WorldWideScience

Sample records for jacks mechanical equipment

  1. Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

    International Nuclear Information System (INIS)

    Gillett, J.E.; Wineman, A.L.

    1984-01-01

    A jacking mechanism is described for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns have a pin structure which rides up and down in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring bolt holes through the locking plates into alignment with a set of bolt holes in the housing, there being a set of such housing bolt holes corresponding to both a raised and a lowered position of the support column. When the locking plate is so aligned, a surface of the locking plate mates with a surface in the housing such that the support column is then supported by the locking plate and not by the ball jacks. Since the locking plates are to be installed and bolted to the housing during periods of reactor operation, the ball jacks need not be sized to react the large forces which occur or potentially could occur on the upper internals structure of the reactor during operation. The locking plates react these loads. The ball jacks, used only during refueling, can be smaller, which enable conventionally available equipment to fulfill the precision requirements for the task within available space

  2. TOPOLOGICAL STRUCTURE AND MOBILITY OF THE MECHANISMS USED IN CAR MECHANICAL JACKS

    Directory of Open Access Journals (Sweden)

    Viorica VELIȘCU

    2015-05-01

    Full Text Available This paper presents a structural analysis of the mechanism of high topological type jack - screw and translator rectilinear- patina and mobility mechanism analysis using various generally applicable formulas.

  3. Visit at PFAFF Silberblau for follow -up of mechanical jacks fabrication for HF

    CERN Multimedia

    Hubert Gerwig

    2000-01-01

    The HF detctor is sitting on either side of the CMS experiment at a height of the beam, 8.79m This detector weighs 220 tons will be lifted in 4 steps on its working position. 4 mechanical jacks with 100t force each will act on each corner of rectangle of 5600mm x 3200mm. The individual main pieces of the jacks are shown here. Next step is the assembly of the jacks by putting together housing, groundplate, spindle, gear, worm gear etc. Delivery of the first 4 jacks in dec.2000

  4. Multi-function magnetic jack control drive mechanism

    International Nuclear Information System (INIS)

    Bollinger, L.R.; Crawford, D.C.

    1986-01-01

    A multi-function magnetic jack control drive mechanism is described for controlling a nuclear reactor comprising: an elongate pressure housing; closely-spaced drive rods located in the pressure housing, the drive rod being connected to a reactor rod which is insertable in a reactor core; electrochemical stationary latch means which are selectively actuatable for holding a respective one of the drive rods stationary with respect to the pressure housing, the plurality of stationary latch means including at least one coil located about the pressure housing; longitudinally spaced electromechanical movable latch means, individually associated with one of the drive rods and each including a base for the drive rod associated therewith, for, when actuated, holding the associated drive rod stationary with respect to the base associated therewith, the movable latch means including an associated coil located about the pressure housing; and longitudinally spaced electromechanical lift means, individually associated with the base, for, when actuated, moving an associated base longitudinally along the pressure housing from a first position to a second position to thereby enable movement of one or more of the other drive rods longitudinally independently of the other drive rods in response to sequential and repeated operation of the electromechanical means, the lift means including an associated coil located about the pressure housing

  5. Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

    International Nuclear Information System (INIS)

    Gillett, J.E.; Wineman, A.L.

    1983-01-01

    A jacking mechanism for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns each have a pin which rides in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring the locking plates into engagement with the housing in a raised or a lowered position of the support column such that the support column is then supported by the locking plate and not by the ball screw jacks. (author)

  6. Lifetime of Mechanical Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Leland, K.

    1999-07-01

    The gas plant at Kaarstoe was built as part of the Statpipe gas transport system and went on stream in 1985. In 1993 another line was routed from the Sleipner field to carry condensate, and the plant was extended accordingly. Today heavy additional supply- and export lines are under construction, and the plant is extended more than ever. The main role of the factory is to separate the raw gas into commercial products and to pump or ship it to the markets. The site covers a large number of well-known mechanical equipment. This presentation deals with piping, mechanical and structural disciplines. The lifetime of mechanical equipment is often difficult to predict as it depends on many factors, and the subject is complex. Mechanical equipment has been kept in-house, which provides detailed knowledge of the stages from a new to a 14 years old plant. The production regularity has always been very high, as required. The standard of the equipment is well kept, support systems are efficient, and human improvisation is extremely valuable.

  7. An experimental study of the mechanism of failure of rocks under borehole jack loading

    Science.gov (United States)

    Van, T. K.; Goodman, R. E.

    1971-01-01

    Laboratory and field tests with an experimental jack and an NX-borehole jack are reported. The following conclusions were made: Under borehole jack loading, a circular opening in a brittle solid fails by tensile fracturing when the bearing plate width is not too small. Two proposed contact stress distributions can explain the mechanism of tensile fracturing. The contact stress distribution factor is a material property which can be determined experimentally. The borehole tensile strength is larger than the rupture flexural strength. Knowing the magnitude and orientation of the in situ stress field, borehole jack test results can be used to determine the borehole tensile strength. Knowing the orientation of the in situ stress field and the flexural strength of the rock substance, the magnitude of the in situ stress components can be calculated. The detection of very small cracks is essential for the accurate determination of the failure loads which are used in the calculation of strengths and stress components.

  8. Mechanical (turbines and auxiliary equipment)

    CERN Document Server

    Sherry, A; Cruddace, AE

    2013-01-01

    Modern Power Station Practice, Volume 3: Mechanical (Turbines and Auxiliary Equipment) focuses on the development of turbines and auxiliary equipment used in power stations in Great Britain. Topics covered include thermodynamics and steam turbine theory; turbine auxiliary systems such as lubrication systems, feed water heating systems, and the condenser and cooling water plants. Miscellaneous station services, and pipework in power plants are also described. This book is comprised of five chapters and begins with an overview of thermodynamics and steam turbine theory, paying particular attenti

  9. Kinetics and mechanism of jack bean urease inhibition by Hg2+

    Directory of Open Access Journals (Sweden)

    Du Nana

    2012-12-01

    Full Text Available Abstract Background Jack bean urease (EC 3.5.1.5 is a metalloenzyme, which catalyzes the hydrolysis of urea to produce ammonia and carbon dioxide. The heavy metal ions are common inhibitors to control the rate of the enzymatic urea hydrolysis, which take the Hg2+ as the representative. Hg2+ affects the enzyme activity causing loss of the biological function of the enzyme, which threatens the survival of many microorganism and plants. However, inhibitory kinetics of urease by the low concentration Hg2+ has not been explored fully. In this study, the inhibitory effect of the low concentration Hg2+ on jack bean urease was investigated in order to elucidate the mechanism of Hg2+ inhibition. Results According to the kinetic parameters for the enzyme obtained from Lineweaver–Burk plot, it is shown that the Km is equal to 4.6±0.3 mM and Vm is equal to 29.8±1.7 μmol NH3/min mg. The results show that the inhibition of jack bean urease by Hg2+ at low concentration is a reversible reaction. Equilibrium constants have been determined for Hg2+ binding with the enzyme or the enzyme-substrate complexes (Ki =0.012 μM. The results show that the Hg2+ is a noncompetitive inhibitor. In addition, the kinetics of enzyme inhibition by the low concentration Hg2+ has been studied using the kinetic method of the substrate reaction. The results suggest that the enzyme first reversibly and quickly binds Hg2+ and then undergoes a slow reversible course to inactivation. Furthermore, the rate constant of the forward reactions (k+0 is much larger than the rate constant of the reverse reactions (k-0. By combining with the fact that the enzyme activity is almost completely lost at high concentration, the enzyme is completely inactivated when the Hg2+ concentration is high enough. Conclusions These results suggest that Hg2+ has great impacts on the urease activity and the established inhibition kinetics model is suitable.

  10. Kinetics and Mechanism Study of Competitive Inhibition of Jack-Bean Urease by Baicalin

    Science.gov (United States)

    Tan, Lirong; Su, Jiyan; Wu, Dianwei; Yu, Xiaodan; Su, Zuqing; Wu, Xiaoli; Kong, Songzhi; Lai, Xiaoping; Lin, Ji; Su, Ziren

    2013-01-01

    Baicalin (BA) is the principal component of Radix Scutellariae responsible for its pharmacological activity. In this study, kinetics and mechanism of inhibition by BA against jack-bean urease were investigated for its therapeutic potential. It was revealed that the IC50 of BA against jack-bean urease was 2.74 ± 0.51 mM, which was proved to be a competitive and concentration-dependent inhibition with slow-binding progress curves. The rapid formation of initial BA-urease complex with an inhibition constant of K i = 3.89 × 10−3 mM was followed by a slow isomerization into the final complex with an overall inhibition constant of K i* = 1.47 × 10−4 mM. High effectiveness of thiol protectors against BA inhibition indicated that the strategic role of the active-site sulfhydryl group of the urease was involved in the blocking process. Moreover, the inhibition of BA was proved to be reversible due to the fact that urease could be reactivated by dithiothreitol but not reactant dilution. Molecular docking assay suggested that BA made contacts with the important activating sulfhydryl group Cys-592 residues and restricted the mobility of the active-site flap. Taken together, it could be deduced that BA was a competitive inhibitor targeting thiol groups of urease in a slow-binding manner both reversibly and concentration-dependently, serving as a promising urease inhibitor for treatments on urease-related diseases. PMID:24198731

  11. Epiberberine, a natural protoberberine alkaloid, inhibits urease of Helicobacter pylori and jack bean: Susceptibility and mechanism.

    Science.gov (United States)

    Tan, Lihua; Li, Cailan; Chen, Hanbin; Mo, Zhizhun; Zhou, Jiangtao; Liu, Yuhong; Ma, Zhilin; Xu, Yuyao; Yang, Xiaobo; Xie, Jianhui; Su, Ziren

    2017-12-15

    In our previous study, Rhizoma Coptidis extract was found to exert more potent inhibitory effect than its major component berberine towards urease from Helicobacter pylori (HPU) and jack bean (JBU). In continuation of our work, the present study was designed to further comparatively investigate the urease inhibitory activities of five major protoberberine alkaloids in Rhizoma Coptidis, namely berberine, palmatine, coptisine, epiberberine, jateorhizine to identify the bioactive constituent, and illuminate the potential mechanism of action. Results indicated that the five protoberberine alkaloids acted as concentration-dependent inactivators of urease with IC 50 values ranging between 3.0 and 5087μM for HPU and 2.3->10,000μM for JBU, respectively. Notably, epiberberine (EB) was found to be the most potent inhibitor against both ureases with IC 50 values of 3.0±0.01μM for HPU and 2.3±0.01μM for JBU, which was more effective than the standard urease inhibitor, acetohydroxamic acid (83±0.01μM for HPU and 22±0.01μM for JBU, respectively). Further kinetic analysis revealed that the type of EB inhibition against HPU was slow-binding and uncompetitive, with K i of 10.6±0.01μM, while slow-binding and competitive against JBU with K i of 4.6±0.01μM. Addition of thiol reagents, such as l-cysteine, glutathione and dithiothreitol, significantly abolished the inhibition, while Ni 2+ competitive inhibitors, boric acid and sodium fluoride, synergetically inhibited urease with EB, indicating the obligatory role of the active site sulfhydryl group for the inhibition. In addition, binding of EB with the urease proved to be reversible, as about 65% and 90% enzymatic activity of HPU and JBU, respectively, could be restored by dithiothreitol application. These findings highlighted the potential role of Rhizoma Coptidis protoberberine alkaloids, especially EB, as a lead urease inhibitor in the treatment of diseases associated with ureolytic bacteria. Thus, EB had good

  12. Mechanical equipment for magnet measurement and alignment

    International Nuclear Information System (INIS)

    Harvey, A.

    1992-05-01

    The mechanical equipment for measuring and aligning (or fiducializing) magnets is described by reference to devices designed and built by a number of laboratories. Some of these are now available commercially. The descriptions are supplemented by a list of representative sources of hardware

  13. 29 CFR 1926.952 - Mechanical equipment.

    Science.gov (United States)

    2010-07-01

    ... equipment that are not covered with insulating protective equipment. (c) Derrick trucks, cranes and other lifting equipment. (1) All derrick trucks, cranes and other lifting equipment shall comply with subpart N...

  14. 21 CFR 211.68 - Automatic, mechanical, and electronic equipment.

    Science.gov (United States)

    2010-04-01

    ... SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Equipment § 211.68 Automatic, mechanical, and electronic equipment. (a) Automatic, mechanical, or electronic... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Automatic, mechanical, and electronic equipment...

  15. The Alignment Jacks of the LHC Cryomagnets

    CERN Document Server

    Dwivedi, J; Goswami, S G; Madhumurthy, V; Parma, V; Soni, H C

    2004-01-01

    The precise alignment of the 1232 dipoles, 474 Short Straight Sections (SSS) and some other components of the LHC collider, requires the use of 6800 jacks. The specific requirements and the need for a cost-effective solution for this large production, justified the development and industrialisation of a dedicated mechanical jack. The jack was developed, and is now being produced by Centre for Advanced Technology, India, in the framework of a collaboration between CERN and the Department of Atomic Energy in India. Three jacks support each of the 32-ton heavy, 15-meter long cryo-dipole of LHC, and provide the required alignment features. Identical jacks support the lighter LHC Short Straight Sections. Presently, the mass production of 6800 jacks is in progress with two Indian manufacturers, and 3545 jacks have already been delivered to CERN by April 2004. Considering the successful performance of the jacks, it is now envisaged to extend their use, with some modifications, for even higher-demanding alignment of ...

  16. Discussion on the safety classification of nuclear safety mechanical equipment

    International Nuclear Information System (INIS)

    Shen Wei

    2010-01-01

    The purpose and definition of the equipment safety classification in nuclear plant are introduced. The differences of several safety classification criterions are compared, and the object of safety classification is determined. According to the regulation, the definition and category of the safety functions are represented. The safety classification method, safety classification process, safety class interface, and the requirement for the safety class mechanical equipment are explored. At last, the relation of the safety classification between the mechanical and electrical equipment is presented, and the relation of the safety classification between mechanical equipment and system is also presented. (author)

  17. Environmental/dynamic mechanical equipment qualification and dynamic electrical equipment qualification program (EDQP)

    International Nuclear Information System (INIS)

    Hunter, J.A.

    1984-01-01

    Equipment qualification research is being conducted to investigate acceptable criteria, requirements, and methodologies for the dynamic (including seismic) and environmental qualification of mechanical equipment and for the dynamic (including seismic) qualification of electrical equipment. The program is organized into three elements: (1) General Research, (2) Environmental Research, and (3) Dynamic Research. This paper presents the highlights of the results to date in these three elements of the program

  18. Jack superpolynomials: physical and combinatorial definitions

    International Nuclear Information System (INIS)

    Desrosiers, P.; Mathieu, P.; Lapointe, L.

    2004-01-01

    Jack superpolynomials are eigenfunctions of the supersymmetric extension of the quantum trigonometric Calogero-Moser-Sutherland Hamiltonian. They are orthogonal with respect to the scalar product, dubbed physical, that is naturally induced by this quantum-mechanical problem. But Jack superpolynomials can also be defined more combinatorially, starting from the multiplicative bases of symmetric superpolynomials, enforcing orthogonality with respect to a one-parameter deformation of the combinatorial scalar product. Both constructions turn out to be equivalent. (author)

  19. Jack St. Clair Kilby

    Indian Academy of Sciences (India)

    IAS Admin

    the modern history of science and technology is highlighted by the fact that Jack ... Missouri, a traditional mid-western state in the United States of. America. ... his engineering education got interrupted when the second world war intensified ...

  20. 'Weightless' acrylic painting by Jack Kroehnke

    Science.gov (United States)

    1987-01-01

    'Weightless' acrylic painting by Jack Kroehnke depicts STS-26 Discovery, Orbiter Vehicle (OV) 103, Mission Specialist (MS) David C. Hilmers participating in extravehicular activity (EVA) simulation in JSC Weightless Environment Training Facility (WETF) Bldg 29. In the payload bay (PLB) mockup, Hilmers, wearing extravehicular mobility unit (EMU), holds onto the mission-peculiar equipment support structure in foreground while SCUBA-equipped diver monitors activity overhead and camera operator records EVA procedures. Copyrighted art work for use by NASA.

  1. Automatic Hydraulic Jack Inbuilt In A Four Wheeler

    Directory of Open Access Journals (Sweden)

    Parth M. Patel

    2015-08-01

    Full Text Available With increasing levels of technology efforts being put to increase the comfort and safety. These can be done by implementation of better design. This paper describes Implementation of Automatic hydraulic jack Mechanism in a four wheeler itself. The jack will be powered by the battery. So at a time of puncture to replace the wheel one has to just press the button and the jack which is fitted in the car itself will lift the car.

  2. Effects of Defatted Jack Bean Flour and Jack Bean Protein ...

    African Journals Online (AJOL)

    This study evaluated the effects of substituting wheat flour with defatted Jack bean flour and Jack bean protein concentrate on bread quality. Jack bean flour milled from the seed nibs was defatted with n-hexane and part of the defatted flour (DJF) extracted in acid medium (pH; 4.5) for protein concentrate (JPC). Both the DJF ...

  3. Collaboration Mechanism for Equipment Instruction of Multiple Energy Systems

    Science.gov (United States)

    Wang, Dong; Wang, Tuo; Wang, Qi; Zhang, Zhao; Zhao, Mingyu; Wang, Yinghui

    2018-01-01

    When multiple energy systems execute optimization instructions simultaneously, and the same equipment is Shared, the instruction conflict may occur. Aiming at the above problems, taking into account the control objectives of each system, the characteristics of different systems, such as comprehensive clean energy, energy efficiency, and peak filling, etc., designed the instruction coordination mechanism for the daemon. This mechanism mainly acts on the main station of the system, and form a final optimization instruction. For some specific scenarios, the collaboration mechanism of unlocking the terminal is supplemented. The mechanism determines the specific execution instructions based on the arrival time of the instruction. Finally, the experiment in Tianjin eco-city shows that this algorithm can meet the instruction and collaboration requirements of multi-energy systems, and ensure the safe operation of the equipment.

  4. Sennar Jacks (Equus asinus)

    African Journals Online (AJOL)

    This study was carried out with an objective of evaluating the breeding soundness and sexual behavior of Sennar jackasses. ... score of 7 for the breeding and 4.8 for the working jacks. The mean (iSE) of height at wither,the ..... Equine Reproductive Physiology, Breeding and Stud Manage- ment, 2ndEdn. Farming Press ...

  5. Sulfonamide-Linked Ciprofloxacin, Sulfadiazine and Amantadine Derivatives as a Novel Class of Inhibitors of Jack Bean Urease; Synthesis, Kinetic Mechanism and Molecular Docking.

    Science.gov (United States)

    Channar, Pervaiz Ali; Saeed, Aamer; Albericio, Fernando; Larik, Fayaz Ali; Abbas, Qamar; Hassan, Mubashir; Raza, Hussain; Seo, Sung-Yum

    2017-08-16

    Sulfonamide derivatives serve as an important building blocks in the drug design discovery and development (4D) process. Ciprofloxacin-, sulfadiazine- and amantadine-based sulfonamides were synthesized as potent inhibitors of jack bean urease and free radical scavengers. Molecular diversity was explored and electronic factors were also examined. All 24 synthesized compounds exhibited excellent potential against urease enzyme. Compound 3e (IC 50 = 0.081 ± 0.003 µM), 6a (IC 50 = 0.0022 ± 0.0002 µM), 9e (IC 50 = 0.0250 ± 0.0007 µM) and 12d (IC 50 = 0.0266 ± 0.0021 µM) were found to be the lead compounds compared to standard (thiourea, IC 50 = 17.814 ± 0.096 µM). Molecular docking studies were performed to delineate the binding affinity of the molecules and a kinetic mechanism of enzyme inhibition was propounded. Compounds 3e , 6a and 12d exhibited a mixed type of inhibition, while derivative 9e revealed a non-competitive mode of inhibition. Compounds 12a , 12b , 12d , 12e and 12f showed excellent radical scavenging potency in comparison to the reference drug vitamin C.

  6. Jack Michael's Motivation

    OpenAIRE

    Miguel, Caio F.

    2013-01-01

    Among many of Jack Michael's contributions to the field of behavior analysis is his behavioral account of motivation. This paper focuses on the concept of motivating operation (MO) by outlining its development from Skinner's (1938) notion of drive. Conceptually, Michael's term helped us change our focus on how to study motivation by shifting its origins from the organism to the environment. Michael's account also served to stimulate applied research and to better understand behavioral functio...

  7. Happy birthday, Jack Steinberger

    CERN Multimedia

    CERN Bulletin

    2016-01-01

    Even if he’s recently stopped coming to CERN on his bike, Jack Steinberger and his piercing blue eyes are still regular visitors to our corridors. As he celebrates his 95th birthday, we pay tribute to one of CERN’s greatest scientists.   Jack Steinberger in 2008, pictured on the occasion of the "Accelerating Nobel" exhibition. (Image: Claudia Marcelloni/CERN) Jack emigrated from Germany to the United States in 1934 to escape the persecution of the Jews. He later went on to study under Enrico Fermi in Chicago and in the 1950s, he contributed to the development of bubble chambers. Using this new detection apparatus, he was involved in the myriad discoveries and results that led to the construction of the Standard Model. In 1961, while at Columbia University (New York), he took part in the first experiment with a high-energy neutrino beam, which gave rise to the discovery of the muon neutrino. This discovery was awarded the&a...

  8. Jack Reeves and his science.

    Science.gov (United States)

    Moore, Lorna G; Grover, Robert F

    2006-04-28

    John T. (Jack) Reeves' science is reviewed across the 37 years of his research career at the University of Colorado Health Sciences Center, a period which occupied approximately half his remarkable life. His contributions centered on understanding the inter-relatedness as well as the underlying mechanisms controlling the various components of the O(2) transport system. We review here his studies on exercise performance; these encompassed about half his scientific output with the other half being devoted to the study of hypoxic pulmonary hypertension. Early studies concerned cardiac output, showing how it was a balance between O(2) uptake and O(2) extraction, and that cardiac output during exercise at high altitude was reduced, most likely because of decreased plasma volume and left ventricular filling. Jack's many studies addressed virtually every aspect of the O(2) transport system -- adding significantly to our understanding of the syndromes of altitude illness, the mechanisms by which ventilatory sensitivity to hypoxia and hypercapnia influenced ventilatory acclimatization, and the contributions of the various limbs of the autonomic nervous system on systemic blood pressure, vascular resistance and substrate utilization. His scientific career ended abruptly in 2004 when struck by a car while biking to work, but his legacy remains in his more than 385+ research articles or chapters, the 40+ fellows he trained, and the countless number of younger (and older) scientists for whom he served as a role model for learning how to scrutinize their data and present their findings in clear and sometimes bold prose. An integral man, he is sorely missed.

  9. PRECISION MOTION SYSTEM FOR OPTO-MECHANICAL EQUIPMENT OF MICROELECTRONICS

    Directory of Open Access Journals (Sweden)

    I. V. Dainiak

    2015-01-01

    Full Text Available The paper proposes a structure of precision motion system built on the basis of a circular multi-coordinate synchronous segment motor and reconfigurable parallel kinematic mechanism. The multi-coordinate synchronous segment motor may have from two to six movable segments depending on the design, and number of the segments generally defines an internal mobility of the motor. A specific feature of the parallel kinematic mechanism consists in the possibility of its structure reconfiguration by serial connection of two neighboring rods with the help of free elements of their spherical joints into triangular circuits with one spherical hinge at the common vertex. As result of this, the controlled motion of motor movable segments is transformed into the complex spatial displacement of circular platform with number of degrees of freedom up to six inclusively.A mathematical model for solution of the kinematic problem in the investigated parallel mechanism has been offered in the paper. The model allows to calculate a position of movable segments of multi-coordinate synchronous motor depending on the desired position and orientation of the executive circular platform. The parametric definition of base point positions in the motor segments in time allows eventually to form algorithms of programmable motions.The paper substantiates ability to embed the developed motion system into projection unit of opto-mechanical equipment while preserving traditional configuration scheme. This provides the possibility of adaptive adjustment of optical elements during operation; it allows to adjust the optical elements when the geometry of projection system is changed due to deterioration. As result, main characteristics of projection system: resolution, depth of field and image contrast and distortion are maintained at the required level. The developed motion system can be used as a coordinate system of positioning, alignment and scanning in the assembly and other

  10. From Jack to Double Jack Polynomials via the Supersymmetric Bridge

    Science.gov (United States)

    Lapointe, Luc; Mathieu, Pierre

    2015-07-01

    The Calogero-Sutherland model occurs in a large number of physical contexts, either directly or via its eigenfunctions, the Jack polynomials. The supersymmetric counterpart of this model, although much less ubiquitous, has an equally rich structure. In particular, its eigenfunctions, the Jack superpolynomials, appear to share the very same remarkable combinatorial and structural properties as their non-supersymmetric version. These super-functions are parametrized by superpartitions with fixed bosonic and fermionic degrees. Now, a truly amazing feature pops out when the fermionic degree is sufficiently large: the Jack superpolynomials stabilize and factorize. Their stability is with respect to their expansion in terms of an elementary basis where, in the stable sector, the expansion coefficients become independent of the fermionic degree. Their factorization is seen when the fermionic variables are stripped off in a suitable way which results in a product of two ordinary Jack polynomials (somewhat modified by plethystic transformations), dubbed the double Jack polynomials. Here, in addition to spelling out these results, which were first obtained in the context of Macdonal superpolynomials, we provide a heuristic derivation of the Jack superpolynomial case by performing simple manipulations on the supersymmetric eigen-operators, rendering them independent of the number of particles and of the fermionic degree. In addition, we work out the expression of the Hamiltonian which characterizes the double Jacks. This Hamiltonian, which defines a new integrable system, involves not only the expected Calogero-Sutherland pieces but also combinations of the generators of an underlying affine {widehat{sl}_2} algebra.

  11. Harvest of table olives by mechanical harvesting equipment

    Directory of Open Access Journals (Sweden)

    Filippo Gambella

    2013-09-01

    Full Text Available In this work, we have evaluated the performance, of an electric comb equipped with five undulated fingers used for mechanized the harvesting of table olives. The first aim of the work was to test three different types of coating materials used for covering the fingers: Silicon (S, Vulcanized rubber (VR and Natural rubber (NR. The diameter of the coating materials tested were 7mm (D1, 14 mm (D2, 19 mm (D3 in order to evaluate the damage of different working conditions on the intact olives. During harvesting, silicon at 7mm and 14mm resulted in the largest percentage of undamaged the fruit (67% and 65%, natural rubber 63% and vulcanized rubber at the 54%. The second aim was to evaluate the combination, in terms of the best performance, of the machines used for mechanized harvesting of table olives. Several factors have been examined: undulating fingers variation thickness, different rotational speeds and different coating materials used to reduce the impact damage on olives. From the tests on olive tree we have determined that while plastic materials (S and (NR appear to have a positive role in harvest quality, the vibration transmitted to the operator’s hand is great from 6.48 m/s2 for S to 6.31 m/ s2 for NR and 2.92 m/s2 for VR, respect to the materials used.

  12. Jacks--A Study of Simple Machines.

    Science.gov (United States)

    Parsons, Ralph

    This vocational physics individualized student instructional module on jacks (simple machines used to lift heavy objects) contains student prerequisites and objectives, an introduction, and sections on the ratchet bumper jack, the hydraulic jack, the screw jack, and load limitations. Designed with a laboratory orientation, each section consists of…

  13. 49 CFR 176.905 - Motor vehicles or mechanical equipment powered by internal combustion engines.

    Science.gov (United States)

    2010-10-01

    ... of ignition. A motor vehicle or mechanical equipment showing any signs of leakage or electrical fault... equipment is stowed. (f) Each hold or compartment must be ventilated and fitted with an overhead water... smoke or fire detection system capable of alerting personnel on the bridge. (h) All electrical equipment...

  14. 49 CFR 173.220 - Internal combustion engines, self-propelled vehicles, mechanical equipment containing internal...

    Science.gov (United States)

    2010-10-01

    ... and vehicles with certain electronic equipment when transported by aircraft or vessel. When an... vehicles, mechanical equipment containing internal combustion engines, and battery powered vehicles or... Than Class 1 and Class 7 § 173.220 Internal combustion engines, self-propelled vehicles, mechanical...

  15. Jack Stenner: The Lexile King.

    Science.gov (United States)

    Webster, Linda J.

    2000-01-01

    Traces the career of Jack Stenner. Stenner made the empirical discovery that observable readability could be entirely predicted from word familiarity and sentence length, and applied this "Lexile Framework"(R) to books and readers. Discusses the use of the Lexile Framework as a way to target specific readers. (SLD)

  16. Stress analysis of jacks, frame and bearing connections, and drill rod for core sampler truck No. 2

    International Nuclear Information System (INIS)

    Ziada, H.H.

    1995-01-01

    This analysis evaluates the structural design adequacy of several components and connections for the rotary mode core sampler truck (RMCST) No. 2. This analysis was requested by the Characterization Equipment Group (WHC 1994a). The components addressed in this report are listed below: front jack assembly and connection to the truck chassis; rear jack assembly and connection to the truck chassis; center outrigger jacks and connection to the truck chassis; lower frame assembly and connection to the truck chassis; bolt connections for bearing plate assembly (for path of maximum load); traverse slide brackets and mounting of the traverse jack cylinders; and drill rod (failure loads)

  17. Limited usage of mechanical equipment in small-scale rice farming: a cause for concern

    Directory of Open Access Journals (Sweden)

    Gaudiose Mujawamariya

    2017-06-01

    Full Text Available The role of mechanization in agriculture is well documented in terms of improving productivity of farm labour and land and sustaining income status and welfare of small-scale farmers. In rice production, there is a high cost associated with labour intensive production practices especially in land preparation, weeding and harvesting, the limited adoption of mechanical equipment in these operations remains an issue of concern. The current study investigates the usage of mechanical equipment in a setting where majority of farmers are exposed to technologies but cases of non-usage/adoption are observed. The choice of usage of mechanical equipment is analysed through probit and poisson models. Mechanization generally has a positive effect on production. However, the cost associated with its usage high. The equipment should be made available and affordable to farmers especially because demand for rent is not met. Awareness is essential for adoption and ease of use of mechanization.

  18. JACK - ANTHROPOMETRIC MODELING SYSTEM FOR SILICON GRAPHICS WORKSTATIONS

    Science.gov (United States)

    Smith, B.

    1994-01-01

    JACK is an interactive graphics program developed at the University of Pennsylvania that displays and manipulates articulated geometric figures. JACK is typically used to observe how a human mannequin interacts with its environment and what effects body types will have upon the performance of a task in a simulated environment. Any environment can be created, and any number of mannequins can be placed anywhere in that environment. JACK includes facilities to construct limited geometric objects, position figures, perform a variety of analyses on the figures, describe the motion of the figures and specify lighting and surface property information for rendering high quality images. JACK is supplied with a variety of body types pre-defined and known to the system. There are both male and female bodies, ranging from the 5th to the 95th percentile, based on NASA Standard 3000. Each mannequin is fully articulated and reflects the joint limitations of a normal human. JACK is an editor for manipulating previously defined objects known as "Peabody" objects. Used to describe the figures as well as the internal data structure for representing them, Peabody is a language with a powerful and flexible mechanism for representing connectivity between objects, both the joints between individual segments within a figure and arbitrary connections between different figures. Peabody objects are generally comprised of several individual figures, each one a collection of segments. Each segment has a geometry represented by PSURF files that consist of polygons or curved surface patches. Although JACK does not have the capability to create new objects, objects may be created by other geometric modeling programs and then translated into the PSURF format. Environment files are a collection of figures and attributes that may be dynamically moved under the control of an animation file. The animation facilities allow the user to create a sequence of commands that duplicate the movements of a

  19. Research on the energy and ecological efficiency of mechanical equipment remanufacturing systems

    Science.gov (United States)

    Shi, Junli; Cheng, Jinshi; Ma, Qinyi; Wang, Yajun

    2017-08-01

    According to the characteristics of mechanical equipment remanufacturing system, the dynamic performance of energy consumption and emission is explored, the equipment energy efficiency and emission analysis model is established firstly, and then energy and ecological efficiency analysis method of the remanufacturing system is put forward, at last, the energy and ecological efficiency of WD615.87 automotive diesel engine remanufacturing system as an example is analyzed, the way of energy efficiency improvementnt and environmental friendly mechanism of remanufacturing process is put forward.

  20. Versatile equipment for mechanical testing of active materials

    International Nuclear Information System (INIS)

    Bertsch, Johannes; Heimgartner, Peter

    2005-01-01

    At the Paul Scherrer Institute (PSI) 3 different project groups presently perform aging research on active materials. The research fields are fusion, high neutron flux targets and LWR relevant components. Up to now mechanical testing has been performed with small, low dose rate samples behind local shielding, not appropriate for highly activated material. To overcome this situation, a cell concept for active mechanical testing was elaborated and has been erected in PSI's Hotlab. It consists of 4 shielded cells. 3 connected cells are versatile and independently operable for highly beta/gamma active samples. One cell is an alpha/beta/gamma-box which will be realized in a second phase. This paper presents the versatility especially of the beta/gamma-cells: The different user groups perform experiments in these cells, whereas different machines can be placed into the cells. As consequence of the need of heavily shielded cell doors, a special strengthening and levelling of the floor has been required. In all cells the relevant media are installed. Besides the performance of the cells, the project progress as the difficulties and their solutions are described. (Author)

  1. John B. "Jack" Townshend (1927-2012)

    Science.gov (United States)

    Love, Jeffrey J.; Finn, Carol A.

    2012-01-01

    Jack Townshend, geophysicist and dedicated public servant, died on 13 August 2012 in Fairbanks, Alaska. He was 85. Jack's career with the federal government, most of it with the national magnetic observatory program, spanned more than six solar cycles of time, and he retired only days before his death. The duration of Jack's career encompassed an important period in the history of the advancement of our understanding of the Earth. Jack's career of contributions, his life, and his personality are worthy of retrospective celebration.

  2. Teacher-Perceived Adequacy of Tools and Equipment Available to Teach Agricultural Mechanics

    Science.gov (United States)

    McCubbins, O. P.; Anderson, Ryan G.; Paulsen, Thomas H.; Wells, Trent

    2016-01-01

    Agricultural mechanics is an important component of a well-rounded school-based agricultural education (SBAE) program. Within agricultural mechanics courses lies a plethora of topics and skills to be covered. Adequate tools and equipment are vital in preparing students to fill an expanding, 21st century workforce. The issue of inadequate teaching…

  3. 21 CFR 111.30 - What requirements apply to automated, mechanical, or electronic equipment?

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false What requirements apply to automated, mechanical, or electronic equipment? 111.30 Section 111.30 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION CURRENT GOOD MANUFACTURING...

  4. [A young child with respiratory acidosis and hypoxia from mechanical ventilation with equipment made for adults].

    Science.gov (United States)

    Joor, Fleur; Markhorst, Dick G; Kneyber, Martin C J; van Heerde, Marc

    2011-01-01

    During mechanical ventilation of young children, problems may arise due to the additional dead space of the ventilation circuit. This may lead to respiratory acidosis and even hypoxia in the child. A 3-month-old boy suffered from frequent apnoea. He was mechanically ventilated for this. Shortly after its initiation, he developed severe respiratory acidosis, hypoxemia and circulatory insufficiency. This was due to a large additional dead space caused by the use of equipment components made for adults. After he was switched to a circuit suitable for himself, he recovered rapidly. As a rule of thumb, an additional dead space of 1.5-2 ml/kg body weight is acceptable in young children. Emergency wards for young children should have specific equipment to mechanically ventilate them, and have a protocol paying explicit attention to the dead space.

  5. Topological color codes on Union Jack lattices: a stable implementation of the whole Clifford group

    International Nuclear Information System (INIS)

    Katzgraber, Helmut G.; Bombin, H.; Andrist, Ruben S.; Martin-Delgado, M. A.

    2010-01-01

    We study the error threshold of topological color codes on Union Jack lattices that allow for the full implementation of the whole Clifford group of quantum gates. After mapping the error-correction process onto a statistical mechanical random three-body Ising model on a Union Jack lattice, we compute its phase diagram in the temperature-disorder plane using Monte Carlo simulations. Surprisingly, topological color codes on Union Jack lattices have a similar error stability to color codes on triangular lattices, as well as to the Kitaev toric code. The enhanced computational capabilities of the topological color codes on Union Jack lattices with respect to triangular lattices and the toric code combined with the inherent robustness of this implementation show good prospects for future stable quantum computer implementations.

  6. Research program for seismic qualification of nuclear plant electrical and mechanical equipment. Task 3. Recommendations for improvement of equipment qualification methodology and criteria. Volume 3

    International Nuclear Information System (INIS)

    Kana, D.D.; Pomerening, D.J.

    1984-08-01

    The Research Program for Seismic Qualification of Nuclear Plant Electrical and Mechanical Equipment has spanned a period of three years and resulted in seven technical summary reports, each of which covered in detail the findings of different tasks and subtasks, and have been combined into five NUREG/CR volumes. Volume 3 presents recommendations for improvement of equipment qualification methodology and procedural clarification/modification. The fifth category identifies issues where adequate information does not exist to allow a recommendation to be made

  7. Research program for seismic qualification of nuclear plant electrical and mechanical equipment. Task 4. Use of fragility in seismic design of nuclear plant equipment. Volume 4

    International Nuclear Information System (INIS)

    Kana, D.D.; Pomerening, D.J.

    1984-08-01

    The Research Program for Seismic Qualification of Nuclear Plant Electrical and Mechanical Equipment has spanned a period of three years and resulted in seven technical summary reports, each of which have covered in detail the findings of different tasks and subtasks, and have been combined into five NUREG/CR volumes. Volume 4 presents study of the use of fragility concepts in the design of nuclear plant equipment and compares the results of state-of-the-art proof testing with fragility testing

  8. Market Competitiveness Evaluation of Mechanical Equipment with a Pairwise Comparisons Hierarchical Model.

    Science.gov (United States)

    Hou, Fujun

    2016-01-01

    This paper provides a description of how market competitiveness evaluations concerning mechanical equipment can be made in the context of multi-criteria decision environments. It is assumed that, when we are evaluating the market competitiveness, there are limited number of candidates with some required qualifications, and the alternatives will be pairwise compared on a ratio scale. The qualifications are depicted as criteria in hierarchical structure. A hierarchical decision model called PCbHDM was used in this study based on an analysis of its desirable traits. Illustration and comparison shows that the PCbHDM provides a convenient and effective tool for evaluating the market competitiveness of mechanical equipment. The researchers and practitioners might use findings of this paper in application of PCbHDM.

  9. Search for the optimal size of printed circuit boards for mechanical structures for electronic equipment

    Directory of Open Access Journals (Sweden)

    Yefimenko A. A.

    2014-12-01

    Full Text Available The authors present a method, an algorithm and a program, designed to determine the optimal size of printed circuit boards (PCB of mechanical structures and different kinds of electronic equipment. The PCB filling factor is taken as an optimization criterion. The method allows one to quickly determine the dependence of the filling factor on the size of the PCB for various components.

  10. A mechanical design for positioning of gm detector for system of avian flu virus detection equipment

    International Nuclear Information System (INIS)

    Rahmat; Budi Santoso; Krismawan; Abdul Jalil

    2010-01-01

    Mechanical design for positioning of GM detector system has been done. It is used for avian flu detection equipment. The requirements for the design are to protect detection system against shock, portable, and easy to maintain. The mechanical system consists of connectors, cable assemblies, holders, casing, housing and detectors cover. The selected material should have small gamma radiation absorption property in order to give optimum counts for the detector. The design result should give a system that is easy to operate, cheap and easy to assemble. (author)

  11. Mechanical design for positioning of GM detector for system of avian flu virus detection equipment

    International Nuclear Information System (INIS)

    Rahmat; Budi Santoso; Krismawan; Abdul Jalil

    2010-01-01

    Mechanical design for positioning of GM detector system has been done. It is used for avian flu detection equipment. The requirements for the design are to protect detection system against shock, portable, and easy to maintain. The mechanical system consists of connectors, cable assemblies, holders, casing, housing and detectors cover. The selected material should have small gamma radiation absorption property in order to give optimum counts for the detector. The design result should give a system that is easy to operate, cheap and easy to assemble. (author)

  12. Loosening and damage mechanism of thread-joined structures in nuclear power equipment

    International Nuclear Information System (INIS)

    Tang Hui

    1999-01-01

    The author proposes a loosening mechanism of thread-joined structures under vibrate environments in the nuclear power equipment and structures, which is on the base of the macro and imperceptible-mechanics analysis. It has answered the problems on the seizing, the adhesive wearing, the generation of cracks, the thread-tooth fracture. So it has a conclusion that the loosening of thread-joined structures is essential trend, in other words, the locking property of thread-pair is failure under vibrate environments

  13. Cost determination of the electro-mechanical equipment of a small hydro-power plant

    Energy Technology Data Exchange (ETDEWEB)

    Ogayar, B.; Vidal, P.G. [Grupo de Investigacion IDEA, Escuela Politecnica Superior, University of Jaen, Campus de Las Lagunillas, s/n. 23071-Jaen (Spain)

    2009-01-15

    One of the most important elements on the recovery of a small hydro-power plant is the electro-mechanical equipment (turbine-alternator), since the cost of the equipment means a high percentage of the total budget of the plant. The present paper intends to develop a series of equations which determine its cost from basic parameters such as power and net head. These calculations are focused at a level of previous study, so it will be necessary to carry out the engineering project and request a budget to companies specialized on the construction of electro-mechanical equipment to know its cost more accurately. Although there is a great diversity in the typology of turbines and alternators, data from manufacturers which cover all the considered range have been used. The above equations have been developed for the most common of turbines: Pelton, Francis, Kaplan and semiKaplan for a power range below 2 MW. The obtained equations have been validated with data from real installations which have been subject to analysis by engineering companies working on the assembly and design of small plants. (author)

  14. Mechanized covering application in equipment surfaces; Aplicacao mecanizada de revestimento em superficies de equipamentos

    Energy Technology Data Exchange (ETDEWEB)

    Abreu, Billy A. de; Broering, Carlos E. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica

    2004-07-01

    Facing such challenges, the main objective of this work is to develop automated equipment and new welding procedures to be used to repair tank reservoirs operating in corrosive media. The equipment is expected to be applied directly in the maintenance of petrochemical plants. The project consists on a mechanical displacement device, able to move along a flexible rail, which can be fixed to a concave or convex surface and fitting itself to the geometry. A transversal arm gives it a second movement ability, allowing oscillatory displacements and the exact positioning of the pistol. As it is widely known, the automated welding process results in a considerably increase in productivity and quality, when comparing to the hand made process. Therefore, knowing the parameters involved and adjusted the welding variables to the best values, it is expected to achieve welding free of imperfections, inconsistencies and errors, and able to be repetitive. (author)

  15. Development of microstructure to optimise mechanical performance of power generation equipment

    International Nuclear Information System (INIS)

    Marshall, P.

    1986-11-01

    The factors responsible for the development of microstructure in CEGB construction ceramics and steels is assessed as a function of composition, thermomechanical treatment, thermal ageing and environmental degradation. The relationships between microstructure and mechanical properties (tensile, toughness, creep and fatigue) of relevance to structures operating in power generation equipment is then developed in quantitative terms. The conclusions from the assessment are as follows: 1 The relationship between microstructure and mechanical properties of construction ceramics and steels used in the power generation industry has been assessed. 2 Factors which significantly influence microstructure and thus mechanical properties are chemical composition, thermomechanical treatment, ageing and environmental degradation. The influence of such microstructural changes in tensile, toughness, fatigue and creep properties of ceramics and steels is assessed. 3 The benefits arising from an understanding of materials behaviour are discussed in terms of improved materials and the assessment of plant performance. (author)

  16. A preliminary design of mechanical device on industrial digital radiography equipment design

    International Nuclear Information System (INIS)

    Nur Khasan; Samuel Praptoyo

    2015-01-01

    A preliminary design of mechanical device on industrial digital radiography equipment has been done. this design is intended as a basis for the manufacture of complete facilities for the realization a prototype on industrial digital radiography equipment. the design and construction were carried out by paying attention to the general configuration of the basic design in which its mechanical design has several components with specific dimensions and heavy mass. this design consist of a main frame holder, flat panel detector support and hydraulic hand stacker for mounting the x-ray machine. this mechanical device design will then be fabricated to facilitate and assist work of digital radiographic retrieval. computer application programs sketch-up is used to draw this design and the analysis stress of autodesk inventor to analysis the strength construction design. the results of this design are the configuration drawing, sketch drawings of construction and the safety factor of construction design with a minimum value of 2.39 as well as a maximum value of 15 when to be simulated by the load 500 Kg which is 4 times of total workload. (author)

  17. Equivalent mechanical parameters of oscillating rotary motors used in transport equipment

    Directory of Open Access Journals (Sweden)

    A. Andziulis

    2006-12-01

    Full Text Available In various appliances and equipment of sundry transport means there is a lot of diverse mechanisms of periodical movement. So, the various piston or membrane pumps of fuel feeding and lubrication systems, circulation pumps, air and refrigerating coolant compressors, etc. are the typical examples of innovative and well promising application of the oscillating motors. In these cases the moving part of a motor can be directly connected to the working body of driven mechanism without the additional gears. Consequently, the drive can be simplified in design and improved in efficiency and reliability. Application of the oscillating rotary motors, if used in the aforesaid devices, strictly depends on specific properties of mechanical system of a motor aggregated with the driven mechanism and considered as the one-piece unit on the whole. So, this study analyses how the properties of mechanical system, comprised of two moving parts interconnected eccentrically or centrically, can be evaluated by the equivalent rotational inertia, equivalent mass and by equivalent mechanical power factor which, in turn, determine the operating characteristics and basic possibilities of the motor.

  18. Jack Michael's Motivation

    Science.gov (United States)

    Miguel, Caio F.

    2013-01-01

    Among many of Jack Michael's contributions to the field of behavior analysis is his behavioral account of motivation. This paper focuses on the concept of "motivating operation" (MO) by outlining its development from Skinner's (1938) notion of "drive." Conceptually, Michael's term helped us change our focus on…

  19. Jack in the Box, Unit 1A

    DEFF Research Database (Denmark)

    Gammelgaard Nielsen, Anders

    2011-01-01

    In the assignment known as ‘JACK- in-the-box’ the aim is to foster col- laborative situations through man- aging a complex architectural issue. The aim is to conduct an integrat- ed teaching course that extends from an introductory outline pro- cess through to the project devel- opment phase...

  20. Mathematical modelling of a Fin Ray type mechanism, used in the case of the wrist rehabilitation equipment

    Directory of Open Access Journals (Sweden)

    Filip Ovidiu

    2017-01-01

    Full Text Available The paper presents the mathematical modelling of some Fin Ray-type mechanism, destined for the wrist-rehabilitation equipment, its driving being made by a pneumatic muscle. The validity of the mathematical modelling of Fin Ray mechanism is verified by threedimensional mechanism made in Pro/Engineer.

  1. Applying the vantage PDMS to jack-up drilling ships

    Science.gov (United States)

    Yin, Peng; Chen, Yuan-Ming; Cui, Tong-Kai; Wang, Zi-Shen; Gong, Li-Jiang; Yu, Xiang-Fen

    2009-09-01

    The plant design management system (PDMS) is an integrated application which includes a database and is useful when designing complex 3-D industrial projects. It could be used to simplify the most difficult part of a subsea oil extraction project—detailed pipeline design. It could also be used to integrate the design of equipment, structures, HVAC, E-ways as well as the detailed designs of other specialists. This article mainly examines the applicability of the Vantage PDMS database to pipeline projects involving jack-up drilling ships. It discusses the catalogue (CATA) of the pipeline, the spec-world (SPWL) of the pipeline, the bolt tables (BLTA) and so on. This article explains the main methods for CATA construction as well as problem in the process of construction. In this article, the authors point out matters needing attention when using the Vantage PDMS database in the design process and discuss partial solutions to these questions.

  2. SPECIFIC DEGRADATION STRUCTURE FEATURES AND MECHANICAL PROPERTIES OF FURNACE AND HEAT POWER EQUIPMENT ELEMENTS AFTER LONG-TERM OPERATION

    Directory of Open Access Journals (Sweden)

    F. I. Panteleenko

    2012-01-01

    Full Text Available The paper presents results of investigations on structure and mechanical properties of technological equipment elements made of heat-resistant steels. A scale of chrome and molybdenum steel microstructure degradation based on evaluation of  coagulated carbide size and material mechanical properties (a point from 0-operation without time limits, up to 4-operation prohibition has been proposed in the paper. It has been  established that an analysis of  steel microstructure directly on equipment elements by means of a portable microscope is an efficient express method for evaluation of equipment condition and structures due to control of material structure degradation rate of a diagnosed object.

  3. Automation and mechanization of in-service inspection of selected equipment in FRG's nuclear power plants

    International Nuclear Information System (INIS)

    Metke, E.

    1988-01-01

    The procedures and equipment are described for the automation and mechanization of in-service inspection in nuclear power plants in the FRG, used by the KWU company. Checks of the pressure vessel are done by visual means using a colour tv camera, the method of eddy currents and the ultrasonic method. An analysis is made of the time schedule of ultrasonic inspections, and the central column manipulator is described which allows to check all internal regions of the pressure vessel. Attention is also devoted to other devices, e.g., those for prestressing shanks, cleaning shanks, cleaning thread apertures, etc. A combined probe using the ultrasonic method and the eddy current method serves the inspection of heat exchange tubes in the steam generator. For inspecting the primary circuit the KWU company uses devices for checking and working the inner surface of pipes. Briefly described are examples of using KWU equipment in nuclear power plants in CMEA countries. (Z.M.). 11 figs., 6 refs

  4. An Expert System for Supporting the Design and Selection of Mechanical Equipment for Recreational Crafts

    Directory of Open Access Journals (Sweden)

    T. Gonciarz

    2014-06-01

    Full Text Available Expert Systems can be defined as computer programs, whose main task is to simulate a human expert, usually in a narrow field of expertise. Expert Systems have experienced tremendous growth and popularity since their commercial introduction in the early 1970’s. Today, Expert Systems are used in business, science, engineering, manufacturing and other engineering applications such as planning, scheduling, diagnosing equipment failures and are used in almost every stage of the manufacturing process and also in medicine and many other fields. Expert Systems belong to the field of artificial intelligence. An intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for the solution. The purpose of this paper is to present an Expert System which assists with the design of yachts and supports the selection of mechanical equipment for yachts and includes knowledge in the field of yachting engineering. Using the presented Expert System reduces the time during the design and production preparation process.

  5. Designing electronic equipment on the basis of standard mechanical structures using internet re­sour­ces

    Directory of Open Access Journals (Sweden)

    Karlangach A. P.

    2016-12-01

    Full Text Available The author proposes a method to design electronic equipment based on functional-node design method that involves the use of 2D- and 3D- models mechanical structures for electronic equipment as a way to reduce development time and errors when creating design documentation for electronic equipment. At present, most areas of science and technology are computerized, more problems in designing electronic equipment are dealt with using computer-aided design (CAD and Computer-aided manufacturing (CAM to reduce the time required for development and manufacturing of electronic equipment. Development of design documentation also requires a more effective approach, because the less the time for development of the design documentation is, the faster the developed device will go into production. The aim of the study is to develop a method of designing electronic equipment using 2D and 3D models of standard mechanical structures for electronic equipment using Internet resources. Based on the presented methods is an example of designing a device from standard bearing structures. Compared with traditional technology, the method of designing electronic equipment using standard parts has the following advantages: - reduces time and improves quality of development through the use of existing design documentation; - accelerates the implementation and introducing into production processes; - increases unification of design solutions.

  6. Modeling of the Jacked Pile Static Load Test with PLAX 3D

    Directory of Open Access Journals (Sweden)

    Tautvydas Statkus

    2016-12-01

    Full Text Available In this article jacked pile installation technology and its current processes, altering the base physical and mechanical characteristics are discussed. For the jacked pile static load test simulation Plax 3D software was selected, the opportunities and developments were described. Model building, materials, models, model geometry, finite elements, boundary conditions and assumptions adopted in addressing problems described in detail. Three different tasks formulated and load-settlement dependence a comparison of the results with the experiment given. Conclusions are formulated according to the modeling results.

  7. Reproductive aspects of Jack mackerel Trachurus murphy

    Directory of Open Access Journals (Sweden)

    Ángel Perea

    2013-10-01

    Full Text Available The time series of monthly gonadosomatic index (GSI and biannual size at first maturity of Jack mackerel Trachurus murphyiNichols 1920 in Peru between 1967 and 2012 is analyzed and discussed. The annual and interannual variation of the reproductive cycle was determined. It is shown that in Peru T. murphyihas a single relatively extended spawning period with a maximum in November each year. It is also shown that for more than four decades T. murphyi has spawned regularly every year in Peruvian waters. The reproductive activity of T. murphyi has a greater variability off Peru and the spawning period has peaks of lesser magnitude but extend longer than observed in the spawning occurring off Chile. The analyses of the sizes at first maturity of Jack mackerel in Peruvian waters did not show significant changes throughout the entire period observed.

  8. Experience of Implementing a Distributed Control System for Thermal and Mechanical and Electrical Equipment at the South-West CHP

    Energy Technology Data Exchange (ETDEWEB)

    Babkin, K. V., E-mail: babkin@uztec.ru; Tsvetkov, M. S.; Kostyuk, R. I.; Chugin, A. V. [SC “South-West CHP” (Russian Federation); Bilenko, V. A.; Molchanov, K. A.; Fedunov, V. V. [JSC “Interautomatika” (Russian Federation)

    2015-01-15

    Results of implementing an SPPA-T3000-based unified distributed control system for thermal and mechanical and electrical equipment at the South-West CHP are discussed. Hardware solutions for integration with local control systems, control of electrical equipment in compliance with the standards IEC 61850, Modbus RTU, and communication between the plant control system and the System Operator of the Unified Power System are described.

  9. Experience of Implementing a Distributed Control System for Thermal and Mechanical and Electrical Equipment at the South-West CHP

    International Nuclear Information System (INIS)

    Babkin, K. V.; Tsvetkov, M. S.; Kostyuk, R. I.; Chugin, A. V.; Bilenko, V. A.; Molchanov, K. A.; Fedunov, V. V.

