cycle processes.

  18. Baking technique of JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Arai, Takashi; Masaki, Kei; Miyachi, Kengo [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    1998-10-01

    It needs to make low ultimate pressure to decrease impurities in a plasma in a nuclear fusion device. Baking technique is very effective method to decrease outgassing rate from first walls and inner surface of the vacuum vessel. However, in such large vacuum vessel, e.g. JT-60, the non-uniform heating and the deformation due to thermal expansion might be very important problems. The baking technique of JT-60 is described. Two baking systems were applied to JT-60 to solve the problem of non-uniform heating. One is a circulation system of the hot nitrogen gas which is located between the inner and outer skins of the double-skin structured vacuum vessel. The other is an electric heater which apply the thick of the vessel. In order to prevent the deformation, the difference of temperature was as small as possible. By both the baking at 300degC and the conditioning such as discharge cleaning, the ultimate pressure was achieved 7.9x10{sup -7} Pa. (author)

  19. Baking technique of JT-60

    International Nuclear Information System (INIS)

    Arai, Takashi; Masaki, Kei; Miyachi, Kengo

    1998-01-01

    It needs to make low ultimate pressure to decrease impurities in a plasma in a nuclear fusion device. Baking technique is very effective method to decrease outgassing rate from first walls and inner surface of the vacuum vessel. However, in such large vacuum vessel, e.g. JT-60, the non-uniform heating and the deformation due to thermal expansion might be very important problems. The baking technique of JT-60 is described. Two baking systems were applied to JT-60 to solve the problem of non-uniform heating. One is a circulation system of the hot nitrogen gas which is located between the inner and outer skins of the double-skin structured vacuum vessel. The other is an electric heater which apply the thick of the vessel. In order to prevent the deformation, the difference of temperature was as small as possible. By both the baking at 300degC and the conditioning such as discharge cleaning, the ultimate pressure was achieved 7.9x10 -7 Pa. (author)

  20. Study of neutral particle behavior and particle confinement in JT-60U

    International Nuclear Information System (INIS)

    Takenaga, Hidenobu; Shimizu, Katsuhiro; Asakura, Nobuyuki; Shimada, Michiya; Kikuchi, Mitsuru; Tsuji-Iio, Shunji; Uchino, Kiichiro; Muraoka, Katsunori.

    1995-07-01

    In order to understand the particle confinement properties in JT-60U, the particle confinement time was estimated through analyses of the neutral particle behavior. First, the neutral particle transport simulation code DEGAS using a Monte-Carlo technique was combined with the simple divertor code for calculating the edge plasma parameters, and was developed to calculate under the experimental conditions in JT-60U. Then, the charged particle source in the main plasma due to the ionization of the neutral particles was evaluated from the analyses of the neutral particle penetration to the main plasma based on results of the simulation code and measurements of D α emission intensities. Finally, the particle confinement time was estimated from the analysis of particle balance. The analyses were performed systematically for the L-mode plasma and H-mode plasma of JT-60U, and a data base of the particle confinement time was obtained. The dependence of the particle confinement time on the plasma parameters and the relationship between the properties of the particle confinement and the energy confinement were examined. (author)

  1. Joint Hub Network Development

    OpenAIRE

    Cruijssen, F.C.A.M.; Borm, P.E.M.; Dullaert, W.; Hamers, H.J.M.

    2007-01-01

    This paper introduces a framework for joint hub network development. Building a joint physical hub for transhipment of goods is expensive and therefore involves considerable risks for the cooperating companies. In a practical setting, it is unlikely that an entire network will be built at once. Rather, the partners will have a more cautious attitude and build the hub facilities one-by-one. In the proposed framework, every time a new hub is introduced, partners will have the opportunity to dec...

  2. Hub and Axis

    OpenAIRE

    Hansen, Gary Alan

    2010-01-01

    The project is for the central building of a community center used by the communities of Blacksburg and Christiansburg. The building is a space configured as a hub that uses axes to determine entering, exiting and vertical movement. The hub configuration of the building is in concentric rings around the atrium in both space and materials. As materials were brought into the building, they enhanced the strong axial configuration and emphasized the layers surrounding the central hub space of ...

  3. Developmental Changes in Brain Network Hub Connectivity in Late Adolescence.

    Science.gov (United States)

    Baker, Simon T E; Lubman, Dan I; Yücel, Murat; Allen, Nicholas B; Whittle, Sarah; Fulcher, Ben D; Zalesky, Andrew; Fornito, Alex

    2015-06-17

    The human brain undergoes substantial development throughout adolescence and into early adulthood. This maturational process is thought to include the refinement of connectivity between putative connectivity hub regions of the brain, which collectively form a dense core that enhances the functional integration of anatomically distributed, and functionally specialized, neural systems. Here, we used longitudinal diffusion magnetic resonance imaging to characterize changes in connectivity between 80 cortical and subcortical anatomical regions over a 2 year period in 31 adolescents between the ages of 15 and 19 years. Connectome-wide analysis indicated that only a small subset of connections showed evidence of statistically significant developmental change over the study period, with 8% and 6% of connections demonstrating decreased and increased structural connectivity, respectively. Nonetheless, these connections linked 93% and 90% of the 80 regions, respectively, pointing to a selective, yet anatomically distributed pattern of developmental changes that involves most of the brain. Hub regions showed a distinct tendency to be highly connected to each other, indicating robust "rich-club" organization. Moreover, connectivity between hubs was disproportionately influenced by development, such that connectivity between subcortical hubs decreased over time, whereas frontal-subcortical and frontal-parietal hub-hub connectivity increased over time. These findings suggest that late adolescence is characterized by selective, yet significant remodeling of hub-hub connectivity, with the topological organization of hubs shifting emphasis from subcortical hubs in favor of an increasingly prominent role for frontal hub regions. Copyright © 2015 the authors 0270-6474/15/359078-10$15.00/0.

  4. Operation and management manual of JT-60 experimental data analysis system

    International Nuclear Information System (INIS)

    Hirayama, Takashi; Morishima, Soichi

    2014-03-01

    In the Japan Atomic Energy Agency Naka Fusion Institute, a lot of experiments have been conducted by using the large tokamak device JT-60 aiming to realize fusion power plant. In order to optimize the JT-60 experiment and to investigate complex characteristics of plasma, JT-60 experimental data analysis system was developed and used for collecting, referring and analyzing the JT-60 experimental data. Main components of the system are a data analysis server and a database server for the analyses and accumulation of the experimental data respectively. Other peripheral devices of the system are magnetic disk units, NAS (Network Attached Storage) device, and a backup tape drive. This is an operation and management manual the JT-60 experimental data analysis system. (author)

  5. Darwin-industrien i højt gear

    DEFF Research Database (Denmark)

    Kjærgaard, Peter C.

    2008-01-01

    Darwin-industrien i højt gear. Næste år bliver et 'Darwin-år' - både tilhængere og kritikere gør sig klar. Udgivelsesdato: 12. december......Darwin-industrien i højt gear. Næste år bliver et 'Darwin-år' - både tilhængere og kritikere gør sig klar. Udgivelsesdato: 12. december...

  6. Assembly study for JT-60SA tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Shibanuma, K., E-mail: shibanuma.kiyoshi@jaea.go.jp [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Arai, T.; Hasegawa, K.; Hoshi, R.; Kamiya, K.; Kawashima, H.; Kubo, H.; Masaki, K.; Saeki, H.; Sakurai, S.; Sakata, S.; Sakasai, A.; Sawai, H.; Shibama, Y.K.; Tsuchiya, K.; Tsukao, N.; Yagyu, J.; Yoshida, K.; Kamada, Y. [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Mizumaki, S. [Toshiba Corporation, Minato-ku, Tokyo 105-8001 (Japan); and others

    2013-10-15

    The assembly scenarios and assembly tools of the major tokamak components for JT-60SA are studied in the following. (1) The assembly frame (with a dedicated 30-tonne crane), which is located around the JT-60SA tokamak, is adopted for effective assembly works in the torus hall and the temporary support of the components during assembly. (2) Metrology for precise positioning of the components is also studied by defining the metrology points on the components. (3) The sector segmentation for weld joints and positioning of the vacuum vessel (VV), the assembly scenario and tools for VV thermal shield (TS), the connection of the outer intercoil structure (OIS) and the installation of the final toroidal field coil (TFC) are studied, as typical examples of the assembly scenarios and tools for JT-60SA.

  7. Gas and LNG trading hubs, hub indexation and destination flexibility in East Asia

    International Nuclear Information System (INIS)

    Shi, Xunpeng; Padinjare Variam, Hari Malamakkavu

    2016-01-01

    In the East Asian gas markets, issues like gas trading hubs, hub indexed pricing, and destination flexibility are being debated. This paper examines the impact of a change in East Asia's pricing benchmark and contract flexibility on the regional and global gas markets. The paper uses the Nexant World Gas Model, a linear program with global cost minimization as the objective. To our knowledge, this study on hub competition, price benchmark change and contract flexibility improvement in East Asia will be the first in the literature and have real policy relevance. The results show that both price benchmark change and contract flexibility improvements will create an overall benefit for the world and East Asia importers, but the impacts are different among exporters and importers. However, there is no evidence of competition among different benchmark hubs and no evidence that destination restrictions cause the “Asia Premium”. It implies that removal of destination clauses has higher priority than the change to hub indexation for Japan, Korea and Chinese Taipei, but both should be treated equally in China. The study also suggests that East Asian importers should cooperate among themselves and with exporters to facilitate the hub creation and contract changes in East Asia. - Highlights: •Gas trading hubs in Japan and China are not mutually exclusive. •Both price benchmark changes and contract flexibility improvements are beneficial. •The “Asian Premium” is not caused by destination restriction. •Destination flexibility is much more important than hub indexation in East Asia except China. •Hub indexation is as important as destination flexibility in China due to pipeline imports.

  8. Coffee Shops, Classrooms and Conversations: public engagement and outreach in a large interdisciplinary research Hub

    Science.gov (United States)

    Holden, Jennifer A.

    2014-05-01

    Public engagement and outreach activities are increasingly using specialist staff for co-ordination, training and support for researchers, they are also becoming expected for large investments. Here, the experience of public engagement and outreach a large, interdisciplinary Research Hub is described. dot.rural, based at the University of Aberdeen UK, is a £11.8 million Research Councils UK Rural Digital Economy Hub, funded as part of the RCUK Digital Economy Theme (2009-2015). Digital Economy research aims to realise the transformational impact of digital technologies on aspects of the environment, community life, cultural experiences, future society, and the economy. The dot.rural Hub involves 92 researchers from 12 different disciplines, including Geography, Hydrology and Ecology. Public Engagement and Outreach is embedded in the dot.rural Digital Economy Hub via an Outreach Officer. Alongside this position, public engagement and outreach activities are compulsory part of PhD student contracts. Public Engagement and Outreach activities at the dot.rural Hub involve individuals and groups in both formal and informal settings organised by dot.rural and other organisations. Activities in the realms of Education, Public Engagement, Traditional and Social Media are determined by a set of Underlying Principles designed for the Hub by the Outreach Officer. The underlying Engagement and Outreach principles match funding agency requirements and expectations alongside researcher demands and the user-led nature of Digital Economy Research. All activities include researchers alongside the Outreach Officer are research informed and embedded into specific projects that form the Hub. Successful public engagement activities have included participation in Café Scientifique series, workshops in primary and secondary schools, and online activities such as I'm a Scientist Get Me Out of Here. From how to engage 8 year olds with making hydrographs more understandable to members of

  9. An algorithm for merging part nodes of JT models exported by FORAN

    Directory of Open Access Journals (Sweden)

    FANG Xiongbing

    2017-05-01

    Full Text Available Many cognominal parts exist in JT models exported by FORAN V70 R2.0 software, and this leads to an increase in time consumption and the space analysis results becoming hard to process when using clearance analysis software to perform distance computing for such JT models. Aiming at this problem, an algorithm for merging component nodes is put forward based on investigating the assembly configuration and inherent information (i.e. geometric and material information of JT models created by FORAN. The method is composed of four steps:coordinate transformation, model node renaming, node geometric data transferring and material attribute processing. Finally, the proposed method is implemented by C++ and JT Open Toolkit. The results show that the new JT models generated by the proposed method are comprised of only one assembly node, and they preserve the intrinsic information of the original JT models. Its validity is illustrated by a great deal of examples, and the content of the worked JT models are reduced by about 7% to 20%.

  10. Data management facility for JT-60

    International Nuclear Information System (INIS)

    Ohasa, K.; Kurimoto, K.; Mochizuki, O.

    1983-01-01

    This study considers the Data Management Facility which is provided for unified management of various diagnostics data with JT-60 experiments. This facility is designed for the purpose of data access. There are about 30 kinds of diagnostic devices that are classified by diagnostic objects equipped for JT-60 facility. It gathers the diagnostic date about 10 Mega Byte per each discharge. Those diagnostic data are varied qualitatively and quantitatively by experimental purpose. Other fundamental information like discharge condition, adjustive value for diagnostic devices is required to process those gathered data

  11. The archives of operational achievements in JT-60

    International Nuclear Information System (INIS)

    Seimiya, Munetaka

    2007-08-01

    Since the first plasma in JT-60 was achieved in April 1985, various experimental challenges have been successfully conducted, and currently producing many new findings. These achievements have been realized by large modifications for lower X-point divertor in 1987, for large plasma current upgrade in 1989-1991, for W-shaped divertor in 1997, and for long pulse discharge in 2002. Such developments contribute to have established JT-60 as the leading tokamak in the world. As a consequence of the 22-year operation, we have accumulated many operational and experimental data. This reports the operational records including troubles and availability, the outline of planning management, the safety control and the promotion procedure of operation in JT-60. (author)

  12. Safety and deterministic failure analyses in high-beta D-D tokamak reactors

    International Nuclear Information System (INIS)

    Selcow, E.C.

    1984-01-01

    Safety and deterministic failure analyses were performed to compare major component failure characteristics for different high-beta D-D tokamak reactors. The primary focus was on evaluating damage to the reactor facility. The analyses also considered potential hazards to the general public and operational personnel. Parametric designs of high-beta D-D tokamak reactors were developed, using WILDCAT as the reference. The size, and toroidal field strength were reduced, and the fusion power increased in an independent manner. These changes were expected to improve the economics of D-D tokamaks. Issues examined using these designs were radiation induced failurs, radiation safety, first wall failure from plasma disruptions, and toroidal field magnet coil failure

  13. Experimental Investigation of Diffuser Hub Injection to Improve Centrifugal Compressor Stability

    Science.gov (United States)

    Skoch, Gary J.

    2004-01-01

    Results from a series of experiments to investigate whether centrifugal compressor stability could be improved by injecting air through the diffuser hub surface are reported. The research was conducted in a 4:1 pressure ratio centrifugal compressor configured with a vane-island diffuser. Injector nozzles were located just upstream of the leading edge of the diffuser vanes. Nozzle orientations were set to produce injected streams angled at 8, 0 and +8 degrees relative to the vane mean camber line. Several injection flow rates were tested using both an external air supply and recirculation from the diffuser exit. Compressor flow range did not improve at any injection flow rate that was tested. Compressor flow range did improve slightly at zero injection due to the flow resistance created by injector openings on the hub surface. Leading edge loading and semi-vaneless space diffusion showed trends similar to those reported earlier from shroud surface experiments that did improve compressor flow range. Opposite trends are seen for hub injection cases where compressor flow range decreased. The hub injection data further explain the range improvement provided by shroud-side injection and suggest that different hub-side techniques may produce range improvement in centrifugal compressors.

  14. Resisting the author: JT LeRoy's fictional authorship

    NARCIS (Netherlands)

    Loontjens, J.

    2008-01-01

    In the last decade, the interest in the relation between author and text, author and autobiography, seems to have grown. In my article, I use the story of the author JT LeRoy as a framework to analyse what this growing interest means for our understanding of the word "author." JT LeRoy’s work was

  15. Design, fabrication and test of double-wall vacuum vessel for JT-60U

    International Nuclear Information System (INIS)

    Uchikawa, Takashi; Ioki, Kimihiro; Ninomiya, Hiromasa.

    1994-01-01

    A double-wall vacuum vessel was designed and fabricated for JT-60U (an upgraded machine of JT-60), which has a plasma current up to 6 MA and a large plasma volume (100 m 3 ). A new concept of Inconel 625 all-welded structure was adopted to the vessel, that comprises an inner plate, square tubes and an outer plate. The vacuum vessel with a multi-arc D-shaped cross section was fabricated by using hot-sizing press. The electromagnetic and structural analysis has been performed for plasma disruption loads. Dynamic responses of the vessel were measured during plasma disruptions, and the observed displacement had a good agreement with the result of FEM analysis. (author)

  16. JT-60 negative ion beam NBI apparatus. Present state of its construction and initial experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Kuriyama, Masaaki [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    1997-02-01

    The NBI (Neutral Beam Injection) apparatus used for negative ion at first in the world, has an aim to actually prove heating and electric current drive with high density plasma at the JT-60 and to constitute physical and technical bases for selection and design of heating apparatus of ITER (International Thermal Nuclear Fusion Experimental Reactor). Construction of 500 KeV negative ion NBI apparatus for the JT-60 started to operate on 1993 was completed at March, 1996. On the way, at a preliminary test on forming and acceleration of the negative ion beam using a portion of this apparatus, 400 KeV and 13.5 A/D of the highest deuterium negative ion beam acceleration in the world was obtained successfully, which gave a bright forecasting of the plasma heating and electric current drive experiment using the negative ion NBI apparatus. After March, 1996, some plans to begin beam incident experiment at the JT-60 using the negative ion NBI apparatus and to execute the heating and electric current drive experiment at the JT-60 under intending increase of beam output are progressed. (G.K.)

  17. Conceptual design of a new supervisory control system for JT-60SA

    International Nuclear Information System (INIS)

    Totsuka, Toshiyuki; Sakata, Shinya

    2009-05-01

    The functions of JT-60 discharge control computer system and the data processing computer system will be integrated into a new JT-60SA supervisory control system to improve the operational efficiency of the JT-60 control computer system. In this report, we first show the necessary requirements for the new JT-60SA supervisory control system that should have high cost performance and maintainability. Next, overall system image of the new JT-60SA supervisory control system is presented and the necessary functions and the issues to be solved in the development are shown. Finally, the necessary manpower for this development and performance of the computer hardware, and the expected reduction of maintenance cost of the computer system are described. (author)

  18. Review of JT-60 experiment (April-June, 1985)

    International Nuclear Information System (INIS)

    1986-11-01

    Initial ohmic heating experiments in JT-60 were performed for a three month period of April-June 1985. A maximum plasma current of 1.6 MA was obtained for both divertor and limiter discharges. Low-q discharges of q eff = 2.5 and high density discharges of 4.8 x 10 19 m -3 were obtained in the divertor configuration. Typical divertor actions, i.e. particle exhaust, heat exhaust, impurity reduction and remote radiative cooling were demonstrated. (author)

  19. Regional Hub port development : the case of Montevideo, Uruguay

    OpenAIRE

    Wilmsmeier, Gordon; Martínez Zarzoso, Inmaculada; Fiess, Norbert

    2011-01-01

    This paper reflects on port development in Uruguay in an environment of trilateral interport competition. The regional characteristics of port development in terms of their geographical, functional and operational characteristics are discussed by analysing the port system’s evolution. The case of Montevideo as the success or failure of a regional hub port development strategy is analysed in detail. Particular attention is given to the evolution and impact of the liner shipping service network...

  20. Heating experiments of JT-60

    International Nuclear Information System (INIS)

    1987-01-01

    In JT-60, after the finish of the first stage Joule experiment, the heating facilities were installed, and the heating experiment was started in August, 1986. As to neutral beam injection, the beam injection experiment at the maximum rating 20 MW carried out, and also as to RF, the injection experiment up to 1.4 MW was carried out in both ion cyclotron and low band hybrid waves. The results worthy of special mention in the heating experiment were the success in the current drive up to 1.7 MA at maximum using low band hybrid waves and the improvement of plasma confinement characteristics obtained by the compound heating of NBI and RF. In this paper, the main results of these heating experiments and their significance are explained. The JT-60 is the testing facilities for attaining the critical plasma condition by additionally heating the plasma which is generated by Joule electric discharge with NBI and RF heatings. The experimental operation cycle of the JT-60 consists of the unit cycle of two weeks, and the number of days in operation is nine days. The temperature of heated plasma rose to 70 million deg C in the 20 MW NBI heating. Hereafter, the improvement of confinement time by increasing the stored energy of plasma is attempted. (Kako, I.)

  1. Solving Hub Network Problem Using Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Mursyid Hasan Basri

    2012-01-01

    Full Text Available This paper addresses a network problem that described as follows. There are n ports that interact, and p of those will be designated as hubs. All hubs are fully interconnected. Each spoke will be allocated to only one of available hubs. Direct connection between two spokes is allowed only if they are allocated to the same hub. The latter is a distinct characteristic that differs it from pure hub-and-spoke system. In case of pure hub-and-spoke system, direct connection between two spokes is not allowed. The problem is where to locate hub ports and to which hub a spoke should be allocated so that total transportation cost is minimum. In the first model, there are some additional aspects are taken into consideration in order to achieve a better representation of the problem. The first, weekly service should be accomplished. Secondly, various vessel types should be considered. The last, a concept of inter-hub discount factor is introduced. Regarding the last aspect, it represents cost reduction factor at hub ports due to economies of scale. In practice, it is common that the cost rate for inter-hub movement is less than the cost rate for movement between hub and origin/destination. In this first model, inter-hub discount factor is assumed independent with amount of flows on inter-hub links (denoted as flow-independent discount policy. The results indicated that the patterns of enlargement of container ship size, to some degree, are similar with those in Kurokawa study. However, with regard to hub locations, the results have not represented the real practice. In the proposed model, unsatisfactory result on hub locations is addressed. One aspect that could possibly be improved to find better hub locations is inter-hub discount factor. Then inter-hub discount factor is assumed to depend on amount of inter-hub flows (denoted as flow-dependent discount policy. There are two discount functions examined in this paper. Both functions are characterized by

  2. Natural Gas Market Hubs

    Data.gov (United States)

    Department of Homeland Security — A hub is a physical transfer point for natural gas where several pipelines are connected. A market center is a hub where the operator offers services that facilitate...

  3. Combined Brayton-JT cycles with refrigerants for natural gas liquefaction

    Science.gov (United States)

    Chang, Ho-Myung; Park, Jae Hoon; Lee, Sanggyu; Choe, Kun Hyung

    2012-06-01

    Thermodynamic cycles for natural gas liquefaction with single-component refrigerants are investigated under a governmental project in Korea, aiming at new processes to meet the requirements on high efficiency, large capacity, and simple equipment. Based upon the optimization theory recently published by the present authors, it is proposed to replace the methane-JT cycle in conventional cascade process with a nitrogen-Brayton cycle. A variety of systems to combine nitrogen-Brayton, ethane-JT and propane-JT cycles are simulated with Aspen HYSYS and quantitatively compared in terms of thermodynamic efficiency, flow rate of refrigerants, and estimated size of heat exchangers. A specific Brayton-JT cycle is suggested with detailed thermodynamic data for further process development. The suggested cycle is expected to be more efficient and simpler than the existing cascade process, while still taking advantage of easy and robust operation with single-component refrigerants.

  4. Discharge optimization in JT-60

    International Nuclear Information System (INIS)

    Ninomiya, H.; Hosogane, N.; Kikuchi, M.; Yoshino, R.; Seki, S.; Kurihara, K.; Kimura, T.; Shimada, R.; Matsukawa, M.

    1986-01-01

    For the optimization of the feedback control gains of the plasma control system in JT-60, the plasma modelling by the regression analysis, the matrix transfer function analysis and the simulation study are performed. The experimental results of plasma control are well consistent with these estimations and the usefulness of a modelling by the regression analysis, the matrix transfer function analysis and the simulation study is experimentally confirmed. It is also shown that the regression analysis is useful for development of the sensor algorithm of plasma shape and location of separatrix line in a feedback control system. Some topics are also presented about plasma engineering obtained in JT-60: possibility to suppress the uncontrollability of plasma density, αI/sub p/ control for plasma position and volt-sec consumption

  5. Permasalahan P-Hub Median Dengan Lintasan Terpendek

    OpenAIRE

    Pasaribu, Raja David

    2013-01-01

    Hub are facilities that serve as sorting, switching, and transhipment in a transportation network. P-hub median problem is a discrete case location allocation problem which all hub is fully connected. In this paper will be intoduced Mixed Integrer Linear Programming (MILP) formulation models of cost for p-hub median problem allocation for uncapacitaced single allocation p-hub median(USApHMP). In this paper also introduced Floyd-Warshall shortest path algorithm to solve p-hub median problems a...

  6. Dynamic design of gas sorption J-T refrigerator

    International Nuclear Information System (INIS)

    Chan, C.K.

    1986-01-01

    A long-life Joule-Thomson refrigerator which is heat powered, involves no sealing, and has few mechanical parts and is desirable for longterm sensor cooling in space. In the gas-sorption J-T refrigerator, cooling is achieved by gas sorption (either adsorption or absorption) processes. Currently, a modular, single-stage refrigerator is being designed and built to be operated at 20 K. The design was analyzed using a dynamic model, which is described here. The model includes the kinetics of the compressors and the heat switches, the heat transfer of the pre-coolers and the heat exchangers, the on/off ratio of the check valves, and the impedance of the J-T valve. The cooling power, the cycle time, and the operating conditions were obtained in terms of the power input, the heat sink temperature, and the J-T impedance

  7. Dynamic design of gas sorption J-T refrigerator

    Science.gov (United States)

    Chan, C. K.

    1986-01-01

    A long-life Joule-Thomson refrigerator which is heat powered, involves no sealing, and has few mechanical parts is desirable for long-term sensor cooling in space. In the gas-sorption J-T refrigerator, cooling is achieved by gas sorption (either adsorption or absorption) processes. Currently, a modular, single-stage refrigerator is being designed and built to be operated at 20 K. The design was analyzed using a dynamic model, which is described here. The model includes the kinetics of the compressors and the heat switches, the heat transfer of the pre-coolers and the heat exchangers, the on/off ratio of the check valves, and the impedance of the J-T valve. The cooling power, the cycle time, and the operating conditions were obtained in terms of the power input, the heat sink temperature, and the J-T impedance.

  8. Present construction status and future plan of JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Iso, Yasuhiko; Yoshikawa, Masaji [Japan Atomic Energy Research Inst., Tokai, Ibaraki. Tokai Research Establishment

    1982-04-01

    As for the critical plasma test facility JT-60, its detailed design was initiated in 1975, and the manufacture of the main body components was started in April, 1978, through the trial manufacture and development of important components. The manufacture of all the system equipment in factories is in progress. Especially, the essential components of main body have been almost completed, and ready to be installed in the building. The building is under construction, and a part of the equipment was brought in and installed since the beginning of 1982 fiscal year. JT-60 is composed of heating system, toroidal magnetic field coil power supply, poloidal magnetic field coil power supply, total control system, associated system for main body and various measuring equipment as well as the main body which consists of vacuum vessel, toroidal and poloidal magnetic field coils, base, primary cooling system, movable limiter and evacuating system. In this report, first the significance of JT-60 development and the outline of JT-60 are described, and the present construction status is reported. The specifications of the essential equipment of the main body and heating system and the measuring system configuration are listed in tables. The aims in JT-60 design are to make plasma generating pulse width longer, to obtain higher beta value in circular cross-section plasma, to install the magnetic limiter, and to realize compound second stage heating.

  9. Using the Contextual Hub Analysis Tool (CHAT) in Cytoscape to Identify Contextually Relevant Network Hubs.

    Science.gov (United States)

    Muetze, Tanja; Lynn, David J

    2017-09-13

    Highly connected nodes in biological networks are called network hubs. Hubs are topologically important to the structure of the network and have been shown to be preferentially associated with a range of phenotypes of interest. The relative importance of a hub node, however, can change depending on the biological context. Here, we provide a step-by-step protocol for using the Contextual Hub Analysis Tool (CHAT), an application within Cytoscape 3, which enables users to easily construct and visualize a network of interactions from a gene or protein list of interest, integrate contextual information, such as gene or protein expression data, and identify hub nodes that are more highly connected to contextual nodes than expected by chance. © 2017 by John Wiley & Sons, Inc. Copyright © 2017 John Wiley & Sons, Inc.

  10. Contextual Hub Analysis Tool (CHAT): A Cytoscape app for identifying contextually relevant hubs in biological networks.

    Science.gov (United States)

    Muetze, Tanja; Goenawan, Ivan H; Wiencko, Heather L; Bernal-Llinares, Manuel; Bryan, Kenneth; Lynn, David J

    2016-01-01

    Highly connected nodes (hubs) in biological networks are topologically important to the structure of the network and have also been shown to be preferentially associated with a range of phenotypes of interest. The relative importance of a hub node, however, can change depending on the biological context. Here, we report a Cytoscape app, the Contextual Hub Analysis Tool (CHAT), which enables users to easily construct and visualize a network of interactions from a gene or protein list of interest, integrate contextual information, such as gene expression or mass spectrometry data, and identify hub nodes that are more highly connected to contextual nodes (e.g. genes or proteins that are differentially expressed) than expected by chance. In a case study, we use CHAT to construct a network of genes that are differentially expressed in Dengue fever, a viral infection. CHAT was used to identify and compare contextual and degree-based hubs in this network. The top 20 degree-based hubs were enriched in pathways related to the cell cycle and cancer, which is likely due to the fact that proteins involved in these processes tend to be highly connected in general. In comparison, the top 20 contextual hubs were enriched in pathways commonly observed in a viral infection including pathways related to the immune response to viral infection. This analysis shows that such contextual hubs are considerably more biologically relevant than degree-based hubs and that analyses which rely on the identification of hubs solely based on their connectivity may be biased towards nodes that are highly connected in general rather than in the specific context of interest. CHAT is available for Cytoscape 3.0+ and can be installed via the Cytoscape App Store ( http://apps.cytoscape.org/apps/chat).

  11. Structure design of the central solenoid in JT-60SA

    International Nuclear Information System (INIS)

    Asakawa, Shuji; Tsuchiya, Katsuhiko; Kuramochi, Masaya; Yoshida, Kiyoshi

    2009-09-01

    The upgrade of JT-60U magnet system to superconducting coils (JT-60SA: JT-60 Super Advanced) has been decided by parties of Japanese government (JA) and European commission (EU) in the framework of the Broader Approach (BA) agreement. The magnet system for JT-60SA consists of a central solenoid (CS), equilibrium field(EF) coils, toroidal field(TF) coils. The central solenoid consists the four winding pack modules. In order to counteract the thermal contraction as well as the electric magnetic repulsion and attraction together with other forces generated in each module, it is necessary to apply pre-loading to the support structure of the solenoid and to pursue a structure which is capable of sustaining such loading. In the present report, the structural design of the supporting structure of the solenoid and the jackets of the modules is verified analytically, and the results indicate that the structural design satisfies the 'Codes for Fusion Facilities - Rules on Superconducting Magnet Structure -'. (author)

  12. Vacuum leak test technique of JT-60

    International Nuclear Information System (INIS)

    Kaminaga, Atsushi; Arai, Takashi; Kodama, Kozo; Sasaki, Noboru; Saidoh, Masahiro

    1998-01-01

    Since a vacuum vessel of JT-60 is very large (167 m 3 ) and is combined with many components, such as magnetic coils, neutral beam injection systems and RF heating systems, etc., the position of leak testing exceeds 700. The two kind of techniques for vacuum leak test used in JT-60 has been described. Firstly the probe helium gas can be fed remotely in the three-dimensionally sectioned 54 regions of the JT-60 torus. The leak test was very rapidly performed by using this method. Secondly the helium detector system has been modified by the additional installation of the cryopump, which reduced the background level of the deuterium gas. The sensitivity of vacuum leak test with the cryopump was two orders of magnitude larger than that of without it. The examples of the performed vacuum leak test are stated. The vacuum leaks during experiments were 9 times. They were caused by thermal strain and plasma discharge. The vacuum leaks just after maintenance are 36 times which mainly caused by mis-installation. (author)

  13. Maximum β limited by ideal MHD ballooning instabilites in JT-60

    International Nuclear Information System (INIS)

    Seki, Shogo; Azumi, Masashi

    1986-03-01

    Maximum β limited by ideal MHD ballooning instabilities is investigated on divertor configurations in JT-60. Maximum β against ballooning modes in JT-60 has strong dependecy on the distribution of the safety factor over the magnetic surfaces. Maximum β is ∼ 2 % for q 0 = 1.0, while more than 3 % for q 0 = 1.5. These results suggest that the profile control of the safety factor, especially on the magnetic axis, is attractive to the higher β operation in JT-60. (author)

  14. Optimal hub location in pipeline networks

    Energy Technology Data Exchange (ETDEWEB)

    Dott, D.R.; Wirasinghe, S.C.; Chakma, A. [Univ. of Calgary, Alberta (Canada)

    1996-12-31

    This paper discusses optimization strategies and techniques for the location of natural gas marketing hubs in the North American gas pipeline network. A hub is a facility at which inbound and outbound network links meet and freight is redirected towards their destinations. Common examples of hubs used in the gas pipeline industry include gas plants, interconnects and market centers. Characteristics of the gas pipeline industry which are relevant to the optimization of transportation costs using hubs are presented. Allocation techniques for solving location-allocation problems are discussed. An outline of the research in process by the authors in the field of optimal gas hub location concludes the paper.

  15. Recent results of JT-60U ICRF antenna operation

    International Nuclear Information System (INIS)

    Fujii, T.; Saigusa, M.; Kimura, H.

    1994-01-01

    Ion cyclotron range of frequencies (ICRF) heating is one of attractive plasma heating methods for reactor grade tokamaks, because it is quite effective in the wide ranges of plasma density and temperature. An antenna which should inject high power into plasma has been developed intensively because the heating efficiency and the coupling properties depend on its design. The antenna was operated at a small antenna-plasma gap in the JT-60 in out of phase mode, which showed the high heating efficiency to obtain high loading resistance, and similarly to other tokamaks. However, in order to reduce heat load to the antenna from plasma, a wide gap is required in reactor grade tokamaks such as ITER, in which the gap is designed to be 0.15 m in CDA. Two new antennas were fabricated for the JT-60U, which were designed to obtain high loading resistance at a wide gap for (π,0) phasing. The JT-60U ICRF heating system is explained. Also the JT-60U antenna is described. Antenna conditioning has been conducted well in the initial operation period. The phasing mode was set at (π,0) phasing, in which high heating efficiency is expected. The procedure is explained. The coupling and radiation loss properties during ICRF heating are reported. The JT-60U ICRF antennas were conditioned quickly with about 70 shots. The maximum coupled power was 6.4 MW for (π,0) phasing, and the power density was 6.1 MW/m 2 . (K.I.)

  16. LOCATING HUBS IN TRANSPORT NETWORKS: AN ARTIFICIAL INTELLIGENCE APPROACH

    OpenAIRE

    Dušan Teodorović; Milica Šelmić; Ivana Vukićević

    2014-01-01

    Hub facilities serve as switching and transshipment points in transportation and communication networks as well as in logistic systems. Hub networks have an influence on flows on the hub-to-hub links and ensure benefit from economies of scale in inter-hub transportation. The key factors for designing a successful hub-and-spoke network are to determine the optimal number of hubs, to properly locate hubs, and to allocate the non-hubs to the hubs. This paper presents the model to determine the l...

  17. Joint Hub Network Development

    NARCIS (Netherlands)

    Cruijssen, F.C.A.M.; Borm, P.E.M.; Dullaert, W.; Hamers, H.J.M.

    2007-01-01

    This paper introduces a framework for joint hub network development. Building a joint physical hub for transhipment of goods is expensive and therefore involves considerable risks for the cooperating companies. In a practical setting, it is unlikely that an entire network will be built at once.

  18. National Geothermal Data System Hub Deployment Timeline (Appendix E-1-d)

    Energy Technology Data Exchange (ETDEWEB)

    Caudill, Christy [Executive Office of the State of Arizona (Arizona Geological Survey)

    2015-12-20

    Excel spreadsheet describing activity, spending, and development for the four data hubs (Arizona Geoloical Survey, Kentucky Geological Survey, Illinois Geological Survey, and Nevada Bureau of Mines and Geology) serving data for the National Geothermal Data System under the State Contributions to the National Geothermal Data System Project.

  19. Southwest Regional Climate Hub and California Subsidiary Hub assessment of climate change vulnerability and adaptation and mitigation strategies

    Science.gov (United States)

    Emile Elias; Caiti Steele; Kris Havstad; Kerri Steenwerth; Jeanne Chambers; Helena Deswood; Amber Kerr; Albert Rango; Mark Schwartz; Peter Stine; Rachel Steele

    2015-01-01

    This report is a joint effort of the Southwest Regional Climate Hub and the California Subsidiary Hub (Sub Hub). The Southwest Regional Climate Hub covers Arizona, California, Hawai‘i and the U.S. affiliated Pacific Islands, Nevada, New Mexico, and Utah and contains vast areas of western rangeland, forests, and high-value specialty crops (Figure 1). The California Sub...

  20. PolarHub: A Global Hub for Polar Data Discovery

    Science.gov (United States)

    Li, W.

    2014-12-01

    This paper reports the outcome of a NSF project in developing a large-scale web crawler PolarHub to discover automatically the distributed polar dataset in the format of OGC web services (OWS) in the cyberspace. PolarHub is a machine robot; its goal is to visit as many webpages as possible to find those containing information about polar OWS, extract this information and store it into the backend data repository. This is a very challenging task given huge data volume of webpages on the Web. Three unique features was introduced in PolarHub to make it distinctive from earlier crawler solutions: (1) a multi-task, multi-user, multi-thread support to the crawling tasks; (2) an extensive use of thread pool and Data Access Object (DAO) design patterns to separate persistent data storage and business logic to achieve high extendibility of the crawler tool; (3) a pattern-matching based customizable crawling algorithm to support discovery of multi-type geospatial web services; and (4) a universal and portable client-server communication mechanism combining a server-push and client pull strategies for enhanced asynchronous processing. A series of experiments were conducted to identify the impact of crawling parameters to the overall system performance. The geographical distribution pattern of all PolarHub identified services is also demonstrated. We expect this work to make a major contribution to the field of geospatial information retrieval and geospatial interoperability, to bridge the gap between data provider and data consumer, and to accelerate polar science by enhancing the accessibility and reusability of adequate polar data.

  1. Experimental Investigation of a Helicopter Rotor Hub Wake

    Science.gov (United States)

    Reich, David; Elbing, Brian; Schmitz, Sven

    2013-11-01

    A scaled model of a notional helicopter rotor hub was tested in the 48'' Garfield Thomas Water Tunnel at the Applied Research Laboratory Penn State. The main objectives of the experiment were to understand the spatial- and temporal content of the unsteady wake downstream of a rotor hub up to a distance corresponding to the empennage. Primary measurements were the total hub drag and velocity measurements at three nominal downstream locations. Various flow structures were identified and linked to geometric features of the hub model. The most prominent structures were two-per-revolution (hub component: scissors) and four-per-revolution (hub component: main hub arms) vortices shed by the hub. Both the two-per-revolution and four-per-revolution structures persisted far downstream of the hub, but the rate of dissipation was greater for the four-per-rev structures. This work provides a dataset for enhanced understanding of the fundamental physics underlying rotor hub flows and serves as validation data for future CFD analyses.

  2. Performance verification tests of JT-60SA CS model coil

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Murakami, Haruyuki [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Chikaraishi, Hirotaka; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Natsume, Kyohei; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2015-11-15

    Highlights: • The performance of the JT-60SA CS model coil was verified. • The CS model coil comprised a quad-pancake wound with a Nb{sub 3}Sn CIC conductor. • The CS model coil met the design requirements. - Abstract: As a final check of the coil manufacturing method of the JT-60 Super Advanced (JT-60SA) central solenoid (CS), we verified the performance of a CS model coil. The model coil comprised a quad-pancake wound with a Nb{sub 3}Sn cable-in-conduit conductor. Measurements of the critical current, joint resistance, pressure drop, and magnetic field were conducted in the verification tests. In the critical-current measurement, the critical current of the model coil coincided with the estimation derived from a strain of −0.62% for the Nb{sub 3}Sn strands. As a result, critical-current degradation caused by the coil manufacturing process was not observed. The results of the performance verification tests indicate that the model coil met the design requirements. Consequently, the manufacturing process of the JT-60SA CS was established.

  3. Hub exchange operations in intermodal hub-and spoke networks: A performance comparison of rail-rail exchange facilities

    OpenAIRE

    Bontekoning, Y.M.

    2006-01-01

    The implementation of hub-and-spoke networks in intermodal transport is suggested as one of the potential solutions for helping to increase the intermodal market share. Traditionally, trains are shunted at hubs; this is a time-consuming process. Since the early 1990s a new type of intermodal terminal, specifically designed for fast tran-shipment at nodes in hub-and-spoke networks, has been introduced in Europe. These hub terminals could replace this time-consuming shunting. Studies on the new...

  4. Temporal network based analysis of cell specific vein graft transcriptome defines key pathways and hub genes in implantation injury.

    Directory of Open Access Journals (Sweden)

    Manoj Bhasin

    Full Text Available Vein graft failure occurs between 1 and 6 months after implantation due to obstructive intimal hyperplasia, related in part to implantation injury. The cell-specific and temporal response of the transcriptome to vein graft implantation injury was determined by transcriptional profiling of laser capture microdissected endothelial cells (EC and medial smooth muscle cells (SMC from canine vein grafts, 2 hours (H to 30 days (D following surgery. Our results demonstrate a robust genomic response beginning at 2 H, peaking at 12-24 H, declining by 7 D, and resolving by 30 D. Gene ontology and pathway analyses of differentially expressed genes indicated that implantation injury affects inflammatory and immune responses, apoptosis, mitosis, and extracellular matrix reorganization in both cell types. Through backpropagation an integrated network was built, starting with genes differentially expressed at 30 D, followed by adding upstream interactive genes from each prior time-point. This identified significant enrichment of IL-6, IL-8, NF-κB, dendritic cell maturation, glucocorticoid receptor, and Triggering Receptor Expressed on Myeloid Cells (TREM-1 signaling, as well as PPARα activation pathways in graft EC and SMC. Interactive network-based analyses identified IL-6, IL-8, IL-1α, and Insulin Receptor (INSR as focus hub genes within these pathways. Real-time PCR was used for the validation of two of these genes: IL-6 and IL-8, in addition to Collagen 11A1 (COL11A1, a cornerstone of the backpropagation. In conclusion, these results establish causality relationships clarifying the pathogenesis of vein graft implantation injury, and identifying novel targets for its prevention.

  5. Comparison of particle confinement in the high confinement mode plasmas with the edge localized mode of the Japan Atomic Energy Research Institute Tokamak-60 Upgrade and the DIII-D tokamak

    International Nuclear Information System (INIS)

    Takenaga, H.; Mahdavi, M.A.; Baker, D.R.

    2001-01-01

    Particle confinement was compared for the high confinement mode plasmas with the edge localized mode in the Japan Atomic Energy Research Institute Tokamak-60 Upgrade (JT-60U) [S. Ishida, JT-60 Team, Nucl. Fusion 39, 1211 (1999)] and the DIII-D tokamak [J. L. Luxon et al., Plasma Physics and Controlled Nuclear Fusion Research 1986 (International Atomic Energy Agency, Vienna, 1987), Vol. 1, p. 159] considering separate confinement times for particles supplied by neutral beam injection (NBI) (center fueling) and by recycling and gas-puffing (edge fueling). Similar dependence on the NBI power was obtained in JT-60U and DIII-D. The particle confinement time for center fueling in DIII-D was smaller by a factor of 4 in the low density discharges and by a factor of 1.8 in the high density discharges than JT-60U scaling, respectively, suggesting the stronger dependence on the density in DIII-D. The particle confinement time for edge fueling in DIII-D was comparable with JT-60U scaling in the low density discharges. However, it decreased to a much smaller value in the high density discharges

  6. Progress in JT-60 joint research

    International Nuclear Information System (INIS)

    Kimura, Haruyuki; Kikuchi, Mitsuru; Inutake, Masaaki

    2007-01-01

    It consists of five chapters; 1) introduction, 2) management system of joint plan and researches, 3) progress of joint researches, 4) results of researches and 5) summary. The second chapter stated the structure of management system of JT-60 joint researches, progress of management of the JT-60 experimental theme system, invitation the public to joint researches and selection of the subjects. The progress of joint researches contained the number of subjects, research members and organizations, change of joint research fields, remote control system of experiments, analysis code group, and number of reports. The main results of researches such as development of operation without center solenoid, Magneto-Hydro-Dynamics (MHD) control by electron cyclotron wave, plasma-wall interaction, application of laser technologies to plasma measurement, and comparison between tokamak and helical are reported. (S.Y.)

  7. Composite hub/metal blade compressor rotor

    Science.gov (United States)

    Yao, S.

    1978-01-01

    A low cost compressor rotor was designed and fabricated for a small jet engine. The rotor hub and blade keepers were compression molded with graphite epoxy. Each pair of metallic blades was held in the hub by a keeper. All keepers were locked in the hub with circumferential windings. Feasibility of fabrication was demonstrated in this program.

  8. Prototype ion source for JT-60 neutral beam injectors

    International Nuclear Information System (INIS)

    Akiba, M.

    1981-01-01

    A prototype ion source for JT-60 neutral beam injectors has been fabricated and tested. Here, we review the construction of the prototype ion source and report the experimental results about the source characteristics that has been obtained at this time. The prototype ion source is now installed at the prototype unit of JT-60 neutral beam injection units and the demonstration of the performances of the ion source and the prototype unit has just started

  9. Results of the H-mode experiments with JT-60 outer and lower divertors

    International Nuclear Information System (INIS)

    Nakamura, Hiroo; Tsuji, Shunji; Nagami, Masayuki

    1989-08-01

    In JT-60, hydrogen H-mode experiments with outer and lower divertors were performed. In the outer divertor, H-mode were obtained, similar to the ones observed in the other lower/upper divertors. Its threshold absorbed power and electron density were 16 MW and 1.8 x 10 19 m -3 . In the two combined heatings with NB+ICRF and NB+LHRF, H-mode discharges are also obtained. Moreover, in new configuration of lower divertor, H-mode phases without and with ELM are obtained. Typical results of the lower divertor are shown to compare the H-mode characteristics between the two configurations. Improvement of the energy confinement time in the two divertors was limited to 10 %. Analyses on ballooning/interchange instabilities were carried out with precise equlibria of JT-60. These results showed that the both modes were enough stable. (author)

  10. JT-60SA power supply system

    International Nuclear Information System (INIS)

    Coletti, A.; Baulaigue, O.; Cara, P.; Coletti, R.; Ferro, A.; Gaio, E.; Matsukawa, M.; Novello, L.; Santinelli, M.; Shimada, K.; Starace, F.; Terakado, T.; Yamauchi, K.

    2011-01-01

    The paper describes the main features of the Superconducting Magnets Power Supply to generate the toroidal and poloidal magnetic fields in JT-60SA tokamak, with special regard to coil current regulation mode and magnets protection.

  11. J.T. van der Kemp and Eighteenth century coded subjectivity | Smit ...

    African Journals Online (AJOL)

    It then proceeds to an analysis of the impact of J.T. van der Kemp, 1799-1804. Theoretically I draw on the distinction between morality and ethics by Michel Foucault as well as his theorising of eighteenth century representational thought. Keywords: J.T. van der Kemp, morality, ethics, models for missionary engagement, ...

  12. Experimental Investigation of a Helicopter Rotor Hub Flow

    Science.gov (United States)

    Reich, David

    The rotor hub system is by far the largest contributor to helicopter parasite drag and a barrier to increasing helicopter forward-flight speed and range. Additionally, the hub sheds undesirable vibration- and instability-inducing unsteady flow over the empennage. The challenges associated with rotor hub flows are discussed, including bluff body drag, interactional aerodynamics, and the effect of the turbulent hub wake on the helicopter empennage. This study was conducted in three phases to quantify model-scale rotor hub flows in water tunnels at The Pennsylvania State University Applied research lab. The first phase investigated scaling and component interaction effects on a 1:17 scale rotor hub model in the 12-inch diameter water tunnel. Effects of Reynolds number, advance ratio, and hub geometry configuration on the drag and wake shed from the rotor hub were quantified using load cell measurements and particle-image velocimetry (PIV). The second phase focused on flow visualization and measurement on a rotor hub and rotor hub/pylon geometry in the 12-inch diameter water tunnel. Stereo PIV was conducted in a cross plane downstream of the hub and flow visualization was conducted using oil paint and fluorescent dye. The third phase concentrated on high accuracy load measurement and prediction up to full-scale Reynolds number on a 1:4.25 scale model in the 48-inch diameter water tunnel. Measurements include 6 degree of freedom loads on the hub and two-component laser-Doppler velocimetry in the wake. Finally, results and conclusions are discussed, followed by recommendations for future investigations.

  13. Design of distributed JT (Joule-Thomson) effect heat exchanger for superfluid 2 K cooling device

    Science.gov (United States)

    Jeong, S.; Park, C.; Kim, K.

    2018-03-01

    Superfluid at 2 K or below is readily obtained from liquid helium at 4.2 K by reducing its vapour pressure. For better cooling performance, however, the cold energy of vaporized helium at 2 K chamber can be effectively utilized in a recuperator which is specially designed in this paper for accomplishing so-called the distributed Joule-Thomson (JT) expansion effect. This paper describes the design methodology of distributed JT effect heat exchanger for 2 K JT cooling device. The newly developed heat exchanger allows continuous significant pressure drop at high-pressure part of the recuperative heat exchanger by using a capillary tube. Being different from conventional recuperative heat exchangers, the efficient JT effect HX must consider the pressure drop effect as well as the heat transfer characteristic. The heat exchanger for the distributed JT effect actively utilizes continuous pressure loss at the hot stream of the heat exchanger by using an OD of 0.64 mm and an ID of 0.4 mm capillary tube. The analysis is performed by dividing the heat exchanger into the multiple sub-units of the heat exchange part and JT valve. For more accurate estimation of the pressure drop of spirally wound capillary tube, preliminary experiments are carried out to investigate the friction factor at high Reynolds number. By using the developed pressure drop correlation and the heat transfer correlation, the specification of the heat exchanger with distributed JT effect for 2 K JT refrigerator is determined.

  14. Recent developments in the JT-60 data processing system

    International Nuclear Information System (INIS)

    Matsuda, T.; Saitoh, N.; Tsugita, T.; Oshima, T.; Sakata, S.; Sato, M.; Koiwa, M.; Watanabe, K.

    1999-01-01

    The JT-60 data processing system was originally a large computer complex system including a lot of micro-computers, several mini-computers, and a mainframe computer. Recently, several improvements have been made to the original system to modernize the system. Many sub-systems composed of aged mini-computers have been replaced with workstations by utilizing recent progress in computer and network technologies. The system can handle ∝300 MB of raw data per discharge, which is three times larger than the amount in the original system. These improvements have been applied to develop element technologies necessary to the remote participation in JT-60 experiments. A remote diagnostics control and monitoring system and a computer system for access to JT-60 data from the Internet are used together with video conferencing systems for a real-time communication. In 1996, the remote participation based on them was successfully demonstrated in collaboration with Japan Atomic Energy Research Institute, Los Alamos National Laboratory, and Princeton Plasma Physics Laboratory. (orig.)

  15. Dynamically Allocated Hub in Task-Evoked Network Predicts the Vulnerable Prefrontal Locus for Contextual Memory Retrieval in Macaques.

    Directory of Open Access Journals (Sweden)

    Takahiro Osada

    2015-06-01

    Full Text Available Neuroimaging and neurophysiology have revealed that multiple areas in the prefrontal cortex (PFC are activated in a specific memory task, but severity of impairment after PFC lesions is largely different depending on which activated area is damaged. The critical relationship between lesion sites and impairments has not yet been given a clear mechanistic explanation. Although recent works proposed that a whole-brain network contains hubs that play integrative roles in cortical information processing, this framework relying on an anatomy-based structural network cannot account for the vulnerable locus for a specific task, lesioning of which would bring impairment. Here, we hypothesized that (i activated PFC areas dynamically form an ordered network centered at a task-specific "functional hub" and (ii the lesion-effective site corresponds to the "functional hub," but not to a task-invariant "structural hub." To test these hypotheses, we conducted functional magnetic resonance imaging experiments in macaques performing a temporal contextual memory task. We found that the activated areas formed a hierarchical hub-centric network based on task-evoked directed connectivity, differently from the anatomical network reflecting axonal projection patterns. Using a novel simulated-lesion method based on support vector machine, we estimated severity of impairment after lesioning of each area, which accorded well with a known dissociation in contextual memory impairment in macaques (impairment after lesioning in area 9/46d, but not in area 8Ad. The predicted severity of impairment was proportional to the network "hubness" of the virtually lesioned area in the task-evoked directed connectivity network, rather than in the anatomical network known from tracer studies. Our results suggest that PFC areas dynamically and cooperatively shape a functional hub-centric network to reallocate the lesion-effective site depending on the cognitive processes, apart from

  16. Study of grounding system of large tokamak device JT-60

    International Nuclear Information System (INIS)

    Arakawa, Kiyotsugu; Shimada, Ryuichi; Kishimoto, Hiroshi; Yabuno, Kohei; Ishigaki, Yukio.

    1982-01-01

    In the critical plasma testing facility JT-60 constructed by the Japan Atomic Energy Research Institute, high voltage, large current is required in an instant. Accordingly, for the protection of human bodies and the equipment, and for realizing the stable operation of the complex, precise control and measurement system, a large scale facility of grounding system is required. In case of the JT-60 experimental facility, the equipments with different functions in separate buildings are connected, therefore, it is an important point to avoid high potential difference between buildings. In the grounding system for the JT-60, a reticulate grounding electrode is laid for each building, and these electrodes are connected with a low impedance metallic duct called grounding trunk line. The power supply cables for various magnetic field coils, control lines and measurement lines are laid in the duct. It is a large problem to grasp quantitatively the effect of a grounding trunk line by analysis. The authors analyzed the phenomenon that large current flows into a grounding system by lightning strike or grounding. The fundamental construction of the grounding system for the JT-60, the condition for the analysis and the result of simulation are reported. (Kako, I.)

  17. Puertos, espacio y globalización: el desarrollo de hubs en México

    Directory of Open Access Journals (Sweden)

    Carlos Daniel Martner Peyrelongue

    2010-01-01

    Full Text Available Los puertos hubs se presentan como el nuevo paradigma de desarrollo del transporte y el comercio marítimo internacional en la globalización. Prácticamente todos los países latinoamericanos anuncian megaproyectos para el desarrollo de puertos hubs en sus litorales, generando grandes expectativas de desarrollo regional, con un débil sustento tanto teórico como empírico. En este sentido, el presente trabajo busca contribuir a la caracterización del modelo de puertos hubs en países periféricos dentro de la economíamundo capitalista, aludiendo, en especial, al caso mexicano. Se trata de aportar elementos de análisis para reconocer, a grandes rasgos, las posibilidades del desarrollo de hubs en los litorales mexicanos, desde la perspectiva de los estudios regionales y la geografía del transporte.

  18. Soft hub for bearingless rotors

    Science.gov (United States)

    Dixon, Peter G. C.

    1991-01-01

    Soft hub concepts which allow the direct replacement of articulated rotor systems by bearingless types without any change in controllability or need for reinforcement to the drive shaft and/or transmission/fuselage attachments of the helicopter were studied. Two concepts were analyzed and confirmed for functional and structural feasibility against a design criteria and specifications established for this effort. Both systems are gimballed about a thrust carrying universal elastomeric bearing. One concept includes a set of composite flexures for drive torque transmittal from the shaft to the rotor, and another set (which is changeable) to impart hub tilting stiffness to the rotor system as required to meet the helicopter application. The second concept uses a composite bellows flexure to drive the rotor and to augment the hub stiffness provided by the elastomeric bearing. Each concept was assessed for weight, drag, ROM cost, and number of parts and compared with the production BO-105 hub.

  19. JT-60SA vacuum vessel manufacturing and assembly

    Energy Technology Data Exchange (ETDEWEB)

    Masaki, Kei, E-mail: masaki.kei@jaea.go.jp [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Shibama, Yusuke K.; Sakurai, Shinji; Shibanuma, Kiyoshi; Sakasai, Akira [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan)

    2012-08-15

    Highlights: Black-Right-Pointing-Pointer The design of the JT-60SA vacuum vessel body was completed with the demonstration of manufacturing procedure by the mock-up fabrication of the 20 Degree-Sign upper half of VV. Black-Right-Pointing-Pointer The actual VV manufacturing has started since November 2009. Black-Right-Pointing-Pointer The first product of the VV 40 Degree-Sign sector was completed in May 2011. Black-Right-Pointing-Pointer A basic VV assembly scenario and procedure were studied to complete the 360 Degree-Sign VV including positioning method and joint welding. - Abstract: The JT-60SA vacuum vessel (VV) has a D-shaped poloidal cross section and a toroidal configuration with 10 Degree-Sign segmented facets. A double wall structure is adopted to ensure high rigidity at operational load and high toroidal one-turn resistance. The material is 316L stainless steel with low cobalt content (<0.05%). The design temperatures of the VV at plasma operation and baking are 50 Degree-Sign C and 200 Degree-Sign C, respectively. In the double wall, boric-acid water is circulated at plasma operation to reduce the nuclear heating of the superconducting magnets. For baking, nitrogen gas is circulated in the double wall after draining of the boric-acid water. The manufacturing of the VV started in November 2009 after a fundamental welding R and D and a trial manufacturing of 20 Degree-Sign upper half mock-up. The manufacturing of the first VV 40 Degree-Sign sector was completed in May 2011. A basic concept and required jigs of the VV assembly were studied. This paper describes the design and manufacturing of the vacuum vessel. A plan of VV assembly in torus hall is also presented.

  20. Improvement of voltage holding capability in the 500 keV negative ion source for JT-60SA.

    Science.gov (United States)

    Tanaka, Y; Hanada, M; Kojima, A; Akino, N; Shimizu, T; Ohshima, K; Inoue, T; Watanabe, K; Taniguchi, M; Kashiwagi, M; Umeda, N; Tobari, H; Grisham, L R

    2010-02-01

    Voltage holding capability of JT-60 negative ion source that has a large electrostatic negative ion accelerator with 45 cm x 1.1 m acceleration grids was experimentally examined and improved to realize 500 keV, 22 A, and 100 s D- ion beams for JT-60 Super Advanced. The gap lengths in the acceleration stages were extended to reduce electric fields in a gap between the large grids and at the corner of the support flanges from the original 4-5 to 3-4 kV/mm. As a result, the voltage holding capability without beam acceleration has been successfully improved from 400 to 500 kV. The pulse duration to hold 500 kV reached 40 s of the power supply limitation.

