PA6 and Kevlar fiber reinforced isotactic polypropylene: Structure, mechanical properties and crystallization and melting behavior

International Nuclear Information System (INIS)

Zhao, Songfang; Cheng, Lei; Guo, Yong; Zheng, Yuying; Li, Baoming

2012-01-01

Highlights: ► KF was modified with caprolactam using toluenediisocyanate (TDI) as bridge. ► Modified KF improves interfacial interaction of iPP/KF/PA6 composites. ► Fiber and nylon 6 inhibited the crystallization of PP continuous phase. -- Abstract: To improve the thermal and mechanical properties of isotactic polypropylene (iPP), iPP/Kevlar fiber (KF)/polyamide 6 (PA6) composites were prepared via the melt-extrusion method on twin-screw extruder. Kevlar fiber was modified with caprolactam using toluenediisocyanate (TDI) as bridge. The microstructure of modified KF was successfully characterized by Fourier transform infrared (FT-IR), X-ray photoelectron spectrometer (XPS) and scanning electron microscopy (SEM), the results showed that KF was bonded with caprolactam and became coarser. Then the modified KF was introduced into iPP, the composites have better mechanical and thermal properties, implying that modification of KF was helpful to improve the interfacial interaction of iPP/KF/PA6 composites. Besides, the crystallization curves indicated that crystallization behavior of PA6 in the composites was homogeneous and fractional. Furthermore, compatibilizer content played an important role in the mechanical and thermal properties of composites.

MeV energy electron beam induced damage in isotactic polypropylene

Energy Technology Data Exchange (ETDEWEB)

Mathakari, N.L.; Bhoraskar, V.N. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Pune 411007 (India); Dhole, S.D. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Pune 411007 (India)], E-mail: sanjay@physics.unipune.ernet.in

2008-06-15

A few thin films of isotactic polypropylene were irradiated with 6 MeV energy electrons, in the fluence range from 5 x 10{sup 14} to 2 x 10{sup 15} electrons/cm{sup 2}. The structural, optical and mechanical properties were characterized by techniques such as FTIR, UV-vis, XRD, SEM, hardness and contact angle measurements. The FTIR spectra indicate that C-H and C-C bonds are scissioned and an isotactic arrangement of chains is partially destroyed. Moreover, the new carbonyl groups (C=O) are observed, which signifies oxidation. The UV-vis spectra shows a red shift in the absorption edge from pristine value of 240 to 380 nm, which corresponds to decrease in the optical band gap from 5.17 to 3.27 eV. This is because of the formation of conjugated double bonds as well as carbonization. The crystalline properties were analysed using XRD and it shows no profound change. This result may attribute that the radiation-induced changes have probably occurred to a large extent in amorphous regions. However, surface morphology by SEM and contact angle measurements showed considerable surface roughening, which indicates an uneven evolution of gases from the surface. Interestingly, the surface hardness of the films was found to increase with fluence and it may be due to crosslinking and carbonization on the surface. Overall, in conclusion this study shows considerable modifications in the physicochemical properties of isotactic polypropylene irradiated by 6 MeV energy pulsed electrons.

The Influence of Molecular Weight and Tacticity on Thermal, Morphological and Mechanical Properties of Ziegler–Natta Catalyzed Isotactic and Syndiotactic Polypropylene Blends

Directory of Open Access Journals (Sweden)

Ismael AMER

2016-09-01

Full Text Available The thermal, morphological and mechanical properties of polypropylene blends as influenced by the molecular weight and tacticity were investigated. Polypropylene sample blends (50/50 wt.% were injection moulded into standard disks for morphological and mechanical tests. The thermal properties of the polypropylene blends were measured by differential scanning calorimetry (DSC, while the morphological and mechanical properties of specimens were investigated by means of optical microscope (OM, scanning electron microscopy (SEM, microhardness (MH and dynamic mechanical analysis (DMA. DSC results of the bulk crystallization of the various isotactic polypropylene blends showed one melting peak, which indicates that cocrystallization of the blends occurred. However, the crystallization behavior of the polymer blends was strongly affected by the configuration (tacticity and molecular weight of the polypropylene polymers. In addition, the MH and DMA measurements showed that blends of two different isotactic polypropylenes presented MH and storage modulus values between the values of the respective two MH and storage modulus values of the homopolymer samples, which in turn, depended on the type and degree of the crystallinity of the blends. However, the presence of syndiotactic polypropylene in a blend with isotactic polypropylene leads to a decrease in the MH value of the isotactic polypropylene samples. Normal 0 19 false false false LT X-NONE X-NONE

Structural changes of PP with different isotacticity induced by γ-irradiation

International Nuclear Information System (INIS)

Wang Shaofeng; Wei Genshuan; Qiao Jinliang

2000-01-01

The morphology of i-PP with different isotacticity under high absorbed dose were studied with the measurements of crystallinity, crystallite size, melting heat and melting point by x-ray diffraction and DSC methods respectively. The results indicate that the changes are not only related to the heat history but also related to the isotacticity of i-PP. In generally, the higher the isotacticity of i-PP, the less morphology changes, and the morphology of annealing samples change less than the virgin powder samples. It means that the annealed i-PP with higher isotacticity is more stable to radiation both in air and vacuum conditions. (author)

Raman Spectroscopy of Isotactic Polypropylene-Halloysite Nanocomposites

Directory of Open Access Journals (Sweden)

Elamin E. Ibrahim

2012-01-01

Full Text Available Raman spectroscopy investigations on nanocomposites obtained by dispersing halloysite within isotactic polypropylene are reported. A detailed analysis of the modifications of the regularity band associated to the polymeric matrix is presented. The Raman lines assigned to the polymeric matrix are broadened and weakened as the loading with halloysite is increased. The analysis of Raman lines indicates that the polymeric matrix becomes less crystalline upon the loading with halloysite and that the nanofiller is experiencing a weak dehydration upon dispersion within the polymeric matrix, probably due to the related thermal processing used to achieve the dispersion of halloysite.

Phase separation of DMDBS from iPP, and controlled crystalline orientation

Science.gov (United States)

Sreenivas, K.; Kumaraswamy, Guruswamy; Basargekar, R. S.

2012-02-01

We report an unexpected dependence of DMDBS phase separation temperature on the molecular weight of the matrix isotactic polypropylene (iPP). DMDBS crystallizes out at lower temperatures for iPP with decreasing molecular weight (and correspondingly lower tacticity). This molecular weight dependence is unique to iPP, and is not observed for either syndiotactic PP or for random ethylene-PP copolymers. We show that thermodynamic Flory-type arguments are unable to rationalize the observed results. We also results on extrusion film casting of iPP containing DMDBS and show that flow-alignment of DMDBS networks template the orientation of PP crystals. The modulus and yield strength increase on addition of DMDBS, relative to the neat iPP. Tensile modulus and yield stress of drawn films increase with the degree of orientation, and we are able to achieve a substantial increase even at relatively low draw ratios.

Influence of the elastomeric polypropylene addition on the properties of commercial metallocenic polypropylene

Directory of Open Access Journals (Sweden)

Marques Maria de Fátima V.

2001-01-01

Full Text Available Polypropylene with special properties can be obtained by metallocenic catalysts. These catalytic systems represent the beginning of a new age in polyolefins technology. In this work, the influence of the addition of a syndiotactic polypropylene (s-PP on the processability and mechanical properties of a commercial isotactic polypropylene (i-PP obtained by metallocenic catalysts was evaluated. Increasing addition of s-PP promoted better processability, with an increase in the impact strength and a decrease in the stress at break. A reduction of the crystallinity in the polymeric blends was verified. The more significant influence of the s-PP addition was observed for the mi-PP, compared to the ZNi-PP.

Structural changes in the crystal-amorphous interface of isotactic polypropylene film induced by annealing and γ-irradiation

International Nuclear Information System (INIS)

Nishimoto, Sei-ichi; Seike, Hideo; Chaisupakitsin, M.; Yoshii, Fumio; Makuuchi, Keizo.

1995-01-01

Annealing and radiation effects on the microstructures of isotactic polypropylenes, homopolymer and ethylene (<2.3 wt%) incorporated random copolymers, in the solid state were studied to get mechanistic insight into the modification and degradation of mechanical properties. The growth of helical conformation of isotactic chains in the crystal-amorphous interface was induced to greater extent by γ-irradiation, while the transition from smectic to monoclinic modifications in the crystal phase occurred simultaneously by annealing. The yield stress of the polypropylene films increased with the increased content of helical conformation as the result of annealing and/or γ-irradiation. (author)

Chemical cross-linking of polypropylenes towards new shape memory polymers.

Science.gov (United States)

Raidt, Thomas; Hoeher, Robin; Katzenberg, Frank; Tiller, Joerg C

2015-04-01

In this work, syndiotactic polypropylene (sPP) as well as isotactic polypropylene (iPP) are cross-linked to gain a shape memory effect. Both prepared PP networks exhibit maximum strains of 700%, stored strains of up to 680%, and recoveries of nearly 100%. While x-iPP is stable for many cycles, x-sPP ruptures after the first shape-memory cycle. It is shown by wide-angle X-ray scattering (WAXS) experiments that cross-linked iPP exhibits homoepitaxy in the temporary, stretched shape but in contrast to previous reports it contains a higher amount of daughter than mother crystals. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of nano-scaled styrene butadiene rubber based nucleating agent on the thermal, crystallization and physical properties of isotactic polypropylene

Energy Technology Data Exchange (ETDEWEB)

Petchwattana, Nawadon [Division of Polymer Materials Technology, Faculty of Agricultural Product Innovation and Technology, Srinakharinwirot University, Sukhumvit 23, Wattana, Bangkok 10110 (Thailand); Covavisaruch, Sirijutaratana, E-mail: sirijutaratana.c@chula.ac.th [Department of Chemical Engineering, Faculty of Engineering, Chulalongkorn University, Pathumwan, Bangkok 10330 (Thailand); Sripanya, Panjapong [Thai Oleochemicals Company Limited (A Subsidiary of PTT Global Chemical Public Company Limited), Mueang Rayong, Rayong 21150 (Thailand)

2014-01-05

Highlights: • The effect of a SBR based β-NA on the properties iPP was investigated. • The addition of β-NA led to higher population of nuclei and smaller spherulites. • β to α phase transformation was observed when re-extrusion process was applied. • Impact strength was increased when the β-NA was added from 0.10 to 0.20 wt%. -- Abstract: The influence of a specific nano-scaled styrene butadiene rubber based β-nucleating agent (β-NA) on the properties of isotactic polypropylene (iPP) was investigated in the current research. β-NA was applied at the concentration ranged from 0.05 to 0.50 wt%. Microscopic observation revealed that the neat iPP crystals grew very slowly; they ranged in size from 100 to 200 μm. The addition of β-NA led to higher population of nuclei and smaller spherulites than those found in neat iPP. The addition of only 0.05 wt% β-NA significantly decreased the sizes of the spherulites down to 5 μm; the crystal grew very rapidly, leading to extremely fine morphology. Analysis by X-ray diffraction (XRD) confirmed that iPP/β-NA constituted mainly of β-crystal structure. The transformation of β to α phase was observed upon re-extrusion, it was verified by the lowered fraction of the β-crystalline phase (K{sub β}) although the total degree of crystallinity remained unchanged. A significant improvement in the impact strength of the iPP/β-NA was observed when the β-NA was employed from 0.10 to 0.20 wt%, leading to the formation of tough β-crystals in the β-NA nucleated iPP. The color measurement implied that the iPP nucleated with β-NA was superior in terms of whiteness but it was less transparent, as was evident by the increased haze.

Monotonic and cyclic responses of impact polypropylene and continuous glass fiber-reinforced impact polypropylene composites at different strain rates

KAUST Repository

Yudhanto, Arief

2016-03-08

Impact copolymer polypropylene (IPP), a blend of isotactic polypropylene and ethylene-propylene rubber, and its continuous glass fiber composite form (glass fiber-reinforced impact polypropylene, GFIPP) are promising materials for impact-prone automotive structures. However, basic mechanical properties and corresponding damage of IPP and GFIPP at different rates, which are of keen interest in the material development stage and numerical tool validation, have not been reported. Here, we applied monotonic and cyclic tensile loads to IPP and GFIPP at different strain rates (0.001/s, 0.01/s and 0.1/s) to study the mechanical properties, failure modes and the damage parameters. We used monotonic and cyclic tests to obtain mechanical properties and define damage parameters, respectively. We also used scanning electron microscopy (SEM) images to visualize the failure mode. We found that IPP generally exhibits brittle fracture (with relatively low failure strain of 2.69-3.74%) and viscoelastic-viscoplastic behavior. GFIPP [90]8 is generally insensitive to strain rate due to localized damage initiation mostly in the matrix phase leading to catastrophic transverse failure. In contrast, GFIPP [±45]s is sensitive to the strain rate as indicated by the change in shear modulus, shear strength and failure mode.

Solid-state drawing of post-consumer isotactic poly(propylene): Effect of melt filtration and carbon black on structural and mechanical properties.

Science.gov (United States)

Luijsterburg, B J; Jobse, P S; Spoelstra, A B; Goossens, J G P

2016-08-01

Post-consumer plastic waste obtained via mechanical recycling is usually applied in thick-walled products, because of the low mechanical strength due to the presence of contaminants. In fact, sorted post-consumer isotactic poly(propylene) (i-PP) can be considered as a blend of 95% i-PP and 5% poly(ethylene), with traces of poly(ethylene terephthalate) (PET). By applying a treatment such as solid-state drawing (SSD) after melt extrusion, the polymer chains can be oriented in one direction, thereby improving the stiffness and tensile strength. In this research, molecular processes such as crystal break-up and chain orientation of these complex blends were monitored as a function of draw ratio. The melt filter mesh size - used to exclude rigid PET particles - and the addition of carbon black (CB) - often added for coloration in the recycling industry - were varied to investigate their influence on the SSD process. This research shows that despite the blend complexity, the molecular processes during SSD compare to virgin i-PP and that similar draw ratios can be obtained (λmax=20), albeit at reduced stiffness and strength as a result of the foreign polymers present in post-consumer i-PP. It is observed that the process stability improves with decreasing mesh size and that higher draw ratios can be obtained. The addition of carbon black, which resides in the dispersed PE phase, also stabilizes the SSD process. Compared to isotropic post-consumer i-PP, the stiffness can be improved by a factor 10 to over 11GPa, while the tensile strength can be improved by a factor 15-385MPa, which is approx. 70% of the maximum tensile strength achieved for virgin i-PP. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study of gel formation in polypropylene modified by gamma irradiation

International Nuclear Information System (INIS)

Oliani, W.L.; Parra, D.F.; Fermino, D.M.; Lima, L.F.C.P.; Lugao, A.B.; Riella, H.G.

2010-01-01

The linearity of the chains of iPP (isotactic polypropylene) confers to this, low melt strength. This fact limits the use of iPP in processes that demand high stretching. The graft of branches confers improvements in its extensional viscosity, resulting in Polypropylene with High Melt Strength (HMS-PP). Preparation process of the HMS-PP, included iPP in pellets, conditioned in plastic container containing acetylene under pressure of 110 kPa and radiation with γ source of 60 Co in the doses of 5, 12.5 and 20 kGy. The gel fraction of the samples was determined by the extraction of soluble components in xylene under boiling for 12 hours at 138 deg C. The soluble part of the samples was decanted with the total volatilization of the xylene to the room temperature (25 deg C) and deposition in glass blades. These samples had been characterized by Optic Microscopy, Scanning Electron Microscopy and Infrared Spectroscopy. In this study of the morphology, we obtained the formation of gel and microgel of polypropylene with higher incidence in HMS-PP 20 kGy. (author)

Plasma modification of polypropylene surfaces and its alloying with styrene in situ

Energy Technology Data Exchange (ETDEWEB)

Ma Guiqiu, E-mail: magq@tju.edu.cn [School of Materials Science and Engineering, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin, 300072 (China); Liu Ben; Li Chen; Huang Dinghai; Sheng Jing [School of Materials Science and Engineering, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin, 300072 (China)

2012-01-15

The treatment of polypropylene surfaces has been studied by dielectric barrier discharges plasma of Ar. The structure and morphology of polypropylene surfaces of Ar plasma modification are characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectrometers and scanning electron microscope. The modified by plasma treatment of iPP (isotactic polypropylene) surface properties have been examined in a determination of free radicals. The modified active surfaces of polypropylene can induce grafting copolymerization of styrene onto polypropylene. The structure of grafting copolymer is characterized and the grafting percent of styrene onto polypropylene is calculated. The homopolymer of styrene can be formed under grafting copolymerization of styrene onto polypropylene, which follows that the alloying of polypropylene with styrene is achieved in situ.

Quantification of non-isothermal, multi-phase crystallization of isotactic polypropylene : the influence of shear and pressure

NARCIS (Netherlands)

Erp, van T.B.; Balzano, L.; Spoelstra, A.B.; Govaert, L.E.; Peters, G.W.M.

2012-01-01

Key issue in studying the crystallization process of semi-crystalline polymers, is the need for controlled (or known) boundary and initial conditions. Here dilatometry (PVT) is used to reveal the crystallization kinetics and the resulting morphology of isotactic polypropylene homopolymer as a

Mechanical and thermal behaviour of isotactic polypropylene reinforced with inorganic fullerene-like WS2 nanoparticles: Effect of filler loading and temperature

International Nuclear Information System (INIS)

Díez-Pascual, Ana M.; Naffakh, Mohammed

2013-01-01

The thermal and mechanical behaviour of isotactic polypropylene (iPP) nanocomposites reinforced with different loadings of inorganic fullerene-like tungsten disulfide (IF-WS 2 ) nanoparticles was investigated. The IF-WS 2 noticeably enhanced the polymer stiffness and strength, ascribed to their uniform dispersion, the formation of a large nanoparticle–matrix interface combined with a nucleating effect on iPP crystallization. Their reinforcement effect was more pronounced at high temperatures. However, a drop in ductility and toughness was found at higher IF-WS 2 concentrations. The tensile behaviour of the nanocomposites was extremely sensitive to the strain rate and temperature, and their yield strength was properly described by the Eyring's equation. The activation energy increased while the activation volume decreased with increasing nanoparticle loading, indicating a reduction in polymer chain motion. The nanoparticles improved the thermomechanical properties of iPP: raised the glass transition and heat deflection temperatures while decreased the coefficient of thermal expansion. The nanocomposites also displayed superior flame retardancy with longer ignition time and reduced peak heat release rate. Further, a gradual rise in thermal conductivity was found with increasing IF-WS 2 loading both in the glassy and rubbery states. The results presented herein highlight the benefits and high potential of using IF-nanoparticles for enhancing the thermomechanical properties of thermoplastic polymers compared to other nanoscale fillers. - Graphical abstract: Display Omitted - Highlights: • The thermal and mechanical behaviour of iPP/IF-WS 2 nanocomposites was studied. • Low IF-WS 2 contents provide a good balance between stiffness, strength and toughness. • Their tensile behaviour is sensitive to the strain rate and temperature. • The nanocomposites exhibit superior thermal conductivity and flame retardancy than iPP. • The benefits of using IF-WS 2 compared

Spray-Dried Cellulose Nanofibril-Reinforced Polypropylene Composites for Extrusion-Based Additive Manufacturing: Nonisothermal Crystallization Kinetics and Thermal Expansion

Directory of Open Access Journals (Sweden)

Lu Wang

2018-02-01

Full Text Available Isotactic polypropylene (iPP is a versatile polymer. It accounts for the second-largest polymer consumption worldwide. However, iPP is difficult to 3D print via extrusion-based processing. This is attributable to its rapid crystallization rate. In this study, spray-dried cellulose nanofibrils (SDCNF and maleic anhydride polypropylene (MAPP were investigated to reveal their effects on the nonisothermal crystallization kinetics and thermal expansion of iPP. SDCNF at 3 wt % and 30 wt % accelerated the crystallization rate of iPP, while SDCNF at 10 wt % retarded the crystallization rate by restricting crystal growth and moderately increasing the nucleation density of iPP. Additionally, adding MAPP into iPP/SDCNF composites accelerated the crystallization rate of iPP. The effective activation energy of iPP increased when more than 10 wt % SDCNF was added. Scanning electron microscopy and polarized light microscopy results indicated that high SDCNF content led to a reduced gap size among SDCNF, which hindered the iPP crystal growth. The coefficient of thermal expansion of iPP/SDCNF10% was 11.7% lower than the neat iPP. In summary, SDCNF, at 10 wt %, can be used to reduce the warping of iPP during extrusion-based additive manufacturing.

The effect of annealing on the time-dependent behavior of isotactic polypropylene at finite strains

DEFF Research Database (Denmark)

Drozdov, Aleksey D.; Christiansen, Jesper de Claville

2002-01-01

Four series of tensile relaxation tests are performed on isotactic polypropylene at elongations up to the necking point. In the first series of experiments, injection-molded samples are used without thermal pre-treatment. In the other series, the specimens are annealed for 24 h prior to testing a...... at annealing. In the post-critical region (large strains), an increase in the fraction of active amorphous domains is attributed to disintegration of primary (thick) lamellae....

Online interferometric study of viscoelastic rupture and necking deformation of as-spun (iPP) fibres due to creep process.

Science.gov (United States)

Sokkar, Taha; El-Farahaty, Kermal; Azzam, Amira

2015-01-01

Creep deformation under constant load leads to rupture when the polymer chains can no longer separate and accommodate the load. This fracture phenomenon is investigated interferometrically. The creep behaviour of as-spun isotactic Polypropylene (iPP) fibres is studied at different stresses, different initial lengths and different radii. The creep rate, which defines the velocity of the creep deformation and the dimensional stability of the material, is studied. The failure time and stress of iPP due to creep process is determined. The necking deformation was in situ detected during creep process. The mean refractive indices (n(P) andn⊥) profiles of iPP fibres were determined at different positions along the fibre axis before and after necking. The relation between the creep behaviour and different optical and structural parameters is investigated. Microinterferograms are given for illustration. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

Fabrication of polypropylene/silver nanocomposites for biocidal applications

Energy Technology Data Exchange (ETDEWEB)

Oliani, Washington Luiz, E-mail: washoliani@usp.br [Nuclear and Energy Research Institute, IPEN-CNEN/SP, Av. Prof. Lineu Prestes, 2242 – Cidade Universitária – CEP, 05508-000 São Paulo (Brazil); Parra, Duclerc Fernandes; Komatsu, Luiz Gustavo Hiroki [Nuclear and Energy Research Institute, IPEN-CNEN/SP, Av. Prof. Lineu Prestes, 2242 – Cidade Universitária – CEP, 05508-000 São Paulo (Brazil); Lincopan, Nilton [Department of Microbiology, Institute of Biomedical Sciences, University of Sao Paulo, 05508-000, São Paulo (Brazil); Department of Clinical Analysis, School of Pharmacy, University of São Paulo, 05508-000, São Paulo (Brazil); Rangari, Vijaya Kumar [Department of Materials Science and Engineering, Tuskegee University, AL 36088 (United States); Lugao, Ademar Benevolo [Nuclear and Energy Research Institute, IPEN-CNEN/SP, Av. Prof. Lineu Prestes, 2242 – Cidade Universitária – CEP, 05508-000 São Paulo (Brazil)

2017-06-01

This paper presents a study on biocidal effect of polymer nanocomposite films of gamma irradiated polypropylene (PP) and silver nanoparticles. The modified polypropylene was obtained from isotactic polypropylene (iPP) in pellets form by irradiation with gamma rays in the presence of acetylene. A new morphology with long chain branching of PP and distinct rheology is obtained by this process. The blend of 50/50 wt% neat PP and PP modified by gamma radiation were further mixed using a twin screw extruder. The AgNPs were infused into this polymer blend at different concentrations of: 0.1%; 0.25%; 0.5%; 1.0%; 1.0% (PVP), 2.0% and 4.0% by wt%. These polymer nanocomposites were characterized by Raman spectroscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), thermogravimetric analysis (TG), differential scanning calorimetry (DSC), X-ray diffraction (XRD), transmission electron microscopy (TEM), cytotoxicity test and Kirby-Bauer disk diffusion techniques. The bactericidal effect of Pseudomonas aeruginosa (P. aeruginosa) and Staphylococcus aureus (S. aureus) were assessed in detail. - Highlights: • PP film was obtained from iPP in pellets form by γ rays with acetylene and AgNPs • Bactericidal effect of P aeruginosa and S aureus were assessed.

Transparent Low Electrostatic Charge Films Based on Carbon Nanotubes and Polypropylene. Homopolymer Cast Films

Directory of Open Access Journals (Sweden)

Zoe Vineth Quiñones-Jurado

2018-01-01

Full Text Available Use of multi-wall carbon nanotubes (MWCNTs in external layers (A-layers of ABA-trilayer polypropylene films was investigated, with the purpose of determining intrinsic and extrinsic factors that could lead to antistatic behavior of transparent films. The incorporation of 0.01, 0.1, and 1 wt % of MWCTNs in the A-layers was done by dilution through the masterbatch method. Masterbatches were fabricated using isotactic polypropylene (iPP with different melt flow indexes 2.5, 34, and 1200 g/10 min, and using different ultrasound assist methods. It was found that films containing MWCNTs show surface electrical resistivity of 1012 and 1016 Ω/sq, regardless of the iPP melt flow index (MFI and masterbatch fabrication method. However, electrostatic charge was found to depend upon the iPP MFI, the ultrasound assist method and MWCNT concentration. A percolation electron transport mechanism was determined most likely responsible for this behavior. Optical properties for films containing MWCNTs do not show significant differences compared to the reference film at MWCNT concentrations below 0.1 wt %. However, an enhancement in brightness was observed, and it was attributed to ordered iPP molecules wrapping the MWCNTs. Bright transparent films with low electrostatic charge were obtained even for MWCNTs concentrations as low as 0.01 wt %.

Study of gel formation in polypropylene modified by gamma irradiation; Estudo da formacao de geis em polipropileno modificado por irradiacao gama

Energy Technology Data Exchange (ETDEWEB)

Oliani, W.L.; Parra, D.F.; Fermino, D.M.; Lima, L.F.C.P.; Lugao, A.B., E-mail: washoliani@usp.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Riella, H.G. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2010-07-01

The linearity of the chains of iPP (isotactic polypropylene) confers to this, low melt strength. This fact limits the use of iPP in processes that demand high stretching. The graft of branches confers improvements in its extensional viscosity, resulting in Polypropylene with High Melt Strength (HMS-PP). Preparation process of the HMS-PP, included iPP in pellets, conditioned in plastic container containing acetylene under pressure of 110 kPa and radiation with {gamma} source of {sup 60}Co in the doses of 5, 12.5 and 20 kGy. The gel fraction of the samples was determined by the extraction of soluble components in xylene under boiling for 12 hours at 138 deg C. The soluble part of the samples was decanted with the total volatilization of the xylene to the room temperature (25 deg C) and deposition in glass blades. These samples had been characterized by Optic Microscopy, Scanning Electron Microscopy and Infrared Spectroscopy. In this study of the morphology, we obtained the formation of gel and microgel of polypropylene with higher incidence in HMS-PP 20 kGy. (author)

Broad line .sup.1./sup.H NMR study of polymer blend composed of isotactic polypropylene and ethylene-propylene-diene terpolymer

Czech Academy of Sciences Publication Activity Database

Olčák, D.; Mucha, L.; Onufer, J.; Raab, Miroslav; Spěváček, Jiří

2002-01-01

Roč. 2, č. 3 (2002), s. 31-35 ISSN 1335-8243 R&D Projects: GA ČR GA106/02/1249 Grant - others:GA SK(SK) 1/7402/20 Institutional research plan: CEZ:AV0Z4050913 Keywords : isotactic polypropylene * EPDM rubber * polymer blend Subject RIV: JJ - Other Materials

Effects of the cooling rate on the shear behavior of continuous glass fiber/impact polypropylene composites (GF-IPP)

KAUST Repository

Wafai, Husam

2016-09-20

Fiber-reinforced composites with improved dissipation of energy during impact loading have recently been developed based on a polypropylene copolymer commonly called impact polypropylene (IPP). Composites made of IPP reinforced with glass fibers (GF) are particularly attractive to the automotive industry due to their low cost and good impact resistance. In such composites, the cooling rate varies depending on processing techniques and manufacturing choices. Here, we study the effects of the cooling rate of GF-IPP composites on shear behavior, which is critical in impact applications, using [±45]s monotonic and cyclic (load/unload) tensile specimens. The specimens were manufactured under a wide range of cooling rates (3 °C/min, 22 °C/min, 500–1000 °C/min). Mainly dominated by the properties of the matrix, the global shear behavior of GF-IPP composites differed considerably with respect to the cooling rate. However, the performance of the fiber-matrix interface (chemically modified) appeared to be unaffected by the range of cooling rates used in this study. We found that the cooling rate has a minor effect on the rate of damage accumulation, while it strongly modifies the shear-activated rate-dependant viscoelastic behavior. © 2016 Elsevier Ltd

Dielectric and thermal properties of isotactic polypropylene/hexagonal boron nitride composites for high-frequency applications

International Nuclear Information System (INIS)

Takahashi, Susumu; Imai, Yusuke; Kan, Akinori; Hotta, Yuji; Ogawa, Hirotaka

2014-01-01

Highlights: • The degree of orientation of the hBN could be controlled by the fabrication process. • The dielectric constants of composites ranged between 2.25 and 3.39. • The dielectric loss of composites was on the order of 10 −4 for all compositions. • The thermal conductivity were improved by controlling orientation of hBN. - Abstract: Dielectric composites aimed for high frequency applications were prepared by using anisotropic hexagonal boron nitride (hBN) particles as a fillers and isotactic polypropylene (iPP) as polymer matrix. Dielectric and thermal properties of the composites were studied, focusing on the filler orientation in the plate-shape specimens and filler concentration up to 40 vol%. The degree of orientation of the filler was controlled by the composite fabrication process. Hot-pressing gave relatively random orientation of the filler in the matrix, while injection molding induced a high orientation. Dielectric constant (ε r ) of the composites ranged between 2.25 and 3.39. The estimation of ε r based on the Bruggeman mixing model agreed well with the measured value. Low dielectric losses (tan δ) at microwave frequencies, on the order of 10 −4 , were obtained for all the compositions. Through-thickness thermal conductivity (k) of the hot-pressed samples showed a drastic increase with increasing the filler concentration, reaching up to 2.1 W/m K at 40 vol% of hBN. The filler concentration dependence of k was less significant for the injection molded composites. In-plane thermal expansion was almost independent on the filler orientation, while the coefficient of thermal expansion for the thickness direction of the hot-pressed sample was reduced to approximately half of the injection molded counterpart. These differences in thermal conductivity and thermal expansion are thought to arise from the difference in hBN filler orientation

Comparison of chemical changes during photooxidation of polypropylene film and filament containing phthalocyanine pigment

International Nuclear Information System (INIS)

Ahmadi, Z.; Haghighat Kish, M.; Kotak, R.; Katbab, A. A.

2008-01-01

Photooxidation as an important process, which significantly affects the service life of the polypropylene products, has been the subject of much theoretical and experimental study. Pigments used often change the light stabilities of polypropylene. Out-door applications of pigmented polypropylene are now increasingly developed in products such as artificial grass. The aim of this work is to examine the effect of photo-oxidation on the structure of isotactic polypropylene (iPP) in film and filament forms, where phthalocyanine pigment is used. For production of films and filaments, iPP granules with MFI 25 g/10 min were used, with and without phthalocyanine pigment. Samples were exposed to xenon lamp for various time lengths. The extent of the changes in chemical and structural parameters was examined by differential scanning calorimetry, Fourier transform infrared spectroscopy and wide angle x-ray diffraction. The results show that carbonyl and hydroperoxide indices increase during the exposure to the radiation. The changes in melting points of the samples were not significant after irradiation process. The effects of phthalocyanine pigment in the photooxidation of film and filament were different. Crystalline fractions of the non-pigmented filament samples decreased during the irradiation time while increased in film samples. Build up of hydroperoxide and carbonyl group in filament was higher than in film samples; that could be due to the differences in structural parameters. Crystallinity variations during photooxidation are related to the nucleation effect of the pigment, chemical crystallization and phase transformation

Comparison of Chemical Changes During Photooxidation of Polypropylene Film and Filament Containing Phthalocyanine Pigment

Directory of Open Access Journals (Sweden)

Z. Ahmadi

2008-02-01

Full Text Available Photooxidation as an important process, which significantly affects the service life of the polypropylene products, has been the subject of much theoretical and experimental study. Pigments used often change the light stabilities of polypropylene. Out-door applications of pigmented polypr-opylene are now increasingly developed in products such as artificial grass. The aim of this work is to examine the effect of photo-oxidation on the structure of isotactic polypropylene (iPP in film and filament forms, where phthalocyanine pigment is used. For production of films and filaments, iPP granules with MFI 25 g/10min were used, with and without phthalocyanine pigment. Samples were exposed to xenon lamp for various time lengths. The extent of the changes in chemical and structural parameters was examined by differential scanning calorimetry, Fourier transform infrared spectroscopy and wide angle x-ray diffraction. The results show that carbonyl and hydroperoxide indices increase during the exposure to the radiation. The changes in melting points of the samples were not significant after irradiation process. The effects of phthalocyanine pigment in the photooxidation of filmand filament were different. Crystalline fractions of the non-pigmented filament samples decreased during the irradiation time while increased in film samples. Build up of hydroperoxide and carbonyl group in filament was higher than in film samples; that could be due to the differences in structural parameters. Crystallinity variations during photooxidation are related to the nucleation effect of the pigment, chemical crystallization and phase transformation.

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains

DEFF Research Database (Denmark)

Drozdov, Aleksey D.; Christiansen, Jesper de Claville

2002-01-01

prior to testing. A constitutive model is developed for the viscoplastic behavior of isotactic polypropylene at finite strains. A semicrystalline polymer is treated as equivalent heterogeneous network of chains bridged by permanent junctions (physical cross-links and entanglements). The network...... is thought of as an ensemble of meso-regions connected with each other by links (lamellar blocks). In the sub-yield region of deformations, junctions between chains in meso-domains slide with respect to their reference positions (which reflects sliding of nodes in the amorphous phase and fine slip...... responses of non-annealed and annealed specimens: (i) necking of samples not subjected to thermal treatment precedes coarse slip and fragmentation of lamellar blocks, whereas cold-drawing of annealed specimens up to a longitudinal strain of 80% does not induce spatial heterogeneity of their deformation; (ii...

100 MeV Ag{sup 7+} ion induced physicochemical changes in isotactic polypropylene

Energy Technology Data Exchange (ETDEWEB)

Mathakari, N.L. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Ganeshkhind, Pune 411007, Maharashtra (India); Kanjilal, D. [Inter University Accelerator Center, New Delhi (India); Bhoraskar, V.N. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Ganeshkhind, Pune 411007, Maharashtra (India); Dhole, S.D. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Ganeshkhind, Pune 411007, Maharashtra (India)], E-mail: sanjay@physics.unipune.ernet.in

2008-04-15

Thin films of isotactic polypropylene having 500 {mu}m thickness were irradiated with 100 MeV Ag{sup 7+} ions at the fluences varying from 10{sup 11} to 5 x 10{sup 12} ions/cm{sup 2}. The properties such as chemical, optical, structural and surface morphology were characterized by techniques namely FTIR, UV-visible, photoluminescence, XRD, SEM and contact angle method. The FTIR spectra show the scissioning of C-H and C-C bonds, whereas, in photoluminescence, the intensities of the peaks at 440 and 480 nm in emission spectra and at 236 nm in excitation spectra observed to be decreased with increase in ion fluence. This may be due to the decomposition of luminescent centers. The UV-visible spectra also show a remarkable red shift from 218 to 367 nm and the subsequent large reduction in the optical band gap from 5.37 to 3.39 eV. This attributes to the carbonization or graphitization of polypropylene. On the contrary, the intensities of XRD peaks, particularly the peak due to 1 1 0 planes, shows sufficient enhancement which signifies overall increase in crystallinity. This ascribes to relief in the local strain on the crystallites due to scissioning of tie molecules in the amorphous zones. The contact angle has increased from 78 deg. to 97 deg. which reveals the absence of hydrophilic functional groups, carbonization and surface roughening. The result is also supported by SEM analysis.

Application of waste bulk moulded composite (BMC) as a filler for isotactic polypropylene composites.

Science.gov (United States)

Barczewski, Mateusz; Matykiewicz, Danuta; Andrzejewski, Jacek; Skórczewska, Katarzyna

2016-05-01

The aim of this study was to produce isotactic polypropylene based composites filled with waste thermosetting bulk moulded composite (BMC). The influence of BMC waste addition (5, 10, 20 wt%) on composites structure and properties was investigated. Moreover, additional studies of chemical treatment of the filler were prepared. Modification of BMC waste by calcium stearate (CaSt) powder allows to assess the possibility of the production of composites with better dispersion of the filler and more uniform properties. The mechanical, processing, and thermal properties, as well as structural investigations were examined by means of static tensile test, Dynstat impact strength test, differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), melt flow index (MFI) and scanning electron microscopy (SEM). Developed composites with different amounts of non-reactive filler exhibited satisfactory thermal and mechanical properties. Moreover, application of the low cost modifier (CaSt) allows to obtain composites with better dispersion of the filler and improved processability.

Morphology of Thermoplastic Elastomers:Stereoblock Polypropylene

Energy Technology Data Exchange (ETDEWEB)

Pople, John A

2002-08-06

The morphologies of low-density (0.86 g/cm{sup 3}), elastomeric polypropylene (ePP) derived from bis(2-arylindenyl) hafnium dichloride were investigated using a combination of polarized optical microscopy (OM), differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), Fourier transform infrared (FT-IR) spectroscopy, and tapping mode atomic force microscopy (TMAFM). These low-crystallinity polypropylenes, when crystallized isothermally from the melt, exhibit morphologies reminiscent of classical semi-crystalline polymers. The presence of lamellae, cross-hatching, hedrites, and spherulites was revealed by high resolution TM-AFM. These elastomeric polypropylenes can be fractionated into components of different average tacticities and crystallinities, but similar molecular mass. The analysis of the morphologies of all of the fractions revealed both large hierarchical structures and cross-hatching typical of the {alpha}-modification of crystalline isotactic polypropylene for all but the lowest crystalline ether soluble fraction. Evidence for high-melting crystals in all of the fractions are most consistent with a stereoblock microstructure of atactic and isotactic sequences.

Metamaterial Behavior of Polymer Nanocomposites Based on Polypropylene/Multi-Walled Carbon Nanotubes Fabricated by Means of Ultrasound-Assisted Extrusion

Directory of Open Access Journals (Sweden)

Juan C. Pérez-Medina

2016-11-01

Full Text Available Metamaterial behavior of polymer nanocomposites (NCs based on isotactic polypropylene (iPP and multi-walled carbon nanotubes (MWCNTs was investigated based on the observation of a negative dielectric constant (ε′. It is demonstrated that as the dielectric constant switches from negative to positive, the plasma frequency (ωp depends strongly on the ultrasound-assisted fabrication method, as well as on the melt flow index of the iPP. NCs were fabricated using ultrasound-assisted extrusion methods with 10 wt % loadings of MWCNTs in iPPs with different melt flow indices (MFI. AC electrical conductivity (σ(AC as a function of frequency was determined to complement the electrical classification of the NCs, which were previously designated as insulating (I, static-dissipative (SD, and conductive (C materials. It was found that the SD and C materials can also be classified as metamaterials (M. This type of behavior emerges from the negative dielectric constant observed at low frequencies although, at certain frequencies, the dielectric constant becomes positive. Our method of fabrication allows for the preparation of metamaterials with tunable ωp. iPP pure samples show only positive dielectric constants. Electrical conductivity increases in all cases with the addition of MWCNTs with the largest increases observed for samples with the highest MFI. A relationship between MFI and the fabrication method, with respect to electrical properties, is reported.

Metamaterial Behavior of Polymer Nanocomposites Based on Polypropylene/Multi-Walled Carbon Nanotubes Fabricated by Means of Ultrasound-Assisted Extrusion

Science.gov (United States)

Pérez-Medina, Juan C.; Waldo-Mendoza, Miguel A.; Cruz-Delgado, Víctor J.; Quiñones-Jurado, Zoe V.; González-Morones, Pablo; Ziolo, Ronald F.; Martínez-Colunga, Juan G.; Soriano-Corral, Florentino; Avila-Orta, Carlos A.

2016-01-01

Metamaterial behavior of polymer nanocomposites (NCs) based on isotactic polypropylene (iPP) and multi-walled carbon nanotubes (MWCNTs) was investigated based on the observation of a negative dielectric constant (ε′). It is demonstrated that as the dielectric constant switches from negative to positive, the plasma frequency (ωp) depends strongly on the ultrasound-assisted fabrication method, as well as on the melt flow index of the iPP. NCs were fabricated using ultrasound-assisted extrusion methods with 10 wt % loadings of MWCNTs in iPPs with different melt flow indices (MFI). AC electrical conductivity (σ(AC)) as a function of frequency was determined to complement the electrical classification of the NCs, which were previously designated as insulating (I), static-dissipative (SD), and conductive (C) materials. It was found that the SD and C materials can also be classified as metamaterials (M). This type of behavior emerges from the negative dielectric constant observed at low frequencies although, at certain frequencies, the dielectric constant becomes positive. Our method of fabrication allows for the preparation of metamaterials with tunable ωp. iPP pure samples show only positive dielectric constants. Electrical conductivity increases in all cases with the addition of MWCNTs with the largest increases observed for samples with the highest MFI. A relationship between MFI and the fabrication method, with respect to electrical properties, is reported. PMID:28774042

Cyclic viscoelastoplasticity of polypropylene/nanoclay composites

DEFF Research Database (Denmark)

Drozdov, A.; Christiansen, Jesper de Claville

2012-01-01

Observations are reported on isotactic polypropylene/organically modified nanoclay hybrids with concentrations of filler ranging from 0 to 5 wt.% in cyclic tensile tests with a stress–controlled program (oscillations between various maximum stresses and the zero minimum stress). A pronounced effe...

Mechanical and dielectric characterization of hemp fibre reinforced polypropylene (HFRPP by dry impregnation process

Directory of Open Access Journals (Sweden)

2010-03-01

Full Text Available Natural fibres such as jute, coir, sisal, bamboo and pineapple are known to have high specific strength and can be effectively used in composites in various applications. The use of hemp fibres to reinforce the polymer aroused great interest and expectations amongst scientists and materials engineers. In this paper, composites with isotactic polypropylene (iPP matrix and hemp fibres were studied. These materials were manufactured via the patented FIBROLINE process based on the principle of the dry impregnation of a fibre assembly with a thermoplastic powder (iPP, using an alternating electric field. The aim of this paper is to show the influence of fibre/matrix interfaces on dielectric properties coupled with mechanical behaviours. Fibres or more probably the fibre/matrix interfaces allow the diffusion of electric charges and delocalise the polarisation energy. In this way, damages are limited during mechanical loading and the mechanical properties of the composites increase. The structure of composite samples was investigated by X-ray and FTIR analysis. The mechanical properties were analysed by quasistatic and dynamic tests. The dielectric investigations were carried out using the SEMME (Scanning Electron Microscope Mirror Effect method coupled with the measurement of the induced current (ICM.

Crystallization and melting behavior of isotactic polypropylene composites filled by zeolite supported β-nucleator

International Nuclear Information System (INIS)

Jiang, Juan; Li, Gu; Tan, Nanshu; Ding, Qian; Mai, Kancheng

2012-01-01

Highlights: ► The supported calcium pimelate β-zeolite was prepared. ► The β-nucleation of zeolite was enhanced dramatically through reaction. ► High β-phase content iPP composites were obtained by introducing the β-zeolite into iPP. - Abstract: In order to prepare the zeolite filled β-iPP composites, the calcium pimelate as β-nucleator supported on the surface of zeolite (β-zeolite) was prepared by the interaction between calcified zeolite and pimelic acid. The β-nucleation, crystallization behavior and melting characteristic of zeolite, calcified zeolite and β-zeolite filled iPP composites were investigated by differential scanning calorimetry and wide-angle X-ray diffractometer. The results indicated that addition of the zeolite and calcified zeolite as well as β-zeolite increased the crystallization temperature of iPP. The zeolite and calcified zeolite filled iPP composites mainly crystallized in the α-crystal form and the strong β-heterogeneous nucleation of β-zeolite results in the formation of only β-crystal in β-zeolite filled iPP composites. The zeolite filled β-iPP composites with high β-crystal contents (above 0.90) can be easily obtained by adding β-zeolite into iPP matrix.

Radiation resistant polypropylene blended with mobilizer,. antioxidants and nucleating agent

Science.gov (United States)

Shamshad, A.; Basfar, A. A.

2000-03-01

Post-irradiation storage of medical disposables prepared from isotactic polypropylene renders them brittle due to degradation. To avoid this, isotactic polypropylene [(is)PP] was blended with a mobilizer, dioctyl pthallate (DOP), three antioxidants (hindered amines and a secondary antioxidant) and benzoic acid to obtain radiation-resistant, thermally-stable and transparent material. Different formulations prepared were subjected to gamma radiation to doses of 25 and 50 kGy. Tests of breakage on bending after ageing in an oven at 70°C up to 12 months have shown that the addition of DOP and the antioxidants imparts improved radiation and thermal stability as compared to (is)PP alone or its blend with DOP. All the formulations irradiated or otherwise demonstrated excellent colour stability even after accelerated ageing at 70°C for prolonged periods.

Thermal aging and accelerated weathering of HMSPP: structural and morphological studies

International Nuclear Information System (INIS)

Oliani, Washington L.; Komatsu, Luiz G.H.; Parra, Duclerc F.

2015-01-01

This work focuses of the influence of weathering factors - UV radiation, humidity, and temperature on the structure and morphology polypropylene with high melt strength (HMSPP), also called polypropylene modified by irradiation. The HMSPP was prepared from iPP (isotactic polypropylene) in presence of acetylene at 110 kPa pressure and irradiated with γ of "6"0Co at doses of 5, 12.5 and 20 kGy. It has been observed that HMSPP deteriorates the weathering resistance, the thermal behavior and the long-term stability of HMSPP, beyond substantial color changes. The samples aged were characterized by infrared spectroscopy (FTIR), optical microscopy (OM) and differential scanning calorimetry (DSC). The optical microscopy images on the surface show that thermal aging and artificial weathering proceed by different mechanisms. The effects of elevated temperature aging were evaluated in HMSPPs exposed surface according to the order: HMSPP 20 >12.5 > kGy >iPP, showing intense crack formation in surface exposed due to thermo oxidative degradation. (author)

A novel test method for quantifying surface tack of polypropylene compound surfaces

Directory of Open Access Journals (Sweden)

2011-11-01

Full Text Available While adhesiveness is required for polymer surfaces in special applications, tacky surfaces are generally undesirable in many applications like automotive interior parts. The tackiness of polymer surface results from a combination of composition and additivation, and it can change significantly in natural or accelerated ageing. Since there is no established, uniform method to characterize surface tack, the major focus of the present work was on the development of an objective quantification method. A setup having a soft die tip attached to a standard tensile tester was developed aiming for correlation to the human sense of touch. Three different model thermoplastic polyolefin (TPO compound formulations based on a high-impact isotactic polypropylene (iPP composition with varying amounts and types of anti-scratch additives were used for these investigations. As the surface tack phenomenon is related to ageing and weathering, the material’s examination was also performed after various intervals of weathering. The developed method allows a fast assessment of the effect of polymer composition variations and different additive formulations on surface tack and gives identical rankings as the standardized haptic panel.

Ultrasound-Assist Extrusion Methods for the Fabrication of Polymer Nanocomposites Based on Polypropylene/Multi-Wall Carbon Nanotubes

Science.gov (United States)

Ávila-Orta, Carlos A.; Quiñones-Jurado, Zoe V.; Waldo-Mendoza, Miguel A.; Rivera-Paz, Erika A.; Cruz-Delgado, Víctor J.; Mata-Padilla, José M.; González-Morones, Pablo; Ziolo, Ronald F.

2015-01-01

Isotactic polypropylenes (iPP) with different melt flow indexes (MFI) were used to fabricate nanocomposites (NCs) with 10 wt % loadings of multi-wall carbon nanotubes (MWCNTs) using ultrasound-assisted extrusion methods to determine their effect on the morphology, melt flow, and electrical properties of the NCs. Three different types of iPPs were used with MFIs of 2.5, 34 and 1200 g/10 min. Four different NC fabrication methods based on melt extrusion were used. In the first method melt extrusion fabrication without ultrasound assistance was used. In the second and third methods, an ultrasound probe attached to a hot chamber located at the exit of the die was used to subject the sample to fixed frequency and variable frequency, respectively. The fourth method is similar to the first method, with the difference being that the carbon nanotubes were treated in a fluidized air-bed with an ultrasound probe before being used in the fabrication of the NCs with no ultrasound assistance during extrusion. The samples were characterized by MFI, Optical microscopy (OM), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), electrical surface resistivity, and electric charge. MFI decreases in all cases with addition of MWCNTs with the largest decrease observed for samples with the highest MFI. The surface resistivity, which ranged from 1013 to 105 Ω/sq, and electric charge, were observed to depend on the ultrasound-assisted fabrication method as well as on the melt flow index of the iPP. A relationship between agglomerate size and area ratio with electric charge was found. Several trends in the overall data were identified and are discussed in terms of MFI and the different fabrication methods. PMID:28793686

Ultrasound-Assist Extrusion Methods for the Fabrication of Polymer Nanocomposites Based on Polypropylene/Multi-Wall Carbon Nanotubes

Directory of Open Access Journals (Sweden)

Carlos A. Ávila-Orta

2015-11-01

Full Text Available Isotactic polypropylenes (iPP with different melt flow indexes (MFI were used to fabricate nanocomposites (NCs with 10 wt % loadings of multi-wall carbon nanotubes (MWCNTs using ultrasound-assisted extrusion methods to determine their effect on the morphology, melt flow, and electrical properties of the NCs. Three different types of iPPs were used with MFIs of 2.5, 34 and 1200 g/10 min. Four different NC fabrication methods based on melt extrusion were used. In the first method melt extrusion fabrication without ultrasound assistance was used. In the second and third methods, an ultrasound probe attached to a hot chamber located at the exit of the die was used to subject the sample to fixed frequency and variable frequency, respectively. The fourth method is similar to the first method, with the difference being that the carbon nanotubes were treated in a fluidized air-bed with an ultrasound probe before being used in the fabrication of the NCs with no ultrasound assistance during extrusion. The samples were characterized by MFI, Optical microscopy (OM, Scanning electron microscopy (SEM, Transmission electron microscopy (TEM, electrical surface resistivity, and electric charge. MFI decreases in all cases with addition of MWCNTs with the largest decrease observed for samples with the highest MFI. The surface resistivity, which ranged from 1013 to 105 Ω/sq, and electric charge, were observed to depend on the ultrasound-assisted fabrication method as well as on the melt flow index of the iPP. A relationship between agglomerate size and area ratio with electric charge was found. Several trends in the overall data were identified and are discussed in terms of MFI and the different fabrication methods.

Origin of toughness in .beta.-polypropylene: the effect of molecular mobility in the amorphous phase

Czech Academy of Sciences Publication Activity Database

Policianová, Olivia; Hodan, Jiří; Brus, Jiří; Kotek, Jiří

2015-01-01

Roč. 60, 9 March (2015), s. 107-114 ISSN 0032-3861 R&D Projects: GA ČR(CZ) GA13-29009S Institutional support: RVO:61389013 Keywords : isotactic polypropylene * β-modification * toughness Subject RIV: JI - Composite Materials Impact factor: 3.586, year: 2015

Interfacial enhancement of polypropylene composites modified with sorbitol derivatives and siloxane-silsesquioxane resin

Science.gov (United States)

Dobrzyńska-Mizera, Monika; Dutkiewicz, Michał; Sterzyński, Tomasz; Di Lorenzo, Maria Laura

2015-12-01

Composites based on polypropylene (iPP) modified with a sorbitol derivative (NX8000) and siloxane-silsesquioxane resin (SiOPh) containing maleated polypropylene (MAPP) as compatibilizer were prepared by melt extrusion. Calorimetric investigations were carried out using differential scanning calorimetry (DSC), whereas the morphological and mechanical properties were investigated by scanning electron microscopy (SEM) and static tensile tests. DSC measurements revealed no influence of SiOPh and a slight effect of MAPP addition on the crystallization kinetics of polypropylene. Additionally, the introduction of MAPP into the iPP+NX8000+SiOPh composites increased plastic properties of the samples. All the above was attributed to the compatibilizing effect of MAPP which improved interfacial adhesion between iPP, NX8000 and SiOPh. This phenomenon was also confirmed by the SEM images illustrating more homogenous distribution of the filler in the compatibilized samples.

Properties and Semicrystalline Structure Evolution of Polypropylene/Montmorillonite Nanocomposites under Mechanical Load

DEFF Research Database (Denmark)

Stribeck, Norbert; Zeinolebadi, Ahmad; Ganjaee Sari, Morteza

2012-01-01

Small-angle X-ray scattering (SAXS) monitors tensile and load-cycling tests of metallocene isotactic polypropylene (PP), a blend of PP and montmorillonite (MMT), and two block copolymer compatibilized PP/MMT nanocomposites. Mechanical properties of the materials are similar, but the semicrystalline......%. Other results concern the evolution of Strobl’s block structure and void formation during tensile loading....

Radiation modification and interaction mechanism of polypropylene and polyethylene by protons and electrons

International Nuclear Information System (INIS)

Wang Guanghou

1988-10-01

A systematic investigation of radiation effects on isotactic polypropylene (PP) and low-density polyethylene (PE) films by protons and electrons is reported. Electrons can make polyethylene cross-linked and polypropylene crached while protons can improve the PP mechanical properties and deteriorate polyethylene with increasing the irradiation dose. The structural analysis shows that conversion between α and β phases occurs and the crystallinity remains constant in the electron-irradiated polypropylene whereas the network structure is formed by allyl-type radicals in the e - -irradiated polyethylene. The infrared spectra indicate that conformational changes have taken place in the polypropylene under proton bombardment, such as the transition from an ordered to a disordered state in the crystalline region, the formation of double bonds as well as trans-conformations. This leads to the cross-linking between macromolecules of polypropylene at the proper irradiation doses, thus enhancing its mechanical properties. The cross-linking of polypropylene by proton bombardment observed and its properties may have some potential applications

Characterization and Some Properties of Functionalized Graft Copolymer

International Nuclear Information System (INIS)

Hegazy El-Sayed, A.; Kamal, H.; Mahmoud, Gh.A.; Khalifa, N.A.

2000-01-01

The study involved the investigation and characterization of membranes prepared by graft copolymerization of acrylonitrile (AN) and vinyl acetate (VAc) binary monomers onto low density polyethylene (LDPE) and isotactic polypropylene (IPP). The mutual gamma-irradiation method was used as a grafting technique. The effects of grafting and chemical treatments on the thermal properties and crystallinity of prepared graft copolymer have been investigated using DSC, TGA and XRD. IR spectra recorded before and after grafting and also for the chemically treated membranes to elucidate the structural changes occurred due to grafting and chemical treatments

Development of foams from linear polypropylene (PP) and high melt strength polypropylene (HMSPP) polymeric blends

International Nuclear Information System (INIS)

Cardoso, Elisabeth Carvalho Leite

2009-01-01

Foamed polymers are future materials, with a comprehensive application field. They can be used in order to improve appearance of insulation structures, for example, or to reduce costs involving materials. This work address to Isotactic Polypropylene / High Melt Strength Polypropylene blends, for foams production. Rheological behavior of polymer melt, especially referring to viscosity in processing temperature, plays a decisive role in applications where dominates extensional flow, as in case of foaming. If the viscosity is very low, it will correspond to a low melt strength, as in case of linear homopolymer (Isotact PP), and the foam will be prejudiced, due to the impossibility of expansion. Otherwise, if the viscosity is very high, with a high melt strength, the foam will collapse immediately after its formation. In order to get foams with an homogeneous and defined cellular structure, there were accomplished blends, 50% in weight, between linear homopolymer (isotactic PP) and HMSPP, from PP modified as per gamma radiation, in acetylene environment and at a 12.5 kGy doses. Extrusion process used a soluble foaming methodology, according to a processing/dissolution principle, which involves the dissolution of a Physical Blowing Agent (PBA), under 30 bar pressure, homogeneously mixed with polymeric melt. Extrusion conditions, that generally involve temperature, pressure and viscoelastic material flow control were experimentally investigated to define prevalent characteristics for producing foams. Nitrogen was the used PBA and process extrusion parameters were adapted to PP, HMSPP and their 50% in weight mixtures thereof. Major PP and HMSPP characteristics were obtained via melt Index and melt strength and thermal analyses (DSC/TGA), in order to make viable and to reproduce foaming as per extrusion process. Foams cellular morphology of PP, HMSPP and their 50% in weight mixtures thereof was investigated, with and without talc addition, as nucleating agent, by using

Morphology and crystalline-phase-dependent electrical insulating properties in tailored polypropylene for HVDC cables

Science.gov (United States)

Zha, Jun-Wei; Yan, Hong-Da; Li, Wei-Kang; Dang, Zhi-Min

2016-11-01

Polypropylene (PP) has become one promising material to potentially replace the cross-link polyethylene used for high voltage direct current cables. Besides the isotactic polypropylene, the block polypropylene (b-PP) and random polypropylene (r-PP) can be synthesized through the copolymerization of ethylene and propylene molecules. In this letter, the effect of morphology and crystalline phases on the insulating electrical properties of PP was investigated. It was found that the introduction of polyethylene monomer resulted in the formation of β and γ phases in b-PP and r-PP. The results from the characteristic trap energy levels indicated that the β and γ phases could induce deep electron traps which enable to capture the carriers. And the space charge accumulation was obviously suppressed. Besides, the decreased electrical conductivity was observed in b-PP and r-PP. It is attributed to the existence of deep traps which can effectively reduce the carrier mobility and density in materials.

Study of structural modifications in the stretched polypropylene (PP) film for various ratios

International Nuclear Information System (INIS)

Melinte, S.; Leanca, M.; Moise, M.; Mateescu, N.

1979-01-01

The initial spherolitic structure of isotactic polypropylene films changes as a result of their plastic deformation. The fibrous structure fraction increases with the draw ratio. Interfibrillar ranges, formed by molecules binding adjacent microfibrils, also develop. Along interfibrillar borders there occur voids which have a special role in lending properties to the film. Amorphous orientation rises proportionally to the draw degree while the crystal lattice orientation quickly grows and is almost completed for lambda = 5. (author)

Influence of shear flow on the specific volume and the crystalline morphology of isotactic polypropylene

NARCIS (Netherlands)

van der Beek, M.H.E.; Peters, G.W.M.; Meijer, H.E.H.

2006-01-01

The influence of shear flow on the temperature evolution of the specific volume and the crystalline morphology of two iPP's, differing in weight-averaged molar mass w, was investigated at nonisothermal conditions and elevated pressures, using a custom-designed dilatometer. These conditions are

A novel insight into the origin of toughness in polypropylene-calcium carbonate microcomposites: multivariate analysis of ss-NMR spectra

Czech Academy of Sciences Publication Activity Database

Kukačková, Olivia; Nguyen, Viet Dung; Abbrent, Sabina; Urbanová, Martina; Kotek, Jiří; Brus, Jiří

2017-01-01

Roč. 132, 6 December (2017), s. 106-113 ISSN 0032-3861 R&D Projects: GA ČR(CZ) GA16-04109S; GA MŠk(CZ) LO1507 Institutional support: RVO:61389013 Keywords : isotactic polypropylene microcomposites * CaCO3 * toughness Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer sci ence Impact factor: 3.684, year: 2016

Mechanical Properties of Non-Woven Polyester Fibers and Polymer-Modified Bitumen Composites

Directory of Open Access Journals (Sweden)

V. Hadadi

2007-12-01

Full Text Available Blown bitumen (110/10 was mixed with heavy vacuum slops (H.V.S, 60/70 penetration grade bitumen and recycled isotactic polypropylene (iPP at different levels. The resulting resins were used to impregnate non-woven poly(ethylene terephthalate fibers to form composites. The modulus and penetration grade of the resulting bituminous resins were determined. It was found that these bituminous resins drastically affect the modulus of the composites formed by low-Young’s modulus fibers such as polyesters. Consequently, interactions between resin and fibers and the correlation length of asphalthenes (in absence of iPP and interdiffused coalescence and segregated network of asphalthenes (in presence of iPP result in a non-linear behavior of composite’s modulus. The behavior of the composites with or without iPP is controlled by resin toughness and resin interactions with the fiber through the viscosity. Comparison of the experimental composite modulus data with the theoretical modulus data revealed that the Takayanangi’s model best predicts the behavior of these composites. The adjustment factors of this model were reported and proposed as an indication of fiber-resin interaction. It was also found that the modulus of fibers is affected by toughness, viscosity and the iPP content of the bituminous resin.

Mechanical Properties of Nanofilled Polypropylene Composites

Directory of Open Access Journals (Sweden)

Cristina-Elisabeta PELIN

2015-06-01

Full Text Available The paper presents a study concerning mechanical performance of thermoplastic nanocomposites based on isotactic polypropylene matrix, nanofilled with montmorillonite modified with quaternary ammonium salt and carboxyl functionalized carbon nanotubes, respectively, added in the same concentration relative to the matrix. The nanofilled and single polymer materials were obtained by simple melt compounding through extrusion process followed by injection molding into specific shape specimens for mechanical testing of the samples. Mechanical properties were evaluated by tensile and 3 point bending tests. In terms of modulus of elasticity, the results showed overall positive effects concerning the effect of nanofiller addition to the thermoplastic polymer. The fracture cross section of the tested specimens was characterized by FT-IR spectroscopy and SEM microscopy.

Partially-Functionalized Isotactic Polystyrene with Blocky Comonomer Segments

Science.gov (United States)

Siegel, Ariel; Powers, Wayne; Ryu, Chang Y.