    2015-01-01

    Results of implementing an SPPA-T3000-based unified distributed control system for thermal and mechanical and electrical equipment at the South-West CHP are discussed. Hardware solutions for integration with local control systems, control of electrical equipment in compliance with the standards IEC 61850, Modbus RTU, and communication between the plant control system and the System Operator of the Unified Power System are described

  10. On the evolution of the regulatory guidance for seismic qualification of electric and active mechanical equipment for nuclear power plants

    International Nuclear Information System (INIS)

    Ng, Ching Hang; Chen, Pei-Ying

    2009-01-01

    All electric and active mechanical equipment important to safety for nuclear power plants must be seismically qualified by testing, analysis, or combined analysis and testing. The general requirements for seismic qualification of electric and active mechanical equipment in nuclear power plants are delineated in Appendix S, 'Earthquake Engineering Criteria for Nuclear Power Plants,' to Title 10, Part 50, 'Domestic Licensing of Production and Utilization Facilities,' of the Code of Federal Regulations (10 CFR Part 50), item 52.47(20) of 10 CFR 52.47, 'Contents of Applications; Technical Information,' and Appendix A, 'Seismic and Geologic Siting Criteria for Nuclear Power Plants,' to 10 CFR Part 100, 'Reactor Site Criteria.' The United States Nuclear Regulatory Commission (NRC) issued Revision 2 of Regulatory Guide (RG) 1.100, 'Seismic Qualification of Electric and Mechanical for Nuclear Power Plants' in 1988, which endorsed, with restrictions, exceptions, and clarifications, Institute of Electrical and Electronics Engineers (IEEE) Standard 344-1987 'IEEE Recommended Practice for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations,' for use in seismic qualification of both electric and mechanical equipment. In 2008, the staff at the NRC drafted Revision 3 of RG 1.100 to endorse, with restrictions, exceptions, and clarifications, the IEEE Std 344-2004 and the American Society of Mechanical Engineers (ASME) QME-1-2007 'Qualification of Active Mechanical Equipment Used in Nuclear Power Plants.' IEEE Std 344-2004 was an update of Std 344-1987 and ASME QME-1-2007 was an update of QME-1-2002. The major changes in IEEE Std 344-2004 and ASME QME-1-2007 include the update and expansion of criteria and procedures describing the use of experience data as a method for seismic qualification of Class 1E electric equipment (including I and C components) as well as active mechanical equipment. In this paper, the staff will compare the draft Revision 3 to

  11. Is the lateral jack-knife position responsible for cases of transient neurapraxia?

    Science.gov (United States)

    Molinares, Diana Margarita; Davis, Timothy T; Fung, Daniel A; Liu, John Chung-Liang; Clark, Stephen; Daily, David; Mok, James M

    2016-01-01

    The lateral jack-knife position is often used during transpsoas surgery to improve access to the spine. Postoperative neurological signs and symptoms are very common after such procedures, and the mechanism is not adequately understood. The objective of this study is to assess if the lateral jack-knife position alone can cause neurapraxia. This study compares neurological status at baseline and after positioning in the 25° right lateral jack-knife (RLJK) and the right lateral decubitus (RLD) position. Fifty healthy volunteers, ages 21 to 35, were randomly assigned to one of 2 groups: Group A (RLD) and Group B (RLJK). Motor and sensory testing was performed prior to positioning. Subjects were placed in the RLD or RLJK position, according to group assignment, for 60 minutes. Motor testing was performed immediately after this 60-minute period and again 60 minutes thereafter. Sensory testing was performed immediately after the 60-minute period and every 15 minutes thereafter, for a total of 5 times. Motor testing was performed by a physical therapist who was blinded to group assignment. A follow-up call was made 7 days after the positioning sessions. Motor deficits were observed in the nondependent lower limb in 100% of the subjects in Group B, and no motor deficits were seen in Group A. Statistically significant differences (p knife positioning for 60 minutes results in neurapraxia of the nondependent lower extremity. Our results support the hypothesis that jack-knife positioning alone can cause postoperative neurological symptoms.

  12. Transitional Experiences of Post-16 Sports Education: Jack's Story

    Science.gov (United States)

    Aldous, David C. R.; Sparkes, Andrew C.; Brown, David H. K.

    2014-01-01

    This paper explores the layered transitional experiences of a semi-professional athlete named Jack (a pseudonym) between the fields of professional sport and further and higher education. Our analysis is framed by the quadripartite framework of structuration and focuses on Jack's "in-situ" practices at his college and university in order…

  13. Program plan for environmental qualification of mechanical and dynamic (including seismic) qualification of mechanical and electrical equipment program (EDQP)

    International Nuclear Information System (INIS)

    Weidenhamer, G.H.

    1986-06-01

    The equipment qualification program described in this plan is intended to provide the technical basis for resolving uncertainties in existing equipment qualification standards. In addition, research results are contributing to the resolution of safety issues GI-23, GI-87, USI-A44, titled, ''Reactor Coolant Pump Seal Failure,'' ''Failure of HPCI Steam Line Without Isolation,'' and ''Station Blackout,'' respectively. Also, research effort is being directed at providing information on the behavior of containment isolation valves under severe accident environments. Although the results of the latter research will not contribute to resolving uncertainties in qualification standards, it has proven cost effective to obtain this information under this program

  14. Simplified method to evaluate seismic nozzle loads on mechanical equipment connected to unbraced piping

    International Nuclear Information System (INIS)

    Detroux, P.; Lafaille, J.P.

    1991-01-01

    After ten years of operation, the Belgian Nuclear Power Plants had to be seismically reassessed; especially, new requirements were imposed to the oldest units. The method, presented in this paper, is based on the principle that all the piping connected to the equipment is replaced by a clamped-hinged beam with or without concentrated mass and of a characteristic length depending on the diameter, schedule, mass per length of the connected piping and on the floor response spectra applicable at the location of the equipment. A theoretical justification of the method is presented for the simplest cases. The case of added concentrated mass is investigated. Finally, several comparisons with a full modal spectral analysis are presented

  15. A hybrid degradation tendency measurement method for mechanical equipment based on moving window and Grey–Markov model

    International Nuclear Information System (INIS)

    Jiang, Wei; Zhou, Jianzhong; Zheng, Yang; Liu, Han

    2017-01-01

    Accurate degradation tendency measurement is vital for the secure operation of mechanical equipment. However, the existing techniques and methodologies for degradation measurement still face challenges, such as lack of appropriate degradation indicator, insufficient accuracy, and poor capability to track the data fluctuation. To solve these problems, a hybrid degradation tendency measurement method for mechanical equipment based on a moving window and Grey–Markov model is proposed in this paper. In the proposed method, a 1D normalized degradation index based on multi-feature fusion is designed to assess the extent of degradation. Subsequently, the moving window algorithm is integrated with the Grey–Markov model for the dynamic update of the model. Two key parameters, namely the step size and the number of states, contribute to the adaptive modeling and multi-step prediction. Finally, three types of combination prediction models are established to measure the degradation trend of equipment. The effectiveness of the proposed method is validated with a case study on the health monitoring of turbine engines. Experimental results show that the proposed method has better performance, in terms of both measuring accuracy and data fluctuation tracing, in comparison with other conventional methods. (paper)

  16. A hybrid degradation tendency measurement method for mechanical equipment based on moving window and Grey-Markov model

    Science.gov (United States)

    Jiang, Wei; Zhou, Jianzhong; Zheng, Yang; Liu, Han

    2017-11-01

    Accurate degradation tendency measurement is vital for the secure operation of mechanical equipment. However, the existing techniques and methodologies for degradation measurement still face challenges, such as lack of appropriate degradation indicator, insufficient accuracy, and poor capability to track the data fluctuation. To solve these problems, a hybrid degradation tendency measurement method for mechanical equipment based on a moving window and Grey-Markov model is proposed in this paper. In the proposed method, a 1D normalized degradation index based on multi-feature fusion is designed to assess the extent of degradation. Subsequently, the moving window algorithm is integrated with the Grey-Markov model for the dynamic update of the model. Two key parameters, namely the step size and the number of states, contribute to the adaptive modeling and multi-step prediction. Finally, three types of combination prediction models are established to measure the degradation trend of equipment. The effectiveness of the proposed method is validated with a case study on the health monitoring of turbine engines. Experimental results show that the proposed method has better performance, in terms of both measuring accuracy and data fluctuation tracing, in comparison with other conventional methods.

  17. An intelligent service matching method for mechanical equipment condition monitoring using the fibre Bragg grating sensor network

    Science.gov (United States)

    Zhang, Fan; Zhou, Zude; Liu, Quan; Xu, Wenjun

    2017-02-01

    Due to the advantages of being able to function under harsh environmental conditions and serving as a distributed condition information source in a networked monitoring system, the fibre Bragg grating (FBG) sensor network has attracted considerable attention for equipment online condition monitoring. To provide an overall conditional view of the mechanical equipment operation, a networked service-oriented condition monitoring framework based on FBG sensing is proposed, together with an intelligent matching method for supporting monitoring service management. In the novel framework, three classes of progressive service matching approaches, including service-chain knowledge database service matching, multi-objective constrained service matching and workflow-driven human-interactive service matching, are developed and integrated with an enhanced particle swarm optimisation (PSO) algorithm as well as a workflow-driven mechanism. Moreover, the manufacturing domain ontology, FBG sensor network structure and monitoring object are considered to facilitate the automatic matching of condition monitoring services to overcome the limitations of traditional service processing methods. The experimental results demonstrate that FBG monitoring services can be selected intelligently, and the developed condition monitoring system can be re-built rapidly as new equipment joins the framework. The effectiveness of the service matching method is also verified by implementing a prototype system together with its performance analysis.

  18. Manager's handbook for jack pine in the north central states.

    Science.gov (United States)

    John W. Benzie

    1977-01-01

    Provides a key for the resource manager to use in choosing silvicultural practices for the management of jack pine. Control of stand composition, growth, and stand establishment for timber production, water, wildlife, and recreation are discussed.

  19. Generalized Jack and Macdonald polynomials arising from AGT conjecture

    Science.gov (United States)

    Ohkubo, Y.

    2017-01-01

    We investigate the existence and the orthogonality of the generalized Jack symmetric functions which play an important role in the AGT relations. We show their orthogonality by deforming them to the generalized Macdonald symmetric functions.

  20. In conversation with Nobel Laureate Jack Steinberger

    CERN Multimedia

    2011-01-01

    Awarded the 1988 Nobel Prize for Physics for his discovery of the muon neutrino, Jack Steinberger has been part of the CERN establishment for almost 50 years. He recently celebrated his 90th birthday and can still be found in his CERN office on an almost daily basis. If you happened to have a coffee with him… this is what he would tell you: his recollections, and thoughts about the present and future of particle physics.   I’ve been at CERN for 45 years, and I’ve seen this organisation go through a lot. Experiments have grown significantly and so have the aspirations of particle physics. When I did my thesis 64 years ago, I could do it alone in just 6 months and I could get worldwide interesting results. Now, experiments at CERN are made up of hundreds, if not thousands of people, working for 20 years to get a result. My thesis advisor was Enrico Fermi, and in 1953 – unless it was 1952, I’d done my thesis a few years before - he was asked to be t...

  1. Objectives of Experimental Validation of Mechanical Equipment for BN-1200 Reactor Plant

    International Nuclear Information System (INIS)

    Timofeev, A.V.; Lyubimov, M.A.

    2013-01-01

    Conclusion: Fabricating and testing the pilot specimens of CRDMs, mockups of main elevator units, and cantilever refueling mechanism make it possible to validate their design. Positive testing results will make it possible to start the work on developing: • final designs of the elevator and cantilever refueling mechanism; • manufacturing design documentation on CRDM prototypes

  2. Design features of selected mechanisms developed for use in Spacelab. [mechanical ground support equipment and environmental control

    Science.gov (United States)

    Inden, W.

    1979-01-01

    Selected mechanisms developed for the Spacelab program are discussed. These include: (1) the roller rail used to install/remove the Spacelab floor loaded with racks carrying experiments; (2) the foot restraint; and (3) the lithium hydroxide used for decontamination.

  3. Engineering and Design: Reliability Analysis of Navigation Lock and Dam Mechanical and Electrical Equipment

    National Research Council Canada - National Science Library

    Beranek, Dwight

    2001-01-01

    This engineer technical letter (ETL) provides guidance for assessing the reliability of mechanical and electrical systems of navigation locks and dams and for establishing an engineering basis for major rehabilitation investment decisions...

  4. Efficacy and efficiency of poultry carcass composting using different mechanical mixing equipment for avian influenza outbreaks

    Directory of Open Access Journals (Sweden)

    Jennifer Elizabeth Keaten

    2017-05-01

    Full Text Available Background and Aim: Avian influenza (AI is a viral disease that caused the largest animal disease outbreak in the history of US agriculture. There are several disposal methods of AI infected poultry carcasses available in the US, which include on-site burial, landfill, incineration, rendering, and composting. Of these methods, composting is the most environmentally friendly and poses a low risk for biosecurity. The United States Department of Agriculture (USDA has developed a comprehensive plan for composting AI infected carcasses. The current protocols have the potential for areas of anaerobic pockets within the windrow due to inadequate mixing and the large carcass size of whole birds. This could lead to ineffective virus neutralization or prolonged composting times and higher resource costs. The purpose of this project was to determine if using a horizontal mixer (HM wagon to mix composting ingredients or a vertical mixer (VM wagon to mix and cut up the compositing ingredients is an economical and timely means to accelerate the tissue break-down and obtain optimal temperatures for poultry carcass composting during an AI outbreak. Materials and Methods: A replicated trial with three treatments, HM, conventional layering (CL and VM, and three replications was initiated at the Compost Research and Education Center part of the University of Maine Forest and Agricultural Experimental Station called High Moor Farm. Daily temperatures and screened core sample weights (screen weights on day 0, 16, and 30 were recorded for each of the compost piles. The time to build each replication was recorded and used to help calculate the cost of each method. Data on equipment, carbon material and labor costs were collected from private contractors from the 2014 to 2016 highly pathogenic AI (HPAI outbreak and used to compare costs between methods. Results: All treatment methods reached USDA protocol temperatures to neutralize the HPAI virus. Screen weights for

  5. A simplified model of natural and mechanical removal to estimate cleanup equipment efficiency

    International Nuclear Information System (INIS)

    Lehr, W.

    2001-01-01

    Oil spill response organizations rely on modelling to make decisions in offshore response operations. Models are used to test different cleanup strategies and to measure the expected cost of cleanup and the reduction in environmental impact. The oil spill response community has traditionally used the concept of worst case scenario in developing contingency plans for spill response. However, there are many drawbacks to this approach. The Hazardous Materials Response Division of the National Oceanic and Atmospheric Administration in Cooperation with the U.S. Navy Supervisor of Salvage and Diving has developed a Trajectory Analysis Planner (TAP) which will give planners the tool to try out different cleanup strategies and equipment configurations based upon historical wind and current conditions instead of worst-case scenarios. The spill trajectory model is a classic example in oil spill modelling that uses advanced non-linear three-dimensional hydrodynamical sub-models to estimate surface currents under conditions where oceanographic initial conditions are not accurately known and forecasts of wind stress are unreliable. In order to get better answers, it is often necessary to refine input values rather than increasing the sophistication of the hydrodynamics. This paper described another spill example where the level of complexity of the algorithms needs to be evaluated with regard to the reliability of the input, the sensitivity of the answers to input and model parameters, and the comparative reliability of other algorithms in the model. 9 refs., 1 fig

  6. Remote mechanized equipment for the repair and replacement of boiling water reactor recirculation loop piping

    International Nuclear Information System (INIS)

    Mauser, D.; Busch, D.F.

    1983-01-01

    Equipment has been assembled for the remote repair or replacement of boiling water reactor nuclear plant piping in the diameter range of 4 to 28 inches (10-71 cm). The objectives of this program were to produce high-quality pipe welds, reduce plant downtime, and reduce man-rem exposure. The repair strategy was to permit repair personnel to install and check out the repair subsystems and then leave the radiation zone allowing the operations to be conducted at a distance of up to 300 feet (91 m) from the operator. The complete repair system comprises subsystems for pipe severing, dimensional gaging, joint preparation, counterboring, welding, postweld nondestructive inspection (conceptual design), and audio, electronic, and visual monitoring of all operations. Components for all subsystems, excluding those for postweld nondestructive inspection, were purchased and modified as needed for integration into the repair system. Subsystems were designed for two sizes of Type 304 stainless steelpipe. For smaller, 12-inch-diameter (30.5 cm) pipe, severing is accomplished by a power hack saw and joint preparation and counterboring by an internally mounted lathe. The 22-inch-diameter (56 cm) pipe is severed, prepared, and counterbored using an externally mounted, single-point machining device. Dimensional gaging is performed to characterize the pipe geometry relative to a fixed external reference surface, allowing the placement of the joint preparation and the counterbore to be optimized. For both pipe sizes, a track-mounted gas tungsten-arc welding head with filler wire feed is used

  7. Estimation of the cost of electro-mechanical equipment for small hydropower plants – review and comparison of methods

    Directory of Open Access Journals (Sweden)

    Lipiński Seweryn

    2017-01-01

    Full Text Available The estimate of the cost of electro-mechanical equipment for new small hydropower plants most often amounts to about 30-40% of the total budget. In case of modernization of existing installations, this estimation represents the main cost. This matter constitutes a research problem for at least few decades. Many models have been developed for that purpose. The aim of our work was to collect and analyse formulas that allow estimation of the cost of investment in electro-mechanical equipment for small hydropower plants. Over a dozen functions were analysed. To achieve the aim of our work, these functions were converted into the form allowing their comparison. Then the costs were simulated with respect to plants’ powers and net heads; such approach is novel and allows deeper discussion of the problem, as well as drawing broader conclusions. The following conclusions can be drawn: significant differences in results obtained by using various formulas were observed; there is a need for a wide study based on national investments in small hydropower plants that would allow to develop equations based on local data; the obtained formulas would let to determinate the costs of modernization or a new construction of small hydropower plant more precisely; special attention should be payed to formulas considering turbine type.

  8. Time expenditure in computer aided time studies implemented for highly mechanized forest equipment

    Directory of Open Access Journals (Sweden)

    Elena Camelia Mușat

    2016-06-01

    Full Text Available Time studies represent important tools that are used in forest operations research to produce empirical models or to comparatively assess the performance of two or more operational alternatives with the general aim to predict the performance of operational behavior, choose the most adequate equipment or eliminate the useless time. There is a long tradition in collecting the needed data in a traditional fashion, but this approach has its limitations, and it is likely that in the future the use of professional software would be extended is such preoccupations as this kind of tools have been already implemented. However, little to no information is available in what concerns the performance of data analyzing tasks when using purpose-built professional time studying software in such research preoccupations, while the resources needed to conduct time studies, including here the time may be quite intensive. Our study aimed to model the relations between the variation of time needed to analyze the video-recorded time study data and the variation of some measured independent variables for a complex organization of a work cycle. The results of our study indicate that the number of work elements which were separated within a work cycle as well as the delay-free cycle time and the software functionalities that were used during data analysis, significantly affected the time expenditure needed to analyze the data (α=0.01, p<0.01. Under the conditions of this study, where the average duration of a work cycle was of about 48 seconds and the number of separated work elements was of about 14, the speed that was usedto replay the video files significantly affected the mean time expenditure which averaged about 273 seconds for half of the real speed and about 192 seconds for an analyzing speed that equaled the real speed. We argue that different study designs as well as the parameters used within the software are likely to produce

  9. Jack of all trades: Versatile catechol crosslinking mechanisms

    NARCIS (Netherlands)

    Yang, J.; Cohen Stuart, M.A.; Kamperman, M.M.G.

    2014-01-01

    Catechols play an important role in many natural systems. They are known to readily interact with both organic (e.g., amino acids) and inorganic (e.g., metal ions, metal oxides) compounds, thereby providing a powerful system for protein curing. Catechol crosslinked protein networks, such as

  10. Jack-of-all-trades effects drive biodiversity–ecosystem multifunctionality relationships in European forests

    Science.gov (United States)

    van der Plas, Fons; Manning, Peter; Allan, Eric; Scherer-Lorenzen, Michael; Verheyen, Kris; Wirth, Christian; Zavala, Miguel A.; Hector, Andy; Ampoorter, Evy; Baeten, Lander; Barbaro, Luc; Bauhus, Jürgen; Benavides, Raquel; Benneter, Adam; Berthold, Felix; Bonal, Damien; Bouriaud, Olivier; Bruelheide, Helge; Bussotti, Filippo; Carnol, Monique; Castagneyrol, Bastien; Charbonnier, Yohan; Coomes, David; Coppi, Andrea; Bastias, Cristina C.; Muhie Dawud, Seid; De Wandeler, Hans; Domisch, Timo; Finér, Leena; Gessler, Arthur; Granier, André; Grossiord, Charlotte; Guyot, Virginie; Hättenschwiler, Stephan; Jactel, Hervé; Jaroszewicz, Bogdan; Joly, François-Xavier; Jucker, Tommaso; Koricheva, Julia; Milligan, Harriet; Müller, Sandra; Muys, Bart; Nguyen, Diem; Pollastrini, Martina; Raulund-Rasmussen, Karsten; Selvi, Federico; Stenlid, Jan; Valladares, Fernando; Vesterdal, Lars; Zielínski, Dawid; Fischer, Markus

    2016-01-01

    There is considerable evidence that biodiversity promotes multiple ecosystem functions (multifunctionality), thus ensuring the delivery of ecosystem services important for human well-being. However, the mechanisms underlying this relationship are poorly understood, especially in natural ecosystems. We develop a novel approach to partition biodiversity effects on multifunctionality into three mechanisms and apply this to European forest data. We show that throughout Europe, tree diversity is positively related with multifunctionality when moderate levels of functioning are required, but negatively when very high function levels are desired. For two well-known mechanisms, ‘complementarity' and ‘selection', we detect only minor effects on multifunctionality. Instead a third, so far overlooked mechanism, the ‘jack-of-all-trades' effect, caused by the averaging of individual species effects on function, drives observed patterns. Simulations demonstrate that jack-of-all-trades effects occur whenever species effects on different functions are not perfectly correlated, meaning they may contribute to diversity–multifunctionality relationships in many of the world's ecosystems. PMID:27010076

  11. Heritability and intertrait correlations in breeding subpopulations of jack pine

    Science.gov (United States)

    Don E. Riemenschneider

    1985-01-01

    Twenty breeding populations of jack pine were established in 1979 and 1980 in Minnesota, Wisconsin, and Michigan. Four populations were index populations and were each established at 4 locations by research cooperators. Sixteen populations were applied breeding populations and were established at single locations by public and private cooperators. Combined analysis of...

  12. The Authority and Charismas of Jack Ma's Leadership

    Institute of Scientific and Technical Information of China (English)

    陈希

    2014-01-01

    Jack Ma is the top manager of Ali Baba group, with a strong leadership. He mixes autocratic leadership and charismatic leadership together. The powers he used are from his position, the reward system of the company and the charismas to gain his leading power. In addition, he uses his charismas and his achievements to win the trust of the employees, which develop his leadership.

  13. Book Review: Jack Simons: Teacher, Scholar, Comrade: A Jacana ...

    African Journals Online (AJOL)

    Book Title: Jack Simons: Teacher, Scholar, Comrade: A Jacana Pocket Biography. Book Author: Hugh Macmillan. Jacana: Auckland Park, 2016. 167 pp. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL.

  14. Geographic variation of jack pine (Pinus banksiana Lamb.)

    Science.gov (United States)

    Jung Oh Hyun

    1977-01-01

    Ten traits were measured on 10-year-old jack pine grown at Cloquet, Minnesota, from seed collected from 90 provenances. The traits were examined by using analysis of variance and computing correlations for all combinations of 9 traits plus latitude , longitude, and elevation of the seed sources and cluster analyses using the D2 values from the...

  15. JACK LONDON ETNÓLOGO AMATEUR DEL PUGILISMO

    Directory of Open Access Journals (Sweden)

    Loïc Wacquant

    2012-12-01

    Full Text Available De los relatos que Jack London ha consagrado al boxeo, A Piece of Steak es sin dudas aquel que merece hoy nuestra mayor atención, e incluso un lugar en el panteón de los textos literarios sobre el Noble Arte, y junto a él otros tres títulos...

  16. Functional properties of unmodified and modified Jack bean ...

    African Journals Online (AJOL)

    The native Jack bean (Canavalia eniformis) starch was chemically modified through oxidation and acetylation. Proximate composition analysis revealed higher moisture, protein, fat and ash contents 'native unmodified than modified starches and higher yield in modified starches. Swelling capacity and solubility of all the ...

  17. Recollections of Jack Michael and the Application of Skinner's Analysis of Verbal Behavior

    Science.gov (United States)

    Sundberg, Mark L.

    2017-01-01

    Jack Michael offered a course on verbal behavior almost every year throughout his teaching career. Jack was also interested in the application of Skinner's work and in 1976 began to offer a graduate course at Western Michigan University titled Verbal Behavior Applications. Jack and his students pursued the application of Skinner's work on verbal…

  18. Psychoanalysis of Jack London's "The Call of the Wild" and "White Fang"

    Science.gov (United States)

    Yang, Hongyan

    2015-01-01

    "The Call of the Wild" and "White Fang" both are masterpieces of Jack London. The protagonists Buck and White Fang are the incarnation of Jack himself to some extent for the two novels reveal a great deal of the writer. This essay aims at psychoanalyzing Jack London's creative process, the Oedipus complex and the confliction…

  19. Modular jack-up platform debuts in Peru's Amazon jungle

    Energy Technology Data Exchange (ETDEWEB)

    Franco, A.

    1975-08-11

    Robishaw Engineering Inc., Houston, has designed and built a jack-up platform based on a modular flotation and erection system that allows exploratory and development drilling year round in any location that cannot be reached by conventional equipment. All components are light enough to be transported by helicopters rated for 4000-lb loads, yet strong and buoyant enough to serve as working platforms. The pile-supported self-elevating drilling platform consists of H-shaped steel girders joined by pin connectors and tension wires. Deck panels are steel-plated. When elevated on steel pilings, the platform can support loads imposed by rigs capable of drilling to 18,000 ft. One such unit is currently being used in the Peruvian rain forest.

  20. Footprint study in children during the Jack test

    OpenAIRE

    Pinto, José Antonio; Saito, Edgar; Lira Neto, Ozório Almeida; Rowinski, Sérgio; Blumetti, Francesco Camara; Dobashi, Eiffel Tsuyoshi

    2011-01-01

    OBJETIVO: Avaliar as impressões plantares durante o teste de Jack em crianças quantificando e observando os resultados numa faixa etária crítica para a formação do arco plantar. MÉTODO: Avaliamos 60 crianças brancas (120 pés) sendo 35 meninos e 25 meninas com idades entre 2 e 5 anos, sem queixas ortopédicas. Simulamos o teste de Jack com uma órtese em cunha de 45º apoiada sob o hálux. Obtivemos impressões em apoio monopodálico bilateralmente utilizando um pedígrafo. O exame dividiu-se em dua...

  1. Inflatable Indian travel pillow as a pneumatic patient jack

    Directory of Open Access Journals (Sweden)

    Gopalakrishna A

    2006-01-01

    Full Text Available The Indian travel pillow readily available in the market has been utilized as a patient jack in the operation theatre. This has been used to raise the shoulders of an anaesthetized patient for surgery in the head and neck region and a set of two pillows have been used to prop-up a prone anaesthetized patient. This allows smooth positioning of the patient after intubation without disturbance to the airway with minimal manpower.

  2. Development of a urinary lithiasis localizer mechanism to couple ultrasound and extracorporeal lithotripsy equipment in canine model

    Directory of Open Access Journals (Sweden)

    Enrico Andrade

    2006-10-01

    Full Text Available INTRODUCTION: Due to the evolution of extracorporeal lithotripsy equipment (ESWL and presently, the fact that most part of the equipment does not present ultrasound to localize urinary calculi, a system that allows adapting ultrasound equipment to ESWL equipment was developed, disposing only of fluoroscopy. Thus, this equipment was developed and was tested in urinary stones in canine models, to check its precision in relation to fluoroscopy. METHOD: Seven male dogs were utilized with the introduction, in the bladder through the ureteral route, of chalkstones, with initial localization by fluoroscopy, with a further ultrasound coincidence check localization of the vesical stones, being submitted to ESWL with a 3-hour, 21 days and 60 days follow-up after the procedure. RESULTS: Success of localization in all animals was verified presenting elimination of stones in the first micturitions, after ESWL. No complications were verified in those animals for 60 days. CONCLUSION: We verified that this equipment can lead to an update of the equipment that use only fluoroscopy, increasing in this way, their technical capacity in the treatment of urinary calculi, mainly in cases of non-radiopaque stones.

  3. Seeing is believing -- SpyJack system investigates field problems

    International Nuclear Information System (INIS)

    O'Meara, D.

    1998-01-01

    The SpyJack Remote Monitoring System, a stand-alone, single-site remote well monitoring system that works off its own embedded controller is described. The supervisory control and data acquisition (SCADA) unit, developed by CORE Technologies Inc., has an integrated voice/alarm system, monitoring sensors installed at remote well sites continuously 24 hours a day with a digital camera, with 300 degrees of visual confirmation capability. It can also be used as a surveillance tool against terrorism as has been shown in the case of some recent debilitating attacks on remote wells in Alberta. SpyJack monitors flow rates and pressures, pumpjack stroke rates, sucker rod temperature, load cell and engine shut-off relay, as well as ambient temperature, tank levels, and motion detection. At the office, SpyJack Well Management Interface uses nine drop-down screens to take users through the remote monitoring and control of each site. The screens include production sensors, line sensors, dyno chart, environmental/safety sensors and sensor information and set up. Currently under development is the unsolicited dial-out capability. When implemented the system will send out information at pre-determined times, such as every four hours, or at specific times during the day. Compressing images to enable speedier downloading is also being planned

  4. Statistical analysis of the behaviour of the mechanical equipment of EDFs power plants - evaluation of the availability and safety of thermal and nuclear units

    International Nuclear Information System (INIS)

    Procaccia, H.; Brillon, A.; Cravero, M.; Lucenet, G.

    1975-01-01

    The investigation and research directorate of EDF has undertaken a statistical analysis of the behaviour of large mechanical equipment at conventional power stations during the ten years following the operating reports of these stations. It has thus been possible to determine the intrinsic reliability, the failure rate, the mean repair time, and the mean good operating time of feed water reheating points, power turbines, pumps and boilers of the various EDF plants (125 and 250 MW) leading to a consideration of the feasibility of an extrapolation to present and future plants. Based on these elementary investigation two methods of calculation have been developed. One is used to assess the overall availability of a thermal or nuclear power station based on the knowledge of the failure rates of the equipment, each piece of equipment being associated with an idea of its technical importance in the functioning of the equipment. A numerical application is given for 125 and 250 MW conventional plants. The purpose of the other method is to estimate the operational safety of the safety equipment of nuclear power stations, based on the development of tree diagrams for faults in basic equipment. A numerical example is given for the cooling systems for Phenix and for one of the Super Phenix versions. (author)

  5. Finite element simulations of two rock mechanics tests

    International Nuclear Information System (INIS)

    Dahlke, H.J.; Lott, S.A.

    1986-04-01

    Rock mechanics tests are performed to determine in situ stress conditions and material properties of an underground rock mass. To design stable underground facilities for the permanent storage of high-level nuclear waste, determination of these properties and conditions is a necessary first step. However, before a test and its associated equipment can be designed, the engineer needs to know the range of expected values to be measured by the instruments. Sensitivity studies by means of finite element simulations are employed in this preliminary design phase to evaluate the pertinent parameters and their effects on the proposed measurements. The simulations, of two typical rock mechanics tests, the plate bearing test and the flat-jack test, by means of the finite element analysis, are described. The plate bearing test is used to determine the rock mass deformation modulus. The flat-jack test is used to determine the in situ stress conditions of the host rock. For the plate bearing test, two finite element models are used to simulate the classic problem of a load on an elastic half space and the actual problem of a plate bearing test in an underground tunnel of circular cross section. For the flat-jack simulation, a single finite element model is used to simulate both horizontal and vertical slots. Results will be compared to closed-form solutions available in the literature

  6. A novel mechanical design of broken rope protection device for enhancing the safety performances of overhead manned equipment in coal mine

    Directory of Open Access Journals (Sweden)

    Xiaoguang Zhang

    2015-08-01

    Full Text Available A novel mechanical design of the broken rope protection device is proposed to enhance the safety performances of the overhead manned equipment. According to the operating characteristics and functional requirements of the overhead manned equipment, a three-dimensional mechanical model of the broken rope protection device was redesigned. Based on the known parameters of the mechanical model, the stress and strength of the main components are readjusted using the statics characteristics of finite element analysis. To ensure the reliability of the control system of the broken rope protection device, the process of people’s falling, the response performance of the tension sensor, and the signal extraction of the broken rope are analyzed under different loading and unloading speeds. The working principle of the broken rope protection device is expounded in detail. The experimental results showed that better effect is obtained by the new broken rope protection device, which is characterized by good durability, low investment, and high reliability.

  7. Students Learning Physics While Lifting Themselves: A Simple Analysis of a Scissors Jack

    Science.gov (United States)

    Haugland, Ole Anton

    2017-01-01

    Every time I have to jack up my car, I am a bit surprised by how slowly the scissors jack works the higher I raise it, and close to maximum height I need very little force to turn the crank. This agrees well with the principle of simple machines. Since I have to jack up my car at least twice a year to change between winter tires and summer tires,…

  8. The influence of musical cadence into aquatic jumping jacks kinematics.

    Science.gov (United States)

    Costa, Mário J; Oliveira, Cristiana; Teixeira, Genoveva; Marinho, Daniel A; Silva, António J; Barbosa, Tiago M

    2011-01-01

    The aim of this study was to analyze the relationships between the head-out aquatic exercise "Jumping jacks" kinematics and the musical cadence in healthy and fit subjects. Five young women, with at least one year of experience conducting head- out aquatic programs were videotaped in the frontal plane, with a pair of cameras providing a double projection (above and below the water surface). Subjects performed an incremental protocol of five bouts (120 b·min(-1), 135 b·min(-1), 150 b·min(-1), 165 b·min(-1) and 180 b·min(-1)) with 16 full cycles of the "Jumping jacks" exercise. Data processing and calculation of upper limbs' (i.e. hands), lower limbs' (i.e. feet) and center of mass' 2D linear velocity and displacement were computed with the software Ariel Performance Analysis System and applying the 2D-DLT algorithm. Subjects decreased the cycle period during the incremental protocol. Significant and negative relationships with the musical cadence were verified for the center of mass and upper limbs vertical displacement. On the other hand, for the lower limbs lateral velocity, a significant and positive relationship was observed. It is concluded that expert and fit subjects increase the lower limb's velocity to maintain the range of motion, while the upper limb's displacement is reduced to coupe the music cadence. Key pointsWhile performing the Jumping Jacks, expert and fit subjects increase their lower limbs segmental velocity to maintain the range of motion.The upper limbs displacement is reduced to maintain the music cadence.Expert and fit subjects present similar response for alternating or simultaneously head-out aquatic exercises when increasing the music cadence.

  9. Mississippi Curriculum Framework for Diesel Equipment Technology (CIP: 47.0605--Diesel Engine Mechanic & Repairer). Postsecondary Programs.

    Science.gov (United States)

    Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

    This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for the course sequences in the diesel equipment technology programs cluster. Presented in the introductory section are a description of the program and suggested course sequence. Section I lists baseline competencies,…

  10. Fire protection in nuclear power plants. Pt. 3. Fire protection for mechanical and electrotechnical equipment and components

    International Nuclear Information System (INIS)

    1994-01-01

    The KTA rule applies to LWRs and defines requirements to be met for fire protection of equipment and installations of the safety system, and all safety-relevant systems, and of those operating systems that under the effect of fire, may cause improper functioning of safety system components. (orig./HP) [de

  11. Forest Modeling of Jack Pine Trees for BOREAS

    Science.gov (United States)

    Moghhadam, Mahta; Saatchi, Sasan

    1994-01-01

    As a part of the intensive field campaign for the Boreal forest ecosystem-atmosphere research (BOREAS) project in August 1993, the NASA/JPL AIRSAR covered an area of about 100 km by 100 km near the Prince Albert National Park in Saskatchewan, Canada. At the same time, ground-truth measurements were made in several stands which have been selected as the primary study sites, as well as in some auxiliary sites. This paper focuses on an area including Jack Pine stands in the Nipawin area near the park.

  12. Destructive Cholangitis in an Adult Jack Russell Terrier

    Directory of Open Access Journals (Sweden)

    Atsushi Kodama

    2012-01-01

    Full Text Available A 4-year-old female Jack Russell terrier dog exhibited vomiting and severe jaundice of the visible mucous membranes and skin. Ultrasonography revealed diffuse areas of high echogenicity and focal areas of low echogenicity in the left lobe of the liver. On macroscopic observation of the biopsied liver specimen, many scattered irregularly shaped red spots were observed on the liver surface and on the cut surface. Histopathologically, there was loss of the interlobular bile duct and cholangitis accompanied by infiltration of pigment-laden macrophages in the Glisson’s capsule. Therefore, in the present case the dog was diagnosed with destructive cholangitis.

  13. CoJACK: A High-Level Cognitive Architecture with Demonstrations of Moderators, Variability, and Implications for Situation Awareness

    Science.gov (United States)

    2012-01-01

    defined, to CoJACK (Ritter, Reifers, Klein, & Schoelles, 2007) based on task appraisal theory (e.g., Cannon, 1932; Lazarus & Folkman , 1984; Selye...Cambridge, MA: MIT Press. Lazarus , R. S., & Folkman , S. (1984). Stress, appraisal and coping. New York: Springer Publishing. Lovett, M. C., Daily, L...promising. 0 0.5 1 1.5 2 2.5 3 3.5 4 Java JACK Default CoJack CoJack Caffeine CoJack Challenged CoJack Threatened Agent Type Ta n k s D es tr o y e d

  14. Implementation and adoption of mechanical patient lift equipment in the hospital setting: The importance of organizational and cultural factors.

    Science.gov (United States)

    Schoenfisch, Ashley L; Myers, Douglas J; Pompeii, Lisa A; Lipscomb, Hester J

    2011-12-01

    Work focused on understanding implementation and adoption of interventions designed to prevent patient-handling injuries in the hospital setting is lacking in the injury literature and may be more insightful than more traditional evaluation measures. Data from focus groups with health care workers were used to describe barriers and promoters of the adoption of patient lift equipment and a shift to a "minimal-manual lift environment" at two affiliated hospitals. Several factors influencing the adoption of the lift equipment and patient-handling policy were noted: time, knowledge/ability, staffing, patient characteristics, and organizational and cultural aspects of work. The adoption process was complex, and considerable variability by hospital and across units was observed. The use of qualitative data can enhance the understanding of factors that influence implementation and adoption of interventions designed to prevent patient-handling injuries among health care workers. Copyright © 2011 Wiley Periodicals, Inc.

  15. Comparison of Sparse and Jack-knife partial least squares regression methods for variable selection

    DEFF Research Database (Denmark)

    Karaman, Ibrahim; Qannari, El Mostafa; Martens, Harald

    2013-01-01

    The objective of this study was to compare two different techniques of variable selection, Sparse PLSR and Jack-knife PLSR, with respect to their predictive ability and their ability to identify relevant variables. Sparse PLSR is a method that is frequently used in genomics, whereas Jack-knife PL...

  16. Using Black Light to Find Jack-Pine Budworm Egg Masses

    Science.gov (United States)

    Daniel T. Jennings

    1968-01-01

    Jack pine foliage infested with jack-pine budworm egg masses was examined under two kinds of light -- black light and a combination of natural and fluorescent light. Black light significantly increased the accuracy of count but not the efficiency of examination.

  17. Investigating the Jack the Ripper Case: Engaging Students in a Criminal Investigations Class through Active Learning

    Science.gov (United States)

    Gutierrez, Daniel; Kazmi, Syed

    2010-01-01

    The present study examines the utilization of a class project involving the Jack the Ripper murders. Students enrolled in a criminal investigations class were required to investigate the five canonical murders associated with the infamous serial killer known as Jack the Ripper and the murders that occurred in London during 1888. This paper…

  18. Equipment considerations

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Trace or ultratrace analyses require that the HPLC equipment used, including the detector, be optimal for such determinations. HPLC detectors are discussed at length in Chapter 4; discussion here is limited to the rest of the equipment. In general, commercial equipment is adequate for trace analysis; however, as the authors approach ultratrace analysis, it becomes very important to examine the equipment thoroughly and optimize it, where possible. For this reason they will review the equipment commonly used in HPLC and discuss the optimization steps. Detectability in HPLC is influenced by two factors (1): (a) baseline noise or other interferences that lead to errors in assigning the baseline absorbance; (b) peak width. 87 refs

  19. Assessment of the TRANSREC-350 mechanical recovery capacity of the oil spill response equipment in Prince William Sound

    International Nuclear Information System (INIS)

    Provant, S.G.

    1992-01-01

    Studies were conducted to determine the compliance of oil spill response equipment in Prince William Sound, Alaska, to state standards. Data on the observed performance of the Framo TRANSREC skimmer, which represents a large portion of the initial response skimming capability of the Sound's equipment, were obtained from Norwegian experience. The results of the analysis are based on the level of performance expected from well-trained skimmer crews responding to a 300,000 bbl spill under the worst average weather conditions over a 72-h period. Certain assumptions are made about volumes of evaporation and decanting. Results indicate that the volume of oil expected to be recovered would be 188,900 bbl, which would expand via emulsion formation to 303,000 bbl. In addition, a volume of free water would be taken in with the emulsion, which would be reduced by decanting. The overall storage capacity needed would then be 382,300 bbl. With the present available configuration of skimmers and barges, the maximum available storage capacity is 370,000 bbl. Skimmer capability can be maximized by matching storage capacity to recovery capability or by developing and demonstrating a capability to offload the recovered oil effectively such that transfer operations do not materially affect recovery operations. Recommendations are made for spill response organizations to improve their operations. 4 refs., 9 figs

  20. Differential effects of plant ontogeny and damage type on phloem and foliage monoterpenes in jack pine (Pinus banksiana).

    Science.gov (United States)

    Erbilgin, Nadir; Colgan, L Jessie

    2012-08-01

    Coniferous trees have both constitutive and inducible defences that deter or kill herbivores and pathogens. We investigated constitutive and induced monoterpene responses of jack pine (Pinus banksiana Lamb.) to a number of damage types: a fungal associate of the mountain pine beetle (Dendroctonus ponderosae Hopkins), Grosmannia clavigera (Robinson-Jeffrey & R.W. Davidson); two phytohormones, methyl jasmonate (MJ) and methyl salicylate (MS); simulated herbivory; and mechanical wounding. We only included the fungal, MJ and mechanical wounding treatments in the field experiments while all treatments were part of the greenhouse studies. We focused on both constitutive and induced responses between juvenile and mature jack pine trees and differences in defences between phloem and needles. We found that phytohormone applications and fungal inoculation resulted in the greatest increase in monoterpenes in both juvenile and mature trees. Additionally, damage types differentially affected the proportions of individual monoterpenes: MJ-treated mature trees had higher myrcene and β-pinene than fungal-inoculated mature trees, while needles of juveniles inoculated with the fungus contained higher limonene than MJ- or MS-treated juveniles. Although the constitutive monoterpenes were higher in the phloem of juveniles than mature jack pine trees, the phloem of mature trees had a much higher magnitude of induction. Further, induced monoterpene concentrations in juveniles were higher in phloem than in needles. There was no difference in monoterpene concentration between phytohormone applications and G. clavigera inoculation in mature trees, while in juvenile trees MJ was different from both G. clavigera and simulated herbivory in needle monoterpenes, but there was no difference between phytohormone applications and simulated herbivory in the phloem.

  1. The characters God and Hamlet by Jack Miles

    Directory of Open Access Journals (Sweden)

    Tania de Fátima da Silva

    2015-04-01

    Full Text Available In the book “God - A Biography,” Jack Miles aims to introduce ourselves Creator-God as a literary character. Miles developed a narrative based on concept aristotelian, in other words, the structure of the work is made from beginning to end. This procedure established a harmony arising from the interaction between the parties, which contributes to scrutinize the precise details of the story of the main protagonist. We decided to highlight that time some characteristics of the main character of the work and compare them to the character Hamlet, by William Shakespeare, because from the beginning of the narrative to completion Miles calls the reader’s attention to the play Shakespeare.

  2. Solar drying of jack fruit almonds Secagem solar de amêndoas de jaca

    Directory of Open Access Journals (Sweden)

    Alexandre J. de M Queiroz

    2011-12-01

    Full Text Available Dryers heated by solar energy have been constructed and used in drying whole and half jack fruit almonds. The samples were dried during the day in direct sun and in the conventional solar dryer prepared for this purpose. Another piece of equipment was built for reception and accumulation of sun energy in a body of water, which was used as a heat source for night drying. The drying with the sun energy was compared with artificial drying. The jack fruit almonds were dried whole, half, with pellicle and without it. The storage of solar energy in water was technically viable for use in night drying. The drying by combining solar dryers in the day and night periods were completed in approximately 35 hours, and were equivalent to artificial drying between 40ºC and 70ºC. Almond cut in half and the pellicle removed reduced the drying time.Secadores com aquecimento por energia solar foram construídos e utilizados em secagens de amêndoas de jaca inteiras e em metades. As secagens no período diurno foram realizadas por exposição direta ao sol e em secador solar convencional, elaborado para este fim. Construiu-se também um equipamento para captação e acumulação de energia solar em uma massa de água, a qual foi utilizada como fonte de calor para realização de secagens no período noturno. As secagens com o uso de energia solar foram comparadas com secagens artificiais. As amêndoas de jaca foram secadas inteiras, em metades, com e sem película. O armazenamento da energia solar em corpo de água mostrou-se viável do ponto de vista técnico para utilização em secagens noturnas. As secagens combinando secadores por energia solar nos períodos diurno e noturno foram concluídas em tempos aproximados de 35 horas e equivaleram a secagens artificiais entre 40 ºC e 70 ºC. O corte das amêndoas e a retirada das películas reduziram o tempo de secagem.

  3. Seismic and dynamic qualification of safety-related electrical and mechanical equipment in operating nuclear power plants: development of a method to generate generic floor-response spectra

    International Nuclear Information System (INIS)

    Curreri, J.; Costantino, C.; Subudhi, M.; Reich, M.

    1983-09-01

    Generic floor response spectra were developed for use in the qualification of electrical and mechanical equipment in operating nuclear power plants. The characteristics of 1000 floor response spectra were studied to determine the generic spectra. The procedure developed uses as much or as little information that currently exists at the plant relating to the question of equipment qualification. The general approach was to study the effects on the dynamic characteristics of each of the elements in the chain of events that goes between the loads and the responses. This includes the loads, the soils and the structures. A free-field earthquake response spectra was used to generate horizontal earthquake time histories. The excitation was applied through the soil and into the various structures to produce responses in equipment. An entire range of soil conditions was used with each structure. Actual PWR and BWR - Mark I structural models were used. For each model, the stiffness properties were varied, with the same mass, so as to extend the fundamental base structure natural frequency from 2 cps to 36 cps. The natural frequencies of the structures were varied to obtain maximum response conditions. The actual properties were first used to locate the natural frequencies. The stiffness properties were than varied, with the same mass, to extend the range of the fundamental base structure natural frequency. The intention was to have the coupled structural material frequencies in the vicinity of the peak amplitude frequency content of the excitation spectrum. Particular attention was therefore given to the frequency band between 2 Hz and 4 Hz. A horizontal generic floor response spectra is proposed for the top level of a generic structure. Reduction factors are applied to the peak acceleration for equipment at lower levels

  4. Increased air temperature during simulated autumn conditions does not increase photosynthetic carbon gain but affects the dissipation of excess energy in seedlings of the evergreen Conifer Jack Pine

    OpenAIRE

    Busch, F.; Huner, N.; Ensminger, I.

    2007-01-01

    Temperature and daylength act as environmental signals that determine the length of the growing season in boreal evergreen conifers. Climate change might affect the seasonal development of these trees, as they will experience naturally decreasing daylength during autumn, while at the same time warmer air temperature will maintain photosynthesis and respiration. We characterized the down-regulation of photosynthetic gas exchange and the mechanisms involved in the dissipation of energy in Jack ...

  5. Mississippi Curriculum Framework for Diesel Equipment Repair & Service (Program CIP: 47.0605--Diesel Engine Mechanic & Repairer). Secondary Programs.

    Science.gov (United States)

    Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

    This document, which reflects Mississippi's statutory requirement that instructional programs be based on core curricula and performance-based assessment, contains outlines of the instructional units required in local instructional management plans and daily lesson plans for diesel engine mechanics I and II. Presented first are a program…

  6. A-jacks and Aquawrap installations in Utah : scour revetment performance evaluation, final report, December 2009.

    Science.gov (United States)

    2009-12-01

    This is a performance evaluation report for A-Jacks, an articulated concrete block designed to protect bridge elements exposed to the river scouring forces, and for Aquawrap, a glass fiber reinforced polymer designed to protect and strengthen bridge ...

  7. Léon Lederman, Mel Schwartz and Jack Steinberger wre awarded the 1988 Nobel Physics Prize.

    CERN Multimedia

    Photographic Service

    1988-01-01

    Léon Lederman (left), Mel Schwartz (right) and Jack Steinberger were awarded the 1988 Nobel Physics Prize for their 1962 experiment at Brookhaven which showed that neutrinos come in more than one kind.

  8. Teistsugune vaade juhtide tasustamisele / Jack Welch, Suzy Welch ; intervjueerinud Stefan Eiselin

    Index Scriptorium Estoniae

    Welch, Jack

    2010-01-01

    USA juhtimisspetsialistide Jack ja Suzy Welchi hinnangul võib tippjuhtidele makstava palga ümber kerkinud poleemika üks võimalikke põhjuseid lisaks halvale kommunikatsioonile olla ka ideoloogiate kokkusobimatus

  9. A Change in Igneous Activity of the Jack Hills Zircon Sources ca. 3.9 Ga

    Science.gov (United States)

    Bell, E. A.; Harrison, T. M.

    2010-12-01

    New Ti-in-zircon crystallization temperature (Txlln) data for Jack Hills zircons reveal that the tight clustering of Hadean grains around a Txlln of 680°C, possibly indicative of felsic-to-intermediate minimum melting conditions, continues to ~3.92 Ga. Between 3.92-3.82 Ga the 680°C clustering ceases and most concordant grains cluster around an apparent Txlln of 610°C. A small group of zircons with higher Txlln (~750°C), present during the Hadean, is also observed during this period. After 3.82 Ga a Hadean-like distribution resumes for ~100 Ma. This large, concordant, low-Ti group at ~3.9 Ga is statistically distinct from the Hadean distribution and appears to be unique in the Jack Hills zircon record. The existence of coeval high- and low-Ti groups suggests that two distinct zircon-forming processes are distinguishable ~3.9 Ga, unlike during the Hadean. The significant numbers of zircons with apparent Txlln below 600°C may be suggestive of subsolidus formation, since igneous units with solidii below 600°C are relatively rare. The higher-Ti group is more consistent with an intermediate to mafic igneous origin but metamorphic overprinting or subsolidus formation at granulite grade cannot be ruled out by Txlln alone. A substantial proportion of the high-Ti group display oscillatory and disrupted oscillatory zoning in cathodoluminescence images, usually indicative of igneous origins and later metamorphism, respectively; most low-Ti grains are homogeneous. Several of each group display patchy zonation indicative of metamorphic overprinting. Although several grains with apparent Txlln >600°C display oscillatory zonation, the majority of the low-Ti group do not show textural evidence for igneous origins. We interpret these results to indicate the transition from a mechanism(s) that produced dominantly 680°C apparent zircon temperatures at ca. 3.9 Ga to include a new zircon-forming process in the sediment source(s), likely a protracted period of metamorphism

  10. JackEx: The new digital manufacturing resource for optimization of Exoskeleton-based factory environments

    OpenAIRE

    Constantinescu, Carmen; Mureșan, Paul Cristian; Simon, Gabriel-Marian

    2016-01-01

    The employment of Exoskeletons for manual handling work in manufacturing industries aims at increased employment, productivity, safety and security at workplace. This paper highlights several challenges, current results and future steps of our work in optimization of Exoskeleton based factory environments. “JackEx” is the enhancement of the standard digital humanoid “Jack” with concepts and elements of passive Exoskeletons. For the development of JackEx, a new digital manufacturing resource, ...

  11. Lawrence Livermore National Laboratory (LLNL) Experimental Test Site (Site 300) Salinity Evaluation and Minimization Plan for Cooling Towers and Mechanical Equipment Discharges

    Energy Technology Data Exchange (ETDEWEB)

    Daily III, W D

    2010-02-24

    This document was created to comply with the Central Valley Regional Water Quality Control Board (CVRWQCB) Waste Discharge Requirement (Order No. 98-148). This order established new requirements to assess the effect of and effort required to reduce salts in process water discharged to the subsurface. This includes the review of technical, operational, and management options available to reduce total dissolved solids (TDS) concentrations in cooling tower and mechanical equipment water discharges at Lawrence Livermore National Laboratory's (LLNL's) Experimental Test Site (Site 300) facility. It was observed that for the six cooling towers currently in operation, the total volume of groundwater used as make up water is about 27 gallons per minute and the discharge to the subsurface via percolation pits is 13 gallons per minute. The extracted groundwater has a TDS concentration of 700 mg/L. The cooling tower discharge concentrations range from 700 to 1,400 mg/L. There is also a small volume of mechanical equipment effluent being discharged to percolation pits, with a TDS range from 400 to 3,300 mg/L. The cooling towers and mechanical equipment are maintained and operated in a satisfactory manner. No major leaks were identified. Currently, there are no re-use options being employed. Several approaches known to reduce the blow down flow rate and/or TDS concentration being discharged to the percolation pits and septic systems were reviewed for technical feasibility and cost efficiency. These options range from efforts as simple as eliminating leaks to implementing advanced and innovative treatment methods. The various options considered, and their anticipated effect on water consumption, discharge volumes, and reduced concentrations are listed and compared in this report. Based on the assessment, it was recommended that there is enough variability in equipment usage, chemistry, flow rate, and discharge configurations that each discharge location at Site 300

  12. Lawrence Livermore National Laboratory (LLNL) Experimental Test Site (Site 300) Salinity Evaluation and Minimization Plan for Cooling Towers and Mechanical Equipment Discharges

    International Nuclear Information System (INIS)

    Daily, W.D. III

    2010-01-01

    This document was created to comply with the Central Valley Regional Water Quality Control Board (CVRWQCB) Waste Discharge Requirement (Order No. 98-148). This order established new requirements to assess the effect of and effort required to reduce salts in process water discharged to the subsurface. This includes the review of technical, operational, and management options available to reduce total dissolved solids (TDS) concentrations in cooling tower and mechanical equipment water discharges at Lawrence Livermore National Laboratory's (LLNL's) Experimental Test Site (Site 300) facility. It was observed that for the six cooling towers currently in operation, the total volume of groundwater used as make up water is about 27 gallons per minute and the discharge to the subsurface via percolation pits is 13 gallons per minute. The extracted groundwater has a TDS concentration of 700 mg/L. The cooling tower discharge concentrations range from 700 to 1,400 mg/L. There is also a small volume of mechanical equipment effluent being discharged to percolation pits, with a TDS range from 400 to 3,300 mg/L. The cooling towers and mechanical equipment are maintained and operated in a satisfactory manner. No major leaks were identified. Currently, there are no re-use options being employed. Several approaches known to reduce the blow down flow rate and/or TDS concentration being discharged to the percolation pits and septic systems were reviewed for technical feasibility and cost efficiency. These options range from efforts as simple as eliminating leaks to implementing advanced and innovative treatment methods. The various options considered, and their anticipated effect on water consumption, discharge volumes, and reduced concentrations are listed and compared in this report. Based on the assessment, it was recommended that there is enough variability in equipment usage, chemistry, flow rate, and discharge configurations that each discharge location at Site 300 should be

  13. A Group Interview about Publishing with Professor Jack Zipes

    Directory of Open Access Journals (Sweden)

    Emma Louise Parfitt

    2016-10-01

    Full Text Available The conversation piece is the product of a group interview with Professor Jack Zipes and provides useful insights about publishing for early career researchers across disciplines. Based on his wider experiences as academic and writer, Professor Zipes answered questions from PhD researchers about: writing books, monographs and edited collections; turning a PhD thesis into a monograph; choosing and approaching publishers; and the advantages of editing books and translations. It presents some general advice for writing and publishing aimed at postgraduate students. Professor Zipes is an Emeritus Professor at the University of Minnesota Twin Cities, United States, a world expert on fairy tales and storytelling highlighting the social and historical dimensions of them. Zipes has forty years of experience publishing academic and mass-market books, editing anthologies, and translating work from French, German and Italian. His best known books are Breaking the Magic Spell (1979, Fairy Tales and the Art of Subversion (1983, The Irresistible Fairy Tale: The Cultural and Social History of a Genre (2012, and The Original Folk and Fairy Tales of the Brothers Grimm (2014.

