Encapsulation of krypton-85 in zeolite molecular sieve with a hot isostatic press

International Nuclear Information System (INIS)

Christensen, A.B.; DelDebbio, J.A.; Knecht, D.A.; Tanner, J.E.

1986-01-01

This paper describes pilot and full-scale experiments which demonstrated the feasibility of immobilizing Kr-85 in a zeolite 5A/glass mixture and compacting it before disposal. The full volume of a one-liter hot isostatic press (HIP) was used to trap argon in zeolite 5A. For radioactive krypton the HIP was modified to isolate the Kr-85 in the work zone. Details of the HIP modifications, experimental procedure, and sample analysis are reported

Characterization of hot isostatically pressed Bi-Sr-Ca-Cu-O as a function of consolidation variables

International Nuclear Information System (INIS)

Goretta, K.C.; Miller, D.J.; Poeppel, R.B.; Nash, A.S.

1992-01-01

This paper reports that fully dense, bulk Bi 2 Sr 1.7 CaCu 2 O x superconductor pellets were made by hot isostatic pressing in an inert atmosphere. Electron microscopy revealed that rotation and bending of the platelike 2212 grains were responsible for much of the densification. Under processing conditions of 825 degrees C and 105 MPa, dense pellets were obtained in 15 min. Many dislocations, planar faults, and, perhaps, intergrowths of the Bi 2 Cr 2 CuO x phase were produced during pressing. The dislocations were largely present in subgrain boundaries when the pressing times were increased to 45-120 min

Processing of surrogate nuclear fuel pellets for better dimensional control with dry bag isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Hoggan, Rita E., E-mail: Rita.hoggan@inl.gov; Zuck, Larry D., E-mail: Larry.zuck@inl.gov; Cannon, W. Roger, E-mail: cannon@rutgers.edu; Lessing, Paul A., E-mail: p.a.l.2@hotmail.com

2016-12-15

A study of improved methods of processing fuel pellets was undertaken using ceria and zirconia/yttria/alumina as surrogates. Through proper granulation, elimination of fines and vertical vibration (tapping) of the parts bag prior to dry bag isostatic pressing (DBIP), reproducibility of diameter profiles among multiple pellets of ceria was improved by almost an order of magnitude. Reproducibility of sintered pellets in these studies was sufficient to allow pellets to be introduced into the cladding with a gap between the pellet and cladding on the order of 50 μm to 100 μm but not a uniform gap with tolerance of ±12 μm as is currently required. Deviation from the mean diameter along the length of multiple pellets, and deviation from roundness, decreased after sintering. This is not generally observed with dry pressed pellets. Sintered shrinkage was uniform to ±0.05% and thus, as an alternative, pellets may be machined to tolerance before sintering, thus avoiding the waste associated with post-sinter grinding. - Highlights: • Three methods of granule preparation for two different powder sources were outlined and compared using tap density curves. • A dry bag isostatic press was used to fabricate pellets and longer rods. Thus longer pellets could be fabricated by this technique. • Vertical vibrations to pack granules decreased variation in dimensions from pellet to pellet by a factor of nine. • Sintering shrinkage varied by only 0.1% along the length of a rod. Thus green machining prior to sintering could result in tight tolerances.

Development of oxide dispersion strengthened W alloys produced by hot isostatic pressing

International Nuclear Information System (INIS)

Martinez, J.; Savoini, B.; Monge, M.A.; Munoz, A.; Pareja, R.

2011-01-01

A powder metallurgy technique has been developed to produce oxide strengthened W-Ti and W-V alloys using elemental powders and nanosized powders of La 2 O 3 or Y 2 O 3 as starting materials. The alloys consolidated by hot isostatic pressing resulted in high-density materials having an ultrafine-grained structure and microhardness values in the range 7-13 GPa. Atom force microscopy studies show a topographic relief in the Ti and V pools that appear in the consolidated alloys. This relief is attributed to the heterogeneous nucleation of martensite plates. The preliminary transmission electron microscopy studies have revealed that a dispersion of nanoparticles can be induced in these alloys produced via the present technique.

Interface analysis of A1 matrix composites produced by hot isostatic pressing, squeeze casting and semi-solid processing

International Nuclear Information System (INIS)

Shamsul, J.B.; Zainal Arifin Ahmad; Faaizulaswad, M.S.; Azmi, R.

2000-01-01

The interface analysis has been carried out an aluminium based composites system produced by hot isostatic pressing, squeeze casting and semi-solid processing. A range of different fabrication techniques has been used to produce different types of microstructure of Al 2124 (Al-Cu-Mg) reinforced with 5 weight % SiC particles. Blending followed by hot isostatic pressing is used to fabricate composite I. Composite II was 6061 (Al-Si-Mg) wrought aluminium alloy reinforced with fibres of alumina-silica (V f = 0.58) and fabricated by squeeze casting. Finally, A356 (AlSi7Mg0.3) alloy was reinforced with 20 Vol.% of SiC particles (13 μm) and namely as composite III. Composite III is fabricated by semi-solid processing. Interface analysis was done by optical microscopy, scanning and transmission electron microscopy. Composite I exhibited good interface bonding and dislocation was also observed near the interface. Elements such as Al, Fe, Cr, Mn were found near the interface of composite II and intermetallic of iron rich inclusion and Mg 2 Si were observed near the interface of composite III. (Author)

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

OpenAIRE

Cooper, Adam J.; Sherry, Andrew

2018-01-01

Herein, we have performed J-Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP’d) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (− 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J0.2BL, when compared to equivalently graded forged 304L, which is relatively constant...

Densification of boron carbide at relatively low temperatures by hot pressing and hot isostatic pressing

International Nuclear Information System (INIS)

Telle, R.

1988-01-01

The poor sinterability of B 4 C limits its widespread application because both high temperatures and high pressures are required for a complete densification. Moreover, B 4 C suffers from a low strength and fracture toughness, possesses, however, a high potential because of its extreme hardness. Reaction hot pressing of B 4 C-WC-TiC-Si-Co mixtures resulting in B 4 C-TiB 2 -W 2 B 5 composites of high density exhibit remarkable mechanical properties. The influence of hot isostatic pressing (HIP) on the microstructure and the mechanical properties is investigated in cooperation with participants of the COST 503 activities and related to the strengthening and toughening mechanisms. Difficulties during densification by HIP arise from the evaporation of adsorbed volatiles as well as from the strong swelling of the powder compact due to the sintering reaction. Several HIP cycle designs were tested in order to prevent the bloating of the capsule and to control internal stresses due to the misfit of the thermal expansion of the entire phases. In comparison to single phase B 4 C ceramics, bending strength was improved to 1030 MPa, K Ic to 5.2 MPa/m, while hardness was comparable with HV1=38 GPa. Wear test were performed and related to the toughening mechanisms. (orig.) With 56 refs., 9 tabs., 64 figs

Void formation in ODS EUROFER produced by hot isostatic pressing

International Nuclear Information System (INIS)

Ortega, Y.; Monge, M.A.; Castro, V. de; Munoz, A.; Leguey, T.; Pareja, R.

2009-01-01

Positron annihilation experiments were performed on oxide dispersion strengthened (ODS) and non-ODS EUROFER prepared by mechanical alloying and hot isostatic pressing. The results revealed the presence of small voids in these materials in the as-HIPed conditions. Their evolution under isochronal annealing experiments was investigated. The coincidence Doppler broadening spectra of ODS EUROFER exhibited a characteristic signature attributed to positron annihilation in Ar-decorated voids at the oxide particle/matrix interfaces. The variation of the positron annihilation parameters with the annealing temperature showed three stages: up to 623 K, between 823 and 1323 K, and above 1323 K. In the temperature range 823-1323 K void coarsening had effect. Above 1323 K some voids annealed out, but others, associated to oxide particles and small precipitates, survived to annealing at 1523 K. Transmission electron microscopy observations were also performed to verify the characteristics of the surviving defects after annealing at 1523 K.

Void formation in ODS EUROFER produced by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Ortega, Y. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)], E-mail: yanicet@fis.ucm.es; Monge, M.A. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Castro, V. de [Department of Materials, University of Oxford, Oxford OX1 3PH (United Kingdom); Munoz, A.; Leguey, T.; Pareja, R. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)

2009-04-30

Positron annihilation experiments were performed on oxide dispersion strengthened (ODS) and non-ODS EUROFER prepared by mechanical alloying and hot isostatic pressing. The results revealed the presence of small voids in these materials in the as-HIPed conditions. Their evolution under isochronal annealing experiments was investigated. The coincidence Doppler broadening spectra of ODS EUROFER exhibited a characteristic signature attributed to positron annihilation in Ar-decorated voids at the oxide particle/matrix interfaces. The variation of the positron annihilation parameters with the annealing temperature showed three stages: up to 623 K, between 823 and 1323 K, and above 1323 K. In the temperature range 823-1323 K void coarsening had effect. Above 1323 K some voids annealed out, but others, associated to oxide particles and small precipitates, survived to annealing at 1523 K. Transmission electron microscopy observations were also performed to verify the characteristics of the surviving defects after annealing at 1523 K.

Nd:YAG transparent ceramics fabricated by direct cold isostatic pressing and vacuum sintering

Science.gov (United States)

Ge, Lin; Li, Jiang; Zhou, Zhiwei; Liu, Binglong; Xie, Tengfei; Liu, Jing; Kou, Huamin; Shi, Yun; Pan, Yubai; Guo, Jingkun

2015-12-01

The sintering behavior of neodymium doped yttrium aluminum garnet (Nd:YAG) ceramics was investigated on the basis of densification trajectory, microstructure evolution and transmittance. Nd:YAG ceramics with in-line transmittance of 83.9% at 1064 nm and 82.5% at 400 nm were obtained by direct cold isostatic pressing (CIP) at 250 MPa and solid-state reactive sintering at 1790 °C for 30 h under vacuum. Compared with the porosity and the average pore diameter of the sample from uniaxial dry-pressing followed by CIP, those from direct CIP are much smaller. The samples pressed at 250 MPa were sintered from 1500 °C to 1750 °C for 0.5-20 h to study their sintering behavior. At the temperature higher than 1500 °C, pure YAG phase is formed, followed by the densification and grain growth process. The relative density and the grain size increase with the increase of sintering time and temperature, and the sintering behavior is more sensitive to temperature than holding time. The mechanism controlling densification and grain growth at sintering temperature of 1550 °C is grain boundary diffusion.

Development of oxide dispersion strengthened W alloys produced by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Martinez, J.; Savoini, B.; Monge, M.A. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Munoz, A., E-mail: angel.munoz@uc3m.es [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Pareja, R. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)

2011-10-15

A powder metallurgy technique has been developed to produce oxide strengthened W-Ti and W-V alloys using elemental powders and nanosized powders of La{sub 2}O{sub 3} or Y{sub 2}O{sub 3} as starting materials. The alloys consolidated by hot isostatic pressing resulted in high-density materials having an ultrafine-grained structure and microhardness values in the range 7-13 GPa. Atom force microscopy studies show a topographic relief in the Ti and V pools that appear in the consolidated alloys. This relief is attributed to the heterogeneous nucleation of martensite plates. The preliminary transmission electron microscopy studies have revealed that a dispersion of nanoparticles can be induced in these alloys produced via the present technique.

Processing and properties of calcium phosphates bioceramics by hot isostatic pressing

Directory of Open Access Journals (Sweden)

Boilet Laurent

2013-11-01

Full Text Available Stoichiometric β-tricalcium phosphate (β-TCP, hydroxyapatite (HA and biphasic calcium phosphate (TCP/HA 60/40 %wt, BCP40 powders were synthesized by chemical precipitation of aqueous solutions of diammonium phosphate and calcium nitrate. After a calcination treatment and a milling step, powders were shaped by slip-casting. The sintering temperature effect on the density and the average grain size was investigated. By natural sintering, densities between 98 and 99.8% were obtained. Hot Isostatic Pressing (HIP treatment was carried out after a pre-sintering of these materials. Transparent or translucent samples were obtained, indicating a relative density very close to the theoretical value (>99.9%. Mechanical properties (three-point bending strength, fracture toughness, Young's modulus and Vickers hardness were measured on hipped materials with similar grain size (∼0.7μm.

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Brayshaw, W. J.; Sherry, A. H.

2018-03-01

Herein, we have performed J- Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP'd) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (- 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J 0.2BL, when compared to equivalently graded forged 304L, which is relatively constant across the tested temperature range.

An Assessment of the Ductile Fracture Behaviour of Hot Isostatically Pressed and Forged 304L Stainless Steel

OpenAIRE

Cooper, Adam; Smith, R. J.; Sherry, Andrew

2017-01-01

Type 300 austenitic stainless steel manufactured by hot isostatic pressing (HIP) has recently been shown to exhibit subtly different fracture behavior from that of equivalent graded forged steel, whereby the oxygen remaining in the component after HIP manifests itself in the austenite matrix as nonmetallic oxide inclusions. These inclusions facilitate fracture by acting as nucleation sites for the initiation, growth, and coalescence of microvoids in the plastically deforming austenite matrix....

FeCrAl and Zr alloys joined using hot isostatic pressing for fusion energy applications

International Nuclear Information System (INIS)

Park, Dong Jun; Kim, Hyun Gil; Park, Jeong Yong; Jung, Yang Il; Park, Jung Hwan; Koo, Yang Hyun

2016-01-01

Highlights: • FeCrAl and Zr alloys were successfully joined by hot isostatic pressing (HIP). • The thickness of diffusion layer increased with an increase in HIP temperature. • Significant inter-diffusion was observed for HIP at 1150 °C. • Maximum joint strength was achieved at HIP temperature of 700 °C. - Abstract: FeCrAl and Zr alloys were joined by a hot isostatic pressing (HIP) method for fusion energy applications. The optimum conditions for the joining process were studied. The HIP temperatures were varied from 700 to 1050 °C. The mechanical properties of the HIPed samples were evaluated by four-point bending and tensile tests. The FeCrAl and Zr alloys HIPed at 700 °C showed higher joint strength than the other samples. The joint strength decreased with an increase in the HIP temperature from 700 to 950 °C and significantly dropped at 1050 °C. Transmission electron microscopy, scanning electron microscopy, and optical microscopy were used to characterize the joints and interface region of the HIPed samples. The joints appeared to be tightly bonded and no intermetallic compounds or gaps were observed at the interface for HIP temperatures up to 950 °C. A diffusion layer formed at the interface and its thickness increased with the HIP temperature. HIP at 1050 °C, on the other hand, resulted in significant inter-diffusion and formation of brittle inter-metallic compounds at the interface.

Room temperature deformation mechanisms in ultrafine-grained materials processed by hot isostatic pressing

International Nuclear Information System (INIS)

Cao, W.Q.; Dirras, G.F.; Benyoucef, M.; Bacroix, B.

2007-01-01

Ultrafine-grained (uf-g) and microcrystalline-grained (mc-g) irons have been fabricated by hot isostatic pressing of nanopowders. The mechanical properties have been characterized by compressive tests at room temperature and the resulting microstructures and textures have been determined by combining electron back scatter diffraction and transmission electron microscopy. A transition of the deformation mode, from work hardening to work softening occurs for grain sizes below ∼1 μm, reflecting a transition of the deformation mode from homogeneous to localized deformation into shear bands (SBs). The homogeneous deformation is found to be lattice dislocation-based while the deformation within SBs involves lattice dislocations as well as boundary-related mechanisms, possibly grain boundary sliding accommodated by boundary opening

An Assessment of the Ductile Fracture Behavior of Hot Isostatically Pressed and Forged 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Smith, R. J.; Sherry, A. H.

2017-05-01

Type 300 austenitic stainless steel manufactured by hot isostatic pressing (HIP) has recently been shown to exhibit subtly different fracture behavior from that of equivalent graded forged steel, whereby the oxygen remaining in the component after HIP manifests itself in the austenite matrix as nonmetallic oxide inclusions. These inclusions facilitate fracture by acting as nucleation sites for the initiation, growth, and coalescence of microvoids in the plastically deforming austenite matrix. Here, we perform analyses based on the Rice-Tracey (RT) void growth model, supported by instrumented Charpy and J-integral fracture toughness testing at ambient temperature, to characterize the degree of void growth ahead of both a V-notch and crack in 304L stainless steel. We show that the hot isostatically pressed (HIP'd) 304L steel exhibits a lower critical void growth at the onset of fracture than that observed in forged 304L steel, which ultimately results in HIP'd steel exhibiting lower fracture toughness at initiation and impact toughness. Although the reduction in toughness of HIP'd steel is not detrimental to its use, due to the steel's sufficiently high toughness, the study does indicate that HIP'd and forged 304L steel behave as subtly different materials at a microstructural level with respect to their fracture behavior.

M3FT-17OR0301070211 - Preparation of Hot Isostatically Pressed AgZ Waste Form Samples

Energy Technology Data Exchange (ETDEWEB)

Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jordan, Jacob A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-10-01

The production of radioactive iodine-bearing waste forms that exhibit long-term stability and are suitable for permanent geologic disposal has been the subject of substantial research interest. One potential method of iodine waste form production is hot isostatic pressing (HIP). Recent studies at Oak Ridge National Laboratory (ORNL) have investigated the conversion of iodine-loaded silver mordenite (I-AgZ) directly to a waste form by HIP. ORNL has performed HIP with a variety of sample compositions and pressing conditions. The base mineral has varied among AgZ (in pure and engineered forms), silver-exchanged faujasite, and silverexchanged zeolite A. Two iodine loading methods, occlusion and chemisorption, have been explored. Additionally, the effects of variations in temperature and pressure of the process have been examined, with temperature ranges of 525°C–1,100°C and pressure ranges of 100–300 MPa. All of these samples remain available to collaborators upon request. The sample preparation detailed in this document is an extension of that work. In addition to previously prepared samples, this report documents the preparation of additional samples to support stability testing. These samples include chemisorbed I-AgZ and pure AgI. Following sample preparation, each sample was processed by HIP by American Isostatic Presses Inc. and returned to ORNL for storage. ORNL will store the samples until they are requested by collaborators for durability testing. The sample set reported here will support waste form durability testing across the national laboratories and will provide insight into the effects of varied iodine content on iodine retention by the produced waste form and on potential improvements in waste form durability provided by the zeolite matrix.

Effects of hot isostatic pressing on the elastic modulus and tensile properties of 316L parts made by powder bed laser fusion

International Nuclear Information System (INIS)

Lavery, N.P.; Cherry, J.; Mehmood, S.; Davies, H.; Girling, B.; Sackett, E.; Brown, S.G.R.; Sienz, J.

2017-01-01

The microstructure and mechanical properties of 316L steel have been examined for parts built by a powder bed laser fusion process, which uses a laser to melt and build parts additively on a layer by layer basis. Relative density and porosity determined using various experimental techniques were correlated against laser energy density. Based on porosity sizes, morphology and distributions, the porosity was seen to transition between an irregular, highly directional porosity at the low laser energy density and a smaller, more rounded and randomly distributed porosity at higher laser energy density, thought to be caused by keyhole melting. In both cases, the porosity was reduced by hot isostatic pressing (HIP). High throughput ultrasound based measurements were used to calculate elasticity properties and show that the lower porosities from builds with higher energy densities have higher elasticity moduli in accordance with empirical relationships, and hot isostatic pressing improves the elasticity properties to levels associated with wrought/rolled 316L. However, even with hot isostatic pressing the best properties were obtained from samples with the lowest porosity in the as-built condition. A finite element stress analysis based on the porosity microstructures was undertaken, to understand the effect of pore size distributions and morphology on the Young's modulus. Over 1–5% porosity range angular porosity was found to reduce the Young's modulus by 5% more than rounded porosity. Experimentally measured Young's moduli for samples treated by HIP were closer to the rounded trends than the as-built samples, which were closer to angular trends. Tensile tests on specimens produced at optimised machine parameters displayed a high degree of anisotropy in the build direction and test variability for as-built parts, especially between vertical and horizontal build directions. The as-built properties were generally found to have a higher yield stress, but lower upper

Effects of hot isostatic pressing on the elastic modulus and tensile properties of 316L parts made by powder bed laser fusion

Energy Technology Data Exchange (ETDEWEB)

Lavery, N.P., E-mail: N.P.Lavery@swansea.ac.uk [Materials Research Centre, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Zienkiewicz Centre for Computational Engineering, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Cherry, J.; Mehmood, S. [Materials Research Centre, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Zienkiewicz Centre for Computational Engineering, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Davies, H. [Materials Research Centre, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Girling, B.; Sackett, E. [Materials Research Centre, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Zienkiewicz Centre for Computational Engineering, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Brown, S.G.R. [Materials Research Centre, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom); Sienz, J. [Zienkiewicz Centre for Computational Engineering, College of Engineering, Swansea University Bay Campus, Fabian Way, Swansea SA1 8EP (United Kingdom)

2017-05-02

The microstructure and mechanical properties of 316L steel have been examined for parts built by a powder bed laser fusion process, which uses a laser to melt and build parts additively on a layer by layer basis. Relative density and porosity determined using various experimental techniques were correlated against laser energy density. Based on porosity sizes, morphology and distributions, the porosity was seen to transition between an irregular, highly directional porosity at the low laser energy density and a smaller, more rounded and randomly distributed porosity at higher laser energy density, thought to be caused by keyhole melting. In both cases, the porosity was reduced by hot isostatic pressing (HIP). High throughput ultrasound based measurements were used to calculate elasticity properties and show that the lower porosities from builds with higher energy densities have higher elasticity moduli in accordance with empirical relationships, and hot isostatic pressing improves the elasticity properties to levels associated with wrought/rolled 316L. However, even with hot isostatic pressing the best properties were obtained from samples with the lowest porosity in the as-built condition. A finite element stress analysis based on the porosity microstructures was undertaken, to understand the effect of pore size distributions and morphology on the Young's modulus. Over 1–5% porosity range angular porosity was found to reduce the Young's modulus by 5% more than rounded porosity. Experimentally measured Young's moduli for samples treated by HIP were closer to the rounded trends than the as-built samples, which were closer to angular trends. Tensile tests on specimens produced at optimised machine parameters displayed a high degree of anisotropy in the build direction and test variability for as-built parts, especially between vertical and horizontal build directions. The as-built properties were generally found to have a higher yield stress, but

Isostatic compression of buffer blocks. Middle scale

International Nuclear Information System (INIS)

Ritola, J.; Pyy, E.

2012-01-01

Manufacturing of buffer components using isostatic compression method has been studied in small scale in 2008 (Laaksonen 2010). These tests included manufacturing of buffer blocks using different bentonite materials and different compression pressures. Isostatic mould technology was also tested, along with different methods to fill the mould, such as vibration and partial vacuum, as well as a stepwise compression of the blocks. The development of manufacturing techniques has continued with small-scale (30 %) blocks (diameter 600 mm) in 2009. This was done in a separate project: Isostatic compression, manufacturing and testing of small scale (D = 600 mm) buffer blocks. The research on the isostatic compression method continued in 2010 in a project aimed to test and examine the isostatic manufacturing process of buffer blocks at 70 % scale (block diameter 1200 to 1300 mm), and the aim was to continue in 2011 with full-scale blocks (diameter 1700 mm). A total of nine bentonite blocks were manufactured at 70 % scale, of which four were ring-shaped and the rest were cylindrical. It is currently not possible to manufacture full-scale blocks, because there is no sufficiently large isostatic press available. However, such a compression unit is expected to be possible to use in the near future. The test results of bentonite blocks, produced with an isostatic pressing method at different presses and at different sizes, suggest that the technical characteristics, for example bulk density and strength values, are somewhat independent of the size of the block, and that the blocks have fairly homogenous characteristics. Water content and compression pressure are the two most important properties determining the characteristics of the compressed blocks. By adjusting these two properties it is fairly easy to produce blocks at a desired density. The commonly used compression pressure in the manufacturing of bentonite blocks is 100 MPa, which compresses bentonite to approximately

Isostatic compression of buffer blocks. Middle scale

Energy Technology Data Exchange (ETDEWEB)

Ritola, J.; Pyy, E. [VTT Technical Research Centre of Finland, Espoo (Finland)

2012-01-15

Manufacturing of buffer components using isostatic compression method has been studied in small scale in 2008 (Laaksonen 2010). These tests included manufacturing of buffer blocks using different bentonite materials and different compression pressures. Isostatic mould technology was also tested, along with different methods to fill the mould, such as vibration and partial vacuum, as well as a stepwise compression of the blocks. The development of manufacturing techniques has continued with small-scale (30 %) blocks (diameter 600 mm) in 2009. This was done in a separate project: Isostatic compression, manufacturing and testing of small scale (D = 600 mm) buffer blocks. The research on the isostatic compression method continued in 2010 in a project aimed to test and examine the isostatic manufacturing process of buffer blocks at 70 % scale (block diameter 1200 to 1300 mm), and the aim was to continue in 2011 with full-scale blocks (diameter 1700 mm). A total of nine bentonite blocks were manufactured at 70 % scale, of which four were ring-shaped and the rest were cylindrical. It is currently not possible to manufacture full-scale blocks, because there is no sufficiently large isostatic press available. However, such a compression unit is expected to be possible to use in the near future. The test results of bentonite blocks, produced with an isostatic pressing method at different presses and at different sizes, suggest that the technical characteristics, for example bulk density and strength values, are somewhat independent of the size of the block, and that the blocks have fairly homogenous characteristics. Water content and compression pressure are the two most important properties determining the characteristics of the compressed blocks. By adjusting these two properties it is fairly easy to produce blocks at a desired density. The commonly used compression pressure in the manufacturing of bentonite blocks is 100 MPa, which compresses bentonite to approximately

Yb:Y2O3 transparent ceramics processed with hot isostatic pressing

Science.gov (United States)

Wang, Jun; Ma, Jie; Zhang, Jian; Liu, Peng; Luo, Dewei; Yin, Danlei; Tang, Dingyuan; Kong, Ling Bing

2017-09-01

Highly transparent 5 at.% Yb:Y2O3 ceramics were fabricated by using a combination method of vacuum sintering and hot isostatic pressing (HIP). Co-precipitated Yb:Y2O3 powders, with 1 at.% ZrO2 as the sintering aid, were used as the starting material. The Yb:Y2O3 ceramics, vacuum sintered at 1700 °C for 2 h and HIPed at 1775 °C for 4 h, exhibited small grain size of 1.9 μm and highly dense microstructure. In-line optical transmittance of the ceramics reached 83.4% and 78.9% at 2000 and 600 nm, respectively. As the ceramic slab was pumped by a fiber-coupled laser diode at about 940 nm, a maximum output power of 0.77 W at 1076 nm was achieved, with a corresponding slope efficiency of 10.6%.

Transformation of Cs-IONSIV® into a ceramic wasteform by hot isostatic pressing

Science.gov (United States)

Chen, Tzu-Yu; Maddrell, Ewan R.; Hyatt, Neil C.; Gandy, Amy S.; Stennett, Martin C.; Hriljac, Joseph A.

2018-01-01

A simple method to directly convert Cs-exchanged IONSIV® IE-911 into a ceramic wasteform by hot isostatic pressing (1100 °C/190 MPa/2 hr) is presented. Two major Cs-containing phases, Cs2TiNb6O18 and Cs2ZrSi6O15, and a series of mixed oxides form. The microstructure and phase assemblage of the samples as a function of Cs content were examined using XRD, XRF, SEM and TEM/EDX. The chemical aqueous durability of the materials was investigated using the MCC-1 and PCT-B standard test methods. For HIPed Cs-IONSIV® samples, the MCC-1 normalised release rates of Cs were low rates are indicative of a safe long-term immobilisation matrix for Cs formed directly from spent IONSIV®. It was also demonstrated that the phase formation can be altered by adding Ti metal due to a controlled redox environment.

Development of Be/Glidcop joint obtained by hot isostatic pressing diffusion bonding for high in-service temperature

Energy Technology Data Exchange (ETDEWEB)

Saint-Antonin, F.; Bucci, P.; Burlet, H.; Le Marois, G. [CEA Centre d`Etudes de Grenoble, 38 (France); Barberi, D.; Laille, A.

1998-01-01

This paper addresses some aspects of the beryllium-Glidcop joining by Hot Isostatic Pressing diffusion Bonding. The quality of a joint is mainly dependent on the interface microstructure. Thus, as Be/copper direct bonding is not recommended, the choice of interlayers is a critical point. The joining process parameters, i.e. temperature, pressure and time, must take into account the in-service requirements, the mechanical and metallurgical properties of each material. The Be/Glidcop joining process developed at CEA/Grenoble is presented here. (author)

Pore annihilation in a single-crystal nickel-base superalloy during hot isostatic pressing: Experiment and modelling

International Nuclear Information System (INIS)

Epishin, Alexander; Fedelich, Bernard; Link, Thomas; Feldmann, Titus; Svetlov, Igor L.

2013-01-01

Pore annihilation during hot isostatic pressing (HIP) was investigated in the single-crystal nickel-base superalloy CMSX-4 experimentally by interrupted HIP tests at 1288 °C/103 MPa. The kinetics of pore annihilation was determined by density measurement and quantitative metallography. Transmission electron microscopy of a HIPed specimen showed that the pores shrink via dislocation movement on octahedral glide planes. Theoretically pore closure under HIP condition was modelled by the finite element method using crystal plasticity and large strain theories. The modelling gives a similar kinetics of pore annihilation as observed experimentally, however somewhat higher annihilation rate

Effect of Tooling Material on the Internal Surface Quality of Ti6Al4V Parts Fabricated by Hot Isostatic Pressing

Science.gov (United States)

Cai, Chao; Song, Bo; Wei, Qingsong; Yan, Wu; Xue, Pengju; Shi, Yusheng

2017-01-01

For the net-shape hot isostatic pressing (HIP) process, control of the internal surface roughness of as-HIPped parts remains a challenge for practical engineering. To reveal the evolution mechanism of the internal surface of the parts during the HIP process, the effect of different tooling materials (H13, T8, Cr12 steel, and graphite) as internal cores on the interfacial diffusion and surface roughness was systematically studied.

Characterization of 316L(N)-IG SS joint produced by hot isostatic pressing technique

International Nuclear Information System (INIS)

Nakano, J.; Miwa, Y.; Tsukada, T.; Kikuchi, M.; Kita, S.; Nemoto, Y.; Tsuji, H.; Jitsukawa, S.

2002-01-01

Type 316L(N) stainless steel of the international thermonuclear experimental reactor grade (316L(N)-IG SS) is being considered for the first wall/blanket module. Hot isostatic pressing (HIP) technique is expected for the fabrication of the module. To evaluate the integrity and susceptibility to stress corrosion cracking (SCC) of HIPed 316L(N)-IG SS, tensile tests in vacuum and slow strain rate tests in high temperature water were performed. Specimen with the HIPed joint had similar tensile properties to specimens of 316L(N)-IG SS, and did not show susceptibility to SCC in oxygenated water at 423 K. Thermally sensitized specimen was low susceptible to SCC even in the creviced condition. It is concluded that the tensile properties of HIPed SS are as high as those of the base alloy and the HIP process caused no deleterious effects

Process and equipment development for hot isostatic pressing treatability study

Energy Technology Data Exchange (ETDEWEB)

Bateman, Ken; Wahlquist, Dennis; Malewitz, Tim

2015-03-01

Battelle Energy Alliance (BEA), LLC, has developed processes and equipment for a pilot-scale hot isostatic pressing (HIP) treatability study to stabilize and volume reduce radioactive calcine stored at Idaho National Laboratory (INL). In 2009, the U. S. Department of Energy signed a Record of Decision with the state of Idaho selecting HIP technology as the method to treat 5,800 yd^3 (4,400 m^3) of granular zirconia and alumina calcine produced between 1953 and 1992 as a waste byproduct of spent nuclear fuel reprocessing. Since the 1990s, a variety of radioactive and hazardous waste forms have been remotely treated using HIP within INL hot cells. To execute the remote process at INL, waste is loaded into a stainless-steel or aluminum can, which is evacuated, sealed, and placed into a HIP furnace. The HIP simultaneously heats and pressurizes the waste, reducing its volume and increasing its durability. Two 1 gal cans of calcine waste currently stored in a shielded cask were identified as candidate materials for a treatability study involving the HIP process. Equipment and materials for cask-handling and calcine transfer into INL hot cells, as well as remotely operated equipment for waste can opening, particle sizing, material blending, and HIP can loading have been designed and successfully tested. These results demonstrate BEA’s readiness for treatment of INL calcine.

Microstructural and mechanical characteristics of W–2Ti and W–1TiC processed by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Muñoz, A., E-mail: angel.munoz@uc3m.es [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad, 30, E28911 Leganés (Spain); Savoini, B. [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad, 30, E28911 Leganés (Spain); Tejado, E. [Departamento de Ciencia de Materiales, E.T.S. I. de Ingenieros de Caminos, Canales y Puertos, Universidad Politécnica de Madrid, E28040 Madrid (Spain); Centro Nacional de Investigaciones Metalúrgicas (C.S.I.C), Av. Gregorio del Amo, 8, E2840 Madrid (Spain); Monge, M.A. [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad, 30, E28911 Leganés (Spain); Pastor, J.Y. [Departamento de Ciencia de Materiales, E.T.S. I. de Ingenieros de Caminos, Canales y Puertos, Universidad Politécnica de Madrid, E28040 Madrid (Spain); Pareja, R. [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad, 30, E28911 Leganés (Spain)

2014-12-15

W–2Ti and W–1TiC alloys were produced by mechanical alloying and consolidation by hot isostatic pressing. The composition and microstructural characteristics of these alloys were studied by X-ray diffraction, energy dispersion spectroscopy and scanning electron microscopy. The mechanical behavior of the consolidated alloys was characterized by microhardness measurements and three point bending tests. The mechanical characteristics of the W–2Ti alloy appear to be related to solution hardening. In W–1TiC, the residual porosity should be responsible for the poor behavior observed in comparison with W–2Ti.

Microstructural and mechanical characteristics of W–2Ti and W–1TiC processed by hot isostatic pressing

International Nuclear Information System (INIS)

Muñoz, A.; Savoini, B.; Tejado, E.; Monge, M.A.; Pastor, J.Y.; Pareja, R.

2014-01-01

W–2Ti and W–1TiC alloys were produced by mechanical alloying and consolidation by hot isostatic pressing. The composition and microstructural characteristics of these alloys were studied by X-ray diffraction, energy dispersion spectroscopy and scanning electron microscopy. The mechanical behavior of the consolidated alloys was characterized by microhardness measurements and three point bending tests. The mechanical characteristics of the W–2Ti alloy appear to be related to solution hardening. In W–1TiC, the residual porosity should be responsible for the poor behavior observed in comparison with W–2Ti

Optimizing the Synthesis of Alumina Inserts Using Hot Isostatic Pressing (HIP)

Science.gov (United States)

Ariff, T. F.; Azhar, A. Z.; Sariff, M. N.; Rasid, S. N.; Zahari, S. Z.; Bahar, R.; Karim, M.; Nurul Amin, AKM

2018-01-01

Alumina or Aluminium Oxide (Al2O3) is well known for its high strength and hardness. Its low heat retention and low specific heat characteristics make it attractive to be used widely as a cutting tool for grinding, milling and turning processes. Various synthesis methods have been used for the purpose of enhancing the properties of the alumina inserts. However, the optimization process using Hot Isostatic Pressing (HIP) has not been performed. This research aims in finding the optimum parameters in synthesizing the alumina inserts (98Al2O3 1.6ZrO2 0.4MgO, 93Al2O3 6.4ZrO2 0.6MgO and 85Al2O3 14.5ZrO2 0.5MgO) using HIP at different temperatures (1200, 1250 and 1300°C) and sintering time (10, 30 and 60 minutes). Hardness, density, shrinkage and microstructure using SEM were analysed. The optimum sintering condition for the alumina insert was found in 98Al2O3 1.6ZrO2 0.4MgO sintered at 1300°C for 60 minutes for it exhibited the highest values of hardness (1917HV), density (3.95g/cm3), shrinkage (9.6%).

High temperature mechanical performance of a hot isostatically pressed silicon nitride

Energy Technology Data Exchange (ETDEWEB)

Wereszczak, A.A.; Ferber, M.K.; Jenkins, M.G.; Lin, C.K.J. [and others

1996-01-01

Silicon nitride ceramics are an attractive material of choice for designers and manufacturers of advanced gas turbine engine components for many reasons. These materials typically have potentially high temperatures of usefulness (up to 1400{degrees}C), are chemically inert, have a relatively low specific gravity (important for inertial effects), and are good thermal conductors (i.e., resistant to thermal shock). In order for manufacturers to take advantage of these inherent properties of silicon nitride, the high-temperature mechanical performance of the material must first be characterized. The mechanical response of silicon nitride to static, dynamic, and cyclic conditions at elevated temperatures, along with reliable and representative data, is critical information that gas turbine engine designers and manufacturers require for the confident insertion of silicon nitride components into gas turbine engines. This final report describes the high-temperature mechanical characterization and analyses that were conducted on a candidate structural silicon nitride ceramic. The high-temperature strength, static fatigue (creep rupture), and dynamic and cyclic fatigue performance were characterized. The efforts put forth were part of Work Breakdown Structure Subelement 3.2.1, {open_quotes}Rotor Data Base Generation.{close_quotes} PY6 is comparable to other hot isostatically pressed (HIPed) silicon nitrides currently being considered for advanced gas turbine engine applications.

Verification of the effect of surface preparation on Hot Isostatic Pressing diffusion bonding joints of CLAM steel

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yanyun [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Chunjing, E-mail: chunjing.li@fds.org.cn [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huang, Bo; Liu, Shaojun [Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Huang, Qunying [University of Science and Technology of China, Hefei, Anhui 230027 (China); Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

2014-12-15

Hot Isostatic Pressing (HIP) diffusion bonding with CLAM steel is the primary candidate fabrication technique for the first wall (FW) of DFLL-TBM. Surface state is one of the key factors for the joints quality. The effect of surface state prepared with grinder and miller on HIP diffusion bonding joints of CLAM steel was investigated. HIP diffusion bonding was performed at 140 MPa and 1373 K within 3 h. The mechanical properties of the joints were investigated with instrumented Charpy V-notch impact tests and the microstructures of the joints were analyzed with scanning electron microscopy (SEM). The results showed that the milled samples with fine surface roughness were more suitable for CLAM steel HIP diffusion bonding.

Properties of hot pressed MgB2/Ti tapes

International Nuclear Information System (INIS)

Kovac, P.; Husek, I.; Melisek, T.; Fedor, J.; Cambel, V.; Morawski, A.; Kario, A.

2009-01-01

Hot axial and hot isostatic pressing was applied for single-core MgB 2 /Ti tapes. Differences in transport current density, n-exponents and critical current anisotropy are discussed and related to the grain connectivity influenced by pressing. The magnetic Hall probe scanning measurements allowed observing the isolated regions for axially hot pressed sample attributed to the longitudinally oriented cracks introduced by pressing. The highest current densities were measured for the tape subjected to hot isostatic pressing due to improved connectivity.

Inversion defects in MgAl2O4 elaborated by pressureless sintering, pressureless sintering plus hot isostatic pressing, and spark plasma sintering

International Nuclear Information System (INIS)

Mussi, A.; Granger, G. Bernard; Addad, A.; Benameur, N.; Beclin, F.; Bataille, A.

2009-01-01

The distribution of inversion defects of Al was investigated in dense magnesium-aluminate spinel elaborated by pressureless sintering, pressureless sintering plus hot isostatic pressing, and spark plasma sintering. This study was conducted by energy electron loss spectroscopy analyses and more particularly by energy loss near edge structure investigations of the Al-L 2,3 edge. Several aspects are discussed with the purpose of understanding why charged defects dispersal reveals a special configuration.

Effect of reduced cobalt contents on hot isostatically pressed powder metallurgy U-700 alloys

Science.gov (United States)

Harf, F. H.

1982-01-01

The effect of reducing the cobalt content of prealloyed powders of UDIMET 700 (U-700) alloys to 12.7, 8.6, 4.3, and 0% was examined. The powders were hot isostatically pressed into billets, which were given heat treatments appropriate for turbine disks, namely partial solutioning at temperatures below the gamma prime solvus and four step aging treatments. Chemical analyses, metallographic examinations, and X-ray diffraction measurements were performed on the materials. Minor effects on gamma prime content and on room temperature and 650 C tensile properties were observed. Creep rupture lives at 650 C reached a maximum at the 8.4% concentration, while at 760 C a maximum in life was reached at the 4.3% cobalt level. Minimum creep rates increased with decreasing cobalt content at both test temperatures. Extended exposures at 760 and 815 C resulted in decreased tensile strengths and rupture lives for all alloys. Evidence of sigma phase formation was also found.

Influence of cold isostatic pressing on the magnetic properties of Ni-Zn-Cu ferrite

Science.gov (United States)

Le, Trong Trung; Valdez-Nava, Zarel; Lebey, Thierry; Mazaleyrat, Frédéric

2018-04-01

In power electronics, there is the need to develop solutions to increase the power density of converters. Interleaved multicellular transformers allow interleaving many switching cells and, as a result, a possible increase in the power density. This converter is often composed of a magnetic core having the function of an intercell transformer (ICT) and, depending on the complexity of the designed architecture, its shape could be extremely complex. The switching frequencies (1-10 MHz) for the new wide band gap semiconductors (SiC, GaN) allow to interleave switching cell at higher frequencies than silicon-based semiconductors (materials, but their limit in frequency drive raises the need of higher frequency magnetic materials, such Ni-Zn ferrites. These materials can operate in medium and high power converters up to 10 MHz. We propose to use Ni0,30Zn0,57Cu0,15Fe2O4 ferrite and to compress it by cold isostatic pressing (CIP) into a a green ceramic block and to machine it to obtain the desired ICT of complex shape prior sintering. We compare the magnetic permeability spectra and hysteresis loops the CIP and uniaxially pressed ferrites. The effect of temperature and sintering time as well as high-pressure on properties will be presented in detail. The magnetic properties of the sintered cores are strongly dependent on the microstructure obtained.

Fundamental Aspects of Zeolite Waste Form Production by Hot Isostatic Pressing

Energy Technology Data Exchange (ETDEWEB)

Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jordan, Jacob A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-02-01

The direct conversion of iodine-bearing sorbents into a stable waste form is a research topic of interest to the US Department of Energy. The removal of volatile radioactive 129I from the off-gas of a nuclear fuel reprocessing facility will be necessary in order to comply with the regulatory requirements that apply to facilities sited within the United States (Jubin et al., 2012a), and any iodine-containing media or solid sorbents generated by this process would contain ¹²⁹I and would be destined for eventual geological disposal. While recovery of iodine from some sorbents is possible, a method to directly convert iodineloaded sorbents to a durable waste form with little or no additional waste materials being formed and a potentially reduced volume would be beneficial. To this end, recent studies have investigated the conversion of iodine-loaded silver mordenite (I-AgZ) directly to a waste form by hot isostatic pressing (HIPing) (Bruffey and Jubin, 2015). Silver mordenite (AgZ), of the zeolite class of minerals, is under consideration for use in adsorbing iodine from nuclear reprocessing off-gas streams. Direct conversion of I-AgZ by HIPing may provide the following benefits: (1) a waste form of high density that is tolerant to high temperatures, (2) a waste form that is not significantly chemically hazardous, and (3) a robust conversion process that requires no pretreatment.

Comparative evaluation of electrical conductivity of hydroxyapatite ceramics densified through ramp and hold, spark plasma and post sinter Hot Isostatic Pressing routes

Energy Technology Data Exchange (ETDEWEB)

Buchi Suresh, M., E-mail: suresh@arci.res.in; Biswas, P.; Mahender, V.; Johnson, Roy, E-mail: royjohnson@arci.res.in

2017-01-01

Hydroxyapatite ceramics synthesized through sonochemical route were processed and densified through ramp & hold (R&H) and Spark Plasma Sintering (SPS) routes. The effect of processing route on the relative density and electrical conductivity were studied. Further, the samples were Hot Isostatically Pressed (HIP) under argon pressure at elevated temperature to further densify the sample. All these samples processed under different conditions were characterized by X-ray diffraction, Scanning Electron Microscopy and AC Conductivity. The samples have exhibited hydroxyapatite phase; however, microstructures exhibited distinctly different grain morphologies and grain sizes. AC impedance spectroscopic measurement was carried out on hydroxyapatite samples processed through different routes and the corresponding spectra were analyzed by the analogy to equivalent circuit involving resistors and capacitors. SPS sintered sample after HIPing has exhibited the highest conductivity. This can be attributed to the higher density in combination with finer grain sizes. Activation energy based on Arrhenius equation is calculated and the prominent conduction mechanism is proposed. - Highlights: • Hot Isostatic Pressing (HIP) of SPS and R&H processed samples has resulted into densities near to theoretical densities • No change in the crystal structure is observed in SPS and R&H samples before and after HIP treatment • SPS processed and HIP treated samples resulted into higher conductivities with smaller grain sizes and grain boundary area.

Age hardening in rapidly solidified and hot isostatically pressed beryllium-aluminum-silver alloys

International Nuclear Information System (INIS)

Carter, D.H.; McGeorge, A.C.; Jacobson, L.A.; Stanek, P.W.

1995-01-01

Three different alloys of beryllium, aluminum and silver were processed to powder by centrifugal atomization in a helium atmosphere. Alloy compositions were, by weight, 50% Be, 47.5% Al, 2.5% Ag, 50% Be, 47% Al, 3% Ag, and 50% Be, 46% Al, 4% Ag. Due to the low solubility of both aluminum and silver in beryllium, the silver was concentrated in the aluminum phase, which appeared to separate from the beryllium in the liquid phase. A fine, continuous composite beryllium-aluminum microstructure was formed, which did not significantly change after hot isostatically pressing at 550 C for one hour at 30,000 psi argon pressure. Samples of HIP material were solution treated at 550 C for one hour, followed by a water quench. Aging temperatures were 150, 175, 200 and 225 C for times ranging from one half hour to 65 hours. Hardness measurements were made using a diamond pyramid indenter with a load of 1 kg. Results indicate that peak hardness was reached in 36--40 hours at 175 C and 12--16 hours at 200 C aging temperature, relatively independent of alloy composition

The substitution of nickel for cobalt in hot isostatically pressed powder metallurgy UDIMET 700 alloys

Science.gov (United States)

Harf, F. H.

1985-01-01

Nickel was substituted in various proportions for cobalt in a series of five hot-isostatically-pressed powder metallurgy alloys based on the UDIMET 700 composition. These alloys were given 5-step heat treatments appropriate for use in turbine engine disks. The resultant microstructures displayed three distinct sizes of gamma-prime particles in a gamma matrix. The higher cobalt-content alloys contained larger amounts of the finest gamma-prime particles, and had the lowest gamma-gamma-prime lattice mismatch. While all alloys had approximately the same tensile properties at 25 and 650 gamma C, the rupture lives at 650 and 760 C peaked in the alloys with cobalt contents between 12.7 and 4.3 pct. Minimum creep rates increased as cobalt contents were lowered, suggesting their correlation with the gamma-prime particle size distribution and the gamma-gamma-prime mismatch. It was also found that, on overaging at temperatures higher than suitable for turbine disk use, the high cobalt-content alloys were prone to sigma phase formation.

Cyclic fatigue resistance of yttria-stabilized tetragonal zirconia polycrystals with hot isostatic press processing.

Science.gov (United States)

Koyama, Taku; Sato, Toru; Yoshinari, Masao

2012-01-01

This study investigated the influence of surface roughness and cyclic loading on fatigue resistance in Y-TZP subjected to hot isostatic pressing (HIP). Fifty Y-TZP cylinders 3.0 mm in diameter were divided into Group A (polished by centerless method; TZP-CP) or Group B (blasted and acid-etched: TZP-SB150E). Twenty five cp-titanium cylinders (Ti-SB150E) were used as a control. Static and cyclic tests were carried out according to ISO 14801. The cyclic fatigue test was performed in distilled water at 37°C. Surface morphology and roughness as well as crystal phase on the surfaces were also evaluated. Fracture force under the static test was 1,765N (TZP-CP), 1,220N (TZP-SB150E), and 850 N (yield force, Ti-SB150E). Fracture values under the cyclic test decreased to approximately 70% of those under the static tests. These results indicate that HIPed Y-TZP with a 3.0-mm diameter has sufficient durability for application to dental implants.

Hot Isostatic Pressing of Engineered Forms of I-AgZ

Energy Technology Data Exchange (ETDEWEB)

Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Watkins, Thomas R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jordan, Jacob A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parks, Mackenzie L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-11-01

Hot isostatic pressing (HIP) is being considered for direct conversion of ¹²⁹I-bearing materials to a radiological waste form. The removal of volatile radioactive ¹²⁹I from the off-gas of a nuclear fuel reprocessing facility will be necessary to comply with regulatory requirements regarding reprocessing facilities sited within the United States, and any iodine-containing media or solid sorbents generated by offgas abatement will require disposal. Zeolite minerals such as silver-exchanged mordenite (AgZ) have been studied as potential iodine sorbents and will contain ¹²⁹I as chemisorbed AgI. Oak Ridge National Laboratory (ORNL) has conducted several recent studies on the HIP of both iodine-loaded AgZ (I-AgZ) and other iodine-bearing zeolite minerals. The goal of these research efforts is to achieve a stable, highly leach resistant material that is reduced in volume as compared to bulk iodine-loaded I-AgZ. Through the use of HIP, it may be possible to achieve this with the addition of little or no additional materials (waste formers). Other goals for the process include that the waste form will be tolerant to high temperatures and pressures, not chemically hazardous, and that the process will result in minimal secondary waste generation. This document describes the preparation of 27 samples that are distinct from previous efforts in that they are prepared exclusively with an engineered form of AgZ that is manufactured using a binder. Iodine was incorporated solely by chemisorption. This base material is expected to be more representative of an operational system than were samples prepared previously with pure minerals.

Hot-isostatic pressing of U-10Zr by grain boundary diffusion and creep cavitation. Part 2: Theory and data analysis

International Nuclear Information System (INIS)

McDeavitt, S.M.; Solomon, A.A.

1997-01-01

Uranium-10 wt % zirconium (U-10Zr) is a fuel alloy that has been used in the Experimental Breeder Reactor-II (EBR-II). The high burnup that was desired in this fuel system made high demands on the mechanical compatibility between fuel and cladding both during normal operation and during safety-related transients when rapid differential expansion may cause high stresses. In general, this mechanical stress can be reduced by cladding deformation if the cladding is sufficiently ductile at high burnup, and/or by fuel hot-pressing. Fortunately, the fuel is very porous when it contacts the cladding, but this porosity gradually fills with solid fission products (primarily lanthanides) that may limit the fuel's compressibility. If the porosity remains open, gaseous fission products are released and the porous fuel creeps rather than hot-presses under contact stresses. If the pores are closed by sintering or by solid fission products, the porous fuel will hot-isostatic press (HIP), as represented by the models to be discussed. HIP experiments performed at 700 C on U-10Zr samples with different impurity phase contents (Part 1) are analyzed in terms of several creep cavitation models. The coupled diffusion/creep cavitation model of Chen and Argon shows good quantitative agreement with measured HIP rates for hydride- and metal-derived U-10Zr materials, assuming that pores are uniformly distributed on grain boundaries and are of modal size, and that far-field strain rates are negligible. The analysis predicts, for the first time, an asymmetry between HIP and swelling at identical pressure-induced driving forces due to differences in grain boundary stresses. The differences in compressibility of hydride- and metal-derived U-10Zr can be partially explained by differences in pore size and spacing. The relevance of the experiments to description of in-reactor densification under external pressure or contact stress due to fuel/cladding mechanical interaction is discussed

Tensile and fracture characteristics of oxide dispersion strengthened Fe–12Cr produced by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Castro, Vanessa de, E-mail: vanessa.decastro@uc3m.es [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad 30, 28911 Leganés, Madrid (Spain); Garces-Usan, Jose Maria; Leguey, Teresa; Pareja, Ramiro [Departamento de Física, Universidad Carlos III de Madrid, Avda. de la Universidad 30, 28911 Leganés, Madrid (Spain)

2013-11-15

The mechanical characteristics of a model oxide dispersion strengthened (ODS) alloy with nominal composition Fe–12 wt%Cr–0.4 wt%Y{sub 2}O{sub 3} were investigated by means of microhardness measurements, tensile tests up to fracture in the temperature range of 298–973 K, and fracture surface analyses. A non-ODS Fe–12 wt%Cr alloy was also studied to assess the real capacity of the oxide dispersion for strengthening the alloy. The materials were produced by mechanical alloying followed by hot isostatic pressing consolidation and heat treatment at 1023 K. The strengthening effect of the oxide nanodispersion was effective at all temperatures studied, although the tensile strength converges towards the one obtained for the reference alloy at higher temperatures. Moreover, the ODS alloys failed prematurely at T < 673 K due to the presence of Y-rich inclusions, as seen in the fracture surface of these alloys.

Tensile and fracture characteristics of oxide dispersion strengthened Fe–12Cr produced by hot isostatic pressing

International Nuclear Information System (INIS)

Castro, Vanessa de; Garces-Usan, Jose Maria; Leguey, Teresa; Pareja, Ramiro

2013-01-01

The mechanical characteristics of a model oxide dispersion strengthened (ODS) alloy with nominal composition Fe–12 wt%Cr–0.4 wt%Y 2 O 3 were investigated by means of microhardness measurements, tensile tests up to fracture in the temperature range of 298–973 K, and fracture surface analyses. A non-ODS Fe–12 wt%Cr alloy was also studied to assess the real capacity of the oxide dispersion for strengthening the alloy. The materials were produced by mechanical alloying followed by hot isostatic pressing consolidation and heat treatment at 1023 K. The strengthening effect of the oxide nanodispersion was effective at all temperatures studied, although the tensile strength converges towards the one obtained for the reference alloy at higher temperatures. Moreover, the ODS alloys failed prematurely at T < 673 K due to the presence of Y-rich inclusions, as seen in the fracture surface of these alloys

Influence of cold isostatic pressing on the magnetic properties of Ni-Zn-Cu ferrite

Directory of Open Access Journals (Sweden)

Trong Trung Le

2018-04-01

Full Text Available In power electronics, there is the need to develop solutions to increase the power density of converters. Interleaved multicellular transformers allow interleaving many switching cells and, as a result, a possible increase in the power density. This converter is often composed of a magnetic core having the function of an intercell transformer (ICT and, depending on the complexity of the designed architecture, its shape could be extremely complex. The switching frequencies (1-10 MHz for the new wide band gap semiconductors (SiC, GaN allow to interleave switching cell at higher frequencies than silicon-based semiconductors (<1 MHz. Intercell transformers must follow this increase in frequency times-fold the number of switching cells. Current applications for ICT transformers use Mn-Zn based materials, but their limit in frequency drive raises the need of higher frequency magnetic materials, such Ni-Zn ferrites. These materials can operate in medium and high power converters up to 10 MHz. We propose to use Ni0,30Zn0,57Cu0,15Fe2O4 ferrite and to compress it by cold isostatic pressing (CIP into a a green ceramic block and to machine it to obtain the desired ICT of complex shape prior sintering. We compare the magnetic permeability spectra and hysteresis loops the CIP and uniaxially pressed ferrites. The effect of temperature and sintering time as well as high-pressure on properties will be presented in detail. The magnetic properties of the sintered cores are strongly dependent on the microstructure obtained.

Forming and control of pores by capsule-free hot isostatic pressing in NiTi shape memory alloys

International Nuclear Information System (INIS)

Yuan, B; Zhu, M; Gao, Y; Li, X; Chung, C Y

2008-01-01

In this study, the pore evolution process of porous NiTi shape memory alloys (SMAs) fabricated by capsule-free hot isostatic pressing (CF-HIP) was investigated by adopting different fabricating parameters. It is shown that porous NiTi SMAs with homogeneous pore distribution and nearly spherical pore shape can be prepared by CF-HIP under suitable conditions. In addition, two novel pore structures were produced, one with a sandwich-like structure, and another with controlled gradient of porosity along the radial direction, with pore size increasing from the outside towards the center of the specimen. The former was obtained by balancing the pressure in the HIP chamber and the gas pressure resulting from the gas expansion in the green sample. The latter resulted from the formation of air bubbles in the liquid phase during the sintering

Effects of Temperature and Pressure of Hot Isostatic Pressing on the Grain Structure of Powder Metallurgy Superalloy.

Science.gov (United States)

Tan, Liming; He, Guoai; Liu, Feng; Li, Yunping; Jiang, Liang

2018-02-24

The microstructure with homogeneously distributed grains and less prior particle boundary (PPB) precipitates is always desired for powder metallurgy superalloys after hot isostatic pressing (HIPping). In this work, we studied the effects of HIPping parameters, temperature and pressure on the grain structure in PM superalloy FGH96, by means of scanning electron microscope (SEM), electron backscatter diffraction (EBSD), transmission electron microscope (TEM) and Time-of-flight secondary ion spectrometry (ToF-SIMS). It was found that temperature and pressure played different roles in controlling PPB precipitation and grain structure during HIPping, the tendency of grain coarsening under high temperature could be inhibited by increasing HIPping pressure which facilitates the recrystallization. In general, relatively high temperature and pressure of HIPping were preferred to obtain an as-HIPped superalloy FGH96 with diminished PPB precipitation and homogeneously refined grains.

Investigation of hot- iso-static press process for tungsten target samples

International Nuclear Information System (INIS)

Xu Yongli; Zhang Jinquan; Li Huaqing

2006-01-01

Zr and stainless steel (S.S.) were selected respectively as the cladding materials of W target. The e-beam weld was used to prepare the W-Zr and W-S.S. small samples for hot iso-static press (HIP) process. The technology parameters of HIP were investigated at 1200, 1300, 1400 degree C and 180 MPa, respectively. The micro-morphology of the interface, diffusion depths and composition as well as their micro-hardness were observed and determined. The bonding of W-Zr and W-S.S. is very well under the testing conditions. There is no any pore or micro-crack in the interface, and there is no grain growth of W below 1400 degree C either. The diffusion of Zr to W at the interface of W-Zr is preferred during HIP process, and the diffusion depths under testing conditions are 6-13 μm. The diffusion of W and Fe is considerable at the interface of W-S.S. Its depth is about 13 μm, and the diffusion of Cr and Ni is mall. The hardness at the interface of W-Zr and W-S.S. shows that a diffusion layer is present for both interface. A part of stainless steel cladding was melted after HIP contained the oxygen absorber Zr at 1300 degree C and 180 MPa. Therefore, 1200 degree C and 180 MPa is suitable for W-S.S. without Zr, but 1300 or 1400 degree C and 180 MPa is better for W-Zr. (authors)

First wall and shield components manufacturing by hot isostatic pressing

International Nuclear Information System (INIS)

Lind, Anders; Tegman, R.

1994-01-01

At a meeting in Garching in June 1994 Hot Isostatic Pressing (HIP) was presented as a possible route to manufacture ITER first wall and shield components. The main advantages of the HIP concept include excellent and uniform mechanical properties of the produced materials and joints, high reliability and robustness of the HIP process, double containment of coolant, good flexibility concerning general design as well as size and location for inner cooling tubes, low cost and short delivery times, and a good near net shape capability for components in size up to 15 tons. To assess the applicability of HIP for the manufacturing of ITER first wall and shield components, it was agreed * to choose possible production parameters based in the present know-how, * to produce a compound mock-up in one shot from available solid steel/powder copper/steel tubes to demonstrate the joinability of the materials, * to examine the produced mock-up/materials by multi array ultrasonic testing, limited mechanical testing, metallography, scanning electron microscopy and energy dispersive spectroscopy, and * to compile data on Type 316L steels produced by HIP. Preliminary results and the mock-up were presented at a meeting in Garching in mid July 1994. This study clearly shows the excellent joinability of a copper alloy (Cu-0.5%Zr) and stainless steels (Type 304, 316 L) by HIP at temperatures close to the melting temperature of copper, with only limited influence on the microstructures, which makes it possible to HIP the first wall and shield structure in one step. Excellent mechanical properties of the compound are obtained with the copper alloy and not the joint being the weakest part. 7 refs, 21 figs, 1 tab

Fabrication of Y-TZP For Dental Crowns Applications by Combining Slip Casting and Cold Isostatic Pressing

International Nuclear Information System (INIS)

Hao, C.C.; Andanastuti Muchtar; Che Husna Azhari; Masfueh Razali; Mohamed Aboras

2016-01-01

Yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) is a popular material for dental restoration because of its outstanding mechanical properties and biocompatibility. Cold isostatic pressing (CIP) and slip casting are among several consolidation methods for Y-TZP. These methods produce Y-TZP with high mechanical properties. This study aims to enhance the mechanical properties of Y-TZP by combining slip casting and CIP. Y-TZP samples were fabricated using CIP, slip casting, and their combination. Subsequently, the green bodies of the samples were sintered at 1600 degree Celcius. Their mechanical properties (density and hardness) were tested and their microstructures were scrutinized under a scanning electron microscope. Compared with the other two methods, the combined method significantly improved the mechanical properties of Y-TZP. In addition, the combined method also produced a compact and homogeneous microstructure. Therefore, the combination of slip casting and CIP is recommended in the production of Y-TZP with high mechanical properties for dental crown applications. (author)

The effect of pre-treatment parameters on the quality of glass-ceramic wasteforms for plutonium immobilisation, consolidated by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Thornber, Stephanie M.; Heath, Paul G. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Da Costa, Gabriel P. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Department of Chemical Engineering & Petroleum Engineering, Universidade Federal Fluminense, Rua Passo da Patria 156, CEP 24210-240, Niteroi, RJ (Brazil); Stennett, Martin C. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Hyatt, Neil C., E-mail: n.c.hyatt@sheffield.ac.uk [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom)

2017-03-15

Glass-ceramics with high glass fractions (70 wt%) were fabricated in stainless steel canisters by hot isostatic pressing (HIP), at laboratory scale. High (600 °C) and low (300 °C) temperature pre-treatments were investigated to reduce the canister evacuation time and to understand the effect on the phase assemblage and microstructure of the hot isostatically pressed product. Characterisation of the HIPed materials was performed using scanning electron microscopy (SEM), coupled with energy dispersive X-ray analysis (EDX) and powder X-ray diffraction (XRD). This analysis showed the microstructure and phase assemblage was independent of the variation in pre-treatment parameters. It was demonstrated that a high temperature pre-treatment of batch reagents, prior to the HIP cycle, is beneficial when using oxide precursors, in order to remove volatiles and achieve high quality dense materials. Sample throughput can be increased significantly by utilising a high temperature ex-situ calcination prior to the HIP cycle. Investigation of glass-ceramic wasteform processing utilising a glass frit precursor, produced a phase assemblage and microstructure comparable to that obtained using oxide precursors. The use of a glass frit precursor should allow optimised throughput of waste packages in a production facility, avoiding the need for a calcination pre-treatment required to remove volatiles from oxide precursors. - Highlights: • Optimisation of pre-treatment parameters for HIP glass-ceramics was investigated. • Entrained porosity was minimised by ex-situ bake-out of oxide precursors at 600 °C. • Phase assemblage and microstructure proved independent of bake-out parameters. • Use of glass-frit precursor further improved process s throughput and simplification.

