Novel two-phase jet impingement heat sink for active cooling of electronic devices

International Nuclear Information System (INIS)

Oliveira, Pablo A. de; Barbosa, Jader R.

2017-01-01

Highlights: • Novel jet-based heat sink integrates the evaporator and the expansion device. • The system was tested with a small-scale oil-free R-134a compressor. • The thermodynamic performance of the cooling system was evaluated experimentally. • The single-jet maximum cooling capacity was 160 W, with a COP of 2.3 and a η 2nd of 8%. • Maximum heat transfer coefficient of 15 kW m −2 K −1 and surface temperature of 30 °C. - Abstract: This work presents a compact vapor compression cooling system equipped with a small-scale oil-free R-134a compressor and a jet-impingement-based heat sink that integrates the evaporator and the expansion device into a single unit. At the present stage of the development, a single orifice was used to generate the high-speed two-phase impinging jet on the heated surface. The effects of the compressor piston stroke, applied thermal load and orifice diameter on the system performance were quantified. The thermodynamic performance of the system was evaluated in terms of the temperature of the heated surface, impinging jet heat transfer coefficient, several system thermal resistances, coefficient of performance, second-law efficiency and second-law ratio. The coefficient of performance of the new refrigeration system increased with the cooling capacity, justifying its application in the removal of large thermal loads. The maximum system cooling capacity with a single jet was approximately 160 W, which was achieved with an orifice diameter of 500 μm and operation at a full compressor piston stroke. This condition corresponded to a COP of 2.3, a second-law efficiency of 8.0%, a jet impingement heat transfer coefficient above 15 kW m −2 K −1 and a heater surface temperature of approximately 30 °C.

Gas-Jet Meniscus Control in Ribbon Growth

Science.gov (United States)

Zoutendyk, J. A.; Vonroos, O.

1983-01-01

Gas jet used to control shape of meniscus and thus to regulate ribbon thickness in vertical silicon-ribbon growth. Gas jet also cools ribbon, increasing maximum possible pull speed for silicon, contact angle of 11 degrees plus or minus 1 degree required for constant thickness ribbon growth. Cooling effect of gas jet increases maximum possible pull speed.

Shock and vibration protection of submerged jet impingement cooling systems: Theory and experiment

International Nuclear Information System (INIS)

Haji Hosseinloo, Ashkan; Tan, Siow Pin; Yap, Fook Fah; Toh, Kok Chuan

2014-01-01

In the recent years, advances in high power density electronics and computing systems have pushed towards more advanced thermal management technologies and higher-capacity cooling systems. Among different types of cooling systems, jet impingement technology has gained attention and been widely used in different industries for its adaptability, cooling uniformity, large heat capacity, and ease of its localization. However, these cooling systems may not function properly in dynamically harsh environment inherent in many applications such as land, sea and air transportation. In this research article, a novel double-chamber jet impingement cooling system is fabricated and its performance is studied in harsh environment. Using the authors' previous studies, isolators with optimum properties are selected to ruggedize the chassis containing the cooling chamber against shock and random vibration. Experiments are conducted on both hard-mounted and isolated chassis and the cooling performance of the system is assessed using the inlet, and impingement surface temperatures of the cooling chamber. The experimental results show the isolation system prevents any failure that otherwise would occur, and also does not compromise the thermal performance of the system. - Highlights: • A novel double-chamber jet impingement cooling system was designed and fabricated. • Comprehensive set of random vibration and shock tests are conducted. • The isolation system proved to protect the cooling system properly against mechanical failure. • Cooling system performance was not significantly affected by the input random vibration and shock

The Use of Compressed Air for Micro-Jet Cooling After MIG Welding

Directory of Open Access Journals (Sweden)

Hadryś D.

2016-09-01

Full Text Available The material selected for this investigation was low alloy steel weld metal deposit (WMD after MIG welding with micro-jet cooling. The present investigation was aimed as the following tasks: obtained WMD with various amount of acicular ferrite and further analyze impact toughness of WMD in terms of acicular ferrite amount in it. Weld metal deposit (WMD was first time carried out for MIG welding with micro-jet cooling of compressed air and gas mixture of argon and air. Until that moment only argon, helium and nitrogen were tested as micro-jet gases for MIG/MAG processes. An important role in the interpretation of the results can give methods of artificial intelligence.

LASER WELDING WITH MICRO-JET COOLING FOR TRUCK FRAME WELDING

Directory of Open Access Journals (Sweden)

Jan PIWNIK

2017-12-01

Full Text Available The aim of this paper is to analyse the mechanical properties of the weld steel structure of car body truck frames after laser welding. The best welding conditions involve the use of proper materials and alloy elements in steel and filer materials, in addition to welding technology, state of stress and temperature of exploitation. We present for the first time the properties of steel track structures after laser welding with micro-jet cooling. Therefore, good selection of both welding parameters and micro-jet cooling parameters is very important to achieve a proper steel structure. In this study, the metallographic structure, tensile results and impact toughness of welded joints have been analysed in terms of welding parameters.

Experimental study of cooling performance of pneumatic synthetic jet with singular slot rectangular orifice

Science.gov (United States)

Yu, Roger Ho Zhen; Ismail, Mohd Azmi bin; Ramdan, Muhammad Iftishah; Mustaffa, Nur Musfirah binti

2017-03-01

Synthetic Jet generates turbulence flow in cooling the microelectronic devices. In this paper, the experiment investigation of the cooling performance of pneumatic synthetic jet with single slot rectangular orifices at low frequency motion is presented. The velocity profile at the end of the orifice was measured and used as characteristic performance of synthetic jet in the present study. Frequencies of synthetic jet and the compressed air pressure supplied to the pneumatic cylinder (1bar to 5bar) were the parameters of the flow measurement. The air velocity of the synthetic jet was measured by using anemometer air flow meter. The maximum air velocity was 0.5 m/s and it occurred at frequency motion of 8 Hz. The optimum compressed air supplied pressure of the synthetic jet study was 4 bar. The cooling performance of synthetic jet at several driven frequencies from 0 Hz to 8 Hz and heat dissipation between 2.5W and 9W were also investigate in the present study. The results showed that the Nusselt number increased and thermal resistance decreased with both frequency and Reynolds number. The lowest thermal resistance was 5.25°C/W and the highest Nusselt number was 13.39 at heat dissipation of 9W and driven frequency of 8Hz.

A model for radiative cooling of a semitransparent molten glass jet

International Nuclear Information System (INIS)

Song, M.; Ball, K.S.; Bergman, T.L.

1998-01-01

Transfer of molten glass from location to location typically involves a pouring process, during which a stream of glass is driven by gravity and cooled by combined convective and radiative heat transfer. This study of the thermal and fluid mechanics aspects of glass pouring is motivated by the glass casting of vitrified, surplus weapons-grade plutonium. Here, a mathematical model for the radiative cooling of a semitransparent molten glass jet with temperature-dependent viscosity has been developed and is implemented numerically. The axial velocity and jet diameter variations along the length of the jet, the axial bulk mean temperature distributions, and the centerline-to-surface glass temperature distributions are determined for different processing conditions. Comparisons are also made between the semitransparent predictions, which are based on a spectral discrete ordinates model, and predictions for an opaque medium

CPV cells cooling system based on submerged jet impingement: CFD modeling and experimental validation

Science.gov (United States)

Montorfano, Davide; Gaetano, Antonio; Barbato, Maurizio C.; Ambrosetti, Gianluca; Pedretti, Andrea

2014-09-01

Concentrating photovoltaic (CPV) cells offer higher efficiencies with regard to the PV ones and allow to strongly reduce the overall solar cell area. However, to operate correctly and exploit their advantages, their temperature has to be kept low and as uniform as possible and the cooling circuit pressure drops need to be limited. In this work an impingement water jet cooling system specifically designed for an industrial HCPV receiver is studied. Through the literature and by means of accurate computational fluid dynamics (CFD) simulations, the nozzle to plate distance, the number of jets and the nozzle pitch, i.e. the distance between adjacent jets, were optimized. Afterwards, extensive experimental tests were performed to validate pressure drops and cooling power simulation results.

Liquid jet impingement cooling with diamond substrates for extremely high heat flux applications

International Nuclear Information System (INIS)

Lienhard V, J.H.

1993-01-01

The combination of impinging jets and diamond substrates may provide an effective solution to a class of extremely high heat flux problems in which very localized heat loads must be removed. Some potential applications include the cooling of high-heat-load components in synchrotron x-ray, fusion, and semiconductor laser systems. Impinging liquid jets are a very effective vehicle for removing high heat fluxes. The liquid supply arrangement is relatively simple, and low thermal resistances can be routinely achieved. A jet's cooling ability is a strong function of the size of the cooled area relative to the jet diameter. For relatively large area targets, the critical heat fluxes can approach 20 W/mm 2 . In this situation, burnout usually originates at the outer edge of the cooled region as increasing heat flux inhibits the liquid supply. Limitations from liquid supply are minimized when heating is restricted to the jet stagnation zone. The high stagnation pressure and high velocity gradients appear to suppress critical flux phenomena, and fluxes of up to 400 W/mm 2 have been reached without evidence of burnout. Instead, the restrictions on heat flux are closely related to properties of the cooled target. Target properties become an issue owing to the large temperatures and large temperature gradients that accompany heat fluxes over 100 W/mm 2 . These conditions necessitate a target with both high thermal conductivity to prevent excessive temperatures and good mechanical properties to prevent mechanical failures. Recent developments in synthetic diamond technology present a possible solution to some of the solid-side constraints on heat flux. Polycrystalline diamond foils can now be produced by chemical vapor deposition in reasonable quantity and at reasonable cost. Synthetic single crystal diamonds as large as 1 cm 2 are also available

Formation of Cool and Warm Jets by Magnetic Flux Emerging from the Solar Chromosphere to Transition Region

Science.gov (United States)

Yang, Liping; Peter, Hardi; He, Jiansen; Tu, Chuanyi; Wang, Linghua; Zhang, Lei; Yan, Limei

2018-01-01

In the solar atmosphere, jets are ubiquitous at various spatial-temporal scales. They are important for understanding the energy and mass transports in the solar atmosphere. According to recent observational studies, the high-speed network jets are likely to be intermittent but continual sources of mass and energy for the solar wind. Here, we conduct a 2D magnetohydrodynamics simulation to investigate the mechanism of these network jets. A combination of magnetic flux emergence and horizontal advection is used to drive the magnetic reconnection in the transition region between a strong magnetic loop and a background open flux. The simulation results show that not only a fast warm jet, much similar to the network jets, is found, but also an adjacent slow cool jet, mostly like classical spicules, is launched. Differing from the fast warm jet driven by magnetic reconnection, the slow cool jet is mainly accelerated by gradients of both thermal pressure and magnetic pressure near the outer border of the mass-concentrated region compressed by the emerging loop. These results provide a different perspective on our understanding of the formation of both the slow cool jets from the solar chromosphere and the fast warm jets from the solar transition region.

Safety analysis of water cooled components inside the JET thermonuclear fusion tokamak

International Nuclear Information System (INIS)

Ageladarakis, P.; O'Dowd, N.; Papastergiou, S.

1998-04-01

The transient thermal behaviour of a number of components, installed in the vessel of the world's largest Fusion Tokamak (JET) has been examined with a theoretical model, which simulated normal operational conditions and abnormal scenarios namely: Loss of Coolant Flow; Loss of Torus Vacuum; and combinations. A number of theoretical results related to water and cryogenically cooled devices have been validated by a comprehensive experimental campaign conducted both inside the JET plasma chamber and in a test rig. The performance of water cooled components which may be subjected to boiling or freeze-up risks in case of a Loss of Water Flow event has also been analysed. Time constants of transient temperature changes were determined by the model while protective actions were prescribed in order to safeguard the equipment against associated risks. A completely automatic safety protection system has been designed on the basis of these analyses and implemented in the routine JET operation. During operation of JET the safety code reacted several times within the specified time limits and protected the relevant components during real off-normal events. (author)

Performance Analysis of a Multiple Micro-Jet Impingements Cooling Model

Directory of Open Access Journals (Sweden)

A. Husain

2016-06-01

Full Text Available The present study investigates the thermal performance of a multiple micro-jet impingements model for electronics cooling. The fluid flow and heat transport characteristics were investigated for steady incompressible laminar flow by solving three-dimensional (3D Navier-Stokes equations. Several parallel and staggered micro-jet configurations (ie. inline 2 Å~ 2, 3 Å~ 3 and 4 Å~ 4 jets, and staggered five-jet and 13-jet arrays with the jet diameter to the channel height ratios from 0.25–0.5 were analyzed at various flow rates for the maximum temperature rise, pressure drop, heat-transfer coefficient, thermal resistance, and pumping power characteristics. The parametric investigation was carried out based on the number of jets and the jet diameters at various mass flow rates and jet Reynolds numbers. Temperature uniformity and coefficient of performance were evaluated to find out the trade-off among the various designs investigated in the present study. The maximum temperature rise and the pressure drop decreased with an increase in the number of jets except in the case of staggered five-jet array. A higher temperature uniformity was observed at higher flow rates with a decrease in the coefficient of performance. The performance parameters, such as thermal resistance and pumping power, showed a conflicting nature with respect to design variables (viz. jet diameter to stand-off ratio and interjet spacing or number of jets at various Reynolds numbers within the laminar regime.

CAUSE AND EFFECT OF FEEDBACK: MULTIPHASE GAS IN CLUSTER CORES HEATED BY AGN JETS

International Nuclear Information System (INIS)

Gaspari, M.; Ruszkowski, M.; Sharma, P.

2012-01-01

Multiwavelength data indicate that the X-ray-emitting plasma in the cores of galaxy clusters is not cooling catastrophically. To a large extent, cooling is offset by heating due to active galactic nuclei (AGNs) via jets. The cool-core clusters, with cooler/denser plasmas, show multiphase gas and signs of some cooling in their cores. These observations suggest that the cool core is locally thermally unstable while maintaining global thermal equilibrium. Using high-resolution, three-dimensional simulations we study the formation of multiphase gas in cluster cores heated by collimated bipolar AGN jets. Our key conclusion is that spatially extended multiphase filaments form only when the instantaneous ratio of the thermal instability and free-fall timescales (t TI /t ff ) falls below a critical threshold of ≈10. When this happens, dense cold gas decouples from the hot intracluster medium (ICM) phase and generates inhomogeneous and spatially extended Hα filaments. These cold gas clumps and filaments 'rain' down onto the central regions of the core, forming a cold rotating torus and in part feeding the supermassive black hole. Consequently, the self-regulated feedback enhances AGN heating and the core returns to a higher entropy level with t TI /t ff > 10. Eventually, the core reaches quasi-stable global thermal equilibrium, and cold filaments condense out of the hot ICM whenever t TI /t ff ∼< 10. This occurs despite the fact that the energy from AGN jets is supplied to the core in a highly anisotropic fashion. The effective spatial redistribution of heat is enabled in part by the turbulent motions in the wake of freely falling cold filaments. Increased AGN activity can locally reverse the cold gas flow, launching cold filamentary gas away from the cluster center. Our criterion for the condensation of spatially extended cold gas is in agreement with observations and previous idealized simulations.

Should catastrophic risks be included in a regulated competitive health insurance market?

Science.gov (United States)

van de Ven, W P; Schut, F T

1994-11-01

In 1988 the Dutch government launched a proposal for a national health insurance based on regulated competition. The mandatory benefits package should be offered by competing insurers and should cover both non-catastrophic risks (like hospital care, physician services and drugs) and catastrophic risks (like several forms of expensive long-term care). However, there are two arguments to exclude some of the catastrophic risks from the competitive insurance market, at least during the implementation process of the reforms. Firstly, the prospects for a workable system of risk-adjusted payments to the insurers that should take away the incentives for cream skimming are, at least during the next 5 years, more favorable for the non-catastrophic risks than for the catastrophic risks. Secondly, even if a workable system of risk-adjusted payments can be developed, the problem of quality skimping may be relevant for some of the catastrophic risks, but not for non-catastrophic risks. By 'quality skimping' we mean the reduction of the quality of care to a level which is below the minimum level that is acceptable to society. After 5 years of health care reforms in the Netherlands new insights have resulted in a growing support to confine the implementation of the reforms to the non-catastrophic risks. In drawing (and redrawing) the exact boundaries between different regulatory regimes for catastrophic and non-catastrophic risks, the expected benefits of a cost-effective substitution of care have to be weighted against the potential harm caused by cream skimming and quality skimping.

Impact Load of Welds After Micro-Jet Cooling / Dynamiczne Obciążenie Spoin Chłodzonych Mikrojetowo

Directory of Open Access Journals (Sweden)

Hadryś D.

2015-12-01

Full Text Available Micro-jet cooling is an innovative method of forced cooling. It could be used to cooling after welding immediately. It allows to obtain welds with better properties in comparison to ordinary welding method. Favourable structure of weld metal deposit (WMD with higher content of acicular ferrite (AF could be obtained. These properties can be controlled by several variables (e. g. type of cooling gas, number of jets. Plastic properties are particularly important in case of impact load. This type of strength is very dangerous for the structure and for safety of users (ex. car body during car crash. This article presents the influence of the cooling gas and the number of jets on plastic properties of the weld joint for impact load. It is described by restitution coefficient and plastic strain.

Numerical modeling and validation of helium jet impingement cooling of high heat flux divertor components

International Nuclear Information System (INIS)

Koncar, Bostjan; Simonovski, Igor; Norajitra, Prachai

2009-01-01

Numerical analyses of jet impingement cooling presented in this paper were performed as a part of helium-cooled divertor studies for post-ITER generation of fusion reactors. The cooling ability of divertor cooled by multiple helium jets was analysed. Thermal-hydraulic characteristics and temperature distributions in the solid structures were predicted for the reference geometry of one cooling finger. To assess numerical errors, different meshes (hexagonal, tetra, tetra-prism) and discretisation schemes were used. The temperatures in the solid structures decrease with finer mesh and higher order discretisation and converge towards finite values. Numerical simulations were validated against high heat flux experiments, performed at Efremov Institute, St. Petersburg. The predicted design parameters show reasonable agreement with measured data. The calculated maximum thimble temperature was below the tile-thimble brazing temperature, indicating good heat removal capability of reference divertor design. (author)

Emergency cooling system with hot-water jet pumps for nuclear reactors

International Nuclear Information System (INIS)

Reinsch, A.O.W.

1977-01-01

The ECCS for a PWR or BWR uses hot-water jet pumps to remove the thermal energy generated in the reactor vessel and stored in the water. The hot water expands in the nozzle part (Laval nozzle) of the jet pump and sucks in coolant (borated water) coming from a storage tank containing subcooled water. This water is mixing with the hot water/steam mixture from the Laval nozzle. The steam is condensed. The kinetic energy of the water is converted into a pressure increase which is sufficient to feed the water into the reactor vessel. The emergency cooling may further be helped by a jet condenser also operating according to the principle of a jet pump and condensing the steam generated in the reactor vessel. (DG) [de

Analysis of Heat Transfer in Cooling of a Hot Plate by Planar Impingement Jet

International Nuclear Information System (INIS)

Ahn, Dae Hwan; Kim, Dong Sik

2009-01-01

Water jet impingement cooling is used to remove heat from high-temperature surfaces such as hot steel plates in the steel manufacturing process (thermo-mechanical cooling process; TMCP). In those processes, uniform cooling is the most critical factor to ensure high strength steel and good quality. In this study, experiments are performed to measure the heat transfer coefficient together with the inverse heat conduction problem (IHCP) analysis for a plate cooled by planar water jet. In the inverse heat transfer analysis, spatial and temporal variations of heat transfer coefficient, with no information regarding its functional form, are determined by employing the conjugate gradient method with an adjoint problem. To estimate the two dimensional distribution of heat transfer coefficient and heat flux for planar waterjet cooling, eight thermo-couple are installed inside the plate. The results show that heat transfer coefficient is approximately uniform in the span-wise direction in the early stage of cooling. In the later stage where the forced-convection effect is important, the heat transfer coefficient becomes larger in the edge region. The surface temperature vs. heat flux characteristics are also investigated for the entire boiling regimes. In addition, the heat transfer rate for the two different plate geometries are compared at the same Reynolds number

Computational parametric study of an impinging jet in a cross-flow configuration for electronics cooling applications

International Nuclear Information System (INIS)

Larraona, Gorka S.; Rivas, Alejandro; Antón, Raúl; Ramos, Juan Carlos; Pastor, Ignacio; Moshfegh, Bahram

2013-01-01

A parametric study based on design of experiments (DoE) techniques was carried out by computational simulation in order to evaluate the effect that design parameters have on heat transfer and pressure loss of an impinging jet in a cross-flow configuration. The main effects of each parameter and the interactions between parameters were analyzed in detail through the Response Surface Methodology (RSM). Additionally, the potential of the impinging jet in a cross-flow configuration was assessed by calculating the optimal values of the parameters and comparing the cooling efficiency of the resulting configuration with the efficiency of the conventional cross-flow configuration. It was found that the degree to which the average heat transfer coefficient is enhanced as the result of adding an impinging jet depends on the height of the cooled component. Specifically, it was found that the higher the component, the more significant the enhancement. -- Highlights: ► Five design parameters of an impinging jet in a cross-flow (IJCF) have been considered. ► Channel and jet velocities are found to be the most influential parameters. ► Significant interactions exist between some of the parameters. ► Larger cooling efficiency is achieved with the IJCF compared to the cross-flow solely. ► The enhancement obtained with the IJCF depends on the height of the component

Coefficient of restitution and plastic strain for impact of elements welded with micro-jet cooling

Directory of Open Access Journals (Sweden)

Damian HADRYŚ

2014-06-01

Full Text Available The main purpose of investigations is the qualification how post-accident repair of model car body parts influence on the value of coefficient of restitution. Evaluation of impact energy absorption by model car body parts repaired with MIG welding (with and without micro-jet cooling was carried out. The results of investigations present that the value of coefficient of restitution changes with speed of impact. Coefficient of restitution is bigger for elements welded with micro-jet cooling than for element welded with ordinary method. This could have influence on passive safety of vehicle.

Cause and Effect of Feedback: Multiphase Gas in Cluster Cores Heated by AGN Jets

Science.gov (United States)

Gaspari, M.; Ruszkowski, M.; Sharma, P.

2012-02-01

Multiwavelength data indicate that the X-ray-emitting plasma in the cores of galaxy clusters is not cooling catastrophically. To a large extent, cooling is offset by heating due to active galactic nuclei (AGNs) via jets. The cool-core clusters, with cooler/denser plasmas, show multiphase gas and signs of some cooling in their cores. These observations suggest that the cool core is locally thermally unstable while maintaining global thermal equilibrium. Using high-resolution, three-dimensional simulations we study the formation of multiphase gas in cluster cores heated by collimated bipolar AGN jets. Our key conclusion is that spatially extended multiphase filaments form only when the instantaneous ratio of the thermal instability and free-fall timescales (t TI/t ff) falls below a critical threshold of ≈10. When this happens, dense cold gas decouples from the hot intracluster medium (ICM) phase and generates inhomogeneous and spatially extended Hα filaments. These cold gas clumps and filaments "rain" down onto the central regions of the core, forming a cold rotating torus and in part feeding the supermassive black hole. Consequently, the self-regulated feedback enhances AGN heating and the core returns to a higher entropy level with t TI/t ff > 10. Eventually, the core reaches quasi-stable global thermal equilibrium, and cold filaments condense out of the hot ICM whenever t TI/t ff fashion. The effective spatial redistribution of heat is enabled in part by the turbulent motions in the wake of freely falling cold filaments. Increased AGN activity can locally reverse the cold gas flow, launching cold filamentary gas away from the cluster center. Our criterion for the condensation of spatially extended cold gas is in agreement with observations and previous idealized simulations.

Effects of geometry on slot-jet film cooling performance

Energy Technology Data Exchange (ETDEWEB)

Hyams, D.G.; McGovern, K.T.; Leylek, J.H. [Clemson Univ., SC (United States)

1995-10-01

The physics of the film cooling process for shaped, inclined slot-jets with realistic slot-length-to-width ratios (L/s) is studied for a range of blowing ratio (M) and density ratio (DR) parameters typical of gas turbine operations. For the first time in the open literature, the effect of inlet and exit shaping of the slot-jet on both flow and thermal field characteristics is isolated, and the dominant mechanisms responsible for differences in these characteristics are documented. A previously documented computational methodology was applied for the study of four distinct configurations: (1) slot with straight edges and sharp corners (reference case); (2) slot with shaped inlet region; (3) slot with shaped exit region; and (4) slot with both shaped inlet and exit regions. Detailed field results as well as surface phenomena involving adiabatic film effectiveness ({eta}) and heat transfer coefficient (h) are presented. It is demonstrated that both {eta} and h results are vital in the proper assessment of film cooling performance. All simulations were carried out using a multi-block, unstructured/adaptive grid, fully explicit, time-marching solver with multi-grid, local time stepping, and residual smoothing type acceleration techniques. Special attention was paid to and full documentation provided for: (1) proper modeling of the physical phenomena; (2) exact geometry and high quality grid generation techniques; (3) discretization schemes; and (4) turbulence modeling issues. The key parameters M and DR were varied from 1.0 to 2.0 and 1.5 to 2.0, respectively, to show their influence. Simulations were repeated for slot length-to-width ratio (L/s) of 3.0 and 4.5 in order to explain the effects of this important parameter. Additionally, the performance of two popular turbulence models, standard k-F, and RNG k-E, were studied to establish their ability to handle highly elliptic jet/crossflow interaction type processes.

Should catastrophic risks be included in a regulated competitive health insurance market?

NARCIS (Netherlands)

W.P.M.M. van de Ven (Wynand); F.T. Schut (Erik)

1994-01-01

textabstractIn 1988 the Dutch government launched a proposal for a national health insurance based on regulated competition. The mandatory benefits package should be offered by competing insurers and should cover both non-catastrophic risks (like hospital care, physician services and drugs) and

Effect of jet nozzle geometry on flow and heat transfer performance of vortex cooling for gas turbine blade leading edge

International Nuclear Information System (INIS)

Du, Changhe; Li, Liang; Wu, Xin; Feng, Zhenping

2016-01-01

Highlights: • We establish a suitable vortex chamber model for gas turbine blade leading edge. • Mechanism of vortex cooling is further discussed and presented. • Influences of jet nozzle geometry on vortex cooling characteristics are researched. • This paper focuses on assessment of flow field and thermal performance for different jet nozzle aspect ratio and area. - Abstract: In this paper, 3D viscous steady Reynolds Averaged Navier–Stokes (RANS) equations are utilized to investigate the influence of jet nozzle geometry on flow and thermal behavior of vortex cooling for gas turbine blades. Comparison between calculation with different turbulence models and the experimental data is conducted, and results show that the standard k-ω model provides the best accuracy. The grid independence analysis is performed to obtain the proper mesh number. First, the mechanism of vortex cooling is further discussed, and the pronounced impact of kinetic turbulence intensity, thin thermal boundary layer, violent radial convection and complex vortices on enhanced heat transfer performance is confirmed. Then, seven jet nozzle aspect ratios and seven jet nozzle to chamber cross section area ratios are selected to research the flow field and thermal characteristics of vortex cooling focusing on the streamline, static pressure ratio, total pressure loss ratio and Nusselt number. It is presented that the jet nozzle aspect ratio and jet nozzle to chamber cross section area ratio both impose a significant effect on the flow and thermal parameters. The averaged Nusselt number decreases at first and then increases with the increasing jet nozzle aspect ratio, reaching highest when aspect ratio equals to 1. The effect of area ratio on averaged Nusselt number is complex. Finally, the heat transfer results in this study are compared with other previous works. Results indicate that good agreement with previous data is achieved, and the enhanced thermal behavior may be acquired by

Compressive Strength of Steel Frames after Welding with Micro-Jet Cooling

Directory of Open Access Journals (Sweden)

Hadryś D.

2016-03-01

Full Text Available Low carbon steel weld structures generally exhibit a very linear stress-strain relationship. In the study of strength of materials, the compressive strength is the capacity of a material or structure to withstand loads tending to reduce size of structure. It is mainly measured by plotting applied force against deformation in a testing machine. Compressive strength is a main key value for design of welded structures.The main goal of that paper was analysing of plastic properties of frame welds which were made with various parameters of micro-jet cooling. New technology of micro-jet welding could be regarded as a new way to improve plastic properties of welds. It allows to obtain welds with better mechanical properties in comparison to ordinary welding method. Furthermore it is possible to steering of weld structure and properties of the weld. There were given main information about influence of various micro-jet gases on metallographic and properties of structure steel welds.

Toward Cooling Uniformity: Investigation of Spiral, Sweeping Holes, and Unconventional Cooling Paradigms

Science.gov (United States)

Shyam, Vikram; Thurman, Douglas R.; Poinsatte, Philip E.; Ameri, Ali A.; Culley, Dennis E.

2018-01-01

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. Ways to quantify the efficacy of novel cooling holes that are asymmetric, not uniformly spaced or that show variation from hole to hole are presented. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and square holes. A patent-pending spiral hole design showed the highest potential of the nondiffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing ratios of 1.0, 1.5, 2.0, and 2.5 at a density ratio of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS. A section on ideas for future work is included that addresses issues of quantifying cooling uniformity and provides some ideas for changing the way we think about cooling such as changing the direction of cooling or coupling acoustic devices to cooling holes to regulate frequency.

LASER WELDING WITH MICRO-JET COOLING FOR TRUCK FRAME WELDING

OpenAIRE

Jan PIWNIK; Bożena SZCZUCKA-LASOTA; Tomasz WĘGRZYN; Wojciech MAJEWSKI

2017-01-01

The aim of this paper is to analyse the mechanical properties of the weld steel structure of car body truck frames after laser welding. The best welding conditions involve the use of proper materials and alloy elements in steel and filer materials, in addition to welding technology, state of stress and temperature of exploitation. We present for the first time the properties of steel track structures after laser welding with micro-jet cooling. Therefore, good selection of both welding paramet...

Single-jet gas cooling of in-beam foils or specimens: Prediction of the convective heat-transfer coefficient

Science.gov (United States)

Steyn, Gideon; Vermeulen, Christiaan

2018-05-01

An experiment was designed to study the effect of the jet direction on convective heat-transfer coefficients in single-jet gas cooling of a small heated surface, such as typically induced by an accelerated ion beam on a thin foil or specimen. The hot spot was provided using a small electrically heated plate. Heat-transfer calculations were performed using simple empirical methods based on dimensional analysis as well as by means of an advanced computational fluid dynamics (CFD) code. The results provide an explanation for the observed turbulent cooling of a double-foil, Havar beam window with fast-flowing helium, located on a target station for radionuclide production with a 66 MeV proton beam at a cyclotron facility.

Two-colour dip spectroscopy of jet-cooled molecules

Science.gov (United States)

Ito, Mitsuo

In optical-optical double resonance spectroscopy, the resonance transition from an intermediate state to a final state can be detected by a dip of the signal (fluorescence or ion) associated with the intermediate state. This method probing the signal of the intermediate state may be called `two-colour dip spectroscopy'. Various kinds of two-colour dip spectroscopy such as two-colour fluorescence/ion dip spectroscopy, two-colour ionization dip spectroscopy employing stimulated emission, population labelling spectroscopy and mass-selected ion dip spectroscopy with dissociation were briefly described, paying special attention to their characteristics in excitation, detection and application. They were extensively and successfully applied to jet-cooled large molecules and provided us with new useful information on the energy and dynamics of excited molecules.

Experimental Flow Performance Evaluation of novel miniaturized Advanced Piezoelectric Dual Cooling Jet

International Nuclear Information System (INIS)

De Bock, H P J; Whalen, B P; Chamarthy, P; Jackson, J L

2012-01-01

In recent years, electronics systems have significantly reduced in size at maintained or increased functionality. This trend has led to an increased demand for smaller and more capable thermal management. However, miniaturization of conventional fan and heat sink cooling systems introduce significant size, weight and efficiency challenges. In this study the flow performance of a novel alternative thin form-factor cooling solution, the advanced piezoelectric dual cooling jet(DCJ), is evaluated. A DCJ is a system where two piezoelectric actuators are excited to produce air flow. The total height of the device is about 1mm. The design of the experimental method for evaluating the equivalent fan-curve of the DCJ device is described in detail. Experimental results in comparison to conventional fan solutions are provided. The DCJ is expected to be a good candidate for thermal management in next generation thin profile consumer electronics.

Modular jet impingement assemblies with passive and active flow control for electronics cooling

Energy Technology Data Exchange (ETDEWEB)

Zhou, Feng; Dede, Ercan Mehmet; Joshi, Shailesh

2016-09-13

Power electronics modules having modular jet impingement assembly utilized to cool heat generating devices are disclosed. The modular jet impingement assemblies include a modular manifold having a distribution recess, one or more angled inlet connection tubes positioned at an inlet end of the modular manifold that fluidly couple the inlet tube to the distribution recess and one or more outlet connection tubes positioned at an outlet end of the modular manifold that fluidly coupling the outlet tube to the distribution recess. The modular jet impingement assemblies include a manifold insert removably positioned within the distribution recess and include one or more inlet branch channels each including an impinging slot and one or more outlet branch channels each including a collecting slot. Further a heat transfer plate coupled to the modular manifold, the heat transfer plate comprising an impingement surface including an array of fins that extend toward the manifold insert.

Emergency core cooling system

International Nuclear Information System (INIS)

Arai, Kenji; Oikawa, Hirohide.

1990-01-01

The device according to this invention can ensure cooling water required for emerency core cooling upon emergence such as abnormally, for example, loss of coolant accident, without using dynamic equipments such as a centrifugal pump or large-scaled tank. The device comprises a pressure accumulation tank containing a high pressure nitrogen gas and cooling water inside, a condensate storage tank, a pressure suppression pool and a jet stream pump. In this device there are disposed a pipeline for guiding cooling water in the pressure accumulation tank as a jetting water to a jetting stream pump, a pipeline for guiding cooling water stored in the condensate storage tank and the pressure suppression pool as pumped water to the jetting pump and, further, a pipeline for guiding the discharged water from the jet stream pump which is a mixed stream of pumped water and jetting water into the reactor pressure vessel. In this constitution, a sufficient amount of water ranging from relatively high pressure to low pressure can be supplied into the reactor pressure vessel, without increasing the size of the pressure accumulation tank. (I.S.)

Shaft Wear After Surfacing with Micro-Jet Cooling / Zużycie Ścierne Wałów Po Napawaniu Z Chłodzeniem Mikro-Strugowym

Directory of Open Access Journals (Sweden)

Węgrzyn T.

2015-12-01

Full Text Available A paper presents a piece of information about innovate surfacing technology with micro-jet cooling. There are put down information about parameters of shaft surfacing with micro-jet cooling process. There were given information about influence of various micro-jet gases on metallographic structure of machine shaft after surfacing. There were analyzed tribological properties of welds. Welding surfacing process is very often used to apply a hardness or wear-resistant layer of base metal. It is very important method of extending the life of machines, tools, and construction equipment. Surfacing is also known as wearfacing, is often used to build up shafts, gears or cutting edges. Regenerated surface properties of various machine elements do not provide good tribological properties. The tribological interactions of a solid shaft surfaces were tested after welding with micro-jet cooling.

Catastrophic cooling and cessation of heating in the solar corona

Science.gov (United States)

Peter, H.; Bingert, S.; Kamio, S.

2012-01-01

Context. Condensations in the more than 106 K hot corona of the Sun are commonly observed in the extreme ultraviolet (EUV). While their contribution to the total solar EUV radiation is still a matter of debate, these condensations certainly provide a valuable tool for studying the dynamic response of the corona to the heating processes. Aims: We investigate different distributions of energy input in time and space to investigate which process is most relevant for understanding these coronal condensations. Methods: For a comparison to observations we synthesize EUV emission from a time-dependent, one-dimensional model for coronal loops, where we employ two heating scenarios: simply shutting down the heating and a model where the heating is very concentrated at the loop footpoints, while keeping the total heat input constant. Results: The heating off/on model does not lead to significant EUV count rates that one observes with SDO/AIA. In contrast, the concentration of the heating near the footpoints leads to thermal non-equilibrium near the loop top resulting in the well-known catastrophic cooling. This process gives a good match to observations of coronal condensations. Conclusions: This shows that the corona needs a steady supply of energy to support the coronal plasma, even during coronal condensations. Otherwise the corona would drain very fast, too fast to even form a condensation. Movies are available in electronic form at http://www.aanda.org

Selected Parameters of Micro-Jet Cooling Gases in Hybrid Spraying Process

Directory of Open Access Journals (Sweden)

Szczucka-Lasota B.

2016-06-01

Full Text Available The innovative technology, like thermal spraying with a micro-jet cooling is one of the important modification of classical ultrasonic spraying methods. Using of micro-stream with gases like argon or nitrogen allows to cool the coating immediately after spraying, and thereby reduce the time of transition during the injection of each layer. As a result of the process, the fine dispersive structure of coatings is obtained during the shorter time in comparable to the classical high velocity oxygen fuel process (HVOF. The parameter of process and the type of stream equipment determine the quality of the obtained structure and thermal stress in the coating. The article presents the relationship between selected parameters of hybrid process and properties of the coatings. The presented technology should be adapted to the actual production of protective coating for machines and construction working in wear conditions.

Replication Catastrophe

DEFF Research Database (Denmark)

Toledo, Luis; Neelsen, Kai John; Lukas, Jiri

2017-01-01

Proliferating cells rely on the so-called DNA replication checkpoint to ensure orderly completion of genome duplication, and its malfunction may lead to catastrophic genome disruption, including unscheduled firing of replication origins, stalling and collapse of replication forks, massive DNA...... breakage, and, ultimately, cell death. Despite many years of intensive research into the molecular underpinnings of the eukaryotic replication checkpoint, the mechanisms underlying the dismal consequences of its failure remain enigmatic. A recent development offers a unifying model in which the replication...... checkpoint guards against global exhaustion of rate-limiting replication regulators. Here we discuss how such a mechanism can prevent catastrophic genome disruption and suggest how to harness this knowledge to advance therapeutic strategies to eliminate cancer cells that inherently proliferate under...

System and method for regulating EGR cooling using a rankine cycle

Science.gov (United States)

Ernst, Timothy C.; Morris, Dave

2015-12-22

This disclosure relates to a waste heat recovery (WHR) system and method for regulating exhaust gas recirculation (EGR) cooling, and more particularly, to a Rankine cycle WHR system and method, including a recuperator bypass arrangement to regulate EGR exhaust gas cooling for engine efficiency improvement and thermal management. This disclosure describes other unique bypass arrangements for increased flexibility in the ability to regulate EGR exhaust gas cooling.

Experimental investigation of cross-over jets in a rib-roughened trailing-edge cooling channel

Science.gov (United States)

Xue, Fei

Increasing the rotor inlet temperature can dramatically increase the efficiency and power output of the gas turbine engine. However, the melting point of turbine blade material limits the realistic upper bound of the rotor inlet temperature. As a result, the development of high temperature turbine blade material and advanced turbine blade cooling technology determines the future of turbine blade engine. Adding impingement jet holes and rib turbulators in the inner cooling channel of the gas turbine blades are two effective ways to enhance the cooling effects. The purpose of this study is to figure out the influence of different combinations of jet holes and rib turbulators on the heat transfer efficiency. A tabletop scale test model is used in the study to simulate the cooling cavity of trailing edge and its feed channel in a real gas turbine blade. The Dimensional Analysis Theory is used in the study to eliminate the influence of scaling. Two different crossover slots are tested with 5 different rib arrangements, and each of the test geometries is tested for 6 jet Reynolds numbers ranging from 10,000 to 36,000. The two different crossover slots are the crossover slots with 0 and 5 degree tilt angles. The four different rib arrangements are ribs with 0 degree, 45 degree, 90 degree and 135 degree angles of attack with respect to the flow direction. Furthermore, a smooth test section (no ribs) was also tested. The steady state liquid crystal thermography is used to quantify the heat transfer performance of the target areas. The variation of Nusselt number versus Reynolds number is plotted for each of the 10 geometries. Also, the variation of Nusselt number versus Reynolds number are compared for different rib angles of attack with the same crossover slot tilt angle, and between different crossover slots tilt angles with the same rib angle. The results show that, the area-weighted average Nusselt number increases monotonically with the Reynolds number; the target

Numerical simulation of flow characteristics of lean jet to cross-flow in safety injection of reactor cooling system

International Nuclear Information System (INIS)

Wang Haijun; He Huining; Luo Yushan; Wang Weishu

2011-01-01

In the present work, a numerical simulation was performed to study the flow characteristics of lean jet to cross flow in a main tube in the safety injection of reactor cooling system. The influence scope and mixing characteristics of the confined lean jet in cross-flow were studied. It can be concluded that three basic flow regimes are marked, namely the attached lean jet, lift-off lean jet and impinging lean jet. The velocity ratio V R is the key factor in the flow state. The depth and region of jet to main flow are enhanced with the increase of the velocity ratio. The jet flow penetrates through the main flow with the increase of the velocity ratio. At higher velocity ratio, the jet flow strikes the main flow bottom and circumfluence happens in upriver of main flow. The vortex flow characteristics dominate the flow near region of jet to cross-flow and the mixture of jet to cross-flow. At different velocity ratio V R , the vortex grows from the same displacement, but the vortex type and the vortex is different. At higher velocity ratio, the vortex develops fleetly, wears off sharp and dies out sharp. The study is very important to the heat transfer experiments of cross-flow jet and thermal stress analysis in the designs of nuclear engineering. (authors)

Two-phase jet impingement cooling for high heat flux wide band-gap devices using multi-scale porous surfaces

International Nuclear Information System (INIS)

Joshi, Shailesh N.; Dede, Ercan M.

2017-01-01

Highlights: • Jet impingement with phase change on multi-scale porous surfaces is investigated. • Porous coated flat, pin-fin, open tunnel, and closed tunnel structures are studied. • Boiling curve, heat transfer coefficient, and pressure drop metrics are reported. • Flow visualization shows vapor removal from the surface is a key aspect of design. • The porous coated pin-fin surface exhibits superior two-phase cooling performance. - Abstract: In the future, wide band-gap (WBG) devices such as silicon carbide and gallium nitride will be widely used in automotive power electronics due to performance advantages over silicon-based devices. The high heat fluxes dissipated by WBG devices pose extreme cooling challenges that demand the use of advanced thermal management technologies such as two-phase cooling. In this light, we describe the performance of a submerged two-phase jet impingement cooler in combination with porous coated heat spreaders and multi-jet orifices. The cooling performance of four different porous coated structures was evaluated using R-245fa as the coolant at sub-cooling of 5 K. The results show that the boiling performance of a pin-fin heat spreader is the highest followed by that for an open tunnel (OPT), closed tunnel (CLT), and flat heat spreader. Furthermore, the flat heat spreader demonstrated the lowest critical heat flux (CHF), while the pin-fin surface sustained a heat flux of 218 W/cm 2 without reaching CHF. The CHF values of the OPT and CLT surfaces were 202 W/cm 2 and 194 W/cm 2 , respectively. The pin-fin heat spreader has the highest two-phase heat transfer coefficient of 97,800 W/m 2 K, while the CLT surface has the lowest heat transfer coefficient of 69,300 W/m 2 K, both at a heat flux of 165 W/cm 2 . The variation of the pressure drop of all surfaces is similar for the entire range of heat fluxes tested. The flat heat spreader exhibited the least pressure drop, 1.73 kPa, while the CLT surface had the highest, 2.17 kPa at a

Large Eddy Simulation of a cooling impinging jet to a turbulent crossflow

Science.gov (United States)

Georgiou, Michail; Papalexandris, Miltiadis

2015-11-01

In this talk we report on Large Eddy Simulations of a cooling impinging jet to a turbulent channel flow. The impinging jet enters the turbulent stream in an oblique direction. This type of flow is relevant to the so-called ``Pressurized Thermal Shock'' phenomenon that can occur in pressurized water reactors. First we elaborate on issues related to the set-up of the simulations of the flow of interest such as, imposition of turbulent inflows, choice of subgrid-scale model and others. Also, the issue of the commutator error due to the anisotropy of the spatial cut-off filter induced by non-uniform grids is being discussed. In the second part of the talk we present results of our simulations. In particular, we focus on the high-shear and recirculation zones that are developed and on the characteristics of the temperature field. The budget for the mean kinetic energy of the resolved-scale turbulent velocity fluctuations is also discussed and analyzed. Financial support has been provided by Bel V, a subsidiary of the Federal Agency for Nuclear Control of Belgium.

ANISOTROPIC THERMAL CONDUCTION AND THE COOLING FLOW PROBLEM IN GALAXY CLUSTERS

International Nuclear Information System (INIS)

Parrish, Ian J.; Sharma, Prateek; Quataert, Eliot

2009-01-01

We examine the long-standing cooling flow problem in galaxy clusters with three-dimensional magnetohydrodynamics simulations of isolated clusters including radiative cooling and anisotropic thermal conduction along magnetic field lines. The central regions of the intracluster medium (ICM) can have cooling timescales of ∼200 Myr or shorter-in order to prevent a cooling catastrophe the ICM must be heated by some mechanism such as active galactic nucleus feedback or thermal conduction from the thermal reservoir at large radii. The cores of galaxy clusters are linearly unstable to the heat-flux-driven buoyancy instability (HBI), which significantly changes the thermodynamics of the cluster core. The HBI is a convective, buoyancy-driven instability that rearranges the magnetic field to be preferentially perpendicular to the temperature gradient. For a wide range of parameters, our simulations demonstrate that in the presence of the HBI, the effective radial thermal conductivity is reduced to ∼<10% of the full Spitzer conductivity. With this suppression of conductive heating, the cooling catastrophe occurs on a timescale comparable to the central cooling time of the cluster. Thermal conduction alone is thus unlikely to stabilize clusters with low central entropies and short central cooling timescales. High central entropy clusters have sufficiently long cooling times that conduction can help stave off the cooling catastrophe for cosmologically interesting timescales.

Comparison of central axis and jet ring coolant supply for turbine disk cooling on a SSME-HPOTP model

Science.gov (United States)

Kim, Y. W.; Metzger, D. E.

1992-01-01

The test facility, test methods and results are presented for an experimental study modeling the cooling of turbine disks in the blade attachment regions with multiple impinging jets, in a configuration simulating the disk cooling method employed on the Space Shuttle Main Engine oxygen turbopump. The study's objective was to provide a comparison of detailed local convection heat transfer rates obtained for a single center-supply of disk coolant with those obtained with the present flight configuration where disk coolant is supplied through an array of 19 jets located near the disk outer radius. Specially constructed disk models were used in a program designed to evaluate possible benefits and identify any possible detrimental effects involved in employing an alternate disk cooling scheme. The study involved the design, construction and testing of two full scale rotating model disks, one plane and smooth for baseline testing and the second contoured to the present flight configuration, together with the corresponding plane and contoured stator disks. Local heat transfer rates are determined from the color display of encapsulated liquid crystals coated on the disk in conjunction with use of a computer vision system. The test program was composed of a wide variety of disk speeds, flowrates, and geometrical configurations, including testing for the effects of disk boltheads and gas ingestion from the gas path region radially outboard of the disk-cavity.

The Effect Of Different Micro-Jet Streams Number On Plastic Properties Of Welds

Directory of Open Access Journals (Sweden)

Hadryś D.

2015-09-01

Full Text Available The main goal of that paper was analysing of plastic properties of welds made with micro-jet cooling. New technology of micro-jet welding could be regarded as a new way to improve plastic properties of welds. It allows to obtain welds with better properties in comparison to ordinary welding method. Moreover, it is possible to steering of weld structure and properties of the weld. During research Erichsen cupping tests and bending tests were carried out for welds made by MIG method with micro-jet cooling. Argon was cooling medium. Different numbers of micro-jet streams were used to weld cooling. Different plastic properties were obtained for different numbers of micro-jet streams. In this research welds made by new method of welding (welding with micro-jet cooling were compared with welds made by ordinary welding method.

Numerical Predictions of Enhanced Impingement Jet Cooling with Ribs and Pins in Co-Flow and Cross-Flow Configurations

Directory of Open Access Journals (Sweden)

A. M. El-Jummah

2017-02-01

Full Text Available Numerical calculations relevant to gas turbine internal wall heat transfer cooling were conducted using conjugate heat transfer (CHT computational Fluid Dynamics (CFD commercial codes. The CHT CFD predictions were carried out for impingement heat transfer with different types of obstacle walls (fins on the target surfaces. A 10 × 10 row of impingement air jet holes (or hole density n of 4306 m-2 was used, which gives ten rows of holes in the cross-flow direction and only one heat transfer enhancement obstacle per impingement jet was investigated. Previously, four different shaped obstacles were investigated experimentally and were used to validate the present predictions. The obstacle walls, which were equally spaced on the centreline between each impingement jet are of the co-flow and cross-flow configurations. The impingement jet pitch X to diameter D, X/D and gap Z to diameter, Z/D ratios were kept constant at 4.66 and 3.06 for X, Z and D of 15.24, 10.00 and 3.27 mm, respectively. The obstacles investigated were ribs and rectangular pin-fins shapes, using two obstacles height H to diameter, H/D ratio of 1.38 and 2.45. Computations were carried out for three different mass flux G of 1.08, 1.48 and 1.94 kg/sm2. Relative pressure loss ∆P/P and surface average heat transfer coefficient (HTC h predictions for the range of G, showed good agreement with the experimental results. The prediction also reveals that obstacles not only increases the turbulent flows, but also takes away most of the cooling heat transfer that produces the regions with highest thermal gradients. It also reduces the impingement gap downstream cross-flow.

High-resolution spectroscopy of jet-cooled CH{sub 5}{sup +}: Progress

Energy Technology Data Exchange (ETDEWEB)

Savage, C.; Dong, F.; Nesbitt, D. J. [JILA, University of Colorado and National Institute of Standards and Technology, and Department of Chemistry and Biochemistry, University of Colorado, Boulder, Colorado 80309-0440 (United States)

2015-01-22

Protonated methane (CH{sub 5}{sup +}) is thought to be a highly abundant molecular ion in interstellar medium, as well as a potentially bright μwave- mm wave emitter that could serve as a tracer for methane. This paper describes progress and first successful efforts to obtain a high resolution, supersonically cooled spectrum of CH{sub 5}{sup +} in the 2900-3100 cm{sup −1} region, formed in a slit supersonic discharge at low jet temperatures and with sub-Doppler resolution. Short term precision in frequency measurement (< 5 MHz on an hour time scale) is obtained from a thermally controlled optical transfer cavity servoloop locked onto a frequency stabilized HeNe laser. Long term precision (< 20 MHz day-to-day) due to pressure, temperature and humidity dependent index of refraction effects in the optical transfer cavity is also present and discussed.

Jet operated heat pump

International Nuclear Information System (INIS)

Collard, T.H.

1982-01-01

A jet pump system is shown that utilizes waste heat to provide heating and/or cooling. Waste heat diverted through a boiler causes a refrigerant to evaporate and expand for supersonic discharge through a nozzle thereby creating a vacuum in an evaporator coil. The vacuum draws the refrigerant in a gaseous state into a condensing section of a jet pump along with refrigerant from a reservoir in a subcooled liquid form. This causes condensation of the gas in a condensation section of the jet pump, while moving at constant velocity. The change in momentum of the fluid overcomes the system high side pressure. Some of the condensate is cooled by a subcooler. Refrigerant in a subcooled liquid state from the subcooler is fed back into the evaporator and the condensing section with an adequate supply being insured by the reservoir. The motive portion of the condensate is returned to the boiler sans subcooling. By proper valving start-up is insured, as well as the ability to switch from heating to cooling

Observation of vibronic emission spectrum of jet-cooled 3,5-difluorobenzyl radical.

Science.gov (United States)

Lee, Seung Woon; Yoon, Young Wook; Lee, Sang Kuk

2010-09-02

We applied the technique of corona-excited supersonic expansion using a pinhole-type glass nozzle to observe the vibronic emission spectrum of jet-cooled benzyl-type radicals from the corona discharge of precursor 3,5-difluorotoluene seeded in a large amount of inert helium carrier gas. The vibronically well-resolved emission spectrum was recorded with a long-path monochromator in the visible region. After subtracting the vibronic bands originating from isomeric difluorobenzyl radicals from the observed spectrum, we identified for the first time the bands belonging to the 3,5-difluorobenzyl radical, from which the electronic energy and vibrational mode frequencies of the 3,5-difluorobenzyl radical were accurately determined in the ground electronic state by comparison with those of the precursor and with those from an ab initio calculation.

Catastrophes control problem

International Nuclear Information System (INIS)

Velichenko, V.V.

1994-01-01

The problem of catastrophe control is discussed. Catastrophe control aims to withdraw responsible engineering constructions out of the catastrophe. The mathematical framework of catastrophes control systems is constructed. It determines the principles of systems filling by the concrete physical contents and, simultaneously, permits to employ modern control methods for the synthesis of optimal withdrawal strategy for protected objects

Observable Emission Features of Black Hole GRMHD Jets on Event Horizon Scales

Energy Technology Data Exchange (ETDEWEB)

Pu, Hung-Yi [Perimeter Institute for Theoretical Physics, 31 Caroline Street North, Waterloo, ON, N2L 2Y5 (Canada); Wu, Kinwah [Mullard Space Science Laboratory, University College London, Holmbury St. Mary, Dorking, Surrey, RH5 6NT (United Kingdom); Younsi, Ziri; Mizuno, Yosuke [Institut für Theoretische Physik, Max-von-Laue-Straße 1, D-60438 Frankfurt am Main (Germany); Asada, Keiichi; Nakamura, Masanori, E-mail: hpu@perimeterinstitute.ca, E-mail: asada@asiaa.sinica.edu.tw, E-mail: nakamura@asiaa.sinica.edu.tw, E-mail: kinwah.wu@ucl.ac.uk, E-mail: younsi@th.physik.uni-frankfurt.de, E-mail: mizuno@th.physik.uni-frankfurt.de [Institute of Astronomy and Astrophysics, Academia Sinica, 11F of Astronomy-Mathematics Building, AS/NTU No. 1, Taipei 10617, Taiwan (China)

2017-08-20

The general-relativistic magnetohydrodynamical (GRMHD) formulation for black hole-powered jets naturally gives rise to a stagnation surface, where inflows and outflows along magnetic field lines that thread the black hole event horizon originate. We derive a conservative formulation for the transport of energetic electrons, which are initially injected at the stagnation surface and subsequently transported along flow streamlines. With this formulation the energy spectra evolution of the electrons along the flow in the presence of radiative and adiabatic cooling is determined. For flows regulated by synchrotron radiative losses and adiabatic cooling, the effective radio emission region is found to be finite, and geometrically it is more extended along the jet central axis. Moreover, the emission from regions adjacent to the stagnation surface is expected to be the most luminous as this is where the freshly injected energetic electrons are concentrated. An observable stagnation surface is thus a strong prediction of the GRMHD jet model with the prescribed non-thermal electron injection. Future millimeter/submillimeter (mm/sub-mm) very-long-baseline interferometric observations of supermassive black hole candidates, such as the one at the center of M87, can verify this GRMHD jet model and its associated non-thermal electron injection mechanism.

Jet array impingement flow distributions and heat transfer characteristics. Effects of initial crossflow and nonuniform array geometry. [gas turbine engine component cooling

Science.gov (United States)

Florschuetz, L. W.; Metzger, D. E.; Su, C. C.; Isoda, Y.; Tseng, H. H.

1982-01-01

Two-dimensional arrays of circular air jets impinging on a heat transfer surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer surface. The configurations considered are intended to model those of interest in current and contemplated gas turbine airfoil midchord cooling applications. The effects of an initial crossflow which approaches the array through an upstream extension of the channel are considered. Flow distributions as well as heat transfer coefficients and adiabatic wall temperatures resolved to one streamwise hole spacing were measured as a function of the initial crossflow rate and temperature relative to the jet flow rate and temperature. Both Nusselt number profiles and dimensionless adiabatic wall temperature (effectiveness) profiles are presented and discussed. Special test results which show a significant reduction of jet orifice discharge coefficients owing to the effect of a confined crossflow are also presented, along with a flow distribution model which incorporates those effects. A nonuniform array flow distribution model is developed and validated.

Editorial on Future Jet Technologies

Science.gov (United States)

Gal-Or, Benjamin

2014-12-01

The jet engine is the prime flight controller in post-stall flight domains where conventional flight control fails, or when the engine prevents catastrophes in training, combat, loss of all airframe hydraulics (the engine retains its own hydraulics), loss of one engine, pilot errors, icing on the wings, landing gear and runway issues in takeoff and landing and in bad-whether recoveries. The scientific term for this revolutionary technology is "jet-steering", and in engineering practice - "thrust vectoring", or "TV". Jet-Steering in advanced fighter aircraft designs is integrated with stealth technology. The resulting classified Thrust-Vectoring-Stealth ("TVS") technology has generated a second jet-revolution by which all Air-&-Sea-Propulsion Science and R&D are now being reassessed. Classified F-22, X-47B/C and RQ-180 TVS-vehicles stand at the front of this revolution. But recent transfers of such sensitive technologies to South Korea and Japan [1-5], have raised various fundamental issues that are evaluated by this editorial-review. One, and perhaps a key conclusion presented here, means that both South Korea and Japan may have missed one of their air-&-sea defenses: To develop and field low-cost unmanned fleets of jet-drones, some for use with expensive, TVS-fighter aircraft in highly congested areas. In turn, the U.S., EU, Russia and China, are currently developing such fleets at various TVS levels and sizes. China, for instance, operates at least 15,000 drones ("UAVs") by 2014 in the civilian sector alone. All Chinese drones have been developed by at least 230 developers/manufacturers [1-16]. Mobile telecommunication of safe links between flyers and combat drones ("UCAVs") at increasingly deep penetrations into remote, congested areas, can gradually be purchased-developed-deployed and then operated by extant cader of tens of thousands "National Champion Flyers" who have already mastered the operation of mini-drones in free-to-all sport clubs under national

Single-phase liquid jet impingement heat transfer

International Nuclear Information System (INIS)

Webb, B.W.; Ma, C.F.