  14. Rearrangement of the layout of the welding equipment of a company in the metal mechanical sector using the Systematic Layout Planning method (SLP

    Directory of Open Access Journals (Sweden)

    Silvio Alexsandro Turati

    2016-06-01

    Full Text Available The correct physical layout is relevant to the operational efficiency of the company. This study proposes rearranging the layout of the welding equipment of a company in the metal mechanical sector, which is located in Araras/SP, aiming to improve the production workflow. The Systematic Layout Planning method (SLP was used, with the field research divided into steps: obtaining detailed information about the process and the product; meetings with stakeholders; determining inter-related activities; analyzing space requirements; developing a new layout. The new layout has space allocated for the purchasing of new machinery, the existing machinery has been redistributed by specialty, and the unloading of raw materials has been transferred to the shed, maximizing the use of overhead cranes and keeping the stock close to the warehouse. In addition, forklift traffic flow has decreased; new movement corridors were demarcated; and painting areas were isolated. In conclusion, the SLP method proved efficient in creating a layout.

  15. The structure and physical-mechanical properties of the heat-resistant Ni-Co-Cr-Al-Y intermetallic coating obtained using rebuilt plasma equipment

    Science.gov (United States)

    Tarasenko, Yu. P.; Tsareva, I. N.; Berdnik, O. B.; Fel, Ya. A.; Kuzmin, V. I.; Mikhalchenko, A. A.; Kartaev, E. V.

    2014-12-01

    Results of a study of the structure, physico-mechanical properties, and the resistance to heat of Ni-Co-Cr-Al-Y intermetallic coatings obtained by powder spraying on the standard UPU-3D plasma spray facility (plasmatron with self-establishing arc length) and on the rebuilt facility equipped with the enhanced-power PNK-50 plasmatron with sectionalized inter-electrode insert, are reported. Coatings of higher density ( ρ = 7.9 g/cm3) and higher microhardness (H μ = 770 kg-force/mm2) with lower porosity values ( P = 5.7 %, P c = 5.1 %, and P 0 = 0.6 %) and high resistance to heat ((M - M0)/M0 = 1.2) were obtained. The developed coating is intended for protection of the working surfaces of turbine engine blades in gas-turbine power plants.

  16. Using Jack Tales in a Second Grade Class.

    Science.gov (United States)

    Brown, Doris

    1987-01-01

    Describes a project in which Kentucky second grades developed puppet shows and photography activities based on traditional Appalachian oral tales. Discusses student progress in language arts skills, creativity, use of audiovisual equipment, and group cooperation. (SV)

  17. New equipment for mechanization of warehouse operations and its use in Donbass timber yards and material stores. Novoe oborudovanie dlya mekhanizatsii skladskikh rabot i opyt ego primeneniya na lesnykh i materialinykh skladakh Donbassa

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    Constructional features and characteristics of new warehouse equipment are described which were developed by Donetsk Scientific Research Coal Institute in cooperation with other establishments. Experience is reviewed in the use of: turning platforms (PPG3); lifting-hoisting units (PTU); motor-hydraulic grab (MGK3M); fork-lift racks ZOD; complex KLT for mechanization of operations in timber yards; chain conveyors (T2Ts); cyclone bunkers; preparation of support timber (sawing units PRK, SRT); devices for packing and conveying timber, concrete and other materials; equipment for warehouses (racks UN, UP, KB) and others. The equipment is widely used in UkSSR Minugleprom stores and provides safer working conditions.

  18. Analysis of Technical State of Thermal and Mechanical Equipment of Thermal Power Stations in the Republic of Belarus under Conditions of Investment Deficit

    Directory of Open Access Journals (Sweden)

    S. N. Shichko

    2004-01-01

    Full Text Available The paper contains an analysis of the equipment state at a number of thermal power stations. This analysis is made on the basis of indifferent curves. Relationship of two factors is taken as a criterion for estimation of the equipment state. These factors are faultiness (parameter of failure fi"equency and operating time from the moment when the equipment was put into operation. It is noted that operation of the equipment in excess of specified life without replacement of so-called «weab> elements and estimation of metal state will lead to conditions of high risk in opieration of such equipment.

  19. Black-tailed jack rabbit movements and habitat utilization at the Idaho National Engineering Laboratory radioactive waste management complex

    International Nuclear Information System (INIS)

    Grant, J.C.

    1983-01-01

    In June 1982, a study of black-tailed jack rabbit (Lepus californicus) ecology was initiated at the Idaho National Engineering Laboratory Radioactive Waste Management Complex (RWMC). This study will provide data necessary to evaluate the role of jack rabbits in radionuclide transport away from the Subsurface Disposal Area of the RWMC. Primary goals are to document radionuclide concentrations in jack rabbit tissues, and determine population size, movement patterns, habitat use, and food habits of jack rabbits inhabiting the RWMC area. Study design and prelimianry results are discussed

  20. Development of Universal Methodology of Specimen Free Nondestructive Inspection (Control) of Mechanical Properties of NPP Equipment Metal in all Stages of Lifetime

    International Nuclear Information System (INIS)

    Bakirov, M.; Chubarov, S.; Frolov, I.; Kiselev, I.; Gastrock, J.; Dripke, M.

    2011-01-01

    indications on tensile yield stress elevation due to hardening and also loss in ductility. The work-hardening index may be easily obtained, giving information on the ability of the material (e.g. pressure vessel steel and weld) to deform plastically without brittle fracture. Taking into account the experience of the Center of Material Science and Lifetime Management Ltd. (CMSLM Ltd.) in the use of methods of hardness testing for the inspection of the equipment of NPP of Russian manufacture in Russia, Germany, Czech, Slovakia, Bulgaria, and also similar successful works in this direction in USA (Oakridge), to Czech (NRI Rez) and other countries, it can be seen that the most promising direction in the field of specimen-free inspection of mechanical properties by use of hardness and hardness-related characteristics is use of the kinetic indentation method (KIM, ABIT). This method is based on recording the process of elastoplastic deformation caused by the indentation of a ball indenter. This method allows one to obtain, besides hardness values, tensile properties, elongation, work hardening coefficient, true-stress/true strain diagrammes which normally required the destructive testing of small specimens. However, till now there is no universal method of interpreting the information obtained, although it is generally known that irradiation causes a loss in ductility and increase in hardness and lowering of the work-hardening coefficient. Thus, it is necessary to develop a uniform methodology of using KIM, ABIT with reference to the inspection of materials which will allow unifying the inspection of materials of various classes of the equipment of NPP over all stages of life cycle. With the purpose of introduction of such a methodology it is necessary to develop and realize the program in the frames of IAEA with the above name. (author)

  1. An Analytical Method for Jack-Up Riser’s Fatigue Life Estimation

    Directory of Open Access Journals (Sweden)

    Fengde Wang

    2018-01-01

    Full Text Available In order to determine whether a special sea area and its sea state are available for the jack-up riser with surface blowout preventers, an analytical method is presented to estimate the jack-up riser’s wave loading fatigue life in this study. In addition, an approximate formula is derived to compute the random wave force spectrum of the small-scale structures. The results show that the response of jack-up riser is a narrow band random vibration. The infinite water depth dispersion relation between wavenumber and wave frequency can be used to calculate the wave force spectrum of small-scale structures. The riser’s response mainly consists of the additional displacement response. The fatigue life obtained by the formula proposed by Steinberg is less than that of the Bendat method.

  2. The Bildungsroman Tradition: The Philosophical Maturation of Jack Burden in All the King’s Men

    Directory of Open Access Journals (Sweden)

    Bassam M. Al-Shraah

    2017-11-01

    Full Text Available This paper aims to sketch out the transformation that Jack Burden—the main character in the novel—had gone through. With all the political leanings in Warren’s All the king’s Men, Jack burden seems to have had developed his own theories of dealing with life and people all through his life. He has always suffered an inferiority complex, rendering himself unworthy of being a real human being. This paper claims that Jack’s philosophical transformation has passed through three distinct phases; he had changed from a carefree idealist to a man of moral responsibility much similar to a Bildungsroman style of character maturation. Difficult times that Jack Burden has gone through caused his awakening at the end of the novel ushering his maturation

  3. Purification, crystallization and preliminary X-ray analysis of urease from jack bean (Canavalia ensiformis)

    International Nuclear Information System (INIS)

    Balasubramanian, Anuradha; Ponnuraj, Karthe

    2009-01-01

    Jack bean urease was purified and crystallized and X-ray diffraction data were collected to 2.05 Å resolution. Plant urease is a seed protein that is common in most legumes. It is also common in many bacteria and fungi and several species of yeast. Urease allows organisms to use exogenous and internally generated urea as a nitrogen source by catalyzing the hydrolysis of urea to ammonia and carbon dioxide. Urease from jack bean meal was purified to electrophoretic homogeneity using a series of steps involving acetone precipitation and size-exclusion and ion-exchange chromatography. The jack bean urease was crystallized and the resulting crystals diffracted to 2.05 Å resolution using synchrotron radiation. The crystals belonged to the hexagonal space group P6 3 22, with unit-cell parameters a = b = 138.57, c = 198.36 Å

  4. Spin-singlet quantum Hall states and Jack polynomials with a prescribed symmetry

    International Nuclear Information System (INIS)

    Estienne, Benoit; Bernevig, B. Andrei

    2012-01-01

    We show that a large class of bosonic spin-singlet Fractional Quantum Hall model wavefunctions and their quasihole excitations can be written in terms of Jack polynomials with a prescribed symmetry. Our approach describes new spin-singlet quantum Hall states at filling fraction ν=(2k)/(2r-1) and generalizes the (k,r) spin-polarized Jack polynomial states. The NASS and Halperin spin-singlet states emerge as specific cases of our construction. The polynomials express many-body states which contain configurations obtained from a root partition through a generalized squeezing procedure involving spin and orbital degrees of freedom. The corresponding generalized Pauli principle for root partitions is obtained, allowing for counting of the quasihole states. We also extract the central charge and quasihole scaling dimension, and propose a conjecture for the underlying CFT of the (k,r) spin-singlet Jack states.

  5. Chair in mechanical equipment in the mining industry and geotechnics at Clausthal Technological University; Professur fuer maschinelle Betriebsmittel in Bergbau und Geotechnik an der TU Clausthal

    Energy Technology Data Exchange (ETDEWEB)

    Langefeld, O.; Bergmann, O. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. fuer Bergbau

    2002-10-10

    The aim of this chair at the Institute for Mining at Clausthal Technological University is to familiarise the future engineer with the state of the art in the field of mechanical equipment. The main emphasis of the teaching is in particular the description of coal-mining and roadheading machines as well as conveying and storage technology. In the field of research basic investigations are currently being conducted on flexible bulk material containers, on determination of heat characteristics of insulating and construction materials as well as development of direct methanol fuel cells. (orig.) [German] Den zukuenftigen Ingenieur mit dem Stand der Technik im Bereich der maschinellen Betriebsmittel vertraut zu machen, ist das Ziel dieser Professur des Instituts fuer Bergbau an der TU Clausthal. Schwerpunkte der Lehre sind insbesondere die Darstellung von Gewinnungs- und Vortriebsmaschinen sowie die Foerder- und Lagertechnik. Auf dem Gebiet der Forschung werden zur Zeit Grundlagenuntersuchungen an flexiblem Schuettgutbehaeltern, an der Ermittlung waermetechnischer Kennwerte von Isolier- und Baustoffen sowie die Entwicklung von Direkten Methanolbrennstoffzellen betrieben. (orig.)

  6. [Hydrotherapy equipment].

    Science.gov (United States)

    Tsibikov, V B; Ragozin, S I; Mikheeva, L V

    1985-01-01

    A flow-chart is developed demonstrating the relation between medical and prophylactic institutions within the organizational structure of the rehabilitation system and main types of rehabilitation procedures. In order to ascertain the priority in equipping rehabilitation services with adequate hardware the special priority criterion is introduced. The highest priority is assigned to balneotherapeutic and fangotherapeutic services. Based on the operation-by-operation analysis of clinical processes related to service and performance of balneologic procedures the preliminary set of clinical devices designed for baths, basins and showers in hospitals and rehabilitation departments is defined in a generalized form.

  7. Estudo da impressão plantar obtida durante o teste de Jack em crianças Footprint study in children during the Jack test

    Directory of Open Access Journals (Sweden)

    José Antonio Pinto

    2011-01-01

    Full Text Available OBJETIVO: Avaliar as impressões plantares durante o teste de Jack em crianças quantificando e observando os resultados numa faixa etária crítica para a formação do arco plantar. MÉTODO: Avaliamos 60 crianças brancas (120 pés sendo 35 meninos e 25 meninas com idades entre 2 e 5 anos, sem queixas ortopédicas. Simulamos o teste de Jack com uma órtese em cunha de 45º apoiada sob o hálux. Obtivemos impressões em apoio monopodálico bilateralmente utilizando um pedígrafo. O exame dividiu-se em duas etapas: com e sem o uso da órtese. A metodologia de Valenti e Volpon foi utilizada para mensurar as impressões plantares e os dados obtidos foram analisados estatisticamente. RESULTADOS: Os valores dos índices de Valenti e Volpon diminuiram quando a órtese foi utilizada. A diferença entre os índices com ou sem órtese diminuiu gradualmente com a progressão etária. CONCLUSÕES: É possível quantificar o teste de Jack pelwas impressões plantares pelo método de Valenti e Volpon. A variação do seu formato apresentou tendência a ser menor a partir dos 4 anos. O teste de Jack perdeu gradativamente a capacidade de modificar a impressão plantar com a idade, diminuindo sua acuidade como parâmetro de bom prognóstico na formação do arco longitudinal medial. Nível de Evidência: Nível IV, estudo descritivo observacional.OBJECTIVE: To assess the plantar impressions obtained in children during the Jack test, with the aim of quantifying and analyzing their variability in the critical period for plantar foot arch formation. METHOD: A hundred and twenty feet from 60 healthy White children, recruited in an outpatient pediatric clinic, were examined. Our sample included 35 boys and 25 girls, ranging from 2 to 5 years. The Jack test was simulated using a 45o wedge-shaped orthosis applied to the hallux. Bilateral plantar impressions were acquired in the alternate single-foot standing position using a pedigraph. Two plantar impressions were

  8. Jack Michael's Musings on the 60th Anniversary of Skinner's "Verbal Behavior"

    Science.gov (United States)

    Esch, Barbara E.; Esch, John W.; Palmer, David C.

    2017-01-01

    When the B. F. Skinner Foundation reprinted Skinner's "Verbal Behavior" in 1992, Jack Michael wrote one of its two forewords, a detailed outline of the book's purpose and scope. On the 60th anniversary of the first publication (1957) of "Verbal Behavior", Jack reflects on the book's impact and its importance to the…

  9. Structure and biomass production of one- to seven-year-old intensively cultured jack pine plantation in Wisconsin.

    Science.gov (United States)

    J. Zavitkovski; David H. Dawson

    1978-01-01

    Spacing and rotation length effects were studied for 7 years in intensively cultured jack pine stands. Production culminated at age 5 in the densest planting and progressively later in more open spacing. Biomass production was two to several times higher than in jack pine plantations grown under traditional silvicultural systems.

  10. Cryogenic equipment

    International Nuclear Information System (INIS)

    Leger, L.; Javellaud, J.; Caro, C.; Gilguy, R.; Testard, O.

    1966-06-01

    The cryostats presented here were built from standard parts; this makes it possible to construct a great variety of apparatus at minimum cost. The liquid nitrogen and helium reservoirs were designed so as to reduce losses to a minimum, and so as to make the cryostats as autonomous as possible. The experimental enclosure which is generally placed in the lower part of the apparatus requires a separate study in every case. Furthermore, complete assemblies such as transfer rods, isolated traps and high vacuum valves, were designed with a similar regard for the economic aspects and for the need for standardization. This equipment thus satisfies a great variety of experimental needs; it is readily adaptable and the consumptions of helium and liquid nitrogen are very low. (authors) [fr

  11. Hi-Jack: a novel computational framework for pathway-based inference of host–pathogen interactions

    KAUST Repository

    Kleftogiannis, Dimitrios A.

    2015-03-09

    Motivation: Pathogens infect their host and hijack the host machinery to produce more progeny pathogens. Obligate intracellular pathogens, in particular, require resources of the host to replicate. Therefore, infections by these pathogens lead to alterations in the metabolism of the host, shifting in favor of pathogen protein production. Some computational identification of mechanisms of host-pathogen interactions have been proposed, but it seems the problem has yet to be approached from the metabolite-hijacking angle. Results: We propose a novel computational framework, Hi-Jack, for inferring pathway-based interactions between a host and a pathogen that relies on the idea of metabolite hijacking. Hi-Jack searches metabolic network data from hosts and pathogens, and identifies candidate reactions where hijacking occurs. A novel scoring function ranks candidate hijacked reactions and identifies pathways in the host that interact with pathways in the pathogen, as well as the associated frequent hijacked metabolites. We also describe host-pathogen interaction principles that can be used in the future for subsequent studies. Our case study on Mycobacterium tuberculosis (Mtb) revealed pathways in human-e.g. carbohydrate metabolism, lipids metabolism and pathways related to amino acids metabolism-that are likely to be hijacked by the pathogen. In addition, we report interesting potential pathway interconnections between human and Mtb such as linkage of human fatty acid biosynthesis with Mtb biosynthesis of unsaturated fatty acids, or linkage of human pentose phosphate pathway with lipopolysaccharide biosynthesis in Mtb. © The Author 2015. Published by Oxford University Press. All rights reserved.

  12. Jack Mezirow's Conceptualisation of Adult Transformative Learning: A Review

    Science.gov (United States)

    Calleja, Colin

    2014-01-01

    This paper traces the evolution of Jack Mezirow's transformative learning theory and its conceptualisation. It discusses the three major influences, namely Thomas Khun's philosophical conception of paradigm, Freire's conception of conscientisation and consciousness growth, and Habermas' domains of learning and the discussion of…

  13. "Delays and Vexation": Jack London and the Russo-Japanese War.

    Science.gov (United States)

    Sweeney, Michael S.

    1998-01-01

    Contributes to scholarship on journalism history and censorship by discussing Jack London's efforts as a war correspondent to cover the Russo-Japanese War in Korea and Manchuria in 1904. Focuses on the difficulties he encountered as a result of systematic and highly restrictive censorship by the Japanese. (SR)

  14. Height and seasonal growth pattern of jack pine full-sib families

    Science.gov (United States)

    Don E. Riemenschneider

    1981-01-01

    Total tree height, seasonal shoot elongation, dates of growth initiation and cessation, and mean daily growth rate were measured and analyzed for a population of jack pine full-sib families derived from inter-provenance crosses. Parental provenance had no effect on these variables although this may have been due to small sample size. Progenies differed significantly...

  15. Asymptotic theory of generalized estimating equations based on jack-knife pseudo-observations

    DEFF Research Database (Denmark)

    Overgaard, Morten; Parner, Erik Thorlund; Pedersen, Jan

    2017-01-01

    A general asymptotic theory of estimates from estimating functions based on jack-knife pseudo-observations is established by requiring that the underlying estimator can be expressed as a smooth functional of the empirical distribution. Using results in p-variation norms, the theory is applied...

  16. Pandemic Fear and Literature: Observations from Jack London’s The Scarlet Plague

    Centers for Disease Control (CDC) Podcasts

    2014-11-18

    Sarah Gregory reads an abridged version of the essay, Pandemic Fear and Literature: Observations from Jack London’s The Scarlet Plague.  Created: 11/18/2014 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 11/20/2014.

  17. Mosaic Stunting in jack pine seedlings in a northern Michigan bareroot nursery

    Science.gov (United States)

    Lynette Potvin; R. Kasten Dumroese; Martin F. Jurgensen; Dana Richter

    2010-01-01

    Mosaic, or patchy, stunting of bareroot conifer seedlings is thought to be caused by deficiencies of mycorrhizal fungi following fumigation, resulting in reduced nutrient uptake, particularly phosphorus. Mosaic stunting of jack pine (Pinus banksiana) seedlings was observed in 2005 at the USDA Forest Service JW Toumey Nursery in Watersmeet, MI. We initiated a study to...

  18. Habitat Preferences, Distribution Pattern, and Root Weight Estimation of Pasak Bumi (Eurycoma longifolia Jack.

    Directory of Open Access Journals (Sweden)

    Siti Masitoh Kartikawati

    2014-04-01

    Full Text Available Pasak bumi (Eurycoma longifolia Jack is one of non timber forest products with “indeterminate” conservation status and commercially traded in West Kalimantan. The research objective was to determine the potential of pasak bumi root per hectare and its ecological condition under natural habitat. Root weight of E. longifolia Jack was estimated using simple linear regression and exponential equation with stem diameter and height as independent variables. The results showed that the individual number of the population was 114 with the majority in seedling stage with 71 individuals (62.28%. The distribution was found in clumped pattern. Conditions of the habitat could be described as follows: daily average temperature of 25.6oC, daily average relative humidity of 73.6%, light intensity of 0.9 klx, and red-yellow podsolic soil with texture ranged from clay to sandy clay. The selected estimator model for E. longifolia Jack root weight used exponential equation with stem height as independent variable using the equation of Y= 21.99T0,010 and determination coefficient of 0.97. After height variable was added, the potential of E. longifolia Jack minimum root weight that could be harvested per hectare was 0.33 kg.Keywords: Eurycoma longifolia, habitat preference, distribution pattern, root weight

  19. Lithium in Jack Hills zircons: Evidence for extensive weathering of Earth's earliest crust

    Science.gov (United States)

    Ushikubo, Takayuki; Kita, Noriko T.; Cavosie, Aaron J.; Wilde, Simon A.; Rudnick, Roberta L.; Valley, John W.

    2008-08-01

    In situ Li analyses of 4348 to 3362 Ma detrital zircons from the Jack Hills, Western Australia by SIMS reveal that the Li abundances (typically 10 to 60 ppm) are commonly over 10,000 times higher than in zircons crystallized from mantle-derived magmas and in mantle-derived zircon megacrysts (typically Jack Hills zircons also have fractionated lithium isotope ratios ( δ7Li = - 19 to + 13‰) about five times more variable than those recorded in primitive ocean floor basalts (2 to 8‰), but similar to continental crust and its weathering products. Values of δ7Li below - 10‰ are found in zircons that formed as early as 4300 Ma. The high Li compositions indicate that primitive magmas were not the source of Jack Hills zircons and the fractionated values of δ7Li suggest that highly weathered regolith was sampled by these early Archean magmas. These new Li data provide evidence that the parent magmas of ancient zircons from Jack Hills incorporated materials from the surface of the Earth that interacted at low temperature with liquid water. These data support the hypothesis that continental-type crust and oceans existed by 4300 Ma, within 250 million years of the formation of Earth and the low values of δ7Li suggest that weathering was extensive in the early Archean.

  20. Jacks-of-all-trades? The effect of balanced skills on team performance

    NARCIS (Netherlands)

    Rosendahl Huber, L.; Sloof, R.; van Praag, M.

    2014-01-01

    Previous empirical studies have shown that solo entrepreneurs benefit from having balanced skills: Jacks-of-All-Trades (JATs) are better entrepreneurs than specialists are. Nowadays however, the majority of entrepreneurs start up and run ventures together in teams. In this paper we test whether the

  1. Impacts of fiber orientation and milling on observed crystallinity in jack pine

    Science.gov (United States)

    Umesh P. Agarwal; Sally A. Ralph; Richard S. Reiner; Roderquita K. Moore; Carlos Baez

    2014-01-01

    Influences of fiber orientation and milling on wood cellulose crystallinity were studied using jack pine wood. The fiber orientation effects were measured by sampling rectangular wood blocks in radial, tangential, and cross-sectional orientations. The influence of milling was studied by analyzing the unsieved and sieved milled wood fractions (all

  2. Uus valem otsustamiseks: 10-10-10 / Jack Welch, Suzy Welch

    Index Scriptorium Estoniae

    Welch, Jack

    2009-01-01

    Juhtimisspetsialistid Jack ja Suzy Welch tutvustavad enda loodud valemit 10-10-10, mis on elu juhtimise tööriist aitamaks langetada raskeid otsuseid, hinnates nende mõju 10 minuti, 10 kuu ja 10 aasta pärast

  3. 3-D habitat suitability of jack mackerel Trachurus murphyi in the Southeastern Pacific, a comprehensive study

    NARCIS (Netherlands)

    Bertrand, A.; Habasque, J.; Hattab, Tarek; Hintzen, N.T.; Ricardo, Oliveros Ramos; Gutierrez, M.; Demarcq, Herve; Gerlotto, F.

    2016-01-01

    South Pacific jack mackerel, Trachurus murphyi, has an ocean-scale distribution, from the South American coastline to New Zealand and Tasmania. This fish, captured by Humans since the Holocene, is nowadays heavily exploited and its population has decreased substantially since the mid-1990s. The

  4. Soil loss by water erosion in areas under maize and jack beans intercropped and monocultures

    Directory of Open Access Journals (Sweden)

    Pedro Luiz Terra Lima

    2014-04-01

    Full Text Available Adequate soil management can create favorable conditions to reduce erosion and water runoff, consequently increase water soil recharge. Among management systems intercropping is highly used, especially for medium and small farmers. It is a system where two or more crops with different architectures and vegetative cycles are explored simultaneously at the same location. This research investigated the effects of maize intercropped with jack bean on soil losses due to water erosion, estimate C factor of Universal Soil Losses Equation (USLE and how it can be affected by soil coverage. The results obtained also contribute to database generation, important to model and estimate soil erosion. Total soil loss by erosion caused by natural rain, at Lavras, Minas Gerais, Brazil, were: 4.20, 1.86, 1.38 and 1.14 Mg ha-1, respectively, for bare soil, maize, jack bean and the intercropping of both species, during evaluated period. Values of C factor of USLE were: 0.039, 0.054 and 0.077 Mg ha Mg-1 ha-1 for maize, jack bean and intercropping between both crops, respectively. Maize presented lower vegetation cover index, followed by jack beans and consortium of the studied species. Intercropping between species showed greater potential on soil erosion control, since its cultivation resulted in lower soil losses than single crops cultivation, and this aspect is really important for small and medium farmers in the studied region.

  5. Pivoting output unit control systems activated by jacks. [for controlling aircraft flaps

    Science.gov (United States)

    Belliere, P.

    1978-01-01

    An invention to be used for controlling aircraft flaps is described. It is applicable to control systems with two coaxial output units which pivot simultaneously with respect to two fixed units and which are activated by two opposed, straight coaxial jacks.

  6. Jack Nicholson: A Reel and Real-Life Contribution to Neurosciences.

    Science.gov (United States)

    Tripathi, Manjul; Purkayastha, Moushumi; Rai, Ashutosh; Mukherjee, Kanchan K

    2017-05-01

    Though primarily considered entertainment, cinema is a mirror of society. The portrayal of neurosciences is common in cinema, but none could do it better than Jack Nicholson. We give a brief overview of his contribution to neurosciences by analyzing his acting skills. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Constituents of the essential oils of Cinnamomum parthenoxylon (Jack) Nees from Vietnam

    NARCIS (Netherlands)

    Dung, N.X.; Moi, La Dinh; Hung, N.D.; Leclercq, P.A.

    1995-01-01

    The essential oils obtained by steam distillation of the root bark and wood of Cinnamomum parthenoxylon (Jack) Nees growing wild in Vietnam were investigated by a combination of GC and GC/MS. More than 30 compounds in the root bark oil, and about 20 components in the wood oil have been identified.

  8. Cadmium accumulation by jack-bean and sorghum in hydroponic culture.

    Science.gov (United States)

    Francato Zancheta, Ariana Carramaschi; De Abreu, Cleide Aparecida; Zambrosi, Fernando César Bachiega; de Magalhães Erismann, Norma; Andrade Lagôa, Ana Maria Magalhães

    2015-01-01

    Among the technologies used to recuperate cadmium (Cd) contaminated soils, phytoextraction are particularly important, where the selection of suitable plants is critical to the success of the soil remediation. Thus, the objectives of this study were to evaluate the responses of jack-bean and sorghum to Cd supply and to quantify Cd accumulation by these species grown in hydroponic culture. The plants were subjected to 0, 15, 30, or 60 μmol Cd L(-1) in the nutrient solution, and gas exchange, plant growth and Cd accumulation were measured at 25 days after starting Cd treatments. The Cd supply severely reduced growth of shoots and roots in both species. In jack-bean, Cd decreased photosynthesis by 56-86%, stomatal conductance by 59-85% and transpiration by 48-80%. The concentrations and amounts of Cd accumulated in the plant tissues were proportional to the metal supply in the nutrient solution. Sorghum was more tolerant than jack-bean to Cd toxicity, but the latter showed a greater metal concentration and accumulation in the shoot. Therefore, jack-bean would be more suitable than sorghum for use in Cd phytoremediation programs based on phytoextraction.

  9. IDENTIFIKASI METABOLIT SEKUNDER DAN AKTIVITAS ANTIBAKTERI EKSTRAK DAUN SUNGKAI (Peronema canescens JACK. TERHADAP BEBERAPA BAKTERI PATOGEN

    Directory of Open Access Journals (Sweden)

    Arsyik Ibrahim

    2012-12-01

    Full Text Available A research which identification of secondary metabolites and antibacterial activity test from methanol exstract of leaf Sungkai (Peronema canencens Jack to several pathogens bacterial, which aims to identification of secondary methabolites and determine the antibacterial activity from crude methanol extract of leaf Sungkai (P. canencens Jack. against Streptococcus mutans, Salmonella thyposa, Bacillus subtilis and Staphylococcus aureus bacteria. Material test obtained by maceration with methanol, then tested for activity. Minimum Inhibition Concentration (MIC value extract was determined by liquid dilution and the followed by scratches on solid media method.  Minimum Kill Concentration (KBM value extracts was determined by agar diffusion method with using paper disks.The results secondary metabolite identify form extracts of leaves P. canencens obtainable derived alkaloid, terpenoids - steroids, flavonoids, and tannin compounds. Methanol extract have the antibacterial activity. Minimum Inhibition Concentration (MIC value of extract is concentration of 20% for bacteria S. mutans, S.thiposa and S.aureus, while for the B. subtilis is konsentration of 15%. Minimum Kill Concentration (KBM values exstract at a concentration of 5% effective at killing S. mutans and S. thyposa bacteria, while the concentration of 1% effective to bacteria B.subtilis and S.aureus. Key words: P. canencens Jack,  antibacteria activity, S. mutans, S. thiposa, B. subtillis, S. aureus   ABSTRAK   Telah dilakukan penelitian identifikasi metabolit sekunder dan aktivitas antibakteri ekstrak metanol daun Sungkai (P.canencens Jack terhadap beberapa bakteri patogen. Penelitian ini bertujuan untuk mengidentifikasi metabolit sekunder dan mengetahui aktifitas antibakteri dan Kadar Hambat Minimum (KHM dan Nilai Kadar Bunuh Minimum (KBM ekstrak kasar metanol daun Sungkai (P.canencens Jack. terhadap bakteri  Streptococcus mutans, Salmonella thyposa, Bacillus subtilis dan

  10. An expedient synthesis of N-(1-(5-mercapto-4-((substituted benzylidene)amino)-4H-1,2,4-triazol-3-yl)-2-phenylethyl)benzamides as jack bean urease inhibitors and free radical scavengers: Kinetic mechanism and molecular docking studies.

    Science.gov (United States)

    Saeed, Aamer; Larik, Fayaz Ali; Channar, Pervaiz Ali; Mehfooz, Haroon; Ashraf, Mohammad Haseeb; Abbas, Qamar; Hassan, Mubashir; Seo, Sung-Yum

    2017-11-01

    In this study, some new azomethine-triazole hybrids 5a-5l derived from N-benzoyl-L-phenylalanine were synthesized and characterized. The synthesized compounds showed first-rate, urease inhibition, and compounds 5c and 5e were found to be most effective inhibitors with 0.0137 ± 0.00082 μm and 0.0183 ± 0.00068 μm, respectively (thiourea 15.151 ± 1.27 μm). The kinetic mechanism of urease inhibition revealed the compounds 5c and 5e to be non-competitive inhibitors, whereas compounds 5d and 5j were found to be of mixed-type inhibitors. Docking studies also indicated better interaction patterns with urease enzyme. The results of enzyme inhibition, kinetic mechanism and molecular docking suggest that these compounds can serve as lead compounds in the design of more effective urease inhibitors. © 2017 John Wiley & Sons A/S.

  11. Practical application of the benchmarking technique to increase reliability and efficiency of power installations and main heat-mechanic equipment of thermal power plants

    Science.gov (United States)

    Rimov, A. A.; Chukanova, T. I.; Trofimov, Yu. V.

    2016-12-01

    facilitating the analysis of the benchmarking results permitting to represent the quality loss of this power installation in the form of the difference between the actual value of the key indicator or comparison indicator and the best quartile of the existing distribution. The uncertainty of the obtained values of the quality loss indicators was evaluated by transforming the standard uncertainties of the input values into the expanded uncertainties of the output values with the confidence level of 95%. The efficiency of the technique is demonstrated in terms of benchmarking of the main thermal and mechanical equipment of the extraction power-generating units T-250 and power installations of the thermal power plants with the main steam pressure 130 atm.

  12. Medical Issues: Equipment

    Science.gov (United States)

    ... Information Packets Equipment Pool Living With SMA Medical Issues Palliative Breathing Orthopedics Nutrition Equipment Daily Life At ... curesma.org > support & care > living with sma > medical issues > equipment Equipment Individuals with SMA often require a ...

  13. Semiconductor Manufacturing equipment introduction

    International Nuclear Information System (INIS)

    Im, Jong Sun

    2001-02-01

    This book deals with semiconductor manufacturing equipment. It is comprised of nine chapters, which are manufacturing process of semiconductor device, history of semiconductor manufacturing equipment, kinds and role of semiconductor manufacturing equipment, construction and method of semiconductor manufacturing equipment, introduction of various semiconductor manufacturing equipment, spots of semiconductor manufacturing, technical elements of semiconductor manufacturing equipment, road map of technology of semiconductor manufacturing equipment and semiconductor manufacturing equipment in the 21st century.

  14. Scientific Equipment Division - Overview

    International Nuclear Information System (INIS)

    Halik, J.

    2001-01-01

    Full text: The Scientific Equipment Division consists of the Design Group and the Mechanical Workshop. The activity of the Division includes the following: - designing of devices and equipment for experiments in physics, their mechanical construction and assembly. In particular, there are vacuum chambers and installations for HV and UHV; - maintenance and upgrading of the existing installations and equipment in our Institute; - participation of our engineers and technicians in design works, equipment assembly and maintenance for experiments in foreign laboratories. The Design Group is equipped with PC-computers and AutoCAD graphic software (release 2000 and Mechanical Desktop 4.0) and a AO plotter, what allows us to make drawings and 2- and 3-dimensional mechanical documentation to the world standards. The Mechanical Workshop can offer a wide range of machining and treatment methods with satisfactory tolerances and surface quality. It offers the following possibilities: - turning - cylindrical elements of a length up to 2000 mm and a diameter up to 400 mm, and also disc-type elements of a diameter up to 600 mm and a length not exceeding 300 mm; - milling - elements of length up to 1000 mm and gear wheels of diameter up to 300 mm; - grinding - flat surfaces of dimensions up to 300 mm x 1000 mm and cylindrical elements of a diameter up to 200 mm and a length up to 800 mm; - drilling - holes of a diameter up to 50 mm; - welding - electrical and gas welding, including TIG vacuum-tight welding; - soft and hard soldering; - mechanical works including precision engineering; - plastics treatment - machining and polishing using diamond milling, modelling, lamination of various shapes and materials, including plexiglas, scintillators and light-guides; - painting - paint spraying with possibility of using furnace-fred drier of internal dimensions of 800 mm x 800 mm x 800 mm. Our workshop posses CNC milling machine which can be used for machining of work-pieces up to 500 kg

  15. Southwestern Surgical Congress Jack A. Barney award competition presenters - Where are they now?

    Science.gov (United States)

    Kothari, Shanu N; Kallies, Kara J

    2017-12-01

    Resident research presentations at surgical conferences may encourage future research endeavors. 2010-2016 SWSC annual meeting programs were reviewed for presenters eligible for the Jack Barney award. Award recipients from 1987 to 2016 were included. There were 100 unique presenters eligible for the Jack Barney award, and 28 unique award recipients. Thirty-six (82%) presenters currently practice in a community setting, 5 (11%) at a university hospital, 2 (5%) internationally, and 1 (2%) in a military hospital. Scholarly articles were published by 41% of presenters. Sixteen of the 28 recipients (57%) practice in community hospitals, and 9 (32%) practice in university settings; 3 are still in training. Twenty recipients (71%) published after residency. Thirty percent and 25% of presenters and recipients are SWSC members, respectively. Peer-reviewed publications were frequent among eligible presenters and award recipients. Encouraging presenters to become SWSC members provides an opportunity for improved retention. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Cluster analysis on a sphere: Application to magnetizations from metasediments of the Jack Hills, Western Australia

    Science.gov (United States)

    Bono, Richard K.; Tarduno, John A.; Dare, Matthew S.; Mitra, Gautam; Cottrell, Rory D.

    2018-02-01

    Metasediments of the Jack Hills contain the oldest known terrestrial minerals in the form of zircons nearly 4.4 billion years old. Paleointensity data from these zircons provide evidence for a Hadean geodynamo as old as 4.2 billion years old. Given the importance of these zircons for constraining the earliest history of the core, it is vital to understand the fidelity of the zircon record. A fundamental aspect providing context for the preservation of primary magnetic signals is the nature of overprints predicted to have been imparted on rocks of the Jack Hills due to Archean to Proterozoic metamorphic events. To be viable magnetic records of a Hadean geodynamo, zircon magnetization directions should differ from these secondary magnetizations. To evaluate these secondary magnetizations, we report paleomagnetic analyses of a comprehensive sampling of 68 quartzite cobble-sized clasts from the Jack Hills metasediments ∼0.5 to 1.0 km from the Discovery Site (which has yielded the oldest zircons and paleofield estimates). While application of standard paleomagnetic tests suggests that the ensemble of cobble directions cannot be distinguished from those drawn from a random distribution, a new cluster analysis of directions on a sphere and non-parametric resampling approaches reveal significant directions amongst subsets of the data. One, isolated at the lowest temperature analyzed [200 to 300 °C, Declination (Dec.) = 316.8°, Inclination (Inc.) = - 51.1 °] appears to be dominated by the present day field. Another, isolated at higher (but still relatively low unblocking temperatures that we call "intermediate", of ∼350-500 °C, Dec. = 243.8°, Inc. = 9.5°) agrees with a magnetic overprint isolated from the secondary Cr-Fe mica fuchsite isolated from the Jack Hills Discovery site, passing a field test at the 80% confidence level. No evidence is found in our data, or in the data of others collected on similar Jack Hills lithologies, for a widespread 1 Ga

  17. JackIn Head: Immersive Visual Telepresence System with Omnidirectional Wearable Camera.

    Science.gov (United States)

    Kasahara, Shunichi; Nagai, Shohei; Rekimoto, Jun

    2017-03-01

    Sharing one's own immersive experience over the Internet is one of the ultimate goals of telepresence technology. In this paper, we present JackIn Head, a visual telepresence system featuring an omnidirectional wearable camera with image motion stabilization. Spherical omnidirectional video footage taken around the head of a local user is stabilized and then broadcast to others, allowing remote users to explore the immersive visual environment independently of the local user's head direction. We describe the system design of JackIn Head and report the evaluation results of real-time image stabilization and alleviation of cybersickness. Then, through an exploratory observation study, we investigate how individuals can remotely interact, communicate with, and assist each other with our system. We report our observation and analysis of inter-personal communication, demonstrating the effectiveness of our system in augmenting remote collaboration.

  18. Historical wildlife dynamics on Dugway Proving Ground: population and disease trends in jack rabbits over two decades. [Lepus californicus

    Energy Technology Data Exchange (ETDEWEB)

    Eberhardt, L.E.; Van Voris, P.

    1986-08-01

    In an effort to determine whether US Army activities on the Dugway Proving Ground (DPG) have had an impact on resident wildlife, intensive studies have been conducted on the biology and ecology of the black-tailed jack rabbit (Lepus californicus) since 1965. in addition, the incidence of endemic diseases in several species of resident wildlife on the DPG have been studied from the late 1950s through the mid-1970s. The objectives of this report are to: (1) compile and summarize the jack rabbit data and some of the disease information that is presently contained only in annual reports; (2) compare the DPG jack rabbit data to data available on other jack rabbit populations; and (3) analyze the data for unusual or unexplained fluctuations in population densities or in incidence of disease.

  19. Seismic analysis of the frame structure reformed by cutting off column and jacking based on stiffness ratio

    Science.gov (United States)

    Zhao, J. K.; Xu, X. S.

    2017-11-01

    The cutting off column and jacking technology is a method for increasing story height, which has been widely used and paid much attention in engineering. The stiffness will be changed after the process of cutting off column and jacking, which directly affects the overall seismic performance. It is usually necessary to take seismic strengthening measures to enhance the stiffness. A five story frame structure jacking project in Jinan High-tech Zone was taken as an example, and three finite element models were established which contains the frame model before lifting, after lifting and after strengthening. Based on the stiffness, the dynamic time-history analysis was carried out to research its seismic performance under the EL-Centro seismic wave, the Taft seismic wave and the Tianjin artificial seismic wave. The research can provide some guidance for the design and construction of the entire jack lifting structure.

  20. In Search of the Real Mr. China Jack Perkowski's positive account of his business adventures in China

    Institute of Scientific and Technical Information of China (English)

    MATTHEW PLOWRIGHT

    2008-01-01

    @@ When former Wall Street banker Jack Perkowski first arrived in Hong Kong in 1990 looking to set up a business, not only did he not speak a word of the language, he had never even tasted Chinese food.

  1. Eesti saab 2018. aasta Londoni raamatumessil erilise tähelepanu osaliseks / Jacks Thomas ; intervjueerinud Priit Hõbemägi

    Index Scriptorium Estoniae

    Thomas, Jacks

    2017-01-01

    Intervjuu Euroopa ühe suurima, Londoni raamatumessi direktori Jacks Thomasiga, kes külastas Tallinna, et teha ettevalmistusi järgmiseks aastaks, kui Eesti koos teiste Baltimaadega on messi peakülaline

  2. Railway crossings: driving the structure under the railway by means of oleodinamic jacks

    OpenAIRE

    Escribano Méndez, Ramón; López Palomar, Rafael; Ruiz Viedma, Andrés J.

    1991-01-01

    "The best level crossing is a dead crossing", those involved are accustomed to say Yet, until a short time ago, eliminating these conflictive crossings not only implied a great deal of money but prolonged building work, with the all too familiar sequel of precautions, speed restrictions and problems for rail traffic. However, a brand new system, based on using hydraulic jacks to drive the concrete structure of the crossing to a different level in the track embankment, allows the execution in ...

  3. The Jack Wills crowd: towards a sociology of an elite subculture.

    Science.gov (United States)

    King, Anthony; Smith, Daniel

    2018-03-01

    British sociologists have long been interested in youth sub-cultures. However British sociologists have tended to focus on working class subcultures and avoided engagement with exclusive sub-cultures of elite social groups. This article seeks to attend to this gap by examining the subculture of a British elite: ex-public school students at select universities in the UK in the twenty-first century. This group consists of a relatively small group of young adults, aged between 18 and 23, who attended public schools, especially one of the nine Clarendon schools (Eton, Winchester, Westminster, St. Paul's, Merchant Taylor's, Shrewsbury, Rugby, Harrow and Charterhouse), and were students at a selective group of British universities, primarily Oxford and Cambridge, Durham, Bristol, Exeter, Bath, Manchester, St Andrews and Edinburgh. The article examines the way in which this group has reconfigured and re-constituted itself in the face of globalizing challenges. Specifically, it examines the way in which participation of ex-public school students in events run by and under the patronage of the high street retailing company, Jack Wills, has played a galvanising role for this group in the last decade. The Jack Wills crowd is an example of how some young adults form exclusive social networks and reproduce prevailing forms of privilege. The social networks built around the Jack Wills subculture is likely to provide them with advantages in the job market through a prodigious network of connections and patrons. The Jack Wills subculture potentially contributions to the socio-economic reproduction of the higher professional middle classes. © London School of Economics and Political Science 2017.

  4. Rereading "The Jack-Roller:" Hidden Histories in Sociology and Social Work

    Science.gov (United States)

    Shaw, Ian

    2009-01-01

    I revisit one of the iconic Chicago School studies, Clifford Shaw's "The Jack-Roller". A naive reading of Shaw's book leaves the reader with a sense of having been inducted into a melange of what we now know as "sociology" and "social work," but which to Shaw seems a coherent stance. I suggest that this is close to the heart of how things were,…

  5. Effect of slaughter methods on the quality of Chilean jack mackerel (Trachurus murphyi) during refrigerated storage.

    Science.gov (United States)

    Lyu, Fei; Huang, Rui-Ji; Liu, Lin; Zhou, Xuxia; Ding, Yu-Ting

    2015-03-01

    The main objective of this study was to assess the influence of slaughter methods on the quality of Chilean jack mackerel (Trachurus murphyi) during refrigerated storage on board. Fishes were slaughtered by asphyxia in air (AA), asphyxia in ice water (AI) or stunning fish heads (SH), and the rigor mortis, pH, total volatile basic nitrogen (TVB-N), trimethylamine (TMA), 2-thiobarbituric acid reactive substances (TBARS) and sensory properties for the fishes were analyzed. On day 0, Chilean jack mackerel samples of AI group displayed higher pH values than those of AA and SH groups. TVB-N, TMA and TBARS values of all samples increased with the storage time, and these values of AI had a lower increase than AA and SH. Moreover, samples of AI had a better sensory score than AA and SH during storage. It can be concluded that slaughter method of asphyxia in ice water for Chilean jack mackerel exhibit the better efficiency on maintaining the fish quality during refrigerated storage on board.

  6. Variation of Time Domain Failure Probabilities of Jack-up with Wave Return Periods

    Science.gov (United States)

    Idris, Ahmad; Harahap, Indra S. H.; Ali, Montassir Osman Ahmed

    2018-04-01

    This study evaluated failure probabilities of jack up units on the framework of time dependent reliability analysis using uncertainty from different sea states representing different return period of the design wave. Surface elevation for each sea state was represented by Karhunen-Loeve expansion method using the eigenfunctions of prolate spheroidal wave functions in order to obtain the wave load. The stochastic wave load was propagated on a simplified jack up model developed in commercial software to obtain the structural response due to the wave loading. Analysis of the stochastic response to determine the failure probability in excessive deck displacement in the framework of time dependent reliability analysis was performed by developing Matlab codes in a personal computer. Results from the study indicated that the failure probability increases with increase in the severity of the sea state representing a longer return period. Although the results obtained are in agreement with the results of a study of similar jack up model using time independent method at higher values of maximum allowable deck displacement, it is in contrast at lower values of the criteria where the study reported that failure probability decreases with increase in the severity of the sea state.

  7. Commissioning and maintenance experience on mechanical equipment in steam generators of captive power plant at HWP, Manuguru (Paper No. 5.3)

    International Nuclear Information System (INIS)

    Bhatnagar, R.; Sinha, Ashok; Mohan Rao, A.C.

    1992-01-01

    Heavy Water Project (Manuguru) is having a captive power plant to cater to the demands of steam and power for the main plant. During the commissioning and initial run of the steam generators and their auxiliaries, teething/initial problems were encountered in nearly all the equipment of the steam generators. This paper briefly describes some of the major problems faced during the commissioning of the steam generators. (author). 4 figs

  8. Selection of equipment for equipment qualification

    International Nuclear Information System (INIS)

    Torr, K.G.

    1989-01-01

    This report describes the methodology applied in selecting equipment in the special safety systems for equipment qualification in the CANDU 600 MW nuclear generating stations at Gentilly 2 and Point Lepreau. Included is an explanation of the selection procedure adopted and the rationale behind the criteria used in identifying the equipment. The equipment items on the list have been grouped into three priority categories as a planning aid to AECB staff for a review of the qualification status of the special safety systems

  9. Jack Polynomials as Fractional Quantum Hall States and the Betti Numbers of the ( k + 1)-Equals Ideal

    Science.gov (United States)

    Zamaere, Christine Berkesch; Griffeth, Stephen; Sam, Steven V.

    2014-08-01

    We show that for Jack parameter α = -( k + 1)/( r - 1), certain Jack polynomials studied by Feigin-Jimbo-Miwa-Mukhin vanish to order r when k + 1 of the coordinates coincide. This result was conjectured by Bernevig and Haldane, who proposed that these Jack polynomials are model wavefunctions for fractional quantum Hall states. Special cases of these Jack polynomials include the wavefunctions of Laughlin and Read-Rezayi. In fact, along these lines we prove several vanishing theorems known as clustering properties for Jack polynomials in the mathematical physics literature, special cases of which had previously been conjectured by Bernevig and Haldane. Motivated by the method of proof, which in the case r = 2 identifies the span of the relevant Jack polynomials with the S n -invariant part of a unitary representation of the rational Cherednik algebra, we conjecture that unitary representations of the type A Cherednik algebra have graded minimal free resolutions of Bernstein-Gelfand-Gelfand type; we prove this for the ideal of the ( k + 1)-equals arrangement in the case when the number of coordinates n is at most 2 k + 1. In general, our conjecture predicts the graded S n -equivariant Betti numbers of the ideal of the ( k + 1)-equals arrangement with no restriction on the number of ambient dimensions.

  10. Impact of the cosmetic mouthwash “Jack Pro Spülung plus” (“rheodol-Spülung plus” on the oral cavity flora, tested in a monocentric, controlled, randomized, blind, cross-over comparative study

    Directory of Open Access Journals (Sweden)

    Göhring, Jana

    2014-03-01

    Full Text Available [english] Aim: Jack Pro Spülung Plus (also available as “rheodol-Spülung plus” is recommended to mechanically maintain oral hygiene as part of an overall oral hygiene concept. Because Jack Pro Spülung Plus contains the active agents polihexanide and tosylchloramide sodium in concentrations below microbicidal efficacy, this study tested the hypothesis that the combination of mechanical rinsing and bacteriostatic effect surpasses the effect of mechanical rinsing alone.Method: The study was performed with 30 volunteers as a monocentric, controlled, randomized, blind, cross-over comparative study. The efficacy of the test product (active agents polihexanide 0.02–0.03% and tosylchloramide sodium 0.004–0.006% was compared to an aqueous solution of polihexanide (0.02–0.03% and to Ringer solution as negative control. The efficacy was measured as the reduction of colony forming units (cfu on buccal mucosa after aerobic and anaerobic cultivation. After determination of pre-values, the volunteers performed mouthrinsing for 30 sec with each of the 3 tested solutions. After 1, 10 and 60 minutes, cfu numbers were determined again. The reduction factor was calculated as the difference between log of the measured cfu before and after mouthrinsing with the test solution. The sampling was performed using a template with a smear area of 1 x 1 cm. Results: Using Ringer solution led to a slight mechanically-induced reduction of cfu in the oral cavity 1 min after rinsing the mouth cavity with the solution. After 10 min and 60 min, no influence on the cfu number could be detected. Using Jack pro Spülung Plus led to a bacteriostatic effect up to 60 min after mouthrinsing; 10 min and 60 min after rinsing the efficacy of Ringer solution was also significantly surpassed. The aqueous solution of polihexanide was less effective than Jack pro Spülung Plus after 10 and 60 min. Conclusion: Based on these observations, we conclude that Jack pro Spülung Plus is

  11. Determining the effect of different cooking methods on the nutritional composition of salmon (Salmo salar and chilean jack mackerel (Trachurus murphyi fillets.

    Directory of Open Access Journals (Sweden)

    José M Bastías

    Full Text Available The effect of four cooking methods was evaluated for proximate composition, fatty acid, calcium, iron, and zinc content in salmon and Chilean jack mackerel. The moisture content of steamed salmon decreased (64.94% compared to the control (68.05%; a significant decrease was observed in Chilean jack mackerel in all the treatments when compared to the control (75.37%. Protein content in both salmon and Chilean jack mackerel significantly increased under the different treatments while the most significant decrease in lipids was found in oven cooking and canning for salmon and microwaving for Chilean jack mackerel. Ash concentration in both salmon and Chilean jack mackerel did not reveal any significant differences. Iron and calcium content only had significant changes in steaming while zinc did not undergo any significant changes in the different treatments. Finally, no drastic changes were observed in the fatty acid profile in both salmon and Chilean jack mackerel.

  12. Determining the effect of different cooking methods on the nutritional composition of salmon (Salmo salar) and chilean jack mackerel (Trachurus murphyi) fillets

    Science.gov (United States)

    Balladares, Pamela; Acuña, Sergio; Quevedo, Roberto; Muñoz, Ociel

    2017-01-01

    The effect of four cooking methods was evaluated for proximate composition, fatty acid, calcium, iron, and zinc content in salmon and Chilean jack mackerel. The moisture content of steamed salmon decreased (64.94%) compared to the control (68.05%); a significant decrease was observed in Chilean jack mackerel in all the treatments when compared to the control (75.37%). Protein content in both salmon and Chilean jack mackerel significantly increased under the different treatments while the most significant decrease in lipids was found in oven cooking and canning for salmon and microwaving for Chilean jack mackerel. Ash concentration in both salmon and Chilean jack mackerel did not reveal any significant differences. Iron and calcium content only had significant changes in steaming while zinc did not undergo any significant changes in the different treatments. Finally, no drastic changes were observed in the fatty acid profile in both salmon and Chilean jack mackerel. PMID:28686742

  13. The Effect of Water Limitation on Volatile Emission, Tree Defense Response, and Brood Success of Dendroctonus ponderosae in Two Pine Hosts, Lodgepole, and Jack Pine

    OpenAIRE

    Lusebrink, Inka; Erbilgin, Nadir; Evenden, Maya L.