  1. Conceptual design of JT-60SA cryostat

    International Nuclear Information System (INIS)

    Shibama, Y.K.; Sakurai, S.; Masaki, K.; Sukekawa, A.M.; Kaminaga, A.; Yoshida, K.; Matsukawa, M.

    2007-01-01

    JT-60U modification program to fully superconducting device has been proceeded, namely ''JT-60SA'', toward early realization of fusion energy based on tokamak concept. The design of JT-60SA cryostat is expected to achieve a vacuum thermal insulation for super conducting coils, a bio-shielding boundary and structural gravity support. The cryostat is required to cover JT-60SA tokamak device, which is 15 m of total height and 7 m of radius, but there is geometrical limit due to surrounding devices reutilized. Although the cryostat consists of vessel body and gravity support, and the structural material is low cobalt 304 stainless steel (Co: 2 , and the design of the leaf spring is considered to reduce thermal stress, and to withstand the mechanical loads of plasma disruption and seismic loads. The coolant is 80 K gas helium and both sides of panel are covered with multi-layers super insulation (SI) to reduce heat load (radiation) up to 1/100. Fraction of non-covered region is assumed to be 2% due to many port-joints and supports for the vacuum vessel. Total heat load for inner surface of cryostat (600 m 2 ) is 9kW and the heat load for the port-joints (-300 m 2 ) is assumed up to 9 kW. The operational pressure of the cryostat is required to keep less than 10 -2 Pa and about 100,000 m 2 of structural surfaces is considered for exhaust system specification. Another role of the cryostat is the radiation protection. Biological shielding up to 10 micro-Sv/h (for maintenance acceptance) is required of the cryostat surface after the 10 years operation. Thus the cryostat consists of boron (2 wt%) doped concrete of 220 mm thickness and structural SS304 of total 40 mm thickness. The concrete reduces the air activation (41Ar) in the torus hall by 90% rather than the normal one by the thermal neutron absorption of boron. (orig.)

  2. 26 CFR 31.3406(d)-2 - Payee certification failure.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Payee certification failure. 31.3406(d)-2 Section 31.3406(d)-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED... SOURCE Collection of Income Tax at Source § 31.3406(d)-2 Payee certification failure. (a) Requirement to...

  3. High Mach flow associated with plasma detachment in JT-60U

    International Nuclear Information System (INIS)

    Hatayama, A.; Hoshino, K.; Miyamoto, K.

    2003-01-01

    Recent new results of the high Mach flows associated with plasma detachment are presented on the basis of numerical simulations by a 2-D edge simulation code (the B2-Eirene code) and their comparisons with experiments in JT-60U W-shaped divertor plasma. High Mach flows appear near the ionization front away from the target plate. The plasma static pressure rapidly drops, while the total pressure is kept almost constant near the ionization front, because the ionization front near the X-point is clearly separated from the momentum loss region near the target plate. Redistribution from static to dynamic pressure without a large momentum loss is confirmed to be a possible mechanism of the high Mach flows. It has been also shown that the radial structure of the high Mach flow near the X point away from the target plate has a strong correlation with the DOD (Degree of Detachment) at the target plate. Also, we have made systematic analyses on the high Mach flows for both the 'Open' geometry and the 'W-shaped' geometry of JT-60U in order to clarify the geometric effects on the flows. (author)

  4. Role of low order rational q values on the ITB-events in JT-60U plasmas

    International Nuclear Information System (INIS)

    Neudatchin, S.V.; Takizuka, T.; Hayashi, N.; Shirai, H.; Fujita, T.; Isayama, A.; Kamada, Y.; Koide, Y.; Suzuki, T.

    2003-01-01

    The formation of internal transport barriers (ITBs) near q=2,3 surfaces in normal (NrS) or optimized shear discharges of JT-60U and JET is well known. In reverse shear (RS) JT-60U plasmas, the role of q minimum (q min ) equal to 3, 5, 3, 2, 5, 2 is not obvious for ITB formation. ITB-events (non-local confinement bifurcations inside and around ITB in a ms timescale) are found in various JT-60U NrS and RS plasmas. Under sufficient power, ITB-events are seen at rational and not rational values of q min . The space-time evolution of T e and T i is similar even being strongly varied in space and time, suggesting same mechanism(s) of T e and T i transport. The temporal formation of strong ITB in H-mode under passing of q min =3 (after periodical improvements and degradations via ITB-events with 8ms period) in RS mode with P nbi =8MW is presented. Under smaller power, ITB-events are observed only at rational values of q min . In a weak RS shot with P nbi =4MW, abrupt rise of T e is seen at q min =3.5, while more cases of T i rise are observed. The difference of the T e and T i evolution seen regularly under the low power, suggests decoupling of T e and T i transport. (author)

  5. Role of low order rational q values in the ITB-events in JT-60U plasmas

    International Nuclear Information System (INIS)

    Neudatchin, S.V.

    2002-01-01

    The formation of internal transport barriers (ITBs) near q=2,3 surfaces in normal (NrS) or optimized shear discharges of JT-60U and JET is well known. In reverse shear (RS) JT-60U plasmas, the role of q minimum (q min ) equal to 3.5, 3, 2.5, 2 is not obvious for ITB evolution. ITB-events (non-local confinement bifurcations inside and around ITB in a ms timescale) are found in various JT-60U NrS and RS plasmas. (a) Under sufficient power, ITB-events are seen at rational and not rational values of q min . The space-time evolution of Te and Ti is similar. The temporal creation of stronger ITB in H-mode (after periodical improvements and degradations via ITB-events with 8 ms period) under passing of q min = 3 is presented (P nbi = 8 MW, 1.5 MA / 3.7 T). (b) Under smaller power, the influence of some rational q min is seen clearly for ITB-events on T e . In 1.3MA/3.7T shot with very weak RS (Pnbi = 4 MW), abrupt rise of T e is seen at q min 3:5, while more cases of T i rise are observed. (c) The possible role of MHD-activity as ITB-events trigger (ms time scale correlation in some NrS and RS cases) is under investigation. (author)

  6. Supervised hub-detection for brain connectivity

    DEFF Research Database (Denmark)

    Kasenburg, Niklas; Liptrot, Matthew George; Reislev, Nina Linde

    2016-01-01

    , but can smooth discriminative signals in the population, degrading predictive performance. We present a novel hub-detection optimized for supervised learning that both clusters network nodes based on population level variation in connectivity and also takes the learning problem into account. The found......A structural brain network consists of physical connections between brain regions. Brain network analysis aims to find features associated with a parameter of interest through supervised prediction models such as regression. Unsupervised preprocessing steps like clustering are often applied...... hubs are a low-dimensional representation of the network and are chosen based on predictive performance as features for a linear regression. We apply our method to the problem of finding age-related changes in structural connectivity. We compare our supervised hub-detection (SHD) to an unsupervised hub...

  7. Carbon transport and fuel retention in JT-60U with high temperature operation based on postmortem analysis

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, M., E-mail: yoshida.masafumi@jaea.go.jp [Japan Atomic Energy Agency, Mukoyama 801-1, Naka-shi, Ibaraki-ken 311-0193 (Japan); Tanabe, T.; Adachi, A. [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, 6-10-1 Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan); Hayashi, T.; Nakano, T.; Fukumoto, M.; Yagyu, J.; Miyo, Y.; Masaki, K.; Itami, K. [Japan Atomic Energy Agency, Mukoyama 801-1, Naka-shi, Ibaraki-ken 311-0193 (Japan)

    2013-07-15

    Fuel retention rates and carbon re-deposition rates in the plasma shadowed areas, or tile gaps and remote areas, in JT-60U were measured. The total fuel retention rate in the plasma shadowed areas was more than two times higher than that in the carbon re-deposited layers on the plasma facing surfaces, or the divertor tiles. This is because of lower temperature in the plasma shadowed areas than in the plasma facing surfaces, which leads to high hydrogen saturation concentration, although the amount of the carbon re-deposited on the plasma shadowed areas was only 60% of that on the plasma facing surfaces. The total fuel retention rate in JT-60U, including previously determined for all the plasma facing areas, was evaluated to be 1.3 × 10{sup 20} H + D s{sup −1}, and this retention rate was lower than that in the other devices, due probably to high baking temperature operation in JT-60U. Distributions of the fuel retention and the carbon re-deposition in the whole in-vessel of a large tokamak were determined for the first time in the world.

  8. Carbon transport and fuel retention in JT-60U with high temperature operation based on postmortem analysis

    International Nuclear Information System (INIS)

    Yoshida, M.; Tanabe, T.; Adachi, A.; Hayashi, T.; Nakano, T.; Fukumoto, M.; Yagyu, J.; Miyo, Y.; Masaki, K.; Itami, K.

    2013-01-01

    Fuel retention rates and carbon re-deposition rates in the plasma shadowed areas, or tile gaps and remote areas, in JT-60U were measured. The total fuel retention rate in the plasma shadowed areas was more than two times higher than that in the carbon re-deposited layers on the plasma facing surfaces, or the divertor tiles. This is because of lower temperature in the plasma shadowed areas than in the plasma facing surfaces, which leads to high hydrogen saturation concentration, although the amount of the carbon re-deposited on the plasma shadowed areas was only 60% of that on the plasma facing surfaces. The total fuel retention rate in JT-60U, including previously determined for all the plasma facing areas, was evaluated to be 1.3 × 10 20 H + D s −1 , and this retention rate was lower than that in the other devices, due probably to high baking temperature operation in JT-60U. Distributions of the fuel retention and the carbon re-deposition in the whole in-vessel of a large tokamak were determined for the first time in the world

  9. A patient with familial bone marrow failure and an inversion of chromosome 8.

    Science.gov (United States)

    Buchbinder, David Kyle; Zadeh, Touran; Nugent, Diane

    2011-12-01

    Familial bone marrow failure has been associated with a variety of chromosomal aberrations. Chromosome 8 abnormalities have been described in association with neoplastic and hematologic disorders; however, to our knowledge, inversion of the long arm of chromosome 8 has not been described in the context of familial bone marrow failure. We describe a 9-year-old female with familial bone marrow failure and an inversion of chromosome 8 [inv (8) (q22, q24.3)]. Given the importance of considering the genetic determinants of familial bone marrow failure, the potential role of chromosome 8 abnormalities in the development of marrow failure is discussed.

  10. Capacitated Bounded Cardinality Hub Routing Problem: Model and Solution Algorithm

    OpenAIRE

    Gelareha, Shahin; Monemic, Rahimeh Neamatian; Semetd, Frederic

    2017-01-01

    In this paper, we address the Bounded Cardinality Hub Location Routing with Route Capacity wherein each hub acts as a transshipment node for one directed route. The number of hubs lies between a minimum and a maximum and the hub-level network is a complete subgraph. The transshipment operations take place at the hub nodes and flow transfer time from a hub-level transporter to a spoke-level vehicle influences spoke- to-hub allocations. We propose a mathematical model and a branch-and-cut algor...

  11. Design of the movable limiters for JT-60

    International Nuclear Information System (INIS)

    Takashima, Tetsuo; Yamamoto, Masahiro; Nakamura, Hiroo; Ohkubo, Minoru; Ohta, Mitsuru

    1976-07-01

    Two fast-acting movable rail limiters will be used in JT-60 to suppress skin effect of the plasma current with a large radius. They travel safely through a stroke of about 1 m for 0.1 sec in the build-up phase of plasma current. The movable limiter system consists of a driving mechanism, a vacuum seal, a bearing used at high temperatures in a vacuum, a molybdenum rail limiter weighing 200 kg and its auxiliary members. Many problems are involved in construction of the system because the design specifications exceed the present technology. Described are design of the movable limiter system for JT-60 and problems in the mechanical, electrical and vacuum aspects. (auth.)

  12. Development of upgraded pellet injector for JT-60

    International Nuclear Information System (INIS)

    Onozuka, M.; Shimomura, T.; Tanaka, N.; Iwamoto, S.; Hashiri, N.; Oda, Y.; Minami, M.; Hiratsuka, H.; Kawasaki, K.; Takatsu, H.; Shimizu, M.

    1989-01-01

    The pneumatic 4-shot pellet injector had been in use for JT-60 (JAERI Tokamak-60) contributing to plasma studies in 1988. It could propel the pellets up to 1.6 km/sec at 50 bar propellant gas. In 1989, the new gun assembly has been reinstalled in the upgraded system to provide higher performance and reliability. The supply pressure of the propellant gas is to be raised to 100 bar to obtain higher pellet velocity up to 2.3 km/sec. The device is now in use for JT-60, and is expected to contribute to further plasma studies. In this paper the outline of features and performance of the device is presented. 5 refs., 9 figs

  13. Waveguide circuit for LHRF heating in 'JT-60'

    International Nuclear Information System (INIS)

    Uehara, Kazuya; Saegusa, Mikio; Mizuno, Takenori; Sano, Keigo; Hara, Mitsuru; Oishi, Isamu; Kanai, Takao.

    1985-01-01

    As the heating method for attaining the critical condition in the critical plasma experiment apparatus 'JT-60' in the Japan Atomic Energy Research Institute, in addition to Joule heating, as the second heating method, neutral beam injection heating and high frequency heating have been adopted. For this high frequency heating, several tens to 200 MHz band of ICRF heating, several hundreds MHz to several GHz band of LHRF heating and several tens to 200 GHz band of ECR heating were considered, and in the JT-60, 100 MHz band (ICRF) and 2 GHz band (LHRF) have been adopted. Furukawa Electric Co., Ltd. has engaged in the development and manufacture of the waveguides of transmission system used for this high frequency heating through NEC Corp. This high frequency heating is to heat plasma by injecting high frequency radio waves into plasma proper, and reaches 10 MW for the whole high frequency heating. The system efficiently transmitting the radio waves of large power from a Klystron as a high frequency source to the JT-60 is the transmission system. The outline of the waveguides of the 2 GHz band transmission system and the individual performance of respective waveguides are reported. (Kako, I.)

  14. FEM analysis of hollow hub forming in rolling extrusion process

    Directory of Open Access Journals (Sweden)

    J. Bartnicki

    2014-10-01

    Full Text Available In this paper are presented the results of numerical calculations of rolling extrusion process of a hollow hub. As the flanges manufacturing at both sides of the product is required, in the analyzed process of rolling extrusion, a rear bumper was implemented as additional tool limiting axial metal flow. Numerical calculations of the hub forming process were conducted basing on finite element method, applying software Deform3D and Simufact in conditions of three dimensional state of strain. The obtained satisfactory results show that it is possible to conduct the further research works of experimental character, with the application of a modernized aggregate for the rolling extrusion process PO-2.

  15. THE ROLE OF AUTOMOBILE TRANSPORT IN HUBS SERVICE

    Directory of Open Access Journals (Sweden)

    Kirill Iurievich Bely

    2015-09-01

    Full Text Available Article contains approaches to development and functioning of transport-logistic nodes – hubs – in modern conditions. There is hub classification and examples of them on different transport modes. An important component in providing reliability of hub work is automobile transport.

  16. Parametric thermo-hydraulic analysis of the TF system of JT-60SA during fast discharge

    International Nuclear Information System (INIS)

    Polli, Gian Mario; Lacroix, Benoit; Zani, Louis; Besi Vetrella, Ugo; Cucchiaro, Antonio

    2013-01-01

    Highlights: • We modeled the central clock-wise pancake of JT-60SA TF magnet at the EOB. • We simulated a quench followed by a fast discharge. • We evaluated the temperature and pressure rises in the nominal configuration. • We evaluated the effect of several parameter changes on the thermal-hydraulic response of the system. -- Abstract: The evolution of the conductor temperature and of the helium pressure of the central pancake of the TF superconducting magnet of the JT-60SA tokamak in a quench scenario are here discussed. The quench is triggered by a heat disturbance applied at the end of burning and followed by a fast safety discharge. A parametric study aimed at assessing the robustness of the calculation is also addressed with special regard to the voltage threshold, used to define the occurrence of the quench, and to the time delay, that cover all the possible delays in the fast discharge after quench detection. Finally, due to sensitivity analyses the influences of different parameters were assessed: the material properties of the strands (RRR, copper fraction), the magnitude and the spatial length of the triggering disturbance and the magnetic field distribution. The numerical evaluations were performed in the framework of the Broader Approach Agreement in collaboration with CEA, ENEA and the JT-60SA European Home Team using the 1D code Gandalf [1

  17. 2. Interferometry and polarimetry. 2.3. Polarimetry on JT-60U

    International Nuclear Information System (INIS)

    Kawano, Yasunori

    2000-01-01

    In order to establish an electron density measurement method with high reliability and stability for magnetic-confinement fusion devices, studies on infrared polarimetry have been carried out in JT-60U. Electron density measurement based on tangential Faraday rotation has been verified using a CO 2 laser polarimeter developed for JT-60U. In this article, basic ideas of studies, results from polarimetry experiments, and suggestions for future devices are presented. (author)

  18. Contextual Hub Analysis Tool (CHAT: A Cytoscape app for identifying contextually relevant hubs in biological networks [version 2; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Tanja Muetze

    2016-08-01

    Full Text Available Highly connected nodes (hubs in biological networks are topologically important to the structure of the network and have also been shown to be preferentially associated with a range of phenotypes of interest. The relative importance of a hub node, however, can change depending on the biological context. Here, we report a Cytoscape app, the Contextual Hub Analysis Tool (CHAT, which enables users to easily construct and visualize a network of interactions from a gene or protein list of interest, integrate contextual information, such as gene expression or mass spectrometry data, and identify hub nodes that are more highly connected to contextual nodes (e.g. genes or proteins that are differentially expressed than expected by chance. In a case study, we use CHAT to construct a network of genes that are differentially expressed in Dengue fever, a viral infection. CHAT was used to identify and compare contextual and degree-based hubs in this network. The top 20 degree-based hubs were enriched in pathways related to the cell cycle and cancer, which is likely due to the fact that proteins involved in these processes tend to be highly connected in general. In comparison, the top 20 contextual hubs were enriched in pathways commonly observed in a viral infection including pathways related to the immune response to viral infection. This analysis shows that such contextual hubs are considerably more biologically relevant than degree-based hubs and that analyses which rely on the identification of hubs solely based on their connectivity may be biased towards nodes that are highly connected in general rather than in the specific context of interest.   Availability: CHAT is available for Cytoscape 3.0+ and can be installed via the Cytoscape App Store (http://apps.cytoscape.org/apps/chat.

  19. Development of Europe's gas hubs: Implications for East Asia

    Directory of Open Access Journals (Sweden)

    Xunpeng Shi

    2016-10-01

    Full Text Available Gas trading hubs have been initially developed in the US in 1980s, UK in 1990s, more recently in European in the 2000s and mulled in East Asia now. Due to its freshness and diversification in nationality, governance and culture, the European hub experience can offer valuable lessons for East Asia. This paper seeks to advance understanding of gas hub development in Europe and provide lessons for East Asia. The European experience highlights that market liberalization and transition of gas pricing mechanism are necessary in creating the competitive markets that are needed for functional gas hubs. Political will and regulations further safeguard the competition environment needed for hub development. Natural factors, such as significant domestic production and culture could have a significant impact on the hub development and transition of pricing mechanism. In East Asia, the path to gas trading hubs might be more difficult than in Europe but a growing market creates an opportunity to start new terms with new contracts. Nevertheless, East Asian needs to work hard to development its indigenous gas or LNG trading hubs.

  20. Behaviour of tritium in the vacuum vessel of JT-60U

    International Nuclear Information System (INIS)

    Kobayashi, K.; Miya, N.; Ikeda, Y.; Torikai, Y.; Saito, M.; Alimov, V.

    2015-01-01

    The disassembly of the JT-60U torus started in 2010 after 18 years of deuterium plasma operations. The vessel is made of Inconel 625. Therefore, it was very important to study the hydrogen isotope (particularly tritium) behavior in Inconel 625 from the viewpoint of the clearance procedure. Inconel 625 specimen was exposed to the D 2 (92.8 %) - T 2 (7.2 %) gas mixture at 573 K for 5 hours. The tritium release from the specimen at 298 K was controlled for about 1 year. After that a part of tritium remaining in the specimen was released by heating up to 1073 K. Other part of tritium trapped in the specimen was measured by chemical etching method. Most of the chemical form of the released tritium was HTO. The contaminated specimen by tritium was released continuously the diffusible tritium under the ambient condition. In the tritium release experiment, the amount of desorbed tritium was about 99% during 1 year. It was considered that the tritium in Inconel 625 was released easily

  1. Behaviour of tritium in the vacuum vessel of JT-60U

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, K.; Miya, N.; Ikeda, Y. [JT-60 Safety Assessment Group, JAEA, Mukoyama (Japan); Torikai, Y. [Hydrogen Isotope Research Center, University of Toyama, Gofuku (Japan); Saito, M.; Alimov, V. [ITER Project Management Group, JAEA, Mukoyama (Japan)

    2015-03-15

    The disassembly of the JT-60U torus started in 2010 after 18 years of deuterium plasma operations. The vessel is made of Inconel 625. Therefore, it was very important to study the hydrogen isotope (particularly tritium) behavior in Inconel 625 from the viewpoint of the clearance procedure. Inconel 625 specimen was exposed to the D{sub 2} (92.8 %) - T{sub 2} (7.2 %) gas mixture at 573 K for 5 hours. The tritium release from the specimen at 298 K was controlled for about 1 year. After that a part of tritium remaining in the specimen was released by heating up to 1073 K. Other part of tritium trapped in the specimen was measured by chemical etching method. Most of the chemical form of the released tritium was HTO. The contaminated specimen by tritium was released continuously the diffusible tritium under the ambient condition. In the tritium release experiment, the amount of desorbed tritium was about 99% during 1 year. It was considered that the tritium in Inconel 625 was released easily.

  2. Review of JT-60U experimental results in 1997

    International Nuclear Information System (INIS)

    Adachi, H.; Akasaka, H.; Akino, N.

    1998-08-01

    The JT-60U experiments in 1997 focused mainly on the steady-state tokamak research with the newly installed W-shaped pumped divertor and the negative ion based neutral beam (NNB) in addition to the existing profile and shape control techniques developed in JT-60U. In particular, the research on divertor physics was accelerated under the new divertor system with many of fine diagnostics: Detachment characteristics, pumping control, impurity control, recycling characteristics, etc. in the W-shaped divertor were investigated in detail. The main purpose of confinement and stability studies in 1997 was to improve steadiness of high confinement plasmas with the new divertor. Researches progressed also for the formation conditions of the internal and the surface transport barriers in the high-β p mode, the reversed shear mode and the H-mode. Toward the advanced feedback controls of multiple parameters, the JT-60U started new feedback controls of central line density and divertor neutral gas pressure in addition to the existing controls of off-axis line density, radiation power and neutron production rate. The JT-60U team also carefully studied characteristics of halo current during disruptions. Optimization of NNB operation progressed steadily and injection power increased up to 4.2MW. The NNB-driven current was identified directly from the internal magnetic measurement and driven current profile was confirmed to be consistent with the ACCOME calculation. The current profile control with LHCD successfully sustained the internal transport barrier in reversed shear plasmas. Continuous TAE modes were observed with NNB for the first time as beam-driven TAE modes. (J.P.N.)

  3. Review of JT-60U experimental results in 1997

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, H.; Akasaka, H.; Akino, N. [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

    1998-08-01

    The JT-60U experiments in 1997 focused mainly on the steady-state tokamak research with the newly installed W-shaped pumped divertor and the negative ion based neutral beam (NNB) in addition to the existing profile and shape control techniques developed in JT-60U. In particular, the research on divertor physics was accelerated under the new divertor system with many of fine diagnostics: Detachment characteristics, pumping control, impurity control, recycling characteristics, etc. in the W-shaped divertor were investigated in detail. The main purpose of confinement and stability studies in 1997 was to improve steadiness of high confinement plasmas with the new divertor. Researches progressed also for the formation conditions of the internal and the surface transport barriers in the high-{beta}{sub p} mode, the reversed shear mode and the H-mode. Toward the advanced feedback controls of multiple parameters, the JT-60U started new feedback controls of central line density and divertor neutral gas pressure in addition to the existing controls of off-axis line density, radiation power and neutron production rate. The JT-60U team also carefully studied characteristics of halo current during disruptions. Optimization of NNB operation progressed steadily and injection power increased up to 4.2MW. The NNB-driven current was identified directly from the internal magnetic measurement and driven current profile was confirmed to be consistent with the ACCOME calculation. The current profile control with LHCD successfully sustained the internal transport barrier in reversed shear plasmas. Continuous TAE modes were observed with NNB for the first time as beam-driven TAE modes. (J.P.N.)

  4. Recent results on steady state and confinement improvement research on JT-60U

    International Nuclear Information System (INIS)

    Ide, Shunsuke

    2000-01-01

    On the JT-60U tokamak, fusion plasma research for realization of a steady state tokamak reactor has been pursued. Towards that goal, confinement improved plasmas such as H-mode, high β p , reversed magnetic shear (RS) and latter two combined with H-mode edge pedestal have been developed and investigated intensively. A key issue to achieve non-inductive current drive relevant to a steady state fusion reactor is to increase the fraction of the bootstrap current and match the spatial profile to the optimum. In 1999, as the result of the optimization, the equivalent deuterium-tritium (D-T) fusion gain (Q DT eq ) of 0.5 was sustained for 0.8 s, which is roughly equal to the energy confinement time, in a RS plasma. In order to achieve a RS plasma in steady state two approach have been explored. One is to use external current driver such as lower hybrid current drive (LHCD), and by optimizing LHCD a quasi-steady RS discharge was obtained. The other approach is to utilize bootstrap current as much as possible, and with highly increased fraction of the bootstrap current, a confinement enhancement factor of 3.6 was maintained for 2.7 s in a RS plasma with H-mode edge. A heating and current drive system in the electron cyclotron range of frequency for localized heating and current drive has been installed on JT-60U, and in initial experiments a clear increase of the central electron temperature in a RS high density central region was confirmed only with injected power of 0.75 MW. (author)

  5. Present status of the JT-60 control system

    International Nuclear Information System (INIS)

    Kimura, T.

    1992-01-01

    The present status of the control system for a large fusion device of the JT-60 upgrade tokamak is reported including its original design concept, the progress of the system in the past five-year operation and modification for the upgrade. The control system has the features of hierarchical structure, computer control, adoption of CAMAC interfaces and protective interlock by both software and hard-wired systems. Plant monitoring and control are performed by an efficient data communication via CAMAC highways. Sequential discharge control of is executed by a combination of computers and a timing system. A plasma feedback control system with fast 32-bit microprocessors and a man/machine interface with modern workstations have been newly developed for the operation of the JT-60 upgrade. (author)

  6. Development of multilayer piezoelectric actuator valve for JT-60

    International Nuclear Information System (INIS)

    Miyo, Yasuhiko; Hiratsuka, Hajime; Masui, Hiroshi; Hosogane, Nobuyuki; Miya, Naoyuki

    2001-11-01

    In order to improve the gas injection valve used for the operation of JT-60, a new type of valve (multilayer piezoelectric actuator valve) was developed. The conventional valve (bimorph piezoelectric valve) has been used for 15 years since the beginning of experimental operation in April, 1985. However, it came to be hard to keep the performance of the valve because of the deterioration of the driving source, i.e. piezoelectric element. Developments of the new valve were carried out based on experiences through experimental operations in JT-60. Requirements for the design are: (1) to be hard structure for making a sheet leak, (2) to allow a repair work at atmosphere side without an air vent of the vacuum vessel, (3) to be more smaller and lighter compared with the conventional one, and (4) to have a high maintenance efficiency by utilizing of the commercial piezoelectric elements and power supplies. The newly developed valve was examined with various tests such as gas flow characteristic test, high magnetic field proof test, high temperature proof test and gas flow rate test for aged deterioration. Results, confirm that the performance of the valve is applicable for JT-60 operations. (author)

  7. Virtual Campus Hub technical evaluation report

    DEFF Research Database (Denmark)

    Vercoulen, Frank; Badger, Merete; Monaco, Lucio

    This report describes and discusses the technical achievements of the Virtual Campus Hub project and formulates a brief agenda for the future.......This report describes and discusses the technical achievements of the Virtual Campus Hub project and formulates a brief agenda for the future....

  8. Multiple-Localization and Hub Proteins

    Science.gov (United States)

    Ota, Motonori; Gonja, Hideki; Koike, Ryotaro; Fukuchi, Satoshi

    2016-01-01

    Protein-protein interactions are fundamental for all biological phenomena, and protein-protein interaction networks provide a global view of the interactions. The hub proteins, with many interaction partners, play vital roles in the networks. We investigated the subcellular localizations of proteins in the human network, and found that the ones localized in multiple subcellular compartments, especially the nucleus/cytoplasm proteins (NCP), the cytoplasm/cell membrane proteins (CMP), and the nucleus/cytoplasm/cell membrane proteins (NCMP), tend to be hubs. Examinations of keywords suggested that among NCP, those related to post-translational modifications and transcription functions are the major contributors to the large number of interactions. These types of proteins are characterized by a multi-domain architecture and intrinsic disorder. A survey of the typical hub proteins with prominent numbers of interaction partners in the type revealed that most are either transcription factors or co-regulators involved in signaling pathways. They translocate from the cytoplasm to the nucleus, triggered by the phosphorylation and/or ubiquitination of intrinsically disordered regions. Among CMP and NCMP, the contributors to the numerous interactions are related to either kinase or ubiquitin ligase activity. Many of them reside on the cytoplasmic side of the cell membrane, and act as the upstream regulators of signaling pathways. Overall, these hub proteins function to transfer external signals to the nucleus, through the cell membrane and the cytoplasm. Our analysis suggests that multiple-localization is a crucial concept to characterize groups of hub proteins and their biological functions in cellular information processing. PMID:27285823

  9. Operation experiences of the JT-60 first walls during high-power additional heating experiments

    International Nuclear Information System (INIS)

    Takatsu, H.; Ando, T.; Yamamoto, M.; Arai, T.; Kodama, K.; Suzuki, M.; Shimizu, M.

    1989-01-01

    JT-60 started its operation in May 1985 with TiC-coated molybdenum or Inconel 625 first walls. They provided very clean surfaces as well as superior plasma characteristics during Joule heating discharges. Though 20 μm-thick TiC coatings showed good adhesion characteristics, melting of the TiC coating and also the molybdenum or Inconel 625 substrate was observed at some specific spots, and an influx of heavy metals to the main plasma was inevitable during discharges. Initial results of the additional heating experiments showed degrading effects of locally melted TiC-coated molybdenum or Inconel 625 on plasma operation. Therefore, about a half of the TiC-coated first walls were removed and new graphite first walls were installed during the venting period from April to May 1987. The start-up of the discharge conditioning after installation of a significant number of graphite tiles was very rapid. Flexibility in plasma operation was increased, and JT-60 extended the operation region beyond its original specifications. The graphite first walls of the main chamber performed admirably and maintained their integrity under the conditions of plasma current and additional heating power up to 3.2 MA and 30 MW, respectively. On the other hand, the number of damaged divertor plates was much larger than that expected. The reason of unexpected failure is now under examination. (orig.)

  10. Studies on capillary tube expansion device used in J-T refrigerators operating with nitrogen-hydrocarbon mixtures

    Science.gov (United States)

    Harish Kruthiventi, S. S.; Venkatarathnam, G.

    2017-10-01

    Capillary tube expansion devices are used extensively in small closed cycle J-T refrigerators operating with refrigerant mixtures due to its low cost and the absence of any moving parts. It is possible for J-T refrigerators operating with mixtures that the velocity of refrigerant mixture at capillary tube outlet reaches a value where it equals the speed of sound at certain conditions. The variation of the speed of sound of nitrogen-hydrocarbon mixtures used in J-T refrigerators has been studied in two phase (vapour-liquid) and three-phase (Vapour-liquid-liquid) region as a function of temperature and pressure in this work. Also the conditions under which choking occurs in practical J-T refrigerators is investigated.

  11. Pneumatic pellet injector for JT-60

    International Nuclear Information System (INIS)

    Onozuka, Masanori; Hiratsuka, Hajime; Kawasaki, Kouzo.

    1990-01-01

    The pneumatic 4-shot pellet injector has been installed and operated for JT-60 (JAERI Tokamak-60). The performance tests have proven that the device provides high speed pellets as planned. The maximum pellet velocity obtained in the hydrogen pellet tests is greater than 2.3km/s at 100 bar propellant gas. (author)

  12. Pneumatic pellet injector for JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Onozuka, Masanori (Mitsubishi Heavy Industries Ltd., Tokyo (Japan)); Hiratsuka, Hajime; Kawasaki, Kouzo

    1990-11-01

    The pneumatic 4-shot pellet injector has been installed and operated for JT-60 (JAERI Tokamak-60). The performance tests have proven that the device provides high speed pellets as planned. The maximum pellet velocity obtained in the hydrogen pellet tests is greater than 2.3km/s at 100 bar propellant gas. (author).

  13. [Establishment of a D-galactosamine/lipopolysaccharide induced acute-on-chronic liver failure model in rats].

    Science.gov (United States)

    Liu, Xu-hua; Chen, Yu; Wang, Tai-ling; Lu, Jun; Zhang, Li-jie; Song, Chen-zhao; Zhang, Jing; Duan, Zhong-ping

    2007-10-01

    To establish a practical and reproducible animal model of human acute-on-chronic liver failure for further study of the pathophysiological mechanism of acute-on-chronic liver failure and for drug screening and evaluation in its treatment. Immunological hepatic fibrosis was induced by human serum albumin in Wistar rats. In rats with early-stage cirrhosis (fibrosis stage IV), D-galactosamine and lipopolysaccharide were administered. Mortality and survival time were recorded in 20 rats. Ten rats were sacrificed at 4, 8, and 12 hours. Liver function tests and plasma cytokine levels were measured after D-galactosamine/lipopolysaccharide administration and liver pathology was studied. Cell apoptosis was detected by terminal deoxynucleotidyl transferase-mediated dUTP nick end labeling assay. Most of the rats treated with human albumin developed cirrhosis and fibrosis, and 90% of them died from acute liver failure after administration of D-galactosamine/lipopolysaccharide, with a mean survival time of (16.1+/-3.7) hours. Liver histopathology showed massive or submassive necrosis of the regenerated nodules, while fibrosis septa were intact. Liver function tests were compatible with massive necrosis of hepatocytes. Plasma level of TNFalpha increased significantly, parallel with the degree of the hepatocytes apoptosis. Plasma IL-10 levels increased similarly as seen in patients with acute-on-chronic liver failure. We established an animal model of acute-on-chronic liver failure by treating rats with human serum albumin and later with D-galactosamine and lipopolysaccharide. TNFalpha-mediated liver cell apoptoses plays a very important role in the pathogenesis of acute liver failure.

  14. Injection control development of the JT-60U electron cyclotron heating system

    Energy Technology Data Exchange (ETDEWEB)

    Hiranai, Shinichi; Shinozaki, Shin-ichi; Yokokura, Kenji; Moriyama, Shinichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment; Sato, Fumiaki [Nippon Advanced Technology Co., Ltd., Tokai, Ibaraki (Japan); Suzuki, Yasuo [Atomic Energy General Service Co., Ltd., Tokai, Ibaraki (Japan); Ikeda, Yoshitaka [Japan Atomic Energy Research Inst., Kashiwa, Chiba (Japan)

    2003-03-01

    The JT-60U electron cyclotron heating (ECH) System injects a millimeteric wave at 110 GHz into the JT-60 Plasma, and heats the plasma or drives a current locally to enhance the confinement performance of the JT-60 plasma. The system consists of four sets of high power gyrotrons, high voltage power supplies and transmission lines, and two antennas that launch electron cyclotron (EC) beams toward the plasma. The key features of the injection control system are streering of the direction of the EC beam by driving the movable mirror in the antenna, and capability to set any combination of polarization angle and ellipticity by rotating the two grooved mirrors in the polarizers. This report represents the design, fabrication and improvements of the injection control system. (author)

  15. Review of JT-60U experimental results from March to October, 1991

    International Nuclear Information System (INIS)

    1992-06-01

    Experimental results achieved in the initial operation of JT-60U are described in this paper. Experiments of JT-60U were initiated in March 1991, and deuterium experiments started in the middle of July. Multivariable non-interacting control, H-mode experiments, the high-q and high-β p regime with hot ion enhanced confinement, the divertor heat flux, etc. are reported. Achieved values of the first experiment of the JT-60U LHCD in 1991 were P LH = 1.5 MW, driven current I RF = 2MA, current drive efficiency η CD (=n-bar e R p I RF /P LH ) = 0.25 x 10 20 m -2 A/W and current driven product CDP(=n-bar e R p I RF ) = 3 x 10 20 m -2 MA. (J.P.N.)

  16. Hub location proplems under polyhedral demand uncertainty

    OpenAIRE

    Meraklı, Merve

    2015-01-01

    Cataloged from PDF version of thesis. Includes bibliographical references (leaves 69-74). Thesis (M.S.): Bilkent University, Department of Industrial Engineering, İhsan Doğramacı Bilkent University, 2015. Hubs are points of consolidation and transshipment in many-to-many distribution systems that bene t from economies of scale. In hub location problems, the aim is to locate hub facilities such that each pairwise demand is satis ed and the total cost is minimized. The problem...

  17. Numerical analysis of gas puff modulation experiment on JT-60U

    International Nuclear Information System (INIS)

    Nagashima, Keisuke; Sakasai, Akira

    1992-03-01

    In tokamak transport physics, source modulation experiments are one of the most effective methods. For an analysis of these modulation experiments, a simple numerical method was developed to solve the general transport equations. This method was applied to gas puff modulation experiments on JT-60U. From the comparison between the measured and calculated density perturbations, it was found that the particle diffusion coefficient is about 0.8 m 2 /sec in the edge region and 0.1-0.2 m 2 /sec in the central region. (author)

  18. Competition and coordination in the U.S. airline hub-to-hub markets: An industry pre-merger case study

    Directory of Open Access Journals (Sweden)

    Prasun Bhattacharjee

    2016-04-01

    Full Text Available Purpose: This paper investigates the nature of conduct that existed in the U.S. airline hub-to-hub markets prior to the recent merger wave of the legacy carriers. We explore the strategic importance of network carrier hubs in form of “spheres of influence” on airline market conduct. We also simultaneously recognize the overgrowing role played by Low Cost Carriers (LCC over the years by estimating two conduct parameters - one in markets where LCCs directly compete head-to-head with legacy carriers and the other for markets which LCCs do not serve but has presence in the hub airports or adjacent airports comprising the market endpoints. Thus our supply side framework also sheds some light on the issue of perfect contestability in airline industry. Design/methodology/approach: We estimate a structural oligopoly model for differentiated products with competitive interactions using DB1B data for first quarter of 2004. Findings: Our results imply that the nature of competition is more aggressive relative to Bertrand behavior in hub-to-hub markets and that these markets are less than perfectly contestable. Originality/value: This paper adds to the empirical literature of airline competition by enabling estimation of the actual conduct parameter assuming firm price setting behavior in presence of product differentiation. Contrary to existing literature on airline competition, a structural model enables us to systematically separate out effects of demand, cost and strategic factors on observed airline prices.

  19. The plasma movie database system for JT-60

    International Nuclear Information System (INIS)

    Sueoka, Michiharu; Kawamata, Yoichi; Kurihara, Kenichi; Seki, Akiyuki

    2007-01-01

    The real-time plasma movie with the computer graphics (CG) of plasma shape is one of the most effective methods to know what discharge have been made in the experiment. For an easy use of the movie in the data analysis, we have developed the plasma movie database system (PMDS), which automatically records plasma movie according to the JT-60 discharge sequence, and transfers the movie files on request from the web site. The file is compressed to about 8 MB/shot small enough to be transferred within a few seconds through local area network (LAN). In this report, we describe the developed system from the technical point of view, and discuss a future plan on the basis of advancing video technology

  20. JT-60 database system, 2

    International Nuclear Information System (INIS)

    Itoh, Yasuhiro; Kurihara, Kenichi; Kimura, Toyoaki.

    1987-07-01

    The JT-60 central control system, ''ZENKEI'' collects the control and instrumentation data relevant to discharge and device status data for plant monitoring. The former of the engineering data amounts to about 3 Mbytes per shot of discharge. The ''ZENKEI'' control system which consists of seven minicomputers for on-line real-time control has little performance of handling such a large amount of data for physical and engineering analysis. In order to solve this problem, it was planned to establish the experimental database on the Front-end Processor (FEP) of general purpose large computer in JAERI Computer Center. The database management system (DBMS), therefore, has been developed for creating the database during the shot interval. The engineering data are shipped up from ''ZENKEI'' to FEP through the dedicated communication line after the shot. The hierarchical data model has been adopted in this database, which consists of the data files with tree structure of three keys of system, discharge type and shot number. The JT-60 DBMS provides the data handling packages of subroutines for interfacing the database with user's application programs. The subroutine packages for supporting graphic processing and the function of access control for security of the database are also prepared in this DBMS. (author)

  1. d=8 supergravity

    International Nuclear Information System (INIS)

    Salam, A.; Sezgin, E.

    1984-10-01

    SU(2) gauged N=2 supergravity in d=8 is constructed by generalized dimensional reduction of d=11 supergravity on SU(2) group manifold. The relation between the field equations of the d=8 and those of d=11 supergravities is established. As a byproduct of this, it is shown that certain compactifications of d=11 supergravity give rise to anti-de Sitter space-time (AdS)xS 4 or AdSxCP 2 (with or without SU(2) instanton) or AdSxS 2 xS 2 compactifications of d=8 supergravity. The latter two solutions have no supersymmetry, while AdSxS 4 has N=0 or N=1 supersymmetry. (author)

  2. Determination of slope failure using 2-D resistivity method

    Science.gov (United States)

    Muztaza, Nordiana Mohd; Saad, Rosli; Ismail, Nur Azwin; Bery, Andy Anderson

    2017-07-01

    Landslides and slope failure may give negative economic effects including the cost to repair structures, loss of property value and medical costs in the event of injury. To avoid landslide, slope failure and disturbance of the ecosystem, good and detailed planning must be done when developing hilly area. Slope failure classification and various factors contributing to the instability using 2-D resistivity survey conducted in Selangor, Malaysia are described. The study on landslide and slope failure was conducted at Site A and Site B, Selangor using 2-D resistivity method. The implications of the anticipated ground conditions as well as the field observation of the actual conditions are discussed. Nine 2-D resistivity survey lines were conducted in Site A and six 2-D resistivity survey lines with 5 m minimum electrode spacing using Pole-dipole array were performed in Site B. The data were processed using Res2Dinv and Surfer10 software to evaluate the subsurface characteristics. 2-D resistivity results from both locations show that the study areas consist of two main zones. The first zone is alluvium or highly weathered with the resistivity of 100-1000 Ωm at 20-70 m depth. This zone consists of saturated area (1-100 Ωm) and boulders with resistivity value of 1200-3000 Ωm. The second zone with resistivity values of > 3000 Ωm was interpreted as granitic bedrock. The study area was characterized by saturated zones, highly weathered zone, highly contain of sand and boulders that will trigger slope failure in the survey area. Based on the results obtained from the study findings, it can be concluded that 2-D resistivity method is useful method in determination of slope failure.

  3. Energetic particle physics in JT-60U and JFT-2M

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, K [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Takechi, M [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Ishikawa, M [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Kusama, Y [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Tsuzuki, K [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Urata, K [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Kawashima, H [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Tobita, K [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Fukuyama, A [Department of Nuclear Engineering, Kyoto University, 606-8501, (Japan); Cheng, C Z [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States); Darrow, D S [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States); Kramer, G J [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States); Gorelenkov, N N [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States); Nazikian, R [Princeton Plasma Physics Laboratory, PO Box 451, Princeton, NJ 08543 (United States); Todo, Y [National Institute for Fusion Science, Oroshi-cho, Toki, Gifu, 509-5292, (Japan); Miura, Y [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan); Ozeki, T [Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki, 311-0193 (Japan)

    2004-07-01

    Recent energetic particle physics research in JT-60U and JFT-2M is reported. Alfven eigenmodes (AEs) are investigated in reversed-shear (RS) plasmas in JT-60U where frequency sweeping (FS) modes are observed to follow the q-profile evolution. The RS-induced AE model can explain the FS of the modes within the context of an evolving q-profile. Enhanced energetic ion transport is also investigated with the appearance of modes in the toroidicity-induced AE range of frequency in JT-60U using a multi-channel neutron profile monitor and in JFT-2M using a lost ion probe. Additionally, the ripple loss in the complex toroidal field ripple due to ferritic steel inserts in JFT-2M is shown and compared with model analysis. The simulation code developed to predict ripple loss in JFT-2M will be of use in estimating the heat flux in the complex ripple field of a future device such as ITER.

  4. Divertor pumping system with NBI cryopump for JT-60

    International Nuclear Information System (INIS)

    Akino, Noboru; Kuriyama, Masaaki; Ohga, Tokumichi; Seki, Hiroshi; Tanai, Yutaka

    1998-08-01

    The pumping system for JT-60 W-shape divertor with the NBI cryopump have been developed. The pumping speed achieved in the divertor region was 13-15 m 3 /s for deuterium gas with three units of the NBI cryopumps. In a simulation experiment of helium ash exhaust through the divertor, pumping of a mixed gas of helium and deuterium has been demonstrated using the NBI cryosorption pumps covered with an argon condensed layer. Control of neutral particle pressure in the divertor region became possible by having remodeled an aperture of the existing fast shutter, which is installed between the JT-60 vacuum vessel and NBI beam-line, to be regulated. (author)

  5. Numerical study of hub taper angle on podded propeller performance

    International Nuclear Information System (INIS)

    Islam, M.F.; Veitch, B.; Bose, N.; Liu, P.

    2005-01-01

    Presently, the majority of podded propulsion systems are of the pulling type, because this type provides better hydrodynamic efficiency than the pushing type. There are several possible explanations for the better overall performance of a puller type podded propulsor. One is related to the difference in hub shape. Puller and pusher propellers have opposite hub taper angles, hence different hub and blade root shape. These differences cause changes in the flow condition and possibly influence the overall performance. The current study focuses on the variation in performance of pusher and puller propellers with the same blade sections, but different hub taper angles. A hyperboloidal low order source doublet steady/unsteady time domain panel method code was modified and used to evaluate effects of hub taper angle on the open water propulsive performance of some fixed pitch screw propellers used in podded propulsion systems. The modified code was first validated against measurements of two model propellers in terms of average propulsive performance and good agreement was found. Major findings include significant effects of hub taper angle on propulsive performance of tapered hub propellers and noticeable effects of hub taper angle on sectional pressure distributions of tapered hub propeller blades. (author)

  6. Conceptual design of JT-60SA cryostat

    International Nuclear Information System (INIS)

    Shibama, Y.K.; Sakurai, S.; Masaki, K.; Sukekawa, A.M.; Kaminaga, A.; Sakasai, A.; Matsukawa, M.

    2008-01-01

    This paper describes the conceptual design of cryostat for the JT-60SA, which is a research device for the commercial production of electricity from the controlled fusion reaction in the future. JT-60SA is designed to be a fully superconducting device and cryostat is one of the main components to allow the normal operation. Cryostat covers up the tokamak device, which is 15 m of total height and 7 m of radius, and supports the total weight of 25 MN. Cryostat components consist of vessel body, gravity support and auxiliary systems, such as 80 K thermal shield and vacuum exhaust. The functions required of cryostat are these three, thermal insulation for superconducting magnets, gravity support for the tokamak device, and bio-shielding. The design conditions for each cryostat component are outlined and the features of auxiliary systems such as capacity of vacuum exhaust related to 80 K thermal shield design are summarized

  7. JT-60 configuration parameters for feedback control determined by regression analysis

    Energy Technology Data Exchange (ETDEWEB)

    Matsukawa, Makoto; Hosogane, Nobuyuki; Ninomiya, Hiromasa (Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment)

    1991-12-01

    The stepwise regression procedure was applied to obtain measurement formulas for equilibrium parameters used in the feedback control of JT-60. This procedure automatically selects variables necessary for the measurements, and selects a set of variables which are not likely to be picked up by physical considerations. Regression equations with stable and small multicollinearity were obtained and it was experimentally confirmed that the measurement formulas obtained through this procedure were accurate enough to be applicable to the feedback control of plasma configurations in JT-60. (author).

  8. JT-60 configuration parameters for feedback control determined by regression analysis

    International Nuclear Information System (INIS)

    Matsukawa, Makoto; Hosogane, Nobuyuki; Ninomiya, Hiromasa

    1991-12-01

    The stepwise regression procedure was applied to obtain measurement formulas for equilibrium parameters used in the feedback control of JT-60. This procedure automatically selects variables necessary for the measurements, and selects a set of variables which are not likely to be picked up by physical considerations. Regression equations with stable and small multicollinearity were obtained and it was experimentally confirmed that the measurement formulas obtained through this procedure were accurate enough to be applicable to the feedback control of plasma configurations in JT-60. (author)

  9. Comparison of transient electron heat transport in LHD helical and JT-60U tokamak plasmas

    International Nuclear Information System (INIS)

    Inagaki, S.; Ida, K.; Tamura, N.; Shimozuma, T.; Kubo, S.; Nagayama, Y.; Kawahata, K.; Sudo, S.; Ohkubo, K.; Takenaga, H.; Isayama, A.; Takizuka, T.; Kamada, Y.; Miura, Y.

    2005-01-01

    Transient transport experiments are performed in plasmas with and without Internal Transport Barrier (ITB) on LHD and JT-60U. The dependence of χ e on electron temperature, T e , and electron temperature gradient, ∇T e , is analyzed by an empirical non-linear heat transport model. In plasmas without ITB, two different types of non-linearity of the electron heat transport are observed from cold/heat pulse propagation. The χ e depends on T e and ∇T e in JT-60U, while the ∇T e dependence is weak in LHD. Inside the ITB region, there is no or weak ∇T e dependence both in LHD and JT-60U. A cold pulse growing driven by the negative T e dependence of χ e is observed inside the ITB region (LHD) and near the boundary of the ITB region (JT-60U). (author)

  10. Prazdnik podportshen / Oksana Smirnova, Vladimir Skripov, Vjatsheslav Ivanov...[jt.

    Index Scriptorium Estoniae

    2005-01-01

    Ülevaade diskussioonist Eestis, Lätis ja Leedus presidentide osalemise üle 9. mai pidustustel Moskvas. Juhan Partsi, Villu Reiljani, Toomas Hendrik Ilvese, Marko Mihkelsoni jt. arvamusi. Toimetuse seisukoht

  11. Effect of Vitamin D3 on Asthma Treatment Failures in Adults With Symptomatic Asthma and Lower Vitamin D Levels

    Science.gov (United States)

    Castro, Mario; King, Tonya S.; Kunselman, Susan J.; Cabana, Michael D.; Denlinger, Loren; Holguin, Fernando; Kazani, Shamsah D.; Moore, Wendy C.; Moy, James; Sorkness, Christine A.; Avila, Pedro; Bacharier, Leonard B.; Bleecker, Eugene; Boushey, Homer A.; Chmiel, James; Fitzpatrick, Anne M.; Gentile, Deborah; Hundal, Mandeep; Israel, Elliot; Kraft, Monica; Krishnan, Jerry A.; LaForce, Craig; Lazarus, Stephen C.; Lemanske, Robert; Lugogo, Njira; Martin, Richard J.; Mauger, David T.; Naureckas, Edward; Peters, Stephen P.; Phipatanakul, Wanda; Que, Loretta G.; Sheshadri, Ajay; Smith, Lewis; Solway, Julian; Sullivan-Vedder, Lisa; Sumino, Kaharu; Wechsler, Michael E.; Wenzel, Sally; White, Steven R.; Sutherland, E. Rand

    2014-01-01

    IMPORTANCE In asthma and other diseases, vitamin D insufficiency is associated with adverse outcomes. It is not known if supplementing inhaled corticosteroids with oral vitamin D3 improves outcomes in patients with asthma and vitamin D insufficiency. OBJECTIVE To evaluate if vitamin D supplementation would improve the clinical efficacy of inhaled corticosteroids in patients with symptomatic asthma and lower vitamin D levels. DESIGN, SETTING, AND PARTICIPANTS The VIDA (Vitamin D Add-on Therapy Enhances Corticosteroid Responsiveness in Asthma) randomized, double-blind, parallel, placebo-controlled trial studying adult patients with symptomatic asthma and a serum 25-hydroxyvitamin D level of less than 30 ng/mL was conducted across 9 academic US medical centers in the National Heart, Lung, and Blood Institute’s AsthmaNet network, with enrollment starting in April 2011 and follow-up complete by January 2014. After a run-in period that included treatment with an inhaled corticosteroid, 408 patients were randomized. INTERVENTIONS Oral vitamin D3 (100 000 IU once, then 4000 IU/d for 28 weeks; n = 201) or placebo (n = 207) was added to inhaled ciclesonide (320 µg/d). If asthma control was achieved after 12 weeks, ciclesonide was tapered to 160 µg/d for 8 weeks, then to 80 µg/d for 8 weeks if asthma control was maintained. MAIN OUTCOMES AND MEASURES The primary outcome was time to first asthma treatment failure (a composite outcome of decline in lung function and increases in use of β-agonists, systemic corticosteroids, and health care). RESULTS Treatment with vitamin D3 did not alter the rate of first treatment failure during 28 weeks (28%[95% CI, 21%-34%] with vitamin D3 vs 29% [95% CI, 23%–35%] with placebo; adjusted hazard ratio, 0.9 [95% CI, 0.6–1.3]). Of 14 prespecified secondary outcomes, 9 were analyzed, including asthma exacerbation; of those 9, the only statistically significant outcome was a small difference in the overall dose of ciclesonide required to

  12. Requirements for tokamak remote operation: Application to JT-60SA

    International Nuclear Information System (INIS)

    Innocente, Paolo; Barbato, Paolo; Farthing, Jonathan; Giruzzi, Gerardo; Ide, Shunsuke; Imbeaux, Frédéric; Joffrin, Emmanuel; Kamada, Yutaka; Kühner, Georg; Naito, Osamu; Urano, Hajime; Yoshida, Maiko

    2015-01-01

    Highlights: • We analyzed the data management system (DMS) appropriate for international collaboration. • We define the principal requirements for all components of the DMS. • We evaluated application of DMS requirements to the JT-60SA experiment. • We evaluated the role network bandwidth and time delay between EU and Japan. - Abstract: Remote operation and data analysis are becoming key requirements of any fusion devices. In this framework a well-conceived data management system integrated with a suite of analysis and support tools are essential components for an efficient remote exploitation of any fusion device. The following components must be considered: data archiving data model architecture; remote data and computers access; pulse schedule, data analysis software and support tools; remote control room specifications and security issues. The definition of a device-generic data model plays also important role in improving the ability to share solution and reducing learning time. As for the remote control room, the implementation of an Operation Request Gateway has been identified as an answer to security issues meanwhile remotely proving all the required features to effectively operate a device. Previous requirements have been analyzed for the new JT-60SA tokamak device. Remote exploitation is paramount in the JT-60SA case which is expected to be jointly operated between Japan and Europe. Due to the geographical distance of the two parties an optimal remote operation and remote data-analysis is considered as a key requirement in the development of JT-60SA. It this case the effects of network speed and delay have been also evaluated and tests have confirmed that the performance can vary significantly depending on the technology used.

  13. Requirements for tokamak remote operation: Application to JT-60SA

    Energy Technology Data Exchange (ETDEWEB)

    Innocente, Paolo, E-mail: paolo.innocente@igi.cnr.it [Consorzio RFX, Corso Stati Uniti 4, 35127 Padova (Italy); Barbato, Paolo [Consorzio RFX, Corso Stati Uniti 4, 35127 Padova (Italy); Farthing, Jonathan [CCFE, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Giruzzi, Gerardo [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Ide, Shunsuke [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Imbeaux, Frédéric; Joffrin, Emmanuel [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Kamada, Yutaka [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan); Kühner, Georg [Max-Planck-Institute for Plasma Physics, EURATOM Association, Wendelsteinstr. 1, 17491 Greifswald (Germany); Naito, Osamu; Urano, Hajime; Yoshida, Maiko [Japan Atomic Energy Agency, Naka, Ibaraki-ken 311-0193 (Japan)

    2015-10-15

    Highlights: • We analyzed the data management system (DMS) appropriate for international collaboration. • We define the principal requirements for all components of the DMS. • We evaluated application of DMS requirements to the JT-60SA experiment. • We evaluated the role network bandwidth and time delay between EU and Japan. - Abstract: Remote operation and data analysis are becoming key requirements of any fusion devices. In this framework a well-conceived data management system integrated with a suite of analysis and support tools are essential components for an efficient remote exploitation of any fusion device. The following components must be considered: data archiving data model architecture; remote data and computers access; pulse schedule, data analysis software and support tools; remote control room specifications and security issues. The definition of a device-generic data model plays also important role in improving the ability to share solution and reducing learning time. As for the remote control room, the implementation of an Operation Request Gateway has been identified as an answer to security issues meanwhile remotely proving all the required features to effectively operate a device. Previous requirements have been analyzed for the new JT-60SA tokamak device. Remote exploitation is paramount in the JT-60SA case which is expected to be jointly operated between Japan and Europe. Due to the geographical distance of the two parties an optimal remote operation and remote data-analysis is considered as a key requirement in the development of JT-60SA. It this case the effects of network speed and delay have been also evaluated and tests have confirmed that the performance can vary significantly depending on the technology used.

  14. Flow Structures within a Helicopter Rotor Hub Wake

    Science.gov (United States)

    Elbing, Brian; Reich, David; Schmitz, Sven

    2015-11-01

    A scaled model of a notional helicopter rotor hub was tested in the 48'' Garfield Thomas Water Tunnel at the Applied Research Laboratory Penn State. The measurement suite included total hub drag and wake velocity measurements (LDV, PIV, stereo-PIV) at three downstream locations. The main objective was to understand the spatiotemporal evolution of the unsteady wake between the rotor hub and the nominal location of the empennage (tail). Initial analysis of the data revealed prominent two- and four-per-revolution fluid structures linked to geometric hub features persisting into the wake far-field. In addition, a six-per-revolution fluid structure was observed in the far-field, which is unexpected due to the lack of any hub feature with the corresponding symmetry. This suggests a nonlinear interaction is occurring within the wake to generate these structures. This presentation will provide an overview of the experimental data and analysis with particular emphasis on these six-per-revolution structures.