2012-02-01

Isotactic polystyrenes (iPSs) have been functionalized in solution, while the accessibility of functionalizing agent is limited by the formation of crystalline domains at various temperatures. The chemical system used is the borylated isotactic polystyrene system, and we investigated the temperature effects on reaction kinetics to ultimately control the blockiness of borylated segments in the resulting copolymer. The chemical composition of partially borylated iPS reaches a steady state that is dependent on temperature. This synthesis has been performed at many different temperatures, with different steady states being reached at different temperatures. Further analysis by differential scanning calorimetry (DSC) has shown that the higher temperature reactions have greater effect on breaking down the crystal lattice structure of the isotactic polystyrene. As a result, the lower temperature reactions affect the crystalline structure less, and the resulting copolymer has more blockiness.

IPP annual report 1981

International Nuclear Information System (INIS)

1982-01-01

In part A of this annual report the tokamak and stellarator projects at the IPP are reported: ASDEX, ASDEX upgrade, JET collaboration, NET collaboration, Wendelstein VII-7, Wendelstein VII-AS, Wendelstein VII-X and stellarator reactor system studies. In part B the departments and research groups give a brief, but detailed report of the results in the field of research and development. In part C a review is presented of the IPP organisation. Part D includes the papers and conference reports published in 1981. Finally a brief description of the IPP projects at German universities is presented. (GG) [de

The influence of glass fibers on the morphology of β-nucleated isotactic polypropylene evaluated by differential scanning calorimetry

Directory of Open Access Journals (Sweden)

Janevski Aco

2015-01-01

Full Text Available The presence of fillers/fibers can significantly affect the polymorphic behavior of semi-crystalline polymers. The influence of glass fibers on morphology of β-nucleated iPP during isothermal and nonisothermal crystallization was analyzed in detail by DSC, and the kinetics and thermodynamic parameters were determined for the systems containing 10-60 % glass fibers. The presence of glass fibers in model composites with β-iPP has insignificant effect on the morphology of the polymer. Thermodynamic and kinetics parameters of crystallization of iPP in model composites are close to those obtained for the nucleated polymer. The relative content of β-crystalline phase is slightly affected by increasing glass fiber’s content from 10 % mas to 60 % mas, due to appearance of α-crystallites. However, the stability of β-crystalline phase is decreased by the increasing glass fibers content and there appeared certain amount of β1 and β2 phases which are known as disposed to recrystallization.

Ziegler-Natta catalysts for the preparation of polypropylene clay nanocomposites from magnesium ethoxide

International Nuclear Information System (INIS)

Marques, Maria de Fatima V.; Silva, Micheli G. da; Ferreira, Ana Luiza R.

2009-01-01

In the present work, the process for the preparation of Ziegler-Natta catalysts based on MgCl 2 /TiCl 4 was evaluated on the synthesis of isotactic polypropylene. The catalysts were produced by the chemical activation process aiming the morphology control, in order to obtain catalyst particles with spherical form. The synthesis of the catalytic support was accomplished from magnesium ethoxide at different preparation conditions. Commercial clays were also added in the preparation of ZN catalysts, which were employed in propylene polymerization. The purpose was to synthesizing polypropylene nanocomposites by in situ polymerization technique. The results indicated that the developed methods of catalyst preparation were effective, since they have shown high activities and they produced PP with high melting temperatures. It was possible to verify by XRD that the catalytic components were inserted in the clays galleries and the polymers obtained by means of those catalysts are possibly exfoliated nanocomposites. (author)

The effect of specific beta-nucleation on morphology and mechanical behavior of isotactic polypropylene

Czech Academy of Sciences Publication Activity Database

Kotek, Jiří; Raab, Miroslav; Baldrian, Josef; Grellmann, W.

2002-01-01

Roč. 85, č. 6 (2002), s. 1174-1184 ISSN 0021-8995 R&D Projects: GA ČR GA106/99/P011; GA ČR GA106/98/0718; GA AV ČR IAA4050904 Institutional research plan: CEZ:AV0Z4050913 Keywords : polypropylene * morphology * beta-nucleation Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.927, year: 2002

Isotactic polypropylene/carbon nanotube composites prepared by latex technology. Thermal analysis of carbon nanotube-induced nucleation

NARCIS (Netherlands)

Miltner, H.E.; Grossiord, N.; Lu, K.; Loos, J.; Koning, C.E.; Van Mele, B.

2008-01-01

During nonisothermal crystallization of highly dispersed polypropylene/carbon nanotube (CNT) composites, considerable heterogeneous nucleation is observed to an extent scaling with the CNT surface area. Saturation occurs at higher loadings, reaching a plateau value for the crystallization onset

IPP annual report 1984

International Nuclear Information System (INIS)

1984-01-01

The scientific activities of IPP comprise two programmes, Tokamaks and Stellarators, the main results of which are summarized in two overviews introducing the corresponding sections in the body of the report. The scientific work is firmly integrated into a network of cooperation. In Germany, we collaborate with Kernforschungszentrum Karlsruhe in the 'Entwicklungsgemeinschaft Kernfusion'; of the collaboration with universities the most successful has been that with Stuttgart on ECRH. The IPP programme forms an integral part of the European fusion programme. (orig./GG)

Study on the formation of the nanogel and microgels polypropylene modified by gamma radiation and incorporation of silver nanoparticles to biocides activity

International Nuclear Information System (INIS)

Oliani, Washington Luiz

2013-01-01

The study consists of the synthesis of HMSPP (polypropylene with high melt strength), also called polypropylene modified by gamma irradiation from iPP (isotactic polypropylene) in presence of acetylene at 110 kPa pressure and irradiated with γ of 60 Co source at doses of 5, 12.5 and 20 kGy. The gel fraction of the samples was determined by extracting in xylene. The soluble portion of the samples was decanted to deposition on glass substrate until complete volatilization of xylene at room temperature of 25 °C. On the soluble portion of 12.5 kGy irradiated sample were added silver nanoparticles (AgNPs) in proportions of 0.25, 0.5, 1.0, 2.0 and 4.0 wt%. These gel samples were characterized by: scanning electron microscopy/energy dispersive spectroscopy (SEM / EDS), infrared spectroscopy (FTIR), scanning electron microscopy with field emission (FE-SEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), reduction of colony forming unit (CFU) (%) and cytotoxicity assay. In this study of the morphology, it has been observed the formation of microgels in polypropylene increasing with the dose PP 5 kGy < PP 12.5 kGy < 20 kGy. Nanoscale structures of gels polypropylene (nanogels and nanofibers) were found in samples of PP 12.5 kGy and 20 kGy. The nanogels are formation of crosslinking, branching and entanglement that are nucleated in regions of high energy concentration (spurs) of one irradiated sample. Efficiency in tests of bactericide activity of the gels with AgNPs was observed versus E. coli and S. aureus from 1% AgNPs and non cytotoxicity were characterized in those samples for mammalian cells. In a second stage of this work films of the blend of PP and modified PP (50/50) were produced in a twin screw extruder. AgNPs were added to the extrusion processing in proportions of 0.1; 0.25; 0.5; 1.0; 1.0 PVP; 2.0 and 4.0 wt%. The films obtained were characterized by differential scanning calorimetry (DSC), thermogravimetry

Polypropylene film with silver nanoparticles and nanoclay aiming to action biocidal

International Nuclear Information System (INIS)

Oliani, W.L.; Lima, L.F.C.P.; Lugao, A.B.; Parra, D.F.; Fermino, D.M.; Diaz, F.R.V.

2014-01-01

This paper presents an initial study of films made of polypropylene nanoclay and silver nanoparticles. The nanocomposite of polypropylene (iPP), commercial organoclay - montmorillonite (MMT), Cloisite 20A at concentrations of 1.0% and silver nanoparticles (AgNPs) at a concentration of 0.1% were prepared in a twin-screw-extruder, using polypropylene with maleic anhydride (PP-g-MA) as coupling agent. The properties of nanocomposites of PP/MMT/AgNPs are closely related to the dispersion of silver particles and the distribution of sheets of MMT in the polymer matrix, which define its efficiency in the case of the particles and their interaction clay/polymer matrix. However, this combination of MMT and AgNPs that are polar, with the polymer matrix nonpolar in the molten state, presents a challenge. The characterization of the film was performed by analysis of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and reduction of colony forming unit (CFU %). The results indicate the formation of predominantly exfoliated microstructures and agglomeration of silver nanoparticles in the film. The effect of silver nanoparticles was evaluated against bacteria E.coli and S.aureus. (author)

An Interface Transformation Strategy for AF-IPPS

Science.gov (United States)

2012-12-01

Oracle, or SAP . Like other AF and Department of Defense (DoD) ERP programs, AF-IPPS is expected to have 100+ interfaces with 90+ external trading partners...platform such as PeopleSoft, Oracle, or SAP . Like other AF and Department of Defense (DoD) ERP programs, AF-IPPS is expected to have 100...currently perform these functions. The core of AF-IPPS will be implemented using an Enterprise Resource Planning ( ERP ) platform such as PeopleSoft

Economic evaluation on participation of IPP as seen from an electric power system; Denryoku system kara mita IPP sannyu no keizaiteki hyoka

Energy Technology Data Exchange (ETDEWEB)

Kato, F.; Horibe, H.; Hayakawa, M.; Suzuki, Y.; Kaji, Y. [Nagoya University, Nagoya (Japan)

1997-01-30

A discussion was given on value of participation of an IPP as seen from an electric power system operation plan prepared by utilities. In the discussion, evaluation was made using as the breakeven cost of IPP power purchase prices the difference in power generation cost between electric power systems in which an IPP is participating and not participating, or in other words, the reduced portion of the power generation cost. As a result of the discussion, the following matters were indicated: in the case where an utility company expands its capacity by installing a coal-fired thermal power plant which is lower in operation cost, to deal with increase in power demand, the breakeven cost could be an avoidable cost for the utility company; if the expansion by installing a coal-fired thermal plant is not possible, the breakeven cost for a base type IPP would rise; the breakeven cost for a peak type IPP would be higher than for the base type IPP because the breakeven cost can serve to cut the peak for generators owned by the utility company; and participation of an IPP to power sources in remote areas would provide a large effect to reduce power transmission loss in an entire system, thereby increasing the breakeven cost. 1 ref., 9 figs., 3 tabs.

Some radiation aspects of irradiated polyethylene and polypropylene

International Nuclear Information System (INIS)

Gvozdic, N.V.

1978-01-01

Unfractionated PE (Marlex-6002, ECPE, HPE) and fractionated PE (MWD approximately 3.7) were used for the study of ionizing radiation effects such as vinyl decay in relation to the degree of crystallinity, as well as crosslinking, G(alkyl), and free radical decay. Isotactic PP was used for the study of alkyl radical decay. It was found that the rate of vinyl decay in PE is dependent on the degree of crystallinity only if free radicals were not annealed out subsequent to irradiation and before measurements. Both annealed and quenched samples have shown the same rate of vinyl decay if free radicals were annealed out. The study of crosslink formation in relation to the degree of crystallinity has disclosed that the higher gel fraction is always obtained in the highly amorphous samples, rather than in the highly crystalline ones. The study of G(alkyl) for irradiated PE, has disclosed that a higher G(alkyl) value is in the amorphous than in the crystalline regions. This result indirectly supports the conclusion that gel is formed preferably in the quenched than in the annealed samples. The higher G(alkyl) in i-PP than in PE was expected on the basis of the more effective Frank-Rabinowitch caging effect in PE. Evidence has been obtained for the production of two kinds of alkyl radicals in i-PP at LNT. That is, alkyl radical species of 4- and 8-line ESR spectra. A new transformation temperature of alkyl radical spectra (approximately 313 0 K) was discovered. The study of decay of alkyl radical (8-line) species has revealed that neither simple first nor second order rate laws were obeyed, above or below Tg. The H 2 catalytic effect on alkyl (8-line) species was discovered at the temperature above Tg but not below Tg

IPP: Annual report 1982

International Nuclear Information System (INIS)

1982-01-01

This report presents a detailed outline of the work accomplished within the framework of the Tokamak projects ASDEX and ASDEX Upgrade and the JET and NET projects, the stellarator projects VIII-A, VII-AS and VII-X, and of stellarator reactor system studies. The various scientific research departments, such as Experimental Plasma Physics 1, 2 and 3, Theoretical Plasma Physics 1 and 2, Plasma-Wall. Interactions, and Information Sciences give an account of the results of their research and development work. Further reports on the 1982 activities deal with a) the organisational structure of the IPP, b) administrative and business items, c) scientific publications and conference proceedings, and with d) IPP-supported projects at universities. (GG) [de

IPP fuel contracts - creating certain contracts for uncertain times

Energy Technology Data Exchange (ETDEWEB)

Coddington, I. [Coddington International Pty. Ltd., Milsons Point, NSW (Australia)

1998-12-31

Coal contracts for the new Asian Independent Power Producers (IPPs) are examined. Since most IPPs will be selling to state electricity utilities, often in competition with power plant using other fuels, coal based IPPs must negotiate advantageous coal supply contracts several years before the commissioning of a plant, and must ensure security of supply for at least the life of the construction loan. A more recent trend in the developed world is the Merchant IPP, where there is no guaranteed electricity sale. Lenders are wary of IPPs relying an imported coal, and insist on binding fuel contracts, while coal companies are wary of the quantity of information demanded by these lenders. A full understanding of the risks involved is needed; and a method of price indexation for the contracts. Contracts must also specify security of supply, coal quality, freight contracts and other details. 2 figs.

Integrated analysis of isopentenyl pyrophosphate (IPP) toxicity in isoprenoid-producing Escherichia coli

DEFF Research Database (Denmark)

George, Kevin W; Thompson, Mitchell; Kim, Joonhoon

2018-01-01

evidence that IPP can be transported by E. coli, findings that might be broadly relevant for the study of isoprenoid biosynthesis. Finally, we discover that IPP accumulation leads to the formation of ApppI, a nucleotide analog of IPP that may contribute to observed toxicity phenotypes. This comprehensive...... assessment of IPP stress suggests potential strategies for the alleviation of prenyl diphosphate toxicity and highlights possible engineering targets for improved IPP flux and high titer isoprenoid production....

Comparative Investigation of Mechanical–Physical Characteristics of Biodegradable and Non-Degradable Yarns

Directory of Open Access Journals (Sweden)

Krikštanavičienė Kira

2014-06-01

Full Text Available This article presents the results from investigations of tensile tests, absorbency test and degradation test of biodegradable and non- or partly biodegradable yarns produced from pure poly hydroxybutyrate-co-valerate (PHBV, poly (lactide acid (PLA, isotactic polypropylene (iPP polymers and their blends. The results indicate that mechanical-physical properties of PHBV are improved by adding PLA and iPP to PHBV. The main results indicate that the PHBV/PLA and PHBV/iPP (70/30 blends had better mechanical properties than pure PHBV, as well as improved immiscibility and the same or lower degradation in sodium chloride solution, respectively. The PHBV/PLA and PHBV/iPP blends showed a tendency for lower crystallinity and stiffness of the yarns, rendering them less stiff and fragile. The absorption tests showed that absorption dynamic process depends on the structure and raw materials of the yarns. The disinfectant in all samples is absorbed faster than blood. Research results showed that pure PHBV yarns have good hydrophobic properties, compared with pure PLA and iPP yarns. The use of additional PLA and iPP polymers changed the wetting behaviour of yarns. Absorption time of blended yarns in disinfectant liquid decreases and absorption time in the case of blood significantly increases in comparison with PLA and iPP yarns and decreases compared with PHBV yarns. The degradation tests (within 90 days in a solution of sodium chloride showed that pure PHBV and PHBV/PLA blends degraded at different rates but with the loss of the same weight, while pure PHBV and PHBV/iPP blends degraded at the same rate, but PHBV/iPP blends had worse destruction results. Such improvements are expected to be important for the practical application of PHBV in some fields

Influence of Magnetite Nanoparticles on the Dielectric Properties of Metal Oxide/Polymer Nanocomposites Based on Polypropylene

Science.gov (United States)

Maharramov, A. A.; Ramazanov, M. A.; Di Palma, Luca; Shirinova, H. A.; Hajiyeva, F. V.

2018-01-01

Structure and dielectric properties of polymer nanocomposites based on isotactic polypropylene and iron oxide (Fe3O4) nanoparticles are studied. Distribution of magnetite nanoparticles in a polymer matrix was studied by scanning electron microscopy (SEM, Carl Zeiss). Dielectric properties of nanocomposites were examined by means of E7-21 impedance spectrometer in the frequency range of 102-106 Hz and temperature interval of 298-433 K. The frequency and temperature dependences of the dielectric permittivity ɛ, as well as the temperature dependence of log (ρ) were constructed. It is shown that introduction of the magnetite (Fe3O4) nanoparticles into a polypropylene matrix increases the dielectric permittivity of nanocomposites. An increase in the dielectric permittivity is explained by the increase in the polarization ability of nanocomposites. It is found that a decrease in the specific resistance with increasing temperature up to 318 K is associated with an increase in the ionic conductivity of nanocomposites. An increase in the resistance at temperatures higher than 358 K is due to the destruction of the crystalline phase of the polymer, as a result of which the distance between the Fe3O4 nanoparticles increases.

Fuel strategies for natural gas fired cogeneration and IPP projects

International Nuclear Information System (INIS)

Gottlieb, J.W.

1992-01-01

This paper as published is the outline of a presentation on managing the risk of varying fuel costs as part of a successful fuel strategy for natural gas fired cogeneration and Independent Power Producer (IPP) projects. So long as the fuel cost that electric utilities recover from their ratepayers differs from the fuel costs incurred by IPP and Qualifying Facility (QF) plant operators, the largest variable cost risk of any QF or IPP will continue to be the cost of fuel. Managing that risk is the mission of any successful fuel procurement strategy. Unfortunately, a quick review of the last 20 years in the oil and gas industry reveals dramatic and substantial changes in price and fuel availability that few, if any, industry experts could have predicted in 1971. Recognizing that the fuel cost risk to a QF or IPP investor also spans a 20 year period, the typical term of a QF or IPP power purchase contract, a successful fuel procurement strategy must consider and address the likelihood of future changes. Due to federal and state regulatory changes made from 1978 to 1989, the current structure of the oil and gas industry appears to provide end-users with the tools to improve the manageability of fuel cost risks. QF and IPP developers can choose the type of service they desire and can negotiate most of the contractual elements of that service. Until electric utilities are allowed to flow through their rates the fuel costs incurred by QFs and IPPs, a thorough analysis of the available fuel procurement options prior to development of a QF or IPP will continue to be absolutely necessary

B.C. energy plan implementation : IPP perspective

International Nuclear Information System (INIS)

Davis, S.

2003-01-01

British Columbia's new electricity policy was discussed with particular reference to the fundamentals of market structure and transmission access. The policy calls for low cost electricity and public ownership, secure reliable supply, increased private sector opportunities, and environmental responsibility. This paper described the impact of the energy policy on independent power producers (IPP), and the key issues they will face in reregulation. Current and proposed power procurement programs and IPP projects opportunities were also described along with the major risks to IPP development. The small run of river hydro projects include: the Hystad Creek 2 MW project; the Pingston 30 MW project, and the Brandywine 7 MW project. Other green IPP projects include the Delta Landfill Gas Cogen 5 MW project, the Palmerston/Mt. Brandes 50 MW wind project, and the Meagher Creek geothermal project. It was noted that the major risks vary by phase. It was suggested that open access to transmission wires should be improved and a more competitive wholesale generation market should be established. In January 2003, the government of British Columbia announced new coal-fired boiler emission standards. A new Environmental Assessment Act was also announced along with the proposed phase out of the Burrard Thermal Power Generating Station. 13 figs

Crystalline structure of polypropylene in blends with thermoplastic elastomers after electron beam irradiation

International Nuclear Information System (INIS)

Steller, Ryszard; Zuchowska, Danuta; Meissner, Wanda; Paukszta, Dominik; Garbarczyk, Jozef

2006-01-01

Isotactic polypropylene (PP) was blended in extruder with 0-50% addition of styrene-ethylene/butylene-styrene (SEBS) and styrene-butadiene-styrene (SBS) block copolymers. Granulated blends were irradiated with electron beam (60 kGy) and 1 week later processed with injection molding machine. Properties of samples molded from irradiated and non-irradiated granulates were investigated using DSC, WAXS, MFR, SEM and mechanical and solubility tests. It was found that the SEBS based systems are more resistant to irradiation in comparison to similar blends with SBS copolymer. Such behavior can be explained by the presence of double bonds in elastic SBS block. Irradiation of PP-SBS blends leads to considerable structure changes of crystalline and amorphous PP phases and elastic SBS phase. It indicates creation of new (inter)phase consisting of products of grafting and cross-linking reactions. Irradiated PP-SBS blends show significant improvement of impact strength at low temperatures

Assessment of Barriers to Providing Introductory Pharmacy Practice Experiences (IPPEs in the Hospital Setting

Directory of Open Access Journals (Sweden)

Matthew J Gibson

2016-07-01

Full Text Available Objectives: The primary objective of the study is to identify the barriers to providing Introductory Pharmacy Practice Experiences (IPPEs in the hospital setting. Methods: Potential barriers to IPPEs were identified via literature review and interviews with current IPPE preceptors from various institutions. Based on this information, an electronic survey was developed and distributed to IPPE preceptors in order to assess student, preceptor, logistical and college or school of pharmacy related barriers that potentially exist for providing IPPE in the hospital setting. Results: Sixty-eight of the 287 eligible survey respondents (24% completed the electronic survey. Seventy-six percent of respondents agreed or strongly agreed that available time was a barrier to precepting IPPE students even though a majority of respondents reported spending a third or more of their day with an IPPE student when on rotation. Seventy-three percent of respondents disagreed or strongly disagreed that all preceptors have consistent performance expectations for students, while just 46% agreed or strongly agreed that they had adequate training to precept IPPEs. Sixty-five percent of respondents agreed that IPPE students have the ability to be a participant in patient care and 70% of preceptors believe that IPPE students should be involved in patient care. Conclusions: Conducting IPPEs in the institutional setting comes with challenges. Based on the results of this study, experiential directors and colleges/schools of pharmacy could make a positive impact on the quality and consistency of IPPEs by setting student expectations and training preceptors on appropriate and consistent expectations for students.   Type: Original Research

O and M outsourcing saving costs for IPPs

International Nuclear Information System (INIS)

Byerly, K.; Mason, J.

1997-01-01

Over the past decade, many countries have opened their markets to independent power producers (IPPs) and expansion of utility projects. With these new found opportunities, IPPs and utilities must focus on their core business as power generators, while obtaining the most cost-effective operations and maintenance (O and M) services. Many have found that third-part O and M outsourcing is the most cost-effective and profitable way to go. (Author)

Effect of Isotacticity of Linear Poly(N-isopropylacrylamide) on its ...

Indian Academy of Sciences (India)

decreased with the increase in the isotacticity of the polymer. Gelation ... microscopy (SEM), differential scanning calorimetry ... The gap between two paral- ... sidering degree of polymerization, x = 6) with benzyl ..... Apart from the blue shift, the absorbance value grad- ..... for Bethe lattice, n should have the value equal to.

IPPs in Sub-Saharan Africa: Determinants of success

International Nuclear Information System (INIS)

Eberhard, Anton; Gratwick, Katharine Nawaal

2011-01-01

This study analyses the outcomes of independent power projects (IPPs) across Sub-Saharan Africa. Approximately 20 such projects have taken root to date, concentrated mainly in 8 countries. A suite of country level and project level factors play a critical role in determining project success, chief among them: the manner in which planning, procurement and contracting are coherently linked, the role of development finance institutions along with the development origins of firms and credit enhancements. - Highlights: → We analyse the outcomes of independent power projects (IPPs) across Sub-Saharan Africa. → Approximately 20 IPPs have taken root to date, concentrated mainly in 8 countries. → A suite of country level and project level factors play a critical role in determining project success. → Key success factors are the coherence of planning, procurement and contracting. → Also important is the role of DFIs, the development origins of firms, and credit enhancements.

Intra-vesical Prostatic Protrusion (IPP) Can Be Reduced by Prostatic Artery Embolization

Energy Technology Data Exchange (ETDEWEB)

Lin, Yen-Ting, E-mail: ymerically@gmail.com; Amouyal, Grégory, E-mail: gregamouyal@hotmail.com [Assistance Publique Hôpitaux de Paris, Hôpital Européen Georges-Pompidou, Vascular and Oncological Interventional Radiology (France); Thiounn, Nicolas, E-mail: nicolas.thiounn@egp.aphp.fr [Assistance Publique Hopitaux de Paris, Hôpital Européen Georges-Pompidou, Urology (France); Pellerin, Olivier, E-mail: olivier.pellerin@aphp.fr [Université Paris Descartes, Sorbonne Paris-Cité (France); Pereira, Héléna, E-mail: helena.pereira@aphp.fr; Giudice, Costantino Del, E-mail: costantino.del-giudice@egp.aphp.fr; Déan, Carole, E-mail: carole.dean@aphp.fr [Assistance Publique Hôpitaux de Paris, Hôpital Européen Georges-Pompidou, Vascular and Oncological Interventional Radiology (France); Sapoval, Marc, E-mail: marc.sapoval2@aphp.fr [Université Paris Descartes, Sorbonne Paris-Cité (France)

2016-05-15

BackgroundProstate artery embolization (PAE) is a new approach to improve lower urinary tract symptoms (LUTS) related to benign prostatic hyperplasia. PAE results in global reduction of prostate volume (PV). There are no data available on the efficacy of PAE in reducing intra-vesical prostatic protrusion (IPP), an anatomic feature that is clinically related with bladder outlet obstruction and LUTS.ObjectiveTo assess the results of PAE in patients with significant IPP due to median lobe hyperplasia and to compare the IPSS decrease and IPP change.Material and MethodsProspective analysis of 18 consecutive patients with significant IPP (>5 mm) related to median lobe hyperplasia undergoing PAE using 30–500-μm-calibrated trisacryl microspheres. We measured IPP on sagittal T2-weighted images before and 3 months after PAE. IPSS and clinical results were also evaluated at 3 months.ResultsPAE resulted in significant IPP reduction (1.57 cm ± 0.55 before PAE and 1.30 cm ± 0.46 after PAE, p = 0.0005) (Fig. 1) with no complication. IPSS, quality of life (QoL), total prostate-specific antigen (PSA) level, and PV showed significant reduction after PAE, and maximum urinary flow rate (Q{sub max}) showed significant increase after PAE. No significant change of International Index of Erectile Function (IIEF) for clinical evaluation after PAE. A significant correlation was found between the IPP change and the IPSS change (r = 0.636, p = 0.0045).ConclusionPatients had significant IPP reduction as well as significant symptomatic improvement after PAE, and these improvements were positively correlated.

Enthalpy relaxation in the cooling/heating cycles of polypropylene/organosilica nanocomposites

International Nuclear Information System (INIS)

Privalko, V.P.; Dinzhos, R.V.; Privalko, E.G.

2005-01-01

Non-isothermally crystallized samples of the neat isotactic polypropylene homopolymer (PP-0) and of a series of nanocomposites (PNC) containing up to 4.68 vol.% of organosilica were characterized by wide-angle and small-angle X-ray diffraction and by the standard DSC, while their melting behavior was studied in the temperature-modulated DSC mode at three underlying heating rates and five modulation frequencies. It was established that the lamellar morphology of PP remained essentially unchanged, whatever the previous cooling rate and/or the organoclay content. The patterns of melting endotherms in both the neat PP sample and the PNC could be semi-quantitatively characterized by a simple Debye model with a single, temperature- and underlying heating rate-dependent characteristic time. The mechanisms of structural rearrangements in the melting intervals of the neat PP sample and the PNC were basically similar; however, the spatial scale of such rearrangements in the latter samples was significantly reduced due to severe steric constraints on the PP chain mobility in the melt state from the infinite cluster of nanoparticles

Radioluminescence of aromatic molecule solutions in atactic and isotactic polystyrene

International Nuclear Information System (INIS)

Lisovskaya, I.A.; Alfimov, M.V.; Milinchuk, V.K.; Skvortsov, V.G.

1975-01-01

The generation of excited states of naphthalene-d 8 and carbazole molecules in polystyrene (PS) under X-ray illumination was investigated using luminescence method. A comparison of the concentration dependences of radioluminescence of the aromatic additives to solid PS and to toluene as well as the pattern of concentration versus photoluminescence of naphthalene-d 8 in PS demonstrates that unlike toluene there is no singlet-triplet conversion in PS owing to the formation of excimers. It is shown that the excited ststes of the aromatic additives in PS are populated under radiolysis via an energy transfer from singlet to triplet molecules of the matrix. Under the radiolysis the excited states of PS molecules may generate upon charge recombination. A comparison of radio luminescence spectra of the corresponding aromatic additives in two isomeric PS structures (atacting and isotactic) shows different processes with charge participation. The difference detected in the radioluminescence spectra of aromatic additives in the atactic and isotactic PS explained by the greater number of defects in atactic PS competing with the polymer molecule ion for charge capture

IPP partnerships : forging Canada's wind industry

International Nuclear Information System (INIS)

Magee, J.T.

2006-01-01

Following the request for proposal (RFP)-fueled explosion in renewable energy source development over the past 3 years, independent power producer (IPP) financial expertise has become critical to successful project implementation. This presentation reviewed aspects of Canadian wind market related to independent power producer (IPP) investment activity. A map of major Canadian wind farms operational at the end of 2005 was provided, as well as a map of provinces with utility RFP activity. Planned projects were listed by MW. Recent provincial RFP winners were listed. It was suggested that project execution experience and financial security were highly valued in the recent Hydro-Quebec and Ontario RFP solicitations. Developer consolidation and scaling is likely to continue as large wind IPPs are in the best position to maximize efficiency gains in project economics. Financial strength will continue to be key to winning provincial wind RFPs, and Quebec and Ontario RFPs are likely to be dominated by players with balance sheet security. Smaller developers are losing their competitive position in RFP negotiations as more national and international energy giants move into the wind industry. The consolidation trend is ramping up quickly, and may be closing the window in which international investors can find acquisition targets with experience and viable projects. It was concluded that while small developers with robust projects still exist, they are being acquired at a rapid rate. refs., tabs., figs

IPP Max Planck Institute of Plasma of Physics at Garching

International Nuclear Information System (INIS)

1979-01-01

The cost accounting system of the IPP Max Planck Institute of Plasma Physics at Garching is described with all details as there are cost class accounting, cost centers, cost units and resulting overall cost summary. Detailed instructions are given about the implementation of this cost accounting system into the organisational structure of the IPP. (A.N.)

Impacts of IPP's, restructuring of QF's and expected impacts of PUHCA reform

International Nuclear Information System (INIS)

MacDonald, A.

1991-01-01

Under the Public Utility Holding Company Act, or PUHCA, the SEC regulates the capital structure of registered holding company systems and securities sales, mergers, service company arrangements, affiliate contracts, and other transactions involving registered holding companies and their subsidiaries. The SEC does not have ratemaking authority or otherwise regulate the operational aspects of the public utility business. Unlike QF's, which are exempt from PUHCA by virtue of the Public Utility Regulatory Policies Act of 1978, or PURPA, IPP's fall within the definition of an 'electric utility company,' and the owners of an IPP (i.e., its stockholders or partners) must carefully navigate the PUCHA mine field to avoid subjecting themselves to the registration requirements of PUHCA. Bills now pending in Congress would, if enacted, exempt some IPP's from PUHCA. In the meantime, PUHCA has not proven to be a complete bar to successful IPP development, although it has undoubtedly contributed to the creation of unusual ownership structures. This paper looks at the various approaches taken by IPP developers to solve the PUHCA problem. It focuses primarily upon structures in which certain equity investors acquire and hold non-voting securities, such as limited partnership interests or non-voting common stock, the role of individuals in the ownership of IPP's, and the use of one or more of the exemptions available under PUHCA for certain kinds of classes of 'holding companies.'

Study on the formation of the nanogel and microgels polypropylene modified by gamma radiation and incorporation of silver nanoparticles to biocides activity; Estudo da formacao de nanogeis e microgeis de polipropileno modificado por radiacao gama e incorporacao de nanoparticulas de prata visando a acao biocida

Energy Technology Data Exchange (ETDEWEB)

Oliani, Washington Luiz

2013-07-01

The study consists of the synthesis of HMSPP (polypropylene with high melt strength), also called polypropylene modified by gamma irradiation from iPP (isotactic polypropylene) in presence of acetylene at 110 kPa pressure and irradiated with γ of {sup 60}Co source at doses of 5, 12.5 and 20 kGy. The gel fraction of the samples was determined by extracting in xylene. The soluble portion of the samples was decanted to deposition on glass substrate until complete volatilization of xylene at room temperature of 25 °C. On the soluble portion of 12.5 kGy irradiated sample were added silver nanoparticles (AgNPs) in proportions of 0.25, 0.5, 1.0, 2.0 and 4.0 wt%. These gel samples were characterized by: scanning electron microscopy/energy dispersive spectroscopy (SEM / EDS), infrared spectroscopy (FTIR), scanning electron microscopy with field emission (FE-SEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), reduction of colony forming unit (CFU) (%) and cytotoxicity assay. In this study of the morphology, it has been observed the formation of microgels in polypropylene increasing with the dose PP 5 kGy < PP 12.5 kGy < 20 kGy. Nanoscale structures of gels polypropylene (nanogels and nanofibers) were found in samples of PP 12.5 kGy and 20 kGy. The nanogels are formation of crosslinking, branching and entanglement that are nucleated in regions of high energy concentration (spurs) of one irradiated sample. Efficiency in tests of bactericide activity of the gels with AgNPs was observed versus E. coli and S. aureus from 1% AgNPs and non cytotoxicity were characterized in those samples for mammalian cells. In a second stage of this work films of the blend of PP and modified PP (50/50) were produced in a twin screw extruder. AgNPs were added to the extrusion processing in proportions of 0.1; 0.25; 0.5; 1.0; 1.0 PVP; 2.0 and 4.0 wt%. The films obtained were characterized by differential scanning calorimetry (DSC

Evaluation of the value of availability and dispatchability in IPP contracts

International Nuclear Information System (INIS)

Camporeale, R.J.

1990-01-01

Consolidated Edison's resource plan relies on power from Independent Power Producers (IPPs) for a portion of future generation requirements. The additional restriction of obtaining this capacity through a bidding process requires the utility to evaluate a large number of potential contracts with different combinations of price, availability, and dispatchability. This paper discusses the theoretical considerations and outlines the methodology adopted for Consolidated Edison's first request for proposal. The value of an IPP contract is a function of the variable energy cost compared to the system avoided costs. For example, there is a value for availability only in those hours when contract cost is below the avoided cost and there is a penalty for non-dispatchability only in those hours when the contract cost is higher than the avoided cost. The best method to determine the value of an IPP contract would be to simulate the operation of the system with and without the IPP purchase using a perfect production cost model. In reality no model is perfect and there are trade-offs because not all aspects of system operation are captured. Performing a detailed production cost simulation for every proposal would be burdensome. Therefore, it was decided that a simplified methodology was needed. An additional benefit of a simplified approach is that the IPPs could score their own proposals and use this value as input into their final pricing scheme. The method developed relies on detailed production cost simulations to generate hourly avoided costs. A comparison of these avoided costs to the IPP variable costs becomes the basis for the calculation of the value of availability or dispatchability. This methodology can be applied consistently to all supply side resources; baseload or peaking, gas, oil or coal fired. This allows for the evaluation of all bid proposals on an equal basis

Supercritical CO2 foaming of radiation crosslinked polypropylene/high-density polyethylene blend: Cell structure and tensile property

Science.gov (United States)

Yang, Chenguang; Xing, Zhe; Zhang, Mingxing; Zhao, Quan; Wang, Mouhua; Wu, Guozhong

2017-12-01

A blend of isotactic polypropylene (PP) with high-density polyethylene (HDPE) in different PP/HDPE ratios was irradiated by γ-ray to induce cross-linking and then foamed using supercritical carbon dioxide (scCO2) as a blowing agent. Radiation effect on the melting point and crystallinity were analyzed in detail. The average cell diameter and cell density were compared for PP/HDPE foams prepared under different conditions. The optimum absorbed dose for the scCO2 foaming of PP/HDPE in terms of foaming ability and cell structure was 20 kGy. Tensile measurements showed that the elongation at break and tensile strength at break of the crosslinked PP/HDPE foams were higher than the non-crosslinked ones. Of particular interest was the increase in the foaming temperature window from 4 ℃ for pristine PP to 8-12 ℃ for the radiation crosslinked PP/HDPE blends. This implies much easier handling of scCO2 foaming of crosslinked PP with the addition of HDPE.

Polypropylene film with silver nanoparticles and nanoclay aiming to action biocidal; Filme de polipropileno com nanoargila e nanoparticulas de prata visando a acao biocida

Energy Technology Data Exchange (ETDEWEB)

Oliani, W.L.; Lima, L.F.C.P.; Lugao, A.B.; Parra, D.F., E-mail: washoliani@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Fermino, D.M.; Diaz, F.R.V. [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Departamento de Engenharia Metalurgica e de Materiais; Santos, P.M. dos [Universidade de Sao Paulo (USP), SP (Brazil)

2014-07-01

This paper presents an initial study of films made of polypropylene nanoclay and silver nanoparticles. The nanocomposite of polypropylene (iPP), commercial organoclay - montmorillonite (MMT), Cloisite 20A at concentrations of 1.0% and silver nanoparticles (AgNPs) at a concentration of 0.1% were prepared in a twin-screw-extruder, using polypropylene with maleic anhydride (PP-g-MA) as coupling agent. The properties of nanocomposites of PP/MMT/AgNPs are closely related to the dispersion of silver particles and the distribution of sheets of MMT in the polymer matrix, which define its efficiency in the case of the particles and their interaction clay/polymer matrix. However, this combination of MMT and AgNPs that are polar, with the polymer matrix nonpolar in the molten state, presents a challenge. The characterization of the film was performed by analysis of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and reduction of colony forming unit (CFU %). The results indicate the formation of predominantly exfoliated microstructures and agglomeration of silver nanoparticles in the film. The effect of silver nanoparticles was evaluated against bacteria E.coli and S.aureus. (author)

RF Negative Ion Source Development at IPP Garching

International Nuclear Information System (INIS)

Kraus, W.; McNeely, P.; Berger, M.; Christ-Koch, S.; Falter, H. D.; Fantz, U.; Franzen, P.; Froeschle, M.; Heinemann, B.; Leyer, S.; Riedl, R.; Speth, E.; Wuenderlich, D.

2007-01-01

IPP Garching is heavily involved in the development of an ion source for Neutral Beam Heating of the ITER Tokamak. RF driven ion sources have been successfully developed and are in operation on the ASDEX-Upgrade Tokamak for positive ion based NBH by the NB Heating group at IPP Garching. Building on this experience a RF driven H- ion source has been under development at IPP Garching as an alternative to the ITER reference design ion source. The number of test beds devoted to source development for ITER has increased from one (BATMAN) by the addition of two test beds (MANITU, RADI). This paper contains descriptions of the three test beds. Results on diagnostic development using laser photodetachment and cavity ringdown spectroscopy are given for BATMAN. The latest results for long pulse development on MANITU are presented including the to date longest pulse (600 s). As well, details of source modifications necessitated for pulses in excess of 100 s are given. The newest test bed RADI is still being commissioned and only technical details of the test bed are included in this paper. The final topic of the paper is an investigation into the effects of biasing the plasma grid

Emerging Market Attractiveness Index for hydro IPPs

OpenAIRE

Weaver, Tyson John

2013-01-01

This article addresses two primary commercial themes that affect the future development of the industry. 1. What are the most attractive future emerging markets for hydropower? 2. What parameters are utilized by international hydro IPPs to determine market attractiveness?

IPP (Max-Planck-Institute for Plasma Physics) annual report 1986

International Nuclear Information System (INIS)

1986-01-01

The scientific activities of IPP comprise two programmes, tokamaks and stellarators, the main results of which are summarized in two overviews introducing the corresponding sections in the body of the report. The scientific work is firmly integrated into a network of cooperation. In Germany, we collaborate with the Nuclear Research Center Karlsruhe in the 'Entwicklungsgemeinschaft Kernfusion'; of the collaboration with universities the most successful has been that with Stuttgart on ECRH. The IPP programme forms an integral part of the European fusion programme. (orig./GG)

Chemical synthesis of perfectly isotactic and high melting bacterial poly(3-hydroxybutyrate) from bio-sourced racemic cyclic diolide.

Science.gov (United States)

Tang, Xiaoyan; Chen, Eugene Y-X

2018-06-11

Bacterial poly(3-hydroxybutyrate) (P3HB) is a perfectly isotactic, crystalline material possessing properties suitable for substituting petroleum plastics, but high costs and low volumes of its production are impractical for commodity applications. The chemical synthesis of P3HB via ring-opening polymerization (ROP) of racemic β-butyrolactone has attracted intensive efforts since the 1960s, but not yet produced P3HB with high isotacticity and molecular weight. Here, we report a route utilizing racemic cyclic diolide (rac-DL) derived from bio-sourced succinate. With stereoselective racemic catalysts, the ROP of rac-DL under ambient conditions produces rapidly P3HB with perfect isotacticity ([mm] > 99%), high melting temperature (T m  = 171 °C), and high molecular weight (M n  = 1.54 × 10 5  g mol -1 , Đ = 1.01). With enantiomeric catalysts, kinetic resolution polymerizations of rac-DL automatically stops at 50% conversion and yields enantiopure (R,R)-DL and (S,S)-DL with >99% e.e. and the corresponding poly[(S)-3HB] and poly[(R)-3HB] with high T m  = 175 °C.

High-throughput enzyme screening platform for the IPP-bypass mevalonate pathway for isopentenol production

DEFF Research Database (Denmark)

Kang, Aram; Meadows, Corey W.; Canu, Nicolas

2017-01-01

Isopentenol (or isoprenol, 3-methyl-3-buten-1-ol) is a drop-in biofuel and a precursor for commodity chemicals such as isoprene. Biological production of isopentenol via the mevalonate pathway has been optimized extensively in Escherichia coli, yielding 70% of its theoretical maximum. However, high...... ATP requirements and isopentenyl diphosphate (IPP) toxicity pose immediate challenges for engineering bacterial strains to overproduce commodities utilizing IPP as an intermediate. To overcome these limitations, we developed an “IPP-bypass� isopentenol pathway using the promiscuous activity...

The role of intravesical prostatic protrusion (IPP) in the evaluation and treatment of bladder outlet obstruction (BOO).

Science.gov (United States)

Kuo, Tricia L C; Teo, Jonathan S M; Foo, K T

2016-04-01

Intravesical prostatic protrusion (IPP) may be an underutilized modality for the assessment of bladder outlet obstruction (BOO). Pressure flow studies or urodynamics have long been the gold standard for the evaluation of lower urinary tract symptoms (LUTS) in men but are invasive, time-consuming and costly. Potentially, IPP may be a useful adjunct prior to performing urodynamics. Measurement of IPP is taken in the sagittal view, using the transabdominal ultrasound. It is the vertical height from the tip of the protrusion to the base of the prostate. This technique was previously described. We reviewed previous publications that studied the accuracy, positive predictive value and clinical use of IPP. In addition, we noted the comments regarding the challenges of using this technique. IPP has been shown to have a positive predictive value of 72% for BOO. It has been calculated to have an area under curve (AUC) value of 0.71 and 0.84 in some stuies. Clinically, it may be used to predict the outcome of a trial without catheter following acute retention of urine. Patients with higher IPP grade were noted to have a higher risk of clinical progression. Studies have also shown that men with higher IPP are poorer responders to medical treatment such as α-blockers. Compared to other modalities, the advantage of IPP in assessing BOO may be its easy applicability and non-invasive nature. Therefore, there is a consideration for a larger role of IPP in bedside assessment and management of BOO in daily practice. Neurourol. Urodynam. 35:535-537, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

Designing tough and fracture resistant polypropylene/multi wall carbon nanotubes nanocomposites by controlling stereo-complexity and dispersion morphology

International Nuclear Information System (INIS)

Das, Dibyendu; Satapathy, Bhabani K.

2014-01-01

Highlights: • New pathway to improve dispersion and toughness by tacticity modification. • >330% toughness enhancement in PP/MWCNT nanocomposites with stereo-complex PP. • Prominent dispersion and distribution morphology due to matrix stereocomplexity. • Tacticity induced “Semi-ductile-to-tough-to-quasi-brittle” transitions in the PP/MWCNT. • Two-fold reduced steady state CTOD rate in i-PP+s-PP/ MWCNT nanocomposites. - Abstract: A remarkable toughness enhancement (>330%) of multi wall carbon nanotubes (MWCNT) filled stereo-complex polypropylene (PP) matrix i.e. blend of isotactic-PP and syndiotactic-PP (70:30) with differences in stereo-regularity has been observed. The enhancement has been correlated to quantifiable morphological parameters such as free-space lengths concerning dispersion and relatively greater reduction in crystallite size/lamellar thickness. Systematic analysis of glass transition data and estimation of multi wall carbon nanotubes induced reduction in interfacial polymer chain immobilization reiterates susceptibility of polymer segments to ready-mobility. The extent of toughening has quantitatively been analyzed by fracture-energy partitioning, essential work of fracture (EWF), approach enabling the detection of a “semi-ductile-to-tough-to-quasi-brittle” transition in the MWCNT filled stereo-complex polypropylene. Real-time fracture kinetics analysis revealed toughening mechanism to be primarily blunting-assisted; an aspect also corroborated by extensive plastic flow without much energy dissipation in the inner fracture process zone. Thus the study establishes a new pathway of tacticity-defined matrix modification to toughen nanocomposites

Integrated Personnel and Pay System-Army Increment 2 (IPPS-A Inc 2)

Science.gov (United States)

2016-03-01

system maintenance, and minimizing pay discrepancies . IPPS-A Inc 2 will account for status changes between Active, Reserve, and National Guard components...2016 Major Automated Information System Annual Report Integrated Personnel and Pay System-Army Increment 2 (IPPS-A Inc 2) Defense Acquisition...703-325-3747 DSN Phone: 865-2915 DSN Fax: 221-3747 Date Assigned: May 2, 2014 Program Information Program Name Integrated Personnel and Pay System

Influence of residual stress on the adhesion and surface morphology of PECVD-coated polypropylene

Science.gov (United States)

Jaritz, Montgomery; Hopmann, Christian; Behm, Henrik; Kirchheim, Dennis; Wilski, Stefan; Grochla, Dario; Banko, Lars; Ludwig, Alfred; Böke, Marc; Winter, Jörg; Bahre, Hendrik; Dahlmann, Rainer

2017-11-01

The properties of plasma-enhanced chemical vapour deposition (PECVD) coatings on polymer materials depend to some extent on the surface and material properties of the substrate. Here, isotactic polypropylene (PP) substrates are coated with silicon oxide (SiO x ) films. Plasmas for the deposition of SiO x are energetic and oxidative due to the high amount of oxygen in the gas mixture. Residual stress measurements using single Si cantilever stress sensors showed that these coatings contain high compressive stress. To investigate the influence of the plasma and the coatings, residual stress, silicon organic (SiOCH) coatings with different thicknesses between the PP and the SiO x coating are used as a means to protect the substrate from the oxidative SiO x coating process. Pull-off tests are performed to analyse differences in the adhesion of these coating systems. It could be shown that the adhesion of the PECVD coatings on PP depends on the coatings’ residual stress. In a PP/SiOCH/SiO x -multilayer system the residual stress can be significantly reduced by increasing the thickness of the SiOCH coating, resulting in enhanced adhesion.

Pathophysiologie des Kollagenstoffwechsels bei Patienten mit Induratio penis plastica (IPP

Directory of Open Access Journals (Sweden)

Lahme S

2000-01-01

Full Text Available Die Pathogenese der IPP ist bis heute nicht geklärt. Histopathologische Untersuchungen zeigen, daß der Kollagenstoffwechsel eine Rolle spielt. Dies veranlaßte uns zur genauen Analyse der Kollagenstoffwechselparameter bei IPP. Bei 11 Patienten mit IPP und 11 Kontrollpersonen wurden Kollagenstoffwechselparameter (Prokollagen III [PIIIP], PMN-Elastase [PMN-E], Fibronektin [FN], Fibronektinrezeptor [FN-R] und alpha1-Proteinase-Inhibitor [alpha1-PI] im cavernösen und peripheren Blut bestimmt. PMN-E, PIIIP, FN und FN-R waren in den beiden Untersuchungsgruppen nicht unterschiedlich. Die peripher venösen unterschieden sich nicht von den cavernösen Blutproben. Sowohl im peripher venös (158,55 mg/dl als auch im cavernös entnommenen Blut (168,29 mg/dl war die Konzentration des a1-PI signifikant niedriger als in der Kontrollgruppe (214,82 mg/dl. An einem zweiten Kollektiv von 23 Patienten wurden Analysen des Phänotyps für alpha1-PI im Hinblick auf das Vorliegen von genetisch determinierten Mangelallelen vorgenommen. Hier zeigte sich kein signifikanter Unterschied zu einem Kontrollkollektiv von 19 gesunden Probanden. Die alpha1-PI Erniedrigung der IPP-Patienten ist signifikant und liegt unterhalb des Normalwertbereichs für die gesunde Population. Ein Mangel an alpha1-PI kann zur Aktivitätserhöhung der Proteasen und zum Umbau des Kollagengewebes führen. Möglicherweise kommt es zusammen mit einem lokal wirksamen Einflußfaktor schließlich zur dystrophen Kalzifikation. Die humangenetischen Untersuchungen sprechen nicht für eine genetische Determinierung des alpha1-PI-Mangels, sondern legen eine erworbene hepatische Störung nahe.

VAR IPP-IPC Model Simulation

Directory of Open Access Journals (Sweden)

Juan P. Pérez Monsalve

2014-12-01

Full Text Available This work analyzed the relationship of the two main Price indicators in the Colombian economy, the IPP and the IPC. For this purpose, we identified the theory comprising both indexes to then develop a vector autoregressive model, which shows the reaction to shocks both in itself as in the other variable, whose impact continues propagating in the long term. Additionally, the work presents a simulation of the VAR model through the Monte Carlo method, verifying the coincidence in distributions of probability and volatility levels, as well as the existence correlation over time

Using rheometry for determining nucleation density in colored system containing a nucleation agent

NARCIS (Netherlands)

Ma, Z.; Steenbakkers, R.J.A.; Giboz, J.; Peters, G.W.M.

2011-01-01

A new suspension-based rheological method was applied to study experimentally the crystallization of a nucleating agent (NA) filled isotactic polypropylene. This method allows for determination of point-nucleation densities where other methods fail. For example, optical microscopy can fail because

The influences of the physical-chemical factors on the free-volume relations in polymers

International Nuclear Information System (INIS)

Bartos, J.; Kristiak, J.; Kristiakova, K.; Sausa, O.; Bandzuch, P.

1995-01-01

The positron annihilation spectroscopy was used to the study of different physical-chemical factors on the free-volume microstructure of the model polymeric systems [amorphous 1,4-cis-poly(butadiene), amorphous a-tactic and semi-crystal iso-tactic poly(propylene), polycarbonate

Japanese electric utilities call for IPP capacity

Energy Technology Data Exchange (ETDEWEB)

Jeffs, E.

1997-03-01

Japan`s ten power utilities have finally grasped the nettle, and called in IPPs to supply at least 3 GW of new capacity in each of the next ten years. The first twenty schemes awarded last year are all based on existing industrial energy producers, and consist mainly of coal- or oil-fired plants of 150 MW or less. 1 tab.

Contact mechanics of polyolefins: effect of pre-stretch on the frictional response and the onset of wear

NARCIS (Netherlands)

Looijmans, S.F.S.P.; Anderson, P.D.; van Breemen, L.C.A.; Crosby, A.J.; Govaert, L.E.

2018-01-01

As a result of processing history, polymer products are, more often than not, anisotropic. In this work, single-asperity sliding friction experiments are used to characterize the tribology of semi-crystalline polymer films. We show the improved scratch resistance of oriented isotactic polypropylene

IPPS Provider Summary for the Top 100 DRGs - FY2011

Data.gov (United States)

U.S. Department of Health & Human Services — A provider level summary of Inpatient Prospective Payment System (IPPS) discharges, average charges and average Medicare payments for the Top 100 Diagnosis-Related...

Resonance – Journal of Science Education | Indian Academy of ...

Indian Academy of Sciences (India)

The story of how Natta discoveredpolypropylene is an engrossing one – one of stiff competitionamongst contemporaries, Natta's intimate relationship withthe Italian industries, and his unique scientific background.Natta's identification of isotactic polypropylene as a righthandedthree fold 'single helix' in March 1954, in quick ...

Biodegradation of Polypropylene Nonwovens

Science.gov (United States)

Keene, Brandi Nechelle

The primary aim of the current research is to document the biodegradation of polypropylene nonwovens and filament under composting environments. To accelerate the biodegradat ion, pre-treatments and additives were incorporated into polypropylene filaments and nonwovens. The initial phase (Chapter 2) of the project studied the biodegradation of untreated polypropylene with/without pro-oxidants in two types of composting systems. Normal composting, which involved incubation of samples in food waste, had little effect on the mechanical properties of additive-free spunbond nonwovens in to comparison prooxidant containing spunbond nonwovens which were affected significantly. Modified composting which includes the burial of samples with food and compressed air, the polypropylene spunbond nonwovens with/without pro-oxidants displayed an extreme loss in mechanical properties and cracking on the surface cracking. Because the untreated spunbond nonwovens did not completely decompose, the next phase of the project examined the pre-treatment of gamma-irradiation or thermal aging prior to composting. After exposure to gamma-irradiation and thermal aging, polypropylene is subjected to oxidative degradation in the presence of air and during storage after irradiat ion. Similar to photo-oxidation, the mechanism of gamma radiation and thermal oxidative degradation is fundamentally free radical in nature. In Chapter 3, the compostability of thermal aged spunbond polypropylene nonwovens with/without pro-oxidant additives. The FTIR spectrum confirmed oxidat ion of the polypropylene nonwovens with/without additives. Cracking on both the pro-oxidant and control spunbond nonwovens was showed by SEM imaging. Spunbond polypropylene nonwovens with/without pro-oxidants were also preirradiated by gamma rays followed by composting. Nonwovens with/without pro-oxidants were severely degraded by gamma-irradiation after up to 20 kGy exposure as explained in Chapter 4. Furthermore (Chapter 5), gamma

Engineering new polypropylene copolymer for asphalt modification. Progettazione di un polimero a base polipropilenica adatto per la modifica dei bitumi

Energy Technology Data Exchange (ETDEWEB)

Giavarini, C.; Santarelli, M.L. (Rome Univ. (Italy). Dipt. di Ingegneria Chimica); Braga, V. (Himont Centro Ricerche ' G. Natta' , Ferrara (Italy))

1993-04-01

Polypropylene polymers: isotactic PP, random, heterophasic copolymer, ethylene-propylene rubber, are suitable as modifiers for road bitumens. Among the advantages of PP polymers, such as heterophasic polymers, prepared via synthesis, are good thermal and ageing resistance, and the fact that they can be easily tailored to the specific application. Various types of PP and EPR polymers, possibly blended, prepared or modified for this purpose, were mixed with bitumens to study the dispersion of the polymer, segregation characteristics, ageing and viscoelastic properties. The experimental results gave indications on the characteristics of a polyolefinic copolymer for bitumen modification. The PP based products applicable as bitumen modifiers are the heterophasic copolymers containing a substantial amounts of EPR, possibly modified to increase branching. For road bitumens with a penetration between 100 and 200 dmm, the average molecular weight of the polymer should be arranged to reach an intrinsic viscosity between about 1.5 and 2.0 dl/g. Partial branching (or partial crosslinking) of the chains in the PP-phase is helpful when not followed by EPR-phase crosslinking.

Induratio penis plastica (IPP) and laser: a review

Science.gov (United States)

Longo, Leonardo; Mancini, S.; Postiglione, M. G.

2002-10-01

The first employments of Laser therapy for I.P.P. came from back to more than twenty years ago. At the beginning it was employed only in the acute forms as analgesic laser laser was used also as anti-inflammatory following the doses of Low Level Laser Therapy. Than the science tried to use the laser effect remodelling phase of the scars, to make the fibrosis regrade in the chronic forms. Tunable laser in small optical fiber was used for ablation of calcified zones with very good results. For the slight forms were used diode laser 660 and 904 nm, alone ir coupling with CO2 laser with large spot. At first some Author used helium-Neon laser 632. Some of these lasers were combined wtih microiontophoresis and ultrasounds therapy in teh same treatment. Now we use 810 nm surgical diode laser in almost all induratio forms. The immediate results and follow up will be discussed. Thanks to these results we could conclude that IPP laser therapy can be effective in most of the clinic forms. Although the used procedure is subject to improvement.

IPP annual report 1985/86

International Nuclear Information System (INIS)

1986-01-01

This annual report also is a review compiled on the occasion of the 25th anniversary of the Institute. A survey of tasks and activities of the IPP is followed by brief reports on the work in progress and on results achieved, dealing with the fundamentals of thermonuclear fusion, magnetic field configurations of the Tokamak device and stellarator device, and with the various components of a fusion experimental installation. Cooperative projects with other research institutes, the scientific infrastructure, the administrative organisation, services, and the activities of the management and of the scientific-technical office are other aspects forming part of the report. The organisational chart given is of November 1986. (GG) [de

From atactic to isotactic CO/p-methylstyrene copolymer by proper modification of Pd(II) catalysts bearing achiral alpha-diimines.

Science.gov (United States)

Binotti, Barbara; Carfagna, Carla; Zuccaccia, Cristiano; Macchioni, Alceo

2005-01-07

Cationic Pd(II) complexes modified with achiral C(2v)-symmetric alpha-diimine ligands allow preparation of atactic or isotactic stereoblock CO/p-methylstyrene copolymers; both catalyst activity and polyketone microstructure depend on the choice of alpha-diimine substituents and counterion.

Effect of Reinforcement of Hydrophobic Grade Banana (Musa ornata Bark Fiber on the Physicomechanical Properties of Isotactic Polypropylene

Directory of Open Access Journals (Sweden)

Md. Mamunur Rashid

2016-01-01

Full Text Available This research studied the physicomechanical as well as morphological properties of alkali treated (NaOH and KMnO4 and untreated banana bark fiber (BBF reinforced polypropylene composites. A detailed structural and morphological characterization was performed using Fourier transform infrared spectroscopy (FTIR, scanning electron microscopy (SEM, and mechanical properties testing (tensile strength, flexural strength, and microhardness. Chemical treatments improved the hydrophobic property of the fiber and it is found to be better for KMnO4 treatment. Composites with 0, 5, 10, and 15 wt.% loadings were then compared for water uptake studies and revealed that KMnO4 treated fiber composites absorb less water compared to others. KMnO4 treatment with 15% fiber loading improved the tensile strength, flexural strength, and microhardness of the composites compared to raw and NaOH treated fiber loadings. TGA analysis also shows onset temperature at 400~500°C that is associated with the decomposition of the banana fibers constituents including lignin, cellulose, and hemicelluloses which suggests better thermomechanical stability. All of the values suggest that 15% KMnO4 treated banana bark fiber (BBF/PP composites were found to be better than those of the raw and NaOH treated ones.

Prospective production of radioisotopes and radiopharmaceuticals in divisions of IPPE

International Nuclear Information System (INIS)

Terentyev, G.O.

2001-01-01

The first reason to commence the work on production of radioisotope production in IPPE, was the requirement of Russia medicine for original generators of technetium. The essential extension of their production in conditions of Moscow city has met the declaiming of the Moscow urban authorities. The important moment was that, in IPPE were objective possibilities to deployment the production of radioisotope production. Nowadays, nomenclature of the radioisotopes which have been produced in IPPE, constitutes 29 positions. The profile of production of radioisotope production was generated also. Restricted possibilities of the ray base, from one side, and the needs(requirement) of domestic medicine with other, in main have spotted this profile. The raw isotopes constitute a minority - on sales volumes ∼ 20 % (in main abroad), the defining part is constituted the form ready for the use by ∼ 80 % (in main in Russia). All 'know-how' is conditionally possible to divide into 3 categories: Base. It is technologies provided with an operating production sector, guaranteeing stable on quality production having a rather wide seller's market; Perspective. It is those technologies, in which the main stages of RESEARCH and DEVELOPMENT are fulfilled with positive result, but the working sites yet are not generated, and on the market are delivered only some samples of production. Are guessed RESEARCH AND DEVELOPMENT on perfecting the technology; Preparative. The technology, on which there are no regular orders, is not required of an individual working site. Sometimes it is rather precision operations, bound with usage of unique raw material, with a very stiff price of production. (authors)

The radiation chemistry of macromolecules

CERN Document Server

1973-01-01

The Radiation Chemistry of Macromolecules, Volume II is a collection of papers that discusses radiation chemistry of specific systems. Part 1 deals with radiation chemistry of substituted vinyl polymers, particularly polypropylene (PP) as its structure is intermediate between polyethylene and polyisobutylene. This part also discusses polypropylene oxide (PPOx) for it can be prepared in the atactic, isotactic, and optically active forms. One paper focuses on the fundamental chemical processes and the changes in physical properties that give rise to many different applications of polystyrene. An

Role of PET in improving wear properties of PP in dry sliding condition

Indian Academy of Sciences (India)

Unknown

... blends were studied using scanning elec- tron microscopy. Sliding wear properties of these blends have been determined and studied for various blend com- positions. 2. Materials and methods. 2.1 Materials. Isotactic polypropylene PP (density 0⋅91 g/cc, grade SRM. 100 N) was obtained from M/s Indian Petrochemicals.

Safety evaluation of an IPP tripeptide-containing milk protein hydrolysate

NARCIS (Netherlands)

Ponstein-Simarro Doorten, A.Y.; Wiel, J.A.G. van de; Jonker, D.

2009-01-01

Tensguard™ is a milk protein hydrolysate containing the lactotripeptide IPP. It is derived from cow's milk, which is present in the human diet and has a safe history of consumption. The final Tensguard™ product, a supplement or a functional food ingredient, is intended for use by people who want to

Photooxidation of HMS-PP under environment and artificial weathering conditions

International Nuclear Information System (INIS)

Oliani, Washington L.; Parra, Duclerc F.; Lima, Luis Filipe C.P.; Lugao, Ademar B.