    2016-01-01

    The mountain pine beetle (MPB; Dendroctonus ponderosae) has recently expanded its range from lodgepole pine forest into the lodgepole × jack pine hybrid zone in central Alberta, within which it has attacked pure jack pine. This study tested the effects of water limitation on tree defense response of mature lodgepole and jack pine (Pinus contorta and Pinus banksiana) trees in the field. Tree defense response was initiated by inoculation of trees with the MPB-associated fungus Grosmannia clavig...

  14. Validation of on-site job-built guardrails with shoring jack as supports

    Directory of Open Access Journals (Sweden)

    Lan, A.

    2014-06-01

    Full Text Available To protect themselves against fall hazards in a slab-column frame, workers use the row of shoring jacks installed at 1 m from the edge as supports for on-site built guardrails. Inspectors of the Quebec Workers Compensation Board (Commission de la santé et de la sécurité du travail (CSST have expressed concern about the safety and compliance of these on-site built guardrails with the Quebec Safety Code for the Construction Industry (S-2.1, r.4. Some workers have also inquired if the shoring jack can be used as an anchor for a travel restraint system. The present study describes how an evaluation method and a test protocol have been used to verify if guardrails built on-site, with shoring jacks as supports, are safe and comply with the requirements of S-2.1, r.4 and if the shoring jack can be used as an anchor point for a travel restraint system. The results of the study show 1 guardrails built on site with shoring jacks as supports, are safe and comply with S-2.1, r.4 and 2 shoring jacks used as supports for guardrails must not be used as an anchor for a travel restraint system.Para la protección contra el peligro de caída en altura durante la ejecución de la estructura de un edificio, los trabajadores utilizan puntales acodalados a dos forjados y situados a 1 metro del borde de forjado como apoyo de las barandillas de seguridad. Inspectores de la Quebec Workers Compensation Board (Commision de la santé et de la sécurité du travail (CSST han expresado su preocupación por la seguridad y el cumplimiento de estos sistemas de protección en la construcción conforme al Código de Seguridad de Quebec para la industria de la construcción (S-2.1, R.6. Así mismo algunos trabajadores han mostrado su inquietud sobre la utilización de los puntales como sistemas para limitar el desplazamiento. El presente estudio describe un método de evaluación y un procedimiento de ensayo que se han utilizado para verificar si las barandillas de seguridad

  15. The Cholesterol Lowering Effects of Eurycoma longifolia Jack (Tongkat Ali Root Extract in Male Rats

    Directory of Open Access Journals (Sweden)

    Ghasak G Faisal

    2017-04-01

    Full Text Available Background: To investigate the effect of Eurycoma longifolia Jack root extract on serum lipids in rats. Methods: Twenty-six mature male albino Wistar rats were used in this study. A group of 18 rats were fed a high fat and high cholesterol diet for 4 weeks, after which their lipid profile was compared to the control group, who were kept on a normal diet. The rats were then further divided into three groups, the Cf group that continued to feed on a high fat and cholesterol diet only, and group A and group B who continued on a high fat diet with the addition of 5 mg/kg and 10 mg/kg of Eurycoma longifolia Jack root extract respectively for 4 weeks. After the 4 week period, the rat's lipid profiles were analysed again. Results: Group A and B showed significant total cholesterol reduction when compared to the Cf group, 140 ± 7.23, 139.63 ± 7.95, 192.14 ± 8.96 mg/dL respectively (p < 0.001. The total cholesterol/HDL ratio in group A was 5 however there was a sharp increase in group B to a high-risk level of 9.2 indicating a significant drop in HDL levels. The LDL level increased significantly in both group A and B compared to the Cf group. Conclusions: Eurycoma longifolia Jack root extract is effective in lowering total cholesterol, however the dose needs to be adjusted to prevent an excessive decrease in HDL levels.

  16. Secondary vegetation succession on jack pine (Pinus banksiana) cutovers in northeastern Ontario, Canada

    Energy Technology Data Exchange (ETDEWEB)

    Tiveau, Daniel

    2000-07-01

    The effects of different harvesting and site preparation methods on competing vegetation were studied in nine jack pine (Pinus banksiana) cutovers in northeastern Ontario, Canada. Six different treatments plus glyphosate herbiciding and no herbiciding were applied: 1) tree-length harvesting followed by trenching, and full-tree harvesting followed by five site preparations, 2) no site preparation, 3) trenching and 4) blading and compaction as well as blading followed by two planting densities, 5) 1.2m and 6) 2m. Competing vegetation was assessed preharvest and years 1, 2, 3, and 5 postharvest. Data was also available from nine juvenile sites as well as nine semimature sites. Data collection consisted of coverage values of each species as well as structural data for main life forms in height classes. Growth and health data of the planted jack pine seedlings were also available. The data was analyzed using detrended correspondence analysis (DCA), diversity indices and tabular analysis. Three years after the herbicide application there is no difference between the total coverage in the halfplots that have received herbiciding and those that have not, but an alteration of the relative abundance of species groups has developed; glyphosate herbiciding promotes grasses over shrubs. When no site preparation is applied, shrubs increase and compete with the seedlings, whose growth is cut in half compared to the ones that have been site prepared by trenching. Five years after blading, and blading plus compaction, there is still very little vegetation in the research plots, but there is no reduction of the survival rate and growth of the jack pine seedlings. More dense planting after this treatment leads to more competing vegetation, probably due to increased availability of moisture. Grasses do not seem to be affected by compaction and pioneer mosses are promoted by this treatment but compaction leads to a significant reduction of the total coverage of competing vegetation

  17. A sperm-agglutinating lectin from seeds of Jack fruit (Artocarpus heterophyllus).

    Science.gov (United States)

    Namjuntra, P; Muanwongyathi, P; Chulavatnatol, M

    1985-04-30

    A lectin specific for N-acetylgalactosamine was isolated from seed extract of Jack fruit (Artocarpus heterophyllus) by ammonium sulfate precipitation, followed by affinity chromatography on a Affigel-galactosamine-agarose column. The lectin possessed agglutinating activities for human and rat sperm as well as human red blood cells. It was found to have Mr = 62,000 consisting of two dissimilar subunits of Mr = 18,000 and 13,000. It also cross-reacted with an antibody against the lectin of Osage Orange (Maclura pomifera).

  18. Selected Problems of Sensitivity and Reliability of a Jack-Up Platform

    Directory of Open Access Journals (Sweden)

    Rozmarynowski Bogdan

    2018-03-01

    Full Text Available The paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The sudy aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized eigenvalue problem and evaluation of the performace functions. The first order time-invariant problems of structural reliability analysis are under concern.

  19. A phyt osociological classification of the vegetation of the Jack Scott Nature Reserve*

    Directory of Open Access Journals (Sweden)

    B. J. Coetzee

    1974-12-01

    Full Text Available The vegetation of the Jack Scott Nature Reserve in the Central Bankenveld Veld Type is classified chiefly by the Braun-Blanquet Table Method. Habitat features, physiognomy, total floristic composition, differentiating species, woody plants and prominent grasses and forbs are presented for each community. Characterizing habitat features, in order of importance for the communities, are: exposure, soil texture, geology, slope, aspect, degree of rockiness and previous ploughing. The classification correlates well with the major physiographic and climatic variation in the Reserve and generally does not cut across main physiognomic types. The communities are potentially homogeneous management units.

  20. Narrativa visual de uma obra beat: os vagabundos iluminados de Jack Kerouac

    OpenAIRE

    TEJERO MARTINEZ, DIANA MARIA

    2014-01-01

    Este trabajo analiza las técnicas narrativas de los "cómics" aplicadas en la adaptación de la novela "Los vagabundos del Dharma" de Jack Kerouac. Se trata de un trabajo de investigación basado en los estudios de los teóricos Will Eisner y Scott McCloud y de la estudiosa de la adaptación Linda Hutcheon. En la inverstigación se exploran las posibilidades de los "cómics" como medio de expressión gráfica y las características de las adaptaciones de algunas obras...

  1. A Comparison Between Measured and Predicted Hydrodynamic Damping for a Jack-Up Rig Model

    DEFF Research Database (Denmark)

    Laursen, Thomas; Rohbock, Lars; Jensen, Jørgen Juncher

    1996-01-01

    An extensive set of measurements funded by the EU project Large Scale Facilities Program has been carried out on a model of a jack-up rig at the Danish Hydraulic Institute. The test serieswere conducted by MSC and include determination of base shears and overturning moments in both regular...... methods.In the comparison between the model test results and the theoretical predictions, thehydro-dynamic damping proves to be the most important uncertain parameter. It is shown thata relative large hydrodynamic damping must be assumed in the theoretical calculations in orderto predict the measured...

  2. Acheronta movebo. Resilencia y revolución en The Mexican (1911 de Jack London

    Directory of Open Access Journals (Sweden)

    Eduardo González de la Fuente

    2016-07-01

    Full Text Available Este artículo maneja uno de los relatos pugilísticos de Jack London, The Mexican (1911, para explorar el mundo del boxeo como lugar público de conflictos sociales e ideológicos identificados y significados en la proteica figura del boxeador. Así pues, el ring es susceptible de devenir y analizarse como un espacio de práctica política, de antagonismo y debate que, en su reglada exposición de violencias carnales y simbólicas, condensa una particular síntesis efectiva de corporalidades y discursos.

  3. Protective equipment use among female rugby players.

    Science.gov (United States)

    Comstock, R Dawn; Fields, Sarah K; Knox, Christy L

    2005-07-01

    Our objective was to assess the prevalence of protective equipment use and the motivation for using protective equipment among a sample of US female rugby players. We surveyed a convenience sample of 234 current US female rugby players from 14 teams participating in a US women's rugby tournament, obtaining self-reported demographic, rugby exposure, and protective equipment use information. Mouthguards were the most commonly used piece of protective equipment: 90.8% of players reported having always worn a mouthguard while playing or practicing rugby within their most recent 3 months of play. Fewer than 15% of players reported having always worn other types of protective equipment. Equipment use varied by playing position. Whereas over 80% of players in all other positions always wore a mouthguard, 66.7% of scrum halves reported always wearing one. Both backs and forwards reported wearing shoulder pads, but only forwards reported always wearing padded headgear. Mouthguards, padded headgear, and shoulder pads were worn "to prevent injury," whereas ankle braces, neoprene sleeves, and athletic tape on joints were worn "to protect a current/recent injury." This is the first study of female rugby players to assess the prevalence of protective equipment use by playing position and the motivation for using protective equipment. With the exception of mouthguards, US female rugby players infrequently use protective equipment. Protective equipment use varies by playing position. Some types of protective equipment appear to be used as primary prevention mechanisms, whereas others are used as secondary or tertiary prevention mechanisms.

  4. The effect of water limitation on volatile emission, tree defense response, and brood success of Dendroctonus ponderosae in two pine hosts, lodgepole and jack pine

    Directory of Open Access Journals (Sweden)

    Inka eLusebrink

    2016-02-01

    Full Text Available The mountain pine beetle (MPB; Dendroctonus ponderosae has recently expanded its range from lodgepole pine forest into the lodgepole × jack pine hybrid zone in central Alberta, within which it has attacked pure jack pine. This study tested the effects of water limitation on tree defense response of mature lodgepole and jack pine (Pinus contorta and Pinus banksiana trees in the field. Tree defense response was initiated by inoculation of trees with the MPB-associated fungus Grosmannia clavigera and measured through monoterpene emission from tree boles and concentration of defensive compounds in phloem, needles, and necrotic tissues. Lodgepole pine generally emitted higher amounts of monoterpenes than jack pine; particularly from fungal-inoculated trees. Compared to non-inoculated trees, fungal inoculation increased monoterpene emission in both species, whereas water treatment had no effect on monoterpene emission. The phloem of both pine species contains (--α-pinene, the precursor of the beetle’s aggregation pheromone, however lodgepole pine contains two times as much as jack pine. The concentration of defensive compounds was 70-fold greater in the lesion tissue in jack pine, but only 10-fold in lodgepole pine compared to healthy phloem tissue in each species, respectively. Water-deficit treatment inhibited an increase of L-limonene as response to fungal inoculation in lodgepole pine phloem. The amount of myrcene in jack pine phloem was higher in water-deficit trees compared to ambient trees. Beetles reared in jack pine were not affected by either water or biological treatment, whereas beetles reared in lodgepole pine benefited from fungal inoculation by producing larger and heavier female offspring. Female beetles that emerged from jack pine bolts contained more fat than those that emerged from lodgepole pine, even though lodgepole pine phloem had a higher nitrogen content than jack pine phloem. These results suggest that jack pine chemistry

  5. Cross-Reactivity of Polyclonal Antibodies against Canavalia ensiformis (Jack Bean) Urease and Helicobacter pylori Urease Subunit A Fragments.

    Science.gov (United States)

    Kaminski, Zbigniew Jerzy; Relich, Inga; Konieczna, Iwona; Kaca, Wieslaw; Kolesinska, Beata

    2018-01-01

    Overlapping decapeptide fragments of H. pylori urease subunit A (UreA) were synthesized and tested with polyclonal antibodies against Canavalia ensiformis (Jack bean) urease. The linear epitopes of UreA identified using the dot blot method were then examined using epitope mapping. For this purpose, series of overlapping fragments of UreA, frameshifted ± four amino acid residues were synthesized. Most of the UreA epitopes which reacted with the Jack bean urease polyclonal antibodies had been recognized in previous studies by monoclonal antibodies against H. pylori urease. Fragments 11 - 24, 21 - 33, and 31 - 42 were able to interact with the Jack bean urease antibodies, giving stable immunological complexes. However, the lack of recognition by these antibodies of all the components in the peptide map strongly suggests that a non-continuous (nonlinear) epitope is located on the N-terminal domain of UreA. © 2018 Wiley-VHCA AG, Zurich, Switzerland.

  6. Influence of mycorrhizal associations on paper birch and jack pine seedlings when exposed to elevated copper, nickel or aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Jones, M.D.; Browning, M.H.R.; Hutchinson, T.C.

    1986-10-01

    Acid deposition may adversely affect northern forest ecosystems by increasing the concentration of metals in the soil solution. This study investigates the effects of ectomycorrhizal fungi on paper birch and jack pine seedlings exposed to elevated Cu, Ni or Al in sand culture. One of four mycorrhizal fungi, Scleroderma flavidum, was able to reduce Ni toxicity to the birch seedlings. It did this by reducing transport of Ni to the stems. None of the fungi affected Cu toxicity in birch. In separate experiments, jack pine seedlings were exposed to combinations of Al and Ca. Infection with Rhizopogon rubescens increased seedling susceptibility to Al. Seedlings inoculated with Suillus tomentosus showed a greater growth stimulation by Ca than uninoculated jack pines. Thus, for both tree species, the mycorrhizal association could alter the response of seedlings to high concentrations of certain metals, although this varied with fungal species. 8 references.

  7. Manuka honey (Leptospermum scoparium) inhibits jack bean urease activity due to methylglyoxal and dihydroxyacetone.

    Science.gov (United States)

    Rückriemen, Jana; Klemm, Oliver; Henle, Thomas

    2017-09-01

    Manuka honey (Leptospermum scoparium) exerts a strong antibacterial effect. Bacterial enzymes are an important target for antibacterial compounds. The enzyme urease produces ammonia and enables bacteria to adapt to an acidic environment. A new enzymatic assay, based on photometric detection of ammonia with ninhydrin, was developed to study urease activity. Methylglyoxal (MGO) and its precursor dihydroxyacetone (DHA), which are naturally present in manuka honey, were identified as jack bean urease inhibitors with IC 50 values of 2.8 and 5.0mM, respectively. Urease inhibition of manuka honey correlates with its MGO and DHA content. Non-manuka honeys, which lack MGO and DHA, showed significantly less urease inhibition. MGO depletion from manuka honey with glyoxalase reduced urease inhibition. Therefore, urease inhibition by manuka honey is mainly due to MGO and DHA. The results obtained with jack bean urease as a model urease, may contribute to the understanding of bacterial inhibition by manuka honey. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Sneaker "jack" males outcompete dominant "hooknose" males under sperm competition in Chinook salmon (Oncorhynchus tshawytscha).

    Science.gov (United States)

    Young, Brent; Conti, David V; Dean, Matthew D

    2013-12-01

    In a variety of taxa, males deploy alternative reproductive tactics to secure fertilizations. In many species, small "sneaker" males attempt to steal fertilizations while avoiding encounters with larger, more aggressive, dominant males. Sneaker males usually face a number of disadvantages, including reduced access to females and the higher likelihood that upon ejaculation, their sperm face competition from other males. Nevertheless, sneaker males represent an evolutionarily stable strategy under a wide range of conditions. Game theory suggests that sneaker males compensate for these disadvantages by investing disproportionately in spermatogenesis, by producing more sperm per unit body mass (the "fair raffle") and/or by producing higher quality sperm (the "loaded raffle"). Here, we test these models by competing sperm from sneaker "jack" males against sperm from dominant "hooknose" males in Chinook salmon. Using two complementary approaches, we reject the fair raffle in favor of the loaded raffle and estimate that jack males were ∼1.35 times as likely as hooknose males to fertilize eggs under controlled competitive conditions. Interestingly, the direction and magnitude of this skew in paternity shifted according to individual female egg donors, suggesting cryptic female choice could moderate the outcomes of sperm competition in this externally fertilizing species.

  9. POPULASI DAN HABITAT Nepenthes ampullaria Jack. DI CAGAR ALAM MANDOR, KALIMANTAN BARAT

    Directory of Open Access Journals (Sweden)

    Maysarah .

    2017-04-01

    Full Text Available Nepenthes ampullaria Jack. is a species which adapted on the nutrient-poor areas in Mandor nature reserve.  Its could be increasing the quality of Mandor nature reserve as protected area. This research aims to study the population and habitat of N. ampullaria in the Mandor nature reserve. This study was conducted at two habitats, heath forest and peat swamp forest. Observations were made on, population abundance and habitat factors of  N. ampullaria. The results showed that the highest population density of N. ampullaria was in heath forest. Their are growth in groups. Vegetation analysis showed that constituent species habitat of N. ampullaria consist of 69 species from 39 familly. Result of identification to insects showed Formicidae is dominant family that trapped in pitcher of N. ampullaria. Temperature and humidity in N. ampullaria’s habitat has been switable for requirements growth of pitcher plant. Rainfall during the study was normally. Ratio of sand and soil on both affected the improvement of individual N. ampullaria in Mandor nature reserve. Keywords: habitat, Mandor nature reserve, Nepenthes ampullaria Jack, population

  10. The construction of identity in a consumerist society: Delillo’s Jack Gladney

    Directory of Open Access Journals (Sweden)

    Sanja Matković

    2016-02-01

    Full Text Available This paper deals with the construction of the postmodern identity of Jack Gladney, the main character in Don DeLillo’s White Noise (1985. Employing (postmodern, social psychology, and psychoanalytic theories of Zygmunt Bauman, Erich Fromm, Jean Baudrillard, and Gilles Lipovetsky, it analyzes the construction of Gladney’s character through his social roles as professor, husband, and consumer in the narrow sense of the word in order to deduce that his consumerist practices have spread to all aspects of his life. This reading reveals a new interpretation of Gladney’s fear of death; it shows that Gladney’s thanatophobia represents a consequence of his atheistic worldview. Namely, unable to find a haven in religion, he unsuccessfully seeks the meaning of life and death elsewhere, mainly in consumerism, which is identified as the source of his alienation from himself, people, and God. This paper suggests that numerous problems of postmodern life are caused by the lack of faith in God and proposes a conclusion that religion itself could be the answer to the difficulties faced by postmodern individuals with fragmented identities such as Jack Gladney.

  11. 30 CFR 77.410 - Mobile equipment; automatic warning devices.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Mobile equipment; automatic warning devices. 77... UNDERGROUND COAL MINES Safeguards for Mechanical Equipment § 77.410 Mobile equipment; automatic warning devices. (a) Mobile equipment such as front-end loaders, forklifts, tractors, graders, and trucks, except...

  12. Shipboard and laboratory equipment

    Digital Repository Service at National Institute of Oceanography (India)

    Shyamprasad, M.; Ramaswamy, V.

    The polymetallic nodules occur at an average depth of 4500 m. Adequate equipment and techniques are required for the exploration at such depths. Shipboard and various laboratory equipments for the sampling of polymetallic nodules is described...

  13. Remote handling equipment

    International Nuclear Information System (INIS)

    Clement, G.

    1984-01-01

    After a definition of intervention, problems encountered for working in an adverse environment are briefly analyzed for development of various remote handling equipments. Some examples of existing equipments are given [fr

  14. Exercise Equipment: Neutral Buoyancy

    Science.gov (United States)

    Shackelford, Linda; Valle, Paul

    2016-01-01

    Load Bearing Equipment for Neutral Buoyancy (LBE-NB) is an exercise frame that holds two exercising subjects in position as they apply counter forces to each other for lower extremity and spine loading resistance exercises. Resistance exercise prevents bone loss on ISS, but the ISS equipment is too massive for use in exploration craft. Integrating the human into the load directing, load generating, and motion control functions of the exercise equipment generates safe exercise loads with less equipment mass and volume.

  15. BP volume reduction equipment

    International Nuclear Information System (INIS)

    Kitamura, Yoshinori; Muroo, Yoji; Hamanaka, Isao

    2003-01-01

    A new type of burnable poison (BP) volume reduction system is currently being developed. Many BP rods, a subcomponent of spent fuel assemblies are discharged from nuclear power reactors. This new system reduces the overall volume of BP rods. The main system consists of BP rod cutting equipment, equipment for the recovery of BP cut pieces, and special transport equipment for the cut rods. The equipment is all operated by hydraulic press cylinders in water to reduce operator exposure to radioactivity. (author)

  16. Electric utility engineer`s FGD manual -- Volume 2: Major mechanical equipment; FGD proposal evaluations; Use of FGDPRISM in FGD system modification, proposal, evaluation, and design; FGD system case study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-04

    Part 2 of this manual provides the electric utility engineer with detailed technical information on some of the major mechanical equipment used in the FGD system. The objectives of Part 2 are the following: to provide the electric utility engineer with information on equipment that may be unfamiliar to him, including ball mills, vacuum filters, and mist eliminators; and to identify the unique technique considerations imposed by an FGD system on more familiar electric utility equipment such as fans, gas dampers, piping, valves, and pumps. Part 3 provides an overview of the recommended procedures for evaluating proposals received from FGD system vendors. The objectives are to provide procedures for evaluating the technical aspects of proposals, and to provide procedures for determining the total costs of proposals considering both initial capital costs and annual operating and maintenance costs. The primary objective of Part 4 of this manual is to provide the utility engineer who has a special interest in the capabilities of FGDPRISM [Flue Gas Desulfurization PRocess Integration and Simulation Model] with more detailed discussions of its uses, requirements, and limitations. Part 5 is a case study in using this manual in the preparation of a purchase specification and in the evaluation of proposals received from vendors. The objectives are to demonstrate how the information contained in Parts 1 and 2 can be used to improve the technical content of an FGD system purchase specification; to demonstrate how the techniques presented in Part 3 can be used to evaluate proposals received in response to the purchase specification; and to illustrate how the FGDPRISM computer program can be used to establish design parameters for the specification and evaluate vendor designs.

  17. Electrical equipment qualification

    International Nuclear Information System (INIS)

    Farmer, W.S.

    1983-01-01

    Electrical equipment qualification research programs being carried out by CEA, JAERI, and Sandia Laboratories are discussed. Objectives of the program are: (1) assessment of accident simulation methods for electrical equipment qualification testing; lower coarse (2) evaluation of equipment aging and accelerated aging methods; (3) determine radiation dose spectrum to electrical equipment and assess simulation methods for qualification; (4) identify inadequacies in electrical equipment qualification procedures and standards and potential failure modes; and (5) provide data for verifying and improving standards, rules and regulatory guides

  18. AVM branch vibration test equipment

    International Nuclear Information System (INIS)

    Anne, J.P.

    1995-01-01

    An inventory of the test equipment of the AVM Branch ''Acoustic and Vibratory Mechanics Analysis Methods'' group has been undertaken. The purpose of this inventory is to enable better acquaintance with the technical characteristics of the equipment, providing an accurate definition of their functionalities, ad to inform potential users of the possibilities and equipment available in this field. The report first summarizes the various experimental surveys conduced. Then, using the AVM equipment database to draw up an exhaustive list of available equipment, it provides a full-scope picture of the vibration measurement systems (sensors, conditioners and exciters) and data processing resources commonly used on industrial sites and in laboratories. A definition is also given of a mobile test unit, called 'shelter', and a test bench used for the testing and performance rating of the experimental analysis methods developed by the group. The report concludes with a description of two fixed installations: - the calibration bench ensuring the requisite quality level for the vibration measurement systems ; - the training bench, whereby know-how acquired in the field in the field of measurement and experimental analysis processes is made available to others. (author). 27 refs., 15 figs., 2 appends

  19. Ecological Responses to Five Years of Experimental Nitrogen Application in an Upland Jack-pine Stand

    Science.gov (United States)

    Melaschenko, N.; Berryman, S.; Straker, J.; Berg, K.; McDonough, A.; Watmough, S. A.

    2016-12-01

    A five-year experimental study was conducted to evaluate the response of an upland jack-pine (Pinus banksiana) forest to elevated levels of nitrogen (N) deposition in Northern Alberta. N deposition in the region is expected to increase with industrial expansion of oil sands activity, and there is regional interest to set N critical loads for sensitive ecosystems. In this study, N was applied as NH4NO3 above a jack-pine canopy via helicopter, annually for five years (2010-2015) at dosages equivalent to 5, 10, 15, 20 and 25 kg N ha-1 yr-1. Approximately 35% of the applied N was retained in the canopy while 65% reached understory vegetation dominated by lichens and mosses. We measured a significant increase in tissue N concentrations of common ground lichens (Cladonia mitis and C. stellaris) and ground moss (Pleurozium schreberi) as well as epiphytic lichens (Hypogymnia physodes and Evernia mesomorpha). On an annual basis, the applied N was primarily captured in the lichen and moss understory, dominated by C. mitis. In the highest treatments, N concentrations in C. mitis were 1.5-2.5 times greater than pre-treatment values. Peak N concentrations in the ground moss Pleurozium schreberi (1.4%) indicate that a threshold of N saturation was reached by year 3. We observed no changes in community composition of vascular and non-vascular plants, or changes in vascular plant tissue N. Chlorophyll levels in C. mitis increased with N treatment, but there was no indication of toxicity or changes to decomposition and growth. After five years of N application, only Peltigera polydactylon, a ground cyanolichen, appeared to be negatively impacted where the thalli showed necrosis at deposition loads >10kg N ha-1 yr-1. No changes to biomass or N ecosystem processes were observed. Based on these observations, we provide evidence that the first adverse ecological effects of N deposition in jack-pine stands occurred at deposition rates of 10 kg N ha-1 yr-1.

  20. Space Heating Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Rafferty, Kevin D.

    1998-01-01

    The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

  1. Renewal of radiological equipment.

    Science.gov (United States)

    2014-10-01

    In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

  2. Characterizing the physical and genetic structure of the lodgepole pine × jack pine hybrid zone: mosaic structure and differential introgression.

    Science.gov (United States)

    Cullingham, Catherine I; James, Patrick M A; Cooke, Janice E K; Coltman, David W

    2012-12-01

    Understanding the physical and genetic structure of hybrid zones can illuminate factors affecting their formation and stability. In north-central Alberta, lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia) and jack pine (Pinus banksiana Lamb) form a complex and poorly defined hybrid zone. Better knowledge of this zone is relevant, given the recent host expansion of mountain pine beetle into jack pine. We characterized the zone by genotyping 1998 lodgepole, jack pine, and hybrids from British Columbia, Alberta, Saskatchewan, Ontario, and Minnesota at 11 microsatellites. Using Bayesian algorithms, we calculated genetic ancestry and used this to model the relationship between species occurrence and environment. In addition, we analyzed the ancestry of hybrids to calculate the genetic contribution of lodgepole and jack pine. Finally, we measured the amount of gene flow between the pure species. We found the distribution of the pine classes is explained by environmental variables, and these distributions differ from classic distribution maps. Hybrid ancestry was biased toward lodgepole pine; however, gene flow between the two species was equal. The results of this study suggest that the hybrid zone is complex and influenced by environmental constraints. As a result of this analysis, range limits should be redefined.

  3. Healing of the Acutely Injured Anterior Cruciate Ligament: Functional Treatment with the ACL-Jack, a Dynamic Posterior Drawer Brace

    Directory of Open Access Journals (Sweden)

    Matthias Jacobi

    2016-01-01

    Full Text Available Background. The injured anterior cruciate ligament (ACL has a limited healing capacity leading to persisting instability. Hypothesis/Purpose. To study if the application of a brace, producing a dynamic posterior drawer force, after acute ACL injury reduces initial instability. Study Design. Cohort study. Methods. Patients treated with the ACL-Jack brace were compared to controls treated with primary ACL reconstruction und controls treated nonsurgically with functional rehabilitation. Measurements included anterior laxity (Rolimeter, clinical scores (Lysholm, Tegner, and IKDC, and MRI evaluation. Patients were followed up to 24 months. Results. Patients treated with the ACL-Jack brace showed a significant improvement of anterior knee laxity comparable to patients treated with ACL reconstruction, whereas laxity persisted after nonsurgical functional rehabilitation. The failure risk (secondary reconstruction necessary of the ACL-Jack group was however 21% (18 of 86 within 24 months. Clinical scores were similar in all treatment groups. Conclusion. Treatment of acute ACL tears with the ACL-Jack brace leads to improved anterior knee laxity compared to nonsurgical treatment with functional rehabilitation.

  4. Effect of average growing season temperature on seedling germination, survival and growth in jack pine (Pinus banksiana Lamb.)

    Science.gov (United States)

    A. David; E. Humenberger

    2017-01-01

    Because jack pine (Pinus banksiana Lamb.) is serotinous, it retains multiple years of cones until environmental conditions are favorable for releasing seed. These cones, which contain seed cohorts that developed under a variety of growing seasons, can be accurately aged using bud scale scars on twigs and branches. By calculating the average daily...

  5. Jack Michael's Appointments at the University of Houston and Arizona State University: Reflections from a Former Student

    Science.gov (United States)

    Mabry, John H.

    2016-01-01

    Jack Michael was an early enthusiast for what is now called applied behavior analysis. His many seminal contributions were through early publications in applied behavior analysis and the work of the students he trained (e.g., T. Ayllon, M. M. Wolf). His close mentorship of students earned him acclaim as a teacher along with his many theoretical…

  6. Raccoglier lettere. Le “Vico collaborations” di Jack W. Stauffacher e Dennis Letbetter

    Directory of Open Access Journals (Sweden)

    Armando, David

    2010-01-01

    Full Text Available Starting in the early ’70s the San Francisco printer and typographer Jack W. Stauffacher undertook a graphic exploration of Vico’s works, which continued during the past decade together with the photographer Dennis Letbetter. The aim of this article is to present their experience - which is at the same time poetic and historically attentive, focusing on the relationships between text and images, and on the typographical and physical qualities of 18th century editions - to an audience which includes Italian Vico scholars. The text is composed of a brief introduction and an interview with the two artists, and is followed (pp. 94-180 by a photographic presentation of their "Vico collaborations".

  7. Solving 1D plasmas and 2D boundary problems using Jack polynomials and functional relations

    International Nuclear Information System (INIS)

    Fendley, P.; Saleur, H.; Lesage, F.

    1995-01-01

    The general one-dimensional open-quotes log-sineclose quotes gas is defined by restricting the positive and negative charges of a two-dimensional Coulomb gas to live on a circle. Depending on charge constraints, this problem is equivalent to different boundary field theories. We study the electrically neutral case, which is equivalent to a two-dimensional free boson with an impurity cosine potential. We use two different methods: a perturbative one based on Jack symmetric functions, and a non-perturbative one based on the thermodynamic Bethe ansatz and functional relations. The first method allows us to find an explicit series expression for all coefficients in the virial expansion of the free energy and the experimentally measurable conductance. Some results for correlation functions are also presented. The second method gives an expression for the full free energy, which yields a surprising fluctuation-dissipation relation between the conductance and the free energy

  8. Ficus deltoidea Jack: A Review on Its Phytochemical and Pharmacological Importance

    Directory of Open Access Journals (Sweden)

    Hamidun Bunawan

    2014-01-01

    Full Text Available Ficus deltoidea Jack (Moraceae has had a long history of use in traditional medicine among the Malays to alleviate and heal ailments such as sores, wounds, and rheumatism and as an after-birth tonic and an antidiabetic drug. Modern pharmacological studies demonstrated that this plant has a wide variety of beneficial attributes for human health. Despite its importance, a review of this species has not been published in the scientific literature to date. Here, we review and summarize the historic and current literature concerning the botany, traditional uses, phytochemistry, pharmacological effects, and toxicity of this wonder plant. This summary could be beneficial for future research aiming to exploit the therapeutic potential of this useful, medicinal species.

  9. Multi-gene phylogeny of jacks and pompanos (Carangidae), including placement of monotypic vadigo Campogramma glaycos.

    Science.gov (United States)

    Damerau, M; Freese, M; Hanel, R

    2018-01-01

    In this study, the phylogenetic trees of jacks and pompanos (Carangidae), an ecologically and morphologically diverse, globally distributed fish family, are inferred from a complete, concatenated data set of two mitochondrial (cytochrome c oxidase I, cytochrome b) loci and one nuclear (myosin heavy chain 6) locus. Maximum likelihood and Bayesian inferences are largely congruent and show a clear separation of Carangidae into the four subfamilies: Scomberoidinae, Trachinotinae, Naucratinae and Caranginae. The inclusion of the carangid sister lineages Coryphaenidae (dolphinfishes) and Rachycentridae (cobia), however, render Carangidae paraphyletic. The phylogenetic trees also show with high statistical support that the monotypic vadigo Campogramma glaycos is the sister to all other species within the Naucratinae. © 2017 The Fisheries Society of the British Isles.

  10. Antioxidant and free radical scavenging activities of Gastrodia elata Bl. and Uncaria rhynchophylla (Miq.) Jacks.

    Science.gov (United States)

    Liu, J; Mori, A

    1992-12-01

    Gastrodia elata Bl. (GE) and Uncaria rhynchophylla (Miq.) Jacks (UR) are two traditional Chinese medicinal herbal drugs, used for the treatment of convulsions and epilepsy. Their antioxidant effects in vivo and their free radical scavenging effects in vitro were investigated. Epileptogenic foci in the lateral brain of the rat were induced by the injection of ferric chloride into the lateral cortex. Both extracts significantly inhibited the increase in levels of lipid peroxide in the ipsilateral cortex, at all times observed. In addition, the two extracts also induced an early increase of activity of superoxide dismutase in the mitochondrial fraction of the ipsilateral cortex. In in vitro experiments, the two extracts exhibited significant dose-dependent scavenging effects on free radicals, using electron spin resonance spectroscopy. These results suggest that the proposed antiepileptic effects of GE and UR may be attributable to the antioxidant activity of the active components in these two medicinal herbs.

  11. Evapotranspiration and crop coefficients of corn in monoculture and intercropped with jack bean

    Directory of Open Access Journals (Sweden)

    Mário S. P. de Araújo

    Full Text Available ABSTRACT This study was carried out to determine the evapotranspiration (ETc and crop coefficients (Kc for four stages of “Caatingueiro” corn under the climate condition of Seropédica, RJ, Brazil, using weighing lysimeters. The field trial occurred in 2015, from March 18 to June 25, in two areas cultivated with “Caatingueiro’ corn intercropped with jack bean and in monoculture. The reference evapotranspiration (ETo was estimated by the FAO-56 Penman-Monteith model and the Kc values were determined by the ratio between ETc and ETo. The Kc values obtained for the intercropping and monoculture systems, were respectively: 0.78 (I; 1.01 (II; 1.10 (III and 1.01 (IV, and 0.62 (I; 0.92 (II; 1.27 (III and 0.81 (IV, and they were different from the values presented by FAO.

  12. Tongkat Ali (Eurycoma longifolia Jack): a review on its ethnobotany and pharmacological importance.

    Science.gov (United States)

    Bhat, Rajeev; Karim, A A

    2010-10-01

    Eurycoma longifolia Jack is an herbal medicinal plant of South-East Asian origin, popularly recognized as 'Tongkat Ali.' The plant parts have been traditionally used for its antimalarial, aphrodisiac, anti-diabetic, antimicrobial and anti-pyretic activities, which have also been proved scientifically. The plant parts are rich in various bioactive compounds (like eurycomaoside, eurycolactone, eurycomalactone, eurycomanone, and pasakbumin-B) among which the alkaloids and quassinoids form a major portion. Even though toxicity and safety evaluation studies have been pursued, still a major gap exists in providing scientific base for commercial utilization and clearance of the Tongkat Ali products with regard to consumer's safety. The present review aims at reviewing the research works undertaken till date, on this plant in order to provide sufficient baseline information for future works and for commercial exploitation. Copyright © 2010 Elsevier B.V. All rights reserved.

  13. [Malignant narcissism and sexual homicide--exemplified by the Jack Unterweger case].

    Science.gov (United States)

    Haller, R

    1999-01-01

    With the syndrome of malignant narcissism, which is characterised by narcissistic personality disorder, anti-social behaviour, sadism and a marked tendency to paranoid reactions, Kernberg (1985, 1996) describes an independent form of pathological narcissism. According to Stone (1996) this is found in many mass-murderers and serial killers. On the basis of the example of Jack Unterweger the connection between malignant narcissism and sexual offence is discussed as to psychodynamic development, personality structure and psychopathology. Unterweger, who was convicted to lifelong imprisonment in 1976 for sadistic sexual murder, became a wellknown writer in prison and was released prematurely in 1990 as the Austria case of successful rehabilitation. As stated in the sentence passed against him he killed 11 prostitutes in Europe and the USA within the next 18 months, but never pleaded guilty. Psychiatric examination revealed numerous elements of malignant narcissism and the constellation of his development and life was typical of serial offenders.

  14. Prevalence, severity, and natural history of jack jumper ant venom allergy in Tasmania.

    Science.gov (United States)

    Brown, Simon G A; Franks, Rodney W; Baldo, Brian A; Heddle, Robert J

    2003-01-01

    The jack jumper ant (Myrmecia pilosula) is responsible for greater than 90% of Australian ant venom allergy. However, deaths have only been recorded in the island of Tasmania. We sought to determine the prevalence, clinical features, natural history, and predictors of severity of M pilosula sting allergy in Tasmania. We performed a random telephone survey supported by serum venom-specific IgE analysis, review of emergency department presentations, and follow-up of allergic volunteers. M pilosula, honeybee (Apis mellifera), and yellow jacket wasp (Vespula germanica) sting allergy prevalences were 2.7%, 1.4%, and 0.6% compared with annual sting exposure rates of 12%, 7%, and 2%, respectively. Similarly, emergency department presentations with anaphylaxis to M pilosula were double those for honeybee. M pilosula allergy prevalence increased with age of 35 years or greater (odds ratio [OR], 2.4) and bee sting allergy (OR, 16.9). Patients 35 years of age or older had a greater risk of hypotensive reactions (OR, 2.9). Mueller reaction grades correlated well with adrenaline use. During follow-up, 79 (70%) of 113 jack jumper stings caused anaphylaxis. Prior worst reaction severity predicted the likelihood and severity of follow-up reactions; only 3 subjects had more severe reactions. Venom-specific IgE levels and other clinical features, including comorbidities, were not predictive of severity. Sting allergy prevalence is determined by age and exposure rate. M pilosula sting exposure in Tasmania is excessive compared with that found in mainland Australia, and there is a high systemic reaction risk in allergic people on re-sting. Prior worst reaction severity (Mueller grade) and age predict reaction severity and might be used to guide management.

  15. Jack-knife stretching promotes flexibility of tight hamstrings after 4 weeks: a pilot study.

    Science.gov (United States)

    Sairyo, Koichi; Kawamura, Takeshi; Mase, Yasuyoshi; Hada, Yasushi; Sakai, Toshinori; Hasebe, Kiyotaka; Dezawa, Akira

    2013-08-01

    Tight hamstrings are reported to be one of the causes of low back pain. However, there have been few reports on effective stretching procedures for the tight hamstrings. The so-called jack-knife stretch, an active-static type of stretching, can efficiently increase the flexibility of tight hamstrings. To evaluate hamstring tightness before and after the 4-week stretching protocol in healthy volunteer adults and patients aged under 18 years with low back pain. For understanding the hamstrings tightness, we measured two parameters including (1) finger to floor distance (FFD) and (2) pelvis forward inclination angle (PFIA). Eight healthy adult volunteers who had no lumbar or hip problems participated in this study (mean age: 26.8 years). All lacked flexibility and their FFD were positive before the experiment. Subjects performed 2 sets of the jack-knife stretch every day for 4 weeks. One set consisted of 5 repetitions, each held for 5 s. Before and during the 4-week experiment, the FFD and PFIA of toe-touching tests were measured weekly. For 17 of the sports players aged under 18, only FFD was measured. In adult volunteers, FFD was 14.1 ± 6.1 cm before the experiment and decreased to -8.1 ± 3.7 cm by the end of week 4, indicating a gain in flexibility of 22.2 cm. PFIA was 50.6 ± 8.2 before the experiment and 83.8 ± 5.8 degrees after. Before and after the experiment, the differences were significant (p hamstrings.

  16. The Jack mackerel Trachurus murphyiand the environmental macro-scale variables

    Directory of Open Access Journals (Sweden)

    Marco Espino

    2013-10-01

    Full Text Available This paper analyses information on various macro environmental variables available since 1876 for the Southeast Pacific and more recent data on Jack mackerel Trachurus murphyi (Nichols, 1920 landings and biomass in the Peruvian sea, relating them to probable areas of water masses equivalent to Cold Coastal Waters (CCW and Subtropical Surface Waters (SSW. It is concluded that the index of the Pacific Decadal Oscillation (PDO presents expressions of variability that are consistent with those found for the Southern Oscillation Index (SOI and that the detected changes in biomass of Jack mackerel T. murphyiin the Peruvian sea reflect changes in the availability of the fish stock associated with secular (SOI and decadal (PDO variability patterns. These fluctuations in stock availability impact fisheries in Ecuador, Peru and northern Chile, which show significant variations in their landings and would have given a biased picture of the state of abundance, leading to wrong diagnoses of the real situation of the exploited stocks. These patterns of variability would also affect the appearance of El Niño, making them start in the southern hemisphere autumn or spring depending on whether the current PDO is positive or negative. Periods of high (1876 – 1925 and 1976 – 2012 and low (1926 – 1975 variability are also identified in relation to the Euclidean distance of the variances of the SOI; and in relation to the PDO a distinction is made between warm (1925 – 1944 and 1975 – 1994, cold (1945 – 1974 and tempered or interface periods (1895 – 1924 and 1995 – 2012, the latter being explained by the interaction between periods of high variability.

  17. Procurement strategic analysis of nuclear safety equipment

    International Nuclear Information System (INIS)

    Wu Caixia; Yang Haifeng; Li Xiaoyang; Li Shixin

    2013-01-01

    The nuclear power development plan in China puts forward a challenge on procurement of nuclear safety equipment. Based on the characteristics of the procurement of nuclear safety equipment, requirements are raised for procurement process, including further clarification of equipment technical specification, establishment and improvement of the expert database of the nuclear power industry, adoption of more reasonable evaluation method and establishment of a unified platform for nuclear power plants to procure nuclear safety equipment. This paper makes recommendation of procurement strategy for nuclear power production enterprises from following aspects, making a plan of procurement progress, dividing procurement packages rationally, establishing supplier database through qualification review and implementing classified management, promoting localization process of key equipment continually and further improving the system and mechanism of procurement of nuclear safety equipment. (authors)

  18. Maintenance program guidelines for programmatic equipment

    International Nuclear Information System (INIS)

    1994-11-01

    The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations

  19. RETRIEVAL EQUIPMENT DESCRIPTIONS

    International Nuclear Information System (INIS)

    J. Steinhoff

    1997-01-01

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) retrieval from the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. There are no quality assurance requirements or QA controls in this document. Retrieval under normal conditions is accomplished with the same fleet of equipment as is used for emplacement. Descriptions of equipment used for retrieval under normal conditions is found in Emplacement Equipment Descriptions, DI: BCAF00000-01717-5705-00002 (a document in progress). Equipment used for retrieval under abnormal conditions is addressed in this document and consists of the following: (1) Inclined Plane Hauler; (2) Bottom Lift Transporter; (3) Load Haul Dump (LHD) Loader; (4) Heavy Duty Forklift for Emplacement Drifts; (5) Covered Shuttle Car; (6) Multipurpose Vehicle; and (7) Scaler

  20. Development and design of control rod drive mechanisms for pressurized water reactors

    International Nuclear Information System (INIS)

    Leme, Francisco Louzano

    2003-01-01

    The Control Rod Drive Mechanisms (CRDM) for a Pressurized Water Reactor (PWR) are equipment, integrated to the reactor pressure vessel, incorporating mechanical and electrical components designed to move and position the control rods to guarantee the control of power and shutdown of the nuclear reactor, during normal operation, either in emergency or accidental situations. The type of CRDM used in PWR reactors, whose detailed individual description will be presented in this monograph are the Roller-Nut and Magnetic-Jack. The environment, where the CRDM performs its above presented operational functions, includes direct contact with the fluid used as coolant peculiar to the interior of the reactor, and its associated chemical characteristics, the radiation field next to the reactor core, and also the temperature and pressure in the reactor pressure vessel. So the importance of the CRDM design requirements related to its safety functions are emphasized. Finally, some aspects related to the mechanical and structural design of CRDM of a case study, considering the CRDM for a PWR from the experimental nuclear plant to be applied by CTMSP (Centro Tecnologico da Marinha em Sao Paulo), are pointed out. The design and development of these equipment (author)

  1. Medical equipment management

    CERN Document Server

    Willson, Keith; Tabakov, Slavik

    2013-01-01

    Know What to Expect When Managing Medical Equipment and Healthcare Technology in Your Organization As medical technology in clinical care becomes more complex, clinical professionals and support staff must know how to keep patients safe and equipment working in the clinical environment. Accessible to all healthcare professionals and managers, Medical Equipment Management presents an integrated approach to managing medical equipment in healthcare organizations. The book explains the underlying principles and requirements and raises awareness of what needs to be done and what questions to ask. I

  2. Data communication equipment

    International Nuclear Information System (INIS)

    Kim, Hak Seon; Lee, Sang Mok

    1998-02-01

    The contents of this book are introduction of data communication on definition, purpose and history, information terminal about data communication system and data transmission system, data transmit equipment of summary, transmission cable, data port, concentrator and front-end processor, audio communication equipment like phones, radio communication equipment of summary on foundation of electromagnetic waves, AM transmitter, AM receiver, FM receiver and FM transmitter, a satellite and mobile communication equipment such as earth station, TT and C and Cellular phone, video telephone and new media apparatus.

  3. Survey of foliar monoterpenes across the range of jack pine reveal three widespread chemotypes: implications to host expansion of invasive mountain pine beetle

    Directory of Open Access Journals (Sweden)

    Spencer eTaft

    2015-05-01

    Full Text Available The secondary compounds of pines (Pinus can strongly affect the physiology, ecology and behaviors of the bark beetles (Coleoptera: Curculionidae, Scolytinae that feed on sub-cortical tissues of hosts. Jack pine (Pinus banksiana has a wide natural distribution range in North America (Canada and USA and thus variations in its secondary compounds, particularly monoterpenes, could affect the host expansion of invasive mountain pine beetle (Dendroctonus ponderosae, which has recently expanded its range into the novel jack pine boreal forest. We investigated monoterpene composition of 601 jack pine trees from natural and provenance forest stands representing 63 populations from Alberta to the Atlantic coast. Throughout its range, jack pine exhibited three chemotypes characterized by high proportions of α-pinene, β-pinene, or limonene. The frequency with which the α-pinene and β-pinene chemotypes occurred at individual sites was correlated to climatic variables, such as continentality and mean annual precipitation, as were the individual α-pinene and β-pinene concentrations. However, other monoterpenes were generally not correlated to climatic variables or geographic distribution. Finally, while the enantiomeric ratios of β-pinene and limonene remained constant across jack pine’s distribution, (‒:(+-α-pinene exhibited two separate trends, thereby delineating two α-pinene phenotypes, both of which occurred across jack pine’s range. These significant variations in jack pine monoterpene composition may have cascading effects on the continued eastward spread and success of D. ponderosae in the Canadian boreal forest.

  4. Mechanics

    CERN Document Server

    Hartog, J P Den

    1961-01-01

    First published over 40 years ago, this work has achieved the status of a classic among introductory texts on mechanics. Den Hartog is known for his lively, discursive and often witty presentations of all the fundamental material of both statics and dynamics (and considerable more advanced material) in new, original ways that provide students with insights into mechanical relationships that other books do not always succeed in conveying. On the other hand, the work is so replete with engineering applications and actual design problems that it is as valuable as a reference to the practicing e

  5. Cooling of electronic equipment

    DEFF Research Database (Denmark)

    A. Kristensen, Anders Schmidt

    2003-01-01

    Cooling of electronic equipment is studied. The design size of electronic equipment decrease causing the thermal density to increase. This affect the cooling which can cause for example failures of critical components due to overheating or thermal induced stresses. Initially a pin fin heat sink...

  6. Capital Equipment Replacement Decisions

    OpenAIRE

    Batterham, Robert L.; Fraser, K.I.

    1995-01-01

    This paper reviews the literature on the optimal replacement of capital equipment, especially farm machinery. It also considers the influence of taxation and capital rationing on replacement decisions. It concludes that special taxation provisions such as accelerated depreciation and investment allowances are unlikely to greatly influence farmers' capital equipment replacement decisions in Australia.

  7. Division of Scientific Equipment - Overview

    International Nuclear Information System (INIS)

    Halik, J.

    2002-01-01

    Full text: The Scientific Equipment Division consists of the Design Group and the Mechanical Workshop. The activity of the Division includes the following: * designs of devices and equipment for experiments in physics; their mechanical construction and assembly. In particular, these are vacuum chambers and installations for HV and UHV;* maintenance and upgrading of the existing installations and equipment in our Institute; * participation of our engineers and technicians in design works, equipment assembly and maintenance for experiments in foreign laboratories. The Design Group is equipped with PC-computers and AutoCAD graphic software (release 2000 and Mechanical Desktop 4.0) and an A0 plotter, which allow us to make drawings and 2- and 3-dimensional mechanical documentation to the world standards. The Mechanical Workshop offers a wide range of machining and treatment methods with satisfactory tolerances and surface quality. They include: * turning - cylindrical elements of a length up to 2000 mm and a diameter up to 400 mm, and also disc type elements of a diameter up to 600 mm and a length not exceeding 300 mm, * milling - elements of length up to 1000 mm and gear wheels of diameter up to 300 mm, * grinding - flat surfaces of dimensions up to 300 mm x 1000 mm and cylindrical elements of a diameter up to 200 mm and a length up to 800 mm, * drilling - holes of a diameter up to 50 mm, * welding - electrical and gas welding, including TIG vacuum-tight welding, * soft and hard soldering, * mechanical works including precision engineering, * plastics treatment - machining and polishing using diamond milling, modelling, lamination of various shapes and materials, including plexiglas, scintillators and light-guides, * painting - paint spraying with possibility of using furnace-fired drier of internal dimensions of 800 mm x 800 mm x 800 mm. Our workshop is equipped with the CNC milling machine which can be used for machining of work pieces up to 500 kg. The machine

  8. 46 CFR 133.45 - Tests and inspections of lifesaving equipment and arrangements.

    Science.gov (United States)

    2010-10-01

    ... of flotation equipment such as lifebuoys, lifejackets, immersion suits, work vests, lifefloats... mechanisms; (3) The proper condition of flotation equipment such as lifebuoys, lifejackets, immersion suits, work vests, lifefloats, buoyant apparatus, and associated equipment; (4) That each inflatable liferaft...

  9. Equipment qualification research program: program plan

    International Nuclear Information System (INIS)

    Dong, R.G.; Smith, P.D.

    1982-01-01

    The Lawrence Livermore National Laboratory (LLNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has developed this program plan for research in equipment qualification (EQA). In this report the research program which will be executed in accordance with this plan will be referred to as the Equipment Qualification Research Program (EQRP). Covered are electrical and mechanical equipment under the conditions described in the OBJECTIVE section of this report. The EQRP has two phases; Phase I is primarily to produce early results and to develop information for Phase II. Phase I will last 18 months and consists of six projects. The first project is program management. The second project is responsible for in-depth evaluation and review of EQ issues and EQ processes. The third project is responsible for detailed planning to initiate Phase II. The remaining three projects address specific equipment; i.e., valves, electrical equipment, and a pump

  10. Jack'd, a Mobile Social Networking Application: A Site of Exclusion Within a Site of Inclusion.

    Science.gov (United States)

    Bartone, Michael D

    2018-01-01

    User-generated smartphone applications have created a new level of virtual connectivity for gay males, one in which users can create profiles and meet other users as nearby or as far away as possible. For those within close proximity, the other users can be considered their "virtual neighbors." Although the applications are theoretically designed to be places of inclusion and not exclusion, where any gay male with economic means can download an application, many profiles have been created that exclude other users. Through an examination of profiles on one such application, Jack'd, exclusion is found in the way users celebrate and reinforce ideas of traditional masculinity and denigrate and reinforce stereotypic ideas of femininity embodied by some gay men. Jack'd, and other user-generated smartphone applications, can be read as virtual neighborhoods where one is excluded based on their gender performance.

  11. Effect of Pasak Bumi (Eurycoma longifolia Jack) Root In Precopulation Stage to the Fertility of Female Mouse (Mus musculus L.)

    OpenAIRE

    Marlinza, Rosa

    2012-01-01

    Pasak Bumi (Eurycoma longifolia Jack) have potency to be used to increase bodyendurance, to cure malaria drug, and to act as afrodisiak. However, the effect of pasak bumi onwomen fertility, especially at pre-copulation stage was not widely known. This research seeks toreveal the effect pasak bumi extract treated at pre-copulation phase on fertility. This experimentemploy mice (Mus Musculus L.) and was undertaken at Biology and Cemistry laboratories PMIPA, andVeterinary laboratory of Jambi Uni...