Tensile ductility of an AlCoCrFeNi multi-phase high-entropy alloy through hot isostatic pressing (HIP) and homogenization

Energy Technology Data Exchange (ETDEWEB)

Tang, Zhi, E-mail: Zhi.Tang@alcoa.com [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Department of Materials Science and Engineering, Virginia Tech, Blacksburg, VA 24061 (United States); Senkov, Oleg N. [Air Force Research Laboratory, Materials and Manufacturing Directorate, Wright-Patterson Air Force Base, OH 45433 (United States); Parish, Chad M. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Zhang, Chuan; Zhang, Fan [CompuTherm LLC, 437 S. Yellowstone Dr., Suite 217, Madison, WI 53719 (United States); Santodonato, Louis J. [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Wang, Gongyao [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States); Zhao, Guangfeng; Yang, Fuqian [Department of Chemical and Materials Engineering, University of Kentucky, Lexington, KY 40506 (United States); Liaw, Peter K., E-mail: pliaw@utk.edu [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996 (United States)

2015-10-28

The microstructure and phase composition of an AlCoCrFeNi high-entropy alloy (HEA) were studied in as-cast (AlCoCrFeNi-AC, AC represents as-cast) and homogenized (AlCoCrFeNi-HP, HP signifies hot isostatic pressed and homogenized) conditions. The AlCoCrFeNi-AC ally has a dendritric structure in the consisting primarily of a nano-lamellar mixture of A2 (disordered body-centered-cubic (BCC)) and B2 (ordered BCC) phases, formed by an eutectic reaction. The homogenization heat treatment, consisting of hot isostatic pressed for 1 h at 1100 °C, 207 MPa and annealing at 1150 °C for 50 h, resulted in an increase in the volume fraction of the A1 phase and formation of a Sigma (σ) phase. Tensile properties in as-cast and homogenized conditions are reported at 700 °C. The ultimate tensile strength was virtually unaffected by heat treatment, and was 396±4 MPa at 700 °C. However, homogenization produced a noticeable increase in ductility. The AlCoCrFeNi-AC alloy showed a tensile elongation of only 1.0%, while after the heat-treatment, the elongation of AlCoCrFeNi-HP was 11.7%. Thermodynamic modeling of non-equilibrium and equilibrium phase diagrams for the AlCoCrFeNi HEA gave good agreement with the experimental observations of the phase contents in the AlCoCrFeNi-AC and AlCoCrFeNi-HP. The reasons for the improvement of ductility after the heat treatment and the crack initiation subjected to tensile loading were discussed.

The effect of pre-treatment parameters on the quality of glass-ceramic wasteforms for plutonium immobilisation, consolidated by hot isostatic pressing

International Nuclear Information System (INIS)

Thornber, Stephanie M.; Heath, Paul G.; Da Costa, Gabriel P.; Stennett, Martin C.; Hyatt, Neil C.

2017-01-01

Glass-ceramics with high glass fractions (70 wt%) were fabricated in stainless steel canisters by hot isostatic pressing (HIP), at laboratory scale. High (600 °C) and low (300 °C) temperature pre-treatments were investigated to reduce the canister evacuation time and to understand the effect on the phase assemblage and microstructure of the hot isostatically pressed product. Characterisation of the HIPed materials was performed using scanning electron microscopy (SEM), coupled with energy dispersive X-ray analysis (EDX) and powder X-ray diffraction (XRD). This analysis showed the microstructure and phase assemblage was independent of the variation in pre-treatment parameters. It was demonstrated that a high temperature pre-treatment of batch reagents, prior to the HIP cycle, is beneficial when using oxide precursors, in order to remove volatiles and achieve high quality dense materials. Sample throughput can be increased significantly by utilising a high temperature ex-situ calcination prior to the HIP cycle. Investigation of glass-ceramic wasteform processing utilising a glass frit precursor, produced a phase assemblage and microstructure comparable to that obtained using oxide precursors. The use of a glass frit precursor should allow optimised throughput of waste packages in a production facility, avoiding the need for a calcination pre-treatment required to remove volatiles from oxide precursors. - Highlights: • Optimisation of pre-treatment parameters for HIP glass-ceramics was investigated. • Entrained porosity was minimised by ex-situ bake-out of oxide precursors at 600 °C. • Phase assemblage and microstructure proved independent of bake-out parameters. • Use of glass-frit precursor further improved process s throughput and simplification.

Comparison between uniaxially and isostatically compacted bentonite

International Nuclear Information System (INIS)

Kalbantner, P.; Sjoeblom, R.; Boergesson, Lennart

2001-12-01

The purpose of the present report is to provide the Swedish Nuclear Fuel and Waste Management Company (SKB) with the knowledge base needed for their selection of reference method for manufacturing of bentonite blocks. The purpose is also to provide support for the direction of the further development work. Three types of blocks are compared in the present report: uniaxially compacted medium high blocks, isostatically compacted medium high blocks, isostatically compacted high blocks. The analyses is based on three process systems relating to the sequence of excavation of bentonite-transport-powder preparation-compaction-handling and emplacement of bentonite blocks. The need for further knowledge has been identified and documented in conjunction with these analyses. The comparison is primarily made with regard to the criteria safety/risk, quality/ technique and economy. It is carried out through identification of issues of significance and subsequent analysis and evaluation as well as more formally in a simplified AHP (AHP = Analytical Hierarchic Process). The result of the analyses is that the isostatic technique is applicable for the production of high as well as medium size blocks. The pressed blocks are assessed to fulfil the basic requirements with a very large margin. The result of the analyses is also that the uniaxial technique is applicable for the preparation of medium size blocks, which are assessed to fulfil the basic requirements with a large margin. The need for development and process control is assessed to be somewhat higher for the uniaxial technique. One example is the friction against the walls of the die during the compaction, including the significance of this friction for the development of stresses and discontinuities in the block. These results support a selection of the isostatic technique as the reference technique as it provides flexibility in the choice of block height. The uniaxial technique can form a second alternative if medium high

Effect of Fe on the phases and microstructure of TiC-Fe cermets by combustion synthesis/quasi-isostatic pressing

International Nuclear Information System (INIS)

Zhang Weifang; Zhang Xinghong; Wang Jianli; Hong Changqing

2004-01-01

Fully dense TiC-Fe cermets (x = 10, 20, 30, and 40 wt.%) were produced from Ti-C-Fe powder mixtures by combustion synthesis with quasi-isostatic pressing. The effect of Fe content on combustion temperature, combustion wave velocity, and final product density was investigated. The final product was characterized by XRD, SEM, and TEM. The combustion temperature and wave velocity decreased with increasing Fe content. Product density increased with increasing Fe content (96% at 30 wt.%). X-ray diffraction and transmission electron microscopy (TEM) revealed the final product to contain TiC, Fe phases, lath martensite, and Fe 2 Ti. The TiC particle size decreased with increasing Fe content. In addition, a low density of dislocations was observed in both the TiC particles and Fe binder, indicative of annealing and recrystallization, respectively

Experimental and Simulation Analysis of Hot Isostatic Pressing of Gas Atomized Stainless Steel 316L Powder Compacts

International Nuclear Information System (INIS)

Lin, Dongguo; Park, Seong Jin; Ha, Sangyul; Shin, Youngho; Park, Dong Yong; Chung, Sung Taek; Bollina, Ravi; See, Seongkyu

2016-01-01

In this work, both experimental and numerical studies were conducted to investigate the densification behavior of stainless steel 316L (STS 316L) powders during hot isostatic pressing (HIP), and to characterize the mechanical properties of HIPed specimens. The HIP experiments were conducted with gas atomized STS 316L powders with spherical particle shapes under controlled pressure and temperature conditions. The mechanical properties of HIPed samples were determined based on a series of tensile tests, and the results were compared to a reference STS 316L sample prepared by the conventional process, i.e., extrusion and annealing process. Corresponding microstructures before and after tensile tests were observed using scanning electron microscopy and their relationships to the mechanical properties were addressed. Furthermore, a finite element simulation based on the power-law creep model was carried out to predict the density distribution and overall shape change of the STS316L powder compact during HIP process, which agreed well with the experimental results.

Experimental and Simulation Analysis of Hot Isostatic Pressing of Gas Atomized Stainless Steel 316L Powder Compacts

Energy Technology Data Exchange (ETDEWEB)

Lin, Dongguo; Park, Seong Jin [Pohang University of Science and Technology, Pohang (Korea, Republic of); Ha, Sangyul [Samsung Electro-Mechanics, Suwon (Korea, Republic of); Shin, Youngho [Doosan Heavy Industries and Construction Co., Ltd., Changwon (Korea, Republic of); Park, Dong Yong [Korea Institute of Energy Research, Daejeon (Korea, Republic of); Chung, Sung Taek [CetaTech Inc., Sacheon (Korea, Republic of); Bollina, Ravi [Bahadurpally Jeedimetla, Hyderabad (India); See, Seongkyu [POSCO, Pohang (Korea, Republic of)

2016-10-15

In this work, both experimental and numerical studies were conducted to investigate the densification behavior of stainless steel 316L (STS 316L) powders during hot isostatic pressing (HIP), and to characterize the mechanical properties of HIPed specimens. The HIP experiments were conducted with gas atomized STS 316L powders with spherical particle shapes under controlled pressure and temperature conditions. The mechanical properties of HIPed samples were determined based on a series of tensile tests, and the results were compared to a reference STS 316L sample prepared by the conventional process, i.e., extrusion and annealing process. Corresponding microstructures before and after tensile tests were observed using scanning electron microscopy and their relationships to the mechanical properties were addressed. Furthermore, a finite element simulation based on the power-law creep model was carried out to predict the density distribution and overall shape change of the STS316L powder compact during HIP process, which agreed well with the experimental results.

Microstructure and thermal conductivity of Mo-TiC cermets processed by hot isostatic pressing

International Nuclear Information System (INIS)

Le Flem, Marion; Allemand, Alexandre; Urvoy, Stephane; Cedat, Denis; Rey, Colette

2008-01-01

In the scope of refractory material development for structural applications in the core of future nuclear reactors (gas fast reactors working between 500 o C and at least 800 o C in nominal conditions and up to 1650 o C in accidental scenarios), five Mo-TiC cermets, and single-phase TiC and Mo, were processed by hot isostatic pressing. Starting TiC volume contents were 0%, 12.5%, 25%, 37.5%, 50%, 75% and 100%. First, high dense specimens were characterized in terms of microstructure, composition and phase volume fractions. Cermets exhibited two phases in agreement with phase diagram previsions (Mo-TiC 1-2at.% and TiC-Mo 10-15at.% ), and a residual non-reacted TiC-rich phase (TiC-Mo 1at.% ). Second, heat capacity and thermal diffusivity were measured up to 1000 o C which allowed to evaluate the thermal conductivity of each cermet: this lays between TiC conductivity (12-18 W/m K) and Mo conductivity (95-125 W/m K), thermal properties continuously decreasing with starting TiC content. An analytical approach based on the volume fraction and properties of each constituent allowed to highlight the existence of thermal resistance at the interphases at low temperature

Pressure slip casting and cold isostatic pressing of aluminum titanate green ceramics: A comparative evaluation

Directory of Open Access Journals (Sweden)

Ramanathan Papitha

2013-12-01

Full Text Available Aluminum titanate (Al2TiO5 green bodies were prepared from mixture of titania and alumina powders with different particle sizes by conventional slip casting (CSC, pressure slip casting (PSC and cold isostatic pressing (CIP. Precursor-powder mixtures were evaluated with respect to the powder properties, flow behaviours and shaping parameters. Green densities were measured and correlated with the fractographs. A substantial increase in green densities up to 60 %TD (theoretical density of 4.02 g/cm3, calculated based on rule of mixtures is observed with the application of 2–3 MPa pressure with PSC. While particle size distribution and solid loading are the most influential parameters in the case of CSC, with PSC pressure also plays a key role in achieving the higher green densities. Being a dry process, high pressure of > 100 MPa for CIP is essential to achieve densities in the range of 60–65 %TD. Slip pressurization under PSC conditions facilitate the rearrangement of particles through rolling, twisting and interlocking unlike CIP processing where pressure is needed to overcome the inter-particle friction.

Influence of surface treatment of yttria-stabilized tetragonal zirconia polycrystal with hot isostatic pressing on cyclic fatigue strength.

Science.gov (United States)

Iijima, Toshihiko; Homma, Shinya; Sekine, Hideshi; Sasaki, Hodaka; Yajima, Yasutomo; Yoshinari, Masao

2013-01-01

Hot isostatic pressing processed yttria-stabilized tetragonal zirconia polycrystal (HIP Y-TZP) has the potential for application to implants due to its high mechanical performance. The aim of this study was to investigate the influence of surface treatment of HIP Y-TZP on cyclic fatigue strength. HIP Y-TZP specimens were subjected to different surface treatments. Biaxial flexural strength was determined by both static and cyclic fatigue testing. In the cyclic fatigue test, the load was applied at a frequency of 10 Hz for 10(6) cycles in distilled water at 37°C. The surface morphology, roughness, and crystal phase of the surfaces were also evaluated. The cyclic fatigue strength (888 MPa) of HIP Y-TZP with sandblasting and acid-etching was more than twice that of Y-TZP as specified in ISO 13356 for surgical implants (320 MPa), indicating the clinical potential of this material.

Effect of Hot-isostatic Pressing on Microstructure and Mechanical Properties of Second Generation Single Crystal Superalloy DD6

Directory of Open Access Journals (Sweden)

GUO Hui-ming

2016-10-01

Full Text Available Effects of the hot-isostatic pressing (HIP temperature (1280,1300,1320℃ on microstructures and mechanical properties of a second generation single crystal superalloy DD6 were investigated. The results show that the HIP treatment significantly decrease the cast porosity number of DD6 compared with standard treated specimens. Especially, the cast porosity volume fraction is deceased from 0.31% to 0.04% after the HIP treatment of 1300℃/100MPa, 4h. The cast eutectic volume fractions are remarkably reduced with increasing HIP temperature. The HIP treatments nearly unchanged the creep lives, While they greatly promote the low cycle fatigue lives. The elimination of cast microspores using the HIP treatment of 1300℃/100MPa, 4h result in the inhibition of crack initiation during fatigue and improve the low cycle fatigue lives one order of magnitude larger than that after standard heat treatment.

Preliminary Study on Hot Isostatic Pressing Diffusion Bonding for CLAM Steel

International Nuclear Information System (INIS)

Chunjing Li; Qunying Huang; Yican Wu

2006-01-01

China Low Activation Martensitic (CLAM) steel is being developed in ASIPP (Institute of Plasma Physics, Chinese Academy of Sciences) since three years ago. CLAM is selected as the major candidate structure materials for the FDS series design of fusion reactors and for China liquid metal LiPb Test Blanket Module (TBM) for ITER i.e. DFLL-TBM, which are being carried out in ASIPP. Since the hot isostatic pressing (HIP) bonding technique is one of the main candidate bonding techniques for manufacturing of the first wall of a fusion reactor, research of the HIP technique on CLAM/CLAM is greatly needed. Preliminary HIP diffusion bonding experiments on CLAM steel have been performed. A few machining approaches such as dry-milling, turnery and grounding etc. were used to prepare the sample surfaces and then they were degreased with a mixture of alcohol, ether and acetone in an ultrasonic bath. The samples were joined by HIP diffusion bonding with the compression pressure of 150 MPa and the holding time of 2 ∼ 3 hours under different temperatures between 950 deg. and 1100 deg.. Different seal techniques of the capsules were studied as well. Then appropriate post heat treatment was done. Tests on mechanical properties of the joints such as tensile strength and impact toughness have been performed. The preliminary results show that the tensile properties are roughly the same as those of the base material. The absorbed energy of the joints at present is a little low and further research is needed to increase it. Microstructure of the joints was studied by optical microscope, SEM and TEM. Compositions of the defects on the joining line were analyzed by EDS. Through analysis of the results, optimized parameters for HIP are given. (author)

A novel Fe–Cr–Nb matrix composite containing the TiB_2 neutron absorber synthesized by mechanical alloying and final hot isostatic pressing (HIP) in the Ti-tubing

International Nuclear Information System (INIS)

Litwa, Przemysław; Perkowski, Krzysztof; Zasada, Dariusz; Kobus, Izabela; Konopka, Gustaw; Czujko, Tomasz; Varin, Robert A.

2016-01-01

The Fe–Cr–Ti-Nb elemental powders were mechanically alloyed/ball milled with TiB_2 and a small quantity of Y_2O_3 ceramic to synthesize a novel Fe-based alloy-ceramic powder composite that could be processed by hot isostatic pressing (HIP) for a perceived potential application as a neutron absorber in nuclear reactors. After ball milling for the 30–80 h duration relatively uniform powders with micrometric sizes were produced. With increasing milling time a fraction of TiB_2 particles became covered with the much softer Fe-based alloy which resulted in the formation of a characteristic “core-mantel” structure. For the final HIP-ing process the mechanically alloyed powders were initially uniaxially pressed into rod-shaped compacts and then cold isostatically pressed (CIP-ed). Subsequently, the rod-shaped compacts were placed in the Ti-tubing and subjected to hot isostatic pressing (HIP) at 1150 °C/200 MPa pressure. The HIP-ing process resulted in the formation of the near-Ti and intermediate diffusional layers in the microstructure of HIP-ed samples which formed in accord with the Fe-Ti binary phase diagram. Those layers contain the phases such as α-Ti (HCP), the FeTi intermetallic and their hypo-eutectoid mixtures. In addition, needle-like particles were formed in both layers in accord with the Ti-B binary phase diagram. Nanohardness testing, using a Berkovich type diamond tip, shows that the nanohardness in the intermediate layer areas, corresponding to the composition of the hypo-eutectoid mixture of Ti-FeTi, equals 980.0 (±27.1) HV and correspondingly 1176.9 (±47.6) HV for the FeTi phase. The nanohardness in the sample's center in the areas with the fine mixture of Fe-based alloy and small TiB_2 particles equals 1048.3 (±201.8) HV. The average microhardness of samples HIP-ed from powders milled for 30 and 80 h is 588 HV and 733 HV, respectively. - Highlights: • A Fe–Cr–Nb-based composite with TiB_2 neutron absorbing ceramic was mechanically

Atlas of hot isostatic beryllium powder pressing diagrams

International Nuclear Information System (INIS)

Stoev, P.I.; Papirov, I.I.; Tikhinskij, G.F.; Vasil'ev, A.A.

1995-01-01

Diagrams of hot isotopic pressing (HIP) of beryllium powder with different grain size in a wide range of pressing parameters are built by mathematical modeling methods. The HIP diagrams presented are divided into 3 groups: parametric dependencies D=f(P,T); technological HIP diagrams; compacting mechanisms. The created data bank permits to optimise beryllium powder HIP with changing parameters. 4 refs., 23 figs

Effect of heat treatment and hot isostatic pressing on the microstructure and mechanical properties of Inconel 625 alloy processed by laser powder bed fusion

Energy Technology Data Exchange (ETDEWEB)

Kreitcberg, Alena, E-mail: alena.kreitcberg.1@ens.etsmtl.ca [École de technologie supérieure, 110 Notre-Dame Street West, Montreal, Quebec H3C 1K3 Canada (Canada); Brailovski, Vladimir, E-mail: vladimir.brailovski@etsmtl.ca [École de technologie supérieure, 110 Notre-Dame Street West, Montreal, Quebec H3C 1K3 Canada (Canada); Turenne, Sylvain, E-mail: sylvain.turenne@polymtl.ca [École Polytechnique de Montréal, 2900 boul. Édouard-Montpetit, Montreal, Quebec H3T 1J4 Canada (Canada)

2017-03-24

The effect of different heat treatments and hot isostatic pressing on the microstructure and mechanical properties of laser powder bed fusion IN625 alloy was studied. The heat treatments were: stress relief annealing, recrystallization annealing and low-temperature solution treatment. The resulting microstructure and crystallographic textures were studied using optical and scanning electron microscopy. The mechanical properties of the as-built and post-treated IN625 alloy were obtained after tensile testing at room temperature and at 760 °C (1400 °F), and compared to those of an annealed wrought alloy of the same composition.

Formation of ultra-fine grained TiC-dispersed SUS316L by ball-milling and their consolidation by hot isostatic pressing

International Nuclear Information System (INIS)

Zheng, Yongjia; Yamasaki, Tohru; Fukami, Takeshi; Mitamura, Tohru; Terasawa, Mititaka

2003-01-01

In order to overcome the irradiation embrittlement in austenitic stainless steels, ultra-fine grained SUS316L steels with very fine TiC particles have been developed. The SUS316-TiC nanocomposite powders having 1.0 to 2.0 mass%TiC were prepared by ball-milling SUS316-TiC powder mixtures for 125h in an argon gas atmosphere. The milled powders were consolidated by hot isostatic pressing (HIP) under a pressure of 200 MPa at temperature between 700-1000degC, and the bulk materials with crystallite size ranging between 100-400 nm have been produced. The possibility of using fine-grained TiC particles for pinning grain boundaries and thereby to maintain the ultra-fine grained structures has been discussed. (author)

Tensile Fracture Behavior of 316L Austenitic Stainless Steel Manufactured by Hot Isostatic Pressing

Science.gov (United States)

Cooper, A. J.; Brayshaw, W. J.; Sherry, A. H.

2018-02-01

Herein we investigate how the oxygen content in hot isostatically pressed (HIP'd) 316L stainless steel affects the mechanical properties and tensile fracture behavior. This work follows on from previous studies, which aimed to understand the effect of oxygen content on the Charpy impact toughness of HIP'd steel. We expand on the work by performing room-temperature tensile testing on different heats of 316L stainless steel, which contain different levels of interstitial elements (carbon and nitrogen) as well as oxygen in the bulk material. Throughout the work we repeat the experiments on conventionally forged 316L steel as a reference material. The analysis of the work indicates that oxygen does not contribute to a measureable solution strengthening mechanism, as is the case with carbon and nitrogen in austenitic stainless steels (Werner in Mater Sci Eng A 101:93-98, 1988). Neither does oxygen, in the form of oxide inclusions, contribute to precipitation hardening due to the size and spacing of particles. However, the oxide particles do influence fracture behavior; fractography of the failed tension test specimens indicates that the average ductile dimple size is related to the oxygen content in the bulk material, the results of which support an on-going hypothesis relating oxygen content in HIP'd steels to their fracture mechanisms by providing additional sites for the initiation of ductile damage in the form of voids.

Justification and manufacturing quality assurance for the use of hot Isostatically pressed, reactor coolant system components in PWR plant

International Nuclear Information System (INIS)

Sulley, J. L.; Hookham, I. D.

2008-01-01

This paper presents an overview of the work undertaken by Rolls-Royce to introduce Hot Isostatically Pressed (HIP) components into Pressurised Water Reactor plant. It presents the work from a design justification and manufacturing quality assurance perspective, rather than from a pure metallurgical perspective, although some metallurgical and mechanical property comparisons with the traditional forged material are presented. Although the HIP process is not new, it was new in its application to Rolls-Royce designed nuclear reactor plant. In order to satisfy the regulatory requirement of 'Proven Engineering Practices' with regard to the introduction of new material processes, and to provide a robust manufacturing substantiation leg of a multi-legged safety case, Rolls-Royce has implemented an evolving, staged approach, starting with HIP bonding of solid valve seats into small bore valve pressure boundaries. This was followed by powder HIP consolidation of leak-limited, thin-walled toroids, and has culminated in the powder HIP consolidation of components, such as steam generator headers, large bore valves and pipe sections. The paper provides an overview of each of these stages and the approach taken with respect to justification. The paper describes the benefits that Rolls-Royce has realised so far through the introduction of HIPed components, and improvements planned for the future. Structural integrity benefits are described, such as improved grain structure, mechanical properties, and ultrasonic inspection. Project-based benefits are also described, such as provision of an alternative strategic sourcing route, cost and lead-time reduction. A full description is provided of key quality assurance steps applied to the process to ensure a high quality product is delivered commensurate with a high integrity nuclear application. 2008 Rolls-Royce plc. (authors)

Influence of Powder Surface Contamination in the Ni-Based Superalloy Alloy718 Fabricated by Selective Laser Melting and Hot Isostatic Pressing

Directory of Open Access Journals (Sweden)

Yen-Ling Kuo

2017-09-01

Full Text Available The aim of this study was to gain a deep understanding of the microstructure-mechanical relationship between solid-state sintering and full-melting processes. The IN718 superalloy was fabricated by hot isostatic pressing (HIP and selective laser melting (SLM. Continuous precipitates were clearly localized along the prior particle boundary (PPB in the HIP materials, while SLM materials showed a microstructure free of PPB. The mechanical properties of specimens that underwent SLM + solution treatment and aging were comparable to those of conventional wrought specimens both at room temperature and 650 °C. However, a drop was observed in the ductility of HIP material at 650 °C. The brittle particles along the PPB were found to affect the HIP materials’ creep life and ductility during solid-state sintering.

Isostatic Model and Isostatic Gravity Anomalies of the Arabian Plate and Surroundings

Science.gov (United States)

Kaban, Mikhail K.; El Khrepy, Sami; Al-Arifi, Nassir

2016-04-01

The isostatic modeling represents one of the most useful "geological" reduction methods of the gravity field. With the isostatic correction, it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. Although there exist several isostatic compensation schemes, it is usually supposed that a choice of the model is not an important factor to first order, since the total weight of compensating masses remains the same. We compare two alternative models for the Arabian plate and surrounding area. The Airy model gives very significant regional isostatic anomalies, which cannot be explained by the upper crust structure or disturbances of the isostatic equilibrium. Also, the predicted "isostatic" Moho is very different from existing seismic observations. The second isostatic model includes the Moho, which is based on seismic determinations. Additional compensation is provided by density variations within the lithosphere (chiefly in the upper mantle). According to this model, the upper mantle under the Arabian Shield is less dense than under the Platform. In the Arabian platform, the maximum density coincides with the Rub' al Khali, one of the richest oil basin in the world. This finding agrees with previous studies, showing that such basins are often underlain by dense mantle, possibly related to an eclogite layer that has caused their subsidence. The mantle density variations might be also a result of variations of the lithosphere thickness. With the combined isostatic model, it is possible to minimize regional anomalies over the Arabian plate. The residual local anomalies correspond well to tectonic structure of the plate. Still very significant anomalies, showing isostatic disturbances of the lithosphere, are associated with the Zagros fold belt, the collision zone of the Arabian and Eurasian plates.

Role of aging time on the magnetic properties of Sm2Co17 permanent magnets processed through cold isostatic pressing

Science.gov (United States)

Ramudu, M.; Rajkumar, D. M.

2018-04-01

The effect of aging time on the magnetic properties of Sm2Co17 permanent magnets processed through a novel method of cold isostatic pressing was investigated. Sintered Sm2Co17 samples were subjected to different aging times in the range of 10-30 h and their respective microstructures were correlated with the magnetic properties obtained. The values of remanant magnetization (Br) were observed to be constant in samples aged from 10-20 h beyond which a gradual decrease in Br values was observed. The values of coercivity (Hc) displayed a sharp increase in samples aged from 10 to 20 h beyond which the coercivity values showed marginal improvement. Hence a good combination of magnetic properties could be achieved in samples aged for 20 h. A maximum energy product of 27 MGOe was achieved in the 20 h aged sample processed through a novel route.

A study on improving mechanical properties of porous HA tissue engineering scaffolds by hot isostatic pressing

International Nuclear Information System (INIS)

Zhao Jing; Xiao Suguang; Lu Xiong; Wang Jianxin; Weng Jie

2006-01-01

Various interconnected porous hydroxyapatite (HA) ceramic scaffolds are universally used to induct the tissue growth for bone repair and replacement, and serve to support the adhesion, transfer, proliferation and differentiation of cells. Impregnation of polyurethane sponges with a ceramic slurry is adopted to produce highly porous HA ceramic scaffolds with a 3D interconnected structure. However, high porosity always accompanies a decrease in the strength of the HA ceramic scaffolds. Therefore, it is significant to improve the strength of the HA ceramic scaffolds with highly interconnected porosity so that they are more suitable in clinical applications. In this work, highly porous HA ceramic scaffolds are first produced by the polymer impregnation approach, and subsequently further sintered by hot isostatic pressing (HIP). The phase composition, macro- and micro-porous structure, sintering and mechanical properties of the porous HA scaffolds are investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), nanoindentation analysis and compressive test. The experimental results show that the nanohardness and compressive strength of HIP-sintered porous HA ceramics are higher than those of commonly sintered HA scaffolds. The HIP technique can effectively improve the sintering property and densification of porous HA ceramic scaffolds, so inducing an increase in the compression strength

A novel Fe–Cr–Nb matrix composite containing the TiB{sub 2} neutron absorber synthesized by mechanical alloying and final hot isostatic pressing (HIP) in the Ti-tubing

Energy Technology Data Exchange (ETDEWEB)

Litwa, Przemysław [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Perkowski, Krzysztof [Department of Nanotechnology, Institute of Ceramics and Building Materials, Postępu 9, 02-676 Warsaw (Poland); Zasada, Dariusz [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Kobus, Izabela; Konopka, Gustaw [Department of Nanotechnology, Institute of Ceramics and Building Materials, Postępu 9, 02-676 Warsaw (Poland); Czujko, Tomasz [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Varin, Robert A., E-mail: robert.varin@uwaterloo.ca [Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Ave., Waterloo, ON N2L 3G1 (Canada)

2016-07-25

The Fe–Cr–Ti-Nb elemental powders were mechanically alloyed/ball milled with TiB{sub 2} and a small quantity of Y{sub 2}O{sub 3} ceramic to synthesize a novel Fe-based alloy-ceramic powder composite that could be processed by hot isostatic pressing (HIP) for a perceived potential application as a neutron absorber in nuclear reactors. After ball milling for the 30–80 h duration relatively uniform powders with micrometric sizes were produced. With increasing milling time a fraction of TiB{sub 2} particles became covered with the much softer Fe-based alloy which resulted in the formation of a characteristic “core-mantel” structure. For the final HIP-ing process the mechanically alloyed powders were initially uniaxially pressed into rod-shaped compacts and then cold isostatically pressed (CIP-ed). Subsequently, the rod-shaped compacts were placed in the Ti-tubing and subjected to hot isostatic pressing (HIP) at 1150 °C/200 MPa pressure. The HIP-ing process resulted in the formation of the near-Ti and intermediate diffusional layers in the microstructure of HIP-ed samples which formed in accord with the Fe-Ti binary phase diagram. Those layers contain the phases such as α-Ti (HCP), the FeTi intermetallic and their hypo-eutectoid mixtures. In addition, needle-like particles were formed in both layers in accord with the Ti-B binary phase diagram. Nanohardness testing, using a Berkovich type diamond tip, shows that the nanohardness in the intermediate layer areas, corresponding to the composition of the hypo-eutectoid mixture of Ti-FeTi, equals 980.0 (±27.1) HV and correspondingly 1176.9 (±47.6) HV for the FeTi phase. The nanohardness in the sample's center in the areas with the fine mixture of Fe-based alloy and small TiB{sub 2} particles equals 1048.3 (±201.8) HV. The average microhardness of samples HIP-ed from powders milled for 30 and 80 h is 588 HV and 733 HV, respectively. - Highlights: • A Fe–Cr–Nb-based composite with TiB{sub 2} neutron

Void formation in ODS EUROFER produced by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Ortega, Y.; Monge, M.A.; Munoz, A.; Leguey, T.; Pareja, R. [Madrid Univ. Carlos-3, Dept. de Fisica (Spain); Castro, V. de [Oxford Univ., Dept. of Materials (United Kingdom)

2007-07-01

Full text of publication follows: An obstacle in the development of oxide dispersion strengthened (ODS) steels for structural applications in fusion reactors is the toughness lack of the material produced by powder metallurgy and consolidated by hot isostatic pressing (HIP). In particular, ODS EUROFER steel with Y{sub 2}O{sub 3} particles appears to exhibit poor impact properties. To asses the capabilities of this material, it is necessary elucidate if its failure is an inherent characteristic of the production process that can not be mitigated by normalizing and tempering treatments. In order to investigate this particular point, the evolution of the structural defects retained in the ODS material during isochronal annealing has been probed by positron annihilation spectroscopy. The present study has been performed on bail milled EUROFER powders consolidated by HIP, containing 0.25 wt % Y{sub 2}O{sub 3} and without Y{sub 2}O{sub 3}. For comparison, un-milled EUROFER powder consolidated under identical conditions, and as-received EUROFER97 plate produced by Boehler AG have been also investigated. Samples from these four materials were isochronally annealed for 90 min up to 1323 K. Materials produced from milled powders had a longer positron lifetime than the one produced from un-milled powder or the EUROFER plate. In the material containing Y{sub 2}O{sub 3}, i.e. in ODS EUROFER, annealing above 723 K produced a continuous increase in the mean positron lifetime <{tau}> up to reach a maximum value of 208 ps after annealing at 1223 K. A similar annealing behavior was observed for Y{sub 2}O{sub 3}-free milled EUROFER (milled EUROFER), but the <{tau}> value steeply changed from {approx}160 ps at 823 K to {approx}200 ps after annealing at 1023 K. Subsequent anneals above this temperature produced meaningless changes in <{tau}>. The <{tau}> increase in milled EUROFER was accompanied by the intensity increase of a lifetime component of {approx}360 ps that is characteristic

Isostatic Model and Isostatic Gravity Anomalies of the Arabian Plate and Surroundings

OpenAIRE

M. K. Kaban; Sami El Khrepy; Nassir Al-Arifi

2016-01-01

The isostatic modeling represents one of the most useful ‘‘geological’’ reduction methods of the gravity field. With the isostatic correction, it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. Although there exist several isostatic compensation schemes, it is usually supposed that a choice of the model is not an important factor to first order, since the total weight of compensating m...

Effects of long-time elevated temperature exposures on hot-isostatically-pressed power-metallurgy Udimet 700 alloys with reduced cobalt contents

Science.gov (United States)

Hart, F. H.

1984-01-01

Because almost the entire U.S. consumption of cobalt depends on imports, this metal has been designated "strategic'. The role and effectiveness of cobalt is being evaluated in commercial nickel-base superalloys. Udiment 700 type alloys in which the cobalt content was reduced from the normal 17% down to 12.7%, 8.5%, 4.3%, and 0% were prepared by standard powder metallurgy techniques and hot isostatically pressed into billets. Mechanical testing and microstructural investigations were performed. The mechanical properties of alloys with reduced cobalt contents which were heat-treated identically were equal or better than those of the standard alloy, except that creep rates tended to increase as cobalt was reduced. The effects of long time exposures at 760 C on mechanical properties and at 760 C and 845 C on microstructures were determined. Decreased tensile properties and shorter rupture lives with increased creep rates were observed in alloy modifications. The exposures caused gamma prime particle coarsening and formation of sigma phase in the alloys with higher cobalt contents. Exposure at 845 C also reduced the amount of MC carbides.

Microstructure and properties of diffusion bonded Ti-6Al-4V parts using brazing-assisted hot isostatic pressing

International Nuclear Information System (INIS)

Wu, Z.; Mei, J.; Voice, W.; Beech, Steve; Wu, X.

2011-01-01

Highlights: → A low cost method of diffusion bonding has been developed for complex-shaped components of Ti6Al4V. → Vacuum brazing has been used to seal the periphery to allow encapsulation-free HIPping. → The tensile properties of the bonds are comparable with those of the bulk material, but the fatigue life was slightly reduced. - Abstract: Ti-6Al-4V couples have been diffusion bonded by hot isostatic pressing (HIPping) after vacuum brazing was used to seal the periphery of the bonding samples so that no encapsulation was required during HIPping. Analytical scanning electron microscopy was used to assess the microstructure of the HIPped interface and tensile and fatigue properties of bonded samples were compared with those of the bulk starting material. The tensile properties of the bonds were shown to be comparable with those of the bulk material, but the fatigue life was slightly downgraded. The fatigue fractures were initiated by inclusions on the bonding interface, caused by contamination before bonding, but the fatigue cracks did not propagate along the bonding interface indicating a strong bond. It is concluded that this technique of vacuum brazing plus HIPping could be used for encapsulation-free HIPping to produce complex-shaped components.

Hot-isostatic pressing (HIP). Pt. 2

International Nuclear Information System (INIS)

Bayer, E.; Moser, G.; Seilstorfer, H.

1981-01-01

After the description of the microstructure and strengthening mechanism of nickel- and cobalt-base superalloys, claims for the production of suitable powders for the HIP-technology are pointed out and methods to its realization are discussed. Taking the manufacture of turbine discs (ultrasonic form) as an example the possibilities of the near-net-shape-technology are shown. Investigations on mechanical properties and on microstructures are carried out to determine the effect of HIP-process-parameters on these features. (orig.) [de

Isostatic models and isostatic gravity anomalies of the Arabian plate and surroundings

Science.gov (United States)

Kaban, Mikhail K.; El Khrepy, Sami; Al-Arifi, Nassir

2015-04-01

Isostaic anomalies represent one of the most useful "geological" reduction of the gravity field. With the isostatic correction it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. This correction is based on the fact that a major part of the near-surface load is compensated by variations of the lithosphere boundaries (chiefly the Moho and LAB) and by density variations within the crust and upper mantle. It is usually supposed that it is less important to a first order, what is the actual compensation model when reducing the effect of compensating masses, since their total weight is exactly opposite to the near-surface load. We compare several compensating models for the Arabian plate and surrounding area. The Airy model gives very significant regional isostatic anomalies, which can not be explained by the upper crust structure or disturbances of the isostatic equilibrium. Also the predicted "isostatic" Moho is very different from the existing observations. The second group of the isostatic models includes the Moho, which is based on existing seismic determinations. Additional compensation is provided by density variations within the lithosphere (chiefly in the upper mantle). In this way we minimize regional anomalies over the Arabian plate. The residual local anomalies well correspond to tectonic structure of the plate. Still very significant anomalies are associated with the Zagros fold belt, the collision zone of the Arabian and Eurasian plates.

Production of an impermeable composite of irradiated graphite and glass by hot isostatic pressing as a long term leach resistant waste form

International Nuclear Information System (INIS)

Fachinger, Johannes; Muller, Walter; Marsat, Eric; Grosse, Karl-Heinz; Seemann, Richard; Scales, Charlie; Easton, Michael Mark; Anthony Banford

2013-01-01

negligible porosity and a water impermeable structure. Structural analysis shows that the glass in the composite has replaced the pores in the graphite structure. The typical pore volume of a graphite material is in the range of 20 vol.%. Therefore no volume increase will occur in comparison with the former graphite material. This IGM material will allow the encapsulation of graphite with package densities larger than 1.5 ton per cubic meter. Therefore a huge volume saving can be achieved by such an alternative encapsulation method. Disposal performance is also enhanced since little or no leaching of radionuclides is observed due to the impermeability of the material NNL and FNAG have proved that IGM can be produced by hot isostatic pressing (HIP) which has several advantages for radioactive materials over the HVP process. - The sealed HIP container avoids the release of any radionuclides. - The outside of the waste package is not contaminated. - The HIP process time is shorter than the HVP process time. The isostatic press avoids anisotropic density distributions. - Simple filling of the HIP container has advantages over the filling of an axial die. (authors)

Production of an impermeable composite of irradiated graphite and glass by hot isostatic pressing as a long term leach resistant waste form

Energy Technology Data Exchange (ETDEWEB)

Fachinger, Johannes; Muller, Walter [FNAG ZU Hanau, Hanau (Germany); Marsat, Eric [FNAG SAS Le Pont de Claix (France); Grosse, Karl-Heinz; Seemann, Richard [ALD Hanau (Germany); Scales, Charlie; Easton, Michael Mark [NNL, Workington (United Kingdom); Anthony Banford [NNL, Warrington (United Kingdom); University of Manchester, Manchester (United Kingdom)

2013-07-01

negligible porosity and a water impermeable structure. Structural analysis shows that the glass in the composite has replaced the pores in the graphite structure. The typical pore volume of a graphite material is in the range of 20 vol.%. Therefore no volume increase will occur in comparison with the former graphite material. This IGM material will allow the encapsulation of graphite with package densities larger than 1.5 ton per cubic meter. Therefore a huge volume saving can be achieved by such an alternative encapsulation method. Disposal performance is also enhanced since little or no leaching of radionuclides is observed due to the impermeability of the material NNL and FNAG have proved that IGM can be produced by hot isostatic pressing (HIP) which has several advantages for radioactive materials over the HVP process. - The sealed HIP container avoids the release of any radionuclides. - The outside of the waste package is not contaminated. - The HIP process time is shorter than the HVP process time. The isostatic press avoids anisotropic density distributions. - Simple filling of the HIP container has advantages over the filling of an axial die. (authors)

Theoretical and technical fundamentals of pressing porous powder articles of the complex shape

International Nuclear Information System (INIS)

Reut, O.; Piatsiushyk, Y.; Makarchuk, D.; Yakubouski, A.

2001-01-01

Intensification of technological processes, limited by the square of the surface of an active element porous powder field, is possible at the expense of magnification of the square of the surface of the latter by its addition. Thus the overall dimensions of such skew field are preserved. The analytical dependence of the factor of magnification of the surface K on geometrical parameters of a powder article of the complex shape is obtained. The optimization of these parameters in view of technological limitations for the maximization of K is carried out. The technique of calculating of the intense - deformed state of the powder skew field of the complex geometrical shape in the isostatic pressing is developed. The basic correlation permitting to calculate strain and deformation fields when pressing are gained. The technique of dry isostatic pressing of the article of the complex shape and the corresponding deforming instrument are developed. (author)

Enhancement in the microstructure and neutron shielding efficiency of sandwich type of 6061Al–B4C composite material via hot isostatic pressing

International Nuclear Information System (INIS)

Park, Jin-Ju; Hong, Sung-Mo; Lee, Min-Ku; Rhee, Chang-Kyu; Rhee, Won-Hyuk

2015-01-01

Highlights: • 6061Al–B 4 C neutron shielding composites are fabricated by sintering and HIP. • HIP process improves the wettability of B 4 C particles into 6061Al matrix. • Neutron attenuation performance can be enhanced by application of HIP process. - Abstract: Sandwich type of 6061Al–B 4 C composite plates, which are used as a thermal neutron absorber for spent nuclear fuel pool storage rack, were fabricated using two different consolidation ways as sintering and hot isostatic pressing (HIP) processes and their thermal neutron shielding efficiency was investigated as a function of B 4 C concentration ranging from 0 to 40 wt.%. For this purpose, two respective inner core compaction parts of sintered and HIPped neutron absorbing composite materials were first produced and then cladded them between two outer plates by HIP process. The application of HIP process provided not only a lead of excellent interfacial adhesion due to the improved wettability but also an enhancement of thermal neutron shielding efficiency owing to the more uniform dispersion of B 4 C particles

Development of manufacturing technology of radial plate in superconducting coil for fusion reactor by diffusion bonding by Hot Isostatic Pressing (HIP)

International Nuclear Information System (INIS)

Takano, Katsutoshi; Koizumi, Norikiyo; Masuo, Hiroshi; Natsume, Yoshihisa

2014-01-01

The radial plates (RPs), which is used in Toroidal field (TF) coil in ITER, are quite large, such as 13 m tall and 9 m wide, but thin, such as 10 cm thick, and are made of stainless steel. Even though they are very large structures, they require very high manufacturing tolerances and high mechanical strength at 4 K. The similar requirements will be required in the next generation fusion reactor. Therefore, the authors intend to develop efficient manufacturing methods in parallel with ITER TF coil RP manufacture. The authors therefore performed trial manufacture of the RP segments using a diffusion bonding method, namely Hot Isostatic Pressing (HIP). As a result of trials, it was clarified that even when HIPping is applied, the mechanical characteristic of base metal is not deteriorated. The machining period can be reduced by about 1/3 compared with the traditional manufacturing method. On the other hand, mechanical strength at 4 K is degraded due to weak bonding, that is no grain growth through joint, by HIPping. However, additional test indicates promising possibility of much better joint by higher temperature and joint surface treated HIPpings. These results justified that RP segment manufacturing is not only possible, but it is a technically valid manufacturing method that satisfies all requirements. (author)

Comparison of structure, morphology, and leach characteristics of multi-phase ceramics produced via melt processing and hot isostatic pressing

Science.gov (United States)

Dandeneau, Christopher S.; Hong, Tao; Brinkman, Kyle S.; Vance, Eric R.; Amoroso, Jake W.

2018-04-01

Melt processing of multi-phase ceramic waste forms offers potential advantages over traditional solid-state synthesis methods given both the prevalence of melters currently in use and the ability to reduce the possibility of airborne radionuclide contamination. In this work, multi-phase ceramics with a targeted hollandite composition of Ba1.0Cs0.3Cr1.0Al0.3Fe1.0Ti5.7O16 were fabricated by melt processing at 1675 °C and hot isostatic pressing (HIP) at 1250 and 1300 °C. X-ray diffraction analysis (XRD) confirmed hollandite as the major phase in all specimens. Zirconolite/pyrochlore peaks and weaker perovskite reflections were observed after melt processing, while HIP samples displayed prominent perovskite peaks and low-intensity zirconolite reflections. Melt processing produced specimens with large (>50 μm) well-defined hollandite grains, while HIP yielded samples with a more fine-grained morphology. Elemental analysis showed "islands" rich in Cs and Ti across the surface of the 1300 °C HIP sample, suggesting partial melting and partitioning of Cs into multiple phases. Photoemission data revealed multiple Cs 3d spin-orbit pairs for the HIP samples, with the lower binding energy doublets likely corresponding to Cs located in more leachable phases. Among all specimens examined, the melt-processed sample exhibited the lowest fractional release rates for Rb and Cs. However, the retention of Sr and Mo was greater in the HIP specimens.

Factors influencing the creep strength of hot pressed beryllium

International Nuclear Information System (INIS)

Webster, D.; Crooks, D.D.

1975-01-01

The parameters controlling the creep strength of hot pressed beryllium block have been determined. Creep strength was improved by a high initial dislocation density, a coarse grain size, and a low impurity content. The impurities most detrimental to creep strength were found to be aluminum, magnesium, and silicon. A uniform distribution of BeO was found to give creep strength which was inferior to a grain boundary distribution. The creep strength of very high purity, hot isostatically pressed beryllium was found to compare favorably with that of other more commonly used high temperature metals

Vacuum hot pressing of titanium-alloy powders

International Nuclear Information System (INIS)

Malik, R.K.

1975-01-01

Full or nearly full dense products of wrought-metal properties have been obtained by vacuum hot pressing (VHP) of several prealloyed Ti--6Al--4V powders including hydride, hydride/dehydride, and rotating electrode process (REP) spherical powder. The properties of billets VHP from Ti--6Al--4V hydride powder and from hydride/dehydride powders have been shown to be equivalent. The REP spherical powder billets processed by VHP or by hot isostatic pressing (HIP) resulted in equivalent tensile properties. The potential of VHP for fabrication of near net aircraft parts such as complex fittings and engine disks offers considerable cost savings due to reduced material and machining requirements

The kinetics of dolomite reaction rim growth under isostatic and non-isostatic pressure conditions

Science.gov (United States)

Helpa, V.; Rybacki, E.; Morales, L. G.; Abart, R.; Dresen, G. H.

2013-12-01

During burial and exhumation, rocks are simultaneously exposed to metamorphic reactions and tectonic stresses. Therefore, the reaction rate of newly formed minerals may depend on chemical and mechanical driving forces. Here, we investigate the reaction kinetics of dolomite (CaMg[CO3]2) rim growth by solid-state reactions experiments on oriented calcite (CaCO3) and magnesite (MgCO3) single crystals under isostatic and non-isostatic pressure conditions. Cylindrical samples of 3-5 mm length and 7 mm diameter were drilled and polished perpendicular to the rhombohedral cleavage planes of natural clear crystals. The tests were performed using a Paterson-type deformation apparatus at P = 400 MPa confining pressure, temperatures, T, between 750 and 850°C, and reaction durations, t, of 2 - 146 h to calculate the kinetic parameters of dolomite rim growth under isostatic stress conditions. For non-isostatic reaction experiments we applied in addition differential stresses, σ, up to 40 MPa perpendicular to the contact interface at T = 750°C for 4 - 171 h duration, initiating minor inelastic deformation of calcite. The thickness of the resulting dolomite reaction rims increases linearly with the square root of time, indicating a diffusion-controlled reaction. The rims consist of two different textural domains. Granular dolomite grains (≈ 2 -5 μm grain size) form next to calcite and elongated palisade-shaped grains (1-6 μm diameter) grow perpendicular to the magnesite interface. Texture measurements with the electron backscatter diffraction technique indicate that the orientations of dolomite grains are mainly influenced by the orientation of the calcite educt crystal, in particular in the granular rim. To some extent, the texture of dolomite palisades is also influenced by the orientation of magnesite. The thickness of the two individual layers increases with temperature. At 400 MPa isostatic pressure, T = 750°C and t = 29 hours, a 5 μm thick granular dolomite layer

Fundamental properties of monolithic bentonite buffer material formed by cold isostatic pressing for high-level radioactive waste repository

International Nuclear Information System (INIS)

Kawakami, S.; Yamanaka, Y.; Kato, K.; Asano, H.; Ueda, H.

1999-01-01

The methods of fabrication, handling, and emplacement of engineered barriers used in a deep geological repository for high level radioactive waste should be planned as simply as possible from the engineering and economic viewpoints. Therefore, a new concept of a monolithic buffer material around a waste package have been proposed instead of the conventional concept with the use of small blocks, which would decrease the cost for buffer material. The monolithic buffer material is composed of two parts of highly compacted bentonite, a cup type body and a cover. As the forming method of the monolithic buffer material, compaction by the cold isostatic pressing process (CIP) has been employed. In this study, monolithic bentonite bodies with the diameter of about 333 mm and the height of about 455 mm (corresponding to the approx. 1/5 scale for the Japanese reference concept) were made by the CIP of bentonite powder. The dry densities: ρd of the bodies as a whole were measured and the small samples were cut from several locations to investigate the density distribution. The swelling pressure and hydraulic conductivity as function of the monolithic body density for CIP-formed specimens were also measured. High density (ρd: 1.4--2.0 Mg/m 3 ) and homogeneous monolithic bodies were formed by the CIP. The measured results of the swelling pressure (3--15 MPa) and hydraulic conductivity (0.5--1.4 x 10 -13 m/s) of the specimens were almost the same as those for the uniaxial compacted bentonite in the literature. It is shown that the vacuum hoist system is an applicable handling method for emplacement of the monolithic bentonite

Impact properties of reduced activation ferritic/martensitic steel, F82H jointed by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Ogiwara, H.; Tanigawa, H. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan); Hirose, T. [Blanket Engineering Group, Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Enoeda, M. [Naka Fusion Research Establishment, J.A.E.R.I., Japan Atomic Energy Research Institute, Ibaraki-ken (Japan); Kohyama, A. [Kyoto Univ., lnstitute of Advanced Energy (Japan)

2007-07-01

Full text of publication follows: Reduced-activation ferritic/martensitic steels are the leading candidate structural material for the blanket system of fusion reactors. The important issue at the current stage is the finalization of a detailed manufacturing specification for ITER test blanket module. Hot isostatic pressing (HIP) process is one of the most important methods to fabricate the first wall with cooling channels. The objective of this paper is to optimize HIP condition to obtain the excellent joints mechanical properties. The materials used were F82H steels. The joint was produced by solid state HIP method. Before HIP treatments, specimens were heated in vacuum condition to out-gas. This treatment was conducted to decrease oxidation on the surfaces. HIP treatments were carried out for 2 h at 1100 deg. C - 140 MPa. The specimens were normalized at 960 deg. C for 0.5 h and tempered at 750 deg. C for 1.5 h. The bonding interface was characterized by scanning electron microscopy. Charpy impact tests and tensile tests were conducted to evaluate the mechanical properties of the HIP joint. Impact tests revealed that there were no significant differences in the ductile-brittle transition temperatures of HIP jointed specimens and base metal specimens, but the upper-shelf energy (USE) of the HIP joint specimens at room temperature was only about 10% of that of the base metal specimens. SEM observations of the fracture surface of HIP joint specimens revealed that a large number of oxides were formed on the HIP joint. This result indicates that oxides formed on the HIP joint are the dominant factor of the impact properties. Based on these results, the pre-HIP treatment conditions had been optimized to reduce the number of oxides, and USE of HIP joint specimens increased to about 50% of that of the base metal. The detailed analyses on the HIP joint microstructure will be reported. (authors)

Influences of hot-isostatic-pressing temperature on microstructure, tensile properties and tensile fracture mode of Inconel 718 powder compact

International Nuclear Information System (INIS)

Chang, Litao; Sun, Wenru; Cui, Yuyou; Yang, Rui

2014-01-01

Inconel 718 powders have been hot-isostatic-pressed (HIPed) at representative temperatures to investigate the variations in microstructure, tensile properties and tensile fracture mode of the powder compact. Microstructure of the powder compacts were characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and so on. The results showed that the interdendritic precipitates inherited from the powders were partially retained in the powder compacts when the powders were HIPed at or below 1210 °C but were eliminated when HIPed at and above 1260 °C. The grain size uniformity of the powder compacts first increases and then decreases with increasing HIPing temperature. Prior particle boundaries (PPBs) were observed in the powder compacts HIPed at and below 1260 °C but was eliminated when HIPed at 1275 °C. The PPBs were decorated with carbide particles, the amount of the carbide particles at the PPBs decreases with increasing HIPing temperature. Most of the PPBs were pinned by the carbide particles in the compacts HIPed at 1140 °C. When the HIPing temperature was increased to 1210 °C and 1260 °C, a large number of PPBs de-pinned and moved beyond the pinning carbide particles, leading to grain growth and leaving carbide particles at the site of the original PPBs within the new grains. With increasing HIPing temperature, the 0.2% yield strength of the powder compacts at 650 °C decreases, the tensile elongation increases, and the tensile fracture mode changed from inter-particle dominant fracture to fully dimple ductile fracture

Influences of hot-isostatic-pressing temperature on microstructure, tensile properties and tensile fracture mode of Inconel 718 powder compact

Energy Technology Data Exchange (ETDEWEB)

Chang, Litao [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China); University of Chinese Academy of Sciences, Beijing (China); Sun, Wenru; Cui, Yuyou [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China); Yang, Rui, E-mail: ryang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China)

2014-04-01

Inconel 718 powders have been hot-isostatic-pressed (HIPed) at representative temperatures to investigate the variations in microstructure, tensile properties and tensile fracture mode of the powder compact. Microstructure of the powder compacts were characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and so on. The results showed that the interdendritic precipitates inherited from the powders were partially retained in the powder compacts when the powders were HIPed at or below 1210 °C but were eliminated when HIPed at and above 1260 °C. The grain size uniformity of the powder compacts first increases and then decreases with increasing HIPing temperature. Prior particle boundaries (PPBs) were observed in the powder compacts HIPed at and below 1260 °C but was eliminated when HIPed at 1275 °C. The PPBs were decorated with carbide particles, the amount of the carbide particles at the PPBs decreases with increasing HIPing temperature. Most of the PPBs were pinned by the carbide particles in the compacts HIPed at 1140 °C. When the HIPing temperature was increased to 1210 °C and 1260 °C, a large number of PPBs de-pinned and moved beyond the pinning carbide particles, leading to grain growth and leaving carbide particles at the site of the original PPBs within the new grains. With increasing HIPing temperature, the 0.2% yield strength of the powder compacts at 650 °C decreases, the tensile elongation increases, and the tensile fracture mode changed from inter-particle dominant fracture to fully dimple ductile fracture.

2.5-min Isostatic Gravity Grid for the United States

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 2.5-min isostatic gravity data set was produced by regridding the 4-km residual isostatic gravity grid of the U.S. The isostatic residual gravity grid was...

Industrial production of insulators using isostatic compaction method

Energy Technology Data Exchange (ETDEWEB)

Drugoveiko, O.P.; Ermolaeva, L.V.; Koren' , M.G.; Kreimer, B.D.; Panichev, G.I.; Ponomarev, A.P.; Rutkovskii, V.N.

1985-07-01

The process of shaping ceramic products from powders using isostatic compaction method is finding increasing industrial application. The production of electrical-engineering porcelain using isostatic compaction method is, according to the authors, a promising direction since this method permits one to obtain large and complex shaped products having uniform density distribution. The authors introduce an automatic isostatic compaction line at the ''Proletarii'' Factory for the production of the IOS-110-20000UKhL, T1 type insulators having the described dimensions. According to the technological process developed at the ''Elektrokeramika'' Production Complex, insulators were manufactured on the isostatic compaction line from the G-33 mass. Presspowder having a moisture content of 0.3-0.6% and a particle size of 90-160 micrometers was obtained in a spray dryer using disk spraying. The authors studied saturability by moisture of the powder obtained.

Selective Electron Beam Manufacturing of Ti-6Al-4V Strips: Effect of Build Orientation, Columnar Grain Orientation, and Hot Isostatic Pressing on Tensile Properties

Science.gov (United States)

Wang, J.; Tang, H. P.; Yang, K.; Liu, N.; Jia, L.; Qian, M.

2018-03-01

Many novel designs for additive manufacturing (AM) contain thin-walled (≤ 3 mm) sections in different orientations. Selective electron beam melting (SEBM) is particularly suited to AM of such thin-walled titanium components because of its high preheating temperature and high vacuum. However, experimental data on SEBM of Ti-6Al-4V thin sections remains scarce because of the difficulty and high cost of producing long, thin and smooth strip tensile specimens (see Fig. 1). In this study, 80 SEBM Ti-6Al-4V strips (180 mm long, 42 mm wide, 3 mm thick) were built both vertically (V-strips) and horizontally (H-strips). Their density, microstructure and tensile properties were investigated. The V-strips showed clearly higher tensile strengths but lower elongation than the H-strips. Hot isostatic pressing (HIP) produced the same lamellar α-β microstructures in terms of the average α-lath thickness in both types of strips. The retained prior-β columnar grain boundaries after HIP showed no measurable influence on the tensile properties, irrespective of their length and orientation, because of the formation of randomly distributed fine α-laths.[Figure not available: see fulltext.

Ceramic containers for spent nuclear fuel. II. Reactions between TiO2 and the steel canning during hot isostatic processing

International Nuclear Information System (INIS)

Bergman, B.; Forberg, S.

1984-01-01

Rutile was selected for some practical studies of processing and properties of ceramic containers. Hot isostatic pressing at 1280 0 C has resulted in reaction zones between the TiO 2 powder and the steel canning. The phases ilmenite, pseudobrookite, rutile, and iron have been identified by x-ray diffraction and by microprobe analysis. The microstructures have been interpreted by classical metallographic methods, and some microstructures obtained by hot pressing and rapid cooling have also been examined for purposes of comparison. Some implications of the microstructures have been discussed in terms of microcracking and slow crack growth. 13 refs., 7 figs

Application of isostatic gravity anomaly in the Yellow Sea area

Science.gov (United States)

Hao, Z.; Qin, J.; Huang, W.; Wu, X.