2009-01-01

The linearity of the chains confers to iPP, low melt strength, which means a low strength to stretching during elongation. The increase of melt strength and the extensibility is due to the increase of the entanglement of the macromolecules chains. The HMS-PP (high melt strength polypropylene) was synthesized (based on the grains iPP) through gamma irradiation in the iPP under acetylene atmosphere followed by heat treatment for recombination and subsequent annihilation of the other free radicals. Samples of HMS-PP and iPP were subjected to environmental aging in IPEN - Sao Paulo and in the QUV chamber. The results show fractured surfaces of iPP and HMS-PP that are intensified with exposure time. The iPP degradation process has the predominance of chain scissions, with carbonyl and hydroperoxides formation which act as initiators of photo degradation mechanisms. (author)

Photooxidation of HMS-PP under environment and artificial weathering conditions;Fotooxidacao do HMS-PP sob condicoes de intemperismo ambiental e artificial

Energy Technology Data Exchange (ETDEWEB)

Oliani, Washington L.; Parra, Duclerc F.; Lima, Luis Filipe C.P.; Lugao, Ademar B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2009-07-01

The linearity of the chains confers to iPP, low melt strength, which means a low strength to stretching during elongation. The increase of melt strength and the extensibility is due to the increase of the entanglement of the macromolecules chains. The HMS-PP (high melt strength polypropylene) was synthesized (based on the grains iPP) through gamma irradiation in the iPP under acetylene atmosphere followed by heat treatment for recombination and subsequent annihilation of the other free radicals. Samples of HMS-PP and iPP were subjected to environmental aging in IPEN - Sao Paulo and in the QUV chamber. The results show fractured surfaces of iPP and HMS-PP that are intensified with exposure time. The iPP degradation process has the predominance of chain scissions, with carbonyl and hydroperoxides formation which act as initiators of photo degradation mechanisms. (author)

Radiation crosslinking of polypropylene

International Nuclear Information System (INIS)

Nojiri, A.; Sawasaki, T.

1984-01-01

The radiation crosslinking of polypropylene with several kinds of polyfunctional monomers has been examined, and it has been clarified that the enhanced crosslinking may be classified into two types. In particular, the irradiation crosslinking process of polypropylene containing a polyfunctional monomer having an acryloyloxy group giving a specific gel - dose curve has been studied by infrared absorption spectrum and oxygen absorptivity measurement in comparison with the non-enhanced system. (author)

The radiation degradation of polypropylene

International Nuclear Information System (INIS)

De Hollain, G.

1977-04-01

Polypropylene is used extensively in the manufacture of disposable medical devices because of its superior properties. Unfortunately this polymer does not lend itself well to radiation sterilization, undergoing serious degradation which affects the mechanical properties of the polymer. In this paper the effects of radiation on the mechanical and physical properties of polypropylene are discussed. A programme of research to minimize the radiation degradation of this polymer through the addition of crosslinking agents to counteract the radiation degradation is proposed. It is furthermore proposed that a process of annealing of the irradiated polymer be investigated in order to minimize the post-irradiation degradation of the polypropylene [af

Influência da estrutura do catalisador a base de Zirconoceno na estereorregularidade e propriedades do polipropileno formado Influence of Zirconocene structure on polypropylene stereorregularity and properties

Directory of Open Access Journals (Sweden)

Mário R. Meneghetti

1997-03-01

Full Text Available RESUMO: Catalisadores de metalocenos com diferentes simetrias, cocatalisados por metilaluminoxanas (MAO, foram avaliados em diferentes temperaturas de polimerização do propileno. Os metalocenos com ponte interanelar, ou seja, o dicloreto de rac-etileno bis(h5-1-indenil zircônio, com simetria C2, e o dicloreto de isopropilideno(h5-ciclopentadienil(h5-9-fluorenil zircônio, com simetria Cs, produziram, respectivamente, polipropileno isotático e sindiotático. O grau de taticidade desses polímeros diminui com o aumento da temperatura de polimerização. Os metalocenos sem ponte, dicloreto de bis(h5-ciclopentadienilzircônio e bis(h5-indenilzircônio, em qualquer uma das temperaturas investigadas, produziram, somente, polipropileno atático. A estereorregularidade dos polímeros foram determinadas por Ressonância Magnética Nuclear de 13C.ABSTRACT: Metallocenes with different symmetries in combination with methylaluminoxane (MAO, have been investigated at different propylene polymerization temperatures. The metallocenes rac-ethylene bis(h5-1-indenyl zirconium dichloride, with C2 symmetry and isopropylidene (h5cyclopentadienyl(h5-9-fluorenyl zirconium dichloride, with Cs symmetry, produce isotactic and syndiotactic polypropylene respectively. The degree of tacticity of these polymers decreases with the increase of polymerization temperature. Only atactic polypropylene was formed with the unbridged zirconocenes bis(h5-cyclopentadienyl zirconium dichloride and bis(h5-indenyl zirconium dichloride at any temperature investigated. The polymer microtacticity was analysed by 13C NMR.

Numerical simulations of the IPPE target geometry flows

International Nuclear Information System (INIS)

Prakash, Akshay; Kakarantzas, Sotiris; Bernardi, Davide; Micciche, Gioacchino; Massaut, Vincent; Knaepen, Bernard

2013-01-01

Highlights: ► We performed numerical simulation of flow over IPPE geometry using turbulence models in FLUENT. ► Stable free surface profile well within the required design limits was predicted by the models. ► Velocity profiles across the liquid jet and jet thickness different for different models. ► There were some 3D effects noticeable for the velocity profiles but the predicted jet thickness similar to 2D models. ► TKE predicted by different models close to each other and compare will with published data. -- Abstract: A high speed water and liquid lithium (Li) flow is computed over the IPPE geometry to evaluate the performance of different turbulence models in 2D and 3D simulations. Results reported are the thickness of the liquid jet, irregularities in the surface, transient phenomena at the wall which can affect fluid surface and effect of the variation in bulk velocity on these quantities. All models show good near wall resolution of the boundary layer and expected profiles for the free surface flow. Predicted turbulent kinetic energy compare well with published data. Fluctuations of the flow surface at the control location (center of the curved section) and elsewhere are well within 1 mm for all models. However it was observed that the predictions are strongly dependent on the model used. Overall, the predictions of RANS models are close to each other whereas predictions of laminar simulations are close to those obtained with LES models

Radiation resistant modified polypropylene

International Nuclear Information System (INIS)

Bojarski, J.; Zimek, Z.

1997-01-01

Radiation technology for production of radiation resistant polypropylene for medical use has been presented. The method consists in radiation induced copolymerization of polypropylene with ethylene and addition of small amount of copolymer of polyethylene and vinyl acetate. The material of proposed composition has a very good mechanical properties and elevated radiation resistivity decided on possibility of radiosterilization of products made of this material and designed for medical use. 3 figs, 3 tabs

Synergistic reinforcement of highly oriented poly(propylene) tapes by sepiolite nanoclay

NARCIS (Netherlands)

Bilotti, E.; Deng, H.; Zhang, R.; Lu, D.; Bras, W.; Fischer, H.R.; Peijs, T.

2010-01-01

This paper reports the properties of highly oriented nanocomposite tapes based on isotactic PP and needle-like sepiolite nanoclay, obtained by a solid state drawing process. The intrinsic 1D character of sepiolite allows its exploitation in 1D objects, such as oriented polymer fibres and tapes,

Permeation Tests on Polypropylene Fiber Materials

Science.gov (United States)

2018-03-16

Permeation Tests on Polypropylene Fiber Materials Brandy J. White Martin H. Moore Brian J. Melde Laboratory for the Study of Molecular Interfacial...ABSTRACT Permeation Tests on Polypropylene Fiber Materials Brandy J. White, Martin H. Moore, Brian J. Melde Center for Bio/Molecular Science

Green aqueous surface modification of polypropylene for novel polymer nanocomposites.

Science.gov (United States)

Thakur, Vijay Kumar; Vennerberg, Danny; Kessler, Michael R

2014-06-25

Polypropylene is one of the most widely used commercial commodity polymers; among many other applications, it is used for electronic and structural applications. Despite its commercial importance, the hydrophobic nature of polypropylene limits its successful application in some fields, in particular for the preparation of polymer nanocomposites. Here, a facile, plasma-assisted, biomimetic, environmentally friendly method was developed to enhance the interfacial interactions in polymer nanocomposites by modifying the surface of polypropylene. Plasma treated polypropylene was surface-modified with polydopamine (PDA) in an aqueous medium without employing other chemicals. The surface modification strategy used here was based on the easy self-polymerization and strong adhesion characteristics of dopamine (DA) under ambient laboratory conditions. The changes in surface characteristics of polypropylene were investigated using FTIR, TGA, and Raman spectroscopy. Subsequently, the surface modified polypropylene was used as the matrix to prepare SiO2-reinforced polymer nanocomposites. These nanocomposites demonstrated superior properties compared to nanocomposites prepared using pristine polypropylene. This simple, environmentally friendly, green method of modifying polypropylene indicated that polydopamine-functionalized polypropylene is a promising material for various high-performance applications.

Flammability of polypropylene/organoclay nanocomposites

International Nuclear Information System (INIS)

Alves, Tatianny Soares; Barbosa, Renata; Carvalho, Laura Hecker de; Canedo, Eduardo Luis

2014-01-01

The flammabilities of nanocomposites made with three polypropylene grades (homo and copolymers) with 5 wt % of organoclay (Cloisite 20A), 5 or 15 wt % of maleated polypropylene as compatibilizer, and 0, 0.5 or 1 wt % of cis-13-docosenamide (Erucamide) as co-intercalant, were studied using the horizontal burning test UL94HB. Masterbatches prepared in an internal mixer were diluted in the polypropylene matrix using a corotating twin-screw extruder, with different screw configurations and operating at 240 or 480 rpm. Results indicate that the high burning rate of the composites was not affected by the processing conditions. For all formulations was observed a significant reduction in smoke release, lack of dripping and the formation of a char surface layer, that protected the core of the samples. (author)

The use of maleic anhydride-modified polypropylene for performance enhancement in continuous glass fiber-reinforced polypropylene composites

NARCIS (Netherlands)

Rijsdijk, H.A.; Contant, M.; Peijs, A.A.J.M.; Miravete, A.

1993-01-01

The influence of maleic anhydride-modified polypropylene (m-PP) on static mech. properties of continuous glass fiber-reinforced polypropylene (PP) composites was studied. M-PP was added to the PP homopolymer to improve the adhesion between the matrix and the glass fiber. Three-point bending tests

Inpatient Prospective Payment System (IPPS) Provider Summary for the Top 100 Diagnosis-Related Groups (DRG)

Data.gov (United States)

U.S. Department of Health & Human Services — A provider level summary of Inpatient Prospective Payment System (IPPS) discharges, average charges and average Medicare payments for the Top 100 Diagnosis-Related...

Preparation of Polypropylene/Montmorillonite Nanocomposites Using Ionizing Radiation

International Nuclear Information System (INIS)

Güven, Olgun; Zengin, Fatma

2011-01-01

Polymer/clay nanocomposites are new generation materials that bring significant changes in mechanical, thermal and permeation properties of base polymers by low clay loading. In this study, polypropylene/montmorillonite nanocomposites were prepared by melt intercalation method by using batch type mixer. Two polypropylene samples with different melt flow indexes are used as the matrix, maleic anhydride grafted polypropylene (PP-g-MAH), and polypropylene granules oxidized by radiation/ozone are used as compatibilizer and unmodified clay (Na + montmorillonite, MMT) as the filler. Aim of this study is to examine the effect of different compatibilizers in the mechanical properties of polypropylene composite. Firstly, PP/clay samples were prepared and the effect of clay was examined, then 5, 10, 20kGy oxidized/degraded polypropylenes were used as compatibilizer and, 10 kGy was determined to be the most suitable irradiation dose for the best compatibilizing effect. Polypropylene granules were ozonated until they contained carbonyl groups equivalent to 10kGy oxidized PP, which was checked by FTIR-ATR spectroscopy. UV-visible reflectance measurements were also made on film samples and no significant changes were observed in visible region. Nano structures of some nanocomposites were characterized by PALS (Positron Annihilation Lifetime Spectroscopy) where it was observed that the addition of clay decreased the number of free volume holes and free volume hole radia. The dispersion state of MMT within polymer matrix was analyzed by XRD (X-ray diffraction). Tensile tests were made and the effect of the addition of clay and compatibilizers investigated. At low melt flow index PP, 1% MMT of PP/10kGyPP/MMT nanocomposite showed an increase in E-modulus 26% and in tensile strength 8% as compared to those of pristine PP. In conclusion radiation degraded (chain scissioned and oxidized) PP has been found to show very good compatibilizing effect for the natural montmorillonite/polypropylene

Preparation of Polypropylene/Montmorillonite Nanocomposites Using Ionizing Radiation

Energy Technology Data Exchange (ETDEWEB)

Güven, Olgun; Zengin, Fatma

2011-07-01

Polymer/clay nanocomposites are new generation materials that bring significant changes in mechanical, thermal and permeation properties of base polymers by low clay loading. In this study, polypropylene/montmorillonite nanocomposites were prepared by melt intercalation method by using batch type mixer. Two polypropylene samples with different melt flow indexes are used as the matrix, maleic anhydride grafted polypropylene (PP-g-MAH), and polypropylene granules oxidized by radiation/ozone are used as compatibilizer and unmodified clay (Na{sup +} montmorillonite, MMT) as the filler. Aim of this study is to examine the effect of different compatibilizers in the mechanical properties of polypropylene composite. Firstly, PP/clay samples were prepared and the effect of clay was examined, then 5, 10, 20kGy oxidized/degraded polypropylenes were used as compatibilizer and, 10 kGy was determined to be the most suitable irradiation dose for the best compatibilizing effect. Polypropylene granules were ozonated until they contained carbonyl groups equivalent to 10kGy oxidized PP, which was checked by FTIR-ATR spectroscopy. UV-visible reflectance measurements were also made on film samples and no significant changes were observed in visible region. Nano structures of some nanocomposites were characterized by PALS (Positron Annihilation Lifetime Spectroscopy) where it was observed that the addition of clay decreased the number of free volume holes and free volume hole radia. The dispersion state of MMT within polymer matrix was analyzed by XRD (X-ray diffraction). Tensile tests were made and the effect of the addition of clay and compatibilizers investigated. At low melt flow index PP, 1% MMT of PP/10kGyPP/MMT nanocomposite showed an increase in E-modulus 26% and in tensile strength 8% as compared to those of pristine PP. In conclusion radiation degraded (chain scissioned and oxidized) PP has been found to show very good compatibilizing effect for the natural montmorillonite/polypropylene

Selective laser vaporization of polypropylene sutures and mesh

Science.gov (United States)

Burks, David; Rosenbury, Sarah B.; Kennelly, Michael J.; Fried, Nathaniel M.

2012-02-01

Complications from polypropylene mesh after surgery for female stress urinary incontinence (SUI) may require tedious surgical revision and removal of mesh materials with risk of damage to healthy adjacent tissue. This study explores selective laser vaporization of polypropylene suture/mesh materials commonly used in SUI. A compact, 7 Watt, 647-nm, red diode laser was operated with a radiant exposure of 81 J/cm2, pulse duration of 100 ms, and 1.0-mm-diameter laser spot. The 647-nm wavelength was selected because its absorption by water, hemoglobin, and other major tissue chromophores is low, while polypropylene absorption is high. Laser vaporization of ~200-μm-diameter polypropylene suture/mesh strands, in contact with fresh urinary tissue samples, ex vivo, was performed. Non-contact temperature mapping of the suture/mesh samples with a thermal camera was also conducted. Photoselective vaporization of polypropylene suture and mesh using a single laser pulse was achieved with peak temperatures of 180 and 232 °C, respectively. In control (safety) studies, direct laser irradiation of tissue alone resulted in only a 1 °C temperature increase. Selective laser vaporization of polypropylene suture/mesh materials is feasible without significant thermal damage to tissue. This technique may be useful for SUI procedures requiring surgical revision.

Conductive polypropylene composites

International Nuclear Information System (INIS)

Koszkul, J.

1997-01-01

The results of studies on polypropylene composites with three sorts of Polish-made carbon blacks were presented. It was found that composite of 20% black content had properties of an electrically conducting material

Extraction of Micro- and Nano-Fibrils from Nylon 6/Polypropylene Grafted with Maleic Anhydride/Polypropylene Blended Films

Directory of Open Access Journals (Sweden)

E. Bagheban Kochak

2013-01-01

Full Text Available Atechnical feasibility study has been conducted on production of nano- and micro-fibrils from nylon 6/polypropylene grafted with maleic anhydride/polypropylene blended films. Fibrils are prepared in four consecutive steps.In the first step the polymers melt blended in an extruder with and without compatibilizers to produce chips; in the second step films are extruded from polymer blends chips, in the third step films are cold drawn with different draw ratios at room temperature and in the forth step fibrils are extracted by Soxhlet extraction with formic acid as solvent for nylon 6.  The films and fibrils were examined by scanning electron microscope and FTIR spectroscopy. It is found that the polypropylene dispersed phase deforms and coalesces into elongated fibrils during drawing  operation. The  fibrils’ diameters in the blends containing compatibilizer are more uniform and are smaller than those from films without compatibilizers. The thinnest polypropylene fibril observed has a diameter around 300 nm with the aspect ratio above 150. The stress-elongation curves show three distinctive regions, elastic, yield and hardening-leading to breakage. The elastic region is short and follows by necking and yield, i.e., elongation without increase in load. The hardening region is accompanied by the increase in the slope. The deformations of the polypropylene particles are noticed during the last regions of the extension; the fibril deformations seem to be more severe during breakage.

Preparation and Characterization of Extruded Composites Based on Polypropylene and Chitosan Compatibilized with Polypropylene-Graft-Maleic Anhydride

Science.gov (United States)

Carrasco-Guigón, Fernando Javier; Rodríguez-Félix, Dora Evelia; Castillo-Ortega, María Mónica; Santacruz-Ortega, Hisila C.; Burruel-Ibarra, Silvia E.; Encinas-Encinas, Jose Carmelo; Plascencia-Jatomea, Maribel; Herrera-Franco, Pedro Jesus; Madera-Santana, Tomas Jesus

2017-01-01

The preparation of composites of synthetic and natural polymers represent an interesting option to combine properties; in this manner, polypropylene and chitosan extruded films using a different proportion of components and polypropylene-graft-maleic anhydride (PPgMA) as compatibilizer were prepared. The effect of the content of the biopolymer in the polypropylene (PP) matrix, the addition of compatibilizer, and the particle size on the properties of the composites was analyzed using characterization by fourier transform-infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), tensile strength, and contact angle, finding that in general, the addition of the compatibilizer and reducing the particle size of the chitosan, favored the physicochemical and morphological properties of the films. PMID:28772464

The next generation of IPPs: keeping the lights on in Indonesia

Energy Technology Data Exchange (ETDEWEB)

James Booker [PT Paiton Energy (Indonesia)

2004-07-01

The paper begins by looking at where Indonesia is going (National Electricity Master Plan, future electricity demand) before examining how Indonesia will get there (investment, government plans). Finally, where Paiton Energy is now (history and status today, after restructuring, problems to be overcome) and the next generation of IPPs (Paiton I expansion, risk structuring and allocation) are discussed. 6 figs. A separation file (James Booker.pdf, 15 pages) contains the overheads/viewgraphs of the presentation.

Fatigue mechanisms in unidirectional glass-fibre-reinforced polypropylene

DEFF Research Database (Denmark)

Gamstedt, E.K.; Berglund, L.A.; Peijs, T.

1999-01-01

Polypropylene (PP) and polypropylene modified with maleic anhydride (MA-PP) reinforced by continuous longitudinal glass fibres have been investigated. The most prominent effect of the modification with maleic anhydride in the composite is a stronger fibre/matrix interface. The effects of interfac......Polypropylene (PP) and polypropylene modified with maleic anhydride (MA-PP) reinforced by continuous longitudinal glass fibres have been investigated. The most prominent effect of the modification with maleic anhydride in the composite is a stronger fibre/matrix interface. The effects...... of interfacial strength on fatigue performance and on the underlying micromechanisms have been studied for these composite systems. Tension-tension fatigue tests (R = 0.1) were carried out on 0 degrees glass-fibre/PP and glass-fibre/ MA-PP coupons. The macroscopic fatigue behaviour was characterized in terms...

The effect of temperature and strain rate on the mechanical properties of highly oriented polypropylene tapes and all-polypropylene composites

NARCIS (Netherlands)

Alcock, B.; Cabrera, N.O.; Barkoula, N.M.; Reynolds, C.T.; Govaert, L.E.; Peijs, A.A.J.M.

2007-01-01

The creation of highly oriented, co-extruded polypropylene (PP) tapes allows the production of recyclable "all-polypropylene" (all-PP) composites, with a large temperature processing window and a high volume fraction of highly oriented PP (>90%). The wholly thermoplastic nature of these

How many Enrons? Mark-ups in the stated capital cost of independent power producers' (IPPs') power projects in developing countries

International Nuclear Information System (INIS)

Phadke, Amol

2009-01-01

I analyze the determinants of the stated capital cost of IPPs' power projects which significantly influences their price of power. I show that IPPs face a strong incentive to overstate their capital cost and argue that effective competition or regulatory scrutiny will limit the extent of the same. I analyze the stated capital costs of combined cycle gas turbine (CCGT) IPP projects in eight developing countries which became operational during 1990-2006 and find that the stated capital cost of projects selected without competitive bidding is 44-56% higher than those selected with competitive bidding, even after controlling for the effect of cost differences among projects. The extent to which the stated capital costs of projects selected without competitive bidding are higher compared those selected with competitive bidding, is a lower bound on the extent to which they are overstated. My results indicate the drawbacks associated with a policy of promoting private sector participation without an adequate focus on improving competition or regulation. (author)

Final Report for completed IPP-0110 and 0110A Projects: 'High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications'

International Nuclear Information System (INIS)

Brown, Ian

2009-01-01

The DOE-supported IPP (Initiatives for Proliferation Prevention) Project, IPP-0110, and its accompanying 'add-on project' IPP-0110A, entitled 'High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications' was a collaborative project involving the Lawrence Berkeley National Laboratory (LBNL) as the U.S. DOE lab; the US surface modification company, Phygen, Inc., as the US private company involved; and the High Current Electronics Institute (HCEI) of the Russian Academy of Sciences, Tomsk, Siberia, Russia, as the NIS Institute involved. Regular scientific research progress meetings were held to which personnel came from all participating partners. The meetings were held mostly at the Phygen facilities in Minneapolis, Minnesota (with Phygen as host) with meetings also held at Tomsk, Russia (HCEI as host), and at Berkeley, California (LBNL as host) In this way, good exposure of all researchers to the various different laboratories involved was attained. This report contains the Final Reports (final deliverables) from the Russian Institute, HCEI. The first part is that for IPP-0110A (the 'main part' of the overall project) and the second part is that for the add-on project IPP-0110A. These reports are detailed, and contain all aspects of all the research carried out. The project was successful in that all deliverables as specified in the proposals were successfully developed, tested, and delivered to Phygen. All of the plasma hardware was designed, made and tested at HCEI, and the performance was excellent. Some of the machine and performance parameters were certainly of 'world class'. The goals and requirements of the IPP Project were well satisfied. I would like to express my gratitude to the DOE IPP program for support of this project throughout its entire duration, and for the unparalleled opportunity thereby provided for all of the diverse participants in the project to join in this collaborative research. The

FinalReport for completed IPP-0110 and 0110A Projects:"High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications"

Energy Technology Data Exchange (ETDEWEB)

Brown, Ian

2009-09-01

The DOE-supported IPP (Initiatives for Proliferation Prevention) Project, IPP-0110, and its accompanying 'add-on project' IPP-0110A, entitled 'High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications' was a collaborative project involving the Lawrence Berkeley National Laboratory (LBNL) as the U.S. DOE lab; the US surface modification company, Phygen, Inc., as the US private company involved; and the High Current Electronics Institute (HCEI) of the Russian Academy of Sciences, Tomsk, Siberia, Russia, as the NIS Institute involved. Regular scientific research progress meetings were held to which personnel came from all participating partners. The meetings were held mostly at the Phygen facilities in Minneapolis, Minnesota (with Phygen as host) with meetings also held at Tomsk, Russia (HCEI as host), and at Berkeley, California (LBNL as host) In this way, good exposure of all researchers to the various different laboratories involved was attained. This report contains the Final Reports (final deliverables) from the Russian Institute, HCEI. The first part is that for IPP-0110A (the 'main part' of the overall project) and the second part is that for the add-on project IPP-0110A. These reports are detailed, and contain all aspects of all the research carried out. The project was successful in that all deliverables as specified in the proposals were successfully developed, tested, and delivered to Phygen. All of the plasma hardware was designed, made and tested at HCEI, and the performance was excellent. Some of the machine and performance parameters were certainly of 'world class'. The goals and requirements of the IPP Project were well satisfied. I would like to express my gratitude to the DOE IPP program for support of this project throughout its entire duration, and for the unparalleled opportunity thereby provided for all of the diverse participants in the project to join

Shear effects on crystallization behaviors and structure transitions of isotactic poly-1-butene

DEFF Research Database (Denmark)

Li, Jingqing; Guan, Peipei; Zhang, Yao

2014-01-01

Different melt pre-shear conditions were applied to isotactic poly-1-butene (iP-1-B) and the effect on the crystallization behaviors and the crystalline structure transitions of iP-1-B were investigated. The polarized optical microscope observations during isothermal crystallization process...... revealed that the applied melt pre-shear within the experimental range could enhance the nucleation of crystal II and accelerate the diameter growth of the formed spherulites. If the applied melt pre-shear rate was large enough, Shish-Kebabs structure could be formed. After the isothermal crystallization...... was formed in the melt pre-sheared iP-1-B samples. Further investigations were applied with synchrotron radiation instruments. Wide angle X-ray scattering (WAXS) and small angle X-ray scattering (SAXS) after the crystal transition showed that the applied melt pre-shear could result in orientated fine...

Coir dust reinforced recycled polypropylene composites

International Nuclear Information System (INIS)

Santos, Bianca B. dos; Costa, Marysilvia F. da; Thire, Rossana M. da S.M.

2015-01-01

The environmental impacts caused by disposed plastics encourage the search for new alternatives. Recycling polymers leads to the degradation of their mechanical properties, which can be modified by the addition of fillers. In this paper, recycled polypropylene from plastic cups with 2%, 5% and 10% of coir dust were produced with and without the addition of additives. These composites were characterized by tensile tests, X-ray diffraction, differential scanning calorimetry and scanning electron microscopy on the fracture surface. It was verified the effectiveness of the addition of coir dust in improving the elasticity modulus of recycled polypropylene besides the effectiveness of additives used in promoting the adhesion of the powder to the matrix. However, higher levels of coir dust caused the appearance of air bubbles inside the material, which contributed to its embrittlement. The addition of coir dust promoted a decrease in the degree of polypropylene crystallinity. (author)

IPP-rich milk protein hydrolysate lowers blood pressure in subjects with stage 1 hypertension, a randomized controlled trial

Directory of Open Access Journals (Sweden)

Kloek Joris

2010-11-01

Full Text Available Abstract Background Milk derived peptides have been identified as potential antihypertensive agents. The primary objective was to investigate the effectiveness of IPP-rich milk protein hydrolysates (MPH on reducing blood pressure (BP as well as to investigate safety parameters and tolerability. The secondary objective was to confirm or falsify ACE inhibition as the mechanism underlying BP reductions by measuring plasma renin activity and angiotensin I and II. Methods We conducted a randomized, placebo-controlled, double blind, crossover study including 70 Caucasian subjects with prehypertension or stage 1 hypertension. Study treatments consisted of daily consumption of two capsules MPH1 (each containing 7.5 mg Isoleucine-Proline-Proline; IPP, MPH2 (each containing 6.6 mg Methionine-Alanine-Proline, 2.3 mg Leucine-Proline-Proline, 1.8 mg IPP, or placebo (containing cellulose for 4 weeks. Results In subjects with stage 1 hypertension, MPH1 lowered systolic BP by 3.8 mm Hg (P = 0.0080 and diastolic BP by 2.3 mm Hg (P = 0.0065 compared with placebo. In prehypertensive subjects, the differences in BP between MPH1 and placebo were not significant. MPH2 did not change BP significantly compared with placebo in stage I hypertensive or prehypertensive subjects. Intake of MPHs was well tolerated and safe. No treatment differences in hematology, clinical laboratory parameters or adverse effects were observed. No significant differences between MPHs and placebo were found in plasma renin activity, or angiotensin I and II. Conclusions MPH1, containing IPP and no minerals, exerts clinically relevant BP lowering effects in subjects with stage 1 hypertension. It may be included in lifestyle changes aiming to prevent or reduce high BP. Trial registration ClinicalTrials.gov NCT00471263

Photo-oxidative degradation of TiO{sub 2}/polypropylene films

Energy Technology Data Exchange (ETDEWEB)

García-Montelongo, X.L. [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Martínez-de la Cruz, A., E-mail: azael70@yahoo.com.mx [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Vázquez-Rodríguez, S. [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Torres-Martínez, Leticia M. [Facultad de Ingeniería Civil, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico)

2014-03-01

Graphical abstract: - Highlights: • Photo-oxidative degradation of polypropylene is accelerated by TiO{sub 2} incorporation. • Weight loss, FTIR, SEM and GPC shown high degree of degradation of polypropylene. • A mechanism of the photo-degradation of polypropylene by TiO{sub 2} is proposed. - Abstract: Photo-oxidative degradation of polypropylene films with TiO{sub 2} nanoparticles incorporated was studied in a chamber of weathering with Xenon lamps as irradiation source. TiO{sub 2} powder with crystalline structure of anatase was synthesized by thermal treatments at 400 and 500 °C starting from a precursor material obtained by sol–gel method. Composites of TiO{sub 2}/polypropylene were prepared with 0.1, 0.5 and 1.0 wt% of TiO{sub 2}. The mixture of components was performed using a twin screw extruder, the resulting material was pelletized by mechanical fragmenting and then hot-pressed in order to form polypropylene films with TiO{sub 2} dispersed homogeneously. Photo-oxidative degradation process was followed by visual inspection, weight loss of films, scanning electron microscopy (SEM), infrared spectroscopy with Fourier transformed (FTIR), and gel permeation chromatography (GPC)

Autoclaved Sand-Lime Products with a Polypropylene Mesh

Science.gov (United States)

Kostrzewa, Paulina; Stępień, Anna

2017-10-01

The paper presents the results of the research on modifications of silicate bricks with a polypropylene mesh and their influence on physical, mechanical and microstructural properties of such bricks. The main goal of the paper was to determine effects of the polypropylene mesh on sand-lime product parameters. The analysis has focused on compressive strength, water absorption, bulk density and structural features of the material. The obtained product is characterized by improved basic performance characteristics compared to traditional silicate products. Using the polypropylene mesh increased compressive strength by 25% while decreasing the product density. The modified products retain their form and do not disintegrate after losing their bearing capacity.

Microstructural evolution during tensile deformation of polypropylenes

International Nuclear Information System (INIS)

Dasari, A.; Rohrmann, J.; Misra, R.D.K.

2003-01-01

Tensile deformation processes occurring at varying strain rates in high and low crystallinity polypropylenes and ethylene-propylene di-block copolymers have been investigated by scanning electron microscopy. This is examined for both long and short chain polymeric materials. The deformation processes in different polymeric materials show striking dissimilarities in spite of the common propylene matrix. Additionally, the deformation behavior of long and their respective short chain polymers was different. Deformation mechanisms include crazing/tearing, wedging, ductile ploughing, fibrillation, and brittle fracture. The different modes of deformation are depicted in the form of strain rate-strain diagrams. At a constant strain rate, the strain to fracture follows the sequence: high crystallinity polypropylenes< low crystallinity polypropylenes< ethylene-propylene di-block copolymers, indicative of the trend in resistance to plastic deformation

Agave nonwovens in polypropylene composites: mechanical and thermal studies

CSIR Research Space (South Africa)

John, MJ

2015-03-01

Full Text Available Blends of agave fibres with wool waste, pineapple leaf fibres and polypropylene fibres were manufactured by needle-punching technique. Composites were prepared with polypropylene matrix by the process of compression moulding. The effects of blend...

Effect of ultraviolet radiation (300-400 nanometers) on polypropylene

International Nuclear Information System (INIS)

Lerman, S.

1983-01-01

Polypropylene discs and shavings were exposed to simulated ambient ultraviolet (UV) radiation (lambda 300-400 nm) for a period equivalent to at least two years of wear within the eye, assuming the eye to be exposed to ambient UV radiation for four hours per day at 1 mW/cm2. The polypropylene and the incubation media were measured by several forms of optical spectroscopy, and there was no photochemical change in either. Where polypropylene discs were exposed to a very high level of UV radiation (greater than 500 W/cm2), they became brittle and discolored within five to ten days. This level of exposure, however, was equivalent to a total of over 20 million joules/cm2, which is at least one million times levels for expected ambient UV exposure to polypropylene within the eye

Thermal and mechanical properties of polypropylene/titanium dioxide nanocomposite fibers

International Nuclear Information System (INIS)

Esthappan, Saisy Kudilil; Kuttappan, Suma Kumbamala; Joseph, Rani

2012-01-01

Highlights: ► Wet synthesis method was used for the synthesis of TiO 2 nano particles. ► Mechanical properties of polypropylene fibers were increased by the addition of TiO 2 nanoparticles. ► Thermal stability of polypropylene fiber was improved significantly by the addition of TiO 2 nano particles. ► TiO 2 nanoparticles dispersed well in polypropylene fibers. -- Abstract: Titanium dioxide nanoparticles were prepared by wet synthesis method and characterized by transmission electron microscopy and X-ray diffraction studies. The nanotitanium dioxide then used to prepare polypropylene/titanium dioxide composites by melt mixing method. It was then made into fibers by melt spinning and subsequent drawing. Mechanical properties of the fibers were studied using Favimat tensile testing machine with a load cell of 1200 cN capacity. Thermal behavior of the fibers was studied using differential scanning calorimetry and thermogravimetric analysis. Scanning electron microscope studies were used to investigate the titanium dioxide surface morphology and crosssection of the fiber. Mechanical properties of the polypropylene fiber was improved by the addition of titanium dioxide nanoparticles. Incorporation of nanoparticles improves the thermal stability of polypropylene. Differential scanning calorimetric studies revealed an improvement in crystallinity was observed by the addition of titanium dioxide nanoparticles.

Graft copolimerization of hydrophilic monomers onto irradiated polypropylene fibers

International Nuclear Information System (INIS)

Sundardi, F.

1978-01-01

A method of graft copolymerization of hydrophilic monomers, such as 1-vinyl-2-pyrrolidone, acrylonitrile, acrylic acid, and acrylamide, onto irradiated polypropylene fibers has been studied. γ ray as well as electron beam were employed for the irradiation processes. Graft-copolymerization kinetics and the properties of grafted fibers have been investigated. Moisture regain, dyes absorption, and melting point of the grafted fibers were found to increase with the increasing of the degree of grafting. Polypropylene for 1-vinyl-2-pyrrolidone grafted fibers showed excellent dye absorption for almost all kinds of dyes such as direct, basic, acid, reactive, disper, and naphthol dyes. However, for polypropylene acrylic acid grafted fibers, the colorfastness to washing was found to be unsatisfactory. The colorfastness to washing for polypropylene 1-vinyl-2-pyrrolidone grafted fibers was found to be fairly good for certain types of dyes such as vat and naphthol dyes. (author)

The effects of normal paraffins mobilizers on irradiated polypropylene

International Nuclear Information System (INIS)

Chen Wenxiu; Gao Ling

1995-01-01

The n-paraffins blended with polypropylene (PP) as mobilizer had been investigated. The effectiveness of mobilizer (n-paraffins) on irradiated polypropylene is dependent on the molecular weight of mobilizer and its content on polypropylene. The n-docosame (n-C 22 ) possesses the best effectiveness of radiation tolerance on PP among the mobilizer paraffins: n-decane (n-C 10 ), n-hexadecane (n-C 16 ), n-docosane (n-C 22 ) and n-hexatriacontane (n-C 36 ). The 2% (w/w) content of a given mobilizer is the most effective at reducing the embrittlement of irradiated PP as evidenced by the elongation at break. The physical properties of polypropylene with mobilizers such as density, Young's modulus, the Fraction of free volume and the weight swelling ratio in p-xylene at room temperature were measured. Above phenomena are related with the constructive of blended PP and demonstrated by its physical properties

Susceptibility to scratch surface damage of wollastonite- and talc-containing polypropylene micrometric composites

International Nuclear Information System (INIS)

Hadal, R.; Dasari, A.; Rohrmann, J.; Misra, R.D.K.

2004-01-01

The paper describes the effect of wollastonite and talc on the scratch deformation behavior of low and high crystallinity polypropylenes under identical test conditions. The vertical resolution of atomic force microscopy and lateral resolution of scanning electron microscopy is utilized to examine the characteristics of scratch damage. Contrary to the expectations that high crystallinity and stiffness of polypropylene composites should increase resistance to scratch deformation, the susceptibility to mechanical deformation depends on bonding of mineral particles to the polymer matrix. Scratch deformed regions in neat polypropylenes were free of voids and grooves, while reinforced-polypropylenes exhibited voids and debonding/detachment of filler particles. The severity of plastic deformation in reinforced polypropylenes is a function of debonding/detachment of mineral particles, which is comparatively more for talc-reinforced polypropylenes than wollastonite-reinforced polypropylenes because of the layered structure of talc that encourages delamination. Usage of coating and coupling agents improved the resistance to scratch deformation by promoting adhesion and bonding between the reinforcement and matrix

MRI and its role in the evaluation and surgical decision making in patients with challenging IPP presentations: descriptions of MRI findings and algorithm for patient management.

Science.gov (United States)

McPhail, E Fred; Nehra, Ajay; Bruner, Bryan C; Kawashima, Akira; King, Bernard F; Kim, Bohyun

2012-06-01

Study Type - Diagnostic (case series) Level of Evidence 4 What's known on the subject? and What does the study add? It is known that magnetic resonance imaging (MRI) is safe and effective for imaging patients with inflatable penile prostheses (IPPs). Previous series have reported results of MRI for imaging series of patients with IPPs. The impact on management in particular with regard to salvage procedures is not well defined. This study represents the largest known experience with MRI evaluation of IPPs. This also provides an algorithm that assists with decisions regarding utilization of MRI and treatment planning based on results. • In some patients who undergo placement of an inflatable penile prosthesis (IPP) the device may function inadequately. We describe the use of magnetic resonance imaging (MRI) for anatomical localization and detection of prosthesis malrotation, angulation, displacement and erosion in IPPs with equivocal clinical examination. • We prospectively performed MRI by a defined protocol including T1-weighted imaging, and transaxial, sagittal and coronal fat-saturated fast spin-echo T2-weighted imaging in both deflated and inflated states to evaluate patients seen at our referral centre for IPP-related complaints. • We retrospectively reviewed 32 such MRI studies performed as a supplement to clinical examination between 2000 and 2008. • Of 32 cases, 75% (24/32) underwent surgical intervention. Of these, 45% (11/24) underwent device salvage procedures including cylinder revision in 33% (8/24), cylinder replacement in 8% (2/24) and pump replacement in 4% (1/24). • MRI was most useful for determination of surgical approach in those with abnormal physical examination, and for justification of either surgical or expectant management in those with indeterminate physical examination. • MRI is safe and effective for imaging genitourinary prostheses. • We found MRI to be a valuable adjunct for evaluation of IPP-related complaints when

Polypropylene and polycarbonate radiosterilization: effects on the stress resistance

International Nuclear Information System (INIS)

Musico Filho, W.; Terence, M.C.; Guedes, S.M.L.; Araujo, E.S. de

1994-01-01

The gamma radiation effect on polymer sterilization used in the fabrication of medical supplies, national polycarbonate and polypropylene, was studied in function of the tensile strength. During the polycarbonate irradiation occur the scission of polymer chain and the crosslinking/scission of the polypropylene, but in the sterilization dose, 25 kGy, does not occur expressive changes in the tensile strength. After the polypropylene sterilization the tensile strength continues increasing as consequence of the crosslinking. Since the sixth day the oxidation reaction predominates as consequence of the radical migration to the amorphous region. (author). 7 refs, 6 figs

Polypropylene/graphite nanocomposites by in situ polymerization

International Nuclear Information System (INIS)

Milani, Marceo A.; Galland, Giselda B.; Quijada, Raul

2011-01-01

This work presents the synthesis of nanocomposites of polypropylene/graphite by in situ polymerization using metallocene catalyst and graphene nanosheets. Initially was analyzed which of the metallocene catalysts rac-Et(Ind) 2 ZrCl 2 or rac-Me 2 Si(Ind) 2 ZrCl 2 produces polypropylene with mechanical properties more relevant. Then it were performed the in situ polymerization reactions to obtain the nanocomposites. The polymeric materials were characterized by XRD, DSC, GPC and DMTA. (author)

Melt rheological properties of natural fiber-reinforced polypropylene

Science.gov (United States)

Jarrod J. Schemenauer; Tim A. Osswald; Anand R. Sanadi; Daniel F. Caulfield

2000-01-01

The melt viscosities and mechanical properties of 3 different natural fiber-polypropylene composites were investigated. Coir (coconut), jute, and kenaf fibers were compounded with polypropylene at 30% by weight content. A capillary rheometer was used to evaluate melt viscosity. The power-law model parameters are reported over a shear rate range between 100 to 1000 s–1...

Propylene

Directory of Open Access Journals (Sweden)

M. Emami

2007-08-01

Full Text Available This is a report on the study of high melt flow, highly isotactic polypropylene homopolymer synthesized in liquid monomer using a fifth generation Ziegler-Natta catalytic system. At highest catalyst productivity, the response of thecatalyst to hydrogen as chain transfer is studied. Melt flow rate is controlled by hydrogen as chain transfer from 0.4 to 300 g/10min with changing the amount of hydrogen from 0 to 1400 ppm. Results show that the melt flow rate of homopolymer is increased linearly with increasing the amount of hydrogen in polymerization. The effect of external electron donor on catalyst productivity and stereoregularity of the final product has been studied. The external electron donor on the catalyst caused an increase in polymer isotacticity, but led to decrease in catalyst productivity andits response to hydrogen (i.e., requiring relatively more hydrogen for molecular weight control. This new generation of Z-N catalyst system containing 1,3-diether as internal electron donor has the ability to produce very high MFR polymers (for thin wall parts in combination with narrow molecular weight distribution. These reactor grades of polypropylene have many advantages compared to visbroken (controlled rheology grades such as lower cost and better processability. These resins can be used as homopolymer matrix in sequential polymerization to obtain impactcopolymers (heterophasic copolymers.

Structure of single-chain single crystals of isotactic polystyrene and their radiation resistance

International Nuclear Information System (INIS)

Bu Haishan; Cao Jie; Xu Shengyong; Zhang Ze

1997-01-01

The structure of the single-chain single crystals of isotactic polystyrene (i-PS) was investigated by electron diffraction (ED) and high resolution electron microscopy (HREM). The nano-scale single-chain single crystals were found to be very stable to electron irradiation. According to the unit cell of i-PS crystals, the reflection rings in ED pattern and the lattice fringes in HREM images could be indexed, but the lower-index diffractions were not found. It is proposed that the single-chain single crystals are very small, thus secondary electrons may be allowed to escape and radiation damage is highly reduced, and that there are less lower-index lattice planes in the single-chain single crystals to provide sufficient diffraction intensity for recording. HREM images can be achieved at room temperature in the case of single-chain single crystals because of its stability to electron irradiation, therefore, this might be a novel experimental approach to the study of crystal structure of macromolecules

Comparison of polypropylene and silicone Ahmed Glaucoma Valves.

Science.gov (United States)

Ishida, Kyoko; Netland, Peter A; Costa, Vital P; Shiroma, Lineu; Khan, Baseer; Ahmed, Iqbal Ike K

2006-08-01

To evaluate and compare the clinical outcomes after implantation of the silicone plate and the polypropylene plate Ahmed Glaucoma Valves. Prospective, multicenter, comparative series. A total of 132 patients with uncontrolled glaucoma were treated with either the silicone or polypropylene Ahmed Glaucoma Valve implant. Success was defined according to 2 criteria: (1) intraocular pressure (IOP) of 6 mmHg or more or 21 mmHg or less, and (2) IOP reduction of at least 30% relative to preoperative values. Eyes requiring further glaucoma surgery, including cyclophotocoagulation, or showing loss of light perception were classified as failures. Average follow-up was 12.8 months (range, 6-30 months) for the silicone plate group and 14.5 months (range, 6-30 months) for the polypropylene plate group (P = 0.063). At the last follow-up examination, the mean IOP was 13.8+/-3.9 mmHg and 17.3+/-6.5 mmHg (PAhmed Glaucoma Valve (model FP7) showed improved IOP reduction compared with the polypropylene (model S2) implant. Differences observed in mean IOP, success rate, and complications suggest that plate material may influence clinical outcome.

POLYPROPYLENE-MODIFIED KAOLINITE COMPOSITES: EFFECT ...

African Journals Online (AJOL)

Meziane O, Bensedira A, Guessoum M and Haddaoui N

2016-05-01

May 1, 2016 ... prepared by the melt intercalation method. ... several beneficial variations on stiffness, hardness, toughness and heat ..... Polypropylene/ untreated and treated kaolinite composites have been prepared via direct melt.

Additive manufacturing with polypropylene microfibers.

Science.gov (United States)

Haigh, Jodie N; Dargaville, Tim R; Dalton, Paul D

2017-08-01

The additive manufacturing of small diameter polypropylene microfibers is described, achieved using a technique termed melt electrospinning writing. Sequential fiber layering, which is important for accurate three-dimensional fabrication, was achieved with the smallest fiber diameter of 16.4±0.2μm obtained. The collector speed, temperature and melt flow rate to the nozzle were optimized for quality and minimal fiber pulsing. Of particular importance to the success of this method is appropriate heating of the collector plate, so that the electrostatically drawn filament adheres during the direct-writing process. By demonstrating the direct-writing of polypropylene, new applications exploiting the favorable mechanical, stability and biocompatible properties of this polymer are envisaged. Copyright © 2017. Published by Elsevier B.V.

Radiation-induced grafting of acrylic acid onto polypropylene film and its biodegradability

Science.gov (United States)

Mandal, Dev K.; Bhunia, Haripada; Bajpai, Pramod K.; Chaudhari, C. V.; Dubey, K. A.; Varshney, L.

2016-06-01

Polypropylene based commodity polyolefins are widely used in packaging, manufacturing, electrical, pharmaceutical and other applications. The aim of the present work is to study the effect of grafting of acrylic acid on the biodegradability of acrylic acid grafted polypropylene. The effect of different conditions showed that grafting percentage increased with increase in monomer concentration, radiation dose and inhibitor concentration but decreased with increase in radiation dose rate. The maximum grafting of 159.4% could be achieved at optimum conditions. The structure of grafted polypropylene films at different degree of grafting was characterized by EDS, FTIR, TGA, DSC, SEM and XRD. EDS studies showed that the increase in acrylic acid grafting percentage increased the hydrophilicity of the grafted films. FTIR studies indicated the presence of acrylic acid on the surface of polypropylene film. TGA studies revealed that thermal stability decreased with increase in grafting percentage. DSC studies showed that melting temperature and crystallinity of the grafted polypropylene films lower than polypropylene film. SEM studies indicated that increase in acrylic acid grafting percentage increased the wrinkles in the grafted films. The maximum biodegradability could be achieved to 6.85% for 90.5% grafting. This suggested that microorganisms present in the compost could biodegrade acrylic acid grafted polypropylene.

Effect of nanosilica particles on polypropylene polymer modified asphalt mixture performance

Directory of Open Access Journals (Sweden)

Nura Bala

2018-06-01

Full Text Available The current study was conducted to investigate the effect of nanosilica particles on the performance characteristics of polymer modified asphalt binders. In this study, control 80/100 binder were modified with polypropylene polymer and nanosilica particles at concentration of 0%–4%. Both nanosilica particles and polypropylene polymer were added by weight of total bitumen content. The asphalt performance tests flexural four point beam fatigue test, indirect tensile strength, indirect tensile stiffness modulus and draindown tests are conducted to evaluate the effect of nanosilica particles. The results of the study shows that nanosilica particles improves the fatigue properties of polypropylene polymer modified binder. This indicates that nanosilica particles have significant effect on improving the performance properties of polymer modified binders. Also, the result reveals that thermoplastic polymer polypropylene with nanosilica particles when used as bitumen modifiers improve the performance and durability of asphalt mixtures. Keywords: Polypropylene, Fatigue cracking, Stiffness modulus, Modified asphalt, Draindown

Polypropylene Track Membranes for Mikro and Ultrafiltration of Chemically Aggressive Agents

CERN Document Server

Kravets, L I; Apel, P Yu

2000-01-01

A production process for track membranes on the basis of chemically resistant polymer polypropylene has been developed. Research in all stages of the formation of the polypropylene track membranes has been conducted: the main principles of the process of chemical etching of polypropylene irradiated with accelerated ions have been investigated, the most effective structure of the etchant for a selective etching of the heavy ion tracks has been selected, the parameters of etching have been optimized. A method for sensibilization of latent tracks in polypropylene by effect of solvents has been developed. It helps to reach a significant increase in etching selectivity. A method for destruction of an absorbed chromocontaining layer on the surface of polypropylene track membranes formed during etching has been elaborated. Experimental samples of the membranes for micro and ultrafiltration have been obtained and their properties have been studied in course of their exploitation in chemically aggressive agents. For t...

Development of Plasma Technologies at IPP NSC KIPT

International Nuclear Information System (INIS)

Tereshin, V.I.; Chebotarev, V.V.; Garkusha, I.E.; Lapshin, V.I.; Shvets, O.M.; Taran, V.S.

2001-01-01

Plasma Technologies in Institute of Plasma Physics of the NSC KIPT are recently developed in the following directions. Material surfaces modification under their irradiation with pulsed plasma streams of different working gases. Besides traditional analysis of improvements of tribological characteristics and structural-phase changes of the modified layers recently we started investigations of material corrosions characteristic improvement under influence of pulsed plasma on the material surfaces. As to the surface coatings in arc discharges of Bulat type devices, new trends are related with multi-layers coatings, using Ti-AI-N coatings in cutting tools, using high frequency discharges or combined HF- and arc discharges for increasing the nomenclature of goods to be coated. Development of ozonators is respectively new area for IPP NSC KIPT. On the base of barrier high-frequency discharge there were developed a number of high efficiency ozonators with ozone production up to 100 G/hour. (author)

Physical and dielectric properties of irradiated polypropylene and poly(ethylene terephthalate)

International Nuclear Information System (INIS)

Kita, H.; Okamoto, K.

1986-01-01

The effect of high-energy electron irradiation in air and in nitrogen on the physical and dielectric properties of polypropylene and poly(ethylene terephthalate) has been studied by measurements of electric strength, dielectric constant, dissipation factor, tensile strength, gel fraction and molecular weight distribution. Electric strength of polypropylene was improved by irradiation, while dielectric properties of poly(ethylene terephthalate) were virtually unaffected by irradiation of 1.0-20 Mrad. Possible mechanisms for increasing electric strength are discussed from the point of view of degradation and oxidation taking place simultaneously with crosslinking of polypropylene. The maximum dose level to improve the electric strength of polypropylene is determined to be about 5 Mrad. (author)

Co-60 gamma radiation assisted diffusion of iodine in polypropylene

Energy Technology Data Exchange (ETDEWEB)

Mathakari, N.L.; Bhoraskar, V.N. [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Pune, Maharashtra 411007 (India); Dhole, S.D., E-mail: sanjay@physics.unipune.ernet.i [Microtron Accelerator Laboratory, Department of Physics, University of Pune, Pune, Maharashtra 411007 (India)

2010-09-15

Thin films of polypropylene having dimensions 50 mm x 15 mm x 350 {mu}m were immersed in 1 N iodine solution and then irradiated with Co-60 gamma radiation for the periods of 48, 96 and 144 h at the doses varying from 14.4 to 43.2 kGy. The films were also kept immersed in iodine solution for similar periods but without irradiation. Furthermore, the films were also directly-irradiated with Co-60 gamma radiation for similar periods and doses. The radiation-iodinated, plain-iodinated and directly-irradiated samples were characterized by using various techniques such as weight gain EDS, SEM, FTIR, UV-visible spectroscopy, contact angle and XRD. Weight gain, EDS and SEM collectively reveal that gamma irradiation enhances iodine intake in polypropylene. FTIR, EDS and contact angle measurements indicate that presence of iodine during irradiation resists radiation induced carbonylation of polypropylene. FTIR also shows presence of HOI (Hypoiodous acid) species instead of expected C-I bonds. UV-visible analysis unambiguously shows that presence of iodine enhances radiation induced band gap reduction process of polypropylene. XRD indicates that iodine decreases the crystallinity of polypropylene.

The steps to forming a joint venture IPP in Poland

Energy Technology Data Exchange (ETDEWEB)

Allen, Z.; Colligan, M.J.

1998-07-01

Poland represents the largest market in Central Europe with 38 million people and an installed electrical generating capacity of about 32 gigawatts. Since 1989, when the process of governmental restructuring along free market principals began, the allure to IPP developers has been evident, but is of yet unrealized. The natural model for IPP development in Poland would seem to be joint ventures with Polish generating companies. These enterprises already have sites, franchises, and a going business to contribute to a joint company. There are a number of reasons why so few deals have been concluded in Poland to date, and a number of barriers still exist that tend to hamper the realization of project finance funded power joint ventures. But, these barriers are not insurmountable. Overcoming them in the context of a joint venture relationship with a domestic partner requires patience, work, and an ability to bridge the gaps between the realities of working in a post-Communist environment and the practicalities of structuring projects that can be financed in the international capital markets. The new Energy Law in Poland establishes a framework for a viable private sector power generation business. But the enabling regulations are yet to be published or approved. There is still effective political risk on account of the uncertainty this creates. Pressure is mounting on the Polish Government, especially due to its expressed interest in joining the EU, to get the power sector to operate on private sector terms, if not in private hands. The trends are pointing in the direction of increased market driven policies and practices. The conclusion is that, despite the delays of the past, independent power projects will start to happen in Poland on a joint venture basis, with increasing frequency in the next years.

A new constitutive model for prediction of impact rates response of polypropylene

Directory of Open Access Journals (Sweden)

Buckley C.P.

2012-08-01

Full Text Available This paper proposes a new constitutive model for predicting the impact rates response of polypropylene. Impact rates, as used here, refer to strain rates greater than 1000 1/s. The model is a physically based, three-dimensional constitutive model which incorporates the contributions of the amorphous, crystalline, pseudo-amorphous and entanglement networks to the constitutive response of polypropylene. The model mathematics is based on the well-known Glass-Rubber model originally developed for glassy polymers but the arguments have herein been extended to semi-crystalline polymers. In order to predict the impact rates behaviour of polypropylene, the model exploits the well-known framework of multiple processes yielding of polymers. This work argues that two dominant viscoelastic relaxation processes – the alpha- and beta-processes – can be associated with the yield responses of polypropylene observed at low-rate-dominant and impact-rates dominant loading regimes. Compression test data on polypropylene have been used to validate the model. The study has found that the model predicts quite well the experimentally observed nonlinear rate-dependent impact response of polypropylene.

Pulse NMR-spectroscopy of structural changes of chemically modified polypropylene

International Nuclear Information System (INIS)

Gafarov, A.M.; Galibeev, S.S.; Kochnev, A.M.; Sukhanov, P.P.; Arkhireev, V.P.

2004-01-01

The structure of polypropylene compositions is studied by the method of pulse NMR-spectroscopy. The polypropylene compositions are derived by means of the modification by multicomponent systems. The analysis of relaxation times in a wide temperature range is carried out. Character of changes going on at a level of supermolecular structures is described. It is shown that the amplifications that manifest themselves under the polypropylene modification by the mixtures based on 2,4-tolyilendiisocyanate and e-caprolactam, are related to the change in the intermolecular interaction and formation of a more ordered polymer structure. (authors)

Interfacial Effects on the Spherulitic Morphology of Isotactic Polystyrene Thin Films on Liquid Substrates

Directory of Open Access Journals (Sweden)

Takashi Sasaki

2016-01-01

Full Text Available The influence of interfaces on the morphology of flat spherulites of isotactic polystyrene (iPS grown in thin films on liquid substrates was investigated. Amorphous iPS thin films spin-cast from a solution were annealed for cold crystallization on glycerol and silicone oil (nonsolvents for iPS. The number density of grown spherulites was revealed to be higher on the glycerol substrate than on the silicone oil substrate. This implies that the primary nucleation rate of crystallization is greater at the iPS/glycerol interface than at the iPS/silicone oil interface. The results may be consistent with the previous findings that concern the molecular interaction between atactic polystyrene and nonsolvents at the interface. In some cases, holes were formed in the thin films during the cold crystallization due to dewetting, which also significantly affect the spherulite morphology via, for example, transcrystallization.

Nucleation of polypropylene crystallization with gold nanoparticles. Part 2: relation between particle morphology and nucleation activity

Czech Academy of Sciences Publication Activity Database

Šlouf, Miroslav; Vacková, Taťana; Zhigunov, Alexander; Sikora, Antonín; Piorkowska, E.

2016-01-01

Roč. 55, č. 4 (2016), s. 393-410 ISSN 0022-2348 R&D Projects: GA ČR GAP205/10/0348; GA ČR(CZ) GA14-17921S Institutional support: RVO:61389013 Keywords : crystallization * gold nanoparticles * isotactic polyproplylene Subject RIV: JJ - Other Materials Impact factor: 0.828, year: 2016

Thermal degradation kinetics and estimation of lifetime of radiation grafted polypropylene films

International Nuclear Information System (INIS)

Mandal, Dev K.; Bhunia, Haripada; Bajpai, Pramod K.; Bhalla, Vinod Kumar

2017-01-01

In this research work, thermal stability and degradation behavior of acrylic acid grafted polypropylene (PP-g-PAAc) films were investigated by using thermogravimetric (TGA) analysis at four different heating rates 5, 10, 15 and 20 °C/min over a temperature range of 40–550 °C in nitrogen atmosphere. The kinetic parameters namely activation energy (E a ), reaction order (n) and frequency factor (Z) were calculated by three multiple heating rate methods. The thermal stability of PP-g-PAAc films is found to decrease with increase in degree of grafting. The TGA data and thermal kinetic parameters were also used to predict the lifetime of grafted PP films. The estimated lifetime of neat PP as well as grafted PP decreased with increase in temperature by all the three methods. Studies also indicated that E a and lifetime of PP-g-PAAc films decreased with increase in degree of grafting, which may also be helpful in biodegradation of grafted PP films. - Highlights: • Thermal stability of grafted polypropylene films have been observed lower than for neat polypropylene film. • Multiple heating rate methods have been used for determination of activation energy. • Activation energies of grafted polypropylene films were lower than polypropylene film. • The lifetimes of grafted polypropylene films were shorter than for neat polypropylene film.

Determination of Partition Coefficients of Selected Model Migrants between Polyethylene and Polypropylene and Nanocomposite Polypropylene

Directory of Open Access Journals (Sweden)

Pablo Otero-Pazos

2016-01-01

Full Text Available Studies on nanoparticles have focused the attention of the researchers because they can produce nanocomposites that exhibit unexpected hybrid properties. Polymeric materials are commonly used in food packaging, but from the standpoint of food safety, one of the main concerns on the use of these materials is the potential migration of low molecular substances from the packaging into the food. The key parameters of this phenomenon are the diffusion and partition coefficients. Studies on migration from food packaging with nanomaterials are very scarce. This study is focused on the determination of partition coefficients of different model migrants between the low-density polyethylene (LDPE and polypropylene (PP and between LDPE and nanocomposite polypropylene (naPP. The results show that the incorporation of nanoparticles in polypropylene increases the mass transport of model migrants from LDPE to naPP. This quantity of migrants absorbed into PP and naPP depends partially on the nature of the polymer and slightly on the chemical features of the migrant. Relation (RPP/naPP between partition coefficient KLDPE/PP and partition coefficient KLDPE/naPP at 60°C and 80°C shows that only BHT at 60°C has a RPP/naPP less than 1. On the other hand, bisphenol A has the highest RPP/naPP with approximately 50 times more.

Theoretical calculations of the reaction cross-sections for proton-induced reactions on natural copper using ALICE-IPPE code

International Nuclear Information System (INIS)

Alharbi, A.A.; Azzam, A.

2012-01-01

A theoretical study of the nuclear-reaction cross sections for proton-induced reactions on 63 Cu and 65 Cu was performed in the proton energy range from threshold values up to 50 MeV. The produced nuclei were different isotopes of Zn, Cu, Ni, Co and Mn, some of which have important applications. The reaction cross-section calculations were performed using the ALICE-IPPE code, which depends on the pre-equilibrium compound nucleus model. This code is suitable for the studied energy and isotopic mass ranges. Approximately 14 excitation functions for the different reactions have been constructed from the calculated cross-section values. The excitation function curves for the proton reactions with natural copper targets have been constructed from those for enriched targets using the natural abundance of the copper isotopes. Comparisons between the calculated excitation functions with those previously experimentally measured are given whenever the experimental values were available. Some statistical parameters were introduced to control the quality of the fitting between both the experimental and the theoretical calculated cross-section values. - Highlights: ► We performed reaction cross section calculations using ALICE-IPPE code. ► We constructed 14 excitation functions for nat Cu(p,xn)Zn,Cu,Ni,Co,Mn reactions. ► The available experimental data were fitted to the performed ALICE-IPPE calculations. ► Statistical parameters were introduced to control the quality of the fitting. ► The code failed to fit the experimental data for reactions with large nucleon emissions.