1995-01-01

Impinging liquid jets have been demonstrated to be an effective means of providing high heat/mass transfer rates in industrial transport processes. When a liquid jet strikes a surface, thin hydrodynamic and thermal boundary layers from in the region directly beneath due to the jet deceleration and the resulting increase in pressure. The flow is then forced to accelerate in a direction parallel to the target surface in what is termed the wall jet or parallel flow zone. The thickness of the hydrodynamic and thermal boundary layers in the stagnation region may be of the order of tens of micrometers. Consequently, very high heat/mass transfer coefficients exist in the stagnation zone directly under the jet. Transport coefficients characteristic of parallel flow prevail in the wall jet region. The high heat transfer coefficients make liquid jet impingement an attractive cooling option where high heat fluxes are the norm. Some industrial applications include the thermal treatment of metals, cooling of internal combustion engines, and more recently, thermal control of high-heat-dissipation electronic devices. Both circular and planar liquid jets have attracted research attention. 180 refs., 35 figs., 11 tabs

The possibility of using laser and micro-jet technology in the welding of structural elements of vehicles

OpenAIRE

Wojciech MAJEWSKI

2015-01-01

A paper presents the possibility of laser welding using micro-jet cooling. The effect of micro-jet cooling on microstructure and mechanical properties of the weld metal deposit was carried out. New welding process was analyzed for use in the automotive industry. Studies have confirmed the positive effect of cooling micro-jet cooling both for the MIG welding and laser welding.

Resonance Enhanced Multi-Photon Ionization and Uv-Uv Hole-Burning Spectroscopic Studies of Jet-Cooled Acetanilide Derivatives

Science.gov (United States)

Moon, Ceol Joo; Min, Ahreum; Ahn, Ahreum; Lee, Seung Jun; Choi, Myong Yong; Kim, Seong Keun

2013-06-01

Conformational investigations and photochemistry of jet-cooled methacetine (MA) and phenacetine (PA) using one color resonant two-photon ionization (REMPI), UV-UV hole-burning and IR-dip spectroscopy are presented. MA and PA are derivatives of acetanilide, substituted by methoxyl, ethoxyl group in the para position of acetanilide, respectively. Moreover, we have investigated conformational information of the acetanilide derivatives (AAP, MA and PA)-water. In this work, we will present and discuss the solvent effects of the hydroxyl group of acetanilide derivatives in the excited state.

The possibility of using laser and micro-jet technology in the welding of structural elements of vehicles

Directory of Open Access Journals (Sweden)

Wojciech MAJEWSKI

2015-12-01

Full Text Available A paper presents the possibility of laser welding using micro-jet cooling. The effect of micro-jet cooling on microstructure and mechanical properties of the weld metal deposit was carried out. New welding process was analyzed for use in the automotive industry. Studies have confirmed the positive effect of cooling micro-jet cooling both for the MIG welding and laser welding.

On sociological catastrophe analysis

International Nuclear Information System (INIS)

Clausen, L.

1974-01-01

The present paper deals with standard terms of sociological catastrophe theory hitherto existing, collective behaviour during the catastrophe, and consequences for the empiric catastrophe sociology. (RW) [de

Non-catastrophic and catastrophic fractures in racing Thoroughbreds at the Hong Kong Jockey Club.

Science.gov (United States)

Sun, T C; Riggs, C M; Cogger, N; Wright, J; Al-Alawneh, J I

2018-04-19

Reports of fractures in racehorses have predominantly focused on catastrophic injuries, and there is limited data identifying the location and incidence of fractures that did not result in a fatal outcome. To describe the nature and the incidence of non-catastrophic and catastrophic fractures in Thoroughbreds racing at the Hong Kong Jockey Club (HKJC) over seven racing seasons. Retrospective cohort study. Data of fractures sustained in horses while racing and of race characteristics were extracted from the HKJC Veterinary Management Information System (VMIS) and Racing Information System (RIS) respectively. The fracture event was determined from the first clinical entry for each specific injury. The incidence rates of non-catastrophic and catastrophic fractures were calculated per 1000 racing starts for racetrack, age, racing season, sex and trainer. 179 first fracture events occurred in 64,807 racing starts. The incidence rate of non-catastrophic fractures was 2.2 per 1000 racing starts and of catastrophic fractures was 0.6 per 1000 racing starts. Fractures of the proximal sesamoid bones represented 55% of all catastrophic fractures while the most common non-catastrophic fractures involved the carpus and the first phalanx. Significant associations were detected between the incidence of non-catastrophic fractures and sex, trainer and racing season. The first fracture event was used to calculate the incidence rate in this study and may have resulted in underestimation of the true incidence rate of fractures in this population. However, given the low number of recorded fracture events compared to the size of the study population, this underestimation is likely to be small. There were 3.6 times as many non-catastrophic fractures as catastrophic fractures in Thoroughbreds racing in Hong Kong between 2004 and 2011. Non-catastrophic fractures interfere with race training schedules and may predispose to catastrophic fracture. Future analytical studies on non-catastrophic

CSL protein regulates transcription of genes required to prevent catastrophic mitosis in fission yeast.

Science.gov (United States)

Převorovský, Martin; Oravcová, Martina; Zach, Róbert; Jordáková, Anna; Bähler, Jürg; Půta, František; Folk, Petr

2016-11-16

For every eukaryotic cell to grow and divide, intricately coordinated action of numerous proteins is required to ensure proper cell-cycle progression. The fission yeast Schizosaccharomyces pombe has been instrumental in elucidating the fundamental principles of cell-cycle control. Mutations in S. pombe 'cut' (cell untimely torn) genes cause failed coordination between cell and nuclear division, resulting in catastrophic mitosis. Deletion of cbf11, a fission yeast CSL transcription factor gene, triggers a 'cut' phenotype, but the precise role of Cbf11 in promoting mitotic fidelity is not known. We report that Cbf11 directly activates the transcription of the acetyl-coenzyme A carboxylase gene cut6, and the biotin uptake/biosynthesis genes vht1 and bio2, with the former 2 implicated in mitotic fidelity. Cbf11 binds to a canonical, metazoan-like CSL response element (GTGGGAA) in the cut6 promoter. Expression of Cbf11 target genes shows apparent oscillations during the cell cycle using temperature-sensitive cdc25-22 and cdc10-M17 block-release experiments, but not with other synchronization methods. The penetrance of catastrophic mitosis in cbf11 and cut6 mutants is nutrient-dependent. We also show that drastic decrease in biotin availability arrests cell proliferation but does not cause mitotic defects. Taken together, our results raise the possibility that CSL proteins play conserved roles in regulating cell-cycle progression, and they could guide experiments into mitotic CSL functions in mammals.

Catastrophizing Interferes with Cognitive Modulation of Pain in Women with Fibromyalgia.

Science.gov (United States)

Ellingson, Laura D; Stegner, Aaron J; Schwabacher, Isaac J; Lindheimer, Jacob B; Cook, Dane B

2018-02-21

Pain modulation is a critical function of the nociceptive system that includes the ability to engage descending pain control systems to maintain a functional balance between facilitation and inhibition of incoming sensory stimuli. Dysfunctional pain modulation is associated with increased risk for chronic pain and is characteristic of fibromyalgia (FM). Catastrophizing is also common in FM. However, its influence on pain modulation is poorly understood. To determine the role of catastrophizing on central nervous system processing during pain modulation in FM via examining brain responses and pain sensitivity during an attention-distraction paradigm. Twenty FM patients and 18 healthy controls (CO) underwent functional magnetic resonance imaging while receiving pain stimuli, administered alone and during distracting cognitive tasks. Pain ratings were assessed after each stimulus. Catastrophizing was assessed with the Pain Catastrophizing Scale (PCS). The ability to modulate pain during distraction varied among FM patients and was associated with catastrophizing. This was demonstrated by significant positive relationships between PCS scores and pain ratings (P modulation did not differ between FM and CO (P > 0.05). FM patients with higher levels of catastrophizing were less able to distract themselves from pain, indicative of catastrophizing-related impairments in pain modulation. These results suggest that the tendency to catastrophize interacts with attention-resource allocation and may represent a mechanism of chronic pain exacerbation and/or maintenance. Reducing catastrophizing may improve FM symptoms via improving central nervous system regulation of pain.

He-cooled divertor development for DEMO

International Nuclear Information System (INIS)

Norajitra, P.; Giniyatulin, R.; Ihli, T.; Janeschitz, G.; Krauss, W.; Kruessmann, R.; Kuznetsov, V.; Mazul, I.; Widak, V.; Ovchinnikov, I.; Ruprecht, R.; Zeep, B.

2007-01-01

Goal of the He-cooled divertor development for future fusion power plants is to resist a high heat flux of at least 10 MW/m 2 . The development includes the fields of design, analyses, and experiments. A helium-cooled modular jet concept (HEMJ) has been defined as reference solution, which is based on jet impingement cooling. In cooperation with the Efremov Institute, work was aimed at construction and high heat flux tests of prototypical tungsten mockups to demonstrate their manufacturability and their performances. A helium loop was built for this purpose to simulate the realistic thermo-hydraulics conditions close to those of DEMO (10 MPa He, 600 deg. C). The first high heat flux test results confirm the feasibility and the performance of the divertor design

Present and future JET ICRF antennae

International Nuclear Information System (INIS)

Kaye, A.; Brown, T.; Bhatnagar, V.; Crawley, P.; Jacquinot, J.; Lobel, R.; Plancoulaine, J.; Rebut, P.H.; Wade, T.; Walker, C.

1994-01-01

Since the initial operation of the JET ICRF system in 1985, up to 22 MW has been coupled to the plasma, many heating scenarios have been demonstrated and the main technological problem of RF-specific impurity production overcome. Many developments of the antennae have taken place over this period, notably the replacement of the water-cooled nickel screens with indirectly cooled beryllium screens, and the forthcoming installation of eight new A2 antennae for operation during the pumped divertor phase of JET. The A2 antennae include enhanced provision for fast wave current drive experiments on JET. This paper describes the beryllium screens, the technological results from operation and subsequent inspection of these screens, the design of the A2 antennae and the results from high power RF testing of a model of the A2 antenna. (orig.)

Applications of modelling historical catastrophic events with implications for catastrophe risk management

Science.gov (United States)

Sorby, A.; Grossi, P.; Pomonis, A.; Williams, C.; Nyst, M.; Onur, T.; Seneviratna, P.; Baca, A.

2009-04-01

The management of catastrophe risk is concerned with the quantification of financial losses, and their associated probabilities, for potential future catastrophes that might impact a region. Modelling of historical catastrophe events and, in particular, the potential consequences if a similar event were to occur at the present day can provide insight to help bridge the gap between what we know can happen from historical experience and what potential losses might be out there in the "universe" of potential catastrophes. The 1908 Messina Earthquake (and accompanying local tsunami) was one of the most destructive earthquakes to have occurred in Europe and by most accounts remains Europe's most fatal with over 70,000 casualties estimated. However, what would the potential consequences be, in terms of financial and human losses, if a similar earthquake were to occur at the present day? Exposures, building stock and populations can change over time and, therefore, the consequences of a similar earthquake at the present day may sensibly differ from those observed in 1908. The city of Messina has been reconstructed several times in its history, including following the 1908 earthquake and again following the Second World War. The 1908 earthquake prompted the introduction of the first seismic design regulations in Italy and since 1909 parts of the Messina and Calabria regions have been in the zones of highest seismic coefficient. Utilizing commercial catastrophe loss modelling technology - which combines the modelling of hazard, vulnerability, and financial losses on a database of property exposures - a modelled earthquake scenario of M7.2 in the Messina Straits region of Southern Italy is considered. This modelled earthquake is used to assess the potential consequences in terms of financial losses that an earthquake similar to the 1908 earthquake might have if it were to occur at the present day. Loss results are discussed in the context of applications for the financial

Seizing Catastrophes

DEFF Research Database (Denmark)

Kublitz, Anja

2013-01-01

to a distant past but takes place in the present. They use the term Nakba not only to refer to the catastrophe of 1948 but also to designate current catastrophes, such as the Danish Muhammad cartoons affair in 2005 and the Israeli invasion of Gaza in 2008. Through an analysis of the 60th commemoration...

Climate catastrophes

Science.gov (United States)

Budyko, Mikhail

1999-05-01

Climate catastrophes, which many times occurred in the geological past, caused the extinction of large or small populations of animals and plants. Changes in the terrestrial and marine biota caused by the catastrophic climate changes undoubtedly resulted in considerable fluctuations in global carbon cycle and atmospheric gas composition. Primarily, carbon dioxide and other greenhouse gas contents were affected. The study of these catastrophes allows a conclusion that climate system is very sensitive to relatively small changes in climate-forcing factors (transparency of the atmosphere, changes in large glaciations, etc.). It is important to take this conclusion into account while estimating the possible consequences of now occurring anthropogenic warming caused by the increase in greenhouse gas concentration in the atmosphere.

Direct catastrophic injury in sports.

Science.gov (United States)

Boden, Barry P

2005-11-01

Catastrophic sports injuries are rare but tragic events. Direct (traumatic) catastrophic injury results from participating in the skills of a sport, such as a collision in football. Football is associated with the greatest number of direct catastrophic injuries for all major team sports in the United States. Pole vaulting, gymnastics, ice hockey, and football have the highest incidence of direct catastrophic injuries for sports in which males participate. In most sports, the rate of catastrophic injury is higher at the collegiate than at the high school level. Cheerleading is associated with the highest number of direct catastrophic injuries for all sports in which females participate. Indirect (nontraumatic) injury is caused by systemic failure as a result of exertion while participating in a sport. Cardiovascular conditions, heat illness, exertional hyponatremia, and dehydration can cause indirect catastrophic injury. Understanding the common mechanisms of injury and prevention strategies for direct catastrophic injuries is critical in caring for athletes.

Saving Humanity from Catastrophic Cooling with Geo-Engineering

Science.gov (United States)

Haapala, K.; Singer, S. F.

2016-02-01

There are two kinds of ice ages; they are fundamentally different and therefore require different methods of mitigation: (i) Major (Milankovitch-style) glaciations occur on a 100,000-year time-scale and are controlled astronomically. (ii) "Little" ice ages were discovered in ice cores; they have been occurring on an approx. 1000-1500-yr cycle and are likely controlled by the Sun [Ref: Singer & Avery 2007. Unstoppable Global Warming: Every 1500 years]. The current cycle's cooling phase may be imminent - hence there may be urgent need for action. To stop onset of a major (Milankovitch) glaciation 1. Locate a "trigger" - a growing perennial snow/ice field - using satellites 2. Spread soot, to lower the albedo, and use Sun to melt 3. How much soot? How to apply soot? Learn by experimentation To lessen (regional, intermittent) cooling of DOB (Dansgaard-Oeschger-Bond) cycles1. Use greenhouse effect of manmade cirrus (ice particles) [Ref: Singer 1988. Meteorology and Atmospheric Physics 38:228 - 239]2. Inject water droplets (mist) near tropopause 3. Trace dispersion of cirrus cloud by satellite and observe warming at surface 4. How much water; over what area? How often to inject? Learn by experimentation Many scientific questions remain. While certainly interesting and important, there is really no need to delay the crucial and urgent tests of geo-engineering, designed to validate schemes of mitigation. Such proposed tests involve only minor costs and present negligible risks to the environment.

Experimental investigation of the influence of the air jet trajectory on convective heat transfer in buildings equipped with air-based and radiant cooling systems

DEFF Research Database (Denmark)

Le Dreau, Jerome; Heiselberg, Per; Jensen, Rasmus Lund

2015-01-01

-state and dynamic conditions. With the air-based cooling system, a dependency of the convective heat transfer on the air jet trajectory has been observed. New correlations have been developed, introducing a modified Archimedes number to account for the air flow pattern. The accuracy of the new correlations has been...... evaluated to±15%. Besides the study with an air-based cooling system, the convective heat transfer with a radiant cooling system has also been investigated. The convective flow at the activated surface is mainly driven by natural convection. For other surfaces, the complexity of the flow and the large......The complexity and diversity of airflow in buildings make the accurate definition of convective heat transfer coefficients (CHTCs) difficult. In a full-scale test facility, the convective heat transfer of two cooling systems (active chilled beam and radiant wall) has been investigated under steady...

Numerical study of the underexpanded nitrogen jets submerged into liquid sodium in the frame of Sodium-cooled Fast Reactor (SFRs)

International Nuclear Information System (INIS)

Chen, F.; Allou, A.; Parisse, J.D.

2017-01-01

The study of the consequences of a gas leakage in the secondary/ tertiary heat exchangers is one of the essential points in the safety analysis of Sodium-cooled Fast nuclear Reactors (SFRs). This work is in the frame of the technology of the Compact plates Sodium-Gas heat Exchangers (ECSG) which is an alternative to conventional steam Rankine cycles. The overpressure of the tertiary nitrogen loop causes the formation of underexpanded gas jets submerged in the liquid sodium. In order to establish a safety evaluation, it would be an asset to be able to estimate the leakage. The gas leak detection by the acoustic method based on the bubbles field has been proposed. It requires then a delicate knowledge of the bubble field. This work contributes to development a numerical tool and its validation to model the transport and the production of bubbles in the downstream of underexpanded gas jets. The code CANOP modeling bi-phasic compressible flow is investigated under the actual condition of the underexpanded nitrogen jets submerged in the liquid sodium in an ECSG channel. Expensive computational cost is limited by using an Adaptive Mesh Refinement. (author)

Thermal-hydraulic performance of a multiple jet cooling module with a concave dimple array in a helium-cooled divertor

Energy Technology Data Exchange (ETDEWEB)

Jung, Hyo-Yeon; Kim, Kwang-Yong, E-mail: kykim@inha.ac.kr

2017-01-15

A numerical study was performed to evaluate the thermal-hydraulic performance of a finger type cooling module, where multiple jets impinge on the surface with concave dimples, in the divertor of a nuclear fusion reactor. Conjugate heat transfer was analyzed in both the solid and fluid domains using three-dimensional Reynolds-averaged Navier-Stokes equations with the shear stress transport turbulence model. The computational domain consisted of a single fluid domain and three solid domains: tile, thimble, and cartridge. The numerical results for the temperature variation on the tile were validated in comparison with the experimental data. A parametric study was performed with two design variables, the ratios of dimple diameter and dimple height to the nozzle diameter, and two dimple arrays (inline and staggered arrays). The parametric study showed that the heat transfer rate was increased by up to 2.62% by introducing concave dimples, and that the heat transfer and pressure drop performances increased with increasing diameter and height of the dimples for a specified dimple array.

The JET divertor coil

International Nuclear Information System (INIS)

Last, J.R.; Froger, C.; Sborchia, C.

1989-01-01

The divertor coil is mounted inside the Jet vacuum vessel and is able to carry 1 MA turns. It is of conventional construction - water cooled copper, epoxy glass insulation -and is contained in a thin stainless steel case. The coil has to be assembled, insulated and encased inside the Jet vacuum vessel. A description of the coil is given, together with technical information (including mechanical effects on the vacuum vessel), an outline of the manufacture process and a time schedule. (author)

Lubrication and cooling for high speed gears

Science.gov (United States)

Townsend, D. P.

1985-01-01

The problems and failures occurring with the operation of high speed gears are discussed. The gearing losses associated with high speed gearing such as tooth mesh friction, bearing friction, churning, and windage are discussed with various ways shown to help reduce these losses and thereby improve efficiency. Several different methods of oil jet lubrication for high speed gearing are given such as into mesh, out of mesh, and radial jet lubrication. The experiments and analytical results for the various methods of oil jet lubrication are shown with the strengths and weaknesses of each method discussed. The analytical and experimental results of gear lubrication and cooling at various test conditions are presented. These results show the very definite need of improved methods of gear cooling at high speed and high load conditions.

Does Thermal Granulation Drive Tephra Jets?

Science.gov (United States)

White, J. D.; Zimanowski, B.; Buettner, R.; Sonder, I.; Dellino, P.

2011-12-01

Surtseyan tephra jets, also called cypressoid or cock's tail plumes, comprise a characteristic mixture of ash with bombs travelling roughly ballistic paths that tip the individual fingers of the projecting jet. Jets of similar form but smaller scale are generated by littoral magma-water interactions, confirming the general inference that surtseyan tephra jets are a characteristic product of explosive magma-water interaction, and suggesting that magmatic volatiles play a subsidiary role, if any, in their formation. Surtseyan jets have been inferred to result from both intense fuel-coolant interactions, and from simple boiling of water entrained into rising magma, and little new information has become available to test these two positions since they were clearly developed in the 1980s. Recent experiments in which magma is poured into standing water have produced vigorous jetting of hot water as melt solidifies and undergoes extensive thermal granulation. We present high-resolution hi-speed video of these jets, which we see as having the following origin. As thermal granulation takes place, a fracture network advances into the melt/glass body, and water invading the cracks at the rate of propagation is heated nearly instantaneously. Vapor produced at the contact expands and drives outward through cooled cracks, condensing as it moves to the exterior of the magma body where it is emitted as a jet of hot water. In ocean ridge hydrothermal systems a diffuse crack network inducts cold water, which is heated and expelled in focused jets. Focusing of hot outflow in experiments is inferred to result, as suggested for ridge hydrothermal systems, from thermoelastic closure of cracks near the one(s) feeding the jet. From the cooled products of our experimental runs, we know that thermal contraction produces a network of curved cracks with modal spacing of 1-2 mm, which separate domains of unbroken glass. It is during growth of this crack network that cold water enters, is

The Ongoing Catastrophe

DEFF Research Database (Denmark)

Kublitz, Anja

2015-01-01

as camps. Based on fieldwork among Palestinians in the Danish camps, this article explores why my interlocutors describe their current lives as a catastrophe. Al-Nakba literally means the catastrophe and, in Palestinian national discourse, it is used to designate the event of 1948, when the Palestinians...

Outdoor Performance Analysis of a Photovoltaic Thermal (PVT) Collector with Jet Impingement and Compound Parabolic Concentrator (CPC).

Science.gov (United States)

Jaaz, Ahed Hameed; Hasan, Husam Abdulrasool; Sopian, Kamaruzzaman; Kadhum, Abdul Amir H; Gaaz, Tayser Sumer; Al-Amiery, Ahmed A

2017-08-01

This paper discusses the effect of jet impingement of water on a photovoltaic thermal (PVT) collector and compound parabolic concentrators (CPC) on electrical efficiency, thermal efficiency and power production of a PVT system. A prototype of a PVT solar water collector installed with a jet impingement and CPC has been designed, fabricated and experimentally investigated. The efficiency of the system can be improved by using jet impingement of water to decrease the temperature of the solar cells. The electrical efficiency and power output are directly correlated with the mass flow rate. The results show that electrical efficiency was improved by 7% when using CPC and jet impingement cooling in a PVT solar collector at 1:00 p.m. (solar irradiance of 1050 W/m² and an ambient temperature of 33.5 °C). It can also be seen that the power output improved by 36% when using jet impingement cooling with CPC, and 20% without CPC in the photovoltaic (PV) module at 1:30 p.m. The short-circuit current I SC of the PV module experienced an improvement of ~28% when using jet impingement cooling with CPC, and 11.7% without CPC. The output of the PV module was enhanced by 31% when using jet impingement cooling with CPC, and 16% without CPC.

Influence of hole imperfection on jet cross flow interaction

International Nuclear Information System (INIS)

Jovanovic, M.B.; Lange, H.C. de; Steenhoven, A.A. van

2006-01-01

The influence of a small hole geometry variation on the jet cross flow interaction is investigated experimentally using particle image velocimetry and liquid crystal thermography. The flow characteristics correspond to film cooling in gas turbines. A production imperfection is represented with the small variation of the hole geometry. The experiments were conducted without and with the hole imperfection at three velocity ratios. If the imperfection is absent, the flow field is stable and clockwise vortices are detected downstream. The imperfection blocks the hole, accelerates the jet and changes the formation of large vortical structures. It produces the additional windward vortices, which influence the flow field and enhance the inflow of the cross-stream towards the cooled surface. The imperfection reduces the film cooling effectiveness

Analysis of expediency to set regulators of high-pressure emergency core cooling system of WWER 1000 (B-320)

International Nuclear Information System (INIS)

Skalozubov, V.I.; Komarov, Yu.A.; Tikhonova, G.G.; Nikiforov, S.N.; Bogodist, V.V.; Fol'tov, I.M.; Khadzh Faradzhallakh Dabbakh, A.

2011-01-01

The work shows that setting regulative valves in high-pressure emergency core cooling system of WWER 1000/B-320 can be effective only involving the additional tuning to account traverse speed of operating elements of regulator and configuration of the systems providing cooling of primary loop.

Jet pumps hydrdynamics for application on BWRS

International Nuclear Information System (INIS)

Girardi, G.; Pitimada, D.

1979-01-01

An analysis of single-phase jet-pump hydrodynamics is carried out by this paper with special regard to the applications on cooling water recirculation in the boiling water reactors (BWR). Firstly, in order to asses on efficiency of jet pumps, several theories regarding the hydrodynamic of these machines are also investigated. The results of the above theories are critically analysed and compared regarding to water-jet-pump design, to operational performance curves and to section limits. Some general criteria in jet-pump design are introduced and values of geometric and kinematic parameters are suggested together with losses coefficients which are all concerned with the ''high ratio'' type jet pump of this typical application. Finally, the experimental test program following the sim of this research is briefly described

Manufacturing and testing of a copper/CFC divertor mock-up for JET

International Nuclear Information System (INIS)

Brossa, M.; Ciric, D.; Deksnis, E.; Falter, H.; Guerreschi, U.; Peacock, A.; Pick, M.; Rossi, M.; Shen, Y.; Zacchia, F.

1995-01-01

An actively cooled divertor is a possible option for future developments at The Joint European Torus (JET). A proof of principle actively cooled tile has been produced in order to qualify the relevant manufacturing technologies and the non destructive control processes. In this frame Ansaldo Ricerche (ARI) has been involved in the construction of a mock-up comprising 6 OFHC copper tubes for water cooling that are brazed to a plate made out of carbon fibre composite (CFC). The final objective was the high heat flux testing of the mock-up at JET in order to evaluate the general behaviour of the component under relevant operating conditions. The key point of the work was the realisation of a sound joint by adapting the expertise gained in ARI in previous R and D activities on brazing heterogeneous materials. Reliable methods for ultrasonic examinations of the pieces were also set up. For successful application to the JET pumped divertor a water-cooled CFC target plate must show surface temperatures of 2 . Furthermore, global hydraulic considerations specific to JET limit the system pressure to 0.7 MPa. In such a design, critical heat flux is not the key limit, rather the reliability of the CFC-copper joint in terms of extent of wetting. First tests in the neutral beam test bed at JET show an adequate response for fluxes up to 15 MW/m 2 . (orig.)

Diffusion-based neuromodulation can eliminate catastrophic forgetting in simple neural networks

Science.gov (United States)

Clune, Jeff

2017-01-01

A long-term goal of AI is to produce agents that can learn a diversity of skills throughout their lifetimes and continuously improve those skills via experience. A longstanding obstacle towards that goal is catastrophic forgetting, which is when learning new information erases previously learned information. Catastrophic forgetting occurs in artificial neural networks (ANNs), which have fueled most recent advances in AI. A recent paper proposed that catastrophic forgetting in ANNs can be reduced by promoting modularity, which can limit forgetting by isolating task information to specific clusters of nodes and connections (functional modules). While the prior work did show that modular ANNs suffered less from catastrophic forgetting, it was not able to produce ANNs that possessed task-specific functional modules, thereby leaving the main theory regarding modularity and forgetting untested. We introduce diffusion-based neuromodulation, which simulates the release of diffusing, neuromodulatory chemicals within an ANN that can modulate (i.e. up or down regulate) learning in a spatial region. On the simple diagnostic problem from the prior work, diffusion-based neuromodulation 1) induces task-specific learning in groups of nodes and connections (task-specific localized learning), which 2) produces functional modules for each subtask, and 3) yields higher performance by eliminating catastrophic forgetting. Overall, our results suggest that diffusion-based neuromodulation promotes task-specific localized learning and functional modularity, which can help solve the challenging, but important problem of catastrophic forgetting. PMID:29145413

Diffusion-based neuromodulation can eliminate catastrophic forgetting in simple neural networks.

Directory of Open Access Journals (Sweden)

Roby Velez

Full Text Available A long-term goal of AI is to produce agents that can learn a diversity of skills throughout their lifetimes and continuously improve those skills via experience. A longstanding obstacle towards that goal is catastrophic forgetting, which is when learning new information erases previously learned information. Catastrophic forgetting occurs in artificial neural networks (ANNs, which have fueled most recent advances in AI. A recent paper proposed that catastrophic forgetting in ANNs can be reduced by promoting modularity, which can limit forgetting by isolating task information to specific clusters of nodes and connections (functional modules. While the prior work did show that modular ANNs suffered less from catastrophic forgetting, it was not able to produce ANNs that possessed task-specific functional modules, thereby leaving the main theory regarding modularity and forgetting untested. We introduce diffusion-based neuromodulation, which simulates the release of diffusing, neuromodulatory chemicals within an ANN that can modulate (i.e. up or down regulate learning in a spatial region. On the simple diagnostic problem from the prior work, diffusion-based neuromodulation 1 induces task-specific learning in groups of nodes and connections (task-specific localized learning, which 2 produces functional modules for each subtask, and 3 yields higher performance by eliminating catastrophic forgetting. Overall, our results suggest that diffusion-based neuromodulation promotes task-specific localized learning and functional modularity, which can help solve the challenging, but important problem of catastrophic forgetting.

He-cooled divertor for DEMO. Fabrication technology for tungsten cooling fingers

Energy Technology Data Exchange (ETDEWEB)

Reiser, J.; Norajitra, P.; Widak, V.; Krauss, W. [Forschungszentrum Karlsruhe GmbH (Germany)

2008-07-01

A modular helium-cooled divertor design based on the multi-jet impingement concept (HEMJ) has been developed for the ''post-ITER'' demonstration reactor (DEMO) at the Forschungszentrum Karlsruhe [1, 2]. The main function of the divertor is to keep the plasma free from impurities by catching particles, such as fusion ash and eroded particles from the first wall. From the divertor surface, a maximum heat load of 10 MW/m{sup 2} at least has to be removed. The whole divertor is split up into a number of cassettes (48 according to the latest design studies [3]). Each cassette is cooled separately. The target plates are provided with several cooling fingers to keep the thermal stresses low. Each cooling finger consists of a tungsten tile which is brazed to a thimble-like cap made of a tungsten alloy W-1%La2O3 (WL10) underneath. The thimble has to be connected to the ODS EUROFER steel structure, which is accomplished by brazing again. The tungsten/tungsten brazing is exposed to 1200 C operation temperature while the tungsten/steel brazing joint must withstand 700 C operating temperature. Cooling of the finger is achieved by multi-jet impingement with helium. The inlet temperature of helium is 600 C and rises up to 700 C at the outlet. With this kind of cooling, a mean heat transfer coefficient of 35.000 W/(m{sup 2*}K) can be reached. This compact report will focus on the manufacturing of such a cooling finger unit at FZK. It will cover the machining of the tungsten tile as well as of the thimble and, the brazing of the parts. The major aim of this activity is, on the one hand, to obtain functioning mock-ups with high quality and high reliability, in particular in terms of minimising the surface roughness, cracks, and micro-cracks. On the other hand, effort should also be laid on realising the mass production from economic point of view. (orig.)

RESEARCH OF INFLUENCE OF THE RODS CONSTRUCTION ON THEIR COOLING ABILITY AT FROSTING OF SILUMINS BY METHOD OF NUMERICAL MODELING

Directory of Open Access Journals (Sweden)

V. Yu. Stetsenko

2012-01-01

Full Text Available Numerical modeling of heat transfer coefficient on the surface of the water-cooled rod with a slotted and jet cooling was made.  calculations were carried out in a free, open  source  CFD software package OpenFOAM. it is shown that jet cooling is more uniform and intense compared to the slotted cooling. 

Outdoor Performance Analysis of a Photovoltaic Thermal (PVT Collector with Jet Impingement and Compound Parabolic Concentrator (CPC

Directory of Open Access Journals (Sweden)

Ahed Hameed Jaaz

2017-08-01

Full Text Available This paper discusses the effect of jet impingement of water on a photovoltaic thermal (PVT collector and compound parabolic concentrators (CPC on electrical efficiency, thermal efficiency and power production of a PVT system. A prototype of a PVT solar water collector installed with a jet impingement and CPC has been designed, fabricated and experimentally investigated. The efficiency of the system can be improved by using jet impingement of water to decrease the temperature of the solar cells. The electrical efficiency and power output are directly correlated with the mass flow rate. The results show that electrical efficiency was improved by 7% when using CPC and jet impingement cooling in a PVT solar collector at 1:00 p.m. (solar irradiance of 1050 W/m2 and an ambient temperature of 33.5 °C. It can also be seen that the power output improved by 36% when using jet impingement cooling with CPC, and 20% without CPC in the photovoltaic (PV module at 1:30 p.m. The short-circuit current ISC of the PV module experienced an improvement of ~28% when using jet impingement cooling with CPC, and 11.7% without CPC. The output of the PV module was enhanced by 31% when using jet impingement cooling with CPC, and 16% without CPC.

A charge regulating system for turbo-generator gas-cooled high-temperature reactor power stations

International Nuclear Information System (INIS)

Braytenbah, A.S.; Jaegtnes, K.O.

1975-01-01

The invention relates to a regulating system for gas-cooled high-temperature reactors power stations (helium coolant), equipped with several steam-boilers, each of which deriving heat from a corresponding cooling-gas flow circulating in the reactor, so as to feed superheated steam into a main common steam-manifold and re-superheated steam into a re-superheated hot common manifold [fr

Jet disruption in wide-angle tailed radio galaxies

International Nuclear Information System (INIS)

Burns, J.O.; Norman, M.L.; Clarke, D.A.

1986-01-01

The mechanisms responsible for the bending of the jets and tails of wide-angle tailed (WAT) radio galaxies in clusters are investigated theoretically, with a focus on sharp bends and rapid jet disruption. Large (1 Mpc) and small (200 kpc) WATs are differentiated, and it is suggested that the jet-tail transition in large WATs is due to collisions between the jet and cool clouds of the intracluster medium (ICM). The transition in small WATs is attributed to the passage of the jet through a planar Mach disk perpendicular to the jet flow direction. Such a disk is shown in numerical simulations to form when there is a shocklike jump in ambient pressure at the ISM/ICM interface; the origins of such a jump are explored. 14 references

Effect of guide wall on jet impingement cooling in blade leading edge channel

International Nuclear Information System (INIS)

Zhao, Qing-Yang; Chung, Heeyoon; Choi, Seok Min; Cho, Hyung Hee

2016-01-01

The characteristics of fluid flow and heat transfer, which are affected by the guide wall in a jet impinged leading edge channel, have been investigated numerically using three-dimensional Reynolds-averaged Navier-Stokes analysis via the shear stress transport turbulence model and gamma theta transitional turbulence model. A constant wall heat flux condition has been applied to the leading edge surface. The jet-to-surface distance is constant, which is three times that of the jet diameter. The arrangement of the guide wall near the jet hole is set as a variable. Results presented in this study include the Nusselt number contour, velocity vector, streamline with velocity, and local Nusselt number distribution along the central line on the leading edge surface. The average Nusselt number and average pressure loss between jet nozzle and channel exit are calculated to assess the thermal performance. The application of the guide wall is aimed at improving heat transfer uniformity on the leading edge surface. Results indicated that the streamwise guide wall ensures the vertical jet impingement flow intensity and prevents the flow after impingement to reflux into jet flow. Thus, a combined rectangular guide wall benefits the average heat transfer, thermal performance and heat transfer distribution uniformity

Isothermal and Reactive Turbulent Jets in Cross-Flow

Science.gov (United States)

Gutmark, Ephraim; Bush, Scott; Ibrahim, Irene

2004-11-01

Jets in cross flow have numerous applications including vertical/short takeoff/landing (V/STOL) aircraft, cooling jets for gas turbine blades and combustion air supply inlets in gas turbine engine. The properties exhibited by these jets are dictated by complex three dimensional turbulence structures which form due to the interaction of the jet with the freestream. The isothermal tests are conducted in a wind tunnel measuring the characteristics of air jets injected perpendicular into an otherwise undisturbed air stream. Different nozzle exit geometries of the air jets were tested including circular, triangular and elongated configurations. Jets are injected in single and paired combinations with other jets to measure the effect of mutual interaction on the parameters mentioned. Quantitative velocity fields are obtained using PIV. The data obtained allows the extraction of flow parameters such as jet structure, penetration and mixing. The reacting tests include separate and combined jets of fuel/air mixture utilized to explore the stabilization of combustion at various operating conditions. Different geometrical configurations of transverse jets are tested to determine the shape and combination of jets that will optimize the jets ability to successfully stabilize a flame.

Device for preventing cooling water from flowing out of reactor

International Nuclear Information System (INIS)

Chinen, Masanori; Kotani, Koichi; Murase, Michio.

1976-01-01

Object: To provide emergency cooling system, which can prevent cooling water bearing radioactivity from flowing to the outside of the reactor at the time of breakage of feedwater pipe, thus eliminating the possibility of exposure of the fuel rod to provide high reliability and also reducing the possibility of causing radioactive pollution. Structure: The device for preventing cooling water from flowing out from the reactor features a jet nozzle inserted in a feedwater pipe adjacent to the inlet or outlet thereof immediately before the reactor container. The nozzle outlet is provided in the vicinity of the reactor wall and in a direction opposite to the direction of out-flow, and water supplied from a high pressure pump is jetted from it. (Nakamura, S.)

Coping with ecological catastrophe: crossing major thresholds

Directory of Open Access Journals (Sweden)

John Cairns, Jr.

2004-08-01

Full Text Available The combination of human population growth and resource depletion makes catastrophes highly probable. No long-term solutions to the problems of humankind will be discovered unless sustainable use of the planet is achieved. The essential first step toward this goal is avoiding or coping with global catastrophes that result from crossing major ecological thresholds. Decreasing the number of global catastrophes will reduce the risks associated with destabilizing ecological systems, which could, in turn, destabilize societal systems. Many catastrophes will be local, regional, or national, but even these upheavals will have global consequences. Catastrophes will be the result of unsustainable practices and the misuse of technology. However, avoiding ecological catastrophes will depend on the development of eco-ethics, which is subject to progressive maturation, comments, and criticism. Some illustrative catastrophes have been selected to display some preliminary issues of eco-ethics.

CFD analysis of the impingement cooling effect of the coolant jet caused by the T56 1st stage disc metering hole

CSIR Research Space (South Africa)

Snedden, Glen C

2003-09-01

Full Text Available conditions applied is given in Figure 2. Figures 3 to 7 give an overview of the final mesh and some idea of the block structured approach and refinement in the main area of interest, that is, the impingement zone and metering holes at the lower part... OF THE IMPINGEMENT COOLING EFFECT OF THE COOLANT JET CAUSED BY THE T56 1ST STAGE DISC METERING HOLE ISABE-2003-1065 Glen C. Snedden CSIR, Defencetek, P O Box 395 Pretoria, 0001, South Africa Tony Lambert Rolls-Royce Indianapolis, Indiana, USA Abstract...

Quantum catastrophe of slow light

OpenAIRE

Leonhardt, Ulf

2001-01-01

Catastrophes are at the heart of many fascinating optical phenomena. The rainbow, for example, is a ray catastrophe where light rays become infinitely intense. The wave nature of light resolves the infinities of ray catastrophes while drawing delicate interference patterns such as the supernumerary arcs of the rainbow. Black holes cause wave singularities. Waves oscillate with infinitely small wave lengths at the event horizon where time stands still. The quantum nature of light avoids this h...

Numerical Analysis of Film Cooling at High Blowing Ratio

Science.gov (United States)

El-Gabry, Lamyaa; Heidmann, James; Ameri, Ali

2009-01-01

Computational Fluid Dynamics is used in the analysis of a film cooling jet in crossflow. Predictions of film effectiveness are compared with experimental results for a circular jet at blowing ratios ranging from 0.5 to 2.0. Film effectiveness is a surface quantity which alone is insufficient in understanding the source and finding a remedy for shortcomings of the numerical model. Therefore, in addition, comparisons are made to flow field measurements of temperature along the jet centerline. These comparisons show that the CFD model is accurately predicting the extent and trajectory of the film cooling jet; however, there is a lack of agreement in the near-wall region downstream of the film hole. The effects of main stream turbulence conditions, boundary layer thickness, turbulence modeling, and numerical artificial dissipation are evaluated and found to have an insufficient impact in the wake region of separated films (i.e. cannot account for the discrepancy between measured and predicted centerline fluid temperatures). Analyses of low and moderate blowing ratio cases are carried out and results are in good agreement with data.

Impact of environmental regulations on control of copper ion concentration in the DIII-D cooling water system

International Nuclear Information System (INIS)

Gootgeld, A.M.

1993-10-01

Tokamaks and industrial users are faced with the task of maintaining closed-loop, low conductivity, low impurity, cooling water systems. Operating these systems concentrates the impurities in the water requiring subsequent disposal. Environmental regulations are making this increasingly difficult. This paper will discuss the solution to the problem of removing and disposing of copper ions in the DIII-D low conductivity water system. Since the commissioning of the Doublet facility, the quality of the water in the 3000 gpm system that cools the DIII-D vacuum vessel coils, power supplies and auxiliary heating components has been controlled with mixed-bed ion exchangers. Low ion levels, particularly copper, are required to operate this equipment. In early 1992, the company that leases and regenerates DIII-D ion exchangers said they no longer can accept these resin beds for regeneration due to the level of copper ion on the resin. This change in policy, a change that has been adopted throughout their industry, was necessary to assure that the Metropolitan Sewerage System of the City of San Diego stays in compliance with State of California regulations and EPA-mandated national pretreatment standards and regulations. A cost effective solution was implemented which utilizes a reverse osmosis filtration system with the ion exchangers for make-up water. Levels of copper ion disposed to the sewer are in compliance with government standards. These measures have thus far proved effective in maintaining low conductivity and overall good quality cooling water. Specifically, this paper discusses DIII-D deionized cooling water quality requirements and an affective means to meet these requirements in order to be in compliance with government regulations for copper ion disposal. The problems discussed, the alternatives considered and the approach taken would be readily applicable to any deionized cooling water system containing copper where EPA standards and regulations are mandated

Evaluation of water cooled supersonic temperature and pressure probes for application to 2000 F flows

Science.gov (United States)

Lagen, Nicholas T.; Seiner, John M.

1990-01-01

The development of water cooled supersonic probes used to study high temperature jet plumes is addressed. These probes are: total pressure, static pressure, and total temperature. The motivation for these experiments is the determination of high temperature supersonic jet mean flow properties. A 3.54 inch exit diameter water cooled nozzle was used in the tests. It is designed for exit Mach 2 at 2000 F exit total temperature. Tests were conducted using water cooled probes capable of operating in Mach 2 flow, up to 2000 F total temperature. Of the two designs tested, an annular cooling method was chosen as superior. Data at the jet exit planes, and along the jet centerline, were obtained for total temperatures of 900 F, 1500 F, and 2000 F, for each of the probes. The data obtained from the total and static pressure probes are consistent with prior low temperature results. However, the data obtained from the total temperature probe was affected by the water coolant. The total temperature probe was tested up to 2000 F with, and without, the cooling system turned on to better understand the heat transfer process at the thermocouple bead. The rate of heat transfer across the thermocouple bead was greater when the coolant was turned on than when the coolant was turned off. This accounted for the lower temperature measurement by the cooled probe. The velocity and Mach number at the exit plane and centerline locations were determined from the Rayleigh-Pitot tube formula.

Catastrophizing in Patients with Burning Mouth Syndrome

Directory of Open Access Journals (Sweden)

Ana ANDABAK ROGULJ

2014-01-01

Full Text Available Background: Burning mouth syndrome (BMS is an idiopathic painful condition which manifests with burning sensations in the oral cavity in patients with clinically normal oral mucosa and without any local and/or systemic causative factor. Catastrophizing is defined as an exaggerated negative orientation toward pain stimuli and pain experience. The aim of this study was to examine the association between catastrophizing and clinical parameters of BMS, and to examine the association between catastrophizing and the quality of life in patients with BMS. Materials and methods: Anonymous questionnaire consisting of 3 parts (demographic and clinical data with 100 mm visual analogue scale (VAS, Croatian version of the Oral Health Impact Profile (OHIP-14 scale and Croatian version of the Pain Catastrophizing scale (PC, was distributed to 30 patients diagnosed with BMS. Results: A higher level of catastrophizing was clinically significant in 30% of the patients. Total catastrophizing score and all three subcomponents of catastrophizing significantly correlated with the intensity of symptoms, but did not correlate with the duration of symptoms. Gender and previous treatment did not affect the catastrophizing. Conclusion: Obtaining the information about catastrophizing could help a clinician to identify patients with negative behavioural patterns. Additional psychological intervention in these individuals could reduce/eliminate negative cognitive factors and improve coping with chronic painful condition such as BMS.

Experimental investigation of submerged single jet impingement using Cu–water nanofluid

International Nuclear Information System (INIS)

Li Qiang; Xuan Yimin; Yu Feng

2012-01-01

Jet impingement cooling is a vital technique for thermal management of electronic devices of high-heat-flux by impinging fluid on a heater surface due to its high local heat transfer rates. In this paper, two types of Cu–water nanofluids (Cu particles with 25 nm diameter or 100 nm) are introduced into submerged single jet impingement cooling system as the working fluid. The heat transfer features of the nanofluids were experimentally investigated. The effects of the nanoparticle concentration, Reynolds number, nozzle-to-plate distance, fluid temperature, and nanoparticle diameter on the heat transfer performances of the jet impingement of nanofluids are discussed. The experimental results show that the suspended nanoparticles remarkably increase the convective heat transfer coefficient of the base fluid. The convective heat transfer coefficient of Cu–water nanofluid with the volume fraction of 3.0% has 52% higher than the pure water. The experiments also revealed that the suspended nanoparticles brought almost no extra addition of pressure drop in both submerged single jet impingement. In addition, by considering the effects of the suspended nanoparticles as well as the condition of impinging jet, a new heat transfer correlation of nanofluids for the submerged single jet impingement has been proposed. - Highlights: ► Cu–water nanofluids are introduced into submerged single jet impingement. ► The affecting parameters on the heat transfer performances of nanofluids are discussed. ► New heat transfer correlation of nanofluid for single jet impingement is proposed.

Marginally fast cooling synchrotron models for prompt GRBs

Science.gov (United States)

Beniamini, Paz; Barniol Duran, Rodolfo; Giannios, Dimitrios

2018-05-01

Previous studies have considered synchrotron as the emission mechanism for prompt gamma-ray bursts (GRBs). These works have shown that the electrons must cool on a time-scale comparable to the dynamic time at the source in order to satisfy spectral constraints while maintaining high radiative efficiency. We focus on conditions where synchrotron cooling is balanced by a continuous source of heating, and in which these constraints are naturally satisfied. Assuming that a majority of the electrons in the emitting region are contributing to the observed peak, we find that the energy per electron has to be E ≳ 20 GeV and that the Lorentz factor of the emitting material has to be very large 103 ≲ Γem ≲ 104, well in excess of the bulk Lorentz factor of the jet inferred from GRB afterglows. A number of independent constraints then indicate that the emitters must be moving relativistically, with Γ΄ ≈ 10, relative to the bulk frame of the jet and that the jet must be highly magnetized upstream of the emission region, σup ≳ 30. The emission radius is also strongly constrained in this model to R ≳ 1016 cm. These values are consistent with magnetic jet models where the dissipation is driven by magnetic reconnection that takes place far away from the base of the jet.

Physics basis and mechanical design of the actively cooled duct scraper protection for the JET neutral beam enhancement

Energy Technology Data Exchange (ETDEWEB)

Wilson, D.J. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)], E-mail: dwilson@jet.uk; Ciric, D.; Cox, S.J.; Jones, T.T.C.; Kovari, M. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Li Puma, A. [Association EURATOM-CEA, CEA-Cadarache, 13108 St. Paul-Lez-Durance (France); Martin, D.; Milnes, J.; Shannon, M.; Surrey, E. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)

2007-10-15

The objectives of the JET neutral beam enhancement (NBE) include raising the delivered power from the present 25 MW to more than 34 MW and increasing the pulse length from 10 to 20 s. The additional power will be obtained partly by increasing the fractional energy components of the beam, resulting from acceleration of molecular ions, hence increasing the total particle flux. These changes place extreme demands on the design of the upgraded protection to the torus entry duct. The present inertial duct protection already reaches its thermomechanical limit in 10 s pulses, and active cooling of the upgraded duct protection is therefore essential. Extensive analysis of the pressure and temperature evolution in the present un-cooled duct established the relationship between gas re-emission and surface temperature for copper in this operating environment. This information was used in an integrated physics and engineering approach to the design of the actively cooled duct protection, taking into account the power loads from direct beam interception and re-ionisation. Surface temperature determines power density through the gas re-emission and consequential beam re-ionisation. These considerations define the normal operating point for the chosen enhanced hypervapotron element technology. This approach demonstrated that supplementary in situ duct cryopumping would not be needed, provided that the required heat-transfer performance could be met without any encroachment of the elements beyond the space envelope of the existing inertial duct protection plates. This requirement posed severe constraints on the mechanical design of the hypervapotron element array and its manifolding; the adopted engineering design solutions are presented.

Adaptation to and Recovery from Global Catastrophe

Directory of Open Access Journals (Sweden)

Seth D. Baum

2013-03-01

Full Text Available Global catastrophes, such as nuclear war, pandemics and ecological collapse threaten the sustainability of human civilization. To date, most work on global catastrophes has focused on preventing the catastrophes, neglecting what happens to any catastrophe survivors. To address this gap in the literature, this paper discusses adaptation to and recovery from global catastrophe. The paper begins by discussing the importance of global catastrophe adaptation and recovery, noting that successful adaptation/recovery could have value on even astronomical scales. The paper then discusses how the adaptation/recovery could proceed and makes connections to several lines of research. Research on resilience theory is considered in detail and used to develop a new method for analyzing the environmental and social stressors that global catastrophe survivors would face. This method can help identify options for increasing survivor resilience and promoting successful adaptation and recovery. A key point is that survivors may exist in small isolated communities disconnected from global trade and, thus, must be able to survive and rebuild on their own. Understanding the conditions facing isolated survivors can help promote successful adaptation and recovery. That said, the processes of global catastrophe adaptation and recovery are highly complex and uncertain; further research would be of great value.

Heat/mass transfer on effusion plate with circular pin fins for impingement/effusion cooling system with initial crossflow

International Nuclear Information System (INIS)

Hong, Sung Kook; Rhee, Dong Ho; Cho, Hyung Hee

2005-01-01

Impingement/effusion cooling technique is used for combustor liner or turbine parts cooling in gas turbine engine. In the impingement/effusion cooling system, the crossflow generated in the cooling channel induces an adverse effect on the cooling performance, which consequently affects the durability of the cooling system. In the present study, to reduce the adverse effect of the crossflow and improve the cooling performance, circular pin fins are installed in impingement/effusion cooling system and the heat transfer characteristics are investigated. The pin fins are installed between two perforated plates and the crossflow passes between these two plates. A blowing ratio is changed from 0.5 to 1.5 for the fixed jet Reynolds number of 10,000 and five circular pin fin arrangements are considered in this study. The local heat/mass transfer coefficients on the effusion plate are measured using a naphthalene sublimation method. The results show that local distributions of heat/mass transfer coefficient are changed due to the installation of pin fins. Due to the generation of vortex and wake by the pin fin, locally low heat/mass transfer regions are reduced. Moreover, the pin fin prevents the wall jet from being swept away, resulting in the increase of heat/mass transfer. When the pin fin is installed in front of the impinging jet, the blockage effect on the crossflow enhances the heat/mass transfer. However, the pin fin installed just behind the impinging jet blocks up the wall jet, decreasing the heat/mass transfer. As the blowing ratio increases, the pin fins lead to the higher Sh value compared to the case without pin fins, inducing 16%∼22% enhancement of overall Sh value at high blowing ratio of M=1.5

Advantages of new micro-jet welding technology on weld microstructure control

Directory of Open Access Journals (Sweden)

Jan PIWNIK

2013-01-01

Full Text Available An innovative apparatus to welding process with micro-jet cooling of the weld made it possible to carry out technological tests, which have proved theoretical considerations about this problem. This project gives real opportunities for professional development in the field of welding with controlling the parameters of weld structure. These tests have proved that the new micro-jet technology has the potential for growth. It may be great achievement of welding technology in order to increase weld metal strength. The new technology with micro-jet cooling may have many practical applications in many fields, for example such as in the transport industry or to repair damaged metal elements. The advantages of the new device over the traditional system are the ability to control the structure of the weld, the weld mechanical performance increases and improve the quality of welded joints.

Transient thermal analysis of cryocondensation pump for JET

International Nuclear Information System (INIS)

Baxi, C.B.; Obert, W.

1993-08-01

A cryopump with pumping speed of 50,000 1/sec is planned to be installed in the Joint European Torus (JET) as part of the pumped divertor. The purpose of this pump is to control the plasma impurities. The pump consists of a helium panel cooled by supercritical helium and a nitrogen shield cooled by liquid nitrogen. This paper presents the following transient thermal flow analysis for this cryopump: 1. Consequences of loss of torus vacuum on helium panel. 2. Cool down of the nitrogen shield form 300 K to 80 K

Abrasive water jets for controlled demolition and dismantling

International Nuclear Information System (INIS)

Abudaka, M.; Crofton, P.S.J.

1988-01-01

Abrasive water jets offer an efficient high speed cutting tool for hard materials such as reinforced concrete, tool steel and armour plate. Cutting by abrasive water jets is often described as a cold cutting operation since no heat is developed and any increase in local temperature is immediately cooled by the water jet. Moreover no sparks are generated to ignite a potentially inflammable atmosphere. Mass flow rates of water and abrasive are small (typically 4 litres/min.water and 1 kg/min abrasive) and hence are easy to collect and to dispose of. For these reasons abrasive water jets offer certain advantages in cutting difficult materials in hazardous environments such as in the nuclear industry, offshore oil rigs and petrochemical plant. Available portable cutting systems are described and the advantages of using abrasive water jets are discussed as well as some of the parameters involved in the cutting operation. Finally a description is presented of some typical applications of abrasive water jet cutting. (author)

Investigation on the influence of jetting equipment on the characteristics of centrifugal pump

Directory of Open Access Journals (Sweden)

Qiaorui Si

2016-08-01

Full Text Available To reduce radial noises from the motor of centrifugal pumps, this study designed a water cooling system called jetting equipment to replace traditional fan cooling systems in pump motors. By measuring radiated noises, head, efficiency, and cavitation performance, the research compared the differences among experimental results of the original pump unit, the one with a normal design jetting pipe and another one with a larger jetting pipe. Results show that the radiated sound pressure level of the model pump was significantly reduced by 8.3 dB after integrating the jetting pipe. With a normal jetting pipe, no significant changes were observed in the head, efficiency, and shaft power curves, and cavitation performance improved under small flow rate. However, the performance with the larger jetting pipe worsened, except the hump phenomenon of the model pump under a small flow rate was enhanced. Computational fluid dynamics method was used to calculate the internal flow of three model pumps in order to investigate the jetting flow effect. A comparison among the flow fields at the inlet of the three types of pumps indicated that high-pressure water injection can effectively control inlet recirculation and improve velocity distribution in the inlet flow field with decreased recirculation vortex strength and recirculation onset critical flow rate.

Theory of a slow-light catastrophe

International Nuclear Information System (INIS)

Leonhardt, Ulf

2002-01-01

In diffraction catastrophes such as the rainbow, the wave nature of light resolves ray singularities and draws delicate interference patterns. In quantum catastrophes such as the black hole, the quantum nature of light resolves wave singularities and creates characteristic quantum effects related to Hawking radiation. This paper describes the theory behind a recent proposal [U. Leonhardt, Nature (London) 415, 406 (2002)] to generate a quantum catastrophe of slow light

Theory of a slow-light catastrophe

Science.gov (United States)

Leonhardt, Ulf

2002-04-01

In diffraction catastrophes such as the rainbow, the wave nature of light resolves ray singularities and draws delicate interference patterns. In quantum catastrophes such as the black hole, the quantum nature of light resolves wave singularities and creates characteristic quantum effects related to Hawking radiation. This paper describes the theory behind a recent proposal [U. Leonhardt, Nature (London) 415, 406 (2002)] to generate a quantum catastrophe of slow light.

Theory of a Slow-Light Catastrophe

OpenAIRE

Leonhardt, Ulf

2001-01-01

In diffraction catastrophes such as the rainbow the wave nature of light resolves ray singularities and draws delicate interference patterns. In quantum catastrophes such as the black hole the quantum nature of light resolves wave singularities and creates characteristic quantum effects related to Hawking radiation. The paper describes the theory behind a recent proposal [U. Leonhardt, arXiv:physics/0111058, Nature (in press)] to generate a quantum catastrophe of slow light.

Catastrophe theory with application in nuclear technology

International Nuclear Information System (INIS)

Valeca, Serban Constantin

2002-01-01

The monograph is structured on the following seven chapters: 1. Correlation of risk, catastrophe and chaos at the level of polyfunctional systems with nuclear injection; 1.1 Approaching the risk at the level of power systems; 1.2 Modelling the chaos-catastrophe-risk correlation in the structure of integrated classical and nuclear processes; 2. Catastrophe theory applied in ecosystems models and applications; 2.1 Posing the problems in catastrophe theory; 2.2 Application of catastrophe theory in the engineering of the power ecosystems with nuclear injection; 4.. Decision of abatement of the catastrophic risk based on minimal costs; 4.1 The nuclear power systems sensitive to risk-catastrophe-chaos in the structure of minimal costs; 4.2 Evaluating the market structure on the basis of power minimal costs; 4.3 Decisions in power systems built on minimal costs; 5. Models of computing the minimal costs in classical and nuclear power systems; 5.1 Calculation methodologies of power minimal cost; 5.2 Calculation methods of minimal costs in nuclear power sector; 6. Expert and neuro expert systems for supervising the risk-catastrophe-chaos correlation; 6.1 The structure of expert systems; 6.2 Application of the neuro expert program; 7. Conclusions and operational proposals; 7.1 A synthesis of the problems presented in this work; 7.2 Highlighting the novel aspects applicable in the power systems with nuclear injection

Well below 2 °C: Mitigation strategies for avoiding dangerous to catastrophic climate changes

Science.gov (United States)

Xu, Yangyang; Ramanathan, Veerabhadran

2017-09-01

The historic Paris Agreement calls for limiting global temperature rise to “well below 2 °C.” Because of uncertainties in emission scenarios, climate, and carbon cycle feedback, we interpret the Paris Agreement in terms of three climate risk categories and bring in considerations of low-probability (5%) high-impact (LPHI) warming in addition to the central (˜50% probability) value. The current risk category of dangerous warming is extended to more categories, which are defined by us here as follows: >1.5 °C as dangerous; >3 °C as catastrophic; and >5 °C as unknown, implying beyond catastrophic, including existential threats. With unchecked emissions, the central warming can reach the dangerous level within three decades, with the LPHI warming becoming catastrophic by 2050. We outline a three-lever strategy to limit the central warming below the dangerous level and the LPHI below the catastrophic level, both in the near term (pollutant (SP) lever to mitigate short-lived climate pollutants, and the carbon extraction and sequestration (CES) lever to thin the atmospheric CO2 blanket. Pulling on both CN and SP levers and bending the emissions curve by 2020 can keep the central warming below dangerous levels. To limit the LPHI warming below dangerous levels, the CES lever must be pulled as well to extract as much as 1 trillion tons of CO2 before 2100 to both limit the preindustrial to 2100 cumulative net CO2 emissions to 2.2 trillion tons and bend the warming curve to a cooling trend.

