Safety assessment and verification for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2001-01-01

This publication supports the Safety Requirements on the Safety of Nuclear Power Plants: Design. This Safety Guide was prepared on the basis of a systematic review of all the relevant publications including the Safety Fundamentals, Safety of Nuclear Power Plants: Design, current and ongoing revisions of other Safety Guides, INSAG reports and other publications that have addressed the safety of nuclear power plants. This Safety Guide also provides guidance for Contracting Parties to the Convention on Nuclear Safety in meeting their obligations under Article 14 on Assessment and Verification of Safety. The Safety Requirements publication entitled Safety of Nuclear Power Plants: Design states that a comprehensive safety assessment and an independent verification of the safety assessment shall be carried out before the design is submitted to the regulatory body. This publication provides guidance on how this requirement should be met. This Safety Guide provides recommendations to designers for carrying out a safety assessment during the initial design process and design modifications, as well as to the operating organization in carrying out independent verification of the safety assessment of new nuclear power plants with a new or already existing design. The recommendations for performing a safety assessment are suitable also as guidance for the safety review of an existing plant. The objective of reviewing existing plants against current standards and practices is to determine whether there are any deviations which would have an impact on plant safety. The methods and the recommendations of this Safety Guide can also be used by regulatory bodies for the conduct of the regulatory review and assessment. Although most recommendations of this Safety Guide are general and applicable to all types of nuclear reactors, some specific recommendations and examples apply mostly to water cooled reactors. Terms such as 'safety assessment', 'safety analysis' and 'independent

Health and safety plan for the Isotopes Facilities Deactivation Project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1996-08-01

This HASP describes the process for identifying the requirements, written safety documentation, and procedures for protecting personnel involved in the Isotopes Facilities Deactivation Project. Objective of this project is to place 19 former isotope production facilities at ORNL in a safe condition in anticipation of an extended period of minimum surveillance and maintenance

Safety evaluation of small samples for isotope production

International Nuclear Information System (INIS)

Sharma, Archana; Singh, Tej; Varde, P.V.

2015-09-01

Radioactive isotopes are widely used in basic and applied science and engineering, most notably as environmental and industrial tracers, and for medical imaging procedures. Production of radioisotope constitutes important activity of Indian nuclear program. Since its initial criticality DHRUVA reactor has been facilitating the regular supply of most of the radioisotopes required in the country for application in the fields of medicine, industry and agriculture. In-pile irradiation of the samples requires a prior estimation of the sample reactivity load, heating rate, activity developed and shielding thickness required for post irradiation handling. This report is an attempt to highlight the contributions of DHRUVA reactor, as well as to explain in detail the methodologies used in safety evaluation of the in pile irradiation samples. (author)

The role of risk assessment and safety analysis in integrated safety assessments

International Nuclear Information System (INIS)

Niall, R.; Hunt, M.; Wierman, T.E.

1990-01-01

To ensure that the design and operation of both nuclear and non- nuclear hazardous facilities is acceptable, and meets all societal safety expectations, a rigorous deterministic and probabilistic assessment is necessary. An approach is introduced, founded on the concept of an ''Integrated Safety Assessment.'' It merges the commonly performed safety and risk analyses and uses them in concert to provide decision makers with the necessary depth of understanding to achieve ''adequacy.'' 3 refs., 1 fig

Scoping assessment on medical isotope production at the Fast Flux Test Facility

International Nuclear Information System (INIS)

Scott, S.W.

1997-01-01

The Scoping Assessment addresses the need for medical isotope production and the capability of the Fast Flux Test Facility to provide such isotopes. Included in the discussion are types of isotopes used in radiopharmaceuticals, which types of cancers are targets, and in what way isotopes provide treatment and/or pain relief for patients

Scoping assessment on medical isotope production at the Fast Flux Test Facility

Energy Technology Data Exchange (ETDEWEB)

Scott, S.W.

1997-08-29

The Scoping Assessment addresses the need for medical isotope production and the capability of the Fast Flux Test Facility to provide such isotopes. Included in the discussion are types of isotopes used in radiopharmaceuticals, which types of cancers are targets, and in what way isotopes provide treatment and/or pain relief for patients.

Assessment of Safety Culture

International Nuclear Information System (INIS)

Bilic Zabric, T.; Kavsek, D.

2006-01-01

A strong safety culture leads to more effective conduct of work and a sense of accountability among managers and employees, who should be given the opportunity to expand skills by training. The resources expended would thus result in tangible improvements in working practices and skills, which encourage further improvement of safety culture. In promoting an improved safety culture, NEK has emphasized both national and organizational culture with an appropriate balance of behavioural sciences and quality management systems approaches. In recent years there has been particular emphasis put on an increasing awareness of the contribution that human behavioural sciences can make to develop good safety practices. The purpose of an assessment of safety culture is to increase the awareness of the present culture, to serve as a basis for improvement and to keep track of the effects of change or improvement over a longer period of time. There is, however, no single approach that is suitable for all purposes and which can measure, simultaneously, all the intangible aspects of safety culture, i.e. the norms, values, beliefs, attitudes or the behaviours reflecting the culture. Various methods have their strengths and weaknesses. To prevent significant performance problems, self-assessment is used. Self-assessment is the process of identifying opportunities for improvement actively or, in some cases, weaknesses that could cause more serious errors or events. Self-assessments are an important input to the corrective action programme. NEK has developed questionnaires for safety culture self-assessment to obtain information that is representative of the whole organization. Questionnaires ensure a greater degree of anonymity, and create a less stressful situation for the respondent. Answers to questions represent the more apparent and conscious values and attitudes of the respondent. NEK proactively co-operates with WANO, INPO, IAEA in the areas of Safety Culture and Human

Safety assessment, safety performance indicators at the Paks Nuclear Power Plant

International Nuclear Information System (INIS)

Baji, C.; Vamos, G.; Toth, J.

2001-01-01

The Paks Nuclear Power Plant has been using different methods of safety assessment (event analysis, self-assessment, probabilistic safety analysis), including performance indicators characterizing both operational and safety performance since the early years of operation of the plant. Regarding the safety performance, the indicators include safety system performance, number of scrams, release of radioactive materials, number of safety significant events, industrial safety indicator, etc. The Paks NPP also reports a set of ten indicators to WANO Performance Indicator Programme which, among others, include safety related indicators as well. However, a more systematic approach to structuring and trending safety indicators is needed so that they can contribute to the enhancement of the operational safety. A more comprehensive set of indicators and a systematic evaluation process was introduced in 1996. The performance indicators framework proposed by the IAEA was adapted to Paks in this year to further improve the process. Safety culture assessment and characterizing safety culture is part of the assessment process. (author)

IAEA safety requirements for safety assessment of fuel cycle facilities and activities

International Nuclear Information System (INIS)

Jones, G.

2013-01-01

The IAEA's Statute authorises the Agency to establish standards of safety for protection of health and minimisation of danger to life and property. In that respect, the IAEA has established a Safety Fundamentals publication which contains ten safety principles for ensuring the protection of workers, the public and the environment from the harmful effects of ionising radiation. A number of these principles require safety assessments to be carried out as a means of evaluating compliance with safety requirements for all nuclear facilities and activities and to determine the measures that need to be taken to ensure safety. The safety assessments are required to be carried out and documented by the organisation responsible for operating the facility or conducting the activity, are to be independently verified and are to be submitted to the regulatory body as part of the licensing or authorisation process. In addition to the principles of the Safety Fundamentals, the IAEA establishes requirements that must be met to ensure the protection of people and the environment and which are governed by the principles in the Safety Fundamentals. The IAEA's Safety Requirements publication 'Safety Assessment for Facilities and Activities', establishes the safety requirements that need to be fulfilled in conducting and maintaining safety assessments for the lifetime of facilities and activities, with specific attention to defence in depth and the requirement for a graded approach to the application of these safety requirements across the wide range of fuel cycle facilities and activities. Requirements for independent verification of the safety assessment that needs to be carried out by the operating organisation, including the requirement for the safety assessment to be periodically reviewed and updated are also covered. For many fuel cycle facilities and activities, environmental impact assessments and non-radiological risk assessments will be required. The

Safety assessment of Department of Energy nuclear reactors

International Nuclear Information System (INIS)

1981-03-01

One of the first tasks of the NFPQT Committee was to determine which DOE reactors would be assessed. The Committee determined that in view of the limited time available to conduct the assessment, 13 DOE reactors were of such size (physical, power or fission product inventory) to warrant review. This determination was approved by the Under Secretary. A decision was also made in the cases of three weapons material production reactors, C, K and P, to concentrate on the K reactor only, since all three are of the same basic design, have the same operating features, are all at the same site, and are all operated by the same contractor. The assessment was accomplished in the following ways: reviewing the results of assessments conducted by the DOE organizations with reactor safety responsibilities, which were undertaken in compliance with the request of the various program directors; reviewing selected documents that were requested by the Committee and assembled at DOE Headquarters; interviewing DOE Headquarters and Field Office personnel; and conducting on-site reviews of four reactors located at four different sites. The four reactors for on-site reviews were: Advanced Test Reactor (ATR); K Production Reactor; High Flux Beam Reactor (HFBR); and High Flux Isotope Reactor (HFIR). Specific findings and recommendations from the assessment are presented

Experiences in assessing safety culture

International Nuclear Information System (INIS)

Spitalnik, J.

2002-01-01

Based on several Safety Culture self-assessment applications in nuclear organisations, the paper stresses relevant aspects to be considered when programming an assessment of this type. Reasons for assessing Safety Culture, basic principles to take into account, necessary resources, the importance of proper statistical analyses, the feed-back of results, and the setting up of action plans to enhance Safety Culture are discussed. (author)

OSART Independent Safety Culture Assessment (ISCA) Guidelines

International Nuclear Information System (INIS)

2016-01-01

Safety culture is understood as an important part of nuclear safety performance. This has been demonstrated by the analysis of significant events such as Chernobyl, Davis Besse, Vandellos II, Asco, Paks, Mihamma and Forsmark, among others. In order to enhance safety culture, one essential activity is to perform assessments. IAEA Safety Standard Series No. GS-R-3, The Management System for Facilitites and Activities, states requirements for continuous improvement of safety culture, of which self, peer and independent safety culture assessments constitute an essential part. In line with this requirement, the Independent Safety Culture Assessment (ISCA) module is offered as an add-on module to the IAEA Operational Safety Review Team (OSART) programme. The OSART programme provides advice and assistance to Member States to enhance the safety of nuclear power plants during commissioning and operation. By including the ISCA module in an OSART mission, the receiving organization benefits from the synergy between the technical and the safety culture aspects of the safety review. The joint operational safety and safety culture assessment provides the organization with the opportunity to better understand the interactions between technical, human, organizational and cultural aspects, helping the organization to take a systemic approach to safety through identifying actions that fully address the root causes of any identified issue. Safety culture assessments provide insight into the fundamental drivers that shape organizational patterns of behaviour, safety consciousness and safety performance. The complex nature of safety culture means that the analysis of the results of such assessments is not as straightforward as for other types of assessment. The benefits of the results of nuclear safety culture assessments are maximized only if appropriate tools and guidance for these assessments is used; hence, this comprehensive guideline has been developed. The methodology explained

Metrics design for safety assessment

NARCIS (Netherlands)

Luo, Yaping; van den Brand, M.G.J.

2016-01-01

Context:In the safety domain, safety assessment is used to show that safety-critical systems meet the required safety objectives. This process is also referred to as safety assurance and certification. During this procedure, safety standards are used as development guidelines to keep the risk at an

Correlation between safety climate and contractor safety assessment programs in construction.

Science.gov (United States)

Sparer, Emily H; Murphy, Lauren A; Taylor, Kathryn M; Dennerlein, Jack T

2013-12-01

Contractor safety assessment programs (CSAPs) measure safety performance by integrating multiple data sources together; however, the relationship between these measures of safety performance and safety climate within the construction industry is unknown. Four hundred and one construction workers employed by 68 companies on 26 sites and 11 safety managers employed by 11 companies completed brief surveys containing a nine-item safety climate scale developed for the construction industry. CSAP scores from ConstructSecure, Inc., an online CSAP database, classified these 68 companies as high or low scorers, with the median score of the sample population as the threshold. Spearman rank correlations evaluated the association between the CSAP score and the safety climate score at the individual level, as well as with various grouping methodologies. In addition, Spearman correlations evaluated the comparison between manager-assessed safety climate and worker-assessed safety climate. There were no statistically significant differences between safety climate scores reported by workers in the high and low CSAP groups. There were, at best, weak correlations between workers' safety climate scores and the company CSAP scores, with marginal statistical significance with two groupings of the data. There were also no significant differences between the manager-assessed safety climate and the worker-assessed safety climate scores. A CSAP safety performance score does not appear to capture safety climate, as measured in this study. The nature of safety climate in construction is complex, which may be reflective of the challenges in measuring safety climate within this industry. Am. J. Ind. Med. 56:1463-1472, 2013. © 2013 Wiley Periodicals, Inc. © 2013 Wiley Periodicals, Inc.

High burn-up plutonium isotopic compositions recommended for use in shielding analysis

International Nuclear Information System (INIS)

Zimmerman, M.G.

1977-06-01

Isotopic compositions for plutonium generated and recycled in LWR's were estimated for use in shielding calculations. The values were obtained by averaging isotopic values from many sources in the literature. These isotopic values should provide the basis for a reasonable prediction of exposure rates from the range of LWR fuel expected in the future. The isotopic compositions given are meant to be used for shielding calculations, and the values are not necessarily applicable to other forms of analysis, such as inventory assessment or criticality safety. 11 tables, 2 figs

Safety assessment principles for nuclear plants

International Nuclear Information System (INIS)

1992-01-01

The present Safety Assessment Principles result from the revision of those which were drawn up following a recommendation arising from the Sizewell-B enquiry. The principles presented here relate only to nuclear safety; there is a section on risks from normal operation and accident conditions and the standards against which those risks are assessed. A major part of the document deals with the principles that cover the design of nuclear plants. The revised Safety assessment principles are aimed primarily at the safety assessment of new nuclear plants but they will also be used in assessing existing plants. (UK)

Development of safety related technology and infrastructure for safety assessment

International Nuclear Information System (INIS)

Venkat Raj, V.

1997-01-01

Development and optimum utilisation of any technology calls for the building up of the necessary infrastructure and backup facilities. This is particularly true for a developing country like India and more so for an advanced technology like nuclear technology. Right from the inception of its nuclear power programme, the Indian approach has been to develop adequate infrastructure in various areas such as design, construction, manufacture, installation, commissioning and safety assessment of nuclear plants. This paper deals with the development of safety related technology and the relevant infrastructure for safety assessment. A number of computer codes for safety assessment have been developed or adapted in the areas of thermal hydraulics, structural dynamics etc. These codes have undergone extensive validation through data generated in the experimental facilities set up in India as well as participation in international standard problem exercises. Side by side with the development of the tools for safety assessment, the development of safety related technology was also given equal importance. Many of the technologies required for the inspection, ageing assessment and estimation of the residual life of various components and equipment, particularly those having a bearing on safety, were developed. This paper highlights, briefly, the work carried out in some of the areas mentioned above. (author)

Thinking of the safety assessment of HLW disposal

International Nuclear Information System (INIS)

Li Honghui; Zhao Shuaiwei; Liu Jianqin; Liu Wei; Wan Lei; Yang Zhongtian; An Hongxiang; Sun Qinghong

2014-01-01

The function and the research methods of safety assessment are discussed. Two methods about safety assessment and the requirement of safety assessment are introduced. The key parameters and influence factors in nuclide transport of safety assessment are specialized. The works will be done on safety assessment is discussed which will give some suggests for the development of safety assessment. (authors)

ALARP considerations in criticality safety assessments

International Nuclear Information System (INIS)

Bowden, Russell L.; Barnes, Andrew; Thorne, Peter R.; Venner, Jack

2003-01-01

Demonstrating that the risk to the public and workers is As Low As Reasonably Practicable (ALARP) is a fundamental requirement of safety cases for nuclear facilities in the United Kingdom. This is embodied in the Safety Assessment Principles (SAPs) published by the Regulator, the essence of which is incorporated within the safety assessment processes of the various nuclear site licensees. The concept of ALARP within criticality safety assessments has taken some time to establish in the United Kingdom. In principle, the licensee is obliged to search for a deterministic criticality safety solution, such as safe geometry vessels and passive control features, rather than placing reliance on active measurement devices and plant administrative controls. This paper presents a consideration of some ALARP issues in relation to the development of criticality safety cases. The paper utilises some idealised examples covering a range of issues facing the criticality safety assessor, including new plant design, operational plant and decommissioning activities. These examples are used to outline the elements of the criticality safety cases and present a discussion of ALARP in the context of criticality safety assessments. (author)

Safety culture assessment developed by JANTI

International Nuclear Information System (INIS)

Hamada, Jun

2009-01-01

Japan's JCO accident in September 1999 provided a real-life example of what can happen when insufficient attention is paid to safety culture. This accident brought to light the importance of safety culture and reinforced the movement to foster a safety culture. Despite this, accidents and inappropriate conduct have continued to occur. Therefore, there is a strong demand to instill a safety culture throughout the nuclear power industry. In this context, Japan's nuclear power regulator, the Nuclear and Industrial Safety Agency (NISA), decided to include in its safety inspections assessments of the safety culture found in power utilities' routine safety operations to get signs of deterioration in the organizational climate. In 2007, NISA constructed guidelines for their inspectors to carry out these assessments. At the same time, utilities have embarked on their own independent safety culture initiatives, such as revising their technical specifications and building effective PDCA cycle to promote safety culture. In concert with these developments, JANTI has also instituted safety culture assessments. (author)

Rad waste disposal safety analysis / Integrated safety assessment of a waste repository

International Nuclear Information System (INIS)

Jeong, Jongtae; Choi, Jongwon; Kang, Chulhyung

2012-04-01

We developed CYPRUS+and adopted PID and RES method for the development of scenario. Safety performance assessment program was developed using GoldSim for the safety assessment of disposal system for the disposal of spnet fuels and wastes resulting from the pyrpoprocessing. Biosphere model was developed and verified in cooperation with JAEA. The capability to evaluate post-closure performance and safety was added to the previously developed program. And, nuclide migration and release to the biosphere considering site characteristics was evaluated by using deterministic and probabilistic approach. Operational safety assessment for drop, fire, and earthquake was also statistically evaluated considering well-established input parameter distribution. Conservative assessment showed that dose rate is below the limit value of low- and intermediate-level repository. Gas generation mechanism within engineered barrier was defined and its influence on safety was evaluated. We made probabilistic safety assessment by obtaining the probability distribution functions of important input variables and also made a sensitivity analysis. The maximum annual dose rate was shown to be below the safety limit value of 10 mSv/yr. The structure and element of safety case was developed to increase reliability of safety assessment methodology for a deep geological repository. Finally, milestone for safety case development and implementation strategy for each safety case element was also proposed

Self-assessment of application of the Code of Conduct on the safety of research reactors - Mexico

International Nuclear Information System (INIS)

Mamani-Alegria, Y.R.; Salgado-Gonzalez, J.R.; Miranda-Aldaco, J.

2009-01-01

In Mexico, the nuclear regulatory body is the National Commission on Nuclear Safety and Safeguards (CNSNS), and there is one research reactor, a TRIGA MARK III, operated by the National Institute for Nuclear Research (ININ). The main aspects of the Self-assessment of application of The Code of Conduct on the Safety of Research Reactor are given for the case of the TRIGA reactor. Furthermore, in this paper we give a brief description of the legal framework of the licensing process, for nuclear activities in a research reactor, there are also highlights of the major reactor features, the uses of the reactor for isotope production, the management and verification of safety, the radiation protection management program, the emergency planning and the training and qualification of the operation personnel. (author)

The Safety Case and Safety Assessment for the Disposal of Radioactive Waste

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-09-15

This Safety Guide provides guidance and recommendations on meeting the safety requirements in respect of the safety case and supporting safety assessment for the disposal of radioactive waste. The safety case and supporting safety assessment provide the basis for demonstration of safety and for licensing of radioactive waste disposal facilities and assist and guide decisions on siting, design and operations. The safety case is also the main basis on which dialogue with interested parties is conducted and on which confidence in the safety of the disposal facility is developed. This Safety Guide is relevant for operating organizations preparing the safety case as well as for the regulatory body responsible for developing the regulations and regulatory guidance that determine the basis and scope of the safety case. Contents: 1. Introduction; 2. Demonstrating the safety of radioactive waste disposal; 3. Safety principles and safety requirements; 4. The safety case for disposal of radioactive waste; 5. Radiological impact assessment for the period after closure; 6. Specific issues; 7. Documentation and use of the safety case; 8. Regulatory review process.

Status of High Flux Isotope Reactor (HFIR) post-restart safety analysis and documentation upgrades

International Nuclear Information System (INIS)

Cook, D.H.; Radcliff, T.D.; Rothrock, R.B.; Schreiber, R.E.

1990-01-01

The High Flux Isotope Reactor (HFIR), an experimental reactor located at the Oak Ridge National Laboratory (ORNL) and operated for the US Department of Energy by Martin Marietta Energy Systems, was shut down in November, 1986 after the discovery of unexpected neutron embrittlement of the reactor vessel. The reactor was restarted in April, 1989, following an extensive review by DOE and ORNL of the HFIR design, safety, operation, maintenance and management, and the implementation of several upgrades to HFIR safety-related hardware, analyses, documents and procedures. This included establishing new operating conditions to provide added margin against pressure vessel failure, as well as the addition, or upgrading, of specific safety-related hardware. This paper summarizes the status of some of the follow-on (post-restart) activities which are currently in progress, and which will result in a comprehensive set of safety analyses and documentation for the HFIR, comparable with current practice in commercial nuclear power plants. 8 refs

Safety assessment for facilities and activities. General safety requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF 6 ; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2010-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation. The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are installed; (i

Safety Assessment for Facilities and Activities. General Safety Requirements. Pt. 4

International Nuclear Information System (INIS)

2009-01-01

The Safety Fundamentals publication, Fundamental Safety Principles, establishes principles for ensuring the protection of workers, the public and the environment, now and in the future, from harmful effects of ionizing radiation.? read more The objective of this Safety Requirements publication is to establish the generally applicable requirements to be fulfilled in safety assessment for facilities and activities, with special attention paid to defence in depth, quantitative analyses and the application of a graded approach to the ranges of facilities and of activities that are addressed. The publication also addresses the independent verification of the safety assessment that needs to be carried out by the originators and users of the safety assessment. This publication is intended to provide a consistent and coherent basis for safety assessment across all facilities and activities, which will facilitate the transfer of good practices between organizations conducting safety assessments and will assist in enhancing the confidence of all interested parties that an adequate level of safety has been achieved for facilities and activities. The requirements, which are derived from the Fundamental Safety Principles, relate to any human activity that may cause people to be exposed to radiation risks arising from facilities and activities, as follows: Facilities includes: (a) Nuclear power plants; (b) Other reactors (such as research reactors and critical assemblies); (c) Enrichment facilities and fuel fabrication facilities; (d) Conversion facilities used to generate UF6; (e) Storage and reprocessing plants for irradiated fuel; (f) Facilities for radioactive waste management where radioactive waste is treated, conditioned, stored or disposed of; (g) Any other places where radioactive materials are produced, processed, used, handled or stored; (h) Irradiation facilities for medical, industrial, research and other purposes, and any places where radiation generators are

Safety Culture Monitoring: How to Assess Safety Culture in Real Time?

International Nuclear Information System (INIS)

Zronek, B.; Maryska, J.; Treslova, L.

2016-01-01

Do you know what is current level of safety culture in your company? Are you able to follow trend changes? Do you know what your recent issues are? Since safety culture is understood as vital part of nuclear industry daily life, it is crucial to know what the current level is. It is common to perform safety culture survey or ad hoc assessment. This contribution shares Temelin NPP, CEZ approach how to assess safety culture level permanently. Using behavioral related outputs of gap solving system, observation program, dedicated surveys, regulatory assessment, etc., allows creating real time safety culture monitoring without the need to perform any other activities. (author)

Regulatory review of safety cases and safety assessments - associated challenges

International Nuclear Information System (INIS)

Bennett, D.G.; Ben Belfadhel, M.; Metcalf, P.E.

2006-01-01

Regulatory reviews of safety cases and safety assessments are essential for credible decision making on the licensing or authorization of radioactive waste disposal facilities. Regulatory review also plays an important role in developing the safety case and in establishing stakeholders' confidence in the safety of the facility. Reviews of safety cases for radioactive waste disposal facilities need to be conducted by suitably qualified and experienced staff, following systematic and well planned review processes. Regulatory reviews should be sufficiently comprehensive in their coverage of issues potentially affecting the safety of the disposal system, and should assess the safety case against clearly established criteria. The conclusions drawn from a regulatory review, and the rationale for them should be reproducible and documented in a transparent and traceable way. Many challenges are faced when conducting regulatory reviews of safety cases. Some of these relate to issues of project and programme management, and resources, while others derive from the inherent difficulties of assessing the potential long term future behaviour of engineered and environmental systems. The paper describes approaches to the conduct of regulatory reviews and discusses some of the challenges faced. (author)

Intermediate probabilistic safety assessment approach for safety critical digital systems

International Nuclear Information System (INIS)

Taeyong, Sung; Hyun Gook, Kang

2001-01-01

Even though the conventional probabilistic safety assessment methods are immature for applying to microprocessor-based digital systems, practical needs force to apply it. In the Korea, UCN 5 and 6 units are being constructed and Korean Next Generation Reactor is being designed using the digital instrumentation and control equipment for the safety related functions. Korean regulatory body requires probabilistic safety assessment. This paper analyzes the difficulties on the assessment of digital systems and suggests an intermediate framework for evaluating their safety using fault tree models. The framework deals with several important characteristics of digital systems including software modules and fault-tolerant features. We expect that the analysis result will provide valuable design feedback. (authors)

Safety assessments for potential exposures

International Nuclear Information System (INIS)

Dunn, D.I.

2012-04-01

Safety Assessment of potential exposures have been carried out in major practices, namely: industrial radiography, gamma irradiators and electron accelerators used in industry and research, and radiotherapy. This paper focuses on reviewing safety assessment methodologies and using developed software to analyse radiological accidents, also review, and discuss these past accidents.The primary objective of the assessment is to assess the adequacy of planned or existing measures for protection and safety and to identify any additional measures that should be put in place. As such, both routine use of the source and the probability and magnitude of potential exposures arising from accidents or incidents should be considered. Where the assessment indicates that there is a realistic possibility of an accident affecting workers or members of the public or having consequences for the environment, the registrant or licensee should prepare a suitable emergency plan. A safety assessment for normal operation addresses all the conditions under which the radiation source operates as expected, including all phases of the lifetime of the source. Due account needs to be taken of the different factors and conditions that will apply during non-operational phases, such as installation, commissioning and maintenance. (author)

Development of a Safety Assessment Information System for the Management of Periodic Safety Assessment Activities

International Nuclear Information System (INIS)

Song, Tae Young

2007-01-01

At present, the 10-year Periodic Safety Review(PSR) has been performing to confirm all the aspects of safety issues for all the operating plants in compliance with domestic nuclear law of article 23, subarticle 3. For each plant, in addition, Probabilistic Safety Assessment(PSA) and Severe Accident Management Guideline(SAMG) are being implemented and revised periodically to reflect the latest safety level according to principle fulfillment of severe accident policy statement. The assessment reports, as one of outcomes from these activities, are submitted into and reviewed by domestic regulatory body. During reviewing (in-office duty) and licensing (regulatory duty) process, a large number of outcomes of which most are the formal technical reports and licensing materials, are inevitably produced. Moreover, repeated review process over the plants can make them accumulated and produce a variety of documents additionally. This circumstance motivates to develop effective tool or system for the management of these reports and related technical documents for the future use in licensing process and for subsequent plant assessments. This paper presents the development status of Safety Assessment Information System(SAIS) which manages safety-related documents of PSR, PSA and SAMG for practical use for experienced engineers in charge of these areas

Development of a Safety Assessment Information System for the Management of Periodic Safety Assessment Activities

Energy Technology Data Exchange (ETDEWEB)

Song, Tae Young [Nuclear Engineering and Technology Institute, Daejeon (Korea, Republic of)

2007-07-01

At present, the 10-year Periodic Safety Review(PSR) has been performing to confirm all the aspects of safety issues for all the operating plants in compliance with domestic nuclear law of article 23, subarticle 3. For each plant, in addition, Probabilistic Safety Assessment(PSA) and Severe Accident Management Guideline(SAMG) are being implemented and revised periodically to reflect the latest safety level according to principle fulfillment of severe accident policy statement. The assessment reports, as one of outcomes from these activities, are submitted into and reviewed by domestic regulatory body. During reviewing (in-office duty) and licensing (regulatory duty) process, a large number of outcomes of which most are the formal technical reports and licensing materials, are inevitably produced. Moreover, repeated review process over the plants can make them accumulated and produce a variety of documents additionally. This circumstance motivates to develop effective tool or system for the management of these reports and related technical documents for the future use in licensing process and for subsequent plant assessments. This paper presents the development status of Safety Assessment Information System(SAIS) which manages safety-related documents of PSR, PSA and SAMG for practical use for experienced engineers in charge of these areas.

Safety assessment for spent fuel storage facilities

International Nuclear Information System (INIS)

1994-01-01

This Safety Practice has been prepared as part of the IAEA's programme on the safety assessment of interim spent fuel storage facilities which are not an integral part of an operating nuclear power plant. This report provides general guidance on the safety assessment process, discussing both deterministic and probabilistic assessment methods. It describes the safety assessment process for normal operation and anticipated operational occurrences and also related to accident conditions. 10 refs, 2 tabs

Environmental Development Plan for advanced isotope separation

International Nuclear Information System (INIS)

1979-05-01

This EDP identifies the planning and management requirements and schedules needed to evaluate and assess the environmental, health, and safety aspects of the Advanced Isotope Separation (AIS) program. Current AIS processes include the molecular and atomic vapor laser processes and the plasma process. This document covers the technology program, environmental concerns and requirements, and environmental strategy

Radiation safety aspects in application of isotopes for industrial radiography in Bangladesh

Energy Technology Data Exchange (ETDEWEB)

Bakht, D. [Titas Gas Transmission and Distribution Company, Dhaka (Bangladesh)

1997-10-01

Industrial Radiography arose out of the widespread applications of X-rays pioneered by Roentgen about 100 years back. It is routinely used in studying the integrity of structural materials and like most countries in the world, its use in Bangladesh is increasing at a faster rate. This is because Bangladesh is a developing country of 3rd world and in the backdrop of agrarian poverty ridden economy, its population may exceed 125 millions by 2000 AD, leaving some 12 millions people unemployed. To support them, therefore, immense activities are activated in different sectors. Accordingly, increasing importance on NDT is given and in most cases particular application of Gamma radiography is preferred using Iridium Isotope Ir-192. Consequently the points of implications of isotopes are in Open Field and Inservice Inspection Radiography, Handling of Radiation Emergencies, Safe Transport of Radioactive Materials and Hazardous Effects and Risk of Ionizing Radiation, etc. Accordingly over exposure of Ir-192 Radionuclides, Accidents and Unusual Occurrences: Case Studies, Training Courses on Safety and Regulation of Sealed Sources, Licenses for Radiography Operation including Safe Disposal of Isotopes are the salient issues to be viewed in appropriate perspectives. The role played by Bangladesh Atomic Energy Commission and Bangladesh Society for NDT in collaboration with other members of the international committee for NDT are furthering the safe industrialization process

Radiation safety aspects in application of isotopes for industrial radiography in Bangladesh

International Nuclear Information System (INIS)

Bakht, D.

1997-01-01

Industrial Radiography arose out of the widespread applications of X-rays pioneered by Roentgen about 100 years back. It is routinely used in studying the integrity of structural materials and like most countries in the world, its use in Bangladesh is increasing at a faster rate. This is because Bangladesh is a developing country of 3rd world and in the backdrop of agrarian poverty ridden economy, its population may exceed 125 millions by 2000 AD, leaving some 12 millions people unemployed. To support them, therefore, immense activities are activated in different sectors. Accordingly, increasing importance on NDT is given and in most cases particular application of Gamma radiography is preferred using Iridium Isotope Ir-192. Consequently the points of implications of isotopes are in Open Field and Inservice Inspection Radiography, Handling of Radiation Emergencies, Safe Transport of Radioactive Materials and Hazardous Effects and Risk of Ionizing Radiation, etc. Accordingly over exposure of Ir-192 Radionuclides, Accidents and Unusual Occurrences: Case Studies, Training Courses on Safety and Regulation of Sealed Sources, Licenses for Radiography Operation including Safe Disposal of Isotopes are the salient issues to be viewed in appropriate perspectives. The role played by Bangladesh Atomic Energy Commission and Bangladesh Society for NDT in collaboration with other members of the international committee for NDT are furthering the safe industrialization process

Consideration of aging in probabilistic safety assessment

International Nuclear Information System (INIS)

Titina, B.; Cepin, M.

2007-01-01

Probabilistic safety assessment is a standardised tool for assessment of safety of nuclear power plants. It is a complement to the safety analyses. Standard probabilistic models of safety equipment assume component failure rate as a constant. Ageing of systems, structures and components can theoretically be included in new age-dependent probabilistic safety assessment, which generally causes the failure rate to be a function of age. New age-dependent probabilistic safety assessment models, which offer explicit calculation of the ageing effects, are developed. Several groups of components are considered which require their unique models: e.g. operating components e.g. stand-by components. The developed models on the component level are inserted into the models of the probabilistic safety assessment in order that the ageing effects are evaluated for complete systems. The preliminary results show that the lack of necessary data for consideration of ageing causes highly uncertain models and consequently the results. (author)

A Methodology for Safety Culture Impact Assessment

Energy Technology Data Exchange (ETDEWEB)

Han, Kiyoon; Jae, Moosung [Hanyang Univ., Seoul (Korea, Republic of)

2014-05-15

The purpose of this study is to develop methodology for assessing safety culture impact on nuclear power plants. A new methodology for assessing safety culture impact index has been developed and applied for the reference nuclear power plants. The developed SCII model might contribute to comparing the level of safety culture among nuclear power plants as well as to improving the safety of nuclear power plants. Safety culture is defined to be fundamental attitudes and behaviors of the plant staff which demonstrate that nuclear safety is the most important consideration in all activities conducted in nuclear power operation. Through several accidents of nuclear power plant including the Fukusima Daiichi in 2011 and Chernovyl accidents in 1986, the safety of nuclear power plant is emerging into a matter of interest. From the accident review report, it can be easily found out that safety culture is important and one of dominant contributors to accidents. However, the impact methodology for assessing safety culture has not been established analytically yet. It is difficult to develop the methodology for assessing safety culture impact quantitatively.

A Methodology for Safety Culture Impact Assessment

International Nuclear Information System (INIS)

Han, Kiyoon; Jae, Moosung

2014-01-01

The purpose of this study is to develop methodology for assessing safety culture impact on nuclear power plants. A new methodology for assessing safety culture impact index has been developed and applied for the reference nuclear power plants. The developed SCII model might contribute to comparing the level of safety culture among nuclear power plants as well as to improving the safety of nuclear power plants. Safety culture is defined to be fundamental attitudes and behaviors of the plant staff which demonstrate that nuclear safety is the most important consideration in all activities conducted in nuclear power operation. Through several accidents of nuclear power plant including the Fukusima Daiichi in 2011 and Chernovyl accidents in 1986, the safety of nuclear power plant is emerging into a matter of interest. From the accident review report, it can be easily found out that safety culture is important and one of dominant contributors to accidents. However, the impact methodology for assessing safety culture has not been established analytically yet. It is difficult to develop the methodology for assessing safety culture impact quantitatively

Regulatory review of safety cases and safety assessments for near surface

International Nuclear Information System (INIS)

Nys, V.

2003-01-01

The activities of the ASAM Regulatory Review Working Group are presented. Regulatory review of the safety assessment is made. It includes the regulatory review of post-closure safety assessment; safety case development and confidence building. The ISAM methodology is reviewed and SA system description is presented. Recommendations on the review process management are given

Safety Auditing and Assessments

Science.gov (United States)

Goodin, James Ronald (Ronnie)

2005-01-01

Safety professionals typically do not engage in audits and independent assessments with the vigor as do our quality brethren. Taking advantage of industry and government experience conducting value added Independent Assessments or Audits benefits a safety program. Most other organizations simply call this process "internal audits." Sources of audit training are presented and compared. A relation of logic between audit techniques and mishap investigation is discussed. An example of an audit process is offered. Shortcomings and pitfalls of auditing are covered.

A METHOD TO IMPROVE DOSE ASSESSMENT BY RECONSTRUCTION OF THE COMPLETE ISOTOPES INVENTORY.

Science.gov (United States)

Bonin, Alice; Tsilanizara, Aimé

2017-06-01

Radiation shielding assessments may underestimate the expected dose if some isotopes at trace level are not considered in the isotopes inventory of the shielded radioactive materials. Indeed, information about traces is not often available. Nevertheless, the activation of some minor isotopic traces may significantly contribute to the dose build-up. This paper presents a new method (Isotopes Inventory Reconstruction-IIR) estimating the concentration of the minor isotopes in the irradiated material at the beginning of the cooling period. The method requires the solution of the inverse problem describing the irradiated material's decay. In a mixture of an irradiated uranium-plutonium oxide shielded by a set-up made of stainless-steel, porous polyethylene plaster and lead methyl methacrylate, the comparison between different methods proves that the IIR-method allows better assessment of the dose than other approximate methods. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Confidence building in safety assessments

International Nuclear Information System (INIS)

Grundfelt, Bertil

1999-01-01

Future generations should be adequately protected from damage caused by the present disposal of radioactive waste. This presentation discusses the core of safety and performance assessment: The demonstration and building of confidence that the disposal system meets the safety requirements stipulated by society. The major difficulty is to deal with risks in the very long time perspective of the thousands of years during which the waste is hazardous. Concern about these problems has stimulated the development of the safety assessment discipline. The presentation concentrates on two of the elements of safety assessment: (1) Uncertainty and sensitivity analysis, and (2) validation and review. Uncertainty is associated both with respect to what is the proper conceptual model and with respect to parameter values for a given model. A special kind of uncertainty derives from the variation of a property in space. Geostatistics is one approach to handling spatial variability. The simplest way of doing a sensitivity analysis is to offset the model parameters one by one and observe how the model output changes. The validity of the models and data used to make predictions is central to the credibility of safety assessments for radioactive waste repositories. There are several definitions of model validation. The presentation discusses it as a process and highlights some aspects of validation methodologies

Food certification based on isotopic analysis, according to the European standards

International Nuclear Information System (INIS)

Costinel, Diana; Ionete, Roxana Elena; Vremera, Raluca; Stanciu, Vasile; Iordache, Andreea

2007-01-01

Full text: Under current EU research projects, several public research institutions, universities and private companies are collaborating to develop new methods of evidencing food adulteration and consequently assessing food safety. The use of mass spectrometry (MS) to determine the ratio of stable isotopes in bio-molecules now provides the means to prove the natural origin of a wide variety of foodstuffs - and therefore, to identify the fraud and consequently to reject the improper products or certify the food quality. Isotope analysis has been officially adopted by the EU as a means of controlling adulteration of some food stuffs. A network of research organizations developed the use of isotopic analysis to support training and technology transfer to encourage uptake of the technique. There were also developed proficiency-testing schemes to ensure the correct use of isotopic techniques in national testing laboratories. In addition, ensuring the food quality and safety is a requirement, which must be fulfilled for the integration in EU. The present paper emphasizes the isotopic analysis for D/H, 18 O/ 16 O, 13 C/ 12 C from food (honey, juice, wines) using a new generation Isotope Ratio MS, Finnigan Delta V Plus, coupled to a three flexible continuous flow preparation device (GasBench II, TC Elemental Analyser and GC-C/TC). (authors)

Application of Isotope Techniques for Assessing Nutrient Dynamics in River Basins

International Nuclear Information System (INIS)

2013-05-01

Nutrients are necessary for the growth and survival of animals, plants and other organisms. However, industrial, agricultural and urban development has dramatically increased nutrient levels in river systems, including nitrogen and phosphorus containing substances, degrading water quality, causing acidification and eutrophication and affecting aquatic ecosystems. Nutrient assessment and management in river systems has been an important part of water resource management for the past few decades, but the provision of appropriate and effective nutrient assessment and management continues to be a challenge for water resource managers and policy makers. Difficulties in assessment and management are due in part to the fact that nutrients in rivers may originate from a variety of sources, take numerous pathways and transform into other substances. This publication presents the application of isotope techniques as a powerful tool for evaluating the sources, pathways, transformation, and fate of nutrients in river systems, focusing on nitrogen, phosphorus and carbon containing substances. Eleven researchers using various isotope techniques for different aspects of nutrient studies and two IAEA officers met in a technical meeting and discussed a publication that could assist water resource managers in dealing with nutrient assessment and management issues in river systems. These researchers also recognized the need for careful consideration in selecting appropriate isotope techniques in view of not only technical, but also financial, human resources and logistical capabilities, among others. These contributors are listed as major authors in the later pages of this document. This publication aims at serving water resource managers as a guidebook on the application of isotope techniques in nutrient assessment and management, but it is also expected to be of practical aid for other interested and concerned individuals and organization.