THE FTIR STUDIES OF PHOTO-OXIDATIVE DEGRADATION OF POLYPROPYLENE

Institute of Scientific and Technical Information of China (English)

WEN Zaiqing; HU Xingzhou; SHEN Deyan

1988-01-01

The photo-oxidative degradation process of polypropylene film containing iron ions was investigated via FTIR and absorbance substraction technique. It is shown that the iron ions play an important role in the decomposition of hydroperoxide and the increase of the degradation rate of polypropylene film. Theamorphous region of PP film undergoes degradation prior to the crystalline one.

Radiation resistant modified polypropylene; Polipropylen modyfikowany odporny radiacyjnie

Energy Technology Data Exchange (ETDEWEB)

Bojarski, J; Zimek, Z [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

1997-10-01

Radiation technology for production of radiation resistant polypropylene for medical use has been presented. The method consists in radiation induced copolymerization of polypropylene with ethylene and addition of small amount of copolymer of polyethylene and vinyl acetate. The material of proposed composition has a very good mechanical properties and elevated radiation resistivity decided on possibility of radiosterilization of products made of this material and designed for medical use. 3 figs, 3 tabs.

Application to refrigerator plastics by mechanical recycling from polypropylene in waste-appliances

International Nuclear Information System (INIS)

Ha, Kyung Ho; Kim, Moon Saeng

2012-01-01

Highlights: → Polypropylene is mechanically recycled from waste-appliances. → Recycled polypropylene (RPP) is impact enhanced polypropylene with ethylene-propylene rubber (EPR). → Performance evaluation shows that RPP is applicable to refrigerator plastics. -- Abstract: For the application to refrigerator plastics by mechanical recycling from polypropylene (PP) in waste-appliances, it needs to identify the degradation and heterogeneity of recycled polypropylene (RPP). It is applicable the thermal analysis such as differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), spectroscopic analysis such as Fourier Transform Infrared (FTIR) and morphological analysis such as scanning electronic microscope (SEM). The analysis results show that RPP from waste-appliances is the polyethylene (PE) and polypropylene (PP) copolymer enhanced impact property (Impact-PP) and it is possible to apply refrigerator plastics with good impact property at low temperature. Finally, the performance evaluation of RPP is estimated by Gel Permeation Chromatography (GPC) analysis and is performed by the various mechanical and physical testing methods. It shows that RPP has relatively high molecular weight and balanced properties with strength and toughness. It is expected that RPP by the mechanical recycling from waste-appliances will have about 50% cost-merit.

Rheological properties of polypropylene nanocomposites

International Nuclear Information System (INIS)

Oliveira, Camila F. de P.; Demarquette, Nicole R.

2009-01-01

In this work, composites of polypropylene with a master batch to obtain clay containing nano composites were obtained. The materials were characterized by X ray diffraction, small angle X-ray scattering and by rheological analysis. (author)

Woodflour as Reinforcement of Polypropylene

Directory of Open Access Journals (Sweden)

José Cláudio Caraschi

2002-10-01

Full Text Available The effect of the filler content and size, as well as accelerated aging on the mechanical properties of polypropylene composites reinforced with woodflour (WF/PP were evaluated. The composites were prepared by the extrusion of polypropylene with woodflour (Pinus elliotti based on following ratios: 15, 25 and 40 wt% with two different granulometries. The specimens were injection molded according to ASTM standards. The composite properties did not show significant differences as a function of the filler granulometry. We also observed that by increasing the filler content, both the mechanical properties and the melt flow index (MFI decreased, and the elasticity modulus, hardness and density increased. Concerning the accelerated aging, the composite presented a reduction in tensile properties. The results showed that the composite properties are extremely favorable when compared to other commercial systems reinforced by inorganic fillers.

Modification of polypropylene with radiation-treated wood fiber

International Nuclear Information System (INIS)

Czvikovszky, T.; Tapolcai, I.

1983-01-01

The dispersed wood material is used not only as filler for thermosetting polymers but also as a new type of fibrous additive for thermoplastics e.g. polypropylene. Benefit of this additive (filler or reinforcement) is determined by the coupling between the wood and the synthetic resin. Fibrous, dispersed wood material was preirradiated in air, treated with vinyl monomer containing polyester resin and then mixed in polypropylene. Processability of such thermoplastic blends as well as reactivity of the mixed components were followed by measuring energy, absorbed during the kneading of the melt. The vinylmonomer vinylmonomer - polyester additive, activated at higher temperature by the radiation-formed peroxy groups on the wood fiber, results in good processability of the thermoplastic blend, and gives interesting mechanical properties. Calandering, extrusion, pressmoulding and mechanical testing demonstrated good workability and practical value of the polypropylene composite material containing radiation-treated wood fiber. (author)

Improvement of radiation resistance of polypropylene by blending with polyethylene and polystyrene

International Nuclear Information System (INIS)

Al Aji, Z.

2001-01-01

The use of polypropylene in production of medical component and packaging materials makes it an interesting material for applied research. Since the use of ethylene oxide for sterilization of medical components will be forbidden in the next future because of its carcinogens effect. Therefore, another alternative sterilization methods are required. The use of Gamma radiation is already established for sterilization of some medical components, this technique causes change in the physical mechanical properties of polypropylene, which makes the addition of stabilizers necessary. In this work, blends of domestically used polymers, polypropylene, linear low-density polyethylene, and polystyrene/butadiene were prepared in order to improve the radiation resistance of polypropylene; naphthalene was also used as an additive

Radiation-modified blends of the basis of polyethylene terephthalate and polypropylene

International Nuclear Information System (INIS)

Mery-Meri, R.; Revyakin, O.; Zicans, J.

2000-01-01

The binary composite systems on the basis of post-consumer poly-(ethylene terephthalate) and polypropylene have been investigated. Mechanical properties of the compositions were studied in detail in order to expand the application possibilities of tested binary composites. Structural changes of the poly (ethylene terephthalate) / polypropylene blends depending on the concentration of the components were investigated also. Additionally, the optimum processing conditions were established. Particular attention was paid to study the influence of the ionizing γ-radiation on the structural and mechanical properties of the composition systems tested. The magnitude of the adsorbed dose od γ-radiation was established to affect differently the structure of poly(ethylene terephalate) and polypropylene. At small absorbed doses (50 kGy) crosslinking of the polymer was observed for both poly(ethylene terephthalate) and polypropylene resulting in the increase of some mechanical properties of pure materials as well of their compositions, whereas the absorbed dose of 300 kGy caused the destruction of the tested materials. It is important to mention that the rate of radiation-chemical destruction of polypropylene is higher than poly(ethylene terephthalate) destruction rate. (author)

Morphological, viscoelastic and mechanical characterization of polypropylene/exfoliated graphite nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Creusa Iara; Oliveira, Ricardo Vinicius Bof de; Mauler, Raquel Santos, E-mail: raquel.mauler@ufrgs.br [Universidade Federal do Rio Grande do Sul (PGCIMAT/IQ/UFRGS), Porto Alegre, RS (Brazil); Bianchi, Otavio [Universidade de Caxias do Sul (PGMAT/CCET/UCS), RS (Brazil); Oviedo, Mauro Alfredo Soto [Braskem S/A, Rio de Janeiro, RJ (Brazil)

2013-07-01

The viscoelastic, mechanical and morphological properties of polypropylene/exfoliated graphite nanocomposites with different contents of nanofiller were investigated. According to transmission electron microscopy results, the nanofiller particles were homogeneously dispersed in the matrix. The rheological properties indicated that incorporation of graphite improved the matrix stiffness and had a reinforcing effect. Exfoliated graphite had a weak interaction with the polypropylene. The behavior of the nanocomposites was similar to that of polypropylene in terms of the interfacial detachment inferred from the transmission electron microscopy images and of their G' (storage) and G' (loss) moduli, and viscosity. The mechanical properties of the nanocomposites compared to the matrix improved significantly for the flexural and storage moduli with little loss of impact strength. (author)

High strain rate behaviour of polypropylene microfoams

Science.gov (United States)

Gómez-del Río, T.; Garrido, M. A.; Rodríguez, J.; Arencón, D.; Martínez, A. B.

2012-08-01

Microcellular materials such as polypropylene foams are often used in protective applications and passive safety for packaging (electronic components, aeronautical structures, food, etc.) or personal safety (helmets, knee-pads, etc.). In such applications the foams which are used are often designed to absorb the maximum energy and are generally subjected to severe loadings involving high strain rates. The manufacture process to obtain polymeric microcellular foams is based on the polymer saturation with a supercritical gas, at high temperature and pressure. This method presents several advantages over the conventional injection moulding techniques which make it industrially feasible. However, the effect of processing conditions such as blowing agent, concentration and microfoaming time and/or temperature on the microstructure of the resulting microcellular polymer (density, cell size and geometry) is not yet set up. The compressive mechanical behaviour of several microcellular polypropylene foams has been investigated over a wide range of strain rates (0.001 to 3000 s-1) in order to show the effects of the processing parameters and strain rate on the mechanical properties. High strain rate tests were performed using a Split Hopkinson Pressure Bar apparatus (SHPB). Polypropylene and polyethylene-ethylene block copolymer foams of various densities were considered.

Antioxidant action in irradiated polypropylene studied by ultraviolet spectroscopy

International Nuclear Information System (INIS)

Milosavljevic, B.H.; Novakovic, Lj.

1999-01-01

Ultraviolet spectrum of 0.2 mm thick film of polypropylene containing 0.5% ORGANOX 1010 showed that in the sample prepared by slow cooling about 15% of the antioxidant reacted during the preparation process. The difference in turbidity between the samples obtained in the slow and the fast cooling process is attributed to the degree of crystallinity, which is in agreement with the DSC data. Very pronounced effects of the oxygen concentration and the degree of crystallinity on antioxidant uptake in irradiated polypropylene films were observed and discussed. It was also shown that a Febetron 707 pulsed electron accelerator is capable of producing both the single pulse dose (50 kGy) and the dose rate (2.5 TGy/s) large enough to enable a comparison of dose rate effects and LET effects in the study of the antioxidant reactions in polypropylene

Production of the oxidation-resistant polypropylene track membranes

International Nuclear Information System (INIS)

Kravets, L.I.; Dmitriev, S.N.; Apel, P.Y.

1999-01-01

This paper describes results of the method of manufacturing the polypropylene track membranes produced by physicochemical treatment under irradiation of accelerated heavy ions of polymer films. The developed method allows to produce membranes 0.1 - 0.2 μm in diameter and more with an improved structural and physicochemical properties. Poly-propylene track membranes of a novel sample are characterized by high homogeneity of pore sizes in magnitude, considerable mechanical strength, advanced thermal stability and resistance to oxidation in aggressive media. It opens new fields for their usage

Preparation of organophilic clays and polypropylene nano composites

International Nuclear Information System (INIS)

Lima, Martha Fogliato S.; Nascimento, Vinicius G. do; Lenz, Denise M.; Schenato, Flavia

2011-01-01

Polypropylene/montmorillonite nano composites were prepared by the melt intercalation technique. The clay was organically modified with different quaternary ammonium salts to obtain the organo clay. The modified clays with the quaternary ammonium salts were introduced in a polypropylene matrix with 3 wt. % of clay. The interlayer distance (d001) of the clay particles were obtained by X- ray diffraction and the thermal stability of the systems were investigated by thermogravimetry. The organo clay presence in the polymer matrix increased the degradation temperature in relation to the pure polymer. (author)

Morphological, viscoelastic and mechanical characterization of polypropylene/exfoliated graphite nanocomposites

Directory of Open Access Journals (Sweden)

Creusa Iara Ferreira

2013-01-01

Full Text Available The viscoelastic, mechanical and morphological properties of polypropylene/exfoliated graphite nanocomposites with different contents of nanofiller were investigated. According to transmission electron microscopy results, the nanofiller particles were homogeneously dispersed in the matrix. The rheological properties indicated that incorporation of graphite improved the matrix stiffness and had a reinforcing effect. Exfoliated graphite had a weak interaction with the polypropylene. The behavior of the nanocomposites was similar to that of polypropylene in terms of the interfacial detachment inferred from the transmission electron microscopy images and of their G' (storage and G'' (loss moduli, and viscosity. The mechanical properties of the nanocomposites compared to the matrix improved significantly for the flexural and storage moduli with little loss of impact strength.

Morphological, viscoelastic and mechanical characterization of polypropylene/exfoliated graphite nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Creusa Iara; Oliveira, Ricardo Vinicius Bof de; Mauler, Raquel Santos, E-mail: raquel.mauler@ufrgs.br [Universidade Federal do Rio Grande do Sul (PGCIMAT/IQ/UFRGS), Porto Alegre, RS (Brazil); Bianchi, Otavio [Universidade de Caxias do Sul (PGMAT/CCET/UCS), RS (Brazil); Oviedo, Mauro Alfredo Soto [Braskem S/A, Rio de Janeiro, RJ (Brazil)

2013-07-01

The viscoelastic, mechanical and morphological properties of polypropylene/exfoliated graphite nanocomposites with different contents of nanofiller were investigated. According to transmission electron microscopy results, the nanofiller particles were homogeneously dispersed in the matrix. The rheological properties indicated that incorporation of graphite improved the matrix stiffness and had a reinforcing effect. Exfoliated graphite had a weak interaction with the polypropylene. The behavior of the nanocomposites was similar to that of polypropylene in terms of the interfacial detachment inferred from the transmission electron microscopy images and of their G' (storage) and G' (loss) moduli, and viscosity. The mechanical properties of the nanocomposites compared to the matrix improved significantly for the flexural and storage moduli with little loss of impact strength. (author)

High-voltage pulsed life of multistressed polypropylene capacitor dielectric

International Nuclear Information System (INIS)

Laghari, J.R.

1992-01-01

High-voltage polypropylene capacitors were aged under singular as well as simultaneous multiple stresses (electrical, thermal, and radiation) at the University of Buffalo's 2 MW thermal nuclear reactor. These stresses were combined neutron-gamma radiation with a total dose of 1.6 x 10 6 rad, electrical stress at 40 V rms /μm, and thermal stress at 90 degrees C. After exposure, the polypropylene dielectric was tested for life (number of pulses to fail) under high-voltage high-repetition-rate (100 pps) pulses. Pulsed life data were also compared with ac life data. Results show that radiation stress causes the most degradation in life, either acting alone or in combination with other stresses. The largest reduction in life occurs when polypropylene is aged under simultaneous multiple stresses (electrical, thermal, and radiation). In this paper, it is shown that pulsed life can be equivalently compared with ac life

PLASTIC SHRINKAGE CONTROLLING EFFECT BY POLYPROPYLENE SHORT FIBER WITH HYDROPHILY

Science.gov (United States)

Hosoda, Akira; Sadatsuki, Yoshitomo; Oshima, Akihiro; Ishii, Akina; Tsubaki, Tatsuya

The aim of this research is to clarify the mechanism of controlling plastic shrinkage crack by adding small amout of synthetic short fiber, and to propose optimum polypropylene short fiber to control plastic shrinkage crack. In this research, the effect of the hydrophily of polypropylene fiber was investigated in the amount of plastic shrinkage of mortar, total area of plastic shrinkage crack, and bond properties between fiber and mortar. The plastic shrinkage test of morar was conducted under high temperature, low relative humidity, and constant wind velocity. When polypropylene fiber had hydrophily, the amount of plastic shrinkage of mortar was restrained, which was because cement paste in morar was captured by hydrophilic fiber and then bleeding of mortar was restrained. With hydrophily, plastic shrinkage of mortar was restrained and bridging effect was improved due to better bond, which led to remarkable reduction of plastic shrinkage crack. Based on experimental results, the way of developing optimum polypropylene short fiber for actual construction was proposed. The fiber should have large hydrophily and small diameter, and should be used in as small amount as possible in order not to disturb workability of concrete.

Fiscal 1997 survey of overseas coal import base arrangement and promotion. Effects of the expansion of coal trade by IPP on the supply/demand of general coal in Asia; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. IPP ni yoru sekitan boeki no kakudai ga Asia no ippantan jukyu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In consideration of the coal situation in the Asia/Pacific region, a study was made of effects of the expansion of coal trade by IPP on supply/demand of general coal in Asia. When aggregating increases in demand of general coal for electric power use in ten Asian counties, they will be an increase of 130.75 million tons in 2005 over 1997. Fifty nine percent of it is equivalent to the increase by IPP and exceeds the demand expanded by electric utilities operators. Further, a possibility is predicted of contracts and coal quality being different from until now. However, there will be a lot of cases in which plans of constructing power plants in Asia are not so developed as expected except Japan, Korea and Taiwan, and also the effect of the currency crisis starting in Thailand largely affects. In terms of the coal supply, countries which export general coal are only China and Indonesia. Indonesian coal is expanding its production and export rapidly and remarkably. The environmental control in Asia has been tightening, and the fuel selected by IPP is mainly coal rather than natural gas. 40 refs., 94 figs., 179 tabs.

High strain rate behaviour of polypropylene microfoams

Directory of Open Access Journals (Sweden)

Martínez A.B.

2012-08-01

Full Text Available Microcellular materials such as polypropylene foams are often used in protective applications and passive safety for packaging (electronic components, aeronautical structures, food, etc. or personal safety (helmets, knee-pads, etc.. In such applications the foams which are used are often designed to absorb the maximum energy and are generally subjected to severe loadings involving high strain rates. The manufacture process to obtain polymeric microcellular foams is based on the polymer saturation with a supercritical gas, at high temperature and pressure. This method presents several advantages over the conventional injection moulding techniques which make it industrially feasible. However, the effect of processing conditions such as blowing agent, concentration and microfoaming time and/or temperature on the microstructure of the resulting microcellular polymer (density, cell size and geometry is not yet set up. The compressive mechanical behaviour of several microcellular polypropylene foams has been investigated over a wide range of strain rates (0.001 to 3000 s−1 in order to show the effects of the processing parameters and strain rate on the mechanical properties. High strain rate tests were performed using a Split Hopkinson Pressure Bar apparatus (SHPB. Polypropylene and polyethylene-ethylene block copolymer foams of various densities were considered.

Stabilization of polypropylene, polypropylene blends with poly (styrene-b-(ethylene-co-butylene)-b-styrene) under irradiation: A comparative investigation

International Nuclear Information System (INIS)

Luan Shifang; Yang Huawei; Shi Hengchong; Zhao Jie; Wang Jianwei; Yin Jinghua

2011-01-01

The aim of this paper is to investigate the stabilization of polypropylene in the poly (styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS)/polypropylene (PP) blends under irradiation with respect to PP. The PP films, SEBS/PP films were subjected to electron beam irradiation and characterized by wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), and dynamic mechanical thermal analysis (DMTA). It demonstrated that upon irradiation, the molecular weight of PP had a pronounced decrease due to the major chain scission, and the minor chain cross-linking or chain branching occurred at the higher irradiation dose. Stabilization of PP was improved in the presence of SEBS, exhibiting an enhanced irradiation resistance.

Stabilization of polypropylene, polypropylene blends with poly (styrene-b-(ethylene-co-butylene)-b-styrene) under irradiation: A comparative investigation

Energy Technology Data Exchange (ETDEWEB)

Luan Shifang; Yang Huawei; Shi Hengchong; Zhao Jie [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Wang Jianwei [Shandong Weigao Group Medical Polymer Company Limited, Weihai 264209 (China); Yin Jinghua, E-mail: yinjh@ciac.jl.c [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2011-01-15

The aim of this paper is to investigate the stabilization of polypropylene in the poly (styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS)/polypropylene (PP) blends under irradiation with respect to PP. The PP films, SEBS/PP films were subjected to electron beam irradiation and characterized by wide angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), and dynamic mechanical thermal analysis (DMTA). It demonstrated that upon irradiation, the molecular weight of PP had a pronounced decrease due to the major chain scission, and the minor chain cross-linking or chain branching occurred at the higher irradiation dose. Stabilization of PP was improved in the presence of SEBS, exhibiting an enhanced irradiation resistance.

The effect of modified ijuk fibers to crystallinity of polypropylene composite

Science.gov (United States)

Prabowo, I.; Nur Pratama, J.; Chalid, M.

2017-07-01

Nowadays, plastics becomes concern associated with its degradation and environmental issues. It has led studies to develop an environmental-friendly material. To minimize the impact of those problems, recently the usage of natural fibers as a filler are introduced because of biodegradability and availability. The promising natural fiber is “ijuk” fiber from Arenga pinnata plant as a filler and polypropylene (PP) polymer as a matrix. Unfortunately, the natural fibers and polymers have the different properties on which polymers are polar while natural fibers are non-polar so that reducing the compatibility and resulting the poor crystallinity. To enhance the compatibility and crystallinity, ijuk fibers were prepared by multistage treatments including alkalinization with 5 and 10% sodium hydroxide (NaOH), oxidation with 3 and 6% sodium hypochlorite (NaClO) and hydrolysis with 20% sulphuric acid (H2SO4) in sequences. The purposes of multistage treatments are to remove the components such as lignin, wax, hemicellulose, to cause an oxidative fragmentation of remaining lignin and to annihilate the amorphous parts respectively. Fourier-Transform Infrared (FTIR) confirms the compatibility meanwhile Differential Scanning Calorimetry (DSC) reveals the crystallinity and Scanning Electron Microscope (SEM) displays surface morphology of polypropylene. The experiments were revealing that the effects of “ijuk” fibers by the multistage treatments of 5 and 10% NaOH resulting the crystallinity of polypropylene around 31.2 and 27.64% respectively compared to the crystallinity before adding the “ijuk” fibers for 16.8%. It indicates that the entire treatments increasing the compatibility and crystallinity of polypropylene. In addition, the use of 5% NaOH offers the better crystallinity than non-treated polypropylene. The experiments conclude that by adding alkalinized “ijuk” fibers of multistage treatments can increase the compatibility and crystallinity of polypropylene.

Assessment on the Effects of ZnO and Coated ZnO Particles on iPP and PLA Properties for Application in Food Packaging

Directory of Open Access Journals (Sweden)

Antonella Marra

2017-02-01

Full Text Available This paper compares the properties of iPP based composites and PLA based biocomposites using 5% of ZnO particles or ZnO particles coated with stearic acid as filler. In particular, the effect of coating on the UV stability, thermostability, mechanical, barrier, and antibacterial properties of the polymer matrix were compared and related to the dispersion and distribution of the loads in the polymer matrix and the strength of the adhesion between the matrix and the particles. This survey demonstrated that, among the reported systems, iPP/5%ZnOc and PLA/5%ZnO films are the most suitable active materials for potential application in the active food packaging field.

Application of gas chromatography to the investigations on polypropylene radiolysis

International Nuclear Information System (INIS)

Zagorski, Z.P.; Gluszewski, W.

2006-01-01

Refinement of the gas chromatography (GC) instrumental approach permitted not only improvement of investigation in basic research, but also development of a new kind of polypropylene blends, more suitable for the production of medical devices and radiation sterilization. It has been shown, that using the GC method not only methane and carbon dioxide can be measured, but also the consumption of oxygen which reacts with free radicals on the polypropylene chain

High impact strength polymers having novel nano-structures produced via reactive extrusion

Science.gov (United States)

Tortorella, Nathan Fraser

A major focus of scientists and engineers over the last century has been to increase the impact strength and therefore reduce the brittleness of materials. By altering and adding energy absorption mechanisms, brittle failure can be averted. Isotactic polypropylene (PP) is the focus of this dissertation because it is an extremely low cost, high volume, versatile plastic but behaves in a brittle manner at or below room temperature or in a notched state. Early work on impact modification of polypropylene focused on blending energy-absorbing low density elastomers and rubbers. These binary blends all had a common problem---an increase in impact strength was paralleled by a significant decrease in both elastic modulus and yield stress. Reactive extrusion processing has allowed the in-situ compatibilization of isotactic polypropylene and metallocene-catalyzed ethylene-octene copolymers (EOCs). This process involves combining both the comonomer and vector fluid approaches to grafting polyolefins. Styrene monomer and a multifunctional acrylate monomer undergo peroxide-induced copolymerization and grafting in the presence of both PP and EOC. This results in a phase separated alloy with an impact strength over 13 times that of pure polypropylene and double that of the physical blend. There is also a significant improvement in stress-strain performance when comparing the alloys to physical blend counterparts. Many researchers have categorized the necessary components to toughening polypropylene as pertaining to the amorphous phase. The alloys described in this dissertation meet the criteria put forth by these researchers, namely low density, crystallinity, and modulus of the elastomer phase, sub-micron particle diameter, close inter-particle distance, and a high degree of entanglements of both the PP matrix phase and EOC minor phase. But many people neglect to study the crystalline state of impact modified PP in conjunction with the amorphous phase. This work shows that the

Anomalous behavior of secondary dielectric relaxation in polypropylene glycols

Energy Technology Data Exchange (ETDEWEB)

Grzybowska, K; Grzybowski, A; Ziolo, J; Rzoska, S J; Paluch, M [Institute of Physics, Silesian University, Uniwersytecka 4, 40-007 Katowice (Poland)

2007-09-19

A surprising slow down in the dielectric secondary {gamma}-relaxation with temperature increasing near the glass transition is confirmed for several polypropylene glycols. The peculiar behavior diminishes as the molecular weight grows. The minimal model (Dyre and Olsen 2003 Phys. Rev. Lett. 91 155703) is applied successfully to describe the temperature dependences of the {gamma}-relaxation times. The minimal model parameters are analyzed for different molecular weights. A molecular explanation of the {gamma}-process anomaly for polypropylene glycols is proposed on the basis of the minimal model prediction.

Isospecific propylene polymerization with in situ generated bis(phenoxy-amine)zirconium and hafnium single site catalysts.

Science.gov (United States)

Makio, Haruyuki; Prasad, Aitha Vishwa; Terao, Hiroshi; Saito, Junji; Fujita, Terunori

2013-07-07

Bis(phenoxy-imine) Zr and Hf complexes were activated with (i)Bu3Al or (i)Bu2AlH in conjunction with Ph3CB(C6F5)4 and tested as catalysts for propylene polymerization with emphasis on the enantioselectivity of the isospecific species and the single site polymerization characteristics. The isoselective species was identified as the in situ generated bis(phenoxy-amine) complex whose isoselectivity was sensitive to subtle changes in ligand structure. By employing specific substituents at certain key positions the isotacticity reached an extremely high level comparable to high-end commercial isotactic polypropylenes (Tm > 160 °C). Single site polymerization characteristics depended upon the efficiency and selectivity of the in situ imine reduction which is sensitive to the substituent on the imine nitrogen and the reaction conditions. By using (i)Bu2AlH as a reducing agent, quantitative imine reduction can be achieved with a stoichiometric amount of the reducing agent. This lower alkylaluminum loading is beneficial for the catalyst and significantly enhances the polymerization activity and the molecular weight of the resultant polymer.

Mechanism of isotactic styrene polymerization with a C 6F 5-substituted bis(phenoxyimine) titanium system

KAUST Repository

Caporaso, Lucia; Loria, Marianna; Mazzeo, Mina; Michiue, Kenji; Nakano, Takashi; Fujita, Terunori; Cavallo, Luigi

2012-01-01

We report a combined, experimental and theoretical, study of styrene polymerization to clarify the regio- and stereocontrol mechanism operating with a C 6F 5-substituted bis(phenoxyimine) titanium dichloride complex. Styrene homopolymerization, styrene-propene and styrene-ethene-propene copolymerizations have been carried out to this aim. A combination of 13C NMR analysis of the chain-end groups and of the microstructure of the homopolymers and copolymers reveals that styrene polymerization is highly regioselective and occurs prevalently through 2,1-monomer insertion. DFT calculations evidenced that steric interaction between the growing chain and the monomer in the transition state insertion stage is at the origin of this selectivity. The formation of isotactic polystyrene with a chain-end like microstructure is rationalized on the base of a mechanism similar to that proposed for the syndiospecific propene polymerization catalyzed by bis(phenoxyimine) titanium dichloride complexes. Finally, a general stereocontrol mechanism operative in olefin polymerization with this class of complexes is proposed. © 2012 American Chemical Society.

Mechanism of isotactic styrene polymerization with a C 6F 5-substituted bis(phenoxyimine) titanium system

KAUST Repository

Caporaso, Lucia

2012-11-13

We report a combined, experimental and theoretical, study of styrene polymerization to clarify the regio- and stereocontrol mechanism operating with a C 6F 5-substituted bis(phenoxyimine) titanium dichloride complex. Styrene homopolymerization, styrene-propene and styrene-ethene-propene copolymerizations have been carried out to this aim. A combination of 13C NMR analysis of the chain-end groups and of the microstructure of the homopolymers and copolymers reveals that styrene polymerization is highly regioselective and occurs prevalently through 2,1-monomer insertion. DFT calculations evidenced that steric interaction between the growing chain and the monomer in the transition state insertion stage is at the origin of this selectivity. The formation of isotactic polystyrene with a chain-end like microstructure is rationalized on the base of a mechanism similar to that proposed for the syndiospecific propene polymerization catalyzed by bis(phenoxyimine) titanium dichloride complexes. Finally, a general stereocontrol mechanism operative in olefin polymerization with this class of complexes is proposed. © 2012 American Chemical Society.

Quality evaluation of polypropylene packaged corn yogurt during storage

Science.gov (United States)

Aini, Nur; Prihananto, V.; Sustriawan, B.; Astuti, Y.; Maulina, M. R.

2018-01-01

Packaging is an important factor to control the process of quality decrease of any food product, including to determine the shelf life. The objective of this study was to determine changes quality of corn yogurt packaged using polypropylene. The method were using was package yogurt polypropylene, then it was stored in a refrigerator at 5, 10, or 15°C during 21 days. The yogurt was analysed every 7 days over a 21-day period. The results indicate that protein content decreased during storage, while the lactic acid bacteria, total acid, pH, viscosity, and total solids were increased. At the end of storage, the amount of lactic acid bacteria still fulfil the minimum requirements of a probiotic food, with a count of 6.407 log CFU/g. Overal scoring by panelist (scores ranged from 0 to 5) have a 4.78 at the beginning of storage. By the 21st day of storage, yogurt was packaging using transparent polypropylene having a score of 3.85, and that stored in opaque white packaging having a value of 3.95.

Development and characterisation of injection moulded, all-polypropylene composites

Directory of Open Access Journals (Sweden)

A. Kmetty

2013-02-01

Full Text Available In this work, all-polypropylene composites (all-PP composites were manufactured by injection moulding. Prior to injection moulding, pre-impregnated pellets were prepared by a three-step process (filament winding, compression moulding and pelletizing. A highly oriented polypropylene multifilament was used as the reinforcement material, and a random polypropylene copolymer (with ethylene was used as the matrix material. Plaque specimens were injection moulded from the pellets with either a film gate or a fan gate. The compression moulded sheets and injection moulding plaques were characterised by shrinkage tests, static tensile tests, dynamic mechanical analysis and falling weight impact tests; the fibre distribution and fibre/matrix adhesion were analysed with light microscopy and scanning electron microscopy. The results showed that with increasing fibre content, both the yield stress and the perforation energy significantly increased. Of the two types of gates used, the fan gate caused the mechanical properties of the plaque specimens to become more homogeneous (i.e., the differences in behaviour parallel and perpendicular to the flow direction became negligible.

Degradation of Polypropylene Membranes Applied in Membrane Distillation Crystallizer

Directory of Open Access Journals (Sweden)

Marek Gryta

2016-03-01

Full Text Available The studies on the resistance to degradation of capillary polypropylene membranes assembled in a membrane crystallizer were performed. The supersaturation state of salt was achieved by evaporation of water from the NaCl saturated solutions using membrane distillation process. A high feed temperature (363 K was used in order to enhance the degradation effects and to shorten the test times. Salt crystallization was carried out by the application of batch or fluidized bed crystallizer. A significant membrane scaling was observed regardless of the method of realized crystallization. The SEM-EDS, DSC, and FTIR methods were used for investigations of polypropylene degradation. The salt crystallization onto the membrane surface accelerated polypropylene degradation. Due to a polymer degradation, the presence of carbonyl groups on the membranes’ surface was identified. Besides the changes in the chemical structure a significant mechanical damage of the membranes, mainly caused by the internal scaling, was also found. As a result, the membranes were severely damaged after 150 h of process operation. A high level of salt rejection was maintained despite damage to the external membrane surface.

Synthesis And Thermal Characterization Of Polypropylene ...

African Journals Online (AJOL)

The present work investigates the heat transfer and specifically, thermal conductivity, diffusivity and specific heat in Aluminium composite materials. The composites were obtained by mixing polypropylene (PP) with oxidized Aluminium (Al) under various volume fractions. Two sizes of filler are used in the sample composite ...

Resterilized Polypropylene Mesh for Inguinal Hernia Repair

African Journals Online (AJOL)

2018-04-19

Apr 19, 2018 ... Conclusion: The use of sterilized polypropylene mesh for the repair of inguinal ... and nonabsorbable materials to reduce the tissue–mesh. INTRODUCTION ... which we have been practicing in our center since we introduced ...

IPP (Innovation in Products and Processes) For the sector of mineral raw materials and energy

International Nuclear Information System (INIS)

Correa E, Alexander; Alvarez, Carlos; Rodriguez, Andres

2009-01-01

This article presents the results of the research project IPP (process and product innovation) which is a systemic and thorough analysis of production chains, based on the study - productivity and processes. This project is working in 4 phases: Intelligence, experimentation, innovation, and technological appropriation, These steps are aimed at continuous improvement of processes, Products of the organization and the interactions between actors in the production of mineral raw materials and energy. In the intelligence phase, we studied the characteristics, needs, market, and environment of the production chain that are the result of the use of natural resources and environment. In the second phase, characterized the development, design and implementation of prototype products and processes that emulate the behavior of the process in a real system and are environmentally friendly. Taking into account the first two phases in the third, saw the formulation and design new processes and products that improve efficiency and productivity. In the last phase of the project is the service that seeks to appropriate technological innovation and knowledge transfer from one end to the chain. Finally the result of the proposed IPP is a center of innovation and development of logistic practices within the National University of Colombia to ensure the ownership and suitability of the solutions to the production chains is an innovation for the mining sector, materials and energy with the early-friendly products and processes with the environment.

Effect of compatibilization and reprocessing on the isothermal crystallization kinetics of polypropylene/wood flour composites

Directory of Open Access Journals (Sweden)

Arieny Rodrigues

2013-01-01

Full Text Available Numerous studies have focused on polymer mixtures aimed at the potential applications of these materials. This work analyzed the effect of polymer reprocessing and the type and concentration of compatibilizer on the isothermal crystallization kinetics of polypropylene/wood flour composites. The composites, which were polypropylene grafted with acrylic acid (PP-g-AA and maleic anhydride (PP-g-MA, were processed in a twin screw extruder with and without compatibilizer. Reprocessed polypropylene reached complete crystallization in less time than the composites with virgin polypropylene. The addition of wood flour to the composites did not change the kinetics significantly compared to that of the pure polymers, but the compatibilizers did, particularly PP-g-AA. The nucleation exponent (n and crystallization rate (K were calculated from Avrami plots. The values of n ranged from 2 to 3, indicating instantaneous to sporadic nucleation. The crystallization half-time of reprocessed polypropylene was shorter than that of virgin polypropylene and of the compositions containing PP-g-AA compatibilizer. The activation energy of crystallization and the equilibrium melting temperature were calculated, respectively, from Arrhenius and Hoffman-Weeks plots. Both of these parameters showed lower values in the composites, particularly in the ones containing compatibilizers.

A Study on Creep Behavior of Wood Flour- Recycled Polypropylene Composite

Directory of Open Access Journals (Sweden)

Saman Ghahri

2013-06-01

Full Text Available The creep behavior of wood flour- recycled polypropylene composites (with and without compatibilizer has been evaluated in this study. For this purpose, virgin polypropylene (PP was thermo-mechanically degraded by five times of extrusion under controlled conditions in a twin-screw extruder at a rotor speed of 100 rpm and at temperature of 1900C. The virgin and recycled polypropylene were mixed with the wood flour (50/50% W/W as well as the compatibilizer (0, 2% W/W by a counter-rotating twin-screw extruder to manufacture the wood flour-PP composites (WPCs samples. The nominal cross section of the manufactured composites was 70×10 mm2. Short term flexural creep test at 30% of ultimate bending load was performed by using flexural creep equipment. The total time to complete every test was 120 min (60 min creep and 60 min recovery. Results revealed that recycling of the PP reduced the creep resistance in composites containing recycled polypropylene. Also results have shown that with the presence of compatibilizer (MAPP creep deflection, creep factor and relative creep decrease and creep modulus increase. The composites containing virgin PP and MAPP exhibited higher creep resistance than those containing recycled PP.

Chemical modification of flax reinforced polypropylene composites

CSIR Research Space (South Africa)

Jacob John, Maya

2009-04-01

Full Text Available This paper presents an experimental study on the static and dynamic mechanical properties of nonwoven based flax fibre reinforced polypropylene composites. The effect of zein modification on flax fibres is also reported. Flax nonwovens were treated...

Essential work of fracture analysis for starch filled poly(propylene carbonate) composites

International Nuclear Information System (INIS)

Wang, X.L.; Li, R.K.Y.; Cao, Y.X.; Meng, Y.Z.

2007-01-01

Starch filled poly(propylene carbonate) composites are environmental friendly materials. In this study, the fracture toughness of composites under mode I loading was determined by the essential work of fracture concept. The specific essential fracture work of the poly(propylene carbonate)/starch composites decreases with increasing the starch content, while the non-essential work term, βw p increases with increasing the starch content. In addition, the morphologies, thermal properties, thermo-mechanical properties were studied by scanning electron microscope, thermogravimetric analysis, dynamic mechanical analysis, and differential scanning calorimetry, respectively. The thermal and thermo-mechanical measurements revealed that increasing starch content led to an increase in glass transition temperature and thermal stability. Morphology observation indicates that poly(propylene carbonate) and starch have weak interfacial adhesion

Carbon ion irradiation induced surface modification of polypropylene

International Nuclear Information System (INIS)

Saha, A.; Chakraborty, V.; Dutta, R.K.; Chintalapudi, S.N.

2001-01-01

Polypropylene was irradiated with 12 C ions of 3.6 and 5.4 MeV energies in the fluence range of 5x10 13 -5x10 14 ions/cm 2 using 3 MV tandem accelerator. Ion penetration was limited to a few microns and surface modifications were investigated by scanning electron microscopy. At the lowest ion fluence only blister formation of various sizes (1-6 μm) were observed, but at higher fluence (1x10 14 ions/cm 2 ) a three-dimensional network structure was found to form. A gradual degradation in the network structure was observed with further increase in the ion fluence. The dose dependence of the changes on surface morphology of polypropylene is discussed

Carbon ion irradiation induced surface modification of polypropylene

Energy Technology Data Exchange (ETDEWEB)

Saha, A. E-mail: abhijit@alpha.iuc.res.in; Chakraborty, V.; Dutta, R.K.; Chintalapudi, S.N

2001-12-01

Polypropylene was irradiated with {sup 12}C ions of 3.6 and 5.4 MeV energies in the fluence range of 5x10{sup 13}-5x10{sup 14} ions/cm{sup 2} using 3 MV tandem accelerator. Ion penetration was limited to a few microns and surface modifications were investigated by scanning electron microscopy. At the lowest ion fluence only blister formation of various sizes (1-6 {mu}m) were observed, but at higher fluence (1x10{sup 14} ions/cm{sup 2}) a three-dimensional network structure was found to form. A gradual degradation in the network structure was observed with further increase in the ion fluence. The dose dependence of the changes on surface morphology of polypropylene is discussed.

Rheological and Thermal Behavior of Polypropylene-Kaolin Composites

International Nuclear Information System (INIS)

Teng, S.T.; Nor Azura Abdul Rahim; Lan, D.N.U

2014-01-01

Kaolins effect on rheological behaviour of polypropylene-kaolin composites was investigated. The research found that not only the kaolin content influence the rheological behaviour but also the compounding using internal mixer and twin screw extruder. In details, viscosity and shear stress increased with addition of kaolin content. These characteristics also exhibited higher in polypropylene-kaolin composite suspensions compounded using twin screw extruder than using internal mixer. Chain scission was assumed to occur and affect the melt properties. Further justification characterized by Differential Scanning Calorimeter (DSC) showed that the effect of kaolin and loading content were more evident on the onset melting temperature and crystallinity. Besides, due to the different cooling operation in both processes, the effect of compounding on melting characteristic was conspicuous. (author)

Modification of low density polyethylene, isostatic polypropylene and their blends by gamma radiation

International Nuclear Information System (INIS)

Santos Rosa, D. dos

1991-01-01

The effects of the gamma radiation (of a 60 Co source), over low density polyethylene, isostatic polypropylene and their blends of low density polyethylene / polypropylene were studied. The structures modifications were attended by infrared spectrometry (IV), differential scanning calorimeter (DSC), strain-strain measurement, density measurement and scanning electron microscope (SEM). (author)

Effect of Mixing Process on Polypropylene Modified Bituminous Concrete Mix Properties

OpenAIRE

Noor Zainab Habib; Ibrahim Kamaruddin; Madzalan Napiah; Isa Mohd Tan

2011-01-01

This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely cont...

Mechanical and rheological response of polypropylene/boehmite nanocomposites

CSIR Research Space (South Africa)

Pedrazzoli, D

2014-01-01

Full Text Available In this work the influence of synthetic boehmite alumina (BA) nanoparticles with various surface treatments on the morphology, crystallization behavior and mechanical properties of polypropylene copolymer (PP) nanocomposites was studied...

Effect of processing conditions on the mechanical and thermal properties of high-impact polypropylene nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Furlan, L G [Federal Institute of Rio Grande do Sul, IFRS, Campus Restinga, Estrada Joao Antonio da Silveira, 351, Porto Alegre 91790-400 (Brazil); Ferreira, C I; Dal Castel, C; Santos, K S; Mello, A C.E. [Chemistry Institute, Federal University of Rio Grande do Sul, UFRGS, Av. Bento Goncalves, 9500, Porto Alegre 91501-970 (Brazil); Liberman, S A; Oviedo, M A.S. [Braskem S.A., III Polo Petroquimico, Via Oeste, Lote 5, Triunfo 95853-000 (Brazil); Mauler, R.S., E-mail: mauler@iq.ufrgs.br [Chemistry Institute, Federal University of Rio Grande do Sul, UFRGS, Av. Bento Goncalves, 9500, Porto Alegre 91501-970 (Brazil)

2011-08-25

Highlights: {yields} Polypropylene montmorillonite (PP-MMT) produced at different processing conditions. {yields} Polypropylene Nanocomposites with higher increase on impact resistance. {yields} Higher enhancement on mechanical properties. - Abstract: Polypropylene montmorillonite (PP-MMT) nanocomposites have been prepared by using a co-rotating twin screw extruder. The effects of processing conditions at fixed clay content (5 wt%) on polymer properties were investigated by means of transmission electron microscopy (TEM), flexural modulus, izod impact, dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). It was noticed that the morphology and the mechanical properties of polypropylene nanocomposites were affected by different screw shear configuration. The results showed that the higher enhancement on mechanical properties was obtained by medium shear intensity profile instead of high configuration. An exceptional increase (maximum of 282%) on impact resistance was observed.

Effect of processing conditions on the mechanical and thermal properties of high-impact polypropylene nanocomposites

International Nuclear Information System (INIS)

Furlan, L.G.; Ferreira, C.I.; Dal Castel, C.; Santos, K.S.; Mello, A.C.E.; Liberman, S.A.; Oviedo, M.A.S.; Mauler, R.S.

2011-01-01

Highlights: → Polypropylene montmorillonite (PP-MMT) produced at different processing conditions. → Polypropylene Nanocomposites with higher increase on impact resistance. → Higher enhancement on mechanical properties. - Abstract: Polypropylene montmorillonite (PP-MMT) nanocomposites have been prepared by using a co-rotating twin screw extruder. The effects of processing conditions at fixed clay content (5 wt%) on polymer properties were investigated by means of transmission electron microscopy (TEM), flexural modulus, izod impact, dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). It was noticed that the morphology and the mechanical properties of polypropylene nanocomposites were affected by different screw shear configuration. The results showed that the higher enhancement on mechanical properties was obtained by medium shear intensity profile instead of high configuration. An exceptional increase (maximum of 282%) on impact resistance was observed.

Flammability of polypropylene/organoclay nanocomposites; Inflamabilidade de nanocompositos de polipropileno/argila organofilica

Energy Technology Data Exchange (ETDEWEB)

Alves, Tatianny Soares; Barbosa, Renata [Universidade Federal do Piaui (UFPI), Teresina (Brazil); Carvalho, Laura Hecker de [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Canedo, Eduardo Luis [Instituto de Tecnologia de Pernambuco, Recife (Brazil)

2014-11-01

The flammabilities of nanocomposites made with three polypropylene grades (homo and copolymers) with 5 wt % of organoclay (Cloisite 20A), 5 or 15 wt % of maleated polypropylene as compatibilizer, and 0, 0.5 or 1 wt % of cis-13-docosenamide (Erucamide) as co-intercalant, were studied using the horizontal burning test UL94HB. Masterbatches prepared in an internal mixer were diluted in the polypropylene matrix using a corotating twin-screw extruder, with different screw configurations and operating at 240 or 480 rpm. Results indicate that the high burning rate of the composites was not affected by the processing conditions. For all formulations was observed a significant reduction in smoke release, lack of dripping and the formation of a char surface layer, that protected the core of the samples. (author)

Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

NARCIS (Netherlands)

Grossiord, N.; Wouters, M.E.L.; Miltner, H.E.; Lu, K.; Loos, J.; Van Mele, B.; Koning, C.E.

2010-01-01

Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene

Short-term flow induced crystallization in isotactic polypropylene : how short is short?

NARCIS (Netherlands)

Ma, Z.; Balzano, L.; Portale, G.; Peters, G.W.M.

2013-01-01

The so-called "short-term flow" protocol is widely applied in experimental flow-induced crystallization studies on polymers in order to separate the nucleation and subsequent growth processes [Liedauer et al. Int. Polym. Proc. 1993, 8, 236–244]. The basis of this protocol is the assumption that

Functionalization of silica nanoparticles for polypropylene nanocomposites applications

International Nuclear Information System (INIS)

Bracho, Diego; Palza, Humberto; Quijada, Raul; Dougnac, Vivianne

2011-01-01

Synthetic silica nanospheres of different diameters produced via the sol-gel method were used in order to enhance the barrier properties of the polypropylene-silica nanocomposites. Modification of the silica surface by reaction with organic chlorosilanes was performed in order to improve the particles interaction with the polypropylene matrix and its dispersion. Unmodified and modified silica nanoparticles were characterized using electronic microscopy (TEM), elemental analysis, thermo gravimetric analysis (TGA), and solid state nuclear magnetic resonance (NMR) spectroscopy. Preliminary permeability tests of the polymer-silica nanocomposite films showed no significant change at low particles load (3 wt%) regardless its size or surface functionality, mainly because of the low aspect ratio of the silica nanospheres. However, it is expected that at a higher concentration of silica particles differences will be observed. (author)

Surface modification of polypropylene membrane by polyethylene glycol graft polymerization

Energy Technology Data Exchange (ETDEWEB)

Abednejad, Atiye Sadat, E-mail: atiyeabednejad@gmail.com [Department of Biomedical Engineering, Faculty of New Sciences and Technologies, University of Tehran, P.O. Box 14395-1561, Tehran (Iran, Islamic Republic of); Amoabediny, Ghasem [Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, P.O. Box 14395-1561, Tehran (Iran, Islamic Republic of); Research Center for New Technologies in Life Science Engineering, University of Tehran, P.O. Box 63894-14179, Tehran (Iran, Islamic Republic of); Ghaee, Azadeh [Department of Biomedical Engineering, Faculty of New Sciences and Technologies, University of Tehran, P.O. Box 14395-1561, Tehran (Iran, Islamic Republic of)

2014-09-01

Polypropylene hollow fiber microporous membranes have been used in a wide range of applications, including blood oxygenator. The hydrophobic feature of the polypropylene surface causes membrane fouling. To minimize fouling, a modification consisting of three steps: surface activation in H{sub 2} and O{sub 2} plasma, membrane immersion in polyethylene glycol (PEG) and plasma graft polymerization was performed. The membranes were characterized by contact angle measurement, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM). Oxygen transfer of modified membranes was also tested. The stability of grafted PEG was measured in water and in phosphate buffer saline (PBS) at 37 °C. Blood compatibility of modified surfaces was evaluated by the platelet adhesion method. Water contact angel reduction from 110° to 72° demonstrates the enhanced hydrophilicity, and XPS results verify the presence of oxygenated functional groups due to the peak existence in 286 eV as a result of PEG grafting. The results clearly indicate that plasma graft-polymerization of PEG is an effective way for antifouling improvement of polypropylene membranes. Also, the results show that oxygen transfer changes in PEG grafted membranes are not significant. - Highlights: • H{sub 2} and O{sub 2} plasma graft polymerization of PEG on polypropylene membrane was carried out. • Changes in surface properties were investigated by FTIR, XPS, SEM, and AFM. • Surface wettability enhanced as a result of poly ethylene glycol grafting. • PEG grafting degree increase causes reduction of fouling and adhesion.

Storing of Extracts in Polypropylene Microcentrifuge Tubes Yields Contaminant Peak During Ultra-flow Liquid Chromatographic Analysis

OpenAIRE

Kshirsagar, Parthraj R.; Hegde, Harsha; Pai, Sandeep R.

2016-01-01

Background and Aim: This study was designed to understand the effect of storage in polypropylene microcentrifuge tubes and glass vials during ultra-flow liquid chromatographic (UFLC) analysis. Materials and Methods: One ml of methanol was placed in polypropylene microcentrifuge tubes (PP material, Autoclavable) and glass vials (Borosilicate) separately for 1, 2, 4, 8, 10, 20, 40, and 80 days intervals stored at ?4?C. Results: Contaminant peak was detected in methanol stored in polypropylene m...

Catalytic copyrolysis of particle board and polypropylene over Al-MCM-48

Energy Technology Data Exchange (ETDEWEB)

Kim, Hannah; Choi, Suek Ju [School of Environmental Engineering, University of Seoul, Seoul 02504 (Korea, Republic of); Kim, Ji Man [Department of Chemistry, Sungkyunkwan University, Suwon 16419 (Korea, Republic of); Jeon, Jong-Ki [Department of Chemical Engineering, Kongju National University, Cheonan 31080 (Korea, Republic of); Park, Sung Hoon; Jung, Sang-Chul [Department of Environmental Engineering, Sunchon National University, Suncheon 57922 (Korea, Republic of); Kim, Sang Chai [Department of Environmental Education, Mokpo National University, Muan 58554 (Korea, Republic of); Park, Young-Kwon, E-mail: catalica@uos.ac.kr [School of Environmental Engineering, University of Seoul, Seoul 02504 (Korea, Republic of)

2016-10-15

Highlights: • Al-MCM-48 was used for catalytic copyrolysis of particle board and polypropylene. • Catalytic produced mainly hydrocarbons. • The hydrocarbons produced were mainly in the diesel range. - Abstract: Particle board and polypropylene (PP) at a mixing ratio of 1:1 were copyrolyzed over two Al-MCM-48 catalysts with Si/Al ratios of 20 and 80. The catalyst characteristics were examined by measuring the Brunauer-Emmett-Teller surface area, temperature programmed desorption of ammonia, and X-ray diffraction. The main pyrolysis products of particle board were oxygenates, acids, and phenolics, whereas a large quantity of hydrocarbons within the diesel fuel range was produced from copyrolysis with polypropylene. The catalytic copyrolysis of particle board and PP over the Al-MCM-48 catalysts produced bio-oil with a much larger hydrocarbon content than that from the catalytic pyrolysis of particle board only. The hydrocarbons produced were mainly in the diesel range, highlighting the potential for the production of high-quality fuel.

Mechanical Analysis of an upscaled version of the Vaporizer (pressure vessel and circulation tubes) of the incineration pilot power plant TEMO-IPP.

OpenAIRE

Kerdi, Banan El

2016-01-01

To be able to upscale the TEMO-IPP incineration plant to a commercial incineration plant in Tripoli (about40 MW) critical components shall be verified by Finite Element Analysis with the tool Abaqus. The main critical component is the pressure vessel with about 100 bar pressure difference.

Study on Welding Mechanism Based on Modification of Polypropylene for Improving the Laser Transmission Weldability to PA66

Science.gov (United States)

Liu, Huixia; Jiang, Hairong; Guo, Dehui; Chen, Guochun; Yan, Zhang; Li, Pin; Zhu, Hejun; Chen, Jun; Wang, Xiao

2015-01-01

Polypropylene and PA66 are widely used in our daily life, but they cannot be welded by laser transmission welding (LTW) because of polar differences and poor compatibility. In this paper, grafting modification technology is used to improve the welding performance between polypropylene and PA66. Firstly, the strong reactive and polar maleic-anhydride (MAH) is grafted to polypropylene and infrared spectrometer is used to prove that MAH has been grafted to polypropylene. At the same time, the mechanical and thermal properties of the graft modified polypropylene (TGMPP) are tested. The results prove that the grafting modification has little influence on them. Also, the optical properties of TGMPP are measured. Then, the high welding strength between TGMPP and PA66 is found and the mechanism of the weldability is researched, which shows that there are two reasons for the high welding strength. By observing the micro morphology of the welding zone, one reason found is that the modification of polypropylene can improve the compatibility between polypropylene and PA66 and make them easy to diffuse mutually, which causes many locking structures formed in the welding region. The other reason is that there are chemical reactions between TGMPP and PA66 proved by the X-ray photoelectron spectrometer. PMID:28793484

Texturing of polypropylene (PP) with nanosecond lasers

Science.gov (United States)

Riveiro, A.; Soto, R.; del Val, J.; Comesaña, R.; Boutinguiza, M.; Quintero, F.; Lusquiños, F.; Pou, J.

2016-06-01

Polypropylene (PP) is a biocompatible and biostable polymer, showing good mechanical properties that has been recently introduced in the biomedical field for bone repairing applications; however, its poor surface properties due to its low surface energy limit their use in biomedical applications. In this work, we have studied the topographical modification of polypropylene (PP) laser textured with Nd:YVO4 nanosecond lasers emitting at λ = 1064 nm, 532 nm, and 355 nm. First, optical response of this material under these laser wavelengths was determined. The application of an absorbing coating was also studied. The influence of the laser processing parameters on the surface modification of PP was investigated by means of statistically designed experiments. Processing maps to tailor the roughness, and wettability, the main parameters affecting cell adhesion characteristics of implants, were also determined. Microhardness measurements were performed to discern the impact of laser treatment on the final mechanical properties of PP.

Influence of procedure variables in formation and properties of polypropylene/bentonite nanocomposites

International Nuclear Information System (INIS)

Andrade, Daniela de Lourdes Anjos Coutinho Simoes

2009-01-01

The purpose of this work is to prepare nanocomposites of polypropylene/compatibilizer/bentonite, by melting intercalation, with a commercial sodium clay - Argel - as filler. This clay was organically purified and modified by different methods, with a quaternary ammonium salt. The clays were characterized by X-Ray diffraction (XRD), infrared spectroscopy (FTIR) and thermogravimetric analyses (TG) to determine the most efficient preparation method. Before that, in the second stage of this study, the influence of the type and contend of organoclay in the properties of the polypropylene films was measured; the same was done for the compatibilizer. The preliminary results indicate that the nanocomposites film with 1% of organoclay and 15% of polypropylene grafted with maleic anhydride show promise as packing materials and may be used, in the near future, as a new product by the national industry. (author)

Analysis and optimization of machining parameters of laser cutting for polypropylene composite

Science.gov (United States)

Deepa, A.; Padmanabhan, K.; Kuppan, P.

2017-11-01

Present works explains about machining of self-reinforced Polypropylene composite fabricated using hot compaction method. The objective of the experiment is to find optimum machining parameters for Polypropylene (PP). Laser power and Machining speed were the parameters considered in response to tensile test and Flexure test. Taguchi method is used for experimentation. Grey Relational Analysis (GRA) is used for multiple process parameter optimization. ANOVA (Analysis of Variance) is used to find impact for process parameter. Polypropylene has got the great application in various fields like, it is used in the form of foam in model aircraft and other radio-controlled vehicles, thin sheets (∼2-20μm) used as a dielectric, PP is also used in piping system, it is also been used in hernia and pelvic organ repair or protect new herrnis in the same location.

Effects of gamma irradiation on food contact polyethylene, polypropylene and polystyrene. Volatiles

International Nuclear Information System (INIS)

Kawamura, Yoko; Sayama, Kayo; Yamada, Takashi

2000-01-01

The effects of gamma irradiation on the generation of volatiles from food contact polyethylene and polypropylene were investigated using head space (HS)/GC/MS. All samples generated volatiles such as acetic acid, propionic acid, butanoic acid, 2,2-dimethylpropionic acid, acetone, 2-butanone, 2-propanol, 2-methyl-2-propanol, hydrocarbons, etc., due to the gamma irradiation. Especially, acetic acid and acetone were formed in greatest amounts. Since these volatiles did not exist before irradiation and their amounts increased with increasing irradiation dose, they should be degradation products from the polymer or additives by irradiation. Polypropylene generated more kinds and larger amounts of volatiles than polyethylene, which showed that polypropylene is more sensitive to irradiation. Polystyrene contained styrene and ethylbenzene as monomers before irradiation and their amounts decreased after irradiation. Polystyrene generated few degradation products during the irradiation. (author)

Study of microcellular injection-molded polypropylene/waste ground rubber tire powder blend

International Nuclear Information System (INIS)

Xin, Zhen Xiang; Zhang, Zhen Xiu; Pal, Kaushik; Byeon, Jong Ung; Lee, Sung Hyo; Kim, Jin Kuk

2010-01-01

Microcellular polypropylene/waste ground rubber tire powder blend processing was performed on an injection-molding machine with a chemical foaming agent. The molded samples produced based on the design of experiments (DOE) matrices were subjected to tensile testing and scanning electron microscope (SEM) analyses. Molding conditions and waste ground rubber tire (WGRT) powder have been found to have profound effects on the cell structures and mechanical properties of polypropylene (PP) and waste ground rubber tire powder composite samples. The result shows that microcellular PP/WGRT blend samples exhibit smaller cell size and higher cell density compare with polypropylene resin. Among the molding parameters studied, chemical foaming agent weight percentage has the most significant effect on cell size, cell density, and tensile strength. The results also suggest that tensile strength of microcellular PP/WGRT composites is sensitive to weight reduction, and skin thickness.

Development of a Halogen Free Flame Retardant Masterbatch for Polypropylene Fibers

Directory of Open Access Journals (Sweden)

François Rault

2015-02-01

Full Text Available The efficiency of new phosphinates, in combination with melamine cyanurate, was studied using different polypropylene textile structures. The influence of different ratios up to a total amount of 6 wt% in the polypropylene fiber was investigated using the limiting oxygen index (LOI and cone calorimeter method for research purposes, while the performances were correlated to the standards FMVSS 302 (Federal Motor Vehicle Safety Standards and DIN 4102-l (Deutsches Institut für Normung used more specifically for automotive and building sector.

New prospects in EU environmental policies. The Integrated Product Policy (IPP)

International Nuclear Information System (INIS)

Carnimeo, G.; Iraldo, F.

2000-01-01

The Integrated Product Policy - IPP - is becoming one of the top priorities for the European Commission within the framework of the product-oriented environmental policies. Rather than a new policy, this is an innovative approach aimed at co-originated existing and forthcoming environmental policies, in order to manage in an integrated way and minimise the impacts connected with the whole product life-cycle. The underlying life-cycle guideline requires the management of each phase by considering what happens in all the other phases. What clearly emerges from a research carried out by Iefe Bocconi is, on the one hand, the effectiveness of co-operation and networking between all the actors involved in the product environmental management within the different phases of its life cycle (policy makers, producers, retailers, consumers, NGOs, etc.) and, on the other, the opportunity of developing an integrated management of both environmental policy instruments and corporate management tools [it

Property Relationship in Organosilanes and Nanotubes Filled Polypropylene Hybrid Composites

Directory of Open Access Journals (Sweden)

Alejandra J. Monsiváis-Barrón

2014-10-01

Full Text Available Polypropylene composites with different filler contents were prepared by creating a masterbatch containing 3 wt%. filler. A variety of silanol groups were used to synthetized three compounds in different media trough a sol-gel process with acetic acid, formic acid and ammonium hydroxide as catalysts. Besides, four different nanotubular fillers were also used to analyze their behavior and compare it with the effect caused by the silanol groups. These tubular structures comprise: unmodified halloysite, carbon nanotubes and functionalized halloysite and carbon nanotubes. Morphological characterization in SEM and STEM/TEM showed dispersion in the polypropylene matrix. According to TGA and DSC measurements thermal behavior remain similar for all the composites. Mechanical test in tension demonstrate that modulus of the composites increases for all samples with a major impact for materials containing silanol groups synthetized in formic acid. Rheological measurements show a significantly increment in viscosity for samples containing unmodified and modified carbon nanotubes. No difference was found for samples containing silanol groups and halloysite when compared to neat polypropylene. Finally, the oxygen transmission rate increased for all samples showing high barrier properties only for samples containing natural and functionalized halloysite nanotubes.

Property Relationship in Organosilanes and Nanotubes Filled Polypropylene Hybrid Composites.

Science.gov (United States)

Monsiváis-Barrón, Alejandra J; Bonilla-Rios, Jaime; Sánchez-Fernández, Antonio

2014-10-20

Polypropylene composites with different filler contents were prepared by creating a masterbatch containing 3 wt%. filler. A variety of silanol groups were used to synthetized three compounds in different media trough a sol-gel process with acetic acid, formic acid and ammonium hydroxide as catalysts. Besides, four different nanotubular fillers were also used to analyze their behavior and compare it with the effect caused by the silanol groups. These tubular structures comprise: unmodified halloysite, carbon nanotubes and functionalized halloysite and carbon nanotubes. Morphological characterization in SEM and STEM/TEM showed dispersion in the polypropylene matrix. According to TGA and DSC measurements thermal behavior remain similar for all the composites. Mechanical test in tension demonstrate that modulus of the composites increases for all samples with a major impact for materials containing silanol groups synthetized in formic acid. Rheological measurements show a significantly increment in viscosity for samples containing unmodified and modified carbon nanotubes. No difference was found for samples containing silanol groups and halloysite when compared to neat polypropylene. Finally, the oxygen transmission rate increased for all samples showing high barrier properties only for samples containing natural and functionalized halloysite nanotubes.