2017-12-01

In order to study the deep crustal structure of the Yellow Sea area, we used the Airy-Heiskanen model to calculate the isostatic gravity anomaly of this area. Based on the Bouguer gravity anomaly and water depth data of this area, we chose the calculating parameters as standard crustal thickness 30 km, crust-mantle density difference 0.6g/cm3and grid spacing 0.1°×0.1°. This study reveals that there are six faults and four isostatic negative anomalies in the study area. The isostatic anomalies in much of Yellow Sea areas give priority to those with positive anomalies. The isostatic anomalies in North Yellow Sea are higher than South Yellow Sea with Jiashan-Xiangshui fault as the boundary. In the north of the study area, isostatic anomalies are characterized by large areas of positive anomaly. The change is relatively slow, and the trends give priority to the trend NE or NEE. In the middle of the north Yellow Sea basin, there is a local negative anomaly, arranged as a string of beads in NE to discontinuous distribution. Negative anomaly range is small, basically corresponds to the region's former Cenozoic sedimentary basin position. To the south of Jiashan-Xiangshui fault and west of Yellow Sea eastern margin fault, including most of the south Yellow Sea and Jiangsu province, the isostatic anomalies are lower. And the positive and negative anomalies are alternative distribution, and negative anomaly trap in extensive development. The trends give priority to NE, NEE, both to the NW. On the basis of the characteristics of isostatic gravity anomalies, it is concluded that the Yellow Sea belongs to continental crustal isostatic area whose isostatic anomalies is smooth and slow. ReferencesHeiskanen, W. A., F. A. V. Meinesz, and S. A. Korff (1958), The Earth and Its Gravity Field, McGraw-Hill, New York. Meng, X. J., X. H. Zhang, and J. Y. Yang (2014), Geophysical survey in eastern China seas and the characteristics of gravity and magnetic fields, Marine Geoglogy

Microstructural and Microhardness Evolution from Homogenization and Hot Isostatic Pressing on Selective Laser Melted Inconel 718: Structure, Texture, and Phases

Directory of Open Access Journals (Sweden)

Raiyan Seede

2018-05-01

Full Text Available In this work, the microstructure, texture, phases, and microhardness of 45° printed (with respect to the build direction homogenized, and hot isostatically pressed (HIP cylindrical IN718 specimens are investigated. Phase morphology, grain size, microhardness, and crystallographic texture at the bottom of each specimen differ from those of the top due to changes in cooling rate. High cooling rates during the printing process generated a columnar grain structure parallel to the building direction in the as-printed condition with a texture transition from (001 orientation at the bottom of the specimen to (111 orientation towards the specimen top based on EBSD analysis. A mixed columnar and equiaxed grain structure associated with about a 15% reduction in texture is achieved after homogenization treatment. HIP treatment caused significant grain coarsening, and engendered equiaxed grains with an average diameter of 154.8 µm. These treatments promoted the growth of δ-phase (Ni3Nb and MC-type brittle (Ti, NbC carbides at grain boundaries. Laves phase (Fe2Nb was also observed in the as-printed and homogenized specimens. Ostwald ripening of (Ti, NbC carbides caused excessive grain growth at the bottom of the HIPed IN718 specimens, while smaller grains were observed at their top. Microhardness in the as-fabricated specimens was 236.9 HV and increased in the homogenized specimens by 19.3% to 282.6 HV due to more even distribution of secondary precipitates, and the nucleation of smaller grains. A 36.1% reduction in microhardness to 180.5 HV was found in the HIPed condition due to   γ ″ phase dissolution and differences in grain morphology.

Nevada Isostatic Gravity Grid

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — A 2 kilometer Isostatic anomaly grid for the state of Nevada. Number of columns is 269 and number of rows is 394. The order of the data is from the lower left to the...

Influence of heat treatment on microstructure and tensile behavior of a hot isostatically pressed nickel-based superalloy

Energy Technology Data Exchange (ETDEWEB)

Qiu, Chunlei, E-mail: c.qiu@bham.ac.uk [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Wu, Xinhua; Mei, Junfa [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Andrews, Paul; Voice, Wayne [Rolls-Royce Plc, Derby DE24 8BJ (United Kingdom)

2013-11-25

Highlights: •Post-HIP heat treatment led to refined microstructure and improved tensile properties. •Deformation occurred mainly by forming stacking faults in γ′ at RT and elevated temperature. •Net-shape HIPed RR1000 failed in a transgranular fracture mode. -- Abstract: A nickel-based superalloy powder RR1000 has been hot isostatically pressed (HIPed) and heat treated to produce different microstructures. Microstructures were investigated using a scanning electron microscope (SEM). Tensile testing was performed at room temperature and 700 °C and the deformed samples were examined using SEM and transmission electron microscope (TEM). It was found that in the as-HIPed condition the microstructure consisted of coarse and irregular-shaped primary and secondary γ′ together with a low volume fraction of fine γ′ (<50 nm in diameter). Solution treatment below the γ′ solvus followed by air cooling resulted in the formation of finer cuboidal secondary γ′ (350–750 nm) and medium-sized spherical tertiary γ′ (100–200 nm). This led to an improvement of both the 0.2% yield strength and ultimate tensile strength. Ageing of the solution-treated or of the as-HIPed samples at 760 °C resulted in the precipitation of a high population of fine γ′ (around 50 nm) which further increased the strength. Within the resolution limit of the current TEM analysis, deformation at room temperature seemed to occur mainly by dislocations cutting through secondary γ′ and very fine γ′, accompanied by the formation of stacking faults within these precipitates; most of the medium-sized tertiary γ′ precipitates in solution-treated and aged samples were not cut through but were surrounded by dislocations. Deformation at 700 °C happened by dislocations cutting through γ′ precipitates and γ matrix, leading to the formation of extended stacking faults across both γ and γ′. It is suggested that the optimum treatment of the current powder superalloy is to

Influence of heat treatment on microstructure and tensile behavior of a hot isostatically pressed nickel-based superalloy

International Nuclear Information System (INIS)

Qiu, Chunlei; Wu, Xinhua; Mei, Junfa; Andrews, Paul; Voice, Wayne

2013-01-01

Highlights: •Post-HIP heat treatment led to refined microstructure and improved tensile properties. •Deformation occurred mainly by forming stacking faults in γ′ at RT and elevated temperature. •Net-shape HIPed RR1000 failed in a transgranular fracture mode. -- Abstract: A nickel-based superalloy powder RR1000 has been hot isostatically pressed (HIPed) and heat treated to produce different microstructures. Microstructures were investigated using a scanning electron microscope (SEM). Tensile testing was performed at room temperature and 700 °C and the deformed samples were examined using SEM and transmission electron microscope (TEM). It was found that in the as-HIPed condition the microstructure consisted of coarse and irregular-shaped primary and secondary γ′ together with a low volume fraction of fine γ′ (<50 nm in diameter). Solution treatment below the γ′ solvus followed by air cooling resulted in the formation of finer cuboidal secondary γ′ (350–750 nm) and medium-sized spherical tertiary γ′ (100–200 nm). This led to an improvement of both the 0.2% yield strength and ultimate tensile strength. Ageing of the solution-treated or of the as-HIPed samples at 760 °C resulted in the precipitation of a high population of fine γ′ (around 50 nm) which further increased the strength. Within the resolution limit of the current TEM analysis, deformation at room temperature seemed to occur mainly by dislocations cutting through secondary γ′ and very fine γ′, accompanied by the formation of stacking faults within these precipitates; most of the medium-sized tertiary γ′ precipitates in solution-treated and aged samples were not cut through but were surrounded by dislocations. Deformation at 700 °C happened by dislocations cutting through γ′ precipitates and γ matrix, leading to the formation of extended stacking faults across both γ and γ′. It is suggested that the optimum treatment of the current powder superalloy is to

Jamming of soft particles: geometry, mechanics, scaling and isostaticity

International Nuclear Information System (INIS)

Van Hecke, M

2010-01-01

Amorphous materials as diverse as foams, emulsions, colloidal suspensions and granular media can jam into a rigid, disordered state where they withstand finite shear stresses before yielding. Here we review the current understanding of the transition to jamming and the nature of the jammed state for disordered packings of particles that act through repulsive contact interactions and are at zero temperature and zero shear stress. We first discuss the breakdown of affine assumptions that underlies the rich mechanics near jamming. We then extensively discuss jamming of frictionless soft spheres. At the jamming point, these systems are marginally stable (isostatic) in the sense of constraint counting, and many geometric and mechanical properties scale with distance to this jamming point. Finally, we discuss current explorations of jamming of frictional and non-spherical (ellipsoidal) particles. Both friction and asphericity tune the contact number at jamming away from the isostatic limit, but in opposite directions. This allows one to disentangle the distance to jamming and the distance to isostaticity. The picture that emerges is that most quantities are governed by the contact number and scale with the distance to isostaticity, while the contact number itself scales with the distance to jamming. (topical review)

Jamming of soft particles: geometry, mechanics, scaling and isostaticity

Energy Technology Data Exchange (ETDEWEB)

Van Hecke, M, E-mail: mvhecke@physics.leidenuniv.n [Kamerlingh Onnes Laboratory, Leiden University, PO Box 9504, 2300 RA Leiden (Netherlands)

2010-01-27

Amorphous materials as diverse as foams, emulsions, colloidal suspensions and granular media can jam into a rigid, disordered state where they withstand finite shear stresses before yielding. Here we review the current understanding of the transition to jamming and the nature of the jammed state for disordered packings of particles that act through repulsive contact interactions and are at zero temperature and zero shear stress. We first discuss the breakdown of affine assumptions that underlies the rich mechanics near jamming. We then extensively discuss jamming of frictionless soft spheres. At the jamming point, these systems are marginally stable (isostatic) in the sense of constraint counting, and many geometric and mechanical properties scale with distance to this jamming point. Finally, we discuss current explorations of jamming of frictional and non-spherical (ellipsoidal) particles. Both friction and asphericity tune the contact number at jamming away from the isostatic limit, but in opposite directions. This allows one to disentangle the distance to jamming and the distance to isostaticity. The picture that emerges is that most quantities are governed by the contact number and scale with the distance to isostaticity, while the contact number itself scales with the distance to jamming. (topical review)

Characteristics of isostatic gravity anomaly in Sichuan-Yunnan region, China

Directory of Open Access Journals (Sweden)

Bingcheng Liu

2017-07-01

Full Text Available Sichuan-Yunnan region in China, a tectonic transition belt where earthquakes occurred frequently and intensely, has a distinct variation characteristic of gradient zone of Bouguer gravity anomaly (BGA. Many deep faults and epicenters of severe earthquake scatter along the BGA gradient zones. Here we apply two forward models (Airy model and Vening Meinesz model of isostatic gravity mechanisms (local versus regional in this region to calculated the isostatic gravity anomaly (IGA. Afterwards, the relationship between IGA and distribution of faults as well as seismicity is also illustrated. The IGA results show that the two models are similar and most parts of the study area are in an isostatic state. Most featured faults are distributed along the steep anomaly gradient zones; earthquakes tend to occur in the non-isostatic area and steep gradient belt of IGA. The distribution of root thickness based on regional mechanism can be associated with the main trend of BGA variation. The regional mechanism is more plausible and closer to the reality because of its relatively further consideration of the horizontal forces derived from adjacent particles in the crust. Then we analyze the effect of isostasy on the tectonic movements and find that the isostatic adjustment is not the main cause of the continuous uplift process of Longmenshan Mountain fault zone, which is due to the Indian-Eurasian continental collision.

Manufacturing and mechanical property test of the large-scale oxide dispersion strengthened martensitic mother tube by hot isostatic pressing and hot extrusion process

International Nuclear Information System (INIS)

Narita, Takeshi; Ukai, Shigeharu; Kaito, Takeji; Ohtsuka, Satoshi; Fujiwara, Masayuki

2003-09-01

Mass production capability of Oxide Dispersion Strengthened (ODS) ferritic steel cladding (9Cr) is evaluated in the Phase II of the Feasibility Studies on Commercialized Fast Reactor Cycle System. The cost for manufacturing mother tube is a dominant factor in the total cost for manufacturing ODS ferritic cladding. In this study, the large-scale 9Cr-ODS martensitic mother tube was produced by overseas supplier with mass production equipments for commercialized ODS steels. The process of manufacturing the ODS mother tube consists of raw material powder production, mechanical alloying by high energy ball mill, hot isostatic pressing(HIP), and hot extrusion. Following results were obtained in this study. (1) Micro structure of the ODS steels is equivalent to that of domestic products, and fine oxides are uniformly distributed. The mechanical alloying by large capacity (1 ton) ball mill can be satisfactorily carried out. (2) A large scale mother tube (65 mm OD x 48 mm ID x 10,000 mm L), which can produce about 60 pieces of 3 m length ODS ferritic claddings by four times cold rolling, have been successfully manufactured through HIP and Hot Extrusion process. (3) Rough surface of the mother tubes produced in this study can be improved by selecting the reasonable hot extrusion condition. (4) Hardness and tensile strength of the manufactured ODS steels are lower than domestic products with same chemical composition. This is owing to the high aluminum content in the product, and those properties could be improved by decreasing the aluminum content in the raw material powder. (author)

Investigation of the Microstructure and Mechanical Properties of Copper-Graphite Composites Reinforced with Single-Crystal α-Al₂O₃ Fibres by Hot Isostatic Pressing.

Science.gov (United States)

Zhang, Guihang; Jiang, Xiaosong; Qiao, ChangJun; Shao, Zhenyi; Zhu, Degui; Zhu, Minhao; Valcarcel, Victor

2018-06-11

Single-crystal α-Al₂O₃ fibres can be utilized as a novel reinforcement in high-temperature composites owing to their high elastic modulus, chemical and thermal stability. Unlike non-oxide fibres and polycrystalline alumina fibres, high-temperature oxidation and polycrystalline particles boundary growth will not occur for single-crystal α-Al₂O₃ fibres. In this work, single-crystal α-Al₂O₃ whiskers and Al₂O₃ particles synergistic reinforced copper-graphite composites were fabricated by mechanical alloying and hot isostatic pressing techniques. The phase compositions, microstructures, and fracture morphologies of the composites were investigated using X-ray diffraction, a scanning electron microscope equipped with an X-ray energy-dispersive spectrometer (EDS), an electron probe microscopic analysis equipped with wavelength-dispersive spectrometer, and a transmission electron microscope equipped with EDS. The mechanical properties have been measured by a micro-hardness tester and electronic universal testing machine. The results show that the reinforcements were unevenly distributed in the matrix with the increase of their content and there were some micro-cracks located at the interface between the reinforcement and the matrix. With the increase of the Al₂O₃ whisker content, the compressive strength of the composites first increased and then decreased, while the hardness decreased. The fracture and strengthening mechanisms of the composite materials were explored on the basis of the structure and composition of the composites through the formation and function of the interface. The main strengthening mechanism in the composites was fine grain strengthening and solid solution strengthening. The fracture type of the composites was brittle fracture.

U.S. Isostatic Residual Gravity Grid

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — isores.bin - standard grid containing isostatic residual gravity map for U.S. Grid interval = 4 km. Projection is Albers (central meridian = 96 degrees West; base...

Strength-ductility relationships in intermediate purity hot-pressed beryllium

International Nuclear Information System (INIS)

Stonehouse, A.J.; Bielawski, C.A.; Paine, R.M.

1977-01-01

The strength of vacuum hot-pressed, intermediate purity beryllium may be substantially increased without sacrifice of the strain capacity of the present grade (S-65) through decrease in the average grain size. Tensile strength of 517 MPa, 0.2% offset yield strength of 414 MPa with minimum 3% tensile elongation in all test directions could be commercially achieved. The tangent modulus of such material is quite attractive and suffers only about 10% degradation from room temperature to 260 0 C. The tangent modulus is dramatically enhanced by the presence of a yield point. The ductility of the materials studied did not appear to be affected by the BeO content across the range of 0.5 to 2.0% using nominal -44 to -15 μm powder particle sizes. All fine-grained pressings exhibited yield points in the as-pressed condition. Either full-density or sub-density hot-pressed billets given a hot isostatic pressing treatment without the use of cans showed only slight yield points after the HIP treatment with essentially the same strength and ductility factors as in the pressed condition. A plot of grain size vs yield strength in the as-pressed condition projects to an intercept with the fracture strength line at about 3 μm grain size. A similar plot after the HIP treatment shows a yield strength line parallel to the fracture strength line with no projected intercept predicting a completely brittle material. (author)

MANU. Isostatic compression of buffer blocks. Small scale

International Nuclear Information System (INIS)

Laaksonen, R.

2010-01-01

between density, moisture, degree of saturation and strength of the specimen. Also tests should be carried out to produce information on homogeneity of large specimens and information on the effect of the isostatic pressure and duration of the compression. Tests should be done to show that also granulated material follows the found water content density relationship and to study the material loss due to machining to the final block dimensions. This must be done with large samples. Techniques like vibration or vacuum - separately or combined - may be used to precompact the material in the mould to reduce both mould size and contraction of the sample and tool material during pressing. It may also be possible to reshape the mould with a vacuum inside. Tests should also be carried out to study the swelling capacity of materials compressed to different densities under different water contents - both swelling pressure and volume increase capacity due to swelling. (orig.)

Effect of standard heat treatment on the microstructure and mechanical properties of hot isostatically pressed superalloy inconel 718

International Nuclear Information System (INIS)

Rao, G. Appa; Kumar, Mahendra; Srinivas, M.; Sarma, D.S.

2003-01-01

Ni-Fe base superalloy, Inconel 718, was processed through powder metallurgy (P/M) hot isostatic pressing (HIP) route. In order to balance the strength and ductility, the HIPed material was given the standard heat treatment, viz. solution treatment at 980 deg. C for 1 h/water quenched (WQ) to room temperature and a two-step ageing treatment consisting of 720 deg. C for 8 h/furnace cooling (FC) at 55 deg. C h -1 to 620 deg. C and holding at 620 deg. C for 8 h before air cooling (AC) to room temperature. Optical microscopy and scanning electron microscopy (SEM) studies on the heat treated alloy have shown a homogeneous microstructure with fine grain size (25 μm) along with the presence of prior particle boundary (PPB) networks. Transmission electron microscopy (TEM) on the heat treated material has revealed the presence of oxides, MC carbides and δ-precipitates at the grain boundaries and a uniform precipitation of fine γ'' and γ' strengthening phases in the matrix. Tensile and stress rupture tests were performed on the heat treated material. While the yield strength (YS) and ultimate tensile strength (UTS) of the HIPed and heat treated alloy at room temperature and 650 deg. C were comparable to those of conventionally processed wrought IN 718, its ductility was lower. The stress rupture life of the HIPed alloy improved marginally due to heat treatment and met the minimum specification requirement of life hours but the rupture ductility was found to be inferior to that of the wrought material. The fractography of the failed samples has revealed the transgranular ductile mode of fracture in the as-solution treated alloy, while intergranular mode of failure with the decohesion of PPBs occurred more predominantly in the aged condition. This change of fracture mode with ageing treatment shows the ductility dependence on the relative strength of the matrix and PPBs. The TEM studies on the deformed alloy have revealed that the brittle oxides and carbides at the prior

Isostatic models and isostatic gravity anomalies of the Arabian plate and surroundings

OpenAIRE

M. K. Kaban; Sami El Khrepy; Nassir Al-Arifi

2015-01-01

Isostaic anomalies represent one of the most useful “geological” reduction of the gravity field. With the isostatic correction it is possible to remove a significant part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomalies. This correction is based on the fact that a major part of the near-surface load is compensated by variations of the lithosphere boundaries (chiefly the Moho and LAB) and by density variations within the crust and upper man...

Effects of internal gas pressure and microstructure on the mechanisms of hot-pressing and swelling in ceramics. Progress report, June 1, 1976--March 31, 1977

International Nuclear Information System (INIS)

Solomon, A.A.

1977-02-01

The low temperature isostatic pressurization system has been completed, operated successfully and calibrated. The new high temperature TD tungsten vessel and MoSi 2 element furnace system has also been designed and is presently under construction. Porous CoO single crystals have been grown using a ''skull melting'' process. Automated quantitative microscopy techniques are being developed using the KONTRON system to examine porosity evaluation during hot-pressing and sintering. Initial sintering experiments under variable isostatic pressures from 100 μm Hg to 2000 psi reveal no significant effect of ambient pressure. Nor were differences observed in sintering kinetics when either Helium or Argon were used as the pressurizing gas. Swelling experiments, conducted by reducing the ambient pressure after pore closure, revealed dramatic changes in density. The densification rates also appeared to depend on history, suggesting that mechanical deformation may play a dominant role in hot-pressing, at least during transients

Growth kinetics and microstructural evolution during hot isostatic pressing of U-10 wt.% Mo monolithic fuel plate in AA6061 cladding with Zr diffusion barrier

Science.gov (United States)

Park, Y.; Yoo, J.; Huang, K.; Keiser, D. D.; Jue, J. F.; Rabin, B.; Moore, G.; Sohn, Y. H.

2014-04-01

Phase constituents and microstructure changes in RERTR fuel plate assemblies as functions of temperature and duration of hot-isostatic pressing (HIP) during fabrication were examined. The HIP process was carried out as functions of temperature (520, 540, 560 and 580 °C for 90 min) and time (45-345 min at 560 °C) to bond 6061 Al-alloy to the Zr diffusion barrier that had been co-rolled with U-10 wt.% Mo (U10Mo) fuel monolith prior to the HIP process. Scanning and transmission electron microscopies were employed to examine the phase constituents, microstructure and layer thickness of interaction products from interdiffusion. At the interface between the U10Mo and Zr, following the co-rolling, the UZr2 phase was observed to develop adjacent to Zr, and the α-U phase was found between the UZr2 and U10Mo, while the Mo2Zr was found as precipitates mostly within the α-U phase. The phase constituents and thickness of the interaction layer at the U10Mo-Zr interface remained unchanged regardless of HIP processing variation. Observable growth due to HIP was only observed for the (Al,Si)3Zr phase found at the Zr/AA6061 interface, however, with a large activation energy of 457 ± 28 kJ/mole. Thus, HIP can be carried to improve the adhesion quality of fuel plate without concern for the excessive growth of the interaction layer, particularly at the U10Mo-Zr interface with the α-U, Mo2Zr, and UZr2 phases.

Growth kinetics and microstructural evolution during hot isostatic pressing of U-10 wt.% Mo monolithic fuel plate in AA6061 cladding with Zr diffusion barrier

International Nuclear Information System (INIS)

Park, Y.; Yoo, J.; Huang, K.; Keiser, D.D.; Jue, J.F.; Rabin, B.; Moore, G.; Sohn, Y.H.

2014-01-01

Phase constituents and microstructure changes in RERTR fuel plate assemblies as functions of temperature and duration of hot-isostatic pressing (HIP) during fabrication were examined. The HIP process was carried out as functions of temperature (520, 540, 560 and 580 °C for 90 min) and time (45–345 min at 560 °C) to bond 6061 Al-alloy to the Zr diffusion barrier that had been co-rolled with U-10 wt.% Mo (U10Mo) fuel monolith prior to the HIP process. Scanning and transmission electron microscopies were employed to examine the phase constituents, microstructure and layer thickness of interaction products from interdiffusion. At the interface between the U10Mo and Zr, following the co-rolling, the UZr 2 phase was observed to develop adjacent to Zr, and the α-U phase was found between the UZr 2 and U10Mo, while the Mo 2 Zr was found as precipitates mostly within the α-U phase. The phase constituents and thickness of the interaction layer at the U10Mo-Zr interface remained unchanged regardless of HIP processing variation. Observable growth due to HIP was only observed for the (Al,Si) 3 Zr phase found at the Zr/AA6061 interface, however, with a large activation energy of 457 ± 28 kJ/mole. Thus, HIP can be carried to improve the adhesion quality of fuel plate without concern for the excessive growth of the interaction layer, particularly at the U10Mo-Zr interface with the α-U, Mo 2 Zr, and UZr 2 phases

Tectonics and Non-isostatic Topography of the Mariana Trench and Adjacent Plates

Science.gov (United States)

Hongyu, L.; Lin, J.; Zhou, Z.; Zhang, F.

2017-12-01

Multi-types of geophysical data including multibeam bathymetry, sediment thickness, gravity anomaly, and crustal magnetic age were analyzed to investigate tectonic processes of the Mariana Trench and the surrounding plates. We calculated non-Airy-isostatic topography by removing from the observed bathymetry the effects of sediment loading, thermal subsidence, and Airy local isostatically-compensated topography. The Mariana Trench was found to be associated with a clearly defined zone of negative non-isostatic topography, which was caused by flexural bending of the subducting Pacific plate and with the maximum depth anomaly and flexural bending near the Challenger Deep. In contrast, the Caroline Ridge and Caroline Islands Chain have much more subdued non-isostatic topography, indicating their higher topography is largely compensated by thicker crust. Along the Mariana Trough, the northern and central segments appear to be associated with relatively low magma supply as indicated by the relatively low topography and thin crust. In contrast, the southern Mariana Trough is associated with relatively high magma supply as indicated by the relatively high and smoother topography, an axial high spreading center, and relatively thick crust. The southern end of the Mariana Trough was also found to be associated with positive non-isostatic topographic anomaly, which might be caused by the complex tectonic deformation of the overriding Mariana and Philippine Sea plates and their interaction with the subducting Pacific plate. Analysis further revealed that the southern Mariana Arc, located between the Mariana Trench and Mariana Trough, is associated with positive non-isostatic topographic anomalies, which may be explained by the late stage magmatic loading on the older and thus stronger lithospheric plate of the Mariana volcanic arc.

Hot isostatically-pressed aluminosilicate glass-ceramic with natural crystalline analogues for immobilizing the calcined high-level nuclear waste at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Raman, S.

1993-12-01

The additives Si, Al, MgO, P 2 O 5 were mechanically blended with fluorinelsodium calcine in varying proportions. The batches were vacuum sealed in stainless steel canisters and hot isostatically pressed at 20,000 PSI and 1000 C for 4 hours. The resulting suite of glass-ceramic waste forms parallels the natural rocks in microstructural and compositional heterogeneity. Several crystalline phases ar analogous in composition and structure to naturally occurring minerals. Additional crystalline phases are zirconia and Ca-Mg borate. The glasses are enriched in silica and alumina. Approximately 7% calcine elements occur dissolved in this glass and the total glass content in the waste forms averages 20 wt%. The remainder of the calcine elements are partitioned into crystalline phases at 75 wt% calcine waste loading. The waste forms were tested for chemical durability in accordance with the MCC1-test procedure. The leach rates are a function of the relative proportions of additives and calcine, which in turn influence the composition and abundances of the glass and crystalline phases. The DOE leach rate criterion of less than 1 g/m 2 -day is met by all the elements B, Cs and Na are increased by lowering the melt viscosity. This is related to increased crystallization or devitrification with increases in MgO addition. This exploratory work has shown that the increases in waste loading occur by preferred partitioning of the calcine components among crystalline and glass phases. The determination of optimum processing parameters in the form of additive concentration levels, homogeneous blending among the components, and pressure-temperature stabilities of phases must be continued to eliminate undesirable effects of chemical composition, microstructure and glass devitrification

Idaho Batholith Study Area Isostatic Gravity Grid

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — A 2 kilometer isostatic gravity grid for the Idaho batholith study area. Number of columns is 331 and number of rows is 285. The order of the data is from the lower...

Silicon nitride-fabrication, forming and properties

International Nuclear Information System (INIS)

Yehezkel, O.

1983-01-01

This article, which is a literature survey of the recent years, includes description of several methods for the formation of silicone nitride, and five methods of forming: Reaction-bonded silicon nitride, sintering, hot pressing, hot isostatic pressing and chemical vapour deposition. Herein are also included data about mechanical and physical properties of silicon nitride and the relationship between the forming method and the properties. (author)

Comparison of various isostatic marine gravity disturbances

Indian Academy of Sciences (India)

due to the fact that the same isostatic principle is applied in both these definitions expect for assuming a local (in the ..... Gladkikh V and Tenzer R 2011 A mathematical model of the ... and its Gravity Field; McGraw-Hill Book Company, Inc.

The alignment and isostatic mount bonding technique of the aerospace Cassegrain telescope primary mirror

Science.gov (United States)

Lin, Wei Cheng; Chang, Shenq-Tsong; Lin, Yu-Chuan; Hsu, Ming-Ying; Chang, Yu-Ting; Chang, Sheng-Hsiung; Huang, Ting-Ming

2012-10-01

In order to meet both optical performance and structural stiffness requirements of the aerospace Cassegrain telescope, iso-static mount is used as the interface between the primary mirror and the main plate. This article describes the alignment and iso-static mount bonding technique of the primary mirror by assistance of CMM. The design and assembly of mechanical ground support equipment (MGSE) which reduces the deformation of primary mirror by the gravity effect is also presented. The primary mirror adjusting MGSE consists of X-Y linear translation stages, rotation stage and kinematic constrain platform which provides the function of decenter, orientation, tilt and height adjustment of the posture sequentially. After CMM measurement, the radius of curvature, conic constant, decenter and tilt, etc. will be calculated. According to these results, the posture of the mirror will be adjusted to reduce the tilt by the designed MGSE within 0.02 degrees and the distance deviation from the best fitted profile of mirror to main plate shall be less than 0.01 mm. After that, EC 2216 adhesive is used to bond mirror and iso-static mount. During iso-static mount bonding process, CMM is selected to monitor the relative position deviation of the iso-static mount until the adhesive completely cured. After that, the wave front sensors and strain gauges are used to monitor the strain variation while the iso-static mount mounted in the main plate with the screws by the torque wrench. This step is to prevent deformation of the mirror caused from force of the iso-static mount during the mounting process. In the end, the interferometer is used for the optical performance test with +1G and -1G to check the alignment and bonding technique is well or not.

Growth kinetics and microstructural evolution during hot isostatic pressing of U-10 wt.% Mo monolithic fuel plate in AA6061 cladding with Zr diffusion barrier

Energy Technology Data Exchange (ETDEWEB)

Park, Y.; Yoo, J.; Huang, K. [Advanced Materials Processing and Analysis Center, Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816 (United States); Keiser, D.D.; Jue, J.F.; Rabin, B.; Moore, G. [Idaho National Laboratory, PO Box 1625, Idaho Falls, ID 83401 (United States); Sohn, Y.H., E-mail: Yongho.sohn@ucf.edu [Advanced Materials Processing and Analysis Center, Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816 (United States)

2014-04-01

Phase constituents and microstructure changes in RERTR fuel plate assemblies as functions of temperature and duration of hot-isostatic pressing (HIP) during fabrication were examined. The HIP process was carried out as functions of temperature (520, 540, 560 and 580 °C for 90 min) and time (45–345 min at 560 °C) to bond 6061 Al-alloy to the Zr diffusion barrier that had been co-rolled with U-10 wt.% Mo (U10Mo) fuel monolith prior to the HIP process. Scanning and transmission electron microscopies were employed to examine the phase constituents, microstructure and layer thickness of interaction products from interdiffusion. At the interface between the U10Mo and Zr, following the co-rolling, the UZr{sub 2} phase was observed to develop adjacent to Zr, and the α-U phase was found between the UZr{sub 2} and U10Mo, while the Mo{sub 2}Zr was found as precipitates mostly within the α-U phase. The phase constituents and thickness of the interaction layer at the U10Mo-Zr interface remained unchanged regardless of HIP processing variation. Observable growth due to HIP was only observed for the (Al,Si){sub 3}Zr phase found at the Zr/AA6061 interface, however, with a large activation energy of 457 ± 28 kJ/mole. Thus, HIP can be carried to improve the adhesion quality of fuel plate without concern for the excessive growth of the interaction layer, particularly at the U10Mo-Zr interface with the α-U, Mo{sub 2}Zr, and UZr{sub 2} phases.

Finite element concept to derive isostatic residual maps ...

Indian Academy of Sciences (India)

A new space-domain operator based on the shape function concept of finite element analysis has been developed to derive the ... not require explicit assumptions on isostatic models. Besides .... This information is implicit in the Bouguer ...

Thermal stability of the grain structure in the W-2V and W-2V-0.5Y2O3 alloys produced by hot isostatic pressing

International Nuclear Information System (INIS)

Martínez, J.; Savoini, B.; Monge, M.A.; Muñoz, A.; Armstrong, D.E.J.; Pareja, R.

2013-01-01

Highlights: • W-2V and ODS W-2V-0.5Y 2 O 3 alloys have been produced following a powder metallurgy route. • Grain microstructure and microhardness have been studied after isothermal treatments in vacuum. • Both alloys exhibit a duplex grain size population: a submicron-sized grain and a coarse grained one. • The Y 2 O 3 addition inhibits growth of the coarse grains for T 2 O 3 nanoparticles enhance the microhardness of W-2V-0.5Y 2 O 3 . -- Abstract: W-2V and ODS W-2V-0.5Y 2 O 3 alloys have been produced following a powder metallurgy route consisting of mechanical alloying and a subsequent high isostatic pressing HIP at 1573 K. The grain microstructure and microhardness recovery of the alloys have been studied in samples subjected to isothermal treatments in vacuum in temperature range 1073–1973 K. Both alloys exhibit a duplex grain size distribution consisting of a submicron-sized grain and a coarse-grained population. It has been found that the Y 2 O 3 addition inhibits growth of the coarse grains at T 2 O 3 , respectively, was observed at T ≥ 1573 K. It resulted that the rate constant for grain growth is 30 times higher in W-2V-0.5Y 2 O 3 than in W-2V. The considerable enhancement of the microhardness in the W-2V-0.5Y 2 O 3 appears to be associated to dispersion strengthening

Isostatic anomaly characteristics and dynamic environment of New Britain Ocean trenches and neighboring Area in Papua New Guinea

Science.gov (United States)

Yang, G.; Shen, C.; Wang, J.

2017-12-01

we calculated the Bouguer gravity anomaly and the Airy-Heiskanen isostatic anomaly in the New Britain ocean trenches and its surrounding areas of Papua New Guinea using the topography model and the gravity anomaly model from Scripps Institute of Oceanography, and analyzed the characteristics of isostatic anomaly and the earthquake dynamic environment of this region. The results show that there are obviously differences in the isostatic state between each block in the region, and the crustal tectonic movement is very intense in the regions with high positive or negative isostatic gravity anomalies; A number of sub-plates in this area is driven by the external tectonic action such as plate subduction and thrust of the Pacific plate, the Indian - Australian plate and the Eurasian plate. From the distribution of isostatic gravity anomaly, the tectonic action of anti-isostatic movement in this region is the main source of power; from the isostatic gravity and the spatial distribution of the earthquake, with the further contraction of the Indian-Australian plate, the southwestern part of the Solomon Haiya plate will become part of the Owen Stanley fold belt, the northern part will enter the lower part of the Bismarck plate, eastern part will enter the front of the Pacific plate, the huge earthquake will migrate to the north and east of the Solomon Haiya plate.

The positive effect of hot isostatic pressing on improving the anisotropies of bending and impact properties in selective laser melted Ti-6Al-4V alloy

Energy Technology Data Exchange (ETDEWEB)

Wu, Ming-Wei, E-mail: mwwu@ntut.edu.tw; Lai, Pang-Hsin

2016-03-21

Selective laser melting (SLM) is a versatile additive manufacturing process for fabricating solid or porous metallic materials with complicated three-dimensional shapes. SLM Ti alloys, particularly Ti-6Al-4V, and other alloys have been manufactured and analyzed in numerous studies. However, the high anisotropy of the microstructures and inconsistent mechanical properties of SLM materials have been extensively reported, and these disadvantages could prohibit its widespread use. To clarify how to alleviate the anisotropic behaviors of SLM materials, the main objective of this study was to evaluate the influences of hot isostatic pressing (HIP) on the microstructure, densification, bending strength, impact toughness, and fracture behavior of the as-built Ti-6Al-4V alloy. The results showed that the vertical and horizontal building directions obviously affect the bending and impact properties of as-built alloys. The transverse rupture strength (TRS) and impact energy of the horizontally-built alloy were respectively found to be 48% and 100% higher than those of the vertically-built one. In the vertically-built alloy, disc-shaped building defects, identified by X-ray computed tomography (CT) and microscopy, obviously reduce the effective load-bearing cross-section and deteriorate the bending and impact performances. After HIP at 1000 °C/150 MPa, the α′-martensite structure in the as-built alloy is transformed into an α+β lamellar one, and the disc-shaped building defects are evidently eliminated. As a result, the impact energies of as-built vertical and horizontal specimens are improved by 28 J (560%) and 19 J (190%), respectively, and the TRS of the as-built vertical alloy is raised by 550 MPa (37%). Consequently, the discrepancies in TRS and impact energy between the HIPed vertical and horizontal specimens are merely 3% and 14%, respectively, and the anisotropic behaviors of the SLM Ti-6Al-4V alloy are thus substantially lessened.

The positive effect of hot isostatic pressing on improving the anisotropies of bending and impact properties in selective laser melted Ti-6Al-4V alloy

International Nuclear Information System (INIS)

Wu, Ming-Wei; Lai, Pang-Hsin

2016-01-01

Selective laser melting (SLM) is a versatile additive manufacturing process for fabricating solid or porous metallic materials with complicated three-dimensional shapes. SLM Ti alloys, particularly Ti-6Al-4V, and other alloys have been manufactured and analyzed in numerous studies. However, the high anisotropy of the microstructures and inconsistent mechanical properties of SLM materials have been extensively reported, and these disadvantages could prohibit its widespread use. To clarify how to alleviate the anisotropic behaviors of SLM materials, the main objective of this study was to evaluate the influences of hot isostatic pressing (HIP) on the microstructure, densification, bending strength, impact toughness, and fracture behavior of the as-built Ti-6Al-4V alloy. The results showed that the vertical and horizontal building directions obviously affect the bending and impact properties of as-built alloys. The transverse rupture strength (TRS) and impact energy of the horizontally-built alloy were respectively found to be 48% and 100% higher than those of the vertically-built one. In the vertically-built alloy, disc-shaped building defects, identified by X-ray computed tomography (CT) and microscopy, obviously reduce the effective load-bearing cross-section and deteriorate the bending and impact performances. After HIP at 1000 °C/150 MPa, the α′-martensite structure in the as-built alloy is transformed into an α+β lamellar one, and the disc-shaped building defects are evidently eliminated. As a result, the impact energies of as-built vertical and horizontal specimens are improved by 28 J (560%) and 19 J (190%), respectively, and the TRS of the as-built vertical alloy is raised by 550 MPa (37%). Consequently, the discrepancies in TRS and impact energy between the HIPed vertical and horizontal specimens are merely 3% and 14%, respectively, and the anisotropic behaviors of the SLM Ti-6Al-4V alloy are thus substantially lessened.

Finite element concept to derive isostatic residual maps ...

Indian Academy of Sciences (India)

These produce large regional lows that override or tend to mask the smaller anomalies originating from the mid and upper crustal geologic structures. The interpretation and understanding of these structures depend on how effectively the regional gravity anoma- lies are isolated so as to construct the isostatic residual maps.

Finite element concept to derive isostatic residual maps

Indian Academy of Sciences (India)

A new space-domain operator based on the shape function concept of finite element analysis has been developed to derive the residual maps of the Gorda Plate of western United States. The technique does not require explicit assumptions on isostatic models. Besides delineating the Gorda Plate boundary, the residual ...

An empirical model of glacio-isostatic movements and shore-level displacement in Fennoscandia

International Nuclear Information System (INIS)

Paasse, T.

2001-08-01

Shore-level displacement in Fennoscandia is mainly due to two co-operative vertical movements, glacio-isostatic uplift and global eustatic sea level rise. The course of the glacio-isostatic uplift has been made discernible according to an investigation of the lake-tilting phenomenon. This information made it possible to start an iteration process that has given mathematical expression for factors involved both within the isostatic movements and the eustatic rise. There are two components involved in glacio-isostatic uplift. The main uplift, still in progress, acts slowly and is thus called the slow component. Arctan functions have proved to be suitable tools for describing the slow component. There are two main factors involved in the function used for calculation; A s (m), the download factor and B s (y -1 ), which is an inertia factor. A strong linear correlation between the inertia factor Bs and lithosphere thickness has been found in the model. There was also a fast component involved in the crustal changes at the end of Late Weichselian and early Holocene. This component gave rise to fast subsidence followed by fast uplift during the final part of the deglaciation. Crustal subsidence is assumed to be due to reloading of the crust in the central parts of Fennoscandia during the Younger Dryas stadial. Normal distribution functions are used for calculating this component. Glacio-isostatic uplift and thus a regressive shore-level displacement was extremely rapid around 10,300 years BP. This fast regression was contemporaneous and occurred in a similar way at the West Coasts of Norway and Sweden as well as in the Baltic. The 'drainage' of the Baltic Ice Lake has been interpreted in the model as due to this fast regression. The slow component is most probably due to viscous flow in the asthenosphere and the fast component is assumed to be due to its elasticity

An empirical model of glacio-isostatic movements and shore-level displacement in Fennoscandia

Energy Technology Data Exchange (ETDEWEB)

Paasse, T. [Geological Survey of Sweden, Uppsala (Sweden)

2001-08-01

Shore-level displacement in Fennoscandia is mainly due to two co-operative vertical movements, glacio-isostatic uplift and global eustatic sea level rise. The course of the glacio-isostatic uplift has been made discernible according to an investigation of the lake-tilting phenomenon. This information made it possible to start an iteration process that has given mathematical expression for factors involved both within the isostatic movements and the eustatic rise. There are two components involved in glacio-isostatic uplift. The main uplift, still in progress, acts slowly and is thus called the slow component. Arctan functions have proved to be suitable tools for describing the slow component. There are two main factors involved in the function used for calculation; A{sub s} (m), the download factor and B{sub s} (y{sup -1} ), which is an inertia factor. A strong linear correlation between the inertia factor Bs and lithosphere thickness has been found in the model. There was also a fast component involved in the crustal changes at the end of Late Weichselian and early Holocene. This component gave rise to fast subsidence followed by fast uplift during the final part of the deglaciation. Crustal subsidence is assumed to be due to reloading of the crust in the central parts of Fennoscandia during the Younger Dryas stadial. Normal distribution functions are used for calculating this component. Glacio-isostatic uplift and thus a regressive shore-level displacement was extremely rapid around 10,300 years BP. This fast regression was contemporaneous and occurred in a similar way at the West Coasts of Norway and Sweden as well as in the Baltic. The 'drainage' of the Baltic Ice Lake has been interpreted in the model as due to this fast regression. The slow component is most probably due to viscous flow in the asthenosphere and the fast component is assumed to be due to its elasticity.

Idealized Compression Ratio for a Screw Briquetting Press

Directory of Open Access Journals (Sweden)

Peter Biath

2012-01-01

Full Text Available This paper deals with issues in determining the ideal compression ratio for a screw briquetting press. First, the principles of operation and a basic description of the main parts of a screw briquetting press are introduced. The next section describes the pressing space by means of 3D software. The pressing space was created using a Boolean subtract function. The final section of the paper measures the partial volumes of the pressing chamber in CATIA V5 by function of measuring. The measured values are substituted into the formula for the compression ratio, and the resulting evaluations are presented in the diagram in the conclusion of this paper.

Isostatic gravity map of the Point Sur 30 x 60 quadrangle and adjacent areas, California

Science.gov (United States)

Watt, J.T.; Morin, R.L.; Langenheim, V.E.

2011-01-01

This isostatic residual gravity map is part of a regional effort to investigate the tectonics and water resources of the central Coast Range. This map serves as a basis for modeling the shape of basins and for determining the location and geometry of faults in the area. Local spatial variations in the Earth's gravity field (after removing variations caused by instrument drift, earth-tides, latitude, elevation, terrain, and deep crustal structure), as expressed by the isostatic anomaly, reflect the distribution of densities in the mid- to upper crust, which in turn can be related to rock type. Steep gradients in the isostatic gravity field often indicate lithologic or structural boundaries. Gravity highs reflect the Mesozoic granitic and Franciscan Complex basement rocks that comprise both the northwest-trending Santa Lucia and Gabilan Ranges, whereas gravity lows in Salinas Valley and the offshore basins reflect the thick accumulations of low-density alluvial and marine sediment. Gravity lows also occur where there are thick deposits of low-density Monterey Formation in the hills southeast of Arroyo Seco (>2 km, Marion, 1986). Within the map area, isostatic residual gravity values range from approximately -60 mGal offshore in the northern part of the Sur basin to approximately 22 mGal in the Santa Lucia Range.

Utilizing Visual Effects Software for Efficient and Flexible Isostatic Adjustment Modelling

Science.gov (United States)

Meldgaard, A.; Nielsen, L.; Iaffaldano, G.

2017-12-01

The isostatic adjustment signal generated by transient ice sheet loading is an important indicator of past ice sheet extent and the rheological constitution of the interior of the Earth. Finite element modelling has proved to be a very useful tool in these studies. We present a simple numerical model for 3D visco elastic Earth deformation and a new approach to the design of such models utilizing visual effects software designed for the film and game industry. The software package Houdini offers an assortment of optimized tools and libraries which greatly facilitate the creation of efficient numerical algorithms. In particular, we make use of Houdini's procedural work flow, the SIMD programming language VEX, Houdini's sparse matrix creation and inversion libraries, an inbuilt tetrahedralizer for grid creation, and the user interface, which facilitates effortless manipulation of 3D geometry. We mitigate many of the time consuming steps associated with the authoring of efficient algorithms from scratch while still keeping the flexibility that may be lost with the use of commercial dedicated finite element programs. We test the efficiency of the algorithm by comparing simulation times with off-the-shelf solutions from the Abaqus software package. The algorithm is tailored for the study of local isostatic adjustment patterns, in close vicinity to present ice sheet margins. In particular, we wish to examine possible causes for the considerable spatial differences in the uplift magnitude which are apparent from field observations in these areas. Such features, with spatial scales of tens of kilometres, are not resolvable with current global isostatic adjustment models, and may require the inclusion of local topographic features. We use the presented algorithm to study a near field area where field observations are abundant, namely, Disko Bay in West Greenland with the intention of constraining Earth parameters and ice thickness. In addition, we assess how local

Nickel powders shape effect upon their isostatic compaction behavior

International Nuclear Information System (INIS)

Cytermann, R.; Auguin, B.; Defresne, A.; Gilles, P.

1975-01-01

Two carbonyl nickel powders of the same purity, one spherical, the other of very irregular shape, were isostatically compacted at pressures from 0.5 to 13Kbars with two compacting speeds: 1Kbar/s and 1Kbar/15s. The influence of the powder shapes on the electrical resistivity, tensile strength and microcalorimetric measurements was studied [fr

Thermal stability of the grain structure in the W-2V and W-2V-0.5Y{sub 2}O{sub 3} alloys produced by hot isostatic pressing

Energy Technology Data Exchange (ETDEWEB)

Martínez, J.; Savoini, B.; Monge, M.A. [Departamento de Física, Universidad Carlos III de Madrid, 28911-Leganés Madrid (Spain); Muñoz, A., E-mail: angel.munoz@uc3m.es [Departamento de Física, Universidad Carlos III de Madrid, 28911-Leganés Madrid (Spain); Armstrong, D.E.J. [Department of Materials, University of Oxford, Park Road, Oxford OX1 3PH (United Kingdom); Pareja, R. [Departamento de Física, Universidad Carlos III de Madrid, 28911-Leganés Madrid (Spain)

2013-10-15

Highlights: • W-2V and ODS W-2V-0.5Y{sub 2}O{sub 3} alloys have been produced following a powder metallurgy route. • Grain microstructure and microhardness have been studied after isothermal treatments in vacuum. • Both alloys exhibit a duplex grain size population: a submicron-sized grain and a coarse grained one. • The Y{sub 2}O{sub 3} addition inhibits growth of the coarse grains for T < 1973 K. • The Y{sub 2}O{sub 3} nanoparticles enhance the microhardness of W-2V-0.5Y{sub 2}O{sub 3}. -- Abstract: W-2V and ODS W-2V-0.5Y{sub 2}O{sub 3} alloys have been produced following a powder metallurgy route consisting of mechanical alloying and a subsequent high isostatic pressing HIP at 1573 K. The grain microstructure and microhardness recovery of the alloys have been studied in samples subjected to isothermal treatments in vacuum in temperature range 1073–1973 K. Both alloys exhibit a duplex grain size distribution consisting of a submicron-sized grain and a coarse-grained population. It has been found that the Y{sub 2}O{sub 3} addition inhibits growth of the coarse grains at T < 1973 K. Submicron grain growth, with activation enthalpy of 1.9 and 2.49 eV for W-2V and W-2V-0.5Y{sub 2}O{sub 3}, respectively, was observed at T ≥ 1573 K. It resulted that the rate constant for grain growth is 30 times higher in W-2V-0.5Y{sub 2}O{sub 3} than in W-2V. The considerable enhancement of the microhardness in the W-2V-0.5Y{sub 2}O{sub 3} appears to be associated to dispersion strengthening.

Effects of internal gas pressure and microstructure on the mechanisms of hot-pressing and swelling in ceramics. Progress report, June 1, 1975--March 31, 1976

International Nuclear Information System (INIS)

Solomon, A.A.

1976-02-01

Pressurization system components for studying the hot-pressing and swelling behavior of CoO were built. A vacuum furnace was modified so that dimensional changes can be continuously monitored during sintering under high vacuum. Chracterization of the CoO starting powders was initiated. A technique was developed to form geometrically uniform pellet compacts of high green density using low pressure punch and die pressing followed by high pressure isostatic compaction to obtain uniform green density. Preliminary sintering experiments were carried out at 1 atm in air, inert gas, and under vacuum with specimen deflection continuously monitored. Resulting microstructures were characterized using mercury porosimetry and quantitative optical microscopy. Drastic differences in sintering rates in vacuum and air were observed

Oxide formation and precipitation behaviors on interface of F82H steel joints during HIPing and hot pressing

International Nuclear Information System (INIS)

Kishimoto, H.; Ono, T.; Sakasegawa, H.; Tanigawa, H.; Ando, M.; Shibayama, T.; Kohno, Y.; Kohyama, A.

2013-01-01

Joining technologies for F82H steels are important issues for the development of fusion energy. The hot isostatic pressing (HIP) method is appropriate for consolidating the first wall of the blanket because of the flexibility of the shape of HIPed products. The HIP method is planned for fabricating a complex-shaped first wall component with built-in cooling channels; thus, accumulation of studies of microstructural and mechanical property changes, especially lower toughness of the HIPed joints, is essential. Present research aims to reveal the microstructural evolution of F82H joints fabricated by the HIP method compared with joints fabricated by hot pressing, focusing on the formation of oxides on the interface. F82H joints were characterized using 1/3-scale Charpy V-notch impact test, transmission electron microscope, scanning electron microscope, and electron probe analysis to survey the microstructural characteristics of the interface

The Darfur Swell, Africa: Gravity constraints on its isostatic compensation

Science.gov (United States)

Crough, S. Thomas

The free-air gravity anomaly observed over the Darfur Swell is explainable by local isostatic balance with a root approximately 50 km deep on average. This root depth is similar to that inferred beneath other African domes and beneath oceanic midplate swells, suggesting that the Darfur Swell is a hotspot uplift created by lithospheric reheating.

Structure and hardness of TiAl-TiB2 composite prepared by hot isostatic pressing of mechanically alloyed powders. Mekanikaru aroingu funmatsu no HIP shoketsu ni yori sakuseishita TiAl/TiB2 fukugo zairyo no soshiki to kodo

Energy Technology Data Exchange (ETDEWEB)

Sato, T; Shimakage, K [Muroran Inst. of Technology, Hokkaido (Japan). Faculty of Engineering; Miyakawa, S [Muroran Inst. of Technology, Hokkaido (Japan). Graduate Student

1992-11-20

The practical application of Ti-Al system intermetallic compounds is expected as an advanced light heat resistant material. TiAl group out of them, as for the specific strength, has an equivalent maximum working temperature as that of the nickel base alloy, which is utilized as a turbine material for the current aircraft, and moreover it is also said that it is superior in the creep and rupture properties to the latter. In this study, by mechanical alloying (MA) of each mixed powder of Ti-Al and Ti-B, by suing heptane as a grinding aid, each MA powder of the amorphous TiAl containing carbon and extremely fine compound TiB2 were prepared, and subsequently the true density sintering by the hot isostatic pressing (HIP) was performed, and by doing these, the preparation of TiAl/TiB2 system composite material with a high composite ratio of TiO2 was tried. Consequently, by the MA treatment of the mixed powder of Ti and B for more than 50 hours, the compound powder of TiB2 mixed with TiB could be prepared, and its hardness has shown the maximum value Hmv=l200 with a composition of TiAl/25 mol % TiB2. 14 refs., 10 figs., 2 tabs.

Manufacturing of small scale W monoblock mockups by hot radial pressing

International Nuclear Information System (INIS)

Visca, Eliseo; Testani, C.; Libera, S.; Sacchetti, M.

2003-01-01

In the frame of the European Technology R and D programme for International thermonuclear experimental reactor (ITER) and in the area of high heat flux plasma facing components (HHFC), representative small-scale mock-ups were manufactured and tested to compare different concepts and joining technologies (i.e. active brazing, hot isostatic pressing (HIPping), diffusion bonding, etc.). On the basis of the results obtained by thermal fatigue tests, the monoblock concept resulted to be the most robust one, particularly when the HIPping manufacturing technology is used. Within this programme, ENEA developed an alternative technique for manufacturing plasma-facing components with a monoblock geometry of the ITER machine. The basic idea of this technique, named hot radial pressing (HRP), is to perform a radial diffusion bonding between the cooling tube and the armour tile by pressurising the internal tube only and by keeping the process parameters within the range in which the thermo-mechanical properties of the copper alloys are not yet degraded. The HRP is performed by a standard furnace, in which only a section of the canister is heated. The manufacturing procedure and the results of the screening and fatigue thermal tests performed on the ENEA mock-ups are reported in this paper

One step HIP canning of powder metallurgy composites

Science.gov (United States)

Juhas, John J. (Inventor)

1990-01-01

A single step is relied on in the canning process for hot isostatic pressing (HIP) powder metallurgy composites. The binders are totally removed while the HIP can of compatible refractory metal is sealed at high vacuum and temperature. This eliminates outgassing during hot isostatic pressing.

Cold Isostatic-Pressured Silver Nanowire Electrodes for Flexible Organic Solar Cells via Room-Temperature Processes.

Science.gov (United States)

Seo, Ji Hoon; Hwang, Inchan; Um, Han-Don; Lee, Sojeong; Lee, Kangmin; Park, Jeonghwan; Shin, Hyeonoh; Kwon, Tae-Hyuk; Kang, Seok Ju; Seo, Kwanyong

2017-08-01

Transparent conducting electrodes (TCEs) are considered to be an essential structural component of flexible organic solar cells (FOSCs). Silver nanowire (AgNW) electrodes are widely used as TCEs owing to their excellent electrical and optical properties. The fabrication of AgNW electrodes has faced challenges in terms of forming large uniform interconnected networks so that high conductivity and reproducibility can be achieved. In this study, a simple method for creating an intimate contact between AgNWs that uses cold isostatic pressing (CIP) is demonstrated. This method increases the conductivity of the AgNW electrodes, which enables the fabrication of high-efficiency inverted FOSCs that have a power conversion efficiency of 8.75% on flexible polyethylene terephthalate with no short circuiting occurring as the CIP process minimizes the surface roughness of the AgNW electrode. This allows to achieve 100% manufacturing yield of FOSCs. Furthermore, these highly efficient FOSCs are proven to only be 2.4% less efficient even for an extreme bending radius of R ≈ 1.5 mm, compared with initial efficiency. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Absolute sea levels and isostatic changes of the eastern North Sea to central Baltic region during the last 900 years

DEFF Research Database (Denmark)

Hansen, Jens Morten; Aagaard, Troels; Binderup, Merete

2012-01-01

that ice-cap growth can be faster than ice-cap melting. By comparison with 29 long-term tide gauge measurements of the region we show that the isostatic implications of the sea-level curve are in nearly perfect agreement with Peltier's global isostatic VM2 model (applied by IPCC and PSMSL) and yield a 3...

Isostatic model for the Tharsis province, Mars

International Nuclear Information System (INIS)

Sleep, N.H.; Phillips, R.J.

1979-01-01

A crust-upper mantle configuration is proposed for the Tharsis province of Mars which is isostatic and satisfies the observed gravity data. The model is that of a low density upper mantle compensating loads at both the surface and crust-mantle boundary. Solutions are found for lithospheric thickness greater than about 300 km, for which the stress differences are less than 750 bars. This model for Tharsis is similar to the compensation mechanism under the Basin and Range province of the western United States. These provinces also compare favorably in the sense that they are both elevated regions of extensional tectonics and extensive volcanism

Bibliography on Hot Isostatic Pressing (HIP) Technology

Science.gov (United States)

1992-11-01

Nimonic API, Rene’ 77 2. MA753, IN-853 7 3. C-103,WC-103 4. Alloy 454, PWA 1480 5. Mar- M250 , Maraging (250) 6. Rene 150, PA 101 (low C) 7. Inconel 718...Pressure Welding Parameters Bryant. W. A. Weld J 54 (12), 433-S-435-S, 1975 ( AD-DI02 316 Key Words: AISI 4340. MAR- M250 . AISI 1020, 9Ni-4Co steel. Inconel...creep rupture. hot corrosion, oxidation, grain size, thermomechanical treatment MAR- M250 1. Microstructures and Mechanical Properties of HIP

Prediction of Pressing Quality for Press-Fit Assembly Based on Press-Fit Curve and Maximum Press-Mounting Force

Directory of Open Access Journals (Sweden)

Bo You

2015-01-01

Full Text Available In order to predict pressing quality of precision press-fit assembly, press-fit curves and maximum press-mounting force of press-fit assemblies were investigated by finite element analysis (FEA. The analysis was based on a 3D Solidworks model using the real dimensions of the microparts and the subsequent FEA model that was built using ANSYS Workbench. The press-fit process could thus be simulated on the basis of static structure analysis. To verify the FEA results, experiments were carried out using a press-mounting apparatus. The results show that the press-fit curves obtained by FEA agree closely with the curves obtained using the experimental method. In addition, the maximum press-mounting force calculated by FEA agrees with that obtained by the experimental method, with the maximum deviation being 4.6%, a value that can be tolerated. The comparison shows that the press-fit curve and max press-mounting force calculated by FEA can be used for predicting the pressing quality during precision press-fit assembly.

Isostatic and Decompensative Gravity Anomalies of the Arabian Plate and Surrounding Regions: a Key for the Crustal Structure

Science.gov (United States)

Kaban, M. K.; El Khrepy, S.; Al-Arifi, N. S.

2016-12-01

The isostatic anomalies are often considered as one of the most useful correction of the gravity field for investigation of the upper crust structure in many practical applications. By applying this correction, a substantial part of the effect of deep density heterogeneity, which dominates in the Bouguer gravity anomaly, can be removed. With this approach, it is not even necessary to know the deep density structure of the crust and upper mantle in details; it is sufficient to prescribe some type of compensation (regional vs. local) and a compensation depth. However, even when all the parameters are chosen correctly, this reduction of the gravity field does not show the full gravity effect of unknown anomalies in the crust. The last ones should be also compensated to some extent; therefore their impact is substantially reduced by the isostatic compensation. Long ago (Cordell et al., 1991), it was suggested a so-called decompensative correction of the isostatic anomalies, which provides a possibility to separate these effects. However, the decompensative correction is very sensitive to the parameters of the compensation scheme. In the present study we analyse the ways to choose these parameters and extend this approach by assuming a possibility for the regional compensation via elastic deformations of the lithosphere. Based on this technique, we estimate the isostatic and decompensative anomalies for the Arabian plate and surrounding regions. The parameters of the isostatic model are chosen based on previous studies. It was demonstrated that the decompensative correction is very significant at the mid-range wavelengths and may exceed 100 mGal, therefore ignoring this effect would lead to wrong conclusions about the upper crust structure. The total amplitude of the decompensative anomalies reaches ±250 mGal, evidencing for both, large density anomalies of the upper crust (including sediments) and strong isostatic disturbances of the lithosphere. These results improve

Towards Constraining Glacial Isostatic Adjustment in Greenland Using ICESat and GPS Observations

DEFF Research Database (Denmark)

Nielsen, Karina; Sørensen, Louise Sandberg; Khan, Shfaqat Abbas

2014-01-01

Constraining glacial isostatic adjustment (GIA) i.e. the Earth’s viscoelastic response to past ice changes, is an important task, because GIA is a significant correction in gravity-based ice sheet mass balance estimates. Here, we investigate how temporal variations in the observed and modeled cru...

Extensional Fault Evolution and its Flexural Isostatic Response During Iberia-Newfoundland Rifted Margin Formation

Science.gov (United States)

Gómez-Romeu, J.; Kusznir, N.; Manatschal, G.; Roberts, A.