Application of Isotope Techniques for Assessing Nutrient Dynamics in River Basins

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-05-15

Nutrients are necessary for the growth and survival of animals, plants and other organisms. However, industrial, agricultural and urban development has dramatically increased nutrient levels in river systems, including nitrogen and phosphorus containing substances, degrading water quality, causing acidification and eutrophication and affecting aquatic ecosystems. Nutrient assessment and management in river systems has been an important part of water resource management for the past few decades, but the provision of appropriate and effective nutrient assessment and management continues to be a challenge for water resource managers and policy makers. Difficulties in assessment and management are due in part to the fact that nutrients in rivers may originate from a variety of sources, take numerous pathways and transform into other substances. This publication presents the application of isotope techniques as a powerful tool for evaluating the sources, pathways, transformation, and fate of nutrients in river systems, focusing on nitrogen, phosphorus and carbon containing substances. Eleven researchers using various isotope techniques for different aspects of nutrient studies and two IAEA officers met in a technical meeting and discussed a publication that could assist water resource managers in dealing with nutrient assessment and management issues in river systems. These researchers also recognized the need for careful consideration in selecting appropriate isotope techniques in view of not only technical, but also financial, human resources and logistical capabilities, among others. These contributors are listed as major authors in the later pages of this document. This publication aims at serving water resource managers as a guidebook on the application of isotope techniques in nutrient assessment and management, but it is also expected to be of practical aid for other interested and concerned individuals and organization.

Radiological risk assessment of isotope laboratories according to the requirements of the radiation protection ordinance and the protective labour legislation

International Nuclear Information System (INIS)

Stuerm, R.P.; Kuster, M.; Traub, K.

2001-01-01

According to the Swiss Radiation Safety Ordinance the supervising authority may require a safety report from the operator of a radioactive laboratory (Art.95) and establish the methodology of the risk analysis. Isotope laboratories of the chemical industry are supervised by Swiss accident insurance agency (SUVA). In that respect SUVA safeguards both radiation protection issues and general protection of the workers and established guide lines in order to assess conventional risks in industrial premises. In these conventional analysis the working process is analysed according to its possible detriment (death, severe invalidity, slight invalidity, injury with absence, injury without absence) and the probability of occurrence (frequent, seldom, rare, improbable, virtually impossible). According to this the risks are categorised in a matrix as 'high', 'medium' and 'low'. SUVA requested such a risk analysis for two isotope laboratories of B type in Basel in which on the one hand the hazard to the workers on the other hand to the public should be analysed and radiologically assessed. It was proposed to use a methodology established in workers safety and the insurance section. This required a comparison of risks of radiation doses in mSv to the consequences of conventional working accidents (death, invalidity) and the risk perception of the public and politicians. In this paper this risk matrix derived in discussions among the supervising body, the company management, the laboratory head and workers is described. In the opinion of the authors such a comparison between radiological and conventional risks has not been performed up to now and the results obtained here are open to discussion. (orig.) [de

Effect of fissile isotope burnup on criticality safety for stored disintegrated fuel rods

International Nuclear Information System (INIS)

Heaberlin, S.W.; Selby, G.P.

1978-09-01

If the fuel rods were to disintegrate and water added, a criticality could occur in a 13-in. PWR canister with fresh fuel enriched to 3.5 wt % 235 U. The question is, ''If credit could be taken for burnup, could this indicate a subcritical condition.'' In attempting to answer this question, a series of calculations were performed. A set of isotopic concentrations were generated for 5,000, 10,000, 15,000, and 20,000 MWD/MTU burnup levels. Four reflector materials, water, concrete and two types of soil, were considered. Results indicate that allowing credit for fissile isotope burnup does not completely remove the concern for criticality safety in the event of rod disintegration. Reactivities which are ''subcritical'' (k/sub eff/ = 0.95) would not occur for three of the four reflector materials at even the 20,000 MWD/MTU burnup level in the 13-in. canister. The water reflected canister would achieve the k/sub eff/ = 0.95 level near 18,000 MWD/MTU. A smaller canister could be postulated. If a quarter inch gap is allowed, a Westinghouse 17 x 17 PWR assembly requires a 12 1 / 4 inch diameter canister. For such a canister with water reflection the ''subcritical'' (k/sub eff/ = 0.95) level would be reached near 15,000 MWD/MTU. The soil reflected canisters would reach this level between 18,000 and 19,000 MWD/MTU. Considering the difficulties in taking credit for burnup, such modest gains in apparent safety are not encouraging. This situation might be improved, however, if credit were also taken for neutron absorption by fission product poisons produced during burnup. It is strongly recommended that other approaches to a solution of the criticality safety problem be considered

Assessment of Stable Isotope Distribution in Complex Systems

Science.gov (United States)

He, Y.; Cao, X.; Wang, J.; Bao, H.

2017-12-01

Biomolecules in living organisms have the potential to approach chemical steady state and even apparent isotope equilibrium because enzymatic reactions are intrinsically reversible. If an apparent local equilibrium can be identified, enzymatic reversibility and its controlling factors may be quantified, which helps to understand complex biochemical processes. Earlier research on isotope fractionation tends to focus on specific process and compare mostly two different chemical species. Using linear regression, "Thermodynamic order", which refers to correlated δ13C and 13β values, has been proposed to be present among many biomolecules by Galimov et al. However, the concept "thermodynamic order" they proposed and the approach they used has been questioned. Here, we propose that the deviation of a complex system from its equilibrium state can be rigorously described as a graph problem as is applied in discrete mathematics. The deviation of isotope distribution from equilibrium state and apparent local isotope equilibrium among a subset of biomolecules can be assessed using an apparent fractionation difference matrix (|Δα|). Applying the |Δα| matrix analysis to earlier published data of amino acids, we show the existence of apparent local equilibrium among different amino acids in potato and a kind of green alga. The existence of apparent local equilibrium is in turn consistent with the notion that enzymatic reactions can be reversible even in living systems. The result also implies that previous emphasis on external carbon source intake may be misplaced when studying isotope distribution in physiology. In addition to the identification of local equilibrium among biomolecules, the difference matrix approach has the potential to explore chemical or isotope equilibrium state in extraterrestrial bodies, to distinguish living from non-living systems, and to classify living species. This approach will benefit from large numbers of systematic data and advanced pattern

Safety Management and Safety Culture Self Assessment of Kartini Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Syarip, S., E-mail: syarip@batan.go.id [Centre for Accelerator and Material Process Technology, National Nuclear Energy Agency (BATAN), Yogyakarta (Indonesia)

2014-10-15

The self-assessment of safety culture and safety management status of Kartini research reactor is a step to foster safety culture and management by identifying good practices and areas for improvement, and also to improve reactor safety in a whole. The method used in this assessment is based on questionnaires provided by the Forum for Nuclear Cooperation in Asia (FNCA), then reviewed by experts. Based on the assessment and evaluation results, it can be concluded that there were several good practices in maintaining the safety status of Kartini reactor such as: reactor operators and radiation protection workers were aware and knowledgeable of the safety standards and policies that apply to their operation, readily accept constructive criticism from their management and from the inspectors of regulatory body that address safety performance. As a proof, for the last four years the number of inspection/audit findings from Regulatory Body (BAPETEN) tended to decrease while the reactor utilization and its operating hour increased. On the other hands there were also some comments and recommendations for improvement of reactor safety culture, such as that there should be more frequent open dialogues between employees and managers, to grow and attain a mutual support to achieve safety goals. (author)

Determination of Safety Performance Grade of NPP Using Integrated Safety Performance Assessment (ISPA) Program

International Nuclear Information System (INIS)

Chung, Dae Wook

2011-01-01

Since the beginning of 2000, the safety regulation of nuclear power plant (NPP) has been challenged to be conducted more reasonable, effective and efficient way using risk and performance information. In the United States, USNRC established Reactor Oversight Process (ROP) in 2000 for improving the effectiveness of safety regulation of operating NPPs. The main idea of ROP is to classify the NPPs into 5 categories based on the results of safety performance assessment and to conduct graded regulatory programs according to categorization, which might be interpreted as 'Graded Regulation'. However, the classification of safety performance categories is highly comprehensive and sensitive process so that safety performance assessment program should be prepared in integrated, objective and quantitative manner. Furthermore, the results of assessment should characterize and categorize the actual level of safety performance of specific NPP, integrating all the substantial elements for assessing the safety performance. In consideration of particular regulatory environment in Korea, the integrated safety performance assessment (ISPA) program is being under development for the use in the determination of safety performance grade (SPG) of a NPP. The ISPA program consists of 6 individual assessment programs (4 quantitative and 2 qualitative) which cover the overall safety performance of NPP. Some of the assessment programs which are already implemented are used directly or modified for incorporating risk aspects. The others which are not existing regulatory programs are newly developed. Eventually, all the assessment results from individual assessment programs are produced and integrated to determine the safety performance grade of a specific NPP

Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

International Nuclear Information System (INIS)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-01-01

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design

Temperature and void reactivity coefficient calculations for the high flux isotope reactor safety analysis report

International Nuclear Information System (INIS)

Engle, W.W. Jr.; Williams, L.R.

1994-07-01

This report provides documentation of a series of calculations performed in 1991 in order to provide input for the High Flux Isotope Reactor Safety Analysis Report. In particular, temperature and void reactivity coefficients were calculated for beginning-of-life, end-of-life, and xenon equilibrium (29 h) conditions. Much of the data used to prepare the computer models for these calculations was derived from the original HFIR nuclear design study

The role of probabilistic safety assessment and probabilistic safety criteria in nuclear power plant safety

International Nuclear Information System (INIS)

1992-01-01

The purpose of this Safety Report is to provide guidelines on the role of probabilistic safety assessment (PSA) and a range of associated reference points, collectively referred to as probabilistic safety criteria (PSC), in nuclear safety. The application of this Safety Report and the supporting Safety Practice publication should help to ensure that PSA methodology is used appropriately to assess and enhance the safety of nuclear power plants. The guidelines are intended for use by nuclear power plant designers, operators and regulators. While these guidelines have been prepared with nuclear power plants in mind, the principles involved have wide application to other nuclear and non-nuclear facilities. In Section 2 of this Safety Report guidelines are established on the role PSA can play as part of an overall safety assurance programme. Section 3 summarizes guidelines for the conduct of PSAs, and in Section 4 a PSC framework is recommended and guidance is provided for the establishment of PSC values

The Application of Isotope Techniques in Nutrient Assessment and Management in Riverine Systems. Present and Future

Energy Technology Data Exchange (ETDEWEB)

Ito, M.; Newman, B. D. [International Atomic Energy Agency, Isotope Hydrology Section, Vienna (Austria); Hadwen, W. L. [Australian Rivers Institute, Griffith School of Environment, Griffith University - Nathan Campus, Brisbane, Queensland (Australia); Rogers, K. [National Isotope Center, GNS Science, Lower Hutt (New Zealand); Mayer, B. [Department of Geoscience, University of Calgary, Calgary, Alberta (Canada); Hein, T. [Wasser Cluster Lunz, Interuniversitary Center for Aquatic Research, Lunz-See, and University of Natural Resources and Applied Life Sciences, Institute of Hydrobiology and Aquatic Ecosystem Management, Vienna (Austria); Stellato, L. [Centre for Isotopic Research on Cultural and Environmental Heritage (CIRCE), Seconda Universita degli Studi di Napoli, Caserta (Italy); Ohte, N. [Graduate School of Agricultural and Life Sciences, University of Tokyo, Tokyo (Japan); Mclaughlin, K. [Southern California Coastal Water Research Project, Costa Mesa, California (United States)

2013-05-15

A variety of sources contribute to nutrients in rivers and nutrients may subsequently take various pathways and undergo different transformation processes. We first review representative types of isotopes and the roles of isotope techniques that have been or could be used for nutrient assessment and management. We then present technical, financial and logistical matters to be considered in selecting appropriate isotope techniques for nutrient assessment and management. Lastly we propose several approaches on the application of isotope techniques to make more effective the studies and management of nutrients in rivers in the near future. (author)

Reactor Safety Assessment System

International Nuclear Information System (INIS)

Sebo, D.E.; Bray, M.A.; King, M.A.

1987-01-01

The Reactor Safety Assessment System (RSAS) is an expert system under development for the United States Nuclear Regulatory Commission (USNRC). RSAS is designed for use at the USNRC Operations Center in the event of a serious incident at a licensed nuclear power plant. RSAS is a situation assessment expert system which uses plant parametric data to generate conclusions for use by the NRC Reactor Safety Team. RSAS uses multiple rule bases and plant specific setpoint files to be applicable to all licensed nuclear power plants in the United States. RSAS currently covers several generic reactor categories and multiple plants within each category

Reactor safety assessment system

International Nuclear Information System (INIS)

Sebo, D.E.; Bray, M.A.; King, M.A.

1987-01-01

The Reactor Safety Assessment System (RSAS) is an expert system under development for the United States Nuclear Regulatory Commission (USNRC). RSA is designed for use at the USNRC Operations Center in the event of a serious incident at a licensed nuclear power plant. RSAS is a situation assessment expert system which uses plant parametric data to generate conclusions for use by the NRC Reactor Safety Team. RSAS uses multiple rule bases and plant specific setpoint files to be applicable to all licensed nuclear power plants in the United States. RSAS currently covers several generic reactor categories and multiple plants within each category

Independent assessment for new nuclear reactor safety

Directory of Open Access Journals (Sweden)

D'Auria Francesco

2017-01-01

Full Text Available A rigorous framework for safety assessment is established in all countries where nuclear technology is used for the production of electricity. On the one side, industry, i.e. reactor designers, vendors and utilities perform safety analysis and demonstrate consistency between results of safety analyses and requirements. On the other side, regulatory authorities perform independent assessment of safety and confirm the acceptability of safety of individual reactor units. The process of comparing results from analyses by reactor utilities and regulators is very complex. The process is also highly dependent upon mandatory approaches pursued for the analysis and from very many details which required the knowledge of sensitive proprietary data (e.g. spacer designs. Furthermore, all data available for the design, construction and operation of reactors produced by the nuclear industry are available to regulators. Two areas for improving the process of safety assessment for individual Nuclear Power Plant Units are identified: New details introduced by industry are not always and systematically requested by regulators for the independent assessment; New analytical techniques and capabilities are not necessarily used in the analyses by regulators (and by the industry. The established concept of independent assessment constitutes the way for improving the process of safety assessment. This is possible, or is largely facilitated, by the recent availability of the so-called Best Estimate Plus Uncertainty approach.

Independent assessment for new nuclear reactor safety

International Nuclear Information System (INIS)

D'Auria, F.; Glaeser, H.; Debrecin, N.

2017-01-01

A rigorous framework for safety assessment is established in all countries where nuclear technology is used for the production of electricity. On one side, industry, i.e. reactor designers, vendors and utilities perform safety analysis and demonstrate consistency between results of safety analyses and requirements. On the other side, regulatory authorities perform independent assessment of safety and confirm the acceptability of safety of individual reactor units. The process of comparing results from analyses by reactor utilities and regulators is very complex. The process is also highly dependent upon mandatory approaches pursued for the analysis and from very many details which required the knowledge of sensitive proprietary data (e.g. spacer designs). Furthermore, all data available for the design, construction and operation of reactors produced by the nuclear industry are available to regulators. Two areas for improving the process of safety assessment for individual Nuclear Power Plant Units are identified: New details introduced by industry are not always and systematically requested by regulators for the independent assessment; New analytical techniques and capabilities are not necessarily used in the analyses by regulators (and by the industry). The established concept of independent assessment constitutes the way for improving the process of safety assessment. This is possible, or is largely facilitated, by the recent availability of the so-called Best Estimate Plus Uncertainty (BEPU) approach. (authors)

Hygienic assessment of radioactive iodine isotopes

International Nuclear Information System (INIS)

Vasilenko, I.Ya.

1987-01-01

Sources of radioactive iodine isotopes and their biological significance depending on the way of intake are discussed. The degree of food contamination by radioactive iodine as well as products, which serve as the source of its intake into the human body, and results of their processing are considered. The danger of radioactive iodine intake by different groups of population as well as thyroid irradiation effects are discussed. Description of activities, directed to the human body protection against radioactive iodine and assessment of these protection measures efficiency is presented

AGR core safety assessment methodologies

International Nuclear Information System (INIS)

McLachlan, N.; Reed, J.; Metcalfe, M.P.

1996-01-01

To demonstrate the safety of its gas-cooled graphite-moderated AGR reactors, nuclear safety assessments of the cores are based upon a methodology which demonstrates no component failures, geometrical stability of the structure and material properties bounded by a database. All AGRs continue to meet these three criteria. However, predictions of future core behaviour indicate that the safety case methodology will eventually need to be modified to deal with new phenomena. A new approach to the safety assessment of the cores is currently under development, which can take account of these factors while at the same time providing the same level of protection for the cores. This approach will be based on the functionality of the core: unhindered movement of control rods, continued adequate cooling of the fuel and the core, continued ability to charge and discharge fuel. (author). 5 figs

A new assessment method for demonstrating the sufficiency of the safety assessment and the safety margins of the geological disposal system

International Nuclear Information System (INIS)

Ohi, Takao; Kawasaki, Daisuke; Chiba, Tamotsu; Takase, Toshio; Hane, Koji

2013-01-01

A new method for demonstrating the sufficiency of the safety assessment and safety margins of the geological disposal system has been developed. The method is based on an existing comprehensive sensitivity analysis method and can systematically identify the successful conditions, under which the dose rate does not exceed specified safety criteria, using analytical solutions for nuclide migration and the results of a statistical analysis. The successful conditions were identified using three major variables. Furthermore, the successful conditions at the level of factors or parameters were obtained using relational equations between the variables and the factors or parameters making up these variables. In this study, the method was applied to the safety assessment of the geological disposal of transuranic waste in Japan. Based on the system response characteristics obtained from analytical solutions and on the successful conditions, the classification of the analytical conditions, the sufficiency of the safety assessment and the safety margins of the disposal system were then demonstrated. A new assessment procedure incorporating this method into the existing safety assessment approach is proposed in this study. Using this procedure, it is possible to conduct a series of safety assessment activities in a logical manner. (author)

Assessment of phyto-available cadmium in soils using isotopic methods

International Nuclear Information System (INIS)

Gerard, Emilie

2000-01-01

The quantification of phyto-available Cd in soils is necessary to determine the transfer risk of this toxic element to plants. Isotopic methods (isotopic exchange kinetics (IEK), isotopic dilution) were used to characterize the phyto-available Cd and, practically, to select chemical methods for determining available Cd to plants. Rye grass (Lolium perenne L.), lettuce (Lactuca saliva L.) and the Cd hyper-accumulator Thlaspi caerulescens J. Presl. and C. Presl. were selected as test plants because of their wide range of Cd uptake ability. The chosen soils had different pH and displayed a Cd-contamination gradient due the atmospheric deposition of industrial particles. In the acidic soil, plants had access to the same metal pool, the one that was isotopically exchangeable with Cd 2+ . This was also the case for rye grass on the calcareous Soils but there, lettuce and T. caerulescens accessed a bigger and non-isotopically exchangeable pool that accounted for 16 to 52 % of the plant available Cd. Most of the Cd was isotopically exchangeable in a short time in the acidic soil (87 % within 21 days). In the calcareous soils two pools were identified, one pool was isotopically exchangeable in a very short time, and the other one Was not exchangeable after 21 days (21 to 10 % of the total Cd). Actually, the quantities of labile cd in the industrial particles which had contaminated these soils were very small. IEK methods and the measurement of the isotopic composition of Cd 2+ in soil solutions allowed for the estimation of the phyto-available Cd in soils, but cannot he commonly used. Most of the chemical extractants studied such as CaCl 2 or DTP A are suitable to assess the phyto-available Cd. However, on calcareous soils, the choice of extractant needs to sometimes be modified in relation to the rate of Cd plant absorption. (author) [fr

Procedures for self-assessment of operational safety

International Nuclear Information System (INIS)

1997-08-01

Self-assessment processes have been continuously developed by nuclear organizations, including nuclear power plants. Currently, the nuclear industry and governmental organizations are showing an increasing interest in the implementation of this process as an effective way for improving safety performance. Self-assessment involves the use of different types of tools and mechanisms to assist the organizations in assessing their own safety performance against given standards. This helps to enhance the understanding of the need for improvements, the feeling of ownership in achieving them and and the safety culture as a whole. The concepts developed in this report present the basic approach to self-assessment taking into consideration experience gained during Operational Safety Review Team (OSART) missions, from organizations and utilities which have successfully implemented parts of a self-assessment programme and from meetings organized to discuss the subject

Uncertainty analysis in safety assessment

International Nuclear Information System (INIS)

Lemos, Francisco Luiz de; Sullivan, Terry

1997-01-01

Nuclear waste disposal is a very complex subject which requires the study of many different fields of science, like hydro geology, meteorology, geochemistry, etc. In addition, the waste disposal facilities are designed to last for a very long period of time. Both of these conditions make safety assessment projections filled with uncertainty. This paper addresses approaches for treatment of uncertainties in the safety assessment modeling due to the variability of data and some current approaches used to deal with this problem. (author)

NUMO's approach for long-term safety assessment - 59404

International Nuclear Information System (INIS)

Ebashi, Takeshi; Kaku, Kenichi; Ishiguro, Katsuhiko

2012-01-01

One of NUMO's policies for ensuring safety is staged and flexible project implementation and decision-making based on iterative confirmation of safety. The safety assessment takes the central role in multiple lines of reasoning and argumentation by providing a quantitative evaluation of long-term safety; a key aspect is uncertainty management. This paper presents NUMO's basic strategies for long-term safety assessment based on the above policy. NUMO's approach considering Japanese boundary conditions is demonstrated as a starting-point for evaluating the long-term safety of an actual site. In Japan, the Act on Final Disposal of Specified Radioactive Waste states that the siting process shall consist of three stages. The Nuclear Waste Management Organization of Japan (NUMO) is responsible for geological disposal of vitrified high-level waste and some types of TRU waste. NUMO has chosen to implement a volunteer approach to siting. NUMO decided to prepare the so-called 2010 technical report, which sets out three safety policies, one of which is staged project implementation and decision-making based on iterative confirmation of safety. Based on this policy, NUMO will gradually integrate relevant interdisciplinary knowledge to build a safety case when a formal volunteer application is received that would allow site investigations to be initiated. The safety assessment takes the central role in multiple lines of reasoning and argumentation by providing a quantitative evaluation of long-term safety; one of a key aspect is uncertainty management. This paper presents the basic strategies for NUMO's long-term safety assessment based on the above policy. In concrete terms, the common procedures involved in safety assessment are applied in a stepwise manner, based on integration of knowledge obtained from site investigations/evaluations and engineered measures. The results of the safety assessment are then reflected in the planning of site investigations and engineered

Probabilistic safety assessment

International Nuclear Information System (INIS)

Hoertner, H.; Schuetz, B.

1982-09-01

For the purpose of assessing applicability and informativeness on risk-analysis methods in licencing procedures under atomic law, the choice of instruments for probabilistic analysis, the problems in and experience gained in their application, and the discussion of safety goals with respect to such instruments are of paramount significance. Naturally, such a complex field can only be dealt with step by step, making contribution relative to specific problems. The report on hand shows the essentials of a 'stocktaking' of systems relability studies in the licencing procedure under atomic law and of an American report (NUREG-0739) on 'Quantitative Safety Goals'. (orig.) [de

Kilowatt isotope power system. Phase II plan. Volume V. Safety, quality assurance and reliability

International Nuclear Information System (INIS)

1978-01-01

The development of a Kilowatt Isotope Power System (KIPS) was begun in 1975 for the purpose of satisfying the power requirements of satellites in the 1980's. The KIPS is a 238 PuO 2 -fueled organic Rankine cycle turbine power system to provide a design output of 500 to 2000 W. Included in this volume are: launch and flight safety considerations; quality assurance techniques and procedures to be followed through system fabrication, assembly and inspection; and the reliability program made up of reliability prediction analysis, failure mode analysis and criticality analysis

A Methodology To Incorporate The Safety Culture Into Probabilistic Safety Assessments

Energy Technology Data Exchange (ETDEWEB)

Park, Sunghyun; Kim, Namyeong; Jae, Moosung [Hanyang University, Seoul (Korea, Republic of)

2015-10-15

In order to incorporate organizational factors into PSA, a methodology needs to be developed. Using the AHP to weigh organizational factors as well as the SLIM to rate those factors, a methodology is introduced in this study. The safety issues related to nuclear safety culture have occurred increasingly. The quantification tool has to be developed in order to include the organizational factor into Probabilistic Safety Assessments. In this study, the state-of-the-art for the organizational evaluation methodologies has been surveyed. This study includes the research for organizational factors, maintenance process, maintenance process analysis models, a quantitative methodology using Analytic Hierarchy Process, Success Likelihood Index Methodology. The purpose of this study is to develop a methodology to incorporate the safety culture into PSA for obtaining more objective risk than before. The organizational factor considered in nuclear safety culture might affect the potential risk of human error and hardware-failure. The safety culture impact index to monitor the plant safety culture can be assessed by applying the developed methodology into a nuclear power plant.

A Methodology To Incorporate The Safety Culture Into Probabilistic Safety Assessments

International Nuclear Information System (INIS)

Park, Sunghyun; Kim, Namyeong; Jae, Moosung

2015-01-01

In order to incorporate organizational factors into PSA, a methodology needs to be developed. Using the AHP to weigh organizational factors as well as the SLIM to rate those factors, a methodology is introduced in this study. The safety issues related to nuclear safety culture have occurred increasingly. The quantification tool has to be developed in order to include the organizational factor into Probabilistic Safety Assessments. In this study, the state-of-the-art for the organizational evaluation methodologies has been surveyed. This study includes the research for organizational factors, maintenance process, maintenance process analysis models, a quantitative methodology using Analytic Hierarchy Process, Success Likelihood Index Methodology. The purpose of this study is to develop a methodology to incorporate the safety culture into PSA for obtaining more objective risk than before. The organizational factor considered in nuclear safety culture might affect the potential risk of human error and hardware-failure. The safety culture impact index to monitor the plant safety culture can be assessed by applying the developed methodology into a nuclear power plant

Complementary safety assessments - Report by the French Nuclear Safety Authority

International Nuclear Information System (INIS)

2011-12-01

As an immediate consequence of the Fukushima accident, the French Authority of Nuclear Safety (ASN) launched a campaign of on-site inspections and asked operators (mainly EDF, AREVA and CEA) to make complementary assessments of the safety of the nuclear facilities they manage. The approach defined by ASN for the complementary safety assessments (CSA) is to study the behaviour of nuclear facilities in severe accidents situations caused by an off-site natural hazard according to accident scenarios exceeding the current baseline safety requirements. This approach can be broken into 2 phases: first conformity to current design and secondly an approach to the beyond design-basis scenarios built around the principle of defence in depth. 38 inspections were performed on issues linked to the causes of the Fukushima crisis. It appears that some sites have to reinforce the robustness of the heat sink. The CSA confirmed that the processes put into place at EDF to detect non-conformities were satisfactory. The complementary safety assessments demonstrated that the current seismic margins on the EDF nuclear reactors are satisfactory. With regard to flooding, the complementary safety assessments show that the complete reassessment carried out following the flooding of the Le Blayais nuclear power plant in 1999 offers the installations a high level of protection against the risk of flooding. Concerning the loss of electrical power supplies and the loss of cooling systems, the analysis of EDF's CSA reports showed that certain heat sink and electrical power supply loss scenarios can, if nothing is done, lead to core melt in just a few hours in the most unfavourable circumstances. As for nuclear facilities that are not power or experimental reactors, some difficulties have appeared to implement the CSA approach that was initially devised for reactors. Generally speaking, ASN considers that the safety of nuclear facilities must be made more robust to improbable risks which are not

Assessing connectivity of estuarine fishes based on stable isotope ratio analysis

Science.gov (United States)

Herzka, Sharon Z.

2005-07-01

Assessing connectivity is fundamental to understanding the population dynamics of fishes. I propose that isotopic analyses can greatly contribute to studies of connectivity in estuarine fishes due to the high diversity of isotopic signatures found among estuarine habitats and the fact that variations in isotopic composition at the base of a food web are reflected in the tissues of consumers. Isotopic analysis can be used for identifying nursery habitats and estimating their contribution to adult populations. If movement to a new habitat is accompanied by a shift to foods of distinct isotopic composition, recent immigrants and residents can be distinguished based on their isotopic ratios. Movement patterns thus can be reconstructed based on information obtained from individuals. A key consideration is the rate of isotopic turnover, which determines the length of time that an immigrant to a given habitat will be distinguishable from a longtime resident. A literature survey indicated that few studies have measured turnover rates in fishes and that these have focused on larvae and juveniles. These studies reveal that biomass gain is the primary process driving turnover rates, while metabolic turnover is either minimal or undetectable. Using a simple dilution model and biomass-specific growth rates, I estimated that young fishes with fast growth rates will reflect the isotopic composition of a new diet within days or weeks. Older or slower-growing individuals may take years or never fully equilibrate. Future studies should evaluate the factors that influence turnover rates in fishes during various stages of the life cycle and in different tissues, as well as explore the potential for combining stable isotope and otolith microstructure analyses to examine the relationship between demographic parameters, movement and connectivity.

Development and applications of a safety assessment system for promoting safety culture in nuclear power plants

International Nuclear Information System (INIS)

Takano, Ken-ichi; Hasegawa, Naoko; Hirose, Ayako; Hayase, Ken-ichi

2004-01-01

For past five years, CRIEPI has been continuing efforts to develop and make applications of a 'safety assessment system' which enable to measure the safety level of organization. This report describe about frame of the system, assessment results and its reliability, and relation between labor accident rate in the site and total safety index (TSI), which can be obtained by the principal factors analysis. The safety assessment in this report is based on questionnaire survey of employee. The format and concrete questionnaires were developed using existing literatures including organizational assessment tools. The tailored questionnaire format involved 124 questionnaire items. The assessment results could be considered as a well indicator of the safety level of organization, safety management, and safety awareness of employee. (author)

Safety culture' is integrating 'human' into risk assessment

International Nuclear Information System (INIS)

Sugimoto, Taiji

2014-01-01

Significance of Fukushima nuclear power accident requested reconsideration of safety standards, of which we had usually no doubt. Risk assessment standard (JIS B 9702), Which was used for repetition of database preparation and cumulative assessment, defined allowable risk and residual risk. However, work site and immediate assessment was indispensable beside such assessment so as to ensure safety. Risk of casualties was absolutely not acceptable in principle and judgments to approve allowable risk needed accountability, which was reminded by safety culture proposed by IAEA and also identified by investigation of organizational cause of Columbia accident. Actor of safety culture would be organization and individual, and mainly individual. Realization of safety culture was conducted by personnel having moral consciousness and firm sense of mission in the course of jobs and working daily with sweat pouring. Safety engineering/technology should have framework integrating human as such totality. (T. Tanaka)

Uncertainty analysis in safety assessment

Energy Technology Data Exchange (ETDEWEB)

Lemos, Francisco Luiz de [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN), Belo Horizonte, MG (Brazil); Sullivan, Terry [Brookhaven National Lab., Upton, NY (United States)

1997-12-31

Nuclear waste disposal is a very complex subject which requires the study of many different fields of science, like hydro geology, meteorology, geochemistry, etc. In addition, the waste disposal facilities are designed to last for a very long period of time. Both of these conditions make safety assessment projections filled with uncertainty. This paper addresses approaches for treatment of uncertainties in the safety assessment modeling due to the variability of data and some current approaches used to deal with this problem. (author) 13 refs.; e-mail: lemos at bnl.gov; sulliva1 at bnl.gov

Safety assessment of foods derived from genetically modified crops

NARCIS (Netherlands)

Kleter, G.A.; Kuiper, H.A.

2003-01-01

The pre-market safety assessment of foods derived from genetically modified crops is carried out according to the consensus approach of "substantial equivalence", in other words: the comparative safety assessment. Currently, the safety assessment of genetically modified foods is harmonized at the

National Waste Repository Novi Han operational safety analysis report. Safety assessment methodology

International Nuclear Information System (INIS)

2003-01-01

The scope of the safety assessment (SA), presented includes: waste management functions (acceptance, conditioning, storage, disposal), inventory (current and expected in the future), hazards (radiological and non-radiological) and normal and accidental modes. The stages in the development of the SA are: criteria selection, information collection, safety analysis and safety assessment documentation. After the review the facilities functions and the national and international requirements, the criteria for safety level assessment are set. As a result from the 2nd stage actual parameters of the facility, necessary for safety analysis are obtained.The methodology is selected on the base of the comparability of the results with the results of previous safety assessments and existing standards and requirements. The procedure and requirements for scenarios selection are described. A radiological hazard categorisation of the facilities is presented. Qualitative hazards and operability analysis is applied. The resulting list of events are subjected to procedure for prioritization by method of 'criticality analysis', so the estimation of the risk is given for each event. The events that fall into category of risk on the boundary of acceptability or are unacceptable are subjected to the next steps of the analysis. As a result the lists with scenarios for PSA and possible design scenarios are established. PSA logical modeling and quantitative calculations of accident sequences are presented

Assessment of safety culture: Changing regulatory approach in Hungary

International Nuclear Information System (INIS)

Ronaky, Jozsef; Toth, Andras

2002-01-01

Hungarian Atomic Energy Authority (HAEA) is changing its inspection practice and assessment methods of safety performance and safety culture in operating nuclear facilities. The new approach emphasises integrated team inspection of safety cornerstones and systematic assessment of safety performance of operators. (author)

Tolerability of risk, safety assessment principles and their implications for probabilistic safety analysis

International Nuclear Information System (INIS)

Ewing, D.J.F.; Campbell, J.F.

1994-01-01

This paper gives a regulatory view of probabilistic safety assessment as seen by the Nuclear Installations Inspectorate (NII) and in the light of the general regulatory risk aims set out in the Health and Safety Executive's (HSE) The tolerability of risk from nuclear power stations (TOR) and in Safety assessment principles for nuclear plants (SAPs), prepared by NII on behalf of the HSE. Both of these publications were revised and republished in 1992. This paper describes the SAPs, together with the historical background, the motivation for review, the effects of the Sizewell and Hinkley Point C public inquiries, changes since the original versions, comparison with international standards and use in assessment. For new plant, probabilistic safety analysis (PSA) is seen as an essential tool in balancing the safety of the design and in demonstrating compliance with TOR and the SAPs. (Author)

The radiation safety self-assessment program of Ontario Hydro

International Nuclear Information System (INIS)

Armitage, G.; Chase, W.J.

1987-01-01

Ontario Hydro has developed a self-assessment program to ensure that high quality in its radiation safety program is maintained. The self-assessment program has three major components: routine ongoing assessment, accident/incident investigation, and detailed assessments of particular radiation safety subsystems or of the total radiation safety program. The operation of each of these components is described

Probabilistic safety assessment for seismic events

International Nuclear Information System (INIS)

1993-10-01

This Technical Document on Probabilistic Safety Assessment for Seismic Events is mainly associated with the Safety Practice on Treatment of External Hazards in PSA and discusses in detail one specific external hazard, i.e. earthquakes

Safety analysis and risk assessment handbook

International Nuclear Information System (INIS)

Peterson, V.L.; Colwell, R.G.; Dickey, R.L.

1997-01-01

This Safety Analysis and Risk Assessment Handbook (SARAH) provides guidance to the safety analyst at the Rocky Flats Environmental Technology Site (RFETS) in the preparation of safety analyses and risk assessments. Although the older guidance (the Rocky Flats Risk Assessment Guide) continues to be used for updating the Final Safety Analysis Reports developed in the mid-1980s, this new guidance is used with all new authorization basis documents. With the mission change at RFETS came the need to establish new authorization basis documents for its facilities, whose functions had changed. The methodology and databases for performing the evaluations that support the new authorization basis documents had to be standardized, to avoid the use of different approaches and/or databases for similar accidents in different facilities. This handbook presents this new standardized approach. The handbook begins with a discussion of the requirements of the different types of authorization basis documents and how to choose the one appropriate for the facility to be evaluated. It then walks the analyst through the process of identifying all the potential hazards in the facility, classifying them, and choosing the ones that need to be analyzed further. It then discusses the methods for evaluating accident initiation and progression and covers the basic steps in a safety analysis, including consequence and frequency binning and risk ranking. The handbook lays out standardized approaches for determining the source terms of the various accidents (including airborne release fractions, leakpath factors, etc.), the atmospheric dispersion factors appropriate for Rocky Flats, and the methods for radiological and chemical consequence assessments. The radiological assessments use a radiological open-quotes templateclose quotes, a spreadsheet that incorporates the standard values of parameters, whereas the chemical assessments use the standard codes ARCHIE and ALOHA

Living probabilistic safety assessment (LPSA)

International Nuclear Information System (INIS)

1999-08-01

Over the past few years many nuclear power plant organizations have performed probabilistic safety assessments (PSAs) to identify and understand key plant vulnerabilities. As a result of the availability of these PSA studies, there is a desire to use them to enhance plant safety and to operate the nuclear stations in the most efficient manner. PSA is an effective tool for this purpose as it assists plant management to target resources where the largest benefit to plant safety can be obtained. However, any PSA which is to be used in this way must have a credible and defensible basis. Thus, it is very important to have a high quality 'living PSA' accepted by the plant and the regulator. With this background in mind, the IAEA has prepared this report on Living Probabilistic Safety Assessment (LPSA) which addresses the updating, documentation, quality assurance, and management and organizational requirements for LPSA. Deficiencies in the areas addressed in this report would seriously reduce the adequacy of the LPSA as a tool to support decision making at NPPs. This report was reviewed by a working group during a Technical Committee Meeting on PSA Applications to Improve NPP Safety held in Madrid, Spain, from 23 to 27 February 1998

Waste isolation safety assessment program. Task 4. Third contractor information meeting

International Nuclear Information System (INIS)

1980-06-01

The Contractor Information Meeting (October 14 to 17, 1979) was part of the FY-1979 effort of Task 4 of the Waste Isolation Safety Assessment Program (WISAP): Sorption/Desorption Analysis. The objectives of this task are to: evaluate sorption/desorption measurement methods and develop a standardized measurement procedure; produce a generic data bank of nuclide-geologic interactions using a wide variety of geologic media and groundwaters; perform statistical analysis and synthesis of these data; perform validation studies to compare short-term laboratory studies to long-term in situ behavior; develop a fundamental understanding of sorption/desorption processes; produce x-ray and gamma-emitting isotopes suitable for the study of actinides at tracer concentrations; disseminate resulting information to the international technical community; and provide input data support for repository safety assessment. Conference participants included those subcontracted to WISAP Task 4, representatives and independent subcontractors to the Office of Nuclear Waste Isolation, representatives from other waste disposal programs, and experts in the area of waste/geologic media interaction. Since the meeting, WISAP has been divided into two programs: Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) (modeling efforts) and Waste/Rock Interactions Technology (WRIT) (experimental work). The WRIT program encompasses the work conducted under Task 4. This report contains the information presented at the Task 4, Third Contractor Information Meeting. Technical Reports from the subcontractors, as well as Pacific Northwest Laboratory (PNL), are provided along with transcripts of the question-and-answer sessions. The agenda and abstracts of the presentations are also included. Appendix A is a list of the participants. Appendix B gives an overview of the WRIT program and details the WRIT work breakdown structure for 1980

Waste isolation safety assessment program. Task 4. Third contractor information meeting

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

The Contractor Information Meeting (October 14 to 17, 1979) was part of the FY-1979 effort of Task 4 of the Waste Isolation Safety Assessment Program (WISAP): Sorption/Desorption Analysis. The objectives of this task are to: evaluate sorption/desorption measurement methods and develop a standardized measurement procedure; produce a generic data bank of nuclide-geologic interactions using a wide variety of geologic media and groundwaters; perform statistical analysis and synthesis of these data; perform validation studies to compare short-term laboratory studies to long-term in situ behavior; develop a fundamental understanding of sorption/desorption processes; produce x-ray and gamma-emitting isotopes suitable for the study of actinides at tracer concentrations; disseminate resulting information to the international technical community; and provide input data support for repository safety assessment. Conference participants included those subcontracted to WISAP Task 4, representatives and independent subcontractors to the Office of Nuclear Waste Isolation, representatives from other waste disposal programs, and experts in the area of waste/geologic media interaction. Since the meeting, WISAP has been divided into two programs: Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) (modeling efforts) and Waste/Rock Interactions Technology (WRIT) (experimental work). The WRIT program encompasses the work conducted under Task 4. This report contains the information presented at the Task 4, Third Contractor Information Meeting. Technical Reports from the subcontractors, as well as Pacific Northwest Laboratory (PNL), are provided along with transcripts of the question-and-answer sessions. The agenda and abstracts of the presentations are also included. Appendix A is a list of the participants. Appendix B gives an overview of the WRIT program and details the WRIT work breakdown structure for 1980.