Effects of gamma irradiation on polypropylene, polypropylene + high density polyethylene and polypropylene + high density polyethylene + wood flour

Energy Technology Data Exchange (ETDEWEB)

Reyes, J.; Albano, C.; Davidson, E.; Poleo, R. [Universidad Central de Venezuela, Caracas (Venezuela). Escuela de Quimica; Gonzalez, J.; Ichazo, M. [Universidad Simon Bolivar, Dept. de Mecanica, Caracas (Venezuela); Chipara, M. [Research Institute for Electrotechnics, Bucharest (Romania)

2001-04-01

The effect of the gamma-irradiation on the mechanical properties of the composites, Polypropylene (PP), PP+high density Polyethylene (HDPE), PP+ HDPE+wood flour, where HDPE is virgin and recycled, was studied. This paper discusses the behavior of the composites after exposure to various doses of gamma irradiation (1-7 MRads) in the presence of oxygen. The dependence of mechanical properties on the integral dose for a constant dose rate of 0.48 MRads/h confirms the influence of the irradiation. Strong effects on the elongation at break and break strength is noticed. The mathematical analysis suggests for the PP+r-HDPE a bimolecular process of the elongation at break. On the order hand, for the PP+HDPE a complex process is represented for a three exponential equation. (orig.)

Effects of gamma irradiation on polypropylene, polypropylene + high density polyethylene and polypropylene + high density polyethylene + wood flour

International Nuclear Information System (INIS)

Reyes, J.; Albano, C.; Davidson, E.; Poleo, R.; Chipara, M.

2001-01-01

The effect of the gamma-irradiation on the mechanical properties of the composites, Polypropylene (PP), PP+high density Polyethylene (HDPE), PP+ HDPE+wood flour, where HDPE is virgin and recycled, was studied. This paper discusses the behavior of the composites after exposure to various doses of gamma irradiation (1-7 MRads) in the presence of oxygen. The dependence of mechanical properties on the integral dose for a constant dose rate of 0.48 MRads/h confirms the influence of the irradiation. Strong effects on the elongation at break and break strength is noticed. The mathematical analysis suggests for the PP+r-HDPE a bimolecular process of the elongation at break. On the order hand, for the PP+HDPE a complex process is represented for a three exponential equation. (orig.)

Laparoscopic Pelvic Floor Repair Using Polypropylene Mesh

Directory of Open Access Journals (Sweden)

Shih-Shien Weng

2008-09-01

Conclusion: Laparoscopic pelvic floor repair using a single piece of polypropylene mesh combined with uterosacral ligament suspension appears to be a feasible procedure for the treatment of advanced vaginal vault prolapse and enterocele. Fewer mesh erosions and postoperative pain syndromes were seen in patients who had no previous pelvic floor reconstructive surgery.

Short- and long-term results of chordal reconstruction using artificial suture material (polytetrafluoroethylene and polypropylene in the dog

Directory of Open Access Journals (Sweden)

Isamu Kanemoto

2017-04-01

Full Text Available No previous reports have compared the suitability of expanded polytetrafluoroethylene (ePTFE and polypropylene as artificial suture materials for chordal reconstruction in mitral valve plasty (MVP in the dog. Twelve normal dogs were subjected to MVP using surfaceinduced deep hypothermia. In the short-term group (1.5-4 months after surgery, all ePTFE sutures were covered by a tissue sheath including the paired suture arms, which gave the appearance of native chordae from 2 months after surgery. In contrast, all polypropylene sutures were not covered by tissue, and appeared the same as the paired polypropylene suture arms at the operation. In the long-term group (12 months after surgery, all ePTFE sutures were covered by a tissue sheath, which appeared the same as that in the short-term group, and had flexibility without increased thickness with time. In contrast, although the polypropylene suture was covered completely by a tissue sheath in 1 dog, all the other polypropylene sutures were exposed except for both ends of the suture. ePTFE may be superior to polypropylene as an artificial suture material for chordal reconstruction in MVP.

Flexural strength of self compacting fiber reinforced concrete beams using polypropylene fiber: An experimental study

Science.gov (United States)

Lisantono, Ade; Praja, Baskoro Abdi; Hermawan, Billy Nouwen

2017-11-01

One of the methods to increase the tensile strength of concrete is adding a fiber material into the concrete. While to reduce a noise in a construction project, a self compacting concrete was a good choices in the project. This paper presents an experimental study of flexural behavior and strength of self compacting fiber reinforced concrete (RC) beams using polypropylene fiber. The micro monofilament polypropylene fibers with the proportion 0.9 kg/m3 of concrete weight were used in this study. Four beam specimens were cast and tested in this study. Two beams were cast of self compacting reinforced concrete without fiber, and two beams were cast of self compacting fiber reinforced concrete using polypropylene. The beams specimen had the section of (180×260) mm and the length was 2000 mm. The beams had simple supported with the span of 1800 mm. The longitudinal reinforcements were using diameter of 10 mm. Two reinforcements of Ø10 mm were put for compressive reinforcement and three reinforcements of Ø10 mm were put for tensile reinforcement. The shear reinforcement was using diameter of 8 mm. The shear reinforcements with spacing of 100 mm were put in the one fourth near to the support and the spacing of 150 mm were put in the middle span. Two points loading were used in the testing. The result shows that the load-carrying capacity of the self compacting reinforced concrete beam using polypropylene was a little bit higher than the self compacting reinforced concrete beam without polypropylene. The increment of load-carrying capacity of self compacting polypropylene fiber reinforced concrete was not so significant because the increment was only 2.80 % compare to self compacting non fiber reinforced concrete. And from the load-carrying capacity-deflection relationship curves show that both the self compacting polypropylene fiber reinforced concrete beam and the self compacting non fiber reinforced concrete beam were ductile beams.

Kenaf/PP and EFB/PP: Effect of fibre loading on the mechanical properties of polypropylene composites

Science.gov (United States)

Anuar, N. I. S.; Zakaria, S.; Harun, J.; Wang, C.

2017-07-01

Kenaf and empty fruit bunch (EFB) fibre which are the important natural fibres in Malaysia were studied as nonwoven polymer composites. The effect of fibre loading on kenaf polypropylene and EFB polypropylene nonwoven composite was studied at different mixture ratio. Kenaf polypropylene nonwoven composite (KPNC) and EFB polypropylene nonwoven composite (EPNC) were prepared by carding and needle-punching techniques, followed by a compression moulding at 6 mm thickness. This study was conducted to identify the optimum fibre loading of nonwoven polypropylene composite and their effect on the mechanical strength. The study was designed at 40%, 50%, 60% and 70% of fibre content in nonwoven mat and composite. The tensile strength, flexural strength and compression strength were tested to evaluate the composite mechanical properties. It was found that the mechanical properties for both kenaf and EFB nonwoven composites were influenced by the fibre content. KPNC showed higher mechanical strength than EPNC. The highest flexural strength was obtained at 60% KPNC and the lowest value was showed by 40% EPNC. The tensile and flexural strength for both KPNC and EPNC decreased after the fibre loading of 60%.

Properties analysis of tensile strength, crystallinity degree and microstructure of polymer composite polypropylene-sand

International Nuclear Information System (INIS)

Sudirman; Karo-Karo, Aloma; Ari-Handayani; Bambang-Sugeng; Rukihati; Mashuri

2004-01-01

Materials modification base on polymer toward polymer composite is needed by addition of filler. Mechanical properties such as tensile strength, crystallinity degree and microstructure of polymer composite based on polypropylene with sand filler have been investigated. In this work, the polymer composite has been made by mixing the matrix of polypropylene melt flow 2 (PP MF2) or polypropylene melt flow 10 (PP MF 10) with sand filler in a labo plastomill. The composition of sand filler was varied to 10, 30, 40 and 50 % v/v, a then the composite were casted to the film sheets form. The sheets were characterized mechanically i.e tensile strength, crystallinity degree and microstructure. The result showed that the tensile strength decreased by increasing the volume fraction of sand filler, in accordance with microstructure investigation that the matrix area under zone plastic deformation (more cracks), while the filler experienced elastic deformation, so that the strength mechanism of filler did not achieved with expectation (Danusso and Tieghi theory). For filler more than 30 % of volume fraction, the tensile strength of polypropylene melt flow 10 (PP MF 10) was greater than that polypropylene melt flow 2 (PP MF2). It was caused by plasticities in PP MF 10. The tensile strength of PP MF2 was greater than that PP MF 10 for volume fraction of sand filler less than 30 %. It was caused by PP MF2 to be have more degree of crystallinity

OPTIMIZATION OF PROCESS PARAMETERS FOR ENHANCED MECHANICAL PROPERTIES OF POLYPROPYLENE TERNARY NANOCOMPOSITES

Directory of Open Access Journals (Sweden)

Oladipupo Olaosebikan Ogunleye

2015-02-01

Full Text Available Preparation of Polypropylene ternary nanocomposites (PPTN was accomplished by blending multiwall carbon nanotube (MWCNT in polypropylene/clay binary system using a melt intercalation method. The effects of MWCNT loadings (A, melting temperature (B and mixing speed (C were investigated and optimized using central composite design. The analysis of the fitted cubic model clearly indicated that A and B were the main factors influencing the tensile properties at a fixed value of C. However, the analysis of variance showed that the interactions between the process parameters, such as; AB, AC, AB2, A2B and ABC, were highly significant on both tensile strength and Young’s modulus enhancement, while no interaction is significant in all models considered for elongation. The established optimal conditions gave 0.17%, 165 °C, and 120 rpm for A, B and C, respectively. These conditions yielded a percentage increase of 57 and 63% for tensile strength and Young’s modulus respectively compared to the virgin Polypropylene used.

The mechanical properties of unidirectional all-polypropylene composites

NARCIS (Netherlands)

Alcock, B.; Cabrera, N.O.; Barkoula, N.M.; Loos, J.; Peijs, A.A.J.M.

2006-01-01

The creation of highly oriented, co-extruded polypropylene (PP) tapes allows the production of recyclable ‘all-polypropylene’ composites, with a large temperature processing window (>30 °C) and a high volume fraction of highly oriented PP (>90%). These composites show little deviation of mechanical

Polypropylene/organoclay/SEBS nanocomposites with toughness-stiffness properties

DEFF Research Database (Denmark)

Sanporean (nee Potarniche), Catalina-Gabriela; Vuluga, Zina; Radovici, Constantin

2014-01-01

Polypropylene nanocomposites with a different amount of styrene-ethylene-butylene-styrene block copolymer (SEBS)/clay were prepared via a melt mixing technique. To improve the dispersion of commercial organoclay (denoted as OMMT), various amounts of SEBS were incorporated. At a fixed content of O...

Analysis of Nanodomain Composition in High-Impact Polypropylene by Atomic Force Microscopy-Infrared.

Science.gov (United States)

Tang, Fuguang; Bao, Peite; Su, Zhaohui

2016-05-03

In this paper, compositions of nanodomains in a commercial high-impact polypropylene (HIPP) were investigated by an atomic force microscopy-infrared (AFM-IR) technique. An AFM-IR quantitative analysis method was established for the first time, which was then employed to analyze the polyethylene content in the nanoscopic domains of the rubber particles dispersed in the polypropylene matrix. It was found that the polyethylene content in the matrix was close to zero and was high in the rubbery intermediate layers, both as expected. However, the major component of the rigid cores of the rubber particles was found to be polypropylene rather than polyethylene, contrary to what was previously believed. The finding provides new insight into the complicated structure of HIPPs, and the AFM-IR quantitative method reported here offers a useful tool for assessing compositions of nanoscopic domains in complex polymeric systems.

Reel-to-Reel Atmospheric Pressure Dielectric Barrier Discharge (DBD Plasma Treatment of Polypropylene Films

Directory of Open Access Journals (Sweden)

Lukas JW Seidelmann

2017-03-01

Full Text Available Atmospheric pressure plasma treatment of the surface of a polypropylene film can significantly increase its surface energy and, thereby improve the printability of the film. A laboratory-scale dielectric barrier discharge (DBD system has therefore been developed, which simulates the electrode configuration and reel-to-reel web transport mechanism used in a typical industrial-scale system. By treating the polypropylene in a nitrogen discharge, we have shown that the water contact angle could be reduced by as much as 40° compared to the untreated film, corresponding to an increase in surface energy of 14 mNm−1. Ink pull-off tests showed that the DBD plasma treatment resulted in excellent adhesion of solvent-based inks to the polypropylene film.

Colorimetry analysis of polypropylene-polyethylene base copoliners

International Nuclear Information System (INIS)

Sunol, J. J.; Saurina, J.; Carrasco, F.; Pages, P.

1998-01-01

In this paper, crystallisation process study has been performed, from the molten material, in polypropylene-polyethylene (PP-PE) copolymers rich in PP (∼ 95 wgh.%), using different additives. Some samples have been artificially aged. Calorimetric analysis has been performed by different scanning calorimetry (DSC), from which crystallisation kinetics has been studied under dynamic conditions. (Author) 22 refs

The effect of impact modifier and of nucleating agent on the radiation tolerance of polypropylene

Energy Technology Data Exchange (ETDEWEB)

Liu Dongyuan (Beijing Normal Univ., BJ (China)); Czvikovszky, T.; Dobo, J.; Somogyi, A. (Research Inst. for the Plastics Industry, Budapest (Hungary))

1990-01-01

The effect of two types of additives was investigated with respect to the oxidative post-irradiation stability of polypropylene: SBS thermoplastic rubbers as impact modifiers and benzoic acid as nucleating agent. Testing was performed by ultimate deformation on bending. The thermoplastic rubber additive increased the post-irradiation stability of polypropylene substantially. (author).

The effect of impact modifier and of nucleating agent on the radiation tolerance of polypropylene

International Nuclear Information System (INIS)

Liu Dongyuan; Czvikovszky, T.; Dobo, J.; Somogyi, A.

1990-01-01

The effect of two types of additives was investigated with respect to the oxidative post-irradiation stability of polypropylene: SBS thermoplastic rubbers as impact modifiers and benzoic acid as nucleating agent. Testing was performed by ultimate deformation on bending. The thermoplastic rubber additive increased the post-irradiation stability of polypropylene substantially. (author)

Environmental and Cost Assessment of a Polypropylene Nanocomposite

NARCIS (Netherlands)

Roes, A.L.|info:eu-repo/dai/nl/303022388; Marsili, E.; Nieuwlaar, E.|info:eu-repo/dai/nl/073931373; Patel, M.K.|info:eu-repo/dai/nl/18988097X

2007-01-01

This paper describes a study on the use of a polypropylene (PP)/layered silicate nanocomposite as packaging film, agricultural film, and automotive panels. The study’s main question was “Are the environmental impacts and costs throughout the life cycle of nanocomposite products lower than those of

Tensile strength characteristics of polypropylene composites reinforced with stone groundwood fibers from softwood

OpenAIRE

López, Joan Pere; Méndez González, José Alberto; Espinach Orús, Xavier; Julián Pérez, Fernando; Mutjé Pujol, Pere; Vilaseca Morera, Fabiola

2012-01-01

The behavior of stone groundwood / polypropylene injection-molded composites was evaluated with and without coupling agent. Stone groundwood (SGW) is a fibrous material commonly prepared in a high yield process and mainly used for papermaking applications. In this work, the use of SGW fibers was explored as a reinforcing element of polypropylene (PP) composites. The surface charge density of the composite components was evaluated, as well as the fiber’s length and diameter inside the composit...

Vibration behaviour of foamed concrete floor with polypropylene and rise husk ash fibre

Science.gov (United States)

Azaman, N. A. Mohd; Ghafar, N. H. Abd; Ayub, N.; Ibrahim, M. Z.

2017-11-01

In the history of the construction industry, lightweight concrete or foamed concrete is a special concrete which can very useful in the construction sector because it is very lightweight and it can compact by itself at each angle of foamwork. Foamed concrete is one of lightweight concrete which widely used for floor construction due to its light weight and economic. The significant challenges in the floor design process are considering the vibration that needs improvements for the poor dynamic behaviour insulation. An alternative material to replace sand with certain amount of rice husk ash (RHA) and polypropylene was introduced. Research was determine the dynamic behavior of foam-polypropylene and foam-RHA concrete by using impact hammer test. The natural frequency for normal foamed concrete, 0.5 % of Polypropylene and 15% of RHA is 29.8 Hz, 29.3 Hz and 29.5 Hz respectively.

Brayton Isotope Power System (BIPS). Phase I: Integrated Program Plan (IPP). Report 75-311574A

International Nuclear Information System (INIS)

1976-01-01

The government, AIRPHX, AIRLA, and contractor BIPS program coordination efforts are discussed. These coordination efforts are essential for defining program objectives, and achieving these objectives in an efficient manner. The IPP outlines a long range effort intended to: (a) develop end product confidence; (b) identify government and contractor activities pertinent and contributory to BIPS development; (c) recommend government and contractor activities required to ensure BIPS program success; (d) establish activity priorities based on program cost and schedule impacts, and achievement of technical objectives; (e) coordinate the efforts of contributing agencies; (f) provide general information and, to a limited extent, BIPS program-related development activity status to interested individuals and agencies; and (g) provide contractor team program planning guidance

Mechanical properties of pineapple leaf fibre reinforced polypropylene composites

International Nuclear Information System (INIS)

Arib, R.M.N.; Sapuan, S.M.; Ahmad, M.M.H.M.; Paridah, M.T.; Zaman, H.M.D. Khairul

2006-01-01

Pineapple leaf fibre, which is rich in cellulose, relative inexpensive and abundantly available has the potential for polymer-reinforced composite. The present study investigates the tensile and flexural behaviours of pineapple leaf fibre-polypropylene composites as a function of volume fraction. The tensile modulus and tensile strength of the composites were found to be increasing with fibre content in accordance with the rule of mixtures. The tensile modulus and tensile strength with a volume fraction 10.8% are 687.02 and 37.28 MPa, respectively. The flexural modulus gives higher value at 2.7% volume fraction. The flexural strength of the composites containing 5.4% volume fraction was found to be higher than that of pure polypropylene resin by 5.1%. Scanning electron microscopic studies were carried out to understand the fibre-matrix adhesion and fibre breakage

Mechanical properties of pineapple leaf fibre reinforced polypropylene composites

Energy Technology Data Exchange (ETDEWEB)

Arib, R.M.N. [Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Sapuan, S.M. [Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia)]. E-mail: sapuan@eng.upm.edu.my; Ahmad, M.M.H.M. [Department of Mechanical and Manufacturing Engineering, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Paridah, M.T. [Faculty of Forestry, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Zaman, H.M.D. Khairul [Radiation Processing Technology Division, Malaysian Institute for Nuclear Technology Research (MINT), Bangi 43000 Kajang, Selangor (Malaysia)

2006-07-01

Pineapple leaf fibre, which is rich in cellulose, relative inexpensive and abundantly available has the potential for polymer-reinforced composite. The present study investigates the tensile and flexural behaviours of pineapple leaf fibre-polypropylene composites as a function of volume fraction. The tensile modulus and tensile strength of the composites were found to be increasing with fibre content in accordance with the rule of mixtures. The tensile modulus and tensile strength with a volume fraction 10.8% are 687.02 and 37.28 MPa, respectively. The flexural modulus gives higher value at 2.7% volume fraction. The flexural strength of the composites containing 5.4% volume fraction was found to be higher than that of pure polypropylene resin by 5.1%. Scanning electron microscopic studies were carried out to understand the fibre-matrix adhesion and fibre breakage.

Ziegler-Natta catalyst for polypropylene and polyethylene nanocomposites preparation

International Nuclear Information System (INIS)

Silvino, Alexandre C.; Dias, Marcos L.; Bezerra, Ana Beatriz F.

2009-01-01

Polypropylene and polyethylene nanocomposites are well known for their improved properties when compared with the neat polymers. In this work we report the preparation, characterization and the activity studies of a fourth generation Ziegler-Natta catalyst for the preparation of polyolefin/clay nanocomposites. The catalyst was prepared treating an organo-modified silicate with magnesium and titanium compounds. The content of titanium and that of the magnesium of the catalyst were determined by UV-vis spectroscopy and atomic absorption respectively. The first results show that the catalyst is active for propylene polymerization being suitable for polypropylene/clay nanocomposite preparation. The catalyst activity for ethylene polymerization was also investigated. The X-ray diffraction patterns of the polyethylene samples suggest the clay exfoliation occurs in the in situ polymerization, even with high clay loading (about 9 %) indicating that a nanocomposite was formed. (author)

Electrochemical Impedance Study of Zinc Yellow Polypropylene-Coated Aluminum Alloy

Directory of Open Access Journals (Sweden)

Zhi-hua Sun

2010-01-01

Full Text Available Performance of zinc yellow polypropylene-coated aluminum alloy 7B04 during accelerated degradation test is studied using electrochemical impedance spectroscopy (EIS. It has been found that the zinc yellow polypropylene paint has few flaw and acts as a pure capacitance before accelerated test. After 336-hour exposure to the test, the impedance spectroscopy shows two time constants, and water has reached to the aluminum alloy/paint interface and forms corrosive microcell. For the scratched samples, the reaction of metal corrosion and the hydrolysis of zinc yellow ion can occur simultaneously. The impedance spectroscopy indicates inductance after 1008-hour exposure to the test, but the inductance disappears after 1344-hour exposure and the passivation film has pitting corrosion.

Optimization of the IPP Precursor Supply for the Production of Lycopene, Decaprenoxanthin and Astaxanthin by Corynebacterium glutamicum

International Nuclear Information System (INIS)

Heider, Sabine A. E.; Wolf, Natalie; Hofemeier, Arne; Peters-Wendisch, Petra; Wendisch, Volker F.

2014-01-01

The biotechnologically relevant bacterium Corynebacterium glutamicum, currently used for the million ton-scale production of amino acids for the food and feed industries, is pigmented due to synthesis of the rare cyclic C50 carotenoid decaprenoxanthin and its glucosides. The precursors of carotenoid biosynthesis, isopenthenyl pyrophosphate (IPP) and its isomer dimethylallyl pyrophosphate, are synthesized in this organism via the methylerythritol phosphate (MEP) or non-mevalonate pathway. Terminal pathway engineering in recombinant C. glutamicum permitted the production of various non-native C50 and C40 carotenoids. Here, the role of engineering isoprenoid precursor supply for lycopene production by C. glutamicum was characterized. Overexpression of dxs encoding the enzyme that catalyzes the first committed step of the MEP-pathway by chromosomal promoter exchange in a prophage-cured, genome-reduced C. glutamicum strain improved lycopene formation. Similarly, an increased IPP supply was achieved by chromosomal integration of two artificial operons comprising MEP pathway genes under the control of a constitutive promoter. Combined overexpression of dxs and the other six MEP pathways genes in C. glutamicum strain LYC3-MEP was not synergistic with respect to improving lycopene accumulation. Based on C. glutamicum strain LYC3-MEP, astaxanthin could be produced in the milligrams per gram cell dry weight range when the endogenous genes crtE, crtB, and crtI for conversion of geranylgeranyl pyrophosphate to lycopene were coexpressed with the genes for lycopene cyclase and β-carotene hydroxylase from Pantoea ananatis and carotene C(4) oxygenase from Brevundimonas aurantiaca.

Optimization of the IPP precursor supply for the production of lycopene, decaprenoxanthin and astaxanthin by Corynebacterium glutamicum

Directory of Open Access Journals (Sweden)

Sabine A.E. Heider

2014-08-01

Full Text Available The biotechnologically relevant bacterium C. glutamicum, currently used for the million ton-scale production of amino acids for the food and feed industries, is pigmented due to synthesis of the rare cyclic C50 carotenoid decaprenoxanthin and its glucosides. The precursors of carotenoid biosynthesis, isopenthenyl pyrophosphate (IPP and its isomer dimethylallyl pyrophosphate (DMAPP, are synthesized in this organism via the methylerythritol phosphate (MEP or non-mevalonate pathway. Terminal pathway engineering in recombinant C. glutamicum permitted the production of various nonnative C50 and C40 carotenoids. Here, the role of engineering isoprenoid precursor supply for lycopene production by C. glutamicum was characterized. Overexpression of dxs encoding the enzyme that catalyzes the first committed step of the MEP-pathway by chromosomal promoter exchange in a prophage-cured, genome-reduced C. glutamicum strain improved lycopene formation. Similarly, an increased IPP supply was achieved by chromosomal integration of two artificial operons comprising MEP pathway genes under the control of a constitutive promoter. Combined overexpression of dxs and the other six MEP pathways genes in C. glutamicum strain LYC3-MEP was not synergistic with respect to improving lycopene accumulation. Based on C. glutamicum strain LYC3-MEP astaxanthin could be produced in the mg per g cell dry weight range when the endogenous genes crtE, crtB and crtI for conversion of geranylgeranyl pyrophosphate to lycopene were coexpressed with the genes for lycopene cyclase and β-carotene hydroxylase from Pantoea ananatis and carotene C(4 oxygenase from Brevundimonas aurantiaca.

Improvement of the T-peel Strength of Polypropylene Adhesion Joints by Surface Photografting Pre-Treatment with Methyl Methacrylate

Science.gov (United States)

Balart, R.; Sánchez-Nácher, L.; Balart, J.; Fombuena, V.; España, J. M.

2010-06-01

Although polypropylene is one of the most used polymers at industrial level due to good balanced properties, it presents some restrictions in applications that require good adhesion properties as well as coating and painting. These restrictions are related to its non polar nature which leads to low wetting properties. So that, in most cases, it is necessary a previous surface pre-treatment in order to improve adhesion properties. These surface treatments could be physical or chemical. Among the wide variety of physical processes, plasma technologies are useful from both technical and environmental points of view. If we take into account economic considerations, chemical processes are interesting due to low cost equipment and procedures. In particular, we have used photografting of methyl methacrylate (MMA) monomer on polypropylene substrates with UV radiation and initiators. This process is useful to promote chemical modification of polypropylene surface by grafting MMA monomers into polypropylene polymer chains. Due to polarity of some groups in MMA monomers, it is possible to increase surface wettability thus promoting a remarkable increase in adhesion properties of polypropylene. In this work, changes in wettability of polypropylene surfaces in terms of the exposure time to UV radiation in presence of MMA monomers and initiators has been investigated. Furthermore, chemical changes have been characterized by FTIR analysis and mechanical performance of adhesion joints has been evaluated by T-peel tests.

Effect of Mesoporous Silica and Hydroxyapatite Nanoparticles on the Tensile and Dynamic Mechanical Thermal Properties of Polypropylene and Polypropylene Foam

Directory of Open Access Journals (Sweden)

Alireza Albooyeh

2014-12-01

Full Text Available The main purpose of this paper is the experimental study on the tensile and dynamic - mechanical thermal properties of polypropylene (PP and polypropylene foam reinforced with mesoporous silica (MCM-41, hydroxyapatite (HA and the composite of mesoporous silica and hydroxyapatite (MCM41-HA nanoparticles. Nanocomposites and nanocomposite foams containing PP, maleic anhydride grafted polypropylene, different nanoparticles and chemical blowing agent (for foam samples are mixed using the melt-compounding technique in a twin-screw extruder. The results of the tests show that at the same nanoparticles content, all the nanofillers cause better mechanical properties than neat PP and PP foam. Also, due to the porous structure of the foam samples, these samples have the higher damping characteristics and lower tensile properties than the solid samples. Because of higher rigidity and higher strength of HA nanoparticles, the greatest increase in modulus and tensile strength occurs by adding these nanoparticles to neat PP and PP foam. The highest damping factor is obtained by adding MCM-41-HA nanoparticles to PP and PP foam, because of the porous nature of the MCM-41 particles which were reinforced by HA particles. The results of differential scanning calorimetry show that the addition of different nanoparticles does not have any significant effect on crystallinity and melting behavior of PP. Scanning electron microscopy images show that the nanomaterials were fine and uniformly dispersed within the polymer matrix. Furthermore, the addition of different nanoparticles to PP foam causes to increase the cell density, to reduce the cell sizes and to improve the cell sizes distribution. In this respect, the lowest cell sizes and the highest cell density are created by adding HA and MCM41-HA  nanopaticles to PP foams.

Rheology of High-Melt-Strength Polypropylene for Additive Manufacturing

DEFF Research Database (Denmark)

Hofstätter, Thomas; Kamleitner, Florian; Jagenteufel, Ralf

Acrylonitrile butadiene styrene (ABS) is a widely used material for additive manufacturing (AM) fused deposition modeling (FDM). The rheological properties of high-melt-strength polypropylene (HMS-PP) were compared to commercially available ABS 250 filament to study the possibility of using...

Effect of boron and phosphate compounds on physical, mechanical, and fire properties of wood-polypropylene composites

Science.gov (United States)

Nadir Ayrilmis; Turgay Akbulut; Turker Dundar; Robert H. White; Fatih Mengeloglu; Umit Buyuksari; Zeki Candan; Erkan Avci

2012-01-01

Physical, mechanical, and fire properties of the injection-molded wood flour/polypropylene composites incorporated with different contents of boron compounds; borax/boric acid and zinc borate, and phosphate compounds; mono and diammonium phosphates were investigated. The effect of the coupling agent content, maleic anhydride-grafted polypropylene, on the properties of...

Fracture behavior of polypropylene/clay nanocomposites.

Science.gov (United States)

Chen, Ling; Wang, Ke; Kotaki, Masaya; Hu, Charmaine; He, Chaobin

2006-12-01

Polypropylene (PP)/clay nanocomposites have been prepared via a reactive compounding approach with an epoxy based masterbatch. Compared with PP and common PP/organoclay nanocomposites, the PP/clay nanocomposites based on epoxy/clay masterbatch have higher impact strength. The phenomenon can be attributed to the epoxy phase dispersed uniformly in the PP matrix, which may act as impact energy absorber and helps to form a large damage zone, thus a higher impact strength value is achieved.

Mechanisms of Contact Electrification at Aluminum-Polytetrafluoroethylene and Polypropylene-Water

KAUST Repository

Nauruzbayeva, Jamilya

2017-01-01

of electrons, but a comprehensive understanding of contact electrification at interfaces of electrical insulators, such as air, water, polytetrafluoroethylene (PTFE), polypropylene remains incomplete. In fact, a variety of mechanisms responsible for transfer

Laparoscopic sacrocolpopexy for recurrent pelvic organ prolapse after failed transvaginal polypropylene mesh surgery.

Science.gov (United States)

Schmid, Corina; O'Rourke, Peter; Maher, Christopher

2013-05-01

A prospective case series to assess the safety and efficacy of laparoscopic sacrocolpopexy for the surgical management of recurrent pelvic organ prolapse (POP) after transvaginal polypropylene mesh prolapse surgery. Between January and December 2010, women with post-hysterectomy recurrent prolapse (≥ stage 2 POP-Q) after transvaginal polypropylene mesh prolapse surgery were included. Perioperative morbidity and short-term complications were recorded and evaluated. Surgical outcomes were objectively assessed utilising the Pelvic Organ Prolapse Quantification system (POP-Q), the validated, condition-specific Australian Pelvic Floor Questionnaire (APFQ) and the Patient Global Impression of Improvement (PGI-I) at 12 months. All 16 women in this study had undergone surgery with trocar-guided transvaginal polypropylene mesh kits. In 75% the recurrent prolapse affected the compartment of prior mesh surgery with the anterior (81%) and apical (75%) compartment prolapse predominating. At a mean follow-up of 12 months, all women had resolution of awareness of prolapse, had transvaginal mesh surgery is feasible and safe. Further widespread evaluation is required.

Role of carbon nanotubes (CNTs) in improving wear properties of polypropylene (PP) in dry sliding condition

International Nuclear Information System (INIS)

Ashok Gandhi, R.; Palanikumar, K.; Ragunath, B.K.; Paulo Davim, J.

2013-01-01

Highlights: ► Role of carbon nanotubes (CNTs) on wear behaviour of polypropylene (PP) is evaluated. ► Effect of applied pressure and composition against a steel counter face is investigated. ► Microstructure and worn surfaces of samples are observed by scanning electron microscope. ► The wear phenomenon has been discussed based on wear losses and worn surfaces. ► The coefficient of friction (μ) and sliding time for PP and PP/CNT blend is investigated. - Abstract: Polymers are widely used for sliding couples against metals and other materials. Polypropylene is a polymer used in variety of applications includes packaging, laboratory equipments, automotive components, etc. Polypropylene is often desirable automotive material due to its low cost, colorability, chemical resistance and UV stability. In addition the range of potential polypropylene uses is nearly unlimited through the use of modifiers, additives and fillers. In the present work, the sliding wear of polypropylene (PP) and carbon nanotube (CNT) blends are evaluated as a function of applied load and composition against a steel counter face in dry condition. The addition of CNT in PP in wear performance is investigated and presented in detail. Microstructure and worn surfaces of samples were observed by scanning electron microscope. The wear phenomenon has been discussed based on wear losses and worn surfaces

Dynamics of fibrillar precursors of shishes as a function of stress

Energy Technology Data Exchange (ETDEWEB)

Balzano, Luigi; Cavallo, Dario; Van Erp, Tim B; Ma Zhe; Housmans, Jan-Willem; Fernandez-Ballester, Lucia; Peters, Gerrit W M, E-mail: G.W.M.Peters@tue.n

2010-11-15

Shishes are fibrillar crystallites that can be created by deforming a polymer melt. The formation of shishes takes place when flow is strong enough to stretch molecules. In the early stages, bundles of stretched molecules with pre-crystalline order form metastable precursors whose stability depends on their size and, hence, on the stress level. We find that for a specific isotactic polypropylene, close to the nominal melting point, a stress larger than 0.10 MPa leads to stable fibrillar precursors that are partially crystalline immediately after flow. On the other hand, below 0.10 MPa, the aspect ratio of precursors tends to unity and the lack of crystallinity makes these structures prone to dissolution.

Enhancing the Dyeability of Polypropylene Fibers by Melt Blending with Polyethylene Terephthalate

Directory of Open Access Journals (Sweden)

Fereshteh Mirjalili

2013-01-01

Full Text Available Attempts were made to modify polypropylene fibers by melt blending with polyethylene terephthalate in order to enhance the dyeability of the resultant fiber. Five blends of polypropylene/polyethylene terephthalate/compatibilizer were prepared and subsequently spun into fibers. Three disperse dyes were used to dye such modified fibers at boiling and 130°C. The dyeing performance of the blend fibers, as well as the morphological, chemical, thermal, and mechanical properties, of the corresponding blends was characterized by means of spectrophotometry, polarized optical microscopy, scanning electron microscopy (SEM, FT-IR spectroscopy, differential scanning calorimetry (DSC, and tensile testing.

Evaluation of Properties of Unidirectional Hemp/Polypropylene Composites: Influence of Fiber Content and Fiber/Matrix Interface Variables

DEFF Research Database (Denmark)

Plackett, David; Løgstrup Andersen, Tom; Lilholt, Hans

2002-01-01

Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites.......Flament-wound textile hemp yarn was used in combination with unmodified or maleated polypropylene (PP) films to produce plates of unidirectional composites....

Properties of Recycled Aggregate Concrete Reinforced with Polypropylene Fibre

Directory of Open Access Journals (Sweden)

Wan Mohammad Wan Nur Syazwani

2016-01-01

Full Text Available This research work is aimed to investigate how the addition of various proportion of polypropylene fibre affects the mechanical strength and permeability characteristics of recycled aggregate concrete (RAC which has been produced with treated coarse recycled concrete aggregate (RCA. Further research on RAC properties and their applications is of great importance as the scarcity of virgin aggregate sources in close proximity to major urban centers is becoming a worldwide problem. In this study, the hardened RAC properties at the curing age of 7 and 28 days such as compressive strength, flexural strength, ultrasonic pulse velocity (UPV, water absorption and total porosity were evaluated and compare with control specimens. Experimental result indicates that although the inclusion of the treated coarse RCA can enhance the mechanical strength and permeability properties of RAC, Further modification by addition of polypropylene fibre can optimize the results.

Polypropylene Darning: A New Alternative for Reconstruction of Orbital Floor after Total Maxillectomy.

Science.gov (United States)

Sharma, Prashant

2015-06-01

Removal of orbital floor is an integral part of total (radical) maxillectomy (type IIIa), which if not managed properly, may lead to some eye related distressing complications like diplopia, eyelid malposition, epiphora, dacryocystitis, enopthalmos and ectoprion. Among all, diplopia is the most distressing complication which hampers daily activity. Various options for orbital floor reconstruction are available like titanium sheet, polypropylene mesh, non-vascularized or vascularized bone graft, pedicled flaps, micro-vascular free flaps, prosthesis placement, and split skin graft followed by obturator placement. Till date no-body has tried stabilization of eye ball by 'darning' the orbital floor using non-absorbable suture. 'Polypropylene suture darning' is an easy to learn, novel method with equally good results. Five patients with potentially resectable tumors underwent total maxillectomy. I used polypropylene 3-0 round body suture and 'darning' was done at orbital floor, incorporating periosteum (if remaining) and peri-orbital fat into the sutures. Muscle flaps were done to provide bulk and palatal reconstruction. Assessment of patients was done post-operatively at day-5 i.e., before discharge and at 1 month after surgery, and also in further follow up visits. The results were very good in terms of clear vision & eye movements (directly related to 'darning'), and the aesthetic look of patients and bilateral symmetry were satisfactory (not related to darning). Darning of orbital floor by polypropylene after total maxillectomy is an easy to learn and cost-effective method of reconstruction with good results.

Effect of Surface Modification of Palygorskite on the Properties of Polypropylene/Polypropylene-g-Maleic Anhydride/Palygorskite Nanocomposites

Directory of Open Access Journals (Sweden)

David Cisneros-Rosado

2017-01-01

Full Text Available The effect of surface modification of palygorskite (Pal on filler dispersion and on the mechanical and thermal properties of polypropylene (PP/polypropylene grafted maleic anhydride (PP-g-MAH/palygorskite (Pal nanocomposites was evaluated. A natural Pal mineral was purified and individually surface modified with hexadecyl tributyl phosphonium bromide and (3-Aminopropyltrimethoxysilane; the pristine and modified Pals were melt-compounded with PP to produce nanocomposites using PP-g-MAH as compatibilizer. The grafting of Pal surface was verified by FT-IR and the change in surface hydrophilicity was estimated by the contact angle of sessile drops of ethylene glycol on Pal tablets. The extent of Pal dispersion and the degree of improvement in both the mechanical and thermal properties were related to the surface treatment of Pal. Modified Pals were better dispersed during melt processing and improved Young’s modulus and strength; however, maximum deformation tended to decrease. The thermal stability of PP/PP-g-MAH/Pal nanocomposites was considerably improved with the content of modified Pals. The degree of crystallinity increased with Pal content, regardless of the surface modification. Surfactant modified Pal exhibited better results in comparison with silane Pal; it is possible that longer alkyl chains from surfactant molecules promoted interactions with polymer chains, thereby improving nanofiller dispersion and enhancing the properties.

Implementing New Methods of Laser Marking of Items in the Nuclear Material Control and Accountability System at SSC RF-IPPE: An Automated Laser Marking System

International Nuclear Information System (INIS)

Regoushevsky, V.I.; Tambovtsev, S.D.; Dvukhsherstnov, V.G.; Efimenko, V.F.; Ilyantsev, A.I.; Russ, G.P. III

2009-01-01

For over ten years SSC RF-IPPE, together with the US DOE National Laboratories, has been working on implementing automated control and accountability methods for nuclear materials and other items. Initial efforts to use adhesive bar codes or ones printed (painted) onto metal revealed that these methods were inconvenient and lacked durability under operational conditions. For NM disk applications in critical stands, there is the additional requirement that labels not affect the neutron characteristics of the critical assembly. This is particularly true for the many stainless-steel clad disks containing highly enriched uranium (HEU) and plutonium that are used at SSC RF-IPPE for modeling nuclear power reactors. In search of an alternate method for labeling these disks, we tested several technological options, including laser marking and two-dimensional codes. As a result, the method of laser coloring was chosen in combination with Data Matrix ECC200 symbology. To implement laser marking procedures for the HEU disks and meet all the nuclear material (NM) handling standards and rules, IPPE staff, with U.S. technical and financial support, implemented an automated laser marking system; there are also specially developed procedures for NM movements during laser marking. For the laser marking station, a Zenith 10F system by Telesis Technologies (10 watt Ytterbium Fiber Laser and Merlin software) is used. The presentation includes a flowchart for the automated system and a list of specially developed procedures with comments. Among other things, approaches are discussed for human-factor considerations. To date, markings have been applied to numerous steel-clad HEU disks, and the work continues. In the future this method is expected to be applied to other MC and A items.

Coir dust reinforced recycled polypropylene composites; Compositos de polipropileno reciclado e po de coco

Energy Technology Data Exchange (ETDEWEB)

Santos, Bianca B. dos; Costa, Marysilvia F. da; Thire, Rossana M. da S.M., E-mail: bianca@metalmat.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil)

2015-07-01

The environmental impacts caused by disposed plastics encourage the search for new alternatives. Recycling polymers leads to the degradation of their mechanical properties, which can be modified by the addition of fillers. In this paper, recycled polypropylene from plastic cups with 2%, 5% and 10% of coir dust were produced with and without the addition of additives. These composites were characterized by tensile tests, X-ray diffraction, differential scanning calorimetry and scanning electron microscopy on the fracture surface. It was verified the effectiveness of the addition of coir dust in improving the elasticity modulus of recycled polypropylene besides the effectiveness of additives used in promoting the adhesion of the powder to the matrix. However, higher levels of coir dust caused the appearance of air bubbles inside the material, which contributed to its embrittlement. The addition of coir dust promoted a decrease in the degree of polypropylene crystallinity. (author)

Storing of Extracts in Polypropylene Microcentrifuge Tubes Yields Contaminant Peak During Ultra-flow Liquid Chromatographic Analysis.

Science.gov (United States)

Kshirsagar, Parthraj R; Hegde, Harsha; Pai, Sandeep R

2016-05-01

This study was designed to understand the effect of storage in polypropylene microcentrifuge tubes and glass vials during ultra-flow liquid chromatographic (UFLC) analysis. One ml of methanol was placed in polypropylene microcentrifuge tubes (PP material, Autoclavable) and glass vials (Borosilicate) separately for 1, 2, 4, 8, 10, 20, 40, and 80 days intervals stored at -4°C. Contaminant peak was detected in methanol stored in polypropylene microcentrifuge tubes using UFLC analysis. The contaminant peak detected was prominent, sharp detectable at 9.176 ± 0.138 min on a Waters 250-4.6 mm, 4 μ, Nova-Pak C18 column with mobile phase consisting of methanol:water (70:30). It was evident from the study that long-term storage of biological samples prepared using methanol in polypropylene microcentrifuge tubes produce contaminant peak. Further, this may mislead in future reporting an unnatural compound by researchers. Long-term storage of biological samples prepared using methanol in polypropylene microcentrifuge tubes produce contaminant peakContamination peak with higher area under the curve (609993) was obtained in ultra-flow liquid chromatographic run for methanol stored in PP microcentrifuge tubesContamination peak was detected at retention time 9.113 min with a lambda max of 220.38 nm and 300 mAU intensity on the given chromatographic conditionsGlass vials serve better option over PP microcentrifuge tubes for storing biological samples. Abbreviations used: UFLC: Ultra Flow Liquid Chromatography; LC: Liquid Chromatography; MS: Mass spectrometry; AUC: Area Under Curve.

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

Energy Technology Data Exchange (ETDEWEB)

Das, Oisik [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Bhattacharyya, Debes [Department of Mechanical Engineering, Center for Advanced Composite Materials, University of Auckland, Auckland 1142 (New Zealand)

2015-04-15

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications.

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

International Nuclear Information System (INIS)

Das, Oisik; Sarmah, Ajit K.; Bhattacharyya, Debes

2015-01-01

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications

Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

Directory of Open Access Journals (Sweden)

Yongjoo Kim

2013-01-01

Full Text Available This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of the fiber and the other mixtures, which included the conventional recycled foamed asphalt (RFA mixtures; the cement reinforced recycled foamed asphalt (CRFA mixtures; the semihot recycled foamed asphalt (SRFA mixtures; and recycled hot-mix asphalt (RHMA mixtures. It is found that the FRFA mixture shows higher Marshall stability than the RFA and SRFA mixtures, higher indirect tensile strength than the RFA mixture, and higher rut resistance than the RFA, SRFA, and RHMA mixtures as seen from the wheel tracking test.

Thermal analysis of polypropylene modified by gamma irradiation composites under outdoor conditions

International Nuclear Information System (INIS)

Komatsu, Luiz G.H.; Oliani, Washington L.; Lugao, Ademar B.; Parra, Duclerc F.

2015-01-01

This work reports the influence of the clay in the degradation process of the HMSPP.The polypropylene (PP) was irradiated under acetylene atmosphere in gamma irradiation source ( 60 Co) to obtain the HMSPP (high melt strength polypropylene). Composites of HMSPP were processed in twin-screw extruder with clay Cloisite 20A and Maleic Anhydride (PP-g-MA) as coupling agent. The obtained composites were exposed under outdoor conditions for 6 months. The ageing effects were characterized by Differential Scanning Calorimetry (DSC), Thermogravimetry Analysis (TGA). Chemical oxidation was evaluated by Carbonyl Index (IC) through infrared Spectroscopy (FT-IR). The results showed correlation between carbonyl index and ageing time. (author)

Thermal analysis of polypropylene modified by gamma irradiation composites under outdoor conditions

Energy Technology Data Exchange (ETDEWEB)

Komatsu, Luiz G.H.; Oliani, Washington L.; Lugao, Ademar B.; Parra, Duclerc F., E-mail: dfparra@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

This work reports the influence of the clay in the degradation process of the HMSPP.The polypropylene (PP) was irradiated under acetylene atmosphere in gamma irradiation source ({sup 60}Co) to obtain the HMSPP (high melt strength polypropylene). Composites of HMSPP were processed in twin-screw extruder with clay Cloisite 20A and Maleic Anhydride (PP-g-MA) as coupling agent. The obtained composites were exposed under outdoor conditions for 6 months. The ageing effects were characterized by Differential Scanning Calorimetry (DSC), Thermogravimetry Analysis (TGA). Chemical oxidation was evaluated by Carbonyl Index (IC) through infrared Spectroscopy (FT-IR). The results showed correlation between carbonyl index and ageing time. (author)

Surgical treatment of subcostal incisional hernia with polypropylene mesh - analysis of late results

Directory of Open Access Journals (Sweden)

Marco Antonio de Oliveira Peres

Full Text Available OBJECTIVE: To evaluate the results of subcostal incisional hernia repair using polypropylene mesh, the technical aspects of musculo-aponeurotic reconstruction, routine fixation of supra-aponeurotic mesh and follow-up for five years.METHODS: We conducted a retrospective study that assessed 24 patients undergoing subcostal incisional hernia repair with use of polypropylene mesh; 15 patients (62.5% were female; ages ranged from 33 to 82, and 79.1% had comorbidities.RESULTS: Early complications: three cases (12.5% of wound infection, three cases (12.5% of seroma, one case (4.1% of hematoma; and one case (4.1% of wound dehiscence. Late complications occurred in one case (4.1% of hernia recurrence attributed to technical failure in the fixation of the mesh and in one case (4.1% of chronic pain. There were no cases of exposure or rejection of the mesh.CONCLUSION: The subcostal incisional hernia, though not very relevant, requires adequate surgical treatment. Its surgical correction involves rebuilding the muscle-aponeurotic defect, supra-aponeurotic fixation of polypropylene mesh, with less complexity and lower rates of complications and recurrences.

Nickel-titanium wire in circumferential suture of a flexor tendon repair: a comparison to polypropylene.

Science.gov (United States)

Karjalainen, T; He, M; Chong, A K S; Lim, A Y T; Ryhanen, J

2010-07-01

Nickel-titanium (NiTi) has been proposed as an alternative material for flexor tendon core suture. To our knowledge, its suitability as a circumferential suture of flexor tendon repair has not been investigated before. The purpose of this ex vivo study was to investigate the biomechanical properties of NiTi circumferential repairs and to compare them with commonly used polypropylene. Forty porcine flexor tendons were cut and repaired by simple running or interlocking mattress technique using 100 microm NiTi wire or 6-0 polypropylene. The NiTi circumferential repairs showed superior stiffness, gap resistance, and load to failure when compared to polypropylene repairs with both techniques. Nickel-titanium wire seems to be a potential material for circumferential repair of flexor tendons. Copyright 2010 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Process monitoring of glass reinforced polypropylene laminates using fiber Bragg gratings

KAUST Repository

Mulle, Matthieu; Wafai, Husam; Yudhanto, Arief; Lubineau, Gilles; Yaldiz, R.; Schijve, W.; Verghese, N.

2015-01-01

Hot-press molding of glass-fiber-reinforced polypropylene (GFPP) laminates was monitored using longitudinally and transversely embedded fiber Bragg gratings (FBGs) at different locations in unidirectional laminates. The optical sensors proved

Use of polypropylene mesh in hernioplasty by Lichtenstein's technique

International Nuclear Information System (INIS)

Montejo Sainz, Jesus Enrique; Pisonero Socias, Juan Jose

2011-01-01

INTRODUCTION. The aim of present study was to assess the benefit using the prosthesis (polypropylene mesh) in the hernioplasty using the Lichtenstein's technique in the 'Joaquin Albarran' Clinical Surgical Hospital. METHODS. A prospective study (with an interval of 14 months) was conducted in 140 surgical interventions carried out using the Lichtenstein's technique in patients presenting with inguinal hernia. One hundred and ten patients were excluded due to interventions were of ambulatory method. The following data were studied: type of hernia found in the physical examination, age, sex, and race, type of job, intervention's date, and technique used as well as the complications during the immediate postoperative time. Also, the hernia's relapse after operation, surgical complications and tolerance to polypropylene mesh were taking into account. RESULTS. There was predominance of male sex confirming a direct influence among types of jobs requiring a strong physical effort and the appearance of inguinal hernias (63,3 %). There were only three complications: a hematoma and two seromas. There were not relapses and any case of infection, both local and systemic. The use of prophylactic antibiotics showed an appropriate cost-benefit relationship. CONCLUSIONS. The old age, the male sex and a sustained physical effort have a directly proportional relation to appearance of inguinal hernias. The feasibility of Lichtenstein's hernioplasty, the null incidence of hernia relapses and no appearance of complications including the rejection to prosthetic material, favoured the use of polypropylene in this plasty. Authors recommended the use of perioperative prophylactic antibiotic therapy to avoid wound's infection and thus to secure the result of surgical intervention and its durability. (author)

Development of bio/blood compatible polypropylene through low pressure nitrogen plasma surface modification

International Nuclear Information System (INIS)

Gomathi, N.; Rajasekar, R.; Babu, R. Rajesh; Mishra, Debasish; Neogi, S.

2012-01-01

Surface modification of polypropylene by nitrogen containing plasma was performed in this work in order to improve the wettability which resulted in enhanced biocompatibility and blood compatibility. Various nitrogen containing functional groups as well as oxygen containing functional groups were found to be incorporated to the polymer surface during plasma treatment and post plasma reaction respectively. Wettability of the polymers was evaluated by static contact angle measurement to show the improvement in hydrophilicity of plasma treated polypropylene. Cross linking and surface modification were reported to be dominating in the case of nitrogen plasma treatment compared to degradation. The effect of various process variables namely power, pressure, flow rate and treatment time on surface energy and weight loss was studied at various levels according to the central composite design of response surface methodology (RSM). Except pressure the other variables resulted in increased weight loss due to etching whereas with increasing pressure weight loss was found to increase and then decrease. The effect of process variables on surface morphology of polymers was evaluated by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Well spread fibroblast cells on nitrogen plasma treated polypropylene due to the presence of CO, NH 2+ and NH + was observed. Reduced platelet adhesion and increased partial thromboplastin time evidenced the increased blood compatibility. - Highlights: ► Improved biocompatibility and blood compatibility of polypropylene. ► Nitrogen plasma surface modification. ► Maintaining a balance between polar group incorporation and weight loss due to etching. ► Optimization of process conditions by response surface methodology.

Influence of E-beam irradiation on dielectric relaxation of recycled polypropylene

International Nuclear Information System (INIS)

Fazilova, Z.; Gafurov, U.; Tolstov, A.

2004-01-01

Full text: The dielectric relaxation connected with molecular groups and polymer chain mobility for un-irradiated and e-beam irradiated recycled polypropylene was investigated. It was studied films of samples produced from virgin (initial) and e- beam irradiated of the polymer granules (E-beam source with 5 MeV energy). The dielectric losses were measured with temperature increasing and decreasing regime. The losses were measured with E8-4 bridge help (the frequency is 1kH). Heating velocity was 2 grad/min. The dielectric losses did not appeared in minus temperature region for the initial polypropylene samples. The measurement in temperature increasing and decreasing shows that the relaxation peak at ∼ 35 o C for un-irradiated and ∼70 o C for irradiated polymer samples connected with macromolecular segments mobility with water molecular groups participation. The main relaxation peak (higher 100 o C) shifts after e-beam irradiation is result of the cross-links formation. ) The peak connected with macromolecular segments mobility in polymer amorphous regions (β-relaxation process). In irradiated polypropylene on IR spectroscopy data oxygen molecular groups is increased. The molecular groupings form inter-molecular hydrogen bonds. The intermolecular bonds also hindered molecular groups and macromolecular mobility. The e-beam stimulated cross-links formation was confirmed by method of sol-gel analyses. The work was supported by STCU Fund (Project No 3009)

Historical records of the electric power and cooling water systems for the experimental facilities in the I.P.P. (1964-1983)

International Nuclear Information System (INIS)

Kitajima, Miyoshi.

1984-01-01

Twenty years have passed, since experimental studies began in the IPP. This is a status report on the electric power and cooling water systems in this Institute. Historical records on consumption of the electric power and cooling water for experimental facilities are summarized, also. Valuable stories obtained through operation, control and periodic inspection of these systems are described, which will be helpful for construction of new systems in future. Finally problems on safety, reliability, and economy are commented. (author)

EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA); Scientific Opinion on the substantiation of a health claim related to isoleucyl-prolyl-proline (IPP) and valyl-prolyl-proline (VPP) and maintenance of normal blood pressure pursuant to Article 13(5) of Regulation (EC) No 1924/2006

DEFF Research Database (Denmark)

Tetens, Inge

to isoleucyl-prolyl-proline (IPP) and valyl-prolyl-proline (VPP) and maintenance of normal blood pressure (BP). The tripeptides IPP and VPP are sufficiently characterised. Maintenance of normal blood pressure is a beneficial physiological effect. The applicant identified a total of 20 published intervention......Following an application from Valio Ltd submitted pursuant to Article 13(5) of Regulation (EC) No 1924/2006 via the Competent Authority of Finland, the Panel on Dietetic Products, Nutrition and Allergies was asked to deliver an opinion on the scientific substantiation of a health claim related...... relationship has not been established between the consumption of IPP and VPP and maintenance of normal blood pressure. © European Food Safety Authority, 2011...

Mechanisms of Contact Electrification at Aluminum-Polytetrafluoroethylene and Polypropylene-Water

KAUST Repository

Nauruzbayeva, Jamilya

2017-04-01

Contact electrification refers to the transfer of electrical charges between two surfaces, similar and dissimilar, as they are brought into contact and separated; this phenomenon is also known as static electrification or triboelectrification. For example, everyone has experienced weak electrical shocks from metal doorknobs, wool and synthetic clothing on dry days. While contact electrification might appear insignificant, it plays a key role in numerous natural and industrial processes, including atmospheric lightning, accumulation of dust on solar panels, charging of liquids during pipetting and flow in the tubes, and fire hazards in granular media. Contact electrification at metal-metal interfaces is well understood in terms of transfer of electrons, but a comprehensive understanding of contact electrification at interfaces of electrical insulators, such as air, water, polytetrafluoroethylene (PTFE), polypropylene remains incomplete. In fact, a variety of mechanisms responsible for transfer of electrical charges during mechanical rubbing, slipping, sliding, or flow at interfaces have been proposed via: electrons, ions, protons, hydroxide ions from water, specific orientation of dipoles, mechanoradicals, cryptoelectrons, and transfer of material. We have noticed that the extent of contact electrification of solids in water is influenced by surface free energies, mobile ions, surface roughness, duration of contact, sliding speeds, and relative humidity. Herein, we present results of our experimental investigation of contact electrification at the following interfaces: (i) PTFE-aluminum in air and (ii) polypropylene-water interfaces. To identify the underlying mechanism, we started with various hypotheses and exploited a variety of experimental techniques to falsify most of them until we got an answer; our techniques included high-voltage power supply (0-10,000 V), Faraday cages, Kelvin probe force microscopy, electrodeposition, X-ray photoelectron spectroscopy

Packing parameters effect on injection molding of polypropylene nanostructured surfaces

DEFF Research Database (Denmark)

Calaon, Matteo; Tosello, Guido; Hansen, Hans Nørgaard

2012-01-01

having a diameter of 500 nm was employed. The tool insert surface was produced using chemical-based-batch techniques such aluminum anodization and nickel electroplating. During the injection molding process, polypropylene (PP) was employed as material and packing phase parameters (packing time, packing...

Interfacial interactions of poly(urethane-urea) based primers with polypropylene

NARCIS (Netherlands)

Villani, M.; Scheerder, J. (Jeroen); Benthem, van R.A.T.M.; With, de G.

2014-01-01

Good adhesion to polypropylene is required in a number of technologies including printing, painting and food packaging technology. However, for good adhesion between polyolefins and other materials it is usually necessary to pretreat and prime the polyolefinic substrate. In this paper waterborne

Modelling of Creep and Stress Relaxation Test of a Polypropylene Microfibre by Using Fraction-Exponential Kernel

Directory of Open Access Journals (Sweden)

Andrea Sorzia

2016-01-01

Full Text Available A tensile test until breakage and a creep and relaxation test on a polypropylene fibre are carried out and the resulting creep and stress relaxation curves are fit by a model adopting a fraction-exponential kernel in the viscoelastic operator. The models using fraction-exponential functions are simpler than the complex ones obtained from combination of dashpots and springs and, furthermore, are suitable for fitting experimental data with good approximation allowing, at the same time, obtaining inverse Laplace transform in closed form. Therefore, the viscoelastic response of polypropylene fibres can be modelled straightforwardly through analytical methods. Addition of polypropylene fibres greatly improves the tensile strength of composite materials with concrete matrix. The proposed analytical model can be employed for simulating the mechanical behaviour of composite materials with embedded viscoelastic fibres.

Comparative Study Of The Preparation Of Maleic Anhydride-g-Polypropylene By Two Grafting Processes Using Peroxide

International Nuclear Information System (INIS)

Sakahara, R.M.; Wang, S.H.

2010-01-01

The Polypropylene grafting with Maleic anhydride is a thoroughly known technique. Its wide application is due, mainly,to the controlled changing in the polarity of this polymer, which increases the interfacial adhesion in blends and compounds. In this study, two grafting processes were compared. In the first, the maleic anhydride was grafted on polypropylene in a solution batch process, carried out in a round-bottom vessel. The second approach was carried out by reactive extrusion of polypropylene in the presence of peroxide and maleic anhydride. The samples thus prepared were characterized by DSC, TGA, FTIR, WAXS, EDS e SEM. It was possible to conclude that the solution technique was more efficient than the reactive extrusion; however the later was easier to accomplish due to the high viscosity of PP. (author)

Characterizing and modeling the pressure- and rate-dependent elastic-plastic-damage behaviors of polypropylene-based polymers

KAUST Repository

Pulungan, Ditho Ardiansyah

2018-02-24

Polymers in general exhibit pressure- and rate-dependent behavior. Modeling such behavior requires extensive, costly and time-consuming experimental work. Common simplifications may lead to severe inaccuracy when using the model for predicting the failure of structures. Here, we propose a viscoelastic viscoplastic damage model for polypropylene-based polymers. Such a set of constitutive equations can be used to describe the response of polypropylene under various strain-rates and stress-triaxiality conditions. Our model can also be applied to a broad range of thermoplastic polymers. We detail the experimental campaign that is needed to identify every parameter of the model at best. We validated the proposed model by performing 3-point bending tests at different loading speeds, where the load-displacement response of polypropylene beam up to failure was accurately predicted.

Assessment of extrusion-sonication process on flame retardant polypropylene by rheological characterization

Directory of Open Access Journals (Sweden)

Guadalupe Sanchez-Olivares

2016-05-01

Full Text Available In this work, the rheological behavior of flame retardant polypropylene composites produced by two methods: 1 twin-screw extrusion and 2 ultrasound application combined with a static mixer die single-screw extrusion is analyzed in detail; results are related to the morphology of the composites. The flame retardant polymer composites are composed of a polypropylene matrix, an intumescent flame retardant system and functionalized clay. Scanning electron microscopy revealed that the combination of the static mixer die and on-line sonication reduced particle size and improved the dispersion and distribution of the intumescent additives in the polypropylene matrix at the micrometric level. From linear viscoelastic properties, the Han, Cole-Cole and van Gurp-Palmen diagrams characterized the improved particle dispersion of the flame retardant additives. Two well-defined rheological behaviors were observed in these diagrams. These behaviors are independent on clay presence and concentration. In fact, the ultrasound device generates a 3D highly interconnected structure similar to a co-continuous pattern observed in polymer blends as evidenced by rheological measurements. This improvement in the dispersion and distribution of the additives is attributed to the combined effect of the static mixer die and on-line sonication that allowed reducing the additive content while achieving the optimum classification UL94-V0.