  15. Investigating for failure of central ventilation fan blade

    International Nuclear Information System (INIS)

    Koo, Jae Raeyang; Ko Woo Sig; Kim, Yeon Hwan; Park, Kwang Ha

    2002-01-01

    During the operation, central ventilation fan stopped when switch 'on' condition. When central ventilation fan disassemble, ten blades of fan fractured. We have searched cause of failure. We had modeling one of the fan blades and analysis with computer programs. Thus we have find that fracture of central ventilation fan blades is alternative stress and vibration at hub. In this paper, we have described cause of failure

  16. Review of JT-60 experiment (March 1986)

    International Nuclear Information System (INIS)

    1986-11-01

    Results of JT-60 experiment with ohmic heating in March 1986 are summarized. A maximum plasma current of 2 MA, an average plasma density of 5.7 x 10 19 m -3 and energy confinement time of 0.4 - 0.5 sec were obtained. Detailed characteristics of ohmic plasmas are discussed. (author)

  17. Impurity and particle recycling reduction by boronization in JT-60U

    International Nuclear Information System (INIS)

    Higashijima, S.; Sugie, T.; Kubo, H.; Tsuji, S.; Shimada, M.; Asakura, N.; Hosogane, N.; Kawano, Y.; Nakamura, H.; Itami, K.; Sakasai, A.; Shimizu, K.; Ando, T.; Saidoh, M.

    1995-01-01

    In JT-60U boronization using decaborane was carried out. Boronization reduced the oxygen impurity in OH discharges and shortened the wall conditioning after the vacuum vessel vent and consequently enabled JT-60U to produce clean plasmas easily except for NB heated plasmas. After boronization, particle recycling was reduced drastically in OH and NB discharges. High confinement plasmas were obtained including high β p mode and H-mode discharges. In the latest boronization part of divertor plates were replaced with B 4 C coated tiles with a B 4 C thickness similar 300 μm. After introducing B 4 C divertor tiles, an explosive generation of boron particles from the tiles was observed. By the combined effects of boronization with decaborane and boron generation from B 4 C tiles, oxygen impurity was so low that oxygen line signals were reduced to noise levels after the latest boronization. On the other hand, boron burst from the B 4 C tiles restricted the operation of JT-60U. ((orig.))

  18. Disruption Studies in JT-60U

    International Nuclear Information System (INIS)

    Kawano, Y.; Yoshino, R.; Neyatani, Y.; Nakamura, Y.; Tokuda, S.; Tamai, H.

    2002-01-01

    Intensive studies on the physics of disruptions and developments of avoidance/mitigation methods of disruption-related phenomena have being carried out in JT-60U. The characteristics of the disruption sequence were well understood from the observation of the relationship between the heat pulse onto divertor plates during thermal quench and the impurity influx into the plasma, which determined the speed of the following current quench. A fast shutdown was first demonstrated by injecting impurity ice pellets to the plasma and intensively reducing the heat flux on first wall. The halo current and its toroidal asymmetry were precisely measured, and the halo current database was made for ITER in a wide parameter range. It was found that TPF x I h /I p0 was 0.52 at the maximum in a large tokamak like the JT-60U, whereas the higher factor of 0.75 had been observed in medium-sized tokamaks such as Alcator C-Mod and ASDEX-Upgrade. The vertical displacement event (VDE) at the start of the current quench was carefully investigated, and the neutral point where the VDE hardly occurs was discovered. MHD simulations clarified the onset mechanisms of the VDE, in which the eddy current effect of the up-down asymmetric resistive shell was essential. The real-time Z j measurement was improved for avoiding VDEs during slow current quench, and plasma-wall interaction was avoided by a well-optimized plasma equilibrium control. Magnetic fluctuations that were spontaneously generated at the disruption and/or enhanced by the externally applied helical field have been shown to avoid the generation of runaway electrons. Numerical analysis clarified an adequate rate of collisionless loss of runaway electrons in turbulent magnetic fields, which was consistent with the avoidance of runaway electron generation by magnetic fluctuations observed in JT-60U. Once generated, runaway electrons were suppressed when the safety factor at the plasma surface was reduced to 3 or 2

  19. JT-60U high performance regimes

    International Nuclear Information System (INIS)

    Ishida, S.

    1999-01-01

    High performance regimes of JT-60U plasmas are presented with an emphasis upon the results from the use of a semi-closed pumped divertor with W-shaped geometry. Plasma performance in transient and quasi steady states has been significantly improved in reversed shear and high- βp regimes. The reversed shear regime elevated an equivalent Q DT eq transiently up to 1.25 (n D (0)τ E T i (0)=8.6x10 20 m-3·s·keV) in a reactor-relevant thermonuclear dominant regime. Long sustainment of enhanced confinement with internal transport barriers (ITBs) with a fully non-inductive current drive in a reversed shear discharge was successfully demonstrated with LH wave injection. Performance sustainment has been extended in the high- bp regime with a high triangularity achieving a long sustainment of plasma conditions equivalent to Q DT eq ∼0.16 (n D (0)τ E T i (0)∼1.4x10 20 m -3 ·s·keV) for ∼4.5 s with a large non-inductive current drive fraction of 60-70% of the plasma current. Thermal and particle transport analyses show significant reduction of thermal and particle diffusivities around ITB resulting in a strong Er shear in the ITB region. The W-shaped divertor is effective for He ash exhaust demonstrating steady exhaust capability of τ He */τ E ∼3-10 in support of ITER. Suppression of neutral back flow and chemical sputtering effect have been observed while MARFE onset density is rather decreased. Negative-ion based neutral beam injection (N-NBI) experiments have created a clear H-mode transition. Enhanced ionization cross- section due to multi-step ionization processes was confirmed as theoretically predicted. A current density profile driven by N-NBI is measured in a good agreement with theoretical prediction. N-NBI induced TAE modes characterized as persistent and bursting oscillations have been observed from a low hot beta of h >∼0.1-0.2% without a significant loss of fast ions. (author)

  20. Logistics hubs: an integration of transport infrastructure

    CSIR Research Space (South Africa)

    Botha, M

    2008-07-01

    Full Text Available " that have jumped on the band wagon pushing for logistics hubs to be established in their regions or within their areas of jurisdiction. The feasibility of a logistics hub is dependent on a number of criteria with access to ideally more than two...

  1. Transaction hubs: can tame energy market communications

    Energy Technology Data Exchange (ETDEWEB)

    Hamilos, C.

    2002-07-01

    The nature and function of transaction hubs is described in view of their growing usefulness as electric industry deregulation takes hold and with it the urgent requirement for trading partners to exchange information quickly and efficiently. The paper stresses the many difficulties involved in communications between trading partners since each partner operates under a different set of business rules, with the result that there are 'language differences' to overcome, not to mention the sheer volume of data that must be handled. To make it all work, companies turn increasingly to products like communication hubs. They are able to overcome the fact that different companies have different systems, different data formats and different business rules, and are able to help companies to package, transmit, receive and process information. The principal advantage of a hub is that no one has to learn anyone else's interface. Everyone can continue to use their own data format and transaction models. The hub supplies the protocols and processing rules needed to work with any of the partners connected to the hub. In order to achieve the level of efficiency and reliability required in a hub, certain design principles must be satisfied. These are : scalability, facilities for load balancing, availability of standard routine services, ability to recognize a process as consisting of various transactions, and a transaction as belonging to a specific process, ability to allow the user to configure expiration times around the business processes according to market rules, facility to easily configure validation rules, ability to handle exceptions, ability to interoperate with many middle-ware products, and to manage work flow in a manner that is transparent to operating personnel.

  2. Study of turbofan engines designed for low energy consumption

    Science.gov (United States)

    Gray, D. E.

    1976-01-01

    The near-term technology improvements which can reduce the fuel consumed in the JT9D, JT8D, and JT3D turbofans in commercial fleet operation through the 1980's are identified. Projected technology advances are identified and evaluated for new turbofans to be developed after 1985. Programs are recommended for developing the necessary technology.

  3. Retention of Hydrogen Isotopes in Divertor Tiles Used in JT-60U

    International Nuclear Information System (INIS)

    Hirohata, Y.; Shibahara, T.; Tanabe, T.; Oya, Y.; Arai, T.; Gotoh, Y.; Masaki, K.; Yagyu, J.; Oyaidzu, M.; Okuno, K.; Nishikawa, M.; Miya, N.

    2005-01-01

    Retention characteristics of deuterium and hydrogen retained in graphite tiles placed in the divertor region of JT-60U were investigated by thermal desorption spectroscopy (TDS). The deuterium retained in the near surface of all graphite tiles was mostly replaced by hydrogen due to exposure to hydrogen plasma at the final stage operations, resulting in main deuterium retention in the deeper region. The dominant species desorbed from the divertor tiles were H 2 , HD, D 2 and CH 4 . The smallest retention of hydrogen isotopes (H+D) was observed in the outer divertor tile which was eroded with maximum of 20 μm depth. The amount of H+D retained in the inner divertor tiles covered by the re-deposited layers increased with the thickness of the re-deposited layers. Hydrogen isotopes concentration ((H+D)/C) in the re-deposited layers was ∼0.02, which was much smaller than those observed in JET and other devices

  4. Modelagem para localização de hubs no transporte de encomendas expressas Modelling for location hubs in the express cargo transport

    Directory of Open Access Journals (Sweden)

    Javier Antonio Timaná Alamo

    2006-12-01

    Full Text Available Na presente pesquisa se propõe um modelo matemático de programação linear com variáveis binárias 0/1, para projetar a configuração de uma rede de distribuição de encomendas expressas, visando minimizar os custos e garantindo um bom nível de serviço. O modelo, que é uma modificação da formulação proposta por O’Kelly, define as posições dos hubs, a alocação deles às demais instalações físicas e a construção de roteiros com apenas uma parada intermediária, o que confere mais agilidade ao atendimento da demanda de transporte de carga. Considera-se a instalação de um único hub maior (Hub Principal, que serve como ponto de transbordo para os fluxos de carga entre as distintas regiões de um território, e um conjunto de terminais regionais (mini-hubs, servindo como ponto de conexão, unicamente, para os fluxos de carga existentes em um determinado raio de cobertura. Foram propostas extensões que incluem uma restrição da capacidade operacional do Hub Principal, para evitar seu congestionamento, e duas diferentes estratégias de induzir o aumento de fluxo de carga manipulado pelos mini-hubs. O modelo proposto e suas extensões foram aplicados ao estudo de um caso real, obtendo-se resultados consistentes e uma redução significativa no custo total da rede de distribuição da empresa analisada.This study proposes a mathematical model of linear programming with binary variables 0/1 to project the configuration of a distribution network for express cargo which aims to minimize costs and guarantee a high level of service. The model, which is a modification of the formulation proposed by O’Kelly, defines the position of the hubs, their allocation regarding the other physical installations, and the building of itineraries with only one intermediate stop, which increases agility in meeting the demand of cargo transport. It assumes the installation of a single, major hub (Main Hub, which serves as the transfer point for

  5. Beta cell 5'-shifted isomiRs are candidate regulatory hubs in type 2 diabetes.

    Directory of Open Access Journals (Sweden)

    Jeanette Baran-Gale

    Full Text Available Next-generation deep sequencing of small RNAs has unveiled the complexity of the microRNA (miRNA transcriptome, which is in large part due to the diversity of miRNA sequence variants ("isomiRs". Changes to a miRNA's seed sequence (nucleotides 2-8, including shifted start positions, can redirect targeting to a dramatically different set of RNAs and alter biological function. We performed deep sequencing of small RNA from mouse insulinoma (MIN6 cells (widely used as a surrogate for the study of pancreatic beta cells and developed a bioinformatic analysis pipeline to profile isomiR diversity. Additionally, we applied the pipeline to recently published small RNA-seq data from primary human beta cells and whole islets and compared the miRNA profiles with that of MIN6. We found that: (1 the miRNA expression profile in MIN6 cells is highly correlated with those of primary human beta cells and whole islets; (2 miRNA loci can generate multiple highly expressed isomiRs with different 5'-start positions (5'-isomiRs; (3 isomiRs with shifted start positions (5'-shifted isomiRs are highly expressed, and can be as abundant as their unshifted counterparts (5'-reference miRNAs. Finally, we identified 10 beta cell miRNA families as candidate regulatory hubs in a type 2 diabetes (T2D gene network. The most significant candidate hub was miR-29, which we demonstrated regulates the mRNA levels of several genes critical to beta cell function and implicated in T2D. Three of the candidate miRNA hubs were novel 5'-shifted isomiRs: miR-375+1, miR-375-1 and miR-183-5p+1. We showed by in silico target prediction and in vitro transfection studies that both miR-375+1 and miR-375-1 are likely to target an overlapping, but distinct suite of beta cell genes compared to canonical miR-375. In summary, this study characterizes the isomiR profile in beta cells for the first time, and also highlights the potential functional relevance of 5'-shifted isomiRs to T2D.

  6. An Endosymbiotic Evolutionary Algorithm for the Hub Location-Routing Problem

    Directory of Open Access Journals (Sweden)

    Ji Ung Sun

    2015-01-01

    Full Text Available We consider a capacitated hub location-routing problem (HLRP which combines the hub location problem and multihub vehicle routing decisions. The HLRP not only determines the locations of the capacitated p-hubs within a set of potential hubs but also deals with the routes of the vehicles to meet the demands of customers. This problem is formulated as a 0-1 mixed integer programming model with the objective of the minimum total cost including routing cost, fixed hub cost, and fixed vehicle cost. As the HLRP has impractically demanding for the large sized problems, we develop a solution method based on the endosymbiotic evolutionary algorithm (EEA which solves hub location and vehicle routing problem simultaneously. The performance of the proposed algorithm is examined through a comparative study. The experimental results show that the proposed EEA can be a viable solution method for the supply chain network planning.

  7. Learning Graphical Models With Hubs.

    Science.gov (United States)

    Tan, Kean Ming; London, Palma; Mohan, Karthik; Lee, Su-In; Fazel, Maryam; Witten, Daniela

    2014-10-01

    We consider the problem of learning a high-dimensional graphical model in which there are a few hub nodes that are densely-connected to many other nodes. Many authors have studied the use of an ℓ 1 penalty in order to learn a sparse graph in the high-dimensional setting. However, the ℓ 1 penalty implicitly assumes that each edge is equally likely and independent of all other edges. We propose a general framework to accommodate more realistic networks with hub nodes, using a convex formulation that involves a row-column overlap norm penalty. We apply this general framework to three widely-used probabilistic graphical models: the Gaussian graphical model, the covariance graph model, and the binary Ising model. An alternating direction method of multipliers algorithm is used to solve the corresponding convex optimization problems. On synthetic data, we demonstrate that our proposed framework outperforms competitors that do not explicitly model hub nodes. We illustrate our proposal on a webpage data set and a gene expression data set.

  8. Lean GHTorrent : GitHub data on demand

    NARCIS (Netherlands)

    Gousios, G.; Vasilescu, B.N.; Serebrenik, A.; Zaidman, A.

    2014-01-01

    In recent years, GitHub has become the largest code host in the world, with more than 5M developers collaborating across 10M repositories. Numerous popular open source projects (such as Ruby on Rails, Homebrew, Bootstrap, Django or jQuery) have chosen GitHub as their host and have migrated their

  9. Identification of promising Twin Hub networks : Report of Work Package 1 of the Intermodal rail freight Twin hub Network Northwest Europe - project (final report)

    NARCIS (Netherlands)

    Kreutzberger, E.D.; Konings, J.W.; Meijer, S.; Witteveen, C.; Meijers, B.M.; Pekin, E.; Macharis, C.; Kiel, J.; Kawabata, Y.; Vos, W.

    2014-01-01

    This report is the first deliverable of the project Intermodal Rail Freight Twin Hub Network Northwest Europe. We call its subject Twin hub network and the organisational entity to carry out the actions the Twin hub project. The project is funded by INTERREG NWE (programme IVb). Its work started in

  10. Overview of JT-60U results toward high integrated performance in reactor-relevant regime

    International Nuclear Information System (INIS)

    Fujita, T.

    2002-01-01

    Toward steady sustainment of high integrated performance, we have developed weak magnetic shear (high β p mode) and reversed magnetic shear plasmas. As a large-sized tokamak equipped with a variety of devices for heating, current drive and profile/shape control, JT-60U has high ability to approach the conditions required in reactors: low values of normalized Larmor radius and collisionality, high temperatures with T e > or approx. T i , etc. This paper reviews recent JT-60U results with the emphasis on the projection to the reactor-relevant regime. Full non-inductive current drive has been achieved in a 1.8 MA high β p H-mode plasma with β N 2:4, HH y2 =1.2 and high fusion triple product (3 x 10 20 m -3 keVs) owing to increased N-NB power. In a reversed shear plasma, HH y2 =1.4 at n e /n GW 0.8 under the full non-inductive current drive has been achieved with injection of LHRF and N-NB. In box-type ITBs with reversed shear, barriers for ions and electrons were sustained in a regime with T e > or approx. T i . The pedestal pressure was doubled with increased total poloidal beta in pellet-injected high triangularity plasmas with type I and II ELMs. Stable existence of current hole was demonstrated. (author)

  11. Location of Urban Logistic Terminals as Hub Location Problem

    Directory of Open Access Journals (Sweden)

    Jasmina Pašagić Škrinjar

    2012-09-01

    Full Text Available In this paper the problems of locating urban logistic terminals are studied as hub location problems that due to a large number of potential nodes in big cities belong to hard non-polynomial problems, the so-called NP-problems. The hub location problems have found wide application in physical planning of transport and telecommunication systems, especially systems of fast delivery, networks of logistic and distribution centres and cargo traffic terminals of the big cities, etc. The paper defines single and multiple allocations and studies the numerical examples. The capacitated single allocation hub location problems have been studied, with the provision of a mathematical model of selecting the location for the hubs on the network. The paper also presents the differences in the possibilities of implementing the exact and heuristic methods to solve the actual location problems of big dimensions i.e. hub problems of the big cities.

  12. Altered cortical hubs in functional brain networks in amyotrophic lateral sclerosis.

    Science.gov (United States)

    Ma, Xujing; Zhang, Jiuquan; Zhang, Youxue; Chen, Heng; Li, Rong; Wang, Jian; Chen, Huafu

    2015-11-01

    Cortical hubs are highly connected nodes in functional brain networks that play vital roles in the efficient transfer of information across brain regions. Although altered functional connectivity has been found in amyotrophic lateral sclerosis (ALS), the changing pattern in functional network hubs in ALS remains unknown. In this study, we applied a voxel-wise method to investigate the changing pattern of cortical hubs in ALS. Through resting-state fMRI, we constructed whole-brain voxel-wise functional networks by measuring the temporal correlations of each pair of brain voxels and identified hubs using the graph theory method. Specifically, a functional connectivity strength (FCS) map was derived from the data on 20 patients with ALS and 20 healthy controls. The brain regions with high FCS values were regarded as functional network hubs. Functional hubs were found mainly in the bilateral precuneus, parietal cortex, medial prefrontal cortex, and in several visual regions and temporal areas in both groups. Within the hub regions, the ALS patients exhibited higher FCS in the prefrontal cortex compared with the healthy controls. The FCS value in the significantly abnormal hub regions was correlated with clinical variables. Results indicated the presence of altered cortical hubs in the ALS patients and could therefore shed light on the pathophysiology mechanisms underlying ALS.

  13. Vitamin D Biology in Heart Failure : Molecular Mechanisms and Systematic Review

    NARCIS (Netherlands)

    Meems, Laura M. G.; van der Harst, P.; van Gilst, W. H.; de Boer, R. A.

    Vitamin D has recently been suggested as an important mediator of blood pressure and cardiovascular disease, including heart failure. In patients with heart failure, low vitamin D levels are associated with adverse outcome and correlate with established clinical correlates and biomarkers. Many

  14. Optimum hub height of a wind turbine for maximizing annual net profit

    International Nuclear Information System (INIS)

    Lee, Jaehwan; Kim, Dong Rip; Lee, Kwan-Soo

    2015-01-01

    Highlights: • Annual Net Profit was proposed to optimize the hub height of a wind turbine. • Procedures of the hub height optimization method were introduced. • Effect of local wind speed characteristics on optimum hub height was illustrated. • Effect of rated power on optimum hub height was negligible in the range 0.75–3 MW. • Rated speed and cut-out speed had great effects on optimum hub height. - Abstract: The optimization method of the hub height, which can ensure the economic feasibility of the wind turbine, is proposed in this study. Annual Net Profit is suggested as an objective function and the optimization procedure is developed. The effects of local wind speed and wind turbine power characteristics on the optimum hub height are investigated. The optimum hub height decreased as the mean wind speed and wind shear exponent increased. Rated power had little effect on optimum hub height; it follows that the economies of scale are negligible in the rated power range of 0.75–3 MW. Among the wind turbine power characteristics, rated speed and cut-out speed most strongly affected the optimum hub height

  15. Development of a linear motion antenna for the JT-60SA ECRF system

    International Nuclear Information System (INIS)

    Moriyama, Shinichi; Kobayashi, Takayuki; Isayama, Akihiko; Hoshino, Katsumichi; Suzuki, Sadaaki; Hiranai, Shinichi; Yokokura, Kenji; Sawahata, Masayuki; Terakado, Masayuki; Hinata, Jun; Wada, Kenji; Sato, Yoshikatsu

    2013-01-01

    Highlights: ► Development of an antenna featuring linear motion (LM) concept for long pulse electron cyclotron range of frequency (ECRF) heating and current drive in JT-60SA is in progress. ► A mock-up using a metallic sliding bearing with solid lubricant was fabricated. ► A vacuum pumping test with mass analyzer showed evidence of some hydrocarbons during shaft motion. ► Injection beam profile in toroidal beam scan was checked by low power measurement with mock-up. ► Current drive characteristics with the LM antenna for typical experimental scenarios of JT-60SA have been investigated by calculation. -- Abstract: Development of an antenna that features the linear motion (LM) concept for long-pulse electron-cyclotron range of frequency heating and current drive for the JT-60SA is in progress. Combining a linearly movable first mirror and a fixed curved second mirror allows the injection-beam angle to be controlled. Cooling water is fed through the drive shaft for the first mirror and through the fixed support for the second mirror. The shaft support structure uses a metallic sliding bearing with a solid lubricant. The sliding bearing supports combined linear and rotational motion, whereas a conventional ball bearing supports either linear or rotational motion. Therefore, the sliding bearing offers the advantage of reducing the support-structure volume, which is important in the design of the relatively narrow port duct of the JT-60SA. Recently, the sliding bearing has been installed into the mockup. Results of a vacuum test with a mass analyzer indicate the presence of hydrocarbons during shaft motion. The injection-beam profile obtained from a toroidal beam scan is checked against low-power measurements taken on the mockup. Finally, for typical JT-60SA experimental scenarios, heating- and current-drive characteristics of the LM antenna are investigated theoretically

  16. Activation analysis for JT-60U experiments with deuterium gases

    International Nuclear Information System (INIS)

    Miya, Naoyuki

    1993-11-01

    Identification of radionuclides and evaluation of dose rate level have been made on the structural materials of the JT-60U tokamak device. A one-dimensional neutron and gamma-ray transport code ANISN and an induced activation calculation code CINAC are used in this work. Radionuclides of 56 Mn (High-Mn steel toroidal field coil case), 58 Co (Inconel-625 vessel) and 60 Co (SS-316 first wall supporting material) appeared on the structures, which contribute to the dose rate around a vacuum vessel. Cobalt-58 and 60 Co with long half-life time intensely make residual activation in the time of 3 days to 3 months corresponding to the maintenance time after shutdown. The calculated dose rate on the vessel agreed well with the measured data in the first 2 years D-D operations. The one-dimensional code provided a sufficient prediction for the dose rate, although an error due to the toroidal field coil modeling in the calculation is estimated within ∼30%. (author)

  17. Fast neutron-gamma discrimination on neutron emission profile measurement on JT-60U

    International Nuclear Information System (INIS)

    Ishii, K.; Okamoto, A.; Kitajima, S.; Sasao, M.; Shinohara, K.; Ishikawa, M.; Baba, M.; Isobe, M.

    2010-01-01

    A digital signal processing (DSP) system is applied to stilbene scintillation detectors of the multichannel neutron emission profile monitor in JT-60U. Automatic analysis of the neutron-γ pulse shape discrimination is a key issue to diminish the processing time in the DSP system, and it has been applied using the two-dimensional (2D) map. Linear discriminant function is used to determine the dividing line between neutron events and γ-ray events on a 2D map. In order to verify the validity of the dividing line determination, the pulse shape discrimination quality is evaluated. As a result, the γ-ray contamination in most of the beam heating phase was negligible compared with the statistical error with 10 ms time resolution.

  18. Diagnostic system for passive charge-exchange particle measurements on JT-60

    International Nuclear Information System (INIS)

    Nemoto, Masahiro; Tobita, Kenji; Kusama, Yoshinori; Takeuchi, Hiroshi

    1988-01-01

    In order to measure energy distributions of the charge-exchange neutral particles in the JT-60 experiments, a compact size electrostatic energy analyzer which the measurable energy range is from 1 keV to 100 keV is developed successfully. Compactness of an analyzer is accomplished by setting an accelerator between a gas stripping cell and a deflector of 45deg injection type. The calibration of the analyzer was carried out owing to confirm the capability of energy analysis and stripping efficiency. This analyzer was applied to measure the energy distribution in additionally heated plasmas in JT-60. The usefullness of the analyzer was confirmed. (author)

  19. Dielectric Spectroscopic Detection of Early Failures in 3-D Integrated Circuits.

    Science.gov (United States)

    Obeng, Yaw; Okoro, C A; Ahn, Jung-Joon; You, Lin; Kopanski, Joseph J

    The commercial introduction of three dimensional integrated circuits (3D-ICs) has been hindered by reliability challenges, such as stress related failures, resistivity changes, and unexplained early failures. In this paper, we discuss a new RF-based metrology, based on dielectric spectroscopy, for detecting and characterizing electrically active defects in fully integrated 3D devices. These defects are traceable to the chemistry of the insolation dielectrics used in the through silicon via (TSV) construction. We show that these defects may be responsible for some of the unexplained early reliability failures observed in TSV enabled 3D devices.

  20. Report on survey on international hub

    International Nuclear Information System (INIS)

    Ebisawa, Hirobumi; Hoshino, Junko; Hashimoto, Kazuichiro; Okada, Sohei

    2011-06-01

    Japan Atomic Energy Agency (JAEA) is promoting initiative to form an international hub in line with its aim to accept more researchers/engineers from all over the world. Establishment of 'the Committee for JAEA Internationalization Initiative' was planned in 2010 so as to intensify this initiative, and in February, 2010, we visited research institutions in Europe, which include European Organization for Nuclear Research (CERN), the construction site of ITER in Cadarache, and Rutherford Appleton Laboratory (RAL), with the intention to survey and learn their advanced activities and systems in regard to the International Hub, so that the committee will be able to make fruitful discussion. This report describes strategy taken in each institution for an International Hub, and the state of each institution regarding acceptance and management of overseas researchers and engineers, research environment, living environment/health and welfare, and PR activities/coexistence with the local community. (author)

  1. Crossover from 2d to 3d in anisotropic Kondo lattices

    International Nuclear Information System (INIS)

    Reyes, D.; Continentino, M.A.

    2008-01-01

    We study the crossover from two to three dimensions in Kondo lattices (KLM) using the Kondo necklace model (KNM). In order to diagonalize the KNM, we use a representation for the localized and conduction electron spins in terms of bond operators and a decoupling for the relevant Green's functions. Both models have a quantum critical point at a finite value of the ratio (J/t) between the Kondo coupling (J) and the hopping (t). In 2d there is no line of finite temperature antiferromagnetic (AF) transitions while for d≥3 this line is given by, T N ∝|g| 1/(d-1) [D. Reyes, M.A. Continentino, Phys. Rev. B 76 (2007) 075114]. The crossover from 2d to 3d is investigated by turning on the electronic hopping (t -perpendicular ) of conduction electrons between different planes. The phase diagram as a function of temperature T, J/t -parallel and ξ=t -perpendicular /t -parallel , where t -parallel is the hopping within the planes is calculated

  2. Numerical investigation of hub clearance flow in a Kaplan turbine

    Science.gov (United States)

    Wu, H.; Feng, J. J.; Wu, G. K.; Luo, X. Q.

    2012-11-01

    In this paper, the flow field considering the hub clearance flow in a Kaplan turbine has been investigated through using the commercial CFD code ANSYS CFX based on high-quality structured grids generated by ANSYS ICEM CFD. The turbulence is simulated by k-ω based shear stress transport (SST) turbulence model together with automatic near wall treatments. Four kinds of simulations have been conducted for the runner geometry without hub clearance, with only the hub front clearance, with only the rear hub clearance, and with both front and rear clearance. The analysis of the obtained results is focused on the flow structure of the hub clearance flow, the effect on the turbine performance including hydraulic efficiency and cavitation performance, which can improve the understanding on the flow field in a Kaplan turbine.

  3. Numerical investigation of hub clearance flow in a Kaplan turbine

    International Nuclear Information System (INIS)

    Wu, H; Feng, J J; Wu, G K; Luo, X Q

    2012-01-01

    In this paper, the flow field considering the hub clearance flow in a Kaplan turbine has been investigated through using the commercial CFD code ANSYS CFX based on high-quality structured grids generated by ANSYS ICEM CFD. The turbulence is simulated by k-ω based shear stress transport (SST) turbulence model together with automatic near wall treatments. Four kinds of simulations have been conducted for the runner geometry without hub clearance, with only the hub front clearance, with only the rear hub clearance, and with both front and rear clearance. The analysis of the obtained results is focused on the flow structure of the hub clearance flow, the effect on the turbine performance including hydraulic efficiency and cavitation performance, which can improve the understanding on the flow field in a Kaplan turbine.

  4. Analysis of JT-60SA operational scenarios

    Science.gov (United States)

    Garzotti, L.; Barbato, E.; Garcia, J.; Hayashi, N.; Voitsekhovitch, I.; Giruzzi, G.; Maget, P.; Romanelli, M.; Saarelma, S.; Stankiewitz, R.; Yoshida, M.; Zagórski, R.

    2018-02-01

    Reference scenarios for the JT-60SA tokamak have been simulated with one-dimensional transport codes to assess the stationary state of the flat-top phase and provide a profile database for further physics studies (e.g. MHD stability, gyrokinetic analysis) and diagnostics design. The types of scenario considered vary from pulsed standard H-mode to advanced non-inductive steady-state plasmas. In this paper we present the results obtained with the ASTRA, CRONOS, JINTRAC and TOPICS codes equipped with the Bohm/gyro-Bohm, CDBM and GLF23 transport models. The scenarios analysed here are: a standard ELMy H-mode, a hybrid scenario and a non-inductive steady state plasma, with operational parameters from the JT-60SA research plan. Several simulations of the scenarios under consideration have been performed with the above mentioned codes and transport models. The results from the different codes are in broad agreement and the main plasma parameters generally agree well with the zero dimensional estimates reported previously. The sensitivity of the results to different transport models and, in some cases, to the ELM/pedestal model has been investigated.

  5. A versatile framework for cooperative hub network development

    NARCIS (Netherlands)

    Cruijssen, F.C.A.M.; Borm, P.; Dullaert, W.; Hamers, H.

    2010-01-01

    This paper introduces a framework for cooperative hub network development. Building a joint physical hub for the transshipment of goods is expensive and, therefore, involves considerable risks for cooperating companies. In a practical setting, it is unlikely that an entire network will be built at

  6. A versatile framework for cooperative hub network development

    NARCIS (Netherlands)

    Cruijssen, Frans; Borm, Peter; Dullaert, Wout; Hamers, Herbert

    This paper introduces a framework for cooperative hub network development. Building a joint physical hub for the transshipment of goods is expensive and, therefore, involves considerable risks for cooperating companies. In a practical setting, it is unlikely that an entire network will be built at

  7. Structural analysis of the JT-60SA cryostat vessel body

    Energy Technology Data Exchange (ETDEWEB)

    Botija, José, E-mail: jose.botija@ciemat.es [Association EURATOM – CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Alonso, Javier; Fernández, Pilar; Medrano, Mercedes; Ramos, Francisco; Rincon, Esther; Soleto, Alfonso [Association EURATOM – CIEMAT, Avda. Complutense 40, 28040 Madrid (Spain); Davis, Sam; Di Pietro, Enrico; Tomarchio, Valerio [Fusion for Energy, JT-60SA European Home Team, 85748 Garching bei Munchen (Germany); Masaki, Kei; Sakasai, Akira; Shibama, Yusuke [JAEA – Japan Atomic Energy Agency, Naka Fusion Institute, Ibaraki 311-0193 (Japan)

    2013-10-15

    Highlights: ► Structural analysis to validate the JT-60SA cryostat vessel body design. ► Design code ASME 2007 “Boiler and Pressure Vessel Code. Section VIII”. ► First buckling mode: load multiplier of 10.644, higher than the minimum factor 4.7. ► Elastic and elastic–plastic stress analysis meets ASME against plastic collapse. ► Bolted fasteners have been analyzed showing small gaps closed by strong welding. -- Abstract: The JT-60SA cryostat is a stainless steel vacuum vessel (14 m diameter, 16 m height) which encloses the Tokamak providing the vacuum environment (10{sup −3} Pa) necessary to limit the transmission of thermal loads to the components at cryogenic temperature. It must withstand both external atmospheric pressure during normal operation and internal overpressure in case of an accident. The paper summarizes the structural analyses performed in order to validate the JT-60SA cryostat vessel body design. It comprises several analyses: a buckling analysis to demonstrate stability under the external pressure; an elastic and an elastic–plastic stress analysis according to ASME VIII rules, to evaluate resistance to plastic collapse including localized stress concentrations; and, finally, a detailed analysis with bolted fasteners in order to evaluate the behavior of the flanges, assuring the integrity of the vacuum sealing welds of the cryostat vessel body.

  8. Quality control of the software in the JT-60 computer control system

    International Nuclear Information System (INIS)

    Isaji, Nobuaki; Kurihara, Kenichi; Kimura, Toyoaki

    1990-07-01

    The JT-60 Control System should be improved corresponding to the experimental requirements. In order to keep the integrity of the system even in the modification the concept of quality control (QC) was introduced in the software development. What we have done for QC activity are (1) to establish standard procedures of the software development, (2) to develop support tools for grasping the present status of the program structure, and (3) to develop a document system, and a source program management system. This paper reports these QC activities and their problems for the JT-60 control system. (author)

  9. Study of carbon impurity generation by chemical sputtering in JT-60U

    International Nuclear Information System (INIS)

    Higashijima, S.; Kubo, H.; Sugie, T.; Shimizu, K.; Asakura, N.; Itami, K.; Hosogane, N.; Sakasai, A.; Konoshima, S.; Sakurai, S.; Takenaga, H.

    1997-01-01

    CD/CH-band intensities emitted from hydrocarbon molecules have been measured in the divertor region of JT-60U and the chemical sputtering yield of methane was estimated as a function of the surface temperature and the deuterium ion flux. The chemical sputtering yield increases with the surface temperature and decreases with increasing ion flux density in the L-mode plasmas. The B 4 C converted CFC tiles are installed in JT-60U and it is found that the chemical sputtering of B 4 C converted CFC tiles is suppressed in comparison to normal CFC tiles. (orig.)

  10. Idea Exchange Music Hub Hits the Right Note in Community

    Directory of Open Access Journals (Sweden)

    Greg Bester

    2014-06-01

    Full Text Available The Cambridge Libraries and Galleries has made many changes over the last two years, rebranding as Idea Exchange and adding 3D printers, creative spaces and many on-site events. This article focuses on one of the organization’s newest innovations, the addition of a Music Hub, and the challenges of creating a space where members can learn and collaborate musically without disturbing those around them.

  11. International Education Hubs: Collaboration for Competitiveness and Sustainability

    Science.gov (United States)

    Knight, Jane

    2014-01-01

    This chapter focuses on the development of education hubs, a recent phenomenon in international higher education. Three models of hubs are examined in relation to the forces, risks, and opportunities of globalization and how local and international collaborations are essential for both global competitiveness and sustainability.

  12. Experimental study of radiation losses on the JT-60 tokamak

    International Nuclear Information System (INIS)

    Nishitani, Takeo

    1990-06-01

    Bolometric measurement system and associated diagnostics, soft x-ray pulse-height-analyzer, soft x-ray intensity and Balmer α line measurement systems, were developed to investigate the radiation losses of the JT-60 plasmas. The bolometric measurement is the most important diagnostics in the radiation loss study. The soft x-ray pulse-height-analyzer is useful to estimate the metallic impurity concentration, and the soft x-ray intensity and Balmer α line measurements are monitors of radiation in x-ray region and particle recycling in the plasma edge, respectively. In JT-60, the marfe has been observed frequently in high-Ip and high density limited discharges with NB heating after the replacement of the first wall from TiC coated molybdenum tiles to graphite ones. The threshold electron density of the marfe onset increased with the NB power. The empirical scaling of the marfe onset taking account of the NB power was obtained. This scaling was useful to predict the marfe onset condition in NB heated discharges on JT-60. The marfe was modelled based on the radiative thermal instability. The simple model can explain the marfe onset condition. The radiated power from the plasma with marfe was about 90 % of the absorbed power. Both stored energy and central electron temperatures did not change by the marfe onset in spite of the such intense radiation loss. Finally, this study revealed that the most clean plasma was obtained in the metallic first wall with the divertor on JT-60. This fact is suggesting the capability of the metallic material for the first wall of next devices. Enhance radiation localized in the peripheral plasma such as marfe and IDC does not degrade the core plasma confinement or somewhat improves it, so that marfe and IDC are suitable operational regime in the high density region for future devices because they have strong remote-radiative-cooling-effect. (J.P.N.)

  13. Development of an improved low profile hub seal refurbishment tool

    International Nuclear Information System (INIS)

    Wagg, L.

    1997-01-01

    The hub seal area of a fuel channel feeder coupling can be exposed to oxygen in the atmosphere if protective measures are not taken during maintenance outages. Exposure to oxygen can lead to pitting of the hub seal area. Although this is a rare occurrence, the resulting possibility of the feeder coupling leakage led to the development of a feeder hub refurbishment tool. To reduce time and man-rem exposure during feeder hub seal refurbishment, an improved low profile hub seat refurbishing tool has been developed. The improved tool design will allow for quick and controlled removal of material, and the restoration of a roll-burnished finish equivalent to the original requirements. The new tool can be used in maintenance operations, with the end fitting present, as well as under retube-type circumstances, with the end fitting removed. (author)

  14. Development of virtual private network for JT-60SA CAD integration

    International Nuclear Information System (INIS)

    Oshima, Takayuki; Fujita, Takaaki; Seki, Masami; Kawashima, Hisato; Hoshino, Katsumichi; Shibanuma, Kiyoshi; Verrecchia, M.; Teuchner, B.

    2010-01-01

    The CAD models will be exchanged and integrated at Naka for JT-60SA, a common computer network efficiently connected between Naka site and the Garching site is needed to be established. Virtual Private Network (VPN) was introduced with LAN on computer network physically-separated from JAEA intranet area and firewall. In July 2009, a new VPN connection between the Naka and Garching sites has been successfully demonstrated using IPSec-VPN technology with a commercial and cost-effective firewall/router for security. It was found that the introduction of the Wide Area File Service (WAFS) could solve the issue of the data transmission time and enhance the usability of the VPN for design integration in JT-60SA. (author)

  15. Stochastic optimization of energy hub operation with consideration of thermal energy market and demand response

    International Nuclear Information System (INIS)

    Vahid-Pakdel, M.J.; Nojavan, Sayyad; Mohammadi-ivatloo, B.; Zare, Kazem

    2017-01-01

    Highlights: • Studying heating market impact on energy hub operation considering price uncertainty. • Investigating impact of implementation of heat demand response on hub operation. • Presenting stochastic method to consider wind generation and prices uncertainties. - Abstract: Multi carrier energy systems or energy hubs has provided more flexibility for energy management systems. On the other hand, due to mutual impact of different energy carriers in energy hubs, energy management studies become more challengeable. The initial patterns of energy demands from grids point of view can be modified by optimal scheduling of energy hubs. In this work, optimal operation of multi carrier energy system has been studied in the presence of wind farm, electrical and thermal storage systems, electrical and thermal demand response programs, electricity market and thermal energy market. Stochastic programming is implemented for modeling the system uncertainties such as demands, market prices and wind speed. It is shown that adding new source of heat energy for providing demand of consumers with market mechanism changes the optimal operation point of multi carrier energy system. Presented mixed integer linear formulation for the problem has been solved by executing CPLEX solver of GAMS optimization software. Simulation results shows that hub’s operation cost reduces up to 4.8% by enabling the option of using thermal energy market for meeting heat demand.

  16. Association between vitamin D deficiency and heart failure risk in the elderly.

    Science.gov (United States)

    Porto, Catarina Magalhães; Silva, Vanessa De Lima; da Luz, João Soares Brito; Filho, Brivaldo Markman; da Silveira, Vera Magalhães

    2018-02-01

    The aim of this study was to evaluate the association between vitamin D deficiency and risk of heart failure in elderly patients of cardiology outpatient clinics. A cross-sectional study with an analytical approach was employed. Clinical data were collected from the elderly from August 2015 to February 2016. The dependent variable was the risk of heart failure; the independent variable was vitamin D deficiency; and intervening factors were age, gender, education, ethnicity, hypertension, diabetes mellitus, hypothyroidism, renal failure, dementia, stroke, dyslipidaemia, depression, smoking, alcoholism, obesity, andropause, and cardiac arrhythmia. To analyse the association between vitamin D deficiency and risk of heart failure, we used the bivariate logistic analysis, followed by analysis through the multivariate logistic regression model. Of the 137 elderly, the study found the following: women (75.9%); overweight (48.2%); obese (30.6%); increase in the index waist/hip (88.3%); dyslipidaemia (94.2%) and hypertension (91.2%); coronary artery disease (35.0%); and 27.7% with cardiac arrhythmia or left ventricular hypertrophy. Sixty-five per cent of the elderly were deficient in vitamin D. The risk of heart failure was significantly associated with vitamin D deficiency [odds ratio (OR): 12.19; 95% confidence interval (CI) = 4.23-35.16; P = 0.000], male gender (OR: 15.32; 95% CI = 3.39-69.20, P = 0.000), obesity (OR: 4.17; 95% CI = 1.36-12.81; P = 0.012), and cardiac arrhythmia (OR: 3.69; 95% CI = 1.23-11.11; P = 0.020). There was a high prevalence of vitamin D deficiency in the elderly, and the evidence shows a strong association between vitamin D deficiency and increased risk of heart failure in this population. © 2017 The Authors. ESC Heart Failure published by John Wiley & Sons Ltd on behalf of the European Society of Cardiology.

  17. Review of JT-60 experimental results from June to October, 1987

    International Nuclear Information System (INIS)

    1988-03-01

    This is a prompt report on JT-60 experimental results from June to October, 1987. Experiments in hydrogen plasmas have been undertaken with up to 3.2 MA of plasma current in limiter discharges, 2.7 MA in divertor discharges, and 30 MW of total NB (H 0 → H + ) and RF injection power. In limiter discharges with ∼3 MA plasma current, the maximum central electron density of 1.3 x 10 20 m -3 and the energy confinement time of 0.15 - 0.18 sec were obtained with heating powers of 13 - 20 MW. The total plasma stored energy of 3.1 MJ, and n e (0)τ E of 1.4 - 1.8 x 10 19 m -3 sec were achieved. The best set of parameters achieved is n e (0)τ E = 1.8 x 10 19 m -3 sec and T i (0) = 3.7 KeV at plasma current of 3.2 MA. By applying deutrium discharge condition, n e (0)τ E and T i (0) enter the JT-60 target area determined by Atomic Energy Commission. Many short periods (50 - 100 ms) of H-mode phase are found in outside X-point divertor discharges with NB or NB + RF (LH or IC) heating power of more than 16 MW, although at present the energy confinement improvement is limited to within 10 %. In combined LH and NB heating of low-n-bar e discharge, the plasma stored energy increases with the same rate as NB heating only, with preferential absorption of LH wave to the high energy beam ions. In combined NB and on-axis ICRF heating of low-n-bar e discharge, a high incremental energy confinement time is obtained, with strong high energy beam ion acceleration and electron heating in the central region of the plasma. (author)

  18. Neural-net disruption predictor in JT-60U

    International Nuclear Information System (INIS)

    Yoshino, R.

    2003-01-01

    The prediction of major disruptions caused by the density limit, the plasma current ramp-down with high internal inductance l i , the low density locked mode and the β-limit has been investigated in JT-60U. The concept of 'stability level', newly proposed in this paper to predict the occurrence of a major disruption, is calculated from nine input parameters every 2 ms by the neural network and the start of a major disruption is predicted when the stability level decreases to a certain level, the 'alarm level'. The neural network is trained in two steps. It is first trained with 12 disruptive and six non-disruptive shots (total of 8011 data points). Second, the target output data for 12 disruptive shots are modified and the network is trained again with additional data points generated by the operator. The 'neural-net disruption predictor' obtained has been tested for 300 disruptive shots (128 945 data points) and 1008 non-disruptive shots (982 800 data points) selected from nine years of operation (1991-1999) of JT-60U. Major disruptions except for those caused by the -limit have been predicted with a prediction success rate of 97-98% at 10 ms prior to the disruption and higher than 90% at 30 ms prior to the disruption while the false alarm rate is 2.1% for non-disruptive shots. This prediction performance has been confirmed for 120 disruptive shots (56 163 data points), caused by the density limit, as well as 1032 non-disruptive shots (1004 611 data points) in the last four years of operation (1999-2002) of JT-60U. A careful selection of the input parameters supplied to the network and the newly developed two-step training of the network have reduced the false alarm rate resulting in a considerable improvement of the prediction success rate. (author)

  19. Integrated technology rotor/flight research rotor hub concept definition

    Science.gov (United States)

    Dixon, P. G. C.

    1983-01-01

    Two variations of the helicopter bearingless main rotor hub concept are proposed as bases for further development in the preliminary design phase of the Integrated Technology Rotor/Flight Research Rotor (ITR/FRR) program. This selection was the result of an evaluation of three bearingless hub concepts and two articulated hub concepts with elastomeric bearings. The characteristics of each concept were evaluated by means of simplified methodology. These characteristics included the assessment of stability, vulnerability, weight, drag, cost, stiffness, fatigue life, maintainability, and reliability.

  20. Mechanism of vertical displacement events in JT-60U disruptive discharges

    International Nuclear Information System (INIS)

    Nakamura, Y.; Yoshino, R.; Neyatani, Y.; Tsunematsu, T.; Azumi, M.; Pomphrey, N.; Jardin, S.C.

    1996-01-01

    Enhanced vertical displacement events (VDEs), which are frequently observed in JT-60U disruptive discharges, are investigated using the Tokamak Simulation Code (TSC). The rapid plasma current quench can accelerate the vertical displacement, owing to both the up/down asymmetry of the eddy current distribution arising from the asymmetric geometry of the JT-60U vacuum vessel and the degradation of magnetic field decay index n, leading to high growth rates of positional instability. For a slightly elongated configuration (n = -0.9), the asymmetry of attractive forces on the toroidal plasma plays a dominant role in the VDE mechanism. For a more elongated configuration (n = -1.7), the degradation of field decay index n plays an important role on VDEs, in addition to the effect of asymmetric attractive forces. It is shown that the VDE characteristics of a highly elongated configuration with a rapid plasma current quench can be dominated by the field decay index degradation. It is also pointed out that both the softening of current quenches as was experimentally developed in the JT-60U tokamak, and the optimization of the allowable elongation of the plasma cross-section are critical issues in the development of a general control strategy of discharge termination. (author). 21 refs, 10 figs

  1. Very fast feedback control of coil-current in JT-60 tokamak

    International Nuclear Information System (INIS)

    Aoyagi, T.; Terakado, T.; Takahashi, M.; Nobusaka, H.; Yagyu, J.; Matsuzaki, Y.

    1992-01-01

    A direct digital control (DDC) system is adopted for controlling thyristor converters of power supplies in the JT-60 tokamak built in 1984. Microcomputers of the DDC were 5 MHz i8086 microprocessor and programs were written by assembler language and the processing time was under 1ms. They were, however, too old in hardware and too complicated in software. New DDC system has been made in the JT-60 Upgrade (JT-60U) to control the power supplies more quickly under 0.25 and 0.5 ms of the processing time and also to write the programs used by high-level language. The new system consists of a host computer and five microcomputers with microprocessor on VME bus system. The host computer AS3260 performs on-line processing such as setting the DDC under the discharge conditions and so on. Functions of the microcomputers with a 32-bit, 20 MHz microprocessor MC68030, whose OS are VxWorks and programs are written by C language, are real-time processing such as taking in instructions from a ZENKEI computer and in feedback control of currents and voltages of coils every 0.25 and 0.5 ms. The system is now operating very smoothly. (author)

  2. Design and Structural Analysis for the Vacuum Vessel of Superconducting Tokamak JT-60SC

    International Nuclear Information System (INIS)

    Kudo, Y.; Sakurai, S.; Masaki, K.; Urata, K.; Sasajima, T.; Matsukawa, M.; Sakasai, A.; Ishida, S.

    2003-01-01

    A modification of the JT-60 is planned to be a superconducting tokamak (JT-60SC) in order to establish steady-state operation of high beta plasma for 100 s, and to ensure the applicability of ferritic steel as a reduced activation material for reactor relevant break-even class plasmas. This paper describes the detailed design of the vacuum vessel, which has a unique structure for cost effective manufacturing, as well as structural analysis results for a feasibility study

  3. E-hubs: the new B2B (business-to-business) marketplaces.

    Science.gov (United States)

    Kaplan, S; Sawhney, M

    2000-01-01

    Electronic hubs--Internet-based intermediaries that host electronic marketplaces and mediate transactions among businesses--are generating a lot of interest. Companies like Ariba, Chemdex, and Commerce One have already attained breathtaking stock market capitalizations. Venture capitalists are pouring money into more business-to-business start-ups. Even industrial stalwarts like GM and Ford are making plans to set up their own Web markets. As new entrants with new business models pour into the business-to-business space, it's increasingly difficult to make sense of the landscape. This article provides a blueprint of the e-hub arena. The authors start by looking at the two dimensions of purchasing: what businesses buy--manufacturing inputs or operating inputs--and how they buy--through systematic sourcing or spot sourcing. They classify B2B e-hubs into four categories: MRO hubs, yield managers, exchanges, and catalog hubs, and they discuss each type in detail. Drilling deeper into this B2B matrix, the authors look at how e-hubs create value--through aggregation and matching--and explain when each mechanism works best. They also examine the biases of e-hubs. Although many e-hubs are neutral--they're operated by independent third parties--some favor the buyers or sellers. The authors explain the differences and discuss the pros and cons of each position. The B2B marketplace is changing rapidly. This framework helps buyers, sellers, and market makers navigate the landscape by explaining what the different hubs do and how they add the most value.

  4. Performance of RF power and phase control on JT-60 LHRF heating system

    International Nuclear Information System (INIS)

    Fujii, T.; Ikeda, Y.; Imai, T.; Honda, M.; Kiyono, K.; Maebara, S.; Saigusa, M.; Sakamoto, K.; Sawahata, M.; Seki, M.

    1987-01-01

    The performance of RF power and phase control on the JT-60 LHRFD heating system are presented. The JT-60 LHRF heating system has three units of huge RF source with a total output of 24 MW, each unit consisting of eight amplifier chains. A high power klystron generating 1 MW for 10 s at 2 GHz is used in each chain. Automatic gain control is employed to regulate the output power not only against gain fluctuations in the chain but also against the unstable plasma load without any output circulator for the klystron

  5. Review of ICRF antenna development and heating experiments up to advanced experiment I, 1989 on the JT-60 tokamak

    International Nuclear Information System (INIS)

    Fujii, Tsuneyuki

    1992-03-01

    Two main subjects of ion cyclotron range of frequencies (ICRF) heating on JT-60 are described in this paper from development phase of the JT-60 ICRF heating system up to advanced experiment I, 1989. One is antenna design and development for the high power JT-60 ICRF heating system (6 MW for 10 s at a frequency range of 108 - 132 MHz). The other is the experimental investigation of characteristics of second harmonic ICRF heating in a large tokamak. (J.P.N.)

  6. Progress of JT-60SA Project: EU-JA joint efforts for assembly and fabrication of superconducting tokamak facilities and its research planning

    Energy Technology Data Exchange (ETDEWEB)

    Shirai, Hiroshi, E-mail: shirai.hiroshi@jaea.go.jp [JT-60SA Project Team, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Barabaschi, Pietro [JT-60SA EU-Home Team, Fusion for Energy, Boltsmannstr 2, Garching 85748 (Germany); Kamada, Yutaka [JT-60SA JA-Home Team, Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2016-11-01

    Highlights: • JT-60SA Project is promoted under the BA Agreement and JA national programme. • JT-60SA is designed to operate in break-even equivalent condition for a long period. • JT-60SA Project supports and complements the ITER project, and promotes DEMO design. • Fabrication of JT-60SA components and assembly in Naka are steadily going on. • JT-60SA Research Plan has been developed jointly by EU and JA fusion communities. - Abstract: Aiming at supporting the early realization of fusion energy, the JT-60SA Project has shown steady progress for several years toward the first plasma in 2019 under the dual frameworks: the Satellite Tokamak Programme of the Broader Approach Agreement between EU and Japan, and the Japanese national programme. JT-60SA is a superconducting tokamak designed to operate in break-even equivalent conditions for a long pulse duration (typically 100 s) with a maximum plasma current of 5.5 MA. A variety of plasma control capabilities enable JT-60SA to contribute directly to the ITER project and also to DEMO by addressing key engineering and physics issues for advanced plasma operation. Design and fabrication of JT-60SA components, shared by the EU and Japan, started in 2007. Assembly in the torus hall started in January 2013, and welding work of the vacuum vessel sectors (seven 40° sectors and two 30° sectors) is currently ongoing on the cryostat base. Other components such as TF coils, PF coils, power supplies, cryogenic system, cryostat vessel, thermal shields and so on were or are being delivered to the Naka site for installation, assembly and commissioning. This paper gives technical progress on fabrication, installation and assembly of tokamak components and ancillary systems, as well as progress of the JT-60SA Research Plan being developed jointly by European and Japanese fusion communities.

  7. Design study of an AC power supply system in JT-60SA

    International Nuclear Information System (INIS)

    Shimada, Katsuhiro; Baulaigue, Olivier; Cara, Philippe; Coletti, Alberto; Coletti, Roberto; Matsukawa, Makoto; Terakado, Tsunehisa; Yamauchi, Kunihito

    2011-01-01

    In the initial research phase of JT-60SA, which is the International Thermonuclear Experimental Reactor (ITER) satellite Tokamak with superconducting toroidal and poloidal magnetic field coils, the plasma heating operation of 30 MW-60 s or 20 MW-100 s is planned for 5.5 MA single null divertor plasmas. To achieve this operation, AC power source of the medium voltage of 18 kV and ∼7 GJ has to be provided in total to the poloidal field coil power supplies and additional heating devices such as neutral beam injection (NBI) and electron cyclotron radio frequency (ECRF). In this paper, the proposed AC power supply system in JT-60SA was estimated from the view point of available power, and harmonic currents based on the standard plasma operation scenario during the initial research phase. This AC power supply system consists of the reused JT-60 power supply facilities including motor generators with flywheel, AC breakers, harmonic filters, etc., to make it cost effective. In addition, the conceptual design of the upgraded AC power supply system for the ultimate heating power of 41 MW-100 s in the extended research phase is also described.

  8. Ion beam dump for JT-60 NBI

    International Nuclear Information System (INIS)

    Kuriyama, Masaaki; Horiike, Hiroshi; Matsuda, Shinzaburo; Morita, Hiroaki; Shibanuma, Kiyoshi

    1981-10-01

    The design of the active cooling type ion beam dump for JT-60 NBI which receives the total beam power of 5.6 MW for 10 sec continuously is described. It is composed of array of many finned tubes which is made of oxygen free copper with 0.2% silver content. The safety margin against thermal and mechanical troubles is estimated by the heat transfer and the thermal stress calculation. (author)

  9. Characteristics of large scale ionic source for JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, Yukio; Honda, Atsushi; Inoue, Takashi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

    1997-02-01

    The Neutral Beam Injection (NBI) apparatus is expected for important role sharing apparatus to realize the plasma electric current drive and the plasma control in not only temperature upgrading of the plasma but also Tokamak nuclear fusion reactor for the next generation such as JT-60, ITER and so forth. Japan Atomic Energy Research Institute has developed the ionic source with high energy and large electric current for about 10 years. Some arrangement tests of the large negative ion source for JT-60 No. 1 were executed from June to October, 1995. As a series of arrangement tests, 400 KeV and 13.5 A of deuterium negative ion beam was successfully accelerated for 0.12 sec. under 0.22 Pa of low gas pressure. And, it was elucidated that electron electric current could be controlled efficiently even in deuterium negative ion beam. Here is described on the testing results in details. (G.K.)

  10. Review of JT-60U experimental results from February to October, 1995

    International Nuclear Information System (INIS)

    1996-03-01

    Renewed theme group organization started from October 1994 for the upcoming experiments in JT-60U. This regime has three theme groups each of which is composed of two sub-theme groups as; (1) Plasma Operation Theme (Leader Y. Neyatani) with Operation Sub-Theme and Disruption Sub-Theme, (2) High Performance (Leader S. Ishida) with Confinement and MHD Sub-Theme and High Energy Particle Sub-Theme and (3) Steady State Theme (Leader A. Sakasai) with Current Drive Sub-Theme and Divertor Sub-Theme. The main results from the JT-60U experiments in 1995 are summarized in the overviews of the three theme group activities. (J.P.N.)

  11. Review of JT-60U experimental results from February to October, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Renewed theme group organization started from October 1994 for the upcoming experiments in JT-60U. This regime has three theme groups each of which is composed of two sub-theme groups as; (1) Plasma Operation Theme (Leader Y. Neyatani) with Operation Sub-Theme and Disruption Sub-Theme, (2) High Performance (Leader S. Ishida) with Confinement and MHD Sub-Theme and High Energy Particle Sub-Theme and (3) Steady State Theme (Leader A. Sakasai) with Current Drive Sub-Theme and Divertor Sub-Theme. The main results from the JT-60U experiments in 1995 are summarized in the overviews of the three theme group activities. (J.P.N.).