Probabilistic safety assessment in nuclear power plant management

International Nuclear Information System (INIS)

Holloway, N.J.

1989-06-01

Probabilistic Safety Assessment (PSA) techniques have been widely used over the past few years to assist in understanding how engineered systems respond to abnormal conditions, particularly during a severe accident. The use of PSAs in the design and operation of such systems thus contributes to the safety of nuclear power plants. Probabilistic safety assessments can be maintained to provide a continuous up-to-date assessment (Living PSA), supporting the management of plant operations and modifications

High Flux Isotope Reactor technical specifications

International Nuclear Information System (INIS)

1985-11-01

This report gives technical specifications for the High Flux Isotope Reactor (HFIR) on the following: safety limits and limiting safety system settings; limiting conditions for operation; surveillance requirements; design features; and administrative controls

Types of safety assessments of near surface repository for radioactive waste

International Nuclear Information System (INIS)

Mateeva, M.

2004-01-01

The purpose of this article is to presents the classification of different types safety assessments of near surface repository for low and intermediate level radioactive waste substantiated with results of safety assessments generated in Bulgaria. The different approach of safety assessments applied for old existing repository as well as for site selection for construction new repository is outlined. The regulatory requirements in Bulgaria define three main types of assessments: Safety assessment; Technical substation of repository safety; Assessment of repository influence on environment that is in form of report prepared from the Ministry of environment and waters on the base of results obtained in two first types of assessments. Additionally first type is subdivided in three categories - preliminary safety assessment, safety assessment and post closure safety assessment, which are generated using deterministic approach. The technical substation of repository safety is generated using probabilistic approach. Safety assessment results that are presented here are based on evaluation of existing old repository type 'Radon' in Novi Han and real site selection procedure for new near surface repository for low and intermediate level radioactive waste from nuclear power station in Kozloduy. The important role of safety assessment for improvement the repository safety as well as for repository licensing, correct site selection and right choice of engineer barriers and repository design is discussed using generated results. (author)

Data used for safety assessment of reprocessing facilities

International Nuclear Information System (INIS)

Nomura, Yasushi; Suzuki, Atsuyuki; Kanagawa, Akira

1990-08-01

For safety assessment of a reprocessing facility, it is important to know performance of radioactive materials in their accidental release and transfer. Accordingly, it is necessary to collect and prepare data for use in analyses for their performance. In JAERI, experiments such as for data acquisition, for source-term evaluation and for radioactive material transfer, are now planned to be performed. Prior to these experiments, it is decided to investigate data in use for accidental safety assessment of reprocessing plants and their based experimental data, thus to make it possible to recommend reasonable values for safety analysis parameters by evaluating the investigated results, to select the experimental items, to edit a safety assessment handbook and so on. In this line of objectives, JAERI rewarded a two-year contract of investigation to Nuclear Safety Research Association, to make a working group under a special committee on data investigation for reprocessing facility safety assessment. This report is a collection of results reviewed and checked by the working group. The contents consist of two parts, one for investigation and review of data used for safety assessment of domestic or oversea reprocessing facilities, and the other for investigation, review and evaluation of ANSI recommended American standard data reported by E. Walker together with their based experimental data resorting to the original referred reports. (author)

Safety functions and safety function indicators - key elements in SKB'S methodology for assessing long-term safety of a KBS-3 repository

International Nuclear Information System (INIS)

Hedin, A.

2008-01-01

The application of so called safety function indicators in SKB safety assessment of a KBS-3 repository for spent nuclear fuel is presented. Isolation and retardation are the two main safety functions of the KBS-3 concept. In order to quantitatively evaluate safety on a sub-system level, these functions need to be differentiated, associated with quantitative measures and, where possible, with quantitative criteria relating to the fulfillment of the safety functions. A safety function is defined as a role through which a repository component contributes to safety. A safety function indicator is a measurable or calculable property of a repository component that allows quantitative evaluation of a safety function. A safety function indicator criterion is a quantitative limit such that if the criterion is fulfilled, the corresponding safety function is upheld. The safety functions and their associated indicators and criteria developed for the KBS-3 repository are primarily related to the isolating potential and to physical states of the canister and the clay buffer surrounding the canister. They are thus not directly related to release rates of radionuclides. The paper also describes how the concepts introduced i) aid in focussing the assessment on critical, safety related issues, ii) provide a framework for the accounting of safety throughout the different time frames of the assessment and iii) provide key information in the selection of scenarios for the safety assessment. (author)

Safety and reliability assessment

International Nuclear Information System (INIS)

1979-01-01

This report contains the papers delivered at the course on safety and reliability assessment held at the CSIR Conference Centre, Scientia, Pretoria. The following topics were discussed: safety standards; licensing; biological effects of radiation; what is a PWR; safety principles in the design of a nuclear reactor; radio-release analysis; quality assurance; the staffing, organisation and training for a nuclear power plant project; event trees, fault trees and probability; Automatic Protective Systems; sources of failure-rate data; interpretation of failure data; synthesis and reliability; quantification of human error in man-machine systems; dispersion of noxious substances through the atmosphere; criticality aspects of enrichment and recovery plants; and risk and hazard analysis. Extensive examples are given as well as case studies

Lessons Learned in the Update of a Safety Limit for the High Flux Isotope Reactor

International Nuclear Information System (INIS)

Cook, David Howard

2009-01-01

A recent unreviewed safety question (USQ) regarding a portion of the High Flux Isotope Reactor (HFIR) transient decay heat removal analysis focused on applicability of a heat transfer correlation at the low flow end of reactor operations. During resolution of this issue, review of the correlations used to establish the safety limit (SL) on reactor flux-to-flow ratio revealed the need to change the magnitude of the SL at the low flow end of reactor operations and the need to update the hot spot fuel damage criteria to incorporate current knowledge involving parallel channel flow stability. Because of the original safety design strategy for the reactor, resolution of the issues for the flux-to-flow ratio involved reevaluation of all key process variable SLs and limiting control settings (LCSs) using the current version of the heat transfer analysis code for the reactor. Goals of the work involved updating and upgrading the SL analysis where necessary, while preserving the safety design strategy for the reactor. Changes made include revisions to the safety design criteria at low flows to address the USQ, update of the process- and analysis input-variable uncertainty considerations, and upgrade of the safety design criteria at high flow. The challenges faced during update/upgrade of this SL and LCS are typical of the problems found in the integration of safety into the design process for a complex facility. In particular, the problems addressed in the area of instrument uncertainties provide valuable lessons learned for establishment and configuration control of SLs for large facilities

Isotope laboratories

International Nuclear Information System (INIS)

1978-01-01

This report from the Dutch Ministry of Health is an advisory document concerned with isotope laboratories in hospitals, in connection with the Dutch laws for hospitals. It discusses which hospitals should have isotope laboratories and concludes that as many hospitals as possible should have small laboratories so that emergency cases can be dealt with. It divides the Netherlands into regions and suggests which hospitals should have these facilities. The questions of how big each lab. is to be, what equipment each has, how each lab. is organised, what therapeutic and diagnostic work should be carried out by each, etc. are discussed. The answers are provided by reports from working groups for in vivo diagnostics, in vitro diagnostics, therapy, and safety and their results form the criteria for the licences of isotope labs. The results of a questionnaire for isotope labs. already in the Netherlands are presented, and their activities outlined. (C.F.)

Safety assessment as basis for the decision making process

International Nuclear Information System (INIS)

Ilie, P.; Didita, L.; Danchiv, A.

2005-01-01

This paper deals with the safety assessment for a new near surface repository, particularly for the early stage of repository development using ISAM (Improvement of Safety Assessment Methodologies for Near Surface Disposal Facilities) safety assessment methodology. In this stage of the repository life cycle the main purpose of the safety assessment is to demonstrate that the plant is capable to be constructed and operated safely. The paper is based on development of the ASAM (Application of the Safety Assessment Methodologies for Near-Surface Disposal Facilities) Decision Support Subgroup of the Common Aspects Working Group. The implications of decision making for the application of the ISAM methodology on post-closure safety assessment are analysed. Some important elements of the decision-making process with impact on key components of the ISAM process are described. Following the development of Decision Support Subgroup of the ASAM Common Aspects Working Group the proposed change of ISAM methodology is analysed. This approach puts all activities in a decision context where the first iteration of the safety assessment is based on the existing state of knowledge and the initial engineering design. Confidence in the process is accomplished through the direct inclusion of all decision makers and stakeholders in the formulation of decisions, the definition of the state of knowledge, and decision making activities. The decision process is developed in context of undertaking assessments with little site-specific information, this situation is specifically for new planned repository. Limited site-specific information can result in a high degree of uncertainty, therefore it is important first of all to identify the sources of uncertainty arising from the limited nature of the site-specific information and then to apply appropriate approaches to manage the uncertainties and to determine whether the uncertainties are important to the overall safety of the disposal facility

Assessment of safety culture at INPP

International Nuclear Information System (INIS)

Lesin, S.

2002-01-01

Safety Culture covers all main directions of plant activities and the plant departments involved through integration into the INPP Quality Assurance System. Safety Culture is represented by three components. The first is the clear INPP Safety and Quality Assurance Policy. Based on the Policy INPP is safely operated and managers' actions firstly aim at safety assurance. The second component is based on personal responsibility for safety and attitude of each employee of the plant. The third component is based on commitment to safety and competence of managers and employees of the plant. This component links the first two to ensure efficient management of safety at the plant. The above mentioned components including the elements which may significantly affect Safety Culture are also presented in the attachment. The concept of such model implies understanding of effect of different factors on the level of Safety Culture in the organization. In order to continuously correct safety problems, self-assessment of the Safety Culture level is performed at regular intervals. (author)

Safety assessment for radioactive waste disposal facility

International Nuclear Information System (INIS)

Thanaletchumy Karuppiah; Mohd Abdul Wahab Yusof; Nik Marzuki Nik Ibrahim; Nurul Wahida Ahmad Khairuddin

2008-08-01

Safety assessments are used to evaluate the performance of a radioactive waste disposal facility and its impact on human health and the environment. This paper presents the overall information and methodology to carry out the safety assessment for a long term performance of a disposal system. A case study was also conducted to gain hands-on experience in the development and justification of scenarios, the formulation and implementation of models and the analysis of results. AMBER code using compartmental modeling approach was used to represent the migration and fate of contaminants in this training. This safety assessment is purely illustrative and it serves as a starting point for each development stage of a disposal facility. This assessment ultimately becomes more detail and specific as the facility evolves. (Author)

Assessment of local and regional isotopic equilibrium in the mantle

Energy Technology Data Exchange (ETDEWEB)

Hofmann, A W; Hart, S R [Carnegie Institution of Washington, D.C. (USA). Dept. of Terrestrial Magnetism

1978-02-01

The assumption of local equilibrium during partial melting is fundamental to the interpretation of isotope and trace element data for mantle-derived rocks. If disequilibrium melting is significant, the scale of the chemical and isotopic heterogeneity in the mantle indicated by the data could be as small as the grain size of the mantle rock, and the isotope data themselves are then of doubtful value to the understanding of mantle processes. To assess the scale of isotopic heterogeneity in a partially molten asthenosphere the authors review the Sr isotopic data of volcanic rocks from oceanic regions and the available experimental data on diffusion kinetics in minerals and melts similar to those existing in the mantle. Although diffusion data are scarce and afflicted with uncertainties, most of the diffusion coefficients for cations in mantle minerals at temperatures of 1000 to 1200/sup 0/C appear to be greater than 10/sup -13/ cm/sup 2/ s/sup -1/. Struntium diffusion in liquid basalt is more rapid, with diffusion coefficients of D = 10/sup -7/ to 10/sup -6/ cm/sup 2/ s/sup -1/ near 1300/sup 0/C. Simple model calculations show that, with these D values, a fluid-free mantle can maintain a state of disequilibrium on a centimeter scale for periods of 10/sup 8/ to 10/sup 9/ years. The state of disequilibrium found in many mantle-derived xenoliths is thus easily explained. A partially molten mantle, on the other hand, will tend to equilibrate locally in less than 10/sup 5/ to 10/sup 6/ years. The analytical data on natural rocks likewise indicate that the inhomogeneities are both old (> 1.5 b.y.) and regional in character and that the consistent isotopic differences between ocean island and ocean floor volcanics cannot be explained by small-scall hetorogeneity of the source rock.

Preliminary safety assessment of the WIPP facility

International Nuclear Information System (INIS)

Balestri, R.J.; Torres, B.W.; Pahwa, S.B.; Brannen, J.P.

1979-01-01

This paper summarizes the efforts to perform a safety assessment of the Waste Isolation Pilot Plant (WIPP) facility being proposed for southeastern New Mexico. This preliminary safety assessment is limited to a consequence assessment in terms of the dose to a maximally exposed individual as a result of introducing the radionuclides into the biosphere. The extremely low doses to the organs as a result of the liquid breach scenarios are contrasted with the background radiation

LNG Safety Assessment Evaluation Methods

Energy Technology Data Exchange (ETDEWEB)

Muna, Alice Baca [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaFleur, Angela Christine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-05-01

Sandia National Laboratories evaluated published safety assessment methods across a variety of industries including Liquefied Natural Gas (LNG), hydrogen, land and marine transportation, as well as the US Department of Defense (DOD). All the methods were evaluated for their potential applicability for use in the LNG railroad application. After reviewing the documents included in this report, as well as others not included because of repetition, the Department of Energy (DOE) Hydrogen Safety Plan Checklist is most suitable to be adapted to the LNG railroad application. This report was developed to survey industries related to rail transportation for methodologies and tools that can be used by the FRA to review and evaluate safety assessments submitted by the railroad industry as a part of their implementation plans for liquefied or compressed natural gas storage ( on-board or tender) and engine fueling delivery systems. The main sections of this report provide an overview of various methods found during this survey. In most cases, the reference document is quoted directly. The final section provides discussion and a recommendation for the most appropriate methodology that will allow efficient and consistent evaluations to be made. The DOE Hydrogen Safety Plan Checklist was then revised to adapt it as a methodology for the Federal Railroad Administration’s use in evaluating safety plans submitted by the railroad industry.

Promoting and assessment of safety culture within regulatory body

International Nuclear Information System (INIS)

Awasthi, Sumit; Bhattacharya, D.; Koley, J.; Krishnamurthy, P.R.

2015-01-01

Regulators have an important role to play in assisting organizations under their jurisdiction to develop positive safety cultures. It is therefore essential for the regulator to have a robust safety culture as an inherent strategy and communication of this strategy to the organizations it supervises. Atomic Energy Regulatory Board (AERB) emphasizes every utility to institute a good safety culture during various stages of a NPP. The regulatory requirement for establishing organisational safety culture within utility at different stages are delineated in the various AERB safety codes which are presented in the paper. Although the review and assessment of the safety culture is a part of AERB’s continual safety supervision through existing review mechanism, AERB do not use any specific indicators for safety culture assessment. However, establishing and nurturing a good safety culture within AERB helps in encouraging the utility to institute the same. At the induction level AERB provides training to its staffs for regulatory orientation which include a specific course on safety culture. Subsequently, the junior staffs are mentored by seniors while involving them in various regulatory processes and putting them as observers during regulatory decision making process. Further, AERB established a formal procedure for assessing and improving safety culture within its staff as a management system process. The paper describes as a case study the above safety culture assessment process established within AERB

Probabilistic safety assessment for research reactors

International Nuclear Information System (INIS)

1986-12-01

Increasing interest in using Probabilistic Safety Assessment (PSA) methods for research reactor safety is being observed in many countries throughout the world. This is mainly because of the great ability of this approach in achieving safe and reliable operation of research reactors. There is also a need to assist developing countries to apply Probabilistic Safety Assessment to existing nuclear facilities which are simpler and therefore less complicated to analyse than a large Nuclear Power Plant. It may be important, therefore, to develop PSA for research reactors. This might also help to better understand the safety characteristics of the reactor and to base any backfitting on a cost-benefit analysis which would ensure that only necessary changes are made. This document touches on all the key aspects of PSA but placed greater emphasis on so-called systems analysis aspects rather than the in-plant or ex-plant consequences

Safety assessment of radioactive wastes storage 'Mironova Gora'

International Nuclear Information System (INIS)

Serbryakov, B.; Karamushka, V.; Ostroborodov, V.

2000-01-01

A project of transforming the radioactive wastes storage 'Mironova Gora' is under development. A safety assessment of this storage facility was performed to gain assurance on the design decision. The assessment, which was based on the safety assessment methods developed for radioactive wastes repositories, is presented in this paper. (author)

Safety studies on Korean fusion DEMO plant using integrated safety assessment methodology

International Nuclear Information System (INIS)

Oh, Kyemin; Kang, Myoung-suk; Heo, Gyunyoung; Kim, Hyoung-chan

2014-01-01

Highlights: •The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant. •The concepts of integrated safety assessment methodology (ISAM) that can be applied in addressing regulatory requirements and recognizing safety issues for K-DEMO were emphasized. •Phenomena identification and ranking table (PIRT) was proposed. It can recognize vulnerabilities of systems and identify the gaps in technical areas requiring additional researches. •This work is expected to contribute on the conceptual design of safety features for K-DEMO to design engineers and the guidance for regulatory requirements to licensers. -- Abstract: The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant (K-DEMO) as a part of R and D program through the National Fusion Research Institute of Korea. Even though nuclear regulation and licensing framework is well setup due to the operating and design experience of Pressurized Water Reactors (PWRs) since 1970s, the regulatory authority of South Korea has concerns on the challenge of facing new nuclear facilities including K-DEMO due to the differences in systems, materials, and inherent safety feature from conventional PWRs. Even though the follow-up of the ITER license process facilitates to deal with significant safety issues of fusion facilities, a licensee as well as a licenser should identify the gaps between ITER and DEMO in terms of safety issues. First we reviewed the methods of conducting safety analysis for unprecedented nuclear facilities such as Generation IV reactors, particularly very high temperature reactor (VHTR), which is called as integrated safety assessment methodology (ISAM). Second, the analysis for the conceptual design of K-DEMO on the basis of ISAM was conducted. The ISAM consists of five analytical tools to develop the safety requirements from licensee

Safety studies on Korean fusion DEMO plant using integrated safety assessment methodology

Energy Technology Data Exchange (ETDEWEB)

Oh, Kyemin; Kang, Myoung-suk [Kyung Hee University, Youngin-si, Gyeonggi-do 446-701 (Korea, Republic of); Heo, Gyunyoung, E-mail: gheo@khu.ac.kr [Kyung Hee University, Youngin-si, Gyeonggi-do 446-701 (Korea, Republic of); Kim, Hyoung-chan [National Fusion Research Institute, Daejeon-si 305-333 (Korea, Republic of)

2014-10-15

Highlights: •The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant. •The concepts of integrated safety assessment methodology (ISAM) that can be applied in addressing regulatory requirements and recognizing safety issues for K-DEMO were emphasized. •Phenomena identification and ranking table (PIRT) was proposed. It can recognize vulnerabilities of systems and identify the gaps in technical areas requiring additional researches. •This work is expected to contribute on the conceptual design of safety features for K-DEMO to design engineers and the guidance for regulatory requirements to licensers. -- Abstract: The purpose of this paper is to suggest methodology that can investigate safety issues and provides a case study for Korean fusion DEMO plant (K-DEMO) as a part of R and D program through the National Fusion Research Institute of Korea. Even though nuclear regulation and licensing framework is well setup due to the operating and design experience of Pressurized Water Reactors (PWRs) since 1970s, the regulatory authority of South Korea has concerns on the challenge of facing new nuclear facilities including K-DEMO due to the differences in systems, materials, and inherent safety feature from conventional PWRs. Even though the follow-up of the ITER license process facilitates to deal with significant safety issues of fusion facilities, a licensee as well as a licenser should identify the gaps between ITER and DEMO in terms of safety issues. First we reviewed the methods of conducting safety analysis for unprecedented nuclear facilities such as Generation IV reactors, particularly very high temperature reactor (VHTR), which is called as integrated safety assessment methodology (ISAM). Second, the analysis for the conceptual design of K-DEMO on the basis of ISAM was conducted. The ISAM consists of five analytical tools to develop the safety requirements from licensee

Self-assessment of operational safety for nuclear power plants

International Nuclear Information System (INIS)

1999-12-01

Self-assessment processes have been continuously developed by nuclear organizations, including nuclear power plants. Currently, the nuclear industry and governmental organizations are showing an increasing interest in the implementation of this process as an effective way for improving safety performance. Self-assessment involves the use of different types of tools and mechanisms to assist the organizations in assessing their own safety performance against given standards. This helps to enhance the understanding of the need for improvements, the feeling of ownership in achieving them and the safety culture as a whole. Although the primary beneficiaries of the self-assessment process are the plant and operating organization, the results of the self-assessments are also used, for example, to increase the confidence of the regulator in the safe operation of an installation, and could be used to assist in meeting obligations under the Convention on Nuclear Safety. Such considerations influence the form of assessment, as well as the type and detail of the results. The concepts developed in this report present the basic approach to self-assessment, taking into consideration experience gained during Operational Safety Review Team (OSART) missions, from organizations and utilities which have successfully implemented parts of a self-assessment programme and from meetings organized to discuss the subject. This report will be used in IAEA sponsored workshops and seminars on operational safety that include the topic of self-assessment

Analysis of truncation limit in probabilistic safety assessment

International Nuclear Information System (INIS)

Cepin, Marko

2005-01-01

A truncation limit defines the boundaries of what is considered in the probabilistic safety assessment and what is neglected. The truncation limit that is the focus here is the truncation limit on the size of the minimal cut set contribution at which to cut off. A new method was developed, which defines truncation limit in probabilistic safety assessment. The method specifies truncation limits with more stringency than presenting existing documents dealing with truncation criteria in probabilistic safety assessment do. The results of this paper indicate that the truncation limits for more complex probabilistic safety assessments, which consist of larger number of basic events, should be more severe than presently recommended in existing documents if more accuracy is desired. The truncation limits defined by the new method reduce the relative errors of importance measures and produce more accurate results for probabilistic safety assessment applications. The reduced relative errors of importance measures can prevent situations, where the acceptability of change of equipment under investigation according to RG 1.174 would be shifted from region, where changes can be accepted, to region, where changes cannot be accepted, if the results would be calculated with smaller truncation limit

An isotope-aided study on the interaction of surface water and groundwater

International Nuclear Information System (INIS)

Ahn, Jong Sung; Kim, Jong Hoon; Yun, Si Tae; Jeong, Chan Ho; Kim, Kae Nam

1987-12-01

The interaction between surface water and groundwater was studied by isotope-aided techniques in the vicinity of the KAERI area. The understanding of surface water and groundwater flow systems and the analysis of geomaterials which provide the pathway of groundwater is important for the hydrogeological safety assessment of the radioactive waste disposal. The results of the analyses of environmental isotopes have shown that the shallow groundwater in this area was originated from the meteoric water which is infiltrated rapidly into the subsurface materials. The higher content of the environmental isotopes in some groundwater samples indicate that this anomalous values is attributed to impermeable, fine-grained materials. Also, the results of hydrochemical analyses of water samples indicate that shallow groundwater and precipitation are well mixed. (Author)

Risk assessment of safety violations for coal mines

Energy Technology Data Exchange (ETDEWEB)

Megan Orsulaka; Vladislav Kecojevicb; Larry Graysona; Antonio Nietoa [Pennsylvania State University, University Park, PA (United States). Dept of Energy and Mineral Engineering

2010-09-15

This article presents an application of a risk assessment approach in characterising the risks associated with safety violations in underground bituminous mines in Pennsylvania using the Mine Safety and Health Administration (MSHA) citation database. The MSHA database on citations provides an opportunity to assess risks in mines through scrutiny of violations of mandatory safety standards. In this study, quantitative risk assessment is performed, which allows determination of the frequency of occurrence of safety violations (through associated citations) as well as the consequences of them in terms of penalty assessments. Focus is on establishing risk matrices on citation experiences of mines, which can give early indication of emerging potentially serious problems. The resulting frequency, consequence and risk rankings present valuable tools for prioritising resource allocations, determining control strategies, and could potentially contribute to more proactive prevention of incidents and injuries.

Healthcare professionals’ views of feedback on patient safety culture assessment.

OpenAIRE

Zwijnenberg, N.C.; Hendriks, M.; Hoogervorst-Schilp, J.; Wagner, C.

2016-01-01

Background: By assessing patient safety culture, healthcare providers can identify areas for improvement in patient safety culture. To achieve this, these assessment outcomes have to be relevant and presented clearly. The aim of our study was to explore healthcare professionals’ views on the feedback of a patient safety culture assessment. Methods: Twenty four hospitals participated in a patient safety culture assessment in 2012. Hospital departments received feedback in a report and on a web...

Safety assessment of research reactors and preparation of the safety analysis report

International Nuclear Information System (INIS)

1994-01-01

This Safety Guide presents guidelines, approved by international consensus, for the preparation, review and assessment of safety documentation for research reactors such as the Safety Analysis Report. While the Guide is most applicable to research reactors in the design and construction stage, it is also recommended for use during relicensing or reassessment of existing reactors

Lifetime Stable isotopes profiles in whale earplug: assessment of foraging and migrations in the Northern Hemisphere

Science.gov (United States)

Mansouri, F.; Crain, D.; Winfield, Z.; Trumble, S.; Usenko, S.

2017-12-01

Whale earplugs, historically used for aging, were used to reconstruct lifetime stable isotope profiles for carbon (δ13C) and nitrogen (δ15N) for individual whales by delaminating lamina within the earplug. These stable isotope profile, which provide Continuous lifetime records of feeding, foraging ecology, and migration, were determined for 20 individuals from 4 baleen species including fin, minke, humpback, and blue whales spanning more than a century (1869 - 2014) using stable isotope analysis. Approximately 1 mg tissue from each lamina (n=1200) was analyzed for carbon and nitrogen stable isotope using continuous flow isotope ratio mass spectrometer (CF-IRMS). This research using whale earplugs have combined age estimates with stable isotope measurements to reconstruct lifetime foraging profiles with a 6-month resolution, providing an unprecedented opportunity to assess periods and trends in dietary fluctuations as well as migration between different foraging area which have distinct isotope values. Trends with these profiles suggest long-term changing in migration, while annual variability highlights seasonal fasting and feeding. Isotopic ratios were also used to identify subpopulations of Atlantic fin whales, which enabled us to assign unidentified humpback and minke whales to the Atlantic or Pacific Oceans. This historical archive of data provides us an unprecedented tool to assess long term marine ecosystem and subsequently marine organism transition to alternate foraging area and shed light on the whale's population status in the Northern hemisphere.

Safety Assessment of Polyether Lanolins as Used in Cosmetics.

Science.gov (United States)

Becker, Lillian C; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan; Heldreth, Bart

The Cosmetic Ingredient Review (CIR) Expert Panel (Panel) assessed the safety of 39 polyether lanolin ingredients as used in cosmetics. These ingredients function mostly as hair conditioning agents, skin conditioning agent-emollients, and surfactant-emulsifying agents. The Panel reviewed available animal and clinical data, from previous CIR safety assessments of related ingredients and components. The similar structure, properties, functions, and uses of these ingredients enabled grouping them and using the available toxicological data to assess the safety of the entire group. The Panel concluded that these polyether lanolin ingredients are safe in the practices of use and concentration as given in this safety assessment.

Probabilistic safety assessment as a standpoint for decision making

International Nuclear Information System (INIS)

Cepin, M.

2001-01-01

This paper focuses on the role of probabilistic safety assessment in decision-making. The prerequisites for use of the results of probabilistic safety assessment and the criteria for the decision-making based on probabilistic safety assessment are discussed. The decision-making process is described. It provides a risk evaluation of impact of the issue under investigation. Selected examples are discussed, which highlight the described process. (authors)

The Safety Assessment Framework Tool (SAFRAN) - Description, Overview and Applicability

International Nuclear Information System (INIS)

Alujevic, Luka

2014-01-01

The SAFRAN tool (Safety Assessment Framework) is a user-friendly software application that incorporates the methodologies developed in the SADRWMS (Safety Assessment Driven Radioactive Waste Management Solutions) project. The International Atomic Energy Agency (IAEA) organized the International Project on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) to examine international approaches to safety assessment for predisposal management of all types of radioactive waste, including disused sources, small volumes, legacy and decommissioning waste, operational waste, and large volume naturally occurring radioactive material residues. SAFRAN provides aid in: Describing the predisposal RW management activities in a systematic way, Conducting the SA (safety assessment) with clear documentation of the methodology, assumptions, input data and models, Establishing a traceable and transparent record of the safety basis for decisions on the proposed RW management solutions, Demonstrating clear consideration of and compliance with national and international safety standards and recommendations. The SAFRAN tool allows the user to visibly, systematically and logically address predisposal radioactive waste management and decommissioning challenges in a structured way. It also records the decisions taken in such a way that it constitutes a justifiable safety assessment of the proposed management solutions. The objective of this paper is to describe the SAFRAN architecture and features, properly define the terms safety case and safety assessment, and to predict the future development of the SAFRAN tool and assess its applicability to the construction of a future LILW (Low and Intermediate Level Waste) storage facility and repository in Croatia, taking into account all the capabilities and modelling features of the SAFRAN tool. (author)

Safety factors for neutron fluences in NPP safety assessment

International Nuclear Information System (INIS)

Demekhin, V.L.; Bukanov, V.N.; Il'kovich, V.V.; Pugach, A.M.

2016-01-01

In accordance with global practice and a number of existing regulations, the use of conservative approach is required for the calculations related to nuclear safety assessment of NPP. It implies the need to consider the determination of neutron fluence errors that is rather complicated. It is proposed to carry out the consideration by the way of multiplying the neutron fluences obtained with transport calculations by safety factors. The safety factor values are calculated by the developed technique based on the theory of errors, features of the neutron transport calculation code and the results obtained with the code. It is shown that the safety factor value is equal 1.18 with the confidence level of not less than 0.95 for the majority of VVER-1000 reactor places where neutron fluences are determined by MCPV code, and its maximum value is 1.25

Need for an "integrated safety assessment" of GMOs, linking food safety and environmental considerations.

Science.gov (United States)

Haslberger, Alexander G

2006-05-03

Evidence for substantial environmental influences on health and food safety comes from work with environmental health indicators which show that agroenvironmental practices have direct and indirect effects on human health, concluding that "the quality of the environment influences the quality and safety of foods" [Fennema, O. Environ. Health Perspect. 1990, 86, 229-232). In the field of genetically modified organisms (GMOs), Codex principles have been established for the assessment of GM food safety and the Cartagena Protocol on Biosafety outlines international principles for an environmental assessment of living modified organisms. Both concepts also contain starting points for an assessment of health/food safety effects of GMOs in cases when the environment is involved in the chain of events that could lead to hazards. The environment can act as a route of unintentional entry of GMOs into the food supply, such as in the case of gene flow via pollen or seeds from GM crops, but the environment can also be involved in changes of GMO-induced agricultural practices with relevance for health/food safety. Examples for this include potential regional changes of pesticide uses and reduction in pesticide poisonings resulting from the use of Bt crops or influences on immune responses via cross-reactivity. Clearly, modern methods of biotechnology in breeding are involved in the reasons behind the rapid reduction of local varieties in agrodiversity, which constitute an identified hazard for food safety and food security. The health/food safety assessment of GM foods in cases when the environment is involved needs to be informed by data from environmental assessment. Such data might be especially important for hazard identification and exposure assessment. International organizations working in these areas will very likely be needed to initiate and enable cooperation between those institutions responsible for the different assessments, as well as for exchange and analysis of

Ensuring the quality of occupational safety risk assessment.

Science.gov (United States)

Pinto, Abel; Ribeiro, Rita A; Nunes, Isabel L

2013-03-01

In work environments, the main aim of occupational safety risk assessment (OSRA) is to improve the safety level of an installation or site by either preventing accidents and injuries or minimizing their consequences. To this end, it is of paramount importance to identify all sources of hazards and assess their potential to cause problems in the respective context. If the OSRA process is inadequate and/or not applied effectively, it results in an ineffective safety prevention program and inefficient use of resources. An appropriate OSRA is an essential component of the occupational safety risk management process in industries. In this article, we performed a survey to elicit the relative importance for identified OSRA tasks to enable an in-depth evaluation of the quality of risk assessments related to occupational safety aspects on industrial sites. The survey involved defining a questionnaire with the most important elements (tasks) for OSRA quality assessment, which was then presented to safety experts in the mining, electrical power production, transportation, and petrochemical industries. With this work, we expect to contribute to the main question of OSRA in industries: "What constitutes a good occupational safety risk assessment?" The results obtained from the questionnaire showed that experts agree with the proposed OSRA process decomposition in steps and tasks (taxonomy) and also with the importance of assigning weights to obtain knowledge about OSRA task relevance. The knowledge gained will enable us, in the near future, to build a framework to evaluate OSRA quality for industrial sites. © 2012 Society for Risk Analysis.

Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

International Nuclear Information System (INIS)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-01-01

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design

Exploiting data from safety investigations and processes to assess performance of safety management aspects

NARCIS (Netherlands)

Karanikas, Nektarios

2016-01-01

This paper presents an alternative way to use records from safety investigations as a means to support the evaluation of safety management (SM) aspects. Datasets from safety investigation reports and progress records of an aviation organization were analyzed with the scope of assessing safety

NPP Krsko periodic safety review. Safety assessment and analyses

International Nuclear Information System (INIS)

Basic, I.; Spiler, J.; Thaulez, F.

2002-01-01

Definition of a PSR (Periodic Safety Review) project is a comprehensive safety review of a plant after ten years of operation. The objective is a verification by means of a comprehensive review using current methods that the plant remains safe when judged against current safety objectives and practices and that adequate arrangements are in place to maintain plant safety. The overall goals of the NEK PSR Program are defined in compliance with the basic role of a PSR and the current practice typical for most of the countries in EU. This practice is described in the related guides and good practice documents issued by international organizations. The overall goals of the NEK PSR are formulated as follows: to demonstrate that the plant is as safe as originally intended; to evaluate the actual plant status with respect to aging and wear-out identifying any structures, systems or components that could limit the life of the plant in the foreseeable future, and to identify appropriate corrective actions, where needed; to compare current level of safety in the light of modern standards and knowledge, and to identify where improvements would be beneficial for minimizing deviations at justifiable costs. The Krsko PSR will address the following safety factors: Operational Experience, Safety Assessment, EQ and Aging Management, Safety Culture, Emergency Planning, Environmental Impact and Radioactive Waste.(author)

Safety assessment of a lithium target

International Nuclear Information System (INIS)

Burgazzi, Luciano; Roberta, Ferri; Barbara, Giannone

2006-01-01

This paper addresses the safety assessment of the lithium target of the International Fusion Materials Irradiation Facility (IFMIF) through evaluating the most important risk factors related to system operation and verifying the fulfillment of the safety criteria. The hazard assessment is based on using a well-structured Failure Mode and Effect Analysis (FMEA) procedure by detailing on a component-by-component basis all the possible failure modes and identifying their effects on the plant. Additionally, a systems analysis, applying the fault tree technique, is performed in order to evaluate, from a probabilistic standpoint, all the relevant and possible failures of each component required for safe system operation and assessing the unavailability of the lithium target system. The last task includes the thermal-hydraulic transient analysis of the target lithium loop, including operational and accident transients. A lithium target loop model is developed, using the RELAP5/Mod3.2 thermal-hydraulic code, which has been modified to include specific features of IFMIF itself. The main conclusions are that target safety is fulfilled, the hazards associated with lithium operation are confined within the IFMIF security boundaries, the environmental impact is negligible, and the plant responds to the simulated transients by being able to reach steady conditions in a safety situation

Environment, safety and health progress assessment manual

International Nuclear Information System (INIS)

1992-12-01

On June 27, 1989, the Secretary of Energy announced a 1O-Point Initiative to strengthen environment,safety, and health (ES ampersand H) programs, and waste management activities at involved conducting DOE production, research, and testing facilities. One of the points independent Tiger Team Assessments of DOE operating facilities. The Office of Special Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This volume contains appendices to the Environment, Safety and Health Progress Assessment Manual

The role of natural analogues in safety assessment and acceptability

International Nuclear Information System (INIS)

Papp, Toenis

1987-01-01

The safety assessment must evaluate the level of safety for a repository, the confidence that can be placed on the assessment and how well the repository can meet the acceptance criteria of the society. Many of the processes and phenomena that govern the long term performance of a deep geologic repository for radioactive waste also take place in nature. To investigate these natural analogues and try to validate the models on which the safety assessment are based is a main task in the effort to build of confidence in the safety assessments. The assessment of the safety of a repository can, however, not only be based on good models. The possible role of natural analogues or natural evidence in other parts of the safety assessment is discussed. Specially with regard to - the need to demonstrate that all relevant processes have been taken into account, and that the important ones have been validated to an acceptable level for relevant parameters spans, -the definition and analysis of external scenarios for the safety assessment and for the claim that all reasonable scenarios have been addressed, - the public confidence in the long-term relevance of the acceptance criteria. (author)

Safety assessment of HLW geological disposal system

International Nuclear Information System (INIS)

Naito, Morimasa

2006-01-01

In accordance with the Japanese nuclear program, the liquid waste with a high level of radioactivity arising from reprocessing is solidified in a stable glass matrix (vitrification) in stainless steel fabrication containers. The vitrified waste is referred to as high-level radioactive waste (HLW), and is characterized by very high initial radioactivity which, even though it decreases with time, presents a potential long-term risk. It is therefore necessary to thoroughly manage HLW from human and his environment. After vitrification, HLW is stored for a period of 30 to 50 years to allow cooling, and finally disposed of in a stable geological environment at depths greater than 300 m below surface. The deep underground environment, in general, is considered to be stable over geological timescales compared with surface environment. By selecting an appropriate disposal site, therefore, it is considered to be feasible to isolate the waste in the repository from man and his environment until such time as radioactivity levels have decayed to insignificance. The concept of geological disposal in Japan is similar to that in other countries, being based on a multibarrier system which combines the natural geological environment with engineered barriers. It should be noted that geological disposal concept is based on a passive safety system that does not require any institutional control for assuring long term environmental safety. To demonstrate feasibility of safe HLW repository concept in Japan, following technical steps are essential. Selection of a geological environment which is sufficiently stable for disposal (site selection). Design and installation of the engineered barrier system in a stable geological environment (engineering measures). Confirmation of the safety of the constructed geological disposal system (safety assessment). For site selection, particular consideration is given to the long-term stability of the geological environment taking into account the fact

Environmental Restoration Disposal Facility (Project W-296) Safety Assessment

International Nuclear Information System (INIS)

Armstrong, D.L.