  12. Comparison of lodgepole and jack pine resin chemistry: implications for range expansion by the mountain pine beetle, Dendroctonus ponderosae (Coleoptera: Curculionidae

    Directory of Open Access Journals (Sweden)

    Erin L. Clark

    2014-02-01

    Full Text Available The mountain pine beetle, Dendroctonus ponderosae, is a significant pest of lodgepole pine in British Columbia (BC, where it has recently reached an unprecedented outbreak level. Although it is native to western North America, the beetle can now be viewed as a native invasive because for the first time in recorded history it has begun to reproduce in native jack pine stands within the North American boreal forest. The ability of jack pine trees to defend themselves against mass attack and their suitability for brood success will play a major role in the success of this insect in a putatively new geographic range and host. Lodgepole and jack pine were sampled along a transect extending from the beetle’s historic range (central BC to the newly invaded area east of the Rocky Mountains in north-central Alberta (AB in Canada for constitutive phloem resin terpene levels. In addition, two populations of lodgepole pine (BC and one population of jack pine (AB were sampled for levels of induced phloem terpenes. Phloem resin terpenes were identified and quantified using gas chromatography. Significant differences were found in constitutive levels of terpenes between the two species of pine. Constitutive α-pinene levels – a precursor in the biosynthesis of components of the aggregation and antiaggregation pheromones of mountain pine beetle – were significantly higher in jack pine. However, lower constitutive levels of compounds known to be toxic to bark beetles, e.g., 3-carene, in jack pine suggests that this species could be poorly defended. Differences in wounding-induced responses for phloem accumulation of five major terpenes were found between the two populations of lodgepole pine and between lodgepole and jack pine. The mountain pine beetle will face a different constitutive and induced phloem resin terpene environment when locating and colonizing jack pine in its new geographic range, and this may play a significant role in the ability of the

  13. Comparison of lodgepole and jack pine resin chemistry: implications for range expansion by the mountain pine beetle, Dendroctonus ponderosae (Coleoptera: Curculionidae).

    Science.gov (United States)

    Clark, Erin L; Pitt, Caitlin; Carroll, Allan L; Lindgren, B Staffan; Huber, Dezene P W

    2014-01-01

    The mountain pine beetle, Dendroctonus ponderosae, is a significant pest of lodgepole pine in British Columbia (BC), where it has recently reached an unprecedented outbreak level. Although it is native to western North America, the beetle can now be viewed as a native invasive because for the first time in recorded history it has begun to reproduce in native jack pine stands within the North American boreal forest. The ability of jack pine trees to defend themselves against mass attack and their suitability for brood success will play a major role in the success of this insect in a putatively new geographic range and host. Lodgepole and jack pine were sampled along a transect extending from the beetle's historic range (central BC) to the newly invaded area east of the Rocky Mountains in north-central Alberta (AB) in Canada for constitutive phloem resin terpene levels. In addition, two populations of lodgepole pine (BC) and one population of jack pine (AB) were sampled for levels of induced phloem terpenes. Phloem resin terpenes were identified and quantified using gas chromatography. Significant differences were found in constitutive levels of terpenes between the two species of pine. Constitutive α-pinene levels - a precursor in the biosynthesis of components of the aggregation and antiaggregation pheromones of mountain pine beetle - were significantly higher in jack pine. However, lower constitutive levels of compounds known to be toxic to bark beetles, e.g., 3-carene, in jack pine suggests that this species could be poorly defended. Differences in wounding-induced responses for phloem accumulation of five major terpenes were found between the two populations of lodgepole pine and between lodgepole and jack pine. The mountain pine beetle will face a different constitutive and induced phloem resin terpene environment when locating and colonizing jack pine in its new geographic range, and this may play a significant role in the ability of the insect to persist in

  14. HVAC systems and equipment

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, S.T. (Linford Air and Refrigeration Company, Oakland, CA (US))

    1990-02-01

    The author discusses the section of the ASHRAE Standard 90.1-1989 which addresses HVAC systems and equipment. New features of HVAC systems mandatory general requirements are described. New prescriptive requirements are detailed.

  15. Personal Protective Equipment

    National Research Council Canada - National Science Library

    1998-01-01

    ... of personal protective equipment A safety program for new employees is a necessary part of any orientation program An on-going safety program should be used to motivate employees to continue to use...

  16. Electronic equipment packaging technology

    CERN Document Server

    Ginsberg, Gerald L

    1992-01-01

    The last twenty years have seen major advances in the electronics industry. Perhaps the most significant aspect of these advances has been the significant role that electronic equipment plays in almost all product markets. Even though electronic equipment is used in a broad base of applications, many future applications have yet to be conceived. This versatility of electron­ ics has been brought about primarily by the significant advances that have been made in integrated circuit technology. The electronic product user is rarely aware of the integrated circuits within the equipment. However, the user is often very aware of the size, weight, mod­ ularity, maintainability, aesthetics, and human interface features of the product. In fact, these are aspects of the products that often are instrumental in deter­ mining its success or failure in the marketplace. Optimizing these and other product features is the primary role of Electronic Equipment Packaging Technology. As the electronics industry continues to pr...

  17. CV equipment responsibilities

    CERN Document Server

    Pirollet, B

    2008-01-01

    This document describes the limits of the responsibilities of the TS/CV for fire fighting equipment at the LHC. The various interfaces, providers and users of the water supply systems and clean water raising systems are described.

  18. Equipment for hydraulic testing

    International Nuclear Information System (INIS)

    Jacobsson, L.; Norlander, H.

    1981-07-01

    Hydraulic testing in boreholes is one major task of the hydrogeological program in the Stripa Project. A new testing equipment for this purpose was constructed. It consists of a downhole part and a surface part. The downhole part consists of two packers enclosing two test-sections when inflated; one between the packers and one between the bottom packer and the bottom of the borehole. A probe for downhole electronics is also included in the downhole equipment together with electrical cable and nylon tubing. In order to perform shut-in and pulse tests with high accuracy a surface controlled downhole valve was constructed. The surface equipment consists of the data acquisition system, transducer amplifier and surface gauges. In the report detailed descriptions of each component in the whole testing equipment are given. (Auth.)

  19. Experience with rotating equipment in FBTR

    International Nuclear Information System (INIS)

    Babu, A.; Subramanian, K.G.; Selvam, B.

    2006-01-01

    Fast breeder test reactor (FBTR) is a 40MWth sodium cooled PuC-UC fuelled fast breeder reactor located at Kalpakkam, Tamilnadu. FBTR has a variety of mechanical and electrical equipment comprising of single stage and multi stage water pumps, sodium pumps, compressors, Chiller units, Diesel Generator sets, vacuum pumps, ventilation fans, Turbo generator etc. The degree and extent of maintenance on these equipment are decided based on nuclear safety, station technical specification requirements, design criteria and operating philosophy. The variety and complexity of the equipment in FBTR demands various maintenance strategies (preventive, predictive, proactive etc.) for their upkeep. This paper discusses the performance of all mechanical and electrical equipment in FBTR, measures taken for their upkeep, major modifications done to prevent recurring failures, condition monitoring programme implemented, Maintenance Management and Information System developed for data acquisition and dissemination, etc. (author)

  20. Analysis of Floating Buoy of a Wave Power Generating Jack-Up Platform Haiyuan 1

    Directory of Open Access Journals (Sweden)

    Date Li

    2013-01-01

    Full Text Available The paper focuses on the performance of floating buoys of a wave power generating jack-up platform called Haiyuan 1, in order to work out the optimum designed draft and hydraulic pressure. The performance of the buoy, especially its delivered power, is an important issue in designing oscillating buoy wave energy converter. In this case, major factors affect the performance including incident wave, designed draft, and hydraulic pressure on the buoy. To find out the relationship among design draft, hydraulic pressure, and delivered power, the key point is to precisely estimate wave induced motion of the buoy. Three-dimensional theory and time domain method based on potential theory were adopted in the paper. Unlike ship and other floating structures, motion of wave energy converter (WEC buoy in wave will be weakened because of energy take-off, which will cause significant draft changing with time. Thus, draft changing should be taken into consideration as well. In addition, green water problem occurs more frequently than that in ship and other floating structures and also might the reduce delivered power. Therefore, green water problem will also be taken into account when choosing the optimum designed draft and hydraulic pressure. The calculation indicates that the optimum designed draft is 0.935 m, while the optimum designed hydraulic pressure is 30 kN.

  1. Non-reef environments impact the diversification of extant jacks, remoras and allies (Carangoidei, Percomorpha).

    Science.gov (United States)

    Frédérich, Bruno; Marramà, Giuseppe; Carnevale, Giorgio; Santini, Francesco

    2016-11-16

    Various factors may impact the processes of diversification of a clade. In the marine realm, it has been shown that coral reef environments have promoted diversification in various fish groups. With the exception of requiem sharks, all the groups showing a higher level of diversity in reefs than in non-reef habitats have diets based predominantly on plankton, algae or benthic invertebrates. Here we explore the pattern of diversification of carangoid fishes, a clade that includes numerous piscivorous species (e.g. trevallies, jacks and dolphinfishes), using time-calibrated phylogenies as well as ecological and morphological data from both extant and fossil species. The study of carangoid morphospace suggests that reef environments played a role in their early radiation during the Eocene. However, contrary to the hypothesis of a reef-association-promoting effect, we show that habitat shifts to non-reef environments have increased the rates of morphological diversification (i.e. size and body shape) in extant carangoids. Piscivory did not have a major impact on the tempo of diversification of this group. Through the ecological radiation of carangoid fishes, we demonstrate that non-reef environments may sustain and promote processes of diversification of different marine fish groups, at least those including a large proportion of piscivorous species. © 2016 The Author(s).

  2. Safe jack-up method permits repairs of tank bottoms and foundations

    International Nuclear Information System (INIS)

    de Wit, J.

    1991-01-01

    The oil and chemical industries use many thousands of steel tanks to store crude oil, oil products, and chemical liquids. The majority of these tanks are 30-40 years old. Tank bottoms are likely to begin leaking in the coming years, as these tanks get older. The European technique of jacking up a tank and repairing its foundation allows the thorough inspection of the underside of the tank bottom and the removal of saturated foundation material. And the possibility of soil and groundwater pollution is reduced to a minimum. With good, regular maintenance, the lifetime of a storage tank is very long. But experience has shown that special attention should be paid to the tank's bottom. Tank bottoms are only 5 or 6 mm thick, and in the last 10 years, an increasing number of leaks in tank bottoms have been reported. Tank foundations are affected by these leaks. This article describes the resulting procedure, which is used successfully in many European countries, but is not yet common in the U.S

  3. Anti-diabetic Activity of Tabat Barito Leafs (Ficus deltoidea, Jack Extract in Rats

    Directory of Open Access Journals (Sweden)

    Heru Agus Cahyanto

    2013-06-01

    Full Text Available Tabat barito (Ficus deltoidea, Jack leaf is believed could be used to treat diabetes. But more scientific data are needed. The aim of this study is to investigate  antidiabetic activity of  Tabat Barito extract by glucose tolerance method. The treatment was given in three doses (50, 100, and 200 mg/kg BW and two controls using aquoeus and glibenklamid.  Tabat barito extract was obtained by maceration and made into dry extract with addition of starch. The result showed that chemical compound of the ethanol extract were fenolic and saponin. The extract showed effects in lowering blood sugar levels with glucose tolerance methods at 30 to 60 minutes. Blood glucose levels of mice treated with the extract extract ranged between 132.60 to 258.00 mg/dL , glibenklamide ranged from 130.20 to 144.60 mg/dL, and aqua ranged between 227.60 to 260.20 mg/dL. The percentage decrease in blood sugar levels compared to controls is 32.54%.

  4. Development of observational learning during school formation in jack mackerel Trachurus japonicus juveniles.

    Science.gov (United States)

    Takahashi, Kohji; Masuda, Reiji; Yamashita, Yoh

    2014-03-01

    We assessed whether the development of observational learning in jack mackerel Trachurus japonicus juveniles corresponds with that of their schooling behaviour. Schooling behaviour was quantitatively analyzed by nearest neighbour distance and separation angle in two size classes of fish, 20-mm and 40-mm in body length. Observer and non-observer fish with matching sizes were conditioned to pellets by temporarily stopping aeration. Observer fish were provided with five observation trials of other individuals feeding near an air stone when aeration was stopped. After the observation trial, fish were conditioned to pellets with the stop of aeration, and then the learning process was evaluated by the increase in the association with the feeding area when aeration was stopped. In 20-mm fish, which were at an immature stage of schooling behaviour, there was no difference in the learning process between observer and non-observer fish. In contrast, 40-mm fish were confirmed to have a well-developed schooling behaviour, and the observer learnt the feeding area more efficiently than the non-observer. This study provides evidence that observational learning develops along with the development of the social interaction. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. What to copy: the key factor of observational learning in striped jack (Pseudocaranx dentex) juveniles.

    Science.gov (United States)

    Takahashi, K; Masuda, R; Yamashita, Y

    2014-03-01

    Animals in social environments can enhance their learning efficiency by observing the behaviour of others. Our previous study showed that learning efficiency of schooling fish increased through the observation of the behaviour of trained demonstrator conspecifics. The present study aimed to verify the key factor of observational learning by investigating what information is important for social transmission of feeding information. A striped jack (Pseudocaranx dentex) observer was provided with one of the five observation treatments: (a) pellets observation, where pellets were dropped near the aeration in an adjacent tank; (b) responding conspecific observation, where a trained conspecific demonstrator responded to the aeration without food in the adjacent tank; (c) foraging conspecific observation, where a conspecific demonstrator foraged near the aeration in the adjacent tank; (d) nearby pellets observation, where pellets were dropped in a transparent column near the aeration in the observer tank; and (e) foraging heterospecific observation, where a filefish (Stephanolepis cirrhifer) demonstrator foraged near the aeration in the adjacent tank. The response to the aeration in these observers was compared with that of controls who did not observe any behaviour. Only individuals who observed foraging conspecifics showed a response to the aeration after observing. These results suggest that observer fish acquire feeding information not through recognition of prey items or through imitation of the demonstrator, but through the vicarious reinforcement of a conspecific for foraging.

  6. Uncaria rhynchophylla (miq) Jack plays a role in neuronal protection in kainic acid-treated rats.

    Science.gov (United States)

    Tang, Nou-Ying; Liu, Chung-Hsiang; Su, Shan-Yu; Jan, Ya-Min; Hsieh, Ching-Tou; Cheng, Chin-Yi; Shyu, Woei-Cherng; Hsieh, Ching-Liang

    2010-01-01

    Uncaria rhynchophylla (Miq) Jack (UR) is one of many Chinese herbs. Our previous studies have shown that UR has both anticonvulsive and free radical-scavenging activities in kainic acid (KA)-treated rats. The aim of the present study was to use the effect of UR on activated microglia, nitric oxide synthase, and apoptotic cells to investigate its function in neuroproction in KA-treated rats. UR of 1.0 or 0.5 g/kg was orally administered for 3 days (first day, second day, and 30 min prior to KA administration on the third day), or 10 mg/kg (intraperitoneal injection, i.p.) N-nitro-L-arginine methyl ester (L-NAME) 30 min prior to KA (2 microg/2 microl) was injected into the right hippocampus region of Sprague-Dawly rats. ED1 (mouse anti rat CD68), neuronal nitric oxide synthase (nNOS), inducible nitric oxide synthase (iNOS) immunoreactive cells and apoptotic cells were observed in the hippocampus region. The results indicated that 1.0 g/kg, 0.5 g/kg of UR and 10 mg/kg of L-NAME reduced the counts of ED1, nNOS, iNOS immunoreactive cells and apoptotic cells in KA-treated rats. This study demonstrates that UR can reduce microglia activation, nNOS, iNOS and apoptosis, suggesting that UR plays a neuro-protective role against neuronal damage in KA-treated rats.

  7. Within crown variation in the relationship between foliage biomass and sapwood area in jack pine.

    Science.gov (United States)

    Schneider, Robert; Berninger, Frank; Ung, Chhun-Huor; Mäkelä, Annikki; Swift, D Edwin; Zhang, S Y

    2011-01-01

    The relationship between sapwood area and foliage biomass is the basis for a lot of research on eco-phyisology. In this paper, foliage biomass change between two consecutive whorls is studied, using different variations in the pipe model theory. Linear and non-linear mixed-effect models relating foliage differences to sapwood area increments were tested to take into account whorl location, with the best fit statistics supporting the non-linear formulation. The estimated value of the exponent is 0.5130, which is significantly different from 1, the expected value given by the pipe model theory. When applied to crown stem sapwood taper, the model indicates that foliage biomass distribution influences the foliage biomass to sapwood area at crown base ratio. This result is interpreted as being the consequence of differences in the turnover rates of sapwood and foliage. More importantly, the model explains previously reported trends in jack pine sapwood area at crown base to tree foliage biomass ratio.

  8. Immune-mediated thrombocytopenia associated with angiostrongylus vasorum infection in a jack russell terrier

    Directory of Open Access Journals (Sweden)

    JO'Neill Emma

    2010-07-01

    Full Text Available Abstract A twenty-month-old Jack Russell terrier was presented with a four-day history of thrombocytopenia, echymotic inguinal haemorrhages, coughing and reduced exercise tolerance. Clinical examination revealed several petechial haemorrhages on the gingivae and small echymotic haemorrhages in the inguinal region, along with mild bilateral epistaxis. Haematology confirmed a platelet count of 1.0 × 10/L. Thoracic radiographs revealed a wide-spread mixed alveolar-interstitial lung pattern, apparent throughout the entire lungfield, but particularly marked within the left lung lobes. A presumptive diagnosis of immune-mediated thrombocytopenia was made and the dog was treated with vincristine and immunosuppressive doses of prednisolone. Initially anaemia developed following gastrointestinal haemorrhage; however, after symptomatic treatment the dog showed a marked clinical improvement. Evaluation for an underlying cause of the disease revealed Angiostrongylus vasorum L1 larvae on faecal analysis and treatment with fenbendazole was commenced. The dog made a full clinical recovery with all treatment was withdrawn within five weeks of diagnosis. This is the second report of immune-mediated thrombocytopenia associated with Angiostrongylus vasorum infection and it is the first to be successfully managed. The report highlights that Angiostrongylus vasorum should be considered in young dogs presented with thrombocytopenia.

  9. Preliminary report and design of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan

    International Nuclear Information System (INIS)

    McLean, L.; Ireland, J.; Hohn, S.; Herman, L.; Hanna, A.

    1999-01-01

    A study is being conducted to evaluate the feasibility of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan. The sites have some level of diesel contamination from spills associated with generators belonging to SaskTel. The first phase of the study was conducted under controlled conditions in a greenhouse. Seedlings of Jack Pine were planted in sand with a range of diesel concentrations. A control planting of seedlings with no diesel was also conducted. The study also included control pots of sand with diesel and no seedlings for comparison of diesel degradation. The results from this first phase will help determine the feasibility of performing more extensive testing of phytoremediation on site in northern Saskatchewan. Results will be conclusive in August 2000. So far, the results show that Jack Pines can survive in soil highly contaminated with hydrocarbons. The second phase will include field trials. Diesel concentrations at the sites range from 0 ppm to 30,000 ppm. 4 refs., 2 tabs., 5 figs

  10. Preliminary report and design of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan

    Energy Technology Data Exchange (ETDEWEB)

    McLean, L; Ireland, J; Hohn, S; Herman, L [ERIN Consulting Ltd., Regina, SK (Canada); Hanna, A [SaskTel, Regina, SK (Canada)

    1999-01-01

    A study is being conducted to evaluate the feasibility of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan. The sites have some level of diesel contamination from spills associated with generators belonging to SaskTel. The first phase of the study was conducted under controlled conditions in a greenhouse. Seedlings of Jack Pine were planted in sand with a range of diesel concentrations. A control planting of seedlings with no diesel was also conducted. The study also included control pots of sand with diesel and no seedlings for comparison of diesel degradation. The results from this first phase will help determine the feasibility of performing more extensive testing of phytoremediation on site in northern Saskatchewan. Results will be conclusive in August 2000. So far, the results show that Jack Pines can survive in soil highly contaminated with hydrocarbons. The second phase will include field trials. Diesel concentrations at the sites range from 0 ppm to 30,000 ppm. 4 refs., 2 tabs., 5 figs.

  11. Fire Regime in Marginal Jack Pine Populations at Their Southern Limit of Distribution, Riding Mountain National Park, Central Canada

    Directory of Open Access Journals (Sweden)

    Jacques C. Tardif

    2016-09-01

    Full Text Available In central Canada, long fire history reconstructions are rare. In a context where both anthropogenic and climate influences on fire regime have changed, Parks Canada has a mandate to maintain ecological integrity. Here we present a fire history derived from fire-scarred jack pine (Pinus banksiana Lamb. trees growing at their southern distribution limit in Riding Mountain National Park (RMNP. In Lake Katherine Fire Management Unit (LKFMU, a subregion within the park, fire history was reconstructed from archival records, tree-ring records, and charcoal in lake sediment. From about 1450 to 1850 common era (CE the fire return intervals varied from 37 to 125 years, according to models. During the period 1864–1930 the study area burned frequently (Weibull Mean Fire Intervals between 2.66 and 5.62 years; this period coincided with the end of First Nations occupation and the start of European settlement. Major recruitment pulses were associated with the stand-replacing 1864 and 1894 fires. This period nevertheless corresponded to a reduction in charcoal accumulation. The current fire-free period in LKFMU (1930–today coincides with RMNP establishment, exclusion of First Nations land use and increased fire suppression. Charcoal accumulation further decreased during this period. In the absence of fire, jack pine exclusion in LKFMU is foreseeable and the use of prescribed burning is advocated to conserve this protected jack pine ecosystem, at the southern margins of its range, and in the face of potential climate change.

  12. Population structure of a lodgepole pine (Pinus contorta) and jack pine (P. banksiana) complex as revealed by random amplified polymorphic DNA.

    Science.gov (United States)

    Ye, Terrance Z; Yang, Rong-Cai; Yeh, Francis C

    2002-06-01

    We studied the population structure of a lodgepole (Pinus contorta Dougl.) and jack pine (Pinus banksiana Lamb.) complex in west central Alberta and neighboring areas by assessing random amplified polymorphic DNA (RAPD) variability in 23 lodgepole pine, 9 jack pine, and 8 putative hybrid populations. Of 200 random primers screened, 10 that amplified 39 sharp and reproducible RAPDs were chosen for the study. None of the 39 RAPDs were unique to the parental species. RAPD diversity ranged from 0.085 to 0.190 among populations and averaged 0.143 for lodgepole pine, 0.156 for jack pine, 0.152 for hybrids, and 0.148 for all 40 populations. The estimated population differentiation based on G(ST) was 0.168 for hybrids, 0.162 for lodgepole pine, 0.155 for jack pine, and 0.247 across all 40 populations. Cluster analysis of genetic distances generally separated jack pine from lodgepole pine and hybrids, but no division could be identified that further separated lodgepole pine from hybrids. The observed weak to mild trend of "introgression by distance" in the complex and neighbouring areas was consistent with the view that introgressive hybridization between lodgepole and jack pines within and outside the hybrid zone may have been through secondary contact and primary intergradation, respectively.

  13. Equipment for x- and gamma ray radiography

    International Nuclear Information System (INIS)

    Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail

    2004-01-01

    The following topics related to the equipment for x - and gamma ray radiography are discussed in this chapter. The topics are x-ray source for Industrial Radiography: properties of x-ray, generation of x-ray, mechanism of x-ray production, x-ray equipment, power supply, distribution of x-ray intensity along the tube: gamma ray source for Industrial Radiography: properties of gamma rays, gamma ray sources, gamma ray projectors on cameras, source changing. Care of Radiographic Equipments: Merits and Demerits of x and Gamma Rays

  14. The french safety approach regarding equipment qualification

    International Nuclear Information System (INIS)

    Jalouneix, J.; Deletre, G.; Henry, J.Y.; Rousseau, L.

    1989-10-01

    The qualification of the equipment, used in France on nuclear reactors and reactor components, is discussed. The approach on safety involves the qualification of mechanical and electrical components, under operating and under seismic conditions. The principles of the qualification program and the list of the equipment concerned, are given. The conditions in which qualification tests are performed and the methods applied, are summarized. The actions for preserving the qualification procedures, are considered

  15. Mechanics

    CERN Document Server

    Chester, W

    1979-01-01

    When I began to write this book, I originally had in mind the needs of university students in their first year. May aim was to keep the mathematics simple. No advanced techniques are used and there are no complicated applications. The emphasis is on an understanding of the basic ideas and problems which require expertise but do not contribute to this understanding are not discussed. How­ ever, the presentation is more sophisticated than might be considered appropri­ ate for someone with no previous knowledge of the subject so that, although it is developed from the beginning, some previous acquaintance with the elements of the subject would be an advantage. In addition, some familiarity with element­ ary calculus is assumed but not with the elementary theory of differential equations, although knowledge of the latter would again be an advantage. It is my opinion that mechanics is best introduced through the motion of a particle, with rigid body problems left until the subject is more fully developed. Howev...

  16. Increased air temperature during simulated autumn conditions does not increase photosynthetic carbon gain but affects the dissipation of excess energy in seedlings of the evergreen conifer Jack pine.

    Science.gov (United States)

    Busch, Florian; Hüner, Norman P A; Ensminger, Ingo

    2007-03-01

    Temperature and daylength act as environmental signals that determine the length of the growing season in boreal evergreen conifers. Climate change might affect the seasonal development of these trees, as they will experience naturally decreasing daylength during autumn, while at the same time warmer air temperature will maintain photosynthesis and respiration. We characterized the down-regulation of photosynthetic gas exchange and the mechanisms involved in the dissipation of energy in Jack pine (Pinus banksiana) in controlled environments during a simulated summer-autumn transition under natural conditions and conditions with altered air temperature and photoperiod. Using a factorial design, we dissected the effects of daylength and temperature. Control plants were grown at either warm summer conditions with 16-h photoperiod and 22 degrees C or conditions representing a cool autumn with 8 h/7 degrees C. To assess the impact of photoperiod and temperature on photosynthesis and energy dissipation, plants were also grown under either cold summer (16-h photoperiod/7 degrees C) or warm autumn conditions (8-h photoperiod/22 degrees C). Photosynthetic gas exchange was affected by both daylength and temperature. Assimilation and respiration rates under warm autumn conditions were only about one-half of the summer values but were similar to values obtained for cold summer and natural autumn treatments. In contrast, photosynthetic efficiency was largely determined by temperature but not by daylength. Plants of different treatments followed different strategies for dissipating excess energy. Whereas in the warm summer treatment safe dissipation of excess energy was facilitated via zeaxanthin, in all other treatments dissipation of excess energy was facilitated predominantly via increased aggregation of the light-harvesting complex of photosystem II. These differences were accompanied by a lower deepoxidation state and larger amounts of beta-carotene in the warm autumn

  17. Equipment abnormality monitoring device

    International Nuclear Information System (INIS)

    Ando, Yasumasa

    1991-01-01

    When an operator hears sounds in a plantsite, the operator compares normal sounds of equipment which he previously heard and remembered with sounds he actually hears, to judge if they are normal or abnormal. According to the method, there is a worry that abnormal conditions can not be appropriately judged in a case where the number of objective equipments is increased and in a case that the sounds are changed gradually slightly. Then, the device of the present invention comprises a plurality of monitors for monitoring the operation sound of equipments, a recording/reproducing device for recording and reproducing the signals, a selection device for selecting the reproducing signals among the recorded signals, an acoustic device for converting the signals to sounds, a switching device for switching the signals to be transmitted to the acoustic device between to signals of the monitor and the recording/reproducing signals. The abnormality of the equipments can be determined easily by comparing the sounds representing the operation conditions of equipments for controlling the plant operation and the sounds recorded in their normal conditions. (N.H.)

  18. Prioritizing equipment for replacement.

    Science.gov (United States)

    Capuano, Mike

    2010-01-01

    It is suggested that clinical engineers take the lead in formulating evaluation processes to recommend equipment replacement. Their skill, knowledge, and experience, combined with access to equipment databases, make them a logical choice. Based on ideas from Fennigkoh's scheme, elements such as age, vendor support, accumulated maintenance cost, and function/risk were used.6 Other more subjective criteria such as cost benefits and efficacy of newer technology were not used. The element of downtime was also omitted due to the data element not being available. The resulting Periop Master Equipment List and its rationale was presented to the Perioperative Services Program Council. They deemed the criteria to be robust and provided overwhelming acceptance of the list. It was quickly put to use to estimate required capital funding, justify items already thought to need replacement, and identify high-priority ranked items for replacement. Incorporating prioritization criteria into an existing equipment database would be ideal. Some commercially available systems do have the basic elements of this. Maintaining replacement data can be labor-intensive regardless of the method used. There is usually little time to perform the tasks necessary for prioritizing equipment. However, where appropriate, a clinical engineering department might be able to conduct such an exercise as shown in the following case study.

  19. Electromagnetic design calculation of the control rod drive mechanism

    International Nuclear Information System (INIS)

    Zhu Qirong; Zhu Jingchang

    1991-01-01

    Electromagnetic design calculation of the step-by-step magnetic jacking control rod drive mechanism includes magnetic field force calculation and design calculation of magnetomotive force for three electromagnetic iron and their coilds. The basic principle and method of electromagnetic design calculation had been expounded to take the lift magnet and lift coil for example

  20. Radioactive decontamination of equipment

    International Nuclear Information System (INIS)

    1982-03-01

    After a recall of some definitions relating to decontamination techniques and of the regulation into effect, the principles to be respected to arrange rationally work zones are quoted while insisting more particularly on the types of coatings which facilitate maintenance operations and the dismantling of these installations. Then, the processes and equipments to use in decontamination units for routine or particular operations are described; the list of recommended chemical products to decontaminate the equipment is given. The influence of these treatments on the state and the duration of life of equipments is studied, and some perfectible methods are quoted. In the appendix, are given: the limits of surface contamination accepted in the centers; a standard project which defines the criteria of admissible residual contamination in wastes considered as cold wastes; some remarks on the interest that certain special ventilation and air curtain devices for the protection of operators working on apparatus generating contaminated dusts [fr

  1. Permen dan Jelli Sebagai Produk Inovasi dari Pasak Bumi (Eurycoma longifolia Jack

    Directory of Open Access Journals (Sweden)

    Fatmir Edwar

    2015-06-01

    Full Text Available Pasak bumi (Eurycoma longifolia Jack merupakan salah satu jenis tumbuhan hutan tropis di Indonesia yang pemanfaatannya sebagai bahan baku dalam pembuatan obat baik yang modern maupun tradisional.  Pasak bumi mengandung senyawa erikomanon yang ampuh mengobati malaria dan senyawa kuasinoid serta alkaloid yang dapat menghambat pertumbuhan sel kanker. Pasak bumi juga mempunyai senyawa aktif flavonoid yang berfungsi untuk melindungi struktur sel, meningkatkan efektifitas vitamin C, anti inflamasi, mencegah keropos tulang, antioksidan, dan antibiotik. Penelitian ini bertujuan untuk membuat produk permen dan jelli dari bagian akar, batang, daun, ranting, dan kulit pasak bumi sehingga dapat meningkatkan nilai tambah dan memudahkan akses bagi masyarakat luas untuk mendapatkan khasiat zat aktif yang dikandung tumbuhan tersebut dalam bentuk produk inovatif.  Standard produk yang dihasilkan (permen dan jelli mengacu kepada SNI 3547.1:2008 tentang kembang gula keras dan SNI No. 3547.2:2008 tentang kembang gula lunak. Berdasarkan hasil pengujian permen, semua parameter yaitu kadar air, abu, gula, sukrosa, Zn, Hg, Pb, As, Angka Lempeng Total, Coliform, Ecoli, Salmonella dan Kapang/Khamir memenuhi syarat, kecuali untuk parameter Cu dengan nilai antara 3,48–8,17% tidak memenuhi standar yang dipersyaratkan yaitu maksimal 2%. Sedangkan produk jelli sebagian besar memiliki kadar air bervariasi antara 18,20–39,45% tidak memenuhi standar  yang dipersyaratkan maksimal 20%. Hasil dari penelitian ini dapat meningkatkan nilai tambah dan nilai jual dari tumbuhan pasak bumi berupa produk permen dan jelli yang memiliki cita rasa, keunggulan dan manfaat bagi kesehatan.ABSTRAKPasak bumi (Eurycoma longifolia Jack merupakan salah satu jenis tumbuhan hutan tropis di Indonesia yang pemanfaatannya sebagai bahan baku dalam pembuatan obat baik yang modern maupun tradisional.  Pasak bumi mengandung senyawa erikomanon yang ampuh mengobati malaria dan senyawa kuasinoid serta

  2. Equipment Operational Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

    2009-06-11

    The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

  3. Variations in otolith patterns, sizes and body morphometrics of jack mackerel Trachurus japonicus juveniles.

    Science.gov (United States)

    Kanaji, Y; Kishida, M; Watanabe, Y; Kawamura, T; Xie, S; Yamashita, Y; Sassa, C; Tsukamoto, Y

    2010-10-01

    Variations in otolith patterns, sizes and body morphometrics of jack mackerel Trachurus japonicus juveniles were investigated. Under transmitted light, translucent (W(t)) and opaque otoliths (W(o)) were detected in juveniles collected from Wakasa Bay between July 2005 and April 2006, whereas only opaque otoliths (G(o)) were detected in Goto-nada Sea individuals between May and June 2006. Three groups of juveniles were distinguished based on differences in hatch season, otolith size and growth history, and body morphometrics. As T. japonicus has different spawning seasons according to spawning grounds, each group was estimated to hatch in different waters. Juveniles with W(t) otoliths were considered to have stayed in coastal habitat longer, as the hatch area was estimated to be near Wakasa Bay. Juveniles with W(o) and G(o) otoliths appear to recruit to coastal waters at larger size, since their hatch areas were estimated to be far from each collection area. Larger otoliths of W(t) were attributed to otolith accretion after the second growth flexion, which was observed only for W(t) . Standard length of W(t) fish at the second otolith growth flexion was estimated to correspond to recruitment size to coastal rocky reefs in Wakasa Bay. Body morphometrics were correlated with otolith size after removing body size effect, suggesting that morphological variations of T. japonicus juveniles were also associated with the timing of recruitment to coastal habitat. © 2010 The Authors. Journal compilation © 2010 The Fisheries Society of the British Isles.

  4. Observed chlorine concentrations during Jack Rabbit I and Lyme Bay field experiments

    Science.gov (United States)

    Hanna, Steven; Chang, Joseph; Huq, Pablo

    2016-01-01

    As part of planning for a series of field experiments where large quantities (up to 20 tons) of pressurized liquefied chlorine will be released, observations from previous chlorine field experiments are analyzed to estimate the ranges of chlorine concentrations expected at various downwind distances. In five field experiment days during the summer 2010 Jack Rabbit I (JR I) field trials, up to two tons of chlorine were released and concentrations were observed at distances, x, from 25 to 500 m. In the 1927 Lyme Bay (LB) experiments, there were four days of trials, where 3-10 tons of chlorine were released in about 15 min from the back of a ship. Concentrations were sampled at LB from four ships sailing across the cloud path at downwind distances in the range from about 350 to 3000 m. Thus, the distances from which JR I concentrations were available slightly overlapped the LB distances. One-minute arc-maximum chlorine concentrations, C (g/m3), were analyzed from four JR I trials and two LB trials. Normalized concentrations (Cu/Q) were plotted versus x (m), where u (m/s) is measured wind speed at heights of 2-10 m and Q (g/s) is continuous mass release rate. It is found that the JR I and LB Cu/Q observations smoothly merge with each other and fall along a line with approximate slope of -2 at distances beyond about 200 m (i.e., Cu/Q is proportional to x-2). At x < 200 m, where dense gas effects are more important, the slope is less (about -1.5). Most of the data points are within a factor of two of the "best-fit" line.

  5. Evaluating the Feasibility of Five Candidate DNA Barcoding Loci for Philippine Lasianthus Jack (Lasiantheae: Rubiaceae).

    Science.gov (United States)

    Arshed, Muhammad Jefte C; Valdez, Marcos B; Alejandro, Grecebio Jonathan D

    2017-01-01

    The pantropical genus Lasianthus Jack is identified for high phenotypic plasticity making traditional taxonomic identification difficult. Having some members with important medicinal properties, a precise complimentary identification through DNA barcoding is needed for species delineation. In this study, 12 samples representing six Philippine Lasianthus species were used to determine the most efficient barcoding loci among the cpDNA markers ( mat K, rbc L, rps 16, and trn T-F) and nrDNA (ITS) based on the criteria of universality, discriminatory power, and resolution of species. The results revealed that ITS has the recommended primer universality, greatest interspecific divergences, and average resolution of species. Among the cpDNA markers, mat K and rbc L are recommended but with minimal resolution of species. While trn T-F showed moderate interspecific variations and resolution of Lasianthus species, rps 16 has the lowest interspecific divergence and resolution of species. Consequently, ITS is the potential ideal DNA barcode for Lasianthus species. ITS, mat K, and rps 16 markers have the excellent amplification and sequence qualityITS marker has the highest interspecific divergence with the maximum values, followed by mat K, rbc L, trn T-F, and rps 16, respectivelyAll markers except rps 16 yielded average resolution to Lasianthus speciesITS marker is the most ideal locus in terms of excellent universality, high interspecific discriminatory ability, and average species resolution. Abbreviations used: ITS: Internal Transcribe Spacer, mat K: maturase K, rbc L: ribulose-1,5-biphospahte-carboxylase, rps 16: ribosomal protein 16 small subunit gene.

  6. Fishery of the Green Jack Caranx caballus (Osteichytes: Carangidae in Las Perlas Archipelago, Pacific Panama

    Directory of Open Access Journals (Sweden)

    James M. Mair

    2012-09-01

    Full Text Available Green Jacks, Caranx caballus, are distributed along the Eastern Pacific coast. In Panama, C. caballus was heavily fished around Las Perlas Archipelago to sustain local markets until 2007, when the archipelago was declared a marine protected area. This first study in Panama, analyzed a sample of 4 990 individuals from Las Perlas, obtained monthly from June 2005 to June 2006, from landings at the central fish market. Average total length was 36.1±6.4cm and optimum length 38.9cm. Approximately 68% of fish lengths were within ±10% of the optimal length but only six (15% were considered mega-spawners. The von Bertalanffy parameters describe a long-lived and fast growing species, while mortality rates revealed that C. caballus is under high fishing pressure. Standard length at which half of the population is mature was 38.8cm, and the size at which individuals matured massively, 33cm. Only 10-13% of the fish were immature. C. caballus reproduces two to three times per year, with peaks in December, April, and probably September, and recruits to the population at least twice per year. Catch per unit effort (CPUE was best predicted by minimum annual values of the Multivariate ENSO/ LNSO Index (MEI (R²=0.54. Results show that C. caballus in Pacific Panama is overfished. We recommend the raising of the minimum capture/landing size of this species in order to increase the proportion of megaspawners in the population and guarantee the sustainability of this resource.

  7. Burn Severity Dominates Understory Plant Community Response to Fire in Xeric Jack Pine Forests

    Directory of Open Access Journals (Sweden)

    Bradley D. Pinno

    2016-04-01

    Full Text Available Fire is the most common disturbance in northern boreal forests, and large fires are often associated with highly variable burn severities across the burnt area. We studied the understory plant community response to a range of burn severities and pre-fire stand age four growing seasons after the 2011 Richardson Fire in xeric jack pine forests of northern Alberta, Canada. Burn severity had the greatest impact on post-fire plant communities, while pre-fire stand age did not have a significant impact. Total plant species richness and cover decreased with disturbance severity, such that the greatest richness was in low severity burns (average 28 species per 1-m2 quadrat and plant cover was lowest in the high severity burns (average 16%. However, the response of individual plant groups differed. Lichens and bryophytes were most common in low severity burns and were effectively eliminated from the regenerating plant community at higher burn severities. In contrast, graminoid cover and richness were positively related to burn severity, while forbs did not respond significantly to burn severity, but were impacted by changes in soil chemistry with increased cover at pH >4.9. Our results indicate the importance of non-vascular plants to the overall plant community in this harsh environment and that the plant community is environmentally limited rather than recruitment or competition limited, as is often the case in more mesic forest types. If fire frequency and severity increase as predicted, we may see a shift in plant communities from stress-tolerant species, such as lichens and ericaceous shrubs, to more colonizing species, such as certain graminoids.

  8. Charging equipment. Ladegeraet

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, E

    1981-09-17

    The invention refers to a charging equipment, particularly on board charging equipment for charging traction batteries of an electric vehicle from the AC mains supply, consisting of a DC converter, which contains a controlled power transistor, a switching off unloading circuit and a power transmitter, where the secondary winding is connected in series with a rectifier diode, and a smoothing capacitor is connected in parallel with this series circuit. A converter module is provided, which consists of two DC voltage converters, whose power transistors are controlled by a control circuit in opposition with a phase displacement of 180/sup 0/.

  9. Transcriptome resources and functional characterization of monoterpene synthases for two host species of the mountain pine beetle, lodgepole pine (Pinus contorta) and jack pine (Pinus banksiana)

    Science.gov (United States)

    2013-01-01

    Background The mountain pine beetle (MPB, Dendroctonus ponderosae) epidemic has affected lodgepole pine (Pinus contorta) across an area of more than 18 million hectares of pine forests in western Canada, and is a threat to the boreal jack pine (Pinus banksiana) forest. Defence of pines against MPB and associated fungal pathogens, as well as other pests, involves oleoresin monoterpenes, which are biosynthesized by families of terpene synthases (TPSs). Volatile monoterpenes also serve as host recognition cues for MPB and as precursors for MPB pheromones. The genes responsible for terpene biosynthesis in jack pine and lodgepole pine were previously unknown. Results We report the generation and quality assessment of assembled transcriptome resources for lodgepole pine and jack pine using Sanger, Roche 454, and Illumina sequencing technologies. Assemblies revealed transcripts for approximately 20,000 - 30,000 genes from each species and assembly analyses led to the identification of candidate full-length prenyl transferase, TPS, and P450 genes of oleoresin biosynthesis. We cloned and functionally characterized, via expression of recombinant proteins in E. coli, nine different jack pine and eight different lodgepole pine mono-TPSs. The newly identified lodgepole pine and jack pine mono-TPSs include (+)-α-pinene synthases, (-)-α-pinene synthases, (-)-β-pinene synthases, (+)-3-carene synthases, and (-)-β-phellandrene synthases from each of the two species. Conclusion In the absence of genome sequences, transcriptome assemblies are important for defence gene discovery in lodgepole pine and jack pine, as demonstrated here for the terpenoid pathway genes. The product profiles of the functionally annotated mono-TPSs described here can account for the major monoterpene metabolites identified in lodgepole pine and jack pine. PMID:23679205

  10. Transcriptome resources and functional characterization of monoterpene synthases for two host species of the mountain pine beetle, lodgepole pine (Pinus contorta) and jack pine (Pinus banksiana).

    Science.gov (United States)

    Hall, Dawn E; Yuen, Macaire M S; Jancsik, Sharon; Quesada, Alfonso Lara; Dullat, Harpreet K; Li, Maria; Henderson, Hannah; Arango-Velez, Adriana; Liao, Nancy Y; Docking, Roderick T; Chan, Simon K; Cooke, Janice Ek; Breuil, Colette; Jones, Steven Jm; Keeling, Christopher I; Bohlmann, Jörg

    2013-05-16

    The mountain pine beetle (MPB, Dendroctonus ponderosae) epidemic has affected lodgepole pine (Pinus contorta) across an area of more than 18 million hectares of pine forests in western Canada, and is a threat to the boreal jack pine (Pinus banksiana) forest. Defence of pines against MPB and associated fungal pathogens, as well as other pests, involves oleoresin monoterpenes, which are biosynthesized by families of terpene synthases (TPSs). Volatile monoterpenes also serve as host recognition cues for MPB and as precursors for MPB pheromones. The genes responsible for terpene biosynthesis in jack pine and lodgepole pine were previously unknown. We report the generation and quality assessment of assembled transcriptome resources for lodgepole pine and jack pine using Sanger, Roche 454, and Illumina sequencing technologies. Assemblies revealed transcripts for approximately 20,000 - 30,000 genes from each species and assembly analyses led to the identification of candidate full-length prenyl transferase, TPS, and P450 genes of oleoresin biosynthesis. We cloned and functionally characterized, via expression of recombinant proteins in E. coli, nine different jack pine and eight different lodgepole pine mono-TPSs. The newly identified lodgepole pine and jack pine mono-TPSs include (+)-α-pinene synthases, (-)-α-pinene synthases, (-)-β-pinene synthases, (+)-3-carene synthases, and (-)-β-phellandrene synthases from each of the two species. In the absence of genome sequences, transcriptome assemblies are important for defence gene discovery in lodgepole pine and jack pine, as demonstrated here for the terpenoid pathway genes. The product profiles of the functionally annotated mono-TPSs described here can account for the major monoterpene metabolites identified in lodgepole pine and jack pine.

  11. Experimental equipment, ch. 6

    International Nuclear Information System (INIS)

    Boomstra, F.; Hoogenboom, A.M.; Prins, C.M.; Strasters, B.A.; Vermeer, A.; Wit, P. de; Zwol, N.A. van.

    1977-01-01

    The experimental equipment in use at Utrecht university is discussed. Attention is paid to the tandem Van de Graaff accelerator and the 4MV and 1MV accelerators. The detection systems for gamma-ray spectroscopy are reviewed with emphasis on the compton-suppression spectrometer. The data-handling system used for experiments with the tandem is also briefly discussed

  12. Equipment gift to Monaco

    International Nuclear Information System (INIS)

    1970-01-01

    Research work at the Agency's Laboratory of Marine Radioactivity in Monaco, including that concerned with pollution of the sea, has been made more effective by its latest acquisition of equipment. This is a spectrophotometer donated by the Federal Republic of Germany. (author)

  13. Safeguards techniques and equipment

    International Nuclear Information System (INIS)

    1997-01-01

    The current booklet is intended to give a full and balanced description of the techniques and equipment used for both nuclear material accountancy and containment and surveillance measures, and for the new safeguards measure of environmental sampling. As new verification measures continue to be developed, the material in the booklet will be periodically reviewed and updated versions issued. (author)

  14. Equipping tomorrow's fire manager

    Science.gov (United States)

    Christopher A. Dicus

    2008-01-01

    Fire managers are challenged with an ever-increasing array of both responsibilities and critics. As in the past, fire managers must master the elements of fire behavior and ecology using the latest technologies. In addition, today’s managers must be equipped with the skills necessary to understand and liaise with a burgeoning group of vocal stakeholders while also...

  15. Electrical equipment design library

    International Nuclear Information System (INIS)

    1994-01-01

    This book guides the design supervision, construction order for electrical equipment. The contents of this library are let's use electricity like this, leading-in-pole and casual power, electric pole install below 300KVA, electric pole install below 301∼1000KVA, electric pole install exceed 1000KVA, rooftop install exceed 1000KVA, CUBICLE type, 154KV services. It adds an appendix.

  16. Orphee reactor experimental equipment

    International Nuclear Information System (INIS)

    1987-01-01

    Experimental equipment around the ORPHEE reactor is presented. The neutron source; and the spectrometers and sample environment (inelastic and quasi-elastic scattering, elastic scattering, spread scattering, small angle scattering) are described. An experiment proposal and reports guide is supplied [fr

  17. Seismic qualification of equipment

    International Nuclear Information System (INIS)

    Heidebrecht, A.C.; Tso, W.K.

    1983-03-01

    This report describes the results of an investigation into the seismic qualification of equipment located in CANDU nuclear power plants. It is particularly concerned with the evaluation of current seismic qualification requirements, the development of a suitable methodology for the seismic qualification of safety systems, and the evaluation of seismic qualification analysis and testing procedures

  18. Underground coal equipment

    Energy Technology Data Exchange (ETDEWEB)

    Chadwick, J.

    2002-12-01

    This paper reports on increasing automation and enhanced productivity on longwalls, new development cutting and bolting technologies and haulage systems. Amongst equipment discussed is DBT's Electra series EL3000 shearer, the Dosco LH1400 roadheader with onboard bolters, and Joy 12 CM30 continuous miners. 4 photos.

  19. Design by analysis of composite pressure equipment

    International Nuclear Information System (INIS)

    Durand, S.; Mallard, H.

    2004-01-01

    Design by analysis has been particularly pointed out by the european pressure equipment directive. Advanced mechanical analysis like finite element method are used instead of classical design by formulas or graphs. Structural behaviour can be understood by the designer. Design by analysis of metallic pressure equipments is widely used. Material behaviour or limits analysis is based on sophisticated approach (elasto-plastic analysis,..). Design by analysis of composite pressure equipments is not systematically used for industrial products. The difficulty comes from the number of information to handle. The laws of mechanics are the same for composite materials than for steel. The authors want to show that in design by analysis, the composite material approach is only more complete than the metallic approach. Mechanics is more general but not more complicated. A multi-material approach is a natural evolution of design by analysis of composite equipments. The presentation is illustrated by several industrial cases - composite vessel: analogy with metallic calculations; - composite pipes and fittings; - welding and bounding of thermoplastic equipments. (authors)

  20. Facile synthesis of highly branched jacks-like ZnO nanorods and their applications in dye-sensitized solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Sudhagar, P. [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of); Kumar, R. Saravana [R and D Department of Physics, Kongunadu Arts and Science College, Coimbatore 641 029, Tamilnadu (India); Jung, June Hyuk; Cho, Woohyung [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of); Sathyamoorthy, R. [R and D Department of Physics, Kongunadu Arts and Science College, Coimbatore 641 029, Tamilnadu (India); Won, Jongok [Department of Chemistry, Sejong University, Gwangjin-gu, Seoul 143-747 (Korea, Republic of); Kang, Yong Soo, E-mail: kangys@hanyang.ac.kr [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of)

    2011-09-15

    Graphical abstract: -- Abstract: Highly branched, jacks-like ZnO nanorods architecture were explored as a photoanode in dye-sensitized solar cells, and their photovoltaic performance was compared with that of branch-free ZnO nanorods photoanodes. The highly branched network and large pores of the jacks-like ZnO nanorods electrodes enhances the charge transport, and electrolyte penetration. Thus, the jacks-like ZnO nanorods DSSCs render a higher conversion efficiency of {eta} = 1.82% (V{sub oc} = 0.59 V, J{sub sc} = 5.52 mA cm{sup -2}) than that of the branch-free ZnO nanorods electrodes ({eta} = 1.08%, V{sub oc} = 0.49 V, J{sub sc} = 4.02 mA cm{sup -2}). The incident photon-to-current conversion efficiency measurements reveal that the jacks-like ZnO nanorods DSSCs exhibit higher internal quantum efficiency ({approx}59.1%) than do the branch-free ZnO nanorods DSSC ({approx}52.5%). The charge transfer resistances at the ZnO/dye/electrolyte interfaces investigated using electrochemical impedance spectroscopy showed that the jacks-like ZnO nanorods DSSC had high charge transfer resistance and a slightly longer electron lifetime, thus improving the solar-cell performance.

  1. The lodgepole × jack pine hybrid zone in Alberta, Canada: a stepping stone for the mountain pine beetle on its journey East across the boreal forest?

    Science.gov (United States)

    Lusebrink, Inka; Erbilgin, Nadir; Evenden, Maya L

    2013-09-01

    Historical data show that outbreaks of the tree killing mountain pine beetle are often preceded by periods of drought. Global climate change impacts drought frequency and severity and is implicated in the range expansion of the mountain pine beetle into formerly unsuitable habitats. Its expanded range has recently reached the lodgepole × jack pine hybrid zone in central Alberta, Canada, which could act as a transition from its historical lodgepole pine host to a jack pine host present in the boreal forest. This field study tested the effects of water limitation on chemical defenses of mature trees against mountain pine beetle-associated microorganisms and on beetle brood success in lodgepole × jack pine hybrid trees. Tree chemical defenses as measured by monoterpene emission from tree boles and monoterpene concentration in needles were greater in trees that experienced water deficit compared to well-watered trees. Myrcene was identified as specific defensive compound, since it significantly increased upon inoculation with dead mountain pine beetles. Beetles reared in bolts from trees that experienced water deficit emerged with a higher fat content, demonstrating for the first time experimentally that drought conditions benefit mountain pine beetles. Further, our study demonstrated that volatile chemical emission from tree boles and phloem chemistry place the hybrid tree chemotype in-between lodgepole pine and jack pine, which might facilitate the host shift from lodgepole pine to jack pine.

  2. Facile synthesis of highly branched jacks-like ZnO nanorods and their applications in dye-sensitized solar cells

    International Nuclear Information System (INIS)

    Sudhagar, P.; Kumar, R. Saravana; Jung, June Hyuk; Cho, Woohyung; Sathyamoorthy, R.; Won, Jongok; Kang, Yong Soo

    2011-01-01

    Graphical abstract: -- Abstract: Highly branched, jacks-like ZnO nanorods architecture were explored as a photoanode in dye-sensitized solar cells, and their photovoltaic performance was compared with that of branch-free ZnO nanorods photoanodes. The highly branched network and large pores of the jacks-like ZnO nanorods electrodes enhances the charge transport, and electrolyte penetration. Thus, the jacks-like ZnO nanorods DSSCs render a higher conversion efficiency of η = 1.82% (V oc = 0.59 V, J sc = 5.52 mA cm -2 ) than that of the branch-free ZnO nanorods electrodes (η = 1.08%, V oc = 0.49 V, J sc = 4.02 mA cm -2 ). The incident photon-to-current conversion efficiency measurements reveal that the jacks-like ZnO nanorods DSSCs exhibit higher internal quantum efficiency (∼59.1%) than do the branch-free ZnO nanorods DSSC (∼52.5%). The charge transfer resistances at the ZnO/dye/electrolyte interfaces investigated using electrochemical impedance spectroscopy showed that the jacks-like ZnO nanorods DSSC had high charge transfer resistance and a slightly longer electron lifetime, thus improving the solar-cell performance.

  3. Automated detection and mapping of crown discolouration caused by jack pine budworm with 2.5 m resolution multispectral imagery

    Science.gov (United States)

    Leckie, Donald G.; Cloney, Ed; Joyce, Steve P.

    2005-05-01

    Jack pine budworm ( Choristoneura pinus pinus (Free.)) is a native insect defoliator of mainly jack pine ( Pinus banksiana Lamb.) in North America east of the Rocky Mountains. Periodic outbreaks of this insect, which generally last two to three years, can cause growth loss and mortality and have an important impact ecologically and economically in terms of timber production and harvest. The jack pine budworm prefers to feed on current year needles. Their characteristic feeding habits cause discolouration or reddening of the canopy. This red colouration is used to map the distribution and intensity of defoliation that has taken place that year (current defoliation). An accurate and consistent map of the distribution and intensity of budworm defoliation (as represented by the red discolouration) at the stand and within stand level is desirable. Automated classification of multispectral imagery, such as is available from airborne and new high resolution satellite systems, was explored as a viable tool for objectively classifying current discolouration. Airborne multispectral imagery was acquired at a 2.5 m resolution with the Multispectral Electro-optical Imaging Sensor (MEIS). It recorded imagery in six nadir looking spectral bands specifically designed to detect discolouration caused by budworm and a near-infrared band viewing forward at 35° was also used. A 2200 nm middle infrared image was acquired with a Daedalus scanner. Training and test areas of different levels of discolouration were created based on field observations and a maximum likelihood supervized classification was used to estimate four classes of discolouration (nil-trace, light, moderate and severe). Good discrimination was achieved with an overall accuracy of 84% for the four discolouration levels. The moderate discolouration class was the poorest at 73%, because of confusion with both the severe and light classes. Accuracy on a stand basis was also good, and regional and within stand

  4. Analýza image produktu Jack Daniel´s Tennessee Fire na českém trhu

    OpenAIRE

    Papoušek, Jiří

    2015-01-01

    This Diploma Thesis focuses on a new alcoholic product in the Czech Republic - Jack Daniel's Tennessee Fire. It examines its popularity amongst consumers, its relation to other products in the range of the brand and to the main competitors of the other brands. For better interpretation of the results there is a questionnaire research. The aim of this work is the image analysis of this product in the Czech market and to offer potential recommendations for the brand in the future which come out...