  12. Sci-Hub provides access to nearly all scholarly literature.

    Science.gov (United States)

    Himmelstein, Daniel S; Romero, Ariel Rodriguez; Levernier, Jacob G; Munro, Thomas Anthony; McLaughlin, Stephen Reid; Greshake Tzovaras, Bastian; Greene, Casey S

    2018-03-01

    The website Sci-Hub enables users to download PDF versions of scholarly articles, including many articles that are paywalled at their journal's site. Sci-Hub has grown rapidly since its creation in 2011, but the extent of its coverage has been unclear. Here we report that, as of March 2017, Sci-Hub's database contains 68.9% of the 81.6 million scholarly articles registered with Crossref and 85.1% of articles published in toll access journals. We find that coverage varies by discipline and publisher, and that Sci-Hub preferentially covers popular, paywalled content. For toll access articles, we find that Sci-Hub provides greater coverage than the University of Pennsylvania, a major research university in the United States. Green open access to toll access articles via licit services, on the other hand, remains quite limited. Our interactive browser at https://greenelab.github.io/scihub allows users to explore these findings in more detail. For the first time, nearly all scholarly literature is available gratis to anyone with an Internet connection, suggesting the toll access business model may become unsustainable. © 2018, Himmelstein et al.

  13. Plasma equilibrium response modelling and validation on JT-60U

    International Nuclear Information System (INIS)

    Lister, J.B.; Sharma, A.; Limebeer, D.J.N.; Wainwright, J.P.; Nakamura, Y.; Yoshino, R.

    2002-01-01

    A systematic procedure to identify the plasma equilibrium response to the poloidal field coil voltages has been applied to the JT-60U tokamak. The required response was predicted with a high accuracy by a state-space model derived from first principles. The ab initio derivation of linearized plasma equilibrium response models is re-examined using an approach standard in analytical mechanics. A symmetric formulation is naturally obtained, removing a previous weakness in such models. RZIP, a rigid current distribution model, is re-derived using this approach and is compared with the new experimental plasma equilibrium response data obtained from Ohmic and neutral beam injection discharges in the JT-60U tokamak. In order to remove any bias from the comparison between modelled and measured plasma responses, the electromagnetic response model without plasma was first carefully tuned against experimental data, using a parametric approach, for which different cost functions for quantifying model agreement were explored. This approach additionally provides new indications of the accuracy to which various plasma parameters are known, and to the ordering of physical effects. Having taken these precautions when tuning the plasmaless model, an empirical estimate of the plasma self-inductance, the plasma resistance and its radial derivative could be established and compared with initial assumptions. Off-line tuning of the JT-60U controller is presented as an example of the improvements which might be obtained by using such a model of the plasma equilibrium response. (author)

  14. Progress of data processing system in JT-60 utilizing the UNIX-based workstations

    International Nuclear Information System (INIS)

    Sakata, Shinya; Kiyono, Kimihiro; Oshima, Takayuki; Sato, Minoru; Ozeki, Takahisa

    2007-07-01

    JT-60 data processing system (DPS) possesses three-level hierarchy. At the top level of hierarchy is JT-60 inter-shot processor (MSP-ISP), which is a mainframe computer, provides communication with the JT-60 supervisory control system and supervises the internal communication inside the DPS. The middle level of hierarchy has minicomputers and the bottom level of hierarchy has individual diagnostic subsystems, which consist of the CAMAC and VME modules. To meet the demand for advanced diagnostics, the DPS has been progressed in stages from a three-level hierarchy system, which was dependent on the processing power of the MSP-ISP, to a two-level hierarchy system, which is decentralized data processing system (New-DPS) by utilizing the UNIX-based workstations and network technology. This replacement had been accomplished, and the New-DPS has been started to operate in October 2005. In this report, we describe the development and improvement of the New-DPS, whose functions were decentralized from the MSP-ISP to the UNIX-based workstations. (author)

  15. Liner Shipping Hub Network Design in a Competitive Environment

    DEFF Research Database (Denmark)

    Gelareh, Shahin; Nickel, Stefan; Pisinger, David

    A new mixed integer programming formulation is proposed for hub-and-spoke network design in a competitive environment. It addresses competition between a newcomer liner service provider and an alliance, both operating on hub-and-spoke networks. The newcomer company maximizes its market share...... — proportional to service time and transportation cost —by locating a predefined number of hubs at candidate ports and designing its network. While general-purpose solvers do not solve instances of even small size, an accelerated lagrangian method coupled with a primal heuristic obtains very good bounds. Our...

  16. Multi-Item Distribution Policies with Supply Hub and Lateral Transshipment

    OpenAIRE

    Zhong Jin-Hong; Jiang Rui-Xuan; Zheng Gui

    2015-01-01

    Supply Hub is defined as the horizontal coordination among the suppliers while lateral transshipment is a horizontal coordination policy among the retailers. By considering the Supply Hub and lateral transshipment simultaneously, ones can reduce the total cost of the supply chain system and improve the response to customer requirement and the customers’ satisfaction. We investigate the distribution policies for the supply chain which consists of multisuppliers, single Supply Hub, and multidis...

  17. Revisiting date and party hubs: novel approaches to role assignment in protein interaction networks.

    Directory of Open Access Journals (Sweden)

    Sumeet Agarwal

    2010-06-01

    Full Text Available The idea of "date" and "party" hubs has been influential in the study of protein-protein interaction networks. Date hubs display low co-expression with their partners, whilst party hubs have high co-expression. It was proposed that party hubs are local coordinators whereas date hubs are global connectors. Here, we show that the reported importance of date hubs to network connectivity can in fact be attributed to a tiny subset of them. Crucially, these few, extremely central, hubs do not display particularly low expression correlation, undermining the idea of a link between this quantity and hub function. The date/party distinction was originally motivated by an approximately bimodal distribution of hub co-expression; we show that this feature is not always robust to methodological changes. Additionally, topological properties of hubs do not in general correlate with co-expression. However, we find significant correlations between interaction centrality and the functional similarity of the interacting proteins. We suggest that thinking in terms of a date/party dichotomy for hubs in protein interaction networks is not meaningful, and it might be more useful to conceive of roles for protein-protein interactions rather than for individual proteins.

  18. Classification of gene expression data: A hubness-aware semi-supervised approach.

    Science.gov (United States)

    Buza, Krisztian

    2016-04-01

    Classification of gene expression data is the common denominator of various biomedical recognition tasks. However, obtaining class labels for large training samples may be difficult or even impossible in many cases. Therefore, semi-supervised classification techniques are required as semi-supervised classifiers take advantage of unlabeled data. Gene expression data is high-dimensional which gives rise to the phenomena known under the umbrella of the curse of dimensionality, one of its recently explored aspects being the presence of hubs or hubness for short. Therefore, hubness-aware classifiers have been developed recently, such as Naive Hubness-Bayesian k-Nearest Neighbor (NHBNN). In this paper, we propose a semi-supervised extension of NHBNN which follows the self-training schema. As one of the core components of self-training is the certainty score, we propose a new hubness-aware certainty score. We performed experiments on publicly available gene expression data. These experiments show that the proposed classifier outperforms its competitors. We investigated the impact of each of the components (classification algorithm, semi-supervised technique, hubness-aware certainty score) separately and showed that each of these components are relevant to the performance of the proposed approach. Our results imply that our approach may increase classification accuracy and reduce computational costs (i.e., runtime). Based on the promising results presented in the paper, we envision that hubness-aware techniques will be used in various other biomedical machine learning tasks. In order to accelerate this process, we made an implementation of hubness-aware machine learning techniques publicly available in the PyHubs software package (http://www.biointelligence.hu/pyhubs) implemented in Python, one of the most popular programming languages of data science. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  19. Slope failures evaluation and landslides investigation using 2-D resistivity method

    Directory of Open Access Journals (Sweden)

    M.M. Nordiana

    2018-06-01

    Full Text Available Slope failure is a complex phenomenon that may caused to landslides. Buildings and infrastructure such as transportation facilities and pipelines located within the boundaries of a landslide can be damaged or destroyed. Slope failure classification and various factors contributing to the instability using 2-D resistivity survey conducted in Selangor, Malaysia are described. Six 2-D resistivity survey lines with 5 m minimum electrode spacing using Pole-dipole array were performed. The data were processed using Res2Dinv and surfer10 software to evaluate the subsurface characteristics. The 2-D resistivity results show that the subsurface consist of two main zones. The first zone was alluvium or highly weathered with resistivity value of 100–1000 Ω m and depth of >30 m. This zone consists of saturated area with resistivity value of 1–100 Ω m and boulders with resistivity value of 1200–7000 Ω m. The second zone with resistivity value of >7000 Ω m was interpreted as granitic bedrock. The study area was characterized by saturated zones, highly weathered zone, highly contain of sand and boulders that will trigger slope failure in the survey area. This will cause to low strength of soil, debris flow and movement of earth. On the basis of the case examples described, 2-D resistivity method is categorized into desirable and useful method in determination of slope failure and future assessments. Keywords: Slope failure, Landslides, 2-D resistivity, Saturated, Boulders

  20. Density limit in JT-60

    International Nuclear Information System (INIS)

    Kamada, Yutaka; Hosogane, Nobuyuki; Hirayama, Toshio; Tsunematsu, Toshihide

    1990-05-01

    This report studies mainly the density limit for a series of gas- and pellet-fuelled limiter discharges in JT-60. With the pellet injection into high-current/low-q (q(a)=2.3∼2.5) discharges, the Murakami factor reaches up to 10∼13 x 10 19 m -2 T -1 . The values are about factors of 1.5∼2.0 higher than those for usual gas-fuelled discharges. The pellet injected discharges have high central density, whereas the electron density in the outer region (a/2 abs and n e 2 (r=50 cm) x Z eff (r=50 cm). (author)

  1. JT-60 database system, 1

    International Nuclear Information System (INIS)

    Kurihara, Kenichi; Kimura, Toyoaki; Itoh, Yasuhiro.

    1987-07-01

    Naturally, sufficient software circumstance makes it possible to analyse the discharge result data effectively. JT-60 discharge result data, collected by the supervisor, are transferred to the general purpose computer through the new linkage channel, and are converted to ''database''. Datafile in the database was designed to be surrounded by various interfaces. This structure is able to preserve the datafile reliability and does not expect the user's information about the datafile structure. In addition, the support system for graphic processing was developed so that the user may easily obtain the figures with some calculations. This paper reports on the basic concept and system design. (author)

  2. Liner shipping hub network design in a competitive environment

    DEFF Research Database (Denmark)

    Gelareh, Shahin; Nickel, Stefan; Pisinger, David

    2010-01-01

    A mixed integer programming formulation is proposed for hub-and-spoke network design in a competitive environment. It addresses the competition between a newcomer liner service provider and an existing dominating operator, both operating on hub-and-spoke networks. The newcomer company maximizes i...

  3. Flow Merging and Hub Route Optimization in Collaborative Transportation

    Directory of Open Access Journals (Sweden)

    Kerui Weng

    2014-01-01

    Full Text Available This paper studies the optimal hub routing problem of merged tasks in collaborative transportation. This problem allows all carriers’ transportation tasks to reach the destinations optionally passing through 0, 1, or 2 hubs within limited distance, while a cost discount on arcs in the hub route could be acquired after paying fixed charges. The problem arises in the application of logistics, postal services, airline transportation, and so forth. We formulate the problem as a mixed-integer programming model, and provide two heuristic approaches, respectively, based on Lagrangian relaxation and Benders decomposition. Computational experiments show that the algorithms work well.

  4. Web-based Java application to advanced JT-60 Man-Machine Interfacing System for remote experiments

    International Nuclear Information System (INIS)

    Totsuka, Toshiyuki; Suzuki, Yoshio; Sakata, Shinya; Oshima, Takayuki; Iba, Katsuyuki

    2008-01-01

    Since remote participation in ITER experiments is planned, it is expected to demonstrate that the JT-60SA experiment is controlled from a Japanese remote experiment center located in Rokkasho-mura, Aomori-ken, Japan as a part of the ITER-BA project. Functions required for this experiment are monitoring of the discharge sequence status, handling of the discharge parameter, checking of experiment data, and monitoring of plant data, all of which are included in the existing JT-60 Man-Machine Interfacing System (MMIF). The MMIF is now only available to on-site users at the Naka site due to network safety. The motivation for remote MMIF is prompted by the issue of developing and achieving compatibility with network safety. The Java language has been chosen to implement this task. This paper deals with details of the JT-60 MMIF for the remote experiment that has evolved using the Java language

  5. Predicting the binding patterns of hub proteins: a study using yeast protein interaction networks.

    Directory of Open Access Journals (Sweden)

    Carson M Andorf

    Full Text Available Protein-protein interactions are critical to elucidating the role played by individual proteins in important biological pathways. Of particular interest are hub proteins that can interact with large numbers of partners and often play essential roles in cellular control. Depending on the number of binding sites, protein hubs can be classified at a structural level as singlish-interface hubs (SIH with one or two binding sites, or multiple-interface hubs (MIH with three or more binding sites. In terms of kinetics, hub proteins can be classified as date hubs (i.e., interact with different partners at different times or locations or party hubs (i.e., simultaneously interact with multiple partners.Our approach works in 3 phases: Phase I classifies if a protein is likely to bind with another protein. Phase II determines if a protein-binding (PB protein is a hub. Phase III classifies PB proteins as singlish-interface versus multiple-interface hubs and date versus party hubs. At each stage, we use sequence-based predictors trained using several standard machine learning techniques.Our method is able to predict whether a protein is a protein-binding protein with an accuracy of 94% and a correlation coefficient of 0.87; identify hubs from non-hubs with 100% accuracy for 30% of the data; distinguish date hubs/party hubs with 69% accuracy and area under ROC curve of 0.68; and SIH/MIH with 89% accuracy and area under ROC curve of 0.84. Because our method is based on sequence information alone, it can be used even in settings where reliable protein-protein interaction data or structures of protein-protein complexes are unavailable to obtain useful insights into the functional and evolutionary characteristics of proteins and their interactions.We provide a web server for our three-phase approach: http://hybsvm.gdcb.iastate.edu.

  6. Active Control of Inlet Noise on the JT15D Turbofan Engine

    Science.gov (United States)

    Smith, Jerome P.; Hutcheson, Florence V.; Burdisso, Ricardo A.; Fuller, Chris R.

    1999-01-01

    This report presents the key results obtained by the Vibration and Acoustics Laboratories at Virginia Tech over the year from November 1997 to December 1998 on the Active Noise Control of Turbofan Engines research project funded by NASA Langley Research Center. The concept of implementing active noise control techniques with fuselage-mounted error sensors is investigated both analytically and experimentally. The analytical part of the project involves the continued development of an advanced modeling technique to provide prediction and design guidelines for application of active noise control techniques to large, realistic high bypass engines of the type on which active control methods are expected to be applied. Results from the advanced analytical model are presented that show the effectiveness of the control strategies, and the analytical results presented for fuselage error sensors show good agreement with the experimentally observed results and provide additional insight into the control phenomena. Additional analytical results are presented for active noise control used in conjunction with a wavenumber sensing technique. The experimental work is carried out on a running JT15D turbofan jet engine in a test stand at Virginia Tech. The control strategy used in these tests was the feedforward Filtered-X LMS algorithm. The control inputs were supplied by single and multiple circumferential arrays of acoustic sources equipped with neodymium iron cobalt magnets mounted upstream of the fan. The reference signal was obtained from an inlet mounted eddy current probe. The error signals were obtained from a number of pressure transducers flush-mounted in a simulated fuselage section mounted in the engine test cell. The active control methods are investigated when implemented with the control sources embedded within the acoustically absorptive material on a passively-lined inlet. The experimental results show that the combination of active control techniques with fuselage

  7. High performance experiments in JT-60U reversed shear discharges

    International Nuclear Information System (INIS)

    Fujita, T.; Kamada, Y.; Ishida, S.

    2001-01-01

    The operation of JT-60U reversed shear discharges has been extended to a high plasma current, low-q regime keeping a large radius of the internal transport barrier (ITB) and the record value of equivalent fusion multiplication factor in JT-60U, Q DT eq =1.25, has been achieved at 2.6 MA. Operational schemes to reach the low-q regime with good reproducibility have been developed. The reduction of Z eff was obtained in the newly installed W-shaped pumped divertor. The beta limit in the low-q min regime, which limited the performance of L-mode edge discharges, has been improved in H-mode edge discharges with a broader pressure profile, which was obtained by power flow control with ITB degradation. Sustainment of ITB and improved confinement for 5.5 seconds has been demonstrated in an ELMy H reversed shear discharge. (author)

  8. Climate programs update: USDA Southwest Regional Climate Hub update

    Science.gov (United States)

    PROGRAM OVERVIEW: The overarching goal of the USDA SW Climate Hub is to assist farmers, ranchers and foresters in addressing the effects of climate change including prolonged drought, increased insect outbreaks and severe wildfires. In the first year of operations, the SW Climate Hub (est. Februa...

  9. Hub Status and Indexation of Container Ports

    Directory of Open Access Journals (Sweden)

    Yong-An Park

    2015-06-01

    This study develops two sub-indexes of port classification and capacity, and combines cases of these two sub-indexes into various types in order to find a proper port hub index. The paper demonstrates how different types of port hub index are useful measurements for evaluating outputs and inputs of container ports. In a case analysis we show that the indexes of period variables and lagged variables have more explanatory power with regard to changes of port throughputs and high correlation with inputs.

  10. Absolute calibration of the neutron yield measurement on JT-60 Upgrade

    International Nuclear Information System (INIS)

    Nishitani, Takeo; Takeuchi, Hiroshi; Barnes, C.W.

    1991-10-01

    Absolutely calibrated measurements of the neutron yield are important for the evaluation of the plasma performance such as the fusion gain Q in DD operating tokamaks. Total neutron yield is measured with 235 U and 238 U fission chambers and 3 He proportional counters in JT-60 Upgrade. The in situ calibration was performed by moving the 252 Cf neutron source toroidally through the JT-60 vacuum vessel. Detection efficiencies of three 235 U and two 3 He detectors were measured for 92 locations of the neutron point source in toroidal scans at two different major radii. The total detection efficiency for the torus neutron source was obtained by averaging the point efficiencies over the whole toroidal angle. The uncertainty of the resulting absolute plasma neutron source calibration is estimated to be ± 10%. (author)

  11. Rigid-flexible coupling dynamics of three-dimensional hub-beams system

    International Nuclear Information System (INIS)

    Liu Jinyang; Lu Hao

    2007-01-01

    In the previous research of the coupling dynamics of a hub-beam system, coupling between the rotational motion of hub and the torsion deformation of beam is not taken into account since the system undergoes planar motion. Due to the small longitudinal deformation, coupling between the rotational motion of hub and the longitudinal deformation of beam is also neglected. In this paper, rigid-flexible coupling dynamics is extended to a hub-beams system with three-dimensional large overall motion. Not only coupling between the large overall motion and the bending deformation, but also coupling between the large overall motion and the torsional deformation are taken into account. In case of temperature increase, the longitudinal deformation caused by the thermal expansion is significant, such that coupling between the large overall motion and the longitudinal deformation is also investigated. Combining the characteristics of the hybrid coordinate formulation and the absolute nodal coordinate formulation, the system generalized coordinates include the relative nodal displacement and the slope of each beam element with respect to the body-fixed frame of the hub, and the variables related to the spatial large overall motion of the hub and beams. Based on precise strain-displacement relation, the geometric stiffening effect is taken into account, and the rigid-flexible coupling dynamic equations are derived using velocity variational principle. Finite element method is employed for discretization. Simulation of a hub-beams system is used to show the coupling effect between the large overall motion and the torsional deformation as well as the longitudinal deformation. Furthermore, conservation of energy in case of free motion is shown to verify the formulation

  12. Design optimization of JT-60SU for steady-state advanced operation

    International Nuclear Information System (INIS)

    Ushigusa, K.; Kurita, G.; Toyoshima, N.

    2001-01-01

    Design optimization of JT-60SU has been done for a steady-state advanced operation. A transport code simulation indicates that a fully non-inductive reversed shear plasmas with fractions of 70% of the bootstrap current and 30% of beam driven current can be sustained for more than 1,000s without any additional control. Investigations have been progressed on MHD stability, vertical positional stability and dynamics of the vertical displacement events. Significant progress has been achieved in the R and D of Nb 3 Al superconducting wires, low induced activation material (Fe-Cr-Mn steel). A design improvement has been made in TF coils to reduce a local stress on radial disk. Dynamic behaviors of the tokamak machine have been analyzed at emergency events such as an earthquake. (author)

  13. 14 CFR 34.1 - Definitions.

    Science.gov (United States)

    2010-01-01

    .... Class T3 means all aircraft gas turbine engines of the JT3D model family. Class T8 means all aircraft gas turbine engines of the JT8D model family. Class TSS means all aircraft gas turbine engines... never been in service. Power setting means the power or thrust output of an engine in terms of...

  14. Temporal-varying failures of nodes in networks

    Science.gov (United States)

    Knight, Georgie; Cristadoro, Giampaolo; Altmann, Eduardo G.

    2015-08-01

    We consider networks in which random walkers are removed because of the failure of specific nodes. We interpret the rate of loss as a measure of the importance of nodes, a notion we denote as failure centrality. We show that the degree of the node is not sufficient to determine this measure and that, in a first approximation, the shortest loops through the node have to be taken into account. We propose approximations of the failure centrality which are valid for temporal-varying failures, and we dwell on the possibility of externally changing the relative importance of nodes in a given network by exploiting the interference between the loops of a node and the cycles of the temporal pattern of failures. In the limit of long failure cycles we show analytically that the escape in a node is larger than the one estimated from a stochastic failure with the same failure probability. We test our general formalism in two real-world networks (air-transportation and e-mail users) and show how communities lead to deviations from predictions for failures in hubs.

  15. Fixed-axis electric sail deployment dynamics analysis using hub-mounted momentum control

    Science.gov (United States)

    Fulton, JoAnna; Schaub, Hanspeter

    2018-03-01

    The deployment dynamics of a spin stabilized electric sail (E-sail) with a hub-mounted control actuator are investigated. Both radial and tangential deployment mechanisms are considered to take the electric sail from a post-launch stowed configuration to a fully deployed configuration. The tangential configuration assumes the multi-kilometer tethers are wound up on the exterior of the spacecraft hub, similar to yo-yo despinner configurations. The deployment speed is controlled through the hub rate. The radial deployment configuration assumes each tether is on its own spool. Here both the hub and spool rate are control variables. The sensitivity of the deployment behavior to E-sail length, maximum rate and tension parameters is investigated. A constant hub rate deployment is compared to a time varying hub rate that maintains a constant tether tension condition. The deployment time can be reduced by a factor of 2 or more by using a tension controlled deployment configuration.

  16. Manufacturing of central control system of 'JT-60' a plasma feasibility experiment device

    International Nuclear Information System (INIS)

    Kondo, Ikuo; Kimura, Toyoaki; Murai, Katsuji; Iba, Daizo; Takemaru, Koichi.

    1984-01-01

    For constructing a critical-plasma-experiment apparatus JT-60, it was necessary to develop a new control system which enables to operate safely and smoothly a large scale nuclear fusion apparatus and to carry out efficient experiment. For the purpose, the total system control facility composed of such controllers as CAMAC system, timing system and protective interlock panel with multi-computer system as the core was developed. This system generalizes, keeps watch on and controls the total facilities as the key point of the control system of JT-60, and allows flexible operation control corresponding to the diversified experimental projects. At the same time, it carries out the fast real-time control of high temperature, high density plasma. In this paper, the system constitution, function and the main contents of development of the total system control facility are reported. JT-60 is constructed to attain the critical plasma condition as the premise of nuclear fusion reactors and to scientifically verify controlled nuclear fusion. Plasma expe riment will be started in April, 1985. The real-time control of plasma for carrying out high beta operation is planned, intending to develop future economical practical reactors. (Kako, I.)

  17. Analyses of plasma parameter profiles in JT-60U

    Energy Technology Data Exchange (ETDEWEB)

    Shirai, Hiroshi; Shimizu, Katsuhiro; Hayashi, Nobuhiko [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment; Itakura, Hirofumi; Takase, Keizou [CSK Co. Ltd., Tokyo (Japan)

    2001-01-01

    The methods how diagnostics data are treated as the surface quantity of magnetic surface and processed to the profile data in the JT-60U plasmas are summarized. The MHD equilibrium obtained by solving Grad-Shafranov equation on the MHD equilibrium calculation and registration software FBEQU are saved shot by shot as a database. Various experimental plasma data measured at various geometrical positions on JT-60 are mapped onto the MHD equilibrium and treated as functions of the volume averaged minor radius {rho} on the experimental data time slice monitoring software SLICE. Experimental data are integrated and edited on SLICE. The experimental data measured as the line integral values are transformed by Able inversion. The mapped data are fitted to a functional form and saved to the profile database MAP-DB. SLICE can also read data from MAP-DB and redisplay and transform them. In addition, SLICE can generate the profile data TOKRD as run data for orbit following Monte-Carlo (OFMC) code, analyzer for current drive consistent with MHD equilibrium (ACCOME) code and tokamak predictive and interpretive code system (TOPICS). (author)

  18. Analyses of plasma parameter profiles in JT-60U

    International Nuclear Information System (INIS)

    Shirai, Hiroshi; Shimizu, Katsuhiro; Hayashi, Nobuhiko

    2001-01-01

    The methods how diagnostics data are treated as the surface quantity of magnetic surface and processed to the profile data in the JT-60U plasmas are summarized. The MHD equilibrium obtained by solving Grad-Shafranov equation on the MHD equilibrium calculation and registration software FBEQU are saved shot by shot as a database. Various experimental plasma data measured at various geometrical positions on JT-60 are mapped onto the MHD equilibrium and treated as functions of the volume averaged minor radius ρ on the experimental data time slice monitoring software SLICE. Experimental data are integrated and edited on SLICE. The experimental data measured as the line integral values are transformed by Able inversion. The mapped data are fitted to a functional form and saved to the profile database MAP-DB. SLICE can also read data from MAP-DB and redisplay and transform them. In addition, SLICE can generate the profile data TOKRD as run data for orbit following Monte-Carlo (OFMC) code, analyzer for current drive consistent with MHD equilibrium (ACCOME) code and tokamak predictive and interpretive code system (TOPICS). (author)

  19. Deuterated-decaborane using boronization on JT-60U

    Energy Technology Data Exchange (ETDEWEB)

    Yagyu, Jun-ichi; Arai, Takashi; Kaminaga, Atsushi; Miyata, Katsuyuki [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment; Arai, Masaru [Kaihatsu Denki Co., Ltd., Tokyo (Japan)

    2001-03-01

    In JT-60U, boronization using hydride-decaborane (B{sub 10}H{sub 14}) vaporization has been conducted for the first wall conditioning. Compared to other discharge cleaning (DC), boronization is claimed to be efficient in reduction of oxygen impurities and hydrogen recycling in plasma. However, there are some problems in reduction of hydrogen included in boron film and stabilization of DC glow discharge during the boronization. To solve these problems, a new boronization method using deuterated-decaborane (B{sub 10}D{sub 14}) was adopted instead of the conventional hydride-decaborane. As a result, hydrogen content in the boron film decreased clearly and discharge conditioning shots, for decreasing hydrogen content in plasmas, after the boronization were reduced to 1/10 in comparison to the conventional process. Furthermore, DC glow discharge became stable, with only helium carrier gas, and it was possible to save 30 hours in maximum of the time necessary to boronization. It is shown that the boronization using deuterated-decaborane is very efficient and effective method for the first wall conditioning. (author)

  20. Failure analysis of a helicopter's main rotor bearing

    International Nuclear Information System (INIS)

    Shahzad, M.; Qureshi, A.H.; Waqas, H.; Hussain, N.; Ali, N.

    2011-01-01

    Presented results report some of the findings of a detailed failure analysis carried out on a main rotor hub assembly, which had symptoms of burning and mechanical damage. The analysis suggests environmental degradation of the grease which causes pitting on bearing-balls. The consequent inefficient lubrication raises the temperature which leads to the smearing of cage material (brass) on the bearing-balls and ultimately causes the failure. The analysis has been supported by the microstructural studies, thermal analysis and micro-hardness testing performed on the affected main rotor bearing parts. (author)

  1. Development of a new discharge control system utilizing UNIX workstations and VME-bus systems for JT-60

    Energy Technology Data Exchange (ETDEWEB)

    Akasaka, Hiromi; Sueoka, Michiharu; Takano, Shoji; Totsuka, Toshiyuki; Yonekawa, Izuru; Kurihara, Kenichi; Kimura, Toyoaki [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    2002-01-01

    The JT-60 discharge control system, which had used HIDIC-80E 16 bit mini-computers and CAMAC systems since the start of JT-60 experiment in 1985, was renewed in March, 2001. The new system consists of a UNIX workstation and a VME-bus system, and features a distributed control system. The workstation performs message communication with a VME-bus system and controllers of JT-60 sub-systems and processing for discharge control because of its flexibility to construction of a new network and modifications of software. The VME-bus system performs discharge sequence control because it is suitable for fast real time control and flexible to the hardware extension. The replacement has improved the control function and reliability of the discharge control system and also has provided sufficient performance necessary for future modifications of JT-60. The new system has been running successfully since April 2001. The data acquisition speed was confirmed to be twice faster than the previous one. This report describes major functions of the discharge control system, technical ideas for developing the system and results of the initial operation in detail. (author)

  2. ARRA: Reconfiguring Power Systems to Minimize Cascading Failures - Models and Algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Dobson, Ian [Iowa State University; Hiskens, Ian [Unversity of Michigan; Linderoth, Jeffrey [University of Wisconsin-Madison; Wright, Stephen [University of Wisconsin-Madison

    2013-12-16

    Building on models of electrical power systems, and on powerful mathematical techniques including optimization, model predictive control, and simluation, this project investigated important issues related to the stable operation of power grids. A topic of particular focus was cascading failures of the power grid: simulation, quantification, mitigation, and control. We also analyzed the vulnerability of networks to component failures, and the design of networks that are responsive to and robust to such failures. Numerous other related topics were investigated, including energy hubs and cascading stall of induction machines

  3. Managing effective and efficient hub operations : a study of ground time management

    NARCIS (Netherlands)

    Yunita, Theresia

    2009-01-01

    This Logistics Design Project was carried out at KLM Aircraft Services (AS), from February 2008 - April 2009. The project focuses on ideal description of KLM operational controls for daily executions at the hub and within the AS processes. The daily execution at the hub is managed by the Hub Control

  4. Weight Estimate and Centers of Gravity for JT-11 Nuclear Conversion Study

    International Nuclear Information System (INIS)

    Manning, R. W.

    1958-01-01

    Weight estimates and centers of gravity for the JT-11 nuclear conversion study are tabulated. Included in the radiator section are: diffuser, shrouds, supports, radiator, liquid metal, shafting and casing.

  5. Multiaxial brittle failure of a 3D carbon-carbon composite

    International Nuclear Information System (INIS)

    Davy, Catherine

    2001-01-01

    Several industrial equipments, for example in aeronautics, civil or military nuclear applications, imply multi-axially loaded brittle materials for which reliable failure models are needed. In that context, our study focuses on a 3D carbon-carbon composite submitted in service to a triaxial strain state along its orthotropy axes. A failure criterion based on a bibliographical analysis is identified thanks to uniaxial tensile tests, and validated through an original multiaxial experiment. The scatter on its failure characteristics is also identified. (author) [fr

  6. Effects of pressure profile and plasma shaping on the n=1 internal kink mode in JT-60/JT-60U pellet fuelled plasmas

    International Nuclear Information System (INIS)

    Ozeki, Takahisa; Azumi, Masafumi

    1990-10-01

    The stability of the n=1 internal kink mode in a tokamak is numerically analyzed for plasmas with a centrally peaked pressure profile. These studies are carried out with the strongly peaked pressure inside the q=1 surface, which is based on the experimentally observed plasmas by means of injections of hydrogen-ice pellets in JT-60 tokamak. The effects of peaked pressure and shaping, i.e., elongation and triangularity, are also studied for JT-60U tokamak. The plasma with the strongly peaked pressure profile has higher critical value of poloidal beta defined within the q=1 surface than that with a parabolic pressure profile. Though the beta limit reduces with the increase of the elongation, the plasma with the peaked pressure profile has larger improvement due to the triangularity than that with the parabolic pressure profile. To access the second stability of the n=1 internal kink mode, the plasma with a flat pressure profile and the large minor radius of the q=1 surface is effective. (author)

  7. Optical design for divertor Thomson scattering system for JT-60SA

    International Nuclear Information System (INIS)

    Kajita, Shin; Enokuchi, Akito; Hatae, Takaki; Itami, Kiyoshi; Hamano, Takashi; Kado, Shinichiro; Ohno, Noriyasu; Takeyama, Norihide

    2014-01-01

    Highlights: •A detailed designing for collection optical system of divertor Thomson scattering system in JT-60SA is conducted. •The assessment of the density and temperature errors of the measurement system is conducted. •It is shown that the measurement could be done with the temperature error of 50% when the density was 10 20 m −3 . •The availability of the laser transmission mirrors for the measurement system is discussed. •Several guidelines to improve the measurement system are discussed. -- Abstract: Optical design for divertor Thomson scattering system in JT-60SA has been conducted. The measurement system will use a Nd:YAG laser at 1064 nm, and scattered photons are collected by a collection optical system. The collection optics consists of primary mirror, secondary mirror, relay optics, and fiber collection optics. The laser transmission mirror and collection optics were designed to be installed in a slender lower port of JT-60SA. The assessment of the measurement errors in temperature was conducted for the designed collection optical system. Because of spatial limitation, the solid angle from the measurement points would be small especially for the measurement points in high field side, and consequently, the temperature errors in the high field side would be considerably large. The effects of several improvements on the error are discussed. Moreover, an assessment for the in-vessel laser transmission metallic mirrors is conducted for the present design

  8. Vacuum pumping system for the JT-60 radio-frequency heating system

    International Nuclear Information System (INIS)

    Yokokura, Kenji; Ikeda, Yoshitaka; Imai, Tuyoshi; Suganuma, Kazuaki; Nagashima, Takashi

    1988-01-01

    The basic design requirements set up for the JT-60 radio-frequency heating system included: (1) rapid pumping of gas released upon application of a radio-frequency power to maintain the pressure in the launchers at 10 -2 - 10 -3 Pa or less, (2) incorporation of a gas analysis system that can operate under a strong field and high pressure (>10 -2 Pa) to permit remote controlled data collection and processing, and (3) low cost, multiple functions and high reliability. The vacuum pumping system, consisting of three units for low hybrid radio-frequency (LHRF) and one unit for ion cyclotron radio-frequency (ICRF), is connected to each launcher provided at the four ports of JT-60. The LHRF unit is composed of a main pump, an alumina joint for electrical insulation from the launcher, a metallic gate valve for isolation from the JT-60 vacuum region, and various vacuum gauges. Only a turbo-molecular pump is used for the ICRF system because a large-scale differential pumping is not required. A gas measuring system is incorporated which consists of a mass filter, personal computer, turbo-molecular pump, and variable flow valve equipped with an APG control. This system is designed to identify and make use of gas impurities released during the launcher aging process. The control system employed consists of a personal computer, interlock control board, data logger and other devices such as vacuum gages. (Nogami, K.)

  9. Hydrogen isotope behavior in the first wall of JT-60U after deuterium plasma operation

    International Nuclear Information System (INIS)

    Oya, Y.; Tanabe, T.; Oyaidzu, M.; Shibahara, T.; Sugiyama, K.; Yoshikawa, A.; Onishi, Y.; Hirohata, Y.; Ishimoto, Y.; Yagyu, J.; Arai, T.; Masaki, K.; Okuno, K.; Miya, N.; Tanaka, S.

    2007-01-01

    Retention of hydrogen isotopes in the carbon (isotropic graphite) first wall tiles of JT-60U was studied by secondary ion mass spectrometry and thermal desorption spectroscopy. The surface morphology and erosion/deposition profiles of the tiles were characterized using scanning electron microscope and X-ray photoelectron spectroscopy. The upper area is mainly eroded, while the bottom area of the inboard wall is dominated by deposition. In contrast to the divertor area, hydrogen isotope retention in the eroded wall area was generally larger than that in the deposition dominated area. Measured near surface concentrations of hydrogen isotopes in the wall tiles, as well as the D/H ratios, were a little higher than those in the divertor area. This indicates direct implantation of high-energy D from NBI into the first wall. The lower temperature of the first wall relative to the divertor tiles would reduce desorption and/or replacement of implanted D by subsequent D or H impingement

  10. Development of TiC coated wall materials for JT-60

    International Nuclear Information System (INIS)

    Abe, T.; Murakami, Y.; Obara, K.; Hiroki, S.; Nakamura, K.; Inagawa, K.

    1985-01-01

    Development of titanium carbide (TiC, 20 μm thick) coated wall materials has been carried out for JT-60. Application of TiC coatings onto molybdenum and Inconel 625 substrates requires a deposition temperature below 950 0 C and 600 0 C respectively, because recrystallization of molybdenum and age hardening of Inconel 625 occur above these temperatures. Through this process of coating we develop a new type plasma CVD(TP-CVD method) for molybdenum and a new type PVD(HCD-ARE method) for Inconel 625 which could successfully reduce the deposition temperature to 900 0 C and 500 0 C, respectively. The TiC coated wall samples were characterized by AES, ESCA, X-ray diffractometer, EPMA, SEM, metalography, tensile tests, thermal shock tests, and other techniques. As a result of the above measurements, it was demonstrated that the characteristics of those TiC coated walls satisfy the requirements arising from JT-60 operation conditions. (orig.)

  11. Mechanical Design, Analysis, and Testing of a Two-Bladed Wind Turbine Hub

    Energy Technology Data Exchange (ETDEWEB)

    Cotrell, J.

    2002-06-01

    Researchers at the National Wind Technology Center (NWTC) in Golden, Colorado, began performing the Unsteady Aerodynamics Experiment in 1993 to better understand the unsteady aerodynamics and structural responses of horizontal-axis wind turbines. The experiment consists of an extensively instrumented, downwind, three-bladed, 20-kilowatt wind turbine. In May 1995, I received a request from the NWTC to design a two-bladed hub for the experiment. For my thesis, I present the results of the mechanical design, analysis, and testing of the hub. The hub I designed is unique because it runs in rigid, teetering, or independent blade-flapping modes. In addition, the design is unusual because it uses two servomotors to pitch the blades independently. These features are used to investigate new load reduction, noise reduction, blade pitch optimization, and yaw control techniques for two-bladed turbines. I used a methodology by G. Phal and W. Bietz to design the hub. The hub meets all the performance specifications except that it achieves only 90% of the specified teeter range. In my thesis, I focus on the analysis and testing of the hub body. I performed solid-mechanics calculations, ran a finite-element analysis simulation, and experimentally investigated the structural integrity of the hub body.

  12. The H-mode pedestal, ELMs and TF ripple effects in JT-60U/JET dimensionless identity experiments

    International Nuclear Information System (INIS)

    Saibene, G.; Oyama, N.; Loennroth, J.; Andrew, Y.; Luna, E. de la; Giroud, C.; Huysmans, G.T.A.; Kamada, Y.; Kempenaars, M.A.H.; Loarte, A.; Donald, D. Mc; Nave, M.M.F.; Meiggs, A.; Parail, V.; Sartori, R.; Sharapov, S.; Stober, J.; Suzuki, T.; Takechi, M.; Toi, K.; Urano, H.

    2007-01-01

    This paper summarizes results of dimensionless identity experiments in JT-60U and JET, aimed at the comparison of the H-mode pedestal and ELM behaviour in the two devices. Given their similar size, dimensionless matched plasmas are also similar in their dimensional parameters (in particular, the plasma minor radius a is the same in JET and JT-60U). Power and density scans were carried out at two values of I p , providing a q scan (q 95 = 3.1 and 5.1) with fixed (and matched) toroidal field. Contrary to initial expectations, a dimensionless match between the two devices was quite difficult to achieve. In general, p ped in JT-60U is lower than in JET and, at low q, the pedestal pressure of JT-60U with a Type I ELMy edge is matched in JET only in the Type III ELM regime. At q 95 = 5.1, a dimensionless match in ρ*, ν* and β p,ped is obtained with Type I ELMs, but only with low power JET H-modes. These results motivated a closer investigation of experimental conditions in the two devices, to identify possible 'hidden' physics that prevents obtaining a good match of pedestal values over a large range of plasmas parameters. Ripple-induced ion losses of the medium bore plasma used in JT-60U for the similarity experiments are identified as the main difference with JET. The magnitude of the JT-60U ripple losses is sufficient to induce counter-toroidal rotation in co-injected plasma. The influence of ripple losses was demonstrated at q 95 = 5.1: reducing ripple losses by ∼2 (from 4.3 to 1.9 MW) by replacing positive with negative neutral beam injection at approximately constant P in resulted in an increased p ped in JT-60U, providing a good match to full power JET H-modes. At the same time, the counter-toroidal rotation decreased. Physics mechanisms relating ripple losses to pedestal performance are not yet identified, and the possible role of velocity shear in the pedestal stability, as well as the possible influence of ripple on thermal ion transport are briefly

  13. SUN HUB – ENERGY HUB FOR OUTDOOR TABLES

    DEFF Research Database (Denmark)

    Poulsen, Peter Behrensdorff; Benatto, Gisele Alves dos Reis; Riedel, Nicholas

    2017-01-01

    connections, providing opportunity to stream music via Bluetooth and play it from a handheld device to the table and lastly to provide LED lighting on the table during the dark hours. 3 prototypes of the system was built and tested at the Roskilde Festival 2017. Electrical logger units were built into the 3...... on festivals where people camps for several days it can be hard to have your portable units charged. In this this work we report a solar powered hub, as an add-on to a table in the urban environment for charging mobile phones and tablets and other handheld devices through USBs, charging laptops through AC...

  14. Multiple Hub Network Choice in the Liberalized European Market

    Science.gov (United States)

    Berechman, Joseph; deWit, Jaap

    1997-01-01

    A key question that so far has received relatively little attention in the germane literature is that of the changes at various airports as a result of the EU liberalization policies. That is, presently, most major European airports still benefit from the so-called home-carrier phenomenon where the country's publicly or semi-publicly owned carrier uses the country's main airport as its gateway hub and, consequently, the home-carrier is also the principal user of this airport (in terms of proportion of total aircraft movements, number of passengers transported, connections, slots ownership, etc.). The country's main airport has substantially benefited from these monopoly conditions of airline captivity, strongly determined by the bilateral system of international air transport regulation. Therefore, European major airports were used to operate in essentially different markets, compared to the increasingly competitive markets of their home based carriers. This partly explains relative stability of transport volumes and financial results of European major airports compared to the relatively volatile financial results of most European national airlines. However, the liberalization of European aviation is likely to change this situation. Market access is open now to all community carriers, i.e. carriers with majority ownership and effective control in the hands of EU citizens. Ticket prices are free, governments can only intervene in case of dumping or excessive pricing. A community airline can choose its seat in any of the 15 member states. Licensing procedures are harmonized between member states. In the last few months community carriers have had unrestricted route access within the EU. Most probably this development will be extended to countries inside and outside Europe. Last year the European Commission got the mandate to start negotiations with 10 other European countries. In the meantime the EC has also started negotiations with the USA on so-called soft rights

  15. Diagnostic planning in JT-60 project

    International Nuclear Information System (INIS)

    Matoba, Tohru; Suzuki, Yasuo; Funahashi, Akimasa; Itagaki, Tokiyoshi

    1977-08-01

    The diagnostic plans of JT-60 were made along with design of the main machine. Basic requirements of the diagnostic program are (1) multiple measurement of respective plasma parameters, (2) efficient usage of the discharge, (3) capable data acquisition system, (4) high reliability of the diagnostic equipments, and (5) systematic development of new diagnostic techniques. Dimensions of the diagnostic ports were determined in detailed design of the vacuum vessel, anticipating the possible diagnostic methods. The proposed diagnostic systems and the plans are shown in table and figures respectively. Problems in the diagnostics are also described. (auth.)

  16. Predicting highly-connected hubs in protein interaction networks by QSAR and biological data descriptors

    Science.gov (United States)

    Hsing, Michael; Byler, Kendall; Cherkasov, Artem

    2009-01-01

    Hub proteins (those engaged in most physical interactions in a protein interaction network (PIN) have recently gained much research interest due to their essential role in mediating cellular processes and their potential therapeutic value. It is straightforward to identify hubs if the underlying PIN is experimentally determined; however, theoretical hub prediction remains a very challenging task, as physicochemical properties that differentiate hubs from less connected proteins remain mostly uncharacterized. To adequately distinguish hubs from non-hub proteins we have utilized over 1300 protein descriptors, some of which represent QSAR (quantitative structure-activity relationship) parameters, and some reflect sequence-derived characteristics of proteins including domain composition and functional annotations. Those protein descriptors, together with available protein interaction data have been processed by a machine learning method (boosting trees) and resulted in the development of hub classifiers that are capable of predicting highly interacting proteins for four model organisms: Escherichia coli, Saccharomyces cerevisiae, Drosophila melanogaster and Homo sapiens. More importantly, through the analyses of the most relevant protein descriptors, we are able to demonstrate that hub proteins not only share certain common physicochemical and structural characteristics that make them different from non-hub counterparts, but they also exhibit species-specific characteristics that should be taken into account when analyzing different PINs. The developed prediction models can be used for determining highly interacting proteins in the four studied species to assist future proteomics experiments and PIN analyses. Availability The source code and executable program of the hub classifier are available for download at: http://www.cnbi2.ca/hub-analysis/ PMID:20198194

  17. A Dynamic Calibration Method for Experimental and Analytical Hub Load Comparison

    Science.gov (United States)

    2017-03-01

    computed at various pitch angles through changes in actuator length. The linear spring stiffness was estimated by using the internal volume of the...Vehicle Technology Directorate Mechanics Division (ATTN: RDRL-VTM) Aberdeen Proving Ground, MD 21005-5066 8. PERFORMING ORGANIZATION REPORT NUMBER...Finally, the balance loads are not only induced by the rotor hub loads, but also by loads transmitted via the pitch links to the swashplate. Thus

  18. Microfluidic hubs, systems, and methods for interface fluidic modules

    Science.gov (United States)

    Bartsch, Michael S; Claudnic, Mark R; Kim, Hanyoup; Patel, Kamlesh D; Renzi, Ronald F; Van De Vreugde, James L

    2015-01-27

    Embodiments of microfluidic hubs and systems are described that may be used to connect fluidic modules. A space between surfaces may be set by fixtures described herein. In some examples a fixture may set substrate-to-substrate spacing based on a distance between registration surfaces on which the respective substrates rest. Fluidic interfaces are described, including examples where fluid conduits (e.g. capillaries) extend into the fixture to the space between surfaces. Droplets of fluid may be introduced to and/or removed from microfluidic hubs described herein, and fluid actuators may be used to move droplets within the space between surfaces. Continuous flow modules may be integrated with the hubs in some examples.

  19. Development of a pellet cutting and loading device for the JT-60 repetitive pellet injector

    International Nuclear Information System (INIS)

    Hiratsuka, Hajime; Ichige, Hisashi; Kizu, Kaname; Iwahashi, Takaaki; Honda, Masao

    2001-03-01

    In JT-60, a pellet injector that repetitively injects deuterium pellets is under development to supply fuel to high temperature plasmas and sustain high-density plasmas. The pellet injector generates cubic pellets and accelerates them with a straight-arm rotor by centrifugal force. In this acceleration method, it is important to supply pellets reliably and stably, to prevent pellet orbits from disordering and to stabilize the launching direction. To achieve higher performance of the injector, a pellet cutting and loading device that cuts a deuterium ice rod into cubic pellets and loads them to the pellet injector successively and stably has been developed. The pellet cutting and loading device can cut a deuterium ice rod produced at low temperature of -8 Pam 3 /s, cutting time of <3 ms, cutting frequency of 1-20 Hz and cutter stroke of 2.5 mm were confirmed in the device test. In the operation test after assembling this device to the centrifugal pellet injector, the operational performance of pellet injection frequency of ∼10 Hz, pellet speed of ∼690 m/s and pellet injection duration time of ∼3.5 s was achieved. Thus, the development of the pellet cutting and loading device contributed to the upgrade of the JT-60 pellet injector. (author)

  20. North West Surrey's locality hubs - delivering integrated care

    OpenAIRE

    Compton, Lisa; Wilkinson, Peter; Lawn, Liz

    2017-01-01

    Introduction: North West Surrey CCG (NWSCCG) is establishing Locality Hubs – physical buildings offering a fully integrated GP-led, multi-disciplinary ‘one-stop-shop’ services in the community for a defined cohort of frail elderly patients with multiple core morbidities. Hubs will ultimately deliver proactive and reactive care, available 24 hours a day, 365 days a year.The key drivers are;Ageing population, people living longer & more people living with chronic conditionsCost & demand...

  1. Quench propagation and quench detection in the TF system of JT-60SA

    International Nuclear Information System (INIS)

    Lacroix, Benoit; Duchateau, Jean-Luc; Meuris, Chantal; Ciazynski, Daniel; Nicollet, Sylvie; Zani, Louis; Polli, Gian-Mario

    2013-01-01

    Highlights: • The JT-60SA primary quench detection system will be based on voltage measurements. • The early quench propagation was studied in the JT-60SA TF conductor. • The impact of the conductor jacket on the hot spot criterion was quantified. • The detection parameters were investigated for different quench initiations. -- Abstract: In the framework of the JT-60SA project, France and Italy will provide to JAEA 18 Toroidal Field (TF) coils including NbTi cable-in-conduit conductors. During the tokamak operation, these coils could experience a quench, an incidental event corresponding to the irreversible transition from superconducting state to normal resistive state. Starting from a localized disturbance, the normal zone propagates along the conductor and dissipates a large energy due to Joule heating, which can cause irreversible damages. The detection has to be fast enough (a few seconds) to trigger the current discharge, so as to dump the stored magnetic energy into an external resistor. The JT-60SA primary quench detection system will be based on voltage measurements, which are the most rapid technology. The features of the detection system must be adjusted so as to detect the most probable quenches, while avoiding inopportune fast safety discharges. This requires a reliable simulation of the early quench propagation, performed in this study with the Gandalf code. The conductor temperature reached during the current discharge must be kept under a maximal value, according to the hot spot criterion. In the present study, a hot spot criterion temperature of 150 K was taken into account and the role of each conductor component (strands, helium and conduit) was analyzed. The detection parameters were then investigated for different hypotheses regarding the quench initiation

  2. Development of the centrifugal pellet injector for JT-60U

    Energy Technology Data Exchange (ETDEWEB)

    Kizu, Kaname; Hiratsuka, Hajime; Ichige, Hisashi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

    2001-03-01

    For core fueling of JT-60U plasmas, a repetitive pellet injector which centrifugally accelerates D{sub 2} cubic pellets using a straight rod has been developed. This centrifugal pellet injector can eject trains of up to 40 cubic pellets at frequencies of 1-10 Hz and velocities of 0.3-1.0 km/s. The average pellet mass is 3.6x10{sup 20} atoms/pellet below 0.7 m/s. Key techniques for the development were a mesh structured acceleration component for removing gas sublimated from the pellet and a funnel with an appropriate angle connected just behind the acceleration chamber for introducing the pellet to plasma without destruction. Using the mesh structured components, the horizontal angular distribution of pellets ejected became narrow, because irregular pellet motion caused by sublimated gas was reduced. To investigate the performance of the injector, pellet injection experiments from the low magnetic field side (LFS) were conducted using ohmic heating plasmas. Central fueling and enhanced fueling rate have been observed. D{alpha} intensity around the divertor region was reduced in a pellet injection plasma compared to gas puffing, indicating low recycling rate was maintained with the pellet injection. (author)

  3. Characteristics of halo current in JT-60U

    International Nuclear Information System (INIS)

    Neyatani, Y.; Nakamura, Y.; Yoshino, R.; Hatae, T.

    1999-01-01

    Halo currents and their toroidal peaking factor (TPF) have been measured in JT-60U by Rogowski coil type halo current sensors. The electron temperature in the halo region was around 10 eV at 1 ms before the timing of the maximum halo current. The maximum TPF*I h /I p0 was 0.52 in the operational range of I p = 0.7 ∼ 1.8 MA, B T = 2.2 ∼ 3.5 T, including ITER design parameters of κ > 1.6 and q 95 = 3, which was lower than that of the maximum value of ITER data base (0.75). The magnitude of halo currents tended to decrease with the increase in stored energy just before the energy quench and with the line integrated electron density at the time of the maximum halo current. A termination technique in which the current channel remains stationary was useful to avoid halo current generation. Intense neon gas puffing during the VDE was effective for reducing the halo currents. (author)

  4. Characteristics of halo current in JT-60U

    International Nuclear Information System (INIS)

    Neyatani, Y.; Nakamura, Y.; Yoshino, R.; Hatae, T.

    2001-01-01

    Halo currents and their toroidal peaking factor (TPF) have been measured in JT-60U by Rogowski coil type halo current sensors. The electron temperature in the halo region was around 10 eV at 1 ms before the timing of the maximum halo current. The maximum TPF *I h /I p0 was 0.52 in the operational range of I p =0.7∼1.8MA, B T =2.2∼3.5T, including ITER design parameters of κ>1.6 and q 95 =3, which was lower than that of the maximum value of ITER data base (0.75). The magnitude of halo currents tended to decrease with the increase in stored energy just before the energy quench and with the line integrated electron density at the time of the maximum halo current. A termination technique in which the current channel remains stationary was useful to avoid halo current generation. Intense neon gas puffing during the VDE was effective for reducing the halo currents. (author)

  5. DigitalHub: A Repository Focused on the Future.

    Science.gov (United States)

    Ilik, Violeta; Hebal, Piotr; Olson, Anton; Wishnetsky, Susan; Pastva, Joelen; Kubilius, Ramune; Shank, Jonathan; Gutzman, Karen; Chung, Margarita; Holmes, Kristi

    2018-01-01

    The DigitalHub scholarly repository was developed and launched at the Galter Health Sciences Library for the Feinberg School of Medicine and the greater Northwestern Medicine community. The repository was designed to allow scholars the ability to create, share, and preserve a range of citable digital outputs. This article traces the evolution of DigitalHub's development and engagement activities, highlighting project challenges, innovations, success stories, and the team-based approach that was employed to successfully achieve project goals.

  6. Effect of tensile properties on time-dependent C(t) and J(t) integrals in elastic-plastic-creep FE analysis

    International Nuclear Information System (INIS)

    Lee, So-Dam; Lee, Han-Sang; Kim, Yun-Jae; Ainsworth, Robert A.; Dean, David W.

    2016-01-01

    This technical note presents the effect of elastic-plastic properties on calculated time-dependent C(t) and J(t) values. This is investigated via systematic elastic-plastic-creep finite element (FE) analysis. Three different stress-strain curves are used, having essentially the same plastic properties at large strains but different tensile data near the 0.2% proof (yield) strength. It is found that the plastic property in stress-strain curve affects the FE C(t) values only at short times (within approximately 20% of the redistribution time). The plastic property affects the initial J values at time t = 0 but not the rate of change of J(t) with time. - Highlights: • The effect of elastic-plastic properties on calculated time-dependent C(t) and J(t) values is presented via FE analysis. • The plastic property affects the FE C(t) values only at short times up to ∼20% of the redistribution time. • The plastic property affects the initial J values at time t = 0 but not the rate of change of J(t) with time.

  7. 8 CFR 208.10 - Failure to appear at an interview before an asylum officer or failure to follow requirements for...

    Science.gov (United States)

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Failure to appear at an interview before an... WITHHOLDING OF REMOVAL Asylum and Withholding of Removal § 208.10 Failure to appear at an interview before an... scheduled interview without prior authorization may result in dismissal of the application or waiver of the...

  8. Incremental Optimization of Hub and Spoke Network for the Spokes’ Numbers and Flow

    Directory of Open Access Journals (Sweden)

    Yanfeng Wang

    2015-01-01

    Full Text Available Hub and spoke network problem is solved as part of a strategic decision making process which may have a profound effect on the future of enterprises. In view of the existing network structure, as time goes on, the number of spokes and the flow change because of different sources of uncertainty. Hence, the incremental optimization of hub and spoke network problem is considered in this paper, and the policy makers should adopt a series of strategies to cope with the change, such as setting up new hubs, adjusting the capacity level of original hubs, or closing some original hubs. The objective is to minimize the total cost, which includes the setup costs for the new hubs, the closure costs, and the adjustment costs for the original hubs as well as the flow routing costs. Two mixed-integer linear programming formulations are proposed and analyzed for this problem. China Deppon Logistics as an example is performed to present computational analysis, and we analyze the changes in the solutions driven by the number of spokes and the flow. The tests also allow an analysis to consider the effect of variation in parameters on network.

  9. Development of a VME and CAMAC based data acquisition and transfer system for JT-60 control

    International Nuclear Information System (INIS)

    Totsuka, Toshiyuki

    1993-08-01

    Development of a VME and CAMAC based data acquisition and transfer system for JT-60 Control is reported. The present data acquisition and transfer system in JT-60 control is basically composed of CAMAC devices. Since the system equipped with 16-bit microcomputers was manufactured more than ten years ago, the performance and program development environment of the system are apparently worse than those of modern 32-bit microcomputers. To improve these disadvantages, a new data acquisition and transfer system using VME-based 32-bit microcomputers and CAMAC drivers is under design. Corresponding to this design, a CAMAC handler, which runs on the microcomputer, for the VME based CAMAC driver was newly developed. Moreover, the functions of the driver and data transfer performance of the VME and CAMAC complex system were tested. The test results shown that the VME based microcomputer and CAMAC serial driver can be applied for the fast and reliable acquisition and transfer system for JT-60 control. (author)

  10. Magistritööd : [Olga Volossova jt.

    Index Scriptorium Estoniae

    2000-01-01

    20. sept. 2000 kaitseb TPÜ-s matemaatika magistritööde kaitsmisnõukogu ees Olga Volossova magistritööd "Liftingud q-mõõtuvates ruumides". 27. sept. kaitseb TPÜ-s sotsiaaltöö magistrinõukogu ees Eike Käsi magistritööd "Tööjuhendamine sotsiaaltöös" ja Maarika Pukk magistritööd "Koolieeliku elukeskkond lasteasutuses : Reggio-Emilia meetodi rakendamine Eestis"

  11. 8 CFR 240.68 - Failure to appear at an interview before an asylum officer or failure to follow requirements for...