1994-08-01

This Safety Assessment is based on information derived from the Conceptual Design Report for the Environmental Restoration Disposal Facility (DOE/RL 1994) and ancillary documentation developed during the conceptual design phase of Project W-296. The Safety Assessment has been prepared to support the Solid Waste Burial Ground Interim Safety Basis document. The purpose of the Safety Assessment is to provide an evaluation of the design to determine if the process, as proposed, will comply with US Department of Energy (DOE) Limits for radioactive and hazardous material exposures and be acceptable from an overall health and safety standpoint. The evaluation considered affects on the worker, onsite personnel, the public, and the environment

Environmental Restoration Disposal Facility (Project W-296) Safety Assessment

Energy Technology Data Exchange (ETDEWEB)

Armstrong, D.L.

1994-08-01

This Safety Assessment is based on information derived from the Conceptual Design Report for the Environmental Restoration Disposal Facility (DOE/RL 1994) and ancillary documentation developed during the conceptual design phase of Project W-296. The Safety Assessment has been prepared to support the Solid Waste Burial Ground Interim Safety Basis document. The purpose of the Safety Assessment is to provide an evaluation of the design to determine if the process, as proposed, will comply with US Department of Energy (DOE) Limits for radioactive and hazardous material exposures and be acceptable from an overall health and safety standpoint. The evaluation considered affects on the worker, onsite personnel, the public, and the environment.

Stable Isotope Technique to Assess Intake of Human Milk in Breastfed Infants

International Nuclear Information System (INIS)

2014-01-01

This publication was developed by an international group of experts as an integral part of the IAEA’s efforts to contribute to the transfer of technology and knowledge in nutrition. Its aim is to assist Member States in their efforts to combat malnutrition by facilitating the use of relevant nuclear techniques. The stable (non-radioactive) isotope technique has been developed to assess intake of human milk in breastfed infants. The practical application of the stable isotope technique, based on analysis of deuterium by Fourier transform infrared spectrometry (FTIR), is presented in this book

RSAS: a Reactor Safety Assessment System

International Nuclear Information System (INIS)

Sebo, D.E.; Dixon, B.W.; Bray, M.A.

1985-01-01

The Reactor Safety Assessment System (RSAS) is an expert system under development for the United States Nuclear Regulatory Commission (NRC). RSAS is being developed for use at the NRC's Operations Center in the event of a serious incident at a licensed nuclear power plant. The system generates situation assessments for the NRC Reactor Safety Team based on a limited number of plant parameters, known operator actions, and plant status data. The RSAS rule base currently covers one reactor type. The extension of the rule base to other reactor types is also discussed

Safety assessment and detection methods of genetically modified organisms.

Science.gov (United States)

Xu, Rong; Zheng, Zhe; Jiao, Guanglian

2014-01-01

Genetically modified organisms (GMOs), are gaining importance in agriculture as well as the production of food and feed. Along with the development of GMOs, health and food safety concerns have been raised. These concerns for these new GMOs make it necessary to set up strict system on food safety assessment of GMOs. The food safety assessment of GMOs, current development status of safety and precise transgenic technologies and GMOs detection have been discussed in this review. The recent patents about GMOs and their detection methods are also reviewed. This review can provide elementary introduction on how to assess and detect GMOs.

Guidelines for Self-assessment of Research Reactor Safety

International Nuclear Information System (INIS)

2018-01-01

Self-assessment is an organization’s internal process to review its current status, processes and performance against predefined criteria and thereby to provide key elements for the organization’s continual development and improvement. Self-assessment helps the organization to think through what it is expected to do, how it is performing in relation to these expectations, and what it needs to do to improve performance, fulfil the expectations and achieve better compliance with the predefined criteria. This publication provides guidelines for a research reactor operating organization to perform a self-assessment of the safety management and the safety of the facility and to identify gaps between the current situation and the IAEA safety requirements for research reactors. These guidelines also provide a methodology for Member States, regulatory bodies and operating organizations to perform a self-assessment of their application of the provisions of the Code of Conduct on the Safety of Research Reactors. This publication also addresses planning, implementation and follow-up of actions to enhance safety and strengthen application of the Code. The guidelines are applicable to all types of research reactor and critical and subcritical assemblies, at all stages in their lifetimes, and to States, regulatory bodies and operating organizations throughout all phases of research reactor programmes. Research reactor operating organizations can use these guidelines at any time to support self-assessments conducted in accordance with the organization’s integrated management system. These guidelines also serve as a tool for an organization to prepare to receive an IAEA Integrated Safety Assessment of Research Reactors (INSARR) mission. An important result of this is the opportunity for an operating organization to identify focus areas and make safety improvements in advance of an INSARR mission, thereby increasing the effectiveness of the mission and efficiency of the

Safety Culture Assessment at Regulatory Body - PNRA Experience of Implementing IAEA Methodology for Safety Culture Self Assessment

International Nuclear Information System (INIS)

Bhatti, S.A.N.; Arshad, N.

2016-01-01

The prevalence of a good safety culture is equally important for all kind of organizations involved in nuclear business including operating organizations, designers, regulator, etc., and this should be reflected through all the processes and activities of these organizations. The need for inculcating safety culture into regulatory processes and practices is gradually increasing since the major accident at Fukushima. Accordingly, several international fora in last few years repeatedly highlighted the importance of prevalence of safety culture in regulatory bodies as well. The utilisation of concept of safety culture always remained applicable in regulatory activities of PNRA in the form of core values. After the Fukushima accident, PNRA considered it important to check the extent of utilisation of safety culture concept in organizational activities and decided to conduct its “Safety Culture Self-Assessment (SCSA)” for presenting itself as a role model in-order to endorse the fact that safety culture at regulatory authority plays an important role to influence safety culture at licenced facilities.

ASCOT guidelines revised 1996 edition. Guidelines for organizational self-assessment of safety culture and for reviews by the assessment of safety culture in organizations team

International Nuclear Information System (INIS)

1996-01-01

In order to properly assess safety culture, it is necessary to consider the contribution of all organizations which have an impact on it. Therefore, while assessing the safety culture in an operating organization it is necessary to address at least its interfaces with the local regulatory agency, utility corporate headquarters and supporting organizations. These guidelines are primarily intended for use by any organization wishing to conduct a self-assessment of safety culture. They should also serve as a basis for conducting an international peer review of the organization's self-assessment carried out by an ASCOT (Assessment of Safety Culture in Organizations Team) mission

Application of fuzzy set theory for safety culture and safety management assessment of Kartini research reactor

International Nuclear Information System (INIS)

Syarip; Hauptmanns, U.

2000-01-01

The safety culture status of nuclear power plant is usually assessed through interview and/or discussions with personnel and management in plant, and an assessment of the pertinent documentation. The approach for safety culture assessment described in IAEA Safety Series, make uses of a questionnaire composed of questions which require 'Yes' or 'No' as an answer. Hence, it is basically a check-list approach which is quite common for safety assessments in industry. Such a procedure ignores the fact that the expert answering the question usually has knowledge which goes far beyond a mere binary answer. Additionally, many situations cannot readily be described in such restricted terms. Therefore, it was developed a checklist consisting of questions which are formulated such that they require more than a simple 'yes' or 'no' as an answer. This allows one to exploit the expert knowledge of the analyst appropriately by asking him to qualify the degree of compliance of each of the topics examined. The method presented has proved useful in assessing the safety culture and quality of safety management of the research reactor. The safety culture status and the quality of safety management of Kartini research reactor is rated as 'average'. The method is also flexible and allows one to add questions to existing areas or to introduce new areas covering related topics

Criticality safety evaluations - a open-quotes stalking horseclose quotes for integrated safety assessment

International Nuclear Information System (INIS)

Williams, R.A.

1995-01-01

The Columbia Fuel Fabrication Facility of the Westinghouse Commercial Nuclear Fuel Division manufactures low-enriched uranium fuel and associated components for use in commercial pressurized water power reactors. To support development of a comprehensive integrated safety assessment (ISA) for the facility, as well as to address increasing U.S. Nuclear Regulatory Commission (NRC) expectations regarding such a facility's criticality safety assessments, a project is under way to complete criticality safety evaluations (CSEs) of all plant systems used in processing nuclear materials. Each CSE is made up of seven sections, prepared by a multidisciplinary team of process engineers, systems engineers, safety engineers, maintenance representatives, and operators. This paper provides a cursory outline of the type of information presented in a CSE

IRSN-ANCCLI partnership. Work session on Complementary safety assessments - November 2011

International Nuclear Information System (INIS)

Lachaume, Jean-Luc; Lheureux, Yves; Sene, Monique; Sene, Raymond; Jorel, Martial; Lavarenne, Caroline; Rousseau, Jean-Marie; Rebour, Vincent; Baumont, David; Dupuy, Patricia

2011-11-01

After an overview by the ASN of complementary safety assessments and an assessment of 'post-Fukushima' inspections of basic nuclear installations, the contributions (Power Point presentations) of this seminar proposed: the opinion of the Gravelines CLI (local information commission) on the Gravelines complementary safety assessment report, an analysis and discussion by the GSIEN on reports of complementary assessment of safety of nuclear installations with respect to the Fukushima accident, an analysis by the IRSN of complementary safety assessments performed by operators, the IRSN approach to analyze complementary safety assessments, reports on installation conditions, external flooding and seismic hazard, 'meltdown prevention' aspects in the management of accidental situations in EDF reactors

Initial development of a practical safety audit tool to assess fleet safety management practices.

Science.gov (United States)

Mitchell, Rebecca; Friswell, Rena; Mooren, Lori

2012-07-01

Work-related vehicle crashes are a common cause of occupational injury. Yet, there are few studies that investigate management practices used for light vehicle fleets (i.e. vehicles less than 4.5 tonnes). One of the impediments to obtaining and sharing information on effective fleet safety management is the lack of an evidence-based, standardised measurement tool. This article describes the initial development of an audit tool to assess fleet safety management practices in light vehicle fleets. The audit tool was developed by triangulating information from a review of the literature on fleet safety management practices and from semi-structured interviews with 15 fleet managers and 21 fleet drivers. A preliminary useability assessment was conducted with 5 organisations. The audit tool assesses the management of fleet safety against five core categories: (1) management, systems and processes; (2) monitoring and assessment; (3) employee recruitment, training and education; (4) vehicle technology, selection and maintenance; and (5) vehicle journeys. Each of these core categories has between 1 and 3 sub-categories. Organisations are rated at one of 4 levels on each sub-category. The fleet safety management audit tool is designed to identify the extent to which fleet safety is managed in an organisation against best practice. It is intended that the audit tool be used to conduct audits within an organisation to provide an indicator of progress in managing fleet safety and to consistently benchmark performance against other organisations. Application of the tool by fleet safety researchers is now needed to inform its further development and refinement and to permit psychometric evaluation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Animal-Free Chemical Safety Assessment

Directory of Open Access Journals (Sweden)

George D Loizou

2016-07-01

Full Text Available The exponential growth of the Internet of Things and the global popularity and remarkable decline in cost of the mobile phone is driving the digital transformation of medical practice. The rapidly maturing digital, nonmedical world of mobile (wireless devices, cloud computing and social networking is coalescing with the emerging digital medical world of omics data, biosensors and advanced imaging which offers the increasingly realistic prospect of personalized medicine. Described as a potential seismic shift from the current healthcare model to a wellness paradigm that is predictive, preventative, personalized and participatory, this change is based on the development of increasingly sophisticated biosensors which can track and measure key biochemical variables in people. Additional key drivers in this shift are metabolomic and proteomic signatures, which are increasingly being reported as pre-symptomatic, diagnostic and prognostic of toxicity and disease. These advancements also have profound implications for toxicological evaluation and safety assessment of pharmaceuticals and environmental chemicals. An approach based primarily on human in vivo and high-throughput in vitro human cell-line data is a distinct possibility. This would transform current chemical safety assessment practise which operates in a human data poor to a human data rich environment. This could also lead to a seismic shift from the current animal-based to an animal-free chemical safety assessment paradigm.

Exposure calculations for the FRG isotopic heat source project environmental assessment

International Nuclear Information System (INIS)

Metcalf, I.L.

1997-01-01

The report documents the maximum exposure for transfer of the Federal Republic of Germany (FRG) Isotopic Heat Sources from the 324 Building and placed in interim storage at the Central Waste Complex (CWC). These results are to be reported in the Environmental Assessment DOE-EA- 1 21 1

Additional safety assessments. Report by the Nuclear Safety Authority - December 2011

International Nuclear Information System (INIS)

2011-12-01

The first part of this voluminous report proposes an assessment of targeted audits performed in French nuclear installations (water pressurized reactors on the one hand, laboratories, factories and waste and dismantling installations on the other hand) on issues related to the Fukushima accident. The examined issues were the protection against flooding and against earthquake, and the loss of electricity supplies and of cooling sources. The second part addresses the additional safety assessments of the reactors and the European resistance tests: presentation of the French electronuclear stock, earthquake, flooding and natural hazards (installation sizing, safety margin assessment), loss of electricity supplies and cooling systems, management of severe accidents, subcontracting conditions. The third part addresses the same issues for nuclear installations other than nuclear power reactors

Preliminary investigation on reliability assessment of passive safety system

International Nuclear Information System (INIS)

Huang Changfan; Kuang Bo

2012-01-01

The reliability evaluation of passive safety system plays an important part in probabilistic safety assessment (PSA) of nuclear power plant applying passive safety design, which depends quantitatively on reliabilities of passive safety system. According to the object of reliability assessment of passive safety system, relevant parameters are identified. Then passive system behavior during accident scenarios are studied. A practical example of this method is given for the case of reliability assessment of AP1000 passive heat removal system in loss of normal feedwater accident. Key and design parameters of PRHRS are identified and functional failure criteria are established. Parameter combinations acquired by Latin hyper~ cube sampling (LHS) in possible parametric ranges are input and calculations of uncertainty propagation through RELAP5/MOD3 code are carried out. Based on the calculations, sensitivity assessment on PRHRS functional criteria and reliability evaluation of the system are presented, which might provide further PSA with PRHR system reliability. (authors)

Probabilistic safety assessment of the Fugen NPS

International Nuclear Information System (INIS)

Sotsu, Masutake; Iguchi, Yukihiro; Mizuno, Kouichi; Sato, Shinichirou; Shimizu, Miwako

1999-01-01

We performed a probabilistic safety assessment (PSA) on the Fugen NPS. The main topic of assessment was internal factors. We assessment core damage frequency (level 1 PSA) and containment damage frequency (level 2 PSA) during rated operation, and core damage frequency during shutdown (PSA during shutdowns). Our assessment showed that the core damage frequency of Fugen is well below the IAEA criteria for existing plants, that the conditional containment damage during shutdown is almost the target value of 0.1, and that the core damage frequency during shutdown is almost the same as that assessed during operation. These results confirm that the Fugen plant maintains a sufficient safety margin during shutdowns for regular inspections and for refueling. We developed and verified the effectiveness of an accident management plan incorporating the results of the assessment. (author)

Safety standards for near surface disposal and the safety case and supporting safety assessment for demonstrating compliance with the standards

International Nuclear Information System (INIS)

Metcalf, P.

2003-01-01

The report presents the safety standards for near surface disposal (ICRP guidance and IAEA standards) and the safety case and supporting safety assessment for demonstrating compliance with the standards. Special attention is paid to the recommendations for disposal of long-lived solid radioactive waste. The requirements are based on the principle for the same level of protection of future individuals as for the current generation. Two types of exposure are considered: human intrusion and natural processes and protection measures are discussed. Safety requirements for near surface disposal are discussed including requirements for protection of human health and environment, requirements or safety assessments, waste acceptance and requirements etc

Failure rate data for fusion safety and risk assessment

International Nuclear Information System (INIS)

Cadwallader, L.C.

1993-01-01

The Fusion Safety Program (FSP) at the Idaho National Engineering Laboratory (INEL) conducts safety research in materials, chemical reactions, safety analysis, risk assessment, and in component research and development to support existing magnetic fusion experiments and also to promote safety in the design of future experiments. One of the areas of safety research is applying probabilistic risk assessment (PRA) methods to fusion experiments. To apply PRA, we need a fusion-relevant radiological dose code and a component failure rate data base. This paper describes the FSP effort to develop a failure rate data base for fusion-specific components

Fusion blanket inherent safety assessment

International Nuclear Information System (INIS)

Sze, D.K.; Jung, J.; Cheng, E.T.

1986-01-01

Fusion has significant potential safety advantages. There is a strong incentive for designing fusion plants to ensure that inherent safety will be achieved. Accordingly, both the Tokamak Power Systems Studies and MINIMARS have identified inherent safety as a design goal. A necessary condition is for the blanket to maintain its configuration and integrity under all credible accident conditions. A main problem is caused by afterheat removal in an accident condition. In this regard, it is highly desirable to achieve the required level of protection of the plant capital investment and limitation of radioactivity release by systems that rely only on inherent properties of matter (e.g., thermal conductivity, specific heat, etc.) and without the use of active safety equipment. This paper assesses the conditions under which inherent safety is feasible. Three types of accident conditions are evaluated for two blankets. The blankets evaluated are a self cooled vanadium/lithium blanket and a self-cooled vanadium/Flibe blanket. The accident conditions evaluated are: (1) loss-of-flow accident; (2) loss-of-coolant accident (LOCA); and (3) partial loss-of-coolant accident

Mathematical Safety Assessment Approaches for Thermal Power Plants

Directory of Open Access Journals (Sweden)

Zong-Xiao Yang

2014-01-01

Full Text Available How to use system analysis methods to identify the hazards in the industrialized process, working environment, and production management for complex industrial processes, such as thermal power plants, is one of the challenges in the systems engineering. A mathematical system safety assessment model is proposed for thermal power plants in this paper by integrating fuzzy analytical hierarchy process, set pair analysis, and system functionality analysis. In the basis of those, the key factors influencing the thermal power plant safety are analyzed. The influence factors are determined based on fuzzy analytical hierarchy process. The connection degree among the factors is obtained by set pair analysis. The system safety preponderant function is constructed through system functionality analysis for inherence properties and nonlinear influence. The decision analysis system is developed by using active server page technology, web resource integration, and cross-platform capabilities for applications to the industrialized process. The availability of proposed safety assessment approach is verified by using an actual thermal power plant, which has improved the enforceability and predictability in enterprise safety assessment.

Buffer and backfill process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Sellin, Patrik (comp.)

2006-09-15

This document compiles information on processes in the buffer and deposition tunnel backfill relevant for long-term safety of a KBS-repository. It supports the safety assessment SR-Can, which is a preparatory step for a safety assessment that will support the licence application for a final repository in Sweden. The purpose of the process reports is to document the scientific knowledge of the processes to a level required for an adequate treatment of the processes in the safety assessment. The documentation is not exhaustive from a scientific point of view, since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. However, it must be sufficiently detailed to motivate, by arguments founded on scientific understanding, the treatment of each process in the safety assessment. The purpose is further to determine how to handle each process in the safety assessment at an appropriate degree of detail, and to demonstrate how uncertainties are taken care of, given the suggested handling.

Buffer and backfill process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Sellin, Patrik

2006-09-01

This document compiles information on processes in the buffer and deposition tunnel backfill relevant for long-term safety of a KBS-repository. It supports the safety assessment SR-Can, which is a preparatory step for a safety assessment that will support the licence application for a final repository in Sweden. The purpose of the process reports is to document the scientific knowledge of the processes to a level required for an adequate treatment of the processes in the safety assessment. The documentation is not exhaustive from a scientific point of view, since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. However, it must be sufficiently detailed to motivate, by arguments founded on scientific understanding, the treatment of each process in the safety assessment. The purpose is further to determine how to handle each process in the safety assessment at an appropriate degree of detail, and to demonstrate how uncertainties are taken care of, given the suggested handling

A Computer Program for Assessing Nuclear Safety Culture Impact

Energy Technology Data Exchange (ETDEWEB)

Han, Kiyoon; Jae, Moosung [Hanyang Univ., Seoul (Korea, Republic of)

2014-10-15

Through several accidents of NPP including the Fukushima Daiichi in 2011 and Chernobyl accidents in 1986, a lack of safety culture was pointed out as one of the root cause of these accidents. Due to its latent influences on safety performance, safety culture has become an important issue in safety researches. Most of the researches describe how to evaluate the state of the safety culture of the organization. However, they did not include a possibility that the accident occurs due to the lack of safety culture. Because of that, a methodology for evaluating the impact of the safety culture on NPP's safety is required. In this study, the methodology for assessing safety culture impact is suggested and a computer program is developed for its application. SCII model which is the new methodology for assessing safety culture impact quantitatively by using PSA model. The computer program is developed for its application. This program visualizes the SCIs and the SCIIs. It might contribute to comparing the level of the safety culture among NPPs as well as improving the management safety of NPP.

Healthcare professionals? views on feedback of a patient safety culture assessment

OpenAIRE

Zwijnenberg, Nicolien C.; Hendriks, Michelle; Hoogervorst-Schilp, Janneke; Wagner, Cordula

2016-01-01

Background By assessing patient safety culture, healthcare providers can identify areas for improvement in patient safety culture. To achieve this, these assessment outcomes have to be relevant and presented clearly. The aim of our study was to explore healthcare professionals? views on the feedback of a patient safety culture assessment. Methods Twenty four hospitals participated in a patient safety culture assessment in 2012. Hospital departments received feedback in a report and on a websi...

Safety assessment of the liquid-fed ceramic melter process

International Nuclear Information System (INIS)

Buelt, J.L.; Partain, W.L.

1980-08-01

As part of its development program for the solidification of high-level nuclear waste, Pacific Northwest Laboratory assessed the safety issues for a complete liquid-fed ceramic melter (LFCM) process. The LFCM process, an adaption of commercial glass-making technology, is being developed to convert high-level liquid waste from the nuclear fuel cycle into glass. This safety assessment uncovered no unresolved or significant safety problems with the LFCM process. Although in this assessment the LFCM process was not directly compared with other solidification processes, the safety hazards of the LFCM process are comparable to those of other processes. The high processing temperatures of the glass in the LFCM pose no additional significant safety concerns, and the dispersible inventory of dried waste (calcine) is small. This safety assessment was based on the nuclear power waste flowsheet, since power waste is more radioactive than defense waste at the time of solidification, and all accident conditions for the power waste would have greater radiological consequences than those for defense waste. An exhaustive list of possible off-standard conditions and equipment failures was compiled. These accidents were then classified according to severity of consequence and type of accident. Radionuclide releases to the stack were calculated for each group of accidents using conservative assumptions regarding the retention and decontamination features of the process and facility. Two recommendations that should be considered by process designers are given in the safety assessment

Safety assessment of novel foods and strategies to determine their safety in use

International Nuclear Information System (INIS)

Edwards, Gareth

2005-01-01

Safety assessment of novel foods requires a different approach to that traditionally used for the assessment of food chemicals. A case-by-case approach is needed which must be adapted to take account of the characteristics of the individual novel food. A thorough appraisal is required of the origin, production, compositional analysis, nutritional characteristics, any previous human exposure and the anticipated use of the food. The information should be compared with a traditional counterpart of the food if this is available. In some cases, a conclusion about the safety of the food may be reached on the basis of this information alone, whereas in other cases, it will help to identify any nutritional or toxicological testing that may be required to further investigate the safety of the food. The importance of nutritional evaluation cannot be over-emphasised. This is essential for the conduct of toxicological studies in order to avoid dietary imbalances, etc., that might lead to interpretation difficulties, but also in the context of its use as food and to assess the potential impact of the novel food on the human diet. The traditional approach used for chemicals, whereby an acceptable daily intake (ADI) is established with a large safety margin relative to the expected exposure, cannot be applied to foods. The assessment of safety in use should be based upon a thorough knowledge of the composition of the food, evidence from nutritional, toxicological and human studies, expected use of the food and its expected consumption. Safety equates to a reasonable certainty that no harm will result from intended uses under the anticipated conditions of consumption

LANL Safety Conscious Work Environment (SCWE) Self-Assessment

Energy Technology Data Exchange (ETDEWEB)

Hargis, Barbara C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-01-29

On December 21, 2012 Secretary of Energy Chu transmitted to the Defense Nuclear Facilities Safety Board (DNFSB) revised commitments on the implementation plan for Safety Culture at the Waste Treatment and Immobilization Plant. Action 2-5 was revised to require contractors and federal organizations to complete Safety Conscious Work Environment (SCWE) selfassessments and provide reports to the appropriate U.S. Department of Energy (DOE) - Headquarters Program Office by September 2013. Los Alamos National Laboratory (LANL) planned and conducted a Safety Conscious Work Environment (SCWE) Self-Assessment over the time period July through August, 2013 in accordance with the SCWE Self-Assessment Guidance provided by DOE. Significant field work was conducted over the 2-week period August 5-16, 2013. The purpose of the self-assessment was to evaluate whether programs and processes associated with a SCWE are in place and whether they are effective in supporting and promoting a SCWE.

Quantitative risk assessment of digitalized safety systems

Energy Technology Data Exchange (ETDEWEB)

Shin, Sung Min; Lee, Sang Hun; Kang, Hym Gook [KAIST, Daejeon (Korea, Republic of); Lee, Seung Jun [UNIST, Ulasn (Korea, Republic of)

2016-05-15

A report published by the U.S. National Research Council indicates that appropriate methods for assessing reliability are key to establishing the acceptability of digital instrumentation and control (I and C) systems in safety-critical plants such as NPPs. Since the release of this issue, the methodology for the probabilistic safety assessment (PSA) of digital I and C systems has been studied. However, there is still no widely accepted method. Kang and Sung found three critical factors for safety assessment of digital systems: detection coverage of fault-tolerant techniques, software reliability quantification, and network communication risk. In reality the various factors composing digitalized I and C systems are not independent of each other but rather closely connected. Thus, from a macro point of view, a method that can integrate risk factors with different characteristics needs to be considered together with the micro approaches to address the challenges facing each factor.

Safety assessment of high consequence robotics system

International Nuclear Information System (INIS)

Robinson, D.G.; Atcitty, C.B.

1996-01-01

This paper outlines the use of a failure modes and effects analysis for the safety assessment of a robotic system being developed at Sandia National Laboratories. The robotic system, the weigh and leak check system, is to replace a manual process for weight and leakage of nuclear materials at the DOE Pantex facility. Failure modes and effects analyses were completed for the robotics process to ensure that safety goals for the systems have been met. Due to the flexible nature of the robot configuration, traditional failure modes and effects analysis (FMEA) were not applicable. In addition, the primary focus of safety assessments of robotics systems has been the protection of personnel in the immediate area. In this application, the safety analysis must account for the sensitivities of the payload as well as traditional issues. A unique variation on the classical FMEA was developed that permits an organized and quite effective tool to be used to assure that safety was adequately considered during the development of the robotic system. The fundamental aspects of the approach are outlined in the paper

Compound-Specific Isotope Analyses to Assess TCE Biodegradation in a Fractured Dolomitic Aquifer.

Science.gov (United States)

Clark, Justin A; Stotler, Randy L; Frape, Shaun K; Illman, Walter A

2017-01-01

The potential for trichloroethene (TCE) biodegradation in a fractured dolomite aquifer at a former chemical disposal site in Smithville, Ontario, Canada, is assessed using chemical analysis and TCE and cis-DCE compound-specific isotope analysis of carbon and chlorine collected over a 16-month period. Groundwater redox conditions change from suboxic to much more reducing environments within and around the plume, indicating that oxidation of organic contaminants and degradation products is occurring at the study site. TCE and cis-DCE were observed in 13 of 14 wells sampled. VC, ethene, and/or ethane were also observed in ten wells, indicating that partial/full dechlorination has occurred. Chlorine isotopic values (δ 37 Cl) range between 1.39 to 4.69‰ SMOC for TCE, and 3.57 to 13.86‰ SMOC for cis-DCE. Carbon isotopic values range between -28.9 and -20.7‰ VPDB for TCE, and -26.5 and -11.8‰ VPDB for cis-DCE. In most wells, isotopic values remained steady over the 15-month study. Isotopic enrichment from TCE to cis-DCE varied between 0 and 13‰ for carbon and 1 and 4‰ for chlorine. Calculated chlorine-carbon isotopic enrichment ratios (ϵ Cl /ϵ C ) were 0.18 for TCE and 0.69 for cis-DCE. Combined, isotopic and chemical data indicate very little dechlorination is occurring near the source zone, but suggest bacterially mediated degradation is occurring closer to the edges of the plume. © 2016, National Ground Water Association.

Research on fuzzy comprehensive assessment method of nuclear power plant safety culture

International Nuclear Information System (INIS)

Xiang Yuanyuan; Chen Xukun; Xu Rongbin

2012-01-01

Considering the traits of safety culture in nuclear plant, 38 safety culture assessment indexes are established from 4 aspects such as safety values, safety institution, safety behavior and safety sub- stances. Based on it, a comprehensive assessment method for nuclear power plant safety culture is constructed by using AHP (Analytic Hierarchy Process) approach and fuzzy mathematics. The comprehensive assessment method has the quality of high precision and high operability, which can support the decision making of safety culture development. (authors)

Safety/security interface assessments at commercial nuclear power plants

International Nuclear Information System (INIS)

Byers, K.R.; Brown, P.J.; Norderhaug, L.R.

1985-01-01

The findings of the Haynes Task Force Committee (NUREG-0992) are used as the basis for defining safety/security assessment team activities at commercial nuclear power plants in NRC Region V. A safety/security interface assessment outline and the approach used for making the assessments are presented along with the composition of team members. As a result of observing simulated plant emergency conditions during scheduled emergency preparedness exercises, examining security and operational response procedures, and interviewing plant personnel, the team has identified instances where safety/security conflicts can occur

Safety/security interface assessments at commercial nuclear power plants

International Nuclear Information System (INIS)

Byers, K.R.; Brown, P.J.; Norderhaug, L.R.

1985-07-01

The findings of the Haynes Task Force Committee (NUREG-0992) are used as the basis for defining safety/security assessment team activities at commercial nuclear power plants in NRC Region V. A safety/security interface assessment outline and the approach used for making the assessments are presented along with the composition of team members. As a result of observing simulated plant emergency conditions during scheduled emergency preparedness exercises, examining security and operational response procedures, and interviewing plant personnel, the team has identified instances where safety/security conflicts can occur. 2 refs

Safety assessment for Generation IV nuclear systems

International Nuclear Information System (INIS)

Leahy, T.J.

2012-01-01

The Generation IV International Forum (GIF) Risk and Safety Working Group (RSWG) was created to develop an effective approach for the safety of Generation IV advanced nuclear energy systems. Recent RSWG work has focused on the definition of an integrated safety assessment methodology (ISAM) for evaluating the safety of Generation IV systems. ISAM is an integrated 'tool-kit' consisting of 5 analytical techniques that are available and matched to appropriate stages of Generation IV system concept development: 1) qualitative safety features review - QSR, 2) phenomena identification and ranking table - PIRT, 3) objective provision tree - OPT, 4) deterministic and phenomenological analyses - DPA, and 5) probabilistic safety analysis - PSA. The integrated methodology is intended to yield safety-related insights that help actively drive the evolving design throughout the technology development cycle, potentially resulting in enhanced safety, reduced costs, and shortened development time

Nirex safety assessment research programme: 1987/88

International Nuclear Information System (INIS)

George, D.; Hodgkinson, D.P.

1987-01-01

The Nirex Safety Assessment Research programme's objective is to provide information for the radiological safety case for disposing low-level and intermediate-level radioactive wastes in underground repositories. The programme covers a wide range of experimental studies and mathematical modelling for the near and far field. It attempts to develop a quantitative understanding of events and processes which have an impact on the safety of radioactive waste disposal. (U.K.)

Safety assessment requirements for onsite transfers of radioactive material

International Nuclear Information System (INIS)

Opperman, E.K.; Jackson, E.J.; Eggers, A.G.

1992-05-01

This document contains the requirements for developing a safety assessment document for an onsite package containing radioactive material. It also provides format and content guidance to establish uniformity in the safety assessment documentation and to ensure completeness of the information provided

Application of Stable Isotope in Detection of Veterinary Drug Residues

International Nuclear Information System (INIS)

Wang Wei; Liu Zhanfeng; Du Xiaoning

2010-01-01

In recent years, there has happened a series of significant food safety events worldwide, which lower down consumers' confidence in food safety, and they are taking increasing care about the sources of their foods. The safety problem of animal-origin foods has become a global topic for discussion. Therefore, it is a pressing task to establish a precise, sensitive and reliable method for analyzing veterinary drug residue. An introduction of the present status regarding veterinary drug residue analysis was made in the paper, and it briefly summarized the limit of detection (LOD) and quantification (LOQ) which could be reached in veterinary drug residue analysis by isotopic internal standard method domestically and abroad. The paper also made a review of the progress in applied research of stable isotope labeled compound in veterinary drug residue analysis of, such as, antibiotic medicines, furans and sulfonamides. The paper elucidated the great importance of the application of stable isotopes in the sane development of China's food safety system. (authors)

Geosphere process report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Skagius, Kristina

2010-11-01

This report documents geosphere processes identified as relevant to the long-term safety of a KBS-3 repository, and forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Geosphere process report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina (ed.) (Kemakta Konsult AB, Stockholm (Sweden))

2010-11-15

This report documents geosphere processes identified as relevant to the long-term safety of a KBS-3 repository, and forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Research on advanced system safety assessment procedures (4)

International Nuclear Information System (INIS)

Suzuki, Kazuhiko; Shimada, Yukiyasu

2001-03-01

The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. This report surveys the literature on risk assessment and safety design based on the concept of independent protection layers (IPLs). Furthermore, to improve HAZOP System, tool is proposed to construct the basic model and the internal state model. Such HAZOP system is applied to analyze two kinds of processes, where the ability of the proposed system is verified. In addition, risk assessment support system is proposed to integrate safety design environment and assessment result to be used by other plants as well as to enable the underline plant to use other plants' information. This technique can be implemented using web-based safety information systems. (author)

Audit of data and code use in the SR-Can safety assessment

Energy Technology Data Exchange (ETDEWEB)

Hicks, T.W.; Baldwin, T.D. [Galson Sciences Ltd, 5 Grosvenor House, Melton R oad, Oakham, Rutland LE15 6AX (United Kingdom)

2008-03-15

Building on the findings of previous studies on data and code quality assurance (QA) in safety assessments, this report provides a review of data and code QA in the SR-Can safety assessment. The data quality audit aimed to check that the selection and use of data in the SR-Can safety assessment was appropriate, focusing on the data that underpin representations of and assumptions about canister, insert, buffer, and backfill behaviour. The SR-Can Data Report provided the initial focus for examining the traceability and reliability of data used in the safety assessment; the Data Report is one of the series of SR-Can safety assessment reports and, in this review, it was anticipated that it would provide the primary source of data on the canister, insert, buffer, and backfill. However, other safety assessment reports (the SR-Can Main Report, the Initial State Report, the Fuel and Canister Process Report, and the Buffer and Backfill Process Report) were found to provide key information on data used in the safety assessment. The quality audit of codes aimed to check that code use in the SR-Can safety assessment has been justified through a transparent and traceable process of code development and selection. The Model Summary Report provided the focus for reviewing the QA status of the codes used in the safety assessment. As well as highlighting a number of concerns regarding QA aspects of specific data sets, parameter values, and codes used in the SR-Can safety assessment (which are presented in the report), the review has led to several general observations on data and code QA that should be considered by SKB in the development and implementation of a QA system for the SR-Site safety assessment: - The SR-Site safety assessment and associated QA records should include information that demonstrates that a full QA system has been implemented in order to build confidence in the validity of the assessment. - The data and parameter values used directly in the safety

Assessing safety culture using RADAR matrix

International Nuclear Information System (INIS)

Mariscal-Saldana, M. a.; Garcia-Herrero, S.; Toca-Otero, A.

2009-01-01

Santa Maria de Garona nuclear power plant, in collaboration with Burgos University, has proceeded to conduct a pilot project aimed at seeing the possibilities for the RADAR (Results, Approach, Development, Assessment and review) logic of EFQM model, as a tool for self evaluation of Safety Culture in a nuclear power plant. In the work it has sought evidences of Safety culture implanted in the plant, and identify strengths and areas for improvement regarding this Culture. the score obtained by analyzing these strengths and areas for improvements has served to prioritize actions implemented. The nuclear power plant has been submitted voluntarily to the mission SCART (Safety Culture Assessment Review Team), an international review being done for the first time in the world at a plant in operation and the team of experts led by International Agency of Atomic Energy (IAEA) has identified this project as a good practice, an innovative process implemented in the plant, that must be transmitted to other plants. (Author) 10 refs

Developing IAM for Life Cycle Safety Assessment

NARCIS (Netherlands)

Toxopeus, Marten E.; Lutters, Diederick; Nee, Andrew Y.C.; Song, Bin; Ong, Soh-Khim

2013-01-01

This publication discusses aspects of the development of an impact assessment method (IAM) for safety. Compared to the many existing IAM’s for environmentally oriented LCA, this method should translate the impact of a product life cycle on the subject of safety. Moreover, the method should be

Safety assessment of smoke flavouring primary products by the European Food Safety Authority

NARCIS (Netherlands)

Theobald, A.; Arcella, D.; Carere, A.; Croera, C.; Engel, K.H.; Gott, D.; Gurtler, R.; Meier, D.; Pratt, I.; Rietjens, I.M.C.M.; Simon, R.; Walker, R.

2012-01-01

This paper summarises the safety assessments of eleven smoke flavouring primary products evaluated by the European Food Safety Authority (EFSA). Data on chemical composition, content of polyaromatic hydrocarbons and results of genotoxicity tests and subchronic toxicity studies are presented and

Fire safety assessment of tunnel structures

DEFF Research Database (Denmark)

Gkoumas, Konstantinos; Giuliani, Luisa; Petrini, Francesco

2011-01-01

.g. structural and non structural, organizational, human behavior). This is even more truth for the fire safety design of such structures. Fire safety in tunnels is challenging because of the particular environment, bearing in mind also that a fire can occur in different phases of the tunnel’s lifecycle. Plans...... for upgrading fire safety provisions and tunnel management are also important for existing tunnels. In this study, following a brief introduction of issues regarding the above mentioned aspects, the structural performance of a steel rib for a tunnel infrastructure subject to fire is assessed by means...

Safety management system needs assessment.

Science.gov (United States)

2016-04-01

The safety of the traveling public is critical as each year there are approximately 200 highway fatalities in Nebraska and numerous crash injuries. The objective of this research was to conduct a needs assessment to identify the requirements of a sta...

Criticality safety evaluations - a {open_quotes}stalking horse{close_quotes} for integrated safety assessment

Energy Technology Data Exchange (ETDEWEB)

Williams, R.A. [Westinghouse Electric Corp., Columbia, SC (United States)

1995-12-31

The Columbia Fuel Fabrication Facility of the Westinghouse Commercial Nuclear Fuel Division manufactures low-enriched uranium fuel and associated components for use in commercial pressurized water power reactors. To support development of a comprehensive integrated safety assessment (ISA) for the facility, as well as to address increasing U.S. Nuclear Regulatory Commission (NRC) expectations regarding such a facility`s criticality safety assessments, a project is under way to complete criticality safety evaluations (CSEs) of all plant systems used in processing nuclear materials. Each CSE is made up of seven sections, prepared by a multidisciplinary team of process engineers, systems engineers, safety engineers, maintenance representatives, and operators. This paper provides a cursory outline of the type of information presented in a CSE.

Safety and security risk assessments--now demystified!

Science.gov (United States)

White, Donald E

2011-01-01

Safety/security risk assessments no longer need to spook nor baffle healthcare safety/security managers. This grid template provides at-at-glance quick lookup of the possible threats, the affected people and things, a priority ranking of these risks, and a workable solution for each risk. Using the standard document, spreadsheet, or graphics software already available on your computer, you can easily use a scientific method to produce professional looking risk assessments that get quickly understood by both senior managers and first responders alike!