2017-12-01

During the formation of magma-poor rifted margins, upper lithosphere thinning and stretching is achieved by extensional faulting, however, there is still debate and uncertainty how faults evolve during rifting leading to breakup. Seismic data provides an image of the present-day structural and stratigraphic configuration and thus initial fault geometry is unknown. To understand the geometric evolution of extensional faults at rifted margins it is extremely important to also consider the flexural response of the lithosphere produced by fault displacement resulting in footwall uplift and hangingwall subsidence. We investigate how the flexural isostatic response to extensional faulting controls the structural development of rifted margins. To achieve our aim, we use a kinematic forward model (RIFTER) which incorporates the flexural isostatic response to extensional faulting, crustal thinning, lithosphere thermal loads, sedimentation and erosion. Inputs for RIFTER are derived from seismic reflection interpretation and outputs of RIFTER are the prediction of the structural and stratigraphic consequences of recursive sequential faulting and sedimentation. Using RIFTER we model the simultaneous tectonic development of the Iberia-Newfoundland conjugate rifted margins along the ISE01-SCREECH1 and TGS/LG12-SCREECH2 seismic lines. We quantitatively test and calibrate the model against observed target data restored to breakup time. Two quantitative methods are used to obtain this target data: (i) gravity anomaly inversion which predicts Moho depth and continental lithosphere thinning and (ii) reverse post-rift subsidence modelling to give water and Moho depths at breakup time. We show that extensional faulting occurs on steep ( 60°) normal faults in both proximal and distal parts of rifted margins. Extensional faults together with their flexural isostatic response produce not only sub-horizontal exhumed footwall surfaces (i.e. the rolling hinge model) and highly rotated (60�

ZrC Ceramics Prepared by Self-propagating High-temperature Synthesis/Single Action Pressing

Directory of Open Access Journals (Sweden)

CHENG Yong

2017-01-01

Full Text Available ZrC ceramics were prepared by mechanical axial compression of self-propagating high-temperature synthesis/single action pressing (SHS/SAP.The effects of pressure on microstructure and densification of the products,as well as the relationship between displacement/variation of the load curve and SHS reaction,were studied.The structure and properties of the products were investigated by XRD and SEM.In addition,the density was measured by the drain away liquid method.Meanwhile,universal testing machine was used to record the displacement and load curve alternations.The results indicate that products are mainly composed of ZrC phase,the process of exhaust are accelerated as the increasing of pressure as well,leading to the smaller size of porosity and crystal particles.Density manifested as an increasing pattern by the elevated pressure with no longer change at 80MPa.Due to the strong attenuation of pressure at the peak of temperature,the density of the production is only 65.7% in 120MPa.The end point of the SHS reaction and the plastic time of the products can be monitored by displacement and load curve.The results provide evidence for the application of self-propagating high-temperature synthesis/pseudo-hot isostatic pressing to further improve the density of ceramics.

Interface strength measurement of tungsten coatings on F82H substrates

International Nuclear Information System (INIS)

Kim, Hyoungil; El-Awady, Jaafar; Gupta, Vijay; Ghoniem, Nasr; Sharafat, Shahram

2009-01-01

In the current work, hot isostatic pressing is adopted to deposit tungsten coatings on F82H substrates. The interface strength of the W/F82H samples is measured using the Laser Spallation technique and the microstructure is analyzed to determine the strength of the coating. Finally, the failure mechanisms of the hot isostatic pressing versus vacuum plasma spraying tungsten coatings and their different failure strengths are compared. It is concluded that the hot isostatic pressing process ensures a good adhesion for the W/F82H interface while the vacuum plasma spraying process results in relatively lower failure strength for the W-coating itself due to the high porosity in the coating.

ISOSTATICALLY DISTURBED TERRAIN OF NORTHWESTERN ANDES MOUNTAINS FROM SPECTRALLY CORRELATED FREE-AIR AND GRAVITY TERRAIN DATA

Directory of Open Access Journals (Sweden)

Hernández P Orlando

2006-12-01

Full Text Available Recently revised models on global tectonics describe the convergence of the North Andes, Nazca, Caribbean and South American Plates and their seismicity, volcanism, active faulting and extreme
topography. The current plate boundaries of the area are mainly interpreted from volcanic and seismic datasets with variable confidence levels. New insights on the isostatic state and plate boundaries of
the northwestern Andes Mountains can be obtained from the spectral analysis of recently available gravity and topography data.
Isostatically disturbed terrain produces free-air anomalies that are highly correlated with the gravity effects of the terrain. The terrain gravity effects (TGE and free air gravity anomalies (FAGA of the
Andes mountains spectral correlation data confirms that these mountains are isostatically disturbed. Strong negative terrain-correlated FAGA along western South America and the Greater and Lesser Antilles are consistent with anomalously deepened mantle displaced by subducting oceanic plates.

Inversion of the compensated terrain gravity effects (CTGE reveals plate subduction systems with alternating shallower and steeper subduction angles. The gravity modeling highlights crustal
deformation from plate collision and subduction and other constraints on the tectonism of the plate boundary zones for the region.

Gas hydrate dissociation off Svalbard induced by isostatic rebound rather than global warming.

Science.gov (United States)

Wallmann, Klaus; Riedel, M; Hong, W L; Patton, H; Hubbard, A; Pape, T; Hsu, C W; Schmidt, C; Johnson, J E; Torres, M E; Andreassen, K; Berndt, C; Bohrmann, G

2018-01-08

Methane seepage from the upper continental slopes of Western Svalbard has previously been attributed to gas hydrate dissociation induced by anthropogenic warming of ambient bottom waters. Here we show that sediment cores drilled off Prins Karls Foreland contain freshwater from dissociating hydrates. However, our modeling indicates that the observed pore water freshening began around 8 ka BP when the rate of isostatic uplift outpaced eustatic sea-level rise. The resultant local shallowing and lowering of hydrostatic pressure forced gas hydrate dissociation and dissolved chloride depletions consistent with our geochemical analysis. Hence, we propose that hydrate dissociation was triggered by postglacial isostatic rebound rather than anthropogenic warming. Furthermore, we show that methane fluxes from dissociating hydrates were considerably smaller than present methane seepage rates implying that gas hydrates were not a major source of methane to the oceans, but rather acted as a dynamic seal, regulating methane release from deep geological reservoirs.

Isostatic compaction of beaker shaped bentonite blocks on the scale 1:4

Energy Technology Data Exchange (ETDEWEB)

Johannesson, Lars-Erik [Clay Technology AB, Lund (Sweden); Nord, Sven [Ifoe Ceramics AB, Bromoella (Sweden ); Pusch, Roland [Geodevelopment AB, Lund (Sweden); Sjoeblom, Rolf [AaF-Energikonsult AB, Stockholm (Sweden)

2000-09-01

The purpose of the present work is to test, on a scale of 1:4, the feasibility of manufacturing bentonite blocks by isostatic compaction for application as a buffer material in a repository for spent nuclear fuel. In order for the tests to be sensitive to any weaknesses of the method, the blocks were shaped as beakers. The scope included the following: 1. Preparation of powder: a. mixing of the bentonite and addition of water in predetermined amounts, b. sieving to remove any lumps generated; 2. Isostatic compaction: a. establishment of a separate laboratory for the handling of bentonite powder (weighing, mixing, filling, sampling and machining), b. development and design of equipment and procedures for compaction of bentonite to beaker-shaped specimens, c. compaction process operation, d. visual inspection; 3. Sampling and characterisation: a. extraction of samples from the blocks made, b. determination of water content, c. determination of density, d. determination of strain at maximum stress by means of bending tests, e. determination of tensile strength by means of bending tests, f. determination of geometries of the blocks prepared; 4. Post-treatment by means of machining: a. machining of blocks made, b. visual inspection; 5. Evaluation. The work went very smoothly. No significant obstacles or unexpected events were encountered. The conclusions are as follows: The conclusions drawn in this report from work on the (linear)scale of one to four are very relevant to the full scale. Mixing of bentonite powder as well as moistening can be carried out on a pilot scale with a good homogeneity and with maintained good quality of the press powder. The compaction of bentonite can be carried out in a similar manner to the present operation at Ifoe Ceramics AB. This implies a very efficient handling as well as a very efficient use of the time in the press which may account for a large proportion of the total cost. The blocks could readily be produced to reproducible

Microstructure and Mechanical Properties of Long Ti-6Al-4V Rods Additively Manufactured by Selective Electron Beam Melting Out of a Deep Powder Bed and the Effect of Subsequent Hot Isostatic Pressing

Science.gov (United States)

Lu, S. L.; Tang, H. P.; Ning, Y. P.; Liu, N.; StJohn, D. H.; Qian, M.

2015-09-01

An array of eight long Ti-6Al-4V rods (diameter: 12 mm; height: 300 mm) have been additively manufactured, vertically and perpendicular to the powder bed, by selective electron beam melting (SEBM). The purpose was to identify and understand the challenges of fabricating Ti-6Al-4V samples or parts from a deep powder bed (more than 200-mm deep) by SEBM and the necessity of applying post heat treatment. The resulting microstructure and mechanical properties of these Ti-6Al-4V rods were characterized along their building ( i.e., axial) direction by dividing each rod into three segments (top, middle, and bottom), both before ( i.e., as-built) and after hot isostatic pressing (HIP). The as-built microstructure of each rod was inhomogeneous; it was coarsest in the top segment, which showed a near equilibrium α- β lamellar structure, and finest in the bottom segment, which featured a non-equilibrium mixed structure. The tensile properties varied along the rod axis, especially the ductility, but all tensile properties met the requirements specified by ASTM F3001-14. HIP increased the relative density from 99.03 pct of the theoretical density (TD) to 99.90 pct TD and homogenized the microstructure thereby leading to highly consistent tensile properties along the rod axis. The temperature of the stainless steel substrate used in the powder bed was monitored. The as-built inhomogeneous microstructure is attributed to the temperature gradient in the deep powder bed. Post heat treatment is thus necessary for Ti-6Al-4V samples or parts manufactured from a deep powder bed by SEBM. This differs from the additive manufacturing of small samples or parts from a shallow powder bed (less than 100-mm deep) by SEBM.

Uncertainty in Greenland glacial isostatic adjustment

DEFF Research Database (Denmark)

Milne, G. A.; Lecavalier, B.; Kjeldsen, K. K.

It is well known that the interpretation of geodetic data in Greenland to constrain recent ice mass changes requires knowledge of isostatic land motion associated with past changes in the ice sheet. In this talk we will consider a variety of factors that limit how well the signal due to past mass...... of the GIA model on predictions of land motion and gravity changes. The sensitivity of model output to plausible variations in both depth-dependent and lateral viscosity structure will be considered. With respect to the ice model, we will compare the relative contributions of loading during key periods...... of the ice history with a focus on the past few thousand years. In particular, we will show predictions of contemporary land motion and gravity changes due to loading changes following the Little Ice Age computed using a new reconstruction of ice thickness changes based largely on empirical data. A primary...

Behaviour and damage of a superalloy prepared by hot isostatic compression

International Nuclear Information System (INIS)

Dubiez-Le-Goff, Sophie

2003-01-01

This work deals with the behavior and damage of Udimet 720 superalloy prepared by hot isostatic compression. This alloy is considered for manufacturing turbine disks of high temperature reactors (HTR). The material choice for HTR turbine disk depends on the following criteria: a good creep resistance until 700 C, a good behaviour under an helium impure atmosphere, a possible implementation under a disk of 1.5 m diameter. (author) [fr

Modification of low density polyethylene, isostatic polypropylene and their blends by gamma radiation

International Nuclear Information System (INIS)

Santos Rosa, D. dos

1991-01-01

The effects of the gamma radiation (of a 60 Co source), over low density polyethylene, isostatic polypropylene and their blends of low density polyethylene / polypropylene were studied. The structures modifications were attended by infrared spectrometry (IV), differential scanning calorimeter (DSC), strain-strain measurement, density measurement and scanning electron microscope (SEM). (author)

Isostatic Implications of Different Seismic and Gravity Derived Moho Depths for Antarctica

Science.gov (United States)

Ferraccioli, F.; Pappa, F.; Ebbing, J.

2017-12-01

Several studies with different methods have been performed to investigate the lithospheric structure of Antarctica, in particular the Moho as the crust-mantle boundary. Yet, seismological surveys are regionally limited or suffer from sparse station coverage due to the remoteness and size of the continent. On the other hand, gravity studies are inherently ambiguous and therefore not able to determine both the geometry and the density contrast of the Moho. Existing Moho depth models for Antarctica show large discrepancies, even among different seismological methods, but all the more between seismological and gravity models. As a first step towards a possible reconcilement, we perform non-linear gravity inversions with simultaneous consideration of seismological data. Depending on the seismological input data, different depths and density contrasts yield the best fit. The results, however, are not in line with the pure seismological models. Subsequently, we compute simple Airy-isostatic Moho depth models and evaluate these together with multiple Moho models from previous studies in terms of their gravitational signal, applying different values for the density contrast. The models' responses are checked against observational data: vertical gravity at 50 km altitude from the spherical harmonics expansion model GOCO05s, and the gravity gradient tensor at 225 km altitude from the GOCE gravity gradient grids. While the gravity responses from the seismological models show strong disagreements with the data, the Airy-isostatic models fit better. Yet, differences of up to 10 km in depth exist between the isostatic and the gravity-inverted Moho models. From these differences in vertical gravity, in the gravity gradients and in Moho depth, we identify regions where a simple density contrast is not sufficient to explain the observed gravitational field. We conclude that lateral and vertical density variations must be considered, which might originate from high-density lower

The Influence of Sediment Isostatic Adjustment on Sea Level Change and Land Motion Along the U.S. Gulf Coast

Science.gov (United States)

Kuchar, Joseph; Milne, Glenn; Wolstencroft, Martin; Love, Ryan; Tarasov, Lev; Hijma, Marc

2018-01-01

Sea level rise presents a hazard for coastal populations, and the Mississippi Delta (MD) is a region particularly at risk due to the high rates of land subsidence. We apply a gravitationally self-consistent model of glacial and sediment isostatic adjustment (SIA) along with a realistic sediment load reconstruction in this region for the first time to determine isostatic contributions to relative sea level (RSL) and land motion. We determine optimal model parameters (Earth rheology and ice history) using a new high-quality compaction-free sea level indicator database. Using the optimal model parameters, we show that SIA can lower predicted RSL in the MD area by several meters over the Holocene and so should be taken into account when modeling these data. We compare modeled contemporary rates of vertical land motion with those inferred using GPS. This comparison indicates that isostatic processes can explain the majority of the observed vertical land motion north of latitude 30.7°N, where subsidence rates average about 1 mm/yr; however, subsidence south of this latitude shows large data-model discrepancies of greater than 3 mm/yr, indicating the importance of nonisostatic processes. This discrepancy extends to contemporary RSL change, where we find that the SIA contribution in the Delta is on the order of 10-1 mm/yr. We provide estimates of the isostatic contributions to 20th and 21st century sea level rates at Gulf Coast Permanent Service for Mean Sea Level tide gauge locations as well as vertical and horizontal land motion at GPS station locations near the MD.

Isostatic gravity map of the Monterey 30 x 60 minute quadrangle and adjacent areas, California

Science.gov (United States)

Langenheim, V.E.; Stiles, S.R.; Jachens, R.C.

2002-01-01

The digital dataset consists of one file (monterey_100k.iso) containing 2,385 gravity stations. The file, monterey_100k.iso, contains the principal facts of the gravity stations, with one point coded per line. The format of the data is described below. Each gravity station has a station name, location (latitude and longitude, NAD27 projection), elevation, and an observed gravity reading. The data are on the IGSN71 datum and the reference ellipsoid is the Geodetic Reference System 1967 (GRS67). The free-air gravity anomalies were calculated using standard formulas (Telford and others, 1976). The Bouguer, curvature, and terrain corrections were applied to the free-air anomaly at each station to determine the complete Bouguer gravity anomalies at a reduction density of 2.67 g/cc. An isostatic correction was then applied to remove the long-wavelength effect of deep crustal and/or upper mantle masses that isostatically support regional topography.

Titanium Brazing for Structures and Survivability

Science.gov (United States)

2007-05-01

first method ( Weld +HIP) was a tungsten inert gas ( TIG ) weld around the exterior of the Ti- 6Al-4V blocks followed by hot isostatic pressing (HIP) at...beam welding plus hot isostatic pressing (E-beam+HIP) process in the encapsulation of a ceramic within a titanium structure. The testing of the...different joining methods highlighted some definite candidates for the replacement of the E-beam+HIP process , such as the Weld +HIP, and demonstrated

Nanoindentation hardness of hot-pressed boron suboxide

International Nuclear Information System (INIS)

Machaka, Ronald; Derry, Trevor E.; Sigalas, Iakovos

2011-01-01

Highlights: → The load-displacement indentation response of hot-pressed B 6 O is measured and analysed. → The nanoindentation hardness of hot-pressed boron suboxide is reported. → An approach is developed to simulate multi-cycling loading load-displacement curves. → A comprehensive model inter-comparison study of the ISE in hot-pressed B 6 O is also presented. → The fractal dimension is a better measure of ISE than the Meyer's index. - Abstract: The existence of the indentation size effect implies the absence of a single hardness value for the material under investigation especially at low applied loads. In this paper we present an investigation of the indentation size dependence behaviour of nanoindentation hardness in boron suboxide ceramic compacts prepared by uniaxial hot-pressing. Berkovich nanohardness indentations were conducted and analyzed accordingly. In addition to the ordinary Oliver and Pharr method of nanoindentation data analysis, a quantitative approach for the loading curve analysis is proposed. Using the proposed approach, the description and characterization of the observed indentation size effect through the application of the Meyer's law, and the classical and the modified proportional specimen resistance models as well as the multi-fractal scaling law was conducted and is reported. The load-independent hardness values deduced from our quantitative approach are comparable to the results calculated with conventional methods, especially with the multi-fractal scaling law.

Nanoindentation hardness of hot-pressed boron suboxide

Energy Technology Data Exchange (ETDEWEB)

Machaka, Ronald, E-mail: Ronald.Machaka@wits.ac.za [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Chemical and Metallurgical Engineering, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa); Derry, Trevor E. [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Physics, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa); Sigalas, Iakovos [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Chemical and Metallurgical Engineering, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa)

2011-07-15

Highlights: {yields} The load-displacement indentation response of hot-pressed B{sub 6}O is measured and analysed. {yields} The nanoindentation hardness of hot-pressed boron suboxide is reported. {yields} An approach is developed to simulate multi-cycling loading load-displacement curves. {yields} A comprehensive model inter-comparison study of the ISE in hot-pressed B{sub 6}O is also presented. {yields} The fractal dimension is a better measure of ISE than the Meyer's index. - Abstract: The existence of the indentation size effect implies the absence of a single hardness value for the material under investigation especially at low applied loads. In this paper we present an investigation of the indentation size dependence behaviour of nanoindentation hardness in boron suboxide ceramic compacts prepared by uniaxial hot-pressing. Berkovich nanohardness indentations were conducted and analyzed accordingly. In addition to the ordinary Oliver and Pharr method of nanoindentation data analysis, a quantitative approach for the loading curve analysis is proposed. Using the proposed approach, the description and characterization of the observed indentation size effect through the application of the Meyer's law, and the classical and the modified proportional specimen resistance models as well as the multi-fractal scaling law was conducted and is reported. The load-independent hardness values deduced from our quantitative approach are comparable to the results calculated with conventional methods, especially with the multi-fractal scaling law.

The role of the 2008 Mw 7.9 Wenchuan earthquake in topographic evolution: seismically induced landslides and the associated isostatic response

Science.gov (United States)

Ren, Z.; Zhang, Z.; Zhang, H.; Zheng, W.; Zhang, P. Z.

2017-12-01

The widely held understanding that reverse-faulting earthquakes play an important role in building mountains has been challenged by recent studies suggesting that co-seismic landslides of the 2008 Mw 7.9 Wenchuan earthquake led to a net co-seismic lowering of surface height. We use precise estimates of co-seismic landslide volumes to calculate the long-term isostatic response to landsliding during the 2008 Wenchuan earthquake. The total isostatic respond volume is 2.0 km3 which did not change much associated with thickness of Te, however, the distribution of the rebound changes associated with thickness of Te. The total co-seismic mass change could be 1.8 km3. The maximum isostatic response due to Wenchuan earthquake may have been as high as 0.9 meters in the highest Pengguan massif of the central Longmen Shan. We also find that the average net uplift is 0.16 meters within the total landslide region due to the Wenchuan earthquake. Our findings suggest that the local topographic evolution of the middle Longmen Shan region is closely related to repeated tectonic events such as the 2008 Wenchuan Earthquake.

Smashing WordPress Themes Making WordPress Beautiful

CERN Document Server

Hedengren, Thord Daniel

2011-01-01

The ultimate guide to WordPress Themes - one of the hottest topics on the web today WordPress is so much more than a blogging platform, and Smashing WordPress Themes teaches readers how to make it look any way they like - from a corporate site, to a photography gallery and moreWordPress is one of the hottest tools on the web today and is used by sites including The New York Times, Rolling Stone, flickr, CNN, NASA and of course Smashing MagazineBeautiful full colour throughout - web designers expect nothing lessSmashing Magazine will fully support this book by by promoting it through their webs

RELATIONSHIP BETWEEN COMPACTING PRESSURE AND CONDITIONS IN PRESSING CHAMBER DURING BIOMASS PRESSING

Directory of Open Access Journals (Sweden)

Peter Križan

2016-02-01

Full Text Available In this paper, we will present the impact of the conditions in pressing chambers during the pressing of wooden briquettes. The conditions in pressing chambers can significantly impact the resulting compacting pressure required for the pressing of briquettes. In the introduction, we show which parameters of the pressing chamber during pressing can impact the resulting compacting pressure. The experiment results which are shown in this paper described the detected impact of some important pressing chamber parameters. This experiment aims to detect the pressing chamber length impact and the impact of the way of pressing. By setting the pressing conditions, we will be able to achieve the suitable resulting compacting pressure with respect to the required final briquettes quality.

Sintering of ZrC by hot isostatic pressing (HIP) and spark plasma sintering (SPS). Effect of impurities

International Nuclear Information System (INIS)

Allemand, Alexandre; Le Flem - Dormeval, Marion; Guillard, Francois

2005-01-01

Carbides are generally used as structural materials for high temperature applications. Particularly, ZrC because of low activation, neutronic transparency, cubic structure (isotropic behaviour) and good thermal conductivity, is one of the candidates under consideration for structural materials in the core of new high temperature nuclear reactors (Generation IV). Just a few studies about densification of monolithic ZrC exist. They mainly involve natural sintering or hot pressing at high temperature (until 2700 deg. C). Unfortunately those processes induce grain growth and do not lead to fully densified ZrC. The aim of this study is to compare the characteristics and the properties of ZrC sintered by HIP and by SPS. Fully dense ZrC can be reached either by HIP or by SPS, grain size being more or less controlled. Microstructural observations and mechanical testing of several ZrC grades shows that powder impurities play an important role in the quality of the grain boundaries and consequently in the mechanical properties. In particular, the porosity falls from 17% to 3 % just by reducing the free carbon content in starting ZrC powder. The densification process of dense monolithic ZrC was improved by combining a HIP at 1600 deg. C (titanium canning) followed by a post-HIP at 1900 deg. C (no canning required). Four-point bending tests are in progress to confirm the improvement of fracture strength. (authors)

High Performance Transfer Press for Precision Manufacturing of Micro Metal Parts

DEFF Research Database (Denmark)

Mahshid, Rasoul

for this technology and are available already in the market. Similar to conventional forming processes, the presence of a handling system can significantly improve the efficiency of the technology towards building a high performance transfer press for micro forming technology. To examine this possibility...... for actuation principle and mechanical grippers based on self-centering and friction principles. This study introduced a methodology for the analysis and characterization of this transfer system on component level and system level. Laser interferometry was used in combination with analytical models to predict...... the positioning ability of the actuator in a static as well as dynamic mode. In combination with an analysis of the grippers, a full description of the transfer precision inside the forming press was obtained. The current research involved integration of a handling system into an existing developed micro press...

Results of intermediate-scale hot isostatic press can experiments

International Nuclear Information System (INIS)

Nelson, L.O.; Vinjamuri, K.

1995-05-01

Radioactive high-level waste (HLW) has been managed at the Idaho Chemical Processing Plant (ICPP) for a number of years. Since 1963, liquid HLW has been solidified into a granular solid (calcine). Presently, over 3,800 m 3 of calcine is stored in partially-underground stainless steel bins. Four intermediate- scale HLW can tests (two 6-in OD x 12-in tall and two 4-in OD x 7-in tall) are described and compared to small-scale HIP can tests (1- to 3-in OD x 1- to 4.5-in tall). The intermediate-scale HIP cans were loaded with a 70/30 calcine/frit blend and HIPped at an off-site facility at 1050 degrees C; and 20 ksi. The dimensions of two cans (4-in OD x 7-in tall) were monitored during the HIP cycle with eddy-current sensors. The sensor measurements indicated that can deformation occurs rapidly at 700 degrees C; after which, there is little additional can shrinkage. HIP cans were subjected to a number of analyses including calculation of the overall packing efficiency (56 to 59%), measurement of glass-ceramic (3.0 to 3.2 g/cc), 14-day MCC-1 leach testing (total mass loss rates 2 day), and scanning electron microscopy (SEM). Based on these analyses, the glass-ceramic material produced in intermediate-scale cans is similar to material produced in small-scale cans. No major scale-up problems were indicated. Based on the packing efficiency observed in intermediate- and small-scale tests, the overall packing efficiency of production-scale (24-in OD x 36- to 190-in tall) cans would be approximately 64% for a pre-HIP right-circular cylinder geometry. An efficiency of 64% would represent a volume reduction factor of 2.5 over a candidate glass waste prepared at 33 wt% waste loading

Development of Hot Isostatically Pressed Rene 95 Turbine Parts

Science.gov (United States)

1977-05-01

Jull 17 ,. " 1ENE’ 95 TURBINE PARTS~ 7. AUTHOR(e) CO(A RRNNME P.)Mathur aWJ. Bartos AJ-3C0V hae1 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM...200 mesh coff .,acts prepared in the autoclave at 20500F and the -60 mesh compact prepared by *1650 0F14 hours, 2000°1/1 hour/OQ, + 1400°F/16 hours/AC...Product Acceptance plans (Appendix- Ill); the Quality Control of General Elctric Company was-extended to establish procedures and- organization , to

Arc melting and homogenization of ZrC and ZrC + B alloys

Science.gov (United States)

Darolia, R.; Archbold, T. F.

1973-01-01

A description is given of the methods used to arc-melt and to homogenize near-stoichiometric ZrC and ZrC-boron alloys, giving attention to the oxygen contamination problem. The starting material for the carbide preparation was ZrC powder with an average particle size of 4.6 micron. Pellets weighing approximately 3 g each were prepared at room temperature from the powder by the use of an isostatic press operated at 50,000 psi. These pellets were individually melted in an arc furnace containing a static atmosphere of purified argon. A graphite resistance furnace was used for the homogenization process.

WordPress Bible

CERN Document Server

Brazell, Aaron

2010-01-01

The WordPress Bible provides a complete and thorough guide to the largest self hosted blogging tool. This guide starts by covering the basics of WordPress such as installing and the principles of blogging, marketing and social media interaction, but then quickly ramps the reader up to more intermediate to advanced level topics such as plugins, WordPress Loop, themes and templates, custom fields, caching, security and more. The WordPress Bible is the only complete resource one needs to learning WordPress from beginning to end.

Coil measurement data acquisition and curing press control system for SSC dipole magnet coils

International Nuclear Information System (INIS)

Dickey, C.E.

1989-03-01

A coil matching program, similar in theory to the methods used to match Tevatron coils, is being developed at Fermilab. Modulus of elasticity and absolute coil size will be determined at 18-inch intervals along the coils while in the coil curing press immediately following the curing process. A data acquisition system is under construction to automatically acquire and manage the large quantities of data that result. Data files will be transferred to Fermilab's VAX Cluster for long-term storage and actual coil matching. The data acquisition system will also provide the control algorithm for the curing press hydraulic system. A description of the SSC Curing Press Data Acquisition and Controls System will be reported. 20 figs

Spatio-spectral localization of isostatic coherence anisotropy in Australia and its relation to seismic anisotropy : Implications for lithopsheric deformation

NARCIS (Netherlands)

Simons, Frederik J.; Hilst, R.D. van der; Zuber, M.T.

2003-01-01

We investigate the two-dimensional (2-D) nature of the coherence between Bouguer gravity anomalies and topography on the Australian continent. The coherence function or isostatic response is commonly assumed to be isotropic. However, the fossilized strain field recorded by gravity anomalies and

The isostatic state of Mead crater

Science.gov (United States)

Banerdt, W. B.; Konopliv, A. S.; Rappaport, N. J.; Sjogren, W. L.; Grimm, R. E.; Ford, P. G.

1994-01-01

We have analyzed high-resolution Magellan Doppler tracking data over Mead crater, using both line-of-sight and spherical harmonic methods, and have found a negative gravity anomaly of about 4-5 mgal (at spacecraft altitude, 182 km). This is consistent with no isostatic compensation of the present topography; the uncertainty in the analysis allows perhaps as much as 30% compensation at shallow dpeths (approximately 25 km). This is similar to observations of large craters on Earth, which are not generally compensated, but contrasts with at least some lunar basins which are inferred to have large Moho uplifts and corresponding positive Bouguer anomalies. An uncompensated load of this size requires a lithosphere with an effective elastic lithosphere thickness greater than 30 km. In order for the crust-mantle boundary not to have participated in the deformation associated with the collapse of the transient cavity during the creation of the crater, the yield strength near the top of the mantle must have been significantly higher on Earth and Venus than on the Moon at the time of basin formation. This might be due to increased strength against frictional sliding at the higher confining pressures within the larger planets. Alternatively, the thinner crusts of Earth and Venus compared to that of the Moon may result in higher creep strength of the upper mantle at shallower depths.

Potential of high isostatic pressure and pulsed electric fields for the processing of potato and pea proteins:structural and techno-functional characterization in model solutions and plant tissue

OpenAIRE

Baier, Anne Kathrin

2016-01-01

The aim of this thesis was to evaluate the potential of high isostatic pressure and pulsed electric fields for the production of high quality plant proteins. Induced changes in protein solutions and plant tissue of potato and pea were analyzed by means of structural and techno-functional characterization as well as by investigation of diffusion and extractions procedures. The application of high isostatic pressure provides a gentle alternative to conventional heat preservation. Especially ...

WordPress for dummies

CERN Document Server

Sabin-Wilson, Lisa

2014-01-01

The bestselling WordPress guide, fully updated to cover the 2013 enhancements WordPress has millions of users, and this popular guide has sold more than 105,000 copies in its previous editions. With the newest releases of WordPress, author and WordPress expert Lisa Sabin-Wilson has completely updated the book to help you use and understand all the latest features. You'll learn about both the hosted WordPress.com version and the more flexible WordPress.org, which requires third-party hosting. Whether you're switching to WordPress from another blogging platform or just beginning to blog, you'll

The Social Theories of the press: journalism and society

Directory of Open Access Journals (Sweden)

Beatriz Marocco

2005-06-01

Full Text Available For a short period of time, between the end of the 19th century and the middle of the 20th, newspapers and journalists were under the spotlight as never before. However, the comprehensive reviews of the theories of the press do not acknowledge the thought of this period and its development into “the social theories of the press” (H. Hardt, 1979. This article is positioned in this gap of press studies, and it uses as a starting point the foucaultian description of the diff erent thresholds that establish the levels of discourse elaboration (Foucault, 1995. It aims at exploring the theoretical production that approximates German and American scholars such as Albert Schäffle (1831-1903; Karl Knies (1821-1898; Karl Bücher (1847-1930; Ferdinand Tönnies (1835-1936; Albion Small (1854-1926; Edward Ross (1856-1951; Max Weber (1864-1920; Robert Park (1864-1944 and Walter Lippmann (1889-1974, rescuing this production from the pre-history of the press to materialize evidence that this production coincides, in its external origin, with the modern newspaper practices, although there seemed to be no dependence between them at the time.

The Social Theories of the press: journalism and society

Directory of Open Access Journals (Sweden)

Beatriz Marocco

2011-02-01

Full Text Available For a short period of time, between the end of the 19th century and the middle of the 20th, newspapers and journalists were under the spotlight as never before. However, the comprehensive reviews of the theories of the press do not acknowledge the thought of this period and its development into “the social theories of the press” (H. Hardt, 1979. This article is positioned in this gap of press studies, and it uses as a starting point the foucaultian description of the diff erent thresholds that establish the levels of discourse elaboration (Foucault, 1995. It aims at exploring the theoretical production that approximates German and American scholars such as Albert Schäffle (1831-1903; Karl Knies (1821-1898; Karl Bücher (1847-1930; Ferdinand Tönnies (1835-1936; Albion Small (1854-1926; Edward Ross (1856-1951; Max Weber (1864-1920; Robert Park (1864-1944 and Walter Lippmann (1889-1974, rescuing this production from the pre-history of the press to materialize evidence that this production coincides, in its external origin, with the modern newspaper practices, although there seemed to be no dependence between them at the time.

Reciprocating pellet press

Science.gov (United States)

Jones, Charles W.

1981-04-07

A machine for pressing loose powder into pellets using a series of reciprocating motions has an interchangeable punch and die as its only accurately machines parts. The machine reciprocates horizontally between powder receiving and pressing positions. It reciprocates vertically to press, strip and release a pellet.

Press Advertising – Varieties and Sub-Varieties. Methods of Promoting the Press

OpenAIRE

Mikosz, Joanna

2016-01-01

In the text entitled “Press advertising – varieties and sub-varieties. Methods of promoting the press”, the author discusses press advertising, which is a fast developing mass-media phenomenon. Modernity has granted press advertising a high quality of print and paper, as well as Infinite possibilities of combining various promotional forms with the press. The author argues that press advertising is one of the best ways in which a company can communicate with the market. Its advantage is, abov...

WordPress For Dummies

CERN Document Server

Sabin-Wilson, Lisa

2011-01-01

The bestselling guide to WordPress, fully updated to help you get your blog going! Millions of bloggers rely on WordPress, the popular, free blogging platform. This guide covers all the features and improvements in the most up-to-date version of WordPress. Whether you are switching to WordPress from another blogging platform or just starting your first blog, you'll find the advice in this friendly guide gets you up to speed on both the free-hosted WordPress.com version and WordPress.org, which requires the purchase of web hosting services, and figure out which version is best for you. You'll b

Geologic and isostatic map of the Nenana Basin area, central Alaska

Science.gov (United States)

Frost, G.M.; Barnes, D.F.; Stanley, R.G.

2002-01-01

Introduction The Nenana Basin area is a prospective petroleum province in central Alaska, and this geologic and isostatic gravity map is part of a petroleum resource assessment of the area. The geology was compiled from published sources (Chapman and others, 1971, 1975a, 1975b, 1982; Chapman and Yeend, 1981; Csejtey and others, 1986; Jones and others, 1983; Pewe and others, 1966; Reed, 1961; and Weber and others, 1992), as shown on the index map (map sheet). Map units are organized and presented according to the scheme of lithotectonic terranes proposed by Jones and others (1987) and Silberling and Jones (1984); we recognize, however, that this terrane scheme is controversial and likely to be revised in the future. In some cases, we combined certain terranes because we were unable to match the terrane boundaries given by Jones and others (1987) and Silberling and Jones (1984) with specific faults shown on existing geologic maps. Postaccretion cover deposits represent overlap assemblages that depositionally overlie accreted terranes. Plutonic igneous rocks shown on this map include several plutons that are clearly postaccretionary, based on isotopic ages and (or) field relations. It is possible that some of the plutons predate accretion, but this has not been demonstrated. According to Jones and others (1982), the terranes in the area of our map were assembled during late Mesozoic or earliest Cenozoic time. The gravity contours are derived from data used in earlier compilations (Barnes, 1961, 1977; Hackett, 1981; Valin and others, 1991; Frost and Stanley, 1991) that are supplemented by some National Oceanic and Atmospheric Administration data along the Alaska Pipeline level line (W.E. Strange, written commun., 1980). The earlier compilations were used for simple Bouguer maps, prepared primarily by non-digital methods, and are superseded by this map. The present map is the result of digital processing that includes the 1967 Geodetic Reference System, the IGSN-71

WordPress Bible

CERN Document Server

Brazell, Aaron

2011-01-01

Get the latest word on the biggest self-hosted blogging tool on the marketWithin a week of the announcement of WordPress 3.0, it had been downloaded over a million times. Now you can get on the bandwagon of this popular open-source blogging tool with WordPress Bible, 2nd Edition. Whether you're a casual blogger or programming pro, this comprehensive guide covers the latest version of WordPress, from the basics through advanced application development. If you want to thoroughly learn WordPress, this is the book you need to succeed.Explores the principles of blogging, marketing, and social media

Treatment of cladding hulls by the HIPOW process

International Nuclear Information System (INIS)

Larker, H.T.; Tegman, R.

1981-01-01

The conditions for densifying and bonding Zircaloy cladding hulls from spent LWR fuel to blocks by the HIPOW (hot isostatic pressing of waste) process have been studied. Fully dense and mechanically strong blocks of Zircaloy can be made without additives at temperatures around 1000 0 C. A volume reduction of about seven times and surface area reduction of more than 300 times, compared to typical loose-filled cladding hulls remaining after the chop-leach operations in a reprocessing plant, can be obtained. A study of a possible process for industrial scale has been made. Handling under water can prevent any fire hazard in the preparation sequence. The use of a special hermetically sealed double-wall metal container encasing the hulls during the densification in the hot isostatic press virtually eliminates the problem of lasting contamination of this equipment, thus greatly simplifying service and maintenance. One hot isostatic press can serve a reprocessing line with an LWR fuel capacity of 800 tons/year. Fines (residues) from fuel dissolution and alpha-contaminated ashes from incinerated organic materials in the plant may also be incorporated in the Zircaloy blocks. Tritium can quantitatively be contained in these blocks

An Ensemble Analysis of Antarctic Glacial Isostatic Adjustment and Sea Level

Science.gov (United States)

Lecavalier, B.; Tarasov, L.

2016-12-01

Inferences of past ice sheet evolution that lack any uncertainty assessment (implicit or explicit), have little value. A developing technique for explicit uncertainty quantification of glacial systems is Bayesian calibration of models against large observational data-sets (Tarasov et al., 2012). The foundation for a Bayesian calibration of a 3D glacial systems model (GSM) for Antarctica has recently been completed (Briggs et al., 2013; 2014; Briggs and Tarasov, 2013). Bayesian calibration thoroughly samples model uncertainties against fits to observational data to generate a probability distribution for the Antarctic Ice Sheet deglaciation with explicit and well-defined confidence intervals. To have validity as a complete inference of past ice sheet evolution, Bayesian calibration requires a model that "brackets reality".Past work has shown the GSM to have likely inadequate range of grounding line migration in certain sectors as well as persistent ice thickness biases in topographically complex regions (Briggs et al., 2014). To advance towards full calibration, these deficiencies are being addressed through a number of model developments. The grounding line scheme has been revised (Pollard and DeConto, 2012), the horizontal resolution is increased to 20 km, and boundary conditions are updated. The basal drag representation now includes the sub-grid treatment of the thermo-mechanical impacts of high basal roughness. Parametric uncertainties in basal drag for regions that are presently marine have been re-evaluated. The impact of past changes in ocean temperature on sub ice shelf melt is explicitly incorporated in the current ocean forcing parametric scheme. Uncertainties in earth rheology are also probed to robustly quantify uncertainties affiliated with glacial isostatic adjustment. The ensemble analysis of the Antarctic glacial system provides dynamical bounds on past and present Antarctica glacial isostatic adjustment and sea level contributions. This research

Process description and plant design for preparing ceramic high-level waste forms

International Nuclear Information System (INIS)

Grantham, L.F.; McKisson, R.L.; Guon, J.; Flintoff, J.F.; McKenzie, D.E.

1983-01-01

The ceramics process flow diagram has been simplified and upgraded to utilize only two major processing steps - fluid-bed calcination and hot isostatic press consolidating. Full-scale fluid-bed calcination has been used at INEL to calcine high-level waste for 18 y; and a second-generation calciner, a fully remotely operated and maintained calciner that meets ALARA guidelines, started calcining high-level waste in 1982. Full-scale hot isostatic consolidation has been used by DOE and commercial enterprises to consolidate radioactive components and to encapsulate spent fuel elements for several years. With further development aimed at process integration and parametric optimization, the operating knowledge of full-scale demonstration of the key process steps should be rapidly adaptable to scale-up of the ceramic process to full plant size. Process flowsheets used to prepare ceramic and glass waste forms from defense and commercial high-level liquid waste are described. Preliminary layouts of process flow diagrams in a high-level processing canyon were prepared and used to estimate the preliminary cost of the plant to fabricate both waste forms. The estimated costs for using both options were compared for total waste management costs of SRP high-level liquid waste. Using our design, for both the ceramic and glass plant, capital and operating costs are essentially the same for both defense and commercial wastes, but total waste management costs are calculated to be significantly less for defense wastes using the ceramic option. It is concluded from this and other studies that the ceramic form may offer important advantages over glass in leach resistance, waste loading, density, and process flexibility. Preliminary economic calculations indicate that ceramics must be considered a leading candidate for the form to immobilize high-level wastes

News/Press Releases

Data.gov (United States)

Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

Head First WordPress

CERN Document Server

Siarto, Jeff

2010-01-01

Whether you're promoting your business or writing about your travel adventures, Head First WordPress will teach you not only how to make your blog look unique and attention-grabbing, but also how to dig into the more complex features of WordPress 3.0 to make your website work well, too. You'll learn how to move beyond the standard WordPress look and feel by customizing your blog with your own URL, templates, plugin functionality, and more. As you learn, you'll be working with real WordPress files: The book's website provides pre-fab WordPress themes to download and work with as you follow al

WordPress multisite administration

CERN Document Server

Longren, Tyler

2013-01-01

This is a simple, concise guide with a step-by-step approach, packed with screenshots and examples to set up and manage a network blog using WordPress.WordPress Multisite Administration is ideal for anyone wanting to familiarize themselves with WordPress Multisite. You'll need to know the basics about WordPress, and having at least a broad understanding of HTML, CSS, and PHP will help, but isn't required.

New isostatic mounting concept for a space born Three Mirror Anastigmat (TMA) on the Meteosat Third Generation Infrared Sounder Instrument (MTG-IRS)

Science.gov (United States)

Freudling, Maximilian; Klammer, Jesko; Lousberg, Gregory; Schumacher, Jean-Marc; Körner, Christian

2016-07-01

A novel isostatic mounting concept for a space born TMA of the Meteosat Third Generation Infrared Sounder is presented. The telescope is based on a light-weight all-aluminium design. The mounting concept accommodates the telescope onto a Carbon-Fiber-Reinforced Polymer (CRFP) structure. This design copes with the high CTE mismatch without introducing high stresses into the telescope structure. Furthermore a Line of Sight stability of a few microrads under geostationary orbit conditions is provided. The design operates with full performance at a temperature 20K below the temperature of the CFRP structure and 20K below the integration temperature. The mounting will sustain launch loads of 47g. This paper will provide the design of the Back Telescope Assembly (BTA) isostatic mounting and will summarise the consolidated technical baseline reached following a successful Preliminary Design Review (PDR).

High temperature synthesis of ceramic composition by directed reaction of molten titanium or zirconium with boron carbide

International Nuclear Information System (INIS)

Johnson, W.B.

1990-01-01

Alternative methods of producing ceramics and ceramic composites include sintering, hot pressing and more recently hot isostatic pressing (HIP) and self-propagating high temperature synthesis (SHS). Though each of these techniques has its advantages, each suffers from several restrictions as well. Sintering may require long times at high temperatures and for most materials requires sintering aids to get full density. These additives can, and generally do, change (often degrade) the properties of the ceramic. Hot pressing and hot isostatic pressing are convenient methods to quickly prepare samples of some materials to full density, but generally are expensive and may damage some types of reinforcements during densification. This paper focuses on the preparation and processing of composites prepared by the directed reaction of molten titanium or zirconium with boron carbide. Advantages and disadvantages of this approach when compared to traditional methods are discussed, with reference to specific examples. Examples of microstructure are properties of these materials are reported

Worldwide complete spherical Bouguer and isostatic anomaly maps

Science.gov (United States)

Bonvalot, S.; Balmino, G.; Briais, A.; Peyrefitte, A.; Vales, N.; Biancale, R.; Gabalda, G.; Reinquin, F.

2011-12-01

We present here a set of digital maps of the Earth's gravity anomalies (surface "free air", Bouguer and isostatic), computed at Bureau Gravimetric International (BGI) as a contribution to the Global Geodetic Observing Systems (GGOS) and to the global geophysical maps published by the Commission for the Geological Map of the World (CGMW). The free air and Bouguer anomaly concept is extensively used in geophysical interpretation to investigate the density distributions in the Earth's interior. Complete Bouguer anomalies (including terrain effects) are usually computed at regional scales by integrating the gravity attraction of topography elements over and beyond a given area (under planar or spherical approximations). Here, we developed and applied a worldwide spherical approach aimed to provide a set of homogeneous and high resolution gravity anomaly maps and grids computed at the Earth's surface, taking into account a realistic Earth model and reconciling geophysical and geodetic definitions of gravity anomalies. This first version (1.0) has been computed by spherical harmonics analysis / synthesis of the Earth's topography-bathymetry up to degree 10800. The detailed theory of the spherical harmonics approach is given in Balmino et al., (Journal of Geodesy, submitted). The Bouguer and terrain corrections have thus been computed in spherical geometry at 1'x1' resolution using the ETOPO1 topography/bathymetry, ice surface and bedrock models from the NOAA (National Oceanic and Atmospheric Administration) and taking into account precise characteristics (boundaries and densities) of major lakes, inner seas, polar caps and of land areas below sea level. Isostatic corrections have been computed according to the Airy Heiskanen model in spherical geometry for a constant depth of compensation of 30km. The gravity information given here is provided by the Earth Geopotential Model (EGM2008), developed at degree 2160 by the National Geospatial Intelligence Agency (NGA) (Pavlis

The Global University Press

Science.gov (United States)

Dougherty, Peter J.

2012-01-01

The modern world's understanding of American university press has long been shaped by university-press books. American university-press books are good international advertisements for the universities whose logos grace their spines. The growth of transnational scholarship and the expansion of digital communications networks are converging in ways…

Additively Manufactured, Net Shape Powder Metallurgy Cans for Valves Used in Energy Production

Energy Technology Data Exchange (ETDEWEB)

Peter, William H. [ORNL; Gandy, David [Electric Power Research Institute (EPRI); Lannom, Robert [Oak Ridge National Laboratory (ORNL)

2018-01-01

This CRADA NFE-14-05241 was conducted as a Technical Collaboration project within the Oak Ridge National Laboratory (ORNL) Manufacturing Demonstration Facility (MDF) sponsored by the US Department of Energy Advanced Manufacturing Office (CPS Agreement Number 24761). Opportunities for MDF technical collaborations are listed in the announcement “Manufacturing Demonstration Facility Technology Collaborations for US Manufacturers in Advanced Manufacturing and Materials Technologies” posted at http://web.ornl.gov/sci/manufacturing/docs/FBO-ORNL-MDF-2013-2.pdf. The goal of technical collaborations is to engage industry partners to participate in short-term, collaborative projects within the Manufacturing Demonstration Facility (MDF) to assess applicability and of new energy efficient manufacturing technologies. Research sponsored by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, under contract DE-AC05-00OR22725 with UT-Battelle, LLC.ORNL would like to acknowledge the leadership of EPRI in pulling together the extensive team and managing the execution of the project. In addition, ORNL would like to acknowledge the other contributions of the team members associated with this project. Quintus provided time, access, expertise, and labor of their hydro forming capabilities to evaluate both conventional and additively manufactured tools through this process. Crane ChemPharma Energy provided guidance and information on valve geometries. Carpenter Powder Products was involved with the team providing information on powder processing as it pertains to the canning and hot isostatic pressing of powder. on providing powder and knowledge as it pertains to powder supply for hot isostatic pressing; they also provided powder for the test trials by the industrial team. Bodycote provided guidance on hot isostatic pressing and can requirements. They were also responsible for the hot isostatic pressing of the test valve

Hot-pressed geopolymer

DEFF Research Database (Denmark)

Ranjbar, Navid; Mehrali, Mohammad; Maheri, Mahmoud R.

2017-01-01

This research explores the use of simultaneous heating and pressing techniques in order to enhance the mechanical properties of fly ash (FA) based geopolymer under relatively low temperature conditions to ensure minimum-porosity. Four effective parameters of pressing force, alkali activator...

Change of Pressing Chamber Conicalness at Briquetting Process in Briquetting Machine Pressing Chamber

Directory of Open Access Journals (Sweden)

Peter Križan

2012-01-01

Full Text Available In this paper, we will present the impact of the conical shape of a pressing chamber, an important structural parameter. Besides the known impact of the technological parameters of pressing chambers, it is also very important to pay attention to their structural parameters. In the introduction, we present a theoretical analysis of pressing chamber conicalness. An experiment aimed at detecting this impact was performed at our institute, and it showed that increasing the conicalness of a pressing chamber improves the quality of the final briquettes. The conicalness of the pressing chamber has a significanteffect on the final briquette quality and on the construction of briquetting machines. The experimental findings presented here show the importance of this parameter in the briquetting process.

Addressing Machining Issues for the Intermetallic Compound 60-NITINOL

Science.gov (United States)

Stanford, Malcolm K.; Wozniak, Walter A.; McCue, Terry R.

2012-01-01

60-NITINOL (60 wt.% Ni - 40 wt.% Ti) is being studied as a material for advanced aerospace components. Frequent wire breakage during electrical-discharge machining of this material was investigated. The studied material was fabricated from hot isostatically pressed 60-NITINOL powder obtained through a commercial source. Bulk chemical analysis of the material showed that the composition was nominal but had relatively high levels of certain impurities, including Al and O. It was later determined that Al2O3 particles had contaminated the material during the hot isostatic pressing procedure and that these particles were the most likely cause of the wire breakage. The results of this investigation highlight the importance of material cleanliness to its further implementation.

Teach yourself visually WordPress

CERN Document Server

Majure, Janet

2012-01-01

Get your blog up and running with the latest version of WordPress WordPress is one of the most popular, easy-to-use blogging platforms and allows you to create a dynamic and engaging blog, even if you have no programming skills or experience. Ideal for the visual learner, Teach Yourself VISUALLY WordPress, Second Edition introduces you to the exciting possibilities of the newest version of WordPress and helps you get started, step by step, with creating and setting up a WordPress site. Author and experienced WordPress user Janet Majure shares advice, insight, and best practices for taking full

Moho geometry gravity inversion experiment (MoGGIE): A refined model of the Australian Moho, and its tectonic and isostatic implications

Science.gov (United States)

Aitken, Alan R. A.

2010-08-01

At the continent-scale, models of Moho depth based on seismic estimates alone can be inadequate due to irregular or sparse data. Gravity-based Moho modelling provides better coverage, however, the methods used are typically hampered by an inability to explicitly honour seismic constraints and are also limited by over simplistic model conditions, e.g. laterally-homogenous layering. I present a new method to generate a continent-scale Moho model, based on the constrained inversion of free-air gravity data. This method explicitly honours seismic Moho estimates and accounts for a laterally heterogeneous crust and mantle. Resolution and sensitivity testing shows that, for wavelengths greater than 200 km, crustal density and Moho depth are recovered with reasonable accuracy, ± 30 kg m - 3 and ± 3 km respectively. MoGGIE uses a six layer model incorporating ocean, sedimentary basin, upper crust, lower/oceanic crust, eclogitised crust and mantle. Inversion variables were the density of the crustal layers, constrained by a standard density model, and the depths to intra-crustal boundaries and the Moho, constrained by 230 seismic depth estimates. The results demonstrate that a balanced approach to seismically-constrained gravity inversion has the capability to generate detailed and well-constrained models of the Moho and crustal density at the continent-scale. For Australia, this is a clear improvement on the sparse and irregular resolution of the Moho provided by seismic estimates of crustal thickness, which fail to resolve short-wavelength features. Newly defined tectonic features include extensive magmatic underplates, crustal-scale shear zones, and the boundaries between tectonic blocks. Isostatic analysis reveals that little of the continent is close to isostatic equilibrium, with isostatic disequilibria preserved at multiple scales, from hundreds of kilometres to the entire continent. These disequilibria are interpreted to indicate long-wavelength flexure of highly

Pratiques discursives et enjeux du pathos dans la présentation de l’Intifada al-Aqsa par la presse écrite en France Discursive Practices and the Stakes of Pathos in the Presentation of the Al-Aqsa Intifada in the French Press

Directory of Open Access Journals (Sweden)

Claire Sukiennik

2008-09-01

Full Text Available Mon étude porte sur les formes de mise en scène pratiquées par le discours qui construit les effets de pathos, et plus particulièrement sur la pitié et l’appel à la pitié. Mon cadre de recherche se limite à la mise en mots de l’Intifada al-Aqsa dans la presse écrite française. L’Intifada a éclaté en Israël et dans les « territoires occupés » en septembre 2000. Je me propose de problématiser ici la question paradoxale de la contribution au pathos de trois effets d’objectivité notoires : la citation ou le discours rapporté, les indications chiffrées et quelques effets de réel notoires, tels que les descriptions de paysages et les portraits de protagonistes palestiniens et israéliens. Il n’est pas rare en effet que les auteurs des articles de mon corpus utilisent l’instrument de la compassion en tant que procédé argumentatif alors que la déontologie de l’écriture de presse présente le devoir de neutralité rationnelle comme une obligation fondamentale.My study is based on the patterns of discourse which produce emotion and more particularly pity and the appeal to pity. My research is limited to the verbal description of Al-Aqsa Intifada in the French press, in Israel and in the “Occupied Territories” during September 2000. My purpose is to show how three effects of objectivity, namely quotation or direct speech, the appeal to numbers and some effects of reality such as the descriptions of landscapes and the portrayal of Palestinian and Israeli protagonists, actually contribute to the production of pathos. I will show that contrary to the code of ethics of the written press, which consists of presenting rational neutrality as a formal obligation of the press, compassion as an argumentative means is quite frequently used by the authors of the articles in question.

Near net shape of powder metallurgy rhenium parts

International Nuclear Information System (INIS)

Leonhardt, T.; Downs, J.

2001-01-01

In this paper, a description of the stages of processing necessary to produce a near-net shape (NNS) powder metallurgy (PM) rhenium component through the use of cold isostatic pressing (CIP) to form a complex shape will be explained. This method was primarily developed for the production of the 440 N and 490 N liquid apogee engine combustion chambers used in satellite positioning systems. The CIP to NNS process has been used in the manufacture and production of other rhenium aerospace components as well. Cold isostatic pressing (CIP) to a near net shape utilizing a one or two-part mandrel greatly reduces the quantity of rhenium required to produce the component, and also significantly reduces the number of secondary machining operations necessary to complete the manufacturing process. Further, the developments in near-net shape powder metallurgy rhenium manufacturing techniques have generated significant savings in the area of both time and budget. Overall, cost declined by as much as 35 % for the quantity of rhenium chambers, and manufacturing time was decreased by 30-40 %. The quantity of rhenium metal powder used to produce a rhenium chamber was reduced by approximately 70 %, with a subsequent reduction of nearly 50 % in secondary machining operation schedules. Thus, it is apparent that the overall savings provided by the production of near-net shape powder metallurgy rhenium components will be more than merely another aspect of any project involving high temperature applications, it will constitute significant benefit. (author)

Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting

Science.gov (United States)

Murr, L. E.; Martinez, E.; Gaytan, S. M.; Ramirez, D. A.; Machado, B. I.; Shindo, P. W.; Martinez, J. L.; Medina, F.; Wooten, J.; Ciscel, D.; Ackelid, U.; Wicker, R. B.

2011-11-01

Microstructures and a microstructural, columnar architecture as well as mechanical behavior of as-fabricated and processed INCONEL alloy 625 components produced by additive manufacturing using electron beam melting (EBM) of prealloyed precursor powder are examined in this study. As-fabricated and hot-isostatically pressed ("hipped") [at 1393 K (1120 °C)] cylinders examined by optical metallography (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive (X-ray) spectrometry (EDS), and X-ray diffraction (XRD) exhibited an initial EBM-developed γ″ (bct) Ni3Nb precipitate platelet columnar architecture within columnar [200] textured γ (fcc) Ni-Cr grains aligned in the cylinder axis, parallel to the EBM build direction. Upon annealing at 1393 K (1120 °C) (hot-isostatic press (HIP)), these precipitate columns dissolve and the columnar, γ, grains recrystallized forming generally equiaxed grains (with coherent {111} annealing twins), containing NbCr2 laves precipitates. Microindentation hardnesses decreased from 2.7 to 2.2 GPa following hot-isostatic pressing ("hipping"), and the corresponding engineering (0.2 pct) offset yield stress decreased from 0.41 to 0.33 GPa, while the UTS increased from 0.75 to 0.77 GPa. However, the corresponding elongation increased from 44 to 69 pct for the hipped components.

Interaction between climate, volcanism, and isostatic rebound in Southeast Alaska during the last deglaciation

Science.gov (United States)

Praetorius, Summer; Mix, Alan; Jensen, Britta; Froese, Duane; Milne, Glenn A.; Wolhowe, Matthew; Addison, Jason A.; Prahl, Fred

2016-01-01

Observations of enhanced volcanic frequency during the last deglaciation have led to the hypothesis that ice unloading in glaciated volcanic terrains can promote volcanism through decompression melting in the shallow mantle or a reduction in crustal magma storage time. However, a direct link between regional climate change, isostatic adjustment, and the initiation of volcanism remains to be demonstrated due to the difficulty of obtaining high-resolution well-dated records that capture short-term climate and volcanic variability traced to a particular source region. Here we present an exceptionally resolved record of 19 tephra layers paired with foraminiferal oxygen isotopes and alkenone paleotemperatures from marine sediment cores along the Southeast Alaska margin spanning the last deglacial transition. Major element compositions of the tephras indicate a predominant source from the nearby Mt. Edgecumbe Volcanic Field (MEVF). We constrain the timing of this regional eruptive sequence to 14.6–13.1 ka. The sudden increase in volcanic activity from the MEVF coincides with the onset of Bølling–Allerød interstadial warmth, the disappearance of ice-rafted detritus, and rapid vertical land motion associated with modeled regional isostatic rebound in response to glacier retreat. These data support the hypothesis that regional deglaciation can rapidly trigger volcanic activity. Rapid sea surface temperature fluctuations and an increase in local salinity (i.e., δ18Osw) variability are associated with the interval of intense volcanic activity, consistent with a two-way interaction between climate and volcanism in which rapid volcanic response to ice unloading may in turn enhance short-term melting of the glaciers, plausibly via albedo effects on glacier ablation zones.

Analysis of Institutional Press Releases and its Visibility in the Press

Directory of Open Access Journals (Sweden)

José Antonio Alcoceba-Hernando, Ph.D.

2010-01-01

Full Text Available The relationships between institutional communication and media communication influence the shaping of social representations of public issues. This research article analyses these relationships based on the case study of the external communication of a public institution, the press releases of Spain’s Youth Institute (Instituto de la Juventud, aka, Injuve, during three years and their repercussion in the press during the same period of time. The results obtained in this research allowed drawing conclusions on the types of communication production of the aforementioned institution and the news treatment of such pieces of information by the printed and digital media. The press releases and the news items were studied using quantitative media content analysis which focused, especially, in referential issues like the information treatment, the thematic analysis, youth representations in the case of the releases; and the visibility of the press releases in the making of news

Isostatic lines’ study to optimize steel space grid envelope structures for tall buildings according to their solicitations

OpenAIRE

Señís López, Roger

2013-01-01

Based on the first study completed with wind tunnel tests, the aim of this paper is to define a second methodology for the optimization of steel space grid envelope structures for tall buildings according to their isostatic lines according to their solicitations. It is by means of the comparison NatHaz online database and numerical simulation research of wind flow repercussion in buildings, through Computational Fluid Dynamics (CDF), that we can understand and analyse the grid ...