Numerical simulation of jet breakup behavior by the lattice Boltzmann method

International Nuclear Information System (INIS)

Matsuo, Eiji; Koyama, Kazuya; Abe, Yutaka; Iwasawa, Yuzuru; Ebihara, Ken-ichi

2015-01-01

In order to understand the jet breakup behavior of the molten core material into coolant during a core disruptive accident (CDA) for a sodium-cooled fast reactor (SFR), we simulated the jet breakup due to the hydrodynamic interaction using the lattice Boltzmann method (LBM). The applicability of the LBM to the jet breakup simulation was validated by comparison with our experimental data. In addition, the influence of several dimensionless numbers such as Weber number and Froude number was examined using the LBM. As a result, we validated applicability of the LBM to the jet breakup simulation, and found that the jet breakup length is independent of Froude number and in good agreement with the Epstein's correlation when the jet interface becomes unstable. (author)

Cryogenically assisted abrasive jet micromachining of polymers

International Nuclear Information System (INIS)

Getu, H; Papini, M; Spelt, J K

2008-01-01

The abrasive jet micromachining (AJM) of elastomers and polymers such as polydimethylsiloxane (PDMS), acrylonitrile butadiene styrene (ABS) and polytetrafluoroethylene (PTFE) for use in micro-fluidic devices was found to be very slow or impossible at room temperature. To enhance the material removal rate in such materials, a stream of liquid nitrogen (LN 2 ) was injected into the abrasive jet, cooling the target to cryogenic temperatures. Erosion rate measurements on the three polymeric materials (PDMS, ABS and PTFE) with and without the use of LN 2 were compared along with the profiles of micromachined channels and holes. It was found that the use of LN 2 cooling caused brittle erosion in PDMS, allowing it to be micromachined successfully. An erosion rate increase was also observed in PTFE and ABS at high and intermediate impact angles. The use of LN 2 also was found to reduce particle embedding

MAGNETIC FLUX CANCELATION AS THE TRIGGER OF SOLAR QUIET-REGION CORONAL JETS

Energy Technology Data Exchange (ETDEWEB)

Panesar, Navdeep K.; Sterling, Alphonse C.; Moore, Ronald L. [Heliophysics and Planetary Science Office, ZP13, Marshall Space Flight Center, Huntsville, AL 35812 (United States); Chakrapani, Prithi, E-mail: navdeep.k.panesar@nasa.gov [Hunter College High School, New York, NY (United States)

2016-11-20

We report observations of 10 random on-disk solar quiet-region coronal jets found in high-resolution extreme ultraviolet (EUV) images from the Solar Dynamics Observatory ( SDO )/Atmospheric Imaging Assembly and having good coverage in magnetograms from the SDO /Helioseismic and Magnetic Imager (HMI). Recent studies show that coronal jets are driven by the eruption of a small-scale filament (called a minifilament ). However, the trigger of these eruptions is still unknown. In the present study, we address the question: what leads to the jet-driving minifilament eruptions? The EUV observations show that there is a cool-transition-region-plasma minifilament present prior to each jet event and the minifilament eruption drives the jet. By examining pre-jet evolutionary changes in the line of sight photospheric magnetic field, we observe that each pre-jet minifilament resides over the neutral line between majority-polarity and minority-polarity patches of magnetic flux. In each of the 10 cases, the opposite-polarity patches approach and merge with each other (flux reduction between 21% and 57%). After several hours, continuous flux cancelation at the neutral line apparently destabilizes the field holding the cool-plasma minifilament to erupt and undergo internal reconnection, and external reconnection with the surrounding coronal field. The external reconnection opens the minifilament field allowing the minifilament material to escape outward, forming part of the jet spire. Thus, we found that each of the 10 jets resulted from eruption of a minifilament following flux cancelation at the neutral line under the minifilament. These observations establish that magnetic flux cancelation is usually the trigger of quiet-region coronal jet eruptions.

How are the catastrophical risks quantifiable

International Nuclear Information System (INIS)

Chakraborty, S.

1985-01-01

For the assessment and evaluation of industrial risks the question must be asked how are the catastrophical risks quantifiable. Typical real catastrophical risks and risk assessment based on modelling assumptions have been placed against each other in order to put the risks into proper perspective. However, the society is risk averse when there is a catastrophic potential of severe accidents in a large scale industrial facility even though there is extremely low probability of occurence. (orig.) [de

Environmental catastrophes under time-inconsistent preference

Energy Technology Data Exchange (ETDEWEB)

Michielsen, T.

2013-02-15

I analyze optimal natural resource use in an intergenerational model with the risk of a catastrophe. Each generation maximizes a weighted sum of discounted utility (positive) and the probability that a catastrophe will occur at any point in the future (negative). The model generates time inconsistency as generations disagree on the relative weights on utility and catastrophe prevention. As a consequence, future generations emit too much from the current generation's perspective and a dynamic game ensues. I consider a sequence of models. When the environmental problem is related to a scarce exhaustible resource, early generations have an incentive to reduce emissions in Markov equilibrium in order to enhance the ecosystem's resilience to future emissions. When the pollutant is expected to become obsolete in the near future, early generations may however increase their emissions if this reduces future emissions. When polluting inputs are abundant and expected to remain essential, the catastrophe becomes a self-fulfilling prophecy and the degree of concern for catastrophe prevention has limited or even no effect on equilibrium behaviour.

Catastrophe medicine; Medecine de catastrophe

Energy Technology Data Exchange (ETDEWEB)

Lebreton, A. [Service Technique de l`Energie Electrique et des Grands Barrages (STEEGB), (France)

1996-12-31

The `Catastrophe Medicine` congress which took place in Amiens (France) in December 5 to 7 1996 was devoted to the assessment and management of risks and hazards in natural and artificial systems. The methods of risk evaluation and prevision were discussed in the context of dams accidents with the analysis of experience feedbacks and lessons gained from the organisation of emergency plans. Three round table conferences were devoted to the importance of psychological aspects during such major crises. (J.S.)

A Numerical Study of Anti-Vortex Film Cooling Designs at High Blowing Ratio

Science.gov (United States)

Heidmann, James D.

2008-01-01

A concept for mitigating the adverse effects of jet vorticity and liftoff at high blowing ratios for turbine film cooling flows has been developed and studied at NASA Glenn Research Center. This "anti-vortex" film cooling concept proposes the addition of two branched holes from each primary hole in order to produce a vorticity counter to the detrimental kidney vortices from the main jet. These vortices typically entrain hot freestream gas and are associated with jet separation from the turbine blade surface. The anti-vortex design is unique in that it requires only easily machinable round holes, unlike shaped film cooling holes and other advanced concepts. The anti-vortex film cooling hole concept has been modeled computationally for a single row of 30deg angled holes on a flat surface using the 3D Navier-Stokes solver Glenn-HT. A modification of the anti-vortex concept whereby the branched holes exit adjacent to the main hole has been studied computationally for blowing ratios of 1.0 and 2.0 and at density ratios of 1.0 and 2.0. This modified concept was selected because it has shown the most promise in recent experimental studies. The computational results show that the modified design improves the film cooling effectiveness relative to the round hole baseline and previous anti-vortex cases, in confirmation of the experimental studies.

Measurement of air entrainment in plasma jets

International Nuclear Information System (INIS)

Fincke, J.R.; Rodriquez, R.; Pentecost, C.G.

1990-01-01

The concentration and temperature of air entrained into argon and helium plasma jets has been measured using coherent anti-Stokes Raman spectroscopy (CARS). The argon plasma flow field is characterized by a short region of well behaved laminar flow near the nozzle exit followed by an abrupt transition to turbulence. Once the transition of turbulence occurs, air is rapidly mixed into the jet core. The location of the transition region is determined by the rapid cooling of the jet and the resulting increase in Reynolds number. In contrast, the helium plasma flow field never exceeds a Reynolds number of 200 and remains laminar. The entrainment process in this case is controlled by molecular diffusion rather than turbulent mixing. 9 refs., 5 figs., 1 tab

Axial and focal-plane diffraction catastrophe integrals

International Nuclear Information System (INIS)

Berry, M V; Howls, C J

2010-01-01

Exact expressions in terms of Bessel functions are found for some of the diffraction catastrophe integrals that decorate caustics in optics and mechanics. These are the axial and focal-plane sections of the elliptic and hyperbolic umbilic diffraction catastrophes, and symmetric elliptic and hyperbolic unfoldings of the X 9 diffraction catastrophes. These representations reveal unexpected relations between the integrals.

An experimental investigation of a liquid cooling scheme for the low dropout voltage regulators of the multiplicity and vertex detector

International Nuclear Information System (INIS)

Bernardin, J.D.; Bosze, E.

1997-10-01

This report presents a summary of an experimental investigation of a liquid cooling system for the low dropout voltage regulators in the multiplicity and vertex detector (MVD), a device used to determine and characterize the collision location of two accelerated heavy ions. The coolant temperatures and flow rates as well as the voltage regulator operating temperatures were used to assess and optimize the performance of the proposed cooling system, identify potential assembly problems and system limitations, and provide the necessary information for designing and sizing the final MVD cooling system components. The MVD is part of the PHENIX experiment at Brookhaven RHIC

Coronal Flux Rope Catastrophe Associated With Internal Energy Release

Science.gov (United States)

Zhuang, Bin; Hu, Youqiu; Wang, Yuming; Zhang, Quanhao; Liu, Rui; Gou, Tingyu; Shen, Chenglong

2018-04-01

Magnetic energy during the catastrophe was predominantly studied by the previous catastrophe works since it is believed to be the main energy supplier for the solar eruptions. However, the contribution of other types of energies during the catastrophe cannot be neglected. This paper studies the catastrophe of the coronal flux rope system in the solar wind background, with emphasis on the transformation of different types of energies during the catastrophe. The coronal flux rope is characterized by its axial and poloidal magnetic fluxes and total mass. It is shown that a catastrophe can be triggered by not only an increase but also a decrease of the axial magnetic flux. Moreover, the internal energy of the rope is found to be released during the catastrophe so as to provide energy for the upward eruption of the flux rope. As far as the magnetic energy is concerned, it provides only part of the energy release, or even increases during the catastrophe, so the internal energy may act as the dominant or even the unique energy supplier during the catastrophe.

Energy catastrophes and energy consumption

International Nuclear Information System (INIS)

Davis, G.

1991-01-01

The possibility of energy catastrophes in the production of energy serves to make estimation of the true social costs of energy production difficult. As a result, there is a distinct possibility that the private marginal cost curve of energy producers lies to the left or right of the true cost curve. If so, social welfare will not be maximized, and underconsumption or overconsumption of fuels will exist. The occurrence of energy catastrophes and observance of the market reaction to these occurrences indicates that overconsumption of energy has been the case in the past. Postulations as to market reactions to further energy catastrophes lead to the presumption that energy consumption levels remain above those that are socially optimal

Experimental observations and modelling of thermal history within a steel plate during water jet impingement

International Nuclear Information System (INIS)

Liu, Z.D.; Fraser, D.; Samarasekera, I.V.; Lockhart, G.T.

2002-01-01

In order to investigate heat transfer of steel plates under a water jet impingement and to further simulate runout table operation in a hot strip mill, a full-scale pilot runout table facility was designed and constructed at the University of British Columbia (UBC). This paper describes the experimental details, data acquisition and data handling techniques for steel plates during water jet impingement by one circular water jet from an industrial header. Recorded visual observations at the impinging surface were obtained. The effects of cooling water temperature and impingement velocity on the heat transfer from a steel plate were studied. A two-dimensional finite element method-based transient inverse heat conduction model was developed. With the help of the model, heat fluxes and heat transfer coefficients along the impinging surface under various cooling conditions were calculated. The microstructural evolution of the steel plate was also investigated for the varying cooling conditions. Samples were obtained from each plate, polished, etched and then photographed. (author)

Development of key fusion technologies at JET

International Nuclear Information System (INIS)

2001-01-01

The recent operational phase in JET in which Deuterium-Tritium fuel was used (DTE1) resulted in record breaking fusion performance. In addition to important contributions in plasma physics, the JET Team has also made major advances in demonstrating the viability of some of the key technologies required for the realisation of future fusion power. Two of the most important technological areas which have been successfully demonstrated in JET are the ITER scale tritium processing plant and the exchange of the divertor and maintenance of the interior of JET by totally remote means. The experiment also provided the first data on tritium retention and co-deposition in a diverted tokamak. Of the 35g of tritium injected into the JET torus, about 6g remained in the tokamak. The amount resides mainly on cool surfaces at the inboard divertor side. The precise, safe and timely execution of the remote handling shutdown proved that the design, function, performance and operational methodology of the RH equipment prepared over the years at JET are appropriate for the successful and rapid replacement of components in an activated tokamak environment. (author)

Development of key fusion technologies at JET

International Nuclear Information System (INIS)

1999-01-01

The recent operational phase in JET in which Deuterium-Tritium fuel was used (DTE1) resulted in record breaking fusion performance. In addition to important contributions in plasma physics, the JET Team has also made major advances in demonstrating the viability of some of the key technologies required for the realisation of future fusion power. Two of the most important technological areas which have been successfully demonstrated in JET are the ITER scale tritium processing plant and the exchange of the divertor and maintenance of the interior of JET by totally remote means. The experiment also provided the first data on tritium retention and co-deposition in a diverted tokamak. Of the 35g of tritium injected into the JET torus, about 6g remained in the tokamak. The amount resides mainly on cool surfaces at the inboard divertor side. The precise, safe and timely execution of the remote handling shutdown proved that the design, function, performance and operational methodology of the RH equipment prepared over the years at JET are appropriate for the successful and rapid replacement of components in an activated tokamak environment. (author)

Liquid Cooling System for CPU by Electroconjugate Fluid

Directory of Open Access Journals (Sweden)

Yasuo Sakurai

2014-06-01

Full Text Available The dissipated power of CPU for personal computer has been increased because the performance of personal computer becomes higher. Therefore, a liquid cooling system has been employed in some personal computers in order to improve their cooling performance. Electroconjugate fluid (ECF is one of the functional fluids. ECF has a remarkable property that a strong jet flow is generated between electrodes when a high voltage is applied to ECF through the electrodes. By using this strong jet flow, an ECF-pump with simple structure, no sliding portion, no noise, and no vibration seems to be able to be developed. And then, by the use of the ECF-pump, a new liquid cooling system by ECF seems to be realized. In this study, to realize this system, an ECF-pump is proposed and fabricated to investigate the basic characteristics of the ECF-pump experimentally. Next, by utilizing the ECF-pump, a model of a liquid cooling system by ECF is manufactured and some experiments are carried out to investigate the performance of this system. As a result, by using this system, the temperature of heat source of 50 W is kept at 60°C or less. In general, CPU is usually used at this temperature or less.

Feasibility Study on Cutting HTPB Propellants with Abrasive Water Jet

Science.gov (United States)

Jiang, Dayong; Bai, Yun

2018-01-01

Abrasive water jet is used to carry out the experiment research on cutting HTPB propellants with three components, which will provide technical support for the engineering treatment of waste rocket motor. Based on the reliability theory and related scientific research results, the safety and efficiency of cutting sensitive HTPB propellants by abrasive water jet were experimentally studied. The results show that the safety reliability is not less than 99.52% at 90% confidence level, so the safety is adequately ensured. The cooling and anti-friction effect of high-speed water jet is the decisive factor to suppress the detonation of HTPB propellant. Compared with pure water jet, cutting efficiency was increased by 5% - 87%. The study shows that abrasive water jets meet the practical use for cutting HTPB propellants.

Simulation and material testing of jet engines

International Nuclear Information System (INIS)

Tariq, M.M.

2006-01-01

The NASA software engine simulator version U 1.7a beta has been used for simulation and material testing of jet engines. Specifications of Modem Jet Engines are stated, and then engine simulator is applied on these specifications. This simulator can simulate turbojet, afterburner, turbofan and ram jet. The material of many components of engine may be varied. Conventional and advanced materials for jet engines can be simulated and tested. These materials can be actively cooled to increase the operating temperature limit. As soon as temperature of any engine component exceeds the temperature limit of material, a warning message flashes across screen. Temperature Limits Exceeded. This flashing message remainst here until necessaryc hangesa re carried out in engine operationp rocedure. Selection Criteria of Engines is stated for piston prop, turboprop, turbofan, turbojet, and turbojet with afterburner and Ramjet. Several standard engines are modeled in Engine Simulator. These engines can. be compared by several engineering specifications. The design, modeling, simulation and testing of engines helps to better understand different types of materials used in jet engines. (author)

Clock Technology Development for the Laser Cooling and Atomic Physics (LCAP) Program

Science.gov (United States)

Klipstein, W. M.; Thompson, R. J.; Seidel, D. J.; Kohel, J.; Maleki, L.

1998-01-01

The Time and Frequency Sciences and Technology Group at Jet Propulsion Laboratory (JPL) has developed a laser cooling capability for flight and has been selected by NASA to support the Laser-Cooling and Atomic Physics (LCAP) program. Current work in the group includes design and development for tee two laser-cooled atomic clock experiments which have been selected for flight on the International Space Station.

1.5 °C ? - Solutions for avoiding catastrophic climate change in this century

Science.gov (United States)

Xu, Y.

2017-12-01

The historic Paris Agreement calls for limiting global temperature rise to "well below 2 °C." Because of uncertainties in emission scenarios, climate, and carbon cycle feedback, we interpret the Paris Agreement in terms of three climate risk categories and bring in considerations of low-probability (5%) high impact (LPHI) warming in addition to the central (˜50% probability) value. The current risk category of dangerous warming is extended to more categories, which are defined by us here as follows: >1.5 °C as dangerous; >3 °C as catastrophic; and >5 °C as unknown, implying beyond catastrophic, including existential threats. With unchecked emissions, the central warming can reach the dangerous level within three decades, with the LPHI warming becoming catastrophic by 2050. We outline a three-lever strategy to limit the central warming below the dangerous level and the LPHI below the catastrophic level, both in the near term (pollutant (SP) lever to mitigate short-lived climate pollutants, and the carbon extraction and sequestration (CES) lever to thin the atmospheric CO2 blanket. Pulling on both CN and SP levers and bending the emissions curve by 2020 can keep the central warming below dangerous levels. To limit the LPHI warming below dangerous levels, the CES lever must be pulled as well to extract as much as 1 trillion tons of CO2 before 2100 to both limit the preindustrial to 2100 cumulative net CO2 emissions to 2.2 trillion tons and bend the warming curve to a cooling trend. In addition to present the analysis above, I will also share (1) perspective on developed and developing world actions and interactions on climate solutions; (2) Prof V. Ramanathan's interactions with the Pontifical Academy of Sciences and other religious groups which are highly valuable to the interdisciplinary audience.

Evaluation of water cooled supersonic temperature and pressure probes for application to 1366 K flows

Science.gov (United States)

Lagen, Nicholas; Seiner, John M.

1990-01-01

Water cooled supersonic probes are developed to investigate total pressure, static pressure, and total temperature in high-temperature jet plumes and thereby determine the mean flow properties. Two probe concepts, designed for operation at up to 1366 K in a Mach 2 flow, are tested on a water cooled nozzle. The two probe designs - the unsymmetric four-tube cooling configuration and the symmetric annular cooling design - take measurements at 755, 1089, and 1366 K of the three parameters. The cooled total and static pressure readings are found to agree with previous test results with uncooled configurations. The total-temperature probe, however, is affected by the introduction of water coolant, and effect which is explained by the increased heat transfer across the thermocouple-bead surface. Further investigation of the effect of coolant on the temperature probe is proposed to mitigate the effect and calculate more accurate temperatures in jet plumes.

Radial velocity asymmetries from jets with variable velocity profiles

International Nuclear Information System (INIS)

Cerqueira, A. H.; Vasconcelos, M. J.; Velazquez, P. F.; Raga, A. C.; De Colle, F.

2006-01-01

We have computed a set of 3-D numerical simulations of radiatively cooling jets including variabilities in both the ejection direction (precession) and the jet velocity (intermittence), using the Yguazu-a code. In order to investigate the effects of jet rotation on the shape of the line profiles, we also introduce an initial toroidal rotation velocity profile. Since the Yguazu-a code includes an atomic/ionic network, we are able to compute the emission coefficients for several emission lines, and we generate line profiles for the Hα, [O I]λ6300, [S II]λ6716 and [N II]λ6548 lines. Using initial parameters that are suitable for the DG Tau microjet, we show that the computed radial velocity shift for the medium-velocity component of the line profile as a function of distance from the jet axis is strikingly similar for rotating and non-rotating jet models

Development of a higher power cooling system for lithium targets.

Science.gov (United States)

Phoenix, B; Green, S; Scott, M C; Bennett, J R J; Edgecock, T R

2015-12-01

The accelerator based Boron Neutron Capture Therapy beam at the University of Birmingham is based around a solid thick lithium target cooled by heavy water. Significant upgrades to Birmingham's Dynamitron accelerator are planned prior to commencing a clinical trial. These upgrades will result in an increase in maximum achievable beam current to at least 3 mA. Various upgrades to the target cooling system to cope with this increased power have been investigated. Tests of a phase change coolant known as "binary ice" have been carried out using an induction heater to provide a comparable power input to the Dynamitron beam. The experimental data shows no improvement over chilled water in the submerged jet system, with both systems exhibiting the same heat input to target temperature relation for a given flow rate. The relationship between the cooling circuit pumping rate and the target temperature in the submerged jet system has also been tested. Copyright © 2015 Elsevier Ltd. All rights reserved.

The development of air cooled condensation systems

International Nuclear Information System (INIS)

Bodas, J.

1990-01-01

EGI - Contracting/Engineering has had experience with the development of air cooled condensing systems since the 1950's. There are two accepted types of dry cooling systems,the direct and the indirect ones. Due to the fact that the indirect system has several advantages over the direct one, EGI's purpose was to develop an economic, reliable and efficient type of indirect cooling system, both for industrial and power station applications. Apart from system development, the main components of dry cooling plant have been developed as well. These are: the water-to-air heat exchangers; the direct contact (DC, or jet) condenser; the cooling water circulating pumps and recovery turbines; and the peak cooling/preheating units. As a result of this broad development work which was connected with intensive market activity, EGI has supplied about 50% of the dry cooling plants employed for large power stations all over the world. This means that today the cumulated capacity of power units using Heller type dry cooling systems supplied and contracted by EGI is over 6000 MW

Emergency cooling system for a liquid metal cooled reactor

International Nuclear Information System (INIS)

Murata, Ryoichi; Fujiwara, Toshikatsu.

1980-01-01

Purpose: To suitably cool liquid metal as coolant in emergency in a liquid metal cooled reactor by providing a detector for the pressure loss of the liquid metal passing through a cooling device in a loop in which the liquid metal is flowed and communicating the detector with a coolant flow regulator. Constitution: A nuclear reactor is stopped in nuclear reaction by control element or the like in emergency. If decay heat is continuously generated for a while and secondary coolant is insufficiently cooled with water or steam flowed through a steam and water loop, a cooler is started. That is, low temperature air is supplied by a blower through an inlet damper to the cooler to cool the secondary coolant flowed into the cooler through a bypass pipe so as to finally safely stop an entire plant. Since the liquid metal is altered in its physical properties by the temperature at this time, it is detected to regulate the opening of the valve of the damper according to the detected value. (Sekiya, K.)

Socio-economic consequences of Chernobyl catastrophe. Social protection of the citizens, affected owing to Chernobyl catastrophe

International Nuclear Information System (INIS)

Kholosha, V.; Kovalchuk, V.

2003-01-01

The accident on Chernobyl NPP has affected the destiny of 35 million people in Ukraine. The social protection of the population affected during Chernobyl catastrophe is founded on the Law of Ukraine 'About the status and social protection of citizens affected owing to Chernobyl catastrophe' (see further - 'Law'), and is the principal direction of activity and the subject of the special state attention to total complex of problems bound to Chernobyl catastrophe consequences elimination. The current legislation stipulates partial compensation of material losses connected with resettlement of the affected population. According to the current legislation in Ukraine about 50 kinds of aid, privileges and compensations are submitted to the affected citizens

Water jet behavior in center water jet type supersonic steam injector

International Nuclear Information System (INIS)

Kawamoto, Y.; Abe, Y.

2005-01-01

Next-generation reactor systems have been under development aiming at simplified system and improvement of safety and credibility. A steam injector has a function of a passive pump without large motor or turbo-machinery, and has been investigated as one of the most important component of the next-generation reactor. Its performance as a pump depends on direct contact condensation phenomena between a supersonic steam and a sub-cooled water jet. As previous studies of the steam injector, there are studies about formulation of operating characteristic of steam injector and analysis of jet structure in steam injector by Narabayashi etc. And as previous studies of the direct contact condensation, there is the study about the direct contact condensation in steam atmosphere. However the study about the turbulent heat transfer under the great shear stress is not enough investigated. Therefore it is necessary to examine in detail about the operating characteristic of the steam injector. The present paper reports the observation results of the water jet behavior in the super sonic steam injector by using the video camera and the high-speed video camera. And the measuring results of the temperature and the pressure distribution in the steam injector are reported. From observation results by video camera, it is cleared that the water jet is established at the center of the steam injector right after steam supplied and the operation of the steam injector depends on the throat diameter. And from observation results by high-speed video camera, it is supposed that the columned water jet surface is established in the mixing nozzle and the water jet surface movement exists. Furthermore and effect of the non-condensable gas on the steam injector is investigated by measuring the radial temperature distributions in the water jet. From measuring results, it is supposed the more the air included in the steam, the more the temperature fluctuation of both steam and discharge water

Gasdynamic structure of free argon plasma jet

International Nuclear Information System (INIS)

Dunder, J.

1973-01-01

The paper deals with the experimental results of research conducted on the argon plasma jet. Special miniaturized water cooled Pitot probes (1.45 and 2.5 mm. dia.) were used for the measurement of the total head. The results correlate the length of the arc chamber and other main parameters of the plasma generator with the length of the core and maximum values of the total pressure and velocity in the core of the jet. For the plasma generator used for the experiments the axial and radial distributions of the pressure as well as the generalized volt-ampere dependence were obtained. (author)

New cooling regulation technology of secondary cooling station in DCS

Energy Technology Data Exchange (ETDEWEB)

Zhou, Xuan; Yan, Jun-wei; Zhu, Dong-sheng; Liu, Fei-long; Lei, Jun-xi [The Key Lab of Enhanced Heat Transfer and Energy Conservation of Ministry of Education, School of Chemical and Energy Engineering, South China University of Technology, Guangzhou 510641 (China); Liang, Lie-quan [The Key Lab of E-Commerce Market Application Technology of Guangdong Province, Guangdong University of Business Studies, Guangzhou 510320 (China)

2008-07-01

In this paper, a kind of new control technology of secondary cooling station (constant flow rate/variable temperature difference) in district cooling system (DCS) is proposed in view of serial consequences including low efficiency and high operating cost caused by low temperature of supply water in DCS. This technology has been applied in DCS of Guangzhou University City. The result has already indicated that such technology can increase the supply and return temperatures of buildings, return water temperature of primary side in the plate heat exchanger unit, moreover, the efficiency of both the chiller and the whole system are improved significantly. (author)

Multiple Sclerosis and Catastrophic Health Expenditure in Iran.

Science.gov (United States)

Juyani, Yaser; Hamedi, Dorsa; Hosseini Jebeli, Seyede Sedighe; Qasham, Maryam

2016-09-01

There are many disabling medical conditions which can result in catastrophic health expenditure. Multiple Sclerosis is one of the most costly medical conditions through the world which encounter families to the catastrophic health expenditures. This study aims to investigate on what extent Multiple sclerosis patients face catastrophic costs. This study was carried out in Ahvaz, Iran (2014). The study population included households that at least one of their members suffers from MS. To analyze data, Logit regression model was employed by using the default software STATA12. 3.37% of families were encountered with catastrophic costs. Important variables including brand of drug, housing, income and health insurance were significantly correlated with catastrophic expenditure. This study suggests that although a small proportion of MS patients met the catastrophic health expenditure, mechanisms that pool risk and cost (e.g. health insurance) are required to protect them and improve financial and access equity in health care.

Revisiting the EC/CMB model for extragalactic large scale jets

Science.gov (United States)

Lucchini, M.; Tavecchio, F.; Ghisellini, G.

2017-04-01

One of the most outstanding results of the Chandra X-ray Observatory was the discovery that AGN jets are bright X-ray emitters on very large scales, up to hundreds of kpc. Of these, the powerful and beamed jets of flat-spectrum radio quasars are particularly interesting, as the X-ray emission cannot be explained by an extrapolation of the lower frequency synchrotron spectrum. Instead, the most common model invokes inverse Compton scattering of photons of the cosmic microwave background (EC/CMB) as the mechanism responsible for the high-energy emission. The EC/CMB model has recently come under criticism, particularly because it should predict a significant steady flux in the MeV-GeV band which has not been detected by the Fermi/LAT telescope for two of the best studied jets (PKS 0637-752 and 3C273). In this work, we revisit some aspects of the EC/CMB model and show that electron cooling plays an important part in shaping the spectrum. This can solve the overproduction of γ-rays by suppressing the high-energy end of the emitting particle population. Furthermore, we show that cooling in the EC/CMB model predicts a new class of extended jets that are bright in X-rays but silent in the radio and optical bands. These jets are more likely to lie at intermediate redshifts and would have been missed in all previous X-ray surveys due to selection effects.

An Evolving Compact Jet in the Black Hole X-Ray Binary Maxi J1836-194

Science.gov (United States)

Russell, D. M.; Russell, T. D.; Miller-Jones, J. C. A.; O'Brien, K.; Soria, R.; Sivakoff, G. R.; Slaven-Blair, T.; Lewis, F.; Markoff, S.; Homan, J.;

Peculiar variable star R Aquarii and its jet

Energy Technology Data Exchange (ETDEWEB)

Kafatos, M; Michalitsianos, A G [National Aeronautics and Space Administration, Greenbelt, MD (USA). Goddard Space Flight Center

1982-08-05

The formation of a jet from the central star in the symbiotic variable R Aquarii is discussed and it is suggested that it is the result of supercritical accretion of mass transferred from the cool 387-day period Mira to the hot companion in a highly elliptical orbit. Ancient Japanese astronomical records suggest a nova outburst in AD930 may be associated with R Aquarii which formed the outer extended nebulosity. It is considered that the jet may help explain the outbursts of this object as well as the excitation of the R Aquarii nebula.

Cooled heavy ion beams at the ESR

International Nuclear Information System (INIS)

Steck, M.; Beckert, K.; Bosch, F.; Eickhoff, H.; Franzke, B.; Klepper, O.; Nolden, F.; Reich, H.; Schlitt, B.; Spaedtke, P.; Winkler, T.

1996-01-01

The storage ring ESR has been used in various operational modes for experiments with electron cooled heavy ion beams. Besides the standard storage mode including injection and beam accumulation the deceleration of highly charged ions has been demonstrated. Beams of highly charged ions have been injected and accumulated and finally decelerated to a minimum energy of 50 MeV/u. An ultraslow extraction method using charge changing processes is now also available for cooled beams of highly charged ions. For in ring experiments the internal gas jet and the cold electron beam of the cooling system are applied as targets. High precision mass spectrometry by Schottky noise detection has been demonstrated. Operation at transition energy has been achieved with cooled beams opening the field for experiments which require an isochronous revolution of the ions. (orig.)

DOWNWARD CATASTROPHE OF SOLAR MAGNETIC FLUX ROPES

Energy Technology Data Exchange (ETDEWEB)

Zhang, Quanhao; Wang, Yuming; Hu, Youqiu; Liu, Rui, E-mail: zhangqh@mail.ustc.edu.cn [CAS Key Laboratory of Geospace Environment, Department of Geophysics and Planetary Sciences, University of Science and Technology of China, Hefei 230026 (China)

2016-07-10

2.5-dimensional time-dependent ideal magnetohydrodynamic (MHD) models in Cartesian coordinates were used in previous studies to seek MHD equilibria involving a magnetic flux rope embedded in a bipolar, partially open background field. As demonstrated by these studies, the equilibrium solutions of the system are separated into two branches: the flux rope sticks to the photosphere for solutions at the lower branch but is suspended in the corona for those at the upper branch. Moreover, a solution originally at the lower branch jumps to the upper, as the related control parameter increases and reaches a critical value, and the associated jump is here referred to as an upward catastrophe. The present paper advances these studies in three aspects. First, the magnetic field is changed to be force-free; the system still experiences an upward catastrophe with an increase in each control parameter. Second, under the force-free approximation, there also exists a downward catastrophe, characterized by the jump of a solution from the upper branch to the lower. Both catastrophes are irreversible processes connecting the two branches of equilibrium solutions so as to form a cycle. Finally, the magnetic energy in the numerical domain is calculated. It is found that there exists a magnetic energy release for both catastrophes. The Ampère's force, which vanishes everywhere for force-free fields, appears only during the catastrophes and does positive work, which serves as a major mechanism for the energy release. The implications of the downward catastrophe and its relevance to solar activities are briefly discussed.

DOWNWARD CATASTROPHE OF SOLAR MAGNETIC FLUX ROPES

International Nuclear Information System (INIS)

Zhang, Quanhao; Wang, Yuming; Hu, Youqiu; Liu, Rui

2016-01-01

2.5-dimensional time-dependent ideal magnetohydrodynamic (MHD) models in Cartesian coordinates were used in previous studies to seek MHD equilibria involving a magnetic flux rope embedded in a bipolar, partially open background field. As demonstrated by these studies, the equilibrium solutions of the system are separated into two branches: the flux rope sticks to the photosphere for solutions at the lower branch but is suspended in the corona for those at the upper branch. Moreover, a solution originally at the lower branch jumps to the upper, as the related control parameter increases and reaches a critical value, and the associated jump is here referred to as an upward catastrophe. The present paper advances these studies in three aspects. First, the magnetic field is changed to be force-free; the system still experiences an upward catastrophe with an increase in each control parameter. Second, under the force-free approximation, there also exists a downward catastrophe, characterized by the jump of a solution from the upper branch to the lower. Both catastrophes are irreversible processes connecting the two branches of equilibrium solutions so as to form a cycle. Finally, the magnetic energy in the numerical domain is calculated. It is found that there exists a magnetic energy release for both catastrophes. The Ampère's force, which vanishes everywhere for force-free fields, appears only during the catastrophes and does positive work, which serves as a major mechanism for the energy release. The implications of the downward catastrophe and its relevance to solar activities are briefly discussed.

Flow transition criteria of a liquid jet into a liquid pool

Energy Technology Data Exchange (ETDEWEB)

Saito, Shimpei, E-mail: s1630195@u.tsukuba.ac.jp [Graduate School of Systems and Information Engineering, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8573 (Japan); Abe, Yutaka [Faculty of Engineering, Information and Systems, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8573 (Japan); Koyama, Kazuya [Reactor Core and Safety Design Department, Mitsubishi FBR Systems, Inc., 2-34-17 Jingumae, Shibuya, Tokyo 150-0001 (Japan)

2017-04-15

Highlights: • Jet breakup and droplet formation in immiscible liquid-liquid systems was studied experimentally. • The observed jet breakup behavior was classified into characteristic regimes. • The droplet size distribution was analyzed using image processing. • The variation of droplet size was compared with available melt-jet experiments. • Extrapolation to the expected SFR conditions implied that most of the hydrodynamic conditions would be the atomization regime. - Abstract: To better understand the fundamental interactions between melt jet and coolant during a core-disruptive accident at a sodium-cooled fast reactor, the jet breakup and droplet formation in immiscible liquid-liquid systems were studied experimentally. Experiments using two different pairs of test fluids were carried out at isothermal conditions. The observed jet breakup behavior was classified into characteristic regimes based on the classical Ohnesorge classification in liquid-gas systems. The variation in breakup length obtained in the present liquid-liquid system was similar to that in a liquid-gas system. The droplet size distribution in each breakup regime was analyzed using image processing and droplet formation via pinch-off, satellite formation, and entrainment was observed. The measured droplet size was compared with those available from melt jet experiments. Based on the observation and analysis results, the breakup regimes were organized on a dimensionless operating diagram, with the derived correlations representing the criteria for regime boundaries of a liquid-liquid system. Finally, the experimental data were extrapolated to the expected conditions of a sodium-cooled fast reactor. From this, it was implied that most of the hydrodynamic conditions during an accident would be close to the atomization regime, in which entrainment is the dominant process for droplet formation.

Catastrophic Antiphospholipid Syndrome

Directory of Open Access Journals (Sweden)

Rawhya R. El-Shereef

2016-01-01

Full Text Available This paper reports one case of successfully treated patients suffering from a rare entity, the catastrophic antiphospholipid syndrome (CAPS. Management of this patient is discussed in detail.

High-intensity, thin-target He-jet production source

International Nuclear Information System (INIS)

Bai, Y.; Vieira, D.J.; Wouters, J.M.; Butler, G.W.; Rosenauer, Dk; Loebner, K.E.G.; Lind, V.G.; Phillips, D.R.

1996-01-01

A thin-target He-jet system suited to the production and rapid transport of non-volatile radioactive species has been successfully operated with proton beam intensities of up to 700 μA. The system consists of a water-cooled, thin-target chamber, capillary gas transport system, moving tape/Ge detection system, and an aerosol generator/gas recirculator. The yields for a wide variety of uranium fission and deep spallation products have been measured and robust operation of the system demonstrated for several weeks. He-jet transport and collection efficiencies ranged between 15 and 25% with collection rates of 10 7 to 10 8 atoms/sec/isotope. The high-intensity, thin-target He-jet approach represents a robust production source for nonvolatile radioactive heavy ion beams

A Reconnection Switch to Trigger gamma-Ray Burst Jet Dissipation

International Nuclear Information System (INIS)

McKinney, Jonathan

2012-01-01

Prompt gamma-ray burst (GRB) emission requires some mechanism to dissipate an ultrarelativistic jet. Internal shocks or some form of electromagnetic dissipation are candidate mechanisms. Any mechanism needs to answer basic questions, such as what is the origin of variability, what radius does dissipation occur at, and how does efficient prompt emission occur. These mechanisms also need to be consistent with how ultrarelativistic jets form and stay baryon pure despite turbulence and electromagnetic reconnection near the compact object and despite stellar entrainment within the collapsar model. We use the latest magnetohydrodynamical models of ultrarelativistic jets to explore some of these questions in the context of electromagnetic dissipation due to the slow collisional and fast collisionless reconnection mechanisms, as often associated with Sweet-Parker and Petschek reconnection, respectively. For a highly magnetized ultrarelativistic jet and typical collapsar parameters, we find that significant electromagnetic dissipation may be avoided until it proceeds catastrophically near the jet photosphere at large radii (r ∼ 10 13 -10 14 cm), by which the jet obtains a high Lorentz factor (γ ∼ 100-1000), has a luminosity of L j ∼ 10 50 -10 51 erg s -1 , has observer variability timescales of order 1s (ranging from 0.001-10s), achieves γθ j ∼ 10-20 (for opening half-angle θ j ) and so is able to produce jet breaks, and has comparable energy available for both prompt and afterglow emission. A range of model parameters are investigated and simplified scaling laws are derived. This reconnection switch mechanism allows for highly efficient conversion of electromagnetic energy into prompt emission and associates the observed prompt GRB pulse temporal structure with dissipation timescales of some number of reconnecting current sheets embedded in the jet. We hope this work helps motivate the development of self-consistent radiative compressible relativistic

Catastrophe theory and its application status in mechanical engineering

Directory of Open Access Journals (Sweden)

Jinge LIU

Full Text Available Catastrophe theory is a kind of mathematical method which aims to apply and interpret the discontinuous phenomenon. Since its emergence, it has been widely used to explain a variety of emergent phenomena in the fields of natural science, social science, management science and some other science and technology fields. Firstly, this paper introduces the theory of catastrophe in several aspects, such as its generation, radical principle, basic characteristics and development. Secondly, it summarizes the main applications of catastrophe theory in the field of mechanical engineering, focusing on the research progress of catastrophe theory in revealing catastrophe of rotor vibration state, analyzing friction and wear failure, predicting metal fracture, and so on. Finally, it advises that later development of catastrophe theory should pay more attention to the combination of itself with other traditional nonlinear theories and methods. This paper provides a beneficial reference to guide the application of catastrophe theory in mechanical engineering and related fields for later research.

A self-regulating valve for single-phase liquid cooling of microelectronics

International Nuclear Information System (INIS)

Donose, Radu; De Volder, Michaël; Peirs, Jan; Reynaerts, Dominiek

2011-01-01

This paper reports on the design, optimization and testing of a self-regulating valve for single-phase liquid cooling of microelectronics. Its purpose is to maintain the integrated circuit (IC) at constant temperature and to reduce power consumption by diminishing flow generated by the pump as a function of the cooling requirements. It uses a thermopneumatic actuation principle that combines the advantages of zero power consumption and small size in combination with a high flow rate and low manufacturing costs. The valve actuation is provided by the thermal expansion of a liquid (actuation fluid) which, at the same time, actuates the valve and provides feed-back sensing. A maximum flow rate of 38 kg h −1 passes through the valve for a heat load up to 500 W. The valve is able to reduce the pumping power by up to 60% and it has the capability to maintain the IC at a more uniform temperature.

Extensional rheometer based on viscoelastic catastrophes outline

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to a method and a device for determining viscoelastic properties of a fluid. The invention resides inter alia in the generation of viscoelastic catastrophes in confined systems for use in the context of extensional rheology. The viscoelastic catastrophe is according ...... to the invention generated in a bistable fluid system, and the flow conditions for which the catastrophe occurs can be used as a fingerprint of the fluid's viscoelastic properties in extensional flow....

Laval nozzles for cluster-jet targets

Energy Technology Data Exchange (ETDEWEB)

Grieser, Silke; Bonaventura, Daniel; Hergemoeller, Ann-Katrin; Hetz, Benjamin; Koehler, Esperanza; Lessmann, Lukas; Khoukaz, Alfons [Institut fuer Kernphysik, Westfaelische Wilhelms-Universitaet Muenster, 48149 Muenster (Germany)

2016-07-01

Cluster-jet targets are highly suited for storage ring experiments due to the fact that they provide high and constant beam densities. Therefore, a cluster-jet target is planned to be the first internal target for the PANDA experiment at FAIR. A cluster source generates a continuous flow of cryogenic solid clusters by the expansion of pre-cooled gases within fine Laval nozzles. For the production of clusters the geometry of the nozzle is crucial. The production of such nozzles with their complex inner geometry represents a major technical challenge. The possibility to produce new fine Laval nozzles ensures the operation of cluster-jet targets, e.g. for the PANDA experiment, and opens the way for future investigations on the cluster production process to match the required targets performance. Optimizations on the recently developed production process and the fabrication of new glass nozzles were done. Initial measurements of these nozzles at the PANDA cluster-jet target prototype and the investigation of the cluster beam origin within the nozzle will be presented and discussed. For the future more Laval nozzles with different geometries will be produced and additional measurements with these new nozzles at the PANDA cluster-jet target prototype towards higher performance will be realized.

Design and testing of low-divergence elliptical-jet nozzles

Energy Technology Data Exchange (ETDEWEB)

Rouly, Etienne; Warkentin, Andrew; Bauer, Robert [Dalhousie University, Halifax (China)

2015-05-15

A novel approach was developed to design and fabricate nozzles to produce high-pressure low-divergence fluid jets. Rapid-prototype fabrication allowed for myriad experiments investigating effects of different geometric characteristics of nozzle internal geometry on jet divergence angle and fluid distribution. Nozzle apertures were elliptical in shape with aspect ratios between 1.00 and 2.45. The resulting nozzle designs were tested and the lowest elliptical jet divergence angle was 0.4 degrees. Nozzle pressures and flowrates ranged from 0.32 to 4.45 MPa and 13.6 to 37.9 LPM, respectively. CimCool CimTech 310 machining fluid was used in all experiments at a Brix concentration of 6.6 percent.

Mathematical Model of the Jet Engine Fuel System

Directory of Open Access Journals (Sweden)

Klimko Marek

2015-01-01

Full Text Available The paper discusses the design of a simplified mathematical model of the jet (turbo-compressor engine fuel system. The solution will be based on the regulation law, where the control parameter is a fuel mass flow rate and the regulated parameter is the rotational speed. A differential equation of the jet engine and also differential equations of other fuel system components (fuel pump, throttle valve, pressure regulator will be described, with respect to advanced predetermined simplifications.

Mathematical Model of the Jet Engine Fuel System

Science.gov (United States)

Klimko, Marek

2015-05-01

The paper discusses the design of a simplified mathematical model of the jet (turbo-compressor) engine fuel system. The solution will be based on the regulation law, where the control parameter is a fuel mass flow rate and the regulated parameter is the rotational speed. A differential equation of the jet engine and also differential equations of other fuel system components (fuel pump, throttle valve, pressure regulator) will be described, with respect to advanced predetermined simplifications.

Analysis of ex-vessel melt jet breakup and coolability. Part 1: Sensitivity on model parameters and accident conditions

Energy Technology Data Exchange (ETDEWEB)

Moriyama, Kiyofumi; Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr; Hwang, Byoungcheol; Jung, Woo Hyun

2016-06-15

Highlights: • Application of JASMINE code to melt jet breakup and coolability in APR1400 condition. • Coolability indexes for quasi steady state breakup and cooling process. • Typical case in complete breakup/solidification, film boiling quench not reached. • Significant impact of water depth and melt jet size; weak impact of model parameters. - Abstract: The breakup of a melt jet falling in a water pool and the coolability of the melt particles produced by such jet breakup are important phenomena in terms of the mitigation of severe accident consequences in light water reactors, because the molten and relocated core material is the primary heat source that governs the accident progression. We applied a modified version of the fuel–coolant interaction simulation code, JASMINE, developed at Japan Atomic Energy Agency (JAEA) to a plant scale simulation of melt jet breakup and cooling assuming an ex-vessel condition in the APR1400, a Korean advanced pressurized water reactor. Also, we examined the sensitivity on seven model parameters and five initial/boundary condition variables. The results showed that the melt cooling performance of a 6 m deep water pool in the reactor cavity is enough for removing the initial melt enthalpy for solidification, for a melt jet of 0.2 m initial diameter. The impacts of the model parameters were relatively weak and that of some of the initial/boundary condition variables, namely the water depth and melt jet diameter, were very strong. The present model indicated that a significant fraction of the melt jet is not broken up and forms a continuous melt pool on the containment floor in cases with a large melt jet diameter, 0.5 m, or a shallow water pool depth, ≤3 m.

On the cooling rate of strip cast ingots for sintered NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Yu, L.Q. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Yan, M. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)]. E-mail: mse_yanmi@dial.zju.edu.cn; Wu, J.M. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Luo, W. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Cui, X.G. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Ying, H.G. [State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310027 (China)

2007-04-30

Effects of the cooling rate of strip cast ingots on magnetic properties of sintered NdFeB magnets were studied. It is found that the magnetic properties greatly depend on wheel speed due to different alloy microstructures, which affect readily the particle size distribution of powders obtained after the subsequent jet milling. At higher cooling rate, interlamellar spacing between Nd-rich platelets of the alloy was small, resulting in a lower saturated magnetization due to increased amounts of small particles after jet milling. With further decreasing cooling rate, the resultant larger interlamellar spacing led to too large particle sizes as well as a more irregular shape; thus deteriorated the magnetic properties of the final magnet. A model was developed to disclose the effects of particle sizes on the magnetic alignment process. In the current investigation, optimum magnetic properties of the final magnets were obtained with a cooling rate of 2.6 m/s for preparing the strip. The magnets made by conventionally cast ingot technique exhibited the lowest magnetic properties because of the slowest cooling rate.

Runaway beam studies during disruptions at JET-ILW

International Nuclear Information System (INIS)

Reux, C.; Plyusnin, V.; Alper, B.; Alves, D.; Bazylev, B.; Belonohy, E.; Brezinsek, S.; Decker, J.; Devaux, S.; Vries, P. de; Fil, A.

2015-01-01

Highlights: • Runaway electrons (RE) have been obtained at JET-ILW using massive argon injection. • The runaway electron domain entry points are similar between JET-C and JET-ILW. • Inside the runaway electron domain, higher RE currents are observed with JET-ILW. • RE impact has been observed without material melting up to 100 kA RE current. • Heat deposition of 2 ± 1 mm is confirmed by measurements and simulations. - Abstract: Runaway electrons (RE) during disruptions are a concern for future tokamaks including ITER with its metallic wall. Although RE are rare in spontaneous disruptions with the JET ITER-like Wall (JET-ILW), RE beams up to 380 kA were obtained using massive injection (MGI) of argon in JET-ILW divertor discharges. Entry points into the RE domain defined by operational parameters (toroidal field, argon fraction in MGI) are unchanged but higher RE currents have been obtained inside the JET-ILW MGI-generated RE domain when compared to JET-C. This might be due to the influence of the metallic wall on the current quench plasma. Temperatures of 900 °C have been observed following RE impacts on beryllium tiles. Heat deposition depth of ∼2 mm has to be assumed to match the tile cooling time. 3D simulations of the RE energy deposition using the ENDEP/MEMOS codes show that material melting is unlikely with 100 kA RE beams

Runaway beam studies during disruptions at JET-ILW

Energy Technology Data Exchange (ETDEWEB)

Reux, C., E-mail: cedric.reux@cea.fr [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Plyusnin, V. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Instituto de Plasmas e Fuso Nuclear, Instituto Superior Tcnico, Universidade de Lisboa, Lisboa (Portugal); Alper, B. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CCFE, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Alves, D. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Instituto de Plasmas e Fuso Nuclear, Instituto Superior Tcnico, Universidade de Lisboa, Lisboa (Portugal); Bazylev, B. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Institut für Hochleistungsimpuls und Mikrowellentechnik, Karlsruhe Institute of Technology, Campus Nord, 76021 Karlsruhe (Germany); Belonohy, E. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); EFDA-CSU, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Brezinsek, S. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Forschungszentrum Jülich GmbH, Institut für Energie-und Klimaforschung-Plasmaphysik, 52425 Jülich (Germany); Decker, J. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Devaux, S. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CCFE, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Vries, P. de [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); ITER Organization, Route de Vinon sur Verdon, 13115 St Paul Lez Durance (France); Fil, A. [JET-EFDA, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); and others

2015-08-15

Highlights: • Runaway electrons (RE) have been obtained at JET-ILW using massive argon injection. • The runaway electron domain entry points are similar between JET-C and JET-ILW. • Inside the runaway electron domain, higher RE currents are observed with JET-ILW. • RE impact has been observed without material melting up to 100 kA RE current. • Heat deposition of 2 ± 1 mm is confirmed by measurements and simulations. - Abstract: Runaway electrons (RE) during disruptions are a concern for future tokamaks including ITER with its metallic wall. Although RE are rare in spontaneous disruptions with the JET ITER-like Wall (JET-ILW), RE beams up to 380 kA were obtained using massive injection (MGI) of argon in JET-ILW divertor discharges. Entry points into the RE domain defined by operational parameters (toroidal field, argon fraction in MGI) are unchanged but higher RE currents have been obtained inside the JET-ILW MGI-generated RE domain when compared to JET-C. This might be due to the influence of the metallic wall on the current quench plasma. Temperatures of 900 °C have been observed following RE impacts on beryllium tiles. Heat deposition depth of ∼2 mm has to be assumed to match the tile cooling time. 3D simulations of the RE energy deposition using the ENDEP/MEMOS codes show that material melting is unlikely with 100 kA RE beams.

JET pump limiter

International Nuclear Information System (INIS)

Sonnenberg, K.; Deksnis, E.; Shaw, R.; Reiter, D.

1988-01-01

JET plans to install two pump limiter modules which can be used for belt-limiter, inner-wall and X-point discharges and, also, for 1-2s as the main limiter. A design is presented which is compatible with two diagnostic systems, and which allows partial removal of the pump limiter to provide access for remote-handling operations. The high heat-flux components are initially cooled during a pulse. Heat is removed between discharges by radiation and pressure contacts to a water-cooled support structure. The pumping edge will be made of annealed pyrolytic graphite. Exhaust efficiency has been estimated, for a 1-d edge model, using a Monte-Carlo calculation of neutral gas transport. When the pump limiter is operated together with other wall components we expect an efficiency of ≅ 5% (2.5 x 10 21 part/s). As a main limiter the efficiency increases to about 10%. (author)

Fuel-coolant interactions in a jet contact mode

International Nuclear Information System (INIS)

Konishi, K.; Isozaki, M.; Imahori, S.; Kondo, S.; Furutani, A.; Brear, D.J.

1994-01-01

Molten fuel-coolant interactions in a jet contact mode was studied with respect to the safety of liquid-metal-cooled fast reactors (LMFRs). From a series of molten Wood's metal (melting point: 79 deg. C, density: -8400 kg/m 3 ) jet-water interaction experiments, several distinct modes of interaction behaviors were observed for various combinations of initial temperature conditions of the two fluids. A semi-empirical model for a minimum film boiling temperature criterion was developed and used to reasonably explain the different interaction modes. It was concluded that energetic jet-water interactions are only possible under relatively narrow initial thermal conditions. Preliminary extrapolation of the present results in an oxide fuel-sodium system suggests that mild interactions with short breakup length and coolable debris formation should be most likely in LMFRs. (author)

PARAMETRIC INSURANCE COVER FOR NATURAL CATASTROPHE RISKS

Directory of Open Access Journals (Sweden)

Serghei Margulescu

2013-11-01

Full Text Available With economic losses of over USD 370 bn caused by 325 catastrophic events, 2011 ranks as the worst ever year in terms of costs to society due to natural catastrophes and man-made disasters. Inthe same time, 2011 is the second most expensive year in the history for the insurance industry, with insured losses from catastrophic events amounting to USD 116 bn. Both the high level of damages and insured losses, as well as the unprecedented gap between the two values, made insurers and reinsurers worldwide to understand that some risks had so far been underestimated and they have to be better integrated in the catastrophes modelling.On the other hand, governments have to protect themselves against the financial impact of natural catastrophes and new forms of cooperation between the public and private sectors can help countries finance disaster risks. Viewed in a country’s wider risk management context, the purchase of parametric insurance cover, which transfers natural catastrophe risk to the private sector using an index- based trigger, is a necessary shift towards a pre-emptive risk management strategy. This kind of approach can be pursued by central governments or at the level of provincial or municipal governments, and a number of case studies included in the publication “Closing the financial gap” by Swiss Re (2011 illustrates how new forms of parametric insurance can help countries finance disaster risks.

Acoustic signature analysis of the interaction between a dc plasma jet and a suspension liquid jet

International Nuclear Information System (INIS)

Rat, V; Coudert, J F

2009-01-01

Suspension plasma spraying allows forming finely structured coatings by injecting suspensions of ceramic particles within a dc plasma jet. The electric arc motion in dc plasma torch is the main acoustic source which is modified by the injection of suspension. The analyses of cross-correlations between the arc voltage and the acoustic signal show a decrease in time propagations due to local cooling of the plasma jet when injecting suspensions. Moreover, power spectra highlight acoustic amplifications below a certain frequency threshold and attenuations above. A simplified model of the frequency acoustic response of a two-phase vaporizing mixture is used to interpret experimental measurements. These acoustic effects are due to the dynamics of thermal transfers between vaporizing liquid and plasma.

PIV measurements of turbulent jet and pool mixing produced by a steam jet discharge in a subcooled water pool

International Nuclear Information System (INIS)

Choo, Yeon Jun; Song, Chul-Hwa

2010-01-01

This experimental research is on the fluid-dynamic features produced by a steam injection into a subcooled water pool. The relevant phenomena could often be encountered in water cooled nuclear power plants. Two major topics, a turbulent jet and the internal circulation produced by a steam injection, were investigated separately using a particle image velocimetry (PIV) as a non-intrusive optical measurement technique. Physical domains of both experiments have a two-dimensional axi-symmetric geometry of which the boundary and initial conditions can be readily and well defined. The turbulent jet experiments with the upward discharging configuration provide the parametric values for quantitatively describing a turbulent jet such as the self-similar velocity profile, central velocity decay, spreading rate, etc. And in the internal circulation experiments with the downward discharging configuration, typical flow patterns in a whole pool region are measured in detail, which reveals both the local and macroscopic characteristics of the mixing behavior in a pool. This quantitative data on the condensing jet-induced mixing behavior in a pool could be utilized as benchmarking for a CFD simulation of relevant phenomena.

The impact of climate change on catastrophe risk models : implications for catastrophe risk markets in developing countries

OpenAIRE

Seo, John; Mahul, Olivier

2009-01-01

Catastrophe risk models allow insurers, reinsurers and governments to assess the risk of loss from catastrophic events, such as hurricanes. These models rely on computer technology and the latest earth and meteorological science information to generate thousands if not millions of simulated events. Recently observed hurricane activity, particularly in the 2004 and 2005 hurricane seasons, i...