Visualization of Safety Assessment Result Using GIS in SITES

International Nuclear Information System (INIS)

Yun, Bong-Yo; Park, Joo Wan; Park, Se-Moon; Kim, Chang-Lak

2006-01-01

Site Information and Total Environmental database management System (SITES) is an integrated program for overall data analysis, environmental monitoring, and safety analysis that are produced from the site investigation and environmental assessment of the relevant nuclear facility. SITES is composed of three main modules such as Site Environment Characterization database for Unified and Reliable Evaluation system (SECURE), Safety Assessment INTegration system (SAINT) and Site Useful Data Analysis and ALarm system (SUDAL). The visualization function of safety assessment and environmental monitoring results is designed. This paper is to introduce the visualization design method using Geographic Information System (GIS) for SITES

Additional safety assessment of ITER - Addition safety investigation of the INB ITER

International Nuclear Information System (INIS)

2012-01-01

This assessment aims at re-assessing safety margins in the light of events which occurred in Fukushima Daiichi, i.e. extreme natural events challenging the safety of installations. After a presentation of some characteristics of the ITER installation (location, activities, buildings, premise detritiation systems, electric supply, handling means, radioactive materials, chemical products, nuclear risks, specific risks), the report addresses the installation robustness by identifying cliff-edge effect risks which can be related to a loss of confinement of radioactive materials, explosions, a significant increase of exposure level, a possible effect on water sheets, and so on. The next part addresses the various aspects related to a seismic risk: installation sizing (assessment methodology, seismic risk characterization in Cadarache), sizing protection measures, installation compliance, and margin assessment. External flooding is the next addressed risk: installation sizing with respect to this specific risk, protection measures, installation compliance, margin assessment, and studied additional measures. Other extreme natural phenomena are considered (meteorological conditions, earthquake and flood) which may have effects on other installations (dam, canal). Then, the report addresses technical risks like the loss of electric supplies and cooling systems, the way a crisis is managed in terms of technical and human means and organization in different typical accidental cases. Subcontracting practices are also discussed. A synthesis proposes an overview of this additional safety assessment and discusses the impact which could have additional measures which could be implemented

Swedish REGULATORY APPROACH TO SAFETY Assessment AND SEVERE ACCIDENT MANAGEMENT

International Nuclear Information System (INIS)

Frid, W.; Sandervaag, O.

1997-01-01

The Swedish regulatory approach to safety assessment and severe accident management is briefly described. The safety assessment program, which focuses on prevention of incidents and accidents, has three main components: periodic safety reviews, probabilistic safety analysis, and analysis of postulated disturbances and accident progression sequences. Management and man-technology-organisation issues, as well as inspections, play a key role in safety assessment. Basis for severe accident management were established by the Government decisions in 1981 and 1986. By the end of 1988, the severe accident mitigation systems and emergency operating procedures were implemented at all Swedish reactors. The severe accident research has continued after 1988 for further verification of the protection provided by the systems and reduction of remaining uncertainties in risk dominant phenomena

Complementary assessment of the safety of French nuclear power plants

International Nuclear Information System (INIS)

Camarcat, N.; Pouget-Abadie, X.

2011-01-01

As an immediate consequence of the Fukushima accident the French nuclear safety Authority (ASN) asked EDF to perform a complementary safety assessment for each nuclear power plant dealing with 3 points: 1) the consequences of exceptional natural disasters, 2) the consequences of total loss of electrical power, and 3) the management of emergency situations. The safety margin has to be assessed considering 3 main points: first a review of the conformity to the initial safety requirements, secondly the resistance to events overdoing what the facility was designed to stand for, and the feasibility of any modification susceptible to improve the safety of the facility. This article details the specifications of such assessment, the methodology followed by EDF, the task organization and the time schedule. (A.C.)

Assessment of enriched uranium storage safety issues at the Oak Ridge Y-12 Plant

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

This document is an assessment of the technical safety issues pertaining to the storage of EU at the Oak Ridge Y-12 Plant. The purpose of the assessment is to serve as the basis for defining the technical standards for storage of EU at Y-12. A formal assessment of the Y-12 materials acceptance criteria for EU is currently being conducted by a task force cochaired by B. G. Eddy of DOE Oak Ridge Operations and S. 0. Cox of Y-12 Defense Programs. The mission of this technical assessment for storage is obviously dependent on results of the acceptance assessment. Clearly, the two efforts require coordination to avoid inconsistencies. In addition, both these Assessments must be consistent with the Environmental Assessment for EU storage at Y-12.1 Both the Storage Assessment and the Criteria for Acceptance must take cognizance of the fact that a portion of the EU to be submitted for storage in the future is expected to be derived from foreign sources and to include previously irradiated uranium containing significant levels of transuranics, radioactive daughter products, and unstable uranium isotopes that do not occur in the EU stream of the DOE weapons complex. National security considerations may dictate that these materials be accepted despite the fact that they fail to conform to the Acceptance Criteria. This document will attempt to address the complexities inherent in this situation.

Assessment of enriched uranium storage safety issues at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1996-08-01

This document is an assessment of the technical safety issues pertaining to the storage of EU at the Oak Ridge Y-12 Plant. The purpose of the assessment is to serve as the basis for defining the technical standards for storage of EU at Y-12. A formal assessment of the Y-12 materials acceptance criteria for EU is currently being conducted by a task force cochaired by B. G. Eddy of DOE Oak Ridge Operations and S. 0. Cox of Y-12 Defense Programs. The mission of this technical assessment for storage is obviously dependent on results of the acceptance assessment. Clearly, the two efforts require coordination to avoid inconsistencies. In addition, both these Assessments must be consistent with the Environmental Assessment for EU storage at Y-12.1 Both the Storage Assessment and the Criteria for Acceptance must take cognizance of the fact that a portion of the EU to be submitted for storage in the future is expected to be derived from foreign sources and to include previously irradiated uranium containing significant levels of transuranics, radioactive daughter products, and unstable uranium isotopes that do not occur in the EU stream of the DOE weapons complex. National security considerations may dictate that these materials be accepted despite the fact that they fail to conform to the Acceptance Criteria. This document will attempt to address the complexities inherent in this situation

Assessment of safety regulation using an artificial society

International Nuclear Information System (INIS)

Furuta, Kazuo; Nagase, Masaya

2005-01-01

This study proposes using an artificial society to assess impacts of safety regulation on the society. The artificial society used in this study is a multi-agent system, which consists of many agents representing companies. The agents cannot survive unless they get profits by producing some products. Safety regulation functions as the business environment, which the agents will evolve to fit to. We modeled this process of survival and adaptation by the genetic algorithm. Using the proposed model, case simulations were performed to compare various regulation styles, and some interesting insights were obtained how regulation style influences behavior of the agents and then productivity and safety level of the industry. In conclusion, an effective method for assessment of safety regulation has been developed, and then several insights were shown in this study

Integrated Deterministic-Probabilistic Safety Assessment Methodologies

Energy Technology Data Exchange (ETDEWEB)

Kudinov, P.; Vorobyev, Y.; Sanchez-Perea, M.; Queral, C.; Jimenez Varas, G.; Rebollo, M. J.; Mena, L.; Gomez-Magin, J.

2014-02-01

IDPSA (Integrated Deterministic-Probabilistic Safety Assessment) is a family of methods which use tightly coupled probabilistic and deterministic approaches to address respective sources of uncertainties, enabling Risk informed decision making in a consistent manner. The starting point of the IDPSA framework is that safety justification must be based on the coupling of deterministic (consequences) and probabilistic (frequency) considerations to address the mutual interactions between stochastic disturbances (e.g. failures of the equipment, human actions, stochastic physical phenomena) and deterministic response of the plant (i.e. transients). This paper gives a general overview of some IDPSA methods as well as some possible applications to PWR safety analyses. (Author)

Human reliability in probabilistic safety assessments

International Nuclear Information System (INIS)

Nunez Mendez, J.

1989-01-01

Nowadays a growing interest in medioambiental aspects is detected in our country. It implies an assessment of the risk involved in the industrial processess and installations in order to determine if those are into the acceptable limits. In these safety assessments, among which PSA (Probabilistic Safety Assessments), can be pointed out the role played by the human being in the system is one of the more relevant subjects. (This relevance has been demostrated in the accidents happenned). However in Spain there aren't manuals specifically dedicated to asses the human contribution to risk in the frame of PSAs. This report aims to improve this situation providing: a) a theoretical background to help the reader in the understanding of the nature of the human error, b) a guide to carry out a Human Reliability Analysis and c) a selected overwiev of the techniques and methodologies currently applied in this area. (Author)

Probabilistic assessment of NPP safety under aircraft impact

International Nuclear Information System (INIS)

Birbraer, A.N.; Roleder, A.J.; Arhipov, S.B.

1999-01-01

Methodology of probabilistic assessment of NPP safety under aircraft impact is described below. The assessment is made taking into account not only the fact of aircraft fall onto the NPP building, but another casual parameters too, namely an aircraft class, velocity and mass, as well as point and angle of its impact with the building structure. This analysis can permit to justify the decrease of the required structure strength and dynamic loads on the NPP equipment. It can also be especially useful when assessing the safety of existing NPP. (author)

Nirex Safety Assessment Research Programme bibliography, 1990

International Nuclear Information System (INIS)

Cooper, M.J.

1990-10-01

This bibliography lists reports and papers written as part of the Nirex Safety Assessment Research Programme, which is concerned with disposal of low-level and intermediate-level waste (LLW and ILW) and associated radiological assessments. (author)

Understanding and assessing safety culture

International Nuclear Information System (INIS)

Dalling, Ian

1997-01-01

The 'Dalling' integrated model of organisational performance is introduced and described. A principal element of this model is culture, which is dynamically contrasted with the five other interacting critical elements, which comprise: the management system, the knowledge base, corporate leadership, stakeholders and consciousness. All six of these principal driving elements significantly influence health, safety, environmental, security, or any other aspect of organisational performance. It is asserted that the elements of organisational performance must be clearly defined and understood if meaningful measurements are to be carried out and sustained progress made in improving the knowledge of organisational performance. AEA Technology's safety culture research programme is then described together with the application of a safety culture assessment tool to organisations in the nuclear, electricity, transport, and oil and gas industries, both within and outside of the United Kingdom. (author)

The use of probabilistic safety assessments for improving nuclear safety in Europe

International Nuclear Information System (INIS)

Birkhofer, A.

1992-01-01

The political changes in Europe broadened the scope of international nuclear safety matters considerably. The Western world started to receive reliable and increasingly detailed information on Eastern European nuclear technology and took note of a broad range of technical and administrative problems relevant for nuclear safety in these countries. Reunification made Germany a focus of information exchange on these matters. Here, cooperation with the former German Democratic Republic and with other Eastern European countries as well as safety analyses of Soviet-built nuclear power plants started rather early. Meanwhile, these activities are progressing toward all-European cooperation in the nuclear safety sector. This cooperation includes the use of probabilistic safety assessments (PSAs) addressing applications in both Western and Eastern Europe as well as the further development of this methodology in a converging Europe

Risk assessment of safety data link and network communication in digital safety feature control system of nuclear power plant

International Nuclear Information System (INIS)

Lee, Sang Hun; Son, Kwang Seop; Jung, Wondea; Kang, Hyun Gook

2017-01-01

Highlights: • Safety data communication risk assessment framework and quantitative scheme were proposed. • Fault-tree model of ESFAS unavailability due to safety data communication failure was developed. • Safety data link and network risk were assessed based on various ESF-CCS design specifications. • The effect of fault-tolerant algorithm reliability of safety data network on ESFAS unavailability was assessed. - Abstract: As one of the safety-critical systems in nuclear power plants (NPPs), the Engineered Safety Feature-Component Control System (ESF-CCS) employs safety data link and network communication for the transmission of safety component actuation signals from the group controllers to loop controllers to effectively accommodate various safety-critical field controllers. Since data communication failure risk in the ESF-CCS has yet to be fully quantified, the ESF-CCS employing data communication systems have not been applied in NPPs. This study therefore developed a fault tree model to assess the data link and data network failure-induced unavailability of a system function used to generate an automated control signal for accident mitigation equipment. The current aim is to provide risk information regarding data communication failure in a digital safety feature control system in consideration of interconnection between controllers and the fault-tolerant algorithm implemented in the target system. Based on the developed fault tree model, case studies were performed to quantitatively assess the unavailability of ESF-CCS signal generation due to data link and network failure and its risk effect on safety signal generation failure. This study is expected to provide insight into the risk assessment of safety-critical data communication in a digitalized NPP instrumentation and control system.

Savannah River Site K-Reactor Probabilistic Safety Assessment

International Nuclear Information System (INIS)

Brandyberry, M.D.; Bailey, R.T.; Baker, W.H.; Kearnaghan, D.P.; O'Kula, K.R.; Wittman, R.S.; Woody, N.D.; Amos, C.N.; Weingardt, J.J.

1992-12-01

This report gives the results of a Savannah River Site (SRS) K-Reactor Probabilistic Safety Assessment (PSA). Measures of adverse consequences to health and safety resulting from representations of severe accidents in SRS reactors are presented. In addition, the report gives a summary of the methods employed to represent these accidents and to assess the resultant consequences. The report is issued to provide useful information to the U. S. Department of Energy (DOE) on the risk of operation of SRS reactors, for insights into severe accident phenomena that contribute to this risk, and in support of improved bases for other DOE programs in Heavy Water Reactor safety

A novel safety assessment strategy applied to non-selective extracts.

Science.gov (United States)

Koster, Sander; Leeman, Winfried; Verheij, Elwin; Dutman, Ellen; van Stee, Leo; Nielsen, Lene Munch; Ronsmans, Stefan; Noteborn, Hub; Krul, Lisette

2015-06-01

A main challenge in food safety research is to demonstrate that processing of foodstuffs does not lead to the formation of substances for which the safety upon consumption might be questioned. This is especially so since food is a complex matrix in which the analytical detection of substances, and consequent risk assessment thereof, is difficult to determine. Here, a pragmatic novel safety assessment strategy is applied to the production of non-selective extracts (NSEs), used for different purposes in food such as for colouring purposes, which are complex food mixtures prepared from reference juices. The Complex Mixture Safety Assessment Strategy (CoMSAS) is an exposure driven approach enabling to efficiently assess the safety of the NSE by focussing on newly formed substances or substances that may increase in exposure during the processing of the NSE. CoMSAS enables to distinguish toxicologically relevant from toxicologically less relevant substances, when related to their respective levels of exposure. This will reduce the amount of work needed for identification, characterisation and safety assessment of unknown substances detected at low concentration, without the need for toxicity testing using animal studies. In this paper, the CoMSAS approach has been applied for elderberry and pumpkin NSEs used for food colouring purposes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assessment of primary production in a eutrophic lake from carbon and nitrogen isotope ratios of a carnivorous fish

International Nuclear Information System (INIS)

Yoshioka, Takahito

1991-01-01

The carbon and nitrogen isotope ratios of Hypomesus transpacificus (a pond smelt) in a eutrophic lake, Lake Suwa, were measured from April to September in 1986 and 1987. The differences in the isotope ratios between these two years were observed. The stable isotopes were transferred from phytoplankton to zooplankton and pond smelt, associated with organic matters. Therefore, the difference in the isotope ratios in two years seemed to reflect the differences of the proceeding of primary production. It was suggested that the carbon and nitrogen isotope ratios of animal, whose trophic level is far from primary producer, can be the qualitative indicators for assessing the primary production in a lake ecosystem. (author)

Suggestions on the Development of Safety Culture Assessment Method

International Nuclear Information System (INIS)

Choi, Young Sung; Choi, Kwang Sik; Kim, Woong Sik

2006-01-01

Several efforts have been made to assess safety culture of organization that operates nuclear power plants in Korea. The MOST and KINS played a major role to develop assessment methods and KHNP applied them to its NPPs. This paper explains the two methods developed by KINS briefly and presents the insights obtained from the two different applications. It concludes with some suggestions for safety culture assessment based on the insights

Safety assessment of primary system components at the USNRC

Energy Technology Data Exchange (ETDEWEB)

Serpan, C Z; Chen, C Y; Taboada, A

1988-12-31

This document deals with the safety assessment in nuclear reactor components at the USNRC. The USNRC regulations and requirements concerning nuclear reactor design and operations are presented, together with guides and standards which describe how the actions should be implemented. The safety assessment relies on fracture analysis and Non Destructive Examination (NDE). (TEC).

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

International Nuclear Information System (INIS)

Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

2008-12-01

The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments that lie outside the

Assessment of Bacterial Degradation of Aromatic Hydrocarbons in the Environment by Analysis of Stable Carbon Isotope Fractionation

International Nuclear Information System (INIS)

Meckenstock, Rainer U.; Morasch, Barbara; Kaestner, Matthias; Vieth, Andrea; Richnow, Hans Hermann

2002-01-01

13 C/ 12 C stable carbon isotope fractionation was used to assess biodegradation in contaminated aquifers with toluene as a model compound. Different strains of anaerobic bacteria (Thauera aromatica, Geobacter metallireducens, and the sulfate-reducing strain TRM1) showed consistent 13 C/ 12 C carbon isotope fractionation with fractionation factors between αC = 1.0017 and 1.0018. In contrast, three cultures of aerobic organisms, using different mono- and dioxygenase enzyme systems to initiate toluene degradation, showed variable isotope fractionation factors of αC = 1.0027 (Pseudomonasputida strain mt-2), αC = 1.0011 (Ralstonia picketii), andαC = 1.0004 (Pseudomonas putida strain F1). The great variability of isotope fractionation between different aerobic bacterial strains suggests that interpretation of isotope data in oxic habitats can only be qualitative. A soil column was run as a model system for contaminated aquifers with toluene as the carbon source and sulfate as the electron acceptor and samples were taken at different ports along the column. Microbial toluene degradation was calculated based on the 13 C/ 12 C isotope fractionation factors of the batch culture experiments together with the observed 13 C/ 12 C isotope shifts of the residual toluene fractions. The calculated percentage of biodegradation, B, correlated well with the decreasing toluene concentrations at the sampling ports and indicated the increasing extent of biodegradation along the column. The theoretical toluene concentrations as calculated based on the isotope values matched the measured concentrations at the different sampling ports indicating that the Rayleigh equation can be used to calculate biodegradation in quasi closed systems based on measured isotope shifts. A similar attempt was performed to assess toluene degradation in a contaminated, anoxic aquifer. A transect of groundwater wells was monitored along the main direction of the groundwater flow and revealed decreasing

Operational safety review programmes for nuclear power plants. Guidelines for assessment

International Nuclear Information System (INIS)

2002-01-01

The IAEA has been offering the Operational Safety Review Team (OSART) programme to provide advice and assistance to Member States in enhancing the operational safety of nuclear power plants (NPPs). Simultaneously, the IAEA has encouraged self-assessment and review by Member States of their own nuclear power plants to continuously improve nuclear safety. Currently, some utilities have been implementing safety review programmes to independently review their own plants. Corporate or national operational safety review programmes may be compliance or performance based. Successful utilities have found that both techniques are necessary to provide assurance that (i) as a minimum the NPP meets specific corporate and legal requirements and (ii) management at the NPP is encouraged to pursue continuous improvement principles. These programmes can bring nuclear safety benefits to the plants and utilities. The IAEA has conducted two pilot missions to assess the effectiveness of the operational review programme. Based on these missions and on the experience gained during OSART missions, this document has been developed to provide guidance on and broaden national/corporate safety review programmes in Member States, and to assist in maximizing their benefits. These guidelines are intended primarily for the IAEA team to conduct assessment of a national/corporate safety review programme. However, this report may also be used by a country or utility to establish its own national/corporate safety review programme. The guidelines may likewise be used for self-assessment or for establishing a baseline when benchmarking other safety review programmes. This report consists of four parts. Section 2 addresses the planning and preparation of an IAEA assessment mission and Sections 3 and 4 deal with specific guidelines for conducting the assessment mission itself

Flamanville 3 EPR, Safety Assessment and On-site Inspections

International Nuclear Information System (INIS)

Piedagnel, Corinne; Tarallo, Francois; Monnot, Bernard

2011-01-01

As a Technical Support Organisation of the French Safety Authority (ASN), the IRSN carries out the safety assessment of EPR project design and participates in the ASN inspections performed at the construction site and in factories. The design assessment consists in defining the safety functions which should be ensured by civil structures, evaluating the EPR Technical Code for Civil works (ETC-C) in which EdF has defined design criteria and construction rules, and carrying out a detailed assessment of a selection of safety-related structures. Those detailed assessments do not consist of a technical control but of an analysis whose objectives are to ensure that design and demonstrations are robust, in accordance with safety and regulatory rules. Most assessments led IRSN to ask EdF to provide additional justification sometimes involving significant modifications. In the light of those complementary justifications and modifications, IRSN concluded that assessments carried out on design studies were globally satisfactory. The participation of IRSN to the on-site inspections led by ASN is a part of the global control of the compliance of the reactor with its safety objectives. For that purpose IRSN has defined a methodology and an inspection program intended to ASN: based on safety functions associated with civil works (confinement and resistance to aggressions), the corresponding behaviour requirements are identified and linked to a list of main civil works elements. During the inspections, deviations to the project's technical specifications or to the rules of the art were pointed out by IRSN. Those deviations cover various items, such as concrete fabrication, concrete pouring methodology, lack of reinforcement in some structures, unadapted welding procedures of the containment leak-tight steel liner and unsatisfactory treatment of concreting joints. The analysis of those problems has revealed flaws in the organisation of the contractors teams together with an

Prospects for probabilistic safety assessment

International Nuclear Information System (INIS)

Hirschberg, S.

1992-01-01

This article provides some reflections on future developments of Probabilistic Safety Assessment (PSA) in view of the present state of the art and evaluates current trends in the use of PSA for safety management. The main emphasis is on Level 1 PSA, although Level 2 aspects are also highlighted to some extent. As a starting point, the role of PSA is outlined from a historical perspective, demonstrating the rapid expansion of the uses of PSA. In this context the wide spectrum of PSA applications and the associated benefits to the users are in focus. It should be kept in mind, however, that PSA, in spite of its merits, is not a self-standing safety tool. It complements deterministic analysis and thus improves understanding and facilitating prioritization of safety issues. Significant progress in handling PSA limitations - such as reliability data, common-cause failures, human interactions, external events, accident progression, containment performance, and source-term issues - is described. This forms a background for expected future developments of PSA. Among the most important issues on the agenda for the future are PSA scope extensions, methodological improvements and computer code advancements, and full exploitation of the potential benefits of applications to operational safety management. Many PSA uses, if properly exercised, lead to safety improvements as well as major burden reductions. The article provides, in addition, International Atomic Energy Agency (IAEA) perspective on the topics covered, as reflected in the current PSA programs of the agency. 74 refs., 6 figs., 1 tab

The practice of pre-marketing safety assessment in drug development.

Science.gov (United States)

Chuang-Stein, Christy; Xia, H Amy

2013-01-01

The last 15 years have seen a substantial increase in efforts devoted to safety assessment by statisticians in the pharmaceutical industry. While some of these efforts were driven by regulations and public demand for safer products, much of the motivation came from the realization that there is a strong need for a systematic approach to safety planning, evaluation, and reporting at the program level throughout the drug development life cycle. An efficient process can help us identify safety signals early and afford us the opportunity to develop effective risk minimization plan early in the development cycle. This awareness has led many pharmaceutical sponsors to set up internal systems and structures to effectively conduct safety assessment at all levels (patient, study, and program). In addition to process, tools have emerged that are designed to enhance data review and pattern recognition. In this paper, we describe advancements in the practice of safety assessment during the premarketing phase of drug development. In particular, we share examples of safety assessment practice at our respective companies, some of which are based on recommendations from industry-initiated working groups on best practice in recent years.

Training courses on integrated safety assessment modelling for waste repositories

International Nuclear Information System (INIS)

Mallants, D.

2007-01-01

Near-surface or deep repositories of radioactive waste are being developed and evaluated all over the world. Also, existing repositories for low- and intermediate-level waste often need to be re-evaluated to extend their license or to obtain permission for final closure. The evaluation encompasses both a technical feasibility as well as a safety analysis. The long term safety is usually demonstrated by means of performance or safety assessment. For this purpose computer models are used that calculate the migration of radionuclides from the conditioned radioactive waste, through engineered barriers to the environment (groundwater, surface water, and biosphere). Integrated safety assessment modelling addresses all relevant radionuclide pathways from source to receptor (man), using in combination various computer codes in which the most relevant physical, chemical, mechanical, or even microbiological processes are mathematically described. SCK-CEN organizes training courses in Integrated safety assessment modelling that are intended for individuals who have either a controlling or supervising role within the national radwaste agencies or regulating authorities, or for technical experts that carry out the actual post-closure safety assessment for an existing or new repository. Courses are organised by the Department of Waste and Disposal

Human Reliability in Probabilistic Safety Assessments

International Nuclear Information System (INIS)

Nunez Mendez, J.

1989-01-01

Nowadays a growing interest in environmental aspects is detected in our country. It implies an assessment of the risk involved in the industrial processes and installations in order to determine if those are into the acceptable limits. In these safety assessments, among which PSA (Probabilistic Safety Assessments), can be pointed out the role played by the human being in the system is one of the more relevant subjects (This relevance has been demonstrated in the accidents happened) . However, in Spain there aren't manuals specifically dedicated to asses the human contribution to risk in the frame of PSAs. This report aims to improve this situation providing: a) a theoretical background to help the reader in the understanding of the nature of the human error, b) a quid to carry out a Human Reliability Analysis and c) a selected overview of the techniques and methodologies currently applied in this area. (Author) 20 refs

Interim process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Sellin, Patrick

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses

Interim process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Sellin, Patrick (ed.)

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses.

Probabilistic safety assessment goals in Canada

International Nuclear Information System (INIS)

Snell, V.G.

1986-01-01

CANDU safety philosphy, both in design and in licensing, has always had a strong bias towards quantitative probabilistically-based goals derived from comparative safety. Formal probabilistic safety assessment began in Canada as a design tool. The influence of this carried over later on into the definition of the deterministic safety guidelines used in CANDU licensing. Design goals were further developed which extended the consequence/frequency spectrum of 'acceptable' events, from the two points defined by the deterministic single/dual failure analysis, to a line passing through lower and higher frequencies. Since these were design tools, a complete risk summation was not necessary, allowing a cutoff at low event frequencies while preserving the identification of the most significant safety-related events. These goals gave a logical framework for making decisions on implementing design changes proposed as a result of the Probabilistic Safety Analysis. Performing this analysis became a regulatory requirement, and the design goals remained the framework under which this was submitted. Recently, there have been initiatives to incorporate more detailed probabilistic safety goals into the regulatory process in Canada. These range from far-reaching safety optimization across society, to initiatives aimed at the nuclear industry only. The effectiveness of the latter is minor at very low and very high event frequencies; at medium frequencies, a justification against expenditures per life saved in other industries should be part of the goal setting

Probabilistic Safety Assessment of Waste from PyroGreen Processes

International Nuclear Information System (INIS)

Ju, Hee Jae; Ham, In hye; Hwang, Il Soon

2016-01-01

The main object of PyroGreen processes is decontaminating SNFs into intermediate level waste meeting U.S. WIPP contact-handled (CH) waste characteristics to achieve long-term radiological safety of waste disposal. In this paper, radiological impact of PyroGreen waste disposal is probabilistically assessed using domestic input parameters for safety assessment of disposal. PyroGreen processes is decontamination technology using pyro-chemical process developed by Seoul National University in collaboration with KAERI, Chungnam University, Korea Hydro-Nuclear Power and Yonsei University. Advanced Korean Reference Disposal System (A-KRS) design for vitrified waste is applied to develop safety assessment model using GoldSim software. The simulation result shows that PyroGreen vitrified waste is expected to satisfy the regulatory dose limit criteria, 0.1 mSv/yr. With small probability, however, radiological impact to public can be higher than the expected value after 2E5-year. Although the result implies 100 times safety margin even in that case, further study will be needed to assess the sensitivity of other input parameters which can affect the radiological impact for long-term.

Probabilistic Safety Assessment of Waste from PyroGreen Processes

Energy Technology Data Exchange (ETDEWEB)

Ju, Hee Jae; Ham, In hye; Hwang, Il Soon [Seoul National University, Seoul (Korea, Republic of)

2016-05-15

The main object of PyroGreen processes is decontaminating SNFs into intermediate level waste meeting U.S. WIPP contact-handled (CH) waste characteristics to achieve long-term radiological safety of waste disposal. In this paper, radiological impact of PyroGreen waste disposal is probabilistically assessed using domestic input parameters for safety assessment of disposal. PyroGreen processes is decontamination technology using pyro-chemical process developed by Seoul National University in collaboration with KAERI, Chungnam University, Korea Hydro-Nuclear Power and Yonsei University. Advanced Korean Reference Disposal System (A-KRS) design for vitrified waste is applied to develop safety assessment model using GoldSim software. The simulation result shows that PyroGreen vitrified waste is expected to satisfy the regulatory dose limit criteria, 0.1 mSv/yr. With small probability, however, radiological impact to public can be higher than the expected value after 2E5-year. Although the result implies 100 times safety margin even in that case, further study will be needed to assess the sensitivity of other input parameters which can affect the radiological impact for long-term.

Electronuclear's safety culture assessment and enhancement program

International Nuclear Information System (INIS)

Selvatici, E.; Diaz-Francisco, J.M.; Diniz de Souza, V.

2002-01-01

The present paper describes the Eletronuclear's safety culture assessment and enhancement program. The program was launched by the company's top management one year after the creation of Eletronuclear in 1997, from the merging of two companies with different organizational cultures, the design and engineering company Nuclen and the nuclear directorate of the Utility Furnas, Operator of the Angra1 NPP. The program consisted of an assessment performed internally in 1999 with the support and advice of the IAEA. This assessment, performed with the help of a survey, pooled about 80% of the company's employees. The overall result of the assessment was that a satisfactory level of safety culture existed; however, a number of points with a considerable margin for improvement were also identified. These points were mostly related with behavioural matters such as motivation, stress in the workplace, view of mistakes, handling of conflicts, and last but not least a view by a considerable number of employees that a conflict between safety and production might exist. An Action Plan was established by the company managers to tackle these weak points. This Plan was issued as company guideline by the company's Directorate. The subsequent step was to detail and implement the different actions of the Plan, which is the phase that we are at present. In the detailing of the Action Plan, special care was taken to sum up efforts, avoiding duplication of work or competition with already existing programs. In this process it was identified that the company had a considerable number of initiatives directly related to organizational and safety culture improvement, already operational. These initiatives have been integrated in the detailed Action Plan. A new assessment, for checking the effectiveness of the undertaken actions, is planned for 2003. (author)

Development of a quality assurance safety assessment database for near surface radioactive waste disposal

International Nuclear Information System (INIS)

Park, J. W.; Kim, C. L.; Park, J. B.; Lee, E. Y.; Lee, Y. M.; Kang, C. H.; Zhou, W.; Kozak, M. W.

2003-01-01

A quality assurance safety assessment database, called QUARK (QUality Assurance program for Radioactive waste management in Korea), has been developed to manage both analysis information and parameter database for safety assessment of Low- and Intermediate-Level radioactive Waste (LILW) disposal facility in Korea. QUARK is such a tool that serves QA purposes for managing safety assessment information properly and securely. In QUARK, the information is organized and linked to maximize the integrity of information and traceability. QUARK provides guidance to conduct safety assessment analysis, from scenario generation to result analysis, and provides a window to inspect and trace previous safety assessment analysis and parameter values. QUARK also provides default database for safety assessment staff who construct input data files using SAGE(Safety Assessment Groundwater Evaluation), a safety assessment computer code

Safety assessments for deep geological disposal of radioactive wastes

International Nuclear Information System (INIS)

Lyon, R.B.

1984-01-01

The objective of safety assessment for deep geological disposal of radioactive wastes is to evaluate how well the engineered barriers and geological setting inhibit radionuclide migration and prevent radiation dose to man. Safety assessment is influenced through interaction with the regulatory agencies, research groups, the public and the various levels of government. Under the auspices of the IAEA, a generic disposal system description has been developed to facilitate international exchange and comparison of data and results, and to enable development and comparison of performance for all components of the disposal system. It is generally accepted that a systems modelling approach is required and that safety assessment can be considered on two levels. At the systems level, all components of the system are taken into account to evaluate the risk to man. At the systems level, critical review and quality assurance on software provide the major validation techniques. Risk is a combination of dose estimate and probability of that dose. For analysis of the total system to be practical, the components are usually represented by simplified models. Recently, assessments have been taking uncertainties in the input data into account. At the detailed level, large-scale, complex computer programs model components of the system in sufficient detail that validation by comparison with field and laboratory measurements is possible. For example, three-dimensional fluid-flow, heat-transport and solute-transport computer programs have been used. Approaches to safety assessment are described, with illustrations from safety assessments performed in a number of countries. (author)

New safety performance indicators for safety assessment of radioactive waste disposal facilities. Cuban experience

International Nuclear Information System (INIS)

Peralta Vital, J.L.; Castillo, R.G.; Olivera, J.

2002-01-01

The paper shows the Cuban experience on implementing geological disposal of radioactive waste and the necessity for identifying new safety performance indicators for the safety assessment (SA) of radioactive waste disposal facilities. The selected indicator was the concentration of natural radioactive elements (U, Ra, Th, K) in the Cuban geologic environment. We have carried out a group of investigations, which have allowed characterising the concentration for the whole Country, creating a wide database where this indicator is associated with the lithology. The main lithologies in Cuba are: the sedimentary rocks (70 percent of national occurrence), which are present in the three regions (limestone and lutite), and finally the igneous and metamorphic rocks. The results show the concentrations ranges of the natural radionuclides associated fundamentally to the variation in the lithology and geographical area of the Country. In Cuba, the higher concentration (ppm) of Uranium and Radium are referenced to the Central region associated to Skarn, while for Thorium (ppm) and Potassium (%), in the East region the concentration peaks in Tuffs have been found. The concentrations ranges obtained are preliminary, they characterise the behaviour of this parameter for the Cuban geology, but they do not represent limits for safety assessment purposes yet. Also other factors should be taken into account as the assessment context, time scales and others assumptions before establishing the final concentration limits for the natural radionuclides as a radiological and nuclear safety performance indicator complementary to dose and risk for safety assessment for radiological and nuclear facilities. (author)

EFFICIENT QUANTITATIVE RISK ASSESSMENT OF JUMP PROCESSES: IMPLICATIONS FOR FOOD SAFETY

OpenAIRE

Nganje, William E.

1999-01-01

This paper develops a dynamic framework for efficient quantitative risk assessment from the simplest general risk, combining three parameters (contamination, exposure, and dose response) in a Kataoka safety-first model and a Poisson probability representing the uncertainty effect or jump processes associated with food safety. Analysis indicates that incorporating jump processes in food safety risk assessment provides more efficient cost/risk tradeoffs. Nevertheless, increased margin of safety...

Assessment of fibrous insulation materials for the selenide isotope generator system

International Nuclear Information System (INIS)

Wei, G.C; Tennery, V.J.

1977-11-01

Fibrous insulations for use in the converter and the heat source of the radioisotope-powered, selenide element, thermoelectric generator (selenide isotope generator) are assessed. The most recent system design and material selection basis is presented. Several fibrous insulation materials which have the potential for use as load-bearing or nonload-bearing thermal insulations are reviewed, and thermophysical properties supplied by manufacturers or published in the literature are presented. Potential problems with the application of fibrous insulations in the selenide isotope generator are as follows: compatibility with graphite, the thermoelectric elements, and the isolation hot frame; devitrification, grain growth, and sintering with an accompanying degradation of insulation quality; impurity diffusion from the insulation to adjoining structures; outgassing and storage of fibrous materials. Areas in which thermophysical data or quantitative information on the insulation and structural stability is lacking are identified

Value-impact assessment of safety-related modifications

International Nuclear Information System (INIS)

Knowles, W.M.C.; Dinnie, K.S.; Gordon, C.W.

1992-01-01

Like other nuclear utilities, Ontario Hydro, as part of its risk management activities, continually assesses the safety of its nuclear operations. In addition, new regulatory requirements are being applied to the older nuclear power plants. Both of these result in proposed plant modifications designed to reduce the risk to the public. However, modifications to an operating plant can have serious economic effects, and the resources, both financial and personnel, required for the implementation of these modifications are limited. Thus, all potential benefits and effects of a proposed modification must be thoroughly investigated to judge whether the modification is beneficial. Ontario Hydro has begun to use comprehensive value-impact assessments, utilizing plant-specific probabilistic risk assessments (PRAs), as tools to provide an informed basis for judgments on the benefit of safety-related modifications. The results from value-impact assessments can also be used to prioritize the implementation of these modifications

Use of the Home Safety Self-Assessment Tool (HSSAT) within Community Health Education to Improve Home Safety.

Science.gov (United States)

Horowitz, Beverly P; Almonte, Tiffany; Vasil, Andrea

2016-10-01

This exploratory research examined the benefits of a health education program utilizing the Home Safety Self-Assessment Tool (HSSAT) to increase perceived knowledge of home safety, recognition of unsafe activities, ability to safely perform activities, and develop home safety plans of 47 older adults. Focus groups in two senior centers explored social workers' perspectives on use of the HSSAT in community practice. Results for the health education program found significant differences between reported knowledge of home safety (p = .02), ability to recognize unsafe activities (p = .01), safely perform activities (p = .04), and develop a safety plan (p = .002). Social workers identified home safety as a major concern and the HSSAT a promising assessment tool. Research has implications for reducing environmental fall risks.

Formal safety assessment based on relative risks model in ship navigation

Energy Technology Data Exchange (ETDEWEB)

Hu Shenping [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: sphu@mmc.shmtu.edu.cn; Fang Quangen [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: qgfang@mmc.shmtu.edu.cn; Xia Haibo [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: hbxia@mmc.shmtu.edu.cn; Xi Yongtao [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: xiyt@mmc.shmtu.edu.cn

2007-03-15

Formal safety assessment (FSA) is a structured and systematic methodology aiming at enhancing maritime safety. It has been gradually and broadly used in the shipping industry nowadays around the world. On the basis of analysis and conclusion of FSA approach, this paper discusses quantitative risk assessment and generic risk model in FSA, especially frequency and severity criteria in ship navigation. Then it puts forward a new model based on relative risk assessment (MRRA). The model presents a risk-assessment approach based on fuzzy functions and takes five factors into account, including detailed information about accident characteristics. It has already been used for the assessment of pilotage safety in Shanghai harbor, China. Consequently, it can be proved that MRRA is a useful method to solve the problems in the risk assessment of ship navigation safety in practice.

Formal safety assessment based on relative risks model in ship navigation

International Nuclear Information System (INIS)

Hu Shenping; Fang Quangen; Xia Haibo; Xi Yongtao

2007-01-01

Formal safety assessment (FSA) is a structured and systematic methodology aiming at enhancing maritime safety. It has been gradually and broadly used in the shipping industry nowadays around the world. On the basis of analysis and conclusion of FSA approach, this paper discusses quantitative risk assessment and generic risk model in FSA, especially frequency and severity criteria in ship navigation. Then it puts forward a new model based on relative risk assessment (MRRA). The model presents a risk-assessment approach based on fuzzy functions and takes five factors into account, including detailed information about accident characteristics. It has already been used for the assessment of pilotage safety in Shanghai harbor, China. Consequently, it can be proved that MRRA is a useful method to solve the problems in the risk assessment of ship navigation safety in practice

Integrated safety assessment report: Integrated Safety Assessment Program: Millstone Nuclear Power Station, Unit 1 (Docket No. 50-245): Draft report

International Nuclear Information System (INIS)

1987-04-01

The Integrated Safety Assessment Program (ISAP) was initiated in November 1984, by the US Nuclear Regulatory Commission to conduct integrated assessments for operating nuclear power reactors. The integrated assessment is conducted in a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. In addition, procedures will be established to allow for a periodic updating of the schedules to account for licensing issues that arise in the future. This report documents the review of Millstone Nuclear Power Station, Unit No. 1, operated by Northeast Nuclear Energy Company (located in Waterford, Connecticut). Millstone Nuclear Power Station, Unit No. 1, is one of two plants being reviewed under the pilot program for ISAP. This report indicates how 85 topics selected for review were addressed. This report presents the staff's recommendations regarding the corrective actions to resolve the 85 topics and other actions to enhance plant safety. The report is being issued in draft form to obtain comments from the licensee, nuclear safety experts, and the Advisory Committee for Reactor Safeguards (ACRS). Once those comments have been resolved, the staff will present its positions, along with a long-term implementation schedule from the licensee, in the final version of this report

Assessing progress in the development of safety culture

International Nuclear Information System (INIS)

Rotaru, Ioan; Ghita, Sorin

1999-01-01

The concept of safety culture was introduced by the International Nuclear Safety Advisory Group (INSAG) in the Summary Report on the Post-Accident Meeting on the Chernobyl Accident in 1986. The concept was further expanded in the 1988 INSAG-3 report, Basic Safety Principles for Nuclear Power Plants, and again in 1991 in the INSAG-4 report. Recognizing the increasing role that safety culture is expected to play in nuclear installations worldwide, the Convention on Nuclear Safety states the Contracting Parties' desire 'to promote an effective nuclear safety culture'. The concept of safety culture is defined in INSAG-4 as follows: Safety culture is that assembly of characteristics and attitudes in organizations and individuals which establishes that, as an overriding priority, nuclear plant safety issues receive the attention warranted by their significance. Safety culture is also an amalgamation of values, standards, morals and norms of acceptable behaviour. These are aimed at maintaining a self disciplined approach to the enhancement of safety beyond legislative and regulatory requirements. Therefore, the safety culture has to be inherent in the thoughts and actions of all the individuals at every level in an organization. The leadership provided by top management is crucial. Safety culture applies to conventional and personal safety as well as nuclear safety. All safety consideration are affected by common points of beliefs, attitudes, behaviour, and cultural differences, closely linked to a shared system of values and standards. The paper poses questions and tries to find answers relative to issues like: - how to assess progress; - specific organizational indicators of a progressive safety culture; - detection of incipient weaknesses in safety culture (organizational issues, employee issues, technology issues); - revitalizing a weakened safety culture; - overall assesment of safety culture; - general evaluation model. In conclusion, there is no consistent and

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

Energy Technology Data Exchange (ETDEWEB)

Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

2008-12-15

The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments

Improvement of Safety Assessment Methodologies for Near Surface Disposal Facilities

International Nuclear Information System (INIS)

Batandjieva, B.; Torres-Vidal, C.