Glacial isostatic adjustment and sea-level change. State of the art report

International Nuclear Information System (INIS)

Whitehouse, Pippa

2009-04-01

This report outlines the physics of glacial isostatic adjustment (GIA), how this affects sea-level, and the methods which are employed by researchers to study and understand these processes. The report describes the scientific background into the processes and methods presented in SKB TR-06-23 (INIS ref 38-021351). The purpose of this report is to provide a reference document for people who require a more in-depth understanding of GIA processes than is presented in the earlier report. The key components of the GIA system are described, and this is followed by a concise description of the processes that take place within and between these components during a glacial cycle. The report contains 4 chapters: Chapter 1, 'Introduction'; Chapter 2, 'GIA systems', describes the three main systems which are involved in the GIA process; the solid Earth, the hydrosphere and the cryosphere. The various parameters which govern the behaviour of these systems, and must be known in order to model GIA processes, are defined. Chapter 3, 'Governing equations', lays out the physics of GIA and derives the equations which must be solved to determine the redistribution of water over the surface of the Earth, and the solid Earth response. Secondary processes, such as ocean syphoning, are also described. The driving forces behind glacial cycles are briefly discussed. The methods used to solve these equations are laid out in chapter 4, 'State-of-the-art GIA models'. In this chapter, the different approaches used by different groups of researchers are discussed, as are the relative accuracy of the methods. Recent improvements to the theory are described, as are current shortcomings of the models. The various data sets used to calibrate and verify the accuracy of the modelling are also briefly described in this chapter. In the past few years advances in computational speed have enabled researchers to develop models which attempt to account for the effects 3-D Earth structure upon GIA processes

Reading and Not-Printing: Obstruction at the Crater Press

Directory of Open Access Journals (Sweden)

Richard Parker

2014-11-01

Full Text Available I will begin this paper with a brief and partial history of American printing, detecting a shared predilection for a noticeably maverick relation to the printed page in the works (printed and otherwise of Samuel Keimer and Benjamin Franklin during the colonial period, and the works of Walt Whitman, Emily Dickinson and Mark Twain in the nineteenth-century. I term the interrupted, dialectical printing that connects all of these writer/printers ‘not-printing’, and offer some explanation of his term and a description of some of its manifestations. I will then move on to consider how the idea of ‘not-printing’ might be helpful for the consideration of some contemporary British and American poets and printers before concluding with a description of some of the ways that the productive constraints of such a practice have influenced my own work as editor and printer at the Crater Press.

WordPress Top Plugins

CERN Document Server

Corbin, Brandon

2010-01-01

Time flies when you're having fun. This is the right way to describe this WordPress Top Plugins book by Brandon Corbin. With real world examples and by showing you the perks of having these plugins installed on your websites, the author is all set to captivate your interest from start to end. Regardless of whether this is your first time working with WordPress, or you're a seasoned WordPress coding ninja, WordPress Top Plugins will walk you through finding and installing the best plugins for generating and sharing content, building communities and reader base, and generating real advertising r

Which Freedom of the Press?

DEFF Research Database (Denmark)

Rytter, Jens Elo

2010-01-01

The article surveys the historical and current meaning of "Freedom of the Press" in constitutional and human rights law. Two different conceptions exist, the narrow one defining freedom of the press as the freedom of every one to publish without prior restraint, the broader one defining it as a...... privileged freedom of the organised press to gather and report on information of public interest. These two conceptions have very different answers to the question of whether the press should enjoy some privilege to be exempt from ordinary legislation when such legislation restricts the access of the press to inform...

Hot-pressing steatite bodies

International Nuclear Information System (INIS)

Aparicio Arroyo, E.

1967-01-01

Requirements for some special nuclear engineering ceramic shapes are: big size, impervious, dimensional accuracy and good mechanical and dielectric properties. Limitations of te conventional methods and advantages of te hot pressing techniques for the manufacturing of these shapes are discussed. Hot pressing characteristics of a certain steatite powder are studied. Occurrence of an optimum densification temperature just above the tale decomposition range is found. Experimental data show that the height/diameter ratio of the specimen has no effect on the sintering conditions. Increasing darkness from the graphite mould is detected above the optimum temperature. The hot-pressed steatite is compared with a fired dry-pressed sample of the same composition. (Author) 13 refs

Mathematical modelling of wet paper pressing

NARCIS (Netherlands)

Bežanovic, D.

2005-01-01

The aim of this project is to reduce energy costs in paper production by optimising the process in the press section of a paper machine. In this press section water is squeezed as it passes through the press nip. In a modern press section the moisture content of the sheet after three or four presses

Densification of porous bodies in a granular pressure-transmitting medium

International Nuclear Information System (INIS)

Olevsky, E.A.; Ma, J.; LaSalvia, J.C.; Meyers, M.A.

2007-01-01

Densification is a critical step in the manufacture of near-net-shaped components via powder processing. A non-isostatic stress state will in general result in shape distortion in addition to densification. In the quasi-isostatic pressing (QIP) process the green body is placed into a granular pressure-transmitting medium (i.e. PTM), which is itself contained in a rigid die. Upon the application of a uniaxial load, the PTM redistributes the tractions on the green body, thereby creating a stress state that is quasi-isostatic. The character of the deformation of the PTM is studied using model experiments on pressing of the PTM in a rigid die and a scanning electron microscopy analysis of the PTM powder. An important problem of the optimization of the PTM chemical composition enabling the maximum densification of a porous specimen with the minimum possible shape distortion is solved. The results of modeling agree satisfactorily with the experimental data on cold QIPing Ti and Ni powder samples and hot QIPing TiC-TiNi cermet composites

What causes addiction problems? Environmental, biological and constitutional explanations in press portrayals from four European welfare societies.

Science.gov (United States)

Hellman, Matilda; Majamäki, Maija; Rolando, Sara; Bujalski, Michał; Lemmens, Paul

2015-03-01

Press items (N = 1327) about addiction related problems were collected from politically independent daily newspapers in Finland, Italy, the Netherlands, and Poland from 1991, 1998, and 2011. A synchronized qualitative coding was performed for discerning the descriptions of the genesis to the problems in terms of described causes to and reasons for why they occur. Environmental explanations were by far the most common and they varied most between the materials. The analysis documents how the portrayals include traces of their contextual origin, relating to different media tasks and welfare cultural traditions. Meaning-based differences were also assigned to the kind of problems that held the most salience in the press reporting. A general worry over societal change is tied into the explanations of accumulating addiction problems and underpins the press reporting in all countries.

European Fusion Programme. ITER task T23: Beryllium characterisation. Progress report. Tensile tests on neutron irradiated and reference beryllium

International Nuclear Information System (INIS)

Moons, F.

1996-02-01

As part of the European Technology Fusion Programme, the irradiation embrittlement characteristics of the more ductile and isotopic grades of beryllium manufactured by Brush Wellman has been investigated using modern powder production and consolidation techniques . This study was initiated in support of the development and evaluation of beryllium as a neutron multiplier for the solid breeder blanket design concepts proposed for a DEMO fusion power reactor. Four different species of beryllium: S-200 F (vacuum hot pressed, 1.2 wt% BeO), S-200FH (hot isostatic pressed, 0.9 wt% BeO), S-65 (vacuum hot pressed, 0.6 wt% BeO), S-65H (hot isostatic pressed, 0.5 wt% BeO) have been compared. Three batches of the beryllium have been investigated, a neutron batch, a thermal control batch and a reference batch. Neutron irradiation has been performed at temperatures between 175 and 605 degrees Celsius up to a neutron fluence of 2.1 10 25 n.m -2 (E> 1 MeV) or 750 appm He. The results of the tensile tests are summarized

Joining of porous silicon carbide bodies

Science.gov (United States)

Bates, Carl H.; Couhig, John T.; Pelletier, Paul J.

1990-05-01

A method of joining two porous bodies of silicon carbide is disclosed. It entails utilizing an aqueous slip of a similar silicon carbide as was used to form the porous bodies, including the sintering aids, and a binder to initially join the porous bodies together. Then the composite structure is subjected to cold isostatic pressing to form a joint having good handling strength. Then the composite structure is subjected to pressureless sintering to form the final strong bond. Optionally, after the sintering the structure is subjected to hot isostatic pressing to further improve the joint and densify the structure. The result is a composite structure in which the joint is almost indistinguishable from the silicon carbide pieces which it joins.

Extensional fault geometry and its flexural isostatic response during the formation of the Iberia - Newfoundland conjugate rifted margins

Science.gov (United States)

Gómez-Romeu, Júlia; Kusznir, Nick; Manatschal, Gianreto; Roberts, Alan

2017-04-01

Despite magma-poor rifted margins having been extensively studied for the last 20 years, the evolution of extensional fault geometry and the flexural isostatic response to faulting remain still debated topics. We investigate how the flexural isostatic response to faulting controls the structural development of the distal part of rifted margins in the hyper-extended domain and the resulting sedimentary record. In particular we address an important question concerning the geometry and evolution of extensional faults within distal hyper-extended continental crust; are the seismically observed extensional fault blocks in this region allochthons from the upper plate or are they autochthons of the lower plate? In order to achieve our aim we focus on the west Iberian rifted continental margin along the TGS and LG12 seismic profiles. Our strategy is to use a kinematic forward model (RIFTER) to model the tectonic and stratigraphic development of the west Iberia margin along TGS-LG12 and quantitatively test and calibrate the model against breakup paleo-bathymetry, crustal basement thickness and well data. RIFTER incorporates the flexural isostatic response to extensional faulting, crustal thinning, lithosphere thermal loads, sedimentation and erosion. The model predicts the structural and stratigraphic consequences of recursive sequential faulting and sedimentation. The target data used to constrain model predictions consists of two components: (i) gravity anomaly inversion is used to determine Moho depth, crustal basement thickness and continental lithosphere thinning and (ii) reverse post-rift subsidence modelling consisting of flexural backstripping, decompaction and reverse post-rift thermal subsidence modelling is used to give paleo-bathymetry at breakup time. We show that successful modelling of the structural and stratigraphic development of the TGS-LG12 Iberian margin transect also requires the simultaneous modelling of the Newfoundland conjugate margin, which we

Four Theories of the Press.

Science.gov (United States)

Siebert, Fred S.; And Others

A systematic understanding of the press requires an understanding of the social and political structures within which the press operates. This book discusses four theories that have determined the kind of press the Western world has had: authoritarian, libertarian, socially responsible, and Soviet communist. Each chapter discusses press…

MIS 5e relative sea-level changes in the Mediterranean Sea: Contribution of isostatic disequilibrium

Science.gov (United States)

Stocchi, Paolo; Vacchi, Matteo; Lorscheid, Thomas; de Boer, Bas; Simms, Alexander R.; van de Wal, Roderik S. W.; Vermeersen, Bert L. A.; Pappalardo, Marta; Rovere, Alessio

2018-04-01

Sea-level indicators dated to the Last Interglacial, or Marine Isotope Stage (MIS) 5e, have a twofold value. First, they can be used to constrain the melting of Greenland and Antarctic Ice Sheets in response to global warming scenarios. Second, they can be used to calculate the vertical crustal rates at active margins. For both applications, the contribution of glacio- and hydro-isostatic adjustment (GIA) to vertical displacement of sea-level indicators must be calculated. In this paper, we re-assess MIS 5e sea-level indicators at 11 Mediterranean sites that have been generally considered tectonically stable or affected by mild tectonics. These are found within a range of elevations of 2-10 m above modern mean sea level. Four sites are characterized by two separate sea-level stands, which suggest a two-step sea-level highstand during MIS 5e. Comparing field data with numerical modeling we show that (i) GIA is an important contributor to the spatial and temporal variability of the sea-level highstand during MIS 5e, (ii) the isostatic imbalance from the melting of the MIS 6 ice sheet can produce a >2.0 m sea-level highstand, and (iii) a two-step melting phase for the Greenland and Antarctic Ice Sheets reduces the differences between observations and predictions. Our results show that assumptions of tectonic stability on the basis of the MIS 5e records carry intrinsically large uncertainties, stemming either from uncertainties in field data and GIA models. The latter are propagated to either Holocene or Pleistocene sea-level reconstructions if tectonic rates are considered linear through time.

WordPress 3.7 complete

CERN Document Server

Król, Karol

2013-01-01

WordPress 3.5 Complete: Third Edition is a comprehensive and step-by-step tutorial packed with screenshots and examples to make it easy and quick to pick it up.This WordPress book is a guide to WordPress for online publishers and web developers. If you are new to blogging and want to create your own blog or website from scratch, then ""WordPress 3.5 Complete: Third Edition"" is for you. No prior knowledge of HTML/CSS or PHP is required.

Thermal cycling tests of actively cooled beryllium copper joints

Energy Technology Data Exchange (ETDEWEB)

Roedig, M.; Duwe, R.; Linke, J.; Schuster, A.; Wiechers, B. [Forschungszentrum Juelich GmbH (Germany)

1998-01-01

Screening tests (steady state heating) and thermal fatigue tests with several kinds of beryllium-copper joints have been performed in an electron beam facility. Joining techniques under investigation were brazing with silver containing and silver-free braze materials, hot isostatic pressing (HIP) and diffusion bonding (hot pressing). Best thermal fatigue performance was found for the brazed samples. (author)

IMPROVEMENT OF WEAR COMPONENT'S PERFORMANCE BY UTILIZING ADVANCED MATERIALS AND NEW MANUFACTURING TECHNOLOGIES: CASTCON PROCESS FOR MINING APPLICATIONS

International Nuclear Information System (INIS)

Xiaodi Huang; Richard Gertsch

2001-01-01

The fibrous monolith material was successfully consolidated in both the hot press and the hot isostatic press. Initial evaluations indicate the material will have a very high fracture toughness and be very hard. Tungsten carbide was successfully consolidated in an H13 tool steel with the incorporation of a Co-Cr layer between the WC and the steel

Conditioning processes for incinerator ashes

International Nuclear Information System (INIS)

Jouan, A.; Ouvrier, N.; Teulon, F.

1990-01-01

Three conditioning processes for alpha-bearing solid waste incineration ashes were investigated and compared according to technical and economic criteria: isostatic pressing, cold-crucible direct-induction melting and cement-resin matrix embedding

Smashing WordPress Beyond the Blog

CERN Document Server

Hedengren, Thord Daniel

2011-01-01

Smashing WordPress shows you how to utilize the power of the WordPress platform, and provides a creative spark to help you build WordPress-powered sites that go beyond the obvious. The second edition of Smashing WordPress has been updated for WordPress 3.1+, which includes internal, custom post types, the admin bar, and lots of other useful new features. You will learn the core concepts used to post types, the admin bar, and lots of other useful new features. You will learn the core concepts used to build just about anything in WordPress, resulting in fast deployments and greater design flexib

Smashing WordPress Beyond the Blog

CERN Document Server

Hedengren, Thord Daniel

2012-01-01

The ultimate guide to WordPress, from the world's most popular resource for web designers and developers As one of the hottest tools on the web today for creating a blog, WordPress has evolved to be much more that just a blogging platform and has been pushed beyond its original purpose. With this new edition of a perennially popular WordPress resource, Smashing Magazine offers you the information you need so you can maximize the potential and power of WordPress. WordPress expert Thord Daniel Hedengren takes you beyond the basic blog to show you how to leverage the capabilities of WordPress to

Kinetics and mechanisms of creep in hot isostatically pressed niobium carbide

International Nuclear Information System (INIS)

Nixon, R.D.; Davis, R.F.; Bentley, J.

1986-01-01

Constant compressive stress creep experiments in the temperature and stress ranges of 1730K - 2100K and 16 MN/m 2 - 70 MM/m 2 on HIPed NbC 0.74 have revealed stress exponents of 2.0 under stress levels of 16-54 MN/m 2 at all temperatures investigated and 3.2 under stress levels of 54-70 MN/m 2 at 1830K. The activation energy of steady state creep is approximately 230 kJ/mol in the temperature range of 1730K - 1930K under 48-54 MN/m 2 and 470 kJ/mol in the temperature range of 1900K - 2100K under 64 MN/m 2 . TEM of the annealed but uncrept material reveals grown-in dislocation subboundaries. At 1730K and under 34-54 MN/m 2 , these subboundaries become single dislocations and dipoles. At 1830K and under 54-70 MN/m 2 the subboundaries evolve into simple tilt boundaries which are occasionally knitted, indicating more glide activity at higher stresses. At 1930K and under 34-54 MN/m 2 , hexagonal subboundaries form, but are not as well defined as in the annealed material. At 2100K and under 16-30 MN/m 2 , the subboundaries are well-defined hexagonal networks which become polygonized under higher stresses on 64 MN/m 2 . The experimental and TEM results indicate that at low temperatures (below 0.5 T m = 2073K) and at all stresses, creep occurs by dislocation glide which is accompanied by subgrain and high angle boundary interaction. At high temperature (above 0.5 T m ), strain occurs by glide and subboundary movement; recovery occurs by climb in the subboundary

Muscle activation when performing the chest press and shoulder press on a stable bench vs. a Swiss ball.

Science.gov (United States)

Uribe, Brandon P; Coburn, Jared W; Brown, Lee E; Judelson, Daniel A; Khamoui, Andy V; Nguyen, Diamond

2010-04-01

The aim of this study was to examine the effects of a stable surface (bench) vs. an unstable surface (Swiss ball) on muscle activation when performing the dumbbell chest press and shoulder press. Sixteen healthy men (24.19 +/- 2.17 years) performed 1 repetition maximum (1RM) tests for the chest press and shoulder press on a stable surface. A minimum of 48 hours post 1RM, subjects returned to perform 3 consecutive repetitions each of the chest press and shoulder press at 80% 1RM under 4 different randomized conditions (chest press on bench, chest press on Swiss ball, shoulder press on bench, shoulder press on Swiss ball). Electromyography was used to assess muscle activation of the anterior deltoid, pectoralis major, and rectus abdominus. The results revealed no significant difference in muscle activation between surface types for either exercise. This suggests that using an unstable surface neither improves nor impairs muscle activation under the current conditions. Coaches and other practitioners can expect similar muscle activation when using a Swiss ball vs. a bench.

Porous mandrels provide uniform deformation in hydrostatic powder metallurgy

Science.gov (United States)

Gripshover, P. J.; Hanes, H. D.

1967-01-01

Porous copper mandrels prevent uneven deformation of beryllium machining blanks. The beryllium powder is arranged around these mandrels and hot isostatically pressed to form the blanks. The mandrels are then removed by leaching.

Investing in a Large Stretch Press

Science.gov (United States)

Choate, M.; Nealson, W.; Jay, G.; Buss, W.

1986-01-01

Press for forming large aluminum parts from plates provides substantial economies. Study assessed advantages and disadvantages of investing in large stretch-forming press, and also developed procurement specification for press.

AUPress: A Comparison of an Open Access University Press with Traditional Presses

Science.gov (United States)

McGreal, Rory; Chen, Nian-Shing

2011-01-01

This study is a comparison of AUPress with three other traditional (non-open access) Canadian university presses. The analysis is based on the rankings that are correlated with book sales on Amazon.com and Amazon.ca. Statistical methods include the sampling of the sales ranking of randomly selected books from each press. The results of one-way…

Professional WordPress design and development

CERN Document Server

Williams, Brad; Stern, Hal

2014-01-01

The highest rated WordPress development and design book on the market is back with an all new third edition. Professional WordPress is the only WordPress book targeted to developers, with advanced content that exploits the full functionality of the most popular CMS in the world. Fully updated to align with WordPress 4.1, this edition has updated examples with all new screenshots, and full exploration of additional tasks made possible by the latest tools and features. You will gain insight into real projects that currently use WordPress as an application framework, as well as the basic usage a

BuddyPress theme development

CERN Document Server

Lister, Tammie

2013-01-01

This book is a hands-on tutorial guide to using BuddyPress.This book is great for designers and developers who are looking to learn how to develop BuddyPress themes. It's assumed that the reader has some understanding of Wordpress and is familiar with CSS and HTML.

Effect of thermally induced porosity on an as-HIP powder metallurgy superalloy

Science.gov (United States)

Dreshfield, R. L.; Miner, R. V., Jr.

1979-01-01

The impact of thermally induced porosity on the mechanical properties of an as-hot-isostatically-pressed and heat treated pressing made from low carbon Astroloy was determined. Porosity in the disk-shape pressing studied ranged from 2.6 percent at the bore to 1.4 percent at the rim. Tensile, yield strength, ductility, and rupture life of the rim of the porous pressing was only slightly inferior to the rim of sound pressings. The strength, ductility, and rupture life of the bore of the porous pressing was severely degraded compared to sound pressings. At strain ranges typical of commercial jet engine designs, the rim of the porous pressing had slightly inferior fatigue life to sound pressings.

Glacial isostatic adjustment and sea-level change. State of the art report

Energy Technology Data Exchange (ETDEWEB)

Whitehouse, Pippa (Durham Univ., Dept. of Geography, Durham (United Kingdom))

2009-04-15

This report outlines the physics of glacial isostatic adjustment (GIA), how this affects sea-level, and the methods which are employed by researchers to study and understand these processes. The report describes the scientific background into the processes and methods presented in SKB TR-06-23 (INIS ref 38-021351). The purpose of this report is to provide a reference document for people who require a more in-depth understanding of GIA processes than is presented in the earlier report. The key components of the GIA system are described, and this is followed by a concise description of the processes that take place within and between these components during a glacial cycle. The report contains 4 chapters: Chapter 1, 'Introduction'; Chapter 2, 'GIA systems', describes the three main systems which are involved in the GIA process; the solid Earth, the hydrosphere and the cryosphere. The various parameters which govern the behaviour of these systems, and must be known in order to model GIA processes, are defined. Chapter 3, 'Governing equations', lays out the physics of GIA and derives the equations which must be solved to determine the redistribution of water over the surface of the Earth, and the solid Earth response. Secondary processes, such as ocean syphoning, are also described. The driving forces behind glacial cycles are briefly discussed. The methods used to solve these equations are laid out in chapter 4, 'State-of-the-art GIA models'. In this chapter, the different approaches used by different groups of researchers are discussed, as are the relative accuracy of the methods. Recent improvements to the theory are described, as are current shortcomings of the models. The various data sets used to calibrate and verify the accuracy of the modelling are also briefly described in this chapter. In the past few years advances in computational speed have enabled researchers to develop models which attempt to account for the

Encapsulation and handling of spent nuclear fuel for final disposal

International Nuclear Information System (INIS)

Loennerberg, B.; Larker, H.; Ageskog, L.

1983-05-01

The handling and embedding of those metal parts which arrive to the encapsulation station with the fuel is described. For the encapsulation of fuel two alternatives are presented, both with copper canisters but with filling of lead and copper powder respectively. The sealing method in the first case is electron beam welding, in the second case hot isostatic pressing. This has given the headline of the two chapters describing the methods: Welded copper canister and Pressed copper canister. Chapter 1, Welded copper canister, presents the handling of the fuel when it arrives to the encapsulation station, where it is first placed in a buffer pool. From this pool the fuel is transferred to the encapsulation process and thereby separated from fuel boxes and boron glass rod bundles, which are transported together with the fuel. The encapsulation process comprises charging into a copper canister, filling with molten lead, electron beam welding of the lid and final inspection. The transport to and handling in the final repository are described up to the deposition and sealing in the deposition hole. Handling of fuel residues is treated in one of the sections. In chapter 2, Pressed copper canister, only those parts of the handling, which differ from chapter 1 are described. The hot isostatic pressing process is given in the first sections. The handling includes drying, charging into the canister, filling with copper powder, seal lid application and hot isostatic pressing before the final inspection and deposition. In the third chapter, BWR boxes in concrete moulds, the handling of the metal parts, separated from the fuel, are dealt with. After being lifted from the buffer pool they are inserted in a concrete mould, the mould is filled with concrete, covered with a lid and after hardening transferred to its own repository. The deposition in this repository is described. (author)

Conférence de presse | Press Conference

CERN Multimedia

CERN. Geneva; Bejar Alonso, Isabel

2018-01-01

10:00-11:00 Conférence de presse en présence de Lucio Rossi, chef du projet LHC à Haute Luminosité et Isabel Bejar Alonso, chargée de la configuration, de la qualité et des ressources du projet LHC à Haute Luminosité.

Evidence for Isostatic Emergence and Holocene Environmental Change Recorded in Chironomid Assemblages and Sediment Composition of Coastal Lake T1 in SW Greenland

Science.gov (United States)

Berman, K.; Axford, Y.; Lasher, G. E.

2017-12-01

Multi-proxy analysis of a coastal lake in southwest Greenland near Nuuk provides evidence for regional environmental changes, including the timing of isostatic rebound and the temperature history of the area. T1 (informal name) is a small lake 50 km south of Nuuk, at 17.5 m elevation and currently isolated from glacial meltwater drainage. The lake's sediment record begins approximately 9500 cal years BP, when the site was submerged beneath sea level due to glacial isostatic depression following the Last Glacial Maximum. The record captures the transition of the environment from a submerged, glacially-influenced marine site to a non-glacially fed (and initially meromictic) freshwater lake 8600 cal years BP. Magnetic susceptibility, a proxy for sediment minerogenic content, decreased rapidly from 9500 to 8600 years BP, before abruptly stabilizing and remaining relatively low and steady for the rest of the record. The transition to a lacustrine environment was characterized by a rapid and relatively simultaneous increase in primary productivity (inferred from biogenic silica concentrations) and shift towards terrestrial versus marine sources of organic matter (inferred from carbon:nitrogen ratios and nitrogen isotopes) between 8700 and 8400 years BP. Together, these proxies and the presence of marine shells below the transition provide robust evidence for the transition from a marine environment to a freshwater lake in response to regional postglacial isostatic rebound. Within the Holocene, measures of bulk sediment composition (e.g., biogenic silica, loss-on-ignition and magnetic susceptibility) are relatively stable. Chironomid (Insecta: Diptera: Chironomidae) assemblages, which in some environments are quantitative proxies for summer temperature changes, show species-level shifts within the Holocene that will be interpreted in this presentation alongside indicators of landscape change including carbon:nitrogen ratios, bulk sediment spectral reflectance and bulk

Study of the mechanical properties of stainless steel 316LN prepared by hot isostatic compression. Influence of preparation parameters

International Nuclear Information System (INIS)

Couturier, Raphael

1999-01-01

This research thesis has been performed within an R and D programme which aimed at optimising and certifying the HIP process (hot isostatic pressing) from a technological as well as metallurgical point of view. The objective has been to improve dimensional reproducibility of fabricated parts, and metallurgical properties of the dense material. Reference parts are those belonging to PWR primary circuit, and are made in cast austenitic-ferritic steel. Thus, the objective has been to show that these parts can be beneficially fabricated by powder metallurgy in austenitic grade. A mock part (a primary circuit pump wheel at the 1/2 scale) has first been fabricated by HIP, and a more complex shape generator has been designed. The author reports the determination of microstructure and mechanical characteristics of the austenitic 316LN steel produced by HIP and used to fabricate mock parts and demonstrator parts, the study of the relationship between dense material properties and fabrication parameters (temperature, pressure, consolidation time), and the analysis of the consequences of an elaboration by HIP on the 316LN steel with comparison with forged parts. After a presentation of the Powder Metallurgy elaboration technique, the author reports a bibliographical study on the precipitation at Prior Particle Boundaries (PPB), reports the study of microstructure and mechanical properties of the HIPed 316LN, and discusses the possibility of a decrease of precipitation at PPBs by adjusting powder degassing or a granulometric sorting. The last part reports the extension of the study of steel coherence to a temperature range which encompasses the primary circuit operation temperature (350 C). Resilience tests are performed as well as mechanical tests on notched axisymmetric samples. A finite element calculation of these samples allows the validation of the use of a Thomson-type model to describe the emergence of defects which are typical of a steel elaborated by powder

Tantalum powder consolidation, modeling and properties

International Nuclear Information System (INIS)

Bingert, S.R.; Vargas, V.D.; Sheinberg, H.C.

1996-01-01

A systematic approach was taken to investigate the consolidation of tantalum powders. The effects of sinter time, temperature and ramp rate; hot isostatic pressing (HIP) temperature and time; and powder oxygen content on consolidation density, kinetics, microstructure, crystallographic texture, and mechanical properties have been evaluated. In general, higher temperatures and longer hold times resulted in higher density compacts with larger grain sizes for both sintering and HIP'ing. HIP'ed compacts were consistently higher in density than sintered products. The higher oxygen content powders resulted in finer grained, higher density HIP'ed products than the low oxygen powders. Texture analysis showed that the isostatically processed powder products demonstrated a near random texture. This resulted in isotropic properties in the final product. Mechanical testing results showed that the HIP'ed powder products had consistently higher flow stresses than conventionally produced plates, and the sintered compacts were comparable to the plate material. A micromechanics model (Ashby HIP model) has been employed to predict the mechanisms active in the consolidation processes of cold isostatic pressing (CIP), HIP and sintering. This model also predicts the density of the end product and whether grain growth should be expected under the applied processing conditions

The Impact of a Mechanical Press on the Accuracy of Products and the Reliability of Tools in Cold Forging

DEFF Research Database (Denmark)

Krusic, V.; Arentoft, Mogens; Rodic, T.

2005-01-01

Cold extrusion is an economic production process for the production of elements of complex forms and accurate dimensions. The first part of the article is about the impact that mechanical press has on the accuracy of products and reliability of tools. There is a description of the mechanical pres...

COMPARISON OF THE MECHANICAL RESPONSE OF POROUS TI-6AL-4V ALLOYS PRODUCED BY DIFFERENT COMPACTION TECHNIQUES

Directory of Open Access Journals (Sweden)

G.İpek Selimoğlu

2017-03-01

Full Text Available Porous Ti-6Al-4V alloys are attractive candidates as implant materials due to their good biocompatibility combined with the porous structure leading to increased osseointegration and decreased stiffness. Accordingly, different processing techniques were employed for the production of Ti-6Al-4V foams in the literature. Among these techniques, sintering with space holder is used to produce porous Ti-6Al-4V alloys in this study. Magnesium was employed as the space holder material because of its relatively low boiling point as well as high oxygen affinity. Two different compaction techniques, die compaction with hydraulic pressing and cold isostatic pressing (CIP, were employed for obtaining green compacts. Both spherical and nonspherical Ti-6Al-4V powders were used to investigate the effect of powder shape on compaction. Processed foams were characterized in terms of both microstructural and mechanical aspects in order to investigate the effect of pressing conditions in combination with powder characteristics. It was observed that NS-CIP foam, which was produced by compacting nonspherical powders by cold isostatic press, has the highest strength. However, the S-DP foam, which was produced by die-pressing of spherical powders, has the highest toughness.

WordPress all-in-one for dummies

CERN Document Server

Sabin-Wilson, Lisa

2013-01-01

Top WordPress guide, now fully updated for the latest WordPress release! This updated new edition comprises one of the largest collections of practical intermediate to advanced information on WordPress. Fully updated for the latest WordPress release, this in-depth book covers it all, from setting up your software to publishing your site, using SEO and social media, developing and using plug-ins, running multiple sites with WordPress, and more. Veteran author Lisa Sabin-Wilson is a top authority on WordPress, and she and her co-authors pack this book with essential and easy-to-follo

Press to compress contaminated wastes drums

International Nuclear Information System (INIS)

Prevost, J.

1993-01-01

This patent describes a press for contaminated wastes drums pressing. The press is made of a structure comprising a base and an upper stringer bind to the base by vertical bearers, a compression system comprising a main cylinder and a ram, connected to the upper stringer

ISS Expedition 08 Press Kit

Data.gov (United States)

National Aeronautics and Space Administration — Press kit for ISS mission Expedition 08 from 10/2003-04/2004. Press kits contain information about each mission overview, crew, mission timeline, benefits, and media...

Bullying the media : Cultural and climato-economic readings of press repression versus press freedom

NARCIS (Netherlands)

Van de Vliert, E.

Journalists and media assistants in many places are murdered, imprisoned, censored, threatened, and similarly harrassed. Here I document that, and explain why, there are three climato-economic niches of press repression versus press freedom as part of broader syndromes of national culture. A

Coupling intensity and isostatic competition between subducting slab and overriding plate control trench motions and tectonics of the overriding plate

Science.gov (United States)

Wu, G.; Moresi, L. N.

2017-12-01

Trench motions not only reflect tectonic regimes on the overriding plate but also shed light on the competition between subducting slab and overriding plate, however, major controls over trench advance or retreat and their consequences are still illusive. We use 2D thermo-mechanical experiments to study the problem. We find that the coupling intensity particularly in the uppermost 200 km and the isostatic competition between subducting slab and overriding plate largely determine trench motion and tectonics of in the overriding plate. Coupling intensity is the result of many contributing factors, including frictional coefficient of brittle part of the subducting interface and the viscosity of the ductile part, thermal regime and rheology of the overriding plate, and water contents and magmatic activity in the subducting slab and overriding plate. In this study, we are not concerned with the dynamic evolution of individual controlling parameter but simply use effective media. For instance, we impose simple model parameters such as frictional coefficient and vary the temperature and strain-rate dependent viscosity of the weak layer between the subducting slab and overriding plate. In the coupled end-member case, strong coupling leads to strong corner flow, depth-dependent compression/extension, and mantle return flow on the overriding plate side. It results in fast trench retreat, broad overriding plate extension, and even slab breakoff. In the decoupled end-member case, weak coupling causes much weaker response on the overriding plate side compared with the coupled end-member case, and the subducting slab can be largely viewed as a conveyer belt. We find that the isostatic competition between the subducting slab and overriding plate also has a major control over trench motion, and may better be viewed in 3D models. This is consistent with the findings in previous 3D studies that trench motion is most pronounced close to the slab edge. Here we propose that the

Activation of Selected Core Muscles during Pressing

Directory of Open Access Journals (Sweden)

Thomas W. Nesser

2015-10-01

Full Text Available Introduction: Unstable surface training is often used to activate core musculature during resistance training. Unfortunately, unstable surface training is risky and leads to detraining. Purpose: The purpose of this study was to determine core muscle activation during stable surface ground-based lifts. Methods: Fourteen recreational trained and former NCAA DI athletes (weight 84.2 ± 13.3 kg; height 176.0 ± 9.5 cm; age 20.9 ± 2.0 years volunteered for participation. Subjects completed two ground-based lifts: overhead press and push-press. Surface EMG was recorded from 4 muscles on the right side of the body (Rectus Abdominus (RA, External Oblique (EO, Transverse Abdominus (TA, and Erector Spinae (ES. Results: Paired sample T-tests identified significant muscle activation differences between the overhead press and the push-press included ES and EO. Average and peak EMG for ES was significantly greater in push-press (P<0.01. Anterior displacement of COP was significantly greater in push-press compared to overhead press during the eccentric phase. Conclusion: The push-press was identified as superior in core muscle activation when compared to the overhead pressing exercise. Keywords: torso, stability, weight lifting, resistance training

Processing of non-oxide ceramics from sol-gel methods

Science.gov (United States)

Landingham, Richard; Reibold, Robert A.; Satcher, Joe

2014-12-12

A general procedure applied to a variety of sol-gel precursors and solvent systems for preparing and controlling homogeneous dispersions of very small particles within each other. Fine homogenous dispersions processed at elevated temperatures and controlled atmospheres make a ceramic powder to be consolidated into a component by standard commercial means: sinter, hot press, hot isostatic pressing (HIP), hot/cold extrusion, spark plasma sinter (SPS), etc.

Immobilization of Uranium Silicides in Sintered Glass

International Nuclear Information System (INIS)

Mateos, P.; Russo, D.O.; Heredia, A.D.; Sanfilippo, M.

2003-01-01

High activity nuclear spent fuels vitrification by fusion is a well known technology which has industrial scale in France, England, Japan, EEUU. Borosilicates glasses are used in this process.Sintered glasses are an alternative to the immobilization task in which there is also a wide experience around the world.The available technics are: cold pressing and sintering , hot-pressing and hot isostatic pressing.This work compares Borosilicates and Iron silicates sintered glasses behaviour when different ammounts of nuclear simulated waste is added

Relative sea-level changes and glacio-isostatic adjustment on the Magdalen Islands archipelago (Atlantic Canada) from MIS 5 to the late Holocene

Science.gov (United States)

Rémillard, Audrey M.; St-Onge, Guillaume; Bernatchez, Pascal; Hétu, Bernard; Buylaert, Jan-Pieter; Murray, Andrew S.; Lajeunesse, Patrick

2017-09-01

The Magdalen Islands (Québec, Canada) in the centre of the Gulf of St. Lawrence are located in a strategic position for providing an overview of the relative sea-level (RSL) history of the Maritime Provinces of eastern Canada. Although data are available for the coastal terrestrial areas of the Maritimes, data from the Gulf are very scarce and both the RSL and glacio-isostatic adjustment (GIA) models extrapolate for this central region. This study provides new stratigraphic and chronological data from four outcrops and two coring sites on the Magdalen Islands. In addition to the five samples used mainly for age control purposes, nine new luminescence ages are presented. With these new data added to the available literature, a new RSL curve is reconstructed for the LGM to the late Holocene period and a partial curve is proposed for the interval between the late MIS 4 to the MIS 3. Data also indicate a few insights for the MIS 5 period. Results reveal that for the LGM to the late Holocene, the curve corresponds to the J-shaped curve scenario recognized in the literature. The RSL changes during this period are the result of glacio-isostatic rebound, migration and collapse of the peripheral forebulge, and eustatic sea-level changes. For the LGM to the early Holocene, glacio-isostatic depression curves displaying a few local differences are also proposed. For the late Holocene, the data constrain the curve between two types of indicators, i.e. marine and terrestrial, and indicate that the RSL has risen at least 3 m during the last two millennia. Sediments dated to the MIS 5 and the interval between the late MIS 4 and the MIS 3 illustrate that the GIA following the LGM also occurred for the MIS 5 interglacial and the MIS 3 interstadial. Finally, recent GIA models are discussed in light of the results of this paper.

QUANTITATIVE NON-DESTRUCTIVE EVALUATION (QNDE) OF THE ELASTIC MODULI OF POROUS TIAL ALLOYS

International Nuclear Information System (INIS)

Yeheskel, O.

2008-01-01

The elastic moduli of γ-TiA1 were studied in porous samples consolidated by various techniques e.g. cold isostatic pressing (CIP), pressure-less sintering, or hot isostatic pressing (HIP). Porosity linearly affects the dynamic elastic moduli of samples. The results indicate that the sound wave velocities and the elastic moduli affected by the processing route and depend not only on the attained density but also on the consolidation temperature. In this paper we show that there is linear correlation between the shear and the longitudinal sound velocities in porous TiA1. This opens the way to use a single sound velocity as a tool for quantitative non-destructive evaluation (QNDE) of porous TiA1 alloys. Here we demonstrate the applicability of an equation derived from the elastic theory and used previously for porous cubic metals

Status of beryllium development for fusion applications

International Nuclear Information System (INIS)

Billone, M.C.; Donne, M.D.; Macaulay-Newcombe, R.G.

1994-05-01

Beryllium is a leading candidate material for the neutron multiplier of tritium breeding blankets and the plasma facing component of first wall and divertor systems. Depending on the application, the fabrication methods proposed include hot-pressing, hot-isostatic-pressing, cold isostatic pressing/sintering, rotary electrode processing and plasma spraying. Product forms include blocks, tubes, pebbles, tiles and coatings. While, in general, beryllium is not a leading structural material candidate, its mechanical performance, as well its performance with regard to sputtering, heat transport, tritium retention/release, helium-induced swelling and chemical compatibility, is an important consideration in first-wall/blanket design. Differential expansion within the beryllium causes internal stresses which may result in cracking, thereby affecting the heat transport and barrier performance of the material. Overall deformation can result in loading of neighboring structural material. Thus, in assessing the performance of beryllium for fusion applications, it is important to have a good database in all of these performance areas, as well as a set of properties correlations and models for the purpose of interpolation/extrapolation

Comparison of the corrosion behaviors of the glass-bonded sodalite ceramic waste form and reference HLW glasses

International Nuclear Information System (INIS)

Ebert, W. L.; Lewis, M. A.

1999-01-01

A glass-bonded sodalite ceramic waste form is being developed for the long-term immobilization of salt wastes that are generated during spent nuclear fuel conditioning activities. A durable waste form is prepared by hot isostatic pressing (HIP) a mixture of salt-loaded zeolite powders and glass frit. A mechanistic description of the corrosion processes is being developed to support qualification of the CWF for disposal. The initial set of characterization tests included two standard tests that have been used extensively to study the corrosion behavior of high level waste (HLW) glasses: the Material Characterization Center-1 (MCC-1) Test and the Product Consistency Test (PCT). Direct comparison of the results of tests with the reference CWF and HLW glasses indicate that the corrosion behaviors of the CWF and HLW glasses are very similar

Two layer powder pressing

International Nuclear Information System (INIS)

Schreiner, H.

1979-01-01

First, significance and advantages of sintered materials consisting of two layers are pointed out. By means of the two layer powder pressing technique metal powders are formed resulting in compacts with high accuracy of shape and mass. Attributes of basic powders, different filling methods and pressing techniques are discussed. The described technique is supposed to find further applications in the field of two layer compacts in the near future

Storytelling as an Instructional Method: Descriptions and Research Questions

Science.gov (United States)

2009-01-01

computational brain . Cambridge, MA: Bradford/ MIT Press. Cianciolo, A. T., Prevou, M., Cianciolo, D., & Morris, R. (2007). Using digital storytelling to...volume 3, no. 2 (Fall 2009) 6–23 Storytelling as an Instructional Method: Descriptions and Research Questions Dee H. Andrews, Thomas D. Hull, and...Jennifer A. Donahue Abstract This paper discusses the theoretical and empirical foundations of the use of storytelling in instruction. The defi nition

Surface degradation of nanocrystalline zirconia dental implants

NARCIS (Netherlands)

Ocelík, Václav; Schepke, Ulf; Rasoul, Hamid Haji; Cune, Marco S.; De Hosson, Jeff Th M.

2017-01-01

Yttria-stabilized zirconia prepared by hot isostatic pressing represents attractive material for biomedical applications. In this work the degradation of yttria-stabilized zirconia dental implants abutments due to the tetragonal to monoclinic phase transformation after one year of clinical use was

Chip compacting press; Jido kirikuzu asshukuki

Energy Technology Data Exchange (ETDEWEB)

Oura, K. [Yuken Kogyo Co. Ltd., Kanagawa (Japan)

1998-08-15

The chips exhausted from various machine tools are massy, occupy much space and make working environment worse by staying added cutting oil to lower part. The chips are exhausted as a result of machining and have not constant quality. Even if used material is same the chips have various shapes and properties by kinds and machining methods of used machine tools, and are troublesome materials from a standpoint of their treatment. Pressing and solidification of the chips have frequently been tried. A chip compacting press introduced in this paper, a relatively cheap chip compacting press aimed for relatively small scale chip treatment, and has such characteristics and effects as follows. Chips are pressed and solidified by each raw material, so fractional management can be easily conducted. As casting metal chips and curled chips of iron and aluminum can be pressed to about 1/3 to 1/5 and about 1/40, respectively, space saving can be conducted. Chip compacting pressing upgrades its transporting efficiency to make possible to reduce its transporting cost. As chip solidification controls its oxidation and most cutting oil are removed, chips are easy to recycle. 2 figs., 1 tab.

WordPress web application development

CERN Document Server

Ratnayake, Rakhitha Nimesh

2013-01-01

An extensive, practical guide that explains how to adapt WordPress features, both conventional and trending, for web applications.This book is intended for WordPress developers and designers who have the desire to go beyond conventional website development to develop quality web applications within a limited time frame and for maximum profit. Experienced web developers who are looking for a framework for rapid application development will also find this to be a useful resource. Prior knowledge with of WordPress is preferable as the main focus will be on explaining methods for adapting WordPres

Professional WordPress Plugin Development

CERN Document Server

Williams, Brad; Tadlock, Justin

2011-01-01

Taking WordPress to the next level with advanced plugin developmentWordPress is used to create self-hosted blogs and sites, and it's fast becoming the most popular content management system (CMS) on the Web. Now you can extend it for personal, corporate and enterprise use with advanced plugins and this professional development guide. Learn how to create plugins using the WordPress plugin API: utilize hooks, store custom settings, craft translation files, secure your plugins, set custom user roles, integrate widgets, work with JavaScript and AJAX, create custom post types. You'll find a practic

WordPress 24-Hour Trainer

CERN Document Server

Plumley, George

2011-01-01

The eagerly anticipated second edition, completely updated for WordPress 3.1 As an open source content management system, WordPress allows users to easily build feature-rich web sites with no programming experience. This unique book-and-video package is a friendly, self-paced beginners guide to the latest release of WordPress. Lessons are focused on practical, everyday tasks that users will need to create and maintain their sites: entering new content, creating new pages, managing menus, making content search-engine friendly. Plus you'll find lots of tips based on years of experience teaching

A comparative study between spiral-filter press and belt press implemented in a cloudy apple juice production process.

Science.gov (United States)

De Paepe, Domien; Coudijzer, Katleen; Noten, Bart; Valkenborg, Dirk; Servaes, Kelly; De Loose, Marc; Diels, Ludo; Voorspoels, Stefan; Van Droogenbroeck, Bart

2015-04-15

In this study, advantages and disadvantages of the innovative, low-oxygen spiral-filter press system were studied in comparison with the belt press, commonly applied in small and medium size enterprises for the production of cloudy apple juice. On the basis of equivalent throughput, a higher juice yield could be achieved with spiral-filter press. Also a more turbid juice with a higher content of suspended solids could be produced. The avoidance of enzymatic browning during juice extraction led to an attractive yellowish juice with an elevated phenolic content. Moreover, it was found that juice produced with spiral-filter press demonstrates a higher retention of phenolic compounds during the downstream processing steps and storage. The results demonstrates the advantage of the use of a spiral-filter press in comparison with belt press in the production of a high quality cloudy apple juice rich in phenolic compounds, without the use of oxidation inhibiting additives. Copyright © 2014 Elsevier Ltd. All rights reserved.

Preliminary studies on fabrication routes for SYNROC

International Nuclear Information System (INIS)

Evans, J.P.; Paige, E.L.

1980-12-01

The use of Synroc as a disposal medium for magnox waste has been evaluated and three possible methods of fabrication have been investigated. Hot pressing in graphite dies has produced the highest densities - further work is proceeding on sintering and hot isostatic pressing. The leach test results have indicated that the lowest density samples have adequate leach resistance while the higher density samples are an order of magnitude better. (author)

Corrosion of technical ceramics by molten aluminium

NARCIS (Netherlands)

Schwabe, U.; Wolff, L.R.; Loo, van F.J.J.; Ziegler, G.

1992-01-01

The corrosion of 8 types of ceramics, i.e., 1 grade of hot isostatically pressed reaction-bonded Si3N4 (HIPRBSN), 3 grades of hot pressed Si3N4 (HPSN), and 4 grades of RBSN, and 2 types of SiC (HIPSiC and Si-impregnated SiC (SiSiC)) in molten Al (pure Al and AlZnMgCu1.5) was studied. The HIPRBSN and

Flexible Description Language for HPC based Processing of Remote Sense Data

Science.gov (United States)

Nandra, Constantin; Gorgan, Dorian; Bacu, Victor

2016-04-01

information: [1] Gorgan, D., "Flexible and Adaptive Processing of Earth Observation Data over High Performance Computation Architectures", International Conference and Exhibition Satellite 2015, August 17-19, Houston, Texas, USA. [2] Bigearth project - flexible processing of big earth data over high performance computing architectures. http://cgis.utcluj.ro/bigearth, (2014) [3] Nandra, C., Gorgan, D., "Workflow Description Language for Defining Big Earth Data Processing Tasks", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp. 461-468, (2015). [4] Bacu, V., Stefan, T., Gorgan, D., "Adaptive Processing of Earth Observation Data on Cloud Infrastructures Based on Workflow Description", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp.444-454, (2015). [5] Mihon, D., Bacu, V., Colceriu, V., Gorgan, D., "Modeling of Earth Observation Use Cases through the KEOPS System", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp. 455-460, (2015).

Pre-brazed casting and hot radial pressing: A reliable process for the manufacturing of CFC and W monoblock mock-ups

International Nuclear Information System (INIS)

Visca, Eliseo; Libera, S.; Mancini, A.; Mazzone, G.; Pizzuto, A.; Testani, C.

2007-01-01

ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and, in particular, for the manufacturing of high heat flux plasma-facing components (HHFC), such as the divertor targets, the baffles and the limiters. During last years, ENEA has manufactured actively cooled mock-ups by using different technologies, namely brazing, diffusion bonding and hot isostatic pressing (HIPping). A new manufacturing process has been set up and tested. It was successfully applied for the manufacturing of W armoured monoblock mock-ups. This technique is the HRP (hot radial pressing) based on performing a radial diffusion bonding between the cooling tube and the armour tile by pressurizing only internal tube and by keeping the joining zone in vacuum at the required bonding temperature. The heating is obtained by a standard air furnace. The HRP technique is now used for the manufacturing of CFC armoured monoblock components. For this purpose, some issues have to be faced, like the low CFC tensile strength, the pure copper interlayer between the heat sink and the armour necessary to mitigate the stress at the joint interface, and the low wettability of the pure copper on the CFC matrix. This paper reports the research path followed to manufacture a medium scale vertical target CFC and W armoured mock-up by HRP. A casting of a soft copper interlayer between the tube and the tile was obtained by a new technique: the pre-brazed casting (PBC, ENEA patent). Some preliminary mock-ups with three NB31 CFC tiles were successfully manufactured and tested to thermal fatigue using electron beam facilities. They all reached at least 1000 cycles at 20 MW/m 2 without suffering any damage. The manufactured medium scale vertical target mock-up is now under testing at the FE2000 (France) facility. These activities were performed in the frame of ITER-EFDA contracts

Optimization of the process of pressing safflower seeds in an ultrasonic field

Directory of Open Access Journals (Sweden)

S. T. Antipov

2017-01-01

Full Text Available The article gives a mathematical description of the process of pressing safflower seeds in an ultrasonic field in the form of a regression equation found by static methods on the basis of experiments and described by a polynomial of the second degree. As the main factors influencing the efficiency of the process, the ultrasound frequency, the amplitude of the ultrasound, the pressure and the press created in the green chamber were selected. And as a criterion for assessing the effect of the selected parameters, the residual oil content of the cake is used. To assess the adequacy of the mathematical model, the variance analysis (ANOVA of the experiment in the Design Expert v. 10 and the regression equation is obtained, the analysis of which allowed us to identify the factors that most influenced the process under consideration. Found that when the pressure in the press to a value higher than 14 MPa, a further increase in efficiency was observed together with increased values as the ultrasound frequency and its amplitude. The maximum and most effective value residual oil content in oil cake obtained in the frequency 35-40 Hz and amplitude of more than 40 mm and the pressure in the press from 10 to 11 MPa. which are obviously directly dependent on the behavior of grain and movement of its internal parts during the supply of the ultrasound. Graphical interpretation of the equation is represented by curves of equal values and response surfaces for input parameters. A numerical and graphical optimization procedure is also proposed to predict the optimal level of input factors and to obtain the maximum yield of oil relative to the mass of the original feed. To test the adequacy of the model, the results of a number of parallel experiments are presented that fall within the calculated confidence intervals for all quality criteria.

Effect of Zr on dielectric, ferroelectric and impedance properties of ...

Indian Academy of Sciences (India)

Administrator

4Department of Physics and Astrophysics, University of Delhi, Delhi 110 007, India. MS received 11 April 2010 ... (Park and Shrout 1997; Fu and Cohen 2000; Mahajan et al 2009). ... sure of 200 MPa using a Cold Isostatic Press (M/s Auto-.

Compaction creep of quartz sand at 400-600°C: Experimental evidence for dissolution-controlled pressure solution

NARCIS (Netherlands)

Niemeijer, A.; Spiers, C.J.; Bos, B.

2002-01-01

Intergranular pressure solution (IPS) is an important compaction and deformation mechanism in quartzose rocks, but the kinetics and rate-controlling process remain unclear. The aim of the present study is to test microphysical models for compaction creep by IPS against isostatic hot pressing

Effect of processing on fracture toughness of silicon carbide as determined by Vickers indentations

Science.gov (United States)

Dannels, Christine M.; Dutta, Sunil

1989-01-01

Several alpha-SiC materials were processed by hot isostatic pressing (HIPing) and by sintering an alpha-SiC powder containing boron and carbon. Several beta-SiC materials were processed by HIPing a beta-SiC powder with boron and carbon additions. The fracture toughnesses K(sub 1c) of these beta- and alpha-SiC materials were estimated from measurements of Vickers indentations. The three formulas used to estimate K(sub 1c) from the indentation fracture patterns resulted in three ranges of K(sub 1c) estimates. Furthermore, each formula measured the effects of processing differently. All three estimates indicated that fine-grained HIPed alpha-SiC has a higher K(sub 1c) than coarsed-grained sintered alpha-SiC. Hot isostatically pressed beta-SiC, which had an ultrafine grain structure, exhibited a K(sub 1c) comparable to that of HIPed alpha-SiC.

Incineration ash conditioning processes

International Nuclear Information System (INIS)

Jouan, A.; Ouvrier, N.; Teulon, F.

1990-01-01

Incinerable wastes consist of the following standard composition corresponding to projected wastes from a future mixed oxide fuel fabrication plant with an annual throughput of 1700 kg (i.e. 5.7 m 3 ) of ashes produced by the incineration facility: . 50% polyvinyl chloride (glove box sleeves), . 5% polyethylene (bags), . 35% rubber (equal amounts of latex and neoprene), . 10% cellulose (equal amounts of cotton and cleansing tissues). The work focused mainly on compaction by high-temperature isostatic pressing, is described in some detail with the results obtained. An engineering study was also carried out to compare this technology with two other ash containment processes: direct-induction (cold crucible) melting and cement-resin matrix embedding. Induction melting is considerably less costly than isostatic pressing; the operating costs are about 1.5 times higher than for cement-resin embedding, but the volume reduction is nearly 3 times greater

A thermal engine for underwater glider driven by ocean thermal energy

International Nuclear Information System (INIS)

Yang, Yanan; Wang, Yanhui; Ma, Zhesong; Wang, Shuxin

2016-01-01

Highlights: • Thermal engine with a double-tube structure is developed for underwater glider. • Isostatic pressing technology is effective to increase volumetric change rate. • Actual volumetric change rate reaches 89.2% of the theoretical value. • Long term sailing of 677 km and 27 days is achieved by thermal underwater glider. - Graphical Abstract: - Abstract: Underwater glider is one of the most popular platforms for long term ocean observation. Underwater glider driven by ocean thermal energy extends the duration and range of underwater glider powered by battery. Thermal engine is the core device of underwater glider to harvest ocean thermal energy. In this paper, (1) model of thermal engine was raised by thermodynamics method and the performance of thermal engine was investigated, (2) thermal engine with a double-tube structure was developed and isostatic pressing technology was applied to improve the performance for buoyancy driven, referencing powder pressing theory, (3) wall thickness of thermal engine was optimized to reduce the overall weight of thermal engine, (4) material selection and dimension determination were discussed for a faster heat transfer design, by thermal resistance analysis, (5) laboratory test and long term sea trail were carried out to test the performance of thermal engine. The study shows that volumetric change rate is the most important indicator to evaluating buoyancy-driven performance of a thermal engine, isostatic pressing technology is effective to improve volumetric change rate, actual volumetric change rate can reach 89.2% of the theoretical value and the average power is about 124 W in a typical diving profile. Thermal engine developed by Tianjin University is a superior thermal energy conversion device for underwater glider. Additionally, application of thermal engine provides a new solution for miniaturization of ocean thermal energy conversion.

Lithospheric thickness jumps at the S-Atlantic continental margins from satellite gravity data and modelled isostatic anomalies

Science.gov (United States)

Shahraki, Meysam; Schmeling, Harro; Haas, Peter

2018-01-01

Isostatic equilibrium is a good approximation for passive continental margins. In these regions, geoid anomalies are proportional to the local dipole moment of density-depth distributions, which can be used to constrain the amount of oceanic to continental lithospheric thickening (lithospheric jumps). We consider a five- or three-layer 1D model for the oceanic and continental lithosphere, respectively, composed of water, a sediment layer (both for the oceanic case), the crust, the mantle lithosphere and the asthenosphere. The mantle lithosphere is defined by a mantle density, which is a function of temperature and composition, due to melt depletion. In addition, a depth-dependent sediment density associated with compaction and ocean floor variation is adopted. We analyzed satellite derived geoid data and, after filtering, extracted typical averaged profiles across the Western and Eastern passive margins of the South Atlantic. They show geoid jumps of 8.1 m and 7.0 m for the Argentinian and African sides, respectively. Together with topography data and an averaged crustal density at the conjugate margins these jumps are interpreted as isostatic geoid anomalies and yield best-fitting crustal and lithospheric thicknesses. In a grid search approach five parameters are systematically varied, namely the thicknesses of the sediment layer, the oceanic and continental crusts and the oceanic and the continental mantle lithosphere. The set of successful models reveals a clear asymmetry between the South Africa and Argentine lithospheres by 15 km. Preferred models predict a sediment layer at the Argentine margin of 3-6 km and at the South Africa margin of 1-2.5 km. Moreover, we derived a linear relationship between, oceanic lithosphere, sediment thickness and lithospheric jumps at the South Atlantic margins. It suggests that the continental lithospheres on the western and eastern South Atlantic are thicker by 45-70 and 60-80 km than the oceanic lithospheres, respectively.

Medicine and health information in Galician daily press. The health news in the main Galician newspapers

Directory of Open Access Journals (Sweden)

Lic. Carmen Costa Sánchez

2008-01-01

Full Text Available The aim of this paper is to study the health and medicine information published during a week in the four newspapers more spreaded in Galicia. The journalism has the responsibility of informing about health with quality criterions, instead of considering health a superficial, anecdotic and secondary subject. The appearance of the specific sections and the incorporation of the journalists specialized in health to the editorial staffs of the Spanish main generalist newspapers are beginning a process in depth in this way. But what is happening with the press of the autonomous regions? Which is the informative processing of medicine and health information in Galician daily press?, we asked. Descriptive, quantitative and content analysis will make possible to think about the information coverage of this kind of facts for making a diagnostic of the situation and for proposing its necessary improvement.

Indre spenninger og ytre press

DEFF Research Database (Denmark)

Ibsen, Bjarne

2011-01-01

Anmeldelse af bogen 'Norsk idrett. Indre spenninger og ytre press' redigeret af Dag Vidar Hanstad, Gunnar Breivik, Mari Kristin Sisjord og Hans B. Skaset og udgivet af forlaet akilles.......Anmeldelse af bogen 'Norsk idrett. Indre spenninger og ytre press' redigeret af Dag Vidar Hanstad, Gunnar Breivik, Mari Kristin Sisjord og Hans B. Skaset og udgivet af forlaet akilles....

WordPress 3 Cookbook

CERN Document Server

Shreves, Ric

2011-01-01

This is a Packt Cookbook, which means it contains step-by-step instructions to achieve a particular goal or solve a particular problem. There are plenty of screenshots and explained practical tasks to make comprehension quick and easy. This book is not specifically for developers or programmers; rather it can be used by anyone who wants to get more out of their WordPress blog by following step-by-step instructions. A basic knowledge of PHP/XHTML/CSS/WordPress is desirable but not necessary.

Data on the influence of cold isostatic pre-compaction on mechanical properties of polycrystalline nickel sintered using Spark Plasma Sintering

Directory of Open Access Journals (Sweden)

Guy-Daniel Dutel

2017-04-01

Full Text Available Data regarding bulk polycrystalline nickel samples obtained by powder metallurgy using Spark Plasma Sintering (SPS are presented, with a special emphasis on the influence of a cold isostatic pre-compaction on the resulting morphologies and subsequent mechanical properties. Three types of initial powders are used, nanometric powders, micrometric powders and a mixture of the formers. For each type of powder, the SPS cycle has been optimized for the powders without pre-compaction and the same cycle has been used to also sinter pre-compacted powders.

WordPress all-in-one for dummies

CERN Document Server

Sabin-Wilson, Lisa; Palmer, Kevin

2011-01-01

A convenient how-to guide for maximizing your WordPress experience. WordPress is a state-of-the-art blog publishing platform with nearly ten million active installations. Eight minibooks provide you with expanded coverage of the most important topics to the WordPress community, such as WordPress basics, theme designs, plug-in development, social media integration, SEO, customization, and running multiple sites. Veteran author Lisa Sabin-Wilson leads an authoritative team of authors who offer their unique knowledge and skillset while sharing invaluable advice for maximizing your site's potentia

Effect of hot pressing additives on the leachability of hot pressed sodium hydrous titanium oxide

International Nuclear Information System (INIS)

Valentine, T.M.; Sambell, R.A.J.

1980-01-01

Sodium hydrous titanium oxide is an ion exchange resin which can be used for immobilizing medium level waste (MLW) liquors. When hot pressed, it undergoes conversion to a ceramic. Three low melting point materials (borax, bismuth trioxide, and a mixture of PbO/CuO) were added to the (Na)HTiO and the effect that each of these had on aiding densification was assessed. Hot pressing temperature, applied pressure, and percentage addition of hot pressing aid were varied. Percentage open porosity, flexural strength, and leachability were measured. There was a linear relationship between the percentage open porosity and the logarithm of the leach rate for a constant percentage addition of each additive

Study of pore closure during pressure-less sintering of advanced oxide ceramics

Czech Academy of Sciences Publication Activity Database

Spusta, T.; Svoboda, Jiří; Maca, K.

2016-01-01

Roč. 115, AUG (2016), s. 347-353 ISSN 1359-6454 R&D Projects: GA ČR(CZ) GA15-06390S Institutional support: RVO:68081723 Keywords : Ceramic material * Sintering * Porosity * Modelling * Hot isostatic pressing Subject RIV: BJ - Thermodynamics Impact factor: 5.301, year: 2016

Gravity and isostatic anomaly maps of Greece produced

Science.gov (United States)

Lagios, E.; Chailas, S.; Hipkin, R. G.