Improvement and test calculation on basic code or sodium-water reaction jet

Energy Technology Data Exchange (ETDEWEB)

Saito, Yoshinori; Itooka, Satoshi [Advanced Reactor Engineering Center, Hitachi Works, Hitachi Ltd., Hitachi, Ibaraki (Japan); Okabe, Ayao; Fujimata, Kazuhiro; Sakurai, Tomoo [Consulting Engineering Dept., Hitachi Engineering Co., Ltd., Hitachi, Ibaraki (Japan)

1999-03-01

In selecting the reasonable DBL (design basis water leak rate) on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on the basic code for sodium-water reaction (SWR) jet was performed for an actual scale SG. The improvement points of the code are as follows; (1) introduction of advanced model such as heat transfer between the jet and structure (tube array), cooling effect of the structure, heat transfer between analytic cells, and (2) model improvement for heat transfer between two-phase flow and porous-media. The test calculation using the improved code (LEAP-JET ver.1.30) were carried out with conditions of the SWAT-3{center_dot}Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results is reasonable and Influence to analysis result of a model. Code integration with the blow down analytic code (LEAP-BLOW) was also studied. It is suitable that LEAP-JET was improved as one of the LEAP-BLOW's models, and it was integrated into this. In addition to above, the improvement for setting of boundary condition and the development of the interface program to transfer the analytical results of LEAP-BLOW have been performed in order to consider the cooling effect of coolant in the tube simply. However, verification of the code by new SWAT-1 and SWAT-3 test data planned in future is necessary because LEAP-JET is under development. And furthermore advancement needs to be planned. (author)

Improvement and test calculation on basic code or sodium-water reaction jet

International Nuclear Information System (INIS)

Saito, Yoshinori; Itooka, Satoshi; Okabe, Ayao; Fujimata, Kazuhiro; Sakurai, Tomoo

1999-03-01

In selecting the reasonable DBL (design basis water leak rate) on steam generator (SG), it is necessary to improve analytical method for estimating the sodium temperature on failure propagation due to overheating. Improvement on the basic code for sodium-water reaction (SWR) jet was performed for an actual scale SG. The improvement points of the code are as follows; (1) introduction of advanced model such as heat transfer between the jet and structure (tube array), cooling effect of the structure, heat transfer between analytic cells, and (2) model improvement for heat transfer between two-phase flow and porous-media. The test calculation using the improved code (LEAP-JET ver.1.30) were carried out with conditions of the SWAT-3·Run-19 test and an actual scale SG. It is confirmed that the SWR jet behavior on the results is reasonable and Influence to analysis result of a model. Code integration with the blow down analytic code (LEAP-BLOW) was also studied. It is suitable that LEAP-JET was improved as one of the LEAP-BLOW's models, and it was integrated into this. In addition to above, the improvement for setting of boundary condition and the development of the interface program to transfer the analytical results of LEAP-BLOW have been performed in order to consider the cooling effect of coolant in the tube simply. However, verification of the code by new SWAT-1 and SWAT-3 test data planned in future is necessary because LEAP-JET is under development. And furthermore advancement needs to be planned. (author)

Manipulation of pain catastrophizing: An experimental study of healthy participants

Directory of Open Access Journals (Sweden)

Joel E Bialosky

2008-11-01

Full Text Available Joel E Bialosky1*, Adam T Hirsh2,3, Michael E Robinson2,3, Steven Z George1,3*1Department of Physical Therapy; 2Department of Clinical and Health Psychology; 3Center for Pain Research and Behavioral Health, University of Florida, Gainesville, Florida, USAAbstract: Pain catastrophizing is associated with the pain experience; however, causation has not been established. Studies which specifically manipulate catastrophizing are necessary to establish causation. The present study enrolled 100 healthy individuals. Participants were randomly assigned to repeat a positive, neutral, or one of three catastrophizing statements during a cold pressor task (CPT. Outcome measures of pain tolerance and pain intensity were recorded. No change was noted in catastrophizing immediately following the CPT (F(1,84 = 0.10, p = 0.75, partial η2 < 0.01 independent of group assignment (F(4,84 = 0.78, p = 0.54, partial η2 = 0.04. Pain tolerance (F(4 = 0.67, p = 0.62, partial η2 = 0.03 and pain intensity (F(4 = 0.73, p = 0.58, partial η2 = 0.03 did not differ by group. This study suggests catastrophizing may be difficult to manipulate through experimental pain procedures and repetition of specific catastrophizing statements was not sufficient to change levels of catastrophizing. Additionally, pain tolerance and pain intensity did not differ by group assignment. This study has implications for future studies attempting to experimentally manipulate pain catastrophizing.Keywords: pain, catastrophizing, experimental, cold pressor task, pain catastrophizing scale

Valuing Catastrophe Bonds Involving Credit Risks

Directory of Open Access Journals (Sweden)

Jian Liu

2014-01-01

Full Text Available Catastrophe bonds are the most important products in catastrophe risk securitization market. For the operating mechanism, CAT bonds may have a credit risk, so in this paper we consider the influence of the credit risk on CAT bonds pricing that is different from the other literature. We employ the Jarrow and Turnbull method to model the credit risks and get access to the general pricing formula using the Extreme Value Theory. Furthermore, we present an empirical pricing study of the Property Claim Services data, where the parameters in the loss function distribution are estimated by the MLE method and the default probabilities are deduced by the US financial market data. Then we get the catastrophe bonds value by the Monte Carlo method.

Does catastrophic thinking enhance oesophageal pain sensitivity?

DEFF Research Database (Denmark)

Martel, M O; Olesen, A E; Jørgensen, D

2016-01-01

that catastrophic thinking exerts an influence on oesophageal pain sensitivity, but not necessarily on the magnitude of acid-induced oesophageal sensitization. WHAT DOES THIS STUDY ADD?: Catastrophizing is associated with heightened pain sensitivity in the oesophagus. This was substantiated by assessing responses...

Self-Efficacy for Pain Communication Moderates the Relation Between Ambivalence Over Emotional Expression and Pain Catastrophizing Among Patients With Osteoarthritis.

Science.gov (United States)

Van Denburg, Alyssa N; Shelby, Rebecca A; Caldwell, David S; O'Sullivan, Madeline L; Keefe, Francis J

2018-04-06

Pain catastrophizing (ie, the tendency to focus on and magnify pain sensations and feel helpless in the face of pain) is one of the most important and consistent psychological predictors of the pain experience. The present study examined, in 60 patients with osteoarthritis pain who were married or partnered: 1) the degree to which ambivalence over emotional expression and negative network orientation were associated with pain catastrophizing, and 2) whether self-efficacy for pain communication moderated these relations. Hierarchical multiple linear regression analyses revealed a significant main effect for the association between ambivalence over emotional expression and pain catastrophizing; as ambivalence over emotional expression increased, the degree of pain catastrophizing increased. In addition, the interaction between ambivalence over emotional expression and self-efficacy for pain communication was significant, such that as self-efficacy for pain communication increased, the association between ambivalence over emotional expression and pain catastrophizing became weaker. Negative network orientation was not significantly associated with pain catastrophizing. Findings suggest that higher levels of self-efficacy for pain communication may help weaken the effects of ambivalence over emotional expression on pain catastrophizing. In light of these results, patients may benefit from interventions that target pain communication processes and emotion regulation. This article examines interpersonal processes involved in pain catastrophizing. This study has the potential to lead to better understanding of maladaptive pain coping strategies and possibly better prevention and treatment strategies. Copyright © 2018 The American Pain Society. Published by Elsevier Inc. All rights reserved.

The thermal interaction of a buoyant plume from a calandria tube with an oblique jet

Energy Technology Data Exchange (ETDEWEB)

Rossouw, D.J.; Atkins, M.D.; Beharie, K. [Nuclear Science Division, School of Mechanical & Aeronautical Engineering, University of the Witwatersrand, Johannesburg (South Africa); Kim, T., E-mail: tong.kim@wits.ac.za [Nuclear Science Division, School of Mechanical & Aeronautical Engineering, University of the Witwatersrand, Johannesburg (South Africa); Rhee, B.W.; Kim, H.T. [Severe Accident and PHWR Safety Research Division, Korea Atomic Energy Research Institute, Daejun (Korea, Republic of)

2016-12-15

Highlights: • A crucial role of relative orientation between mixed convection modes is observed. • The extent of thermal interaction strongly depends on the relative orientation. • Coolant flow is substantially diffused by a buoyant plume if counter-acting. • Slightly oblique coolant flow to the gravitational axis provides the best cooling. - Abstract: Severe reactor core damage may occur from fuel channel failure as a consequence of excessive heat emitted from calandria tubes (CTs) in a pressurised heavy water (D{sub 2}O) reactor (CANDU). The heating of the CTs is caused by creep deformation of the pressure tubes (PTs), which may be ballooning or sagging depending on the internal pressure of the PTs. The deformation of the pressure tube is due to overheating as a result of a loss-of-coolant accident (LOCA) and emergency core cooling system (ECCS) failure. To prevent the exacerbation of the LOCA, circulating D{sub 2}O in the moderator tank may be utilized by forming a secondary jet that externally cools the individual CTs. The buoyant plume develops around the CTs and interacts with the secondary jet at a certain oblique angle with respect to the gravitational axis, depending on the spatial location of the hot calandria tubes (or the hot reactor core region). This study reports on how the local and overall heat transfer characteristics on a calandria tube where the buoyant plume develops, are altered by the obliqueness of the external secondary jet (from a co-current jet to a counter-current jet) in a simplified configuration at the jet Reynolds number of Re{sub j} = 1500 for the Archimedes number of Ar{sub D} = 0.11 and Rayleigh number of Ra{sub D} = 1.6 × 10{sup 6} (modified Rayleigh number of 3.0 × 10{sup 7}).

Enhanced heat sink with geometry induced wall-jet

Energy Technology Data Exchange (ETDEWEB)

Hossain, Md. Mahamudul, E-mail: sohel0991@gmail.com; Tikadar, Amitav; Bari, Fazlul; Morshed, A. K. M. M. [Department of Mechanical Engineering Bangladesh University of Engineering and Technology, Dhaka-1000. Bangladesh (Bangladesh)

2016-07-12

Mini-channels embedded in solid matrix have already proven to be a very efficient way of electronic cooling. Traditional mini-channel heat sinks consist of single layer of parallel channels. Although mini-channel heat sink can achieve very high heat flux, its pumping requirement for circulating liquid through the channel increase very sharply as the flow velocity increases. The pumping requirements of the heat sink can be reduced by increasing its performance. In this paper a novel approach to increase the thermal performance of the mini-channel heat sink is proposed through geometry induced wall jet which is a passive technique. Geometric irregularities along the channel length causes abrupt pressure change between the channels which causes cross flow through the interconnections thus one channel faces suction and other channel jet action. This suction and jet action disrupts boundary layer causing enhanced heat transfer performance. A CFD model has been developed using commercially available software package FLUENT to evaluate the technique. A parametric study of the velocities and the effect of the position of the wall-jets have been performed. Significant reduction in thermal resistance has been observed for wall-jets, it is also observed that this reduction in thermal resistance is dependent on the position and shape of the wall jet.

Jetted GRBs, afterglows and SGRs from quark stars birth

CERN Document Server

Dar, Arnon

1999-01-01

Recent studies suggest that when cold nuclear matter is compressed to high nuclear densities, diquarks with spin zero and antisymmetric color wave function Bose condensate into a superfluid/superconducting state that is several times as dense. Various astrophysical phenomena may be explained by gravitational collapse of neutron stars (NSs) to (di)quark stars (QSs) as a result of a first order phase transition in NSs within $\\sim 10^{4}$ years after their birth in supernova explosions, when they cooled and spun down sufficiently (by magnetic braking ?). The gravitational energy release drives an explosion which may eject both highly relativistic narrowly collimated jets and a mildly relativistic ``spherical'' shell. The slow contraction/cooling of the remnant QSs can power soft gamma ray repeaters (SGRs) and anomalous X-ray pulsars (AXPs), without invoking a huge magnetic energy storage. The jets can produce the observed gamma ray bursts (GRBs) in distant galaxies when they happen to point in our direction and...

Medium scale fire tests of propane tanks to study the boiling liquid expanding vapour explosion (BLEVE) and transient two-phase jet release

Energy Technology Data Exchange (ETDEWEB)

Ye Zhifei

1994-07-01

A series of medium scale fire tests were conducted to study boiling liquid expanding vapour explosions (BLEVE) and transient jet releases resulting from thermally induced propane tank ruptures. The tests were conducted using commercial propane contained in automotive propane tanks with a capacity of ca 400 liters. The tanks were brought to failure using a combination of torch and pool fire impingement. Instrumentation was included to measure internal pressure, liquid, vapour and wall temperature distribution, tank and lading mass, external blast overpressure, and fireball thermal radiation. Video and still cameras were used to record the fireball and jet fire shapes and dimensions. Two different kinds of BLEVE failure were observed. For very weak tanks the BLEVE was a single step process where the rupture propagated rapidly along the length of the tank. The duration of these events was measured in milliseconds and it is suggested that the process is driven by the vapour space energy. The other type of BLEVE was a two step process where a crack would start in a weakened area, arrest in a stronger part of the tank, and then start again to end in catastrophic failure. Initial failure and jet type release results in violent boiling and pressure recovery in the tank, leading to restart of the crack and catastrophic failure. Time duration is measured in seconds, and is driven by energy stored in the liquid. A computer model was developed to simulate the transient jet release resulting from finite tank failures, and can predict transient mass flow, tank pressure decay, visible flame length and jet fire thermal radiation. 253 refs., 132 figs., 29 tabs.

Nationwide Enviro Jet PCB Decontamination Approval and Notifications under Title 40 of the Code of Federal Regulations (CFR) Section 761.79(h)

Science.gov (United States)

This page contains information about approvals and notifications for Enviro Jet to Decontaminate PCB-contaminated natural gas pipelines under Title 40 of the Code of Federal Regulations (CFR) Section 761.79(h)

Convective Heat Transfer Coefficients of Automatic Transmission Fluid Jets with Implications for Electric Machine Thermal Management: Preprint

Energy Technology Data Exchange (ETDEWEB)

Bennion, Kevin; Moreno, Gilberto

2015-09-29

Thermal management for electric machines (motors/ generators) is important as the automotive industry continues to transition to more electrically dominant vehicle propulsion systems. Cooling of the electric machine(s) in some electric vehicle traction drive applications is accomplished by impinging automatic transmission fluid (ATF) jets onto the machine's copper windings. In this study, we provide the results of experiments characterizing the thermal performance of ATF jets on surfaces representative of windings, using Ford's Mercon LV ATF. Experiments were carried out at various ATF temperatures and jet velocities to quantify the influence of these parameters on heat transfer coefficients. Fluid temperatures were varied from 50 degrees C to 90 degrees C to encompass potential operating temperatures within an automotive transaxle environment. The jet nozzle velocities were varied from 0.5 to 10 m/s. The experimental ATF heat transfer coefficient results provided in this report are a useful resource for understanding factors that influence the performance of ATF-based cooling systems for electric machines.

CATASTROPHIC EVENTS MODELING

Directory of Open Access Journals (Sweden)

Ciumas Cristina

2013-07-01

Full Text Available This paper presents the emergence and evolution of catastrophe models (cat models. Starting with the present context of extreme weather events and features of catastrophic risk (cat risk we’ll make a chronological illustration from a theoretical point of view of the main steps taken for building such models. In this way the importance of interdisciplinary can be observed. The first cat model considered contains three modules. For each of these indentified modules: hazard, vulnerability and financial losses a detailed overview and also an exemplification of a potential case of an earthquake that measures more than 7 on Richter scale occurring nowadays in Bucharest will be provided. The key areas exposed to earthquake in Romania will be identified. Then, based on past catastrophe data and taking into account present conditions of housing stock, insurance coverage and the population of Bucharest the impact will be quantified by determining potential losses. In order to accomplish this work we consider a scenario with data representing average values for: dwelling’s surface, location, finishing works. On each step we’ll make a reference to the earthquake on March 4 1977 to see what would happen today if a similar event occurred. The value of Bucharest housing stock will be determined taking firstly the market value, then the replacement value and ultimately the real value to quantify potential damages. Through this approach we can find the insurance coverage of potential losses and also the uncovered gap. A solution that may be taken into account by public authorities, for example by Bucharest City Hall will be offered: in case such an event occurs the impossibility of paying compensations to insured people, rebuilding infrastructure and public buildings and helping the suffering persons should be avoided. An actively public-private partnership should be created between government authorities, the Natural Disaster Insurance Pool, private

X-ray Jets in the CH Cyg Symbiotic System

Science.gov (United States)

Karovska, Margarita; Gaetz, T.; Lee, N.; Raymond, J.; Hack, W.; Carilli, C.

2009-09-01

Symbiotic binaries are interacting systems in which a compact stellar source accretes matter from the wind of the cool evolved companion. There are a few hundred symbiotic systems known today, but jet activity has been detected in only a few of them, including in CH Cyg. CH Cyg is a symbiotic system that has shown significant activity since the mid 1960s. Jets have been detected in optical and radio since 1984, and more recently in 2001 in X-rays using Chandra observations.In 2008 we carried out coordinated multi-wavelength observations of the CH Cyg system with Chandra, HST, and the VLA, in order to study the propagation and interaction with the circumbinary medium of the jet detected in 2001. We report here on the detection of the 2001 SE jet which has expanded in seven years from ˜350AU to ˜1400 AU. The apex of the loop delineating the region of interaction with the circumbinary matter is moving with a speed of ˜700 km/s. Assuming a linear expansion, the jet was launched during the 1999-2000 active phase. We also report on a detection of a powerful new jet in the SW direction, observed in X-ray, optical and radio wavelengths. The new jet has a multi-component structure including an inner jet and counter jet, and a SW component ending in several clumps extending up to a distance of about 750AU.

Jet observables without jet algorithms

Energy Technology Data Exchange (ETDEWEB)

Bertolini, Daniele; Chan, Tucker; Thaler, Jesse [Center for Theoretical Physics, Massachusetts Institute of Technology,Cambridge, MA 02139 (United States)

2014-04-02

We introduce a new class of event shapes to characterize the jet-like structure of an event. Like traditional event shapes, our observables are infrared/collinear safe and involve a sum over all hadrons in an event, but like a jet clustering algorithm, they incorporate a jet radius parameter and a transverse momentum cut. Three of the ubiquitous jet-based observables — jet multiplicity, summed scalar transverse momentum, and missing transverse momentum — have event shape counterparts that are closely correlated with their jet-based cousins. Due to their “local” computational structure, these jet-like event shapes could potentially be used for trigger-level event selection at the LHC. Intriguingly, the jet multiplicity event shape typically takes on non-integer values, highlighting the inherent ambiguity in defining jets. By inverting jet multiplicity, we show how to characterize the transverse momentum of the n-th hardest jet without actually finding the constituents of that jet. Since many physics applications do require knowledge about the jet constituents, we also build a hybrid event shape that incorporates (local) jet clustering information. As a straightforward application of our general technique, we derive an event-shape version of jet trimming, allowing event-wide jet grooming without explicit jet identification. Finally, we briefly mention possible applications of our method for jet substructure studies.

Forced draft wet cooling systems

International Nuclear Information System (INIS)

Daubert, A.; Caudron, L.; Viollet, P.L.

1975-01-01

The disposal of the heat released from a 1000MW power plant needs a natural draft tower of about 130m of diameter at the base, and 170m height, or a cooling system with a draft forced by about forty vans, a hundred meters in diameter, and thirty meters height. The plumes from atmospheric cooling systems form, in terms of fluid mechanics, hot jets in a cross current. They consist in complex flows that must be finely investigated with experimental and computer means. The study, currently being performed at the National Hydraulics Laboratory, shows that as far as the length and height of visible plumes are concerned, the comparison is favorable to some types of forced draft cooling system, for low and medium velocities, (below 5 or 6m/s at 10m height. Beyond these velocities, the forced draft sends the plume up to smaller heights, but the plume is generally more dilute [fr

From a Catastrophe Itself to Cata/strophic Reading. The Poetry of Charles Baudelaire in the Account of Jorge Semprúna L’écriture ou la vie

Directory of Open Access Journals (Sweden)

Judith Kasper

2015-01-01

Full Text Available This essay addresses the instable meaning of the term catastrophe over the course of history. The first part takes leave of the “the tiny fissures” in the continuous catastrophe noted by Walter Benjamin to develop a philology of the cata/strophe. This philology does not only register a given meaning (for instance, of the catastrophe, but intervenes actively as disruption. It insists on the strophe in the catastrophe, transforming catastrophe into cata/strophe that, in fatal situations, permits the poetic potential to become a dynamic force that can, at least on the linguistic level, open toward other dimensions without denying the catastrophe itself. The second part is dedicated to a reading of Jorge Semprún’s autobiographical novel L’écriture ou la vie from the perspective of this philological concept. It seeks to show how Semprún’s citing and reciting of Baudelaire’s strophes in the putrid atmosphere of the Buchenwald concentration camp literally produce, on the level of the signifiers, fresh air to breathe.

A practical experience of using special remote handling tools on JET

International Nuclear Information System (INIS)

Mills, S.F.; Schreibmaier, J.; Tesini, A.; Wykes, M.

1987-01-01

Over 50 cutting and 200 UHV welding operations were made during the installation of new water cooled belt limiters and ICRF Antennae into the JET Vacuum Vessel. This work was performed by the hands-on use of 45 special tools which have been specifically designed for use with the Mascot servomanipulator in preparation for the JET D-T phase when all maintenance will be performed remotely. This paper reports on the techniques used and the performance of the tools. (author)

A Reconnection Switch to Trigger gamma-Ray Burst Jet Dissipation

Energy Technology Data Exchange (ETDEWEB)

McKinney, Jonathan C.; Uzdensky, Dmitri A.

2012-03-14

Prompt gamma-ray burst (GRB) emission requires some mechanism to dissipate an ultrarelativistic jet. Internal shocks or some form of electromagnetic dissipation are candidate mechanisms. Any mechanism needs to answer basic questions, such as what is the origin of variability, what radius does dissipation occur at, and how does efficient prompt emission occur. These mechanisms also need to be consistent with how ultrarelativistic jets form and stay baryon pure despite turbulence and electromagnetic reconnection near the compact object and despite stellar entrainment within the collapsar model. We use the latest magnetohydrodynamical models of ultrarelativistic jets to explore some of these questions in the context of electromagnetic dissipation due to the slow collisional and fast collisionless reconnection mechanisms, as often associated with Sweet-Parker and Petschek reconnection, respectively. For a highly magnetized ultrarelativistic jet and typical collapsar parameters, we find that significant electromagnetic dissipation may be avoided until it proceeds catastrophically near the jet photosphere at large radii (r {approx} 10{sup 13}-10{sup 14}cm), by which the jet obtains a high Lorentz factor ({gamma} {approx} 100-1000), has a luminosity of L{sub j} {approx} 10{sup 50}-10{sup 51} erg s{sup -1}, has observer variability timescales of order 1s (ranging from 0.001-10s), achieves {gamma}{theta}{sub j} {approx} 10-20 (for opening half-angle {theta}{sub j}) and so is able to produce jet breaks, and has comparable energy available for both prompt and afterglow emission. A range of model parameters are investigated and simplified scaling laws are derived. This reconnection switch mechanism allows for highly efficient conversion of electromagnetic energy into prompt emission and associates the observed prompt GRB pulse temporal structure with dissipation timescales of some number of reconnecting current sheets embedded in the jet. We hope this work helps motivate the

The production of lithium oxide microspheres from the disintegration of a liquid jet

International Nuclear Information System (INIS)

Al-Ubaidi, M.R.; Anno, J.N.

1989-01-01

Microspheres of lithium hydroxide (LiOH) were produced from in-flight solidification of droplets formed by the disintegration of an acoustically driven, mechanically vibrated cylindrical liquid jet of molten LiOH. The molten material at 470 to 480 degrees C was fed through a 25-gauge (0.0267-cm bore diameter) nozzle, interiorly electroplated with silver, under ∼27.6-kPa (4-psig) pressure, and at a mechanical vibration frequency of 10 Hz. The resulting jet issued into a 5.5-cm-diam vertical glass drop tube entraining a 94.5 cm 3 /s (12 ft 3 /h) argon gas stream at 75 degrees C. The 100-cm-long drop tube was sufficient to allow the droplets of molten LiOH resulting from jet disintegration to solidify in-flight without catastrophic thermal shock, being then collected a solid microspheres. These LiOH microspheres were then vacuum processed to lithium oxide (Li 2 O). Preliminary experiments resulted in microspheres with diameters varying from 120 to 185 μm, but with evidence of impurity contamination occurring during the initial stages of the process

The State-of-the-Art for Ventilative Cooling

DEFF Research Database (Denmark)

Heiselberg, Per Kvols

2016-01-01

Ventilative cooling for buildings may lead to cooling energy savings and improvements in thermal comfort, especially in seasonally temperate and warm climates. But, codes and regulations need to better quantify its benefits.......Ventilative cooling for buildings may lead to cooling energy savings and improvements in thermal comfort, especially in seasonally temperate and warm climates. But, codes and regulations need to better quantify its benefits....

Catastrophic primary antiphospholipid syndrome

International Nuclear Information System (INIS)

Kim, Dong Hun; Byun, Joo Nam; Ryu, Sang Wan

2006-01-01

Catastrophic antiphospholipid syndrome (CAPLS) was diagnosed in a 64-year-old male who was admitted to our hospital with dyspnea. The clinical and radiological examinations showed pulmonary thromboembolism, and so thromboembolectomy was performed. Abdominal distension rapidly developed several days later, and the abdominal computed tomography (CT) abdominal scan revealed thrombus within the superior mesenteric artery with small bowel and gall bladder distension. Cholecystectomy and jejunoileostomy were performed, and gall bladder necrosis and small bowel infarction were confirmed. The anticardiolipin antibody was positive. Anticoagulant agents and steroids were administered, but the patient expired 4 weeks after surgery due to acute respiratory distress syndrome (ARDS). We report here on a case of catastrophic APLS with manifestations of pulmonary thromboembolism, rapidly progressing GB necrosis and bowel infarction

Catastrophic primary antiphospholipid syndrome

Energy Technology Data Exchange (ETDEWEB)

Kim, Dong Hun; Byun, Joo Nam [Chosun University Hospital, Gwangju (Korea, Republic of); Ryu, Sang Wan [Miraero21 Medical Center, Gwangju (Korea, Republic of)

2006-09-15

Catastrophic antiphospholipid syndrome (CAPLS) was diagnosed in a 64-year-old male who was admitted to our hospital with dyspnea. The clinical and radiological examinations showed pulmonary thromboembolism, and so thromboembolectomy was performed. Abdominal distension rapidly developed several days later, and the abdominal computed tomography (CT) abdominal scan revealed thrombus within the superior mesenteric artery with small bowel and gall bladder distension. Cholecystectomy and jejunoileostomy were performed, and gall bladder necrosis and small bowel infarction were confirmed. The anticardiolipin antibody was positive. Anticoagulant agents and steroids were administered, but the patient expired 4 weeks after surgery due to acute respiratory distress syndrome (ARDS). We report here on a case of catastrophic APLS with manifestations of pulmonary thromboembolism, rapidly progressing GB necrosis and bowel infarction.

Advanced thermally stable jet fuels

Energy Technology Data Exchange (ETDEWEB)

Schobert, H.H.

1999-01-31

The Pennsylvania State University program in advanced thermally stable coal-based jet fuels has five broad objectives: (1) Development of mechanisms of degradation and solids formation; (2) Quantitative measurement of growth of sub-micrometer and micrometer-sized particles suspended in fuels during thermal stressing; (3) Characterization of carbonaceous deposits by various instrumental and microscopic methods; (4) Elucidation of the role of additives in retarding the formation of carbonaceous solids; (5) Assessment of the potential of production of high yields of cycloalkanes by direct liquefaction of coal. Future high-Mach aircraft will place severe thermal demands on jet fuels, requiring the development of novel, hybrid fuel mixtures capable of withstanding temperatures in the range of 400--500 C. In the new aircraft, jet fuel will serve as both an energy source and a heat sink for cooling the airframe, engine, and system components. The ultimate development of such advanced fuels requires a thorough understanding of the thermal decomposition behavior of jet fuels under supercritical conditions. Considering that jet fuels consist of hundreds of compounds, this task must begin with a study of the thermal degradation behavior of select model compounds under supercritical conditions. The research performed by The Pennsylvania State University was focused on five major tasks that reflect the objectives stated above: Task 1: Investigation of the Quantitative Degradation of Fuels; Task 2: Investigation of Incipient Deposition; Task 3: Characterization of Solid Gums, Sediments, and Carbonaceous Deposits; Task 4: Coal-Based Fuel Stabilization Studies; and Task 5: Exploratory Studies on the Direct Conversion of Coal to High Quality Jet Fuels. The major findings of each of these tasks are presented in this executive summary. A description of the sub-tasks performed under each of these tasks and the findings of those studies are provided in the remainder of this volume

Vortex Structure Effects on Impingement, Effusion, and Cross Flow Cooling of a Double Wall Configuration

Science.gov (United States)

Ligrani, P. M.

2018-03-01

A variety of different types of vortices and vortex structures have important influences on thermal protection, heat transfer augmentation, and cooling performance of impingement cooling, effusion cooling, and cross flow cooling. Of particular interest are horseshoe vortices, which form around the upstream portions of effusion coolant concentrations just after they exit individual holes, hairpin vortices, which develop nearby and adjacent to effusion coolant trajectories, and Kelvin-Helmholtz vortices which form within the shear layers that form around each impingement cooling jet. The influences of these different vortex structures are described as they affect and alter the thermal performance of effusion cooling, impingement cooling, and cross flow cooling, as applied to a double wall configuration.

Vaginismus: heightened harm avoidance and pain catastrophizing cognitions.

Science.gov (United States)

Borg, Charmaine; Peters, Madelon L; Schultz, Willibrord Weijmar; de Jong, Peter J

2012-02-01

Catastrophic appraisal of experienced pain may promote hypervigilance and intense pain, while the personality trait of harm avoidance (HA) might prevent the occurrence of correcting such experiences. Women inflicted with vaginismus may enter a self-perpetuating downward spiral of increasing avoidance of (anticipated) pain. In vaginismus the anticipation of pain may give rise to catastrophic pain ideation. This may establish hypervigilance toward painful sexual stimuli, which consequently results in negative appraisal of sexual cues. This process could impair genital and sexual responding, intensify pain and trigger avoidance, which in turn may contribute to the onset and persistence of symptoms in vaginismus and to certain extent also in dyspareunia. To investigate whether women suffering from vaginismus are characterized by heightened levels of habitual pain catastrophic cognitions, together with higher levels of HA. This study consisted of three groups: a lifelong vaginismus group (N = 35, mean age = 28.4; standard deviation [SD] = 5.8), a dyspareunia group (N = 33, mean age = 26.7; SD = 6.8), and women without sexual complaints (N = 54, mean age = 26.5; SD = 6.7). HA scale of Cloninger's tridimensional personality questionnaire, and the pain catastrophizing scale. Specifically women inflicted with vaginismus showed significantly heightened levels of catastrophic pain cognitions compared with the other two groups, as well as significant enhanced HA vs. the control group, and a trend vs. the dyspareunia group. Both traits were shown to have cumulative predictive validity for the presence of vaginismus. This study focused on the personality traits of catastrophizing pain cognitions and HA in women with lifelong vaginismus. Our findings showed that indeed, women suffering from vaginismus are characterized by trait of HA interwoven with habitual pain catastrophizing cognitions. This study could help in the refinement of the current conceptualization and might shed

Very forward jet, Mueller Navelet jets and jet gap jet measurements in CMS

CERN Document Server

Cerci, Salim

2018-01-01

The measurements of very forward jet, Mueller-Navelet jets and jet-gap-jet events are presented for different collision energies. The analyses are based on data collected with the CMS detector at the LHC. Jets are defined through the anti-$k_\\mathrm{t}$ clustering algorithm for different cone sizes. Jet production studies provide stringent tests of quantum chromodynamics (QCD) and contribute to tune Monte Carlo (MC) simulations and phenomenological models. The measurements are compared to predictions from various Monte Carlo event generators.

Socioeconomic inequality in catastrophic health expenditure in Brazil.

Science.gov (United States)

Boing, Alexandra Crispim; Bertoldi, Andréa Dâmaso; Barros, Aluísio Jardim Dornellas de; Posenato, Leila Garcia; Peres, Karen Glazer

2014-08-01

To analyze the evolution of catastrophic health expenditure and the inequalities in such expenses, according to the socioeconomic characteristics of Brazilian families. Data from the National Household Budget 2002-2003 (48,470 households) and 2008-2009 (55,970 households) were analyzed. Catastrophic health expenditure was defined as excess expenditure, considering different methods of calculation: 10.0% and 20.0% of total consumption and 40.0% of the family's capacity to pay. The National Economic Indicator and schooling were considered as socioeconomic characteristics. Inequality measures utilized were the relative difference between rates, the rates ratio, and concentration index. The catastrophic health expenditure varied between 0.7% and 21.0%, depending on the calculation method. The lowest prevalences were noted in relation to the capacity to pay, while the highest, in relation to total consumption. The prevalence of catastrophic health expenditure increased by 25.0% from 2002-2003 to 2008-2009 when the cutoff point of 20.0% relating to the total consumption was considered and by 100% when 40.0% or more of the capacity to pay was applied as the cut-off point. Socioeconomic inequalities in the catastrophic health expenditure in Brazil between 2002-2003 and 2008-2009 increased significantly, becoming 5.20 times higher among the poorest and 4.17 times higher among the least educated. There was an increase in catastrophic health expenditure among Brazilian families, principally among the poorest and those headed by the least-educated individuals, contributing to an increase in social inequality.

Understanding catastrophizing from a misdirected problem-solving perspective.

Science.gov (United States)

Flink, Ida K; Boersma, Katja; MacDonald, Shane; Linton, Steven J

2012-05-01

The aim is to explore pain catastrophizing from a problem-solving perspective. The links between catastrophizing, problem framing, and problem-solving behaviour are examined through two possible models of mediation as inferred by two contemporary and complementary theoretical models, the misdirected problem solving model (Eccleston & Crombez, 2007) and the fear-anxiety-avoidance model (Asmundson, Norton, & Vlaeyen, 2004). In this prospective study, a general population sample (n= 173) with perceived problems with spinal pain filled out questionnaires twice; catastrophizing and problem framing were assessed on the first occasion and health care seeking (as a proxy for medically oriented problem solving) was assessed 7 months later. Two different approaches were used to explore whether the data supported any of the proposed models of mediation. First, multiple regressions were used according to traditional recommendations for mediation analyses. Second, a bootstrapping method (n= 1000 bootstrap resamples) was used to explore the significance of the indirect effects in both possible models of mediation. The results verified the concepts included in the misdirected problem solving model. However, the direction of the relations was more in line with the fear-anxiety-avoidance model. More specifically, the mediation analyses provided support for viewing catastrophizing as a mediator of the relation between biomedical problem framing and medically oriented problem-solving behaviour. These findings provide support for viewing catastrophizing from a problem-solving perspective and imply a need to examine and address problem framing and catastrophizing in back pain patients. ©2011 The British Psychological Society.

Nuclear war and other catastrophes. Civil and catastrophe protection in the Federal republic of Germany and the United Kingdom after 1945

International Nuclear Information System (INIS)

Diebel, Martin

2017-01-01

The book civil and catastrophe protection in the Federal republic of Germany and the United Kingdom after 1945 discusses the following issues: aerial defense and the atomic bomb (1945 - 1968), crises and catastrophes in the shadow of the bomb (1962 - 1978), civil defense and the comeback of the (nuclear) war (1976 - 1979), civil defense and the second ''Cold War'' (1979 - 1986), Chernobyl and the end of the Cold War (1979 - 1990), war, catastrophe and safety in the 20th century - a conclusion.

Turbulent heat mixing of a heavy liquid metal flow in the MEGAPIE target geometry-The heated jet experiment

International Nuclear Information System (INIS)

Stieglitz, Robert; Daubner, Markus; Batta, A.; Lefhalm, C.-H.

2007-01-01

The MEGAPIE target installed at the Paul-Scherrer Institute is an example of a spallation target using eutectic liquid lead-bismuth (Pb 45 Bi 55 ) both as coolant and neutron source. An adequate cooling of the target requires a conditioning of the flow, which is realized by a main flow transported in an annular gap downwards, u-turned at a hemispherical shell into a cylindrical riser tube. In order to avoid a stagnation point close to the lowest part of the shell a jet flow is superimposed to the main flow, which is directed towards to the stagnation point and flows tangentially along the shell. The heated jet experiment conducted in the THEADES loop of the KALLA laboratory is nearly 1:1 representation of the lower part of the MEGAPIE target. It is aimed to study the cooling capability of this specific geometry in dependence on the flow rate ratio (Q main /Q jet ) of the main flow (Q main ) to the jet flow (Q jet ). Here, a heated jet is injected into a cold main flow at MEGAPIE relevant flow rate ratios. The liquid metal experiment is accompanied by a water experiment in almost the same geometry to study the momentum field as well as a three-dimensional turbulent numerical fluid dynamic simulation (CFD). Besides a detailed study of the envisaged nominal operation of the MEGAPIE target with Q main /Q jet = 15 deviations from this mode are investigated in the range from 7.5 ≤ Q main /Q jet ≤ 20 in order to give an estimate on the safe operational threshold of the target. The experiment shows that, the flow pattern establishing in this specific design and the turbulence intensity distribution essentially depends on the flow rate ratio (Q main /Q jet ). All Q main /Q jet -ratios investigated exhibit an unstable time dependent behavior. The MEGAPIE design is highly sensitive against changes of this ratio. Mainly three completely different flow patterns were identified. A sufficient cooling of the lower target shell, however, is only ensured if Q main /Q jet ≤ 12

Water mist effect on cooling range and efficiency of casting die

Directory of Open Access Journals (Sweden)

R. Władysiak

2008-12-01

Full Text Available This project is showing investigation results of cooling process of casting die in the temperature range 570÷100 °C with 0.40 MPa compressed air and water mist streamed under pressure 0.25÷0.45 MPa in air jet 0.25÷0.50 MPa using open cooling system.The character and the speed of changes of temperature, forming of the temperture’s gradient along parallel layer to cooled surface of die is shawing with thermal and derivative curves. The effect of kind of cooling factor on the temperature and time and distance from cooling nozzle is presented in the paper. A designed device for generating the water mist cooling the die and the view of sprying water stream is shown here. It’s proved that using of the water mist together with the change of heat transfer interface increases intensity of cooling in the zone and makes less the range cooling zone and reduces the porosity of cast microstructure.

An alternative cooling system to enhance the safety of Li-ion battery packs

Science.gov (United States)

Kizilel, Riza; Sabbah, Rami; Selman, J. Robert; Al-Hallaj, Said

A passive thermal management system is evaluated for high-power Li-ion packs under stressful or abusive conditions, and compared with a purely air-cooling mode under normal and abuse conditions. A compact and properly designed passive thermal management system utilizing phase change material (PCM) provides faster heat dissipation than active cooling during high pulse power discharges while preserving sufficiently uniform cell temperature to ensure the desirable cycle life for the pack. This study investigates how passive cooling with PCM contributes to preventing the propagation of thermal runaway in a single cell or adjacent cells due to a cell catastrophic failure. Its effectiveness is compared with that of active cooling by forced air flow or natural convection using the same compact module and pack configuration corresponding to the PCM matrix technology. The effects of nickel tabs and spacing between the cells were also studied.

An alternative cooling system to enhance the safety of Li-ion battery packs

Energy Technology Data Exchange (ETDEWEB)

Kizilel, Riza; Sabbah, Rami [Department of Chemical and Biological Engineering, Illinois Institute of Technology, 10 W. 33rd Street, Chicago, IL 60616 (United States); Selman, J. Robert [Department of Chemical and Biological Engineering, Illinois Institute of Technology, 10 W. 33rd Street, Chicago, IL 60616 (United States); All Cell Technologies, LLC, IIT University Technology Park, 3440 S. Dearborn Street, Suite 117N, Chicago, IL 60616 (United States); Al-Hallaj, Said [All Cell Technologies, LLC, IIT University Technology Park, 3440 S. Dearborn Street, Suite 117N, Chicago, IL 60616 (United States)

2009-12-01

A passive thermal management system is evaluated for high-power Li-ion packs under stressful or abusive conditions, and compared with a purely air-cooling mode under normal and abuse conditions. A compact and properly designed passive thermal management system utilizing phase change material (PCM) provides faster heat dissipation than active cooling during high pulse power discharges while preserving sufficiently uniform cell temperature to ensure the desirable cycle life for the pack. This study investigates how passive cooling with PCM contributes to preventing the propagation of thermal runaway in a single cell or adjacent cells due to a cell catastrophic failure. Its effectiveness is compared with that of active cooling by forced air flow or natural convection using the same compact module and pack configuration corresponding to the PCM matrix technology. The effects of nickel tabs and spacing between the cells were also studied. (author)

IMPINGEMENT COOLING OF A SEMI-CIRCULAR CONCAVE CHANNEL BY 2D AIR-JET

Directory of Open Access Journals (Sweden)

Serhan KÜÇÜKA

1998-01-01

Full Text Available This study provides a numerical solution to the flow in a cylindrical cavity of which the upper wall contains a twodimensional slot. The air injected through the slot impinges and diffuses laterally on the lower wall. The jet enfluxed through the slot is assumed to have uniform velocity and temperature, and the temperature at the lower wall is kept constant. The resulting Navier-Stokes equations are solved by transforming simpler algorithm into a form useably in cylindrical co-ordinate system. The effect of cavity curvature, and the height ratio on velocity and pressure distribution is analyzed. The jet Reynolds number ranged from 100 to 1500 in the analysis.

Impact of the initial streamwise inclination of a double jet emitted within a cool crossflow on its temperature field and pollutants dispersion

Energy Technology Data Exchange (ETDEWEB)

Radhouane, A.; Mahjoub Said, Nejla; Mhiri, H. [Ecole Nationale d' Ingenieurs de Monastir, Unite de Thermique et Thermodynamique des Procedes Industriels, Monastir (Tunisia); Palec, G. le; Bournot, P. [IUSTI, UMR 6595, Technopole de Chateau-Gombert, Marseille (France)

2009-04-15

An experimental study and a numerical modeling are carried out simultaneously on a twin inclined jets' configuration issuing into a cooler crossflow. The main purpose of this study is to track the overall evolution of the jets among the surrounding flow and then determine the thermal and mass transfer features that characterize the resulting flowfield. The experimental data are depicted by means of a particle image velocimetry technique; whereas the numerical three-dimensional model is simulated through the resolution of the different governing Navier-Stokes' equations by means of the finite volume method. Two different closure models were tested: the standard k-{epsilon} model and the Reynolds stress model (RSM) second order model. The introduction of the latter in such a configuration brings some valuable improvement since it allows the detection of the slightest variations within the domain and then describes the least occurring mechanisms. The confrontation of the differently processed numerical results with the experimentally tracked data comforted our opinion since it proved the better efficiency of the RSM model for the description of the handled flow; that's why we adopted it for the rest of the paper. Once the validation obtained, we proceeded to the evaluation of the influence of the initial streamwise inclination of the emitted jets on the engendered thermal field and on the pollutants' dispersion. For the matter, we tested the following angles: 30 , 45 , 60 and 90 . After that, we represented the temperature variation along different directions in order to detail its behavior in all of them and at different levels. This characterization is highly recommended since it may promote the efficiency of several applications (mainly the cooling applications). We also evaluated the influence of this same parameter; the initial inclination; on the pollutants' dispersion due to the high and alarming importance of the problem on the

Rotation Effect on Jet Impingement Heat Transfer in Smooth Rectangular Channels with Film Coolant Extraction

Directory of Open Access Journals (Sweden)

James A. Parsons

2001-01-01

Full Text Available The effect of channel rotation on jet impingement cooling by arrays of circular jets in twin channels was studied. Impinging jet flows were in the direction of rotation in one channel and opposite to the direction of rotation in the other channel. The jets impinged normally on the smooth, heated target wall in each channel. The spent air exited the channels through extraction holes in each target wall, which eliminates cross flow on other jets. Jet rotation numbers and jet Reynolds numbers varied from 0.0 to 0.0028 and 5000 to 10,000, respectively. For the target walls with jet flow in the direction of rotation (or opposite to the direction of rotation, as rotation number increases heat transfer decreases up to 25% (or 15% as compared to corresponding results for non-rotating conditions. This is due to the changes in flow distribution and rotation induced Coriolis and centrifugal forces.

Clinical Pain Catastrophizing in Women With Migraine and Obesity.

Science.gov (United States)

Bond, Dale S; Buse, Dawn C; Lipton, Richard B; Thomas, J Graham; Rathier, Lucille; Roth, Julie; Pavlovic, Jelena M; Evans, E Whitney; Wing, Rena R

2015-01-01

Obesity is related to migraine. Maladaptive pain coping strategies (eg, pain catastrophizing) may provide insight into this relationship. In women with migraine and obesity, we cross-sectionally assessed: (1) prevalence of clinical catastrophizing; (2) characteristics of those with and without clinical catastrophizing; and (3) associations of catastrophizing with headache features. Obese women migraineurs seeking weight loss treatment (n = 105) recorded daily migraine activity for 1 month via smartphone and completed the Pain Catastrophizing Scale (PCS). Clinical catastrophizing was defined as total PCS score ≥30. The six-item Headache Impact Test (HIT-6), 12-item Allodynia Symptom Checklist (ASC-12), Headache Management Self-Efficacy Scale (HMSE), and assessments for depression (Centers for Epidemiologic Studies Depression Scale) and anxiety (seven-item Generalized Anxiety Disorder Scale) were also administered. Using PCS scores and body mass index (BMI) as predictors in linear regression, we modeled a series of headache features (ie, headache days, HIT-6, etc) as outcomes. One quarter (25.7%; 95% confidence interval [CI] = 17.2-34.1%) of participants met criteria for clinical catastrophizing: they had higher BMI (37.9 ± 7.5 vs 34.4 ± 5.7 kg/m(2) , P = .035); longer migraine attack duration (160.8 ± 145.0 vs 97.5 ± 75.2 hours/month, P = .038); higher HIT-6 scores (68.7 ± 4.6 vs 64.5 ± 3.9, P duration (β = 0.390, P duration, higher pain sensitivity, greater headache impact, and lower headache management self-efficacy. In all participants, PCS scores were related to several migraine characteristics, above and beyond the effects of obesity. Prospective studies are needed to determine sequence and mechanisms of relationships between catastrophizing, obesity, and migraine. © 2015 American Headache Society.

Catastrophic events and older adults.

Science.gov (United States)

Cloyd, Elizabeth; Dyer, Carmel B

2010-12-01

The plight of older adults during catastrophic events is a societal concern. Older persons have an increased prevalence of cognitive disorders, chronic illnesses, and mobility problems that limit their ability to cope. These disorders may result in a lack of mental capacity and the ability to discern when they should evacuate or resolve problems encountered during a catastrophe. Some older persons may have limited transportation options, and many of the elderly survivors are at increased risk for abuse, neglect, and exploitation. Recommendations for future catastrophic events include the development of a federal tracking system for elders and other vulnerable adults, the designation of separate shelter areas for elders and other vulnerable adults, and involvement of gerontological professionals in all aspects of emergency preparedness and care delivery, including training of frontline workers. Preparation through preevent planning that includes region-specific social services, medical and public health resources, volunteers, and facilities for elders and vulnerable adults is critical. Elders need to be protected from abuse and fraud during catastrophic events. A public health triage system for elders and other vulnerable populations in pre- and postdisaster situations is useful, and disaster preparedness is paramount. Communities and members of safety and rescue teams must address ethical issues before an event. When older adults are involved, consideration needs to be given to triage decision making, transporting those who are immobile, the care of older adults who receive palliative care, and the equitable distribution of resources. Nurses are perfectly equipped with the skills, knowledge, and training needed to plan and implement disaster preparedness programs. In keeping with the tradition of Florence Nightingale, nurses can assume several crucial roles in disaster preparedness for older adults. Nurses possess the ability to participate and lead community

Empirical Bayes Credibility Models for Economic Catastrophic Losses by Regions

Directory of Open Access Journals (Sweden)

Jindrová Pavla

2017-01-01

Full Text Available Catastrophic events affect various regions of the world with increasing frequency and intensity. The number of catastrophic events and the amount of economic losses is varying in different world regions. Part of these losses is covered by insurance. Catastrophe events in last years are associated with increases in premiums for some lines of business. The article focus on estimating the amount of net premiums that would be needed to cover the total or insured catastrophic losses in different world regions using Bühlmann and Bühlmann-Straub empirical credibility models based on data from Sigma Swiss Re 2010-2016. The empirical credibility models have been developed to estimate insurance premiums for short term insurance contracts using two ingredients: past data from the risk itself and collateral data from other sources considered to be relevant. In this article we deal with application of these models based on the real data about number of catastrophic events and about the total economic and insured catastrophe losses in seven regions of the world in time period 2009-2015. Estimated credible premiums by world regions provide information how much money in the monitored regions will be need to cover total and insured catastrophic losses in next year.

Catastrophe Theory and Caustics

DEFF Research Database (Denmark)

Gravesen, Jens

1983-01-01

It is shown by elementary methods that in codimension two and under the assumption that light rays are straight lines, a caustic is the catastrophe set for a time function. The general case is also discussed....

The catastrophic antiphospholipid syndrome in children.

Science.gov (United States)

Go, Ellen J L; O'Neil, Kathleen M

2017-09-01

To review the difficult syndrome of catastrophic antiphospholipid syndrome, emphasizing new developments in the diagnosis, pathogenesis and treatment. Few recent publications directly address pediatric catastrophic antiphospholipid syndrome (CAPS). Most articles are case reports or are data from adult and pediatric registries. The major factors contributing to most pediatric catastrophic antiphospholipid syndrome include infection and the presence of antiphospholipid antibodies, but complement activation also is important in creating diffuse thrombosis in the microcirculation. Treatment of the acute emergency requires anticoagulation, suppression of the hyperinflammatory state and elimination of the triggering infection. Inhibition of complement activation appears to improve outcome in limited studies, and suppression of antiphospholipid antibody formation may be important in long-term management. CAPS, an antibody-mediated diffuse thrombotic disease of microvasculature, is rare in childhood but has high mortality (33-50%). It requires prompt recognition and aggressive multimodality treatment, including anticoagulation, anti-inflammatory therapy and elimination of inciting infection and pathogenic autoantibodies.

Orthogonality catastrophe and fractional exclusion statistics

Science.gov (United States)

Ares, Filiberto; Gupta, Kumar S.; de Queiroz, Amilcar R.

2018-02-01

We show that the N -particle Sutherland model with inverse-square and harmonic interactions exhibits orthogonality catastrophe. For a fixed value of the harmonic coupling, the overlap of the N -body ground state wave functions with two different values of the inverse-square interaction term goes to zero in the thermodynamic limit. When the two values of the inverse-square coupling differ by an infinitesimal amount, the wave function overlap shows an exponential suppression. This is qualitatively different from the usual power law suppression observed in the Anderson's orthogonality catastrophe. We also obtain an analytic expression for the wave function overlaps for an arbitrary set of couplings, whose properties are analyzed numerically. The quasiparticles constituting the ground state wave functions of the Sutherland model are known to obey fractional exclusion statistics. Our analysis indicates that the orthogonality catastrophe may be valid in systems with more general kinds of statistics than just the fermionic type.

Manufacture and installation of JET MKII divertor support structure

International Nuclear Information System (INIS)

Celentano, G.; Altmann, H.; Macklin, B.; Miele, P.; Pick, M.A.; Tait, J.; Moletta, L.; Romagnolo, A.; Shaw, R.

1995-01-01

The water cooled support structure, comprising twenty-four modules is the main component of the JET MKII divertor system. It is to be installed in the vacuum vessel with high accuracy with respect to the magnetic center and the other in-vessel components. The paper describes the design and manufacturing cycle including the required tolerances, the assembly and installation method and the material production process required to ensure the accuracy and reliability of the MKII support structure system. The water cooling holes, machined into the support structure require the procurement of special material to prevent risks of leaks inside the vacuum vessel

Experimental investigation of impingement cooling with turbulators or surface enlarging elements

Energy Technology Data Exchange (ETDEWEB)

Persson, Johan

2000-02-01

For the materials in modern gas turbines to sustain, a considerable amount of cooling is required. In cases where large amounts of heat need to be removed, impingement cooling with its high heat transfer coefficients may be the only alternative. In this work the possibilities of enhancing impingement cooling by introducing surface enlarging - turbulence enhancing elements are examined experimentally. A configuration consisting of a staggered array of 45 impingement jets distributed over 10 rows is used for the purpose. A thermo camera is used to measure the temperature distribution on the target plate, giving an opportunity to separately evaluate the Nusselt number enhancement for different areas. Experiments are conducted for five different area enlarging geometries: triangle, wing, cylinder, dashed rib, and angel, all made from aluminium. Comparison between each area enlarged surface and a flat plate is made, with results presented as Nusselt number enhancement factors. The effect of pumping power required is also investigated in order to maximize the cooling efficiency. Parameters varied are Reynolds number and jet to plate distance. Overall Nusselt number enhancement factors show values of 1 to 1.3, the trend being decreasing with increased jet to plane distance and Reynolds number. When taking into account pumping power the enhancement factors drop to 0.4 to 1.2. The best results are achieved with the rib geometry and when not using a too large value of enlarger height over jet to plate distance (h/z). Row wise evaluation of Nusselt number enhancement shows an increased enhancement with row number and thereby crossflow ratio (Gc/Gj). Typical increases in enhancement of 1 to 1.5 with Gc/Gj from 0 to 0.8 are found. The thermo camera pictures reveal that the enhancement is found in three different areas, on the enlarger base area, the area just downstream the enlarger and in diagonal streaks with increased turbulence caused by the enlargers. Tests using an

Paraboles et catastrophes

CERN Document Server

Thom, René

1983-01-01

René Thom, mathématicien français, membre de l'Académie des Sciences, s'est vu décerner en 1958 la médaille Field, équivalent du Prix Nobel en mathématiques, pour ses créations intellectuelles, la " théorie des catastrophes ", regard nouveau sur toutes les transformations qui adviennent de manière brusque, imprévisible, dramatique. Dans ces entretiens qui vont de la mathématique à l'embryologie, de la linguistique à l'anthropologie et à l'histoire, René Thom expose les grandes lignes de la théorie des catastrophes et passe en revue, avec un esprit à la fois critique et passionné, les grands thèmes scientifiques de notre époque, de la physique atomique à la biologie moléculaire, du " progrès " scientifique et technologique aux connexions complexes entre la société et la science. " Ce petit livre est une extraordinaire réussite en vulgarisation ". (Jean Largeault)

Catastrophe, Gender and Urban Experience, 1648–1920

DEFF Research Database (Denmark)

Employing a broad definition of catastrophe, this book examines how urban communities conceived, adapted to and were transformed by catastrophes. Competing views of gender figure in the telling and retelling of these trag- edies, which are mediated by myth and memory. This is a nuanced account...

Characteristics of polar coronal hole jets

Science.gov (United States)

Chandrashekhar, K.; Bemporad, A.; Banerjee, D.; Gupta, G. R.; Teriaca, L.

2014-01-01

point suggest that the sigmoid is the progenitor of the jet. Conclusions: The enhancement in the light curves of low-temperature EIS lines in the later phase of the jet lifetime and the shape of the jet's stack plots suggests that the jet material falls back, and most likely cools down. To further support this conclusion, the observed drifts were interpreted within a scenario where reconnection progressively shifts along a magnetic structure, leading to the sequential appearance of jets of about the same size and physical characteristics. On this basis, we also propose a simple qualitative model that mimics the observations. Movies 1-3 are available in electronic form at http://www.aanda.org Warning, no authors found for 2014A&A...561A..97.

Simulation and performance enhancement of the air cooling system in a DC/AC power converter station

Energy Technology Data Exchange (ETDEWEB)

Lozowy, R.; El-Shaboury, A.; Soliman, H.; Ormiston, S. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Mechanical and Manufacturing Engineering

2010-07-01

This study analyzed the flow structure and heat transfer in a large 3-dimensional domain with turbulence, mixed convection, an impinging jet, and flow over heated blocks. The objective was to better understand turbulent mixed-convection cooling of heat-generating bodies in 3-dimensional enclosures, which is important to industry. The cooling of 2 thyristor valve halls was simulated. Each valve hall housed 3 towers that contained electronics used in DC/AC power conversion. The simulation results included the magnitudes of the net air flows for all the inter-block gaps and the maximum temperature in each gap. A parametric study was also performed to investigate the effects of the air inlet location, size and aspect ratio. The effects of the air injection angle on cooling effectiveness was also examined. The study showed that for fixed inlet mass flow rate, significant improvement in the cooling effectiveness can be obtained by changing the injection angle of the inlet air jet, the location of the inlet grill, or the size of the inlet grill. It was concluded that these study results may be relevant to other applications, such as the design of power transformers, the design of cooling systems for spent nuclear fuel and computer server cooling racks. 13 refs., 12 figs.

A small-scale eruption leading to a blowout macrospicule jet in an on-disk coronal hole

International Nuclear Information System (INIS)

Adams, Mitzi; Sterling, Alphonse C.; Moore, Ronald L.; Gary, G. Allen

2014-01-01

We examine the three-dimensional magnetic structure and dynamics of a solar EUV-macrospicule jet that occurred on 2011 February 27 in an on-disk coronal hole. The observations are from the Solar Dynamics Observatory (SDO) Atmospheric Imaging Assembly (AIA) and the SDO Helioseismic and Magnetic Imager (HMI). The observations reveal that in this event, closed-field-carrying cool absorbing plasma, as in an erupting mini-filament, erupted and opened, forming a blowout jet. Contrary to some jet models, there was no substantial recently emerged, closed, bipolar-magnetic field in the base of the jet. Instead, over several hours, flux convergence and cancellation at the polarity inversion line inside an evolved arcade in the base apparently destabilized the entire arcade, including its cool-plasma-carrying core field, to undergo a blowout eruption in the manner of many standard-sized, arcade-blowout eruptions that produce a flare and coronal mass ejection. Internal reconnection made bright 'flare' loops over the polarity inversion line inside the blowing-out arcade field, and external reconnection of the blowing-out arcade field with an ambient open field made longer and dimmer EUV loops on the outside of the blowing-out arcade. That the loops made by the external reconnection were much larger than the loops made by the internal reconnection makes this event a new variety of blowout jet, a variety not recognized in previous observations and models of blowout jets.