2002-01-01

The International Atomic Energy Agency (IAEA) Coordinated research program ''Improvement of Safety Assessment Methodologies for Near Surface Disposal Facilities'' (ISAM) has developed improved safety assessment methodology for near surface disposal facilities. The program has been underway for three years and has included around 75 active participants from 40 countries. It has also provided examples for application to three safety cases--vault, Radon type and borehole radioactive waste disposal facilities. The program has served as an excellent forum for exchange of information and good practices on safety assessment approaches and methodologies used worldwide. It also provided an opportunity for reaching broad consensus on the safety assessment methodologies to be applied to near surface low and intermediate level waste repositories. The methodology has found widespread acceptance and the need for its application on real waste disposal facilities has been clearly identified. The ISAM was finalized by the end of 2000, working material documents are available and an IAEA report will be published in 2002 summarizing the work performed during the three years of the program. The outcome of the ISAM program provides a sound basis for moving forward to a new IAEA program, which will focus on practical application of the safety assessment methodologies to different purposes, such as licensing radioactive waste repositories, development of design concepts, upgrading existing facilities, reassessment of operating repositories, etc. The new program will also provide an opportunity for development of guidance on application of the methodology that will be of assistance to both safety assessors and regulators

Isotope Exchange: a Potential Mechanism Regulating the Natural and Anthropogenic Pb Isotope Budget in Coastal Waters

Science.gov (United States)

Chen, M.; Boyle, E. A.; Zurbrick, C.; Carrasco, G. G.; Switzer, A.; Zhao, N.

2016-02-01

Two independent studies on anthropogenic Pb and Pb isotopes in coastal corals from the northern Arabian Gulf and the Singapore Straits have shown an isotopic excursion where the main Pb sources discharging to the water move to more crustal-like values, indicating that the Pb in coastal waters might exchange isotopically with crustal particulates without propotional change in concentration. To investigate this issue, Pb isotope exchange is assessed through a closed-system exchange experiment using estuarine waters collected at the Johor River mouth (discharging to the Singapore Straits). During the experiment, a known amount of NBS-981 (206Pb/207Pb=1.093) was spiked into the unfiltered Johor water (dissolved 206Pb/207Pb = 1.199) and the changing isotopic composition of the dissolved Pb was monitored. Shortly after the spike addition, dissolved Pb exhibited 206Pb/207Pb=1.178, reflecting the influence of the spike. Within the following few days, the 206Pb/207Pb in the water increased to >1.190 with limited changes of the dissolved Pb concentration. The observations in closed-system experiment agree with the isotope difference between Singapore aerosol and seawater in our 2-year-long field observations. The kinetics of isotope exchange were assessed using a simple model, which reproduced >70% of the observed Pb isotope variance. Both the close-system experiment and field measurements imply that isotope exchange can be an important mechanism for regulating the Pb and Pb isotopes in coastal waters. Investigations on the distribution of Pb and Pb isotope in estuaries and coastal waters should further assess the role of isotope exchange in ocean Pb chemistry.

[Agricultural biotechnology safety assessment].

Science.gov (United States)

McClain, Scott; Jones, Wendelyn; He, Xiaoyun; Ladics, Gregory; Bartholomaeus, Andrew; Raybould, Alan; Lutter, Petra; Xu, Haibin; Wang, Xue

2015-01-01

Genetically modified (GM) crops were first introduced to farmers in 1995 with the intent to provide better crop yield and meet the increasing demand for food and feed. GM crops have evolved to include a thorough safety evaluation for their use in human food and animal feed. Safety considerations begin at the level of DNA whereby the inserted GM DNA is evaluated for its content, position and stability once placed into the crop genome. The safety of the proteins coded by the inserted DNA and potential effects on the crop are considered, and the purpose is to ensure that the transgenic novel proteins are safe from a toxicity, allergy, and environmental perspective. In addition, the grain that provides the processed food or animal feed is also tested to evaluate its nutritional content and identify unintended effects to the plant composition when warranted. To provide a platform for the safety assessment, the GM crop is compared to non-GM comparators in what is typically referred to as composition equivalence testing. New technologies, such as mass spectrometry and well-designed antibody-based methods, allow better analytical measurements of crop composition, including endogenous allergens. Many of the analytical methods and their intended uses are based on regulatory guidance documents, some of which are outlined in globally recognized documents such as Codex Alimentarius. In certain cases, animal models are recommended by some regulatory agencies in specific countries, but there is typically no hypothesis or justification of their use in testing the safety of GM crops. The quality and standardization of testing methods can be supported, in some cases, by employing good laboratory practices (GLP) and is recognized in China as important to ensure quality data. Although the number of recommended, in some cases, required methods for safety testing are increasing in some regulatory agencies, it should be noted that GM crops registered to date have been shown to be

Assessing propensity to learn from safety-related events

NARCIS (Netherlands)

Drupsteen, L.; Wybo, J.L.

2015-01-01

Most organisations aim to use experience from the past to improve safety, for instance through learning from safety-related incidents and accidents. Whether an organisation is able to learn successfully can however only be determined afterwards. So far, there are no proactive measures to assess

Healthcare professionals’ views of feedback on patient safety culture assessment.

NARCIS (Netherlands)

Zwijnenberg, N.C.; Hendriks, M.; Hoogervorst-Schilp, J.; Wagner, C.

2016-01-01

Background: By assessing patient safety culture, healthcare providers can identify areas for improvement in patient safety culture. To achieve this, these assessment outcomes have to be relevant and presented clearly. The aim of our study was to explore healthcare professionals’ views on the

Variable Isotopic Compositions of Host Plant Populations Preclude Assessment of Aphid Overwintering Sites

Directory of Open Access Journals (Sweden)

Michael S. Crossley

2017-12-01

Full Text Available Soybean aphid (Aphis glycines Matsumura is a pest of soybean in the northern Midwest whose migratory patterns have been difficult to quantify. Improved knowledge of soybean aphid overwintering sites could facilitate the development of control efforts with exponential impacts on aphid densities on a regional scale. In this preliminary study, we explored the utility of variation in stable isotopes of carbon and nitrogen to distinguish soybean aphid overwintering origins. We compared variation in bulk 13C and 15N content in buckthorn (Rhamnus cathartica L. and soybean aphids in Wisconsin, among known overwintering locations in the northern Midwest. Specifically, we looked for associations between buckthorn and environmental variables that could aid in identifying overwintering habitats. We detected significant evidence of correlation between the bulk 13C and 15N signals of soybean aphids and buckthorn, despite high variability in stable isotope composition within and among buckthorn plants. Further, the 15N signal in buckthorn varied predictably with soil composition. However, lack of sufficient differentiation of geographic areas along axes of isotopic and environmental variation appears to preclude the use of carbon and nitrogen isotopic signals as effective predictors of likely aphid overwintering sites. These preliminary data suggest the need for future work that can further account for variability in 13C and 15N within/among buckthorn plants, and that explores the utility of other stable isotopes in assessing likely aphid overwintering sites.

Application of the Integrated Safety Assessment methodology to safety margins. Dynamic Event Trees, Damage Domains and Risk Assessment

International Nuclear Information System (INIS)

Ibánez, L.; Hortal, J.; Queral, C.; Gómez-Magán, J.; Sánchez-Perea, M.; Fernández, I.; Meléndez, E.; Expósito, A.; Izquierdo, J.M.; Gil, J.; Marrao, H.; Villalba-Jabonero, E.

2016-01-01

The Integrated Safety Assessment (ISA) methodology, developed by the Consejo de Seguridad Nuclear, has been applied to an analysis of Zion NPP for sequences with Loss of the Component Cooling Water System (CCWS). The ISA methodology proposal starts from the unfolding of the Dynamic Event Tree (DET). Results from this first step allow assessing the sequence delineation of standard Probabilistic Safety Analysis results. For some sequences of interest of the outlined DET, ISA then identifies the Damage Domain (DD). This is the region of uncertain times and/or parameters where a safety limit is exceeded, which indicates the occurrence of certain damage situation. This paper illustrates application of this concept obtained simulating sequences with MAAP and with TRACE. From information of simulation results of sequence transients belonging to the DD and the time-density probability distributions of the manual actions and of occurrence of stochastic phenomena, ISA integrates the dynamic reliability equations proposed to obtain the sequence contribution to the global Damage Exceedance Frequency (DEF). Reported results show a slight increase in the DEF for sequences investigated following a power uprate from 100% to 110%. This demonstrates the potential use of the method to help in the assessment of design modifications. - Highlights: • This paper illustrates an application of the ISA methodology to safety margins. • Dynamic Event Trees are useful tool for verifying the standard PSA Event Trees. • The ISA methodology takes into account the uncertainties in human action times. • The ISA methodology shows the Damage Exceedance Frequency increase in power uprates.

Guidance on the safety assessment methodology for storage of radioactive waste

International Nuclear Information System (INIS)

Kinyanjui, M.N.

2014-04-01

This project on safety assessment on storage was carried out with the main objective of ensuring safety of human life and our environment. This is the fundamental principle of radiation protection. Safety assessment has been evaluated as a tool in the safety case in the pre-construction, operational and the post closure phase of storage. In particular the iterative process of evaluating and predicting safety scenarios at each stage of the process has proved to be prudent. It is important that this concept be adopted for this type of facility to ensure safety of mankind and the environment now and in the future.

Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 1 - guideword applicability and method description.

Science.gov (United States)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-12-15

Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design.

MAPLE-X10 reactor safety assessment

International Nuclear Information System (INIS)

Cotnam, K.D.; Lounsbury, R.I.; Gillespie, G.E.

1990-01-01

This paper reports on the safety assessment of the 10 MW MAPLE-X10 reactor which has involved a substantial component of PSA analysis to supplement deterministic analysis. Initiating events are identified through the use of a master logic diagram. The events are then examined through event sequence diagrams, at the concept design stage, followed by a set of reliability analyses that are coordinated with the event sequence diagrams. Improvements identified through the reliability analyses are incorporated into the design to ensure that safety objectives are attained

Dual isotope plots reflect transformation pathways of pesticides: Potential to assess pesticide fate and elucidate transformation mechanisms

Science.gov (United States)

Meyer, Armin; Penning, Holger; Sorensen, Sebastian; Aamand, Jens; Elsner, Martin

2010-05-01

The degradation of pesticides in deeper soil layers and groundwater is of growing interest, because they have repeatedly been found in drinking water supply wells and may pose a risk to future water resources. Current assessment schemes face a common problem, however: natural degradation often cannot be reliably assessed by concentration measurements alone, since mass balances are difficult to establish and transformation cannot be distinguished from sorption or dilution. Even detection of metabolites may only give an incomplete picture. When several transformation pathways occur, some metabolites may be degraded or form bound residues so that the associated pathways may be missed. Our research shows that dual isotope plots derived from compound specific isotope analysis offer a novel approach to give additional, complementary insight into the natural degradation of pesticides. Detection of metabolites is not required, since the isotope fractionation can be fully observed in the pesticide itself. Specifically, different initial biotransformation reactions of the phenylurea herbicide isoproturon (3-(4-isopropylphenyl)-1,1-dimethylurea) in pure culture experiments with bacterial and fungal strains showed strongly pathway-dependent isotope fractionation. When analyzing isotopic changes in different parts of the isoproturon molecule, hydroxylation of the isopropyl group by fungi was found to be associated with C and H isotope fractionation. In contrast, hydrolysis by Arthrobacter globiformis D47 caused strong C and N isotope fractionation, albeit in a different manner than abiotic hydrolysis so that isotope measurements can distinguish between both modes of transformation. Likewise, we observed highly pathway-dependent C and N isotope fractionation of atrazine (1-chloro-3-ethylamino-5-isopropylamino-2,4,6-triazine). Desalkylation of atrazine by Rhodococcus sp. strain NI86/21 resulted in enrichment of both 13-C and 15-N in atrazine, whereas hydrolysis to hydroxyatrazine

Isotope-based immunological techniques. Their use in assessment of immune competence and the study of immune responses to pathogens

International Nuclear Information System (INIS)

Duffus, W.P.H.

1984-01-01

The influence of isotope-based techniques on both assessment of immune competence and immune response to pathogens is discussed. Immunodeficiencies acquired as a result of factors like malnutrition and concomitant disease can severely affect not only attempts to intensify and improve production but also successful immune response against important vaccines such as rinderpest and foot-and-mouth disease. Isotope-based techniques, with their accuracy, speed and small sample volume, are ideally suited for assessing immunocompetence. One of the main drawbacks remains antigen purity, an area where research should now be concentrated. Lymphocyte transformation is widely used to assess cell-mediated immuno-competence but techniques to assess biological functions such as phagocytosis and cell-mediated cytotoxicity could more usefully reflect immune status. These latter techniques utilize isotopes such as 3 H, 14 C, 32 P and 125 I. Investigation of specific cell-mediated immune response often requires a labelled target. Suitable isotopes such as 51 Cr, 99 Tcsup(m), 75 Se and 3 H are compared for their capacity to label both mammalian and parasite targets. Suggestions are made on a number of areas of research that might usefully be encouraged and supported in order to improve applied veterinary immunology in tropical countries. (author)

Assessment of Bacterial Degradation of Aromatic Hydrocarbons in the Environment by Analysis of Stable Carbon Isotope Fractionation

Energy Technology Data Exchange (ETDEWEB)

Meckenstock, Rainer U. [Eberhard-Karls University of Tuebingen, Center for Applied Geoscience (Germany)], E-mail: rainer.meckenstock@uni-tuebingen.de; Morasch, Barbara [University of Konstanz, Faculty of Biology (Germany); Kaestner, Matthias; Vieth, Andrea; Richnow, Hans Hermann [Center for Environmental Research, Department of Remediation Research (Germany)

2002-05-15

{sup 13}C/{sup 12}C stable carbon isotope fractionation was used to assess biodegradation in contaminated aquifers with toluene as a model compound. Different strains of anaerobic bacteria (Thauera aromatica, Geobacter metallireducens, and the sulfate-reducing strain TRM1) showed consistent {sup 13}C/{sup 12}C carbon isotope fractionation with fractionation factors between {alpha}C = 1.0017 and 1.0018. In contrast, three cultures of aerobic organisms, using different mono- and dioxygenase enzyme systems to initiate toluene degradation, showed variable isotope fractionation factors of {alpha}C = 1.0027 (Pseudomonasputida strain mt-2), {alpha}C = 1.0011 (Ralstonia picketii), and{alpha}C = 1.0004 (Pseudomonas putida strain F1). The great variability of isotope fractionation between different aerobic bacterial strains suggests that interpretation of isotope data in oxic habitats can only be qualitative. A soil column was run as a model system for contaminated aquifers with toluene as the carbon source and sulfate as the electron acceptor and samples were taken at different ports along the column. Microbial toluene degradation was calculated based on the {sup 13}C/{sup 12}C isotope fractionation factors of the batch culture experiments together with the observed {sup 13}C/{sup 12}C isotope shifts of the residual toluene fractions. The calculated percentage of biodegradation, B, correlated well with the decreasing toluene concentrations at the sampling ports and indicated the increasing extent of biodegradation along the column. The theoretical toluene concentrations as calculated based on the isotope values matched the measured concentrations at the different sampling ports indicating that the Rayleigh equation can be used to calculate biodegradation in quasi closed systems based on measured isotope shifts. A similar attempt was performed to assess toluene degradation in a contaminated, anoxic aquifer. A transect of groundwater wells was monitored along the main

Intrusion resistant underground structure (IRUS) - safety assessment and licensing

International Nuclear Information System (INIS)

Lange, B. A.

1997-01-01

This paper describes the safety goals, human exposure scenarios and critical groups, the syvac-nsure performance assessment code, groundwater pathway safety results, and inadvertent human intrusion of the IRUS. 2 tabs

Safety assessment of complex engineered and natural systems: radioactive waste disposal

International Nuclear Information System (INIS)

McNeish, J.A.; Vallikat, V.; Atkins, J.; Balady, M.A.

1997-01-01

Evaluation of deep, geologic disposal of nuclear waste requires the probabilistic safety assessment of a complex system from the coupling of various processes and sub-systems, parameter and model uncertainties, spatial and temporal variabilities, and the multiplicity of designs and scenarios. Both the engineered and natural system are included in the evaluation. Each system has aspects with considerable uncertainty both in important parameters and in overall conceptual models. The study represented herein provides a probabilistic safety assessment of a potential respository system for multiple engineered barrier system (EBS) design and conceptual model configurations (CRWMS M and O, 1996a) and considers the effects of uncertainty on the overall results. The assessment is based on data and process models available at the time of the study and doesnt necessarily represent the current safety evaluation. In fact, the percolation flux through the repository system is now expected to be higher than the estimate used for this study. The potential effects of higher percolation fluxes are currently under study. The safety of the system was assessed for both 10,000 and 1,000,000 years. Use of alternative conceptual models also produced major improvement in safety. For example, use of a more realistic engineered system release model produced improvement of over an order of magnitude in safety. Alternative measurement locations for the safety assessment produced substantial increases in safety, through the results are based on uncertain dilution factors in the transporting groundwater. (Author)

Safety Culture Perceptions in a Collegiate Aviation Program: A Systematic Assessment

OpenAIRE

Adjekum, Daniel Kwasi

2014-01-01

An assessment of the perceptions of respondents on the safety culture at an accredited Part 141 four year collegiate aviation program was conducted as part of the implementation of a safety management system (SMS). The Collegiate Aviation Program Safety Culture Assessment Survey (CAPSCAS), which was modified and revalidated from the existing Commercial Aviation Safety Survey (CASS), was used. Participants were drawn from flight students and certified flight instructors in the program. The sur...

Analysis of dissolved organic carbon concentration and 13C isotopic signature by TOC-IRMS - assessment of analytical performance

Science.gov (United States)

Kirkels, Frédérique; Cerli, Chiara; Federherr, Eugen; Kalbitz, Karsten

2013-04-01

Stable carbon isotopes provide a powerful tool to assess carbon pools and their dynamics. Dissolved organic carbon (DOC) has been recognized to play an important role in ecosystem functioning and carbon cycling and has therefore gained increased research interest. However, direct measurement of 13C isotopic signature of carbon in the dissolved phase is technically challenging particularly using high temperature combustion. Until recently, mainly custom-made systems existed which were modified for coupling of TOC instruments with IRMS for simultaneous assessment of C content and isotopic signature. The variety of coupled systems showed differences in their analytical performances. For analysis of DOC high temperature combustion is recognized as best performing method, owing to its high efficiency of conversion to CO2 also for highly refractory components (e.g. humic, fulvic acids) present in DOC and soil extracts. Therefore, we tested high temperature combustion TOC coupled to IRMS (developed by Elementar Group) for bulk measurements of DOC concentration and 13C signature. The instruments are coupled via an Interface to exchange the carrier gas from O2 to He and to concentrate the derived CO2 for the isotope measurement. Analytical performance of the system was assessed for a variety of organic compounds characterized by different stability and complexity, including humic acid and DOM. We tested injection volumes between 0.2-3 ml, thereby enabling measurement of broad concentration ranges. With an injection volume of 0.5 ml (n=3, preceded by 1 discarded injection), DOC and 13C signatures for concentrations between 5-150 mg C/L were analyzed with high precision (standard deviation (SD) predominantly TOC-IRMS in comparison with other systems capable of determining C concentration and isotopic signatures. We recognize the advantages of this system providing: - High sample throughput, short measurement time (15 minutes), flexible sample volume - Easy maintenance

Role and meaning of safety assessment from the point of view of IAEA

International Nuclear Information System (INIS)

Lyubarskiy, A.

2012-01-01

In 2006, the IAEA published its revised Safety Fundamentals. This states that the ''fundamental safety objective is to protect people and the environment from harmful effects of ionizing radiation''. This objective has to be achieved for all facilities and activities and for all stages over the lifetime of a facility by adherence to ten fundamental principles. This leads, inter alia, to the requirement for a safety assessment to be carried out. In particular, the text accompanying Principle 3 on leadership and management for safety states that: ''3.15. Safety has to be assessed for all facilities and activities, consistent with a graded approach. Safety assessment involves the systematic analysis of normal operation and its effects, of the ways in which failures might occur and of the consequences of such failures. Safety assessments cover the safety measures necessary to control the hazard, and the design and engineered safety features are assessed to demonstrate that they fulfill the safety functions required of them. Where control measures or operator actions are called on to maintain safety, an initial safety assessment has to be carried out to demonstrate that the arrangements made are robust and that they can be relied on. A facility may only be constructed and commissioned or an activity may only be commenced once it has been demonstrated to the satisfaction of the regulatory body that the proposed safety measures are adequate.'' Principle 3 further states that the process of safety assessment for facilities and activities is repeated in the conduct of operations in order to take into account changed circumstances (such as the application of new standards or scientific and technological developments), the feedback of operating experience, modifications and the effects of ageing. Continuation of operations over long periods of time requires reassessments demonstrating that the safety measures remain adequate. (orig.)

Methodology for Safety Assessment Applied to Predisposal Waste Management. Report of the Results of the International Project on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) 2004–2010)

International Nuclear Information System (INIS)

2015-12-01

Report of the Results of the International Project on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) (2004–2010) The IAEA’s progamme on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) focused on approaches and mechanisms for application of safety assessment methodologies for the predisposal management of radioactive waste. The initial outcome of the SADRWMS Project was achieved through the development of flowcharts, which have since been incorporated into IAEA Safety Standards Series No. GSG-3, Safety Case and Safety Assessment for Predisposal Management of Radioactive Waste. In 2005, an initial specification was developed for the Safety Assessment Framework (SAFRAN) software tool to apply the SADRWMS flowcharts. In 2008, an in-depth application of the SAFRAN tool and the SADRWMS methodology was carried out on the predisposal management facilities of the Thailand Institute of Nuclear Technology Radioactive Waste Management Centre (TINT Facility). This publication summarizes the content and outcomes of the SADRWMS programme. The Chairman’s Report of the SADRWMS Project and the Report of the TINT test case are provided on the CD-ROM which accompanies this report

Safety assessment of human and organizational factors in French fuel cycle facilities

International Nuclear Information System (INIS)

Menuet, Lise; Beauquier, Sophie

2013-01-01

According to the French law, each nuclear facility has to provide a safety demonstration every ten years. The assessment of this demonstration supports the decision of the French Safety Authority regarding the authorisation of operating for the ten years to come. In addition, transversal topics, which are linked with safety performance, such as safety management, management of competencies, maintenance's policy are periodically evaluated. One aspect of these assessments relates to Human and Organizational Factors (HOF) and their contribution to safety. Our communication will describe the assessment of the HOF-related part, performed by the Institute for Radioprotection and Nuclear Safety Institute (IRSN) the Technical Support Organisation of the French Safety Authority). It will focus on the methodological framework, the tools which are developed and used for assessing the integration of HOF in safety demonstration, and the main difficulties of this kind of assessment. Each situation will be illustrated by concrete examples coming from safety assessments concerning fuel cycle's plants: Areva's plants dedicated to uranium conversion, uranium enrichment, fuel manufacturing, spent fuel reprocessing, treatment facilities and CEA's laboratories dedicated to research and development and to interim spent fuel storage. The methodological framework for assessing HOF currently implements three main steps which will be precisely described: - checking that the nuclear plant has made an exhaustive analysis of the risks linked with HOF. Regarding to HOF, the Licensee safety demonstration is based on the description of the main human activities which are considered as hazardous regarding safety. These activities are accomplished with a human contribution and they require a safe realisation. - assessing the human, organisational and technical barriers that the nuclear plant have planed in order to make the operations safe, to avoid, prevent or detect an

POSSIBILITY OF USING CARBON ISOTOPES IN THE ASSESSMENT OF THE POLLUTION OF GAS PHASE IN ENVIRONMENTAL RESEARCH

Directory of Open Access Journals (Sweden)

Dorota Porowska

2015-10-01

Full Text Available Carbon isotope analyses can be used for knowledge and practical purpose. They can be used to assess the genesis of carbon in geochemical environment, and may also be used to indicate environmental contamination by carbon-containing compounds. The aim of the paper is to indicate the possibilities of using carbon isotope composition for interpretation concerning the following elements of the natural environment: atmospheric air, subsurface zone (gases in soils and aeration zone in terms of natural and anthropogenic factors influencing on their quality. This method can be applied universally, when carbon sources are different in isotopic composition.

Economic aspects of risk assessment in chemical safety

Energy Technology Data Exchange (ETDEWEB)

Drummond, M F; Shannon, H S

1986-05-01

This paper considers how the economic aspects of risk assessment in chemical safety can be strengthened. Its main focus is on how economic appraisal techniques, such as cost-benefit and cost-effectiveness analysis, can be adapted to the requirements of the risk-assessment process. Following a discussion of the main methodological issues raised by the use of economic appraisal, illustrated by examples from the health and safety field, a number of practical issues are discussed. These include the consideration of the distribution of costs, effects and benefits, taking account of uncertainty, risk probabilities and public perception, making the appraisal techniques useful to the early stages of the risk-assessment process and structuring the appraisal to permit continuous feedback to the participants in the risk-assessment process. It is concluded that while the way of thinking embodied in economic appraisal is highly relevant to the consideration of choices in chemical safety, the application of these principles in formal analysis of risk reduction procedures presents a more mixed picture. The main suggestions for improvement in the analyses performed are the undertaking of sensitivity analyses of study results to changes in the key assumptions, the presentation of the distribution of costs and benefits by viewpoint, the comparison of health and safety measures in terms of their incremental cost per life-year (or quality-adjusted life-year) gained and the more frequent retrospective review and revision of the economic analyses that are undertaken.

The role of probabilistic safety assessment in the design

International Nuclear Information System (INIS)

Green, A.; Ingham, E.L.

1989-01-01

The use of probabilistic safety assessment (PSA) for Heysham 2 and Torness marked a major change in the design approach to nuclear safety within the U.K. Design Safety Guidelines incorporating probabilistic safety targets required that design justification would necessitate explicit consideration of the consequence of accidents in relation to their frequency. The paper discusses these safety targets and their implications, the integration of PSA into the design process and an outline of the methodology. The influence of PSA on the design is discussed together with its role in the overall demonstration of reactor safety. (author)

Procedures for conducting probabilistic safety assessment for non-reactor nuclear facilities

International Nuclear Information System (INIS)

2002-01-01

A well performed and adequately documented safety assessment of a nuclear facility will serve as a basis to determine whether the facility complies with the safety objectives, principles and criteria as stipulated by the national regulatory body of the country where the facility is in operation. International experience shows that the practices and methodologies used to perform safety assessments and periodic safety re-assessment for non-reactor nuclear facilities differ significantly from county to country. Most developing countries do not have methods and guidance for safety assessment that are prescribed by the regulatory body. Typically the safety evaluation for the facility is based on a case by case assessment. Whilst conservative deterministic analyses are predominantly used as a licensing basis in many countries, recently probabilistic safety assessment (PSA) techniques have been applied as a useful complementary tool to support safety decision making. The main benefit of PSA is to provide insights into the safety aspects of facility design and operation. PSA points up the potential environmental impacts of postulated accidents, including the dominant risk contributors, and enables safety analysts to compare options for reducing risk. In order to advise on how to apply PSA methodology for the safety assessment of non-reactor nuclear facilities, the IAEA organized several consultants meetings, which led to the preparation of this TECDOC. This document is intended as guidance for the conduct of PSA in non-nuclear facilities. The main emphasis here is on the general procedural steps of a PSA that is specific for a non-reactor nuclear facility, rather than the details of the specific methods. The report is directed at technical staff managing or performing such probabilistic assessments and to promote a standardized framework, terminology and form of documentation for these PSAs. It is understood that the level of detail implied in the tasks presented in this

Selected component failure rate values from fusion safety assessment tasks

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, L.C.

1998-09-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers.

Selected Component Failure Rate Values from Fusion Safety Assessment Tasks

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, Lee Charles

1998-09-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers.

Selected component failure rate values from fusion safety assessment tasks

International Nuclear Information System (INIS)

Cadwallader, L.C.

1998-01-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers

Parameter study on Japanese proposal of ITER hydrogen isotope separation system

International Nuclear Information System (INIS)

Yoshida, Hiroshi; Enoeda, Mikio; Tanaka, Shigeru; Ohokawa, Yoshinao; Ohara, Atsushi; Nagakura, Masaaki; Naito, Taisei; Nagashima, Kazuhiro.

1991-01-01

As part of Japanese design contribution in the ITER activity, conceptual design of an entire ITER tritium system and their safety analysis have been carried out through the three-year period since 1988. The tritium system includes the following subsystems; - Fuelling (gas puffing and pellet injection) subsystem, - Torus vacuum pumping subsystem, - Plasma exhaust gas purification subsystem, - Hydrogen isotope separation subsystem, - NBI gas processing subsystem, - Blanket tritium recovery subsystem, - Tritiated water processing subsystem, - Tritium safety subsystem. Hydrogen isotope separation system is a key subsystem in the ITER tritium system because it is connected to all above subsystems. This report describes an analytical study on the Japanese concept of hydrogen isotope separation system. (author)

Safety Assessment of Talc as Used in Cosmetics.

Science.gov (United States)

Fiume, Monice M; Boyer, Ivan; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2015-01-01

The Cosmetic Ingredient Review Expert Panel (Panel) assessed the safety of talc for use in cosmetics. The safety of talc has been the subject of much debate through the years, partly because the relationship between talc and asbestos is commonly misunderstood. Industry specifications state that cosmetic-grade talc must contain no detectable fibrous, asbestos minerals. Therefore, the large amount of available animal and clinical data the Panel relied on in assessing the safety of talc only included those studies on talc that did not contain asbestos. The Panel concluded that talc is safe for use in cosmetics in the present practices of use and concentration (some cosmetic products are entirely composed of talc). Talc should not be applied to the skin when the epidermal barrier is missing or significantly disrupted. © The Author(s) 2015.

Environment, safety and health progress assessment manual

International Nuclear Information System (INIS)

1992-12-01

On June 27, 1989, the Secretary of Energy announced a 10-Point Initiative to strengthen environment, safety, and health (ES ampersand H) programs, and waste management activities at DOE production, research, and testing facilities. One of the points involved conducting dent Tiger Team Assessments of DOE operating facilities. The Office of Special independent Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This manual documents the processes to be used to perform the ES ampersand H Progress Assessments. It was developed based upon the lessons learned from Tiger Team Assessments, the two pilot Progress Assessments, and Progress Assessments that have been completed. The manual will be updated periodically to reflect lessons learned or changes in policy

On the fundamentals of nuclear reactor safety assessment. Inherent threats and their implications

Energy Technology Data Exchange (ETDEWEB)

Hyvaerinen, J. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland). Nuclear Safety Dept.

1996-12-01

The thesis addresses some fundamental questions related to implementation and assessment of nuclear safety. The safety principles and assessment methods are described, followed by descriptions of selected novel technical challenges to nuclear safety. The novel challenges encompass a wide variety of technical issues, thus providing insights on the limitations of conventional safety assessment methods. Study of the limitations suggests means to improve nuclear reactor design criteria and safety assessment practices. The novel safety challenges discussed are (1) inherent boron dilution in PWRs, (2) metallic insulation performance with respect to total loss of emergency cooling systems in a loss-of-coolant accident, and (3) horizontal steam generator heat transfer performance at natural circulation conditions. (50 refs.).

On the fundamentals of nuclear reactor safety assessment. Inherent threats and their implications

International Nuclear Information System (INIS)

Hyvaerinen, J.

1996-12-01

The thesis addresses some fundamental questions related to implementation and assessment of nuclear safety. The safety principles and assessment methods are described, followed by descriptions of selected novel technical challenges to nuclear safety. The novel challenges encompass a wide variety of technical issues, thus providing insights on the limitations of conventional safety assessment methods. Study of the limitations suggests means to improve nuclear reactor design criteria and safety assessment practices. The novel safety challenges discussed are (1) inherent boron dilution in PWRs, (2) metallic insulation performance with respect to total loss of emergency cooling systems in a loss-of-coolant accident, and (3) horizontal steam generator heat transfer performance at natural circulation conditions. (50 refs.)

Assessment of Safety Standards for Automotive Electronic Control Systems

Science.gov (United States)

2016-06-01

This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

Plasma-safety assessment model and safety analyses of ITER

International Nuclear Information System (INIS)

Honda, T.; Okazaki, T.; Bartels, H.-H.; Uckan, N.A.; Sugihara, M.; Seki, Y.

2001-01-01

A plasma-safety assessment model has been provided on the basis of the plasma physics database of the International Thermonuclear Experimental Reactor (ITER) to analyze events including plasma behavior. The model was implemented in a safety analysis code (SAFALY), which consists of a 0-D dynamic plasma model and a 1-D thermal behavior model of the in-vessel components. Unusual plasma events of ITER, e.g., overfueling, were calculated using the code and plasma burning is found to be self-bounded by operation limits or passively shut down due to impurity ingress from overheated divertor targets. Sudden transition of divertor plasma might lead to failure of the divertor target because of a sharp increase of the heat flux. However, the effects of the aggravating failure can be safely handled by the confinement boundaries. (author)

Computer analyses for the design, operation and safety of new isotope production reactors: A technology status review

International Nuclear Information System (INIS)

Wulff, W.

1990-01-01

A review is presented on the currently available technologies for nuclear reactor analyses by computer. The important distinction is made between traditional computer calculation and advanced computer simulation. Simulation needs are defined to support the design, operation, maintenance and safety of isotope production reactors. Existing methods of computer analyses are categorized in accordance with the type of computer involved in their execution: micro, mini, mainframe and supercomputers. Both general and special-purpose computers are discussed. Major computer codes are described, with regard for their use in analyzing isotope production reactors. It has been determined in this review that conventional systems codes (TRAC, RELAP5, RETRAN, etc.) cannot meet four essential conditions for viable reactor simulation: simulation fidelity, on-line interactive operation with convenient graphics, high simulation speed, and at low cost. These conditions can be met by special-purpose computers (such as the AD100 of ADI), which are specifically designed for high-speed simulation of complex systems. The greatest shortcoming of existing systems codes (TRAC, RELAP5) is their mismatch between very high computational efforts and low simulation fidelity. The drift flux formulation (HIPA) is the viable alternative to the complicated two-fluid model. No existing computer code has the capability of accommodating all important processes in the core geometry of isotope production reactors. Experiments are needed (heat transfer measurements) to provide necessary correlations. It is important for the nuclear community, both in government, industry and universities, to begin to take advantage of modern simulation technologies and equipment. 41 refs

Safety assessment for the above ground storage of Cadmium Safety and Control Rods at the Solid Waste Management Facility

International Nuclear Information System (INIS)

Shaw, K.W.

1993-11-01

The mission of the Savannah River Site is changing from radioisotope production to waste management and environmental restoration. As such, Reactor Engineering has recently developed a plan to transfer the safety and control rods from the C, K, L, and P reactor disassembly basin areas to the Transuranic (TRU) Waste Storage Pads for long-term, retrievable storage. The TRU pads are located within the Solid Waste Management Facilities at the Savannah River Site. An Unreviewed Safety Question (USQ) Safety Evaluation has been performed for the proposed disassembly basin operations phase of the Cadmium Safety and Control Rod Project. The USQ screening identified a required change to the authorization basis; however, the Proposed Activity does not involve a positive USQ Safety Evaluation. A Hazard Assessment for the Cadmium Safety and Control Rod Project determined that the above-ground storage of the cadmium rods results in no change in hazard level at the TRU pads. A Safety Assessment that specifically addresses the storage (at the TRU pads) phase of the Cadmium Safety and Control Rod Project has been performed. Results of the Safety Assessment support the conclusion that a positive USQ is not involved as a result of the Proposed Activity

Review and assessment of nuclear facilities by the regulatory body. Safety guide

International Nuclear Information System (INIS)

2004-01-01

The purpose of this Safety Guide is to provide recommendations for regulatory bodies on reviewing and assessing the various safety related submissions made by the operator of a nuclear facility at different stages (siting, design, construction, commissioning, operation and decommissioning or closure) in the facility's lifetime to determine whether the facility complies with the applicable safety objectives and requirements. This Safety Guide covers the review and assessment of submissions in relation to the safety of nuclear facilities such as: enrichment and fuel manufacturing plants. Nuclear power plants. Other reactors such as research reactors and critical assemblies. Spent fuel reprocessing plants. And facilities for radioactive waste management, such as treatment, storage and disposal facilities. This Safety Guide also covers issues relating to the decommissioning of nuclear facilities, the closure of waste disposal facilities and site rehabilitation. Objectives, management, planning and organizational matters relating to the review and assessment process are presented in Section 2. Section 3 deals with the bases for decision making and conduct of the review and assessment process. Section 4 covers aspects relating to the assessment of this process. The Appendix provides a generic list of topics to be covered in the review and assessment process

Review and assessment of nuclear facilities by the regulatory body. Safety guide

International Nuclear Information System (INIS)

2005-01-01

The purpose of this Safety Guide is to provide recommendations for regulatory bodies on reviewing and assessing the various safety related submissions made by the operator of a nuclear facility at different stages (siting, design, construction, commissioning, operation and decommissioning or closure) in the facility's lifetime to determine whether the facility complies with the applicable safety objectives and requirements. This Safety Guide covers the review and assessment of submissions in relation to the safety of nuclear facilities such as: enrichment and fuel manufacturing plants. Nuclear power plants. Other reactors such as research reactors and critical assemblies. Spent fuel reprocessing plants. And facilities for radioactive waste management, such as treatment, storage and disposal facilities. This Safety Guide also covers issues relating to the decommissioning of nuclear facilities, the closure of waste disposal facilities and site rehabilitation. Objectives, management, planning and organizational matters relating to the review and assessment process are presented in Section 2. Section 3 deals with the bases for decision making and conduct of the review and assessment process. Section 4 covers aspects relating to the assessment of this process. The Appendix provides a generic list of topics to be covered in the review and assessment process

Safety assessment guidance in the International Atomic Energy Agency RADWASS Program

Energy Technology Data Exchange (ETDEWEB)

Vovk, I.F.; Seitz, R.R.

1995-12-31

The IAEA RADWASS programme is aimed at establishing a coherent and comprehensive set of principles and standards for the safe management of waste and formulating the guidelines necessary for their application. A large portion of this programme has been devoted to safety assessments for various waste management activities. Five Safety Guides are planned to be developed to provide general guidance to enable operators and regulators to develop necessary framework for safety assessment process in accordance with international recommendations. They cover predisposal, near surface disposal, geological disposal, uranium/thorium mining and milling waste, and decommissioning and environmental restoration. The Guide on safety assessment for near surface disposal is at the most advanced stage of preparation. This draft Safety Guide contains guidance on description of the disposal system, development of a conceptual model, identification and description of relevant scenarios and pathways, consequence analysis, presentation of results and confidence building. The set of RADWASS publications is currently undergoing in-depth review to ensure a harmonized approach throughout the Safety Series.