Kenaf Fibre Reinforced Polypropylene Composites: Effect of Cyclic Immersion on Tensile Properties

Directory of Open Access Journals (Sweden)

W. H. Haniffah

2015-01-01

Full Text Available This research studied the degradation of tensile properties of kenaf fibre reinforced polypropylene composites due to cyclic immersion into two different solutions, as well as comparison of the developed composites’ tensile properties under continuous and cyclic immersion. Composites with 40% and 60% fibre loadings were immersed in tap water and bleach for 4 cycles. Each cycle consisted of 3 days of immersion and 4 days of conditioning in room temperature (28°C and 55% humidity. The tensile strength and modulus of composites were affected by fibre composition, type of liquid of immersion, and number of cycles. The number of immersion cycles and conditioning caused degradation to tensile strength and modulus of kenaf fibre reinforced polypropylene composites. Continuous and cyclic immersion in bleach caused tensile strength of the composites to differ significantly whereas, for tensile modulus, the difference was insignificant in any immersion and fibre loadings. However, continuous immersion in the bleach reduced the tensile strength of composites more compared to cyclic immersion. These preliminary results suggest further evaluation of the suitability of kenaf fibre reinforced polypropylene composites for potential bathroom application where the composites will be exposed to water/liquid in cyclic manner due to discontinuous usage of bathroom.

Synthesis and characterization of CNTs using polypropylene waste as precursor

Energy Technology Data Exchange (ETDEWEB)

Bajad, Ganesh S. [Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur 440010 (India); Tiwari, Saurabh K. [Department of Chemical Engineering, Indian Institute of Technology Bombay, Powai, Mumbai 400076 (India); Vijayakumar, R.P., E-mail: vijayakumarrp@che.vnit.ac.in [Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur 440010 (India)

2015-04-15

Graphical abstract: - Highlights: • A facile method for producing CNTs from polypropylene waste is proposed. • Optimization of Ni/Mo mole ratio using RSM suggests the adequacy of cubic model. • Process parameters were optimized by RSM using Box–Behnken four factorial design. • Maximum desirability of one suggested that 514% of CNTs would yield over Ni{sub 4}Mo{sub 0.2}MgO{sub 1}. • Increase in Ni/Mo ratio from 0.5 to 20, inner diameter of CNTs decreases from 25 to 2 nm. - Abstract: We study the synthesis of MWCNTs using polypropylene waste as a precursor and Ni/Mo/MgO as a catalyst by the combustion technique. Molar ratios of Ni, Mo and MgO in the Ni/Mo/MgO catalyst were optimized using response surface methodology (RSM) to obtain the maximum yield of CNTs. The mole ratio 4/0.2/1 was found to yield more carbon product. Further, process parameters such as combustion temperature, combustion time, polymer and catalyst weight were optimized by RSM using Box–Behnken three-level and four-factorial design. The best possible combination of process parameters (combustion time of 10 min, combustion temperature of 800 °C, polymer weight of 5 g and catalyst weight of 150 mg) for maximum yield of CNTs was obtained. HRTEM indicates that the diameter of CNTs depends on the catalyst composition used for the synthesis of CNTs. The results of the study indicate a facile method for producing CNTs from polypropylene waste.

Synthesis and characterization of CNTs using polypropylene waste as precursor

International Nuclear Information System (INIS)

Bajad, Ganesh S.; Tiwari, Saurabh K.; Vijayakumar, R.P.

2015-01-01

Graphical abstract: - Highlights: • A facile method for producing CNTs from polypropylene waste is proposed. • Optimization of Ni/Mo mole ratio using RSM suggests the adequacy of cubic model. • Process parameters were optimized by RSM using Box–Behnken four factorial design. • Maximum desirability of one suggested that 514% of CNTs would yield over Ni 4 Mo 0.2 MgO 1 . • Increase in Ni/Mo ratio from 0.5 to 20, inner diameter of CNTs decreases from 25 to 2 nm. - Abstract: We study the synthesis of MWCNTs using polypropylene waste as a precursor and Ni/Mo/MgO as a catalyst by the combustion technique. Molar ratios of Ni, Mo and MgO in the Ni/Mo/MgO catalyst were optimized using response surface methodology (RSM) to obtain the maximum yield of CNTs. The mole ratio 4/0.2/1 was found to yield more carbon product. Further, process parameters such as combustion temperature, combustion time, polymer and catalyst weight were optimized by RSM using Box–Behnken three-level and four-factorial design. The best possible combination of process parameters (combustion time of 10 min, combustion temperature of 800 °C, polymer weight of 5 g and catalyst weight of 150 mg) for maximum yield of CNTs was obtained. HRTEM indicates that the diameter of CNTs depends on the catalyst composition used for the synthesis of CNTs. The results of the study indicate a facile method for producing CNTs from polypropylene waste

Charge distribution and stability in electret materials

DEFF Research Database (Denmark)

Thyssen, Anders

The objective of the work presented in this Ph.D. thesis is to give a broader understanding of which key parameters influence the charge stability of polymer electrets, and how the electrical charges are distributed. This has been achieved using polypropylene as an electret polymer model system......-PP and i-PP, is because the charge retention is extremely sensitive to the sample preparation. This was seen in regard to the thermal history of the samples and the influence of micron and nano size particles in the polymer electret. Through adding micron and nano size calcium carbonate and aluminium oxide....... By means of kinetic rate theory the discharge behaviour could be explained for polypropylene when thermally stimulated. This resulted in the determination of several activation energies, which could be used for describing the discharging seen at isothermal conditions. This theory is a powerful tool...

The influence of antioxidant on positron annihilation in polypropylene

International Nuclear Information System (INIS)

Djourelov, N.; He, C.; Suzuki, T.; Ito, Y; Kondo, K.; Ito, Y.; Shantarovich, V.P.

2003-01-01

The purpose of this report is to check the influence of the carbonyl groups (CG), created by oxygen naturally dissolved in a polymer matrix and by the source irradiation, on annihilation characteristics of free positrons using the positron annihilation lifetime spectroscopy (PALS) and coincidence Doppler-broadening spectroscopy (CDBS). Positron annihilation in a pure polypropylene (PP) and in an antioxidant-containing polypropylene (PPA) sample at room and low temperatures has been studied by CDBS. PALS has been used as an o-Ps (orth-positronium) formation monitor. The momentum density distributions of electrons obtained by CDBS at the beginning of measurements have been compared to that at the o-Ps intensity saturation level. It has been shown that the initial concentration of carbonyl groups in a PP sample is high, while for an antioxidant-containing sample, PPA, carbonyl groups are not detected by CDBS. CDBS spectra for a PP can be explained by annihilation of free positrons with the oxygen contained in the carbonyl groups. For a PPA sample, no significant contribution of annihilation with oxygen core electrons can be concluded. (Y. Kazumata)

Acoustic properties of polypropylene composites reinforced with stone groundwood

Directory of Open Access Journals (Sweden)

Joan Pere López

2012-11-01

Full Text Available Currently, acoustic isolation is one of the problems raised with building construction in Spain. The publication of the Basic Document for the protection against noise of the Technical Building Code has increased the demand of comfort for citizens. This has created the need to seek new composite materials that meet the new required acoustical building codes. In this paper we report the results of the newly developed composites that are able to improve the acoustic isolation of airborne noise. These composites were prepared from polypropylene (PP reinforced with mechanical pulp fibers from softwood (Pinus radiata. Mechanical and acoustical properties of the composites from mechanical pulp (MP and polypropylene (PP have been investigated and compared to fiberglass (FG composites. MP composites had lower tensile properties compared with FG composites, although these properties can be improved by incorporation of a coupling agent. The results of acoustical properties of MP composites were reported and compared with the conventional composites based on fiberglass and gypsum plasterboards. Finally, we suggest the application of MP composites as a light-weight building material to reduce acoustic transmitions.

A novel technique for distal fingertip replantation: Polypropylene suture guided interpositional vein graft.

Science.gov (United States)

Dadaci, Mehmet; Ince, Bilsev; Altuntas, Zeynep; Bitik, Ozan; Uzun, Hakan; Bilgen, Fatma

2015-05-04

Despite current advances in microsurgery, fingertip replantation is still controversial, mainly due to its difficulty and cost. The purpose of this study is to describe a new technique of interposition vein graft guided by polypropylene suture in distal fingertip replantation. A total of eight consecutive Tamai zone 1 fingertip replantations performed by the same author were included. All replantations were performed using interposition vein graft guided by polypropylene suture. This technique involved a vein graft of ∼ 2 cm, with appropriate calibration, obtained from the volar part of the forearm and a 2-0 polyprolene suture passed through the interposition vein graft. Then, a polypropylene suture guide carrying the vein graft was inserted into the artery. The anastomosis was easily performed with the aid of 10-0 or 11-0 nylon in a bloodless medium and without encountering the posterior wall problem. Average surgery time was 2.5 hours (range = 2-3 hours). Among eight Tamai zone 1 replantations, six were successful (75%). There were two replantations lost because of arterial failure. This technique may ease fingertip replantations and increase the success rate for Tamai zone 1 injuries.

Effect of combined extrusion parameters on mechanical properties of basalt fiber-reinforced plastics based on polypropylene

Science.gov (United States)

Bashtannik, P. I.; Ovcharenko, V. G.; Boot, Yu. A.

1997-11-01

Basalt fibers are efficient reinforcing fillers for polypropylene because they increase both the mechanical and the tribotechnical properties of composites. Basalt fibers can compete with traditional fillers (glass and asbestos fibers) of polypropylene with respect to technological, economic, and toxic properties. The effect of technological parameters of producing polypropylene-based basalt fiber-reinforced plastics (BFRPs) by combined extrusion on their mechanical properties has been investigated. The extrusion temperature was found to be the main parameter determining the mechanical properties of the BFRPs. With temperature growth from 180 to 240°C, the residual length of the basalt fibers in the composite, as well as the adhesive strength of the polymer-fiber system, increased, while the composite defectiveness decreased. The tensile strength and elastic modulus increased from 35 to 42 MPa and 3.2 to 4.2 GPa, respectively. At the same time, the growth in composite solidity led to its higher brittleness. Thus, a higher temperature of extrusion allows us to produce materials which can be subjected to tensile and bending loads, while the materials produced at a lower temperature of extrusion are impact stable. The effect of the gap size between the extruder body and moving disks on the mechanical properties of the BFRPs is less significant than that of temperature. An increase of the gap size from 2 to 8 mm improves the impregnation quality of the fibers, but the extruder productivity diminishes. The possibility of controling the properties of reinforced polypropylene by varying the technological parameters of combined extrusion is shown. The polypropylene-based BFRPs produced by the proposed method surpass the properties of glass and asbestos fiber-reinforced plastics.

Design and synthesis of structurally well-defined functional polypropylenes via transition metal-mediated olefin polymerization chemistry

Institute of Scientific and Technical Information of China (English)

Dong Jinyong

2006-01-01

Functionalization of polyolefins is an industrially important yet scientifically challenging research subject.This paper summarizes our recent effort to access structurally well-defined functional polypropylenes via transition metal-mediated olefin polymerization.In one approach,polypropylenes containing side chain functional groups of controlled concentrations were obtained by Ziegler-Natta-catalyzed copolymerization of propylene in combination with either living anionic or controlled radical polymerization of polar monomers.The copolymerization of propylene with 1,4-divinylbenzene using an isospecific MgC12-supported TIC14 catalyst yielded potypropylenes containing pendant styrene moieties.Both metalation reaction with n-butyllithium and hydrochlorination reaction with dry hydrogen chloride selectively and quantitatively occurred at the pendant reactive sites,generating polymeric benzyllithium and 1-chloroethylbenzene species.These species initiated living anionic polymerization of styrene(S)and atom transfer radical polymerization(in the presence of CuC1 and pentamethyldiethylenetriamine) of methyl methacrylate(MMA),respectively,resulting in functional polypropylene graft copolymers(PP-g-PS and PP-g-PMMA)with controllable graft lengths.In another approach,chain end-functionalized polypropylenes containing a terminal OH-group with controlled molecular weights were directly prepared by propylene polymerization with a metaUocene catalyst through a selective aluminum chain transfer reaction.Both approaches proved to be desirable polyolefin functionalization routes in terms of efficiency and polymer structure controllability.

Free radicals in irradiated unstabilized polypropylene, as seen by diffuse reflection absorption-spectrophotometry

International Nuclear Information System (INIS)

Zagorski, Z.P.; Rafalski, A.

1998-01-01

The introduction of UV-Vis absorption spectrophotometry to the study of radiation chemistry of polymers has opened the possibility to investigate even very opaque samples. The virgin powder polypropylene, as obtained from the industrial production line, shows after irradiation unstable products of radiolysis. Until now they were investigated mainly by EPR method. Optical absorption spectra (by diffuse reflection spectrophotometry) contribute to better identification and study of changes in time, temperature and diffusion of reactive gases. Studying the formation of stable compounds, which do not produce EPR signal, we are able to examine these species on the basis of their electronic spectra. The most important results concern the peroxides in irradiated polypropylene

The Effect of Tool Pin Shape of Friction Stir Welding (FSW) on Polypropylene

Science.gov (United States)

Nik, Z. C.; Ishak, M.; Othman, N. H.

2017-09-01

This experiment deals with similar joining of polypropylene (PP) with thickness of 3 mm was carried out by using friction stir welding (FSW) technique. The process parameters, rotational speed, welding speed and tilt angle were fixed of experiments. The tool geometry shapes were the main parameters which were taken into consideration. The optimum designs of tool geometry shape were determined with reference to tensile strength of the joint. During the tensile testing experiment, the results show that all fractured occurs in the heat-affected zone (HAZ) on the polypropylene (PP). Results show that the optimum design can be obtained with same rotational speed, welding speed and tilt angle.

A kinetic study of reactions of coal with polypropylene and polystyrene

Czech Academy of Sciences Publication Activity Database

Straka, Pavel; Náhunková, Jana; Brožová, Zuzana; Zubková, H.

12(126) (2002), s. 81-84 ISSN 1211-1929 R&D Projects: GA AV ČR IAA2046902 Institutional research plan: CEZ:AV0Z3046908 Keywords : coal * kinetics * polypropylene Subject RIV: DH - Mining, incl. Coal Mining

PEG-template for surface modification of zeolite: A convenient material to the design of polypropylene based composite for packaging films

Directory of Open Access Journals (Sweden)

S. Toommee

2018-06-01

Full Text Available Zeolite was successfully modified by conventional synthetic route. Polyethylene glycol was employed for surface modification of zeolite. The surface of zeolite exhibited therefore hydrophobic properties. Less than 5 wt% of modified zeolites with uniform size and shape were integrated into polypropylene matrix. Mechanical properties of composite exhibited the similar trend compare to neat polypropylene. Oxygen transmission rate and water vapor transmission rate were evaluated and it exhibited the strong potential to be a good candidate material in active packaging. Keywords: Zeolite, Composite, Polypropylene, Packaging, PEG-template

Effect of Polypropylene Fibers on Self-Healing and Dynamic Modulus of Elasticity Recovery of Fiber Reinforced Concrete

Directory of Open Access Journals (Sweden)

Adham El-Newihy

2018-02-01

Full Text Available This study aims to evaluate self-healing properties and recovered dynamic moduli of engineered polypropylene fiber reinforced concrete using non-destructive resonant frequency testing. Two types of polypropylene fibers (0.3% micro and 0.6% macro and two curing conditions have been investigated: Water curing (at ~25 Celsius and air curing. The Impact Resonance Method (IRM has been conducted in both transverse and longitudinal modes on concrete cylinders prior/post crack induction and post healing of cracks. Specimens were pre-cracked at 14 days, obtaining values of crack width in the range of 0.10–0.50 mm. Addition of polypropylene fibers improved the dynamic response of concrete post-cracking by maintaining a fraction of the original resonant frequency and elastic properties. Macro fibers showed better improvement in crack bridging while micro fiber showed a significant recovery of the elastic properties. The results also indicated that air-cured Polypropylene Fiber Reinforced Concrete (PFRC cylinders produced ~300 Hz lower resonant frequencies when compared to water-cured cylinders. The analyses showed that those specimens with micro fibers exhibited a higher recovery of dynamic elastic moduli.

Effect of tool geometry on friction stir spot welding of polypropylene sheets

Directory of Open Access Journals (Sweden)

M. K. Bilici

2012-10-01

Full Text Available The effects of tool geometry and properties on friction stir spot welding properties of polypropylene sheets were studied. Four different tool pin geometries, with varying pin angles, pin lengths, shoulder diameters and shoulder angles were used for friction stir spot welding. All the welding operations were done at the room temperature. Lap-shear tensile tests were carried out to find the weld static strength. Weld cross section appearance observations were also done. From the experiments the effect of tool geometry on friction stir spot weld formation and weld strength were determined. The optimum tool geometry for 4 mm thick polypropylene sheets were determined. The tapered cylindrical pin gave the biggest and the straight cylindrical pin gave the lowest lap-shear fracture load.

Compressive and flexural strength of concrete containing palm oil biomass clinker and polypropylene fibres

Science.gov (United States)

Ibrahim, M. H. Wan; Mangi, Sajjad Ali; Burhanudin, M. K.; Ridzuan, M. B.; Jamaluddin, N.; Shahidan, S.; Wong, YH; Faisal, SK; Fadzil, M. A.; Ramadhansyah, P. J.; Ayop, S. S.; Othman, N. H.

2017-11-01

This paper presents the effects of using palm oil biomass (POB) clinker with polypropylene (PP) fibres in concrete on its compressive and flexural strength performances. Due to infrastructural development works, the use of concrete in the construction industry has been increased. Simultaneously, it raises the demand natural sand, which causes depletion of natural resources. While considering the environmental and economic benefits, the utilization of industrial waste by-products in concrete will be the alternative solution of the problem. Among the waste products, one of such waste by-product is the palm oil biomass clinker, which is a waste product from burning processes of palm oil fibres. Therefore, it is important to utilize palm oil biomass clinker as partial replacement of fine aggregates in concrete. Considering the facts, an experimental study was conducted to find out the potential usage of palm oil fibres in concrete. In this study, total 48 number of specimens were cast to evaluate the compressive and flexural strength performances. Polypropylene fibre was added in concrete at the rate of 0.2%, 0.4% and 0.6%, and sand was replaced at a constant rate of 10% with palm oil biomass clinker. The flexural strength of concrete was noticed in the range of 2.25 MPa and 2.29 MPa, whereas, the higher value of flexural strength was recorded with 0.4% polypropylene fibre addition. Hence, these results show that the strength performances of concrete containing POB clinker could be improved with the addition of polypropylene fibre.

Gamma-Irradiation modified polypropylene and nano silver hybrid films: antibacterial activity

International Nuclear Information System (INIS)

Oliani, Washigton L.; Alcantara, Mara T.S.; Lima, Luis F.C.P. de; Bueno, Nelson R.; Rogero, Sizue O.; Lugao, Ademar B.; Parra, Duclerc F.; Huenuman, Nilton E.L.; Santos, Priscila M. dos

2013-01-01

This paper presents a study of films based on blends of polypropylene (PP) with radiation modified PP and insertion of silver nanoparticles aiming bactericide effect. The use of silver (Ag) gives important antibacterial properties since silver is highly toxic for bacteria. The blend of 50/50 PP and gamma irradiated PP was processed in a twin screw extruder. The polypropylene was processed for five PP-Nanocomposite AgNPs in different concentrations of 0.25%; 0.5%; 1.0%; 2.0% and 4.0% in wt%. The material was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), cytotoxicity assay and reduction colony-forming unit (CFU). The analyzed films showed agglomeration of silver particles and regions with homogeneous distribution of the particles. The interactions of the nano silver bactericidal effect with E. coli and S. aureus were assessed. (author)

Gamma-Irradiation modified polypropylene and nano silver hybrid films: antibacterial activity

Energy Technology Data Exchange (ETDEWEB)

Oliani, Washigton L.; Alcantara, Mara T.S.; Lima, Luis F.C.P. de; Bueno, Nelson R.; Rogero, Sizue O.; Lugao, Ademar B.; Parra, Duclerc F., E-mail: washoliani@usp.br [Instituto de Pesquisas Energeticas Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil); Huenuman, Nilton E.L.; Santos, Priscila M. dos [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Dept. of Microbiologia; Riella, Humberto G. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil)

2013-07-01

This paper presents a study of films based on blends of polypropylene (PP) with radiation modified PP and insertion of silver nanoparticles aiming bactericide effect. The use of silver (Ag) gives important antibacterial properties since silver is highly toxic for bacteria. The blend of 50/50 PP and gamma irradiated PP was processed in a twin screw extruder. The polypropylene was processed for five PP-Nanocomposite AgNPs in different concentrations of 0.25%; 0.5%; 1.0%; 2.0% and 4.0% in wt%. The material was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), cytotoxicity assay and reduction colony-forming unit (CFU). The analyzed films showed agglomeration of silver particles and regions with homogeneous distribution of the particles. The interactions of the nano silver bactericidal effect with E. coli and S. aureus were assessed. (author)

Time-Dependent Response of Polypropylene/Clay Nanocomposites Under Tension and Retraction

DEFF Research Database (Denmark)

Drozdov, Aleksey; Christiansen, Jesper de Claville

2013-01-01

Observations are reported in relaxation tests under tension and retraction on polypropylene/clay nanocomposites with various contents of filler. A two-phase constitutive model is developed in cyclic viscoelasticity and viscoplasticity of nanocomposites. Adjustable parameters in the stress–strain ...

EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA); Scientific Opinion on the substantiation of health claims related to isoleucine-proline-proline (IPP) and valine-proline-proline (VPP) and maintenance of normal blood pressure (ID 661, 1831, 1832, 2891, further assessment) pursuant

DEFF Research Database (Denmark)

Tetens, Inge

Following a request from the European Commission, pursuant to Article 13.1 of Regulation (EC) No 1924/2006, the Panel on Dietetic Products, Nutrition and Allergies was asked to provide a scientific opinion on a health claim related to isoleucine-proline-proline (IPP) and valine-proline-proline (VPP....... The proposed target population is the general population. In weighing the evidence, the Panel took into account that 15 of the human intervention studies provided, of which seven were adequately powered to detect small between-group differences in systolic blood pressure, did not observe an effect of IPP...... and VPP on systolic blood pressure or diastolic blood pressure; that interpretation of the results from nine out of the ten studies which reported an effect of IPP and VPP on office systolic blood pressure was limited by methodological weaknesses; that the animal and in vitro/ex vivo studies did...

Application of Interval Type-2 Fuzzy Logic to polypropylene business policy in a petrochemical plant in India

Directory of Open Access Journals (Sweden)

Dipak Kumar Jana

2018-01-01

Full Text Available This paper presents a new approach to predict the quality of polypropylene in petrochemical plants. The proposed approach constructs four different models, based on a large number of data collected from a renowned petrochemical plant in India and uses it to predict the polypropylene quality. The quality of polypropylene depends on the indices such as melt flow index and the xylene solubility of the product and the parameters controlling these two indices are hydrogen flow, donor flow, pressure and temperature of polymerization reactors. Mamdani Interval Type-2 Fuzzy Logic inference systems are formed for first time. The model outcomes are compared with the collected plant data and a sequence of sensitivity analysis elects the most suitable model from them. Some sensitivity analyses are provided using Fuzzy C-Means Clustering to the models.

Effect of particles size on mechanical properties of polypropylene particulate composites

Czech Academy of Sciences Publication Activity Database

Nezbedová, E.; Krčma, F.; Majer, Z.; Hutař, Pavel

2016-01-01

Roč. 7, č. 5 (2016), s. 690-699 ISSN 1757-9864 Institutional support: RVO:68081723 Keywords : Morphology * Mechanical properties * Numerical simulation * Polypropylene particulate composite s * Plasma surface treatment Subject RIV: JI - Composite Material s www.emeraldinsight.com/1757-9864.htm

Trapping of polycyclic aromatic hydrocarbons by amphiphilic cyclodextrin functionalized polypropylene nonwovens

DEFF Research Database (Denmark)

Lumholdt, Ludmilla; Nielsen, Ronnie Bo Højstrup; Larsen, Kim Lambertsen

of the textile fibers. In this study we present the ability of amphiphilic CD coated polypropylene nonwovens to trap 8 different polycyclic aromatic hydrocarbons/endocrine disruptors from aqueous solutions thus demonstrating the potential of using the amphiphilic cyclodextrins for water purification....

Dynamic Mechanical and Thermal Properties of Bagasse/Glass Fiber/Polypropylene Hybrid Composites

Directory of Open Access Journals (Sweden)

Mehdi Roohani

2016-06-01

Full Text Available This work aims to evaluate the thermal and dynamic mechanical properties of bagasse/glass fiber/polypropylene hybrid composites. Composites were prepared by the melt compounding method and their properties were characterized by differential scanning calorimetry (DSC and dynamic mechanical analysis (DMA. DSC results found that with incorporation of bagasse and glass fiber the melting temperature (Tm and the crystallisation temperature (Tc shift to higher temperatures and the degree of crystallinity (Xc increase. These findings suggest that the fibers played the role of a nucleating agent in composites. Dynamic mechanical analysis indicated that by the incorporation of bagasse and glass fiber into polypropylene, the storage modulus ( and the loss modulus ( increase whereas the mechanical loss factor (tanδ decrease. To assess the effect of reinforcement with increasing temperature, the effectiveness coefficient C was calculated at different temperature ranges and revealed that, at the elevated temperatures, improvement of mechanical properties due to the presence of fibers was more noticeable. The fiber-matrix adhesion efficiency determined by calculating of adhesion factor A in terms of the relative damping of the composite (tan δc and the polymer (tan δpand volume fraction of the fibers (Фf. Calculated adhesion factor A values indicated that by adding glass fiber to bagasse/polypropylene system, the fiber-matrix adhesion improve. Hybrid composite containing 25% bagasse and 15% glass fiber showed better fiber-matrix adhesion.

Hierarchical structures and phase nucleation and growth during pressure-induced crystallization of polypropylene containing dispersion of nanoclay: The impact on physical and mechanical properties

International Nuclear Information System (INIS)

Misra, R.D.K.; Yuan, Q.; Chen, J.; Yang, Y.

2010-01-01

The objective of this study is to describe the evolution of structure and phases during pressure-induced crystallization of polymers containing dispersion of nanoparticles, in the pressure range of 0.1-200 MPa. The model material for nanoparticles is nanoclay and the model polymer is polypropylene, which can potentially form several crystalline phases. While the phase selection in polypropylene is dictated by pressure and temperature, however, the introduction of nanoparticles alters the nucleation and growth of phases via nanoparticle interface driven evolution. To delineate and separate the effects of applied crystallization pressure from nanoparticle effects, a relative comparison is made between neat polypropylene and polypropylene containing dispersion of nanoclay under similar experimental conditions. The significant finding is that nanoclay interacts with the host polypropylene in a manner such that it alters the structural morphology of α- and γ-crystals of polypropylene. Furthermore, nanoclay promotes the formation of γ-phase at ambient pressure suggesting its role as structure and morphology director in the stabilization of the less accessible γ-phase, and with the possibility of epitaxial growth that enhances toughness. The equilibrium melting point measurements point to thermodynamic interaction between nanoclay and polypropylene, which is supported by the change in glass transition temperature. Thus, the two components, nanoclay and pressure, together provide a unique opportunity to tune hierarchical structures and phase evolution, which has significant implication on physico-chemical and mechanical properties.

The prediction of mechanical performance of isotactic polypropylene on the basis of processing conditions

NARCIS (Netherlands)

Caelers, H.J.M.; Govaert, L.E.; Peters, G.W.M.

2016-01-01

A strategy is presented to predict the yield kinetics following from different thermomechanical histories experienced during processing in non-isothermal quiescent conditions. This strategy deals with three main parts, i.e. processing, structure and properties. In the first part the applied cooling

Orientation of HDPE inclusions within solid-state drawn rubber-modified isotactic polypropylene: DSC insight

Czech Academy of Sciences Publication Activity Database

Sližová, M.; Raab, Miroslav

2013-01-01

Roč. 130, č. 1 (2013), s. 603-609 ISSN 0021-8995 Institutional support: RVO:61389013 Keywords : blends * differential scanning calorimetry * structure-property relations Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.640, year: 2013

Impact of UV radiation on the physical properties of polypropylene ...

African Journals Online (AJOL)

The purpose of this study was to analyse the influence of simulated sun light radiation (xenon lamp) on physical properties of polypropylene (PP) nonwoven material, which is used for the production of agrotextiles. The research showed that the properties of row cover change when radiated with UV light. Tensile, tearing ...

Physicochemical Study of Irradiated polypropylene/Organo :Modified Montmorillonite Composites by Using Electron Beam Irradiation Technique

International Nuclear Information System (INIS)

Hassan, M.S.

2008-01-01

Polypropylene/ Organo modified montmorillonite composites (PP/ OMMT) were prepared by melt blending with a twin screw extruder. The thermal properties by thermo gravimetric analysis (TGA), the dispersion of OMMT of macromolecules by X-ray diffraction (XRD), mechanical properties and the morphology by scanning electron microscopy (SEM) were investigated. The effect of electron beam irradiation on these properties was also studied. The results showed an intercalation between the silicate layers and the PP polymer matrix. The (PP/ OMMT) composites exhibit higher thermal stability and lower mechanical properties than pure polypropylene

Thermal, mechanical and morphological properties of poly (hydroxybutyrate and polypropylene blends after processing

Directory of Open Access Journals (Sweden)

Wagner Mauricio Pachekoski

2009-06-01

Full Text Available The ever increasing accumulation of plastic waste in the environment has motivated research on polymers that degrade rapidly after being discarded as possible substitutes for conventional inert plastics. Biodegradable polymers can be an alternative, since they have non-toxic residual products and low environmental permanence. Poly (hydroxybutyrate is a biodegradable polymer with a strong potential for industrial purposes, but its thermal instability and fragility limit its applications. Thus, an alternative to improve the processability and properties of poly (hydroxybutyrate is to mix it with another polymer, not necessarily a biodegradable one. In this work, different mixtures of poly(hydroxybutyrate or PHB and polypropylene or PP were extruded and injected. After processing, the blends were studied and their miscibility, mechanical properties and degradability in different soils were analyzed. The main results indicated that the PHB/PP blends had better mechanical properties than pure PHB, as well as improved immiscibility and higher degradation in alkaline soil. The poly-hydroxybutyrate/polypropylene blends showed a tendency for lower crystallinity and stiffness of the polymer matrix, proportional to the amount of polypropylene in the blends, rendering them less stiff and fragile. The degradation tests showed that both pure PHB and blends with 90% PHB and 10% PP were degraded, with loss of their mechanical properties and weight.

Surface modification and micromechanical properties of jute fiber mat reinforced polypropylene composites

Directory of Open Access Journals (Sweden)

2007-05-01

Full Text Available A new treating method using sodium hydroxide (NaOH and Maleic anhydride-grafted polypropylene (MPP emulsion was introduced to treat jute fiber mat in order to enhance the performance of jute/polypropylene (PP composite prepared by film stacking method. The surface modifications of jute fiber mat have been found to be very effective in improving the fiber-matrix adhesion. It was shown that treatments changed not only the surface topography but also the distribution of diameter and strength for the jute fibers, which was analyzed by using a two-parameter Weibull distribution model. Consequently, the interfacial shear strength, flexural and tensile strength of the composites all increased, but the impact strength decreased slightly. These results have demonstrated a new approach to use natural materials to enhance the mechanical performances of composites.

Evaluation of the thermal properties of polypropylene reinforced with palm fibers composites

International Nuclear Information System (INIS)

Capri, M.R.; Santana, L.C.; Mulinari, D.R.

2016-01-01

The aim of this study was to characterize polypropylene reinforced with palm composites. Of this form, it was studied physical and chemical modifications of the in nature fibers, washed with hot water and mercerized. The composites of polypropylene reinforced with 5%, 10% and 20% (wt /wt) in nature fibers and mercerized were evaluated thermally. The fibers were characterized by SEM XRD and TGA / DSC techniques. Results revealed that the mercerized fibers presented higher crystallinity when compared to others, as well as increased roughness, facilitating interlacing with the reinforcement matrix. Thermal studies of the fibers showed that the mercerization caused displacement curves paragraph higher temperatures. The composites reinforced with treated fibers presented largest temperatures and enthalpies of degradation. The content of fiber influenced in enthalpy degradation and reduction in fusion temperature. (author)

Montmorillonite clay/polypropylene (HMSPP) nanocomposites: evaluation of thermal and mechanical properties

International Nuclear Information System (INIS)

Komatsu, L.G.H.; Oliani, W.L.; Lugao, A.B.; Parra, D.F.

2014-01-01

The evaluation of HMSPP (high melt strength polypropylene) properties in nanocomposites was done in composites of 0.1; 1; 3; 5; 10 wt% of Cloisite 20A clay. The PP-g-MA (polypropylene graft maleic anhydride) was the compatibilizer agent in the process of extrusion in twin-screw. Mechanical tests performed in the nanocomposites with higher clay content showed higher values of rupture in 5 and 10 wt% of Cloisite. The thermal properties were evaluate utilizing Calorimetry Differential Exploratory (DSC) and in the sample of 10 wt% of Cloisite were observed increase of the melting temperature and increase of crystallinity. The morphology was investigated by the Scanning Electron Microscopy (SEM) and Fourier Transformed Infrared (FTIR), in which the sample with lower clay amount, 1 wt% of Cloisite showed better dispersion of the clay. X-Ray Diffraction reported the clay intercalation in the sample with 5 wt% of clay. (author)

The main directions in technology investigation of soid oxide fuel cell in Russian Federal Research Center Institute of Physics & Power Engineering (IPPE)

Energy Technology Data Exchange (ETDEWEB)

Ievleva, J.I.; Kolesnikov, V.P.; Mezhertisky, G.S. [and others

1996-04-01

The main direction of science investigations for creation of efficient solid oxide fuel cells (SOFC) in IPPE are considered in this work. The development program of planar SOFC with thin-film electrolyte is shown. General design schemes of experimental SOFC units are presented. The flow design schemes of processes for initial materials and electrodes fabrication are shown. The results of investigations for creation thin-film solid oxide electrolyte at porous cathode by magnetron sputtering from complex metal target in oxidative environment are presented.

Effect of the interfacial adhesion on the tensile and impact properties of carbon fiber reinforced polypropylene matrices

Directory of Open Access Journals (Sweden)

Clara Leal Nogueira

2005-03-01

Full Text Available Thermoplastic composites have been applied in a wide variety of industrial products, showing recently a great potential to be used in aeronautical field. The objectives of this work were to evaluate the fiber/matrix interface of carbon fiber reinforced polypropylene-based matrices after tensile and impact tests and also to compare the mechanical test results of the manufactured laminates. The laminates were prepared by stacking carbon fiber fabric style Plain Weave (CF and films of four different polypropylene matrices, described as (a polypropylene-PP, (b polypropylene-polyethylene copolymer-PP-PE, (c PP-PE with an interfacial compatibilizer-AM1 and (d PP-PE containing an elastomeric modifier-AM2. The composites were processed using hot compression molding. The mechanical testing results showed that the CF-AM1 laminate family presented the lowest impact strength and the highest tensile strength values when compared to the other laminates. SEM analysis observations of both tensile and impact fractured specimens of the CF-PP/PE-AM1 specimens revealed a stronger fiber/matrix interface. The CF-PP/PE-AM2 laminate showed a lower tensile strength and higher impact strength values when compared to the CF-PP/PE-AM1 one. PP-PE and PP laminates presented the lowest impact strength values.

Study of Tensile Properties and Deflection Temperature of Polypropylene/Subang Pineapple Leaf Fiber Composites

Science.gov (United States)

Hafizhah, R.; Juwono, A. L.; Roseno, S.

2017-05-01

The development of eco-friendly composites has been increasing in the past four decades because the requirement of eco-friendly materials has been increasing. Indonesia has a lot of natural fiber resources and, pineapple leaf fiber is one of those fibers. This study aimed to determine the influence of weight fraction of pineapple leaf fibers, that were grown at Subang, to the tensile properties and the deflection temperature of polypropylene/Subang pineapple leaf fiber composites. Pineapple leaf fibers were pretreated by alkalization, while polypropylene pellets, as the matrix, were extruded into sheets. Hot press method was used to fabricate the composites. The results of the tensile test and Heat Deflection Temperature (HDT) test showed that the composites that contained of 30 wt.% pineapple leaf fiber was the best composite. The values of tensile strength, modulus of elasticity and deflection temperature were (64.04 ± 3.91) MPa; (3.98 ± 0.55) GPa and (156.05 ± 1.77) °C respectively, in which increased 187.36%, 198.60%, 264.72% respectively from the pristine polypropylene. The results of the observation on the fracture surfaces showed that the failure modes were fiber breakage and matrix failure.

Morphology and properties of recycled polypropylene/bamboo fibers composites

International Nuclear Information System (INIS)

Phuong, Nguyen Tri; Guinault, Alain; Sollogoub, Cyrille; Chuong, Bui

2011-01-01

Polypropylene (PP) is among the most widely used thermoplastics in many industrial fields. However, like other recycled polymers, its properties usually decrease after recycling process and sometimes are degraded to poor properties level for direct re-employment. The recycled products, in general, need to be reinforced to have competitive properties. Short bamboo fibers (BF) have been added in a recycled PP (RPP) with and without compatibilizer type maleic anhydride polypropylene (MAPP). Several properties of composite materials, such as helium gas permeability and mechanical properties before and after ageing in water, were examined. The effects of bamboo fiber content and fiber chemical treatment have been also investigated. We showed that the helium permeability increases if fiber content is higher than 30% because of a poor adhesion between untreated bamboo fiber and polymer matrix. The composites reinforced by acetylated bamboo fibers show better helium permeability due to grafting of acetyl groups onto cellulose fibers surface and thus improves compatibility between bamboo fibers and matrix, which has been shown by microscopic observations. Besides, mechanical properties of composite decrease with ageing in water but the effect is less pronounced with low bamboo fiber content.

Investigation of Fibres Migration in Cotton/Polypropylene Blended Yarn

Directory of Open Access Journals (Sweden)

Dzmitry RYKLIN

2014-09-01

Full Text Available This study is devoted to theoretical and experimental research of fibres migration in blended yarns. A hypothesis states that due to fibres migration their tension in yarn becomes equal. On the basis of that hypothesis, we identified the factors that affect the migration. The main factors influencing are differences in Young's modulus and density of fibres. Simulating the fibres migration we obtained the formulae for determining the proportion of fibres in the external and inner layers of blended yarn. These formulae were proved by analysis of cross-section of cotton/polypropylene yarn. Results of blended yarn processing in knitting showed that migration of polypropylene fibres in direction to the yarn surface leads to significant increase of yarn breakages due to growth of its friction coefficient. Reduction of the input yarn tension by 10 % – 15 % helped to stabilize the process of knitting. It was found that the usage of theoretical information about fibres migration allows to draw conclusions about the necessity of adjustments to settings of subsequent processing of blended yarns. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.4610

Antifriction basalt-plastics based on polypropylene

Science.gov (United States)

Bashtannik, P. I.; Ovcharenko, V. G.

1997-05-01

A study is made of the dependence of the mechanical and friction-engineering properties of polypropylene reinforced with basalt fibers on the viscosity of the polymer matrix. It is established that the main factors that determine the mechanical properties of the plastics are the quality of impregnation of the fibers by the binder and the residual length of the reinforcing filler in the composite after extrusion and injection molding. The material that was developed has a low friction coefficient and low rate of wear within a relatively brood range of friction conditions. The basalt-plastics can be used in the rubbing parts of machines and mechanisms subjected to dry friction.

High Efficiency Particulate Air (HEPA) filters from polyester and polypropylene fibre nonwovens

CSIR Research Space (South Africa)

Boguslavsky, L

2010-10-01

Full Text Available filtration efficiency. Glass fibres are more harmful to human, compared to polypropylene and polyester fibre which are chemically inert. Hydroentanglement and chemical bonding techniques were utilised in manufacturing nonwovens for dry filtration. Acrylic...

Relations between morphology and micromechanical properties of alpha, beta and gamma phases of iPP

Czech Academy of Sciences Publication Activity Database

Šlouf, Miroslav; Pavlova, Ewa; Krejčíková, Sabina; Ostafinska, Aleksandra; Zhigunov, Alexander; Krzyžánek, Vladislav; Sowinski, P.; Piorkowska, E.

2018-01-01

Roč. 67, May (2018), s. 522-532 ISSN 0142-9418 R&D Projects: GA MZd(CZ) NV15-31269A; GA TA ČR(CZ) TE01020118; GA MŠk(CZ) LO1507 Grant - others:AV ČR(CZ) PAN-17-18 Program:Bilaterální spolupráce Institutional support: RVO:61389013 ; RVO:68081731 Keywords : polypropylene * gamma-phase * micromechanical properties Subject RIV: CD - Macromolecular Chemistry; JA - Electronics ; Optoelectronics, Electrical Engineering (UPT-D) OBOR OECD: Polymer science; Electrical and electronic engineering (UPT-D) Impact factor: 2.464, year: 2016

Air-Coupled Piezoelectric Transducers with Active Polypropylene Foam Matching Layers

Directory of Open Access Journals (Sweden)

Tomás E. Gómez Alvarez-Arenas

2013-05-01

Full Text Available This work presents the design, construction and characterization of air-coupled piezoelectric transducers using 1–3 connectivity piezocomposite disks with a stack of matching layers being the outer one an active quarter wavelength layer made of polypropylene foam ferroelectret film. This kind of material has shown a stable piezoelectric response together with a very low acoustic impedance (<0.1 MRayl. These features make them a suitable candidate for the dual use or function proposed here: impedance matching layer and active material for air-coupled transduction. The transducer centre frequency is determined by the l/4 resonance of the polypropylene foam ferroelectret film (0.35 MHz, then, the rest of the transducer components (piezocomposite disk and passive intermediate matching layers are all tuned to this frequency. The transducer has been tested in several working modes including pulse-echo and pitch-catch as well as wide and narrow band excitation. The performance of the proposed novel transducer is compared with that of a conventional air-coupled transducers operating in a similar frequency range.

Switchgrass (Panicum virgatum L.) as a reinforcing fibre in polypropylene composites

NARCIS (Netherlands)

Oever, van den M.J.A.; Elbersen, H.W.; Keijsers, E.R.P.; Gosselink, R.J.A.; Klerk-Engels, de B.

2003-01-01

In this study the switchgrass (Panicum virgatum L.), a biomass crop being developed in North America and Europe, was tested as a stiffening and reinforcing agent in polypropylene (PP) composites with and without maleic anhydride grafted PP (MAPP) as a compatibiliser and to evaluate the effect of

Coir fiber reinforced polypropylene composite panel for automotive interior applications

Science.gov (United States)

Nadir Ayrilmis; Songklod Jarusombuti; Vallayuth Fueangvivat; Piyawade Bauchongkol; Robert H. White

2011-01-01

In this study, physical, mechanical, and flammability properties of coconut fiber reinforced polypropylene (PP) composite panels were evaluated. Four levels of the coir fiber content (40, 50, 60, and 70 % based on the composition by weight) were mixed with the PP powder and a coupling agent, 3 wt % maleic anhydride grafted PP (MAPP) powder. The water resistance and the...

Comparison of efficacy of polypropylene with chromic catgut suture in stitching paediatric facial lacerations

International Nuclear Information System (INIS)

Hussain, A.; Ahmed, R.; Aziz, O.B.A.; Aamir, M.

2016-01-01

Objective: The objective of this study was to compare 5/0 polypropylene suture with 5/0 chromic catgut in small clean pediatric facial laceration repair in terms of cosmetic outcome. Study Design: Randomized controlled trial.Place and Duration of Study: Combined Military Hospital, Rawalpindi from 26th May 2012 to 25th Nov 2012.Patients and Methods: A total of 300 patients of both gender under 12 years of age, with small clean facial lacerations were selected and divided in two equal groups using random number tables. All the patients underwent suturing in minor operating theater of trauma centre CMH Rawalpindi as day care cases, under local anesthesia and aseptic measures. In group 1, polypropylene 5/0 suture was used where as in group 2 chromic catgut 5/0 was used for suturing. Aseptic dressing was applied. All patients were reviewed on 5th day (for stitch removal in polypropylene group) and 3 months post-operatively to establish cosmetic outcome which was determined by scar visual analog score both by parents of the child and consultant surgeon. Results: The mean VAS (visual analog score) as observed by Consultant surgeon was 79.14 and 78.63 for polypropylene and chromic catgut groups respectively. The mean VAS observed by the parents of the child for respective groups was 76.67 and 76.03. The significance value was 0.961 for parental VAS and 0.988 for surgeons VAS depicting insignificant difference in both suture groups.Conclusion: There is no long-term difference in cosmetic outcomes of both the sutures in the repair of facial lacerations in the pediatric population. No difference in complication rate of wound was observed. In addition, the parents of the children in absorbable suture group expressed satisfaction over prevention of psychological trauma of stitch removal. (author)

Effect of modified polypropylene on the interfacial bonding of polymer–aluminum laminated films

International Nuclear Information System (INIS)

Liang, Chang-Sheng; Lv, Zhong-Fei; Bo, Yang; Cui, Jia-Yang; Xu, Shi-Ai

2015-01-01

Highlights: • Aluminium-polymer composite packing material with high T-peel strength was prepared. • Polypropylene was grafted by acrylic acid, glycidyl methacrylate, maleic anhydride. • Grafted polypropylene greatly improved the T-peel strength. • Chemical bonding plays an important role in improving the adhesion strength. - Abstract: The interfacial bonding between functionalized polymers and chromate–phosphate treated aluminum (Al) foil were investigated in this study. Glycidyl methacrylate (GMA), acrylic acid (AA) and maleic anhydride (MAH) were grafted onto polypropylene (PP) to improve its adhesion strength with the treated Al foil. The interfacial peel strength was evaluated by the T-peel test, and the results showed that modification of PP resulted in a significant improvement in the interfacial peel strength from 1 N/15 mm for pure PP to 10–14 N/15 mm for the modified PP. The surface chemistry, topography and surface energy of the modified PP and Al foil after peeling were characterized by time-of-flight secondary ion mass spectrometry (TOF-SIMS), X-ray photoelectron spectroscopy (XPS), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) and contact angle measurement. The treated Al foil could react with the functional groups of PP, resulting in the formation of new carboxylates. The new chemical bonding rather than the mechanical interlocking contributed to the improvement of adhesion strength

Morphologies and mechanical properties of syndiotactic polypropylene (sPP)/polyethylene (PE) blends

NARCIS (Netherlands)

Loos, J.; Bonnet, M.; Petermann, J.

2000-01-01

The tensile properties of blends based on syndiotactic polypropylene (sPP) and high-density polyethylene (HDPE) have been studied. In order to understand the unexpected decrease in ductility, the crystallization behavior of these blends was characterized by transmission electron microscopy and

Study of the rice husk ash utilization as filler polypropylene matrix and ionization radiation effect on this composite

International Nuclear Information System (INIS)

Alfaro, Eduardo de Faria

2010-01-01

In the first step of this work, it was evaluated the possibility of using rice husk ash as a filler in polypropylene (PP) making a comparison with talc which is the most used mineral filler in polymers. This comparison was made by using polypropylene with 20% rice husk ash as well as polypropylene with 20% talc measuring their properties. Despite the properties of the PP with 20% rice husk ash decreased compared with the composite of polypropylene with 20% talc it can be said that the rice husk ash can be used as filler for or other utilization less noble of PP . This way it is being given a destination for this residue that it is disposable in the environment contributing to its preservation, moreover reducing the product cost. This work had also as an aim to study the ionizing radiation effect in the properties of these composites. It was used the coupling agent, maleic anhydride , to verify a best sample homogenization. According to the results it can be said that PP is a semicrystalline polymer, and so it has its morphology modified when exposed to the irradiation process. This fact is due to the scission mechanisms of the polymeric chains which it is in compliance to the literature. (author)

A strategy of precipitated calcium carbonate (CaCO3) fillers for enhancing the mechanical properties of polypropylene polymers

International Nuclear Information System (INIS)

Thenepalli, Thriveni; Ahn, Ji Whan; Ahn, Young Jun; Han, Choon; Ramakrishna, Chilakala

2015-01-01

A wide variety of fillers are currently used in more than twenty types of polymer resins, although four of them alone (polypropylene, polyamides, thermoplastic polyesters, and polyvinyl chloride) account for 90% of the market of mineral fillers in plastics. Polypropylene (PP) and PVC dominate the market for calcium carbonate. PP is a versatile reinforcement material that can meet engineering and structural specifications and is widely used for automotive components, home appliances, and industrial applications. Talc, mica, clay, kaolin, wollastonite, calcium carbonates, feldspar, aluminum hydroxide, glass fibers, and natural fibers are commonly used in fillers. Among these, calcium carbonate (both natural and synthetic) is the mos abundant and affords the possibility of improved surface finishing, control over the manufacture of products, and increased electric resistance and impact resistance. Meeting the global challenge to reduce the weight of vehicles by using plastics is a significant issue. The current the global plastic and automobile industry cannot survive without fillers, additives, and reinforcements. Polypropylene is a major component of the modern plastic industry, and currently is used in dashboards, wheel covers, and some engine parts in automobiles. This article reports that the use of calcium carbonate fillers with polypropylene is the best choice to enhance the mechanical properties of plastic parts used in automobiles

Effect of ionizing radiation on polypropylene composites reinforced with coconut fibers

Energy Technology Data Exchange (ETDEWEB)

Miranda, Leila F.; Pereira, Nilson C.; Faldini, Sonia B.; Masson, Terezinha J.; Silveira, Luiz H., E-mail: lfmiranda@sti.com.b [Universidade Presbiteriana Mackenzie, Sao Paulo, SP (Brazil). Escola de Engenharia. Curso de Engenharia de Materiais; Silva, Leonardo G. de Andrade e, E-mail: lgasilva@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2009-07-01

The use of the polymeric composite materials has been increasing but these materials have environmental problems related to the discard. To reduce the discard deleterious effect, coconuts, sisal, as well as sugar cane pulp natural based fiber have been studied to replace the synthetic ones. These fibers embedded in a polymeric matrix plays a similar role as the synthetic ones, in terms of mechanical and thermal properties. The natural fibers are environmentally friendly, easy to recycle and biodegradable. The aim of this work is the study of ionizing radiation effects on the properties of recycled polypropylene composites, reinforced with 10%, 15% and 20% of the coconut fibers, using as coupling agent a substance based on maleic anhydride (MAPP) graphitized polypropylene. The samples were molded by injection, irradiated and submitted to thermal and mechanical tests. The mechanical properties (hardness, impact strength and tensile strength), temperature of thermal distortion (HDT) and Vicat softening temperature of the non irradiated and irradiated composites were determined. The irradiation doses were of 30, 50 and 100kGy in a gamma cell. Regarding the thermal and mechanical properties of non-irradiated samples, the incorporation of coconut fibers to polypropylene resulted in a decrease of impact strength, tensile strength and Vicat softening temperature as well as in an increase in hardness and HDT. This result indicates that the coconut fibers do not act like a reinforcement agent but as biodegradable filler. In the irradiated samples, it was observed a decrease in the impact strength, tensile strength, HDT, and thermal distortion temperature and an increase in the hardness and tensile strength. The Vicat softening temperature shows no change. (author)

Effect of ionizing radiation on polypropylene composites reinforced with coconut fibers

International Nuclear Information System (INIS)

Miranda, Leila F.; Pereira, Nilson C.; Faldini, Sonia B.; Masson, Terezinha J.; Silveira, Luiz H.

2009-01-01

The use of the polymeric composite materials has been increasing but these materials have environmental problems related to the discard. To reduce the discard deleterious effect, coconuts, sisal, as well as sugar cane pulp natural based fiber have been studied to replace the synthetic ones. These fibers embedded in a polymeric matrix plays a similar role as the synthetic ones, in terms of mechanical and thermal properties. The natural fibers are environmentally friendly, easy to recycle and biodegradable. The aim of this work is the study of ionizing radiation effects on the properties of recycled polypropylene composites, reinforced with 10%, 15% and 20% of the coconut fibers, using as coupling agent a substance based on maleic anhydride (MAPP) graphitized polypropylene. The samples were molded by injection, irradiated and submitted to thermal and mechanical tests. The mechanical properties (hardness, impact strength and tensile strength), temperature of thermal distortion (HDT) and Vicat softening temperature of the non irradiated and irradiated composites were determined. The irradiation doses were of 30, 50 and 100kGy in a gamma cell. Regarding the thermal and mechanical properties of non-irradiated samples, the incorporation of coconut fibers to polypropylene resulted in a decrease of impact strength, tensile strength and Vicat softening temperature as well as in an increase in hardness and HDT. This result indicates that the coconut fibers do not act like a reinforcement agent but as biodegradable filler. In the irradiated samples, it was observed a decrease in the impact strength, tensile strength, HDT, and thermal distortion temperature and an increase in the hardness and tensile strength. The Vicat softening temperature shows no change. (author)

The effect of temperature and drawing ratio on the mechanical properties of polypropylene monofilaments

Science.gov (United States)

Taheri, Hesam; Nóbrega, João Miguel; Samyn, Pieter; Covas, José Antonio

2014-05-01

In this work, the simultaneous effect of both temperature and drawing ratio during processing of polypropylene monofilaments has been investigated. The basis of this work specifically aims at emphasizing the conditions of temperature and drawing ratio applied in the cooling bath, in order to find out under which conditions the named parameters can be applied in a processing line under continuous extrusion. The effects of temperature are studied for a constant total drawing ratio to analyze the influences on mechanical properties and structural differences of the final polypropylene monofilament. The quenched monofilaments were drawn around an adjustable guide assembly in the quench bath and first drawing stage, imparting thermal and mechanical treatments to the filaments. In the heating stage, monofilaments are affected to high-speed draw rolls while passing through the oven. As such, the best conditions to produce a polypropylene monofilament with high tenacity strength were determined. Results of this study show that the monofilament properties are significantly affected by temperature in the cooling zone. The nature of the first drawing had a significant effect on the end properties and monofilaments with modulus of 637 MPa have finally been manufactured. We have also proposed a new hypothesis, which is termed "gap nucleation" and determine this phenomenon in the gap between die and cooling bath.

Bio-composites based on polypropylene reinforced with Almond Shells particles: Mechanical and thermal properties

International Nuclear Information System (INIS)

Essabir, H.; Nekhlaoui, S.; Malha, M.; Bensalah, M.O.; Arrakhiz, F.Z.; Qaiss, A.; Bouhfid, R.

2013-01-01

Highlights: • Almond Shells (ASs) particles have been used as reinforcement in polypropylene matrix. • The SEBS-g-MA has been used to improve the adhesion between matrix and particles. • The mechanical and thermal properties of the composite have been improved by the AS. - Abstract: In this work, Almond Shells (ASs) particles are used as reinforcement in a thermoplastic matrix as polypropylene (PP). Composites containing Almond Shells (ASs) particles with and without compatibilizer (maleic anhydride grafted polypropylene; SEBS-g-MA) for various particle content (5, 10, 15, 20, 25, 30 wt.%) was investigated by means of studying their mechanical, thermal and rheological properties. The composites were prepared in a twin-screw extruder and assessed by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), tensile testing and Dynamic Mechanical Analysis (DMA). Results show a clear improvement in mechanical and rheological properties from the use of Almond Shells particles in the matrix without and with maleic anhydride compatibilizer, corresponding to a gain in Young’s modulus of 56.2% and 35% respectively, at 30 wt.% particle loading. Thermal analysis revealed that incorporation of particle in the composites resulted in increase in the initial thermal decomposition temperatures

Sensitivity of the polypropylene to the strain rate: experiments and modeling

International Nuclear Information System (INIS)

Abdul-Latif, A.; Aboura, Z.; Mosleh, L.

2002-01-01

Full text.The main goal of this work is first to evaluate experimentally the strain rate dependent deformation of the polypropylene under tensile load; and secondly is to propose a model capable to appropriately describe the mechanical behavior of this material and especially its sensitivity to the strain rate. Several experimental tensile tests are performed at different quasi-static strain rates in the range of 10 -5 s -1 to 10 -1 s -1 . In addition to some relaxation tests are also conducted introducing the strain rate jumping state during testing. Within the framework of elastoviscoplasticity, a phenomenological model is developed for describing the non-linear mechanical behavior of the material under uniaxial loading paths. With the small strain assumption, the sensitivity of the polypropylene to the strain rate being of particular interest in this work, is accordingly taken into account. As a matter of fact, since this model is based on internal state variables, we assume thus that the material sensitivity to the strain rate is governed by the kinematic hardening variable notably its modulus and the accumulated viscoplastic strain. As far as the elastic behavior is concerned, it is noticed that such a behavior is slightly influenced by the employed strain rate rage. For this reason, the elastic behavior is classically determined, i.e. without coupling with the strain rate dependent deformation. It is obvious that the inelastic behavior of the used material is thoroughly dictated by the applied strain rate. Hence, the model parameters are well calibrated utilizing several experimental databases for different strain rates (10 -5 s -1 to 10 -1 s -1 ). Actually, among these experimental results, some experiments related to the relaxation phenomenon and strain rate jumping during testing (increasing or decreasing) are also used in order to more perfect the model parameters identification. To validate the calibrated model parameters, simulation tests are achieved

Polypropylene-polyethylene blends modified by gamma radiation

International Nuclear Information System (INIS)

Terence, Mauro C.; Ruiz, Francisco C.

2009-01-01

One way to obtain a better mechanical property of polypropylene and polyethylene is to increasing the number of polymer chains cross-linked by gamma radiation. After irradiation a network is formed as a result of various chemical reactions and the radicals formed are concentrated in the amorphous phase. With the objective to improve the mechanical properties of PP, blends with PE were prepared and irradiated in doses up to 500 kGy, in atmospheric ambient. The molecular characterization of the blends was made by infrared spectroscopy and the data showed an increase in rigidity and a unique behaviour in Izod impact resistance. (author)

Radiation oxidation of polypropylene: A solid-state 13C NMR study using selective isotopic labeling

International Nuclear Information System (INIS)

Mowery, Daniel M.; Assink, Roger A.; Derzon, Dora K.; Klamo, Sara B.; Bernstein, Robert; Clough, Roger L.

2007-01-01

Polypropylene samples, in which the three different carbon atoms along the chain were selectively labeled with carbon-13, were subjected to radiation under inert and air atmospheres, and to post-irradiation exposure in air at various temperatures. By using solid-state 13 C NMR measurements at room temperature, we have been able to identify and quantify the oxidation products. The isotopic labeling provides insight into chemical reaction mechanisms, since oxidation products can be traced back to their positions of origin on the macromolecule. The major products include peroxides and alcohols, both formed at tertiary carbon sites along the chain. Other products include methyl ketones, acids, esters, peresters, and hemiketals formed from reaction at the tertiary carbon, together with in-chain ketones and esters from reaction at the secondary chain carbon. No evidence is found of products arising from reactions at the methyl side chain. Significant temperature-dependent differences are apparent; for example much higher yields of chain-end methyl ketones, which are the indicator product of chain scission, are generated for both elevated temperature irradiation and for post-irradiation treatment at elevated temperatures. Time-dependent plots of yields of the various oxidation products have been obtained under a wide range of conditions, including the post-irradiation oxidation of a sample at room temperature in air that has been monitored for 2 years. Radiation-oxidation products of polypropylene are contrasted to products measured for 13 C-labeled polyethylene in an earlier investigation: the peroxides formed in irradiated polypropylene are remarkably longer lived, the non-peroxidic products are significantly different, and the overall ratios of oxidation products in polypropylene change relatively little as a function of the extent of oxidation

Synthesis and characterization of polypropylene/graphite nano composite preparation for in situ polymerization

International Nuclear Information System (INIS)

Montagna, L.S.; Fim, F. de C.; Galland, G.B.

2010-01-01

This paper presents the synthesis of polypropylene/graphite nanocomposites through in situ polymerization, using the metallocene catalyst C 20 H 16 Cl 2 Zr (dichloro(rac-ethylenebis(indenyl))zircon(IV)). The graphite nanosheets in nano dimensions were added to the polymer matrix in percentages of 0.6;1.0;4.2;4.8 and 6.0% (w/w). The TEM images indicated that the thickness of graphite nanosheets ranged from 4 to 60 nm and by means of XRD analysis it was observed that the physical and chemical treatment did not destroyed the graphite layers. The presence of nanosheets did not decrease the catalytic activity of the nanocomposites. TEM images and XRD analysis of nanocomposites showed a good dispersion of the graphite nanosheets in the polypropylene matrix. (author)

Spinning, drawing and physical properties of polypropylene nanocomposite fibers with fumed nanosilica

Czech Academy of Sciences Publication Activity Database

Dabrowska, I.; Fambri, L.; Pegoretti, A.; Šlouf, Miroslav; Vacková, Taťana; Kolarik, J.

2015-01-01

Roč. 9, č. 3 (2015), s. 277-290 ISSN 1788-618X R&D Projects: GA ČR(CZ) GA14-17921S Institutional support: RVO:61389013 Keywords : polypropylene * fibers * nanocomposites Subject RIV: JI - Composite Materials Impact factor: 2.965, year: 2015

The mechanisms of reinforcement of polypropylene by graphene nanoplatelets

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Siti Rohana; Xue, Chengzhe; Young, Robert J., E-mail: robert.young@manchester.ac.uk

2017-02-15

Highlights: • The thermal stability of the polypropylene is improved significantly with the GNPs. • The melting temperature and degree of crystallinity of the PP are both increased. • The effective Young’s modulus of the GNP reinforcement is 100 GPa. • The same effective Young’s modulus is found from Raman band shifts. - Abstract: A detailed analysis has been undertaken of the mechanisms of reinforcement of polypropylene (PP) by the addition of graphene nanoplatelets (GNP). The PP/GNP nanocomposites were processed by melt mixing followed by injection moulding and microstructure was fully characterized. It was found that the GNPs increased the thermal stability of the PP and aided crystal nucleation. The mechanical properties of the nanocomposites were evaluated using both tensile testing and dynamic mechanical thermal analysis. The addition of GNPs led to a significant increase in the Young’s modulus of the PP, coupled with a decrease in the yield stress and a reduction in the elongation to failure. Stress transfer from the PP matrix to the GNP reinforcement was followed from stress-induced shifts of the 2D Raman band and the effective Young’s modulus of the GNPs in the nanocomposites was found to be about 100 GPa, shown to be consistent with the expected value.