A small-scale eruption leading to a blowout macrospicule jet in an on-disk coronal hole

Energy Technology Data Exchange (ETDEWEB)

Adams, Mitzi; Sterling, Alphonse C.; Moore, Ronald L. [Space Science Office, ZP13, NASA Marshall Space Flight Center, Huntsville, AL 35812 (United States); Gary, G. Allen, E-mail: mitzi.adams@nasa.gov, E-mail: alphonse.sterling@nasa.gov, E-mail: ron.moore@nasa.gov, E-mail: gag0002@uah.edu [Center for Space Plasma and Aeronomic Research, The University of Alabama in Huntsville, Huntsville, AL 35805, USA. (United States)

2014-03-01

We examine the three-dimensional magnetic structure and dynamics of a solar EUV-macrospicule jet that occurred on 2011 February 27 in an on-disk coronal hole. The observations are from the Solar Dynamics Observatory (SDO) Atmospheric Imaging Assembly (AIA) and the SDO Helioseismic and Magnetic Imager (HMI). The observations reveal that in this event, closed-field-carrying cool absorbing plasma, as in an erupting mini-filament, erupted and opened, forming a blowout jet. Contrary to some jet models, there was no substantial recently emerged, closed, bipolar-magnetic field in the base of the jet. Instead, over several hours, flux convergence and cancellation at the polarity inversion line inside an evolved arcade in the base apparently destabilized the entire arcade, including its cool-plasma-carrying core field, to undergo a blowout eruption in the manner of many standard-sized, arcade-blowout eruptions that produce a flare and coronal mass ejection. Internal reconnection made bright 'flare' loops over the polarity inversion line inside the blowing-out arcade field, and external reconnection of the blowing-out arcade field with an ambient open field made longer and dimmer EUV loops on the outside of the blowing-out arcade. That the loops made by the external reconnection were much larger than the loops made by the internal reconnection makes this event a new variety of blowout jet, a variety not recognized in previous observations and models of blowout jets.

Obstetric Antecedents to Body Cooling Treatment of the Newborn Infant

Science.gov (United States)

Nelson, David B.; Lucke, Ashley M.; McIntire, Donald D.; Sánchez, Pablo J.; Leveno, Kenneth J.; Chalak, Lina F.

2014-01-01

Objective Obstetric antecedents were analyzed in births where the infant received whole-body cooling for neonatal encephalopathy. Methods This retrospective cohort study included all live-born singleton infants delivered at or beyond 36 weeks gestation from October 2005 through December 2011. Infants who had received whole-body cooling identified by review of a prospective neonatal registry were compared to a control group comprising the remaining obstetric population delivered at greater than 36 weeks but not cooled. Univariable analysis was followed by a staged, stepwise selection of variables with the intent to rank significant risk factors for cooling. Results A total of 86,371 women delivered during the study period and 98 infants received whole-body cooling (1.1/1,000 livebirths). Of these 98 infants, 80 (88%) newborns had moderate encephalopathy and 10 (12%) had severe encephalopathy prior to cooling. Maternal age less than or equal to 15 years, low parity, maternal body habitus (BMI ≥ 40 kg/m2), diabetes, preeclampsia, induction, epidural analgesia, chorioamnionitis, length of labor, and mode of delivery were associated with significantly increased risk of infant cooling during univariable analysis. Catastrophic events to include umbilical cord prolapse (OR 14; 95%CI, 3–72), placental abruption (OR 17; 95%CI, 7–44), uterine rupture (OR 130; 95%CI, 11–1477) were the strongest factors associated with infant cooling after staged-stepwise logistic analysis. Conclusion A variety of intrapartum characteristics were associated with infant cooling for neonatal encephalopathy with the most powerful antecedents being umbilical cord prolapse, placental abruption, and uterine rupture. PMID:24530976

Dual fluorescence excitation spectra of methyl salicylate in a free jet

Science.gov (United States)

Heimbrook, Lou Ann; Kenny, Jonathan E.; Kohler, Bryan E.; Scott, Gary W.

1981-11-01

Separate fluorescence excitation spectra of the blue- and UV-emitting forms of methyl salicylate cooled in a free-jet expansion are reported. This study represents the first observation of the detailed vibrational structure of these transitions. The two excitation spectra have no features in common, and their intensity patterns are very different. Many individual lines are ˜2 cm-1 wide (nearly laser limited), although in the excitation spectrum of the UV emission, spectral congestion persists at high energies despite the high degree of cooling. (AIP)

Ancient Jets of Fiery Rain

Science.gov (United States)

Taylor, G. J.

2015-04-01

Chondrules are intriguing millimeter-sized crystallized droplets that are abundant in chondrites, so named because of the presence of numerous chondrules. They have puzzled cosmochemists since they were described by English scientist H. C. Sorby in 1877. Everyone agrees that they formed as molten droplets of silicates, but nobody agrees on how the little things formed. Ideas range from impacts onto asteroids, primary condensation in the solar nebula, shock waves and/or lightening in the solar nebula, or by processes operating as planets began to form. A new twist on this last idea was investigated in a new way by Brandon Johnson (Massachusetts Institute of Technology, MIT) and co-authors David Minton and Jay Melosh (Purdue University), and Maria Zuber at MIT. Johnson and coworkers modeled the effects of impacts between planetesimals 100-1000 kilometers in diameter. When such objects hit each other, the first thing that happens is jetting of molten rock. Johnson and colleagues propose that the jets will subdivide into droplets as the jetted material is shot into space. They estimate that the chondrules would have the correct cooling rates (as determined from previous studies of chondrules) and the collision frequency would be high enough to produce abundant chondrules. Johnson and coworkers suggest that chondrules are a "byproduct of [planetary] accretion."

Investigation of Cooling Water Injection into Supersonic Rocket Engine Exhaust

Science.gov (United States)

Jones, Hansen; Jeansonne, Christopher; Menon, Shyam

2017-11-01

Water spray cooling of the exhaust plume from a rocket undergoing static testing is critical in preventing thermal wear of the test stand structure, and suppressing the acoustic noise signature. A scaled test facility has been developed that utilizes non-intrusive diagnostic techniques including Focusing Color Schlieren (FCS) and Phase Doppler Particle Anemometry (PDPA) to examine the interaction of a pressure-fed water jet with a supersonic flow of compressed air. FCS is used to visually assess the interaction of the water jet with the strong density gradients in the supersonic air flow. PDPA is used in conjunction to gain statistical information regarding water droplet size and velocity as the jet is broken up. Measurement results, along with numerical simulations and jet penetration models are used to explain the observed phenomena. Following the cold flow testing campaign a scaled hybrid rocket engine will be constructed to continue tests in a combusting flow environment similar to that generated by the rocket engines tested at NASA facilities. LaSPACE.

Thermo economical optimization of a jet nozzle cooling cycle assisted by solar energy; Otimizacao termoeconomica de ciclo de refrigeracao por compressao por ejetor auxiliado com energia solar

Energy Technology Data Exchange (ETDEWEB)

Tapia, Gabriel I. Medina; Colle, Sergio [Santa Catarina Univ., Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica]. E-mail: gabriel@emc.ufsc.br; colle@emc.ufsc.br

2000-07-01

The present work deals with the analysis of the jet nozzle cooling cycle assisted by solar energy. Both, a thermodynamic and economic optimization are carried out, for ammonia as working fluid. The optimization of the ejector is also focussed, for different values of the relevant design parameters. The method P{sub 1} - {sub P}2 for economical optimization of solar energy systems is used in order to find out the optimum collector area, which corresponds to the maximum value of the life time cost saving. The numerical results are presented in terms of the specific costs of the auxiliary energy, as well as the collector area. (author)

Possibilities of Application of High Pressure Jet Assisted Machining in Hard Turning with Carbide Tools

Directory of Open Access Journals (Sweden)

G. Globočki Lakić

2017-06-01

Full Text Available High Pressure Jet Assisted Machining (HPJAM in turning is a hybrid machining method in which a high pressure jet of cooling and lubrication fluid, under high pressure (50 MPa, leads to the zone between the cutting tool edge and workpiece. An experimental study was performed to investigate the capabilities of conventional and high pressure cooling (HPC in the turning of hard-to-machine materials: hard-chromed and surface hardened steel Ck45 (58 HRc and hardened bearing steel 100Cr6 (62 HRc. Machining experiments were performed using coated carbide tools and highly cutting speed. Experimental measurements were performed for different input process parameters. The cooling capabilities are compared by monitoring of tool wear, tool life, cooling efficiency, and surface roughness. Connection between the tool wear and surface roughness is established. Experimental research show that the hard turning with carbide cutting tools and HP supply CLF provides numerous advantages from the techno-economic aspect: greater productivity, reduce of temperature in the cutting zone, improved control chip formation, extended tool life, low intensity of tool wear, surface roughness in acceptable limits, significant reduce of production costs related to the CLF.

Ventilative Cooling

DEFF Research Database (Denmark)

Heiselberg, Per Kvols; Kolokotroni, Maria

This report, by venticool, summarises the outcome of the work of the initial working phase of IEA ECB Annex 62 Ventilative Cooling and is based on the findings in the participating countries. It presents a summary of the first official Annex 62 report that describes the state-of-the-art of ventil......This report, by venticool, summarises the outcome of the work of the initial working phase of IEA ECB Annex 62 Ventilative Cooling and is based on the findings in the participating countries. It presents a summary of the first official Annex 62 report that describes the state......-of-the-art of ventilative cooling potentials and limitations, its consideration in current energy performance regulations, available building components and control strategies and analysis methods and tools. In addition, the report provides twenty six examples of operational buildings using ventilative cooling ranging from...

Task Force on Catastrophic Antiphospholipid Syndrome (APS) and Non-criteria APS Manifestations (I): catastrophic APS, APS nephropathy and heart valve lesions.

Science.gov (United States)

Cervera, R; Tektonidou, M G; Espinosa, G; Cabral, A R; González, E B; Erkan, D; Vadya, S; Adrogué, H E; Solomon, M; Zandman-Goddard, G; Shoenfeld, Y

2011-02-01

The objectives of the 'Task Force on Catastrophic Antiphospholipid Syndrome (APS) and Non-criteria APS Manifestations' were to assess the clinical utility of the international consensus statement on classification criteria and treatment guidelines for the catastrophic APS, to identify and grade the studies that analyse the relationship between the antiphospholipid antibodies and the non-criteria APS manifestations and to present the current evidence regarding the accuracy of these non-criteria APS manifestations for the detection of patients with APS. This article summarizes the studies analysed on the catastrophic APS, APS nephropathy and heart valve lesions, and presents the recommendations elaborated by the Task Force after this analysis.

Relativistic Turbulence with Strong Synchrotron and Synchrotron-Self-Compton Cooling

Science.gov (United States)

Uzdensky, D. A.

2018-03-01

Many relativistic plasma environments in high-energy astrophysics, including pulsar wind nebulae, hot accretion flows onto black holes, relativistic jets in active galactic nuclei and gamma-ray bursts, and giant radio lobes, are naturally turbulent. The plasma in these environments is often so hot that synchrotron and inverse-Compton (IC) radiative cooling becomes important. In this paper we investigate the general thermodynamic and radiative properties (and hence the observational appearance) of an optically thin relativistically hot plasma stirred by driven magnetohydrodynamic (MHD) turbulence and cooled by radiation. We find that if the system reaches a statistical equilibrium where turbulent heating is balanced by radiative cooling, the effective electron temperature tends to attain a universal value θ = kT_e/m_e c^2 ˜ 1/√{τ_T}, where τT = neσTL ≪ 1 is the system's Thomson optical depth, essentially independent of the strength of turbulent driving and hence of the magnetic field. This is because both MHD turbulent dissipation and synchrotron cooling are proportional to the magnetic energy density. We also find that synchrotron self-Compton (SSC) cooling and perhaps a few higher-order IC components are automatically comparable to synchrotron in this regime. The overall broadband radiation spectrum then consists of several distinct components (synchrotron, SSC, etc.), well separated in photon energy (by a factor ˜ τ_T^{-1}) and roughly equal in power. The number of IC peaks is checked by Klein-Nishina effects and depends logarithmically on τT and the magnetic field. We also examine the limitations due to synchrotron self-absorption, explore applications to Crab PWN and blazar jets, and discuss links to radiative magnetic reconnection.

Overview of the JET Neutral Beam Enhancement Project

International Nuclear Information System (INIS)

Ciric, D.

2006-01-01

Three objectives of the JET Neutral Beam Enhancement (NBE) are a) to increase the NB power delivered to JET from 25 MW to >34 MW; b) to extend the beam pulse duration from 10 to 20 seconds and c) to improve availability and reliability of the JET NB system. The project is based on the upgrade of the two existing JET neutral injectors, each equipped with eight positive ion neutral injectors (PINIs). The main increase of the NB power will come from the rearrangement of the ion source permanent magnets from the present supercusp to pure chequerboard configuration, thus eliminating the magnetic filter used to limit primary electrons reaching the extraction region. This modification considerably increases the fraction of molecular ions, which leads to higher neutralisation efficiency. Further increase in the injected neutral beam power will result from higher beam transmission, the consequence of high uniformity and superior properties of the beams extracted from chequerboard ion sources. Finally, the maximum extracted deuterium ion current will be increased from the present ∼ 55 A to ∼ 65 A. This will be accomplished by the minor modification of the extraction aperture diameter and the accelerator gap. All PINIs will be operated at the same acceleration voltage (125 kV). The increase of the beam pulse length from 10 to 20 seconds requires modification or replacement of inter-pulse water cooled beamline components. The most challenging among these tasks is the replacement the duct liner, which protects the vessel from re-ionised beam power at the beam entry into the torus. It will be replaced with an actively cooled liner based on proven hypervapotron technology. To improve the overall reliability of the JET neutral beam system and to allow extraction of 65 A of deuterium ion current, eight existing 80 kV/60 A high voltage power supplies (HVPS) will be replaced with four new 130 kV/130 A units. This means that, after the completion of the NBE project, 75% of the JET

Catastrophic risks and insurance in farm-level decision making

NARCIS (Netherlands)

Ogurtsov, V.

2008-01-01

Keywords: risk perception, risk attitude, catastrophic risk, insurance, farm characteristics, farmer personal characteristics, utility-efficient programming, arable farming, dairy farming

Catastrophic risks can cause severe cash flow problems for farmers or even result into their

Predicting catastrophes of non-autonomous networks with visibility graphs and horizontal visibility

Science.gov (United States)

Zhang, Haicheng; Xu, Daolin; Wu, Yousheng

2018-05-01

Prediction of potential catastrophes in engineering systems is a challenging problem. We first attempt to construct a complex network to predict catastrophes of a multi-modular floating system in advance of their occurrences. Response time series of the system can be mapped into an virtual network by using visibility graph or horizontal visibility algorithm. The topology characteristics of the networks can be used to forecast catastrophes of the system. Numerical results show that there is an obvious corresponding relationship between the variation of topology characteristics and the onset of catastrophes. A Catastrophe Index (CI) is proposed as a numerical indicator to measure a qualitative change from a stable state to a catastrophic state. The two approaches, the visibility graph and horizontal visibility algorithms, are compared by using the index in the reliability analysis with different data lengths and sampling frequencies. The technique of virtual network method is potentially extendable to catastrophe predictions of other engineering systems.

Catastrophic avalanches and methods of their control

Directory of Open Access Journals (Sweden)

N. A. Volodicheva

2014-01-01

Full Text Available Definition of such phenomenon as “catastrophic avalanche” is presented in this arti-cle. Several situations with releases of catastrophic avalanches in mountains of Caucasus, Alps, and Central Asia are investigated. Materials of snow-avalanche ob-servations performed since 1960s at the Elbrus station of the Lomonosov Moscow State University (Central Caucasus were used for this work. Complex-valued measures of engineering protection demonstrating different efficiencies are consid-ered.

Pricing catastrophic bonds for earthquakes in Mexico

OpenAIRE

Cabrera, Brenda López

2006-01-01

After the occurrence of a natural disaster, the reconstruction can be financed with catastrophic bonds (CAT bonds) or reinsurance. For insurers, reinsurers and other corporations CAT bonds provide multi year protection without the credit risk present in reinsurance. For investors CAT bonds offer attractive returns and reduction of portfolio risk, since CAT bonds defaults are uncorrelated with defaults of other securities. As the study of natural catastrophe models plays an important role in t...

Optimal natural resources management under uncertainty with catastrophic risk

Energy Technology Data Exchange (ETDEWEB)

Motoh, Tsujimura [Graduate School of Economics, Kyoto University, Yoshida-honmochi, Sakyo-ku, Kyoto 606-8501 (Japan)

2004-05-01

We examine an optimal natural resources management problem under uncertainty with catastrophic risk and investigate the optimal rate of use of a natural resource. For this purpose, we use stochastic control theory. We assume that, until a catastrophic event occurs, the stock of the natural resource is governed by a stochastic differential equation. We describe the catastrophic phenomenon as a Poisson process. From this analysis, we show the optimal rate of use of the natural resource in explicit form. Furthermore, we present comparative static results for the optimal rate of use of the natural resource.

Optimal natural resources management under uncertainty with catastrophic risk

International Nuclear Information System (INIS)

Motoh, Tsujimura

2004-01-01

We examine an optimal natural resources management problem under uncertainty with catastrophic risk and investigate the optimal rate of use of a natural resource. For this purpose, we use stochastic control theory. We assume that, until a catastrophic event occurs, the stock of the natural resource is governed by a stochastic differential equation. We describe the catastrophic phenomenon as a Poisson process. From this analysis, we show the optimal rate of use of the natural resource in explicit form. Furthermore, we present comparative static results for the optimal rate of use of the natural resource

A Theoretical Model of X-Ray Jets from Young Stellar Objects

Energy Technology Data Exchange (ETDEWEB)

Takasao, Shinsuke; Suzuki, Takeru K. [Department of Physics, Nagoya University, Nagoya, Aichi 464-8602 (Japan); Shibata, Kazunari, E-mail: takasao@kwasan.kyoto-u.ac.jp [Kwasan and Hida Observatories, Kyoto University, Yamashina, Kyoto 607-8471 (Japan)

2017-09-20

There is a subclass of X-ray jets from young stellar objects that are heated very close to the footpoint of the jets, particularly DG Tau jets. Previous models have attributed the strong heating to shocks in the jets. However, the mechanism that localizes the heating at the footpoint remains puzzling. We presented a different model of such X-ray jets, in which the disk atmosphere is magnetically heated. Our disk corona model is based on the so-called nanoflare model for the solar corona. We show that the magnetic heating near the disks can result in the formation of a hot corona with a temperature of ≳10{sup 6} K, even if the average field strength in the disk is moderately weak, ≳1 G. We determine the density and the temperature at the jet base by considering the energy balance between the heating and cooling. We derive the scaling relations of the mass-loss rate and terminal velocity of jets. Our model is applied to the DG Tau jets. The observed temperature and estimated mass-loss rate are consistent with the prediction of our model in the case of a disk magnetic field strength of ∼20 G and a heating region of <0.1 au. The derived scaling relation of the temperature of X-ray jets could be a useful tool for estimating the magnetic field strength. We also find that the jet X-ray can have a significant impact on the ionization degree near the disk surface and the dead zone size.

Stagewise cognitive development: an application of catastrophe theory.

Science.gov (United States)

van der Maas, H L; Molenaar, P C

1992-07-01

In this article an overview is given of traditional methodological approaches to stagewise cognitive developmental research. These approaches are evaluated and integrated on the basis of catastrophe theory. In particular, catastrophe theory specifies a set of common criteria for testing the discontinuity hypothesis proposed by Piaget. Separate criteria correspond to distinct methods used in cognitive developmental research. Such criteria are, for instance, the detection of spurts in development, bimodality of test scores, and increased variability of responses during transitional periods. When a genuine stage transition is present, these criteria are expected to be satisfied. A revised catastrophe model accommodating these criteria is proposed for the stage transition in cognitive development from the preoperational to the concrete operational stage.

Indirect Catastrophic Injuries in Olympic Styles of Wrestling in Iran

OpenAIRE

Kordi, Ramin; Ziaee, Vahid; Rostami, Mohsen; Wallace, W. Angus

2011-01-01

Background: Data on indirect catastrophic injuries in wrestling are scarce. Objectives: To develop a profile of indirect catastrophic injuries in international styles of wrestling and to describe possible risk factors. Study Design: Retrospective case series; Level of evidence, 3. Methods: Indirect catastrophic injuries that occurred in wrestling clubs in Iran from July 1998 to June 2005 were identified by contacting several sources. The cases were retrospectively reviewed. Results: The injur...

Reactor accidents and nuclear catastrophes

International Nuclear Information System (INIS)

Kirchhoff, R.; Linde, H.J.

1979-01-01

Assuming some preliminary knowledge of the fundamentals of atomic physics, the book describes the effects of ionizing radiation on the human organism. In order to assess the potential hazards of reactor accidents and the extent of a nuclear catastrophe, the technology of power generation in nuclear power stations is presented together with its potential dangers as well as the physical and medical processes occurring during a nuclear weapons explosion. The special medical aspects are presented which range from first aid in the case of a catastrophe to the accute radiation syndrome, the treatment of burns to the therapy of late radiolesions. Finally, it is confirmed that the treatment of radiation injured persons does not give rise to basically new medical problems. (orig./HP) [de

Abrasive water jet drilling of cooling holes in aeroengines: preliminary experimental study

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Zlámal, T.; Sitek, Libor

2018-01-01

Roč. 1, č. 1 (2018), s. 2218-2222 ISSN 1803-1269 R&D Projects: GA MŠk(CZ) LO1406; GA MPO(CZ) FV10446 Institutional support: RVO:68145535 Keywords : abrasive water jet * drilling * thermal barrier coating Subject RIV: JQ - Machines ; Tools OBOR OECD: Mechanical engineering http://www.mmscience.eu/2018.html

Measurement and analysis of the re-wetting front velocity during quench cooling of hot horizontal tubes

Energy Technology Data Exchange (ETDEWEB)

Takrouri, Kifah, E-mail: takroukj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Luxat, John, E-mail: luxatj@mcmaster.ca [Department of Engineering Physics, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Hamed, Mohamed [Thermal Processing Laboratory (TPL), Department of Mechanical Engineering, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada)

2017-01-15

Highlights: • Two phase flow & re-wetting front velocity were studied for quench of hot tubes. • The velocity decreased as temperature difference between tube and coolant decreased. • Increasing surface curvature was found to decrease the re-wetting front velocity. • Increasing tube thermal conductivity decreased the velocity. • Correlations were developed to predict the front velocity. - Abstract: When a liquid is put into contact with a hot dry surface, there exists a maximum temperature called the re-wetting temperature below which the liquid is in actual contact with the surface. Re-wetting occurs after destabilization of a vapor film that exists between the hot surface and the liquid. If re-wetting is established at a location on the hot surface, a wet patch appears at that location and starts to spread to cover and cool the entire surface. The outer edge of the wet patch is called the re-wetting front and can proceed only if the surface ahead of it cools down to the re-wetting temperature. Study of re-wetting heat transfer is very important in nuclear reactor safety for limiting the extent of core damage during the early stages of severe accidents after loss of coolant accidents LOCA and is essential for predicting the rate at which the coolant cools an overheated core. One of the important parameters in re-wetting cooling is the velocity at which the re-wetting front moves on the surface. In this study, experimental tests were carried out to investigate the re-wetting front velocity on hot horizontal cylindrical tubes being cooled by a vertical rectangular water multi-jet system. Effects of initial surface temperature in the range 400–740 °C, water subcooling in the range 15–80 °C and jet velocity in the range 0.17–1.43 m/s on the re-wetting front velocity were investigated. The two-phase flow behavior was observed by using a high-speed camera. The re-wetting front velocity was found to increase by increasing water subcooling, decreasing

Gas jet disruption mitigation studies on Alcator C-Mod

International Nuclear Information System (INIS)

Granetz, R.; Whyte, D.G.; Izzo, V.A.; Biewer, T.; Reinke, M.L.; Terry, J.; Bader, A.; Bakhtiari, M.; Jernigan, T.; Wurden, G.

2006-01-01

Damaging effects of disruptions are a major concern for Alcator C-Mod, ITER and future tokamak reactors. High-pressure noble gas jet injection is a mitigation technique which potentially satisfies the operational requirements of fast response time and reliability, while still being benign to subsequent discharges. Disruption mitigation experiments using an optimized gas jet injection system are being carried out on Alcator C-Mod to study the physics of gas jet penetration into high pressure plasmas, as well as the ability of the gas jet impurities to convert plasma energy into radiation on timescales consistent with C-Mod's fast quench times, and to reduce halo currents given C-Mod's high-current density. The dependence of impurity penetration and effectiveness on noble gas species (He, Ne, Ar, Kr) is also being studied. It is found that the high-pressure neutral gas jet does not penetrate deeply into the C-Mod plasma, and yet prompt core thermal quenches are observed on all gas jet shots. 3D MHD modelling of the disruption physics with NIMROD shows that edge cooling of the plasma triggers fast growing tearing modes which rapidly produce a stochastic region in the core of the plasma and loss of thermal energy. This may explain the apparent effectiveness of the gas jet in C-Mod despite its limited penetration. The higher-Z gases (Ne, Ar, Kr) also proved effective at reducing halo currents and decreasing thermal deposition to the divertor surfaces. In addition, noble gas jet injection proved to be benign for plasma operation with C-Mod's metal (Mo) wall, actually improving the reliability of the startup in the following discharge

The Effect Of Different Micro-Jet Streams Number On Plastic Properties Of Welds

OpenAIRE

Hadryś D.; Węgrzyn T.; Piwnik J.

2015-01-01

The main goal of that paper was analysing of plastic properties of welds made with micro-jet cooling. New technology of micro-jet welding could be regarded as a new way to improve plastic properties of welds. It allows to obtain welds with better properties in comparison to ordinary welding method. Moreover, it is possible to steering of weld structure and properties of the weld. During research Erichsen cupping tests and bending tests were carried out for welds made by MIG method with micro-...

Modern precise high-power water-cooling systems for press quenching

Directory of Open Access Journals (Sweden)

A. Patejuk

2009-04-01

Full Text Available Demand for extrusions in transport applications is increasing rapidly. The extrusions must be strong, light, crashworthy and may have to undergo hydroforming. This implies low wall thicknesses (1-2½ mm in strong alloys that need very fast quenching to obtain the required T4 temper. Crashworth iness – the ability to absorb a lot of energy in crushing deformation – demands very uniform properties throughout the section, and so does hydroforming. Various systems of water or air/water jets, with and without scanning, with and withoutarrangements for precisely aiming the jets, have proved effective for less difficult alloys in wall thicknesses down to 3 mm. These areunsuitable for the new types of transport extrusions, either inducing physical distortion or non-uniform mechanical properties. A novelcooling system that satisfies the new requirements uses laminar water jets of 50-250 μm diameter in a densely packed array of up to10/cm2. These are arranged in modules whose position and direction of aim can be adjusted relative to the part of the extrusion they cool,assuring linear cooling of all parts of the section at up to 500 K/s. The array of modules is very compact and not expensive. A sophisticated system of water microfiltration ensures that the fine nozzles do not become blocked.

Characterization of a steam plasma jet at atmospheric pressure

International Nuclear Information System (INIS)

Ni Guohua; Zhao Peng; Cheng Cheng; Song Ye; Meng Yuedong; Toyoda, Hirotaka

2012-01-01

An atmospheric steam plasma jet generated by an original dc water plasma torch is investigated using electrical and spectroscopic techniques. Because it directly uses the water used for cooling electrodes as the plasma-forming gas, the water plasma torch has high thermal efficiency and a compact structure. The operational features of the water plasma torch and the generation of the steam plasma jet are analyzed based on the temporal evolution of voltage, current and steam pressure in the arc chamber. The influence of the output characteristics of the power source, the fluctuation of the arc and current intensity on the unsteadiness of the steam plasma jet is studied. The restrike mode is identified as the fluctuation characteristic of the steam arc, which contributes significantly to the instabilities of the steam plasma jet. In addition, the emission spectroscopic technique is employed to diagnose the steam plasma. The axial distributions of plasma parameters in the steam plasma jet, such as gas temperature, excitation temperature and electron number density, are determined by the diatomic molecule OH fitting method, Boltzmann slope method and H β Stark broadening, respectively. The steam plasma jet at atmospheric pressure is found to be close to the local thermodynamic equilibrium (LTE) state by comparing the measured electron density with the threshold value of electron density for the LTE state. Moreover, based on the assumption of LTE, the axial distributions of reactive species in the steam plasma jet are estimated, which indicates that the steam plasma has high chemical activity.

Microtubule catastrophe and rescue.

Science.gov (United States)

Gardner, Melissa K; Zanic, Marija; Howard, Jonathon

2013-02-01

Microtubules are long cylindrical polymers composed of tubulin subunits. In cells, microtubules play an essential role in architecture and motility. For example, microtubules give shape to cells, serve as intracellular transport tracks, and act as key elements in important cellular structures such as axonemes and mitotic spindles. To accomplish these varied functions, networks of microtubules in cells are very dynamic, continuously remodeling through stochastic length fluctuations at the ends of individual microtubules. The dynamic behavior at the end of an individual microtubule is termed 'dynamic instability'. This behavior manifests itself by periods of persistent microtubule growth interrupted by occasional switching to rapid shrinkage (called microtubule 'catastrophe'), and then by switching back from shrinkage to growth (called microtubule 'rescue'). In this review, we summarize recent findings which provide new insights into the mechanisms of microtubule catastrophe and rescue, and discuss the impact of these findings in regards to the role of microtubule dynamics inside of cells. Copyright © 2012 Elsevier Ltd. All rights reserved.

Obstetric antecedents to body-cooling treatment of the newborn infant.

Science.gov (United States)

Nelson, David B; Lucke, Ashley M; McIntire, Donald D; Sánchez, Pablo J; Leveno, Kenneth J; Chalak, Lina F

2014-08-01

Obstetric antecedents were analyzed in births in which the infant received whole-body cooling for neonatal encephalopathy. This retrospective cohort study included all live-born singleton infants delivered at or beyond 36 weeks' gestation from October 2005 through December 2011. Infants who had received whole-body cooling identified by review of a prospective neonatal registry were compared with a control group comprising the remaining obstetric population delivered at greater than 36 weeks but not cooled. Univariable analysis was followed up by a staged, stepwise selection of variables with the intent to rank significant risk factors for cooling. A total of 86,371 women delivered during the study period and 98 infants received whole-body cooling (1.1 per 1000 live births). Of these 98 infants, 80 newborns (88%) had moderate encephalopathy and 10 (12%) had severe encephalopathy prior to cooling. Maternal age of 15 years or younger, low parity, maternal body habitus (body mass index of ≥40 kg/m(2)), diabetes, preeclampsia, induction, epidural analgesia, chorioamnionitis, length of labor, and mode of delivery were associated with significantly increased risk of infant cooling during a univariable analysis. Catastrophic events to include umbilical cord prolapse (odds ratio [OR], 14; 95% confidence interval [CI], 3-72), placental abruption (OR, 17; 95% CI, 7-44), uterine rupture (OR, 130; 95% CI, 11-1477) were the strongest factors associated with infant cooling after staged-stepwise logistic analysis. A variety of intrapartum characteristics were associated with infant cooling for neonatal encephalopathy, with the most powerful antecedents being umbilical cord prolapse, placental abruption, and uterine rupture. Copyright © 2014 Mosby, Inc. All rights reserved.

Pain catastrophizing predicts verbal expression among children with chronic pain and their mothers

Directory of Open Access Journals (Sweden)

Shelby L Langer

2016-03-01

Full Text Available This study examined intra- and inter-personal associations between pain catastrophizing and verbal expression in 70 children with recurrent abdominal pain and their mothers. Participants independently completed the Pain Catastrophizing Scale. Mothers and children then talked about the child’s pain. Speech was categorized using a linguistic analysis program. Catastrophizing was positively associated with the use of negative emotion words by both mothers and children. In addition, mothers’ catastrophizing was positively associated with both mothers’ and children’s anger word usage, whereas children’s catastrophizing was inversely associated with mothers’ anger word usage. Findings extend the literature on behavioral and interpersonal aspects of catastrophizing.

A saw-tooth plasma actuator for film cooling efficiency enhancement of a shaped hole

Science.gov (United States)

Li, Guozhan; Yu, Jianyang; Liu, Huaping; Chen, Fu; Song, Yanping

2017-08-01

This paper reports the large eddy simulations of the effects of a saw-tooth plasma actuator and the laidback fan-shaped hole on the film cooling flow characteristics, and the numerical results are compared with a corresponding standard configuration (cylindrical hole without the saw-tooth plasma actuator). For this numerical research, the saw-tooth plasma actuator is installed just downstream of the cooling hole and a phenomenological plasma model is employed to provide the 3D plasma force vectors. The results show that thanks to the downward force and the momentum injection effect of the saw-tooth plasma actuator, the cold jet comes closer to the wall surface and extends further downstream. The saw-tooth plasma actuator also induces a new pair of vortex which weakens the strength of the counter-rotating vortex pair (CRVP) and entrains the coolant towards the wall, and thus the diffusion of the cold jet in the crossflow is suppressed. Furthermore, the laidback fan-shaped hole reduces the vertical jet velocity causing the disappearance of downstream spiral separation node vortices, this compensates for the deficiency of the saw-tooth plasma actuator. Both effects of the laidback fan-shaped hole and the saw-tooth plasma actuator effectively control the development of the CRVP whose size and strength are smaller than those of the anti-counter rotating vortex pair in the far field, thus the centerline and the spanwise-averaged film cooling efficiency are enhanced. The average film cooling efficiency is the biggest in the Fan-Dc = 1 case, which is 80% bigger than that in the Fan-Dc = 0 case and 288% bigger than that in the Cyl-Dc = 0 case.

Cooling water injection system

International Nuclear Information System (INIS)

Inai, Nobuhiko.

1989-01-01

In a BWR type reactor, ECCS system is constituted as a so-called stand-by system which is not used during usual operation and there is a significant discontinuity in relation with the usual system. It is extremely important that ECCS operates upon occurrence of accidents just as specified. In view of the above in the present invention, the stand-by system is disposed along the same line with the usual system. That is, a driving water supply pump for supplying driving water to a jet pump is driven by a driving mechanism. The driving mechanism drives continuously the driving water supply pump in a case if an expected accident such as loss of the function of the water supply pump, as well as during normal operation. That is, all of the water supply pump, jet pump, driving water supply pump and driving mechanism therefor are caused to operate also during normal operation. The operation of them are not initiated upon accident. Thus, the cooling water injection system can perform at high reliability to remarkably improve the plant safety. (K.M.)

'Performative narrativity': Palestinian identity and the performance of catastrophe

NARCIS (Netherlands)

Saloul, I.

2008-01-01

The day Israel annually celebrates as its "Day of Independence" Palestinians commemorate as their day of catastrophe (al-nakba). To most Palestinians, the catastrophic loss of Palestine in 1948 represents the climactic formative event of their lives. In the aftermath of this loss, the Palestinian

The Catalan version of the Pain Catastrophizing Scale: a useful instrument to assess catastrophic thinking in whiplash patients.

Science.gov (United States)

Miró, Jordi; Nieto, Rubén; Huguet, Anna

2008-05-01

The main aims of this work were to test the psychometric properties of the Catalan version of the Pain Catastrophizing Scale (PCS) and to assess the usefulness of the scale when used with whiplash patients. This article reports results from 2 complementary studies. In the first one, the PCS was administered to 280 students and 146 chronic pain patients to examine the psychometric properties of a new Catalan version of the instrument. A confirmatory factor analysis supported a second-order structure, in which 3 second-order factors (ie, rumination, helplessness, and magnification) load in a higher-order factor (ie, catastrophizing). The reliability of the Catalan version was supported by an acceptable internal consistency and test-retest values. Validity was supported by the correlations found among the PCS and pain intensity, pain interference, and depression. The objective of the second study was to evaluate the PCS when used with whiplash patients. In this second study, 141 patients with whiplash disorders participated. In general, the psychometric properties of the PCS were found appropriate, with factor analysis supporting the structure described in patients with chronic pain. Our data suggest that the PCS is a good instrument to assess catastrophic thinking in whiplash patients. The usefulness of the PCS in whiplash disorders has been explored in this study. Results of our work show that the PCS can be a very useful tool to assess catastrophic thinking about pain in whiplash patients.

Environmental Life Cycle Assessment of Coal-Biomass to Liquid Jet Fuel Compared to Petroleum-Derived JP-8 Jet Fuel

Science.gov (United States)

2010-03-01

is a Metal Deactivator Additive (MDA) to prevent fuel oxidation with trace metals such as copper or zinc that may be in the jet fuel (MIL- HDBK-510-1...react in the FT synthesis process). The gasifier is of the slagging type and a direct contact water quench spray system is used to cool the syngas...exiting the gasifier. The quench also removes particulate matter and contaminants not removed in the slag . However, because the ash from biomass is

Turbulent Jet Flames Into a Vitiated Coflow. PhD Thesis awarded Spring 2003

Science.gov (United States)

Holdeman, James D. (Technical Monitor); Cabra, Ricardo

2004-01-01

Examined is the vitiated coflow flame, an experimental condition that decouples the combustion processes of flows found in practical combustors from the associated recirculating fluid mechanics. The configuration consists of a 4.57 mm diameter fuel jet into a coaxial flow of hot combustion products from a lean premixed flame. The 210 mm diameter coflow isolates the jet flame from the cool ambient, providing a hot environment similar to the operating conditions of advanced combustors; this important high temperature element is lacking in the traditional laboratory experiments of jet flames into cool (room) air. A family of flows of increasing complexity is presented: 1) nonreacting flow, 2) all hydrogen flame (fuel jet and premixed coflow), and 3) set of methane flames. This sequence of experiments provides a convenient ordering of validation data for combustion models. Laser Raman-Rayleigh-LIF diagnostics at the Turbulent Diffusion Flame laboratory of Sandia National Laboratories produced instantaneous multiscalar point measurements. These results attest to the attractive features of the vitiated coflow burner and the well-defined boundary conditions provided by the coflow. The coflow is uniform and steady, isolating the jet flame from the laboratory air for a downstream distance ranging from z/d = 50-70. The statistical results show that differential diffusion effects in this highly turbulent flow are negligible. Complementing the comprehensive set of multiscalar measurements is a parametric study of lifted methane flames that was conducted to analyze flame sensitivity to jet and coflow velocity, as well as coflow temperature. The linear relationship found between the lift-off height and the jet velocity is consistent with previous experiments. New linear sensitivities were found correlating the lift-off height to coflow velocity and temperature. A blow-off study revealed that the methane flame blows off at a common coflow temperature (1260 K), regardless of

A critical look at catastrophe risk assessments

CERN Document Server

Kent, A

2004-01-01

Recent papers by Busza et al. (BJSW) and Dar et al. (DDH) argue that astrophysical data can be used to establish bounds on the risk of a catastrophe in forthcoming collider experiments. The safety case set out by BJSW does not rely on these bounds, but on theoretical arguments, which BJSW find sufficiently compelling. However, DDH and other commentators (initially including BJSW) have suggested that the astrophysical bounds alone do give sufficient reassurance. This seems unsupportable when the bounds are expressed in terms of expected cost. For example, DDH's main bound, $p_{\\rm catastrophe} < 2 \\times 10^{-8}$, implies only that the expectation value of the number of deaths is bounded by 120. We thus reappraise the DDH and BJSW risk bounds by comparing risk policy in other areas. We find that requiring a catastrophe risk of no higher than 10^{-15} is necessary to be consistent with established policy for risk optimisation from radiation hazards, even if highly risk tolerant assumptions are made. A respec...

[Bioethics in catastrophe situations such as earthquakes].

Science.gov (United States)

León, C Francisco Javier

2012-01-01

A catastrophe of the magnitude of the earthquake and tsunami that hit Chile not long ago, forces us to raise some questions that we will try to answer from a philosophical, ethical and responsibility viewpoints. An analysis of the basic principles of bioethics is also justified. A natural catastrophe is not, by itself, moral or immoral, fair or unfair. However, its consequences could certainly be regarded as such, depending on whether they could have been prevented or mitigated. We will identify those individuals, who have the ethical responsibility to attend the victims and the ethical principles that must guide the tasks of healthcare and psychological support teams. The minimal indispensable actions to obtain an adequate social and legal protection of vulnerable people, must be defined according to international guidelines. These reflections are intended to improve the responsibility of the State and all the community, to efficiently prevent and repair the material and psychological consequences of such a catastrophe.

Pricing the property claim service (PCS) catastrophe insurance options using gamma distribution

Science.gov (United States)

Noviyanti, Lienda; Soleh, Achmad Zanbar; Setyanto, Gatot R.

2017-03-01

The catastrophic events like earthquakes, hurricanes or flooding are characteristics for some areas, a properly calculated annual premium would be closely as high as the loss insured. From an actuarial perspective, such events constitute the risk that are not insurable. On the other hand people living in such areas need protection. In order to securitize the catastrophe risk, futures or options based on a loss index could be considered. Chicago Board of Trade launched a new class of catastrophe insurance options based on new indices provided by Property Claim Services (PCS). The PCS-option is based on the Property Claim Service Index (PCS-Index). The index are used to determine and payout in writing index-based insurance derivatives. The objective of this paper is to price PCS Catastrophe Insurance Option based on PCS Catastrophe index. Gamma Distribution is used to estimate PCS Catastrophe index distribution.

Pain Catastrophizing Correlates with Early Mild Traumatic Brain Injury Outcome

Directory of Open Access Journals (Sweden)

Geneviève Chaput

2016-01-01

Full Text Available Background. Identifying which patients are most likely to be at risk of chronic pain and other postconcussion symptoms following mild traumatic brain injury (MTBI is a difficult clinical challenge. Objectives. To examine the relationship between pain catastrophizing, defined as the exaggerated negative appraisal of a pain experience, and early MTBI outcome. Methods. This cross-sectional design included 58 patients diagnosed with a MTBI. In addition to medical chart review, postconcussion symptoms were assessed by self-report at 1 month (Time 1 and 8 weeks (Time 2 after MTBI. Pain severity, psychological distress, level of functionality, and pain catastrophizing were measured by self-report at Time 2. Results. The pain catastrophizing subscales of rumination, magnification, and helplessness were significantly correlated with pain severity (r=.31 to .44, number of postconcussion symptoms reported (r=.35 to .45, psychological distress (r=.57 to .67, and level of functionality (r=-.43 to -.29. Pain catastrophizing scores were significantly higher for patients deemed to be at high risk of postconcussion syndrome (6 or more symptoms reported at both Time 1 and Time 2. Conclusions. Higher levels of pain catastrophizing were related to adverse early MTBI outcomes. The early detection of pain catastrophizing may facilitate goal-oriented interventions to prevent or minimize the development of chronic pain and other postconcussion symptoms.

Atmospheric emissions from power plant cooling towers

International Nuclear Information System (INIS)

Micheletti, W.

2006-01-01

Power plant recirculated cooling systems (cooling towers) are not typically thought of as potential sources of air pollution. However, atmospheric emissions can be important considerations that may influence cooling tower design and operation. This paper discusses relevant U.S. environmental regulations for potential atmospheric pollutants from power plant cooling towers, and various methods for estimating and controlling these emissions. (orig.)

An experimental study of the supersonic, dual, coaxial jets impinging on an inclined flat plate

International Nuclear Information System (INIS)

Kim, Jung Bae; Lee, Jun Hee; Woo, Sun Hoon; Kim, Heuy Dong

2002-01-01

The impinging supersonic jets have been applied for rocket launching system, thrust control, gas turbine blade cooling, etc. Recently the supersonic, dual, coaxial jets are being extensively used in many diverse fields of industrial processes since they lead to more improved performance, compared with the conventional supersonic jets impinging on an object. In the present study, experimentation is carried out to investigate the supersonic, dual, coaxial jets impinging on an inclined flat plate. A convergent-divergent nozzle with a design Mach number of 2.0 and annular sonic nozzle are used to make the dual, coaxial jet flows. The angle of the impinging flat plate is varied from 30 .deg. to 60 .deg. and the distance between the dual coaxial nozzle and flat plate is also varied. Detailed pressures on the impinging plate are measured to analyze the flow fields, which are also visualized using Schlieren optical method

Time-frequency analysis of submerged synthetic jet

Science.gov (United States)

Kumar, Abhay; Saha, Arun K.; Panigrahi, P. K.

2017-12-01

The coherent structures transport the finite body of fluid mass through rolling which plays an important role in heat transfer, boundary layer control, mixing, cooling, propulsion and other engineering applications. A synthetic jet in the form of a train of vortex rings having coherent structures of different length scales is expected to be useful in these applications. The propagation and sustainability of these coherent structures (vortex rings) in downstream direction characterize the performance of synthetic jet. In the present study, the velocity signal acquired using the S-type hot-film probe along the synthetic jet centerline has been taken for the spectral analysis. One circular and three rectangular orifices of aspect ratio 1, 2 and 4 actuating at 1, 6 and 18 Hz frequency have been used for creating different synthetic jets. The laser induced fluorescence images are used to study the flow structures qualitatively and help in explaining the velocity signal for detection of coherent structures. The study depicts four regions as vortex rollup and suction region (X/D h ≤ 3), steadily translating region (X/D h ≤ 3-8), vortex breakup region (X/Dh ≤ 4-8) and dissipation of small-scale vortices (X/D h ≤ 8-15). The presence of coherent structures localized in physical and temporal domain is analyzed for the characterization of synthetic jet. Due to pulsatile nature of synthetic jet, analysis of velocity time trace or signal in time, frequency and combined time-frequency domain assist in characterizing the signatures of coherent structures. It has been observed that the maximum energy is in the first harmonic of actuation frequency, which decreases slowly in downstream direction at 6 Hz compared to 1 and 18 Hz of actuation.

S. pombe kinesins-8 promote both nucleation and catastrophe of microtubules.

Directory of Open Access Journals (Sweden)

Muriel Erent

Full Text Available The kinesins-8 were originally thought to be microtubule depolymerases, but are now emerging as more versatile catalysts of microtubule dynamics. We show here that S. pombe Klp5-436 and Klp6-440 are non-processive plus-end-directed motors whose in vitro velocities on S. pombe microtubules at 7 and 23 nm s(-1 are too slow to keep pace with the growing tips of dynamic interphase microtubules in living S. pombe. In vitro, Klp5 and 6 dimers exhibit a hitherto-undescribed combination of strong enhancement of microtubule nucleation with no effect on growth rate or catastrophe frequency. By contrast in vivo, both Klp5 and Klp6 promote microtubule catastrophe at cell ends whilst Klp6 also increases the number of interphase microtubule arrays (IMAs. Our data support a model in which Klp5/6 bind tightly to free tubulin heterodimers, strongly promoting the nucleation of new microtubules, and then continue to land as a tubulin-motor complex on the tips of growing microtubules, with the motors then dissociating after a few seconds residence on the lattice. In vivo, we predict that only at cell ends, when growing microtubule tips become lodged and their growth slows down, will Klp5/6 motor activity succeed in tracking growing microtubule tips. This mechanism would allow Klp5/6 to detect the arrival of microtubule tips at cells ends and to amplify the intrinsic tendency for microtubules to catastrophise in compression at cell ends. Our evidence identifies Klp5 and 6 as spatial regulators of microtubule dynamics that enhance both microtubule nucleation at the cell centre and microtubule catastrophe at the cell ends.

Numerical study of an impinging jet to a turbulent channel flow in a T-Junction configuration

Science.gov (United States)

Georgiou, Michail; Papalexandris, Miltiadis

2016-11-01

In this talk we report on Large Eddy Simulations of an impinging planar jet to a turbulent channel flow in a T-Junction configuration. Due to its capacity for mixing and heat transfer enhancement, this type of flow is encountered in various industrial applications. In particular, our work is related to the emergency cooling systems of pressurized water reactors. As is well known, this type of flow is dominated by a large separation bubble downstream the jet impingement location. Secondary regions of flow separation are predicted both upstream and downstream the impinging jet. We describe how these separation regions interact with the shear layer that is formed by the injection of the jet to the crossflow, and how they affect the mixing process. In our talk we further examine the influence of the jet's velocity to characteristic quantities of the jet, such as penetration length and expansion angle, as well as to the first and second-order statistics of the flow.

Cooling tower plume - model and experiment

Science.gov (United States)

Cizek, Jan; Gemperle, Jiri; Strob, Miroslav; Nozicka, Jiri

The paper discusses the description of the simple model of the, so-called, steam plume, which in many cases forms during the operation of the evaporative cooling systems of the power plants, or large technological units. The model is based on semi-empirical equations that describe the behaviour of a mixture of two gases in case of the free jet stream. In the conclusion of the paper, a simple experiment is presented through which the results of the designed model shall be validated in the subsequent period.

Passive containment cooling system with drywell pressure regulation for boiling water reactor

Science.gov (United States)

Hill, P.R.

1994-12-27

A boiling water reactor is described having a regulating valve for placing the wetwell in flow communication with an intake duct of the passive containment cooling system. This subsystem can be adjusted to maintain the drywell pressure at (or slightly below or above) wetwell pressure after the initial reactor blowdown transient is over. This addition to the PCCS design has the benefit of eliminating or minimizing steam leakage from the drywell to the wetwell in the longer-term post-LOCA time period and also minimizes the temperature difference between drywell and wetwell. This in turn reduces the rate of long-term pressure buildup of the containment, thereby extending the time to reach the design pressure limit. 4 figures.

Synthesis of ZnO particles in a quench-cooled flame reactor

DEFF Research Database (Denmark)

Hansen, Jens Peter; Jensen, Joakim Reimer; Livbjerg, Hans

2001-01-01

The quench cooling of a flame by injection of cold air was studied in a flame reactor for the formation of ZnO particles in a premixed flame with a precursor jet. A rapid temperature drop downstream from the temperature peak is advantageous for the attainment of a large specific surface area...

Catastrophic household expenditure on health in Nepal: a cross-sectional survey.

Science.gov (United States)

Saito, Eiko; Gilmour, Stuart; Rahman, Md Mizanur; Gautam, Ghan Shyam; Shrestha, Pradeep Krishna; Shibuya, Kenji

2014-10-01

To determine the incidence of - and illnesses commonly associated with - catastrophic household expenditure on health in Nepal. We did a cross-sectional population-based survey in five municipalities of Kathmandu Valley between November 2011 and January 2012. For each household surveyed, out-of-pocket spending on health in the previous 30 days that exceeded 10% of the household's total expenditure over the same period was considered to be catastrophic. We estimated the incidence and intensity of catastrophic health expenditure. We identified the illnesses most commonly associated with such expenditure using a Poisson regression model and assessed the distribution of expenditure by economic quintile of households using the concentration index. Overall, 284 of the 1997 households studied in Kathmandu, i.e. 13.8% after adjustment by sampling weight, reported catastrophic health expenditure in the 30 days before the survey. After adjusting for confounders, this expenditure was found to be associated with injuries, particularly those resulting from road traffic accidents. Catastrophic expenditure by households in the poorest quintile were associated with at least one episode of diabetes, asthma or heart disease. In an urban area of Nepal, catastrophic household expenditure on health was mostly associated with injuries and noncommunicable diseases such as diabetes and asthma. Throughout Nepal, interventions for the control and management of noncommunicable diseases and the prevention of road traffic accidents should be promoted. A phased introduction of health insurance should also reduce the incidence of catastrophic household expenditure.

Inclined Jet in Crossflow Interacting with a Vortex Generator

Science.gov (United States)

Zaman, K. B. M. Q.; Rigby, D .L.; Heidmann, J. D.

2011-01-01

An experiment is conducted on the effectiveness of a vortex generator in preventing liftoff of a jet in crossflow, with possible relevance to film-cooling applications. The jet issues into the boundary layer at an angle of 20 degreees to the freestream. The effect of a triangular ramp-shaped vortex generator is studied while varying its geometry and location. Detailed flowfield properties are obtained for a case in which the height of the vortex generator and the diameter of the orifice are comparable with the approach boundary-layer thickness. The vortex generator produces a streamwise vortex pair with a vorticity magnitude 3 times larger (and of opposite sense) than that found in the jet in crossflow alone. Such a vortex generator appears to be most effective in keeping the jet attached to the wall. The effect of parametric variation is studied mostly from surveys 10 diameters downstream from the orifice. Results over a range of jet-to-freestream momentum flux ratio (1 vortex generator has a significant effect even at the highest J covered in the experiment. When the vortex generator height is halved, there is a liftoff of the jet. On the other hand, when the height is doubled, the jet core is dissipated due to larger turbulence intensity. Varying the location of the vortex generator, over a distance of three diameters from the orifice, is found to have little impact. Rounding off the edges of the vortex generator with the increasing radius of curvature progressively diminishes its effect. However, allowing for a small radius of curvature may be quite tolerable in practice.

The JET belt limiter tiles

International Nuclear Information System (INIS)

Deksnis, E.

1988-09-01

The belt limiter system, comprising two full toroidal rings of limiter tiles, was installed in JET in 1987. In consists of water-cooled fins with the limiter material in form of tile inbetween. The tiles are designed to absorb heat fluxes during irradiation without the surface temperature exceeding 2000 0 C and to radiate this heat between pulses to the water cooled sink whose temperature is lower than that of the vacuum vessel. An important feature of the design is to maximise the area of the radiating surface facing the water cooled fin. This leads to a tile depth much greater than the width of the tile facing the heat flux. Limiter tiles intercept particles flowing out of the plasma through the area between the two belt limiter rings and through remaining surface area of the plasma column. Power deposition to a limiter tile depends strongly on the shape of the plasma, the edge plasma properties as well as on the surface profile of the tiles. This paper will discuss the methodology that was followed in producing an optimized surface profile of the tiles. This shaped profile has the feature that the resulting power deposition profile is roughly similar for a wide range of plasma parameters. (author)

Catastrophic Failure and Critical Scaling Laws of Fiber Bundle Material

Directory of Open Access Journals (Sweden)

Shengwang Hao

2017-05-01

Full Text Available This paper presents a spring-fiber bundle model used to describe the failure process induced by energy release in heterogeneous materials. The conditions that induce catastrophic failure are determined by geometric conditions and energy equilibrium. It is revealed that the relative rates of deformation of, and damage to the fiber bundle with respect to the boundary controlling displacement ε0 exhibit universal power law behavior near the catastrophic point, with a critical exponent of −1/2. The proportion of the rate of response with respect to acceleration exhibits a linear relationship with increasing displacement in the vicinity of the catastrophic point. This allows for the prediction of catastrophic failure immediately prior to failure by extrapolating the trajectory of this relationship as it asymptotes to zero. Monte Carlo simulations are completed and these two critical scaling laws are confirmed.

Cooling Performance of ALIP according to the Air or Sodium Cooling Type

Energy Technology Data Exchange (ETDEWEB)

Ye, Huee-Youl; Yoon, Jung; Lee, Tae-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

ALIP pumps the liquid sodium by Lorentz force produced by the interaction of induced current in the liquid metal and their associated magnetic field. Even though the efficiency of the ALIP is very low compared to conventional mechanical pumps, it is very useful due to the absence of moving parts, low noise and vibration level, simplicity of flow rate regulation and maintenance, and high temperature operation capability. Problems in utilization of ALIP concern a countermeasure for elevation of internal temperature of the coil due to joule heating and how to increase magnetic flux density of Na channel gap. The conventional ALIP usually used cooling methods by circulating the air or water. On the other hand, GE-Toshiba developed a double stator pump adopting the sodium-immersed self-cooled type, and it recovered the heat loss in sodium. Therefore, the station load factor of the plant could be reduced. In this study, the cooling performance with cooling types of ALIP is analyzed. We developed thermal analysis models to evaluate the cooling performance of air or sodium cooling type of ALIP. The cooling performance is analyzed for operating parameters and evaluated with cooling type. 1-D and 3-D thermal analysis model for IHTS ALIP was developed, and the cooling performance was analyzed for air or sodium cooling type. The cooling performance for air cooling type was better than sodium cooling type at higher air velocity than 0.2 m/s. Also, the air temperature of below 270 .deg. demonstrated the better cooling performance as compared to sodium.

Miniature Filament Eruptions and their Reconnections in X-Ray Jets: Evidence for a New Paradigm

Science.gov (United States)

Sterling, Alphonse C.; Moore, Ronald L.; Falconer, David A.

2014-01-01

We investigate the onset of approximately10 random X-ray jets observed by Hinode/XRT. Each jet was near the limb in a polar coronal hole, and showed a ``bright point'' in an edge of the base of the jet, as is typical for previously-observed X-ray jets. We examined SDO/AIA EUV images of each of the jets over multiple AIA channels, including 304 Ang, which detects chromospheric emissions, and 171, 193, and 211 Ang, which detect cooler-coronal emissions. We find the jets to result from eruptions of miniature (size less than approximately 10 arcsec) filaments from the bases of the jets. Much of the erupting-filament material forms a chromospheric-temperature jet. In the cool-coronal channels, often the filament appears in absorption and the jet in emission. The jet bright point forms at the location from which the miniature filament is ejected, analogous to the formation of a standard solar flare in the wake of the eruption of a typical larger-scale chromospheric filament. Thus these X-ray jets and their bright points are made by miniature filament eruptions. They are evidently produced the same way as an on-disk coronal jet we observed in Adams et al. (2014); that on-disk jet had no obvious emerging magnetic field in its base. We conclude that, for many jets, the standard idea of X-ray jets forming from reconnection between emerging flux and preexisting coronal field is incorrect. ACS and RLM were supported by funding from NASA/LWS, Hinode, and ISSI.