  5. Chemical composition of the leaf essential oils of Murraya koenigii (L. Spreng and Murraya paniculata (L. Jack

    Directory of Open Access Journals (Sweden)

    Jasim Uddin Chowdhury

    2008-06-01

    Full Text Available The chemical composition of the leaf oils of Murraya koenigii (L. Spreng and M. paniculata (L. Jack from Bangladesh was studied by gas chromatography mass spectroscopy (GC-MS. M. koenigii oil contained 39 compounds of which the major is 3-carene (54.2% followed by caryophyllene (9.5%. Oil of M. paniculata contained 58 compounds of which the major are caryophyllene oxide (16.6%, b-caryophyllene (11.8%, spathulenol (10.2%, b-elemene (8.9%, germacrene D (6.9% and cyclooctene, 4-methylene-6-(1-propenylidene (6.4%. The compositions of both oils varied qualitatively and quantitatively.

  6. Neoarchean metamorphism recorded in high-precision Sm-Nd isotope systematics of garnets from the Jack Hills (Western Australia)

    Science.gov (United States)

    Eccles, K. A.; Baxter, E. F.; Mojzsis, S. J.; Marschall, H.; Williams, M. L.; Jercinovic, M. J.

    2013-12-01

    Studies of metasedimentary rocks from the Jack Hills, which host Earth's oldest known detrital minerals, have focused on zircon and occasionally monazite or xenotime, but no attention has been directed toward one of the most common mineral markers of metamorphism: garnet. Garnet can provide a record of the post-depositional, prograde metamorphic history of Archean metasedimentary rocks. Additionally, the use of a newly developed detrital garnet dating technique [1,2] may reveal information about pre-depositional metamorphism that could address lingering questions about the nature and timing of Earth's earliest tectonometamorphic events. Here we investigate garnet from the Jack Hills metasedimentary rocks to test whether they record in situ metamorphism or are a detrital relict of even older metamorphic events. We identified garnet in two bulk quartz-pebble conglomerate samples collected from the 'discovery' outcrop at Eranondoo Hill in the Jack Hills of Western Australia. Electron microprobe analyses of polished grains and SEM measurements of unpolished grain surfaces are consistent, revealing garnet composition indicative of a single generation/population of predominantly almandine-spessartine solid solution (~10-35% mole fraction spessartine). Compositional maps of garnet grains reveal little zoning and no discontinuities, most consistent with a single growth event. Dating Jack Hills' garnet via the Sm-Nd system is possible due to continued development of small sample analysis techniques, including running NdO+ TIMS analyses with Ta2O5 activator [3] permitting Ma for two point isochrons between clean garnet (Sm/Nd ≥ 1.0) and their leached inclusion populations [2]. Four grouped garnet grain separates from one sample yield preliminary dates of 2703.6×6.0Ma, 2612.4×6.0Ma, 2605.0×5.5Ma, and 2567.3×8.3Ma, while the second sample yielded a date of 2579.6×4.6 Ma (2σ). Compositional and geochronologic data indicate likely in situ garnet growth during a late

  7. Characterization of inclusions in terrestrial impact formed zircon: Constraining the formation conditions of Hadean zircon from Jack Hills, Western Australia

    Science.gov (United States)

    Faltys, J. P.; Wielicki, M. M.; Sizemore, T. M.

    2017-12-01

    Due to the discovery and subsequent geochemical analysis of Hadean terrestrial material (e.g. detrital zircon from Jack Hills, Western Australia), a dramatic paradigm shift has occurred in the hypothesized near surface conditions of the first 500 million years of Earth's evolution. From a hellish setting riddled with impactors and not fit for life to a much milder environment that may have been uniquely suitable for the origin of life. Geochemical analyses of these ancient materials have been used to suggest the presence of water at or near the surface as well as the existence of continental crust during the Hadean, both of which have been suggested as necessary for the origin of life. However, the intensity of extraterrestrial bombardment during the Hadean and the effects of such events on the origin of life remains poorly understood. Clearly, as evidenced by Phanerozoic impact events, extraterrestrial impactors have the potential to dramatically effect the environment, particularly the biosphere. Early Earth likely experienced multiple large impact events, as evidenced by the lunar record, however whether those impacts were sufficient to frustrate the origin of life remains an open question. Although multiple lines of evidence, including the inclusion population, suggest the formation of Hadean zircon from Jack Hills as crystallizing in an under-thrust environment from S-type magmas, a recent study has suggested their formation in an impact melt environment analogous to a portion of the Sudbury Igneous Complex at the Sudbury impact structure. To determine between these two formation scenarios we have under-taken an inclusion study of terrestrial impact formed zircon from four of the largest terrestrial impact structures (Sudbury, Canada; Manicouagan, Canada; Vredefort, South Africa; Morokweng, South Africa), to compare to the vast inclusion dataset that exists for Jack Hills zircon. Preliminary data suggests a different inclusion population, from Hadean zircon

  8. Debris flow from 2012 failure of moraine-dammed lake, Three Fingered Jack volcano, Mount Jefferson Wilderness, Oregon

    Science.gov (United States)

    Sherrod, David R.; Wills, Barton B.

    2014-01-01

    In the late spring or early summer of 2012, a flood emanated from a small moraine-dammed lake on the northeast flank of Three Fingered Jack in the Mount Jefferson Wilderness. Channel erosion or slope collapse breached the natural dam of the lake, leading to a sudden lowering of lake level by 2.8 m and discharge of 12,700 cubic meters (m3) of water. The resulting debris flow formed a bouldery deposit extending about 0.35 km downslope.

  9. Was Jack the Ripper a Slaughterman? Human-Animal Violence and the World’s Most Infamous Serial Killer

    Science.gov (United States)

    Knight, Andrew; Watson, Katherine D.

    2017-01-01

    Simple Summary The identity of Jack the Ripper remains one of the greatest unsolved crime mysteries in history. Jack was notorious both for the brutality of his murders and also for his habit of stealing organs from his victims. His speed and skill in doing so, in conditions of poor light and haste, fueled theories he was a surgeon. However, re-examination of a mortuary sketch from one of his victims has revealed several key aspects that strongly suggest he had no professional surgical training. Instead, the technique used was more consistent with that of a slaughterhouse worker. There were many small-scale slaughterhouses in East London in the 1880s, within which conditions were harsh for animals and workers alike. The brutalizing effects of such work only add to concerns highlighted by modern research that those who commit violence on animals are more likely to target people. Modern slaughterhouses are more humane in some ways but more desensitizing in others, and sociological research has indicated that communities with slaughterhouses are more likely to experience the most violent of crimes. The implications for modern animal slaughtering, and our social reliance on slaughterhouses, are explored. Abstract Hundreds of theories exist concerning the identity of “Jack the Ripper”. His propensity for anatomical dissection with a knife—and in particular the rapid location and removal of specific organs—led some to speculate that he must have been surgically trained. However, re-examination of a mortuary sketch of one of his victims has revealed several aspects of incisional technique highly inconsistent with professional surgical training. Related discrepancies are also apparent in the language used within the only letter from Jack considered to be probably authentic. The techniques he used to dispatch his victims and retrieve their organs were, however, highly consistent with techniques used within the slaughterhouses of the day. East London in the 1880s had

  10. Visual communication and terminal equipment

    International Nuclear Information System (INIS)

    Kang, Cheol Hui

    1988-06-01

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  11. Visual communication and terminal equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Cheol Hui

    1988-06-15

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  12. Heritability and complex segregation analysis of deafness in Jack Russell Terriers

    Directory of Open Access Journals (Sweden)

    Strain George M

    2007-11-01

    Full Text Available Abstract Background The association between patterns of pigmentation and deafness in the dog has a long-documented history, with reports dating back over one hundred years. Long suspected of having a genetic basis, the search for loci with a pronounced influence in the expression of hearing loss in the dog has yet to be successful. No studies in the dog to date have found a possible influence of a specific colour locus associated with deafness. The present study is intended to evaluate the heritability of deafness in the Jack Russell Terrier (JRT, characterize the mode of inheritance, and evaluate the existence of a sex, coat colour, or coat texture influence on the expression of sensorineural deafness. Results The estimation of heritability of deafness in the JRT was 0.22 when deafness was considered a binary (normal/deaf trait and 0.31 when deafness was considered a three-category (normal/unilateral/bilateral deafness. The influence of coat colour in the incidence of JRT deafness was statistically significant, indicating that dogs with more white are more likely to be deaf. The influence of sex or coat texture was not statistically significant in the incidence of JRT deafness. Complex segregation analysis revealed a model of a single locus with a large effect on the binary measure of hearing loss is not supported. Conclusion This is the first attempt, to our knowledge, to characterize a genetic component responsible for deafness in the JRT. The heritability of deafness in the JRT was found to be 0.22 and 0.31 considering deafness to be a two-category or three-category trait, respectively. There appears to be an influence of coat colour on the expression of deafness. In an attempt to characterize the mode of inheritance of deafness in the JRT, a model of a single locus with a large effect on hearing loss is not supported with this data. Further study is needed to determine if a single locus may be influencing deafness in the JRT. While the

  13. Hydraulic Shearing and Hydraulic Jacking Observed during Hydraulic Stimulations in Fractured Geothermal Reservoir in Pohang, Korea

    Science.gov (United States)

    Min, K. B.; Park, S.; Xie, L.; Kim, K. I.; Yoo, H.; Kim, K. Y.; Choi, J.; Yoon, K. S.; Yoon, W. S.; Lee, T. J.; Song, Y.

    2017-12-01

    Enhanced Geothermal System (EGS) relies on sufficient and irreversible enhancement of reservoir permeability through hydraulic stimulation and possibility of such desirable change of permeability is an open question that can undermine the universality of EGS concept. We report results of first hydraulic stimulation campaign conducted in two deep boreholes in fractured granodiorite geothermal reservoir in Pohang, Korea. Borehole PX-1, located at 4.22 km, was subjected to the injection of 3,907 m3 with flow rate of up to 18 kg/s followed by bleeding off of 1,207 m3. The borehole PX-2, located at 4.35 km, was subjected to the injection of 1,970 m3 with flow rate of up to 46 kg/sIn PX-1, a sharp distinct decline of wellhead pressure was observed at around 16 MPa of wellhead pressure which was similar to the predicted injection pressure to induce hydraulic shearing. Injectivity interpretation before and after the hydraulic shearing indicates that permanent increase of permeability was achieved by a factor of a few. In PX-2, however, injectivity was very small and hydraulic shearing was not observed due possibly to the near wellbore damage made by the remedying process of lost circulation such as using lost circulation material during drilling. Flow rate of larger than 40 kg/s was achieved at very high well head pressure of nearly 90 MPa. Hydraulic jacking, that is reversible opening and closure of fracture with change of injection pressure, was clearly observed. Although sharp increase of permeability due to fracture opening was achieved with elevated injection pressure, the increased permeability was reversed with decreased injection pressure.Two contrasting response observed in the same reservoir at two different boreholes which is apart only 600 m apart provide important implication that can be used for the stimulation strategy for EGS.This work was supported by the New and Renewable Energy Technology Development Program of the Korea Institute of Energy Technology

  14. Paleomagnetism and Anisotropy of Magnetic Susceptibility study of the Miocene Jack Springs Tuff (Nevada, USA)

    Science.gov (United States)

    Shields, S.; Petronis, M. S.; Pluhar, C. J.; Gordon, L.

    2014-12-01

    The mid-Miocene Jack Springs Tuff (JST) outcrops across the western Mina Deflection accommodation zone, west-central Nevada and into eastern California. Previously, the source location for the JST was unknown, yet recent studies northwest of Mono Lake, CA have identified a relatively un-rotated structural block in which to reference the paleomagnetic data. Although new studies have indicated that this block may be rotated up to 13º, we argue that the probable source area is located near the Bodie Hills, CA. At this site, the paleomagnetic reference direction is D = 353°, I = 43°, α95 = 7.7° (Carlson et al, 2013). Based on these data, the JST can be used to measure absolute vertical-axis rotation as well as enable reconstruction of the paleo-topography using the corrected anisotropy of magnetic susceptibility (AMS) data. A total of 19 sites were sampled to constrain Cenozoic to recent vertical axis rotation within the region and AMS experiments were conducted to determine the flow direction of the JST. Curie point estimates indicate that the JST ranges in titanium concentration from 0.042 to 1.10, indicating a low to moderate titanomagnetite phase (Akimoto, 1962). Demagnetization experiments reveal mean destructive fields of the NRM ranging between 15mT and 40mT suggesting that both multi-domain to pseudo-single domain grains are the dominant ferromagnetic phases that carry the remanence and AMS fabric. Preliminary paleomagnetic data yield stable single component demagnetization behavior for most sites that, after structural correction, indicate clockwise vertical axis rotation ranging from +20°± 10° to +60°± 11° between multiple fault blocks. The uncorrected AMS data yield oblate magnetic fabrics that can be used to infer the transport direction, source region, and paleovalley geometry of the JST. These data are tentatively interpreted to indicate west to east transport of the JST across the Mono Basin region into the Mina Deflection that was erupted and

  15. Establishment for Nuclear Equipment: Overview

    International Nuclear Information System (INIS)

    Pracz, J.

    2001-01-01

    Full text: The activity of ZdAJ in 2000 was focused on realisation of the Government-Ordered Project - 6/15 MeV Accelerator. The realisation was accomplished in two stages: - stage I should result in deriving principal operational parameters of the accelerator - stage 2 will result in full implementation of the control system providing optimum control of the equipment and automatic maintaining of its parameters. Within the frames of the first stage, a klystron modulator panel was finished and the design documentation of the mechanical supporting structure, the arm, accelerating structure, collimator and control panel were advanced. Manufacturing of the above sub-units in the workshop has started. In the frames of the Specific Project of the State Committee for Scientific Research, the improvement of Neptun lOPC accelerator was undertaken. The read-out of the monitor dose with atmospheric pressure and ambient temperature compensation has been introduced. New filters for equalising the photon and electron beam and new wedge filters have been designed. Changes in programming have been introduced, which improve the patient's safety by eliminating possible personnel errors and increase the accuracy of radiation fields read-out. In 2000 ZdAJ progressed in development of the Quality System conforming EN-ISO 9001 Standard by including the provisions of EN 46001 Standard. The Standard EN 46001: ''Quality Systems - Medical Equipment''. Detailed requirements related to application of EN ISO 9001 is an European Quality Standard extending the provisions of EN ISO 9001 Standard over the manufacturers of medical equipment. (author)

  16. Equipment cost optimization

    International Nuclear Information System (INIS)

    Ribeiro, E.M.; Farias, M.A.; Dreyer, S.R.B.

    1995-01-01

    Considering the importance of the cost of material and equipment in the overall cost profile of an oil company, which in the case of Petrobras, represents approximately 23% of the total operational cost or 10% of the sales, an organization for the optimization of such costs has been established within Petrobras. Programs are developed aiming at: optimization of life-cycle cost of material and equipment; optimization of industrial processes costs through material development. This paper describes the methodology used in the management of the development programs and presents some examples of concluded and ongoing programs, which are conducted in permanent cooperation with suppliers, technical laboratories and research institutions and have been showing relevant results

  17. X-ray equipment

    International Nuclear Information System (INIS)

    Redmayne, I.G.B.

    1988-01-01

    The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.)

  18. X-ray equipment

    Energy Technology Data Exchange (ETDEWEB)

    Redmayne, I.G.B.

    1988-01-06

    The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.).

  19. Tube for irradiation equipment

    International Nuclear Information System (INIS)

    Goehrich, K.; Vogt, H.

    1979-01-01

    This patent describes a tube for irradiation equipment for limiting an emergent beam, with a baseplate, possessing a central aperture, intended for attaching to the equipment, as well as four carrier plates, each of which possesses a limiting edge and a sliding edge located at right angles thereto. The carrier plates are located parallel to the baseplate, the limiting edge of each carrier plate resting against the sliding edge of the adjacent carrier plate and each of the two mutually opposite pairs of carrier plates being displaceable, parallel to the direction of its sliding edges and symmetrically to the center of the transmission aperture, for the purpose of continuously varying the transmission aperture defined by the limiting edges, during which displacement each of the displaced carrier plates carries with it the carrier plate, resting against the limiting edge of the former plate, parallel to the direction of the limiting edge of the latter plate. 8 claims

  20. Equipment for isotope diagnostics

    International Nuclear Information System (INIS)

    Platz, W.

    1976-01-01

    The invention concerns an improvement of equipment for isotope diagnostics allowing to mark special intensity ranges of the recorded measurements by means of different colors. For undisturbed operation it is of advantage to avoid electric circuits between movable and unmovable parts of the color recorder. According to the invention, long gear wheels of glass fiber-reinforced polyamide are used for these connections. (ORU) [de

  1. Soviet equipment flies in

    CERN Multimedia

    CERN PhotoLab

    1978-01-01

    End of February 1977 a Soviet Ilyushin-76 heavy freight aircraft landed at Cointrin airport having on board fifty large wire proprtional chambers and associated apparatus, together weighing 10 tons, supplied by the Joint Institute for Nuclear Research, Dubna, USSR. The equipment was for the CERN- Dubna-Munich-Saclay experiment NA4 on deep inelastic muon scattering being set up in the North Area of SPS. See Weekly Bulletin 11/78.

  2. Labelling of equipment dispensers.

    Science.gov (United States)

    Gray, D C

    1993-01-01

    A new labelling system for use on medical equipment dispensers is tested. This system uses one of the objects stored in each unit of the dispenser as the 'label', by attaching it to the front of the dispenser with tape. The new system was compared to conventional written labelling by timing subjects asked to select items from two dispensers. The new system was 27% quicker than the conventional system. Images Fig. 1 PMID:8110335

  3. Equipment Obsolescence Management Program

    Energy Technology Data Exchange (ETDEWEB)

    Redmond, J.

    2014-07-01

    Nuclear Power Plant (NPP) Operators are challenged with securing reliable supply channels for safety related equipment due to equipment obsolescence. Many Original Equipment Manufacturers (OEMs) have terminated production of spare parts and product life-cycle support. The average component life cycles are much shorter than the NPP design life, which means that replacement components and parts for the original NPP systems are not available for the complete design life of the NPPs. The lack or scarcity of replacement parts adversely affects plant reliability and ultimately the profitability of the affected NPPs. This problem is further compounded when NPPs pursue license renewal and approval for plant-life extension. A reliable and predictable supply of replacement co components is necessary for NPPs to remain economically competitive and meet regulatory requirements and guidelines. Electrical and I and C components, in particular, have short product life cycles and obsolescence issues must be managed pro actively and not reactively in order to mitigate the risk to the NPP to ensure reliable and economic NPP operation. (Author)

  4. Personal protective equipment

    International Nuclear Information System (INIS)

    2004-01-01

    This Practical Radiation Technical Manual is one of a series that has been designed to provide guidance on radiological protection for employers, radiation protection officers, managers and other technically competent persons who have responsibility for ensuring the safety of employees working with ionizing radiation. The Manual may be used with the appropriate IAEA Practical Radiation Safety Manuals to provide training, instruction and information for all employees engaged in work with ionizing radiation. Personal protective equipment (PPE) includes clothing or other special equipment that is issued to individual workers to provide protection against actual or potential exposure to ionizing radiations. It is used to protect each worker against the prevailing risk of external or internal exposure in circumstances in which it is not reasonably practicable to provide complete protection by means of engineering controls or administrative methods. Adequate personal protection depends on PPE being correctly selected, fitted and maintained. Appropriate training for the users and arrangements to monitor usage are also necessary to ensure that PPE provides the intended degree of protection effectively. This Manual explains the principal types of PPE, including protective clothing and respiratory protective equipment (RPE). Examples of working procedures are also described to indicate how PPE should be used within a safe system of work. The Manual will be of most benefit if it forms part of a more comprehensive training programme or is supplemented by the advice of a qualified expert in radiation protection. Some of the RPE described in this Manual should be used under the guidance of a qualified expert

  5. A Guide for Equipping Industrial Arts Facilities.

    Science.gov (United States)

    American Industrial Arts Association, Washington, DC. Equipment Guide Committee.

    A guide for planning new and revising existing industrial arts facilities which gives a listing of tools and equipment recommended for each of the major areas of instruction (automotive and power mechanics, ceramics, drafting, electronics, elementary, general shop, graphic arts, metalworking, plastics, and woodworking). General descriptions and…

  6. Seismic verification of nuclear plant equipment anchorage

    International Nuclear Information System (INIS)

    Lepiece, M.; Van Vyve, J.

    1991-01-01

    More than 60% of the electrical power of Belgium is generated by seven PWR nuclear power plants. For three of them, the electro-mechanical equipment had to be reassessed after ten years of operation, because the seismic requirements were upgraded from 0.1 g to 0.17 g free field ground acceleration. The seismic requalification of the active equipment was a critical problem as the classical methods were too conservative. The approach based on the use of the past experience on the seismic behavior of nonnuclear equipment, chosen and developed by the SQUG, had to be transposed to the Belgian N.P.P. The decision of the accept-ability of equipment relies heavily on the aseismatic capacity of anchorage. The Electrical Power Research Institute (EPRI) developed the procedure and guideline for the demonstration of the aseismatic adequacy of equipment anchorage in a cost-effective and consistent manner, to support the decision by Seismic Review Team. The field inspection procedure to identify the type of fasteners and detect their possible defects and the verification procedure developed to calculate the aseismatic capacity of equipment anchorage on the strength of fasteners, the aseismatic capacity of anchorage and the comparison of the capacity with the demand are reported. (K.I.)

  7. Development and simulation of the air-jack for emergency like a huge disaster; Kyujoyo eajakki no kaihatsu to sono simyureshon

    Energy Technology Data Exchange (ETDEWEB)

    Katsuyama, Kunihisa.; Ogata, Yuji.; Wada, Yuji. [National Institute for Resources and Environment, Tsukuba (Japan); Hashizume, Kiyoshi.; Nishida, Kenjiro. [Nippon Kayaku Corp., Tokyo (Japan)

    1999-02-28

    When a disaster is so huge like Kobe earthquake, every energy line is killed. Even if we want to help the sufferers, we have no energy to move machines to help them. As collapsed houses are very heavy, we need machines to remove collapsed stuff. Explosives include a lot of energy in themselves. So, an air-jack which has explosives inside was developed to remove collapsed stuff on suffered people. A simple air-jack was made and tested. One concrete block, 50cm x 50cm x 50cm, was lifted by the simple air-jack. A simulation of lifting the concrete block was carried out with a programme ANSYS on the super computer. (author)

  8. Preliminary results of the empirical validation of daily increments in otoliths of jack mackerel Trachurus symmetricus murphyi (Nichols, 1920 marked with oxytetracycline

    Directory of Open Access Journals (Sweden)

    Miguel Araya

    2003-12-01

    Full Text Available The frequency of microincrement formation in sagittae otoliths of jack mackerel Trachurus symmetricus was validated using experiments on captive fish. Adult jack mackerel were injected with a dose of 100 mg of oxytetracycline/kg of fish. A second injection was performed 30 days later. The fish were then sacrificed and their sagittae otoliths were extracted. Thin sections of the otoliths were prepared and observed through an epifluorescent microscope using ultraviolet light. Two fluorescent marks corresponding to the two injections were clearly visible. The average number of microincrements between the two fluorescent marks was 29 (n=10; S.D.=1.63 and the median was 29.3. The Wilcoxon signed-rank test indicated that this value was not significantly different from 30. This result indicates that microincrements in otoliths of adult jack mackerel of between 28.4 and 37.7 cm fork length are formed with a daily frequency.

  9. Biochemical components of seminal plasma and their correlation to the fresh seminal characteristics in Marwari stallions and Poitou jacks

    Directory of Open Access Journals (Sweden)

    Thirumala Rao Talluri

    2017-02-01

    Full Text Available Aim: To investigate various biochemical components of seminal plasma in Marwari stallions and Poitou Jacks and to find out their correlation with that of the seminal characteristics. Materials and Methods: In this study, semen was collected from six Marwari stallions and six Poitou jacks aged from 4 to 6 years and with known fertility status. The semen collection from the stallions were collected during the breeding season, i.e., between the months of April and June. From the collected semen ejaculates, we estimated the values of some biochemical components, viz., total protein content, total lipid content, and enzymes such as glutamic pyruvic transaminase (GPT, glutamic oxaloacetic transaminase (GOT, alkaline phosphatase (ALP, acid phosphatase (ACP, and lactate dehydrogenase (LDH as well as concentrations of glucose, cholesterol, total calcium (Ca, and phosphorus (P and correlations among different seminal parameters were statistically examined using the Pearson correlation coefficient. Results: In this study, we found positive correlations between semen volume as well as sperm concentration and GOT, GPT, ALP and ACP for both the group stallions. Significant correlation between motility and glucose, GOT and GPT could be an indication for their role metabolism and protection against free radicals to the spermatozoa. Conclusion: Based on the results, it is concluded that there is a positive correlation between some biochemical values such as glucose, Ca, ALP, and LDH and seminal parameters which play a key role in capacitation and onward movement of the spermatozoa.

  10. Materials division facilities and equipment

    International Nuclear Information System (INIS)

    Biest, O. v.d.

    1984-01-01

    The research activities of the Division at the Petten Establishment have the aims of characterising the properties of high temperature materials in industrial process environments and of understanding the structures involved in order to gain an insight into behavioural mechanisms. Metallic materials fall within the scope of the programme; the activities are, at present, almost entirely concerned with austenitic steels and nickel based alloys. Starting in 1984, advanced ceramic materials will be studied as well. The equipment available permits the study of mechanical properties in controlled gaseous environments, of the rates and mechanisms of corrosive reactions between materials and those environments, and of the surface and bulk structures by advanced physical techniques. Special preparation and treatment techniques are available. The Division has developed a Data Bank on high temperature alloys. It also operates an information Centre, the activities of which include the organisation of scientific meetings, the commissioning of ''state of the art'' studies on topics in the field of high temperature materials and their applications and the development of a inventory of current research activities in the field in Europe. This booklet is intended to present the facilities and services of the Division to the organizations which are interested in its programmes of work

  11. Alternatives Generation Analysis Long Length Contaminated Equipment Removal System Storage

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    Major pieces of Characterization sampling equipment are currently stored outdoors. This includes the Long Length Contaminated Equipment receiver trailer and transportation trailer. A decision is required to determine the preferred alternative for facilities to store and maintain this equipment. The Long Length Contaminated Equipment Removal System (LLCERS) consists of many tools, mechanisms, and controllers currently stored in various locations. Much of this equipment should be protected from the elements while being stored. Some of the LLCERS equipment should be protected with some kind of roof cover. This decision analysis is to determine the best alternative for weather protection for the large equipment requiring a cover. Additional details are included in Sections 2.0 and 5.0. Key assumptions used in this analysis are detailed in Section 3.2

  12. Mining face equipment

    Energy Technology Data Exchange (ETDEWEB)

    G, Litvinskiy G; Babyuk, G V; Yakovenko, V A

    1981-01-07

    Mining face equipment includes drilling advance wells, drilling using explosives on the contour bore holes, loading and transporting the crushed mass, drilling reinforcement shafts, injecting reinforcement compounds and moving the timber. Camouflet explosives are used to form relaxed rock stress beyond the mining area to decrease costs of reinforcing the mining area by using nonstressed rock in the advance well as support. The strengthening solution is injected through advanced cementing wells before drilling the contour bores as well as through radial cementing wells beyond the timbers following loading and transport of the mining debris. The advance well is 50-80 m.

  13. Coal ash monitoring equipment

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, C G; Wormald, M R

    1978-10-02

    The monitoring equipment is used to determine the remainder from combustion (ash slack) of coal in wagons designed for power stations. Next to the rails, a neutron source (252 Cf, 241 Am/Be) is situated, which irradiates the coal with neutrons at a known dose, which produces the reaction 27 Al (n ..gamma..) Al 28. The aluminium content is a measure of the remainder. The 1.78 MeV energy is measured downstream of the rail with a detector. The neutron source can only act in the working position of a loaded wagon.

  14. Management of Transportation Equipment.

    Science.gov (United States)

    1982-11-01

    Record% % %. "jP -M -. M LIh TRANSPORTATION MAENTKENAI4CE SHOP WORKLOAD CONTROL WORK CENTER SADR A-OR .a’* tLR 4.,R53 8114LM 0 o 251 50 75 100 125 ISO ...PDBP 06 7 4892 TRACTOR, WHEEL, INDUST, 14001-20000 PDBP 06 7 4893 TRACTOR, WHEEL, INDUST, 20001-27000 PDBP 06 7 4894 TRACTOR, WHEEL, INDUST, 27001 PDBP...27K TRACTOR, WHEEL, INDUST, 27001 PDBP & UP P-i LINE ITEM 07 LIGHTING AND POWER GENERATION EQUIPMENT 5110 T FLOODLIGHT ELEC FLOODLIGHT, ELEC, TRUCK

  15. Californium-252 Program Equipment Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Chattin, Fred Rhea [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wilson, Kenton [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ezold, Julie G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-12-01

    To successfully continue the 252Cf production and meet the needs of the customers, a comprehensive evaluation of the Building 7920 processing equipment was requested to identify equipment critical to the operational continuity of the program.

  16. Failure diagnosis aiding device for plant equipment

    International Nuclear Information System (INIS)

    Uhara, Yoshihiko.

    1990-01-01

    The present invention intends to improve the efficiency of trouble shooting for equipments of industrial plants such as nuclear power plants. The device of the present invention comprises an intelligence base and an inference mechanism base. The intelligence base comprises a rule base, an information storing section having a part frame and a working frame and a user's frame. The parts frame contains the failure rate on every parts and data on related operations. The working frame contains the importance and frequency of working. The user's frame contains parameters showing the extent of user's skills. The rule base, the parts frame and the working frame can be selected in accordance with the extent of the user's skill in the inference mechanism. With such a constitution, failures can be checked with the intelligence base in accordance with the knowledges for the failures of the equipments and the extent of user's skill by way of the inference mechanism. (I.S.)

  17. Lunar construction/mining equipment

    Science.gov (United States)

    Ozdemir, Levent

    1990-01-01

    For centuries, mining has utilized drill and blast as the primary method of rock excavation. Although this technique has undergone significant improvements, it still remains a cyclic, labor intensive operation with inherent safety hazards. Other drawbacks include damage to the surrounding ground, creation of blast vibrations, rough excavation walls resulting in increased ventilation requirements, and the lack of selective mining ability. Perhaps the most important shortcoming of drill and blast is that it is not conducive to full implementation of automation or robotics technologies. Numerous attempts have been made in the past to automate drill and blast operations to remove personnel from the hazardous work environment. Although most of the concepts devised look promising on paper, none of them was found workable on a sustained production basis. In particular, the problem of serious damage to equipment during the blasting cycle could not be resolved regardless of the amount of charge used in excavation. Since drill and blast is not capable of meeting the requirements of a fully automated rock fragmentation method, its role is bound to gradually decrease. Mechanical excavation, in contrast, is highly suitable to automation because it is a continuous process and does not involve any explosives. Many of the basic principles and trends controlling the design of an earth-based mechanical excavator will hold in an extraterrestrial environment such as on the lunar surface. However, the economic and physical limitations for transporting materials to space will require major rethinking of these machines. In concept, then, a lunar mechanical excavator will look and perform significantly different from one designed for use here on earth. This viewgraph presentation gives an overview of such mechanical excavator systems.

  18. Consolidation equipment for irradiated nuclear fuel channels

    International Nuclear Information System (INIS)

    Taguchi, M.; Komatsu, Y.; Ose, T.

    1989-01-01

    The authors have developed and put into use a new type of mechanical consolidation equipment for irradiated nuclear fuel channels. This includes round-slice cutting of the top 100mm of the fuel channel with a guillotine cutter, and press cutting of the two corners of the remaining length of the fuel channel. Four guillotine blades work in combination with receiving blades arranged inside the fuel channel to cut the top 100mm, including the clips and spacers, of the fuel channel into a round slice. A press assembled in the consolidation equipment then presses the slice to achieve volume reduction. The press cutting operation uses two press cutting blades arranged inside the fuel channel and the receiving blades outside the fuel channel. The remaining length of fuel channel is cut off into L-shaped pieces by press cutting. This consolidation equipment is highly efficient because the round-slice cutting, pressing, and press cutting are all achieved by one unit

  19. Irradiation position-control equipment for the HIMAC

    Energy Technology Data Exchange (ETDEWEB)

    Higashi, Seiichi; Kuma, Shoichiro [Mitsubishi Electric Corp., Tokyo (Japan); Nomura, Kazuaki; Endo, Masahiro; Minohara, Shin-ichi

    1995-02-01

    Use of heavy-ion beams to mount a pinpoint attack on unhealthy tissue requires that the target tissue be placed in the precise location specified by the therapy planning equipment. The article reports on the detailed specifications, positioning mechanism, position verification method and the interface with the therapy planning equipment. (author).

  20. Characterization equipment essential drawing plan

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered Support drawings until the Characterization Equipment Drawing Evaluation Report is completed

  1. Coal mining equipment

    International Nuclear Information System (INIS)

    Stein, R.R.; Martin, T.W.

    1991-01-01

    The word in longwall components is big, and these larger components have price tags to match. The logic behind the greater investment is that it will yield high production rates and good uptime statistics. This is true in most cases. More important than single-shift tonnage records, average shift production continues to climb upwards. This paper reports on the quality, and more significantly, the quantity of service supplied for long-wall equipment, which has reached levels that would have been seen as unachievable when longwall mining was first introduced in the U.S. The school of thought then was that longwall would increase productivity in part by reducing the number of production units and thus reducing the number of personnel employed underground. The expectation of fewer employees turned out to be unrealistic. That was probably one reason that some early attempts to install longwall system looked more like failures than vision of the future

  2. Reactor fuel charging equipment

    International Nuclear Information System (INIS)

    Wade, Elman.

    1977-01-01

    In many types of reactor fuel charging equipment, tongs or a grab, attached to a trolley, housed in a guide duct, can be used for withdrawing from the core a selected spent fuel assembly or to place a new fuel assembly in the core. In these facilities, the trolley may have wheels that roll on rails in the guide duct. This ensures the correct alignment of the grab, the trolley and fuel assembly when this fuel assembly is being moved. By raising or lowering such a fuel assembly, the trolley can be immerged in the coolant bath of the reactor, whereas at other times it can be at a certain level above the upper surface of the coolant bath. The main object of the invention is to create a fuel handling apparatus for a sodium cooled reactor with bearings lubricated by the sodium coolant and in which the contamination of these bearings is prevented [fr

  3. Chapter 12. Space Heating Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Rafferty, Kevin D.

    1998-01-01

    The performance evaluation of space heating equipment for a geothermal application is generally considered from either of two perspectives: (a) selecting equipment for installation in new construction, or (b) evaluating the performance and retrofit requirements of an existing system. With regard to new construction, the procedure is relatively straightforward. Once the heating requirements are determined, the process need only involve the selection of appropriately sized hot water heating equipment based on the available water temperature. It is important to remember that space heating equipment for geothermal applications is the same equipment used in non-geothermal applications. What makes geothermal applications unique is that the equipment is generally applied at temperatures and flow rates that depart significantly from traditional heating system design. This chapter presents general considerations for the performance of heating equipment at non-standard temperature and flow conditions, retrofit of existing systems, and aspects of domestic hot water heating.

  4. Effects of introgression on the genetic population structure of two ecologically and economically important conifer species: lodgepole pine (Pinus contorta var. latifolia) and jack pine (Pinus banksiana).

    Science.gov (United States)

    Cullingham, Catherine I; Cooke, Janice E K; Coltman, David W

    2013-10-01

    Forest trees exhibit a remarkable range of adaptations to their environment, but as a result of frequent and long-distance gene flow, populations are often only weakly differentiated. Lodgepole and jack pine hybridize in western Canada, which adds the opportunity for introgression through hybridization to contribute to population structure and (or) adaptive variation. Access to large sample size, high density SNP datasets for these species would improve our ability to resolve population structure, parameterize introgression, and separate the influence of demography from adaptation. To accomplish this, 454 transcriptome reads for lodgepole and jack pine were assembled using Newbler and MIRA, the assemblies mined for SNPs, and 1536 SNPs were selected for typing on lodgepole pine, jack pine, and their hybrids (N = 536). We identified population structure using both Bayesian clustering and discriminate analysis of principle components. Introgressed SNP loci were identified and their influence on observed population structure was assessed. We found that introgressed loci resulted in increased differentiation both within lodgepole and jack pine populations. These findings are timely given the recent mountain pine beetle population expansion in the hybrid zone, and will facilitate future studies of adaptive traits in these ecologically important species.

  5. Durable Reliability of Jack-up Platforms. The impact of Fatigue, Fracture and Effect of Extreme Environmental Loads on the Structural Reliability

    NARCIS (Netherlands)

    Shabakhty, N.

    2004-01-01

    A variety of factors is governing the operational conditions of jack-up platforms. The platforms are moved to different locations, which are causing changes in water depth, environmental and seabed conditions, drilling depths, payload etc. Insight should be gained in how the different factors affect

  6. Movable chain jacks and winches: case study of PETROBRAS' P58/)62and ENI's Goliat

    Energy Technology Data Exchange (ETDEWEB)

    Grindheim, Reidar [Aker Pusnes AS, Arendal (Norway)

    2012-07-01

    Recently, Aker Solutions delivered a movable chain jack system to PETROBRAS's P58/P62 FPSOs and a movable windlass system to ENI's Goliat FPSO. This paper highlights the main differences between the two systems and when it is beneficial to employ movable systems. There are many parameters to consider in determining which system to use - also a traditional system involving a single winch or chain jack per mooring line may in many cases be preferred. The movable chain jack concept is designed to operate multiple mooring lines within the same cluster. A single chain jack is lifted by a skidding gantry and moved to the next mooring line and so forth. Installation and messenger chains are moved using a large sliding chain locker allowing for later offloading of the surplus chain. The movable windlass system is also designed to operate multiple mooring lines within the same cluster. However, in this case the winch is rotary and can operate via electric or hydraulic power. One of the main considerations is to move the windlass and keep the mooring lines intact without cutting them. (author)

  7. Anti-inflammatory effect of ethanolic extract of spine, skin and rind of Jack fruit peel - A comparative study.

    Science.gov (United States)

    Meera, M; Ruckmani, A; Saravanan, R; Lakshmipathy Prabhu, R

    2017-10-09

    The present study was conducted to identify the chemical constituents and evaluate the anti-inflammatory activity of crude ethanolic extracts of spine, skin and rind of jack fruit (Artocarpus heterophyllus) peel. Polyphenol and flavonoid contents were assessed using Folin's Ciocalteu reagent and aluminium chloride methods which revealed 316, 355 and 382 mg tannic acid equivalent/g of polyphenol and 96.7, 131.6 and 164.6 mg quercetin equivalent/g of flavonoid in spine, skin and rind, respectively. Anti-inflammatory activity of all three extracts was comparable to diclofenac in vitro and in vivo studies. Skin exhibited maximum anti-inflammatory activity, rind had preferential inhibition on Cyclooxygenase-2 and spine and skin inhibited both Cyclooxygenase-1 and 2 in vitro.

  8. Chemical composition of the leaf essential oils of Murraya koenigii (L. Spreng and Murraya paniculata (L. Jack

    Directory of Open Access Journals (Sweden)

    Jasim Uddin Chowdhury

    2008-12-01

    Full Text Available The chemical composition of the leaf oils of Murraya koenigii (L. Spreng and M. paniculata (L. Jack from Bangladesh was studied by gas chromatography mass spectroscopy (GC-MS. M. koenigii oil contained 39 compounds of which the major is 3-carene (54.2% followed by caryophyllene (9.5%. Oil of M. paniculata contained 58 compounds of which the major are caryophyllene oxide (16.6%, beta-caryophyllene (11.8%, spathulenol (10.2%, beta-elemene (8.9%, germacrene D (6.9% and cyclooctene, 4-methylene-6-(1-propenylidene (6.4%. The composi-tions of both oils varied qualitatively and quantitatively.

  9. What can zircon ages from the Jack Hills detrital zircon suite really tell us about Hadean geodynamics?

    Science.gov (United States)

    Whitehouse, Martin; Nemchin, Alexander

    2015-04-01

    As the only direct sample of the Hadean Earth, detrital zircon grains from the Jack Hills, Western Australia, have been the subject of intense investigation over the almost three decades since their discovery. A wide variety of geochemical and isotopic analyses of these grains, as well as their mineral inclusions, have been used variously to support two fundamentally different models for Hadean geodynamics: (i) Some form of (not necessarily modern-style) plate recycling generating felsic (continental-type?) crust at the boundaries [1, 2], or conversely (ii) the persistence of a long-lived, stagnant basaltic lid within which magmatism occurred as a result of internal temperature perturbations and/or impacts [3, 4], a model also generally consistent with a wide range of observations from post-Hadean geochemical reservoirs. Despite the considerable time and resources expended, the majority of these studies uncritically accept the individual U-Pb zircon ages, even though their veracity is key to many of the interpretations [5, 6]. We report here the results of an in-depth evaluation of all published (and new) U-Pb ages from the Jack Hills zircon suite in order to define age populations that can be used with a high degree of confidence in geodynamic interpretations. A notable problem in the interpretation of U-Pb data from ancient zircon grains (including those as young as the Neoarchean) is that disturbance of the systematics even several 100 Ma after crystallization causes data to spread along the concordia curve without becoming discernably discordant within the relatively large error bounds associated with U/Pb ages from in situ dating methods (e.g. SIMS). While 207Pb/206Pb ages are typically more precise, individually they provide no means to detect Pb-loss-induced younging. However, if two or preferably more analyses have been made in the same zircon growth zone, a reasonable evaluation of the possibility of Pb-loss can be made. In the available Jack Hills zircon

  10. Eurycomanone and Eurycomanol from Eurycoma longifolia Jack as Regulators of Signaling Pathways Involved in Proliferation, Cell Death and Inflammation

    Directory of Open Access Journals (Sweden)

    Shéhérazade Hajjouli

    2014-09-01

    Full Text Available Eurycomanone and eurycomanol are two quassinoids from the roots of Eurycoma longifolia Jack. The aim of this study was to assess the bioactivity of these compounds in Jurkat and K562 human leukemia cell models compared to peripheral blood mononuclear cells from healthy donors. Both eurycomanone and eurycomanol inhibited Jurkat and K562 cell viability and proliferation without affecting healthy cells. Interestingly, eurycomanone inhibited NF-κB signaling through inhibition of IκBα phosphorylation and upstream mitogen activated protein kinase (MAPK signaling, but not eurycomanol. In conclusion, both quassinoids present differential toxicity towards leukemia cells, and the presence of the α,β-unsaturated ketone in eurycomanone could be prerequisite for the NF-κB inhibition.

  11. 14 CFR 91.503 - Flying equipment and operating information.

    Science.gov (United States)

    2010-01-01

    ... Turbine-Powered Multiengine Airplanes and Fractional Ownership Program Aircraft § 91.503 Flying equipment...) Emergency operation of fuel, hydraulic, electrical, and mechanical systems. (2) Emergency operation of...

  12. THE FEATURES OF TRAVELER WITH VACUUM AND SUCTION EQUIPMENT

    Directory of Open Access Journals (Sweden)

    H. L. Moroz

    2008-11-01

    Full Text Available The analysis of real mechanical system of the bridge crane with vacuum-sucker equipment is made and the design scheme for the mathematical model of dynamic processes created on the basis of the analysis is offered.

  13. Equipment repair in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, S

    1982-01-01

    Most equipment in Chinese coal mines consists of machinery and equipment produced in the 1950s; the efficiency of 4-62, CTD-57 and 70B/sub 2/ ventilators is 15% lower than that of new ones; that of SSM and AYaP pumps, 10% lower than of modern ones. Equipment renovation is done in three ways: replacing obsolete equipment with new equipment of the same type; improving the performance of existing equipment by introducing efficiency and reconstruction; and replacing obsolete equipment with advanced equipment. It is indicated that the second way, for example, replacement of 4-62 ventilator blades with a maximum efficiency of 73% by 4-72 ventilator blades raises its efficiency to 90%. Replacing the 8DA-8x3 water pump, having a maximum efficiency of 63%, with the 200D 43x3 pump with a maximum efficiency of 78%, enables an electricity savings of 7000 yuan per year, which exceeds all replacement costs (600 yuan). The need to improve equipment maintenance and preventive work to increase equipment service life and to introduce new techniques and efficiency is noted.

  14. Fatty Acid Composition of Novel Host Jack Pine Do Not Prevent Host Acceptance and Colonization by the Invasive Mountain Pine Beetle and Its Symbiotic Fungus

    Science.gov (United States)

    Ishangulyyeva, Guncha; Najar, Ahmed; Curtis, Jonathan M.

    2016-01-01

    Fatty acids are major components of plant lipids and can affect growth and development of insect herbivores. Despite a large literature examining the roles of fatty acids in conifers, relatively few studies have tested the effects of fatty acids on insect herbivores and their microbial symbionts. Particularly, whether fatty acids can affect the suitability of conifers for insect herbivores has never been studied before. Thus, we evaluated if composition of fatty acids impede or facilitate colonization of jack pine (Pinus banksiana) by the invasive mountain pine beetle (Dendroctonus ponderosae) and its symbiotic fungus (Grosmannia clavigera). This is the first study to examine the effects of tree fatty acids on any bark beetle species and its symbiotic fungus. In a novel bioassay, we found that plant tissues (hosts and non-host) amended with synthetic fatty acids at concentrations representative of jack pine were compatible with beetle larvae. Likewise, G. clavigera grew in media amended with lipid fractions or synthetic fatty acids at concentrations present in jack pine. In contrast, fatty acids and lipid composition of a non-host were not suitable for the beetle larvae or the fungus. Apparently, concentrations of individual, rather than total, fatty acids determined the suitability of jack pine. Furthermore, sampling of host and non-host tree species across Canada demonstrated that the composition of jack pine fatty acids was similar to the different populations of beetle’s historical hosts. These results demonstrate that fatty acids composition compatible with insect herbivores and their microbial symbionts can be important factor defining host suitability to invasive insects. PMID:27583820

  15. Design and construction of a air pollutant gases sampler equipment

    International Nuclear Information System (INIS)

    Gomez S, R.A.; Rodriguez, T.J.

    1996-01-01

    This thesis is about the sketch and construction of an equipment which samples contaminated gases in the air. The topic of this work, is to propose a solution for imported and national equipment. The solution consist on lower prices of imported and national equipment without loosing the accuracy and the precision of those now available. The investigation shows all process to sample gases and theirs measurement for which all the mechanical, electric and electronic equipment, and the necessary software for giving the results in a computerized way were outlined. With this work it was able to succeed in measurements with a national low price, accurate, reliable, programmable, completely automatic and easy to use. This equipment exceed in accuracy the Japanese and the american equipment

  16. 21 CFR 866.4540 - Immunonephelometer equipment.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4540 Immunonephelometer equipment. (a) Identification. Immunonephelometer equipment for clinical use...

  17. 21 CFR 866.4520 - Immunofluorometer equipment.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4520 Immunofluorometer equipment. (a) Identification. Immunofluorometer equipment for clinical use with...

  18. Material Handling Equipment Evaluation for Crater Repair

    Science.gov (United States)

    2016-11-01

    lifting (www.mcneiluscompanies.com). Agricultural/Mechanical Industry. The final equipment solution investigated was a telescoping boom crane (see... crane include: • Trailer-tongue mounting would provide for self-contained lifting capabilities on the simplified volumetric mixer. • Some models are...jib crane could potentially be effective as integrating lifting capabilities with the current simplified volumetric mixer. Both options could be

  19. Equipment standards for interventional cardiology

    International Nuclear Information System (INIS)

    Dowling, A.; Gallagher, A.; Walsh, C.; Malone, J.

    2005-01-01

    Interventional radiology has seen rapid growth in cardiology and represents an alternative to hazardous surgery. Recently there has been a substantial growth in the number of procedures being performed and interventional cardiology (IC) procedures are the most common interventional procedures in Europe. Advances in imaging technology have facilitated the development of increasingly complex radiological IC equipment. Currently, the technology is developing at a rate ahead of supporting research, equipment standards and a regulatory framework. International standards play a key role in the design, manufacture and performance of radiological IC equipment. A survey of 12 IC systems (15 imaging chains) was conducted in Irish hospitals. The aim of the study was to assess the imbalance between rapidly advancing technology and existing standards and to propose recommendations for new IC equipment standards. The results demonstrate the need for definitive equipment requirements and standardisation in the design, manufacture, acceptance and maintenance of IC equipment. (authors)

  20. Generation of equipment response spectrum considering equipment-structure interaction

    International Nuclear Information System (INIS)

    Lee, Sang Hoon; Yoo, Kwang Hoon

    2005-01-01

    Floor response spectra for dynamic response of subsystem such as equipment, or piping in nuclear power plant are usually generated without considering dynamic interaction between main structure and subsystem. Since the dynamic structural response generally has the narrow-banded shapes, the resulting floor response spectra developed for various locations in the structure usually have high spectral peak amplitudes in the narrow frequency bands corresponding to the natural frequencies of the structural system. The application of such spectra for design of subsystems often leads to excessive design conservatisms, especially when the equipment frequency and structure are at resonance condition. Thus, in order to provide a rational and realistic design input for dynamic analysis and design of equipment, dynamic equipment-structure interaction (ESI) should be considered in developing equipment response spectrum which is particularly important for equipment at the resonance condition. Many analytical methods have been proposed in the past for developing equipment response spectra considering ESI. However, most of these methods have not been adapted to the practical applications because of either the complexities or the lack of rigorousness of the methods. At one hand, mass ratio among the equipment and structure was used as an important parameter to obtain equipment response spectra. Similarly, Tseng has also proposed the analytical method for developing equipment response spectra using mass ratio in the frequency domain. This method is analytically rigorous and can be easily validated. It is based on the dynamic substructuring method as applied to the dynamic soil-structure interaction (SSI) analysis, and can relatively easily be implemented for practical applications without to change the current dynamic analysis and design practice for subsystems. The equipment response spectra derived in this study are also based on Tseng's proposed method

  1. Problems associated with accelerated thermal aging of electrical equipment

    International Nuclear Information System (INIS)

    Isgro, J.R.

    1984-01-01

    This paper discusses the potential problems that may be experienced when accounting for aging mechanisms in organic polymers when utilizing accelerated thermal aging techniques for electrical equipment qualification. Included are discussions of actual experiences and problems encountered in the qualification of electrical and electronic equipment for a complete nuclear power plant. The wide variety of approaches to thermal accelerated aging by various manufacturers of diverse equipment types provides depth to the discussion. A description of how to account for aging mechanisms is also presented

  2. Overall Equipment Effectiveness Implementation Criteria

    Science.gov (United States)

    Abramova, I. G.; Abramov, D. A.

    2018-01-01

    This article documents the methods applied in production control technics specifically focused on commonly used parameter OEE (Overall Equipment Effectiveness). The indicators of extensive and intensive use of equipment are considered. Their appointment this is comparison in the same type of production within the industry and comparison of single-type and / or different types of equipment in terms of capacity. However, it is shown that there is no possibility of revealing the reasons for the machine’s operation: productive / unproductive, with disturbances. Therefore, in the article reveals the approaches to calculating the indicator characterizing the direct operation of the equipment. The Machine Load coefficient is approaching closely to the indicator of the efficiency of the use of equipment. Methods analysis is proceeded through the historically applied techniques such as “Stopwatch” and “Motion” studies. Was performed the analysis of the efficiency index of OEE equipment using the comparable indexes performance of equipment in the Russian practice. An important indicator of OEE contains three components. The meaning of each of them reflects historically applicable indicators. The value of the availability of equipment indicator is close to the value of the equipment extensibility index. The value of the indicator of the efficiency of work can be compared with the characteristic of the capacity of the equipment and the indicator of the quality level can meet the requirements for compliance with the manufacturing technology. Shown that the sum of the values of the coefficient of “Availability” of the equipment and the value of the “Factor of compaction of working hours” are one. As well as the total value of the indicator “level of quality” and the coefficient of marriage given in the result unit. The measurability of the indicators makes it possible to make a prediction about efficiency of the equipment.

  3. Information technology equipment cooling system

    Science.gov (United States)

    Schultz, Mark D.

    2014-06-10

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools warm air generated by the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat from the rack of information technology equipment.

  4. Management methodology for pressure equipment

    Science.gov (United States)

    Bletchly, P. J.

    Pressure equipment constitutes a significant investment in capital and a major proportion of potential high-risk plant in many operations and this is particularly so in an alumina refinery. In many jurisdictions pressure equipment is also subject to statutory regulation that imposes obligations on Owners of the equipment with respect to workplace safety. Most modern technical standards and industry codes of practice employ a risk-based approach to support better decision making with respect to pressure equipment. For a management system to be effective it must demonstrate that risk is being managed within acceptable limits.