    Science.gov (United States)

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Failure to appear at an interview before an... Removal Under Section 203 of Pub. L. 105-100 § 240.68 Failure to appear at an interview before an asylum... interview without prior authorization may result in dismissal of the application or waiver of the right to...

  12. Estimation of Freezing Point of Hydrocarbon and Hydrofluorocarbon Mixtures for Mixed Refrigerant jt Cryocooler

    Science.gov (United States)

    Hwang, G.; Lee, J.; Jeong, S.

    2010-04-01

    Estimating the freezing point of refrigerant is an essential part in designing an MR JT (Mixed refrigerant Joule-Thomson) cryocooler to prevent itself from clogging and to operate with stability. There were researches on estimating freezing point, but some of them resulted in the wrong prediction of clogging. In this paper, the freezing point of the MR is precisely estimated with caution of clogging. The solubility of HC (hydrocarbon) and HFC (hydrofluorocarbon) mixture components are obtained with their activity coefficients, which represent the molecular interaction among the components. The freezing points of the MR JT cryocooler are systematically investigated in the operating temperature range from 70 K to 90 K.

  13. Sci-Hub: What Librarians Should Know and Do about Article Piracy.

    Science.gov (United States)

    Hoy, Matthew B

    2017-01-01

    The high cost of journal articles has driven many researchers to turn to a new way of getting access: "pirate" article sites. Sci-Hub, the largest and best known of these sites, currently offers instant access to more than 58 million journal articles. Users attracted by the ease of use and breadth of the collection may not realize that these articles are often obtained using stolen credentials and downloading them may be illegal. This article will briefly describe Sci-Hub and how it works, the legal and ethical issues it raises, and the problems it may cause for librarians. Librarians should be aware of Sci-Hub and the ways it may change their patrons' expectations. They should also understand the risks Sci-Hub can pose to their patrons and their institutions.

  14. Zoning Districts - Volusia County HUB Zones

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — Historically Underutilized Business (HUB) Zones in Volusia County. Go to http://www.sba.gov/hubzone or contact the Department of Economic Development (386) 248-8048...

  15. Comparison of Failure Modes in 2-D and 3-D Woven Carbon Phenolic Systems

    Science.gov (United States)

    Rossman, Grant A.; Stackpoole, Mairead; Feldman, Jay; Venkatapathy, Ethiraj; Braun, Robert D.

    2013-01-01

    NASA Ames Research Center is developing Woven Thermal Protection System (WTPS) materials as a new class of heatshields for entry vehicles (Stackpoole). Currently, there are few options for ablative entry heatshield materials, none of which is ideally suited to the planetary probe missions currently of interest to NASA. While carbon phenolic was successfully used for the missions Pioneer Venus and Galileo (to Jupiter), the heritage constituents are no longer available. An alternate carbon phenolic would need to be qualified for probe missions, which is most efficient at heat fluxes greater than those currently of interest. Additional TPS materials such as Avcoat and PICA are not sufficiently robust for the heat fluxes required. As a result, there is a large TPS gap between the materials efficient at very high conditions (carbon phenolic) and those that are effective at low-moderate conditions (all others). Development of 3D Woven TPS is intended to fill this gap, targeting mid-density weaves that could with withstand mid-range heat fluxes between 1100 W/sq cm and 8000 W/sq cm (Venkatapathy (2012). Preliminary experimental studies have been performed to show the feasibility of WTPS as a future mid-range TPS material. One study performed in the mARC Jet Facility at NASA Ames Research Center characterized the performance of a 3D Woven TPS sample and compared it to 2D carbon phenolic samples at ply angles of 0deg, 23.5deg, and 90deg. Each sample contained similar compositions of phenolic and carbon fiber volume fractions for experimental consistency. The goal of this study was to compare the performance of the TPS materials by evaluating resulting recession and failure modes. After exposing both samples to similar heat flux and pressure conditions, the 2D carbon phenolic laminate was shown to experience significant delamination between layers and further pocketing underneath separated layers. The 3D Woven TPS sample did not experience the delamination or pocketing

  16. Core transport properties in JT-60U and JET identity plasmas

    NARCIS (Netherlands)

    Litaudon, X.; Sakamoto, Y.; de Vries, P. C.; Salmi, A.; Tala, T.; Angioni, C.; Benkadda, S.; Beurskens, M. N. A.; Bourdelle, C.; Brix, M.; Crombe, K.; Fujita, T.; Futatani, S.; Garbet, X.; Giroud, C.; Hawkes, N. C.; Hayashi, N.; Hoang, G. T.; Hogeweij, G. M. D.; Matsunaga, G.; Nakano, T.; Oyama, N.; Parail, V.; Shinohara, K.; Suzuki, T.; Takechi, M.; Takenaga, H.; Takizuka, T.; Urano, H.; Voitsekhovitch, I.; Yoshida, M.

    2011-01-01

    The paper compares the transport properties of a set of dimensionless identity experiments performed between JET and JT-60U in the advanced tokamak regime with internal transport barrier, ITB. These International Tokamak Physics Activity, ITPA, joint experiments were carried out with the same plasma

  17. Correlated network of networks enhances robustness against catastrophic failures.

    Science.gov (United States)

    Min, Byungjoon; Zheng, Muhua

    2018-01-01

    Networks in nature rarely function in isolation but instead interact with one another with a form of a network of networks (NoN). A network of networks with interdependency between distinct networks contains instability of abrupt collapse related to the global rule of activation. As a remedy of the collapse instability, here we investigate a model of correlated NoN. We find that the collapse instability can be removed when hubs provide the majority of interconnections and interconnections are convergent between hubs. Thus, our study identifies a stable structure of correlated NoN against catastrophic failures. Our result further suggests a plausible way to enhance network robustness by manipulating connection patterns, along with other methods such as controlling the state of node based on a local rule.

  18. City Hub : a cloud based IoT platform for Smart Cities

    OpenAIRE

    Lea, Rodger; Blackstock, Michael

    2014-01-01

    Cloud based Smart City hubs are an attractive approach to addressing some of the complex issues faced when deploying PaaS infrastructure for Smart Cities. In this paper we introduce the general notion of IoT hubs and then discusses our work to generalize our IoT hub as a Smart City PaaS. Two key issues are identified, support for hybrid public/private cloud and interoperability. We briefly describe our approach to these issues and discuss our experiences deploying two cloud-based Smart City h...

  19. Idea Hubs as Nexus of Collective Creativity in Digital Innovation

    DEFF Research Database (Denmark)

    Ciriello, Raffaele; Richter, Alexander

    2015-01-01

    Digital innovation radically transforms the nature of corporate innovation practices, implying a growing need for deeper understanding its origins and outcomes. In this paper, we conceptualize the focal points of social networking in digital innovation as idea hubs. We focus our analysis...... on instances of idea hubs in two multinational European software companies, where we conducted a case study over a two-year period, and collected data in form of interviews, digital documents, and participant observations. In doing so, we identify a set of social networking practices in which idea hubs serve...... of digital artifacts individuals can choose from, offline interaction still plays a major role in facilitating digital innovation....

  20. Sharing environmental models: An Approach using GitHub repositories and Web Processing Services

    Science.gov (United States)

    Stasch, Christoph; Nuest, Daniel; Pross, Benjamin

    2016-04-01

    accordingly. The admin tool of the 52°North WPS was extended to support automated retrieval and deployment of computational models from GitHub repositories. Once the R code is available in the GitHub repo, the contained process can be easily deployed and executed by simply defining the GitHub repository URL in the WPS admin tool. We illustrate the usage of the approach by sharing and running a model for land use system archetypes developed by the Helmholtz Centre for Environmental Research (UFZ, see Vaclavik et al.). The original R code was extended and published in the 52°North WPS using both, public and non-public datasets (Nüst et al., see also https://github.com/52North/glues-wps). Hosting the analysis in a Git repository now allows WPS administrators, client developers, and modelers to easily work together on new versions or completely new web processes using the powerful GitHub collaboration platform. References: Hinz, M. et. al. (2013): Spatial Statistics on the Geospatial Web. In: The 16th AGILE International Conference on Geographic Information Science, Short Papers. http://www.agile-online.org/Conference_Paper/CDs/agile_2013/Short_Papers/SP_S3.1_Hinz.pdf Nüst, D. et. al.: (2015): Open and reproducible global land use classification. In: EGU General Assembly Conference Abstracts . Vol. 17. European Geophysical Union, 2015, p. 9125, http://meetingorganizer.copernicus. org/EGU2015/EGU2015- 9125.pdf Vaclavik, T., et. al. (2013): Mapping global land system archetypes. Global Environmental Change 23(6): 1637-1647. Online available: October 9, 2013, DOI: 10.1016/j.gloenvcha.2013.09.004

  1. 3. Laser Thomson scattering by plasmas. 3.2. Applications of incoherent Thomson scattering. 3.2.2. Incoherent Thomson scattering systems for JT-60U and JFT-2M

    International Nuclear Information System (INIS)

    Hatae, Takaki; Yoshida, Hidetoshi; Naito, Osamu; Yamauchi, Toshihiko

    2000-01-01

    Development of Thomson scattering diagnostics for the JT-60U and JFT-2M Tokamaks are described. Two Thomson scattering systems have been installed on JT-60U. The first system uses two ruby lasers (10 J, 0.25 Hz) and measures electron temperature (T e ) and density (n e ) profiles of 60 spatial points with high spatial resolution (8 mm). The second system uses a YAG laser (2 J, 30 Hz) and measures time evolution of T e and n e profiles with 15 spatial points. On JFT-2M, a TV Thomson Scattering system (TVTS) has been installed and measures at 81 spatial points with high spatial resolution (8.6 mm). These systems have provided not only profiles of all over the plasma, but successfully measured local structures to study various physics issues; e.g. H-mode edge pedestal, internal transport barrier, local MHD event. (author)

  2. A new workstation based man/machine interface system for the JT-60 Upgrade

    International Nuclear Information System (INIS)

    Yonekawa, I.; Shimono, M.; Totsuka, T.; Yamagishi, K.

    1992-01-01

    Development of a new man/machine interface system was stimulated by the requirements of making the JT-60 operator interface more 'friendly' on the basis of the past five-year operational experience. Eleven Sun/3 workstations and their supervisory mini-computer HIDIC V90/45 are connected through the standard network; Ethernet. The network is also connected to the existing 'ZENKEI' mini-computer system through the shared memory on the HIDIC V90/45 mini-computer. Improved software, such as automatic setting of the discharge conditions, consistency check among the related parameters and easy operation for discharge result data display, offered the 'user-friendly' environments. This new man/machine interface system leads to the efficient operation of the JT-60. (author)

  3. Connectome hubs at resting state in children and adolescents: Reproducibility and psychopathological correlation

    Directory of Open Access Journals (Sweden)

    João Ricardo Sato

    2016-08-01

    Full Text Available Functional brain hubs are key integrative regions in brain networks. Recently, brain hubs identified through resting-state fMRI have emerged as interesting targets to increase understanding of the relationships between large-scale functional networks and psychopathology. However, few studies have directly addressed the replicability and consistency of the hub regions identified and their association with symptoms. Here, we used the eigenvector centrality (EVC measure obtained from graph analysis of two large, independent population-based samples of children and adolescents (7–15 years old; total N = 652; 341 subjects for site 1 and 311 for site 2 to evaluate the replicability of hub identification. Subsequently, we tested the association between replicable hub regions and psychiatric symptoms. We identified a set of hubs consisting of the anterior medial prefrontal cortex and inferior parietal lobule/intraparietal sulcus (IPL/IPS. Moreover, lower EVC values in the right IPS were associated with psychiatric symptoms in both samples. Thus, low centrality of the IPS was a replicable sign of potential vulnerability to mental disorders in children. The identification of critical and replicable hubs in functional cortical networks in children and adolescents can foster understanding of the mechanisms underlying mental disorders.

  4. Development of fast charge exchange recombination spectroscopy by using interference filter method in JT-60U

    International Nuclear Information System (INIS)

    Kobayashi, Shinji; Sakasai, Akira; Koide, Yoshihiko; Sakamoto, Yoshiteru; Kamada, Yutaka; Hatae, Takaki; Oyama, Naoyuki; Miura, Yukitoshi

    2003-01-01

    Recent developments and results of fast charge exchange recombination spectroscopy (CXRS) using interference filter method are reported. In order to measure the rapid change of the ion temperature and rotation velocity under collapse or transition phenomena with high-time resolution, two types of interference filter systems were applied to the CXRS diagnostics on the JT-60U Tokamak. One can determine the Doppler broadening and Doppler shift of the CXR emission using three interference filters having slightly different center wavelengths. A rapid estimation method of the temperature ad rotation velocity without non-linear least square fitting is presented. The modification of the three-filters system enables us to improve the minimum time resolution up to 0.8 ms, which is better than that of 16.7 ms for the conventional CXRS system using the CCD detector in JT-60U. The other system having seven wavelength channels is newly fabricated to crosscheck the results obtained by the three-filters assembly, that is, to verify that the CXR emission forms a Gaussian profile under collapse phenomena. In a H-mode discharge having giant edge localized modes, the results obtained by the two systems are compared. The applicability of the three-filters system to the measurement of rapid changes in temperature and rotation velocity is demonstrated. (author)

  5. Ion transport analysis of a high beta-poloidal JT-60U discharge

    International Nuclear Information System (INIS)

    Horton, W.; Tajima, T.; Dong, J.-Q.; Kim, J.-Y.; Kishimoto, Y.

    1997-01-01

    The high beta-poloidal discharge number 17110 in JT-60U (JT-60 Team, IAEA, Vienna, 1993) that developes an internal transport barrier is analysed for the transport of ion energy and momentum. First, the classical ion temperature gradient stability properties are calculated in the absence of sheared plasma flows to establish the L-mode transport level prior to the emergence of the transport barrier. Then the evolving toroidal and poloidal velocity profiles reported by Koide et al (1994 Phys. Rev. Lett. 72 3662) are used to show how the sheared mass flows control the stability and transport. Coupled energy-momentum transport equations predict the creation of a transport barrier. The balance of the steep ion temperature gradient against the magnetic shear and sheared mass flow is calculated for the profiles in the 17110 discharge. (Author)

  6. Radioimmunoassay of [8-D-arginine] deamino-vasopressin (dDAVP)

    International Nuclear Information System (INIS)

    Slaninova, J.; Barth, T.

    1978-01-01

    Specific antibodies to [8-D-arginine] deamino-vasopressin (dDAVP) were prepared by immunizing pigs with the conjugate of [8-D-arginine] vasopressin (DVAP) and rabbit immunoglobulin. The specificity of the antibodies was studied by comparing their cross-reactivity with 20 analogues of neurohypophysial hormones. The sensitivity of the developed radioimmunoassay was 30 pg/ml. (authors)

  7. A Hub Matrix Theory and Applications to Wireless Communications

    Directory of Open Access Journals (Sweden)

    Kung HT

    2007-01-01

    Full Text Available This paper considers communications and network systems whose properties are characterized by the gaps of the leading eigenvalues of for a matrix . It is shown that a sufficient and necessary condition for a large eigen-gap is that is a "hub" matrix in the sense that it has dominant columns. Some applications of this hub theory in multiple-input and multiple-output (MIMO wireless systems are presented.

  8. The Virtual Campus Hub Concept

    DEFF Research Database (Denmark)

    Badger, Merete; Prag, Sidsel-Marie Winther; Monaco, Lucio

    of Technology in Sweden, Politecnico di Torino in Italy, and Eindhoven University of Technology in the Netherlands. The project is partially funded by the European Commission under the 7th Framework Programme (project no. RI-283746). This report describes the final concept of Virtual Campus Hub. It gives...

  9. Patterns of failure in children with medulloblastoma treated with 3D conformal radiotherapy

    International Nuclear Information System (INIS)

    Skowronska-Gardas, Anna; Chojnacka, Marzanna; Morawska-Kaczynska, Marzena; Perek, Danuta; Perek-Polnik, Marta

    2007-01-01

    Background and purpose: Craniospinal irradiation for medulloblastoma is one of the most complex techniques employed in radiotherapy. Many reports stress the impact of irradiation quality on survival in these patients. Our report presents the outcome and patterns of failure for 95 patients treated with 3D conformal radiotherapy (3D-CRT). Materials and methods: From 1998 to 2003, 95 children with medulloblastoma received 3D conformal radiotherapy. All of them were previously treated with surgery and chemotherapy. The brain and upper spinal cord were treated with two lateral 6 MV photon fields. In four patients, the cribriform plate was irradiated by the additional field. For primary tumour bed we applied two or three photon beams. Spinal cord was irradiated either with 18-20 MeV electron fields or with a mixed beam. Results: With a median follow-up of 48 months, 32/95 patients suffered a multifocal (21) or isolated (11) recurrence. We evaluated every primary site of failure. In all patients, the recurrence appeared within the isodose level of 95-100%. Conclusions: Patterns of failure in medulloblastoma patients treated with 3D conformal radiotherapy indicated that the relapse was mainly associated with poor response to pre-irradiation chemotherapy. We believe that 3D conformal radiotherapy allows avoiding failures, related to radiotherapy uncertainties

  10. MyGeoHub: A Collaborative Geospatial Research and Education Platform

    Science.gov (United States)

    Kalyanam, R.; Zhao, L.; Biehl, L. L.; Song, C. X.; Merwade, V.; Villoria, N.

    2017-12-01

    Scientific research is increasingly collaborative and globally distributed; research groups now rely on web-based scientific tools and data management systems to simplify their day-to-day collaborative workflows. However, such tools often lack seamless interfaces, requiring researchers to contend with manual data transfers, annotation and sharing. MyGeoHub is a web platform that supports out-of-the-box, seamless workflows involving data ingestion, metadata extraction, analysis, sharing and publication. MyGeoHub is built on the HUBzero cyberinfrastructure platform and adds general-purpose software building blocks (GABBs), for geospatial data management, visualization and analysis. A data management building block iData, processes geospatial files, extracting metadata for keyword and map-based search while enabling quick previews. iData is pervasive, allowing access through a web interface, scientific tools on MyGeoHub or even mobile field devices via a data service API. GABBs includes a Python map library as well as map widgets that in a few lines of code, generate complete geospatial visualization web interfaces for scientific tools. GABBs also includes powerful tools that can be used with no programming effort. The GeoBuilder tool provides an intuitive wizard for importing multi-variable, geo-located time series data (typical of sensor readings, GPS trackers) to build visualizations supporting data filtering and plotting. MyGeoHub has been used in tutorials at scientific conferences and educational activities for K-12 students. MyGeoHub is also constantly evolving; the recent addition of Jupyter and R Shiny notebook environments enable reproducible, richly interactive geospatial analyses and applications ranging from simple pre-processing to published tools. MyGeoHub is not a monolithic geospatial science gateway, instead it supports diverse needs ranging from just a feature-rich data management system, to complex scientific tools and workflows.

  11. Soft Power and Cultural Diplomacy: Emerging Education Hubs in Asia

    Science.gov (United States)

    Lee, Jack T.

    2015-01-01

    Several education hubs have emerged in Asia and the Middle East in recent years with a specific focus on cross-border higher education. Through considerable efforts in policy planning and generous funding, these hubs aim to transform a country or city into an eminent destination for education, research, and training. The inherent design of these…

  12. 75 FR 3217 - J&T Hydro Company; H. Dean Brooks and W. Bruce Cox; Notice of Application for Transfer of License...

    Science.gov (United States)

    2010-01-20

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 11392-009] J&T Hydro Company; H. Dean Brooks and W. Bruce Cox; Notice of Application for Transfer of License and Soliciting Comments and Motions To Intervene January 12, 2010. On October 30, 2009, J&T Hydro Company (transferor) and...

  13. Parathyroid hormone and vitamin D--markers for cardiovascular and all cause mortality in heart failure

    DEFF Research Database (Denmark)

    Schierbeck, Louise Lind; Jensen, Torben Slott; Bang, Ulrich

    2011-01-01

    To investigate levels of vitamin D and parathyroid hormone (PTH) in a population of heart failure (HF) patients, and to evaluate whether vitamin D and PTH are related to prognosis.......To investigate levels of vitamin D and parathyroid hormone (PTH) in a population of heart failure (HF) patients, and to evaluate whether vitamin D and PTH are related to prognosis....

  14. Physics and operation oriented activities in preparation of the JT-60SA tokamak exploitation

    Science.gov (United States)

    Giruzzi, G.; Yoshida, M.; Artaud, J. F.; Asztalos, Ö.; Barbato, E.; Bettini, P.; Bierwage, A.; Boboc, A.; Bolzonella, T.; Clement-Lorenzo, S.; Coda, S.; Cruz, N.; Day, Chr.; De Tommasi, G.; Dibon, M.; Douai, D.; Dunai, D.; Enoeda, M.; Farina, D.; Figini, L.; Fukumoto, M.; Galazka, K.; Galdon, J.; Garcia, J.; Garcia-Muñoz, M.; Garzotti, L.; Gil, C.; Gleason-Gonzalez, C.; Goodman, T.; Granucci, G.; Hayashi, N.; Hoshino, K.; Ide, S.; Imazawa, R.; Innocente, P.; Isayama, A.; Itami, K.; Joffrin, E.; Kamada, Y.; Kamiya, K.; Kawano, Y.; Kawashima, H.; Kobayashi, T.; Kojima, A.; Kubo, H.; Lang, P.; Lauber, Ph.; de la Luna, E.; Maget, P.; Marchiori, G.; Mastrostefano, S.; Matsunaga, G.; Mattei, M.; McDonald, D. C.; Mele, A.; Miyata, Y.; Moriyama, S.; Moro, A.; Nakano, T.; Neu, R.; Nowak, S.; Orsitto, F. P.; Pautasso, G.; Pégourié, B.; Pigatto, L.; Pironti, A.; Platania, P.; Pokol, G. I.; Ricci, D.; Romanelli, M.; Saarelma, S.; Sakurai, S.; Sartori, F.; Sasao, H.; Scannapiego, M.; Shimizu, K.; Shinohara, K.; Shiraishi, J.; Soare, S.; Sozzi, C.; Stępniewski, W.; Suzuki, T.; Suzuki, Y.; Szepesi, T.; Takechi, M.; Tanaka, K.; Terranova, D.; Toma, M.; Urano, H.; Vega, J.; Villone, F.; Vitale, V.; Wakatsuki, T.; Wischmeier, M.; Zagórski, R.

    2017-08-01

    The JT-60SA tokamak, being built under the Broader Approach agreement jointly by Europe and Japan, is due to start operation in 2020 and is expected to give substantial contributions to both ITER and DEMO scenario optimisation. A broad set of preparation activities for an efficient start of the experiments on JT-60SA is being carried out, involving elaboration of the Research Plan, advanced modelling in various domains, feasibility and conception studies of diagnostics and other sub-systems in connection with the priorities of the scientific programme, development and validation of operation tools. The logic and coherence of this approach, as well as the most significant results of the main activities undertaken are presented and summarised.

  15. JT-60 plasma control system

    International Nuclear Information System (INIS)

    Kurihara, K.

    1988-01-01

    JT-60 plasma control can be performed by the supervisory controller, the measurement system and actuators such as the poloidal field coil power supplies, gas injectors, neutral beam injection (NBI) heating system and radio frequency (RF) heating system. One of the most important characteristics of this system is a perfect digital control one composed of mini-computers, fast array processors and CAMAC modules, and it has large flexibility and few troubles to adjust the system. This system started to be operated in April 1985, after the six-year-long design, construction and testing, and have been operated and improved many times for two years. In this paper, the final system specification and its performance are presented aiming at the technological aspect of hardware and software. In addition, and experienced troubles are also presented. (author)

  16. Analysis of Sci-Hub downloads of computer science papers

    Directory of Open Access Journals (Sweden)

    Andročec Darko

    2017-07-01

    Full Text Available The scientific knowledge is disseminated by research papers. Most of the research literature is copyrighted by publishers and avail- able only through paywalls. Recently, some websites offer most of the recent content for free. One of them is the controversial website Sci-Hub that enables access to more than 47 million pirated research papers. In April 2016, Science Magazine published an article on Sci-Hub activity over the period of six months and publicly released the Sci-Hub’s server log data. The mentioned paper aggregates the view that relies on all downloads and for all fields of study, but these findings might be hiding interesting patterns within computer science. The mentioned Sci-Hub log data was used in this paper to analyse downloads of computer science papers based on DBLP’s list of computer science publications. The top downloads of computer science papers were analysed, together with the geographical location of Sci-Hub users, the most downloaded publishers, types of papers downloaded, and downloads of computer science papers per publication year. The results of this research can be used to improve legal access to the most relevant scientific repositories or journals for the computer science field.

  17. Conceptual design of divertor cassette handling by remote handling system for JT-60SA

    International Nuclear Information System (INIS)

    Hayashi, Takao; Sakurai, Shinji; Masaki, Kei; Tamai, Hiroshi; Yoshida, Kiyoshi; Matsukawa, Makoto

    2007-01-01

    The JT-60SA aims to contribute and supplement ITER toward DEMO reactor based on tokamak concept. One of the features of JT-60SA is its high power long pulse heating, causing the large annual neutron fluence. Because the expected dose rate at the vacuum vessel (VV) may exceed 1 mSv/hr after 10 years operation and three month cooling, the human access inside the VV is prohibited. Therefore a remote handling (RH) system is necessary for the maintenance and repair of in-vessel components. This paper described the RH system of JT-60SA, especially the expansion of the RH rail and exchange of the divertor modules. The RH rail is divided into nine and three-point mounting. The nine sections can cover 225 degrees in toroidal direction. A divertor module, which is 10 degrees wide in toroidal direction and weighs 500kg itself due to the limitations of port width and handling weight, can be exchanged by heavy weight manipulator (HWM). The HWM brings the divertor module to the front of the other RH port, which is used for supporting the rail and/or carrying in and out equipments. Then another RH device receives and brings out the module by a pallet installed from outside the VV. (author)

  18. Conceptual design of divertor cassette handling by remote handling system of JT-60SA

    International Nuclear Information System (INIS)

    Hayashi, Takao; Sakurai, Shinji; Masaki, Kei; Tamai, Hiroshi; Yoshida, Kiyoshi; Matsukawa, Makoto

    2008-01-01

    The JT-60SA aims to contribute and supplement ITER toward demonstration fusion reactor based on tokamak concept. One of the features of JT-60SA is its high power long pulse heating, causing the large annual neutron fluence. Because the expected dose rate at the vacuum vessel (VV) may exceed 1 mSv/hr after 10 years operation and three month cooling, the human access inside the VV is restricted. Therefore a remote handling (RH) system is necessary for the maintenance and repair of in-vessel components. This paper described the RH system of JT-60SA, especially the expansion of the RH rail and exchange of the divertor cassettes. The RH rail is divided into nine and three-point mounting. The nine sections can cover 225 degrees in toroidal direction. A divertor cassette, which is 10 degrees wide in toroidal direction and weighs 500 kg itself due to the limitations of port width and handling weight, can be exchanged by heavy weight manipulator (HWM). The HWM brings the divertor cassette to the front of the other RH port, which is used for supporting the rail and/or carrying in and out equipments. Then another RH device receives and brings out the cassette by a pallet installed from outside the VV. (author)

  19. Using hybrid latent class model for city-HUBs´users behaviour analysis

    OpenAIRE

    Di Ciommo, Floridea; Monzón de Cáceres, Andrés; Oña, Rocío de; Oña López, Juan de; Hernández del Olmo, Sara

    2014-01-01

    Data from an attitudinal survey and stated preference ranking experiment conducted in two urban European interchanges (i.e. City-HUBs) in Madrid (Spain) and Thessaloniki (Greece) show that the importance that City-HUBs users attach to the intermodal infrastructure varies strongly as a function of their perceptions of time spent in the interchange (i.e.intermodal transfer and waiting time). A principal components analysis allocates respondents (i.e. city-HUB users) to two classes with substant...

  20. Design study of a new P-NBI control system for 100-s injection in JT-60SA

    International Nuclear Information System (INIS)

    Honda, Atsushi; Okano, Fuminori; Shinozaki, Shinichi; Ooshima, Katsumi; Ikeda, Yoshitaka; Numazawa, Susumu

    2007-03-01

    The modification of the JT-60U to a fully superconducting coil tokamak, JT-60SA (Super Advanced), has been programmed as the satellite devise for the ITER (International Thermonuclear Experimental Reactor) and as the national centralized tokamak. The present positive-ion-based NBI system (P-NBI), which has been operated for 20 years and will be the main heating system on JT-60SA, is required to manage the long pulse injection extended from 30 s to 100 s at the power of 24 MW with 12 units. To realize such a requirement, the original control system handling more than 4000 digital data is to be fully remodeled. Design study of the new control system has been conducted from viewpoint of market availability, system extensibility, cost-effectiveness and independent development in programming. It has been concluded that a distributed control system using PLC (Programmable Logic Controller) could be applied to the large-scale control system for 100-s operations with satisfaction of the evaluation viewpoints. (author)

  1. The BioHub Knowledge Base: Ontology and Repository for Sustainable Biosourcing.

    Science.gov (United States)

    Read, Warren J; Demetriou, George; Nenadic, Goran; Ruddock, Noel; Stevens, Robert; Winter, Jerry

    2016-06-01

    The motivation for the BioHub project is to create an Integrated Knowledge Management System (IKMS) that will enable chemists to source ingredients from bio-renewables, rather than from non-sustainable sources such as fossil oil and its derivatives. The BioHubKB is the data repository of the IKMS; it employs Semantic Web technologies, especially OWL, to host data about chemical transformations, bio-renewable feedstocks, co-product streams and their chemical components. Access to this knowledge base is provided to other modules within the IKMS through a set of RESTful web services, driven by SPARQL queries to a Sesame back-end. The BioHubKB re-uses several bio-ontologies and bespoke extensions, primarily for chemical feedstocks and products, to form its knowledge organisation schema. Parts of plants form feedstocks, while various processes generate co-product streams that contain certain chemicals. Both chemicals and transformations are associated with certain qualities, which the BioHubKB also attempts to capture. Of immediate commercial and industrial importance is to estimate the cost of particular sets of chemical transformations (leading to candidate surfactants) performed in sequence, and these costs too are captured. Data are sourced from companies' internal knowledge and document stores, and from the publicly available literature. Both text analytics and manual curation play their part in populating the ontology. We describe the prototype IKMS, the BioHubKB and the services that it supports for the IKMS. The BioHubKB can be found via http://biohub.cs.manchester.ac.uk/ontology/biohub-kb.owl .

  2. Features analysis for identification of date and party hubs in protein interaction network of Saccharomyces Cerevisiae

    Directory of Open Access Journals (Sweden)

    Araabi Babak N

    2010-12-01

    Full Text Available Abstract Background It has been understood that biological networks have modular organizations which are the sources of their observed complexity. Analysis of networks and motifs has shown that two types of hubs, party hubs and date hubs, are responsible for this complexity. Party hubs are local coordinators because of their high co-expressions with their partners, whereas date hubs display low co-expressions and are assumed as global connectors. However there is no mutual agreement on these concepts in related literature with different studies reporting their results on different data sets. We investigated whether there is a relation between the biological features of Saccharomyces Cerevisiae's proteins and their roles as non-hubs, intermediately connected, party hubs, and date hubs. We propose a classifier that separates these four classes. Results We extracted different biological characteristics including amino acid sequences, domain contents, repeated domains, functional categories, biological processes, cellular compartments, disordered regions, and position specific scoring matrix from various sources. Several classifiers are examined and the best feature-sets based on average correct classification rate and correlation coefficients of the results are selected. We show that fusion of five feature-sets including domains, Position Specific Scoring Matrix-400, cellular compartments level one, and composition pairs with two and one gaps provide the best discrimination with an average correct classification rate of 77%. Conclusions We study a variety of known biological feature-sets of the proteins and show that there is a relation between domains, Position Specific Scoring Matrix-400, cellular compartments level one, composition pairs with two and one gaps of Saccharomyces Cerevisiae's proteins, and their roles in the protein interaction network as non-hubs, intermediately connected, party hubs and date hubs. This study also confirms the

  3. Quench detection of fast plasma events for the JT-60SA central solenoid

    International Nuclear Information System (INIS)

    Murakami, Haruyuki; Kizu, Kaname; Tsuchiya, Katsuhiko; Kamiya, Koji; Takahashi, Yoshikazu; Yoshida, Kiyoshi

    2012-01-01

    Highlights: ► Pick-up coil method is used for the quench detection of JT-60SA magnet system. ► Disk-shaped pick-up coils are inserted in CS module to compensate inductive voltage. ► Applicability of pick-up coil is evaluated by two dimensional analysis. ► Pick-up coil is applicable whenever disruption, mini collapse and other plasma event. - Abstract: The JT-60 is planned to be modified to a full-superconducting tokamak referred to as the JT-60 Super Advanced (JT-60SA). The maximum temperature of the magnet during its quench might reach the temperature of higher than several hundreds Kelvin that will damage the superconducting magnet itself. The high precision quench detection system, therefore, is one of the key technologies in the superconducting magnet protection system. The pick-up coil method, which is using voltage taps to detect the normal voltage, is used for the quench detection of the JT-60SA superconducting magnet system. The disk-shaped pick-up coils are inserted in the central solenoid (CS) module to compensate the inductive voltage. In the previous study, the quench detection system requires a large number of pick-up coils. The reliability of quench detection system would be higher by simplifying the detection system such as reducing the number of pick-up coils. Simplifying the quench detection system is also important to reduce the total cost of the protection system. Hence the design method is improved by increasing optimizing parameters. The improved design method can reduce the number of pick-up coils without reducing the sensitivity of detection; consequently the protection system can be designed with higher reliability and lower cost. The applicability of the disk-shaped pick-up coil for quench detection system is evaluated by the two dimensional analysis. In the previous study, however, the analysis model only took into account the CS, EF (equilibrium field) coils and plasma. Therefore, applicability of the disk-shaped pick-up coil for

  4. ASDEX Upgrade-JT-60U comparison and ECRH power requirements for NTM stabilization in ITER

    International Nuclear Information System (INIS)

    Urso, L.; Zohm, H.; Maraschek, M.; Poli, E.; Isayama, A.

    2010-01-01

    Neoclassical tearing modes (NTMs) are experimentally controlled with local electron cyclotron current drive (ECCD) and the island width decay during NTM stabilization is modelled using the so-called modified Rutherford equation (MRE). In this paper, a modelling of the MRE is carried out and simulations of the island width decay are compared with the experimentally observed ones in order to fit the two free machine-independent parameters present in the equation. A systematic study on a database of NTM stabilization discharges from ASDEX Upgrade and JT-60U is done for extrapolating the ECCD power requirements for ITER. The extrapolation to ITER of the NTM stabilization results from ASDEX Upgrade and JT-60U shows that 10 MW of ECCD power are enough to stabilize large NTMs. The 10 MW power estimate for ITER is based on the assumption that the free parameters in the MRE are machine independent. Indeed, this assumption is verified in this paper for ASDEX Upgrade and JT-60U. An interesting consequence of the relatively modest power requirement for ITER is that the installed 20 MW will suffice for simultaneous 2/1 and 3/2 NTM stabilization.

  5. Functional Hubs in Mild Cognitive Impairment

    Science.gov (United States)

    Navas, Adrián; Papo, David; Boccaletti, Stefano; Del-Pozo, F.; Bajo, Ricardo; Maestú, Fernando; Martínez, J. H.; Gil, Pablo; Sendiña-Nadal, Irene; Buldú, Javier M.

    We investigate how hubs of functional brain networks are modified as a result of mild cognitive impairment (MCI), a condition causing a slight but noticeable decline in cognitive abilities, which sometimes precedes the onset of Alzheimer's disease. We used magnetoencephalography (MEG) to investigate the functional brain networks of a group of patients suffering from MCI and a control group of healthy subjects, during the execution of a short-term memory task. Couplings between brain sites were evaluated using synchronization likelihood, from which a network of functional interdependencies was constructed and the centrality, i.e. importance, of their nodes was quantified. The results showed that, with respect to healthy controls, MCI patients were associated with decreases and increases in hub centrality respectively in occipital and central scalp regions, supporting the hypothesis that MCI modifies functional brain network topology, leading to more random structures.

  6. MODELS AND METHODS FOR LOGISTICS HUB LOCATION: A REVIEW TOWARDS TRANSPORTATION NETWORKS DESIGN

    Directory of Open Access Journals (Sweden)

    Carolina Luisa dos Santos Vieira

    Full Text Available ABSTRACT Logistics hubs affect the distribution patterns in transportation networks since they are flow-concentrating structures. Indeed, the efficient moving of goods throughout supply chains depends on the design of such networks. This paper presents a literature review on the logistics hub location problem, providing an outline of modeling approaches, solving techniques, and their applicability to such context. Two categories of models were identified. While multi-criteria models may seem best suited to find optimal locations, they do not allow an assessment of the impact of new hubs on goods flow and on the transportation network. On the other hand, single-criterion models, which provide location and flow allocation information, adopt network simplifications that hinder an accurate representation of the relationshipbetween origins, destinations, and hubs. In view of these limitations we propose future research directions for addressing real challenges of logistics hubs location regarding transportation networks design.

  7. Global energy confinement in JT-60 neutral beam heated L-mode discharges

    International Nuclear Information System (INIS)

    Naito, O.; Hosogane, N.; Tsuji, S.; Ushigusa, K.; Yoshida, H.

    1990-01-01

    The global energy confinement characteristics of neutral beam heated JT-60 discharges are presented. There is a difference in the dependence of the energy confinement time on the plasma current between limiter and divertor discharges. For limiter discharges, the energy confinement increases with plasma current up to 3.2 MA, whereas for divertor discharges this improvement saturates when the safety factor drops below 3, independent of the location of the X-point. The JT-60 L-mode results indicate that the deterioration in energy confinement for q < 3, which is also found in H-mode regimes of other devices, may be a universal characteristic of divertor discharges. Regarding the scaling with plasma size, it is shown that the global/incremental confinement time increases with plasma minor radius. For sufficiently large plasmas, however, the global/incremental confinement time is no longer a function of minor radius. (author). 13 refs, 14 figs

  8. Epidemics in Complex Networks: The Diversity of Hubs

    Science.gov (United States)

    Kitsak, Maksim; Gallos, Lazaros K.; Havlin, Shlomo; Stanley, H. Eugene; Makse, Hernan A.

    2009-03-01

    Many complex systems are believed to be vulnerable to spread of viruses and information owing to their high level of interconnectivity. Even viruses of low contagiousness easily proliferate the Internet. Rumors, fads, and innovation ideas are prone to efficient spreading in various social systems. Another commonly accepted standpoint is the importance of the most connected elements (hubs) in the spreading processes. We address following questions. Do all hubs conduct epidemics in the same manner? How does the epidemics spread depend on the structure of the network? What is the most efficient way to spread information over the system? We analyze several large-scale systems in the framework of of the susceptible/infective/removed (SIR) disease spread model which can also be mapped to the problem of rumor or fad spreading. We show that hubs are often ineffective in the transmission of virus or information owing to the highly heterogeneous topology of most networks. We also propose a new tool to evaluate the efficiency of nodes in spreading virus or information.

  9. Improvement of JT-60U Negative Ion Source Performance

    International Nuclear Information System (INIS)

    Grisham, L.R.; Kuriyama, M.; Kawai, M.; Itoh, T.; Umeda, N.

    2000-01-01

    The negative ion neutral beam system now operating on JT-60U was the first application of negative ion technology to the production of beams of high current and power for conversion to neutral beams, and has successfully demonstrated the feasibility of negative ion beam heating systems for ITER and future tokamak reactors [1, 2]. It also demonstrated significant electron heating[3] and high current drive efficiency in JT-60U[4]. Because this was such a large advance in the state of the art with respect to all system parameters, many new physical processes appeared during the earlier phases of the beam injection experiments. We have explored the physical mechanisms responsible for these processes, and implemented solutions for some of them, in particular excessive beam stripping, the secular dependence of the arc and beam parameters, and nonuniformity of the plasma illuminating the beam extraction grid. This has reduced the percentage of beam heat loading on the downstream grids by roug hly a third, and permitted longer beam pulses at higher powers. Progress is being made in improving the negative ion current density, and in coping with the sensitivity of the cesium in the ion sources to oxidation by tiny air or water leaks, and the cathode operation is being altered

  10. Looking Into Pandora's Box: The Content Of Sci-Hub And Its Usage

    OpenAIRE

    Greshake, Bastian

    2017-01-01

    Despite the growth of Open Access, potentially illegally circumventing paywalls to access scholarly publications is becoming a more mainstream phenomenon. The web service Sci-Hub is amongst the biggest facilitators of this, offering free access to around 62 million publications. So far it is not well studied how and why its users are accessing publications through Sci-Hub. By utilizing the recently released corpus of Sci-Hub and comparing it to the data of  ~28 million downloads done through ...

  11. Influence of Hub Parameters on Joining Forces and Torque Transmission Output of Plastically-Joined Shaft-Hub-Connections with a Knurled Contact Surface

    Directory of Open Access Journals (Sweden)

    Lukáš Suchý

    2018-04-01

    Full Text Available A knurled interference fit is a machine part connection made by a plastic joining, which includes the advantages of commonly-used shaft-hub-connections. The combination of the friction and form fit, which are responsible for torque transmission, results in a higher power density than conventional connections. In this paper, parameter gaps are bridged with the aim of enhance the design calculation of the knurled interference fit. Experimental investigations on the shaft chamfer angle (100Cr6 and hub-diameter-ratio (AlSi1MgMn were performed. The analytical approaches are developed for calculating the joining force and maximal torque capacity by accounting for experimentally investigated loss of load transmission at high hub-diameter-ratios and high shaft chamfer angles. The presented calculation approach is an accurate tool for the assessment of early machine designs of the knurled interference fit and helps to save from having to perform time-extensive tests.

  12. Advancing nanoelectronic device modeling through peta-scale computing and deployment on nanoHUB

    International Nuclear Information System (INIS)

    Haley, Benjamin P; Luisier, Mathieu; Klimeck, Gerhard; Lee, Sunhee; Ryu, Hoon; Bae, Hansang; Saied, Faisal; Clark, Steve

    2009-01-01

    Recent improvements to existing HPC codes NEMO 3-D and OMEN, combined with access to peta-scale computing resources, have enabled realistic device engineering simulations that were previously infeasible. NEMO 3-D can now simulate 1 billion atom systems, and, using 3D spatial decomposition, scale to 32768 cores. Simulation time for the band structure of an experimental P doped Si quantum computing device fell from 40 minutes to 1 minute. OMEN can perform fully quantum mechanical transport calculations for real-word UTB FETs on 147,456 cores in roughly 5 minutes. Both of these tools power simulation engines on the nanoHUB, giving the community access to previously unavailable research capabilities.

  13. Success as Failure and Failure as Success: The Cultural Literacy of E. D. Hirsch, Jr.

    Science.gov (United States)

    Sledd, Andrew E.; Sledd, James H.

    1989-01-01

    Examines the logic and rhetoric of E. D. Hirsch, Jr., in "Cultural Literacy." Attempts to answer the question of how intellectual failure guarantees success in the marketplace. Concludes with an alternative vision of the American society that Hirsch describes and the suggestion that Hirsch's cultural literacy is cross-cultural…

  14. Failure Diameter Resolution Study

    Energy Technology Data Exchange (ETDEWEB)

    Menikoff, Ralph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-12-19

    Previously the SURFplus reactive burn model was calibrated for the TATB based explosive PBX 9502. The calibration was based on fitting Pop plot data, the failure diameter and the limiting detonation speed, and curvature effect data for small curvature. The model failure diameter is determined utilizing 2-D simulations of an unconfined rate stick to find the minimum diameter for which a detonation wave propagates. Here we examine the effect of mesh resolution on an unconfined rate stick with a diameter (10mm) slightly greater than the measured failure diameter (8 to 9 mm).

  15. Economic Impact of the Dutch Gas Hub Strategy on the Netherlands

    International Nuclear Information System (INIS)

    Harris, D.; Bazelon, C.; Humphreys, B.; Dickson, P.

    2010-09-01

    Since the discovery of the Groningen gas field in 1959, the Netherlands has been a key player in the European gas market. The Netherlands has built up a large onshore and offshore Exploration and Production sector, it has a highly developed gas transmission and distribution network, and is a major exporter of gas to other EU Member States. The Netherlands has considerable expertise in all parts of the gas supply chain, and is a world centre for Research and development in natural gas supply and use. More recently construction has begun on terminals to allow the import of Liquid Natural Gas to the Netherlands. However, Dutch gas reserves are now in decline, and the Netherlands will become a net importer of gas around 2025. The Dutch government wishes to capitalise on the existing industry and skills and sustain the Netherlands' place in the European gas industry beyond the life of the existing gas fields. In November 2009 the Minister of Economic Affairs published a paper describing the strategy of turning the Netherlands into a 'Gas Hub' or 'gas roundabout' for north-west Europe. The Dutch government intends that the gas hub would capitalise on the existing skills and industry, increase competition and security of supply in the Dutch gas market, create employment and make a significant contribution to the Dutch economy. The Dutch Ministry of Economic Affairs, Agriculture and Innovation has commissioned The Brattle Group to perform an analysis of the economic impact of the gas hub concept. The study has several aims including: To analyse the current contribution of the Dutch gas sector to the economy; To assess the Strengths, Weaknesses, Opportunities and Threats associated with the gas hub strategy; To quantify the benefits of the gas hub strategy to the Dutch economy. Note that the aim of the study is to define in more detail what a successful Dutch gas hub strategy would look like, to assess the strengths and weakness of the Dutch gas sector in achieving a

  16. The Banana Genome Hub

    Science.gov (United States)

    Droc, Gaëtan; Larivière, Delphine; Guignon, Valentin; Yahiaoui, Nabila; This, Dominique; Garsmeur, Olivier; Dereeper, Alexis; Hamelin, Chantal; Argout, Xavier; Dufayard, Jean-François; Lengelle, Juliette; Baurens, Franc-Christophe; Cenci, Alberto; Pitollat, Bertrand; D’Hont, Angélique; Ruiz, Manuel; Rouard, Mathieu; Bocs, Stéphanie

    2013-01-01

    Banana is one of the world’s favorite fruits and one of the most important crops for developing countries. The banana reference genome sequence (Musa acuminata) was recently released. Given the taxonomic position of Musa, the completed genomic sequence has particular comparative value to provide fresh insights about the evolution of the monocotyledons. The study of the banana genome has been enhanced by a number of tools and resources that allows harnessing its sequence. First, we set up essential tools such as a Community Annotation System, phylogenomics resources and metabolic pathways. Then, to support post-genomic efforts, we improved banana existing systems (e.g. web front end, query builder), we integrated available Musa data into generic systems (e.g. markers and genetic maps, synteny blocks), we have made interoperable with the banana hub, other existing systems containing Musa data (e.g. transcriptomics, rice reference genome, workflow manager) and finally, we generated new results from sequence analyses (e.g. SNP and polymorphism analysis). Several uses cases illustrate how the Banana Genome Hub can be used to study gene families. Overall, with this collaborative effort, we discuss the importance of the interoperability toward data integration between existing information systems. Database URL: http://banana-genome.cirad.fr/ PMID:23707967

  17. Location of an intermediate hub for port activities

    Science.gov (United States)

    Burciu, Ş.; Ştefănică, C.; Roşca, E.; Dragu, V.; Ruscă, F.

    2015-11-01

    An intermediate hub might increase the accessibility level of ports but also hinterland and so it can be considered more than a facility with a transhipment role. These hubs might lead to the development of other transport services and enhance their role in gathering and covering economic centres within hinterlands and also getting the part of logistic facility for the ports, with effects on port utilization and its connectivity to global economy. A new location for a hub terminal leads to reduced transport distances within hinterland, with decreased transport costs and external effects, so with gains in people's life quality. Because the production and distribution systems are relatively fixed on short and medium term and the location decisions are strategic and on long term, the logistic chains activities location models have to consider the uncertainties regarding the possible future situations. In most models, production costs are considered equal, the location problem reducing itself to a problem that aims to minimize the total transport costs, meaning the transport problem. The main objective of the paper is to locate a hub terminal that links the producers of cereals that are going to be exported by naval transportation with the Romanian fluvial-maritime ports (Galaţi, Brăila). GIS environment can be used to integrate and analyse a great amount of data and has the ability of using functions as location - allocation models necessary both to private and public sector, being able to determine the optimal location for services like factories, warehouses, logistic platforms and other public services.

  18. Maritime Domain Awareness Architecture Management Hub Strategy

    National Research Council Canada - National Science Library

    2008-01-01

    This document provides an initial high level strategy for carrying out the responsibilities of the national Maritime Domain Awareness Architecture Management Hub to deliver a standards based service...

  19. VME multiprocessor system for plasma control at the JT-60 Upgrade

    International Nuclear Information System (INIS)

    Kimura, T.; Kurihara, K.; Takahashi, M.; Kawamata, Y.; Akasaka, H.; Matsukawa, M.

    1989-01-01

    In this paper design and preliminary tests are reported of a VME multiprocessor system for the JT-60 Upgrade plasma control utilizing three MC88100 based RISC computers and VME buses. The design of the VME system was stimulated by faster and more accurate computation requirements for the plasma position and shape control

  20. The healthiness of JT-60 ICRF antenna and development of its temperature measurement device

    International Nuclear Information System (INIS)

    Hiranai, Shinichi; Yokokura, Kenji; Moriyama, Shinichi; Sato, Tomio; Ishii, Kazuhiro; Fujii, Tsuneyuki

    1998-03-01

    Ion Cyclotron Range of Frequency (ICRF) heating system in JT-60 employs two antennas to couple RF power in the range of 100 MHz to the plasma. The antennas are installed in the vacuum vessel of JT-60, facing to the high temperature plasma. Due to the severe heat load from the plasma, parts of the antenna surface are suffering from melt. It is important to investigate the mechanism of the heat load and the melting. 'Temperature measurement for ICRF antenna surface' employing an infrared thermographic camera has been developed, in order to investigate the heat load to the antenna and to maintain the antenna available. We have succeeded in minimizing the melting damage of the antenna surface using the temperature measurement device. (author)

  1. With 8D method to excellent quality

    Directory of Open Access Journals (Sweden)

    Marjanca Krajnc

    2012-10-01

    Full Text Available RQ: The research aims to establish the suitability of the 8D methodology for complaint settlement, and to identify any resulting improvement in quality.Purpose: Studies that have research the 8D method are scarce in international literature. Consequently, we decided to assess, based on theoretical premises, the suitability of the 8D method used by an organization, and the efficiency of quality performance directly associated with the 8D method. We will establish whether the use ofthe 8D method results in quality improvement.Method: The research will be carried out using qualitative analysis in the form of a case study of the 8D method used in an organization. I will discuss, based on real and relevant data, the approaches implemented by individual 8D method steps, indicating the integrated supplemental tools. In the quantitative part, I will identify the defective product trends (PPM and the trends of costs related to defective products.Results: The 8D method used for complaint settlement contributes to improved quality and company performance.Organization: The results can be used by the management in continuous improvement as additional motivation for more consistent and effective use, and for additional support to problem-solving coordinators and teams.Society: The findings can also be applied by society at large, mostly companies and public services.Originality: Research on this topic or combination has not yet been conductedLimitations: The sample studied is small, limited to one large company. It includes only the data obtained through the use of the 8D method.

  2. HIV protein sequence hotspots for crosstalk with host hub proteins.

    Directory of Open Access Journals (Sweden)

    Mahdi Sarmady

    Full Text Available HIV proteins target host hub proteins for transient binding interactions. The presence of viral proteins in the infected cell results in out-competition of host proteins in their interaction with hub proteins, drastically affecting cell physiology. Functional genomics and interactome datasets can be used to quantify the sequence hotspots on the HIV proteome mediating interactions with host hub proteins. In this study, we used the HIV and human interactome databases to identify HIV targeted host hub proteins and their host binding partners (H2. We developed a high throughput computational procedure utilizing motif discovery algorithms on sets of protein sequences, including sequences of HIV and H2 proteins. We identified as HIV sequence hotspots those linear motifs that are highly conserved on HIV sequences and at the same time have a statistically enriched presence on the sequences of H2 proteins. The HIV protein motifs discovered in this study are expressed by subsets of H2 host proteins potentially outcompeted by HIV proteins. A large subset of these motifs is involved in cleavage, nuclear localization, phosphorylation, and transcription factor binding events. Many such motifs are clustered on an HIV sequence in the form of hotspots. The sequential positions of these hotspots are consistent with the curated literature on phenotype altering residue mutations, as well as with existing binding site data. The hotspot map produced in this study is the first global portrayal of HIV motifs involved in altering the host protein network at highly connected hub nodes.

  3. Energy flow modeling and optimal operation analysis of the micro energy grid based on energy hub

    International Nuclear Information System (INIS)

    Ma, Tengfei; Wu, Junyong; Hao, Liangliang

    2017-01-01

    Highlights: • Design a novel architecture for energy hub integrating power hub, cooling hub and heating hub. • The micro energy grid based on energy hub is introduced and its advantages are discussed. • Propose a generic modeling method for the energy flow of micro energy grid. • Propose an optimal operation model for micro energy grid with considering demand response. • The roles of renewable energy, energy storage devices and demand response are discussed separately. - Abstract: The energy security and environmental problems impel people to explore a more efficient, environment friendly and economical energy utilization pattern. In this paper, the coordinated operation and optimal dispatch strategies for multiple energy system are studied at the whole Micro Energy Grid level. To augment the operation flexibility of energy hub, the innovation sub-energy hub structure including power hub, heating hub and cooling hub is put forward. Basing on it, a generic energy hub architecture integrating renewable energy, combined cooling heating and power, and energy storage devices is developed. Moreover, a generic modeling method for the energy flow of micro energy grid is proposed. To minimize the daily operation cost, a day-ahead dynamic optimal operation model is formulated as a mixed integer linear programming optimization problem with considering the demand response. Case studies are undertaken on a community Micro Energy Grid in four different scenarios on a typical summer day and the roles of renewable energy, energy storage devices and demand response are discussed separately. Numerical simulation results indicate that the proposed energy flow modeling and optimal operation method are universal and effective over the entire energy dispatching horizon.

  4. Report on survey on international Hub

    International Nuclear Information System (INIS)

    Ebisawa, Hirobumi; Hoshino, Junko; Hashimoto, Kazuichiro; Okada, Sohei

    2011-03-01

    Japan Atomic Energy Agency (JAEA) is promoting initiative to form an international Center of Excellence in line with its aim to accept more researchers/engineers from all over the world. Establishment of 'the Committee for JAEA Internationalization Initiative' was planned in 2010 so as to intensify this initiative, and in February, 2010, we visited research institutions in Europe, which include European Organization for Nuclear Research (CERN), the construction site of ITER in Cadarache, and Rutherford Appleton Laboratory (RAL), with the intention to survey and learn their advanced activities and systems in regard to the International Hub, so that the committee will be able to make fruitful discussion. This report describes strategy taken in each institution for an International Hub, and the state of each institution regarding acceptance and management of overseas researchers and engineers, research environment, living environment/health and welfare, and PR activities/coexistence with the local community. (author)

  5. Plasma regimes and research goals of JT-60SA towards ITER and DEMO

    International Nuclear Information System (INIS)

    Kamada, Y.; Ide, S.; Fujita, T.; Suzuki, T.; Matsunaga, G.; Yoshida, M.; Shinohara, K.; Urano, H.; Nakano, T.; Sakurai, S.; Kawashima, H.; Barabaschi, P.; Lackner, K.; Ishida, S.; Bolzonella, T.

    2011-01-01

    The JT-60SA device has been designed as a highly shaped large superconducting tokamak with a variety of plasma actuators (heating, current drive, momentum input, stability control coils, resonant magnetic perturbation coils, W-shaped divertor, fuelling, pumping, etc) in order to satisfy the central research needs for ITER and DEMO. In the ITER- and DEMO-relevant plasma parameter regimes and with DEMO-equivalent plasma shapes, JT-60SA quantifies the operation limits, plasma responses and operational margins in terms of MHD stability, plasma transport and confinement, high-energy particle behaviour, pedestal structures, scrape-off layer and divertor characteristics. By integrating advanced studies in these research fields, the project proceeds 'simultaneous and steady-state sustainment of the key performances required for DEMO' with integrated control scenario development applicable to the highly self-regulating burning high-β high bootstrap current fraction plasmas.

  6. Design and development of a four-cell sorption compressor based J-T cooler using R134a as working fluid

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, R. N. [Mechanical Engineering Department, Indian Institute of Technology Bombay, Mumbai - 400076, India and Government Engineering College Bharuch, Gujarat - 392002 (India); Bapat, S. L.; Atrey, M. D. [Mechanical Engineering Department, Indian Institute of Technology Bombay, Mumbai - 400076 (India)

    2014-01-29

    The need of a cooler with no electromagnetic interference and practically zero vibration has led to sorption compressor based Joule-Thomson (J-T) coolers. These are useful for sophisticated electronic, ground based and space borne systems. In a Sorption compressor, adsorbed gases are desorbed into a confined volume by raising temperature of the sorption bed resulting in an increase in pressure of the liberated gas. In order to have the system (compressor) functioning on a continuous basis, with almost a constant gas flow rate, multiple cells are used with the adaptation of Temperature Swing Adsorption (TSA) process. As the mass of the desorbed gas dictates the compressor throughput, a combination of sorbent material with high adsorption capacity for a chosen gas or gas mixture has to be selected for efficient operation of the compressor. Commercially available (coconut-shell base) activated carbon has been selected for the present application. The characterization study for variation of discharge pressure is used to design the Four-cell sorption compressor based cryocooler with a desired output. Apart from compressor, the system includes a) After cooler b) Return gas heat exchanger c) capillary tube as the J-T expansion device and d) Evaporator.

  7. JT-60 power tests from mechanical and thermal viewpoints of tokamak machine

    International Nuclear Information System (INIS)

    Takatsu, H.; Yamamoto, M.; Ohkubo, M.