SIGNATURES OF RELATIVISTIC HELICAL MOTION IN THE ROTATION MEASURES OF ACTIVE GALACTIC NUCLEUS JETS

Energy Technology Data Exchange (ETDEWEB)

Broderick, Avery E [Canadian Institute for Theoretical Astrophysics, 60 St. George Street, Toronto, ON M5S 3H8 (Canada); Loeb, Abraham [Institute for Theory and Computation, Harvard University, Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States)

2009-10-01

Polarization has proven to be an invaluable tool for probing magnetic fields in relativistic jets. Maps of the intrinsic polarization vectors have provided the best evidence to date for uniform, toroidally dominated magnetic fields within jets. More recently, maps of the rotation measure (RM) in jets have for the first time probed the field geometry of the cool, moderately relativistic surrounding material. In most cases, clear signatures of the toroidal magnetic field are detected, corresponding to gradients in RM profiles transverse to the jet. However, in many objects, these profiles also display marked asymmetries that are difficult to explain in simple helical jet models. Furthermore, in some cases, the RM profiles are strongly frequency and/or time dependent. Here we show that these features may be naturally accounted for by including relativistic helical motion in the jet model. In particular, we are able to reproduce bent RM profiles observed in a variety of jets, frequency-dependent RM profile morphologies, and even the time dependence of the RM profiles of knots in 3C 273. Finally, we predict that some sources may show reversals in their RM profiles at sufficiently high frequencies, depending upon the ratio of the components of jet sheath velocity transverse and parallel to the jet. Thus, multi-frequency RM maps promise a novel way in which to probe the velocity structure of relativistic outflows.

The Effectiveness of Catastrophe Bonds in Portfolio Diversification

OpenAIRE

Mariani, Massimo; Amoruso, Paola

2016-01-01

The rapid growth of catastrophe bonds in financial markets is due to increasing environmental disasters and consequent economic losses, barely covered by insurance and reinsurance companies. These securities represent an effective solution, allowing the risk transfer to the capital market. The objective of this paper is to prove real advantages of the investor who operates in this market segment, in terms of portfolio diversification. The present work indeed shows how investing in catastrophe...

An application of Mean Escape Time and metapopulation on forestry catastrophe insurance

Science.gov (United States)

Li, Jiangcheng; Zhang, Chunmin; Liu, Jifa; Li, Zhen; Yang, Xuan

2018-04-01

A forestry catastrophe insurance model due to forestry pest infestations and disease epidemics is developed by employing metapopulation dynamics and statistics properties of Mean Escape Time (MET). The probability of outbreak of forestry catastrophe loss and the catastrophe loss payment time with MET are respectively investigated. Forestry loss data in China is used for model simulation. Experimental results are concluded as: (1) The model with analytical results is shown to be a better fit; (2) Within the condition of big area of patches and structure of patches, high system factor, low extinction rate, high multiplicative noises, and additive noises with a high cross-correlated strength range, an outbreak of forestry catastrophe loss or catastrophe loss payment due to forestry pest infestations and disease epidemics could occur; (3) An optimal catastrophe loss payment time MET due to forestry pest infestations and disease epidemics can be identified by taking proper value of multiplicative noises and limits the additive noises on a low range of value, and cross-correlated strength at a high range of value.

Investigation of Characteristics of Impinging Jet for 1/5-Scale ECC injection

Energy Technology Data Exchange (ETDEWEB)

Shin, Byung Soo; Ko, Yung Joo; Bae, Hwang; Kwon, Tae Soon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-05-15

In ECCS of SMART reactor, safety injection pump discharges cooling water into the core to maintain the water level by filling the amount of loss of coolant under emergency situation such as SBLOCA. Once the ECCS starts to operate, the injected water will be impinged to the upper wall of core support barrel (CBS). And the water will fall along the wall forming liquid film or droplets as shown in Fig. 1(b) due to high Reynolds number. The breakup and film flow will be bypassed by high temperature and pressure steam-water mixture cross flow from RCP discharge into the atmosphere through broken injection nozzle. Then, the flow phenomena in the downcomer is very complex situation with including jet impingement, jet breakup, liquid entrainment, steam condensation, counter-current flow and etc. In this study, the hydraulic features of impinging jet were investigated through visualization for full scale test for simulation of SMART ECC jet and SWAT test of 1/5 simulated test for ECCS of SMART reactor and measurement of the film width. And the scaling method for SWAT test was discussed considering jet break up and other phenomena

Jet mass spectra in Higgs+one jet at NNLL

International Nuclear Information System (INIS)

Jouttenus, Teppo T.; Stewart, Iain W.; Waalewijn, Wouter J.

2013-02-01

The invariant mass of a jet is a benchmark variable describing the structure of jets at the LHC. We calculate the jet mass spectrum for Higgs plus one jet at the LHC at next-to-next-to-leading logarithmic (NNLL) order using a factorization formula. At this order, the cross section becomes sensitive to perturbation theory at the soft m 2 jet /p jet T scale. Our calculation is exclusive and uses the 1-jettiness global event shape to implement a veto on additional jets. The dominant dependence on the jet veto is removed by normalizing the spectrum, leaving residual dependence from non-global logarithms depending on the ratio of the jet mass and jet veto variables. For our exclusive jet cross section these non-global logarithms are parametrically smaller than in the inclusive case, allowing us to obtain a complete NNLL result. Results for the dependence of the jet mass spectrum on the kinematics, jet algorithm, and jet size R are given. Using individual partonic channels we illustrate the difference between the jet mass spectra for quark and gluon jets. We also study the effect of hadronization and underlying event on the jet mass in Pythia. To highlight the similarity of inclusive and exclusive jet mass spectra, a comparison to LHC data is presented.

Purchase of Catastrophe Insurance by Dutch Dairy and Arable Farmers

NARCIS (Netherlands)

Ogurtsov, V.; Asseldonk, van M.A.P.M.; Huirne, R.B.M.

2009-01-01

This article analyzed the impact of risk perception, risk attitude, and other farmer personal and farm characteristics on the actual purchase of catastrophe insurance by Dutch dairy and arable farmers. The specific catastrophe insurance types considered were hail–fire–storm insurance for buildings,

Numerical simulation of heat transfer and fluid flow of an impinging round jet of plasma into confined walls

International Nuclear Information System (INIS)

Ezato, Koichiro; Shimizu, Akihiko; Kunugi, Tomoaki.

1995-01-01

Numerical simulations are presented on the flow and heat transfer characteristics of an impinging round jet of argon plasma with atmospheric pressure. The target slab with finite thickness upon which plasma jet impinges is assumed to be as SiC which is a candidate material for plasma facing material of fusion reactor. The plasma jet is treated by use of a magnetohydrodynamics model that takes its two-temperature non-equilibrium state into account. The rear side of the target slab is assumed to be cooled by a gas-solid suspension impinging round jet. The result shows that the plasma is in non-equilibrium state in which the electron temperature is higher than the heavy particle in the outer region of plasma jet core and that the heat flux to the target slab is over 8 MW/m 2 in the region of the plasma jet core contacts. (author)

Cooling tower plume - model and experiment

Directory of Open Access Journals (Sweden)

Cizek Jan

2017-01-01

Full Text Available The paper discusses the description of the simple model of the, so-called, steam plume, which in many cases forms during the operation of the evaporative cooling systems of the power plants, or large technological units. The model is based on semi-empirical equations that describe the behaviour of a mixture of two gases in case of the free jet stream. In the conclusion of the paper, a simple experiment is presented through which the results of the designed model shall be validated in the subsequent period.

Jet angularity measurements for single inclusive jet production

Science.gov (United States)

Kang, Zhong-Bo; Lee, Kyle; Ringer, Felix

2018-04-01

We study jet angularity measurements for single-inclusive jet production at the LHC. Jet angularities depend on a continuous parameter a allowing for a smooth interpolation between different traditional jet shape observables. We establish a factorization theorem within Soft Collinear Effective Theory (SCET) where we consistently take into account in- and out-of-jet radiation by making use of semi-inclusive jet functions. For comparison, we elaborate on the differences to jet angularities measured on an exclusive jet sample. All the necessary ingredients for the resummation at next-to-leading logarithmic (NLL) accuracy are presented within the effective field theory framework. We expect semiinclusive jet angularity measurements to be feasible at the LHC and we present theoretical predictions for the relevant kinematic range. In addition, we investigate the potential impact of jet angularities for quark-gluon discrimination.

Jet mass spectra in Higgs+one jet at NNLL

Energy Technology Data Exchange (ETDEWEB)

Jouttenus, Teppo T.; Stewart, Iain W. [Massachusetts Institute of Technology, Cambridge, MA (United States). Center for Theoretical Physics; Tackmann, Frank J. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Waalewijn, Wouter J. [California Univ., San Diego, La Jolla, CA (United States). Dept. of Physics

2013-02-15

The invariant mass of a jet is a benchmark variable describing the structure of jets at the LHC. We calculate the jet mass spectrum for Higgs plus one jet at the LHC at next-to-next-to-leading logarithmic (NNLL) order using a factorization formula. At this order, the cross section becomes sensitive to perturbation theory at the soft m{sup 2}{sub jet}/p{sup jet}{sub T} scale. Our calculation is exclusive and uses the 1-jettiness global event shape to implement a veto on additional jets. The dominant dependence on the jet veto is removed by normalizing the spectrum, leaving residual dependence from non-global logarithms depending on the ratio of the jet mass and jet veto variables. For our exclusive jet cross section these non-global logarithms are parametrically smaller than in the inclusive case, allowing us to obtain a complete NNLL result. Results for the dependence of the jet mass spectrum on the kinematics, jet algorithm, and jet size R are given. Using individual partonic channels we illustrate the difference between the jet mass spectra for quark and gluon jets. We also study the effect of hadronization and underlying event on the jet mass in Pythia. To highlight the similarity of inclusive and exclusive jet mass spectra, a comparison to LHC data is presented.

Pediatric catastrophic antiphospholipid syndrome: descriptive analysis of 45 patients from the "CAPS Registry".

Science.gov (United States)

Berman, Horacio; Rodríguez-Pintó, Ignasi; Cervera, Ricard; Gregory, Simone; de Meis, Ernesto; Rodrigues, Carlos Ewerton Maia; Aikawa, Nádia Emi; de Carvalho, Jozélio Freire; Springer, Janusz; Niedzwiecki, Maciej; Espinosa, Gerard

2014-02-01

Given the lack of information about catastrophic antiphospholipid syndrome (APS) in pediatric patients, the objective of the current study was to describe the clinical characteristics, laboratory features, treatment, and outcome of pediatric patients with catastrophic APS and compare them with the adult patients with catastrophic APS. We identified patients who were under 18years of age at time of catastrophic APS diagnosis included in the international registry of patients with catastrophic APS (CAPS Registry). Their main demographic and clinical characteristics, laboratory features, treatment, and outcome were described and compared with those of adult patients with catastrophic APS. From the 446 patients included in the CAPS Registry as of May 2013, 45 (10.3%) patients developed 46 catastrophic events before 18years of age (one patient presented two episodes). Overall, 32 (71.1%) patients were female and the mean age was 11.5±4.6years (range, 3months-18years). A total of 31 (68.9%) patients suffered from primary APS and 13 (28.9%) from systemic lupus erythematosus (SLE). The main differences between the two groups of patients were the higher prevalence of infections as precipitating factor for catastrophic event in the pediatric population (60.9% versus 26.8% in the adult population, p<0.001) and of peripheral vessel thrombosis (52.2% versus 34.3%, p=0.017). In addition, catastrophic APS was the first manifestation of APS more frequently in pediatric patients (86.6% versus 45.2%, p<0.001). Interestingly, pediatric patients showed a trend of lower mortality, although the difference was not statistically significant (26.1% versus 40.2%; odds ratio, 1.9; 95% confidence interval, 0.96-3.79; p=0.063). No differences were found neither in the laboratory features nor in the isolated or combination treatments between groups. Catastrophic APS in pediatric patients is a rare disease. There are minimal differences in the clinical and laboratory features, treatment, and

Experimental and computational studies of film cooling with compound angle injection

Energy Technology Data Exchange (ETDEWEB)

Goldstein, R.J.; Eckert, E.R.G.; Patankar, S.V. [Univ. of Minnesota, Minneapolis, MN (United States)] [and others

1995-10-01

The thermal efficiency of gas turbine systems depends largely on the turbine inlet temperature. Recent decades have seen a steady rise in the inlet temperature and a resulting reduction in fuel consumption. At the same time, it has been necessary to employ intensive cooling of the hot components. Among various cooling methods, film cooling has become a standard method for cooling of the turbine airfoils and combustion chamber walls. The University of Minnesota program is a combined experimental and computational study of various film-cooling configurations. Whereas a large number of parameters influence film cooling processes, this research focuses on compound angle injection through a single row and through two rows of holes. Later work will investigate the values of contoured hole designs. An appreciation of the advantages of compound angle injection has risen recently with the demand for more effective cooling and with improved understanding of the flow; this project should continue to further this understanding. Approaches being applied include: (1) a new measurement system that extends the mass/heat transfer analogy to obtain both local film cooling and local mass (heat) transfer results in a single system, (2) direct measurement of three-dimensional turbulent transport in a highly-disturbed flow, (3) the use of compound angle and shaped holes to optimize film cooling performance, and (4) an exploration of anisotropy corrections to turbulence modeling of film cooling jets.

Protocols of a catastrophe

International Nuclear Information System (INIS)

Stscherbak, J.

1988-01-01

In unusually frank terms the author, a journalist and epidemiologist, describes the catastrophe of Chernobyl as the 'most pathetic and important' experience of the Soviet people after World War II. Documents, interviews and statements of persons concerned trace the disaster of those days that surpasses imagination and describe how individual persons witnessed the coming true of visions of terror. (orig./HSCH) [de

Measurement of b-quark Jet Shapes at CDF

Energy Technology Data Exchange (ETDEWEB)

Lister, Alison [Univ. of Oxford (United Kingdom)

2006-01-01

large systematic uncertainties, the measured b-quark jet shapes are significantly different from those expected from the so-called Pythia Tune A Monte Carlo simulation, the most widely used Leading Order Monte Carlo model at CDF. This difference can be mostly attributed to the fact that the fraction of b-quark jets that originate from flavour creation (where a single b-quark is expected inside the same jet cone) over those that originate from gluon splitting (where two b-quarks are expected to be inside the same jet cone) is slightly different in the Pythia Tune A Monte Carlo predictions than in data. This measurement can help in the tuning of the fraction of gluon splitting to flavour creation b-quark jets in the Monte Carlo simulation. This tuning is particularly important for the extrapolation up to LHC energies where many searches will involve b-quark jets. During the first year of my thesis work, I worked on the implementation of a prototype detector control system for the electromagnetic calorimeter which is being built for the CMS experiment at CERN. The prototype which I implemented was used to monitor and control the high voltage, low voltage, cooling and precision temperature monitoring systems during the summer 2003 test-beam. This was one of the first, almost complete, systems implemented and used by an LHC experiment for test-beam monitoring.

Impact of red giant/AGB winds on active galactic nucleus jet propagation

Science.gov (United States)

Perucho, M.; Bosch-Ramon, V.; Barkov, M. V.

2017-10-01

Context. Dense stellar winds may mass-load the jets of active galactic nuclei, although it is unclear on what time and spatial scales the mixing takes place. Aims: Our aim is to study the first steps of the interaction between jets and stellar winds, and also the scales on which the stellar wind mixes with the jet and mass-loads it. Methods: We present a detailed 2D simulation - including thermal cooling - of a bubble formed by the wind of a star designed to study the initial stages of jet-star interaction. We also study the first interaction of the wind bubble with the jet using a 3D simulation in which the star enters the jet. Stability analysis is carried out for the shocked wind structure to evaluate the distances over which the jet-dragged wind, which forms a tail, can propagate without mixing with the jet flow. Results.The 2D simulations point to quick wind bubble expansion and fragmentation after about one bubble shock crossing time. Three-dimensional simulations and stability analysis point to local mixing in the case of strong perturbations and relatively low density ratios between the jet and the jet dragged-wind, and to a possibly more stable shocked wind structure at the phase of maximum tail mass flux. Analytical estimates also indicate that very early stages of the star jet-penetration time may be also relevant for mass-loading. The combination of these and previous results from the literature suggests highly unstable interaction structures and efficient wind-jet flow mixing on the scale of the jet interaction height. Conclusions: The winds of stars with strong mass loss can efficiently mix with jets from active galactic nuclei. In addition, the initial wind bubble shocked by the jet leads to a transient, large interaction surface. The interaction between jets and stars can produce strong inhomogeneities within the jet. As mixing is expected to be effective on large scales, even individual asymptotic giant branch stars can significantly contribute to

Cosmic Catastrophes

Science.gov (United States)

Wheeler, J. Craig

2014-08-01

Preface; 1. Setting the stage: star formation and hydrogen burning in single stars; 2. Stellar death: the inexorable grip of gravity; 3. Dancing with stars: binary stellar evolution; 4. Accretion disks: flat stars; 5. White Dwarfs: quantum dots; 6. Supernovae: stellar catastrophes; 7. Supernova 1987A: lessons and enigmas; 8. Neutron stars: atoms with attitude; 9. Black holes in theory: into the abyss; 10. Black holes in fact: exploring the reality; 11. Gamma-ray bursts, black holes and the universe: long, long ago and far, far away; 12. Supernovae and the universe; 13. Worm holes and time machines: tunnels in space and time; 14. Beyond: the frontiers; Index.

Quark jets, gluon jets and the three-gluon vertex

International Nuclear Information System (INIS)

Fodor, Z.

1989-11-01

Using hadronic jets in electron-positron annihilation, we suggest a simple and model-independent method to see the differences between quark and gluon jets. We define and analyse special energy dependent moments of jets and choose those which are the most characteristic to the jet type. The method handles the energy of a jet in an adequate way. We discuss new methods using jet flavor tagging, ordinary flavor tagging of a definite quark jet or discrimination between quark and gluon jets, to test the triple-gluon vertex in electron-positron annihilation. An enriched sample of gluon jets, jets with the smallest energy in four-jet events, as well as a continuous tagging variable are also studied. 21 refs., 6 figs. (Author)

Thermal-fluid assessment of multijet atomization for spray cooling applications

International Nuclear Information System (INIS)

Panao, Miguel R.O.; Moreira, Antonio L.N.; Durao, Diamantino F.G.

2011-01-01

Thermal management is a particularly difficult challenge to the miniaturization of electronic components because it requires high performance cooling systems capable of removing large heat loads at fast rates in order to keep the operating temperature low and controlled. To meet this challenge, the Intermittent Spray Cooling (ISC) concept has been suggested as a promising technology which uses a proper match between the frequency and duration of consecutive injection cycles to control heat transfer. This concept also depends on: the atomization strategy; a homogeneous dispersion of droplets impinging on the hot surface; and the quantitative control of the liquid deposited, avoiding excessive secondary atomization or pre-impingement-evaporation. In this work, the use of liquid atomization by multiple jets impact, also referred as multijet atomization, is the subject of a thermal-fluid assessment using heat transfer correlations previously derived for intermittent sprays. Simultaneous measurements of droplet size and velocity are provided as input for the correlations and the analysis explores the influence of the number of impinging jets on the heat removal pattern and magnitude. Emphasis is put on the promising applicability of multijet atomization for promoting an intelligent use of energy in the thermal management of electronic devices.

Concrete ensemble Kalman filters with rigorous catastrophic filter divergence.

Science.gov (United States)

Kelly, David; Majda, Andrew J; Tong, Xin T

2015-08-25

The ensemble Kalman filter and ensemble square root filters are data assimilation methods used to combine high-dimensional, nonlinear dynamical models with observed data. Ensemble methods are indispensable tools in science and engineering and have enjoyed great success in geophysical sciences, because they allow for computationally cheap low-ensemble-state approximation for extremely high-dimensional turbulent forecast models. From a theoretical perspective, the dynamical properties of these methods are poorly understood. One of the central mysteries is the numerical phenomenon known as catastrophic filter divergence, whereby ensemble-state estimates explode to machine infinity, despite the true state remaining in a bounded region. In this article we provide a breakthrough insight into the phenomenon, by introducing a simple and natural forecast model that transparently exhibits catastrophic filter divergence under all ensemble methods and a large set of initializations. For this model, catastrophic filter divergence is not an artifact of numerical instability, but rather a true dynamical property of the filter. The divergence is not only validated numerically but also proven rigorously. The model cleanly illustrates mechanisms that give rise to catastrophic divergence and confirms intuitive accounts of the phenomena given in past literature.

Oscillations in solar jets observed with the SOT of Hinode: viscous effects during reconnection

Science.gov (United States)

Tavabi, E.; Koutchmy, S.

2014-07-01

Transverse oscillatory motions and recurrence behavior in the chromospheric jets observed by Hinode/SOT are studied. A comparison is considered with the behavior that was noticed in coronal X-ray jets observed by Hinode/XRT. A jet like bundle observed at the limb in Ca II H line appears to show a magnetic topology that is similar to X-ray jets (i.e., the Eiffel tower shape). The appearance of such magnetic topology is usually assumed to be caused by magnetic reconnection near a null point. Transverse motions of the jet axis are recorded but no clear evidence of twist is appearing from the highly processed movie. The aim is to investigate the dynamical behavior of an incompressible magnetic X-point occurring during the magnetic reconnection in the jet formation region. The viscous effect is specially considered in the closed line-tied magnetic X-shape nulls. We perform the MHD numerical simulation in 2-D by solving the visco-resistive MHD equations with the tracing of velocity and magnetic field. A qualitative agreement with Hinode observations is found for the oscillatory and non-oscillatory behaviors of the observed solar jets in both the chromosphere and the corona. Our results suggest that the viscous effect contributes to the excitation of the magnetic reconnection by generating oscillations that we observed at least inside this Ca II H line cool solar jet bundle.

Fukushinobyl, the impossible catastrophe

International Nuclear Information System (INIS)

Boceno, Laurent

2012-01-01

With the emergence of variety of health and environmental crisis or catastrophes (Seveso, Bhopal, Chernobyl, AIDS, contaminated blood, mad cow, influenzas), the author proposes thoughts about the fact that it seems we are not in the era of industrial societies any longer, but in that of societies of risk. He more particularly focuses on Chernobyl and Fukushima to analyse how a social framework is built up to integrate forms of institutionalisation of multifaceted vulnerability, these institutional logics becoming latent social pathologies. In this respect, he more particularly discusses the catastrophic share of nuclear. He shows how what can be considered as a risk is socialised, dissimulated by priority, and then addresses the management of consequences of Chernobyl and how it is used to address the Japanese present situation. He notably outlines a kind of collusion between the WHO and the IAEA about nuclear issues. In his respect, he recalls a statement made by the WHO saying that, from a mental health point of view, the most satisfying solution for the future of pacific uses of nuclear energy would be the emergence of a new generation who would have learned to cope with ignorance and uncertainty

Community resilience and decision theory challenges for catastrophic events.

Science.gov (United States)

Cox, Louis Anthony

2012-11-01

Extreme and catastrophic events pose challenges for normative models of risk management decision making. They invite development of new methods and principles to complement existing normative decision and risk analysis. Because such events are rare, it is difficult to learn about them from experience. They can prompt both too little concern before the fact, and too much after. Emotionally charged and vivid outcomes promote probability neglect and distort risk perceptions. Aversion to acting on uncertain probabilities saps precautionary action; moral hazard distorts incentives to take care; imperfect learning and social adaptation (e.g., herd-following, group-think) complicate forecasting and coordination of individual behaviors and undermine prediction, preparation, and insurance of catastrophic events. Such difficulties raise substantial challenges for normative decision theories prescribing how catastrophe risks should be managed. This article summarizes challenges for catastrophic hazards with uncertain or unpredictable frequencies and severities, hard-to-envision and incompletely described decision alternatives and consequences, and individual responses that influence each other. Conceptual models and examples clarify where and why new methods are needed to complement traditional normative decision theories for individuals and groups. For example, prospective and retrospective preferences for risk management alternatives may conflict; procedures for combining individual beliefs or preferences can produce collective decisions that no one favors; and individual choices or behaviors in preparing for possible disasters may have no equilibrium. Recent ideas for building "disaster-resilient" communities can complement traditional normative decision theories, helping to meet the practical need for better ways to manage risks of extreme and catastrophic events. © 2012 Society for Risk Analysis.

Vector boson tagged jets and jet substructure

Directory of Open Access Journals (Sweden)

Vitev Ivan

2018-01-01

Full Text Available In these proceedings, we report on recent results related to vector boson-tagged jet production in heavy ion collisions and the related modification of jet substructure, such as jet shapes and jet momentum sharing distributions. Z0-tagging and γ-tagging of jets provides new opportunities to study parton shower formation and propagation in the quark-gluon plasma and has been argued to provide tight constrains on the energy loss of reconstructed jets. We present theoretical predictions for isolated photon-tagged and electroweak boson-tagged jet production in Pb+Pb collisions at √sNN = 5.02 TeV at the LHC, addressing the modification of their transverse momentum and transverse momentum imbalance distributions. Comparison to recent ATLAS and CMS experimental measurements is performed that can shed light on the medium-induced radiative corrections and energy dissipation due to collisional processes of predominantly quark-initiated jets. The modification of parton splitting functions in the QGP further implies that the substructure of jets in heavy ion collisions may differ significantly from the corresponding substructure in proton-proton collisions. Two such observables and the implication of tagging on their evaluation is also discussed.

Magnetohydrodynamic Simulations of the Formation of Molecular Clouds toward the Stellar Cluster Westerlund 2: Interaction of a Jet with a Clumpy Interstellar Medium

International Nuclear Information System (INIS)

Asahina, Yuta; Kawashima, Tomohisa; Furukawa, Naoko; Enokiya, Rei; Yamamoto, Hiroaki; Fukui, Yasuo; Matsumoto, Ryoji

2017-01-01

The formation mechanism of CO clouds observed with the NANTEN2 and Mopra telescopes toward the stellar cluster Westerlund 2 is studied by 3D magnetohydrodynamic simulations, taking into account the interstellar cooling. These molecular clouds show a peculiar shape composed of an arc-shaped cloud on one side of the TeV γ -ray source HESS J1023-575 and a linear distribution of clouds (jet clouds) on the other side. We propose that these clouds are formed by the interaction of a jet with clumps of interstellar neutral hydrogen (H i). By studying the dependence of the shape of dense cold clouds formed by shock compression and cooling on the filling factor of H i clumps, we found that the density distribution of H i clumps determines the shape of molecular clouds formed by the jet–cloud interaction: arc clouds are formed when the filling factor is large. On the other hand, when the filling factor is small, molecular clouds align with the jet. The jet propagates faster in models with small filling factors.

Magnetohydrodynamic Simulations of the Formation of Molecular Clouds toward the Stellar Cluster Westerlund 2: Interaction of a Jet with a Clumpy Interstellar Medium

Energy Technology Data Exchange (ETDEWEB)

Asahina, Yuta; Kawashima, Tomohisa [National Astronomical Observatory of Japan, Osawa, Mitaka, Tokyo 181-8588 (Japan); Furukawa, Naoko; Enokiya, Rei; Yamamoto, Hiroaki; Fukui, Yasuo [Department of Physics, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8602 (Japan); Matsumoto, Ryoji, E-mail: asahina@cfca.jp [Department of Physics, Graduate School of Science, Chiba University, 1-33 Yayoi-cho, Inage-ku, Chiba 263-8522 (Japan)

2017-02-20

The formation mechanism of CO clouds observed with the NANTEN2 and Mopra telescopes toward the stellar cluster Westerlund 2 is studied by 3D magnetohydrodynamic simulations, taking into account the interstellar cooling. These molecular clouds show a peculiar shape composed of an arc-shaped cloud on one side of the TeV γ -ray source HESS J1023-575 and a linear distribution of clouds (jet clouds) on the other side. We propose that these clouds are formed by the interaction of a jet with clumps of interstellar neutral hydrogen (H i). By studying the dependence of the shape of dense cold clouds formed by shock compression and cooling on the filling factor of H i clumps, we found that the density distribution of H i clumps determines the shape of molecular clouds formed by the jet–cloud interaction: arc clouds are formed when the filling factor is large. On the other hand, when the filling factor is small, molecular clouds align with the jet. The jet propagates faster in models with small filling factors.

18 CFR 420.44 - Cooling water.

Science.gov (United States)

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Cooling water. 420.44 Section 420.44 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS-WATER SUPPLY CHARGES Charges; Exemptions § 420.44 Cooling water. Water used...

Dynamical systems V bifurcation theory and catastrophe theory

CERN Document Server

1994-01-01

Bifurcation theory and catastrophe theory are two of the best known areas within the field of dynamical systems. Both are studies of smooth systems, focusing on properties that seem to be manifestly non-smooth. Bifurcation theory is concerned with the sudden changes that occur in a system when one or more parameters are varied. Examples of such are familiar to students of differential equations, from phase portraits. Moreover, understanding the bifurcations of the differential equations that describe real physical systems provides important information about the behavior of the systems. Catastrophe theory became quite famous during the 1970's, mostly because of the sensation caused by the usually less than rigorous applications of its principal ideas to "hot topics", such as the characterization of personalities and the difference between a "genius" and a "maniac". Catastrophe theory is accurately described as singularity theory and its (genuine) applications. The authors of this book, the first printing of w...

Effects of Cognitive-Behavioral Therapy (CBT) on Brain Connectivity Supporting Catastrophizing in Fibromyalgia.

Science.gov (United States)

Lazaridou, Asimina; Kim, Jieun; Cahalan, Christine M; Loggia, Marco L; Franceschelli, Olivia; Berna, Chantal; Schur, Peter; Napadow, Vitaly; Edwards, Robert R

2017-03-01

Fibromyalgia (FM) is a chronic, common pain disorder characterized by hyperalgesia. A key mechanism by which cognitive-behavioral therapy (CBT) fosters improvement in pain outcomes is via reductions in hyperalgesia and pain-related catastrophizing, a dysfunctional set of cognitive-emotional processes. However, the neural underpinnings of these CBT effects are unclear. Our aim was to assess CBT's effects on the brain circuitry underlying hyperalgesia in FM patients, and to explore the role of treatment-associated reduction in catastrophizing as a contributor to normalization of pain-relevant brain circuitry and clinical improvement. In total, 16 high-catastrophizing FM patients were enrolled in the study and randomized to 4 weeks of individual treatment with either CBT or a Fibromyalgia Education (control) condition. Resting state functional magnetic resonance imaging scans evaluated functional connectivity between key pain-processing brain regions at baseline and posttreatment. Clinical outcomes were assessed at baseline, posttreatment, and 6-month follow-up. Catastrophizing correlated with increased resting state functional connectivity between S1 and anterior insula. The CBT group showed larger reductions (compared with the education group) in catastrophizing at posttreatment (PCBT produced significant reductions in both pain and catastrophizing at the 6-month follow-up (PCBT group also showed reduced resting state connectivity between S1 and anterior/medial insula at posttreatment; these reductions in resting state connectivity were associated with concurrent treatment-related reductions in catastrophizing. The results add to the growing support for the clinically important associations between S1-insula connectivity, clinical pain, and catastrophizing, and suggest that CBT may, in part via reductions in catastrophizing, help to normalize pain-related brain responses in FM.

Catastrophic antiphospholipid syndrome mimicking a malignant pancreatic tumour--a case report

NARCIS (Netherlands)

van Wissen, S.; Bastiaansen, B. A. J.; Stroobants, A. K.; van den Dool, E. J.; Idu, M. M.; Levi, M. [=Marcel M.; Stroes, E. S. G.

2008-01-01

The catastrophic antiphospholipid syndrome is characterised by rapid onset thromboses, often resistant to conventional anticoagulant treatment, and resulting in life threatening multiple organ dysfunction. The diagnosis of catastrophic antiphospholipid syndrome may be difficult, predominantly due to

Development of a gas-jet-coupled multitarget system for multitracer production

International Nuclear Information System (INIS)

Haba, H.; Kaji, D.; Kanayama, Y.; Igarashi, K.; Enomoto, S.

2005-01-01

de021741792A new multitracer production system, which consists of a gas-jet-coupled multitarget system for short-lived radioactive tracers and a gas- and water-cooled target system for intense beam irradiations, has been installed on a beam line of the K540-MeV RIKEN Ring Cyclotron. The performance of the gas-jet system was investigated with 50 radionuclides of 18 elements produced in the 135 MeV nucl. -1 - 14 N induced reaction on nat Cu. The gas-jet efficiencies of the nuclides varying from 61 Cu to 24 Na, except for the chlorine isotopes, show a smooth variation as a function of the mass difference between a product and a target. The multitracers on the nat Ag and 197 Au targets were also produced by the 135 MeV nucl. -1 - 14 N beam with the intensity of 0.7 pμA, which was more than seven times the limit of the previous system. (orig.)

Tackling The Global Challenge: Humanitarian Catastrophes

Directory of Open Access Journals (Sweden)

Kenneth V. Iserson

2014-03-01

Full Text Available “Humanitarian catastrophes,” conflicts and calamities generating both widespread human suffering and destructive events, require a wide range of emergency resources. This paper answers a number of questions that humanitarian catastrophes generate: Why and how do the most-developed countries—those with the resources, capabilities, and willingness to help—intervene in specific types of disasters? What ethical and legal guidelines shape our interventions? How well do we achieve our goals? It then suggests a number of changes to improve humanitarian responses, including better NGO-government cooperation, increased research on the best disaster response methods, clarification of the criteria and roles for humanitarian (military interventions, and development of post-2015 Millennium Development Goals with more accurate progress measures. [West J Emerg Med. 2014;15(2:231–240.

Astrophysically relevant radiatively cooled hypersonic bow shocks in nested wire arrays

Science.gov (United States)

Ampleford, David

2009-11-01

We have performed laboratory experiments which introduce obstructions into hypersonic plasma flows to study the formation of shocks. Astrophysical observations have demonstrated many examples of equivalent radiatively cooled bow shocks, for example the head of protostellar jets or supernova remnants passing through the interstellar medium or between discrete clumps in jets. Wire array z-pinches allow us to study quasi-planar radiatively cooled flows in the laboratory. The early stage of a wire array z-pinch implosion consists of a steady flow of the wire material towards the axis. Given a high rate of radiative cooling, these flows reach high sonic- Mach numbers, typically up to 5. The 2D nature of this configuration allows the insertion of obstacles into the flow, such as a concentric ``inner'' wire array, as has previously been studied for ICF research. Here we study the application of such a nested array to laboratory astrophysics where the inner wires act as obstructions perpendicular to the flow, and induce bow shocks. By varying the wire array material (W/Al), the significance of radiative cooling on these shocks can be controlled, and is shown to change the shock opening angle. As multiple obstructions are present, the experiments show the interaction of multiple bow shocks. It is also possible to introduce a magnetic field around the static object, increasing the opening angle of the shocks. Further experiments can be designed to control the flow density, magnetic field structure and obstruction locations. In collaboration with: S.V. Lebedev, M.E. Cuneo, C.A. Jennings, S.N. Bland, J.P. Chittenden, A. Ciardi, G.N. Hall, S.C. Bott, M. Sherlock, A. Frank, E. Blackman

The effect of freestream turbulence on film cooling adiabatic effectiveness

International Nuclear Information System (INIS)

Mayhew, James E.; Baughn, James W.; Byerley, Aaron R.

2003-01-01

The film-cooling performance of a flat plate in the presence of low and high freestream turbulence is investigated using liquid crystal thermography. This paper contributes high-resolution color images that clearly show how the freestream turbulence spreads the cooling air around a larger area of the film-cooled surface. Distributions of the adiabatic effectiveness are determined over the film-cooled surface of the flat plate using the hue method and image processing. Three blowing rates are investigated for a model with three straight holes spaced three diameters apart, with density ratio near unity. High freestream turbulence is shown to increase the area-averaged effectiveness at high blowing rates, but decrease it at low blowing rates. At low blowing ratio, freestream turbulence clearly reduces the coverage area of the cooling air due to increased mixing with the main flow. However, at high blowing ratio, when much of the jet has lifted off in the low turbulence case, high freestream turbulence turns its increased mixing into an asset, entraining some of the coolant that penetrates into the main flow and mixing it with the air near the surface

Efficiency of an on-line isotope separator system employing cooled and NaCl-loaded He-jet methods

International Nuclear Information System (INIS)

Aeystoe, J.; Rantala, V.; Valli, K.; Hillebrand, S.; Kortelahti, M.; Eskola, K.; Raunemaa, T.

1976-01-01

A pure helium-jet at liquid nitrogen temperature coupled to a Nielsen type ion source, and a NaCl-loaded helium-jet coupled to a hollow-cathode ion source have been investigated as means to connect a cyclotron target chamber on-line to a mass separator. Technical details and performances of some critical parts of the system are described. Total separation efficiencies measured under various experimental conditions for several nuclides vary between 0.01 and 1.0%. (Auth.)

Laboratory tests of catastrophic disruption of rotating bodies

Science.gov (United States)

Morris, A. J. W.; Burchell, M. J.

2017-11-01

The results of catastrophic disruption experiments on static and rotating targets are reported. The experiments used cement spheres of diameter 10 cm as the targets. Impacts were by mm sized stainless steel spheres at speeds of between 1 and 7.75 km s-1. Energy densities (Q) in the targets ranged from 7 to 2613 J kg-1. The experiments covered both the cratering and catastrophic disruption regimes. For static, i.e. non-rotating targets the critical energy density for disruption (Q*, the value of Q when the largest surviving target fragment has a mass equal to one half of the pre-impact target mass) was Q* = 1447 ± 90 J kg-1. For rotating targets (median rotation frequency of 3.44 Hz) we found Q* = 987 ± 349 J kg-1, a reduction of 32% in the mean value. This lower value of Q* for rotating targets was also accompanied by a larger scatter on the data, hence the greater uncertainty. We suggest that in some cases the rotating targets behaved as static targets, i.e. broke up with the same catastrophic disruption threshold, but in other cases the rotation helped the break up causing a lower catastrophic disruption threshold, hence both the lower value of Q* and the larger scatter on the data. The fragment mass distributions after impact were similar in both the static and rotating target experiments with similar slopes.

Pricing Zero-Coupon Catastrophe Bonds Using EVT with Doubly Stochastic Poisson Arrivals

Directory of Open Access Journals (Sweden)

Zonggang Ma

2017-01-01

Full Text Available The frequency and severity of climate abnormal change displays an irregular upward cycle as global warming intensifies. Therefore, this paper employs a doubly stochastic Poisson process with Black Derman Toy (BDT intensity to describe the catastrophic characteristics. By using the Property Claim Services (PCS loss index data from 2001 to 2010 provided by the US Insurance Services Office (ISO, the empirical result reveals that the BDT arrival rate process is superior to the nonhomogeneous Poisson and lognormal intensity process due to its smaller RMSE, MAE, MRPE, and U and larger E and d. Secondly, to depict extreme features of catastrophic risks, this paper adopts the Peak Over Threshold (POT in extreme value theory (EVT to characterize the tail characteristics of catastrophic loss distribution. And then the loss distribution is analyzed and assessed using a quantile-quantile (QQ plot to visually check whether the PCS index observations meet the generalized Pareto distribution (GPD assumption. Furthermore, this paper derives a pricing formula for zero-coupon catastrophe bonds with a stochastic interest rate environment and aggregate losses generated by a compound doubly stochastic Poisson process under the forward measure. Finally, simulation results verify pricing model predictions and show how catastrophic risks and interest rate risk affect the prices of zero-coupon catastrophe bonds.

Financing Losses from Catastrophic Risks

Science.gov (United States)

2008-11-01

often held in the form of bonds, the interest on which is subject to corporate income tax , which reduces the net earnings to each insurer’s shareholders...course; it is a basic feature of the corporate income tax . But, as explained above, catastrophe insurance is distinguished from other types of

A numerical simulation of the piston cooling in view of consumption capabilities and enhanced power density; Numerische Simulation der Kolbenkuehlung im Hinblick auf Verbrauchspotentiale und erhoehte Leistungsdichte

Energy Technology Data Exchange (ETDEWEB)

Lutz, Johannes [BMW Group, Muenchen (Germany)

2012-11-01

To meet stringent emission regulations and high power requirements, peak cylinder pressures and specific power of petrol engines have increased dramatically in recent years. Nevertheless, regarding customer expectations and in the interest of driving dynamics, modern engines should still adhere to the established wide speed range, resulting in higher thermal loading of in-cylinder components such as piston. To ensure durability and reliability, it is vital for piston cooling concepts to keep maximum temperatures securely below an acceptable limit. In addition, reducing piston cooling at part load can help to gain efficiency and decrease fuel consumption. These exacting demands on the cooling concept require an exact analysis of thermal boundary conditions and their influence on the piston temperature. While good verified models for the combustion simulation already exist, the thermal cooling boundaries involve a greater level of uncertainty. The reason for this lies in the inadequately investigated heat transfer conditions on the piston undercrown and the running surface at present, due to complex fluid dynamics of the oil jet cooling and strong ring movements during a load cycle. This study refines the thermal boundary conditions and leads to precise knowledge of the transient and averaged heat flow through the piston and the cylinder liner. Based on these results, optimized cooling strategies to gain efficiency can be developed with the help of well validated one dimensional thermal engine models. (orig.)

Development and Test of the Cooling System for the ATLAS Hadron Tile Calorimeter

CERN Document Server

Schlager, Gerolf

2002-01-01

The ATLAS detector is a general-purpose experiment for proton-proton collisions designed to investigate the full range of physical processes at the Large Hadron Collider (LHC). The ATLAS Tile Hadron Calorimeter is designed to measure the energies of jets with a resolution of E/E = 50%/pE 3%, for j j<3. This thesis presents the detailed studies which were carried out with prototypes of the Tilecal cooling system during my year as technical student at CERN. The results will be used to validate and to determine the nal design of the cooling system of the ATLAS Tile calorimeter. The performance of the cooling unit built for the calibration of Tilecal modules was evaluated for various parameters like temperature stability and safety conditions during operation. Additionally I contributed to the analysis of the calorimeter response for di erent cooling temperatures. These results determined the constraints on the operation conditions of the cooling system in terms of temperature stability that will be needed d...

CENTIMETER CONTINUUM OBSERVATIONS OF THE NORTHERN HEAD OF THE HH 80/81/80N JET: REVISING THE ACTUAL DIMENSIONS OF A PARSEC-SCALE JET

Energy Technology Data Exchange (ETDEWEB)

Masque, Josep M.; Estalella, Robert [Departament d' Astronomia i Meteorologia, Universitat de Barcelona, Marti i Franques 1, E-08028 Barcelona, Catalunya (Spain); Girart, Josep M. [Institut de Ciencies de l' Espai, (CSIC-IEEC), Campus UAB, Facultat de Ciencies, Torre C5-parell 2, E-08193 Bellaterra, Catalunya (Spain); Rodriguez, Luis F. [Centro de Radioastronomia y Astrofisica, Universidad Nacional Autonoma de Mexico, Apartado Postal 3-72, 58090 Morelia, Michoacan (Mexico); Beltran, Maria T. [INAF-Osservatorio Astrofisico di Arcetri, Largo E. Fermi 5, I-50125 Firenze (Italy)

2012-10-10

We present 6 and 20 cm Jansky Very Large Array/Very Large Array observations of the northern head of the HH 80/81/80N jet, one of the largest collimated jet systems known so far, aimed to look for knots farther than HH 80N, the northern head of the jet. Aligned with the jet and 10' northeast of HH 80N, we found a radio source not reported before, with a negative spectral index similar to that of HH 80, HH 81, and HH 80N. The fit of a precessing jet model to the knots of the HH 80/81/80N jet, including the new source, shows that the position of this source is close to the jet path resulting from the modeling. If the new source belongs to the HH 80/81/80N jet, its derived size and dynamical age are 18.4 pc and >9 Multiplication-Sign 10{sup 3} yr, respectively. If the jet is symmetric, its southern lobe would expand beyond the cloud edge resulting in an asymmetric appearance of the jet. Based on the updated dynamical age, we speculate on the possibility that the HH 80/81/80N jet triggered the star formation observed in a dense core found ahead of HH 80N, which shows signposts of interaction with the jet. These results indicate that parsec-scale radio jets can play a role in the stability of dense clumps and the regulation of star formation in the molecular cloud.

A Self-Contained Cold Plate Utilizing Force-fed Evaporation for Cooling of High flux Electronics

Science.gov (United States)

2007-01-01

additional improvement. The second advanced heat sink to be covered was developed and studied by Sung and Mudawar [27]. They created a hybrid jet...cooling by using manifold microchannel heat sinks.” Advanced Electronic Packaging. 2 (1997) 1837-1842. [27] Sung, M. K. & Mudawar , I

Design, manufacture and performance of the JET Toroidal field coils

International Nuclear Information System (INIS)

Huguet, M.; Booth, J.; Pohlchen, R.

1983-01-01

The JET Toroidal field magnet compromises 32 D shaped coils each 5.7 m high, 3.8 wide and weighing 12 tonnes. The field produced is 3.45 Tesla at 2.9 m radius when operating at the maximum current of 66.5 kA. The coils are wound with water cooled hollow conductor and operate with an equivalent rectangular current pulse length of 20 seconds at full current. A description of the evolution of the design in relation to the constraints imposed is given first. These design constraints included the low aspect ratio of the Torus, the long pulse duration, the large mechanical forces and also the availability of suitable copper conductor sections. The stress analysis of the coil is outlined as well as the cooling requirements and some specific stresses. The construction of the D shaped coils in hard copper presents problems due to the spring back effect of the conductor. The methods adopted to solve these difficulties together with other problems related to the winding process are given. A large number of tests were carried out in order to establish the conditions necessary to obtain reliable brazed joints. During production the non destructive tests for each joint were very severe and included X-ray examination. In order to meet the JET delivery programme, a large effort has been required in terms of production tools and organization of the work at the supplier's works. This effort and the construction schedule is outlined. After assembly on the JET machine the TF coils have been tested and their initial performances in electrical, mechanical and thermal terms are compared with predicted values

Chemical formation and spectroscopy of S2 in a free jet expansion

Science.gov (United States)

Heaven, M.; Miller, Terry A.; Bondybey, V. E.

1984-01-01

H2S seeded in a free jet expansion of Ar is photolyzed by an ArF laser. The liberated free radical fragments react to form S2 molecules, cooled rotationally by the jet to ≲20 K. A detailed rotational analysis of the laser induced fluorescence spectrum of the 2-3, B-X band of S2 reveals localized perturbations due to the B″ 3Πu state of S2. A deperturbation analysis for both 32S2 and 32S34S spectra yields, in conjunction with recent work by Patino and Barrow, values for the rotational constant, spin-orbit coupling constant, and Te for B″ 3ΠuS2.

Buoyancy effects laminar slot jet impinging on a surface with constant heat flux

International Nuclear Information System (INIS)

Shokouhmand, H.; Esfahanian, V.; Masoodi, R.

2004-01-01

The two-dimensional laminar air jet issuing from a nozzle of half which terminates at height above a flat plate normal to the jet is numerically on the flow and thermal structure of the region near impingement. The impinging surface is maintained at a constant heat flux condition. The full Navier-Stocks and energy equations are solved by a finite difference method to evaluate the velocity profiles and temperature distribution. The governing parameters and their ranges are: Reynolds number Re, 10-50, Grashof number Gr, 0-50, Richardson number Ri=Gr/ Re 2 , Non dimensional nozzle height H,2-3. Results of the free streamline, local friction factor and heat transfer coefficient are graphically presented. It is found that enhancement of the heat transfer rate is substantial for high Richardson number conditions. Although the laminar jet impingement for isothermal condition has been already studied, however the constant heat flux has not been studied enough. the present paper will analyze a low velocity air jet, Which can be used for cooling of a simulated electronics package

Catastrophizing and Depressive Symptoms as Prospective Predictors of Outcomes Following Total Knee Replacement

Directory of Open Access Journals (Sweden)

Robert R Edwards

2009-01-01

Full Text Available Several recent reports suggest that pain-related catastrophizing is a risk factor for poor acute pain outcomes following surgical interventions. However, it has been less clear whether levels of catastrophizing influence longer-term postoperative outcomes. Data were analyzed from a relatively small number (n=43 of patients who underwent total knee replacement and were followed for 12 months after their surgery. Previous research has suggested that high levels of both catastrophizing and depression are associated with elevated acute postoperative pain complaints among patients undergoing knee surgery. In this sample, catastrophizing and depression at each of the assessment points were studied as prospective predictors of pain (both global pain ratings and pain at night at the subsequent assessment point over the course of one year. The predictive patterns differed somewhat across measures of pain reporting; depressive symptoms were unique predictors of greater global pain complaints, while catastrophizing was a specific and unique predictor of elevated nighttime pain. While surgical outcomes following total knee replacement are, on average, quite good, a significant minority of patients continue to experience long-term pain. The present findings suggest that high levels of catastrophizing and depression may promote enhanced pain levels, indicating that interventions designed to reduce catastrophizing and depressive symptoms may have the potential to further improve joint replacement outcomes.

Blowout jets and impulsive eruptive flares in a bald-patch topology

Science.gov (United States)

Chandra, R.; Mandrini, C. H.; Schmieder, B.; Joshi, B.; Cristiani, G. D.; Cremades, H.; Pariat, E.; Nuevo, F. A.; Srivastava, A. K.; Uddin, W.

2017-02-01

Context. A subclass of broad extreme ultraviolet (EUV) and X-ray jets, called blowout jets, have become a topic of research since they could be the link between standard collimated jets and coronal mass ejections (CMEs). Aims: Our aim is to understand the origin of a series of broad jets, some of which are accompanied by flares and associated with narrow and jet-like CMEs. Methods: We analyze observations of a series of recurrent broad jets observed in AR 10484 on 21-24 October 2003. In particular, one of them occurred simultaneously with an M2.4 flare on 23 October at 02:41 UT (SOLA2003-10-23). Both events were observed by the ARIES Hα Solar Tower-Telescope, TRACE, SOHO, and RHESSI instruments. The flare was very impulsive and followed by a narrow CME. A local force-free model of AR 10484 is the basis to compute its topology. We find bald patches (BPs) at the flare site. This BP topology is present for at least two days before to events. Large-scale field lines, associated with the BPs, represent open loops. This is confirmed by a global potential free source surface (PFSS) model. Following the brightest leading edge of the Hα and EUV jet emission, we can temporarily associate these emissions with a narrow CME. Results: Considering their characteristics, the observed broad jets appear to be of the blowout class. As the most plausible scenario, we propose that magnetic reconnection could occur at the BP separatrices forced by the destabilization of a continuously reformed flux rope underlying them. The reconnection process could bring the cool flux-rope material into the reconnected open field lines driving the series of recurrent blowout jets and accompanying CMEs. Conclusions: Based on a model of the coronal field, we compute the AR 10484 topology at the location where flaring and blowout jets occurred from 21 to 24 October 2003. This topology can consistently explain the origin of these events. The movie associated to Fig. 1 is available at http://www.aanda.org

Performance analysis of cooling stabilizing burners for different stress boiler unit

OpenAIRE

Fialko, N. M.; Prokopov, V. H.; Alyosha, S. A.; Sherenkovskyy, Y.; Meranova, N. A.; Polozenko, N. P.; Malecki, A. E.

2013-01-01

The numerical research data of the jet–stabilization burners cooling system of with different baffles are presented of the jet airflow of inside end surface by flat and round jets with different width pylon is presented. The analysis of the load influence on the boiler efficiency cooling system is carried out. Наведено дані числових досліджень систем охолодження струменево- стабілізаторних пальникових пристроїв за схемою із струменевим обдувом внутрішньої торцевої ...

The contribution of sting-jet windstorms to extreme wind risk in the North Atlantic

Science.gov (United States)

Hart, Neil C.; Gray, Suzanne L.; Clark, Peter A.

2016-04-01

Windstorms are a major winter weather risk for many countries in Europe. These storms are predominantly associated with explosively-developing extratropical cyclones that track across the region. A substantial body of literature exists on the synoptic-scale dynamics, predictability and climatology of such storms. More recently, interest in the mesoscale variability of the most damaging winds has led to a focus on the role of sting jets in enhancing windstorm severity. We present a present-era climatology of North Atlantic cyclones that had potential to produce sting jets. Considering only explosively-developing cyclones, those with sting-jet potential are more likely to have higher relative vorticity and associated low-level wind maxima. Furthermore, the strongest winds for sting-jet cyclones are more often in the cool sector, behind the cold front, when compared with other explosively-developing cyclones which commonly have strong warm-sector winds too. The tracks of sting-jet cyclones, and explosively-developing cyclones in general, show little offset from the climatological storm track. While rare over Europe, sting-jet cyclones are relatively frequent within the main storm track with up to one third of extratropical cyclones exhibiting sting-jet potential. Thus, the rarity and, until recently, lack of description of sting-jet windstorms is more due to the climatological storm track location away from highly-populated land masses, than due to an actual rarity of such storms in nature.

Configurable double-sided modular jet impingement assemblies for electronics cooling

Science.gov (United States)

Zhou, Feng; Dede, Ercan Mehmet

2018-05-22

A modular jet impingement assembly includes an inlet tube fluidly coupled to a fluid inlet, an outlet tube fluidly coupled to a fluid outlet, and a modular manifold having a first distribution recess extending into a first side of the modular manifold, a second distribution recess extending into a second side of the modular manifold, a plurality of inlet connection tubes positioned at an inlet end of the modular manifold, and a plurality of outlet connection tubes positioned at an outlet end of the modular manifold. A first manifold insert is removably positioned within the first distribution recess, a second manifold insert is removably positioned within the second distribution recess, and a first and second heat transfer plate each removably coupled to the modular manifold. The first and second heat transfer plates each comprise an impingement surface.

DeepJet: a deep-learned multiclass jet-tagger for slim and fat jets

CERN Multimedia

CERN. Geneva; Qu, Huilin; Stoye, Markus; Kieseler, Jan; Verzetti, Mauro

2018-01-01

We present a customized neural network architecture for both, slim and fat jet tagging. It is based on the idea to keep the concept of physics objects, like particle flow particles, as a core element of the network architecture. The deep learning algorithm works for most of the common jet classes, i.e. b, c, usd and gluon jets for slim jets and W, Z, H, QCD and top classes for fat jets. The developed architecture promising gains in performance as shown in simulation of the CMS collaboration. Currently the tagger is under test in real data in the CMS experiment.

The critical catastrophe revisited

International Nuclear Information System (INIS)

De Mulatier, Clélia; Rosso, Alberto; Dumonteil, Eric; Zoia, Andrea

2015-01-01

The neutron population in a prototype model of nuclear reactor can be described in terms of a collection of particles confined in a box and undergoing three key random mechanisms: diffusion, reproduction due to fissions, and death due to absorption events. When the reactor is operated at the critical point, and fissions are exactly compensated by absorptions, the whole neutron population might in principle go to extinction because of the wild fluctuations induced by births and deaths. This phenomenon, which has been named critical catastrophe, is nonetheless never observed in practice: feedback mechanisms acting on the total population, such as human intervention, have a stabilizing effect. In this work, we revisit the critical catastrophe by investigating the spatial behaviour of the fluctuations in a confined geometry. When the system is free to evolve, the neutrons may display a wild patchiness (clustering). On the contrary, imposing a population control on the total population acts also against the local fluctuations, and may thus inhibit the spatial clustering. The effectiveness of population control in quenching spatial fluctuations will be shown to depend on the competition between the mixing time of the neutrons (i.e. the average time taken for a particle to explore the finite viable space) and the extinction time

A comparison of regional and global catastrophic hazards associated with energy technologies

International Nuclear Information System (INIS)

Heising, C.D.; Inhaber, H.

1983-01-01

This paper reviews some of what is known about the relative catastrophic hazards, on both a regional and global level, of energy technologies, and proposes a logical framework for their comparison. A review of the Inhaber study results is made indicating the relative position of overall nuclear power related risks. Then, concentration is placed on describing the catastrophic and global hazards of energy technologies. Regionally catastrophic hazards include sabotage and other malicious human activities, in addition to severe accidents caused inadvertantly by man, such as fires, reactor core damage events, chemical and poisonous gas releases, fuel storage fires and explosions, in addition to others. Global risks include such hazards as nuclear proliferation, CO 2 , build-up, oil shortages and possible national conflicts over dwindling energy fuels. The conclusion is drawn that consideration of both regional and global catastrophic risks must be made in making energy decisions, and that further study is necessary to better quantify and compare these risks. A simple decision analytic framework for making energy decisions inclusive of catastrophic risk is proposed

Thermal catastrophe in the plasma sheet boundary layer

International Nuclear Information System (INIS)

Smith, R.A.; Goertz, C.K.; Grossmann, W.

1986-01-01

This letter presents a first step towards a substorm model including particle heating and transport in the plasma sheet boundary layer (PSBL). The heating mechanism discussed is resonant absorption of Alfven waves. For some assumed MHD perturbation incident from the tail lobes onto the plasma sheet, the local heating rate in the PSBL has the form of a resonance function of the one-fluid plasma temperature. Balancing the local heating by convective transport of the heated plasma toward the central plasma sheet, and ''equation of state'' is found for the steady-state PSBL whose solution has the form of a mathematical catastrophe: at a critical value of a parameter containing the incident power flux, the local density, and the convection velocity, the equilibrium temperature jumps discontinuously. Associating this temperature increase with the abrupt onset of the substorm expansion phase, the catastrophe model indicates at least three ways in which the onset may be triggered. Several other consequences related to substorm dynamics are suggested by the simple catastrophe model

Magnetic Flux Cancellation as the Origin of Solar Quiet-region Pre-jet Minifilaments

Energy Technology Data Exchange (ETDEWEB)

Panesar, Navdeep K.; Sterling, Alphonse C.; Moore, Ronald L., E-mail: navdeep.k.panesar@nasa.gov [NASA Marshall Space Flight Center, Huntsville, AL 35812 (United States)

2017-08-01

We investigate the origin of 10 solar quiet-region pre-jet minifilaments , using EUV images from the Solar Dynamics Observatory ( SDO )/Atmospheric Imaging Assembly (AIA) and magnetograms from the SDO Helioseismic and Magnetic Imager (HMI). We recently found that quiet-region coronal jets are driven by minifilament eruptions, where those eruptions result from flux cancellation at the magnetic neutral line under the minifilament. Here, we study the longer-term origin of the pre-jet minifilaments themselves. We find that they result from flux cancellation between minority-polarity and majority-polarity flux patches. In each of 10 pre-jet regions, we find that opposite-polarity patches of magnetic flux converge and cancel, with a flux reduction of 10%–40% from before to after the minifilament appears. For our 10 events, the minifilaments exist for periods ranging from 1.5 hr to 2 days before erupting to make a jet. Apparently, the flux cancellation builds a highly sheared field that runs above and traces the neutral line, and the cool transition region plasma minifilament forms in this field and is suspended in it. We infer that the convergence of the opposite-polarity patches results in reconnection in the low corona that builds a magnetic arcade enveloping the minifilament in its core, and that the continuing flux cancellation at the neutral line finally destabilizes the minifilament field so that it erupts and drives the production of a coronal jet. Thus, our observations strongly support that quiet-region magnetic flux cancellation results in both the formation of the pre-jet minifilament and its jet-driving eruption.