A gravity anomaly map of Greece was first compiled in the early 1970s [Makris and Stavrou, 1984] from all available gravity data collected by different Hellenic institutions. However, to compose this map the data had to be smoothed to the point that many of the smaller-wavelength gravity anomalies were lost. New work begun in 1987 has resulted in the publication of an updated map [Lagios et al., 1994] and an isostatic anomaly map derived from it.The gravity data cover the area between east longitudes 19° and 27° and north latitudes 32° and 42°, organized in files of 100-km squares and grouped in 10-km squares using UTM zone 34 coordinates. Most of the data on land come from the gravity observations of Makris and Stavrou [1984] with additional data from the Institute of Geology and Mining Exploration, the Public Oil Corporation of Greece, and Athens University. These data were checked using techniques similar to those used in compiling the gravity anomaly map of the United States, but the horizontal gradient was used as a check rather than the gravity difference. Marine data were digitized from the maps of Morelli et al. [1975a, 1975b]. All gravity anomaly values are referred to the IGSN-71 system, reduced with the standard Bouger density of 2.67 Mg/m3. We estimate the errors of the anomalies in the continental part of Greece to be ±0.9 mGal; this is expected to be smaller over fairly flat regions. For stations whose height has been determined by leveling, the error is only ±0.3 mGal. For the marine areas, the errors are about ±5 mGal [Morelli, 1990].

Pellet presses for remote fuel fabrication

International Nuclear Information System (INIS)

Densley, P.J.

1978-01-01

Two types of mechanical presses are being tested from the remote operation and remote maintenance aspects. Results will be used to recommend the type of press and design considerations required for operation in a remotely operated and maintained process line

A study of pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing on properties of aluminium/alumina nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Abedinzadeh, Reza; Safavi, Seyed Mohsen; Karimzadeh, Fathallah [Isfahan University, Isfahan (Iran, Islamic Republic of)

2016-05-15

Bulk Al/4wt-%Al{sub 2}O{sub 3} nanocomposites were prepared by consolidating nanocomposite powders using pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing techniques. Microstructural observations revealed that the microwave-assisted hot press sintering at different sintering temperatures of 400.deg.C and 500.deg.C resulted in more densification and smaller grain size for Al/Al{sub 2}O{sub 3} nanocomposite as compared with the conventional hot pressing. Moreover, the application of pressure in microwave sintering process led to more densification and grain growth. Mechanical properties resulting from microhardness and nanoindentation tests were also compared between three-method processed samples. It was found that the microwave-assisted hot-pressed sample exhibited higher hardness and elastic modulus in comparison with microwave-sintered and conventional hot-pressed samples. The improvement in the mechanical properties can be ascribed to lower porosity of microwave-assisted hot-pressed sample.

Crystallization and properties of Sr-Ba aluminosilicate glass-ceramic matrices

Science.gov (United States)

Bansal, Narottam P.; Hyatt, Mark J.; Drummond, Charles H., III

1991-01-01

Powders of roller quenched (Sr,Ba)O-Al2O3-2SiO2 glasses of various compositions were uniaxially pressed into bars and hot isostatically pressed at 1350 C for 4 hours or cold isostatically pressed and sintered at different temperatures between 800 to 1500 C for 10 or 20 hours. Densities, flexural strengths, and linear thermal expansion were measured for three compositions. The glass transition and crystallization temperatures were determined by Differential Scanning Calorimetry (DSC). The liquidus and crystallization temperature from the melt were measured using high temperature Differential Thermal Analysis (DTA). Crystalline phases formed on heat treatment of the glasses were identified by powder X ray diffraction. In Sr containing glasses, the monoclinic celsian phase always crystallized at temperatures above 1000 C. At lower temperatures, the hexagonal analog formed. The temperature for orthorhombic to hexagonal structural transformation increased monotonically with SrO content, from 327 C for BaO-Al2O3-2SiO2 to 758 C for SrO-Al2O3-2SiO2. These glass powders can be sintered to almost full densities and monoclinic celsian phase at a relatively low temperature of 1100 C.

Densification and Grain Growth in Polycrystalline Olivine Rocks Synthesized By Evacuated Hot-Pressing

Science.gov (United States)

Meyers, C. D.; Kohlstedt, D. L.; Zimmerman, M. E.

2017-12-01

Experiments on laboratory-synthesized olivine-rich rocks form the starting material for many investigations of physical processes in the Earth's upper mantle (e.g., creep behavior, ionic diffusion, and grain growth). Typically, a fit of a constitutive law to experimental data provides a description of the kinetics of a process needed to extrapolate across several orders of magnitude from laboratory to geological timescales. Although grain-size is a critical parameter in determining physical properties such as viscosity, broad disagreement persists amongst the results of various studies of grain growth kinetics in olivine-rich rocks. Small amounts of impurities or porosity dramatically affect the kinetics of grain growth. In this study, we developed an improved method for densifying olivine-rich rocks fabricated from powdered, gem-quality single crystals that involves evacuating the pore space, with the aim of refining measurements of the kinetics of mantle materials. In previous studies, olivine powders were sealed in a metal can and hydrostatically annealed at roughly 300 MPa and 1250 °C. These samples, which appear opaque and milky-green, typically retain a small amount of porosity. Consequently, when annealed at 1 atm, extensive pore growth occurs, inhibiting grain growth. In addition, Fourier-transform infrared and confocal Raman spectroscopy reveal absorption peaks characteristic of CO2 in the pores of conventionally hot-pressed material. To avoid trapping of adsorbed contaminants, we developed an evacuated hot-pressing method, wherein the pore space of powder compacts is vented to vacuum during heating and pressurization. This method produces a highly dense, green-tinted, transparent material. No CO2 absorptions peaks exist in evacuated hot-pressed material. When reheated to annealing temperatures at 1 atm, the evacuated hot-pressed material undergoes limited pore growth and dramatically enhanced grain-growth rates. High-strain deformation experiments on

Effects of pressing temperature and initial microstructure on the equal channel angular pressing of Ti-6Al-4V alloy

International Nuclear Information System (INIS)

Ko, Y.G.; Lee, Y.H.; Jung, W.S.; Shin, D.H.; Lee, C.S.

2003-01-01

The effects of pressing temperature and initial microstructure on the equal channel angular (ECA) pressing of Ti-6Al-4V alloy were investigated in this study. The ECA pressing was carried out isothermally with route C at 500 C, 600 C and 700 C for two typical microstructures, i.e., the Widmanstaetten microstructure and the equiaxed microstructure. The results showed that ECA pressing at 600 C and 700 C was successful without producing any noticeable segment at the specimen surfaces, while a large amount of surface segments were produced at 500 C. After 1 pass pressing at 600 C, the equiaxed microstructure showed more uniform material flow at the surface than the Widmanstaetten microstructure. However, this microstructural influence was diminished with increase of the number of the ECA pressing. A flow-localization parameter that quantifies the flow non-uniform tendency in case of flow softening materials was used to explain the different results in each microstructure. (orig.)

Technology for the long-term management of defense HLW at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Staples, B.A.; Berreth, J.R.; Knecht, D.A.

1986-01-01

The Defense Waste Management Plan of June 1983 includes a reference plan for the long-term management of Idaho Chemical Processing Plant (ICPP) high-level waste (HLW), with a goal of disposing of the annual output in 500 canisters a year by FY-2008. Based on the current vitrification technology, the ICPP base-glass case would produce 1700 canisters per year after FY-2007. Thus, to meet the DWMP goal processing steps including fuel dissolution, waste treatment, and waste immobilization are being studied as areas where potential modifications could result in HLW volume reductions for repository disposal. It has been demonstrated that ICPP calcined wastes can be densified by hot isostatic pressing to multiphase ceramic forms of high loading and density. Conversion of waste by hot isostatic pressing to these forms has the potential of reducing the annual ICPP waste production to volumes near those of the goal of the DWMP. This report summarizes the laboratory-scale information currently available on the development of these forms

Teach yourself visually complete WordPress

CERN Document Server

Majure, Janet

2013-01-01

Take your WordPress skills to the next level with these tips, tricks, and tasks Congratulations on getting your blog up and running with WordPress! Now are you ready to take it to the next level? Teach Yourself VISUALLY Complete WordPress takes you beyond the blogging basics with expanded tips, tricks, and techniques with clear, step-by-step instructions accompanied by screen shots. This visual book shows you how to incorporate forums, use RSS, obtain and review analytics, work with tools like Google AdSense, and much more.Shows you how to use mobile tools to edit a

Volatile organic compound emissions during hot-pressing of southern pine particleboard : panel size effects and trade-off between press time and temperature

Science.gov (United States)

Wenlong Wang; Douglas J. Gardner; Melissa G.D. Baumann

2002-01-01

In previous research, it was shown that decreasing either press temperature or press time generally resulted in decreased volatile organic compound (VOC) emissions during the hot-pressing of southern pine particleboard. However, because it is impossible to reduce both pressing time and temperature while maintaining panel physical and mechanical properties, this study...

Cold texturing of prereacted high-Tc phase Bi(Pb)SrCaCuO under triaxial stresses

International Nuclear Information System (INIS)

Langlois, P.; Massat, H.; Suryanarayanan, R.

1994-01-01

The alignment of grains in isostatically precompacted samples of prereacted Bi 1.8 Pb 0.4 Sr 2.0 Ca 2.2 Cu 3.0 O 10.3+x powder has been achieved by compressive plastic deformation under isostatic pressure at room temperature. Isostatic pressures were in the range 0.1 to 1. GPa and deformation rates were led up to 57%. Prior to sintering, X-ray diffraction measurements corroborate an expected high-Tc phase purity of nearly 85% and indicate that the as-deformed samples have been textured with the c-axes parallel to the pressing direction whilst a.c. susceptibility measurements ascertain a high transition temperature around 107 K. Intergranular connection does not occur until sintering at 850 C for 80 h and measurements indicate then that the texture has been retained. Superconducting properties themselves show sensitivity to texture through anisotropy-related distinctive irreversibility lines. (orig.)

Designing a Tool System for Lowering Friction during the Ejection of In-Die Sintered Micro Gears

DEFF Research Database (Denmark)

Cannella, Emanuele; Nielsen, Emil Krabbe; Stolfi, Alessandro

2017-01-01

is affected by the influence of friction during the ejection phase, caused by radial expansion of the compacted and sintered powder. This paper presents the development of a pre-stressed tool system for the manufacture of micro gears made of aluminum. By using the hot isostatic pressing (HIP) sintering...

WordPress web design for dummies

CERN Document Server

Sabin-Wilson, Lisa

2013-01-01

Updated, full-color guide to creating dynamic websites with WordPress 3.6 In this updated new edition, bestselling For Dummies author and WordPress expert Lisa Sabin-Wilson makes it easy for anyone with a basic knowledge of the WordPress software to create a custom site using complementary technologies such as CSS, HTML, PHP, and MySQL. You'll not only get up to speed on essential tools and technologies and further advance your own design skills, this book also gives you pages of great case studies, so you can see just how other companies and individuals are creating compelling, customized, a

Searching for a Free Press in Indian Country.

Science.gov (United States)

Benton, Sherrole

1994-01-01

Describes the tribally controlled media's efforts to provide a form of checks and balances against the tribal council on behalf of the tribal community. Examines the issue of freedom of the tribal press, suggesting that tribal council's control of press's operating funds may limit press freedom. (MAB)

Graphic Arts: Book Three. The Press and Related Processes.

Science.gov (United States)

Farajollahi, Karim; And Others

The third of a three-volume set of instructional materials for a graphic arts course, this manual consists of nine instructional units dealing with presses and related processes. Covered in the units are basic press fundamentals, offset press systems, offset press operating procedures, offset inks and dampening chemistry, preventive maintenance…

Pre-Brazed Casting and Hot Radial Pressing: A Reliable Process for the Manufacturing of CFC and W Monoblock Mockups

International Nuclear Information System (INIS)

Visca, E.; Libera, S.; Mancini, A.; Mazzone, G.; Pizzuto, A.; Testani, C.

2006-01-01

ENEA association is involved in the European International Thermonuclear Experimental Reactor (ITER) R-and-D activities and in particular for the manufacturing of high heat flux plasma-facing components (HHFC), such as the divertor targets, the baffles and the limiters: During the last years ENEA has manufactured actively cooled mock-ups by using different technologies, namely brazing, diffusion bonding and hot isostatic pressing (HIPping). A new manufacturing process has been set up and tested. It was successfully applied for the manufacturing of W armoured monoblock mockups. This technique is the HRP (Hot Radial Pressing) based on performing a radial diffusion bonding between the cooling tube and the armour tile by pressurizing only the internal tube and by keeping the joining zone in vacuum and at the required bonding temperature. The heating is obtained by a standard air furnace. The next step was to apply the HRP technique for the manufacturing of CFC armoured monoblock components. For this purpose some issues have to be solved like as the low CFC tensile strength, the pure copper interlayer between the heat sink and the armour necessary to mitigate the stress at the joint interface and the low wettability of the pure copper on the CFC matrix. This paper reports the research path followed to manufacture a medium scale vertical target CFC and W armoured mockup by HRP. An ad hoc rig able to maintain the CFC in a compressive constant condition was also designed and tested. The casting of a soft copper interlayer between the tube and the tile was performed by a new technique: the Pre-Brazed Casting (PBC, ENEA patent). Some mock-ups with three NB31 CFC tiles were successfully manufactured and tested to thermal fatigue using electron beam facilities. They all reached at least 1000 cycles at 20 MW/m 2 without suffering any damage. The manufactured medium scale vertical target mock-up is now under testing at the FE2000 (France) facility. (author)

The Mediated Amplification of a Crisis: Communicating the A/H1N1 Pandemic in Press Releases and Press Coverage in Europe.

Science.gov (United States)

Rossmann, Constanze; Meyer, Lisa; Schulz, Peter J

2018-02-01

In the aftermath of the A/H1N1 pandemic, health authorities were criticized for failures in crisis communication efforts, and the media were accused of amplifying the pandemic. Considering these criticisms, A/H1N1 provides a suitable case for examining risk amplification processes that may occur in the transfer of information from press releases to print news media during a health crisis. We integrated the social amplification of risk framework with theories of news decisions (news values, framing) in an attempt to contribute to existing research both theoretically and empirically. We conducted a quantitative content analysis of press releases disseminated by health and governmental authorities, as well as the quality and tabloid press in 10 European countries between March 2009 and March 2011. Altogether 243 press releases, 1,243 quality press articles, and 834 tabloid press articles were coded. Consistent with research on news values and framing the results suggest that quality and tabloid papers alike amplified A/H1N1 risks by emphasizing conflict and damage, presenting information in a more dramatized way, and using risk-amplifying frames to a greater extent and risk-attenuating frames to a lesser extent than press releases. To some extent, the quality and tabloid press differed in how risk information was presented. While tabloid press articles seemed to follow the leading quality press with regards to content and framing of health crisis coverage, they exhibited a stronger emphasis on drama and emotion in the way they presented information. © 2017 Society for Risk Analysis.

OAS :: Press Releases

Science.gov (United States)

subscriptions Videos Photos Live Webcast Social Media Facebook @oasofficial Facebook Twitter @oas_official Social Media Facebook Twitter Newsletters Press and Communications Department Contact us at: +1 (202) 370 Rights Actions against Corruption C Children Civil Registry Civil Society Contact Us Culture Cyber

DSS / Press Room

Science.gov (United States)

Defense Security Service, U.S. Department of Defense Site Map | A-Z Index | Facebook | Twitter Locations Press Room Organizational Structure Careers at DSS Doing Business with DSS Frequently Asked Classification System (NCCS) National Industrial Security System (NISS) ODAA Business Management System (OBMS

PRESS FREEDOM IN SINGAPORE AND MALAYSIA: DEFAMATION

OpenAIRE

Georgia Kate Chapman

2015-01-01

This paper focuses on the arguments around restriction on freedom of the press in the Strong States of Singapore and Malaysia. It assesses the presence of constraints on press freedoms in democratic western countries imposed by corporation rather than state and the similar effects that these constraints may have on bias present in publicly accessible news reporting. It argues that independence of the press does not just require protection from legal and executive regulation, but also protecti...

Glacial isostatic adjustment on the Northern Hemisphere - new results from GRACE

Science.gov (United States)

Mueller, J.; Steffen, H.; Gitlein, O.; Denker, H.; Timmen, L.

2007-12-01

The Earth's gravity field mapped by the Gravity Recovery and Climate Experiment (GRACE) satellite mission shows variations due to the integral effect of mass variations in the atmosphere, hydrosphere and geosphere. The Earth's gravity field is provided in form of monthly solutions by several institutions, e.~g. GFZ Potsdam, CSR and JPL. During the GRACE standard processing of these analysis centers, oceanic and atmospheric contributions as well as tidal effects are reduced. The solutions of the analysis centers differ slightly, which is due the application of different reduction models and center-specific processing schemes. We present our investigation of mass variations in the areas of glacial isostatic adjustment (GIA) in North America and Northern Europe from GRACE data. One key issue is the separation of GIA parts and the reduction of the observed quantities by applying dedicated filters (e.~g. isotropic, non-isotropic, and destriping filters) and global models of hydrological variations (e.~g. WGHM, LaDWorld, GLDAS). In a further step, we analyze the results of both regions regarding their reliability, and finally present a comparison to results of a geodynamical modeling and absolute gravity measurements. Our results clearly show that the quality of the GRACE-derived gravity- change signal benefits from improved reduction models and chosen analysis techniques. Nevertheless, the comparison to results of geodynamic models still reveals differences, and thus further studies are in progress.

Teenagers as Victims in the Press

Science.gov (United States)

Andersson, Gunvor; Lundstrom, Tommy

2007-01-01

Research into press reporting on young people has tended to concentrate on young people as offenders. In contrast, this article focuses on press coverage of teenagers as victims. Reports in two Swedish newspapers (a morning broadsheet and an evening tabloid) were studied over a period of four months and subjected to a qualitative analysis of…

Hot pressing of B4C/SiC composites

International Nuclear Information System (INIS)

Sahin, F.C.; Turhan, E.; Yesilcubuk, S.A.; Addemir, O.

2005-01-01

B 4 C/SiC ceramic composites containing 10-20-30 vol % SiC were prepared by hot pressing method. The effect of SiC addition and hot pressing temperature on sintering behaviour and mechanical properties of hot pressed composites were investigated. Microstructures of hot pressed samples were examined by SEM technique. Three different temperatures (2100 deg. C, 2200 deg. C and 2250 deg. C) were used to optimize hot pressing temperature applying 100 MPa pressure under argon atmosphere during the sintering procedure. The highest relative density of 98.44 % was obtained by hot pressing at 2250 deg. C. However, bending strengths of B 4 C/SiC composite samples were lower than monolithic B 4 C in all experimental conditions. (authors)

The small academic press in the land of giants

Directory of Open Access Journals (Sweden)

Frances Pinter

2015-11-01

Full Text Available Mergers and acquisitions, for example the merger of Macmillan Science and Education with Springer Science+Business Media, might suggest that large is the future for academic publishing.  It might seem that giant players will dominate the future of scholarly publishing, but, at the same time, this year has seen the launch of UCL Press, the University’s in-house publishing arm. Goldsmiths, University of London, has also announced it is preparing to launch Goldsmiths Press, a new university press built on digital-first publishing, especially around unconventional projects traditionally excluded by publishers. Some of the more established university presses also seem to be increasing their scope. For example, Stanford University Press launched a new trade imprint and Manchester University Press has announced it has acquired forward titles from Bloomsbury Publishing.  'Insights 'asked two experts if there really is scope for the small academic press in the modern scholarly publishing environment. Frances Pinter has provided the perspective of the small university press. She is realistic about the challenges small academic publishers face, but concludes that there is space and opportunity for them to coexist with the giants. Michael Magoulias is equally realistic about the challenges of small, but sees the university press as a necessary, not to say, vital, alternative to commercial publishing.

Elbow joint fatigue and bench-press training.

Science.gov (United States)

Huang, Yen-Po; Chou, You-Li; Chen, Feng-Chun; Wang, Rong-Tyai; Huang, Ming-Jer; Chou, Paul Pei-Hsi

2014-01-01

Bench-press exercises are among the most common form of training exercise for the upper extremity because they yield a notable improvement in both muscle strength and muscle endurance. The literature contains various investigations into the effects of different bench-press positions on the degree of muscle activation. However, the effects of fatigue on the muscular performance and kinetics of the elbow joint are not understood fully. To investigate the effects of fatigue on the kinetics and myodynamic performance of the elbow joint in bench-press training. Controlled laboratory study. Motion research laboratory. A total of 18 physically healthy male students (age = 19.6 ± 0.8 years, height = 168.7 ± 5.5 cm, mass = 69.6 ± 8.6 kg) participated in the investigation. All participants were right-hand dominant, and none had a history of upper extremity injuries or disorders. Participants performed bench-press training until fatigued. Maximal possible number of repetitions, cycle time, myodynamic decline rate, elbow-joint force, and elbow-joint moment. We observed a difference in cycle time in the initial (2.1 ± 0.42 seconds) and fatigue (2.58 ± 0.46 seconds) stages of the bench-press exercise (P = .04). As the participants fatigued, we observed an increase in the medial-lateral force (P = .03) and internal-external moment (P ≤ .04) acting on the elbow joint. Moreover, a reduction in the elbow muscle strength was observed in the elbow extension-flexion (P ≤ .003) and forearm supination-pronation (P ≤ .001) conditions. The results suggest that performing bench-press exercises to the point of fatigue increases elbow-joint loading and may further increase the risk of injury. Therefore, when clinicians design bench-press exercise regimens for general athletic training, muscle strengthening, or physical rehabilitation, they should control carefully the maximal number of repetitions.

The feasibility of bonding aluminum alloy 6061 via hot isostatic pressing (HIP)/rolling

International Nuclear Information System (INIS)

Fenolietto, R.A.

1991-01-01

The advantage of developing a HIP bonding process for dispersion fuel plates is that applying a thin cladding in a more uniform manner could allow the upper limit for LEU U 3 Si-Al dispersion fuel plate densities to be overcome. Since much less mechanical deformation would be required, the existing process limitations on the density could be removed, theoretically allowing more fuel to be added. These increases are, of course, subject to irradiation behavior of the higher loadings which is not addressed in this paper. Initial results indicate that aluminum Alloy 6061 can be successfully bonded by seal welding via electron beam (EB), HIPping, and finishing with a limited amount of rolling. (orig.)

Influence of purity level on the mechanical properties of hot isostatically pressed beryllium

International Nuclear Information System (INIS)

Odegard, B.C. Jr.

1979-09-01

The procurement of a quantity of ultra-pure beryllium powder combined with special handling from powder to billet form resulted in the fabrication of high purity beryllium. The mechanical properties of these billets were contrasted to those of commercial grade billets to determine the influence of impurities and powder processing. The tensile test results show that the strength values are primarily dependent on the grain size in a behavior predictable by the Hall-Petch relationship. Only a fraction of the strength differential can be attributed to metallic impurities in solution. The grain size is controlled by the powder size distribution. The ductility is dominated by both grain size and oxide content. The fine grained, low oxide billets exhibited the highest ductilities. There is evidence to suggest that oxide distribution has a large influence on the ductility. The fracture toughness was highest for the high purity beryllium billets

High density high-TC ceramic superconductors by hot pressing

International Nuclear Information System (INIS)

Mak, S.; Chaklader, A.C.D.

1989-01-01

High density and high T C superconductor specimens, YBa 2 Cu 3 O x , have been produced by hot-pressing. The factors studied are the effect of hot pressing on the density, the oxygen stoichiometry, the crystal structure, and the critical temperature. Hot pressing followed by heat treatment increased the density of the specimen to 93%. The hot pressing itself did not significantly affect the oxygen content in the specimen, and although the crystal structure appeared to be orthorhombic, the specimens were not superconducting above liquid nitrogen temperature. The superconductivity was restored after head treatment in oxygen. The highest critical temperature (T C ) of the hot pressed pellets was 82K, which was slightly lower than the T C that could be obtained with the cold pressed/sintered pellets. (6 refs., 5 figs., tab.)

A new casting defect healing technology

Energy Technology Data Exchange (ETDEWEB)

Hodge, E.S.; Reddoch, T.W. [ForMat Industries, Inc., Knoxville, TN (United States); Viswanathan, S. [Oak Ridge National Lab., TN (United States)

1997-01-01

A new technology is presented for healing of defects in 356 aluminium alloys that provides economic upgrading of these cast alloys. It uses pneumatic isostatic forging (PIF) to produce high quality Al alloys products with enhanced mechanical properties uniform throughout the part, allowing higher design allowables and increased usage of Al alloy castings. The fundamental mechanism underlying PIF is a single mode plastic deformation process that uses isostatic application of pressures for 10-30 seconds at temperature. The process can be integrated in-line with other production operations, i.e., using the latent heat from the previous casting step. Results of applying the PIF process indicate lower cost and significant improvement in mechanical properties that rival and often exceed corresponding properties of other technologies like hot isostatic pressing and related processes. This process offers many advantages that are described in this paper in addition to presenting case histories of property enhancement by PIF and the mechanism responsible for property enhancement.

Pre-brazed casting and hot radial pressing: A reliable process for the manufacturing of CFC and W monoblock mock-ups

Energy Technology Data Exchange (ETDEWEB)

Visca, Eliseo [Associazione EURATOM-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi, 45, IT-00044 Frascati, RM (Italy)], E-mail: visca@frascati.enea.it; Libera, S.; Mancini, A.; Mazzone, G.; Pizzuto, A. [Associazione EURATOM-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi, 45, IT-00044 Frascati, RM (Italy); Testani, C. [CSM S.p.A., IT-00128 Castel Romano, RM (Italy)

2007-10-15

ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and, in particular, for the manufacturing of high heat flux plasma-facing components (HHFC), such as the divertor targets, the baffles and the limiters. During last years, ENEA has manufactured actively cooled mock-ups by using different technologies, namely brazing, diffusion bonding and hot isostatic pressing (HIPping). A new manufacturing process has been set up and tested. It was successfully applied for the manufacturing of W armoured monoblock mock-ups. This technique is the HRP (hot radial pressing) based on performing a radial diffusion bonding between the cooling tube and the armour tile by pressurizing only internal tube and by keeping the joining zone in vacuum at the required bonding temperature. The heating is obtained by a standard air furnace. The HRP technique is now used for the manufacturing of CFC armoured monoblock components. For this purpose, some issues have to be faced, like the low CFC tensile strength, the pure copper interlayer between the heat sink and the armour necessary to mitigate the stress at the joint interface, and the low wettability of the pure copper on the CFC matrix. This paper reports the research path followed to manufacture a medium scale vertical target CFC and W armoured mock-up by HRP. A casting of a soft copper interlayer between the tube and the tile was obtained by a new technique: the pre-brazed casting (PBC, ENEA patent). Some preliminary mock-ups with three NB31 CFC tiles were successfully manufactured and tested to thermal fatigue using electron beam facilities. They all reached at least 1000 cycles at 20 MW/m{sup 2} without suffering any damage. The manufactured medium scale vertical target mock-up is now under testing at the FE2000 (France) facility. These activities were performed in the frame of ITER-EFDA contracts.

Internet Marketing with WordPress

CERN Document Server

Mercer, David

2011-01-01

The book's accompanying Interactive learning environment on siteprebuilder.com gives you an online place to enhance and extend your practical experience through exercises, consolidate your learning and theoretical knowledge with marked quizzes, interaction with your WordPress marketing community, and fun and exciting extras such as challenges and competitions. This book is for people already using WordPress, who want more visitors, better visitors, and to convert more of them into paying customers. No prior marketing experience is required, although a basic understanding of either hosted or se

Influence of the "Slingshot" bench press training aid on bench press kinematics and neuromuscular activity in competitive powerlifters.

Science.gov (United States)

Dugdale, James H; Hunter, Angus; Di Virgilio, Thomas; Macgregor, Lewis J; Hamilton, D Lee

2017-02-13

This study examined the acute effects of the 'Slingshot' on bench-press performance, prime-mover surface electromyographic (sEMG) amplitude, and barbell velocity during maximal and submaximal bench-pressing in competitive male powerlifters. Fifteen male powerlifters (mean ± SD age: 27.05 ± 5.94 years; mass: 94.15kg; 1RM bench-press: 139.7 ± 16.79kg) participated in the study. Bench-press strength, average barbell velocity, and sEMG amplitude of the prime mover muscles (triceps brachii, pectoralis major and anterior deltoid) were measured during two conditions; 'Raw' (without use of any assistance) and 'Slingshot' [using the 'Slingshot' to perform both the weight achieved during 'Raw' 1RM testing (Raw max/SS), and absolute 1RM using the 'Slingshot' (SS)]. The results showed that the 'Slingshot' significantly increased bench press 1RM performance by a mean ± SD of 20.67kg ± 3.4kg. Barbell velocity and stick point analysis indicate that this improvement is likely driven by an increase in peak and pre-stick barbell velocity as triceps RMS was lower throughout all rep max phases with the 'Slingshot'. The 'Slingshot' also caused reductions in RMS, specifically of the triceps at all rep ranges but barbell velocity was better maintained in the last reps of all sets. These data indicate that the 'Slingshot' specifically de-loaded the triceps muscle throughout all rep ranges and provide assistance to maintaining barbell velocity under fatigue during later repetitions of multiple-repetition sets. The 'Slingshot' training aid could therefore be used in de-load phases of bench press training or as an over-reaching and velocity training aid.

Denmark, Democracy and the Free Press

DEFF Research Database (Denmark)

Breiting, Søren

2006-01-01

What's important to Danish people in Denmark and in the world - most will argue for the importance of a free critical press, solidarity with people who need help and a peaceful world.......What's important to Danish people in Denmark and in the world - most will argue for the importance of a free critical press, solidarity with people who need help and a peaceful world....

Research and development of advanced ceramics in the Materials Division of IPD in Aerospatial Technical Center

International Nuclear Information System (INIS)

Piorino Neto, F.; Melo, F.C.L. de; Cairo, C.A.A.

1988-01-01

Some informations about the I Phase of Special Ceramic Design are described, including three aim: 1) the development of the isostatic pressing process for molding and sintering of alumina 2) the development of methodology to mechanical properties characterization 3) development and control to preparation of zirconia reactive powder. (C.G.C.) [pt

Anisotropic Material Behavior of Uni-axially Compacted Graphite Matrix for HTGR Fuel Compact Fabrication

Energy Technology Data Exchange (ETDEWEB)

Lee, Young-Woo; Yeo, Seunghwan; Yoon, Ji-Hae; Cho, Moon Sung [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In developing the fuel compact fabrication technology, and fuel graphite material to meet the required material properties, it is essential to investigate the relationship among the process parameters of the matrix graphite powder preparation, the fabrication parameters of fuel element green compact and the heat treatments conditions and the material properties of fuel element. It was observed, during this development, that the pressing technique employed for the compaction fabrication prior to the two successive heat treatments (carbonization and final high temperature heat treatment) was of extreme importance in determining the material properties of the final compact product. In this work, the material behavior of the uni-axially pressed graphite matrix during the carbonization and final heat treatment are evaluated and summarized along the different directions, viz., perpendicular and parallel directions to pressing direction. In this work, the dimensional variations and variations in thermal expansion, thermal conductivity and Vickers hardness of the graphite matrix compact samples in the axial and radial directions prepared by uni-axial pressing are evaluated, and compared with those of samples prepared by cold isostatic pressing with the available data. From this work, the followings are observed. 1) Dimensional changes of matrix graphite green compacts during carbonization show that the difference in radial and axial variations shows a large anisotropic behavior in shrinkage. The radial variation is very small while the axial variation is large. During carbonization, the stresses caused by the force would be released in to the axial direction together with the phenolic resin vapor. 2) Dimensional variation of compact samples in perpendicular and parallel directions during carbonization shows a large difference in behavior when compact sample is prepared by uni-axial pressing. However, when compact sample is prepared by cold isostatic pressing, there is

Anisotropic Material Behavior of Uni-axially Compacted Graphite Matrix for HTGR Fuel Compact Fabrication

International Nuclear Information System (INIS)

Lee, Young-Woo; Yeo, Seunghwan; Yoon, Ji-Hae; Cho, Moon Sung

2016-01-01

In developing the fuel compact fabrication technology, and fuel graphite material to meet the required material properties, it is essential to investigate the relationship among the process parameters of the matrix graphite powder preparation, the fabrication parameters of fuel element green compact and the heat treatments conditions and the material properties of fuel element. It was observed, during this development, that the pressing technique employed for the compaction fabrication prior to the two successive heat treatments (carbonization and final high temperature heat treatment) was of extreme importance in determining the material properties of the final compact product. In this work, the material behavior of the uni-axially pressed graphite matrix during the carbonization and final heat treatment are evaluated and summarized along the different directions, viz., perpendicular and parallel directions to pressing direction. In this work, the dimensional variations and variations in thermal expansion, thermal conductivity and Vickers hardness of the graphite matrix compact samples in the axial and radial directions prepared by uni-axial pressing are evaluated, and compared with those of samples prepared by cold isostatic pressing with the available data. From this work, the followings are observed. 1) Dimensional changes of matrix graphite green compacts during carbonization show that the difference in radial and axial variations shows a large anisotropic behavior in shrinkage. The radial variation is very small while the axial variation is large. During carbonization, the stresses caused by the force would be released in to the axial direction together with the phenolic resin vapor. 2) Dimensional variation of compact samples in perpendicular and parallel directions during carbonization shows a large difference in behavior when compact sample is prepared by uni-axial pressing. However, when compact sample is prepared by cold isostatic pressing, there is

The Liberal Struggle for Press Freedom

DEFF Research Database (Denmark)

Mogensen, Kirsten

In this paper, the public debate following the re-ligion-motivated assassination of Dutch filmmaker Theo van Gogh in November 2004 is examined. The paper aims at describ-ing religious as well as secular positions in the Danish debate about freedom of speech and press in relation to religious issues....... Historically, the concept of press freedom was linked to a fight for religious freedom in London, as described by Siebert....

1979: The Campus Student Press in America.

Science.gov (United States)

Ingelhart, Louis E.

1979-01-01

Discusses a number of topics involving the campus press, including the independence of campus publications, censorship issues, the relationship between the student press and the college administrator, the financing of student newspapers, yearbook production and financing, probable future student publications trends, and the need for appropriate…

Jatropha press cake as organic fertilizer in lettuce cultivation

Directory of Open Access Journals (Sweden)

José R. Mantovani

Full Text Available ABSTRACT In biodiesel production, vegetable press cake is obtained as waste, and a suitable destination for jatropha press cake would be the use in agriculture as organic fertilizer. This study aimed to evaluate the effect of jatropha press cake on soil fertility attributes and on lettuce production and accumulation of nutrients in the shoots. The experiment was conducted in pots in a greenhouse, in a randomized block design with eight treatments and five replicates. The treatments consisted of doses of jatropha press cake equivalent to 0, 0.5, 1.0, 2.0, 4.0, 8.0, 16.0 and 32.0 t ha-1. Portions of 5.5 dm3 of soil received limestone, phosphate fertilizer and the doses of jatropha press cake, and remained incubated for 30 days. After incubation, soil samples were collected, each pot received one lettuce seedling and the experiment was carried out for 45 days. The organic fertilization with jatropha press cake increased the contents of nutrients in the soil, especially K+, but caused increment in soil acidity and electrical conductivity. The use of jatropha press cake as organic fertilizer decreased lettuce production and accumulation of nutrients in the shoots.

Cold-pressed and hot-pressed rapeseed oil: The effects of roasting and seed moisture on the antioxi- dant activity, canolol, and tocopherol level.

Science.gov (United States)

Siger, Aleksander; Józefiak, Marta; Górnaś, Paweł

2017-01-01

The paper looks at the levels of canolol, tocopherols and antioxidant activity in cold-pressed and hot-pressed rapeseed oils produced from seeds of various moisture levels (5%, 7.5%, and 10%). The paper also considers the effects of seed roasting on the levels of these compounds. The material used for the tests was rapeseed cv. Adrianna. The quality of the oils obtained is determined using peroxide and acid values. The levels of canolol and tocopherols are analyzed using HPLC. The DPPH radical-scavenging activity method for oil samples and phenolic extract from oils was used. It has been demonstrated that the oils produced from rapeseeds with a 5% moisture content, and   in particular from cold-pressed oils, were characterized by the lowest peroxide values. Cold-pressed oils produced from rapeseeds with a 5% moisture content were characterized by higher levels of tocopherols and plastochromanol-8. In the case of hot-pressed oils, the highest levels of tocopherols were found in oils pro- duced from seeds with a 7.5% moisture content, and the greatest amount of PC-8 (more than 4 mg/100 g) was found in oils produced from seeds with a 10% moisture content. Hot-pressed oils have been shown to have higher levels of these compounds than cold-pressed oils. Both roasting and hot pressing led to an increase in the amount of canolol in the oils investigated. When analysing the antioxidant activity of the oils and phenolic extracts it was shown that phenolic compounds are responsible for approx. 10% of total antioxidant activity. Various levels of biologically active compounds were shown to be present in the rapeseed oil obtained from raw materials of a varying moisture content. The type of pressing process (cold-pressing or hot-pressing) and whether the seeds have undergone roasting has also been shown to affect the resulting oil and the level of native antioxidants it contains.

Study of Servo Press with a Flywheel

Science.gov (United States)

Tso, Pei-Lum; Li, Cheng-Ho

The servo press with a flywheel is able to provide flexible motions with energy-saving merit, but its true potential has not been thoroughly studied and verified. In this paper, such the “hybrid-driven” servo press is focused on, and the stamping capacity and the energy distribution between the flywheel and the servomotor are investigated. The capacity is derived based on the principle of energy conservation, and a method of using a capacity percentage plane for evaluation is proposed. A case study is included to illustrate and interpret that the stamping capacity is highly dependent on the programmed punch motions, thus the capacity prediction is always necessary while applying this kind of servo press. The energy distribution is validated by blanking experiments, and the results indicate that the servomotor needs only to provide 15% to the flywheel torque, 12% of the total stamping energy. This validates that the servomotor power is significantly saved in comparison with conventional servo presses.

Distal clavicular osteolysis in adults: association with bench pressing intensity

International Nuclear Information System (INIS)

Nevalainen, Mika T.; Morrison, William B.; Zoga, Adam C.; Roedl, Johannes B.; Ciccotti, Michael G.

2016-01-01

To investigate the association between distal clavicular osteolysis (DCO) and bench pressing intensity. From a retrospective review of MRI shoulder reports of individuals between 20 and 40 years of age, 262 male patients with DCO and 227 age-matched male patients without DCO were selected. All patients had completed a bench pressing questionnaire. The patients' bench pressing frequency (times per week), duration (years of bench pressing), bench pressing weight (maximum bench pressing weight with one repetition = 1RM) and the ratio of bench pressing weight to body weight were compared between both groups using Chi-square and Mann-Whitney tests. The results showed that 56 % (146/262) of patients with DCO were high-intensity bench pressers (1RM more than 1.5 times the body weight) compared to 6 % (14/227) in patients without DCO. High-intensity bench pressing was a risk factor for DCO (OR = 19; 95 %CI = 11-35; p 1 x /week) and duration (>5 years) of bench pressing were risk factors. In bench pressers who suffered from DCO, the mean 1RM was 283 lbs (±SD 57) compared to 209 lbs (±SD 60) in bench pressers not affected by DCO (p < 0.001, Mann-Whitney). High-intensity, but not low-intensity bench pressing is a risk factor for DCO. (orig.)

Resident-performed Ex-PRESS shunt implantation versus trabeculectomy.

Science.gov (United States)

Seider, Michael I; Rofagha, Soraya; Lin, Shan C; Stamper, Robert L

2012-09-01

To compare outcomes between resident-performed trabeculectomy and Ex-PRESS shunt implantation. A consecutive cohort of 36 Ex-PRESS shunt implantations and 57 trabeculectomies (1 eye/patient) performed by resident surgeons in their third year of ophthalmic training at the University of California, San Francisco and at the San Francisco Veterans Administration Hospital, under the supervision of a single glaucoma fellowship-trained surgeon were included in this study. Eyes with PRESS shunt groups at all follow-up points. On average, the Ex-PRESS shunt group required significantly less ocular antihypertensive medication to control IOP at 3 months postoperative (P=0.01), but no difference was found at 6 months or 1 year (all, P≥0.28). A larger proportion of Ex-PRESS shunt patients had good IOP control without medication at 3 (P=0.057) and 6 months (P=0.076) postoperatively. No difference was found in the rates of sight-threatening complications between groups (all, P≥0.22). In the hands of ophthalmology residents in their third year of training, the trabeculectomy and Ex-PRESS shunt implantation procedures perform comparably in terms of postoperative IOP control, reduction in patient dependence on ocular antihypertensive medications, and risk of complication in our population.

WordPress 24-hour trainer

CERN Document Server

Plumley, George

2015-01-01

Create and expand feature-rich sites with no programming experience Ready to build, maintain, and expand your web site with WordPress but have no prior programming experience? WordPress 24-Hour Trainer, 3rd Edition is your book-and-video learning solution that walks you step-by-step through all the important features you will need to know. Lessons range from focused, practical everyday tasks to more advanced, creative features. Learn from an industry professional how to enter content, create pages, manage menus, utilize plug-ins, connect to social media, create membership and e-commerce site

Direct drive digital servo press with high parallel control

Science.gov (United States)

Murata, Chikara; Yabe, Jun; Endou, Junichi; Hasegawa, Kiyoshi

2013-12-01

Direct drive digital servo press has been developed as the university-industry joint research and development since 1998. On the basis of this result, 4-axes direct drive digital servo press has been developed and in the market on April of 2002. This servo press is composed of 1 slide supported by 4 ball screws and each axis has linearscale measuring the position of each axis with high accuracy less than μm order level. Each axis is controlled independently by servo motor and feedback system. This system can keep high level parallelism and high accuracy even with high eccentric load. Furthermore the 'full stroke full power' is obtained by using ball screws. Using these features, new various types of press forming and stamping have been obtained by development and production. The new stamping and forming methods are introduced and 'manufacturing' need strategy of press forming with high added value and also the future direction of press forming are also introduced.

Distal clavicular osteolysis in adults: association with bench pressing intensity

Energy Technology Data Exchange (ETDEWEB)

Nevalainen, Mika T.; Morrison, William B.; Zoga, Adam C.; Roedl, Johannes B. [Sidney Kimmel Medical College at Thomas Jefferson University, Division of Musculoskeletal Imaging and Interventions, Department of Radiology, Thomas Jefferson University Hospital, Philadelphia, PA (United States); Ciccotti, Michael G. [Sidney Kimmel Medical College at Thomas Jefferson University, Division of Sports Medicine, Department of Orthopedic Surgery, Thomas Jefferson University Hospital, Rothman Institute, Philadelphia, PA (United States)

2016-11-15

To investigate the association between distal clavicular osteolysis (DCO) and bench pressing intensity. From a retrospective review of MRI shoulder reports of individuals between 20 and 40 years of age, 262 male patients with DCO and 227 age-matched male patients without DCO were selected. All patients had completed a bench pressing questionnaire. The patients' bench pressing frequency (times per week), duration (years of bench pressing), bench pressing weight (maximum bench pressing weight with one repetition = 1RM) and the ratio of bench pressing weight to body weight were compared between both groups using Chi-square and Mann-Whitney tests. The results showed that 56 % (146/262) of patients with DCO were high-intensity bench pressers (1RM more than 1.5 times the body weight) compared to 6 % (14/227) in patients without DCO. High-intensity bench pressing was a risk factor for DCO (OR = 19; 95 %CI = 11-35; p < 0.001). Low-intensity bench pressing (1RM less than 1.5 times the body weight) was not a risk factor for DCO (OR = 0.6; 95 % CI = 0.4-0.8). High frequency (>1 x /week) and duration (>5 years) of bench pressing were risk factors. In bench pressers who suffered from DCO, the mean 1RM was 283 lbs (±SD 57) compared to 209 lbs (±SD 60) in bench pressers not affected by DCO (p < 0.001, Mann-Whitney). High-intensity, but not low-intensity bench pressing is a risk factor for DCO. (orig.)

Quantitative description of microstructure defects in hexagonal boron nitrides using X-ray diffraction analysis

International Nuclear Information System (INIS)

Schimpf, C.; Motylenko, M.; Rafaja, D.

2013-01-01

A routine for simultaneous quantification of turbostratic disorder, amount of puckering and the dislocation and stacking fault density in hexagonal materials was proposed and tested on boron nitride powder samples that were synthesised using different methods. The routine allows the individual microstructure defects to be recognised according to their effect on the anisotropy of the X-ray diffraction line broadening. For quantification of the microstructure defects, the total line broadening is regarded as a linear combination of the contributions from the particular defects. The total line broadening is obtained from the line profile fitting. As testing material, graphitic boron nitride (h-BN) was employed in the form of hot-isostatically pressed h-BN, pyrolytic h-BN or a h-BN, which was chemically vapour deposited at a low temperature. The kind of the dominant microstructure defects determined from the broadening of the X-ray diffraction lines was verified by high resolution transmission electron microscopy. Their amount was attempted to be verified by alternative methods. - Highlights: • Reliable method for quantification of microstructure defects in BN was suggested. • The method is based on the analysis of anisotropic XRD line broadening. • This XRD line broadening is unique and characteristic of the respective defect. • Thus, the quantification of coexistent microstructure defects is possible. • The method was tested on hexagonal BN, which was produced by different techniques

Communicators take nine Virginia Press Women awards

OpenAIRE

Owczarski, Mark

2008-01-01

Three Virginia Tech communicators have won Virginia Press Women awards. The winners - Susan Trulove, research division communications manager; Clara Cox, university publications director; and Heather Riley Chadwick, College of Architecture and Urban Studies communication manager - were announced at the Virginia Press Women Annual Spring Conference in Staunton, Va.

CSR-communication in the Business Press

DEFF Research Database (Denmark)

Morsing, Mette; Langer, Roy

on a broadly encompassing and ambiguous definition of CSR. Our empirical data shows how the business press in its discourse on CSR provides no clarity on the definition of CSR in terms of a coherent motive, a dominant stakeholder or a consistent issue, but rather maintains ambiguity and imprecision about......In this paper we analyze the construction of corporate social responsibility in the business press as an act of strategic ambiguity. While corporate social responsibility (CSR) generally evokes positive associations in public opinion, this paper demonstrates that these associations are based...... is systematically maintained in the business press. We refer to this process as strategic ambiguity. The paper discusses the potential value and limitations of framing CSR in a state of strategic ambiguity in the context of the concurrent rethinking of the role of business in modern welfare societies....

Tilting of Lake Pielinen, eastern Finland – an example of extreme transgressions and regressions caused by differential post-glacial isostatic uplift

Directory of Open Access Journals (Sweden)

Heikki Seppä

2012-08-01

Full Text Available Tilting of large lakes due to differential isostatic uplift in the glaciated regions of the Northern Hemisphere is a well-documented process. With the help of accurate digital elevation models and spatial GIS analysis techniques, the resulting hydro­logical changes, including shifts in the outlets and changes in the size and configuration of lakes, can now be mapped and calculated more precisely than before. As a case study to highlight the magnitude of such changes in Fennoscandia, we investigated and reinterpreted the Holocene palaeogeography and palaeohydrology of Lake Pielinen in eastern Finland. This lake is currently 99 km long and located parallel to the direction of land uplift, being thus particularly sensitive to the impacts of tilting. Our results show that the lake was formed at the end of the regional deglaciation, following drainage of a local ice-dammed lake. In its initial stage until 10 200 cal yr BP, the outlet of the newly-formed lake was located in its northwestern end, but the tilting led to a major water level transgression in the basin, eventually causing formation of a new outlet over the southeastern threshold. The lake area was 143 km long and its area was 1998 km2 at the time of formation of the southeastern outlet at 10 200 cal yr BP. The lake level has been regressive throughout the basin during the last 10 200 years. This regression will continue for approximately another 10 000 years until all the glacial isostatic adjustment has occurred, after which Lake Pielinen will be only 89 km long and 565 km2 in area.

Damage on 316LN stainless steel transformed by powder metallurgy

International Nuclear Information System (INIS)

Couturier, R.; Burlet, H.

1998-01-01

This study deals with the 316 LN stainless steel elaboration by powder metallurgy. This method allows the realization of structures in austenitic steel less affected by the thermal aging than the cast austenitic-ferritic components. The components are performed by the method of HIP (Hot Isostatic Pressing). Mechanical tests are provided to control mechanical properties

ASEA reduces nuclear waste in Sweden

International Nuclear Information System (INIS)

Anon.

1977-01-01

ASEA, the worldwide manufacturer of electrical and mechanical equipment with headquarters in Vasteras, Sweden, is working on the development of a method using hot isostatic pressing for the safe containment and storage of nuclear waste. This development work is being carried out at the company's High-Pressure Laboratory at Robertsfors, in the north of Sweden

bbPress complete

CERN Document Server

Wynne, Rhys

2013-01-01

A concise guide, written in an easy-to-follow format.This book is aimed at ambitious website or blog owners looking to add a forum to their site quickly and easily. Basic experience in WordPress and with managing a website is expected. Knowledge of HTML and PHP will be a bonus, though it isn't necessary.

Legal Protection To The Infotainment Of Press Development In Indonesia

Directory of Open Access Journals (Sweden)

Anwar Fuadi

2015-08-01

Full Text Available Abstract In the socio-political life the press has become an integral part in democratic life. The press has become one of the means for citizens to bring their thoughts and opinions. Nowadays there is a tendency to increase the quantity of press publications sharp but not accompanied by a statement of the quality of journalism. The objective of this research is to understand the essence of the infotainment liability as a mass media in order to construct a freedom of the press principle which has legitimacy within the legal system of the press in Indonesia. The type of research used in this paper is normative research or also known as doctrinal research by reviewing the legal protection to the infotainment as a mass media in Indonesia. The outcomes of the research indicate that the role of infotainment in the legal system of the press in Indonesia refers to the legal construction of institutional and infotainment organizers itself. Legal liability of Infotainment essentially can be seen from the press obligations stipulated in the Law No. 40 of 1999 regarding the Press Law No. 32 of 2002 regarding Broadcasting as well as the Journalists Code of Ethics which support freedom of the press and expression.

Concept Design of Movable Beam of Hydraulic Press

Directory of Open Access Journals (Sweden)

Li Yancong

2017-01-01

Full Text Available The hydraulic press movable beam is one of the key components of the hydraulic press; its design quality impacts the accuracy of the workpiece that the press suppressed. In this paper, first, with maximum deflection and material strength as constraints, mechanical model of the movable beam is established; next, the concept design model of the moveable beam structure is established; the relationship among the force of the side cylinder, the thickness of the inclined plate, outer plate is established also. Taking movable beam of the 100MN type THP10-10000 isothermal forging hydraulic press as an example, the conceptual design result is given. This concept design method mentoned in the paper has general meaning and can apply to other similar product design.

Fabrication and properties of hot pressed bismuth tungstate

International Nuclear Information System (INIS)

Streicher, W.L.

1978-01-01

Bi 2 WO 6 is a synthetic polar material that is a possible candidate for energy conversion and detection systems. Previous research on this material has been concerned with crystal growth and sintering characteristics of polycrystalline compacts. This study involves itself with the fabrication of polycrystalline compacts by hot pressing techniques. Densities approaching theoretical crystal density were achieved by hot pressing at 850 0 C for one hour with pressures exceeding 35 MPa. Before hot pressing, the sintering range was determined by high temperature dilatometry of unfired Bi 2 WO 6 ceramics. Hot pressed discs were characterized by scanning electron microscopy, differential scanning calorimetry, and x-ray diffraction. Electrical properties were determined by dc resistivity, capacitance, and conductance measurements, ac poling, dc poling, and current-voltage measurements

Student Press in American Archives, Fall/Winter 1973-74.

Science.gov (United States)

National Council of Coll. Publications Advisers.

This issue of the "Student Press in America Archives List" contains 100 entries on current issues and information, as well as cases involving student press editors, advisers, student media, and the generic subject of the campus press, emphasizing censorship practices and principles. Information concerning how and where to obtain documents of…

Microstructural evolution and some mechanical properties of nanosized yttrium oxide dispersion strengthened 13Cr steel

International Nuclear Information System (INIS)

Nguyen, Van Tich; Doan, Dinh Phuong; Tran, Tran BaoTrung; Luong, Van Duong; Nguyen, Van An; Phan, Anh Tu

2010-01-01

Oxide dispersion strengthened (ODS) steels, manufactured by a mechanical alloying method, during the past few years, appear to be promising candidates for structural applications in nuclear power plants. The purpose of this work is to elaborate the manufacturing processes of ODS 13Cr steel with the addition of 1.0 wt% yttrium oxide through the powder metallurgy route using the high energy ball mill. Microstructural analysis by scanning electron microscopy (SEM), x-ray diffraction (XRD) and hardness testing have been used to optimize the technological parameters of milling, hot isostatic pressing and heat-treatment processes. The steel hardness increases with decreasing particle size of 13Cr ODS steel. The best hardness was obtained from more than 70 h of milling in the two tanks planetary ball mill or 30 h of milling in the one tank planetary ball mill and hot isostatic pressing at 1150 °C . The particle size of the steel is less than 100 nm, and the density and hardness are about 7.3 g cm −3 and 490 HB, respectively

Laser properties of Fe2+:ZnSe fabricated by solid-state diffusion bonding

Science.gov (United States)

Balabanov, S. S.; Firsov, K. N.; Gavrishchuk, E. M.; Ikonnikov, V. B.; Kazantsev, S. Yu; Kononov, I. G.; Kotereva, T. V.; Savin, D. V.; Timofeeva, N. A.

2018-04-01

The characteristics of an Fe2+:ZnSe laser at room temperature and its active elements with undoped faces were studied. Polycrystalline elements with one or two diffusion-doped internal layers were obtained by the solid-state diffusion bonding technique applied to chemical vapor deposition grown ZnSe plates preliminary doped with Fe2+ ions in the process of hot isostatic pressing. A non-chain electric-discharge HF laser was used to pump the crystals. It was demonstrated that increasing the number of doped layers allows increasing the maximum diameter of the pump radiation spot and the pump energy without the appearance of transversal parasitic oscillation. For the two-layer-doped active element with a diameter of 20 mm an output energy of 480 mJ was achieved with 37% total efficiency with respect to the absorbed energy. The obtained results demonstrate the potential of the developed technology for fabrication of active elements by the solid-state diffusion bonding technique combined with the hot isostatic pressing treatment for efficient IR lasers based on chalcogenides doped with transition metal ions.

Porous titanium obtained by a new powder metallurgy technique: Preliminary results of human osteoblast adhesion on surface polished substrates.

Science.gov (United States)

Biasotto, M; Ricceri, R; Scuor, N; Schmid, C; Sandrucci, M A; Di Lenarda, R; Matteazzi, P

2003-01-01

This study concerns a novel powder metallurgy method for producing porous titanium (pTi) exhibiting high mechanical properties. The preparation procedure consisted of the following stages: first, the preparation of Ti and titanium hydride (TiH2) powder mixtures and their consolidation with a cold isostatic press, followed by a sintering of the green bodies performed with hot isostatic press (HIP) equipment. Thermal decomposition in controlled environment of the TiH2 phase results in the foam structure. The resulting porosity percolates with a volume fraction of approximately 20%. The final material exhibits interesting mechanical properties, comparable to those of full density titanium (between grade 2 and grade 3), with the advantage of a minor density. The samples produced were tested to verify their biological response by studying the effectiveness of osteoblast adhesion and growth. In this preliminary study, osteoblastic cell morphology was investigated and compared to that observed on fully dense commercially pure titanium (Ti-cp) (ASTM, grade 3). The preliminary results were promising regarding cellular adhesion and spreading. (Journal of Applied Biomaterials & Biomechanics 2003; 1: 172-7).

Evaluation of tensile strength and fracture toughness of yttria-stabilized zirconia polycrystals with fracture surface analysis

International Nuclear Information System (INIS)

Oishi, Manabu; Matsuda, Yukihisa; Noguchi, Kenichi; Masaki, Takaki

1995-01-01

The tensile strength of yttria-stabilized tetragonal zirconia polycrystals (Y-TZPs) was measured and the fracture surfaces were analyzed with the scanning electron microscope and X-ray microanalyzer. The fracture origins of the pressureless-sintered samples were voids or inclusions such as Al 2 O 3 , Al 2 O 3 with SiO 2 , and cubic-ZrO 2 , while the fracture origins of the hot isostatically pressed samples were inclusions; no voids were detected at fracture origins. The higher strengths of the hot isostatically pressed samples versus those of the pressureless-sintered samples were consistent with the change in fracture origins. The fracture toughness of the samples calculate from the tensile strength and analysis of the fracture origins was 3.4 to 3.7 MPa ·√m. These values are lower than those measured with the SEPB method. These discrepancies might be caused by the difference in the state of the fracture origin and its neighborhood, such as the size of the fracture origin and interaction between two surfaces in the precrack

Engaging and Supporting a University Press Scholarly Community

Directory of Open Access Journals (Sweden)

Megan Taylor

2018-03-01

Full Text Available In this paper we explore how the development of The University of Huddersfield Press, a publisher of open access scholarly journals and monographs, has enabled the sharing of research with a wider online audience. We situate the development of the Press within a wider research environment and growing community of New University Presses (NUPs where there is an increasing demand for demonstrating research impact, which drives the need for improved analysis and reporting of impact data, a task that often falls within the remit of library and academic support services. We detail the benefits of the University Press Manager role in terms of ensuring professional service that delivers consistency and sustainability. We go on to outline the experiences of engaging with different online spaces and detail the extensive support for student authors. We argue that in order for the Press to support building a strong and engaged scholarly community and provide new spaces for emerging research, continued investment in both platform development and infrastructure is required.

Hot pressing of B{sub 4}C/SiC composites

Energy Technology Data Exchange (ETDEWEB)

Sahin, F.C.; Turhan, E.; Yesilcubuk, S.A.; Addemir, O. [Ystanbul Technical University, Faculty of Chemistry and Metallurgy, Materials and Metallurgical Engineering Dept., Maslak-Ystanbul (Turkey)

2005-07-01

B{sub 4}C/SiC ceramic composites containing 10-20-30 vol % SiC were prepared by hot pressing method. The effect of SiC addition and hot pressing temperature on sintering behaviour and mechanical properties of hot pressed composites were investigated. Microstructures of hot pressed samples were examined by SEM technique. Three different temperatures (2100 deg. C, 2200 deg. C and 2250 deg. C) were used to optimize hot pressing temperature applying 100 MPa pressure under argon atmosphere during the sintering procedure. The highest relative density of 98.44 % was obtained by hot pressing at 2250 deg. C. However, bending strengths of B{sub 4}C/SiC composite samples were lower than monolithic B{sub 4}C in all experimental conditions. (authors)

WordPress 3 For Business Bloggers

CERN Document Server

Thewlis, Paul

2011-01-01

This is a practical, hands-on book based around a fictitious case study blog, which you will build on a development server using WordPress. The case study grows chapter by chapter, from installing your local development server, right up to the finished blog. This book is for anybody running or starting a business blog using WordPress, whether you plan to use your blog for PR and marketing, or want to profit directly from blogging.

FREEDOM OF PRESS AND JURY TRIAL IN ISTRIA 1848/1849

Directory of Open Access Journals (Sweden)

Dunja Pastović

2015-01-01

Full Text Available In Istria, as a part of the Austrian legal system, jury trial was initially introduced in the revolutionary year of 1848 only for press offenses, in the framework of aspirations for freedom of thought and expression through the press, which represented the most appropriate medium for the dissemination of new ideas and mobilization of the political masses. Trial by jury was supposed to secure impartial and objective trials, which could not be expected of professional judges due to insufficient guarantees of their impartiality. This paper examines the press-related orders and laws passed during 1848 and 1849 which regulated the freedom of press and jury jurisdiction. On the basis of an analysis of the legislative framework, jurisprudence, and the Istrian press during the examined time period, the author has decided that the introduction of the freedom of the press and jury trials for press offenses in 1848/1849 on the territory of Istria didn’t have a large practical significance.

"Mended or ended?" Football injuries and the British and American medical press, 1870-1910.

Science.gov (United States)

Park, R J

2001-01-01

'Playing Hurt/Playing Tough', a dominant ideology in today's football (soccer, rugby, American 'gridiron'), is by no means new. Many books, monographs, and articles have examined the historical development of these games, but the attention given to them in the medical press during the late 1800s/early 1900s has been overlooked. The Lancet, Journal of the American Medical Association, and other turn-of-the-century medical publications regularly included accounts and descriptions of injuries and deaths. More telling were the many editorials in which physicians in both Britain and the United States expressed enthusiasm while also lamenting the games' physical and morale effects upon players, asking whether 'football' should be mended or ended.