Uncertainty in safety : new techniques for the assessment and optimisation of safety in process industry

NARCIS (Netherlands)

Rouvroye, J.L.; Nieuwenhuizen, J.K.; Brombacher, A.C.; Stavrianidis, P.; Spiker, R.Th.E.; Pyatt, D.W.

1995-01-01

At this moment there is no standardised method for the assessment for safety in the process industry. Many companies and institutes use qualitative techniques for safety analysis while other companies and institutes use quantitative techniques. The authors of this paper will compare different

Nuclear utility self-assessment as viewed by the corporate nuclear safety committee

International Nuclear Information System (INIS)

Corcoran, W.R.

1992-01-01

This paper discusses how corporate nuclear safety committees use the principles of self-assessment to enhance nuclear power plant safety performance. Corporate nuclear safety committees function to advise the senior nuclear power executive on matters affecting nuclear safety. These committees are required by the administrative controls section of the plant technical specifications which are part of the final safety analysis report and the operating license. Committee membership includes senior utility executives, executives from sister utilities, utility senior technical experts, and outside consultants. Current corporate nuclear safety committees often have a finely tuned intuitive feel for self-assessment that they use to probe the underlying opportunities for quality and safety enhancements. The questions prompted by the self-assessment orientation enable the utility line organization members to gain better perspectives on the characteristics of the organizational systems that they manage and work in

Quantitative reliability assessment for safety critical system software

International Nuclear Information System (INIS)

Chung, Dae Won; Kwon, Soon Man

2005-01-01

An essential issue in the replacement of the old analogue I and C to computer-based digital systems in nuclear power plants is the quantitative software reliability assessment. Software reliability models have been successfully applied to many industrial applications, but have the unfortunate drawback of requiring data from which one can formulate a model. Software which is developed for safety critical applications is frequently unable to produce such data for at least two reasons. First, the software is frequently one-of-a-kind, and second, it rarely fails. Safety critical software is normally expected to pass every unit test producing precious little failure data. The basic premise of the rare events approach is that well-tested software does not fail under normal routine and input signals, which means that failures must be triggered by unusual input data and computer states. The failure data found under the reasonable testing cases and testing time for these conditions should be considered for the quantitative reliability assessment. We will present the quantitative reliability assessment methodology of safety critical software for rare failure cases in this paper

Safety assessment of botanicals and botanical preparations used as ingredients in food supplements: testing an European Food Safety Authority-tiered approach.

Science.gov (United States)

Speijers, Gerrit; Bottex, Bernard; Dusemund, Birgit; Lugasi, Andrea; Tóth, Jaroslav; Amberg-Müller, Judith; Galli, Corrado L; Silano, Vittorio; Rietjens, Ivonne M C M

2010-02-01

This article describes results obtained by testing the European Food Safety Authority-tiered guidance approach for safety assessment of botanicals and botanical preparations intended for use in food supplements. Main conclusions emerging are as follows. (i) Botanical ingredients must be identified by their scientific (binomial) name, in most cases down to the subspecies level or lower. (ii) Adequate characterization and description of the botanical parts and preparation methodology used is needed. Safety of a botanical ingredient cannot be assumed only relying on the long-term safe use of other preparations of the same botanical. (iii) Because of possible adulterations, misclassifications, replacements or falsifications, and restorations, establishment of adequate quality control is necessary. (iv) The strength of the evidence underlying concerns over a botanical ingredient should be included in the safety assessment. (v) The matrix effect should be taken into account in the safety assessment on a case-by-case basis. (vi) Adequate data and methods for appropriate exposure assessment are often missing. (vii) Safety regulations concerning toxic contaminants have to be complied with. The application of the guidance approach can result in the conclusion that safety can be presumed, that the botanical ingredient is of safety concern, or that further data are needed to assess safety.

Measuring Best Practices for Workplace Safety, Health, and Well-Being: The Workplace Integrated Safety and Health Assessment.

Science.gov (United States)

Sorensen, Glorian; Sparer, Emily; Williams, Jessica A R; Gundersen, Daniel; Boden, Leslie I; Dennerlein, Jack T; Hashimoto, Dean; Katz, Jeffrey N; McLellan, Deborah L; Okechukwu, Cassandra A; Pronk, Nicolaas P; Revette, Anna; Wagner, Gregory R

2018-05-01

To present a measure of effective workplace organizational policies, programs, and practices that focuses on working conditions and organizational facilitators of worker safety, health and well-being: the workplace integrated safety and health (WISH) assessment. Development of this assessment used an iterative process involving a modified Delphi method, extensive literature reviews, and systematic cognitive testing. The assessment measures six core constructs identified as central to best practices for protecting and promoting worker safety, health and well-being: leadership commitment; participation; policies, programs, and practices that foster supportive working conditions; comprehensive and collaborative strategies; adherence to federal and state regulations and ethical norms; and data-driven change. The WISH Assessment holds promise as a tool that may inform organizational priority setting and guide research around causal pathways influencing implementation and outcomes related to these approaches.

NASA Aviation Safety Program Systems Analysis/Program Assessment Metrics Review

Science.gov (United States)

Louis, Garrick E.; Anderson, Katherine; Ahmad, Tisan; Bouabid, Ali; Siriwardana, Maya; Guilbaud, Patrick

2003-01-01

The goal of this project is to evaluate the metrics and processes used by NASA's Aviation Safety Program in assessing technologies that contribute to NASA's aviation safety goals. There were three objectives for reaching this goal. First, NASA's main objectives for aviation safety were documented and their consistency was checked against the main objectives of the Aviation Safety Program. Next, the metrics used for technology investment by the Program Assessment function of AvSP were evaluated. Finally, other metrics that could be used by the Program Assessment Team (PAT) were identified and evaluated. This investigation revealed that the objectives are in fact consistent across organizational levels at NASA and with the FAA. Some of the major issues discussed in this study which should be further investigated, are the removal of the Cost and Return-on-Investment metrics, the lack of the metrics to measure the balance of investment and technology, the interdependencies between some of the metric risk driver categories, and the conflict between 'fatal accident rate' and 'accident rate' in the language of the Aviation Safety goal as stated in different sources.

Development of Safety Culture Assessment Strategy for Korean NPP

International Nuclear Information System (INIS)

Park, Jung Hwan; Kim, Jong Hyun

2014-01-01

This paper aims at developing the requirements for a method to evaluate the operational safety culture, evaluating currently available methods based on the requirements, and suggesting a method to evaluate and improve the operational safety culture for Korean nuclear power plants. This paper reviews the widely-used methods to assess safety culture for NPPs and their basis. Then, this paper develops the requirements for the method to evaluate operational safety culture for Korean NPPs. Based on these requirements, Korean Safety Culture Indicators (KSCI) and evaluation measures are also suggested. Finally this paper proposes the guidelines to develop improvements to safety culture from the evaluation results

Development of Safety Culture Assessment Strategy for Korean NPP

Energy Technology Data Exchange (ETDEWEB)

Park, Jung Hwan; Kim, Jong Hyun [KEPCO, Ulsan (Korea, Republic of)

2014-08-15

This paper aims at developing the requirements for a method to evaluate the operational safety culture, evaluating currently available methods based on the requirements, and suggesting a method to evaluate and improve the operational safety culture for Korean nuclear power plants. This paper reviews the widely-used methods to assess safety culture for NPPs and their basis. Then, this paper develops the requirements for the method to evaluate operational safety culture for Korean NPPs. Based on these requirements, Korean Safety Culture Indicators (KSCI) and evaluation measures are also suggested. Finally this paper proposes the guidelines to develop improvements to safety culture from the evaluation results.

Institutionalization of safety re-assessment system for operating nuclear power plants

International Nuclear Information System (INIS)

Kim, H. J.; Cho, J. C.; Min, B. K.; Park, J. S.; Jung, H. D.; Oh, K. M.; Kim, W. K.; Lim, J. H.

1999-01-01

In this study, in-depth reviews of the foreign countries' experiences and practices in applications of the periodic safety review (PSR), backfitting and license renewal systems as well as the current status of nuclear power safety assurance programs and activities in Korea have been performed to investigate the necessity and feasibility of the application of the systems for the domestic operating nuclear power plants and to establish effective strategy and methodology for the institutionalization of a periodic safety re-assessment system appropriate to both the domestic and international nuclear power environments by incorporating the PSR with the backfitting and license renewal systems. For these purposes, the regulatory policy, fundamental principles and detailed requirements for the institutionalization of the safety re-assessment system and the effective measures for active implementation of the backfitting program have been developed and then a comparative study of benefits and shortcomings has been conducted for the three different models of the periodic safety re-assessment system incorporated with either the license renewal or life extension process, which have been considered as practicable ones in the domestic situation. The model chosen in this study as the most appropriate safety re-assessment system is the one that the re-assessments are performed at the interval of ten years throughout the service life of nuclear power plant and the ten-year license renewal or life extension after the expiration of design life can be permitted based on the regulatory review of the re-assessment results and follow-up measures. Finally, this paper has discussed on the details of the requirements, approach and procedures established for the institutionalization of the periodic safety re-assessment system chosen as the most appropriate one for domestic applications

Comparative assessment of safety indicators for vehicle trajectories on the highway

NARCIS (Netherlands)

Mullakkal Babu, F.A.; Wang, M.; Farah, H.; van Arem, B.; Happee, R.

2017-01-01

Safety measurement and analysis have been a challenging and well-researched topic in transportation. Conventionally, surrogate safety measures have been used as safety indicators in simulation models for safety assessment, in control formulations for driver assistance systems, and in data analysis

Establishment of database for radiation exposure and safety assessment

Energy Technology Data Exchange (ETDEWEB)

Choi, G. S.; Kim, J. H. [Science Culture Research Institute, Seoul (Korea, Republic of)

2005-12-15

The nuclear electric energy in our country plays a major role for the national industrial development as well as for the secure living of the peoples. It is, however, considered as a socially dreadful elements because of the radiation materials exposed into the environment. In effect, the DB is intended to serve for the reference to the epidemical study upon the low-level radiation exposure involving the nuclear facilities, radio-isotope business enterprises, and the related workers at the radiation sites. In connection with the development of nuclear energy, the low-level radiation, associated with the radioisotope materials exposed into our environment out of nuclear facilities, is believed to possibly raise significant hazardous effects toward human persons. Therefor, it is necessary to take a positive counter measures by means of comprehensive quantitative estimates on its possibilities. In consequence, the low-level radiation effects do not bring about the immediate hazard cases, however, appear to possibly pose the lately caused diseases such as cancer cause, life reduction, and creation of mutation, etc. Therefore, it is intended to set up the social security with the secure safety, by conducting an advanced safety study on the low-level radiation.

Establishment of database for radiation exposure and safety assessment

International Nuclear Information System (INIS)

Choi, G. S.; Kim, J. H.

2005-12-01

The nuclear electric energy in our country plays a major role for the national industrial development as well as for the secure living of the peoples. It is, however, considered as a socially dreadful elements because of the radiation materials exposed into the environment. In effect, the DB is intended to serve for the reference to the epidemical study upon the low-level radiation exposure involving the nuclear facilities, radio-isotope business enterprises, and the related workers at the radiation sites. In connection with the development of nuclear energy, the low-level radiation, associated with the radioisotope materials exposed into our environment out of nuclear facilities, is believed to possibly raise significant hazardous effects toward human persons. Therefor, it is necessary to take a positive counter measures by means of comprehensive quantitative estimates on its possibilities. In consequence, the low-level radiation effects do not bring about the immediate hazard cases, however, appear to possibly pose the lately caused diseases such as cancer cause, life reduction, and creation of mutation, etc. Therefore, it is intended to set up the social security with the secure safety, by conducting an advanced safety study on the low-level radiation

Safety assessment of Novi Han radioactive waste repository - features, problems, results and perspectives

International Nuclear Information System (INIS)

Mateeva, M.

2000-01-01

This paper summarizes the work done and the achievements reached in the Novi Han radioactive waste repository safety assessment within the IAEA Model Project 'Increasing the safety of Novi Han radioactive waste repository BUL 4/005'. The overall safety assessment has a wide context, but the work reported here relates only to some details and results concerning the development and implementation of the appropriate methodology approach, model and computer code used for the calculations. Different steps and procedures are included for a better practical understanding of the obtained results during the safety assessment performance. The methodology approach is widely based on an international experience in safety analysis and implemented for evaluation computer code AMBER, which is one of the recommended from the safety assessments experts. (author)

76 FR 74723 - New Car Assessment Program (NCAP); Safety Labeling

Science.gov (United States)

2011-12-01

... [Docket No. NHTSA 2010-0025] RIN 2127-AK51 New Car Assessment Program (NCAP); Safety Labeling AGENCY... NHTSA's regulation on vehicle labeling of safety rating information to reflect the enhanced NCAP ratings... Traffic Safety Administration under the enhanced NCAP testing and rating program. * * * * * (e) * * * (4...

Safety Assessment for Research Reactors and Preparation of the Safety Analysis Report. Specific Safety Guide

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-11-15

. The standards are also applied by regulatory bodies and operators around the world to enhance safety in nuclear power generation and in nuclear applications in medicine, industry, agriculture and research. Safety is not an end in itself but a prerequisite for the purpose of the protection of people in all States and of the environment - now and in the future. The risks associated with ionizing radiation must be assessed and controlled without unduly limiting the contribution of nuclear energy to equitable and sustainable development. Governments, regulatory bodies and operators everywhere must ensure that nuclear material and radiation sources are used beneficially, safely and ethically. The IAEA safety standards are designed to facilitate this, and I encourage all Member States to make use of them.

Safety Assessment for Research Reactors and Preparation of the Safety Analysis Report. Specific Safety Guide

International Nuclear Information System (INIS)

2011-01-01

. The standards are also applied by regulatory bodies and operators around the world to enhance safety in nuclear power generation and in nuclear applications in medicine, industry, agriculture and research. Safety is not an end in itself but a prerequisite for the purpose of the protection of people in all States and of the environment - now and in the future. The risks associated with ionizing radiation must be assessed and controlled without unduly limiting the contribution of nuclear energy to equitable and sustainable development. Governments, regulatory bodies and operators everywhere must ensure that nuclear material and radiation sources are used beneficially, safely and ethically. The IAEA safety standards are designed to facilitate this, and I encourage all Member States to make use of them.

Guidelines for the review research reactor safety. Reference document for IAEA Integrated Safety Assessment of Research Reactors (INSARR)

International Nuclear Information System (INIS)

1997-01-01

In 1992, the IAEA published new safety standards for research reactors as part of the set of publications considered by its Research Reactor Safety Programme (RRSP). This set also includes publications giving guidance for all safety aspects related to the lifetime of a research reactor. In addition, the IAEA has also revised the Safety Standards for radiation protection. Consequently, it was considered advisable to revise the Integrated Safety Assessment of Research Reactors (INSARR) procedures to incorporate the new requirements and guidance as well as to extend the scope of the safety reviews to currently operating research reactors. The present report is the result of this revision. The purpose of this report is to give guidance on the preparation, execution, reporting and follow-up of safety review mission to research reactors as conducted by the IAEA under its INSARR missions safety service. However, it will also be of assistance to operators and regulators in conducting: (a) ad hoc safety assessments of research reactors to address individual issues such as ageing or safety culture; and (b) other types of safety reviews such as internal and peer reviews and regulatory inspections

Data report for the safety assessment SR-Site

International Nuclear Information System (INIS)

2010-12-01

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Data report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Psychometric model for safety culture assessment in nuclear research facilities

Energy Technology Data Exchange (ETDEWEB)

Nascimento, C.S. do, E-mail: claudio.souza@ctmsp.mar.mil.br [Centro Tecnológico da Marinha em São Paulo (CTMSP), Av. Professor Lineu Prestes 2468, 05508-000 São Paulo, SP (Brazil); Andrade, D.A., E-mail: delvonei@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN – SP), Av. Professor Lineu Prestes 2242, 05508-000 São Paulo, SP (Brazil); Mesquita, R.N. de, E-mail: rnavarro@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN – SP), Av. Professor Lineu Prestes 2242, 05508-000 São Paulo, SP (Brazil)

2017-04-01

Highlights: • A psychometric model to evaluate ‘safety climate’ at nuclear research facilities. • The model presented evidences of good psychometric qualities. • The model was applied to nuclear research facilities in Brazil. • Some ‘safety culture’ weaknesses were detected in the assessed organization. • A potential tool to develop safety management programs in nuclear facilities. - Abstract: A safe and reliable operation of nuclear power plants depends not only on technical performance, but also on the people and on the organization. Organizational factors have been recognized as the main causal mechanisms of accidents by research organizations through USA, Europe and Japan. Deficiencies related with these factors reveal weaknesses in the organization’s safety culture. A significant number of instruments to assess the safety culture based on psychometric models that evaluate safety climate through questionnaires, and which are based on reliability and validity evidences, have been published in health and ‘safety at work’ areas. However, there are few safety culture assessment instruments with these characteristics (reliability and validity) available on nuclear literature. Therefore, this work proposes an instrument to evaluate, with valid and reliable measures, the safety climate of nuclear research facilities. The instrument was developed based on methodological principles applied to research modeling and its psychometric properties were evaluated by a reliability analysis and validation of content, face and construct. The instrument was applied to an important nuclear research organization in Brazil. This organization comprises 4 research reactors and many nuclear laboratories. The survey results made possible a demographic characterization and the identification of some possible safety culture weaknesses and pointing out potential areas to be improved in the assessed organization. Good evidence of reliability with Cronbach's alpha

Psychometric model for safety culture assessment in nuclear research facilities

International Nuclear Information System (INIS)

Nascimento, C.S. do; Andrade, D.A.; Mesquita, R.N. de

2017-01-01

Highlights: • A psychometric model to evaluate ‘safety climate’ at nuclear research facilities. • The model presented evidences of good psychometric qualities. • The model was applied to nuclear research facilities in Brazil. • Some ‘safety culture’ weaknesses were detected in the assessed organization. • A potential tool to develop safety management programs in nuclear facilities. - Abstract: A safe and reliable operation of nuclear power plants depends not only on technical performance, but also on the people and on the organization. Organizational factors have been recognized as the main causal mechanisms of accidents by research organizations through USA, Europe and Japan. Deficiencies related with these factors reveal weaknesses in the organization’s safety culture. A significant number of instruments to assess the safety culture based on psychometric models that evaluate safety climate through questionnaires, and which are based on reliability and validity evidences, have been published in health and ‘safety at work’ areas. However, there are few safety culture assessment instruments with these characteristics (reliability and validity) available on nuclear literature. Therefore, this work proposes an instrument to evaluate, with valid and reliable measures, the safety climate of nuclear research facilities. The instrument was developed based on methodological principles applied to research modeling and its psychometric properties were evaluated by a reliability analysis and validation of content, face and construct. The instrument was applied to an important nuclear research organization in Brazil. This organization comprises 4 research reactors and many nuclear laboratories. The survey results made possible a demographic characterization and the identification of some possible safety culture weaknesses and pointing out potential areas to be improved in the assessed organization. Good evidence of reliability with Cronbach's alpha

78 FR 14912 - International Aviation Safety Assessment (IASA) Program Change

Science.gov (United States)

2013-03-08

... Aviation Safety Assessment (IASA) Program Change AGENCY: Federal Aviation Administration (FAA), DOT. ACTION..., into the U.S., or codeshare with a U.S. air carrier, complies with international aviation safety... subject to that country's aviation safety oversight can serve the United States using its own aircraft or...

Fuel and canister process report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Werme, Lars; Lilja, Christina

2010-12-01

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Fuel and canister process report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Werme, Lars; Lilja, Christina (eds.)

2010-12-15

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Probabilistic safety assessment in radioactive waste disposal

International Nuclear Information System (INIS)

Robinson, P.C.

1987-07-01

Probabilistic safety assessment codes are now widely used in radioactive waste disposal assessments. This report gives an overview of the current state of the field. The relationship between the codes and the regulations covering radioactive waste disposal is discussed and the characteristics of current codes is described. The problems of verification and validation are considered. (author)

Assessment of Electrical Safety Beliefs and Practices: A Case Study

Directory of Open Access Journals (Sweden)

S. Boubaker

2017-12-01

Full Text Available In this paper, the electrical safety beliefs and practices in Hail region, Saudi Arabia, have been assessed. Based on legislative recommendations and rules applied in Saudi Arabia, on official statistics regarding the electricity-caused accidents and on the analysis of more than 200 photos captured in Hail (related to electrical safety, a questionnaire composed of 36 questions (10 for the respondents information, 16 for the home safety culture and 10 for the electrical devices purchasing culture has been devised and distributed to residents. 228 responses have been collected and analyzed. Using a scale similar to the one adopted for a university student GPA calculation, the electrical safety level (ESL in Hail region has been found to be 0.76 (in a scale of 4 points which is a very low score and indicates a poor electrical safety culture. Several recommendations involving different competent authorities have been proposed. Future work will concern the assessment of safety in industrial companies in Hail region.

Edible safety requirements and assessment standards for agricultural genetically modified organisms.

Science.gov (United States)

Deng, Pingjian; Zhou, Xiangyang; Zhou, Peng; Du, Zhong; Hou, Hongli; Yang, Dongyan; Tan, Jianjun; Wu, Xiaojin; Zhang, Jinzhou; Yang, Yongcun; Liu, Jin; Liu, Guihua; Li, Yonghong; Liu, Jianjun; Yu, Lei; Fang, Shisong; Yang, Xiaoke

2008-05-01

This paper describes the background, principles, concepts and methods of framing the technical regulation for edible safety requirement and assessment of agricultural genetically modified organisms (agri-GMOs) for Shenzhen Special Economic Zone in the People's Republic of China. It provides a set of systematic criteria for edible safety requirements and the assessment process for agri-GMOs. First, focusing on the degree of risk and impact of different agri-GMOs, we developed hazard grades for toxicity, allergenicity, anti-nutrition effects, and unintended effects and standards for the impact type of genetic manipulation. Second, for assessing edible safety, we developed indexes and standards for different hazard grades of recipient organisms, for the influence of types of genetic manipulation and hazard grades of agri-GMOs. To evaluate the applicability of these criteria and their congruency with other safety assessment systems for GMOs applied by related organizations all over the world, we selected some agri-GMOs (soybean, maize, potato, capsicum and yeast) as cases to put through our new assessment system, and compared our results with the previous assessments. It turned out that the result of each of the cases was congruent with the original assessment.

Safety assessment of emergency power systems for nuclear power plants

International Nuclear Information System (INIS)

1992-01-01

This publication is intended to assist the safety assessor within a regulatory body, or one working as a consultant, in assessing the safety of a given design of the emergency power systems (EPS) for a nuclear power plant. The present publication refers closely to the NUSS Safety Guide 50-SG-D7 (Rev. 1), Emergency Power Systems at Nuclear Power Plants. It covers therefore exactly the same technical subject as that Safety Guide. In view of its objective, however, it attempts to help in the evaluation of possible technical solutions which are intended to fulfill the safety requirements. Section 2 clarifies the scope further by giving an outline of the assessment steps in the licensing process. After a general outline of the assessment process in relation to the licensing of a nuclear power plant, the publication is divided into two parts. First, all safety issues are presented in the form of questions that have to be answered in order for the assessor to be confident of a safe design. The second part presents the same topics in tabulated form, listing the required documentation which the assessor has to consult and those international and national technical standards pertinent to the topics. An extensive reference list provides information on standards. 1 tab

Reactor Safety Assessment System--A situation assessment aid for USNRC emergency response

International Nuclear Information System (INIS)

Bray, M.A.; Sebo, D.E.; Dixon, B.W.

1985-01-01

The Reactor Safety Assessment System (RSAS) is an expert system under development for the United States Nuclear Regulatory Commission (USNRC). RSAS is intended for use at the NRC's Operations Center in the event of a serious incident at a licensed nuclear power plant. The system uses plant parameter data and status information from the power plant. It has a rule base that uses the parametric values, the known operator actions, and the time sequence information in the data to generate situation assessment conclusions for use by the NRC Reactor Safety Team. RSAS rules currently cover one specific reactor type and use setpoints specific to one power plant

Reactor Safety Assessment System: a situation assessment aid for USNRC emergency response

International Nuclear Information System (INIS)

Bray, M.A.; Sebo, D.E.; Dixon, B.W.

1985-04-01

The Reactor Safety Assessment System is an expert system under development for the United States Nuclear Regulatory Commission (NRC). RSAS is intended for use at the NRC's Operations Center in the event of a serious incident at a licensed nuclear power plant. The system uses plant parameter data and status information from the power plant. It has a rule base which uses the parametric values, the known operator actions and the time sequence information in the data to generate situation assessment conclusions for use by the NRC Reactor Safety Team. RSAS rules currently cover one specific reactor type and use setpoints specific to one power plant. 5 figs

[Safety assessment of foods derived from genetically modified plants].

Science.gov (United States)

Pöting, A; Schauzu, M

2010-06-01

The placing of genetically modified plants and derived food on the market falls under Regulation (EC) No. 1829/2003. According to this regulation, applicants need to perform a safety assessment according to the Guidance Document of the Scientific Panel on Genetically Modified Organisms of the European Food Safety Authority (EFSA), which is based on internationally agreed recommendations. This article gives an overview of the underlying legislation as well as the strategy and scientific criteria for the safety assessment, which should generally be based on the concept of substantial equivalence and carried out in relation to an unmodified conventional counterpart. Besides the intended genetic modification, potential unintended changes also have to be assessed with regard to potential adverse effects for the consumer. All genetically modified plants and derived food products, which have been evaluated by EFSA so far, were considered to be as safe as products derived from the respective conventional plants.

Refurbishment and safety upgradation of research reactor Cirus

International Nuclear Information System (INIS)

Marik, S.K.; Rao, D.V.H.; Bhatnagar, A.; Pant, R.C.; Tikku, A.C.; Sankar, S.

2006-01-01

Cirus, a 40 MW t, vertical tank type research reactor, having wide range of research facilities, was commissioned in the year 1960. This research reactor, situated at Mumbai, India has been operated and utilized extensively for isotope production, material testing and neutron beam research for nearly four decades. With a view to assess the residual life of the reactor, detailed ageing studies were carried out during the early 1990s. Based on these studies, refurbishment of Cirus for its life extension was taken up. During refurbishment, additional safety features were incorporated in various systems to qualify them for the current safety standards. This paper gives the details of the operating experiences, utilization of the reactor along with methodologies followed for carrying out detailed ageing studies, refurbishment and safety upgradation for its life extension

The Fukushima Daiichi Accident. Technical Volume 2/5. Safety Assessment

International Nuclear Information System (INIS)

2015-08-01

Technical Volume 1 of this report has described what happened during the accident at the Fukushima Daiichi nuclear power plant (NPP). This volume begins (Section 2.1) with a review of how the design basis of the site for external events was assessed initially and then reassessed over the life of the NPP. The section also describes the physical changes that were made to the units as a result. The remainder of the volume describes the treatment of beyond design basis events in the safety assessment of the site, the accident management provisions, the effectiveness of regulatory programmes, human and organizational factors and the safety culture, and the role of operating experience. Further background information is contained in three annexes included on the CD-ROM of this Technical Volume which describe analytical investigations of the accident along with information on topics such as system performance, defence in depth and severe accident phenomena. Section 2.2 provides an assessment of the systems that failed, resulting in a failure to maintain the fundamental safety functions in Units 1–3, which were in operation at the time of the tsunami and in which the reactor pressure vessels (RPV) and containment vessels failed. The section also describes Units 4-6, which were shut down at the time of the tsunami, and the site’s central spent fuel storage facility. Section 2.3 discusses the probabilistic and deterministic safety assessments of beyond design basis accidents (BDBAs) that had been performed for the plant and the insights from these assessments that had led to changes in the plant’s design. The section pays particular attention to the assessment of extreme natural hazards, such as the one which led to the total loss of AC power supply on the site. The additional loss of DC power supply in Units 1 and 2 played a key role in the progression of the accident because it impeded the diagnosis of plant conditions and made the operators unaware of the status of

Safety assessment of Vitis vinifera (grape)-derived ingredients as used in cosmetics.

Science.gov (United States)

Fiume, Monice M; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2014-01-01

The Cosmetic Ingredient Review Expert Panel (Panel) assessed the safety of 24 Vitis vinifera (grape)-derived ingredients and found them safe in the present practices of use and concentration in cosmetics. These ingredients function in cosmetics mostly as skin-conditioning agents, but some function as antioxidants, flavoring agents, and/or colorants. The Panel reviewed the available animal and clinical data to determine the safety of these ingredients. Additionally, some constituents of grapes have been assessed previously for safety as cosmetic ingredients by the Panel, and others are compounds that have been discussed in previous Panel safety assessments. © The Author(s) 2014.

Final Report to the Department of the Energy for Project Entitled Rare Isotope Science Assessment Committee

International Nuclear Information System (INIS)

Shapero, Donald; Meyer, Timothy I.

2007-01-01

The Rare Isotope Science Assessment Committee (RISAC) was convened by the National Research Council in response to an informal request from the DOE's Office of Nuclear Physics and the White House Office of Management and Budget. The charge to the committee is to examine and assess the broader scientific and international contexts of a U.S.-based rare-isotope facility. The committee met for the first time on December 16-17, 2005, in Washington, DC, and held three subsequent meetings. The committee's's final report was publicly released in unedited, prepublication form on Friday, December 8, 2006. The report was published in full-color by the National Academies Press in April 2007. Copies of the report were distributed to key decision makers and stakeholders around the world.

Self-assessment of safety culture in nuclear installations. Highlights and good practices

International Nuclear Information System (INIS)

2002-11-01

This report summarizes the findings of two IAEA Technical Committee Meetings on Safety Culture Self-Assessment Highlights and Good Practices. The meetings took place on 3-5 June 1998 and 23-25 October 2000 in Vienna, and involved an international cross-section of representatives who participated both in plenary discussions and working groups. The purpose of the meetings was to discuss the practical implications of evolutionary changes in the development of safety culture, and to share international experience, particularly on the methods used for the assessment of safety culture and good practices for its enhancement in an organization. The working groups were allocated specific topics for discussion, which included the following: organizational factors influencing the implementation of actions to improve safety culture; how to measure, effectively, progress in implementing solutions to safety culture problems; the symptoms of a weakening safety culture; the suitability of different methods for assessing safety culture; the achievement of sustainable improvements in safety culture using the results of assessment; the potential threats to the continuation of a strong safety culture in an organization from the many challenges facing the nuclear industry. The working groups, when appropriate, considered issues from both the utility's and the regulator's perspectives. This report will be of interest to all organizations who wish to assess and achieve a strong and sustainable safety culture. This includes not only nuclear power plants, but also other sectors of the nuclear industry such as uranium mines and mills, nuclear fuel fabrication facilities, nuclear waste repositories, research reactors, accelerators, radiography facilities, etc. The report specifically supplements other IAEA publications on this subject

A 2-year study of patient safety competency assessment in 29 clinical laboratories.

Science.gov (United States)

Reed, Robyn C; Kim, Sara; Farquharson, Kara; Astion, Michael L

2008-06-01

Competency assessment is critical for laboratory operations and is mandated by the Clinical Laboratory Improvement Amendments of 1988. However, no previous reports describe methods for assessing competency in patient safety. We developed and implemented a Web-based tool to assess performance of 875 laboratory staff from 29 laboratories in patient safety. Question categories included workplace culture, categorizing error, prioritization of patient safety interventions, strength of specific interventions, and general patient safety concepts. The mean score was 85.0%, with individual scores ranging from 56% to 100% and scores by category from 81.3% to 88.6%. Of the most difficult questions (laboratory technologists. Computer-based competency assessments help laboratories identify topics for continuing education in patient safety.

Reactor calculations in aid of isotope production at SAFARI-1

International Nuclear Information System (INIS)

Ball, G.

2003-01-01

Varying levels of reactor physics support is given to the isotope production industry. As the pressures on both the safety limits and economical production of reactor produced isotopes mount, reactor physics calculational support is playing an ever increasing role. Detailed modelling of the reactor, irradiation rigs and target material enables isotope production in reactors to be maximised with respect to yields and quality. NECSA's methodology in this field is described and some examples are given. (author)

South African safety assessment framework for the pebble bed modular reactor - HTR2008-58192

International Nuclear Information System (INIS)

Joubert, J.; Kohtz, N.; Coe, I.

2008-01-01

It is planned to construct a first of a kind Pebble Bed Modular Reactor (PBMR) in South Africa. A need has been recognized to accompany the licensing process for the PBMR with independent safety assessments to ensure that the safety case submitted by the applicant complies with the licensing requirements of the NNR. At the HTR 2006 Conference, the framework and major challenges on safety assessment that the South African National Nuclear Regulator (NNR) faces in developing and applying appropriate strategies and tools were presented. This paper discusses the current status of the various NNR assessment activities and describes how this will be considered in the NNR Final Report on the PBMR Safety Case. The traditional safety assessment process has been adapted to take into account the developmental nature of the project. By performing safety assessments, the designer and applicant must ensure that the design as proposed for construction and as-built meets the safety requirements defined by the regulatory framework. The regulator performs independent safety assessments, including independent analyses in areas deemed safety significant and potentially safety significant. The developmental nature of the project also led to the identification of a series of regulatory assessment activities preceding the formal assessment of the safety case. Besides an assessment of the resolution of Key Licensing Issues which have been defined in an early stage of the project and are discussed in /l/, these activities comprise the participation in an SAR Early Intervention Process, the execution of a regulatory HAZOP and the development of a regulatory assessment specification for the formal assessment of the safety case. This paper briefly describes these activities and their current status. During the last two years, significant progress was made with the development or adjustment of tools for the independent analysis by the regulator of the steady state core design, of the transient

Recent Trends In The Methods Of Safety Assessment Of Rad Waste Treatment And Disposal

International Nuclear Information System (INIS)

Mahmoud, N.S.

2012-01-01

Radioactive waste management system involves a huge variety of processes and activities. This includes; collection and segregation, pretreatment, treatment, conditioning, storage and finally disposal. To assure the safety of the different facility of each step in the waste management system, the operator should prepare a safety analysis report to be assessed by the national regulatory body. The content of the safety analysis report must include all data about the site, facility design, operational phase, waste materials, and safety assessment methodologies. Safety assessment methodologies are iterative processes involving site-specific, prospective modeling evaluations of the pre-operational, operational, and post-closure time in case of disposal facilities. The safety assessment focuses primarily on a decision about compliance with performance objectives, rather than the much more difficult problem of predicting actual radiological impacts on the public at far future times. The recent organization processes of the safety assessment are improved by the ISAM working group from IAEA for waste disposal site. These safety assessment methodologies have been modified within SADRWMS IAEA project for the establishment of safety methodologies for the pre-disposal facilities (treatment and storage facilities) and the disposal site.

Safety assessment of genetically modified foods

NARCIS (Netherlands)

Kleter, G.A.; Noordam, M.Y.

2016-01-01

The cultivation of genetically modified (GM) crops has steadily increased since their introduction to the market in the mid-1990s. Before these crops can be grown and sold they have to obtain regulatory approval in many countries, the process of which includes a pre-market safety assessment. The

Qualified Presumption of Safety (QPS) is a generic risk assessment approach applied by the European Food Safety Authority (EFSA)

DEFF Research Database (Denmark)

Leuschner, R. G. K.; Robinson, T. P.; Hugas, M.

2010-01-01

Qualified Presumption of Safety (QPS) is a generic risk assessment approach applied by the European Food Safety Authority (EFSA) to notified biological agents aiming at simplifying risk assessments across different scientific Panels and Units. The aim of this review is to outline the implementation...... and value of the QPS assessment for EFSA and to explain its principles such as the unambiguous identity of a taxonomic unit, the body of knowledge including potential safety concerns and how these considerations lead to a list of biological agents recommended for QPS which EFSA keeps updated through...

The basic principles for the assessment of occupational exposure due to intakes of radionuclides (The most important indirect methods used in the Protection and Safety Dept. for internal occupational exposure monitoring)

International Nuclear Information System (INIS)

Kharita, M. H.; Sakhita, K.

2009-05-01

This study shows the basic principles for the assessment of occupational exposure due to intakes of radionuclides in order to calculate the committed effective dose of each radionuclide separately. We also discussed when the routine monitoring of workers becomes useful and when the workplace monitoring is better than workers monitoring. In addition, this study contains the details of four indirect methods as they are validated in the protection and safety department, and their names are: Determination the concentration of total uranium by using fluorimetry technique, Determination the activity of two uranium isotopes 238 and 234, The activity of Polonium 210, and the activity of Radium 226 by using alpha spectrometry for urine samples collected from workers occupationally exposed to this isotope. (author)

Quantitative safety assessment of air traffic control systems through system control capacity

Science.gov (United States)

Guo, Jingjing

Quantitative Safety Assessments (QSA) are essential to safety benefit verification and regulations of developmental changes in safety critical systems like the Air Traffic Control (ATC) systems. Effectiveness of the assessments is particularly desirable today in the safe implementations of revolutionary ATC overhauls like NextGen and SESAR. QSA of ATC systems are however challenged by system complexity and lack of accident data. Extending from the idea "safety is a control problem" in the literature, this research proposes to assess system safety from the control perspective, through quantifying a system's "control capacity". A system's safety performance correlates to this "control capacity" in the control of "safety critical processes". To examine this idea in QSA of the ATC systems, a Control-capacity Based Safety Assessment Framework (CBSAF) is developed which includes two control capacity metrics and a procedural method. The two metrics are Probabilistic System Control-capacity (PSC) and Temporal System Control-capacity (TSC); each addresses an aspect of a system's control capacity. And the procedural method consists three general stages: I) identification of safety critical processes, II) development of system control models and III) evaluation of system control capacity. The CBSAF was tested in two case studies. The first one assesses an en-route collision avoidance scenario and compares three hypothetical configurations. The CBSAF was able to capture the uncoordinated behavior between two means of control, as was observed in a historic midair collision accident. The second case study compares CBSAF with an existing risk based QSA method in assessing the safety benefits of introducing a runway incursion alert system. Similar conclusions are reached between the two methods, while the CBSAF has the advantage of simplicity and provides a new control-based perspective and interpretation to the assessments. The case studies are intended to investigate the

Safety assessment of discharge chute isolation barrier preparation and installation

International Nuclear Information System (INIS)

Meichle, R.H.

1994-01-01

This analysis examines activities associated with the installation of isolation barriers in the K Basins at the Hanford Reservation. This revision adds evaluation of barrier drops on stored fuel and basin floor, identifies fuel which will be moved and addresses criticality issues with sludge. The safety assessment is made for the activities for the preparation and installation of the discharge chute isolation barriers. The safety assessment includes a hazard assessment and comparisons of potential accidents/events to those addressed by the current safety basis documentation. No significant hazards were identified. An evaluation against the USQ evaluation questions was made and the determination made that the activities do not represent a USQ. Hazard categorization techniques were used to provide a basis for readiness review classifications

HANFORD SAFETY ANALYSIS & RISK ASSESSMENT HANDBOOK (SARAH)

Energy Technology Data Exchange (ETDEWEB)

EVANS, C B

2004-12-21

The purpose of the Hanford Safety Analysis and Risk Assessment Handbook (SARAH) is to support the development of safety basis documentation for Hazard Category 2 and 3 (HC-2 and 3) U.S. Department of Energy (DOE) nuclear facilities to meet the requirements of 10 CFR 830, ''Nuclear Safety Management''. Subpart B, ''Safety Basis Requirements.'' Consistent with DOE-STD-3009-94, Change Notice 2, ''Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'' (STD-3009), and DOE-STD-3011-2002, ''Guidance for Preparation of Basis for Interim Operation (BIO) Documents'' (STD-3011), the Hanford SARAH describes methodology for performing a safety analysis leading to development of a Documented Safety Analysis (DSA) and derivation of Technical Safety Requirements (TSR), and provides the information necessary to ensure a consistently rigorous approach that meets DOE expectations. The DSA and TSR documents, together with the DOE-issued Safety Evaluation Report (SER), are the basic components of facility safety basis documentation. For HC-2 or 3 nuclear facilities in long-term surveillance and maintenance (S&M), for decommissioning activities, where source term has been eliminated to the point that only low-level, residual fixed contamination is present, or for environmental remediation activities outside of a facility structure, DOE-STD-1120-98, ''Integration of Environment, Safety, and Health into Facility Disposition Activities'' (STD-1120), may serve as the basis for the DSA. HC-2 and 3 environmental remediation sites also are subject to the hazard analysis methodologies of this standard.