  5. Cryogenic equipment; Materiel cryogenique

    Energy Technology Data Exchange (ETDEWEB)

    Leger, L; Javellaud, J; Caro, C; Gilguy, R; Testard, O

    1966-06-01

    The cryostats presented here were built from standard parts; this makes it possible to construct a great variety of apparatus at minimum cost. The liquid nitrogen and helium reservoirs were designed so as to reduce losses to a minimum, and so as to make the cryostats as autonomous as possible. The experimental enclosure which is generally placed in the lower part of the apparatus requires a separate study in every case. Furthermore, complete assemblies such as transfer rods, isolated traps and high vacuum valves, were designed with a similar regard for the economic aspects and for the need for standardization. This equipment thus satisfies a great variety of experimental needs; it is readily adaptable and the consumptions of helium and liquid nitrogen are very low. (authors) [French] De nombreuses experiences utilisant les basses temperatures, necessitent l'emploi d'un materiel cryogenique complexe n'existant pas dans le commerce. Les cryostats presentes ici ont ete realises a partir d'elements standard, ce qui permet, malgre la diversite des appareils, de realiser un ensemble a moindre frais. Les reservoirs d'azote et d'helium liquides ont ete concus de facon a limiter les pertes et a conferer au cryostat la plus grande autonomie possible. L'enceinte experimentale situee en general dans la partie inferieure de l'appareil necessite dans tous les cas une etude speciale. D'autre part des ensembles complets tels que les cannes de transfert, piege isole, robinet pour vide secondaire, ont ete concus dans le meme souci de rentabilite et de standardisation. Ce materiel peut donc repondre a un grand nombre d'exigences experimentales, il est facilement adaptable, et les consommations d'helium et d'azote liquide sont tres reduites. (auteurs)

  6. Ageing management and equipment qualification

    International Nuclear Information System (INIS)

    Stahl, Gunnar

    2014-01-01

    The knowledge of how the environment and load of organic material in general and especially polymers and lubricants, is affecting the degradation of important properties, have increased during the last decade. However the restrictions using established additives like some color pigments due to their poisonousness e.g. pigments based at cadmium, lead, mercury etc. have caused problems when replacing additives to polymers. The replacement additives have often been used in new design without going through the required material qualification procedure. There have also been observed that some non-qualified and non-approved materials have been installed in some power plants due to false documentation. There are also a lot of new manufacturers, of materials similar to the previously qualified materials, active at the market. This increases the difficulty to ensure that the required material quality is used. New materials, new additives and new manufacturers makes if more and more difficult to assure that the expected material is present. This causes more strict demands of how the new materials often used in equipment at type-testing and in replacement materials are analyzed and documented. By implementing new steps for chemical, mechanical and electrical analysis and increase the general quality assurance content this issue can be managed. (authors)

  7. Equipment selection for atmospheric drying

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, P D; Bhattacharyya, S [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    Heavy water management is a major factor in deciding the economics of the PHWRs. Hence it is necessary to have an efficient recovery system, for the heavy water vapour escaping from various process systems and maintain a dry atmosphere in the recovery areas. While the basic objective of the atmospheric drying system is to maximize recovery and to minimize stack losses, it is equally important to optimally design the system with due consideration to operational and maintenance aspects. At present, heavy water vapour recovery in the existing Nuclear Power Plants (NPPs) is carried out by dryers of dual fixed bed design. While moving bed design could have some advantages, this has not been adopted so far because of the cumbersome mechanical design involved and special requirements for nuclear application. Developmental work done in this direction has resulted in compact alternative designs. In one of the designs, the change over from adsorption to regeneration is achieved by rotating the bed slowly. This concept is further refined in another alternative using a dessicant wheel. This paper contains brief equipment description of different designs; enumerates the design requirements of an atmospheric drying system for reactor building; describes steps for designing fixed bed type D{sub 2}O vapour recovery system, and highlights advances in dryer technology. (author). 2 refs., 4 figs., 1 ill.

  8. Handbook of Equipment Repair.

    Science.gov (United States)

    1981-05-14

    state of leapin- fn’rw.rd. Tn recent years, many mechanical repair workers often write and ask us to reprint the book. In our consideration, however...ast 4iron 1. .-eat _--OSIS-RTS 5.5 . . 4-5 t4- cast -3.01 -6 ~.0 ’ ɘ.᝱ 5,,:e j?24 2 * 10- 5 aron C l 50 S lcon : Ielt rSSIS-RQTS-s;.4 u a 2.47 5at- .0

  9. 22 CFR 135.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  10. 21 CFR 1403.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  11. 45 CFR 602.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  12. 49 CFR 18.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  13. 34 CFR 80.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  14. 10 CFR 600.232 - Equipment.

    Science.gov (United States)

    2010-01-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  15. 45 CFR 1183.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...

  16. Food Service Equipment and Appurtenances.

    Science.gov (United States)

    National Sanitation Foundation, Ann Arbor, MI.

    Equipment design specifications are presented relating to tables of all kinds, counters, sinks and drainboards, bins, shelves, drawers, hoods and similar kitchen appurtenances, not including baking, roasting, toasting, broiling or frying equipment, food preparation machinery such as slicers, choppers, and cutters, mixers and grinders, steam…

  17. Equipe de trabalho

    Directory of Open Access Journals (Sweden)

    Gabriel Gerber Hornink

    2014-08-01

    Full Text Available   Equipe de Trabalho 2014 1. Equipe editorial Editor-Chefe Bayardo Bapstista Torres, Instituto de Química - USP, Brasil Eduardo Galembeck, Departamento de Bioquímica Instituto de Biologia UNICAMP, Brasil   Editores Gabriel Gerber Hornink, Depto. Bioquímica, Instituto de Ciências Biomédicas, Universidade - Federal de Alfenas - Unifal-MG, Brasil Vera Maria Treis Trindade, Instituto de Ciências Básicas da Saúde, Departamento de Bioquímica, Universidade Federal do Rio Grande do Sul, Brasil   Corpo Editorial Adriana Cassina, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Angel Herráez, Departamento de Bioquímica y Biología molecular, Universidad de Alcalá de Henares, Madrid, Espanha André Amaral Gonçalves Bianco, Universidade Federal de São Paulo (Unifesp, Brasil Denise Vaz de Macedo, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Eneida de Paula, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Guilherme Andrade Marson, Instituto de Química - USP, Brasil Jose Antonio Martinez Oyanedel, Universidad de Concepción, Chile Josep Maria Fernández Novell, Dept. Bioquímica i Biologia Molecular Universitat de Barcelona, Espanha Leila Maria Beltramini, Instituto de Física de São Carlos, Universidade Estadual de São Paulo - USP, Brasil Manuel João da Costa, Escola de Ciências da Saúde, Universidade do Minho, Portugal Maria Lucia Bianconi, Instituto de Bioquímica Médica Universidade Federal do Rio de Janeiro (UFRJ, Brasil María Noel Alvarez, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Miguel Ángel Medina Torres, Department of Molecular Biology & Biochemistry Faculty of Sciences University of Málaga, Espanha Nelma Regina Segnini Bossolan, Instituto de Física de São Carlos, Universidade de São Paulo - USP, Brasil Paulo De Avila

  18. Information technology equipment cooling method

    Science.gov (United States)

    Schultz, Mark D.

    2015-10-20

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools air utilized by the rack of information technology equipment to cool the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat generated by the rack of information technology equipment.

  19. Equipment for the emplacement of heat-producing waste in long horizontal boreholes

    International Nuclear Information System (INIS)

    Young, K.D.; Scully, L.W.; Fisk, A.; deBakker, P.; Friant, J.; Anderson, A.

    1983-01-01

    Emplacement of heat-producing waste in long horizontal holes may offer several technical and economic advantages over shallow vertical hole emplacement. Less of the host rock suffers damage as a result of drift construction; the heat from the waste can be isolated from the access drifts for long periods of time; and the amount of rock which must be excavated is much less than in traditional disposal scenarios. One of the major reasons that has been used to reject the long hole concept in the past and adhere to the shallow vertical hole concept is the equipment required to drill the holes and to emplace and retrieve the waste. Such equipment does not currently exist. It clearly is more difficult to drill a 600 to 1000 foot horizontal hole, possibly 3 to 4 feet in diameter, and place a canister of waste at the end of it than to drill a 30 foot vertical hole and lower the waste to the bottom. A liner, for emplacement hole stabilization, appears to be feasible by adapting existing technology for concrete slip forming or jacking in a steel liner. The conceptual design of the equipment to drill long horizontal holes, emplace waste and retrieve waste will be discussed. Various options in concept will be presented as well as their advantages and disadvantages. The operating scenario of the selected concept will be described as well as solutions to potential problems encountered

  20. Equipment for the emplacement of heat-producing waste in long horizontal boreholes

    International Nuclear Information System (INIS)

    Young, K.D.; Fisk, A.; Friant, J.; Scully, L.W.

    1983-01-01

    Emplacement of heat-producing waste in long horizontal holes may offer several technical and economic advantages over shallow vertical hole emplacement. Less of the host rock suffers damage as a resul of drift construction; the heat from the waste can be isolated from the access drifts for long periods of time; and the amount of rock which must be excavated is much less than in traditional disposal scenarios. One of the major reasons that has been used to reject the long hole concept in the past and adhere to the shallow vertical hole concept is the equipment required to drill the holes and to emplace and retrieve the waste. Such equipment does not currently exist. It clearly is more difficult to drill a 600 to 100 foot horizontal hole, possibly 3 to 4 feet in diameter, and place a canister of waste at the end of it than to drill a 30 foot vertical hole and lower the waste to the bottom. A liner, for emplacement hole stabilization, appears to be feasible by adapting existing technology for concrete slip forming or jacking in a steel liner. The conceptual design of the equipment to drill long horizontal holes, emplace waste and retrieve waste is discussed. Various options in concept are presented as well as their advantages and disadvantages. The operating scenario of the selected concept is described as well as solutions to potential problems encountered

  1. Lessons learned in testing of Safeguards equipment

    International Nuclear Information System (INIS)

    Pepper, Susan; Farnitano, Michael; Carelli, Joseph

    2001-01-01

    Full text: During the 1990s, the IAEA Department of Safeguards began a transition from analog to digital equipment. This included surveillance equipment, seals, NDA measurement systems, and other instruments. The transition to digital equipment was intended to facilitate compatibility between and integration of instruments, remote communication of data, improved data storage, and modernization. Many of the instruments are designed to operate on battery power during loss of facility power, and therefore, are designed to consume minimal power. In 2000, the IAEA experienced a number of failures in digital image surveillance (DIS) equipment. A study of the performance data revealed that the failures occurred in 'high risk' environments where the systems were exposed to neutrons. As a supporter of IAEA equipment development and implementation, the U.S. Support Program worked with the IAEA, the equipment designer, and the equipment manufacturer in special meetings on DIS to determine the cause of the failures. It was as a result of these meetings that single event upset (SEU) was determined to be the root cause of the failures. The meeting participants also identified a list of actions to improve the reliability of DIS systems. As a result of the DIS meetings and the identified actions, the U.S. Support Program approved a request from the IAEA and established Task E.125, 'Remote Monitoring and Unattended Digital Surveillance Systems.' This task is an umbrella task intended to provide a mechanism for response to IAEA needs related to improving the reliability of unattended, remote monitoring and DIS equipment. Subtasks approved under this task include: E.125.1, 'SDIS Software Consolidation and DCM-14 Audit' - This subtask involves the consolidation of a number of individual upgrades to the SDIS and review of the DCM-14 software. As the sponsor of the design of the DCM-14 by Dr. Neumann, the German Support Program is also a participant in this subtask; E.125.2, 'DIS

  2. Equipment fragility testing

    International Nuclear Information System (INIS)

    Holman, G.S.; Chou, C.K.; Cummings, G.E.

    1985-01-01

    Current probabilistic risk assessment (PRA) methods for nuclear power plants utilize component fragilities which are for the most part based on a limited data base and engineering judgement. The seismic design of components is based on code limits and NRC requirements that do not reflect the actual capacity of a component to resist failure. In order to improve the present component fragility data base and establish component seismic design margins, the NRC has commissioned a projected three-year program to compile existing fragilities data and at the same time independently perform fragilities tests on selected mechanical and electrical components. This paper presents the planning and technical approach being taken by LLNL in the NRC Component Fragility Program

  3. Effect of a previous high hydrostatic pressure treatment on lipid damage in chilled Chilean jack mackerel (Trachurus murphyi

    Directory of Open Access Journals (Sweden)

    Maluenda, D.

    2013-12-01

    Full Text Available Lipid damage evolution was analyzed in chilled Chilean jack mackerel (Trachurus murphyi previously treated with high hydrostatic pressure (HHP technology. Different pressure levels and pressure holding times were tested. In addition, fish corresponding to pre- and post-rigor mortis (RM stages were comparatively studied. Previous HHP treatment led to a marked lipid hydrolysis inhibition in chilled fish. Increasing the pressure level and pressure holding time led to a lower free fatty acid content, with the effect of pressure being more relevant. According to the analysis of different types of lipid oxidation indexes, no effect of the previous HHP treatment on the lipid oxidation development could be determined in chilled jack mackerel. Concerning the effect of the RM stage of raw fish, a higher primary and secondary lipid oxidation development was observed in fish corresponding to the post-RM condition throughout the chilled storage; although a definite effect on lipid hydrolysis could not be found.Se estudió la evolución de la alteración lipídica en jurel chileno (Trachurus murphyi refrigerado previamente tratado a altas presiones hidrostáticas (HHP. Se aplicaron distintos valores de presión y tiempo de presurización; asimismo, se analizó de forma comparativa la respuesta al proceso del pescado inicial en estados pre- y post-rigor mortis (RM. El tratamiento previo por HHP produjo inhibición de la hidrólisis lipídica en pescado refrigerado, siendo más intenso el efecto de la presión que el del tiempo de presurización. De acuerdo con el análisis de distintos índices de oxidación, no se concluyó un efecto determinante sobre la oxidación lipídica por parte del tratamiento previo de HHP. En relación al efecto del estado de RM del pescado inicial, se observó una oxidación primaria y secundaria mayor en jurel correspondiente a la condición post-RM durante la conservación en refrigeración; sin embargo, no se detectó un efecto

  4. Development of manufacturing equipment and QC equipment for DUPIC fuel

    International Nuclear Information System (INIS)

    Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.

    1999-05-01

    In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs

  5. Guide to optimized replacement of equipment seals

    International Nuclear Information System (INIS)

    Gleason, J.F.

    1990-03-01

    A reevaluation of current scheduled replacement intervals of polymeric seals in plant equipment can achieve significant benefits. Information is provided which has the potential for increasing replacement intervals based on better information on how seals have performed through unique nuclear industry tests to qualify equipment, improved elastomers and increased knowledge of the failure mechanisms and related performance. The research was performed by reviewing applications of elastomeric seals in nuclear plants and practice associated with defining seal replacement intervals in the nuclear power and other industries. Performance indicators and how they predict degradation of seals were evaluated. Guidelines and a flow chart for reevaluating seal replacement intervals are provided. 29 refs., 38 figs., 8 tabs

  6. Maintenance or replacement of primary equipments

    International Nuclear Information System (INIS)

    Branchu, J.

    1995-01-01

    The principal materials, such as the primary equipments of a PWR type steam generator, have a finite service life. Framatome, builder of steam generators and maintenance contractor of Electricite de France has developed a methodology for the maintenance or the replacement of primary equipments. The paper describes the methodology followed by Framatome to identify and localize the wear mode and to treat or repair the component. Four failure modes have been considered: crack propagation, rubbing/vibration wear, neutron irradiation and corrosion propagation under permanent stress. A kinetic modelling of wear propagation has been computerized and validated using mechanical tests on Inconel 600 mockups. These analyses have allow to determine the strategy of repair or replacement of vessel heads for each unit. The method is evaluated taking into account the risk assessment, cost, dosimetry, efficiency and time delay involved. (J.S.). 1 fig., 3 photos

  7. Why does Jack, and not Jill, break his crown? Sex disparity in brain tumors.

    Science.gov (United States)

    Sun, Tao; Warrington, Nicole M; Rubin, Joshua B

    2012-01-25

    It is often reported that brain tumors occur more frequently in males, and that males suffer a worse outcome from brain tumors than females. If correct, these observations suggest that sex plays a fundamental role in brain tumor biology. The following review of the literature regarding primary and metastatic brain tumors, reveals that brain tumors do occur more frequently in males compared to females regardless of age, tumor histology, or region of the world. Sexually dimorphic mechanisms that might control tumor cell biology, as well as immune and brain microenvironmental responses to cancer, are explored as the basis for this sex disparity. Elucidating the mechanisms by which sex chromosomes and sex hormones impact on brain tumorigenesis and progression will advance our understanding of basic cancer biology and is likely to be essential for optimizing the care of brain tumor patients.

  8. Why does Jack, and not Jill, break his crown? Sex disparity in brain tumors

    Directory of Open Access Journals (Sweden)

    Sun Tao

    2012-01-01

    Full Text Available Abstract It is often reported that brain tumors occur more frequently in males, and that males suffer a worse outcome from brain tumors than females. If correct, these observations suggest that sex plays a fundamental role in brain tumor biology. The following review of the literature regarding primary and metastatic brain tumors, reveals that brain tumors do occur more frequently in males compared to females regardless of age, tumor histology, or region of the world. Sexually dimorphic mechanisms that might control tumor cell biology, as well as immune and brain microenvironmental responses to cancer, are explored as the basis for this sex disparity. Elucidating the mechanisms by which sex chromosomes and sex hormones impact on brain tumorigenesis and progression will advance our understanding of basic cancer biology and is likely to be essential for optimizing the care of brain tumor patients.

  9. Comparative toxic effects of some xenobiotics on the germination and early seedling growth of jack pine (Pinus banksiana Lamb. ) and white birch (Betula papyrifera Marsh. )

    Energy Technology Data Exchange (ETDEWEB)

    Weinberger, P; Vladut, R

    1981-12-01

    Seeds of jack pine (Pinus banksiana Lamb.) and white birch (Betula papyrifera Marsh.) were germinated in homogeneous emulsions or aqueous tank-mix solutions of fenitrothion or Matacil and their respective adjuvants: Atlox and Aerotex, or diluent oil No. 585 and nonylphenol. Percentage and peak germination values, water uptake, sprout length, ATP content, and morphological modifications were recorded from 0 to 14 or 21 days. Apart from 100 ppm fenitrothion which stimulated germination values, germination in jack pine was only marginally affected by any of the treatments; in contrast, white birch was negatively affected by all treatments. The most sensitive parameters of toxicity were the sprout length and ATP content after 14 days growth. Aberrant hypocotyl/root length ratios were evidenced in pine seeds after exposure to xenobiotic treatments which did not affect the germinative capacity of seeds. ATP content in the 14-day-old pine and birch seedlings was consistently higher than controls in all treatment sets. (Refs. 29).

  10. The web cast of the Nobel Prize of Physics of 2008, transmitted direct from Stockholm to the Globe of Science at CERN. Followed by a discussion among CERN theorists, with the participation of Jack Steinberger and John Ellis.

    CERN Multimedia

    Claudia Marcelloni

    2008-01-01

    The web cast of the Nobel Prize of Physics of 2008, transmitted direct from Stockholm to the Globe of Science at CERN. Followed by a discussion among CERN theorists, with the participation of Jack Steinberger and John Ellis.

  11. Chemical, laboratory analyses, physical and profile oceanographic data collected aboard the JACK FITZ in the Gulf of Mexico from 2010-08-18 to 2010-08-23 in response to the Deepwater Horizon Oil Spill event (NODC Accession 0069119)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Chemical, laboratory analyses, physical and profile oceanographic data were collected aboard the JACK FITZ in the Gulf of Mexico from 2010-08-18 to 2010-08-23 in...

  12. NRDA-processed CTD data from the JACK FITZ in the Gulf of Mexico, Cruise 3 Leg 1, collected from 2010-06-12 to 2010-06-20, associated with the Deepwater Horizon Oil Spill event (NCEI Accession 0128139)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Conductivity Temperature and Depth (CTD) measurements were collected aboard the R/V Jack Fitz, Cruise 03, to determine physical oceanographic parameters of the water...

  13. NRDA-processed CTD data from the JACK FITZ in the Gulf of Mexico, Cruise 2 Leg 1, collected from 2010-05-22 to 2010-05-31, associated with the Deepwater Horizon Oil Spill event (NCEI Accession 0128138)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Conductivity Temperature and Depth (CTD) measurements were collected aboard the R/V Jack Fitz, Cruise 02, to determine physical oceanographic parameters of the water...

  14. Chemical, laboratory analyses, physical and profile oceanographic data collected aboard the JACK FITZ in the Gulf of Mexico from 2010-06-12 to 2010-06-20 in response to the Deepwater Horizon Oil Spill event (NODC Accession 0069074)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Chemical, laboratory analyses, physical and profile oceanographic data were collected aboard the JACK FITZ in the Gulf of Mexico from 2010-06-12 to 2010-06-20 in...

  15. TRANSPORT AND EMPLACEMENT EQUIPMENT DESCRIPTIONS

    International Nuclear Information System (INIS)

    1997-01-01

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) Transport and Emplacement in the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. The Transport and Emplacement equipment described in this document consists of the following: (1) WP Transporter; (2) Reusable Rail Car; (3) Emplacement Gantry; (4) Gantry Carrier; and (5) Transport Locomotive

  16. Containment and Surveillance Equipment Compendium

    International Nuclear Information System (INIS)

    Luetters, F.O.

    1980-02-01

    The Containment and Surveillance Equipment Compendium contains information sections describing the application and status of seals, optical surveillance systems, and monitors for international safeguards systems. The Compendium is a collection of information on equipment in use (generally by the IAEA) or under development in the US in diverse programs being conducted at numerous facilities under different sponsors. The Compendium establishes a baseline for the status and applications of C/S equipment and is a tool to assist in the planning of future C/S hardware development activities. The Appendix contains design concepts which can be developed to meet future goals

  17. Anticonvulsive and free radical scavenging actions of two herbs, Uncaria rhynchophylla (MIQ) Jack and Gastrodia elata Bl., in kainic acid-treated rats.

    Science.gov (United States)

    Hsieh, C L; Tang, N Y; Chiang, S Y; Hsieh, C T; Lin, J G

    1999-01-01

    Uncaria rhynchophylla (Miq.) Jack (UR) and Gastrodia elata BI. (GE) are traditional Chinese herbs that are usually used in combination to treat convulsive disorders, such as epilepsy, in China. The aim of this study was to compare the anticonvulsive and free radical scavenging activities of UR alone and UR in combination with GE in rats. For the in vitro studies, brain tissues from 6 male Sprague-Dawley (SD) rats were treated with 120 microg/ml kainic acid (KA), with or without varied concentrations of UR or UR plus GE. For the in vivo studies, male SD rats (6 per group) received intraperitoneal (i.p.) injection of KA 12 mg/kg to induce epileptic seizures and generation of free radicals, with or without oral administration of UR 1 g/kg alone or UR 1 g/kg plus GE 1 g/kg. Epileptic seizures were verified by behavioral observations, and electroencephalography (EEG) and electromyography (EMG) recordings. These results showed that UR alone decreased KA-induced lipid peroxide levels in vitro, whereas UR plus GE did not produce a greater effect than UR alone. UR significantly reduced counts of wet dog shakes (WDS), paw tremor (PT) and facial myoclonia (FM) in KA-treated rats and significantly delayed the onset time of WDS, from 27 min in the control group to 40 min in the UR group. UR plus GE did not inhibit seizures more effectively than UR alone, but did further prolong the onset time of WDS to 63 min (P < 0.05 vs. UR alone). UR alone reduced the levels of free radicals in vivo, as measured by lipid peroxidation in the brain and luminol-chemiluminescence (CL) counts and lucigenin-CL counts in the peripheral whole blood, but the combination of GE and UR did not reduce free radical levels more markedly than UR alone. In conclusion, our results indicate that UR has anticonvulsive and free radical scavenging activities, and UR combined with GE exhibit greater inhibition on the onset time of WDS than UR alone. These findings suggest that the anticonvulsive effects of UR and

  18. Practices of prolongation of the I and C equipment lifetime

    International Nuclear Information System (INIS)

    Samoylov, O.B.; Pronin, V.S.; Savelov, I.D.; Bogomazov, V.A.; Drumov, V.V.; Chudin, A.G.

    2000-01-01

    The lifetime of nuclear power plants (NPP) always exceeds the operational time of Instrumentation and Control (I and C) systems. Ageing of I and C equipment in NPPs have many aspects. Research of these aspects is being performed in OKB Mechanical Engineering. Under condition of fast development of I and C systems and applying more stringent safety requirements, modernization of the equipment irrespective of its operational condition is getting important. However, an equipment of I and C systems operated in Russia was designed and manufactured applying highest requirements for a reliability of their work during its whole operational time. Therefore, in many cases it is not necessary to replace them in spite of expiration of their specified lifetime. During operation this equipment is maintained in a proper operation condition by a special service procedures stipulated by its development. When the equipment lifetime approaches to its end, lifetime extension for the certain period should be considered. (author)

  19. Proposal for the award of a contract for the supply of motor unit for the jacks for the LHC low-beta quadrupoles

    CERN Document Server

    2005-01-01

    This document concerns the award of a contract for the supply of 134 motor units for the jacks for the LHC low-beta quadrupoles. The Finance Committee is invited to agree to the negotiation of a contract with ZTS VVU KOSICE (SK), the lowest bidder, for the supply of 134 motor units for a total amount of 1 266 674 Swiss francs, not subject to revision.

  20. Effects of soil temperature and elevated atmospheric CO2 concentration on gas exchange, in vivo carboxylation and chlorophyll fluorescence in jack pine and white birch seedlings

    International Nuclear Information System (INIS)

    Zhang, S.; Dang, Q-L.

    2005-01-01

    The interactive effects of soil temperature and elevated carbon dioxide on the photosynthetic functions of white birch and jack pine were investigated. Elevated carbon dioxide was found to significantly decrease the allocation of electron transport to photorespiration in both species by increasing electron allocation to Rubisco carboxylation. Photosynthetic down-regulation occurred in both species after four months in elevated carbon dioxide as evidenced by decreases in maximal carboxylation rate which were unaffected by soil temperature. 50 refs., 5 figs

  1. Validation of a high performance liquid chromatography method for quantitation of L-proline in 20 % tincture from Murraya paniculata L. Jack

    International Nuclear Information System (INIS)

    Varona Torres, Noel; Gutierrez Gaiten, Yamilet Irene; Casado Martin, Celia Magaly

    2014-01-01

    The search for analytical methods that may monitor the quality of drugs is an issue of great interest in the pharmaceutical field, even more if they are directed to studying chemical markers of medicinal plants, their extracts and phytomedicines. To validate a high-resolution liquid chromatography (HPLC) method for the quantitative determination of the L-proline amino acid as a marker substance in Murraya paniculata L. Jack tincture

  2. Pervasive remagnetization of detrital zircon host rocks in the Jack Hills, Western Australia and implications for records of the early geodynamo

    Science.gov (United States)

    Weiss, Benjamin P.; Maloof, Adam C.; Tailby, Nicholas; Ramezani, Jahandar; Fu, Roger R.; Hanus, Veronica; Trail, Dustin; Bruce Watson, E.; Harrison, T. Mark; Bowring, Samuel A.; Kirschvink, Joseph L.; Swanson-Hysell, Nicholas L.; Coe, Robert S.

    2015-11-01

    It currently is unknown when Earth's dynamo magnetic field originated. Paleomagnetic studies indicate that a field with an intensity similar to that of the present day existed 3.5 billion years ago (Ga). Detrital zircon crystals found in the Jack Hills of Western Australia are some of the very few samples known to substantially predate this time. With crystallization ages ranging from 3.0-4.38 Ga, these zircons might preserve a record of the missing first billion years of Earth's magnetic field history. However, a key unknown is the age and origin of magnetization in the Jack Hills zircons. The identification of >3.9 Ga (i.e., Hadean) field records requires first establishing that the zircons have avoided remagnetization since being deposited in quartz-rich conglomerates at 2.65-3.05 Ga. To address this issue, we have conducted paleomagnetic conglomerate, baked contact, and fold tests in combination with U-Pb geochronology to establish the timing of the metamorphic and alteration events and the peak temperatures experienced by the zircon host rocks. These tests include the first conglomerate test directly on the Hadean-zircon bearing conglomerate at Erawandoo Hill. Although we observed little evidence for remagnetization by recent lightning strikes, we found that the Hadean zircon-bearing rocks and surrounding region have been pervasively remagnetized, with the final major overprinting likely due to thermal and/or aqueous effects from the emplacement of the Warakurna large igneous province at ∼1070 million years ago (Ma). Although localized regions of the Jack Hills might have escaped complete remagnetization, there currently is no robust evidence for pre-depositional (>3.0 Ga) magnetization in the Jack Hills detrital zircons.

  3. X-ray diffraction, XAFS and scanning electron microscopy study of otolith of a crevalle jack fish (caranx hippos)

    Energy Technology Data Exchange (ETDEWEB)

    Pattanaik, Sidhartha [Bailey Hall 703, Illinois Institute of Technology, 3101 S. Wabash Avenue, Chicago, IL 60616 (United States)]. E-mail: sidpattanaik@yahoo.com

    2005-04-01

    The otolith of a crevalle jack fish (caranx hippos) has been investigated by means of X-ray diffraction, X-ray absorption fine structure spectroscopy and scanning electron microscopy techniques. The results suggest that the biomineralization of otolith occurs predominantly in the aragonite phase. A detailed X-ray Rietveld analysis showed that the first shell Ca-O distances in otolith lay in the range 2.371-2.652 A, with each calcium atom coordinated to 9 oxygen atoms. While the average Ca-O distance remains same in both otolith and aragonite, certain Ca-O distances in otolith differ markedly from those in aragonite. Such difference reflects the remarkable degree of control that the protein matrix exercised over packing of calcium and carbonate ions to promote growth of rarer aragonite otolith. In view of the complex coordination chemistry of calcium in otoliths, the EXAFS analysis was limited to obtaining local atomic environment about calcium up to the first Ca-O shell. EXAFS data showed an asymmetric distribution of Ca-O bond distances with the centroid of distribution at 2.48 A, which is closer to the average Ca-O distance in aragonite than in calcite. The asymmetry in the Ca-O peak is consistent with an apparent departure of Ca-O distances from a near regular distribution, as expected of an aragonite otolith.

  4. X-ray diffraction, XAFS and scanning electron microscopy study of otolith of a crevalle jack fish (caranx hippos)

    International Nuclear Information System (INIS)

    Pattanaik, Sidhartha

    2005-01-01

    The otolith of a crevalle jack fish (caranx hippos) has been investigated by means of X-ray diffraction, X-ray absorption fine structure spectroscopy and scanning electron microscopy techniques. The results suggest that the biomineralization of otolith occurs predominantly in the aragonite phase. A detailed X-ray Rietveld analysis showed that the first shell Ca-O distances in otolith lay in the range 2.371-2.652 A, with each calcium atom coordinated to 9 oxygen atoms. While the average Ca-O distance remains same in both otolith and aragonite, certain Ca-O distances in otolith differ markedly from those in aragonite. Such difference reflects the remarkable degree of control that the protein matrix exercised over packing of calcium and carbonate ions to promote growth of rarer aragonite otolith. In view of the complex coordination chemistry of calcium in otoliths, the EXAFS analysis was limited to obtaining local atomic environment about calcium up to the first Ca-O shell. EXAFS data showed an asymmetric distribution of Ca-O bond distances with the centroid of distribution at 2.48 A, which is closer to the average Ca-O distance in aragonite than in calcite. The asymmetry in the Ca-O peak is consistent with an apparent departure of Ca-O distances from a near regular distribution, as expected of an aragonite otolith

  5. Conformational change results in loss of enzymatic activity of jack bean urease on its interaction with silver nanoparticle.

    Science.gov (United States)

    Ponnuvel, Shobana; Subramanian, Balakumar; Ponnuraj, Karthe

    2015-10-01

    Urease is an enzyme produced by microbes such as bacteria, yeast and fungi. Plants also produce this enzyme. Urease action splits urea into ammonia and carbamate. This action is having important implications in agro-chemical, medicinal and environment. Therefore there is always a constant search for new and novel compounds which could inhibit this enzyme. Here we have studied the interaction of jack bean urease (JBU) with silver nanoparticle to analyze the influence of the resultant protein corona formation on the catalytic property of JBU. Several techniques like UV-Vis, gel shift assay and CD spectroscopy have been used to characterize this interaction. Urease activity assay suggests that the protein corona formation inhibits the enzymatic action of JBU. The loss of enzymatic action could be either due to the nanoparticle blocking the active site of JBU or a conformational change in the protein. The CD spectra of JBU-AgNP complexes clearly revealed significant changes in the secondary structural composition of the JBU and this could be the reason for the loss of enzymatic activity of JBU. This study revealed an interesting observation, where the interaction of AgNP with JBU resulted destabilization of hexameric nature of JBU which is otherwise highly stable. The results of the present study could be useful in the development of nanoparticle based material for inhibiting the ureolytic activity of ureases in different fields.

  6. Tree rings provide early warning signals of jack pine mortality across a moisture gradient in the southern boreal forest

    Science.gov (United States)

    Mamet, S. D.; Chun, K. P.; Metsaranta, J. M.; Barr, A. G.; Johnstone, J. F.

    2015-08-01

    Recent declines in productivity and tree survival have been widely observed in boreal forests. We used early warning signals (EWS) in tree ring data to anticipate premature mortality in jack pine (Pinus banksiana)—an extensive and dominant species occurring across the moisture-limited southern boreal forest in North America. We sampled tree rings from 113 living and 84 dead trees in three soil moisture regimes (subxeric, submesic, subhygric) in central Saskatchewan, Canada. We reconstructed annual increments of tree basal area to investigate (1) whether we could detect EWS related to mortality of individual trees, and (2) how water availability and tree growth history may explain the mortality warning signs. EWS were evident as punctuated changes in growth patterns prior to transition to an alternative state of reduced growth before dying. This transition was likely triggered by a combination of severe drought and insect outbreak. Higher moisture availability associated with a soil moisture gradient did not appear to reduce tree sensitivity to stress-induced mortality. Our results suggest tree rings offer considerable potential for detecting critical transitions in tree growth, which are linked to premature mortality.

  7. Total flavonoid content and antioxidant activity in leaves and stems extract of cultivated and wild tabat barito (Ficus deltoidea Jack)

    Science.gov (United States)

    Manurung, Hetty; Kustiawan, Wawan; Kusuma, Irawan W.; Marjenah

    2017-02-01

    Tabat barito (Ficus deltoidea Jack) is a name given by Dayak Tribe who lived in Borneo-Kalimantan and it is belongs to the moraceae. Almost all of the parts of F. deltoidea plant is widely used as a medicinal property. The total flavonoid content (TFC) and antioxidant activity from cultivated and wild F. deltoidea leaves and stems extract were assessed. Total flavonoid content was estimated by using Aluminium chloride colorimetric method and expressed as catechin equivalents (mg CE g-1 extract) and the antioxidant activity by the DPPH (2,2-diphenyl-1-picryl hydrazyl) method. The content of total flavonoid of leaves and stems (430.77 and 371.80 µg CE mg-1 extract) of cultivated F. deltoidea were higher than in the wild leaves and stems (114.82 and 66.67 µg CE mg-1 extract). The IC50 of leaves extract of cultivated and wild F. deltoidea, based on the DPPH assay, has a strong antioxidant activity (34.19 and 39.31 µg mL-1 extract) as compared to stems extract. These results showed that the cultivated F. deltoidea are suitable source for medicinal properties and the leaves could be exploited as source of natural antioxidants.

  8. Comparison of Method for the Simultaneous Analysis of Bioactive for the Eurycoma longifolia jack using different Analysis Methods

    International Nuclear Information System (INIS)

    Salmah Moosa; Sobri Hussein; Rusli Ibrahim; Maizatul Akmam Md Nasir

    2011-01-01

    Eurycoma longifolia jack (Tongkat Ali, Genus: Eurycoma; Family, Simaroubaceae) is one of the most popular tropical herbal plants. The plant contains a series of quassinoids, which are mainly responsible for its bitter taste. The plant extract, especially roots, are exclusively used (traditionally) for enhancing testosterone levels in men. The roots also have been used in indigenous traditional medicines for its unique anti-malarial, anti-pyretic, antiulcer, cytotoxic and aphrodisiac properties. As part of an on-going research on the bioactive compound of Eurycoma longifolia and evaluation for an optimized analysis method and parameter that influence in LC-MS analysis were carried out. Identification of the bioactive compounds was based on comparison of calculated retention time and mass spectral data with literature values. Examination of the Eurycoma longifolia sample showed some variations and differences in terms of parameters in LC-MS. However, combined method using methanol as the solvent with injection volume 1.0 μL and analysis in ultra scan mode and acetic acid as acidic modifier is the optimum method for LCMS analysis of Eurycoma longifolia because it successfully detected the optimum mass of compounds with good resolution and perfectly separated within a short analysis time. (author)

  9. Soil respiration and photosynthetic uptake of carbon dioxide by ground-cover plants in four ages of jack pine forest

    Science.gov (United States)

    Striegl, Robert G.; Wickland, K.P.

    2001-01-01

    Soil carbon dioxide (CO2) emission (soil respiration), net CO2 exchange after photosynthetic uptake by ground-cover plants, and soil CO2 concentration versus depth below land surface were measured at four ages of jack pine (Pinus banksiana Lamb.) forest in central Saskatchewan. Soil respiration was smallest at a clear-cut site, largest in an 8-year-old stand, and decreased with stand age in 20-year-old and mature (60-75 years old) stands during May-September 1994 (12.1, 34.6, 31.5, and 24.9 mol C??m-2, respectively). Simulations of soil respiration at each stand based on continuously recorded soil temperature were within one standard deviation of measured flux for 48 of 52 measurement periods, but were 10%-30% less than linear interpolations of measured flux for the season. This was probably due to decreased soil respiration at night modeled by the temperature-flux relationships, but not documented by daytime chamber measurements. CO2 uptake by ground-cover plants ranged from 0 at the clear-cut site to 29, 25, and 9% of total growing season soil respiration at the 8-year, 20-year, and mature stands. CO2 concentrations were as great as 7150 ppmv in the upper 1 m of unsaturated zone and were proportional to measured soil respiration.

  10. White Anglo-Saxon hopes and black Americans' Atlantic dreams: Jack Johnson and the British boxing colour bar.

    Science.gov (United States)

    Runstedtler, Theresa

    2010-01-01

    This article examines the controversy surrounding Jack Johnson's proposed world heavyweight title fight against the British champion Bombardier Billy Wells in London (1911). In juxtaposing African Americans' often glowing discussions of European tolerance with the actual white resistance the black champion faced in Britain, including the Home Office's eventual prohibition of the match, the article explores the period's transnational discourses of race and citizenship. Indeed, as white sportsmen on both sides of the Atlantic joined together in their search for a "White Hope" to unseat Johnson, the boxing ring became an important cultural arena for interracial debates over the political and social divisions between white citizens and nonwhite subjects. Although African Americans had high hopes for their hero's European sojourn, the British backlash against the Johnson-Wells match underscored the fact that their local experiences of racial oppression were just one facet of a much broader global problem. At the same time, the proposed prizefight also made the specter of interracial conflict in the colonies all the more tangible in the British capital, provoking public discussions about the merits of U.S. racial segregation, along with the need for white Anglo-Saxon solidarity around the world. Thus, this article not only exposes the underlying connections between American Jim Crow and the racialized fault lines of British imperialism, but it also traces the "tense and tender ties" linking U.S. and African American history with the new imperial history and postcolonial studies.

  11. Data Center Equipment Location and Monitoring System

    DEFF Research Database (Denmark)

    2013-01-01

    Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to an equipment rack controller on the equipment rack. The equipment rack controllers link to a central control computer that provides an operator ...

  12. EAS Equipment Authorization Grantee Registrations

    Data.gov (United States)

    Federal Communications Commission — EAS (Equipment Authorization System). Radio Frequency (RF) devices are required to be properly authorized under 47 CFR Part 2 prior to being marketed or imported...

  13. ENERGY STAR Certified Imaging Equipment

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 2.0 ENERGY STAR Program Requirements for Imaging Equipment that are effective as of...

  14. EMR Measurements on NDA Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Macdonell, Alexander Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meierbachtol, Krista Cruse [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Evans, James Walter Jr. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mayo, Douglas R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-07-10

    Electromagnetic radiation (EMR) emission strength measurements were performed on a suite of passive non-destructive assay (NDA) radiation detection equipment. Data were collected from 9 kHz up to 6 GHz on each of the assembled systems.

  15. Mongolia - Vocational Education - Equipment Upgrades

    Data.gov (United States)

    Millennium Challenge Corporation — Evaluation design The impact evaluation sought to identify the causal impact of exposure to equipment upgrades on subsequent outcomes. Insofar as we were not able to...

  16. Origins of eponymous orthopaedic equipment.

    Science.gov (United States)

    Meals, Clifton; Wang, Jeffrey

    2010-06-01

    Orthopaedists make great use of eponymous equipment, however the origins of these tools are unknown to many users. This history enriches, enlightens, and enhances surgical education, and may inspire modern innovation. We explored the origins of common and eponymous orthopaedic equipment. We selected pieces of equipment named for their inventors and in the broadest use by modern orthopaedists. We do not describe specialized orthopaedic implants and instruments owing to the overwhelming number of these devices. The history of this equipment reflects the coevolution of orthopaedics and battlefield medicine. Additionally, these stories evidence the primacy of elegant design and suggest that innovation is often a process of revision and refinement rather than sudden inspiration. Their history exposes surgical innovators as brilliant, lucky, hardworking, and sometimes odd. These stories amuse, enlighten, and may inspire modern orthopaedists to develop creative solutions of their own. The rich history of the field's eponymous instruments informs an ongoing tradition of innovation in orthopaedics.

  17. Operation monitor for plant equipment

    International Nuclear Information System (INIS)

    Kondo, Tetsufumi; Kanemoto, Shigeru.

    1991-01-01

    In a nuclear power plant, states of each of equipment in the plant are monitored accurately even under such a operation condition that the power is changed. That is, the fundamental idea is based on a model comparison method. A deviation between an output signal upon normal plant state obtained in a forecasting model device and that of the objective equipment in the plant are compared with a predetermined value. The result of the comparison is inputted to an alarm device to alarm the abnormality of the states of the equipment to an operator. The device of the present invention thus constituted can monitor the abnormality of the operation of equipment accurately even under such a condition that a power level fluctuates. As a result, it can remarkably contribute to mitigate operator's monitoring operation under the condition such as during load following operation. (I.S.)

  18. Equipment improvements for performance enhancement

    International Nuclear Information System (INIS)

    Gaestel, P.; Guesnon, H.; Sauze, G.

    1994-01-01

    In order to enhance the reactor availability, several improvements on reactor equipment have been developed: design optimization for stator maintenance replacement in the main alternator; adjustment modification of stator coils in the main alternator for an easier maintenance; improvement of the fuel handling line (pole crane, transfer equipment, loading machine); development of a loose part trapping system in the steam generator secondary circuit. 1 tab

  19. Low level photoneutron detection equipment

    International Nuclear Information System (INIS)

    Ji Changsong; Zhang Yuqin; Li Yuansui

    1991-01-01

    A low level photoneutron detection equipment has been developed. The photoneutrons produced by interaction of 226 Ra gamma quanta and deutron (D) target are detected with n-n discrimination detector made up of 3 He proportional counter array. The D-content information in the target can be obtained from the measured photoneutron counts. The equipment developed is mainly used for nondestructive D-content measurement of D-devices

  20. FUSRAP equipment concept development study

    International Nuclear Information System (INIS)

    Hinerman, K.B.; Smith, R.E.

    1981-01-01

    Under DOE contract, Dalton-Dalton-Newport, Inc. is performing an engineering evaluation of three selected FUSRAP sites in an effort to generate equipment concepts to perform remedial action for retrieval, packaging, storing, and transporting contaminated soil and other debris. Along with this engineering evaluation, an analysis of state and Federal regulations was made which had significant impact on the selected equipment and costs for each remedial action concept

  1. Remotely operated replaceable process equipment

    International Nuclear Information System (INIS)

    Westendorf, H.

    1987-01-01

    The coupling process of pneumatic and electrical auxiliary lines of a pneumatic control pressure line in a large cell of the reprocessing plant is carried out, together with the coupling process of the connecting flange of the process equipment. The coupling places of the auxiliary lines, such as control or supply lines, are laid in the flange parts of the flanges to be connected. The pipe flange on the frame side remains flush with the connecting flange of the process equipment. (DG) [de

  2. Partners in qualified equipment supply

    International Nuclear Information System (INIS)

    Rygg, D.E.; O'Hare, G.J.

    1993-01-01

    Industry initiatives have been taken to improve procurement practices and commercial dedication programs, formation of procurement engineering groups, emphasis on product quality, and increased engineering involvement in procurement and maintenance of qualified equipment. This poses new challenges for many licensees in terms of resources, product knowledge, and access to information normally held proprietary by equipment suppliers. Alternative approaches to future licensee/Westinghouse relationships which will allow licensees to adapt to the changing environment are discussed. 2 figs

  3. Damage caused to houses and equipment by underground nuclear explosions

    International Nuclear Information System (INIS)

    Delort, F.; Guerrini, C.

    1969-01-01

    A description is given of the damaged caused to various structures, buildings, houses, mechanical equipment and electrical equipment by underground nuclear explosions in granite. For each type of equipment or building are given the limiting distances for a given degree of damage. These distances have been related to a parameter characterizing the movement of the medium; it is thus possible to generalize the results obtained in granite, for different media. The problem of estimating the damage caused at a greater distance from the explosion is considered. (authors) [fr

  4. Equipment for inspection of austenitic stainless steel pipe welds

    International Nuclear Information System (INIS)

    Boehmer, W.D.; Horn, J.E.

    1979-01-01

    A computer controlled ultrasonic scanning system and a data acquisition and analysis system have been developed to perform the inservice inspection of welds in stainless steel sodium piping in the Fast Flux Test Facility. The scanning equipment consists of a six axis motion mechanism and control system which allows full articulation of an ultrasonic transducer as it follows the circumferential pipe welds. The data acquisition and analysis system consists of high speed ultrasonic waveform digitizing equipment, dedicated processors to perform on-line analysis, and data storage and display equipment

  5. Detrital Zircons From the Jack Hills and Mount Narryer, Western Australia: Geochronological, Morphological, and Geochemical Evidence for Diverse >4000 Ma Source Rocks

    Science.gov (United States)

    Crowley, J. L.; Myers, J. S.; Sylvester, P. J.; Cox, R. A.

    2004-05-01

    Detrital zircons from all major clastic units in the Jack Hills and Mount Narryer metasedimentary belts, Western Australia, were analyzed for morphology, internal zoning, inclusion mineralogy, age, and trace element concentrations (latter two obtained by laser-ablation microprobe ICPMS). The results show that zircons were derived from a wide diversity of rocks, including previously described, >4000 Ma grains that are older than any known terrestrial rocks. In three metaconglomerate samples from the western Jack Hills, 4200-3800 Ma zircons ("old grains") comprise 14% of the population, 3800-3600 Ma grains form only 2%, and 3550-3250 Ma zircons ("young grains") are dominant with a significant peak at 3380 Ma. Old and young grains are interpreted as being from similar rock types because they are indistinguishable in trace element concentrations, size (several hundred microns), morphology (subequant, typically fragmented), internal zoning (typically both oscillatory and sector), and U concentration (50-200 ppm). Many of these properties suggest an intermediate plutonic source, whereas an evolved granitic source was previously interpreted from rare-earth element and oxygen isotope data. Detrital zircons in quartzites and metaconglomerates at Mount Narryer differ significantly from zircons from the western Jack Hills. Old grains comprise only 3% (most of which are 4200-4100 Ma), 3800-3600 Ma zircons form 31%, and there are peaks at 3650, 3600, and 3500 Ma. Old and young grains have similar properties that suggest granitic sources, such as elongate prismatic morphology, oscillatory zoning, high U concentrations (100-600 ppm), and xenotime and monazite inclusions. Trace element concentrations are broadly similar to those in Jack Hills zircons, with notable exceptions being generally higher U, smaller Ce and Eu anomalies, and lower Nb/Ta. It is considered unlikely that Jack Hills zircons were derived from granitic gneisses that surround the metasedimentary belts because

  6. 29 CFR 97.32 - Equipment.

    Science.gov (United States)

    2010-07-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  7. 44 CFR 13.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  8. 24 CFR 85.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  9. 41 CFR 105-71.132 - Equipment.

    Science.gov (United States)

    2010-07-01

    .... (4) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be... managing equipment (including replacement equipment), whether acquired in whole or in part with grant funds... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Equipment. 105-71.132...

  10. 43 CFR 12.72 - Equipment.

    Science.gov (United States)

    2010-10-01

    ...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...

  11. 1968 Listing of Swimming Pool Equipment.

    Science.gov (United States)

    National Sanitation Foundation, Ann Arbor, MI. Testing Lab.

    An up-to-date listing of swimming pool equipment including--(1) companies authorized to display the National Sanitation Foundation seal of approval, (2) equipment listed as meeting NSF swimming pool equipment standards relating to diatomite type filters, (3) equipment listed as meeting NSF swimming pool equipment standard relating to sand type…

  12. Process insulation. Isolation thermique des equipements

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    A manual is presented to assist managers and operating personnel to recognize industrial energy management opportunities, and provides mathematical equations, general information on proven techniques and technology, and examples. It deals with process insulation, focusing on the insulation of mechanical systems such as piping, process vessels, equipment, and ductwork. The manual describes the effects of insulation materials; commonly encountered types of insulation, coverings and protective finishes as well as common applications; energy management opportunities, divided into housekeeping, low cost, and retrofit; and includes worked examples of each. Includes glossary. 17 figs., 8 tabs.

  13. Activity of the Service for maintenance of mechanical equipment of the RA reactor - Report, Annex II; Prilog II - Rad sluzbe za odrzavanje masinske opreme reaktora RA u 1979. godini - Izvestaj -

    Energy Technology Data Exchange (ETDEWEB)

    Radivojevic, J [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1979-12-15

    Service for mechanical components at the RA reactor includes: control and maintenance of utility components, mechanical workshop, hot cells and storage. Control and maintenance of main components covers: reactor core, heavy water system, technical water system, gas system. This service is responsible for the following auxiliary systems: transportation units; spent fuel storage pool; special ventilation system; personal protection appliances; hot cells. Maintenance of the reactor building, ventilation, heating, water supply, sewage, fire protection devices, gas and compressed air systems are included. [Serbo-Croat] Sluzba za masinsku opremu nuklearnog reaktora RA obuhvata: kontrolu i odrzavanje masinske opreme postrojenja, masinsku radionicu, vruce komore i prirucni magacin. Kontrola i odrzavanje osnovnih sistema obuhvata centralno telo reaktora, sistem teske vode, sistem tehnicke vode, gasni sistem. Pomocni sistemi koji spadaju u delatnost ove sluzbe su: transportna oprema, bazen za odlezavanje ozracenog goriva, sistem specijalne ventilacije, licna zastitna sredstva, vruce komore. Odrzavanje zgrade reaktora, ventilacije i grejanja, vodovoda i kanalizacije, opreme za protivpozarnu zastitu, instalacije gasa i komprimovanog vazduha su takode zadatak ove Sluzbe.

  14. Increased Air Temperature during Simulated Autumn Conditions Does Not Increase Photosynthetic Carbon Gain But Affects the Dissipation of Excess Energy in Seedlings of the Evergreen Conifer Jack Pine1[OA

    Science.gov (United States)

    Busch, Florian; Hüner, Norman P.A.; Ensminger, Ingo

    2007-01-01

    Temperature and daylength act as environmental signals that determine the length of the growing season in boreal evergreen conifers. Climate change might affect the seasonal development of these trees, as they will experience naturally decreasing daylength during autumn, while at the same time warmer air temperature will maintain photosynthesis and respiration. We characterized the down-regulation of photosynthetic gas exchange and the mechanisms involved in the dissipation of energy in Jack pine (Pinus banksiana) in controlled environments during a simulated summer-autumn transition under natural conditions and conditions with altered air temperature and photoperiod. Using a factorial design, we dissected the effects of daylength and temperature. Control plants were grown at either warm summer conditions with 16-h photoperiod and 22°C or conditions representing a cool autumn with 8 h/7°C. To assess the impact of photoperiod and temperature on photosynthesis and energy dissipation, plants were also grown under either cold summer (16-h photoperiod/7°C) or warm autumn conditions (8-h photoperiod/22°C). Photosynthetic gas exchange was affected by both daylength and temperature. Assimilation and respiration rates under warm autumn conditions were only about one-half of the summer values but were similar to values obtained for cold summer and natural autumn treatments. In contrast, photosynthetic efficiency was largely determined by temperature but not by daylength. Plants of different treatments followed different strategies for dissipating excess energy. Whereas in the warm summer treatment safe dissipation of excess energy was facilitated via zeaxanthin, in all other treatments dissipation of excess energy was facilitated predominantly via increased aggregation of the light-harvesting complex of photosystem II. These differences were accompanied by a lower deepoxidation state and larger amounts of β-carotene in the warm autumn treatment as well as by changes in

  15. Jacks of metal(loid chelation trade in plants – an overview

    Directory of Open Access Journals (Sweden)

    Naser A. Anjum

    2015-04-01

    Full Text Available Varied environmental compartments including soils are being contaminated by a myriad toxic metal(loids (hereafter termed as ‘metal/s’ mainly through anthropogenic activities. These metals may contaminate food chain and bring irreparable consequences in human. Plant-based approach (phytoremediation stands second to none among bioremediation technologies meant for sustainable cleanup of soils/sites with metal-contamination. In turn, the capacity of plants to tolerate potential consequences caused by the extracted/accumulated metals decides the effectiveness and success of phytoremediation system. Chelation is among the potential mechanisms that largely govern metal-tolerance in plant cells by maintaining low concentrations of free metals in cytoplasm. Metal-chelation can be performed by compounds of glutathione (GSH (reduced GSH; phytochelatins, PCs; metallothioneins, MTs and non-GSH (histidine, nicotianamine, organic acids origin. This paper presents an appraisal of recent reports on both GSH and non-GSH associated compounds in an effort to shed light on the significance of these compounds in metal-plant tolerance, as well as to provide scientific clues for the development of phytoextraction strategies.

  16. Performance monitoring of safeguards equipment

    International Nuclear Information System (INIS)

    Sirisena, K.; Peltoranta, M.; Goussarov, V.; Vodrazka, P.

    1999-01-01

    SGTCS is responsible for monitoring and reporting the performance of the SG equipment. Performance monitoring (PM) has been implemented in most important safeguards equipment operating unattended in nuclear facilities. Inspectors acquire equipment performance data in facilities. After inspection, the data package is submitted to SGTCS for processing and analysis. The performance data is used for identification of systems or components, which should be changed in the field and for identification of modules which, should be diagnosed at HQ in order to determine the cause of failure. Moreover, the performance data is used for preventive maintenance and spares distribution planning, and to provide statistics for official reports and management decision making. An important part of the performance monitoring is reporting. Equipment performance reports contain information about equipment inventory, utilization, failure types, failure distribution, and reliability. Trends in performance are given in graphical form in cases, where past data is available. Reliability estimates such as expected times between failures are provided. The automated reporting tools are obtainable through EMIS database application. (author)

  17. 78 FR 25916 - Authorization of Radiofrequency Equipment

    Science.gov (United States)

    2013-05-03

    ...] Authorization of Radiofrequency Equipment AGENCY: Federal Communications Commission. ACTION: Proposed rule... bodies, and measurement procedures used to determine RF equipment compliance. The Commission believes... Commission is responsible for an equipment authorization program for radiofrequency (RF) devices under part 2...