Comparison of Myoelectric Activity of a Selection of Upper Extremity Muscles while Doing Bench Press in Two Training Methods of TRX and Barbell Bench Press

Directory of Open Access Journals (Sweden)

Ahmad Reza Zibaei

2016-12-01

Conclusion: Considering these results it can be maintained that TRX bench press resistance training can be an alternative and effective practice for barbell bench press because, given the results, it can be appreciated that TRX bench press, dips low in the trunk, can lead to muscle activity close to the level of muscle activity during the barbell bench press drill.

Modelling of powder die compaction for press cycle optimization

Directory of Open Access Journals (Sweden)

Bayle Jean-Philippe

2016-01-01

Full Text Available A new electromechanical press for fuel pellet manufacturing was built last year in partnership between CEA-Marcoule and ChampalleAlcen. This press was developed to shape pellets in a hot cell via remote handling. It has been qualified to show its robustness and to optimize the compaction cycle, thus obtaining a better sintered pellet profile and limiting damage. We will show you how 400 annular pellets have been produced with good geometry's parameters, based on press settings management. These results are according to a good phenomenological pressing knowledge with Finite Element Modeling calculation. Therefore, during die pressing, a modification in the punch displacement sequence induces fluctuation in the axial distribution of frictional forces. The green pellet stress and density gradients are based on these frictional forces between powder and tool, and between grains in the powder, influencing the shape of the pellet after sintering. The pellet shape and diameter tolerances must be minimized to avoid the need for grinding operations. To find the best parameters for the press settings, which enable optimization, FEM calculations were used and different compaction models compared to give the best calculation/physical trial comparisons. These simulations were then used to predict the impact of different parameters when there is a change in the type of powder and the pellet size, or when the behavior of the press changes during the compaction time. In 2016, it is planned to set up the press in a glove box for UO2 manufacturing qualification based on our simulation methodology, before actual hot cell trials in the future.

Mannes of Forging and Perspectives of Knuckle Joint Presses Modernization

Directory of Open Access Journals (Sweden)

A. A. Antsifirov

2014-01-01

Full Text Available The article raises an issue to enhance technological forging capabilities on the known knuckle joint presses. It provides an illustrated overview of main design types of presses with crank-knuckle, toggle-knuckle, and knuckle joint mechanisms. The article also shows the advantages of the modernization way and improvement just of the active press equipment in terms of quality-to-price ratio, for example, as compared to the similar new foreign press equipment.It gives an overview of features, which provide forging processes owing to kinetic energy accumulated with the moving parts of the known designs of the knuckle joint presses depending on the drive actuating mechanism. Focused attention is drawn to forging on the knuckle joint presses for a time of contact with a work piece to be comparable with the duration of the work piece deformation process on hydraulic forging hammers. This allows us to forge thin-wall products with process automation compared to the forging hammers.Analysis of accumulating processes of kinetic energy by the moving parts of the knuckle joint presses has shown that presses driven by hydraulic cylinders or two screw hydraulic cylinder are the most optimal for technological operations as evidenced by references to domestic and foreign invention certificates and patents. The article presents disadvantages of forging on presses with hydraulic or pneumatic drive. It is a dependence of the deformation force, caused, mainly, by a force of the drive cylinder. The article gives linear movement rate quantities of press moving members depending on the drives of the actuating mechanism. Based on the above analysis of the features to manufacture work pieces on the knuckle joint presses, the article gives the rationale for the relevance of forging in a short period of time, provided that the moving parts of the press accumulate the required kinetic energy. This can be achieved only through modernization and improvement of forging

The effect of signal leakage and glacial isostatic rebound on GRACE-derived ice mass changes in Iceland

DEFF Research Database (Denmark)

Sørensen, Louise Sandberg; Jarosch, Alexander H.; Adalgeirsdottir, Gudfinna

2017-01-01

Monthly gravity field models from the GRACE satellite mission are widely used to determine ice mass changes of large ice sheets as well as smaller glaciers and ice caps. Here, we investigate in detail the ice mass changes of the Icelandic ice caps as derived from GRACE data. The small size...... of the Icelandic ice caps, their location close to other rapidly changing ice covered areas and the low viscosity of the mantle below Iceland make this especially challenging. The mass balance of the ice caps is well constrained by field mass balance measurements, making this area ideal for such investigations. We...... the Little Ice Age (∼ 1890 AD). To minimize the signal that leaks towards Iceland from Greenland, we employ an independent mass change estimate of the Greenland Ice Sheet derived from satellite laser altimetry. We also estimate the effect of post Little Ice Age glacial isostatic adjustment, from knowledge...

Study beryllium microplastic deformation

International Nuclear Information System (INIS)

Papirov, I.I.; Ivantsov, V.I.; Nikolaenko, A.A.; Shokurov, V.S.; Tuzov, Yu.V.

2015-01-01

Microplastic flow characteristics systematically studied for different varieties beryllium. In isostatically pressed beryllium it decreased with increasing particle size of the powder, increasing temperature and increasing the pressing metal purity. High initial values of the limit microelasticity and microflow in some cases are due a high level of internal stresses of thermal origin and over time it can relax slowly. During long-term storage of beryllium materials with high initial resistance values microplastic deformation microflow limit and microflow stress markedly reduced, due mainly to the relaxation of thermal microstrain

Higher-performance beryllium materials for aerospace and defense applications

International Nuclear Information System (INIS)

Parsonage, T.B.

1991-01-01

A new plant has been tooled for the production of near-net-shape blanks for Be structural components, using both HIP and cold isostatic pressing to consolidate Be powders. Attention is given to blanks for integrally honeycomb-reinforced lightweight mirrors. HIPed materials' ultimate tensile strength is superior to that of vacuum hot-pressed material, due to the finer grain sizes obtainable via P/M powder consolidation, lower consolidation temperatures, and shorter processing cycle. The use of spherical Be powders allows higher packing density than for impact-ground powders, resulting in reduced shrinkage upon consolidation

Movement Features Which Describe the Flat Bench Press

Directory of Open Access Journals (Sweden)

Król Henryk

2017-06-01

Full Text Available Introduction. In sport technique studies, motion features can be useful as they have a certain defined measure [1]. In this work, we examined the following three features: the structure of the movement (all the characteristics of the movement, the fluency of the movement, and the rhythm of the movement. The aim of the study was to determine the usefulness of the selected movement features in the evaluation of the flat bench press. The protocol of the study included a flat bench press with free weights and a “touch-and-go” technique. Material and methods. The study involved twenty healthy men; however, only two were selected for analysis. The first subject was a 25-year-old powerlifter (body mass = 95 kg; body height = 182 cm; 1-RM in flat bench press = 145 kg. The second one was a 25-year-old bodybuilder (body mass = 77 kg; body height = 175 cm; 1-RM in flat bench press = 100 kg. The subjects performed consecutive sets of a single repetition of flat bench pressing with an increasing load (70, 80, 90, and 100% 1-RM, with the anticipated maximum weight, until the completion of one repetition maximum. Multidimensional movement analysis was made with the measuring system Smart-E (BTS, Italy, which consisted of six infrared cameras (120 Hz and a wireless module to measure muscle bioelectric activity (Pocket EMG. Results. It was demonstrated that the internal structure of the bench press performed by the bodybuilder and the powerlifter was different. As the time-history of barbell kinematics (the acceleration-time curve showed, with increased loading of the barbell, the rhythm of the flat bench press changed, and the fluidity of the movement worsened.

Myths About Press Freedom

Directory of Open Access Journals (Sweden)

Kaarle Nordenstreng

2007-06-01

Full Text Available This article intends to rectify three popular beliefs related to press freedom: (1 that the idea of a free marketplace of ideas with a self-righting truth belongs to original liberalism, (2 that UNESCO’s primary mission is to promote freedom of information, and (3 that the Universal Declaration of Human Rights provides legal safeguards for the media. These beliefs are shown, on the basis of the legacy of liberalism and documents of the international community, to be misleading myths. Instead of accurate readings of the idea of freedom, they serve as ideological positions which are harmful to democracy. The Millennium Declaration provides further proof that the international community has a much more balanced view of freedom of information than that typically held by media professionals. Therefore it is important to liberate the concept of press freedom from its ideological baggage.

Microplasticity in hot-pressed beryllium

International Nuclear Information System (INIS)

Plane, D.C.; Bonfield, W.

1977-01-01

Closed hysteresis loops measured in the microstrain region of hot pressed, commercially pure, polycrystalline beryllium are correlated with a dislocation - impurity atom, energy dissipating mechanism. (author)

News from the Library: PressDisplay on mobile devices!

CERN Multimedia

CERN Library

2013-01-01

You are probably already using PressDisplay to read newspapers online, but for those of you who are not yet aware of this service, PressDisplay is an online portal where you can browse and read online articles from more than 1,900 newspapers from 95 countries, as soon as they are published.   Whether you are an experienced user or a beginner, we have good news concerning PressDisplay: our license now permits you to download complete newspaper issues to your mobile devices and read them offline wherever you like. To do that, you have to use the mobile app PressReader. Instructions on how to install the PressReader app are available here: For Ipad For Android smartphone For Android tablet For Windows 8 devices For BlackBerry Playbook For Android eReader Your feedback is welcome! Please contact us by e-mail.

Pressing technology for large bottoms

International Nuclear Information System (INIS)

Jilek, L.

1986-01-01

The technology has been selected of a circular plate bent into the shape of a trough, for pressing bottoms of pressure vessels from a circular plate of large diameter. The initial sheet is first bent in the middle by heating with the edges remaining straight. These are then welded longitudinally by electroslag welding and the circular shape is flame cut. The result will be a plate with a straight surface in the middle with raised edges which may be pressed into the desired shape. In this manner it is also possible to press pressure vessel bottoms with tube couplings from plates which are thickened in the middle and drilled; additional welding is then eliminated. Deformation from heat treatment may be avoided by the use of a fixture in the shape of a ring with a groove into which is fixed the edge of the bottom. During hardening of the bottom it will be necessary to care for the withdrawal of vapours and gases which would hamper uniform cooling. Bottom hardening with the grill and the cupola downwards has been proven. Deformation which occurs during treatment may to a certain extent be removed by calibration which cannot, however, be made without special fixtures and instruments. (J.B.)

Simulation Model of Automated Peat Briquetting Press Drive

Directory of Open Access Journals (Sweden)

A. A. Marozka

2012-01-01

Full Text Available The paper presents the developed fully functional simulation model of an automated peat briquetting press drive. The given model makes it possible to reduce financial and time costs while developing, designing and operating a double-stamp peat briquetting press drive.

Predictor of regulation of uranium dioxide powder pressing process

International Nuclear Information System (INIS)

Motta, Eduardo Souza; Araujo, Victor Hugo Leal de; Bernardelli, Sergio Henrique

2007-01-01

One of the most important steps of the uranium dioxide pellets fabrication used in the nuclear fuel elements is the green pellets pressing. The target density of the pellets after the sintering process determines the density of the green pellet. To meet the same sintered target density the green density may vary according to the powder characteristics. These variations implies in changing the regulation of the press for different powder's patches. The regulation done empirically imply in productivity loss and necessity of reprocessing the pellets pressed during the press regulation and also depends on the operator experience. At this work, was developed an artificial neural network feed forward back propagation to predict the press regulation, depending on the powder characteristics and the green pellet's target density. The results obtained at INB - Industrias Nucleares do Brasil S. A. during the fabrication of the fifth recharge of Angra II nuclear power plant are presented. (author)

Type synthesis for 4-DOF parallel press mechanism using GF set theory

Science.gov (United States)

He, Jun; Gao, Feng; Meng, Xiangdun; Guo, Weizhong

2015-07-01

Parallel mechanisms is used in the large capacity servo press to avoid the over-constraint of the traditional redundant actuation. Currently, the researches mainly focus on the performance analysis for some specific parallel press mechanisms. However, the type synthesis and evaluation of parallel press mechanisms is seldom studied, especially for the four degrees of freedom(DOF) press mechanisms. The type synthesis of 4-DOF parallel press mechanisms is carried out based on the generalized function(GF) set theory. Five design criteria of 4-DOF parallel press mechanisms are firstly proposed. The general procedure of type synthesis of parallel press mechanisms is obtained, which includes number synthesis, symmetrical synthesis of constraint GF sets, decomposition of motion GF sets and design of limbs. Nine combinations of constraint GF sets of 4-DOF parallel press mechanisms, ten combinations of GF sets of active limbs, and eleven combinations of GF sets of passive limbs are synthesized. Thirty-eight kinds of press mechanisms are presented and then different structures of kinematic limbs are designed. Finally, the geometrical constraint complexity( GCC), kinematic pair complexity( KPC), and type complexity( TC) are proposed to evaluate the press types and the optimal press type is achieved. The general methodologies of type synthesis and evaluation for parallel press mechanism are suggested.

Comparative waste forms study

International Nuclear Information System (INIS)

Wald, J.W.; Lokken, R.O.; Shade, J.W.; Rusin, J.M.

1980-12-01

A number of alternative process and waste form options exist for the immobilization of nuclear wastes. Although data exists on the characterization of these alternative waste forms, a straightforward comparison of product properties is difficult, due to the lack of standardized testing procedures. The characterization study described in this report involved the application of the same volatility, mechanical strength and leach tests to ten alternative waste forms, to assess product durability. Bulk property, phase analysis and microstructural examination of the simulated products, whose waste loading varied from 5% to 100% was also conducted. The specific waste forms investigated were as follows: Cold Pressed and Sintered PW-9 Calcine; Hot Pressed PW-9 Calcine; Hot Isostatic Pressed PW-9 Calcine; Cold Pressed and Sintered SPC-5B Supercalcine; Hot Isostatic pressed SPC-5B Supercalcine; Sintered PW-9 and 50% Glass Frit; Glass 76-68; Celsian Glass Ceramic; Type II Portland Cement and 10% PW-9 Calcine; and Type II Portland Cement and 10% SPC-5B Supercalcine. Bulk property data were used to calculate and compare the relative quantities of waste form volume produced at a spent fuel processing rate of 5 metric ton uranium/day. This quantity ranged from 3173 L/day (5280 Kg/day) for 10% SPC-5B supercalcine in cement to 83 L/day (294 Kg/day) for 100% calcine. Mechanical strength, volatility, and leach resistance tests provide data related to waste form durability. Glass, glass-ceramic and supercalcine ranked high in waste form durability where as the 100% PW-9 calcine ranked low. All other materials ranked between these two groupings

The regulation of press freedoms (1863-1867

Directory of Open Access Journals (Sweden)

Laurence Coudart

2015-10-01

Full Text Available The main objective of this essay is to analyze the legislation affecting the press during the French Intervention and the Second Mexican Empire and establish their regulatory effects. These regulations are frequently ignored by the historiography. The article is limited to the origins, innovations, mechanisms and evolution of printing regulations during this period. As a whole, this allows the reader to observe the restrictive conception of press freedom held by the Mexican political class and their willingness, during the second half of the 19th Century, to turn to prohibitive, repressive, authoritarian and centralist legislation. The article also reveals the extent to which Imperial legislation and its logic of censorship were neither unprecedented nor sudden foreign impositions but instead the expressions of a long-lasting desire for government control over the press.

Results and problems in the development of machines employed in pressing technology

Energy Technology Data Exchange (ETDEWEB)

Dietrich, P; Hinne, H; Linke, L; Nerger, R

1980-08-01

Features specifications and technical improvements of nine GDR made briquetting presses from the Zemag Zeitz company. Briquetting presses have been produced by the company for more than 100 years, the present capacity of the machines ranges from 5.1 t/h to 20.4 t/h of nominal briquet production. Development trends are directed toward larger presses. The prototype PSA 400, based on the design of the four channel press PSA 300, will be tested in industrial operation during 1980/81. Various technical details on the general briquetting press design are enumerated, including experiences gained with steam or electric power operated presses, regulation of the pressing speed with a patented switch gear system, maintenance of crank gear bearings, greasing of steam driven presses, investigation of crack damages to the machine block, further measures for reducing wear of the pressing channel and mechanized welding methods for the channel overhaul. (In German)

Science coverage and the press

International Nuclear Information System (INIS)

Hawkes, N.

1992-01-01

The writer, a journalist, summarizes the discussion of the Chilton Seminar, February 1992, and discusses the problems of bridging the incomprehension gap between scientists and lay readers of the press. (Author)

Design and testing of a solar photovoltaic operated multi-seeds oil press

Energy Technology Data Exchange (ETDEWEB)

Mpagalile, J.J. [Department of Food Science and Technology, Sokoine University of Agriculture, P.O. Box 3006, Morogoro (Tanzania); Hanna, M.A.; Weber, R. [Industrial Agricultural Products Center, University of Nebraska, 209 L.W. Chase Hall, Lincoln, NE 68583-0730 (United States)

2006-10-15

Oil expression tests were conducted to evaluate the performance of a novel oil expeller designed and fabricated to operate on a 200W solar photovoltaic (PV) power system as a sole power source. The oil press was designed to press oilseeds meal with intermediate moisture content of 12+/-1% (w.b.) and 0.5-2mm particle sizes. Freshly grated coconuts and ground peanuts were used to determine the oil expression efficiency of the press. The oilseed samples were pressed for 12min with a maximum pressure of 3.0MPa being reached at 6min of pressing for peanuts and 8min of pressing for coconuts. The pressure was then held for the rest of the pressing time. The press attained an average oil expression efficiency of 73% for coconuts and 70% for peanuts. The force-vs.-deformation studies indicated that peanut press meal was compacted at a higher rate as compared to coconuts. The observation on the energy consumption indicated that there was a significant increase (P<0.05) in the specific energy requirement for both coconuts and peanuts after 6min of pressing, which resulted from the solidification of the press cake. An average specific energy of 36.55 and 20.35Wh/kg was recorded for peanuts and coconuts, respectively, after 12min of pressing. (author)

A superconducting solenoid and press for permanent magnet fabrication

International Nuclear Information System (INIS)

Mulcahy, T. M.; Hull, J. R.

2002-01-01

For the first time, a superconducting solenoid (SCM) was used to increase the remnant magnetization of sintered NdFeB permanent magnets (PMs). In particular, improved magnetic alignment of commercial-grade PM powder was achieved, as it was axial die pressed into 12.7-mm diameter cylindrical compacts in the 76.2-mm warm bore of a 9-T SCM. The press used to compact the powder is unique and was specifically designed for use with the SCM. Although the press was operated in the batch mode for this proof of concept study, its design is intended to enable automated production. In operation, a simple die and punch set made of nonmagnetic materials was filled with powder and loaded into a nonmagnetic press tube. The cantilevered press tube was inserted horizontally, on a carrier manually advanced along a track, into the SCM. The robustness of the mechanical components and the SCM, in its liquid helium dewar, were specifically designed to allow for insertion and extraction of the magnetic powder and compacts, while operating at 9 T. Compaction was achieved by pressing the punches between the closed end of the press tube and the hydraulic cylinder mounted on the opposite end. Improvements up to 10% in magnetization and 20% in energy products of the permanent magnets were obtained, as the alignment fields were increased above the 2-T maximum field of the electromagnets used in industry. Increases in magnetization of 3% are significant in the mature sintered magnet industry

Corrosion resistant zirconium alloys prepared by powder metallurgy

International Nuclear Information System (INIS)

Wojeik, C.C.

1984-01-01

Pure zirconium and zirconium 2.5% niobium were prepared by powder metallurgy. The powders were prepared directly from sponge and consolidated by cold isostatic pressing and sintering. Hot isostatic pressing was also used to obtain full density after sintering. For pure zirconium the effects of particle size, compaction pressure, sintering temperature and purity were investigated. Fully densified zirconium and Zr-2.5%Nb exhibited tensile properties comparable to cast material at room temperature and 300 0 F (149 0 C). Pressed and sintered material having density of 94-99% had slightly lower tensile properties. Corrosion tests were performed in boiling 65% H/sub 2/SO/sub 4/, 70% HNO/sub 3/, 20% HCl and 20% HCl + 500 ppm FeCl/sub 3/ (a known pitting solution). For fully dense material the observed corrosion behavior was nearly equivalent to cast material. A slightly higher rate of attack was observed for samples which were only 94-99% dense. Welding tests were also performed on zirconium and Zr-2.5%Nb alloy. Unlike P/M titanium alloys, these materials had good weldability due to the lower content of volatile impurities in the powder. A slight amount of weld porosity was observed but joint efficiencies were always not 100%, even for 94-99% density samples. Several practical applications of the P/M processed material will be briefly described

Production of glass or glass-ceramic to metal seals with the application of pressure

Science.gov (United States)

Kelly, Michael D.; Kramer, Daniel P.

1987-11-10

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Casting defects and high temperature fatigue life of IN 713LC superalloy

Czech Academy of Sciences Publication Activity Database

Kunz, Ludvík; Lukáš, Petr; Konečná, R.; Fintová, S.

2012-01-01

Roč. 41, AUG (2012), s. 47-51 ISSN 0142-1123 R&D Projects: GA MPO(CZ) FR-TI3/055; GA MŠk(CZ) ED1.1.00/02.0068 Institutional support: RVO:68081723 Keywords : IN 713LC * High-cycle fatigue * casting defects * hot isostatic pressing * extreme value statistics Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 1.976, year: 2012

Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

Science.gov (United States)

Harf, Fredric H.

1989-01-01

Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

Application of hot isostatic pressing to the manufacture of complex shaped moulds and tools

International Nuclear Information System (INIS)

Rigal, E.; Baccino, R.; Federzoni, L.; Moret, F.

2000-01-01

In this article, we briefly recall the physical mechanisms at the origin of the Barkhausen effect in ferromagnetic mediums and the thermoelectric power in conductor metals. We then present, for each of these phenomena, the measurement principles and their sensitivity to the microstructural state, notably in the case of precipitation phenomena and in the ones linked to plastic deformation. Finally, in the case of the formation of precipitates in an iron-based alloy, we show the complementarity of both techniques. (authors)

Flexural strength and the probability of failure of cold isostatic pressed zirconia core ceramics.

Science.gov (United States)

Siarampi, Eleni; Kontonasaki, Eleana; Papadopoulou, Lambrini; Kantiranis, Nikolaos; Zorba, Triantafillia; Paraskevopoulos, Konstantinos M; Koidis, Petros

2012-08-01

The flexural strength of zirconia core ceramics must predictably withstand the high stresses developed during oral function. The in-depth interpretation of strength parameters and the probability of failure during clinical performance could assist the clinician in selecting the optimum materials while planning treatment. The purpose of this study was to evaluate the flexural strength based on survival probability and Weibull statistical analysis of 2 zirconia cores for ceramic restorations. Twenty bar-shaped specimens were milled from 2 core ceramics, IPS e.max ZirCAD and Wieland ZENO Zr, and were loaded until fracture according to ISO 6872 (3-point bending test). An independent samples t test was used to assess significant differences of fracture strength (α=.05). Weibull statistical analysis of the flexural strength data provided 2 parameter estimates: Weibull modulus (m) and characteristic strength (σ(0)). The fractured surfaces of the specimens were evaluated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The investigation of the crystallographic state of the materials was performed with x-ray diffraction analysis (XRD) and Fourier transform infrared (FTIR) spectroscopy. Higher mean flexural strength (Plines zones). Both groups primarily sustained the tetragonal phase of zirconia and a negligible amount of the monoclinic phase. Although both zirconia ceramics presented similar fractographic and crystallographic properties, the higher flexural strength of WZ ceramics was associated with a lower m and more voids in their microstructure. These findings suggest a greater scattering of strength values and a flaw distribution that are expected to increase failure probability. Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Hot isostatically pressed (HIPed) thick-walled component for a pressurised water reactor (PWR) application

International Nuclear Information System (INIS)

Hookham, I.; Burdett, B.; Bridger, K.; Sulley, J.L.

2009-01-01

This paper presents the work conducted to justify and provide a quality assured HIPed thick-walled component for a PWR application; the component being designed and manufactured by Rolls-Royce. Rolls-Royce has previously published (ICAPP 08) its overall, staged approach to the introduction of powder HIPed components; starting with thin-walled, leak limited pressure boundaries, and culminating in the use of the powder HIPed process for thick walled components. This paper presents details specific to a thick walled pressure vessel component. Results are presented of non-destructive and destructive examinations of one of a batch of components. Mechanical testing and metallurgical examination results of sample material taken from different sections of the component are presented. A full range of test results is provided covering, as examples: tensile, Charpy impact and sensitization susceptibility. Differences in weldability between the HIPed and the previous forged form are also documented. (author)

Repercussão da pressão positiva expiratória final na pressão de perfusão cerebral em pacientes adultos com acidente vascular hemorrágico

OpenAIRE

Lima,Wildberg Alencar; Campelo,Antônio Roberto Leite; Gomes,Rodrigo Luís Mousinho; Brandão,Daniella Cunha

2011-01-01

A pressão positiva intratorácica pode levar a alterações hemodinâmicas com repercussão no compartimento intracraniano, alterando a pressão intracraniana e a pressão de perfusão cerebral. Esse efeito pode se tornar mais intenso quando utilizados elevados valores de pressão positiva expiratória final. OBJETIVO: Medir o impacto que diferentes valores de pressão positiva expiratória final causam na pressão intracraniana, na pressão de perfusão cerebral e pressão arterial média. MÉTODO: O estudo f...

Press problem related to nuclear energy news reporting

International Nuclear Information System (INIS)

Arai, Mitsuo

2008-01-01

Since the event of Niigataken Chuetsu-oki Earthquake in 2007 and the subsequent press reports on damage of nuclear power station after it, a stance of media is being questioned. In order to clear this problem, basic organizational structure of the press related to nuclear energy news was analyzed. Local news department, social news department, science news department and economical news department involve in nuclear energy news the accordance with their own situations and concerns. This structure makes problem of nuclear energy news reporting complicated. Changing this system is required but very difficult. It is concluded that the press problem around nuclear energy news is strange. (author)

PRESS FREEDOM IN SINGAPORE AND MALAYSIA: DEFAMATION

Directory of Open Access Journals (Sweden)

Georgia Kate Chapman

2015-04-01

Full Text Available This paper focuses on the arguments around restriction on freedom of the press in the Strong States of Singapore and Malaysia. It assesses the presence of constraints on press freedoms in democratic western countries imposed by corporation rather than state and the similar effects that these constraints may have on bias present in publicly accessible news reporting. It argues that independence of the press does not just require protection from legal and executive regulation, but also protection from large media corporations and their political alignments. This report will assess the bias of reporting and news media publication that exists in Malaysia and Singapore due to legislative and regulatory constraints as opposed to bias that exist in the western liberal democratic nations of the United Kingdom (UK and the United States of America (USA due to Media Organisation control.

A press for the theater

Directory of Open Access Journals (Sweden)

Luciana Penna França

2017-12-01

Full Text Available Understanding the history of the amateur theater at the end of the XIXth century and the beginning of the XXth is possible, largely, because of the newspapers dedicated to the “theatrical affairs”. Such publications are important for the quantity and the diversity, revealing not only the place occupied by the theater in the capital, but also for the recognition of the press as a means of disclosure of plays, public education and opinion, artist projection, etc, not to mention personal affairs and requests, and the exchange of favors among managers and journalists. Even more, the press production of the dramatic amateurs clubs demonstrate the understanding of its role in the dissemination of ways to act and think beyond the stage and in the everyday life.

Preliminary isostatic residual gravity anomaly map of Paso Robles 30 x 60 minute quadrangle, California

Science.gov (United States)

McPhee, D.K.; Langenheim, V.E.; Watt, J.T.

2011-01-01

This isostatic residual gravity map is part of an effort to map the three-dimensional distribution of rocks in the central California Coast Ranges and will serve as a basis for modeling the shape of basins and for determining the location and geometry of faults within the Paso Robles quadrangle. Local spatial variations in the Earth\\'s gravity field, after accounting for variations caused by elevation, terrain, and deep crustal structure reflect the distribution of densities in the mid- to upper crust. Densities often can be related to rock type, and abrupt spatial changes in density commonly mark lithological or structural boundaries. High-density rocks exposed within the central Coast Ranges include Mesozoic granitic rocks (exposed northwest of Paso Robles), Jurassic to Cretaceous marine strata of the Great Valley Sequence (exposed primarily northeast of the San Andreas fault), and Mesozoic sedimentary and volcanic rocks of the Franciscan Complex [exposed in the Santa Lucia Range and northeast of the San Andreas fault (SAF) near Parkfield, California]. Alluvial sediments and Tertiary sedimentary rocks are characterized by low densities; however, with increasing depth of burial and age, the densities of these rocks may become indistinguishable from those of older basement rocks.

Fundamental study on target plate model with high thermal conductive ceramics for fusion power plants

International Nuclear Information System (INIS)

Ishiyama, Shintaro

2004-01-01

Target plate model (35 mm x 25 mm x 100 mm) of divertor device for fusion reactor was fabricated using low activated and light material, Si/xSiC Metal Matrix Composite (MMC) and high strength and thermal conductive SiC. This model has bonding structure of armor tile (25 mm x 25 mm x 10 mmt) of Hot Pressed (HP) and Hot Isostatic Pressed (HIP) Si/SiC (10 wt%)-MMC and substrate (25 mm x 25 mm x 100 mm) of SiC/BeO (1 wt%) with water cooling channel (φ15 mm). Armor tile material, Si/10SiC-MMC shows high thermal conductive and low resistivity with over 200 MPa peak bending strength at high temperature. This material behaves super plasticity over peak temperature corresponding to peak bending strength and low temperature brittleness of this material was improved to degrade DBTT to 673 K by optimization of Hot Press (HP) and Hot Isostatic Press (HIP) conditions. Substrate body material, SiC/1BeO behaves major characteristics of high bending strength over 500 MPa, high density of 3.2 g/cm 3 and high thermal conductivity of 270 W/m·K at room temperature. Target plate model with water cooling by 293 K and 2 MPa pressurized water at 1 m/s was exposed under 5 MW/m 2 x 30 s high heat flux H + ion beam and showed very good cooling performance and no damage was found after this test. (author)

Flexible Description and Adaptive Processing of Earth Observation Data through the BigEarth Platform

Science.gov (United States)

Gorgan, Dorian; Bacu, Victor; Stefanut, Teodor; Nandra, Cosmin; Mihon, Danut

2016-04-01

of some Earth Observation oriented applications based on flexible description of processing, and adaptive and portable execution over Cloud infrastructure. Main references for further information: [1] BigEarth project, http://cgis.utcluj.ro/projects/bigearth [2] Gorgan, D., "Flexible and Adaptive Processing of Earth Observation Data over High Performance Computation Architectures", International Conference and Exhibition Satellite 2015, August 17-19, Houston, Texas, USA. [3] Mihon, D., Bacu, V., Colceriu, V., Gorgan, D., "Modeling of Earth Observation Use Cases through the KEOPS System", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp. 455-460, (2015). [4] Nandra, C., Gorgan, D., "Workflow Description Language for Defining Big Earth Data Processing Tasks", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp. 461-468, (2015). [5] Bacu, V., Stefan, T., Gorgan, D., "Adaptive Processing of Earth Observation Data on Cloud Infrastructures Based on Workflow Description", Proceedings of the Intelligent Computer Communication and Processing (ICCP), IEEE-Press, pp.444-454, (2015).

Planet Press: an EGU initiative to bring geoscientific research to children

Science.gov (United States)

Ferreira, Bárbara

2016-04-01

Planet Press (http://www.egu.eu/education/planet-press/) is an EGU educational project that aims to get children (mainly 7-13 year olds), as well as their parents and educators, interested in and engaged with up-to-date scientific research and news. Planet Press articles are short versions of EGU press releases written in child-friendly language. Because EGU press releases cover research published in the various EGU scientific journals, Planet Press focuses on topics as varied as air pollution, glaciers, climate change, earthquakes, ocean sciences, droughts and floods, or space sciences. The texts are reviewed by both scientists and educators to make sure they are accurate and clear to their target audience. By sharing new and exciting geoscientific research with young kids, we hope to inspire them to develop an interest in the Earth, planetary and space sciences. In this presentation, we describe how the Planet Press idea came about, how the project is run, and the challenges and lessons learnt since the launch of this educational initiative in 2014. Planet Press, which has the support of the EGU Committee on Education, is made possible by the work of volunteer scientists and educators who review and translate the texts. We are grateful for the help of Jane Robb, former EGU Educational Fellow, with launching the project. Planet Press is inspired by Space Scoop (http://www.spacescoop.org/), an initiative by UNAWE, the EU-Universe Awareness organisation, that brings astronomy news to children every week.

Phase-Division-Based Dynamic Optimization of Linkages for Drawing Servo Presses

Science.gov (United States)

Zhang, Zhi-Gang; Wang, Li-Ping; Cao, Yan-Ke

2017-11-01

Existing linkage-optimization methods are designed for mechanical presses; few can be directly used for servo presses, so development of the servo press is limited. Based on the complementarity of linkage optimization and motion planning, a phase-division-based linkage-optimization model for a drawing servo press is established. Considering the motion-planning principles of a drawing servo press, and taking account of work rating and efficiency, the constraints of the optimization model are constructed. Linkage is optimized in two modes: use of either constant eccentric speed or constant slide speed in the work segments. The performances of optimized linkages are compared with those of a mature linkage SL4-2000A, which is optimized by a traditional method. The results show that the work rating of a drawing servo press equipped with linkages optimized by this new method improved and the root-mean-square torque of the servo motors is reduced by more than 10%. This research provides a promising method for designing energy-saving drawing servo presses with high work ratings.

Method for hot pressing irregularly shaped refractory articles

Science.gov (United States)

Steinkamp, William E.; Ballard, Ambrose H.

1982-01-01

The present invention is directed to a method for hot pressing irregularly haped refractory articles with these articles of varying thickness being provided with high uniform density and dimensional accuracy. Two partially pressed compacts of the refractory material are placed in a die cavity between displaceable die punches having compact-contacting surfaces of the desired article configuration. A floating, rotatable block is disposed between the compacts. The displacement of the die punches towards one another causes the block to rotate about an axis normal to the direction of movement of the die punches to uniformly distribute the pressure loading upon the compacts for maintaining substantially equal volume displacement of the powder material during the hot pressing operation.

Modularity of Pressing Tools for Screw Press Producing Solid Biofuels

Directory of Open Access Journals (Sweden)

Miloš Matúš

2012-01-01

Full Text Available This paper focuses on the development of the newly-patented structure of a screw briquetting machine for compacting biomass into a solid biofuel. The design of the machine is based on the results of a comprehensive study of the complicated process of biomass compaction. The patented structure meets two main goals: the elimination of axial forces, leading to increased lifetime of the bearings, and the new modular design of a pressing chamber and tools with their geometry based on the application of a mathematical model.

ALUMINUM BOX BUNDLING PRESS

Directory of Open Access Journals (Sweden)

Iosif DUMITRESCU

2015-05-01

Full Text Available In municipal solid waste, aluminum is the main nonferrous metal, approximately 80- 85% of the total nonferrous metals. The income per ton gained from aluminum recuperation is 20 times higher than from glass, steel boxes or paper recuperation. The object of this paper is the design of a 300 kN press for aluminum box bundling.

Performance of planar single cell lanthanum gallate based solid oxide fuel cells

Energy Technology Data Exchange (ETDEWEB)

Maffei, N.; Kuriakose, A.K. [Materials Technology Labs., CANMET, Natural Resources Canada, Ottawa, ON (Canada)

1998-09-01

A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700 C with respect to the J-V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen. (orig.)

Performance of planar single cell lanthanum gallate based solid oxide fuel cells

Science.gov (United States)

Maffei, N.; Kuriakose, A. K.

A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700°C with respect to the J- V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen.

Densification of YBa2Cu3O7-x

International Nuclear Information System (INIS)

Zhou, J.P.; Sorrell, C.C.; Dou, S.X.; Liu, H.K.; Bourdillon, A.J.

1991-01-01

YBa 2 Cu 3 O 7-x is normally densified by solid-state reaction at 935deg-980deg C for 2-4 h in air or at 940deg-1000deg C for 5-10 h in flowing oxygen. Typical densities achieved these ways are 70-80% of theoretical. Rahaman et al. obtained 95% density by rapidly inserting samples in a furnace at 800deg C. Densities of 94-100% can be achieved by sinter-forging, hot pressing, and hot isostatic pressing. The present work reports a rapid sintering technique whereby 100% density can be achieved without the use of specialised equipment

Hot working alkali halides for laser window applications

International Nuclear Information System (INIS)

Koepke, B.G.; Anderson, R.H.; Stokes, R.J.

1975-01-01

The techniques used to hot work alkali halide crystals into laser window blanks are reviewed. From the point of view of high power laser window applications one of the materials with a high figure of merit is KCl. Thus the materials examined are KCl and alloys of KCl-KBr containing 5 mole percent KBr. The fabrication techniques include conventional and constrained press forging, isostatic press forging and hot rolling. Optical properties are paramount to the ultimate usefulness of these materials. Results on the optical properties of the hot worked material are included together with mechanical properties and microstructural data

Silver iodide sodalite for "1"2"9I immobilisation

International Nuclear Information System (INIS)

Vance, E.R.; Gregg, D.J.; Grant, C.; Stopic, A.; Maddrell, E.R.

2016-01-01

Silver iodide sodalite was initially synthesised as a fine-grained major phase in a nominally stoichiometric composition following hot isostatic pressing at 850 °C with 100 MPa and its composition, Ag_4Al_3Si_3O_1_2I, was approximately verified by scanning electron microscopy. An alternative preparative method yielded a more dense and stoichiometric AgI sodalite on sintering and HIPing. As found for AgI, the I is released from AgI sodalite much more readily in reducing water than in ordinary water. Thus in normal PCT-B tests, the I release was <0.3 g/L in water, but it was ∼70 g/L under highly reducing conditions. This is an important point with regard to can material if HIPing is used for consolidation. - Highlights: • Dense AgI sodalite has been produced by hot isostatic pressing. • The stoichiometry of AgI sodalite has been confirmed by scanning electron microscopy. • Good I immobilisation in AgI sodalite exposed to water containing Cu or Ni metal powders was determined. • AgI sodalite exposed to water containing Fe powders decomposed and released significant quantities of iodine.

Optimization of consolidation parameters of 18Cr-ODS ferritic steel through microstructural and microtexture characterization

Science.gov (United States)

Dash, Manmath Kumar; Mythili, R.; Dasgupta, Arup; Saroja, S.

2018-04-01

This paper reports the optimization of consolidation process based on the evolution of microstructure, microtexture and densification in 18%-Cr Oxide Dispersion Strengthened steel. The steel powder of composition Fe-18Cr-0.01C-2W-0.25Ti-0.35Y2O3 has been consolidated by cold isostatic pressing (CIP) for green compaction after mechanical milling. Sintering (1000-1250 °C) and hot isostatic pressing (HIP) at 1150 °C has been employed to achieve good densification on compacted CIP specimen. The effect of sintering temperatures on densification behavior was evaluated and sintering at 1150°C was identified to be optimum for achieving good compaction (92% density) and homogeneous polygonal microstructure with a uniform distribution of fine pores. In addition, HIP of CIP product at 1150°C was found to yield a more homogeneous microstructure as compared to sintered product with 97% density. A static/dynamic recrystallization associated with (1 1 1) texture is observed during consolidation process. A statistical comparison has been made based on frequency of grain boundary distribution and associated texture with its theoretical attributes.

Utilisation of heat and pressure through the whole fuel cycle

International Nuclear Information System (INIS)

Eddowes, T.; Moricca, S.; Webb, N.

2003-01-01

Full text: The existence of the earth around us is a result of heat and pressure combined to form the very crust we stand on. With such a good model, scientists working throughout the nuclear fuel cycle have used these principles to optimise each particular step. From the fabrication of fuel rods and running of reactors to the final storage of the waste generated; heat and pressure have proved to be vital resources. At ANSTO the concepts of using heat and pressure to consolidate the waste produced for the nuclear fuel cycle have been extensively investigated. Working with collaborators, it has been demonstrated that the intermediate to high level waste can be incorporated into a ceramic or glass-ceramic matrix and immobilised therein, using heat and pressure via the means of a Hot Isostatic Press. This paper touches on how following the simple principles of heat and pressure utilised in the operation of this planet every day, the nuclear fuel cycle can be most efficient. The main focus has been the utilisation of Hot Isostatic Pressing for the production of various durable wasteforms at ANSTO for both Australian and international wastes

Press releases — the new trend in science communication

DEFF Research Database (Denmark)

Autzen, Charlotte

2014-01-01

Scientific institutions have for a long time known the importance of framing and owning stories about science They also know the effective way of communicating science in a press release This is part of the institution’s public relations. Enhanced competition among research institutions has led...... to a buildup of communicative competences and professionalization of public relations inside the institutions and the press release has become an integrated part of science communication from these institutions. Changing working conditions in the media, where fewer people have to publish more, have made press...... releases from trustworthy scientific institutions into free and easily copied content for the editors. In this commentary I investigate and discuss the communicative ecosystem of the university press release. I especially take a close look at the role of the critical and independent science journalist...

Effects of wet-pressing-induced fiber hornification on enzymatic saccharification of lignocelluloses

Science.gov (United States)

X.L. Luo; Junyong Zhu; Roland Gleisner; H.Y. Zhan

2011-01-01

This article reports the effect of wet-pressing-induced fiber hornification on enzymatic saccharification of lignocelluloses. A wet cellulosic substrate of bleached kraft eucalyptus pulp and two wet sulfite-pretreated lignocellulosic substrates of aspen and lodgepole pine were pressed to various moisture (solids) contents by variation of pressing pressure and pressing...

Finite element modelling and associated experimentations to optimize and predict the pressing cycle of a future AMBB manufacturing press

International Nuclear Information System (INIS)

Bayle, J.P.; Mezeix, P.; Tronche, E.; Delette, G.; Remy, E.; Picart, S.

2014-01-01

This study presents an approach based on the use of pellet forming numerical digital simulation which enables optimization of the die pressing cycle. Semi-empirical mechanical models were used in an FEM code, CAST3M. Specific powder characterizations were also performed to supply the mechanical parameters of compaction model. The methodology for the identification of five main coefficients (index flow, elastic and plastic parameters) was used with two different powders. The results show that the axial distribution of frictional forces may be changed during die pressing by a modification of the sequence of punch displacements. According to these results and the literature, the pressing cycle can be considered to have an influence on the shape of a sintered pellet through the axial distribution of green density. The process used for the identification of the Cam-Clay model coefficients seems to be in good agreement, even if the changes in certain parameters remain rather unclear and will require follow-up studies to confirm some of the results. The experimental device used produces good quality pellets, and the Radial Open Die Modulus remains the first choice for reduced pellet damage. Much work still remains to be done to fully define the identification process and create the most representative simulations possible before launching an industrial version of a nuclearized press, planned for the last quarter of year 2014. (authors)

Local and international press digest

CERN Multimedia

2008-01-01

The following are the top stories in the Maltese and the international press today. The Times gives prominence to the Prime Minister's flying visit to Geneva yesterday, where he signed a research cooperation agreement with CERN, the European nuclear research organisation.

Improvement of nuclear reactor component materials by application of hot isostatic processing (HIP). Survey report on Phase 1

International Nuclear Information System (INIS)

Mueller, J.J.

1975-12-01

The report summarizes the results of an EPRI-sponsored state-of-the-art survey of hot isostatic processing (HIP). The purpose of the study was to identify potential nuclear plant applications of HIP with high pay-off through improvement in component quality and reliability. The survey shows that HIP will reduce cost and manufacturing time and improve quality and ease of nondestructive examination of all castings for which porosity is a problem. Nuclear valves are a prime example. Tubing, pipe, and sheet and bar present other possibilities of somewhat less immediate promise. This report includes a review of some of the EPRI motivations for undertaking this research; a brief explanation of HIP, the survey methodology exployed; the basic operations in the processes studied; a review of the historical applications of HIP to problem areas consistent with those addressed in the survey; the results of the survey and associated analyses of the problems; and the recommendations and justifications for the Phase II program

Pressing and tubes rolling out of tungsten of gas phase deposition

International Nuclear Information System (INIS)

Korolev, Yu.M.; Kosachev, L.S.; Semiletov, S.S.; Solov'ev, V.F.; Sorkin, V.A.

1987-01-01

The possibility of increasing ductility of tubes of tungsten fluoride using heat treatment and plastic deformation- pressing and thermal rolling are studied. When designing the processes of treatment it should be necessarily taken into account that structural state of initial blanks as well as the ratio of deformations in radial and tangential directions under pressing with a rigid needle strongly affects technological properties of pressed tubes. The columnar structure of blanks is undesirable for its embrittlement affects the pressed tubes

Treatment of the press residues of pressed grapes on an industrial scale

Energy Technology Data Exchange (ETDEWEB)

1978-04-24

EtOH and tartaric acid are recovered from press residues of grapes by distillation and concentration of the EtOH and extraction of the dried residue after removal of seeds with a mixture of H/sub 2/O and mineral acid. Vegetable oil is extracted from the seeds. Collidal substances are coagulated by roasting prior to extraction of tartaric acid. The grape skins are recovered in flake form.

High-temperature low-cycle fatigue behaviour of HIP treated and untreated superalloy MAR-M247

Czech Academy of Sciences Publication Activity Database

Šulák, Ivo; Obrtlík, Karel; Čelko, L.

2016-01-01

Roč. 54, č. 6 (2016), s. 471-481 ISSN 0023-432X R&D Projects: GA TA ČR(CZ) TA04011525; GA ČR(CZ) GA15-20991S Institutional support: RVO:68081723 Keywords : hot isostatic pressing * high-temperature low cycle fatigue * fatigue life curves * Ni-based superalloy * dislocation structures * planar bands Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 0.366, year: 2016

Evaluation of powder metallurgical processing routes for multi-component niobium silicide-based high-temperature alloys

Energy Technology Data Exchange (ETDEWEB)

Seemueller, Hans Christoph Maximilian

2016-03-22

Niobium silicide-based composites are potential candidates to replace nickel-base superalloys for turbine applications. The goal of this work was to evaluate the feasibility and differences in ensuing properties of various powder metallurgical processing techniques that are capable of manufacturing net-shape turbine components. Two routes for powder production, mechanical alloying and gas atomization were combined with compaction via hot isostatic pressing and powder injection molding.

A Nonvolume Preserving Plasticity Theory with Applications to Powder Metallurgy

Science.gov (United States)

Cassenti, B. N.

1983-01-01

A plasticity theory has been developed to predict the mechanical response of powder metals during hot isostatic pressing. The theory parameters were obtained through an experimental program consisting of hydrostatic pressure tests, uniaxial compression and uniaxial tension tests. A nonlinear finite element code was modified to include the theory and the results of themodified code compared favorably to the results from a verification experiment.

Forming of AHSS using Servo-Presses

Science.gov (United States)

Groseclose, Adam Richard

Stamping of Advanced High Strength Steel (AHSS) alloys poses several challenges due to the material's higher strength and low formability compared to conventional steels and other problems such as (a) inconsistency of incoming material properties, (b) ductile fracture during forming, (c) higher contact pressure and temperature rise during forming, (d) higher die wear leading to reduced tool life, (e) higher forming load/press capacity, and (f) large springback leading to dimensional inaccuracy in the formed part. [Palaniswamy et. al., 2007]. The use of AHSS has been increasing steadily in automotive stamping. New AHSS alloys (TRIP, TWIP) may replace some of the Hot Stamping applications. Stamping of AHSS alloys, especially higher strength materials, 780 MPa and higher, present new challenges in obtaining good part definition (corner and fillet radii), formability (fracture and resulting scrap) and in reducing springback. Servo-drive presses, having the capability to have infinitely variable and adjustable ram speed and dwell at BDC, offer a potential improvement in quality, part definition, and springback reduction especially when the infinitely adjustable slide motion is used in combination with a CNC hydraulic cushion. Thus, it is desirable to establish a scientific/engineering basis for improving the stamping conditions in forming AHSS using a servo-drive press.

Tjekkoslovakisk presse år 2

Directory of Open Access Journals (Sweden)

Rudolf Prevratil

1991-09-01

Full Text Available Danske teleselskaber overvejer at etablere sig som kabeloperatører i Polen, mens et amerikansk selskab allerede er igang i Warszawa og Krakow. Franske lokalradionetworks opretter filialer i Polen og Tjekko- slovakiet. Den tjekkiske statsradio stiller sendenet til rådighed for Radio Free Europe. Springer-koncernen opretter en "østtysk" pendant til Bild, hvis redaktionelle hovedlinje lægger sig op ad de dybe sociale frustrati- oner, der fulgte med DDR's indlemmelse i BDR. Maxwell, Hersant og Berlusconi m.fl. etablerer sig alene eller med lokale konstellationer inden for trykt presse i flere øst- og mellemeuropæiske stater. Samtidig for- søger den tidligere undergrundspresse at vinde økonomisk og politisk fodfæste inden for markedets og "det legale samfunds" rammer, i kon- kurrence med fortidens mediemutanter og vestlige mediekoncerner. Rudolf Prevratils artikel er en refleksion over en del af de problemer, primært af økonomisk og politisk art, som har tårnet sig op for den tjek- koslovakiske presse efter fløjlsrevolutionen i november 1989. Den giver et billede af dagens situation og får gennem sine analyser påvist, at etab- lingen af en demokratisk presse i Tjekkoslovakiet ikke alene er afhængig af "hjælp udefra", men i nok så høj grad forudsætter et net af sociale og kulturelle udviklingsprocesser, som både anerkender opgøret med for- tiden og vedkender sig den historiske arv. Artiklen er oversat fra engelsk af Per Jauert.

Altimetry, gravimetry, GPS and viscoelastic modeling data for the joint inversion for glacial isostatic adjustment in Antarctica (ESA STSE Project REGINA)

Science.gov (United States)

Sasgen, Ingo; Martín-Español, Alba; Horvath, Alexander; Klemann, Volker; Petrie, Elizabeth J.; Wouters, Bert; Horwath, Martin; Pail, Roland; Bamber, Jonathan L.; Clarke, Peter J.; Konrad, Hannes; Wilson, Terry; Drinkwater, Mark R.

2018-03-01

The poorly known correction for the ongoing deformation of the solid Earth caused by glacial isostatic adjustment (GIA) is a major uncertainty in determining the mass balance of the Antarctic ice sheet from measurements of satellite gravimetry and to a lesser extent satellite altimetry. In the past decade, much progress has been made in consistently modeling ice sheet and solid Earth interactions; however, forward-modeling solutions of GIA in Antarctica remain uncertain due to the sparsity of constraints on the ice sheet evolution, as well as the Earth's rheological properties. An alternative approach towards estimating GIA is the joint inversion of multiple satellite data - namely, satellite gravimetry, satellite altimetry and GPS, which reflect, with different sensitivities, trends in recent glacial changes and GIA. Crucial to the success of this approach is the accuracy of the space-geodetic data sets. Here, we present reprocessed rates of surface-ice elevation change (Envisat/Ice, Cloud,and land Elevation Satellite, ICESat; 2003-2009), gravity field change (Gravity Recovery and Climate Experiment, GRACE; 2003-2009) and bedrock uplift (GPS; 1995-2013). The data analysis is complemented by the forward modeling of viscoelastic response functions to disc load forcing, allowing us to relate GIA-induced surface displacements with gravity changes for different rheological parameters of the solid Earth. The data and modeling results presented here are available in the PANGAEA database (https://doi.org/10.1594/PANGAEA.875745). The data sets are the input streams for the joint inversion estimate of present-day ice-mass change and GIA, focusing on Antarctica. However, the methods, code and data provided in this paper can be used to solve other problems, such as volume balances of the Antarctic ice sheet, or can be applied to other geographical regions in the case of the viscoelastic response functions. This paper presents the first of two contributions summarizing the

Altimetry, gravimetry, GPS and viscoelastic modeling data for the joint inversion for glacial isostatic adjustment in Antarctica (ESA STSE Project REGINA

Directory of Open Access Journals (Sweden)

I. Sasgen

2018-03-01

Full Text Available The poorly known correction for the ongoing deformation of the solid Earth caused by glacial isostatic adjustment (GIA is a major uncertainty in determining the mass balance of the Antarctic ice sheet from measurements of satellite gravimetry and to a lesser extent satellite altimetry. In the past decade, much progress has been made in consistently modeling ice sheet and solid Earth interactions; however, forward-modeling solutions of GIA in Antarctica remain uncertain due to the sparsity of constraints on the ice sheet evolution, as well as the Earth's rheological properties. An alternative approach towards estimating GIA is the joint inversion of multiple satellite data – namely, satellite gravimetry, satellite altimetry and GPS, which reflect, with different sensitivities, trends in recent glacial changes and GIA. Crucial to the success of this approach is the accuracy of the space-geodetic data sets. Here, we present reprocessed rates of surface-ice elevation change (Envisat/Ice, Cloud,and land Elevation Satellite, ICESat; 2003–2009, gravity field change (Gravity Recovery and Climate Experiment, GRACE; 2003–2009 and bedrock uplift (GPS; 1995–2013. The data analysis is complemented by the forward modeling of viscoelastic response functions to disc load forcing, allowing us to relate GIA-induced surface displacements with gravity changes for different rheological parameters of the solid Earth. The data and modeling results presented here are available in the PANGAEA database (https://doi.org/10.1594/PANGAEA.875745. The data sets are the input streams for the joint inversion estimate of present-day ice-mass change and GIA, focusing on Antarctica. However, the methods, code and data provided in this paper can be used to solve other problems, such as volume balances of the Antarctic ice sheet, or can be applied to other geographical regions in the case of the viscoelastic response functions. This paper presents the first of two

A Simplified Model of an Offset Ram Press for Sunflower Oil ...

African Journals Online (AJOL)

This paper presents the theoretical analysis of a simplified model of a ram press. The design of the ram press is based on the classical slider-crank mechanism. A force analysis of the press was performed for several successive positions of the driving lever (handle) and for a range of values of certain dimensionless ...

Sea level and shoreline reconstructions for the Red Sea: isostatic and tectonic considerations and implications for hominin migration out of Africa

Science.gov (United States)

Lambeck, Kurt; Purcell, Anthony; Flemming, Nicholas. C.; Vita-Finzi, Claudio; Alsharekh, Abdullah M.; Bailey, Geoffrey N.

2011-12-01

The history of sea level within the Red Sea basin impinges on several areas of research. For archaeology and prehistory, past sea levels of the southern sector define possible pathways of human dispersal out of Africa. For tectonics, the interglacial sea levels provide estimates of rates for vertical tectonics. For global sea level studies, the Red Sea sediments contain a significant record of changing water chemistry with implications on the mass exchange between oceans and ice sheets during glacial cycles. And, because of its geometry and location, the Red Sea provides a test laboratory for models of glacio-hydro-isostasy. The Red Sea margins contain incomplete records of sea level for the Late Holocene, for the Last Glacial Maximum, for the Last Interglacial and for earlier interglacials. These are usually interpreted in terms of tectonics and ocean volume changes but it is shown here that the glacio-hydro-isostatic process is an additional important component with characteristic spatial variability. Through an iterative analysis of the Holocene and interglacial evidence a separation of the tectonic, isostatic and eustatic contributions is possible and we present a predictive model for palaeo-shorelines and water depths for a time interval encompassing the period proposed for migrations of modern humans out of Africa. Principal conclusions include the following. (i) Late Holocene sea level signals evolve along the length of the Red Sea, with characteristic mid-Holocene highstands not developing in the central part. (ii) Last Interglacial sea level signals are also location dependent and, in the absence of tectonics, are not predicted to occur more than 1-2 m above present sea level. (iii) For both periods, Red Sea levels at 'expected far-field' elevations are not necessarily indicative of tectonic stability and the evidence points to a long-wavelength tectonic uplift component along both the African and Arabian northern and central sides of the Red Sea. (iv) The

Gravity measurements in southeastern Alaska reveal negative gravity rate of change caused by glacial isostatic adjustment

Science.gov (United States)

Sun, W.; Miura, S.; Sato, T.; Sugano, T.; Freymueller, J.; Kaufman, M.; Larsen, C. F.; Cross, R.; Inazu, D.

2010-12-01

For the past 300 years, southeastern Alaska has undergone rapid ice-melting and land uplift attributable to global warming. Corresponding crustal deformation (3 cm/yr) caused by the Little Ice Age retreat is detectable with modern geodetic techniques such as GPS and tidal gauge measurements. Geodetic deformation provides useful information for assessing ice-melting rates, global warming effects, and subcrustal viscosity. Nevertheless, integrated geodetic observations, including gravity measurements, are important. To detect crustal deformation caused by glacial isostatic adjustment and to elucidate the viscosity structure in southeastern Alaska, Japanese and U.S. researchers began a joint 3-year project in 2006 using GPS, Earth tide, and absolute gravity measurements. A new absolute gravity network was established, comprising five sites around Glacier Bay, near Juneau, Alaska. This paper reports the network's gravity measurements during 2006-2008. The bad ocean model in this area hindered ocean loading correction: Large tidal residuals remain in the observations. Accurate tidal correction necessitated on-site tidal observation. Results show high observation precision for all five stations: day ice thickness changes. A gravity bias of about -13.2 ± 0.1 mGal exists between the Potsdam and current FG5 gravity data.

Freedom of the Press In the Scope of Human Rights

Directory of Open Access Journals (Sweden)

Sri Ayu Astuti

2014-01-01

Full Text Available Freedom of expression and press freedom is the embodiment of the recognition of human rights. Freedom of expression is also the existence of press to disclose the news with honesty and do not get a pressure to deliver the news to the public space, which in news production is known as a work of journalism. Now the  press has gained freedom of expression in the news production process which is guaranteed in the state constitution. Although Article 28 of the Constitution of the Republic of Indonesia 1945 does not point directly at the press, However, Article 28 F emphasis on processing and storage as well as ownership, excavations to information. It also contains provisions on the freedom of expression of others, which should be valued and respected. It shows equality for everyone in his position before the law in accordance with Article 27 1945 Constitution, which emphasizes the recognition of constitutional rights that belong to every person in the state of law in the Republic of Indonesia. Thus the press, which have freedom of expression in the writings of journalistic works are required to be responsible for the published news. So as not to face the legal issues and criminalization, then press should perform tasks and functions to enforce ethics as the precautionary principle when processing the news and broadcast it to the public space, as well as upholding human rights. How To Cite: Astuti, S. (2014. Freedom of the Press In the Scope of Human Rights. Rechtsidee, 1(1, 101-118. doi:http://dx.doi.org/10.21070/jihr.v1i1.96

A virtual model of the bench press exercise.

Science.gov (United States)

Rahmani, Abderrahmane; Rambaud, Olivier; Bourdin, Muriel; Mariot, Jean-Pierre

2009-08-07

The objective of this study was to design and validate a three degrees of freedom model in the sagittal plane for the bench press exercise. The mechanical model was based on rigid segments connected by revolute and prismatic pairs, which enabled a kinematic approach and global force estimation. The method requires only three simple measurements: (i) horizontal position of the hand (x(0)); (ii) vertical displacement of the barbell (Z) and (iii) elbow angle (theta). Eight adult male throwers performed maximal concentric bench press exercises against different masses. The kinematic results showed that the vertical displacement of each segment and the global centre of mass followed the vertical displacement of the lifted mass. Consequently, the vertical velocity and acceleration of the combined centre of mass and the lifted mass were identical. Finally, for each lifted mass, there were no practical differences between forces calculated from the bench press model and those simultaneously measured with a force platform. The error was lower than 2.5%. The validity of the mechanical method was also highlighted by a standard error of the estimate (SEE) ranging from 2.0 to 6.6N in absolute terms, a coefficient of variation (CV) or =0.99 for all the lifts (pbench press exercises in both field and laboratory conditions.

Microscopic characterizations of membrane electrode assemblies prepared under different hot-pressing conditions

International Nuclear Information System (INIS)

Liang, Z.X.; Zhao, T.S.; Xu, C.; Xu, J.B.

2007-01-01

The durability of the membrane electrode assembly (MEA) for direct methanol fuel cells (DMFCs) is one of the most critical issues to be addressed before widespread commercialization of the DMFC technology. In this work, we investigated the effect of the hot-pressing duration on the performance and durability of the MEA prepared by hot-pressing technique. It was found that the 60-min hot pressing at 135 deg. C under the pressure of 4.0 MPa yielded a significantly improved MEA durability than did the 3-min hot pressing (a typical duration in practice) under the same condition, but no substantial difference was found in the cell performance of the MEAs prepared with the two different hot-pressing durations. The reason why the hot-pressing duration had no significant effect on cell performance is explained based on X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) characterizations of the changes in the physiochemical properties of MEAs and their constituent components, including the anode, cathode and Nafion membrane, before and after hot pressing with different durations

New Realities for Scholarly Presses in Trying Economic Times

Science.gov (United States)

Blakesley, David

2014-01-01

The author explains that Parlor Press is an independent publisher and distributor of scholarly and trade books in print and digital formats. It was founded in 2002 to address the need for an alternative scholarly, academic press attentive to emergent ideas and forms while maintaining the highest possible standards of quality, credibility, and…

Corporate social responsibility's discourse in lithuanian business press

OpenAIRE

Marčenkovas, Marius

2014-01-01

The object of this master work is corporate social responsibility's (CSR) discourse. The purpose of this work is to analyze how Lithuanian business press presents CSR topic. The main tasks to reach this purpose are: overview and compare CSR definitions; analyze media impact to CSR; analyze and summarize CSR discourse in Lithuanian business press. Literature analysis, synthesis and comparative methods were used to drawn conclusions. After the literature analysis of such scientists as Ph. Kotle...