Experimental study of hydrogen jet ignition and jet extinguishment

International Nuclear Information System (INIS)

Wierman, R.W.

1979-04-01

Two phases are described of an experimental study that investigated: (1) the ignition characteristics of hydrogen--sodium jets, (2) the formation of hydrogen in sodium--humid air atmospheres, and (3) the extinguishment characteristics of burning hydrogen--sodium jets. Test conditions were similar to those postulated for highly-improbable breeder reactor core melt-through accidents and included: jet temperature, jet velocity, jet hydrogen concentration, jet sodium concentration, atmospheric oxygen concentration, and atmospheric water vapor concentration

Cooling tower water ozonation at Southern University

International Nuclear Information System (INIS)

Chen, C.C.; Knecht, A.T.; Trahan, D.B.; Yaghi, H.M.; Jackson, G.H.; Coppenger, G.D.

1990-01-01

Cooling-tower water is a critical utility for many industries. In the past, inexpensive water coupled with moderate regulation of discharge water led to the neglect of the cooling tower as an energy resource. Now, with the increased cost of chemical treatment and tough EPA rules and regulations, this situation is rapidly changing. The operator of the DOE Y-12 Plant in Oak Ridge as well as many other industries are forced to develop an alternate method of water treatment. The cooling tower is one of the major elements in large energy systems. The savings accrued from a well engineered cooling tower can be a significant part of the overall energy conservation plan. During a short-term ozonation study between 1987-1988, the Y-12 Plant has been successful in eliminating the need for cooling tower treatment chemicals. However, the long-term impact was not available. Since April 1988, the ozone cooling water treatment study at the Y-12 Plant has been moved to the site at Southern University in Baton Rouge, Louisiana. The purpose of this continued study is to determine whether the use of ozonation on cooling towers is practical from an economic, technical and environmental standpoint. This paper discusses system design, operating parameter and performance testing of the ozonation system at Southern University

Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

Energy Technology Data Exchange (ETDEWEB)

Debbarma, Ajoy; Pandey, Krishna Murari [National Institute of Technology, Assam (India). Dept. of Mechanical Engineering

2016-03-15

Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

International Nuclear Information System (INIS)

Debbarma, Ajoy; Pandey, Krishna Murari

2016-01-01

Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

Quark and gluon jet properties in symmetric three-jet events

Science.gov (United States)

Buskulic, D.; Casper, D.; de Bonis, I.; Decamp, D.; Ghez, P.; Goy, C.; Lees, J.-P.; Lucotte, A.; Minard, M.-N.; Odier, P.; Pietrzyk, B.; Chmeissani, M.; Crespo, J. M.; Efthymiopoulos, I.; Fernandez, E.; Fernandez-Bosman, M.; Garrido, Ll.; Juste, A.; Martinez, M.; Orteu, S.; Pacheco, A.; Padilla, C.; Palla, F.; Pascual, A.; Perlas, J. A.; Riu, I.; Sanchez, F.; Teubert, F.; Colaleo, A.; Creanza, D.; de Palma, M.; Farilla, A.; Gelao, G.; Girone, M.; Iaselli, G.; Maggi, G.; Maggi, M.; Marinelli, N.; Natali, S.; Nuzzo, S.; Ranieri, A.; Raso, G.; Romano, F.; Ruggieri, F.; Selvaggi, G.; Silvestris, L.; Tempesta, P.; Zito, G.; Huang, X.; Lin, J.; Ouyang, Q.; Wang, T.; Xie, Y.; Xu, R.; Xue, S.; Zhang, J.; Zhang, L.; Zhao, W.; Alemany, R.; Bazarko, A. O.; Bonvicini, G.; Cattaneo, M.; Comas, P.; Coyle, P.; Drevermann, H.; Forty, R. W.; Frank, M.; Hagelberg, R.; Harvey, J.; Jacobsen, R.; Janot, P.; Jost, B.; Kneringer, E.; Knobloch, J.; Lehraus, I.; Martin, E. B.; Mato, P.; Minten, A.; Miquel, R.; Mir, Ll. M.; Moneta, L.; Oest, T.; Palazzi, P.; Pater, J. R.; Pusztaszeri, J.-F.; Ranjard, F.; Rensing, P.; Rolandi, L.; Schlatter, D.; Schmelling, M.; Schneider, O.; Tejessy, W.; Tomalin, I. R.; Venturi, A.; Wachsmuth, H.; Wildish, T.; Witzeling, W.; Wotschack, J.; Ajaltouni, Z.; Barrès, A.; Boyer, C.; Falvard, A.; Gay, P.; Guicheney, C.; Henrard, P.; Jousset, J.; Michel, B.; Monteil, S.; Montret, J.-C.; Pallin, D.; Perret, P.; Podlyski, F.; Proriol, J.; Rossignol, J.-M.; Fearnley, T.; Hansen, J. B.; Hansen, J. D.; Hansen, J. R.; Hansen, P. H.; Nilsson, B. S.; Wäänänen, A.; Kyriakis, A.; Markou, C.; Simopoulou, E.; Siotis, I.; Vayaki, A.; Zachariadou, K.; Blondel, A.; Bonneaud, G.; Brient, J. C.; Bourdon, P.; Rougé, A.; Rumpf, M.; Tanaka, R.; Valassi, A.; Verderi, M.; Videau, H.; Candlin, D. J.; Parsons, M. I.; Focardi, E.; Parrini, G.; Corden, M.; Delfino, M.; Georgiopoulos, C.; Jaffe, D. E.; Antonelli, A.; Bencivenni, G.; Bologna, G.; Bossi, F.; Campana, P.; Capon, G.; Chiarella, V.; Felici, G.; Laurelli, P.; Mannocchi, G.; Murtas, F.; Murtas, G. P.; Passalacqua, L.; Pepe-Altarelli, M.; Curtis, L.; Dorris, S. J.; Halley, A. W.; Knowles, I. G.; Lynch, J. G.; O'Shea, V.; Raine, C.; Reeves, P.; Scarr, J. M.; Smith, K.; Thompson, A. S.; Thomson, F.; Thorn, S.; Turnbull, R. M.; Becker, U.; Braun, O.; Geweniger, C.; Graefe, G.; Hanke, P.; Hepp, V.; Kluge, E. E.; Putzer, A.; Rensch, B.; Schmidt, M.; Sommer, J.; Stenzel, H.; Tittel, K.; Werner, S.; Wunsch, M.; Abbaneo, D.; Beuselinck, R.; Binnie, D. M.; Cameron, W.; Colling, D. J.; Dornan, P. J.; Moutoussi, A.; Nash, J.; San Martin, G.; Sedgbeer, J. K.; Stacey, A. M.; Dissertori, G.; Girtler, P.; Kuhn, D.; Rudolph, G.; Bowdery, C. K.; Brodbeck, T. J.; Colrain, P.; Crawford, G.; Finch, A. J.; Foster, F.; Hughes, G.; Sloan, T.; Whelan, E. P.; Williams, M. I.; Galla, A.; Greene, A. M.; Kleinknecht, K.; Quast, G.; Renk, B.; Rohne, E.; Sander, H.-G.; van Gemmeren, P.; Zeitnitz, C.; Aubert, J. J.; Bencheikh, A. M.; Benchouk, C.; Bonissent, A.; Bujosa, G.; Calvet, D.; Carr, J.; Diaconu, C.; Etienne, F.; Konstantinidis, N.; Nicod, D.; Payre, P.; Rousseau, D.; Talby, M.; Sadouki, A.; Thulasidas, M.; Trabelsi, K.; Abt, I.; Assmann, R.; Bauer, C.; Blum, W.; Brown, D.; Dietl, H.; Dydak, F.; Ganis, G.; Gotzhein, C.; Jakobs, K.; Kroha, H.; Lütjens, G.; Lutz, G.; Männer, W.; Moser, H.-G.; Richter, R.; Rosado-Schlosser, A.; Schael, S.; Settles, R.; Seywerd, H.; Denis, R. St.; Wiedenmann, W.; Wolf, G.; Boucrot, J.; Callot, O.; Cordier, A.; Davier, M.; Duflot, L.; Grivaz, J.-F.; Heusse, Ph.; Jacquet, M.; Kim, D. W.; Le Diberder, F.; Lefrançois, J.; Lutz, A.-M.; Nikolic, I.; Park, H. J.; Park, I. C.; Schune, M.-H.; Simion, S.; Veillet, J.-J.; Videau, I.; Azzurri, P.; Bagliesi, G.; Batignani, G.; Bettarini, S.; Bozzi, C.; Calderini, G.; Carpinelli, M.; Ciocci, M. A.; Ciulli, V.; Dell'Orso, R.; Fantechi, R.; Ferrante, I.; Foà, L.; Forti, F.; Giassi, A.; Giorgi, M. A.; Gregorio, A.; Ligabue, F.; Lusiani, A.; Marrocchesi, P. S.; Messineo, A.; Rizzo, G.; Sanguinetti, G.; Sciabà, A.; Spagnolo, P.; Steinberger, J.; Tenchini, R.; Tonelli, G.; Vannini, C.; Verdini, P. G.; Walsh, J.; Betteridge, A. P.; Blair, G. A.; Bryant, L. M.; Cerutti, F.; Chambers, J. T.; Gao, Y.; Green, M. G.; Johnson, D. L.; Medcalf, T.; Perrodo, P.; Strong, J. A.; von Wimmersperg-Toeller, J. H.; Botterill, D. R.; Clifft, R. W.; Edgecock, T. R.; Haywood, S.; Edwards, M.; Maley, P.; Norton, P. R.; Thompson, J. C.; Bloch-Devaux, B.; Colas, P.; Emery, S.; Kozanecki, W.; Lançon, E.; Lemaire, M. C.; Locci, E.; Marx, B.; Perez, P.; Rander, J.; Renardy, J.-F.; Roussarie, A.; Schuller, J.-P.; Schwindling, J.; Trabelsi, A.; Vallage, B.; Johnson, R. P.; Kim, H. Y.; Litke, A. M.; McNeil, M. A.; Taylor, G.; Beddall, A.; Booth, C. N.; Boswell, R.; Brew, C. A. J.; Cartwright, S.; Combley, F.; Koksal, A.; Letho, M.; Newton, W. M.; Rankin, C.; Reeve, J.; Thompson, L. F.; Böhrer, A.; Brandt, S.; Cowan, G.; Feigl, E.; Grupen, C.; Lutters, G.; Minguet-Rodriguez, J.; Rivera, F.; Saraiva, P.; Smolik, L.; Stephan, F.; Apollonio, M.; Bosisio, L.; Della Marina, R.; Giannini, G.; Gobbo, B.; Musolino, G.; Ragusa, F.; Rothberg, J.; Wasserbaech, S.; Armstrong, S. R.; Bellantoni, L.; Elmer, P.; Feng, Z.; Ferguson, D. P. S.; Gao, Y. S.; González, S.; Grahl, J.; Greening, T. C.; Harton, J. L.; Hayes, O. J.; Hu, H.; McNamara, P. A.; Nachtman, J. M.; Orejudos, W.; Pan, Y. B.; Saadi, Y.; Schmitt, M.; Scott, I. J.; Sharma, V.; Turk, J. D.; Walsh, A. M.; Wu, Sau Lan; Wu, X.; Yamartino, J. M.; Zheng, M.; Zobernig, G.; Aleph Collaboration

1996-02-01

Quark and gluon jets with the same energy, 24 GeV, are compared in symmetric three-jet configurations from hadronic Z decays observed by the ALEPH detector. Jets are defined using the Durham algorithm. Gluon jets are identified using an anti-tag on b jets, based on a track impact parameter method. The comparison of gluon and mixed flavour quark jets shows that gluon jets have a softer fragmentation function, a larger angular width and a higher particle multiplicity, Evidence is presented which shows that the corresponding differences between gluon and b jets are significantly smaller. In a statistically limited comparison the multiplicity in c jets was found to be comparable with that observed for the jets of mixed quark flavour.

Two-fluid electromagnetic simulations of plasma-jet acceleration with detailed equation-of-state

International Nuclear Information System (INIS)

Thoma, C.; Welch, D. R.; Clark, R. E.; Bruner, N.; MacFarlane, J. J.; Golovkin, I. E.

2011-01-01

We describe a new particle-based two-fluid fully electromagnetic algorithm suitable for modeling high density (n i ∼ 10 17 cm -3 ) and high Mach number laboratory plasma jets. In this parameter regime, traditional particle-in-cell (PIC) techniques are challenging due to electron timescale and lengthscale constraints. In this new approach, an implicit field solve allows the use of large timesteps while an Eulerian particle remap procedure allows simulations to be run with very few particles per cell. Hall physics and charge separation effects are included self-consistently. A detailed equation of state (EOS) model is used to evolve the ion charge state and introduce non-ideal gas behavior. Electron cooling due to radiation emission is included in the model as well. We demonstrate the use of these new algorithms in 1D and 2D Cartesian simulations of railgun (parallel plate) jet accelerators using He and Ar gases. The inclusion of EOS and radiation physics reduces the electron temperature, resulting in higher calculated jet Mach numbers in the simulations. We also introduce a surface physics model for jet accelerators in which a frictional drag along the walls leads to axial spreading of the emerging jet. The simulations demonstrate that high Mach number jets can be produced by railgun accelerators for a variety of applications, including high energy density physics experiments.

Two-fluid electromagnetic simulations of plasma-jet acceleration with detailed equation-of-state

Energy Technology Data Exchange (ETDEWEB)

Thoma, C.; Welch, D. R.; Clark, R. E.; Bruner, N. [Voss Scientific, LLC, Albuquerque, New Mexico 87108 (United States); MacFarlane, J. J.; Golovkin, I. E. [Prism Computational Sciences, Inc., Madison, Wisconsin 53711 (United States)

2011-10-15

We describe a new particle-based two-fluid fully electromagnetic algorithm suitable for modeling high density (n{sub i} {approx} 10{sup 17} cm{sup -3}) and high Mach number laboratory plasma jets. In this parameter regime, traditional particle-in-cell (PIC) techniques are challenging due to electron timescale and lengthscale constraints. In this new approach, an implicit field solve allows the use of large timesteps while an Eulerian particle remap procedure allows simulations to be run with very few particles per cell. Hall physics and charge separation effects are included self-consistently. A detailed equation of state (EOS) model is used to evolve the ion charge state and introduce non-ideal gas behavior. Electron cooling due to radiation emission is included in the model as well. We demonstrate the use of these new algorithms in 1D and 2D Cartesian simulations of railgun (parallel plate) jet accelerators using He and Ar gases. The inclusion of EOS and radiation physics reduces the electron temperature, resulting in higher calculated jet Mach numbers in the simulations. We also introduce a surface physics model for jet accelerators in which a frictional drag along the walls leads to axial spreading of the emerging jet. The simulations demonstrate that high Mach number jets can be produced by railgun accelerators for a variety of applications, including high energy density physics experiments.

Stationary Population Inversion in an Expanding Argon Plasma Jet by Helium Puffing

International Nuclear Information System (INIS)

Akatsuka, H.; Kano, K.

2005-01-01

An experiment of He gas-contact for generating population inversion in a recombining Ar plasma jet is carried out. Population inversion between Ar I excited states 5s' → 4p'[1/2]1 and 5s' → 4p[3/2]1,2, [5/2]2,3 is created by helium gas-contact cooling of electrons, whereas it is not created without gas-contact. Ar I lines 1.14 μm, 1.34 μm, and 1.09 μm are strongly enhanced due to the He gas cooling. It is experimentally found that helium gas contact effectively lowers electron temperature of the Ar plasma jet. The mechanisms giving rise to population inversion are discussed in terms of atomic collisional processes of the recombining plasma. The experimental results of electron temperature and population densities are discussed by simple numerical analysis which we previously developed. It is shown that the experimental results are well explained by our modeling quantitatively for the case without gas contact, except that the agreement of number densities of lower lying non-LTE levels is qualitative for the case with the gas contact

Forecasting giant, catastrophic slope collapse: lessons from Vajont, Northern Italy

Science.gov (United States)

Kilburn, Christopher R. J.; Petley, David N.

2003-08-01

Rapid, giant landslides, or sturzstroms, are among the most powerful natural hazards on Earth. They have minimum volumes of ˜10 6-10 7 m 3 and, normally preceded by prolonged intervals of accelerating creep, are produced by catastrophic and deep-seated slope collapse (loads ˜1-10 MPa). Conventional analyses attribute rapid collapse to unusual mechanisms, such as the vaporization of ground water during sliding. Here, catastrophic collapse is related to self-accelerating rock fracture, common in crustal rocks at loads ˜1-10 MPa and readily catalysed by circulating fluids. Fracturing produces an abrupt drop in resisting stress. Measured stress drops in crustal rock account for minimum sturzstrom volumes and rapid collapse accelerations. Fracturing also provides a physical basis for quantitatively forecasting catastrophic slope failure.

A topological model for baryon production in jets

International Nuclear Information System (INIS)

Ellis, J.; Kowalski, H.

1988-01-01

We present a conceptual model for baryon production in jets, inspired by the Skyrme picture of baryons as topological defects in a chiral quark-antiquark condensate. High energy collisions produce ''hot'' partons which split perturbatively into showers of ''cool'' partons which hadronize non-perturbatively. We visualize each of these as corresponding to a connected domain with a common orientation of the chiral condensate. Topological defects, namely baryons, are formed when there are mismatches in the orientations of adjacent field domains, rather as cosmic strings or monopoles are formed in the early Universe. Our model gives a good qualitative description of various salient features of baryon production in jets, which previously could be described only with a large number of free parameters. In particular, we give a qualitative explanation of the high baryon production rate in Υ decays compared to the e + e - continuum. When combined with a perturbative QCD parton shower Monte Carlo it could become a basis for a fully-fledged fragmentation model. (orig.)

Jet substructure using semi-inclusive jet functions in SCET

International Nuclear Information System (INIS)

Kang, Zhong-Bo; Ringer, Felix; Vitev, Ivan

2016-01-01

We propose a new method to evaluate jet substructure observables in inclusive jet measurements, based upon semi-inclusive jet functions in the framework of Soft Collinear Effective Theory (SCET). As a first example, we consider the jet fragmentation function, where a hadron h is identified inside a fully reconstructed jet. We introduce a new semi-inclusive fragmenting jet function G_i"h(z=ω_J/ω,z_h=ω_h/ω_J,ω_J,R,μ), which depends on the jet radius R and the large light-cone momenta of the parton ‘i’ initiating the jet (ω), the jet (ω_J), and the hadron h (ω_h). The jet fragmentation function can then be expressed as a semi-inclusive observable, in the spirit of actual experimental measurements, rather than as an exclusive one. We demonstrate the consistency of the effective field theory treatment and standard perturbative QCD calculations of this observable at next-to-leading order (NLO). The renormalization group (RG) equation for the semi-inclusive fragmenting jet function G_i"h(z,z_h,ω_J,R,μ) are also derived and shown to follow exactly the usual timelike DGLAP evolution equations for fragmentation functions. The newly obtained RG equations can be used to perform the resummation of single logarithms of the jet radius parameter R up to next-to-leading logarithmic (NLL_R) accuracy. In combination with the fixed NLO calculation, we obtain NLO+NLL_R results for the hadron distribution inside the jet. We present numerical results for pp→(jet h)X in the new framework, and find excellent agreement with existing LHC experimental data.

Catastrophizing and perceived injustice: risk factors for the transition to chronicity after whiplash injury.

Science.gov (United States)

Sullivan, Michael J L; Adams, Heather; Martel, Marc-Olivier; Scott, Whitney; Wideman, Timothy

2011-12-01

The article will summarize research that has supported the role of pain catastrophizing and perceived injustice as risk factors for problematic recovery after whiplash injury. This article focuses on two psychological variables that have been shown to impact on recovery trajectories after whiplash injury; namely pain catastrophizing and perceived injustice. Research has shown that psychological variables play a role in determining the trajectory of recovery after whiplash injury. This article will focus on two psychological variables that have been shown to impact on recovery trajectories after whiplash injury; namely pain catastrophizing and perceived injustice. The article will summarize research that has supported the role of pain catastrophizing and perceived injustice as risk factors for problematic recovery after whiplash injury. Several investigations have shown that measures of catastrophizing and perceived injustice prospectively predict problematic trajectories of recovery after whiplash injury. Basic research points to the potential roles of expectancies, attention, coping and endogenous opioid dysregulation as possible avenues through which catastrophizing might heighten the probability of the persistence of pain after whiplash injury. Although research has yet to systematically address the mechanisms by which perceived injustice might contribute to prolonged disability in individuals with whiplash injuries, there are grounds for suggesting the potential contributions of catastrophizing, pain behavior and anger. A challenge for future research will be the development and evaluation of risk factor-targeted interventions aimed at reducing catastrophizing and perceived injustice to improve recovery trajectories after whiplash injury.

A Numerical Analysis of Heat Transfer and Effectiveness on Film Cooled Turbine Blade Tip Models

Science.gov (United States)

Ameri, A. A.; Rigby, D. L.

1999-01-01

A computational study has been performed to predict the distribution of convective heat transfer coefficient on a simulated blade tip with cooling holes. The purpose of the examination was to assess the ability of a three-dimensional Reynolds-averaged Navier-Stokes solver to predict the rate of tip heat transfer and the distribution of cooling effectiveness. To this end, the simulation of tip clearance flow with blowing of Kim and Metzger was used. The agreement of the computed effectiveness with the data was quite good. The agreement with the heat transfer coefficient was not as good but improved away from the cooling holes. Numerical flow visualization showed that the uniformity of wetting of the surface by the film cooling jet is helped by the reverse flow due to edge separation of the main flow.

Generalized laser filamentation instability coupled to cooling instability

International Nuclear Information System (INIS)

Liang, E.P.; Wong, J.; Garrison, J.

1984-01-01

We consider the propagation of laser light in an initially slightly nonuniform plasma. The classical dispersion relation for the laser filamentation growth rate (see e.g., B. Langdon, in the 1980 Lawrence Livermore National Laboratory Laser Program Annual Report, pp. 3-56, UCRL-50021-80, 1981) can be generalized to include other acoustical effects. For example, we find that the inclusion of potential imbalances in the heating and cooling rates of the ambient medium due to density and temperature perturbations can cause the laser filamentation mode to bifurcate into a cooling instability mode at long acoustic wavelengths. We also attempt to study semi-analytically the nonlinear evolution of this and related instabilities. These results have wide applications to a variety of chemical gas lasers and phenomena related to laser-target interactions (e.g., jet-like behavior)

Catastrophizing and Causal Beliefs in Whiplash

NARCIS (Netherlands)

Buitenhuis, J.; de Jong, P. J.; Jaspers, J. P. C.; Groothoff, J. W.

2008-01-01

Study Design. Prospective cohort study. Objective. This study investigates the role of pain catastrophizing and causal beliefs with regard to severity and persistence of neck complaints after motor vehicle accidents. Summary of Background Data. In previous research on low back pain, somatoform

Jets from jets: re-clustering as a tool for large radius jet reconstruction and grooming at the LHC

Energy Technology Data Exchange (ETDEWEB)

Nachman, Benjamin; Nef, Pascal; Schwartzman, Ariel; Swiatlowski, Maximilian [SLAC National Accelerator Laboratory, Stanford University,2575 Sand Hill Rd, Menlo Park, CA 94025 (United States); Wanotayaroj, Chaowaroj [Center for High Energy Physics, University of Oregon,1371 E. 13th Ave, Eugene, OR 97403 (United States)

2015-02-12

Jets with a large radius R≳1 and grooming algorithms are widely used to fully capture the decay products of boosted heavy particles at the Large Hadron Collider (LHC). Unlike most discriminating variables used in such studies, the jet radius is usually not optimized for specific physics scenarios. This is because every jet configuration must be calibrated, insitu, to account for detector response and other experimental effects. One solution to enhance the availability of large-R jet configurations used by the LHC experiments is jet re-clustering. Jet re-clustering introduces an intermediate scale rjets are calibrated and used as the inputs to reconstruct large radius jets. In this paper we systematically study and propose new jet re-clustering configurations and show that re-clustered large radius jets have essentially the same jet mass performance as large radius groomed jets. Jet re-clustering has the benefit that no additional large-R calibration is necessary, allowing the re-clustered large radius parameter to be optimized in the context of specific precision measurements or searches for new physics.

Jets from jets: re-clustering as a tool for large radius jet reconstruction and grooming at the LHC

International Nuclear Information System (INIS)

Nachman, Benjamin; Nef, Pascal; Schwartzman, Ariel; Swiatlowski, Maximilian; Wanotayaroj, Chaowaroj

2015-01-01

Jets with a large radius R≳1 and grooming algorithms are widely used to fully capture the decay products of boosted heavy particles at the Large Hadron Collider (LHC). Unlike most discriminating variables used in such studies, the jet radius is usually not optimized for specific physics scenarios. This is because every jet configuration must be calibrated, insitu, to account for detector response and other experimental effects. One solution to enhance the availability of large-R jet configurations used by the LHC experiments is jet re-clustering. Jet re-clustering introduces an intermediate scale rjets are calibrated and used as the inputs to reconstruct large radius jets. In this paper we systematically study and propose new jet re-clustering configurations and show that re-clustered large radius jets have essentially the same jet mass performance as large radius groomed jets. Jet re-clustering has the benefit that no additional large-R calibration is necessary, allowing the re-clustered large radius parameter to be optimized in the context of specific precision measurements or searches for new physics.

Nonlinear physics: Catastrophe, chaos and complexity

International Nuclear Information System (INIS)

Arecchi, F.T.

1992-01-01

Currently in the world of physics, there is open debate on the role of the three C's - catastrophe, chaos and complexity. Seen as new ideas or paradigms, incapable of being harmonized within the realm of traditional physics, these terms seem to be creating turmoil in the classical physics establishment whose foundations date back to the early seventeenth century. This paper first defines catastrophe, chaos and complexity and shows how these terms are all connected to nonlinear dynamics and how they have long since been present within scientific treatises. It also evidences the relationship of the three C's with the concept of organization, inappropriately called self-organization, and with recognition and decisional strategies of cognitive systems. Relevant to natural science, the development of these considerations is necessitating the re-examination of the role and capabilities of human knowledge and a return to inter-disciplinary scientific-philosophical debate

Communications en cas de catastrophe faisant appel aux TIC pour ...

International Development Research Centre (IDRC) Digital Library (Canada)

Communications en cas de catastrophe faisant appel aux TIC pour les collectivités vulnérables des Caraïbes. De récents événements survenus dans les Caraïbes ont mis en relief les insuffisances des mesures régionales et nationales de préparation aux catastrophes. On manque particulièrement de systèmes d'alerte ...

Spontaneous ignition in afterburner segment tests at an inlet temperature of 1240 K and a pressure of 1 atmosphere with ASTM jet-A fuel

Science.gov (United States)

Schultz, D. F.; Branstetter, J. R.

1973-01-01

A brief testing program was undertaken to determine if spontaneous ignition and stable combustion could be obtained in a jet engine afterburning operating with an inlet temperature of 1240 K and a pressure of 1 atmosphere with ASTM Jet-A fuel. Spontaneous ignition with 100-percent combustion efficiency and stable burning was obtained using water-cooled fuel spraybars as flameholders.

Jet substructure using semi-inclusive jet functions in SCET

Energy Technology Data Exchange (ETDEWEB)

Kang, Zhong-Bo [Theoretical Division, Los Alamos National Laboratory,Los Alamos, NM 87545 (United States); Department of Physics and Astronomy, University of California,Los Angeles, CA 90095 (United States); Ringer, Felix; Vitev, Ivan [Theoretical Division, Los Alamos National Laboratory,Los Alamos, NM 87545 (United States)

2016-11-25

We propose a new method to evaluate jet substructure observables in inclusive jet measurements, based upon semi-inclusive jet functions in the framework of Soft Collinear Effective Theory (SCET). As a first example, we consider the jet fragmentation function, where a hadron h is identified inside a fully reconstructed jet. We introduce a new semi-inclusive fragmenting jet function G{sub i}{sup h}(z=ω{sub J}/ω,z{sub h}=ω{sub h}/ω{sub J},ω{sub J},R,μ), which depends on the jet radius R and the large light-cone momenta of the parton ‘i’ initiating the jet (ω), the jet (ω{sub J}), and the hadron h (ω{sub h}). The jet fragmentation function can then be expressed as a semi-inclusive observable, in the spirit of actual experimental measurements, rather than as an exclusive one. We demonstrate the consistency of the effective field theory treatment and standard perturbative QCD calculations of this observable at next-to-leading order (NLO). The renormalization group (RG) equation for the semi-inclusive fragmenting jet function G{sub i}{sup h}(z,z{sub h},ω{sub J},R,μ) are also derived and shown to follow exactly the usual timelike DGLAP evolution equations for fragmentation functions. The newly obtained RG equations can be used to perform the resummation of single logarithms of the jet radius parameter R up to next-to-leading logarithmic (NLL{sub R}) accuracy. In combination with the fixed NLO calculation, we obtain NLO+NLL{sub R} results for the hadron distribution inside the jet. We present numerical results for pp→(jet h)X in the new framework, and find excellent agreement with existing LHC experimental data.

The effect of nozzle collar on signle phase and boiling heat transfer by planar impinging jet

International Nuclear Information System (INIS)

Shin, Chang Hwan; Yim, Seong Hwan; Cho, Hyung Hee; Wu, Seong Je

2005-01-01

The water jet impingement cooling is one of the techniques to remove the heat from high heat flux equipment. Local heat transfer of the confined water impinging jet and the effect of nozzle collar to enhance the heat transfer are investigated in the free surface jet and submerged jet. Boiling is initiated from the farthest downstream and increase of the wall temperature is reduced with developing boiling, forming the flat temperature distributions. The reduction in the nozzle-to-surface distance for H/W≤1 causes significant increases and distribution changes of heat transfer. Developed boiling reduces the differences of heat transfer for various conditions. The nozzle collar is employed at the nozzle exit. The distances from heated surface to nozzle collar, H c are 0.25W, 0.5W and 1.0W. The liquid film thickness is reduced and the velocity of wall jet increases as decreased spacing of collar to heated surface. Heat transfer is enhanced for region from the stagnation to x/W∼8 in the free surface jet and to x/W∼5 in the submerged jet. For nucleate boiling region of further downstream, the heat transfer by the nozzle collar is decreased in submerged jet comparing with higher velocity condition. It is because the increased velocity by collar is de-accelerated downstream

Catastrophic phase transitions and early warnings in a spatial ecological model

International Nuclear Information System (INIS)

Fernández, A; Fort, H

2009-01-01

Gradual changes in exploitation, nutrient loading, etc produce shifts between alternative stable states (ASS) in ecosystems which, quite often, are not smooth but abrupt or catastrophic. Early warnings of such catastrophic regime shifts are fundamental for designing management protocols for ecosystems. Here we study the spatial version of a popular ecological model, involving a logistically growing single species subject to exploitation, which is known to exhibit ASS. Spatial heterogeneity is introduced by a carrying capacity parameter varying from cell to cell in a regular lattice. Transport of biomass among cells is included in the form of diffusion. We investigate whether different quantities from statistical mechanics—like the variance, the two-point correlation function and the patchiness—may serve as early warnings of catastrophic phase transitions between the ASS. In particular, we find that the patch-size distribution follows a power law when the system is close to the catastrophic transition. We also provide links between spatial and temporal indicators and analyse how the interplay between diffusion and spatial heterogeneity may affect the earliness of each of the observables. We find that possible remedial procedures, which can be followed after these early signals, become more effective as the diffusion becomes lower. Finally, we comment on similarities of and differences between these catastrophic shifts and paradigmatic thermodynamic phase transitions like the liquid–vapour change of state for a fluid like water

Strategic reasoning and bargaining in catastrophic climate change games

Science.gov (United States)

Verendel, Vilhelm; Johansson, Daniel J. A.; Lindgren, Kristian

2016-03-01

Two decades of international negotiations show that agreeing on emission levels for climate change mitigation is a hard challenge. However, if early warning signals were to show an upcoming tipping point with catastrophic damage, theory and experiments suggest this could simplify collective action to reduce greenhouse gas emissions. At the actual threshold, no country would have a free-ride incentive to increase emissions over the tipping point, but it remains for countries to negotiate their emission levels to reach these agreements. We model agents bargaining for emission levels using strategic reasoning to predict emission bids by others and ask how this affects the possibility of reaching agreements that avoid catastrophic damage. It is known that policy elites often use a higher degree of strategic reasoning, and in our model this increases the risk for climate catastrophe. Moreover, some forms of higher strategic reasoning make agreements to reduce greenhouse gases unstable. We use empirically informed levels of strategic reasoning when simulating the model.

Boosted Jet Tagging with Jet-Images and Deep Neural Networks

International Nuclear Information System (INIS)

Kagan, Michael; Oliveira, Luke de; Mackey, Lester; Nachman, Benjamin; Schwartzman, Ariel

2016-01-01

Building on the jet-image based representation of high energy jets, we develop computer vision based techniques for jet tagging through the use of deep neural networks. Jet-images enabled the connection between jet substructure and tagging with the fields of computer vision and image processing. We show how applying such techniques using deep neural networks can improve the performance to identify highly boosted W bosons with respect to state-of-the-art substructure methods. In addition, we explore new ways to extract and visualize the discriminating features of different classes of jets, adding a new capability to understand the physics within jets and to design more powerful jet tagging methods

Quark and gluon jet properties in symmetric three-jet events

CERN Document Server

Buskulic, Damir; De Bonis, I; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Odier, P; Pietrzyk, B; Chmeissani, M; Crespo, J M; Efthymiopoulos, I; Fernández, E; Fernández-Bosman, M; Garrido, L; Juste, A; Martínez, M; Orteu, S; Pacheco, A; Padilla, C; Palla, Fabrizio; Pascual, A; Perlas, J A; Riu, I; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Farilla, A; Gelao, G; Girone, M; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Natali, S; Nuzzo, S; Ranieri, A; Raso, G; Romano, F; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Alemany, R; Bazarko, A O; Bonvicini, G; Cattaneo, M; Comas, P; Coyle, P; Drevermann, H; Forty, Roger W; Frank, M; Hagelberg, R; Harvey, J; Jacobsen, R; Janot, P; Jost, B; Kneringer, E; Knobloch, J; Lehraus, Ivan; Martin, E B; Mato, P; Minten, Adolf G; Miquel, R; Mir, L M; Moneta, L; Oest, T; Palazzi, P; Pater, J R; Pusztaszeri, J F; Ranjard, F; Rensing, P E; Rolandi, Luigi; Schlatter, W D; Schmelling, M; Schneider, O; Tejessy, W; Tomalin, I R; Venturi, A; Wachsmuth, H W; Wildish, T; Witzeling, W; Wotschack, J; Ajaltouni, Ziad J; Barrès, A; Boyer, C; Falvard, A; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Montret, J C; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rossignol, J M; Fearnley, Tom; Hansen, J B; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Wäänänen, A; Kyriakis, A; Markou, C; Simopoulou, Errietta; Siotis, I; Vayaki, Anna; Zachariadou, K; Blondel, A; Bonneaud, G R; Brient, J C; Bourdon, P; Rougé, A; Rumpf, M; Tanaka, R; Valassi, Andrea; Verderi, M; Videau, H L; Candlin, D J; Parsons, M I; Focardi, E; Parrini, G; Corden, M; Delfino, M C; Georgiopoulos, C H; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Passalacqua, L; Pepé-Altarelli, M; Curtis, L; Dorris, S J; Halley, A W; Knowles, I G; Lynch, J G; O'Shea, V; Raine, C; Reeves, P; Scarr, J M; Smith, K; Thompson, A S; Thomson, F; Thorn, S; Turnbull, R M; Becker, U; Braun, O; Geweniger, C; Graefe, G; Hanke, P; Hepp, V; Kluge, E E; Putzer, A; Rensch, B; Schmidt, M; Sommer, J; Stenzel, H; Tittel, K; Werner, S; Wunsch, M; Abbaneo, D; Beuselinck, R; Binnie, David M; Cameron, W; Colling, D J; Dornan, Peter J; Moutoussi, A; Nash, J; San Martin, G; Sedgbeer, J K; Stacey, A M; Dissertori, G; Girtler, P; Kuhn, D; Rudolph, G; Bowdery, C K; Brodbeck, T J; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Sloan, Terence; Whelan, E P; Williams, M I; Galla, A; Greene, A M; Kleinknecht, K; Quast, G; Renk, B; Rohne, E; Sander, H G; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Bencheikh, A M; Benchouk, C; Bonissent, A; Bujosa, G; Calvet, D; Carr, J; Diaconu, C A; Etienne, F; Konstantinidis, N P; Nicod, D; Payre, P; Rousseau, D; Talby, M; Sadouki, A; Thulasidas, M; Trabelsi, K; Abt, I; Assmann, R W; Bauer, C; Blum, Walter; Brown, D; Dietl, H; Dydak, Friedrich; Ganis, G; Gotzhein, C; Jakobs, K; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Saint-Denis, R; Wiedenmann, W; Wolf, G; Boucrot, J; Callot, O; Cordier, A; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Nikolic, I A; Park, H J; Park, I C; Schune, M H; Simion, S; Veillet, J J; Videau, I; Azzurri, P; Bagliesi, G; Batignani, G; Bettarini, S; Bozzi, C; Calderini, G; Carpinelli, M; Ciocci, M A; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Foà, L; Forti, F; Giassi, A; Giorgi, M A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Rizzo, G; Sanguinetti, G; Sciabà, A; Spagnolo, P; Steinberger, Jack; Tenchini, Roberto; Tonelli, G; Vannini, C; Verdini, P G; Walsh, J; Betteridge, A P; Blair, G A; Bryant, L M; Cerutti, F; Chambers, J T; Gao, Y; Green, M G; Johnson, D L; Medcalf, T; Perrodo, P; Strong, J A; Von Wimmersperg-Töller, J H; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Edwards, M; Maley, P; Norton, P R; Thompson, J C; Bloch-Devaux, B; Colas, P; Emery, S; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Marx, B; Pérez, P; Rander, J; Renardy, J F; Roussarie, A; Schuller, J P; Schwindling, J; Trabelsi, A; Vallage, B; Johnson, R P; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Beddall, A; Booth, C N; Boswell, R; Brew, C A J; Cartwright, S L; Combley, F; Köksal, A; Letho, M; Newton, W M; Rankin, C; Reeve, J; Thompson, L F; Böhrer, A; Brandt, S; Cowan, G D; Feigl, E; Grupen, Claus; Lutters, G; Minguet-Rodríguez, J A; Rivera, F; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Musolino, G; Ragusa, F; Rothberg, J E; Wasserbaech, S R; Armstrong, S R; Bellantoni, L; Elmer, P; Feng, Z; Ferguson, D P S; Gao, Y S; González, S; Grahl, J; Greening, T C; Harton, J L; Hayes, O J; Hu, H; McNamara, P A; Nachtman, J M; Orejudos, W; Pan, Y B; Saadi, Y; Schmitt, M; Scott, I J; Sharma, V; Turk, J; Walsh, A M; Wu Sau Lan; Wu, X; Yamartino, J M; Zheng, M; Zobernig, G

1996-01-01

Quark and gluon jets with the same energy, 24GeV, are compared in symmetric three-jet configurations from hadronic Z decays observed by the ALEPH detector. Jets are defined using the Durham algorithm. Gluon jets are identified using an anti-tag on b jets, based on either a track impact parameter method or a high transverse momentum lepton tag. The comparison of gluon and mixed flavour quark jets shows that gluon jets have a softer fragmentation function, a larger angular width and a higher particle multiplicity. Evidence is also presented which shows that the corresponding differences between gluon and heavy flavour jets are significantly smaller.

Cooling water conditioning and quality control for tokamaks

International Nuclear Information System (INIS)

Gootgeld, A.M.

1995-10-01

Designers and operators of Tokamaks and all associated water cooled, peripheral equipment, are faced with the task of providing and maintaining closed-loop, low conductivity, low impurity, cooling water systems. Most of these systems must provide large volumes of high quality cooling water at reasonable cost and comply with local and state government orders and EPA mandated national pretreatment standards and regulations. This paper discusses the DIII-D water quality requirements, the means used to obtain the necessary quality and the instrumentation used for control and monitoring. Costs to mechanically and chemically condition and maintain water quality are discussed as well as the various aspects of complying with government standards and regulations

Water cooled static pressure probe

Science.gov (United States)

Lagen, Nicholas T. (Inventor); Eves, John W. (Inventor); Reece, Garland D. (Inventor); Geissinger, Steve L. (Inventor)

1991-01-01

An improved static pressure probe containing a water cooling mechanism is disclosed. This probe has a hollow interior containing a central coolant tube and multiple individual pressure measurement tubes connected to holes placed on the exterior. Coolant from the central tube symmetrically immerses the interior of the probe, allowing it to sustain high temperature (in the region of 2500 F) supersonic jet flow indefinitely, while still recording accurate pressure data. The coolant exits the probe body by way of a reservoir attached to the aft of the probe. The pressure measurement tubes are joined to a single, larger manifold in the reservoir. This manifold is attached to a pressure transducer that records the average static pressure.

Madame Bovary and Catastrophism: Revolving narratives

Directory of Open Access Journals (Sweden)

Ruth Morris

2011-07-01

Full Text Available Cet article relie Madame Bovary au contexte scientifique français des années 1850, en lisant le roman de Flaubert à la lumière des théories de Cuvier. Le savant français Georges Cuvier, avec nombre de ses contemporains, explique les origines du monde à l’aide de la théorie des catastrophes. D’après cette théorie, le monde est divisé en périodes très courtes ponctuées de grandes catastrophes ou, en termes cuviériens, de « révolutions » qui ont éradiqué toute vie et ont permis au monde d’être entièrement repeuplé. Une telle conception affecte l’idée même du « temps ». Cuvier pense que la formation de la Terre est relativement récente, l’époque présente n’étant vieille que de cinq mille ans. Cette compression temporelle peut être rapportée à Madame Bovary dont le « tempo » s’accroît au fur et à mesure qu’on se rapproche du dénouement. Dans la théorie des catastrophes comme dans le roman, le temps ne suit pas une ligne chronologique. Les « révolutions » viennent briser le fil continu du temps et Emma est souvent incapable de distinguer entre le passé, le présent et le futur. Les « révolutions » servent aussi à ponctuer et à perturber le cours de la vie sur Terre en produisant des événements majeurs dans l’histoire du globe. Il en est de même dans la vie d’Emma. Son existence est marquée par des événements majeurs, comme le bal, qui créent un éclatement et une fragmentation de la temporalité, comme dans la théorie de Cuvier. Je défendrai aussi l’idée d’un lien entre la soudaineté et la violence des « révolutions » et les crises nerveuses d’Emma, qui surviennent brusquement et relèvent de l’hystérie. La conception cuviérienne de la temporalité doit enfin être envisagée au regard des théories de l’évolution, ce qui implique de réévaluer les notions d’adaptation, d’hérédité et de mort dans le roman de Flaubert.This paper locates Madame

Apparatus for production of ultrapure amorphous metals utilizing acoustic cooling

Science.gov (United States)

Lee, M. C. (Inventor)

1985-01-01

Amorphous metals are produced by forming a molten unit of metal and deploying the unit into a bidirectional acoustical levitating field or by dropping the unit through a spheroidizing zone, a slow quenching zone, and a fast quenching zone in which the sphere is rapidly cooled by a bidirectional jet stream created in the standing acoustic wave field produced between a half cylindrical acoustic driver and a focal reflector or a curved driver and a reflector. The cooling rate can be further augmented first by a cryogenic liquid collar and secondly by a cryogenic liquid jacket surrounding a drop tower. The molten unit is quenched to an amorphous solid which can survive impact in a unit collector or is retrieved by a vacuum chuck.

Catastrophic event modeling. [lithium thionyl chloride batteries

Science.gov (United States)

Frank, H. A.

1981-01-01

A mathematical model for the catastrophic failures (venting or explosion of the cell) in lithium thionyl chloride batteries is presented. The phenomenology of the various processes leading to cell failure is reviewed.

High resolution spectroscopy of jet cooled phenyl radical: The ν{sub 1} and ν{sub 2} a{sub 1} symmetry C–H stretching modes

Energy Technology Data Exchange (ETDEWEB)

Chang, Chih-Hsuan; Nesbitt, David J. [JILA, National Institute of Standards and Technology, University of Colorado, Boulder, Colorado 80309, USA and Department of Chemistry and Biochemistry, University of Colorado, Boulder, Colorado 80309 (United States)

2016-07-28

A series of CH stretch modes in phenyl radical (C{sub 6}H{sub 5}) has been investigated via high resolution infrared spectroscopy at sub-Doppler resolution (∼60 MHz) in a supersonic discharge slit jet expansion. Two fundamental vibrations of a{sub 1} symmetry, ν{sub 1} and ν{sub 2}, are observed and rotationally analyzed for the first time, corresponding to in-phase and out-of-phase symmetric CH stretch excitation at the ortho/meta/para and ortho/para C atoms with respect to the radical center. The ν{sub 1} and ν{sub 2} band origins are determined to be 3073.968 50(8) cm{sup −1} and 3062.264 80(7) cm{sup −1}, respectively, which both agree within 5 cm{sup −1} with theoretical anharmonic scaling predictions based on density functional B3LYP/6-311g++(3df,3dp) calculations. Integrated band strengths for each of the CH stretch bands are analyzed, with the relative intensities agreeing remarkably well with theoretical predictions. Frequency comparison with previous low resolution Ar-matrix spectroscopy [A. V. Friderichsen et al., J. Am. Chem. Soc. 123, 1977 (2001)] reveals a nearly uniform Δν ≈ + 10-12 cm{sup −1} blue shift between gas phase and Ar matrix values for ν{sub 1} and ν{sub 2}. This differs substantially from the much smaller red shift (Δν ≈ − 1 cm{sup −1}) reported for the ν{sub 19} mode, and suggests a simple physical model in terms of vibrational mode symmetry and crowding due to the matrix environment. Finally, the infrared phenyl spectra are well described by a simple asymmetric rigid rotor Hamiltonian and show no evidence for spectral congestion due to intramolecular vibrational coupling, which bodes well for high resolution studies of other ring radicals and polycyclic aromatic hydrocarbons. In summary, the combination of slit jet discharge methods with high resolution infrared lasers enables spectroscopic investigation of even highly reactive combustion and interstellar radical intermediates under gas phase, jet-cooled

Thermoelectric Cooling-Aided Bead Geometry Regulation in Wire and Arc-Based Additive Manufacturing of Thin-Walled Structures

Directory of Open Access Journals (Sweden)

Fang Li

2018-01-01

Full Text Available Wire and arc-based additive manufacturing (WAAM is a rapidly developing technology which employs a welding arc to melt metal wire for additive manufacturing purposes. During WAAM of thin-walled structures, as the wall height increases, the heat dissipation to the substrate is slowed down gradually and so is the solidification of the molten pool, leading to variation of the bead geometry. Though gradually reducing the heat input via adjusting the process parameters can alleviate this issue, as suggested by previous studies, it relies on experience to a large extent and inevitably sacrifices the deposition rate because the wire feed rate is directly coupled with the heat input. This study introduces for the first time an in-process active cooling system based on thermoelectric cooling technology into WAAM, which aims to eliminate the difference in heat dissipation between upper and lower layers. The case study shows that, with the aid of thermoelectric cooling, the bead width error is reduced by 56.8%, the total fabrication time is reduced by 60.9%, and the average grain size is refined by 25%. The proposed technique provides new insight into bead geometry regulation during WAAM with various benefits in terms of geometric accuracy, productivity, and microstructure.

Jet-images: computer vision inspired techniques for jet tagging

Energy Technology Data Exchange (ETDEWEB)

Cogan, Josh; Kagan, Michael; Strauss, Emanuel; Schwarztman, Ariel [SLAC National Accelerator Laboratory,Menlo Park, CA 94028 (United States)

2015-02-18

We introduce a novel approach to jet tagging and classification through the use of techniques inspired by computer vision. Drawing parallels to the problem of facial recognition in images, we define a jet-image using calorimeter towers as the elements of the image and establish jet-image preprocessing methods. For the jet-image processing step, we develop a discriminant for classifying the jet-images derived using Fisher discriminant analysis. The effectiveness of the technique is shown within the context of identifying boosted hadronic W boson decays with respect to a background of quark- and gluon-initiated jets. Using Monte Carlo simulation, we demonstrate that the performance of this technique introduces additional discriminating power over other substructure approaches, and gives significant insight into the internal structure of jets.

Jet-images: computer vision inspired techniques for jet tagging

International Nuclear Information System (INIS)

Cogan, Josh; Kagan, Michael; Strauss, Emanuel; Schwarztman, Ariel

2015-01-01

We introduce a novel approach to jet tagging and classification through the use of techniques inspired by computer vision. Drawing parallels to the problem of facial recognition in images, we define a jet-image using calorimeter towers as the elements of the image and establish jet-image preprocessing methods. For the jet-image processing step, we develop a discriminant for classifying the jet-images derived using Fisher discriminant analysis. The effectiveness of the technique is shown within the context of identifying boosted hadronic W boson decays with respect to a background of quark- and gluon-initiated jets. Using Monte Carlo simulation, we demonstrate that the performance of this technique introduces additional discriminating power over other substructure approaches, and gives significant insight into the internal structure of jets.

Catastrophic antiphospholipid syndrome and pregnancy. Clinical report.

Science.gov (United States)

Khizroeva, J; Bitsadze, V; Makatsariya, A

2018-01-08

We have observed the development of a catastrophic antiphospholipid syndrome (CAPS) in a pregnant woman hospitalized at 28 weeks of gestation with a severe preeclampsia. On the same day, an eclampsia attack developed, and an emergency surgical delivery was performed. On the third day, multiorgan failure developed. Examination showed a persistent circulation of lupus anticoagulant, high level of antibodies to cardiolipin, b2-glycoprotein I, and prothrombin. The usual diagnosis of the severe preeclampsia masked a catastrophic antiphospholipid syndrome, exacerbated by the coincident presence of several types of antiphospholipid antibodies. The first pregnancy resulted in a premature birth at 25 weeks, possibly also due to the circulation of antiphospholipid antibodies. The trigger of the catastrophic form development was the pregnancy itself, surgical intervention, and hyperhomocysteinemia. CAPS is the most severe form of antiphospholipid syndrome, manifested in multiple microthrombosis of microcirculation of vital organs and in the development of multiorgan failure against the background of the high level of antiphospholipid antibodies. CAPS is characterized by renal, cerebral, gastrointestinal, adrenal, ovarian, skin, and other forms of microthrombosis. Thrombosis recurrence is typical. Thrombotic microvasculopathy lies at the heart of multiorgan failure and manifests clinically in central nervous system lesions, adrenal insufficiency, and ARDS development. CAPS is a life-threatening condition, therefore, requires an urgent treatment. Optimal treatment of CAPS is not developed. CAPS represent a general medical multidisciplinary problem.

Natural gas cooling: Part of the solution

International Nuclear Information System (INIS)

Jones, D.R.

1992-01-01

This paper reviews and compares the efficiencies and performance of a number of gas cooling systems with a comparable electric cooling system. The results show that gas cooling systems compare favorably with the electric equivalents, offering a new dimension to air conditioning and refrigeration systems. The paper goes on to compare the air quality benefits of natural gas to coal or oil-burning fuel systems which are used to generate the electricity for the electric cooling systems. Finally, the paper discusses the regulatory bias that the author feels exists towards the use of natural gas and the need for modification in the existing regulations to provide a 'level-playing field' for the gas cooling industry

Catastrophic subsidence: An environmental hazard, shelby county, Alabama

Science.gov (United States)

Lamoreaux, Philip E.; Newton, J. G.

1986-03-01

Induced sinkholes (catastrophic subsidence) are those caused or accelerated by human activities These sinkholes commonly result from a water level decline due to pumpage Construction activities in a cone of depression greatly increases the likelihood of sinkhole occurrence Almost all occur where cavities develop in unconsolidated deposits overlying solution openings in carbonate rocks. Triggering mechanisms resulting from water level declines are (1) loss of buoyant support of the water, (2) increased gradient and water velocity, (3) water-level fluctuations, and (4) induced recharge Construction activities triggering sinkhole development include ditching, removing overburden, drilling, movement of heavy equipment, blasting and the diversion and impoundment of drainage Triggering mechanisms include piping, saturation, and loading Induced sinkholes resulting from human water development/management activities are most predictable in a youthful karst area impacted by groundwater withdrawals Shape, depth, and timing of catastrophic subsidence can be predicted in general terms Remote sensing techniques are used in prediction of locations of catastrophic subsidence. This provides a basis for design and relocation of structures such as a gas pipeline, dam, or building Utilization of techniques and a case history of the relocation of a pipeline are described

The influence of the stagnation zone on the fluid dynamics at the nozzle exit of a confined and submerged impinging jet

Science.gov (United States)

Jeffers, Nicholas; Stafford, Jason; Conway, Ciaran; Punch, Jeff; Walsh, Edmond

2016-02-01

Low profile impinging jets provide a means to achieve high heat transfer coefficients while occupying a small quantity of space. Consequently, they are found in many engineering applications such as electronics cooling, annealing of metals, food processing, and others. This paper investigates the influence of the stagnation zone fluid dynamics on the nozzle exit flow condition of a low profile, submerged, and confined impinging water jet. The jet was geometrically constrained to a round, 16-mm diameter, square-edged nozzle at a jet exit to target surface spacing ( H/ D) that varied between 0.25 choice of inlet boundary conditions in numerical models, and it was found that it is necessary to model a jet tube length {{ L}{/}{ D}} > 0.5—where D is the inner diameter of the jet—in order to minimise modelling uncertainty.

Catastrophic antiphospholipid syndrome in leprosy | Chewoolkar ...

African Journals Online (AJOL)

Catastrophic antiphospholipid syndrome is an acute and life threatening variant of antiphospholipid syndrome with a high mortality rate. Many infections are known to be accompanied by the thrombotic manifestations of this syndrome. We came across a patient of leprosy who developed bowel ischaemia secondary to ...

Computational Study of Film Cooling Effectiveness for a Comparison of Cylindrical, Square and Triangular Holes of Equal Cross-Sectional Area

Directory of Open Access Journals (Sweden)

Fayyaz Hassan Asghar

2010-10-01

Full Text Available Film cooling effectiveness is studied computationally for a comparison of circular, square and two types of equilateral triangular holes with an inclination of 30o with streamwise direction. Reynolds number based on the freestream velocity and hole diameter is 10364. Length to diameter ratio of circular hole is 4, which is representative of gas turbine engines. The coolant to mainstream density ratio is 0.92. Main flow is supplied at the temperature of 293.15K and coolant is supplied at 318.15K. Centerline and laterally averaged effectiveness are presented for film cooling measurements. Current computational results for circular hole are compared with experimental results. Computational results are well in agreement with the experimental results even for high blowing ratios. Blowing ratios ranging from 0.33-2.0 have been investigated. It is observed that triangular hole having lateral straight edge on leeward side shows much higher effectiveness values than circular film cooling hole case in the near hole region and almost similar coolant jet height as that in case of circular film cooling. Also it is observed that triangular hole having lateral straight edge on windward side and converging corner on leeward side shows lesser coolant jet height and higher film cooling effectiveness in the region x/D>10, especially at blowing ratios greater than 1.0.

Effect of hole imperfection on adiabatic film cooling effectiveness

International Nuclear Information System (INIS)

Jovanovic, M.B.; Lange, H.C.; Steenhoven, A.A. van

2008-01-01

The influence of a discrete imperfection on film cooling is studied by means of thermochromic liquid crystals measurements of the adiabatic film cooling effectiveness. As a benchmark, the effect of a jet ejected through a perfect hole is used. The film cooling effectiveness achieved with an imperfect hole is compared to the benchmark. A half torus plays the role of the discrete imperfection. The influence of the presence of the imperfection, its position and the turbulence intensity of the free stream are analyzed. The measurement data are depicted as two-dimensional plots but also as integral values. It is found that the imperfection, placed one diameter from the hole leading edge, deteriorates the effectiveness at moderate velocity ratios. Under the same conditions, the same imperfection fixed at the hole exit improves the effectiveness. At the velocity ratio of 1.50, the exit imperfection improves the integral effectiveness relatively for more than two times. The turbulence intensity and imperfections placed deeper in the hole do not have a significant influence

Flat plate film cooling at the coolant supply into triangular and cylindrical craters

Directory of Open Access Journals (Sweden)

Khalatov Artem A.

2017-01-01

Full Text Available The results are given of the film cooling numerical simulation of three different schemes including single-array of the traditional round inclined holes, as well as inclined holes arranged in the cylindrical or triangular dimples (craters. The results of simulation showed that at the medium and high values of the blowing ratio (m > 1.0 the scheme with coolant supply into triangular craters improves the adiabatic film cooling efficiency by 1.5…2.7 times compared to the traditional array of inclined holes, or by 1.3…1.8 times compared to the scheme with coolant supply into cylindrical craters. The greater film cooling efficiency with the coolant supply into triangular craters is explained by decrease in the intensity of secondary vortex structures (“kidney” vortex. This is due to the partial destruction and transformation of the coolant jets structure interacting with front wall of the crater. Simultaneously, the film cooling uniformity is increased in the span-wise direction.

Development of blow down and sodium-water reaction jet analysis codes-Validation by sodium-water reaction tests (SWAT-1R)

International Nuclear Information System (INIS)

Hiroshi Seino; Akikazu Kurihara; Isao Ono; Koji Jitsu

2005-01-01

Blow down analysis code (LEAP-BLOW) and sodium-water reaction jet analysis code (LEAP-JET) have been developed in order to improve the evaluation method on sodium-water reaction event in the steam generator (SG) of a sodium cooled fast breeder reactor (FBR). The validation analyses by these two codes were carried out using the data of Sodium-Water Reaction Test (SWAT-1R). The following main results have been obtained through this validation: (1) The calculational results by LEAP-BLOW such as internal pressure and water flow rate show good agreement with the results of the SWAT- 1R test. (2) The LEAP-JET code can qualitatively simulate the behavior of sodium-water reaction. However, it is found that the code has tendency to overestimate the maximum temperature of the reaction jet. (authors)

Complex astrophysical experiments relating to jets, solar loops, and water ice dusty plasma

Science.gov (United States)

Bellan, P. M.; Zhai, X.; Chai, K. B.; Ha, B. N.