Investigating the influence of alkalization on the mechanical and water absorption properties of coconut and sponge fibers reinforced polypropylene composites

Directory of Open Access Journals (Sweden)

Okikiola Ganiu AGBABIAKA

2014-11-01

Full Text Available Natural fibers are products made from renewable agricultural and forestry feedstock, which can include wood, grasses, and crops, as well as wastes and residues. There are two primary ways these fibers are used: to create polymers or as reinforcement and filler. Thermoplastic polymer may be reinforced or filled using natural fibers such as coir, sponge, hemp, flax, or sisal. This paper focused on the influence of alkalization (NaOH treatment on the mechanical and water absorption properties of selected natural fibers (coconut and sponge fibers reinforced polypropylene composites. In this study, coconut and sponge fiber were extracted from its husk by soaking them in water and was dried before it was cut into 10mm length. Those fibers were chemically treated with sodium hydroxide (NaOH in a shaking water bath before it was used as reinforcement in polypropylene composite. The reinforced polypropylene composite was produced by dispersing the coconut fibers randomly in the polypropylene before it was fabricated in a compression molding machine where the composite was produced. The fiber content used were; 2%wt, 4%wt, 6%wt, 8%wt and 10%wt. Tensile and flexural properties was observed from universal testing machine while water absorption test was carried out on the samples for seven (7 days. It was observed that the influence of NaOH treatment highly enhanced the Flexural and water absorption properties of sponge fiber reinforced polypropylene composites than coconut fiber reinforced composite samples.

Irradiation and processing of oil palm empty fruit bunch fibres - polypropylene composites

International Nuclear Information System (INIS)

Khairul Zaman Mohd Dahlan; Syarifah Hanisah Syed Abdul Aziz

2000-01-01

In this study, polypropylene was blended with oil palm empty fruit bunch fibres at a ratio of 60 to 40 by weight, respectively. Trimethylolpropane triacrylate (TMPTA) was used as the crosslinking agent. Homopolymer Polypropylene of MFI 14.0 and EFB fibres of 0.5 -1.0 mm sizes were used through out the experiment. Processing parameters such as temperature, rotor speed and processing time were optimized. Modes of irradiation were established to determine the optimum properties of the composites. The mechanical properties of the composite such as tensile strength, tensile modulus, flexural strength and flexural modulus were measured. The results indicate that temperature, 185 degree C, with a rotor speed of 40 rpm and 9 minutes processing time are sufficient to produce the optimum mechanical properties of PP/EFB composite. Modes of adding TMPTA into the blend and modes of irradiation also have influenced the properties of the composites

Evaluation of endoscopic laser excision of polypropylene mesh/sutures following anti-incontinence procedures.

LENUS (Irish Health Repository)

Davis, N F

2012-11-01

We reviewed our experience with and outcome of the largest series to our knowledge of patients who underwent endoscopic laser excision of eroded polypropylene mesh or sutures as a complication of previous anti-incontinence procedures.

Nanocomposites of polypropylene/titanate nanotubes: morphology, nucleation effects of nanoparticles and properties

Czech Academy of Sciences Publication Activity Database

Mikešová, Jana; Šlouf, Miroslav; Gohs, U.; Popelková, Daniela; Vacková, Taťana; Vu, Ngoc Húng; Kratochvíl, Jaroslav; Zhigunov, Alexander

2014-01-01

Roč. 71, č. 4 (2014), s. 795-818 ISSN 0170-0839 R&D Projects: GA ČR GAP205/10/0348 Institutional support: RVO:61389013 Keywords : titanate nanotubes * polypropylene nanocomposites * nucleation effect Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.438, year: 2014

Thermal properties of light-weight concrete with waste polypropylene aggregate

Science.gov (United States)

Záleská, Martina; Pokorný, Jaroslav; Pavlíková, Milena; Pavlík, Zbyšek

2017-07-01

Thermal properties of a sustainable light-weight concrete incorporating high volume of waste polypropylene as partial substitution of natural aggregate were studied in the paper. Glass fiber reinforced polypropylene (GFPP), a by-product of PP tubes production, partially substituted fine natural silica aggregate in 10, 20, 30, 40, and 50 mass%. In order to quantify the effect of GFPP use on concrete properties, a reference concrete mix without plastic waste was studied as well. For the applied GFPP, bulk density, matrix density, and particle size distribution were measured. Specific attention was paid to thermal transport and storage properties of GFPP that were examined in dependence on compaction time. For the developed light-weight concrete, thermal properties were accessed using transient impulse technique, whereas the measurement was done in dependence on moisture content, from the dry state to fully water saturated state. Additionally, the investigated thermal properties were plotted as function of porosity. The tested light-weight concrete was found to be prospective construction material possessing improved thermal insulation function. Moreover, the reuse of waste plastics in concrete composition was beneficial both from the environmental and financial point of view considering plastics low biodegradability and safe disposal.

Bio-composites fabricated by sandwiching sisal fibers with polypropylene (PP)

Energy Technology Data Exchange (ETDEWEB)

Sosiati, H., E-mail: hsosiati@gmail.com [Nanomaterials Research Group, LPPT Universitas Gadjah Mada (Indonesia); Nahyudin, A., E-mail: ahmadnahyudin@yahoo.co.id; Fauzi, I., E-mail: ikhsannurfauzi@gmail.com; Wijayanti, D. A., E-mail: wijayantidwiastuti@gmail.com [Department of Physics, Faculty of Mathematics and Natural Sciences, Gadjah Mada University (Indonesia); Triyana, K., E-mail: triyana@ugm.ac.id [Nanomaterials Research Group, LPPT Universitas Gadjah Mada (Indonesia); Department of Physics, Faculty of Mathematics and Natural Sciences, Gadjah Mada University (Indonesia)

2016-04-19

Sisal fibers reinforced polypropylene (PP) composites were successfully fabricated using sandwiching sisal fibers with PP sheets. The ratio of fiber and polymer matrix was 50:50 (wt. %). Untreated short and long sisal fibers, and alkali treated short sisal fibers in 6% NaOH at 100°C for 1 and 3 h were used as reinforcement or fillers. A small amount (3 wt. %) of maleic anhydride grafted polypropylene (MAPP) was added as a coupling agent. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy were used to characterize the surface morphology and chemical composition of the fibers, respectively. Flexural test of sisal/PP composites was done according to ASTM D 790-02. The results showed that flexural strength of untreated long fiber reinforced composite is much higher than that of the untreated and alkali treated short fibers reinforced composites with and without the addition of MAPP. Alkalization related to fiber surface modification, fiber length/fiber orientation and a composite fabrication technique are important factors in contributing to the fiber distribution within the matrix, the bonding between the fiber and the matrix and the enhancement of flexural strength of the bio-composite.

Bio-composites fabricated by sandwiching sisal fibers with polypropylene (PP)

International Nuclear Information System (INIS)

Sosiati, H.; Nahyudin, A.; Fauzi, I.; Wijayanti, D. A.; Triyana, K.

2016-01-01

Sisal fibers reinforced polypropylene (PP) composites were successfully fabricated using sandwiching sisal fibers with PP sheets. The ratio of fiber and polymer matrix was 50:50 (wt. %). Untreated short and long sisal fibers, and alkali treated short sisal fibers in 6% NaOH at 100°C for 1 and 3 h were used as reinforcement or fillers. A small amount (3 wt. %) of maleic anhydride grafted polypropylene (MAPP) was added as a coupling agent. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy were used to characterize the surface morphology and chemical composition of the fibers, respectively. Flexural test of sisal/PP composites was done according to ASTM D 790-02. The results showed that flexural strength of untreated long fiber reinforced composite is much higher than that of the untreated and alkali treated short fibers reinforced composites with and without the addition of MAPP. Alkalization related to fiber surface modification, fiber length/fiber orientation and a composite fabrication technique are important factors in contributing to the fiber distribution within the matrix, the bonding between the fiber and the matrix and the enhancement of flexural strength of the bio-composite.

Bio-composites fabricated by sandwiching sisal fibers with polypropylene (PP)

Science.gov (United States)

Sosiati, H.; Nahyudin, A.; Fauzi, I.; Wijayanti, D. A.; Triyana, K.

2016-04-01

Sisal fibers reinforced polypropylene (PP) composites were successfully fabricated using sandwiching sisal fibers with PP sheets. The ratio of fiber and polymer matrix was 50:50 (wt. %). Untreated short and long sisal fibers, and alkali treated short sisal fibers in 6% NaOH at 100°C for 1 and 3 h were used as reinforcement or fillers. A small amount (3 wt. %) of maleic anhydride grafted polypropylene (MAPP) was added as a coupling agent. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy were used to characterize the surface morphology and chemical composition of the fibers, respectively. Flexural test of sisal/PP composites was done according to ASTM D 790-02. The results showed that flexural strength of untreated long fiber reinforced composite is much higher than that of the untreated and alkali treated short fibers reinforced composites with and without the addition of MAPP. Alkalization related to fiber surface modification, fiber length/fiber orientation and a composite fabrication technique are important factors in contributing to the fiber distribution within the matrix, the bonding between the fiber and the matrix and the enhancement of flexural strength of the bio-composite.

Physico-chemical characterization of functionalized polypropylenic fibers for prosthetic applications

Science.gov (United States)

Nisticò, Roberto; Faga, Maria Giulia; Gautier, Giovanna; Magnacca, Giuliana; D'Angelo, Domenico; Ciancio, Emanuele; Piacenza, Giacomo; Lamberti, Roberta; Martorana, Selanna

2012-08-01

Polypropylene (PP) fibers can be manufactured to form nets which can find application as prosthesis in hernioplasty. One of the most important problem to deal with when nets are applied in vivo consists in the reproduction of bacteria within the net fibers intersections. This occurs right after the application of the prosthesis, and causes infections, thus it is fundamental to remove bacteria in the very early stage of the nets application. This paper deals with the physico-chemical characterization of such nets, pre-treated by atmospheric pressure plasma dielectric barrier discharge apparatus (APP-DBD) and functionalized with an antibiotic drug such as chitosan. The physico-chemical characterization of sterilized nets, before and after the functionalization with chitosan, was carried out by means of scanning electron microscopy (SEM) coupled with EDS spectroscopy, FTIR spectroscopy, drop shape analysis (DSA), X-ray diffraction and thermal analyses (TGA and DSC). The aim of the work is to individuate a good strategy to characterize this kind of materials, to understand the effects of polypropylene pre-treatment on functionalization efficiency, to follow the materials ageing in order to study the effects of the surface treatment for in vivo applications.

Physico-chemical characterization of functionalized polypropylenic fibers for prosthetic applications

International Nuclear Information System (INIS)

Nisticò, Roberto; Faga, Maria Giulia; Gautier, Giovanna; Magnacca, Giuliana; D’Angelo, Domenico; Ciancio, Emanuele; Piacenza, Giacomo; Lamberti, Roberta; Martorana, Selanna

2012-01-01

Polypropylene (PP) fibers can be manufactured to form nets which can find application as prosthesis in hernioplasty. One of the most important problem to deal with when nets are applied in vivo consists in the reproduction of bacteria within the net fibers intersections. This occurs right after the application of the prosthesis, and causes infections, thus it is fundamental to remove bacteria in the very early stage of the nets application. This paper deals with the physico-chemical characterization of such nets, pre-treated by atmospheric pressure plasma dielectric barrier discharge apparatus (APP-DBD) and functionalized with an antibiotic drug such as chitosan. The physico-chemical characterization of sterilized nets, before and after the functionalization with chitosan, was carried out by means of scanning electron microscopy (SEM) coupled with EDS spectroscopy, FTIR spectroscopy, drop shape analysis (DSA), X-ray diffraction and thermal analyses (TGA and DSC). The aim of the work is to individuate a good strategy to characterize this kind of materials, to understand the effects of polypropylene pre-treatment on functionalization efficiency, to follow the materials ageing in order to study the effects of the surface treatment for in vivo applications.

Hierarchically mesoporous silica materials prepared from the uniaxially stretched polypropylene membrane and surfactant templates

International Nuclear Information System (INIS)

Wang Xiaocong; Ma Jin; Liu Jin; Zhou Chen; Zhao, Yan; Yi Shouzhi; Yang Zhenzhong

2006-01-01

Hierarchically mesoporous silica materials with a bimodal distribution were template-prepared from uniaxially stretched polypropylene membrane in the presence of a surfactant via a sol-gel process. Their regularity and morphologies were characterized by transmission electron microscopy (TEM), x-ray diffraction and Brunauer-Emmett-Teller (BET) surface area analysis. The larger channel pores formed by removing the microfibrils of uniaxially stretched polypropylene membrane have a broad pore size distribution, and their size is around 13 nm. In contrast, the smaller mesopores formed by surfactant templates have a narrow distribution; their size is about 3.9 nm. The size of the smaller pores could be tuned from 2 to 6 nm by selecting different surfactants and by changing the concentration of reactants

Sorption of heavy metals on a chitosan-grafted-polypropylene nonwoven geotextile

Directory of Open Access Journals (Sweden)

Vandenbossche M.

2013-04-01

Full Text Available This work describes the development of an environmental friendly functionalized polypropylene nonwoven geotextile (PP in order to trap heavy metals in sediments and sludges. Chitosan was chosen as the sorbent because of its ability to trap heavy metals, of its natural origin (from shells, and of its low cost. PP was first functionalized with acrylic acid using a cold plasma process, in order to bring some reactive carboxylic functions onto the surface. Chitosan was then covalently grafted on the acrylic acid modified polypropylene. The functionalized surfaces were characterized by FTIR (Fourier Transform InfraRed and chitosan was thus proven to be grafted. The ability of the functionalized textile to trap heavy metals was then investigated. Copper was chosen as the model heavy metal, and artificial solutions of CuSO4 were prepared for the experiments. Sorption studies among the concentration of copper in polluted solutions at 20°C were carried out with PP-g-AA-chitosan (Polypropylene-grafted-Acrylic acid-chitosan in order to evaluate the maximum of absorption of this surface: the textile can chelate copper increasingly with the initial copper concentration until 800 ppm where it reaches a plateau at about 30 mg/L. The effects of pH and of the ionic strength (absorption in a NaCl containing solution were finally investigated. The trapping of Cu2+ decreases slowly when the ionic strength increases. For a seawater-like NaCl concentration of 30g/L, the textile still chelates about 20 mg/L of Cu2+. Finally, the optimum pH to trap the maximum amount of copper was determined to be 4.75, which corresponds to the optimum pH for the solubility of the chitosan.

Study of oil sorption behavior of filled and structured fiber assemblies made from polypropylene, kapok and milkweed fibers.

Science.gov (United States)

Rengasamy, R S; Das, Dipayan; Karan, C Praba

2011-02-15

This article reports on oil sorption behavior of fiber assemblies made up of single natural and synthetic fibers as well as blend of natural and synthetic fibers when tested with high density oil and diesel oil. A series of filled fiber assemblies were prepared from 100% polypropylene, kapok, and milkweed fibers and another series of bonded structured fiber assemblies were prepared from a 70/30 blend of kapok and polypropylene fibers and a 70/30 blend of milkweed and polypropylene fibers. It was observed that the porosity of the fiber assemblies played a very important role in determining its oil sorption capacity. The polypropylene fiber assembly exhibited the highest sorption capacity (g/g) followed by the kapok and milkweed fiber assemblies at porosity milkweed fibers have intra fiber porosities of 0.81 and 0.83, respectively. All the fiber assemblies showed higher oil sorption capacity with the high density oil as compared to the diesel oil. As the kapok and milkweed fiber have low cellulose content, hence their slow degradation is an advantage in fresh and marine water applications. The good sorption capacity of kapok and milkweed fiber assemblies along with their bio-degradable nature offer great scope for structuring them into fiber assemblies with large porosity and uniform pores to have efficient oil sorbents. Copyright © 2010 Elsevier B.V. All rights reserved.

Modification of polycarbonate and polypropylene surfaces by argon ion cluster beams

Czech Academy of Sciences Publication Activity Database

Biederman, H.; Slavinská, D.; Boldyreva, H.; Lehmberg, H.; Takaoka, G.; Matsuo, J.; Kinpara, H.; Zemek, Josef

2001-01-01

Roč. 19, č. 6 (2001), s. 2050-2056 ISSN 0734-2101 R&D Projects: GA MŠk ME 177 Institutional research plan: CEZ:AV0Z1010914; CEZ:MSM113200002 Keywords : polycarbonate * polypropylene * surfometer * atomic force microscop * X-ray photoelectron spectroscopy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.448, year: 2001

A strategy of precipitated calcium carbonate (CaCO{sub 3}) fillers for enhancing the mechanical properties of polypropylene polymers

Energy Technology Data Exchange (ETDEWEB)

Thenepalli, Thriveni; Ahn, Ji Whan [Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon (Korea, Republic of); Ahn, Young Jun; Han, Choon [Kwangwoon University, Seoul (Korea, Republic of); Ramakrishna, Chilakala [Hanil Cement, Danyang (Korea, Republic of)

2015-06-15

A wide variety of fillers are currently used in more than twenty types of polymer resins, although four of them alone (polypropylene, polyamides, thermoplastic polyesters, and polyvinyl chloride) account for 90% of the market of mineral fillers in plastics. Polypropylene (PP) and PVC dominate the market for calcium carbonate. PP is a versatile reinforcement material that can meet engineering and structural specifications and is widely used for automotive components, home appliances, and industrial applications. Talc, mica, clay, kaolin, wollastonite, calcium carbonates, feldspar, aluminum hydroxide, glass fibers, and natural fibers are commonly used in fillers. Among these, calcium carbonate (both natural and synthetic) is the mos abundant and affords the possibility of improved surface finishing, control over the manufacture of products, and increased electric resistance and impact resistance. Meeting the global challenge to reduce the weight of vehicles by using plastics is a significant issue. The current the global plastic and automobile industry cannot survive without fillers, additives, and reinforcements. Polypropylene is a major component of the modern plastic industry, and currently is used in dashboards, wheel covers, and some engine parts in automobiles. This article reports that the use of calcium carbonate fillers with polypropylene is the best choice to enhance the mechanical properties of plastic parts used in automobiles.

Modification of bentonite clay and application on polypropylene nano composites

International Nuclear Information System (INIS)

Oliveira, Akidauana D.B.; Rodrigues, Andre W.B.; Agrawal, Pankaj; Araujo, Edcleide M.; Melo, Tomas J.A.

2009-01-01

This work consisted on the modification of Brasgel PA clay with ionic surfactant Praepagen WB and its incorporation into polypropylene. The results of infrared and DR-X was showed that the intercalation of surfactant in the clay and the incorporation of organoclay in PP matrix resulted in the formation of an intercalated structure. The impact strength of PP increased with the incorporation of organoclay. (author)

Development of novel nanocomposite adsorbent based on potassium nickel hexacyanoferrate-loaded polypropylene fabric.

Science.gov (United States)

Bondar, Yuliia; Kuzenko, Svetlana; Han, Do-Hung; Cho, Hyun-Kug

2014-01-01

A nanocomposite adsorbent based on potassium nickel hexacyanoferrate-loaded polypropylene fabric was synthesized for selective removal of Cs ions from contaminated waters by a two-stage synthesis: radiation-induced graft polymerization of acrylic acid monomer onto the nonwoven polypropylene fabric surface with subsequent in situ formation of potassium nickel hexacyanoferrate (KNiHCF) nanoparticles within the grafted chains. Data of scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy confirmed the formation of KNiHCF homogeneous phase on the fabric surface, which consisted of crystalline cubic-shaped nanoparticles (70 to 100 nm). The efficiency of the synthesized adsorbent for removal of cesium ions was evaluated under various experimental conditions. It has demonstrated a rapid adsorption process, high adsorption capacity over a wide pH range, and selectivity in Cs ion removal from model solutions with high concentration of sodium ions.

IPP (INNOVACIÓN EN PRODUCTOS Y PROCESOS PARA EL SECTOR DE LAS MATERIAS PRIMAS MINERALES Y ENERGÉTICAS

Directory of Open Access Journals (Sweden)

CORREA ESPINAL ALEXANDER

2010-05-01

Full Text Available Este articulo proscrita los resultados del proyecto ce Investigación IPP (Innovación ce Procesos y Productos que plantea un análisis profundo y sistémico de las cadenas productivas, basado en el estudio de la productividad y los procesos. Este proyecto se trabajo en 4 fases: Inteligencia, Experimentación. Innovación y Apropiación tecnológica. Estas etapas están dirigidas al mejoramiento continuo ce los procesos, de los productos ce la organización y de las interacciones entre los actores de la cadena productiva de las materias primas minerales y energéticas. En la fase de inteligencia, se estudiaron las características, las ecesidades. el mercado y el entorno de la cadena productiva que son el resultado del aprovechamiento de los recursos naturales y del ambiente En la segunda fase, se caracterizó la formulación, diseño c implantación ce prototipos de procesos y productos que emulen el comportamiento del proceso en un sistema real y sean amigables con el medio ambiente. Teniendo en cuenta las dos primeras fases, la tercera se caracterizó por la formulación y el diseño ce nuevos procesos y productos que mejoren la eficiencia y la productividad. En la última fase del proyecto, se planteó el servicio de apropiación tecnológica que busca transferir innovación y conocimiento de punta a la cadena. Finalmente el resultado ce IPP es la propuesta de un centro de innovación y tecnología en la Universidad Nacional de Colombia, que garantizará la apropiación y adecuación de las soluciones a las cadenas productivas, siendo una innovación para el sector de la minería, los materiales y la energía, y teniendo como principios, productos y procesos amigables con el ambiente.

Recycling of asbestos tailings used as reinforcing fillers in polypropylene based composites.

Science.gov (United States)

Zhai, Wensi; Wang, Yao; Deng, Yuan; Gao, Hongli; Lin, Zhen; Li, Mao

2014-04-15

In this work, asbestos tailings were recycled and used as reinforcing fillers to enhance the mechanical properties of polypropylene (PP). A silane coupling agent was used to chemically modify the asbestos tailings to increase the compatibility between asbestos tailings and polypropylene matrix. Both raw and chemically treated asbestos tailings with different loading levels (from 3 to 30 wt%) were utilized to fabricate composites. Mechanical properties of these composites have been investigated by dynamic mechanical analysis, tensile test and notched impact test. Results showed that hybridization of asbestos tailings in the composites enhanced the mechanical properties of neat PP evidently, and treated asbestos tailings/PP composites yielded even better mechanical properties compared with those of raw asbestos tailings/PP composites. This recycling method of asbestos tailings not only reduces disposal costs and avoids secondary pollution but also produces a new PP-based composite material with enhanced mechanical properties. Copyright © 2014 Elsevier B.V. All rights reserved.

Topological and thermal properties of polypropylene composites based on oil palm biomass

Energy Technology Data Exchange (ETDEWEB)

Bhat, A. H., E-mail: aamir.bhat@petronas.com.my, E-mail: anie-yal88@yahoo.com; Dasan, Y. K., E-mail: aamir.bhat@petronas.com.my, E-mail: anie-yal88@yahoo.com [Department of Fundamental and Applied Sciences, Universiti Teknologi Petronas, 31750 Perak (Malaysia)

2014-10-24

Roughness on pristine and polymer composite surfaces is of enormous practical importance for polymer applications. This study deals with the use of varying quantity of oil palm ash as a nanofiller in a polypropylene based matrix. The oil palm ash sample was preprocessed to break the particles into small diameter by using ultra sonication before using microfluidizer for further deduction in size and homogenization. The oil palm ash was made to undergo many passes through the microfluidizer for fine distribution of particles. Polypropylene based composites containing different loading percentage oil palm ash was granulated by twin screw extruder and then injection molded. The surface morphology of the OPA passed through microfluidizer was analyzed by Tapping Mode - Atomic Force Microscopy (TMAFM). Thermal analysis results showed an increase in the activation energy values. The thermal stability of the composite samples showed improvement as compared to the virgin polymer as corroborated by the on-set degradation temperatures and the temperatures at which 50% degradation occurred.

Non-isothermal kinetic studies on co-processing of olive residue and polypropylene

International Nuclear Information System (INIS)

Aboulkas, A.; El Harfi, K.; El Bouadili, A.

2008-01-01

Co-processing of olive residue with polypropylene was performed in a thermogravimetric analyzer (TGA) reaction system in a nitrogen atmosphere with a view to comparing the process of the mixture with those of the individual components. Experiments were conducted at different heating rates of 2, 10, 20 and 50 K min -1 in the temperature range of 300-975 K based on the results obtained, three thermal stages were identified during the thermal degradation. The first two were dominated by olive residue pyrolysis, while the third was linked to polypropylene pyrolysis, which occurred at much higher temperatures. Discrepancies between the experimental and calculated TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. The maximum degradation temperature of each component in the mixture was higher than those of the individual components alone; thus, an increase in thermal stability was expected. The kinetic processing of thermogravimetric data was conducted using the Friedman method

Topological and thermal properties of polypropylene composites based on oil palm biomass

International Nuclear Information System (INIS)

Bhat, A. H.; Dasan, Y. K.

2014-01-01

Roughness on pristine and polymer composite surfaces is of enormous practical importance for polymer applications. This study deals with the use of varying quantity of oil palm ash as a nanofiller in a polypropylene based matrix. The oil palm ash sample was preprocessed to break the particles into small diameter by using ultra sonication before using microfluidizer for further deduction in size and homogenization. The oil palm ash was made to undergo many passes through the microfluidizer for fine distribution of particles. Polypropylene based composites containing different loading percentage oil palm ash was granulated by twin screw extruder and then injection molded. The surface morphology of the OPA passed through microfluidizer was analyzed by Tapping Mode - Atomic Force Microscopy (TMAFM). Thermal analysis results showed an increase in the activation energy values. The thermal stability of the composite samples showed improvement as compared to the virgin polymer as corroborated by the on-set degradation temperatures and the temperatures at which 50% degradation occurred

Effect of surface modified kaolin on properties of polypropylene grafted maleic anhydride

Science.gov (United States)

Yang, Ni; Zhang, Zuo-Cai; Ma, Ning; Liu, Huan-Li; Zhan, Xue-Qing; Li, Bing; Gao, Wei; Tsai, Fang-Chang; Jiang, Tao; Chang, Chang-Jung; Chiang, Tai-Chin; Shi, Dean

To achieve reinforcement of mechanical and thermal performances of polypropylene (PP) product, this work aimed at fabrication of surface modified kaolin (M-kaolin) filled polypropylene grafted maleic anhydride (PP-g-MAH) composites with varying contents of fillers and investigation of their mechanical and thermal properties. And the prepared PP-g-MAH/M-kaolin composites were characterized by means of Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Fracture analysis by SEM showed M-kaolin particles were well dispersed in the PP-g-MAH matrix. Mechanical behaviors were determined by tensile strength, tensile strain at break and impact strength analysis. Impact strength of PP-g-MAH/2 wt% M-kaolin composites was improved up to 30% comparing with unfilled composites. Thermostability had been found enhanced when M-kaolin added. The results revealed PP-g-MAH/M-kaolin composites showed the optimal thermal and mechanical properties when 2 wt% of M-kaolin was added.

Quick Detection of Contaminants Leaching from Polypropylene Centrifuge Tube with Surface Enhanced Raman Spectroscopy and Ultra Violet Absorption Spectroscopy

OpenAIRE

Xu, Zhida; Liu, Logan

2014-01-01

Anomalous surface enhanced Raman scattering (SERS) peaks are identified for liquid sample stored in polypropylene centrifuge tubes (PP tube) for months. We observed the unexpected Raman peaks during experiments for Thiamine Hydrochloride aqueous solution stored in PP tube for two months. In order to identify the contaminants we have performed SERS experiments for de-ionized water (DI water) stored in polypropylene centrifuge tube for two months and compared them with fresh DI water sample. We...

Mechanical performance of hemp fiber polypropylene composites at different operating temperatures

Science.gov (United States)

Mehdi Tajvidi; Nazanin Motie; Ghonche Rassam; Robert H. Falk; Colin Felton

2010-01-01

In order to quantify the effect of temperature on the mechanical properties of hemp fiber polypropylene composites, formulations containing 25% and 40% (by weight) hemp fiber were produced and tested at three representative temperatures of 256, 296, and 336 K. Flexural, tensile, and impact tests, as well as dynamic mechanical analysis, were performed and the reduction...

Verwendung von Polypropylen/Polyglactin 910- (PP910- und Polypropylen/Polyglecapron 25 (PP25- Netzen bei Beckenbodenprolaps - eine retrospektive Analyse

Directory of Open Access Journals (Sweden)

Schwegler Ch

2009-01-01

Full Text Available Die Entwicklung von Polypropylen- Implantaten zur Behandlung von Bauchwandhernien stellt einen Meilenstein in der Geschichte der Chirurgie dar. Mit einigen Jahren Verzug folgten die Urogynäkologen den Chirurgen und begannen, Polypropylen-Netze zur Behebung von Beckenbodenvorfällen einzusetzen. PP910-Netze (Vypro II®, Ethicon und PP25-Netze (Ultrapro®, Ethicon werden seit Langem mit gutem Erfolg bei Hernien-Operationen eingesetzt. Das Ziel dieser Studie war herauszufinden, inwieweit sich diese beiden Netze auch für den Einsatz beim Beckenbodenprolaps eignen. Hierzu wurden Fragebögen an Patientinnen versandt, denen in den Jahren 2003 und 2004 diese Netze im Beckenboden implantiert wurden. Die Hauptfragestellungen waren hierbei, inwiefern sich die Symptome des Vorfalles nach der Behandlung verändert hatten und welche Komplikationen nach der Operation aufgetreten waren. Beide Gruppen zeigten nach dem Netzeinsatz deutliche Verbesserungen der Symptomatik bei einer geringen Komplikationsquote. Beim Einsatz von PP910 zeigten sich in 6 % der Fälle Komplikationen, die auf die Implantation des Netzes zurückgeführt werden konnten. Beim Einsatz von PP25 zeigten sogar nur 1,5 % der operierten Frauen netzbedingte Komplikationen. Somit hat sich gezeigt, dass beide Netze gut für die Verwendung im Beckenboden geeignet sind. Vergleicht man die beiden Netze mit anderen Produkten, die derzeit als Implantate im Beckenboden genutzt werden, so zeigt sich ein sehr positives Ergebnis mit signifikant weniger postoperativen Komplikationen unter der Verwendung von PP25-Netzen. Im Rahmen dieser Analyse konnte festgestellt werden, dass PP25 ein sehr sicheres Netz mit ausgesprochen guten Ergebnissen für die Therapie des Beckenbodenprolaps ist.

Flow-induced solidification of high-impact polypropylene copolymer compositions : morphological and mechanical effects

NARCIS (Netherlands)

Drongelen, van M.; Gahleitner, M.; Spoelstra, A.B.; Govaert, L.E.; Peters, G.W.M.

2015-01-01

Polypropylene-based impact copolymers are a complex composition of matrix material, a dispersed phase and many optional modifiers. The final heterophasic morphology of such systems is influenced significantly by the processing step, adding an additional level of complexity to understanding the

Thermodynamic Analysis of the Conformational Transition in Aqueous Solutions of Isotactic and Atactic Poly(Methacrylic Acid and the Hydrophobic Effect

Directory of Open Access Journals (Sweden)

Ksenija Kogej

2016-04-01

Full Text Available The affinity of amphiphilic compounds for water is important in various processes, e.g., in conformational transitions of biopolymers, protein folding/unfolding, partitioning of drugs in the living systems, and many others. Herein, we study the conformational transition of two isomer forms of poly(methacrylic acid (PMA, isotactic (iPMA and atactic (aPMA, in water. These isomers are chemically equivalent and differ only in the arrangement of functional groups along the chain. A complete thermodynamic analysis of the transition of the PMA chains from the compact to the extended form (comprising the conformational transition in water in the presence of three alkali chlorides is conducted by determining the free energy, enthalpy, and entropy changes of the process as a function of temperature, and therefrom also the heat capacity change. The heat capacity change of the transition is positive (+20 J/K mol for aPMA and negative (−50 J/K mol for iPMA. This result suggests a different affinity of PMA isomers for water. The conformational transition of iPMA is parallel to the transfer of polar solutes into water, whereas that of aPMA agrees with the transfer of nonpolar solutes into water.

The Optimisation of Processing Condition for Injected Mould Polypropylene-Nanoclay-Gigantochloa Scortechinii based on Melt Flow Index

Science.gov (United States)

Othman, M. H.; Rosli, M. S.; Hasan, S.; Amin, A. M.; Hashim, M. Y.; Marwah, O. M. F.; Amin, S. Y. M.

2018-03-01

The fundamental knowledge of flow behaviour is essential in producing various plastic parts injection moulding process. Moreover, the adaptation of advanced polymer-nanocomposites such as polypropylene-nanoclay with natural fibres, for instance Gigantochloa Scortechinii may boost up the mechanical properties of the parts. Therefore, this project was proposed with the objective to optimise the processing condition of injected mould polypropylene-nanoclay-Gigantochloa Scortechini fibres based on the flow behaviour, which was melt flow index. At first, Gigantochloa Scortechinii fibres have to be preheated at temperature 120°C and then mixed with polypropylene, maleic anhydride modified polypropylene oligomers (PPgMA) and nanoclay by using Brabender Plastograph machine. Next, forms of pellets were produced from the samples by using Granulator machine for use in the injection moulding process. The design of experiments that was used in the injection moulding process was Taguchi Method Orthogonal Array -L934. Melt Flow Index (MF) was selected as the response. Based on the results, the value of MFI increased when the fiber content increase from 0% to 3%, which was 17.78 g/10min to 22.07 g/10min and decreased from 3% to 6%, which was 22.07 g/10min to 20.05 g/10min and 3%, which gives the highest value of MFI. Based on the signal to ratio analysis, the most influential parameter that affects the value of MFI was the melt temperature. The optimum parameter for 3% were 170°C melt temperature, 35% packing pressure, 30% screw speed and 3 second filling time.

Influence of Wind Speed on Heat Flow through Polypropylene Insulating Material

Institute of Scientific and Technical Information of China (English)

SUN Yu-chai; CHENG Zhong-hao; FENG Xun-wei

2006-01-01

The heat transfer properties of polypropylene insulation at different ambient temperature against wind were analysed.A theoretical model of the combined conductive, convective and radiative heat flow through fibrous insulating material was presented. Detail study was carried out by using the finite element method. The theoretical results are in accordance to the experimental results which were accomplished in an artificial climate chamber.

Stability of erythropoietin repackaging in polypropylene syringes for clinical use

Directory of Open Access Journals (Sweden)

Angela Marsili

2017-02-01

Full Text Available Introduction: Epoetin alfa (Eprex® is a subcutaneous, injectable formulation of short half-life recombinant human erythropoietin (rHuEPO. To current knowledge there are no published studies regarding the stability of rHuEPO once repackaging occurs (r-EPO for clinical trial purposes. Materials and methods: We assessed EPO concentration in Eprex® and r-EPO syringes at 0, 60, 90, and 120 days after repackaging in polypropylene syringes. R-EPO was administered to 56 patients taking part in a clinical trial in Friedreich Ataxia. Serum EPO levels were measured at baseline and 48 h after r-EPO administration. Results: No differences were found between r-EPO and Eprex® syringes, but both globally decreased in total EPO content during storage at 4 °C. Patients receiving r-EPO had similar levels in EPO content as expected from previous trials in Friedreich Ataxia and from pharmacokinetics studies in healthy volunteers. Discussion: We demonstrate that repackaging of EPO does not alter its concentration if compared to the original product (Eprex®. This is true both for repackaging procedures and for the stability in polypropylene tubes. The expiration date of r-EPO can be extended from 1 to 4 months after repackaging, in accordance with pharmacopeia rules.

Chemical modification of polypropylene induced by high energy carbon ions

Energy Technology Data Exchange (ETDEWEB)

Saha, A.; Chakraborty, V.; Chintalapudi, S.N. E-mail: snc@gamma.iuc.res.in

2000-06-01

Polypropylene was irradiated with {sup 12}C{sup +} ions of 3.6 and 5.4 MeV energy using 3 MV Pelletron. The spectral changes owing to ion bombardment were investigated by UV-VIS and Fourier-transform infrared (FTIR) spectroscopy. A gradual increase in absorbance was observed around visible and near visible region with increase in fluence of bombarding ions. The difference absorption spectra show formation of chromophoric groups with wavelength maximum near 380 nm at lower fluence, but at high fluence a shift in peak is observed. The chromophoric groups are likely to be the extended conjugated polyene system and the red shift in peak position at high fluence may be attributed to the greater degree of conjugation. The formation of unsaturated linkage is confirmed by the FTIR spectra with observed stretching band around 1650 cm{sup -1} and its intensity was found to increase with increase in ion fluence studied. The gases (in the range 2-80 amu) which were evolved due to interaction of polypropylene with {sup 12}C{sup +} ions were measured with Residual Gas Analyzer (RGA). A large number of gaseous components were detected. This shows that polymer chains break into some smaller fragments which concomitantly leads to extended conjugation.

Structural characterization and mechanical properties of polypropylene reinforced natural fibers

Science.gov (United States)

Karim, M. A. A.; Zaman, I.; Rozlan, S. A. M.; Berhanuddin, N. I. C.; Manshoor, B.; Mustapha, M. S.; Khalid, A.; Chan, S. W.

2017-10-01

Recently the development of natural fiber composite instead of synthetics fiber has lead to eco-friendly product manufacturing to meet various applications in the field of automotive, construction and manufacturing. The use of natural fibers offer an alternative to the reinforcing fibers because of their good mechanical properties, low density, renewability, and biodegradability. In this present research, the effects of maleic anhydride polypropylene (MAPP) on the mechanical properties and material characterization behaviour of kenaf fiber and coir fiber reinforced polypropylene were investigated. Different fractions of composites with 10wt%, 20wt% and 30wt% fiber content were prepared by using brabender mixer at 190°C. The 3wt% MAPP was added during the mixing. The composites were subsequently molded with injection molding to prepare the test specimens. The mechanical properties of the samples were investigated according to ISO 527 to determine the tensile strength and modulus. These results were also confirmed by the SEM machine observations of fracture surface of composites and FTIR analysis of the chemical structure. As the results, the presence of MAPP helps increasing the mechanical properties of both fibers and 30wt% kenaf fiber with 3wt% MAPP gives the best result compare to others.

Enhancement in Mechanical and Electrical Properties of Polypropylene Using Graphene Oxide Grafted with End-Functionalized Polypropylene

Directory of Open Access Journals (Sweden)

Patchanee Chammingkwan

2016-03-01

Full Text Available Terminally hydroxylated polypropylene (PP synthesized by a chain transfer method was grafted to graphene oxide (GO at the chain end. Thus obtained PP-modified GO (PP-GO was melt mixed with PP without the use of a compatibilizer to prepare PP/GO nanocomposites. Mechanical and electrical properties of the resultant nanocomposites and reference samples that contained graphite nanoplatelets, partially reduced GO, or fully reduced GO were examined. The best improvement in the tensile strength was obtained using PP-GO at 1.0 wt %. The inclusion of PP-GO also led to the highest electrical conductivity, in spite of the incomplete reduction. These observations pointed out that terminally hydroxylated PP covalently grafted to GO prevented GO layers from re-stacking and agglomeration during melt mixing, affording improved dispersion as well as stronger interfacial bonding between the matrix and GO.

Evaluation of Mechanical Property of Carbon Fiber/Polypropylene Composite According to Carbon Fiber Surface Treatment

International Nuclear Information System (INIS)

Han, Song Hee; Oh, Hyun Ju; Kim, Seong Su

2013-01-01

In this study, the mechanical properties of a carbon fiber/polypropylene composite were evaluated according to the carbon fiber surface treatment. Carbon fiber surface treatments such as silane coupling agents and plasma treatment were performed to enhance the interfacial strength between carbon fibers and polypropylene. The treated carbon fiber surface was characterized by XP S, Sem, and single-filament tensile test. The interlaminar shear strength (Ilks) of the composite with respect to the surface treatment was determined by a short beam shear test. The test results showed that the Ilks of the plasma-treated specimen increased with the treatment time. The Ilks of the specimen treated with a silane coupling agent after plasma treatment increased by 48.7% compared to that of the untreated specimen

Mechanical and thermal properties of physically-blended-plastic films

International Nuclear Information System (INIS)

Abu Issa, M. S.

1983-10-01

Low density polyethylene (LDPE) and isotactic polypropylene (PP) blend were produced in film form and were characterized by a number of techniques such as wide-angle x-ray diffraction (WAXD), differential thermal analysis (DTA), scanning electron microscopy (SEM), and instron tensile testing. Results of WAXD and DTA showed conclusively that the two components in the blend are incompatible. SEM micrographs indicated that the 60/40 and 40/60 PP/PE blends show approximately fine homogeneous dispersion of the minor component into the matrix of the major component. The mechanical properties of the blend films improved with respect to the PE homo polymer. The improvement was more remarkable with the increase of the PP component in the blend. Results obtained in this work were explained in terms of crystallinity and the crystallite orientation. 28 refs., 29 figs., 5 tabs. (A.M.H.)

Decontamination of polypropylene fabrics by dry cleaning

International Nuclear Information System (INIS)

Severa, J.; Knajfl, J.

1983-01-01

Polypropylene fabrics can efficiently be decontaminated by dry cleaning in benzine or perchloroethylene, this also in case the fabric was greased in addition to radioactive contamination. For heavily soiled fabric, it is advantageous to first dry clean it and then wash it. The positive effect was confirmed of intensifiers on the cleaning process, especially of benzine soap. In practice, its concentration should be selected within 1 and 10 g.dm - 3 . Decontamination by dry cleaning and subsequent washing is advantageous in that that the resulting activity of waste water from the laundry is low. Radioactive wastes from the dry cleaning process have a low weight and can be handled as solid waste. (M.D.)

Flexural creep behaviour of jute polypropylene composites

Science.gov (United States)

Chandekar, Harichandra; Chaudhari, Vikas

2016-09-01

Present study is about the flexural creep behaviour of jute fabric reinforced polypropylene (Jute-PP) composites. The PP sheet and alkali treated jute fabric is stacked alternately and hot pressed in compression molding machine to get Jute-PP composite laminate. The flexural creep study is carried out on dynamic mechanical analyzer. The creep behaviour of the composite is modeled using four-parameter Burgers model. Short-term accelerated creep testing is conducted which is later used to predict long term creep behaviour. The feasibility of the construction of a master curve using the time-temperature superposition (TTS) principle to predict long term creep behavior of unreinforced PP and Jute-PP composite is investigated.

Functional Block Copolymers as Compatibilizers for Nanoclays in Polypropylene Nanocomposites

DEFF Research Database (Denmark)

Jankova Atanasova, Katja; Daugaard, Anders Egede; Stribeck, Norbert

2011-01-01

With the aim of creating tough nanocomposits (NC) [1] based on polypropylene (PP) and nanoclay (NCl) in the framework of the 7th EU program NANOTOUGH we have designed amphiphilic block copolymers utilizing Atom Transfer Radical Polymerization (ATRP) [2]. They consist of a hydrophobic block...... crystallites) is replaced by alien-reinforcement (of the MMT). Furthermore, the results from the impact strength and cyclic test of the prepared PP nanocomposites [3] are promicing....

Stability of busulfan solutions in polypropylene syringes and infusion bags as determined with an original assay.

Science.gov (United States)

Guichard, Nicolas; Bonnabry, Pascal; Rudaz, Serge; Fleury-Souverain, Sandrine

2017-11-15

The stability of busulfan solution in 0.9% sodium chloride and stored in polypropylene syringes or infusion bags was evaluated. Busulfan solutions (0.54 mg/mL) were prepared and transferred to 50-mL polypropylene syringes and 100- and 500-mL polypropylene infusion bags and stored at 2-8 and 23-27 °C. Chemical stability was measured using a stability-indicating, ultrahigh performance liquid chromatography coupled to mass spectrometry method. The stability of busulfan was assessed by measuring the percentage of the initial concentration remaining at the end of each time point of analysis. The initial busulfan concentration was defined as 100%. Stability was defined as retention of at least 90% of the initial busulfan concentration. A visual inspection of the samples for particulate matter, clarity, and color without instrumentation of magnification was conducted at each time point of analysis. The visual inspection demonstrated no influence of the storage container when busulfan infusions diluted in 0.9% sodium chloride injection were stored at 23-27 °C. No color change or precipitate was observed at this temperature; however, a rapid decrease of the busulfan content in all containers stored at room temperature was observed. Busulfan in syringes was chemically stable for 12 hours, while busulfan in infusion bags (100 and 500 mL) was stable only for 3 hours at 23-27 °C. Busulfan 0.54-mg/mL solution in 0.9% sodium chloride injection was physically and chemically stable for 30 hours when stored in 50-mL polypropylene syringes at 2-8 °C and protected from light. Copyright © 2017 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

[Study on the interface of human hepatocyte/micropore polypropylene ultrafiltration membrane].

Science.gov (United States)

Peng, Cheng-Hong; Han, Bao-San; Gao, Chang-You; Ma, Zu-Wei; Zhao, Zhi-Ming; Wang, Yong; Liu, Hong; Zhang, Gui-di; Yang, Mei-Juan

2004-09-02

To found a new interface of human hepatocyte/micropore polypropylene ultrafiltration membrane (MPP) with good cytocompatibility so as to construct bioartificial bioreactor with polypropylene hollow fibers in future. MPP ultrafiltration membrane underwent chemical grafting modification through ultraviolet irradiation and Fe(2+) reduction. The contact angles of MPP and the modified MPP membranes were measured. Human hepatic cells L-02 were cultured. MPP and modified MPP membranes were spread on the wells of culture plate and human hepatic cells and cytodex 3 were inoculated on them. Different kinds of microscopy were used to observe the morphology of these cells. The water contact angle of MPP and the modified MPP membranes decreased from 78 degrees +/- 5 degrees to 27 degrees +/- 4 degrees (P < 0.05), which indicated that the hydrophilicity of the membrane was improved obviously after the grafting modification. Human hepatocyte L-02 did not adhere to and spread on the modified MPP membrane surface, and only grew on the microcarrier cytodex 3 with higher density and higher proliferation ratio measured by MTT. Grafting modification of acrylamide on MPP membrane is a good method to improve the human hepatocyte cytocompatibility with MPP ultrafiltration membrane.

Evaluation of the acquirement of nano composites of polypropylene and a bentonite organophilized by different methodologies

International Nuclear Information System (INIS)

Paiva, Lucilene B. de; Morales, Ana R.; Branciforti, Marcia C.; Bretas, Rosario E.S.

2009-01-01

This work describes the organophilization of an argentinean sodium bentonite with a quaternary ammo nium salt, by two methodologies: cation exchange in aqueous dispersion and intercalation in semi-solid medium. The modified samples were used in the preparation of nano composites, with polypropylene as a matrix and polypropylene-graft-maleic anhydride as a coupling agent, through melt intercalation by using a twin-screw micro extruder. The organophilic bentonites were characterized by the swelling capacity test in water and in xylene and by X-ray diffraction, and the nano composites were characterized by X-ray diffraction and transmission electronic microscopy. The results showed that were obtained nano composites with structures partially intercalated and exfoliated. (author)

Spatially Resolved Characterization of Cellulose Nanocrystal-Polypropylene Composite by Confocal Raman Microscopy

Science.gov (United States)

Umesh P. Agarwal; Ronald Sabo; Richard S. Reiner; Craig M. Clemons; Alan W. Rudie

2012-01-01

Raman spectroscopy was used to analyze cellulose nanocrystal (CNC)–polypropylene (PP) composites and to investigate the spatial distribution of CNCs in extruded composite filaments. Three composites were made from two forms of nanocellulose (CNCs from wood pulp and the nanoscale fraction of microcrystalline cellulose) and two of the three composites investigated used...

Prediction of yield and long-term failure of oriented polypropylene: kinetics and anisotropy

NARCIS (Netherlands)

van Erp, T.B.; Reynolds, C.T.; Peijs, T.; van Dommelen, J.A.W.; Govaert, L.E.

2009-01-01

The time-dependent yield and failure behavior of off-axis loaded uniaxially oriented polypropy-lene tape is investigated. The yield and failure behavior is described with an anisotropic vis-coplastic model. A viscoplastic flow rule is used with an equivalent stress, based on Hill’sanisotropic yield

Stone-ground wood pulp-reinforced polypropylene composites: Water uptake and thermal properties

Directory of Open Access Journals (Sweden)

Joan Pere López

2012-11-01

Full Text Available Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC and thermogravimetric analysis (TGA were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC.

Rheological, Colour and Processing Properties of Polypropylene Masterbatches for Nanocomposite Fibre Preparation

Directory of Open Access Journals (Sweden)

Štefan Krivoš

2017-12-01

Full Text Available Asia’s current dominance of the global production of standard types of chemical fibres requires the sophistication of European fibre and textile products. Modifying the mass or surface of materials using nanotechnologies is one of the most promising ways to ensure the special, mono- and multi-functionally modified fibre properties of clothing and technical textiles. The permanent antimicrobial treatment of fibre mass represents one the most desired functional modifi cations of chemical fibres. It involves the use of an antimicrobial additive masterbatch with the appropriate rheological, colour and processing properties required for the preparation of antimicrobial modified fibres. This article presents the results of our study of the effect of two types of nanoadditives (nanosilica and nanocalcium carbonate as potential carriers of an AMB active ingredient, and the effect of stearic acid, polyethylene glycol and propylene oxide as various dispersing systems on the rheological, colour and processing properties of polypropylene nanoadditive masterbatches. The obtained experimental results are evaluated in terms of the suitability of the properties of prepared nanoadditive masterbatches for the preparation of nanocomposite polypropylene fibres.

Processing and Characterization of a Polypropylene Biocomposite Compounded with Maleated and Acrylated Compatibilizers

Directory of Open Access Journals (Sweden)

Brent A. Nerenz

2012-01-01

Full Text Available Polypropylene (PP biocomposites containing 20 wt.% sunflower hull as a particulate reinforcement were compounded and tested under tensile, flexural, and impact loadings. The incorporation of the sunflower hull without compatibilizer resulted in diminished tensile strength and impact energy absorption but increased flexural strength and both tensile modulus and flexural modulus when compared to neat PP. Formulations containing three different chemical compatibilizers were tested to determine their effectiveness in improving the interfacial adhesion between the fiber surface and PP chains. Maleic anhydride grafted with PP (MA-g-PP achieved greater improvements in tensile strength but reduced impact strength in comparison to an acrylic-acid-grafted PP compatibilizer (AA-g-PP. The molecular weight, graft level, and the ability to affect strength, modulus, and absorbed impact energy were also investigated for the compatibilizers. A MA-g-PP having high molecular weight and low graft level was most effective in improving the investigated properties of a sunflower hull-reinforced polypropylene biocomposite.

Rheological and mechanical properties of polypropylene prepared with multi-walled carbon nanotube masterbatch.

Science.gov (United States)

Shim, Young-Sun; Park, Soo-Jin

2012-07-01

In this study, the effects of polypropylene-grafted maleic-anhydride-treated multi-walled carbon nanotubes (PP-MWNTs) on the viscoelastic behaviors and mechanical properties of a polypropylene-(PP)-based composite system were examined. The PP-MWNT/PP composites were prepared via melt mixing with a 3:1 ratio of PP-g-MA and acid-treated MWNTs at 220 degrees C. The surface characteristics of the PP-MWNTs were confirmed via Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). The viscoelastic behavior and mechanical properties of the PP-MWNT/PP composites were confirmed using a rheometer and an ultimate testing machine (UTM). The storage and loss moduli increased with increasing PP-MWNT content. The critical intensity stress factor (K(IC)) of the PP-MWNT/PP composites at high filler loading was also higher than that of the MWNT/PP composites. In conclusion, the viscoelastic behavior and mechanical properties of MWNT/PP can be improved by grafting MWNTs to PP-g-MA.

Comparison of post-operative wound infection after inguinal hernia repair with polypropylene mesh and polyester mesh

International Nuclear Information System (INIS)

Mughal, M.A.; Ahmed, M.; Sajid, M.T.; Mustafa, Q.U.A.; Shukr, I.; Ahsan, J.

2012-01-01

Objective: To compare post operative wound infection frequency after inguinal hernia repair with polypropylene and polyester mesh using standard Lichtenstein hernioplasty technique. Study Design: Randomized controlled trial. Place and Duration: This study was conducted at general surgery department CMH/MH Rawalpindi from 8th April 2007 to 1st Jan 2008 over a period of 09 months. Patients and Materials: Sixty patients received through outpatient department with diagnosis of inguinal hernia satisfying inclusion/exclusion criteria were included. Patients were divided into two groups randomly. Group 1 included those patients in whom polypropylene mesh was used while group II patients were implanted with polyester mesh. Demographic as well as data concerning post operative wound infection was collected and analyzed. Results: Fifty seven patients (95%) were males while remaining (05%) were females. Mean age in group I was 41.17+-9.99 years while in group II was 41.47+-9.79 years (p=0.907). One patient (3.3%) in each group developed wound infection diagnosed by clinical evidence of pain at wound site, redness, induration and purulent discharge. Conclusion: There is no difference in post operative wound infection rate after inguinal Lichtenstein hernioplasty using either polypropylene or polyester mesh. (author)

Effect of polypropylene maleic anhydride (PPMAH) on mechanical and morphological properties of polypropylene (PP)/recycled acrylonitrile butadiene rubber (NBRr)/empty fruit bunch (EFB) composites

Science.gov (United States)

Othman, Nurul Syazwani; Santiagoo, Ragunathan; Abdillahi, Khalid Mohamed; Ismail, Hanafi

2017-07-01

The fabrication of polypropylene (PP)/ recycled acrylonitrile butadiene rubber (NBRr)/ empty fruit bunch (EFB) composites were investigated. The effects of polypropylene maleic anhydride (PPMAH) as a compatibilizer on the mechanical and morphological properties of PP/NBRr/EFB composites were studied. Composites were prepared through melt mixing using heated two roll mill at 180 °C for 9 minutes and rotor speed of 15 rpm. NBRr loading were varied from 0 to 60 phr and PPMAH was fixed for 5 phr. The composites were moulded into a 1 mm thin sheet using hot press machine and then cut into dumbbell shape. The mechanical and morphological properties of composites were examined using universal tensile machine (UTM) and scanning electron microscope (SEM), respectively. Tensile strength and Young's modulus of PP/NBRr/EFB composites decreased with increasing NBRr loading, whilst increasing the elongation at break. However, PPMAH compatibilized composites have resulted 27% to 40% and 25% to 42% higher tensile strength and Young's modulus, respectively, higher compared to uncompatibilized composites. This was due to the better adhesion between PP/NBRr matrices and EFB filler with the presence of maleic anhydride moieties. From the morphological study, the micrograph of PPMAH compatibilized composites has proved the well bonded and good attachments of EFB filler with PP/NBRr matrices which results better tensile strength to the PP/NBRr/EFB composites.

PEG-template for surface modification of zeolite: A convenient material to the design of polypropylene based composite for packaging films

Science.gov (United States)

Toommee, S.; Pratumpong, P.

2018-06-01

Zeolite was successfully modified by conventional synthetic route. Polyethylene glycol was employed for surface modification of zeolite. The surface of zeolite exhibited therefore hydrophobic properties. Less than 5 wt% of modified zeolites with uniform size and shape were integrated into polypropylene matrix. Mechanical properties of composite exhibited the similar trend compare to neat polypropylene. Oxygen transmission rate and water vapor transmission rate were evaluated and it exhibited the strong potential to be a good candidate material in active packaging.

Facial reconstruction using polypropylene mesh after resection of maxillary ossifying fibroma

Directory of Open Access Journals (Sweden)

R. Soesanto

2012-09-01

Full Text Available Background: Ossifying fibroma is a variant of fibrous dysplasia and catagorized as osteofibrosis lesion. It commonly affects long bones but occasionally involves jaws. Mandible affected more common than maxilla. The treatment of ossifying fibroma include excision and resection. Excision of lesion and resection of maxilla could cause facial defect which cannot be reconstructed with bone graft. Purpose: The aim of this case report is to report the potential use of polypropylene mesh in facial reconstruction after hemimaxillectomy in patients diagnosed with ossifying fibroma of the maxilla. Case: A 17-years-old female patient came to Oral and Maxillofacial Surgery clinic, Dental Hospital, Faculty of Dentistry, Airlangga University, with chief complaint of swelling in the upper left cheek of 2 years duration which was not related to any history of toothache. Patient also complained of the itchiness and pain on the swelling area occasionally as well as salty discharge from the mass. The FNA was done and the citology result indicated a benign mesenchimal tumor. Incisonal biopsy was subsequently performed and the histopathology report confirmed the diagnosis of cementifying fibroma. Case management: Left hemimaxillectomy was done, and post surgical defect in the facial and buccal aspect was immediately reconstructed using three layers of polypropylene mesh. On follow-up, eleven months post-operatively, the patient was well and there was no facial deformity or asymmetry. Conclusion: Polypropylene mesh is a potential material for facial reconstruction as it can reduce the risk of facial deformity after hemimaxillectomy of patients with tumor of the maxilla.Latar belakang: Ossifying fibroma merupakan varian dari fibrous dysplasia dan termasuk di dalam kategori lesi osteofibrosis. Umumnya mengenai tulang panjang tetapi dapat juga mengenai rahang dan lebih banyak menyerang tulang mandibula dibanding maksila. Perawatan ossifying fibroma dilakukan dengan

Effect of Polypropylene Modification by Impregnation with Oil on Its Wear and Friction Coefficient at Variable Load and Various Friction Rates

Directory of Open Access Journals (Sweden)

Paweł Sędłak

2017-01-01

Full Text Available Laboratorial two-body wear testing was carried out in order to assess effects of polypropylene modification by impregnating it with oils on friction coefficient and wear in comparison to those parameters of unmodified polypropylene, Teflon, and polyamide during operation under conditions of sliding friction without lubrication. Wear behaviour of the tested specimens was investigated using ASTM G77-98 standard wear test equipment. Recording program made it possible to visualise and record the following parameters: rotational speed and load, linear wear, friction coefficient, temperature of the specimen, and ambient temperature. In addition, wear mechanisms of the analysed materials were determined with use of scanning electron microscopy. In the case of the remaining tested polymers, the most important mechanism of wear was adhesion (PP, PTFE, PA 6.6, and PA MoS2, microcutting (PTFE, PA 6.6, and PA MoS2, fatigue wear (PTFE, forming “roll-shaped particles” combined with plastic deformation (PA 6.6 and PA MoS2, and thermal wear (PP. Impregnation of polypropylene with engine oil, gear oil, or RME results in significant reduction of friction coefficient and thus of friction torque, in relation to not only unmodified polypropylene but also the examined polyamide and Teflon.

Surface modifications of polypropylene by high energy carbon ions

International Nuclear Information System (INIS)

Saha, A.; Chakraborty, V.; Dutta, R.K.; Chintalapudi, S.N.

2000-01-01

Polypropylene was irradiated with 12 C ions of 3.6 and 5.4 MeV energies using 3 MV tandem accelerator. The surface modification was investigated by Scanning Electron Microscopy (SEM). Optical changes were monitored by UV-VIS and FTIR spectroscopy. At the lowest ion fluence, only blister formation of various sizes (1-6 μm) was observed. Polymer when irradiated at a fluence of 1x10 14 ions/cm 2 exhibited a network structure. A comparative study on dose dependence of surface and bulk modification has been described. (author)

Current development of Green IPPs: experiences, challenges, and strategies. Workshop of the EC-ASEAN Green Independent Power Producers Network, 15th of Sept., 2005 in Karlsruhe

OpenAIRE

Rentz, Otto; Möst, Dominik; Eßer, Anke [Hrsg.

2005-01-01

Due to growing environmental issues, a strong political will to increase the use of renewable energy sources exists in many countries of the world. Mainly in the EU, measures to promote renewable energies have been taken. In Asia, the use of renewable energy is being promoted, too. However, policies as well as markets are still rather in the fledging stages. Therefore, a network on Green Independent Power Producers (GrIPPs) was set up, to exchange experiences between Europe and Southeast Asia...

High improvement in trap level density and direct current breakdown strength of block polypropylene by doping with a β-nucleating agent

Science.gov (United States)

Zhang, Chong; Zha, Jun-Wei; Yan, Hong-Da; Li, Wei-Kang; Dang, Zhi-Min

2018-02-01

Polypropylene is one kind of eco-friendly insulating material, which has attracted more attention for use in high voltage direct current (HVDC) insulation due to the long-distance transmission, low loss, and recyclability. In this work, the morphology and thermal and electrical properties of the block polypropylene with various β-nucleating agent (β-NA) contents were investigated. The relative fraction of the β-crystal can reach 64.7% after adding 0.05 wt. % β-NA. The β-NA also greatly reduced the melting point and improved the crystallization temperature. The electrical property results showed that the alternating and direct current breakdown strength and conduction current were obviously improved. In addition, space charge accumulation was significantly suppressed by introducing the β-NA. This work provides an attractive strategy of design and fabrication of polypropylene for HVDC application.

Ag2S deposited on oxidized polypropylene as composite material for solar light absorption

NARCIS (Netherlands)

Krylovaa, V.; Milbrat, Alexander; Embrachts, A.; Baltrusaitis, Jonas

2014-01-01

Thin film metal chalcogenides are superior solar light absorbers and can be combined into a functional material when deposited on polymeric substrates. Ag2S composite materials were synthesized on oxidized polypropylene using chemical bath deposition method and their properties were explored using

Functionalized Poly(propylene imine) Dendrimers as Novel Phase Transfer Catalyst in Supercritical Cabon Dioxide

NARCIS (Netherlands)

Goetheer, E.L.V.; Baars, M.W.P.L.; Broeke, van den L.J.P.; Meijer, E.W.; Keurentjes, J.T.F.

2000-01-01

Perfluoro-functionalized poly(propylene imine) dendrimers have been used as reactive extractants for anionic species and as phase transfer catalysts for two types of reactions. Different generations of dendrimers have been used for applications in carbon dioxide. First, the reactive extraction of

Mechanical and thermal properties of polypropylene composites with curaua fibre irradiated with gamma radiation

International Nuclear Information System (INIS)

Egute, Nayara S.; Forster, Pedro L.; Parra, Duclerc F.; Fermino, Danilo M.; Santana, Sebastiao; Lugao, Ademar B.