Press/Pulse: Explaining selective terrestrial extinctions at the Cretaceous/Palaeogene boundary

Science.gov (United States)

Arens, Nan Crystal

2010-05-01

Single-cause mass extinction scenarios require extreme conditions to generate sufficiently strong kill mechanisms. Such dire effects are commonly at odds with the taxonomic selectivity that characterizes most extinction events. In response, some researchers have proposed that the interaction of a variety of factors typify episodes of elevated extinction. Previous work (Arens & West 2008 Paleobiology 34:456-471) has shown that a combination of press and pulse disturbances increases the probability of elevated extinction. The press/pulse contrast is borrowed from community ecology, where researchers have long recognized that the ecological response to long-term stress differs from that of an instantaneous catastrophe. Scaled to the macroevolutionary level, press disturbances alter community composition by placing multigenerational stress on populations. Press disturbances do not necessarily cause mortality, but reduce population size by a variety of mechanisms such as curtailed reproduction. Pulse disturbances are sudden catastrophic events that cause extensive mortality. Either press or pulse disturbances of sufficient magnitude can cause extinction, however elevated extinction occurs more commonly during the coincidence of lower-magnitude press and pulse events. The Cretaceous/Palaeogene (K/P) extinction is one of the best examples of a press/pulse extinction. Deccan Trap volcanism, which straddled the K/P boundary, altered atmospheric composition and climate. This episodic volcanism likely contributed to the climate instability observed in terrestrial ecosystems and exerted press stress. Pulse disturbance was produced by bolide impact, which punctuated the end of the Cretaceous. The press/pulse mechanism also more effectively explains selectivity in terrestrial vertebrate and plant extinctions at the K/P boundary than do single-mechanisms scenarios. For example, why do environmentally sensitive vertebrates such as amphibians experience no extinction? And why do

A Low-Cost Auto-Stop Hydraulic Press for Making KBr Disc

Science.gov (United States)

Hon, Ping-Kay

1998-05-01

A hydraulic press fitted with an adjustable torque wrench, together with a stand made of iron bars will form an auto-stop hydraulic press for making KBr disc in IR studies. Total material cost is about $100. All parts are readily available from the local hardware stores. The modified torque wrench is also useful to replace the lever in the standard laboratory press.

Fabrication and characterization of powder metallurgy tantalum components prepared by high compaction pressure technique

Energy Technology Data Exchange (ETDEWEB)

Kim, Youngmoo [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Agency for Defense Development, Yuseong, P.O. Box 35, Yuseong-gu, Daejeon 34186, Republic of Korea. (Korea, Republic of); Lee, Dongju [Korea Atomic Energy Research Institute, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Hwang, Jaewon [Samsung Electronics, 129 Samsung-ro, Youngtong-gu, Suwon 16677 (Korea, Republic of); Ryu, Ho Jin, E-mail: hojinryu@kaist.ac.kr [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Hong, Soon Hyung, E-mail: shhong@kaist.ac.kr [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of)

2016-04-15

The present study has investigated the consolidation behaviors of tantalum powders during compaction and sintering, and the characteristics of sintered components. For die compaction, the densification behaviors of the powders are simulated by finite element analyses based on the yield function proposed by Shima and Oyane. Accordingly, the green density distribution for coarser particles is predicted to be more uniform because they exhibits higher initial relative tap density owing to lower interparticle friction. It is also found that cold isostatic pressing is capable of producing higher dense compacts compared to the die pressing. However, unlike the compaction behavior, the sintered density of smaller particles is found to be higher than those of coarser ones owing to their higher specific surface area. The maximum sintered density was found to be 0.96 of theoretical density where smaller particles were pressed isostatically at 400 MPa followed by sintering at 2000 °C. Moreover, the effects of processing conditions on grain size and texture were also investigated. The average grain size of the sintered specimen is 30.29 μm and its texture is less than 2 times random intensity. Consequently, it is concluded that the higher pressure compaction technique is beneficial to produce high dense and texture-free tantalum components compared to hot pressing and spark plasma sintering. - Highlights: • Higher Ta density is obtained from higher pressure and sintering temperature. • High compaction method enables P/M Ta to achieve the density of 16.00 g·cm{sup −3}. • A P/M Ta component with fine microstructure and random orientation is developed.

A new cleaner process to prepare pressing-powder

Directory of Open Access Journals (Sweden)

Shu, Z.

2011-10-01

Full Text Available An alternative cleaner process of pressing-powder preparation, based on filter-pressing and a novel granulation method, is presented to substitute the existing spray-drying process. In the new process, about two-thirds of wet-milled slurry is filterpressed, dried and milled into dry fine powder. The other one-third of the slurry and the as-obtained dry fine powder are spray-mixed in a tower, where the slurry droplets adsorb the dry powder to form granules which are then rolled and dried into a useable pressing-powder for tile pressing. The key stages, filter-pressing and granulation (consisting of spray-mixing and rolling treatment, are specially studied. The pressing-powder properties and pressing/firing behavior, and, energy/water consumption and pollution emission data are presented, and a comparison between the new process and the existing spray-drying process is made. This new process has been found to be feasible and provides a pressing-powder with suitable properties, together with lower energy/water consumption and pollution emission (particulate matter and CO₂.

En ese trabajo se presenta un proceso alternativo y más ecológico para la preparación de polvo de prensas por molienda vía húmeda de las materias primas. En este proceso la eliminación del agua de la suspensión obtenida en la etapa de molienda, en vez de realizarse por secado por atomización, se lleva a cabo en dos etapas, en una primera etapa dos tercios de esta suspensión se filtro-prensan, posteriormente se secan y molturan hasta obtener un polvo seco micronizado. Este material seco se introduce por la parte superior de una torre granuladora, en la que se pulveriza el tercio de la suspensión restante por la parte inferior, de forma que las gotas adsorben sobre su superficie las partículas secas formando gránulos, que posteriormente se compactan por rodamiento (“rolling”, y finalmente se secan hasta la humedad requerida para el prensado. En

Quid pro quo: tobacco companies and the black press.

Science.gov (United States)

McCandless, Phyra M; Yerger, Valerie B; Malone, Ruth E

2012-04-01

We explored the relationship between tobacco companies and the Black press, which plays an important role in conveying information and opinions to Black communities. In this archival case study, we analyzed data from internal tobacco industry documents and archives of the National Newspaper Publishers Association (NNPA), the trade association of the Black press. In exchange for advertising dollars and other support, the tobacco industry expected and received support from Black newspapers for tobacco industry policy positions. Beginning in the 1990s, resistance from within the Black community and reduced advertising budgets created counterpressures. The tobacco industry, however, continued to sustain NNPA support. The quid pro quo between tobacco companies and the Black press violated journalistic standards and represented an unequal trade. Although numerous factors explain today's tobacco-related health disparities, the Black press's service to tobacco companies is problematic because of the trust that the community placed in such media. Understanding the relationship between the tobacco industry and the NNPA provides insight into strategies that the tobacco industry may use in other communities and countries.

TA-03-0035 Press Building – D&D

Energy Technology Data Exchange (ETDEWEB)

Hasenack, Marvin Leroy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-02

The Press Building was constructed in 1954 with 15,073 ft² of floor space. It was built to house a 5000 ton double action Lake Erie hydraulic press and a uranium casting area. Missions included uranium activities associated with the Nuclear Weapons and Rover Rocket programs. At the end of the Rover program, the building continued to support various uranium materials science projects until the building was placed into a cold and dark status in 2013 and then was demolished in 2017. The building interior, the press, and associated systems were radiological contaminated and disposed of as low level waste. The demolition of this building opened up valuable real estate in the TA-3 area for the future construction of an ~11,000 Sq. Ft. Biosafety Level 2 laboratory and office building. This building will support the ongoing Bioscience Division mission at the laboratory.

Parts on Demand: Evaluation of Approaches to Achieve Flexible Manufacturing Systems for Navy Partson Demand. Volume 1

Science.gov (United States)

1984-02-01

R&D efforts reviewed. The resulting assessment highlighted the generic enabling technologies and cross- cutting R&D projects required to focus current...supplied by spot buys, and which may generate Navy Inventory Control Numbers (NICN). Random samples of data were extracted from the Master Data File ( MDF ...isostatic presses, rotary forging (both hot and cold), investment casting, 0and hammer forging. Other techniques such as a laser sculpting and implosion

Cause of pitting in beryllium

International Nuclear Information System (INIS)

Kershaw, R.P.

1982-01-01

Light microscopy, bare-film radiography, secondary ion mass spectroscopy, electron microprobe and physical testing were used to examine beryllium specimens exhibiting a stratified, pitted, pattern after chemical milling. The objective was to find the cause of this pattern. Specimens were found to have voids in excess of density specification allowances. These voids are attributed, at least in part, to the sublimation of beryllium fluoride during the vacuum hot pressing operation. The origin of the pattern is attributed to these voids and etching out of fines and associated impurities. Hot isostatic pressing with a subsequent heat treatment close residual porosity and dispersed impurities enough to correct the problem

Preparation of synthetic standard minerals

International Nuclear Information System (INIS)

Herrick, C.C.; Bustamante, S.J.; Charls, R.W.; Cowan, R.E.; Hakkila, E.A.; Hull, D.E.; Olinger, B.W.; Roof, R.B.; Sheinberg, H.; Herrick, G.C.

1978-01-01

A number of techniques for synthetic mineral preparations have been examined. These techniques include hot-pressing in graphite dies at moderate pressures, high-pressure, high-temperature synthesis in a piston and cylinder apparatus, isostatic pressing under helium gas pressures, hydrous mineral preparations using water as the pressure medium, explosion-generated shock waves, and radiofrequency heating. Minerals suitable for equation-of-state studies (three-inch, high-density discs), for thermodynamic property determinations (low-density powders) and for microprobe standards (fusion-cast microbeads) have been prepared. Mechanical stress-strain calculations in the piston-cylinder apparatus have been initiated and their integration with thermal stress calculations is currently under investigation

Effects of fine porosity on the fatigue behavior of a powder metallurgy superalloy

Science.gov (United States)

Miner, R. V.; Dreshfield, R. L.

1980-01-01

Hot-isostatically-pressed powder-metallurgy Astroloy was obtained which contained 1.4 percent porosity at the grain boundaries produced by argon entering the powder container during pressing. This material was tested at 650 C in fatigue, creep-fatigue, tension, and stress-rupture and the results compared with data on sound Astroloy. They influenced fatigue crack initiation and produced a more intergranular mode of propagation but fatigue life was not drastically reduced. Fatigue behavior of the porous material showed typical correlation with tensile behavior. The plastic strain range-life relation was reduced proportionately with the reduction in tensile ductility, but the elastic strain range-life relation was changed little.

A new hot pressing technique

International Nuclear Information System (INIS)

Carcey, J.

1975-01-01

An original hot pressing method which may be applied to ceramics, metals, and refractory powders is described. The products obtained are fine grained polycristalline materials, with homogeneous structure, very high density, unstrained and of very large dimensions (several square meters). This process equally applies to composite materials including powders, fibers, etc.. [fr

Compaction of amorphous iron–boron powder

DEFF Research Database (Denmark)

Hendriksen, Peter Vang; Mørup, Steen; Koch, Christian

1993-01-01

Large scale practical use of bulk amorphous alloys requires the capability of molding the material to a desired design, for instance by compaction of an amorphous powder. This is a difficult task because the sintering temperature is limited by the crystallization temperature of the alloy.1 Here we......, should facilitate a compaction. The passivation layer, however, impedes a compaction. Isostatic pressing at 540 K at a pressure of 200 MPa clearly illustrated this; pellets pressed from passivated powder were much more brittle than pellets pressed from unpassivated powder. The density of the pellets...... was very low ([approximately-equal-to]25% of the density of bulk FeB). We have designed a die for uniaxial pressing in which the compaction can be performed without exposing the powder to air and have obtained densities larger than 60% of that of bulk FeB. We have reported studies of the dependence...

Hot-pressing steatite bodies; Obtencion de eseatita por prensado en caliente

Energy Technology Data Exchange (ETDEWEB)

Aparicio Arroyo, E

1967-07-01

Requirements for some special nuclear engineering ceramic shapes are: big size, impervious, dimensional accuracy and good mechanical and dielectric properties. Limitations of te conventional methods and advantages of te hot pressing techniques for the manufacturing of these shapes are discussed. Hot pressing characteristics of a certain steatite powder are studied. Occurrence of an optimum densification temperature just above the tale decomposition range is found. Experimental data show that the height/diameter ratio of the specimen has no effect on the sintering conditions. Increasing darkness from the graphite mould is detected above the optimum temperature. The hot-pressed steatite is compared with a fired dry-pressed sample of the same composition. (Author) 13 refs.

Pengaruh Temperatur Pada Proses Hot Isostatic Pressing Terhadap Porositas, Keausan Dan Mikrostruktur Sludge Powder Duralumin

OpenAIRE

Multazam, Ahmad; Suprapto, Wahyono; Pratikto, Pratikto

2014-01-01

Sludge is the starting raw material in the process of forming wheels with forging method. Performance wheels strongly influenced by the quality of sludge. Sludge should have physical properties that light , soft and easy strengthened. One material that can be used as materials for sludge are: duralumin material. Duralumin is another name for aluminum & copper alloy (Al / Cu) with a Cu content of about 4 %. Making sludge powder duralumin with powder metallurgical methods can improve the qu...

Beryllium window flange for synchrotron radiation X-ray beamline fabricated by hot isostatic press method

International Nuclear Information System (INIS)

Asaoka, Seiji; Maezawa, Hideki; Nishida, Kiyotoshi; Sakamoto, Naoki.

1995-01-01

The synchrotron radiation experimental facilities in National Laboratory for High Energy Physics are the experimental facilities for joint utilization, that possess the positron storage ring of 2.5 GeV exclusively used for synchrotron radiation. Synchrotron radiation is led through a mainstay beam channel to the laboratory, and in the beam line of X-ray, it is used for experiment through the taking-out window made of beryllium. At this time, the function of the taking-out window is to shut off between the ultrahigh vacuum in the mainstay beam channel and the atmosphere, and to cut the low energy component of synchrotron radiation spectra. The experiment using X-ray is carried out mostly in the atmosphere. The design of the efficient cooling water channel which is compatible with the flange construction is important under the high thermal load of synchrotron radiation. The beryllium window flange for synchrotron radiation X-ray was made by HIP method, and the ultrahigh vacuum test, the high pressure water flow test and the actual machine test were carried out by heat cycle. The properties required for the window material, the requirement of the construction, the new development of HIP method, and the experiments for evaluating the manufactured beryllium window are described. (K.I.)

La2O3-reinforced W and W-V alloys produced by hot isostatic pressing

International Nuclear Information System (INIS)

Munoz, A.; Monge, M.A.; Savoini, B.; Rabanal, M.E.; Garces, G.; Pareja, R.

2011-01-01

W and W-V alloys reinforced with La 2 O 3 particles have been produced by MA and subsequent HIP at 1573 K and 195 MPa. The microstructure of the consolidated alloys has been characterized by scanning electron microscopy, energy dispersive spectroscopy analyses and X-ray diffraction. The mechanical properties were studied by nanoindentation measurements. The results show that practically full dense billets of W-V, W-V-La 2 O 3 and W-La 2 O 3 alloys can be produced. The microstructure analysis has shown that islands of V are present in W-V and W-V-1La 2 O 3 alloys. In W-1La 2 O 3 islands of La 2 O 3 are also present. The nanohardness of the W matrix increases with the addition of V, while decreases with the addition of La 2 O 3 .

Effects of thermally induced porosity on an as-HIP powder metallurgy superalloy

Science.gov (United States)

Dreshfield, R. L.; Miner, R. V., Jr.

1980-01-01

The effect of thermally induced porosity on the mechanical properties of an as-hot-isostatically pressed and heat-treated pressing made from low carbon Astroloy is examined. Tensile, stress-rupture, creep, and low cycle fatigue tests were performed and the results were compared with industrial acceptance criteria. It is shown that the porous pressing has a porosity gradient from the rim to the bore with the bore having 1-1/2% greater porosity. Mechanical properties of the test ring below acceptance level are tensile reduction in area at room temperature and 538 C and time for 0.1% creep at 704 C. It is also found that the strength, ductility, and rupture life of the rim are slightly inferior to those of the rim of the sound pressings, while those of the bore are generally below the acceptable level. At strain ranges typical of commercial aircraft engines, the low cycle fatigue life of the rim of the porous pressings is slightly lower than that of the sound pressings.

Participation spaces for the construction of collective memory in the Spanish digital press

Directory of Open Access Journals (Sweden)

Pedro MOLINA RODRÍGUEZ-NAVAS

2014-10-01

Full Text Available The Spanish press has published digital spaces dedicated to the recovery of democratic historical memory or personal memory citizenship in general. To do has requested the participation of users. Mostly, the contributions have included personal photographic materials with or without descriptive accounts but in other cases the forms of intervention have been different.In this paper we analyze the main areas of this type that have been published in recent years. We study your objectives and forms of participation required and the final documents. The analysis results allow us to see what formulas have been successful and what elements are involved to get it.Finally, the conclusions we make a series of recommendations regarding the patterns of participation and the construction of spaces that truly allow us to relate personal stories with the general history, thus making contributions to the collective memory from new knowledge paradigms chords with the network society and social diversity.

NÉOLOGISMES ÉCONOMIQUES DANS LA PRESSE ITALIENNE D’INFORMATION GÉNÉRALE

Directory of Open Access Journals (Sweden)

Catarig Andra Teodora

2008-05-01

Full Text Available The written press is a continuously evolving organism, playing an important part in spreading the linguistic patterns. It is the privileged support of innovation, because it presents accurate facts, takes over the innovations from the specialized language and meanwhile it creates new words out of the necessity of naming the new objects, concepts and phenomena, but even out of stylistic reason or out of their desire to captivate the readers. In the present paper we define our goal as being the identification and the description of neologisms present in the economic section of two Italian daily newspapers of general interest, Corriere della Sera and La Repubblica. This section defines itself through a great number of neologisms in comparison to the other sections. Some of them have immediate success and enter the common language, being immediately recorded in the dictionary; others are ephemeral, closely connected to certain events with no implications and that don’t start another series of events.

Process design of press hardening with gradient material property influence

International Nuclear Information System (INIS)

Neugebauer, R.; Schieck, F.; Rautenstrauch, A.

2011-01-01

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

Direction-specific recruitment of rotator cuff muscles during bench press and row.

Science.gov (United States)

Wattanaprakornkul, Duangjai; Halaki, Mark; Cathers, Ian; Ginn, Karen A

2011-12-01

Recent studies indicate that rotator cuff (RC) muscles are recruited in a reciprocal, direction-specific pattern during shoulder flexion and extension exercises. The main purpose of this study was to determine if similar reciprocal RC recruitment occurs during bench press (flexion-like) and row (extension-like) exercises. In addition, shoulder muscle activity was comprehensively compared between bench press and flexion; row and extension; and bench press and row exercises. Electromyographic (EMG) activity was recorded from 9 shoulder muscles sites in 15 normal volunteers. All exercises were performed at 20, 50 and 70% of subjects' maximal load. EMG data were normalized to standard maximal voluntary contractions. Infraspinatus activity was significantly higher than subscapularis during bench press, with the converse pattern during the row exercise. Significant differences in activity levels were found in pectoralis major, deltoid and trapezius between the bench press and flexion exercises and in lower trapezius between the row and extension exercises. During bench press and row exercises, the recruitment pattern in each active muscle did not vary with load. During bench press and row exercises, RC muscles contract in a reciprocal direction-specific manner in their role as shoulder joint dynamic stabilizers to counterbalance antero-posterior translation forces. Copyright © 2011 Elsevier Ltd. All rights reserved.

Narratives of Suffering in the Press: the construction of scenes and the place of the subject

Directory of Open Access Journals (Sweden)

Danila Cal

2015-12-01

Full Text Available The article seeks to understand the narrative strategies mobilized by press journalism to expose scenes of suffering related to child domestic labor, considered by social organizations as one of the activities in which children and adolescents are more oppressed and have their rights violated. It starts with the theoretical discussion of "politics of pity" (H. Arendt in order to understand in journalistic narratives the suffering appropriations considering the narrative configuration of scenes and of the suffering subject. It explores ethical issues underlying these reports, questioning narrative strategies which are commonly recommended to reporters, as the thematization of injustices in the form of the complaint and a description of characters and life stories in the narratives. It concludes, in the light of the language of pity, that these stories are decisive for how child domestic labor is configured or not as a public issue and to understand the gestures of portrayal the suffering in the journalistic narratives.The article seeks to understand the narrative strategies mobilized by press journalism to expose scenes of suffering related to child domestic labor, considered by social organizations as one of the activities in which children and adolescents are more oppressed and have their rights violated. It starts with the theoretical discussion of "politics of pity" (H. Arendt in order to understand in journalistic narratives the suffering appropriations considering the narrative configuration of scenes and of the suffering subject. It explores ethical issues underlying these reports, questioning narrative strategies which are commonly recommended to reporters, as the thematization of injustices in the form of the complaint and a description of characters and life stories in the narratives. It concludes, in the light of the language of pity, that these stories are decisive for how child domestic labor is configured or not as a public issue

Law and the Student Press.

Science.gov (United States)

Stevens, George E.; Webster, John B.

Court cases and legal decisions involving the student press in the late 1960s and early 1970s are brought together in this book in order to show how the law has been applied to school officials and student journalists in high school, college, and the underground. The ten chapters cover the following topics: censorship, libel, obscenity, contempt,…

Effect of friction stirring on microstructure in equal channel angular pressed aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Sato, Y.S.; Urata, M.; Kokawa, H.; Ikeda, K. [Dept. of Materials Processing, Graduate School of Engineering, Tohoku Univ., Aoba-yama, Sendai (Japan)

2003-07-01

Friction stir welding (FSW) was applied to equal channel angular (ECA) pressed aluminum (Al) alloys with high strength and toughness, and the effect of FSW on microstructure and the hardness profile in ECA-pressed alloys was examined. In the weld of ECA-pressed Al alloy 1050 and 5083, the stir zone had roughly the same hardness as the ECA-pressed material, while the hardness was slightly reduced in the thermo-mechanically affected zone (TMAZ). The reduction of hardness in the TMAZ was due to dynamic recovery of dislocation cells of the ECA-pressed material. The addition of Zr to Al suppressed the reduction of hardness in the TMAZ. Consequently, friction stir (FS) weld of Al-Zr alloy retained the hardness of the ECA-pressed material throughout the weld. (orig.)

Microstructure and mechanical analysis of W/P91 steel HIP-joint with Ti interlayer

Energy Technology Data Exchange (ETDEWEB)

Wang, Ji-chao [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Wang, Wanjing, E-mail: wjwang@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Sun, Zhaoxuan; Wang, Xingli; Wei, Ran [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Xie, Chunyi; Li, Qiang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Luo, Guang-nan [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Hefei Center for Physical Science and Technology, Hefei, 230022 (China); Hefei Science Center of Chinese Academy of Sciences, Hefei, 230027 (China)

2016-11-15

Highlights: • W and P91 steel can be joined successfully using the Hot Isostatic Pressing (HIP) method with Ti interlayer. • The experiment was conducted at 760 °C below the P91 steel austenitizing temperature with the pressure 150 MPa for 4 h. • The residual stress concentration is responsible for the fracture of HIP joints under low joining temperature. • Low temperature can reduce the reaction products and improve the mechanical properties of W/Ti/P91 steel joints. - Abstract: W and P91 steel were joined by using the Hot Isostatic Pressing method with Ti interlayer, and the experiments were conducted at 760 °C. The mechanical property, bonding quality and interface microstructure were tested by the Torsion test, Non-Destructive Test, Scanning Electron Microscope and Nano-indentation test. The minimum shear strength of joints was 225 MPa and the failure occurred at the W/Ti interfaces. Metallographic analysis revealed good bonding quality across bonding lines. Almost no reaction products were found in the diffusion region and the Nano-indentation test demonstrated that the solid solution strengthening was caused by inter-diffusion in the diffusion zone. The effect of low joining temperature on reducing reaction products and improving mechanical properties of W/Ti/Steel diffusion bonding were investigated in this paper.

Microstructure and mechanical analysis of W/P91 steel HIP-joint with Ti interlayer

International Nuclear Information System (INIS)

Wang, Ji-chao; Wang, Wanjing; Sun, Zhaoxuan; Wang, Xingli; Wei, Ran; Xie, Chunyi; Li, Qiang; Luo, Guang-nan

2016-01-01

Highlights: • W and P91 steel can be joined successfully using the Hot Isostatic Pressing (HIP) method with Ti interlayer. • The experiment was conducted at 760 °C below the P91 steel austenitizing temperature with the pressure 150 MPa for 4 h. • The residual stress concentration is responsible for the fracture of HIP joints under low joining temperature. • Low temperature can reduce the reaction products and improve the mechanical properties of W/Ti/P91 steel joints. - Abstract: W and P91 steel were joined by using the Hot Isostatic Pressing method with Ti interlayer, and the experiments were conducted at 760 °C. The mechanical property, bonding quality and interface microstructure were tested by the Torsion test, Non-Destructive Test, Scanning Electron Microscope and Nano-indentation test. The minimum shear strength of joints was 225 MPa and the failure occurred at the W/Ti interfaces. Metallographic analysis revealed good bonding quality across bonding lines. Almost no reaction products were found in the diffusion region and the Nano-indentation test demonstrated that the solid solution strengthening was caused by inter-diffusion in the diffusion zone. The effect of low joining temperature on reducing reaction products and improving mechanical properties of W/Ti/Steel diffusion bonding were investigated in this paper.

Microstructure and mechanical behavior of ODS and non-ODS Fe–14Cr model alloys produced by spark plasma sintering

International Nuclear Information System (INIS)

Auger, M.A.; Castro, V. de; Leguey, T.; Muñoz, A.; Pareja, R.

2013-01-01

In this work the spark plasma sintering (SPS) technique has been explored as an alternative consolidation route for producing ultra-fine grained Fe–14Cr model alloys containing a dispersion of oxide nanoparticles. Elemental powders of Fe and Cr, and nanosized Y 2 O 3 powder have been mechanically alloyed in a planetary ball mill and rapidly sintered in a spark plasma furnace. Two alloys, with nominal compositions Fe–14%Cr and Fe–14%Cr–0.3%Y 2 O 3 (wt.%), have been fabricated and their microstructure and mechanical properties investigated. The results have been compared with those obtained for other powder metallurgy processed alloys of the same composition but consolidated by hot isostatic pressing. The SPS technique under the present conditions has produced Fe–14Cr materials that apparently exhibit different microstructures yielding inferior mechanical properties than the counterpart material consolidated by hot isostatic pressing. Although the presence of a dispersion of Y-rich particles is evident, the oxide dispersion strengthened (ODS) Fe–14Cr alloy consolidated by SPS exhibits poor tensile properties. The extensive decoration of the powder particle surfaces with Cr-rich precipitates and the residual porosity appear to be responsible for the impaired properties of this ODS alloy consolidated by SPS

Microstructure and mechanical behavior of ODS and non-ODS Fe–14Cr model alloys produced by spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Auger, M.A.; Castro, V. de [Departamento de Física, Universidad Carlos III de Madrid, 28911 Leganés (Spain); Leguey, T., E-mail: leguey@fis.uc3m.es [Departamento de Física, Universidad Carlos III de Madrid, 28911 Leganés (Spain); Muñoz, A.; Pareja, R. [Departamento de Física, Universidad Carlos III de Madrid, 28911 Leganés (Spain)

2013-05-15

In this work the spark plasma sintering (SPS) technique has been explored as an alternative consolidation route for producing ultra-fine grained Fe–14Cr model alloys containing a dispersion of oxide nanoparticles. Elemental powders of Fe and Cr, and nanosized Y{sub 2}O{sub 3} powder have been mechanically alloyed in a planetary ball mill and rapidly sintered in a spark plasma furnace. Two alloys, with nominal compositions Fe–14%Cr and Fe–14%Cr–0.3%Y{sub 2}O{sub 3} (wt.%), have been fabricated and their microstructure and mechanical properties investigated. The results have been compared with those obtained for other powder metallurgy processed alloys of the same composition but consolidated by hot isostatic pressing. The SPS technique under the present conditions has produced Fe–14Cr materials that apparently exhibit different microstructures yielding inferior mechanical properties than the counterpart material consolidated by hot isostatic pressing. Although the presence of a dispersion of Y-rich particles is evident, the oxide dispersion strengthened (ODS) Fe–14Cr alloy consolidated by SPS exhibits poor tensile properties. The extensive decoration of the powder particle surfaces with Cr-rich precipitates and the residual porosity appear to be responsible for the impaired properties of this ODS alloy consolidated by SPS.

Using bench press load to predict upper body exercise loads in physically active individuals.

Science.gov (United States)

Wong, Del P; Ngo, Kwan-Lung; Tse, Michael A; Smith, Andrew W

2013-01-01

This study investigated whether loads for assistance exercises of the upper body can be predicted from the loads of the bench press exercise. Twenty-nine physically active collegiate students (age: 22.6 ± 2.5; weight training experience: 2.9 ± 2.1 years; estimated 1RM bench press: 54.31 ± 14.60 kg; 1RM: body weight ratio: 0.80 ± 0.22; BMI: 22.7 ± 2.1 kg·m(-2)) were recruited. The 6RM loads for bench press, barbell bicep curl, overhead dumbbell triceps extension, hammer curl and dumbbell shoulder press were measured. Test-retest reliability for the 5 exercises as determined by Pearson product moment correlation coefficient was very high to nearly perfect (0.82-0.98, p bench press load was significantly correlated with the loads of the 4 assistance exercises (r ranged from 0.80 to 0.93, p bench press load was a significant (R(2) range from 0.64 to 0.86, p Bench press load (0.28) + 6.30 kg, (b) Barbell biceps curl = Bench press load (0.33) + 6.20 kg, (c) Overhead triceps extension = Bench press load (0.33) - 0.60 kg, and (d) Dumbbell shoulder press = Bench press load (0.42) + 5.84 kg. The difference between the actual load and the predicted load using the four equations ranged between 6.52% and 8.54%, such difference was not significant. Fitness professionals can use the 6RM bench press load as a time effective and accurate method to predict training loads for upper body assistance exercises. Key pointsThe bench press load was significantly correlated with the loads of the 4 assistance exercises.No significant differences were found between the actual load and the predicted load in the four equations.6RM bench press load can be a time effective and accurate method to predict training loads for upper body assistance exercises.

Evaluation of pressed shredded empty fruit bunch (EFB)-palm oil ...

African Journals Online (AJOL)

Pressed-shredded empty fruit bunches (EFB) and palm oil mill effluent (POME) anaerobic sludge from a 500 m3 closed anaerobic digester system was utilized for the co-composting treatment. Scanning electron microscopy (SEM) analysis showed that the shredding-pressing treatment on EFB gave better results in ...

Method for hot pressing beryllium oxide articles

Science.gov (United States)

Ballard, Ambrose H.; Godfrey, Jr., Thomas G.; Mowery, Erb H.

1988-01-01

The hot pressing of beryllium oxide powder into high density compacts with little or no density gradients is achieved by employing a homogeneous blend of beryllium oxide powder with a lithium oxide sintering agent. The lithium oxide sintering agent is uniformly dispersed throughout the beryllium oxide powder by mixing lithium hydroxide in an aqueous solution with beryllium oxide powder. The lithium hydroxide is converted in situ to lithium carbonate by contacting or flooding the beryllium oxide-lithium hydroxide blend with a stream of carbon dioxide. The lithium carbonate is converted to lithium oxide while remaining fixed to the beryllium oxide particles during the hot pressing step to assure uniform density throughout the compact.

The Suburban Press; First Steps toward an Annotated Bibliography. Suburban Press Research Series No. 16 and 17.

Science.gov (United States)

Northern Illinois Univ., De Kalb. Suburban Press Research Center.

This bibliography lists journal articles concerning various aspects of the suburban press. Annotated selections, arranged alphabetically according to journal title, are gathered from the following periodicals: "Advertising Age,""Business Week,""Columbia Journalism Review,""Editor and Publisher,""Grassroots Editor,""Journalism…

Engineering work plan for container venting system drill press assembly troubleshooting. Revision 1

International Nuclear Information System (INIS)

Prather, M.C.

1994-11-01

This work plan is for troubleshooting the current CVS drill press to ensure that the drill bit assembly doesn't bind in the press plate. A drill press assembly has been fabricated for the Container Venting System (CVS). The drill bit assembly has bound in the press plate in previous revisions of this design. Initial troubleshooting of the drill press per Rev. 0 of this work plan was performed at the 200W Kaiser Machine Shop under Work Package 2H9401670F, Internal Work Order E20027. The drill press operated without jamming. Then, during the pre-operational test on 11/14/17 and the operational test on 11/17/94, two drum lids were drilled. Immediately after the test on 11/17/94, the drill was again operated, and it jammed. An inspection found shavings at the bottom of the drill bit assembly, between the drill bit sleeve and the press plate bore. This revised work plan provides direction for the machine shop to diagnose and correct this recent problem

WordPress Website Development

OpenAIRE

Lassila, Joonas

2016-01-01

The aim of this Bachelor’s thesis was to develop a WordPress mobile-first style website for the customer, Pohjois-Suomen Pesis. The main purpose of the development was to learn website designing principles and create a responsive website for the mobile and desktop platforms. The development process began defining the requirements of the website and creating the requirements document. Then next step was learning how to design a website layout and to choose the colour scheme for the site. T...

Optimizing of SPS pressed SrFe12O19 pellets from nano-powder

DEFF Research Database (Denmark)

Mortensen, Anna; Stingaciu, Marian; Christensen, Mogens

2015-01-01

direction giving a higher net magnetization. One challenge is to optimize the pressing conditions in order to maximize the remanence and thus the energy product. In present work the SrFe12O19 powder was made in an autoclave and was analysed by X-ray diffraction and Rietveld Refinement to determine particle...... size. The powder was pressed using Spark Plasma Syntering (SPS) system at different conditions in order to investigate how the pressing conditions influence the magnetic properties. It was found, that pressing at 950oC leads to a much better alignment than pellets pressed at room temperature....... Furthermore, ball milling seems to decrease the degree of alignment and thereby the magnetic remanence which leads to a lower energy product. The magnetization was characterized using Vibrating Sample Magnetometer. By applying an external magnetic field before pressing, the alignment is heightened...

Reporters on the Battlefield. The Embedded Press System in Historical Context

National Research Council Canada - National Science Library

Paul, Christopher; Kim, James J

2004-01-01

While the history of relations between the press and the military predates modern journalism, much of what had gone before was neutralized by the horrible press-military breakdown that occurred during U.S...

Modelling and Simulation Based on Matlab/Simulink: A Press Mechanism

International Nuclear Information System (INIS)

Halicioglu, R; Dulger, L C; Bozdana, A T

2014-01-01

In this study, design and kinematic analysis of a crank-slider mechanism for a crank press is studied. The crank-slider mechanism is the commonly applied one as direct and indirect drive alternatives in practice. Since inexpensiveness, flexibility and controllability are getting more and more important in many industrial applications especially in automotive industry, a crank press with servo actuator (servo crank press) is taken as an application. Design and kinematic analysis of representative mechanism is presented with geometrical analysis for the inverse kinematic of the mechanism by using desired motion concept of slider. The mechanism is modelled in MATLAB/Simulink platform. The simulation results are presented herein

Modelling and Simulation Based on Matlab/Simulink: A Press Mechanism

Science.gov (United States)

Halicioglu, R.; Dulger, L. C.; Bozdana, A. T.

2014-03-01

In this study, design and kinematic analysis of a crank-slider mechanism for a crank press is studied. The crank-slider mechanism is the commonly applied one as direct and indirect drive alternatives in practice. Since inexpensiveness, flexibility and controllability are getting more and more important in many industrial applications especially in automotive industry, a crank press with servo actuator (servo crank press) is taken as an application. Design and kinematic analysis of representative mechanism is presented with geometrical analysis for the inverse kinematic of the mechanism by using desired motion concept of slider. The mechanism is modelled in MATLAB/Simulink platform. The simulation results are presented herein.

Eye-Pressing by Visually Impaired Children.

Science.gov (United States)

Jan, James E.; And Others

1983-01-01

The nature of eye-pressing as a visual stimulation mannerism in children with severely impaired eyesight is examined, and a possible physiological explanation (that self-stimulation occurs when the demand of the brain for meaningful visual information is not met) is offered. (CL)

The Law Enforcement of Journalism Profession in The Context of Press Freedom

Directory of Open Access Journals (Sweden)

Sri Ayu Astuti

2014-06-01

Full Text Available Law No. 40 of 1999 on Press is a manifestation of respect for the legal protection of press workers . Press in their role contributes to the intellectual level of the nation, through the information submitted in news publications, as well as bringing stipulated by the 1945 Constitution of Republic of Indonesia on freedom of thought and speech as Human Rights. However, in carrying out their journalistic duties, the Press should have responsibilities in the news process, and must not violate the ethics of his profession. Press that violates profession intentionally or unintentionally in the writing and publication of news in the public sphere, will still do the law enforcement process for any misuse of the meaning of freedom of speech and thought that harm others. Enforcement of this law, in line with the revocation of the right of immunity of profession issued by the Constitutional Court, which means the Press as a Professional must do the job with the precautionary principle, not by carelessness due to the trapped arrogance of jobs, and injuring other people's human rights, even doing work profession with not commendable behavior. How To Cite: Astuti, S. (2014. The Law Enforcement of Journalism Profession in The Context of Press Freedom. Rechtsidee, 1(2, 175-190. doi:http://dx.doi.org/10.21070/jihr.v1i2.97

Research Facility for Mechanical Press Closed Gap Adjuster

Directory of Open Access Journals (Sweden)

A. A. Ancifirov

2016-01-01

Full Text Available The article describes an example of the research facility for closed gap adjustment mechanism based on the KD2128 closed-die forging press. Its rated force with a servo drive used is 630kN. The servo drive consists of a motor with nominal power of 1.57kW and a frequency converter with power of 7.5kW, which has functions of the programmable logic controller.The article notes that such a facility is expedient and useful for practical classes on forging-andstamping machines at the BMSTU Department of «Technology processing by pressure» to demonstrate the capabilities of existing technological facility, learn a design of forging-andstamping machine units, solve the problems of automatic control, monitoring, and diagnostics in blank manufacturing.The article presents a detailed facility diagram of the closed gap adjustment mechanism and its photograph, describes the mechanism and its basic parameters, gives characteristics of the synchronous motor to drive the mechanism, reviews practical works, which the research facility may provide.Based on the four experiments the article estimates an efficiency of the research facilityuse under consideration, especially when modeling a servo motor shaft under the maximum load. The relevant diagrams confirm experimental results, namely: control current, angle of motor shaft and its speed versus time. Thus, upon the diagram analysis it can be noted that the research facility design allows providing kinematics and dynamics of the press closed gap adjuster.This article describes how to determine the closed gap adjusting accuracy of the press. Eight experiments have been conducted to evaluate a working out control signal to the linear movement of the press punch when using the research facility. It is noted that the linear positioning accuracy of the press punch reaches the hundredth parts of a millimeter of the adjustment value that is sufficient to achieve the required precision when performing operations such as

The Devotio Moderna and the Printing Press (ca. 1475-1540)

NARCIS (Netherlands)

Goudriaan, K.

2013-01-01

Six presses owned by religious houses belonging to the Devotio Moderna were active during the period 14751540, five of them run by Brethren of the Common Life, the sixth by Regular Canons. The question is raised whether the production of these presses can be correlated with the nature of this

Preliminary results for HIP bonding Ta to W targets for the materials test station

Energy Technology Data Exchange (ETDEWEB)

Dombrowski, David E [Los Alamos National Laboratory; Maloy, Stuart A [Los Alamos National Laboratory

2009-01-01

Tungsten targets for the Materials Test Station (MTS) were clad with thin tantalum cover plates and a tantalum frame using hot isostatic pressing (HIP). A preliminary HIP parameter study showed good bonding and intimate mechanical contact for Ta cover plate thicknesses of 0.25 mm (0.010 inch) and 0.38 mm (0.015 inch). HIP temperatures of full HIP runs were 1500 C (2732 F). HIP pressure was 203 MPa (30 ksi).

Criticism of the Press: Its Social, Psychological and Political Origins.

Science.gov (United States)

Becker, Lee B.; And Others

This study examines data from several national polls about press coverage during the Watergate scandal, in order to assess the origins of press criticism. The polls were conducted between 28 September and 6 October 1973, during June 1974, and in August 1974. The data suggest that political variables--particularly support of Nixon, party…

Design, manufacture and performance research of double acting hydraulic press

OpenAIRE

Koc, Erdem; Unver, Ertu; Ozturk, Hidayet

1990-01-01

This research presents the design and production of a double acting 40 tons capacity hydraulic press. The issues in the design, engineering manufacturing of the hydraulic press are reported specifically on both cylinders generating the same pressure and velocity using a solenoid directional control valve and a flow separating valve. (In Turkish)

Asynchronous decision making in a memorized paddle pressing task.

Science.gov (United States)

Dankert, James R; Olson, Byron; Si, Jennie

2008-12-01

This paper presents a method for asynchronous decision making using recorded neural data in a binary decision task. This is a demonstration of a technique for developing motor cortical neural prosthetics that do not rely on external cued timing information. The system presented in this paper uses support vector machines and leaky integrate-and-fire elements to predict directional paddle presses. In addition to the traditional metrics of accuracy, asynchronous systems must also optimize the time needed to make a decision. The system presented is able to predict paddle presses with a median accuracy of 88% and all decisions are made before the time of the actual paddle press. An alternative bit rate measure of performance is defined to show that the system proposed here is able to perform the task with the same efficiency as the rats.

Hot and cold pressing of (La,Ce)PO4-based nuclear waste forms

International Nuclear Information System (INIS)

Floran, R.J.; Rappaz, M.; Abraham, M.M.; Boatner, L.A.

1981-01-01

Synthetic analogs of the mineral monazite [(Ce,La,Ca,Th,U)(P,Si)O 4 ] are promising host phases for the isolation of actinide wastes. In the present investigation, the optimal conditions necessary to form high-density, simulated waste pellets from calcined LaPO 4 and CePO 4 powders have been examined. Pellets that are close to the theoretical density are necessary in order to minimize porosity and hence potential avenues along which fluid/waste interactions can take place. Calcined powders prepared by a urea precipitation process were cold pressed and hot pressed under a range of controlled conditions to form coherent, cylindrical pellets. Changes in density were examined as a function of pressure, temperature and duration of sintering. For cold-pressed pellets, a significant increase in density occurs during sintering between 1000 0 C and 1100 0 C. This increase is correlated with substantial grain coarsening of the pellet microstructure. A comparison of cold and hot pressing techniques suggests that, only after sintering, does the density of cold-pressed pellets approach (but not equal) that of the hot-pressed pellets. Densities >90% of the theoretical value of 5.11 g/cm 3 are easily attainable by hot pressing without sintering. The significance of density differences on pellet stability will be investigated in future leaching studies. The apparent advantages of the higher densities achieved by hot pressing must be weighed against the increased technological/engineering complexities involved when working at sustained high temperatures in a remote environment. Thus the cold pressing technique may ultimately prove more practical for large-scale commercial operations

Structure and characteristics of the hot pressed hydroxyapatite/poly-L-lactide composite

Directory of Open Access Journals (Sweden)

Ignjatović Nenad L.

2002-01-01

Full Text Available Hydroxyapatite/poly-L-lactide (HAp/PLL composite biomaterial can be obtained by different processing methods. Three-dimensional blocks of HAp/PLLA composite biomaterial with mechanical characteristics close to the natural bone tissue can be obtained by hot pressing procedure. Effects of synthesis and compacting on the structure and characteristics of the HAp/PLLA composite biomaterial were studied in this work. Using wade angle X-ray structural analyses (WAXS, differentially scanning calorimetry (DSC, thermogravimetric analysis (TGA and infrared (IR spectroscopy, the changes occurring in the material during synthesis and hot pressing were monitored. Surface microstructure was analyzed by scanning electronic microscopy (SEM coupled with electron-dispersion analysis (EDX. The results obtained indicate a possible decrease in the degree of crystallinity with hot pressing time increase. A block of HAp/PLLA composite biomaterial with 1.6 times lower crystallinity of the polymer phase was obtained by hot pressing in a given time interval with a maximum of 60 minutes. Results of TG analysis show that PLLA stability decreases with increasing hot pressing time, and vice versa. IR study proved that neither destructive changes in constituents nor formation of new phases occurred during hot pressing.

Production data in media systems and press front ends: capture, formats and database methods

Science.gov (United States)

Karttunen, Simo

1997-02-01

The nature, purpose and data presentation features of media jobs are analyzed in relation to the content, document, process and resource management in media production. Formats are the natural way of presenting, collecting and storing information, contents, document components and final documents. The state of the art and the trends in the media formats and production data are reviewed. The types and the amount of production data are listed, e.g. events, schedules, product descriptions, reports, visual support, quality, process states and color data. The data exchange must be vendor-neutral. Adequate infrastructure and system architecture are defined for production and media data. The roles of open servers and intranets are evaluated and their potential roles as future solutions are anticipated. The press frontend is the part of print media production where large files dominate. The new output alternatives, i.e. film recorders, direct plate output (CTP and CTP-on-press) and digital, plateless printing lines need new workflow tools and very efficient file and format management. The paper analyzes the capture, formatting and storing of job files and respective production data, such as the event logs of the processes. Intranet, browsers, Java applets and open web severs will be used to capture production data, especially where intranets are used anyhow, or where several companies are networked to plan, design and use documents and printed products. The user aspects of installing intranets is stressed since there are numerous more traditional and more dedicated networking solutions on the market.

Shoulder Muscle Activation of Novice and Resistance Trained Women during Variations of Dumbbell Press Exercises

Science.gov (United States)

Luczak, Joshua; Bosak, Andy; Riemann, Bryan L.

2013-01-01

Previous research has compared the effects of trunk inclination angle on muscle activation using barbells and Smith machines in men. Whether similar effects occur with the use of dumbbells or in women remains unknown. The purpose was to compare upper extremity surface electromyographical (EMG) activity between dumbbell bench, incline, and shoulder presses. Dominate arm EMG data were recorded for collegiate-aged female resistance trained individuals (n = 12) and novice female resistance trained exercisers (n = 12) from which average EMG amplitude for each repetition phase (concentric, eccentric) was computed. No significant differences were found between experienced and novice resistance trained individuals. For the upper trapezius and anterior deltoid muscles, shoulder press activation was significantly greater than incline press which in turn was significantly greater than bench press across both phases. The bench and incline presses promoted significantly greater pectoralis major sternal activation compared to the shoulder press (both phases). While pectoralis major clavicular activation during the incline press eccentric phase was significantly greater than both the bench and shoulder presses, activation during the bench press concentric phase promoted significantly greater activation than the incline press which in turn was significantly greater than the shoulder press. These results provide evidence for selecting exercises in resistance and rehabilitation programs. PMID:26464884

Shoulder Muscle Activation of Novice and Resistance Trained Women during Variations of Dumbbell Press Exercises

Directory of Open Access Journals (Sweden)

Joshua Luczak

2013-01-01

Full Text Available Previous research has compared the effects of trunk inclination angle on muscle activation using barbells and Smith machines in men. Whether similar effects occur with the use of dumbbells or in women remains unknown. The purpose was to compare upper extremity surface electromyographical (EMG activity between dumbbell bench, incline, and shoulder presses. Dominate arm EMG data were recorded for collegiate-aged female resistance trained individuals ( and novice female resistance trained exercisers ( from which average EMG amplitude for each repetition phase (concentric, eccentric was computed. No significant differences were found between experienced and novice resistance trained individuals. For the upper trapezius and anterior deltoid muscles, shoulder press activation was significantly greater than incline press which in turn was significantly greater than bench press across both phases. The bench and incline presses promoted significantly greater pectoralis major sternal activation compared to the shoulder press (both phases. While pectoralis major clavicular activation during the incline press eccentric phase was significantly greater than both the bench and shoulder presses, activation during the bench press concentric phase promoted significantly greater activation than the incline press which in turn was significantly greater than the shoulder press. These results provide evidence for selecting exercises in resistance and rehabilitation programs.

A new press line concept for conveyor belts; Neues Pressenkonzept fuer Foerdergurte

Energy Technology Data Exchange (ETDEWEB)

Aumueller, Steffen [Siempelkamp Maschinen- und Anlagenbau GmbH und Co. KG, Krefeld (Germany)

2010-06-15

Pressure and temperature are the relevant process parameters for the vulcanisation of rubber products. Particularly, the vulcanisation of large-surface rubber products such as belt conveyors sets large requirements on the mechanical characteristics of the press lines. Siempelkamp Maschinen- und Anlagenbau GmbH and Co. KG (Krefeld, Federal Republic of Germany) is specialized on these requirements. For over 100 years, this company constructs vulcanisation presses for the belt conveyor industry. In the first ten decades, the layout of the press lines according to stiffness and transmission of large forces were in the focus. Till to the late 1980ies, these press lines represented the standard of the belt conveyor industry.

Dynamic Multiaxial Response of a Hot-Pressed Aluminum Nitride

Science.gov (United States)

2012-01-05

Hutchinson, Adv. Appl . Mech. 29 (1992). [34] H. Ming-Yuan, J.W. Hutchinson, Int. J. Solids Struct. 25 (1989) 1053. [35] J. Salem , L. Ghosn, Int. J...Dynamic Multiaxial Response of a Hot- Pressed Aluminum Nitride by Guangli Hu, C. Q. Chen, K. T. Ramesh, and J. W. McCauley ARL-RP-0487...Laboratory Aberdeen Proving Ground, MD 21005-5066 ARL-RP-0487 June 2014 Dynamic Multiaxial Response of a Hot- Pressed Aluminum Nitride

Comparison of concentric and eccentric bench press repetitions to failure.

Science.gov (United States)

Kelly, Stephen B; Brown, Lee E; Hooker, Steven P; Swan, Pamela D; Buman, Matthew P; Alvar, Brent A; Black, Laurie E

2015-04-01

Eccentric muscle actions (ECC) are characterized by muscle lengthening, despite actin-myosin crossbridge formation. Muscles acting eccentrically are capable of producing higher levels of force compared with muscles acting concentrically. The purpose of this study was to determine whether ECC bench press yields greater strength than concentric (CON) as determined by 1 repetition maximum (1RM). Additionally, a comparison was made examining differences in the number of repetitions to failure at different relative intensities of 1RM. Thirty healthy men (age = 24.63 ± 5.6 years) were tested for 1RM in CON and ECC bench press and the number of repetitions completed at 60, 70, 80, and 90% 1RM. For CON repetitions, the weight was mechanically lowered to the chest, and the participant pressed it up until the elbows were fully extended. The ECC bench press consisted of lowering a barbell from a fully extended elbow position to the chest in a continuous controlled manner for 3 seconds as determined by electronic metronome. Paired t-tests showed that ECC 1RM (115.99 ± 31.08 kg) was significantly (p ≤ 0.05) greater than CON 1RM (93.56 ± 26.56 kg), and the number of repetitions completed at 90% 1RM was significantly (p ≤ 0.05) greater in ECC (7.67 ± 3.24) as compared with CON (4.57 ± 2.21). There were no significant differences in number of completed repetitions during CON and ECC bench press at 60, 70, and 80% 1RM. These data indicate that ECC actions yield increased force capabilities (∼120%) as compared with CON in the bench press and may be less prone to fatigue, especially at higher intensities. These differences suggest a need to develop unique strategies for training eccentrically.

Reducing VOC Press Emission from OSB Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Dr. Gary D. McGinnis; Laura S. WIlliams; Amy E. Monte; Jagdish Rughani: Brett A. Niemi; Thomas M. Flicker

2001-12-31

Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board.

Freedom of the Press – two concepts

Directory of Open Access Journals (Sweden)

Markus Meckl

2015-03-01

Full Text Available In 1644 the debate for freedom of expression started in modern times thanks to John Milton’s Areopagitica, where he still argued about God in order to justify his quest for freedom. With the enlightenment God lost his unifying role for society and could no longer serve as justification. Two arguments were brought then forward to justify freedom of the press: One by the continental movement of the enlightenment; the other from within the movement of utilitarianism, and most influentially by John Stuart Mill. Both underlined the importance of truth; however, they differed in their understanding on what truth was good for. This difference in their arguments had a lasting impact on the debate on the limits of freedom of the press.

Solidification of glass powder by a hydrothermal hot-pressing technique

International Nuclear Information System (INIS)

Nishioka, Mamoru; Yanagisawa, Kazumichi; Yamasaki, Nakamichi

1986-01-01

A borosilicate glass powder was solidified with a NaOH solution or distilled water by the hydrothermal hot-pressing technique. The effect of hydrothermal conditions on the compressive strength was investigated, and the densification mechanism of the glass powder during the hydrothermal hot-pressing was discussed in terms of isothermal shrinkage. The glass powder was successfully solidified by hydrothermal hot-pressing at a reaction temperature lower than that of an ordinary pressure sintering. The solidified body obtained in the presence of distilled water (10 wt%) at 280 deg C had a high compressive strength of about 2300 kg/cm 2 . The analysis of initial densification process of the glass powder in hydrothermal hot-pressing with Murray's rate equation revealed that the densification proceeds both by viscous flow and by rearrangement process. Analysis of the shrinkage rates with a rate equation of hydrothermal reaction suggested that the dissolution of particles into solution controlled the initial densification of the glass powder, and that the alkaline metal acted as a catalyst. (author)

World Gravity Map: a set of global complete spherical Bouguer and isostatic anomaly maps and grids

Science.gov (United States)

Bonvalot, S.; Balmino, G.; Briais, A.; Kuhn, M.; Peyrefitte, A.; Vales, N.; Biancale, R.; Gabalda, G.; Reinquin, F.

2012-04-01

We present here a set of digital maps of the Earth's gravity anomalies (surface free air, Bouguer and isostatic), computed at Bureau Gravimetric International (BGI) as a contribution to the Global Geodetic Observing Systems (GGOS) and to the global geophysical maps published by the Commission for the Geological Map of the World (CGMW) with support of UNESCO and other institutions. The Bouguer anomaly concept is extensively used in geophysical interpretation to investigate the density distributions in the Earth's interior. Complete Bouguer anomalies (including terrain effects) are usually computed at regional scales by integrating the gravity attraction of topography elements over and beyond a given area (under planar or spherical approximations). Here, we developed and applied a worldwide spherical approach aimed to provide a set of homogeneous and high resolution gravity anomaly maps and grids computed at the Earth's surface, taking into account a realistic Earth model and reconciling geophysical and geodetic definitions of gravity anomalies. This first version (1.0) has been computed by spherical harmonics analysis / synthesis of the Earth's topography-bathymetry up to degree 10800. The detailed theory of the spherical harmonics approach is given in Balmino et al., (Journal of Geodesy, 2011). The Bouguer and terrain corrections have thus been computed in spherical geometry at 1'x1' resolution using the ETOPO1 topography/bathymetry, ice surface and bedrock models from the NOAA (National Oceanic and Atmospheric Administration) and taking into account precise characteristics (boundaries and densities) of major lakes, inner seas, polar caps and of land areas below sea level. Isostatic corrections have been computed according to the Airy-Heiskanen model in spherical geometry for a constant depth of compensation of 30km. The gravity information given here is provided by the Earth Geopotential Model (EGM2008), developed at degree 2160 by the National Geospatial

28 CFR 540.64 - Press pools.

Science.gov (United States)

2010-07-01

... Judicial Administration BUREAU OF PRISONS, DEPARTMENT OF JUSTICE INSTITUTIONAL MANAGEMENT CONTACT WITH PERSONS IN THE COMMUNITY Contact With News Media § 540.64 Press pools. (a) The Warden may establish a... shall notify all news media representatives who have requested interviews or visits that have not been...

Crystallization behavior and properties of BaO-Al2O3-2SiO2 glass matrices

Science.gov (United States)

Drummond, Charles H., III; Bansal, Narottam P.

1990-01-01

Glass of stoichiometric celsian composition, BaO-Al2O3-SiO2, has a density of 3.39 g/cu cm, a thermal expansion coefficient of 6.6 x 10 to the -6th/C, a glass-transition temperature of 910 C, and a dilatometric softening point of 925 C. On heat treatment, only hexacelsian crystallized out on the surface, but both celsian and hexacelsian were present in the bulk. Effects of cold isostatic pressing (CIP), sintering, and hot-pressing, in the presence and absence of an additive, on the formation of the celsian phase in the glass have been studied. CIP'd samples, after appropriate heat treatments, always crystallized out as celsian, whereas presence of 5-10 wt pct of an additive was necessary for formation of celsian in sintered as well as hot-pressed specimens. Green density increased with CIP'ing pressure but had no effect on sintered density. Hot-pressing resulted in fully dense samples.

A CONCEPTUAL APPROACH ON PRESS CONFERENCE

Directory of Open Access Journals (Sweden)

Ioana Olariu

2015-07-01

Full Text Available A press conference is an important tool of public relations. The primary role of public relations is to manage a company’s reputation and help build public consent for its enterprises. The goal of PR is to develop and maintain goodwill with most, if not all, of its publics. Failure to do so may mean loss of customers and revenues, time lost dealing with complaints or lawsuits, and loss of esteem. A company’s publics change constantly. Well-executed public relations is an ongoing process that molds good long-term relationships and plays an important role in relationship marketing and integrated communications. Companies often call press conference when they have significant news to announce, such as the introduction of a new product or advertising campaign. Although used less often by organizations and corporations, this form of delivery can be very effective. The topic must be of major interest to a specific group before it is likely to gain coverage.

Bench press exercise: the key points.

Science.gov (United States)

Padulo, J; Laffaye, G; Chaouachi, A; Chamari, K

2015-06-01

The bench press exercise (BPE) is receiving increasing interest as a field testing, training/therapeutic modality to improve neuromuscular performance or to increase bone mass density. Several studies have been performed using BPE as a standard for increasing upper-limb strength. For this purpose, the position of the bar, the loads, the sets, the number of repetitions, the recovery time in-between sets, the movement speed, the muscular work and the use of the determination of the one repetition maximum (1-RM) are the classical tools investigated in the literature that have been shown to affect the BPE effect on neuromuscular. The goal of the present short review is to make a picture of the current knowledge on the bench press exercise, which could be very helpful for a better understanding of this standard movement and its effects. Based on the related literature, several recommendations on these key points are presented here.

New system for measuring and controlling the maximum pressing pressure in the holes of the mould: ISOPRESS; Nuevo sistema para la medida y control de la presion maxima de prensado en los alveolos del molde: ISOPRESS

Energy Technology Data Exchange (ETDEWEB)

Poyatos, A.; Bonaque, R.; Mallol, G.; Boix, J.

2012-07-01

The organization MACER, in collaboration with the Institute of Ceramic Technology, has developed the system ISOPRESS, an integrated control device that permits to equal automatically the maximum pressure applied on the powder contained in each of the holes of the mould. This system consists of a set of pressure transducers which are located in the isostatic punches of the mould itself. With them it is possible to register in real-time the evolution of the measured pressure of the oil contained in the compensation chamber of each punch. All the transducers are connected to a data acquisition system which transfers the pressure values to a PC which performs the signal processing to obtain the pressure maximum value reached during a pressing cycle, in each one of the holes. The system is completed with a control software especially developed, that permits to regulate individually the height of the first fall of each inferior punch to guarantee the uniformity of the pressure applied in all the holes. ISOPRESS, by assuring the constancy of the bulk density of all the pieces processed, guarantees a unique piece size and minimize production problems associated to the variability of the bulk density of the pieces. (Author)

Microstructural evolution of bainitic steel severely deformed by equal channel angular pressing.

Science.gov (United States)

Nili-Ahmadabadi, M; Haji Akbari, F; Rad, F; Karimi, Z; Iranpour, M; Poorganji, B; Furuhara, T

2010-09-01

High Si bainitic steel has been received much of interest because of combined ultra high strength, good ductility along with high wear resistance. In this study a high Si bainitic steel (Fe-0.22C-2.0Si-3.0Mn) was used with a proper microstructure which could endure severe plastic deformation. In order to study the effect of severe plastic deformation on the microstructure and properties of bainitic steel, Equal Channel Angular Pressing was performed in two passes at room temperature. Optical, SEM and TEM microscopies were used to examine the microstructure of specimens before and after Equal Channel Angular Pressing processing. X-ray diffraction was used to measure retained austenite after austempering and Equal Channel Angular Pressing processing. It can be seen that retained austenite picks had removed after Equal Channel Angular Pressing which could attributed to the transformation of austenite to martensite during severe plastic deformation. Enhancement of hardness values by number of Equal Channel Angular Pressing confirms this idea.