2015-10-01

> Recent results of three astrophysically relevant experiments at Caltech are summarized. In the first experiment magnetohydrodynamically driven plasma jets simulate astrophysical jets that undergo a kink instability. Lateral acceleration of the kinking jet spawns a Rayleigh-Taylor instability, which in turn spawns a magnetic reconnection. Particle heating and a burst of waves are observed in association with the reconnection. The second experiment uses a slightly different setup to produce an expanding arched plasma loop which is similar to a solar corona loop. It is shown that the plasma in this loop results from jets originating from the electrodes. The possibility of a transition from slow to fast expansion as a result of the expanding loop breaking free of an externally imposed strapping magnetic field is investigated. The third and completely different experiment creates a weakly ionized plasma with liquid nitrogen cooled electrodes. Water vapour injected into this plasma forms water ice grains that in general are ellipsoidal and not spheroidal. The water ice grains can become quite long (up to several hundred microns) and self-organize so that they are evenly spaced and vertically aligned.

Heavy water jet target and a beryllium target for production of fast neutrons

International Nuclear Information System (INIS)

Logan, C.M.; Anderson, J.D.; Barschall, H.H.; Davis, J.C.

1975-01-01

A limitation on the neutron flux obtainable from proton or deuteron induced reactions is the heating of the target by the accelerated charged particles. The heat can be removed more easily if the target moves. The possibility of using a rotating Be target and a heavy water jet as a target for bombardment by 35-MeV deuterons was studied. In a thick Be metal target moving at 10 m/sec through such a beam of 1 cm diameter a temperature pulse of about 300 0 C will be produced by the 0.3 MW beam. The Be target should be able to withstand such a temperature pulse. A Be target suitable for 3 MW of power in a 1 cm diameter beam would require internal cooling and a higher velocity. A free jet of heavy water is also a possible target. Laser photographs of water jets in vacuum show small angles of divergence. The effect of heating by a 0.3 MW beam is probably not important because the temperature rise produced by the beam is small compared to the absolute temperature of the unheated jet. (auth)

Polarization catastrophe in nanostructures doped in photonic band gap materials

Energy Technology Data Exchange (ETDEWEB)

Singh, Mahi R. [Department of Physics and Astronomy, University of Western Ontario, London N6A 3K7 (Canada)], E-mail: msingh@uwo.ca

2008-11-30

In the presence of the dipole-dipole interaction, we have studied a possible dielectric catastrophe in photonic band gap materials doped with an ensemble of four-level nanoparticles. It is found that the dielectric constant of the system has a singularity when the resonance energy lies within the bands. This phenomenon is known as the dielectric catastrophe. It is also found that this phenomenon depends on the strength of the dipole-dipole interaction.

Catastrophic Health Expenditure and Household Impoverishment: a case of NCDs prevalence in Kenya

Directory of Open Access Journals (Sweden)

Daniel Mwai

2016-03-01

Full Text Available Introduction and problem: Non-Communicable Diseases (NCDs have become one of the leading causes of morbidity and mortality in Kenya. Their claim on financial and time resources adversely affects household welfare. Health care cost for NCDs in Kenya is predominantly paid by households as OOP. Health expenditure on NCD stands at 6.2% of Total Health Expenditure which is 0.4 % of the total gross domestic product of the country. This expenditure scenario could have implications on household welfare through catastrophic expenditure in Kenya. Most studies done on catastrophic expenditure in Kenya have not looked at the effect of NCD on poverty. Methodology: The paper has investigated the determinants of catastrophic health spending in a household with special focus on the NCDs. It has also investigated the effect of catastrophic expenditure on household welfare.A National household level survey data on expenditure and utilization is used. Controlling for endogeneity, the results revealed that NCDs and communicable diseases contribute significantly to the likelihood of a household incurring catastrophic expenditure. Results: Although all types of sicknesses have negative effects on household welfare, NCDs have more severe impacts on impoverishment. Policy wise, government and development partners should put in place a health financing plan entailing health insurance and resource pooling as a mean towards social protection. Key words:  Non-Communicable Diseases (NCD, Catastrophic Health Expenditure, endogeneity Impoverishment

Helium release rates and ODH calculations from RHIC magnet cooling line failure

Energy Technology Data Exchange (ETDEWEB)

Liaw, C.J.; Than, Y.; Tuozzolo, J.

2011-03-28

A catastrophic failure of the magnet cooling lines, similar to the LHC superconducting bus failure incident, could discharge cold helium into the RHIC tunnel and cause an Oxygen Deficiency Hazard (ODH) problem. A SINDA/FLUINT{reg_sign} model, which simulated the 4.5K/4 atm helium flowing through the magnet cooling system distribution lines, then through a line break into the insulating vacuum volumes and discharging via the reliefs into the RHIC tunnel, had been developed. Arc flash energy deposition and heat load from the ambient temperature cryostat surfaces are included in the simulations. Three typical areas: the sextant arc, the Triplet/DX/D0 magnets, and the injection area, had been analyzed. Results, including helium discharge rates, helium inventory loss, and the resulting oxygen concentration in the RHIC tunnel area, are reported. Good agreement had been achieved when comparing the simulation results, a RHIC sector depressurization test measurement, and some simple analytical calculations.

Cognitive Impairments in Fibromyalgia Syndrome: Associations With Positive and Negative Affect, Alexithymia, Pain Catastrophizing and Self-Esteem.

Science.gov (United States)

Galvez-Sánchez, Carmen M; Reyes Del Paso, Gustavo A; Duschek, Stefan

2018-01-01

Fibromyalgia syndrome (FMS) is a chronic condition characterized by widespread pain accompanied by symptoms like depression, anxiety, sleep disturbance and fatigue. In addition, affected patients frequently report cognitive disruption such as forgetfulness, concentration difficulties or mental slowness. Though cognitive deficits in FMS have been confirmed in various studies, not much is known about the mechanisms involved in their origin. This study aimed to investigate the contribution of affect-related variables to cognitive impairments in FMS. For this purpose, 67 female FMS patients and 32 healthy control subjects completed a battery of cognitive tests measuring processing speed, attention, visuospatial and verbal memory, cognitive flexibility and planning abilities. In addition, participants completed self-report questionnaires pertaining to positive and negative affect, alexithymia, pain catastrophizing and self-esteem. Clinical characteristics including pain severity, symptoms of depression and anxiety, insomnia and fatigue were also assessed. FMS patients showed markedly poorer performance than healthy controls in all of the cognitive domains assessed, in addition to greater levels of depression, anxiety, negative affect, alexithymia and pain catastrophizing, and lower self-esteem and positive affect. In exploratory correlation analysis in the FMS sample, lower cognitive performance was associated with higher pain severity, depression, anxiety, negative affect, alexithymia and pain catastrophizing, as well as lower self-esteem and positive affect. However, in regression analyses, pain, self-esteem, alexithymia, and pain catastrophizing explained the largest portion of the variance in performance. While interference effects of clinical pain in cognition have been previously described, the present findings suggest that affective factors also substantially contribute to the genesis of cognitive impairments. They support the notion that affective disturbances

Numerical investigation of mist/air impingement cooling on ribbed blade leading-edge surface.

Science.gov (United States)

Bian, Qingfei; Wang, Jin; Chen, Yi-Tung; Wang, Qiuwang; Zeng, Min

2017-12-01

The working gas turbine blades are exposed to the environment of high temperature, especially in the leading-edge region. The mist/air two-phase impingement cooling has been adopted to enhance the heat transfer on blade surfaces and investigate the leading-edge cooling effectiveness. An Euler-Lagrange particle tracking method is used to simulate the two-phase impingement cooling on the blade leading-edge. The mesh dependency test has been carried out and the numerical method is validated based on the available experimental data of mist/air cooling with jet impingement on a concave surface. The cooling effectiveness on three target surfaces is investigated, including the smooth and the ribbed surface with convex/concave columnar ribs. The results show that the cooling effectiveness of the mist/air two-phase flow is better than that of the single-phase flow. When the ribbed surfaces are used, the heat transfer enhancement is significant, the surface cooling effectiveness becomes higher and the convex ribbed surface presents a better performance. With the enhancement of the surface heat transfer, the pressure drop in the impingement zone increases, but the incremental factor of the flow friction is smaller than that of the heat transfer enhancement. Copyright © 2017 Elsevier Ltd. All rights reserved.

Excimer-mediated photoionization of covalently-linked diaryl compounds: Energy thresholds for excimer formation and excimer-assisted photoionization of jet-cooled bis (9-Fluorenyl) methane

International Nuclear Information System (INIS)

Lee, Jae Kwang; Kang, Heun Kag; Cho, Han Joung; Boo, Bong Hyun; Lim, Edward C.

2001-01-01

Diarylakanes capable of adopting a face-to face arrangement of the two aromatic rings are ideal systems in which to probe the excited-state dynamics leading to excimer formation and the role of the singlet excimer in the photoionization of covalently linked bichromophoric molecules. Bis (9-eluorenyl) methane, BFM, is a good example of such diaryl compounds. Boo and co-workers have shown that BFM exhibits excrimer fluorescence in solution at ambient temperatures. An Arrhenius plot of the temperature-dependent excimer formation rate yielded activation energy of about 15 kJ·mol -1 . It has been proposed that the activation energy is related to the barrier for transforming the initial S 1 geometry to the face-to face (sandwich-pair) geometry of the intramolecular singlet excimer. This is accord with the study of an intramolecular excimer formation in jet-cooled 1, 3-diphenylpropane (DPP), and that of an intramolecular exciplex formation in 1-(9-anthryl)-3-(4-N, N-dimethylaniline) propane, which indicate that the energy threshold for such conformational changes is about 11 kJ·mol -1 .

Experimental and theoretical investigations of mechanisms responsible for plasma jets formation at PALS

Czech Academy of Sciences Publication Activity Database

Kasperczuk, A.; Pisarczyk, T.; Demchenko, N. N.; Gus'kov, S. Yu.; Kálal, M.; Ullschmied, Jiří; Krouský, Eduard; Mašek, Karel; Pfeifer, Miroslav; Rohlena, Karel; Skála, Jiří; Pisarczyk, P.

2009-01-01

Roč. 27, č. 3 (2009), s. 415-427 ISSN 0263-0346 R&D Projects: GA MŠk(CZ) LC528 Institutional research plan: CEZ:AV0Z20430508; CEZ:AV0Z10100523 Keywords : Laser-plasma interaction * laser produced-plasma jet * radiative cooling * target irradiation geometry * PALS laser * laser interferometry Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 4.420, year: 2008

Optimal design of earth-moving machine elements with cusp catastrophe theory application

Science.gov (United States)

Pitukhin, A. V.; Skobtsov, I. G.

2017-10-01

This paper deals with the optimal design problem solution for the operator of an earth-moving machine with a roll-over protective structure (ROPS) in terms of the catastrophe theory. A brief description of the catastrophe theory is presented, the cusp catastrophe is considered, control parameters are viewed as Gaussian stochastic quantities in the first part of the paper. The statement of optimal design problem is given in the second part of the paper. It includes the choice of the objective function and independent design variables, establishment of system limits. The objective function is determined as mean total cost that includes initial cost and cost of failure according to the cusp catastrophe probability. Algorithm of random search method with an interval reduction subject to side and functional constraints is given in the last part of the paper. The way of optimal design problem solution can be applied to choose rational ROPS parameters, which will increase safety and reduce production and exploitation expenses.

The Winter Cooling Trend in Eastern China during the Recent Global Warming Hiatus Period and Its Possible Reason

Science.gov (United States)

Lei, T.; Li, S.; Luo, F.; Han, Z.

2017-12-01

The authors analyzed the observed winter surface air temperature in eastern mainland China during the recent global warming hiatus period through 1998-2013. The results suggest a substantial cooling trend of about -1.0°/decade in Eastern China, Northeast China and Southeast China. Mechanism exploration indicates that the displacement of the East Asian upper-tropospheric jet and the associated Rossby wave may have contributed to the cooling trend. A southward shift of the East Asian polar together with a northward shift of the subtropical jet caused the enhancement of the northern East Asian trough and Siberian High. A diagnostic analysis suggests that the Arctic sea ice loss, ENSO and North Atlantic SST all play a role. With the three factors removed, the air temperature trend is -0.35, -0.08 and -0.44°/decade over East China, Northeast China and Southeast China, respectively.

Precursory landforms and geologic structures of catastrophic landslides induced by typhoon Talas 2011 Japan (Invited)

Science.gov (United States)

Chigira, M.; Matsushi, Y.; Tsou, C.

2013-12-01

Our experience of catastrophic landslides induced by rainstorms and earthquakes in recent years suggests that many of them are preceded by deep-seated gravitational slope deformation. Deep-seated gravitational slope deformation continues slowly and continually and some of them transform into catastrophic failures, which cause devastating damage in wide areas. Some other types, however, do not change into catastrophic failure. Deep-seated gravitational slope deformation that preceded catastrophic failures induced by typhoon Talas 2011 Japan, had been surveyed with airborne laser scanner beforehand, of which high-resolution DEMs gave us an important clue to identify which type of topographic features of gravitational slope deformation is susceptible to catastrophic failure. We found that 26 of 39 deep-seated catastrophic landslides had small scarps along the heads of future landslides. These scarps were caused by gravitational slope deformation that preceded the catastrophic failure. Although the scarps may have been enlarged by degradation, their sizes relative to the whole slopes suggest that minimal slope deformation had occurred in the period immediately before the catastrophic failure. The scarp ratio, defined as the ratio of length of a scarp to that of the whole slope both measured along the slope line, ranged from 1% to 23%. 38% of the landslides with small scarps had scarp ratios less than 4%, and a half less than 8%. This fact suggests that the gravitational slope deformation preceded catastrophic failure was relatively small and may suggest that those slopes were under critical conditions just before catastrophic failure. The above scarp ratios may be characteristic to accretional complex with undulating, anastomosing thrust faults, which were major sliding surfaces of the typhoon-induced landslides. Eleven of the remaining 13 landslides occurred in landslide scars of previous landslides or occurred as an extension of landslide scars at the lower parts of

Elucidating Jet Energy Loss Using Jets: Prospects from ATLAS

International Nuclear Information System (INIS)

Grau, N.

2009-01-01

Jets at the LHC are expected to provide the testing ground for studying QCD energy loss. In this contribution, we briefly outline the strategy that will be used to measure jets in ATLAS and how we will go about studying energy loss. We describe the utility of measuring the jet R AA , the fragmentation function, and heavy flavor jets. Utilizing the collision energy provided by the LHC and the nearly hermetic and highly segmented calorimeter, ATLAS is expected to make important contributions to the understanding of parton energy loss using fully reconstructed jets.

Elucidating Jet Energy Loss Using Jets Prospects from ATLAS

CERN Document Server

Grau, N

2009-01-01

Jets at the LHC are expected to provide the testing ground for studying QCD energy loss. In this contribution, we briefly outline the strategy that will be used to measure jets in ATLAS and how we will go about studying energy loss. We describe the utility of measuring the jet $R_{AA}$, the fragmentation function, and heavy flavor jets. Utilizing the collision energy provided by the LHC and the nearly hermetic and highly segmented calorimeter, ATLAS is expected to make important contributions to the understanding of parton energy loss using fully reconstructed jets.

Breakup Behavior of Molten Wood's Metal Jet in Subcooled Water

Energy Technology Data Exchange (ETDEWEB)

Heo, Hyo; Park, Seong Dae; Bang, In Cheol [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of); Jerng, Dong Wook [Chung-Ang Univ., Seoul (Korea, Republic of)

2014-10-15

There are safety characteristics of the metal fueled sodium fast-cooled reactor (SFR), by identifying the possibility of early termination of severe accidents. If the molten fuel is ejected from the cladding, the ejected molten fuel can interact with the coolant in the reactor vessel. This phenomenon is called as fuel-coolant interaction (FCI). The FCI occurs at the initial phase leading to severe accidents like core disruptive accident (CDA) in the SFR. A part of the corium energy is intensively transferred to the coolant in a very short time during the FCI. The coolant vaporizes at high pressure and expands so results in steam explosion that can threat to the integrity of nuclear reactor. The intensity of steam explosion is determined by jet breakup and the fragmentation behavior. Therefore, it is necessary to understand the jet breakup between the molten fuel jet and the coolant in order to evaluate whether the steam explosion occurs or not. The liquid jet breakup has been studied in various areas, such as aerosols, spray and combustion. In early studies, small diameter jets of low density liquids were studied. The jet breakup for large density liquids has been studied in nuclear reactor field with respect to safety. The existence of vapor film layer between the melt and liquid fluid is only in case of large density breakup. This paper deals with the jet breakup experiment in non-boiling conditions in order to analyze hydraulic effect on the jet behavior. In the present study, the wood's metal was used as the jet material. It has similar properties to the metal fuel. The physical properties of molten materials and coolants are listed in Table I, respectively. It is easy to conduct the experiment due to low melting point of the wood's metal. In order to clarify the dominant factors determining jet breakup and size distribution of the debris, the experiment that the molten wood's metal was injected into the subcooled condition was conducted. The

A system for regulating the pressure of resuperheated steam in high temperature gas-cooled reactor power stations

International Nuclear Information System (INIS)

Braytenbah, A.S.; Jaegines, K.O.

1975-01-01

The invention relates to a system for regulating steam-pressure in the re-superheating portion of a steam-boiler receiving heat from a gas-cooled high temperature nuclear reactor, provided with gas distributing pumps driven by steam-turbines. The system comprises means for generating a pressure signal of desired magnitude for the re-superheating portion, and means for providing a real pressure in the re-superheating portion, means (including a by-passing device) for generating steam-flow rate signal of desired magnitude, a turbine by-pass device comprising a by-pass tapping means for regulating the steam-flow-rate in said turbine according to the desired steam-flow rate signal and means for controlling said by-pass tapping means according to said desired steam-flow-rate signal [fr

7 CFR 58.637 - Cooling the mix.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cooling the mix. 58.637 Section 58.637 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS AND STANDARDS UNDER THE...

From Catastrophizing to Recovery: a pilot study of a single-session treatment for pain catastrophizing

Directory of Open Access Journals (Sweden)

Darnall BD

2014-04-01

Full Text Available Beth D Darnall, John A Sturgeon, Ming-Chih Kao, Jennifer M Hah, Sean C MackeyDivision of Pain Medicine, Stanford Systems Neuroscience and Pain Laboratory, Stanford University School of Medicine, Palo Alto, CA, USABackground: Pain catastrophizing (PC – a pattern of negative cognitive-emotional responses to real or anticipated pain – maintains chronic pain and undermines medical treatments. Standard PC treatment involves multiple sessions of cognitive behavioral therapy. To provide efficient treatment, we developed a single-session, 2-hour class that solely treats PC entitled “From Catastrophizing to Recovery”[FCR].Objectives: To determine 1 feasibility of FCR; 2 participant ratings for acceptability, understandability, satisfaction, and likelihood to use the information learned; and 3 preliminary efficacy of FCR for reducing PC.Design and methods: Uncontrolled prospective pilot trial with a retrospective chart and database review component. Seventy-six patients receiving care at an outpatient pain clinic (the Stanford Pain Management Center attended the class as free treatment and 70 attendees completed and returned an anonymous survey immediately post-class. The Pain Catastrophizing Scale (PCS was administered at class check-in (baseline and at 2, and 4 weeks post-treatment. Within subjects repeated measures analysis of variance (ANOVA with Student's t-test contrasts were used to compare scores across time points.Results: All attendees who completed a baseline PCS were included as study participants (N=57; F=82%; mean age =50.2 years; PCS was completed by 46 participants at week 2 and 35 participants at week 4. Participants had significantly reduced PC at both time points (P<0001 and large effect sizes were found (Cohen's d=0.85 and d=1.15.Conclusion: Preliminary data suggest that FCR is an acceptable and effective treatment for PC. Larger, controlled studies of longer duration are needed to determine durability of response, factors

Effects of microtubule mechanics on hydrolysis and catastrophes

International Nuclear Information System (INIS)

Müller, N; Kierfeld, J

2014-01-01

We introduce a model for microtubule (MT) mechanics containing lateral bonds between dimers in neighboring protofilaments, bending rigidity of dimers, and repulsive interactions between protofilaments modeling steric constraints to investigate the influence of mechanical forces on hydrolysis and catastrophes. We use the allosteric dimer model, where tubulin dimers are characterized by an equilibrium bending angle, which changes from 0 ∘ to 22 ∘ by hydrolysis of a dimer. This also affects the lateral interaction and bending energies and, thus, the mechanical equilibrium state of the MT. As hydrolysis gives rise to conformational changes in dimers, mechanical forces also influence the hydrolysis rates by mechanical energy changes modulating the hydrolysis rate. The interaction via the MT mechanics then gives rise to correlation effects in the hydrolysis dynamics, which have not been taken into account before. Assuming a dominant influence of mechanical energies on hydrolysis rates, we investigate the most probable hydrolysis pathways both for vectorial and random hydrolysis. Investigating the stability with respect to lateral bond rupture, we identify initiation configurations for catastrophes along the hydrolysis pathways and values for a lateral bond rupture force. If we allow for rupturing of lateral bonds between dimers in neighboring protofilaments above this threshold force, our model exhibits avalanche-like catastrophe events. (papers)

Jets from jets: re-clustering as a tool for large radius jet reconstruction and grooming at the LHC

Science.gov (United States)

Nachman, Benjamin; Nef, Pascal; Schwartzman, Ariel; Swiatlowski, Maximilian; Wanotayaroj, Chaowaroj

2015-02-01

Jets with a large radius R ≳ 1 and grooming algorithms are widely used to fully capture the decay products of boosted heavy particles at the Large Hadron Collider (LHC). Unlike most discriminating variables used in such studies, the jet radius is usually not optimized for specific physics scenarios. This is because every jet configuration must be calibrated, insitu, to account for detector response and other experimental effects. One solution to enhance the availability of large- R jet configurations used by the LHC experiments is jet re-clustering. Jet re-clustering introduces an intermediate scale r groomed jets. Jet re-clustering has the benefit that no additional large-R calibration is necessary, allowing the re-clustered large radius parameter to be optimized in the context of specific precision measurements or searches for new physics.

Vapor condensation on the surface of a liquid blanket jet in an inertial-confinement fusion reactor

International Nuclear Information System (INIS)

Takahashi, Minoru; Inoue, Akira; Fujinuma, Hajime; Tsukui, Jun.

1991-01-01

As the fundamental study on lithium jet cooling of an inertial-confinement fusion reactor, the experiment was performed to investigate for the steady condensation of saturated steam on a vertical downward water jet. The experimental parameters were the nozzle diameter of 3 and 5 mm, the jet length of 60∼316 mm, the outlet velocity of 2∼12 m/s, the outlet temperature of 30∼70degC, and the pressure of 0.03∼0.44 MPa, which corresponds to the Reynolds number of 1.35 x 10 4 ∼2.71 x 10 5 and the Prandtl number of 1.0∼5.2. As the Reynolds number or the jet length is increased, the Stanton number decreases and then increases again. As the steam pressure is increased, it increases monotonously. These characteristics of condensation heat transfer have been classical into four regions based on the criteria for jet break-up and surface disturbance, or entrainment. The empirical correlations for the Stanton number have been obtained for these regions, and the validity was confirmed by comparing them with the previous correlations. (author)

Visualization of mole fraction distribution of slow jet forming stably stratified field

International Nuclear Information System (INIS)

Fumizawa, Motoo; Hishida, Makoto

1990-01-01

An experimental study has been performed to investigate the behavior of flow and mass transfer in gaseous slow jet in which buoyancy force opposed the flow forming stably stratified field. The study has been performed to understand the basic features of air ingress phenomena at pipe rupture accident of the high temperature gas-cooled reactor. A displacement fringe technique was adopted in Mach-Zehnder interferometer to visualize the mole fraction distribution. As the result, the followings were obtained: (1) The stably stratified fields were formed in the vicinity of the outlet of the slow jet. The penetration distance of the stably stratified fields increased with Froude number. (2) Mass fraction distributions in the stably stratified fields were well correlated with the present model using the ramp mole velocity profile. (author)

Study on China’s Earthquake Prediction by Mathematical Analysis and its Application in Catastrophe Insurance

Science.gov (United States)

Jianjun, X.; Bingjie, Y.; Rongji, W.

2018-03-01

The purpose of this paper was to improve catastrophe insurance level. Firstly, earthquake predictions were carried out using mathematical analysis method. Secondly, the foreign catastrophe insurances’ policies and models were compared. Thirdly, the suggestions on catastrophe insurances to China were discussed. The further study should be paid more attention on the earthquake prediction by introducing big data.

Optimization of thermal design for nitrogen shield of JET cryopump

International Nuclear Information System (INIS)

Baxi, C.B.; Obert, W.

1991-11-01

The reference design of JET cryopump nitrogen shield consists of an outer section made of copper chevrons fastened to two cooling tubes and an inner stainless steel section and backing plate with two cooling tubes. These tubes are fed in a parallel flow arrangement. The inlet flow is divided into two parallel paths so that both tubes on either section are always at the same temperature. This arrangement was selected due to concern about conduction between warm and cold parts of the shield during cooldown transients. If the heat loads are unequal, such a parallel flow arrangement can result in flow starvation in the path with higher heat load. This will cause large temperature differences and, ultimately, structural failure. Hence, an analysis was undertaken to investigate the conduction effects in the shield for other flow arrangements. 4 refs., 8 figs

Special software for computing the special functions of wave catastrophes

Directory of Open Access Journals (Sweden)

Andrey S. Kryukovsky

2015-01-01

Full Text Available The method of ordinary differential equations in the context of calculating the special functions of wave catastrophes is considered. Complementary numerical methods and algorithms are described. The paper shows approaches to accelerate such calculations using capabilities of modern computing systems. Methods for calculating the special functions of wave catastrophes are considered in the framework of parallel computing and distributed systems. The paper covers the development process of special software for calculating of special functions, questions of portability, extensibility and interoperability.

Simulation of attenuation of thermal fluctuations near a plate impinged by jets

International Nuclear Information System (INIS)

Simoneau, J.P.

2001-01-01

In nuclear reactors, and especially in liquid sodium cooled ones, the combination of temperature differences inside cooling fluid, turbulent flows and high heat transfer coefficients is a potential source of the thermal striping process. Such a phenomenon has been studied for several years by using Large Eddy Simulation models. The present paper focuses on the attenuation of the thermal fluctuations in the boundary layer. The knowledge of this amplitude reduction is of prime importance for subsequent mechanical analyses. A Large Eddy Simulation model is implemented in the Star-cd code, including discretization of the viscous sublayer. The numerical simulation of two parallel jets impinging a flat plate in water is then performed and positively compared to corresponding experimental results. (author)

A unified approach of catastrophic events

Directory of Open Access Journals (Sweden)

S. Nikolopoulos

2004-01-01

Full Text Available Although there is an accumulated charge of theoretical, computational, and numerical work, like catastrophe theory, bifurcation theory, stochastic and deterministic chaos theory, there is an important feeling that these matters do not completely cover the physics of real catastrophic events. Recent studies have suggested that a large variety of complex processes, including earthquakes, heartbeats, and neuronal dynamics, exhibits statistical similarities. Here we are studying in terms of complexity and non linear techniques whether isomorphic signatures emerged indicating the transition from the normal state to the both geological and biological shocks. In the last 15 years, the study of Complex Systems has emerged as a recognized field in its own right, although a good definition of what a complex system is, actually is eluded. A basic reason for our interest in complexity is the striking similarity in behaviour close to irreversible phase transitions among systems that are otherwise quite different in nature. It is by now recognized that the pre-seismic electromagnetic time-series contain valuable information about the earthquake preparation process, which cannot be extracted without the use of important computational power, probably in connection with computer Algebra techniques. This paper presents an analysis, the aim of which is to indicate the approach of the global instability in the pre-focal area. Non-linear characteristics are studied by applying two techniques, namely the Correlation Dimension Estimation and the Approximate Entropy. These two non-linear techniques present coherent conclusions, and could cooperate with an independent fractal spectral analysis to provide a detection concerning the emergence of the nucleation phase of the impending catastrophic event. In the context of similar mathematical background, it would be interesting to augment this description of pre-seismic electromagnetic anomalies in order to cover biological

Analysis of the flow structure of a turbulent thermal plasma jet

International Nuclear Information System (INIS)

Spores, R.A.

1989-01-01

The goal of this research project is to attain a better understanding of the fluid mechanics associated with the high temperature jet of a thermal plasma torch. The analysis of a plasma, which has the ability to vaporize anything placed inside it without proper cooling, presents a unique research challenge. Several types of non-intrusive diagnostic techniques has been used to examine the jet from different perspectives. To actually map out the mean gas velocities and turbulence intensities throughout the jet, laser Doppler anemometry has been employed. The plasma gas and entrained air him been seeded separately in order to conditionally sample the two fluids and attain information about the gas mixing process. Both radial and axial turbulence levels have been measured in order to analyze the non-isotropic nature of the jet. A parabolic numerical code has been modified and compared with the obtained experimental results. A new diagnostic technique for plasma torches, which involves the spectral analysis of voltage, optical (temperature), and acoustical (pressure) fluctuations, has been implemented. The acoustical spectrum can provide information about the existence of coherent structures in the flow while the cross correlation of the acoustical signal with the voltage fluctuations can tell one to what extent perturbations of the internal arc affect the external flow. Since temperature is a scalar that is dependent on the flow field, observing temperature fluctuations can likewise help one to understand the mechanics of the flow. Flow visualization of the plasma jet using a high speed video camera has also been undertaken in order to better understand the entrainment process

Structure of natural draft cooling towers, 1. Study on cooling tower shells

Energy Technology Data Exchange (ETDEWEB)

Ishioka, H; Sakamoto, Y; Tsurusaki, M; Koshizawa, K; Chiba, T [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1976-09-01

Recently in Japan, demands for cooling tower systems have been increasing remarkably with the construction of large power plants and the legislation of environmental regulations. In view of the severe natural conditions in Japan such as strong wind and seismic loadings, etc., the establishment of the optimum design and construction method is essential for the building of safe and economical towers. In order to establish a comprehensive plan of a power plant cooling system of the appropriate structural type, the authors have made researches and experiments on design conditions, static and dynamic analyses, and comparative studies of various structural types such as reinforced concrete thin-shell structures, steel framed structures and composite shell segment structures, based on the investigation results of towers in Europe and America. These results are presented in three reports, the 1st of which concerns cooling tower shells as are herein described.

Gravothermal catastrophe of finite amplitude

Energy Technology Data Exchange (ETDEWEB)

Hachisu, I; Sugimoto, D [Tokyo Univ. (Japan). Coll. of General Education; Nakada, Y; Nomoto, K

1978-08-01

Development of the gravothermal catastrophe is followed numerically for self-gravitating gas system enclosed by an adiabatic wall, which is isothermal in the initial state. It is found that the final fate of the catastrophe is in two ways depending on the initial perturbations. When the initial perturbation produces a temperature distribution decreasing outward, the contraction proceeds in the central region and the central density increases unlimitedly, as the heat flows outward. When the initial temperature distribution is increasing outward, on the other hand, the central region expands as the heat flows into the central region. Then the density contrast is reduced and finally the system reaches another isothermal configuration with the same energy but with a lower density contrast and a higher entropy. This final configuration is gravothermally stable and may be called a thermal system. In the former case of the unlimited contraction, the final density profile is determined essentially by the density and temperature dependence of the heat conductivity. In the case of a system under the force of the inverse square law, the final density distribution is well approximated by a power law so that the mass contained in the condensed core is relatively small. A possibility of formation of a black hole in stellar systems is also discussed.

Gravothermal catastrophe of finite amplitude

International Nuclear Information System (INIS)

Hachisu, Izumi; Sugimoto, Daiichiro; Nakada, Yoshikazu; Nomoto, Ken-ichi.

1978-01-01

Development of the gravothermal catastrophe is followed numerically for self-gravitating gas system enclosed by an adiabatic wall, which is isothermal in the initial state. It is found that the final fate of the catastrophe is in two ways depending on the initial perturbations. When the initial perturbation produces a temperature distribution decreasing outward, the contraction proceeds in the central region and the central density increases unlimitedly, as the heat flows outward. When the initial temperature distribution is increasing outward, on the other hand, the central region expands as the heat flows into the central region. Then the density contrast is reduced and finally the system reaches another isothermal configuration with the same energy but with a lower density contrast and a higher entropy. This final configuration is gravothermally stable and may be called a thermal system. In the former case of the unlimited contraction, the final density profile is determined essentially by the density and temperature dependence of the heat conductivity. In the case of a system under the force of the inverse square law, the final density distribution is well approximated by a power law so that the mass contained in the condensed core is relatively small. A possibility of formation of a black hole in stellar systems is also discussed. (author)

Catastrophic risk : Social influences on insurance decisions

NARCIS (Netherlands)

Krawczyk, Michal; Trautmann, Stefan; van de Kuilen, Gijs

We study behavioral patterns of insurance demand for low-probability large-loss events (catastrophic losses). Individual patterns of belief formation and risk attitude that were suggested in the behavioral decisions literature emerge robustly in the current set of insurance choices. However, social

A Technology Demonstration Experiment for Laser Cooled Atomic Clocks in Space

Science.gov (United States)

Klipstein, W. M.; Kohel, J.; Seidel, D. J.; Thompson, R. J.; Maleki, L.; Gibble, K.

2000-01-01

We have been developing a laser-cooling apparatus for flight on the International Space Station (ISS), with the intention of demonstrating linewidths on the cesium clock transition narrower than can be realized on the ground. GLACE (the Glovebox Laser- cooled Atomic Clock Experiment) is scheduled for launch on Utilization Flight 3 (UF3) in 2002, and will be mounted in one of the ISS Glovebox platforms for an anticipated 2-3 week run. Separate flight definition projects funded at NIST and Yale by the Micro- gravity Research Division of NASA as a part of its Laser Cooling and Atomic Physics (LCAP) program will follow GLACE. Core technologies for these and other LCAP missions are being developed at JPL, with the current emphasis on developing components such as the laser and optics subsystem, and non-magnetic vacuum-compatible mechanical shutters. Significant technical challenges in developing a space qualifiable laser cooling apparatus include reducing the volume, mass, and power requirements, while increasing the ruggedness and reliability in order to both withstand typical launch conditions and achieve several months of unattended operation. This work was performed at the Jet Propulsion Laboratory under a contract with the National Aeronautics and Space Administration.

Experimental Study of the Twin Turbulent Water Jets Using Laser Doppler Anemometry for Validating Numerical Models

International Nuclear Information System (INIS)

Wang Huhu; Lee Saya; Hassan, Yassin A.; Ruggles, Arthur E.

2014-01-01

The design of next generation (Gen. IV) high-temperature nuclear reactors including gas-cooled and sodium-cooled ones involves massive numerical works especially the Computational Fluid Dynamics (CFD) simulations. The high cost of large-scale experiments and the inherent uncertainties existing in the turbulent models and wall functions of any CFD codes solving Reynolds-averaged Navier-Stokes (RANS) equations necessitate the high-spacial experimental data sets for benchmarking the simulation results. In Gen. IV conceptual reactors, the high- temperature flows mix in the upper plenum before entering the secondary cooling system. The mixing condition should be accurately estimated and fully understood as it is related to the thermal stresses induced in the upper plenum and the magnitudes of output power oscillations due to any changes of primary coolant temperature. The purpose of this study is to use Laser Doppler Anemometry (LDA) technique to measure the flow field of two submerged parallel jets issuing from two rectangular channels. The LDA data sets can be used to validate the corresponding simulation results. The jets studied in this work were at room temperature. The turbulent characteristics including the distributions of mean velocities, turbulence intensities, Reynolds stresses were studied. Uncertainty analysis was also performed to study the errors involved in this experiment. The experimental results in this work are valid for benchmarking any steady-state numerical simulations using turbulence models to solve RANS equations. (author)

On the Numerical and Experimental Study of Spray Cooling

Directory of Open Access Journals (Sweden)

M.R. Guechi

2013-12-01

Full Text Available The spraying of an impinging jet is an effective way to cool heated surfaces. The objective of this study is to develop a numerical model to predict the heat transfer with phase change between a hot plate surface and a two-phase impinging jet. Different two-phase modeling approaches (Lagrangian and Eulerian methods are compared. The influence of the spray nozzle operating conditions and of the distance between the nozzle exit and the surface impact is analyzed. The numerical results are compared with measurements obtained on an experimental test bench. The confrontation numerical/experimental is carried out by comparing the distribution of temperature at the surface of the plate and the heat transfer coefficient. This comparison shows that it is the Eulerian model which seems most capable to take into account the evaporation of the droplets in contact with the heated plate. However, the simulation performed with this model show a strong dependence of the results to the turbulence model used.

Diagnosis and management of catastrophic antiphospholipid syndrome.

Science.gov (United States)

Carmi, Or; Berla, Maya; Shoenfeld, Yehuda; Levy, Yair

2017-04-01

Catastrophic antiphospholipid syndrome (CAPS) is a rare, life-threatening disease. In 1992, Asherson defined it as a widespread coagulopathy related to the antiphospholipid antibodies (aPL). CAPS requires rapid diagnosis and prompt initiation of treatment. Areas covered: This paper discusses all aspects of CAPS, including its pathophysiology, clinical manifestations, diagnostic approaches, differential diagnoses, management and treatment of relapsing CAPS, and its prognosis. To obtain the information used in this review, scientific databases were searched using the key words antiphospholipid antibodies, catastrophic antiphospholipid syndrome, hemolytic anemia, lupus anticoagulant, and thrombotic microangiopathic hemolytic anemia. Expert commentary: CAPS is a rare variant of the antiphospholipid syndrome (APS). It is characterized by thrombosis in multiple organs and a cytokine storm developing over a short period, with histopathologic evidence of multiple microthromboses, and laboratory confirmation of high aPL titers. This review discusses the diagnostic challenges and current approaches to the treatment of CAPS.

Intestinal malrotation and catastrophic volvulus in infancy.

Science.gov (United States)

Lee, Henry Chong; Pickard, Sarah S; Sridhar, Sunita; Dutta, Sanjeev

2012-07-01

Intestinal malrotation in the newborn is usually diagnosed after signs of intestinal obstruction, such as bilious emesis, and corrected with the Ladd procedure. The objective of this report is to describe the presentation of severe cases of midgut volvulus presenting in infancy, and to discuss the characteristics of these cases. We performed a 7-year review at our institution and present two cases of catastrophic midgut volvulus presenting in the post-neonatal period, ending in death soon after the onset of symptoms. These two patients also had significant laboratory abnormalities compared to patients with more typical presentations resulting in favorable outcomes. Although most cases of intestinal malrotation in infancy can be treated successfully, in some circumstances, patients' symptoms may not be detected early enough for effective treatment, and therefore may result in catastrophic midgut volvulus and death. Copyright © 2012 Elsevier Inc. All rights reserved.

Formation of X-ray emitting stationary shocks in magnetized protostellar jets

Science.gov (United States)

Ustamujic, S.; Orlando, S.; Bonito, R.; Miceli, M.; Gómez de Castro, A. I.; López-Santiago, J.

2016-12-01

Context. X-ray observations of protostellar jets show evidence of strong shocks heating the plasma up to temperatures of a few million degrees. In some cases, the shocked features appear to be stationary. They are interpreted as shock diamonds. Aims: We investigate the physics that guides the formation of X-ray emitting stationary shocks in protostellar jets; the role of the magnetic field in determining the location, stability, and detectability in X-rays of these shocks; and the physical properties of the shocked plasma. Methods: We performed a set of 2.5-dimensional magnetohydrodynamic numerical simulations that modelled supersonic jets ramming into a magnetized medium and explored different configurations of the magnetic field. The model takes into account the most relevant physical effects, namely thermal conduction and radiative losses. We compared the model results with observations, via the emission measure and the X-ray luminosity synthesized from the simulations. Results: Our model explains the formation of X-ray emitting stationary shocks in a natural way. The magnetic field collimates the plasma at the base of the jet and forms a magnetic nozzle there. After an initial transient, the nozzle leads to the formation of a shock diamond at its exit which is stationary over the time covered by the simulations ( 40-60 yr; comparable with timescales of the observations). The shock generates a point-like X-ray source located close to the base of the jet with luminosity comparable with that inferred from X-ray observations of protostellar jets. For the range of parameters explored, the evolution of the post-shock plasma is dominated by the radiative cooling, whereas the thermal conduction slightly affects the structure of the shock. A movie is available at http://www.aanda.org

UNDERCOVER EUV SOLAR JETS OBSERVED BY THE INTERFACE REGION IMAGING SPECTROGRAPH

Energy Technology Data Exchange (ETDEWEB)

Chen, N.-H. [Korea Astronomy and Space Science Institute, Daejeon (Korea, Republic of); Innes, D. E. [Max-Planck-Institut für Sonnensystemforschung, D-37077 Göttingen (Germany)

2016-12-10

It is well-known that extreme ultraviolet (EUV) emission emitted at the solar surface is absorbed by overlying cool plasma. Especially in active regions, dark lanes in EUV images suggest that much of the surface activity is obscured. Simultaneous observations from the Interface Region Imaging Spectrograph, consisting of UV spectra and slit-jaw images (SJI), give vital information with sub-arcsecond spatial resolution on the dynamics of jets not seen in EUV images. We studied a series of small jets from recently formed bipole pairs beside the trailing spot of active region 11991, which occurred on 2014 March 5 from 15:02:21 UT to 17:04:07 UT. Collimated outflows with bright roots were present in SJI 1400 Å (transition region) and 2796 Å (upper chromosphere) that were mostly not seen in Atmospheric Imaging Assembly (AIA) 304 Å (transition region) and AIA 171 Å (lower corona) images. The Si iv spectra show a strong blue wing enhancement, but no red wing, in the line profiles of the ejecta for all recurrent jets, indicating outward flows without twists. We see two types of Mg ii line profiles produced by the jets spires: reversed and non-reversed. Mg ii lines remain optically thick, but turn optically thin in the highly Doppler shifted wings. The energy flux contained in each recurrent jet is estimated using a velocity differential emission measure technique that measures the emitting power of the plasma as a function of the line-of-sight velocity. We found that all the recurrent jets release similar energy (10{sup 8} erg cm{sup −2} s{sup −1}) toward the corona and the downward component is less than 3%.

Dyadic analysis of child and parent trait and state pain catastrophizing in the process of children's pain communication.

Science.gov (United States)

Birnie, Kathryn A; Chambers, Christine T; Chorney, Jill; Fernandez, Conrad V; McGrath, Patrick J

2016-04-01

When explored separately, child and parent catastrophic thoughts about child pain show robust negative relations with child pain. The objective of this study was to conduct a dyadic analysis to elucidate intrapersonal and interpersonal influences of child and parent pain catastrophizing on aspects of pain communication, including observed behaviours and perceptions of child pain. A community sample of 171 dyads including children aged 8 to 12 years (89 girls) and parents (135 mothers) rated pain catastrophizing (trait and state versions) and child pain intensity and unpleasantness following a cold pressor task. Child pain tolerance was also assessed. Parent-child interactions during the cold pressor task were coded for parent attending, nonattending, and other talk, and child symptom complaints and other talk. Data were analyzed using the actor-partner interdependence model and hierarchical multiple regressions. Children reporting higher state pain catastrophizing had greater symptom complaints regardless of level of parent state pain catastrophizing. Children reporting low state pain catastrophizing had similar high levels of symptom complaints, but only when parents reported high state pain catastrophizing. Higher child and parent state and/or trait pain catastrophizing predicted their own ratings of higher child pain intensity and unpleasantness, with child state pain catastrophizing additionally predicting parent ratings. Higher pain tolerance was predicted by older child age and lower child state pain catastrophizing. These newly identified interpersonal effects highlight the relevance of the social context to children's pain expressions and parent perceptions of child pain. Both child and parent pain catastrophizing warrant consideration when managing child pain.

Financial catastrophe and poverty impacts of out-of-pocket health payments in Turkey.

Science.gov (United States)

Özgen Narcı, Hacer; Şahin, İsmet; Yıldırım, Hasan Hüseyin

2015-04-01

To determine the prevalence of catastrophic health payments, examine the determinants of catastrophic expenditures, and assess the poverty impact of out-of-pocket (OOP) payments. Data came from the 2004 to 2010 Household Budget Survey. Catastrophic health spending was defined by health payments as percentage of household consumption expenditures and capacity to pay at a set of thresholds. The poverty impact was evaluated by poverty head counts and poverty gaps before and after OOP health payments. The percentage of households that catastrophically spent their consumption expenditure and capacity to pay increased from 2004 to 2010, regardless of the threshold used. Households with a share of more than 40% health spending in both consumption expenditure and capacity to pay accounted for less than 1% across years. However, when a series of potential confounders were taken into account, the study found statistically significantly increased risk for the lowest threshold and decreased risk for the highest threshold in 2010 relative to the base year. Household income, size, education, senior and under 5-year-old members, health insurance, disabled members, payment for inpatient care and settlement were also statistically significant predictors of catastrophic health spending. Overall, poverty head counts were below 1%. Poverty gaps reached a maximum of 0.098%, with an overall increase in 2010 compared to 2004. Catastrophe and poverty increased from 2004 to 2010. However, given that the realization of some recent policies will affect the financial burden of OOP payments on households, the findings of this study need to be replicated.

A comparison of catastrophic injury incidence rates by Provincial Rugby Union in South Africa.

Science.gov (United States)

Badenhorst, Marelise; Verhagen, Evert A L M; van Mechelen, Willem; Lambert, Michael I; Viljoen, Wayne; Readhead, Clint; Baerecke, Gail; Brown, James C

2017-07-01

To compare catastrophic injury rates between the 14 South African Provincial Rugby Unions. A prospective, population-based study conducted among all South African Unions between 2008-2014. Player numbers in each Union were obtained from South African Rugby's 2013 Census. Catastrophic injuries were analysed from BokSmart's serious injury database. Incidence rates with 95% Confidence Intervals were calculated. Catastrophic injuries (Acute Spinal Cord Injuries and catastrophic Traumatic Brain Injuries) within Unions were compared statistically, using a Poisson regression with Incidence Rate Ratios (IRR) and a 95% confidence level (pUnion ranged from 1.8 per 100000 players (95% CI: 0.0-6.5) to 7.9 (95% CI: 0.0-28.5) per 100000 players per year. The highest incidence rate of permanent outcome Acute Spinal Cord Injuries was reported at 7.1 per 100000 players (95% CI: 0.0-17.6). Compared to this Union, five (n=5/14, 36%) of the Unions had significantly lower incidence rates of Acute Spinal Cord Injuries. Proportionately, three Unions had more Acute Spinal Cord Injuries and three other Unions had more catastrophic Traumatic Brain Injuries. There were significant differences in the catastrophic injury incidence rates amongst the Provincial Unions in South Africa. Future studies should investigate the underlying reasons contributing to these provincial differences. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Jet fragmentation

International Nuclear Information System (INIS)

Saxon, D.H.

1985-10-01

The paper reviews studies on jet fragmentation. The subject is discussed under the topic headings: fragmentation models, charged particle multiplicity, bose-einstein correlations, identified hadrons in jets, heavy quark fragmentation, baryon production, gluon and quark jets compared, the string effect, and two successful models. (U.K.)

Public policy and risk financing strategies for global catastrophe risk management - the role of global risk initiatives

Science.gov (United States)

McSharry, Patrick; Mitchell, Andrew; Anderson, Rebecca

2010-05-01

Decision-makers in both public and private organisations depend on accurate data and scientific understanding to adequately address climate change and the impact of extreme events. The financial impacts of catastrophes on populations and infrastructure can be offset through effective risk transfer mechanisms, structured to reflect the specific perils and levels of exposure to be covered. Optimal strategies depend on the likely socio-econonomic impact, the institutional framework, the overall objectives of the covers placed and the level of both the frequency and severity of loss potential expected. The diversity of approaches across different countries has been documented by the Spanish "Consorcio de Compensación de Seguros". We discuss why international public/private partnerships are necessary for addressing the risk of natural catastrophes. International initiatives such as the Global Earthquake Model (GEM) and the World Forum of Catastrophe Programmes (WFCP) can provide effective guidelines for constructing natural catastrophe schemes. The World Bank has been instrumental in the creation of many of the existing schemes such as the Turkish Catastrophe Insurance Pool, the Caribbean Catastrophe Risk Insurance Facility and the Mongolian Index-Based Livestock Insurance Program. We review existing schemes and report on best practice in relation to providing protection against natural catastrophe perils. The suitability of catastrophe modelling approaches to support schemes across the world are discussed and we identify opportunities to improve risk assessment for such schemes through transparent frameworks for quantifying, pricing, sharing and financing catastrophe risk on a local and global basis.

JET Joint Undertaking

International Nuclear Information System (INIS)

Keen, B.E.; Lallia, P.; O'Hara, G.W.; Pollard, I.E.

1987-06-01

The paper presents the annual report of the Joint European Torus (JET) Joint Undertaking, 1986. The report is divided into two parts: a part on the scientific and technical programme of the project, and a part setting out the administration and organisation of the Project. The first part includes: a summary of the main features of the JET apparatus, the JET experimental programme, the position of the Project in the overall Euratom programme, and how JET relates to other large fusion devices throughout the world. In addition, the technical status of JET is described, as well as the results of the JET operations in 1986. The final section of the first part outlines the proposed future programme of JET. (U.K.)

Catastrophe risk data scoping for disaster risk finance in Asia

Science.gov (United States)

Millinship, Ian; Revilla-Romero, Beatriz

2017-04-01

Developing countries across Latin America, Africa, and Asia are some of the most exposed to natural catastrophes in the world. Over the last 20 years, Asia has borne almost half the estimated global economic cost of natural disasters - around 53billion annually. Losses from natural disasters can damage growth and hamper economic development and unlike in developed countries where risk is reallocated through re/insurance, typically these countries rely on budget reallocations and donor assistance in order to attempt to meet financing needs. There is currently an active international dialogue on the need to increase access to disaster risk financing solutions in Asia. The World Bank-GFDRR Disaster Risk Financing and Insurance Program with financial support from the Rockefeller Foundation, is currently working to develop regional options for disaster risk financing for developing countries in Asia. The first stage of this process has been to evaluate available catastrophe data suitable to support the design and implementation of disaster risk financing mechanisms in selected Asian countries. This project was carried out by a consortium of JBA Risk Management, JBA Consulting, ImageCat and Cat Risk Intelligence. The project focuses on investigating potential data sources for fourteen selected countries in Asia, for flood, tropical cyclone, earthquake and drought perils. The project was carried out under four stages. The first phase focused to identify and catalogue live/dynamic hazard data sources such as hazard gauging networks, or earth observations datasets which could be used to inform a parametric trigger. Live data sources were identified that provide credibility, transparency, independence, frequent reporting, consistency and stability. Data were catalogued at regional level, and prioritised at local level for five countries: Bangladesh, Indonesia, Pakistan, Sri Lanka and Viet Nam. The second phase was to identify, catalogue and evaluate catastrophe risk models

Analysis of the reliability of quality assurance of welded nuclear pressure vessels with regard to catastrophic failure

Energy Technology Data Exchange (ETDEWEB)

Ostberg, G [Lund Institute of Technology, Dept. of Materials Engineering (Sweden); Klingenstierna, B [FTL, Military Electronics Laboratory, National Defence Research Institute, Stockholm (Sweden); Sjoberg, L [Goteborg Univ., Dept. of Psychology (Sweden)

1976-07-01

The project is described as an analysis of the reliability of quality assurance of welded nuclear pressure vessels with regard to catastrophic failure. Its scope extends both beyond previous statistical evaluations of the risk of catastrophic failure, beyond previous studies of human malfunction, and beyond current studies of probabilistic fracture mechanics. The latter deal only with 'normal' data and 'normal' processes and procedures according to established rules and regulations, where as the present study concerns deficiencies or more or less complete fallacies of normal procedures and processes. Hopefully such events will prove to be rare enough to be characterized as 'unique'; this, in turn, means that the result of the investigation is not a new statistical figure but rather a survey of types and frequencies of errors and error-producing conditions. The emphasis is on the main pressure vessel; related information on the primary circuit is included, only when this can be done without excessive effort or costs. The avenues of approach in terms of technical-academic disciplines are reliability techniques and the psychology of analysis work and control processes.

Safeguards as catastrophic risk management: insights and projections

International Nuclear Information System (INIS)

Leffer, T.N.

2013-01-01

The system of international agreements designed to prevent the use of nuclear weapons and to control the spread of nuclear weapons, materials and technologies (collectively referred to as the nuclear arms control and nonproliferation regimes) is posited as humanity.s first attempt to mitigate a man-made global catastrophic risk. By extrapolating general principles of government response to risk from the arms control and nonproliferation regimes, a model of international regime building for catastrophic risk mitigation is constructed. This model provides the context for an examination of the system of safeguards implemented by the International Atomic Energy Agency (IAEA), which serves as the nuclear nonproliferation regime.s verification and enforcement mechanism and thereby constitutes the regime's most completely developed discrete mechanism for risk mitigation (a 'system within a system'). An assessment of the history, evolution and effectiveness of the IAEA safeguards system in the context of the regimes-as-risk-mitigation model reveals some general principles for risk-mitigation regimes which are then applied to the safeguards system to identify ways in which it may be strengthened. Finally, the IAEA safeguards system is posited as the prototype verification/enforcement mechanism for future risk mitigation regimes that governments will be compelled to create in the face of new global catastrophic risks that technological advance will inevitably create. (author)

Optimism Moderates the Influence of Pain Catastrophizing on Shoulder Pain Outcome: A Longitudinal Analysis.

Science.gov (United States)

Coronado, Rogelio A; Simon, Corey B; Lentz, Trevor A; Gay, Charles W; Mackie, Lauren N; George, Steven Z

2017-01-01

Study Design Secondary analysis of prospectively collected data. Background An abundance of evidence has highlighted the influence of pain catastrophizing and fear avoidance on clinical outcomes. Less is known about the interaction of positive psychological resources with these pain-associated distress factors. Objective To assess whether optimism moderates the influence of pain catastrophizing and fear avoidance on 3-month clinical outcomes in patients with shoulder pain. Methods Data from 63 individuals with shoulder pain (mean ± SD age, 38.8 ± 14.9 years; 30 female) were examined. Demographic, psychological, and clinical characteristics were obtained at baseline. Validated measures were used to assess optimism (Life Orientation Test-Revised), pain catastrophizing (Pain Catastrophizing Scale), fear avoidance (Fear-Avoidance Beliefs Questionnaire physical activity subscale), shoulder pain intensity (Brief Pain Inventory), and shoulder function (Pennsylvania Shoulder Score function subscale). Shoulder pain and function were reassessed at 3 months. Regression models assessed the influence of (1) pain catastrophizing and optimism and (2) fear avoidance and optimism. The final multivariable models controlled for factors of age, sex, education, and baseline scores, and included 3-month pain intensity and function as separate dependent variables. Results Shoulder pain (mean difference, -1.6; 95% confidence interval [CI]: -2.1, -1.2) and function (mean difference, 2.4; 95% CI: 0.3, 4.4) improved over 3 months. In multivariable analyses, there was an interaction between pain catastrophizing and optimism (β = 0.19; 95% CI: 0.02, 0.35) for predicting 3-month shoulder function (F = 16.8, R 2 = 0.69, Poptimism lessened the influence of pain catastrophizing on function. There was no evidence of significant moderation of fear-avoidance beliefs for 3-month shoulder pain (P = .090) or function (P = .092). Conclusion Optimism decreased the negative influence of pain

Active Control of Transverse Jets for Film Cooling Applications: A Limited Statement of Work

National Research Council Canada - National Science Library

Nikitopoulos, D. E

2006-01-01

.... A theoretical analysis was conducted and mechanisms that can play a defining role in film cooling control were identified on the basis of fundamental fluid-dynamics, prior experiments and preliminary...

Blob Formation and Ejection in Coronal Jets due to the Plasmoid and Kelvin–Helmholtz Instabilities

Energy Technology Data Exchange (ETDEWEB)

Ni, Lei; Lin, Jun [Yunnan Observatories, Chinese Academy of Sciences, 396 Yangfangwang, Guandu District, Kunming, 650216 (China); Zhang, Qing-Min [Key Laboratory for Dark Matter and Space Science, Purple Mountain Observatory, Chinese Academy of Sciences, Nanjing 210008 (China); Murphy, Nicholas A., E-mail: leini@ynao.ac.cn [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA 02138 (United States)

2017-05-20

We perform 2D resistive magnetohydrodynamic simulations of coronal jets driven by flux emergence along the lower boundary. The reconnection layers are susceptible to the formation of blobs that are ejected in the jet. Our simulation with low plasma β (Case I) shows that magnetic islands form easily and propagate upward in the jet. These islands are multithermal and thus are predicted to show up in hot channels (335 Å and 211 Å) and the cool channel (304 Å) in observations by the Atmospheric Imaging Assembly (AIA) on the Solar Dynamics Observatory . The islands have maximum temperatures of 8 MK, lifetimes of 120 s, diameters of 6 Mm, and velocities of 200 km s{sup −1}. These parameters are similar to the properties of blobs observed in extreme-ultraviolet (EUV) jets by AIA. The Kelvin–Helmholtz instability develops in our simulation with moderately high plasma β (Case II) and leads to the formation of bright vortex-like blobs above the multiple high magnetosonic Mach number regions that appear along the jet. These vortex-like blobs can also be identified in the AIA channels. However, they eventually move downward and disappear after the high magnetosonic Mach number regions disappear. In the lower plasma β case, the lifetime for the jet is shorter, the jet and magnetic islands are formed with higher velocities and temperatures, the current-sheet fragments are more chaotic, and more magnetic islands are generated. Our results show that the plasmoid instability and Kelvin–Helmholtz instability along the jet are both possible causes of the formation of blobs observed at EUV wavelengths.

Active control of continuous air jet with bifurcated synthetic jets

Directory of Open Access Journals (Sweden)

Dančová Petra

2017-01-01