  18. Composition and Antibacterial Activity of the Essential Oils of Orthosiphon stamineus Benth and Ficus deltoidea Jack against Pathogenic Oral Bacteria

    Directory of Open Access Journals (Sweden)

    Nuramirah Azizan

    2017-12-01

    Full Text Available In this study, the essential oils of Orthosiphon stamineus Benth and Ficus deltoidea Jack were evaluated for their antibacterial activity against invasive oral pathogens, namely Enterococcus faecalis, Streptococcus mutans, Streptococcus mitis, Streptococcus salivarius, Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis and Fusobacterium nucleatum. Chemical composition of the oils was analyzed using gas chromatography (GC and gas chromatography-mass spectrometry (GC-MS. The antibacterial activity of the oils and their major constituents were investigated using the broth microdilution method (minimal inhibitory concentration (MIC and minimal bactericidal concentration (MBC. Susceptibility test, anti-adhesion, anti-biofilm, checkerboard and time-kill assays were also carried out. Physiological changes of the bacterial cells after exposure to the oils were observed under the field emission scanning electron microscope (FESEM. O. stamineus and F. deltoidea oils mainly consisted of sesquiterpenoids (44.6% and 60.9%, respectively, and β-caryophyllene was the most abundant compound in both oils (26.3% and 36.3%, respectively. Other compounds present in O. stamineus were α-humulene (5.1% and eugenol (8.1%, while α-humulene (5.5% and germacrene D (7.7% were dominant in F. deltoidea. The oils of both plants showed moderate to strong inhibition against all tested bacteria with MIC and MBC values ranging 0.63–2.5 mg/mL. However, none showed any inhibition on monospecies biofilms. The time-kill assay showed that combination of both oils with amoxicillin at concentrations of 1× and 2× MIC values demonstrated additive antibacterial effect. The FESEM study showed that both oils produced significant alterations on the cells of Gram-negative bacteria as they became pleomorphic and lysed. In conclusion, the study indicated that the oils of O. stamineus and F. deltoidea possessed moderate to strong antibacterial properties against the seven

  19. Composition and Antibacterial Activity of the Essential Oils of Orthosiphon stamineus Benth and Ficus deltoidea Jack against Pathogenic Oral Bacteria.

    Science.gov (United States)

    Azizan, Nuramirah; Mohd Said, Shahida; Zainal Abidin, Zamirah; Jantan, Ibrahim

    2017-12-05

    In this study, the essential oils of Orthosiphon stamineus Benth and Ficus deltoidea Jack were evaluated for their antibacterial activity against invasive oral pathogens, namely Enterococcus faecalis , Streptococcus mutans , Streptococcus mitis , Streptococcus salivarius , Aggregatibacter actinomycetemcomitans , Porphyromonas gingivalis and Fusobacterium nucleatum . Chemical composition of the oils was analyzed using gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). The antibacterial activity of the oils and their major constituents were investigated using the broth microdilution method (minimal inhibitory concentration (MIC) and minimal bactericidal concentration (MBC)). Susceptibility test, anti-adhesion, anti-biofilm, checkerboard and time-kill assays were also carried out. Physiological changes of the bacterial cells after exposure to the oils were observed under the field emission scanning electron microscope (FESEM). O. stamineus and F. deltoidea oils mainly consisted of sesquiterpenoids (44.6% and 60.9%, respectively), and β-caryophyllene was the most abundant compound in both oils (26.3% and 36.3%, respectively). Other compounds present in O. stamineus were α-humulene (5.1%) and eugenol (8.1%), while α-humulene (5.5%) and germacrene D (7.7%) were dominant in F. deltoidea . The oils of both plants showed moderate to strong inhibition against all tested bacteria with MIC and MBC values ranging 0.63-2.5 mg/mL. However, none showed any inhibition on monospecies biofilms. The time-kill assay showed that combination of both oils with amoxicillin at concentrations of 1× and 2× MIC values demonstrated additive antibacterial effect. The FESEM study showed that both oils produced significant alterations on the cells of Gram-negative bacteria as they became pleomorphic and lysed. In conclusion, the study indicated that the oils of O. stamineus and F. deltoidea possessed moderate to strong antibacterial properties against the seven strains

  20. Engineering task plan for upgrades to the leveling jacks on core sample trucks number 3 and 4; TOPICAL

    International Nuclear Information System (INIS)

    KOSTELNIK, A.J.

    1999-01-01

    Characterizing the waste in underground storage tanks at the Hanford Site is accomplished by obtaining a representative core sample for analysis. Core sampling is one of the numerous techniques that have been developed for use given the environmental and field conditions at the Hanford Site. Core sampling is currently accomplished using either Push Mode Core Sample Truck No.1 or; Rotary Mode Core Sample Trucks No.2, 3 or 4. Past analysis (WHC 1994) has indicated that the Core Sample Truck (CST) leveling jacks are structurally inadequate when lateral loads are applied. WHC 1994 identifies many areas where failure could occur. All these failures are based on exceeding the allowable stresses listed in the American Institute of Steel Construction (AISC) code. The mode of failure is for the outrigger attachments to the truck frame to fail resulting in dropping of the CST and possible overturning (Ref. Ziada and Hundal, 1996). Out of level deployment of the truck can exceed the code allowable stresses in the structure. Calculations have been performed to establish limits for maintaining the truck level when lifting. The calculations and the associated limits are included in appendix A. The need for future operations of the CSTS is limited. Sampling is expected to be complete in FY-2001. Since there is limited time at risk for continued use of the CSTS with the leveling controls without correcting the structural problems, there are several design changes that could give incremental improvements to the operational safety of the CSTS with limited impact on available operating time. The improvements focus on making the truck easier to control during lifting and leveling. Not all of the tasks identified in this ETP need to be performed. Each task alone can improve the safety. This engineering task plan is the management plan document for implementing the necessary additional structural analysis. Any additional changes to meet requirements of standing orders shall require a

  1. Influences of vegetation structure and elevation on CO2 uptake in a mature jack pine forest in Saskatchewan, Canada

    International Nuclear Information System (INIS)

    Chasmer, L.; McCaughey, H.; Treitz, P.

    2008-01-01

    Eddy covariance (EC) is often used to measure the movement and direction of energy and trace gas concentrations in ecosystems. Data from EC networks are often combined with remote sensing data and ecosystem models in order to assess the spatial and temporal variability of carbon dioxide (CO 2 ) exchanges within specific areas of interest. This study presented a new method of determining changes in the structural characteristics of biomass and elevation. Lidar was used within the contours of half-hourly flux footprint areas to characterize vegetation structure and elevation. The influences of vegetation structure and elevation on CO 2 concentrations were measured by EC and Lidar measurements for 3 mature growing periods at a mature jack pine site in Saskatchewan. Mensuration data were collected over 2 periods. Meteorological, CO 2 , and H2O flux measurements were collected for 30 minute periods each day. Statistical analyses were conducted to determine the influence of meteorological variables on vegetation structure. Footprint contour lines were then layered onto the canopy height models derived by the lidar data. Multiple regression equations were used to determine net ecosystem productivity (NEP) and gross ecosystem productivity (GEP) using meteorological variables, canopy fractional cover; and elevation, as well as the results obtained from a Landsberg equation. The study showed that differences in NEP variability were influenced by differences in canopy and ground surface characteristics within the site. EC measurements underestimated gross CO 2 fluxes by 5 per cent as the biomass was lower within the immediate vicinity of the EC network. It was concluded that canopy structures and elevation are important factors for determining annual carbon balances. 36 refs., 8 tabs., 9 figs

  2. Another donation of computer equipment

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On Thursday 27 February, CERN was pleased to donate computer equipment to a physics institute in the Philippines.   H.E. Leslie J. Baja and Rolf Heuer. Following donations of computer equipment to institutes in Morocco, Ghana, Bulgaria, Serbia and Egypt, CERN is to send 50 servers and 4 network switches to the National Institute of Physics at the University of the Philippines Diliman. CERN’s Director-General Rolf Heuer and the Ambassador of the Philippines to Switzerland and Lichtenstein, H.E. Leslie J. Baja, spoke of their enthusiasm for the project during an official ceremony. The equipment will be used for various high energy physics research programmes in the Philippines and for the University’s development of digital resources for science.

  3. Anticonvulsant effect of Uncaria rhynchophylla (Miq) Jack. in rats with kainic acid-induced epileptic seizure.

    Science.gov (United States)

    Hsieh, C L; Chen, M F; Li, T C; Li, S C; Tang, N Y; Hsieh, C T; Pon, C Z; Lin, J G

    1999-01-01

    This study investigated the anticonvulsant effect of Uncaria rhynchophylla (UR) and the physiological mechanisms of its action in rats. A total of 70 male Sprague-Dawley (SD) rats were selected for study. Thirty four of these rats were divided into 5 groups as follows: 1) CONTROL GROUP (n = 6): received intraperitoneal injection (i.p.) of kainic acid (KA, 12 mg/kg); 2) UR1000 group (n = 10), 3) UR500 group (n = 6) 4) UR250 group, received UR 1000, 500, 250 mg/kg i.p. 30 min prior to KA administration, respectively; 5) Contrast group: received carbamazepine 20 mg/kg i.p. 30 min prior to KA administration. Behavior and EEG were monitored from 15 min prior to drug administration to 3 hours after KA administration. The number of wet dog shakes were counted at 10 min intervals throughout the experimental course. The remaining 36 rats were used to measure the lipid peroxide level in the cerebral cortex one hour after KA administration. These rats were divided into 6 groups of 6 rats as follows: 1) Normal group: no treatment was given; 2) CONTROL GROUP: received KA (12 mg/kg) i.p.; 3) UR1000 group, 4) UR500 group, 5) UR250 group, received UR 1000, 500, 250 mg/kg i.p. 30 min prior to KA administration, respectively; 6) Contrast group: received carbamazepine 20 mg/kg i.p. 30 min prior to KA administration. Our results indicated that both UR 1000 and 500 mg/kg decreased the incidence of KA-induced wet dog shakes, no similar effect was observed in the UR 250 mg/kg and carbamazepine 20 mg/kg group. Treatment with UR 1000 mg/kg, 500 mg/kg, or 250 mg/kg and carbamazepine 20 mg/kg decreased KA-induced lipid peroxide level in the cerebral cortex and was dose-dependent. These findings suggest that the anticonvulsant effect of UR possibly results from its suppressive effect on lipid peroxidation in the brain.

  4. Waste Electrical and Electronic Equipment

    DEFF Research Database (Denmark)

    Bigum, Marianne Kristine Kjærgaard; Christensen, Thomas Højlund

    2011-01-01

    Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans and the env......Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans...

  5. The development of superconducting equipment

    CERN Document Server

    Ueda, T; Hiue, H

    2003-01-01

    Fuji Electric has been developing various types of superconducting equipment for over a quarter of a century. This paper describes the development results achieved for superconducting equipment and especially focuses on large-capacity current leads and superconducting transmission systems, the development of which is being promoted for application to the field of nuclear fusion. High temperature superconductor (HTS) is becoming the mainstream in the field of superconductivity, and the HTS floating coil and conduction-cooled HTS transformed are also introduced as recent developments for devices that utilize this technology. (author)

  6. Damage Mechanism of High Voltage Solar Arrays and Electronic Equipment in the Plasma Environment%高压太阳能电池阵与电子设备在等离子体环境中的毁伤机理

    Institute of Scientific and Technical Information of China (English)

    施维; 郑步生; 刘少斌

    2015-01-01

    目的 通过研究高压太阳能电池阵与电子设备在等离子体环境中气体放电的毁伤机理,从而可运用于军事上的电子对抗、干扰及隐身技术.方法 通过分析气体放电的几种基本形式,研究太阳能电池阵和电子设备在等离子体射流或等离子体环境下可能发生的放电过程.结果 高压太阳能电池阵在等离子体环境下易产生电弧放电现象,而电子设备在此环境下的毁伤主要是通过内部充电与外部充电产生的.结论 在等离子体环境中,气体放电会对高压太阳能电池阵和电子设备产生严重的影响,可以利用这种影响对空间邻域的探索提供帮助.%Objective To research the damage mechanism of gas discharge of high voltage solar arrays and electronic equipment in the plasma environment in order to apply in electronic warfare, interference and military stealth technology. Methods By analysis of several basic forms of gas discharge, the discharge process of high voltage solar arrays and electronic equipment which may occur in the plasma jet or the plasma environment was researched. Results High voltage solar arrays were likely to generate arc discharge, and the damage of the electronic equipment was mainly caused by internal and external charging in this environment. Conclusion Gas discharge may have a serious effect on high voltage solar arrays and electronic equipment in the plasma environment. This effect may help to explore the spatial neighborhood.

  7. Finite-element analysis of some pneumatically-actuated wrist-rehabilitation equipment

    Directory of Open Access Journals (Sweden)

    Filip Ovidiu

    2017-01-01

    Full Text Available The paper presents some wrist-rehabilitation equipment, actuated by a pneumatic muscle. This one drives, through a rack-pinion mechanism, a Fin Ray-type mechanism, with a view to mobilizing the injured palm. Unlike other rehabilitation equipments, the one presented in this paper, ensures the movement of both palm and fingers.

  8. Development of equipment for fabricating DUPIC fuel powder

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Ho; Yang, M. S.; Park, J. J.; Lee, J. W.; Kim, J. H.; Cho, K. H.; Lee, D. Y.; Lee, Y. S.; Na, S. H

    1999-06-01

    The powder fabrication processes, as the first stage of manufacturing DUPIC (Direct Use of PWR spent fuel In CANDU) fuel, consist of the slitting of spent PWR fuel rods, REOX (Oxidation and REduction of Oxide Fuels) processing to produce the powder feedstock, the milling of the produced powder, the granulation of the milled powder, and the mixing of the granulated powder with pressing lubricants. All these processes should be conducted by remote means in a hot-cell environment where the direct human access is limited to the strictest minimum due to the high radioactivity. This report describe the development of the equipment for fabricating DUPIC fuel powder. These equipment are Slitting Machine, Oxidation and Reduction (OREOX) Furnace, Mill, Roll Compactor, and Mixer. Remote design concept was applied to all the equipment for use in the M6 hot-cell of the IMEF. Mechanical design considerations and capabilities of the equipment for remote operation and maintenance are presented. First prototypes were developed and installed in the DUPIC full scale mock-up and tested using a master-slave manipulator. Redesign and reconstruction were made on each equipment based on mock-up test results. The remote technology acquired through this research was utilized in developing other equipment for DUPIC fuel fabrication, thereby improving safety and increasing productivity. This technology could also be extended to the area of remote handling equipment development for use in hazardous environments. (author). 14 refs., 9 tabs., 21 figs.

  9. Development of equipment for fabricating DUPIC fuel powder

    International Nuclear Information System (INIS)

    Kim, Ki Ho; Yang, M. S.; Park, J. J.; Lee, J. W.; Kim, J. H.; Cho, K. H.; Lee, D. Y.; Lee, Y. S.; Na, S. H.

    1999-06-01

    The powder fabrication processes, as the first stage of manufacturing DUPIC (Direct Use of PWR spent fuel In CANDU) fuel, consist of the slitting of spent PWR fuel rods, REOX (Oxidation and REduction of Oxide Fuels) processing to produce the powder feedstock, the milling of the produced powder, the granulation of the milled powder, and the mixing of the granulated powder with pressing lubricants. All these processes should be conducted by remote means in a hot-cell environment where the direct human access is limited to the strictest minimum due to the high radioactivity. This report describe the development of the equipment for fabricating DUPIC fuel powder. These equipment are Slitting Machine, Oxidation and Reduction (OREOX) Furnace, Mill, Roll Compactor, and Mixer. Remote design concept was applied to all the equipment for use in the M6 hot-cell of the IMEF. Mechanical design considerations and capabilities of the equipment for remote operation and maintenance are presented. First prototypes were developed and installed in the DUPIC full scale mock-up and tested using a master-slave manipulator. Redesign and reconstruction were made on each equipment based on mock-up test results. The remote technology acquired through this research was utilized in developing other equipment for DUPIC fuel fabrication, thereby improving safety and increasing productivity. This technology could also be extended to the area of remote handling equipment development for use in hazardous environments. (author). 14 refs., 9 tabs., 21 figs

  10. Damage limits of accelerator equipment

    CERN Document Server

    Rosell, Gemma

    2014-01-01

    Beam losses occur in particle accelerators for various reasons. The effect of lost particles on accelerator equipment becomes more severe with the increasing energies and intensities. The present study is focused on the damage potential of the proton beam as a function of particle energy and beam size. Injection and extraction energies of different accelerators at CERN were considered.

  11. Pocket dictionary of laboratory equipment

    International Nuclear Information System (INIS)

    Junge, H.D.

    1987-01-01

    This pocket dictionary contains the 2500 most common terms for scientific and technical equipment in chemical laboratories. It is a useful tool for those who are used to communicating in German and English, but have to learn the special terminology in this field. (orig.) [de

  12. Using Gaming Equipment to Teach

    Science.gov (United States)

    Curriculum Review, 2009

    2009-01-01

    Gaming equipment (such as Nintendo's Wii[TM]) is making its way to schools and classrooms. However, most of the discussion regarding how to use this technology and integrate it into lesson plans is happening in blogs on the Internet. An advocate of interactive media in the classroom, Dr. Dawn Hawkins, a faculty member for the Art Institute of…

  13. Isotope-equipped measuring instruments

    International Nuclear Information System (INIS)

    Miyagawa, Kazuo; Amano, Hiroshi

    1980-01-01

    In the steel industry, though the investment in isotope-equipped measuring instruments is small as compared with that in machinery, they play important role in the moisture measurement in sintering and blast furnaces, the thickness measurement in rolling process and others in automatic control systems. The economic aspect of the isotope-equipped measuring instruments is described on the basis of the practices in Kimitsu Works of Nippon Steel Corporation: distribution of such instruments, evaluation of economic effects, usefulness evaluation in view of raising the accuracy, and usefulness evaluation viewed from the failure of the isotope instruments. The evaluation of economic effects was made under the premise that the isotope-equipped measuring instruments are not employed. Then, the effects of raising the accuracy are evaluated for a γ-ray plate thickness gauge and a neutron moisture gauge for coke in a blast furnace. Finally, the usefulness was evaluated, assuming possible failure of the isotope-equipped measuring instruments. (J.P.N.)

  14. Hydraulic turbines and auxiliary equipment

    Energy Technology Data Exchange (ETDEWEB)

    Luo Gaorong [Organization of the United Nations, Beijing (China). International Centre of Small Hydroelectric Power Plants

    1995-07-01

    This document presents a general overview on hydraulic turbines and auxiliary equipment, emphasizing the turbine classification, in accordance with the different types of turbines, standard turbine series in China, turbine selection based on the basic data required for the preliminary design, general hill model curves, chart of turbine series and the arrangement of application for hydraulic turbines, hydraulic turbine testing, and speed regulating device.

  15. Seismic fragility levels of nuclear power plant equipment

    International Nuclear Information System (INIS)

    Bandyopadhyay, K.K.; Hofmayer, C.H.

    1987-01-01

    Seismic fragility levels of safety-related electrical and mechanical equipment used in nuclear power plants are discussed. The fragility level is defined as the vibration level corresponding to initiation of equipment malfunctions. The test response spectrum is used as a measure of this vibration level. The fragility phenomenon of an equipment is represented by a number of response spectra corresponding to various failure modes. Analysis methods are described for determination of the fragility level by use of existing test data. Useful conversion factors are tabulated to transform test response spectra from one damping value to another. Results are presented for switch-gears and motor control centers. The capacity levels of these equipment assemblies are observed to be limited by malfunctioning of contactors, motor starters, relays and/or switches. The applicability of the fragility levels, determined in terms of test response spectra, to Seismic Margin Studies and Probabilistic Risk Assessments is discussed and specific recommendations are provided

  16. Customized lifting multiwavelet packet information entropy for equipment condition identification

    International Nuclear Information System (INIS)

    Chen, Jinglong; Zi, Yanyang; He, Zhengjia; Chen, Xuefeng; Zuo, Ming J; Yuan, Jing

    2013-01-01

    Condition identification of mechanical equipment from vibration measurement data is significant to avoid economic loss caused by unscheduled breakdowns and catastrophic accidents. However, this task still faces challenges due to the complexity of equipment and the harsh environment. This paper provides a possibility for equipment condition identification by proposing a method called customized lifting multiwavelet packet information entropy. Benefiting from the properties of multi-resolution analysis and multiple wavelet basis functions, the multiwavelet method has advantages in characterizing non-stationary vibration signals. In order to realize the accurate detection and identification of the condition features, a customized lifting multiwavelet packet is constructed via a multiwavelet lifting scheme. Then the vibration signal from the mechanical equipment is processed by the customized lifting multiwavelet packet transform. The relative energy in each frequency band of the multiwavelet packet transform coefficients that equals a percentage of the whole signal energy is taken as the probability. The normalized information entropy is obtained based on the relative energy to describe the condition of a mechanical system. The proposed method is applied to the condition identification of a rolling mill and a demountable disk–drum aero-engine. The results support the feasibility of the proposed method in equipment condition identification. (paper)

  17. Proterozoic events recorded in quartzite cobbles at Jack Hills, Western Australia: New constraints on sedimentation and source of > 4 Ga zircons

    Science.gov (United States)

    Grange, Marion L.; Wilde, Simon A.; Nemchin, Alexander A.; Pidgeon, Robert T.

    2010-03-01

    Rare heavy mineral bands within quartzite cobbles were identified in two conglomerate units within the Jack Hills belt, Western Australia. Seven zircon-bearing cobbles were analysed from one location (site 152) and three from another (site 154), both approximately 1 km west of the site where zircons in excess of 4 Ga are abundant (W74 'discovery' site). Individual pebbles from the 152 site reveal three distinctive features, containing either zircons > 3.0 Ga in age, 4 Ga was discovered from the entire suite of pebbles, in contrast to the well-studied W74 site. A single detrital zircon with an age of 1220 ± 42 Ma from location 152 is the youngest grain so far reported from sedimentary rocks at Jack Hills. It shows magmatic oscillatory zoning and thus implies at least two sedimentary cycles within the Proterozoic; requiring erosion of an igneous precursor, incorporation into a clastic sediment, induration and subsequent erosion and transport to be hosted in the conglomerate. The nearest source for rocks of this age is the Bangemall Supergroup in the Collier Basin, ˜ 100 km northeast in the Capricorn Orogen. This would imply tectonic interleaving of originally more extensive Bangemall rocks, possibly related to activity along the Cargarah Shear Zone that traverses the Jack Hills belt. The lack of > 4.1 Ga zircons in the pebbles is highly significant, suggesting the immediate source of ancient zircons was no longer present at the Earth's surface. This equates with a general lack of ancient crystals noted in rocks that contain Proterozoic zircons from previous studies and implies that such grains diminish in number as earlier sedimentary rocks were successively recycled.

  18. Analysis of ITER NbTi and Nb3Sn CICCs experimental minimum quench energy with JackPot, MCM and THEA models

    Science.gov (United States)

    Bagni, T.; Duchateau, J. L.; Breschi, M.; Devred, A.; Nijhuis, A.

    2017-09-01

    Cable-in-conduit conductors (CICCs) for ITER magnets are subjected to fast changing magnetic fields during the plasma-operating scenario. In order to anticipate the limitations of conductors under the foreseen operating conditions, it is essential to have a better understanding of the stability margin of magnets. In the last decade ITER has launched a campaign for characterization of several types of NbTi and Nb3Sn CICCs comprising quench tests with a singular sine wave fast magnetic field pulse and relatively small amplitude. The stability tests, performed in the SULTAN facility, were reproduced and analyzed using two codes: JackPot-AC/DC, an electromagnetic-thermal numerical model for CICCs, developed at the University of Twente (van Lanen and Nijhuis 2010 Cryogenics 50 139-148) and multi-constant-model (MCM) (Turck and Zani 2010 Cryogenics 50 443-9), an analytical model for CICCs coupling losses. The outputs of both codes were combined with thermal, hydraulic and electric analysis of superconducting cables to predict the minimum quench energy (MQE) (Bottura et al 2000 Cryogenics 40 617-26). The experimental AC loss results were used to calibrate the JackPot and MCM models and to reproduce the energy deposited in the cable during an MQE test. The agreement between experiments and models confirm a good comprehension of the various CICCs thermal and electromagnetic phenomena. The differences between the analytical MCM and numerical JackPot approaches are discussed. The results provide a good basis for further investigation of CICC stability under plasma scenario conditions using magnetic field pulses with lower ramp rate and higher amplitude.

  19. Development of maintenance equipment for nuclear material fabrication equipment in a highly active hot cell

    Energy Technology Data Exchange (ETDEWEB)

    Park, J. J.; Yang, M. S.; Kim, K. H. and others

    2000-09-01

    This report presents the development of a maintenance system for a highly contaminated nuclear material handling equipment at a hot-cell. This maintenance system has mainly three subsystems - a gamma-radiation measurement module for detecting a gamma-radiation level and identifying its distribution in-situ, a dry-type decontamination device for cleaning up contaminated particles, and a maintenance chamber for isolating contaminated equipment. The mechanical design considerations, controller, capabilities and remote operation and manipulation of the maintenance system are described. Such subsystems developed were installed and tested in the IMEF (Irradiated Material Examination Facility) M6 hot-cell after mock-up tests and performed their specific tasks successfully.

  20. Development of maintenance equipment for nuclear material fabrication equipment in a highly active hot cell

    International Nuclear Information System (INIS)

    Park, J. J.; Yang, M. S.; Kim, K. H. and others

    2000-09-01

    This report presents the development of a maintenance system for a highly contaminated nuclear material handling equipment at a hot-cell. This maintenance system has mainly three subsystems - a gamma-radiation measurement module for detecting a gamma-radiation level and identifying its distribution in-situ, a dry-type decontamination device for cleaning up contaminated particles, and a maintenance chamber for isolating contaminated equipment. The mechanical design considerations, controller, capabilities and remote operation and manipulation of the maintenance system are described. Such subsystems developed were installed and tested in the IMEF (Irradiated Material Examination Facility) M6 hot-cell after mock-up tests and performed their specific tasks successfully

  1. Methodical installations for fast resource testing of reliability of electrotechnical components intended for NPP equipment; Metodicheskie ustanovki dlya uskorennykh roesursnykh ispytanij na nadezhnost ` ehlektrotekhnicheskikh komplektuyushchikh, vkhodyashchikh v sostav oborudovaniya AEhS i yadernykh ustanovok

    Energy Technology Data Exchange (ETDEWEB)

    Shestakov, V S

    1994-12-31

    Installations for testing the electrotechnical equipment, microswitches for mechanical bend tests of cables as well as for high voltage tests of electrotechnical equipment are developed and described.

  2. Alternative Fuels Data Center: Biodiesel Equipment Options

    Science.gov (United States)

    Equipment Options to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Equipment Options on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Equipment Options on Twitter Bookmark Alternative Fuels Data Center: Biodiesel Equipment Options on Google Bookmark Alternative Fuels

  3. 40 CFR 792.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

  4. 40 CFR 160.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

  5. 21 CFR 58.61 - Equipment design.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

  6. 34 CFR 74.34 - Equipment.

    Science.gov (United States)

    2010-07-01

    ... as program income. (e) When acquiring replacement equipment, the recipient may use the equipment to... replacement equipment subject to the approval of the Secretary. (f) The recipient's property management... 34 Education 1 2010-07-01 2010-07-01 false Equipment. 74.34 Section 74.34 Education Office of the...

  7. 20 CFR 437.32 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use.... Procedures for managing equipment (including replacement equipment), whether acquired in whole or in part... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Equipment. 437.32 Section 437.32 Employees...

  8. 45 CFR 2541.320 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... replacement equipment, the grantee or subgrantee may use the equipment to be replaced as a trade-in or sell... replacement equipment), whether acquired in whole or in part with grant funds, until disposition takes place... ensure the highest possible return. (e) Disposition. When original or replacement equipment acquired...

  9. 45 CFR 1174.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

  10. 45 CFR 1157.32 - Equipment.

    Science.gov (United States)

    2010-10-01

    ... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...

  11. The Cost of Maintaining Educational Communications Equipment.

    Science.gov (United States)

    Humphrey, David A.

    Tentative formulas for calculating the cost of maintaining educational communications equipment are proposed. The formulas are based on a survey of campuses of the State University of New York. The survey analyzed the types of equipment to be maintained, types of maintenance, who uses the equipment, who services the equipment, and the cost…

  12. Variability in Light Use Efficiency With Changes in Vegetation Structure and Understory, Using a Temporally Changing Flux Footprint at the BERMS Old Jack Pine Site

    Science.gov (United States)

    Chasmer, L.; Barr, A.; Black, A.; Hopkinson, C.; Kljun, N.; McCaughey, H.; Treitz, P.; Shashkov, A.; Zha, T.

    2006-12-01

    Satellite remote sensing algorithms of vegetation gross primary productivity (GPP) often include a light use efficiency (LUE) term that varies depending on meteorological constraints and biome type. LUE is defined as the carbon fixed per mole of photosynthetically active radiation (PAR) absorbed by the canopy (APAR). LUE estimated using GPP from eddy covariance data is complex and changes over short time periods as the available resources (soil moisture, light, temperature, and nitrogen) vary. An understanding of the variability in LUE will improve local to regional estimates of GPP within complex vegetated land cover types using the variety of remote sensing technologies now available. This study examines variability in LUE and GPP at a mature jack pine site within the Fluxnet-Canada BERMS (Boreal Ecosystem Research and Monitoring Sites) study area using a flux footprint model (Kljun et al. 2004) and airborne lidar data (e.g. Chasmer et al. 2006). Three separate weeks of high frequency eddy covariance data are analyzed for June, July, and August 2002 to capture changes in photosynthesis and carbon uptake through the growing season with variations in precipitation and soil moisture. Footprint estimates are derived in half-hourly resolution to provide information on the spatial and temporal variation of the sources of measured C-fluxes. Airborne lidar directly samples ground topography and vegetation structure (i.e., canopy and understory height, gaps between trees, base of canopy), and may provide information on soil moisture and drainage at the ground surface via absorbed and reflected laser pulse energy. Two questions will be addressed specific to net ecosystem productivity (NEP) of the site as a whole, including parts of the ecosystem that may not be properly represented using eddy covariance techniques. These are: 1. How does C uptake and respiration spatially and temporally vary across the jack pine site? 2. How do vegetation characteristics vary with

  13. Growth of the Pacific jack Caranx caninus (Pisces: Carangidae from the coast of Colima, México

    Directory of Open Access Journals (Sweden)

    Elaine Espino Barr

    2008-03-01

    Full Text Available The Pacific jack Caranx caninus is a common species fished by artisanal fishermen off the coast of Colima, México. During 2002, monthly samples of morphometric data and otoliths were taken to determine age and growth. Seven age groups were identified. The highest growth, 14.4 cm, takes place during the first year of life. During the second year, C. caninus grows 11.76 cm; the third year 9.61 cm; the fourth 7.85 cm; the fifth 6.41 cm and sixth year 5.24 cm. The constants of von Bertalanffy´s growth equation were: L∞ = 83.26 cm, W∞ = 18.138 g, K = 0.202, t o = -0.283 and A0.95 = 15 years. Growth curves of other species of the same genus were calculated in order to compare them with the one obtained in the present work. The gonadosomatic index presented higher values during November and May. The periods of more intensive feeding are from August to February. Rev. Biol. Trop. 56 (1: 171-179. Epub 2008 March 31.El jurel Caranx caninus es una especie común que se captura en la pesca artesanal frente a las costas de Colima, México. Mensualmente, durante 2002, se tomaron datos morfométricos y muestras de otolitos para determinar la edad y el crecimiento. Se encontraron siete grupos de edad; durante el primer año de vida se da el mayor crecimiento, hasta 14.4 cm. Durante el segundo año, C. caninus crece 11.76 cm; el tercero 9.61 cm; el cuarto 7.85 cm; el quinto 6.41 cm y el último año crece 5.24 cm. Las constantes de la ecuación de crecimiento de von Bertalanffy fueron: L∞ = 83.26 cm, W∞ = 18.138 g, K = 0.202, to = -0.283 y la longevidad A0.95 = 15 años. Las curvas de crecimiento de otras especies del mismo género se compararon con las obtenidas en el presente trabajo. El índice gonadosomático presentó valores más altos durante noviembre y mayo. Los periodos de tiempo de alimentación más intensa son de agosto a febrero.

  14. Desidratação osmótica de fatias de jaca Osmotic dehydration of jack fruit slices

    Directory of Open Access Journals (Sweden)

    Maria Elita Martins Duarte

    2012-09-01

    Full Text Available O presente trabalho foi realizado com o objetivo de estudar a cinética e modelagem do processo de desidratação osmótica de fatias de jaca em geometria plana. O tratamento osmótico foi conduzido a 43 ºC, com agitação, utilizando-se de soluções de sacarose, nas concentrações de 40 e 50 ºBrix. O estudo da cinética de desidratação osmótica mostrou que na solução de sacarose a 50 ºBrix o valor da perda de água (WL foi maior ao final de 28,5 horas de processo (68,5% b.u para 40,2% b.u., ligeiramente superior ao encontrado para a solução de sacarose a 40 ºBrix, (68,5% b.u para 43% b.u.. Comportamento contrário ocorreu para o ganho de sólidos (SG. O ajuste dos dados experimentais foi realizado através dos modelos de Page e Fick. Pela análise da equação de Fick, verificou-se que os coeficientes de difusividade efetiva foram 0,5837 e 0,6677 mm² min-1 para 40 e 50 ºBrix, respectivamente.The present work was undertaken with the objective of studying the kinetics and the osmotic-dehydration modeling of slices of jack-fruit in a flat layout. The osmotic treatment was carried out at 43ºC, employing agitation, and using sucrose solutions at concentrations of 40º and 50º Brix. The study of the kinetics of osmotic dehydration showed that in the sucrose solution at 50º Brix, the value of the water-loss (WL was higher after 28.5 hours of processing (68.5% wb to 40.2% wb , slightly higher than that found for the sucrose solution at 40º Brix (68.5% wb to 43% wb. The opposite behavior was observed for the gain in solids (SG. Adjustment of the experimental data was done using the Page and Fick models. From the analysis of the Fick equation, it was found that the effective diffusivity coefficients were 0.5837 and 0.6677 mm² min-1 for 40º and 50º Brix, respectively.

  15. Chemical decontamination solutions: Effects on PWR equipment

    International Nuclear Information System (INIS)

    Pezze, C.M.; Colvin, E.R.; Aspden, R.G.

    1992-01-01

    A critical objective for the nuclear industry is the reduction of personnel exposure to radiation. Reductions have been achieved through industry's radiation management programs including training and radiation awareness concepts. Increased plant maintenance and higher radiation fields at many sites continue to raise concerns. To alleviate the radiation exposure problem, the sources of radiation which contribute to personnel exposure must be removed from the plant. A feasible was of significantly reducing these sources from a Pressurized Water Reactor (PWR) is to chemically decontaminate the entire reactor coolant system (RCS). A program was conducted to determine the technical acceptability of using certain dilute chemical solvent processes for full RCS chemical decontamination. The two processes evaluated were CAN-DEREM and LOMI. The purpose of the program was to define and complete a systematic evaluation of the major issues that need to be addressed for the successful decontamination of the entire RCS and affected portions of the auxiliary systems of a four-loop PWR system. A test program was designed to evaluate the corrosion effects of the two decontamination processes under expected plant conditions. Materials and sample configurations dictated by generic PWR components were evaluated. The testing also included many standard corrosion coupons. The test data were then used to assess the impact of chemical decontamination on the physical condition and operability of the components, equipment and mechanical systems that make up the RCS. An overview of the test program, sample configurations, data and engineering evaluations is presented. The data demonstrate that through detailed engineering evaluations of corrosion data and equipment function, the impact of full RCS chemical decontamination on plant equipment is established

  16. Video equipment of tele dosimetry and audio

    International Nuclear Information System (INIS)

    Ojeda R, M.A.; Padilla C, I.

    2007-01-01

    To develop a work in an area with high radiation, it requires of a detailed knowledge of the surroundings work, a communication and effective vision, a near dosimetric control. In a work where the spaces variables and reduced accesses exist, noise that hinders the communication, defendant operative condition, radiation field and taking of decision, it is necessary to have tools that allow a total control of the environment to make opportune and effective decisions, there where the task is developed. Under this elementary concept, it was developed in the Laguna Verde Central a project that it allowed a mechanism, interactive of control in spaces complex; to see, to hear, to speak, to measure. This concept takes to the creation of an equipped system with closed circuit of television, wireless communication systems, tele dosimetry wireless systems, VHS and DVD recording equipment, uninterrupted energy units. The system requires of an electric power socket, and the installation of two cables by CCTV camera. The system is mobilized by a person. He puts on in operation in 5 minutes using a verification list. The concept was developed in the project denominated VETA-1, (Video Equipment of Tele dosimetry and Audio). It is objective of this work to present before the society the development of the VETA-1 tool that conclude in their first prototype in May of the present year. The VETA-1 project arises by a necessity of optimizing dose, it is an ALARA tool, with a countless applications, like it was proven in the 12 recharge stop of the Unit 1. The VETA-1 project integrate a recording system, with the primary end of analyzing in the place where the task is developed the details for an effective and opportune decision, but the resulting information is of utility for the personnel's training and the planning of future works. The VETA-1 system is an ALARA tool of quick response control. (Author)

  17. [Equipment and technology in robotics].

    Science.gov (United States)

    Murphy, Declan; Challacombe, Ben; Nedas, Tim; Elhage, Oussama; Althoefer, Kaspar; Seneviratne, Lakmal; Dasgupta, Prokar

    2007-05-01

    We review the evolution and current status of robotic equipment and technology in urology. We also describe future developments in the key areas of virtual reality simulation, mechatronics and nanorobotics. The history of robotic technology is reviewed and put into the context of current systems. Experts in the associated fields of nanorobotics, mechatronics and virtual reality simulation simulation review the important future developments in these areas.

  18. Remote handling equipment for SNS

    International Nuclear Information System (INIS)

    Poulten, B.H.

    1983-01-01

    This report gives information on the areas of the SNS, facility which become highly radioactive preventing hands-on maintenance. Levels of activity are sufficiently high in the Target Station Area of the SNS, especially under fault conditions, to warrant reactor technology to be used in the design of the water, drainage and ventilation systems. These problems, together with the type of remote handling equipment required in the SNS, are discussed

  19. Margins related to equipment design

    International Nuclear Information System (INIS)

    Devos, J.

    1994-01-01

    Safety margins related to design of reactor equipment are defined according to safety regulations. Advanced best estimate methods are proposed including some examples which were computed and compared to experimental results. Best estimate methods require greater computation effort and more material data but give better variable accuracy and need careful experimental validation. Simplified methods compared to the previous are less sensitive to material data, sometimes are more accurate but very long to elaborate

  20. Temperature radiation measuring equipment. Temperaturstrahlungsmessgeraet

    Energy Technology Data Exchange (ETDEWEB)

    Lotzer, W

    1981-01-22

    The invention is concerned with a temperature radiation measuring equipment for non-contact temperature measurement by the light intensity variation method, with a photoelectric resistance as the measuring element. By having a circuit with a transistor, the 'dark resistance' occurring in the course of time is compensated for and thus gives a genuine reading (ie. the voltage drop across the photoelectric resistance remains constant).

  1. CERN computing equipment for Senegal

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On 26 May, CERN once again had the honour of donating computing equipment to a foreign institute.   This time, around 100 servers and five network hubs were sent to Senegal, making it the seventh country, after Morocco, Ghana, Bulgaria, Serbia, Egypt and the Philippines, to receive a donation of computing equipment from the Organization. The official ceremony was held at CERN on 26 May in the presence of the Director-General, Rolf Heuer, and Senegal's ambassador to Geneva, Fodé Seck, who both expressed their enthusiasm for the project. The equipment is intended for Cheikh Anta Diop University (UCAD) in Dakar and will be of particular use to students attending the African School of Fundamental Physics and its Applications (ASP 2014) taking place from 3 to 23 August, for which CERN is a partner. The ASP allows a large number of African students to hone their skills in high-energy physics and to forge professional links with fellow physicists in Africa and Europe. ...

  2. Flaw detection of welded joints in NPP equipment assembly

    International Nuclear Information System (INIS)

    Kesler, N.A.; Polevik, V.A.; Orlov, N.S.

    1984-01-01

    State of the art and prospects of development of ultrasonic and radiography testing of welded joints for quality used in NPP equipment assembly are considered. Recommendations are given on reducing the labour content with the use of these methods. Specifications for the developed facilities intended for automation and mechanization of the described quality control methods are presented

  3. Non-standard equipment for construction of vertical shafts

    Science.gov (United States)

    Yagodkin, F. I.; Prokopov, A. Y.; Pleshko, M. S.; Pankratenko, A. N.

    2017-10-01

    The article deals with the modern problems of construction and reconstruction of vertical shafts of mines, which require innovative technical solutions in the mechanization of mining operations. The examples developed by the authors of the original equipment and technologies, are successfully implemented for the mining industry in Russia.

  4. Biofilms associated with poultry processing equipment.

    Science.gov (United States)

    Lindsay, D; Geornaras, I; von Holy, A

    1996-01-01

    Aerobic and Gram-negative bacteria were enumerated on non-metallic surfaces and stainless steel test pieces attached to equipment surfaces by swabbing and a mechanical dislodging procedure, respectively, in a South African grade B poultry processing plant. Changes in bacterial numbers were also monitored over time on metal test pieces. The highest bacterial counts were obtained from non-metallic surfaces such as rubber fingered pluckers and plastic defeathering curtains which exceeded the highest counts found on the metal surfaces by at least 1 log CFU cm-2. Gram-negative bacterial counts on all non-metallic surface types were at least 2 log CFU cm-2 lower than corresponding aerobic plate counts. On metal surfaces, the highest microbial numbers were obtained after 14 days exposure, with aerobic plate counts ranging from 3.57 log CFU cm-2 to 5.13 log CFU cm-2, and Gram-negative counts from 0.70 log CFU cm-2 to 3.31 log CFU cm-2. Scanning electron microscopy confirmed the presence of bacterial cells on non-metallic and metallic surfaces associated with poultry processing. Rubber 'fingers', plastic curtains, conveyor belt material and stainless steel test surfaces placed on the scald tank overflow and several chutes revealed extensive and often confluent bacterial biofilms. Extracellular polymeric substances, but few bacterial cells were visible on test pieces placed on evisceration equipment, spinchiller blades and the spinchiller outlet.

  5. Investigation equipment and methods used by Posiva

    International Nuclear Information System (INIS)

    Oehberg, A.

    2006-10-01

    Posiva Oy, a company jointly owned by TVO and Fortum, submitted an application for the Decision in Principle to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the Decision in Principle on the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground research facility, ONKALO, for rock characterisation for the final disposal of spent nuclear fuel will be constructed. The construction of the ONKALO access tunnel was started in September 2004. This report describes the investigation methods and equipment developed and used by Posiva Oy during the confirming site investigations from the surface. The report covers the areas of drilling of deep investigation holes, geophysical loggings, geophysical ground and tunnel surveys, hydrogeological and hydrogeochemical as well as rock mechanical methods. Emphasis is given on those equipment and methods developed by Posiva and those that have frequently and recently been used in the Posiva's characterisation programmes including methods applied during excavation of ONKALO access tunnel. The database used for the field investigation data is also briefly described in this report. (orig.)

  6. JCE Online: Equipment Buyers Guide

    Science.gov (United States)

    Holmes, Jon L.

    1999-01-01

    The Equipment Buyers Guide was edited by Jo Rita Jordan. The new Equipment Buyers Guide, bound into the back of this issue, is also a new resource of JCE Internet. This resource provides an online source for the information contained in the printed guide. Placing this information online allows us to regularly update it and to provide live links to the suppliers' WWW sites. The organization of the online version parallels that of the print version. There is an alphabetical list of suppliers and a categorical listing. Links to these lists are provided on every page in the left-hand navigation bar. To quickly find information about a particular supplier, you click Supplier List, click the letter that begins the supplier's name, and scroll through the list to find the supplier. To find which suppliers provide a particular type of instrument or equipment, use the Categories link; click the category of the equipment you are looking for and then click the link to a supplier. You will then be taken to an alphabetical supplier listing page where you can scroll until you find the particular supplier of the item for which you are looking. Once you have found a supplier, the online Equipment Buyers Guide gives you the traditional contact information. But in addition, you also get one-click access to the WWW sites of the suppliers that have them. Depending on the site, you should be able to find information about the items that you seek and may even be able to order the items online! We think that you will find the online version of the Equipment Buyers Guide useful. To make it more useful, please send your suggestions, any errors or omissions you find, and any additional categories to the editor at jjordan@world.std.com The online Equipment Buyers Guide can be found at JCE Online at http://JChemEd.chem.wisc.edu/JCEWWW/Resources/EBG/ JCE Online in '99 JCE Online is your online source of "all things JCE". In order to provide you with an even more useful online resource, JCE

  7. Used energy-related laboratory equipment grant program for institutions of higher learning. Eligible equipment catalog

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.

  8. Data center equipment location and monitoring system

    DEFF Research Database (Denmark)

    2011-01-01

    A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to a equipment rack controller on the equipment rack. The equipment rack controllers then link over a local area network to a central control computer. The central control computer provides an operator interface......, and runs a software application program that communicates with the equipment rack controllers. The software application program of the central control computer stores IDs of the equipment rack controllers and each of its connected electronic ID tags in a database.; The software application program...

  9. The effects of combination of Eurycoma longifolia Jack ethanolic extract and doxorubicine on hematological profile in rats given by 7,12-dimethylbenz(a)anthracene

    Science.gov (United States)

    Nurani, L. H.; Mursyidi, A.; Widyarini, S.; Rohman, A.

    2017-11-01

    Doxorubicin (Dox) is known as anticancer drug commonly used for cancer treatment. Eurycoma longifolia Jack or Pasakbumi was reported to have chemopreventive effect. In cancer patients, there are some dysfunctions of blood parameter, therefore some hematologic tests are needed to monitor cancer patients. In this study, the effects of combination of ethanolic extract of E. longifolia Jack (EEE) and Dox on hematologic profiles were investigated in rats injected by DMBA. Rats were divided into eight groups. Group I was normal group; Group II, rats were treated with extract dose 100 mg/kgbw; Groups III, IV, V, VI, VII and VIII, rats were treated with Dox, DMBA, DMBA+Dox, DMBA+EEE, DMBA+Dox +EEE, and Dox+EEE, respectively. DMBA administration orally was conducted twice a week for 5 weeks. At 16th week of treatments, bloods were taken from orbitalis sinus for hematologicals profile (levels of Hb, erytrocyte, hematocrite, leukocyte, MCV, MCH, and differencial leucocyte count) measurements. These data were analyzed by one way ANOVA followed by LSD test. DMBA administration significantly decreased the hematological profiles compared to the normal group, except in lymphocyte level. Rats treated with extract and extract+Dox were able to increase the hematological profile compared to rats given by DMBA only. Based on these findings it can be concluded that the combination of EEE and Dox potentially increase hematological profile of rats given by DMBA.

  10. Clinical Performance and Safety of 108 SpineJack Implantations: 1-Year Results of a Prospective Multicentre Single-Arm Registry Study

    Directory of Open Access Journals (Sweden)

    David Noriega

    2015-01-01

    Full Text Available This prospective, consecutive, multicentre observational registry aimed to confirm the safety and clinical performance of the SpineJack system for the treatment of vertebral compression fractures (VCF of traumatic origin. We enrolled 103 patients (median age: 61.6 years with 108 VCF due to trauma, or traumatic VCF with associated osteoporosis. Primary outcome was back pain intensity (VAS. Secondary outcomes were Oswestry Disability Index (ODI, EuroQol-VAS, and analgesic consumption. 48 hours after surgery, a median relative decrease in pain intensity of 81.5% was observed associated with a significant reduction in analgesic intake. Improvements in disability (91.3% decrease in ODI score and in quality of life (increase 21.1% of EQ-VAS score were obtained 3 months after surgery. All results were maintained at 12 months. A reduction in the kyphotic angulation was observed postoperatively (-5.4±6.3°; p<0.001, remained at 12 months (-4.4±6.0°, p=0.002. No adverse events were implant-related and none required device removal. Three patients (2.9% experienced procedure-related complications. The overall adjacent fracture rate up to 1 year after surgery was 2.9%. The SpineJack procedure is an effective, low-risk procedure for patients with traumatic VCF allowing a fast and sustained improvement in quality of life over 1 year after surgery.

  11. Development of remote automatic equipment for BWR power plants

    International Nuclear Information System (INIS)

    Sasaki, Masayoshi

    1984-01-01

    The development of remote control, automatic equipment for nuclear power stations has been promoted to raise the rate of operation of plants by shortening regular inspection period, to improve the safety and reliability of inspection and maintenance works by mechanization, to reduce the radiation exposure dose of workers and to reduce the manpower required for works. The taking-off of control rod drives from reactors and fixing again have been mechanized, but the disassembling, cleaning, inspection and assembling of control rod drives are manually carried out. Therefore, Hitachi Ltd. has exerted effort to develop the automatic equipment for this purpose. The target of development, investigation, the construction and function of the equipment, the performance and the effect of adopting it are reported. The equipment for the volume reduction of spent fuel channel boxes and spent control rods is developed since these are major high level radioactive solid wastes, and their apparent volume is large. Also the target of development, investigated things, the construction and function of the equipment, the performance and the effect of adopting it are reported. (Kako, I.)

  12. 30 CFR 75.1722 - Mechanical equipment guards.

    Science.gov (United States)

    2010-07-01

    ... may cause injury to persons shall be guarded. (b) Guards at conveyor-drive, conveyor-head, and conveyor-tail pulleys shall extend a distance sufficient to prevent a person from reaching behind the guard and becoming caught between the belt and the pulley. (c) Except when testing the machinery, guards...

  13. 30 CFR 77.400 - Mechanical equipment guards.

    Science.gov (United States)

    2010-07-01

    ... shall be guarded. (b) Overhead belts shall be guarded if the whipping action from a broken line would be hazardous to persons below. (c) Guards at conveyor-drive, conveyor-head, and conveyor-tail pulleys shall... between the belt and the pulley. (d) Except when testing the machinery, guards shall be securely in place...

  14. Direct ultimate disposal of spent fuel elements. Mechanical equipment tests

    International Nuclear Information System (INIS)

    Filbert, W.; Schrimpf, C.

    1990-02-01

    Simulation of the shaft transport of waste forms is described. Proceeding from a concept of a shaft hoist with a payload of 85 t, the applicability of the state of the art of essential components, such as hoisting machine, cage and hoisting cables, to such payloads is described. For these components a test stand has been planned which meets safety-related regulations. (DG) [de

  15. Equipment monitoring and diagnosis of their mechanical condition

    International Nuclear Information System (INIS)

    Morel, J.; Monnier, B.

    1994-01-01

    The main objectives of reactor monitoring are reviewed and the three monitoring types are described: reception controls and alarms, periodical controls, and specific monitoring. The monitoring process is then presented: information acquisition, dysfunction detection and diagnosis, risk analysis and maintenance action determination. Diagnosis assistance is now automated with expert systems such as DIVA (shaft vibration diagnosis) and DIAPO (primary pump diagnosis). Several application examples at EDF are described: SEXTEN reactor containment tightness monitoring, large and small-size turbo-machine monitoring, reactor inner structure monitoring, loose part detection in the primary circuit. All these informations will be centralized in a general monitoring and diagnosis assistance station. 3 fig

  16. A Perspective on Equipment Design for Fusion Remote Handling

    International Nuclear Information System (INIS)

    Mills, S.; Haist, B.; Hamilton, D.

    2006-01-01

    For 8 years, JET remote operations have become more capable and confident. Many tasks have been successfully completed, even those never intended to be remote maintenance activities. The general approach to the provision of remote handling equipment at JET has been the preferred use of commercially-off-the-shelf equipment. In the areas of electrical, electronic, software and control this approach has been generally achievable. However, in the area of mechanical equipment it has been more difficult. In particular the RH tooling has been almost entirely bespoke as its requirements are highly sensitive to the design of the JET component being handled and there are many design variations. Hence, JET has required the design and manufacture of over 700 types of bespoke RH equipment. This paper will discuss the experience of introducing and developing remote handling mechanical equipment for JET. The paper will cover the relationship between the remote handling equipment and the JET component design and the potential for improving the design function. A major lesson from the introduction of remote handling to JET has been demonstration of the very close interdependency of the design of JET components with design of remote handling tooling. The JET remote handling manual was originally introduced as the vehicle to ensure remote handling compatibility by the introduction of standards. Experience has shown that in general the remote handling manual approach has been insufficient. Future fusion machines will be much more complex than JET and will demand even greater remote handling compatibility. This paper will discuss possible methods for improving this process. Equipment operating in a high radiation environment must be dependable It may spend part of its time in areas that would be extremely difficult to recover from in the case of failure. The equipment may also have a high duty cycle to minimise shutdown times and probably cannot be manually inspected on a frequent

  17. Basement of Structure, Main Power and Design Parameters of Mechanism of Removing Sections of Mechanized Sets of Knife Plane Installation

    Science.gov (United States)

    Sysoev, N. I.; Turuk, Yu V.; Kolesnichenko, I. Y.; Lugantsev, B. B.

    2017-10-01

    The reasons for the failure of the pitch stability of the knife-plane installation due to the action of extreme effort in the plane of the seam from the conveyor side on the mechanism of removing sections of mechanized sets are shown. The technique for determining this effort is presented. The constructions of the adaptive mechanisms of the removing sections of mechanized sets with the basements of catamaran type, in the constrictions of which elastic elements (rods) are used, are considered. The constructions of the mechanism of removing a section of the mechanized set with the basement of catamaran type in which the stock of the hydraulic jack is connected with the band loop through the movable rods intermediate basement with a link are worked out. The intermediate basement unloads the stock of the hydraulic jack of the moving installation from the side curving efforts, caused by the action of lateral forces in the plane of the seam on the conveyor side. It increases the reliability and efficiency of work of the knife plane mechanized complex.

  18. Reactor vital equipment determination techniques

    International Nuclear Information System (INIS)

    Bott, T.F.; Thomas, W.S.

    1983-01-01

    The Reactor Vital Equipment Determination Techniques program at the Los Alamos National Laboratory is discussed. The purpose of the program is to provide the Nuclear Regulatory Commission (NRC) with technical support in identifying vital areas at nuclear power plants using a fault-tree technique. A reexamination of some system modeling assumptions is being performed for the Vital Area Analysis Program. A short description of the vital area analysis and supporting research on modeling assumptions is presented. Perceptions of program modifications based on the research are outlined, and the status of high-priority research topics is discussed

  19. Review of equipment aging theory and technology. Final report

    International Nuclear Information System (INIS)

    Carfagno, S.P.; Gibson, R.J.

    1980-09-01

    The theory and technology of equipment aging is reviewed, particularly as they relate to the qualification of safety-system equipment for nuclear power generating stations. A fundamental degradation model is developed, and its relation to more restricted models (e.g., Arrhenius and inverse-stress models) is shown. The most common theoretical and empirical models of aging are introduced, and limitations on their practical application are analyzed. Reliability theory and its application to the acceleration of aging are also discussed. A compendium of aging data for materials and components, including degradation mechanisms, failure modes and activation energies, is included

  20. Quality assurance procedures in radiotherapy - IEC specifications for equipment

    Energy Technology Data Exchange (ETDEWEB)

    Rassow, J; Klieber, E

    1986-08-01

    The International Electrotechnical Commission (IEC) worked out international standards for requirements and tests of electrical, mechanical and radiation safety as well as for definition and tests of functional performance characteristics of radiotherapy equipments (medical electron accelerators, gamma beam teletherapy and afterloading equipments, simulators and accessories) and for clinical dosimeters and terminology for medical radiology. A survey is given on the actual state of standardization projects. The problems of such standards are shown for the standard for functional performance characteristics of medical electron accelerators as example.