Introduction to Body Composition Assessment Using the Deuterium Dilution Technique with Analysis of Urine Samples by Isotope Ratio Mass Spectrometry

International Nuclear Information System (INIS)

2010-01-01

The IAEA has fostered the more widespread use of a stable isotope technique to assess body composition in different population groups to address priority areas in public health nutrition in Member States. It has done this by supporting national and regional nutrition projects through its technical cooperation programme and coordinated research projects over many years. This publication was developed by an international group of experts to provide practical hands-on guidance in the use of this technique in settings where analysis of stable isotope ratios in biological samples is to be made by isotope ratio mass spectrometry. The publication is targeted at new users of this technique, for example nutritionists, analytical chemists and other professionals. More detailed information on the theoretical background and the practical applications of state of the art methodologies to monitor changes in body composition can be found in IAEA Human Health Series No. 3, Assessment of Body Composition and Total Energy Expenditure in Humans by Stable Isotope Techniques

Second international conference on isotopes. Conference proceedings

International Nuclear Information System (INIS)

Hardy, C.J.

1997-10-01

The Second International Conference on Isotopes (2ICI) was hosted by the Australian Nuclear Association in Sydney, NSW, Australia. The Theme of the Second Conference: Isotopes for Industry, Health and a Better Environment recognizes that isotopes have been used in these fields successfully for many years and offer prospects for increasing use in the future. The worldwide interest in the use of research reactors and accelerators and in applications of stable and radioactive isotopes, isotopic techniques and radiation in industry, agriculture, medicine, environmental studies and research in general, was considered. Other radiation issues including radiation protection and safety were also addressed. International and national overviews and subject reviews invited from leading experts were included to introduce the program of technical sessions. The invited papers were supported by contributions accepted from participants for oral and poster presentation. A Technical Exhibition was held in association with the Conference. This volume contains the foreword, technical program, the author index and of the papers (1-60) presented at the conference

Second international conference on isotopes. Conference proceedings

Energy Technology Data Exchange (ETDEWEB)

Hardy, C J [ed.

1997-10-01

The Second International Conference on Isotopes (2ICI) was hosted by the Australian Nuclear Association in Sydney, NSW, Australia. The Theme of the Second Conference: Isotopes for Industry, Health and a Better Environment recognizes that isotopes have been used in these fields successfully for many years and offer prospects for increasing use in the future. The worldwide interest in the use of research reactors and accelerators and in applications of stable and radioactive isotopes, isotopic techniques and radiation in industry, agriculture, medicine, environmental studies and research in general, was considered. Other radiation issues including radiation protection and safety were also addressed. International and national overviews and subject reviews invited from leading experts were included to introduce the program of technical sessions. The invited papers were supported by contributions accepted from participants for oral and poster presentation. A Technical Exhibition was held in association with the Conference. This volume contains the full text or extended abstracts of papers number 61- to number 114

Second international conference on isotopes. Conference proceedings

Energy Technology Data Exchange (ETDEWEB)

Hardy, C J [ed.

1997-10-01

The Second International Conference on Isotopes (2ICI) was hosted by the Australian Nuclear Association in Sydney, NSW, Australia. The Theme of the Second Conference: Isotopes for Industry, Health and a Better Environment recognizes that isotopes have been used in these fields successfully for many years and offer prospects for increasing use in the future. The worldwide interest in the use of research reactors and accelerators and in applications of stable and radioactive isotopes, isotopic techniques and radiation in industry, agriculture, medicine, environmental studies and research in general, was considered. Other radiation issues including radiation protection and safety were also addressed. International and national overviews and subject reviews invited from leading experts were included to introduce the program of technical sessions. The invited papers were supported by contributions accepted from participants for oral and poster presentation. A Technical Exhibition was held in association with the Conference. This volume contains the foreword, technical program, the author index and of the papers (1-60) presented at the conference.

Evaluation of safety assessment methodologies in Rocky Flats Risk Assessment Guide (1985) and Building 707 Final Safety Analysis Report (1987)

International Nuclear Information System (INIS)

Walsh, B.; Fisher, C.; Zigler, G.; Clark, R.A.

1990-01-01

FSARs. Rockwell International, as operating contractor at the Rocky Flats plant, conducted a safety analysis program during the 1980s. That effort resulted in Final Safety Analysis Reports (FSARs) for several buildings, one of them being the Building 707 Final Safety Analysis Report, June 87 (707FSAR) and a Plant Safety Analysis Report. Rocky Flats Risk Assessment Guide, March 1985 (RFRAG85) documents the methodologies that were used for those FSARs. Resources available for preparation of those Rocky Flats FSARs were very limited. After addressing the more pressing safety issues, some of which are described below, the present contractor (EG ampersand G) intends to conduct a program of upgrading the FSARs. This report presents the results of a review of the methodologies described in RFRAG85 and 707FSAR and contains suggestions that might be incorporated into the methodology for the FSAR upgrade effort

Validity of instruments to assess students' travel and pedestrian safety

Directory of Open Access Journals (Sweden)

Baranowski Tom

2010-05-01

Full Text Available Abstract Background Safe Routes to School (SRTS programs are designed to make walking and bicycling to school safe and accessible for children. Despite their growing popularity, few validated measures exist for assessing important outcomes such as type of student transport or pedestrian safety behaviors. This research validated the SRTS school travel survey and a pedestrian safety behavior checklist. Methods Fourth grade students completed a brief written survey on how they got to school that day with set responses. Test-retest reliability was obtained 3-4 hours apart. Convergent validity of the SRTS travel survey was assessed by comparison to parents' report. For the measure of pedestrian safety behavior, 10 research assistants observed 29 students at a school intersection for completion of 8 selected pedestrian safety behaviors. Reliability was determined in two ways: correlations between the research assistants' ratings to that of the Principal Investigator (PI and intraclass correlations (ICC across research assistant ratings. Results The SRTS travel survey had high test-retest reliability (κ = 0.97, n = 96, p Conclusions These validated instruments can be used to assess SRTS programs. The pedestrian safety behavior checklist may benefit from further formative work.

Assessment of safety of the nuclear installations of the world

International Nuclear Information System (INIS)

Thomas, B.A.; Pozniakov, N.; Banga, U.

1992-01-01

Incidents and accidents periodically remind us that preventive measures at nuclear installations are not fully reliable. Although sound design is widely recognized to be prerequisite for safe operation, it is not sufficient. An active management that compensates for the weak aspects of the installations design by redundant operational provisions, is the key factor to ensure safe operation. Safety of nuclear installations cannot be assessed on an emotional basis. Since 1986, accurate safety assessment techniques based on an integrated approach to operational safety have been made available by the ASSET services and are applicable to any industrial process dealing with nuclear materials. The ASSET methodology enables to eliminate in advance the Root Causes of the future accidents by introducing practical safety culture principles in the current managerial practices

Safety assessment driving radioactive waste management solutions (SADRWMS Methodology) implemented in a software tool (SAFRAN)

Energy Technology Data Exchange (ETDEWEB)

Kinker, M., E-mail: M.Kinker@iaea.org [International Atomic Energy Agency (IAEA), Vienna (Austria); Avila, R.; Hofman, D., E-mail: rodolfo@facilia.se [FACILIA AB, Stockholm (Sweden); Jova Sed, L., E-mail: jovaluis@gmail.com [Centro Nacional de Seguridad Nuclear (CNSN), La Habana (Cuba); Ledroit, F., E-mail: frederic.ledroit@irsn.fr [IRSN PSN-EXP/SSRD/BTE, (France)

2013-07-01

In 2004, the International Atomic Energy Agency (IAEA) organized the International Project on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) to examine international approaches to safety assessment for predisposal management of radioactive waste. The initial outcome of the SADRWMS Project was achieved through the development of flowcharts which could be used to improve the mechanisms for applying safety assessment methodologies to predisposal management of radioactive waste. These flowcharts have since been incorporated into DS284 (General Safety Guide on the Safety Case and Safety Assessment for Predisposal Management of Radioactive Waste), and were also considered during the early development stages of the Safety Assessment Framework (SAFRAN) Tool. In 2009 the IAEA presented DS284 to the IAEA Waste Safety Standards Committee, during which it was proposed that the graded approach to safety case and safety assessment be illustrated through the development of Safety Reports for representative predisposal radioactive waste management facilities and activities. To oversee the development of these reports, it was agreed to establish the International Project on Complementary Safety Reports: Development and Application to Waste Management Facilities (CRAFT). The goal of the CRAFT project is to develop complementary reports by 2014, which the IAEA could then publish as IAEA Safety Reports. The present work describes how the DS284 methodology and SAFRAN Tool can be applied in the development and review of the safety case and safety assessment to a range of predisposal waste management facilities or activities within the Region. (author)

Safety assessment driving radioactive waste management solutions (SADRWMS Methodology) implemented in a software tool (SAFRAN)

International Nuclear Information System (INIS)

Kinker, M.; Avila, R.; Hofman, D.; Jova Sed, L.; Ledroit, F.

2013-01-01

In 2004, the International Atomic Energy Agency (IAEA) organized the International Project on Safety Assessment Driving Radioactive Waste Management Solutions (SADRWMS) to examine international approaches to safety assessment for predisposal management of radioactive waste. The initial outcome of the SADRWMS Project was achieved through the development of flowcharts which could be used to improve the mechanisms for applying safety assessment methodologies to predisposal management of radioactive waste. These flowcharts have since been incorporated into DS284 (General Safety Guide on the Safety Case and Safety Assessment for Predisposal Management of Radioactive Waste), and were also considered during the early development stages of the Safety Assessment Framework (SAFRAN) Tool. In 2009 the IAEA presented DS284 to the IAEA Waste Safety Standards Committee, during which it was proposed that the graded approach to safety case and safety assessment be illustrated through the development of Safety Reports for representative predisposal radioactive waste management facilities and activities. To oversee the development of these reports, it was agreed to establish the International Project on Complementary Safety Reports: Development and Application to Waste Management Facilities (CRAFT). The goal of the CRAFT project is to develop complementary reports by 2014, which the IAEA could then publish as IAEA Safety Reports. The present work describes how the DS284 methodology and SAFRAN Tool can be applied in the development and review of the safety case and safety assessment to a range of predisposal waste management facilities or activities within the Region. (author)

Safety assessment of genetically modified crops

International Nuclear Information System (INIS)

Atherton, Keith T.

2002-01-01

The development of genetically modified (GM) crops has prompted widespread debate regarding both human safety and environmental issues. Food crops produced by modern biotechnology using recombinant techniques usually differ from their conventional counterparts only in respect of one or a few desirable genes, as opposed to the use of traditional breeding methods which mix thousands of genes and require considerable efforts to select acceptable and robust hybrid offspring. The difficulties of applying traditional toxicological testing and risk assessment procedures to whole foods are discussed along with the evaluation strategies that are used for these new food products to ensure the safety of these products for the consumer

Assessing progress in the development of safety culture

International Nuclear Information System (INIS)

Rotaru, I.; Ghita, S.; Biro, L.

2002-01-01

This paper is focussed on the organizational culture and learning processes required for the implementation of all aspects of safety culture. There is no prescriptive formula for improving safety culture. However, some common characteristics and practices are emerging that can be adopted by organizations in order to make progress. The paper refers to some approaches that have been successful in a number of countries. The experience of the international nuclear industry in the development and improvement of safety culture could be extended and found useful in other nuclear activities, irrespective of scale. The examples given of specific practice cover a wide range of activities including analysis of events, the regulatory approach on safety culture, employee participation and safety performance measures. Many of these practices may be relevant to smaller organizations and could contribute to improving safety culture, whatever the size of the organization. The most effective approach is to pursue a range of practices that can be mutually supportive in the development of a progressive safety culture, supported by professional standards, organizational and management commitment. Some guidance is also given on the assessment of safety culture and on the detection of a weakening safety culture. Few suggestions for accelerating the safety culture development and improvement process are also provided. (author)

Crane Safety Assessment Method Based on Entropy and Cumulative Prospect Theory

Directory of Open Access Journals (Sweden)

Aihua Li

2017-01-01

Full Text Available Assessing the safety status of cranes is an important problem. To overcome the inaccuracies and misjudgments in such assessments, this work describes a safety assessment method for cranes that combines entropy and cumulative prospect theory. Firstly, the proposed method transforms the set of evaluation indices into an evaluation vector. Secondly, a decision matrix is then constructed from the evaluation vectors and evaluation standards, and an entropy-based technique is applied to calculate the index weights. Thirdly, positive and negative prospect value matrices are established from reference points based on the positive and negative ideal solutions. Thus, this enables the crane safety grade to be determined according to the ranked comprehensive prospect values. Finally, the safety status of four general overhead traveling crane samples is evaluated to verify the rationality and feasibility of the proposed method. The results demonstrate that the method described in this paper can precisely and reasonably reflect the safety status of a crane.

An approach for risk informed safety culture assessment for Canadian nuclear power stations

International Nuclear Information System (INIS)

Nelson, W.R.

2010-01-01

One of the most important components of effective safety and risk management for nuclear power stations is a healthy safety culture. DNV has developed an approach for risk informed safety culture assessment that combines two complementary paradigms for safety and risk management: loss prevention - for preventing and intervening in accidents; and critical function management - for achieving safety and performance goals. Combining these two paradigms makes it possible to provide more robust systems for safety management and to support a healthy safety culture. This approach is being applied to safety culture assessment in partnership with a Canadian nuclear utility. (author)

Safety assessment of existing highway bridges and viaducts

NARCIS (Netherlands)

Maljaars, J.; Steenbergen, R.; Abspoel, L.; Kolstein, M.H.

2012-01-01

The assessment of the structural safety of existing br idges and viaducts becomes increasingly important in many countries owing to an increase in traffic loads. Most existing standards, however, are developed for the design of new structures. For this reason, an assessment method for determining

Development of a New Safety Culture Assessment Method for Nuclear Power Plants (NPPs) (A study to suggest a new safety culture assessment method in nuclear power plants)

International Nuclear Information System (INIS)

Han, Sang Min; Seong, Poong Hyun

2014-01-01

This study is conducted to suggest a new safety culture assessment method in nuclear power plants. Criteria with various existing safety culture analysis methods are united, and reliability analysis methods are applied. The concept of the most representative methods, Fault Tree Analysis (FTA) and Failure Mode and Effect Analysis (FMEA), are adopted to assess safety culture. Through this application, it is expected that the suggested method will bring results with convenience and objectiveness

Development of a New Safety Culture Assessment Method for Nuclear Power Plants (NPPs) (A study to suggest a new safety culture assessment method in nuclear power plants)

Energy Technology Data Exchange (ETDEWEB)

Han, Sang Min; Seong, Poong Hyun [KAIST, Daejeon (Korea, Republic of)

2014-08-15

This study is conducted to suggest a new safety culture assessment method in nuclear power plants. Criteria with various existing safety culture analysis methods are united, and reliability analysis methods are applied. The concept of the most representative methods, Fault Tree Analysis (FTA) and Failure Mode and Effect Analysis (FMEA), are adopted to assess safety culture. Through this application, it is expected that the suggested method will bring results with convenience and objectiveness.

Overview of the ISAM safety assessment methodology

International Nuclear Information System (INIS)

Simeonov, G.

2003-01-01

The ISAM safety assessment methodology consists of the following key components: specification of the assessment context description of the disposal system development and justification of scenarios formulation and implementation of models running of computer codes and analysis and presentation of results. Common issues run through two or more of these assessment components, including: use of methodological and computer tools, collation and use of data, need to address various sources of uncertainty, building of confidence in the individual components, as well as the overall assessment. The importance of the iterative nature of the assessment should be recognised

Building quality into performance and safety assessment software

International Nuclear Information System (INIS)

Wojciechowski, L.C.

2011-01-01

Quality assurance is integrated throughout the development lifecycle for performance and safety assessment software. The software used in the performance and safety assessment of a Canadian deep geological repository (DGR) follows the CSA quality assurance standard CSA-N286.7 [1], Quality Assurance of Analytical, Scientific and Design Computer Programs for Nuclear Power Plants. Quality assurance activities in this standard include tasks such as verification and inspection; however, much more is involved in producing a quality software computer program. The types of errors found with different verification methods are described. The integrated quality process ensures that defects are found and corrected as early as possible. (author)

Safety assessment input for site selection - the Swedish example - 59031

International Nuclear Information System (INIS)

Andersson, Johan

2012-01-01

Svensk Kaernbraenslehantering AB (SKB) has performed comprehensive investigations of two candidate sites for a final repository for Sweden's spent nuclear fuel. In March 2011 SKB decided to submit licence applications for a final repository at Forsmark. Before selection, SKB stated that the site that offers the best prospects for achieving long-term safety in practice would be selected. Based on experiences previous safety assessments, a number of issues related to long-term safety need to be considered in the context of site comparison. The factors include sensitivity to climate change such as periods of permafrost and glaciations, rock mechanics evolution including the potential for thermally induced spalling and sensitivity to potential future earthquakes, current and future groundwater flow, evolution of groundwater composition and proximity to mineral resources. Each of these factors related to long-term safety for the two candidate sites is assessed in a comparative analysis of site characteristics. The assessment also considers differences in biosphere conditions and in the confidence of the site descriptions. The comparison is concluded by an assessment on how the identified differences would affect the estimated radiological risk from a repository located at either of the sites. The assessment concludes that there are a number of safety related site characteristics for which the analyses do not show any decisive differences in terms of implications on safety, between the sites Forsmark and Laxemar. However, the frequency of water conducting fractures at repository depth is much smaller at Forsmark than at Laxemar. This difference, in turn, affects the future stability of the current favourable groundwater composition, which combined with the much higher flows at Laxemar would, for the current repository design, lead to a breach in the safety functions for the buffer and the canister for many more deposition positions at Laxemar than at Forsmark. Thereby

Project SAFE. Update of the SFR-1 safety assessment. Phase 1

International Nuclear Information System (INIS)

Andersson, Johan; Riggare, P.; Skagius, K.

1998-10-01

SFR-1 is a facility for disposal of low-level radioactive operational waste from the nuclear power plants in Sweden. Low-level radioactive waste from industry, medicine, and research is also disposed in SFR-1. The facility is situated in bedrock beneath the Baltic Sea, 1 km off the coast near the Forsmark nuclear power plant. SFR-1 was built between the years 1983 and 1988. An assessment of the long-term performance of the facility was included in the vast documentation that was a part of the application for an operational license. The assessment was presented in the form of a final safety report. In the operational licence for SFR-1 it is stated that renewed safety assessments should be carried out at least each ten years. In order to meet this demand SKB has launched a special project, SAFE (Safety Assessment of Final Disposal of Operational Radioactive Waste). The aim of the project is to update the safety analysis and to prepare a safety report that will be presented to the Swedish authorities not later than year 2000. Project SAFE is divided into three phases. The first phase is a prestudy, and the results of the prestudy are given in this report. The aim of the prestudy is to identify issues where additional studies would improve the basis for the updated safety analysis as well as to suggest how these studies should be carried out. The work has been divided into six different topics, namely the inventory, the near field, the far field, the biosphere, radionuclide transport calculations and scenarios. For each topic the former safety reports and regulatory reviews are scrutinised and needs for additional work is identified. The evaluations are given in appendices covering the respective topics. The main report is a summary of the appendices with a more stringent description of the repository system and the processes that are of interest and therefore should be addressed in an updated safety assessment. However, it should be pointed out that one of the

Human reliability analysis methods for probabilistic safety assessment

International Nuclear Information System (INIS)

Pyy, P.

2000-11-01

Human reliability analysis (HRA) of a probabilistic safety assessment (PSA) includes identifying human actions from safety point of view, modelling the most important of them in PSA models, and assessing their probabilities. As manifested by many incidents and studies, human actions may have both positive and negative effect on safety and economy. Human reliability analysis is one of the areas of probabilistic safety assessment (PSA) that has direct applications outside the nuclear industry. The thesis focuses upon developments in human reliability analysis methods and data. The aim is to support PSA by extending the applicability of HRA. The thesis consists of six publications and a summary. The summary includes general considerations and a discussion about human actions in the nuclear power plant (NPP) environment. A condensed discussion about the results of the attached publications is then given, including new development in methods and data. At the end of the summary part, the contribution of the publications to good practice in HRA is presented. In the publications, studies based on the collection of data on maintenance-related failures, simulator runs and expert judgement are presented in order to extend the human reliability analysis database. Furthermore, methodological frameworks are presented to perform a comprehensive HRA, including shutdown conditions, to study reliability of decision making, and to study the effects of wrong human actions. In the last publication, an interdisciplinary approach to analysing human decision making is presented. The publications also include practical applications of the presented methodological frameworks. (orig.)

Initialization of Safety Assessment Process for the Croatian Radioactive Waste repository on Trgovska gora

International Nuclear Information System (INIS)

Lokner, V.; Levanat, I.; Subasic, D.

2000-01-01

An iterative process of safety assessment, presently focusing on the site-specific evaluation of the post-closure phase for the prospective LILW repository on Trgovska gora in Croatia, has recently been initiated. The primary aim of the first assessment iterations is to provide the experts involved, the regulators and the general public with a reasonable assurance that the applicable long term performance and safety objectives can be met. Another goal is to develop a sufficient understanding of the system behavior to support decisions about the site investigation, the facility design, the waste acceptance criteria and the closure conditions. In this initial phase, the safety assessment is structured in a manner following closely methodology of the ISAM. The International Programme for Improving Long Term Safety Assessment Methodologies for Near Surface Radioactive Waste Disposal Facilities the IAEA coordinated research program started in 1997. Results of the safety assessment first iteration will be organized and presented in the form of a preliminary safety analysis report (PSAR), expected to be completed in the second part of the year 2000. As the first report on the initiated safety assessment activities, the PSAR will describe the concept and aims of the assessment process. Particular emphasis will be placed on description of the key elements of a safety assessment approach by: a) defining the assessment context; b) providing description of the disposal system; c) developing and justifying assessment scenarios; d) formulating and implementing models; and e) interpreting the scoping calculations. (author)

Development of the KINS Safety Culture Maturity Model for Self and Independent Assessment

International Nuclear Information System (INIS)

Sheen, C.; Choi, Y.S.

2016-01-01

Safety culture of an organization is cultivated and affected not only by societal and regulatory environment of the organization, but by its philosophies, policies, events and activities experienced in the process of accomplishing its mission. The safety culture would be continuously changed by the interactions between its members along with time as an organic entity. In order to perform a systematic self- or independent assessment of safety culture, a safety culture assessment model (SCAM) properly reflecting cultural characteristics should be necessary. In addition, a SCAM should be helpful not only to establish correct directions, goals, and strategies for safety culture development, but should anticipating obstacles against safety culture development in the implementation process derived from the assessment. In practical terms, a SCAM should be useful for deriving effective guidelines and implementing of corrective action programs for the evaluated organization. Korea Institute of Nuclear Safety (KINS) performed a research project for six years to develop a SCAM satisfying the above prerequisites for self- and independent assessment. The KINS SCAM was developed based on the five stage safety culture maturity model proposed by Professor Patrick Hudson and was modified into four stages to reflect existing safety culture assessment experiences at Korean nuclear power plants. In order to define the change mechanism of safety culture for development and reversion, the change model proposed by Prochaska and DiClemente was introduced into KINS SCAM and developed into the Spiral Change Model.

Climate and climate-related issues for the safety assessment SR-Can

International Nuclear Information System (INIS)

Naeslund, Jens-Ove

2006-11-01

The purpose of this report is to document current scientific knowledge of the climate-related conditions and processes relevant to the long-term safety of a KBS-3 repository to a level required for an adequate treatment in the safety assessment SR-Can. The report also includes a concise background description of the climate system. The report includes three main chapters: A description of the climate system (Chapter 2); Identification and discussion of climate-related issues (Chapter 3); and, A description of the evolution of climate-related conditions for the safety assessment (Chapter 4). Chapter 2 includes an overview of present knowledge of the Earth climate system and the climate conditions that can be expected to occur in Sweden on a 100,000 year time perspective. Based on this, climate-related issues relevant for the long-term safety of a KBS-3 repository are identified. These are documented in Chapter 3 'Climate-related issues' to a level required for an adequate treatment in the safety assessment. Finally, in Chapter 4, 'Evolution of climate-related conditions for the safety assessment' an evolution for a 120,000 year period is presented, including discussions of identified climate-related issues of importance for repository safety. The documentation is from a scientific point of view not exhaustive, since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of a safety assessment. As further described in the SR-Can Main Report and in the Features Events and Processes report, the content of the present report has been audited by comparison with FEP databases compiled in other assessment projects. This report follows as far as possible the template for documentation of processes regarded as internal to the repository system. However, the term processes is not used in this report, instead the term issue has been used. Each issue includes a set of processes together resulting in the behaviour of a

Climate and climate-related issues for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Naeslund, Jens-Ove (comp.)

2006-11-15

The purpose of this report is to document current scientific knowledge of the climate-related conditions and processes relevant to the long-term safety of a KBS-3 repository to a level required for an adequate treatment in the safety assessment SR-Can. The report also includes a concise background description of the climate system. The report includes three main chapters: A description of the climate system (Chapter 2); Identification and discussion of climate-related issues (Chapter 3); and, A description of the evolution of climate-related conditions for the safety assessment (Chapter 4). Chapter 2 includes an overview of present knowledge of the Earth climate system and the climate conditions that can be expected to occur in Sweden on a 100,000 year time perspective. Based on this, climate-related issues relevant for the long-term safety of a KBS-3 repository are identified. These are documented in Chapter 3 'Climate-related issues' to a level required for an adequate treatment in the safety assessment. Finally, in Chapter 4, 'Evolution of climate-related conditions for the safety assessment' an evolution for a 120,000 year period is presented, including discussions of identified climate-related issues of importance for repository safety. The documentation is from a scientific point of view not exhaustive, since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of a safety assessment. As further described in the SR-Can Main Report and in the Features Events and Processes report, the content of the present report has been audited by comparison with FEP databases compiled in other assessment projects. This report follows as far as possible the template for documentation of processes regarded as internal to the repository system. However, the term processes is not used in this report, instead the term issue has been used. Each issue includes a set of processes together resulting in the

Availability and use of medical isotopes in Canada : performed as part of a radiological terrorism risk assessment. Technical memorandum

International Nuclear Information System (INIS)

Larsson, C.L.

2004-12-01

An assessment of the availability of radioactive material used for medical applications in Canada has been performed as part of the CBRN Research and Technology Initiative (CRTI) Project CRTI-02-0024RD (Probabilistic Risk Assessment Tool for Radiological Dispersal Devices). A general list of medical radioisotopes used worldwide was compiled via literature searches and Internet investigations. This list was then compared to all isotopes licenced to healthcare facilities in Canada. Sources of lesser concern for this study, such as noble gases, short-lived isotopes, and radioisotopes not licenced for medical applications in Canada, were eliminated. The remaining sources were then analysed for frequency of use and maximum licenced activity to assess which materials would be of highest concern in relation to radiological terrorism. A detailed description of the application, typical administered activity, and other relevant information for these most common and highest licenced activity medical sources was assembled to feed directly into the risk assessment database. A general discussion of security in healthcare facilities is also given. Due to the constant advances made in medicine, the information relating to licenced isotopes is dynamic and thus requires updating to ensure the database is kept current. (author)

Integrated safety assessment report, Haddam Neck Plant (Docket No. 50-213): Integrated Safety Assessment Program: Draft report

International Nuclear Information System (INIS)

1987-07-01

The integrated assessment is conducted on a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. Procedures allow for a periodic updating of the schedules to account for licensing issues that arise in the future. The Haddam Neck Plant is one of two plants being reviewed under the pilot program. This report indicates how 82 topics selected for review were addressed, and presents the staff's recommendations regarding the corrective actions to resolve the 82 topics and other actions to enhance plant safety. 135 refs., 4 figs., 5 tabs

Safety Assessment Methodologies and Their Application in Development of Near Surface Waste Disposal Facilities--ASAM Project

International Nuclear Information System (INIS)

Batandjieva, B.; Metcalf, P.

2003-01-01

Safety of near surface disposal facilities is a primary focus and objective of stakeholders involved in radioactive waste management of low and intermediate level waste and safety assessment is an important tool contributing to the evaluation and demonstration of the overall safety of these facilities. It plays significant role in different stages of development of these facilities (site characterization, design, operation, closure) and especially for those facilities for which safety assessment has not been performed or safety has not been demonstrated yet and the future has not been decided. Safety assessments also create the basis for the safety arguments presented to nuclear regulators, public and other interested parties in respect of the safety of existing facilities, the measures to upgrade existing facilities and development of new facilities. The International Atomic Energy Agency (IAEA) has initiated a number of research coordinated projects in the field of development and improvement of approaches to safety assessment and methodologies for safety assessment of near surface disposal facilities, such as NSARS (Near Surface Radioactive Waste Disposal Safety Assessment Reliability Study) and ISAM (Improvement of Safety Assessment Methodologies for Near Surface Disposal Facilities) projects. These projects were very successful and showed that there is a need to promote the consistent application of the safety assessment methodologies and to explore approaches to regulatory review of safety assessments and safety cases in order to make safety related decisions. These objectives have been the basis of the IAEA follow up coordinated research project--ASAM (Application of Safety Assessment Methodologies for Near Surface Disposal Facilities), which will commence in November 2002 and continue for a period of three years

Operational safety assessment of underground test facilities for mined geologic waste disposal

International Nuclear Information System (INIS)

Elder, H.K.

1993-01-01

This paper describes the operational safety assessment for the underground facilities for the exploratory studies facility (ESF) at the Yucca Mountain Project. The systematic identification and evaluation of hazards related to the ESF is an integral part of the systems engineering process; whereby safety is considered during planning, design, testing, and construction. A largely qualitative approach based on the analysis of potential accidents was used since radiological safety analysis was not required. The risk assessment summarized credible accident scenarios and the design provides mitigation of the risks to a level that the facility can be constructed and operated with an adequate level of safety. The risk assessment also provides reasonable assurance that all identifiable major accident scenarios have been reviewed and design mitigation features provided to ensure an adequate level of safety

Radionuclide transport report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This document compiles radionuclide transport calculations of a KBS-3 repository for the safety assessment SR-Site. The SR-Site assessment supports the licence application for a final repository at Forsmark, Sweden

The probability safety assessment impact on the BR2 refurbishment

International Nuclear Information System (INIS)

Pouleur, Yvan

1995-01-01

The probabilistic safety assessment (PSA) study has proven its worth by establishing a sensitive safety screening of the reactor. It has focused engineering forces to technically improve safety systems and to measure the influence of functional modifications. In the future, the project will be developed in a living way, to reinforce the present structure along with continuous safety monitoring of the reactor and to develop engineers and operators safety skills. This paper presents the PSA impact on the BR2 (Belgian Reactor Two) refurbishment. (author)

Biomolecular tracing using long-lived isotopes

International Nuclear Information System (INIS)

Vogel, J.S.; Turteltaub, K.W.; Frantz, C.E.; Keating, G.; Felton, J.S.; Southon, J.R.; Roberts, M.R.; Gledhill, B.L.

1992-01-01

Accelerator mass spectrometry (AMS) was developed over the past 15 years as an essential tool for detecting long-lived, cosmogenic radio-isotopes in the earth and space sciences. We apply this technology to the measurement of chemical kinetics, primarily in biomedical systems, which had heretofore employed short-lived isotopes and/or long counting times to quantify radio-isotopic labels. AMS provides detection efficiencies of ∼ 1%, 10 3 to 10 6 better than decay-counting. Long-lived isotopes are used and detected with AMS at concentrations which reduce sample size, chemical dose, radiation safety hazards and radiolysis. We measure 3 H, 7,1O Be, 14 C, 26 Al, 36 CI, 41 Ca and 129 I, but most of our current program uses 14 C. Initial experiments involved research on the genotoxicity of mutagens in cooked foods and reversible binding of compounds to antibodies. Through collaborations, we apply AMS detection to research in carcinogenesis, pharmacokinetics of toxins, elemental metabolism, distribution of topical medications and nutrition

IAEA Issues Report on Mission to Review Japan's Nuclear Power Plant Safety Assessment Process

International Nuclear Information System (INIS)

2012-01-01

Full text: A team of international nuclear safety experts has delivered its report on a mission it conducted from 21-31 January 2012 to review Japan's process for assessing nuclear safety at the nation's nuclear power plants. International Atomic Energy Agency (IAEA) officials delivered the IAEA Mission Report to Japanese officials yesterday and made it publicly available today. Following the 11 March 2011 accident at TEPCO's Fukushima Daiichi Nuclear Power Station, Japan's Nuclear and Industrial Safety Agency (NISA) announced the development of a revised safety assessment process for the nation's nuclear power reactors. At the request of the Government of Japan, the IAEA organized a team of five IAEA and three international nuclear safety experts and visited Japan to review NISA's approach to the Comprehensive Assessments for the Safety of Existing Power Reactor Facilities and how NISA examines the results submitted by nuclear operators. A Preliminary Summary Report was issued on 31 January. 'The mission report provides additional information regarding the team's recommendations and overall finding that NISA's instructions to power plants and its review process for the Comprehensive Safety Assessments are generally consistent with IAEA Safety Standards', said team leader James Lyons, Director of the IAEA's Nuclear Installation Safety Division. National safety assessments and their peer review by the IAEA are a key component of the IAEA Action Plan on Nuclear Safety, which was approved by the Agency's Member States following last year's nuclear accident at Fukushima Daiichi Nuclear Power Station. The IAEA safety review mission held meetings in Tokyo with officials from NISA, the Japanese Nuclear Energy Safety Organization (JNES), and the Kansai Electric Power Company (KEPCO), and the team visited the Ohi Nuclear Power Station to see an example of how Japan's Comprehensive Safety Assessment is being implemented by nuclear operators. In its report delivered today

Safety assessment of geologic repositories for nuclear waste

International Nuclear Information System (INIS)

Bartlett, J.W.; Burkholder, H.C.; Winegardner, W.K.

1977-01-01

Consideration of geologic isolation for final disposition of radioactive wastes has led to the need for evaluation of the safety of the concept. Such evaluations require consideration of factors not encountered in conventional risk analysis: consequences at times and places far removed from the repository site; indirect, complex, and alternative pathways between the waste and the point of potential consequences; a highly limited data base; and limited opportunity for experimental verification of results. R and D programs to provide technical safety evaluations are under way. Three methods are being considered for the probabilistic aspects of the evaluations: fault tree analysis, repository simulation analysis, and system stability analysis. Nuclide transport models, currently in a relatively advanced state of development, are used to evaluate consequences of postulated loss of geologic isolation. This paper outlines the safety assessment methods, unique features of the assessment problem that affect selection of methods and reliability of results, and available results. It also discusses potential directions for future work

Safety Assessment in the AREVA Group: Operating Experience from a Self-Assessment Tool

International Nuclear Information System (INIS)

Coye de Brunélis, T.; Mignot, E.; Sidaner, J.-F.

2016-01-01

The expression “safety culture” first appeared following analysis of the Chernobyl accident in 1986. It was first defined in INSAG-4 (International Nuclear Safety Advisory Group safety series) in 1991. Other events have occurred in nuclear facilities and during transportation since Chernobyl: Tokai Mura in 1999, Roissy Transport in 2002, Davis Besse in 2002, Thorp in 2005. These events show that the initial approach was too simplistic. Based on this observation, the definition of safety culture was supplemented by including concepts of cultural value (associated with the country and the company) and human and organizational factors, and was integrated in that form with the emergence and implementation of integrated management systems (IMS). Today, the concept of nuclear safety culture covers a wide set of factors such as safety, quality, corporate culture, defined processes and policies, organizations and related resources. Any assessment of people’s safety culture, particularly people directly involved in facility operations, is thus part of a comprehensive policy and contributes to a de facto demonstration of the priority which management assigns to safety.

Assessment of international reference materials for isotope-ratio analysis (IUPAC Technical Report)

Science.gov (United States)

Brand, Willi A.; Coplen, Tyler B.; Vogl, Jochen; Rosner, Martin; Prohaska, Thomas

2014-01-01

Since the early 1950s, the number of international measurement standards for anchoring stable isotope delta scales has mushroomed from 3 to more than 30, expanding to more than 25 chemical elements. With the development of new instrumentation, along with new and improved measurement procedures for studying naturally occurring isotopic abundance variations in natural and technical samples, the number of internationally distributed, secondary isotopic reference materials with a specified delta value has blossomed in the last six decades to more than 150 materials. More than half of these isotopic reference materials were produced for isotope-delta measurements of seven elements: H, Li, B, C, N, O, and S. The number of isotopic reference materials for other, heavier elements has grown considerably over the last decade. Nevertheless, even primary international measurement standards for isotope-delta measurements are still needed for some elements, including Mg, Fe, Te, Sb, Mo, and Ge. It is recommended that authors publish the delta values of internationally distributed, secondary isotopic reference materials that were used for anchoring their measurement results to the respective primary stable isotope scale.

Environment, Safety, and Health Self-Assessment Report, Fiscal Year 2008

Energy Technology Data Exchange (ETDEWEB)

Chernowski, John

2009-02-27

Lawrence Berkeley National Laboratory's Environment, Safety, and Health (ES&H) Self-Assessment Program ensures that Integrated Safety Management (ISM) is implemented institutionally and by all divisions. The Self-Assessment Program, managed by the Office of Contract Assurance (OCA), provides for an internal evaluation of all ES&H programs and systems at LBNL. The functions of the program are to ensure that work is conducted safely, and with minimal negative impact to workers, the public, and the environment. The Self-Assessment Program is also the mechanism used to institute continuous improvements to the Laboratory's ES&H programs. The program is described in LBNL/PUB 5344, Environment, Safety, and Health Self-Assessment Program and is composed of four distinct assessments: the Division Self-Assessment, the Management of Environment, Safety, and Health (MESH) review, ES&H Technical Assurance, and the Appendix B Self-Assessment. The Division Self-Assessment uses the five core functions and seven guiding principles of ISM as the basis of evaluation. Metrics are created to measure performance in fulfilling ISM core functions and guiding principles, as well as promoting compliance with applicable regulations. The five core functions of ISM are as follows: (1) Define the Scope of Work; (2) Identify and Analyze Hazards; (3) Control the Hazards; (4) Perform the Work; and (5) Feedback and Improvement. The seven guiding principles of ISM are as follows: (1) Line Management Responsibility for ES&H; (2) Clear Roles and Responsibilities; (3) Competence Commensurate with Responsibilities; (4) Balanced Priorities; (5) Identification of ES&H Standards and Requirements; (6) Hazard Controls Tailored to the Work Performed; and (7) Operations Authorization. Performance indicators are developed by consensus with OCA, representatives from each division, and Environment, Health, and Safety (EH&S) Division program managers. Line management of each division performs the

Safety assessment of envisaged systems for automotive hydrogen supply and utilization

Energy Technology Data Exchange (ETDEWEB)

Landucci, Gabriele [Dipartimento di Ingegneria Chimica, Chimica Industriale e Scienza dei Materiali, Universita di Pisa, via Diotisalvi n.2, 56126 Pisa (Italy); Tugnoli, Alessandro; Cozzani, Valerio [Dipartimento di Ingegneria Chimica, Mineraria e delle Tecnologie Ambientali, Alma Mater Studiorum - Universita di Bologna, via Terracini n.28, 40131 Bologna (Italy)

2010-02-15

A novel consequence-based approach was applied to the inherent safety assessment of the envisaged hydrogen production, distribution and utilization systems, in the perspective of the widespread hydrogen utilization as a vehicle fuel. Alternative scenarios were assessed for the hydrogen system chain from large scale production to final utilization. Hydrogen transportation and delivery was included in the analysis. The inherent safety fingerprint of each system was quantified by a set of Key Performance Indicators (KPIs). Rules for KPIs aggregation were considered for the overall assessment of the system chains. The final utilization stage resulted by large the more important for the overall expected safety performance of the system. Thus, comparison was carried out with technologies proposed for the use of other low emission fuels, as LPG and natural gas. The hazards of compressed hydrogen-fueled vehicles resulted comparable, while reference innovative hydrogen technologies evidenced a potentially higher safety performance. Thus, switching to the inherently safer technologies currently under development may play an important role in the safety enhancement of hydrogen vehicles, resulting in a relevant improvement of the overall safety performance of the entire hydrogen system. (author)

Safety cases for the co-ordinated research project on improvement of safety assessment methodologies for near surface radioactive waste disposal facilities (ISAM)