    1986-01-01

    JT-60 power tests were carried out, to demonstrate, in advance of actual plasma operation, satisfactory performance of the tokamak machine, power suppliers and control system in combination. The tests began with low power ones of individual coil systems, progressed to full power ones and concluded successfully. The present paper describes the principal results of JT-60 power tests from mechanical and thermal viewpoints of tokamak machine. All of the coil systems were raised up to full power operation in combination and system performance was verified including thermal and mechanical integrity of tokamak machine. Measured strain and displacement showed good agreements with those predicted in the design, which was an evidence that electromagnetic loads were supported adequately as expected in the design. Vibration of the vacuum vessel was found to be large up to 48 m/s/sup 2/ and caused excessive vibration of the lateral port gate-valves. A few limitations to machine operation were also made clear quantatively

  8. Modeling and optimization of a network of energy hubs to improve economic and emission considerations

    International Nuclear Information System (INIS)

    Maroufmashat, Azadeh; Elkamel, Ali; Fowler, Michael; Sattari, Sourena; Roshandel, Ramin; Hajimiragha, Amir; Walker, Sean; Entchev, Evgueniy

    2015-01-01

    Energy hubs that incorporate a variety of energy generation and energy transformation technologies can be used to provide the energy storage needed to enable the efficient operation of a ‘smart energy network’. When these hubs are combined as a network and allowed to exchange energy, they create efficiency advantages in both financial and environmental performance. Further, the interconnectedness of the energy network design provides an added layer of reliability. In this paper, a complex network of energy hubs is modeled and optimized under different scenarios to examine both the financial viability and potential reduction of greenhouse gas emissions. Two case studies consisting of two and three energy hubs within a network are considered. The modeling Scenarios vary according to the consideration of distributed energy systems and energy interaction between energy hubs. In the case of a network of two energy hubs, there is no significant economic or emissions benefit with only a 0.5% reduction in total cost and 3% reduction in CO_2 emission. In the case of a network of three energy hubs, there is a significant economic benefit ranging from 11% to 29%, and 11% emission reduction benefit, as well as a 13% reduction in natural gas consumption. - Highlights: • The generic form of the modified energy hub concept with network model is presented. • Two case studies are presented to demonstrate the benefits of energy hub network. • Distributed energy is shown to provide economic and environmental advantages. • Multi criteria optimization of the economic and environmental performance is done.

  9. Disrupted Nodal and Hub Organization Account for Brain Network Abnormalities in Parkinson's Disease.

    Science.gov (United States)

    Koshimori, Yuko; Cho, Sang-Soo; Criaud, Marion; Christopher, Leigh; Jacobs, Mark; Ghadery, Christine; Coakeley, Sarah; Harris, Madeleine; Mizrahi, Romina; Hamani, Clement; Lang, Anthony E; Houle, Sylvain; Strafella, Antonio P

    2016-01-01

    The recent application of graph theory to brain networks promises to shed light on complex diseases such as Parkinson's disease (PD). This study aimed to investigate functional changes in sensorimotor and cognitive networks in Parkinsonian patients, with a focus on inter- and intra-connectivity organization in the disease-associated nodal and hub regions using the graph theoretical analyses. Resting-state functional MRI data of a total of 65 participants, including 23 healthy controls (HCs) and 42 patients, were investigated in 120 nodes for local efficiency, betweenness centrality, and degree. Hub regions were identified in the HC and patient groups. We found nodal and hub changes in patients compared with HCs, including the right pre-supplementary motor area (SMA), left anterior insula, bilateral mid-insula, bilateral dorsolateral prefrontal cortex (DLPFC), and right caudate nucleus. In general, nodal regions within the sensorimotor network (i.e., right pre-SMA and right mid-insula) displayed weakened connectivity, with the former node associated with more severe bradykinesia, and impaired integration with default mode network regions. The left mid-insula also lost its hub properties in patients. Within the executive networks, the left anterior insular cortex lost its hub properties in patients, while a new hub region was identified in the right caudate nucleus, paralleled by an increased level of inter- and intra-connectivity in the bilateral DLPFC possibly representing compensatory mechanisms. These findings highlight the diffuse changes in nodal organization and regional hub disruption accounting for the distributed abnormalities across brain networks and the clinical manifestations of PD.

  10. A collaborative scheduling model for the supply-hub with multiple suppliers and multiple manufacturers.

    Science.gov (United States)

    Li, Guo; Lv, Fei; Guan, Xu

    2014-01-01

    This paper investigates a collaborative scheduling model in the assembly system, wherein multiple suppliers have to deliver their components to the multiple manufacturers under the operation of Supply-Hub. We first develop two different scenarios to examine the impact of Supply-Hub. One is that suppliers and manufacturers make their decisions separately, and the other is that the Supply-Hub makes joint decisions with collaborative scheduling. The results show that our scheduling model with the Supply-Hub is a NP-complete problem, therefore, we propose an auto-adapted differential evolution algorithm to solve this problem. Moreover, we illustrate that the performance of collaborative scheduling by the Supply-Hub is superior to separate decision made by each manufacturer and supplier. Furthermore, we also show that the algorithm proposed has good convergence and reliability, which can be applicable to more complicated supply chain environment.

  11. Communication systems in JT-60 control

    International Nuclear Information System (INIS)

    Kimura, T.; Hosogane, N.; Kondo, I.; Kumahara, T.; Kurihara, K.; Yonekawa, I.; Yoshino, R.

    1983-01-01

    A new concept in communication is applied to the JT-60 control system which handles a large amount of data for the plant support and monitoring and for the discharge control including plasma feedback control. The communication systems are characterized by 1) adoption of an efficient protocol in the central highways which are composed of dual serial CAMAC ones, 2) standardization of the protocol and data format between the central controller and each subsystem one, 3) adoption of a polling method for plant monitoring and of block transfer for discharge conditions and results, and 4) use of novel modules for the fast data transfer in the real-time systems. A compact tool has also been developed for testing the data communication

  12. Doktoritööd : [2007, Anne Lange jt.

    Index Scriptorium Estoniae

    2007-01-01

    20. veebr. kaitseb Anne Lange doktoritööd "The poetics of translation of Ants Oras". 19. jaan. kaitses Tuuli Oder doktoritööd "The model of contemporary professional foreign language teacher". 16. jaan. kaitses Tiit Maran doktoritööd "Conservation biology of the European mink, Mustela lutreola (Linnaeus 1761): decline and causes of extinction". 12. jaan. kaitses Maris Saagpakk doktoritööd "Deutschbaltische Autobiographien als Dokumente des Zeit- und Selbstempfindens: vom Ende des 19. Jh. bis zur Umsiedlung 1939"

  13. Fatigue based design and analysis of wheel hub for Student formula car by Simulation Approach

    Science.gov (United States)

    Gowtham, V.; Ranganathan, A. S.; Satish, S.; Alexis, S. John; Siva kumar, S.

    2016-09-01

    In the existing design of Wheel hub used for Student formula cars, the brake discs cannot be removed easily since the disc is mounted in between the knuckle and hub. In case of bend or any other damage to the disc, the replacement of the disc becomes difficult. Further using OEM hub and knuckle that are used for commercial vehicles will result in increase of unsprung mass, which should be avoided in Student formula cars for improving the performance. In this design the above mentioned difficulties have been overcome by redesigning the hub in such a way that the brake disc could be removed easily by just removing the wheel and the caliper and also it will have reduced weight when compared to existing OEM hub. A CAD Model was developed based on the required fatigue life cycles. The forces acting on the hub were calculated and linear static structural analysis was performed on the wheel hub for three different materials using ANSYS Finite Element code V 16.2. The theoretical fatigue strength was compared with the stress obtained from the structural analysis for each material.

  14. Strategies for contracting gas storage and hub services

    International Nuclear Information System (INIS)

    Auld, J.

    1996-01-01

    The many efficiencies that can be gained by the natural gas industry in effectively using storage, were demonstrated. The circumstances under which the natural gas industry uses storage and how Market Centres or Hub Services can be strategically used in offering companies the highest flexibility in a tough marketplace, were explained. For example, in North America, storage played an important role during the winter of 95/96, which will be remembered for its extreme cold. That year provided the first true opportunity to test the natural gas delivery system since deregulation in 1985. The fact that natural gas supplies continued to be delivered throughout the entire winter was attributed to the use of stored gas held in reserves to meet the severe demand. The companies that did well, relied on storage and also on the services offered by Hub Services which increased margins for all players in the natural gas industry. Using storage, companies can ensure that field deliveries of gas are kept constant by having storage facilities absorb the swings in market demand. The companies that learn to use storage effectively can create competitive edges over their competition and provide more value to their customers. The three main categories of hub services were also described. These are parking (interruptible storage), gas loans (stored gas can be offered to customers on a term basis for low daily rates), and title exchange (the transfer of gas between buyer and seller). The strategic use of parking, loaned gas, title exchange, direct connections, and InterHub Services can provide customers even greater benefits than are provided by storage-based services. 6 figs

  15. Matrix logistics indicators assessment of distributed transport hub

    Directory of Open Access Journals (Sweden)

    Igor Arefyev

    2014-06-01

    Full Text Available Background: The paper is devoted to the distributed transport hub substantiation and assessment. The paper  was an example of the technique and form an array of logistical factors as variables that determine this condition. Experience in organizing multimodal transport showed that the "bottleneck" of transport logistics are items of cargo handling ports, terminals, freight stations and warehouses. At the core of the solution of these problems is the problem of estimating the variables determine the Multi-purpose Hubs. The aim is to develop a method of forming the system of logistical multiplying factors determine the role of each of the types in the technologiacal process of distributed Multi-purpose Hubs. Methods: The assessment model for the formation of Distributed Transport Units  can be based on formal methods to predict the behavior of complex systems engineering complexes. Then one of the approaches to the solution of the problem may be the matrix method of technological factors. Results and conclusions: The proposed methodology of the selection and validation of logistic coefficients has the practical importance in the models development for assessing the condition and behavior of Distributed Transport.

  16. Porosity determination from 2-D resistivity method in studying the slope failures

    Science.gov (United States)

    Maslinda, Umi; Nordiana, M. M.; Bery, A. A.

    2017-07-01

    Slope failures have become the main focus for infrastructures development on hilly areas in Malaysia especially the development of tourism and residential. Lack of understanding and information of the subsoil conditions and geotechnical issues are the main cause of the slope failures. The failures happened are due to a combination of few factors such as topography, climate, geology and land use. 2-D resistivity method was conducted at the collapsed area in Selangor. The 2-D resistivity was done to study the instability of the area. The collapsed occurred because of the subsurface materials was unstable. Pole-dipole array was used with 5 m minimum electrode spacing for the 2-D resistivity method. The data was processed using Res2Dinv software and the porosity was calculated using Archie's law equation. The results show that the saturated zone (1-100 Ωm), alluvium or highly weathered rock (100-1000 Ωm), boulders (1600-7000 Ωm) and granitic bedrock (>7000 Ωm). Generally, the slope failures or landslides occur during the wet season or after rainfall. It is because of the water infiltrate to the slope and cause the saturation of the slope which can lead to landslides. Then, the porosity of saturated zone is usually high because of the water content. The area of alluvium or highly weathered rock and saturated zone have high porosity (>20%) and the high porosity also dominated at almost all the collapsed area which means that the materials with porosity >20% is potential to be saturated, unstable and might trigger slope failures.

  17. SPARK: Sparsity-based analysis of reliable k-hubness and overlapping network structure in brain functional connectivity.

    Science.gov (United States)

    Lee, Kangjoo; Lina, Jean-Marc; Gotman, Jean; Grova, Christophe

    2016-07-01

    Functional hubs are defined as the specific brain regions with dense connections to other regions in a functional brain network. Among them, connector hubs are of great interests, as they are assumed to promote global and hierarchical communications between functionally specialized networks. Damage to connector hubs may have a more crucial effect on the system than does damage to other hubs. Hubs in graph theory are often identified from a correlation matrix, and classified as connector hubs when the hubs are more connected to regions in other networks than within the networks to which they belong. However, the identification of hubs from functional data is more complex than that from structural data, notably because of the inherent problem of multicollinearity between temporal dynamics within a functional network. In this context, we developed and validated a method to reliably identify connectors and corresponding overlapping network structure from resting-state fMRI. This new method is actually handling the multicollinearity issue, since it does not rely on counting the number of connections from a thresholded correlation matrix. The novelty of the proposed method is that besides counting the number of networks involved in each voxel, it allows us to identify which networks are actually involved in each voxel, using a data-driven sparse general linear model in order to identify brain regions involved in more than one network. Moreover, we added a bootstrap resampling strategy to assess statistically the reproducibility of our results at the single subject level. The unified framework is called SPARK, i.e. SParsity-based Analysis of Reliable k-hubness, where k-hubness denotes the number of networks overlapping in each voxel. The accuracy and robustness of SPARK were evaluated using two dimensional box simulations and realistic simulations that examined detection of artificial hubs generated on real data. Then, test/retest reliability of the method was assessed

  18. Doktoritööd : [2007, Boriss Bazanov jt.

    Index Scriptorium Estoniae

    2007-01-01

    7. sept. kaitses Boriss Bazanov doktoritööd teemal "Tehnika ja taktika integratiivne käsitlus korvpalli õpi-treeningprotsessis"; 3. sept. kaitses Grigori Utgof doktoritööd teemal "Süntaktiise tempo probleem"; 30. aug. kaitses Marge Unt doktoritööd teemal "Üleminek koolist tööle laienenud Euroopas"

  19. Synthesis of cefepime-d3 and cefepime-d8

    International Nuclear Information System (INIS)

    Kamachi, Hajime; Okita, Takaaki; Tsuno, Takashi; Naito, Takayuki

    1990-01-01

    Synthesis of cefepime-d 3 (6a) and cefepime-d 8 (6b) is described. Diphenylmethyl 7-benzylideneamino-3-chloromethyl-3-cephem-4-carboxylate (2) was treated with sodium iodide to afford the iodide 3, which was without isolation, allowed to react with N-methyl-d 3 -pyrrolidine to give the quaternary salt 4a. Deblocking of 4a with HCO 2 H and HCl gave 7-amino-3-(N-methyl-d3-pyrrolidinio)methyl-3-cephem-4-carboxylate hydrochloride (5a). Acylation of 5a with benzotriazol-1-yl (Z)-2-(2-aminothiazol-4-yl)-2-methoxyiminoacetate followed by treatment with dil. H 2 SO 4 afforded 6a sulfate. In the same way, 6b was synthesized using N-methyl-pyrrolidine-d 8 . (author)

  20. Surface-micromachined rotatable member having a low-contact-area hub

    Science.gov (United States)

    Rodgers, M. Steven; Sniegowski, Jeffry J.; Krygowski, Thomas W.

    2003-11-18

    A surface-micromachined rotatable member formed on a substrate and a method for manufacturing thereof are disclosed. The surface-micromachined rotatable member, which can be a gear or a rotary stage, has a central hub, and an annulus connected to the central hub by an overarching bridge. The hub includes a stationary axle support attached to the substrate and surrounding an axle. The axle is retained within the axle support with an air-gap spacing therebetween of generally 0.3 .mu.m or less. The rotatable member can be formed by alternately depositing and patterning layers of a semiconductor (e.g. polysilicon or a silicon-germanium alloy) and a sacrificial material and then removing the sacrificial material, at least in part. The present invention has applications for forming micromechanical or microelectromechanical devices requiring lower actuation forces, and providing improved reliability.

  1. Surface--micromachined rotatable member having a low-contact-area hub

    Science.gov (United States)

    Rodgers, M. Steven; Sniegowski, Jeffry J.

    2002-01-01

    A surface-micromachined rotatable member formed on a substrate and a method for manufacturing thereof are disclosed. The surface-micromachined rotatable member, which can be a gear or a rotary stage, has a central hub, and an annulus connected to the central hub by an overarching bridge. The hub includes a stationary axle support attached to the substrate and surrounding an axle. The axle is retained within the axle support with an air-gap spacing therebetween of generally 0.3 .mu.m or less. The rotatable member can be formed by alternately depositing and patterning layers of a semiconductor (e.g. polysilicon or a silicon-germanium alloy) and a sacrificial material and then removing the sacrificial material, at least in part. The present invention has applications for forming micromechanical or microelectromechanical devices requiring lower actuation forces, and providing improved reliability.

  2. A Collaborative Scheduling Model for the Supply-Hub with Multiple Suppliers and Multiple Manufacturers

    Directory of Open Access Journals (Sweden)

    Guo Li

    2014-01-01

    Full Text Available This paper investigates a collaborative scheduling model in the assembly system, wherein multiple suppliers have to deliver their components to the multiple manufacturers under the operation of Supply-Hub. We first develop two different scenarios to examine the impact of Supply-Hub. One is that suppliers and manufacturers make their decisions separately, and the other is that the Supply-Hub makes joint decisions with collaborative scheduling. The results show that our scheduling model with the Supply-Hub is a NP-complete problem, therefore, we propose an auto-adapted differential evolution algorithm to solve this problem. Moreover, we illustrate that the performance of collaborative scheduling by the Supply-Hub is superior to separate decision made by each manufacturer and supplier. Furthermore, we also show that the algorithm proposed has good convergence and reliability, which can be applicable to more complicated supply chain environment.

  3. A Collaborative Scheduling Model for the Supply-Hub with Multiple Suppliers and Multiple Manufacturers

    Science.gov (United States)

    Lv, Fei; Guan, Xu

    2014-01-01

    This paper investigates a collaborative scheduling model in the assembly system, wherein multiple suppliers have to deliver their components to the multiple manufacturers under the operation of Supply-Hub. We first develop two different scenarios to examine the impact of Supply-Hub. One is that suppliers and manufacturers make their decisions separately, and the other is that the Supply-Hub makes joint decisions with collaborative scheduling. The results show that our scheduling model with the Supply-Hub is a NP-complete problem, therefore, we propose an auto-adapted differential evolution algorithm to solve this problem. Moreover, we illustrate that the performance of collaborative scheduling by the Supply-Hub is superior to separate decision made by each manufacturer and supplier. Furthermore, we also show that the algorithm proposed has good convergence and reliability, which can be applicable to more complicated supply chain environment. PMID:24892104

  4. A note on hierarchical hubbing for a generalization of the VPN problem

    NARCIS (Netherlands)

    N.K. Olver (Neil)

    2016-01-01

    textabstractRobust network design refers to a class of optimization problems that occur when designing networks to efficiently handle variable demands. In this context, Fréchette et al. (2013) recently explored hierarchical hubbing: a routing strategy involving a multiplicity of "hubs" connected to

  5. A note on hierarchical hubbing for a generalization of the VPN problem

    NARCIS (Netherlands)

    Olver, Neil

    2016-01-01

    Robust network design refers to a class of optimization problems that occur when designing networks to efficiently handle variable demands. In this context, Fréchette et al. (2013) recently explored hierarchical hubbing: a routing strategy involving a multiplicity of "hubs" connected to terminals

  6. Robust Energy Hub Management Using Information Gap Decision Theory

    DEFF Research Database (Denmark)

    Javadi, Mohammad Sadegh; Anvari-Moghaddam, Amjad; Guerrero, Josep M.

    2017-01-01

    This paper proposes a robust optimization framework for energy hub management. It is well known that the operation of energy systems can be negatively affected by uncertain parameters, such as stochastic load demand or generation. In this regard, it is of high significance to propose efficient...... tools in order to deal with uncertainties and to provide reliable operating conditions. On a broader scale, an energy hub includes diverse energy sources for supplying both electrical load and heating/cooling demands with stochastic behaviors. Therefore, this paper utilizes the Information Decision Gap...

  7. Fast collimated neutron flux measurement using stilbene scintillator and flashy analog-to-digital converter in JT-60U

    International Nuclear Information System (INIS)

    Ishikawa, M.; Itoga, T.; Okuji, T.; Nakhostin, M.; Shinohara, K.; Hayashi, T.; Sukegawa, A.; Baba, M.; Nishitani, T.

    2006-01-01

    A line-integrated neutron emission profile is routinely measured using the radial neutron collimator system in JT-60U tokamak. Stilbene neuron detectors (SNDs), which combine a stilbene organic crystal scintillation detector (SD) with an analog neutron-gamma pulse shape discrimination (PSD) circuit, have been used to measure collimated neutron flux. Although the SND has many advantages as a neutron detector, the maximum count rate is limited up to ∼1x10 5 counts/s due to the analog PSD circuit. To overcome this issue, a digital signal processing system (DSPS) using a flash analog-to-digital converter (Acqiris DC252, 8 GHz, 10 bits) has been developed at Cyclotron and Radioisotope Center in Tohoku University. In this system anode signals from photomultiplier of the SD are directory stored and digitized. Then, the PSD between neutrons and gamma rays is performed using software. The DSPS has been installed in the vertical neutron collimator system in JT-60U and applied to deuterium experiments. It is confirmed that the PSD is sufficiently performed and collimated neutron flux is successfully measured with count rate up to ∼5x10 5 counts/s without the effect of pileup of detected pulses. The performance of the DSPS as a neutron detector, which supersedes the SND, is demonstrated

  8. Development of Gyrotron and JT-60U EC heating system for fusion reactor

    International Nuclear Information System (INIS)

    Sakamoto, K.; Kasugai, A.; Ikeda, Yo.

    2003-01-01

    The progress of ECH technology, for ITER and JT-60U tokamak, are presented. In the development of gyrotron, 0.9MW/9.2sec, 0.5MW/30sec, 0.3MW/60sec, etc. have been demonstrated at 170GHz. At 110GHz, 1.3MW/1.2sec, 1.2MW/4.1sec, 1MW/5sec were obtained. It is found that the reduction of the stray radiation and the enhancement of cooling capability are keys for CW operation. Four 110GHz gyrotrons are under operation in the ECH system of JT-60U. The power up to approximately 3MW/2.7sec was injected into the plasma through the poloidally movable mirrors, and contributed to the electron heating up to 26keV(n e ∼0.5x10 13 cm -3 ), and the suppression of the neo-classical tearing mode. (author)

  9. Development of gyrotron and JT-60U EC heating system for fusion reactor

    International Nuclear Information System (INIS)

    Sakamoto, K.; Kasugai, A.; Ikeda, Yo.

    2003-01-01

    The progress of ECH technology, for ITER and JT-60U tokamak, are presented. In the development of gyrotron, 0.9MW/9.2sec, 0.5MW/30sec, 0.3MW/60sec, etc. have been demonstrated at 170GHz. At 110GHz, 1.3MW/1.2sec, 1.2MW/4. 1sec. 1MW/5sec were obtained. It is found that the reduction of the stray radiation and the enhancement of cooling capability are keys for CW operation. Four 110GHz gyrotrons are under operation in the ECH system of JT-60U. The power up to approximately 3MW/2.7sec was injected into the plasma through the poloidally movable mirrors, and contributed to the electron heating up to 26keV(n e ∼0.5x10 13 cm -3 ), and the suppression of the neo-classical tearing mode. (author)

  10. Structural design of vacuum bulkheads in piping penetration for the cryostat base of JT-60SA

    International Nuclear Information System (INIS)

    Nakamura, Shigetoshi; Shibama, Yusuke K.; Masaki, Kei

    2016-11-01

    This study examined the structure of the boundary box that is capable of installing the cryostat base of JT-60SA in a narrow space. Since other devices stand close in the neighborhood, it was designed to fit within a limited space to avoid interference. Spatial limitation and generated stress caused by each load were used as design conditions. From the calculation results of the generated stress with respect to each load, the maximum stress is generated by the displacement of the pipeline associated with the displacement of the vacuum container at the time of earthquake and 200degC baking, so bellows were designed to absorb the displacement of the piping. It was confirmed through 3-D finite element analysis that this generated stress is less than the allowable stress and there is no problem in structural integrity. This paper explained the composition of major equipment of JT-60SA and the structure of cryostat base. In the structural analysis of the boundary box, consideration was given to the pressure difference during vacuum closure or abnormal events, temperature distribution, pipe displacement associated with the deformation of vacuum vessel, and seismic load. As a result of finite element analysis, it was confirmed that the displacement amount and temperature distribution during plasma operation and baking were within the allowable range. In addition, the maximum stress during cryostat helium leak was also within the allowable range. (A.O.)

  11. Large intragenic deletion of CDC73 (exons 4-10) in a three-generation hyperparathyroidism-jaw tumor (HPT-JT) syndrome family.

    Science.gov (United States)

    Guarnieri, Vito; Seaberg, Raewyn M; Kelly, Catherine; Jean Davidson, M; Raphael, Simon; Shuen, Andrew Y; Baorda, Filomena; Palumbo, Orazio; Scillitani, Alfredo; Hendy, Geoffrey N; Cole, David E C

    2017-08-03

    Inactivating mutations of CDC73 cause Hyperparathyroidism-Jaw Tumour syndrome (HPT-JT), Familial Isolated Hyperparathyroidism (FIHP) and sporadic parathyroid carcinoma. We conducted CDC73 mutation analysis in an HPT-JT family and confirm carrier status of the proband's daughter. The proband had primary hyperparathyroidism (parathyroid carcinoma) and uterine leiomyomata. Her father and daughter had hyperparathyroidism (parathyroid adenoma) but no other manifestations of HPT-JT. CDC73 mutation analysis (sequencing of all 17 exons) and whole-genome copy number variation (CNV) analysis was done on leukocyte DNA of the three affecteds as well as the proband's unaffected sister. A novel deletion of exons 4 to 10 of CDC73 was detected by CNV analysis in the three affecteds. A novel insertion in the 5'UTR (c.-4_-11insG) that co-segregated with the deletion was identified. By in vitro assay the 5'UTR insertion was shown to significantly impair the expression of the parafibromin protein. Screening for the mutated CDC73 confirmed carrier status in the proband's daughter and the biochemistry and ultrasonography led to pre-emptive surgery and resolution of the hyperparathyroidism. A novel gross deletion mutation in CDC73 was identified in a three-generation HPT-JT family emphasizing the importance of including screening for large deletions in the molecular diagnostic protocol.

  12. Innovation Hub How-To

    DEFF Research Database (Denmark)

    Berger, Andreas; Brem, Alexander

    2016-01-01

    in establishing an innovative environment: carefully considering the decision to set up such a center, hiring the right people, designing a framework for effective output, creating a buffer from bureaucratic distractions, securing a leader to champion the effort, focusing on business outcomes, fostering...... disruptive over incremental innovation, and being patient. Regardless of where an innovation hub is established, the key to success lies in hiring creative, intrinsically motivated staff and then giving them the freedom to do what they do best....

  13. Exploring hubness in Regional Trade Agreements

    NARCIS (Netherlands)

    Vaal, A. de

    2016-01-01

    In the plethora of Regional Trade Agreements (RTAs) some countries take in a more central position than others in the sense that some countries are much more engaged with other countries through RTAs. Furthermore, the position of some countries is that of a hub: they have (many) trade

  14. Gas and LNG pricing and trading hub in East Asia: An introduction

    Directory of Open Access Journals (Sweden)

    Xunpeng Shi

    2016-10-01

    Full Text Available This paper summarizes the four papers in the special issues on ‘Gas and LNG pricing and trading hub in East Asia’. The papers examine lessons and experience from European hub development, other commodity, the Japanese history on developing of futures markets and inter-fuel substitution in East Asia. The papers finds that liquid futures market is the key to formulate benchmark prices while a well-developed spot market is the foundation; political will and strong leadership are required to overcome the power of incumbents and to restructure the gas market that impede the the development of competitive markets; and East Asia needs to develop its indigenous gas or LNG trading hubs even in low oil prices period and its developing market allows easier changes in new contracts than in existing ones. This hub development requires governments to go through tough domestic market reforms, including liberalization and cooperation with each other and with gas exporters.

  15. Medium-term energy hub management subject to electricity price and wind uncertainty

    International Nuclear Information System (INIS)

    Najafi, Arsalan; Falaghi, Hamid; Contreras, Javier; Ramezani, Maryam

    2016-01-01

    Highlights: • A new model for medium-term energy hub management is proposed. • Risk aversion is considered in medium-term energy hub management. • Stochastic programing is used to solve the medium-term energy hub management problem. • Electricity price and wind uncertainty are considered. - Abstract: Energy hubs play an important role in implementing multi-carrier energy systems. More studies are required in both their modeling and operating aspects. In this regard, this paper attempts to develop medium-term management of an energy hub in restructured power systems. A model is presented to manage an energy hub which has electrical energy and natural gas as inputs and electrical and heat energy as outputs. Electricity is procured in various ways, either purchasing it from a pool-based market and bilateral contracts, or producing it from a Combined Heat and Power (CHP) unit, a diesel generator unit and Wind Turbine Generators (WTGs). Pool prices and wind turbine production are subject to uncertainty, which makes energy management a complex puzzle. Heat demand is also procured by a furnace and a CHP unit. Energy hub managers should make decisions whether to purchase electricity from the electricity market and gas from the gas network or to produce electricity using a set of generators to meet the electrical and heat demands in the presence of uncertainties. The energy management objective is to minimize the total cost subject to several technical constraints using stochastic programming. Conditional Value at Risk (CVaR), a well-known risk measure, is used to reduce the unfavorable risk of costs. In doing so, the proposed model is illustrated using a sample test case with actual prices, load and wind speed data. The results show that the minimum cost is obtained by the best decisions involving the electricity market and purchasing natural gas for gas facilities. Considering risk also increases the total expected cost and decreases the CVaR.

  16. Machine performance and its effects on experiments in JT-60U

    International Nuclear Information System (INIS)

    Kondo, I.

    1995-01-01

    The operational results of JT-60U were reviewed in light of the strategy made at the design stage. The operational plan for better confinement shifted from that of low q to high poloidal beta plasma configuration with higher q value according to the revealed machine properties. Some technical and operational skills helped bring about the recent results out of the machine. (orig.)

  17. Design of JT-60SA magnets and associated experimental validations

    International Nuclear Information System (INIS)

    Zani, L.; Barabaschi, P.; Peyrot, M.; Meunier, L.; Tomarchio, V.; Duglue, D.; Decool, P.; Torre, A.; Marechal, J.L.; Della Corte, A.; Di Zenobio, A.; Muzzi, L.; Cucchiaro, A.; Turtu, S.; Ishida, S.; Yoshida, K.; Tsuchiya, K.; Kizu, K.; Murakami, H.

    2011-01-01

    In the framework of the JT-60SA project, aiming at upgrading the present JT-60U tokamak toward a fully superconducting configuration, the detailed design phase led to adopt for the three main magnet systems a brand new design. Europe (EU) is expected to provide to Japan (JA) the totality of the toroidal field (TF) magnet system, while JA will provide both Equilibrium field (EF) and Central Solenoid (CS) systems. All magnet designs were optimized trough the past years and entered in parallel into extensive experimentally-based phases of concept validation, which came to maturation in the years 2009 and 2010. For this, all magnet systems were investigated by mean of dedicated samples, e.g. conductor and joint samples designed, manufactured and tested at full scale in ad hoc facilities either in EU or in JA. The present paper, after an overall description of magnet systems layouts, presents in a general approach the different experimental campaigns dedicated to qualification design and manufacture processes of either coils, conductors and electrical joints. The main results with the associated analyses are shown and the main conclusions presented, especially regarding their contribution to consolidate the triggering of magnet mass production. The status of respective manufacturing stages in EU and in JA are also evoked. (authors)

  18. Hub network design for sparse travel demand within the African aviation industry

    CSIR Research Space (South Africa)

    Ssamula, B

    2007-07-01

    Full Text Available and analysed to reveal that the best option for a hub network is the so-called geo-political network. A geo-political network is where hubs are created in the North, South, East and West of Africa, at airports with strong political influence, high passenger...

  19. Design and Analysis of Wind Turbine Blade Hub using Aluminium Alloy AA 6061-T6

    Science.gov (United States)

    Ravikumar, S.; Jaswanthvenkatram, V.; Sai kumar, Y. J. N. V.; Sohaib, S. Md.

    2017-05-01

    This work presents the design and analysis of horizontal axis wind turbine blade hub using different material. The hub is very crucial part of the wind turbine, which experience the loads from the blades and the loads were transmitted to the main shaft. At present wind turbine is more expensive and weights more than a million pounds, with the nacelle, rotor hub and blades accounting for most of the weight. In this work Spheroidal graphite cast iron GGG 40.3 is replaced by aluminium alloy 6061-T6 to enhance the casting properties and also to improve the strength-weight ratio. This transition of material leads to reduction in weight of the wind turbine. All the loads caused by wind and extreme loads on the blades are transferred to the hub. Considering the IEC 61400-1 standard for defining extreme loads on the hub the stress and deflection were calculated on the hub by using Finite element Analysis. Result obtained from ANSYS is compared and discussed with the existing design.

  20. External corrosion of tanks 8D-1 and 8D-2. Final report

    International Nuclear Information System (INIS)

    Mackey, D.B.; Westerman, R.E.

    1995-05-01

    Tanks 8D-1 and 8D-2 at the West Valley Nuclear Services (WVNS) site, West Valley, New York, rest on layers of perlite brick contained within steel pans. The pans tend to collect water, which can contact the tanks directly and which also can be ''wicked'' to the external surfaces of the tank through the perlite brick. The presence of air in the tank vault is conducive to the formation of oxygen concentration cells, which can promote localized corrosion of the carbon steel tank wall. Pacific Northwest Laboratory conducted an experiment to estimate the extent to which the external surfaces of the tanks could have corroded in the 30 years since their construction. Specimens of carbon steel, similar to that used in the tank construction, were partially embedded in an upright position in particulate perlite in closed containers. The water line in the containers.was maintained at two levels: above the perlite level (high water level tests) and below the bottoms of the specimens (low water level tests). The water used in the tests was obtained from the pan of tank 8D-1. The containers were maintained in an aerated condition. Specimens were examined after 3-, 6-, 12-, 18-, 24-, and 30-month exposures

  1. KINEMATIC ANALYSES OF THE GOLF SWING HUB PATH AND ITS ROLE IN GOLFER/CLUB KINETIC TRANSFERS

    Directory of Open Access Journals (Sweden)

    Steven M. Nesbit

    2009-06-01

    Full Text Available This study analyzed the fundamental geometric and kinematic characteristics of the swing hub path of the golf shot for four diverse subjects. In addition, the role of the hub path geometry in transferring the kinetic quantities from the golfer to the club were investigated. The hub path was found to have a complex geometry with significantly changing radii, and a constantly moving center-of-curvature during the downswing for all subjects. While the size and shape of the hub path differed considerably among the subjects, a three phase radius-based pattern was revealed that aligned with distinct stages of the downswing. Artificially controlling and optimizing the hub path of the better golfer in the group indicated that a non-circular hub path was superior to a constant radius path in minimizing the kinetic loading while generating the highest possible club head velocity. The shape and purpose of the hub path geometry appears to result from a complex combination of achieving equilibrium between the golfer and the club, and a purposeful configuring of the path to control the outward movement of the club while minimizing the kinetic loading on the golfer yet transferring the maximum kinetic quantities to the club. Describing the downswing relative to the hub path phasing is presented and was found to be informative since the phases align with significant swing, kinetic and kinematic markers. These findings challenge golf swing modeling methodologies which fix the center-of-curvature of the hub path thus constraining it to constant radius motion

  2. Using street view imagery for 3-D survey of rock slope failures

    Directory of Open Access Journals (Sweden)

    J. Voumard

    2017-12-01

    Full Text Available We discuss here different challenges and limitations of surveying rock slope failures using 3-D reconstruction from image sets acquired from street view imagery (SVI. We show how rock slope surveying can be performed using two or more image sets using online imagery with photographs from the same site but acquired at different instances. Three sites in the French alps were selected as pilot study areas: (1 a cliff beside a road where a protective wall collapsed, consisting of two image sets (60 and 50 images in each set captured within a 6-year time frame; (2 a large-scale active landslide located on a slope at 250 m from the road, using seven image sets (50 to 80 images per set from five different time periods with three image sets for one period; (3 a cliff over a tunnel which has collapsed, using two image sets captured in a 4-year time frame. The analysis include the use of different structure from motion (SfM programs and a comparison between the extracted photogrammetric point clouds and a lidar-derived mesh that was used as a ground truth. Results show that both landslide deformation and estimation of fallen volumes were clearly identified in the different point clouds. Results are site- and software-dependent, as a function of the image set and number of images, with model accuracies ranging between 0.2 and 3.8 m in the best and worst scenario, respectively. Although some limitations derived from the generation of 3-D models from SVI were observed, this approach allowed us to obtain preliminary 3-D models of an area without on-field images, allowing extraction of the pre-failure topography that would not be available otherwise.

  3. Increased tissue factor, MMP-8, and D-dimer expression in diabetic patients with unstable advanced carotid atherosclerosis

    Directory of Open Access Journals (Sweden)

    Jerzy Krupinski

    2007-09-01

    Full Text Available Jerzy Krupinski1,2, Marta M Turu1,2, M Angels Font1, Nesser Ahmed3, Matthew Sullivan3, Ana Luque1,2, Francisco Rubio1, Lina Badimon2, Mark Slevin31Department of Neurology, Stroke Unit, University Hospital of Bellvitge (HUB, Fundacio IDIBELL, Barcelona, Spain; 2Cardiovascular Research Centre, IIBB/CSIC-HSCSP-UAB, Barcelona, Spain; 3School of Biology, Chemistry and Health Science, Manchester Metropolitan University, Manchester, United KingdomAbstract: Advanced atherogenesis is characterized by the presence of markers of enhanced prothrombotic capacity, attenuated fibrinolysis, and by clinical conditions associated with defective coagulation. Diabetes may be associated with enhanced lesion instability and atherosclerotic plaque rupture. Plaques obtained from 206 patients undergoing carotid endarterectomy were divided into diabetic (type 2 and nondiabetic and analyzed by Western blotting and immunohistochemistry to detect tissue factor (TF, metalloproteinases (MMP-2, -8, -9, and fibrin/fibrinogen related antigens, and in situ zymography to detect MMP activity. Plasma samples were quantified for TF procoagulant activity, C-reactive protein, fibrinogen and D-dimer. Diabetic and symptomatic patients with hypoechogenic plaques had increased plasma TF activity and D-dimer, compared with those with hyperechogenic plaques (p = 0.03, p = 0.007, respectively. Diabetic, symptomatic patients had higher plasma D-dimer levels than asymptomatic patients (p = 0.03. There was a significant correlation between intramural TF levels and D-dimer in diabetic patients with symptomatic disease (p = 0.001, r2 = 0.4. In diabetic patients, plasma fibrinogen levels were higher in patients with hypoechogenic plaques (p = 0.007. Diabetic patients with ulcerated plaques had higher plasma D-dimer and MMP-8 levels than those with fibrous plaques (p = 0.02, p = 0.01, respectively. This data suggests that currently available circulating markers may be clinically useful to select

  4. Abnormal hubs of white matter networks in the frontal-parieto circuit contribute to depression discrimination via pattern classification.

    Science.gov (United States)

    Qin, Jiaolong; Wei, Maobin; Liu, Haiyan; Chen, Jianhuai; Yan, Rui; Hua, Lingling; Zhao, Ke; Yao, Zhijian; Lu, Qing

    2014-12-01

    Previous studies had explored the diagnostic and prognostic value of the structural neuroimaging data of MDD and treated the whole brain voxels, the fractional anisotropy and the structural connectivity as classification features. To our best knowledge, no study examined the potential diagnostic value of the hubs of anatomical brain networks in MDD. The purpose of the current study was to provide an exploratory examination of the potential diagnostic and prognostic values of hubs of white matter brain networks in MDD discrimination and the corresponding impaired hub pattern via a multi-pattern analysis. We constructed white matter brain networks from 29 depressions and 30 healthy controls based on diffusion tensor imaging data, calculated nodal measures and identified hubs. Using these measures as features, two types of feature architectures were established, one only included hubs (HUB) and the other contained both hubs and non hubs. The support vector machine classifiers with Gaussian radial basis kernel were used after the feature selection. Moreover, the relative contribution of the features was estimated by means of the consensus features. Our results presented that the hubs (including the bilateral dorsolateral part of superior frontal gyrus, the left middle frontal gyrus, the bilateral middle temporal gyrus, and the bilateral inferior temporal gyrus) played an important role in distinguishing the depressions from healthy controls with the best accuracy of 83.05%. Moreover, most of the HUB consensus features located in the frontal-parieto circuit. These findings provided evidence that the hubs could be served as valuable potential diagnostic measure for MDD, and the hub-concentrated lesion distribution of MDD was primarily anchored within the frontal-parieto circuit. Copyright © 2014 Elsevier Inc. All rights reserved.

  5. TYPE PROJECTS HUB - AN INTERNATIONAL MODEL OF DEVELOPMENT OF THE ENTREPRENEURIAL ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Rozalia Nistor

    2014-06-01

    Full Text Available Impact Hub is a global network of local spaces and communities designed to facilitate sustainable impact through collaboration. Local Impact Hubs are autonomous companies that offer co-working spaces, programming, events platforms, and communities of individuals and organizations with ideas to build a better world. Hub was established in 2005 in London with the aim of creating a space dedicated to inspire, connect and enable people to achieve a sustainable entrepreneurial idea. The idea was simple: There are a lot of people with good ideas for a "better world". What seem to be missing are places to help these people to move from intent to action and to find like-minded for a greater impact. In Romania about four years ago, first opened in Bucharest office space hubs in Romania (for entrepreneurs in technology and business where teams from different companies could collaborate. The idea to open a hub in Bucharest focused on social innovation and entrepreneurship appeared some time ago in the context in which part of the team now has worked since 2010 at the initiation and growth of a community to support social entrepreneurship. In all this diversity, there is a common mission: “we can create if we put all our innovation capacity in the common goal to create a positive impact through our work?”

  6. Disrupted nodal and hub organization account for brain network abnormalities in Parkinson’s disease

    Directory of Open Access Journals (Sweden)

    Yuko Koshimori

    2016-11-01

    Full Text Available The recent application of graph theory to brain networks promises to shed light on complex diseases such as Parkinson’s disease. This study aimed to investigate functional changes in sensorimotor and cognitive networks in parkinsonian patients, with a focus on inter- and intra-connectivity organization in the disease-associated nodal and hub regions using the graph theoretical analyses. Resting-state functional MRI data of a total of 65 participants, including 23 healthy controls and 42 patients, were investigated in 120 nodes for local efficiency, betweenness centrality, and degree. Hub regions were identified in the healthy control and patient groups. We found nodal and hub changes in patients compared with healthy controls, including the right pre-supplementary motor area, left anterior insula, bilateral mid-insula, bilateral dorsolateral prefrontal cortex, and right caudate nucleus. In general, nodal regions within the sensorimotor network (i.e. right pre-supplementary motor area and right mid-insula displayed weakened connectivity, with the former node associated with more severe bradykinesia, and impaired integration with default mode network regions. The left mid-insula also lost its hub properties in patients. Within the executive networks, the left anterior insular cortex lost its hub properties in patients, while a new hub region was identified in the right caudate nucleus, paralleled by an increased level of inter- and intra-connectivity in the bilateral dorsolateral prefrontal cortex possibly representing compensatory mechanisms. These findings highlight the diffuse changes in nodal organization and regional hub disruption accounting for the distributed abnormalities across brain networks and the clinical manifestations of Parkinson’s disease.

  7. The design study of the JT-60SU device. No. 4. The vacuum vessel and cryostat of JT-60SU

    International Nuclear Information System (INIS)

    Neyatani, Yuzuru; Ushigusa, Kenkichi; Tobita, Kenji

    1997-03-01

    The vacuum vessel and the cryostat for the JT-60 Super Upgrade (JT-60SU) have been designed. Two types of the complex materials for the vacuum vessel were chosen on the basis of the avoidance of tritium occlusion and the low irradiation, i.e. (1) SUS316 covered by tungsten plate (30mm thickness) as a γ-ray shielding, (2) Ti-6Al-4V alloy covered by SUS430 plate (1mm thickness) as a tritium protector. Selecting the double skin type of vacuum vessel with toroidally continued structure gave the basic design of the vacuum vessel satisfying the design criteria of the vessel strength for the electromagnetic force, heat load and the property of radiation shielding. The characteristics of the SUS316 covered by tungsten plate type is that as the tungsten can shield the γ-ray, the dose rate inside the vacuum vessel during the maintenance can reduce effectively. The advantage of the Ti-6Al-4V alloy covered by SUS430 plate type vacuum vessel is the quick reduction of the radioactive isotope because of no production of the isotopes with long half-life periods. Channel type and vertical type of the divertor were designed. The sector type of toroidally separated structure was selected for the remote handling. The material of the armor plate was not determined because no material endure the high heat load on the divertor. The cryostat composing the dome and the tank was designed. The electromagnetic force by the eddy current, generated at the plasma start up phase and at the quench of CS super-conducting coil, were small compared to the force produced by the stress limit. (author)

  8. Analysis and Modeling of Ground Operations at Hub Airports

    Science.gov (United States)

    Atkins, Stephen (Technical Monitor); Andersson, Kari; Carr, Francis; Feron, Eric; Hall, William D.

    2000-01-01

    Building simple and accurate models of hub airports can considerably help one understand airport dynamics, and may provide quantitative estimates of operational airport improvements. In this paper, three models are proposed to capture the dynamics of busy hub airport operations. Two simple queuing models are introduced to capture the taxi-out and taxi-in processes. An integer programming model aimed at representing airline decision-making attempts to capture the dynamics of the aircraft turnaround process. These models can be applied for predictive purposes. They may also be used to evaluate control strategies for improving overall airport efficiency.

  9. Application of hydraulically assembled shaft coupling hubs to large agitators

    International Nuclear Information System (INIS)

    Murray, W.E.; Anderson, T.D.; Bethmann, H.K.

    1991-01-01

    This paper describes the basis for and implementation of hydraulically assembled shaft coupling hubs for large tank-mounted agitators. This modification to the original design was intended to minimize maintenance personnel exposure to ionizing radiation and also provide for disassembly capability without damage to shafts or hubs. In addition to realizing these objectives, test confirmed that the modified couplings reduced agitator shaft end runouts approximately 65%, thereby reducing bearing loads and increasing service life, a significant enhancement for a nuclear facility. 5 refs

  10. Why do European companies have Innovation Hubs in Silicon Valley

    DEFF Research Database (Denmark)

    Berger, Andreas; Brem, Alexander

    2017-01-01

    Innovation hubs are gaining high attention in recent years, especially from European companies. Silicon Valley has been deemed as one of the most attractive and successful environments for establishing innovation hubs. This article highlights examples of companies from Europe that made the step...... to California—namely, Volkswagen, Swisscom, BMW, Axel Springer, Munich Re, and Innogy SE (RWE Group). Based on these companies’ experiences, recommendations are given on how companies might approach a setup in Silicon Valley for long-term success....

  11. Complete D =11 embedding of SO(8) supergravity

    Science.gov (United States)

    Varela, Oscar

    2018-02-01

    The truncation formulas of D =11 supergravity on S7 to D =4 N =8 SO(8)-gauged supergravity are completed to include the full nonlinear dependence of the D =11 three-form potential A^ (3 ) on the D =4 fields, and their consistency is shown. The full embedding into A^ (3 ) is naturally expressed in terms of a restricted version, still N =8 but only SL(8)-covariant, of the D =4 tensor hierarchy. The redundancies introduced by this approach are removed at the level of the field strength F^ (4 ) by exploiting D =4 duality relations. Finally, new expressions for the full consistent truncation formulas are given that are explicit in all D =11 and D =4 fields.

  12. Study of the Engine Bird Ingestion Experience of the Boeing 737 Aircraft (October 1986- September 1988)

    Science.gov (United States)

    1990-05-01

    19554CUD CORRIENTES , ARGENTINA S FG 1100 544CN5 CAIRNS, OLD, AUSTRALIA S FG 4850 6049CUX CHIANG MAI, THAILAND N FN 728 435COX COCHIN, INDIA N FGH 5457...ARGENTINA S FGN 154 148 VLI PORT VILA, VANUATU S FGN 251 560 VMS VARANASI, INDIA N FGN 3150 2686 VoEN VERONA, ITALY N FGN 0 3 VIE VIENTIANE, LAOS N FGN 0 52...JIMA, JAPAN NO JT8O 2 MEL MELBOURNE, AUSTRALIA Nc CFM56 3 NONE NONE NONE NC 1 4. JAI JAIPUR, INDIA NO JT8O NC 1 VMS VARANASI, INDIA NO JT8D’ I MAN

  13. Biaxial wheel/hub test facility. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, G.; Grubisic, V. [eds.

    2000-07-01

    The 4{sup th} meeting aims to exchange the experience and knowledge of engineers during several presentations and discussions about new developments required for a reliable, time and cost reducing validation of the wheel/hub assembly. Tremendous development of the wheel performance, described by the ratio of the rated load (kg) versus the wheel weight (kg) had taken place during the last 5000 years. Starting from the ratio of 3 for wooden 2-piece-disc-wheels in Mesopotamia it needed nearly 1000 years to increase the ratio to approx 5 at light-weight spoke wheels for fighting carriages, found in the grave of king Tutenchamon in Egypt. Modern light alloy wheels of commercial vehicles reach values up to 160 kg/kg. Additionally the comlex design of the modern systems for cars and commercial vehicles comprising wheel, brake, hub, bearing, spindle and hub carrier, including different materials and their treatment, fasteners, press-fits, require an appropriate testing procedure. The variable loading conditions, caused by operational wheel forces, brake and torque moments including heating, may result in changing tolerances and press-fits during operation and consequently in different damage mechanisms. This can be simulated in the Biaxial Wheel Test Machine, whereby corresponding load programs are necessary. An overview about all biaxial test machines in usage at the end of 1999 is shown in the introduction. The total number is 17 for cars, 7 for commercial vehicles and 1 for trains. The six presentations of this meeting were consequently concentrated on: (a) recommendations for a standardization of load programs of the German Wheel Committee, (b) the simulation of brake and torque events and (c) the possibility for a numerical stress analyses and fatigue life assessment. (orig./AKF)

  14. Comparative efficiency of wind turbines with different heights of rotor hubs: performance evaluation for Latvia

    International Nuclear Information System (INIS)

    Bezrukovs, V P; Zacepins, A J; Bezrukovs, V V

    2014-01-01

    Performance evaluation of wind turbines (WT) for different heights of the rotor hub is made based on the wind speed and direction data obtained in 2009–2013 on-shore in the north of Latvia using a LOGGER 9200 Symphonie measurement system mounted on a 60 m mast. Based on the measurement analysis results, wind speed distribution curves have been modelled for heights of up to 200 m using power and logarithmic (log) law approximation methods. The curves for the modelled Weibull's parameters are plotted in dependence on height. The efficiency comparison is made for different WT types taking into account the distribution of the wind energy potential in height in the Latvian territory. The annual electric energy production was calculated for the WTs with different heights of rotor hubs. In the calculations the technical data on the following WT types were used: E-3120 (50 kW, hub height 20.5/30.5/36.5/42.7 m), E-33 (330 kW, hub height 37/44/49/50 m), E-48 (800 kW, hub height 50/60/75 m) and E-82 (2.3 MW, hub height of 78/85/98/108/138 m)

  15. Portable Desktop Apps with GitHub Electron

    CERN Multimedia

    CERN. Geneva

    2016-01-01

    Wouldn't it be nice if you could develop applications that work everywhere, regardless of Operating System or Platform? Even better, what if you could employ the same front-end technologies you use for your web/mobile apps? Meet GitHub Electron.

  16. A preliminary assessment of the potential for 'team science' in DOE Energy Innovation Hubs and Energy Frontier Research Centers

    International Nuclear Information System (INIS)

    Boardman, Craig; Ponomariov, Branco

    2011-01-01

    President Obama has called for the development of new energy technologies to address our national energy needs and restore US economic competitiveness. In response, the Department of Energy has established new R and D modalities for energy research and development designed to facilitate collaboration across disciplinary, institutional, and sectoral boundaries. In this research note, we provide a preliminary assessment of the potential for essential mechanisms for coordinated problem solving among diverse actors within two new modalities at the DOE: Energy Innovation Hubs and Energy Frontier Research Centers. - Highlights: → Energy Frontier Research Centers may lack the basic mechanisms for coordinating diverse actors. → Divergent goals across diverse actors may hinder coordination in Energy Innovation Hubs. → The implementation of these and similar energy policies require further investigation.

  17. A novel method to identify hub pathways of rheumatoid arthritis based on differential pathway networks.

    Science.gov (United States)

    Wei, Shi-Tong; Sun, Yong-Hua; Zong, Shi-Hua

    2017-09-01

    The aim of the current study was to identify hub pathways of rheumatoid arthritis (RA) using a novel method based on differential pathway network (DPN) analysis. The present study proposed a DPN where protein‑protein interaction (PPI) network was integrated with pathway‑pathway interactions. Pathway data was obtained from background PPI network and the Reactome pathway database. Subsequently, pathway interactions were extracted from the pathway data by building randomized gene‑gene interactions and a weight value was assigned to each pathway interaction using Spearman correlation coefficient (SCC) to identify differential pathway interactions. Differential pathway interactions were visualized using Cytoscape to construct a DPN. Topological analysis was conducted to identify hub pathways that possessed the top 5% degree distribution of DPN. Modules of DPN were mined according to ClusterONE. A total of 855 pathways were selected to build pathway interactions. By filtrating pathway interactions of weight values >0.7, a DPN with 312 nodes and 791 edges was obtained. Topological degree analysis revealed 15 hub pathways, such as heparan sulfate/heparin‑glycosaminoglycan (HS‑GAG) degradation, HS‑GAG metabolism and keratan sulfate degradation for RA based on DPN. Furthermore, hub pathways were also important in modules, which validated the significance of hub pathways. In conclusion, the proposed method is a computationally efficient way to identify hub pathways of RA, which identified 15 hub pathways that may be potential biomarkers and provide insight to future investigation and treatment of RA.

  18. Hub location problems in transportation networks

    DEFF Research Database (Denmark)

    Gelareh, Shahin; Nickel, Stefan

    2011-01-01

    In this paper we propose a 4-index formulation for the uncapacitated multiple allocation hub location problem tailored for urban transport and liner shipping network design. This formulation is very tight and most of the tractable instances for MIP solvers are optimally solvable at the root node....... also introduce fixed cost values for Australian Post (AP) dataset....

  19. Role of governance in creating a commodity hub: A comparative analysis

    Directory of Open Access Journals (Sweden)

    M.P. Haris

    2016-10-01

    Full Text Available The body of work on natural gas hubs has been expanding rapidly in recent years, with most of the current work examining the creation of gas hubs focusing on either the European experience or the North American experience. In this paper, we adopt a different perspective and place the focus on experience of hub building from other international commodities. We analyse three commodities - crude oil, iron ore and coal, and draw experience on the role of governance in development of hub based prices. In particular, we propose that the role of governance is different at different stages of the pricing transition to market based pricing. Governance could play an important role at the initial stage, building the relevant soft and physical infrastructure which facilitates the reaping of first mover advantage. As the market develops, private sector players may prefer less involvement of governance, which may distort markets. With market stabilization, governance should be focused on maintaining stable rules and regulation for private sector development, as well as monitoring for further changes in global trends. To facilitate the building of a benchmark price, the public sector should adopt a long-term and overarching view on industry growth.

  20. Excitatory Neuronal Hubs Configure Multisensory Integration of Slow Waves in Association Cortex

    Directory of Open Access Journals (Sweden)

    Satoshi Kuroki

    2018-03-01

    Full Text Available Summary: Multisensory integration (MSI is a fundamental emergent property of the mammalian brain. During MSI, perceptual information encoded in patterned activity is processed in multimodal association cortex. The systems-level neuronal dynamics that coordinate MSI, however, are unknown. Here, we demonstrate intrinsic hub-like network activity in the association cortex that regulates MSI. We engineered calcium reporter mouse lines based on the fluorescence resonance energy transfer sensor yellow cameleon (YC2.60 expressed in excitatory or inhibitory neurons. In medial and parietal association cortex, we observed spontaneous slow waves that self-organized into hubs defined by long-range excitatory and local inhibitory circuits. Unlike directional source/sink-like flows in sensory areas, medial/parietal excitatory and inhibitory hubs had net-zero balanced inputs. Remarkably, multisensory stimulation triggered rapid phase-locking mainly of excitatory hub activity persisting for seconds after the stimulus offset. Therefore, association cortex tends to form balanced excitatory networks that configure slow-wave phase-locking for MSI. Video Abstract: : Kuroki et al. performed cell-type-specific, wide-field FRET-based calcium imaging to visualize cortical network activity induced by multisensory inputs. They observed phase-locking of cortical slow waves in excitatory neuronal hubs in association cortical areas that may underlie multisensory integration. Keywords: wide-field calcium imaging, multisensory integration, cortical slow waves, association cortex, phase locking, fluorescence resonance energy transfer, spontaneous activity, excitatory neuron, inhibitory neuron, mouse

  1. Extraversion modulates functional connectivity hubs of resting-state brain networks.

    Science.gov (United States)

    Pang, Yajing; Cui, Qian; Duan, Xujun; Chen, Heng; Zeng, Ling; Zhang, Zhiqiang; Lu, Guangming; Chen, Huafu

    2017-09-01

    Personality dimension extraversion describes individual differences in social behaviour and socio-emotional functioning. The intrinsic functional connectivity patterns of the brain are reportedly associated with extraversion. However, whether or not extraversion is associated with functional hubs warrants clarification. Functional hubs are involved in the rapid integration of neural processing, and their dysfunction contributes to the development of neuropsychiatric disorders. In this study, we employed the functional connectivity density (FCD) method for the first time to distinguish the energy-efficient hubs associated with extraversion. The resting-state functional magnetic resonance imaging data of 71 healthy subjects were used in the analysis. Short-range FCD was positively correlated with extraversion in the left cuneus, revealing a link between the local functional activity of this region and extraversion in risk-taking. Long-range FCD was negatively correlated with extraversion in the right superior frontal gyrus and the inferior frontal gyrus. Seed-based resting-state functional connectivity (RSFC) analyses revealed that a decreased long-range FCD in individuals with high extraversion scores showed a low long-range functional connectivity pattern between the medial and dorsolateral prefrontal cortex, middle temporal gyrus, and anterior cingulate cortex. This result suggests that decreased RSFC patterns are responsible for self-esteem, self-evaluation, and inhibitory behaviour system that account for the modulation and shaping of extraversion. Overall, our results emphasize specific brain hubs, and reveal long-range functional connections in relation to extraversion, thereby providing a neurobiological basis of extraversion. © 2015 The British Psychological Society.