2009-01-01

Thermal and mechanical behavior of polypropylene with curaua fibre composites were investigated. The treatment of the curaua fibres was processed in alkaline solution (10% wt NaOH). A coupling agent was used (maleic anhydride) to increase the adhesion of the fibre/matrix interface. This composite was irradiated with gamma source in the doses of 5, 15 and 30 kGy and the adhesion between the fibres and the polymeric matrix was monitored to observe probable changes. The thermal behavior was evaluated using differential scanning calorimetry (DSC) and Thermogravimetry (TGA). The mechanical behavior was evaluated using tensile strength in comparison with non-reinforced polypropylene resin. The morphology of the composite fracture surface was observed using scanning electron microscopy (SEM). There were no significant changes in the thermal properties neither in the adhesion of irradiated fibres at doses of 5, 15 and 30 kGy of gamma radiation. (author)

The effect of gamma irradiation on the thermal expansion behaviour of oriented polypropylene

International Nuclear Information System (INIS)

Godjevargov, L.; Novakovic, L.J.; Kostoski, D.

1991-01-01

Quenched and air-cooled samples of oriented polypropylene have been irradiated to 300 kGy adsorbed dose in the presence of air. The parallel thermal expansion coefficient decreases and becomes negative with increasing orientation. The effect of adsorbed dose on the thermal expansion behaviour is practically negligible. (author) 4 refs.; 4 figs

Polypropylene Nanocomposites Obtained by In Situ Polymerization Using Metallocene Catalyst: Influence of the Nanoparticles on the Final Polymer Morphology

Directory of Open Access Journals (Sweden)

Paula Zapata

2012-01-01

Full Text Available Polypropylene nanocomposites containing silica nanospheres based on the sol-gel methods were produced via in situ polymerization using a rac-Et(Ind2ZrCl2/methylaluminoxane (MAO system. Two different routes were used depending on the interaction between the silica nanoparticles with the catalytic system. In route 1 the nanoparticles were added together with the catalytic system (rac-Et(Ind2ZrCl2/(MAO directly into the reactor, and in route 2 the metallocene rac-Et(Ind2ZrCl2 was supported on silica nanospheres pretreated with (MAO. SEM images show that when the nanospheres were added by both routes, they were replicated in the final polymer particle morphology; this phenomenon was more pronounced for PP obtained by route 2. The polypropylene (PP nanocomposites obtained by both routes had a slightly higher percent crystallinities and crystallinity temperatures than pure PP. Transmission electron microscopy (TEM images show that the nanospheres were well dispersed into the polypropylene matrix, particularly in the nanocomposites obtained by the support system (route 2.

Improving the environment for weaned piglets using polypropylene fabrics above the animals in cold periods.

Science.gov (United States)

Dolz, Noé; Babot, Daniel; Álvarez-Rodríguez, Javier; Forcada, Fernando

2015-12-01

This study aimed at evaluating the use of polypropylene fabrics in weaned pig facilities (5-10 weeks of age) during the winter period to improve thermal environment and energy saving for heating. Two experiments were conducted to validate the effects of fabrics (F) compared to control (C) in three 2-week periods using natural ventilation (assay 1, 2013) and forced ventilation (assay 2, 2014). Air temperature was greater in F than in C compartments in both years, particularly during the first 2-week periods (2 °C of mean difference). Natural ventilation was not enough to maintain relative humidity levels below 70 % at the end of the postweaning period (9-10 weeks of age) in both groups (F and C), whereas forced ventilation allowed controlling daily mean relative humidity levels <60 %. About 12-26 % of the radiant heat was transmitted through the fabrics cover, depending on the wavelength. There were no differences on growth performance of piglets in the two compartments in both years. The use of polypropylene fabrics was associated with a significant electric energy saving for heating during the first (data available only in 2014) and second 2-week period in both years. In conclusion, polypropylene fabrics may be an interesting tool to provide optimal environmental conditions for weaned piglets in winter, especially during the two first weeks after weaning. Their transmittance properties allow trapping infrared emission produced by the piglets and heating, avoiding heat losses through the roof, and therefore saving heating energy.

Effect of coupling agent on durian skin fibre nanocomposite reinforced polypropylene

Science.gov (United States)

Siti Nur E'zzati, M. A.; Anuar, H.; Siti Munirah Salimah, A. R.

2018-01-01

This paper reports on the development of a composite-based natural fiber to reduce the reliance on petroleum-based product in order to amplify environmental awareness. The production of Durian Skin Nanofiber (DSNF) was conducted using biological fermentation method via rhizopus oryzae in order to obtain the nano dimension of the particle size. Polypropylene (PP) and DSNF were produced using Haake internal mixer via melt blending technique. The significant effect of maleic anhydride grafted polypropylene (MAPP) on the properties of PP/DSNF nanocomposite was investigated to study its mechanical properties which are tensile strength and thermal stability using thermogravimetric (TGA) and differential scanning analysis (DSC). The tensile property of PP nanocomposites increased from 33 MPa to 38 MPa with the presence of MAPP. The addition of MAPP also increased the thermal stability of PP/DSNF nanocomposite where the char residue increased by 52%. Besides that, the thermal degradation of PP/DSNF and PP/DSNF-MAPP were higher than PP where they exerted higher amount of weight loss at an elevated temperature. The percentage of crystallinity, %Xc, of PP nanocomposites improved with the addition of MAPP by 35% based on the differential scanning calorimetry (DSC) result. The SEM analysis showed that the PP/DSNF-MAPP exerts ductile fracture while PP/DSNF exerts brittle fracture.

Effects of gamma irradiation on food contact polyethylene, polypropylene and polystyrene: additives and other chemicals

International Nuclear Information System (INIS)

Kawamura, Yoko; Sayama, Kayo; Yamada, Takashi

2000-01-01

The effects of gamma irradiation on additives, oligomers, and other chemicals in food contact polyethylene, polypropylene and polystyrene were investigated. Polyethylene and polypropylene products contained several antioxidants, lubricants and plasticizers. After gamma irradiation, the contents of all the antioxidants significantly decreased. Irgafos 168 disappeared the fastest. Lubricants and plasticizers decreased to some extent or not at all. 2,4-Di-tert-butylphenol was detected not only after irradiation but also before irradiation, and 1,3-di-tert-butylbenzene and 2,6-di-tert-butyl-1,4-benzoquinone were detected only after irradiation. They were presumed to be degradation products of the irradiation, though the former should be also a degradation product of the manufacturing process. On the other hand, the polystyrene products contained styrene dimers and trimers and their contents did not change after the gamma irradiation. (author)

Feasibility of the recovery of uranium from alkaline waste by amidoximated grafted polypropylene polymer matrix

International Nuclear Information System (INIS)

Misra, S.K.; Gandhi, P.M.; Bhardwaj, Y.K.

2013-01-01

The amidoximated grafted polypropylene polymer matrix was prepared by post irradiation grafting of acrylonitrile (AN) onto thermally bonded non-woven matrix of poly(propylene) sheet using electron beams. This precursor polymer was reacted with hydroxylamine to convert AN to poly(acrylamidoxime) (AO) groups, and conditioned by treating them with 2.5 % KOH at 80 deg C for 1 h. The polymer matrix was having the degree of AN grafting ∼106 wt% and its subsequent conversion to AO groups ∼70 %. The water uptake capacity of AO polymer matrix were found to be 100 ± 5 % (w/w). Quantitative recovery of uranium from alkaline waste (ammonium diuranate supernatant) solution was achieved by this polymer matrix. The other radionuclides present in the waste solution were not extracted by the polymer matrix. For all other radionuclides, the uptake was found to be <6 %. (author)

Effect of Nano-clay on Rheological and Extrusion Foaming Process of a Block-Copolymerized Polypropylene

Directory of Open Access Journals (Sweden)

Wang Mingyi

2016-01-01

Full Text Available The effects of nano-clay and the corresponding coupling agent maleic anhydride grafted polypropylene (PP-g-MAH on thermal properties, rheological properties and extrusion foaming process of a block-copolymerized polypropylene (B-PP were studied. Supercritical CO2 (SC CO2 was used as the foaming agent with a concentration of 5wt%. Each step of foamed B-PP/ PP-g-MAH/ nano-clay composites processing is addressed, including mixing of the composites, manufacture of the composites, foaming process of the composites and characterization of the cell structure. The results showed that incorporation of nano-clay and PP-g-MAH caused reduced melt strength and complex viscosity of B-PP. However, the heterogeneous nucleation induced by nano-clay and PP-g-MAH improved the maximum foaming expansion ratio and cell-population density of B-PP foam.

Production of sorption-active polypropylene fibers by radiation-induce grafting of glycidyl methacrylate as a precursor monomer

International Nuclear Information System (INIS)

Bondar, Yu.V.; Kim, H.J.; Lim, Y.J.; Kravets, L.I.

2004-01-01

Full text: Two types of sorption-active polypropylene fiber carrying strong-acid sulfonate groups and amino groups have been synthesized by radiation-induced graft polymerization of glycidyl methacrylate (GMA) with subsequent chemical modification of the epoxy groups of poly-GMA graft chains. The effect of various polymerization parameters on the GMA grafting degree was investigated in detail. The epoxy ring-opening of poly-GMA graft chains with introduction of strong-acid sulfonate groups was carried out with sodium hydrogen sulfite in water-dimethylformamide solution at 70 o C. The main peculiarities of the sulfonation reaction in depending on the reaction time and GMA grafting degree have been investigated. It was shown that for the samples with GMA grafting degree more than 50% two simultaneous processes take place during the sulfonation reaction, namely the incorporation of the sulfonate groups via opening of the GMA epoxy-rings as well as hydrolysis of the GMA epoxy-rings with the formation of α-glycol groups. Amine groups were incorporated by treatment of GMA-grafted polypropylene fibers with excess of diethylene triamine reagent. The conversion of the epoxy groups into the functional groups was investigated as a function of the degree of GMA grafting and reaction time. The ion-exchange characteristics of obtained sorption-active polypropylene fibers were determined

Production of sorption-active polypropylene fiber by radiation-induce grafting of glycidyl methacrylate as a precursor monomer

International Nuclear Information System (INIS)

Bondar, Yu.V.; Kim, H.J.; Lim, Y.J.; Kravets, L.I.

2004-01-01

Two types of sorption-active polypropylene fiber carrying strong-acid sulfonate groups and amino groups have been synthesized by radiation-induced graft polymerization of glycidyl methacrylate (GMA) with subsequent chemical modification of the epoxy groups of poly-GMA graft chains. The effect of various polymerization parameters on the GMA grafting degree was investigated in detail. The epoxy ring-opening of poly-GMA graft chains with introduction of strong-acid sulfonate groups was carried out with sodium hydrogen sulfite in water-dimethylformamide solution at 70 o C. The main peculiarities of the sulfonation reaction in depending on the reaction time and GMA grafting degree have been investigated. It was shown that for the samples with GMA grafting degree more than 50% two simultaneous processes take place during the sulfonation reaction, namely the incorporation of the sulfonate groups via opening of the GMA epoxy-rings as well as hydrolysis of the GMA epoxy-rings with the formation of α-glycol groups. Amine groups were incorporated by treatment of GMA-grafted polypropylene fibers with excess of diethylene triamine reagent. The conversion of the epoxy groups into the functional groups was investigated as a function of the degree of GMA grafting and reaction time. The ion-exchange characteristics of obtained sorption-active polypropylene fibers were determined. (author)

OLED-polypropylene bio-CD sensor

Science.gov (United States)

Vengasandra, Srikanth; Cai, Yuankun; Grewell, David; Shinar, Joseph; Shinar, Ruth

2008-08-01

With the goal of developing microfluidic platforms for sensing applications, flash-free micro patterns were embossed in polypropylene surfaces with ultrasonic heating for a biosensing lab-on-CD application. The embossed features were designed to act as reservoirs, valves, and reaction chambers to allow, in combination with a compact sensing platform, the monitoring of analyte levels using a standard PC-CD player. To generate the compact sensor, as an example, we chose the photoluminescence (PL)-based detection of lactate and glucose using an OLED-based sensing platform. Once embossed, the surface energy of the plastic substrate was chemically modified to make it hydrophilic. Reagents, placed in separate reservoirs, were directed through burst valves towards a reaction chamber via CD rotation. Lactate or glucose were monitored by measuring the effect of the related dissolved oxygen level on the PL decay time of an oxygen-sensitive dye, following analyte oxidation catalyzed by a suitable specific oxidase enzyme. The results demonstrate the potential of integrating OLEDs as excitation sources in PL-based sensors with microfluidic CD-based platforms, including for simultaneous multiple analyses.

Nanocomposites of polypropylene and organophilic montmorillonite clay: X-ray diffraction, infrared spectroscopy with Fourier transform and water permeation

International Nuclear Information System (INIS)

Morelli, Fernanda C.; Ruvolo Filho, Adhemar

2009-01-01

In this work were prepared nanocomposites of polypropylene and organophilic montmorillonite Cloisite 20A with concentrations of 1.5%, 2.5%, 5.0% and 7.5% clay and graft polypropylene with maleic anhydride as compatibilizer. The mixture was made in the melt state using a twin screw extruder. The materials were characterized by x-ray diffraction, infrared spectroscopy with Fourier transform and analysis of water vapor permeation. The results of x-ray diffraction and infrared spectroscopy indicates the formation of nanocomposites with structures probably exfoliate and / or intercalated for concentrations of 1.5% and 2.5% clay, and provided a marked decrease in the water permeability, corroborating with other analysis. (author)

Physicomechanical evaluation of polypropylene, polyester, and polytetrafluoroethylene meshes for inguinal hernia repair.

Science.gov (United States)

Deeken, Corey R; Abdo, Michael S; Frisella, Margaret M; Matthews, Brent D

2011-01-01

For meshes to be used effectively for hernia repair, it is imperative that engineers and surgeons standardize the terminology and techniques related to physicomechanical evaluation of these materials. The objectives of this study were to propose standard techniques, perform physicomechanical testing, and classify materials commonly used for inguinal hernia repair. Nine meshes were evaluated: 4 polypropylene, 1 polyester, 1 polytetrafluoroethylene, and 3 partially absorbable. Physical properties were determined through image analysis, laser micrometry, and density measurements. Biomechanical properties were determined through suture retention, tear resistance, uniaxial, and ball burst testing with specimens tested in 2 different orientations. A 1-way ANOVA with Tukey's post-test or a t-test were performed, with p INFINIT (WL Gore & Associates) did not resist tearing as effectively as the others. All meshes exhibited supraphysiologic burst strengths except INFINIT and ULTRAPRO. Significant differences exist between the physicomechanical properties of polypropylene, polyester, polytetrafluoroethylene, and partially absorbable mesh prostheses commonly used for inguinal hernia repair. Orientation of the mesh was also shown to be critical for the success of meshes, particularly those demonstrating anisotropy. Copyright © 2011 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

Nuclear magnetic resonance study of the effect of the addition of clay on polypropylene

International Nuclear Information System (INIS)

Nogueira, Regina F.; San Gil, Rosane A.S.; Tavares, Maria Ines B.

2001-01-01

Polypropylene (PP) samples and polypropylene (PP)/clay (M) composite prepared by melting mixing have been characterized by solution and solid state nuclear magnetic resonance spectroscopy (NMR). The monomer sequences distribution and the influence of time and temperature of mechanical mix on the modifications in the PP structure were investigated by 13 C solution NMR. The solid state NMR investigation showed that the 13 C routine spectra such as MAS and CPMAS allowed obtaining information on the molecular domains of chains, and also permits to evaluate the domains mobility. 29 Si and 27 Al solid state NMR were used to characterize the clay and the PP/M composite samples. The results showed that the heating and friction in the range of temperature and time used in the sample preparation did not affect the distribution of configurational sequence in the PP chains. The effect of clay in the PP/M composite structure could be detected, using both 13 C solution and in 29 Si solid state NMR spectra. (author)

Development of more friendly food packaging materials base on polypropylene through blending with polylacticacid

Science.gov (United States)

Setiawan, Achmad Hanafi; Aulia, Fauzan

2017-01-01

The commonly food packaging materials today is used a thin layer plastic or film, which is made of a synthetic polymer, such as polypropylene (PP). However, the use of these polymers has a negative impact on the environment, because the synthetic polymer is difficult to degrade naturally by the biotic components such as micro-organisms decomposers and abiotic components such as the sunshine. The use of the biodegradable polymeric material will reduce the use of synthetic polymer products, thereby reducing plastic waste pollution at relatively low cost, it is expected to produce positive effects both for the environment and in terms of economy. PLA is a biodegradable polymer that can be substituted totally or partially to synthetic polymers as far as could fulfill the main function of packaging in the protection and preservation of food. Increasing PLA content in polypropylene blend will affect to the increasing in its water absorption and also its biodegradable. 20% PLA may the optimum composition of poly-blend for food packaging.

Thermogravimetric studies on alkyl methacrylate polymers and poly(alkyl methacrylate)-grafted polypropylene fibers

International Nuclear Information System (INIS)

Hayakawa, Kiyoshi; Taoda, Hiroshi; Kawase, Kaoru; Tazawa, Masato; Yamakita, Hiromi

1986-01-01

Thermal behavior of several kinds of poly (alkyl methacrylate) and polypropylene-g-poly (alkyl methacrylate) fibers prepared by γ-irradiation was investigated by thermogravimetric measurements with the intermittent analysis of the gaseous products. The degradation of poly (methyl methacrylate) proceeded according to the deploymerization mechanism reproducing the pristine monomer exclusively. The thermogram in inert atmosphere showed the features of a two-step depolymerization, while in air it showed no such a stepwise decrease with the elevating temperature. The dissolution-precipitation treatment of polymer seemed to affect the decomposition behavior. On other alkyl methacrylate polymers, the thermal decomposition generally proceeded also according to the depolymerization mechanism. But, for instance, at least two kinds of products besides its own monomer were formed from poly (isobutyl methacrylate), and their relative fractions differed with the temperature. Polypropylene-g-poly (alkyl methacrylate) fibers showed lowering of initiation temperature of decomposition with the increase in extent of the grafting, and their initiation temperatures of decomposition in air were lower than those in inert atmosphere. (author)

Application of Glass Fiber Waste Polypropylene Aggregate in Lightweight Concrete – thermal properties

Science.gov (United States)

Citek, D.; Rehacek, S.; Pavlik, Z.; Kolisko, J.; Dobias, D.; Pavlikova, M.

2018-03-01

Actual paper focus on thermal properties of a sustainable lightweight concrete incorporating high volume of waste polypropylene aggregate as partial substitution of natural aggregate. In presented experiments a glass fiber reinforced polypropylene (GFPP) which is a by-product of PP tubes production, partially substituted fine natural silica aggregate in 10, 20, 30, 40 and 50 mass %. Results were compared with a reference concrete mix without plastic waste in order to quantify the effect of GFPP use on concrete properties. Main material physical parameters were studied (bulk density, matrix density without air content, and particle size distribution). Especially a thermal transport and storage properties of GFPP were examined in dependence on compaction time. For the developed lightweight concrete, thermal properties were accessed using transient impulse technique, where the measurement was done in dependence on moisture content (from the fully water saturated state to dry state). It was found that the tested lightweight concrete should be prospective construction material possessing improved thermal insulation function and the reuse of waste plastics in concrete composition was beneficial both from the environmental and financial point of view.

Study of modified polypropylene nanocomposites by gamma irradiation with addition of cloisite clay

International Nuclear Information System (INIS)

Komatsu, Luiz G.H.; Oliani, Washington L.; Parra, Duclerc F.; Lugao, Ademar B.

2011-01-01

Nanomaterials, and, in particular, nanoreinforcements for polymer composites have been the subject of intense research, development and commercialization. Clay-containing polymeric nanocomposites (CPNCs) are used as either functional or structural materials, large-volume CPNCs with a commodity or engineering polymer as the matrix, where the mechanical behavior is the main concern (followed by gas-vapor barrier properties, flammability, etc.). This work concerns to the study of the mechanical, thermal and morphological behavior nanocomposite, (HMSPP) Polypropylene High Melt Strength (obtained at dose of 12.5 kGy) and addition of 5 and 10 wt% of organoclay with Cloisite 20A nanocomposite. Agent compatibilizer polypropylene-graft, (PP-g-AM) was added at 3% concentration and the clay was dispersed through melt intercalation technique using a twin-screw extruder). We observed an increase in traction rupture. The mechanical behavior was evaluated by strength, the thermal behavior were evaluated by the technique of differential scanning calorimetry, the morphology of the nanocomposites was studied by scanning electron microscopy, melt flow index and Fourier transformed infrared spectroscopy in nanocomposites Cloisite 20 A at 10% wt. (author)

Polypropylene fumarate/phloroglucinol triglycidyl methacrylate blend for use as partially biodegradable orthopaedic cement.

Science.gov (United States)

Jayabalan, M; Thomas, V; Rajesh, P N

2001-10-01

Polypropylene fumarate/phloroglucinol triglycidyl methacrylate oligomeric blend-based bone cement was studied. Higher the percentage of phloroglucinol triglycidyl methacrylate, lesser the setting time. An optimum setting time could be arrived with 50:50 blend composition of the two oligomers. Composite cement of 50:50 blend prepared with hydroxyapatite granules of particle size 125 microm binds bovine rib bones. The tensile strength of this adhesive bond was found to be 1.11 kPa. The thermal studies suggest the onset of cross-linking reaction in the cured blend if the blend is heated. The absence of softening endotherm in the cured blend shows the thermosetting-like amorphous nature of blend system, which may restrict the changes in creep properties. The in vitro biodegradation studies reveal possible association of calcium ions with negatively charged units of degrading polymer chain resulting in slow down of degradation. Relatively slow degradation was observed in Ringer's solution. The study reveals the potential use of polypropylene fumarate/phloroglucinol triglycidyl methacrylate as partially degradable polymeric cement for orthopaedic applications.

Degradation and biocompatibility of a poly(propylene fumarate)-based/alumoxane nanocomposite for bone tissue engineering.

NARCIS (Netherlands)

Mistry, A.S.; Mikos, A.G.; Jansen, J.A.

2007-01-01

In this work, we evaluated the in vitro cytotoxicity and in vivo biocompatibility of a novel poly(propylene fumarate) (PPF)-based/alumoxane nanocomposite for bone tissue engineering applications. The incorporation of functionalized alumoxane nanoparticles into the PPF-based polymer was previously

Polyfunctional monomers as additives for enhancing the radiation copolymerization of styrene with polyethylene, polypropylene, and PVC

International Nuclear Information System (INIS)

Ang, C.H.; Garnett, J.L.; Levot, R.; Long, M.A.

1982-01-01

Additives which can increase the yield in the radiation grafting of monomers to polymers are useful. The use of polyfunctional monomers as additives (approx. = 1% v/v) are shown to enhance significantly the copolymerization yields of styrene in methanol to films of polyethylene and polypropylene under certain radiation conditions. The results obtained when the polyolefins are replaced by PVC as backbone polymer in these accelerated grafting reactions are reported. Divinylbenzene (DVB) and trimethylolpropane triacrylate (TMPTA) were used as representative polyfunctional monomers for the enhancement effect. When polypropylene was used as backbone polymer, the inclusion of DVB significantly enhanced the radiation grafting of styrene in methanol at all monomer concentrations studied above 35%. At certain monomer concentrations (50% , 60%), the yield of graft copolymer was almost doubled by the addition of DVB. 3 tables. (DP)

Influence of clay type on the performance of Ziegler-Natta catalyst for the synthesis of nanocomposites of PE and PP

International Nuclear Information System (INIS)

Almeida, Lidiane A.; Marques, Maria F.V.; Oliveira, Jaqueline S.

2011-01-01

Polymer nanocomposites present highly improved general properties in comparison with original polymer and their conventional composites. The mayor disadvantage in preparing these materials is the difficulty in the dispersion of the nanofillers in the polymer matrix. In the present work, the synthesis of bisupported (MgCl 2 /clay) catalyst was performed for obtaining polyethylene and polypropylene nanocomposites by in situ polymerization with the aim to achieve higher dispersion of the nanofillers in the polyolefin matrix. Moreover, the influence of ammonium salt (employed in the organophilization of the clay) on the fixation of the catalyst components and therefore, on the catalyst activity was evaluated. The catalysts were characterized by TGA, SEM, EDX, and XRD. Polymers were characterized by DSC, isotactic index through heptane extractables (HS), TGA, EDX, XRD, and optical microscopy (OM). The results showed that the type of clay modifier has a great influence on the catalyst performance. (author)

A novel simultaneous photoelastic and two-beam interferometric system: I. Dynamic full-field evaluation of the elasticity modulus profile of polymeric fibres.

Science.gov (United States)

Hamza, A A; Sokkar, T Z N; El-Farahaty, K A; Raslan, M I

2014-06-01

A novel optical setup for simultaneous capturing of photoelastic and two-beam interference patterns was designed. The designed optical setup was used to simultaneously record two types of patterns. The first pattern is two-beam interference pattern, and the second one is photoelastic interference pattern produced by objects under stress. This simultaneous capturing of the two patterns allowed us to calculate the full-field distribution of the elasticity modulus profile of fibres. A mathematical expression of the profile of the elasticity modulus was derived. This was applied to evaluate the elasticity modulus of anisotropic isotactic polypropylene fibres during stretching processes. The profile of the elasticity modulus was determined for both static and dynamic in situ cases where the propagation of different structural deformations was observed and studied using the designed optical setup. Patterns were given for illustration. © 2014 The Authors Journal of Microscopy © 2014 Royal Microscopical Society.

Histological assessment of titanium and polypropylene fiber mesh implantation with and without fibrin tissue glue.

NARCIS (Netherlands)

Hallers, E.J.O. ten; Jansen, J.A.; Marres, H.A.M.; Rakhorst, G.; Verkerke, G.J.

2007-01-01

Polypropylene (PP) and titanium (Ti) meshes are well-known surgical implants that provoke a relative low foreign body reaction. Firm stabilization of the implant is important to prevent migration and subsequent failure of the operation. Fibrin tissue glues are commercially available adhesives and

Histological assessment of titanium and polypropylene fiber mesh implantation with and without fibrin tissue glue

NARCIS (Netherlands)

ten Hallers, E.J. Olivier; Jansen, John A.; Marres, Henri A.M.; Rakhorst, Gerhard; Verkerke, Gijsbertus Jacob

2007-01-01

Polypropylene (PP) and titanium (Ti) meshes are well-known surgical implants that provoke a relative low foreign body reaction. Firm stabilization of the implant is important to prevent migration and subsequent failure of the operation. Fibrin tissue glues are commercially available adhesives and

Histological assessment of titanium and polypropylene fiber mesh implantation with and without fibrin tissue glue

NARCIS (Netherlands)

ten Hallers, E. J. Olivier; Jansen, John A.; Marres, Henri A. M.; Rakhorst, Gerhard; Verkerke, Gijsbertus J.

Polypropylene (PP) and titanium (Ti) meshes are well-known surgical implants that provoke a relative low foreign body reaction. Firm stabilization of the implant is important to prevent migration and subsequent failure of the operation. Fibrin tissue glues are commercially available adhesives and

Synthesis and Application of a Novel Polyamide Charring Agent for Halogen-Free Flame Retardant Polypropylene

Directory of Open Access Journals (Sweden)

Jie Liu

2013-01-01

Full Text Available A novel charring agent, poly(p-ethylene terephthalamide (PETA, for halogen-free flame retardant polypropylene was synthesized by using p-phthaloyl chloride (TPC and ethylenediamine through solution polycondensation at low temperature, and the effects of PETA on flame retardance of polypropylene (PP/IFR systems were studied. The experimental results showed that PETA could considerably enhance the fire retardant performance as proved by evidence of the increase of limiting oxygen index (LOI values, the results of UL-94 tests, and cone calorimeter tests (CCT. Fourier transform infrared spectroscopy (FTIR and scanning electron microscope (SEM demonstrated that an appropriate amount of PETA could react with PP/IFR system to form cross-link network; a more compact char layer could be formed which was responsible for the improved thermal and flame retardant properties of PP/IFR systems. However, the superfluous amount of PETA would play the negative role.

Influence of the chemical modification and content of the clay on the mechanical properties of polypropylene and national bentonite composites

International Nuclear Information System (INIS)

Libano, Elaine V.D.G.; Pacheco, Elen B.A.V.; Visconte, Leila L.Y.

2011-01-01

The polypropylene/national clay composite was prepared by melt intercalation in a counter-rotating twin screw extruder, using bentonite as filler either in the natural (BENT) form or modified with the ammonium salt, cetyltrimethylammonium chloride (BENT-org). The clay was used in 1, 3 and 5%w. The influence of the modification and content of clay on the mechanical properties of this system was analysed. The analyses of infrared spectroscopy (FTIR) and X-ray diffraction (XRD) showed that clay organophilization did occur. The tensile modulus and the tensile strength at the yield point were not affected by chemical modification (BENT and BENT-org) or clay content. On the other hand, it was evidenced that the elongation at the yield point decreased with the addition of BENT and BENT-org to polypropylene. According to the thermogravimetric results, it was evidenced that the incorporation of clay into polypropylene improved thermal stability of the polymer in the composites with 5%w of BENT and 3 and 5%w of BENT-org. (author)

Polypropylene Nano composites Obtained by In Situ Polymerization Using Metallocenes Catalyst: Influence of the Nanoparticles on the Final Polymer Morphology

International Nuclear Information System (INIS)

Zapata, P.; Quijada, R.

2012-01-01

Polypropylene nano composites containing silica nanospheres based on the sol-gel methods were produced via in situ polymerization using a rac-Et(Ind) 2 ZrCl 2 /methylaluminoxane (MAO) system. Two different routes were used depending on the interaction between the silica nanoparticles with the catalytic system. In route 1 the nanoparticles were added together with the catalytic system (rac-Et(Ind) 2 ZrCl 2 )/(MAO) directly into the reactor, and in route 2 the metallocenes rac-Et(Ind) 2 ZrCl 2 was supported on silica nanospheres pretreated with (MAO). SEM images show that when the nanospheres were added by both routes, they were replicated in the final polymer particle morphology; this phenomenon was more pronounced for PP obtained by route 2. The polypropylene (PP) nano composites obtained by both routes had a slightly higher percent crystallinity and crystallinity temperatures than pure PP. Transmission electron microscopy (TEM) images show that the nanospheres were well dispersed into the polypropylene matrix, particularly in the nano composites obtained by the support system (route 2).

Chapter 1.4: Spatially Resolved Characterization of CNC-Polypropylene composite by Confocal Raman Microscopy

Science.gov (United States)

Umesh Agarwal; Ronald Sabo; Richard Reiner; Craig Clemons; Alan Rudie

2013-01-01

Raman spectroscopy was used to analyze cellulose nanocrystal (CNC)-polypropylene (PP) composites and to investigate the spatial distribution of CNCs in extruded composite filaments. Three composites were made from two forms of nanocellulose (CNCs from wood pulp and the nanoscale fraction of microcrystalline cellulose), and two of the three composites...

Needleless Melt-Electrospinning of Polypropylene Nanofibres

Directory of Open Access Journals (Sweden)

Jian Fang

2012-01-01

Full Text Available Polypropylene (PP nanofibres have been electrospun from molten PP using a needleless melt-electrospinning setup containing a rotary metal disc spinneret. The influence of the disc spinneret (e.g., disc material and diameter, operating parameters (e.g., applied voltage, spinning distance, and a cationic surfactant on the fibre formation and average fibre diameter were examined. It was shown that the metal material used for making the disc spinneret had a significant effect on the fibre formation. Although the applied voltage had little effect on the fibre diameter, the spinning distance affected the fibre diameter considerably, with shorter spinning distance resulting in finer fibres. When a small amount of cationic surfactant (dodecyl trimethyl ammonium bromide was added to the PP melt for melt-electrospinning, the fibre diameter was reduced considerably. The finest fibres produced from this system were 400±290 nm. This novel melt-electrospinning setup may provide a continuous and efficient method to produce PP nanofibres.

Thermal degradation and tensile strength of sansevieria trifasciata-polypropylene composites

Science.gov (United States)

Abral, H.; Kenedy, E.

2015-07-01

The paper exhibits thermal degradation and tensile strength of Sansevieria Trifasciata (ST) fibers and polypropylene (PP) composites. Thermal degradation of ST fibers PP composites was conducted by using thermogravimetry (TGA) instrument, meanwhile tensile strength of the composite was done by using tensile equipment. The results show that the thermal resistance of ST fibers PP composites was higher than that of virgin PP only. Increases in volume fraction of fibers in the composites enhance the tensile strength. Scanning Electron Microscope (SEM) observation exhibits good interface bonding between ST fibers and PP matrix.

Thermal degradation and tensile strength of sansevieria trifasciata-polypropylene composites

International Nuclear Information System (INIS)

Abral, H; Kenedy, E

2015-01-01

The paper exhibits thermal degradation and tensile strength of Sansevieria Trifasciata (ST) fibers and polypropylene (PP) composites. Thermal degradation of ST fibers PP composites was conducted by using thermogravimetry (TGA) instrument, meanwhile tensile strength of the composite was done by using tensile equipment. The results show that the thermal resistance of ST fibers PP composites was higher than that of virgin PP only. Increases in volume fraction of fibers in the composites enhance the tensile strength. Scanning Electron Microscope (SEM) observation exhibits good interface bonding between ST fibers and PP matrix. (paper)

Jute fiber reinforced polypropylene produced by continuous extrusion compounding. Part 1. Processing and ageing properties

NARCIS (Netherlands)

Oever, van den M.J.A.; Snijder, M.H.B.

2008-01-01

This article addresses the processing and ageing properties of jute fiber reinforced polypropylene (PP) composites. The composite has been manufactured by a continuous extrusion process and results in free flowing composite granules, comprising up to 50 weight percent (wt %) jute fiber in PP. These

Using Raman spectroscopic imaging for non-destructive analysis of filler distribution in chalk filled polypropylene

DEFF Research Database (Denmark)

Boros, Evelin; Porse, Peter Bak; Nielsen, Inga

2016-01-01

A feasibility study on using Raman spectral imaging for visualization and analysis of filler distribution in chalk filled poly-propylene samples has been carried out. The spectral images were acquired using a Raman spectrometer with 785 nm light source.Eight injection-molded samples with concentr...

Evaluating penetration ability of Plodia interpunctella (Hübner) (Lepidoptera: Pyralidae) larvae into multilayer polypropylene packages

Science.gov (United States)

Larvae of the Indian meal moth, Plodia interpunctella (Hübner), can invade or penetrate packaging materials and infest food products. Energy bars with three polypropylene packaging types were challenged with eggs (first instars), third, and fifth instars of P. interpunctella to determine package res...

Influence of low shear mixing settings on the mechanical properties of long glass fibre polypropylene

NARCIS (Netherlands)

de Bruijn, Thomas A.; Vincent, Guillaume Almire; van Hattum, Ferrie

2017-01-01

The influence of several mixing settings on the mechanical properties were studied. A Long fibre thermoplastic glass polypropylene material was mixed, compression moulded and analysed by flexural tests and charpy impact. In a low-shear mixing machine, chosen for limited fibre length degradation, six

Peritoneostomy with latex coated polypropylene: experimental study in rats Peritoniostomia com polipropileno revestido por látex: estudo experimental em ratos

Directory of Open Access Journals (Sweden)

Renato Hugues Atique Claudio

2006-12-01

Full Text Available PURPOSE: To evaluate if latex coated polypropylene mesh leads to less adhesions formation. METHODS: 90 rats were distributed in three groups. Group I (control was submitted to median laparotomy and posterior synthesis; Group II (polypropylene was submitted to a segment resection of the abdominal wall, and the defect was corrected with a polypropylene mesh; Group III using the new material (latex coated polypropylene. After 45 days the euthanasia procedure was done and the adhesions were evaluated in 2 ways: 1 classification in a grading system; 2 evaluation of the adhesion area, which was calculated by resection of the adhesions after dying with Indian blue ink. RESULTS: The classification in a grading system showed that Group III animals had less adhesions formation (P0.05. The severe complications (fistula, evisceration and obstruction, which were lethal, were not reduced by the latex coated material. CONCLUSION: Latex coated polypropylene causes fewer adhesion formations than polypropylene alone, although it does not diminish the severe early complications.OBJETIVO: Avaliar se o revestimento da tela de polipropileno com látex leva a menor formação de aderências. MÉTODOS: Foram utilizados 90 ratos, distribuídos em três grupos de 30: grupo I (controle animais submetidos a laparotomia mediana e posterior síntese; grupo II (polipropileno ressecção de segmento da parede abdominal e síntese com tela de polipropileno; grupo III, (polipropileno revestido por látex. Eutanásia foi realizada após 45 dias e as aderências avaliadas sob duas formas: 1 classificação em graus; 2 avaliação da área aderida, calculada corando-se o segmento da parede contendo as aderências que posteriormente foram ressecadas produzindo uma região clara em contraste com o restante da peça, corada. RESULTADOS: Na avaliação por meio de graus, o grupo III apresentou menor formação de aderências (p0,05. As complicações graves não foram reduzidas pelo

Electron beam processing of rubber wood fibers - polypropylene composites. Effects of reactive additives on the physical and mechanical properties

International Nuclear Information System (INIS)

Nor Yuziah Mohd Yunus; Jalaluddin Harun; Khairul Zaman

2000-01-01

The purpose of this study is to determine the suitability of producing agro-fiber reinforced plastic composite (agro-FRPC) from rubber wood fiber blended in polypropylene matrix. The effects of varying fiber dimension and fiber content on the physical and mechanical properties of the composite were evaluated to provide an insight into the fiber matrix adhesion. The effects of reactive additives on the physical and mechanical properties of the composite were evaluated which provides the insight on the reinforcement of the composite. Rubber wood fiber used in this study is currently being used in the manufacturing of medium density fiber (MDF) board. Two sizes of rubber wood fiber were used i.e. 0.5-1.0 mm and 1.0-2.0 mm. Homopolymer polypropylene of MFI 14.0 was used as a matrix. The irradiation work was carried out using electron beam accelerator, 3.0 MeV, 3.0 mA. Various types of reactive additives (RA) with mono-functional, di-functional, tri-functional and oligomer were applied in the blend. For comparison, a conventional chemical cross-linking using two types of maleated polypropylene, MPA (Mw=9,000) and PMAP (Mw=220,000) were also performed. (author)

Electron beam processing of rubber wood fibers - polypropylene composites. Effects of reactive additives on the physical and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Nor Yuziah Mohd Yunus; Jalaluddin Harun [Universiti Putra Malaysia, Selangor Darul Ehsan (Malaysia); Khairul Zaman [Malaysian Institute for Nuclear Technology Research (MINT), Selangor Darul Ehsan (Malaysia)

2000-07-01

The purpose of this study is to determine the suitability of producing agro-fiber reinforced plastic composite (agro-FRPC) from rubber wood fiber blended in polypropylene matrix. The effects of varying fiber dimension and fiber content on the physical and mechanical properties of the composite were evaluated to provide an insight into the fiber matrix adhesion. The effects of reactive additives on the physical and mechanical properties of the composite were evaluated which provides the insight on the reinforcement of the composite. Rubber wood fiber used in this study is currently being used in the manufacturing of medium density fiber (MDF) board. Two sizes of rubber wood fiber were used i.e. 0.5-1.0 mm and 1.0-2.0 mm. Homopolymer polypropylene of MFI 14.0 was used as a matrix. The irradiation work was carried out using electron beam accelerator, 3.0 MeV, 3.0 mA. Various types of reactive additives (RA) with mono-functional, di-functional, tri-functional and oligomer were applied in the blend. For comparison, a conventional chemical cross-linking using two types of maleated polypropylene, MPA (Mw=9,000) and PMAP (Mw=220,000) were also performed. (author)

Surface modification of polypropylene mesh devices with cyclodextrin via cold plasma for hernia repair: Characterization and antibacterial properties

Science.gov (United States)

Sanbhal, Noor; Mao, Ying; Sun, Gang; Xu, Rui Fang; Zhang, Qian; Wang, Lu

2018-05-01

Light weight polypropylene (PP) mesh is the most widely used implant among all other synthetic meshes for hernia repair. However, infection is the complication associated to all synthetic meshes after hernia repair. Thus, to manage mesh related infection; antibacterial drug is generally loaded to surgical implants to supply drug locally in mesh implanted site. Nevertheless, PP mesh restricts the loading of antibacterial drug at operated area due to its low wettability. The aim of this study was to introduce a novel antimicrobial PP mesh modified with β-cyclodextrine (CD) and loaded with antimicrobial agent for infection prevention. A cold oxygen plasma treatment was able to activate the surfaces of polypropylene fibers, and then CD was incorporated onto the surfaces of PP fibers. Afterward, triclosan, as a model antibacterial agent, was loaded into CD cavity to provide desired antibacterial functions. The modified polypropylene mesh samples CD-Tric-1, CD-Tric-3 exhibited excellent inhibition zone and continuous antibacterial efficacy against E. coli and S. aureus up to 6 and 7 days respectively. Results of AFM, SEM, FTIR and antibacterial tests evidenced that oxygen plasma process is necessary to increase chemical connection between CD molecules and PP fibers. The samples were also characterized by using EDX, XRD, TGA, DSC and water contact angle.

End-group characterisation of poly(propylene glycol)s by means of electrospray ionisation-tandem mass spectrometry (ESI-MS/MS).

Science.gov (United States)

Jackson, Anthony T; Slade, Susan E; Thalassinos, Konstantinos; Scrivens, James H

2008-10-01

The end-group functionalisation of a series of poly(propylene glycol)s has been characterised by means of electrospray ionisation-tandem mass spectrometry (ESI-MS/MS). A series of peaks with mass-to-charge ratios that are close to that of the precursor ion were used to generate information on the end-group functionalities of the poly(propylene glycol)s. Fragment ions resulting from losses of both of the end groups were noted from some of the samples. An example is presented of how software can be used to significantly reduce the length of time involved in data interpretation (which is typically the most time-consuming part of the analysis).

Thermal Stability of Clay's Galleries in Polypropylene - Clay (montmorillonite Nanocomposites using Polypropylene-gMaleic Anhydride as Compatibilizer

Directory of Open Access Journals (Sweden)

Sotya Astutiningsih

2010-10-01

Full Text Available Superior properties of food packaging can be achieved using nanocomposite technology. However, fabrication of this materials are complex and expensive. Long term objectives of this research is the synthesis of low cost polypropylene clay nanocomposites (PPCN via a short-cut method known as ‘cascade engineering’. Cascade engineering principle in PPCN fabrication is performed by using compatibilizer (to enable the mixing of PP and clay masterbatch, and PPCN in one pot process using melt mixer. This paper present the experimental results using small-angle x-ray diffraction (XRD on the thermal stability of the PPCN. Results from the XRD analysis showed that the clay was intercalated, however no significant changes were observed as a result of variation in mixing time. XRD patterns of the annealed PPCN showed reduction of MMT’s gallery (deintercalation These phenomenon was probably caused by insufficient bonding and lack of compatibility between PP-g-MA and MMT.

Studies on improvement of mechanical properties of Kenaf-reinforced polypropylene composites

International Nuclear Information System (INIS)

Sarifah Hanisah Syed Abd Aziz; Khairul Zaman Mohd Dahlan

2006-01-01

At present, research in composite materials is being directed at using natural fibres instead of synthetic fibres. Kenaf which is extensively grown in the Far East including Malaysia, has been identified as a bast (stem) fibre with significant market potential. In this work, long and random kenaf fibres were used in the as-received condition and alkalized with a 0.06 M NaOH solution. They were combined with polypropylene thin sheets, sandwiched between layers of kenaf fibres and hot-pressed to form natural fibre composites. The mechanical properties of the composites were investigated to observe the effect of fibre alignment, fibre treatment, the addition of coupling agent and pre-irradiation method used. A general trend was observed whereby alkalized and long fibre composites gave higher flexural modulus and flexural strength compared with random mat and untreated fibres. The long fibre composites also gave a higher work of fracture. However, the correlation between fibre surface treatment and the work of fracture was less clear. The addition of coupling agent at 1% showed a slight improvement on the mechanical performance of the composites whereas pre-irradiation on the polypropylene pellets and fibres before the composite is manufactured showed significant improvement on the mechanical properties. However, the method of moulding used need to be improved to optimize the performance of the composites. (Author)

Formation of CuxS Layers on Polypropylene Sulfurized by Molten Sulfur

Directory of Open Access Journals (Sweden)

Rasa ALABURDAITĖ

2011-11-01

Full Text Available The processes of formation of electrically conductive layers of copper sulfides CuxS by the sorption-diffusion method on polypropylene (PP using molten sulfur as sulfurizing agent was investigated. The amount of sorbed sulfur increased with the increase of the duration of treatment. Copper sulfide layers were formed on the surface of polypropylene after the treatment of sulfurized polymer with Cu(II/I salt solution. The amount of copper sulfide in layer increased with the increase of treatment duration in copper salt solution. XRD spectra of PP films treated for 3 min with molten sulfur and then with Cu(II/I salt solution for the different time showed that the copper sulfide phases, mostly digenite, Cu2-xS and a-chalcocite, Cu2S were formed in the layers. Electromotive force measurement results confirmed the composition of formed CuxS layers on PP. The phase composition of layers also changed after the annealing. The value of electrical resistance of copper sulfide layers on PP varied from 20 W/cm2 to 80 W/cm2 and after annealing at 80 °C - in the interval of 10 W/cm2 - 60 W/cm2.http://dx.doi.org/10.5755/j01.ms.17.4.776

Influence of radiational oxidation on the kinetics of electrization of polypropylene by electron irradiation

International Nuclear Information System (INIS)

Rozno, A.G.; Romanov, A.V.; Sukhov, N.L.; Gromov, V.V.; Ershov, B.G.

1992-01-01

Kinetics of volumetric electric charge and accumulation of paramagnetic centres (PMC) in polypropylene (PP) of two crystal modifications, subjected to radiational oxidation were studied. A correlation between volumetric charge and PMC in radiationally oxidation PP was detected. Considerable influence of crystal phase on the processes of charging and radiational oxidation was revealed

Synthesis of Isotactic-block-Syndiotactic Poly(methyl Methacrylate via Stereospecific Living Anionic Polymerizations in Combination with Metal-Halogen Exchange, Halogenation, and Click Reactions

Directory of Open Access Journals (Sweden)

Naoya Usuki

2017-12-01

Full Text Available Isotactic (it- and syndiotactic (st- poly(methyl methacrylates (PMMAs form unique crystalline stereocomplexes, which are attractive from both fundamental and application viewpoints. This study is directed at the efficient synthesis of it- and st-stereoblock (it-b-st- PMMAs via stereospecific living anionic polymerizations in combination with metal-halogen exchange, halogenation, and click reactions. The azide-capped it-PMMA was prepared by living anionic polymerization of MMA, which was initiated with t-BuMgBr in toluene at –78 °C, and was followed by termination using CCl4 as the halogenating agent in the presence of a strong Lewis base and subsequent azidation with NaN3. The alkyne-capped st-PMMA was obtained by living anionic polymerization of MMA, which was initiated via an in situ metal-halogen exchange reaction between 1,1-diphenylhexyl lithium and an α-bromoester bearing a pendent silyl-protected alkyne group. Finally, copper-catalyzed alkyne-azide cycloaddition (CuAAC between these complimentary pairs of polymers resulted in a high yield of it-b-st-PMMAs, with controlled molecular weights and narrow molecular weight distributions. The stereocomplexation was evaluated in CH3CN and was affected by the block lengths and ratios.

Tough and Reinforced Polypropylene/Kaolin Composites using Modified Kaolin

Science.gov (United States)

Yao, J. L.; Zhu, H. X.; Qi, Y. B.; Guo, M. J.; Hu, Q.; Gao, L.

2018-05-01

Polypropylene (PP)/kaolin composites have been prepared by filling modified kaolin with diethylenetriaminepentaacetic acid (DTPA) into the PP matrix. The surface modification of kaolin particles effectively improves the compatibility between kaolin and PP matrix. It is conducive for uniform dispersion of inorganic particles in the matrix, and enhances the mechanical performance of the composites. Compared with plain kaolin, the mechanical properties of the modified composites exhibit higher tensile strength, bending strength, impact strength and melt index simultaneously. The DTPA modification of kaolin overall enhances the mechanical properties of PP composites. It meets the requirements in various applications, and makes the modified experiment interesting in modern teaching.

Development of polypropylene (PP)/bentonite organoclay nanocomposites; Desenvolvimento de nanocompositos de polipropileno/argila bentonitica organofilica

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Carlos Ivan Ribeiro de; Rocha, Marisa Cristina Guimaraes; Verly, Jessica, E-mail: carlosivanr@gmail.com [Universidade do Estado do Rio de Janeiro (UERJ), Nova Friburgo, RJ (Brazil). Instituto Politecnico; Silva, Ana Lucia Nazareth da [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Instituto de Macromoleculas Professora Eloisa Mano; Bertolino, Luiz Carlos [Centro de Tecnologia Mineral (CETEM), Rio de Janeiro, RJ (Brazil)

2016-07-01

In recent years, a significant number of studies on polymer/clay nanocomposites has been developed due to the improved properties these materials have compared to those of the conventional composites. Among the various clays used for preparing nanocomposites, the bentonite clays have been the most widely used. In this context, the aim of this work is to develop polypropylene/organoclay nanocomposites based on deposits of bentonite clays recently discovered in Cubati, PB. The composites were prepared in a twin screw extruder. The structural characterization of the produced materials indicated a possible intercalation of the polymer chains between the layers of the organoclay. The results of impact strength showed that the addition of clay as well as the initial addition of clay and compatibilizer decreased the impact strength of polypropylene. The Young's modulus and tensile strength of the polymer were not significantly affected by the filler addition. However, an increase of the elongation at break was observed. (author)

Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

Directory of Open Access Journals (Sweden)

Arun Kumar Gupta

2012-01-01

Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

Poly(propylene carbonate): Insight into the Microstructure and Enantioselective Ring-Opening Mechanism

KAUST Repository

Salmeia, Khalifah A.

2012-11-13

Different poly(propylene carbonate) (PPC) microstructures have been synthesized from the alternating copolymerization of CO 2 with both racemic propylene oxide (PO) and various mixtures of PO enantiomers using chiral salen catalysts. The microstructures of the obtained copolymers as a function of polymerization time have been analyzed by a combination of chiral GC and high-resolution NMR spectroscopy. The 13C NMR spectra of selected poly(propylene carbonate) samples were recorded using a 900 MHz ( 1H) spectrometer, showing a previously unreported fine splitting of the carbonate resonances. This allowed a detailed assignment of signals for various copolymer microstructures taking into account the specifics in their stereo- and regioirregularities. For example, the enantioselectivity preference of the (R,R-salen)Co catalyst for (S)-PO at the beginning of the copolymerization leads predominantly to (S)-PO insertion, with any (R)-PO misinsertion being followed by incorporation of (S)-PO, so that the microstructure features isolated stereoerrors. K rel calculations for the copolymerization showed around 5-fold enantioselectivity for (S)-PO over (R)-PO at short reaction time. Analysis of the copolymer microstructures obtained under various reaction conditions appears to be an additional approach to differentiate the occurrence of bimetallic and bifunctional copolymerization mechanisms that are widely discussed in the literature. © 2012 American Chemical Society.

Poly(propylene carbonate): Insight into the Microstructure and Enantioselective Ring-Opening Mechanism

KAUST Repository

Salmeia, Khalifah A.; Vagin, Sergei; Anderson, Carly E.; Rieger, Bernhard

2012-01-01

Different poly(propylene carbonate) (PPC) microstructures have been synthesized from the alternating copolymerization of CO 2 with both racemic propylene oxide (PO) and various mixtures of PO enantiomers using chiral salen catalysts. The microstructures of the obtained copolymers as a function of polymerization time have been analyzed by a combination of chiral GC and high-resolution NMR spectroscopy. The 13C NMR spectra of selected poly(propylene carbonate) samples were recorded using a 900 MHz ( 1H) spectrometer, showing a previously unreported fine splitting of the carbonate resonances. This allowed a detailed assignment of signals for various copolymer microstructures taking into account the specifics in their stereo- and regioirregularities. For example, the enantioselectivity preference of the (R,R-salen)Co catalyst for (S)-PO at the beginning of the copolymerization leads predominantly to (S)-PO insertion, with any (R)-PO misinsertion being followed by incorporation of (S)-PO, so that the microstructure features isolated stereoerrors. K rel calculations for the copolymerization showed around 5-fold enantioselectivity for (S)-PO over (R)-PO at short reaction time. Analysis of the copolymer microstructures obtained under various reaction conditions appears to be an additional approach to differentiate the occurrence of bimetallic and bifunctional copolymerization mechanisms that are widely discussed in the literature. © 2012 American Chemical Society.

Comparative study between polypropylene and polypropylene/poliglecaprone meshes used in the correction of abdominal wall defect in rats Estudo comparativo entre as telas de polipropileno e polipropileno/poliglecaprone utilizadas na correção de defeito na parede abdominal ventral de ratos

Directory of Open Access Journals (Sweden)

Carlos Alberto Lima Utrabo

2012-04-01

Full Text Available PURPOSE: To evaluate the healing process of a defect in the ventral abdominal wall of rats, comparing the polypropylene and polypropylene/poliglecaprone meshes on the 30th and 60th postoperative day. METHODS: Thirty two Wistar rats were submitted to a ventral abdominal wall defect, with integrity of the parietal peritoneum. In the repair, were used polypropylene (group A and polypropylene/poliglecaprone (group B meshes. The groups were subdivided into four subgroups of eight animals euthanized on the 30th (A30 and B30 and 60th postoperative day (A60 and B60. Fragments of the abdominal wall of the animals were submitted to macroscopic, tensiometric and histological evaluations. RESULTS: The tensiometry on subgroup A30 showed a mean average break point of 0.78 MPa and in A60, 0.66 Mpa. In subgroup B30 it was 0.84 MPa and in B60, 1.27 Mpa. The score of the inflammatory process showed subacute phase on A30 and B30 sub-groups and chronic inflammatory process in subgroups A30 and 60B. CONCLUSIONS: The tensile strength was higher on the wall repaired by polypropylene/poliglecaprone mesh in the 60th post-operative day. Histology showed higher concentration of fibrosis on the surface of the polypropylene mesh with a tendency to encapsulation. In polypropylene/poliglecaprone subgroups the histology showed higher concentration of fibrosis on the surface of mesh filaments.OBJETIVO: Avaliar a cicatrização de um defeito, na parede abdominal ventral de ratos, comparando-se as telas de polipropileno e polipropileno/poliglecaprone no 30º e 60º dia do pós-operatório. MÉTODOS: Trinta e dois ratos Wistar foram submetidos à produção de defeito na parede abdominal ventral, com integridade do peritônio parietal. Na correção foram utilizadas as telas de polipropileno (grupo A e polipropileno/poliglecaprone (grupo B. Houve subdivisão em quatro subgrupos (A30, A60, B30 e B60 de oito animais que foram submetidos à eutanásia no 30º e 60º dia do p

The influence of temperature on the formation of liquid fuel from Polypropylene plastic wastes

Science.gov (United States)

Martynis, M.; Mulyazmi; Praputri, E.; Witri, R.; Putri, N.

2018-03-01

The current trend of municipal waste management in urban areas is caused by rapid changes in social, economic, political and cultural life. As a non-biodegradable polymers that have become essential materials, plastic wastes have created a very serious environmental challenge because of the huge quantities and their disposal problems. Recycling of plastics is seen as one method for reducing environmental and resource depletion. The most attractive technique of plastics recycling is pyrolysis involving the degradation of the polymeric materials by heating in the absence of oxygen. This study investigated the characteristics of pyrolysis liquid fuel (PLF) produced from polypropylene plastic wastes with temperature variations. Pyrolisis was carried out on 200 grams of polypropylene waste plastics at the operating temperature of 200°C, 250°C, 300 °C and 350 °C for 45 minutes. The liquid products were found to have carbon chain length in the range of C8-C9, similar with gasoline. The maximum density, volume and calorific value of the oil obtained were 0.8 g/cm3, 61 ml and 1307 cal/gr, respectively.

Super Oxygen and Improved Water Vapor Barrier of Polypropylene Film with Polyelectrolyte Multilayer Nanocoatings.

Science.gov (United States)

Song, Yixuan; Tzeng, Ping; Grunlan, Jaime C

2016-06-01

Biaxially oriented polypropylene (BOPP) is widely used in packaging. Although its orientation increases mechanical strength and clarity, BOPP suffers from a high oxygen transmission rate (OTR). Multilayer thin films are deposited from water using layer-by-layer (LbL) assembly. Polyethylenimine (PEI) is combined with either poly(acrylic acid) (PAA) or vermiculite (VMT) clay to impart high oxygen barrier. A 30-bilayer PEI/VMT nanocoating (226 nm thick) improves the OTR of 17.8 μm thick BOPP by more than 30X, rivaling most inorganic coatings. PEI/PAA multilayers achieve comparable barrier with only 12 bilayers due to greater thickness, but these films exhibit increased oxygen permeability at high humidity. The PEI/VMT coatings actually exhibit improved oxygen barrier at high humidity (and also improve moisture barrier by more than 40%). This high barrier BOPP meets the criteria for sensitive food and some electronics packaging applications. Additionally, this water-based coating technology is cost effective and provides an opportunity to produce high barrier polypropylene film on an industrial scale. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tension free monofilament macropore polypropylene mesh (Gynemesh PS in female genital prolapse repair

Directory of Open Access Journals (Sweden)

Vicente Sola

2006-08-01

Full Text Available OBJECTIVES: To review intraoperative and postoperative complications associated to the correction of cystocele and rectocele with polypropylene mesh macropore monofilament (Gynemesh PS using transvaginal free tension technique. MATERIALS AND METHODS: Prospective study of patients that have been submitted to correction of cystocele and/or rectocele between November 2004 and August 2005 in the Urogynecology and Vaginal Surgery Unit of Gynecology and Obstetrics Department, Las Condes Clinic. Mesh was used in 31 patients: 9 for cystocele, 11 for rectocele, and 11 for concomitant meshes. Total mesh used 42. Media age 55 years old, weight 64 kilograms. In 7 patients we used a third mesh for correction of urinary incontinence by TVT-O technique. RESULTS: They did not present intraoperative complications, neither in immediate or delayed postoperative time. We did not observe hematoma, infection, erosion or exposition mesh. Healing of cystocele and rectocele was obtained in 100% of patients, with a pursuit between 1 and 8 months. DISCUSSION: The use of prosthetic polypropylene monofilament macropore mesh in the correction of cystocele and/or rectocele, by transvaginal route with tension free technique seems to be a safe and effective surgery procedure.

The preparation of layered double hydroxide wrapped carbon nanotubes and their application as a flame retardant for polypropylene

International Nuclear Information System (INIS)

Du Baoxian; Fang Zhengping

2010-01-01

Carbon nanotubes (CNTs) wrapped with layered double hydroxide (LDH-w-CNTs) were facilely obtained through in situ introduction of CNTs into the hydrothermal reaction system of LDH, with the goal of combining their unique physical and chemical characteristics to meet new advanced applications. Morphological observations indicated that LDH lamellae enwrapped the surface of CNTs and the wrapping degree was dependent on the functionalization of CNTs. ζ-potential measurements showed that the interaction between the positive charge of LDH and the negative charge of CNTs was the main driving force of the wrapping process. Both hybrids led to a reduction in the peak heat release rate (PHRR) of polypropylene, indicating that they could confer better flame retardancy on polypropylene with respect to LDH and CNTs.

Morphological Development of Melt Crystallized Poly(propylene oxide) by In Situ AFM: Formation of Banded Spherulites

NARCIS (Netherlands)

Beekmans, L.G.M.; Hempenius, Mark A.; Vancso, Gyula J.

2004-01-01

The morphology of poly(propylene oxide) (PPO) crystals grown from the melt was investigated. The spherulites of the optically pure S polymers displayed a regular pattern of concentric rings as observed by polarizing optical microscopy, while the stereocopolymer developed irregularly banded, or

Enhancement of mechanical properties and interfacial adhesion by chemical odification of natural fibre reinforced polypropylene composites

CSIR Research Space (South Africa)

Erasmus, E

2008-11-01

Full Text Available with the polymer matrix. Therefore, the constituents need to be chemically modified to enhancing adhesion between fibre and polymer matrix. The aim of this work is to improve the interfacial adhesion between the polypropylene matrix and the natural fibre...

Nanocomposites of polypropylene and organophilic clay: X ray diffraction, absorption infrared spectroscopy with fourier transform and water vapor permeation

International Nuclear Information System (INIS)

Morelli, Fernanda C.; Ruvolo Filho, Adhemar

2010-01-01

In this work nano composites were prepared from polypropylene, graft polypropylene with maleic anhydride as compatibilizer and organophilic montmorillonite Cloisite 20A with concentrations of 1.5, 2.5, 5.0 and 7.5% clay. The mixture was made in the melt state using a twin screw extruder. The materials were characterized by X ray diffraction, infrared spectroscopy with Fourier transform and analysis of water vapor permeation. The results of X ray diffraction and absorption infrared spectroscopy indicates the formation of nano composites with structures probably exfoliate and or intercalated for concentrations of 1.5 and 2.5% clay, and provided a marked decrease in the water permeability, corroborating with other analyses. (author)

Functionalisation of polypropylene non-woven fabrics (NWFs): Functionalisation by oxyfluorination as a first step for graft polymerisation

CSIR Research Space (South Africa)

Vargha, V

2011-10-01

Full Text Available Surface oxyfluorination had been carried out on polypropylene non-woven fabric (PP NWF) samples of different morphologies and pore sizes. The modified surfaces were characterised by Attenuated Total Reflectance Fourier Transform InfraRed (ATR...

Micromechanical Characterization of Complex Polypropylene Morphologies by HarmoniX AFM

Directory of Open Access Journals (Sweden)

S. Liparoti

2017-01-01

Full Text Available This paper examines the capability of the HarmoniX Atomic Force Microscopy (AFM technique to draw accurate and reliable micromechanical characterization of complex polymer morphologies generally found in conventional thermoplastic polymers. To that purpose, injection molded polypropylene samples, containing representative morphologies, have been characterized by HarmoniX AFM. Mapping and distributions of mechanical properties of the samples surface are determined and analyzed. Effects of sample preparation and test conditions are also analyzed. Finally, the AFM determination of surface elastic moduli has been compared with that obtained by indentation tests, finding good agreement among the results.