  2. PERSEUS-HUB: Interactive and Collective Exploration of Large-Scale Graphs

    Directory of Open Access Journals (Sweden)

    Di Jin

    2017-07-01

    Full Text Available Graphs emerge naturally in many domains, such as social science, neuroscience, transportation engineering, and more. In many cases, such graphs have millions or billions of nodes and edges, and their sizes increase daily at a fast pace. How can researchers from various domains explore large graphs interactively and efficiently to find out what is ‘important’? How can multiple researchers explore a new graph dataset collectively and “help” each other with their findings? In this article, we present Perseus-Hub, a large-scale graph mining tool that computes a set of graph properties in a distributed manner, performs ensemble, multi-view anomaly detection to highlight regions that are worth investigating, and provides users with uncluttered visualization and easy interaction with complex graph statistics. Perseus-Hub uses a Spark cluster to calculate various statistics of large-scale graphs efficiently, and aggregates the results in a summary on the master node to support interactive user exploration. In Perseus-Hub, the visualized distributions of graph statistics provide preliminary analysis to understand a graph. To perform a deeper analysis, users with little prior knowledge can leverage patterns (e.g., spikes in the power-law degree distribution marked by other users or experts. Moreover, Perseus-Hub guides users to regions of interest by highlighting anomalous nodes and helps users establish a more comprehensive understanding about the graph at hand. We demonstrate our system through the case study on real, large-scale networks.

  3. Deuterium depth profiling in JT-60U W-shaped divertor tiles by nuclear reaction analysis

    International Nuclear Information System (INIS)

    Hayashi, T.; Ochiai, K.; Masaki, K.; Gotoh, Y.; Kutsukake, C.; Arai, T.; Nishitani, T.; Miya, N.

    2006-01-01

    Deuterium concentrations and depth profiles in plasma-facing graphite tiles used in the divertor of JAERI Tokamak-60 Upgrade (JT-60U) were investigated by nuclear reaction analysis (NRA). The highest deuterium concentration of D/ 12 C of 0.053 was found in the outer dome wing tile, where the deuterium accumulated probably through the deuterium-carbon co-deposition. In the outer and inner divertor target tiles, the D/ 12 C data were lower than 0.006. Additionally, the maximum (H + D)/ 12 C in the dome top tile was estimated to be 0.023 from the results of NRA and secondary ion mass spectroscopy (SIMS). Orbit following Monte-Carlo (OFMC) simulation showed energetic deuterons caused by neutral beam injections (NBI) were implanted into the dome region with high heat flux. Furthermore, the surface temperature and conditions such as deposition and erosion significantly influenced the accumulation process of deuterium. The deuterium depth profile, scanning electron microscope (SEM) observation and OFMC simulation indicated the deuterium was considered to accumulate through three processes: the deuterium-carbon co-deposition, the implantation of energetic deuterons and the deuterium diffusion into the bulk

  4. Development of the centrifugal pellet injector for JT-60U

    International Nuclear Information System (INIS)

    Kizu, Kaname; Hiratsuka, Hajime; Ichige, Hisashi

    2001-03-01

    For core fueling of JT-60U plasmas, a repetitive pellet injector which centrifugally accelerates D 2 cubic pellets using a straight rod has been developed. This centrifugal pellet injector can eject trains of up to 40 cubic pellets at frequencies of 1-10 Hz and velocities of 0.3-1.0 km/s. The average pellet mass is 3.6x10 20 atoms/pellet below 0.7 m/s. Key techniques for the development were a mesh structured acceleration component for removing gas sublimated from the pellet and a funnel with an appropriate angle connected just behind the acceleration chamber for introducing the pellet to plasma without destruction. Using the mesh structured components, the horizontal angular distribution of pellets ejected became narrow, because irregular pellet motion caused by sublimated gas was reduced. To investigate the performance of the injector, pellet injection experiments from the low magnetic field side (LFS) were conducted using ohmic heating plasmas. Central fueling and enhanced fueling rate have been observed. Dα intensity around the divertor region was reduced in a pellet injection plasma compared to gas puffing, indicating low recycling rate was maintained with the pellet injection. (author)

  5. The evolution of the MasAgro hubs

    NARCIS (Netherlands)

    Camacho-Villa, Tania Carolina; Almekinders, Conny; Hellin, Jon; Martinez-Cruz, Tania Eulalia; Rendon-Medel, Roberto; Guevara-Hernández, Francisco; Beuchelt, Tina D.; Govaerts, Bram

    2016-01-01

    Purpose: Little is known about effective ways to operationalize agricultural innovation processes. We use the MasAgro program in Mexico (which aims to increase maize and wheat productivity, profitability and sustainability), and the experiences of middle level ‘hub managers’, to understand how

  6. Magnetic field measurements of JT-60SA CS model coil

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Chikaraishi, Hirotaka; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Murakami, Haruyuki; Natsume, Kyohei; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2015-01-15

    Highlights: • Magnetic fields of the JT-60SA CS model coil were measured. • While the coil current was held constant at 20 kA, magnetic fields varied slightly with several different long time constants. • We investigated coils consisting of CIC conductors and having long time constants. - Abstract: In a cold test of the JT-60SA CS model coil, which has a quad-pancake configuration consisting of a Nb{sub 3}Sn cable-in-conduit (CIC) conductor, magnetic fields were measured using Hall sensors. For a holding coil current of 20 kA, measured magnetic fields varied slightly with long time constants in the range 17–571 s, which was much longer than the time constant derived from a measurement using a short straight sample. To validate the measurements, the magnetic fields of the model coil were calculated using a computational model representing the positions of Nb{sub 3}Sn strands inside the CIC conductor. The calculated results were in good agreement with the measurements. Consequently, the validity of the magnetic field measurements was confirmed. Next, we investigated other coils consisting of CIC conductors and having long time constants. The only commonality among the coils was the use of CIC conductors. At present, there is no obvious way to prevent generation of such magnetic-field variations with long time constants.

  7. New gauged N = 8, D = 4 supergravities

    International Nuclear Information System (INIS)

    Hull, C M

    2003-01-01

    New gaugings of four-dimensional N = 8 supergravity are constructed, including one which has a Minkowski space vacuum that preserves N = 2 supersymmetry and in which the gauge group is broken to SU(3) x U(1) 2 . Previous gaugings used the form of the ungauged action which is invariant under a rigid SL (8,R) symmetry and promoted a 28-dimensional subgroup (SO(8), SO(p, 8 - p) or the non-semi-simple contraction CSO(p, q, 8 - p - q)) to a local gauge group. Here, a dual form of the ungauged action is used which is invariant under SU*(8) instead of SL (8,R) and new theories are obtained by gauging 28-dimensional subgroups of SU*(8). The gauge groups are non-semi-simple and are different real forms of the CSO(2p, 8 - 2p) groups, denoted as CSO*(2p, 8 - 2p), and the new theories have a rigid SU(2) symmetry. The five-dimensional gauged N = 8 supergravities are dimensionally reduced to D = 4. The D = 5, SO(p, 6 - p) gauge theories reduce, after a duality transformation, to the D = 4, CSO(p, 6 - p, 2) gauging while the SO*(6) gauge theory reduces to the D = 4, CSO*(6, 2) gauge theory. The new theories are related to the old ones via an analytic continuation. The non-semi-simple gaugings can be dualized to forms with different gauge groups

  8. 76 FR 10328 - Grant of Authority for Subzone Status; Vestas Nacelles America, Inc. (Wind Turbine Nacelles, Hubs...

    Science.gov (United States)

    2011-02-24

    ... Status; Vestas Nacelles America, Inc. (Wind Turbine Nacelles, Hubs, Blades and Towers), Brighton, Denver...-purpose subzone at the wind turbine nacelle, hub, blade and tower manufacturing and warehousing facilities... status for activity related to the manufacturing and warehousing of wind turbine nacelles, hubs, blades...

  9. 78 FR 20314 - Jefferson Island Storage & Hub, L.L.C.; Notice of Filing

    Science.gov (United States)

    2013-04-04

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR13-44-000] Jefferson Island Storage & Hub, L.L.C.; Notice of Filing Take notice that on March 28, 2013, Jefferson Island Storage & Hub, L.L.C. filed to revise its Statement of Operating Conditions to among others, update...

  10. When Is Hub Gene Selection Better than Standard Meta-Analysis?

    Science.gov (United States)

    Langfelder, Peter; Mischel, Paul S.; Horvath, Steve

    2013-01-01

    Since hub nodes have been found to play important roles in many networks, highly connected hub genes are expected to play an important role in biology as well. However, the empirical evidence remains ambiguous. An open question is whether (or when) hub gene selection leads to more meaningful gene lists than a standard statistical analysis based on significance testing when analyzing genomic data sets (e.g., gene expression or DNA methylation data). Here we address this question for the special case when multiple genomic data sets are available. This is of great practical importance since for many research questions multiple data sets are publicly available. In this case, the data analyst can decide between a standard statistical approach (e.g., based on meta-analysis) and a co-expression network analysis approach that selects intramodular hubs in consensus modules. We assess the performance of these two types of approaches according to two criteria. The first criterion evaluates the biological insights gained and is relevant in basic research. The second criterion evaluates the validation success (reproducibility) in independent data sets and often applies in clinical diagnostic or prognostic applications. We compare meta-analysis with consensus network analysis based on weighted correlation network analysis (WGCNA) in three comprehensive and unbiased empirical studies: (1) Finding genes predictive of lung cancer survival, (2) finding methylation markers related to age, and (3) finding mouse genes related to total cholesterol. The results demonstrate that intramodular hub gene status with respect to consensus modules is more useful than a meta-analysis p-value when identifying biologically meaningful gene lists (reflecting criterion 1). However, standard meta-analysis methods perform as good as (if not better than) a consensus network approach in terms of validation success (criterion 2). The article also reports a comparison of meta-analysis techniques applied to

  11. When is hub gene selection better than standard meta-analysis?

    Directory of Open Access Journals (Sweden)

    Peter Langfelder

    Full Text Available Since hub nodes have been found to play important roles in many networks, highly connected hub genes are expected to play an important role in biology as well. However, the empirical evidence remains ambiguous. An open question is whether (or when hub gene selection leads to more meaningful gene lists than a standard statistical analysis based on significance testing when analyzing genomic data sets (e.g., gene expression or DNA methylation data. Here we address this question for the special case when multiple genomic data sets are available. This is of great practical importance since for many research questions multiple data sets are publicly available. In this case, the data analyst can decide between a standard statistical approach (e.g., based on meta-analysis and a co-expression network analysis approach that selects intramodular hubs in consensus modules. We assess the performance of these two types of approaches according to two criteria. The first criterion evaluates the biological insights gained and is relevant in basic research. The second criterion evaluates the validation success (reproducibility in independent data sets and often applies in clinical diagnostic or prognostic applications. We compare meta-analysis with consensus network analysis based on weighted correlation network analysis (WGCNA in three comprehensive and unbiased empirical studies: (1 Finding genes predictive of lung cancer survival, (2 finding methylation markers related to age, and (3 finding mouse genes related to total cholesterol. The results demonstrate that intramodular hub gene status with respect to consensus modules is more useful than a meta-analysis p-value when identifying biologically meaningful gene lists (reflecting criterion 1. However, standard meta-analysis methods perform as good as (if not better than a consensus network approach in terms of validation success (criterion 2. The article also reports a comparison of meta-analysis techniques

  12. When is hub gene selection better than standard meta-analysis?

    Science.gov (United States)

    Langfelder, Peter; Mischel, Paul S; Horvath, Steve

    2013-01-01

    Since hub nodes have been found to play important roles in many networks, highly connected hub genes are expected to play an important role in biology as well. However, the empirical evidence remains ambiguous. An open question is whether (or when) hub gene selection leads to more meaningful gene lists than a standard statistical analysis based on significance testing when analyzing genomic data sets (e.g., gene expression or DNA methylation data). Here we address this question for the special case when multiple genomic data sets are available. This is of great practical importance since for many research questions multiple data sets are publicly available. In this case, the data analyst can decide between a standard statistical approach (e.g., based on meta-analysis) and a co-expression network analysis approach that selects intramodular hubs in consensus modules. We assess the performance of these two types of approaches according to two criteria. The first criterion evaluates the biological insights gained and is relevant in basic research. The second criterion evaluates the validation success (reproducibility) in independent data sets and often applies in clinical diagnostic or prognostic applications. We compare meta-analysis with consensus network analysis based on weighted correlation network analysis (WGCNA) in three comprehensive and unbiased empirical studies: (1) Finding genes predictive of lung cancer survival, (2) finding methylation markers related to age, and (3) finding mouse genes related to total cholesterol. The results demonstrate that intramodular hub gene status with respect to consensus modules is more useful than a meta-analysis p-value when identifying biologically meaningful gene lists (reflecting criterion 1). However, standard meta-analysis methods perform as good as (if not better than) a consensus network approach in terms of validation success (criterion 2). The article also reports a comparison of meta-analysis techniques applied to

  13. The East African Resilience Innovation Hub | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Project leadership The Resilience Innovation Hub will be housed within a ... Region at the Levy Mwanawasa Regional Centre, Lusaka -Conflict Early Warning and ... Authority on Development, Addis Ababa This initiative will support innovative ...

  14. Prostate cancer risk locus at 8q24 as a regulatory hub by physical interactions with multiple genomic loci across the genome.

    Science.gov (United States)

    Du, Meijun; Yuan, Tiezheng; Schilter, Kala F; Dittmar, Rachel L; Mackinnon, Alexander; Huang, Xiaoyi; Tschannen, Michael; Worthey, Elizabeth; Jacob, Howard; Xia, Shu; Gao, Jianzhong; Tillmans, Lori; Lu, Yan; Liu, Pengyuan; Thibodeau, Stephen N; Wang, Liang

    2015-01-01

    Chromosome 8q24 locus contains regulatory variants that modulate genetic risk to various cancers including prostate cancer (PC). However, the biological mechanism underlying this regulation is not well understood. Here, we developed a chromosome conformation capture (3C)-based multi-target sequencing technology and systematically examined three PC risk regions at the 8q24 locus and their potential regulatory targets across human genome in six cell lines. We observed frequent physical contacts of this risk locus with multiple genomic regions, in particular, inter-chromosomal interaction with CD96 at 3q13 and intra-chromosomal interaction with MYC at 8q24. We identified at least five interaction hot spots within the predicted functional regulatory elements at the 8q24 risk locus. We also found intra-chromosomal interaction genes PVT1, FAM84B and GSDMC and inter-chromosomal interaction gene CXorf36 in most of the six cell lines. Other gene regions appeared to be cell line-specific, such as RRP12 in LNCaP, USP14 in DU-145 and SMIN3 in lymphoblastoid cell line. We further found that the 8q24 functional domains more likely interacted with genomic regions containing genes enriched in critical pathways such as Wnt signaling and promoter motifs such as E2F1 and TCF3. This result suggests that the risk locus may function as a regulatory hub by physical interactions with multiple genes important for prostate carcinogenesis. Further understanding genetic effect and biological mechanism of these chromatin interactions will shed light on the newly discovered regulatory role of the risk locus in PC etiology and progression. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  15. Virtual Hubs for facilitating access to Open Data

    Science.gov (United States)

    Mazzetti, Paolo; Latre, Miguel Á.; Ernst, Julia; Brumana, Raffaella; Brauman, Stefan; Nativi, Stefano

    2015-04-01

    In October 2014 the ENERGIC-OD (European NEtwork for Redistributing Geospatial Information to user Communities - Open Data) project, funded by the European Union under the Competitiveness and Innovation framework Programme (CIP), has started. In response to the EU call, the general objective of the project is to "facilitate the use of open (freely available) geographic data from different sources for the creation of innovative applications and services through the creation of Virtual Hubs". In ENERGIC-OD, Virtual Hubs are conceived as information systems supporting the full life cycle of Open Data: publishing, discovery and access. They facilitate the use of Open Data by lowering and possibly removing the main barriers which hampers geo-information (GI) usage by end-users and application developers. Data and data services heterogeneity is recognized as one of the major barriers to Open Data (re-)use. It imposes end-users and developers to spend a lot of effort in accessing different infrastructures and harmonizing datasets. Such heterogeneity cannot be completely removed through the adoption of standard specifications for service interfaces, metadata and data models, since different infrastructures adopt different standards to answer to specific challenges and to address specific use-cases. Thus, beyond a certain extent, heterogeneity is irreducible especially in interdisciplinary contexts. ENERGIC-OD Virtual Hubs address heterogeneity adopting a mediation and brokering approach: specific components (brokers) are dedicated to harmonize service interfaces, metadata and data models, enabling seamless discovery and access to heterogeneous infrastructures and datasets. As an innovation project, ENERGIC-OD will integrate several existing technologies to implement Virtual Hubs as single points of access to geospatial datasets provided by new or existing platforms and infrastructures, including INSPIRE-compliant systems and Copernicus services. ENERGIC OD will deploy a

  16. Emerging Education Hubs: The Case of Singapore

    Science.gov (United States)

    Sidhu, Ravinder; Ho, K.-C.; Yeoh, Brenda

    2011-01-01

    In anticipation of a globalising post-Fordist political economy, countries and universities are increasingly pursuing strategic transnational education and research alliances. This article analyses the Global Schoolhouse, a key education policy platform that aims to transform Singapore into a knowledge and innovation hub by establishing networks…

  17. Validation of special processes for the integration activities of the JT-60SA TF coils manufactured in Italy

    Energy Technology Data Exchange (ETDEWEB)

    Polli, Gian Mario, E-mail: gianmario.polli@enea.it [ENEA, UT-FUS, Via E. Fermi 45, Frascati (Italy); Cucchiaro, Antonio; Cocilovo, Valter [ENEA, UT-FUS, Via E. Fermi 45, Frascati (Italy); Drago, Giovanni; Pesenti, Paolo; Cuneo, Stefano; Terzi, Franco [ASG Superconductors, Corso Perrone 73 r, Genova (Italy); Phillips, Guy; Tomarchio, Valerio [JT-60SA European Home Team, 85748 Garching bei Munchen (Germany)

    2015-10-15

    Highlights: • Insertion. • Casing welding. • Casing embedding. - Abstract: In the framework of the Broader Approach Agreement for the construction of the JT-60SA tokamak, ENEA provides 9 of the 18 toroidal field (TF) coils of the JT-60SA magnet system. The 9 coils are being manufactured by ASG superconductors in Genoa under the supervision of ENEA in collaboration with the JT-60SA European home team. The manufacturing is composed of two main steps: one concerning winding pack assembly and impregnation, and the other devoted to the integration into the casing structure and associated final coil preparation. This paper describes the results of the validation activities set-up for the integration phase. Specifically, welding of casing components has been retained particularly critical for at least three reasons: (i) during welding the WP may be damaged by the intense heating; (ii) distortion caused by heating may determine incorrect coil geometry and then field errors; and (iii) flaws may reduce structural strength and then the overall lifetime of the machine. Similarly, final embedding has been demonstrated on a 1 m long mock-up of the coil. Main results and lessons learned are here described.

  18. A coil test facility for the cryogenic tests of the JT-60SA TF coils

    International Nuclear Information System (INIS)

    Chantant, M.; Genini, L.; Bayetti, P.; Millet, F.; Wanner, M.; Massaut, V.; Corte, A. Della; Ardelier-Desage, F.; Catherine-Dumont, V.; Dael, A.; Decool, P.; Donati, A.; Duchateau, J.L.; Garibaldi, P.; Girard, S.; Hatchressian, J.C.; Fejoz, P.; Jamotton, P.; Jourdheuil, L.; Juster, F.P.

    2011-01-01

    In the framework of the Broader Approach Activities, the EU will deliver to Japan the 18 superconducting coils, which constitute the JT-60SA Toroidal field magnet. These 18 coils, manufactured by France and Italy, will be cold tested before shipping to Japan. For this purpose, the European Joint Undertaking for ITER, the Development of Fusion Energy ('Fusion for Energy', F4E) and the European Voluntary Contributors are collaborating to design and set-up a coil test facility (CTF) and to perform the acceptance test of the 18 JT-60SA Toroidal Field (TF) coils. The test facility is designed to test one coil at a time at nominal current and cryogenic temperature. The test of the first coil of each manufacturer includes a quench triggered by increasing the temperature. The project is presently in the detailed design phase.

  19. Waves, currents and sediment transport modelling at the Wave Hub site

    OpenAIRE

    Gonzalez-Santamaria, Raul

    2013-01-01

    Primary supervisory team: Qingping Zou and Shunqi Pan This research project uses an integrated modelling system to investigate the effects of a wave farm on nearshore sediment transport at the Wave Hub site. The Wave Hub project is a large scale demonstration site for the development of the operation of arrays of wave energy generation devices located at the southwest coast of the UK where multiple field measurements took place. Particular attention of this study was paid to th...

  20. 3D Printing of Materials with Tunable Failure via Bioinspired Mechanical Gradients.

    Science.gov (United States)

    Kokkinis, Dimitri; Bouville, Florian; Studart, André R

    2018-05-01

    Mechanical gradients are useful to reduce strain mismatches in heterogeneous materials and thus prevent premature failure of devices in a wide range of applications. While complex graded designs are a hallmark of biological materials, gradients in manmade materials are often limited to 1D profiles due to the lack of adequate fabrication tools. Here, a multimaterial 3D-printing platform is developed to fabricate elastomer gradients spanning three orders of magnitude in elastic modulus and used to investigate the role of various bioinspired gradient designs on the local and global mechanical behavior of synthetic materials. The digital image correlation data and finite element modeling indicate that gradients can be effectively used to manipulate the stress state and thus circumvent the weakening effect of defect-rich interfaces or program the failure behavior of heterogeneous materials. Implementing this concept in materials with bioinspired designs can potentially lead to defect-tolerant structures and to materials whose tunable failure facilitates repair of biomedical implants, stretchable electronics, or soft robotics. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. J.T. van der Kemp and his Critique of the Settler Farmers on the ...

    African Journals Online (AJOL)

    Theoretically, I draw on some insights from works of Michel Foucault, especially with regard to eighteenth and early nineteenth century 'representational thought', where 'idea' and 'object' are directly related. Keywords: J.T. van der Kemp, settler farmers, frontier, patriot, rebellion, slavery, baptism, cruelty, Black Circuit Court ...

  2. Joint resistance measurements of pancake and terminal joints for JT-60SA EF coils

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Murakami, Haruyuki; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2013-11-15

    Highlights: • To evaluate the joint fabrication technology for the JT-60SA EF coils, joint resistance measurements were conducted with a joint sample. • The joint sample was composed of pancake and terminal joints. • The measurements demonstrated that both joints fulfilled the design requirement. • Considering the measurements, the characteristics of both joints were investigated using an analytical model that represents the joints. -- Abstract: To evaluate the joint fabrication technology for the JT-60SA EF coils, joint resistance measurements were conducted using a sample consisting of pancake and terminal joints. Both joints are shake-hands lap joints composed of cable-in-conduit conductors and a pure copper saddle-shaped spacer. The measurements demonstrated that both joints fulfilled the design requirement. Considering these measurements, the characteristics of both joints were investigated using analytical models that represent the joints. The analyses indicated that the characteristics of the conductors used in the joints affect the characteristics of the joints.

  3. Design and performance tests of gas circulation heating of JT-60U vacuum vessel

    International Nuclear Information System (INIS)

    Yotsuga, M.; Masuzaki, T.; Sago, H.; Nishikane, M.; Uchikawa, T.; Iritani, Y.; Murakami, T.; Horiike, H.; Neyatani, Y.; Ninomiya, H.; Matsukawa, M.; Ando, T.; Miyachi, I.

    1992-01-01

    This paper reports that in the final stage of construction of the upgraded JT-60 device (JT-60U), baking tests of the vacuum vessel was performed. The vessel torus was heated-up to 300 degrees C by means of the nitrogen gas circulation system and electric heaters mounted on the outboard solid wall of the vessel. The design of the gas flow channels inside the double-wall structure of the vessel was done based on flow model tests, fluid analysis, and flow network analysis. The results of the baking tests were satisfactory. In maintaining 300 degrees C bake-out temperature, required heating power of the gas circulation system and outboard heaters was 520kW and 50kW, respectively. The temperature distribution over the vessel wall was within 300 ± 30 degrees C. It was also shown or suggested that heat-up and cool-down time is about 30 hours. The baking tests data have been reflected on operations for plasma experiments

  4. Fabrication and performance tests of a prototype in-situ coating machine for JT-60

    International Nuclear Information System (INIS)

    Obara, Kenjiro; Abe, Tetsuya; Murakami, Yoshio

    1987-09-01

    Prior to the design and construction of the JT-60's in-situ coating device, a prototype machine was fabricated and tested to confirm the applicability of proposed driving methods and mechanical elements to the device which would be operated in very severe conditions including high ambient temperature and high vacuum. The machine basically consists of an in-vessel manipulator, a fiberscope and an ohmically heated titanium evaporator. From the test results, we recommended to use the combination of Inconel 625 and a self-lubricating alloy for the solid-lubricated bearings and MoS 2 -coated Inconel 625 for the solid-lubricated gears. It was also found that TiC coating showed a effect for the prevention of welding between bolts and nuts. In order to optimize the operating parameters of the machine, many wall inspection tests and titanium evaporation tests were carried out in a large vacuum vessel by simulating the JT-60 conditions. (author)

  5. Hubs and spokes in Regional Trade Agreements

    NARCIS (Netherlands)

    Vaal, A. de

    2017-01-01

    In the plethora of Regional Trade Agreements (RTAs) some countries are involved in much more RTAs than others. Furthermore, some countries take in a position as a hub: they have trade agreements with many other countries, while their partner countries are much less involved in RTA relations. Even

  6. Improvement of the real-time processor in JT-60 data processing system

    International Nuclear Information System (INIS)

    Sakata, S.; Kiyono, K.; Sato, M.; Kominato, T.; Sueoka, M.; Hosoyama, H.; Kawamata, Y.

    2009-01-01

    Real-time processor, RTP is a basic subsystem in the JT-60 data processing system and plays an important role in JT-60 feedback control for plasma experiment. During the experiment, RTP acquires various diagnostic signals, processes them into a form of physical values, and transfers them as sensor signals to the particle supply and heating control supervisor for feedback control via reflective memory synchronization with 1 ms clock signals. After the start of RTP operation in 1997, to meet the demand for advanced plasma experiment, RTP had been improved continuously such as by addition of diagnostic signals with faster digitizers, reducing time for data transfer utilizing reflective memory instead of CAMAC. However, it is becoming increasingly difficult to maintain, manage, and improve the outdated RTP with limited system CPU capability. Currently, a prototype RTP system is being developed for the next real-time processing system, which is composed of clustered system utilizing VxWorks computer. The processes on the existing RTP system will be decentralized to the VxWorks computer to solve the issues of the existing RTP system. The prototype RTP system will start to operate in August 2008.

  7. Characteristics of divertor plasma and scrape-off layer in JT-60U

    International Nuclear Information System (INIS)

    Itami, K.; Shimada, M.; Hosogane, N.

    1992-01-01

    Heat flux to the divertor is measured by thermography and the heat transport in the scrape-off layer is studied in beam heated discharges of JT-60U. The heat flux onto the divertor is ∝50% of total beam power at maximum. The in-out asymmetry of the heat flux P HEAT in /P HEAT out is as large as 20-40% when the ion grad-B drift is toward the divertor. Differences in P HEAT in /P HEA T out due to the direction of ion grad-B drift are as large as large as ∝40%. A scaling of the peaking factor Y of heat flux, defined by Y=2πRfq max /P HEAT , is obtained for beam heated discharges in JT-60U with a wide range of plasma parameters. The Y corresponds to the inverse of the thickness of the scrape-off layer. From a statistical analysis, it is found that the peaking factor Y of heat flux scales as P HEAT 0.49±0.18 anti n e -0.45±0.22 q eff -0.67±0.18 . (orig.)

  8. Developmental prototype for replacement of JT-60 timing system

    International Nuclear Information System (INIS)

    Akasaka, H.; Kawamata, Y.; Yonekawa, I.

    2004-01-01

    The present CAMAC based timing system has been used for synchronizing sequential events of the discharge and the data collection of the interesting JT-60U experiment plasma phenomena. However, a more flexible and sophisticated state-of-the-art timing system now is required to realize advanced plasma control with minimal maintenance costs. In this context, the versa module Europe (VME-bus) system with a high-speed data communication network using reflective memory (RM) modules and user-friendly application software based on MATLAB TM tools has been selected to develop the new prototype timing system. In the ZENKEI, the supervisory control system of the JT-60, the supervisory timing system provides the 50-μs master clock pulses, the various timing signal preparation logic, which is built into the digital signal processing (DSP) module in conjunction with the discharge sequence event signals, and the 6.2 MB/s high-speed communication data link provided by the RM module. Except the clock pulse generator (CPG) module, no other special timing module is necessary for this new timing system. The timing signal is prepared by software logic in conjunction with sequential events and the preset timer, is transferred to the subsystems through the RM module, where it is synchronized to the 50-μs clock pulses. The timing system of the subsystems also consists of hardware similar in structure to the ZENKEI timing system. The fundamental timing system configuration, the necessary functions, and the preliminary test results of the prototype system are reported in this presentation

  9. Feedback control of plasma configuration in JT-60

    International Nuclear Information System (INIS)

    Ninomiya, Hiromasa; Kikuchi, Mitsuru; Yoshino, Ryuji; Hosogane, Nobuyuki; Kimura, Toyoaki; Kurihara, Kenichi; Takahashi, Minoru; Hayashi, Kazuo.

    1986-08-01

    Plasma current, plasma position (center of the outermost magnetic surface), decay index n index and width of the divertor throat are feedback controlled by using 5 kinds of poloidal field coils in JT-60. 5 control commands are calculated in a feedback control computer in each 1 msec. These feedback control functions are checked in ohmically heated plasma. The control characteristics of the plasma are well understood by the simplified control analysis and are consistent with the precise matrix transfer function analysis in the frequency domain and the simulation analysis which include the effects of eddy currents, delay time elements and mutual interactions between controllers. The usefulness of these analyses is experimentally confirmed. Each controlled variable is well feedback controlled to the command and the experimentally realized equilibrium configuration is checked by the well calibrated magnetic probes. Fast boundary identification code is used for the identification of the equilibrium and results are consistent with the precalculated plasma equilibria. By using this feedback control system of the plasma configuration and the equilibrium identification method, we have obtained the stable limiter and divertor configuration. The maximum parameters obtained during OH(I) experimental period are plasma current I p = 1.8 MA, the effective safety factor q eff e = 5.7 x 10 19 m -3 (Murakami parameter of 4.5) and the pulse length of 5 ∼ 10 sec. (author)

  10. ERATO-code analysis of vacuum magnetic field oscillations in JT-60 divertor configuration

    International Nuclear Information System (INIS)

    Ozeki, Takahisa; Tokuda, Shinji; Tsunematsu, Toshihide; Ishida, Shinichi; Neyatani, Yuzuru; Itami, Kiyoshi; Azumi, Masafumi

    1989-07-01

    Magnetic field oscillations caused by external kink instabilities are numerically studied by using the ideal MHD stability code ERATO-J. Dependence of a spatial distribution of their amplitude and phase on aspect-ratio, beta-poloidal, shaping of conducting shell and divertor/limiter configurations is examined in detail. In the low aspect ratio plasma, the amplitude of magnetic oscillations in the inner side of the torus is larger than that in the outer. On the contrary, as the poloidal beta increases, the amplitude in the outer side of the torus becomes larger than that in the inner. In the divertor configuration, the amplitude of oscillations reduces near the X-point and the phase is locally modulated. The coherent magnetic oscillations observed in JT-60 agree well with the theoretical results, where the vacuum vessel is assumed to be an ideal conducting shell. The non-uniformity of the poloidal distribution observed in JT-60 can be explained by the combined effects of the finite beta, the X-point and the shape of shell. (author)

  11. Dynamic simulations for preparing the acceptance test of JT-60SA cryogenic system

    Science.gov (United States)

    Cirillo, R.; Hoa, C.; Michel, F.; Poncet, J. M.; Rousset, B.

    2016-12-01

    Power generation in the future could be provided by thermo-nuclear fusion reactors like tokamaks. There inside, the fusion reaction takes place thanks to the generation of plasmas at hundreds of millions of degrees that must be confined magnetically with superconductive coils, cooled down to around 4.5 K. Within this frame, an experimental tokamak device, JT-60SA is currently under construction in Naka (Japan). The plasma works cyclically and the coil system is subject to pulsed heat loads. In order to size the refrigerator close to the average power and hence optimizing investment and operational costs, measures have to be taken to smooth the heat load. Here we present a dynamic model of the JT-60SA's Auxiliary Cold box (ACB) for preparing the acceptance tests of the refrigeration system planned in 2016 in Naka. The aim of this study is to simulate the pulsed load scenarios using different process controls. All the simulations have been performed with EcosimPro® and the associated cryogenic library: CRYOLIB.

  12. Controls on shallow landslide initiation: Diverse hydrologic pathways, 3D failure geometries, and unsaturated soil suctions

    Science.gov (United States)

    Reid, Mark; Iverson, Richard; Brien, Dianne; Iverson, Neal; LaHusen, Richard; Logan, Matthew

    2017-04-01

    Shallow landslides and ensuing debris flows are a common hazard worldwide, yet forecasting their initiation at a specific site is challenging. These challenges arise, in part, from diverse near-surface hydrologic pathways under different wetting conditions, 3D failure geometries, and the effects of suction in partially saturated soils. Simplistic hydrologic models typically used for regional hazard assessment disregard these complexities. As an alterative to field studies where the effects of these governing factors can be difficult to isolate, we used the USGS debris-flow flume to conduct controlled, field-scale landslide initiation experiments. Using overhead sprinklers or groundwater injectors on the flume bed, we triggered failures using three different wetting conditions: groundwater inflow from below, prolonged moderate-intensity precipitation, and bursts of high-intensity precipitation. Failures occurred in 6 m3 (0.65-m thick and 2-m wide) prisms of loamy sand on a 31° slope; these field-scale failures enabled realistic incorporation of nonlinear scale-dependent effects such as soil suction. During the experiments, we monitored soil deformation, variably saturated pore pressures, and moisture changes using ˜50 sensors sampling at 20 Hz. From ancillary laboratory tests, we determined shear strength, saturated hydraulic conductivities, and unsaturated moisture retention characteristics. The three different wetting conditions noted above led to different hydrologic pathways and influenced instrumental responses and failure timing. During groundwater injection, pore-water pressures increased from the bed of the flume upwards into the sediment, whereas prolonged moderate infiltration wet the sediment from the ground surface downward. In both cases, pore pressures acting on the impending failure surface slowly rose until abrupt failure. In contrast, a burst of intense sprinkling caused rapid failure without precursory development of widespread positive pore

  13. Publishing and sharing of hydrologic models through WaterHUB

    Science.gov (United States)

    Merwade, V.; Ruddell, B. L.; Song, C.; Zhao, L.; Kim, J.; Assi, A.

    2011-12-01

    Most hydrologists use hydrologic models to simulate the hydrologic processes to understand hydrologic pathways and fluxes for research, decision making and engineering design. Once these tasks are complete including publication of results, the models generally are not published or made available to the public for further use and improvement. Although publication or sharing of models is not required for journal publications, sharing of models may open doors for new collaborations, and avoids duplication of efforts if other researchers are interested in simulating a particular watershed for which a model already exists. For researchers, who are interested in sharing models, there are limited avenues to publishing their models to the wider community. Towards filling this gap, a prototype cyberinfrastructure (CI), called WaterHUB, is developed for sharing hydrologic data and modeling tools in an interactive environment. To test the utility of WaterHUB for sharing hydrologic models, a system to publish and share SWAT (Soil Water Assessment Tool) is developed. Users can utilize WaterHUB to search and download existing SWAT models, and also upload new SWAT models. Metadata such as the name of the watershed, name of the person or agency who developed the model, simulation period, time step, and list of calibrated parameters also published with individual model.

  14. Mapping the changed hubs and corresponding functional connectivity in idiopathic restless legs syndrome.

    Science.gov (United States)

    Liu, Chunyan; Wang, Jiaojian; Hou, Yue; Qi, Zhigang; Wang, Li; Zhan, Shuqin; Wang, Rong; Wang, Yuping

    2018-05-01

    The hubs of the brain network play a key role in integrating and transferring information between different functional modules. However, whether the changed pattern in functional network hubs contributes to the onset of leg discomfort symptoms in restless legs syndrome (RLS) patients remains unclear. Using resting-state functional magnetic resonance imaging (rs-fMRI) and graph theory methods, we investigated whether alterations of hubs can be detected in RLS. First, we constructed the whole-brain voxelwise functional connectivity and calculated a functional connectivity strength (FCS) map in each of 16 drug-naive idiopathic RLS patients and 26 gender- and age-matched healthy control (HC) subjects. Next, a two-sample t test was applied to compare the FCS maps between HC and RLS patients, and to identify significant changes in FCS in RLS patients. To further elucidate the corresponding changes in the functional connectivity patterns of the aberrant hubs in RLS patients, whole-brain resting-state functional connectivity analyses for the hub areas were performed. The hub analysis revealed decreased FCS in the cuneus, fusiform gyrus, paracentral lobe, and precuneus, and increased FCS in the superior frontal gyrus and thalamus in idiopathic drug-naive RLS patients. Subsequent functional connectivity analyses revealed decreased functional connectivity in sensorimotor and visual processing networks and increased functional connectivity in the affective cognitive network and cerebellar-thalamic circuit. Furthermore, the mean FCS value in the superior frontal gyrus was significantly correlated with Hamilton Anxiety Rating Scale scores in RLS patients, and the mean FCS value in the fusiform gyrus was significantly correlated with Hamilton Depression Rating Scale scores. These findings may provide novel insight into the pathophysiology of RLS. Copyright © 2018 Elsevier B.V. All rights reserved.

  15. Altered network hub connectivity after acute LSD administration

    Directory of Open Access Journals (Sweden)

    Felix Müller

    Full Text Available LSD is an ambiguous substance, said to mimic psychosis and to improve mental health in people suffering from anxiety and depression. Little is known about the neuronal correlates of altered states of consciousness induced by this substance. Limited previous studies indicated profound changes in functional connectivity of resting state networks after the administration of LSD. The current investigation attempts to replicate and extend those findings in an independent sample. In a double-blind, randomized, cross-over study, 100 μg LSD and placebo were orally administered to 20 healthy participants. Resting state brain activity was assessed by functional magnetic resonance imaging. Within-network and between-network connectivity measures of ten established resting state networks were compared between drug conditions. Complementary analysis were conducted using resting state networks as sources in seed-to-voxel analyses. Acute LSD administration significantly decreased functional connectivity within visual, sensorimotor and auditory networks and the default mode network. While between-network connectivity was widely increased and all investigated networks were affected to some extent, seed-to-voxel analyses consistently indicated increased connectivity between networks and subcortical (thalamus, striatum and cortical (precuneus, anterior cingulate cortex hub structures. These latter observations are consistent with findings on the importance of hubs in psychopathological states, especially in psychosis, and could underlay therapeutic effects of hallucinogens as proposed by a recent model. Keywords: LSD, fMRI, Functional connectivity, Networks, Hubs

  16. Pinoy Nutrition Hub: The Philippine Experience in Addressing Moderate Malnutrition

    International Nuclear Information System (INIS)

    Ramos, Arlo; Fuentes, Eureka; Duque, Yvonette; Soriano, Nezer; Gomez, Marijo

    2014-01-01

    Full text: • Objective: Malnutrition is a persistent problem in the Philippines. The 2011 survey of the Food and Nutrition Research Institute reported that 3 out of 10 children are malnourished. Data shows 20.2% of children 0-47 months are underweight while 33.6% are stunted. This rate is higher in depressed areas in the country. PD Hearth is a time and tested effective program model to address malnutrition. But the PDH has minimum standards that need to be followed in the program implementation. However, a developing country like the Philippines has limitations in its resources and implementations. This paper aims to share the Philippine experience in addressing moderate malnutrition through a contextualized and modified PD Hearth approach. The specific objectives of this paper are: - to describe the challenges in implementing PD Hearth in the context of the Philippines; - to describe the innovations and modifications in the PD Hearth; - and, to illustrate the successful intervention of the PNH program against malnourished children in the community. • Methods: The Pinoy Nutrition Hub model is an innovation of PD Hearth approach. The first step was the participatory approach evaluation of existing programs on MNCHN in the communities. The next step was for the stakeholders to identify the gaps and address them. This was followed by gathering lessons learned and good practices that arose from implementing PD Hearth. Innovations were adopted to address restrictions and maximize learning in its implementation. The contextualized approach was called Pinoy Nutrition Hub (PNH). • Outcomes: - The PNH was piloted in three Area Development Programs (ADP) that represent the three island groups of the Philippines. All three ADPs reported improvement in the weight of the malnourished children enrolled in the program. Below is an illustration of the how the actual weight of children in the Visayas ADP increased. Figure 1 (Display Omitted). Average Weight of Malnourished

  17. A State Cyber Hub Operations Framework

    Science.gov (United States)

    2016-06-01

    current and future decision support. Finally, the Hub operations team must track and report key performance indictors ( KPIs ) (established by the state...Region); then mutually agreed-upon core KPIs should be identified and reported at this time. The goal of the Act Element is to implement the decision...Force Headquarters Page 58 JIE Joint Information Environment JMC JIE Management Construct KPI Key Performance Indicator LEA Law Enforcement

  18. Status of the cold test facility for the JT-60SA tokamak toroidal field coils

    Energy Technology Data Exchange (ETDEWEB)

    Abdel Maksoud, Walid, E-mail: walid.abdelmaksoud@cea.fr; Bargueden, Patrick; Bouty, André; Dispau, Gilles; Donati, André; Eppelle, Dominique; Genini, Laurent; Guiho, Patrice; Guihard, Quentin; Joubert, Jean-Michel; Kuster, Olivier; Médioni, Damien; Molinié, Frédéric; Sinanna, Armand; Solenne, Nicolas; Somson, Sébastien; Vieillard, Laurence

    2015-10-15

    Highlights: • The 5 K cryogenic loop includes a 500 W refrigerator and a She cold pump. • The coils are energized thanks to a 25.7 kA power supply and HTS current leads. • Temperature margin tests between 5 K and 7.5 K will be made on each coil. • A magnet safety system protects each double pancake of the coil in case of quench. • Instrumentation is monitored on a 1 Hz to 10 kHz fast acquisition system. - Abstract: JT-60SA is a fusion experiment which is jointly constructed by Japan and Europe and which shall contribute to the early realization of fusion energy, by providing support to the operation of ITER, and by addressing key physics issues for ITER and DEMO. In order to achieve these goals, the existing JT-60U experiment will be upgraded to JT-60SA by using superconducting coils. The 18 TF coils of the JT-60SA device will be provided by European industry and tested in a Cold Test Facility (CTF) at CEA Saclay. The coils will be tested at the nominal current of 25.7 kA and will be cooled with supercritical helium between 5 K and 7.5 K to check the temperature margin against a quench. The main objective of these tests is to check the TF coils performance and hence mitigate the fabrication risks. The most important components of the facility are: a 11.5 m × 6.5 m large cryostat in which the TF coils will be thermally insulated by vacuum; a 500 W helium refrigerator and a valve box to cool the coils down to 5 K and circulate 24 g/s of supercritical helium through the winding pack and through the casing; a power supply and HTS current leads to energize the coil; the control and instrumentation equipment (sensors, PLC's, supervision system, fast data acquisition system, etc.) and the Magnet Safety System (MSS) that protects the coils in case of quench. The paper will give an overview of the design of this large facility and the status of its realization.

  19. Qualification and preparatory activities for the manufacturing of 9 TF coils of the JT-60SA magnet

    International Nuclear Information System (INIS)

    Cucchiaro, Antonio; Polli, Gian Mario; Cocilovo, Valter; Drago, Giovanni; Cuneo, Stefano; Terzi, Franco; Peyrot, Marc; Phillips, Guy; Tomarchio, Valerio

    2013-01-01

    In the framework of the Broader Approach Agreement for the construction of the JT-60SA tokamak, ENEA is in charge to provide 9 of the 18 Toroidal Field (TF) coils. The 9 coils are being manufactured by ASG superconductors in Genoa under the supervision of ENEA in collaboration with the JT-60SA European home team. Prior the manufacturing, a preparatory activity has been carried out aimed at designing, constructing and setting-up the relevant components to be realized. In order to get confidence of some special manufacturing process, several qualification activities have been performed. In this paper an overview of the principal milestones reached during the preparatory phase and a description of the qualification activities with relevant test results are presented

  20. Long Pulse Operation on NBI Systems for JT-60U

    International Nuclear Information System (INIS)

    Akino, N.; Ebisawa, N.; Honda, A.; Ikeda, Y.; Kawai, M.; Kazawa, M.; Mogaki, K.; Ohga, T.; Umeda, N.; Usui, K.; Yamamoto, T.; Grisham, L.

    2005-01-01

    In the neutral beam injection (NBI) system, an extension of the pulse duration up to 30 sec has been intended to study quasi-steady state plasma on JT-60U. The four positive-ion based (P-NBI) units, which tangentially inject neutral beam to plasma, were mainly modified on the electric power supplies and the beam limiters to extend the pulse duration up to 30 sec with 2 MW at 80 keV per each. The seven P-NBI units, each of which perpendicularly injects for 10 sec, were conducted to operate in series for the total pulse duration of 30 sec. The ion source of the negative-ion based (N-NBI) unit, whose target beam energy is 500 keV for 10 sec, was also modified to reduce the heat load of the grid for long pulse operation. The reduction of the re-ionization of the neutral beam in the beam drift duct was a key to achieve a long pulse injection. It was found that the pressure rise in the beam drift duct, which gives the re-ionization rate, depended on the temperature of the re-ionization plates during NBI injection. Up to now, it was attained successfully that the pulse duration of the tangential P-NBI unit was extended up to 30 sec. 310 MJ of the total integrated injection energy into JT-60U plasma was achieved, including the negative-ion based NBI operation for 17 sec at 366 keV

  1. Prospective performances in JT-60SA towards the ITER and DEMO relevant plasmas

    International Nuclear Information System (INIS)

    Tamai, H.; Fujita, T.; Kikuchi, M.

    2006-01-01

    JT-60SA, the former JT-60SC and NCT, a superconducting tokamak positioned as the satellite machine of ITER, collaborating with Japan and EU fusion community, aims at contribution to ITER and DEMO through the demonstration of advanced plasma operation scenario and the plasma applicability test with advanced materials. After the discussions in JA-EU Satellite Tokamak Working Group in 2005, the increased heating power, higher heat removal capacity for the plasma facing components, improvement of the radiation shielding, the remote handling system for the maintenance of in-vessel components, and related equipment are planed to be additionally installed. With such full equipment towards the increased heating power of 41 MW (34 MW-NBI and 7 MW-ECH) with 100 s, the prospective plasma performances, analysed by the equilibrium and transport analysis codes, are rather improved in the view point of the contribution to ITER and DEMO relevant research. Accessibility for higher heating power in a higher density region enables the lower normalized Larmor radius and normalized collision frequency close to the reactor relevant plasma with the ITER-similar configuration of single null divertor plasma with the aspect ratio of A = 3.1, elongation of k95 = 1.7, triangularity of d95 (q95) in the plasma current of I p = 3.5 MA, toroidal magnetic field of B T = 2.59 T and the major radius of Rp=3.16 m. The increases in the electron temperature, beam driven and bootstrap current fraction by the increase of the power of Negative ion based NBI (10 MW) reduce the loop voltage and contribute to increase the maximum plasma current of ITER similar shape. Full non-inductive current drive controllability is also extended into the high density and high plasma current operation towards high beta plasma. Flexibility in aspect ratio and shape parameter is kept the same as NCT, i.e. a double null divertor plasma with A = 2.6, k95 = 1.83, d95 = 0.57, I p = 5.5 MA, B T = 2.72 T, and R p = 3.01 m which

  2. The deep-sea hub of the ANTARES neutrino telescope

    Energy Technology Data Exchange (ETDEWEB)

    Anghinolfi, M. [INFN Sezione di Genova, Via Dodecaneso 33, I-16146 Genova (Italy); Calzas, A. [Centre de Physique des Particules de Marseille (CNRS/IN2P3), Universite de la Mediterranee, 13288 Marseille (France); Dinkespiler, B. [Centre de Physique des Particules de Marseille (CNRS/IN2P3), Universite de la Mediterranee, 13288 Marseille (France); Cuneo, S. [INFN Laboratori Nazionali del Sud, Via S. Sofia 44, I-95123 Catania (Italy); Favard, S. [Centre de Physique des Particules de Marseille (CNRS/IN2P3), Universite de la Mediterranee, 13288 Marseille (France); Hallewell, G. [Centre de Physique des Particules de Marseille (CNRS/IN2P3), Universite de la Mediterranee, 13288 Marseille (France)]. E-mail: gregh@cppm.in2p3.fr; Jaquet, M. [Centre de Physique des Particules de Marseille (CNRS/IN2P3), Universite de la Mediterranee, 13288 Marseille (France); Musumeci, M. [INFN Laboratori Nazionali del Sud, Via S. Sofia 44, I-95123 Catania (Italy); Papaleo, R. [INFN Laboratori Nazionali del Sud, Via S. Sofia 44, I-95123 Catania (Italy); Raia, G. [INFN Laboratori Nazionali del Sud, Via S. Sofia 44, I-95123 Catania (Italy); Valdy, P. [IFREMER - Institut francais de recherche pour l' exploitation de la mer, Centre de La Seyne, 83500 La Seyne sur mer (France); Vernin, P. [DSM-DAPNIA, CEA SACLAY, 91191 Gif sur Yvette Cedex (France)

    2006-11-15

    The ANTARES neutrino telescope, currently under construction at 2500 m depth off the French Mediterranean coast, will contain 12 detection lines, powered and read out through a deep-sea junction box (JB) hub. Electrical energy from the shore station is distributed through a transformer with multiple secondary windings and a plugboard with 16 deep sea-mateable electro-optic connectors. Connections are made to the JB outputs using manned or remotely operated submersible vehicles. The triply redundant power management and slow control system is based on two identical AC-powered systems, communicating with the shore through 160 Mb/s fibre G-links and a third battery-powered system using a slower link. We describe the power and slow control systems of the underwater hub.

  3. The deep-sea hub of the ANTARES neutrino telescope

    International Nuclear Information System (INIS)

    Anghinolfi, M.; Calzas, A.; Dinkespiler, B.; Cuneo, S.; Favard, S.; Hallewell, G.; Jaquet, M.; Musumeci, M.; Papaleo, R.; Raia, G.; Valdy, P.; Vernin, P.

    2006-01-01

    The ANTARES neutrino telescope, currently under construction at 2500 m depth off the French Mediterranean coast, will contain 12 detection lines, powered and read out through a deep-sea junction box (JB) hub. Electrical energy from the shore station is distributed through a transformer with multiple secondary windings and a plugboard with 16 deep sea-mateable electro-optic connectors. Connections are made to the JB outputs using manned or remotely operated submersible vehicles. The triply redundant power management and slow control system is based on two identical AC-powered systems, communicating with the shore through 160 Mb/s fibre G-links and a third battery-powered system using a slower link. We describe the power and slow control systems of the underwater hub

  4. The application of design criteria for locating a hub configured supply chain for a restaurant cluster in the Stellenbosch area

    Directory of Open Access Journals (Sweden)

    Claudia B. Struwig

    2013-06-01

    Full Text Available Restaurants, in general, utilise numerous suppliers. Normally they deliver on different days in the week and at different times during the day, logistically not an optimum approach. Not only does the current practice cause frequent interruptions, but by segregating the food supply chain unnecessary traffic is generated. This article investigated the need for developing a third party supplier hub, the best positioning of that hub and the most economical routes to the customers. With the aim of providing non-franchised restaurants with the necessary leverage to become market leaders, the hub is planned to only service the restaurants within the vicinity of the Stellenbosch area. In such a hub-configured supply chain, the suppliers would be delivering to the proposed hub, from where once-off deliveries to all the restaurants may be made on days and/or times determined by them. In order to investigate the benefits of providing such a hub structure, a systematic implementation approach was used. The first step was to do market research in order to establish the need for such a hub. That is, the viability of the hub from a restaurant’s perspective was established. The next step entailed the investigation of the design criteria needed in determining a favourable hub location. Four possible hub locations were identified. The Clark and Wright’s savings algorithm was then used to determine the optimal hub location and the feasibility of the results was verified with the aid of a global positioning system (GPS device. The last steps followed involved the determination of an effective hub floor plan that may be utilised, possible products that can be supplied to the restaurants and the necessary assets needed to provide the hub’s service. Finally, by incorporating all these facets, a cost analysis was done to determine the hub’s profitability.

  5. Gravity drives the evolution of infrared dark hubs: JVLA observations of SDC13

    Science.gov (United States)

    Williams, G. M.; Peretto, N.; Avison, A.; Duarte-Cabral, A.; Fuller, G. A.

    2018-05-01

    Context. Converging networks of interstellar filaments, that is hubs, have been recently linked to the formation of stellar clusters and massive stars. Understanding the relationship between the evolution of these systems and the formation of cores and stars inside them is at the heart of current star formation research. Aims: The goal is to study the kinematic and density structure of the SDC13 prototypical hub at high angular resolution to determine what drives its evolution and fragmentation. Methods: We have mapped SDC13, a 1000 M⊙ infrared dark hub, in NH3(1,1) and NH3(2,2) emission lines, with both the Jansky Very Large Array and Green Bank Telescope. The high angular resolution achieved in the combined dataset allowed us to probe scales down to 0.07 pc. After fitting the ammonia lines, we computed the integrated intensities, centroid velocities and line widths, along with gas temperatures and H2 column densities. Results: The mass-per-unit-lengths of all four hub filaments are thermally super-critical, consistent with the presence of tens of gravitationally bound cores identified along them. These cores exhibit a regular separation of 0.37 ± 0.16 pc suggesting gravitational instabilities running along these super-critical filaments are responsible for their fragmentation. The observed local increase of the dense gas velocity dispersion towards starless cores is believed to be a consequence of such fragmentation process. Using energy conservation arguments, we estimate that the gravitational to kinetic energy conversion efficiency in the SDC13 cores is 35%. We see velocity gradient peaks towards 63% of cores as expected during the early stages of filament fragmentation. Another clear observational signature is the presence of the most massive cores at the filaments' junction, where the velocity dispersion is largest. We interpret this as the result of the hub morphology generating the largest acceleration gradients near the hub centre. Conclusions: We

  6. Strategic analysis on establishing a natural gas trading hub in China

    Directory of Open Access Journals (Sweden)

    Xiaoguang Tong

    2014-12-01

    Full Text Available Since 2010, the LNG importing price premium in the Asia–Pacific markets has become increasingly high, generating great effects on the economic development in China. In addition, the natural gas dependence degree is expanding continuously, making it extremely urgent to establish a natural gas trading hub in China, with the aim to ensure national energy security, to gain the pricing power, and to build the regional benchmark prices. Through a comparative analysis of internal strength/weakness and external competitiveness, we concluded that with intensively-issued supporting policies on the natural gas sector, the initiation of spot and futures markets, the rapid growth of gas production and highly-improved infrastructures, as well as Shanghai's advantageous location, China has more advantages in establishing an Asian Natural Gas Trading Hub than other counties like Singapore, Japan and Malaysia. Moreover, based on the SWOT (strength, weakness, opportunity and threat and the marketization process analysis, the following strategies were presented: to impel the establishment of a natural gas trading hub depending on the gas supply condition, to follow the policies to complete the gas storage system, to form regional communities by taking comparative advantages, and to reinforce the marketization reform and regulation system establishment with foreign experiences for reference. This study rationalized the necessity and practicality of establishing a natural gas trading hub in China and will help China make a proper decision and find a periodical strategic path in this sector.

  7. A preliminary assessment of the potential for 'team science' in DOE Energy Innovation Hubs and Energy Frontier Research Centers

    Energy Technology Data Exchange (ETDEWEB)

    Boardman, Craig, E-mail: boardman.10@osu.edu [John Glenn School of Public Affairs, Ohio State University (United States); Ponomariov, Branco, E-mail: branco.ponomariov@utsa.edu [Department of Public Administration, University of Texas at San Antonio (United States)

    2011-06-15

    President Obama has called for the development of new energy technologies to address our national energy needs and restore US economic competitiveness. In response, the Department of Energy has established new R and D modalities for energy research and development designed to facilitate collaboration across disciplinary, institutional, and sectoral boundaries. In this research note, we provide a preliminary assessment of the potential for essential mechanisms for coordinated problem solving among diverse actors within two new modalities at the DOE: Energy Innovation Hubs and Energy Frontier Research Centers. - Highlights: > Energy Frontier Research Centers may lack the basic mechanisms for coordinating diverse actors. > Divergent goals across diverse actors may hinder coordination in Energy Innovation Hubs. > The implementation of these and similar energy policies require further investigation.

  8. NMR structural studies of the ionizing radiation adduct 7-hydro-8-oxodeoxyguanosine (8-oxo-7H-dG) opposite deoxyadenosine in a DNA duplex. 8-oxo-7H-dG(syn)·dA(anti) alignment at lesion site

    International Nuclear Information System (INIS)

    Kouchakdjian, M.; Patel, D.J.; Bodepudi, V.; Shibutani, S.; Eisenberg, M.; Johnson, F.; Grollman, A.P.

    1991-01-01

    Proton NMR studies are reported on the complementary d(C1-C2-A3-C4-T5-A6-oxo-G7-T8-C9-A10-C11-C12)·d(G13-G14-T15-G16-A17-A18-T19-A20-G21-T22-G23-G24) dodecanucleotide duplex (designated 8-oxo-7H-dG·dA 12-mer), which contains a centrally located 7-hydro-8-oxodeoxyguanosine (8-oxo-7H-dG) residue, a group commonly found in DNA that has been exposed to ionizing radiation or oxidizing free radicals. From the NMR spectra it can be deduced that this moiety exists as two tautomers, or gives rise to two DNA conformations, that are in equilibrium and that exchange slowly. The present study focuses on the major component of the equilibrium that originates in the 6,8-dioxo tautomer of 8-oxo-7H-dG. The authors have assigned the exchangeable NH1, NH7, and NH 2 -2 base protons located on the Watson-Crick and Hoogsteen edges of 8-oxo-7H-dG7 in the 8-oxo-7H-dG·dA 12-mer duplex, using an analysis of one- and two-dimensional nuclear Overhauser enhancement (NOE) data in H 2 O solution. They were able to detect a set of intra- and interstrand NOEs between protons (exchangeable and nonexchangeable) on adjacent residues in the d(A6-oxo-G7-T8d(A17-A18-T19) trinucleotide segment centered about the lesion site that establishes stacking of the oxo-dG7(syn)·dA(anti) pair between stable Watson-Crick dA6·dT19 and dT8·A17 base pairs with minimal perturbation of the helix. The structural studies demonstrate that 8-oxo-7H-dG(syn)·dA(anti) forms a stable pair in the interior of the helix, providing a basis for the observed incorporation of dA opposite 8-oxo-7H-dG when readthrough occurs past this oxidized nucleoside base

  9. Pyrrolizidine Alkaloids from Symphytum sylvaticum Boiss. subsp. sepulcrale. (Boiss.& Bal.) Greuter & Burdetvar. sepulcrale and Symphytum aintabicum Hub.- Mor. & Wickens

    OpenAIRE

    KURUCU, Semra; KARTAL, Murat

    2002-01-01

    Pyrrolizidine alkaloid (Echimidine-N-oxide) was isolated from Symphytum sylvaticum Boiss. subsp. sepulcrale (Boiss. & Bal.) Greuter & Burdet var. sepulcrale and pyrrolizidine alkaloid (Echimidine) was isolated from Symphytum aintabicum Hub. - Mor. & Wickens. The structures of the isolated compounds were elucidated based on IR, EIMS, 1H, and 13C NMR analysis and also on 2D NMR (COSY, HMBC, HMQC) experiments.

  10. Avoidance of VDEs during plasma current quench in JT-60U

    International Nuclear Information System (INIS)

    Yoshino, R.; Nakamura, Y.; Neyatani, Y.

    1996-01-01

    Vertical displacement events (VDEs) during plasma current quench (I p quench) are one of the serious problems encountered in designing tokamak fusion reactors, owing to the generation of enormously high electromagnetic forces on the vacuum vessel and in-vessel components, but they have been passively and actively avoided in JT-60U. In JT-60U 'slow I p quench' is ended with very fast plasma current termination (final I p termination), and the halo current is frequently measured at this final I p termination. VDEs make the final I p termination severe by increasing the halo current and the electromagnetic force. A strong dependence of VDE growth rate on the initial vertical position of the plasma current centre (Z J ) has been clarified experimentally, and a neutral point of Z J for VDE has been found at ∼ 15 cm above the midplane of the vacuum vessel. According to these measurements, VDE has been avoided by the selection of Z J at the start of I p quench (passive control) and by the control of Z J during I p quench (active control) eventually obtained owing to the small deviation of Z J in real time calculations from its actual value. Furthermore, passive avoidance of VDEs by the injection of a neon ice pellet has been demonstrated. (author). 29 refs, 14 figs

  11. nanoHUB.org: Experiences and Challenges in Software Sustainability for a Large Scientific Community

    Directory of Open Access Journals (Sweden)

    Lynn Zentner

    2014-07-01

    Full Text Available The science gateway nanoHUB.org, funded by the National Science Foundation (NSF, serves a large scientific community dedicated to research and education in nanotechnology with community-contributed simulation codes as well as a vast repository of other materials such as recorded presentations, teaching materials, and workshops and courses. Nearly 330,000 users annually access over 4400 items of content on nanoHUB, including 343 simulation tools. Arguably the largest nanotechnology facility in the world, nanoHUB has led the way not only in providing open access to scientific code in the nanotechnology community, but also in lowering barriers to the use of that code, by providing a platform where developers are able to easily and quickly deploy code written in a variety of languages with user-friendly graphical user interfaces and where users can run the latest versions of codes transparently on the grid or other powerful resources without ever having to download or update code. Being a leader in open access code deployment provides nanoHUB with opportunities and challenges as it meets the current and future needs of its community. This paper discusses the experiences of nanoHUB in addressing and adapting to the changing landscape of scientific software in ways that best serve its community and meet the needs of the largest portion of its user base.

  12. Googling Service Boundaries for Endovascular Clot Retrieval Hub Hospitals in a Metropolitan Setting: Proof-of-Concept Study.

    Science.gov (United States)

    Phan, Thanh G; Beare, Richard; Chen, Jian; Clissold, Benjamin; Ly, John; Singhal, Shaloo; Ma, Henry; Srikanth, Velandai

    2017-05-01

    There is great interest in how endovascular clot retrieval hubs provide services to a population. We applied a computational method to objectively generate service boundaries for such endovascular clot retrieval hubs, defined by traveling time to hub. Stroke incidence data merged with population census to estimate numbers of stroke in metropolitan Melbourne, Australia. Traveling time from randomly generated addresses to 4 endovascular clot retrieval-capable hubs (Royal Melbourne Hospital [RMH], Monash Medical Center [MMC], Alfred Hospital [ALF], and Austin Hospital [AUS]) estimated using Google Map application program interface. Boundary maps generated based on traveling time at various times of day for combinations of hubs. In a 2-hub model, catchment was best distributed when RMH was paired with MMC (model 1a, RMH 1765 km 2 and MMC 1164 km 2 ) or with AUS (model 1c, RMH 1244 km 2 and AUS 1685 km 2 ), with no statistical difference between models ( P =0.20). Catchment was poorly distributed when RMH was paired with ALF (model 1b, RMH 2252 km 2 and ALF 676 km 2 ), significantly different from both models 1a and 1c (both P AUS was superior to that of RMH, MMC, and ALF in catchment distribution and travel time. The method was also successfully applied to the city of Adelaide demonstrating wider applicability. We provide proof of concept for a novel computational method to objectively designate service boundaries for endovascular clot retrieval hubs. © 2017 American Heart Association, Inc.

  13. Effect of halo current and its toroidal asymmetry during disruptions in JT-60U

    International Nuclear Information System (INIS)

    Neyatani, Y.; Yoshino, R.; Ando, T.

    1995-01-01

    A poloidal halo current due to a vertical displacement event (VDE) is observed in experimentally simulated VDE discharges and density limit disruptions in the JT-60U tokamak. In the case of a clockwise I p and B T discharge, the halo current flows into the vacuum vessel from the inside separatrix and goes back to the plasma from the outside separatrix. A maximum halo current is produced by a change in the poloidal flux generated by plasma current decay. A toroidal asymmetry factor of 2.5 is estimated from the requirements of the fracture of the carbon-fiber composite tiles. The toroidal asymmetry is caused by the poloidal field (PF) that is produced by the toroidal field (TF) ripple, the deformation of the vacuum vessel, the setting error between the vacuum vessel and the TF and PF coils, the low-n mode during current quench, etc. To consider this asymmetry, in JT-60U, one must estimate the total halo current as nearly 26% of the plasma current just before a current quench. 25 refs., 10 figs

  14. Hub River: A private power prototype

    International Nuclear Information System (INIS)

    Sachs, J.L.

    1992-01-01

    This article examines the challenges of financing an independent power project in a developing country. The oil-fired plant is to be located on the Hub River in Baluchistan on the Arabian Sea coast. The topics of the article include a description of the team that put the project together, the financing plans, the risk in the face of political unrest and change of governments, and the beginning of construction of the project

  15. Addressing congestion on single allocation hub-and-spoke networks

    Directory of Open Access Journals (Sweden)

    Ricardo Saraiva de Camargo

    2012-12-01

    Full Text Available When considering hub-and-spoke networks with single allocation, the absence of alternative routes makes this kind of systems specially vulnerable to congestion effects. In order to improve the design of such networks, congestion costs must be addressed. This article deploys two different techniques for addressing congestion on single allocation hub-and-spoke networks: the Generalized Benders Decomposition and the Outer Approximation method. Both methods are able to solve large scale instances. Computational experiments show how the adoption of advanced solution strategies, such as Pareto-optimal cut generation on the Master Problem branch-and-bound tree, may be decisive. They also demonstrate that the solution effort is not only associated with the size of the instances, but also with their combination of the installation and congestion costs.

  16. CYP2D6 Genetic Variation and Beta-Blocker Maintenance Dose in Patients with Heart Failure.

    Science.gov (United States)

    Luzum, Jasmine A; Sweet, Kevin M; Binkley, Philip F; Schmidlen, Tara J; Jarvis, Joseph P; Christman, Michael F; Sadee, Wolfgang; Kitzmiller, Joseph P

    2017-08-01

    This study examined whether a CYP2D6 polymorphism (CYP2D6*4) was related to beta-blocker maintenance dose in patients with heart failure. Logistic regression modeling was utilized in a retrospective chart-review analysis of heart-failure patients (60% Male, 90% of European descent) to assess whether CYP2D6*4 (non-functional CYP2D6 allele present in 1 of 5 individuals of European descent) is associated with maintenance dose of carvedilol (n = 65) or metoprolol (n = 33). CYP2D6*4 was associated with lower maintenance dose of metoprolol (OR 0.13 [95% CI 0.02-0.75] p = 0.023), and a trend was observed between CYP2D6*4 and higher maintenance dose of carvedilol (OR 2.94 [95% CI 0.84-10.30] p = 0.093). None of the patients that carried CYP2D6*4 achieved the recommended target dose of metoprolol (200 mg/day). Consistent with the role of CYP2D6 in the metabolism of metoprolol, the tolerated maintenance dose of metoprolol was lower in CYP2D6*4 carriers compared to non-carriers. Consistent with the role of CYP2D6 in activation of carvedilol, tolerated maintenance dose of carvedilol was higher in CYP2D6*4 carriers compared to non-carriers. Further investigation is warranted to ascertain the potential of CYP2D6 as a potential predictive biomarker of beta-blocker maintenance dose in heart failure patients.

  17. Development of passive-controlled HUB (teetered brake & damper mechanism) of horizontal axis wind turbine

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Yukimaru; Kamada, Yasunari; Maeda, Takao [Mie Univ. (Japan)

    1997-12-31

    For the purpose of the improvement of reliability of the Mega-Watt wind turbine, this paper indicates the development of an original mechanism for the passive-controlled hub, which has the effects of braking and damping on aerodynamic forces. This mechanism is useful for variable speed control of the large wind turbine. The passive-controlled hub is the combination of two mechanisms. One is the passive-teetered and damping mechanism, and the other is the passive-variable-pitch mechanism. These mechanism are carried out by the combination of the teetering and feathering motions. When the wind speed exceeds the rated wind speed, the blade is passively teetered in a downwind direction and, simultaneously, a feathering mechanism, which is linked to the teetering mechanism through a connecting rods, is activated. Testing of the model horizontal axis wind turbine in a wind tunnel showed that the passive-controlled hub mechanism can suppress the over-rotational speed of the rotor. By the application of the passive-controlled hub mechanism, the maximum rotor speed is reduced to about 60%.

  18. Gas and LNG pricing and trading hub in East Asia: An introduction

    OpenAIRE

    Shi, Xunpeng

    2017-01-01

    This paper summarizes the four papers in the special issues on ‘Gas and LNG pricing and trading hub in East Asia’. The papers examine lessons and experience from European hub development, other commodity, the Japanese history on developing of futures markets and inter-fuel substitution in East Asia. The papers finds that liquid futures market is the key to formulate benchmark prices while a well-developed spot market is the foundation; political will and strong leadership are required to over...

  19. Design and characteristics of the drive mechanism for movable limiters of JT-60, (1)

    International Nuclear Information System (INIS)

    Takashima, Tetsuo; Morishita, Osamu; Yamamoto, Masahiro; Shimizu, Masatsugu; Ohta, Mitsuru

    1976-10-01

    Two fast-acting movable rail limiters will be installed in a large Tokamak JT-60 being designed in JAERI. The movable limiter consists of a drive mechanism, a vacuum seal, a bearing, and a molybdenum rail limiter. Design of the drive mechanism for the movable limiter and experimental results on the driving characteristics in full scale are described. (auth.)

  20. Heat analysis of the magnetic limiter plate for JT-60

    International Nuclear Information System (INIS)

    Nakamura, Hiroo; Ninomiya, Hiromasa; Shimizu, Masatsugu; Ohta, Mitsuru

    1977-03-01

    Heat analysis has been made of the magnetic limiter plate for JT-60. Test materials of the magnetic limiter plate are molybdenum, graphite, pyrolytic graphite and silicon carbide. It is assumed in calculation of the heat analysis that 10MW is deposited on the 2 cm wide surface of the magnetic limiter plate in about 10 sec. The magnetic limiter plate of pyrolytic graphite is a stack of pyrolytic graphite sheets, heat input is in the deposition plane to take advantage of the large heat conductivity along this plane. Pyrolytic graphite is the best in terms of temperature rise. The temperature of molybdenum and graphite rise up to 1800 0 C and 620 0 C, respectively, in an deposition of 10 MWx10sec. Silicon carbide is not suitable for the magnetic limiter plate. Because the plasma of the JT-60 discharges every 10 min, the average heat flux decreases to 17 w/cm 2 during the each interval. When the magnetic limiter plate has the above heat inflow, a maximum of above 1000 0 C occurs at the edge far from the joint to the thick ring of the vacuum vessel. To reduce heat load of the magnetic limiter plate, an alternating current (2 -- 5Hz) is superposed on the magnetic limiter coil current. The intersection of separatrix line and magnetic limiter plate then moves cyclically more than 10 cm. Concerning temperature distribution of the multi-groove magnetic limiter plate, its dimensions are determined by the limitation in vapor pressure to prevent the impurity inflow. (auth.)

  1. Advanced tokamak research with integrated modeling in JT-60 Upgrade

    International Nuclear Information System (INIS)

    Hayashi, N.

    2010-01-01

    Researches on advanced tokamak (AT) have progressed with integrated modeling in JT-60 Upgrade [N. Oyama et al., Nucl. Fusion 49, 104007 (2009)]. Based on JT-60U experimental analyses and first principle simulations, new models were developed and integrated into core, rotation, edge/pedestal, and scrape-off-layer (SOL)/divertor codes. The integrated models clarified complex and autonomous features in AT. An integrated core model was implemented to take account of an anomalous radial transport of alpha particles caused by Alfven eigenmodes. It showed the reduction in the fusion gain by the anomalous radial transport and further escape of alpha particles. Integrated rotation model showed mechanisms of rotation driven by the magnetic-field-ripple loss of fast ions and the charge separation due to fast-ion drift. An inward pinch model of high-Z impurity due to the atomic process was developed and indicated that the pinch velocity increases with the toroidal rotation. Integrated edge/pedestal model clarified causes of collisionality dependence of energy loss due to the edge localized mode and the enhancement of energy loss by steepening a core pressure gradient just inside the pedestal top. An ideal magnetohydrodynamics stability code was developed to take account of toroidal rotation and clarified a destabilizing effect of rotation on the pedestal. Integrated SOL/divertor model clarified a mechanism of X-point multifaceted asymmetric radiation from edge. A model of the SOL flow driven by core particle orbits which partially enter the SOL was developed by introducing the ion-orbit-induced flow to fluid equations.

  2. Type D personality and cardiac mortality in patients with chronic heart failure

    DEFF Research Database (Denmark)

    Schiffer, Angélique A; Smith, Otto R F; Pedersen, Susanne S.

    2010-01-01

    Clinical predictors of cardiac mortality in chronic heart failure (CHF) are established, but less is known about chronic psychological predictors. Therefore, we examined the prognostic value of Type D personality (tendency to experience negative feelings and inhibit self-expression) in CHF patients....

  3. Continuous Integration for Concurrent MOOSE Framework and Application Development on GitHub

    Directory of Open Access Journals (Sweden)

    Andrew E. Slaughter

    2015-11-01

    Full Text Available For the past several years, Idaho National Laboratory’s MOOSE framework team has employed modern software engineering techniques (continuous integration, joint application/framework source code repos- itories, automated regression testing, etc. in developing closed-source multiphysics simulation software (Gaston et al., 'Journal of Open Research Software' vol. 2, article e10, 2014. In March 2014, the MOOSE framework was released under an open source license on GitHub, significantly expanding and diversifying the pool of current active and potential future contributors on the project. Despite this recent growth, the same philosophy of concurrent framework and application development continues to guide the project’s development roadmap. Several specific practices, including techniques for managing multiple repositories, conducting automated regression testing, and implementing a cascading build process are discussed in this short paper. Special attention is given to describing the manner in which these practices naturally synergize with the GitHub API and GitHub-specific features such as issue tracking, Pull Requests, and project forks.

  4. Development of residual thermal stress-relieving structure of CFC monoblock target for JT-60SA divertor

    Energy Technology Data Exchange (ETDEWEB)

    Tsuru, Daigo, E-mail: tsuru.daigo@jaea.go.jp; Sakurai, Shinji; Nakamura, Shigetoshi; Ozaki, Hidetsugu; Seki, Yohji; Yokoyama, Kenji; Suzuki, Satoshi

    2015-10-15

    Highlights: • We carried out numerical simulations on residual thermal stress of targets for the JT-60SA divertor. • We developed three measures to reduce residual thermal stress. • We proposed two structures of CFC monoblock target for the JT-60SA divertor. • We confirmed the effectiveness of the structure by infrared thermography inspection and high heat flux test. - Abstract: Carbon fibre-reinforced carbon composite (CFC) monoblock target for JT-60SA divertor is under development towards the mass-production. CFC monoblocks, WCu interlayers and a CuCrZr cooling tube at the centre of the monoblocks were bonded by vacuum brazing in a high temperature, to a target. If residual thermal stress due to difference of thermal expansions between CFC and CuCrZr exceeds the maximum allowable stress of the CFC after the bonding, cracks are generated in the CFC monoblock and heat removal capacity of the target degrades. In this paper, new structures of the targets were proposed, to reduce residual thermal stress and to mitigate the degradation of heat removal capacity of the targets. Some measures, including slitting of the CFC monoblock aside of the cooling tube, replacement of the interlayer material and shifting the position of the cooling tube, were implemented. The effectiveness of the measures was evaluated by numerical simulations. Target mock-ups with the proposed structures were manufactured. Infrared thermography inspection and high heat flux test were carried out on the mock-ups in order to evaluate the heat removal capacity.

  5. Characteristics of steady vibration in a rotating hub-beam system

    Science.gov (United States)

    Zhao, Zhen; Liu, Caishan; Ma, Wei

    2016-02-01

    A rotating beam features a puzzling character in which its frequencies and modal shapes may vary with the hub's inertia and its rotating speed. To highlight the essential nature behind the vibration phenomena, we analyze the steady vibration of a rotating Euler-Bernoulli beam with a quasi-steady-state stretch. Newton's law is used to derive the equations governing the beam's elastic motion and the hub's rotation. A combination of these equations results in a nonlinear partial differential equation (PDE) that fully reflects the mutual interaction between the two kinds of motion. Via the Fourier series expansion within a finite interval of time, we reduce the PDE into an infinite system of a nonlinear ordinary differential equation (ODE) in spatial domain. We further nondimensionalize the ODE and discretize it via a difference method. The frequencies and modal shapes of a general rotating beam are then determined numerically. For a low-speed beam where the ignorance of geometric stiffening is feasible, the beam's vibration characteristics are solved analytically. We validate our numerical method and the analytical solutions by comparing with either the past experiments or the past numerical findings reported in existing literature. Finally, systematic simulations are performed to demonstrate how the beam's eigenfrequencies vary with the hub's inertia and rotating speed.

  6. Reduced transport and ER shearing in improved confinement regimes in JT-60U

    International Nuclear Information System (INIS)

    Shirai, H.; Kikuchi, M.; Takizuka, T.

    2001-01-01

    The global confinement and the local transport properties of improved core confinement plasmas in JT-60U have been studied in connection with E r shear formation. The improved core confinement mode with ITB, the internal transport barrier, is roughly classified into 'parabolic' type ITBs and 'box' type ITBs. The parabolic type ITB has the reduced thermal diffusivity, χ, in the core region; however, the E r shear, dE r /dr, is not so strong. The box type ITB has a very strong E r shear at the thin ITB layer and the χ value decreases to the level of neoclassical transport there. The estimated ExB shearing rate, ω ExB , becomes almost the same as the linear growth rate of the drift microinstability, γ L , at the ITB layer in the box type ITB. Experiments of hot ion mode plasmas during the repetitive L-H-L transition shows that the thermal diffusivity clearly depends on the E r shear and the strong E r shear contributes to the reduced thermal diffusivity. (author)

  7. Reduced transport and Er shearing in improved confinement regimes in JT-60U

    International Nuclear Information System (INIS)

    Shirai, H.; Kikuchi, M.; Takizuka, T.

    1999-01-01

    The global confinement and the local transport properties of improved core confinement plasmas in JT-60U were studied in connection with E r shear formation. In the improved core confinement mode with internal transport barriers (ITBs), these are roughly classified into 'parabolic type' ITBs and 'box type' ITBs. The parabolic type ITB has a reduced thermal diffusivity χ in the core region; however, the E r shear, dE r /dr, is not as strong. The box type ITB has a very strong E r shear at the thin ITB layer and χ decreases to the level of neoclassical transport there. The estimated E x B shearing rate, ω ExB , becomes almost the same as the linear growth rate of the drift microinstability, γ L , at the ITB layer in the box type ITB. Experiments with hot ion mode plasmas during the repetitive L-H-L transition showed that the thermal diffusivity clearly depends on the E r shear and the strong E r shear contributes to the reduced thermal diffusivity. (author)

  8. Ferritic insertion for reduction of toroidal magnetic field ripple on JT-60U

    International Nuclear Information System (INIS)

    Shinohara, K.; Sakurai, S.; Ishikawa, M.; Tsuzuki, K.; Suzuki, Y.; Masaki, K.; Naito, O.; Kurihara, K.; Suzuki, T.; Koide, Y.; Fujita, T.; Miura, Y.

    2007-01-01

    Ferritic steel tiles (FSTs) have been installed to improve the energetic ion confinement by reducing a toroidal magnetic field ripple. Aiming at cost-effective installation, orbit-following calculations of energetic ions were carried out for a design of the installation of ferritic steel on the JT-60U by using the fully three dimensional magnetic field orbit-following Monte-Carlo (F3D OFMC) code, which had been developed for ferritic insert experiments on the JFT-2M and can treat the complex magnetic field structure produced by ferritic inserts. The installed FSTs add a non-linear magnetic field on magnetic sensors for plasma control and an equilibrium calculation. The code for real-time control has been modified to take into account the magnetic field by the FSTs. The plasma operation was successfully resumed after usual conditioning processes and real-time plasma control was successfully carried out. The heat load measurement indicates the improved confinement of energetic ions. These results are important for practical application of the ferritic steel, which is a leading candidate of a structural material on a DEMO reactor

  9. Energy confinement in JT-60 lower hybrid current driven plasmas

    International Nuclear Information System (INIS)

    Ushigusa, K.; Imai, T.; Naito, O.; Ikeda, Y.; Tsuji, S.; Uehara, K.

    1990-01-01

    The energy confinement in high power lower hybrid current driven (LHCD) plasmas has been studied in the JT-60 tokamak. At a plasma current of 1 MA, the diamagnetically estimated energy confinement time in LHCD plasmas has almost the same value as the confinement time in ohmically heated plasmas at n-bar e ∼ 1.0x10 19 m -3 . The confinement time of high power LHCD plasmas (P LH E varies as to P LH α n e β I p 0 with α + β ∼ -0.3. (author). Letter-to-the-editor. 12 refs, 5 figs

  10. Micromechanics of failure in brittle geomaterials. Final technical report (for 7/1/1994 - 8/31/2000)

    International Nuclear Information System (INIS)

    Wong, Teng-fong

    2000-01-01

    The overall objective was to provide a fundamental understanding of brittle failure processes in porous and compact geomaterials. This information is central to energy-related programs such as oil and gas exploration/production, reservoir engineering, drilling technology, geothermal energy recovery, nuclear waste isolation, and environmental remediation. The effects of key parameters such as grain boundary structure and cementation, damage state, and load path on the deformation and failure model of brittle geomaterials are still largely unknown. The research methodology emphasized the integration of experimental rock mechanical testing, quantitative microscopy, and detailed analysis using fracture mechanics, continuum plasticity theory, and numerical methods. Significant progress was made in elucidating the micromechanics of brittle failure in compact crystalline rocks, as well as high-porosity siliciclastic and carbonate rocks. Substantial effort was expended toward applying a new quantitative three-dimensional imaging technique to geomaterials and for developing enhanced image analysis capabilities. The research is presented under the following topics: technique for imaging the 3-D pore structure of geomaterials; mechanics of compressive failure in sandstone; effect of water on compressive failure of sandstone; micromechanics of compressive failure: observation and model; and the brittle-ductile transition in porous carbonate rocks

  11. The economic impact of Medicare Part D on congestive heart failure.

    Science.gov (United States)

    Dall, Timothy M; Blanchard, Tericke D; Gallo, Paul D; Semilla, April P

    2013-05-01

    Medicare Part D has had important implications for patient outcomes and treatment costs among beneficiaries with congestive heart failure (CHF). This study finds that improved medication adherence associated with expansion of drug coverage under Part D led to nearly $2.6 billion in reductions in medical expenditures annually among beneficiaries diagnosed with CHF and without prior comprehensive drug coverage, of which over $2.3 billion was savings to Medicare. Further improvements in adherence could potentially save Medicare another $1.9 billion annually, generating upwards of $22.4 billion in federal savings over 10 years.

  12. Network performance, hub connectivity potential, and competitive position of primary airports in Asia/Pacific region

    NARCIS (Netherlands)

    Matsumoto, H.; Veldhuis, J.; de Wit, J.; Burghouwt, G.

    2008-01-01

    Recently, hub-and-spoke network configurations are more and more developed in the Asia/Pacific region. In this paper, it is argued that the measurement of network performance in hub-and-spoke systems should take into account the quantity and quality of both direct and indirect connections. The

  13. Review of research on AFPM hub motor

    Directory of Open Access Journals (Sweden)

    Jianguo DAI

    2018-02-01

    Full Text Available The industrialization of new energy vehicles is an important way to promote the sustainable development of automobile industry, and it is also the key measure to solve the problems of energy and environment. As an important type of new energy vehicles, electric vehicles will play an important role in the future competition in the automotive industry, especially in the field of electric vehicle driven by wheel. With the advantages of compact structure, high power density, low working noise and good heat dissipation performance, the AFPM motor has gradually become the preferred object of the hub driving device. Based on the statement of the technical development and research status about AFPM motor, this paper mainly analyzes the engineering application and technical problems of AFPM motor in hub drive, especially the matching of AFPM motor with other systems and the problem of heat dissipation at high load conditions, and looks forward to the key role in the future development of the automotive industry. This paper will play a certain reference and guiding role in the application of AFPM motor in the field of new energy vehicles.

  14. Journal de la Recherche Scientifique de l'Université de Lomé - Vol 8 ...

    African Journals Online (AJOL)

    Efficacite de Portulaca Oleracea Linn. et de extra EGG® dans la stimulation de la ponte d'ceufs chez les poules Isa Brown: Etude comparative · EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT. JT Dougnon, C Anago, TM Kpodekon, AP Edorh, F Loko, M Gbeassor ...

  15. Magnetic Fluctuations during plasma current rise of divertor discharge in JT-60

    International Nuclear Information System (INIS)

    Ushigusa, Kenkichi; Kikuchi, Mitsuru; Hosogane, Nobuyuki; Tsuji, Syunji; Hayashi, Kazuo.

    1986-03-01

    During a current rise phase in the JT-60 divertor discharge, a series of magnetic fluctuations which do not rotate poloidally (phase-locking) is observed. They cause a cooling of plasma periphery and an enhancement of H α emission in the divertor chamber. A significant increase in β P + 1 i /2 with minor disruptions during the phase-locked magnetic fluctuation suggests a relaxation of the current profile in the current rise phase of the divertor discharge. (author)

  16. A PWR PCI failure criterion to burnups of 60 GW·d/t using the ENIGMA code

    International Nuclear Information System (INIS)

    Clarke, A.P.; Tempest, P.A.; Shea, J.H.

    2000-01-01

    A fuel performance modelling code (ENIGMA) has been used to analyse the empirical PCI failure criterion in terms of a clad failure stress as a function of burnup and fast neutron dose. The Studsvik database has been analysed. Results indicate a rising and then saturating failure stress with burnup and fast neutron dose. Using the PCI failure limits, equivalent to 95/95 confidence limits, an ENIGMA stress-based methodology is used to derive PWR PCI failure limits up to 60 GW·d/t U using a conservative assumption that the failure stress does not increase at high burnup and neutron dose. In addition experimental ramp data on gadolinia-doped fuel rods do not indicate any increased susceptibility to PCI failure implying that the UO 2 criterion can be used for gadolinia doped fuel. (author)

  17. GeoTrust Hub: A Platform For Sharing And Reproducing Geoscience Applications

    Science.gov (United States)

    Malik, T.; Tarboton, D. G.; Goodall, J. L.; Choi, E.; Bhatt, A.; Peckham, S. D.; Foster, I.; Ton That, D. H.; Essawy, B.; Yuan, Z.; Dash, P. K.; Fils, G.; Gan, T.; Fadugba, O. I.; Saxena, A.; Valentic, T. A.

    2017-12-01

    Recent requirements of scholarly communication emphasize the reproducibility of scientific claims. Text-based research papers are considered poor mediums to establish reproducibility. Papers must be accompanied by "research objects", aggregation of digital artifacts that together with the paper provide an authoritative record of a piece of research. We will present GeoTrust Hub (http://geotrusthub.org), a platform for creating, sharing, and reproducing reusable research objects. GeoTrust Hub provides tools for scientists to create `geounits'--reusable research objects. Geounits are self-contained, annotated, and versioned containers that describe and package computational experiments in an efficient and light-weight manner. Geounits can be shared on public repositories such as HydroShare and FigShare, and also using their respective APIs reproduced on provisioned clouds. The latter feature enables science applications to have a lifetime beyond sharing, wherein they can be independently verified and trust be established as they are repeatedly reused. Through research use cases from several geoscience laboratories across the United States, we will demonstrate how tools provided from GeoTrust Hub along with Hydroshare as its public repository for geounits is advancing the state of reproducible research in the geosciences. For each use case, we will address different computational reproducibility requirements. Our first use case will be an example of setup reproducibility which enables a scientist to set up and reproduce an output from a model with complex configuration and development environments. Our second use case will be an example of algorithm/data reproducibility, where in a shared data science model/dataset can be substituted with an alternate one to verify model output results, and finally an example of interactive reproducibility, in which an experiment is dependent on specific versions of data to produce the result. Toward this we will use software and data

  18. Penentuan Pelabuhan Hub untuk Crude Palm Oil (CPO Ekspor di Indonesia

    Directory of Open Access Journals (Sweden)

    Eko Andi Haranto

    2013-03-01

    Full Text Available CPO (Crude Palm Oil merupakan salah satu komoditi ekspor terbesar di Indonesia. Moda angkut darat dan sungai menjadi pilihan untuk didistribusikan menuju calon pelabuhan hub. Tugas Akhir ini bertujuan untuk merencanakan pola operasi armada pengangkut CPO, dan penentuan pelabuhan hub untuk ekspor CPO. Metode Transportasi digunakan untuk memilih pabrik pengolahan CPO sebagai pemasok utama. Dari hasil analisis didapatkan bahwa penggunaan moda darat menggunakan truk lebih optimal dibandingkan menggunakan tongkang hal ini dikarenakan kondisi sungai di Kalimantan Tengah yang dangkal. Dengan menggunakan metode transportasi didapatkan empat lokasi pabrik pengolahan minyak kelapa sawit. Pelabuhan hub yang terpilih berlokasi di Bagendang dan Bumi Harjo. Kedua titik tersebut dipilih karena sudah memiliki tangki timbun dan dermaga untuk ekspor CPO, selain itu pemilihan berdasarkan hasil analisa didapatkan biaya dari Pabrik PT. ATLANTIS ke Pelabuhan Bagendang dengan truk berukuran 10 ton memerlukan biaya sebesar Rp. 333.016,25/TRIP/TRUK. Pabrik PT. ATLANTIS II ke Pelabuhan Bagendang Rp. 237.868,75/TRIP/TRUK. Pabrik PT. TIGER ke Pelabuhan Bumi Harjo Rp. 475.737,50/TRIP/TRUK. PT. TIGER II merupakan pabrik yang dapat melakukan pengiriman langsung menggunakan tongkang berukuran 1800 DWT melewati sungai Barito, dengan biaya Rp.123.007.828,27,- /voyage.

  19. D-dimer as marker for microcirculatory failure: correlation with LOD and APACHE II scores.

    Science.gov (United States)

    Angstwurm, Matthias W A; Reininger, Armin J; Spannagl, Michael

    2004-01-01

    The relevance of plasma d-dimer levels as marker for morbidity and organ dysfunction in severely ill patients is largely unknown. In a prospective study we determined d-dimer plasma levels of 800 unselected patients at admission to our intensive care unit. In 91% of the patients' samples d-dimer levels were elevated, in some patients up to several hundredfold as compared to normal values. The highest mean d-dimer values were present in the patient group with thromboembolic diseases, and particularly in non-survivors of pulmonary embolism. In patients with circulatory impairment (r=0.794) and in patients with infections (r=0.487) a statistically significant correlation was present between d-dimer levels and the APACHE II score (P<0.001). The logistic organ dysfunction score (LOD, P<0.001) correlated with d-dimer levels only in patients with circulatory impairment (r=0.474). On the contrary, patients without circulatory impairment demonstrated no correlation of d-dimer levels to the APACHE II or LOD score. Taking all patients together, no correlations of d-dimer levels with single organ failure or with indicators of infection could be detected. In conclusion, d-dimer plasma levels strongly correlated with the severity of the disease and organ dysfunction in patients with circulatory impairment or infections suggesting that elevated d-dimer levels may reflect the extent of microcirculatory failure. Thus, a therapeutic strategy to improve the microcirculation in such patients may be monitored using d-dimer plasma levels.

  20. Examples of data processing systems. Data processing system for JT-60

    International Nuclear Information System (INIS)

    Aoyagi, Tetsuo

    1996-01-01

    JT-60 data processing system is a large computer complex system including a lot of micro-computers, several mini-computers, and a main-frame computer. As general introduction of the original system configuration has been published previously, some improvements are described here. Transient mass data storage system, network database server, a data acquisition system using engineering workstations, and a graphic terminal emulator for X-Window are presented. These new features are realized by utilizing recent progress in computer and network technology and carefully designed user interface specification of the original system. (author)

  1. Numerical simulation on current spike behaviour of JT-60U disruptive plasmas

    International Nuclear Information System (INIS)

    Takei, N; Nakamura, Y; Tsutsui, H; Yoshino, R; Kawano, Y; Ozeki, T; Tobita, K; Tsuji-Iio, S; Shimada, R; Jardin, S C

    2004-01-01

    Characteristics and underlying mechanisms for plasma current spikes, which have been frequently observed during the thermal quench of JT-60U disruptions, were investigated through tokamak simulation code simulations including the passive shell effects of the vacuum vessel. Positive shear and reversed shear (PS and RS) plasmas were shown to have various current spike features in the experiments, e.g. an impulsive increase in the plasma current (positive spike) in the majority of thermal quenches, and a sudden decrease (negative spike), that has been excluded from past consideration, as an exception. It was first clarified that the shell effects, which become significant especially at a strong pressure drop due to the thermal quench of high β p plasmas, play an important role in the current spike in accordance with the initial relation of the radial location between the plasma equilibria and the vacuum vessel. As a consequence, a negative current spike may appear at thermal quench when the plasma is positioned further out from the geometric centre of the vacuum vessel. It was also pointed out that a further lowering in the internal inductance, in contradiction to previous interpretation in the past, is a plausible candidate for the mechanism for positive current spikes observed even in RS plasmas. The new interpretation enables us to reason out the whole character of current spikes of JT-60U disruptions

  2. Analysis of Food Hub Commerce and Participation Using Agent-Based Modeling: Integrating Financial and Social Drivers.

    Science.gov (United States)

    Krejci, Caroline C; Stone, Richard T; Dorneich, Michael C; Gilbert, Stephen B

    2016-02-01

    Factors influencing long-term viability of an intermediated regional food supply network (food hub) were modeled using agent-based modeling techniques informed by interview data gathered from food hub participants. Previous analyses of food hub dynamics focused primarily on financial drivers rather than social factors and have not used mathematical models. Based on qualitative and quantitative data gathered from 22 customers and 11 vendors at a midwestern food hub, an agent-based model (ABM) was created with distinct consumer personas characterizing the range of consumer priorities. A comparison study determined if the ABM behaved differently than a model based on traditional economic assumptions. Further simulation studies assessed the effect of changes in parameters, such as producer reliability and the consumer profiles, on long-term food hub sustainability. The persona-based ABM model produced different and more resilient results than the more traditional way of modeling consumers. Reduced producer reliability significantly reduced trade; in some instances, a modest reduction in reliability threatened the sustainability of the system. Finally, a modest increase in price-driven consumers at the outset of the simulation quickly resulted in those consumers becoming a majority of the overall customer base. Results suggest that social factors, such as desire to support the community, can be more important than financial factors. An ABM of food hub dynamics, based on human factors data gathered from the field, can be a useful tool for policy decisions. Similar approaches can be used for modeling customer dynamics with other sustainable organizations. © 2015, Human Factors and Ergonomics Society.

  3. Steady-state exhaust of helium ash in the W-shaped divertor of JT-60U

    International Nuclear Information System (INIS)

    Sakasai, A.; Takenaga, H.; Hosogane, N.

    2001-01-01

    By injecting a neutral beam of 60 keV helium (He) atoms as central fueling of helium into the ELMy H-mode plasmas, helium exhaust has been studied in the W-shaped pumped divertor on JT-60U. Efficient He exhaust was realized by He pumping using argon frosted cryopumps in the JT-60U new divertor. In steady state, good He exhaust capability (τ He */τ E =4 and high enrichment factor, where τ He * is a global particle confinement time of helium and τ E is the energy confinement time) was successfully demonstrated in attached ELMy H-mode plasmas. Good He exhaust capability was also obtained in detached ELMy H-mode plasmas, which was comparable to one in attached plasmas. This result of the helium exhaust is sufficient to support a detached divertor operation on ITER. After the divertor modification, helium exhaust in reversed shear plasmas has been investigated using He gas puff. Helium removal inside the internal transport barrier (ITB) is about two times as difficult as that outside the ITB in reversed shear discharges. (author)

  4. DAVINC3I: moving towards responsive hub network designs

    NARCIS (Netherlands)

    Ossevoort, R.; Keizer, de M.; Vorst, van der J.G.A.J.; Wenink, E.

    2013-01-01

    The Dutch floricultural sector is generally appreciated for its world leadership; the Netherlands is the flower trading hub for the European market. There are two trends affecting this position. First, virtualisation makes trade flows relatively footloose and flexible. Moreover, it enables the use

  5. Resistive instabilities in reversed shear discharges and wall stabilization on JT-60U

    International Nuclear Information System (INIS)

    Takeji, S.; Tokuda, S.; Fujita, T.; Suzuki, T.; Isayama, A.; Ide, S.; Ishii, Y.; Kamada, Y.; Koide, Y.; Matsumoto, T.; Oikawa, T.; Ozeki, T.; Sakamoto, Y.

    2001-01-01

    Resistive instabilities and wall stabilization of ideal low toroidal mode number, n, kink modes are investigated in JT-60U reversed shear discharges. Resistive interchange modes with n=1 are found to appear in reversed shear discharges with large pressure gradient at the normalized beta, β N , of about unity or even lower. The resistive interchange modes appear as intermittent burst-like magnetohydrodynamic (MHD) activities and higher n≤3 modes are observed occasionally in higher β N regime. No clear degradation of the plasma stored energy is observed by the resistive interchange modes themselves. It is also found that resistive interchange modes can lead to major collapse owing to a coupling with tearing modes at the outer mode rational surface over the minimum safety factor. Stability analysis revealed that stability parameter of tearing modes, Δ' , at the outer mode rational surface is affected by the free-boundary condition. The result is consistent with the experimental evidence that major collapse tends to occur when plasma edge safety factor, q*, is near integer values. Stabilization of ideal low n kink modes by the JT-60U wall is demonstrated. Magnetohydrodynamic perturbations that are attributed to resistive wall modes are observed followed by major collapse in wall-stabilized discharges. (author)

  6. Research dedusting efficiency of the inertial hub with adjustable parameters

    Directory of Open Access Journals (Sweden)

    Sharapov Rashid

    2016-01-01

    Full Text Available Production of construction materials every year production increases, thus increasing emissions pollutants into the atmosphere subjected to cleaning. At the enterprises of building materials production equipment becoming outdated both morally and physically exhausted their useful life. Technological design standards in the operation of purification equipment has undergone a number of changes. There are a large number of works devoted to the theory of cyclone separation. They examined calculation method and to determine the minimum size of particles is separated completely from the air stream in a cyclone. In theory, the high efficiency cyclones are relatively small separation of particles from the air stream. The experiments show that certain fractions of full capture occurs from the cyclones and out relatively large particles. Designed dust device hubs. They capture dust particles with low specific density and smaller than 5–10 microns. Rational use of hubs is achieved in the aspiration systems high performance. They are placed in front of or between the filter and the cyclone filter. Hub much reduces the amount of dust-laden air directed onto a thin cleaning. This reduces energy consumption for manufacturing as a whole, as well as, due to a possible decrease in performance fine filters, reducing their initial cost, metal consumption, maintenance costs and reduce the area occupied by them.

  7. Real-Time Monitoring and Fault Diagnosis of a Low Power Hub Motor Using Feedforward Neural Network

    Directory of Open Access Journals (Sweden)

    Mehmet Şimşir

    2016-01-01

    Full Text Available Low power hub motors are widely used in electromechanical systems such as electrical bicycles and solar vehicles due to their robustness and compact structure. Such systems driven by hub motors (in wheel motors encounter previously defined and undefined faults under operation. It may inevitably lead to the interruption of the electromechanical system operation; hence, economic losses take place at certain times. Therefore, in order to maintain system operation sustainability, the motor should be precisely monitored and the faults are diagnosed considering various significant motor parameters. In this study, the artificial feedforward backpropagation neural network approach is proposed to real-time monitor and diagnose the faults of the hub motor by measuring seven main system parameters. So as to construct a necessary model, we trained the model, using a data set consisting of 4160 samples where each has 7 parameters, by the MATLAB environment until the best model is obtained. The results are encouraging and meaningful for the specific motor and the developed model may be applicable to other types of hub motors. The prosperous model of the whole system was embedded into Arduino Due microcontroller card and the mobile real-time monitoring and fault diagnosis system prototype for hub motor was designed and manufactured.

  8. The influence of hubs in the structure of a neuronal network during an epileptic seizure

    Science.gov (United States)

    Rodrigues, Abner Cardoso; Cerdeira, Hilda A.; Machado, Birajara Soares

    2016-02-01

    In this work, we propose changes in the structure of a neuronal network with the intention to provoke strong synchronization to simulate episodes of epileptic seizure. Starting with a network of Izhikevich neurons we slowly increase the number of connections in selected nodes in a controlled way, to produce (or not) hubs. We study how these structures alter the synchronization on the spike firings interval, on individual neurons as well as on mean values, as a function of the concentration of connections for random and non-random (hubs) distribution. We also analyze how the post-ictal signal varies for the different distributions. We conclude that a network with hubs is more appropriate to represent an epileptic state.

  9. Edge pedestal characteristics in JET and JT-60U tokamaks under variable toroidal field ripple

    NARCIS (Netherlands)

    Urano, H.; Saibene, G.; Oyama, N.; Parail, V.; P. de Vries,; Sartori, R.; Kamada, Y.; Kamiya, K.; Loarte, A.; Lonnroth, J.; Sakamoto, Y.; Salmi, A.; Shinohara, K.; Takenaga, H.; Yoshida, M.

    2011-01-01

    The effects of toroidal field (TF) ripple on the edge pedestal characteristics were examined in the TF ripple scan experiments at the plasma current I(p) of 1.1 MA in JET and JT-60U. The TF ripple amplitude delta(R) was defined as a value averaged over the existing ripple wells at the separatrix on

  10. Reference design of the power supply system for the resistive-wall-mode control in JT-60SA

    Energy Technology Data Exchange (ETDEWEB)

    Ferro, Alberto, E-mail: alberto.ferro@igi.cnr.it [Consorzio RFX, C.so Stati Uniti 4, 35127 Padova (Italy); Gaio, Elena [Consorzio RFX, C.so Stati Uniti 4, 35127 Padova (Italy); Novello, Luca [Fusion for Energy, Broader Development of Fusion Department, Boltzmannstr 2, 85748 Garching (Germany); Matsukawa, Makoto; Shimada, Katsuhiro; Kawamata, Yoichi; Takechi, Manabu [Japan Atomic Energy Agency, Naka Fusion Institute, 801-1 Mukoyama, Naka, Ibaraki 311-019 (Japan)

    2015-10-15

    Highlights: • In JT-60SA, a power supply system (RWM-PS) will feed 18 coils to control the RWMs. • One power amplifier per coil will follow an arbitrary real-time reference. • Very fast dynamics is required (current bandwidth: 3 kHz; latency: 50 μs). • The requirements of the RWM-PS are updated and design solutions discussed. • The reference design of the RWM-PS is based on H-bridges operated at 20 – 30 kHz. - Abstract: The mission of JT-60SA, the satellite Tokamak under construction in Naka (Japan), includes the attainment of steady-state high-beta plasmas. For this purpose, an active control system based on 18 in-vessel sector coils (SC) is foreseen to suppress the resistive wall modes (RWM). Each coil will be independently fed by a dedicated converter, rated for 300 A and 240 V, which has to produce the required current/voltage following in real time the reference provided by the JT-60SA MHD Controller. To minimize the current rating, these converters shall be sufficiently fast to avoid an excessive growth of the RWM. This requires a very high dynamic performance, largely beyond that of standard industrial applications. This paper firstly reports the latest results of the studies on the requirements of the RWM active control system. Then, the reference design of the power supply system is presented, including the ac/dc conversion stage, the fast converters and the control section. The advantages of the proposed scheme are discussed and the main electrical parameters are presented.

  11. High Beta Steady State Research and Future Directions on JT-60U and JFT-2M

    Science.gov (United States)

    Ishida, Shinichi

    2003-10-01

    JT-60U and JFT-2M research is focused on high beta steady state operation towards economically and environmentally attractive reactors. In JT-60U, a high-βp H-mode plasma was sustained with βN 2.7 for 7.4 s in which neoclassical tearing modes (NTMs) limited the attainable β_N. Real-time tracking NTM stabilization system using ECCD demonstrated complete suppression of NTM leading to recovery of βN before onset of NTM. Performance in a fully non-inductive H-mode plasma was improved up to n_i(0) τE T_i(0) = 3.1 x 10^20 keV s m-3 using N-NBCD with βN 2.4, HH_y,2=1.2 and bootstrap fraction f_BS 0.5. ECH experiments extended the confinement enhancement for dominantly electron heated reversed shear plasmas up to HH_y,2 2 at T_e/Ti 1.25. A world record ECCD efficiency, 4.2 x 10^18 A/W/m^2, was achieved at Te 23 keV with a highly localized central current density. Innovative initiation and current build-up without center solenoid currents were established by LHCD/ECH and bootstrap current up to f_BS 0.9. In JFT-2M, the inside of the vacuum vessel wall was fully covered with low-activation ferritic steel plates to investigate their use in plasmas near fusion conditions. High βN plasmas were produced up to βN = 3.3 with an internal transport barrier (ITB) and a steady H-mode edge. A new H-mode regime with steady high recycling (HRS) and an ITB was exploited leading to βN H_89P 6.2 at n_e/nG 0.7. In 2003, JT-60U will be able to operate for the duration up to 65 s at 1 MA/2.7 T and the heating/current-drive duration up to 30 s at 17 MW to prolong high-βN and/or high-f_BS discharges with feedback controls. JFT-2M is planning to implement wall stabilization experiments in 2004 to pursue plasmas above the ideal no-wall limit using a ferritic wall. The modification of JT-60 to a fully superconducting tokamak is under discussion to explore high-β steady state operation in collision-less plasmas well above no-wall limit with ferritic wall in a steady state.

  12. Development of the piezoelectric gas injection valve for JT-60

    International Nuclear Information System (INIS)

    Kawasaki, Kazuo; Hiratuka, Hajime

    1986-01-01

    Piezoelectric gas injection valve (PEV) for JT-60 have been developed which was a piezo-electric element. The raliability of the PEV under the actual condition of high magnetic fields and high temperatures are veryfied, and it became clear that the PEV had enough throughput range and sufficient repetability for long life throughput characteristics. Remarkables of the developed PEV are summarized as follows, (1) The maximum throughput rate, responce time and helium leakage rate satisfy the desiged specifications. (2) Throughput equation for PEV is clarified by comparison with experiment. (3) Reliabilities of PEV under the actual condition during coil power test become clear. (author)

  13. CH-47D Rotating System Fault Sensing for Condition Based Maintenance

    Science.gov (United States)

    2011-03-01

    aircraft. 8 Figure 2.3: CH-47D Rotor Trim Tab [10] Several methods are utilized to prevent this imbalance. Mechanical dampers filled with a viscous and...pressurized fluid , commonly referred to as lag dampers , link the rotor blades to the rotor hub and attempt to minimize this out-of-balance condition...and requires the use of a flap bearing. This flap bearing and the lag damper are both potential sources of vibration if they are not performing to

  14. The development of gas hubs in Europe

    International Nuclear Information System (INIS)

    Miriello, Caterina; Polo, Michele

    2015-01-01

    This paper investigates the development of wholesale markets for natural gas at the different stages of market liberalization. We identify three steps in the process: wholesale trade initially develops to cope with balancing needs when the shippers and suppliers segments become more fragmented; once the market becomes more liquid, it turns out to be a second source of gas procurement in alternative to long term contracts; finally, to manage price risk financial instruments are traded. We review in detail the different regulatory measures that must be introduced to create an efficient and functioning wholesale gas market. Finally, we analyze the evolution of gas hubs in the UK, the Netherlands, Germany and Italy in terms of market rules and market liquidity. We argue that each of these country cases can be easily located into the evolutionary path we have highlighted at the beginning, with the UK and the Netherlands leading the process, Germany and Italy constrained by limited supply; Italy is also showing an interesting counterfactual. -- Highlights: •The paper illustrates development paths for natural gas hubs in Europe. •Wholesale trade increases with competition. •The regulatory settings of UK, Netherlands, Germany and Italy are reviewed. •Each country is located into the evolutionary path highlighted in the analytical framework

  15. Optimal integrated sizing and planning of hubs with midsize/large CHP units considering reliability of supply

    International Nuclear Information System (INIS)

    Moradi, Saeed; Ghaffarpour, Reza; Ranjbar, Ali Mohammad; Mozaffari, Babak

    2017-01-01

    Highlights: • New hub planning formulation is proposed to exploit assets of midsize/large CHPs. • Linearization approaches are proposed for two-variable nonlinear CHP fuel function. • Efficient operation of addressed CHPs & hub devices at contingencies are considered. • Reliability-embedded integrated planning & sizing is formulated as one single MILP. • Noticeable results for costs & reliability-embedded planning due to mid/large CHPs. - Abstract: Use of multi-carrier energy systems and the energy hub concept has recently been a widespread trend worldwide. However, most of the related researches specialize in CHP systems with constant electricity/heat ratios and linear operating characteristics. In this paper, integrated energy hub planning and sizing is developed for the energy systems with mid-scale and large-scale CHP units, by taking their wide operating range into consideration. The proposed formulation is aimed at taking the best use of the beneficial degrees of freedom associated with these units for decreasing total costs and increasing reliability. High-accuracy piecewise linearization techniques with approximation errors of about 1% are introduced for the nonlinear two-dimensional CHP input-output function, making it possible to successfully integrate the CHP sizing. Efficient operation of CHP and the hub at contingencies is extracted via a new formulation, which is developed to be incorporated to the planning and sizing problem. Optimal operation, planning, sizing and contingency operation of hub components are integrated and formulated as a single comprehensive MILP problem. Results on a case study with midsize CHPs reveal a 33% reduction in total costs, and it is demonstrated that the proposed formulation ceases the need for additional components/capacities for increasing reliability of supply.

  16. Virtual Replication of IoT Hubs in the Cloud: A Flexible Approach to Smart Object Management

    Directory of Open Access Journals (Sweden)

    Simone Cirani

    2018-03-01

    Full Text Available In future years, the Internet of Things is expected to interconnect billions of highly heterogeneous devices, denoted as “smart objects”, enabling the development of innovative distributed applications. Smart objects are constrained sensor/actuator-equipped devices, in terms of computational power and available memory. In order to cope with the diverse physical connectivity technologies of smart objects, the Internet Protocol is foreseen as the common “language” for full interoperability and as a unifying factor for integration with the Internet. Large-scale platforms for interconnected devices are required to effectively manage resources provided by smart objects. In this work, we present a novel architecture for the management of large numbers of resources in a scalable, seamless, and secure way. The proposed architecture is based on a network element, denoted as IoT Hub, placed at the border of the constrained network, which implements the following functions: service discovery; border router; HTTP/Constrained Application Protocol (CoAP and CoAP/CoAP proxy; cache; and resource directory. In order to protect smart objects (which cannot, because of their constrained nature, serve a large number of concurrent requests and the IoT Hub (which serves as a gateway to the constrained network, we introduce the concept of virtual IoT Hub replica: a Cloud-based “entity” replicating all the functions of a physical IoT Hub, which external clients will query to access resources. IoT Hub replicas are constantly synchronized with the physical IoT Hub through a low-overhead protocol based on Message Queue Telemetry Transport (MQTT. An experimental evaluation, proving the feasibility and advantages of the proposed architecture, is presented.

  17. Abnormal intrinsic functional hubs in alcohol dependence: evidence from a voxelwise degree centrality analysis

    Directory of Open Access Journals (Sweden)

    Luo X

    2017-07-01

    Full Text Available Xiaoping Luo,1,2 Linghong Guo,1 Xi-Jian Dai,3 Qinglai Wang,2 Wenzhong Zhu,2 Xinjun Miao,2 Honghan Gong1 1Department of Radiology, The First Affiliated Hospital of Nanchang University, Nangchang, Jiangxi, People’s Republic of China; 2Department of Radiology, Wenzhou Chinese Medicine Hospital, Wenzhou, Zhejiang, People’s Republic of China; 3Department of Medical Imaging, Jinling Hospital, Medical School of Nanjing University, Nanjing, Jiangsu, People’s Republic of China Objective: To explore the abnormal intrinsic functional hubs in alcohol dependence using voxelwise degree centrality analysis approach, and their relationships with clinical features.Materials and methods: Twenty-four male alcohol dependence subjects free of medicine (mean age, 50.21±9.62 years and 24 age- and education-matched male healthy controls (mean age, 50.29±8.92 years were recruited. The alcohol use disorders identification test and the severity of alcohol dependence questionnaire (SADQ were administered to assess the severity of alcohol craving. Voxelwise degree centrality approach was used to assess the abnormal intrinsic functional hubs features in alcohol dependence. Simple linear regression analysis was performed to investigate the relationships between the clinical features and abnormal intrinsic functional hubs.Results: Compared with healthy controls, alcohol dependence subjects exhibited significantly different degree centrality values in widespread left lateralization brain areas, including higher degree centrality values in the left precentral gyrus (BA 6, right hippocampus (BA 35, 36, and left orbitofrontal cortex (BA 11 and lower degree centrality values in the left cerebellum posterior lobe, bilateral secondary visual network (BA 18, and left precuneus (BA 7, 19. SADQ revealed a negative linear correlation with the degree centrality value in the left precentral gyrus (R2=0.296, P=0.006.Conclusion: The specific abnormal intrinsic functional hubs appear

  18. Modelling river bank erosion processes and mass failure mechanisms using 2-D depth averaged numerical model

    Science.gov (United States)

    Die Moran, Andres; El kadi Abderrezzak, Kamal; Tassi, Pablo; Herouvet, Jean-Michel

    2014-05-01

    Bank erosion is a key process that may cause a large number of economic and environmental problems (e.g. land loss, damage to structures and aquatic habitat). Stream bank erosion (toe erosion and mass failure) represents an important form of channel morphology changes and a significant source of sediment. With the advances made in computational techniques, two-dimensional (2-D) numerical models have become valuable tools for investigating flow and sediment transport in open channels at large temporal and spatial scales. However, the implementation of mass failure process in 2D numerical models is still a challenging task. In this paper, a simple, innovative algorithm is implemented in the Telemac-Mascaret modeling platform to handle bank failure: failure occurs whether the actual slope of one given bed element is higher than the internal friction angle. The unstable bed elements are rotated around an appropriate axis, ensuring mass conservation. Mass failure of a bank due to slope instability is applied at the end of each sediment transport evolution iteration, once the bed evolution due to bed load (and/or suspended load) has been computed, but before the global sediment mass balance is verified. This bank failure algorithm is successfully tested using two laboratory experimental cases. Then, bank failure in a 1:40 scale physical model of the Rhine River composed of non-uniform material is simulated. The main features of the bank erosion and failure are correctly reproduced in the numerical simulations, namely the mass wasting at the bank toe, followed by failure at the bank head, and subsequent transport of the mobilised material in an aggradation front. Volumes of eroded material obtained are of the same order of magnitude as the volumes measured during the laboratory tests.

  19. An improved method for predicting the effects of flight on jet mixing noise

    Science.gov (United States)

    Stone, J. R.

    1979-01-01

    A method for predicting the effects of flight on jet mixing noise has been developed on the basis of the jet noise theory of Ffowcs-Williams (1963) and data derived from model-jet/free-jet simulated flight tests. Predicted and experimental values are compared for the J85 turbojet engine on the Bertin Aerotrain, the low-bypass refanned JT8D engine on a DC-9, and the high-bypass JT9D engine on a DC-10. Over the jet velocity range from 280 to 680 m/sec, the predictions show a standard deviation of 1.5 dB.

  20. Optimal Scheduling of a Multi-Carrier Energy Hub Supplemented By Battery Energy Storage Systems

    DEFF Research Database (Denmark)

    Javadi, Mohammad Sadegh; Anvari-Moghaddam, Amjad; Guerrero, Josep M.

    2017-01-01

    This paper introduces a management model for optimal scheduling of a multi-carrier energy hub. In the proposed hub, three types of assets are considered: dispersed generating systems (DGs) such as micro-combined heat and power (mCHP) units, storage devices such as battery-based electrical storage...... systems (ESSs), and heating/cooling devices such as electrical heater, heat-pumps and absorption chillers. The optimal scheduling and management of the examined energy hub assets in line with electrical transactions with distribution network is modeled as a mixed-integer non-linear optimization problem....... In this regard, optimal operating points of DG units as well as ESSs are calculated based on a cost-effective strategy. Degradation cost of ESSs is also taken into consideration for short-term scheduling. Simulation results demonstrate that including well-planned energy storage options together with optimal...